WorldWideScience

Sample records for irrigation application techniques

  1. Irrigation water management: Basic principles and applications

    OpenAIRE

    Ella, Victor B.

    2007-01-01

    This presentation defines the term, irrigation, as well as explains the common methods of irrigation in attempt to define the fundamental principles needed to wisely design an irrigation system. It outlines a typical drip irrigation set-up, and discusses management of an irrigation system, including water volume application suggestions. LTRA-5 (Agroforestry and Sustainable Vegetable Production)

  2. ROOT CANAL IRRIGANTS AND IRRIGATION TECHNIQUES: A REVIEW

    OpenAIRE

    Aniketh; Mohamed; Geeta; Nandakishore; Gourav Kumar; Patrick Timothy; Jayson Mathew; Sahle Abdul

    2015-01-01

    Root canal irrigation is not much emphasised in endodontic therapy. Most articles discussed are on root canal shaping and obturation not much emphasis is given for irrigation. There are many irrigation solutions which are introduced into market. The primary objective of root canal therapy is the ret ention of the pulpless or pulpally involved tooth with its associated periapical tissues in a healthy state. Achievement of this objective requires that the pulpal spaces and con...

  3. Evaluation of Modern Irrigation Techniques with Brackish Water

    OpenAIRE

    Aboulila, Tarek Selim

    2012-01-01

    Modern irrigation techniques are becoming increasingly important in water-scarce countries especially in arid and semiarid regions. Higher crop production and better water use efficiency are usually achieved by drip irrigation as compared to other irrigation methods. Furthermore, by using drip irrigation simultaneously with brackish irrigation water, some of the water stress due to shortage of fresh water resources can be managed. The objective of the current study was to investigate the infl...

  4. Effects of seven different irrigation techniques on debris and the ...

    African Journals Online (AJOL)

    Aim: Conventional manual irrigation with a syringe and needle remains widely accepted technique in the irrigation procedures. However, its flushing action has some limitations. Currently, several techniques and systems are available and reported to improve the insufficiency of syringe irrigation. The aim of this study was to ...

  5. Review of root canal irrigant delivery techniques and devices

    Directory of Open Access Journals (Sweden)

    Yeon-Jee Yoo

    2011-05-01

    Full Text Available Introduction Eliminating the residual debris and bacteria in the root canal system is one of the main purposes of the endodontic treatment. However, the complexity on the anatomy of the root canal system makes it difficult to eliminate the bacterial biofilm existing along the root canal surface and necrotic pulp tissue by mechanical instrumentation and chemical irrigation. Recently, more effective irrigant delivery systems for root canal irrigation have been developed. The purpose of this review was to present an overview of root canal irrigant delivery techniques and devices available in endodontics. Review The contents of this paper include as follows; - syringe-needle irrigation, manual dynamic irrigation, brushes - sonic and ultrasonic irrigation, passive ultrasonic irrigation, rotary brush, RinsEndo, EndoVac, Laser Conclusion Though technological advances during the last decade have brought to fruition new agitation devices that rely on various mechanisms, there are few evidence based study to correlate the clinical efficacy of these devices with improved outcomes except syringe irrigation with needle and ultrasonic irrigation. The clinicians should try their best efforts to deliver antimicrobial and tissue solvent solutions in predictable volumes safely to working length.

  6. Green and blue water footprint reduction in irrigated agriculture: effect of irrigation techniques, irrigation strategies and mulching

    Science.gov (United States)

    Chukalla, A. D.; Krol, M. S.; Hoekstra, A. Y.

    2015-12-01

    Consumptive water footprint (WF) reduction in irrigated crop production is essential given the increasing competition for freshwater. This study explores the effect of three management practices on the soil water balance and plant growth, specifically on evapotranspiration (ET) and yield (Y) and thus the consumptive WF of crops (ET / Y). The management practices are four irrigation techniques (furrow, sprinkler, drip and subsurface drip (SSD)), four irrigation strategies (full (FI), deficit (DI), supplementary (SI) and no irrigation), and three mulching practices (no mulching, organic (OML) and synthetic (SML) mulching). Various cases were considered: arid, semi-arid, sub-humid and humid environments in Israel, Spain, Italy and the UK, respectively; wet, normal and dry years; three soil types (sand, sandy loam and silty clay loam); and three crops (maize, potato and tomato). The AquaCrop model and the global WF accounting standard were used to relate the management practices to effects on ET, Y and WF. For each management practice, the associated green, blue and total consumptive WF were compared to the reference case (furrow irrigation, full irrigation, no mulching). The average reduction in the consumptive WF is 8-10 % if we change from the reference to drip or SSD, 13 % when changing to OML, 17-18 % when moving to drip or SSD in combination with OML, and 28 % for drip or SSD in combination with SML. All before-mentioned reductions increase by one or a few per cent when moving from full to deficit irrigation. Reduction in overall consumptive WF always goes together with an increasing ratio of green to blue WF. The WF of growing a crop for a particular environment is smallest under DI, followed by FI, SI and rain-fed. Growing crops with sprinkler irrigation has the largest consumptive WF, followed by furrow, drip and SSD. Furrow irrigation has a smaller consumptive WF compared with sprinkler, even though the classical measure of "irrigation efficiency" for furrow

  7. Column leaching experiments of a uranium ore by atomizing irrigation technique

    International Nuclear Information System (INIS)

    Zeng Yingying; Lei Zeyong; Chen Haihui

    2007-01-01

    Column leaching experiments ora uranium ore were made by atomizing irrigation technique. The leaching results are compared with the results obtained by spray irrigation and drip irrigation techniques respectively under the same conditions of column leaching experiments. The results show that the atomizing irrigation technique has more uniform solution distribution, higher leaching rate, shorter leaching period, and less ratio of liquid to solid. Consequently, the atomizing irrigation technique is suitable to the ore. (authors)

  8. A simplified technique for a totally diverting transverse loop colostomy and distal irrigation.

    Science.gov (United States)

    Rose, D; Koniges, F; Frazier, T G

    1985-12-01

    This technique of totally diverting loop colostomy may be performed as an independent procedure or with exploratory laparotomy and surgical treatment on the distal part of the colon. Either a transverse or sigmoid loop colostomy can be used for diversion without the risk of fecal contamination of the peritoneal cavity, particularly when working with unprepared intestine. When distal irrigation is desired to purge the intestine of fecal material, either intraoperatively or as part of a subsequent intestinal preparation, it can easily be accomplished by placing an irrigating catheter distal to the staple line. In addition, the use of a small rubber suspension bar facilitates application of standard colostomy appliances for the stoma.

  9. Irrigation methods for efficient water application: 40 years of South ...

    African Journals Online (AJOL)

    The purpose of an irrigation system is to apply the desired amount of water, at the correct application rate and uniformly to the whole field, at the right time, with the least amount of non-beneficial water consumption (losses), and as economically as possible. We know that irrigated agriculture plays a major role in the ...

  10. Effect of irrigation frequency and application levels of sulphur ...

    African Journals Online (AJOL)

    Administrator

    2011-09-21

    Sep 21, 2011 ... both years of experimentation, application of two irrigations significantly increased the India ... marginal lands with poor fertility under rainfed conditions. ... and 40 kg K20 ha-1 as muriate of potash was applied to each plot.

  11. Advanced techniques using the plant as indicator of irrigation management

    Directory of Open Access Journals (Sweden)

    Barbara dos Santos Esteves

    2015-05-01

    Full Text Available The methodologies which are considered the most promising for irrigation management are those based on the analysis of the water status of the plants themselves. This justifies the study and improvement of indicators based on automatic and continuous measures to enable real-time monitoring data, as indices from sap flow, dendrometry and leaf turgor pressure techniques. The aim of this paper is to analyze such methodologies in order to demonstrate their principles, advantages and challenges. In conclusion, the methodologies analyzed still have many technological advances and challenges before being presented to the final user. The future research should work these tools for elaboration of technical indexes that allow their simplification, on the instrumental point of view, and the interpretation of their results.

  12. Biogeosystem technique as a base of Sustainable Irrigated Agriculture

    Science.gov (United States)

    Batukaev, Abdulmalik

    2016-04-01

    The world water strategy is to be changed because the current imitational gravitational frontal isotropic-continual paradigm of irrigation is not sustainable. This paradigm causes excessive consumption of fresh water - global deficit - up to 4-15 times, adverse effects on soils and landscapes. Current methods of irrigation does not control the water spread throughout the soil continuum. The preferable downward fluxes of irrigation water are forming, up to 70% and more of water supply loses into vadose zone. The moisture of irrigated soil is high, soil loses structure in the process of granulometric fractions flotation decomposition, the stomatal apparatus of plant leaf is fully open, transpiration rate is maximal. We propose the Biogeosystem technique - the transcendental, uncommon and non-imitating methods for Sustainable Natural Resources Management. New paradigm of irrigation is based on the intra-soil pulse discrete method of water supply into the soil continuum by injection in small discrete portions. Individual volume of water is supplied as a vertical cylinder of soil preliminary watering. The cylinder position in soil is at depth form 10 to 30 cm. Diameter of cylinder is 1-2 cm. Within 5-10 min after injection the water spreads from the cylinder of preliminary watering into surrounding soil by capillary, film and vapor transfer. Small amount of water is transferred gravitationally to the depth of 35-40 cm. The soil watering cylinder position in soil profile is at depth of 5-50 cm, diameter of the cylinder is 2-4 cm. Lateral distance between next cylinders along the plant raw is 10-15 cm. The soil carcass which is surrounding the cylinder of non-watered soil remains relatively dry and mechanically stable. After water injection the structure of soil in cylinder restores quickly because of no compression from the stable adjoining volume of soil and soil structure memory. The mean soil thermodynamic water potential of watered zone is -0.2 MPa. At this potential

  13. Nuclear techniques in flower production. Soil and irrigation fertility

    International Nuclear Information System (INIS)

    2001-01-01

    Bad soil management; the nutrients and water used in ornamental cultivation are the cause for considerable reductions in productivity here in Ecuador. It's essential to take measures to reduce the accumulation of salts and the degeneration of soils to minimum, and to put back those nutrients that have been exported by the harvesting of ornamental crops. In this way we can maintain an ecologically, socially and economically sustainable flower industry. Nuclear techniques such as radioisotopes and stable isotopes are used to track the final destination of the fertilizers that have been applied to the soil and to determine the availability of these for plants. The Ecuadorian Atomic Energy Commission (CEEA) in collaboration with the Central University of Ecuador have carried out studies using the isotopic tracers Nitrogen 15 (N-15), Phosforus 32 (P-32), Rubide-85 (Rb-85) as tracers for Potassium (K). These studies have shown that only a part of the nigrogenized fertilizer applied to the soil is useful in the growing of roses, and a large part of the nitrogen escapes in the the environment thereby contaminating the water table in the form of nitrites, depending on he way and the time of year that the fertilizer has been applied. The best form of fertilizer in rose growing for example is with the nitrogen, phosphorus, potassium and other nutrients in fractioned from always using fertilized irrigation with a dose of 1300 kg of N, 200 Kg of P, 1600 kg of K per hectare/year. This differs form norm in plantations where a weekly-fertilized irrigation is used whilst on other days only watering is used. A 30% increase in production was achieved with a 50% increase in the absorption of nitrogen and a 40% increase in potassium. These studies have shown the tremendous cost saving in terms of the importing of fertilizers, as well as the decrease in the use of contaminating fertilizers. (The author)

  14. Green and blue water footprint reduction in irrigated agriculture: effect of irrigation techniques, irrigation strategies and mulching

    NARCIS (Netherlands)

    Chukalla, Abebe Demissie; Krol, Martinus S.; Hoekstra, Arjen Ysbert

    2015-01-01

    Consumptive water footprint (WF) reduction in irrigated crop production is essential given the increasing competition for freshwater. This study explores the effect of three management practices on the soil water balance and plant growth, specifically on evapotranspiration (ET) and yield (Y) and

  15. The effects of three techniques that change the wetting patterns over subsurface drip-irrigated potatoes

    Energy Technology Data Exchange (ETDEWEB)

    Elnesr, M.N.; Alazba, A.A.

    2015-07-01

    Wetting pattern enhancement is one of the goals of irrigation designers and researchers. In this study, we addressed three techniques (dual-lateral drip, intermittent flow and physical barrier methods) that change the wetting pattern of subsurface drip irrigation. To study their effect on the yield and water-use efficiency (WUE) of potatoes, field experiments were conducted for four seasons, during which the soil-water balance was continuously monitored using a set of capacitance probes. The results of the soil water patterns showed that both the dual-lateral and intermittent techniques increased lateral water movement and eliminated deep percolation, whereas the physical barrier had a limited effect on the top soil layer. The crop results indicated that the yield and WUE increased significantly in response to the application of the dual-lateral drip (up to 30%); the intermittent application also positively affected the yield (~10%) and the WUE (~14%), but these effects were not statistically significant according to the statistical model. The physical barrier showed a non-significant negative effect on the yield and WUE. These findings suggest the following recommended practices: the use of dual-lateral drip technique due to its beneficial results and its potential for increasing yields and reducing water consumption; the application of intermittent flow with more than three surges; and restricting the use of physical barriers to soils with high permeability. (Author)

  16. Optimal design of pressurized irrigation systems. Application cases (Ecuador

    Directory of Open Access Journals (Sweden)

    Carmen Mireya Lapo Pauta

    2013-05-01

    Full Text Available This paper presents research completed with the intention of finding the most economical solution in the design of pressurized irrigation networks, while efficiently meet service delivery. A systematic methodology is proposed that combines two optimization techniques through a “hybrid method” in, which linear programming, nonlinear programming and genetic algorithms are fused. The overall formulations of the problem of optimal dimensioning consist of minimizing an objective function constituted through the associated cost of the pipes that form the network. This methodology was implemented in three networks a fictitious irrigation and two irrigation networks (Tuncarta and Cariyacu located in the cities of Loja and Chimborazo which yielded optimal design  solutions. Finally different scenarios were simulated in both models to obtain an overview of the operation of the hydraulic variables

  17. Behaviour Of Saline Irrigation Water Components In Pakistani Barley And Calcareous Soil Under Scheduling Irrigation Using Neutron Scattering Technique

    International Nuclear Information System (INIS)

    RIZK, M.A.

    2010-01-01

    This study aims to investigate the behaviour of cation uptake by Pakistani barley (genotype PK-30163) as affected by saline irrigation water, as well as cation distribution within the soil profile. This experiment was carried out at Soil and Water Research Department, Nuclear Research Centre, Atomic Energy Authority, Inshas, Egypt. The soil was transferred from Wadi Sudr (South Sinai, Egypt). It is salted affected soil (calcareous soil, EC = 4.3 dS/m) and was irrigated using ground water irrigation (12.5 dS/m). Nine used lysimeters were irrigated with three artificial saline water (0.3, 4 and 8 dS/m) using drip irrigation system. The irrigation schedule was carried out using neutron scattering technique according to the hydro physical properties of the soil. Pakistani barley (halophytic plant) was used to remove salts from the soil especially sodium cations. The cation uptake and cation distribution (Na, K, Ca, Mg) within the soil profile were studied.The data indicated that roots of barley collected within 0-15 cm layer showed high cation uptake that made the salt concentrations in this layer low. Sodium uptake ratio was 43, 37 and 47% from total cation uptake by using fresh water (0.3 dS/m), 4 and 8 dS/m, respectively. The maximum uptake for Na, K, Ca and Mg was 20.51, 19.13, 3.98 and 12.81 g/lys at 5.69, 3.05, 6.56 and 4.15 dS/m, respectively. It was found that Pakistani barley preferred Mg uptake rather than Ca uptake.

  18. APPLICATION OF DRIP IRRIGATION ON COTTON PLANT GROWTH (Gossypium sp.

    Directory of Open Access Journals (Sweden)

    Syahruni Thamrin

    2017-12-01

    Full Text Available The condition of cotton planting in South Sulawesi is always constrained in the fulfillment of water. All plant growth stages are not optimal to increase production, so it is necessary to introduce good water management technology, such as through water supply with drip irrigation system. This study aims to analyze the strategy of irrigation management in cotton plants using drip irrigation system. Model of application by designing drip irrigation system and cotton planting on land prepared as demonstration plot. Observations were made in the germination phase and the vegetative phase of the early plants. Based on the result of drip irrigation design, the emitter droplet rate (EDR was 34.266 mm/hour with an operational time of 4.08 min/day. From the observation of cotton growth, it is known that germination time lasted from 6 to 13 days after planting, the average plant height reached 119.66 cm, with the number of leaves averaging 141.93 pieces and the number of bolls averaging 57.16 boll.

  19. Effects of Seven Different Irrigation Techniques on Debris and the ...

    African Journals Online (AJOL)

    2015-09-19

    Sep 19, 2015 ... Aim: Conventional manual irrigation with a syringe and needle remains widely ..... C M A Total C M A Total C M A Total C M A Total C M A Total C M A Total C M A ..... Andrabi SM, Kumar A, Kumar Tewari R, Kumar Mishra S,.

  20. 75 FR 43958 - Turlock Irrigation District and Modesto Irrigation District; Notice of Application for Amendment...

    Science.gov (United States)

    2010-07-27

    ... to the Turlock Irrigation District's Tuolumne Substation; (2) 23-mile-long, 69-kV Don Pedro-Hawkins Line extending from the Don Pedro switchyard to the Turlock Irrigation District's Hawkins Substation...

  1. Optimizing nitrogen-fertilizer application to wheat under irrigation

    International Nuclear Information System (INIS)

    Boaretto, A.E.; Spolidoirio, E.S.; Trivelin, P.C.O.; Muraoka, T.; Freitas, J.G. de; Cantarella, H.

    2000-01-01

    The responses of wheat to urea, its time of application and the fate of the applied N under irrigation were studied over 2 years. Also studied was the recovery of residual N by soybean planted in the same plots. Maximum grain productivity was obtained with 90 kg N ha -1 . Urea-N uptake ranged from 52% for application at sowing, to 85% when applied at tillering. The main loss of fertilizer N occurred as ammonia volatilized, which ranged from 5 to 12%. Loss of N by leaching was less than 1%, even with an application of 135 kg N ha -1 , which is higher than the rate locally recommended for irrigated wheat. The small leaching loss was due to little rainfall during the growing season and irrigation sufficient only to moisten the root zone. The residual N after wheat harvest represented around 40% of that applied: 21% in soil (to a depth of 60 cm), 3% in roots and 16% in the wheat straw. Soybean recovered less than 2% of the N applied to the wheat. (author)

  2. Automation of irrigation systems to control irrigation applications and crop water use efficiency

    Science.gov (United States)

    Agricultural irrigation management to slow water withdrawals from non-replenishing quality water resources is a global endeavor and vital to sustaining irrigated agriculture and dependent rural economies. Research in site-specific irrigation management has shown that water use efficiency, and crop p...

  3. Willingness to pay for more efficient irrigation techniques in the Lake Karla basin, Greece.

    Science.gov (United States)

    Mylopoulos, Nikitas; Fafoutis, Chrysostomos

    2014-05-01

    Thessaly, the second largest plain of Greece, is an intensively cultivated agricultural region. The intense and widespread agriculture of hydrophilic crops, such as cotton, has led to a remarkable water demand increase, which is usually covered by the overexploitation of groundwater resources. The Lake Karla basin is a prominent example of this unsustainable practice. Competition for the limited available freshwater resources in the Lake Karla basin is expected to increase in the near future as demand for irrigation water increases and drought years are expected to increase due to climate change. Together with the Unions of Agricultural Cooperatives, the Local Organizations of Land Reclamation is planning to introduce more efficient, water saving automated drip irrigation in the area among farmers who currently use non-automated drip irrigation, in order to ensure that these farmers can better cope with drought years and that water will be used more efficiently in crop production. Saving water use in irrigated agriculture is expected to be beneficial to both farmers and the restoration of Lake Karla and its wildlife like plants and birds. The aim of this study is to understand and record the farmers' opinions regarding the use of irrigation water and the restoration of Lake Karla, and to extract valuable conclusions and perform detailed analysis of the criteria for a new irrigation method. A general choice experiment with face-to-face interviews was conducted, using a random sample of 150 open field farmers from the study area. The farmers, who use the non-automated drip irrigation method and their farms are located within the watershed of Lake Karla, were interviewed regarding their willingness to switch to more efficient irrigation techniques, such as automated and controlled drip irrigation.The most important benefits of automated drip irrigation are an increase in crop yield, as plants are given water in a more precise way (based on their needs during the

  4. Irrigation water sources and irrigation application methods used by U.S. plant nursery producers

    Science.gov (United States)

    Paudel, Krishna P.; Pandit, Mahesh; Hinson, Roger

    2016-02-01

    We examine irrigation water sources and irrigation methods used by U.S. nursery plant producers using nested multinomial fractional regression models. We use data collected from the National Nursery Survey (2009) to identify effects of different firm and sales characteristics on the fraction of water sources and irrigation methods used. We find that regions, sales of plants types, farm income, and farm age have significant roles in what water source is used. Given the fraction of alternative water sources used, results indicated that use of computer, annual sales, region, and the number of IPM practices adopted play an important role in the choice of irrigation method. Based on the findings from this study, government can provide subsidies to nursery producers in water deficit regions to adopt drip irrigation method or use recycled water or combination of both. Additionally, encouraging farmers to adopt IPM may enhance the use of drip irrigation and recycled water in nursery plant production.

  5. Potency of Gamma ray, Electric Current and Elicitor Application, as a Novel Practical Technique, to Improve Biomass Production and Glycoside Quality for Digitalis purpurea L. Grown in Sandy Soil Irrigated with Brackish Water

    International Nuclear Information System (INIS)

    Bosila, H.A.; Afifi, L.M.A.; Ahmed, T.E.S.

    2012-01-01

    Digitalis purpurea L seeds were treated before sowing with gamma ray (G:0, 2.5, 5, 7.5 KR, and electric current (E:O, 100, 150, 200 mA) then grown in sandy soil irrigated with brackish water (900 ppm) , in splite-splite plot design for 3 replicat (R) at two subsequent seasons , through surface drip irrigation system. Plants at 4- month old and monthly until before flowering were foliar sprayed with MnSO 4 as abiotic elicitor (M :O, 3 ppm). Biomass/ Feddan, percentage of total glycosides and percentage of bioactive glycosides, digitoxin and gitoxin were quantitated. Statistical analysis for the obtained data revealed that G, E and M achieved significant in biomass yield and its quality traits. Moreover, interactions ; GE, GM, EM and GEM achieved synergistic and significant increment for this traits. At such G dose the trait was increased by increasing E dose and M concentration. Hence, G 2.5, 5,7.5 KR E200 mA M3 ppm achieved significant increment, as percent over that of control, in biomass production / Feddan by 22, 29, 32%, total glycoside by 27, 40, 30%, digitoxin 27, 40, 30% for both first and second seasons, respectively. Whereas, increment for gitoxin were 27, 41, 30% at first season and 26, 38, 30% at second season, respectively. Overall, these finding strongly confirm the reliability of GEM as a novel practical technique for overproduction biomass/Fed. and quality improvement bioactive cardiac glycosides, digitoxin and gitoxin in Digitalis purpurea L.

  6. Coordinated research project of the use of nuclear and related techniques in assessment of irrigation schedules of field crops to increase effective use of water in irrigation projects

    International Nuclear Information System (INIS)

    Anac, M.S.; Tuzel, I.H.; Anac, D.

    1995-01-01

    The study aimed at determining the followings; water consumptions. irrigation water requirements of new cotton variety N 84; specific growth stages of cotton which are less sensitive to stress so that the irrigation could be avoided without significant yield decrease; and interactions between deficit irrigation and nitrogen fertilizer use. The experiment was set up with 6 irrigation and three nitrogen fertilizer (0.60 , 120 kg.ha sup -1 ) treatments. The irrigation treatments employed single stress at vegetative, flowering and boll formation stages, in addition to full irrigation, continuous stress and the traditional practice. In stress conditions available soil water depleted to 75 - 80 %, whereas in normal irrigation the depletion was 40 % in 0.90 m. of root zone. In full irrigation treatment 8 irrigations were applied, whereas 3 or 4 irrigations were needed in continuous stress conditions. The number of irrigations were 6 or 7 for other stress treatments. Irrigation water applications varied form 424 to 751 mm. Seasonal ET were ranged between 659 and 899 mm. The highest monthly ET in august for all of the treatments. Daily ET were found to vary from 2.2 to 12.1 mm/day. The seed cotton yields, ky values and yield - N indices have indicated that the vegetative state was more sensitive to water stress. The stress at boll formation stage had slight effects on these parameters. Under limited water resource conditions, vegetative growth period of cotton should be given preference for irrigation, followed by flowering period. Omitting irrigation in boll formation period would result in 4.3 to 9.1 % water savings. Yield changes with respect to N rates showed that high N doses are accompanied by high yields. Nitrogen recoveries either from fertilizers or soil revealed high uptakes in full irrigation conditions. Nitrogen use efficiencies were also high in these conditions. Average of three years put forth that 19% of N in stress conditions and 29% in full irrigation were

  7. Drip and Surface Irrigation Water Use Efficiency of Tomato Crop Using Nuclear Techniques

    International Nuclear Information System (INIS)

    Mellouli, H.J.; Askri, H.; Mougou, R.

    2003-01-01

    Nations in the arid and semi-arid regions, especially the Arab countries, will have to take up an important challenge at the beginning of the 21 st century: increasing food production in order to realise food security for growing population, wile optimising the use of limited water resources. Using and adapting management techniques like the drip irrigation system could obtain the later. This would allow reduction in water losses by bare soil evaporation and deep percolation. Consequently improved water use efficiency could be realised. In this way, this work was conducted as a contribution on the Tunisian national programs on the optimisation of the water use. By mean a field study at Cherfech Experimental Station (30 km from Tunis), the effect of the irrigation system on the water use efficiency (WUE)-by a season tomato crop-was monitored by comparing three treatments receiving equivalent quantities of fertiliser: Fertigation, Drip irrigation and Furrow irrigation. Irrigation was scheduled by mean calculation of the water requirement based on the agro meteorological data, the plant physiological stage and the soil water characteristics (Clay Loam). The plant water consumption (ETR) was determined by using soil water balance method, where rainfall and amount of irrigation water readily measured

  8. Use of infrared thermometer technique in irrigation scheduling of pomegranate (Punica granatum L. plant

    Directory of Open Access Journals (Sweden)

    Begüm TEKELİOĞLU

    2017-06-01

    Full Text Available The main objectives of this study are to assess crop water stress index (CWSI and to determine irrigation schedule of pomegranate using infrared thermometer technique. Treatments with three replications were irrigated every three and six days intervals, as much as 0.50 (S1, 0.75 (S2, 1.00 (S3, and 1.25 (S4 of Class A pan evaporation. Additionally, an unirrigated plot was also formed. The equations obtained for non-water stress baseline is Tc-Ta=0.645VPD-4.338. The equation of full water stressed upper baseline obtained from data taken from branches of pomegranate plant cut in different days is given by Tc-Ta= 0.0489VPD+2.8734. According to the results obtained, it is concluded that infrared thermometer can be used for irrigation scheduling of the pomegranate plants in Antalya conditions. When using this technique in Antalya conditions, it is suggested to keep the seasonal mean CWSI value approximately 0.12 and the index value of 0.40 can be used to start the irrigation. Additionally, it is suggested that the amount of irrigation can be determined as much as the amount of evaporation measured until the index value reaches 0.40.

  9. Effect of Intracanal Cryotherapy and Negative Irrigation Technique on Postendodontic Pain.

    Science.gov (United States)

    Al-Nahlawi, Talal; Hatab, Talaat Abo; Alrazak, Mahmoud Abd; Al-Abdullah, Ahmad

    2016-12-01

    To evaluate the effect of intracanal cryotherapy with negative pressure irrigation (EndoVac) on postendodontic pain after vital single-visit root canal treatment (RCT). A total of 75 single-rooted teeth with single root canal were treated endodontically. After root canal preparation with Protaper Universal rotary system and irrigation, teeth were divided randomly into three groups (n = 25) according to additional irrigation protocol as follows: Group I: No additional irrigation was applied (control); group II: A 20 mL of room temperature saline was irrigated during 5 minutes using EndoVac, and group III: A 20 mL of 2 to 4°C cold saline was irrigated during 5 minutes using EndoVac. Pain levels were assessed by visual analog scale (VAS) and verbal evaluation of pain questionnaire after 6, 12, 24, 48 hours, and 7 days of canal obturation. The data were then analyzed using Statistical Package for the Social Sciences (SPSS) 13.0 using Kruskal-Wallis and Mann-Whitney U tests at p-value of 0.05. The results showed that pain levels were high in groups I and II after 6 hours that decreased with time to almost diminish after 1 week, and on the other hand, group III showed no pain among different monitoring periods. Also pain levels in groups II were lower compared with group I after only 6 hours, with significance p cryotherapy eliminated postendodontic pain clinically. Negative pressure reduced postendodontic pain after 6 hours of treatment. The outcome of this study indicates that the use of intracanal cryotherapy technique with negative pressure irrigation eliminates postendodontic pain after single-visit RCTs.

  10. Effect of irrigation techniques and strategies on water footprint of growing crops

    Science.gov (United States)

    Chukalla, A. D.; Krol, M. S.; Hoekstra, A. Y. Y.

    2014-12-01

    technique. This rank though changes in non-moisture limiting condition (wet year) drip performing better in reducing the WF of growing crops than sub-surface drip. It was observed that with all range of irrigation techniques, strategies and field management practices there is more room in reducing the WF of growing crops in loam than sandy-loam soil.

  11. Solar powered irrigation management using neutron scattering technique

    International Nuclear Information System (INIS)

    Hegazi, A.M.A

    2010-01-01

    This study was conducted to modify a locally assembled solar-powered irrigation system. A direct-coupled photovoltaic pumping system has been assembled and installed in the Egyptian desert in Inshas at the Nuclear Research Center (31 degree 21 ' E, 30 degree 17 ' N). 800 Watt DC motor with brushes was modified to match unsteady PV generator current output. The DC motor was supplied with PV generator current, which was divided between 9 and 4 modules. Pump-set output was tested at different insolation levels and a relationship was carried out from observed data. Hourly solar insolation averages for ten years period were obtained from a program named (Meteo-Norm) software in order to predict and calculate the average daily pumping system water delivery in cubic meters. Preliminary experiment was conducted to acquire a relationship between PVP system outputs and solar-radiation intensity values; which differ from time to time during the day and through different seasons. Solar radiation, power consumption (as Voltage and Current), motor RPM and pump flow varied, while head was kept constant at 4 meter.The system showed trustworthy response to the PV generator output power demonstrated in DC motor RPM and consequently water deliver Based on the obtained results of this study, conclusions are:1.Parameters affecting the performance of solar generator under desert conditions were ambient temperature and contaminants. Focusing on the controllable parameter; dust contaminants; experiments were made to find out the best cleaning period which has limited decrease of the PV output. Results showed that output power was 22% lower for the panel with no cleaning for 20 days. Recommendation is made to do cleaning schedule every three days. 2.Maximizing photovoltaic system efficiency is achieved in order to minimize the initial costs, in other words; more power generated from the PV system unit. These can be obtained by tracking the sun rays through the daytime. Solar tracker was

  12. Optimizing nitrogen fertilizer application to irrigated wheat. Results of a co-ordinated research project. 1994-1998

    International Nuclear Information System (INIS)

    2000-07-01

    This TECDOC summarizes the results of a Co-ordinated Research Project (CRP) on the Use of Nuclear Techniques for Optimizing Fertilizer Application under Irrigated Wheat to Increase the Efficient Use of Nitrogen Fertilizer and Consequently Reduce Environmental Pollution. The project was carried out between 1994 and 1998 through the technical co-ordination of the Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture. Fourteen Member States of the IAEA and FAO carried out a series of field experiments aimed at improving irrigation water and fertilizer-N uptake efficiencies through integrated management of the complex Interactions involving inputs, soils, climate, and wheat cultivars. Its goals were: to investigate various aspects of fertilizer N uptake efficiency of wheat crops under irrigation through an interregional research network involving countries growing large areas of irrigated wheat; to use 15 N and the soil-moisture neutron probe to determine the fate of applied N, to follow water and nitrate movement in the soil, and to determine water balance and water-use efficiency in irrigated wheat cropping systems; to use the data generated to further develop and refine various relationships in the Ceres-Wheat computer simulation model; to use the knowledge generated to produce a N-rate-recommendation package to refine specific management strategies with respect to fertilizer applications and expected yields

  13. Study of seepage losses from irrigation canals using radioactive tracer technique

    International Nuclear Information System (INIS)

    Ahmad, M.; Tariq, J.A.; Rashid, A.; Rafiq, M.; Iqbal, N.

    2004-06-01

    Pakistan has an intricate irrigation system comprising a huge network of canals. A significant fraction of water in irrigation canals is lost through seepage, which is further responsible for water logging and salinity in some areas. Government is considering lining of irrigation canals to overcome this twin menace. Due to involvement of huge costs, highly pervious sections where the seepage rate is appreciably high, are needed to be identified for planning and execution of remedial actions to eliminate or minimize seepage losses. The conventional methods of measuring seepage rate from canals are limited to 'ponding' and 'inflow-outflow' methods. The ponding method is usually restricted to small canals because of the costly bulkheads and water requirement, unaffordable closure of canal, non representation of the line source and variation in the rate of seepage loss with time due to the sealing effects of fine sediments settling out. Inaccurate measurement of discharge under field conditions and complication due to diversion do not favour the inflow-outflow method. It is believed that the analytical methods represent the most accurate and convenient means of determining seepage values using accurate insitu hydraulic conductivity of the subsoil determined by radiotracer, geometry of the canal and position of the groundwater. As a practical application, radiotracer experiments were carried out at Rakh branch canal near Sukhiki, District Hafizabad (Punjab) to determine groundwater filtration velocity by single well point dilution technique using Technetium-99m (sup 99m/Tc) radioactive tracer, Hydraulic conductivity (determined from filtration velocity and hydraulic gradient) and canal parameters were used in the parametric equation of parachute curve to estimate the seepage rate. The average seepage rate was 4.05 cubic meter per day per meter length of the canal (equivalent to 3.795 cusec per million square feet or 1.157 cumec per second per million square meter of

  14. Nuclear techniques to assess irrigation schedules for field crops. Results of a co-ordinated research programme

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-06-01

    This TECDOC summarizes the results of a Co-ordinated Research Programme on The Use of Nuclear and Related Techniques in Assessment of Irrigation Schedules of Field Crops to Increase Effective Use of Water in Irrigation Projects. The programme was carried out between 1990 and 1995 through the technical co-ordination of the Soil Fertility, Irrigation and Crop Production Section of the Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture of the International Atomic Energy Agency. Fourteen Member States of the IAEA and FAO carried out a series of field experiments aimed at improving irrigation water use efficiency through a type of irrigation scheduling known as deficit irrigation. Refs, figs, tabs.

  15. Nuclear techniques to assess irrigation schedules for field crops. Results of a co-ordinated research programme

    International Nuclear Information System (INIS)

    1996-06-01

    This TECDOC summarizes the results of a Co-ordinated Research Programme on The Use of Nuclear and Related Techniques in Assessment of Irrigation Schedules of Field Crops to Increase Effective Use of Water in Irrigation Projects. The programme was carried out between 1990 and 1995 through the technical co-ordination of the Soil Fertility, Irrigation and Crop Production Section of the Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture of the International Atomic Energy Agency. Fourteen Member States of the IAEA and FAO carried out a series of field experiments aimed at improving irrigation water use efficiency through a type of irrigation scheduling known as deficit irrigation. Refs, figs, tabs

  16. Comparison of the removal of calcium hydroxide medicaments on the root canal treatment irrigated with manual and sonic agitation technique

    Directory of Open Access Journals (Sweden)

    Anna Muryani

    2017-11-01

    Full Text Available Introduction: Irrigation of the root canal system is an important part of the endodontic treatment principle which aims to improve the hygiene of the root canal system from any debris and medicament residue with the hydrodynamic system. Root irrigation technique can be done with the manual and sonic system by using 2.5% NaOCI irrigation solution. Calcium hydroxide is used as a medicament for root canal sterilization. Root canal treatment will fail due to the imperfect removal of calcium hydroxide residue. The objective of this research was to analyze the comparison of the removal of calcium hydroxide medicaments on the root canal treatment irrigated with manual and sonic agitation technique using 2.5% sodium hypochlorite solution. Methods: The methods used in this study was experimental laboratory. The sample used was 30 maxillary incisors. The teeth were then divided into two groups randomly, then the root canal preparation was done by the crown down technique with manual irrigation using 2.5% NaOCI solution. The radicular part of the teeth was then split longitudinally, given a standardized groove in the one-third of the apical part, then applied with water-solved calcium hydroxide. The teeth were unified afterwards by using flowable composites, then soaked in the artificial saliva at the temperature of 37ºC. The sample of the 1st group was irrigated by manual agitation technique, and the sample of the 2nd group 2 was irrigated by sonic agitation technique, then both were viewed by stereo microscope. The data results were analyzed by Kruskal-Wallis and Mann-Whitney tests. Results: The results of calcium hydroxide removal were different between the root canals that were irrigated using 2.5% sodium hypochlorite irrigation solution by manual agitation technique compared to the sonic agitation technique. Irrigation using 2.5% sodium hypochlorite irrigation solution with the sonic agitation techniques were proven to be more effective in lifting Ca

  17. Techniques for Wireless Applications

    KAUST Repository

    Gaaloul, Fakhreddine

    2012-05-01

    Switching techniques have been first proposed as a spacial diversity techniques. These techniques have been shown to reduce considerably the processing load while letting multi-antenna systems achieve a specific target performance. In this thesis, we take a different look at the switching schemes by implementing them for different other wireless applications. More specifically, this thesis consists of three main parts, where the first part considers a multiuser environment and an adaptive scheduling algorithm based on the switching with post-selection scheme for statistically independent but non-identically distributed channel conditions. The performance of this switched based scheduler is investigated and a multitude of performance metrics are presented. In a second part, we propose and analyze the performance of three switched-based algorithms for interference reduction in the downlink of over-loaded femtocells. For instance, performance metrics are derived in closed-form and these metrics are used to compare these three proposed schemes. Finally in a third part, a switch based opportunistic channel access scheme is proposed for a cognitive radio system and its performance is analyzed in terms of two new proposed metrics namely the average cognitive radio access and the waiting time duration.

  18. Evaluating two irrigation controllers under subsurface drip irrigated tomato crop

    International Nuclear Information System (INIS)

    Al-Ghobari, H.M.; Mohammad, F.S.; El Marazky, M.S.A.

    2016-01-01

    Smart systems could be used to improve irrigation scheduling and save water under Saudi Arabia’s present water crisis scenario. This study investigated two types of evapotranspiration-based smart irrigation controllers, SmartLine and Hunter Pro-C2, as promising tools for scheduling irrigation and quantifying plants’ water requirements to achieve water savings. The effectiveness of these technologies in reducing the amount of irrigation water was compared with the conventional irrigation scheduling method as a control treatment. The two smart irrigation sensors were used for subsurface irrigation of a tomato crop (cv. Nema) in an arid region. The results showed that the smart controllers significantly reduced the amount of applied water and increased the crop yield. In general, the Hunter Pro-C2 system saved the highest amount of water and produced the highest crop yield, resulting in the highest water irrigation efficiency compared with the SmartLine controller and the traditional irrigation schedule. It can be concluded that the application of advanced scheduling irrigation techniques such as the Hunter controller under arid conditions can realise economic benefits by saving large amounts of irrigation water.

  19. Evaluating two irrigation controllers under subsurface drip irrigated tomato crop

    Energy Technology Data Exchange (ETDEWEB)

    Al-Ghobari, H.M.; Mohammad, F.S.; El Marazky, M.S.A.

    2016-07-01

    Smart systems could be used to improve irrigation scheduling and save water under Saudi Arabia’s present water crisis scenario. This study investigated two types of evapotranspiration-based smart irrigation controllers, SmartLine and Hunter Pro-C2, as promising tools for scheduling irrigation and quantifying plants’ water requirements to achieve water savings. The effectiveness of these technologies in reducing the amount of irrigation water was compared with the conventional irrigation scheduling method as a control treatment. The two smart irrigation sensors were used for subsurface irrigation of a tomato crop (cv. Nema) in an arid region. The results showed that the smart controllers significantly reduced the amount of applied water and increased the crop yield. In general, the Hunter Pro-C2 system saved the highest amount of water and produced the highest crop yield, resulting in the highest water irrigation efficiency compared with the SmartLine controller and the traditional irrigation schedule. It can be concluded that the application of advanced scheduling irrigation techniques such as the Hunter controller under arid conditions can realise economic benefits by saving large amounts of irrigation water.

  20. Simulation of rice yield under different irrigation and nitrogen application managements by CropSyst model

    Directory of Open Access Journals (Sweden)

    Narjes ZARE

    2015-12-01

    Full Text Available The aim of this study was the calibration and validation of CropSyst model for rice in the city of Rasht. The necessary data were extracted from a field experiment which was carried out during 2005-2007 in a split-plot design. The main plots were irrigation regimes including continuous flooding irrigation and 5-day irrigation intervals. The subplots consisted of four nitrogen levels: zero N application, 45, 60 and 75 kg N ha-1. Normalized Root Mean Squared Error (nRMSE and Residual Mass Coefficient (Crm in calibration years were 9.3 % and 0.06, respectively. In validation year, nRMSE and Crm were 9.7 % and 0.11, respectively. According to other indices to assess irrigation regimes and fertilizer levels, the most suitable treatments regarding environmental aspect were 5-day irrigation regime and 45 kg N ha-1.

  1. Wireless sensor network for irrigation application in cotton

    Science.gov (United States)

    A wireless sensor network was deployed in a cotton field to monitor soil water status for irrigation. The network included two systems, a Decagon system and a microcontroller-based system. The Decagon system consists of soil volumetric water-content sensors, wireless data loggers, and a central data...

  2. Effect of irrigation frequency and application levels of sulphur ...

    African Journals Online (AJOL)

    A field experiment was conducted at Indian Agricultural Research Institute, New Delhi during the crop season of 2007 to 2008 and 2008 to 2009 to study the effect of irrigation and sulphur on yield and water use efficiency of Indian mustard (Brassica juncea var. PusaJagannath). The experiment was carried out in split plot ...

  3. Multivariate analysis of the cleaning efficacy of different final irrigation techniques in the canal and isthmus of mandibular posterior teeth

    Directory of Open Access Journals (Sweden)

    Yeon-Jee Yoo

    2013-08-01

    Full Text Available Objectives The aim of this study was to compare the cleaning efficacy of different final irrigation regimens in canal and isthmus of mandibular molars, and to evaluate the influence of related variables on cleaning efficacy of the irrigation systems. Materials and Methods Mesial root canals from 60 mandibular molars were prepared and divided into 4 experimental groups according to the final irrigation technique: Group C, syringe irrigation; Group U, ultrasonics activation; Group SC, VPro StreamClean irrigation; Group EV, EndoVac irrigation. Cross-sections at 1, 3 and 5 mm levels from the apex were examined to calculate remaining debris area in the canal and isthmus spaces. Statistical analysis was completed by using Kruskal-Wallis test and Mann-Whitney U test for comparison among groups, and multivariate linear analysis to identify the significant variables (regular replenishment of irrigant, vapor lock management, and ultrasonic activation of irrigant affecting the cleaning efficacy of the experimental groups. Results Group SC and EV showed significantly higher canal cleanliness values than group C and U at 1 mm level (p < 0.05, and higher isthmus cleanliness values than group U at 3 mm and all levels of group C (p < 0.05. Multivariate linear regression analysis demonstrated that all variables had independent positive correlation at 1 mm level of canal and at all levels of isthmus with statistical significances. Conclusions Both VPro StreamClean and EndoVac system showed favorable result as final irrigation regimens for cleaning debris in the complicated root canal system having curved canal and/or isthmus. The debridement of the isthmi significantly depends on the variables rather than the canals.

  4. Nuclear Techniques in Agriculture: Status and Applications

    International Nuclear Information System (INIS)

    Kurdali, F.

    2007-01-01

    This paper is focused on the role of nuclear techniques and their applications in agriculture science for plant and animal production, and to study the relationships among soil, plant, air, water, nutrients and agricultural pests. For example, carbon isotope discrimination 12 C/ 13 C can be used to select appropriate plant genotypes which are tolerant to drought and salinity stress. Using 15 N to study, symbiotic N 2 fixation, inorganic N dynamics in the soil, plant system, mineralization of organic N in soils, efficient use of chemical and organic N fertilizers and microbial protein production in ruminants. Neutron gauges are used for soil moisture measurements to assess crop water use efficiencies, crops water requirements, and irrigation scheduling for conventional and new methods of irrigation. The use of environmental isotopes ( 18 O, 2 H, 3 H and 14 C) in hydrology; and 137 Cs to study soil erosion. Using 32 P to study the fate of applied P fertilizers (chemical fractionation and availability), their use efficiency and phosphorus metabolism in animals. Ionizing radiation is used to improve the quality and productivity of major crops, to induce mutations, to improve the metabolisable and digestible energy of unconventional feeds and the nutritive value of agricultural residues, and to protect crops against agricultural pests and in food conservation. Radioimmunoassay is used in studies to improve the production and reproductive performance of indigenous small ruminants. (author)

  5. ELECTROSPRAY, TECHNIQUE AND APPLICATIONS

    NARCIS (Netherlands)

    BRUINS, AP

    Electrospray makes use of ions present in electrically charged droplets in an aerosol. The generation of an aerosol by electrospray has already been published by Zeleny in 1917. The feasibility of electrospray as an ionization technique was demonstrated by Fenn and coworkers, and by a group of

  6. The Use of Different Irrigation Techniques to Decrease Bacterial Loads in Healthy and Diabetic Patients with Asymptomatic Apical Periodontitis.

    Science.gov (United States)

    Ghoneim, Mai; Saber, Shehab ElDin; El-Badry, Tarek; Obeid, Maram; Hassib, Nehal

    2016-12-15

    Diabetes mellitus is a multisystem disease which weakens the human's immunity. Subsequently, it worsens the sequelae of apical periodontitis by raising a fierce bacterial trait due to the impaired host response. This study aimed to estimate bacterial reduction after using different irrigation techniques in systemically healthy and diabetic patients with asymptomatic apical periodontitis. Enterococcus faecalis , Peptostreptococcus micros , and Fusobacterium necleatum bacteria were chosen, as they are the most common and prevailing strains found in periodontitis. Bacterial samples were retrieved from necrotic root canals of systemically healthy and diabetic patients, before and after endodontic cleaning and shaping by using two different irrigation techniques; the conventional one and the EndoVac system. Quantitive polymerase chain reaction (qPCR) was utilised to detect the reduction in the bacterial count. The EndoVac irrigation system was effective in reducing bacteria, especially Peptostreptococcus micros in the diabetic group when compared to conventional irrigation technique with a statistically significant difference. The EndoVac can be considered as a promising tool in combination with irrigant solution to defeat the bacterial colonies living in the root canal system. Additional studies ought to be done to improve the means of bacterial clearance mainly in immune-compromised individuals.

  7. Assessment of the soil water balance by the combination of cosmic ray neutron sensing and eddy covariance technique in an irrigated citrus orchard (Marrakesh, Morocco)

    Science.gov (United States)

    Mroos, Katja; Baroni, Gabriele; Er-Raki, Salah; Francke, Till; Khabba, Said; Jarlan, Lionel; Hanich, Lahoucine; Oswald, Sascha E.

    2014-05-01

    Irrigation water requirement plays a crucial role in many agricultural areas and especially in arid and semi-arid landscapes. Improvements in the water management and the performance of the irrigation systems require a correct evaluation of the hydrological processes involved. However, some difficulties can arise due to the heterogeneity of the soil-plant system and of the irrigation scheme. To overcome these limitations, in this study, the soil water balance is analyzed by the combination of the Eddy Covariance technique (EC) and Cosmic Ray neutron Sensing (CRS). EC provides the measurement of the actual evapotranspiration over the area as it was presented in many field conditions. Moreover CRS showed to be a valuable approach to measure the root zone soil moisture integrated in a footprint of ~30 ha. In this way, the combination of the two methodologies should provide a better analysis of the soil water balance at field scale, as opposed to point observations, e.g. by TDR, evaporimeter and fluxmeter. Then, this could increase the capability to assess the irrigation efficiency and the agricultural water management. The study is conducted in a citrus orchard situated in a semi-arid region, 30 km southwest of Marrakesh (Morocco). The site is flat and planted with trees of same age growing in parallel rows with drip irrigation lines and application of fertilizer and pesticides. The original soil seems modified on the surface by the agricultural use, creating differences between trees, rows and lines. In addition, the drip irrigation creates also a spatial variability of the water flux distribution in the field, making this site an interesting area to test the methodology. Particular attention is given to the adaptation of the standard soil sampling campaign used for the calibration of the CRS and the introduction of a weighing function. Data were collected from June to December 2013, which corresponds to the high plant transpiration. Despite the intention of the

  8. Physiological and biochemical characterization of mango tree with paclobutrazol application via irrigation

    Directory of Open Access Journals (Sweden)

    Moisés Alves de Souza

    2016-12-01

    Full Text Available Paclobutrazol application in mango tree floral induction is followed by changes in the hormonal balance and carbohydrates production. This study aimed at evaluating the physiological and biochemical variables of mango tree (Palmer cultivar by applying paclobutrazol doses via irrigation. The experimental design was randomized blocks, with five paclobutrazol doses (0.7 g, 1.0 g, 1.3 g, 1.6 g and 1.9 g of a.i. per linear meter of canopy and one additional treatment, with one dose in the conventional form of application (1.9 g of a.i. per linear meter of canopy, and four replicates. The variables analyzed were: photosynthesis rate; stomatal conductance; transpiration; leaf temperature; CO2 ratio; total protein content; reducing, non-reducing and total soluble sugars in leaf tissue and fruit; and nitrate reductase enzyme. The lowest values for photosynthesis rate and stomatal conductance were obtained with paclobutrazol applied via irrigation. The highest values for gas exchange were obtained with the lowest paclobutrazol doses applied via irrigation, showing that this kind of application is efficient and that it is possible to reduce the application dose via irrigation system. The highest carbohydrate contents in the leaf tissue were observed for the doses of 1.06 g and 1.09 g of a.i. per linear meter of canopy, applied via irrigation. The carbohydrate contents in fruits decreased in response to the paclobutrazol dose. The application methods and doses applied via irrigation did not influence the nitrate reductase activity.

  9. Assessment of linear anionic polyacrylamide application to irrigation canals for seepage control

    Directory of Open Access Journals (Sweden)

    Hamil Uribe

    2013-09-01

    Full Text Available South- central area of Chile area has a Mediterranean climate and high crop water requirements. Irrigation water is distributed through long channels which have low water conveyance efficiency (Ec, difficult to improve by conventional techniques. The objective of this study was to quantify Ec and to evaluate the use of Linear Anionic Polyacrylamide (LA-PAM to reduce seepage losses. The study was carried out in south-central area of Chile, (UTM Coordinate N 5745000; E 725000 m, datum is WGS-84, zone 18S in 250 km of channels whose flow varied between 0.12 and 24.6 m3 s–1. Water users indicated channel reaches with potential low Ec, which were selected for LA-PAM application. In 11 reaches between 0.51 and 3 km in length, 1 to 3 LAPAM applications were performed at rates of 10 kg ha–1, considering the wet perimeter area as basis of calculation. Thirty-one LA-PAM applications were performed over a 30.5 km length. Most of the channels were large enough to allow motorboat moving against the current to carry-out LA-PAM application. Water flow was measured (StreamPro ADCP at both ends of selected reaches before and after granular LAPAM application. Weekly measurements were made to quantify treatment effect duration. Water turbidity and temperature were measured. Channels showed variable Ec from 87% to 94%. Two reaches showed 6% water gains. In more than 80% cases LA-PAM effect was positive, achieving loss reductions of 15 to 760 L s–1. In other cases LA-PAM had a negative effect since it mainly affected water entry into the channel. It was determined that field conditions referred by users as indicators of Ec are not always correct and vary in time according to climatic conditions. Ec was estimated and it was possible to reduce seepage through LA-PAM applications. This allow increasing irrigation security in critical periods, especially under drought conditions.

  10. Effect of Instrumentation Techniques, Irrigant Solutions and Artificial accelerated Aging on Fiberglass Post Bond Strength to Intraradicular Dentin.

    Science.gov (United States)

    Santana, Fernanda Ribeiro; Soares, Carlos José; Silva, Júlio Almeida; Alencar, Ana Helena Gonçalves; Renovato, Sara Rodrigues; Lopes, Lawrence Gonzaga; Estrela, Carlos

    2015-07-01

    To evaluate the effect of instrumentation techniques, irrigant solutions and specimen aging on fiberglass posts bond strength to intraradicular dentine. A total of 120 bovine teeth were prepared and randomized into control and experimental groups resulting from three study factors (instrumentation techniques, irrigant solutions, specimen aging). Posts were cemented with RelyX U100. Samples were submitted to push-out test and failure mode was evaluated under a confocal microscope. In specimens submitted to water artificial aging, nickel-titanium rotary instruments group presented higher bond strength values in apical third irrigated with NaOCl or chlorhexi-dine. Irrigation with NaOCl resulted in higher bond strength than ozonated water. Artificial aging resulted in significant bond strength increase. Adhesive cement-dentin failure was prevalent in all the groups. Root canal preparation with NiTi instruments associated with NaOCl irrigation and ethylenediaminetetra acetic acid (EDTA) increased bond strength of fiberglass posts cemented with self-adhesive resin cement to intraradicular dentine. Water artificial aging significantly increased post-Clinical significance: The understanding of factors that may influence the optimal bond between post-cement and cement-dentin are essential to the success of endodontically treated tooth restoration.

  11. Bridging Mediterranean cultures in the IYS: A documentary exhibition on irrigation techniques in water scarcity conditions

    Science.gov (United States)

    Barontini, Stefano; Louki, Amina; Ben Slima, Zied; Ezzahra Ghaouch, Fatima; Labaran, Raisa; Raffelli, Giulia; Peli, Marco; Vitale, Nicola

    2015-04-01

    Brescia, an industrial city in Northern Italy, is now experiencing a crucial change in its traditional structure. In recent years in fact it has been elected as living and working seat by many foreigners and it is now one of the cities with the greatest percentage of migrants in the Country. This is an important challenge for the city and an opportunity to merge, compare and integrate different cultures to build its future. In this context some students of different Courses (engineering and medicine), belonging both to the Arabian and local community, met together and with researchers in the study team 'Al-B¯i r¯u n¯i , for culture, science and society'. The team aims at organising cultural events in which, starting from the figure of the Persian scientist Ab¯u Raih. ¯a n Al-B¯i r¯u n¯i (about 973, 1051), the contribution of the Arabian and Islamic culture to the development of the European one in the middle ages is investigated. Moving from the initial idea of the study team Al-B¯i r¯u n¯i and from the suggestions of the World Soil Day 2014 and of the International Year of Soils 2015, we built a documentary exhibition entitled 'Irrigation techniques in water scarcity conditions'. The exhibition, which stresses the importance of the irrigation techniques for the soil conservation, is focused on the idea of disseminating two main concepts, i.e. (1) the technological continuity of some water supply systems in countries, around the Mediterranean Sea, affected by similar conditions of water availability, and (2) the possibility of building environments where, due to severe or extreme climatic conditions, the sustainability is reached when the man lives in equilibrium with the nature. The exhibition, which is written in Italian and will move around in the city during all 2015, consists of about twenty posters organized into three main chapters, corresponding to three main classes of water supply systems which are common in most of the countries surrounding

  12. The traditional irrigation technique of Lake Garda lemon--houses (Northern Italy)

    Science.gov (United States)

    Barontini, Stefano; Vitale, Nicola; Fausti, Federico; Bettoni, Barbara; Bonati, Sara; Peli, Marco; Pietta, Antonella; Tononi, Marco; Ranzi, Roberto

    2016-04-01

    Between 16th and 19th centuries the North-Western side of Lake Garda was seat of an important district which, at the time of its maximum splendour between 18th and 19th centuries, produced and exported lemons and citrus even toward the Northern Europe and the Russia. The limonaie del Garda (Lake-Garda lemon-houses), the local name of the citrus orchards, were settled on terraces built on steep slopes, with landfill taken from the Eastern side of the lake, and closed by greenhouses during late autumn and winter in order to protect the cultivations. The terraces were built nearby streams, they were South-Eastern exposed and protected by walls from the cold winds. Thanks in fact to the Lake Garda microclimate, lemon trees were not cultivated in pots, as in the typical orangeries of mid-latitudes Europe, but directly in the soil. Here the citrus cultivation technique reached a remarkably high degree of standardisation, with local cultivar as the Madernino or lemon from Maderno, and it involved, as in modern industrial districts, all the surrounding land in order to satisfy the needing of required materials to build the terraces, the walls, the greenhouses and the wooden frames to hold the branches laden with fruits. Due to the great water requirement of lemon trees during summer, which is estimated to range from 150 to 300 ℓ every ten days, the water management played a key role in the cultivation technique. The traditional irrigation technique was standardized as well. During our surveys, we observed that most of the lemon-houses still conserve little stone flumes along the walls upslope to the terraces, with spillways every adult tree, i.e. about every 4 m. The flumes were filled with water taken from an upstream reservoir, built nearby a stream. The spillways were activated with a backwater obtained by means of a sand bag placed within the flume, just downstream to the spillway itself. In order to avoid any excavation, spilled water was driven to the base of each

  13. AgIIS, Agricultural Irrigation Imaging System, design and application

    Science.gov (United States)

    Haberland, Julio Andres

    Remote sensing is a tool that is increasingly used in agriculture for crop management purposes. A ground-based remote sensing data acquisition system was designed, constructed, and implemented to collect high spatial and temporal resolution data in irrigated agriculture. The system was composed of a rail that mounts on a linear move irrigation machine, and a small cart that runs back and forth on the rail. The cart was equipped with a sensors package that measured reflectance in four discrete wavelengths (550 nm, 660 nm, 720 nm, and 810 nm, all 10 nm bandwidth) and an infrared thermometer. A global positioning system and triggers on the rail indicated cart position. The data was postprocessed in order to generate vegetation maps, N and water status maps and other indices relevant for site-specific crop management. A geographic information system (GIS) was used to generate images of the field on any desired day. The system was named AgIIS (A&barbelow;gricultural I&barbelow;rrigation I&barbelow;maging S&barbelow;ystem). This ground based remote sensing acquisition system was developed at the Agricultural and Biosystems Engineering Department at the University of Arizona in conjunction with the U.S. Water Conservation Laboratory in Phoenix, as part of a cooperative study primarily funded by the Idaho National Environmental and Engineering Laboratory. A second phase of the study utilized data acquired with AgIIS during the 1999 cotton growing season to model petiole nitrate (PNO3 -) and total leaf N. A latin square experimental design with optimal and low water and optimal and low N was used to evaluate N status under water and no water stress conditions. Multivariable models were generated with neural networks (NN) and multilinear regression (MLR). Single variable models were generated from chlorophyll meter readings (SPAD) and from the Canopy Chlorophyll Content Index (CCCI). All models were evaluated against observed PNO3- and total leaf N levels. The NN models

  14. 76 FR 12720 - City of Escondido, CA, and Vista Irrigation District; Notice of Application Accepted for Filing...

    Science.gov (United States)

    2011-03-08

    ..., CA, and Vista Irrigation District; Notice of Application Accepted for Filing, Ready for Environmental...: City of Escondido, California (Escondido) and Vista Irrigation District (Vista). e. Name of Project... owned by the La Jolla, San Pasqual, and Rincon Indian Tribes. g. Filed Pursuant to: Federal Power Act...

  15. Novel radar techniques and applications

    CERN Document Server

    Klemm, Richard; Lombardo, Pierfrancesco; Nickel, Ulrich

    2017-01-01

    Novel Radar Techniques and Applications presents the state-of-the-art in advanced radar, with emphasis on ongoing novel research and development and contributions from an international team of leading radar experts. This volume covers: Real aperture array radar; Imaging radar and Passive and multistatic radar.

  16. Novel radar techniques and applications

    CERN Document Server

    Klemm, Richard; Koch, Wolfgang

    2017-01-01

    Novel Radar Techniques and Applications presents the state-of-the-art in advanced radar, with emphasis on ongoing novel research and development and contributions from an international team of leading radar experts. This volume covers: Waveform diversity and cognitive radar and Target tracking and data fusion.

  17. The Use of Different Irrigation Techniques to Decrease Bacterial Loads in Healthy and Diabetic Patients with Asymptomatic Apical Periodontitis

    OpenAIRE

    Ghoneim, Mai; Saber, Shehab ElDin; El-Badry, Tarek; Obeid, Maram; Hassib, Nehal

    2016-01-01

    BACKGROUND: Diabetes mellitus is a multisystem disease which weakens the human’s immunity. Subsequently, it worsens the sequelae of apical periodontitis by raising a fierce bacterial trait due to the impaired host response. AIM: The study aimed to estimate bacterial reduction after using different irrigation techniques in systemically healthy and diabetic patients with asymptomatic apical periodontitis. MATERIAL AND METHODS: Enterococcus faecalis, Peptostreptococcus micros, and Fusoba...

  18. Dealing with drought in irrigated agriculture through insurance schemes: an application to an irrigation district in Southern Spain

    Energy Technology Data Exchange (ETDEWEB)

    Ruiz, M.; Bielza, J.; Garrido, A.; Iglesias, A.

    2015-07-01

    Hydrological drought is expected to have an increasing impact on both crop and fruit yields in arid and semi-arid regions. Some existing crop insurance schemes provide coverage against water deficits in rain-fed agriculture. The Prevented Planting Program in the USA covers against drought for irrigated agriculture. However, drought insurance for irrigated agriculture is still a challenge for companies and institutions because of the complexity of the design and implementation of this type of insurance. Few studies have attempted to evaluate the risk of loss due to irrigation water scarcity using both stand-alone production functions and crop simulation models. This paper’s contributions are that it evaluates the suitability of AquaCrop for calculating drought insurance premiums for irrigated agriculture and that it discusses contract conditions and insurance design for hydrological drought risk coverage as part of a traditional insurance product, with on-field loss assessment in combination with a trigger index. This method was applied to an irrigation district in southern Spain. Our insurance premium calculation showed that it is feasible to apply this method provided that its data requirements are met, such as a large enough set of reliable small-scale yield and irrigation time series data, especially soil data, to calibrate AquaCrop. The choice of a trigger index should not be underestimated because it proved to have a decisive influence on insurance premiums and indemnities. Our discussion of the contract conditions shows that hydrological drought insurance must comply with a series of constraints in order to avoid moral hazard and basis risk. (Author)

  19. Dealing with drought in irrigated agriculture through insurance schemes: an application to an irrigation district in Southern Spain

    Directory of Open Access Journals (Sweden)

    Jorge Ruiz

    2015-12-01

    Full Text Available Hydrological drought is expected to have an increasing impact on both crop and fruit yields in arid and semi-arid regions. Some existing crop insurance schemes provide coverage against water deficits in rain-fed agriculture. The Prevented Planting Program in the USA covers against drought for irrigated agriculture. However, drought insurance for irrigated agriculture is still a challenge for companies and institutions because of the complexity of the design and implementation of this type of insurance. Few studies have attempted to evaluate the risk of loss due to irrigation water scarcity using both stand-alone production functions and crop simulation models. This paper’s contributions are that it evaluates the suitability of AquaCrop for calculating drought insurance premiums for irrigated agriculture and that it discusses contract conditions and insurance design for hydrological drought risk coverage as part of a traditional insurance product, with on-field loss assessment in combination with a trigger index. This method was applied to an irrigation district in southern Spain. Our insurance premium calculation showed that it is feasible to apply this method provided that its data requirements are met, such as a large enough set of reliable small-scale yield and irrigation time series data, especially soil data, to calibrate AquaCrop. The choice of a trigger index should not be underestimated because it proved to have a decisive influence on insurance premiums and indemnities. Our discussion of the contract conditions shows that hydrological drought insurance must comply with a series of constraints in order to avoid moral hazard and basis risk.

  20. Applications of Satellite Data to Support Improvements in Irrigation and Groundwater Management in California

    Science.gov (United States)

    Melton, F. S.; Huntington, J. L.; Johnson, L.; Guzman, A.; Morton, C.; Zaragoza, I.; Dexter, J.; Rosevelt, C.; Michaelis, A.; Nemani, R. R.; Cahn, M.; Temesgen, B.; Trezza, R.; Frame, K.; Eching, S.; Grimm, R.; Hall, M.

    2017-12-01

    In agricultural regions around the world, threats to water supplies from drought and groundwater depletion are driving increased demand for tools to advance agricultural water use efficiency and support sustainable groundwater management. Satellite mapping of evapotranspiration (ET) from irrigated agricultural lands can provide agricultural producers and water resource managers with information that can be used to both optimize ag water use and improve estimates of groundwater withdrawals for irrigation. We describe the development of two remote sensing-based tools for ET mapping in California, including important lessons in terms of system design, partnership development, and transition to operations. For irrigation management, the integration of satellite data and surface sensor networks to provide timely delivery of information on crop water requirements can make irrigation scheduling more practical, convenient, and accurate. Developed through a partnership between NASA and the CA Department of Water Resources, the Satellite Irrigation Management Support (SIMS) framework integrates satellite data with information from agricultural weather networks to map crop canopy development and crop water requirements at the scale of individual fields. Information is distributed to agricultural producers and water managers via a web-based interface and web data services. SIMS also provides an API that facilitates integration with other irrigation decision support tools, such as CropManage and IrriQuest. Field trials using these integrated tools have shown that they can be used to sustain yields while improving water use efficiency and nutrient management. For sustainable groundwater management, the combination of satellite-derived estimates of ET and data on surface water deliveries for irrigation can increase the accuracy of estimates of groundwater pumping. We are developing an OpenET platform to facilitate access to ET data from multiple models and accelerate operational

  1. Behavior, balance and distribution of sediments within irrigation systems. Application to Pakistan

    International Nuclear Information System (INIS)

    Vabre, Alexandre

    2000-01-01

    This PhD work is part of a research program between Cemagref, CEA and IWMI. It aims at studying the sediment deposition phenomena in irrigation Systems of Pakistan. Indeed, many Systems are subject to an excessive sediment deposition that widely disturbs their functioning. A pragmatic approach of the problem is chosen, and the sediment deposition description is realized through global methods. This choice is done in order to allow the developed methods and tools to be utilized directly by the irrigation managers. A global numerical modeling method (GSM) is proposed. It lies on classical laws of sediment transport but a new formalism is proposed for the expression of the deposition. It's a relationship between the sediment trapping efficiency of a reach and its sediment transport capacity. Also, criteria are defined for the definition of homogeneous reaches in the system. An outline of GSM is implemented on a sediment deposition data set of an actual System in Pakistan (Jamrao). A measurement campaign using radio-activable tracers is then carried out on this site to complete the GSM working data set Also, such a campaign with it only is a description method of the deposition phenomena in the irrigation System. The strength of the modeling approach laws is then tested on another case study of irrigation System in Pakistan (Chashma). The results are very much encouraging because the GSM model could be calibrated and validated on several actual deposition trends with quite moderate errors for such a tool. Also, the constituted data set from the tracer campaign was found minimum and sufficient to implement the GSM. Moreover, it has been possible to use the GSM for irrigation management applications. A design criterion for stable canals is proposed. And the GSM has allowed to identify an hydraulic operational scenario on an irrigation System that decreases the deposition. The perspectives of this work are to test the GSM approach on other data sets and then to

  2. Multimedia watermarking techniques and applications

    CERN Document Server

    Kirovski, Darko

    2006-01-01

    Intellectual property owners must continually exploit new ways of reproducing, distributing, and marketing their products. However, the threat of piracy looms as a major problem with digital distribution and storage technologies. Multimedia Watermarking Techniques and Applications covers all current and future trends in the design of modern systems that use watermarking to protect multimedia content. Containing the works of contributing authors who are worldwide experts in the field, this volume is intended for researchers and practitioners, as well as for those who want a broad understanding

  3. Peripheral Atherectomy: Applications and Techniques.

    Science.gov (United States)

    Mittleider, Derek; Russell, Erich

    2016-06-01

    Peripheral atherectomy is a class of procedures that is rapidly increasing in volume. Multiple classes of devices exist, and newer variants are added to the market annually. The devices see wide application for de novo lesions, in-stent restenosis, and adjunctive therapy for drug-coated balloons. The body of evidence supporting atherectomy is less robust than for many other peripheral therapies. The frequency and severity of complications from atherectomy can be significant compared with angioplasty and stenting, and familiarity with preventative and bailout techniques is essential for the interventionalist. Copyright © 2016 Elsevier Inc. All rights reserved.

  4. Neutron radiography, techniques and applications

    International Nuclear Information System (INIS)

    Domanus, J.C.

    1987-10-01

    After describing the principles of the ''in pool'' and ''dry'' installations, techniques used in neutron radiography are reviewed. Use of converter foils with silver halide films for the direct and transfer methods is described. Advantages of the use of nitrocellulose film for radiographying radioactive objects are discussed. Dynamic imaging is shortly reviewed. Standardization in the field of neutron radiography (ASTM and Euratom Neutron Radiography Working Group) is described. The paper reviews main fields of use of neutron radiography. Possibilities of use of neutron radiography at research reactors in various scientific, industrial and other fields are mentioned. Examples are given of application of neutron radiography in industry and the nuclear field. (author)

  5. Raman Imaging Techniques and Applications

    CERN Document Server

    2012-01-01

    Raman imaging has long been used to probe the chemical nature of a sample, providing information on molecular orientation, symmetry and structure with sub-micron spatial resolution. Recent technical developments have pushed the limits of micro-Raman microscopy, enabling the acquisition of Raman spectra with unprecedented speed, and opening a pathway to fast chemical imaging for many applications from material science and semiconductors to pharmaceutical drug development and cell biology, and even art and forensic science. The promise of tip-enhanced raman spectroscopy (TERS) and near-field techniques is pushing the envelope even further by breaking the limit of diffraction and enabling nano-Raman microscopy.

  6. DEFICIT IRRIGATION TECHNIQUE FOR REDUCING WATER USE OF TOMATO UNDER POLYTUNNEL CONDITIONS

    Directory of Open Access Journals (Sweden)

    Sladjana SAVIC

    2012-01-01

    Full Text Available The aim of paper was to asses the use of regulated deficit irrigation (RDI for production of two tomato cultivars (Cedrico and Abellus in polytunnels in Serbia. RDI plants received 60% of the water that was applied to FI plants and significant saving of water for irrigation and increased in irrigation water use efficiency (IWUE were achieved. Yield data for Cedrico cultivar showed no differences between RDI and FI, while due to the bigger sensitivity to drought, yield of Abellus was reduced under RDI. In general, fruit quality (soluble solids, titrable acidity was sustained or improved in both cultivars under RDI. Economic analyses showed that due to the current low prices of water and electricity in Serbia, the profit increase of Cedrico, similarly to the previously trialed cultivar Amati, was not high under RDI comparing to FI. Reduction of yield and consequent profit for Abellus, indicated that for future commercial growing of tomato under RDI should be used drought resistant cultivars.

  7. Physiological and biochemical characterization of mango tree with paclobutrazol application via irrigation.

    OpenAIRE

    SOUZA, M. A. de; MESQUITA, A. C.; SIMOES, W. L.; FERREITA, K. M.; ARAÚJO, E. F. J.

    2017-01-01

    Paclobutrazol application in mango tree floral induction is followed by changes in the hormonal balance and carbohydrates production. This study aimed at evaluating the physiological and biochemical variables of mango tree (Palmer cultivar) by applying paclobutrazol doses via irrigation. The experimental design was randomized blocks, with five paclobutrazol doses (0.7 g, 1.0 g, 1.3 g, 1.6 g and 1.9 g of a.i. per linear meter of canopy) and one additional treatment, with one dose in the conven...

  8. Ex vivo evaluation of various instrumentation techniques and irrigants in reducing E. faecalis within root canals.

    Science.gov (United States)

    Basmaci, F; Oztan, M D; Kiyan, M

    2013-09-01

    To evaluate ex vivo the effectiveness of single-file instrumentation techniques compared with serial Ni-Ti rotary instrumentation with several irrigation regimens in reducing E. faecalis within root canals. A total of 81 extracted human mandibular premolar teeth with a single root canal were infected with E. faecalis before and after canal preparation. Samples were divided randomly into 9 groups, as follows: group 1-A: sterile phosphate-buffered saline + Self-adjusting file, group 1-B: 5% sodium hypochlorite + 15% EDTA + Self-adjusting file, group 1-C: 5% sodium hypochlorite + 7% maleic acid + Self-adjusting file, group 2-A: sterile phosphate-buffered saline + Reciproc (R25), group 2-B: 5% sodium hypochlorite + 15% EDTA + Reciproc (R25), group 2-C: 5% sodium hypochlorite + 7% maleic acid + Reciproc (R25), group 3-A: sterile phosphate-buffered saline + ProTaper, group 3-B: 5% sodium hypochlorite + 15% EDTA + ProTaper, group 3-C: 5% sodium hypochlorite + 7% maleic acid + ProTaper. anova was used to analyse statistically the differences in terms of reduction in colony counts between the groups, and Dunn's post hoc test was used for multiple comparisons. All techniques and irrigation regimens significantly reduced the number of bacterial cells in the root canal (P irrigants. © 2013 International Endodontic Journal. Published by John Wiley & Sons Ltd.

  9. Yields of cotton and other crops as affected by applications of sulfuric acid in irrigation water

    Energy Technology Data Exchange (ETDEWEB)

    Christensen, P.D.; Lyerly, P.J.

    1954-01-01

    Effects of sulfuric acid on crop yields and on some physical and chemical properties of a calcareous soil were investigated in a field experiment from 1947 through 1952. On cotton plots, the treatments consisted of applications of irrigation water containing no acid (pH 8.3), water acidified to pH 6, and water acidified to pH 2.3. Cotton was grown five seasons followed by sesbania the sixth season. A test on alfalfa was established using irrigation water not acidified and water acidifeid to pH 4. Alfalfa was grown for 3 years. The fourth year the alfalfa was plowed under and a crop of corn was raised. Cotton yields on the acid plots relative to the checks became progressively higher (with two exceptions) from one year to the next; however, in only one year (1950) were differences in yield statistically significant. With sesbania following cotton, highly significant yield increases resulted from the high acid treatment. Alfalfa yields on the acid plots became progressively greater relative to the non-acid plots, but yield differences were not significant. In cotton leaves, the acid treatments resulted in increased uptake of magnesium, sulfur, and phosphorus, but the increases were probably not significant. Uptake of sodium, potassium, calcium, manganese, and iron were not appreciably affected. In sesbania, the acid treatments did not significantly alter the uptake of any of the plant nutrients determined. There was some indication, however, that the uptake of sodium and iron was reduced by the acidification. The results of this study support the view that soil acidification on calcareous soils may improve the soil physical conditions and result in increased yields, particularly in some crops. The application of acid in the irrigation water did not prove to be economically feasible. 12 references, 1 figure, 7 tables.

  10. Field application of self-healing concrete with natural fibres as linings for irrigation canals in Ecuador

    NARCIS (Netherlands)

    Sierra Beltran, M.G.; Jonkers, H.M.; Mors, R.M.; Mera-Ortiz, W.

    2015-01-01

    This paper describes the first field application of self-healing concrete with alkaliphilic spore-forming bacteria and reinforced with natural fibres. The application took place in the highlands in Ecuador in July 2014. The concrete was cast as linings for an irrigation canal that transports water

  11. Effect of Timing of Potassium Application on Millet (Setaria italica Yield and Grain Protein Content in Different Irrigation Regimes

    Directory of Open Access Journals (Sweden)

    A. Hayati

    2011-05-01

    Full Text Available The research on reducing the water consumption in conventional cropping system is one of the important strategies to improve the water use efficiency in agriculture. In order to investigate the effect of time of potassium application under different irrigation regimes on millet grain yield and protein percent, a field experiment was carried out in Agricultural Research Center of Yasuj, Iran, in 2009. The experiment was conducted as split plot design in a randomized complete blocks design with 3 replications. Irrigation regime included 7, 14 and 21-day intervals as main factor and sub-plots included time of potassium fertilizer application in four stages: planting, tillering, stem development and flowering. The results showed that the effect of irrigation interval was significant on 1000-seed weight, grain and biological yield, number of grains per spike, harvest index, protein content, and chlorophyll a, b and total of leaves. By increasing the irrigation interval, all the above-mentioned traits decreased, except the protein percent that increased. The 1000-seed weight, grain and biological yield, harvest index and protein content were affected significantly by the time of potassium application. Maximum grain yield was obtained by interaction of 7- day irrigation interval and potassium application at the stem development stage. Maximum grain protein content was measured in potassium application at flowering stage. In general, increasing the irrigation interval, and subsequent water stress, reduced plant growth and yield components. Application of potassium fertilizer at early growth stages increased yield and yield components, while in reproductive stages increased seed quality.

  12. An in vitro comparison of irrigation using photon-initiated photoacoustic streaming, ultrasonic, sonic and needle techniques in removing calcium hydroxide.

    Science.gov (United States)

    Arslan, H; Akcay, M; Capar, I D; Saygili, G; Gok, T; Ertas, H

    2015-03-01

    To evaluate the effect of various techniques including photon-initiated photoacoustic streaming (PIPS), ultrasonic, sonic and needle irrigation on the removal of calcium hydroxide [Ca(OH)2 ] from artificial grooves created in root canals. The root canals of 48 extracted single-rooted teeth with straight canals were prepared using ProTaper rotary instruments up to size 40. After the specimens had been split longitudinally, a standardized groove was prepared in the apical part of one segment that was filled with Ca(OH)2 powder mixed with distilled water. Each tooth was reassembled and the apices closed with wax. The specimens were irrigated for 60 s with one of the following techniques: needle irrigation using 17% EDTA, PIPS with 17% EDTA, ultrasonic irrigation using 17% EDTA and sonic irrigation (EndoActivator) using 17% EDTA. The root segments were then disassembled, and the amount of remaining Ca(OH)2 evaluated under a stereomicroscope at 25× magnification. A pixel count of Ca(OH)2 remaining on the artificially created grooves was recorded as a percentage of the overall groove surface. The data were evaluated statistically using one-way analysis of variance and the least significant difference post hoc tests at 95% confidence level (P = 0.05). Photon-initiated photoacoustic streaming was superior in removing Ca(OH)2 as compared to needle irrigation (P streaming provided complete removal of Ca(OH)2 from artificial grooves in straight root canals. Ultrasonic irrigation enhanced the Ca(OH)2 removal capacity of irrigating solution but did not provide complete removal from artificial grooves. © 2014 International Endodontic Journal. Published by John Wiley & Sons Ltd.

  13. Effectiveness of four different final irrigation activation techniques on smear layer removal in curved root canals : a scanning electron microscopy study.

    Directory of Open Access Journals (Sweden)

    Puneet Ahuja

    2014-02-01

    Full Text Available The aim of this study was to assess the efficacy of apical negative pressure (ANP, manual dynamic agitation (MDA, passive ultrasonic irrigation (PUI and needle irrigation (NI as final irrigation activation techniques for smear layer removal in curved root canals.Mesiobuccal root canals of 80 freshly extracted maxillary first molars with curvatures ranging between 25° and 35° were used. A glide path with #08-15 K files was established before cleaning and shaping with Mtwo rotary instruments (VDW, Munich, Germany up to size 35/0.04 taper. During instrumentation, 1 ml of 2.5% NaOCl was used at each change of file. Samples were divided into 4 equal groups (n=20 according to the final irrigation activation technique: group 1, apical negative pressure (ANP (EndoVac; group 2, manual dynamic agitation (MDA; group 3, passive ultrasonic irrigation (PUI; and group 4, needle irrigation (NI. Root canals were split longitudinally and subjected to scanning electron microscopy. The presence of smear layer at coronal, middle and apical levels was evaluated by superimposing 300-μm square grid over the obtained photomicrographs using a four-score scale with X1,000 magnification.Amongst all the groups tested, ANP showed the overall best smear layer removal efficacy (p < 0.05. Removal of smear layer was least effective with the NI technique.ANP (EndoVac system can be used as the final irrigation activation technique for effective smear layer removal in curved root canals.

  14. Health and taste related compounds in strawberries under various irrigation regimes and bio-stimulant application.

    Science.gov (United States)

    Kapur, Burcak; Sarıdaş, Mehmet Ali; Çeliktopuz, Eser; Kafkas, Ebru; Paydaş Kargı, Sevgi

    2018-10-15

    Strawberry has a unique status within the fruit species in terms of health and taste related compounds. This experimental study concerned the application of a bio-stimulant at various drip irrigation levels (IR125, IR100, IR75 and IR50). The effects of the bio-stimulant (seaweed extract) on the eating quality, i.e., the taste-related (TSS, fructose, glucose, sucrose and citric, malic, l-ascorbic acid), and health-related (antioxidant activity, total phenol, myricetin and quercetin) compounds were studied in two strawberry cultivars. The 'Rubygem' with its higher sugar and lower acid content has been more preferable than the 'Kabarla' cultivar. The bio-stimulant contributes to taste by improving the TSS, fructose, sucrose and also to health by increasing the quercetin content of the fruit which is associated to the cardiovascular properties and cancer reducing agents. The experiment conducted revealed significant increases only in the TSS contents and antioxidant activity under the IR50 and IR75 deficit irrigation treatments. Copyright © 2018 Elsevier Ltd. All rights reserved.

  15. Performance Evaluation Of Furrow Lengths And Field Application Techniques

    Directory of Open Access Journals (Sweden)

    Issaka

    2015-08-01

    Full Text Available Abstract The study evaluated performance of furrow lengths and field application techniques. The experiment was conducted on 2000 m2 field at Bontanga irrigation scheme. Randomized Complete Block Design RCBD was used with three replicates. The replicates include Blocks A B and C of furrow lengths 100 m 75 m and 50 m respectively. Each replicate had surge cut-off cut-back and bunds treatments. Water was introduced into the furrows and the advance distances and time were measured. Results of the study showed that at Block A surge technique recorded the highest advance rate of 1.26 minm and opportunity time of 11 min whilst bunds recorded the lowest advance rate of 0.92 minm. Significant difference 3.32 pamp88050.05 occurred between treatment means of field application techniques at Block A 100 m. Significant difference 2.71 pamp88050.05 was also recorded between treatment means. At Block B 75 m there was significant difference 2.71 pamp88050.05 between treatment means. No significant difference 0.14 pamp88040.05 was observed among surge cut-back and bunds techniques. There was significant difference 2.60 pamp88050.05 between treatment means but no significant difference between cut-back and bunds techniques in Block C 50 m. Their performance was ranked in the order Surge Cut-back Cut-off Bunds for furrow lengths 100 m 75 m and 50 m respectively.

  16. The collection of a minimum dataset and the application of DSSAT (Decision Support System for Agrotechnology Transfer) for optimizing wheat yield in irrigated cropping systems

    International Nuclear Information System (INIS)

    Heng, L.K.; Baethgen, W.E.; Moutonnet, P.

    2000-01-01

    A minimum dataset for testing of the CERES-Wheat model within DSSAT was collected during the course of an IAEA Co-ordinated Research Project on 'The use of nuclear techniques for optimizing fertilizer application under irrigated wheat to increase the efficient use of nitrogen fertilizers and consequently reduce environmental pollution'. A database entitled which contained the following information was subsequently created: soil characteristics, average yield, fertilizer N recovered by crop and residual effect, grain protein content, regional average yield, relative grain yield at various fertilizer N rates, assessment of nitrate pollution, economics of irrigated wheat, water use by source, water use efficiency, atypical precipitation events, type and uniformity of irrigation, and chlorophyll meter readings. This article presents some of these overall results from the database, as well as simulated results from the CERES-Wheat model. Good agreement between observed and simulated results was obtained for most growth parameters in most of the simulations. The ability to validate the model means that it can be used to refine specific management strategies with respect to fertilizer applications, yield and other parameters. (author)

  17. Applicability of statistical process control techniques

    NARCIS (Netherlands)

    Schippers, W.A.J.

    1998-01-01

    This paper concerns the application of Process Control Techniques (PCTs) for the improvement of the technical performance of discrete production processes. Successful applications of these techniques, such as Statistical Process Control Techniques (SPC), can be found in the literature. However, some

  18. Biogeosystem technique as a method to overcome the Biological and Environmental Hazards of modern Agricultural, Irrigational and Technological Activities

    Science.gov (United States)

    Kalinitchenko, Valery; Batukaev, Abdulmalik; Zinchenko, Vladimir; Zarmaev, Ali; Magomadov, Ali; Chernenko, Vladimir; Startsev, Viktor; Bakoev, Serojdin; Dikaev, Zaurbek

    2014-05-01

    Modern challenge for humanity is to replace the paradigm of nature use and overcome environmental hazards of agronomy, irrigation, industry, and other human activities in biosphere. It is utterly reasonable to stop dividing biosphere on shares - the human habitat and the environment. In the 21st century it is an outdated anthropocentrism. Contradicting himself to biosphere Humankind has the problems. The new paradigm of biosphere control by methods of Biogeosystem technique is on agenda of Humankind. Key directions of Biogeosystem technique. Tillage. Single rotary milling 20…30-50…60 sm soil layer optimizes the evolution and environment of soil, creates a favorable conditions for the rhizosphere, increases the biological productivity of biosphere by 30-50% compared to the standard agricultural practices for the period up to 40 years. Recycle material. Recycling of mineral and organic substances in soil layer of 20…30-50…60 sm in rotary milling soil processing provides wastes clean return to biosphere. Direct intrasoil substances synthesis. Environmentally friendly robot wasteless nanotechnology provides direct substances synthesis, including fertilizers, inside the soil. It eliminates the prerequisites of the wastes formation under standard industrial technologies. Selective substance's extraction from soil. Electrochemical robotic nanotechnology provides selective substances extraction from soil. The technology provides recovery, collection and subsequent safe industrial use of extracted substances out of landscape. Saving fresh water. An important task is to save fresh water in biosphere. Irrigation spends water 4-5 times more of biological requirements of plants, leads to degradation of soil and landscape. The intrasoil pulse continuous-discrete paradigm of irrigation is proposed. It provides the soil and landscape conservation, increases the biological productivity, save the fresh water up to 10-20 times. The subsurface soil rotary processing and

  19. A comprehensive guide for designing more efficient irrigation systems with respect to application control

    Science.gov (United States)

    Khaddam, Issam; Schuetze, Niels

    2017-04-01

    The worldwide water scarcity problems are expected to aggravate due to the increasing population and the need to produce more food. Irrigated agriculture is considered the highest consumer of fresh water resources with a rate exceeds 70% of global consumption. Consequently, an improvement in the efficiency of all irrigation methods, such as furrow or drip irrigation, becomes more necessary and urgent. Therefore, a more precise knowledge about soil water distribution in the root zone and the water balance components is required. For this purpose and as a part of the SAPHIR project (Saxonian Platform for high Performance Irrigation), a 2D simulation- based study was performed with virtual field conditions. The study investigates the most important design parameters of many irrigation systems, such as irrigation intensity and duration, and shows there influence on the water distribution efficiency. Furthermore, three main soil textures are used to test the impact of the soil hydraulic properties on irrigation effectiveness. A numerous number of irrigation scenarios of each irrigation system was simulated using HYDRUS 2D. Thereafter, the results were digitally calculated, compiled and made available online in the so called "Irrigation Atlases". The irrigation atlases provide graphical results of the soil moisture and pressure head distributions in the root zone. Moreover, they contain detailed information of the water balance for all simulated scenarios. The most studies evaluate the irrigation water demands on local, regional or global scales and for that an efficient water distribution is required. In this context, the irrigation atlases can serve as a valuable tool for the implementation of planned irrigation measures.

  20. [Endodontics in motion: new concepts, materials and techniques 3. The role of irrigants during root canal treatment].

    Science.gov (United States)

    van der Sluis, L W M

    2015-10-01

    The aims of root canal irrigation are the chemical dissolution or disruption and the mechanical detachment of pulp tissue, dentin debris and smear layer (instrumentation products), microorganisms (planktonic or biofilm) and their products from the root canal wall, their removal out of the root canal system and their chemical dissolution or disruption. Each of the endodontic irrigation systems has its own irrigant flow characteristics, which should fulfill these aims. Without flow (convection), the irrigant would have to be distributed through diffusion. This process is slow and depends on temperature and concentration gradients. On the other hand, convection is a faster and more efficient transport mechanism. During irrigant flow, frictional forces will occur, for example between the irrigant and the root canal wall (wall shear stress). These frictional forces have a mechanical cleaning effect on the root canal wall. These frictional forces are the result of the flow characteristics related to the different irrigation systems.

  1. Mapping air pollution. Application of nuclear techniques

    International Nuclear Information System (INIS)

    Parr, R.M.; Stone, S.F.; Zeisler, R.

    1996-01-01

    Nuclear techniques have important applications in the study of air pollution and many of its components. However, it is in the study of airborne particulate matter (APM) that nuclear analytical techniques find many of their most important applications. This article focuses on those applications, and on the work of the IAEA in this important field of study. 2 figs

  2. Development and Application of an Integrated Model for Representing Hydrologic Processes and Irrigation at Residential Scale in Semiarid and Mediterranean Regions

    Science.gov (United States)

    Herrera, J. B.; Gironas, J. A.; Bonilla, C. A.; Vera, S.; Reyes, F. R.

    2015-12-01

    Urbanization alters physical and biological processes that take place in natural environments. New impervious areas change the hydrological processes, reducing infiltration and evapotranspiration and increasing direct runoff volumes and flow discharges. To reduce these effects at local scale, sustainable urban drainage systems, low impact development and best management practices have been developed and implemented. These technologies, which typically consider some type of green infrastructure (GI), simulate natural processes of capture, retention and infiltration to control flow discharges from frequent events and preserve the hydrological cycle. Applying these techniques in semiarid regions requires accounting for aspects related to the maintenance of green areas, such as the irrigation needs and the selection of the vegetation. This study develops the Integrated Hydrological Model at Residential Scale, IHMORS, which is a continuous model that simulates the most relevant hydrological processes together with irrigation processes of green areas. In the model contributing areas and drainage control practices are modeled by combining and connecting differents subareas subjected to surface processes (i.e. interception, evapotranspiration, infiltration and surface runoff) and sub-surface processes (percolation, redistribution and subsurface runoff). The model simulates these processes and accounts for the dynamics of the water content in different soil layers. The different components of the model were first tested using laboratory and numerical experiments, and then an application to a case study was carried out. In this application we assess the long-term performance in terms of runoff control and irrigation needs of green gardens with different vegetation, under different climate and irrigation practices. The model identifies significant differences in the performance of the alternatives and provides a good insight for the maintenance needs of GI for runoff control.

  3. Industrial application of nuclear techniques in Australia

    International Nuclear Information System (INIS)

    Easey, J.F.

    1981-01-01

    The applications of nuclear techniques in Australia was reviewed - the work has been to aid: mining and mineral sector, the manufacturing, chemical and petroleum industries, hydrology and sedimentology

  4. Applicability of 87Sr/86Sr in examining return flow of irrigation water in highly agricultural watersheds in Japan

    Science.gov (United States)

    Yoshida, T.; Nakano, T.; Shin, K. C.; Tsuchihara, T.; Miyazu, S.; Kubota, T.

    2017-12-01

    Water flows in watersheds containing extensive areas of irrigated paddies are complex because of the substantial volumes involved and the repeated cycles of water diversion from, and return to, streams. For better management of low-flow conditions, numerous studies have attempted to quantify the return flow using the stable isotopes of water; however, the temporal variation in these isotopic compositions due to fractionation during evaporation from water surfaces hinders their application to watersheds with extensive irrigated paddies. In this study, we tested the applicability of the strontium isotopes (87Sr/86Sr, hereafter Sr ratio) for studying hydrological processes in a typical agricultural watershed located on the alluvial fan of the Kinu River, namely the Gogyo River, in central Japan. The Sr ratio of water changes only because of interactions with the porous media it flows through, or because of mixing with water that has different Sr ratios. We sampled water both at a single rice paddy, and on the watershed scale in the irrigated and non-irrigated periods. The soil water under the paddy decreased as sampling depth increased, and the soil water at a depth of 1.5 m showed a similar Sr ratio to the spring. The water sampled in the drainage channel with a concrete lined bottom showed a similar Sr ratio to the irrigation water, whereas that with a soil bottom was plotted between the plots of the irrigation water and shallow aquifer. These results suggest the Sr ratio decreases as it mixes with the soil water through percolation; whereas the Sr ratio will be less likely to change when water drains from paddies via surface pathways. The streamflow samples were plotted linearly on the Sr ratio and 1/Sr plot, indicating that the streamflow was composed of two end-members; the irrigation water and the shallow aquifer. The continuous decline in the Sr ratio along the stream suggests an exfiltration of water from the shallow aquifers. The stream water during the non-irrigated

  5. Industrial applications of nuclear techniques in Poland

    International Nuclear Information System (INIS)

    Michalik, J.St.

    1981-01-01

    Application of radioisotope techniques in a number of Polish industries was reviewed. Studies on the usage of radiotracer as an evaluation method for technological processes were carried out and the advantages of such application were discussed

  6. An assessment of colostomy irrigation.

    Science.gov (United States)

    Laucks, S S; Mazier, W P; Milsom, J W; Buffin, S E; Anderson, J M; Warwick, M K; Surrell, J A

    1988-04-01

    One hundred patients with permanent sigmoid colostomies were surveyed to determine their satisfaction and success with the "irrigation" technique of colostomy management. Most patients who irrigate their colostomies achieve continence. Odors and skin irritation are minimized. The irrigation method is economical, time efficient, and allows a reasonably liberal diet. It avoids bulky appliances and is safe. In appropriately selected patients, the irrigation technique is the method of choice for management of an end-sigmoid colostomy.

  7. The Application of Drip Irrigation System on Tomato (Lycopersicum Esculentum Mill)

    OpenAIRE

    Setyaningrum, Diah Ayu

    2014-01-01

    This study aimed to analyze the performance of drip irrigation systems, determine performance of tomato treated under the irrigation systems.Field research was conducted at the Laboratory of Land and Water Resources Engineering; and at the Laboratory ofintegrated field, Faculty of Agriculture, University of Lampung in August 2013 to December 2013.Irrigation systems consisted of main componens: water supplies, Polythilene lateral tube, and emitters. Emitter on every pot, were made of Polythile...

  8. Doses and application methods of Azospirillum brasilense in irrigated upland rice

    Directory of Open Access Journals (Sweden)

    Nayara F. S. Garcia

    Full Text Available ABSTRACT The study was carried out in Selvíria-MS, in the 2011/12 and 2012/13 agricultural years, aiming to evaluate the efficiency of Azospirillum brasilense in nitrogen fixation in upland rice, as a function of doses and application methods of the inoculant containing this diazotrophic bacterium. The experimental design was randomized blocks, arranged in a 4 x 4 factorial scheme, with 4 doses of inoculant (control without inoculation, 100, 200 and 300 mL of the commercial product ha-1 and 4 application methods (seed inoculation, application in the sowing furrow, soil spraying after sowing, and foliar spraying at the beginning of plant tillering, with 4 replicates. During the experiment, the agronomic characteristics, production components and yield of the rice crop were evaluated. It was concluded that the inoculant containing Azospirillum brasilense promotes increase (19% in the yield of upland rice under sprinkler irrigation when used at the dose of 200 mL ha-1, regardless of the application methods.

  9. Microbiological properties and oxidizable organic carbon fractions of an oxisol under coffee with split phosphorus applications and irrigation regimes

    Directory of Open Access Journals (Sweden)

    Adriana Rodolfo da Costa

    2013-02-01

    Full Text Available Phosphorus fertilization and irrigation increase coffee production, but little is known about the effect of these practices on soil organic matter and soil microbiota in the Cerrado. The objective of this study was to evaluate the microbiological and oxidizable organic carbon fractions of a dystrophic Red Latossol under coffee and split phosphorus (P applications and different irrigation regimes. The experiment was arranged in a randomized block design in a 3 x 2 factorial design with three split P applications (P1: 300 kg ha-1 P2O5, recommended for the crop year, of which two thirds were applied in September and the third part in December; P2: 600 kg ha-1 P2O5, applied at planting and then every two years, and P3: 1,800 kg ha-1 P2O5, the requirement for six years, applied at once at planting, two irrigation regimes (rainfed and year-round irrigation, with three replications. The layers 0-5 and 5-10 cm were sampled to determine microbial biomass carbon (MBC, basal respiration (BR, enzyme activity of acid phosphatase, the oxidizable organic carbon fractions (F1, F2, F3, and F4, and total organic carbon (TOC. The irrigation regimes increased the levels of MBC, microbial activity and acid phosphatase, TOC and oxidizable fractions of soil organic matter under coffee. In general, the form of dividing P had little influence on the soil microbial properties and OC. Only P3 under irrigation increased the levels of MBC and acid phosphatase activity.

  10. ELECTRICAL TECHNIQUES FOR ENGINEERING APPLICATIONS.

    Science.gov (United States)

    Bisdorf, Robert J.

    1985-01-01

    Surface electrical geophysical methods have been used in such engineering applications as locating and delineating shallow gravel deposits, depth to bedrock, faults, clay zones, and other geological phenomena. Other engineering applications include determining water quality, tracing ground water contaminant plumes and locating dam seepages. Various methods and electrode arrays are employed to solve particular geological problems. The sensitivity of a particular method or electrode array depends upon the physics on which the method is based, the array geometry, the electrical contrast between the target and host materials, and the depth to the target. Each of the available electrical methods has its own particular advantages and applications which the paper discusses.

  11. Economic analysis of different mulch applications and irrigation programs in apple production

    Directory of Open Access Journals (Sweden)

    Dilek Karamürsel

    2017-12-01

    Full Text Available Economic analysis of different mulch materials and irrigation programs on Fuji apple variety grafted onto M9 rootstock was made in this study. Mulch treatments consisted of four different mulch materials including black textile, wheat straw, rose oil processing wastes and no mulch. There were three different irrigation programs for each mulch treatment. Irrigation programs also consisted of three different programs including starting irrigation when available water holding capacity of 20%, 40% and 60% at the effective root zone. Total production costs had fluctuating according to treatments. While rose oil processing and the program starting irrigation when available water holding capacity of 60% at the root zone was used had the lowest total production costs, wheat straw and the program starting irrigation when available water holding capacity of 20% at the root zone was used had the highest values. But, black textile mulch and the program which starting at irrigation when available water holding capacity of 20% at the root zone was used had the lowest unit production cost with 0.39 TL kg-1 highest yield, extra and class I fruits. Furthermore, according to apple marketing prices of 2014, considering yield and fruit quality, the highest gross profit with 51 223 TL ha-1 was obtained from black textile mulch and the program starting irrigation when available water holding capacity of 20% at the root zone was used.

  12. Effects of application timing of saline irrigation water on broccoli production and quality

    Science.gov (United States)

    Irrigation with moderately saline water is a necessity in many semi-arid areas of the Mediterranean Basin, and requires adequate irrigation management strategies. Broccoli (Brassica oleracea var. italica), a crop moderately tolerant to salinity stress, was used to evaluate the effects of the applica...

  13. Proper Management Of Irrigation Water And Nitrogen Fertilizer To Improve Spinach Yield And Reserve Environment Using 15N Tracer Technique

    International Nuclear Information System (INIS)

    GADALLA, A.M.; GALAL, Y.G.M.; ISMAIL, M.M.; EL DEGWY, S.A.; HAMDY, A.; HAMED, L.M.

    2010-01-01

    The effect of water regime and N-fertilizer application rate and modality of its application were studied by the aim of identifying the most proper and effective combination of the above studied variables that provide a satisfactory spinach yield as well as to minimize the rational use of chemical nitrogen fertilizers to save the surrounding environment and to achieve a good water saving. The results indicated that reasonable production of spinach crop could be achieved by using 75% of the recommended rate of nitrogen fertilizer combined with 80% of the required water. It means that 20% of the required water could be saved as well as 25% of the required quantity of N-fertilizer. Similarly, the splitting of N-fertilizer into two equal doses prevented the excess of nitrate to be moved to the underground water lowering its concentration in the blades and plant leaves. Drip irrigation system accompanied with proper water scheduling regime and good fertilizer application practices is considered as a useful management practice that could be applied to improve the sandy soil productivity.

  14. Applications of the phased array technique

    International Nuclear Information System (INIS)

    Erhard, A.; Schenk, G.; Hauser, Th.; Voelz, U.

    1999-01-01

    The application of the phased array technique was limited to heavy and thick wall components as present in the nuclear industry. With the improvement of the equipment and probes other application areas are now open for the phased array technique, e.g. the inspection of the turbine blade root, weld inspection in a wall thickness range between 12 and 40 mm, inspection of aircraft components, inspection of spot welds or inspection of concretes. The aim of the use of phased array techniques has not been changed related to the first applications, i.e. the adaptation of the sound beam to the geometry by steering the angel of incidence or the skewing angle as well as the focussing of sound fields. Due to the fact, that the new applications of the phased array techniques in some cases don't leave the laboratories for the time being, the examples of this contribution will focus applications with practical background. (orig.)

  15. New applications using phased array techniques

    International Nuclear Information System (INIS)

    Erhard, A.; Schenk, G.; Hauser, Th.; Voelz, U.

    2001-01-01

    In general, the application of phased array techniques used to be limited to heavy components with large wall thicknesses, such as those in the nuclear power industry. With the improvement of the phased array equipment, including phased array search units, other application areas are now accessible for the phased array inspection technique, e.g. the inspection of turbine blade roots, weld inspection with a wall thickness ranging from 12 to 40 mm, inspection of aircraft components, inspection of spot welds and the inspection of concrete building components. The objective for the use of phased array techniques has not significantly changed since their first application, e.g. instant adjustment of the sound beam to the geometry of the test object by steering incidence angle, skew angle and/or sound field focusing. Because some new phased array technique applications are still in the experimental (laboratory) stage, this article will focus on some examples for practical, real-weld applications

  16. Micro manufacturing techniques and applications

    CERN Document Server

    Du, Ruxu; Li, Zifu

    2013-01-01

    Micro/meso-scale manufacturing has been developed in research fields of machining, forming, materials and others, but its potential to industries are yet to be fully realized. The theme of the current volume was to build a bridge joining academic research and industrial needs in micro manufacturing. Among the 12 papers selected for publication are three keynote addresses onmicro and desktop factories for micro/meso-scale manufacturing applicationsand future visions, tissue cutting mechanics and applications for needlecore biopsy and guidance, and micro-texturing onto amorphous carbonmaterials

  17. Diurnal Activity of Drosophila suzukii (Diptera: Drosophilidae) in Highbush Blueberry and Behavioral Response to Irrigation and Application of Insecticides.

    Science.gov (United States)

    Van Timmeren, Steven; Horejsi, Logan; Larson, Shadi; Spink, Katherine; Fanning, Philip; Isaacs, Rufus

    2017-10-01

    Spotted wing Drosophila, Drosophila suzukii Matsumura (Diptera: Drosophilidae), is an invasive vinegar fly that has become a primary direct pest of berry crops worldwide. We conducted 2 yr of behavioral studies in blueberry plantings to determine how fly activity varied throughout the day. Observations of diurnal activity of adult D. suzukii found the greatest activity in the morning hours between 0600 and 0800 hours, when the majority of flies were on the berries. Flies were also active in the evening mainly between 1800 and 2000 hours; however, this trend was more prominent in 2015, which had cooler and more humid evenings. Experiments examining the effect of irrigation on D. suzukii behavior showed that flies remained active during and after irrigation. The effect of insecticide treatments alone and in combination with irrigation revealed that treatment with spinosad had limited effects on the number of flies per bush, whereas spinetoram reduced the number flying and on the bushes in some cases. Zeta-cypermethrin caused longer and more consistent reduction in D. suzukii flying and on bushes. In all treatments, we observed surviving flies flying near and on treated bushes, indicating that these insecticides do not completely deter fly activity. Irrigation did not influence the effects of zeta-cypermethrin on fly behavior during daily observations up to 3 d after application. Our results highlight that the diurnal patterns of activity of D. suzukii on host plants are flexible and are relatively unaffected by irrigation or insecticide applications. © The Author 2017. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  18. Performability Modelling Tools, Evaluation Techniques and Applications

    NARCIS (Netherlands)

    Haverkort, Boudewijn R.H.M.

    1990-01-01

    This thesis deals with three aspects of quantitative evaluation of fault-tolerant and distributed computer and communication systems: performability evaluation techniques, performability modelling tools, and performability modelling applications. Performability modelling is a relatively new

  19. Biological degradation of chernozems under irrigation

    Directory of Open Access Journals (Sweden)

    Oksana Naydyonova

    2014-12-01

    reduction the number of microorganisms and the diversity of fungi species, repression of cellulose destroying capacity, decrease invertase activity and the rate of humification, intensifying mineralization processes and soil toxicity increasing. Long-term irrigation of ordinary chernozem (Kharkiv Region with fresh water in moderate regime under 7-field crop rotation including alfalfa caused no disturbances of microbial cenosis. In this case parameters of biological indices did not deviate from the level of its non-irrigated analogue. Irrigation with saline water causes more profound negative changes of microbial cenosis of chernozem, which not always can be corrected using agroameliorative techniques. Intensive irrigation with saline water with total mineralization from 1.2 to 2.2 g/l of ordinary chernozem (Odesa Region for 13 years has led to a significant degradation changes in the structure and functioning of its microbial cenosis, its radical alteration such as oppression of microflora, decrease in the number of its main groups by 30 – 40 %, intensification of its mineralization function. Application of agroameliorative techniques (such as annually use of phosphogypsum 3 t/ha or /and complex measures (phosphogypsum 3 t/ha annually + N150P90K60 + manure 18 t/ha of crop rotation enable to regulate of soil biodynamic processes and partially or completely eliminate the phenomena of biological degradation. It was stated that after the cessation of irrigation the degradation changes of ordinary chernozem’s biological properties caused by irrigation with saline water were gradually restored.

  20. TV content analysis techniques and applications

    CERN Document Server

    Kompatsiaris, Yiannis

    2012-01-01

    The rapid advancement of digital multimedia technologies has not only revolutionized the production and distribution of audiovisual content, but also created the need to efficiently analyze TV programs to enable applications for content managers and consumers. Leaving no stone unturned, TV Content Analysis: Techniques and Applications provides a detailed exploration of TV program analysis techniques. Leading researchers and academics from around the world supply scientifically sound treatment of recent developments across the related subject areas--including systems, architectures, algorithms,

  1. Pendimethalin and oxyfluorfen degradation under two irrigation conditions over four years application.

    Science.gov (United States)

    Alister, Claudio A; Gomez, Patricio A; Rojas, Sandra; Kogan, Marcelo

    2009-05-01

    A four-year field study was conducted to determine the effect of pluviometric conditions on pendimethalin and oxyfluorfen soil dynamics. Adsorption, dissipation and soil movement were studied in a sandy loam soil from 2003 to 2007. Pendimethalin and oxyfluorfen were applied every year on August at 1.33 and 0.75 kg ha(-1), respectively. Herbicide soil concentrations were determined at 0, 10, 20, 40, 90 and 340 days after application (DAA), under two pluviometric regimens, natural rainfall and irrigated (30 mm every 15 days during the first 90 DAA). More than 74% of the herbicide applied was detected at the top 2.5 cm layer for both herbicides, and none was detected at 10 cm or deeper. Pendimethalin soil half-life ranged from 10.5 to 31.5 days, and was affected mainly by the time interval between application and the first rain event. Pendimethalin soil residues at 90 DAA fluctuated from 2.5 to 13.8% of the initial amount applied, and it decreased to 2.4 and 8.6% at 340 DAA. Oxyfluorfen was more persistent than pendimethalin as indicated by its soil half-life which ranged from 34.3 to 52.3 days, affected primarily by the rain amount at the first rainfall after application. Oxyfluorfen soil residues at 90 DAA ranged from 16.7 to 34.8% and it decreased to 3.3 and 17.9% at 340 DAA. Based on half-life values, herbicide soil residues after one year, and soil depth reached by the herbicides, we conclude that both herbicides should be considered as low risk to contaminate groundwater. However, herbicide concentration at the top 2.5 cm layer should be considered in cases where runoff or soil erosion could occur, because of the potential for surface water contamination.

  2. Pesticide Application among Farmers in the Catchment of Ashaiman Irrigation Scheme of Ghana: Health Implications

    Directory of Open Access Journals (Sweden)

    Memuna M. Mattah

    2015-01-01

    Full Text Available Pesticide use in modern day agriculture has increased tremendously. Pesticides are used to control pests and weeds, as well as protect crops from postharvest losses; however, their effects on humans and the environment cannot be overstated. This study examined pesticide acquisition, handling, and use among 120 farmers within the catchment of a small urban irrigation scheme. Also, in-depth interviews and focus group discussions were conducted among selected farmers through which further data was collected to augment that of the survey. Twelve types of pesticides, including herbicides, insecticides, and fungicides, were found in use in the study areas. Three main sources of information about pesticides were identified, 43.3% from extension officers, 39.2% from agrochemical dealers, and 10% from colleague farmers. Seventy-five percent (75% of the respondents purchased the pesticides from agrochemical shops. Out of 74 farmers who were observed spraying pesticides on their farms, only 25.7% wore dresses that covered their whole body but without goggles. About sixty-seven percent (66.7% of the farmers whose chemical got finished left the containers on their farms or threw them into the bushes around. The frequency of application was influenced by affordability and size of farm, among others. The study recommended that training of farmers on pesticide handling and use should be intensified.

  3. [Phosphorus application effects and input threshold of Chinese cabbage in the oasis irrigation region.

    Science.gov (United States)

    Lian, Cai Yun; Ma, Zhong Ming

    2018-02-01

    To resolve the problem of higher application and lower use efficiency of phosphorus fertilizer of Chinese cabbage (Brassica pekinensis), the yield, use efficiency of phosphate fertilizer and soil phosphate balance were examined by a located field trial in Zhangye Observation and Experiment Station of the Agro-ecological Environment in oasis irrigation region from 2011 to 2013. The results showed that the yield increased with the increase of phosphorus fertilization rate from 0 to 112.52 kg P·hm -2 , beyond which there would be no further enhancement. The yield was 5489.1 kg·hm -2 at 112.52 kg P·hm -2 treatment. This treatment increased the yield by 13.3%-23.8%, under which the phosphorus use efficiency was 14.2%. Soil Olsen-P and CaCl 2 -P were positively correlated. For 111.1 kg P·hm -2 treatment, the content of soil Olsen-P was 24.22 mg·kg -1 , with no phosphorus leaching and no pollution. At the rate of 60.17 kg P·hm -2 , there was a balance between phosphorus input and output and the phosphate demand of Chinese cabbage being met. In conclusion, the optimal phosphorus threshold was 60.17-112.52 kg·hm -2 for Chinese cabbage, the amount at which could reduce the risk of phosphorus pollution.

  4. SWAT application in intensive irrigation systems: Model modification, calibration and validation

    OpenAIRE

    Dechmi, Farida; Burguete, Javier; Skhiri, Ahmed

    2012-01-01

    The Soil and Water Assessment Tool (SWAT) is a well established, distributed, eco-hydrologic model. However, using the study case of an agricultural intensive irrigated watershed, it was shown that all the model versions are not able to appropriately reproduce the total streamflow in such system when the irrigation source is outside the watershed. The objective of this study was to modify the SWAT2005 version for correctly simulating the main hydrological processes. Crop yield, total streamfl...

  5. Role of transpiration reduction during center-pivot sprinkler irrigation in application efficiency

    OpenAIRE

    Urrego Pereira, Yenny Fernanda; Cavero Campo, José; Medina Pueyo, Eva Teresa; Martínez-Cob, Antonio

    2013-01-01

    The magnitude and duration of corn transpiration reduction during center-pivot sprinkler irrigation was analyzed on a commercial plot. The irrigation event was defined as the period during which the pivot arm was passing over the transect AC and water droplets were moistening the plants (moist treatment). Corn transpiration rates were measured at three spots of that transect and simultaneously at another spot (dry treatment) located approximately 270 m east from the transect AC. Corn transpir...

  6. Economics on nuclear techniques application in industry

    International Nuclear Information System (INIS)

    Kato, Masao

    1979-01-01

    The economics of the application of nuclear techniques to industry is discussed. Nuclear techniques were applied to gauging (physical measurement), analysis, a radioactive tracer method, electrolytic dissociation, and radiography and were found to be very economical. They can be applied to manufacturing, mining, oceano-engineering, environmental engineering, and construction, all of which have a great influence on economics. However, because the application of a radioactive tracer technique does not have a direct influence on economics, it is difficult to estimate how beneficial it is. The cost-benefit ratio method recommended by IAEA was used for economical calculations. Examples of calculations made in gauging and analysis are given. (Ueda, J.)

  7. Response of Soil Mesofauna to Long-Term Application of Feedlot Manure on Irrigated Cropland.

    Science.gov (United States)

    Miller, Jim J; Battigelli, Jeff P; Beasley, Bruce W; Drury, Craig F

    2017-01-01

    Long-term application of feedlot manure to cropland may influence soil mesofauna. These organisms affect the health, structure, and fertility of soils, organic matter decomposition, and crop growth. The objective was to study the long-term (16-17 yr) influence of feedlot manure type and bedding on soil mesofauna over 2 yr (2014-2015). Stockpiled or composted feedlot manure with straw (ST) or wood-chip (WD) bedding (plus unamended control) was annually applied (13 Mg ha dry wt.) to an irrigated clay loam soil with continuous barley (). Intact cores were taken from surface (0-5 cm) soil in the fall, and the densities of Acari (mites) suborders and Collembola (springtails) families were determined. Manure type had no significant ( > 0.05) effect on soil mesofauna density. In contrast, there was a significant two- to sixfold increase in density with WD- compared with ST-amended soils of total Acari in 2014 and 2015, as well as total Collembola, total Acari and Collembola, oribatid mites, and entomobryid springtails in 2014. The bedding effect was attributed to significantly greater soil water content and lower bulk density for WD than ST. Density of soil mesofauna was not significantly greater in amended soils than in unamended soils. A shift by feedlot producers from stockpiled to composted feedlot manure application should have no effect on soil mesofauna density, whereas a shift from ST to WD bedding may increase the density of certain soil mesofauna, which may have a beneficial effect on soil. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

  8. Proposed applications with implementation techniques of the upcoming renewable energy resource, The Tesla Turbine

    International Nuclear Information System (INIS)

    Khan, M Usman Saeed; Maqsood, M Irfan; Ali, Ehsan; Jamal, Shah; Javed, M

    2013-01-01

    Recent research has shown that tesla turbine can be one of the future efficient sources of renewable energy. Modern techniques used for designing of tesla turbine have given optimum results regarding efficiency and applications. In this paper we have suggested fully coordinated applications of tesla turbine in different fields particularly in power generation at both low level and high level generation. In Energy deficient countries the tesla turbine has wide range of applications and it can play an important role in energy management system. Our proposed applications includes, - the use of tesla turbine as renewable energy resource; - using tesla turbine in distributed generation system; - use of tesla turbine at home for power generation; - use of tesla turbine in irrigation channels; - using tesla turbine in hybrid electric vehicles; All applications are explained with the help of flow charts and block diagrams and their implementation techniques are also explained in details. The results of physical experiments and simulations are also included for some applications.

  9. Analysis of water application techniques for growing tomatoes in small pots on different substrates. Note 2

    Directory of Open Access Journals (Sweden)

    Luigi Cavazza

    Full Text Available The response of the tomato plants to the irrigation regimes compared in the previous study, particularly when compared with the response to the peat fraction in the mixture, was modest, often irregular and subject to complex interactions with the former factor. This result could depend partially on the fact that the parameters for the water regime applied during the trials were chosen to prevent exposing the plants to excessive stress through lack of water or excess water. This note analyses the technique used to apply the water. Two main water application parameters were identified parameter a expressing the mean moisture level of the pot during growing, and parameter b expressing the amplitude of the variation in moisture level between the irrigation threshold and the level to which the water was topped up at each watering. The actual mean volume of irrigation during the cultivation period was compared with the theoretically predicted value and the discrepancy explained. The role of parameter a and b are proposed to define the irrigation regime applied and the water regime as such can be defined by these two parameters a and b, as a general composite index. Furthermore the effect on the biological performance of both parameters a and b were studied obtaining a clearer picture of the effect of the water regime. The role of both parameters, a and b were synthesized in a specific composite index for each individual characteristic of the plant after taking in account the principal causes of their variations.

  10. Optical rangefinding applications using communications modulation technique

    Science.gov (United States)

    Caplan, William D.; Morcom, Christopher John

    2010-10-01

    A novel range detection technique combines optical pulse modulation patterns with signal cross-correlation to produce an accurate range estimate from low power signals. The cross-correlation peak is analyzed by a post-processing algorithm such that the phase delay is proportional to the range to target. This technique produces a stable range estimate from noisy signals. The advantage is higher accuracy obtained with relatively low optical power transmitted. The technique is useful for low cost, low power and low mass sensors suitable for tactical use. The signal coding technique allows applications including IFF and battlefield identification systems.

  11. Constitution of Solar Irrigation Pump Station and Its Application%太阳能提灌站的构成及其应用

    Institute of Scientific and Technical Information of China (English)

    阮红丽; 李光辉; 蒋辉霞; 曾文明; 周小波; 刘波; 廖功磊

    2012-01-01

    介绍了太阳能提灌站的构成,并对其应用实例进行分析,以期为太阳能提灌站的应用提供参考。%Constitution'of solar irrigation pump station was introduced, and its application example was analyzed, so as to provide references for application of solar irrigation pump station.

  12. Evaluation of Tomato Yield and Quality under Deficit Irrigation conditions and Simultaneous Application of Superabsorbent Polymer, Shading and Mulches

    Directory of Open Access Journals (Sweden)

    Maryam Bostani

    2017-12-01

    % probability level. Results and Discussion Analysis of variances revealed that effects of irrigation intervals, treatments and their interactions were highly significant on total yield, potential yield, marketable yield, blossom end rotten fruits yield, sunburned fruits yield, cracked fruits yield, average weight of fruits and number of main and lateral branches. Also, effects of treatments on number of days to 50 percent flowering, plant height and fruit wall thickness and effects of irrigation intervals on fruit shape index were significant at 5 percent of probability level. Results showed that increasing irrigation intervals decreased yield and its important components and increased blossom end rot, and cracked fruits. Increasing irrigation intervals from 3 to 9 days decreased 50 percent of total and marketable yield and quadrupled percentage of blossom end rotten fruits. Although shading improved total and marketable yield, but recording the highest number of days to 50 percent flowering for plants grown under shade of Saran® clothes, proved that shading delays harvesting of tomato. The maximum of total and potential yields produced by superabsorbent + shading + mulch treatment and the highest percentage of marketable fruits recorded for superabsorbent, mulches and shading + mulch, respectively. Application of shading clothes alone or along with mulches or superabsorbent minimized the percentage of sunburned fruits. The biggest fruits produced by treatments in which mulches were participated. Increasing irrigation intervals to six and nine days extremely decreased percentage of marketable and blossom rotten fruits, while increased cracked fruits. Conclusion Generally, for short irrigation intervals, superabsorbent + shading + mulch compound treatment and for extreme water deficit conditions and irrigation intervals more than six days adding superabsorbent A200 (10 g.plant-1, mixing into 30 cm depth of soil is recommended to improve yield and quality of tomato crop.

  13. Effect of Irrigation with Wastewater and Foliar Application of Complete Fertilizer on Forage Yield and Yield Components of Foxtail Millet (Setaria italica

    Directory of Open Access Journals (Sweden)

    A Ahmadi Aghtape

    2013-08-01

    Full Text Available In order to study effect of irrigation with wastewater and foliar application of complete fertilizer on forage yield and seed yield and yield components of foxtail millet (Setaria italica. A split plot experiment based on randomized complete block design with three replications was conducted at the Agriculture Institute of Zabol University in year 2009. Treatments included three levels of irrigation: Irrigation with well water at all stages of grows (control, Irrigation with wastewater and tap water alternately, Irrigation with wastewater for all growing stages, as the main plot and sprayed with three levels of complete fertilizer (NATBA-LIB: Non spraying (control, sprayed with 600 and 1200 gram of complete fertilizer in each hectare, as were the subplots. Results showed that irrigation with wastewater and complete fertilizer sprayed had significant effect on all traits except leaf to stem ratio. Furthermore, among the irrigation treatments, irrigation with wastewater in total growing period, and wastewater and tap water alternately lead to significant increase in grain yield, forage yield and yield components. Among the sprayed treatments, sprayed with 1200 gram of complete fertilizer had highest forage yield and grain.

  14. SWAT application in intensive irrigation systems: Model modification, calibration and validation

    Science.gov (United States)

    Dechmi, Farida; Burguete, Javier; Skhiri, Ahmed

    2012-11-01

    SummaryThe Soil and Water Assessment Tool (SWAT) is a well established, distributed, eco-hydrologic model. However, using the study case of an agricultural intensive irrigated watershed, it was shown that all the model versions are not able to appropriately reproduce the total streamflow in such system when the irrigation source is outside the watershed. The objective of this study was to modify the SWAT2005 version for correctly simulating the main hydrological processes. Crop yield, total streamflow, total suspended sediment (TSS) losses and phosphorus load calibration and validation were performed using field survey information and water quantity and quality data recorded during 2008 and 2009 years in Del Reguero irrigated watershed in Spain. The goodness of the calibration and validation results was assessed using five statistical measures, including the Nash-Sutcliffe efficiency (NSE). Results indicated that the average annual crop yield and actual evapotranspiration estimations were quite satisfactory. On a monthly basis, the values of NSE were 0.90 (calibration) and 0.80 (validation) indicating that the modified model could reproduce accurately the observed streamflow. The TSS losses were also satisfactorily estimated (NSE = 0.72 and 0.52 for the calibration and validation steps). The monthly temporal patterns and all the statistical parameters indicated that the modified SWAT-IRRIG model adequately predicted the total phosphorus (TP) loading. Therefore, the model could be used to assess the impacts of different best management practices on nonpoint phosphorus losses in irrigated systems.

  15. Nitrogen utilization efficiencies and yield responses of drip-irrigated tomatoes and peppers as influenced by soil application and fertigation

    International Nuclear Information System (INIS)

    Elinc, F.; Deviren, A.; Oeztuerk, A.

    1996-01-01

    These greenhouse studies conducted on a Mediterranean Terra Rose soil in an plastic greenhouse, were designed to investigate the response of drip-irrigated tomatoes (Lycopersicon esculentum Mill.)grown as a spring production and peppers (Capsicum annuum) heated for anti frost to four nitrogen levels continually applied with the irrigation stream. Water containing 0,50,100 or 150 mgN/l for tomatoes, 0,70,140 or 210 mgN/l for peppers as NH 4 S 2 O 4 , and uniformly supplied with 60 and 180 mg/l of P and K respectively were applied two times a week. Three adjacent plants in each plot were fertigated with N labeled NH 4 S 2 O 4 (2% a.e. enrichment). These treatments were compared with banded application of NH 4 S 2 O 4 at the rate of 320 kgN/ha for tomatoe sand 350 kgN/ha for peppers that were equivalent to the 100 mgN/l and 140 mgN/l treatments. The total amount of water applied was 345 mm for tomatoes and 260 mm for peppers. The results obtained showed that the highest yield was achieved in 100 mgN/l for tomatoes and in 140 mgN/l for peppers. The percentage fertilizer N utilization and yield increase by tomatoes and peppers were significantly increased with applying the N fertilizer by the irrigation water, fertigation, relative to the soil application of N at the same level fertilization. Evidently, the nutrient uptake efficiency as indicated by the highest yield is higher with fertigation which is extend means more environmental friendly approach. These experiments demonstrated that the amount of N fertilizer by applying in the irrigation water is to be recommended 100 mgN/l for tomatoes and 140 mgN/l for peppers to obtain high yield

  16. The application of parallel wells to support the use of groundwater for sustainable irrigation

    Science.gov (United States)

    Suhardi

    2018-05-01

    The use of groundwater as a source of irrigation is one alternative in meeting water needs of plants. Using groundwater for irrigation requires a high cost because of the discharge that can be taken is limited. In addition, the use of large groundwater can cause environmental damage and social conflict. To minimize costs, maintain quality of the environment and to prevent social conflicts, it is necessary to innovate in the groundwater taking system. The study was conducted with an innovation of using parallel wells. Performance is measured by comparing parallel wells with a single well. The results showed that the use of parallel wells to meet the water needs of rice plants and increase the pump discharge up to 100%. In addition, parallel wells can reduce the influence radius of taking of groundwater compared to single well so as to prevent social conflict. Thus, the use of parallel wells can support the achievement of the use of groundwater for sustainable irrigation.

  17. Phase equilibria basic principles, applications, experimental techniques

    CERN Document Server

    Reisman, Arnold

    2013-01-01

    Phase Equilibria: Basic Principles, Applications, Experimental Techniques presents an analytical treatment in the study of the theories and principles of phase equilibria. The book is organized to afford a deep and thorough understanding of such subjects as the method of species model systems; condensed phase-vapor phase equilibria and vapor transport reactions; zone refining techniques; and nonstoichiometry. Physicists, physical chemists, engineers, and materials scientists will find the book a good reference material.

  18. Evaluation model development for sprinkler irrigation uniformity ...

    African Journals Online (AJOL)

    use

    Sprinkle and trickle irrigation. The. Blackburn Press, New Jersey, USA. Li JS, Rao MJ (1999). Evaluation method of sprinkler irrigation nonuniformity. Trans. CSAE. 15(4): 78-82. Lin Z, Merkley GP (2011). Relationships between common irrigation application uniformity indicators. Irrig Sci. Online First™, 27 January. 2011.

  19. Industrial applications of radioisotope techniques in Poland

    International Nuclear Information System (INIS)

    Michalik, J.St.

    1985-01-01

    A general review of applications of radioisotope techniques in the Polish industry for about 25 years is given. The radiotracer methods used in metallurgy, hydrometallurgy, glass industry, oil and petroleum industries, in material testing and in other industries are described. Neutron activation analysis methods as well as nuclear gauges for industry (thickness meters, density meters, conveyer belt weigher, acid concentration meters and others) are also presented. The economic advantages of industrial applications of radioisotope techniques are described too. 42 refs., 43 figs., 11 tabs. (author)

  20. Techniques and applications of path integration

    CERN Document Server

    Schulman, L S

    2005-01-01

    A book of techniques and applications, this text defines the path integral and illustrates its uses by example. It is suitable for advanced undergraduates and graduate students in physics; its sole prerequisite is a first course in quantum mechanics. For applications requiring specialized knowledge, the author supplies background material.The first part of the book develops the techniques of path integration. Topics include probability amplitudes for paths and the correspondence limit for the path integral; vector potentials; the Ito integral and gauge transformations; free particle and quadra

  1. Immobilization Techniques for Microarray: Challenges and Applications

    Directory of Open Access Journals (Sweden)

    Satish Balasaheb Nimse

    2014-11-01

    Full Text Available The highly programmable positioning of molecules (biomolecules, nanoparticles, nanobeads, nanocomposites materials on surfaces has potential applications in the fields of biosensors, biomolecular electronics, and nanodevices. However, the conventional techniques including self-assembled monolayers fail to position the molecules on the nanometer scale to produce highly organized monolayers on the surface. The present article elaborates different techniques for the immobilization of the biomolecules on the surface to produce microarrays and their diagnostic applications. The advantages and the drawbacks of various methods are compared. This article also sheds light on the applications of the different technologies for the detection and discrimination of viral/bacterial genotypes and the detection of the biomarkers. A brief survey with 115 references covering the last 10 years on the biological applications of microarrays in various fields is also provided.

  2. Digital Holographic Microscopy Principles, Techniques, and Applications

    CERN Document Server

    Kim, Myung K

    2011-01-01

    Digital holography is an emerging field of new paradigm in general imaging applications. By replacing the photochemical procedures with electronic imaging and having a direct numerical access to the complex optical field, a wide range of new imaging capabilities become available, many of them difficult or infeasible in conventional holography. An increasing number of researchers—not only in optical physics and optical engineering, but also in diverse applications areas such as microbiology, medicine, marine science, particle analysis, microelectromechanics, and metrology—are realizing and exploiting the new capabilities of digital holography. Digital Holographic Microscopy: Principles, Techniques, and Applications, by Dr. Myung K. Kim, is intended to provide a brief but consistent introduction to the principles of digital holography as well as to give an organized overview of the large number of techniques and applications being developed. This will also shed some light on the range of possibilities for f...

  3. Root distribution pattern of triticale varieties under irrigated and unirrigated conditions using 32P plant injection technique

    International Nuclear Information System (INIS)

    Mahajan, J.P.; Soni, B.K.; Bhargava, B.S.

    1977-01-01

    A study on the root distribution pattern of four triticale varieties (6TA-204-3, 6TA-204-4, S-520 and S-411) under irrigated and unirrigated conditions showed that in general, there was a more profused root system in irrigated conditions than in the unirrigated ones. The lateral root distribution was adversely affected under unirrigated conditions. Root density of different varieties, in a soil segment of 15 cm diameter and 48 cm depth grown under unirrigated conditions, was in the following order : S-520 > 6 TA-204-3 > 6 TA-204-4 > S-411 while under irrigated conditions the order was : 6 TA-204-3 > S-520 > 6 TA-204-4 > S-411. (author)

  4. Irrigation water policy analysis using a business simulation game

    Science.gov (United States)

    Buchholz, M.; Holst, G.; Musshoff, O.

    2016-10-01

    Despite numerous studies on farmers' responses to changing irrigation water policies, uncertainties remain about the potential of water pricing schemes and water quotas to reduce irrigation. Thus far, policy impact analysis is predominantly based upon rational choice models that assume behavioral assumptions, such as a perfectly rational profit-maximizing decision maker. Also, econometric techniques are applied which could lack internal validity due to uncontrolled field data. Furthermore, such techniques are not capable of identifying ill-designed policies prior to their implementation. With this in mind, we apply a business simulation game for ex ante policy impact analysis of irrigation water policies at the farm level. Our approach has the potential to reveal the policy-induced behavioral change of the participants in a controlled environment. To do so, we investigate how real farmers from Germany, in an economic experiment, respond to a water pricing scheme and a water quota intending to reduce irrigation. In the business simulation game, the participants manage a "virtual" cash-crop farm for which they make crop allocation and irrigation decisions during several production periods, while facing uncertain product prices and weather conditions. The results reveal that a water quota is able to reduce mean irrigation applications, while a water pricing scheme does not have an impact, even though both policies exhibit equal income effects for the farmers. However, both policies appear to increase the variation of irrigation applications. Compared to a perfectly rational profit-maximizing decision maker, the participants apply less irrigation on average, both when irrigation is not restricted and when a water pricing scheme applies. Moreover, the participants' risk attitude affects the irrigation decisions.

  5. The project for the study of Wurno irrigation scheme area in the Rima hydrological basin, Sokoto State, Nigeria for Fadama irrigation and water supply, using isotope techniques

    International Nuclear Information System (INIS)

    Maduabuchi, C.

    2000-07-01

    This publication summarizes the result of the project on the use of isotope techniques for the study of recharge and discharge of the Sokoto-Rima hydrological basin in the semi-arid and northwestern part of Nigeria

  6. Effect of irrigation water salinity and zinc application on yield, yield components and zinc accumulation of wheat

    Directory of Open Access Journals (Sweden)

    mohamad ahmadi

    2009-06-01

    Full Text Available Salinity stress is one of the most important problems of agriculture in crop production in arid and semi arid regions. Under these conditions, in addition to management strategies, proper and adequate nutrition also has an important role in crop improvement. A greenhouse experiment was conducted to study the effect of 4 different irrigation water salinities (blank, 4, 8 and 12 dS m-1, prepared with 1:1 molar ratio of chlorides of calcium and sodium and magnesium sulphate salts. and 5 different zinc applications (0, 10, 20, 30 mg Kg-1 soil and foliar application of salt of zinc sulphate on yield, yield components and zinc concentration of wheat, using a completely randomized design, factorial with three replications. Plant height, spike length, 1000 grain weight, number of grain per spike, grain and straw yield was decreased by Irrigation water salinity. And all of these parameters were improved by zinc application except 1000 grain weight. Zinc absorption and concentration in straw and grain was decreased by Saline water compared to blank. And concentration of zinc significantly was increased in straw and grain by increase zinc application. The results indicated that, zinc application under low to medium salinity conditions improved growth and yield of wheat due to decreasing the impacts salinity.

  7. Application of Canal Automation at the Central Arizona Irrigation and Drainage District

    Science.gov (United States)

    The Central Arizona Irrigation and Drainage District (CAIDD) began delivering water to users in 1987. Although designed for automatic control, the system was run manually until a homemade SCADA (Supervisory Control and Data Acquisition) system was developed by a district employee. In 2002, problem...

  8. Regional application of one-dimensional water flow models for irrigation management

    NARCIS (Netherlands)

    Urso, D' G.; Menenti, M.; Santini, A.

    1999-01-01

    Numerical models for the simulation of soil water processes can be used to evaluate the spatial and temporal variations of crop water requirements; this information can support the irrigation management in a rationale usage of water resources. This latter objective requires the knowledge of

  9. Soil moisture and plant canopy temperature sensing for irrigation application in cotton

    Science.gov (United States)

    A wireless sensor network was deployed in a cotton field to monitor soil water status for irrigation. The network included two systems, a Decagon system and a microcontroller-based system. The Decagon system consists of soil volumetric water-content sensors, wireless data loggers, and a central data...

  10. Application of computer technique in SMCAMS

    International Nuclear Information System (INIS)

    Lu Deming

    2001-01-01

    A series of applications of computer technique in SMCAMS physics design and magnetic field measurement is described, including digital calculation of electric-magnetic field, beam dynamics, calculation of beam injection and extraction, and mapping and shaping of the magnetic field

  11. The Use of Different Irrigation Techniques to Decrease Bacterial Loads in Healthy and Diabetic Patients with Asymptomatic Apical Periodontitis

    Directory of Open Access Journals (Sweden)

    Mai Ghoneim

    2016-12-01

    CONCLUSION: The EndoVac can be considered as a promising tool in combination with irrigant solution to defeat the bacterial colonies living in the root canal system. Additional studies ought to be done to improve the means of bacterial clearance mainly in immune-compromised individuals.

  12. Effect of Irrigation CutOff on Flowering Stage and Foliar Application of Spermidine on Some Quantitative and Qualitative Characteristics of Various Ecotypes of Cumin

    Directory of Open Access Journals (Sweden)

    Sarah Bakhtari

    2017-02-01

    Full Text Available Introduction: Medicinal plants play major roles in human health. . Cumin (Cuminum cyminum L. is an annual plant that commonly cultivated in arid and semiarid regions of Iran. The crop has a wide range of uses including medicinal, cosmetic and food industry. Cumin occupies about 26% of the total area devoted to medicinal plants in Iran. However, cumin is seriously affected by the Fusarium wilt and blight diseases. The diseases usually increase under warm and wet conditions. It was demonstrated that the peak of the disease incidence is occurring at the flowering stage and irrigation cutoff at this time may be reduced the diseases density. Materials and methods: In order to evaluate the effects of irrigation cutoff in flowering stage and foliar application of spermidine on some characteristics of various ecotype of cumin, an experiment was conducted in a split-split-plot arrangement in randomized complete block design with three replications at the research farm of Shahid Bahonar University of Kerman at 2014. The experimental treatments were irrigation in two levels (complete irrigation and cutoff the irrigation in flowering stage assigned to main plots, foliar application of spermidine in three levels (0, 1 and 2 Mm as a subplot and cumin ecotypes in three levels (Kerman, Khorasan and Esfahan that was randomized in sub-subplot. Plots size under the trial was 4 m × 3 m so as to get 50 cm inter row spacing in six rows. The ideal density of the crops was considered as 120 plant m-2. As soon as the seeds were sown, irrigation was applied every 10 days. Foliar application of spermidine was done at three stages (after thinning, before flowering stage and in the middle of flowering stage. No herbicides and chemical fertilizers were applied during the expriments. Results and discussion: In this study the number of branches, umbels per plant, 1000-seed weight, seed yield per plant and hectare, harvest index, essential oil percentage and yield, infected

  13. Soft computing techniques in engineering applications

    CERN Document Server

    Zhong, Baojiang

    2014-01-01

    The Soft Computing techniques, which are based on the information processing of biological systems are now massively used in the area of pattern recognition, making prediction & planning, as well as acting on the environment. Ideally speaking, soft computing is not a subject of homogeneous concepts and techniques; rather, it is an amalgamation of distinct methods that confirms to its guiding principle. At present, the main aim of soft computing is to exploit the tolerance for imprecision and uncertainty to achieve tractability, robustness and low solutions cost. The principal constituents of soft computing techniques are probabilistic reasoning, fuzzy logic, neuro-computing, genetic algorithms, belief networks, chaotic systems, as well as learning theory. This book covers contributions from various authors to demonstrate the use of soft computing techniques in various applications of engineering.  

  14. Modeling and assessing field irrigation water use in a canal system of Hetao, upper Yellow River basin: Application to maize, sunflower and watermelon

    Science.gov (United States)

    Ren, Dongyang; Xu, Xu; Hao, Yuanyuan; Huang, Guanhua

    2016-01-01

    Water saving in irrigation is a key issue in the upper Yellow River basin. Excessive irrigation leads to water waste, water table rising and increased salinity. Land fragmentation associated with a large dispersion of crops adds to the agro-hydrological complexity of the irrigation system. The model HYDRUS-1D, coupled with the FAO-56 dual crop coefficient approach (dualKc), was applied to simulate the water and salt movement processes. Field experiments were conducted for maize, sunflower and watermelon crops in the command area of a typical irrigation canal system in Hetao Irrigation District during 2012 and 2013. The model was calibrated and validated in three crop fields using two-year experimental data. Simulations of soil moisture, salinity concentration and crop yield fitted well with the observations. The irrigation water use was then evaluated and results showed that large amounts of irrigation water percolated due to over-irrigation but their reuse through capillary rise was also quite large. That reuse was facilitated by the dispersion of crops throughout largely fragmented field, thus with fields reusing water percolated from nearby areas due to the rapid lateral migration of groundwater. Beneficial water use could be improved when taking this aspect into account, which was not considered in previous researches. The non-beneficial evaporation and salt accumulation into the root zone were found to significantly increase during non-growth periods due to the shallow water tables. It could be concluded that when applying water saving measures, close attention should be paid to cropping pattern distribution and groundwater control in association with irrigation scheduling and technique improvement.

  15. Gain-P: A new strategy to increase furrow irrigation efficiency

    International Nuclear Information System (INIS)

    Schmitz, G.H.; Wohling, T.; Paly, M. D.; Schutze, N.

    2007-01-01

    The new methodology GAIN-P combines Genetic Algorithms, Artificial Intelligence techniques and rigorous Process modeling for substantially improving irrigation efficiency. The new strategy simultaneously identifies optimal values of both scheduling and irrigation parameters for an entire growing season and can be applied to irrigation systems with adequate or deficit water supply. In this contribution, GAIN-P is applied to furrow irrigation tackling the more difficult subject of the more effective deficit irrigation. A physically -based hydrodynamic irrigation model is iteratively coupled with a 2D subsurface flow model for generating a database containing all realistically feasible scenarios of water application in furrow irrigation. It is used for training a problem-adapted artificial neural network based on self-organized maps, which in turn portrays the inverse solution of the hydrodynamic furrow irrigation model and thus enormously speeds up the overall performance of the complete optimization tool. Global optimization with genetic algorithm finds the schedule with maximum crop yield for the given water volume. The impact of different irrigation schedules on crop yield is calculated by the coupled furrow irrigation model which also simulates soil evaporation, precipitation and root water uptake by the plants over the whole growing seasons, as well as crop growth and yield. First results with the new optimization strategy show that GAIN-P has a high potential to increase irrigation efficiency. (author)

  16. Commercial Applications of X Ray Spectrometric Techniques

    International Nuclear Information System (INIS)

    Wegrzynek, D.

    2013-01-01

    In the 21st century, the X-ray fluorescence (XRF) technique is widely used in process control, industrial applications and for routine elemental analysis. The technique has a multielement capability capable of detecting elements with Z ≥ 10, with a few instruments capable of detecting also elements with Z ≥ 5. It is characterized by a non-destructive analysis process and relatively good detection limits, typically one part per million, for a wide range of elements. The first commercial XRF instruments were introduced to the market about 50 years ago. They were the wavelength dispersive X ray fluorescence (WDXRF) spectrometers utilizing Bragg’s law and reflection on crystal lattices for sequential elemental analysis of sample composition. The advances made in radiation detector technology, especially the introduction of semiconductor detectors, improvements in signal processing electronics, availability and exponential growth of personal computer market led to invention of energy dispersive X ray fluorescence (EDXRF) technique. The EDXRF is more cost effective as compared to WDXRF. It also allows for designing compact instruments. Such instruments can be easily tailored to the needs of different customers, integrated with industrial installations, and also miniaturized for the purpose of in-situ applications. The versatility of the technique has been confirmed in a spectacular way by using the XRF and X-ray spectrometric techniques, among few others, during the NASA and ESA missions in search for the evidence of life and presence of water on the surface of Mars. The XRF technique has achieved its strong position within the atomic spectroscopy group of analytical techniques not only due to its versatility but also due to relatively low running costs, as compared to the commonly used methods, e.g., atomic absorption spectrometry (AAS) or inductively coupled plasma atomic emission/mass spectrometry (ICP-AES/MS). Presently, the XRF technique together with X ray

  17. Commercial Applications of X Ray Spectrometric Techniques

    Energy Technology Data Exchange (ETDEWEB)

    Wegrzynek, D., E-mail: D.Wedgrznek@iaea.org [International Atomic Energy Agency, The IAEA Laboratories, Seibersdorf, Vienna (Austria)

    2013-07-15

    In the 21st century, the X-ray fluorescence (XRF) technique is widely used in process control, industrial applications and for routine elemental analysis. The technique has a multielement capability capable of detecting elements with Z {>=} 10, with a few instruments capable of detecting also elements with Z {>=} 5. It is characterized by a non-destructive analysis process and relatively good detection limits, typically one part per million, for a wide range of elements. The first commercial XRF instruments were introduced to the market about 50 years ago. They were the wavelength dispersive X ray fluorescence (WDXRF) spectrometers utilizing Bragg's law and reflection on crystal lattices for sequential elemental analysis of sample composition. The advances made in radiation detector technology, especially the introduction of semiconductor detectors, improvements in signal processing electronics, availability and exponential growth of personal computer market led to invention of energy dispersive X ray fluorescence (EDXRF) technique. The EDXRF is more cost effective as compared to WDXRF. It also allows for designing compact instruments. Such instruments can be easily tailored to the needs of different customers, integrated with industrial installations, and also miniaturized for the purpose of in-situ applications. The versatility of the technique has been confirmed in a spectacular way by using the XRF and X-ray spectrometric techniques, among few others, during the NASA and ESA missions in search for the evidence of life and presence of water on the surface of Mars. The XRF technique has achieved its strong position within the atomic spectroscopy group of analytical techniques not only due to its versatility but also due to relatively low running costs, as compared to the commonly used methods, e.g., atomic absorption spectrometry (AAS) or inductively coupled plasma atomic emission/mass spectrometry (ICP-AES/MS). Presently, the XRF technique together with X ray

  18. Development and applications of microanalytical techniques

    International Nuclear Information System (INIS)

    Cholewa, M.

    2005-05-01

    The development of new analytical techniques is an essential part of our everyday life and is dictated by strong progress in modern science and technology. Both these areas require more precise information about materials and processes involved. Due to these requirements we have been observing a rapid growth in the development of techniques that require both a high spatial resolution and high sensitivity. Modern analytical techniques provide an important interface between science and applications. The works presented in this habilitation thesis span the period of almost 20 years. During this time the author has been leading the development and applications of several new analytical and micro analytical techniques which have been documented in this thesis. This development has required development of ideas, strong leadership, organisational skills, organisation of funds and groups to carry out the necessary work. In chapter 3 the use of the PIXE and XANES techniques described an investigation of permeability for selected elements inside cells. It was important to develop new protocols for sample preparation and analysis and a large number of cells were necessary in order to obtain meaningful data. This development was closely associated with work presented in chapter 4 where the role of sample damage under the MeV ion beam bombardment was investigated. At that time we were the leading group in the world to perform such studies. Chapter 5 describes development of new analytical techniques and its possible applications. Development of the SIHF has been probably the most demanding and difficult project and was described in chapter 6 and it was closely related with development of a diamond detector described in chapter 7. A great part of these works were performed by the author at the Micro Analytical Research Centre (MARC) in the School of Physics at the University of Melbourne in Australia. However, some works were performed at GSI in Germany and BNL in USA. (author)

  19. Application of an infrared thermometer to the determination of the timing of irrigation

    International Nuclear Information System (INIS)

    Cho, T.; Yano, T.; Nakano, Y.

    1986-01-01

    It is well known that leaf temperature rises with increased crop water stress. This phenomenon is recognized as having the potential to yield information on irrigation scheduling. In this study, infrared thermometry was used to measure crop temperature remotely. The errors in measurements derived from incoming long-wave radiation and leaf emissivity were experimentally evaluated in relation to the reliability of three types of water stress indices using leaf temperature as the parameter. From consecutive measurements of the crop-air temperature difference, obvious changes in daily pattern could be detected as soil water became limited. This result showed that the crop-air temperature difference, although a simple index, can be used in irrigation timing

  20. Applications of nuclear techniques and research 1990

    International Nuclear Information System (INIS)

    1990-01-01

    The application of nuclear techniques, i.e. those techniques where use is made of isotopes and radiation, continues to contribute to progress in science, technology, agriculture, industry and medicine. Nuclear applications found their way into the IAEA's activities from the very beginning, and their promotion constitutes today a substantial fraction of the IAEA's Technical Co-operation and Research Contract Programmes. The 1990 selection is opened by a review of the role and function of the IAEA's Research Contract Programme, which is one of the Agency's most effective tools for promoting and developing nuclear applications. Applications in agriculture are covered in two articles dealing respectively with issues affecting the acceptance of food irradiation by governments, the food industry and consumers and with the use of radiation to induce plant mutation, a practical tool available to plant breeders in their effort to develop better quality crops. The following article deals with a typical nuclear application in medicine, i.e. the use of radionuclides in the diagnosis of lung diseases and in investigations related to the respiratory function. The use of environmental isotopes to assess the energy potential of geothermal fields is the next subject, a good example of nuclear methods applied to the evaluation of natural resources. The 1990 review concludes with a presentation prepared by the Third World Academy of Sciences on magnetic fusion research activity in the developing countries and its connection with the IAEA's own fusion programme

  1. Comparing the Effect of Continuous and Intermittent Irrigation Techniques on Complications of Arterial Catheter and Partial Thromboplastin Time in Patients Following Coronary Artery Bypass Grafting Surgery

    Directory of Open Access Journals (Sweden)

    Sedigheh Arta

    2017-04-01

    Full Text Available Background: Different approaches are available to irrigate the arterial catheter, such as continuous and intermittent techniques. However, there is a disagreement regarding the most appropriate method. Aim: this study aimed to compare the effect of two continuous and intermittent irrigation methods on complications of arterial catheter and partial thromboplastin time (PTT in patients with coronary artery bypass (CABG surgery. Method: This randomized clinical trial was conducted on 60 participants undergoing coronary artery bypass grafting surgery in open-heart surgery ICU at Imam Reza hospital in Mashhad, Iran, in 2016. In continuous group, the arterial catheter was continuously irrigated with heparin solution at the rate of 2cc/h, and in the intermittent group with a syringe containing 5cc heparin solution every 3 hours. In both groups, catheter was monitored and recorded every 3 hours (until 48 hours and 3 times from enrollment in terms of complications of partial thromboplastin time. Data were analyzed using SPSS version 16. Results: The findingsof independent t-test showed that the two groups are homogeneous in age (P =0.48. The result of Fisher's exact test revealed no significant difference between the two groups in terms of average incidence of complications during the first 24 hours (P=0.55 and second 24 hours (P=0.55 after catheterization. Also during the 48 hours after surgery, independent t-test results showed no statistically significant difference in partial thromboplastin time (P=0.53 between the two groups. Implications for Practice: According to the results of the research based on the lack of difference between continuous and intermittent irrigation methods up to 48 hours after catheter replacement in terms of arterial catheter complications, further long-term follow-up researches are recommended.

  2. Emerging wireless networks concepts, techniques and applications

    CERN Document Server

    Makaya, Christian

    2011-01-01

    An authoritative collection of research papers and surveys, Emerging Wireless Networks: Concepts, Techniques, and Applications explores recent developments in next-generation wireless networks (NGWNs) and mobile broadband networks technologies, including 4G (LTE, WiMAX), 3G (UMTS, HSPA), WiFi, mobile ad hoc networks, mesh networks, and wireless sensor networks. Focusing on improving the performance of wireless networks and provisioning better quality of service and quality of experience for users, it reports on the standards of different emerging wireless networks, applications, and service fr

  3. Soil Nutrient Availability, Plant Nutrient Uptake, and Wild Blueberry (Vaccinium angustifolium Ait. Yield in Response to N-Viro Biosolids and Irrigation Applications

    Directory of Open Access Journals (Sweden)

    Aitazaz A. Farooque

    2012-01-01

    Full Text Available We compared the impact of surface broadcasted N-Viro biosolids and inorganic fertilizer (16.5% Ammonium sulphate, 34.5% Diammonium phosphate, 4.5% Potash, and 44.5% s and/or clay filler applications on soil properties and nutrients, leaf nutrient concentration, and the fruit yield of lowbush blueberry under irrigated and nonirrigated conditions during 2008-2009 at Debert, NS, Canada. Application rates of N-Viro biosolids were more than double of inorganic fertilizer applied at a recommended N rate of 32 kg ha−1. The experimental treatments NI: N-Viro with irrigation, FI: inorganic fertilizer with irrigation, N: N-Viro without irrigation, and F: inorganic fertilizer without irrigation (control were replicated four times under a randomized complete block design. The NI treatment had the highest OM (6.68% followed by FI (6.32%, N (6.18%, and F (4.43% treatments during the year 2008. Similar trends were observed during 2009 with the highest soil OM values (5.50% for NI treatment. Supplemental irrigation resulted in a 21% increase in the ripe fruit yield. Nonsignificant effect of fertilizer treatments on most of the nutrient concentrations in soil and plant leaves, and on ripe fruits yield reflects that the performance of N-Viro was comparable with that of the inorganic fertilizer used in this study.

  4. Carbon Balance in an Irrigated Corn Field after Inorganic Fertilizer or Manure Application

    Science.gov (United States)

    Lentz, R. D.; Lehrsch, G. A.

    2014-12-01

    Little is known about inorganic fertilizer or manure effects on organic carbon (OC) and inorganic C (IC) losses from a furrow irrigated field, particularly in the context of other system C gains or losses. In 2003 and 2004, we measured dissolved organic and inorganic C (DOC, DIC), particulate OC and IC (POC, PIC) concentrations in irrigation inflow, runoff, and percolation waters (6-7 irrigations/y); C inputs from soil amendments and crop biomass; harvested C; and gaseous C emissions from field plots cropped to silage corn (Zea mays L.) in southern Idaho. Annual treatments included: (M) 13 (y 1) and 34 Mg/ha (y 2) stockpiled dairy manure; (F) 78 (yr 1) and 195 kg N/ha (y 2) inorganic N fertilizer; or (NA) no amendment--control. The mean annual total C input into M plots averaged 16.1 Mg/ha, 1.4-times greater than that for NA (11.5 Mg/ha) or F (11.1 Mg/ha), while total C outputs for the three treatments were similar, averaging 11.8 Mg/ha. Thus, the manure plots ended each growing season with an average net gain of 3.8 Mg C/ha (a positive net C flux), while the control (-0.5 Mg C/ha) and fertilizer (-0.4 Mg C/ha) treatments finished the season with a net C loss. Atmospheric CO2 incorporated into the crop biomass contributed 96% of the mean annual C input to NA and F plots but only 68% to M plots. We conclude that nutrient amendments substantially influence the short-term carbon balance of our furrow-irrigated system. Amendments had both direct and indirect influences on individual C components, such as the losses of DIC and POC in runoff and DOC in percolation water, producing temporally complex outcomes which may depend on environmental conditions external to the field.

  5. Comparative Study of Water and Nitrogen Fertilizer Application on Potato Crop under Fertigation and Surface Irrigating Systems by Using Labeled Nitrogen (15N)

    International Nuclear Information System (INIS)

    Abdullah Haidara, H. M.; Amin Alkirshi, A. H.; Saleh Husien, A.

    2007-01-01

    This research activity was conducted at Central Highland Research Station Farm-Dhamar, on potato Crop (Diamant cv.), during three seasons of 2000, 2001, and 2003.The objective of this activity was to study the Nitrogen Fertilizer Use Efficiency (WUE) which applied in different dosages with irrigation water (fertigation) and one dosage to the soil under surface irrigation, by using Labeled nitrogen fertilizer ( 15N ), comparing the quantity of irrigation water applied through Drip irrigation method and surface irrigation and its effect on WUE and yield of potato crop. The basic experiment was planted in randomized completely block design (RCBD) with five replications during 2000 season and six replication in 2001.and five treatments were tested (N1= 50kg N/ha, N2 =100kg N/ha, N3=150kg N/ha and N4=200kgN/ha as fertigated treatments under drip irrigation and Ns = 150kg N/ha as surface Nitrogen Application under surface irrigation. While in the 2003 season Verification trial was conducted with two replications, two treatments and RCB design. Results indicated that using Drip irrigation method in application of water saved 38% of irrigation water as compared to Surface irrigation. Fertigated treatments (N1, N2, N3 and N4) were, significantly superior to Surface Nitrogen Application treatment (NS), fertigated treatment (N3) gave the highest values of WUE which were 5.3, 6.4 and 6.1 kg/m3 for the three seasons (2000, 2001, 2003 respectively) with an average of 5.9 kg/m3 comparing to the surface Nitrogen Application treatment (NS) which gave the less yield per unit of water which was 3.8, 3.6 and 3.9 kg /m3 for the three seasons 2000, 2001 and 2003 respectively with an average of 3.7 kg/m3.The Average yield of potato tubers for (N3) treatment in the three seasons was 30 .3 t/ha comparing to the (NS) treatment, which gave an average of 29,5t/ha.The fertigatetd treatment (N1) recorded the highest efficient use of nitrogen Fertilizer followed by (N3) compare to the surface

  6. Industrial radiography techniques and their applications

    International Nuclear Information System (INIS)

    Wamorkar, R.R.

    1981-01-01

    Various aspects of industrial radiography are discussed. These include: radiation sources, geometrical unsharpness of image, radiation attenuation in the specimen, radiation effect of film, types of film, intensifying screens, exposure time calculations, source to film distance and sensivitity. Radiography techniques for examination of welded joints on flat plate and pipes or cylindrical objects, and castings are indicated. Applications of radiography in various industries are mentioned. (M.G.B.)

  7. Nuclear techniques to evaluate the water use of field crops irrigated in different stages of their cycles

    International Nuclear Information System (INIS)

    Libardi, P.L.; Moraes, S.O.; Saad, M.A.; Jong Van Lier, Q.; Vieira, O.; Luis Tuon, R.

    1995-01-01

    The search for soil - water management systems that rationalize the water use of field crops should always be emphasized. The present coordinated research programme of the joint division FAO/ AEA has the objective to contribute to a better understanding of this subject by improving the use efficiency of water resources in irrigated agriculture. This project is a contribution to this programme and consisted in the identification of specified development stages of bean ( phaseolus vulgaris, L ) and corn (Zea mays, L ) crops in which plants are less sensitive to water deficit. Experiments were carried out in a tropical soil of agricultural importance in a traditional irrigation field site of the state of Sao Paulo, Brazil. Neutron probe tensiometers were used to determine the soil water balance in different treatments. 3 tabs, 16 refs, (Author)

  8. Advanced flow MRI: emerging techniques and applications

    International Nuclear Information System (INIS)

    Markl, M.; Schnell, S.; Wu, C.; Bollache, E.; Jarvis, K.; Barker, A.J.; Robinson, J.D.; Rigsby, C.K.

    2016-01-01

    Magnetic resonance imaging (MRI) techniques provide non-invasive and non-ionising methods for the highly accurate anatomical depiction of the heart and vessels throughout the cardiac cycle. In addition, the intrinsic sensitivity of MRI to motion offers the unique ability to acquire spatially registered blood flow simultaneously with the morphological data, within a single measurement. In clinical routine, flow MRI is typically accomplished using methods that resolve two spatial dimensions in individual planes and encode the time-resolved velocity in one principal direction, typically oriented perpendicular to the two-dimensional (2D) section. This review describes recently developed advanced MRI flow techniques, which allow for more comprehensive evaluation of blood flow characteristics, such as real-time flow imaging, 2D multiple-venc phase contrast MRI, four-dimensional (4D) flow MRI, quantification of complex haemodynamic properties, and highly accelerated flow imaging. Emerging techniques and novel applications are explored. In addition, applications of these new techniques for the improved evaluation of cardiovascular (aorta, pulmonary arteries, congenital heart disease, atrial fibrillation, coronary arteries) as well as cerebrovascular disease (intra-cranial arteries and veins) are presented.

  9. Applications of neutron activation analysis technique

    International Nuclear Information System (INIS)

    Jonah, S. A.

    2000-07-01

    The technique was developed as far back as 1936 by G. Hevesy and H. Levy for the analysis of Dy using an isotopic source. Approximately 40 elements can be analyzed by instrumental neutron activation analysis (INNA) technique with neutrons from a nuclear reactor. By applying radiochemical separation, the number of elements that can be analysed may be increased to almost 70. Compared with other analytical methods used in environmental and industrial research, NAA has some unique features. These are multi-element capability, rapidity, reproducibility of results, complementarity to other methods, freedom from analytical blank and independency of chemical state of elements. There are several types of neutron sources namely: nuclear reactors, accelerator-based and radioisotope-based sources, but nuclear reactors with high fluxes of neutrons from the fission of 235 U give the most intense irradiation, and hence the highest available sensitivities for NAA. In this paper, the applications of NAA of socio-economic importance are discussed. The benefits of using NAA and related nuclear techniques for on-line applications in industrial process control are highlighted. A brief description of the NAA set-ups at CERT is enumerated. Finally, NAA is compared with other leading analytical techniques

  10. Rejection of organic micro-pollutants from water by a tubular, hydrophilic pervaporative membrane designed for irrigation applications.

    Science.gov (United States)

    Sule, May N; Templeton, Michael R; Bond, Tom

    2016-01-01

    The links between chemical properties, including those relating to molecular size, solubility, hydrophobicity and vapour pressure, and rejection of model aromatic micro-pollutants by a tubular, hydrophilic polymer pervaporation membrane designed for irrigation applications were investigated. Open air experiments were conducted at room temperature for individual solutions of fluorene, naphthalene, phenol, 1,2-dichlorobenzene, 1,2-diethylbenzene and 2-phenoxyethanol. Percentage rejection generally increased with increased molecular size for the model micro-pollutants (47-86%). Molecular weight and log Kow had the strongest positive relationships with rejection, as demonstrated by respective correlation coefficients of r = 0.898 and 0.824. Rejection was also strongly negatively correlated with aqueous solubility and H-bond δ. However, properties which relate to vapour phase concentrations of the micro-pollutants were not well correlated with rejection. Thus, physicochemical separation processes, rather than vapour pressure, drive removal of aromatic contaminants by the investigated pervaporation tube. This expanded knowledge could be utilized in considering practical applications of pervaporative irrigation systems for treating organic-contaminated waters such as oilfield-produced waters.

  11. Application of Azolla and intermittent irrigation to improve the productivity and nutrient contents of local black rice variety

    Science.gov (United States)

    Sulandjari; Yunindanova, M. B.

    2018-03-01

    Black rice is a local rice variety that contains a high level of anthocyanin pigment. Anthocyanin has been reported to be very effective in reducing cholesterol levels as well as cancer cell invasion. One of the main problems in rice cultivation is lack of water. System of Rice Intensification (SRI) has shown to be able to increase rice productivity by increasing the number of tillers. This system is known as a water-efficient cultivation. Other rice cultivation barrier is related to the use of nitrogen fertilizer. One of replacement of nitrogen fertilizer is by adding azolla. The objective of this research was identifying growth and yield of organic black rice with intermittent irrigation and application of azolla. The plant material used was black rice Cempo variety from Sleman, Yogyakarta. This experiment utilized 4 dosages of azolla as the first treatment: 100 gm-2, 200 gm-2 and 400 gm-2. The second treatment was water supply consisted of continuous flooded 2 cm; flooded 2 cm every 3 days; flooded 2 cm every 6 days. The results depicted that the application of azolla was able to increase the growth of black rice. Azolla of 200 gm-2 and 400 gm-2 and intermittent 3 days to 6 days generated higher dry grain, anthocyanin and antioxidant. Azolla 200 gm-2 with intermittent irrigation 3 days could be a good combination to improve plant growth, yield and properties of local black rice.

  12. Can deficit irrigation techniques be used to enhance phosphorus and water use efficiency and benefit crop yields?

    Science.gov (United States)

    Wright, Hannah R.; Dodd, Ian C.; Blackwell, Martin S. A.; Surridge, Ben W. J.

    2015-04-01

    Soil drying and rewetting (DRW) affects the forms and availability of phosphorus (P). Water soluble P has been reported to increase 1.8- to 19-fold after air-drying with the majority of the increase (56-100%) attributable to organic P. Similarly, in two contrasting soil types DRW increased concentrations of total P and reactive P in leachate, likely due to enhanced P mineralisation and physiochemical processes causing detachment of soil colloids, with faster rewetting rates related to higher concentrations of P. The intensity of drying as well as the rate of rewetting influences organic and inorganic P cycling. How these dynamics are driven by soil water status, and impact crop P acquisition and growth, remains unclear. Improving P and water use efficiencies and crop yields is globally important as both P and water resources become increasingly scarce, whilst demand for food increases. Irrigation supply below the water requirement for full crop evapotranspiration is employed by agricultural practitioners where water supply is limited. Regulated deficit irrigation describes the scheduling of water supply to correspond to the times of highest crop demand. Alternate wetting and drying (AWD) is applied in lowland irrigated rice production to avoid flooding at certain times of crop development, and has benefited P nutrition and yields. This research aims to optimise the benefits of P availability and uptake achieved by DRW by guiding deficit irrigation management strategies. Further determination of underlying processes driving P cycling at fluctuating soil moisture status is required. Presented here is a summary of the literature on DRW effects on soil P availability and plant P uptake and partitioning, in a range of soil types and cropping systems, with emphasis on alternate wetting and drying irrigation (AWD) compared to continuous flooding in lowland irrigated rice production. Soil water contents and matric potentials, and effects on P dynamics, are highly variable

  13. Effect of Zinc and Salicylic acid Foliar Application on Quantitative and Qualititative Characteristics of Soybean under Deficit Irrigation Conditions

    Directory of Open Access Journals (Sweden)

    Z Zarei

    2017-03-01

    Full Text Available Introduction Soybean (Glycine max (L. Merrill is a leguminous annual crop belonging to the Fabaceae family, that because an important source of food containing 20 to 28 grain oil percent and high protein is the most important oilseed of worldwide interest. Recently, cultivation of this plant is considered as a valuable oil plant in crop rotation. Drought, salinity, heat and freezing are environmental conditions that cause adverse effects on the growth of plants. Water deficit more than other stresses limits the growth of crops. Yield of soybean decreased due to drought stress. The consumption of fertilizers increases the quality of crops. According to the findings of Yasari and Vahedi (2012 use of Zn in soil and foliar application has an increasing effect on the percentage and the amount of oil and protein in soybean product. The role of salicylic acid (SA is reducing the effects of environmental stresses. It appears that water stress impairs plants and zinc alleviates water stress injuries. Thus, the purpose of this study was to evaluate the effect of water stress, zinc and salicylic acid foliar application on oil and grain protein percentage and their relation with oil and protein yield of soybean. Materials and Methods This study was carried out in the agricultural garden of Lorestan-Iran, in 2013. The meteorological data of the region are representing in Table 2. The soil was clay-loam texture (Table 1. The experiment was performed using Split factorial in a randomized complete block design with four replications. In this study, main factor was two levels of irrigation regimes: after 60 (optimum irrigation and 120 mm (stress evaporation from evaporation pan class A and subplot were considered combination of zinc foliar application (Zero and 1 L/ha, in two levels and salicylic acid (0, 0.5 and 1 mM. All statistical analyses were carried out using SAS software and the correlation was done using MSTAT-C program. Results and Discussion In the

  14. Effect of irrigation and timing and type of nitrogen application on the biochemical composition of Vitis vinifera L. cv. Chardonnay and Syrah grapeberries.

    Science.gov (United States)

    Canoura, Carolina; Kelly, Mary T; Ojeda, Hernan

    2018-02-15

    This study reports the effect of different doses of nitrogen applied to soil and/or leaves of Syrah and Chardonnay grapevines in the Languedoc-Roussillon (France) over two years. In 2011, nitrogen treatment involved both foliar urea sprayings and soil application at two different levels, with two controls - irrigated without nitrogen and no irrigation nor nitrogen. In 2012, the same grapevines received either soil or foliar nitrogen using the same controls. Results showed that foliar application increased the amino acid content to a greater extent than soil application, but that a combination of both was the most effective. For the first time, significantly elevated proline levels in response to drought were demonstrated for the grapevine. Increased contents of aromatic compounds and glycosylated precursors closely mirrored the applied nitrogen dose. Wines produced from N-fertilized Syrah grapes in 2011 showed a statistically significant effect of irrigation and fertilization on positive sensorial perception. Copyright © 2017 Elsevier Ltd. All rights reserved.

  15. Principles, Techniques, and Applications of Tissue Microfluidics

    Science.gov (United States)

    Wade, Lawrence A.; Kartalov, Emil P.; Shibata, Darryl; Taylor, Clive

    2011-01-01

    The principle of tissue microfluidics and its resultant techniques has been applied to cell analysis. Building microfluidics to suit a particular tissue sample would allow the rapid, reliable, inexpensive, highly parallelized, selective extraction of chosen regions of tissue for purposes of further biochemical analysis. Furthermore, the applicability of the techniques ranges beyond the described pathology application. For example, they would also allow the posing and successful answering of new sets of questions in many areas of fundamental research. The proposed integration of microfluidic techniques and tissue slice samples is called "tissue microfluidics" because it molds the microfluidic architectures in accordance with each particular structure of each specific tissue sample. Thus, microfluidics can be built around the tissues, following the tissue structure, or alternatively, the microfluidics can be adapted to the specific geometry of particular tissues. By contrast, the traditional approach is that microfluidic devices are structured in accordance with engineering considerations, while the biological components in applied devices are forced to comply with these engineering presets.

  16. Interactive data visualization foundations, techniques, and applications

    CERN Document Server

    Ward, Matthew; Keim, Daniel

    2010-01-01

    Visualization is the process of representing data, information, and knowledge in a visual form to support the tasks of exploration, confirmation, presentation, and understanding. This book is designed as a textbook for students, researchers, analysts, professionals, and designers of visualization techniques, tools, and systems. It covers the full spectrum of the field, including mathematical and analytical aspects, ranging from its foundations to human visual perception; from coded algorithms for different types of data, information and tasks to the design and evaluation of new visualization techniques. Sample programs are provided as starting points for building one's own visualization tools. Numerous data sets have been made available that highlight different application areas and allow readers to evaluate the strengths and weaknesses of different visualization methods. Exercises, programming projects, and related readings are given for each chapter. The book concludes with an examination of several existin...

  17. Applications Of Binary Image Analysis Techniques

    Science.gov (United States)

    Tropf, H.; Enderle, E.; Kammerer, H. P.

    1983-10-01

    After discussing the conditions where binary image analysis techniques can be used, three new applications of the fast binary image analysis system S.A.M. (Sensorsystem for Automation and Measurement) are reported: (1) The human view direction is measured at TV frame rate while the subject's head is free movable. (2) Industrial parts hanging on a moving conveyor are classified prior to spray painting by robot. (3) In automotive wheel assembly, the eccentricity of the wheel is minimized by turning the tyre relative to the rim in order to balance the eccentricity of the components.

  18. Multimedia encryption and authentication techniques and applications

    CERN Document Server

    Furht, Borko

    2006-01-01

    Intellectual property owners must continually exploit new ways of reproducing, distributing, and marketing their products. However, the threat of piracy looms as a major problem with digital distribution and storage technologies. Multimedia Encryption and Authentication Techniques and Applications covers current and future trends in the design of modern systems that use encryption and authentication to protect multimedia content. Containing the works of contributing authors who are worldwide experts in their fields, this volume is intended for researchers and practitioners, as well as for thos

  19. Nitrogen Recovered By Sorghum Plants As Affected By Saline Irrigation Water And Organic/Inorganic Resources Using 15N Technique

    International Nuclear Information System (INIS)

    ABOU-ELKHAIR, R.A.; EL-MOHTASEM, M.O.; SOLIMAN, S.M.; GALAL, Y.G.M.; ABD EL-LATIF, E.M.

    2009-01-01

    A pot experiment was conducted in the green house of Soil and Water Department, Nuclear Research Centre, Atomic Energy Authority, Egypt, to follow up the effect of saline irrigation water, inorganic and organic fertilizers on sorghum growth and N fractions that recovered by plant organs. Two types of artificial water salinity were used; one has 3 dS m -1 salinity level with 4 and 8 SAR and the second one has 3 and 6 dS m -1 salinity levels with 6 SAR . Leucenae residue and chicken manure were applied as organic sources at rate of 2% v/v. Sorghum was fertilized with recommended doses of super phosphate and potassium sulfate at rate of 150 kg P and 50 kg K per feddan, respectively. Labelled ammonium sulfate with 5% 15 N atom excess was applied to sorghum at rate of 100 kg N fed -1 . Dry matter yield (stalks and roots) was negatively affected by increasing water salinity levels or SAR ratios. Similar trend was recorded with N uptake by either stalks or roots of sorghum plants. On the other hand, both the dry matter yield and N uptake were positively and significantly affected by incorporation of organic sources in comparison to the untreated control. In this regard, the dry matter yield and N uptake induced by incorporation of chicken manure was superior over those recorded with leucenae residues. It means, in general, that the incorporation of organic sources into the soil may maximize the plant ability to combat the hazards effects caused by irrigation with saline water. Nitrogen derived from fertilizer (% Ndff), soil (% Ndfs) and organic resources (% Ndfr) showed frequent trends as affected by water salinity and organic resources but in most cases, severe reduction of these values was recorded when plants were irrigated with saline water. In the same time, plants were more dependent on N derived from organic sources than those derived from mineral fertilizer. Superiority of one organic source over the other was related to water salinity levels and SAR ratios

  20. High energy heavy ions: techniques and applications

    International Nuclear Information System (INIS)

    Alonso, J.R.

    1985-04-01

    Pioneering work at the Bevalac has given significant insight into the field of relativistic heavy ions, both in the development of techniques for acceleration and delivery of these beams as well as in many novel areas of applications. This paper will outline our experiences at the Bevalac; ion sources, low velocity acceleration, matching to the synchrotron booster, and beam delivery. Applications discussed will include the observation of new effects in central nuclear collisions, production of beams of exotic short-lived (down to 1 μsec) isotopes through peripheral nuclear collisions, atomic physics with hydrogen-like uranium ions, effects of heavy ''cosmic rays'' on satellite equipment, and an ongoing cancer radiotherapy program with heavy ions. 39 refs., 6 figs., 1 tab

  1. Optimization Strategy for Improving the Energy Efficiency of Irrigation Systems by Micro Hydropower: Practical Application

    Directory of Open Access Journals (Sweden)

    Modesto Pérez-Sánchez

    2017-10-01

    Full Text Available Analyses of possible synergies between energy recovery and water management are essential for achieving sustainable advances in the performance of pressurized irrigation networks. Nowadays, the use of micro hydropower in water systems is being analysed to improve the overall energy efficiency. In this line, the present research is focused on the proposal and development of a novel optimization strategy for increasing the energy efficiency in pressurized irrigation networks by energy recovering. The recovered energy is maximized considering different objective functions, including feasibility index: the best energy converter must be selected, operating in its best efficiency conditions by variation of its rotational speed, providing the required flow in each moment. These flows (previously estimated through farmers’ habits are compared with registered values of flow in the main line with very suitable calibration results, getting a Nash–Sutcliffe value above 0.6 for different time intervals, and a PBIAS index below 10% in all time interval range. The methodology was applied to a Vallada network obtaining a maximum recovered energy of 58.18 MWh/year (41.66% of the available energy, improving the recovered energy values between 141 and 184% when comparing to energy recovery considering a constant rotational speed. The proposal of this strategy shows the real possibility of installing micro hydropower machines to improve the water–energy nexus management in pressurized systems.

  2. Physiological and biochemical responses to the exogenous application of proline of tomato plants irrigated with saline water

    Directory of Open Access Journals (Sweden)

    B. Kahlaoui

    2018-01-01

    Full Text Available In scope of crop salinity tolerance, an experiment was carried out in a field using saline water (6.57 dS m−1 and subsurface drip irrigation (SDI on two tomato cultivars (Solanum lycopersicum, cv. Rio Grande and Heinz-2274 in a salty clay soil. Exogenous application of proline was done by foliar spray at two concentrations: 10 and 20 mg L−1, with a control (saline water without proline, during the flowering stage. Significant higher increases in proline and total soluble protein contents, glutamine synthetase (GS, EC6.3.1.2 activities and decreases in proline oxidase (l-proline: O2 Oxidoreductase, EC1.4.3.1 activities were detected in both tomato cultivars when irrigated with saline water (6.57 dS m−1 and exogenously applied by the lower concentration of proline. Taking in consideration the obtained results, it was concluded that the foliar spray of low concentration of proline can increase the tolerance of both cultivars of tomato to salinity under field conditions.

  3. Farm-based measures for reducing microbiological health risks for consumers from informal wastewater-irrigated agriculture

    DEFF Research Database (Denmark)

    Keraita, Bernard; Konradsen, Flemming; Drechsel, Pay

    2010-01-01

    in developing countries as part of a multiple-barrier approach for health-risk reduction along the farm to fork pathway. Measures discussed include treatment of irrigation water using ponds, filters and wetland systems; water application techniques; irrigation scheduling; and crop selection. In addition...

  4. Acoustic emission technique and its applications

    International Nuclear Information System (INIS)

    Sato, Ichiya; Sasaki, Soji

    1976-01-01

    Acoustic emission technique is described. The characteristics of acoustic emission signal, measurement techniques, and its application are explained. The acoustic signals are grouped into continuous and burst types. The continuous signal is due to plastic deformation, and the burst type is due to the generation and growth of cracks. The latter can be used for the identification of the position of cracks. The frequency of the acoustic emission is in the range from several tens of KHz to two MHz. Piezoelectric ceramics are used as the oscillators of sensors. The dynamic behavior of acoustic emission can be observed with a two-channel acoustic emission measuring apparatus. Multi-channel method was developed at Hitachi, Ltd., and is used for large structures. General computer identification method and simple zone identification method are explained. Noise elimination is important for the measurement, and the methods were studied. Examples of application are the observation of acoustic emission in the plastic deformation of steel, the tensile test of large welded material with natural defects, and others. The method will be used for the diagnosis and observation of large structures, the test and quality control of products. (Kato, T.)

  5. Conserving energy through new irrigation technologies. Technical briefing report

    Energy Technology Data Exchange (ETDEWEB)

    1982-07-01

    The benefits and applications of five irrigation technologies are explored: mobile drop-tube irrigation, computerized scheduling, reduced-pressure center pivots, well design and development, and automated gated-pipe systems. Perhaps the most promising of the new irrigation technologies is the low-energy, precision-application (LEPA) system. This mobile system used one-half the energy of conventional sprinkler systems and distributes water with greater efficiency through a series of low-pressure drop tubes suspended above the crop. Computerized methods of irrigation scheduling have been developed to help farmers conserve water and energy. Special computer programs determine when a crop needs water and how much to apply for optimal plant growth, thus preventing the unnecessary costs of pumping more water than the crop needs. Field test results show that replacing traditional scheduling methods of irrigation with computerized scheduling can reduce energy and water use by as much as 35%. The irrigation industry is actively promoting reduced-pressure water application methods, particularly for center-pivot systems. Reduced-pressure systems expend less energy but produce the same crop yields as conventional high-pressure systems, as long as excessive water runoff does not occur. If well design and development techniques are applied when a well is drilled into an unconsolidated acquifer, the well's life expectancy, as well as its operating efficiency, can increase, the later by as much as 40%.

  6. Studies and Application of Remote Sensing Retrieval Method of Soil Moisture Content in Land Parcel Units in Irrigation Area

    Science.gov (United States)

    Zhu, H.; Zhao, H. L.; Jiang, Y. Z.; Zang, W. B.

    2018-05-01

    Soil moisture is one of the important hydrological elements. Obtaining soil moisture accurately and effectively is of great significance for water resource management in irrigation area. During the process of soil moisture content retrieval with multiremote sensing data, multi- remote sensing data always brings multi-spatial scale problems which results in inconformity of soil moisture content retrieved by remote sensing in different spatial scale. In addition, agricultural water use management has suitable spatial scale of soil moisture information so as to satisfy the demands of dynamic management of water use and water demand in certain unit. We have proposed to use land parcel unit as the minimum unit to do soil moisture content research in agricultural water using area, according to soil characteristics, vegetation coverage characteristics in underlying layer, and hydrological characteristic into the basis of study unit division. We have proposed division method of land parcel units. Based on multi thermal infrared and near infrared remote sensing data, we calculate the ndvi and tvdi index and make a statistical model between the tvdi index and soil moisture of ground monitoring station. Then we move forward to study soil moisture remote sensing retrieval method on land parcel unit scale. And the method has been applied in Hetao irrigation area. Results show that compared with pixel scale the soil moisture content in land parcel unit scale has displayed stronger correlation with true value. Hence, remote sensing retrieval method of soil moisture content in land parcel unit scale has shown good applicability in Hetao irrigation area. We converted the research unit into the scale of land parcel unit. Using the land parcel units with unified crops and soil attributes as the research units more complies with the characteristics of agricultural water areas, avoids the problems such as decomposition of mixed pixels and excessive dependence on high-resolution data

  7. Additive manufacturing techniques and their biomedical applications

    Directory of Open Access Journals (Sweden)

    Yujing Liu

    2017-12-01

    Full Text Available Additive manufacturing (AM, also known as three-dimensional (3D printing, is gaining increasing attention in medical fields, especially in dental and implant areas. Because AM technologies have many advantages in comparison with traditional technologies, such as the ability to manufacture patient-specific complex components, high material utilization, support of tissue growth, and a unique customized service for individual patients, AM is considered to have a large potential market in medical fields. This brief review presents the recent progress of 3D-printed biomedical materials for bone applications, mainly for metallic materials, including multifunctional alloys with high strength and low Young’s modulus, shape memory alloys, and their 3D fabrication by AM technologies. It describes the potential of 3D printing techniques in precision medicine and community health.

  8. Radiolabelled blood elements techniques and clinical applications

    International Nuclear Information System (INIS)

    Thakur, M.L.

    1992-01-01

    Over the past few years, in nuclear medicine, the diagnostic applications of radiolabelled blood elements in general, and of radiolabelled white blood cells in particular, have become increasingly popular. This is primarily due to the introduction of lipid soluble 111 In-oxine as an agent, which not only is an excellent and a reliable tracer for blood cells but also enables the investigators to study the in vivo cell kinetics and map the localization of labelled cells by external gamma scintigraphy. The tracer has the modest half life of 67 hours and decays with the emission of two gamma photons (173 and 247 keV) in high abundance. This technique has provided a powerful tool to study the in vivo cell kinetics in health and localize abnormal lesions in diseases which invoke intense focal cellular concentration

  9. Radiolabelled blood elements techniques and clinical applications

    Energy Technology Data Exchange (ETDEWEB)

    Thakur, M L

    1993-12-31

    Over the past few years, in nuclear medicine, the diagnostic applications of radiolabelled blood elements in general, and of radiolabelled white blood cells in particular, have become increasingly popular. This is primarily due to the introduction of lipid soluble {sup 111}In-oxine as an agent, which not only is an excellent and a reliable tracer for blood cells but also enables the investigators to study the in vivo cell kinetics and map the localization of labelled cells by external gamma scintigraphy. The tracer has the modest half life of 67 hours and decays with the emission of two gamma photons (173 and 247 keV) in high abundance. This technique has provided a powerful tool to study the in vivo cell kinetics in health and localize abnormal lesions in diseases which invoke intense focal cellular concentration 5 figs, 2 tabs

  10. Confocal fluorescence techniques in industrial application

    Science.gov (United States)

    Eggeling, Christian; Gall, Karsten; Palo, Kaupo; Kask, Peet; Brand, Leif

    2003-06-01

    The FCS+plus family of evaluation tools for confocal fluorescence spectroscopy, which was developed during recent years, offers a comprehensive view to a series of fluorescence properties. Originating in fluorescence correlation spectroscopy (FCS) and using similar experimental equipment, a system of signal processing methods such as fluorescence intensity distribution analysis (FIDA) was created to analyze in detail the fluctuation behavior of fluorescent particles within a small area of detection. Giving simultaneous access to molecular parameters like concentration, translational and rotational diffusion, molecular brightness, and multicolor coincidence, this portfolio was enhanced by more traditional techniques of fluorescence lifetime as well as time-resolved anisotropy determination. The cornerstones of the FCS+plus methodology will be shortly described. The inhibition of a phosphatase enzyme activity gives a comprehensive industrial application that demonstrates FCS+plus' versatility and its potential for pharmaceutical drug discovery.

  11. Performances du goutte à goutte enterré pour l’irrigation de jeunes palmiers dattiers

    Directory of Open Access Journals (Sweden)

    R. BOURZIZA

    2017-03-01

    Full Text Available In oasis areas, surface water resources are becoming increasingly scarce. Groundwater resources are often overexploited, and are of poor quality for their high salinity degree. Water conservation and economy have therefore become imperative for better oases durability. If localized irrigation is currently recommended in Morocco for saving water, its use in the sub-desert areas does not keep water safe from high evaporation rates. An alternative to this system would be the use of subsurface drip irrigation. This technique is defined as an application of water under soil surface through drippers, which discharge water at generally similar rates as the surface drip irrigation. As subsurface drip irrigation is a newly introduced technique in Morocco, a better understanding in local conditions of the infiltration process around a buried source, and its impact on plant growth is necessarily required. This study aims to contribute to improving the efficiency of water use by testing the performance of subsurface drip irrigation system, especially in areas where water is a limited resource. The objectives of this research are performance evaluation in arid conditions of the subsurface drip irrigation system for young date palms compared to the surface drip, as well as determining the appropriate method of flow measurement for a buried dripper. In this context, an experimental plot was installed on a farm in the region of Erfoud (Errachidia Province, Southeast Morocco to characterize the respective performances of surface and subsurface drip irrigation on young date palm. Flow measurement to calculate the uniformity of the application of water was done through two methods: a flow measurement of drippers above the surface and another one underground. The latter method has also helped us to estimate losses through evaporation for both irrigation techniques. In addition, in order to compare the effect of two irrigation modes, plants were identified at random

  12. Neutron radiographic techniques, facilities and applications

    International Nuclear Information System (INIS)

    Domanus, J.C.

    1984-08-01

    This is a collection of three papers, written for presentation on two international conferences. The first paper: ''Neutron radiography. Techniques and facilities'', written by J.P. Barton of N-Ray Engineering Co. La Jolla, CA., USA and J.C. Domanus was presented at the International Symposium on the Use and Development of Low and Medium Flux Research Reactors at the Massachusets Institute of Technology, Cambridge, Mass., USA, 16-19 October 1983. The second paper: ''Neutron radiography with the DR-1 reactor at Risoe National Laboratory'', written by J.C. Domanus, was presented at the same Symposium. The third paper: ''Defects in nuclear fuel revealed by neutron radiography'', written by J.C. Domanus is accepted for presentation on 18 October 1984 to the 3rd European Conference on Nondestructive Testing, Florence, Italy, 15-18 October 1984. While the first paper describes the principles of neutron radiographic techniques and facilities, the second one describes an example of such facility and the third gives an example of application of neutron radiography in the field of nuclear fuel. (author)

  13. Background Characterization Techniques For Pattern Recognition Applications

    Science.gov (United States)

    Noah, Meg A.; Noah, Paul V.; Schroeder, John W.; Kessler, Bernard V.; Chernick, Julian A.

    1989-08-01

    The Department of Defense has a requirement to investigate technologies for the detection of air and ground vehicles in a clutter environment. The use of autonomous systems using infrared, visible, and millimeter wave detectors has the potential to meet DOD's needs. In general, however, the hard-ware technology (large detector arrays with high sensitivity) has outpaced the development of processing techniques and software. In a complex background scene the "problem" is as much one of clutter rejection as it is target detection. The work described in this paper has investigated a new, and innovative, methodology for background clutter characterization, target detection and target identification. The approach uses multivariate statistical analysis to evaluate a set of image metrics applied to infrared cloud imagery and terrain clutter scenes. The techniques are applied to two distinct problems: the characterization of atmospheric water vapor cloud scenes for the Navy's Infrared Search and Track (IRST) applications to support the Infrared Modeling Measurement and Analysis Program (IRAMMP); and the detection of ground vehicles for the Army's Autonomous Homing Munitions (AHM) problems. This work was sponsored under two separate Small Business Innovative Research (SBIR) programs by the Naval Surface Warfare Center (NSWC), White Oak MD, and the Army Material Systems Analysis Activity at Aberdeen Proving Ground MD. The software described in this paper will be available from the respective contract technical representatives.

  14. E12 sheet plastination: Techniques and applications.

    Science.gov (United States)

    Ottone, Nicolas Ernesto; Baptista, Carlos A C; Latorre, Rafael; Bianchi, Homero Felipe; Del Sol, Mariano; Fuentes, Ramon

    2017-10-30

    Plastination is an anatomical technique that consists of replacing the liquids and fat of specimens by reactive polymers through forced impregnation in a vacuum. These are then polymerized to achieve the final result. E12 sheet plastination involves epoxy resin impregnation of thin (2-4 mm) and ultra-thin (SciELO databases, and manual searches. After searching, 616 records were found using the online and manual searches (MEDLINE, n: 207; EMBASE, n: 346; SciELO, n: 44; Manual search: 23). Finally, 96 records were included in this review (after duplicates and articles unrelated to the subject were excluded). The aim of this work was to review the E12 sheet plastination technique, searching for articles concerning views of it, identifying the different variants implemented by researchers since its creation by Gunther von Hagens, and to identify its applications from teaching and research in anatomy to morphological sciences. Clin. Anat., 2017. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

  15. MR urography: examination techniques and clinical applications

    Energy Technology Data Exchange (ETDEWEB)

    Nolte-Ernsting, C.C.A.; Adam, G.B.; Guenther, R.W. [Technische Hochschule Aachen (Germany). Klinik fuer Radiologische Diagnostik

    2001-03-01

    Modern MR urography is performed on the basis of two different imaging strategies, which can be used complementarily to cover almost all aspects in the diagnosis of upper urinary tract diseases. The first technique utilizes unenhanced, heavily T2-weighted pulse sequences to obtain static-fluid images of the urinary tract. T2-weighted MR urograms have proved to be excellent in the visualization of the markedly dilated urinary tract, even if the renal excretory function is quiescent. Static-fluid MR urography is less suitable for imaging of disorders that occur in the nondilated collecting system. The second MR urography technique is analogous to the methodology of conventional intravenous pyelography and is, therefore, designated as excretory MR urography. For this purpose, a non-nephrotoxic gadolinium chelate is intravenously administered and after its renal excretion, the gadolinium-enhanced urine is visualized using fast T1-weighted gradient-echo sequences. The combination of gadolinium and low-dose furosemide (5-10 mg) is the key for achieving a uniform distribution of the contrast material inside the entire urinary tract and, secondly, to avoid high endoluminal gadolinium concentrations, which cause signal loss of the urine due to T2{sup *} effects. Gadolinium excretory MR urography allows to obtain high-quality images of both nondilated and obstructed urinary tracts in patients with normal or moderately impaired renal function. This article reviews the principles of T2- and T1-weighted MR urography in detail and informs how to use these techniques safely in potential clinical applications such as chronic urolithiasis, intrinsic and extrinsic tumor diseases, and congenital anomalies. Magnetic resonance urography performed in combination with standard MR imaging offers a potential to reduce the need for invasive retrograde pyelography. Although the economic aspect is still problematic, it is obvious that MR urography will continue to increase its role in

  16. Nitrogen use efficiencies of drip-irrigated tomatoes and peppers as affected by soil application and fertigation

    International Nuclear Information System (INIS)

    Elinc, F.; Deviren, A.; Oeztuerk, A.; Besiroglu, A.

    1996-01-01

    This greenhouse study conducted on a Mediterranean Terra Rose soil in an unheated plastic greenhouse was designed to investigate the response of drip-irrigated tomatoes (Lycopersicon esculentum Mill.) and peppers (Capsicum annum) to four nitrogen levels continually applied with irrigation stream. Water containing 0,67,134 or 201 mgN/l and uniformly supplied with 80 and 240 mg/l of P and K, respectively, were applied two times a week. Three adjacent plants in each plot were fertigated with N 15 labeled NH 4 S 2 O 4 (2% a.e. enrichment). For each plant the amount of water, P, K and the N 15 applied through the bottles was to that amount applied through a single dripper. In addition to the fertigation soil application of 400 kgN/ha was included with three adjacent plants in each plot were fertilized receiving N 15 labeled (3.3 % a.e. enrichment) The total amount of water applied was 392 mm and the resulting N application totals ranged from 200 to 600 kgN/ha. According to the results obtained, the maximum yield of tomatoes and peppers were achieved with 67 mgN/l (200 kgN/ha) treatment. The percentage fertilizer utilization by tomatoes was highest with 67 mgN/l (200 kgN/ha), which was followed by 134 mgN/l (400 kgN/ha) .The percentage fertilizer utilization was the lowest with 201 mgN/l (600 kgN/ha) or soil application (400 kgN/ha). The results indicated that the percentage fertilizer utilization of tomatoes was significantly greater by the fertigation than the soil application of N at the same level fertilization (400 kgN/ha). The fertilizer N uptake by peppers was significantly greater with 134 mgN/l (400 kgN/ha) than the other applications. The results indicated that although the percentage fertilizer utilization was the same, the fertilizer N uptake by peppers was significantly greater with the fertigation than the soil application of N at the same level fertilization (400 kgN/ha)

  17. Recent applications of nuclear track emulsion technique

    Energy Technology Data Exchange (ETDEWEB)

    Zarubin, P. I., E-mail: zarubin@lhe.jinr.ru [Joint Institute for Nuclear Research, Veksler and Baldin Laboratory of High Energy Physics (Russian Federation)

    2016-12-15

    A survey of recent results obtained using the nuclear track emulsion (NTE) technique in low energy applications is given. NTE irradiation with 60 MeV {sup 8}He nuclei provides identification of their decays at stopping, evaluation of the possibility of α range spectrometry, and observation of drift of thermalized {sup 8}He atoms. Correlations of α particles studied in {sup 12}C → 3α splitting induced by 14.1 MeV neutrons indicate the presence of a superposition of 0{sup +} and 2{sup +} states of the {sup 8}Be nucleus in the ground state of {sup 12}C. Angular correlations of fragments are studied in boron-enriched NTE, and the prospects of NTE application in radioactivity and nuclear fission research are discussed. It is proposed to use an automated microscope to search for collinear tripartition of heavy nuclei implanted in NTE. Surface irradiation of NTE by a {sup 252}Cf source is started. Planar events containing fragment pairs and long range α particles, as well as fragment triples, are studied. NTE samples are calibrated using Kr and Xe ions with an energy of 1.2 and 3 A MeV.

  18. Application of Electroporation Technique in Biofuel Processing

    Directory of Open Access Journals (Sweden)

    Yousuf Abu

    2017-01-01

    Full Text Available Biofuels production is mostly oriented with fermentation process, which requires fermentable sugar as nutrient for microbial growth. Lignocellulosic biomass (LCB represents the most attractive, low-cost feedstock for biofuel production, it is now arousing great interest. The cellulose that is embedded in the lignin matrix has an insoluble, highly-crystalline structure, so it is difficult to hydrolyze into fermentable sugar or cell protein. On the other hand, microbial lipid has been studying as substitute of plant oils or animal fat to produce biodiesel. It is still a great challenge to extract maximum lipid from microbial cells (yeast, fungi, algae investing minimum energy.Electroporation (EP of LCB results a significant increase in cell conductivity and permeability caused due to the application of an external electric field. EP is required to alter the size and structure of the biomass, to reduce the cellulose crystallinity, and increase their porosity as well as chemical composition, so that the hydrolysis of the carbohydrate fraction to monomeric sugars can be achieved rapidly and with greater yields. Furthermore, EP has a great potential to disrupt the microbial cell walls within few seconds to bring out the intracellular materials (lipid to the solution. Therefore, this study aims to describe the challenges and prospect of application of EP technique in biofuels processing.

  19. Application of fieldbus techniques in nuclear power plants

    International Nuclear Information System (INIS)

    Wang Xu; Chen Hang; Yu Shuxin; Zhang Xinli

    2012-01-01

    The successful application experience of fieldbus techniques in thermal power plants and nuclear power plants are outlined first. And then, the application of fieldbus techniques in domestic 3rd-generation nuclear power plant (NPP) project is discussed. After that, the solution to the potential problems of fieldbus techniques application in NPP is provided. (authors)

  20. Changes in fine-root production, phenology and spatial distribution in response to N application in irrigated sweet cherry trees.

    Science.gov (United States)

    Artacho, Pamela; Bonomelli, Claudia

    2016-05-01

    Factors regulating fine-root growth are poorly understood, particularly in fruit tree species. In this context, the effects of N addition on the temporal and spatial distribution of fine-root growth and on the fine-root turnover were assessed in irrigated sweet cherry trees. The influence of other exogenous and endogenous factors was also examined. The rhizotron technique was used to measure the length-based fine-root growth in trees fertilized at two N rates (0 and 60 kg ha(-1)), and the above-ground growth, leaf net assimilation, and air and soil variables were simultaneously monitored. N fertilization exerted a basal effect throughout the season, changing the magnitude, temporal patterns and spatial distribution of fine-root production and mortality. Specifically, N addition enhanced the total fine-root production by increasing rates and extending the production period. On average, N-fertilized trees had a length-based production that was 110-180% higher than in control trees, depending on growing season. Mortality was proportional to production, but turnover rates were inconsistently affected. Root production and mortality was homogeneously distributed in the soil profile of N-fertilized trees while control trees had 70-80% of the total fine-root production and mortality concentrated below 50 cm depth. Root mortality rates were associated with soil temperature and water content. In contrast, root production rates were primarily under endogenous control, specifically through source-sink relationships, which in turn were affected by N supply through changes in leaf photosynthetic level. Therefore, exogenous and endogenous factors interacted to control the fine-root dynamics of irrigated sweet cherry trees. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  1. Using Audience Segmentation to Tailor Residential Irrigation Water Conservation Programs

    Science.gov (United States)

    Warner, Laura A.; Chaudhary, Anil Kumar; Rumble, Joy N.; Lamm, Alexa J.; Momol, Esen

    2017-01-01

    Today's complex issues require technical expertise as well as the application of innovative social science techniques within Extension contexts. Researchers have suggested that a social science approach will play a critical role in water conservation, and people who use home landscape irrigation comprise a critical target audience for agriculture…

  2. Effects of foliar application of inactivated yeast on the phenolic composition of Vitis vinifera L. cv. Agiorgitiko grapes under different irrigation levels

    Directory of Open Access Journals (Sweden)

    Kogkou C

    2017-05-01

    Full Text Available Charikleia Kogkou,1 Evangelia Chorti,2 Maria Kyraleou,1 Stamatina Kallithraka,1 Stefanos Koundouras,3 Gerard Logan,1 Ioannis Kanakis,4 Yorgos Kotseridis1 1Laboratory of Enology, Department of Food Science and Technology, Agricultural University of Athens, Athens, Greece; 2Cooperative Winery of Nemea, Nemea, Greece; 3Laboratory of Viticulture, School of Agriculture, Aristotle University of Thessaloniki, Thessaloniki, Greece; 4Fassoulis Grapevine Nurseries, Nemea, Greece Abstract: Recent climate changes have caused the rising of average growing season temperatures leading to the advancement of vine phenological stages and to earlier harvests. This could result in the production of grapes with advanced berry sugar accumulation, but incomplete phenolic ripeness, thereby jeopardizing wine quality. This study aims to evaluate the effects of the application of a new product consisting of yeast derivatives on the phenolic maturity and composition of Agiorgitiko grapes and wines, under contrasting water conditions. The experiment was arranged as a 2×2 factorial design in a commercial vineyard situated in southern Greece, combining foliar spraying with LalVigne® Mature (two applications after veraison and an untreated control and water conditions (deficit irrigation and nonirrigated. Irrigation accelerated berry sugar accumulation, increased berry weight and anthocyanin content, and decreased skin tannin concentration. Spraying with yeast derivatives did not affect phenolic content of berry components, and it had no effect on must attributes. Foliar application of yeast derivatives resulted in a higher phenolic potential of the produced wines, only when combined with irrigation. Keywords: foliar spray, deficit irrigation, phenolic maturity, anthocyanins, tannins

  3. Techniques and Applications of Urban Data Analysis

    KAUST Repository

    AlHalawani, Sawsan N.

    2016-05-26

    Digitization and characterization of urban spaces are essential components as we move to an ever-growing ’always connected’ world. Accurate analysis of such digital urban spaces has become more important as we continue to get spatial and social context-aware feedback and recommendations in our daily activities. Modeling and reconstruction of urban environments have thus gained unprecedented importance in the last few years. Such analysis typically spans multiple disciplines, such as computer graphics, and computer vision as well as architecture, geoscience, and remote sensing. Reconstructing an urban environment usually requires an entire pipeline consisting of different tasks. In such a pipeline, data analysis plays a strong role in acquiring meaningful insights from the raw data. This dissertation primarily focuses on the analysis of various forms of urban data and proposes a set of techniques to extract useful information, which is then used for different applications. The first part of this dissertation presents a semi-automatic framework to analyze facade images to recover individual windows along with their functional configurations such as open or (partially) closed states. The main advantage of recovering both the repetition patterns of windows and their individual deformation parameters is to produce a factored facade representation. Such a factored representation enables a range of applications including interactive facade images, improved multi-view stereo reconstruction, facade-level change detection, and novel image editing possibilities. The second part of this dissertation demonstrates the importance of a layout configuration on its performance. As a specific application scenario, I investigate the interior layout of warehouses wherein the goal is to assign items to their storage locations while reducing flow congestion and enhancing the speed of order picking processes. The third part of the dissertation proposes a method to classify cities

  4. Applications of Electromigration Techniques: Applications of Electromigration Techniques in Food Analysis

    Science.gov (United States)

    Wieczorek, Piotr; Ligor, Magdalena; Buszewski, Bogusław

    Electromigration techniques, including capillary electrophoresis (CE), are widely used for separation and identification of compounds present in food products. These techniques may also be considered as alternate and complementary with respect to commonly used analytical techniques, such as high-performance liquid chromatography (HPLC), or gas chromatography (GC). Applications of CE concern the determination of high-molecular compounds, like polyphenols, including flavonoids, pigments, vitamins, food additives (preservatives, antioxidants, sweeteners, artificial pigments) are presented. Also, the method developed for the determination of proteins and peptides composed of amino acids, which are basic components of food products, are studied. Other substances such as carbohydrates, nucleic acids, biogenic amines, natural toxins, and other contaminations including pesticides and antibiotics are discussed. The possibility of CE application in food control laboratories, where analysis of the composition of food and food products are conducted, is of great importance. CE technique may be used during the control of technological processes in the food industry and for the identification of numerous compounds present in food. Due to the numerous advantages of the CE technique it is successfully used in routine food analysis.

  5. Effect of soil contamination due to wastewater irrigation on total cesium as determined by destructive and nondestructive analytical techniques in some soils of egypt

    International Nuclear Information System (INIS)

    Abdel-Sabour, M.F.; Abdel-Lattif, A.

    2005-01-01

    Fifteen soil samples were chosen from different locations to represent different soils irrigated with different sources of contaminated wastewater (sewage and industrial effluent). Sequential extraction experiment was carried out to determine different forms of Cs in soils. Moreover, Soil samples were analyzed for total Cs using two analytical methods i.e. destructive wet digestion technique (Atomic Absorption Spectrometry, AAS or by summation of all sequential extracted fractions, SUM) and non-destructive technique (Neutron Activation Analysis, NAA). The aim of this study was to evaluate soil total Cs-forms (especially, bio-available fraction) as affected by soil pollution. Cesium was mostly concentrated in the residual fraction, and its values ranged from 57.4% to 82.9 % of total Cs in sandy soils and from 31.5% to 64.5 % of total Cs in tested clayey soil. Then organically bound Cs- fraction followed by Cs-occluded in Fe-Mn fraction, carbonate, exchangeable and water soluble fractions. Results suggested that, Cs level is affected by soil organic matter content, Fe-Mn oxides and clay content. The mobile Cs fraction (the sum of soluble and exchangeable fractions) ranged from 2% up to 9.9 % of total Cs in sandy soils. However, a higher value (9.82% to 15.31 %) could be observed in case of the tested clayey soils. Soils D and E were more contaminated than other tested soils. Data show obviously, that soil contaminated due to the irrigation with either sewage effluent or industrial wastewater has resulted in a drastic increase in both metal-organic and occluded in Fe and Mn oxide fractions followed by the carbonate fraction

  6. Life Cycle Assessment of Two Vineyards after the Application of Precision Viticulture Techniques: A Case Study

    Directory of Open Access Journals (Sweden)

    Athanasios T. Balafoutis

    2017-11-01

    Full Text Available Precision viticulture is the application of site-specific techniques to vineyard production to improve grape quality and yield and minimize the negative effects on the environment. While there are various studies on the inherent spatial and temporal variability of vineyards, the assessment of the environmental impact of variable rate applications has attracted limited attention. In this study, two vineyards planted with different grapevine cultivars (Sauvignon Blanc and Syrah were examined for four consecutive growing seasons (2013–2016. The first year, the two vineyards were only studied in terms of soil properties and crop characteristics, which resulted in the delineation of two distinct management zones for each field. For the following three years, variable rate nutrient application was applied to each management zone based on leaf canopy reflectance, where variable rate irrigation was based on soil moisture sensors, meteorological data, evapotranspiration calculation, and leaf canopy reflectance. Life cycle assessment was carried out to identify the effect of variable rate applications on vineyard agro-ecosystems. The results of variable rate nutrients and water application in the selected management zones as an average value of three growing seasons were compared to the conventional practice. It was found that the reduction of product carbon footprint (PCF of grapes in Sauvignon Blanc between the two periods was 25% in total. Fertilizer production and distribution (direct and application (indirect was the most important sector of greenhouse gas (GHG emissions reduction, accounting for 17.2%, and the within-farm energy use was the second ranked sector with 8.8% (crop residue management increase GHG emissions by 1.1%, while 0.1% GHG reduction is obtained by pesticide use. For the Syrah vineyard, where the production was less intensive, precision viticulture led to a PCF reduction of 28.3% compared to conventional production. Fertilizers

  7. [Effects of nitrogen and irrigation water application on yield, water and nitrogen utilization and soil nitrate nitrogen accumulation in summer cotton].

    Science.gov (United States)

    Si, Zhuan Yun; Gao, Yang; Shen, Xiao Jun; Liu, Hao; Gong, Xue Wen; Duan, Ai Wang

    2017-12-01

    A field experiment was carried out to study the effects of nitrogen and irrigation water application on growth, yield, and water and nitrogen use efficiency of summer cotton, and to develop the optimal water and nitrogen management model for suitable yield and less nitrogen loss in summer cotton field in the Huang-Huai region. Two experimental factors were arranged in a split plot design. The main plots were used for arranging nitrogen factor which consisted of five nitrogen fertilizer le-vels(0, 60, 120, 180, 240 kg·hm -2 , referred as N 0 , N 1 , N 2 , N 3 , N 4 ), and the subplots for irrigation factor which consisted of three irrigation quota levels (30, 22.5, 15 mm, referred as I 1 , I 2 , I 3 ). There were 15 treatments with three replications. Water was applied with drip irrigation system. Experimental results showed that both irrigation and nitrogen fertilization promoted cotton growth and yield obviously, but nitrogen fertilizer showed more important effects than irrigation and was the main factor of regulating growth and yield of summer cotton in the experimental region. With the increase of nitrogen fertilization rate and irrigation amount, the dry mater accumulation of reproductive organs, the above-ground biomass at the flowering-bolling stage and seed cotton yield increased gradually, reached peak values at nitrogen fertilization rate of 180 kg·hm -2 and decreased slowly with the nitrogen fertilization rate further increased. The maximum yield of 4016 kg·hm -2 was observed in the treatment of N 3 I 1 . Increasing nitrogen fertilizer amount would improve significantly total N absorption of shoots and N content of stem and leaf, but decrease nitrogen partial factor productivity. The maximum irrigation-water use efficiency of 5.40 kg·m -3 and field water use efficiency of 1.24 kg·m -3 were found in the treatments of N 3 I 3 and N 3 I 1 , respectively. With increasing nitrogen fertilization amount, soil NO 3 - -N content increased and the main soil

  8. [Progress in transgenic fish techniques and application].

    Science.gov (United States)

    Ye, Xing; Tian, Yuan-Yuan; Gao, Feng-Ying

    2011-05-01

    Transgenic technique provides a new way for fish breeding. Stable lines of growth hormone gene transfer carps, salmon and tilapia, as well as fluorescence protein gene transfer zebra fish and white cloud mountain minnow have been produced. The fast growth characteristic of GH gene transgenic fish will be of great importance to promote aquaculture production and economic efficiency. This paper summarized the progress in transgenic fish research and ecological assessments. Microinjection is still the most common used method, but often resulted in multi-site and multi-copies integration. Co-injection of transposon or meganuclease will greatly improve the efficiency of gene transfer and integration. "All fish" gene or "auto gene" should be considered to produce transgenic fish in order to eliminate misgiving on food safety and to benefit expression of the transferred gene. Environmental risk is the biggest obstacle for transgenic fish to be commercially applied. Data indicates that transgenic fish have inferior fitness compared with the traditional domestic fish. However, be-cause of the genotype-by-environment effects, it is difficult to extrapolate simple phenotypes to the complex ecological interactions that occur in nature based on the ecological consequences of the transgenic fish determined in the laboratory. It is critical to establish highly naturalized environments for acquiring reliable data that can be used to evaluate the environ-mental risk. Efficacious physical and biological containment strategies remain to be crucial approaches to ensure the safe application of transgenic fish technology.

  9. The laser principles and application techniques

    International Nuclear Information System (INIS)

    Maillet, H.

    1990-01-01

    In this book on laser applications chapter 4 is devoted to uranium isotopic separation and chapter 5 to laser inertial fusion, other topics include machining, medical applications, measurements, military applications, holography, reprography, telecommunications, compact discs, light shows and safety [fr

  10. Assessment of Suitable Areas for Home Gardens for Irrigation Potential, Water Availability, and Water-Lifting Technologies

    Directory of Open Access Journals (Sweden)

    Tewodros Assefa

    2018-04-01

    Full Text Available The study was conducted in Lake Tana Basin of Ethiopia to assess potentially irrigable areas for home gardens, water availability, and feasibility of water-lifting technologies. A GIS-based Multi-Criteria Evaluation (MCE technique was applied to access the potential of surface and groundwater sources for irrigation. The factors affecting irrigation practice were identified and feasibility of water-lifting technologies was evaluated. Pairwise method and expert’s opinion were used to assign weights for each factor. The result showed that about 345,000 ha and 135,000 ha of land were found suitable for irrigation from the surface and groundwater sources, respectively. The rivers could address about 1–1.2% of the irrigable land during dry season without water storage structure whereas groundwater could address about 2.2–2.4% of the irrigable land, both using conventional irrigation techniques. If the seven major dams within the basin were considered, surface water potential would be increased and satisfy about 21% of the irrigable land. If rainwater harvesting techniques were used, about 76% of the basin would be suitable for irrigation. The potential of surface and groundwater was evaluated with respect to water requirements of dominant crops in the region. On the other hand, rope pump and deep well piston hand pump were found with relatively the most (26% and the least (9% applicable low-cost water-lifting technologies in the basin.

  11. Nucleus management with irrigating vectis

    Directory of Open Access Journals (Sweden)

    Srinivasan Aravind

    2009-01-01

    Full Text Available The main objective in modern cataract surgery is to achieve a better unaided visual acuity with rapid post-surgical recovery and minimal surgery-related complications. Early visual rehabilitation and better unaided vision can be achieved only by reducing the incision size. In manual small incision cataract surgery (MSICS, incision is between 5.5 to 7 mm. Once the nucleus is prolapsed into the anterior chamber, it can be extracted through the tunnel. Nucleus extraction with an irrigating vectis is a very simple technique, which combines mechanical and hydrostatic forces to express out the nucleus. This technique is time-tested with good results and more than 95% of nuclei in MSICS are extracted in this way offering all the merits of phacoemulsification with the added benefits of having wider applicability, better safety, shorter learning curve and lower cost.

  12. Sensing technologies for precision irrigation

    CERN Document Server

    Ćulibrk, Dubravko; Minic, Vladan; Alonso Fernandez, Marta; Alvarez Osuna, Javier; Crnojevic, Vladimir

    2014-01-01

    This brief provides an overview of state-of-the-art sensing technologies relevant to the problem of precision irrigation, an emerging field within the domain of precision agriculture. Applications of wireless sensor networks, satellite data and geographic information systems in the domain are covered. This brief presents the basic concepts of the technologies and emphasizes the practical aspects that enable the implementation of intelligent irrigation systems. The authors target a broad audience interested in this theme and organize the content in five chapters, each concerned with a specific technology needed to address the problem of optimal crop irrigation. Professionals and researchers will find the text a thorough survey with practical applications.

  13. Scintigraphic assessment of colostomy irrigation.

    Science.gov (United States)

    Christensen, P.; Olsen, N.; Krogh, K.; Laurberg, S.

    2002-09-01

    OBJECTIVE: This study aims to evaluate colonic transport following colostomy irrigation with a new scintigraphic technique. MATERIALS AND METHODS: To label the bowel contents 19 patients (11 uncomplicated colostomy irrigation, 8 complicated colostomy irrigation) took 111In-labelled polystyrene pellets one and two days before investigation. 99mTc-DTPA was mixed with the irrigation fluid to assess its extent within the bowel. Scintigraphy was performed before and after a standardized washout procedure. The colon was divided into three segments 1: the caecum andascending colon; 2: the transverse colon; 3: the descending and sigmoid colon. Assuming ordered evacuation of the colon, the contribution of each colonic segment to the total evacuation was expressed as a percentage of the original segmental counts. These were added to reach a total defaecation score (range: 0-300). RESULTS: In uncomplicated colostomy irrigation, the median defaecation score was 235 (range: 145-289) corresponding to complete evacuation of the descending and transverse colon and 35% evacuation of the caecum/ascending colon. In complicated colostomy irrigation it was possible to distinguish specific emptying patterns. The retained irrigation fluid reached the caecum in all but one patient. CONCLUSION: Scintigraphy can be used to evaluate colonic emptying following colostomy irrigation.

  14. Effect of Superabsorbent Application under Different Irrigation Regimes on Photosynthetic Pigments in Cuminum cyminum and its Relation with Seed and Essential Oil Yield

    Directory of Open Access Journals (Sweden)

    A. Pirzad

    2016-02-01

    yield of cumin seeds, 2 m2 of each plot was harvested and immediately were dried in the shade and at a temperature of 25 ° C. Essential oil, 25 g of powdered seeds in a one-liter flask, was extracted (W/W by the Clevenger method (Hydro distillation for 3 hours. Results and Discussion: Analysis of variance showed the significant interaction between the superabsorbent polymer and irrigation on the amount of leaf chlorophyll a, chlorophyll b, total chlorophyll, seed yield, percentage and yield of essential oil. This implies a different physiological response of cumin plant in terms of adding different amounts of superabsorbent and irrigation. Means comparison indicated that the highest concentration of chlorophyll a (0.266 mg/l and total chlorophyll (0.518 mg/l were obtained from plants irrigated after 50 mm of evaporation without polymer application. The maximum (0.259 mg/l and minimum (0.028 mg/l leaf chlorophyll b belonged to irrigation after 200 mm of evaporation using 60 and 240 kg/ha polymer, respectively. The highest yield of seed (1226 kg/ha and essential oil (36.5 kg/ha were obtained from well-watered plants (irrigation after 50 mm of evaporation and 60 kg/ha of polymer. Increasing irrigation intervals from 50 to 200 (50, 100, 150 and 200 mm of evaporation, need 120, 180 and 120 kg/ha polymer correspondingly for production of optimal yield of cumin. Essential oil of cumin plants was gradually and significantly enhanced by increasing irrigation distance, up to 150 mm of evaporation from pan, (with this particlefollow down by severe stress. Like seed yield the lowest yield of essential oil (0.9 kg/ha belonged to plants irrigated after 50 mm of evaporation using 120 kg/ha superabsorbent (less than irrigation after 200 mm of evaporation. In general, in the case of well-watered plants, irrigation after 50 mm of evaporation with a small amount of superabsorbent (60 kg/ha produced maximum seed yield and oil. However, if there is no access to water and increasing

  15. Effect of timing of joint application of hydroquinone and dicyandiamide on nitrous oxide emission from irrigated lowland rice paddy field.

    Science.gov (United States)

    Li, Xianglan; Zhang, Guangbin; Xu, Hua; Cai, Zucong; Yagi, Kazuyuki

    2009-06-01

    A field experiment was conducted to study the effect of timing of joint application of urease inhibitor hydroquinone (HQ) and nitrification inhibitor dicyandiamide (DCD) on N(2)O emission from irrigated lowland rice paddy field. Four treatments including Treatment CK (the control with urea alone), HQ/DCD-1 (application of HQ and DCD together with fertilizer before transplanting), HQ/DCD-2 (HQ and DCD with fertilizer at tillering stage) and HQ/DCD-3 (HQ and DCD with fertilizer at panicle initiation stage) were designed and implemented separately during rice growth period. Seasonal peaks of N(2)O flux occurred during midseason drainage and significant negative correlation between N(2)O flux and water layer depth was observed (r=-0.69 to -0.75, P<0.01). Mean N(2)O flux was the highest in the control with urea alone, while joint addition of HQ and DCD with urea lowered mean N(2)O flux considerably (P<0.05). Total N(2)O emission during rice growth season in Treatment CK, HQ/DCD-1, HQ/DCD-2 and HQ/DCD-3 was 3.90, 2.98, 1.73 and 3.23kgN(2)O-N ha(-1), respectively. Application of HQ and DCD together with basal fertilizer, tillering fertilizer and panicle initiation fertilizer decreased the total N(2)O emission by 24%, 56% and 17%, respectively, while increased grain yield by 10%, 18% and 6%, respectively. Effect of application of inhibitors on N(2)O emission during the continuous period from incorporation of HQ and DCD to rice harvest was also studied, where results indicating that the highest inhibiting efficiency of inhibitors on N(2)O emission was recorded when HQ and DCD applied with fertilizer at tillering stage.

  16. Common bean growth, N uptake and seed production in sandy loam soil as affected by application of plant residues, nitrogen and irrigation level

    International Nuclear Information System (INIS)

    Abdallah, A.A.G.

    2002-01-01

    Field experiment was conducted at the experimental farm, Inshas, atomic energy authority, egypt. Common bean seeds e.v. Nebrasks were cultivated in sandy loan soil using drip irrigation system prepared for this purpose. Two water regimes, i.e., 100% (793.0 m 3 /fed.) and 65% (513.0 m 3 /fed.) of maximum available water were used in main plots. Where in sub plots two fertilizers types were applied i.e., soybean plant residues which contains N 15 labelled as an organic matter without any addition of any fertilizer and nitrogen as chemical fertilizer without using organic matter. The obtained results indicated that, application of plant residues was superior for total seed yield comparing to nitrogen fertilization treatments. This N source with irrigation level of 793.33 m 3 /fed. had a slight increase in total seed yield comparing with (513.0 m 3 /fed.). Irrigation level of 513.0 m 3 /fed. (65% MAW) as well as application of soybean plant residues showed the highest value of water use efficiency. The highest value of N seed percentage was obtained irrigation level with (513.0 m 3 /fed.). Soybean plant residues improved and increased seeds N content, and total seeds protein content. Both N chemical and irrigation level (65% Maw) recorded highest values with N 15 % atom excess. This result has been obtained at two growth stages and seed yield. The same trend of N 15 % atom excess reflected N utilized with both growth stages and seed yield

  17. 77 FR 27768 - Greybull Valley Irrigation District; Notice of Preliminary Permit Application Accepted for Filing...

    Science.gov (United States)

    2012-05-11

    ... be 10 gigawatt-hours. Applicant Contacts: Mr. Lee Allen, 989 Highway 20 West, P.O. Box 44, Emblem, Wyoming 82422; phone: (307) 762-3555. Mr. William Schlenker, 989 Highway 20 West, P.O. Box 44, Emblem...

  18. 77 FR 27769 - Greybull Valley Irrigation District; Notice of Preliminary Permit Application Accepted for Filing...

    Science.gov (United States)

    2012-05-11

    ...-hours. Applicant Contacts: Mr. Lee Allen, 989 Highway 20 West, P.O. Box 44, Emblem, Wyoming 82422; phone: (307) 762-3555. Mr. William Schlenker, 989 Highway 20 West, P.O. Box 44, Emblem, Wyoming 82422; phone...

  19. Artificial Intelligence Techniques: Applications for Courseware Development.

    Science.gov (United States)

    Dear, Brian L.

    1986-01-01

    Introduces some general concepts and techniques of artificial intelligence (natural language interfaces, expert systems, knowledge bases and knowledge representation, heuristics, user-interface metaphors, and object-based environments) and investigates ways these techniques might be applied to analysis, design, development, implementation, and…

  20. Infra-red thermography for detecting drought in agricultural crops and scheduling irrigation

    Directory of Open Access Journals (Sweden)

    Petrović Ivana

    2016-01-01

    Full Text Available The use of thermal imaging is a fast growing and potentially important tool in various fields of agriculture. The technology visually identified the rise of temperature in crop canopy which occurs as a result of drought and allows the precise scheduling of crop irrigation. The aim of presenting paper was to demonstrate the application of these techniques on potato plants and to point out on the necessity of irrigation for potato sustainable and economically justified production.

  1. Evaluation of the Increased Rates of Water Super Absorbent and Humic Acid Application under Deficit Irrigation Condition on Some Agroecological Characteristics of Zea Mays Using Response Surface Methodology

    Directory of Open Access Journals (Sweden)

    M Jahan

    2017-03-01

    Full Text Available Introduction Water super absorbents are water absorbing natural or synthetic polymers (they may contain over 99% water. They have been defined as polymeric materials which exhibit the ability of swelling in water and retaining a significant fraction (> 20% of water within their structure, without dissolving in water content. The applications of hydrogels are grown extensively. These materials do not have any harm to the environment. Development of using super absorbent hydrogels to reduce crises such as soil erosion, frequent droughts or providing food security requires knowledge of their behaviors and performances in the soil. Humic substances are a mixture of different organic compounds that extract from various sources such as soil, humus, peat, oxidized lignite and coal. They are different in molecular size and chemical structure. A little amount of humic acid increase soil fertility by improving the physical, chemical and biological characteristics of soil. Increase in agricultural production and productivity depends, to a large extent, on the availability of water. Hence, the importance of irrigation is however, the availability of irrigation facilities which is highly inadequate in Iran. Determining the optimal amount of irrigation water has always been a main goal of researchers. Among the problems of excessive irrigation can be pointed to leach the nutrients especially nitrogen from the soil, the pollution of groundwater and environment and reduce fertilizer use efficiency, especially water-soluble fertilizers. To determine the optimal irrigation water and fertilizer, the use of mathematical models is inevitable. One of the most common methods used to optimize these factors is the central composite design. A central composite design is an experimental design, useful in response surface methodology, for building a second order (quadratic model for the response variable without needing to use a complete three-level factorial experiment

  2. Systems and rates of aerial application of fungicides in irrigated rice

    Directory of Open Access Journals (Sweden)

    Tânia Bayer

    Full Text Available ABSTRACT The present research studied the performance of flat-fan and hollow-cone nozzles, with application rates of 20 and 30 L ha-1, and rotary disc atomizer with application rates of 10 and 15 L ha-1. The test was conducted with a fungicide spray tank composed of Azoxystrobin + Difenoconazole, in which the density and penetration of droplets into the canopy were evaluated using a water-sensitive paper and the distribution of the active ingredients in the plant was evaluated through the chromatographic analysis. Higher application rates resulted in higher droplet density in the upper stratum of plants. In all treatments, the penetration of the droplets was 26% into the middle stratum and 23% into the lower stratum, in relation to the top of the crop, resulting in an average 25% penetration of droplets into the leaf canopy. The active ingredients were distributed in greater quantity in the upper stratum of the plant. For the same weight, the upper part of the ‘Puitá Inta CL’ rice cultivar has a leaf area 6.4 times larger than the lower part. It was concluded that higher application rate leads to higher droplet density in the upper stratum of the leaf canopy and that all systems and application rates promoted similar penetration of droplets into the canopy.

  3. Teachers of Advertising Media Courses Describe Techniques, Show Computer Applications.

    Science.gov (United States)

    Lancaster, Kent M.; Martin, Thomas C.

    1989-01-01

    Reports on a survey of university advertising media teachers regarding textbooks and instructional aids used, teaching techniques, computer applications, student placement, instructor background, and faculty publishing. (SR)

  4. Application of Machine Learning Techniques in Aquaculture

    OpenAIRE

    Rahman, Akhlaqur; Tasnim, Sumaira

    2014-01-01

    In this paper we present applications of different machine learning algorithms in aquaculture. Machine learning algorithms learn models from historical data. In aquaculture historical data are obtained from farm practices, yields, and environmental data sources. Associations between these different variables can be obtained by applying machine learning algorithms to historical data. In this paper we present applications of different machine learning algorithms in aquaculture applications.

  5. Audit Techniques for Service Oriented Architecture Applications

    Directory of Open Access Journals (Sweden)

    Liviu Adrian COTFAS

    2010-01-01

    Full Text Available The Service Oriented Architecture (SOA approach enables the development of flexible distributed applications. Auditing such applications implies several specific challenges related to interoperability, performance and security. The service oriented architecture model is described and the advantages of this approach are analyzed. We also highlight several quality attributes and potential risks in SOA applications that an architect should be aware when designing a distributed system. Key risk factors are identified and a model for risk evaluation is introduced. The top reasons for auditing SOA applications are presented as well as the most important standards. The steps for a successful audit process are given and discussed.

  6. Application of Pesticide Phytoremediation in Irrigated Rice Fields System Using Eceng Gondok (Eichhornia crassipes) Plants

    Science.gov (United States)

    Febriani, Ika Kartika; Hadiyanto

    2018-02-01

    The problem of environmental pollution especially urban water pollution becomes major issue in Indonesia. The cause of water pollution is not only from industrial factory waste disposal but also other causes which become pollution factor. One cause of water pollution is the existence of agricultural activities with the use of the amount of pesticides that exceed the threshold. As regulated in Government Regulation No. 82/2001 on Water Quality Management and Water Pollution Control, it is necessary to manage water quality and control water pollution wisely by taking into account the interests of current and future generations as well as the ecological balance. To overcome the problem of water pollution due to agricultural activities, it is necessary to conduct research on phytoremediation technique by utilizing eceng gondok plant. It is excepted that using this phytoremediation technique can reduce the problem of water pollution due to the use of pesticides on agricultural activities.

  7. Application of Pesticide Phytoremediation in Irrigated Rice Fields System Using Eceng Gondok (Eichhornia crassipes Plants

    Directory of Open Access Journals (Sweden)

    Kartika Febriani Ika

    2018-01-01

    Full Text Available The problem of environmental pollution especially urban water pollution becomes major issue in Indonesia. The cause of water pollution is not only from industrial factory waste disposal but also other causes which become pollution factor. One cause of water pollution is the existence of agricultural activities with the use of the amount of pesticides that exceed the threshold. As regulated in Government Regulation No. 82/2001 on Water Quality Management and Water Pollution Control, it is necessary to manage water quality and control water pollution wisely by taking into account the interests of current and future generations as well as the ecological balance. To overcome the problem of water pollution due to agricultural activities, it is necessary to conduct research on phytoremediation technique by utilizing eceng gondok plant. It is excepted that using this phytoremediation technique can reduce the problem of water pollution due to the use of pesticides on agricultural activities.

  8. Les techniques traditionnelles de captage et de partage des eaux d'irrigation dans l'Oasis de Béni Ounif (Région de Béchar, Sud-Ouest, Algérie)

    OpenAIRE

    Cherif, Rezzoug

    2014-01-01

    Traditional techniques of capture and sharing of waters of the oasis of Béni Ounif. For centuries, the oasis dwellers of the Béni Ounif used techniques for acquisition of groundwater to meet the domestic needs of the population of Ksar and garden irrigation. The oasis dwellers were able to master the management of water through these processes. Despite a low annual rainfall, they were able to manage critical situations of prolonged droughts while protecting their envir...

  9. Crop model application to soybean irrigation management in the mid-south USA

    Science.gov (United States)

    Since mid 1990s, there have been a rapid development and application of crop growth models such as APEX (the Agricultural Policy/Environmental eXtender) and RZWQM2 (Root Zone Water Quality Model). Such process-oriented models have been designed to study the interactions of genetypes, weather, soil, ...

  10. Analytical steady-state solutions for water-limited cropping systems using saline irrigation water

    Science.gov (United States)

    Skaggs, T. H.; Anderson, R. G.; Corwin, D. L.; Suarez, D. L.

    2014-12-01

    Due to the diminishing availability of good quality water for irrigation, it is increasingly important that irrigation and salinity management tools be able to target submaximal crop yields and support the use of marginal quality waters. In this work, we present a steady-state irrigated systems modeling framework that accounts for reduced plant water uptake due to root zone salinity. Two explicit, closed-form analytical solutions for the root zone solute concentration profile are obtained, corresponding to two alternative functional forms of the uptake reduction function. The solutions express a general relationship between irrigation water salinity, irrigation rate, crop salt tolerance, crop transpiration, and (using standard approximations) crop yield. Example applications are illustrated, including the calculation of irrigation requirements for obtaining targeted submaximal yields, and the generation of crop-water production functions for varying irrigation waters, irrigation rates, and crops. Model predictions are shown to be mostly consistent with existing models and available experimental data. Yet the new solutions possess advantages over available alternatives, including: (i) the solutions were derived from a complete physical-mathematical description of the system, rather than based on an ad hoc formulation; (ii) the analytical solutions are explicit and can be evaluated without iterative techniques; (iii) the solutions permit consideration of two common functional forms of salinity induced reductions in crop water uptake, rather than being tied to one particular representation; and (iv) the utilized modeling framework is compatible with leading transient-state numerical models.

  11. Bathymetric techniques and Indian Ocean applications

    Digital Repository Service at National Institute of Oceanography (India)

    Chakraborty, B.; Fernandes, W.A.

    reefs on the seabed to large water reservoirs and palynology. The book consists of contributions from internationally-known scientists from India, Australia, Malaysia, Norway, Mexico, USA, Germany, and Brazil, and shows applications around the world...

  12. Moving objects management models, techniques and applications

    CERN Document Server

    Meng, Xiaofeng; Xu, Jiajie

    2014-01-01

    This book describes the topics of moving objects modeling and location tracking, indexing and querying, clustering, location uncertainty, traffic aware navigation and privacy issues as well as the application to intelligent transportation systems.

  13. Optical coherence tomography: Technique and applications

    DEFF Research Database (Denmark)

    Thomsen, Jakob Borup; Sander, Birgit; Mogensen, Mette

    2009-01-01

    Optical coherence tomography (OCT) is a noninvasive optical imaging modality providing real-time video rate images in two and three dimensions of biological tissues with micrometer resolution. OCT fills the gap between ultrasound and confocal microscopy, since it has a higher resolution than...... of retinal diseases. The potential of OCT in many other applications is currently being explored, such as in developmental biology, skin cancer diagnostics, vulnerable plaque detection in cardiology, esophageal diagnostics and a number of other applications within oncology....

  14. 48 CFR 9904.413-50 - Techniques for application.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 7 2010-10-01 2010-10-01 false Techniques for application... ACCOUNTING STANDARDS COST ACCOUNTING STANDARDS 9904.413-50 Techniques for application. (a) Assignment of... subject to this phase-in. (v) If a segment is closed due to a sale or other transfer of ownership to a...

  15. 48 CFR 9904.410-50 - Techniques for application.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 7 2010-10-01 2010-10-01 false Techniques for application... ACCOUNTING STANDARDS COST ACCOUNTING STANDARDS 9904.410-50 Techniques for application. (a) G&A expenses of a... practice was to use a cost of sales or sales base, that business unit may use the transition method set out...

  16. The laser principles and application techniques. 2. ed.

    International Nuclear Information System (INIS)

    Maillet, H.

    1986-01-01

    Specialists of each field gathered to give a complete overview of laser techniques possibilities. Operation principles, properties and the different kinds of lasers are detailed. Inertial fusion, isotope separation, medecine are part of the laser application fields presented, and application techniques in these fields are described [fr

  17. Expert System Techniques and Applications in AEC-Design

    DEFF Research Database (Denmark)

    Andersen, Tom

    This part of a book presents expert system techniques applicable to building design and construction, and it reports and evaluates on systems developed in thar domain.......This part of a book presents expert system techniques applicable to building design and construction, and it reports and evaluates on systems developed in thar domain....

  18. Big data for development : applications and techniques

    NARCIS (Netherlands)

    Ali, Anwaar; Qadir, Junaid; ur Rasool, Raihan; Sathiaseelan, Arjuna; Zwitter, Andrej; Crowcroft, Jon

    2016-01-01

    With the explosion of social media sites and proliferation of digital computing devices and Internet access, massive amounts of public data is being generated on a daily basis. Efficient techniques/algorithms to analyze this massive amount of data can provide near real-time information about

  19. Application of luminescence techniques in retrospective dosimetry

    DEFF Research Database (Denmark)

    Bøtter-Jensen, L.; Jungner, H.

    1999-01-01

    Luminescence signals measured from minerals within bricks or ceramic samples can provide information about the absorbed radiation dose. This feature has for several years been used in dating archaeological and geological samples and recently luminescence techniques have been intensively used far ...

  20. The influence of the microbial quality of wastewater, lettuce cultivars and enumeration technique when estimating the microbial contamination of wastewater-irrigated lettuce.

    Science.gov (United States)

    Makkaew, P; Miller, M; Cromar, N J; Fallowfield, H J

    2017-04-01

    This study investigated the volume of wastewater retained on the surface of three different varieties of lettuce, Iceberg, Cos, and Oak leaf, following submersion in wastewater of different microbial qualities (10, 10 2 , 10 3 , and 10 4 E. coli MPN/100 mL) as a surrogate method for estimation of contamination of spray-irrigated lettuce. Uniquely, Escherichia coli was enumerated, after submersion, on both the outer and inner leaves and in a composite sample of lettuce. E. coli were enumerated using two techniques. Firstly, from samples of leaves - the direct method. Secondly, using an indirect method, where the E. coli concentrations were estimated from the volume of wastewater retained by the lettuce and the E. coli concentration of the wastewater. The results showed that different varieties of lettuce retained significantly different volumes of wastewater (p 0.01) were detected between E. coli counts obtained from different parts of lettuce, nor between the direct and indirect enumeration methods. Statistically significant linear relationships were derived relating the E. coli concentration of the wastewater in which the lettuces were submerged to the subsequent E. coli count on each variety the lettuce.

  1. Multitracer techniques: applications in chemical and life sciences

    International Nuclear Information System (INIS)

    Nayak, Dalia

    2001-01-01

    The scope and approaches of the 'multitracer technique' have briefly been reviewed. The various aspects of the 'multitracer technique' include, the methods of accelerator production of 'multitracers' and their separation, the application of this technique in the study of adsorption of metal ions on solid surfaces and in the study of distribution of trace elements in plants and animals

  2. Using Concept Map Technique in Accounting Education: Uludag University Application

    OpenAIRE

    Ertan, Yasemin; Yücel, Elif; Saraç, Mehlika

    2014-01-01

    In recent years accounting applications become more complicated because of the growing markets and developing technology. Therefore the requirements of accounting education have increased and trying some new learning techniques have become necessary. Thus, this study was prepared to measure the contribution of concept map technique, used in accounting lessons, to the effect on students learning level. In the first part of the study, the concept map technique and its applications were explaine...

  3. Techniques for Finding Vulnerabilities in Web Applications

    OpenAIRE

    Mihai Sandulescu

    2014-01-01

    The current trend is to move everything on the Internet. Because a lot of companies store sensitive user information, security has become mandatory. Usually, software developers don’t follow some basic practices in order to secure their applications. This paper will present in the second chapter, the white-box, black-box and gray-box methods which can be used in order to test applications for possible vulnerabilities. It focuses on fuzz testing, which is a black-box testing method, presented ...

  4. Dynamic Binary Modification Tools, Techniques and Applications

    CERN Document Server

    Hazelwood, Kim

    2011-01-01

    Dynamic binary modification tools form a software layer between a running application and the underlying operating system, providing the powerful opportunity to inspect and potentially modify every user-level guest application instruction that executes. Toolkits built upon this technology have enabled computer architects to build powerful simulators and emulators for design-space exploration, compiler writers to analyze and debug the code generated by their compilers, software developers to fully explore the features, bottlenecks, and performance of their software, and even end-users to extend

  5. Application of nuclear techniques in food conservation

    International Nuclear Information System (INIS)

    Alvarado, A.; Arias., L.

    1990-01-01

    This book has the following objectives: 1) determine the possibilities of establishing an investigation project, and the application of food irradiation in Costa Rica. 2) Promote national legislation and regulations in the field of irradiated foods. 3) Coordinate with the Comision de Energia Atomica de Costa Rica, the promotion of the food irradiation technology, at the producer/industrial/institutional/consumer level. 10 refs

  6. Modeling irrigation behavior in groundwater systems

    Science.gov (United States)

    Foster, Timothy; Brozović, Nicholas; Butler, Adrian P.

    2014-08-01

    Integrated hydro-economic models have been widely applied to water management problems in regions of intensive groundwater-fed irrigation. However, policy interpretations may be limited as most existing models do not explicitly consider two important aspects of observed irrigation decision making, namely the limits on instantaneous irrigation rates imposed by well yield and the intraseasonal structure of irrigation planning. We develop a new modeling approach for determining irrigation demand that is based on observed farmer behavior and captures the impacts on production and water use of both well yield and climate. Through a case study of irrigated corn production in the Texas High Plains region of the United States we predict optimal irrigation strategies under variable levels of groundwater supply, and assess the limits of existing models for predicting land and groundwater use decisions by farmers. Our results show that irrigation behavior exhibits complex nonlinear responses to changes in groundwater availability. Declining well yields induce large reductions in the optimal size of irrigated area and irrigation use as constraints on instantaneous application rates limit the ability to maintain sufficient soil moisture to avoid negative impacts on crop yield. We demonstrate that this important behavioral response to limited groundwater availability is not captured by existing modeling approaches, which therefore may be unreliable predictors of irrigation demand, agricultural profitability, and resilience to climate change and aquifer depletion.

  7. Effects of Irrigation and Nitrogen Application Rates on Yield and Yield Components of Corn, Sesame and Sugar beet in Mashhad Climatic Condition

    Directory of Open Access Journals (Sweden)

    R Heydari Pour

    2015-07-01

    Full Text Available In many crops, incorrect management of nitrogen and water is one of the most important factors in the resources productivity such as water and nitrogen. In order to evaluate the effects of different nitrogen levels (zero, 50, 100 and 150 kg ha-1 and irrigation application rates (100, 75 and 50% of water requirement per species on corn, sesame and sugar beet, three separate experiments was conducted in Agricultural Research Station of Ferdowsi University of Mashhad, Iran, in 2009-2010 growing season. Three separate experiments were arranged by strip plots in randomized complete block design, with three replications. The results showed that effect of irrigation application rates on biological yield and grain number per ear and interaction effects of water × nitrogen on plant height, 100 grain weight and grain yield of corn was significant. With decreasing irrigation over 25 % water requirements, the highest grain yield (4.93 ton ha-1 in corn observed by applying nitrogen equal to 50 kg.ha-1. In addition, the highest maize yield (9.41 ton.ha-1 in mentioned was obtained by supplying 100 % water requirements. Effects of Irrigation levels on plant height and the interaction effects of water × nitrogen on 1000 grain weight in sesame was significant. Under no water stress, the highest grain yield (1.22 ton ha-1 in sesame was obtained with applying 50kg nitrogen per ha. With supplying 75% water requirements plus 50 kg nitrogen per hactar, maximum yield of sesame (820 kg ha-1 was obtained. Results of this study indicated that interaction between studied factors had insignificant effect on economic and biological yield in sugar beet. With supplying 25% water requirements plus 50 kg nitrogen per ha, maximum yield of sugar beet (58.37 ton ha-1 was achieved. It seems that suitable nitrogen management can be considered as approach in optimize the water consuming.

  8. Neutron Scattering in Biology Techniques and Applications

    CERN Document Server

    Fitter, Jörg; Katsaras, John

    2006-01-01

    The advent of new neutron facilities and the improvement of existing sources and instruments world wide supply the biological community with many new opportunities in the areas of structural biology and biological physics. The present volume offers a clear description of the various neutron-scattering techniques currently being used to answer biologically relevant questions. Their utility is illustrated through examples by some of the leading researchers in the field of neutron scattering. This volume will be a reference for researchers and a step-by-step guide for young scientists entering the field and the advanced graduate student.

  9. Inverse Raman effect: applications and detection techniques

    International Nuclear Information System (INIS)

    Hughes, L.J. Jr.

    1980-08-01

    The processes underlying the inverse Raman effect are qualitatively described by comparing it to the more familiar phenomena of conventional and stimulated Raman scattering. An experession is derived for the inverse Raman absorption coefficient, and its relationship to the stimulated Raman gain is obtained. The power requirements of the two fields are examined qualitatively and quantitatively. The assumption that the inverse Raman absorption coefficient is constant over the interaction length is examined. Advantages of the technique are discussed and a brief survey of reported studies is presented

  10. Inverse Raman effect: applications and detection techniques

    Energy Technology Data Exchange (ETDEWEB)

    Hughes, L.J. Jr.

    1980-08-01

    The processes underlying the inverse Raman effect are qualitatively described by comparing it to the more familiar phenomena of conventional and stimulated Raman scattering. An experession is derived for the inverse Raman absorption coefficient, and its relationship to the stimulated Raman gain is obtained. The power requirements of the two fields are examined qualitatively and quantitatively. The assumption that the inverse Raman absorption coefficient is constant over the interaction length is examined. Advantages of the technique are discussed and a brief survey of reported studies is presented.

  11. Oncologic applications of diagnostic imaging techniques

    International Nuclear Information System (INIS)

    Forrest, L.J.; Thrall, D.E.

    1995-01-01

    Before appropriate therapy can be instituted for a cancer patient, the presence and extent of tumor must be evaluated. Deciding which imaging technique to use depends on tumor location, type, and biologic behavior. Conventional radiography provides important information at a relatively low cost compared with other imaging modalities. Ultrasound is a valuable adjunct to radiography, but does not replace it because both imaging modalities provide unique information. Nuclear medicine procedures contribute additional, unique data by providing physiological information, but specificity is lacking. Both CT and MRI provide images with exquisite anatomic detail, but availability and cost prohibit their general use

  12. Effect of irrigation, nitrogen application, and a nitrification inhibitor on nitrous oxide, carbon dioxide and methane emissions from an olive (Olea europaea L.) orchard

    Energy Technology Data Exchange (ETDEWEB)

    Maris, S.C., E-mail: stefania@macs.udl.cat [University of Lleida, Environment and Soil Science Department, Av. Alcalde Rovira Roure 191, E-25198 Lleida (Spain); Teira-Esmatges, M.R. [University of Lleida, Environment and Soil Science Department, Av. Alcalde Rovira Roure 191, E-25198 Lleida (Spain); Arbonés, A.; Rufat, J. [Programa Ús Eficient de l’Aigua, Institut de Recerca i Tecnologia Agroalimentàries (IRTA), Parc Científic i Tecnològic Agroalimentari de Lleida (PCiTAL). Parc de Gardeny, Edifici Fruitcentre, E-2503 Lleida (Spain)

    2015-12-15

    Drip irrigation combined with nitrogen (N) fertigation is applied in order to save water and improve nutrient efficiency. Nitrification inhibitors reduce greenhouse gas emissions. A field study was conducted to compare the emissions of nitrous oxide (N{sub 2}O), carbon dioxide (CO{sub 2}) and methane (CH{sub 4}) associated with the application of N fertiliser through fertigation (0 and 50 kg N ha{sup −1}), and 50 kg N ha{sup −1} + nitrification inhibitor in a high tree density Arbequina olive orchard. Spanish Arbequina is the most suited variety for super intensive olive groves. This system allows reducing production costs and increases crop yield. Moreover its oil has excellent sensorial features. Subsurface drip irrigation markedly reduced N{sub 2}O and N{sub 2}O + N{sub 2} emissions compared with surface drip irrigation. Fertiliser application significantly increased N{sub 2}O + N{sub 2}, but not N{sub 2}O emissions. Denitrification was the main source of N{sub 2}O. The N{sub 2}O losses (calculated as emission factor) ranging from − 0.03 to 0.14% of the N applied, were lower than the IPCC (2007) values. The N{sub 2}O + N{sub 2} losses were the largest, equivalent to 1.80% of the N applied, from the 50 kg N ha{sup −1} + drip irrigation treatment which resulted in water filled pore space > 60% most of the time (high moisture). Nitrogen fertilisation significantly reduced CO{sub 2} emissions in 2011, but only for the subsurface drip irrigation strategies in 2012. The olive orchard acted as a net CH{sub 4} sink for all the treatments. Applying a nitrification inhibitor (DMPP), the cumulative N{sub 2}O and N{sub 2}O + N{sub 2} emissions were significantly reduced with respect to the control. The DMPP also inhibited CO{sub 2} emissions and significantly increased CH{sub 4} oxidation. Considering global warming potential, greenhouse gas intensity, cumulative N{sub 2}O emissions and oil production, it can be concluded that applying DMPP with 50 kg N ha{sup −1

  13. Applications of probabilistic techniques at NRC

    International Nuclear Information System (INIS)

    Thadani, A.; Rowsome, F.; Speis, T.

    1984-01-01

    The NRC is currently making extensive use of probabilistic safety assessment in the reactor regulation. Most of these applications have been introduced in the regulatory activities in the past few years. Plant Probabilistic Safety Studies are being utilized as a design tool for applications for standard designs and for assessment of plants located in regions of particularly high population density. There is considerable motivation for licenses to perform plant-specific probabilistic studies for many, if not all, of the existing operating nuclear power plants as a tool for prioritizing the implementation of the many outstanding licensing actions of these plants as well as recommending the elimination of a number of these issues which are judged to be insignificant in terms of their contribution to safety and risk. Risk assessment perspectives are being used in the priorization of generic safety issues, development of technical resolution of unresolved safety issues, assessing safety significance of proposed new regulatory requirements, assessment of safety significance of some of the occurrences at operating facilities and in environmental impact analyses of license applicants as required by the National Environmental Policy Act. (orig.)

  14. Application of activation techniques to biological analysis

    International Nuclear Information System (INIS)

    Bowen, H.J.M.

    1981-01-01

    Applications of activation analysis in the biological sciences are reviewed for the period of 1970 to 1979. The stages and characteristics of activation analysis are described, and its advantages and disadvantages enumerated. Most applications involve activation by thermal neutrons followed by either radiochemical or instrumental determination. Relatively little use has been made of activation by fast neutrons, photons, or charged particles. In vivo analyses are included, but those based on prompt gamma or x-ray emission are not. Major applications include studies of reference materials, and the elemental analysis of plants, marine biota, animal and human tissues, diets, and excreta. Relatively little use of it has been made in biochemistry, microbiology, and entomology, but it has become important in toxicology and environmental science. The elements most often determined are Ag, As, Au, Br, Ca, Cd, Cl, Co, Cr, Cs, Cu, Fe, Hg, I, K, Mn, Mo, Na, Rb, Sb, Sc, Se, and Zn, while few or no determinations of B, Be, Bi, Ga, Gd, Ge, H, In, Ir, Li, Nd, Os, Pd, Pr, Pt, Re, Rh, Ru, Te, Tl, or Y have been made in biological materials

  15. Application of Water Quality and Ecology Indices of Benthic Macroinvertebrate to Evaluate Water Quality of Tertiary Irrigation in Malang District

    Directory of Open Access Journals (Sweden)

    Desi Kartikasari

    2013-12-01

    Full Text Available This research aims to determine the water quality of tertiary irrigation in several subdistricts in Malang, namely Kepanjen, Karangploso, and Tumpang. The water quality depends on the water quality indices (National Sanitation Foundation’s-NSF Indices and O’Connor’s Indices based on variables TSS, TDS, pH, DO, and Nitrate concentrate and ecological indices of benthic macroinvertebrate (Diversity Indices Shannon-Wiener, Hilsenhof Biotic Indices-HBI, Average Score per Taxon-ASPT which is calculated by Biological Monitoring Working Party-BMWP, Ephemeroptera Indices, Plecoptera, Trichoptera-EPT. Observation of the physico-chemical water quality and benthic macroinvertebrate on May 2012 to April 2013. The sampling in each subdistrict was done at two selected stations in tertiary irrigation channel with three plot at each station. The data of physico-chemical quality of water were used to calculate the water quality indices, while the benthic macroinvertebrate data were used to calculate the ecological indices. The research findings showed that 27 taxa of benthic macroinvertebrates belong 10 classes were found in the three subdistrict. The pH, DO, Nitrate, TSS and TDS in six tertiary irrigation channels in Malang still met the water quality standards based on Government Regulation No. 82 of 2001 on Management of Water Quality and Water Pollution Control Class III. Based on NSF-WQI indices and O'Connor's Indices, water qualities in these irrigation channels were categorized into medium or moderate (yellow to good (green category. However, based on benthic macroinvertebrate communities which was used to determine the HBI, the water quality in the irrigation channels were categorized into the fair category (fairly significant organic pollution to fairly poor (significant organic pollution, while based on the value of ASPT, the water were categorized into probable moderate pollution to probable severe pollution. The irrigation water which was

  16. Application of exploration geochemistry techniques in agriculture

    International Nuclear Information System (INIS)

    Santos, G.P. Jr.; Fernandez, L.G.; Petrache, C.A.; Almoneda, R.V.; Rosales, C.M.

    1989-01-01

    Soil samples collected from Tarlac, Nueva Ecija, Pampanga, Bulacan, Laguna and Quezon provinces were analyzed for Zn, Mn, Cu, Fe, Co, Pb, and Ni using two analytical methods - Smith and Lynch (S and L) element extraction technique used in exploration geochemical survey and the International Rice Research Institute (IRRI) technique for determining zinc availability in soil. The analytical results were treated statistically using the method of Lepeltier to obtain the background values. The background, or average concentrations of the elements obtained by the S and L method were an order-higher than those computed for the IRRI method. The different metal value contour maps of northwestern Luzon were multiplied by its corresponding metal ratio, IRRI/S and L to produce the agri-geochemical maps or agri-maps that show approximate trace element levels available to the plant. The agri-maps of northwestern Luzon show a region wide deficiency in Cu, Zn, Mn, Pb, Co, and Ni, with the exception of Baguio Area. It has been recognized that excess deficiency in certain minor or trace elements in, particularly the essential micronutrient elements, is one of the important factors in agricultural productivity. It is therefore, recommended that in order to assure the necessary level of trace elements in northwestern Luzon, additions of at least copper, zinc and manganese be provided together with the needed fertilizer. (Author). 14 figs.; 14 refs.; 4 tabs

  17. Atoms for Food and Nutrition: Application of Nuclear Techniques in Food and Agriculture

    International Nuclear Information System (INIS)

    Esilaba, A.O.

    2017-01-01

    KALRO is a corporate body created under the Kenya Agricultural and Livestock Research Act of 2013 to establish suitable legal and institutional frameworks for coordination of agricultural research in Kenya. It promote, streamline, co-ordinate and regulate research in crops, livestock, genetic resources and biotechnology and animal diseases. To expedite equitable access to research information, resources and technologies and promote the application of research findings and developed technologies in the field of agriculture and livestock. FAO's report identifies 15 trends and 10 challenges affecting the world's food systems. There are 10 key challenges that need to be addressed if we are to succeed in eradicating hunger and poverty, while making agriculture and food systems sustainable (FAO, 2017). Empowering small-scale farmers and providing them better access to information, markets and technologies is key to ensuring future food security. The mission of the Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture is to support and promote the safe and appropriate use of nuclear and related technologies by the FAO/IAEA member states in food and agriculture, with the aim to contribute to peace, health and prosperity throughout the world, especially to global food security and sustainable agricultural development.Isotopic techniques are employed to monitor foods for contamination with agrochemicals -optimizing sample preparation by radioisotopes -detecting contaminant by electron capture detector. Both stable and radioactive isotopes can be used as tracers in soil and water management & crop nutrition. Through collaboration with IAEA, KALRO is now the center in Africa where new drip irrigation technologies are being evaluated. KALRO partners with IAEA to host fellowship training for scientists and technicians from African region on soil and water management, efficient irrigation technologies and nitrogen fertilizer use efficiency. There is need for

  18. Applications of observational techniques in pavement engineering

    CSIR Research Space (South Africa)

    Steyn, WJVDM

    2007-05-01

    Full Text Available available at CSIR BE. The technology used to obtain the images at each of the resolutions and wavelengths, as well as the benefits and limitations and typical applications of the groups of images are as follows: 3.1 Visible waveband, Mm resolution... of technology enabled an increase in the scope of potential observations that is spreading towards the larger and smaller realms of visibility. In this sense observations can be made on a scale from very large artefacts (such as the earth) to very small...

  19. Real analysis modern techniques and their applications

    CERN Document Server

    Folland, Gerald B

    1999-01-01

    An in-depth look at real analysis and its applications-now expanded and revised.This new edition of the widely used analysis book continues to cover real analysis in greater detail and at a more advanced level than most books on the subject. Encompassing several subjects that underlie much of modern analysis, the book focuses on measure and integration theory, point set topology, and the basics of functional analysis. It illustrates the use of the general theories and introduces readers to other branches of analysis such as Fourier analysis, distribution theory, and probability theory.This edi

  20. Microbiological studies to select compatible rhizobia for application in wastelands using molecular and nuclear techniques

    International Nuclear Information System (INIS)

    Abdel Raouf, A.M.N

    2010-01-01

    The present work aimed at utilization of wastelands and improving their fertility status through the following topics:1- Isolation and identification of rhizobia from wastelands, then selecting the most resistant isolate to saline conditions.2- Studying the effect of radiation on the most salt tolerant rhizobia and marketing rhizobia using molecular and microbiological techniques.3- Identification and culturing of selected compatible rhizobia to be used in application experiments as a bio fertilizer to inoculate the leguminous crops in order to improve the efficiency of the Rhizobium-legume symbiosis and reclamation of wastelands.4- Application of molecular and nuclear techniques such 16S ribosomal RNA and studying the sequence for these strains for comparison between the most potent rhizobia.5- Determination of protein profile for the most potent rhizobia to throw light about similarities between these strains.6- Attempts to apply polymerase chain reaction (PCR) and use primers for differentiation between the most potent rhizobia.7- Experimental fields for growing some leguminous plants inoculated with irradiated and non-irradiated rhizobia and irrigated with different concentrations of sea water and their effects on growth and total N content of plants.

  1. Application of tracer technique in cement industry

    International Nuclear Information System (INIS)

    Baran'ai, L.

    1979-01-01

    Application is stated of the radioisotope indication method in the cement industry. The method was applied in three directions. In the first direction, by means of labelling of 300 steel mill balls by cobalt-60, wear of them was examined. The degree of wear of milling balls in the process of milling was determined according to the decrease of their weight. Radioactive label served only for tracing controll balls. In the second direction, according to the natural radioactivity being presented in ashes by radioisotopes radium-226 and thorium-229, amount of ashes in the products of cement milling was determined (in the mill product, cement product, flying dust and back loading groats). In the third direction, by means of labelling of definite fractions of mille by radioisotope gold-198, optimization of technological parameters of silos were raw meal is homogenization. The following technological parameters have been established: amount of homogenized material; time of homogenization and frequency of intensity changing of supplied compressed air jet [ru

  2. Application of on-line analytical processing technique in accelerator

    International Nuclear Information System (INIS)

    Xie Dong; Li Weimin; He Duohui; Liu Gongfa; Xuan Ke

    2005-01-01

    A method of application of the on-line analytical processing technique in accelerator is described, which includes data pre-processing, the process of constructing of data warehouse and on-line analytical processing. (authors)

  3. Portable flash X-ray systems: applications and techniques

    International Nuclear Information System (INIS)

    Bryant, L.E.

    1976-01-01

    Three portable flash x-ray equipments are described, and applications such as jet and high explosive studies, bullet impact and lead casting experiments are given as well as techniques for triggering and protection of equipment and film

  4. Dosimetry techniques for applications of incorporated radionuclides

    International Nuclear Information System (INIS)

    Howell, R.W.; Rao, D.V.; Haydock, C.

    1989-01-01

    Beta particle emitters are attracting attention as the radiolabels of choice for therapeutic radiopharmaceutical. Their use in cancer therapy has drawn attention to a variety of problems in estimating the absorbed dose to primary tumors and metastases from incorporated Β-emitters. Experimental evidence indicates that the distribution of radiopharmaceutical, such as radiolabeled monoclonal antibodies, is highly nonuniform in tumor tissue. Three levels of nonuniformity may be noted: (1) inhomogeneity at the macroscopic level due to poor penetration of the radiopharmaceutical into the tumor, (2) microscopic inhomogeneity due to large variations in the number of binding sites on the tumor cells, and (3) nonuniformity at the subcellular level. Conventional application of the MIRD Schema for calculating absorbed doses from incorporated radionuclides may be inadequate under these circumstances since this approach assumes that the, distribution of radioactivity in the organ is uniform. The conventional dosimetry may be modified to handle inhomogeneous activity distributions by dividing the tumor into a number of subregions. At the macroscopic level a spherical tumor may be broken up into a group of concentric annular regions of tissue. At the microscopic level the tumor or metastasis may be considered as a multicellular cluster which in essence divides the tumor into many subtumors of cellular dimensions. Finally, at the subcellular level, a cancer cell may be viewed as consisting of several compartments: the cell membrane, cytoplasm, and nucleus. In each case absorbed fractions, and therefore the total absorbed doses, may be calculated for the various subregions of the tumor using standard MIRD procedures. Using macroscopic and multicellular dosimetry models, the relative importance of these various levels of inhomogeneity in radionuclide distribution is examined. A dosimetry model which accounts for the possible time dependence of the tumor mass is formulated

  5. Irrigation and Autocracy

    DEFF Research Database (Denmark)

    Bentzen, Jeanet Sinding; Kaarsen, Nicolai; Wingender, Asger Moll

    We show that societies with a history of irrigation-based agriculture have been less likely to adopt democracy than societies with a history of rainfed agriculture. Rather than actual irrigation, the empirical analysis is based on how much irrigation potentially can increase yields.Irrigation pot...

  6. Technical efficiency of irrigated vegetable production among ...

    African Journals Online (AJOL)

    This study was carried out to analyse the technical efficiency of irrigated vegetable production among smallholder farmers in the guinea savannah, Nigeria, and determine the cost and returns on irrigated vegetable production. Two-stage sampling technique was used, purposive selection of two states and three Local ...

  7. The application of different techniques to determine activated sludge ...

    African Journals Online (AJOL)

    The application of different techniques to determine activated sludge kinetic parameters in a food industry wastewater. ... method) and a respirometric technique based on oxygen consumption measurements, were used to compare microbial parameters using a wastewater model system of a potato processing plant.

  8. Radioanalytical techniques and their application in forensic science

    International Nuclear Information System (INIS)

    Chattopadhyay, N.

    1998-01-01

    Neutron techniques mainly in the form of Neutron Activation Analysis (NAA) is suitable for determination of very low amounts of many elements and can be effectively applied in crime investigation. Trace element analysis plays a significant role in forensic science. Different aspects of radioanalytical techniques, role of a few typical elements and their forensic application in different types of samples are discussed

  9. Intelligent techniques in engineering management theory and applications

    CERN Document Server

    Onar, Sezi

    2015-01-01

    This book presents recently developed intelligent techniques with applications and theory in the area of engineering management. The involved applications of intelligent techniques such as neural networks, fuzzy sets, Tabu search, genetic algorithms, etc. will be useful for engineering managers, postgraduate students, researchers, and lecturers. The book has been written considering the contents of a classical engineering management book but intelligent techniques are used for handling the engineering management problem areas. This comprehensive characteristics of the book makes it an excellent reference for the solution of complex problems of engineering management. The authors of the chapters are well-known researchers with their previous works in the area of engineering management.

  10. Contrast-enhanced Spectral Mammography: Technique, Indications, and Clinical Applications.

    Science.gov (United States)

    Bhimani, Chandni; Matta, Danielle; Roth, Robyn G; Liao, Lydia; Tinney, Elizabeth; Brill, Kristin; Germaine, Pauline

    2017-01-01

    Contrast-enhanced spectral mammography (CESM) combines the benefits of full field digital mammography with the concept of tumor angiogenesis. Technique and practical applications of CESM are discussed. An overview of the technique is followed by a demonstration of practical applications of CESM in our practice. We have successfully implemented CESM into our practice as a screening, diagnostic, staging, and treatment response tool. It is important to understand the technique of CESM and how to incorporate it into practice. Copyright © 2017 The Association of University Radiologists. Published by Elsevier Inc. All rights reserved.

  11. Application of functional analysis techniques to supervisory systems

    International Nuclear Information System (INIS)

    Lambert, Manuel; Riera, Bernard; Martel, Gregory

    1999-01-01

    The aim of this paper is to apply firstly two interesting functional analysis techniques for the design of supervisory systems for complex processes, and secondly to discuss the strength and the weaknesses of each of them. Two functional analysis techniques have been applied, SADT (Structured Analysis and Design Technique) and FAST (Functional Analysis System Technique) on a process, an example of a Water Supply Process Control (WSPC) system. These techniques allow a functional description of industrial processes. The paper briefly discusses the functions of a supervisory system and some advantages of the application of functional analysis for the design of a 'human' centered supervisory system. Then the basic principles of the two techniques applied on the WSPC system are presented. Finally, the different results obtained from the two techniques are discussed

  12. Review on Micro- and Nanolithography Techniques and Their Applications

    Directory of Open Access Journals (Sweden)

    Werayut Srituravanich

    2012-01-01

    Full Text Available This article reviews major micro- and nanolithography techniques and their applications from commercial micro devices to emerging applications in nanoscale science and engineering. Micro- and nanolithography has been the key technology in manufacturing of integrated circuits and microchips in the semiconductor industry. Such a technology is also sparking a magnificent transformation of nanotechnology. The lithography techniques including photolithography, electron beam lithography, focused ion beam lithography, soft lithography, nanoimprint lithography and scanning probe lithography are discussed. Furthermore, their applications are reviewed and summarized into four major areas: electronics and microsystems, medical and biotech, optics and photonics, and environment and energy harvesting.

  13. Application of radioactive techniques in the petrochemical plant

    International Nuclear Information System (INIS)

    Wei Weisheng; Wang Guorong; Yan Xiangfu

    2006-01-01

    Gamma scanning and neutron backscatter techniques, which are widely used in petrochemical plants, are briefly introduced. The fundamental is explained and the major applications in the petrochemical plants are given. Emphasis is placed on the industrial application of gamma scanning in tower operation and the neutron backscatter in the level detection of an industrial gas/liquid separator and a hydrogenation reactor. The application results show that radioactive techniques can play a key role in trouble shooting, optimization and predictive maintenance of the petrochemical devices. (authors)

  14. Application of CFD technique for HYFLEX aerodynamic design

    OpenAIRE

    Yamamoto, Yukimitsu; Watanabe, Shigeya; Ishiguro, Mitsuo; Ogasawara, Ko; 山本 行光; 渡辺 重哉; 石黒 満津夫; 小笠原 宏

    1994-01-01

    An overview of the application of Computational Fluid Dynamics (CFD) technique for the HYFLEX (Hypersonic Flight Experiment) aerodynamic design by using the numerical simulation codes in the supersonic and hypersonic speed ranges is presented. Roles of CFD required to make up for the short term of development and small amount of the wind tunnel test cases, application in the HYFLEX aerodynamic design and their application methods are described. The procedure of CFD code validation by the expe...

  15. The Effect of Irrigation Cut-off in Flowering Stage and Foliar Application of Spermidine on Essential Oil Quantity and Quality of Three Ecotypes of Cumin

    Directory of Open Access Journals (Sweden)

    Sarah Bakhtari

    2017-08-01

    Full Text Available Introduction Cumin (Cuminum cyminum L. is an annual plant that commonly cultivated in arid and semiarid regions of Iran. The crop has a wide range of uses including medicinal, cosmetic and food industry. Cumin occupies about 26% of total area devoted to medicinal plants in Iran. However, cumin is seriously affected by the Fusarium wilt and blight diseases. The diseases usually increase under warm and wet conditions. Control of the diseases incidence is a crucial factor for cumin production. Limited control of the diseases is provided by seed pre-sowing with certain fungicides such as benlate. Soil fumigation with methyle bromide can provide a control measure against the disease but may be limited application value for large scale production systems in the open field. In addition, methyle bromide is considered an ozone-depleting compound and has potential risk on the living environment and human health. Considering the environmental limitations of chemical fungicides, it seems appropriate to search for a supplemental control strategy .It was demonstrated that peak of the diseases incidence is occurred at flowering stage and irrigation cut-off in this time may be reduced the diseases density. Materials and methods This experiment was conducted in a split-split-plot arrangement in randomized complete block design with three replications in research farm of Shahid Bahonar University of Kerman at 2014. The experimental treatments were irrigation (complete irrigation and cut-off the irrigation in flowering stage assigned to main plots, foliar application of spermidine (0, 1 and 2 Mm as subplot and cumin ecotypes (Kerman, Khorasan and Esfahan that was randomized in sub-subplot. The seedbed preparation was made based on common practices at the location. Plots size under the trial was 4 m×3 m so as to get 50 cm inter row spacing in six rows. The ideal density of the crops was considered as 120 plant.m-2. As soon as the seeds were sown, irrigation

  16. Irrigation scheduling with the neutron probe

    International Nuclear Information System (INIS)

    Travers, P.

    1987-01-01

    The operational theory of the neutron probe is briefly outlined and its application and uses discussed in relation to determination of soil compaction and irrigation scheduling. Graphic examples are given of alluvial soil moisture profiles and how this information can be used to improve trickle irrigation in vineyards. 3 refs., 7 figs

  17. The Effect of Irrigation Regimes and Mulch Application on Vegetative Indices and Essential Oil Content of Peppermint (Mentha piperita L.

    Directory of Open Access Journals (Sweden)

    M. Azizi

    2016-02-01

    Full Text Available Peppermint (Mentha piperita L. from Lamiaceae family is one of the most important medicinal plants, used in food, sanitary and cosmetic industries. A field experiment was carried out in Ferdowsi University of Mashhad in 2010-2011 to evaluate the effects of three irrigation levels (100, 80 and 60 percent of water requirements calculated by evaporation pan class A and two mulch types (black plastic and wood chips in comparison to control (without mulch on physiological parameter and essential oils content in a factorial experiments on the basis of Randimised Complete Block Desing with four replications. The data obtained from each harvest analyzed as a factorial experiment on the basis of randomized complete block design with four replications and the results of two harvests analyzed as split plot on time. The results of two harvest indicated that peppermint plants grow better in the first harvest than the second harvest. Plants collected in the first harvest showed higher dry matter and essential oil yield. The highest dry herb yield (44.12 g/plant, the highest percentage of essential oil (2.835 %v/w and the highest essential oil yield (116.7 l/ha detected in plots treated with third level of irrigation and use of wood chips mulch. In conclusion the results also confirmed that the highest dry herb and the highest oil yield per area unit were observed in plots treated with third level of irrigation with use of wood chips mulch.

  18. Thermal analysis of different application techniques on Nd:YAG laser after root canal preparation of single-rooted teeth

    International Nuclear Information System (INIS)

    Archilla, Jose Ricardo de F.

    2001-01-01

    The experiment objective is to analyze temperature variation, by means of three different application techniques of Nd:YAG laser in the root canals of singlerooted anterior teeth. Three root canals were instrumented, irrigated, X-rayed to measure the remaining dentin in the apical area and submitted to laser irradiation techniques used by Gutknecht, Matsumoto and a new technique with oscillatory movement. The used laser parameters were: pulse energy 250 mJ, frequency 5 Hz, pulse fluency 354 J/cm 2 , average potency 1,25 W, pulse width 300 μs, fiber core diameter 300 μs and interval of thermal relaxation of 20 s. After temperature evaluation and interpretation of the obtained data, it was concluded: 1) the oscillatory technique provided a better heat distribution during the laser application, when analyzing the graphs separately; 2) all the used techniques are within a pattern of safety, analyzing the average and highest temperatures of the apical area and the middle third, even so, disrespecting the last application day and the middle third of root 'C'.(author)

  19. Estimation of net groundwater use in irrigated river basins using geo-information techniques : a case study in Rechna Doab, Pakistan

    NARCIS (Netherlands)

    Ahmad, M.D.

    2002-01-01

    Keywords: remote sensing, GIS, water balance, groundwater, net groundwater use, recharge, water management, Rechna Doab, Pakistan.

    Over-exploitation of groundwater resources threatens the future of irrigated agriculture, especially in the arid and semi-arid regions of the world. In

  20. Les techniques traditionnelles de captage et de partage des eaux d'irrigation dans l'Oasis de Béni Ounif (Région de Béchar, Sud-Ouest, Algérie

    Directory of Open Access Journals (Sweden)

    REZZOUG CHERIF

    2014-08-01

    Full Text Available Traditional techniques of capture and sharing of waters of the oasis of Béni Ounif. For centuries, the oasis dwellers of the Béni Ounif used techniques for acquisition of groundwater to meet the domestic needs of the population of Ksar and garden irrigation. The oasis dwellers were able to master the management of water through these processes. Despite a low annual rainfall, they were able to manage critical situations of prolonged droughts while protecting their environment. These ancient techniques such as traditional wells including foggaras have proven effective in the past. However with the addition of modern methods of water catchment (boreholes and pumps, the ancestral techniques of irrigation degraded from one year to another and their future is threatened. The use of new systems of pumping of groundwater by drilling, and not taken into effective charge of Foggaras, made this system to lose its value which deteriorates while the palm groves disappear. The overpumping causes a significant decrease of the level of the groundwater. Soil salinization is widespread throughout the oasis and water pollution has even reached the whole tablecloth of the oasis. Over 80% of these systems have been abandoned in recent years. However, during the years 2007 and 2008, different rehabilitation projects have been launched by the concerned departments and even some oasis dwellers have started processes to maintain several foggaras, sources and seguias. This study aims to analyze the traditional techniques of capture and sharing of waters of the oasis of Béni Ounif.

  1. Active noise control technique and its application on ships

    Directory of Open Access Journals (Sweden)

    CHEN Kean

    2017-08-01

    Full Text Available Due to the rapid development during past three decades, Active Noise Control(ANC has become a highly complementary noise control approach in comparison with traditional approaches, and has formed a complete system including basic theory, investigation approach, key techniques and system implementation. Meanwhile, substantial progress has been achieved in such fields as the practical application, industrialization development and commercial popularization of ANC, and this developed technique provides a practical and feasible choice for the active control of ship noise. In this review paper, its sound field analysis, system setup and key techniques are summarized, typical examples of ANC-based engineering applications including control of cabin noise and duct noise are briefly described, and a variety of forefronts and problems associated with the applications of ANC in ship noise control, such as active sound absorption, active sound insulation and smart acoustic structure, are subsequently discussed.

  2. Instrumental analytical techniques in geochemistry: Requirements and applications

    International Nuclear Information System (INIS)

    Willis, J.P.

    1986-01-01

    Geochemists must analyse an extremely wide range of terrestrial and planetary materials. The instrumental techniques necessary to cope with this difficult task are considered. The most important analytical techniques in use by the geochemist today are AAS, ICP-OES, INAA, MSID and XRFS, and the electron microscope for in situ mineral analysis. Some applications of these techniques to solving major problems in geochemistry are discussed. The importance of certified reference materials and of high quality geochemical data are emphasized. It is concluded that the general quality of trace element data has improved over the past 25 years, as a direct result of the application of modern instrumental techniques. Surprisingly, the quality of data reported for certain major elements has deteriorated over that time, when compared with data obtainable by classical chemical methods. Predictions are made concerning the instrumentation needs of the next generation of geochemists. (orig.) [de

  3. Technical descriptions of ten irrigation technologies for conserving energy

    Energy Technology Data Exchange (ETDEWEB)

    Harrer, B.J.; Wilfert, G.L.

    1983-05-01

    Technical description of ten technologies which were researched to save energy in irrigated agriculture are presented. These technologies are: well design and development ground water supply system optimization, column and pump redesign, variable-speed pumping, pipe network optimization, reduced-pressure center-pivot systems, low-energy precision application, automated gated-pipe system, computerized irrigation scheduling, and instrumented irrigation scheduling. (MHR)

  4. Tracking antibiotic resistance genes in soil irrigated with dairy wastewater

    Science.gov (United States)

    In southern Idaho, the application of dairy wastewater to agricultural soils is a widely used practice to irrigate crops and recycle nutrients. In this study, small-scale field plots were irrigated monthly (6 times) with dairy wastewater (100%), wastewater diluted to 50% with irrigation (canal) wate...

  5. Emerging Raman Applications and Techniques in Biomedical and Pharmaceutical Fields

    CERN Document Server

    Morris, Michael D

    2010-01-01

    The book presents the latest technological advances in Raman spectroscopy that are presently redrawing the landscape of many fields of biomedical and pharmaceutical R&D. Numerous examples are given to illustrate the application of the new methods and compared with established and related techniques. The book is suitable for both new researchers and practitioners in this area as well as for those familiar with the Raman technique but seeking to keep abreast of the latest dramatic advances in this field.

  6. Application of artificial intelligence techniques to TRR operation

    International Nuclear Information System (INIS)

    Ho, L.; Tseng, C.; Chang, S.

    1986-01-01

    It has been over ten years since TRR had its initial critical. To collect the experiences of shift operators and technique staffs and transfer these experts' knowledge to a computer and build an expert system is a typical application of artificial intelligence techniques to nuclear business. The system can provide the correct information of TRR operation for shift personnel, new staffs and other technical people

  7. Application of the Delphi technique in healthcare maintenance.

    Science.gov (United States)

    Njuangang, Stanley; Liyanage, Champika; Akintoye, Akintola

    2017-10-09

    Purpose The purpose of this paper is to examine the research design, issues and considerations in the application of the Delphi technique to identify, refine and rate the critical success factors and performance measures in maintenance-associated infections. Design/methodology/approach In-depth literature review through the application of open and axial coding were applied to formulate the interview and research questions. These were used to conduct an exploratory case study of two healthcare maintenance managers, randomly selected from two National Health Service Foundation Trusts in England. The results of exploratory case study provided the rationale for the application of the Delphi technique in this research. The different processes in the application of the Delphi technique in healthcare research are examined thoroughly. Findings This research demonstrates the need to apply and integrate different research methods to enhance the validity of the Delphi technique. The rationale for the application of the Delphi technique in this research is because some healthcare maintenance managers lack knowledge about basic infection control (IC) principles to make hospitals safe for patient care. The result of first round of the Delphi exercise is a useful contribution in its own rights. It identified a number of salient issues and differences in the opinions of the Delphi participants, noticeably between healthcare maintenance managers and members of the infection control team. It also resulted in useful suggestions and comments to improve the quality and presentation of the second- and third-round Delphi instruments. Practical implications This research provides a research methodology that can be adopted by researchers investigating new and emerging issues in the healthcare sector. As this research demonstrates, the Delphi technique is relevant in soliciting expert knowledge and opinion to identify performance measures to control maintenance-associated infections in

  8. Review and classification of variability analysis techniques with clinical applications.

    Science.gov (United States)

    Bravi, Andrea; Longtin, André; Seely, Andrew J E

    2011-10-10

    Analysis of patterns of variation of time-series, termed variability analysis, represents a rapidly evolving discipline with increasing applications in different fields of science. In medicine and in particular critical care, efforts have focussed on evaluating the clinical utility of variability. However, the growth and complexity of techniques applicable to this field have made interpretation and understanding of variability more challenging. Our objective is to provide an updated review of variability analysis techniques suitable for clinical applications. We review more than 70 variability techniques, providing for each technique a brief description of the underlying theory and assumptions, together with a summary of clinical applications. We propose a revised classification for the domains of variability techniques, which include statistical, geometric, energetic, informational, and invariant. We discuss the process of calculation, often necessitating a mathematical transform of the time-series. Our aims are to summarize a broad literature, promote a shared vocabulary that would improve the exchange of ideas, and the analyses of the results between different studies. We conclude with challenges for the evolving science of variability analysis.

  9. Review and classification of variability analysis techniques with clinical applications

    Science.gov (United States)

    2011-01-01

    Analysis of patterns of variation of time-series, termed variability analysis, represents a rapidly evolving discipline with increasing applications in different fields of science. In medicine and in particular critical care, efforts have focussed on evaluating the clinical utility of variability. However, the growth and complexity of techniques applicable to this field have made interpretation and understanding of variability more challenging. Our objective is to provide an updated review of variability analysis techniques suitable for clinical applications. We review more than 70 variability techniques, providing for each technique a brief description of the underlying theory and assumptions, together with a summary of clinical applications. We propose a revised classification for the domains of variability techniques, which include statistical, geometric, energetic, informational, and invariant. We discuss the process of calculation, often necessitating a mathematical transform of the time-series. Our aims are to summarize a broad literature, promote a shared vocabulary that would improve the exchange of ideas, and the analyses of the results between different studies. We conclude with challenges for the evolving science of variability analysis. PMID:21985357

  10. [Cardiac computed tomography: new applications of an evolving technique].

    Science.gov (United States)

    Martín, María; Corros, Cecilia; Calvo, Juan; Mesa, Alicia; García-Campos, Ana; Rodríguez, María Luisa; Barreiro, Manuel; Rozado, José; Colunga, Santiago; de la Hera, Jesús M; Morís, César; Luyando, Luis H

    2015-01-01

    During the last years we have witnessed an increasing development of imaging techniques applied in Cardiology. Among them, cardiac computed tomography is an emerging and evolving technique. With the current possibility of very low radiation studies, the applications have expanded and go further coronariography In the present article we review the technical developments of cardiac computed tomography and its new applications. Copyright © 2014 Instituto Nacional de Cardiología Ignacio Chávez. Published by Masson Doyma México S.A. All rights reserved.

  11. Knowledge based systems advanced concepts, techniques and applications

    CERN Document Server

    1997-01-01

    The field of knowledge-based systems (KBS) has expanded enormously during the last years, and many important techniques and tools are currently available. Applications of KBS range from medicine to engineering and aerospace.This book provides a selected set of state-of-the-art contributions that present advanced techniques, tools and applications. These contributions have been prepared by a group of eminent researchers and professionals in the field.The theoretical topics covered include: knowledge acquisition, machine learning, genetic algorithms, knowledge management and processing under unc

  12. 9th International Conference on Optimization : Techniques and Applications

    CERN Document Server

    Wang, Song; Wu, Soon-Yi

    2015-01-01

    This book presents the latest research findings and state-of-the-art solutions on optimization techniques and provides new research direction and developments. Both the theoretical and practical aspects of the book will be much beneficial to experts and students in optimization and operation research community. It selects high quality papers from The International Conference on Optimization: Techniques and Applications (ICOTA2013). The conference is an official conference series of POP (The Pacific Optimization Research Activity Group; there are over 500 active members). These state-of-the-art works in this book authored by recognized experts will make contributions to the development of optimization with its applications.

  13. Privacy-aware knowledge discovery novel applications and new techniques

    CERN Document Server

    Bonchi, Francesco

    2010-01-01

    Covering research at the frontier of this field, Privacy-Aware Knowledge Discovery: Novel Applications and New Techniques presents state-of-the-art privacy-preserving data mining techniques for application domains, such as medicine and social networks, that face the increasing heterogeneity and complexity of new forms of data. Renowned authorities from prominent organizations not only cover well-established results-they also explore complex domains where privacy issues are generally clear and well defined, but the solutions are still preliminary and in continuous development. Divided into seve

  14. Novel application of vacuum sealing drainage with continuous irrigation of potassium permanganate for managing infective wounds of gas gangrene.

    Science.gov (United States)

    Hu, Ning; Wu, Xing-Huo; Liu, Rong; Yang, Shu-Hua; Huang, Wei; Jiang, Dian-Ming; Wu, Qiang; Xia, Tian; Shao, Zeng-Wu; Ye, Zhe-Wei

    2015-08-01

    Traumatic gas gangrene is a fatal infection mainly caused by Clostridium perfringens. It is a challenge to manage gas gangrene in open wounds and control infection after debridement or amputation. The aim of the present study was to use vacuum sealing drainage (VSD) with continuous irrigation of potassium permanganate to manage infective wounds of gas gangrene and observe its clinical efficacy. A total of 48 patients with open traumatic gas gangrene infection were included in this study. Amputations were done for 27 patients, and limb salvage procedures were performed for the others. After amputation or aggressive debridement, the VSD system, including polyvinyl alcohol (PVA) foam dressing and polyurethane (PU) film, with continuous irrigation of 1:5000 potassium permanganate solutions, was applied to the wounds. During the follow-up, all the patients healed without recurrence within 8-18 months. There were four complications. Cardiac arrest during amputation surgery occurred in one patient who suffered from severe septic shock. Emergent resuscitation was performed and the patient returned to stable condition. One patient suffered from mixed infection of Staphylococcal aureus, and a second-stage debridement was performed. One patient suffered from severe pain of the limb after the debridement. Exploratory operation was done and the possible reason was trauma of a local peripheral nerve. Three cases of crush syndrome had dialysis treatment for concomitant renal failure. In conclusion, VSD can convert open wound to closed wound, and evacuate necrotic tissues. Furthermore, potassium permanganate solutions help eliminate anaerobic microenvironment and achieve good therapeutic effect on gas gangrene and mixed infection. VSD with continuous irrigation of potassium permanganate is a novel, simple and feasible alternative for severe traumatic open wounds with gas gangrene infection.

  15. Drip Irrigation for Commercial Vegetable and Fruit Production

    OpenAIRE

    Maughn, Tiffany; Allen, Niel; Drost, Dan

    2017-01-01

    Drip irrigation is a highly efficient irrigation method well suited to many fruit and vegetable row crops. Drip tubing or tape discharges water to the soil through emitters positioned close to the plant. The drip tubing can be placed uncovered on the soil surface, under plastic mulch, buried in the soil, or suspended above the ground (e.g., on a trellis system). Water application rate is relatively low and irrigations are usually frequent. Properly designed and maintained drip-irrigation syst...

  16. Speed control variable rate irrigation

    Science.gov (United States)

    Speed control variable rate irrigation (VRI) is used to address within field variability by controlling a moving sprinkler’s travel speed to vary the application depth. Changes in speed are commonly practiced over areas that slope, pond or where soil texture is predominantly different. Dynamic presc...

  17. First Trials Of Hemp Cultivation For Fiber Applications In The East Of France Irrigation And Fertilization Analysis

    Directory of Open Access Journals (Sweden)

    Lotfi Harrabi

    2017-10-01

    Full Text Available This paper presents results from the first hemp experiments in Aspach-le-bas France carried out during summer 2014. Field trials were performed testing the variety Futura 75 at a seed rate of 50 kgha. Two rain densities have been used to analyse the effect of irrigation on its growth. Seven different configurations have been also studied in this work in order to figure out the best one for the hemp cultivation in this region. The composition of hemp biomass in terms of cellulose hemicellulose and lignine has also been analysed for each configuration.

  18. Nuclear Medicine and Application of Nuclear Techniques in Medicine

    International Nuclear Information System (INIS)

    Wiharto, Kunto

    1996-01-01

    The use of nuclear techniques medicine covers not only nuclear medicine and radiology in strict sense but also determination of body mineral content by neutron activation analysis and x-ray fluorescence technique either in vitro or in vivo, application of radioisotopes as tracers in pharmacology and biochemistry, etc. This paper describes the ideal tracer in nuclear medicine, functional and morphological imaging, clinical aspect and radiation protection in nuclear medicine. Nuclear technique offers facilities and chances related to research activities and services in medicine. The development of diagnostic as well as therapeutic methods using monoclonal antibodies labeled with radioisotope will undoubtedly play an important role in the disease control

  19. Group decision-making techniques for natural resource management applications

    Science.gov (United States)

    Coughlan, Beth A.K.; Armour, Carl L.

    1992-01-01

    This report is an introduction to decision analysis and problem-solving techniques for professionals in natural resource management. Although these managers are often called upon to make complex decisions, their training in the natural sciences seldom provides exposure to the decision-making tools developed in management science. Our purpose is to being to fill this gap. We present a general analysis of the pitfalls of group problem solving, and suggestions for improved interactions followed by the specific techniques. Selected techniques are illustrated. The material is easy to understand and apply without previous training or excessive study and is applicable to natural resource management issues.

  20. Ultrasonic testing technique for users in practical application. Pt. 8

    International Nuclear Information System (INIS)

    Corsepius, H.W.

    1978-01-01

    In the present, eighth part of ultrasonic testing technique for users in practical application, the two methods 1) testing by gap coupling and 2) testing by the dipping technique are treated. By the first method the probe is clamped in a holding device in such manner that a water-filled gap remains between probe and surface. Through this gap the sonic signal gets into the specimen without mechanical contact between probe and specimen taking place. By the dipping technique testing is performed in a tank filled with water, the probe being guided over the specimen under water. (RW) [de

  1. The Temporal Variation of Leaf Water Potential in Pistachio under Irrigated and Non-Irrigated Conditions

    Directory of Open Access Journals (Sweden)

    Yusuf AYDIN

    2014-09-01

    Full Text Available The present study was carried out in the experimental field of Pistachio Research Institute on pistachio trees which has uzun variety that was 30 years old. The aim of this research was to determine the Leaf Water Potential (LWP of Pistacia vera L. under irrigated and non-irrigated conditions. In the study, the leaf water potential of pistachio was investigated under fully irrigated and non irrigated conditions. The leaf water potential values were measured one day before and after irrigation by using pressure chamber technique at the beginning, mid and end of irrigation season. According to the results obtained from measurements, the LWP value at the beginning of the irrigation season was -3.7 MPa at noon time due to relatively high temperature for both treatments. At the time of pre-dawn and sunset, this value increased and reached to - 1.6 MPa due to relatively low temperature. In general, the LWP values during the mid of irrigation season, in the irrigated treatments, reached to almost -2.5 MPa in the non-irrigated treatment and the value was measured as -3.68 MPa.

  2. Natural gas hydrates. Experimental techniques and their applications

    Energy Technology Data Exchange (ETDEWEB)

    Ye, Yuguang; Liu, Changling (eds.) [Qingdao Institute of Marine Geology (China). Gas Hydrate Laboratory

    2013-07-01

    Focuses on gas hydrate experiment in laboratory. Intends to provide practical significant parameters for gas hydrate exploration and exploitation in the oceanic and permafrost environments. Consists of different themes that present up-to-date information on hydrate experiments. ''Natural Gas Hydrates: Experimental Techniques and Their Applications'' attempts to broadly integrate the most recent knowledge in the fields of hydrate experimental techniques in the laboratory. The book examines various experimental techniques in order to provide useful parameters for gas hydrate exploration and exploitation. It provides experimental techniques for gas hydrates, including the detection techniques, the thermo-physical properties, permeability and mechanical properties, geochemical abnormalities, stability and dissociation kinetics, exploitation conditions, as well as modern measurement technologies etc.

  3. International Conference on Soft Computing Techniques and Engineering Application

    CERN Document Server

    Li, Xiaolong

    2014-01-01

    The main objective of ICSCTEA 2013 is to provide a platform for researchers, engineers and academicians from all over the world to present their research results and development activities in soft computing techniques and engineering application. This conference provides opportunities for them to exchange new ideas and application experiences face to face, to establish business or research relations and to find global partners for future collaboration.

  4. Ghana - Agriculture - Irrigation

    Data.gov (United States)

    Millennium Challenge Corporation — The Millennium Development Authority (MiDA) financed the construction of a new irrigation scheme in Kpong and the renovation of two irrigation schemes in Botanga and...

  5. Sustainable irrigation in fruit trees

    Directory of Open Access Journals (Sweden)

    Cristos Xiloyannis

    2010-09-01

    Full Text Available Water management in fruit growing, particularly in areas with high water deficit, low rainfall and limited availability of water for irrigation should aid to save water by: i the choice of high efficiency irrigation methods and their correct management; ii the proper choice of the specie, cultivar and rootstock to optimise plant water use; iii the proper choice of the architecture of the canopy and it’s correct management in order to improve water use efficiency; iv the application of regulated deficit irrigation at growth stages less sensitive to water deficit; v strengthening the role of technical assistance for a rapid transfer of knowledge to the growers on the sustainable use of water in fruit growing.

  6. Sustainable irrigation in fruit trees

    Directory of Open Access Journals (Sweden)

    Cristos Xiloyannis

    Full Text Available Water management in fruit growing, particularly in areas with high water deficit, low rainfall and limited availability of water for irrigation should aid to save water by: i the choice of high efficiency irrigation methods and their correct management; ii the proper choice of the specie, cultivar and rootstock to optimise plant water use; iii the proper choice of the architecture of the canopy and it’s correct management in order to improve water use efficiency; iv the application of regulated deficit irrigation at growth stages less sensitive to water deficit; v strengthening the role of technical assistance for a rapid transfer of knowledge to the growers on the sustainable use of water in fruit growing.

  7. [Continent colostomy and colon irrigation].

    Science.gov (United States)

    Kostov, D; Temelkov, T; Kiriazov, E; Ivanov, K; Ignatov, V; Kobakov, G

    2000-01-01

    The authors have studied a functional activity of a continent colostomy at 20 patients, undergone an abdomeno-perineal extirpation of rectum and carried out periodic colonirrigations, during a period of 6 months. A conus type, closed irrigating system has been used. The degree of an incontinency at patients has been compared before and after the beginning of the colonirrigations. The irrigating procedures have reduced spontaneous defications at patients during a week 28 times and have improved the quality of life significantly. The application of colostomy bags has been restricted in 8 (40%) patients. An intraluminal ultrasonographic investigation has been done at 12 (60%) patients at the end of 6 month irrigating period. No changes of the ultrasonographic image of the precolostomic segment of colon has been observed.

  8. Root canal irrigants

    OpenAIRE

    Kandaswamy, Deivanayagam; Venkateshbabu, Nagendrababu

    2010-01-01

    Successful root canal therapy relies on the combination of proper instrumentation, irrigation, and obturation of the root canal. Of these three essential steps of root canal therapy, irrigation of the root canal is the most important determinant in the healing of the periapical tissues. The primary endodontic treatment goal must thus be to optimize root canal disinfection and to prevent reinfection. In this review of the literature, various irrigants and the interactions between irrigants are...

  9. IRRIGATION USING SOLAR PUMP

    OpenAIRE

    Prof. Nitin P.Choudhary*1 & Ms. Komal Singne2

    2017-01-01

    In this report the described design of a PV and soil moisture sensor based automated irrigation system is introduced. This project aims to provide a human friendly, economical and automated water pumping system which eliminates the problems of over irrigation and helps in irrigation water optimization and manage it in accordance with the availability of water. Our project not only tries to modernize the irrigation practices and ensure the optimum yield by carefully fulfilling the requirements...

  10. Application of a nanofibrous composite membrane to the fertilizer-driven forward osmosis process for irrigation water use.

    Science.gov (United States)

    An, Hee-Kyung; Lee, Chang-Gu; Park, Seong-Jik

    2017-11-01

    In this study, we fabricated a nanofibrous composite (NFC) membrane as a substrate to produce forward osmosis (FO) membranes, and we also assessed the use of liquid fertilizer as a draw solution for the FO process in order to produce agricultural irrigation water. Commercial cellulose triacetate (CTA) and thin-film composite (TFC) FO membranes were included in this study. Under FO tests, the NFC, CTA, and TFC membranes achieved initial osmotic water flux values of 35.31, 6.85, and 3.31 L/m 2 ·h and final osmotic water flux values of 12.62, 6.31, and 3.85 L/m 2  h, respectively. The reason for the high osmotic water flux of the NFC membrane is because its nanofiber layer has low tortuosity, high porosity, and a low thickness, resulting in a reduction in the internal concentration polarization phenomenon. When liquid fertilizer was used as the draw solution, the water flux values in the FO experiments for the NFC, CTA, and TFC membranes were 15.54, 5.46, and 2.54 L/m 2  h. Finally, our results revealed that the FO process using liquid fertilizer as a draw solution can be applied to produce agricultural irrigation water from brackish water and the newly fabricated NFC membrane can be applied to the FO process.

  11. Evaluation of Some Agroecological Characteristics of Basil (Ocimum basilicum L. as Affected by Simultaneous Application of Water-Saving Superabsorbent Hydrogel in Soil and Foliar Application of Humic Acid under Different Irrigation Intervals in a Low Inp

    Directory of Open Access Journals (Sweden)

    M. Jahan

    2016-02-01

    Full Text Available Introduction: Basil (Ocimum basilicum L. is an annual herbaceous plant that belongs to lamiaceae family. This plant is native of India country and other countries in south of Asia. Nowadays, the use of water superabsorbent polymers is increased in agriculture and their role in reducing the drought stress and increasing the crops production has been demonstrated in many researches. Superabsorbent polymers can absorb lots of water and keep it in their structure and give it to plant under drought stress conditions (9. Humic substances are a group of heterogeneous molecules that are bonded together by weak forces, therefore they have high chemical stability. Humic acid comprise 65 to 80 percent of total soil organic matter (6. According to medicinal importance of Basil and its roles in the food and pharmaceutical industries, beside the limited water resources and need to increase water use efficiency through using ecological inputs, this study designed and conducted aimed to evaluate agroecological characteristics of Basil as affected by application of water-saving superabsorbent and humic acid under irrigation intervals. Materials and Methods: In order to evaluate the effects of different amounts of water-saving superabsorbent and foliar application of humic acid and irrigation intervals on some quantitative characteristics of basil (Ocimum basilicum L., a split strip plot experiment was conducted based on RCBD design with three replications at The Research Farm of Ferdowsi University of Mashhad, Iran during growing season of 2012-13. Experimental factors included three levels of water-saving superabsorbent (0, 40 and 80 kg ha-1 as the main plot factor, two levels of humic acid (0 and 3 kg ha-1 as the sub plot factor and two levels of irrigation interval (5 and 10 days as the strip plot factor. Studied traits were seed number and weight per plant, plant height, number of lateral branches per plant, seed yield, biological yield and harvest index

  12. The development and application of high-capacity thickening techniques

    International Nuclear Information System (INIS)

    Ji Zhenwan; Song Yuejie

    1995-01-01

    On the basis of sedimentation theory and comparison between the high-capacity and conventional thickening techniques, the authors analyse the ways to increase capacity and to improve technological parameters of thickeners, describes the construction features, development, application, automatic control and test installations of high-capacity thickeners at home and abroad

  13. 48 CFR 9904.408-50 - Techniques for application.

    Science.gov (United States)

    2010-10-01

    .... 9904.408-50 Section 9904.408-50 Federal Acquisition Regulations System COST ACCOUNTING STANDARDS BOARD, OFFICE OF FEDERAL PROCUREMENT POLICY, OFFICE OF MANAGEMENT AND BUDGET PROCUREMENT PRACTICES AND COST ACCOUNTING STANDARDS COST ACCOUNTING STANDARDS 9904.408-50 Techniques for application. (a) Determinations...

  14. 48 CFR 9904.415-50 - Techniques for application.

    Science.gov (United States)

    2010-10-01

    ... deferred compensation for each cost accounting period shall be the present value of the future benefits of.... 9904.415-50 Section 9904.415-50 Federal Acquisition Regulations System COST ACCOUNTING STANDARDS BOARD... ACCOUNTING STANDARDS COST ACCOUNTING STANDARDS 9904.415-50 Techniques for application. (a) The contractor...

  15. On the applicability of schema integration techniques to database interoperation

    NARCIS (Netherlands)

    Vermeer, Mark W.W.; Apers, Peter M.G.

    1996-01-01

    We discuss the applicability of schema integration techniques developed for tightly-coupled database interoperation to interoperation of databases stemming from different modelling contexts. We illustrate that in such an environment, it is typically quite difficult to infer the real-world semantics

  16. 48 CFR 9904.416-50 - Techniques for application.

    Science.gov (United States)

    2010-10-01

    ... ACCOUNTING STANDARDS COST ACCOUNTING STANDARDS 9904.416-50 Techniques for application. (a) Measurement of.... 9904.416-50 Section 9904.416-50 Federal Acquisition Regulations System COST ACCOUNTING STANDARDS BOARD... be assigned pro rata among the cost accounting periods covered by the policy term, except as provided...

  17. Application of integrated modeling technique for data services ...

    African Journals Online (AJOL)

    This paper, therefore, describes the application of the integrated simulation technique for deriving the optimum resources required for data services in an asynchronous transfer mode (ATM) based private wide area network (WAN) to guarantee specific QoS requirement. The simulation tool drastically cuts the simulation ...

  18. Application for trackless mining technique in Benxi uranium mine

    International Nuclear Information System (INIS)

    Chen Bingguo

    1998-01-01

    The author narrates the circumstances achieving constructional target in Benxi Uranium Mine under relying on advance of science and technology and adopting small trackless mining equipment, presents the application of trackless mining equipment at mining small mine and complex mineral deposit and discusses the unique superiority of trackless mining technique in development work, mining preparation work and backstoping

  19. 48 CFR 9904.407-50 - Techniques for application.

    Science.gov (United States)

    2010-10-01

    .... 9904.407-50 Section 9904.407-50 Federal Acquisition Regulations System COST ACCOUNTING STANDARDS BOARD, OFFICE OF FEDERAL PROCUREMENT POLICY, OFFICE OF MANAGEMENT AND BUDGET PROCUREMENT PRACTICES AND COST ACCOUNTING STANDARDS COST ACCOUNTING STANDARDS 9904.407-50 Techniques for application. (a)(1) A contractor's...

  20. 48 CFR 9904.417-50 - Techniques for application.

    Science.gov (United States)

    2010-10-01

    ... capitalized, such as the method used for financial accounting and reporting, may be used, provided the.... 9904.417-50 Section 9904.417-50 Federal Acquisition Regulations System COST ACCOUNTING STANDARDS BOARD... ACCOUNTING STANDARDS COST ACCOUNTING STANDARDS 9904.417-50 Techniques for application. (a) The cost of money...

  1. Application of nuclear analysis techniques in ancient chinese porcelain

    International Nuclear Information System (INIS)

    Feng Songlin; Xu Qing; Feng Xiangqian; Lei Yong; Cheng Lin; Wang Yanqing

    2005-01-01

    Ancient ceramic was fired with porcelain clay. It contains various provenance information and age characteristic. It is the scientific foundation of studying Chinese porcelain to analyze and research the ancient ceramic with modern analysis methods. According to the property of nuclear analysis technique, its function and application are discussed. (authors)

  2. 48 CFR 9904.401-50 - Techniques for application.

    Science.gov (United States)

    2010-10-01

    .... 9904.401-50 Section 9904.401-50 Federal Acquisition Regulations System COST ACCOUNTING STANDARDS BOARD, OFFICE OF FEDERAL PROCUREMENT POLICY, OFFICE OF MANAGEMENT AND BUDGET PROCUREMENT PRACTICES AND COST ACCOUNTING STANDARDS COST ACCOUNTING STANDARDS 9904.401-50 Techniques for application. (a) The standard...

  3. 48 CFR 9904.405-50 - Techniques for application.

    Science.gov (United States)

    2010-10-01

    .... 9904.405-50 Section 9904.405-50 Federal Acquisition Regulations System COST ACCOUNTING STANDARDS BOARD, OFFICE OF FEDERAL PROCUREMENT POLICY, OFFICE OF MANAGEMENT AND BUDGET PROCUREMENT PRACTICES AND COST ACCOUNTING STANDARDS COST ACCOUNTING STANDARDS 9904.405-50 Techniques for application. (a) The detail and...

  4. 48 CFR 9904.403-50 - Techniques for application.

    Science.gov (United States)

    2010-10-01

    .... 9904.403-50 Section 9904.403-50 Federal Acquisition Regulations System COST ACCOUNTING STANDARDS BOARD, OFFICE OF FEDERAL PROCUREMENT POLICY, OFFICE OF MANAGEMENT AND BUDGET PROCUREMENT PRACTICES AND COST ACCOUNTING STANDARDS COST ACCOUNTING STANDARDS 9904.403-50 Techniques for application. (a)(1) Separate...

  5. 48 CFR 9904.406-50 - Techniques for application.

    Science.gov (United States)

    2010-10-01

    .... 9904.406-50 Section 9904.406-50 Federal Acquisition Regulations System COST ACCOUNTING STANDARDS BOARD, OFFICE OF FEDERAL PROCUREMENT POLICY, OFFICE OF MANAGEMENT AND BUDGET PROCUREMENT PRACTICES AND COST ACCOUNTING STANDARDS COST ACCOUNTING STANDARDS 9904.406-50 Techniques for application. (a) The cost of an...

  6. 48 CFR 9904.404-50 - Techniques for application.

    Science.gov (United States)

    2010-10-01

    .... 9904.404-50 Section 9904.404-50 Federal Acquisition Regulations System COST ACCOUNTING STANDARDS BOARD, OFFICE OF FEDERAL PROCUREMENT POLICY, OFFICE OF MANAGEMENT AND BUDGET PROCUREMENT PRACTICES AND COST ACCOUNTING STANDARDS COST ACCOUNTING STANDARDS 9904.404-50 Techniques for application. (a) The cost to...

  7. 48 CFR 9904.414-50 - Techniques for application.

    Science.gov (United States)

    2010-10-01

    ... the case of process cost accounting systems, the contracting parties may agree to substitute an.... 9904.414-50 Section 9904.414-50 Federal Acquisition Regulations System COST ACCOUNTING STANDARDS BOARD... ACCOUNTING STANDARDS COST ACCOUNTING STANDARDS 9904.414-50 Techniques for application. (a) The investment...

  8. Irrigation in endodontic treatment.

    Science.gov (United States)

    Basrani, Bettina

    2011-01-01

    The primary endodontic treatment goal is to optimize root canal disinfection and to prevent reinfection. Successful root canal therapy relies on the combination of proper instrumentation, irrigation, and obturation of the root canal system. In this review of the literature, various irrigants and the interactions between irrigants are discussed and new delivery systems are introduced.

  9. Basin Irrigation Design with Multi-Criteria Analysis Focusing on Water Saving and Economic Returns: Application to Wheat in Hetao, Yellow River Basin

    Directory of Open Access Journals (Sweden)

    Qingfeng Miao

    2018-01-01

    Full Text Available The sustainability of the Hetao Irrigation System, located in the water scarce upper Yellow River basin, is a priority considering the need for water saving, increased water productivity, and higher farmers’ incomes. The upgrading of basin irrigation, the main irrigation method, is essential and includes the adoption of precise land levelling, cut-off management, improved water distribution uniformity, and adequate irrigation scheduling. With this objective, the current study focuses on upgrading wheat basin irrigation through improved design using a decision support system (DSS model, which considers land parcels characteristics, crop irrigation scheduling, soil infiltration, hydraulic simulation, and environmental and economic impacts. Its use includes outlining water saving scenarios and ranking alternative designs through multi-criteria analysis considering the priorities of stakeholders. The best alternatives concern flat level basins with a 100 and 200 m length and inflow rates between 2 and 4 L s−1 m−1. The total irrigation cost of designed projects, including the cost of the autumn irrigation, varies between 2400 and 3300 Yuan ha−1; the major cost component is land levelling, corresponding to 33–46% of total irrigation costs. The economic land productivity is about 18,000 Yuan ha−1. The DSS modelling defined guidelines to be applied by an extension service aimed at implementing better performing irrigation practices, and encouraged a good interaction between farmers and the Water Users Association, thus making easier the implementation of appropriate irrigation management programs.

  10. Development of a tentacle propulsion technique for underwater application

    International Nuclear Information System (INIS)

    Alamgir, T; Rashid, M M; Khan, M R

    2013-01-01

    As robotic technology matures and more platforms are fielded in unstructured real-world situations, the more new areas of applications are being thought for robotic deployment. After successes in industrial robots, researchers are now trying to explore new robots with biological features of different biological creatures like, snake, bird, and spider for their stunning advantages. Underwater exploration using robots is a new avenue. Research on the tentacle robot for underwater application is a new field of research besides the other research in this arena. There are few researches on this topic are explored and mostly are on biological robot. Besides those researches this paper aims to propose and demonstrate another technique to build a tentacle for propulsion purposes. Therefore, in this paper will discuss more on mathematical development for the propulsion technique and its software verification technique in considering the environmental constrains

  11. Applications of radiations, radioisotopes and nuclear techniques in biotechnology

    International Nuclear Information System (INIS)

    Bhatia, C.R.

    1994-01-01

    Applications of radiations, radioisotopes and other nuclear techniques has contributed a great deal in our understanding of microbial plant and animal biochemistry and molecular biology. Electron microscopy has provided visual evidence for molecular events. Developments in cell tissue culture of both plants and animals and immunology have contributed to advances in what we now refer as biotechnology. This paper focuses on the applications in the high-tech end of biotechnology, limited to the use of recombinant-DNA techniques. Molecular identification of the genes, their cloning and horizontal transfer across the species of microbes, plants and animals and expression of the transferred genes is the major strength of modern biotechnology. The techniques described in this paper have played a significant role in the development of biotechnology. 6 refs

  12. Scanning tunneling microscopy II further applications and related scanning techniques

    CERN Document Server

    Güntherodt, Hans-Joachim

    1995-01-01

    Scanning Tunneling Microscopy II, like its predecessor, presents detailed and comprehensive accounts of the basic principles and broad range of applications of STM and related scanning probe techniques. The applications discussed in this volume come predominantly from the fields of electrochemistry and biology. In contrast to those described in STM I, these studies may be performed in air and in liquids. The extensions of the basic technique to map other interactions are described in chapters on scanning force microscopy, magnetic force microscopy, and scanning near-field optical microscopy, together with a survey of other related techniques. Also described here is the use of a scanning proximal probe for surface modification. Together, the two volumes give a comprehensive account of experimental aspects of STM. They provide essential reading and reference material for all students and researchers involved in this field. In this second edition the text has been updated and new methods are discussed.

  13. Scanning tunneling microscopy II further applications and related scanning techniques

    CERN Document Server

    Güntherodt, Hans-Joachim

    1992-01-01

    Scanning Tunneling Microscopy II, like its predecessor, presents detailed and comprehensive accounts of the basic principles and broad range of applications of STM and related scanning probe techniques. The applications discussed in this volume come predominantly from the fields of electrochemistry and biology. In contrast to those described in Vol. I, these sudies may be performed in air and in liquids. The extensions of the basic technique to map other interactions are described inchapters on scanning force microscopy, magnetic force microscopy, scanning near-field optical microscopy, together with a survey of other related techniques. Also described here is the use of a scanning proximal probe for surface modification. Togehter, the two volumes give a comprehensive account of experimental aspcets of STM. They provide essentialreading and reference material for all students and researchers involvedin this field.

  14. Conference on Techniques of Nuclear and Conventional Analysis and Applications

    International Nuclear Information System (INIS)

    2012-01-01

    Full text : With their wide scope, particularly in the areas of environment, geology, mining, industry and life sciences; analysis techniques are of great importance in research as fundamental and applied. The Conference on Techniques for Nuclear and Conventional Analysis and Applications (TANCA) are Registered in the national strategy of opening of the University and national research centers on their local, national and international levels. This conference aims to: Promoting nuclear and conventional analytical techniques; Contribute to the creation of synergy between the different players involved in these techniques include, Universities, Research Organizations, Regulatory Authorities, Economic Operators, NGOs and others; Inform and educate potential users of the performance of these techniques; Strengthen exchanges and links between researchers, industry and policy makers; Implement a program of inter-laboratory comparison between Moroccan one hand, and their foreign counterparts on the other; Contribute to the research training of doctoral students and postdoctoral scholars. Given the relevance and importance of the issues related to environment and impact on cultural heritage, this fourth edition of TANCA is devoted to the application of analytical techniques for conventional and nuclear Questions ied to environment and its impact on cultural heritage.

  15. Usability evaluation techniques in mobile commerce applications: A systematic review

    Science.gov (United States)

    Hussain, Azham; Mkpojiogu, Emmanuel O. C.

    2016-08-01

    Obviously, there are a number of literatures concerning the usability of mobile commerce (m-commerce) applications and related areas, but they do not adequately provide knowledge about usability techniques used in most of the empirical usability evaluation for m-commerce application. Therefore, this paper is aimed at producing the usability techniques frequently used in the aspect of usability evaluation for m-commerce applications. To achieve the stated objective, systematic literature review was employed. Sixty seven papers were downloaded in usability evaluation for m-commerce and related areas; twenty one most relevant studies were selected for review in order to extract the appropriate information. The results from the review shows that heuristic evaluation, formal test and think aloud methods are the most commonly used methods in m-commerce application in comparison to cognitive walkthrough and the informal test methods. Moreover, most of the studies applied control experiment (33.3% of the total studies); other studies that applied case study for usability evaluation are 14.28%. The results from this paper provide additional knowledge to the usability practitioners and research community for the current state and use of usability techniques in m-commerce application.

  16. Potato yield and yield structure depending on irrigation

    Directory of Open Access Journals (Sweden)

    Milić Stanko

    2010-01-01

    Full Text Available In the agroclimatic conditions of the Vojvodina Province, the application of an economic water regime and modern technology is necessary for stable and intensive potato production. A two-year experiment on calcareous chernozem was carried out to determine how irrigation and different pre-irrigation soil moisture affect potato yield and distribution of tuber fraction in the potato yield. The block-design trial had four replicates and was adapted for sprinkler irrigation conditions. It included four treatments: irrigation with pre-irrigation moisture levels of 60 % of field water capacity (FC, irrigation with pre-irrigation moisture levels of 70 % (FC, irrigation with pre-irrigation moisture levels of 80% (FC, and a non-irrigated control treatment. Irrigation significantly increased the yield of potato, which increased from 37.27 % to 75.86 %. Under irrigation, the percentage of small fractions decreased in favour of the 55 mm one, or fractions above the 45-55 mm range. On average, irrigated treatments produced significantly more tubers than the conditions of natural water supply. .

  17. Simulation tools for industrial applications of phased array inspection techniques

    International Nuclear Information System (INIS)

    Mahaut, St.; Roy, O.; Chatillon, S.; Calmon, P.

    2001-01-01

    Ultrasonic phased arrays techniques have been developed at the French Atomic Energy Commission in order to improve defects characterization and adaptability to various inspection configuration (complex geometry specimen). Such transducers allow 'standard' techniques - adjustable beam-steering and focusing -, or more 'advanced' techniques - self-focusing on defects for instance -. To estimate the performances of those techniques, models have been developed, which allows to compute the ultrasonic field radiated by an arbitrary phased array transducer through any complex specimen, and to predict the ultrasonic response of various defects inspected with a known beam. Both modeling applications are gathered in the Civa software, dedicated to NDT expertise. The use of those complementary models allows to evaluate the ability of a phased array to steer and focus the ultrasonic beam, and therefore its relevancy to detect and characterize defects. These models are specifically developed to give accurate solutions to realistic inspection applications. This paper briefly describes the CIVA models, and presents some applications dedicated to the inspection of complex specimen containing various defects with a phased array used to steer and focus the beam. Defect detection and characterization performances are discussed for the various configurations. Some experimental validation of both models are also presented. (authors)

  18. The phenology of malaria mosquitos in irrigated rice fields in Mali

    NARCIS (Netherlands)

    Klinkenberg, E.; Takken, W.; Huibers, F.P.; Touré, Y.T.

    2003-01-01

    A field study was carried out in the large-scale rice irrigation scheme of the Office du Niger in Mali to investigate the relation between anopheline mosquito larval development and small-scale differences in irrigation practices, such as water level, irrigation application and irrigation frequency.

  19. Photogrammetry: applications of a three-dimensional remote measurement technique

    International Nuclear Information System (INIS)

    Peak, K.

    1988-01-01

    Photogrammetry is defined as the precise art of abstracting measurements from photographic images. Used for many years as a means to produce the world's maps, it has, in recent years, been applied in many engineering environments. The nuclear industry has, in particular, benefitted from the close range applications of photogrammetry. This paper sets out to describe the techniques involved, from the site photography through to the analytical data extraction. It will include a number of examples of where photogrammetry has been used in the nuclear industry as a remote measurement technique, from simple monitoring exercises to the compilation of complex three-dimensional as-built computer models. (author)

  20. Application of the PRBS/FFT technique to digital simulations

    International Nuclear Information System (INIS)

    Hinds, H.W.

    1977-01-01

    This paper describes a method for obtaining a small-signal frequency response from a digital dynamic simulation. It employs a modified form of the PRBS/FFT technique, whereby a system is perturbed by a pseudo-random binary sequence and its response is analyzed using a fast Fourier transform-based program. Two applications of the technique are described; one involves a set of two coupled, second-order, ordinary differential equations; the other is a set of non-linear partial differential equations describing the thermohydraulic behaviour of water boiling in a fuel channel. (author)

  1. Validation Techniques for Sensor Data in Mobile Health Applications

    Directory of Open Access Journals (Sweden)

    Ivan Miguel Pires

    2016-01-01

    Full Text Available Mobile applications have become a must in every user’s smart device, and many of these applications make use of the device sensors’ to achieve its goal. Nevertheless, it remains fairly unknown to the user to which extent the data the applications use can be relied upon and, therefore, to which extent the output of a given application is trustworthy or not. To help developers and researchers and to provide a common ground of data validation algorithms and techniques, this paper presents a review of the most commonly used data validation algorithms, along with its usage scenarios, and proposes a classification for these algorithms. This paper also discusses the process of achieving statistical significance and trust for the desired output.

  2. Application of ESPI techniques for the study of dynamic vibrations

    Science.gov (United States)

    Krupka, Rene

    2004-06-01

    Full field optical measurement techniques have already entered into various fields of industrial applications covering static as well as dynamic phenomena. The electronic speckle pattern interferometry (ESPI) allows the non contact, sensitive and three dimensional measurement of displacements in the sub micron range of objects with dimensions from mm2 to m2. For dynamic and transient phenomena, the use of pulsed laser have already been reported for various applications and successfully proven for the determination of the structural response of different components. In this paper we would like to present recent developments in the field of pulsed ESPI applications where emphasis is put onto the full field measurement result. The use of a completely computer controlled system allows easy access to mode shape characterization, deformation measurements and the characterization of transient events like shock wave propagation. Recent developments of the 3D-PulseESPI technique led to a very compact and complete system with improved characteristics regarding robustness and operation. The integrated design of the illumination laser and sensors for image acquisition allows easy aiming and adjustments with respect to the object of inspection. The laser is completely computer controlled which is advantageously used in a completely automatic brake squeal inspection system, which captures the squealing signal, automatically fires the laser and provides the complete deformation map of the component under test. Examples of recent applications in the field of dynamic structure response, with an emphasis in the field of automotive applications are given.

  3. Cloud computing and digital media fundamentals, techniques, and applications

    CERN Document Server

    Li, Kuan-Ching; Shih, Timothy K

    2014-01-01

    Cloud Computing and Digital Media: Fundamentals, Techniques, and Applications presents the fundamentals of cloud and media infrastructure, novel technologies that integrate digital media with cloud computing, and real-world applications that exemplify the potential of cloud computing for next-generation digital media. It brings together technologies for media/data communication, elastic media/data storage, security, authentication, cross-network media/data fusion, interdevice media interaction/reaction, data centers, PaaS, SaaS, and more.The book covers resource optimization for multimedia clo

  4. Advances in dental veneers: materials, applications, and techniques.

    Science.gov (United States)

    Pini, Núbia Pavesi; Aguiar, Flávio Henrique Baggio; Lima, Débora Alves Nunes Leite; Lovadino, José Roberto; Terada, Raquel Sano Suga; Pascotto, Renata Corrêa

    2012-01-01

    Laminate veneers are a conservative treatment of unaesthetic anterior teeth. The continued development of dental ceramics offers clinicians many options for creating highly aesthetic and functional porcelain veneers. This evolution of materials, ceramics, and adhesive systems permits improvement of the aesthetic of the smile and the self-esteem of the patient. Clinicians should understand the latest ceramic materials in order to be able to recommend them and their applications and techniques, and to ensure the success of the clinical case. The current literature was reviewed to search for the most important parameters determining the long-term success, correct application, and clinical limitations of porcelain veneers.

  5. Literature survey of heat transfer enhancement techniques in refrigeration applications

    Energy Technology Data Exchange (ETDEWEB)

    Jensen, M.K.; Shome, B. [Rensselaer Polytechnic Inst., Troy, NY (United States). Dept. of Mechanical Engineering, Aeronautical Engineering and Mechanics

    1994-05-01

    A survey has been performed of the technical and patent literature on enhanced heat transfer of refrigerants in pool boiling, forced convection evaporation, and condensation. Extensive bibliographies of the technical literature and patents are given. Many passive and active techniques were examined for pure refrigerants, refrigerant-oil mixtures, and refrigerant mixtures. The citations were categorized according to enhancement technique, heat transfer mode, and tube or shell side focus. The effects of the enhancement techniques relative to smooth and/or pure refrigerants were illustrated through the discussion of selected papers. Patented enhancement techniques also are discussed. Enhanced heat transfer has demonstrated significant improvements in performance in many refrigerant applications. However, refrigerant mixtures and refrigerant-oil mixtures have not been studied extensively; no research has been performed with enhanced refrigerant mixtures with oil. Most studies have been of the parametric type; there has been inadequate examination of the fundamental processes governing enhanced refrigerant heat transfer, but some modeling is being done and correlations developed. It is clear that an enhancement technique must be optimized for the refrigerant and operating condition. Fundamental processes governing the heat transfer must be examined if models for enhancement techniques are to be developed; these models could provide the method to optimize a surface. Refrigerant mixtures, with and without oil present, must be studied with enhancement devices; there is too little known to be able to estimate the effects of mixtures (particularly NARMs) with enhanced heat transfer. Other conclusions and recommendations are offered.

  6. Application of digital sampling techniques to particle identification

    International Nuclear Information System (INIS)

    Bardelli, L.; Poggi, G.; Bini, M.; Carraresi, L.; Pasquali, G.; Taccetti, N.

    2003-01-01

    An application of digital sampling techniques is presented which can greatly simplify experiments involving sub-nanosecond time-mark determinations and energy measurements with nuclear detectors, used for Pulse Shape Analysis and Time of Flight measurements in heavy ion experiments. In this work a 100 M Sample/s, 12 bit analog to digital converter has been used: examples of this technique applied to Silicon and CsI(Tl) detectors in heavy-ions experiments involving particle identification via Pulse Shape analysis and Time of Flight measurements are presented. The system is suited for applications to large detector arrays and to different kinds of detectors. Some preliminary results regarding the simulation of current signals in Silicon detectors are also discussed. (authors)

  7. Expert system reasoning techniques applicable to the electric power industry

    International Nuclear Information System (INIS)

    Touchton, R.A.

    1987-01-01

    This paper describes the applicability of three problem solving paradigms adopted from the artificial intelligence discipline of computer sciences, which have been used in developing nuclear plant expert systems. Each technique is briefly defined and an example is presented that shows how that technique was used in developing an expert system application prototype. The three paradigms and their associated example systems are: (1) rule-based reasoning: reactor emergency action level monitor (REALM) for the Electric Power Research Institute, (2) object-oriented programming: accident diagnosis and prognosis aid for the US Department of Energy, and (3) model-based reasoning: knowledge-based monitoring and control system for the Electric Power Research Institute

  8. Application of identification techniques to remote manipulator system flight data

    Science.gov (United States)

    Shepard, G. D.; Lepanto, J. A.; Metzinger, R. W.; Fogel, E.

    1983-01-01

    This paper addresses the application of identification techniques to flight data from the Space Shuttle Remote Manipulator System (RMS). A description of the remote manipulator, including structural and control system characteristics, sensors, and actuators is given. A brief overview of system identification procedures is presented, and the practical aspects of implementing system identification algorithms are discussed. In particular, the problems posed by desampling rate, numerical error, and system nonlinearities are considered. Simulation predictions of damping, frequency, and system order are compared with values identified from flight data to support an evaluation of RMS structural and control system models. Finally, conclusions are drawn regarding the application of identification techniques to flight data obtained from a flexible space structure.

  9. Performance of fertigation technique for phosphorus application in cotton

    Directory of Open Access Journals (Sweden)

    M. Aslam

    2009-05-01

    Full Text Available Low native soil phosphorus availability coupled with poor utilization of added phosphorus is one of the major constraints limiting the productivity of the crops. With a view of addressing this issue, field studies were conducted to compare the relative efficacy of broadcast and fertigation techniques for phosphorus application during 2005-2006 using cotton as a test crop. Two methods of phosphorus application i.e. broadcast and fertigation were evaluated using five levels of P2O5 (0, 30, 45, 60 and 75 kg P2O5 ha -1. Fertigation showed an edge over broadcast method at all levels of phosphorus application. The highest seed cotton yield was recorded with 75 kg P2O5 ha-1. Fertilizer phosphorus applied at the rate of 60 kg ha-1 through fertigation produced 3.4 tons ha-1 of seed cotton yield, which was statistically identical to 3.3 tons recorded with 75 kg ha-1 of broadcast phosphorus. Agronomic performance of phosphorus was influenced considerably by either method of fertilizer application. The seed cotton yield per kg of fertigation phosphorus was 48% higher than the corresponding broadcast application. The results of these studies showed that fertigation was the most efficient method of phosphorus application compared with the conventional broadcast application of fertilizers.

  10. Application of near-surface geophysics as part of a hydrologic study of a subsurface drip irrigation system along the Powder River floodplain near Arvada, Wyoming

    Science.gov (United States)

    Sams, James I.; Veloski, Garret; Smith, Bruce D.; Minsley, Burke J.; Engle, Mark A.; Lipinski, Brian A.; Hammack, Richard W.; Zupancic, John W.

    2014-01-01

    Rapid development of coalbed natural gas (CBNG) production in the Powder River Basin (PRB) of Wyoming has occurred since 1997. National attention related to CBNG development has focused on produced water management, which is the single largest cost for on-shore domestic producers. Low-cost treatment technologies allow operators to reduce their disposal costs, provide treated water for beneficial use, and stimulate oil and gas production by small operators. Subsurface drip irrigation (SDI) systems are one potential treatment option that allows for increased CBNG production by providing a beneficial use for the produced water in farmland irrigation.Water management practices in the development of CBNG in Wyoming have been aided by integrated geophysical, geochemical, and hydrologic studies of both the disposal and utilization of water. The U.S. Department of Energy (DOE) National Energy Technology Laboratory (NETL) and the U.S. Geological Survey (USGS) have utilized multi-frequency airborne, ground, and borehole electromagnetic (EM) and ground resistivity methods to characterize the near-surface hydrogeology in areas of produced water disposal. These surveys provide near-surface EM data that can be compared with results of previous surveys to monitor changes in soils and local hydrology over time as the produced water is discharged through SDI.The focus of this investigation is the Headgate Draw SDI site, situated adjacent to the Powder River near the confluence of a major tributary, Crazy Woman Creek, in Johnson County, Wyoming. The SDI system was installed during the summer of 2008 and began operation in October of 2008. Ground, borehole, and helicopter electromagnetic (HEM) conductivity surveys were conducted at the site prior to the installation of the SDI system. After the installation of the subsurface drip irrigation system, ground EM surveys have been performed quarterly (weather permitting). The geophysical surveys map the heterogeneity of the near

  11. New applications of photographic materials in science and technique

    International Nuclear Information System (INIS)

    Buschmann, H.T.; Deml, R.; Duville, R.; Philippaerts, H.; Bollen, R.; Ranz, E.

    1976-01-01

    In spite of some disatvantages photographic materials based on silver halides possess the outstanding feature of high sensitivity. So again and again special photographic materials have been developed for new techniques including information storage. This contribution reports on some special photographic materials and it briefly discusses some applications. Materials are discussed in detail for holography, carrier-frequency photography, producing masks for integrated circuits, recording equidensities, bubble chamber photography, and for neutron-radiography. (orig.) [de

  12. An introduction to synchrotron radiation techniques and applications

    CERN Document Server

    Willmott, Philip

    2011-01-01

    This book introduces the reader to the basic concepts of the generation and manipulation of synchrotron light, its interaction with matter, and the application of synchrotron light in the “classical” techniques, while including some of the most modern technological developments. As much as possible, complicated mathematical derivations and formulas are avoided. A more heuristic approach is adopted, whereby the general physical reasoning behind the equations is highlighted.

  13. Applications of nuclear technique in environmental and medical science

    International Nuclear Information System (INIS)

    Shi Xianfeng; Shen Hao; Liu Bo; Sun Minde; Yao Huiying; Zhou Shijun; Mi Yong

    2001-01-01

    The serious environmental pollution problem and application of the nuclear technique in environmental and medical sciences were discussed. The analysed results of the elemental distribution of particles in automobile exhaust, the aerosol particle of different size and the effect of Rare Earth on cells were reported. The authors can obtain some information related to element concentration. It offers a convenient method in inspecting the environmental pollution

  14. Internet tomography an introduction to concepts, techniques, tools and applications

    CERN Document Server

    Moloisane, Abia; O’Droma, Máirtín

    2013-01-01

    Internet tomography, introduced from basic principles through to techniques, tools and applications, is the subject of this book. The design of Internet Tomography Measurement Systems (ITMS) aimed at mapping the Internet performance profile spatially and temporally over paths between probing stations is a particular focus.The Internet Tomography Measurement System design criteria addressed include:Minimally-invasive, independent and autonomous, active or passive measurement;Flexibility and scalability;Capability of targeting local, regional and global Internet paths and underlying IP networks;

  15. Analysis of deployment techniques for webbased applications in SMEs

    OpenAIRE

    Browne, Cathal

    2011-01-01

    The Internet is no longer just a source for accessing information; it has become a valuable medium for social networking and software services. Web-browsers can now access entire software systems available online to provide the user with a range of services. The concept of software as a service(SAAS) was born out of this. The number of development techniques and frameworks for such web-applications has grown rapidly and much research and development has been carried out on adva...

  16. Imaging of the hip and bony pelvis. Techniques and applications

    Energy Technology Data Exchange (ETDEWEB)

    Davies, A.M. [Royal Orthopaedic Hospital, Birmingham (United Kingdom). MRI Centre; Johnson, K.J. [Princess of Wales Birmingham Children' s Hospital (United Kingdom); Whitehouse, R.W. (eds.) [Manchester Royal Infirmary (United Kingdom). Dept. of Clinical Radiology

    2006-07-01

    This is a comprehensive textbook on imaging of the bony pelvis and hip joint that provides a detailed description of the techniques and imaging findings relevant to this complex anatomical region. In the first part of the book, the various techniques and procedures employed for imaging the pelvis and hip are discussed in detail. The second part of the book documents the application of these techniques to the diverse clinical problems and diseases encountered. Among the many topics addressed are congenital and developmental disorders including developmental dysplasia of the hip, irritable hip and septic arthritis, Perthes' disease and avascular necrosis, slipped upper femoral epiphysis, bony and soft tissue trauma, arthritis, tumours and hip prostheses. Each chapter is written by an acknowledged expert in the field, and a wealth of illustrative material is included. This book will be of great value to musculoskeletal and general radiologists, orthopaedic surgeons and rheumatologists. (orig.)

  17. On the Application of TLS Techniques to AC Electrical Drives

    Directory of Open Access Journals (Sweden)

    M. Cirrincione

    2005-03-01

    Full Text Available This paper deals with the application of a new neuron, the TLS EXIN neuron, to AC induction motor drives. In particular, it addresses two important subjects of AC induction motor drives: the on-line estimation of the electrical parameters of the machine and the speed estimation in sensorless drives. On this basis, this work summarizes the parameter estimation and sensorless techniques already developed by the authors over these last few years, all based on the TLS EXIN. With regard to sensorless, two techniques are proposed: one based on the MRAS and the other based on the full-order Luenberger observer. The work show some of the most significant results obtained by the authors in these fields and stresses the important potentiality of this new neural technique in AC induction machine drives.

  18. Aircraft applications of fault detection and isolation techniques

    Science.gov (United States)

    Marcos Esteban, Andres

    In this thesis the problems of fault detection & isolation and fault tolerant systems are studied from the perspective of LTI frequency-domain, model-based techniques. Emphasis is placed on the applicability of these LTI techniques to nonlinear models, especially to aerospace systems. Two applications of Hinfinity LTI fault diagnosis are given using an open-loop (no controller) design approach: one for the longitudinal motion of a Boeing 747-100/200 aircraft, the other for a turbofan jet engine. An algorithm formalizing a robust identification approach based on model validation ideas is also given and applied to the previous jet engine. A general linear fractional transformation formulation is given in terms of the Youla and Dual Youla parameterizations for the integrated (control and diagnosis filter) approach. This formulation provides better insight into the trade-off between the control and the diagnosis objectives. It also provides the basic groundwork towards the development of nested schemes for the integrated approach. These nested structures allow iterative improvements on the control/filter Youla parameters based on successive identification of the system uncertainty (as given by the Dual Youla parameter). The thesis concludes with an application of Hinfinity LTI techniques to the integrated design for the longitudinal motion of the previous Boeing 747-100/200 model.

  19. Virtual 3d City Modeling: Techniques and Applications

    Science.gov (United States)

    Singh, S. P.; Jain, K.; Mandla, V. R.

    2013-08-01

    3D city model is a digital representation of the Earth's surface and it's related objects such as Building, Tree, Vegetation, and some manmade feature belonging to urban area. There are various terms used for 3D city models such as "Cybertown", "Cybercity", "Virtual City", or "Digital City". 3D city models are basically a computerized or digital model of a city contains the graphic representation of buildings and other objects in 2.5 or 3D. Generally three main Geomatics approach are using for Virtual 3-D City models generation, in first approach, researcher are using Conventional techniques such as Vector Map data, DEM, Aerial images, second approach are based on High resolution satellite images with LASER scanning, In third method, many researcher are using Terrestrial images by using Close Range Photogrammetry with DSM & Texture mapping. We start this paper from the introduction of various Geomatics techniques for 3D City modeling. These techniques divided in to two main categories: one is based on Automation (Automatic, Semi-automatic and Manual methods), and another is Based on Data input techniques (one is Photogrammetry, another is Laser Techniques). After details study of this, finally in short, we are trying to give the conclusions of this study. In the last, we are trying to give the conclusions of this research paper and also giving a short view for justification and analysis, and present trend for 3D City modeling. This paper gives an overview about the Techniques related with "Generation of Virtual 3-D City models using Geomatics Techniques" and the Applications of Virtual 3D City models. Photogrammetry, (Close range, Aerial, Satellite), Lasergrammetry, GPS, or combination of these modern Geomatics techniques play a major role to create a virtual 3-D City model. Each and every techniques and method has some advantages and some drawbacks. Point cloud model is a modern trend for virtual 3-D city model. Photo-realistic, Scalable, Geo-referenced virtual 3

  20. Imidacloprid soil movement under micro-sprinkler irrigation and soil-drench applications to control Asian citrus psyllid (ACP) and citrus leafminer (CLM).

    Science.gov (United States)

    Fletcher, Evelyn; Morgan, Kelly T; Qureshi, Jawwad A; Leiva, Jorge A; Nkedi-Kizza, Peter

    2018-01-01

    Imidacloprid (IM) is used to control the Asian Citrus Psyllid (ACP) and citrus leafminer (CLM), which are related to the spread of huanglongbing (HLB or citrus greening) and citrus canker diseases, respectively. In Florida citrus, imidacloprid is mainly soil-drenched around the trees for proper root uptake and translocation into plant canopy to impact ACP and CLM. The objective of this study was to determine the effect of imidacloprid rate, and irrigate amount on concentration of imidacloprid in the soil following drench application to citrus trees in three age classes. The plots were established at the Southwest Florida Research and Education Center, Immokalee, using a randomized complete-block design for three age classes of trees: one-year-old trees (B1), three to five-year-old trees (B2), and eight-year-old trees (B3). The treatments were a combination of two rates each of imidacloprid (1D, 2D) and micro-sprinkling irrigation (1I, 2I). Imidacloprid and bromide (Br-) used as tracer were applied simultaneously. Soil moisture and concentrations of imidacloprid and Br were monitored using soil cores from hand held augers. Soil moisture content (θV) did not differ under two irrigation rates at any given observation day or depth, except following heavy rainfall events. Br- was lost from the observation depths (0-45 cm) about two weeks after soil-drench. Contrarily, imidacloprid persisted for a much longer time (4-8 weeks) at all soil depths, regardless of treatment combinations. The higher retardation of imidacloprid was related to the predominantly unsaturated conditions of the soil (which in turn reduced soil hydraulic conductivities by orders of magnitude), the imidacloprid sorption on soil organic matter, and the citrus root uptake. Findings of this study are important for citrus growers coping with the citrus greening and citrus canker diseases because they suggest that imidacloprid soil drenches can still be an effective control measure of ACP and CLM, and the

  1. MEMS-Based Power Generation Techniques for Implantable Biosensing Applications

    Directory of Open Access Journals (Sweden)

    Jonathan Lueke

    2011-01-01

    Full Text Available Implantable biosensing is attractive for both medical monitoring and diagnostic applications. It is possible to monitor phenomena such as physical loads on joints or implants, vital signs, or osseointegration in vivo and in real time. Microelectromechanical (MEMS-based generation techniques can allow for the autonomous operation of implantable biosensors by generating electrical power to replace or supplement existing battery-based power systems. By supplementing existing battery-based power systems for implantable biosensors, the operational lifetime of the sensor is increased. In addition, the potential for a greater amount of available power allows additional components to be added to the biosensing module, such as computational and wireless and components, improving functionality and performance of the biosensor. Photovoltaic, thermovoltaic, micro fuel cell, electrostatic, electromagnetic, and piezoelectric based generation schemes are evaluated in this paper for applicability for implantable biosensing. MEMS-based generation techniques that harvest ambient energy, such as vibration, are much better suited for implantable biosensing applications than fuel-based approaches, producing up to milliwatts of electrical power. High power density MEMS-based approaches, such as piezoelectric and electromagnetic schemes, allow for supplemental and replacement power schemes for biosensing applications to improve device capabilities and performance. In addition, this may allow for the biosensor to be further miniaturized, reducing the need for relatively large batteries with respect to device size. This would cause the implanted biosensor to be less invasive, increasing the quality of care received by the patient.

  2. MEMS-based power generation techniques for implantable biosensing applications.

    Science.gov (United States)

    Lueke, Jonathan; Moussa, Walied A

    2011-01-01

    Implantable biosensing is attractive for both medical monitoring and diagnostic applications. It is possible to monitor phenomena such as physical loads on joints or implants, vital signs, or osseointegration in vivo and in real time. Microelectromechanical (MEMS)-based generation techniques can allow for the autonomous operation of implantable biosensors by generating electrical power to replace or supplement existing battery-based power systems. By supplementing existing battery-based power systems for implantable biosensors, the operational lifetime of the sensor is increased. In addition, the potential for a greater amount of available power allows additional components to be added to the biosensing module, such as computational and wireless and components, improving functionality and performance of the biosensor. Photovoltaic, thermovoltaic, micro fuel cell, electrostatic, electromagnetic, and piezoelectric based generation schemes are evaluated in this paper for applicability for implantable biosensing. MEMS-based generation techniques that harvest ambient energy, such as vibration, are much better suited for implantable biosensing applications than fuel-based approaches, producing up to milliwatts of electrical power. High power density MEMS-based approaches, such as piezoelectric and electromagnetic schemes, allow for supplemental and replacement power schemes for biosensing applications to improve device capabilities and performance. In addition, this may allow for the biosensor to be further miniaturized, reducing the need for relatively large batteries with respect to device size. This would cause the implanted biosensor to be less invasive, increasing the quality of care received by the patient.

  3. Elements of slow-neutron scattering basics, techniques, and applications

    CERN Document Server

    Carpenter, J M

    2015-01-01

    Providing a comprehensive and up-to-date introduction to the theory and applications of slow-neutron scattering, this detailed book equips readers with the fundamental principles of neutron studies, including the background and evolving development of neutron sources, facility design, neutron scattering instrumentation and techniques, and applications in materials phenomena. Drawing on the authors' extensive experience in this field, this text explores the implications of slow-neutron research in greater depth and breadth than ever before in an accessible yet rigorous manner suitable for both students and researchers in the fields of physics, biology, and materials engineering. Through pedagogical examples and in-depth discussion, readers will be able to grasp the full scope of the field of neutron scattering, from theoretical background through to practical, scientific applications.

  4. Domain decomposition techniques for boundary elements application to fluid flow

    CERN Document Server

    Brebbia, C A; Skerget, L

    2007-01-01

    The sub-domain techniques in the BEM are nowadays finding its place in the toolbox of numerical modellers, especially when dealing with complex 3D problems. We see their main application in conjunction with the classical BEM approach, which is based on a single domain, when part of the domain needs to be solved using a single domain approach, the classical BEM, and part needs to be solved using a domain approach, BEM subdomain technique. This has usually been done in the past by coupling the BEM with the FEM, however, it is much more efficient to use a combination of the BEM and a BEM sub-domain technique. The advantage arises from the simplicity of coupling the single domain and multi-domain solutions, and from the fact that only one formulation needs to be developed, rather than two separate formulations based on different techniques. There are still possibilities for improving the BEM sub-domain techniques. However, considering the increased interest and research in this approach we believe that BEM sub-do...

  5. Scheduling of Irrigation and Leaching Requirements

    Directory of Open Access Journals (Sweden)

    Amer Hassan Al-haddad

    2015-03-01

    Full Text Available Iraq depends mainly on Tigris and Euphrates Rivers to provide high percentage of agricultural water use for thousands years. At last years, Iraq is suffering from shortage in water resources due to global climate changes and unfair water politics of the neighboring countries, which affected the future of agriculture plans for irrigation, added to that the lack of developed systems of water management in the irrigation projects and improper allocation of irrigation water, which reduces water use efficiency and lead to losing irrigation water and decreasing in agricultural yield. This study aims at studying the usability of irrigation and leaching scheduling within the irrigating projects and putting a complete annual or seasonal irrigation program as a solution for the scarcity of irrigation water, the increase of irrigation efficiency, lessening the salinity in the projects and preparing an integral irrigation calendar through field measurements of soil physical properties and chemical for project selected and compared to the results of the irrigation scheduling and leaching with what is proposed by the designers. The process is accomplished by using a computer program which was designed by Water Resources Department at the University of Baghdad, with some modification to generalize it and made it applicable to various climatic zone and different soil types. Study area represented by large project located at the Tigris River, and this project was (Al-Amara irrigation project. Sufficient samples of project's soil were collected so as to identify soil physical and chemical properties and the salinity of soil and water as well as identifying the agrarian cycles virtually applied to this project. Finally, a comparison was conducted between the calculated water quantities and the suggested ones by the designers. The research results showed that using this kind of scheduling (previously prepared irrigation and leaching scheduling with its properties

  6. Effects of irrigation strategies and soils on field grown potatoes

    DEFF Research Database (Denmark)

    Ahmadi, Seyed Hamid; Plauborg, Finn; Andersen, Mathias Neumann

    2011-01-01

    Root distribution of field grown potatoes (cv. Folva) was studied in 4.32m2 lysimeters and subjected to full (FI), deficit (DI), and partial root-zone drying (PRD) irrigation strategies. Drip irrigation was applied for all irrigations. Irrigations were run in three different soils: coarse sand......, loamy sand, and sandy loam. Irrigation treatments started after tuber bulking and lasted until final harvest with PRD and DI receiving 65% of FI. Potatoes irrigated with water-saving irrigation techniques (PRD and DI) did not show statistically different dry root mass and root length density (RLD, cm...... density in the furrow. Most roots accumulated in the surface layers of coarse sand as compared to the other soil types. In the deep soil profile (30–70 cm) a higher root density was found in loamy sand compared with the sandy loam and coarse sand. Approximately twice the amounts of roots were found below...

  7. APPLICABILITY OF COOPERATIVE LEARNING TECHNIQUES IN DIFFERENT CLASSROOM CONTEXTS

    Directory of Open Access Journals (Sweden)

    Dr. Issy Yuliasri

    2017-04-01

    Full Text Available This paper is based on the results of pre-test post-test, feedback questionnaire and observation during a community service program entitled ―Training on English Teaching using Cooperative Learning Techniques for Elementary and Junior High School Teachers of Sekolah Alam Arridho Semarang‖. It was an English teaching training program intended to equip the teachers with the knowledge and skills of using the different cooperative learning techniques such as jigsaw, think-pair-share, three-step interview, roundrobin braistorming, three-minute review, numbered heads together, team-pair-solo, circle the sage, dan partners. This program was participated by 8 teachers of different subjects (not only English, but most of them had good mastery of English. The objectives of this program was to improve teachers‘ skills in using the different cooperative learning techniques to vary their teaching, so that students would be more motivated to learn and improve their English skill. Besides, the training also gave the teachers the knowledge and skills to adjust their techniques with the basic competence and learning objectives to be achieved as well as with the teaching materials to be used. This was also done through workshops using cooperative learning techniques, so that the participants had real experiences of using cooperative learning techniques (learning by doing. The participants were also encouraged to explore the applicability of the techniques in their classroom contexts, in different areas of their teaching. This community service program showed very positive results. The pre-test and post-test results showed that before the training program all the participants did not know the nine cooperative techniques to be trained, but after the program they mastered the techniques as shown from the teaching-learning scenarios they developed following the test instructions. In addition, the anonymous questionnaires showed that all the participants

  8. A German research project about applicable graphite cutting techniques

    International Nuclear Information System (INIS)

    Holland, D.; Quade, U.; Bach, F.W.; Wilk, P.

    2001-01-01

    In Germany, too, quite large quantities of irradiated nuclear graphite, used in research and prototype reactors, are waiting for an environmental way of disposal. While incineration of nuclear graphite does not seem to be a publicly acceptable way, cutting and packaging into ductile cast iron containers could be a suitable way of disposal in Germany. Nevertheless, the cutting of graphite is also a very difficult technique by which a large amount of secondary waste or dust might occur. An applicable graphite cutting technique is needed. Therefore, a group of 13 German partners, consisting of one university, six research reactor operators, one technical inspection authority, three engineering companies, one industrial cutting specialist and one commercial dismantling company, decided in 1999 to start a research project to develop an applicable technique for cutting irradiated nuclear graphite. Aim of the project is to find the most suitable cutting techniques for the existing shapes of graphite blocks with a minimum of waste production rate. At the same time it will be learned how to sample the dust and collect it in a filter system. The following techniques will be tested and evaluated: thermal cutting, water jet cutting, mechanical cutting with a saw, plasma arc cutting, drilling. The subsequent evaluation will concentrate on dust production, possible irradiation of staff, time and practicability under different constraints. This research project is funded by the German Minister of Education and Research under the number 02 S 7849 for a period of two years. A brief overview about the work to be carried out in the project will be given. (author)

  9. Development of Plant Application Technique of Low Dose Radiation

    Energy Technology Data Exchange (ETDEWEB)

    Chung, Byung Yeoup; Kim, Jae Sung; Lim, Yong Taek (and others)

    2007-07-15

    The project was carried out to achieve three aims. First, development of application techniques of cell-stimulating effects by low-dose radiation. Following irradiation with gamma-rays of low doses, beneficial effects in crop germination, early growth, and yield were investigated using various plant species and experimental approaches. For the actual field application, corroborative studies were also carried out with a few concerned experimental stations and farmers. Moreover, we attempted to establish a new technique of cell cultivation for industrial mass-production of shikonin, a medicinal compound from Lithospermum erythrorhizon and thereby suggested new application fields for application techniques of low-dose radiation. Second, elucidation of action mechanisms of ionizing radiation in plants. By investigating changes in plant photosynthesis and physiological metabolism, we attempted to elucidate physiological activity-stimulating effects of low-dose radiation and to search for radiation-adaptive cellular components. Besides, analyses of biochemical and molecular biological mechanisms for stimulus-stimulating effects of low-dose radiation were accomplished by examining genes and proteins inducible by low-dose radiation. Third, development of functional crop plants using radiation-resistant factors. Changes in stress-tolerance of plants against environmental stress factors such as light, temperature, salinity and UV-B stress after exposed to low-dose gamma-rays were investigated. Concerned reactive oxygen species, antioxidative enzymes, and antioxidants were also analyzed to develop high value-added and environment-friendly functional plants using radiation-resistant factors. These researches are important to elucidate biological activities increased by low-dose radiation and help to provide leading technologies for improvement of domestic productivity in agriculture and development of high value-added genetic resources.

  10. Development of Plant Application Technique of Low Dose Radiation

    International Nuclear Information System (INIS)

    Chung, Byung Yeoup; Kim, Jae Sung; Lim, Yong Taek

    2007-07-01

    The project was carried out to achieve three aims. First, development of application techniques of cell-stimulating effects by low-dose radiation. Following irradiation with gamma-rays of low doses, beneficial effects in crop germination, early growth, and yield were investigated using various plant species and experimental approaches. For the actual field application, corroborative studies were also carried out with a few concerned experimental stations and farmers. Moreover, we attempted to establish a new technique of cell cultivation for industrial mass-production of shikonin, a medicinal compound from Lithospermum erythrorhizon and thereby suggested new application fields for application techniques of low-dose radiation. Second, elucidation of action mechanisms of ionizing radiation in plants. By investigating changes in plant photosynthesis and physiological metabolism, we attempted to elucidate physiological activity-stimulating effects of low-dose radiation and to search for radiation-adaptive cellular components. Besides, analyses of biochemical and molecular biological mechanisms for stimulus-stimulating effects of low-dose radiation were accomplished by examining genes and proteins inducible by low-dose radiation. Third, development of functional crop plants using radiation-resistant factors. Changes in stress-tolerance of plants against environmental stress factors such as light, temperature, salinity and UV-B stress after exposed to low-dose gamma-rays were investigated. Concerned reactive oxygen species, antioxidative enzymes, and antioxidants were also analyzed to develop high value-added and environment-friendly functional plants using radiation-resistant factors. These researches are important to elucidate biological activities increased by low-dose radiation and help to provide leading technologies for improvement of domestic productivity in agriculture and development of high value-added genetic resources

  11. Application of remote sensing techniques for conserving scarce water resources: a case study from Pakistan

    International Nuclear Information System (INIS)

    Shakoor, A; Alam, N; Asghar, M.N.

    2005-01-01

    Pakistan, which was once a water surplus, is now a water deficit country according to Malin Falkenmark criteria. The conventional wisdom of managing canal water supplies, which usually results in over- or under-irrigation, is not sufficient to meet the challenge of water demand in future. This paper introduces the use of modem tools like Remote Sensing (RS), Geographic Information Systems (GIS) and CROPWAT to improve the management of the existing irrigation systems. This study was conducted for the Pehure High Level Canal (PHLC) and the Upper Swat Canal (USC) system in the North Western Frontier Province (NWFP) of Pakistan. Crop identification at distributary level was made from multi-temporal Remote Sensing satellite images, using various image processing techniques, such as supervised, unsupervised classification and spectral mixture analysis. Cropped areas were calculated for each individual crop from these classified images, and then crop water requirement at distributary level was estimated using CROPWAT. Assuming all other parameters of the CROPWAT model optimistic, the calculated crop area was of major concern. The supervised classification with support of unsupervised classification and ground truth information has proven to be the best option and cost-effective technique for calculating the actual cropped area. The results of this study can be used while devising guidelines for water managers to release the canal supplies based, on crop water requirement. This practice will help in avoiding wastage of canal water at farm level, which can be optimally used for increasing irrigated areas and crop productivity in the area. (author)

  12. Conference on Nuclear and Conventional Analytical Techniques and their Applications

    International Nuclear Information System (INIS)

    2010-01-01

    Full text : A panoply analytic techniques methods has emerged in recent decades due to the challenges of society in quality of products and the increasing demand of chemical analysis services. The industrial progress which came along with an instrumental perfection of devices with analytical use, led to the development of new techniques more and more advanced in this field. These come as well, to answer the disturbing effects of this industrialization and the wishes of a public increasingly conscious and requiring globally. The leaders in this field of analysis and material characterization are more than ever confronted with problems of identification and quantification of different chemical forms of a multitude of products in varied circles; Industrial pollutants, soil, water, air, food, medicines, ceramics, concrete, plants etc. It was from that perspective that the unifying theme ''geomaterials: characterization to applications '' of the conference on nuclear and conventional analytical techniques and their applications (TANCA 2010) was chosen. It contributes to the debate of these subjects and builds relationships between stakeholders in this field, both technically and practically [fr

  13. Application of Artificial Intelligence Techniques in Unmanned Aerial Vehicle Flight

    Science.gov (United States)

    Bauer, Frank H. (Technical Monitor); Dufrene, Warren R., Jr.

    2003-01-01

    This paper describes the development of an application of Artificial Intelligence for Unmanned Aerial Vehicle (UAV) control. The project was done as part of the requirements for a class in Artificial Intelligence (AI) at Nova southeastern University and as an adjunct to a project at NASA Goddard Space Flight Center's Wallops Flight Facility for a resilient, robust, and intelligent UAV flight control system. A method is outlined which allows a base level application for applying an AI method, Fuzzy Logic, to aspects of Control Logic for UAV flight. One element of UAV flight, automated altitude hold, has been implemented and preliminary results displayed. A low cost approach was taken using freeware, gnu, software, and demo programs. The focus of this research has been to outline some of the AI techniques used for UAV flight control and discuss some of the tools used to apply AI techniques. The intent is to succeed with the implementation of applying AI techniques to actually control different aspects of the flight of an UAV.

  14. Armenia - Irrigation Infrastructure

    Data.gov (United States)

    Millennium Challenge Corporation — This study evaluates irrigation infrastructure rehabilitation in Armenia. The study separately examines the impacts of tertiary canals and other large infrastructure...

  15. Application perspectives of simulation techniques CFD in nuclear power plants

    International Nuclear Information System (INIS)

    Galindo G, I. F.

    2013-10-01

    The scenarios simulation in nuclear power plants is usually carried out with system codes that are based on concentrated parameters networks. However situations exist in some components where the flow is predominantly 3-D, as they are the natural circulation, mixed and stratification phenomena. The simulation techniques of computational fluid dynamics (CFD) have the potential to simulate these flows numerically. The use of CFD simulations embraces many branches of the engineering and continues growing, however, in relation to its application with respect to the problems related with the safety in nuclear power plants, has a smaller development, although is accelerating quickly and is expected that in the future they play a more emphasized paper in the analyses. A main obstacle to be able to achieve a general acceptance of the CFD is that the simulations should have very complete validation studies, sometimes not available. In this article a general panorama of the state of the methods application CFD in nuclear power plants is presented and the problem associated to its routine application and acceptance, including the view point of the regulatory authorities. Application examples are revised in those that the CFD offers real benefits and are also presented two illustrative study cases of the application of CFD techniques. The case of a water recipient with a heat source in its interior, similar to spent fuel pool of a nuclear power plant is presented firstly; and later the case of the Boron dilution of a water volume that enters to a nuclear reactor is presented. We can conclude that the CFD technology represents a very important opportunity to improve the phenomena understanding with a strong component 3-D and to contribute in the uncertainty reduction. (Author)

  16. Evaluation of best management practices under intensive irrigation using SWAT model

    OpenAIRE

    Dechmi, Farida; Skhiri, Ahmed

    2013-01-01

    Land management practices such as conservation tillage and optimum irrigation are routinely used to reduce non-point source pollution and improve water quality. The calibrated and validated SWAT-IRRIG model is the first modified SWAT version that reproduces well the irrigation return flows (IRF) when the irrigation source is outside of the watershed. The application of this SWAT version in intensive irrigated systems permits to better evaluate the best management practices (BMPs) in such syst...

  17. Innovative SU-8 Lithography Techniques and Their Applications

    Directory of Open Access Journals (Sweden)

    Jeong Bong Lee

    2014-12-01

    Full Text Available SU-8 has been widely used in a variety of applications for creating structures in micro-scale as well as sub-micron scales for more than 15 years. One of the most common structures made of SU-8 is tall (up to millimeters high-aspect-ratio (up to 100:1 3D microstructure, which is far better than that made of any other photoresists. There has been a great deal of efforts in developing innovative unconventional lithography techniques to fully utilize the thick high aspect ratio nature of the SU-8 photoresist. Those unconventional lithography techniques include inclined ultraviolet (UV exposure, back-side UV exposure, drawing lithography, and moving-mask UV lithography. In addition, since SU-8 is a negative-tone photoresist, it has been a popular choice of material for multiple-photon interference lithography for the periodic structure in scales down to deep sub-microns such as photonic crystals. These innovative lithography techniques for SU-8 have led to a lot of unprecedented capabilities for creating unique micro- and nano-structures. This paper reviews such innovative lithography techniques developed in the past 15 years or so.

  18. Precision overhead irrigation is suitable for several Central Valley crops

    Directory of Open Access Journals (Sweden)

    Jeffrey P. Mitchell

    2016-04-01

    Full Text Available Overhead systems are the dominant irrigation technology in many parts of the world, but they are not widely used in California even though they have higher water application efficiency than furrow irrigation systems and lower labor requirements than drip systems. With water and labor perennial concerns in California, the suitability of overhead systems merits consideration. From 2008 through 2013, in studies near Five Points, California, we evaluated overhead irrigation for wheat, corn, cotton, tomato, onion and broccoli as an alternative to furrow and drip irrigation. With the exception of tomato, equal or increased yields were achieved with overhead irrigation. Many variables are involved in the choice of an irrigation system, but our results suggest that, with more research to support best management practices, overhead irrigation may be useful to a wider set of California farmers than currently use it.

  19. Sensitivity analysis technique for application to deterministic models

    International Nuclear Information System (INIS)

    Ishigami, T.; Cazzoli, E.; Khatib-Rahbar, M.; Unwin, S.D.

    1987-01-01

    The characterization of sever accident source terms for light water reactors should include consideration of uncertainties. An important element of any uncertainty analysis is an evaluation of the sensitivity of the output probability distributions reflecting source term uncertainties to assumptions regarding the input probability distributions. Historically, response surface methods (RSMs) were developed to replace physical models using, for example, regression techniques, with simplified models for example, regression techniques, with simplified models for extensive calculations. The purpose of this paper is to present a new method for sensitivity analysis that does not utilize RSM, but instead relies directly on the results obtained from the original computer code calculations. The merits of this approach are demonstrated by application of the proposed method to the suppression pool aerosol removal code (SPARC), and the results are compared with those obtained by sensitivity analysis with (a) the code itself, (b) a regression model, and (c) Iman's method

  20. Artificial magma and applications of the blasting technique

    Energy Technology Data Exchange (ETDEWEB)

    Ichioka, K [Chugoku Kaki KK, Japan

    1974-01-01

    Artifical magma is discussed. Solid magma is a high temperature source and fluid magma is also a heat carrier. Iron ores are examples of solid magma, silica-borate is an example of a hydrophobic heat carrier magma assuming a liquid phase at 600/sup 0/C, and S, Ag, Pb, etc. are also examples of heat carrier magma. In addition to these examples, basic salts such as NaNO/sub 3/, KNO/sub 3/, NaCl, CaCl, KCl, BaCl, and Na/sub 4/B/sub 4/O/sub 7/ can be used as artifical magma. These are artifical magmas or heat mediums capable of capturing geothermal heat when circulated inside volcanoes. The blasting technique's applications in geothermal wells are also discussed. The technique can be used to expand a well's diameter, repair the well bottom, regenerate old wells, clean wells, or cut steel pipe. Two figures and one table are provided.

  1. Positron lifetime technique with applications in materials science

    International Nuclear Information System (INIS)

    Vries, J. de.

    1987-01-01

    This thesis deals with the positron lifetime technique as a method to measure extremely low concentrations of extremely small cavities in materials. The method is based upon the fact that the positron lieftime decreases as the electron density increases and upon the fact that a positron preferably annihilates in cavity-like defects in lattices. The theory of positron behaviour in materials and technical aspects of measuring positron liefetimes are described in ch.'s 2 and 3 respectively. Three methods for increasing the time resolution are discussed and some positron sources are described (ch.4). Some applications of the positron lifetime technique and experimental results are shown in chapter 5. 125 refs.; 61 figs.; 18 tabs

  2. Nuclear analytical techniques and their application to environmental samples

    International Nuclear Information System (INIS)

    Lieser, K.H.

    1986-01-01

    A survey is given on nuclear analytical techniques and their application to environmental samples. Measurement of the inherent radioactivity of elements or radionuclides allows determination of natural radioelements (e.g. Ra), man-made radioelements (e.g. Pu) and radionuclides in the environment. Activation analysis, in particular instrumental neutron activation analysis, is a very reliable and sensitive method for determination of a great number of trace elements in environmental samples, because the most abundant main constituents are not activated. Tracer techniques are very useful for studies of the behaviour and of chemical reactions of trace elements and compounds in the environment. Radioactive sources are mainly applied for excitation of characteristic X-rays (X-ray fluorescence analysis). (author)

  3. Concerning the application of the nuclear and related techniques

    International Nuclear Information System (INIS)

    Desdin Garcia, Luis Felipe

    1997-01-01

    The present work intends to describe briefly, some of the nuclear and connected techniques of greater application in the conditions of developing countries, which are employed in the Center of Studies Applied to the Nuclear Development, and that can be of interest for the Latin-American countries. Within those techniques we have: radiobiology, that consists of the employment of ionizing radiations to induce mutations oriented to the improvement of the cultivations. It mentions the atmospheric contamination generated by the industry of the exposition to metals and toxic waste, and of mortiferous parasites that adapt quickly to the unhealthy environmental conditions. It also enumerates some advantages of the utilization of instruments based on radioisotopic fountains. (S. Grainger) [es

  4. Recent applications of nuclear medicine techniques and results in Vietnam

    International Nuclear Information System (INIS)

    Phan Sy An

    2008-01-01

    The author presented recent applications of nuclear medicine techniques and results in Vietnam. The author concentrated some valuable and helpful studies such as functional tests, myocardial perfusion scintigraphy, bone, thyroid, lung, kidney and gastrointestinal tract scintigraphy for diagnosis. The results of RIA and IRMA concerning with thyroid diseases, cancer, microalbuminuria and TSH in blood spot on paper for screening of congenital hypothyroidism in new born babies were also given. The report also mentioned results of liver cancer and palliative bone metastasis treatments in Vietnam. A new technique using gamma probe in surgery for breast cancer was presented. The author introduced some modern teleradiotherapeutic modalities such as cyberknif, gamma knife, gamma rotating systeme and linac recently installed in Vietnam. (author)

  5. The application of value analysis techniques for complex problems

    International Nuclear Information System (INIS)

    Chiquelin, W.R.; Cossel, S.C.; De Jong, V.J.; Halverson, T.W.

    1986-01-01

    This paper discusses the application of the Value Analysis technique to the transuranic package transporter (TRUPACT). A team representing five different companies or organizations with diverse technical backgrounds was formed to analyze and recommend improvements. The results were a 38% systems-wide savings, if incorporated, and a shipping container which is volumetrically and payload efficient as well as user friendly. The Value Analysis technique is a proven tool widely used in many diverse areas both in the government and the private sector. Value Analysis uses functional diagramming of a piece of equipment or process to discretely identify every facet of the item being analyzed. A standard set of questions is then asked: What is it?, What does it do?, What does it cost?, What else will do the task?, and What would that cost? Using logic and a disciplined approach, the result of the Value Analysis performs the necessary functions at a high quality and the lowest overall cost

  6. Decomposition techniques in mathematical programming engineering and science applications

    CERN Document Server

    Conejo, Antonio J; Minguez, Roberto; Garcia-Bertrand, Raquel

    2006-01-01

    Optimization plainly dominates the design, planning, operation, and c- trol of engineering systems. This is a book on optimization that considers particular cases of optimization problems, those with a decomposable str- ture that can be advantageously exploited. Those decomposable optimization problems are ubiquitous in engineering and science applications. The book considers problems with both complicating constraints and complicating va- ables, and analyzes linear and nonlinear problems, with and without in- ger variables. The decomposition techniques analyzed include Dantzig-Wolfe, Benders, Lagrangian relaxation, Augmented Lagrangian decomposition, and others. Heuristic techniques are also considered. Additionally, a comprehensive sensitivity analysis for characterizing the solution of optimization problems is carried out. This material is particularly novel and of high practical interest. This book is built based on many clarifying, illustrative, and compu- tional examples, which facilitate the learning p...

  7. Techniques For Microfabricating Coils For Microelectromechanical Systems Applications

    International Nuclear Information System (INIS)

    Woods, R. C.; Powell, A. L.

    2008-01-01

    The advanced technology necessary for building future space exploration vehicles includes microfabricated coils for making possible self-inductances integrated with other passive and active electronic components. Integrated inductances make possible significant improvements in reliability over the traditional arrangement of using external discrete inductances, as well as allowing significant size (volume) reductions (also important in space vehicles). Two possible fabrication techniques (one using proprietary branded 'Foturan' glass, the other using silicon wafer substrates) for microscopic coils are proposed, using electroplating into channels. The techniques have been evaluated for fabricating the planar electrical coils needed for typical microelectromechanical systems applications. There remain problems associated with processing using 'Foturan' glass, but coil fabrication on silicon wafers was successful. Fabrication methods such as these are expected to play an important part in the development of systems and subsystems for forthcoming space exploration missions

  8. Application of DSSAT-CROPGRO-Cotton Model to Assess Long Term (1924-2012) Cotton Yield under Different Irrigation Management Strategies

    Science.gov (United States)

    Adhikari, P.; Gowda, P. H.; Northup, B. K.; Rocateli, A.

    2017-12-01

    In this study a well calibrated and validated DSSAT-CROPGRO-Cotton model was used for assessing the irrigation management in the Texas High Plains (THP). Long term (1924-2012) historic lint yield were simulated under different irrigation management practices which were commonly used in the THP. The simulation treatments includes different amount of irrigation water high (H; 6.4 mm d-1), medium (M; 3.2 mm d-1) and low (L; 0 mm d-1) during emergence (S1), vegetative (S2) and maturity (S3) stage. The combination of these treatments resulted into 27 treatments. The amount and date of irrigation for each stage were obtained from the recent cotton irrigation experiment at Halfway, TX (Brodovsky, et al., 2015). Similarly, calibrated model was also used to observe the effect of plantation date on crop yield in the THP regions.

  9. Irrigation Water Management in Latin America

    Directory of Open Access Journals (Sweden)

    Aureo S de Oliveira

    2009-12-01

    Full Text Available Latin American countries show a great potential for expanding their irrigated areas. Irrigation is important for strengthening local and regional economy and for enhancing food security. The present paper aimed at providing a brief review on key aspects of irrigation management in Latin America. Poor irrigation management can have great impact on crop production and on environment while good management reduces the waste of soil and water and help farmers maximizing their profits. It was found that additional research is needed to allow a better understanding of crop water requirements under Latin American conditions as well as to provide farmers with local derived information for irrigation scheduling. The advantages of deficit irrigation practices and the present and future opportunities with the application of remote sensing tools for water management were also considered. It is clear that due to the importance of irrigated agriculture, collaborative work among Latin American researchers and institutions is of paramount importance to face the challenges imposed by a growing population, environment degradation, and competition in the global market.

  10. Application of positron annihilation technique to reverse osmosis membrane materials

    International Nuclear Information System (INIS)

    Shimazu, A.; Ikeda, K.; Miyazaki, T.; Ito, Y.

    2000-01-01

    Positron annihilation lifetime spectroscopy has been adopted as a new approach for studying vacancies of reverse osmosis membrane materials composed of cellulose acetate films and aromatic polyamide resins. The intensity of the ortho-positronium (o-Ps) lifetime increased with the amount of vacancies determined using N 2 isotherm at -195 deg. C. Changes of vacancy profiles induced by heat treatment in the cellulose acetate films were detected using o-Ps. It was found that the positron annihilation technique is applicable to the study of vacancy profiles associated with salt selectivity in typical reverse osmosis membranes.

  11. Application of Nuclear Techniques in Industry and the Environment

    International Nuclear Information System (INIS)

    Masinza, A.S.

    2015-01-01

    Major radiotracer techniques are now in routine service industry to optimize processes, solve problems improve product quality, save energy and reduction pollution. The benefit to cost ratios of radiotracers, sealed sources and nucleonic gauges applications are considerably high; between 10:1 and 4000:1. The number of services for troubleshooting carried out worldwide per year is in excess of tens of thousands (out of them greater than 5000 are gamma scans). The number of nucleonic gauges worldwide could be estimated to be greater that 250,000 (Author)

  12. The application of radiotracer technique for preconcentration neutron activation analysis

    International Nuclear Information System (INIS)

    Wang Xiaolin; Chen Yinliang; Sun Ying; Fu Yibei

    1995-01-01

    The application of radiotracer technique for preconcentration neutron activation analysis (Pre-NAA) are studied and the method for determination of chemical yield of Pre-NAA is developed. This method has been applied to determination of gold, iridium and rhenium in steel and rock samples and the contents of noble metal are in the range of 1-20 ng·g -1 (sample). In addition, the accuracy difference caused by determination of chemical yield between RNAA and Pre-NAA are also discussed

  13. [Advances of Molecular Diagnostic Techniques Application in Clinical Diagnosis.

    Science.gov (United States)

    Ying, Bin-Wu

    2016-11-01

    Over the past 20 years,clinical molecular diagnostic technology has made rapid development,and became the most promising field in clinical laboratory medicine.In particular,with the development of genomics,clinical molecular diagnostic methods will reveal the nature of clinical diseases in a deeper level,thus guiding the clinical diagnosis and treatments.Many molecular diagnostic projects have been routinely applied in clinical works.This paper reviews the advances on application of clinical diagnostic techniques in infectious disease,tumor and genetic disorders,including nucleic acid amplification,biochip,next-generation sequencing,and automation molecular system,and so on.

  14. Application of stereo photogrammetric techniques for measuring African Elephants

    Directory of Open Access Journals (Sweden)

    A. J Hall-Martin

    1979-12-01

    Full Text Available Measurements of shoulder height and back length of African elephants were obtained by means of stereo photogrammetric techniques. A pair of Zeiss UMK 10/1318 cameras, mounted on a steel frame on the back of a vehicle, were used to photograph the elephants in the Addo Elephant National Park, Republic of South Africa. Several modifications of normal photogrammetry procedure applicable to the field situation (eg. control points and the computation of results (eg. relative orientation are briefly mentioned. Six elephants were immobilised after being photographed and the measurements obtained from them agreed within a range of 1 cm-10 cm with the photogrammetric measurements.

  15. Pulsed electrical discharges for medicine and biology techniques, processes, applications

    CERN Document Server

    Kolikov, Victor

    2015-01-01

    This book presents the application of pulsed electrical discharges in water and water dispersions of metal nanoparticles in medicine (surgery, dentistry, and oncology), biology, and ecology. The intensive electrical and shock waves represent a novel technique to destroy viruses and this way to  prepare anti-virus vaccines. The method of pulsed electrical discharges in water allows to decontaminate water from almost all known bacteria and spores of fungi being present in human beings. The nanoparticles used are not genotoxic and mutagenic. This book is useful for researchers and graduate students.

  16. APPLICATION OF OBJECT ORIENTED PROGRAMMING TECHNIQUES IN FRONT END COMPUTERS

    International Nuclear Information System (INIS)

    SKELLY, J.F.

    1997-01-01

    The Front End Computer (FEC) environment imposes special demands on software, beyond real time performance and robustness. FEC software must manage a diverse inventory of devices with individualistic timing requirements and hardware interfaces. It must implement network services which export device access to the control system at large, interpreting a uniform network communications protocol into the specific control requirements of the individual devices. Object oriented languages provide programming techniques which neatly address these challenges, and also offer benefits in terms of maintainability and flexibility. Applications are discussed which exhibit the use of inheritance, multiple inheritance and inheritance trees, and polymorphism to address the needs of FEC software

  17. Application of object modeling technique to medical image retrieval system

    International Nuclear Information System (INIS)

    Teshima, Fumiaki; Abe, Takeshi

    1993-01-01

    This report describes the results of discussions on the object-oriented analysis methodology, which is one of the object-oriented paradigms. In particular, we considered application of the object modeling technique (OMT) to the analysis of a medical image retrieval system. The object-oriented methodology places emphasis on the construction of an abstract model from real-world entities. The effectiveness of and future improvements to OMT are discussed from the standpoint of the system's expandability. These discussions have elucidated that the methodology is sufficiently well-organized and practical to be applied to commercial products, provided that it is applied to the appropriate problem domain. (author)

  18. Application of adaptive antenna techniques to future commercial satellite communication

    Science.gov (United States)

    Ersoy, L.; Lee, E. A.; Matthews, E. W.

    1987-01-01

    The purpose of this contract was to identify the application of adaptive antenna technique in future operational commercial satellite communication systems and to quantify potential benefits. The contract consisted of two major subtasks. Task 1, Assessment of Future Commercial Satellite System Requirements, was generally referred to as the Adaptive section. Task 2 dealt with Pointing Error Compensation Study for a Multiple Scanning/Fixed Spot Beam Reflector Antenna System and was referred to as the reconfigurable system. Each of these tasks was further sub-divided into smaller subtasks. It should also be noted that the reconfigurable system is usually defined as an open-loop system while the adaptive system is a closed-loop system. The differences between the open- and closed-loop systems were defined. Both the adaptive and reconfigurable systems were explained and the potential applications of such systems were presented in the context of commercial communication satellite systems.

  19. Digital holography and wavefront sensing principles, techniques and applications

    CERN Document Server

    Schnars, Ulf; Watson, John; Jüptner, Werner

    2015-01-01

    This book presents a self-contained treatment of the principles and major applications of digital hologram recording and numerical reconstruction (Digital Holography). This second edition has been significantly revised and enlarged. The authors have extended the chapter on Digital Holographic Microscopy to incorporate new sections on particle sizing, particle image velocimetry and underwater holography. A new chapter now deals comprehensively and extensively with computational wave field sensing. These techniques represent a fascinating alternative to standard interferometry and Digital Holography. They enable wave field sensing without the requirement of a particular reference wave, thus allowing the use of low brilliance light sources and even liquid-crystal displays (LCD) for interferometric applications.              

  20. New approaches in intelligent control techniques, methodologies and applications

    CERN Document Server

    Kountchev, Roumen

    2016-01-01

    This volume introduces new approaches in intelligent control area from both the viewpoints of theory and application. It consists of eleven contributions by prominent authors from all over the world and an introductory chapter. This volume is strongly connected to another volume entitled "New Approaches in Intelligent Image Analysis" (Eds. Roumen Kountchev and Kazumi Nakamatsu). The chapters of this volume are self-contained and include summary, conclusion and future works. Some of the chapters introduce specific case studies of various intelligent control systems and others focus on intelligent theory based control techniques with applications. A remarkable specificity of this volume is that three chapters are dealing with intelligent control based on paraconsistent logics.

  1. Movement of Irrigation Water in Soil from a Surface Emitter

    Directory of Open Access Journals (Sweden)

    Ibrahim Abbas Dawood

    2016-09-01

    Full Text Available rickle irrigation is one of the most conservative irrigation techniques since it implies supplying water directly on the soil through emitters. Emitters dissipate energy of water at the end of the trickle irrigation system and provide water at emission points. The area wetted by an emitter depends upon the discharge of emitter, soil texture, initial soil water content, and soil permeability. The objectives of this research were to predict water distribution profiles through different soils for different conditions and quantify the distribution profiles in terms of main characteristics of soil and emitter. The wetting patterns were simulated at the end of each hour for a total time of application of 12 hrs, emitter discharges of 0.5, 0.75, 1, 2, 3, 4, and 5 lph, and five initial volumetric soil water contents. Simulation of water flow from a single surface emitter was carried out by using the numerically-based software Hydrus-2D/3D, Version 2.04. Two approaches were used in developing formulas to predict the domains of the wetted pattern. In order to verify the results obtained by implementing the software Hydrus-2D/3D a field experiment was conducted to measure the wetted diameter and compare measured values with simulated ones. The results of the research showed that the developed formulas to express the wetted diameter and depth in terms of emitter discharge, time of application, and initial soil water content are very general and can be used with very good accuracy.

  2. Applying advanced digital signal processing techniques in industrial radioisotopes applications

    International Nuclear Information System (INIS)

    Mahmoud, H.K.A.E.

    2012-01-01

    Radioisotopes can be used to obtain signals or images in order to recognize the information inside the industrial systems. The main problems of using these techniques are the difficulty of identification of the obtained signals or images and the requirement of skilled experts for the interpretation process of the output data of these applications. Now, the interpretation of the output data from these applications is performed mainly manually, depending heavily on the skills and the experience of trained operators. This process is time consuming and the results typically suffer from inconsistency and errors. The objective of the thesis is to apply the advanced digital signal processing techniques for improving the treatment and the interpretation of the output data from the different Industrial Radioisotopes Applications (IRA). This thesis focuses on two IRA; the Residence Time Distribution (RTD) measurement and the defect inspection of welded pipes using a gamma source (gamma radiography). In RTD measurement application, this thesis presents methods for signal pre-processing and modeling of the RTD signals. Simulation results have been presented for two case studies. The first case study is a laboratory experiment for measuring the RTD in a water flow rig. The second case study is an experiment for measuring the RTD in a phosphate production unit. The thesis proposes an approach for RTD signal identification in the presence of noise. In this approach, after signal processing, the Mel Frequency Cepstral Coefficients (MFCCs) and polynomial coefficients are extracted from the processed signal or from one of its transforms. The Discrete Wavelet Transform (DWT), Discrete Cosine Transform (DCT), and Discrete Sine Transform (DST) have been tested and compared for efficient feature extraction. Neural networks have been used for matching of the extracted features. Furthermore, the Power Density Spectrum (PDS) of the RTD signal has been also used instead of the discrete

  3. Some essential techniques for developing efficient petascale applications

    International Nuclear Information System (INIS)

    Kale, L V

    2008-01-01

    Multiple petaflops-lass machines will appear during the coming year, and many multipetaflops machines are on the anvil. It will be a substantial challenge to make existing parallel CSE applications run efficiently on them, and even more challenging to design new applications that can effectively leverage the large computational power of these machines. Multicore chips and SMP nodes are becoming popular and pose challenges of their own. Further, a new set of challenges in productivity arise, especially if we wish to have a broader set of applications and people to use these machines. Reviewed here is a set of techniques that have proved useful in multiple parallel applications that have scaled to tens of thousands of processors, on machines such as the Blue Gene/L, Blue Gene/P, Cray XT3, and XT4. New challenges and potential solutions for the performance issues are identified. Issues presented by multicore chips and SMP nodes also rre addressed. Also reviewed are some new and old ideas for increasing productivity in parallel programming substantially

  4. Analysis of energy requirement in the irrigation sector and its application in groundwater over-pumping control at a local scale - A case study in the North China Plain

    Science.gov (United States)

    Wang, L.; Kinzelbach, W.; Yao, H.; Hagmann, A.; Li, N.; Steiner, J. F.

    2017-12-01

    The North China Plain is one of the most important agricultural regions which relies heavily on groundwater pumping for irrigation powered by electric energy. This region is also facing a severe problem of groundwater over-pumping. Stopping groundwater depletion by controlling pumping for irrigation may harm the agricultural production and affect the interests of the electricity utility who is a direct participant in the irrigation management. Water-saving infrastructures such as sprinklers can be effective means for water conservation but are often difficult to implement due to farmers' unwillingness to pay for the additional electricity consumption. Understanding this food-energy-water nexus is fundamental to implement effective and practical strategies for groundwater over-pumping control in the North China Plain. However, this understanding can be obscured by the missing groundwater pumping monitoring and a lack of access to specific energy data for irrigation use as well as the field observations of pump efficiency. Taking the example of a typical agricultural county (Guantao) in the North China Plain with irrigation pumps generally powered by electricity, this study is focused on the analysis of the energy requirement in the irrigation sector and its application in developing strategies for groundwater over-pumping control at the county scale. 1) Field measurements from pumping tests are used to adjust the pumps' theoretical characteristics. A simple empirical equation is derived to estimate the energy use rate for irrigation given the depth of the groundwater table. Field measurements show that pump efficiency is around 30% in the tested region. 2) We hypothesize that the inter-annual variability of rural energy consumption is caused by the randomness in annual precipitation. This assumption is examined and then applied to separate the energy consumption for irrigation from the total rural energy consumption. 3) Based on the groundwater pumping rate

  5. Irrigation and Autocracy

    DEFF Research Database (Denmark)

    Bentzen, Jeanet Sinding; Kaarsen, Nicolai; Wingender, Asger Moll

    2017-01-01

    . We argue that the effect has historical origins: irrigation allowed landed elites in arid areas to monopolize water and arable land. This made elites more powerful and better able to oppose democratization. Consistent with this conjecture, we show that irrigation dependence predicts land inequality...

  6. Effective colostomy irrigation.

    Science.gov (United States)

    Mazier, W P; Dignan, R D; Capehart, R J; Smith, B G

    1976-06-01

    The ultimate goal of the cone method of colostomy irrigation is to return patients with colostomies to their former role in society with confidence in themselves to the extent that having a colostomy is not considered a handicap. The results have generally been excellent. We believe all patients with stomas should be afforded the opportunity to attempt colostomy irrigation.

  7. Plasma cleaning techniques and future applications in environmentally conscious manufacturing

    Energy Technology Data Exchange (ETDEWEB)

    Ward, P.P.

    1995-07-01

    Plasmas have frequently been used in industry as a last step surface preparation technique in an otherwise predominantly wet-etch process. The limiting factor in the usefulness of plasma cleaning techniques has been the rate at which organic materials are removed. Recent research in the field of plasma chemistry has provided some understanding of plasma processes. By controlling plasma conditions and gas mixtures, ultra-fast plasma cleaning and etching is possible. With enhanced organic removal rates, plasma processes become more desirable as an environmentally sound alternative to traditional solvent or acid dominated process, not only as a cleaning tool, but also as a patterning and machining tool. In this paper, innovations in plasma processes are discussed including enhanced plasma etch rates via plasma environment control and aggressive gas mixtures. Applications that have not been possible with the limited usefulness of past plasma processes are now approaching the realm of possibility. Some of these possible applications will be discussed along with their impact to environmentally conscious manufacturing.

  8. Artificial intelligence techniques for photovoltaic applications: A review

    Energy Technology Data Exchange (ETDEWEB)

    Mellit, Adel [Department of Electronics, Faculty of Sciences Engineering, LAMEL Laboratory, Jijel University, Oulad-aissa, P.O. Box 98, Jijel 18000 (Algeria); Kalogirou, Soteris A. [Department of Mechanical Engineering and Materials Science and Engineering, Cyprus University of Technology, P.O. Box 50329, Limassol 3603 (Cyprus)

    2008-10-15

    Artificial intelligence (AI) techniques are becoming useful as alternate approaches to conventional techniques or as components of integrated systems. They have been used to solve complicated practical problems in various areas and are becoming more popular nowadays. They can learn from examples, are fault tolerant in the sense that they are able to handle noisy and incomplete data, are able to deal with nonlinear problems and once trained can perform prediction and generalization at high speed. AI-based systems are being developed and deployed worldwide in a wide variety of applications, mainly because of their symbolic reasoning, flexibility and explanation capabilities. AI has been used in different sectors, such as engineering, economics, medicine, military, marine, etc. They have also been applied for modeling, identification, optimization, prediction, forecasting and control of complex systems. The paper outlines an understanding of how AI systems operate by way of presenting a number of problems in photovoltaic systems application. Problems presented include three areas: forecasting and modeling of meteorological data, sizing of photovoltaic systems and modeling, simulation and control of photovoltaic systems. Published literature presented in this paper show the potential of AI as design tool in photovoltaic systems. (author)

  9. Application of isotope techniques to investigate groundwater pollution

    International Nuclear Information System (INIS)

    1998-10-01

    This publication is a compilation of scientific results from the Co-ordinated Research Project (CRP) on the Application of Isotope Techniques to Investigate Groundwater Pollution which was implemented from 1995 to 1997. The conclusions of the CRP were presented by scientists from the following participating Member States: Austria, Brazil, China, Czech Republic, France, Hungary, India, Israel, Italy, New Zealand, Pakistan, Poland, Senegal and the United Kingdom. The CRP was implemented in recognition of the importance of protecting groundwater resources, and promoting the role of isotope techniques when integrated to classical hydrological methods to identify the sources and mechanisms of by which pollution takes place. The results of the CRP are expected to find practical applications in tackling hydrological problems encountered in technical co-operation projects of the IAEA. This publication could also provide a contribution toward the continuing efforts of various sectors to investigate, mitigate and control the threat of groundwater pollution. This publication includes the results of 16 investigations dealing with isotopes of hydrogen, carbon, nitrogen, oxygen and sulfur integrated to some extent with the classical hydrological tools of investigation. Each document in this compilation is provided with abstract and index

  10. Applicability of Operational Research Techniques in CANDU Nuclear Plant Maintenance

    International Nuclear Information System (INIS)

    Doyle, E. Kevin

    2002-01-01

    As previously reported at ICONE 6 in New Orleans, 1996, and ICONE 9 in Niece, 2001, the use of various maintenance optimization techniques at Bruce has lead to cost effective preventive maintenance applications for complex systems. Innovative practices included greatly reducing Reliability Centered Maintenance (RCM) costs while maintaining the accuracy of the analysis. The optimization strategy has undergone further evolution and at the present an Integrated Maintenance Program (IMP) is being put in place. Further cost refinement of the station preventive maintenance strategy whereby decisions are based on statistical analysis of historical failure data is being evaluated. A wide range of Operational Research (OR) literature was reviewed for implementation issues and several encouraging areas were found that will assist in the current effort of evaluating maintenance optimization techniques for nuclear power production. The road ahead is expected to consist first of resolving 25 years of data issues and preserving the data via appropriate knowledge system techniques while post war demographics permit experts to input into the system. Subsequent analytical techniques will emphasize total simplicity to obtain the requisite buy in from Corporate Executives who possibly are not trained in Operational Research. Case studies of containment airlock seal failures are used to illustrate the direct applicability of stochastic processes. Airlocks and transfer chambers were chosen as they have long been known as high maintenance items. Also, the very significant financial consequences of this type of failure will help to focus the attention of Senior Management on the effort. Despite substantial investment in research, improvement in the design of the seal material or configuration has not been achieved beyond the designs completed in the 1980's. Overall, the study showed excellent agreement of the relatively quick stochastic methods with the maintenance programs produced at

  11. Development of optical techniques for chemical engineering applications

    Energy Technology Data Exchange (ETDEWEB)

    Lamadie, F.; Charton, S.; Langlard, M. de; Ouattara, M.; Sentis, M. [CEA, Centre de Marcoule, DEN,DTEC,SGCS, F-30207 Marcoule (France)

    2016-07-01

    The design of separation processes for nuclear spend fuel treatment, dedicated to either research studies or industrial applications, is currently based on a phenomenological approach, relying on Computational Fluid Dynamics, and complemented by validation tests performed at small-scale. Indeed, most of the steps of the Purex process involve multiphasic flows (dissolution, leaching, liquid-liquid extraction, precipitation, filtration, etc.). Therefore an accurate knowledge of the dispersed phase properties is required in order to assess their coupling with the flow features, to predict the process performance and efficiency and to achieve size reduction or extrapolation. Hence, the measurements of particulate flows properties, and especially the particles (or drops or bubbles) size distribution, concentration (i.e. hold-up) and velocity has become a growing issue. Relevant techniques for measuring these flow properties are multiple, from the high-speed video acquisition coupled to image processing to the laser-induced fluorescence, including the particle imaging velocimetry or interferometric techniques (digital in-line holography, rainbow refractometry, etc.). In this communication, different techniques developed at CEA Marcoule for the characterization of multiphase flows, will be introduced. The strong interaction with computational fluid dynamics, in the scope of a multi-scale approach, will be discussed through typical results of gas-liquid, liquid-liquid and solid-liquid flows possibly encountered in nuclear fuel reprocessing process. (authors)

  12. Theory and applications of the dual energy technique

    International Nuclear Information System (INIS)

    Chuang, K.S.K.

    1986-01-01

    Three important principles in the dual energy technique applied to radiography are studied in this dissertation: the decomposition method, x-ray scatter consideration, and the selection of an optimal energy pair. First, two new methods namely, iso-transmission lines and sub-region direct approximation methods, are proposed for dual energy decomposition calculation. These two methods are compared with two other conventional techniques, i.e. nonlinear equations and direct approximation. The accuracy, efficiency, and smoothness are used as indices for comparison. The authors conclude that the two new proposed methods, iso-transmission lines and sub-region, are superior than the nonlinear equations and direct approximation methods. In this dissertation, a method to perform scatter correction based on the knowledge of scatter primary ratio is presented. First, the relation between scatter primary ratio and attenuation coefficient is determined by a Monte Carlo simulation. The selection of an optimal energy pair for a dual energy system is described in this dissertation. The selection is based on the calculation of an optimum factor which takes into consideration of the noise in the high and low energy images, the radiation dose to the patient, as well as the error produced during the dual energy decomposition process. The calculation of this optimum factor is obtained using monoenergetic radiation sources on various sizes of water phantom. In addition to these three aspects, this dissertation also addresses some clinical applications of the dual energy techniques and shows some of the results

  13. Surface dating of bricks, an application of luminescence techniques

    Science.gov (United States)

    Galli, Anna; Martini, Marco; Maspero, Francesco; Panzeri, Laura; Sibilia, Emanuela

    2014-05-01

    Luminescence techniques are a powerful tool to date archaeological ceramic materials and geological sediments. Thermoluminescence (TL) is widely used for bricks dating to reconstruct the chronology of urban complexes and the development of human cultures. However, it can sometimes be inconclusive, since TL assesses the firing period of bricks, which can be reused, even several centuries later. This problem can be circumvented using a dating technique based on a resetting event different from the last heating. OSL (Optically Stimulated Luminescence) exploits the last light exposition of the brick surface, which resets the light-sensitive electron traps until the surface is definitely shielded by mortar and superimposed bricks. This advanced application (surface dating) has been successfully attempted on rocks, marble and stone artifacts, but not yet on bricks. A recent conservation campaign at the Certosa di Pavia gave the opportunity to sample some bricks belonging to a XVII century collapsed wall, still tied to their mortars. This was an advantageous condition to test this technique, comparing the dating results with precise historical data. This attempt gave satisfactory results, allowing to identify bricks surely reused and to fully confirm that the edification of the perimetral wall occurred at the end of XVII century.

  14. Fetal magnetic resonance: technique applications and normal fetal anatomy

    International Nuclear Information System (INIS)

    Martin, C.; Darnell, A.; Duran, C.; Mellado, F.; Corona, M

    2003-01-01

    Ultrasonography is the preferred diagnostic imaging technique for intrauterine fetal examination. Nevertheless, circumstances sometimes dictate the use of other techniques in order to analyze fetal structures. The advent of ultra rapid magnetic resonance (MR) sequencing has led to the possibility of doing MR fetal studies, since images are obtained in an extradordiarily short time and are not affected by either maternal or fetal movements. It does not employ ionizing radiations, it provides high-contrast images and it can obtain such images in any plane of space without being influenced by either the child bearer's physical characteristics of fetal position. MR provides good quality images of most fetal organs. It is extremely useful in analysing distinct structures, as well as permitting an evaluation of cervical structures, lungs, diaphragms, intra-abdominal and retroperitoneal structures, and fetal extremities. It can also provide useful information regarding the placenta,umbilical cord, amniotic fluid and uterus. The objective of this work is to describe MR technique as applied to intrauterine fetal examination, and to illustrate normal fetal anatomy as manifested by MR and its applications. (Author) 42 refs

  15. Surface registration technique for close-range mapping applications

    Science.gov (United States)

    Habib, Ayman F.; Cheng, Rita W. T.

    2006-08-01

    Close-range mapping applications such as cultural heritage restoration, virtual reality modeling for the entertainment industry, and anatomical feature recognition for medical activities require 3D data that is usually acquired by high resolution close-range laser scanners. Since these datasets are typically captured from different viewpoints and/or at different times, accurate registration is a crucial procedure for 3D modeling of mapped objects. Several registration techniques are available that work directly with the raw laser points or with extracted features from the point cloud. Some examples include the commonly known Iterative Closest Point (ICP) algorithm and a recently proposed technique based on matching spin-images. This research focuses on developing a surface matching algorithm that is based on the Modified Iterated Hough Transform (MIHT) and ICP to register 3D data. The proposed algorithm works directly with the raw 3D laser points and does not assume point-to-point correspondence between two laser scans. The algorithm can simultaneously establish correspondence between two surfaces and estimates the transformation parameters relating them. Experiment with two partially overlapping laser scans of a small object is performed with the proposed algorithm and shows successful registration. A high quality of fit between the two scans is achieved and improvement is found when compared to the results obtained using the spin-image technique. The results demonstrate the feasibility of the proposed algorithm for registering 3D laser scanning data in close-range mapping applications to help with the generation of complete 3D models.

  16. Application of data mining techniques for nuclear data and instrumentation

    International Nuclear Information System (INIS)

    Toshniwal, Durga

    2013-01-01

    Data mining is defined as the discovery of previously unknown, valid, novel, potentially useful, and understandable patterns in large databases. It encompasses many different techniques and algorithms which differ in the kinds of data that can be analyzed and the form of knowledge representation used to convey the discovered knowledge. Patterns in the data can be represented in many different forms, including classification rules, association rules, clusters, etc. Data mining thus deals with the discovery of hidden trends and patterns from large quantities of data. The field of data mining is emerging as a new, fundamental research area with important applications to science, engineering, medicine, business, and education. It is an interdisciplinary research area and draws upon several roots, including database systems, machine learning, information systems, statistics and expert systems. Data mining, when performed on time series data, is known as time series data mining (TSDM). A time series is a sequence of real numbers, each number representing a value at a point of time. During the past few years, there has been an explosion of research in the area of time series data mining. This includes attempts to model time series data, to design languages to query such data, and to develop access structures to efficiently process queries on such data. Time series data arises naturally in many real-world applications. Efficient discovery of knowledge through time series data mining can be helpful in several domains such as: Stock market analysis, Weather forecasting etc. An important application area of data mining techniques is in nuclear power plant and related data. Nuclear power plant data can be represented in form of time sequences. Often it may be of prime importance to analyze such data to find trends and anomalies. The general goals of data mining include feature extraction, similarity search, clustering and classification, association rule mining and anomaly

  17. Potential applications of plasma science techniques for water treatment systems

    International Nuclear Information System (INIS)

    Pavlik, D.

    1994-01-01

    The historical evolution of water treatment techniques and their impact on man and his environment are presented. Ancient man recognized the relationship between good water and good health. However, it was not until the late 1800's that man's own contribution to the pollution of water via biological and chemical contamination of the water stream was recognized as having adverse affects on water quality. Since that time virtually every nation has adopted laws and regulations to ensure that safe sources of unpolluted water are available to its citizens. In the United States, water quality is governed by the Clean Water Act of 1972 administered at the federal level by the Environmental Protection Agency (EPA). Further, each state has established its equivalent agency which administers its own laws and regulations. Different biological and chemical biohazards present in the water system are discussed. Biological contaminants include various types of viruses, bacteria, fungii, molds, yeasts, algae, amoebas, and parasites. Chemical contaminates include elemental heavy metals and other organic and inorganic compounds which interfere with normal biological functions. Conventional water treatments for both consumption and sewage effluent commonly employ four different principals: mechanical filtration, quiescent gravity settling, biological oxidation, and chemical treatment. Although these techniques have greatly reduced the incidence of water-borne disease recent studies suggest that more effective means of eliminating biohazards are needed. Regulatory requirements for more aggressive treatment and elimination of residual contaminants present a significant opportunity for the application of various forms of electromagnetic radiation techniques. A comparison between conventional techniques and more advanced methods using various forms of electromagnetic radiation is discussed

  18. Income and irrigation water use efficiency under climate change: An application of spatial stochastic crop and water allocation model to Western Uzbekistan

    Directory of Open Access Journals (Sweden)

    Ihtiyor Bobojonov

    2016-01-01

    Results show farmers’ income could fall by as much as 25% with a 3.2 °C temperature increase and a 15% decline in irrigation. Farmers located in the tail end of the irrigation system could lose an even greater share of their revenues. A more conservative increase in temperature could increase farmer income by as much as 46% with a 2.2° temperature increase and only 8% decline in irrigation water since some crops benefit from extended vegetation periods. Under both pessimistic and optimistic scenarios, environmental challenges due to shallow groundwater tables may improve associated with enhanced water use efficiency.

  19. Application of drip irrigation technology for producing fruit of Salak ‘Gula Pasir’ (Salacca zalacca var. Gula Pasir off season on dry land

    Directory of Open Access Journals (Sweden)

    I N Rai

    2014-10-01

    Full Text Available Naturally, Salak Gula Pasir (Salacca zalacca var. Gula Pasir is flowering every three months or four times a year, but only one or two flowering seasons that the flowers can develop into fruit. The condition causes Salak Gula Pasir is available in the market in a short period (only 2-3 months i.e. at the time of harvest (on-season from December to February. This seasonal nature of Salak Gula Pasir occurs because Salak Gula Pasir is planted on dry land where irrigation depends only on rainfall, and drought occurs when water is shortage so that the plant internal water content is low that causes a high failure development rate of flower to become fruit (fruit-set failure. This study was aimed to overcome the fruit-set failure by providing drip irrigation. Two treatments (with drip irrigation and without drip irrigation/control with sixteen replicates were tested at Salak Gula Pasir production centre (at Sibetan village, Bebandem District, of Karangasem Regency, Bali at two harvest seasons, i.e. Gadu (July and Sela II (October. The results showed that the plant provided with drip irrigation significantly yielded fruit-set percentage higher that that without drip irrigation, both in Gadu and Sela II seasons. The percentages of fruit-set in Gadu and Sela II seasons provided with drip irrigation were 75.30% and 93.13%, respectively, while those without drip irrigation were only 59.94% and 61.67%, respectively. The increase of fruit-set observed for drip irrigation treatment associated with the increase of leaf chlorophyll content, relative water content (RWC of leaves, and leaf N, P, and K contents. The increase of fruit-set led to higher number of fruits and fruit weight per plant under drip irrigation than that without drip irrigation. Based on the results of this study, drip irrigation can be applied to produce Salak Gula Pasir planted out of season on dry land.

  20. The multi-sphere technique. 1 - general characteristics and applications; La technique multisphere. 1 - caracteristiques generales et applications

    Energy Technology Data Exchange (ETDEWEB)

    Zaborcwski, H [Commissariat a l' Energie Atomique, Cadarache (France). Centre d' Etudes Nucleaires

    1965-07-01

    A study is made of the general characteristics and the applications of the multisphere technique for flux measurements, dosimetry and the spectrometry of neutron sources ranging from thermal, up to 7 MeV neutrons. We give the equations relating to three fluxmeters (proportional long counters) for the measurements of the flux. Other equations have been derived : 1 - for multi-collision rad and rem dosimetry and first collision rad dosimetry; 2 - for the spectrometry and dosimetry of neutrons in five energy bands using a method similar to that used by threshold detectors. (author) [French] Nous etudions les caracteristiques generales et les applications de la technique multisphere pour les mesures de flux, la dosimetrie et la spectrometrie des sources de neutrons depuis les thermiques jusqu'a 7 MeV. Nous donnons les equations relatives a trois fluxmetres (longs compteurs equivalents) pour les mesures en flux. D'autres equations ont ete derivees: 1 - pour la dosimetrie en rad et en rem de multicollision et en rad de premiere collision; 2 - pour la spectrometrie et la dosimetrie des neutrons en cinq bandes energetiques suivant une methode voisine de celle utilisee par detecteurs a seuil. (auteur)

  1. LOW COST SMART SOLAR POWERED AUTOMATIC IRRIGATION SYSTEM

    OpenAIRE

    Hinsermu Alemayehu*, Kena Likassa

    2016-01-01

    In developing countries Photovoltaic energy can find many applications in agriculture, providing electrical energy in various cases, particularly OFF grid and desert area. Today Modern irrigation methods in developing country are needed to fulfill the food demands. Although in these countries Ethiopia, there are many diesel engine operated and rare solar operated water pumps for irrigation; but due to the running cost of diesel and capital cost of photovoltaic irrigation system. So Photovolta...

  2. Procedure for rapid determination of δ15N and δ18O values of nitrate: development and application to an irrigated rice paddy watershed.

    Science.gov (United States)

    Yada, Saeko; Nakajima, Yasuhiro; Itahashi, Sunao; Asada, Kei; Yoshikawa, Seiko; Eguchi, Sadao

    2016-01-01

    The dual isotope approach using the stable isotope ratios of nitrate nitrogen (δ(15)N(NO3)) and oxygen (δ(18)O(NO3)) is a strong tool for identifying the history of nitrate in various environments. Basically, a rapid procedure for determining δ(15)N(NO3) and δ(18)O(NO3) values is required to analyze many more samples quickly and thus save on the operational costs of isotope-ratio mass spectrometry (IRMS). We developed a new rapid procedure to save time by pre-treating consecutive samples of nitrous oxide microbially converted from nitrate before IRMS determination. By controlling two six-port valves of the pre-treatment system separately, IRMS determination of the current sample and backflush during the next sample pre-treatment period could be conducted simultaneously. A set of 89 samples was analyzed precisely during a 25-h continuous run (17 min per sample), giving the fastest reported processing time, and simultaneously reducing liquid nitrogen and carrier helium gas consumption by 35%. Application of the procedure to an irrigated rice paddy watershed suggested that nitrate concentrations in river waters decreased in a downstream direction, mainly because of the mixing of nitrate from different sources, without distinct evidence of denitrification. Our procedure should help with more detailed studies of nitrate formation processes in watersheds.

  3. Marketable yield of onion under different irrigation depths, with and without mulch

    Directory of Open Access Journals (Sweden)

    Daniel F. de Carvalho

    Full Text Available ABSTRACT The objectives of this study were to obtain the onion crop coefficients and evaluate the influence of different irrigation depths (0, 22, 45, 75 and 100% of crop evapotranspiration on marketable yield and quality of onion bulbs cultivated with and without mulch of elephant grass. The experiment was carried out in Seropédica, RJ, Brazil, from May to September 2012, in a Red Yellow Argisol. The experimental design was in randomized blocks in split plots, with 10 treatments and seven replicates. Irrigation management was performed through soil water balance using the Time Domain Reflectometry technique, with probes installed horizontally at 7.5 and 22.5 cm depths. The use of mulch allowed the application of smaller irrigation depths, leading to lower crop coefficient (18% in stage II and 3% in stage III in comparison to the crop without mulch. Irrigation depths associated with the use of mulch influenced the evaluated production variables, proving to be an alternative to increase marketable yield and quality of onion bulbs, with lower irrigation depth.

  4. Application of neutron backscatter techniques to level measurement problems

    International Nuclear Information System (INIS)

    Leonardi-Cattolica, A.M.; McMillan, D.H.; Telfer, A.; Griffin, L.H.; Hunt, R.H.

    1982-01-01

    We have designed and built portable level detectors and fixed level monitors based on neutron scattering and detection principles. The main components of these devices, which we call neutron backscatter gauges, are a neutron emitting radioisotope, a neutron detector, and a ratemeter. The gauge is a good detector for hydrogen but is much less sensitive to most other materials. This allows level measurements of hydrogen bearing materials, such as hydrocarbons, to be made through the walls of metal vessels. Measurements can be made conveniently through steel walls which are a few inches thick. We have used neutron backscatter gauges in a wide variety of level measurement applications encountered in the petrochemical industry. In a number of cases, the neutron techniques have proven to be superior to conventional level measurement methods, including gamma ray methods

  5. Application of multivariate techniques to analytical data on Aegean ceramics

    International Nuclear Information System (INIS)

    Bieber, A.M.; Brooks, D.W.; Harbottle, G.; Sayre, E.V.

    1976-01-01

    The general problems of data collection and handling for multivariate elemental analyses of ancient pottery are considered including such specific questions as the level of analytical precision required, the number and type of elements to be determined and the need for comprehensive multivariate statistical analysis of the collected data in contrast to element by element statistical analysis. The multivariate statistical procedures of clustering in a multidimensional space and determination of the numerical probabilities of specimens belonging to a group through calculation of the Mahalanobis distances for these specimens in multicomponent space are described together with supporting univariate statistical procedures used at Brookhaven. The application of these techniques to the data on Late Bronze Age Aegean pottery (largely previously analysed at Oxford and Brookhaven with some new specimens considered) have resulted in meaningful subdivisions of previously established groups. (author)

  6. Physics of nuclear radiations concepts, techniques and applications

    CERN Document Server

    Rangacharyulu, Chary

    2013-01-01

    Physics of Nuclear Radiations: Concepts, Techniques and Applications makes the physics of nuclear radiations accessible to students with a basic background in physics and mathematics. Rather than convince students one way or the other about the hazards of nuclear radiations, the text empowers them with tools to calculate and assess nuclear radiations and their impact. It discusses the meaning behind mathematical formulae as well as the areas in which the equations can be applied. After reviewing the physics preliminaries, the author addresses the growth and decay of nuclear radiations, the stability of nuclei or particles against radioactive transformations, and the behavior of heavy charged particles, electrons, photons, and neutrons. He then presents the nomenclature and physics reasoning of dosimetry, covers typical nuclear facilities (such as medical x-ray machines and particle accelerators), and describes the physics principles of diverse detectors. The book also discusses methods for measuring energy a...

  7. Digital fluoroscopy: Technique and applications for evaluating left ventricular function

    International Nuclear Information System (INIS)

    Higgins, C.B.; Norris, S.L.; Gerber, K.H.; Ashburn, W.L.; Slutsky, R.A.

    1985-01-01

    Central cardiovascular dynamics can be studied without cardiac catheterization by digital processing of fluoroscopic images of the heart obtained after central intravenous injection of contrast media. While digital subtraction angiography has been used for studying peripheral vasculature for several years, it is only recently that this technique has been applied for assessing cardiac morphology and physiology. The conversion of fluoroscopic x-ray data into a digital form has an added advantage for the study of the central cardiovascular system since it not only permits contrast enhancement of the images but also facilitates quantitative and functional analysis of the x-ray data. The several applications described in this chapter suggest that digital subtraction cardiovascular angiography will prove to be a powerful tool for studying cardiovascular physiology in animals and for evaluating heart disease in patients

  8. Application of modern reliability database techniques to military system data

    International Nuclear Information System (INIS)

    Bunea, Cornel; Mazzuchi, Thomas A.; Sarkani, Shahram; Chang, H.-C.

    2008-01-01

    This paper focuses on analysis techniques of modern reliability databases, with an application to military system data. The analysis of military system data base consists of the following steps: clean the data and perform operation on it in order to obtain good estimators; present simple plots of data; analyze the data with statistical and probabilistic methods. Each step is dealt with separately and the main results are presented. Competing risks theory is advocated as the mathematical support for the analysis. The general framework of competing risks theory is presented together with simple independent and dependent competing risks models available in literature. These models are used to identify the reliability and maintenance indicators required by the operating personnel. Model selection is based on graphical interpretation of plotted data

  9. The application of irradiation techniques to food and foodstuffs

    International Nuclear Information System (INIS)

    Kwon, Joong Ho; Cho, Han Ok; Byun, Myung Woo; Kim, Suck Won; Yang, Jae Seung

    1993-01-01

    With a view to establishing concrete infrastructures for the enlarged utilization of irradiation techniques in the food industries, the efficacy of gamma irradiation was investigated for both soybeans having problems in water-soaking process before mass-processing and dried-red pepper requiring long-term storage. Irradiation of 5 kGy was found effective for the reduction of soaking and cooking time of soybeans, but negligible changes were induced by irradiation in their nutritional components and processing properties (Tofu,soymilk). Air-tight packaging was suitable for the keeping quality of dried red pepper and irradiation applications were more effective in powdered samples than in whole pepper for preserving and improving their quality. (Author)

  10. Remotely-Sensed Mapping of Irrigation Area in the Chu-Talas River Basin in Central Asia and Application to Compliance Monitoring of Transboundary Water Sharing

    Science.gov (United States)

    Ragettli, S.; Siegfried, T.; Herberz, T.

    2017-12-01

    In the Central Asian Chu-Talas River Basin, farmers depend on freshwater from international rivers to irrigate their fields during the summer growing season. While the allocation percentages of water sharing between up- and downstream are defined for both rivers, marked interannual supply variability plus inadequate monitoring renders the compliance with these quotas difficult. In such circumstances, data on irrigated area obtained by remote sensing can be used to map the extent of irrigation in terms of its area on at national and subnational scales. Due to its transparency on how the data was obtained (freely available satellite data) and processed, this objective measure could potentially be used as a data product for confidence building and for compliance monitoring. This study assesses the extent and location of irrigated areas over the period 2000 - 2016 in the basins by using state-of-the-art remote sensing technology. Using a random forest classifier, an automated irrigated cropland mapping algorithm was implemented in Google Earth Engine using Landsat 7 data. First, a training set was established through visual interpretation (irrigated and non-irrigated classes for the year 2015) and the classifier then trained. The classier was then applied on a series of seasonal greenest pixels image mosaics from 2000 to 2016. A four-stepped accuracy assessment confirmed that the classifier yielded robust, reliable and reproducible results. Outcomes indicate that irrigated areas in the Kyrgyz side of the Talas Basin approximately doubled by 2016 since 2000 while the irrigated area in the Kazakh part of the basin did not significantly change over the 17 year time period. In the Chu River Basin, total irrigated area tripled since 2000. Comparison with officially reported statistics shows differences and points to reporting issues in both countries. We conclude that remote sensing of irrigated areas in arid and semi-arid regions in combination with cloud computing offers

  11. Carbon and water footprints of irrigated corn and non-irrigated wheat in Northeast Spain.

    Science.gov (United States)

    Abrahão, Raphael; Carvalho, Monica; Causapé, Jesús

    2017-02-01

    Irrigation increases yields and allows several crops to be produced in regions where it would be naturally impossible due to limited rainfall. However, irrigation can cause several negative environmental impacts, and it is important to understand these in depth for the correct application of mitigation measures. The life cycle assessment methodology was applied herein to compare the main irrigated and non-irrigated crops in Northeast Spain (corn and wheat, respectively), identifying those processes with greater contribution to environmental impacts (carbon and water footprint categories) and providing scientifically-sound information to facilitate government decisions. Due to concerns about climate change and water availability, the methods selected for evaluation of environmental impacts were IPCC 2013 GWP (carbon footprint) and water scarcity indicator (water footprint). The area studied, a 7.38-km 2 basin, was monitored for 12 years, including the period before, during, and after the implementation of irrigation. The functional unit, to which all material and energy flows were associated with, was the cultivation of 1 ha, throughout 1 year. The overall carbon footprint for irrigated corn was higher, but when considering the higher productivity achieved with irrigation, the emissions per kilogram of corn decrease and finally favor this irrigated crop. When considering the water footprint, the volumes of irrigation water applied were so high that productivity could not compensate for the negative impacts associated with water use in the case of corn. Nevertheless, consideration of productivities and gross incomes brings the results closer. Fertilizer use (carbon footprint) and irrigation water (water footprint) were the main contributors to the negative impacts detected.

  12. The application of microwave techniques to temperature measurement in biotelemetry

    International Nuclear Information System (INIS)

    Glajchen, M.

    1984-01-01

    The use of a microwave dielectric resonator for temperature measurement in Biotelemetry offers the advantage that a passive temperature telemeter can be used. The telemeter is powered by a source remote from the host creature, thus permitting greater miniaturisation of the implant than is possible with conventional techniques. This is essential, especially for application to small animals where the telemeter size and weight become critical. The design of the telemeter which is based upon a novel microwave technique, and the associated practical considerations are discussed. Included in this work is a criticism of initially promising ideas which after an in-depth investigation had to be disregarded. Although the transponder could not be built in its final form due to the unavailability of certain key materials, the transponder operation was tested and found to be successful. A specification of the transponder and transmitter requirements for a working system are included. A theoretical and experimental appraisal of dielectric resonators as miniature microwave filters, also forms a large part of this work. Dielectric resonators offer a significant volume reduction compared to air-filled metallic cavities, and simple coupling to microstrip combined with ease of tuning permits incorporation into Microwave Integrated Circuits. A computer program which can form the basis for a dielectric resonator filter design is provided, and some unusual results of tests on dielectric resonators are presented. It is believed that this will help to popularise and increase understanding of the dielectric resonator - which is an exciting, yet still emerging technology

  13. Surgical Tips in Frozen Abdomen Management: Application of Coliseum Technique.

    Science.gov (United States)

    Kyriazanos, Ioannis D; Manatakis, Dimitrios K; Stamos, Nikolaos; Stoidis, Christos

    2015-01-01

    Wound dehiscence is a serious postoperative complication, with an incidence of 0.5-3% after primary closure of a laparotomy incision, and represents an acute mechanical failure of wound healing. Relatively recently the concept of "intentional open abdomen" was described and both clinical entities share common pathophysiological and clinical pathways ("postoperative open abdominal wall"). Although early reconstruction is the target, a significant proportion of patients will develop adhesions between abdominal viscera and the anterolateral abdominal wall, a condition widely recognized as "frozen abdomen," where delayed wound closure appears as the only realistic alternative. We report our experience with a patient who presented with frozen abdomen after wound dehiscence due to surgical site infection and application of the "Coliseum technique" for its definitive surgical management. This novel technique represents an innovative alternative to abdominal exploration, for cases of "malignant" frozen abdomen due to peritoneal carcinomatosis. Lifting the edges of the surgical wound upwards and suspending them under traction by threads from a retractor positioned above the abdomen facilitates approach to the peritoneal cavity, optimizes exposure of intra-abdominal organs, and prevents operative injury to the innervation and blood supply of abdominal wall musculature, a crucial step for subsequent hernia repair.

  14. Applications of pattern recognition techniques to online fault detection

    International Nuclear Information System (INIS)

    Singer, R.M.; Gross, K.C.; King, R.W.

    1993-01-01

    A common problem to operators of complex industrial systems is the early detection of incipient degradation of sensors and components in order to avoid unplanned outages, to orderly plan for anticipated maintenance activities and to assure continued safe operation. In such systems, there usually are a large number of sensors (upwards of several thousand is not uncommon) serving many functions, ranging from input to control systems, monitoring of safety parameters and component performance limits, system environmental conditions, etc. Although sensors deemed to measure important process conditions are generally alarmed, the alarm set points usually are just high-low limits and the operator's response to such alarms is based on written procedures and his or her experience and training. In many systems this approach has been successful, but in situations where the cost of a forced outage is high an improved method is needed. In such cases it is desirable, if not necessary, to detect disturbances in either sensors or the process prior to any actual failure that could either shut down the process or challenge any safety system that is present. Recent advances in various artificial intelligence techniques have provided the opportunity to perform such functions of early detection and diagnosis. In this paper, the experience gained through the application of several pattern-recognition techniques to the on-line monitoring and incipient disturbance detection of several coolant pumps and numerous sensors at the Experimental Breeder Reactor-II (EBR-II) which is located at the Idaho National Engineering Laboratory is presented

  15. Quantum theory of many-body systems techniques and applications

    CERN Document Server

    Zagoskin, Alexandre

    2014-01-01

    This text presents a self-contained treatment of the physics of many-body systems from the point of view of condensed matter. The approach, quite traditionally, uses the mathematical formalism of quasiparticles and Green’s functions. In particular, it covers all the important diagram techniques for normal and superconducting systems, including the zero-temperature perturbation theory and the Matsubara, Keldysh and Nambu-Gor'kov formalism, as well as an introduction to Feynman path integrals. This new edition contains an introduction to the methods of theory of one-dimensional systems (bosonization and conformal field theory) and their applications to many-body problems.   Intended for graduate students in physics and related fields, the aim is not to be exhaustive, but to present enough detail to enable the student to follow the current research literature, or to apply the techniques to new problems. Many of the examples are drawn from mesoscopic physics, which deals with systems small enough that quantum...

  16. Modern trends: analytical chemistry - techniques and application to biodetection

    International Nuclear Information System (INIS)

    Khurshid, S.J.

    1993-01-01

    Microorganism isolated from specimens are usually identified by conventional bacterial identification procedures of morphological evaluation and cultural techniques. These complex methods of studying organisms are extremely tedious and time consuming. This causes serious problems by delaying the decision concerning the presence of pathogens and therefore the adequate drug therapy. Frequently, the decision about the presence of pathogens has to be made prior to the results of microbiological tests. In order to overcome these conditions, workers explored new instrumental methods for characterization, rapid acquisition, high reproducibility, computer aided data recording and interpretation of microorganisms. This article brief reviews application of these modern instrumental approaches such as Infrared Spectroscopy (IR), Gas Chromatography (GC), Fluorescence Spectroscopy, Bioluminescence, Chemiluminescence, FLow Cytometry, Micro calorimetry, GC-MASS Spectrometry, Electrical Impedance, Bio sensors and Radiometry. These techniques have increased the capacity of doing basic research with a major impact on both the clinical laboratories and industry. The radiometric procedure is being used for research and biological quality control of radiopharmaceuticals in our laboratory at PINSTECH. (author)

  17. Prewarping techniques in imaging: applications in nanotechnology and biotechnology

    Science.gov (United States)

    Poonawala, Amyn; Milanfar, Peyman

    2005-03-01

    In all imaging systems, the underlying process introduces undesirable distortions that cause the output signal to be a warped version of the input. When the input to such systems can be controlled, pre-warping techniques can be employed which consist of systematically modifying the input such that it cancels out (or compensates for) the process losses. In this paper, we focus on the mask (reticle) design problem for 'optical micro-lithography', a process similar to photographic printing used for transferring binary circuit patterns onto silicon wafers. We use a pixel-based mask representation and model the above process as a cascade of convolution (aerial image formation) and thresholding (high-contrast recording) operations. The pre-distorted mask is obtained by minimizing the norm of the difference between the 'desired' output image and the 'reproduced' output image. We employ the regularization framework to ensure that the resulting masks are close-to-binary as well as simple and easy to fabricate. Finally, we provide insight into two additional applications of pre-warping techniques. First is 'e-beam lithography', used for fabricating nano-scale structures, and second is 'electronic visual prosthesis' which aims at providing limited vision to the blind by using a prosthetic retinally implanted chip capable of electrically stimulating the retinal neuron cells.

  18. Application Of Nuclear Techniques In Environmental Studies And Pollution Control

    Energy Technology Data Exchange (ETDEWEB)

    EI-Motaium, R A [Plant Research Department, Nuclear Research Ceter, Atomic Energy Authority, Inshas P.O. Box 13759, Cairo (Egypt)

    2007-07-01

    Environmental pollution has become a world wide concern. One of the main sources of such pollution is sewage wastewater and sludge. Their utilization without proper treatment can pollute the ecosystem (plant, soil, surface and ground water). Sewage wastewater and sludge contains several pollutants such as: pathogens, toxic organic compounds, heavy metals, high level of BOD and COD, seed weed. The reuse of sewage water and sludge in agriculture can lead to the transfer of some of these pollutants into the food chain causing health hazard. In addition, most of these contaminants are not biodegradable, becoming dangerous to plant and human health. Nuclear techniques has recently been used to control environmental pollution. Ionizing radiation provide a fast and reliable means of sewage water and sludge treatment than the conventional methods. Gamma radiation ( {sup 60}Co) and electron beam (accelerator) has been successfully used for alleviation of environmental pollution. Such alleviation includes: disinfection of harmful pathogens, degradation of toxic organic pollutants, destruction of seed weed and reduction of soluble heavy metals, odor and BOD and COD. The use of radioactive and stable isotopes are a useful tools to investigate the contribution of sludge nutrients to plant nutrition. Nitrogen, using {sup 15}N-ammonium sulfate, uptake and translocation by plant from soil amended with sewage sludge was studied under field condition. The contribution of sludge to phosphorus nutrition of plants was quantified using {sup 32}p as tracer. In both cases the principal of isotopic dilution technique was applied. The information generated from these experiments could help preserve the environment. It could help optimize the application rate of sludge to meet plant requirements while avoiding the accumulation of N and P in the soil or leaching to the aquifer. Isotope exchange kinetic technique is used to evaluate nutrients availability from sludge. Neutron moisture meter is

  19. Application Of Nuclear Techniques In Environmental Studies And Pollution Control

    International Nuclear Information System (INIS)

    EI-Motaium, R.A.

    2007-01-01

    Environmental pollution has become a world wide concern. One of the main sources of such pollution is sewage wastewater and sludge. Their utilization without proper treatment can pollute the ecosystem (plant, soil, surface and ground water). Sewage wastewater and sludge contains several pollutants such as: pathogens, toxic organic compounds, heavy metals, high level of BOD and COD, seed weed. The reuse of sewage water and sludge in agriculture can lead to the transfer of some of these pollutants into the food chain causing health hazard. In addition, most of these contaminants are not biodegradable, becoming dangerous to plant and human health. Nuclear techniques has recently been used to control environmental pollution. Ionizing radiation provide a fast and reliable means of sewage water and sludge treatment than the conventional methods. Gamma radiation ( 60 Co) and electron beam (accelerator) has been successfully used for alleviation of environmental pollution. Such alleviation includes: disinfection of harmful pathogens, degradation of toxic organic pollutants, destruction of seed weed and reduction of soluble heavy metals, odor and BOD and COD. The use of radioactive and stable isotopes are a useful tools to investigate the contribution of sludge nutrients to plant nutrition. Nitrogen, using 15 N-ammonium sulfate, uptake and translocation by plant from soil amended with sewage sludge was studied under field condition. The contribution of sludge to phosphorus nutrition of plants was quantified using 32 p as tracer. In both cases the principal of isotopic dilution technique was applied. The information generated from these experiments could help preserve the environment. It could help optimize the application rate of sludge to meet plant requirements while avoiding the accumulation of N and P in the soil or leaching to the aquifer. Isotope exchange kinetic technique is used to evaluate nutrients availability from sludge. Neutron moisture meter is used to

  20. Applications of Graph Spectral Techniques to Water Distribution Network Management

    Directory of Open Access Journals (Sweden)

    Armando di Nardo

    2018-01-01

    Full Text Available Cities depend on multiple heterogeneous, interconnected infrastructures to provide safe water to consumers. Given this complexity, efficient numerical techniques are needed to support optimal control and management of a water distribution network (WDN. This paper introduces a holistic analysis framework to support water utilities on the decision making process for an efficient supply management. The proposal is based on graph spectral techniques that take advantage of eigenvalues and eigenvectors properties of matrices that are associated with graphs. Instances of these matrices are the adjacency matrix and the Laplacian, among others. The interest for this application is to work on a graph that specifically represents a WDN. This is a complex network that is made by nodes corresponding to water sources and consumption points and links corresponding to pipes and valves. The aim is to face new challenges on urban water supply, ranging from computing approximations for network performance assessment to setting device positioning for efficient and automatic WDN division into district metered areas. It is consequently created a novel tool-set of graph spectral techniques adapted to improve main water management tasks and to simplify the identification of water losses through the definition of an optimal network partitioning. Two WDNs are used to analyze the proposed methodology. Firstly, the well-known network of C-Town is investigated for benchmarking of the proposed graph spectral framework. This allows for comparing the obtained results with others coming from previously proposed approaches in literature. The second case-study corresponds to an operational network. It shows the usefulness and optimality of the proposal to effectively manage a WDN.

  1. Comparison of Manual and Automatic Irrigation of Pot Experiments

    DEFF Research Database (Denmark)

    Haahr, Vagner

    1975-01-01

    An air-lift principle for transport of water was adapted for automatic irrigation of experimental pots originally constructed for manual irrigation by the weighing method. The two irrigation techniques were compared in an experiment with increasing amounts of nitrogen fertilizer to spring barley....... Productions of grain and straw and chemical composition were almost the same after the two irrigation methods, and it was concluded that the laborious manual watering could be replaced by automatic irrigation. Comparison of the yield from individual plants in the pots showed a large difference between centre...... plants and border plants independent of irrigation principle. The increase in yield per pot with increasing N fertilization was at the highest N level caused only by an increase in yield of the border plants....

  2. New Complexity Scalable MPEG Encoding Techniques for Mobile Applications

    Directory of Open Access Journals (Sweden)

    Stephan Mietens

    2004-03-01

    Full Text Available Complexity scalability offers the advantage of one-time design of video applications for a large product family, including mobile devices, without the need of redesigning the applications on the algorithmic level to meet the requirements of the different products. In this paper, we present complexity scalable MPEG encoding having core modules with modifications for scalability. The interdependencies of the scalable modules and the system performance are evaluated. Experimental results show scalability giving a smooth change in complexity and corresponding video quality. Scalability is basically achieved by varying the number of computed DCT coefficients and the number of evaluated motion vectors but other modules are designed such they scale with the previous parameters. In the experiments using the “Stefan” sequence, the elapsed execution time of the scalable encoder, reflecting the computational complexity, can be gradually reduced to roughly 50% of its original execution time. The video quality scales between 20 dB and 48 dB PSNR with unity quantizer setting, and between 21.5 dB and 38.5 dB PSNR for different sequences targeting 1500 kbps. The implemented encoder and the scalability techniques can be successfully applied in mobile systems based on MPEG video compression.

  3. Nuclear Analytical Techniques for Commercial Applications in China

    International Nuclear Information System (INIS)

    Chai, Z.; Zhang, Z.; Feng, S.; Yang, J.; Ouyang, H.; Feng, X.; Mao, X.

    2013-01-01

    Since the establishment of the first Chinese nuclear reactor and accelerator in 1958, the nuclear analytical techniques (NATs) in China have dramatically developed in past half century. Nowadays 10 research nuclear reactors and over 100 small accelerators are available in China. Roughly, about 50 % of the machine time is applied for commercial purpose at the moment. The versatile nuclear analytical methods, mainly NAA, PIXE, XRF, etc., in China have been and are being applied widely and extensively in the following three fields: scientific, training, and commercial. This paper will briefly describe the past experience and present status about NATs for commercial applications. Some practical examples to demonstrate the role of NATs in this aspect will be given as well. Basically, the NATs used for the commercial applications in China can be divided into two types, i.e. off-line and on-line. The former mainly includes instrumental neutron activation analysis (INAA) for compositional determination, particle induced X-ray emission (PIXE) also for compositional analysis, accelerator-based mass-spectrometry (AMS) for analysis of C-14, Be-7, Cl-36 and other long-lived radioactive nuclides, solid state nuclear track detector

  4. Processing Techniques and Applications of Silk Hydrogels in Bioengineering

    Directory of Open Access Journals (Sweden)

    Michael Floren

    2016-09-01

    Full Text Available Hydrogels are an attractive class of tunable material platforms that, combined with their structural and functional likeness to biological environments, have a diversity of applications in bioengineering. Several polymers, natural and synthetic, can be used, the material selection being based on the required functional characteristics of the prepared hydrogels. Silk fibroin (SF is an attractive natural polymer for its excellent processability, biocompatibility, controlled degradation, mechanical properties and tunable formats and a good candidate for the fabrication of hydrogels. Tremendous effort has been made to control the structural and functional characteristic of silk hydrogels, integrating novel biological features with advanced processing techniques, to develop the next generation of functional SF hydrogels. Here, we review the several processing methods developed to prepare advanced SF hydrogel formats, emphasizing a bottom-up approach beginning with critical structural characteristics of silk proteins and their behavior under specific gelation environments. Additionally, the preparation of SF hydrogel blends and other advanced formats will also be discussed. We conclude with a brief description of the attractive utility of SF hydrogels in relevant bioengineering applications.

  5. Yield response and economics of shallow subsurface drip irrigation systems

    Science.gov (United States)

    Field tests were conducted using shallow subsurface drip irrigation (S3DI) on cotton (Gossypium hirsutum, L.), corn (Zea mays, L.), and peanut (Arachis hypogeae, L.) in rotation to investigate yield potential and economic sustainability of this irrigation system technique over a six year period. Dri...

  6. Grower demand for sensor-controlled irrigation

    Science.gov (United States)

    Lichtenberg, Erik; Majsztrik, John; Saavoss, Monica

    2015-01-01

    Water scarcity is likely to increase in the coming years, making improvements in irrigation efficiency increasingly important. An emerging technology that promises to increase irrigation efficiency substantially is a wireless irrigation sensor network that uploads sensor data into irrigation management software, creating an integrated system that allows real-time monitoring and control of moisture status that has been shown in experimental settings to reduce irrigation costs, lower plant loss rates, shorten production times, decrease pesticide application, and increase yield, quality, and profit. We use an original survey to investigate likely initial acceptance, ceiling adoption rates, and profitability of this new sensor network technology in the nursery and greenhouse industry. We find that adoption rates for a base system and demand for expansion components are decreasing in price, as expected. The price elasticity of the probability of adoption suggests that sensor networks are likely to diffuse at a rate somewhat greater than that of drip irrigation. Adoption rates for a base system and demand for expansion components are increasing in specialization in ornamental production: growers earning greater shares of revenue from greenhouse and nursery operations are willing to pay more for a base system and are willing to purchase larger numbers of expansion components at any given price. We estimate that growers who are willing to purchase a sensor network expect investment in this technology to generate significant profit, consistent with findings from experimental studies.

  7. Root Zone Sensors for Irrigation Management in Intensive Agriculture

    Directory of Open Access Journals (Sweden)

    Jochen Hemming

    2009-04-01

    Full Text Available Crop irrigation uses more than 70% of the world’s water, and thus, improving irrigation efficiency is decisive to sustain the food demand from a fast-growing world population. This objective may be accomplished by cultivating more water-efficient crop species and/or through the application of efficient irrigation systems, which includes the implementation of a suitable method for precise scheduling. At the farm level, irrigation is generally scheduled based on the grower’s experience or on the determination of soil water balance (weather-based method. An alternative approach entails the measurement of soil water status. Expensive and sophisticated root zone sensors (RZS, such as neutron probes, are available for the use of soil and plant scientists, while cheap and practical devices are needed for irrigation management in commercial crops. The paper illustrates the main features of RZS’ (for both soil moisture and salinity marketed for the irrigation industry and discusses how such sensors may be integrated in a wireless network for computer-controlled irrigation and used for innovative irrigation strategies, such as deficit or dual-water irrigation. The paper also consider the main results of recent or current research works conducted by the authors in Tuscany (Italy on the irrigation management of container-grown ornamental plants, which is an important agricultural sector in Italy.

  8. Investigation of the effects of slow-release fertilizer and struvite in biodegradation in filter drains and potential application of treated water in irrigation of road verges.

    Science.gov (United States)

    Theophilus, Stephen C; Mbanaso, Fredrick U; Nnadi, Ernest O; Onyedeke, Kingsley T

    2017-11-14

    Filter drains are usually laid along the margins of highways. Highway runoffs are polluted with hydrocarbons and high levels of total dissolved solids. Therefore, effective pollution removal mechanism is necessary in order to avoid contamination of surrounding soils and groundwater. Biodegradation is amongst pollution removal mechanisms in filter drains, but it is a relatively slow process which is dependent on wide range of factors including the type of pollutant and availability of nutrients. This paper reports on a study conducted to investigate the impact of slow-release fertilizer and struvite in enhancement of biodegradation of hydrocarbon in filter drains. Filter drain models incorporated with geotextile were challenged with cumulative oil loading of 178 mg/m 2 /week with a view to comparing the efficiency of these two nutrient sources under high oil pollution loading and realistic rainfall conditions of 13 mm/week. Nutrients and street dust were applied at one-off rate of 17 g/m 2 and 1.55 g/rig to provide nutrient enhancement and simulate field conditions respectively. The impact of the nutrients was studied by monitoring bacterial and fungal growth using nutrient agar, Rose Bengal Agar media and CO2 evolution. EC, pH, heavy metals, TPH, elemental analysis and SAR were used to investigate water quality of effluent of filter drains for potential application as irrigation fluid for trees and flowers planted on road verges. The results show that nutrient application encouraged microbial activities and enhanced biodegradation rates with differences in type of nutrient applied. Also, it was observed that incorporation of geotextiles in filter drains improved pollution retention efficiency and there is a potential opportunity for utilization of struvite in SuDS systems as sustainable nutrient source.

  9. Decision-making in irrigation networks: Selecting appropriate canal structures using multi-attribute decision analysis.

    Science.gov (United States)

    Hosseinzade, Zeinab; Pagsuyoin, Sheree A; Ponnambalam, Kumaraswamy; Monem, Mohammad J

    2017-12-01

    The stiff competition for water between agriculture and non-agricultural production sectors makes it necessary to have effective management of irrigation networks in farms. However, the process of selecting flow control structures in irrigation networks is highly complex and involves different levels of decision makers. In this paper, we apply multi-attribute decision making (MADM) methodology to develop a decision analysis (DA) framework for evaluating, ranking and selecting check and intake structures for irrigation canals. The DA framework consists of identifying relevant attributes for canal structures, developing a robust scoring system for alternatives, identifying a procedure for data quality control, and identifying a MADM model for the decision analysis. An application is illustrated through an analysis for automation purposes of the Qazvin irrigation network, one of the oldest and most complex irrigation networks in Iran. A survey questionnaire designed based on the decision framework was distributed to experts, managers, and operators of the Qazvin network and to experts from the Ministry of Power in Iran. Five check structures and four intake structures were evaluated. A decision matrix was generated from the average scores collected from the survey, and was subsequently solved using TOPSIS (Technique for Order of Preference by Similarity to Ideal Solution) method. To identify the most critical structure attributes for the selection process, optimal attribute weights were calculated using Entropy method. For check structures, results show that the duckbill weir is the preferred structure while the pivot weir is the least preferred. Use of the duckbill weir can potentially address the problem with existing Amil gates where manual intervention is required to regulate water levels during periods of flow extremes. For intake structures, the Neyrpic® gate and constant head orifice are the most and least preferred alternatives, respectively. Some advantages

  10. Geochemical Exploration Techniques Applicable in the Search for Copper Deposits

    Science.gov (United States)

    Chaffee, Maurice A.

    1975-01-01

    media. Samples of ice and snow have been used for limited geochemical surveys. Both geobotanical and biogeochemical surveys have been successful in locating copper deposits in many parts of the world. Micro-organisms, including bacteria and algae, are other unproved media that should be studied. Animals can be used in geochemical-prospecting programs. Dogs have been used quite successfully to sniff out hidden and exposed sulfide minerals. Tennite mounds are commonly composed of subsurface material, but have not as yet proved to be useful in locating buried mineral deposits. Animal tissue and waste products are essentially unproved but potentially valuable sampling media. Knowledge of the location of areas where trace-element-associated diseases in animals and man are endemic as well as a better understanding of these diseases, may aid in identifying regions that are enriched in or depleted of various elements, including copper. Results of analyses of gases in the atmosphere are proving valuable in mineral-exploration surveys. Studies involving metallic compounds exhaled by plants into the atmosphere, and of particulate matter suspended in the atmosphere are reviewed these methods may become important in the future. Remote-sensing techniques are useful for making indirect measurements of geochemical responses. Two techniques applicable to geochemical exploration are neutron-activation analysis and gamma-ray spectrometry. Aerial photography is especially useful in vegetation surveys. Radar imagery is an unproved but potentially valuable method for use in studies of vegetation in perpetually clouded regions. With the advent of modern computers, many new techniques, such as correlation analysis, regression analysis, discriminant analysis, factor analysis, cluster analysis, trend-surface analysis, and moving-average analysis can be applied to geochemical data sets. Selective use of these techniques can provide new insights into the interpretatio

  11. Where Does the Irrigation Water Go? An Estimate of the Contribution of Irrigation to Precipitation Using MERRA

    Science.gov (United States)

    Wei, Jiangfeng; Dirmeyer, Paul A.; Wisser, Dominik; Bosilovich, Michael G.; Mocko, David M.

    2013-01-01

    Irrigation is an important human activity that may impact local and regional climate, but current climate model simulations and data assimilation systems generally do not explicitly include it. The European Centre for Medium-Range Weather Forecasts (ECMWF) Interim Re-Analysis (ERA-Interim) shows more irrigation signal in surface evapotranspiration (ET) than the Modern-Era Retrospective Analysis for Research and Applications (MERRA) because ERA-Interim adjusts soil moisture according to the observed surface temperature and humidity while MERRA has no explicit consideration of irrigation at the surface. But, when compared with the results from a hydrological model with detailed considerations of agriculture, the ET from both reanalyses show large deficiencies in capturing the impact of irrigation. Here, a back-trajectory method is used to estimate the contribution of irrigation to precipitation over local and surrounding regions, using MERRA with observation-based corrections and added irrigation-caused ET increase from the hydrological model. Results show substantial contributions of irrigation to precipitation over heavily irrigated regions in Asia, but the precipitation increase is much less than the ET increase over most areas, indicating that irrigation could lead to water deficits over these regions. For the same increase in ET, precipitation increases are larger over wetter areas where convection is more easily triggered, but the percentage increase in precipitation is similar for different areas. There are substantial regional differences in the patterns of irrigation impact, but, for all the studied regions, the highest percentage contribution to precipitation is over local land.

  12. Online decision support system for surface irrigation management

    Science.gov (United States)

    Wang, Wenchao; Cui, Yuanlai

    2017-04-01

    Zhanghe Irrigation District (Center China) to manage the required irrigation deliveries. Two years' application indicates that the proposed OIDSS can achieve promising performance for surface irrigation. Historical data of rice growing period in 2014 has been applied to test the OIDSS: it gives out 3 irrigation decisions, which is consistent with actual irrigation times and the forecast irrigation dates are well fit with the actual situations; the corresponding amount of total irrigation decreases by 15.13% compared to those without using the OIDSS.

  13. Application of safeguards techniques to the Eurodif gas diffusion plant

    International Nuclear Information System (INIS)

    Coates, J.H.; Goens, J.R.

    1979-01-01

    The characteristic features of gas diffusion plants are such that safeguards procedures specifically suited for this technique can be proposed. The first of these features is the fact that appreciably altering the enrichment level of the plant product is not possible without making easily detectable changes either in the plant structure itself or in the movement of incoming and outgoing materials. Furthermore, because of the size of gas diffusion plants large stocks of uranium are present in them. Although inventory differences may be small in relative terms, they are large in abosolute terms and exceed the quantities of low-enriched uranium considered significant from the standpoint of safeguards. Lastly, the impossibility for economic reasons for taking a physical inventory of the plant after it has been emptied prevents a comparison of the physical inventory with the book inventory. It would therefore seem that the safeguarding of a gas diffusion plant should be focused on the movement of nuclear material between the plant and the outside world. The verification of inputs and outputs can be considered satisfactory from the safeguards standpoint as long as it is possible to make sure of the containment of the plant and of the surveillance for the purpose of preventing clandestine alterations of structure. The description of the Eurodif plant and the movement of materials planned there at present indicate that the application of such a safeguards technique to the plant should be acceptable to the competent authorities. For this purpose a monitoring area has been set aside in which the inspectors will be able to keep track of all movements between the outside world and the enrichment plant

  14. Development and application of the electrochemical etching technique

    International Nuclear Information System (INIS)

    Sanders, M.E.

    1984-07-01

    This report documents the advances achieved in the development and application of several etched damage track plastic dosimeters that can be used to measure dose-equivalent from neutrons with energies from thermal to 20 MeV. The project was initiated with the design of a rem-responding dosimeter that measured fast (> 1 MeV) neutron dose-equivalent as a function of the damage track density directly induced within the volume of polycarbonate foils amplified by electrochemical etching. Stillwagon (1978) adapted electrochemical etching of polycarbonate foils (ECEPF) to alpha dosimetry and used the technique to determine Pu-239 uptake in human bone. Su (1979) extended the usefulness of the ECEPF neutron dosimetry technique to encompass thermal neutron dose measurement. The thermal neutron dosimeter was composed of an external radiator tablet made of 7 LiF in contact with a polycarbonate foil and utilized the thermal neutron-induced 6 Li(n, α) 3 H reaction to give a dose-equivalent response as a function of alpha track density registered in the detector foil. An intermediate (1 eV-1 MeV) neutron dosimeter was developed and has been shown to give an approximately dose-equivalent response to neutrons with energies from 1 eV to 17 MeV. The intermediate neutron dosimeter consists of 6 LiF-Teflon/CR-39 Polymer foil assembly which is enclosed by a (Cd + In) neutron filter. The neutron dose-equivalent is measured as a variable function of the damage track density registered in the CR-39 detector foil due to alpha particles from the 1/v dependent 6 Li(n, α) 3 H reaction, recoil H, C, O nuclei from neutron-induced elastic scattering within the foil volume, and protons from the 6 Li(n, p) reaction for neutron energies above 2 MeV. 46 figs., 6 tabs

  15. The innovative application of surface geophysical techniques for remedial investigations

    Energy Technology Data Exchange (ETDEWEB)

    Saunders, W.R. [OYO Geospace, Fort Myers, FL (United States); Smith, S. [ICF Kaiser Engineers, Boston, MA (United States); Gilmore, P. [Fishbeck, Thomson, Carr and Huber, Aida, MI (United States); Cox, S. [Blasland, Bouck, and Lee, Edison, NJ (United States)

    1993-03-01

    When researchers are investigating potential subsurface contamination at hazardous waste landfills, the surface geophysical techniques they may use are often limited. Many geophysical surveys are concerned with areas next to and not directly within the landfill units. The highly variable properties of the materials within the landfill may result in geophysical data that are either difficult or impossible to interpret. Therefore, contamination at these sites may not be detected until substantial lateral migration away from the unit has occurred. In addition, because of the poor resolution of some techniques, the landfill as a whole must be considered as a source, where discrete disposal areas within landfill units may be the actual point sources of contaminants. In theory, if specific sources within the landfill are identified and isolated, then reduced time, effort, and expenditures will be required for remediation activities. In the summer of 1989, the Idaho National Engineering Laboratory (INEL) investigated a small potentially hazardous waste landfill to determine if contaminant hot spots could be identified within the landfill and to determine if significant vertical and lateral migration of contaminants was occurring away from these locations. Based on the present hydrogeologic conditions, researchers anticipated that subsurface flow would be primarily vertical, with the zone of saturation at a depth greater than 150 meters. This necessitated that the survey be performed, for the most part, directly on the capped portion of the landfill. Focused geophysical surveys conducted off the landfill would not have provided useful information concerning conditions directly beneath the landfill. This paper discusses the planning, application, and analysis of four combined sensing methods: two methods of electromagnetic induction [low induction (Em) and time domain (TEM)], ground penetrating radar (GPR), and soil gas.

  16. Application of positron annihilation techniques in non-destructive testing

    International Nuclear Information System (INIS)

    Zeng Hui; Chen Zhiqiang; Jiang Jing; Xue Xudong; Wu Yichu; Liang Jianping; Liu Xiangbing; Wang Rongshan

    2014-01-01

    Background: The investigation of the material damage state is very important for industrial application. Most mechanical damage starts with a change in the microstructure of the material. Positron annihilation techniques are very sensitive probes for detecting defects and damage on an atomic scale in materials, which are of great concern in the engineering applications. Additionally they are apparatus of non-destruction, high-sensitivity and easy-use. Purpose: Our goal is to develop a system to exploit new non-destructive testing (NDT) methods using positron annihilation spectroscopy, a powerful tool to detect vacancy-type defects and their chemical environment. Methods: A positron NDT system was designed and constructed by modifying the 'sandwich structure' of sample-source-sample in conventional Doppler broadening and positron lifetime spectrometers. Doppler broadening and positron lifetime spectra of a single sample can be measured and analyzed by subtracting the contribution of a reference sample. Results: The feasibility and reliability of positron NDT system have been tested by analyzing nondestructively deformation and damage caused by mechanical treatment or by irradiation of metal alloys. This system can be used for detecting defects and damage in thick or large-size samples, as well as for measuring the two-dimension distribution of defects in portable, sensitive, fast way. Conclusion: Positron NDT measurement shows changes in real atomic-scale defects prior to changes in the mechanical properties, which are detectable by other methods of NDT, such as ultrasonic testing and eddy current testing. This system can be developed for use in both the laboratory and field in the future. (authors)

  17. Application of gamma irradiation technique for the preservation of propolis

    International Nuclear Information System (INIS)

    Matsuda, Andrea Harumi

    2002-01-01

    Irradiation has been recognized as an efficient method for the reduction of deteriorating and pathogenic microorganisms in foods. Propolis is a resinous product made by bees from material processed by the bee's own metabolism and resins from plants. The aim of this work was the application of gamma irradiation technique for the preservation of propolis, because of its efficiency in the reduction of the microbial load. The changes on the total flavonoids content, phenolic compounds and other characteristics required for the qualification and characterization of Brazilian propolis were also analysed. Propolis samples from Juiz de Fora region, Minas Gerais, were irradiated in a 60 Co source, with doses from 0 to 10kGy for the microbiological analyses and 5.0, 7.0 and 10.0kGy for the physico-chemical analyses. The physico-chemical that have been made were: determination of total flavonoids content, semi-quantitative determination of phenolic compounds (artepelin-C, kempferol, chrysin, galangin and quercetin), dry matter analysis, humidity, ash content, mechanical mass and waxes. The ionizing radiation has shown to be efficient in the reduction of the microbial load. Total coliforms determination showed a great reduction with the dose of 3kGy and concerning mesophile aerobic bacteria a systematic reduction was observed, achieving values <10 UFC/g for the dose of 10kGy; similar results was obtained for molds and yeasts. Salmonella assays were negative for all samples. There was no significant alteration on total flavonoids contents nor on the composition of phenolic compounds as a consequence of radiation application at the assayed conditions. The complementary analyses of dry matter and humidity contents, ashes, mechanical mass and waxes did not shown changes after irradiation even with the maximum dose of 10kGy, remaining the results within the standards required by the Brazilian legislation. (author)

  18. Root Zone Sensors for Irrigation Management in Intensive Agriculture

    NARCIS (Netherlands)

    Pardossi, A.; Incrocci, L.; Incrocci, G.; Marlorgio, F.; Battista, P.; Bacci, L.; Rapi, B.; Marzialetti, P.; Hemming, J.; Balendonck, J.

    2009-01-01

    Crop irrigation uses more than 70% of the world’s water, and thus, improving irrigation efficiency is decisive to sustain the food demand from a fast-growing world population. This objective may be accomplished by cultivating more water-efficient crop species and/or through the application of

  19. Performance evaluation of a center pivot variable rate irrigation system

    Science.gov (United States)

    Variable Rate Irrigation (VRI) for center pivots offers potential to match specific application rates to non-uniform soil conditions along the length of the lateral. The benefit of such systems is influenced by the areal extent of these variations and the smallest scale to which the irrigation syste...

  20. An overview of soil water sensors for salinity & irrigation management

    Science.gov (United States)

    Irrigation water management has to do with the appropriate application of water to soils, in terms of amounts, rates, and timing to satisfy crop water demands while protecting the soil and water resources from degradation. Accurate irrigation management is even more important in salt affected soils ...

  1. Comparative study of irrigation water use and groundwater recharge under various irrigation schemes in an agricultural region, central Taiwan

    Science.gov (United States)

    Chen, Shih-Kai; Jang, Cheng-Shin; Tsai, Cheng-Bin

    2016-04-01

    The risk of rice production has increased notably due to climate change in Taiwan. To respond to growing agricultural water shortage without affecting normal food production in the future, the application of water-saving irrigation will be a substantial resolution. However, the adoption of water-saving irrigation may result in the reducing of groundwater recharge because continuous flooding in the paddy fields could be regarded as an important source for groundwater recharge. The aim of this study was to evaluate the irrigation water-saving benefit and groundwater recharge deficit when adopting the System of Rice Intensification, known as SRI methodology, in the Choushui River alluvial fan (the largest groundwater pumping and the most important rice-cropping region in central Taiwan). The three-dimensional finite element groundwater model, FEMWATER, was applied to simulate the infiltration process and groundwater recharge under SRI methodology and traditional irrigation schemes including continuous irrigation, and rotational irrigation in two rice-crop periods with hydro-climatic data of 2013. The irrigation water use was then calculated by water balance. The results showed that groundwater recharge amount of SRI methodology was slightly lower than those of traditional irrigation schemes, reduced 3.6% and 1.6% in the first crop period, and reduced 3.2% and 1.6% in the second crop period, compared with continuous irrigation and rotational irrigation, respectively. However, the SRI methodology achieved notably water-saving benefit compared to the disadvantage of reducing the groundwater recharge amount. The field irrigation requirement amount of SRI methodology was significantly lower than those of traditional irrigation schemes, saving 37% and 20% of irrigation water in the first crop period, and saving 53% and 35% in the second crop period, compared with continuous irrigation and rotational irrigation, respectively. Therefore, the amount of groundwater pumping for

  2. MR angiography of the body. Technique and clinical applications

    Energy Technology Data Exchange (ETDEWEB)

    Neri, Emanuele [Pisa Univ. Radiodiagnostica 1 Universitaria (Italy). Diagnostic and Interventional Radiology Dept. of Oncology, Transplants, and Advanced Technologies in Medicine; Cosottini, Mirco [Pisa Univ. (Italy). Unit of Neuroradiology Dept. of Neurosciences; Caramella, Davide (eds.) [Pisa Univ. (Italy). Diagnostic and Interventional Radiology Dept. of Oncology, Transplants, and Advanced Technologies in Medicine

    2010-07-01

    Magnetic resonance angiography (MRA) continues to undergo exciting technological advances that are rapidly being translated into clinical practice. It also has evident advantages over other imaging modalities, including better patient safety compared with CT angiography and superior accuracy and contrast resolution compared with ultrasonography. With the aid of numerous high-quality illustrations, this book reviews the current role of MRA of the body. It is divided into three sections. The first section is devoted to issues relating to image acquisition technique and sequences. Individual chapters focus on flow-based MRA, contrast media, contrast-enhanced MRA, artifacts, and image processing. The second and principal section of the book addresses the clinical applications of MRA in various parts of the body, including the neck vessels, the spine, the thoracic aorta and pulmonary vessels, the heart and coronary arteries, the abdominal aorta and renal arteries, and peripheral vessels. The role of the blood pool contrast agents for the diagnosis and characterization of vascular disease is fully explored. The final section considers the role of MRA in patients undergoing liver or pancreas and kidney transplantation. This book will be an invaluable aid to all radiologists who work with MRA. (orig.)

  3. Process mining techniques: an application to time management

    Science.gov (United States)

    Khowaja, Ali Raza

    2018-04-01

    In an environment people have to make sure that all of their work are completed within a given time in accordance with its quality. In order to achieve the real phenomenon of process mining one needs to understand all of these processes in a detailed manner. Personal Information and communication has always been a highlighting issue on internet but for now information and communication tools within factual life refers to their daily schedule, location analysis, environmental analysis and, more generally, social media applications support these systems which makes data available for data analysis generated through event logs, but also for process analysis which combines environmental and location analysis. Process mining can be used to exploit all these real live processes with the help of the event logs which are already available in those datasets through user censored data or may be user labeled data. These processes could be used to redesign a user's flow and understand all these processes in a bit more detailed manner. In order to increase the quality of each of the processes that we go through our daily lives is to give a closer look to each of the processes and after analyzing them, one should make changes to get better results. On the contrarily, we applied process mining techniques on seven different subjects combined in a single dataset collected from Korea. Above all, the following paper comments on the efficiency of processes in the event logs referring to time management's sphere of influence.

  4. Exploring Gamification Techniques and Applications for Sustainable Tourism

    Directory of Open Access Journals (Sweden)

    Adina Letiţia Negruşa

    2015-08-01

    Full Text Available Tourism is perceived as an appropriate solution for pursuing sustainable economic growth due to its main characteristics. In the context of sustainable tourism, gamification can act as an interface between tourists (clients, organisations (companies, NGOs, public institutions and community, an interface built in a responsible and ethical way. The main objective of this study is to identify gamification techniques and applications used by organisations in the hospitality and tourism industry to improve their sustainable activities. The first part of the paper examines the relationship between gamification and sustainability, highlighting the links between these two concepts. The second part identifies success stories of gamification applied in hospitality and tourism and reviews gamification benefits by analysing the relationship between tourism organisations and three main tourism stakeholders: tourists, tourism employees and local community. The analysis is made in connection with the main pillars of sustainability: economic, social and environmental. This study is positioning the role of gamification in the tourism and hospitality industry and further, into the larger context of sustainable development.

  5. Risk-based maintenance-Techniques and applications

    International Nuclear Information System (INIS)

    Arunraj, N.S.; Maiti, J.

    2007-01-01

    Plant and equipment, however well designed, will not remain safe or reliable if it is not maintained. The general objective of the maintenance process is to make use of the knowledge of failures and accidents to achieve the possible safety with the lowest possible cost. The concept of risk-based maintenance was developed to inspect the high-risk components usually with greater frequency and thoroughness and to maintain in a greater manner, to achieve tolerable risk criteria. Risk-based maintenance methodology provides a tool for maintenance planning and decision making to reduce the probability of failure of equipment and the consequences of failure. In this paper, the risk analysis and risk-based maintenance methodologies were identified and classified into suitable classes. The factors affecting the quality of risk analysis were identified and analyzed. The applications, input data and output data were studied to understand their functioning and efficiency. The review showed that there is no unique way to perform risk analysis and risk-based maintenance. The use of suitable techniques and methodologies, careful investigation during the risk analysis phase, and its detailed and structured results are necessary to make proper risk-based maintenance decisions

  6. Application of simulation techniques in the probabilistic fracture mechanics

    International Nuclear Information System (INIS)

    De Ruyter van Steveninck, J.L.

    1995-03-01

    The Monte Carlo simulation is applied on a model of the fracture mechanics in order to assess the applicability of this simulation technique in the probabilistic fracture mechanics. By means of the fracture mechanics model the brittle fracture of a steel container or pipe with defects can be predicted. By means of the Monte Carlo simulation also the uncertainty regarding failures can be determined. Based on the variations in the toughness of the fracture and the defect dimensions the distribution of the chance of failure is determined. Also attention is paid to the impact of dependency between uncertain variables. Furthermore, the influence of the applied distributions of the uncertain variables and non-destructive survey on the chance of failure is analyzed. The Monte Carlo simulation results agree quite well with the results of other methods from the probabilistic fracture mechanics. If an analytic expression can be found for the chance of failure, it is possible to determine the variation of the chance of failure, next to an estimation of the chance of failure. It also appears that the dependency between the uncertain variables has a large impact on the chance of failure. It is also concluded from the simulation that the chance of failure strongly depends on the crack depth, and therefore of the distribution of the crack depth. 15 figs., 7 tabs., 12 refs

  7. Applications of nuclear analytical techniques to environmental studies

    International Nuclear Information System (INIS)

    Freitas, M.C.; Marques, A.P.; Reis, M.A.; Pacheco, A.M.G.; Barros, L.I.C.

    2001-01-01

    A few examples of application of nuclear-analytical techniques to biological monitors - natives and transplants - are given herein. Parmelia sulcata Taylor transplants were set up in a heavily industrialized area of Portugal - the Setubal peninsula, about 50 km south of Lisbon - where indigenous lichens are rare. The whole area was 10x15 km around an oil-fired power station, and a 2.5x2.5 km grid was used. In north-western Portugal, native thalli of the same epiphytes (Parmelia spp., mostly Parmelia sulcata Taylor) and bark from olive trees (Olea europaea) were sampled across an area of 50x50 km, using a 10x10 km grid. This area is densely populated and features a blend of rural, urban-industrial and coastal environments, together with the country's second-largest metro area (Porto). All biomonitors have been analyzed by INAA and PIXE. Results were put through nonparametric tests and factor analysis for trend significance and emission sources, respectively

  8. Applications of Information and Communication Technology for Improvements of Water and Soil Monitoring and Assessments in Agricultural Areas—A Case Study in the Taoyuan Irrigation District

    Directory of Open Access Journals (Sweden)

    Yu-Pin Lin

    2017-01-01

    Full Text Available In order to guarantee high-quality agricultural products and food safety, efforts must be made to manage and maintain healthy agricultural environments under the myriad of risks that they face. Three central system components of sustainable agricultural management schemes are real-time monitoring, decision-making, and remote access. Information and Communications Technology (ICT systems are a convenient means of providing both these and other functions, such as wireless sensor networking, mobile phone applications, etc., to agricultural management schemes. ICT systems have significantly improved in recent years and have been widely used in many fields, including environmental monitoring and management. Moreover, ICT could benefit agricultural environment management by providing a platform for collaboration between researchers and stakeholders, thereby improving agricultural practices and environments. This article reviews and discusses the way in which ICT can efficiently improve monitoring systems and risk assessments of agricultural environment monitoring, as well as the technological and methodological improvements of ICT systems. Finally, we develop and apply an ICT system, referred to as the agricultural environment protection system—comprised of a cloud, six E-platforms, three mobile devices, automatic monitoring devices, indigenous wireless sensor nodes, and gateways in agricultural networks—to a case study in the Taoyuan irrigation district, which acts as a pilot area in Taiwan. Through the system, we use all available information from the interdisciplinary structured cloud database to classify the focal area into different agricultural environmental risk zones. We also conducted further analysis based on a hierarchical approach in order to classify the agricultural environments in the study area, to allocate additional sampling with resin packages and mobile devices, as well as to assist decision makers and stakeholders. The main

  9. Contribution to the improvement of irrigation management practices through water - deficit irrigation

    International Nuclear Information System (INIS)

    Bazza, M.

    1995-01-01

    The study aimed at identifying irrigation management practices which could result in water savings through -water deficit irrigation. Two field experiments, one on wheat and the other on sugar beet, were conducted and consisted of refraining from supplying water during specific stages of the cycle so as to identy the period(s) during which water deficit would have a limited effect on crop production. In the case of wheat, high water deficit occurred during the early and during these stages was the most beneficial for the crop. However, one water application during the tillering stage allowed the yield to be lower only to that of the treatement with three irrigations. Irrigation during the stage of grain filling caused the kernel weight to be as high as under three irrigations. The lowest value corresponded to the treatement with one irrigation during grain filling and that under rainfed conditions. For sugar beet, when water stress was was applied early in the crop cycle, its effect could be almost entirely recovered with adequate watering during the rest of the growing season. On the opposite, good watering early in cycle, followed by a stress, resulted in the second lowest yield. Water deficit during the maturity stage had also a limited effect on yield. The most crucial periods for adequate watering were which correspond to late filiar development and root growth which coincided with the highest water requirements period. For the same amount of water savings through deficit irrigation, it was better to partition the stress throughout the cycle than during the critical stages of the crop. However, at the national level, it would have been more important to practice deficit irrigation and the irrigated area. For both crops, high yields as high as water - use efficiency values could have been obtained. 8 tabs; 5 refs ( Author )

  10. Prospective controlled trial comparing colostomy irrigation with "spontaneous-action" method.

    OpenAIRE

    Williams, N S; Johnston, D

    1980-01-01

    Thirty randomly selected patients with permanent colostomies entered a prospective controlled trial comparing colostomy irrigation with spontaneous action. Each patient was interviewed and examined before irrigation was begun and again after the technique had been used for three months. Each then reverted to spontaneous action for a further three months and was then reassessed. Eight patients abandoned irrigation and 22 (73%) adhered to the protocol. Irrigation caused no mishaps or complicati...

  11. A Fuzzy analytical hierarchy process approach in irrigation networks maintenance

    Science.gov (United States)

    Riza Permana, Angga; Rintis Hadiani, Rr.; Syafi'i

    2017-11-01

    Ponorogo Regency has 440 Irrigation Area with a total area of 17,950 Ha. Due to the limited budget and lack of maintenance cause decreased function on the irrigation. The aim of this study is to make an appropriate system to determine the indices weighted of the rank prioritization criteria for irrigation network maintenance using a fuzzy-based methodology. The criteria that are used such as the physical condition of irrigation networks, area of service, estimated maintenance cost, and efficiency of irrigation water distribution. 26 experts in the field of water resources in the Dinas Pekerjaan Umum were asked to fill out the questionnaire, and the result will be used as a benchmark to determine the rank of irrigation network maintenance priority. The results demonstrate that the physical condition of irrigation networks criterion (W1) = 0,279 has the greatest impact on the assessment process. The area of service (W2) = 0,270, efficiency of irrigation water distribution (W4) = 0,249, and estimated maintenance cost (W3) = 0,202 criteria rank next in effectiveness, respectively. The proposed methodology deals with uncertainty and vague data using triangular fuzzy numbers, and, moreover, it provides a comprehensive decision-making technique to assess maintenance priority on irrigation network.

  12. Two applications of airtightness control techniques on big assemblies

    CERN Document Server

    Devallan, C; Marcellin, J

    1973-01-01

    Deals with two airtightness control techniques respectively applied on intersecting storage rings (ISR) at CERN in Geneva and on a liquid methane storage tank. These two big assemblies called for two different control techniques which use helium and ammonia respectively as tracer gas. Existing practical leakage detection techniques to meet industrial needs are discussed at the end of the article. (2 refs).

  13. Innovative application of virtual display technique in virtual museum

    Science.gov (United States)

    Zhang, Jiankang

    2017-09-01

    Virtual museum refers to display and simulate the functions of real museum on the Internet in the form of 3 Dimensions virtual reality by applying interactive programs. Based on Virtual Reality Modeling Language, virtual museum building and its effective interaction with the offline museum lie in making full use of 3 Dimensions panorama technique, virtual reality technique and augmented reality technique, and innovatively taking advantages of dynamic environment modeling technique, real-time 3 Dimensions graphics generating technique, system integration technique and other key virtual reality techniques to make sure the overall design of virtual museum.3 Dimensions panorama technique, also known as panoramic photography or virtual reality, is a technique based on static images of the reality. Virtual reality technique is a kind of computer simulation system which can create and experience the interactive 3 Dimensions dynamic visual world. Augmented reality, also known as mixed reality, is a technique which simulates and mixes the information (visual, sound, taste, touch, etc.) that is difficult for human to experience in reality. These technologies make virtual museum come true. It will not only bring better experience and convenience to the public, but also be conducive to improve the influence and cultural functions of the real museum.

  14. Modelling of 3D fractured geological systems - technique and application

    Science.gov (United States)

    Cacace, M.; Scheck-Wenderoth, M.; Cherubini, Y.; Kaiser, B. O.; Bloecher, G.

    2011-12-01

    All rocks in the earth's crust are fractured to some extent. Faults and fractures are important in different scientific and industry fields comprising engineering, geotechnical and hydrogeological applications. Many petroleum, gas and geothermal and water supply reservoirs form in faulted and fractured geological systems. Additionally, faults and fractures may control the transport of chemical contaminants into and through the subsurface. Depending on their origin and orientation with respect to the recent and palaeo stress field as well as on the overall kinematics of chemical processes occurring within them, faults and fractures can act either as hydraulic conductors providing preferential pathways for fluid to flow or as barriers preventing flow across them. The main challenge in modelling processes occurring in fractured rocks is related to the way of describing the heterogeneities of such geological systems. Flow paths are controlled by the geometry of faults and their open void space. To correctly simulate these processes an adequate 3D mesh is a basic requirement. Unfortunately, the representation of realistic 3D geological environments is limited by the complexity of embedded fracture networks often resulting in oversimplified models of the natural system. A technical description of an improved method to integrate generic dipping structures (representing faults and fractures) into a 3D porous medium is out forward. The automated mesh generation algorithm is composed of various existing routines from computational geometry (e.g. 2D-3D projection, interpolation, intersection, convex hull calculation) and meshing (e.g. triangulation in 2D and tetrahedralization in 3D). All routines have been combined in an automated software framework and the robustness of the approach has been tested and verified. These techniques and methods can be applied for fractured porous media including fault systems and therefore found wide applications in different geo-energy related

  15. Hard x-ray phase contrastmicroscopy - techniques and applications

    Science.gov (United States)

    Holzner, Christian

    In 1918, Einstein provided the first description of the nature of the refractive index for X-rays, showing that phase contrast effects are significant. A century later, most x-ray microscopy and nearly all medical imaging remains based on absorption contrast, even though phase contrast offers orders of magnitude improvements in contrast and reduced radiation exposure at multi-keV x-ray energies. The work presented is concerned with developing practical and quantitative methods of phase contrast for x-ray microscopy. A theoretical framework for imaging in phase contrast is put forward; this is used to obtain quantitative images in a scanning microscope using a segmented detector, and to correct for artifacts in a commercial phase contrast x-ray nano-tomography system. The principle of reciprocity between scanning and full-field microscopes is then used to arrive at a novel solution: Zernike contrast in a scanning microscope. These approaches are compared on a theoretical and experimental basis in direct connection with applications using multi-keV x-ray microscopes at the Advanced Photon Source at Argonne National Laboratory. Phase contrast provides the best means to image mass and ultrastructure of light elements that mainly constitute biological matter, while stimulated x-ray fluorescence provides high sensitivity for studies of the distribution of heavier trace elements, such as metals. These approaches are combined in a complementary way to yield quantitative maps of elemental concentration from 2D images, with elements placed in their ultrastructural context. The combination of x-ray fluorescence and phase contrast poses an ideal match for routine, high resolution tomographic imaging of biological samples in the future. The presented techniques and demonstration experiments will help pave the way for this development.

  16. Application of integrated data mining techniques in stock market forecasting

    Directory of Open Access Journals (Sweden)

    Chin-Yin Huang

    2014-12-01

    Full Text Available Stock market is considered too uncertain to be predictable. Many individuals have developed methodologies or models to increase the probability of making a profit in their stock investment. The overall hit rates of these methodologies and models are generally too low to be practical for real-world application. One of the major reasons is the huge fluctuation of the market. Therefore, the current research focuses in the stock forecasting area is to improve the accuracy of stock trading forecast. This paper introduces a system that addresses the particular need. The system integrates various data mining techniques and supports the decision-making for stock trades. The proposed system embeds the top-down trading theory, artificial neural network theory, technical analysis, dynamic time series theory, and Bayesian probability theory. To experimentally examine the trading return of the presented system, two examples are studied. The first uses the Taiwan Semiconductor Manufacturing Company (TSMC data-set that covers an investment horizon of 240 trading days from 16 February 2011 to 23 January 2013. Eighty four transactions were made using the proposed approach and the investment return of the portfolio was 54% with an 80.4% hit rate during a 12-month period in which the TSMC stock price increased by 25% (from $NT 78.5 to $NT 101.5. The second example examines the stock data of Evergreen Marine Corporation, an international marine shipping company. Sixty four transactions were made and the investment return of the portfolio was 128% in 12 months. Given the remarkable investment returns in trading the example TSMC and Evergreen stocks, the proposed system demonstrates promising potentials as a viable tool for stock market forecasting.

  17. Estimating the Effects of Conversion of Agricultural Land to Urban Land on Deep Percolation of Irrigation Water in the Grand Valley, Western Colorado

    Science.gov (United States)

    Mayo, John W.

    2008-01-01

    The conversion of agricultural land to urban residential land is associated with rapid population growth in the Grand Valley of western Colorado. Information regarding the effects of this land-use conversion on deep percolation, irrigation-water application, and associated salt loading to the Colorado River is needed to support water-resource planning and conservation efforts. The Natural Resources Conservation Service (NRCS) assessed deep percolation and estimated salt loading derived from irrigated agricultural lands in the Grand Valley in a 1985 to 2002 monitoring and evaluation study (NRCS M&E). The U.S. Geological Survey (USGS), in cooperation with the Colorado River Salinity Control Forum and the Mesa Conservation District, quantified the current (2005-2006) deep percolation and irrigation-water application characteristics of 1/4-acre residential lots and 5-acre estates, urban parks, and urban orchard grass fields in the Grand Valley, and compared the results to NRCS M&E results from alfalfa-crop sites. In addition, pond seepage from three irrigation-water holding ponds was estimated. Salt loading was estimated for the urban study results and the NRCS M&E results by using standard salt-loading factors. A daily soil-moisture balance calculation technique was used at all urban study irrigated sites. Deep percolation was defined as any water infiltrating below the top 12 inches of soil. Deep percolation occurred when the soil-moisture balance in the first 12 inches of soil exceeded the field capacity for the soil type at each site. Results were reported separately for urban study bluegrass-only sites and for all-vegetation type (bluegrass, native plants, and orchard grass) sites. Deep percolation and irrigation-water application also were estimated for a complete irrigation season at three subdivisions by using mean site data from each subdivision. It was estimated that for the three subdivisions, 37 percent of the developed acreage was irrigated (the balance

  18. Effect Of Soil Contamination Due To Wastewater Irrigation On Total Co As Determined By Neutron Activation And Other Conventional Analytical Techniques In Some Soils Of Egypt

    International Nuclear Information System (INIS)

    Abdel-Sabour, M. F.; Al-Salama, Y. J.

    2004-01-01

    Fifteen soil samples were chosen from different locations (five different locations at north greater Cairo, Egypt) to represent different soils (alluvial and sandy) as well as different sources of contaminated wastewater (sewage and industrial effluent). Using sequential extraction technique (extracting the soil with different solutions, which is designed to separate metal fractions), Co was separated into six operationally defined fractions: water soluble, exchangeable, carbonate bound, Fe-Mn oxides bound, organic bound and residual fractions. Moreover, total-Co in soils as determined by three analytical methods (sum of sequential extracting, Atomic Absorption Spectrometry (AAS) and neutron activation analysis (NAA) techniques) were compared. Cobalt distribution between different extractants shows that the greatest amounts are found in the residual and Occluded in Fe and Mn-Oxides fractions followed by carbonate or organic fractions. In most cases the proportion of all tested Co-forms has increased in contaminated soil layers with higher enrichment in organically bound Co, occluded in Fe and Mn oxides, carbonate exchangeable and soluble fractions. Results indicate that soil properties have a significant role on Co fractions in soil. In the mean time, soil properties are affected by pollution factors such as source of pollution and load of pollution on the studied soil. Data showed that values of total Co determined by NAA method were always higher than the relevant values determined by AAS or those calculated after the sequential extraction method. (Authors)

  19. Application of nuclear techniques in Poland; Perspektywy wykorzystania atomistyki w Polsce

    Energy Technology Data Exchange (ETDEWEB)

    Chmielewski, A.G.; Owczarczyk, A.; Urbanski, P. [Instytut Chemii i Techniki Jadrowej, Warsaw (Poland); Romanowski, M. [Biuro Studiow i Projektow Techniki Jadrowej `Proatom`, Warsaw (Poland); Stegowski, Z. [Akademia Gorniczo-Hutnicza, Cracow (Poland); Nowak, K. [Osrodek Badawczo-Rozwojowy Izotopow, Swierk-Otwock (Poland); Pachan, A. [Instytut Problemow Jadrowych, Swierk-Otwock (Poland); Tanczyk, R. [Centralne Laboratorium Ochrony Radiologicznej, Warsaw (Poland); Jablonski, R. [Zaklad Techniki Izotopowej `Polon-Izot`, Warsaw (Poland)

    1997-12-31

    The commercial applications of nuclear techniques in Poland have been presented. The special attention have been paid at: radiation technologies, application of radiometric gages in different branches of industry, tracer techniques, production and application of radiation sources in medicine, industry and material testing. 10 refs, 6 figs, 6 tabs.

  20. Drip irrigation using a PLC based adaptive irrigation system

    OpenAIRE

    Shahidian, S.; Serralheiro, R. P.; Teixeira, J. L.; Santos, F. L.; Oliveira, M. R. G.; Costa, J. L.; Toureiro, C.; Haie, Naim; Machado, R. M.

    2009-01-01

    Most of the water used by man goes to irrigation. A major part of this water is used to irrigate small plots where it is not feasible to implement full-scale Evapotranspiration based irrigation controllers. During the growth season crop water needs do not remain constant and varies depending on the canopy, growth stage and climate conditions such as temperature, wind, relative humidity and solar radiation. Thus, it is necessary to find an economic irrigation controller that can adapt the dail...

  1. Evolution of Corn Transpiration and Leaf Water Potential During Sprinkler Irrigation

    OpenAIRE

    Martínez-Cob, Antonio; Fernández-Navajas, Julián; Durán, Víctor; Cavero Campo, José

    2009-01-01

    Corn (Zea mays L.) transpiration during daytime solid-set sprinkler irrigation was analyzed on two neighbouring subplots to determine the effect of the transpiration reduction on water application efficiency. During each irrigation event, one subplot was irrigated (moist treatment) while the other was not (dry treatment). Transpiration rates were determined at each subplot by the heat balance method (Dynamax Flow4 System) before, during and after the irrigations. During irri...

  2. Smart Irrigation From Soil Moisture Forecast Using Satellite And Hydro -Meteorological Modelling

    Science.gov (United States)

    Corbari, Chiara; Mancini, Marco; Ravazzani, Giovanni; Ceppi, Alessandro; Salerno, Raffaele; Sobrino, Josè

    2017-04-01

    Increased water demand and climate change impacts have recently enhanced the need to improve water resources management, even in those areas which traditionally have an abundant supply of water. The highest consumption of water is devoted to irrigation for agricultural production, and so it is in this area that efforts have to be focused to study possible interventions. The SIM project funded by EU in the framework of the WaterWorks2014 - Water Joint Programming Initiative aims at developing an operational tool for real-time forecast of crops irrigation water requirements to support parsimonious water management and to optimize irrigation scheduling providing real-time and forecasted soil moisture behavior at high spatial and temporal resolutions with forecast horizons from few up to thirty days. This study discusses advances in coupling satellite driven soil water balance model and meteorological forecast as support for precision irrigation use comparing different case studies in Italy, in the Netherlands, in China and Spain, characterized by different climatic conditions, water availability, crop types and irrigation techniques and water distribution rules. Herein, the applications in two operative farms in vegetables production in the South of Italy where semi-arid climatic conditions holds, two maize fields in Northern Italy in a more water reach environment with flood irrigation will be presented. This system combines state of the art mathematical models and new technologies for environmental monitoring, merging ground observed data with Earth observations. Discussion on the methodology approach is presented, comparing for a reanalysis periods the forecast system outputs with observed soil moisture and crop water needs proving the reliability of the forecasting system and its benefits. The real-time visualization of the implemented system is also presented through web-dashboards.

  3. Zone edge effects with variable rate irrigation

    Science.gov (United States)

    Variable rate irrigation (VRI) systems may offer solutions to enhance water use efficiency by addressing variability within a field. However, the design of VRI systems should be considered to maximize application uniformity within sprinkler zones, while minimizing edge effects between such zones alo...

  4. The multiple applications of the nuclear techniques in Argentina

    International Nuclear Information System (INIS)

    Manzini, Alberto C.

    2001-01-01

    A review is given of the use of nuclear technology in Argentina, especially in the field of the production of radioisotopes and radiopharmaceuticals, nuclear medicine, and industrial applications. The applications of ionizing radiation are also reviewed

  5. Application of source biasing technique for energy efficient DECODER circuit design: memory array application

    Science.gov (United States)

    Gupta, Neha; Parihar, Priyanka; Neema, Vaibhav

    2018-04-01

    Researchers have proposed many circuit techniques to reduce leakage power dissipation in memory cells. If we want to reduce the overall power in the memory system, we have to work on the input circuitry of memory architecture i.e. row and column decoder. In this research work, low leakage power with a high speed row and column decoder for memory array application is designed and four new techniques are proposed. In this work, the comparison of cluster DECODER, body bias DECODER, source bias DECODER, and source coupling DECODER are designed and analyzed for memory array application. Simulation is performed for the comparative analysis of different DECODER design parameters at 180 nm GPDK technology file using the CADENCE tool. Simulation results show that the proposed source bias DECODER circuit technique decreases the leakage current by 99.92% and static energy by 99.92% at a supply voltage of 1.2 V. The proposed circuit also improves dynamic power dissipation by 5.69%, dynamic PDP/EDP 65.03% and delay 57.25% at 1.2 V supply voltage.

  6. Magnetic Resonance Microscopy Spatially Resolved NMR Techniques and Applications

    CERN Document Server

    Codd, Sarah

    2008-01-01

    This handbook and ready reference covers materials science applications as well as microfluidic, biomedical and dental applications and the monitoring of physicochemical processes. It includes the latest in hardware, methodology and applications of spatially resolved magnetic resonance, such as portable imaging and single-sided spectroscopy. For materials scientists, spectroscopists, chemists, physicists, and medicinal chemists.

  7. Irrigation port hydration in phacoemulsification surgery

    Directory of Open Access Journals (Sweden)

    Suzuki H

    2018-01-01

    Full Text Available Hisaharu Suzuki,1 Yoichiro Masuda,2 Yuki Hamajima,1 Hiroshi Takahashi3 1Department of Ophthalmology, Nippon Medical School Musashikosugi Hospital, Kawasaki City, Kanagawa, 2Department of Ophthalmology, The Jikei University, Katsushika Medical Center, Tokyo, 3Department of Ophthalmology, Nippon Medical School, Tokyo, Japan Background: In most cases, hydration is performed by water injection into the stromal tissue with a needle. The technique is simple, however it is sometimes troublesome.Purpose: We describe a simple technique for hydrating the corneal stroma in cataract surgery using an irrigation port.Patients and methods: The technique began by pushing the irrigation port against the corneal stroma for a few seconds during phacoemulsification, which generated edema in the corneal incision that subsequently prevented leakage. This procedure is called the hydration using irrigation port (HYUIP technique. A total of 60 eyes were randomized and placed in two groups, 30 eyes underwent surgeries using the HYUIP technique (HYUIP group and 30 eyes underwent surgeries without the HYUIP technique (control. The three points evaluated during each surgery included 1 the occurrence of anterior chamber collapse during the pulling out of the I/A tip after inserting the intraocular lens, 2 the need for conventional hydration, and 3 watertight completion at the end stage of surgery.Results: The anterior chamber collapse and the need for conventional hydration were significantly smaller in the HYUIP group compared to the control group. Regarding the self-sealing completion, no significant difference was observed between the two groups.Conclusion: The HYUIP technique is an effective method for creating self-sealing wound. In addition, this technique helps to prevent anterior chamber collapse. Keywords: cataract surgery, hydration, irrigation and aspiration, phacoemulsification, wound, self-sealing 

  8. Industrial applications of radioisotopes: techniques and procedures of (NTIS) Nuclear Techniques Industrial Service

    International Nuclear Information System (INIS)

    Smith, S.W.; Kruger, J.

    1985-06-01

    Radioisotope handling procedures followed by personnel of the Nuclear Techniques Industrial Service (NTIS) during the conduction of investigations in industry are described. Possible radiological implications as a result of the various measuring techniques and different types of plants are discussed. Conditions under which permanent authorization has been granted for the use of radioisotopes are mentioned

  9. Charts for Guiding Adjustments of Irrigation Interval to Actual Weather Conditions

    International Nuclear Information System (INIS)

    Kipkorir, E.C.

    2002-01-01

    Major problems in irrigation management at short time-step during the season are unreliability of rainfall and absence of guidance. By considering the climate of region, crop and soil characteristics, the irrigation method and local irrigation practices, this paper presents the concept of irrigation charts. The charts are based on soil water technique. As an example irrigation chart for a typical irrigation system located in the semi-arid area in Naivasha, Kenya is presented. The chart guides the user in adjustment of irrigation interval to the actual weather conditions throughout the growing season. It is believed that the simplicity of the chart makes it a useful tool for a better utilisation of the limited irrigation water

  10. Two biased estimation techniques in linear regression: Application to aircraft

    Science.gov (United States)

    Klein, Vladislav

    1988-01-01

    Several ways for detection and assessment of collinearity in measured data are discussed. Because data collinearity usually results in poor least squares estimates, two estimation techniques which can limit a damaging effect of collinearity are presented. These two techniques, the principal components regression and mixed estimation, belong to a class of biased estimation techniques. Detection and assessment of data collinearity and the two biased estimation techniques are demonstrated in two examples using flight test data from longitudinal maneuvers of an experimental aircraft. The eigensystem analysis and parameter variance decomposition appeared to be a promising tool for collinearity evaluation. The biased estimators had far better accuracy than the results from the ordinary least squares technique.

  11. Application of PSA techniques to synchrotron radiation source facilities

    International Nuclear Information System (INIS)

    Sanyasi Rao, V.V.S.; Vinod, G.; Vaze, K.K.; Sarkar, P.K.

    2011-01-01

    Synchrotron radiation sources are increasingly being used in research and medical applications. Various instances of overexposure in these facilities have been reported in literature. These instances have lead to the investigation of the risks associated with them with a view to minimise the risks and thereby increasing the level of safety. In nuclear industry, Probabilistic Safety Assessment (PSA) methods are widely used to assess the risk from nuclear power plants. PSA presents a systematic methodology to evaluate the likelihood of various accident scenarios and their possible consequences using fault/event tree techniques. It is proposed to extend similar approach to analyse the risk associated with synchrotron radiation sources. First step for such an analysis is establishing the failure criteria, considering the regulatory stipulations on acceptable limits of dose due to ionization radiation from normal as well as beam loss scenarios. Some possible scenarios considered in this study are (1) excessive Bremsstrahlung in the ring due to loss of vacuum, (2) Target failure due to excessively focused beam (3) mis-directed/mis-steered beam (4) beam loss and sky shine. Hazard analysis needs to cover the beam transfer line, storage ring and experimental beam line areas. Various safety provisions are in place to minimize the hazards from these facilities such as access control interlock systems, radiation shielding for storage ring and beam lines and safety shutters (for beam lines). Experimental beam line area is the most vulnerable locations that need to be critically analysed. There are multiple beam lines, that have different safety provisions and consequences from postulated beam strikes will also be different and this increases the complexity of analysis. Similar studies conducted for such experimental facilities have identified that the radiation safety interlock system, used to control access to areas inside ring and the hutches of beamline facilities has an

  12. The applications of nuclear techniques in nuclear medicine

    International Nuclear Information System (INIS)

    Zhao Huiyang

    1986-01-01

    There are a great deal of advanced techniques in nuclear medicine imaging, because many recent achivements of nuclear techniques have been applied to medicine in recent years. This paper presents the effects of nuclear techniques in development of nuclear medicine imaging. The first part describes radiopharmaceuticals and nuclear medicine imaging including commonly used 99m Tc labeled agents and cyclotron produced radionuclides for organ imaging. The second part describes nuclear medicine instrucments, including PECT, SPECT, MRI ect.; and discussions on the advantages, disadvantages and present status

  13. Passive RF component technology materials, techniques, and applications

    CERN Document Server

    Wang, Guoan

    2012-01-01

    Focusing on novel materials and techniques, this pioneering volume provides you with a solid understanding of the design and fabrication of smart RF passive components. You find comprehensive details on LCP, metal materials, ferrite materials, nano materials, high aspect ratio enabled materials, green materials for RFID, and silicon micromachining techniques. Moreover, this practical book offers expert guidance on how to apply these materials and techniques to design a wide range of cutting-edge RF passive components, from MEMS switch based tunable passives and 3D passives, to metamaterial-bas

  14. Application of pattern recognition techniques to crime analysis

    Energy Technology Data Exchange (ETDEWEB)

    Bender, C.F.; Cox, L.A. Jr.; Chappell, G.A.

    1976-08-15

    The initial goal was to evaluate the capabilities of current pattern recognition techniques when applied to existing computerized crime data. Performance was to be evaluated both in terms of the system's capability to predict crimes and to optimize police manpower allocation. A relation was sought to predict the crime's susceptibility to solution, based on knowledge of the crime type, location, time, etc. The preliminary results of this work are discussed. They indicate that automatic crime analysis involving pattern recognition techniques is feasible, and that efforts to determine optimum variables and techniques are warranted. 47 figures (RWR)

  15. Assessing the changes of groundwater recharge / irrigation water use between SRI and traditional irrigation schemes in Central Taiwan

    Science.gov (United States)

    Chen, Shih-Kai; Jang, Cheng-Shin; Tsai, Cheng-Bin

    2015-04-01

    To respond to agricultural water shortage impacted by climate change without affecting rice yield in the future, the application of water-saving irrigation, such as SRI methodology, is considered to be adopted in rice-cultivation in Taiwan. However, the flooded paddy fields could be considered as an important source of groundwater recharge in Central Taiwan. The water-saving benefit of this new methodology and its impact on the reducing of groundwater recharge should be integrally assessed in this area. The objective of this study was to evaluate the changes of groundwater recharge/ irrigation water use between the SRI and traditional irrigation schemes (continuous irrigation, rotational irrigation). An experimental paddy field located in the proximal area of the Choushui River alluvial fan (the largest groundwater pumping region in Taiwan) was chosen as the study area. The 3-D finite element groundwater model (FEMWATER) with the variable boundary condition analog functions, was applied in simulating groundwater recharge process and amount under traditional irrigation schemes and SRI methodology. The use of effective rainfall was taken into account or not in different simulation scenarios for each irrigation scheme. The simulation results showed that there were no significant variations of infiltration rate in the use of effective rainfall or not, but the low soil moisture setting in deep soil layers resulted in higher infiltration rate. Taking the use of effective rainfall into account, the average infiltration rate for continuous irrigation, rotational irrigation, and SRI methodology in the first crop season of 2013 were 4.04 mm/day, 4.00 mm/day and 3.92 mm/day, respectively. The groundwater recharge amount of SRI methodology was slightly lower than those of traditional irrigation schemes, reducing 4% and 2% compared with continuous irrigation and rotational irrigation, respectively. The field irrigation requirement amount of SRI methodology was significantly

  16. Application of microdialysis technique in the traditional chinese medicine

    DEFF Research Database (Denmark)

    Zhang, Shaomin; Zeng, Xianghui; Xu, Xiaohong

    2005-01-01

    The concentration of extracellular neurotransmitters can be dynamically measured by in vivo microdialysis. This technique can apply to quantitatively evaluating the beneficial effects of Traditional Chinese Medicine (TCM). In the present study, the protective effects of Puerarin (Pur) on cerebral...

  17. Application of the Sampling Selection Technique in Approaching Financial Audit

    Directory of Open Access Journals (Sweden)

    Victor Munteanu

    2018-03-01

    Full Text Available In his professional approach, the financial auditor has a wide range of working techniques, including selection techniques. They are applied depending on the nature of the information available to the financial auditor, the manner in which they are presented - paper or electronic format, and, last but not least, the time available. Several techniques are applied, successively or in parallel, to increase the safety of the expressed opinion and to provide the audit report with a solid basis of information. Sampling is used in the phase of control or clarification of the identified error. The main purpose is to corroborate or measure the degree of risk detected following a pertinent analysis. Since the auditor does not have time or means to thoroughly rebuild the information, the sampling technique can provide an effective response to the need for valorization.

  18. Application of adaptive neuro-fuzzy inference system technique in ...

    African Journals Online (AJOL)

    Journal of Agriculture, Science and Technology ... The recent explosion in information technology and wireless communications has created many opportunities ... This artificial Intelligence (AI) technique is used in determining the parameters ...

  19. Concept, characteristics, and applications of important electrical measuring techniques

    International Nuclear Information System (INIS)

    Amberg, C.; Czaika, N.; Andreae, G.

    1978-01-01

    In the field of electrical measuring techniques the investigations were concentrated on the transducers. We investigated the time-temperature behaviour of the following transducers: The weldable, fully encapsulated high temperature strain gauges, inductance and transformer displacement transducers, and weldable capacitive strain transducers with distance sensor. A literatur-review showing the state of techniques reference the influence of nuclear radiation was put together. (orig./HP) [de

  20. Study of the technical performance of localized irrigation and its environmental and agroeconomic impact in the first areas of collective reconversion at the irrigated perimeter of the Tadla - Beni Moussa perimeter of the west - Morocco

    Science.gov (United States)

    Mouradi, Abdellah; Ait Yacine, Zehor; El Harti, Abderrazak

    2018-05-01

    The evaluation of the performance of the localized irrigation system involved a selected sample of farmers to reflect the diversity of the study area. The hydraulic diagnosis revealed the absence of apparent malfunctioning anomalies of the installations studied (Coefficient of Distribution Uniformity ≥ 90% with average application efficiencies and overall of 90.54 and 86.83% respectively). In terms of the combined use of surface and underground irrigation water this new technique has saved about 30% compared to conventional irrigation. The agro-economic evaluation revealed that the crops practiced have high value-added and optimize the value of irrigation water. The environmental impact has resulted in an average drawdown of the static level of groundwater of 2.59 m due mainly to the new irrigation method introduced, which limited the percolation of water to the aquifer. The drip-to-drip transition resulted in an increase in salinity relative compared to the reference situation (+ 0.59 %, or 0.01 mS / cm) but to different degrees depending on the prospecting soil horizon. The practice of fertilization remains the major and probable cause of soil salinization of aquifers. The effect of soluble salts on the soil was investigated through the risks associated with sodium, which showed that the soil permeability problem does not arise at this time (SAR ≤ 15). The residual sodium carbonate remains less than 1.25 meq / l thus not causing soil dispersion.

  1. Effect of different levels of nitrogen fertilizer on yield and quality of sugar beet Beta vulgaris irrigated with saline groundwater (fertigation and surface irrigation) and grown under saline conditions

    International Nuclear Information System (INIS)

    Janat, M.

    2009-07-01

    In a field experiment Sugar beet Beta vulgaris was grown as a spring crop during the growing seasons of 2004 and 2006, in salt affected soil, previously planted with sesbania and barley (2005 and 2003) to evaluate the response of sugar beet to two irrigation methods, (drip fertigation and surface irrigation), different levels of nitrogen fertilizer and its effect on yield and quality. Different rates of nitrogen fertilizers (0, 50, 100, 150 and 200 kg N/ ha) as urea (46% N) were injected for drip irrigation or broadcasted for the surface-irrigated treatments in four equally split applications. The 15 N labelled urea was applied to sub-plots of 1.0 m 2 in each experimental unit in a manner similar to that of unlabeled urea. Irrigation scheduling was carried out using the direct method of neutron scattering technique. Sugar beet was irrigated when soil moisture in the upper 25 cm was 80% of the field capacity (FC) and such practice continued until the six leaf stage. From the latter stage until harvest, sugar beet was irrigated when soil moisture in the upper 50 cm reached 80% of the FC. The amount of irrigation water applied, electrical conductivity of the soil paste, dry matter and fresh roots yield, total nitrogen uptake and N derived from fertilizer were also determined. Furthermore, Nitrogen use as well as water use-efficiencies for dry matter and roots yield were also calculated. Results revealed that sugar beets and dry matter yield increased with increasing N input up to 100-150 kg N/ha which was indicated by the higher dry matter yield, and sugar beet yield. Sugar percentage was also increased relative to the average percentage recorded in Syria. Crop water use efficiencies, for both the drip-fertigated and surface-irrigated treatments were increased in most cases with increasing rate of nitrogen fertilizer. During the course of this study, small increases in soil salinity under both irrigation methods were observed. Higher increases in soil salinity was

  2. Chemical dosimetry techniques for various applications under different geometries

    CERN Document Server

    Gupta, B L; Narayan, G R; Nilekani, S R

    2000-01-01

    This paper gives the results of dosimetry for various applications under different geometrical arrangements. These applications include: gamma chambers, blood irradiators, radiotherapy using both sup 6 sup 0 Co and accelerators, animal irradiations with different types of radiation sources, fluid irradiators for sludge and rubber latex and industrial electron irradiators. The dosimeters used were Fricke, FBX and alanine/glutamine (spectrophotometric readout).

  3. Application of a sex identification technique in juvenile ostriches and ...

    African Journals Online (AJOL)

    DNA-based sex identification provides a solution and is amenable to large-scale application. The application of the multiplex polymerase chain reaction (PCR) was used to determine the sex of 6-months old juvenile ostriches. The blood from four mature males and four mature females were used to verify the assay. The test ...

  4. Irrigation and fertigation frequencies with nitrogen in the watermelon culture

    Directory of Open Access Journals (Sweden)

    Carlos Newdmar Vieira Fernandes

    2014-06-01

    Full Text Available This study evaluates the influence of different irrigation frequencies and different nitrogen fertigation frequencies on the growth performance of the watermelon (Citrullus lanatus culture. Two experiments were conducted at the Paraguay farm in the Cruz municipality, Ceará, Brazil. They was randomized blocks design with six treatments and four replications. The irrigation frequency experiment consisted of the application of different irrigation frequencies. The treatments were: DM - daily irrigation in the morning with 100% daily dosage; DT - daily irrigation in the afternoon, with 100% daily dosage; DMT - twice daily irrigation, with 50% daily dosage in the morning and 50% daily dosage in the afternoon; 2D - irrigation every two days; 3D - irrigation every three days and 4D - irrigation every four days. To the experiment with different nitrogen fertigation frequencies, the treatments used were: 2F - 2 fertigations in a cycle; 4F - 4 fertigations in a cycle; 8F - 8 fertigations in a cycle; 16F - 16 fertigations in a cycle; 32F - 32 fertigations in a cycle and 64F - 64 fertigations in a cycle. We evaluated the marketable yield (PC, fruit weight (M, polar diameter (DP, equatorial diameter (DE, shell thickness (EC and soluble solids (SS. The irrigation frequency treatments influenced all variables significantly, with twice daily irrigation (DMT, 50% in the morning and the 50% in the afternoon promoting the highest productivity (69.79 t ha-1. The different frequencies of fertigation also significantly influenced all variables, except for the shell thickness, the highest yield (80.69 t ha-1 being obtained with treatment 64 fertigations in a cycle.

  5. Deficit irrigation strategies

    DEFF Research Database (Denmark)

    Stikic, Radmilla; Savíc, Sladjana; Jovanovic, Zorica

    2010-01-01

    Book Description: Horticulture is the industry and science of plant cultivation, including the process of preparing soil for the planting of seeds, tubers, or cuttings. Horticulturists work and conduct research in the disciplines of plant propagation and cultivation, crop production, plant breeding...... grafting techniques at the seedling stage to overcome soil-borne diseases, the application of biotechnology tools in the conservation of critically endangered plant species, salinity tolerance of ornamental horticultural species, and others....

  6. Increasing water productivity, nitrogen economy, and grain yield of rice by water saving irrigation and fertilizer-N management.

    Science.gov (United States)

    Aziz, Omar; Hussain, Saddam; Rizwan, Muhammad; Riaz, Muhammad; Bashir, Saqib; Lin, Lirong; Mehmood, Sajid; Imran, Muhammad; Yaseen, Rizwan; Lu, Guoan

    2018-06-01

    The looming water resources worldwide necessitate the development of water-saving technologies in rice production. An open greenhouse experiment was conducted on rice during the summer season of 2016 at Huazhong Agricultural University, Wuhan, China, in order to study the influence of irrigation methods and nitrogen (N) inputs on water productivity, N economy, and grain yield of rice. Two irrigation methods, viz. conventional irrigation (CI) and "thin-shallow-moist-dry" irrigation (TSMDI), and three levels of nitrogen, viz. 0 kg N ha -1 (N 0 ), 90 kg N ha -1 (N 1 ), and 180 kg N ha -1 (N 2 ), were examined with three replications. Study data indicated that no significant water by nitrogen interaction on grain yield, biomass, water productivity, N uptake, NUE, and fertilizer N balance was observed. Results revealed that TSMDI method showed significantly higher water productivity and irrigation water applications were reduced by 17.49% in TSMDI compared to CI. Thus, TSMDI enhanced root growth and offered significantly greater water saving along with getting more grain yield compared to CI. Nitrogen tracer ( 15 N) technique accurately assessed the absorption and distribution of added N in the soil crop environment and divulge higher nitrogen use efficiency (NUE) influenced by TSMDI. At the same N inputs, the TSMDI was the optimal method to minimize nitrogen leaching loss by decreasing water leakage about 18.63%, which are beneficial for the ecological environment.

  7. Nuclear analytical techniques and applications to materials processing

    International Nuclear Information System (INIS)

    Blondiaux, G.; Debrun, J.L.

    1993-01-01

    This paper will present the application of Rutherford backscattering spectrometry to thin film steochiometry determination and application to optimization of the film process elaboration in the case of dielectric films (Ge,Pb,O) and ionic conductors films (Na,Al,O). After we shall present the application of particles induced gamma emission (PIGE) for the characterization of ternary compounds (B,Si,C) used as coating to protect composites materials. The last part of this paper will describe the determination of oxygen in the bulk of fluoride glasses with charged particles activation analysis. (orig.)

  8. Radiation safety in industrial applications of nuclear techniques

    International Nuclear Information System (INIS)

    Lam, E.S.

    1981-01-01

    The hazards associated with the use of industrial equipment is one of the undesirable by-products of advanced technology. The use of nuclear techniques is a good example. Due to the usefulness of such techniques, one may accept the risks involved if they can be brought down to manageable levels. Most of the nuclear techniques in use in industries in Malaysia require only minimal safety precautions as they make use of only small amounts of radioactive material. However, some large sources are also being used and safety precautions have to be strictly enforced. The management plays a critical role in these industries. The requirements for radiation safety include the monitoring of workers and work areas, the medical surveillance of workers and the provision of barriers and other safety precautions. The management should also look to the training of the workers and be prepared for any emergencies that may arise. (author)

  9. Radiation safety in industrial applications of nuclear techniques

    Energy Technology Data Exchange (ETDEWEB)

    Lam, E S [Ministry of Health, Kuala Lumpur (Malaysia)

    1981-01-01

    The hazards associated with the use of industrial equipment is one of the undesirable by-products of advanced technology. The use of nuclear techniques is a good example. Due to the usefulness of such techniques, one may accept the risks involved if they can be brought down to manageable levels. Most of the nuclear techniques in use in industries in Malaysia require only minimal safety precautions as they make use of only small amounts of radioactive material. However, some large sources are also being used and safety precautions have to be strictly enforced. The management plays a critical role in these industries. The requirements for radiation safety include the monitoring of workers and work areas, the medical surveillance of workers and the provision of barriers and other safety precautions. The management should also look to the training of the workers and be prepared for any emergencies that may arise.

  10. Application of positron annihilation techniques for semiconductor studies

    International Nuclear Information System (INIS)

    Karwasz, G.P.; Zecca, A.; Brusa, R.S.; Pliszka, D.

    2004-01-01

    Positron annihilation techniques, being non-destructive, allowing depth profiling down to a few micrometers and detecting open-volume defects (vacancies, dislocations etc.) at single ppm concentrations constitute a valuable and complementary method, compared to other solid-state-physics studies. We give examples of investigation in the field of semiconductors with different techniques, both with and without use of positron low-energy beams. The Doppler broadening of the 511 keV annihilation line method and the slow positron beam were used to study helium-implanted silicon and the surface reduction processes in semiconducting glasses. The positron lifetime technique and coincidence spectra of the Doppler broadening were used for systematic studies of metals and semiconductors. Doppler-coincidence method was then used to identify the kinetics of oxygen precipitates in Czochralski-grown silicon

  11. Application of infrared technique in research of mechanical properties

    International Nuclear Information System (INIS)

    Huang, Y.; Shih, C.H.

    1985-08-01

    The infrared technique as a new method is more useful for research of materials science. This paper simply describes the techniques of infrared temperature measurement and thermography and provides the experimental data of some metals and alloys during the deformation and the fatigue process by use of the infrared sensing method. It is shown that the conventional tensile data can be correlated with infrared radiational energy change during the tensile pulling. The temperature field of metal during elastic-plastic deformation can be calculated by finite element analysis, and the thermoelastic effect of metal can be shown by thermography. The infrared technique can be used to predict the fatigue damage, monitor their propagations and give the alarm at fracture. Finally, it must be pointed out that the irreversibility of infrared emission of metal can be used as a basis of nondestructive testing. (author)

  12. Application of the Lorentz-transform technique to meson photoproduction

    International Nuclear Information System (INIS)

    Reiss, C.; Leidemann, W.; Orlandini, G.; Tomusiak, E.L.

    2003-01-01

    We show that the Lorentz integral transform (LIT) technique which has been successfully applied to photoreactions in light nuclei can also be applied to photoreactions involving particle production. A simple model where results are easily calculable in the traditional fashion is used to test the technique. Specifically, we compute inclusive π + photoproduction from deuterium for photon energies less than 200 MeV using a Yamaguchi model for the NN interaction. It is demonstrated that, although the response functions for inclusive meson production do not have favourable asymptotic behavior, one can nonetheless extract them by inversion of the transform. The implication is that one can treat realistic problems of photo-meson production, including all final-state interactions, by means of the LIT technique. (orig.)

  13. Model order reduction techniques with applications in finite element analysis

    CERN Document Server

    Qu, Zu-Qing

    2004-01-01

    Despite the continued rapid advance in computing speed and memory the increase in the complexity of models used by engineers persists in outpacing them. Even where there is access to the latest hardware, simulations are often extremely computationally intensive and time-consuming when full-blown models are under consideration. The need to reduce the computational cost involved when dealing with high-order/many-degree-of-freedom models can be offset by adroit computation. In this light, model-reduction methods have become a major goal of simulation and modeling research. Model reduction can also ameliorate problems in the correlation of widely used finite-element analyses and test analysis models produced by excessive system complexity. Model Order Reduction Techniques explains and compares such methods focusing mainly on recent work in dynamic condensation techniques: - Compares the effectiveness of static, exact, dynamic, SEREP and iterative-dynamic condensation techniques in producing valid reduced-order mo...

  14. Signal Morphing techniques and possible application to Higgs properties measurements

    CERN Document Server

    Ecker, Katharina Maria; The ATLAS collaboration

    2016-01-01

    One way of describing deviations from the Standard Model is via Effective Field Theories or pseudo-observables, where higher order operators modify the couplings and the kinematics of the interaction of the Standard Model particles. Generating Monte Carlo events for every testable set of parameters for such a theory would require computing resources beyond the ones currently available in ATLAS. Up to now, Matrix-Element based reweighting techniques have been often used to model Beyond Standard Model process starting from Standard Model simulated events. In this talk, we review the advantages and the limitations of morphing techniques to construct continuous probability model for signal parameters, interpolating between a finite number of distributions obtained from the simulation chain. The technique will be exemplified by searching for deviations from the Standard Model predictions in Higgs properties measurements.

  15. Discussion meet on electroanalytical techniques and their applications

    International Nuclear Information System (INIS)

    Aggarwal, S.K.; Gopinath, N.; Govindan, R.

    2008-02-01

    Electrochemistry is truly an interdisciplinary science and plays an important role in different branches of science and technology. The present Discussion Meet on ElectroAnalytical Techniques (DM- ELANTE-2008) is focused on the update of various electroanalytical techniques which have brought out a substantial change in electroanalytical chemistry. The aim of this Discussion Meet is to provide a forum to all the electroanalytical scientists to discuss their recent findings and information, learn from the mutual experiences and interests, and to promote cooperation both nationally and internationally. It is proposed to have tutorial lectures as well as invited talks during the Discussion Meet on various electroanalytical techniques including Electrochemical Impedance Spectroscopy (EIS), Spectro-electrochemistry, Scanning Electrochemical Microscopy (SECM), Electrochemical Quartz Crystal Microbalance (EQCM), Surface Plasmon Resonance (SPR) etc. Papers relevant to INIS are indexed separately

  16. Gamma radiography and its technological application; Gammagraphie et techniques annexes

    Energy Technology Data Exchange (ETDEWEB)

    Courtois, G [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1962-07-01

    After the presentation of gamma radiography and X-ray radiography, the author compare both techniques showing, in particular, the greater utility of gamma radiography in industrial diagnostic and more particularly on works site diagnostic. Problem of using radiography and safety consideration will be studied. Figures shows two radiography equipment which have been designed for gamma radiography respecting the safety regulations required by the Radioisotope Inter-ministerial Commission. In the second part, different techniques and uses of gamma radiography are briefly described : xerography, neutron radiography, fluoroscopy and imaging amplifier, tomography, betatrons and linear accelerators. Cost analysis will discussed in conclusion. (M.P.)

  17. Practical applications of activation analysis and other nuclear techniques

    International Nuclear Information System (INIS)

    Lyon, W.S.

    1982-01-01

    Neeutron activation analysis (NAA) is a versatile, sensitive multielement, usually nondestructive analytical technique used to determine elemental concentrations in a variety of materials. Samples are irradiated with neutrons in a nuclear reactor, removed, and for the nondestructive technique, the induced radioactivity measured. This measurement of γ rays emitted from specific radionuclides makes possible the quantitative determination of elements present. The method is described, advantages and disadvantages listed and a number of examples of its use given. Two other nuclear methods, particle induced x-ray emission and synchrotron produced x-ray fluorescence are also briefly discussed

  18. Techniques for Performance Improvement of Integer Multiplication in Cryptographic Applications

    Directory of Open Access Journals (Sweden)

    Robert Brumnik

    2014-01-01

    Full Text Available The problem of arithmetic operations performance in number fields is actively researched by many scientists, as evidenced by significant publications in this field. In this work, we offer some techniques to increase performance of software implementation of finite field multiplication algorithm, for both 32-bit and 64-bit platforms. The developed technique, called “delayed carry mechanism,” allows to preventing necessity to consider a significant bit carry at each iteration of the sum accumulation loop. This mechanism enables reducing the total number of additions and applies the modern parallelization technologies effectively.

  19. Application of nuclear techniques on environmental pollution problems

    International Nuclear Information System (INIS)

    Sumatra, Made

    1998-01-01

    Radioanalysis and tracer techniques that can be used on environmental pollution problems. Neutron activation analysis (NAA) and X-ray fluorescence (XRF) spectrometry are the two methods that are used frequently on such problems. These methods are used for metal analysis. Tracer technique with radioactive labeled compounds are used to study the fate of the pollution substances in environmental systems. It is very important to validate every new developed analysis method, due to the environmental pollution problem closely related to the low enforcement. (author)

  20. Application of microlearning technique and Twitter for educational purposes

    Science.gov (United States)

    Aitchanov, B. H.; Satabaldiyev, A. B.; Latuta, K. N.

    2013-04-01

    The current paper reviews the usage of social resource such as Twitter in microlearning technique for educational purposes. The problem is that most of instructors are unaware that with the help of social networks the students' productivity can increase. The research is applied on CS205 Advanced Programming in C++ course at Suleyman Demirel University (Kazakhstan). The collected results show that in a modern world of emerging mobile technologies, we are as educators should improve the way of teaching by adding electronically supported learning methods. In this study, the significance of microlearning technique is proposed.