Pencilbeam irradiation technique for whole brain radiotherapy: technical and biological challenges in a small animal model.

Science.gov (United States)

Schültke, Elisabeth; Trippel, Michael; Bräuer-Krisch, Elke; Renier, Michel; Bartzsch, Stefan; Requardt, Herwig; Döbrössy, Máté D; Nikkhah, Guido

2013-01-01

We have conducted the first in-vivo experiments in pencilbeam irradiation, a new synchrotron radiation technique based on the principle of microbeam irradiation, a concept of spatially fractionated high-dose irradiation. In an animal model of adult C57 BL/6J mice we have determined technical and physiological limitations with the present technical setup of the technique. Fifty-eight animals were distributed in eleven experimental groups, ten groups receiving whole brain radiotherapy with arrays of 50 µm wide beams. We have tested peak doses ranging between 172 Gy and 2,298 Gy at 3 mm depth. Animals in five groups received whole brain radiotherapy with a center-to-center (ctc) distance of 200 µm and a peak-to-valley ratio (PVDR) of ∼ 100, in the other five groups the ctc was 400 µm (PVDR ∼ 400). Motor and memory abilities were assessed during a six months observation period following irradiation. The lower dose limit, determined by the technical equipment, was at 172 Gy. The LD50 was about 1,164 Gy for a ctc of 200 µm and higher than 2,298 Gy for a ctc of 400 µm. Age-dependent loss in motor and memory performance was seen in all groups. Better overall performance (close to that of healthy controls) was seen in the groups irradiated with a ctc of 400 µm.

Systems study 'Alternative Entsorgung'. Final report. Technical annex 10

International Nuclear Information System (INIS)

Hartje, B.; Kronschnabel, H.; Mueller, W.F.W.

1984-01-01

There is an investigation whether accessibility can be produced to fuel elements stored in a salt mine. All solutions of the problem were followed up until the technically best one was found. Two conditions must be fulfilled for access to the final storage barrel: - There must be a climate which is suitable for people. The Mining Order is the basis for this. - The pit building must be fixed, in the convergence in the salt mine should not lead to it becoming impossible to reach part of the mine. Due to heat-producing waste, rock temperatures are caused in the salt mine, in which mining is no longer possible. Building on the idea of cooling the whole final storage area using concentric sections, the amount of heat to be removal was first estimated. Cooling of the whole final storage area proved to be technically unjustifiable and uninteresting at present. (orig./HP) [de

10 CFR 52.157 - Contents of applications; technical information in final safety analysis report.

Science.gov (United States)

2010-01-01

...; technical information in final safety analysis report. The application must contain a final safety analysis... 10 Energy 2 2010-01-01 2010-01-01 false Contents of applications; technical information in final safety analysis report. 52.157 Section 52.157 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) LICENSES...

10 CFR 52.79 - Contents of applications; technical information in final safety analysis report.

Science.gov (United States)

2010-01-01

...; technical information in final safety analysis report. (a) The application must contain a final safety... 10 Energy 2 2010-01-01 2010-01-01 false Contents of applications; technical information in final safety analysis report. 52.79 Section 52.79 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) LICENSES...

48 CFR 1852.235-73 - Final Scientific and Technical Reports.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 6 2010-10-01 2010-10-01 true Final Scientific and Technical Reports. 1852.235-73 Section 1852.235-73 Federal Acquisition Regulations System NATIONAL..., including recommendations and conclusions based on the experience and results obtained. The final report...

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Aristos Aristidou Natureworks); Robert Kean (NatureWorks); Tom Schechinger (IronHorse Farms, Mat); Stuart Birrell (Iowa State); Jill Euken (Wallace Foundation & Iowa State)

2007-10-01

The two main objectives of this project were: 1) to develop and test technologies to harvest, transport, store, and separate corn stover to supply a clean raw material to the bioproducts industry, and 2) engineer fermentation systems to meet performance targets for lactic acid and ethanol manufacturers. Significant progress was made in testing methods to harvest corn stover in a “single pass” harvest mode (collect corn grain and stover at the same time). This is technically feasible on small scale, but additional equipment refinements will be needed to facilitate cost effective harvest on a larger scale. Transportation models were developed, which indicate that at a corn stover yield of 2.8 tons/acre and purchase price of $35/ton stover, it would be unprofitable to transport stover more than about 25 miles; thus suggesting the development of many regional collection centers. Therefore, collection centers should be located within about 30 miles of the farm, to keep transportation costs to an acceptable level. These collection centers could then potentially do some preprocessing (to fractionate or increase bulk density) and/or ship the biomass by rail or barge to the final customers. Wet storage of stover via ensilage was tested, but no clear economic advantages were evident. Wet storage eliminates fire risk, but increases the complexity of component separation and may result in a small loss of carbohydrate content (fermentation potential). A study of possible supplier-producer relationships, concluded that a “quasi-vertical” integration model would be best suited for new bioproducts industries based on stover. In this model, the relationship would involve a multiyear supply contract (processor with purchase guarantees, producer group with supply guarantees). Price will likely be fixed or calculated based on some formula (possibly a cost plus). Initial quality requirements will be specified (but subject to refinement).Producers would invest in harvest

Technical and economical feasibility study of a sewage sludge disinfection plants by irradiation process

International Nuclear Information System (INIS)

Rojas Bustos, Gustavo

1999-01-01

This report presents a technical and economical evaluation for a disinfection plant of sewage sludge based on irradiation. The process starts after sludge stabilization which is achieved by anaerobic digestion. It includes two stages, plus an optional: the first corresponds to dewatering of sewage sludge up to a solids content between 20 and 25 %, the second stage corresponds to disinfection by gamma or electron beam irradiation, and the third, which is optional, corresponds to the drying of sewage sludge up to a water content of 50%, which allows to diminish significantly the volumes of solids to be transported. If this stage is not accomplished the final product corresponds to a sewage sludge with 25 % of dry solids, which can also be disposed in agricultural land. Process was designed to treat 60 tons per day of sewage sludge (dry matter basis). The report presents the design of process equipment, principal and auxiliary, the investment and operational cost estimations as well as the total cost of treatment per ton of sewage sludge. A sensitivity analysis is also included to determine the influence of operational process parameters in operational and investment costs. The results showed that a sewage sludge plant including dewatering and disinfection process through gamma irradiation, achieves a capital investment of about US$ 12.000.000 with a treatment cost per ton of dry sludge of US$140. Including the optional air-drying stage, the total cost of treatment is about US$148 per ton of dry matter. In the case of electron beam irradiation the capital investment achieves a value of US$ 11 millions with a total treatment cost of US$ 136 per ton of dry matter. These values resulted quite similar to the cost of alternative treatment, i.e., disposal in a dedicated landfill. (L.V.)

Irradiation of strawberries. A compilation of technical data for its authorization and control

International Nuclear Information System (INIS)

1994-12-01

The document contains a compilation of all available scientific and technical data on the irradiation of strawberries. It is intended to assist governments in considering the authorization of this particular application of radiation processing of food and in ensuring its control in the facility and the control of irradiated food products moving in trade. The compilation was prepared in response to the requirement of the Codex General Standard for Irradiated Foods and associated Code that radiation treatment of food be justified on the basis of a technological need or of a need to improve the hygienic quality of food. It was prepared also in response to the recommendations of the FAO/IAEA/WHO/ITC-UNCTAD/GATT International conference on the Acceptance, Control of and Trade in Irradiated Food (Geneva, 1989) concerning the need for regulatory control of radiation processing of food. Refs, 1 tab

Physico-technical irradiation planning for the therapy of oesophagus carcinomas by means of computed whole-body tomography

International Nuclear Information System (INIS)

Ammon, J.; Greiner, K.; Kaesberg, P.

1980-01-01

It is particularly difficult to establish a physico-technical irradiation plan for the thoracic part of an oesophagus carcinoma. This is due to the considerable modifications of the thoracic cross-section within the longitudinal axis of the radiation field. Therefore, tomographic cross-sections were made of the upper, the middle and the lower plane of the radiation field. The percentage dose distributions could be determined with a process computer (system TPS, Philips) for different irradiation techniques and irradiation equipments. Examinations of 21 patients showed that the best dose distribution, i.e. a distribution which spares the lung and spinal marrow regions adjacent to the target volume, is obtained by an excentric moving field therapy. Furthermore, localisation and dimensions of inhomogeneities are indicated by computer tomography which makes possible to take into consideration these inhomogeneities when calculating the dose. It was found that the irradiation times can so be reduced by more than 20%. We are therefore of the opinion that it is necessary to establish individual cross-sections of the body by computed tomography when elaborating a physico-technical irradiation plan for the treatment of an oesophagus carcinoma. (orig.) [de

Medical waste irradiation study. Final report

International Nuclear Information System (INIS)

Adler, R.J.; Stein, J.; Nygard, J.

1998-01-01

The North Star Research Corporation Medical Waste project is described in this report, with details of design, construction, operation, and results to date. The project began with preliminary design of the accelerator. The initial design was for a single accelerator chamber with a vacuum tube cavity driver built into the chamber itself, rather than using a commercial tube separate from the RF accelerator. The authors believed that this would provide more adjustability and permit better coupling to be obtained. They did not have sufficient success with that approach, and finally completed the project using a DC accelerator with a unique new scanning system to irradiate the waste

Medical waste irradiation study. Final report

Energy Technology Data Exchange (ETDEWEB)

Adler, R.J.; Stein, J. [North Star Research Corp., Albuquerque, NM (United States); Nygard, J. [Advance Bio-Control (United States)

1998-07-25

The North Star Research Corporation Medical Waste project is described in this report, with details of design, construction, operation, and results to date. The project began with preliminary design of the accelerator. The initial design was for a single accelerator chamber with a vacuum tube cavity driver built into the chamber itself, rather than using a commercial tube separate from the RF accelerator. The authors believed that this would provide more adjustability and permit better coupling to be obtained. They did not have sufficient success with that approach, and finally completed the project using a DC accelerator with a unique new scanning system to irradiate the waste.

DOE final technical report 3/1997 to 2/2005

International Nuclear Information System (INIS)

Gross, Franz L.

2005-01-01

DOE final technical report 3/1997 to 2/2005 This grant supported basic theoretical research into the derivation (from relativistic field theories) of relativistic equations for few body systems, with practical applications to the properties of 2 and 3 nucleon systems and to the nature of few-quark systems

77 FR 47495 - Final Priority; Technical Assistance on State Data Collection, Analysis, and Reporting-National...

Science.gov (United States)

2012-08-08

... Priority; Technical Assistance on State Data Collection, Analysis, and Reporting--National IDEA Technical... 34 CFR Chapter III [CFDA Number 84.373Z] Final Priority; Technical Assistance on State Data Collection, Analysis, and Reporting--National IDEA Technical Assistance Center on Early Childhood...

Technical area status report for low-level mixed waste final waste forms

International Nuclear Information System (INIS)

Mayberry, J.L.; DeWitt, L.M.; Darnell, R.

1993-08-01

The Final Waste Forms (FWF) Technical Area Status Report (TASR) Working Group, the Vitrification Working Group (WG), and the Performance Standards Working Group were established as subgroups to the FWF Technical Support Group (TSG). The FWF TASR WG is comprised of technical representatives from most of the major DOE sites, the Nuclear Regulatory Commission (NRC), the EPA Office of Solid Waste, and the EPA's Risk Reduction Engineering Laboratory (RREL). The primary activity of the FWF TASR Working Group was to investigate and report on the current status of FWFs for LLNM in this TASR. The FWF TASR Working Group determined the current status of the development of various waste forms described above by reviewing selected articles and technical reports, summarizing data, and establishing an initial set of FWF characteristics to be used in evaluating candidate FWFS; these characteristics are summarized in Section 2. After an initial review of available information, the FWF TASR Working Group chose to study the following groups of final waste forms: hydraulic cement, sulfur polymer cement, glass, ceramic, and organic binders. The organic binders included polyethylene, bitumen, vinyl ester styrene, epoxy, and urea formaldehyde. Section 3 provides a description of each final waste form. Based on the literature review, the gaps and deficiencies in information were summarized, and conclusions and recommendations were established. The information and data presented in this TASR are intended to assist the FWF Production and Assessment TSG in evaluating the Technical Task Plans (TTPs) submitted to DOE EM-50, and thus provide DOE with the necessary information for their FWF decision-making process. This FWF TASR will also assist the DOE and the MWIP in establishing the most acceptable final waste forms for the various LLMW streams stored at DOE facilities

76 FR 18624 - Research, Technical Assistance and Training Programs: Notice of Final Circular

Science.gov (United States)

2011-04-04

... to FTA Circular 6100.1D, Research and Technical Assistance Training Program: Application Instructions... DEPARTMENT OF TRANSPORTATION Federal Transit Administration Research, Technical Assistance and Training Programs: Notice of Final Circular AGENCY: Federal Transit Administration (FTA), DOT. ACTION...

Food irradiation receives international acceptance

Energy Technology Data Exchange (ETDEWEB)

Beddoes, J M [Atomic Energy of Canada Ltd., Ottawa, Ontario. Commercial Products

1982-04-01

Irradiation has advantages as a method of preserving food, especially in the Third World. The author tabulates some examples of actual use of food irradiation with dates and tonnages, and tells the story of the gradual acceptance of food irradiation by the World Health Organization, other international bodies, and the U.S. Food and Drug Administration (USFDA). At present, the joint IAEA/FAO/WHO standard permits an energy level of up to 5 MeV for gamma rays, well above the 1.3 MeV energy level of /sup 60/Co. The USFDA permits irradiation of any food up to 10 krad, and minor constituents of a diet may be irradiated up to 5 Mrad. The final hurdle to be cleared, that of economic acceptance, depends on convincing the food processing industry that the process is technically and economically efficient.

AIMES Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Katz, Daniel S [Univ. of Illinois, Urbana-Champaign, IL (United States). National Center for Supercomputing Applications (NCSA); Jha, Shantenu [Rutgers Univ., New Brunswick, NJ (United States); Weissman, Jon [Univ. of Minnesota, Minneapolis, MN (United States); Turilli, Matteo [Rutgers Univ., New Brunswick, NJ (United States)

2017-01-31

This is the final technical report for the AIMES project. Many important advances in science and engineering are due to large-scale distributed computing. Notwithstanding this reliance, we are still learning how to design and deploy large-scale production Distributed Computing Infrastructures (DCI). This is evidenced by missing design principles for DCI, and an absence of generally acceptable and usable distributed computing abstractions. The AIMES project was conceived against this backdrop, following on the heels of a comprehensive survey of scientific distributed applications. AIMES laid the foundations to address the tripartite challenge of dynamic resource management, integrating information, and portable and interoperable distributed applications. Four abstractions were defined and implemented: skeleton, resource bundle, pilot, and execution strategy. The four abstractions were implemented into software modules and then aggregated into the AIMES middleware. This middleware successfully integrates information across the application layer (skeletons) and resource layer (Bundles), derives a suitable execution strategy for the given skeleton and enacts its execution by means of pilots on one or more resources, depending on the application requirements, and resource availabilities and capabilities.

NCSU reactor sharing program. Final technical report

International Nuclear Information System (INIS)

Perez, P.B.

1997-01-01

The Nuclear Reactor Program at North Carolina State University provides the PULSTAR Research Reactor and associated facilities to eligible institutions with support, in part, from the Department of Energy Reactor Sharing Program. Participation in the NCSU Reactor Sharing Program continues to increase steadily with visitors ranging from advance high school physics and chemistry students to Ph.D. level research from neighboring universities. This report is the Final Technical Report for the DOE award reference number DE-FG05-95NE38136 which covers the period September 30, 1995 through September 30, 1996

Response to growth hormone treatment and final height after cranial or craniospinal irradiation

International Nuclear Information System (INIS)

Sulmont, V.; Brauner, R.; Fontoura, M.; Rappaport, R.

1990-01-01

Growth hormone (GH) deficiency (GHD) induced by cranial irradiation has become a frequent indication of hGH substitutive therapy. This study analyses the growth response to hGH therapy and the factors involved in the decrease in growth velocity observed after cranial irradiation. One hundred children given cranial radiation for pathology distant from the hypothalamo-pituitary area were studied. Fifty-six of them received hGH therapy for GHD resulting in decreased growth velocity. The initial annual height gain in the cranial-irradiated group was comparable to that of patients treated for idiopathic GHD; additional spinal irradiation significantly reduced the growth response. Twenty-eight hGH-treated patients reached final heights which were compared to those of 2 untreated irradiated groups, one with GHD (n=27) and the other with normal GH secretion (n=17). The height SD score changes observed in hGH therapy were +0.3 in the cranial (n=10) and -1.2 SD in the craniospinal (n=18) groups. GH deficiency had contributed to a mean height loss of 1 SD and spinal irradiation to a loss of 1.4SD. The small effect of hGH therapy on final height is probably linked to the small bone age retardation at onset of hGH therapy and to the fact that irradiated children entered puberty at a younger age in terms of chronological age and bone age than the idiopathic GHD patients. These data suggest that the results of gGH therapy in irradiated children might be improved with higher and more fractionated hGH doses and, in some patients, by delaying puberty using luteinizing hormone releasing hormone analogs

Response to growth hormone treatment and final height after cranial or craniospinal irradiation

Energy Technology Data Exchange (ETDEWEB)

Sulmont, V.; Brauner, R.; Fontoura, M.; Rappaport, R. (Hospital des Enfants Malades, Paris (France). Pediatric Endocrinology Unit and INSERM U30)

1990-01-01

Growth hormone (GH) deficiency (GHD) induced by cranial irradiation has become a frequent indication of hGH substitutive therapy. This study analyses the growth response to hGH therapy and the factors involved in the decrease in growth velocity observed after cranial irradiation. One hundred children given cranial radiation for pathology distant from the hypothalamo-pituitary area were studied. Fifty-six of them received hGH therapy for GHD resulting in decreased growth velocity. The initial annual height gain in the cranial-irradiated group was comparable to that of patients treated for idiopathic GHD; additional spinal irradiation significantly reduced the growth response. Twenty-eight hGH-treated patients reached final heights which were compared to those of 2 untreated irradiated groups, one with GHD (n=27) and the other with normal GH secretion (n=17). The height SD score changes observed in hGH therapy were +0.3 in the cranial (n=10) and -1.2 SD in the craniospinal (n=18) groups. GH deficiency had contributed to a mean height loss of 1 SD and spinal irradiation to a loss of 1.4SD. The small effect of hGH therapy on final height is probably linked to the small bone age retardation at onset of hGH therapy and to the fact that irradiated children entered puberty at a younger age in terms of chronological age and bone age than the idiopathic GHD patients. These data suggest that the results of gGH therapy in irradiated children might be improved with higher and more fractionated hGH doses and, in some patients, by delaying puberty using luteinizing hormone releasing hormone analogs.

Food irradiation receives international acceptance

International Nuclear Information System (INIS)

Beddoes, J.M.

1982-01-01

Irradition has advantages as a method of preserving food, especially in the Third World. The author tabulates some examples of actual use of food irradiation with dates and tonnages, and tells the story of the gradual acceptance of food irradiation by the World Health Organization, other international bodies, and the U.S. Food and Drug Administration (USFDA). At present, the joint IAEA/FAO/WHO standard permits an energy level of up to 5 MeV for gamma rays, well above the 1.3 MeV energy level of 60 Co. The USFDA permits irradiation of any food up to 10 krad, and minor constituents of a diet may be irradiated up to 5 Mrad. The final hurdle to be cleared, that of economic acceptance, depends on convincing the food processing industry that the process is technically and economically efficient

Irradiation of red meat. A compilation of technical data for its authorization and control

International Nuclear Information System (INIS)

1996-08-01

The aim of this monograph is to provide the rationale and justification for treating red meats with ionizing radiation for improving microbiological safety, parasite control and extending non-frozen shelf-life. It is intended to complement a previous publication ''Irradiation of Poultry Meat and its Products - A compilation of Technical Data for its Authorization and Control''. 146 refs

Irradiation of red meat. A compilation of technical data for its authorization and control

Energy Technology Data Exchange (ETDEWEB)

International consultative group on food irradiation

1996-08-01

The aim of this monograph is to provide the rationale and justification for treating red meats with ionizing radiation for improving microbiological safety, parasite control and extending non-frozen shelf-life. It is intended to complement a previous publication ``Irradiation of Poultry Meat and its Products - A compilation of Technical Data for its Authorization and Control``. 146 refs.

High energy physics research. Final technical report, 1957--1994

International Nuclear Information System (INIS)

Williams, H.H.

1995-01-01

This is the final technical report to the Department of Energy on High Energy Physics at the University of Pennsylvania. It discusses research conducted in the following areas: neutrino astrophysics and cosmology; string theory; electroweak and collider physics; supergravity; cp violation and baryogenesis; particle cosmology; collider detector at Fermilab; the sudbury neutrino observatory; B-physics; particle physics in nuclei; and advanced electronics and detector development

High energy physics research. Final technical report, 1957--1994

Energy Technology Data Exchange (ETDEWEB)

Williams, H.H.

1995-10-01

This is the final technical report to the Department of Energy on High Energy Physics at the University of Pennsylvania. It discusses research conducted in the following areas: neutrino astrophysics and cosmology; string theory; electroweak and collider physics; supergravity; cp violation and baryogenesis; particle cosmology; collider detector at Fermilab; the sudbury neutrino observatory; B-physics; particle physics in nuclei; and advanced electronics and detector development.

Technical approach to finalizing sensible soil cleanup levels at the Fernald Environmental Management Project

International Nuclear Information System (INIS)

Carr, D.; Hertel, B.; Jewett, M.; Janke, R.; Conner, B.

1996-01-01

The remedial strategy for addressing contaminated environmental media was recently finalized for the US Department of Energy's (DOE) Fernald Environmental Management Project (FEMP) following almost 10 years of detailed technical analysis. The FEMP represents one of the first major nuclear facilities to successfully complete the Remedial Investigation/Feasibility Study (RI/FS) phase of the environmental restoration process. A critical element of this success was the establishment of sensible cleanup levels for contaminated soil and groundwater both on and off the FEMP property. These cleanup levels were derived based upon a strict application of Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) regulations and guidance, coupled with positive input from the regulatory agencies and the local community regarding projected future land uses for the site. The approach for establishing the cleanup levels was based upon a Feasibility Study (FS) strategy that examined a bounding range of viable future land uses for the site. Within each land use, the cost and technical implications of a range of health-protective cleanup levels for the environmental media were analyzed. Technical considerations in driving these cleanup levels included: direct exposure routes to viable human receptors; cross- media impacts to air, surface water, and groundwater; technical practicality of attaining the levels; volume of affected media; impact to sensitive environmental receptors or ecosystems; and cost. This paper will discuss the technical approach used to support the finalization of the cleanup levels for the site. The final cleanup levels provide the last remaining significant piece to the puzzle of establishing a final site-wide remedial strategy for the FEMP, and positions the facility for the expedient completion of site-wide remedial activities

Audit of Wolf Creek Generating Station, Unit 1 technical specifications. Final technical evaluation report

International Nuclear Information System (INIS)

Stromberg, H.M.

1985-07-01

This document was prepared for the Nuclear Regulatory Commission (NRC) to assist them in determining whether the Wolf Creek Generating Station Unit 1 Technical Specifications (T/S), which govern plant systems configurations and operations, are in conformance with the assumptions of the Final Safety Analysis Report (FSAR) as amended, the requirements of the Safety Evaluation Report (SER) as supplemented, and the Comments and Responses to the Wolf Creek Technical Specification Draft Inspection Report. A comparative audit of the FSAR as amended, the SER as supplemented, and the Draft Inspection Report was performed with the Wolf Creek T/S. Several discrepancies were identified and subsequently resolved through discussions with the cognizant NRC reviewer, NRC staff reviewers and/or utility representatives. The Wolf Creek Generating Station Unit 1 T/S, to the extent reviewed, are in conformance with the FSAR, SER, and Draft Inspection Report

78 FR 12955 - Final Requirements, Definitions, and Selection Criteria-Native American Career and Technical...

Science.gov (United States)

2013-02-26

... career and technical education programs (20 U.S.C. 2326(e)). This notice does not preclude us from... DEPARTMENT OF EDUCATION 34 CFR Chapter IV [Docket ID ED-2012-OVAE-0053] Final Requirements, Definitions, and Selection Criteria--Native American Career and Technical Education Program (NACTEP) [Catalog...

Technical planning activity: Final report

Energy Technology Data Exchange (ETDEWEB)

1987-01-01

In April 1985, the US Department of Energy's (DOE's) Office of Fusion Energy commissioned the Technical Planning Activity (TPA). The purpose of this activity was to develop a technical planning methodology and prepare technical plans in support of the strategic and policy framework of the Magnetic Fusion Program Plan issued by DOE in February 1985. Although this report represents the views of only the US magnetic fusion community, it is international in scope in the sense that the technical plans contained herein describe the full scope of the tasks that are prerequisites for the commercialization of fusion energy. The TPA has developed a well-structured methodology that includes detailed definitions of technical issues, definitions of program areas and elements, statements of research and development objectives, identification of key decision points and milestones, and descriptions of facility requirements.

Technical planning activity: Final report

International Nuclear Information System (INIS)

1987-01-01

In April 1985, the US Department of Energy's (DOE's) Office of Fusion Energy commissioned the Technical Planning Activity (TPA). The purpose of this activity was to develop a technical planning methodology and prepare technical plans in support of the strategic and policy framework of the Magnetic Fusion Program Plan issued by DOE in February 1985. Although this report represents the views of only the US magnetic fusion community, it is international in scope in the sense that the technical plans contained herein describe the full scope of the tasks that are prerequisites for the commercialization of fusion energy. The TPA has developed a well-structured methodology that includes detailed definitions of technical issues, definitions of program areas and elements, statements of research and development objectives, identification of key decision points and milestones, and descriptions of facility requirements

Evaluation of irradiated sewage sludges

International Nuclear Information System (INIS)

Colin C, A.

1994-01-01

The residual muds are produced by a separation process in the black waters treatment constituted by a solid phase whose origin is the accumulation of pollutant matter that has been extended to the water for anthropogenic and/or natural activities. The present work has the purpose to carry out a technical evaluation for the irradiation process of residual muds for their possible application like alternative of treatment and final disposal. The results obtained for the Evaluation of the irradiation of residual muds are bounded with the federative entities in the study, on the number of treatment plants of residual waters by diverse methods, discharge types, system location, residual muds production and muds treatment, uses and final disposal. The results show in the several entities,a great variety and versatility of industrial branches with diverse systems for treatment of waters and scarceness in the systems for residual muds treatment. (Author)

SUPPLEMENTARY COMPARISON: Final report on APMP.PR-S1.1: Bilateral comparison of irradiance responsivity of UVA detectors

Science.gov (United States)

Huang, Xuebo

2009-01-01

In order to assess the performance of the standards and techniques used for calibration and measurement of UVA irradiance responsivity of photodetectors in NMISA, South Africa, a new comparison was decided as a follow-up to comparison APMP.PR-S1. It is registered in the Key Comparison Data Base (KCDB) of BIPM as a bilateral supplementary comparison, with the identifier APMP.PR-S1.1. The comparison was carried out following the same technical protocol as that of supplementary comparison APMP PR-S1. The principle, organization and method of the comparison, as well as the preliminary measurements at the pilot laboratory NMC-A*STAR Singapore, were described in the Final Report of the APMP.PR-S1 comparison. The results of this bilateral comparison show that the NMISA's results lie within ±2% against the comparison reference values of APMP.PR-S1, which is a great improvement. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the APMP, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

Technical area status report for low-level mixed waste final waste forms. Volume 1

Energy Technology Data Exchange (ETDEWEB)

Mayberry, J.L.; DeWitt, L.M. [Science Applications International Corp., Idaho Falls, ID (United States); Darnell, R. [EG and G Idaho, Inc., Idaho Falls, ID (United States)] [and others

1993-08-01

The Final Waste Forms (FWF) Technical Area Status Report (TASR) Working Group, the Vitrification Working Group (WG), and the Performance Standards Working Group were established as subgroups to the FWF Technical Support Group (TSG). The FWF TASR WG is comprised of technical representatives from most of the major DOE sites, the Nuclear Regulatory Commission (NRC), the EPA Office of Solid Waste, and the EPA`s Risk Reduction Engineering Laboratory (RREL). The primary activity of the FWF TASR Working Group was to investigate and report on the current status of FWFs for LLNM in this TASR. The FWF TASR Working Group determined the current status of the development of various waste forms described above by reviewing selected articles and technical reports, summarizing data, and establishing an initial set of FWF characteristics to be used in evaluating candidate FWFS; these characteristics are summarized in Section 2. After an initial review of available information, the FWF TASR Working Group chose to study the following groups of final waste forms: hydraulic cement, sulfur polymer cement, glass, ceramic, and organic binders. The organic binders included polyethylene, bitumen, vinyl ester styrene, epoxy, and urea formaldehyde. Section 3 provides a description of each final waste form. Based on the literature review, the gaps and deficiencies in information were summarized, and conclusions and recommendations were established. The information and data presented in this TASR are intended to assist the FWF Production and Assessment TSG in evaluating the Technical Task Plans (TTPs) submitted to DOE EM-50, and thus provide DOE with the necessary information for their FWF decision-making process. This FWF TASR will also assist the DOE and the MWIP in establishing the most acceptable final waste forms for the various LLMW streams stored at DOE facilities.

77 FR 30512 - Native American Career and Technical Education Program; Final Waivers and Extension of Project...

Science.gov (United States)

2012-05-23

... DEPARTMENT OF EDUCATION Native American Career and Technical Education Program; Final Waivers and... American Career and Technical Education Program Catalog of Federal Domestic Assistance (CFDA) Number: 84... and Technical Education Program (NACTEP), the Secretary waives 34 CFR 75.250 and 75.261(c)(2) in order...

Irradiation of bulbs and tuber crops. A compilation of technical data for its authorization and control

International Nuclear Information System (INIS)

1997-04-01

This publication contains a compilation of available scientific and technical data on the irradiation of bulbs and tuber crops. It is intended to assist governments in considering the authorization of this particular application of radiation processing of food and in ensuring its control in the facility and the control of irradiated food products moving in trade. The compilation was prepared in response to the requirement of the Codex General Standard for Irradiated Foods and associated Code that radiation treatment of food be justified on the basis of a technological need or of a need to improve the hygienic quality of the food. It was also in response to the recommendations of the FAO/IAEA/WHO/ITC-UNCTAD/GATT International Conference on the Acceptance, Control of and Trade in Irradiated Food (Geneva, 1989) concerning the need for regulatory control of radiation processing of food. 448 refs, 6 tabs

Technical review on irradiation tests and post-irradiation examinations in JMTR

International Nuclear Information System (INIS)

2017-07-01

The Japan Materials Testing Reactor (JMTR) has been contributing to various R and D activities in the nuclear research such as the fundamental research of nuclear materials/ fuels, safety research and development of power reactors, radio isotope (RI) production since its beginning of the operation in 1968. Irradiation technologies and post irradiation examination (PIE) technologies are the important factors for irradiation test research. Moreover, these technologies induce the breakthrough in area of nuclear research. JMTR has been providing unique capabilities for the irradiation test research for about 40 years since 1968. In future, any needs for irradiation test research used irradiation test reactors will continue, such as R and D of generation 4 power reactors, fundamental research of materials/fuels, RI production. Now, decontamination and new research reactor construction are common issue in the world according to aging. This situation is the same in Japan. This report outlines irradiation and PIE technologies developed at JMTR in 40 years to contribute to the technology transfer and human resource development. We hope that this report will be used for the new research rector design as well as the irradiation test research and also used for the human resource development of nuclear engineers in future. (author)

Design, Manufacturing and Irradiation Behaviour of Fast Reactor Fuel. Proceedings of a Technical Meeting

International Nuclear Information System (INIS)

2013-04-01

Fast reactors are vital for ensuring the sustainability of nuclear energy in the long term. They offer vastly more efficient use of uranium resources and the ability to burn actinides, which are otherwise the long-lived component of high level nuclear waste. These reactors require development, qualification, testing and deployment of improved and innovative nuclear fuel and structural materials having very high radiation resistance, corrosion/erosion and other key operational properties. Several IAEA Member States have made efforts to advance the design and manufacture of technologies of fast reactor fuels, as well as to investigate their irradiation behaviour. Due to the acute shortage of fast neutron testing and post-irradiation examination facilities and the insufficient understanding of high dose radiation effects, there is a need for international exchange of knowledge and experience, generation of currently missing basic data, identification of relevant mechanisms of materials degradation and development of appropriate models. Considering the important role of nuclear fuels in fast reactor operation, the IAEA Technical Working Group on Fuel Performance and Technology (TWGFPT) proposed a Technical Meeting (TM) on 'Design, Manufacturing and Irradiation Behaviour of Fast Reactors Fuels', which was hosted by the Institute of Physics and Power Engineering (IPPE) in Obninsk, Russian Federation, from 30 May to 3 June 2011. The TM included a technical visit to the fuel production plant MSZ in Elektrostal. The purpose of the meeting was to provide a forum to share knowledge, practical experience and information on the improvement and innovation of fuels for fast reactors through scientific presentations and brainstorming discussions. The meeting brought together 34 specialists from national nuclear agencies, R and D and design institutes, fuel vendors and utilities from 10 countries. The presentations were structured into four sections: R and D Programmes on FR Fuel

"Type Ia Supernovae: Tools for Studying Dark Energy" Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Woosley, Stan [Lick Observatory, San Jose, CA (United States); Kasen, Dan [Univ. of California, Berkeley, CA (United States)

2017-05-10

Final technical report for project "Type Ia Supernovae: Tools for the Study of Dark Energy" awarded jointly to scientists at the University of California, Santa Cruz and Berkeley, for computer modeling, theory and data analysis relevant to the use of Type Ia supernovae as standard candles for cosmology.

Key technical issues associated with a method of pulse compression. Final technical report

International Nuclear Information System (INIS)

Hunter, R.O. Jr.

1980-06-01

Key technical issues for angular multiplexing as a method of pulse compression in a 100 KJ KrF laser have been studied. Environmental issues studied include seismic vibrations man-made vibrations, air propagation, turbulence, and thermal gradient-induced density fluctuations. These studies have been incorporated in the design of mirror mounts and an alignment system, both of which are reported. A design study and performance analysis of the final amplifier have been undertaken. The pulse compression optical train has been designed and assessed as to its performance. Individual components are described and analytical relationships between the optical component size, surface quality, damage threshold and final focus properties are derived. The optical train primary aberrations are obtained and a method for aberration minimization is presented. Cost algorithms for the mirrors, mounts, and electrical hardware are integrated into a cost model to determine system costs as a function of pulse length, aperture size, and spot size

The Michigan high-level radioactive waste program: Final technical progress report

International Nuclear Information System (INIS)

1987-01-01

This report comprises the state of Michigan's final technical report on the location of a proposed high-level radioactive waste disposal site. Included are a list of Michigan's efforts to review the DOE proposal and a detailed report on the application of geographic information systems analysis techniques to the review process

Irradiated Fuel Management Advisory Programme (IFMAP). An interregional technical co-operation project

International Nuclear Information System (INIS)

1993-04-01

Delays in the implementation of the fuel reprocessing option in some countries, the complete abandonment of this option in other countries, and delays in the availability of final spent fuel disposal in almost all countries, has led to increasingly long periods of 'interim' spent fuel storage. The problem of the management of irradiated fuels has therefore increased in importance for many Member States. For power reactors or research reactors, irradiated fuel management includes all of the procedures involving irradiated fuel from the time that it is discharged from the reactor core until it is either reprocessed or placed in a permanent disposal site. Although the IAEA has had programmes in this area in the past and has ongoing activities at present, there is a clear need to provide support to individual Member States which require advice and/or assistance in the resolution of particular questions and concerns

Final Technical Report, Wind Generator Project (Ann Arbor)

Energy Technology Data Exchange (ETDEWEB)

Geisler, Nathan [City of Ann Arbor, MI (United States)

2017-03-20

A Final Technical Report (57 pages) describing educational exhibits and devices focused on wind energy, and related outreach activities and programs. Project partnership includes the City of Ann Arbor, MI and the Ann Arbor Hands-on Museum, along with additional sub-recipients, and U.S. Department of Energy/Office of Energy Efficiency and Renewable Energy (EERE). Report relays key milestones and sub-tasks as well as numerous graphics and images of five (5) transportable wind energy demonstration devices and five (5) wind energy exhibits designed and constructed between 2014 and 2016 for transport and use by the Ann Arbor Hands-on Museum.

Iowa Hill Pumped Storage Project Investigations - Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Hanson, David [Sacramento Municipal Unitlity District, Sacramento, CA (United States)

2016-07-01

This Final Technical Report is a summary of the activities and outcome of the Department of Energy (DOE) Assistance Agreement DE-EE0005414 with the Sacramento Municipal Utility District (SMUD). The Assistance Agreement was created in 2012 to support investigations into the Iowa Hill Pumped-storage Project (Project), a new development that would add an additional 400 MW of capacity to SMUD’s existing 688MW Upper American River Hydroelectric Project (UARP) in the Sierra Nevada mountains east of Sacramento, California.

Admiralty Inlet Pilot Tidal Project Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Collar, Craig [Public Utility District No. 1 of Snohomish County, Everett, WA (United States)

2015-09-14

This document represents the final report for the Admiralty Inlet Pilot Tidal Project, located in Puget Sound, Washington, United States. The Project purpose was to license, permit, and install a grid-connected deep-water tidal turbine array (two turbines) to be used as a platform to gather operational and environmental data on tidal energy generation. The data could then be used to better inform the viability of commercial tidal energy generation from technical, economic, social, and environmental standpoints. This data would serve as a critical step towards the responsible advancement of commercial scale tidal energy in the United States and around the world. In late 2014, Project activities were discontinued due to escalating costs, and the DOE award was terminated in early 2015. Permitting, licensing, and engineering design activities were completed under this award. Final design, deployment, operation, and monitoring were not completed. This report discusses the results and accomplishments achieved under the subject award.

AGR-1 Irradiation Test Final As-Run Report, Rev. 3

Energy Technology Data Exchange (ETDEWEB)

Collin, Blaise P. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2015-01-01

This document presents the as-run analysis of the AGR-1 irradiation experiment. AGR-1 is the first of eight planned irradiations for the Advanced Gas Reactor (AGR) Fuel Development and Qualification Program. Funding for this program is provided by the US Department of Energy (DOE) as part of the Next-Generation Nuclear Plant (NGNP) project. The objectives of the AGR-1 experiment are: 1. To gain experience with multi-capsule test train design, fabrication, and operation with the intent to reduce the probability of capsule or test train failure in subsequent irradiation tests. 2. To irradiate fuel produced in conjunction with the AGR fuel process development effort. 3. To provide data that will support the development of an understanding of the relationship between fuel fabrication processes, fuel product properties, and irradiation performance. In order to achieve the test objectives, the AGR-1 experiment was irradiated in the B-10 position of the Advanced Test Reactor (ATR) at the Idaho National Laboratory (INL) for a total duration of 620 effective full power days of irradiation. Irradiation began on December 24, 2006 and ended on November 6, 2009 spanning 13 ATR cycles and approximately three calendar years. The test contained six independently controlled and monitored capsules. Each capsule contained 12 compacts of a single type, or variant, of the AGR coated fuel. No fuel particles failed during the AGR-1 irradiation. Final burnup values on a per compact basis ranged from 11.5 to 19.6 %FIMA, while fast fluence values ranged from 2.21 to 4.39 x 10²⁵ n/m² (E >0.18 MeV). We’ll say something here about temperatures once thermal recalc is done. Thermocouples performed well, failing at a lower rate than expected. At the end of the irradiation, nine of the originally-planned 19 TCs were considered functional. Fission product release-to-birth (R/B) ratios were quite low. In most capsules, R/B values at the end of the irradiation were at or below

77 FR 30514 - Native Hawaiian Career and Technical Education Program; Final Waiver and Extension of Project Period

Science.gov (United States)

2012-05-23

... DEPARTMENT OF EDUCATION Native Hawaiian Career and Technical Education Program; Final Waiver and... Career and Technical Education Program Catalog of Federal Domestic Assistance (CFDA) Number: 84.259A... Technical Education Program (NHCTEP), the Secretary hereby waives 34 CFR 75.261(c)(2) in order to extend the...

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Schuur, Edward [Northern Arizona Univ., Flagstaff, AZ (United States); Luo, Yiqi [Univ. of Oklahoma, Norman, OK (United States)

2016-12-01

This final grant report is a continuation of the final grant report submitted for DE-SC0006982 as the Principle Investigator (Schuur) relocated from the University of Florida to Northern Arizona University. This report summarizes the original project goals, as well as includes new project activities that were completed in the final period of the project.

Characterization of the radon source in North-Central Florida. Final report part 1 -- Final project report; Final report part 2 -- Technical report

International Nuclear Information System (INIS)

1997-01-01

This report contains two separate parts: Characterization of the Radon Source in North-Central Florida (final report part 1 -- final project report); and Characterization of the Radon Source in North-Central Florida (technical report). The objectives were to characterize the radon 222 source in a region having a demonstrated elevated indoor radon potential and having geology, lithology, and climate that are different from those in other regions of the U.S. where radon is being studied. Radon availability and transport in this region were described. Approaches for predicting the radon potential of lands in this region were developed

Clean Energy Works Oregon Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Jacob, Andria [City of Portland; Cyr, Shirley [Clean Energy Works

2013-12-31

In April 2010, the City of Portland received a $20 million award from the U.S. Department of Energy, as part of the Energy Efficiency and Conservation Block Grant program. This award was appropriated under the American Recovery and Reinvestment Act (ARRA), passed by President Obama in 2009. DOE’s program became known as the Better Buildings Neighborhood Program (BBNP). The BBNP grant objectives directed the City of Portland Bureau of Planning and Sustainability (BPS) as the primary grantee to expand the BPS-led pilot program, Clean Energy Works Portland, into Clean Energy Works Oregon (CEWO), with the mission to deliver thousands of home energy retrofits, create jobs, save energy and reduce carbon dioxide emissions.The Final Technical Report explores the successes and lessons learned from the first 3 years of program implementation.

Energy Impact Illinois - Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Olson, Daniel [Senior Energy Efficiency Planner; Plagman, Emily [Senior Energy Planner; Silberhorn, Joey-Lin [Energy Efficiency Program Assistant

2014-02-18

Energy Impact Illinois (EI2) is an alliance of government organizations, nonprofits, and regional utility companies led by the Chicago Metropolitan Agency for Planning (CMAP) that is dedicated to helping communities in the Chicago metropolitan area become more energy efficient. Originally organized as the Chicago Region Retrofit Ramp-Up (CR3), EI2 became part of the nationwide Better Buildings Neighborhood Program (BBNP) in May 2010 after receiving a $25 million award from the U.S. Department of Energy (DOE) authorized through the American Recovery and Reinvestment Act of 2009 (ARRA). The program’s primary goal was to fund initiatives that mitigate barriers to energy efficiency retrofitting activities across residential, multifamily, and commercial building sectors in the seven-county CMAP region and to help to build a sustainable energy efficiency marketplace. The EI2 Final Technical Report provides a detailed review of the strategies, implementation methods, challenges, lessons learned, and final results of the EI2 program during the initial grant period from 2010-2013. During the program period, EI2 successfully increased direct retrofit activity in the region and was able to make a broader impact on the energy efficiency market in the Chicago region. As the period of performance for the initial grant comes to an end, EI2’s legacy raises the bar for the region in terms of helping homeowners and building owners to take action on the continually complex issue of energy efficiency.

The technical need for food irradiation as a basis for approval

International Nuclear Information System (INIS)

Boegl, K.W.; Dehne, L.I.; Helle, N.; Schreiber, G.A.; Schuettler, C.; Zagon, J.

1992-01-01

The contribution deals with the development of legal regulations concerning irradiated food and the discussions during the last 35 years about the technical need, the different points of view about health consequences, and the behaviour and expectations of consumers. The attitudes of the German Research Society, the Federal Health Office, of Federal Parliament and Federal Council, of the Federal Government and of the governments of the states, and of international organizations are discussed in the light of three factors: - is there any need for action, - political determination, and - change of implementation. Legal restrictions and consumer behaviour may influence developments in the field of alternative techniques. To what extent is, exemplified by spices and dried vegetables. (orig.) [de

Final Technical Report for DE-FG02-98ER45737

Energy Technology Data Exchange (ETDEWEB)

Ade, Harald W.

2018-04-24

Final Technical Report For DOE Grant No. DE-FG02-98ER45737 Development of a Scanning Transmission X-Ray Microscope Polymer Thin Films and Self Assembled Monolayers: Pattern Formation and Surface Interactions NEXAFS Microscopy and Resonant Scattering of Polymeric Materials Organic Heterojunction Devices: Structure, Composition, and Performance at <20 nm Resolution Fundamental Science of High Open Circuit Voltage Excitonic Solar Cells Control of Interface- and Mesoscopic Structure in High Performance Organic Solar Cells: Towards a Predictive Device Paradigm

Summary report of the final technical meeting on 'International Reactor Dosimetry File: IRDF-2002'

International Nuclear Information System (INIS)

Griffin, Patrick J.; Paviotti-Corcuera, R.

2003-10-01

Presentations, recommendations and conclusions of the Final Technical Meeting on 'International Reactor Dosimetry File: IRDF-2002' are summarized in this report. The main aims of this meeting were to discuss scientific and technical matters related to reactor dosimetry and to assign responsibilities for the preparation of the final version of the IRDF- 2002 library and the associated TECDOC. Tasks were assigned and deadlines were agreed. Participants emphasized that accurate and complete nuclear data for reactor dosimetry are essential to improve the assessment accuracies for reactor pressure vessel service lifetimes in nuclear power plants, as well as for other neutron metrology applications such as boron neutron capture therapy, therapeutic use of medical isotopes, nuclear physics measurements, and reactor safety applications. (author)

Radiation-disorder and aperiodicity in irradiated ceramics

International Nuclear Information System (INIS)

Hobbs, L.W.

1992-01-01

This final technical report documents the accomplishments of the program of research entitled ''Radiation Disorder and Aperiodicity in Irradiated Ceramics'' for the period June 22, 1989--June 21, 1992. This research forms the latest part on an on-going program, begun at MIT in 1983 under DOE support, which has had as its objectives investigation of the responses in radiation environments of ceramics heavily-irradiated with electrons, neutrons and ions, with potential applications to fusion energy technology and high-level nuclear waste storage. Materials investigated have included SiO 2 , MgAl 2 O 4 , Al 23 O 27 N 5 , SiC, BeO, LiAlO 2 , Li 2 ZrO 3 , CaTiO 3 KTaO 3 and Ca(Zr, Pu)Ti 2 O 7 . The program initially proposed for 1989 had as its major objectives two main thrusts: (1) research on defect aggregation in irradiated non-oxide ceramics, and (2) research on irradiation-induced amorphization of network silicas and phosphates

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Eggeman, Tim [ZeaChem Inc., Lakewood, CO (United States); O' Neill, Brian [ZeaChem Inc., Lakewood, CO (United States)

2016-08-17

ZeaChem Inc. and US DOE successfully demonstrated the ZeaChem process for producing sugars and ethanol from high-impact biomass feedstocks. The project was executed over a 5-year period under a $31.25 million cooperative agreement (80:20 Federal:ZeaChem cost share). The project was managed by dividing it into three budget periods. Activities during Budget Period 1 were limited to planning, permitting, and other pre-construction planning. Budget Period 2 activities included engineering, procurement, construction, commissioning, start-up and initial operations through the Independent Engineer Test Runs. The scope of construction was limited to the Chem Frac and Hydrogenolysis units, as the Core Facility was already in place. Construction was complete in December 2012, and the first cellulosic ethanol was produced in February 2013. Additional operational test runs were conducted during Budget Period 3 (completed June 2015) using hybrid poplar, corn stover, and wheat straw feedstocks, resulting in the production of cellulosic ethanol and various other biorefinery intermediates. The research adds to the understanding of the Chem Frac and Hydrogenolysis technologies in that the technical performance of each unit was measured, and the resulting data and operational experience can be used as the basis for engineering designs, thus mitigating risks for deployment in future commercial facilities. The Chem Frac unit was initially designed to be operated as two-stage dilute acid hydrolysis, with first stage conditions selected to remove the hemicellulose fraction of the feedstock, and the second stage conditions selected to remove the cellulose fraction. While the Chem Frac unit met or exceeded the design capacity of 10 ton(dry)/day, the technical effectiveness of the Chem Frac unit was below expectations in its initial two-stage dilute acid configuration. The sugars yields were low, the sugars were dilute, and the sugars had poor fermentability caused by excessive inhibitors

Food irradiation: Some regulatory and technical aspects

International Nuclear Information System (INIS)

1985-10-01

An Advisory Group by IAEA and FAO on Regulatory and Technological Requirements for Authorization of the Food Irradiation Process was held at IAEA Headquarters in Vienna from 5 to 9 November 1984. The task of the Advisory Group was to advise on the scientific and technological considerations affecting the implementation of the food irradiation process, with particular reference to the facilitation of international trade in irradiated foods and to develop guidance on how the various provisions of the Codex General Standard on Irradiated Foods could be incorporated into national legislation in order to facilitate international trade and avoid the occurence of trade barriers. Separate abstracts were prepared for the various presentations at this meeting

DE-FG02-04ER63746 FinalTechnicalReport

Energy Technology Data Exchange (ETDEWEB)

Lidstrom, M.E.

2009-09-05

This is the final technical report for a project involving the study of stress response systems in the radiation-resistant bacterium, Deinococcus radiodurans. Three stresses of importance for a mixed waste treatment strain were studied, heat shock, solvent shock, and phosphate starvation. In each case, specific genes involved in the ability to survive the stress were identified using a systems biology approach, and analysis of mutants was used to understand mechanisms. This study has led to increased understanding of the ways in which a potential treatment strain could be manipulated to survive multiple stresses for treatment of mixed wastes.

Mathematics Intensive Summer Session (MISS). Final technical report

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-11-01

This final technical report appears in two parts: the report for the 1995 summer MISS program and the report for the 1996 summer MISS program. Copies of the US Department of Energy Pre-Freshman Enrichment Program 1995 Entry Form and 1996 Entry Form completed by all participants were sent to the Oak Ridge Institute for Science and Education in the fall of 1995 and 1996 respectively. Those forms are on file should they be needed. Attached also is a copy of the Summary of ideas for panel discussions, problem-solving sessions, or small group discussions presented at the Department of Energy Oak Ridge Institute for Science and Education Pre-Freshman Enrichment Program Project Directors Meeting held in San Antonio, TX, November 12--14, 1995.

Technical and economic assessment of solar hybrid repowering. Final report

Energy Technology Data Exchange (ETDEWEB)

None

1978-09-01

Public Service Company of New Mexico (PNM) has performed a Technical and Economic Assessment of Solar Hybrid Repowering under funding by the Department of Energy (DOE), the Electric Power Research Institute (EPRI), Western Energy Supply and Transmission (WEST) Associates, and a number of southwestern utilities. Solar hybrid repowering involves placement of solar hardware adjacent to and connected to existing gas- and oil-fueled electric generation units to displace some of or all the fossil fuel normally used during daylight hours. The subject study assesses the technical economic viability of the solar hybrid repowering concept within the southwestern United States and the PNM system. This document is a final report on the study and its results. The study was divided into the six primary tasks to allow a systematic investigation of the concept: (1) market survey and cost/benefit analysis, (2) study unit selection, (3) conceptual design and cost estimates, (4) unit economic analysis, (5) program planning, future phases, and (6) program management. Reeves Station No. 2 at Albuquerque, New Mexico, was selected for repowering with a design goal of 50 percent (25 MWe). The solar system design is based on the 10 MW solar central receiver pilot plant preliminary design for Barstow, California. SAN--1608-4-2 contains the technical drawings. (WHK)

University of Maryland component of the Center for Multiscale Plasma Dynamics: Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Dorland, William [University of Maryland

2014-11-18

The Center for Multiscale Plasma Dynamics (CMPD) was a five-year Fusion Science Center. The University of Maryland (UMD) and UCLA were the host universities. This final technical report describes the physics results from the UMD CMPD.

Gamma irradiator

International Nuclear Information System (INIS)

Simonet, G.

1986-09-01

Fiability of devices set around reactors depends on material resistance under irradiation noticeably joints, insulators, which belongs to composition of technical, safety or physical incasurement devices. The irradiated fuel elements, during their desactivation in a pool, are an interesting gamma irradiation device to simulate damages created in a nuclear environment. The existing facility at Osiris allows to generate an homogeneous rate dose in an important volume. The control of the element distances to irradiation box allows to control this dose rate [fr

Final report on graphite irradiation test OG-2

International Nuclear Information System (INIS)

Price, R.J.; Beavan, L.A.

1975-01-01

Results are presented of dimensional, thermal expansivity, thermal conductivity, Young's modulus, and tensile strength measurements on specimens of nuclear graphites irradiated in capsule OG-2. About half the irradiation space was allocated to H-451 near-isotropic petroleum-coke-based graphite or its subsized prototype grade H-429. Most of these specimens had been previously irradiated. Virgin specimens of another near-isotropic graphite, grade TS-1240, were irradiated. Some previously irradiated specimens of needle-coke-based H-327 graphite and pitch-coke-based P 3 JHAN were also included

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Bohdan W. Oppenheim; Rudolf Marloth

2007-10-26

Executive Summary The document contains Final Technical Report on the Industrial Assessment Center Program at Loyola Marymount University in Los Angeles, covering the contract period of 9/1/2002 to 11/30/2006, under the contract DE-FC36-02GO 12073. The Report describes six required program tasks, as follows: TASK 1 is a summary of the assessments performed over the life of the award: 77 assessments were performed, 595 AR were recommended, covering a very broad range of manufacturing plants. TASK 2 is a description of the efforts to promote and increase the adoption of assessment recommendations and employ innovative methods to assist in accomplishing these goals. The LMU IAC has been very successful in accomplishing the program goals, including implemented savings of $5,141,895 in energy, $10,045,411 in productivity and $30,719 in waste, for a total of $15,218,025. This represents 44% of the recommended savings of $34,896,392. TASK 3 is a description of the efforts promoting the IAC Program and enhancing recruitment efforts for new clients and expanded geographic coverage. LMU IAC has been very successful recruiting new clients covering Southern California. Every year, the intended number of clients was recruited. TASK 4 describes the educational opportunities, training, and other related activities for IAC students. A total of 38 students graduated from the program, including 2-3 graduate students every semester, and the remainder undergraduate students, mostly from the Mechanical Engineering Department. The students received formal weekly training in energy (75%) and productivity (25). All students underwent extensive safety training. All students praised the IAC experience very highly. TASK 5 describes the coordination and integration of the Center activities with other Center and IAC Program activities, and DOE programs. LMU IAC worked closely with MIT, and SDSU IAC and SFSU IAC, and enthusiastically supported the SEN activities. TASK 6 describes other tasks

Irradiation of spices, herbs and other vegetable seasonings: A compilation of technical data for its authorization and control

International Nuclear Information System (INIS)

1992-02-01

This publication contains a compilation of all available scientific and technical data on the irradiation of spices, herbs and other vegetable seasonings. It is intended to assist governments in considering the authorization of this particular application of radiation processing of food and in ensuring its control in the facility and the control of irradiated food products moving in trade. The Compilation was prepared in response to the requirement of the Codex General Standard for Irradiated Foods and associated Code that radiation treatment of food be justified on the basis of a technological need or of a need to improve the hygienic quality of the food. It was prepared also in response to the recommendations of the FAO/IAEA/WHO/ITC-UNCTAD/GATT International Conference on the Acceptance, Control of and Trade in Irradiated Food (Geneva, 1989) concerning the need for regulatory control of radiation processing of food. It is hoped that the information contained in this publication will assist governments in considering requests for the approval of radiation treatment of spices, herbs and other vegetable seasonings, or requests for authorization to import such irradiated products. Refs and tabs

Irradiation of sewage sludge using cesium-137: a comparative assessment

International Nuclear Information System (INIS)

1980-06-01

Irradiation using 137 CS is a recently developed process for disinfecting sewage sludge before applying it to the land. Irradiation, composting, and heat drying are Processes to Further Reduce Pathogens (PFRP) when operated to meet the guidelines set forth under Title 40, Code of the Federal Register, Part 257 (40 CFR 257). This report identifies and develops technical, operational, and environmental considerations for sludge handling systems incorporating these PFRP to determine the economic advantages of each process. The results indicate that sludge irradiation systems are cost-competitive with composting and heat drying systems for wastewater treatment plants with or without existing anaerobic digesters. Irradiation can thus be considered for new as well as upgrading existing facilities for sludge disinfection. An attractive aspect of the irradiation process is that significantly less conventional energy is used for operation when compared to composting and heat drying. In the final analysis, however, the applicability and desirability of any process is best determined by more evaluations specific to a given community

Technical relapsed testicular irradiation for acute lymphoblastic leukemia

International Nuclear Information System (INIS)

Velazquez Miranda, S.; Delgado Gil, M. M.; Ortiz Siedel, M.; Munoz Carmona, D. M.; Gomez-Barcelona, J.

2011-01-01

Testicular irradiation in children suffering from acute lymphoblastic leukemia presents difficulties in relation to daily positioning, dosimetry for dose homogenization of complex geometry and volume change during irradiation thereof. This can lead to significant deviations from the prescribed doses. In addition, the usual techniques often associated with unnecessary irradiation of pelvic simphysis, anus and perineum. This, in the case of pediatric patients, is of great importance, since doses in the vicinity of 20 Gy are associated with a deviation of bone growth, low testosterone levels around 24 Gy and high rates of generation of second tumors. To overcome these problems we propose a special restraint in prone and non-coplanar irradiation.

The application of gamma irradiation for the extended commercial storage of root crops (onions and garlic) and shipping trials of irradiated frozen shrimp. Final report for the period 1 December 1985 - 31 December 1988

International Nuclear Information System (INIS)

Nouchpromool, K.

1988-01-01

The scope of the project was to demonstrate the efficiency of pilot scale radiation treatment of onions and garlic aiming toward the transfer of food irradiation technology to traders and to evaluate the quality of irradiated frozen shrimp shipped to Japan and australia after irradiation in Thailand. The tests demonstrated that the irradiation of onions (55-94 and 74-130 Gy) and garlic (50-90 Gy) to inhibit sprouting and reduce weight loss during commercial storage in cold room is technically feasible and economically justified. The bacteriological quality of frozen, peeled, cooked shrimps was improved by radiation treatment at doses of 1.2 to 3.3 kGy. 1 fig., 15 tabs

Evaluation of Routine Atmospheric Sounding Measurements using Unmanned Systems (ERASMUS): Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

de Boer, Gijs [Univ. of Colorado, Boulder, CO (United States); Lawrence, Dale [Univ. of Colorado, Boulder, CO (United States); Palo, Scott [Univ. of Colorado, Boulder, CO (United States); Argrow, Brian [Univ. of Colorado, Boulder, CO (United States); LoDolce, Gabriel [Univ. of Colorado, Boulder, CO (United States); Curry, Nathan [Univ. of Colorado, Boulder, CO (United States); Weibel, Douglas [Univ. of Colorado, Boulder, CO (United States); Finamore, William [Univ. of Colorado, Boulder, CO (United States); D' Amore, Phillip [Univ. of Colorado, Boulder, CO (United States); Borenstein, Steven [Univ. of Colorado, Boulder, CO (United States); Nichols, Tevis [Univ. of Colorado, Boulder, CO (United States); Elston, Jack [Blackswift Technologies, Boulder, CO (United States); Ivey, Mark [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Bendure, Albert [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Schmid, Beat [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Long, Charles [Univ. of Colorado, Boulder, CO (United States); Telg, Hagen [Univ. of Colorado, Boulder, CO (United States); Gao, Ru-Shan [National Oceanic and Atmospheric Administration (NOAA), Boulder, CO (United States); Hock, Terry [National Center for Atmospheric Research, Boulder, CO (United States); Bland, Geoff [NASA Ames Research Center (ARC), Moffett Field, Mountain View, CA (United States)

2017-03-29

This final technical report details activities undertaken as part of the referenced project. Included is information on the preparation of aircraft for deployment to Alaska, summaries of the three deployments covered under this project, and a brief description of the dataset and science directions pursued. Additionally, we provide information on lessons learned, publications, and presentations resulting from this work.

Final Technical Report for contract number DE-FG02-05ER15670

Energy Technology Data Exchange (ETDEWEB)

Glazebrook, Jane [Univ. of Minnesota, Minneapolis, MN (United States)

2016-02-29

This is the final technical report for contract number DE-FG02-05ER15670. The project is now complete, and results of the project have been published. Two papers were published based on work done in the last three-year funding period. The DOIs of these papers are included below. The abstracts of the papers, providing summaries of the work, are included in the body of the report.

Technical specification: Mixed-oxide pellets for the light-water reactor irradiation demonstration test

International Nuclear Information System (INIS)

Cowell, B.S.

1997-06-01

This technical specification is a Level 2 Document as defined in the Fissile Materials Disposition Program Light-Water Reactor Mixed-oxide Fuel Irradiation Test Project Plan. It is patterned after the pellet specification that was prepared by Atomic Energy of Canada, Limited, for use by Los Alamos National Laboratory in fabrication of the test fuel for the Parallex Project, adjusted as necessary to reflect the differences between the Canadian uranium-deuterium reactor and light-water reactor fuels. This specification and the associated engineering drawing are to be utilized only for preparation of test fuel as outlined in the accompanying Request for Quotation and for additional testing as directed by Oak Ridge National Laboratory or the Department of Energy

Investigation of food irradiation technology for application to plant quarantine. Working group report of food irradiation technology

Energy Technology Data Exchange (ETDEWEB)

Sunaga, Hiromi; Ito, Hitoshi; Takatani, Yasuyuki; Takizawa, Haruki; Yotsumoto, Keiichi; Tanaka, Ryuichi [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment; Hirano, Tsuyoshi; Tokunaga, Okihiro

1999-06-01

The commercialization of food irradiation in Japan was started in 1973 for the sprout inhibition of potatoes as the first successful food irradiation facility in the world. Since approval of potato irradiation, no items has been commercialized in Japan. However, international agreement for phase out of methyl bromide after 2005 and increasing incidences of foodborn diseases such as by Escherichia coli O157:H7 are forcing to have interesting to food irradiation. Takasaki Radiation Chemistry Research Establishment has long experiences on research of irradiation effect and engineering of food irradiation in Japan. From these back ground, working group of food irradiation was organized at August 1997 by some members of Department of Radiation Research for Environment and Resources and Advanced Technology Center for supporting technically on commercialization of food irradiation. This report presents the result of discussion in working group on generalization up to date researches of food irradiation, application fields and items, technical problems and future prospects of this technology in Japan. (author)

Technical and logistic provisions for the delivery of radioactive wastes in the final repository Konrad

International Nuclear Information System (INIS)

Poeppinghaus, Jens

2013-01-01

The beginning of radioactive waste delivery to the final repository Konrad is planned for 2019. The main issue for the technical and logistic provisions is the development of a concept for the transport of the licensed radioactive waste containers to the site, including a turning concept for cylindrical waste forms and planning, construction and manufacture of transport equipment. Further issues include a logistic concept considering specific boundary conditions as administrative processes, priorities, special features of the delivering institutions and technical requirements of the repository.

Irradiated uranium reprocessing, Final report - I-IV, Part I; Prerada ozracenog urana, Zavrsni izvestaj- I-VI, I Deo

Energy Technology Data Exchange (ETDEWEB)

Gal, I [Institute of Nuclear Sciences Boris Kidric, Laboratorija za visoku aktivnost, Vinca, Beograd (Serbia and Montenegro)

1961-12-15

This volume of the final report describes the construction and functioning of the cell for dissolving the irradiated uranium. Annexes of this report describe the parts of the cell as follows: description of the metal frame, grid and stainless steel plate; container for irradiated uranium; small opening of the cell; vessel for dissolving; device for opening the cover; device for sampling of the radioactive solution, inner and outer parts; pneumatic taps.

AGR-2 Irradiation Test Final As-Run Report

Energy Technology Data Exchange (ETDEWEB)

Collin, Blaise P. [Idaho National Lab. (INL), Idaho Falls, ID (United States). VHTR Program

2014-08-01

This document presents the as-run analysis of the AGR-2 irradiation experiment. AGR-2 is the second of the planned irradiations for the Advanced Gas Reactor (AGR) Fuel Development and Qualification Program. Funding for this program is provided by the U.S. Department of Energy as part of the Very High Temperature Reactor (VHTR) Technology Development Office (TDO) program. The objectives of the AGR-2 experiment are to: 1. Irradiate UCO (uranium oxycarbide) and UO₂ (uranium dioxide) fuel produced in a large coater. Fuel attributes are based on results obtained from the AGR-1 test and other project activities. 2. Provide irradiated fuel samples for post-irradiation experiment (PIE) and safety testing. 3. Support the development of an understanding of the relationship between fuel fabrication processes, fuel product properties, and irradiation performance. The primary objective of the test was to irradiate both UCO and UO₂ TRISO (tristructural isotropic) fuel produced from prototypic scale equipment to obtain normal operation and accident condition fuel performance data. The UCO compacts were subjected to a range of burnups and temperatures typical of anticipated prismatic reactor service conditions in three capsules. The test train also includes compacts containing UO₂ particles produced independently by the United States, South Africa, and France in three separate capsules. The range of burnups and temperatures in these capsules were typical of anticipated pebble bed reactor service conditions. The results discussed in this report pertain only to U.S.-produced fuel.

Correlated charge-changing uion-atom collisions. Final Technical Report

International Nuclear Information System (INIS)

John Tanis

2005-01-01

This document comprises the final technical report for atomic collisions research supported by DOE grant No. DE-FG02-87ER13778 from September 1, 2001 through August 31, 2004. The research involved the experimental investigation of excitation and charge-changing processes occurring in ion-atom and ion-molecule collisions. Major emphases of the study were: (1) interference effects resulting from coherent electron emission in H2, (2) production of doubly vacant K-shell (hollow ion) states due to electron correlation, and (3) formation of long-lived metastable states in electron transfer processes. During the period of the grant, this research resulted in 23 publications, 12 invited presentations, and 39 contributed presentations at national and international meetings and other institutions. Brief summaries of the completed research are presented below

FERMI(at)Elettra FEL Design Technical Optimization Final Report

International Nuclear Information System (INIS)

Fawley, William; Penn, Gregory; Allaria, Enrico; De Ninno, Giovanni; Graves, William

2006-01-01

This is the final report of the FEL Design Group for the Technical Optimization Study for the FERMI(at)ELETTRA project. The FERMI(at)ELETTRA project is based on the principle of harmonic upshifting of an initial ''seed'' signal in a single pass, FEL amplifier employing multiple undulators. There are a number of FEL physics principles which underlie this approach to obtaining short wavelength output: (1) the energy modulation of the electron beam via the resonant interaction with an external laser seed (2) the use of a chromatic dispersive section to then develop a strong density modulation with large harmonic overtones (3) the production of coherent radiation by the microbunched beam in a downstream radiator. Within the context of the FERMI project, we discuss each of these elements in turn

Irradiation history and final postirradiation data for IFA-432

International Nuclear Information System (INIS)

Lanning, D.D.

1986-11-01

The irradiation history and final postirradiation examination (PIE) results are presented for the Halden fuel assembly IFA-432. In particular, the three instrumented rods (Rods 2, 3, and 5) that continued to the highest burnup (46 MWd/kgM) are emphasized. The long survival rate of the fuel instrumentation allowed a continuous record to be kept of linear heat generation rate and fuel temperatures throughout the operating history of the asembly. Fission gas release was estimated based on a combination of gas retention and ceramographic data. The PIE data show that the postirradiation condition of the rods is qualitatively consistent with the power/temperature histories experienced. Fission gas release estimates are: Rod 2 (380 μm as-fabricated gap), 20-40%; Rod 5 (230 μm as-fabricated gap), 20-40%; and Rod 3 (76 μm as-fabricated gap), 0-20%

SIMS study on statistics and environmental factors in health. Final technical report to Department of Energy

International Nuclear Information System (INIS)

1982-07-01

This final technical report to DOE consists of five individual technical reports and one working paper by members of the SIMS Study at Stanford. Research topics include testing goodness-of-fit for the distribution of errors in regression models, mathematical models of cancer and their use in risk assessment, pollutant standards index (Psi), osteosarcomas among beagles exposed to 239 Plutonium, air pollution and respiratory disease, and models of human exposure to air pollution. Individual summaries of the six reports are indexed separately

Final Technical Report DOE/GO/13142-1

Energy Technology Data Exchange (ETDEWEB)

Patrick Mulvihill; Quang Nguyen

2010-09-15

This research adds to the understanding of the areas of residual starch and biomass conversion to alcohol, by providing data from pilot plant equipment of larger scale than the minimum required to give commercially scalable data. Instrumentation and control is in place to capture the information produced, for economic and technical evaluation. The impact of rheology, recycle streams, and residence time distributions on the technical and economic performance can be assessed. Various processes can be compared technically and economically because the pilot plants are readily modifiable. Several technologies for residual starch yield improvement have been identified, implemented, and patent applications filed. Various biomass-to-ethanol processes have been compared and one selected for technical optimization and commercialization. The technical and economic feasibility of the current simplified biomass conversion process is being confirmed by intensive pilot plant efforts as of this writing. Optimization of the feedstock handling and pretreatment is occurring to increase the alcohol yield above the minimum commercially viable level already demonstrated. Samples of biomass residue and reactor blowdown condensate are being collected to determine the technical and economic performance of the high-water-recycle waste treatment system being considered for the process. The project is of benefit to the public because it is advancing the efforts to achieve low-cost fermentable substrates for conversion to transportation fuels. This process combines the hydrolysis of agricultural residues with novel enzymes and organisms to convert the sugars released to transportation fuels. The process development is taking place at a scale allowing commercial development to proceed at a rapid pace.

Stability and stabilization of polymers under irradiation. Final report of a co-ordinated research project, 1994-1997

International Nuclear Information System (INIS)

1999-01-01

The contributions presented in this technical publication describe progress in understanding and controlling the degradation of polymeric materials induced by exposure to ionizing radiation. This subject area is of widespread importance to industrial use of radiation for two classes of applications: (1) the processing and production of polymeric materials by means of irradiation facilities, and (2) the use of polymeric materials in applications for which they must withstand irradiation throughout the course of their useful lifetimes. Due to extensive and still-growing use of polymeric materials for technological applications of immense variety, and the fact that radiation-processing has the potential to play an expanding role in polymer manufacturing (current uses include crosslinking, curing, sterilization, surface modification, lithography, etc.), the ability to inhibit unwanted material property changes which often occur when materials are irradiated, and to predict useful lifetimes, remains a limiting factor in a number of existing radiation technologies. Additionally, the ability to control unwanted degradation will be necessary for successful implementation of future, more advanced, radiation processing schemes. This co-ordinated research project (CRP) was established for the purpose of focusing the attention of appropriate technical experts on the complex task of establishing a better fundamental basis for understanding and attacking problems or radiation degradation of materials. The group dynamics have been designed to achieve a synergistic interaction among worldwide research facilities for the purposes of identifying degradation problems, exchanging ideas and results on the solution of these problems, and making the emerging information available in an organized and accessible format. From this meeting, it is clear that much remains to be learnt in terms of understanding degradation mechanisms and phenomena. It also appears that important new

Evaluation of irradiated sewage sludges; Evaluacion de la irradiacion de lodos residuales

Energy Technology Data Exchange (ETDEWEB)

Colin C, A

1994-12-31

The residual muds are produced by a separation process in the black waters treatment constituted by a solid phase whose origin is the accumulation of pollutant matter that has been extended to the water for anthropogenic and/or natural activities. The present work has the purpose to carry out a technical evaluation for the irradiation process of residual muds for their possible application like alternative of treatment and final disposal. The results obtained for the Evaluation of the irradiation of residual muds are bounded with the federative entities in the study, on the number of treatment plants of residual waters by diverse methods, discharge types, system location, residual muds production and muds treatment, uses and final disposal. The results show in the several entities,a great variety and versatility of industrial branches with diverse systems for treatment of waters and scarceness in the systems for residual muds treatment. (Author).

DOE FINAL TECHNICAL REPORT RP

Energy Technology Data Exchange (ETDEWEB)

RUSS PETERMAN

2012-01-01

The City of Georgetown Utility Systems (GUS) patnered with the private sector, the American Public Power Association (APPA) and Southwestern University to design, construct, test and monitor a solar co-generation system directly connected to the GUS electric distribution system. This report consists of the Primary Technical Report and 3 attachments.

Questionnaire survey and technical guideline of blood irradiation on medical facilities

International Nuclear Information System (INIS)

Matsumoto, Mitsuhiro; Hasegawa, Hironori; Okumura, Masahiko; Sonoda, Tatsuo; Osada, Koji.

1997-01-01

We know that transfusion-associated graft versus host disease (TA-GVHD) is a serious side effect associated with blood transfusion and the onset is independent on the immunological conditions of patients. We have only prophylactic treatment against TA-GVHD. The most reliable method is to irradiate the blood for transfusion. In Japanese medical facilities, however, the risk of TA-GVHD is poorly understood and actual conditions of the blood irradiation are unclear. We sent a questionnaire to randomly selected 426 medical facilities in Japan, which had the department of radiology, to investigate the actual conditions of blood irradiation for transfusion and the problems on the irradiation dose measurement of the external apparatus for blood irradiation. The questionnaire involved 19 questions about the blood irradiation for transfusion. The survey took place for one month (June 1-June 30, 1995). Replies were obtained from a total of 306 medical facilities (72%). The results showed that blood irradiation was done by several methods in the 75% of the medical facilities, and the external irradiation apparatus was used in 83%. Some problems were shown, including irradiation period, cost of the irradiation, the operating procedure of the apparatus, requested number of the irradiation, and the request after usual hours. There was no significant problem on the irradiation dose, irradiation method, etc. We also sent a questionnaire to 74 facilities of the Red Cross Blood Center, in which the frequency of blood irradiation have increased since May, 1976. The X-ray apparatus as the external irradiation apparatus has practical advantages; lower cost, compact and out of the legal control on the ionizing radiation, however, it has some problems on the uniformity of the absorption dose when a single X-ray tube-type apparatus is used. We discuss about the possible onset of TA-GVHD or other accidents by the incorrect irradiation of the blood preparations. (K.H.)

Technical support document for the surface disposal of sewage sludge. Final report

International Nuclear Information System (INIS)

1992-11-01

The document provides the technical background and justification for the U.S. Environmental Protection Agency's (EPA) final regulation (40 CFR Part 503) covering the surface disposal of sewage sludge. The document summarizes current practices in land application and presents data supporting the risk assessment methodology used to derive human health and environmental risk-based limits for contaminants in sewage sludge placed on surface disposal sites. The management practices associated with surface disposal are outlined and the different pathways by which contaminants reach highly-exposed individuals (HEIs) through surface disposal are discussed

Technical support document for the surface disposal of sewage sludge. Final report

Energy Technology Data Exchange (ETDEWEB)

1992-11-01

The document provides the technical background and justification for the U.S. Environmental Protection Agency's (EPA) final regulation (40 CFR Part 503) covering the surface disposal of sewage sludge. The document summarizes current practices in land application and presents data supporting the risk assessment methodology used to derive human health and environmental risk-based limits for contaminants in sewage sludge placed on surface disposal sites. The management practices associated with surface disposal are outlined and the different pathways by which contaminants reach highly-exposed individuals (HEIs) through surface disposal are discussed.

Technical assistance contractor Management Plan. Final [report

Energy Technology Data Exchange (ETDEWEB)

1993-09-01

The Technical Assistance Contractor (TAC) for the Uranium Mill Tailings Remedial Action (UMTRA) Project comprises Jacobs Engineering Group Inc. (JEG) and its major teaming partners [Roy F. Weston, Inc. (RFW), Sergent, Hauskins & Beckwith Agra, Inc. (SHB Agra), and Geraghty & Miller, Inc. (G&M)]. The first three companies have worked together effectively on the UMTRA Project for more than 10 years. With the initiation of the UMTRA Groundwater Project in April 1991, a need arose to increase the TAC`s groundwater technical breadth and depth, so G&M was brought in to augment the team`s capabilities. The TAC contract`s scope is to provide technical, analytical, environmental, engineering, design, inspection, and management support services to the US Department of Energy (DOE) for both surface and groundwater projects. The TAC team continues to support the DOE in completing surface remedial actions and initiating groundwater remediation work for start-up, characterization, design, construction oversight, and remedial operations. A key feature of the TAC`s management approach is the extensive set of communication systems implemented for the UMTRA Project. These systems assist all functional disciplines in performing UMTRA Project tasks associated with management, technical support, administrative support, and financial/project controls.

Experimental Program Final Technical Progress Report: 15 February 2007 to 30 September 2012

Energy Technology Data Exchange (ETDEWEB)

Kinney, Edward R. [University of Colorado, Boulder, CO

2014-09-12

This is the final technical report of the grant DE-FG02-04ER41301 to the University of Colorado at Boulder entitled "Intermediate Energy Nuclear Physics" and describes the results of our funded activities during the period 15 February 2007 to 30 September 2012. These activities were primarily carried out at Fermilab, RHIC, and the German lab DESY. Significant advances in these experiments were carried out by members of the Colorado group and are described in detail.

Food irradiation: fiction and reality

International Nuclear Information System (INIS)

1991-01-01

The International Consultative Group on Food Irradiation (IGCFI), sponsored by World Health Organization (WHO), Food and Agriculture Organization (FAO) and the International Atomic Energy Agency (IAEA), with the intention to provide to governments, especially those of developing countries, scientifically correct information about food irradiation, decided to organize a file and questions of general public interest. The document is composed by descriptive files related with the actual situation and future prospective, technical and scientific terms, food irradiation and the radioactivity, chemical transformations in irradiated food, genetic studies, microbiological safety of irradiated food, irradiation and harmlessness, irradiation and additives, packing, irradiation facilities control, process control, irradiation costs and benefits as well as consumers reaction

Technical Report - FINAL

Energy Technology Data Exchange (ETDEWEB)

Barbara Luke, Director, UNLV Engineering Geophysics Laboratory

2007-04-25

Improve understanding of the earthquake hazard in the Las Vegas Valley and to assess the state of preparedness of the area's population and structures for the next big earthquake. 1. Enhance the seismic monitoring network in the Las Vegas Valley 2. Improve understanding of deep basin structure through active-source seismic refraction and reflection testing 3. Improve understanding of dynamic response of shallow sediments through seismic testing and correlations with lithology 4. Develop credible earthquake scenarios by laboratory and field studies, literature review and analyses 5. Refine ground motion expectations around the Las Vegas Valley through simulations 6. Assess current building standards in light of improved understanding of hazards 7. Perform risk assessment for structures and infrastructures, with emphasis on lifelines and critical structures 8. Encourage and facilitate broad and open technical interchange regarding earthquake safety in southern Nevada and efforts to inform citizens of earthquake hazards and mitigation opportunities

An Approach to Developing Independent Learning and Non-Technical Skills Amongst Final Year Mining Engineering Students

Science.gov (United States)

Knobbs, C. G.; Grayson, D. J.

2012-01-01

There is mounting evidence to show that engineers need more than technical skills to succeed in industry. This paper describes a curriculum innovation in which so-called "soft" skills, specifically inter-personal and intra-personal skills, were integrated into a final year mining engineering course. The instructional approach was…

Final Technical Report for SISGR: Ultrafast Molecular Scale Chemical Imaging

Energy Technology Data Exchange (ETDEWEB)

Hersam, Mark C. [Northwestern Univ., Evanston, IL (United States). Dept. of Materials Science and Engineering; Guest, Jeffrey R. [Argonne National Lab. (ANL), Argonne, IL (United States). Center for Nanoscale Materials; Guisinger, Nathan P. [Argonne National Lab. (ANL), Argonne, IL (United States). Center for Nanoscale Materials; Hla, Saw Wai [Argonne National Lab. (ANL), Argonne, IL (United States). Center for Nanoscale Materials; Schatz, George C. [Northwestern Univ., Evanston, IL (United States). Dept. of Chemistry; Seideman, Tamar [Northwestern Univ., Evanston, IL (United States). Dept. of Chemistry; Van Duyne, Richard P. [Northwestern Univ., Evanston, IL (United States). Dept. of Chemistry

2017-04-10

The Northwestern-Argonne SISGR program utilized newly developed instrumentation and techniques including integrated ultra-high vacuum tip-enhanced Raman spectroscopy/scanning tunneling microscopy (UHV-TERS/STM) and surface-enhanced femtosecond stimulated Raman scattering (SE-FSRS) to advance the spatial and temporal resolution of chemical imaging for the study of photoinduced dynamics of molecules on plasmonically active surfaces. An accompanying theory program addressed modeling of charge transfer processes using constrained density functional theory (DFT) in addition to modeling of SE-FSRS, thereby providing a detailed description of the excited state dynamics. This interdisciplinary and highly collaborative research resulted in 62 publications with ~ 48% of them being co-authored by multiple SISGR team members. A summary of the scientific accomplishments from this SISGR program is provided in this final technical report.

JOYO-1 Irradiation Test Campaign Technical Close-out, For Information

International Nuclear Information System (INIS)

G. Borges

2006-01-01

The JOYO-1 irradiation testing was designed to screen the irradiation performance of candidate cladding, structural and reflector materials in support of space reactor development. The JOYO-1 designation refers to the first of four planned irradiation tests in the JOYO reactor. Limited irradiated material performance data for the candidate materials exists for the expected Prometheus-1 duration, fluences and temperatures. Materials of interest include fuel element cladding and core materials (refractory metal alloys and silicon carbide (Sic)), vessel and plant structural materials (refractory metal alloys and nickel-base superalloys), and control and reflector materials (BeO). Key issues to be evaluated were long term microstructure and material property stability. The JOYO-1 test campaign was initiated to irradiate a matrix of specimens at prototypical temperatures and fluences anticipated for the Prometheus-1 reactor [Reference (1)]. Enclosures 1 through 9 describe the specimen and temperature monitors/dosimetry fabrication efforts, capsule design, disposition of structural material irradiation rigs, and plans for post-irradiation examination. These enclosures provide a detailed overview of Naval Reactors Prime Contractor Team (NRPCT) progress in specific areas; however, efforts were in various states of completion at the termination of NRPCT involvement with and restructuring of Project Prometheus

JOYO-1 Irradiation Test Campaign Technical Close-out, For Information

Energy Technology Data Exchange (ETDEWEB)

G. Borges

2006-01-31

The JOYO-1 irradiation testing was designed to screen the irradiation performance of candidate cladding, structural and reflector materials in support of space reactor development. The JOYO-1 designation refers to the first of four planned irradiation tests in the JOYO reactor. Limited irradiated material performance data for the candidate materials exists for the expected Prometheus-1 duration, fluences and temperatures. Materials of interest include fuel element cladding and core materials (refractory metal alloys and silicon carbide (Sic)), vessel and plant structural materials (refractory metal alloys and nickel-base superalloys), and control and reflector materials (BeO). Key issues to be evaluated were long term microstructure and material property stability. The JOYO-1 test campaign was initiated to irradiate a matrix of specimens at prototypical temperatures and fluences anticipated for the Prometheus-1 reactor [Reference (1)]. Enclosures 1 through 9 describe the specimen and temperature monitors/dosimetry fabrication efforts, capsule design, disposition of structural material irradiation rigs, and plans for post-irradiation examination. These enclosures provide a detailed overview of Naval Reactors Prime Contractor Team (NRPCT) progress in specific areas; however, efforts were in various states of completion at the termination of NRPCT involvement with and restructuring of Project Prometheus.

Advantage of irradiation in food industry, technical and economical constraints

International Nuclear Information System (INIS)

Dupuy, P.

1986-01-01

Irradiation is an effective method to extend the conservation and to increase the hygienic security of food. Nevertheless the use of irradiation remains limited in food industry. The prospects of different applications are evaluated, referring to the other alternative technologies. The advantage of adequate irradiation facilities incorporated or not into the plants are compared [fr

Food irradiation. Technical and legal aspects

International Nuclear Information System (INIS)

Vas, K.

1978-01-01

This document presents a brief technical discussion on a new major technique for food preservation and points out the necessary harmonization of national regulations to give them a broader application field [fr

Final report on graphite irradiation test OG-3

International Nuclear Information System (INIS)

Price, R.J.; Beavan, L.A.

1977-01-01

The results of dimensional, thermal expansivity, thermal conductivity, Young's modulus, and tensile strength measurements on graphite specimens irradiated in capsule OG-3 are presented. The graphite grades investigated included near-isotropic H-451 (three different preproduction lots), TS-1240, and SO818; needle coke H-327; and European coal tar pitch coke grades P 3 JHA 2 N, P 3 JHAN, and ASI2-500. Data were obtained in the temperature range 823 0 K to 1673 0 K. The peak fast neutron fluence in the experiment was 3 x 10 25 n/m 3 (E greater than 29 fJ)/sub HTGR/; the total accumulated fluence exceeded 9 x 10 25 n/m 2 on some H-451 specimens and 6 x 10 25 n/m 2 on some TS-1240 specimens. Irradiation-induced dimensional changes on H-451 graphite differed slightly from earlier predictions. For an irradiation temperature of about 1225 0 K, axial shrinkage rates at high fluences were somewhat higher than predicted, and the fluence at which radial expansion started (about 9 x 10 25 n/m 2 at 1275 0 K) was lower. TS-1240 graphite underwent smaller dimensional changes than H-451 graphite, while limited data on SO818 and ASI2-500 graphites showed similar behavior to H-451. P 3 JHAN and P 3 JHA 2 N graphites displayed anisotropic behavior with rapid axial shrinkage. Comparison of dimensional changes between specimens from three logs of H-451 and of TS-1240 graphites showed no significant log-to-log variations for H-451, and small but significant log-to-log variations for TS-1240. The thermal expansivity of the near-isotropic graphites irradiated at 865-1045 0 K first increased by 5 percent to 10 percent and then decreased. At higher irradiation temperatures the thermal expansivity decreased by up to 50 percent. Changes in thermal conductivity were consistent with previously established curves. Specimens which were successively irradiated at two different temperatures took on the saturation conductivity for the new temperature

IAEA International Database on Irradiated Nuclear Graphite Properties. 7th meeting of the Technical Steering Committee

International Nuclear Information System (INIS)

Humbert, D.; Wickham, A.J.

2005-06-01

This report summarizes the Consultant Meeting '7th Meeting of the Technical Steering Committee for the International Database on Irradiated Nuclear Graphite Properties' held on 16-17 March 2005 at the IAEA Headquarters, Vienna, Austria. The purposes of the meeting were to review the matters and actions identified in the previous meeting, undertake a review of the current status of the database and to make recommendations for actions for the next year. The purposes of the meeting were fully met. This report contains the current status of the identified actions as well as a summary of the recommendations on enhancements to the database. (author)

IAEA International Database on Irradiated Nuclear Graphite Properties. 6th meeting of the Technical Steering Committee

International Nuclear Information System (INIS)

Humbert, D.; Wickham, A.J.

2004-12-01

This report summarizes the Consultant Meeting 6th Meeting of the Technical Steering Committee for the International Database on Irradiated Nuclear Graphite Properties' held on 16-17 September 2004 at Plas Tan-Y-Bwlch, Maentwrog, Gwynedd, UK. The purposes of the meeting were to review the matters and actions identified in the previous meeting, undertake a review of the current status of the database and to make recommendations for actions for the next year. The purposes of the meeting were fully met. This report contains the current status of the identified actions as well as a summary of the recommendations on enhancements to the database. (author)

Dosimetry and irradiation methods for the ANSTO gamma technology research irradiator (GATRI)

International Nuclear Information System (INIS)

Izard, M.E.

1988-07-01

The Australian Nuclear Science and Technology Organisation's gamma technology research irradiator (GATRI) at Lucas Heights, New South Wales, has been modified for use as a research and small-scale commercial irradiation facility to be available to government agencies and private industry for the technical and economic evaluation of irradiation processing. The new source rack was designed around existing mechanical components to optimise the limited space available within the irradiation cell. Irradiation parameters investigated during commissioning included the effect of source-to-target distance on relative dose rates within targets of the same density; effect of density on dose-rate distribution within targets irradiated at the same distance from the source; and the contribution of transit dose to low absorbed doses as the source is raised and lowered. The efficiency of the irradiator was determined for various target densities and overdose ratios

DIMEC - Final Report

DEFF Research Database (Denmark)

Conrad, Finn

1997-01-01

Final report of the research project DIMEC - Danish InfoMechatronic Control supported by the Danish Technical Research Council, STVF.......Final report of the research project DIMEC - Danish InfoMechatronic Control supported by the Danish Technical Research Council, STVF....

Recent developments in post-irradiation examination techniques for water reactor fuel. Proceedings of a technical committee meeting held in Cadarache, France, 17-21 October 1994

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

At the invitation of the Government of France, following a proposal of the International Working Group on Water Reactor Fuel Performance and Technology (IWGFPT) the IAEA convened a Technical Committee meeting from 14 to 21 October 1994 in Cadarache to discuss recent technical advances and improvements in the field of post-irradiation examination (PIE) of fuel used in nuclear power plants. Fifty participants representing 14 countries attended the meeting and 30 papers were presented and discussed during five technical sessions. Working Groups composed of the session chairmen and authors of papers prepared summaries of each session including conclusions and recommendations for future work. Refs, figs and tabs.

Recent developments in post-irradiation examination techniques for water reactor fuel. Proceedings of a technical committee meeting held in Cadarache, France, 17-21 October 1994

International Nuclear Information System (INIS)

1995-09-01

At the invitation of the Government of France, following a proposal of the International Working Group on Water Reactor Fuel Performance and Technology (IWGFPT) the IAEA convened a Technical Committee meeting from 14 to 21 October 1994 in Cadarache to discuss recent technical advances and improvements in the field of post-irradiation examination (PIE) of fuel used in nuclear power plants. Fifty participants representing 14 countries attended the meeting and 30 papers were presented and discussed during five technical sessions. Working Groups composed of the session chairmen and authors of papers prepared summaries of each session including conclusions and recommendations for future work. Refs, figs and tabs

Final Technical Report: Hydrogen Codes and Standards Outreach

Energy Technology Data Exchange (ETDEWEB)

Hall, Karen I.

2007-05-12

This project contributed significantly to the development of new codes and standards, both domestically and internationally. The NHA collaborated with codes and standards development organizations to identify technical areas of expertise that would be required to produce the codes and standards that industry and DOE felt were required to facilitate commercialization of hydrogen and fuel cell technologies and infrastructure. NHA staff participated directly in technical committees and working groups where issues could be discussed with the appropriate industry groups. In other cases, the NHA recommended specific industry experts to serve on technical committees and working groups where the need for this specific industry expertise would be on-going, and where this approach was likely to contribute to timely completion of the effort. The project also facilitated dialog between codes and standards development organizations, hydrogen and fuel cell experts, the government and national labs, researchers, code officials, industry associations, as well as the public regarding the timeframes for needed codes and standards, industry consensus on technical issues, procedures for implementing changes, and general principles of hydrogen safety. The project facilitated hands-on learning, as participants in several NHA workshops and technical meetings were able to experience hydrogen vehicles, witness hydrogen refueling demonstrations, see metal hydride storage cartridges in operation, and view other hydrogen energy products.

Final environmental statement concerning rule making. Exemption from licensing requirements for spark-gap irradiators that contain cobalt-60. Docket No. PRM 30-54

International Nuclear Information System (INIS)

1977-12-01

The potential environmental impacts and adverse environmental effects from distribution, use only in commercial-sized oil burners, and disposal of 6000 spark-gap irradiators per year that contain 60 Co are summarized. On the basis of the analysis and evaluation set forth in this statement and after weighing the environmental, economic, technical, and other benefits against environmental costs and after considering available alternatives, it is concluded that the action called for under the National Environmental Policy Act of 1969 (NEPA) and 10 CFR Part 51 is the issuance of an exemption from licensing requirements for spark-gap irradiators that contain 60 Co, subject to the following conditions for the protection of the environment: persons who apply 60 Co to, or persons who incorporate 60 Co into, spark-gap irradiators or persons who import for sale or distribution spark-gap irradiators containing 60 Co are not exempt from the requirements for a license; each spark-gap irradiator shall contain no more than 1 μCi of 60 Co; and the 60 Co shall be applied to the spark-gap irradiators for use in electrically ignited fuel-oil burners having a firing rate of at least 3 gal/h

Technical support document for land application of sewage sludge. Volume 1. Final report

International Nuclear Information System (INIS)

Jones, A.; Beyer, L.; Rookwood, M.; Pacenka, J.; Bergin, J.

1992-11-01

The document provides the technical background and justification for the U.S. Environmental Protection Agency's (EPA) final regulation (40 CFR Part 503) covering the land application of sewage sludge. The document summarizes current practices in land application and presents data supporting the risk assessment methodology used to derive human health and environmental risk-based limits for contaminants in land applied sewage sludge. The management practices associated with land application are outlined and the different pathways by which contaminants reach highly-exposed individuals (HEIs) through land application are discussed

Hot Cell Post-Irradiation Examination and Poolside Inspection of Nuclear Fuel. Proceedings of the IAEA-HOTLAB Technical Meeting

International Nuclear Information System (INIS)

2013-04-01

The growing operational requirements for nuclear fuel, such as longer fuel cycles, higher burnups and wider use of transient regimes, require more robust fuel designs and more radiation resistant materials. Development of such advanced fuels is only possible with testing and analysis of their performance and application of adequate post-irradiation examination (PIE) methods and techniques. In addition, operational feedback data from poolside and PIE facilities are absolutely necessary for verification of fuel modelling codes and analysis of fuel failure mechanisms. For these reasons, the International Atomic Energy Agency (IAEA) has supported the international exchange of knowledge and sharing of best practices in the application of modern destructive and non-destructive methods of investigation of highly radioactive materials through a series of technical meetings (TMs), the last of which was held in 2006 in Buenos Aires. Since 1963, similar meetings, initially at the European level, have been organized by the Hot Laboratories and Remote Handling Working Group (HOTLAB), a partner in the development of the IAEA's Post Irradiation Examination Facilities Database (PIEDB), part of the IAEA's Integrated Nuclear Fuel Cycle Information System. With this successful partnership in mind, in 2010 the IAEA Technical Working Group on Fuel Performance and Technology recommended that a joint IAEA-HOTLAB TM be held on 'Hot Cell Post-Irradiation Examination and Pool-Side Inspection of Nuclear Fuel', covering questions relevant to the IAEA sub-programmes on 'Nuclear Power Reactor Fuel Engineering' and 'Management of Spent Fuel from Nuclear Power Reactors'. The TM was held on 23-27 May 2011, in Smolenice, Slovakia, with the participation of a large number of interested organizations and comprehensive coverage of major PIE and poolside inspection issues relating to both operation and storage of fuel for nuclear power reactors. The proceedings, summaries and conclusions of that joint

Irradiated nuclear fuel transport from Japan to Europe

International Nuclear Information System (INIS)

Kavanagh, M.T.; Shimoyama, S.

1976-01-01

Irradiated nuclear fuel has been transported from Japan to Europe since 1969, although U.K. experience goes back almost two decades. Both magnox and oxide fuel have been transported, and the technical requirements associated with each type of fuel are outlined. The specialized ships used by British Nuclear Fuels Limited (BNFL) for this transport are described, as well as the ships being developed for future use in the Japan trade. The ship requirements are related to the regulatory position both in the United Kingdom and internationally, and the Japanese regulatory requirements are described. Finally, specific operational experience of a Japanese reactor operator is described

Irradiation-Accelerated Corrosion of Reactor Core Materials. Final Report

Energy Technology Data Exchange (ETDEWEB)

Jiao, Zhujie [Univ. of Michigan, Ann Arbor, MI (United States); Was, Gary [Univ. of Michigan, Ann Arbor, MI (United States); Bartels, David [Univ. of Notre Dame, IN (United States)

2015-04-02

This project aims to understand how radiation accelerates corrosion of reactor core materials. The combination of high temperature, chemically aggressive coolants, a high radiation flux and mechanical stress poses a major challenge for the life extension of current light water reactors, as well as the success of most all GenIV concepts. Of these four drivers, the combination of radiation and corrosion places the most severe demands on materials, for which an understanding of the fundamental science is simply absent. Only a few experiments have been conducted to understand how corrosion occurs under irradiation, yet the limited data indicates that the effect is large; irradiation causes order of magnitude increases in corrosion rates. Without a firm understanding of the mechanisms by which radiation and corrosion interact in film formation, growth, breakdown and repair, the extension of the current LWR fleet beyond 60 years and the success of advanced nuclear energy systems are questionable. The proposed work will address the process of irradiation-accelerated corrosion that is important to all current and advanced reactor designs, but remains very poorly understood. An improved understanding of the role of irradiation in the corrosion process will provide the community with the tools to develop predictive models for in-reactor corrosion, and to address specific, important forms of corrosion such as irradiation assisted stress corrosion cracking.

Combination processes for food irradiation. Proceedings of the final research co-ordination meeting

International Nuclear Information System (INIS)

1998-01-01

There is an increasing consumer demand for food that is safe, minimally processed, visually attractive, full flavoured, nutritious, and convenient to prepare and serve, that has fewer preservatives, and that is available throughout the year at an affordable cost. Consumer concern and regulatory restrictions on the use of preservatives and pesticides in food are adversely affecting international trade in many food products. As a result, minimally processed, chilled foods and ready to eat foods are increasingly being marketed to satisfy consumer demand in both developed and developing countries. However, such foods could introduce new microbiological risks to the population, especially to those who are immunocompromised or generally at risk (children, pregnant women, the elderly, etc.). In view of these factors, a 5 year Co-ordinated Research Programme (CRP) on Irradiation in Combination with Other Processes for Improving Food Quality was initiated in 1991 by the Food and Agriculture Organization of the United Nations and the International Atomic Energy Agency through their Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture. The objectives of this CRP were to evaluate: 1) Combination treatment involving irradiation in order to extend the self-life of meat, seafood, fruits and vegetables at refrigeration temperatures and under ambient conditions; 2) Combination treatment involving irradiation in order to ensure the microbiological safety of foods, both individual and composite, including prepared meals; 3) Shelf-life extension of chilled, prepared meals and the development of shelf stable food and food components through combination treatment involving irradiation; 4) Energy requirements of combination processes involving irradiation in comparison to other food processes. Scientists from 14 countries participated in the CRP by carrying out the work under Research Contracts and Agreements with the Joint FAO/IAEA Division. The first Research Co

Final Technical Progress Report: Development of Low-Cost Suspension Heliostat; December 7, 2011 - December 6, 2012

Energy Technology Data Exchange (ETDEWEB)

Bender, W.

2013-01-01

Final technical progress report of SunShot Incubator Solaflect Energy. The project succeeded in demonstrating that the Solaflect Suspension Heliostat design is viable for large-scale CSP installations. Canting accuracy is acceptable and is continually improving as Solaflect improves its understanding of this design. Cost reduction initiatives were successful, and there are still many opportunities for further development and further cost reduction.

Commercial implementation of food irradiation

International Nuclear Information System (INIS)

Welt, M.A.

1985-01-01

Recent positive developments in regulatory matters involving food irradiation appear to be opening the door to commercial implementation of the technology. Experience gained over five years in operating multi-purpose food irradiation facilities in the United States have demonstrated the technical and economic feasibility of the radiation preservation of food for a wide variety of purposes. Public education regarding food irradiation has been intensified especially with the growing favorable involvement of food trade associations, the USDA, and the American Medical Association. After 41 years of development effort, food irradiation will become a commercial reality in 1985. (author)

Food irradiation from a scientific point of view

International Nuclear Information System (INIS)

Diehl, J.F.

1989-01-01

Tests have been carried out in the Federal Republic of Germany in recent years to determine what technical possibilities are offered by food irradiation, whether the consumption of irradiated food is safe and what methods can be developed for identifying successful cases of irradiation. The author looks into these matters and comes to the conclusion that public reporting of food irradiation is misleading. (DG) [de

Food irradiation

International Nuclear Information System (INIS)

1991-01-01

Processing of food with low levels of radiation has the potential to contribute to reducing both spoilage of food during storage - a particular problem in developing countries - and the high incidence of food-borne disease currently seen in all countries. Approval has been granted for the treatment of more than 30 products with radiation in over 30 countries but, in general, governments have been slow to authorize the use of this new technique. One reason for this slowness is a lack of understanding of what food irradiation entails. This book aims to increase understanding by providing information on the process of food irradiation in simple, non-technical language. It describes the effects that irradiation has on food, and the plant and equipment that are necessary to carry it out safely. The legislation and control mechanisms required to ensure the safety of food irradiation facilities are also discussed. Education is seen as the key to gaining the confidence of the consumers in the safety of irradiated food, and to promoting understanding of the benefits that irradiation can provide. (orig.) With 4 figs., 1 tab [de

NEET-AMM Final Technical Report on Laser Direct Manufacturing (LDM) for Nuclear Power Components

International Nuclear Information System (INIS)

Anderson, Scott; Baca, Georgina; O'Connor, Michael

2015-01-01

Final technical report summarizes the program progress and technical accomplishments of the Laser Direct Manufacturing (LDM) for Nuclear Power Components project. A series of experiments varying build process parameters (scan speed and laser power) were conducted at the outset to establish the optimal build conditions for each of the alloys. Fabrication was completed in collaboration with Quad City Manufacturing Laboratory (QCML). The density of all sample specimens was measured and compared to literature values. Optimal build process conditions giving fabricated part densities close to literature values were chosen for making mechanical test coupons. Test coupons whose principal axis is on the x-y plane (perpendicular to build direction) and on the z plane (parallel to build direction) were built and tested as part of the experimental build matrix to understand the impact of the anisotropic nature of the process.. Investigations are described 316L SS, Inconel 600, 718 and 800 and oxide dispersion strengthed 316L SS (Yttria) alloys.

NEET-AMM Final Technical Report on Laser Direct Manufacturing (LDM) for Nuclear Power Components

Energy Technology Data Exchange (ETDEWEB)

Anderson, Scott [Lockheed Martin Corporation, Denver, CO (United States). Space Systems Company; Baca, Georgina [Lockheed Martin Corporation, Denver, CO (United States). Space Systems Company; O' Connor, Michael [Lockheed Martin Corporation, Denver, CO (United States). Space Systems Company

2015-12-31

Final technical report summarizes the program progress and technical accomplishments of the Laser Direct Manufacturing (LDM) for Nuclear Power Components project. A series of experiments varying build process parameters (scan speed and laser power) were conducted at the outset to establish the optimal build conditions for each of the alloys. Fabrication was completed in collaboration with Quad City Manufacturing Laboratory (QCML). The density of all sample specimens was measured and compared to literature values. Optimal build process conditions giving fabricated part densities close to literature values were chosen for making mechanical test coupons. Test coupons whose principal axis is on the x-y plane (perpendicular to build direction) and on the z plane (parallel to build direction) were built and tested as part of the experimental build matrix to understand the impact of the anisotropic nature of the process.. Investigations are described 316L SS, Inconel 600, 718 and 800 and oxide dispersion strengthed 316L SS (Yttria) alloys.

Technical Report for a Study on the Improvement of Extraction Process and Physiological Activities of Polysaccharides from Undaria pinnatifida by Gamma Irradiation

International Nuclear Information System (INIS)

Choi, Jong Il; Lee, Ju Won; Kim, Jae Hun; Yoon, Yo Han; Song, Beom Seok; Yoon, Min Chul; Sung, Nak Yun; Lee, Hak Jyung

2010-06-01

By reason of Undaria pinnatifida growth is temperature dependent, U. pinnatifida produced in April and May are obtained as the main byproducts and it is normally wasted. The objective of the this study was investigated to the improvement of extraction process and physiological activities of polysaccharides from U. pinnatifida by gamma irradiation. The extraction yield of fucoidan and laminarrin was increased by gamma irradiation, and the molecular weight of extracted polysaccharides was decreased by irradiation. The effect of gamma irradiation on storage of U. pinnatifida was investigated. No viable cells were observed in samples irradiated at 3 and 5 kGy. Finally, fucoidan and laminarin were applied in the pork patty, and it was shown that lower lipid oxidation and positive effect on microbial stability and quality of the pork patty. These results will suggest that radiation technology can be applied for the extraction of functional materials and storages safe of the seaweeds

AGC-3 Experiment Irradiation Monitoring Data Qualification Final Report

Energy Technology Data Exchange (ETDEWEB)

Laurence Hull

2014-10-01

The Graphite Technology Development Program will run a series of six experiments to quantify the effects of irradiation on nuclear grade graphite. The third experiment, Advanced Graphite Creep 3 (AGC 3), began with Advanced Test Reactor (ATR) Cycle 152B on November 27, 2012, and ended with ATR Cycle 155B on April 23, 2014. This report documents qualification of AGC 3 experiment irradiation monitoring data for use by the Very High Temperature Reactor (VHTR) Technology Development Office (TDO) Program for research and development activities required to design and license the first VHTR nuclear plant. Qualified data meet the requirements for data collection and use as described in the experiment planning and quality assurance documents. Failed data do not meet the requirements. Trend data may not meet the requirements, but may still provide some useable information. All thermocouples (TCs) functioned throughout the AGC 3 experiment. There was one interval between December 18, 2012, and December 20, 2012, where 10 NULL values were reported for various TCs. These NULL values were deleted from the Nuclear Data Management and Analysis System database. All temperature data are Qualified for use by the VHTR TDO Program. Argon, helium, and total gas flow data were within expected ranges and are Qualified for use by the VHTR TDO Program. Total gas flow was approximately 50 sccm through the AGC 3 experiment capsule. Helium gas flow was briefly increased to 100 sccm during ATR shutdowns. At the start of the AGC 3 experiment, moisture in the outflow gas line was stuck at a constant value of 335.6174 ppmv for the first cycle (Cycle 152B). When the AGC 3 experiment capsule was reinstalled in ATR for Cycle 154B, a new moisture filter was installed. Moisture data from Cycle 152B are Failed. All moisture data from the final three cycles (Cycles 154B, 155A, and 155B) are Qualified for use by the VHTR TDO Program.

RECH-1 test fuel irradiation status report

International Nuclear Information System (INIS)

Marin, J.; Lisboa, J.; Olivares, L.; Chavez, J.

2005-01-01

Since May 2003, one RECH-1 fuel element has been submitted to irradiation at the HFR-Petten, Holland. By November 2004 the irradiation has achieved its pursued goal of 55% burn up. This irradiation qualification service will finish in the year 2005 with PIE tests, as established in a contractual agreement between the IAEA, NRG, and CCHEN. This report presents the objectives and the current results of this fuel qualification under irradiation. Besides, a brief description of CHI/4/021, IAEA's Technical Cooperation Project that has supported this irradiation test, is also presented here. (author)

Position paper on irradiated fuel and waste management. The Achille's heel of the nuclear industry?

International Nuclear Information System (INIS)

Bonin, Bernard

2014-01-01

The management and final disposal of irradiated fuel and nuclear waste is often presented by the media and perceived by the public as being an unsolved problem that restricts the future of nuclear energy. However, the nuclear industry focused on this problem very early on and has developed proven technical solutions. Nuclear energy will continue developing worldwide, in spite of the Fukushima accident. Even in those European countries that have decided to phase-out nuclear energy there is a legacy of nuclear waste that must be dealt with. The scientific and technical expertise needed for waste management already exists. Management decisions must be taken. Now is the time for political courage. (orig.)

AGR 3/4 Irradiation Test Final As Run Report

Energy Technology Data Exchange (ETDEWEB)

Collin, Blaise P. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2015-06-01

Several fuel and material irradiation experiments have been planned for the Idaho National Laboratory Advanced Reactor Technologies Technology Development Office Advanced Gas Reactor Fuel Development and Qualification Program (referred to as the INL ART TDO/AGR fuel program hereafter), which supports the development and qualification of tristructural-isotropic (TRISO) coated particle fuel for use in HTGRs. The goals of these experiments are to provide irradiation performance data to support fuel process development, qualify fuel for normal operating conditions, support development and validation of fuel performance and fission product transport models and codes, and provide irradiated fuel and materials for post irradiation examination and safety testing (INL 05/2015). AGR-3/4 combined the third and fourth in this series of planned experiments to test TRISO coated low enriched uranium (LEU) oxycarbide fuel. This combined experiment was intended to support the refinement of fission product transport models and to assess the effects of sweep gas impurities on fuel performance and fission product transport by irradiating designed-to-fail fuel particles and by measuring subsequent fission metal transport in fuel-compact matrix material and fuel-element graphite. The AGR 3/4 fuel test was successful in irradiating the fuel compacts to the burnup and fast fluence target ranges, considering the experiment was terminated short of its initial 400 EFPD target (Collin 2015). Out of the 48 AGR-3/4 compacts, 42 achieved the specified burnup of at least 6% fissions per initial heavy-metal atom (FIMA). Three capsules had a maximum fuel compact average burnup < 10% FIMA, one more than originally specified, and the maximum fuel compact average burnup was <19% FIMA for the remaining capsules, as specified. Fast neutron fluence fell in the expected range of 1.0 to 5.5×1025 n/m2 (E >0.18 MeV) for all compacts. In addition, the AGR-3/4 experiment was globally successful in keeping the

Technical basis for the ITER final design report, cost review and safety analysis (FDR)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-12-01

The ITER final design report, cost review and safety analysis (FDR) is the 4th major milestone, representing the progress made in the ITER Engineering Design Activities. With the approval of the Detailed Design Report (DDR), the design work was concentrated on the requirements of operation, with only relatively minor changes to design concepts of major components. The FDR is the culmination of almost 6 years collaborative design and supporting technical work by the ITER Joint Central Team and Home Teams under the terms of the ITER EDA Agreement. Refs, figs, tabs

Technical basis for the ITER final design report, cost review and safety analysis (FDR)

International Nuclear Information System (INIS)

1998-01-01

The ITER final design report, cost review and safety analysis (FDR) is the 4th major milestone, representing the progress made in the ITER Engineering Design Activities. With the approval of the Detailed Design Report (DDR), the design work was concentrated on the requirements of operation, with only relatively minor changes to design concepts of major components. The FDR is the culmination of almost 6 years collaborative design and supporting technical work by the ITER Joint Central Team and Home Teams under the terms of the ITER EDA Agreement

Technical review of externalities issues. Final report

International Nuclear Information System (INIS)

Niemeyer, V.

1994-12-01

Externalities has become the catchword for a major experiment in electric utility regulation. Together with increased competition as a means for economic regulation, this experiment represents a potential revolution in how electric utilities are regulated. It is very important for utilities and policy makers to understand the technical issues and arguments driving the externality experiment. This Technical Review presents four papers covering topics in economics that may play important roles in this revolution. The four papers are: Economic Issues in the Application of Externalities to Electricity Resource Selection; Climate Change, the Marginal Cost of Carbon Dioxide Emissions and the Implications for Carbon Dioxide Emissions Adders; Positive Externalities and Benefits from Electricity; and Socioeconomic Effects of Externality Adders for Electric Utility Emissions

Pre-feasibility study of electron beam irradiation of fresh water

International Nuclear Information System (INIS)

Finshi V, Silvia.

1997-01-01

A technical/economic evaluation of electron beam irradiation for the decontamination of liquids in the country is presented. Irradiation of fresh water is evaluated for the production of drinking water as a replacement for chlorine disinfection, which can lead to the formation of tri halo methanes. that are carcinogenic compounds. The technical literature states that the percentage of microorganisms removed by electro beam irradiation is high and similar to that found with chlorine disinfection. From an economic point of view, irradiation technology is not presently competitive as an alternative to conventional chlorination in terms of processing costs (US$0.23/m 3 ) instead of US$0.013/m 3 for conventional chlorination. Nevertheless, irradiation costs decreased sharply when unit costs for the accelerator machine are decreased with a resulting drop in capital costs

Materials irradiation research in neutron science

Energy Technology Data Exchange (ETDEWEB)

Noda, Kenji; Oyama, Yukio [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1997-11-01

Materials irradiation researches are planned in Neutron Science Research Program. A materials irradiation facility has been conceived as one of facilities in the concept of Neutron Science Research Center at JAERI. The neutron irradiation field of the facility is characterized by high flux of spallation neutrons with very wide energy range up to several hundred MeV, good accessibility to the irradiation field, good controllability of irradiation conditions, etc. Extensive use of such a materials irradiation facility is expected for fundamental materials irradiation researches and R and D of nuclear energy systems such as accelerator-driven incineration plant for long-lifetime nuclear waste. In this paper, outline concept of the materials irradiation facility, characteristics of the irradiation field, preliminary technical evaluation of target to generate spallation neutrons, and materials researches expected for Neutron Science Research program are described. (author)

Intense neutron irradiation facility for fusion reactor materials

Energy Technology Data Exchange (ETDEWEB)

Noda, Kenji; Oyama, Yukio; Kato, Yoshio; Sugimoto, Masayoshi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1997-03-01

Technical R and D of d-Li stripping type neutron irradiation facilities for development of fusion reactor materials was carried out in Fusion Materials Irradiation Test Facility (FMIT) project and Energy Selective Neutron Irradiation Test Facility (ESNIT) program. Conceptual design activity (CDA) of International Fusion Materials Irradiation Facility (IFMIF), of which concept is an advanced version of FMIT and ESNIT concepts, are being performed. Progress of users` requirements and characteristics of irradiation fields in such neutron irradiation facilities, and outline of baseline conceptual design of IFMIF were described. (author)

Technical study gas storage. Final report

International Nuclear Information System (INIS)

Borowka, J.; Moeller, A.; Zander, W.; Koischwitz, M.A.

2001-01-01

This study will answer the following questions: (a) For what uses was the storage facility designed and for what use is it currently applied? Provide an overview of the technical data per gas storage facility: for instance, what is its capacity, volume, start-up time, etc.; (b) How often has this facility been used during the past 10 years? With what purpose was the facility brought into operation at the time? How much gas was supplied at the time from the storage facility?; (c) Given the characteristics and the use of the storage facility during the past 10 years and projected gas consumption in the future, how will the storage facility be used in the future?; (d) Are there other uses for which the gas storage facility can be deployed, or can a single facility be deployed for numerous uses? What are the technical possibilities in such cases? Questions (a) and (b) are answered separately for every storage facility. Questions (c) and (d) in a single chapter each (Chapter 2 and 3). An overview of the relevant storage data relating to current use, use in the last 10 years and use in future is given in the Annex

Food irradiation process control and acceptance. Regional UNDP project for Asia and the Pacific, mission undertaken in Vietnam. Food irradiation programme planning facility operation and pilot scale studies RPFI-Phase 3

International Nuclear Information System (INIS)

Giddings, G.G.

1992-01-01

At the request of the Government of Vietnam, the FAO/IAEA expert undertook a one-week mission to Vietnam between 16 and 23 March 1991, to the Hanoi Irradiation Center of the Vietnam Atomic Energy Commission. This mission included the following: The expert inspected the new Soviet automated, dry storage pilot plant gamma irradiator in the final stages of construction on the outskirts of Hanoi, and met with senior staff of the Hanoi Irradiation Center plus the Center specialized groups to hear and take note of their progress, problems and materials and manpower training expectations, etc. A tour of a large rice and vegetable growing cooperative outside Hanoi was made, followed by a meeting with members of the Cooperative's governing body. This cooperative will participate in pilot scale food irradiation feasibility studies once the new irradiator is operational. The expert provided a technical seminar to the Hanoi Irradiation Center staff, plus a general seminar to members of the Consumers Union of Vietnam plus invited guests, on radiation processing in general and food irradiation in particular, during the week. The expert accompanied Irradiation Center staff to Haiphong to visit the National Institute for Marine Products Research plus two Government-run fishery products processing plants in connection with the marine products side of the national food irradiation programme. He was accompanied to a meeting at the Ministry of Agriculture and Food Industry to meet with the Vice-Minister and staff plus food and allied industry representatives. (author)

Argentina technical report

International Nuclear Information System (INIS)

2002-01-01

At present, the Production Cyclotron Facility, installed at the Ezeiza Atomic Centre, is used for Tl-201 production; F-18 and I-123 production will be incorporated during this year. Concerning I-123 production, a system for irradiation of gaseous target has been developed in the frame of the IAEA Technical Assistance Project (ARG4085). The iodine production system delivers an ultra pure radioisotope via nuclear reactions: 124 Xe (p,2n) 123 Cs → 123 Xe → 123 I and 124 Xe (p,pn) 123 Xe → 123 I. This report describes the target and irradiation chamber design, the radiochemical purification process

Effect of gamma irradiation on drugs

International Nuclear Information System (INIS)

Crucq, A.S.; Deridder, V.; Engalytcheff, A.; Slegers, C.; Tilquin, P.

2005-01-01

Several drugs (ceftazidime, vancomycin, glucagon, erythromycin and dobutamine) were studied in order to determine their radiostability. The methods used to measure the degradation of the drug were the potency and the colour change after irradiation. Electron spin resonance (ESR) is currently being used to detect irradiated foodstuffs and may be a promising technique to detect irradiated drugs. Trapped radicals in cefazolin sodium were studied and quantified by ESR for this purpose. It is proposed that the trapped radicals play an important role in the formation of the final radiolytic compounds. The potency of ceftazidime was not significantly modified after an irradiation of 25 kGy, whereas the potency of erythromycin and dobutamine decreased slightly. Glucagon was revealed to be radiosensitive with a significant decrease in its potency after irradiation. The visible spectra of glucagon and dobutamine did not change significantly after irradiation. The absorbance of erythromycin and vancomycin increased after irradiation. According to European Pharmacopoeia standards, the colour change of ceftazidime is unacceptable. The ESR spectra reveal that the trapped radicals in cefazolin sodium are characteristic of an irradiation. The radical concentration is dependent on the irradiation dose and decays over time. Radical concentration in cefazolin sodium was reduced by 99% after 100 days of storage. These radicals are responsible for about 13% of the measured final radiolytic product. Ionic reactions could also lead to final radiolytic products. (author)

Alaskan Commodities Irradiation Project

International Nuclear Information System (INIS)

Zarling, J.P.; Swanson, R.B.; Logan, R.R.

1988-01-01

The ninety-ninth US Congress commissioned a six-state food irradiation research and development program to evaluate the commercial potential of this technology. Hawaii, Washington, Iowa, Oklahoma and Florida as well as Alaska have participated in the national program; various food products including fishery products, red meats, tropical and citrus fruits and vegetables have been studied. The purpose of the Alaskan study was to review and evaluate those factors related to the technical and economic feasibility of an irradiator in Alaska. This options analysis study will serve as a basis for determining the state's further involvement in the development of food irradiation technology. 40 refs., 50 figs., 53 tabs

78 FR 29239 - Final Priority; Technical Assistance To Improve State Data Capacity-National Technical Assistance...

Science.gov (United States)

2013-05-20

... Assistance To Improve State Data Capacity--National Technical Assistance Center To Improve State Capacity To... Education and Rehabilitative Services announces a priority under the Technical Assistance to Improve State... (FY) 2013 and later years. We take this action to focus attention on an identified national need to...

Final Technical Report: Increasing Prediction Accuracy.

Energy Technology Data Exchange (ETDEWEB)

King, Bruce Hardison [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Hansen, Clifford [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Stein, Joshua [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2015-12-01

PV performance models are used to quantify the value of PV plants in a given location. They combine the performance characteristics of the system, the measured or predicted irradiance and weather at a site, and the system configuration and design into a prediction of the amount of energy that will be produced by a PV system. These predictions must be as accurate as possible in order for finance charges to be minimized. Higher accuracy equals lower project risk. The Increasing Prediction Accuracy project at Sandia focuses on quantifying and reducing uncertainties in PV system performance models.

Final waste classification and waste form technical position papers

International Nuclear Information System (INIS)

1983-05-01

The waste classification technical position paper describes overall procedures acceptable to NRC staff which may be used by licensees to determine the presence and concentrations of the radionuclides listed in section 61.55, and thereby classifying waste for near-surface disposal. This technical position paper also provides guidance on the types of information which should be included in shipment manifests accompanying waste shipments to near-surface disposal facilities. The technical position paper on waste form provides guidance to waste generators on test methods and results acceptable to NRC staff for implementing the 10 CFR Part 61 waste form requirements. It can be used as an acceptable approach for demonstrating compliance with the 10 CFR Part 61 waste structural stability criteria. This technical position paper includes guidance on processing waste into an acceptable stable form, designing acceptable high-integrity containers, packaging cartridge filters, and minimizing radiation effects on organic ion-exchange resins. The guidance in the waste form technical position paper may be used by licensees as the basis for qualifying process control programs to meet the waste form stability requirements, including tests which can be used to demonstrate resistance to degradation arising from the effects of compression, moisture, microbial activity, radiation, and chemical changes. Generic test data (e.g., topical reports prepared by vendors who market solidification technology) may be used for process control program qualification where such generic data is applicable to the particular types of waste generated by a licensee

Food Irradiation Newsletter. Vol. 15, no. 1

International Nuclear Information System (INIS)

1991-05-01

This Newsletter contains reports of the Final FAO/IAEA Research Coordination Meeting (RCM) on the Latin American Regional Cooperative Programme on Food Irradiation, the first FAO/IAEA RCM of the Research Coordination Programme on Analytical Detection Methods for Irradiation Treatment of Foods, and the final FAO/IAEA RCM on the Use of Irradiation as a Quarantine Treatment of Food and Agriculture Commodities. Also included are excerpts of the Seventh Annual Meeting of the International Consultative Group on Food Irradiation (ICGFI) and a summary of an ICGFI Task Force Meeting on Irradiation as a Quarantine Treatment of Fresh Fruits and Vegetables. The new regulations on food irradiation in the United Kingdom, effective 1 January 1991, are summarized

Economic viability and commercial experience with shihoro potato irradiation

International Nuclear Information System (INIS)

Kume, T.

1985-01-01

A commercial potato irradiation plant was established in 1973 at Shihoro in Hokkaido, Japan, with a capacity of about 10,000 tons per month using large baskets containing 1.5 tons of potatoes. For twelve seasons potatoes have been irradiated and marketed by the plant. The paper will discuss the experience with the Shihoro potato irradiator from the technical and economic viewpoints. From the technical viewpoint, the following are the main factors that have contributed to the success of potato irradiation. First, the Japanese government initiated research on food irradiation as a national project and provided financial support. Second, the presence of the Shihoro Agricultural Cooperative Association which handles a large amount of potatoes; and third, the mock-up test for the conceptual design of irradiation was conducted using large baskets for storage and transportation. The cost of the irradiation plant was about 389 million yen, of which 253 million yen was provided by the government. The irradiation plant processes about 15,000 tons of potatoes a year and the costs are 2,000 to 4,500 yen per ton. This accounts for 2 to 3% of the potato price and is within the range of commercial feasibility. The irradiated potatoes effectively controlled the market price and is within the range of commercial feasibility. The irradiated potatoes effectively controlled the market price fluctuations during the off-season

Food irradiation

International Nuclear Information System (INIS)

Matsuyama, Akira

1990-01-01

This paper reviews researches, commentaries, and conference and public records of food irradiation, published mainly during the period 1987-1989, focusing on the current conditions of food irradiation that may pose not only scientific or technologic problems but also political issues or consumerism. Approximately 50 kinds of food, although not enough to fill economic benefit, are now permitted for food irradiation in the world. Consumerism is pointed out as the major factor that precludes the feasibility of food irradiation in the world. In the United States, irradiation is feasible only for spices. Food irradiation has already been feasible in France, Hollands, Belgium, and the Soviet Union; has under consideration in the Great Britain, and has been rejected in the West Germany. Although the feasibility of food irradiation is projected to increase gradually in the future, commercial success or failure depends on the final selection of consumers. In this respect, the role of education and public information are stressed. Meat radicidation and recent progress in the method for detecting irradiated food are referred to. (N.K.) 128 refs

Decommissioning of an Irradiator MPX-γ - 25M and a neutron Irradiator

International Nuclear Information System (INIS)

Soguero, Dania; Guerra, Mercedes; Prieto, Enrique; Desdin, Luis

2013-01-01

In this paper a technology is developed with its procedures in radiation protection to ensure the safety of the process of decommissioning of two irradiators. Both processes are described, the process of decommissioning of a neutron Irradiator 4. 44·10 11 Bq, employed in the vegetal radio mutagenesis, and disassembling of an installation of gamma irradiation of 3.33 * 10 12 Bq, self-shielded of category I, model MPX - γ - 25 M. The specific objectives are: a) identify aspects of the contractual assurance, of human and technical resources, b) to evaluate the radiological situation of the process and c) analyze the potential radiological extraordinary events in each of the steps of the process, ensuring the right answers. Evaluation of radiological successful events described can be considered as reference to address the process of disassembling of other similar irradiators

Position paper on irradiated fuel and waste management. The Achille's heel of the nuclear industry?

Energy Technology Data Exchange (ETDEWEB)

Bonin, Bernard [European Nuclear Society (ENS), Brussel (Belgium). ENS High Scientific Council

2014-07-15

The management and final disposal of irradiated fuel and nuclear waste is often presented by the media and perceived by the public as being an unsolved problem that restricts the future of nuclear energy. However, the nuclear industry focused on this problem very early on and has developed proven technical solutions. Nuclear energy will continue developing worldwide, in spite of the Fukushima accident. Even in those European countries that have decided to phase-out nuclear energy there is a legacy of nuclear waste that must be dealt with. The scientific and technical expertise needed for waste management already exists. Management decisions must be taken. Now is the time for political courage. (orig.)

Food irradiation

International Nuclear Information System (INIS)

Paganini, M.C.

1991-06-01

Food treatment by means of ionizing energy, or irradiation, is an innovative method for its preservation. In order to treat important volumes of food, it is necessary to have industrial irradiation installations. The effect of radiations on food is analyzed in the present special work and a calculus scheme for an Irradiation Plant is proposed, discussing different aspects related to its project and design: ionizing radiation sources, adequate civil work, security and auxiliary systems to the installations, dosimetric methods and financing evaluation methods of the project. Finally, the conceptual design and calculus of an irradiation industrial plant of tubercles is made, based on the actual needs of a specific agricultural zone of our country. (Author) [es

Alumina reinforced tetragonal zirconia (TZP) composites. Final technical report, July 1, 1993--December 31, 1996

International Nuclear Information System (INIS)

Shetty, D.K.

1997-01-01

This final technical report summarizes the significant research results obtained during the period July 1, 1993 through December 31, 1996 in the DOE-supported research project entitled, open-quotes Alumina Reinforced Tetragonal Zirconia (TZP) Compositesclose quotes. The objective of the research was to develop high-strength and high-toughness ceramic composites by combining mechanisms of platelet, whisker or fiber reinforcement with transformation toughening. The approach used included reinforcement of Celia- or yttria-partially-stabilized zirconia (Ce-TZP or Y-TZP) with particulates, platelets, or continuous filaments of alumina

Gas Test Loop Functional and Technical Requirements

International Nuclear Information System (INIS)

Glen R. Longhurst; Soli T. Khericha; James L. Jones

2004-01-01

This document defines the technical and functional requirements for a gas test loop (GTL) to be constructed for the purpose of providing a high intensity fast-flux irradiation environment for developers of advanced concept nuclear reactors. This capability is needed to meet fuels and materials testing requirements of the designers of Generation IV (GEN IV) reactors and other programs within the purview of the Advanced Fuel Cycle Initiative (AFCI). Space nuclear power development programs may also benefit by the services the GTL will offer. The overall GTL technical objective is to provide developers with the means for investigating and qualifying fuels and materials needed for advanced reactor concepts. The testing environment includes a fast-flux neutron spectrum of sufficient intensity to perform accelerated irradiation testing. Appropriate irradiation temperature, gaseous environment, test volume, diagnostics, and access and handling features are also needed. This document serves to identify those requirements as well as generic requirements applicable to any system of this kind

Gas Test Loop Functional and Technical Requirements

Energy Technology Data Exchange (ETDEWEB)

Glen R. Longhurst; Soli T. Khericha; James L. Jones

2004-09-01

This document defines the technical and functional requirements for a gas test loop (GTL) to be constructed for the purpose of providing a high intensity fast-flux irradiation environment for developers of advanced concept nuclear reactors. This capability is needed to meet fuels and materials testing requirements of the designers of Generation IV (GEN IV) reactors and other programs within the purview of the Advanced Fuel Cycle Initiative (AFCI). Space nuclear power development programs may also benefit by the services the GTL will offer. The overall GTL technical objective is to provide developers with the means for investigating and qualifying fuels and materials needed for advanced reactor concepts. The testing environment includes a fast-flux neutron spectrum of sufficient intensity to perform accelerated irradiation testing. Appropriate irradiation temperature, gaseous environment, test volume, diagnostics, and access and handling features are also needed. This document serves to identify those requirements as well as generic requirements applicable to any system of this kind.

Health protection and food preservation by gamma irradiation. Final report, may 1976

International Nuclear Information System (INIS)

1976-05-01

Results of several major studies on food systems for space missions beginning with Apollo 12 through Apollo-Soyuz and investigations of the application of irradiation to food for manned space flight are reported. The study of flight food systems involved the application of radurization (pasteurizing levels) doses of gamma irradiation to flour and bread supplied by Pepperidge Farms in advance of the missions. All flights from Apollo 12 through 17 carried irradiated fresh bread. On Apollo 17, cooperation with Natick Laboratories permitted the introduction of a ham sandwich using irradiated bread and irradiated sterile ham. Investigations centered on irradiated bread were conducted during the course of these missions. Studies were applied to the concept of improving fresh bread from the point of view of mold inhibition. The studies considered how irradiation could best be applied at what levels and on a variety of bread types. Throughout the studies of the application of gamma irradiation the emphasis was placed upon using low levels of irradiation in the pasteurizing or radurizing doses--under a Megarad. The primary goal was to determine if a public health benefit could be demonstrated using radurization along with food preservation and food quality improvements. The public health benefit would be parallel to that of pasteurization of milk as a concept. Publications are included providing the details of these observations, one dealing with the flour characteristics and the other dealing with the influence on fresh bread types. These demonstrate the major findings noted during the period of the studies examining bread. (Author)

Canadian Irradiation Centre

International Nuclear Information System (INIS)

1987-05-01

The Canadian Irradiation Centre is a non-profit cooperative project between Atomic Energy of Canada Limited, Radiochemical Company and Universite du Quebec, Institut Armand-Frappier, Centre for Applied Research in Food Science. The Centre's objectives are to develop, demonstrate and promote Canada's radiation processing technology and its applications by conducting applied research; training technical, professional and scientific personnel; educating industry and government; demonstrating operational and scientific procedures; developing processing procedures and standards, and performing product and market acceptance trials. This pamphlet outlines the history of radoation technology and the services offered by the Canadian Irradiation Centre

IAEA and food irradiation

International Nuclear Information System (INIS)

Machi, Sueo

1995-01-01

IAEA was founded in 1957. 122 countries take part in it. It is operated with the yearly ordinary budget of about 20 billion yen and the technical cooperation budget of about 6 billion yen and by 2200 personnel. Its two important roles are the promotion of the peaceful utilization of atomic energy and the prevention of nuclear proliferation. The activities of IAEA are shown. The cooperation with developing countries and the international research cooperation program are the important activities. The securing of foods is an urgent subject, and the utilization of radiation and isotopes has been promoted, aiming at sustaining agriculture. The necessity of food irradiation is explained, and at present, commercial food irradiation is carried out in 28 countries including Japan. The irradiation less than 10 kGy does not cause poisonous effect in any food, according to JECFI. The new international agreement is expected to be useful for promoting the international trade of irradiated foods. The international cooperation for the spread of food irradiation and the public acceptance of food irradiation are reported. (K.I.)

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Velasco, Mayda [Northwestern University

2013-11-01

This work is focused on the design and construction of novel beam diagnostic and instrumentation for charged particle accelerators required for the next generation of linear colliders. Our main interest is in non-invasive techniques. The Northwestern group of Velasco has been a member of the CLIC Test Facility 3 (CTF3) collaboration since 2003, and the beam instrumentation work is developed mostly at this facility1. This 4 kW electron beam facility has a 25-170 MeV electron LINAC. CTF3 performed a set of dedicated measurements to finalize the development of our RF-Pickup bunch length detectors. The RF-pickup based on mixers was fully commissioned in 2009 and the RF-pickup based on diodes was finished in time for the 2010-11 data taking. The analysis of all the data taken in by the summer of 2010 was finish in time and presented at the main conference of the year, LINAC 2010 in Japan.

Food irradiation: its role in food safety

International Nuclear Information System (INIS)

Qureshi, R. U.

1985-01-01

There are food safety criteria generally defined by international groups and specifically defined by individual countries. Food irradiation will be discussed in the light of food safety regulations. The merits and acceptability of food irradiation in promoting trade within and between countries will also be discussed. The need for public awareness and training of technical personnel will be highlighted

Food irradiation: its role in food safety

Energy Technology Data Exchange (ETDEWEB)

Qureshi, R U

1986-12-31

There are food safety criteria generally defined by international groups and specifically defined by individual countries. Food irradiation will be discussed in the light of food safety regulations. The merits and acceptability of food irradiation in promoting trade within and between countries will also be discussed. The need for public awareness and training of technical personnel will be highlighted

Technical aspects of flue gas irradiation

International Nuclear Information System (INIS)

Cleland, M.R.; Galloway, R.A.; Stichelbaut, F.; Abs, M.

2011-01-01

Removal of SO 2 and NO x from flue gases in fossil-fueled power plants by irradiation with accelerated electrons was first investigated in Japan more than 30 years ago. This process has since been extensively evaluated in several pilot facilities in Japan, the USA, Germany, Poland, Bulgaria and China. Recently, it has advanced to the demonstration plant stage in Poland, Japan and China. Except for the initial research facility in Japan, which had a 5.5 MeV microwave linear accelerator, these facilities have used relatively low-energy dc accelerators rated from 0.3 MeV to 0.8 MeV. An attractive feature of such accelerators is their high electrical efficiency, which can exceed 90%. However, the electron beam power dissipated in the two titanium beam windows, the first on the accelerator and the second on the flue gas duct, and in the air space between the windows must also be taken into account. These beam power losses have been calculated as 54% at 0.50 MeV and 28% at 0.75 MeV, but they decrease further to 17% at 1.0 MeV, 9.3% at 1.5 MeV, 6.7% at 2.0 MeV, 5.2% at 2.5 MeV and 4.6% at 3.0 MeV. The use of accelerators providing electron energies higher than 0.75 MeV could facilitate the generation and delivery of the high beam current and beam power requirements for large electric power plants, which are about 1% to 2% of the electrical power output of the plant. Most of the pilot and demonstration facilities have used ammonia gas to neutralize the acid vapors produced during the irradiation process. The resulting by-products are ammonium sulfate and ammonium nitrate, which have value as agricultural fertilizers. On the other hand, two pilot facilities, one in the USA and the other in Japan, have shown that slaked lime (calcium hydroxide) is a possible alternative to ammonia. The resulting by-products in this case are calcium sulfate and calcium nitrate, which can be used as soil amendments or to make gypsum board (drywall) for interior construction in homes and

Technical aspects of flue gas irradiation

Energy Technology Data Exchange (ETDEWEB)

Cleland, M. R.; Galloway, R. A. [IBA Industrial, Inc., Edgewood, NY (United States); Stichelbaut, F.; Abs, M. [IBA Industrial, Inc., Louvain-la-Neuve (Belgium)

2011-07-01

Removal of SO{sub 2} and NO{sub x} from flue gases in fossil-fueled power plants by irradiation with accelerated electrons was first investigated in Japan more than 30 years ago. This process has since been extensively evaluated in several pilot facilities in Japan, the USA, Germany, Poland, Bulgaria and China. Recently, it has advanced to the demonstration plant stage in Poland, Japan and China. Except for the initial research facility in Japan, which had a 5.5 MeV microwave linear accelerator, these facilities have used relatively low-energy dc accelerators rated from 0.3 MeV to 0.8 MeV. An attractive feature of such accelerators is their high electrical efficiency, which can exceed 90%. However, the electron beam power dissipated in the two titanium beam windows, the first on the accelerator and the second on the flue gas duct, and in the air space between the windows must also be taken into account. These beam power losses have been calculated as 54% at 0.50 MeV and 28% at 0.75 MeV, but they decrease further to 17% at 1.0 MeV, 9.3% at 1.5 MeV, 6.7% at 2.0 MeV, 5.2% at 2.5 MeV and 4.6% at 3.0 MeV. The use of accelerators providing electron energies higher than 0.75 MeV could facilitate the generation and delivery of the high beam current and beam power requirements for large electric power plants, which are about 1% to 2% of the electrical power output of the plant. Most of the pilot and demonstration facilities have used ammonia gas to neutralize the acid vapors produced during the irradiation process. The resulting by-products are ammonium sulfate and ammonium nitrate, which have value as agricultural fertilizers. On the other hand, two pilot facilities, one in the USA and the other in Japan, have shown that slaked lime (calcium hydroxide) is a possible alternative to ammonia. The resulting by-products in this case are calcium sulfate and calcium nitrate, which can be used as soil amendments or to make gypsum board (drywall) for interior construction in homes

Foodstuff irradiation

International Nuclear Information System (INIS)

1982-01-01

Report written on behalf of the Danish Food Institute summarizes national and international rules and developments within food irradiation technology, chemical changes in irradiated foodstuffs, microbiological and health-related aspects of irradiation and finally technological prospects of this conservation form. Food irradiatin has not been hitherto applied in Denmark. Radiation sources and secondary radiation doses in processed food are characterized. Chemical changes due to irradiation are compared to those due to p.ex. food heating. Toxicological and microbiological tests and their results give no unequivocal answer to the problem whether a foodstuff has been irradiated. The most likely application fields in Denmark are for low radiation dosis inhibition of germination, riping delay and insecticide. Medium dosis (1-10 kGy) can reduce bacteria number while high dosis (10-50 kGy) will enable total elimination of microorganisms and viruses. Food irradiation can be acceptable as technological possibility with reservation, that further studies follow. (EG)

Packing for food irradiation

Energy Technology Data Exchange (ETDEWEB)

Chmielewski, A G [Institute of Nuclear Chemistry and Technology, Warsaw (Poland)

2006-07-01

Joint FAO/IAEA/WHO Expert Committee approved the use of radiation treatment of foods. Nowadays food packaging are mostly made of plastics, natural or synthetic, therefore effect of irradiation on these materials is crucial for packing engineering for food irradiation technology. By selecting the right polymer materials for food packaging it can be ensured that the critical elements of material and product performance are not compromised. When packaging materials are in contact with food at the time of irradiation that regulatory approvals sometimes apply. The review of the R-and-D and technical papers regarding material selection, testing and approval is presented in the report. The most information come from the USA where this subject is well elaborated, the International Atomic Energy Agency (IAEA) reports are reviewed as well. The report can be useful for scientists and food irradiation plants operators. (author)

Packing for food irradiation

International Nuclear Information System (INIS)

Chmielewski, A.G.

2006-01-01

Joint FAO/IAEA/WHO Expert Committee approved the use of radiation treatment of foods. Nowadays food packaging are mostly made of plastics, natural or synthetic, therefore effect of irradiation on these materials is crucial for packing engineering for food irradiation technology. By selecting the right polymer materials for food packaging it can be ensured that the critical elements of material and product performance are not compromised. When packaging materials are in contact with food at the time of irradiation that regulatory approvals sometimes apply. The review of the R-and-D and technical papers regarding material selection, testing and approval is presented in the report. The most information come from the USA where this subject is well elaborated, the International Atomic Energy Agency (IAEA) reports are reviewed as well. The report can be useful for scientists and food irradiation plants operators. (author)

State child health; revisions to the regulations implementing the State Children's Health Insurance Program. Interim final rule with comment period; revisions, delay of effective date, and technical amendments to final rule.

Science.gov (United States)

2001-06-25

Title XXI authorizes the State Children's Health Insurance Program (SCHIP) to assist State efforts to initiate and expand the provision of child health assistance to uninsured, low-income children. On January 11, 2001 we published a final rule in the Federal Register to implement SCHIP that has not gone into effect. This interim final rule further delays the effective date, revises certain provisions and solicits public comment, and makes technical corrections and clarifications to the January 2001 final rule based on further review of the comments received and applicable law. Only the provisions set forth in this document have changed. All other provisions set forth in the January 2001 final rule will be implemented without change.

Repair welding of fusion reactor components. Final technical report

International Nuclear Information System (INIS)

Chin, B.A.; Wang, C.A.

1997-01-01

The exposure of metallic materials, such as structural components of the first wall and blanket of a fusion reactor, to neutron irradiation will induce changes in both the material composition and microstructure. Along with these changes can come a corresponding deterioration in mechanical properties resulting in premature failure. It is, therefore, essential to expect that the repair and replacement of the degraded components will be necessary. Such repairs may require the joining of irradiated materials through the use of fusion welding processes. The present ITER (International Thermonuclear Experimental Reactor) conceptual design is anticipated to have about 5 km of longitudinal welds and ten thousand pipe butt welds in the blanket structure. A recent study by Buende et al. predict that a failure is most likely to occur in a weld. The study is based on data from other large structures, particularly nuclear reactors. The data used also appear to be consistent with the operating experience of the Fast Flux Test Facility (FFTF). This reactor has a fuel pin area comparable with the area of the ITER first wall and has experienced one unanticipated fuel pin failure after two years of operation. The repair of irradiated structures using fusion welding will be difficult due to the entrapped helium. Due to its extremely low solubility in metals, helium will diffuse and agglomerate to form helium bubbles after being trapped at point defects, dislocations, and grain boundaries. Welding of neutron-irradiated type 304 stainless steels has been reported with varying degree of heat-affected zone cracking (HAZ). The objectives of this study were to determine the threshold helium concentrations required to cause HAZ cracking and to investigate techniques that might be used to eliminate the HAZ cracking in welding of helium-containing materials

Final priority. Rehabilitation Training: Job-Driven Vocational Rehabilitation Technical Assistance Center. Final priority.

Science.gov (United States)

2014-08-19

The Assistant Secretary for Special Education and Rehabilitative Services announces a priority under the Rehabilitation Training program to establish a Job-Driven Vocational Rehabilitation Technical Assistance Center (JDVRTAC). The Assistant Secretary may use this priority for competitions in fiscal year (FY) 2014 and later years. We take this action to focus on training in an area of national need. Specifically, this priority responds to the Presidential Memorandum to Federal agencies directing them to take action to address job-driven training for the Nation's workers. The JDVRTAC will provide technical assistance (TA) to State vocational rehabilitation (VR) agencies to help them develop for individuals with disabilities training and employment opportunities that meet the needs of today's employers.

Irradiation as a quarantine treatment of arthropod pests. Proceedings of a final research co-ordination meeting

International Nuclear Information System (INIS)

1999-05-01

Fresh horticultural produce from tropical and sub-tropical areas often harbours insects and mites and are quarantined by importing countries. Such commodities cannot gain access to countries which have strict quarantine regulations such as Australia, Japan, New Zealand and the United States of America unless treated by an approved method/procedure to eliminate such pests. Current approved methods include fumigation by methyl bromide, hot water dip, vapour heat, dried heat and irradiation. Methyl bromide is being phased out globally under the Montreal Protocol in view of its strong ozone depleting properties. Countries such as the USA and those of the European Union are required to phase out the production of this chemical by the year 2005. Among other phytosanitary treatments, irradiation appears to have an edge as it is more versatile in controlling various pests and causes insignificant changes in quality of the treated products. The CRP on Irradiation as a Quarantine Treatment of Mites, Nematodes and Insects other than Fruit Flies, in operation between 1992 and 1997, attempted to fill the gap of information on the effectiveness of irradiation against other quarantine pests. Significant data were generated by this CRP to demonstrate that a minimum dose of between 200 and 400 Gy would render a number of non-fruit fly insects and mites sterile, thus meeting quarantine requirements. However, only a limited species of insects and mites were studied. Additional data are required to provide conclusive evidence that such a dose would render most, if not all, species of non-fruit fly insects and mites sterile. Plant parasitic nematodes appear to be resistant to irradiation as the dose required to render them sterile would cause damage to fresh horticultural commodities. Irradiation would be a useful quarantine treatment against this pest only for durable commodities such as pot soil, wood products, etc. This publication presents the research results of the CRP presented

Irradiation as a quarantine treatment of arthropod pests. Proceedings of a final research co-ordination meeting

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

Fresh horticultural produce from tropical and sub-tropical areas often harbours insects and mites and are quarantined by importing countries. Such commodities cannot gain access to countries which have strict quarantine regulations such as Australia, Japan, New Zealand and the United States of America unless treated by an approved method/procedure to eliminate such pests. Current approved methods include fumigation by methyl bromide, hot water dip, vapour heat, dried heat and irradiation. Methyl bromide is being phased out globally under the Montreal Protocol in view of its strong ozone depleting properties. Countries such as the USA and those of the European Union are required to phase out the production of this chemical by the year 2005. Among other phytosanitary treatments, irradiation appears to have an edge as it is more versatile in controlling various pests and causes insignificant changes in quality of the treated products. The CRP on Irradiation as a Quarantine Treatment of Mites, Nematodes and Insects other than Fruit Flies, in operation between 1992 and 1997, attempted to fill the gap of information on the effectiveness of irradiation against other quarantine pests. Significant data were generated by this CRP to demonstrate that a minimum dose of between 200 and 400 Gy would render a number of non-fruit fly insects and mites sterile, thus meeting quarantine requirements. However, only a limited species of insects and mites were studied. Additional data are required to provide conclusive evidence that such a dose would render most, if not all, species of non-fruit fly insects and mites sterile. Plant parasitic nematodes appear to be resistant to irradiation as the dose required to render them sterile would cause damage to fresh horticultural commodities. Irradiation would be a useful quarantine treatment against this pest only for durable commodities such as pot soil, wood products, etc. This publication presents the research results of the CRP presented

Final priority; Technical Assistance on State Data Collection--IDEA Data Management Center. Final priority.

Science.gov (United States)

2014-08-05

The Assistant Secretary for the Office of Special Education and Rehabilitative Services (OSERS) announces a priority under the Technical Assistance on State Data Collection program. The Assistant Secretary may use this priority for competitions in fiscal year (FY) 2014 and later years. We take this action to fund a cooperative agreement to establish and operate an IDEA Data Management Center (Center) that will provide technical assistance (TA) to improve the capacity of States to meet the data collection requirements of the Individuals with Disabilities Education Act (IDEA).

Radurization of spices by irradiation in Cuba

International Nuclear Information System (INIS)

Alvarez Gil, M.; Rodriguez, M.; Prieto, E.; Pino, J.

1997-01-01

This paper presents the research results that prove the technical feasibility according to the hygiene conditions existing in Cuba for irradiating different spices. The results show both the possibility and and the benefit of using a one irradiation application to these products. One global average doses of 5 KGy was enough for decontaminating black pepper, paprika, cumin, must meg and oregano without affecting either their chemical components or the quality of their taste. Sausages manufactured with irradiated spices did not irradiating spices is much higher that of fumigation, et has many important social and economic advantages

Technology of irradiation of liquids by electron beams

International Nuclear Information System (INIS)

Tofaute, K.

1979-01-01

The methods of pretreatment, the technical details of the irradiating equipment, the applied radiation doses and the general requirements of the effectively working system are described. The extent of reinfection is compared in cases of heat-treated and electron-irradiated mud. The latter method gave significantly better results. (L.E.)

Next Generation Nuclear Plant (NGNP) Prismatic HTGR Conceptual Design Project - Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Saurwein, John

2011-07-15

This report is the Final Technical Report for the Next Generation Nuclear Plant (NGNP) Prismatic HTGR Conceptual Design Project conducted by a team led by General Atomics under DOE Award DE-NE0000245. The primary overall objective of the project was to develop and document a conceptual design for the Steam Cycle Modular Helium Reactor (SC-MHR), which is the reactor concept proposed by General Atomics for the NGNP Demonstration Plant. The report summarizes the project activities over the entire funding period, compares the accomplishments with the goals and objectives of the project, and discusses the benefits of the work. The report provides complete listings of the products developed under the award and the key documents delivered to the DOE.

Next Generation Nuclear Plant (NGNP) Prismatic HTGR Conceptual Design Project - Final Technical Report

International Nuclear Information System (INIS)

Saurwein, J.

2011-01-01

This report is the Final Technical Report for the Next Generation Nuclear Plant (NGNP) Prismatic HTGR Conceptual Design Project conducted by a team led by General Atomics under DOE Award DE-NE0000245. The primary overall objective of the project was to develop and document a conceptual design for the Steam Cycle Modular Helium Reactor (SC-MHR), which is the reactor concept proposed by General Atomics for the NGNP Demonstration Plant. The report summarizes the project activities over the entire funding period, compares the accomplishments with the goals and objectives of the project, and discusses the benefits of the work. The report provides complete listings of the products developed under the award and the key documents delivered to the DOE.

From the Phenix irradiation end to the analytical results: PROFIL R target destructive characterization

International Nuclear Information System (INIS)

Ferlay, G.; Dancausse, J. Ph.

2009-01-01

In the French long-lived radionuclide (LLRN) transmutation program, several irradiation experiments were initiated in the Phenix fast neutron reactor to obtain a better understanding of the transmutation processes. The PROFIL experiments are performed in order to collect accurate information on the total capture integral cross sections of the principal heavy isotopes and some important fission products in the spectral range of fast reactors. One of the final goals is to diminish the uncertainties on the capture cross-section of the fission products involved in reactivity losses in fast reactors. This program includes two parts: PROFIL-R irradiated in a standard fast reactor spectrum and PROFIL-M irradiated in a moderated spectrum. The PROFIL-R and PROFIL-M irradiations were completed in August 2005 and May 2008, respectively. For both irradiations more than a hundred containers with isotopes of pure actinides and other elements in different chemical forms must be characterized. This raises a technical and analytical challenge: how to recover by selective dissolution less than 5 mg of isotope powder from a container with dimensions of only a few millimeters using hot cell facilities, and how to determine analytically both trace and ultra-trace elemental and isotopic compositions with sufficient accuracy to be useful for code calculations. (authors)

Technical evaluation of gamma-irradiation pretreatment on quality preservation for fresh fish

International Nuclear Information System (INIS)

Ke, P.J.; Linke, B.A.; Lemon, D.W.

1985-07-01

A comprehensive review and evaluation on the use of gamma-irradiation for preserving fresh fish quality has been made. The advantages and limitations of using gamma-irradiation of less than 1 M rad have been re-evaluated and compared with previous tests at the Halifax laboratory in terms of physical, organoleptic and some post process quality assessments. Cod, mackerel, and scallop were chosen as the models for lean, fatty and shell fish respectively. The irradiation process can prevent bacterial spoilage in fish, particularly when chilling and/or handling practices are inadequate, but the potential catalytic influences on enzymatic and chemical deterioration during the post-mortem period should also be considered. Some considerations and reservations concerning the changes in overall quality for irradiated fish are discussed. Before more research is completed, the gamma-irradiation process should not be used for shellfish, fatty fish and various prepared and frozen fish products made from Canadian Atlantic species

Imagining Technicities

DEFF Research Database (Denmark)

Liboriussen, Bjarke; Plesner, Ursula

2011-01-01

to the elements of taste and skill. In the final analysis those references were synthesized as five imagined technicities: the architect, the engineer, the client, the Chinese, and the Virtual World native. Because technicities are often assumed and rarely discussed as actants who influence practice, their role......, this article focuses on innovative uses of virtual worlds in architecture. We interviewed architects, industrial designers and other practitioners. Conceptually supported by an understanding of technicity found in Cultural Studies, the interviews were then coded with a focus on interviewees’ references...... in cooperation and development of ICTs seems to pass unnoticed. However, since they are aligned into ICTs, technicities impact innovation....

Irradiation as a phytosanitary treatment of food and agricultural commodities. Proceedings of a final research coordination meeting

International Nuclear Information System (INIS)

2004-11-01

World trade in fresh horticultural produce, durables and ornamentals continues to grow. Accompanying increased trade in agricultural products is the increased risk for inadvertently transporting quarantine pests to countries or regions where they do not occur. Quarantined pests, including insects such as fruit flies, beetles, moths, scales, mealybugs, thrips, and mites, can seriously disrupt marketing of fresh agricultural products not only between countries, but also between geographical areas within countries (e.g. Florida to California; Hawaii to mainland USA; Queensland to Victoria, Australia; Okinawa to Japan) unless accepted postharvest quarantine treatments are available. Quarantine or phytosanitary treatments (such as fumigation, heat, cold or irradiation) disinfest host commodities of insect pests before they are moved through market channels to areas where the pests do not occur. Among the phytosanitary treatments, irradiation is recognized as a versatile treatment with broadspectrum activity against arthropod pests at dose levels that have minimal adverse effects on the quality of most commodities. The Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture, initiated in 1998 a Coordinated Research Project (CRP) on Irradiation as a Phytosanitary Treatment of Food and Agricultural Commodities. This CRP included 16 participants from Australia, Brazil, Chile, China (2), India, Islamic Republic of Iran, Japan, Malaysia, Philippines, Poland, Syrian Arab Republic, Thailand, Turkey and the USA (2). Research coordination meetings were held in Bangkok, Thailand, 29 March - 2 April 1999; Fresno, California, 13-16 November 2001; and Vienna, 2-4 November 2002. This CRP built on the achievements of two previous CRPs on Irradiation as a Quarantine Treatment of Fresh Fruits and Vegetables, (1986-1990), and Irradiation as a Quarantine Treatment of Mites, Nematodes and Insects other than Fruit Flies(1992-1997). This publication presents the research results

The utilization of irradiation techniques in food industry

International Nuclear Information System (INIS)

Szabo, S.A.

1988-01-01

Irradiation technical researches and the main areas of nuclear technical applications are surveyed, and the main areas where nuclear techniques are used are reported. Then an overview on radiation techniques including radiostimulation, radiomutation, radurization, radioecology and isotope techniques used in the food industry is presented. (author) 4 refs

Heavy-section steel irradiation program. Progress report, October 1994--March 1995

International Nuclear Information System (INIS)

Corwin, W.R.

1995-10-01

This document is the October 1994-March 1995 Progress Report for the Heavy Section Steel Irradiation Program. The report contains a summary of activities in each of the 14 tasks of the HSSI Program, including: (1) Program management, (2) Fracture toughness shifts in high-copper weldments, (3) Fracture toughness shifts in low upper-shelf welds, (4) Irradiation effects in a commercial low upper-shelf weld, (5) Irradiation effects on weld heat-affected zone and plate materials, (6) Annealing effects in low upper-shelf welds, (7) Microstructural analysis of radiation effects, (8) In-service irradiated and aged material evaluations, (9) Japanese power development reactor vessel steel examination, (10) fracture toughness curve shift method, (11) Special technical assistance, (12) Technical assistance for JCCCNRS, (13) Correlation monitor materials, and (14) Test reactor irradiation coordination. Selected papers have been indexed separately for inclusion in the Energy Science and Technology Database

Fast-neutron dosimetry in the seed-irradiation facility, ASTRA reactor, Seibersdorf

International Nuclear Information System (INIS)

Ahnstroem, G.; Burtscher, A.; Casta, J.

1967-01-01

An important part of the co-ordinated programme on the neutron irradiation of seeds has been the construction of a fast-neutron irradiation facility for swimming-pool reactors. This facility was installed around 70 cm from the core in the ASTRA reactor swimming-pool at the end of December, 1966. Also, for this programme a pair of constant potential ionization chambers have been constructed at the Institute of Biochemistry, Stockholm University. These chambes are of the type described in the technical annex and are the same size as the seed-irradiation vials to be used in the seed-irradiation container (diam. =15 mm, length = 60 mm). Some preliminary dosimetry experiments were undertaken to test the irradiation facility and the ionization chambers, and to investigate the usefulness of the dosimetry instructions in the Technical Annex. The results of these experiments are discussed in this paper. 3 refs, 6 figs, 7 tabs

Improving measurement quality assurance for photon irradiations at Department of Energy facilities. Final technical report

International Nuclear Information System (INIS)

1996-01-01

For radiation-instrument calibration to be generally acceptable throughout the US, direct or indirect traceability to a primary standard is required. In most instances, one of the primary standards established at NIST is employed for this purpose. The Department of Energy Laboratory Accreditation Program (DOELAP) is an example of a program employing dosimetry based on the NIST primary photon-, beta particle- and neutron-dosimetry standards. The NIST primary dosimetry standards for bremsstrahlung were first established in the 1950s. They have been updated since then on several occasions. In the 1970s, Technical Committee 85 of the International Standards Organization (ISO) started its work on establishing sets of internationally acceptable, well-characterized photon beams for the calibration of radiation-protection instruments. It is the intent of this paper to make a detailed comparison between the current NIST and the most up-to-date ISO techniques. At present, 41 bremsstrahlung techniques are specified in ISO 4037 while NIST supports a total of 32 techniques. Given the existing equivalences, it makes sense to try to extend the NIST techniques to cover more of the ISO Narrow Spectrum and High Air-Kerma Rate Series. These extensions will also allow the possibility for use of ISO beam techniques in future revisions of the DOELAP standard, which has been suggested by DOE. To this end, NIST was funded by DOE to procure material and make adaptations to the existing NIST x-ray calibration ranges to allow NIST to have the capability of producing all the ISO bremsstrahlung techniques. The following sections describe the steps that were taken to achieve this

Present status of ESNIT (energy selective neutron irradiation test facility) program

International Nuclear Information System (INIS)

Noda, K.; Ohno, H.; Sugimoto, M.; Kato, Y.; Matsuo, H.; Watanabe, K.; Kikuchi, T.; Sawai, T.; Usui, T.; Oyama, Y.; Kondo, T.

1994-01-01

The present status of technical studies of a high energy neutron irradiation facility, ESNIT (energy selective neutron irradiation test facility), is summarized. Technological survey and feasibility studies of ESNIT have continued since 1988. The results of technical studies of the accelerator, the target and the experimental systems in ESNIT program were reviewed by an International Advisory Committee in February 1993. Recommendations for future R and D on ESNIT program are also summarized in this paper. ((orig.))

Safety protection and technical improvement of 60Co irradiation facilities

International Nuclear Information System (INIS)

Zhou Yongxing; Liang Cannan

1993-01-01

To ensure personal safety, some improvements has been made in the design of 60 Co irradiation compartment. The shielding door was interlocked while the 60 Co source to be lifted to the irradiation position or lowered to the shielded position. A universal change-over switch was used to cut the power supply when the source moved beyond the limits. Both γ-ray alarm and a closed-TV system were adopted. The electromagnetic attraction method was employed to shift the 60 Co source from the Pb container to the source pipe

Technology management for the installation of a food irradiator in the Ribeira Valley

International Nuclear Information System (INIS)

Ghobril, Carlos Nabil

2008-01-01

This thesis presents a research focused on technology management applied to technical and economic viability study for the installation of a multi propose irradiator in Vale do Ribeira. First, the work presents the regional characteristics that shows Vale do Ribeira as the less economically developed region of Sao Paulo state. On the other side, it shows the emergence of irradiation techniques applied to the food industry, with accepted and recommended results by international authorities. Technology management, from the conceptual basis here presented, links regional environment reality to available technical knowledge, in search of regional development. The methodology was composed by the use of bibliographical, qualitative and quantitative research, and the analysis was supported by the use of statistical techniques and economic viability analysis. The present research concludes that there is technical and economic viability of the venture here analyzed, although it should be recommended more studies about banana irradiation and about Brazilian consumer acceptance to irradiated food products. (author)

Paranasal sinus tumors: Results of irradiation alone vs. irradiation and surgery

International Nuclear Information System (INIS)

Shumway, R.C.; Chung, C.T.; Sagerman, R.H.; King, G.A.; Dalal, P.S.

1987-01-01

Forty patients were treated for carcinoma of the paranasal sinuses from 1965 to 1983. Thirteen patients were treated with an integrated program of surgery plus irradiation; and 27 received irradiation alone. Five-year actuarial survival for patients with maxillary antral tumors was 45% (5 of 11) in the combined treatment group and 21% (3 of 14) in the radiation-only group. Local control for the combined treatment group was 73% (8 of 11), compared to 20% (3 of 15) for the radiation-only group (P > .01). Twenty of 24 patients dying of disease had local recurrence. The technical aspects of treatment and a review of the literature are presented

IAEA International Database on Irradiated Nuclear Graphite Properties. Summary report of consultants' meeting. 12. meeting of the Technical Steering Committee

International Nuclear Information System (INIS)

Chung, H.K.; Wickham, A.J.

2010-02-01

The 12th Meeting of the Technical Steering Committee for the International Database on Irradiated Nuclear Graphite Properties was held on 12-13 November 2009 at the IAEA Headquarters, Vienna, Austria. All discussions, recommendations and actions of this Consultants' Meeting are recorded in this report. The purposes of the meeting were to review the matters and actions identified in the previous meeting, undertake a review of the current status of the database, and make recommendations for action over the next year. This report contains the status of the identified actions as well as a summary of the recommendations on enhancements to the database. (author)

Uncertainty Quantification in the Reliability and Risk Assessment of Generation IV Reactors: Final Scientific/Technical Report

International Nuclear Information System (INIS)

Vierow, Karen; Aldemir, Tunc

2009-01-01

The project entitled, 'Uncertainty Quantification in the Reliability and Risk Assessment of Generation IV Reactors', was conducted as a DOE NERI project collaboration between Texas A and M University and The Ohio State University between March 2006 and June 2009. The overall goal of the proposed project was to develop practical approaches and tools by which dynamic reliability and risk assessment techniques can be used to augment the uncertainty quantification process in probabilistic risk assessment (PRA) methods and PRA applications for Generation IV reactors. This report is the Final Scientific/Technical Report summarizing the project.

Uncertainty Quantification in the Reliability and Risk Assessment of Generation IV Reactors: Final Scientific/Technical Report

Energy Technology Data Exchange (ETDEWEB)

Vierow, Karen; Aldemir, Tunc

2009-09-10

The project entitled, “Uncertainty Quantification in the Reliability and Risk Assessment of Generation IV Reactors”, was conducted as a DOE NERI project collaboration between Texas A&M University and The Ohio State University between March 2006 and June 2009. The overall goal of the proposed project was to develop practical approaches and tools by which dynamic reliability and risk assessment techniques can be used to augment the uncertainty quantification process in probabilistic risk assessment (PRA) methods and PRA applications for Generation IV reactors. This report is the Final Scientific/Technical Report summarizing the project.

Final report on neutron irradiation at low temperature to investigate plastic instability and a high temperature to study cavitation

International Nuclear Information System (INIS)

Singh, B.N.; Eldrup, M.; Golubov, S.I.; Edwards, D.J.; Jung, P.

2005-01-01

Effects of neutron irradiation on defect accumulation and physical and mechanical properties of pure iron and F82H and EUROFER 97 ferritic-martensitic steels have been investigated. Tensile specimens were neutron irradiated to a dose level of 0,23 dpa at 333 and 573 K. Electrical resistivity and tensile properties were measured both in the unirradiated and irradiated condition. Some additional specimens of pure iron were irradiated at 333 K to doses of 10-3, 10-2 and 10-1 dpa and tensile tested at 333 K. To investigate the effect of helium on cavity nucleation and growth, specimens of pure iron and EUROFER 97 were implanted with different amounts of helium at 323 K and subsequently neutron irradiated to doses of 10-3, 10-2 and 10-1 dpa at 323 K. Defect microstructures were investigated using positron annihilation spectroscopy (PAS) and transmission electron microscopy (TEM). Numerical calculations, based on the production bias model (PBM) were carried out to study the details of evolution of cavities with and without helium generation. The phenomena of dislocation decoration and raft formation, which are important for understanding radiation hardening and plastic flow localization, have been studied using the Kinetic Monte Carlo (KMC) code during a realistic dynamic irradiation of bcc iron at 300 K. Molecular dynamics (MD) simulations have been carried out to study the stress dependencies of dislocation velocity and drag coefficient for an edge dislocation decorated with small SIA loops.The present report describes both experimental procedure and calculational methodology employed in the present work. The main results of all these investigations, both experimental and theoretical, are highlighted with appropriate examples. Finally, a brief summary is given of the main results conclusions. (au)

Food Irradiation Newsletter. V. 14, no. 2

International Nuclear Information System (INIS)

1990-12-01

This issue reports specific training activities on Food Irradiation Process Control School, both for technical supervisors of irradiation facilities and food control officials/inspectors, and summary reports of Workshops on dosimetry techniques for food irradiation and on techno-economic feasibility of food irradiation for Latin American countries are included. After 12 years of operation, the International Facility for Food Irradiation Technology (IFFIT) will cease to function after 31 December 1990. This issue reports the last inter-regional training course organized by IFFIT, and also features reports on food irradiation in Asia. Active developments in the field in several Asian countries may be found in the reports of the Workshop on the Commercialization of Food Irradiation, Shanghai, and the Research Co-ordination Meeting on the Asian Regional Co-operative Project on Food Irradiation (with emphasis on acceptance and process control), Bombay. Status reports of programmes in these countries are also included. Refs and tabs

Analysis of irradiation processes for laser-induced periodic surface structures

NARCIS (Netherlands)

Eichstädt, J.; Huis In 't Veld, A.J.

2013-01-01

The influence of errors on the irradiation process for laser-induced periodic surface structures (LIPSS) was studied theoretically with energy density simulations. Therefore an irradiation model has been extended by a selection of technical variations. The influence of errors has been found in a

Food preservation by irradiation

International Nuclear Information System (INIS)

Oztasiran, I.

1984-01-01

Irradiation is a physical process for treating food and as such it is comparable to other processing techniques such as heating or freezing foods for preservation. The energy level used in food irradiation is always below that producing radioactivity in the treated food, hence this aspect can be totally excluded in wholesomeness evaluations. Water is readily ionized and may be the primary source of ionization in foods with secondary effects on other molecules, possibly more a result of water ionization than of direct hits. In the presence of oxygen, highly reactive compounds may be produced, such as H, H 3 0+ and H 2 O 2 . Radiation at the energy flux levels used for food (<2 MeV) does not induce radioactivity. Food irradiation applications are already technically and economically feasible and that food so treated is suitable for consumption. Food irradiation techniques can play an important role for an improved preservation, storage and distribution of food products. (author)

Programs of Study as a State Policy Mandate: A Longitudinal Study of the South Carolina Personal Pathways to Success Initiative. Final Technical Report: Major Findings and Implications

Science.gov (United States)

Hammond, Cathy; Drew, Sam F.; Withington, Cairen; Griffith, Cathy; Swiger, Caroline M.; Mobley, Catherine; Sharp, Julia L.; Stringfield, Samuel C.; Stipanovic, Natalie; Daugherty, Lindsay

2013-01-01

This is the final technical report from the National Research Center for Career and Technical Education's (NRCCTE's) five-year longitudinal study of South Carolina's Personal Pathway to Success initiative, which was authorized by the state's Education and Economic Development Act (EEDA) in 2005. NRCCTE-affiliated researchers at the National…

Standardized methods to verify absorbed dose in irradiated food for insect control. Proceedings of a final research co-ordination meeting

International Nuclear Information System (INIS)

2001-03-01

Irradiation to control insect infestation of food is increasingly accepted and applied, especially as a phytosanitary treatment of food as an alternative to fumigation. However, unlike other processes for insect control, irradiation does not always result in immediate insect death. Thus, it is conceivable that fresh and dried fruits and tree nuts, which have been correctly irradiated to meet insect disinfestation/quarantine requirements, may still contain live insects at the time of importation. There is, however, a movement by plant quarantine authorities away from inspecting to ensure the absence of live insects in imported consignments towards examining through administrative procedures that a treatment required by law has been given. Nevertheless, there is a need to provide plant quarantine inspectors with a reliable objective method to verify that a minimum absorbed dose of radiation was given to supplement administrative procedures. Such an objective method is expected to bolster the confidence of the inspectors in clearing the consignment without delay and to facilitate trade in irradiated commodities. The Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture initiated a co-ordinated research project (CRP) in 1994 to generate data on the verification of absorbed dose of irradiation in fresh, dried fruits and tree nuts for insect disinfestation/quarantine purposes. A standardized label dose indicator available commercially was used to verify the minimum/maximum absorbed dose of the irradiated commodities for these purposes as required by regulations in certain countries. It appears that such a label dose indicator with certain modifications could be made available to assist national authorities and the food industry to verify the absorbed dose of irradiation to facilitate trade in such irradiated commodities. This TECDOC reports on the accomplishments of this co-ordinated research project and includes the papers presented by the participants

Final Technical Report - Kotzebue Wind Power Project - Volume II

Energy Technology Data Exchange (ETDEWEB)

Rana Zucchi, Global Energy Concepts, LLC; Brad Reeve, Kotzebue Electric Association; DOE Project Officer - Doug Hooker

2007-10-31

The Kotzebue Wind Power Project is a joint undertaking of the U.S. Department of Energy (DOE); Kotzebue Electric Association (KEA); and the Alaska Energy Authority (AEA). The goal of the project is to develop, construct, and operate a wind power plant interconnected to a small isolated utility grid in an arctic climate in Northwest Alaska. The primary objective of KEA’s wind energy program is to bring more affordable electricity and jobs to remote Alaskan communities. DOE funding has allowed KEA to develop a multi-faceted approach to meet these objectives that includes wind project planning and development, technology transfer, and community outreach. The first wind turbines were installed in the summer of 1997 and the newest turbines were installed in the spring of 2007. The total installed capacity of the KEA wind power project is 1.16 MW with a total of 17 turbines rated between 65 kW and 100 kW. The operation of the wind power plant has resulted in a wind penetration on the utility system in excess of 35% during periods of low loads. This document and referenced attachments are presented as the final technical report for the U.S. Department of Energy (DOE) grant agreement DE-FG36-97GO10199. Interim deliverables previously submitted are also referenced within this document and where reasonable to do so, specific sections are incorporated in the report or attached as appendices.

Energy-related inventions program invention 637. Final technical report

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-07-31

The final technical report for the Pegasus plow, a stalk and root embedding apparatus, describes progress from the development stage to the product support stage. The US Department of Agriculture - Agriculture Research Service (ARS) is now in the second year of a three year study comparing the Pegasus to conventional tillage. So far, no downside has been with the Pegasus and the following benefits have been documented: (1) Energy savings of 65.0 kilowatt hours per hectare over conventional tillage. This is when the Pegasus plow is used to bury whole stalks, and represents a 70% savings over conventional tillage (92.5 kilowatt hours per hectare). (2) Four to seven fewer passes of tillage, depending on the particular situation. This represents a substantial time savings to farmers. (3) So far, no differences in cotton yields. Recent cotton boll counts in one study indicate a higher yield potential with the Pegasus. (4) No disease problems. (5) Significantly higher levels of organic matter in the soil. A hypothesis of the study is that whole stalk burial may reduce plant disease problems. This hypothesis has not yet been proven. (6) Significantly higher levels of nitrate nitrogen. Total nitrogen and ammonia nitrogen trended higher but were not significantly different. This shows that whole stalk burial does not adversely affect the nitrogen cycle in the soil and may actually improve it. The marketing support stage of the project is also described in the report.

78 FR 50313 - Physical Protection of Irradiated Reactor Fuel in Transit

Science.gov (United States)

2013-08-19

... Irradiated Reactor Fuel in Transit AGENCY: Nuclear Regulatory Commission. ACTION: Orders; rescission. SUMMARY... the NRC published a final rule, ``Physical Protection of Irradiated Fuel in Transit,'' on May 20, 2013... of Irradiated Reactor Fuel in Transit'' (RIN 3150-AI64; NRC-2009-0163). The final rule incorporates...

Report Summarizing the Effort Required to Initiate Welding of Irradiated Materials within the Welding Cubicle

Energy Technology Data Exchange (ETDEWEB)

Frederick, Greg [Electric Power Research Institute (EPRI), Palo Alto, CA (United States); Sutton, Benjamin J. [Electric Power Research Institute (EPRI), Palo Alto, CA (United States); Tatman, Jonathan K. [Electric Power Research Institute (EPRI), Palo Alto, CA (United States); Vance, Mark Christopher [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Smith, Allen W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Clark, Scarlett R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Feng, Zhili [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Miller, Roger G. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Chen, Jian [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Tang, Wei [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hu, Xunxiang [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Gibson, Brian T. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-06-01

The advanced welding facility within a hot cell at the Radiochemical Engineering Development Center of Oak Ridge National Laboratory (ORNL), which has been jointly funded by the U.S. Department of Energy (DOE), Office of Nuclear Energy, Light Water Reactor Sustainability Program and the Electric Power Research Institute, Long Term Operations Program and the Welding and Repair Technology Center, is in the final phase of development. Research and development activities in this facility will involve direct testing of advanced welding technologies on irradiated materials in order to address the primary technical challenge of helium induced cracking that can arise when conventional fusion welding techniques are utilized on neutron irradiated stainless steels and nickel-base alloys. This report details the effort that has been required since the beginning of fiscal year 2017 to initiate welding research and development activities on irradiated materials within the hot cell cubicle, which houses welding sub-systems that include laser beam welding (LBW) and friction stir welding (FSW) and provides material containment within the hot cell.

Food irradiation: an emerging opportunity for African countries

International Nuclear Information System (INIS)

Adu-Gyamfi, A.

2004-01-01

Full Text. The paper reviews the use of food irradiation technology and its potential in food processing and international trade for economic development of African countries. Provision of infrastructure along with technical expertise, private sector anticipation, effective collaborative ventures and networking with other countries and international agencies are considered crucial for Africa to harness the potential of food irradiation. (author)

Postoperative beta irradiation in the treatment of pterygium

International Nuclear Information System (INIS)

Rahman, S.M.; Chung, C.K.; Constable, W.C.

1979-01-01

High recurrence rates are reported after surgical treatment of ptergyia. With the use of beta irradiation, the recurrence rate drops dramatically. This paper describes technic and dosage used in a group of patients receiving postoperative beta irradiation. Two thirds of these patients, however, had at least two surgical procedures. A recurrence rate of 3.5% was observed, with no apparent morbidity

Technical considerations associated with spent fuel acceptance. Final report

International Nuclear Information System (INIS)

Supko, E.M.

1996-06-01

This study was initiated by the Electric Power Research Institute (EPRI) to identify technical considerations associated with spent fuel acceptance and implementation of a waste management system that includes the use of transportable storage systems, and to serve as an opening dialogue among Standard Contract Holders and the department of Energy's Office of Civilian Radioactive Waste management (OCRWM) prior to the development of waste acceptance criteria or issuance of a Notice of Proposed Rulemaking by OCRWM to amend the Standard Contract. The original purpose of the Notice of Proposed Rulemaking was to address changes to the Standard Contract to implement a multi-purpose canister based system and to address other issues that were not adequately addressed in the standard contract. Even if DOE does not develop a multi-purpose canister based system for waste acceptance, it will still be necessary to develop waste acceptance criteria in order to accept spent fuel in transportable storage systems that are being deployed for at-reactor storage. In this study, technical issues associated with spent fuel acceptance will be defined and potential options and alternatives for resolution of technical considerations will be explored

Heavy-Section Steel Irradiation Program

International Nuclear Information System (INIS)

Corwin, W.R.

1990-08-01

The primary goal of the Heavy-Section Steel Irradiation Program is to provide a thorough, quantitative assessment of the effects of neutron irradiation on the material behavior (particularly the fracture toughness properties) of typical pressure-vessel steels as they relate to light-water-reactor pressure-vessel integrity. The program includes direct continuation of irradiation studies previously conducted by the Heavy-Section Steel Technology Program augmented by enhanced examinations of the accompanying microstructural changes. Effects of specimen size; material chemistry; product form and microstructure; irradiation fluence, flux, temperature, and spectrum; and postirradiation annealing are examined on a wide range of fracture properties. Detailed statistical analyses of the fracture data on K Ic shift of high-copper welds were performed. Analysis of the first phase of irradiated crack-arrest testing on high-copper welds was completed. Final analysis and publication of the results of the second phase of the irradiation studies on stainless steel weld-overlay cladding were completed. Determinations were made of the variations in chemistry and unirradiated RT NDT of low upper-shelf weld metal from the Midland reactor. Final analyses were performed on the Charpy impact and tensile data from the Second and Third Irradiation series on low upper-shelf welds, and the report on the series was drafted. A detailed survey of existing data on microstructural models and data bases of irradiation damage was performed, and initial development of a reaction-rate-based model was completed. 40 refs., 7 figs., 4 tabs

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Held, Isaac [Princeton Univ., NJ (United States); Balaji, V. [Princeton Univ., NJ (United States); Fueglistaler, Stephan [Princeton Univ., NJ (United States)

2016-09-19

We have constructed and analyzed a series of idealized models of tropical convection interacting with large-scale circulations, with 25-50km resolution and with 1-2km cloud resolving resolution to set the stage for rigorous tests of convection closure schemes in high resolution global climate models. Much of the focus has been on the climatology of tropical cyclogenesis in rotating systems and the related problem of the spontaneous aggregation of convection in non-rotating systems. The PI (Held) will be delivering the honorary Bjerknes lecture at the Fall 2016 AGU meeting in December on this work. We have also provided new analyses of long-standing issues related to the interaction between convection and the large-scale circulation: Kelvin waves in the upper troposphere and lower stratosphere, water vapor transport into the stratosphere, and upper tropospheric temperature trends. The results of these analyses help to improve our understanding of processes, and provide tests for future high resolution global modeling. Our final goal of testing new convections schemes in next-generation global atmospheric models at GFDL has been left for future work due to the complexity of the idealized model results meant as tests for these models uncovered in this work and to computational resource limitations. 11 papers have been published with support from this grant, 2 are in review, and another major summary paper is in preparation.

Investigation of high purity beryllium for the International Thermonuclear Experimental Reactor (ITER), Task 002. Final report

International Nuclear Information System (INIS)

Vagin, S.P.

1995-05-01

The report includes a description of experimental abilities of Solid Structure Research Laboratory of IAE NNC RK, a results of microstructural characterization of A-4 grade polycrystal Beryllium produced at the Ulba metal plant and a technical project-for irradiation experiments. Technical project contains a detailed description of five proposed experiments, clearing behavior of Beryllium materials under the influence of irradiation, temperature, helium and hydrogen accumulation. Complex irradiation jobs, microstructural investigations and mechanical tests are planned in the framework of these experiments

Issues in food irradiation

International Nuclear Information System (INIS)

Mills, S.

1987-04-01

This discussion paper has two goals: first, to raise public awareness of food irradiation, an emerging technology in which Canada has the potential to build a new industry, mainly oriented to promising overseas markets; and second, to help build consensus among government and private sector decision makers about what has to be done to realize the domestic and export potential. The following pages discuss the potential of food irradiation; indicate how food is irradiated; outline the uses of food irradiation; examine questions of the safety of the equipment and both the safety and nutritional value of irradiated food; look at international commercial developments; assess the current and emerging domestic scene; and finally, draw some conclusions and offer suggestions for action

Summary report of consultants meeting on IAEA International Database on Irradiated Nuclear Graphite Properties. 11. meeting of the Technical Steering Committee

International Nuclear Information System (INIS)

Humbert, D.; Wickham, A.J.

2009-05-01

The 11th Meeting of the Technical Steering Committee for the International Database on Irradiated Nuclear Graphite Properties was held on 25-26 March 2009 at the IAEA Headquarters, Vienna, Austria. All discussions, recommendations and actions of this Consultants' Meeting are recorded in this report. The purposes of the meeting were to review the matters and actions identified in the previous meeting, undertake a review of the current status of the database, and make recommendations for action over the next year. This report contains the status of the identified actions as well as a summary of the recommendations on enhancements to the database. (author)

Summary report of consultants' meeting - IAEA International Database on Irradiated Nuclear Graphite Properties. 8th meeting of the Technical Steering Committee

International Nuclear Information System (INIS)

Humbert, D.; Wickham, A.J.

2006-05-01

The '8th Meeting of the Technical Steering Committee for the International Database on Irradiated Nuclear Graphite Properties' was held on 15-16 March 2006 at the IAEA Headquarters, Vienna, Austria. All discussions, recommendations and actions of this Consultants' Meeting are recorded in this report. The purposes of the meeting were to review the matters and actions identified in the previous meeting, undertake a review of the current status of the database and make recommendations for actions for the next year. This report contains the current status of the identified actions as well as a summary of the recommendations on enhancements to the database. (author)

Economic Feasibility Study for Using Irradiation Technology in Preservation of Animalism Foods

International Nuclear Information System (INIS)

El Gameel, E.A.

2011-01-01

The present study discus the economic feasibility for the preservation animalism foods by using irradiation technology. This study has included the technical data, regression foretelling for the throughput, determination of irradiators types and radiation sources activity. This study comprises the financial analysis for the establishment animalism foods irradiation facilities (types: tote box, pallet conveyor) and the national return

Neutron irradiation of seeds 2

Energy Technology Data Exchange (ETDEWEB)

1968-10-01

The irradiation of seeds with the fast neutron of research reactors has been hampered by difficulties in accurately measuring dose and in obtaining repeatable and comparable results. Co-ordinated research under an international program organized by the FAO and IAEA has already resulted in significant improvements in methods of exposing seeds in research reactors and in obtaining accurate dosimetry. This has been accomplished by the development of a standard reactor facility for the neutron irradiation of seeds and standard methods for determining fast-neutron dose and the biological response after irradiation. In this program various divisions of the IAEA and the Joint FAO/IAEA Division co-operate with a number of research institutes and reactor centres throughout the world. Results of the preliminary experiments were reported in Technical Reports Series No. 76, ''Neutron Irradiation of Seeds''. This volume contains the proceedings of a meeting of co-operators in the FAO/IAEA Neutron Seed Irradiation Program and other active scientists in this field. The meeting was held in Vienna from 11 to 15 December 1967. Refs, figs and tabs.

Neutron irradiation of seeds 2

International Nuclear Information System (INIS)

1968-01-01

The irradiation of seeds with the fast neutron of research reactors has been hampered by difficulties in accurately measuring dose and in obtaining repeatable and comparable results. Co-ordinated research under an international program organized by the FAO and IAEA has already resulted in significant improvements in methods of exposing seeds in research reactors and in obtaining accurate dosimetry. This has been accomplished by the development of a standard reactor facility for the neutron irradiation of seeds and standard methods for determining fast-neutron dose and the biological response after irradiation. In this program various divisions of the IAEA and the Joint FAO/IAEA Division co-operate with a number of research institutes and reactor centres throughout the world. Results of the preliminary experiments were reported in Technical Reports Series No. 76, ''Neutron Irradiation of Seeds''. This volume contains the proceedings of a meeting of co-operators in the FAO/IAEA Neutron Seed Irradiation Program and other active scientists in this field. The meeting was held in Vienna from 11 to 15 December 1967. Refs, figs and tabs

Final technical report; Mercury Release from Organic matter (OM) and OM-Coated Mineral Surfaces

Energy Technology Data Exchange (ETDEWEB)

Aiken, George

2014-10-02

This document is the final technical report for a project designed to address fundamental processes controlling the release of mercury from flood plain soils associated with East Fork Poplar Creek, Tennessee near the U.S. Department of Energy Oak Ridge facility. The report summarizes the activities, findings, presentations, and publications resulting from an award to the U.S. Geological that were part of a larger overall effort including Kathy Nagy (University of Illinois, Chicago, Ill) and Joseph Ryan (University of Colorado, Boulder, CO). The specific charge for the U.S.G.S. portion of the study was to provide analytical support for the larger group effort (Nagy and Ryan), especially with regard to analyses of Hg and dissolved organic matter, and to provide information about the release of mercury from the floodplain soils.

Developing a training programme for radiation protection officers at industrial irradiators

International Nuclear Information System (INIS)

Davor, P.

2013-04-01

A training programme for staff of irradiation facilities especially radiation safety officers at industrial irradiation facilities has been developed. The programme focused on technical and administrative basis for ensuring radiation safety at the practices. It consists of thirteen modules ranging from fundamentals of radiation, biological effects of ionizing radiation as well as the technical and administrative issues pertinent to radiation safety of the sources. The overall objective of this programme was to build competence in the area of radiation protection and raise the confidence level of staff of industrial irradiation facilities. The modules are structured in a manner that attempts to give a good understanding to participants on safety features of irradiators and use of radiation monitoring equipment. Each module has specific objectives and expected outcome and the course content is also stated under each module. The duration of the whole programme is sixteen weeks and the participants are expected to have some working knowledge in radiation protection and safe use of radiation sources. (au)

Commercialization of irradiated foods in Pakistan

International Nuclear Information System (INIS)

Khan, I.

2001-01-01

Preservation of food by gamma radiation is technically feasible and economically viable under conditions existing in Pakistan. To educate the consumers, programme for dissemination of information regarding food irradiation was implemented to educate the consumers. Test marketing of irradiated products was carried out for 5-6 years and more than 8 tons of irradiated vegetables were sold to consumers who were briefed about the advantages of radiation technology. A number of condiments including pepper and chillies were irradiated on a large scale (more than 10 tons) at the Pakistan Radiation Service (PARAS) during the years 1996-1998. Comprehensive Harmonised food irradiation regulations, covering all foods in seven classes, were approved in 1996. The charges for irradiating various food commodities ranged from US$19.71/ton potatoes (0.10 kGy) to US$38.32/ton for spices (10.0 kGy). Once the techno-economic feasibility is demonstrated, huge post-harvest losses of different food commodities can be avoided. This will make the country not only self-sufficient in food, but with enough surplus for export. (author)

Effects of Low-Dose Alpha-Particle Irradiation in Human Cells: The Role of Induced Genes and the Bystander Effect. Final Technical Report (9/15/1998-5/31/2005)

Energy Technology Data Exchange (ETDEWEB)

Little, John B.

2013-09-17

This grant was designed to examine the cellular and molecular mechanisms for the bystander effect of radiation (initially described in this laboratory) whereby damage signals are passed from irradiated to non-irradiated cells in a population. These signals induce genetic effects including DNA damage, mutations and chromosomal aberrations in the nonirradiated cells. Experiments were carried out in cultured mammalian cells, primarily human diploid cells, irradiated with alpha particles. This research resulted in 17 publications in the refereed literature and is described in the Progress Report where it is keyed to the publication list. This project was initiated at the Harvard School of Public Health (HSPH) and continued in collaboration with students/fellows at Colorado State University (CSU) and the New Jersey Medical School (NJMS).

Genetic structure of natural populations: Final technical report

International Nuclear Information System (INIS)

Ayala, F.J.

1987-01-01

We determined the LD 50 for individuals with any one of four genetic constitutions. The LD 50 was in kR units (S and F refer to the two common alleles found in natural populations and N is a mull allele) S/S 5.31, F/F 4.61, S/F 4.19, N/N 3.16. These results are as expected under the hypothesis the SOD is involved in radio-resistance and the degree of protection is a function of SOD specific activity. S codes for an allozyme that has the highest in vitro specific activity while N reduces the amount of enzyme to 3.5% of the normal level. Natural selection experiments in population cages were carried out for 13 generations. In control populations, the frequency of the S allele decreases from the initial frequency of 0.50 to an equilibrium value 0.1 to 0.2 in about 10 generations. In populations with the larvae receiving 4 KR in each generation, s reaches an equilibrium frequency of 0.6; when the irradiation was no longer applied, the frequency of S started declining, eventually reaching 0.1 to 0.2. These results corroborate the hypothesis that SOD protects against irradiation and that the degree of protection is correlated by the in vitro specific activity of the allozymes. 29 refs., 4 tabs

Prospects for food irradiation

International Nuclear Information System (INIS)

Kilcast, David

1990-01-01

Recent legislation will permit the introduction of food irradiation in the UK. This development has been met with protests from consumer groups, and some wariness among retailers. David Kilcast, of the Leatherhead Food Research Association, explains the basic principles and applications of food irradiation, and argues that a test marketing campaign should be initiated. The consumer, he says, will have the final say in the matter. (author)

Selection and Studies of a site for a contract food irradiator

International Nuclear Information System (INIS)

Henon, Y.

1986-09-01

The success of a contract irradiation business greatly depends on the choice of the plant location. The decision should be primarily based on the market studies indicating the location of the main customers. However sufficient infrastructure should be available and places like harbors generally appear as highly favourable. While the establishment of an electron beam accelerator requires few particular studies, some technical points must be checked before considering the construction of a gamma irradiator. Preliminary technical studies may be needed regarding aspects such as quake hazards and hydreological profile. However, in very rare occurrences only should the data make another choice necessary

Design and prefactibility study for the installation of multipourpose gama irradiation

International Nuclear Information System (INIS)

Mata, Carlos; Rios, Guillermo; Orbe, Fredie

1990-01-01

In this work we have developed a technical and economical study for the stablishment of a industrial gamma irradiation facility in Ecuador. This facility would have a multiple use, it could be used in two principal fields: sterilization of disposable medical supplies and food preservation. The technical study is related with the desing of the irradiator source and the calculation of shielding walls and the selection of same important equipments. The economical study foresees a useful life of ten years in ral values and actual values related to the year of installation wich is considered the initial year

Food irradiation: technology transfer to developing countries

International Nuclear Information System (INIS)

Kunstadt, Peter

1990-01-01

This paper discusses Nordion's experiences to-date with the Food Irradiation Project in Thailand (1987-1990). This project will enable the Government of Thailand and the Thai food industry to benefit from established Canadian technology in food irradiation. It includes the design and the construction in Thailand of a multipurpose irradiation facility, similar to the Canadian Irradiation Centre. In addition Canada provides the services, for extended periods of time, of construction and installation management and experts in facility operation, maintenance and training. The Technology Transfer component is a major part of the overall Thai Food Irradiation Project. Its purpose is to familiarize Thai government and industry personnel with Canadian requirements in food regulations and distribution and to conduct market and consumer tests of selected Thai irradiated food products in Canada, once the products have Canadian regulatory approval. On completion of this project, Thailand will have the necessary facility, equipment and training to continue to provide leadership in food irradiation research, as well as scientific and technical support to food industries not only in Thailand but also in the ASEAN region. (author)

Food irradiation: Technology transfer to developing countries

Science.gov (United States)

Kunstadt, Peter

This paper discusses Nordion's experiences to-date with the Food Irradiation Project in Thailand (1987-1990). This project will enable the Government of Thailand and the Thai food industry to benefit from established Canadian technology in food irradiation. It includes the design and the construction in Thailand of a multipurpose irradiation facility, similar to the Canadian Irradiation Centre. In addition Canada provides the services, for extended periods of time, of construction and installation management and experts in facility operation, maintenance and training. The Technology Transfer component is a major part of the overall Thai Food Irradiation Project. Its purpose is to familiarize Thai government and industry personnel with Canadian requirements in food regulations and distribution and to conduct market and consumer tests of selected Thai irradiated food products in Canada, once the products have Canadian regulatory approval. On completion of this project, Thailand will have the necessary facility, equipment and training to continue to provide leadership in food irradiation research, as well as scientific and technical support to food industries not only in Thailand by also in the ASEAN region.

Food irradiation: technology transfer to developing countries

Energy Technology Data Exchange (ETDEWEB)

Kunstadt, Peter [Nordion International Inc., Kanata, ON (Canada)

1990-01-01

This paper discusses Nordion's experiences to-date with the Food Irradiation Project in Thailand (1987-1990). This project will enable the Government of Thailand and the Thai food industry to benefit from established Canadian technology in food irradiation. It includes the design and the construction in Thailand of a multipurpose irradiation facility, similar to the Canadian Irradiation Centre. In addition Canada provides the services, for extended periods of time, of construction and installation management and experts in facility operation, maintenance and training. The Technology Transfer component is a major part of the overall Thai Food Irradiation Project. Its purpose is to familiarize Thai government and industry personnel with Canadian requirements in food regulations and distribution and to conduct market and consumer tests of selected Thai irradiated food products in Canada, once the products have Canadian regulatory approval. On completion of this project, Thailand will have the necessary facility, equipment and training to continue to provide leadership in food irradiation research, as well as scientific and technical support to food industries not only in Thailand but also in the ASEAN region. (author).

Study on the technical feasibility of Fission-Track dating at two irradiation positions of the RA-6 research reactor

International Nuclear Information System (INIS)

Dorval, Eric

2005-01-01

The method of Fission-Track dating is based upon the detection of the damage caused by fission fragments from the Uranium contained in geological samples.In order to determine the age of a sample, both the amount of spontaneous fissions occurred and the Uranium concentration must be known.The latter requires the irradiation of the samples inside a reactor with a well-thermalized flux, so that fissions are induced over 235 U targets only. Therefore, the Uranium concentration may be determined.The main inconvenient presented by the irradiation sites at the RA-6 MTR-type reactor is that neutron flux is not completely thermal there, which means that fissions due to epithermal and fast neutrons will not be negligible.In the same way, tracks due to fissions of 238 U and 232 Th will be detected. In order to know the corrections that must be applied to those measurements performed in this reactor, it is necessary to characterize fast flux.Because of it, this laboratory's gamma spectrometry equipment had to be calibrated. After that, several activation detectors were irradiated and results were analyzed. Finally, it was determined that it is feasible to Fission-Track date at the I6 position. However, limitations associated to this method were analyzed for the values of flux measured in the different sites

Microscopic heavy-ion theory. Final technical report, June 1, 1993 - May 31, 1996

International Nuclear Information System (INIS)

Ernst, D.J.; Oberacker, V.E.; Umar, A.S.

1998-01-01

In this Final Technical Report, the authors summarize the research activities of the three Principal Investigators (Professors Ernst, Oberacker, and Umar) at Vanderbilt University since the last reporting period through the subject award expiration date (Dec. 31, 1996) under contract DE-FG05-87ER40376 with the Department of Energy. The research effort is divided between the following three areas: nuclear structure and astrophysics (microscopic nuclear structure studies and properties of exotic nuclei at HRIBF, supernovae calculations in connection with nuclear astrophysics, and nuclear viscosity studies via muon-induced fission at PSI); pion and kaon interactions with the nucleus at high energies (interaction of pions and kaons with nuclei from low energies to 1 GeV, propagation of excited hadrons in the nuclear medium as probed by pion and electron induced reactions); nuclear physics at high energies (dynamical string-parton model to study multi-particle production at RHIC, electromagnetic lepton pair production at RHIC)

New applications of old processes in nondestructive testing - irradiation and backscatter methods

International Nuclear Information System (INIS)

Segebade, C.

1995-01-01

The application of two non-destructive test processes based on photon irradiation measurement is described. The photon backscatter process and the irradiation measurement were used in the technical field and in examining artificial articles. With the aid of the two beam absorption method, wall thicknesses on large liquid containers made of polyethylene and of steel were measured. The same process with a somewhat modified test rig was used in measuring pipe wall thickness on an antique musical instrument. The components made of turbine blade material were excited to X-ray fluorescence with a source of radio nuclides and analysed with a semiconductor detector. This is particularly advantageous for elements which cannot be determined or can only be determined with difficulty by 'conventional' methods (e.g.: yttrium, rhenium). Also the wall thickness measurement for large (diameter approx. 6 m) plastic pipes with the aid of gamma backscatter is described, as is humidity measurement in brick material. Finally, there is a report on wood profile measurement in a stringed instrument with the aid of gamma backscatter. (orig./HP) [de

Final report of the HFIR [High Flux Isotope Reactor] irradiation facilities improvement project

International Nuclear Information System (INIS)

Montgomery, B.H.; Thoms, K.R.; West, C.D.

1987-09-01

The High-Flux Isotope Reactor (HFIR) has outstanding neutronics characteristics for materials irradiation, but some relatively minor aspects of its mechanical design severely limited its usefulness for that purpose. In particular, though the flux trap region in the center of the annular fuel elements has a very high neutron flux, it had no provision for instrumentation access to irradiation capsules. The irradiation positions in the beryllium reflector outside the fuel elements also have a high flux; however, although instrumented, they were too small and too few to replace the facilities of a materials testing reactor. To address these drawbacks, the HFIR Irradiation Facilities Improvement Project consisted of modifications to the reactor vessel cover, internal structures, and reflector. Two instrumented facilities were provided in the flux trap region, and the number of materials irradiation positions in the removable beryllium (RB) was increased from four to eight, each with almost twice the available experimental space of the previous ones. The instrumented target facilities were completed in August 1986, and the RB facilities were completed in June 1987

Head Start Impact Study. Technical Report

Science.gov (United States)

Puma, Michael; Bell, Stephen; Cook, Ronna; Heid, Camilla; Shapiro, Gary; Broene, Pam; Jenkins, Frank; Fletcher, Philip; Quinn, Liz; Friedman, Janet; Ciarico, Janet; Rohacek, Monica; Adams, Gina; Spier, Elizabeth

2010-01-01

This Technical Report is designed to provide technical detail to support the analysis and findings presented in the "Head Start Impact Study Final Report" (U.S. Department of Health and Human Services, January 2010). Chapter 1 provides an overview of the Head Start Impact Study and its findings. Chapter 2 provides technical information on the…

[Alaskan commodities irradiation project: An options analysis study

International Nuclear Information System (INIS)

Zarling, J.P.; Swanson, R.B.; Logan, R.R.

1989-09-01

The ninety-ninth US Congress commissioned a six-state food irradiation research and development program to evaluate the commercial potential of this technology. Hawaii, Washington, Iowa, Oklahoma and Florida as well as Alaska have participated in the national program; various food products including fishery products, red meats, tropical and citrus fruits and vegetables have been studied. The purpose of the Alaskan study was to review and evaluate those factors related to the technical and economic feasibility of an irradiator in Alaska. This options analysis study will serve as a basis for determining the state's further involvement in the development of food irradiation technology

Progress in food irradiation: Germany

International Nuclear Information System (INIS)

Diehl, J.F.

1978-01-01

The report on German results of irradiation of food covers the period from 1975 to 1978. Special attention is paid to the radiation-chemical changes of food, radiation microbiology with regard to clostridium botulinum, the enzymatic behaviour, physical alterations in several sorts of meat and vegetables after irradiation, tolerability investigations, mutagenicity tests, and, finally, legal aspects. (AJ) [de

Evaluation of neutron irradiation embrittlement in the Korean reactor pressure vessel steels (Final Report)

Energy Technology Data Exchange (ETDEWEB)

Hong, J. H.; Lee, B. S.; Chi, S. H.; Kim, J. H.; Oh, Y. J.; Yoon, J. H.; Kwon, S. C.; Park, D. G.; Kang, Y. H.; Choo, K. N.; Oh, J. M.; Park, S. J.; Kim, B. K.; Shin, Y. T.; Cho, M. S.; Sohn, J. M.; Kim, D. S.; Choo, Y. S.; Ahn, S. B.; Oh, W. H. [Korea Atomic Energy Research Institute, Taejeon (Korea)

2001-05-01

Reactor pressure vessel materials, which were produced by a domestic company, Doosan Heavy Industries and construction Co., Ltd., have been evaluated using the neutron irradiation facility HANARO. For this evaluation, instrumented capsules were used for neutron irradiation of various kinds of specimens made of different heats of steels, which are VCD(Y4), VCD+Al(U4), Si+Al(Y5), U4 weld metal, and U4 HAZ, respectively. The fast neutron fluence levels ranged 1 to 5 (x10{sup 19} n/cm{sup 2}, E>1MeV) depending on the specimens and the irradiation temperature was controlled within 290{+-}10 deg C. The test results showed that, in the ranking of the material properties of the base metals, both before and after neutron irradiation, Y5 is the best, U4 the next and Y4 the last. Y4 showed a substantial change by neutron irradiation as well as the properties was worse than others in the unirradiated state. However, Y5, which showed the best properties in unirradiated state, was also the best in the resistance for irradiation embrittlement and one can hardly detect the property change after irradiation. The weldment showed a reasonably good resistance to irradiation embrittlement while the unirradiated properties were worse than base metals. The RPV steels are all expected to meet the screening criteria of the USNRC codes and regulations during the end of plant life. 39 refs., 42 figs., 27 tabs. (Author)

Gamma Irradiation Facility at Sandia National Laboratories, Albuquerque, New Mexico. Final environmental assessment

International Nuclear Information System (INIS)

1995-11-01

The US Department of Energy (DOE) has prepared an environmental assessment (EA) on the proposed construction and operation of a new Gamma Irradiation Facility (GIF) at Sandia National Laboratories/New Mexico (SNL/NM). This facility is needed to: enhance capabilities to assure technical excellence in nuclear weapon radiation environments testing, component development, and certification; comply with all applicable ES and H safeguards, standards, policies, and regulations; reduce personnel radiological exposure to comply with ALARA limits in accordance with DOE orders and standards; consolidate major gamma ray sources into a central, secured area; and reduce operational risks associated with operation of the GIF and LICA in their present locations. This proposed action provides for the design, construction, and operation of a new GIF located within TA V and the removal of the existing GIF and Low Intensity Cobalt Array (LICA). The proposed action includes potential demolition of the gamma shield walls and removal of equipment in the existing GIF and LICA. The shielding pool used by the existing GIF will remain as part of the ACRR facility. Transportation of the existing 60 Co sources from the existing LICA and GIF to the new facility is also included in the proposed action. Relocation of the gamma sources to the new GIF will be accomplished by similar techniques to those used to install the sources originally

Technical advisory panel for the large acceptance spectrometer: Final report

International Nuclear Information System (INIS)

1989-01-01

The Technical Advisory Panel for the Large Acceptance Spectrometer met on November 17--19, 1988, at CEBAF to perform a second review of the status of this project. The charge to the Panel was ''to provide technical advice to the CEBAF directorate on the design, construction, cost, schedule, and implementation of the Large Acceptance Spectrometer.'' In this written report, an overview of the entire project is given. Specific comments on the major components, data handling and analysis, assembly and installation, and management are presented. The Panel's conclusions are contained in the Executive Summary at the beginning of the report

The biochemical changes of bone collagen after high-dose irradiation

International Nuclear Information System (INIS)

Tajiri, Ken

1980-01-01

In our clinic, patients with malignant bone tumors have been treated by high-dose irradiation therapy, 10,000-20,000 rads, for primary lesions. In order to study the biochemical changes of normal bone around tumor tissue, especially bone collagen, after high-dose irradiation, the author performed the following experiments. The right knee joint of rabbits was irradiated with either 6,000, 10,000, or 15,000 rads by 60 Co-γ ray. The cortical bone of the right tibial metaphysis was used for analyses and compared with the left tibia of the same rabbit. These studies were followed for one year after the final irradiation. The calcium, phosphorous and collagen contents of irradiated bone were remarkably changed. These data indicate that collagen biosynthesis of irradiated bone was decreased and the calcification was disturbed. An increase in the amount of total soluble collagen and a decrease in the amount of hydroxylysine bound sugar were observed. The ratio of β to α chains of the collagen molecule was also changed by the irradiation. The amount of reducible cross-links per hydroxyproline residue was strikingly increased three months after the final irradiation. These changes were remarkable especially in the 10,000 and 15,000 rads irradiated group and found to be recovered approximately six months to one year after the final irradiation. These findings indicate that high-dose irradiation reduces the stability of bone collagen both with the destruction of sugar bonds of hydroxylysine residues and the replacement of matured collagen matrix to immatured one which contain mostly labile reducible cross-links. (author)

System-Cost-Optimized Smart EVSE for Residential Application: Final Technical Report including Manufacturing Plan

Energy Technology Data Exchange (ETDEWEB)

Zhu, Charles [Delta Products, Triangle Park, NC (United States)

2015-05-15

In the 2nd quarter of 2012, a program was formally initiated at Delta Products to develop smart-grid-enabled Electric Vehicle Supply Equipment (EVSE) product for residential use. The project was funded in part by the U.S. Department of Energy (DOE), under award DE-OE0000590. Delta products was the prime contractor to DOE during the three year duration of the project. In addition to Delta Products, several additional supplier-partners were engaged in this research and development (R&D) program, including Detroit Edison DTE, Mercedes Benz Research and Development North America, and kVA. This report summarizes the program and describes the key research outcomes of the program. A technical history of the project activities is provided, which describes the key steps taken in the research and the findings made at successive stages in the multi-stage work. The evolution of an EVSE prototype system is described in detail, culminating in prototypes shipped to Department of Energy Laboratories for final qualification. After the program history is reviewed, the key attributes of the resulting EVSE are described in terms of functionality, performance, and cost. The results clearly demonstrate the ability of this EVSE to meet or exceed DOE's targets for this program, including: construction of a working product-intent prototype of a smart-grid-enabled EVSE, with suitable connectivity to grid management and home-energy management systems, revenue-grade metering, and related technical functions; and cost reduction of 50% or more compared to typical market priced EVSEs at the time of DOE's funding opportunity announcement (FOA), which was released in mid 2011. In addition to meeting all the program goals, the program was completed within the original budget and timeline established at the time of the award. The summary program budget and timeline, comparing plan versus actual values, is provided for reference, along with several supporting explanatory notes. Technical

Optimation of patient positioning and irradiation field documentation when irradiating in oto-rhino-laryngological area

International Nuclear Information System (INIS)

Proske, H.

1992-01-01

The large mobility of head and neck requires, when irradiating in this area, positioning and fastening aids, which go beyond simple head bolsters or head moulds. This paper presented describes a positioning system developed by us for irradiating the neck-nose-throat area, which, due to its construction, consists of a non-slipping positioning ground plate and an individually adjustable masking system, which is physiological safe, can be proceeded quickly and exactly, is relatively inexpensive, and is accepted by patients without objections, furthermore since skin markings by drawing field limits onto the face mask are no longer necessary. Various technical aids allow the placement of satellites to spare those body parts which are not irradiated and to installed compensators for the direction of radiation. An integrated cartridge mount enables in a simple way easy production of field control documentation photos. (orig.) [de

Facts about food irradiation. A series of fact sheets from the International Consultative Group on Food Irradiation

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-12-01

The safety and benefits of foods processed by ionizing radiation are well documented. In an effort to provide governments, especially those of developing countries, with scientifically accurate information on issues of general interest to the public, the International Consultative Group on Food Irradiation (ICGFI), which was established under the aegis of the Food and Agriculture Organization of the United Nations (FAO), the World Health Organization (WHO), and the IAEA, decided at its 7th Annual Meeting in Rome, Italy, on October 1990, to issue a series of ''Fact Sheets'' on the subject. ICGFI, an inter-governmental body with a membership of 37 governments, has as one of its mandates the function to provide information to Member States of the FAO, WHO, and IAEA and to the three organizations themselves on the safe and proper use of food irradiation technology. The Fact Sheets included here cover issues relating to: status and trends; scientific and technical terms; food irradiation and radioactivity; chemical changes in irradiated food; nutritional quality of irradiated foods; genetic studies; microbiological safety of irradiated food; irradiation and food safety; irradiation and food additives and residues; packaging of irradiated foods; safety of irradiation facilities; controlling the process; food irradiation costs; and irradiated foods and the consumer. The Fact Sheets have been separately indexed and included in the INIS Database under Reference Numbers 23011206-23011217, 23011319 and 23012743. The Fact Sheets were first issued by the ICGFI Secretariat (Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture, Vienna, Austria) in May 1991.

Facts about food irradiation. A series of fact sheets from the International Consultative Group on Food Irradiation

International Nuclear Information System (INIS)

1991-12-01

The safety and benefits of foods processed by ionizing radiation are well documented. In an effort to provide governments, especially those of developing countries, with scientifically accurate information on issues of general interest to the public, the International Consultative Group on Food Irradiation (ICGFI), which was established under the aegis of the Food and Agriculture Organization of the United Nations (FAO), the World Health Organization (WHO), and the IAEA, decided at its 7th Annual Meeting in Rome, Italy, on October 1990, to issue a series of ''Fact Sheets'' on the subject. ICGFI, an inter-governmental body with a membership of 37 governments, has as one of its mandates the function to provide information to Member States of the FAO, WHO, and IAEA and to the three organizations themselves on the safe and proper use of food irradiation technology. The Fact Sheets included here cover issues relating to: status and trends; scientific and technical terms; food irradiation and radioactivity; chemical changes in irradiated food; nutritional quality of irradiated foods; genetic studies; microbiological safety of irradiated food; irradiation and food safety; irradiation and food additives and residues; packaging of irradiated foods; safety of irradiation facilities; controlling the process; food irradiation costs; and irradiated foods and the consumer. The Fact Sheets have been separately indexed and included in the INIS Database under Reference Numbers 23011206-23011217, 23011319 and 23012743. The Fact Sheets were first issued by the ICGFI Secretariat (Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture, Vienna, Austria) in May 1991

Irradiation of fruit and vegetables for phytosanitary purpose: an overview

International Nuclear Information System (INIS)

Hénon, Yves

2014-01-01

For several years now, the Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture has been actively supporting the development of irradiation as a phytosanitary measure for fresh fruit and vegetables. Besides being environmentally beneficial by replacing some harmful chemical fumigants, it also has the potential to facilitate international trade. The Joint FAO/IAEA Division has participated in the development of six adopted International Standard Phytosanitary Measures (ISPMs) and provided technical expertise to the International Plant Protection Commission (IPPC) Technical Panel on Phytosanitary Treatments (TPPT) to facilitate the successful adoption of 14 irradiation phytosanitary treatments for pests of quarantine importance as part of ISPM 28 (2007), Phytosanitary Treatments for Regulated Pests

Final technical evaluation report for the proposed revised reclamation plan for the Atlas Corporation Moab Mill

International Nuclear Information System (INIS)

1997-03-01

This final Technical Evaluation Report (TER) summarizes the US Nuclear Regulatory Commission staff's review of Atlas Corporation's proposed reclamation plan for its uranium mill tailings pile near Moab, Utah. The proposed reclamation would allow Atlas to (1) reclaim the tailings pile for permanent disposal and long-term custodial care by a government agency in its current location on the Moab site, (2) prepare the site for closure, and (3) relinquish responsibility of the site after having its NRC license terminated. The NRC staff concludes that, subject to license conditions identified in the TER, the proposed reclamation plan meets the requirements identified in NRC regulations, which appear primarily in 10 CFR Part 40. 112 refs., 6 figs., 16 tabs

Irradiation induced effects in zirconium (A review)

International Nuclear Information System (INIS)

Madden, P.K.

1975-06-01

Irradiation creep in zirconium and its alloys is comprehensively discussed. The main theories are outlined and the gaps between them and the observed creep behaviour, indicated. Although irradiation induced point defects play an important role, effects due to irradiation induced dislocation loops seem insignificant. The experimental results suggest that microstructural variations due to prior cold-working or hydrogen injection perturb the irradiation growth and the irradiation creep of zircaloy. Further investigations into these areas are required. One disadvantage of creep experiments lies in their duration. The possibility of accelerated experiments using ion implantation or electron irradiation is examined in the final section, and its possible advantages and disadvantages are outlined. (author)

Sandis irradiator for dried sewage solids. Final safety analysis report

International Nuclear Information System (INIS)

Morris, M.

1980-07-01

Analyses of the hazards associated with the operation of the Sandia irradiator for dried sewage solids, as well as methods and design considerations to minimize these hazards, are presented in accordance with DOE directives

Final Technical Report - SciDAC Cooperative Agreement: Center for Extended Magnetohydrodynamic Modeling/ Transport and Dynamics in Torodial Fusion System

International Nuclear Information System (INIS)

Schanck, Dalton D.

2010-01-01

Final technical report for research performed by Professor Dalton D. Schnack on SciDAC Cooperative Agreement: Center for Extended MHD Modeling, DE-FC02-06ER54870, for the period 7/1/06 to 2/15/08. Principal results for this period are: 1. Development of a model for computational modeling for the primitive form of the extended MMD equations. This was reported as Phys. Plasmas 13, 058103 (2006). 2. Comparison between the NIMROD and M3D codes for simulation of the nonlinear sawtooth crash in the CDXU tokamak. This was reported in Phys. Plasmas 14, 056105 (2006). 3. Demonstration of 2-fluid and gyroviscous stabilization of interchange modes using computational extended MHD models. This was reported in Phys. Rev. Letters 101, 085005 (2008). Each of these publications is attached as an Appendix of this report. They should be consulted for technical details.

GPHS-RTGs in support of the Cassini RTG Program. Addendum to the final technical report, May 1--December 31, 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-12-01

This Addendum to the Cassini GPHS-RTG Program Final Technical Progress Report describes activities performed during the period 1 May 1998 through 31 December 1998, including effort reflecting contract modification M058. These activities include Earth Gravity Assist (EGA) reentry and related analyses which are detailed in Part A, and effort related to the installation of CAGO equipment within Lockheed Martin`s Building 100 facility in Valley Forge, PA, which is detailed in Part B.

GPHS-RTGs in support of the Cassini RTG Program. Addendum to the final technical report, May 1-December 31, 1998

International Nuclear Information System (INIS)

1998-12-01

This Addendum to the Cassini GPHS-RTG Program Final Technical Progress Report describes activities performed during the period 1 May 1998 through 31 December 1998, including effort reflecting contract modification M058. These activities include Earth Gravity Assist (EGA) reentry and related analyses which are detailed in Part A, and effort related to the installation of CAGO equipment within Lockheed Martin's Building 100 facility in Valley Forge, PA, which is detailed in Part B

Radiation and applications: Technical innovation made by industrial irradiation procedures

International Nuclear Information System (INIS)

Wiesner, L.

1986-01-01

The innovation represented by irradiation as a means of industrial process technology lies in the very special way in which energy is introduced into some object in which it initiates reactions. This is based on the penetrating capability of ionizing radiation, which can produce reactive species, especially radicals, inside an object without requiring the whole object to be subjected to such conditions as, e.g., high temperatures or pressures, which would otherwise be needed to initiate the corresponding reactions. This unique advantage of triggering off reactions by means of ionizing radiation results in possibilities of process technology no other procedure can offer. An aspect becoming more and more important is the possibility to replace expensive materials hard to process by cheaper materials brought into a specific form more easily. Irradiation processes can assign to these materials at least some of the properties and combinations of properties, respectively, of higher-grade materials. (orig.) [de

Radiation sources and technical services

International Nuclear Information System (INIS)

Stonek, K.; Satorie, Z.; Vyskocil, I.

1981-01-01

Work is briefly described of the department for sealed sources production of the Institute, including leak testing and surface contamination of sealed sources. The department also provides technical services including the inspections of sealed sources used in medicine and geology and repair of damaged sources. It carries out research of the mechanical and thermal strength of sealed sources and of the possibility of reprocessing used 226 Ra sources. The despatch department is responsible for supplying the entire country with home and imported radionuclides. The department of technical services is responsible for testing imported radionuclides, assembling materials testing, industrial and medical irradiation devices, and for the collection and storage of low-level wastes on a national scale. (M.D.)

Assessment of repair welding technologies of irradiated materials

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-08-15

Damages on reactor internals of stainless steels caused by stress corrosion cracking and fatigue were identified in aged BWR plants. Repair-welding is one of the practical countermeasure candidates to restore the soundness of components and structures. The project of 'Assessment of Repair welding Technologies of Irradiated Materials' has been carried out to develop the technical guideline regarding the repair-welding of reactor internals. In FY 2011, we investigated the fatigue strength of stainless steel SUS316L irradiated by YAG laser welding. Furthermore, revision of the technical guideline regarding the repair-welding of reactor internals was discussed. Diagram of tungsten inert gas (TIG) weld cracking caused by entrapped Helium was modified. Helium concentration for evaluation-free of TIG weld cracking caused by entrapped Helium was revised to 0.007appm from 0.01appm. (author)

Food irradiation development: Malaysian perspective

International Nuclear Information System (INIS)

Zainon Othman

1997-01-01

Malaysia recognised the potential of food irradiation as a technology that can contribute to solving some preservation problems associated with local agricultural produce. Research studies in this technology were initiated in late 1970s and since 1985, all activities pertaining to R and D applications, adoption and technology transfer of food irradiation were coordinated by The National Working Committee on Food Irradiation which comprises of members from research institutes, universities, regulatory agencies and consumer association. To date, technical feasibility studies conducted on 7 food items / agricultural commodities of economic importance demonstrated the efficacy of irradiation in extending shelf-life, improving hygienic quality and overcoming quarantine barriers in trade. Presently, 1 multipurpose Co-60 irradiator (I MCi), 2 gammacells and an electron beam machine (3 MeV) are available at MINT for research and commercial runs. The Malaysian Standards on Guidelines for Irradiation of Food was formulated in 1992 to facilitate application by local food industries. However, Malaysia has not yet commercially adopt the technology. Among many factors contributing to the situation is the apparent lack of interest by food industries and consumers. Consumer attitude study indicated majority of consumers are still unaware of the benefits of the technology and expressed concern for the safety of process and irradiated products due to limited knowledge and adverse publicity by established consumer groups. Although the food processors indicate positive attitude towards food irradiation, there remain many factors delaying its commercial application such as limited knowledge, cost-benefit, logistics and consumer acceptance. On the regulatory aspect, approval is required from the Director-General of Ministry of Health prior to application of irradiation on food and sale of irradiated food but efforts are being geared towards approving irradiation of certain food

Manual of Good Practice in Food Irradiation. Sanitary, Phytosanitary and Other Applications

International Nuclear Information System (INIS)

2015-01-01

Ensuring that the process of irradiating food delivers the desired result consistently is essential for the correct application of the technology and will help to inspire consumer confidence in irradiated food. This publication aims to help operators of irradiation facilities to appreciate and improve their practices and also to provide detailed, yet straightforward, technical information for stakeholders such as food regulators, manufacturers and traders, who also need to understand ‘good practice’

The economics of biomedical waste irradiation: key issues influencing total cost

International Nuclear Information System (INIS)

Wilson, B.K.

1993-01-01

Each application of gamma irradiation technology is different in one or more significant respects. Disinfection of biomedical wastes presents similar technical challenges to sterilization of medical supplies, but the economic issues are dramatically different. Regulatory requirements, site and technology approvals, waste separation/mixing, transportation, irradiator utilization, economies of scale, and end-product disposal can each have a prohibitive or enabling effect on whether irradiation of biomedical wastes makes good financial sense in a particular situation. This paper discusses each of these issues. (author)

Modular Radioisotope Thermoelectric Generator (RTG) Program. Final technical report

Energy Technology Data Exchange (ETDEWEB)

1992-12-31

Section 2.0 of this report summarizes the MOD-RTG reference flight design, and Section 3.0 discusses the Ground Demonstration System design. Multicouple technology development is discussed in Section 4.0, and Section 5.0 lists all published technical papers prepared during the course of the contract.

Final report on a study of coherence in acceptability criteria for the technical aspects of risks associated with potentially hazardous installations

International Nuclear Information System (INIS)

Chicken, J.C.

1988-01-01

This report describes the results of the study that was made, under Contract No ECI-1390-B7221-85D, for the European Atomic Energy Community. The aim of the study was to examine and assess the feasibility of developing coherent and uniform criteria for judging the acceptability of the technical aspects of the risks associated with potentially hazardous installations. The report is arranged in five main parts. First the nature of hazardous installations is considered and this provides the basis for examination of the currently-used technical risk acceptability criteria. Next, the possible forms of criteria are explored and then universally consistent partial and overall technical risk acceptability criteria are proposed. Following this the implications of using the criteria proposed at the design, regulatory and operating levels are examined. Then, by testing the criteria against some real decisions, the practical problems of using the proposed criteria are explored. This leads to consideration of possible alternatives to the proposed criteria. Finally the conclusions that appear to be justified are summarized and the need for further work is identified

Food irradiation - a Northern Ireland dimension

International Nuclear Information System (INIS)

McMurray, C.H.; Stevenson, M.H.

1988-01-01

Irradiation is a technology which has been exploited in a wide variety of industries ranging from sterilization of medical products and polymer modification to applications with respect to food. Whilst food irradiation has recently become a controversial subject, the process has been studied for many years. Many products could be irradiated to advantage and these need to be thoroughly investigated before final recommendations can be made as to the commercial feasibility and suitability of the processing technology in the Northern Ireland context

Irradiation enhanced diffusion and irradiation creep tests in stainless steel alloys

International Nuclear Information System (INIS)

Loelgen, R.H.; Cundy, M.R.; Schuele, W.

1977-01-01

A review is given of investigations on the rate of phase changes during neutron and electron irradiation in many different fcc alloys showing either precipitation or ordering. The diffusion rate was determined as a function of the irradiation flux, the irradiation temperature and the irradiation dose. It was found that the radiation enhanced diffusion in all the investigated alloys is nearly temperature independent and linearly dependent on the flux. From these results conclusions were drawn concerning the properties of point defects and diffusion mechanisms rate determining during irradiation, which appears to be of a common nature for fcc alloys having a similar structure to those investigated. It has been recognized that the same dependencies which are found for the diffusion rate were also observed for the irradiation creep rate in stainless steels, as reported in literature. On the basis of this obervation a combination of measurements is suggested, of radiation enhanced diffusion and radiation enhanced creep in stainless steel alloys. Measurements of radiation enhanced diffusion are less time consuming and expensive than irradiation creep tests and information on this property can be obtained rather quickly, prior to the selection of stainless steel alloys for creep tests. In order to investigate irradiation creep on many samples at a time two special rigs were developed which are distinguished only by the mode of stress applied to the steel specimens. Finally, a few uniaxial tensile creep tests will be performed in fully instrumented rigs. (Auth.)

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Howe, Gary [RTI International, Research Triangle Park, NC (United States); Albritton, John [RTI International, Research Triangle Park, NC (United States); Denton, David [RTI International, Research Triangle Park, NC (United States); Turk, Brian [RTI International, Research Triangle Park, NC (United States); Gupta, Raghubir [RTI International, Research Triangle Park, NC (United States)

2018-01-31

technology has great potential to provide clean syngas from coal and petcoke-based gasification at increased efficiency and at significantly lower capital and operating costs than conventional syngas cleanup technologies. However, before the technology can be deemed ready for scale-up to a full commercial-scale demonstration, additional R&D testing is needed at the site to address the following critical technical risks: WDP sorbent stability and performance; Impact of WDP on downstream cleanup and conversion steps; Metallurgy and refractory; Syngas cleanup performance and controllability; Carbon capture performance and additional syngas cleanup The proposed plan to acquire this additional R&D data involves: Operation of the units to achieve an additional 3,000 hours of operation of the system within the performance period, with a target of achieving 1,000 hours of those hours via continuous operation of the entire integrated pre-commercial demonstration system; Rapid turnaround of repairs and/or modifications required as necessary to return any specific unit to operating status with documentation and lessons learned to support technology maturation, and; Proactive performance of maintenance activities during any unplanned outages and if possible while operating.

NetView technical research

Science.gov (United States)

1993-01-01

This is the Final Technical Report for the NetView Technical Research task. This report is prepared in accordance with Contract Data Requirements List (CDRL) item A002. NetView assistance was provided and details are presented under the following headings: NetView Management Systems (NMS) project tasks; WBAFB IBM 3090; WPAFB AMDAHL; WPAFB IBM 3084; Hill AFB; McClellan AFB AMDAHL; McClellan AFB IBM 3090; and Warner-Robins AFB.

Final technical evaluation report for the proposed revised reclamation plan for the Atlas Corporation Moab Mill

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This final Technical Evaluation Report (TER) summarizes the US Nuclear Regulatory Commission staff`s review of Atlas Corporation`s proposed reclamation plan for its uranium mill tailings pile near Moab, Utah. The proposed reclamation would allow Atlas to (1) reclaim the tailings pile for permanent disposal and long-term custodial care by a government agency in its current location on the Moab site, (2) prepare the site for closure, and (3) relinquish responsibility of the site after having its NRC license terminated. The NRC staff concludes that, subject to license conditions identified in the TER, the proposed reclamation plan meets the requirements identified in NRC regulations, which appear primarily in 10 CFR Part 40. 112 refs., 6 figs., 16 tabs.

Gas evolution as a rapid screening method for detection of irradiated foods

International Nuclear Information System (INIS)

Roberts, P.B.; Chambers, D.M.; Brailsford, G.W.

1996-01-01

A number of detection methods for irradiated foods are in advanced state of development. No single method is likely to be universally applicable but a battery of tests such as thermoluminescence, electron spin resonance and analysis of lipid radiolytic products may soon be available for most foods and technical uses of irradiation. Most of these proposed tests require relatively sophisticated equipment or technical skills and are often time consuming and costly. There would be value in relatively simple tests which could be used as a rapid screening system or confirmatory method. The literature on the use of radiolytic gases as a detection method is limited and this paper extends the above studies. In particular, it extends the work to frozen shellfish, for which irradiation has been used as a commercial decontaminant technique for many years, and considers the effect of storage temperature. Work on poultry is also reported as a cross-reference to earlier work and because irradiated poultry has recently been released into the US retail trade. (author)

Consumer acceptance of irradiated foods

International Nuclear Information System (INIS)

Feenstra, M.H.; Scholten, A.H.

1991-01-01

Although the first experiments on food irradiation were carried out in 1916 in Sweden, food irradiation, is for consumers, a relatively new technology. From the sixties food irradiation has been applied more and more, so that the consumer movement has become alert to this technology. Since then a lot of controversies have arisen in the literature about wholesomeness, safety, effects, etc. Food irradiation is currently permitted on a small scale in about 30 countries; in some countries or states food irradiation has been put under a ban (e.g. Australia, New Zealand, New Jersey). The World Health Organization (WHO) and the Food and Agriculture Organization of the United Nations (FAO) have, however, chosen food irradiation as a safe and sound method for preserving and improving the safety of food. Reactions on the part of the consumer organizations of many countries are however not in favour of or are even opposed to food irradiation. In this chapter consumer acceptance related to technological developments is described, then the convergence of the consumer movement on public opinion and concern on food irradiation is discussed. The need for labelling of irradiated food products is discussed and finally recommendations are given of ways to change consumers attitudes to food irradiation. (author)

Food irradiation development in Japan

International Nuclear Information System (INIS)

Kawabata, T.

1981-01-01

In Japan, the first food irradiation research was carried out on the preservation of fish and fishery products. In 1966, the Atomic Energy Commission of the Japanese Government (JAEC) decided to promote the National Project on Food Irradiation and, in 1967, the Steering Committee on food irradiation research in the Atomic Energy Bureau, Science and Technology Agency, selected the following food items as of economic importance to the country, i.e., potatoes, onions, rice, wheat, ''Vienna'' sausage, ''kamaboko'' (fish meat jelly products) and mandarin oranges. The National Project is expected to finish at the end of the 1981 fiscal year. Based on the studies by the National Project, irradiated potatoes were given ''unconditional acceptance'' for human consumption in 1972. Already in 1973, a commercial potato irradiator was built at Shihoro, Hokkaido. In 1980, the Steering Committee submitted a final report on the effectiveness and wholesomeness studies on irradiated onions to the JAEC. This paper gives a brief explanation of the legal aspects of food irradiation in Japan, and the present status of wholesomeness studies on the seven items of irradiated foods. In addition, topics concerning food irradiation research on ''kamaboko'', especially on the effectiveness and a new detecting method for the irradiation treatment of these products, are outlined. (author)

Final priority; technical assistance to improve state data capacity--National Technical Assistance Center to improve state capacity to accurately collect and report IDEA data. Final priority.

Science.gov (United States)

2013-05-20

The Assistant Secretary for Special Education and Rehabilitative Services announces a priority under the Technical Assistance to Improve State Data Capacity program. The Assistant Secretary may use this priority for competitions in fiscal year (FY) 2013 and later years. We take this action to focus attention on an identified national need to provide technical assistance (TA) to States to improve their capacity to meet the data collection and reporting requirements of the Individuals with Disabilities Education Act (IDEA). We intend this priority to establish a TA center to improve State capacity to accurately collect and report IDEA data (Data Center).

Food irradiation technology

International Nuclear Information System (INIS)

Cetinkaya, N.

1999-01-01

Trade in food and agricultural products is important to all countries, the economies of many developing countries would be significantly improved if they were able to export more food and agricultural products. Unfortunately, many products can not be traded because they are infested with, or hosts to, harmful pests, contaminated with microorganisms, or spoil quickly. Foods contaminated with microorganisms cause economic losses, widespread illness and death. Several technologies and products have been developed to resolve problems in trading food and to improve food safety, but none can provide all the solutions. Irradiation is an effective technology to resolve technical problems in trade of many food and agricultural products, either as a stand- alone technology or in combination with others. As a disinfestation treatment it allows different levels of quarantine security to be targeted and it is one of few methods to control internal pests. The ability of irradiation virtually to eliminate key pathogenic organisms from meat, poultry, and spices is an important public health advantage. In addition to controlling pests and eliminating harmful bacteria, irradiation also extends the storage life of many foods. In the laboratories of Turkish Atomic Energy Authority, many research projects were completed on the effects of gamma irradiation to the storage life of chicken meat, anchovy, Turkish fermented sausage, dried and fresh fruits and vegetables and also research projects were conducted on the effects of gamma irradiation on microorganisms (Salmonella, Campylo-bacteria, E.coli and S.aureus in white and red meat) and parasites (food-borne, trichostrongylus spp. and Nematodes spp.)

Phytosanitary irradiation - Development and application

Science.gov (United States)

Hallman, Guy J.; Loaharanu, Paisan

2016-12-01

Phytosanitary irradiation, the use of ionizing radiation to disinfest traded agricultural commodities of regulated pests, is a growing use of food irradiation that has great continued potential for increase in commercial application. In 2015 approximately 25,000 t of fresh fruits and vegetables were irradiated globally for phytosanitary purposes. Phytosanitary irradiation has resulted in a paradigm shift in phytosanitation in that the final burden of proof of efficacy of the treatment has shifted from no live pests upon inspection at a port of entry (as for all previous phytosanitary treatments) to total dependence on certification that the treatment for target pests is based on adequate science and is commercially conducted and protected from post-treatment infestation. In this regard phytosanitary irradiation is managed more like a hazard analysis and critical control point (HACCP) approach more consistent with food safety than phytosanitation. Thus, phytosanitary irradiation offers a more complete and rigorous methodology for safeguarding than other phytosanitary measures. The role of different organizations in achieving commercial application of phytosanitary irradiation is discussed as well as future issues and applications, including new generic doses.

Irradiation of dates

International Nuclear Information System (INIS)

Farkas, J.; Al-Charchafchy, F.; Al-Shaikhaly, M.H.; Mirjan, J.; Auda, H.

1974-01-01

Testing of the technical feasibility of radurization of fresh dates was attempted. In addition preliminary studies were carried out to investigate the applicability of gamma rays to date syrup manufacture. The varieties Zahdi, Lelwi and Tabarzel were studied at different stages of ripening. The eating quality of fresh dates was not affected significantly by irradiation even with doses of 270 and 540 krad. The duration of the softening process, after-ripening, of dates was prolonged by low doses of 10-30 krad in the majority of the experimental batches. The time period of after-ripening was reduced with 270 krad, as well as with 540 krad as a result of shortening of the induction period, i.e. the time after which the date begins to soften. The microbial spoilage of khalaal Lelwi dates was considerably reduced by irradiation with doses above 90 krad. The dibis yield of fully rutab dates was highly increased by the radiation doses of 375 to 2000 krad. The darkness and viable cell count of dibis pressed from irradiated dates were significantly lower than that of untreated dates. (F.J.)

Microstructural characterization of an irradiated RERTR-6 U-7Mo/AA4043 alloy dispersion fuel plate specimen blister-tested to a final temperature of 500 °C

Science.gov (United States)

Keiser, Dennis D.; Jue, Jan-Fong; Gan, Jian; Miller, Brandon D.; Robinson, Adam B.; Madden, James W.; Ross Finlay, M.; Moore, Glenn; Medvedev, Pavel; Meyer, Mitch

2017-05-01

The Material Management and Minimization (M3) Reactor Conversion Program, in the past called the Reduced Enrichment for Research and Test Reactor (RERTR) Program, is developing low-enriched uranium (LEU) fuels for application in research and test reactors. U-Mo alloy dispersion fuel is one type being developed. Blister testing has been performed on different fuel plate samples to determine the margin to failure for fuel plates irradiated to different fission densities. Microstructural characterization was performed using scanning electron microscopy and transmission electron microscopy on a sample taken from a U-7Mo/AA4043 matrix dispersion fuel plate irradiated in the RERTR-6 experiment that was blister-tested up to a final temperature of 500 °C. The results indicated that two types of grain/cell boundaries were observed in the U-7Mo fuel particles, one with a relatively low Mo content and fission gas bubbles and a second type enriched in Si, due to interdiffusion from the Si-containing matrix, with little evidence of fission gas bubbles. With respect to the behavior of the major fission gas Xe, a significant amount of the Xe was still observed within the U-7Mo fuel particle, along with microns into the AA4043 matrix. For the fuel/matrix interaction layers that form during fabrication and then grow during irradiation, they change from the as-irradiated amorphous structure to one that is crystalline after blister testing. In the AA4043 matrix, the original Si-rich precipitates, which are typically observed in as-irradiated U-Mo dispersion fuel, get consumed due to interdiffusion with the U-7Mo fuel particles during the blister test. Finally, the fission gas bubbles that were originally around 3 nm in diameter and resided on a fission gas superlattice (FGS) in the intragranular regions of as-irradiated U-7Mo fuel grew in size (up to ∼20 nm diameter) during blister testing and, in many areas, are no longer organized as a superlattice.

Microstructural characterization of an irradiated RERTR-6 U-7Mo/AA4043 alloy dispersion fuel plate specimen blister-tested to a final temperature of 500 °C

Energy Technology Data Exchange (ETDEWEB)

Keiser, Dennis D., E-mail: dennis.keiser@inl.gov [Nuclear Fuels and Materials Division, Idaho National Laboratory, P. O. Box 1625, Idaho Falls, ID 83415-6146 (United States); Jue, Jan-Fong; Gan, Jian; Miller, Brandon D.; Robinson, Adam B.; Madden, James W. [Nuclear Fuels and Materials Division, Idaho National Laboratory, P. O. Box 1625, Idaho Falls, ID 83415-6146 (United States); Ross Finlay, M. [Australian Nuclear Science and Technology Organization, PMB 1, Menai, NSW 2234 (Australia); Moore, Glenn; Medvedev, Pavel; Meyer, Mitch [Nuclear Fuels and Materials Division, Idaho National Laboratory, P. O. Box 1625, Idaho Falls, ID 83415-6146 (United States)

2017-05-15

The Material Management and Minimization (M3) Reactor Conversion Program, in the past called the Reduced Enrichment for Research and Test Reactor (RERTR) Program, is developing low-enriched uranium (LEU) fuels for application in research and test reactors. U–Mo alloy dispersion fuel is one type being developed. Blister testing has been performed on different fuel plate samples to determine the margin to failure for fuel plates irradiated to different fission densities. Microstructural characterization was performed using scanning electron microscopy and transmission electron microscopy on a sample taken from a U-7Mo/AA4043 matrix dispersion fuel plate irradiated in the RERTR-6 experiment that was blister-tested up to a final temperature of 500 °C. The results indicated that two types of grain/cell boundaries were observed in the U-7Mo fuel particles, one with a relatively low Mo content and fission gas bubbles and a second type enriched in Si, due to interdiffusion from the Si-containing matrix, with little evidence of fission gas bubbles. With respect to the behavior of the major fission gas Xe, a significant amount of the Xe was still observed within the U-7Mo fuel particle, along with microns into the AA4043 matrix. For the fuel/matrix interaction layers that form during fabrication and then grow during irradiation, they change from the as-irradiated amorphous structure to one that is crystalline after blister testing. In the AA4043 matrix, the original Si-rich precipitates, which are typically observed in as-irradiated U-Mo dispersion fuel, get consumed due to interdiffusion with the U-7Mo fuel particles during the blister test. Finally, the fission gas bubbles that were originally around 3 nm in diameter and resided on a fission gas superlattice (FGS) in the intragranular regions of as-irradiated U-7Mo fuel grew in size (up to ∼20 nm diameter) during blister testing and, in many areas, are no longer organized as a superlattice.

Irradiated ready-to-eat spinach leaves: How information influences awareness towards irradiation treatment and consumer's purchase intention

Science.gov (United States)

Finten, G.; Garrido, J. I.; Agüero, M. V.; Jagus, R. J.

2017-01-01

This article aims to clarify and supply further information on food irradiation acceptance, with particular focus on Argentina and irradiated ready-to-eat (RTE) spinach leaves through an open web-online survey. Results showed that half of respondents did not know food irradiation, but the other half demonstrated uncertainty despite they declared they had knowledge about it; thus, confirming little awareness towards this technology. Respondents who believed in the misleading myth about food irradiation represented 39%, while roughly the same number was doubtful. On the other hand, after supplying informative material, respondents were positively influenced and an increase in acceptance by 90% was found. Finally, 42% of respondents were willing to consume/purchase irradiated RTE spinach leaves, and 35% remained doubtful. Respondents who did not exclude to accept irradiated spinach could be considered potential consumers if intensive campaigns about the benefits of food irradiation were carried out by reliable actors. If the Argentinean RTE market grew, following the world consumption trend towards these products, irradiated spinach leaves could be successfully introduced by making better efforts to inform consumers about food irradiation.

Irradiation of fish, shellfish and frog legs. A compilation of technical data for authorization and control

International Nuclear Information System (INIS)

2000-06-01

The International Consultative Group on Food Irradiation (ICGFI) was established on 9 May 1984 under the aegis of FAO, IAEA and WHO. ICGFI is composed of experts and other representatives designated by governments which have accepted the terms of the 'Declaration' establishing ICGFI and have pledged to make voluntary contributions, in cash or in kind, to carry out the activities of ICGFI. The functions of ICGFI are as follows: (a) To evaluate global developments in the field of food irradiation; (b) To provide a focal point of advice on the application of food irradiation to Member States and the Organization; and (c) To furnish information as required, through the Organization, to the Joint FAO/IAEA/WHO Expert Committee on the Wholesomeness of Irradiated Food, and to the Codex Alimentarius Commission. This publication contains the most up to date data on irradiation of fish, shellfish and frog legs. It is intended to assist governments in considering the authorization of this particular application of radiation processing of food and in ensuring its control in the facility and the control of irradiated food products moving in trade. It was prepared at the request of the International Consultative Group on Food Irradiation (ICGFI) in response to the increasing acceptance and application of irradiation to ensure hygienic quality of food, especially those of animal origin

Irradiation of fish, shellfish and frog legs. A compilation of technical data for authorization and control

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-06-01

The International Consultative Group on Food Irradiation (ICGFI) was established on 9 May 1984 under the aegis of FAO, IAEA and WHO. ICGFI is composed of experts and other representatives designated by governments which have accepted the terms of the 'Declaration' establishing ICGFI and have pledged to make voluntary contributions, in cash or in kind, to carry out the activities of ICGFI. The functions of ICGFI are as follows: (a) To evaluate global developments in the field of food irradiation; (b) To provide a focal point of advice on the application of food irradiation to Member States and the Organization; and (c) To furnish information as required, through the Organization, to the Joint FAO/IAEA/WHO Expert Committee on the Wholesomeness of Irradiated Food, and to the Codex Alimentarius Commission. This publication contains the most up to date data on irradiation of fish, shellfish and frog legs. It is intended to assist governments in considering the authorization of this particular application of radiation processing of food and in ensuring its control in the facility and the control of irradiated food products moving in trade. It was prepared at the request of the International Consultative Group on Food Irradiation (ICGFI) in response to the increasing acceptance and application of irradiation to ensure hygienic quality of food, especially those of animal origin.

Technical report: fabrication of PWR type rodlet fuel

International Nuclear Information System (INIS)

Yanagisawa, Kazuaki; Uno, Hisao; Sasajima, Hideo

1990-06-01

With respect to the simulated reactivity initiated accident (RIA) experiments with pre-irradiated LWR type fuel rods at nuclear safety research reactor (NSRR), there were principally three technical difficulties which should be overcome: (1) Fabrication of the rodlet fuel; Fuel rods from the commercial power reactors had an active column length by 3.6m. To utilize this for NSRR pulse experiment, rodlet fuel having an active column length by 0.12m (reduced to one thirtieth) is requested to fabricate without changing the inside fuel conditions. (2) Development of in-core instrumentations: During pre-irradiation stages, a long-sized fuel rod had dimensional changes by waterside corrosion, bowing, creep down and so on. The fuel also had greater amount of radioactive fission products. This condition is significant to in-core instrumentations to be attached to the fuel rods. Well characterized data to be obtained from these, however, are quite necessary and important from research point of view. Remote handling techniques to attach the rod pressure sensor, the cladding extensometer, the fuel extensometer, and the cladding surface thermocouple to pre-irradiated fuel rods are, therefore, requested to develop. (3) Installation of PIE equipments for pulsed rodlet fuels: PIE on the pulsed rodlet fuels are necessary to better understanding the fuel performance detaily. Equipments which can easily detect the data related to PCMI type fuel failure are matter of concern. Since 1986, the technical difficulties have been tried to overcome by all staffs belonging to Reactivity Accident Laboratory, NSRR Operation Division, Department of Reactor Fuel Examination and Hot Laboratory. This report describes the technical achievements obtained through four years work. (author)

Development of system for product tracking and data acquisition of data irradiation process in large gamma irradiators

International Nuclear Information System (INIS)

Soares, Jose Roberto

2010-01-01

The sterilization of medical care products using ionizing radiation is a consolidated technique. In Brazil there are in operation gamma irradiators with capacity between 0.37 PBq (10kCi) 185 PBq (5 MCi) using radioisotopes 60 Co as radiation source. The developed work provides an accurate control and a data acquisition for the application of Good Manufacturing Practices during all phases of an irradiation process, required by the standards of ANVISA, ISO and IAEA technical recommendations for the treatment of foods and medical products. All the steps involved in the irradiation treatment are mapped into process flow (work flow), where each agent (participant) has its systematized tasks. The data acquisition process, monitoring and control, are based on a set of tools (free software licenses) integrated by a network of efficient communication, including the use of Web resources. Using the Gamma Irradiator Multipurpose IPEN/CNEN/USP all the development was performed to be applied in irradiators facilities operating in industrial scale. The system enables a complete traceability of the process, in real time, for any participant and also the storage of the corresponding records to be audited. (author)

Development of system for product tracking and data acquisition of data irradiation process in large gamma irradiators

International Nuclear Information System (INIS)

Soares, Jose R.; Rela, Paulo R.; Costa, Fabio E.

2011-01-01

The sterilization of medical care products using ionizing radiation is a consolidated technique. In Brazil there are in operation gamma irradiators with capacity between 0.37 PBq (10kCi) 185 PBq (5 MCi) using radioisotopes 60 Co as radiation source. The developed work provides an accurate control and data acquisition for the application of good manufacturing practices during all phases of an irradiation process, required by the standards of ANVISA, technical ISO and IAEA recommendations for the treatment of foods and medical products. All the steps involved in the irradiation treatment are mapped into process flow (work flow), where each agent (participant) has its systematized tasks. The automatic data process acquisition using wireless ZigBee technology, monitoring and control, are based on a set of tools (free software licenses) integrated by a network of efficient communication, including the use of Web resources. Using the Gamma Irradiator Multipurpose IPEN/CNEN-SP all the development was performed to be applied in irradiators' facilities operating in industrial scale. The system enables a complete traceability of the process, in real time, for any participant and also the storage of the corresponding records to be audited. (author)

Development of system for product tracking and data acquisition of data irradiation process in large gamma irradiators

Energy Technology Data Exchange (ETDEWEB)

Soares, Jose R., E-mail: joseroberto.soares@mackenzie.br [Universidade Presbiteriana Mackenzie. Escola de Engenharia. Sao Paulo, SP (Brazil); Rela, Paulo R.; Costa, Fabio E., E-mail: prela@ipen.br, E-mail: fecosta@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2011-07-01

The sterilization of medical care products using ionizing radiation is a consolidated technique. In Brazil there are in operation gamma irradiators with capacity between 0.37 PBq (10kCi) 185 PBq (5 MCi) using radioisotopes {sup 60}Co as radiation source. The developed work provides an accurate control and data acquisition for the application of good manufacturing practices during all phases of an irradiation process, required by the standards of ANVISA, technical ISO and IAEA recommendations for the treatment of foods and medical products. All the steps involved in the irradiation treatment are mapped into process flow (work flow), where each agent (participant) has its systematized tasks. The automatic data process acquisition using wireless ZigBee technology, monitoring and control, are based on a set of tools (free software licenses) integrated by a network of efficient communication, including the use of Web resources. Using the Gamma Irradiator Multipurpose IPEN/CNEN-SP all the development was performed to be applied in irradiators' facilities operating in industrial scale. The system enables a complete traceability of the process, in real time, for any participant and also the storage of the corresponding records to be audited. (author)

Food irradiation for developing countries in Africa

International Nuclear Information System (INIS)

1990-12-01

The amount of post-harvest losses of food is considered to be highest on the African continent. As a result, increasing numbers of countries in Africa are suffering from problems of hunger and malnutrition, which range from chronic to acute. Food irradiation could play an important role in reducing the high rate of food losses especially in the case of food grain, root crops and dried food in this continent provided that proper infrastructure to employ this technique could be identified. Irradiation could contribute positively to the safety of food from microbiological and parasitic infection. A panel of experts participated at the round table discussion to assess the potential application of the technology in Africa. Some of the items for which technical feasibility has been established for food irradiation preservation include yams, onions, potatoes, maize, millet, sorghum, cowpeas and other pulses, cocoa beans, spices (pepper) and condiments, meat and poultry, fish and fishery products, animal feed, etc. In considered the local demand, a suitable choice of the type and size of the facility should be made. The design should allow up-grading in both size and automated operation to meet future expansion of the existing facility, but small commercial scale facilities, of low cost, should be considered to start with. Whatever type of equipment chosen, (whether Gamma or Electron Beam) safety, reliability, maintainability, and simplicity of operation should be of major consideration. It is recognized that for a project to be concluded on a reasonable schedule, technology transfer and training should be incorporated into the complete package. In addition back-up technical infrastructure in the country should be strengthened. The effective procedures demonstrated in a number of countries for performing consumer acceptance studies on irradiated foods, should be adopted in a slightly modified form adapted to the different target populations. Such studies should be

International standards, Agreements and Policy of food Irradiation

International Nuclear Information System (INIS)

Roberts, P.B.

1997-01-01

There are few internationally recognised standards and agreements related to irradiated foods. Codex Alimentarius has its General standard for Irradiated foods. This sets standards for the production of irradiated foods that are safe and nutritionally adequate. Guidelines for the proper processing of foods by irradiation are covered in the Codex Recommended International Code of Practice for the Operation of Radiation Facilities Used for the Treatment of Food. For irradiation as a quarantine treatment for fruit, vegetables and other plants, the relevant international organization is the International Plant Protection Convention (IPPC), IPPC has no standards or guidelines for irradiation treatments. However, regional organizations within IPPC are moving towards recognition of irradiation as a technically viable and effective method of insect disinfestation. Especially notable are actions within the North American Plant Protection Organisation (NAPPO). NAPPO has endorsed a standard on the use of irradiation as a quarantine treatment. Other speakers have provided considerable detail on the Codex standard and on the situation with regard to quarantine issues. In this talk I will concentrate on irradiated foods as commodities that will be traded internationally in increasing amounts as we approach the next century. International trade is governed by bilateral arrangements. However, these arrangements should be consistent with the overarching multilateral agreements of the World trade Organization (WTO). The WTO Agreements do not refer directly to irradiation or irradiated foods. However, in this talk I will try to interpret the implications of the Agreements for trade in irradiated food. (Author)

International standards, Agreements and Policy of food Irradiation

Energy Technology Data Exchange (ETDEWEB)

Roberts, P.B. [Industrial and Biological Section. Institute of Geological and Nuclear Science. P.O. Box 31. Lower Hutt (New Zealand)

1997-12-31

There are few internationally recognised standards and agreements related to irradiated foods. Codex Alimentarius has its General standard for Irradiated foods. This sets standards for the production of irradiated foods that are safe and nutritionally adequate. Guidelines for the proper processing of foods by irradiation are covered in the Codex Recommended International Code of Practice for the Operation of Radiation Facilities Used for the Treatment of Food. For irradiation as a quarantine treatment for fruit, vegetables and other plants, the relevant international organization is the International Plant Protection Convention (IPPC), IPPC has no standards or guidelines for irradiation treatments. However, regional organizations within IPPC are moving towards recognition of irradiation as a technically viable and effective method of insect disinfestation. Especially notable are actions within the North American Plant Protection Organisation (NAPPO). NAPPO has endorsed a standard on the use of irradiation as a quarantine treatment. Other speakers have provided considerable detail on the Codex standard and on the situation with regard to quarantine issues. In this talk I will concentrate on irradiated foods as commodities that will be traded internationally in increasing amounts as we approach the next century. International trade is governed by bilateral arrangements. However, these arrangements should be consistent with the overarching multilateral agreements of the World trade Organization (WTO). The WTO Agreements do not refer directly to irradiation or irradiated foods. However, in this talk I will try to interpret the implications of the Agreements for trade in irradiated food. (Author)

Yucca Mountain Climate Technical Support Representative

International Nuclear Information System (INIS)

Sharpe, Saxon E

2007-01-01

The primary objective of Project Activity ORD-FY04-012, 'Yucca Mountain Climate Technical Support Representative', was to provide the Office of Civilian Radioactive Waste Management (OCRWM) with expertise on past, present, and future climate scenarios and to support the technical elements of the Yucca Mountain Project (YMP) climate program. The Climate Technical Support Representative was to explain, defend, and interpret the YMP climate program to the various audiences during Site Recommendation and License Application. This technical support representative was to support DOE management in the preparation and review of documents, and to participate in comment response for the Final Environmental Impact Statement, the Site Recommendation Hearings, the NRC Sufficiency Comments, and other forums as designated by DOE management. Because the activity was terminated 12 months early and experience a 27% reduction in budget, it was not possible to complete all components of the tasks as originally envisioned. Activities not completed include the qualification of climate datasets and the production of a qualified technical report. The following final report is an unqualified summary of the activities that were completed given the reduced time and funding

Irradiation of potatoes for long-term storage

International Nuclear Information System (INIS)

Srapenjanz, R.

1976-01-01

In the USSR gamma irradiation of potatoes is used for extending the storage life. The properties of potatoes are not changed, and the irradiation procedure is lower in cost than chemical treatments for sprout inhibition. Finally, a brief outline is given of investigations on sprout inhibition of potatoes in other socialist countries

Systems study 'Alternative Entsorgung'. Final report. Technical annex 6

International Nuclear Information System (INIS)

1984-08-01

In the conditioning plant, fuel elements which have been stored for ten years are loaded into transport containers, unloaded, identified and welded into a dry storage box. The dry store barrel is introduced into a final storage container, which, after being closed, is packed in lost shielding. This so-called final storage barrel is finally placed in a transport container and leaves the conditioning plant in this form by rail for transport to the final storage mine. The fuel element method of treatment 'packing of three complete fuel elements' was used as the reference process. In addition, the method of treatment 'fuel elements dismantled into fuel rods' was also examined. The handling of fuel elements and secondary waste treatment in the reference process are described in detail. (orig./HP) [de

Symposium on irradiation for national development. Proceedings

International Nuclear Information System (INIS)

Adesanmi, C.A.; Ogbadu, G.H.

1998-01-01

This document is the full proceedings of the symposium on irradiation for national development held at SHESTCO in 1996. It contains the full texts of a forward, opening and special remarks, welcome and keynote addresses and abstracts and texts of 23 technical papers. The subjects covered included regulations, codes of practice, irradiation technology in food, agriculture and industry, radiation protection and dosimetry. The questions, answers and comments in the discussion sessions are also included. Additionally, the abstracts of 8 other papers are included. We wish to thank the Coordinator of SHESTCO for making available this proceedings

Symposium on irradiation for national development. Proceedings

Energy Technology Data Exchange (ETDEWEB)

Adesanmi, C A; Ogbadu, G H [eds.

1998-12-01

This document is the full proceedings of the symposium on irradiation for national development held at SHESTCO in 1996. It contains the full texts of a forward, opening and special remarks, welcome and keynote addresses and abstracts and texts of 23 technical papers. The subjects covered included regulations, codes of practice, irradiation technology in food, agriculture and industry, radiation protection and dosimetry. The questions, answers and comments in the discussion sessions are also included. Additionally, the abstracts of 8 other papers are included. We wish to thank the Coordinator of SHESTCO for making available this proceedings.

Preliminary studies on the use of irradiation for decontaminating water and sludge in wastewater treatment plants in Chile

International Nuclear Information System (INIS)

Villanueva, Loreto; Schrader, Rosemarie

1999-01-01

This work describes the activities carried out to date by the Chilean Nuclear Energy Commission, CCHEN, in prospecting the application of gamma and electron beam irradiation to the decontamination of sewage water and sludge in the country. Sludge, in particular, will become a relevant environmental problem in the coming years, because of the large amounts that will be generated, due to the construction of many wastewater treatment plants in the country. The main study consisted of experimental gamma irradiation tests on representative samples of digested sludge from two pilot wastewater treatment plants operating in Santiago. This study showed the technical feasibility of using low irradiation doses, of around 2-3 kGy to significantly reduce the pathogen content in this sludge. Preliminary tests were also carried out to determine that the disinfected sludge was fit for agricultural use due to its nutrient content. A preliminary technical and economic evaluation is being prepared on the use of gamma irradiation for sludge disinfection, as a complement to the experimental studies. With this evaluation a feasible process has been outlined for using gamma irradiation in conjunction with conventional processes for the sludge disinfection or hygienization in domestic wastewater treatment plants, in order to produce a useful material for agricultural use that meets the demanding EPA standards when classified as class A sludge, which permits agricultural use without sanitary restrictions. Several evaluations have been made to determine the potential use of irradiation for water and industrial wastewater effluents decontamination, considering normative standards as well as technical and economic aspects. One of these has been the preliminary evaluation of using electron beam irradiation for disinfecting drinking water, which has the technical advantage of preventing the formation of trihalomethanes, that occur in water chlorination due to the presence of natural humic

Heavy-Section Steel Irradiation Program. Volume 5, No. 2, Progress report, April 1994--September 1994

International Nuclear Information System (INIS)

Corwin, W.R.

1995-07-01

The Heavy-Section Steel Irradiation (HSSI) Program has been established with its primary goal to provide a thorough, quantitative assessment of the effects of neutron irradiation on the material behavior and the fracture toughness properties of typical pressure-vessel steels as they relate to light-water RPV integrity. Effects of specimen size; material chemistry; product form and microstructure; irradiation fluence, flux, temperature, and spectrum; and postirradiation annealing are being examined on a wide range of fracture properties. The HSSI Program is arranged into 14 tasks: (1) program management, (2) fracture toughness curve shift in high-copper weldments (Series 5 and 6), (3) K lc and K la curve shifts in low upper-shelf (LUS) welds (Series 8), (4) irradiation effects in a commercial LUS weld (Series 10), (5) irradiation effects on weld heat-affected zone and plate materials (Series 11), (6) annealing effects in LUS welds (Series 9), (7) microstructural and microfracture analysis of irradiation effects, (8) in-service irradiated and aged material evaluations, (9) Japan Power Development Reactor (JPDR) steel examination, (10) fracture toughness curve shift method, (11) special technical assistance, (12) technical assistance for Joint Coordinating Committee on Civilian Nuclear Reactor Safety (JCCCNRS) Working Groups 3 and 12, (13) correlation monitor materials, and (14) test reactor coordination. Progress on each task is reported

Heavy-Section Steel Irradiation Program: Progress report for April--September 1995. Volume 6, Number 2

International Nuclear Information System (INIS)

Corwin, W.R.

1996-08-01

The goal of the Heavy-Section Steel Irradiation Program is to provide a thorough, quantitative assessment of effects of neutron irradiation on material behavior, and in particular the fracture toughness properties, of typical pressure vessel steels as they relate to light-water reactor pressure-vessel integrity. Effects of specimen size, material chemistry, product form and microstructure, irradiation fluence, flux, temperature and spectrum, and post-irradiation annealing are being examined on a wide range of fracture properties. The HSSI Program is arranged into 14 tasks: (1) program management, (2) fracture toughness (K Ic ) curve shift in high-copper welds, (3) crack-arrest toughness (K Ia ) curve shift in high-copper welds, (4) irradiation effects on cladding, (5) K Ic and K Ia curve shifts in low upper-shelf welds, (6) annealing effects in low upper-shelf welds, (7) irradiation effects in a commercial low upper-shelf weld, (8) microstructural analysis of irradiation effects, (9) in-service aged material evaluations, (10) correlation monitor materials, (11) special technical assistance, (12) JPDR steel examination, (13) technical assistance for JCCCNRS Working Groups 3 and 12, and (14) additional requirements for materials. This report provides an overview of the activities within each of these task from April through September 1995

Minutes of the IFMIF technical meetings, May 17-20, 2005, Tokyo, Japan

International Nuclear Information System (INIS)

Ida, Mizuho; Nakamura, Hiroo; Yutani, Toshiaki; Maebara, Sunao; Umetsu, Tomotake; Sugimoto, Masayoshi

2005-08-01

The International Fusion Materials Irradiation Facility (IFMIF) Technical Meetings were held on May 17-20, 2005 at Japan Atomic Energy Research Institute (JAERI) Tokyo. The main objectives were 1) to review technical status of the subsystems; accelerator, target and test facilities, 2) to technically discuss interface issues between target and test facilities, 3) to review results of peer-reviews performed in the EU and Japan, 4) to harmonize design/experimental activities among the subsystems, 5) to review and discuss the Engineering Validation and Engineering Design Activity (EVEDA) tasks, and 6) to make a report of 1) - 5) to the IFMIF Executive Subcommittee. This report presents a brief summary of the Target Technical, Meeting, Test Facilities Technical Meeting, Target/Test Facilities Interface Meeting, Accelerator Technical Meeting and the Technical Integration Meeting. (author)

Selection of irradiator for potato preservation

Energy Technology Data Exchange (ETDEWEB)

Kinsara, A R; Melaibari, A G; Abulfaraj, W H; Mamoon, A M; Kamal, S E [Nuclear Engineering Department, Faculty of Engineering, King Abdulaziz University P.O.Box 9027, Jeddah-21413, (Saudi Arabia)

1997-12-31

A formal decision methodology is a sound approach for assisting in decision making needed for the selection of irradiators for Potato preservation. A formal analysis is preferred over an informal intuitive analysis which has limitations. This will focus on substantial issues and provide the basis for a compromise between conflicting objectives. All critical issues in selection of irradiators for Potato preservation can be addressed within the decision analysis framework. Of special significance is the treatment of the uncertainly associated with consequences of a decision and the preferences of the experts. A decision theory is employed in providing a strategy for implementation of the irradiator selection for food preservation for Saudi Arabia. To select a suitable decision methodology for the present case, a detailed survey of available decision methods was conducted. These methods have been developed and applied with varying degrees of success to many diverse areas of interest. Based on detailed surveys, the Analytic Hierarchy process (AHP) was selected to evaluate the various irradiators for Potato irradiation. These are electron accelerators, X-ray irradiators, and gamma irradiators. The purpose was to determine the optimal. The set of factors impacting irradiator selection were developed and defined to provide comprehensive and realistic variables that judge the represented irradiator alternatives. The factors developed are economic considerations, technical considerations, safety aspects, and compatibility with local environment. The AHP computer program was developed to computerize the tedious complicated computations towards implementing the AHP systematic procedures to solve the present problem. The program was developed using FOXPRO. Based upon the available data, and employing the APH computer program, the results show superiority of {sup 60} Co gamma-ray irradiator over other irradiators for saudi arabia`s present circumstances. 2 figs.,7 tabs.

Establishment of experimental equipments in irradiation technology development building

International Nuclear Information System (INIS)

Ishida, Takuya; Tanimoto, Masataka; Shibata, Akira; Kitagishi, Shigeru; Saito, Takashi; Ohmi, Masao; Nakamura, Jinichi; Tsuchiya, Kunihiko

2011-06-01

The Neutron Irradiation and Testing Reactor Center has developed new irradiation technologies to provide irradiation data with high technical value for the resume of the Japan Materials Testing Reactor (JMTR). For the purpose to perform assembling of capsules, materials tests, materials inspection and analysis of irradiation specimens for the development of irradiation capsules, improvement and maintenance of facilities were performed. From the viewpoint of effective use of existing buildings in the Oarai research and development center, the RI application development building was refurbished and maintained for above-mentioned purpose. The RI application development building is a released controlled area, and was used as storage of experimental equipments and stationeries. The building was named 'Irradiation Technology Development Building' after it refurbished and maintained. Eight laboratories were maintained based on the purpose of use, and the installation of the experimental apparatuses was started. A basic management procedure of the Irradiation Technology Development Building was established and has been operated. This report describes the refurbish work of the RI application development building, the installation and operation method of the experimental apparatuses and the basic management procedure of the Irradiation Technology Development Building. (author)

IRIS Final Technical Progress Report

Energy Technology Data Exchange (ETDEWEB)

M. D. Carelli

2003-11-03

OAK-B135 This NERI project, originally started as the Secure Transportable Autonomous Light Water Reactor (STAR-LW) and currently known as the International Reactor Innovative and Secure (IRIS) project, had the objective of investigating a novel type of water-cooled reactor to satisfy the Generation IV goals: fuel cycle sustainability, enhanced reliability and safety, and improved economics. The research objectives over the three-year (1999-2002) program were as follows: First year: Assess various design alternatives and establish main characteristics of a point design; Second year: Perform feasibility and engineering assessment of the selected design solutions; Third year: Complete reactor design and performance evaluation, including cost assessment These objectives were fully attained and actually they served to launch IRIS as a full fledged project for eventual commercial deployment. The program did not terminate in 2002 at the end of the NERI program, and has just entered in its fifth year. This has been made possible by the IRIS project participants which have grown from the original four member, two-countries team to the current twenty members, nine countries consortium. All the consortium members work under their own funding and it is estimated that the value of their in-kind contributions over the life of the project has been of the order of $30M. Currently, approximately 100 people worldwide are involved in the project. A very important constituency of the IRIS project is the academia: 7 universities from four countries are members of the consortium and five more US universities are associated via parallel NERI programs. To date, 97 students have worked or are working on IRIS; 59 IRIS-related graduate theses have been prepared or are in preparation, and 41 of these students have already graduated with M.S. (33) or Ph.D. (8) degrees. This ''final'' report (final only as far as the NERI program is concerned) summarizes the work performed

Manual of Good Practice in Food Irradiation. Sanitary, Phytosanitary and Other Applications (Spanish Edition)

International Nuclear Information System (INIS)

2017-01-01

Ensuring that the process of irradiating food delivers the desired result consistently is essential for the correct application of the technology and will help to inspire consumer confidence in irradiated food. This publication aims to help operators of irradiation facilities to appreciate and improve their practices and also to provide detailed, yet straightforward, technical information for stakeholders such as food regulators, manufacturers and traders, who also need to understand ‘good practice’.

Food irradiation: physical-chemical, technological and economical background and competing methods of food preservation

International Nuclear Information System (INIS)

Zagorski, Z.P.

1994-01-01

Physical, chemical and technical as well as economical background of food preservation by irradiation have been performed. The radiation sources and the elements of radiation chemistry connected with their use in food irradiation process have been shown. The problems of dosimetry and endurance of dose uniformity for processed products have been also discussed. The other methods of food preservation and their weakness and advantages have been also presented and compared with food irradiation method

Analysis of Technical Feasibility of Traveling Wave Reactor

International Nuclear Information System (INIS)

Kim, Sang Ji; Yoo, Jae Woon; Bae, In Ho

2011-01-01

The status and trend of TWR, patent status and its major technical characteristics were examined in this study. Main technical features of traveling wave reactor can be characterized as a reactor operation without refueling up to the reactor life more than 60 years and TWR utilizes depleted uranium which would be produced from the enrichment process as a byproduct. Enriched fuel is only loaded to an igniter which is required for initiation of burning wave. In this study, quantitative analysis of TWR arising from the technical features was carried out in terms of resource utilization, safety and integrity, and proliferation resistance. In parallel with the concept review of TerraPower SWR design concepts, independent analysis of SWR design by altering a design specification and operation strategy was done in this study. The fuel rod design of SWR was also investigated based on the current database of fuel irradiation and performance. The technical issues of TWR or SWR which should be prior to detailed research and development can be summarized as follows: ·Strong physical protection is required during the shuffling or in-service inspection period to improve the proliferation resistance. ·New flow control logic or device is required for distributing the assembly-wise flow to be corresponded with power swing of fuel assembly. ·High integrity cladding material need to be developed for covering the high fast neutron fluence more than three times of current limit which result from the high burnup and long fuel cycle. The metal fuel under the high burnup condition should be validated through the irradiation test

Technical Letter Report on the Cracking of Irradiated Cast Stainless Steels with Low Ferrite Content

Energy Technology Data Exchange (ETDEWEB)

Chen, Y. [Argonne National Lab. (ANL), Argonne, IL (United States); Alexandreanu, B. [Argonne National Lab. (ANL), Argonne, IL (United States); Natesan, K. [Argonne National Lab. (ANL), Argonne, IL (United States)

2014-11-01

Crack growth rate and fracture toughness J-R curve tests were performed on CF-3 and CF-8 cast austenite stainless steels (CASS) with 13-14% of ferrite. The tests were conducted at ~320°C in either high-purity water with low dissolved oxygen or in simulated PWR water. The cyclic crack growth rates of CF-8 were higher than that of CF-3, and the differences between the aged and unaged specimens were small. No elevated SCC susceptibility was observed among these samples, and the SCC CGRs of these materials were comparable to those of CASS alloys with >23% ferrite. The fracture toughness values of unirradiated CF-3 were similar between unaged and aged specimens, and neutron irradiation decreased the fracture toughness significantly. The fracture toughness of CF-8 was reduced after thermal aging, and declined further after irradiation. It appears that while lowering ferrite content may help reduce the tendency of thermal aging embrittlement, it is not very effective to mitigate irradiation-induced embrittlement. Under a combined condition of thermal aging and irradiation, neutron irradiation plays a dominant role in causing embrittlement in CASS alloys.

Irradiation techniques at BR2 reactor

International Nuclear Information System (INIS)

Hebel, W.

1978-01-01

Since 1963 the material testing reactor BR2 at Mol is operated for the realisation of numerous research programs and experiments on the behavior of materials under nuclear radiation and in particular under intensive neutron exposure. During this period special irradiation techniques and experimental devices were developed according to the desiderata of the different experiments and to the irradiation possibilities offered at BR2. The design and the operating characteristics of quite a number of those irradiation rigs of proven reliability may be used or can be made available for new irradiation experiments. A brief description is given of some typical irradiation devices designed and constructed by CEN/SCK, Technology and Energy Dpt. They are compiled according to their main use for the different research and development programs realized at BR2. Their eventual application however for different objectives could be possible. A final chapter summarizes the principal irradiation conditions offered by BR2 reactor. (author)

Irradiation devices at the upgraded research reactor BER II

International Nuclear Information System (INIS)

Gawlik, D.; Robertson, T.

1992-06-01

An overview is given of those properties of the BER II research reactor which are important for carrying out irradiation experiments. The subsequent section describes the irradiation devices currently installed in the reactor, or which are under construction, and some of the experiments which can be conducted using them. The field of application of these experiments extends from the study of the metabolism of trace elements in man, employing a highly sensitive element analysis, via radiation damage of high-tech materials, to the identification of paintings of the old masters. The report concludes with a review of the technical details of the irradiation devices, giving information of interest for potential users. (orig.)

Technical oversight for installation of TNX piezometers, Final Report

Energy Technology Data Exchange (ETDEWEB)

Pidcoe, W.W. Jr. [Westinghouse Savannah River Company, Aiken, SC (United States)

1997-06-05

Science Applications International Corporation was tasked under subcontract C002025P to provide technical oversight for the drilling of one pilot borehole, and the drilling and installation of five piezometers in the TNX Area Swamp. The work was performed in accordance with the Statement of Work in Task Order Proposal No. ER39-129 dated August 6, 1996. This report describes the activities associated with the performance of the task.

Food irradiation newsletter. V. 17, no. 2

International Nuclear Information System (INIS)

1993-07-01

This issue of the Food Irradiation Newsletter includes reports of a number of activities of the Food Preservation Section of the FAO/IAEA from the final quarter of 1992 to the middle of 1993. In addition there is a summary of food irradiation activities in the USA, an excerpt from the Official Gazette of the French Republic concerning the use of ionizing radiation to treat camembert made from raw milk, and a discussion of the potential for the application of food irradiation in Russia

Volatiles combustion in fluidized beds. Final technical report, 4 September 1992--4 June 1995

Energy Technology Data Exchange (ETDEWEB)

Pendergrass, R.A. II; Raffensperger, C.; Hesketh, R.P.

1996-02-29

The goal of this project is to investigate the conditions in which volatiles will burn within both the dense and freeboard regions of fluidized beds. Experiments using a fluidized bed operated at incipient fluidization are being conducted to characterize the effect of particle surface area, initial fuel concentration, and particle type on the inhibition of volatiles within a fluidized bed. A review of the work conducted under this grant is presented in this Final Technical Report. Both experimental and theoretical work have been conducted to examine the inhibition of the combustion by the fluidized bed material, sand. It has been shown that particulate phase at incipient fluidization inhibits the combustion of propane by free radical destruction at the surface of sand particles within the particulate phase. The implications of these findings is that at bed temperatures lower than the critical temperatures, gas combustion can only occur in the bubble phase or at the top surface of a bubbling fluidized bed. In modeling fluidized bed combustion this inhibition by the particulate phase should be included.

Commercial storage and marketing trials of irradiated Onions

International Nuclear Information System (INIS)

Nouchpramool, K.; Charoen, S.; Prachasitthisak, Y.

1997-06-01

Pilot scale storage tests were carried out in co-operation with commercial onions traders in the years 1986 and 1987 to evaluate the efficacy of irradiation for sprout inhibition of onions under actual commercial stored in commercial cold storage at 1-10 degrees C and 70-90% relative humidity. The results show that irradiation reduce sprouting in onions by 11 and 40 per cent and weight loss by 3 and 5 per cent after 5 and 6 months of storage, respectively. Storage losses are minimum when radiation is applied within two weeks of harvest. A maximum storage life of six months as against five months for controls is attained. Post cold storage life at ambient temperature for irradiated onions after withdrawal from cold storage is one week longer than that of non-irradiated controls. The radio inhibition process is technically feasible and economically justified as a profit can be made during the extended storage period. Marketing trials of irradiated onions conducted during and after termination of storage revealed no adverse comments from consumers and retailers/wholesalers. Wholesalers.retailers and consumers preferred irradiated onions because of their better physical quality and longer marketable life

Irradiation testing of coated particle fuel at Hanaro

International Nuclear Information System (INIS)

Goo Kim, Bong; Sung Cho, Moo; Kim, Yong Wan

2014-01-01

TRISO-coated particle fuel is developing to support development of VHTR in Korea. From August 2013, the first irradiation testing of coated particle fuel was begun to demonstrate and qualify TRISO fuel for use in VHTR in the HANARO at KAERI. This experiment is currently undergoing under the atmosphere of a mixed inert gas without on-line temperature monitoring and control combined with on-line fission product monitoring of the sweep gas. The irradiation device contains two test rods, one contains nine fuel compacts and the other five compacts and eight graphite specimens. Each compact has 263 coated particles. After a peak burn-up of about 4 at% and a peak fast neutron fluence of about 1.7 x 10 21 n/cm 2 , PIE will be carried out at KAERI's Irradiated Material Examination Facility. This paper is described characteristics of coated particle fuel, the design of test rod and irradiation device for coated particle fuel, discusses the technical results for irradiation testing at HANARO. (authors)

Development of the biosphere code BIOMOD: final report

International Nuclear Information System (INIS)

Kane, P.

1983-05-01

Final report to DoE on the development of the biosphere code BIOMOD. The work carried out under the contract is itemised. Reference is made to the six documents issued along with the final report. These consist of two technical notes issued as interim consultative documents, a user's guide and a programmer's guide to BIOMOD, a database description, program test document and a technical note entitled ''BIOMOD - preliminary findings''. (author)

Handbook for the experimental open-pool irradiation facility of the Letaba Co-operative Limited, at Tzaneen

International Nuclear Information System (INIS)

Du Plessis, T.A.; Entwistle, B.; Gawn, P.D.

1978-03-01

A detailed technical description of the experimental food irradiator which was jointly established by the Atomic Energy Board and the Letaba Co-operative Limited at Tzaneen, is presented. The commissioning of the irradiator, the dosimetry and plant operating procedures are discussed. Attention is paid to the regulatory control of such an irradiator and a hazards evaluation and appropriate action to be taken is provided [af

Quality control in the commerce of irradiated foods

International Nuclear Information System (INIS)

Bustos R, M.E.

2000-01-01

In spite of an irradiated food is innocuous for health and that the irradiation process offers great advantages as conservation and hygiene method and it has been recognised by the Agriculture and Health International organizations and although the adequate equipment exists to make this treatment in the majority of countries, an international trade of irradiated foods has not been established and it is that it has to be required that the quality control of the treatment should be regulated by the corresponding authorities and it also should be harmonized with other countries for the commercial interchange. Owing to up to present an identification method of irradiated foods which is validated, the unique quality control for irradiated foods is realized in the irradiation plant, measuring the absorbed dose in products, using dosimetric systems justly calibrated and standardized to be used the adequate for the type of product and dose level which is wanted to be measured for foods mainly for quarantine treatment which is very important to determine that any part of the irradiation system has reached the minimum dose to obtain the technical effect which is desired and that it does not exceed the maximum dose for that the product quality not to be altered. (Author)

Irradiation Testing of TRISO-Coated Particle Fuel in Korea

International Nuclear Information System (INIS)

Kim, Bong Goo; Yeo, Sunghwan; Jeong, Kyung-Chai; Eom, Sung-Ho; Kim, Yeon-Ku; Kim, Woong Ki; Lee, Young Woo; Cho, Moon Sung; Kim, Yong Wan

2014-01-01

In Korea, coated particle fuel is being developed to support development of a VHTR. At the end of March 2014, the first irradiation test in HANARO at KAERI to demonstrate and qualify TRISO-coated particle fuel for use in a VHTR was terminated. This experiment was conducted in an inert gas atmosphere without on-line temperature monitoring and control, or on-line fission product monitoring of the sweep gas. The irradiation device contained two test rods, one has nine fuel compacts and the other five compacts and eight graphite specimens. Each compact contains about 260 TRISO-coated particles. The duration of irradiation testing at HANARO was about 135 full power days from last August 2013. The maximum average power per particle was about 165 mW/particle. The calculated peak burnup of the TRISO-coated fuel was a little less than 4 atom percent. Post-irradiation examination is being carried out at KAERI’s Irradiated Material Examination Facility beginning in September of 2014. This paper describes characteristics of coated particle fuel, the design of the test rod and irradiation device for this coated particle fuel, and discusses the technical results of irradiation testing at HANARO. (author)

A Detector for Combined SPECT/CT. Final Technical Report

International Nuclear Information System (INIS)

Vivek Nagarkar

2006-01-01

The goal of the Phase I research was to demonstrate the feasibility of developing a high performance SPECT/CT detector module based on a combination of microcolumnar CsI(Tl) scintillator coupled to an EMCCD readout. We are very pleased to report that our Phase I research has demonstrated the technical feasibility of our approach with a very high degree of success. Specifically, we were able to implement a back-thinned EMCCD with a fiberoptic window which was successfully used to demonstrate the feasibility of near simultaneous radionuclide/CT using the proposed concept. Although significantly limited in imaging area (24 x 24 mm 2 ) and pixel resolution (512 x 512), this prototype has shown exceptional capabilities such as a single optical photon sensitivity, very low noise, an intrinsic resolution of 64 (micro)m for radionuclide imaging, and a resolution in excess of 10 lp/mm for x-ray imaging. Furthermore, the combination of newly developed, thick, microcolumnar CsI and an EMCCD has shown to be capable of operating in a photon counting mode, and that the position and energy information obtained from these data can be used to improve resolution in radionuclide imaging. Finally, the prototype system has successfully been employed for near simultaneous SPECT/CT imaging using both, 125 I and 99m Tc radioisotopes. The tomographic reconstruction data obtained using a mouse heart phantom and other phantoms clearly demonstrate the feasibility and efficacy of the detector in small animal research. The following were the objectives specified in the Phase I proposal: (1) In consultation with Professor Hasegawa, develop specifications for the Phase I/Phase II prototype detector; (2) Modify current vapor deposition protocols to fabricate ∼2 mm thick microcolumnar CsI(Tl) scintillators with excellent columnar structure, high light yield, and high spatial resolution; (3) Perform detailed characterization of the film morphology, light output, and spatial resolution, and use

Nasopharyngeal irradiation treatment of hyperplastic adenoids

International Nuclear Information System (INIS)

Pratt, L.W.

1981-01-01

Radiotherapy treatment in childhood is an important cause of thyroid cancer. In the 1930 to 1950 era, radium irradiation of the nasopharynx was used to control hyperplastic adenoids. Because of the technical characteristics of this applicator, sufficient radiation was not applied to the thyroid by this technique to stimulate the development of thyroid malignancies. No malignancies have been reported thus far as a result of this treatment

Final Technical Report: "Representing Endogenous Technological Change in Climate Policy Models: General Equilibrium Approaches"

Energy Technology Data Exchange (ETDEWEB)

Ian Sue Wing

2006-04-18

The research supported by this award pursued three lines of inquiry: (1) The construction of dynamic general equilibrium models to simulate the accumulation and substitution of knowledge, which has resulted in the preparation and submission of several papers: (a) A submitted pedagogic paper which clarifies the structure and operation of computable general equilibrium (CGE) models (C.2), and a review article in press which develops a taxonomy for understanding the representation of technical change in economic and engineering models for climate policy analysis (B.3). (b) A paper which models knowledge directly as a homogeneous factor, and demonstrates that inter-sectoral reallocation of knowledge is the key margin of adjustment which enables induced technical change to lower the costs of climate policy (C.1). (c) An empirical paper which estimates the contribution of embodied knowledge to aggregate energy intensity in the U.S. (C.3), followed by a companion article which embeds these results within a CGE model to understand the degree to which autonomous energy efficiency improvement (AEEI) is attributable to technical change as opposed to sub-sectoral shifts in industrial composition (C.4) (d) Finally, ongoing theoretical work to characterize the precursors and implications of the response of innovation to emission limits (E.2). (2) Data development and simulation modeling to understand how the characteristics of discrete energy supply technologies determine their succession in response to emission limits when they are embedded within a general equilibrium framework. This work has produced two peer-reviewed articles which are currently in press (B.1 and B.2). (3) Empirical investigation of trade as an avenue for the transmission of technological change to developing countries, and its implications for leakage, which has resulted in an econometric study which is being revised for submission to a journal (E.1). As work commenced on this topic, the U.S. withdrawal

Effect of irradiation on foodstuffs Pt. 4

International Nuclear Information System (INIS)

Kluender, U.; Boegl, W.

1980-01-01

In the present study of the relevant literature the results of irradiation experiments with 32 foodstuffs have been compiled and discussed. This study is intented to give a survey on chemical changes in irradiated food, and neither microbiological nor toxicological and physiological aspects were taken into account. The results published by the authors of the original papers have been compiled in form of a dictionary which contains all important data such as radiation source, irradiation conditions, treatment and characteristics of the sample, investigation methods, results of the chemical and organoleptical changes etc. In addition, the effects of irradiation both on individual food substances and individual groups of foodstuffs have been summarized. Furthermore, the effects of irradiation on sensory characteristics and the atmospheric influence during irradiation are given seperately. The last chapter contains a comparison between the chemical changes of food due to irradiation treatment and those caused by conventional methods. The final discussion of the results will be published seperately. (orig./MG) [de

Site Specific Microbeam Irradiation: Defining a Bystander Effect. Final Technical Report

International Nuclear Information System (INIS)

Brenner, David J.

2003-01-01

There is evidence that low-energy x-rays as used in mammography have an increased biological effectiveness relative to higher-energy photons. However, the RBE values are not large, probably less than 2. Thus it is unlikely that the radiation risk alone could prove to be a ''show stopper'' regarding screening mammography because, for older women, the benefit is likely to considerably outweigh the radiation risk. Nevertheless, the RBE for low-energy x-rays might reasonably be taken into account when assessing the recommended age to commence such annual screening

Virginia Solar Pathways Project Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Bond, Katharine; Cosby, Sarah

2018-03-28

This Report provides a technical review of the final results of a funding award to Virginia Electric and Power Company (Dominion Energy Virginia (DEV) or the Company) for a project under the U.S. Department of Energy’s Solar Energy Technologies Office. The three-year project was formally known as the Virginia Solar Pathways Project (VSPP or the Project). The purpose of the VSPP was to develop a collaborative utility-administered solar strategy (Solar Strategy) for DEV’s service territory in the Commonwealth that could serve as a replicable model for other states with similar policy environments. The U.S. Department of Energy (DOE) funding award enabled DEV to take a focused approach to developing the Solar Strategy for its Virginia service territory. The structure and funding from the DOE award also facilitated valuable input from a formal stakeholder team convened to serve as advisors (Advisory Team) to the VSPP and contribute their perspectives and expertise to both the analysis and strategy development aspects of the Project. The development of the Solar Strategy involved three main goals: • Establish a policy and program framework that would integrate existing solar programs with new options appropriate for the Commonwealth’s policy environment and broader economic development objectives; • Promote wider deployment of solar within a low retail electric rate environment; and • Serve as a sustainable, utility-administered solar model that could be replicated in other states with similar policy environments, including, but not limited to, the entire Southeast region. In support of the VSPP goals, the Project Team commissioned four studies to support the Solar Strategy development. Two studies, completed by Navigant Consulting, focused on the integration of solar into the electric grid. The first solar integration study focused on integration of solar into the distribution grid where the utility system directly connects to and serves end-use customers

FOREX trading strategy formation using technical analysis

OpenAIRE

Klimavičius, Domas

2010-01-01

FOREX technical analysis indicators, their characteristics and capabilities are researched in this final master thesis. The main goal of this thesis is to determine if technical analysis indicators can recognise patterns in price movements and if they can predict future price movement. The first part of the thesis presents with FOREX theoretical aspects, its characteristics and participants. In the second part of the thesis FOREX analysis tools are overviewed, focusing on technical analysis. ...

Food Irradiation Newsletter. V. 16, no. 1

International Nuclear Information System (INIS)

1992-05-01

This newsletter contains a report on the final FAO/IAEA Research Coordination Meeting (RCM) on the use of irradiation to control the infectivity of food-borne parasites, held in Mexico City in June, 1991, and a brief summary of the second FAO/IAEA RCM on the Asian Regional Cooperative Project on food irradiation, with emphasis on process control and acceptance. The workshops and training courses held between September and December 1991 are presented, and a short article reports the opening of the USA's first commercial food irradiator and describes the initial public reaction

Acceptance of food irradiation in western markets

Energy Technology Data Exchange (ETDEWEB)

Ting, H H [PURIDEC Irradiation Technologies, Buckinghamshire, England (United Kingdom)

1997-12-31

This paper reviews the status and acceptance of food irradiation worldwide, focusing on Europe and the United States. Today no less than 38 countries including the USA and 14 European countries, have approved the irradiation of food. Across Europe there is a very wide variation, with a variety of foods being irradiated and eaten in Belgium and France but a total ban on food irradiation in Germany. Progress towards a directive harmonising the position across all countries in the European Union is slow. In the USA there is a growing awareness of the advantages of using food irradiation to combat the increasing risk of the food-borne diseases, and media coverage and consumer attitudes are considerably more favourable than previously. The use of irradiation instead of pesticides for spice treatment is gaining acceptance within the North American spice industry and the NA meat industry is recognising the potential of food irradiation as one way of meeting its obligations under the new HACCP regulations. Food irradiation is also being seriously considered as an alternative to the use of methyl bromide for quarantine treatment of fruit and vegetables. The establishment of the World Trade Organisation in 1995 to enforce various agreements concluded during the GATT Uruguay Round is expected to impact trade liberalisation. In particular the agreements pertaining to the Application of Sanitary and Phytosanitary Measures (SPS) and on Technical Barriers to Trade (TBT) have particular reference to track in irradiated food. In this respect, it is particularly important for potential training partners (food producing countries) to ensure that they have domestic approvals in place for any irradiated foods they provide to western countries. (author). countries. (author).

Acceptance of food irradiation in western markets

International Nuclear Information System (INIS)

Ting, H.H.

1996-01-01

This paper reviews the status and acceptance of food irradiation worldwide, focusing on Europe and the United States. Today no less than 38 countries including the USA and 14 European countries, have approved the irradiation of food. Across Europe there is a very wide variation, with a variety of foods being irradiated and eaten in Belgium and France but a total ban on food irradiation in Germany. Progress towards a directive harmonising the position across all countries in the European Union is slow. In the USA there is a growing awareness of the advantages of using food irradiation to combat the increasing risk of the food-borne diseases, and media coverage and consumer attitudes are considerably more favourable than previously. The use of irradiation instead of pesticides for spice treatment is gaining acceptance within the North American spice industry and the NA meat industry is recognising the potential of food irradiation as one way of meeting its obligations under the new HACCP regulations. Food irradiation is also being seriously considered as an alternative to the use of methyl bromide for quarantine treatment of fruit and vegetables. The establishment of the World Trade Organisation in 1995 to enforce various agreements concluded during the GATT Uruguay Round is expected to impact trade liberalisation. In particular the agreements pertaining to the Application of Sanitary and Phytosanitary Measures (SPS) and on Technical Barriers to Trade (TBT) have particular reference to track in irradiated food. In this respect, it is particularly important for potential training partners (food producing countries) to ensure that they have domestic approvals in place for any irradiated foods they provide to western countries. (author). countries. (author)

Food irradiation

International Nuclear Information System (INIS)

Roberts, P.B.

1997-01-01

Food can be provided with extra beneficial properties by physical processing. These benefits include a reduced possibility of food poisoning, or an increased life of the food. We are familiar with pasteurisation of milk, drying of vegetables, and canning of fruit. These physical processes work because the food absorbs energy during treatment which brings about the changes needed. The energy absorbed in these examples is heat energy. Food irradiation is a less familiar process. It produces similar benefits to other processes and it can sometimes be applied with additional advantages over conventional processing. For example, because irradiation causes little heating, foods may look and taste more natural. Also, treatment can take place with the food in its final plastic wrappers, reducing the risk of re-contamination. (author). 1 ref., 4 figs., 1 tab

Final Technical Report for Year 5 Early Career Research Project "Viscosity and equation of state of hot and dense QCD matter"

Energy Technology Data Exchange (ETDEWEB)

Molnar, Denes [Purdue Univ., West Lafayette, IN (United States)

2016-05-25

The Section below summarizes research activities and achievements during the fifth (last) year of the PI’s Early Career Research Project (ECRP). Unlike the first four years of the project, the last year was not funded under the American Recovery and Reinvestment Act (ARRA). The ECRP advanced two main areas: i) radiative 3 ↔ 2 radiative transport, via development of a new computer code MPC/Grid that solves the Boltzmann transport equation in full 6+1D (3X+3V+time); and ii) application of relativistic hydrodynamics, via development of a self-consistent framework to convert viscous fluids to particles. In Year 5 we finalized thermalization studies with radiative gg ↔ ggg transport (Sec. 1.1.1) and used nonlinear covariant transport to assess the accuracy of fluid-to-particle conversion models (Sec. 1.1.2), calculated observables with self-consistent fluid-to-particle conversion from realistic viscous hydrodynamic evolution (Secs. 1.2.1 and 1.2.2), extended the covariant energy loss formulation to heavy quarks (Sec. 1.4.1) and studied energy loss in small systems (Sec. 1.4.2), and also investigated how much of the elliptic flow could have non-hydrodynamic origin (Sec 1.3). Years 1-4 of the ECRP were ARRA-funded and, therefore, they have their own report document ’Final Technical Report for Years 1-4 of the Early Career Research Project “Viscosity and equation of state of hot and dense QCD matter”’ (same award number DE-SC0004035). The PI’s group was also part of the DOE JET Topical Collaboration, a multi-institution project that overlapped in time significantly with the ECRP. Purdue achievements as part of the JET Top- ical Collaboration are in a separate report “Final Technical Report summarizing Purdue research activities as part of the DOE JET Topical Collaboration” (award DE-SC0004077).

75 FR 33682 - Export Administration Regulations; Technical Amendments

Science.gov (United States)

2010-06-15

...-01] RIN 0694-AE93 Export Administration Regulations; Technical Amendments AGENCY: Bureau of Industry... Bureau of Industry and Security (BIS) makes a technical amendment to the Export Administration... review of final decisions and orders issued in BIS export control administrative enforcement proceedings...

Health care fraud and abuse data collection program: technical revisions to Healthcare Integrity and Protection Data Bank data collection activities. Final rule.

Science.gov (United States)

2004-09-21

The rule finalizes technical changes to the Healthcare Integrity and Protection Data Bank (HIPDB) data collection reporting requirements by clarifying the types of personal numeric identifiers that may be reported to the data bank in connection with adverse actions. The rule clarifies that in lieu of a Social Security Number (SSN), an individual taxpayer identification number (ITIN) may be reported to the data bank when, in those limited situations, an individual does not have an SSN.

Food irradiation; Global aspects and future prospects

Energy Technology Data Exchange (ETDEWEB)

Matsuyama, Akira (Tokyo Univ. of Agriculture (Japan). Nodai Research Institute)

1990-07-01

This paper reviews researches, commentaries, and conference and public records of food irradiation, published mainly during the period 1987-1989, focusing on the current conditions of food irradiation that may pose not only scientific or technologic problems but also political issues or consumerism. Approximately 50 kinds of food, although not enough to fill economic benefit, are now permitted for food irradiation in the world. Consumerism is pointed out as the major factor that precludes the feasibility of food irradiation in the world. In the United States, irradiation is feasible only for spices. Food irradiation has already been feasible in France, Hollands, Belgium, and the Soviet Union; has under consideration in the Great Britain, and has been rejected in the West Germany. Although the feasibility of food irradiation is projected to increase gradually in the future, commercial success or failure depends on the final selection of consumers. In this respect, the role of education and public information are stressed. Meat radicidation and recent progress in the method for detecting irradiated food are referred to. (N.K.) 128 refs.

Food Preservation by Irradiation. Vol. II. Proceedings of an International Symposium on Food Preservation by Irradiation

International Nuclear Information System (INIS)

1978-01-01

, as well as on the public health acceptability of a number of irradiated food items. These matters had been reported in WHO Technical Reports Series No.604, Wholesomeness of Irradiated Food, published in Geneva, 1977. (3) The Joint FAO/WHO Food Standards Programme, through the Codex Alimentarius, had examined food irradiation and developed a proposed General Standard on Irradiated Foods and a proposed Code of Practice for the Operation of Radiation Facilities used for the Treatment of Foods at step 5 of the 9-10 step procedure of the Codex. (4) FAO and the IAEA were about to join forces with the Government of the Netherlands in establishing an International Facility for Food Irradiation Technology at Wageningen for the purposes of technological and economic training and research in food irradiation. Sessions of the Symposium dealt with such topics as the control of animal infestation, toxicological studies, public health aspects and economics, and many papers were concerned with chemical changes in irradiated foods and with the control of microbial spoilage. The present Proceedings contain the papers given and the ensuing discussions, including the extensive round-table discussion on a plan of action for the future. The order of publication of the papers does not strictly follow that of presentation at the Symposium where, for technical reasons, it was not always possible to preserve the logical sequence. Viewed against the new developments recorded here, the outlook for the food irradiation community is encouraging, and the tasks ahead appear less formidable. The sponsoring organizations hope that the publication of this material will be a useful contribution towards accelerated progress in the practical application of food processing by irradiation

Food Preservation by Irradiation. Vol. I. Proceedings of an International Symposium on Food Preservation by Irradiation

International Nuclear Information System (INIS)

1978-01-01

studies, as well as on the public health acceptability of a number of irradiated food items. These matters had been reported in WHO Technical Reports Series No.604, Wholesomeness of Irradiated Food, published in Geneva, 1977. (3) The Joint FAO/WHO Food Standards Programme, through the Codex Alimentarius, had examined food irradiation and developed a proposed General Standard on Irradiated Foods and a proposed Code of Practice for the Operation of Radiation Facilities used for the Treatment of Foods at step 5 of the 9 - 10 step procedure of the Codex. (4) FAO and the IAEA were about to join forces with the Government of the Netherlands in establishing an International Facility for Food Irradiation Technology at Wageningen for the purposes of technological and economic training and research in food irradiation. Sessions o f the Symposium dealt with such topics as the control of animal infestation, toxicological studies, public health aspects and economics, and many papers were concerned with chemical changes in irradiated foods and with the control o f microbial spoilage. The present Proceedings contain the papers given and the ensuing discussions, including the extensive round-table discussion on a plan of action for the future. The order of publication of the papers does not strictly follow that of presentation at the Symposium where, for technical reasons, it was not always possible to preserve the logical sequence. Viewed against the new developments recorded here, the outlook for the food irradiation community is encouraging, and the tasks ahead appear less formidable. The sponsoring organizations hope that the publication of this material will be a useful contribution towards accelerated progress in the practical application of food processing by irradiation

Status and possible prospects of an international fusion materials irradiation facility

International Nuclear Information System (INIS)

Cozzani, F.

1999-01-01

Structural materials for future DT fusion power reactors will have to operate under intense neutron fields with energies up to 14 MeV and fluences in the order of 2 MW/m 2 per year. As environmental acceptability, safety considerations and economic viability will be ultimately the keys to the widespread introduction of fusion power, the development of radiation-resistant and low activation materials would contribute significantly to fusion development. For this purpose, testing of materials under irradiation conditions close to those expected in a fusion power station would require the availability, in an appropriate time framework, of an intense, high-energy neutron source. Recent advances in linear accelerator technology, in small specimens testing technology, and in the comprehension of damage phenomena, lead to the conclusion that an accelerator-based D-Li neutron source, with beam energy variability, would provide the most realistic option for a fusion materials testing facility. Under the auspices of the IEA, an international effort (EU, Japan, US, RF) to carry out the conceptual design activities (CDA) of an international fusion materials irradiation facility (IFMIF), based on the D-Li concept, have been carried out successfully. A final conceptual design report was produced at the end of 1996. A phase of conceptual design evaluation (CDE), presently underway, is extending and further refining some of the conceptual design details of IFMIF. The results indicate that an IFMIF-class installation would be technically feasible and could meet its mission objectives. However, a suitable phase of Engineering Validation, to carry out some complementary R and D and prototyping, would still be needed to resolve a few key technical uncertainties before the possibility to proceed toward detailed design and construction could be explored. (orig.)

Monitoring pathogens from irradiated agriculture products

International Nuclear Information System (INIS)

Butterweck, J.S.

1990-01-01

The final food and environmental safety assessment of agriculture product irradiation can only be determined by product history. Product history will be used for future research and development, regulations, commercial practices and implementation of agriculture and food irradiation on a regional basis. The commercial irradiator treats large varieties and amounts of products that are used in various environments. it, in time, will generate a large data base of product history. Field product monitoring begins when food irradiation progresses from the pilot/demonstration phase to the commercial phase. At that time, it is important that there be in place a monitoring system to collect and analyze field data. The systems managers, public health authorities and exotic disease specialists will use this information to assess the reduction of food pathogens on the populace and the environment. (author)

Design, fabrication and installation of irradiation facilities

Energy Technology Data Exchange (ETDEWEB)

Sim, Bong Shick; Kim, Y. S.; Lee, C. Y. and others

1999-03-01

The principal contents of this project are to design, fabricate and install the steady-state fuel test loop in HANARO for nuclear technology development. Procurement and fabrication of main equipment, licensing and technical review for fuel test loop have been performed during 2 years(1997, 1998) for this project. Following contents are described in the report. - Procurement and fabrication of the equipment, piping for OPS - IPS manufacture - License - Technical review and evaluation of the FTL facility. As besides, as these irradiation facilities will be installed in HANARO, review of safety concern, discussion with KINS for licensing and review ofHANARO interface have been performed respectively. (author)

Progress of food irradiation in the United States

International Nuclear Information System (INIS)

Derr, D.D.; Engeljohn, D.L.; Griffin, R.L.

1995-01-01

Irradiated foods have not yet made a significant impact in the United States marketplace. What progress has occurred to facilitate their commercialization? Irradiated produce has been sold in small quantities since 1992 and irradiated poultry was introduced in the marketplace in 1993. Federal inspection of irradiated commodities has settled into a regular routine. What must occur to further expand irradiated foods in the marketplace? Petitions to permit irradiation of red meats and seafood are being considered by the Food and Drug Administration (FDA) and a petition to permit the irradiation of shell eggs is being prepared for submission to FDA. In addition, the U.S. Department of Agriculture (USDA) has accelerated efforts to develop the policies and regulatory structure needed to facilitate the approval of new irradiation treatments for imported plant products regulated by quarantine. When will greater commercialization occur? More positive coverage to food irradiation in recent months by both the trade and popular press indicates a change in attitude towards irradiated foods by both consumers and the food industry. Finally, actual consumer response to available irradiated foods casts a favorable light on the potential for increased marketing of value-added irradiated foods. (Author)

The evaluation of a framework for measuring the non-technical ward round skills of final year nursing students: An observational study.

Science.gov (United States)

Murray, Kara; McKenzie, Karen; Kelleher, Michael

2016-10-01

The importance of non-technical skills (NTS) to patient outcomes is increasingly being recognised, however, there is limited research into how such skills can be taught and evaluated in student nurses in relation toward rounds. This pilot study describes an evaluation of a NTS framework that could potentially be used to measure ward round skills of student nurses. The study used an observational design. Potential key NTS were identified from existing literature and NTS taxonomies. The proposed framework was then used to evaluate whether the identified NTS were evident in a series of ward round simulations that final year general nursing students undertook as part of their training. Finally, the views of a small group of qualified nurse educators, qualified nurses and general nursing students were sought about whether the identified NTS were important and relevant to practice. The proposed NTS framework included seven categories: Communication, Decision Making, Situational Awareness, Teamwork and Task Management, Student Initiative and Responsiveness to Patient. All were rated as important and relevant to practice. The pilot study suggests that the proposed NTS framework could be used as a means of evaluating student nurse competencies in respect of many non-technical skills required for a successful ward round. Further work is required to establish the validity of the framework in educational settings and to determine the extent to which it is of use in a non-simulated ward round setting. Copyright © 2016 Elsevier Ltd. All rights reserved.

Irradiation-induced permeability in pyrocarbon coatings. Final report of work conducted under PWS FD-12

International Nuclear Information System (INIS)

Kania, M.J.; Thiele, B.A.; Homan, F.J.

1982-10-01

Two US irradiation experiments were planned to provide information to supplement data from the German program on irradiation-induced permeability in pyrocarbon coatings. Hopefully, the data from both programs could be combined to define the onset of neutron-induced permeability in a variety of Biso coatings produced with different process variables (coating temperature, coating gases, and coating rates). The effort was not successful. None of the preirradiation characterization procedures were able to adequately predict irradiation performance. A large amount of within-batch scatter was observed in the fission gas and cesium release data along with significant within-batch variation in coating properties. Additional preirradiation characterization might result in a procedure that could successfully predict irradiation performance, but little can be done about the within-batch variation in coating properties. This variation is probably the result of random movement of particles within the coating furnace during pyrocarbon deposition. 19 figures, 4 tables

The establishment of good irradiation practice for insect disinfestation of cereal grain products

International Nuclear Information System (INIS)

Lin Yin; Liu Hongyue; Li Xiangling; Shi Peixin

2001-01-01

According to the reference data and test results, the parameters and technicality of good irradiation practice (GIP) were established as follows: (1) the moisture level of grain products should be < 12% for pre-irradiation treatment of grains, and pupae and adult stages insects should not exist in the products; (2) grain products should be irradiated immediately after packing; (3) the minimum effective dose for insect disinfestation is 0.3 kGy and the maximum tolerant doses for different cereal grains products are 0.5 ∼ 0.8 kGy. (authors)

Final Technical Report Radiation Hard Tight Pitch GaInP SPAD Arrays for High Energy Physics

Energy Technology Data Exchange (ETDEWEB)

Harmon, Eric

2018-01-26

The specialized photodetectors used in high energy physics experiments often need to remain extremely sensitive for years despite radiation induced damage caused by the constant bombardment of high energy particles. To solve this problem, LightSpin Technologies, Inc. in collaboration with Prof. Bradley Cox and the University of Virginia is developing radiation-hard GaInP photodetectors which are projected to be extraordinarily radiation hard, theoretically capable of withstanding a 100,000-fold higher radiation dose than silicon. In this Phase I SBIR project, LightSpin investigated the performance and radiation hardness of fifth generation GaInP SPAD arrays. These fifth generation devices used a new planar processing approach that enables very tight pitch arrays to be produced. High performance devices with SPAD pitches of 11, 15, and 25 μm were successfully demonstrated, which greatly increased the dynamic range and maximum count rate of the devices. High maximum count rates are critical when considering radiation hardness, since radiation damage causes a proportional increase in the dark count rate, causing SPAD arrays with low maximum count rates (large SPAD pitches) to fail. These GaInP SPAD array Photomultiplier Chips™ were irradiated with protons, electrons, and neutrons. Initial irradiation results were disappointing, with the post-irradiation devices exhibiting excessively high dark currents. The degradation was traced to surface leakage currents that were largely eliminated through the use of trenches etched around the exterior of the Photomultiplier Chip™ (not between SPAD elements). A second round of irradiations on Photomultiplier Chips™ with trenches proved substantially more successful, with post-irradiation dark currents remaining relatively low, though dark count rates were observed to increase at the highest doses. Preliminary analysis of the post-irradiation devices is promising … many of the irradiated Photomultiplier Chips™ still

Preliminary irradiation test results from the Yankee Atomic Electric Company reactor vessel test irradiation program

International Nuclear Information System (INIS)

Biemiller, E.C.; Fyfitch, Stephen; Campbell, C.A.

1994-01-01

The Yankee Atomic Electric Company test irradiation program was implemented to characterize the irradiation response of representative Yankee Rowe reactor vessel beltline plate materials and to remove uncertainties in the analysis of existing irradiation data on the Yankee Rowe reactor vessel steel. Plate materials each containing 0.24 w/o copper, but different nickel contents at 0.63 w/o and 0.19 w/o, were heat treated to simulate the Yankee vessel heat treatment (austenitized at 982 o C (1800 o F)) and to simulate Regulatory Guide 1.99 database materials (austenitized at 871 o C (1600 o F)). These heat treatments produced different microstructures so the effect of microstructure on irradiation damage sensitivity could be tested. Because the nickel content of the test plates varied and the copper level was constant, the effect of nickel on irradiation embrittlement was also tested. Correlation monitor material, HSST-02, was included in the program to benchmark the Ford Nuclear Reactor (University of Michigan Test Reactor) which had never been used before for this type of irradiation program. Materials taken from plate surface locations (versus 1/4 T) were included to test whether or not the improved toughness properties of the plate surface layer, resulting from the rapid quench, are maintained after irradiation. If the improved properties are maintained, pressurized thermal shock calculations could utilize this margin. Finally, for one experiment, irradiations were conducted at two irradiation temperatures (260 o C and 288 o C) to determine the effect of irradiation temperature on embrittlement. (Author)

Dosimetry computer module of the gamma irradiator of ININ

International Nuclear Information System (INIS)

Ledezma F, L. E.; Baldomero J, R.; Agis E, K. A.

2012-10-01

This work present the technical specifications for the upgrade of the dosimetry module of the computer system of the gamma irradiator of the Instituto Nacional de Investigaciones Nucleares (ININ) whose result allows the integration and consultation of information in industrial dosimetry subject under an outline client-server. (Author)

High-Efficiency Nitride-Based Solid-State Lighting. Final Technical Progress Report

International Nuclear Information System (INIS)

Paul T. Fini; Shuji Nakamura

2005-01-01

In this final technical progress report we summarize research accomplished during Department of Energy contract DE-FC26-01NT41203, entitled ''High-Efficiency Nitride-Based Solid-State Lighting''. Two teams, from the University of California at Santa Barbara (Principle Investigator: Dr. Shuji Nakamura) and the Lighting Research Center at Rensselaer Polytechnic Institute (led by Dr. N. Narendran), pursued the goals of this contract from thin film growth, characterization, and packaging/luminaire design standpoints. The UCSB team initially pursued the development of blue gallium nitride (GaN)-based vertical-cavity surface-emitting lasers, as well as ultraviolet GaN-based light emitting diodes (LEDs). In Year 2, the emphasis shifted to resonant-cavity light emitting diodes, also known as micro-cavity LEDs when extremely thin device cavities are fabricated. These devices have very directional emission and higher light extraction efficiency than conventional LEDs. Via the optimization of thin-film growth and refinement of device processing, we decreased the total cavity thickness to less than 1 (micro)m, such that micro-cavity effects were clearly observed and a light extraction efficiency of over 10% was reached. We also began the development of photonic crystals for increased light extraction, in particular for so-called ''guided modes'' which would otherwise propagate laterally in the device and be re-absorbed. Finally, we pursued the growth of smooth, high-quality nonpolar a-plane and m-plane GaN films, as well as blue light emitting diodes on these novel films. Initial nonpolar LEDs showed the expected behavior of negligible peak wavelength shift with increasing drive current. M-plane LEDs in particular show promise, as unpackaged devices had unsaturated optical output power of ∼ 3 mW at 200 mA drive current. The LRC's tasks were aimed at developing the subcomponents necessary for packaging UCSB's light emitting diodes, and packaging them to produce a white light

Present status of corn grain disinfestation by irradiation in Mexico

Energy Technology Data Exchange (ETDEWEB)

Adem, E; Uribe, R M [Universidad Nacional Autonoma de Mexico, Mexico City. Inst. de Fisica; Watters, F L [Department of Agriculture, Winnipeg, Manitoba (Canada). Research Station; Bourges, H [Instituto Nacional de la Nutricion, Mexico City

1981-01-01

Progress in the use of ionizing radiation for the disinfestation of grain in Mexico is reviewed. Main topics described in the paper concern determination of optimum dose for disinfestation, comparison of Co-60 gamma rays and accelerated electrons for suppressing infestation, susceptibility of different strains of insects, dose rate effects on survival of different insect species, survival of progeny of irradiated insects, germinative tests, and effect of radiation on the nutrient content of corn. The technical and economical aspects of irradiation disinfestation are mentioned.

Some general requirements for irradiation experiments

Energy Technology Data Exchange (ETDEWEB)

Myers, H P; Skjoeldebrand, R

1960-05-15

This paper is limited to the interests of the EAES-symposium, namely the use of reactors for materials research and testing, for convenience we exclude consideration of chemical effects and problems of coolant technology. Its purpose is to try to define the general requirements for irradiation experiments and the reactors housing them; to see what facilities for irradiation experiments are available within the European Atomic Energy Society countries and finally, to point out possible limitations of these facilities.

International standards and agreements in food irradiation

International Nuclear Information System (INIS)

Cetinkaya, N.

2004-01-01

The economies of both developed and developing countries have been effected by their exported food and agricultural products. Trading policies of food and agricultural products are governed by international agreement as well as national regulations. Trade in food and agricultural commodities may be affected by both principal Agreements within the overall World Trade Organization (WTO) Agreement, though neither specifically refers to irradiation or irradiated foods. The principal Agreements are the Technical Barriers to Trade (TBT) Agreement and the Sanitary and Phyto sanitary (SPS) Agreement. The SPS of the WTO requires governments to harmonize their sanitary and phyto sanitary measures on as wide basis as possible. Related standards, guidelines and recommendations of international standard setting bodies such as the Codex Alimentarius Commission (food safety); the International Plant Protection Convention (IPPC) (plant health and quarantine); and International Office of Epizootic (animal health and zoo noses) should be used in such a harmonization. International Standards for Phyto sanitary Measures (ISPM) no.18 was published under the IPPC by FAO (April 2003, Rome-Italy). ISPM standard provides technical guidance on the specific procedure for the application of ionizing radiation as a phyto sanitary treatment for regulated pests or articles. Moreover, Codex Alimentarius Commission, Codex General Standard for Irradiated Foods (Stand 106-1983) and Recommended International Code of Practice were first published in 1983 and revised in March 2003. Scope of this standard applies to foods processed by ionizing radiation that is used in conjunction with applicable hygienic codes, food standards and transportation codes. It does not apply to foods exposed to doses imparted by measuring instruments used for inspection purposes. Codex documents on Principles and Guidelines for the Import/Export Inspection and Certification of Foods have been prepared to guide international

Inactivation of Lactobacillus plantarum by pulsed-microwave irradiation

International Nuclear Information System (INIS)

Shin, J.K.; Pyun, Y.R.

1997-01-01

Suspensions of Lactobacillus plantarum cells were subjected to either conventional heating, continuous microwave (CW) or pulsed microwave (PW) irradiation at 50 degrees C for 30 min. Samples exposed to PW showed greater reductions (2 approximately 4 log) in survival counts than those treated with either conventional heating or CW irradiation. As exposure time increased, PW resulted in a remarkable increase in 260 nm-absorbing compounds that leaked into the suspending menstruum, as compared to CW or conventional heating, indicating that PW irradiated cells were the most injured. The growth of PW irradiated cells was delayed about 24h and the final acidity of the culture broth was about 60 approximately 80% that of other cells treated with conventional heating or CW irradiation

Quality control in food irradiated with gamma radiations from Cobalt 60

International Nuclear Information System (INIS)

Bustos R, M.E.

1993-01-01

The quality control of irradiated food can only be carry out in the irradiation plant by means of the measurement of the absorbed dose by the product, since to day there is not exist a technique which allows to demonstrate that a food has been irradiated. Dosemeters are materials or devices which measure the absorbed dose by the product during the irradiation time. The type of the dosemeter is a choice as a function of factors as the range of dose for to reach of the desired technical purpose, the cost, the handling facility (handy) and its availability. The correct measurements of dose and dose distribution permits to indicate that the irradiation process is safe, effective and legally correct. The food quality after the irradiation is analyzed on basis and tests already established for a specific product: such tests can be sensory, chemical, physical or physiological> The quality control of the irradiation food is an important information for the consumer who wishes to know the food value and hygienic properties of the product. (Author)

Polar source analysis : technical memorandum

Science.gov (United States)

2017-09-29

The following technical memorandum describes the development, testing and analysis of various polar source data sets. The memorandum also includes recommendation for potential inclusion in future releases of AEDT. This memorandum is the final deliver...

Irradiation of Argentine MOX fuels: Post-irradiation results and analysis

International Nuclear Information System (INIS)

Marino, A.C.; Perez, E.; Adelfang, P.

1997-01-01

The irradiation of the first Argentine prototypes of PHWR MOX fuels began in 1986. These experiments were made in the HFR-Petten reactor, Holland. The rods were prepared and controlled in the CNEA's facility. The postirradiation examinations were performed in the Kernforschungszentrum, Karlsruhe, Germany and in the JRC, Petten. The first rod has been used for destructive pre-irradiation analysis. The second one as a pathfinder to adjust systems in the HFR. Two additional rods including iodine doped pellets were intended to simulate 15000 MWd/T(M) burnup. The remaining two rods were irradiated until 15000 MWd/T(M) (BU15 experiment). One of them underwent a final ramp with the aim of verifying fabrication processes and studying the behaviour under power transients. BACO code was used to define the power histories and to analyze the experiments. This paper presents the postirradiation examinations for the BU15 experiments and a comparison with the BACO outputs for the rod that presented a failure during the ramp test of the BU15 experiment. (author). 17 refs, 30 figs, 5 tabs

AGC-2 Irradiation Data Qualification Final Report

Energy Technology Data Exchange (ETDEWEB)

Laurence C. Hull

2012-07-01

The Graphite Technology Development Program will run a series of six experiments to quantify the effects of irradiation on nuclear grade graphite. The second Advanced Graphite Creep (AGC) experiment (AGC-2) began with Advanced Test Reactor (ATR) Cycle 149A on April 12, 2011, and ended with ATR Cycle 151B on May 5, 2012. The purpose of this report is to qualify AGC-2 irradiation monitoring data following INL Management and Control Procedure 2691, Data Qualification. Data that are Qualified meet the requirements for data collection and use as described in the experiment planning and quality assurance documents. Data that do not meet the requirements are Failed. Some data may not quite meet the requirements, but may still provide some useable information. These data are labeled as Trend. No Trend data were identified for the AGC-2 experiment. All thermocouples functioned throughout the AGC-2 experiment. There was one instance where spurious signals or instrument power interruption resulted in a recorded temperature value being well outside physical reality. This value was identified and labeled as Failed data. All other temperature data are Qualified. All helium and argon gas flow data are within expected ranges. Total gas flow was approximately 50 sccm through the capsule. Helium gas flow was briefly increased to 100 sccm during reactor shutdown. All gas flow data are Qualified. At the start of the experiment, moisture in the outflow gas line increased to 200 ppmv then declined to less than 10 ppmv over a period of 5 days. This increase in moisture coincides with the initial heating of the experiment and drying of the system. Moisture slightly exceeded 10 ppmv three other times during the experiment. While these moisture values exceed the 10 ppmv threshold value, the reported measurements are considered accurate and to reflect moisture conditions in the capsule. All moisture data are Qualified. Graphite creep specimens are subjected to one of three loads, 393 lbf

Perspectives of food irradiation

International Nuclear Information System (INIS)

Miettinen, J.K.

1974-01-01

Food preservation by means of ionizing radiation has been technically feasible for more than a decade. Its utilization could increase food safety, extend the transport and shell life of foods, cut food losses, and reduce dependence upon chemical additives. The prime obstacles have been the strict safety requirements set by health authorities to this preservation method and the high costs of the long-term animal tests necessary to fulfil these requirements. An International Food Irradiation Project, expected to establish the toxicological safety of 10 foods by about 1976, is described in some detail. (author)

Dosimetry during mango irradiation using Gafchromic HD-810 film

International Nuclear Information System (INIS)

Sharma, S. D.; Chilkulwar, R. H.; Kumar, R.

2009-01-01

The dosimetric characteristics of Gafchromic HD-810 film were evaluated for its possible use as a high-dose dosemeter for routine dosimetry during mango irradiation. The film dosemeter sample of size 2 x 2 cm 2 was used throughout the course of this work. The irradiation of the film dosemeter for characterisation and calibration purposes was carried out in a gamma irradiator. The dose-response of the Gafchromic HD-810 film dosemeter at 550 nm was found to be linear in the dose range 50-1000 Gy, which indicates the feasibility of using this film for dosimetry up to 1000 Gy. The mean inter-dosemeter variation was within 2%, which gives better dose-response consistency of the HD-810 film. The radiation absorbed dose measured by the Gafchromic HD-810 film dosemeter during mango irradiation was compared with that measured by a standard Ceric-cerous dosemeter. This study establishes the Gafchromic HD-810 film as a convenient and technically suitable dosemeter for high-dose dosimetry up to 1.0 kGy during mango irradiation. (authors)

Technical Report for a Study on the Mechanism and Control of Non-Enzymatic Browning Reaction in Gamma-Irradiated Food

Energy Technology Data Exchange (ETDEWEB)

Byun, Myung Woo; Lee, Ju Woon; Kim, Jae Hun

2007-01-15

Gamma irradiation leads to a non-enzymatic browning reaction (carbonyl -amine reaction) in an aqueous system similar to those induced in a heated one. This reaction may influence the changes of the color in irradiated foods. The intensity of the reaction was dependent on the type of the sugar, if the occurrence is by irradiation or by heating. There was a difference in the browning reaction between irradiation and heating. Although no browning was observed in the heated solution of the non-reducing sugar, the formation of colored products was observed in the irradiated sucrose-lysine solution. It could be explained on the basis that irradiation promotes the breakdown of the glycosidic linkages of the disaccharide, sucrose and the produce of a reducing power. The high molecular weight melanoidin (> MW 12,000-14,000 Da) was produced by gamma irradiation from the non-enzymatic browning reaction between glucose and glycine. The structure of melanoidin was similar to melanodin from heat processing. The results suggested that gamma-irradiation occurred the non-enzymatic browning reaction that is similar the reaction by heat processing. Non-enzymatic browning reaction during gamma-irradiation processing was greatly influenced by pH and medium of reaction system. The brown color development of irradiated sugar solutions with and without glycine is more increased in buffer system especially with alkaline pH than DDW. When food is irradiated, off-color such as browning can be produced due to the non-enzymatic browning reaction and it is influenced by other ions and/or pH of system. This suggests that the browning of irradiated food might be retarded by lowering the pH of the system. Gamma-irradiation produce the free radical and the radiolysis products of sugar and glycine and then they may be condensed to colored products during post-irradiation. However, when the food is irradiated in frozen state, the production of free radical and radiolysis product is inhibited and it

Technical Report for a Study on the Mechanism and Control of Non-Enzymatic Browning Reaction in Gamma-Irradiated Food

International Nuclear Information System (INIS)

Byun, Myung Woo; Lee, Ju Woon; Kim, Jae Hun

2007-01-01

Gamma irradiation leads to a non-enzymatic browning reaction (carbonyl -amine reaction) in an aqueous system similar to those induced in a heated one. This reaction may influence the changes of the color in irradiated foods. The intensity of the reaction was dependent on the type of the sugar, if the occurrence is by irradiation or by heating. There was a difference in the browning reaction between irradiation and heating. Although no browning was observed in the heated solution of the non-reducing sugar, the formation of colored products was observed in the irradiated sucrose-lysine solution. It could be explained on the basis that irradiation promotes the breakdown of the glycosidic linkages of the disaccharide, sucrose and the produce of a reducing power. The high molecular weight melanoidin (> MW 12,000-14,000 Da) was produced by gamma irradiation from the non-enzymatic browning reaction between glucose and glycine. The structure of melanoidin was similar to melanodin from heat processing. The results suggested that gamma-irradiation occurred the non-enzymatic browning reaction that is similar the reaction by heat processing. Non-enzymatic browning reaction during gamma-irradiation processing was greatly influenced by pH and medium of reaction system. The brown color development of irradiated sugar solutions with and without glycine is more increased in buffer system especially with alkaline pH than DDW. When food is irradiated, off-color such as browning can be produced due to the non-enzymatic browning reaction and it is influenced by other ions and/or pH of system. This suggests that the browning of irradiated food might be retarded by lowering the pH of the system. Gamma-irradiation produce the free radical and the radiolysis products of sugar and glycine and then they may be condensed to colored products during post-irradiation. However, when the food is irradiated in frozen state, the production of free radical and radiolysis product is inhibited and it

Vehicle infrastructure integration proof of concept : technical description--vehicle : final report

Science.gov (United States)

2009-05-19

This report provides the technical description of the VII system developed for the Cooperative Agreement VII Program between the USDOT and the VII Consortium. The basic architectural elements are summarized and detailed descriptions of the hardware a...

Repair-welding technology of irradiated materials - WIM project

International Nuclear Information System (INIS)

Nakata, K.; Oishi, M.

1998-01-01

A new project on the development of repair-welding technology for core internals and reactor (pressure) vessel, consigned by the Ministry of International Trade and Industry (MITI), has been started from October 1997. The objective of the project is classified into three points as follows: (1) to develop repair-welding techniques for neutron irradiated materials, (2) to prove the availability of the techniques for core internals and reactor (pressure) vessel, and (3) to recommend the updated repair-welding for the Technical Rules and Standards. Total planning, neutron irradiation, preparation of welding equipment are now in progress. The materials are austenitic stainless steels and a low alloy steel. Neutron irradiation is performed using test reactors. In order to suppress the helium aggregation along grain boundaries, low heat input welding techniques, such as laser, low heat input TIG and friction weldings, will be applied. (author)

Final Scientific and Technical Report State and Regional Biomass Partnerships

Energy Technology Data Exchange (ETDEWEB)

Handley, Rick; Stubbs, Anne D.

2008-12-29

The Northeast Regional Biomass Program successfully employed a three pronged approach to build the regional capacity, networks, and reliable information needed to advance biomass and bioenergy technologies and markets. The approach included support for state-based, multi-agency biomass working groups; direct technical assistance to states and private developers; and extensive networking and partnership-building activities to share objective information and best practices.

Development of indigenous irradiator - current progress and challenges

International Nuclear Information System (INIS)

Anwar A Rahman; Mohd Arif Hamzah; Muhd Nor Atan; Aznor Hassan; Fadil Ismail; Julia A Karim; Rosli Darmawan

2009-01-01

The development of indigenous irradiator is one of Prototype Development Center main project to support Nuclear Malaysia services. Three (3) projects have been identified and currently the status is in final stage of design. There are some issues and challenges encountered, which delayed the project progress. The paper will discuss the current progress of development and challenges faced in designing the irradiator. (Author)

Legal aspects and international implications of food irradiation

International Nuclear Information System (INIS)

Gerard, Alain.

1977-11-01

This paper reports on the status of work on food irradiation at international level, namely the IAEA/FAO/WHO Vienna recommendations, the proposed EEC directive, and the Codex alimentarius draft standards. It then deals with the legal aspects of the subject, in particular the problems concerning definitions, controls and instructions, and finally reviews the regulations for international trade in irradiated foodstuffs. (NEA) [fr

Hydraulic containment of low-level radioactive waste disposal sites: [Final technical report

International Nuclear Information System (INIS)

Ostendorf, D.W.; Noss, R.R.; Miller, A.B.; Phillips, H.S.

1987-01-01

This document describes the use of impermeable barriers for the containment of liquid radioactive wastes at low-level radioactive waste disposal sites. Included are a review of existing barrier systems, assessments of laboratory and field data, and simulations of system performance under humid and arid conditions. Alternatives are identified as the most promising of the existing systems based on retention of irradiated water, field installation feasibility, and response to aggressive permeation. In decreasing order of preference, the favored systems are asphalt slurry, high density polyethylene synthetic liner, polyvinyl chloride synthetic liner, lean portland cement concrete, and compacted bentonite liner. It should be stressed that all five of these alternatives effectively retain irradiated water in the humid and arid simulations. Recommendations on the design and operation of the hydraulic containment system and suggestions on avenues for future research are included. 102 refs., 27 figs., 23 tabs

NUSC Technical Publications Guide.

Science.gov (United States)

1985-05-01

Facility personnel especially that of A. Castelluzzo, E. Deland, J. Gesel , and E. Szlosek (all of Code 4343). Reviewed and Approved: 14 July 1980 D...their technical content and format. Review and approve the manual outline, the review manuscript, and the final camera - reproducible copy. Conduct in

More than 2 years' experience with computer-aided irradiation planning in clinical routine

International Nuclear Information System (INIS)

Heller, H.; Rathje, J.

1976-01-01

This is a report on an irradiation planning system which has been used for about 2 years in the department of radiotherapy in the general hospital in Altona. Hard- and software as well as the mathematical model for the description of the dose distribution are described. The compromise between the required accuray of the irradiation plan and the investment in computer-technical activities and computer time is discussed. (orig./LN) [de

Treatment of toxic gases SO2 and NO X by electron beam irradiation

International Nuclear Information System (INIS)

Castro Rubio Poli, D. de; Vieira, J.M.; Campos, C.A. de.

1993-01-01

The removal of S O 2 and N O x by electron beam irradiation will be studied using a small scale flow system which is being set up in order to obtain basic data for the process technical and economical feasibility concerning industrial applications. The gas irradiation will be performed using a Electron Beam Accelerator with 1,5 MeV power, 25 m A current from Radiation Dynamics, Inc. USA. (author)

Aging irradiation of polymers. Dose-rate and test sequence influence

International Nuclear Information System (INIS)

Alba, C.; Carlin, F.; Chenion, J.; Lemaire, F.; Le Meur, M.; Petitjean, M.

1984-05-01

This work brings up results of the irradiation dose-rate influence on mechanical and electrical properties of technical polymer materials evolution. Polymer samples were subjected to 3.3.10 -2 Gy.s -1 and 2.8.10 -1 Gy.s -1 dose-rate. Heat and radiation simultaneous action is usualy simulated sequentialy. The hardest simulation on the polymer is the sequence of irradiation followed by thermal aging not the reverse. This study was carried out on eight polymer materials among those used in the electrical appliances for P.W.R. nuclear power plants [fr

Ultraviolet irradiation of nucleic acids and related compounds. Final progress report

International Nuclear Information System (INIS)

Wang, S.Y.

1976-01-01

Progress is reported on the following research projects: photohydration of pyrimidine derivatives; thymine dimerization; uv-induced formation of pyrimidinyl radicals; formation of a coupled product by irradiation of 5-bromouracil derivatives; studies on pyrimidine adducts; molecular aggregates-puddle formation hypothesis of pyrimidine photodimerization; and topochemical studies of structures of dimers and of crystalline arrangements

Medium energy measurements of N-N parameters. Final technical report, April 1, 1994--September 30, 1996

International Nuclear Information System (INIS)

Ambrose, D.; Betts, W.; Coffey, P.; Glass, G.; McDonough, J.; Riley, P.; Tang, J.L.

1998-08-01

This document is a final technical report describing the accomplishments of the medium/high energy nuclear physics research program at the University of Texas at Austin. The research program had four main thrusts, only one of which can be considered as measurements of N-N parameters: (1) finishing the data analyses associated with recent LAMPF and TRIUMPF N-N experiments, whose overall purpose has been the determination of the nucleon-nucleon amplitudes, both for isospin 0 and 1 at medium energies; (2) continuing work on BNL E871, a search for rare decay modes of the K L ; (3) work on the RHIC-STAR project, an experiment to create and study a quark gluon plasma and nuclear matter at high energy density; (4) beginning a new AGS experiment (E896) which will search for the lowest mass state of the predicted strange di-baryons, the Ho, and other exotic states of nuclear matter through nucleus-nucleus collisions

Current status of food irradiation in overseas (2013). From the meeting report of RCA food irradiation project

International Nuclear Information System (INIS)

Todoriki, Setsuko

2013-01-01

The report introduces the activity of RCA (Regional Cooperative Agreement for Research Development and Training Related to Nuclear Science and Technology for Asia and Pacific) food irradiation project (RAS/5/057) and information obtained at the two workshops on current status of Asia and Pacific areas together with EU, USA and Japan. Also current trends of RAS/5/057 Implementing Best Practices for food irradiation for plant sanitary and phytosanitary purposes are described. Amount of food irradiation products of RCA member countries, minimum adopted doses for quarantine harmful insects (70 to 232 Gy) and import amount of fruits of USA (79 to 5500 tons) are tabulated. Finally current status of Japan is explained. (S. Ohno)

Quality of 'Climax' blueberries after low dosage electron beam irradiation

International Nuclear Information System (INIS)

Miller, W.R.; McDonald, R.E.; McCollum, T.G.; Smittle, B.J.

1994-01-01

Fruit of 'Climax' rabbiteye blueberries (Vaccinium ashei Reade) were irradiated by a linear accelerator at 0, 0.25, 0.5, 0.75, 1.0, and 1.25 kGy and evaluated for various quality attributes after storage for 1, 3, 7, or 14 days at 1C plus 2 days at 15C, respectively. Weight loss increased during storage and averaged 4.2% after the final inspection and was not affected by irradiation dosage. About 5% of total berries were decayed after 14 days at 1C, about 6% after the final inspection at 15C, but decay was not affected by the level of irradiation. Electrolyte leakage, skin color, total soluble solids, acidity, and pH were also not affected by irradiation dosage. There was a significant decline in berry firmness, flavor, and texture as dosage increased. Berries treated at 1.0 kGy or above were softer and had lower flavor and texture preference scores than berries treated at lower dosages or nontreated berries

Argentine project for the final disposal of high-level radioactive wastes

International Nuclear Information System (INIS)

Palacios, E.; Ciallella, N.R.; Petraitis, E.J.

1989-01-01

From 1980 Argentina is carrying out a research program on the final disposal of high level radioactive wastes. The quantity of wastes produced will be significant in next century. However, it was decided to start with the studies well in advance in order to demonstrate that the high level wastes could be disposed in a safety way. The option of the direct disposal of irradiated fuel elements was discarded, not only by the energetic value of the plutonium, but also for ecological reasons. In fact, the presence of a total inventory of actinides in the non-processed fuel would imply a more important radiological impact than that caused if the plutonium is recycled to produce energy. The decision to solve the technological aspects connected with the elimination of high-level radioactive wastes well in advance, was made to avoid transfering the problem to future generations. This decision is based not only on technical evaluations but also on ethic premises. (Author)

NTRCI Legacy Engine Research and Development Project Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Smith-Holbert, Connie [National Transportation Research Center, Inc., Knoxville, TN (United States); Petrolino, Joseph [National Transportation Research Center, Inc., Knoxville, TN (United States); Watkins, Bart [Power Source Technologies Inc., Corvallis, OR (United States); Irick, David [Power Source Technologies Inc., Corvallis, OR (United States)

2011-12-31

The Legacy engine is a completely new design, transitional diesel engine, replacing the reciprocating engine with a rotary engine. The Legacy engine offers significant advances over conventional internal combustion engines in 1) power to weight ratio; 2) multiple fuel acceptance; 3) fuel economy; and 4) environmental compliance. These advances are achieved through a combination of innovative design geometry, rotary motion, aspiration simplicity, and manufacturing/part simplicity. The key technical challenge to the Legacy engine's commercialization, and the focus of this project, was the development of a viable roton tip seal. The PST concept for the roton tip seal was developed into a manufacturable design. The design was evaluated using a custom designed and fabricated seal test fixture and further refined. This design was incorporated into the GEN2.5A prototype and tested for achievable compression pressure. The Decision Point at the end of Phase 1 of the project (described below) was to further optimize the existing tip seal design. Enhancements to the tip seal design were incorporated into the GEN2.5B prototype and tested and evaluated using the iterative research strategy described below. Compression pressures adequate for compression ignition of diesel fuel were achieved, although not consistently in all combustion volumes. The variation in compression pressures was characterized versus design features. As the roton tip seal performance was improved, results pointed toward inadequate performance of the housing side seals. Enhancement of the housing side seal system was accomplished using a custom designed side seal test fixture. The design enhancements developed with the test fixture were also incorporated into the GEN2.5B prototype and tested and evaluated using the iterative research strategy described below. Finally, to simplify the requirements for the roton tip seals and to enhance the introduction and combustion of fuel, a flush-mount fuel injector

Final Scientific/Technical Report

Energy Technology Data Exchange (ETDEWEB)

Brown, R. C.; McCarley, T. M.

2006-05-04

. Platform teams organize faculty and students for cross-disciplinary, systems-oriented research and collaborative learning. To date, nine platforms have been developed, although these will most likely be reorganized into a smaller number of broader topics. In the spring of 2004, BRT faculty initiated a regional partnership and collaborative learning program with colleagues at the University of Minnesota, Kansas State University, and South Dakota State University to develop distance education courses in biorenewable resources and technology. As a fledgling graduate program, the BRT graduate program didn’t have the breadth of resources to offer a large number of courses in biorenewables. Other schools faced a similar problem. The academic consortium as first conceived would allow students from the member schools to enroll in biorenewables courses from any of the participating schools, which would assure the necessary enrollment numbers to offer specialized course work. Since its inception, the collaborative curriculum partnership has expanded to include Louisiana State University and the University of Wisconsin. A second international curriculum development campaign was also initiated in the spring of 2004. In particular, several BRT faculty teamed with colleagues at the University of Arkansas, University of Washington, University of Gent (Belgium), National Polytechnic Institute of Toulouse (France), and Technical University of Graz (Austria) to develop an EU-US exchange program in higher education and vocational education/training (entitled “Renewable Resources and Clean Technology”).

Preliminary irradiation test results from the Yankee Atomic Electric Company reactor vessel test irradiation program

International Nuclear Information System (INIS)

Biemiller, E.C.; Fyfitch, S.; Campbell, C.A.

1993-01-01

The Yankee Atomic Electric Company test irradiation program was implemented to characterize the irradiation response of representative Yankee Rowe reactor vessel beltline plate materials and to remove uncertainties in the analysis of existing irradiation data on the Yankee Rowe reactor vessel steel. Plate materials each containing 0.24 w/o copper, but different nickel contents at 0.63 w/o and 0.19 w/o, were heat treated to simulate the Yankee vessel heat treatment (austenitized at 1800 deg F) and to simulate Regulatory Guide 1.99 database materials (austenitized at 1600 deg. F). These heat treatments produced different microstructures so the effect of microstructure on irradiation damage sensitivity could be tested. Because the nickel content of the test plates varied and the copper level was constant, the effect of nickel on irradiation embrittlement was also tested. Correlation monitor material, HSST-02, was included in the program to benchmark the Ford Nuclear Reactor (U. of Michigan Test Reactor) which had never been used for this type of irradiation program. Materials taken from plate surface locations (vs. 1/4T) were included to test whether or not the improved toughness properties of the plate surface layer, resulting from the rapid quench, is maintained after irradiation. If the improved properties are maintained, pressurized thermal shock calculations could utilize this margin. Finally, for one experiment, irradiations were conducted at two irradiation temperatures (500 deg. F and 550 deg. F) to determine the effect of irradiation temperature on embrittlement. The preliminary results of the irradiation program show an increase in T 30 shift of 69 deg. F for a decrease in irradiation temperature of 50 deg. F. The results suggest that for nickel bearing steels, the superior toughness of plate surface material is maintained after irradiation and for the copper content tested, nickel had no apparent effect on irradiation response. No apparent microstructure

Amorphization kinetics of Zr3Fe under electron irradiation

International Nuclear Information System (INIS)

Motta, A.T.; Howe, L.M.; Okamoto, P.R.

1992-10-01

0.9 MeV electron irradiations were performed at 28--220 K in a high-voltage electron microscope (HVEM). By measuring onset, spread and final size of the amorphous region, factoring in the Guassian distribution of the beam, a kinetic description of the amorphization in terms of dose, dose rate and temperature was obtained. The critical temperature for amorphization by electron irradiation was found to be ∼220 K, compared to 570--625 K for 40 Ar ion irradiation. Also, the dose-to-amorphization increased exponentially with temperature. Results indicated that the rate of growth of the amorphous region under the electron beam decreased with increasing temperature and the does-to-amorphization decreased with increasing dose rate. The size of the amorphous region saturated after a region dose, the final size decreasing with increasing temperature, and it was argued that this is related to the existence of a critical dose rate, which increased with temperature, below which no amorphization occurred. The above observations can be understood in the framework of the kinetics of damage accumulation under irradiation

Effectiveness of thermoluminescence analysis to detect low quantity of gamma-irradiated component in non-irradiated mushroom powders

International Nuclear Information System (INIS)

Akram, Kashif; Ahn, Jae-Jun; Shahbaz, Hafiz Muhammad; Jo, Deokjo; Kwon, Joong-Ho

2013-01-01

Gamma-irradiated (0–10 kGy) dried mushrooms (Lentinus edodes) powders were mixed at different ratios (1–10%) in the non-irradiated samples and investigated using photostimulated-luminescence (PSL), electron spin resonance (ESR) and thermoluminescence (TL) techniques. The PSL results were negative for all samples at 1% mixing ratio, whereas intermediate results were observed for the samples containing 5% or 10% irradiated component with the exception (positive) of 10% mixing of 10 kGy-irradiated sample. The ESR analysis showed the presence of crystalline sugar radicals in the irradiated samples but the radiation-specific spectral features were absent in the mixed samples. TL analysis showed the radiation-specific TL glow curves; however, the complicated results were observed at 1% mixing of 2 and 5 kGy-irradiated samples, which required careful evaluations to draw the final conclusion about the irradiation status of the samples. TL ratios could only confirm the results of samples with 5% and 10% mixing of 10 kGy, and 10% mixing of 5 kGy-irradiated components. SEM-EDX analysis showed that feldspar and quartz were major contaminating minerals, responsible for the radiation-specific luminescence characteristics. -- Highlights: ► Detection of irradiated food is important to enforce the applied regulations. ► The effectiveness of TL analysis was investigated to detect irradiated component. ► The TL results were compared with those from PSL and ESR analysis. ► TL analysis was most effective to characterize the irradiation status of samples. ► SEM-EDX analysis showed feldspar and quartz as the main source of TL properties

Effectiveness of thermoluminescence analysis to detect low quantity of gamma-irradiated component in non-irradiated mushroom powders

Energy Technology Data Exchange (ETDEWEB)

Akram, Kashif [School of Food Science and Biotechnology, Kyungpook National University, Daegu 702-701 (Korea, Republic of); Institute of Food Science and Nutrition, University of Sargodha, Sargodha 40100 (Pakistan); Ahn, Jae-Jun [School of Food Science and Biotechnology, Kyungpook National University, Daegu 702-701 (Korea, Republic of); Shahbaz, Hafiz Muhammad [School of Food Science and Biotechnology, Kyungpook National University, Daegu 702-701 (Korea, Republic of); Institute of Food Science and Nutrition, University of Sargodha, Sargodha 40100 (Pakistan); Jo, Deokjo [School of Food Science and Biotechnology, Kyungpook National University, Daegu 702-701 (Korea, Republic of); Kwon, Joong-Ho, E-mail: jhkwon@knu.ac.kr [School of Food Science and Biotechnology, Kyungpook National University, Daegu 702-701 (Korea, Republic of)

2013-04-15

Gamma-irradiated (0–10 kGy) dried mushrooms (Lentinus edodes) powders were mixed at different ratios (1–10%) in the non-irradiated samples and investigated using photostimulated-luminescence (PSL), electron spin resonance (ESR) and thermoluminescence (TL) techniques. The PSL results were negative for all samples at 1% mixing ratio, whereas intermediate results were observed for the samples containing 5% or 10% irradiated component with the exception (positive) of 10% mixing of 10 kGy-irradiated sample. The ESR analysis showed the presence of crystalline sugar radicals in the irradiated samples but the radiation-specific spectral features were absent in the mixed samples. TL analysis showed the radiation-specific TL glow curves; however, the complicated results were observed at 1% mixing of 2 and 5 kGy-irradiated samples, which required careful evaluations to draw the final conclusion about the irradiation status of the samples. TL ratios could only confirm the results of samples with 5% and 10% mixing of 10 kGy, and 10% mixing of 5 kGy-irradiated components. SEM-EDX analysis showed that feldspar and quartz were major contaminating minerals, responsible for the radiation-specific luminescence characteristics. -- Highlights: ► Detection of irradiated food is important to enforce the applied regulations. ► The effectiveness of TL analysis was investigated to detect irradiated component. ► The TL results were compared with those from PSL and ESR analysis. ► TL analysis was most effective to characterize the irradiation status of samples. ► SEM-EDX analysis showed feldspar and quartz as the main source of TL properties.

Effect of low-dose gamma irradiation on storage properties in light salted Pseudosciaena crocea

International Nuclear Information System (INIS)

Zhang Xiaoyan; Yang Xianshi; Li Xueying; Guo Quanyou

2012-01-01

To explore the preservation effect of γ irradiation on light salted Pseudosciaena crocea, the influence of 1 kGy low-dose γ irradiation on sensory quality, microbiological and chemical quality including TVC, TVB-N and TBARS contents of light salted P. crocea stored at 25 ℃ was discussed. The results showed that the number of total viable counts significantly decreased after irradiation, during the whole storage, the bacteria numbers of light salted P. crocea treated with irradiation were still less than the control. The concentrations of TVB-N was significantly reduced after irradiation, whereas lipid oxidation was less accelerated. The shelf life could be remarkably prolonged after low-dose γ irradiation. While the shelf life of control group were 9 and 11 days, the shelf life of irradiated light salted P. crocea were extended to 16 and 20 days, respectively. The results can provide technical references for commercial application of seafood irradiation. (authors)

Technical assistance for Meharry Medical College Energy Efficiency Project. Final project status and technical report

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-05-08

This report presents the results of a program to provide technical assistance to Meharry Medical College. The purpose of the program is to facilitate Meharry`s effort to finance a campus-wide facility retrofit. The US Department of Energy (USDOE) funded the program through a grant to the Tennessee Department of Economic and Community Development (TECD). The University of Memphis-Technology and Energy Services (UM-TES), under contract to TECD, performed program services. The report has three sections: (1) introduction; (2) project definition, financing, and participants; and (3) opportunities for federal participation.

Fundamental studies of the chemical vapor deposition of diamond. Final technical report, April 1, 1988--December 31, 1994

Energy Technology Data Exchange (ETDEWEB)

Nix, W.D.

1995-05-01

We submit here a final technical report for the research program entitled: Fundamental Studies of the Chemical Vapor Deposition of Diamond, DOE Grant No. DE-FG05-88ER45345-M006. This research program was initiated in 1988 under the direction of the late Professor David A. Stevenson and was renewed in 1992. Unfortunately, at the end of 1992, just as the last phase of this work was getting underway, Professor Stevenson learned that he had developed mesothelioma, a form of cancer based on asbestos. Professor Stevenson died from that disease in February of 1994. Professor William D. Nix, the Chairman of the Materials Science department at Stanford was named the Principal Investigator. Professor Nix has assembled this final technical report. Much of the work of this grant was conducted by Mr. Paul Dennig, a graduate student who will receive his Ph.D. degree from Stanford in a few months. His research findings are described in the chapters of this report and in the papers published over the past few years. The main discovery of this work was that surface topology plays a crucial role in the nucleation of diamond on silicon. Dennig and his collaborators demonstrated this by showing that diamond nucleates preferentially at the tips of asperities on a silicon surface rather than in the re-entrant comers at the base of such asperities. Some of the possible reasons for this effect are described in this report. The published papers listed on the next page of this report also describe this research. Interested persons can obtain copies of these papers from Professor Nix at Stanford. A full account of all of the research results obtained in this work is given in the regular chapters that follow this brief introduction. In addition, interested readers will want to consult Mr. Dennig`s Ph.D. dissertation when it is made available later this year.

Use of gamma radiation as a form of preservation of sweet potatoes. [Final technical] quarterly progress report

International Nuclear Information System (INIS)

1985-01-01

This document covers: harvest and conditioning following harvest, harvest-curing-storage-irradiation schemes, irradiation, control sweet potatoes, analyses, enzymes results, and procedures for taste evaluation, storage rot, weevil

Modernization of the irradiation apparatus for nuclear instrument calibration laboratory of the Paks Nuclear Power Plant, Hungary

International Nuclear Information System (INIS)

Orban, M.; Csete, I.; Lenart, A.

1993-01-01

The National Office of Measures, OMH of Hungary, has made several proposals for improving technical and personal conditions of metrological inspection of calibration apparatuses at PNPP, Hungary. Some recent improvement of irradiation facilities are described, including the collimator system of the large gamma irradiation facility, the small gamma irradiation gun, and the Pu-Be neutron gun. The upgrading operations and results of these equipment are presented. (N.T.) 4 figs.; 1 tab

Minutes of the IFMIF technical meeting

International Nuclear Information System (INIS)

Nakamura, H.; Takeda, M.; Ida, M.; Maebara, S.; Yutani, T.; Sugimoto, M.

2004-03-01

The IFMIF Technical Meeting was held on December 4-5, 2003 at Shiran-kaikan, Kyoto University. The main objectives are 1) to finalize the Comprehensive Design Report (CDR), 2) to discuss IFMIF cost and organization, 3) to review technical status of major systems, transition phase activities and EVEDA plan. This report presents a brief summary of the results of the meeting. Agenda, participants list and presentation materials are attached as Appendix. (author)

Design of boron carbide-shielded irradiation channel of the outer irradiation channel of the Ghana Research Reactor-1 using MCNP.

Science.gov (United States)

Abrefah, R G; Sogbadji, R B M; Ampomah-Amoako, E; Birikorang, S A; Odoi, H C; Nyarko, B J B

2011-01-01

The MCNP model for the Ghana Research Reactor-1 was redesigned to incorporate a boron carbide-shielded irradiation channel in one of the outer irradiation channels. Extensive investigations were made before arriving at the final design of only one boron carbide covered outer irradiation channel; as all the other designs that were considered did not give desirable results of neutronic performance. The concept of redesigning a new MCNP model, which has a boron carbide-shielded channel is to equip the Ghana Research Reactor-1 with the means of performing efficient epithermal neutron activation analysis. After the simulation, a comparison of the results from the original MCNP model for the Ghana Research Reactor-1 and the new redesigned model of the boron carbide shielded channel was made. The final effective criticality of the original MCNP model for the GHARR-1 was recorded as 1.00402 while that of the new boron carbide designed model was recorded as 1.00282. Also, a final prompt neutron lifetime of 1.5245 × 10(-4)s was recorded for the new boron carbide designed model while a value of 1.5571 × 10(-7)s was recorded for the original MCNP design of the GHARR-1. Copyright © 2010 Elsevier Ltd. All rights reserved.

Vanderbilt University Gamma Irradiation of Nano-modified Concrete (2017 Milestone Report)

Energy Technology Data Exchange (ETDEWEB)

Deichert, Geoffrey G. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Linton, Kory D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Terrani, Kurt A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Selby, Aaron P. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Reches, Yonathan [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-08-01

This document outlines the irradiation of concrete specimens in the Gamma Irradiation Facility in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL). Two gamma irradiation runs were performed in July of 2017 on 18 reference mortar bar specimens, 26 reference cement paste bar specimens, and 28 reference cement paste tab specimens to determine the dose and temperature response of the specimens in the gamma irradiation environment. Specimens from the first two gamma irradiations were surveyed and released to Vanderbilt University. The temperature and dose information obtained informs the test parameters of the final two gamma irradiations of nano-modified concrete planned for FY 2018.

Establishment of the International Power Institute. Final technical report

Energy Technology Data Exchange (ETDEWEB)

Julius E. Coles

2000-08-04

The International Power Institute, in collaboration with American industries, seeks to address technical, political, economic and cultural issues of developing countries in the interest of facilitating profitable transactions in power related infrastructure projects. IPI works with universities, governments and commercial organizations to render project-specific recommendations for private-sector investment considerations. IPI also established the following goals: Facilitate electric power infrastructure transactions between developing countries and the US power industry; Collaborate with developing countries to identify development strategies to achieve energy stability; and Encourage market driven solutions and work collaboratively with other international trade energy, technology and banking organizations.

Food irradiation newsletter. V.18, no.1

International Nuclear Information System (INIS)

1994-04-01

This newsletter contains a report on the 10th Annual Meeting of the International Consultative Group on Food Irradiations, summaries of the Second Research Co-ordination Meetings(RCMs) and Final RCM of the Asian Regional Co-operative Project on Food Irradiation with Emphasis on Process Control and Applications(RPFI-Pase III), the resolutions and considerations of food irradiation by the IAEA Board and summaries of the Regional Project for Research, Developing and Training on the Application of Nuclear Techniques to Food Preservation in the Near East. Reviews and order information for new publications and a listing of future meetings and workshops are located in the back of this newsletter

Food irradiation newsletter. V. 19, no. 1

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-04-01

Several other important developments are covered in this issue. The high profile CRP on Analytical Detection Methods for Irradiation Treatment of Food (ADMIT) came to the conclusion at the final RCM held at the Department of Agriculture, Belfast, Northern Ireland in June 1994. This CRP has achieved the task which to many of us would be practically impossible. Thanks to the efforts of the participants and modern sensitive scientific equipment, the CRP was able to develop several reliable detection methods for various types of irradiated food. The outcome of the RCM on Irradiation as a Quarantine Treatment of Mites, Nematodes and Insects other than Fruit Fly, held in Bangkok, March 1994 also provided further encouragement for expanding the use of irradiation as a quarantine treatment beyond fruit fly infestation.

Modification of polycrystalline copper by proton irradiation

International Nuclear Information System (INIS)

Garcia S, F.; Cabral P, A.; Saniger B, J.M.; Banuelos, J.G.; Barragan V, A.

1997-01-01

Polished copper samples were irradiated with proton beams of 300 and 700 keV at room temperature and at -150 Centigrade. In this work the obtained results are reported when such copper irradiated samples are analysed with Sem, Tem, AFM. The Sem micrographs showed evident changes in surface of these copper samples, therefore an EDAX microanalysis was done for its characterization. additionally, the Tem micrographs showed heaps formation until 200 nm. Its electron diffraction spectra indicated that these heaps consist of a copper compound. Finally with AFM were observed changes in coloration of the irradiated sample surface, as well as changes in texture and rugosity of them. These results show in general that irradiation process with protons which is known as an innocuo process produces changes in the copper properties. (Author)

Food irradiation newsletter. V. 19, no. 1

International Nuclear Information System (INIS)

1995-04-01

Several other important developments are covered in this issue. The high profile CRP on Analytical Detection Methods for Irradiation Treatment of Food (ADMIT) came to the conclusion at the final RCM held at the Department of Agriculture, Belfast, Northern Ireland in June 1994. This CRP has achieved the task which to many of us would be practically impossible. Thanks to the efforts of the participants and modern sensitive scientific equipment, the CRP was able to develop several reliable detection methods for various types of irradiated food. The outcome of the RCM on Irradiation as a Quarantine Treatment of Mites, Nematodes and Insects other than Fruit Fly, held in Bangkok, March 1994 also provided further encouragement for expanding the use of irradiation as a quarantine treatment beyond fruit fly infestation

High tracking resolution detectors. Final Technical Report

International Nuclear Information System (INIS)

Vasile, Stefan; Li, Zheng

2010-01-01

High-resolution tracking detectors based on Active Pixel Sensor (APS) have been valuable tools in Nuclear Physics and High-Energy Physics research, and have contributed to major discoveries. Their integration time, radiation length and readout rate is a limiting factor for the planed luminosity upgrades in nuclear and high-energy physics collider-based experiments. The goal of this program was to demonstrate and develop high-gain, high-resolution tracking detector arrays with faster readout, and shorter radiation length than APS arrays. These arrays may operate as direct charged particle detectors or as readouts of high resolution scintillating fiber arrays. During this program, we developed in CMOS large, high-resolution pixel sensor arrays with integrated readout, and reset at pixel level. Their intrinsic gain, high immunity to surface and moisture damage, will allow operating these detectors with minimal packaging/passivation requirements and will result in radiation length superior to APS. In Phase I, we designed and fabricated arrays with calorimetric output capable of sub-pixel resolution and sub-microsecond readout rate. The technical effort was dedicated to detector and readout structure development, performance verification, as well as to radiation damage and damage annealing.

Food irradiation and airline catering

International Nuclear Information System (INIS)

Preston, F.S.

1988-01-01

Food poisoning from contaminated airline food can produce serious consequences for airline crew and passengers and can hazard flight. While irradiation of certain foodstuffs has been practised in a number of countries for some years, application of the process has not been made to complete meals. This paper considers the advantages, technical considerations, costs and possible application to airline meals. In addition, the need to educate the public in the advantages of the process in the wake of incidents such as Chernobyl is discussed

Food irradiation and airline catering.

Science.gov (United States)

Preston, F S

1988-04-01

Food poisoning from contaminated airline food can produce serious consequences for airline crew and passengers and can hazard flight. While irradiation of certain foodstuffs has been practised in a number of countries for some years, application of the process has not been made to complete meals. This paper considers the advantages, technical considerations, costs and possible application to airline meals. In addition, the need to educate the public in the advantages of the process in the wake of incidents such as Chernobyl is discussed.

Food irradiation and airline catering

Energy Technology Data Exchange (ETDEWEB)

Preston, F.S.

1988-04-01

Food poisoning from contaminated airline food can produce serious consequences for airline crew and passengers and can hazard flight. While irradiation of certain foodstuffs has been practised in a number of countries for some years, application of the process has not been made to complete meals. This paper considers the advantages, technical considerations, costs and possible application to airline meals. In addition, the need to educate the public in the advantages of the process in the wake of incidents such as Chernobyl is discussed.

Assessment of repair welding technologies of irradiated materials

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-08-15

Damages of reactor internals of stainless steels caused by SCC and fatigue were identified in aged BWR plants. Repair-welding is one of the practical countermeasure candidates to restore the soundness of components and structures. The project of 'Assessment of Repair welding Technologies of Irradiated Materials' is being carried out to develop the technical guideline regarding the repair-welding of reactor internals. In fiscal 2011, we investigated the weldability of stainless steel 316L irradiated by welding (TIG) tungsten inert gas. Furthermore, the tensile properties and stress corrosion cracking (SCC) susceptibility of the welds were investigated. Cross-sectional observation of heat affected zone (HAZ) of the bead on plate TIG weldments (heat input 4 kJ/cm) of irradiated SUS316L stainless steel containing 0.026 ~ 0.12appm helium showed degradation of grain boundaries due to helium accumulation. Degree of the degradation depended on the amount of helium. No deterioration of grain boundaries was observed by bead on plate welding with one pass one layer when helium content was 0.039appm. The tensile strengths of welds in non-irradiated and irradiated material were similar. However, the elongation of a weldment by irradiated SUS316L containing 0.124appm Helium was lower than non-irradiated. It was estimated to cause the effects of helium bubbles. The SCC susceptibility of the HAZ was no significant difference compared with other locations. (author)

Dynamic rheology behavior of electron beam-irradiated cellulose pulp/NMMO solution

International Nuclear Information System (INIS)

Zhou Ruimin; Deng Bangjun; Hao Xufeng; Zhou Fei; Wu Xinfeng; Chen Yongkang

2008-01-01

The rheological behavior of irradiated cellulose pulp solution by electron beam was investigated. Storage modulus G', loss modulus G'', the dependence of complex viscosity η* and frequency ω of cellulose solutions were measured by DSR-200 Rheometer (Rheometrics co., USA). The molecular weight of irradiated cellulose was measured via the intrinsic viscosity measurement using an Ubbelohde capillary viscometer. The crystalline structure was studied by FTIR Spectroscopy. The results congruously showed that the molecular weight of pulp cellulose decrease and the molecular weight distribution of cellulose become narrow with increase in the irradiation dose. Moreover, the crystalline structure of the cellulose was destroyed, the force of the snarl between the cellulose molecules weakens and the accessibility of pulp spinning is improved. The study supplies some useful data for spinnability of irradiated cellulose and technical data to the filature industry

Expectation and task for constructing the volume reduction system of removed soils. In search of the technical integrity from the intermediate storage to final disposal

International Nuclear Information System (INIS)

Mori, Hisaki

2016-01-01

The intermediate storage volume of the removed soils and incineration ash in Fukushima is supposed about 22 million cubic meters. Within 30 years after starting the intermediate storage, the final disposal outside Fukushima prefecture to these removed soils and incineration ash is determined by the law. Because these removed soils are the very-very low radio activity, the volume reduction method is most effective to reduce the burden of the final disposal. As the volume reduction technology is the stage of research and development, the possibility of the introduction of the volume reduction technology that has the consistency of the final disposal technology is evaluated from the point of view of cost. Since this business is accompanied by economic and technical risk to implement private companies, this project is considered appropriate to be implemented as a national project. (author)

Some legal considerations in the adoption and application of food irradiation technology

Energy Technology Data Exchange (ETDEWEB)

Reyes, L S

1986-12-31

This paper will explore the legislative and administrative measures that a developing country, like the Philippines and other country members of ASEAN, may consider and adopt to safeguard the health and safety of their citizens before allowing the use of food irradiation technology as a means of preserving a variety of foods. Some developed countries are now utilizing radiation in the preservation of some foods for commercial purposes. Also, not all countries importing or exporting irradiated foods are technically capable of determining for themselves whether or not these foods are safe for human consumption. Moreover, irradiated foods may be exported/imported without the authorities knowing it for lack of appropriate labelling or information. In this light, it becomes imperative that consumers be given the assurance that foods preserved through the irradiation process are wholesome and safe. This can only be effectively carried out by governments through the adoption of legislative and administrative measures to ensure the safe utilization of the irradiation process and strict adherence by manufacturers, distributors and sellers of irradiated food to the internationally accepted FAO and WHO standards of irradiated foods and recommended international Code of Practice for operation of radiation facilities for treatment of foods. Some provisions that should be seriously considered in the enactment of legislation include: regulating the utilization of the irradiation process through licensing, i.e. no food item may be irradiated without first securing a license from the appropriate government agency and no irradiated food may be sold or distributed without first securing a similar prior permit/license; providing the specific allowable dose to be utilized in the radiation process beyond which the process will be considered illegal; giving the government the authority to regularly monitor the irradiation facilities to ensure that it is sanitary and technically safe not

Some legal considerations in the adoption and application of food irradiation technology

International Nuclear Information System (INIS)

Reyes, L. S.

1985-01-01

This paper will explore the legislative and administrative measures that a developing country, like the Philippines and other country members of ASEAN, may consider and adopt to safeguard the health and safety of their citizens before allowing the use of food irradiation technology as a means of preserving a variety of foods. Some developed countries are now utilizing radiation in the preservation of some foods for commercial purposes. Also, not all countries importing or exporting irradiated foods are technically capable of determining for themselves whether or not these foods are safe for human consumption. Moreover, irradiated foods may be exported/imported without the authorities knowing it for lack of appropriate labelling or information. In this light, it becomes imperative that consumers be given the assurance that foods preserved through the irradiation process are wholesome and safe. This can only be effectively carried out by governments through the adoption of legislative and administrative measures to ensure the safe utilization of the irradiation process and strict adherence by manufacturers, distributors and sellers of irradiated food to the internationally accepted FAO and WHO standards of irradiated foods and recommended international Code of Practice for operation of radiation facilities for treatment of foods. Some provisions that should be seriously considered in the enactment of legislation include: regulating the utilization of the irradiation process through licensing, i.e. no food item may be irradiated without first securing a license from the appropriate government agency and no irradiated food may be sold or distributed without first securing a similar prior permit/license; providing the specific allowable dose to be utilized in the radiation process beyond which the process will be considered illegal; giving the government the authority to regularly monitor the irradiation facilities to ensure that it is sanitary and technically safe not

Scalable data management, analysis and visualization (SDAV) Institute. Final Scientific/Technical Report

Energy Technology Data Exchange (ETDEWEB)

Geveci, Berk [Kitware, Inc., Clifton Park, NY (United States)

2017-03-28

The purpose of the SDAV institute is to provide tools and expertise in scientific data management, analysis, and visualization to DOE’s application scientists. Our goal is to actively work with application teams to assist them in achieving breakthrough science, and to provide technical solutions in the data management, analysis, and visualization regimes that are broadly used by the computational science community. Over the last 5 years members of our institute worked directly with application scientists and DOE leadership-class facilities to assist them by applying the best tools and technologies at our disposal. We also enhanced our tools based on input from scientists on their needs. Many of the applications we have been working with are based on connections with scientists established in previous years. However, we contacted additional scientists though our outreach activities, as well as engaging application teams running on leading DOE computing systems. Our approach is to employ an evolutionary development and deployment process: first considering the application of existing tools, followed by the customization necessary for each particular application, and then the deployment in real frameworks and infrastructures. The institute is organized into three areas, each with area leaders, who keep track of progress, engagement of application scientists, and results. The areas are: (1) Data Management, (2) Data Analysis, and (3) Visualization. Kitware has been involved in the Visualization area. This report covers Kitware’s contributions over the last 5 years (February 2012 – February 2017). For details on the work performed by the SDAV institute as a whole, please see the SDAV final report.

Effect of Previous Irradiation on Vascular Thrombosis of Microsurgical Anastomosis: A Preclinical Study in Rats

Science.gov (United States)

Gallardo-Calero, Irene; López-Fernández, Alba; Romagosa, Cleofe; Vergés, Ramona; Aguirre-Canyadell, Marius; Soldado, Francisco; Velez, Roberto

2016-01-01

Background: The objective of the present investigation was to compare the effect of neoadjuvant irradiation on the microvascular anastomosis in cervical bundle using an experimental model in rats. Methods: One hundred forty male Sprague–Dawley rats were allocated into 4 groups: group I, control, arterial microanastomosis; group II, control, venous microanastomosis; group III, arterial microanastomosis with previous irradiation (20 Gy); and group IV, venous microanastomosis with previous irradiation (20 Gy). Clinical parameters, technical values of anastomosis, patency, and histopathological parameters were evaluated. Results: Irradiated groups (III and IV) and vein anastomosis groups (II and IV) showed significantly increased technical difficulties. Group IV showed significantly reduced patency rates (7/35) when compared with the control group (0/35). Radiotherapy significantly decreased the patency rates of the vein (7/35) when compared with the artery (1/35). Groups III and IV showed significantly reduced number of endothelial cells and also showed the presence of intimal thickening and adventitial fibrosis as compared with the control group. Conclusion: Neoadjuvant radiotherapy reduces the viability of the venous anastomosis in a preclinical rat model with a significant increase in the incidence of vein thrombosis. PMID:27975009

Decommissioning of an Irradiator MPX-{gamma} - 25M and a neutron Irradiator; Desmantelamiento de un irradiador tipo MPX-{gamma}-25M y de un irradiador de neutrones

Energy Technology Data Exchange (ETDEWEB)

Soguero, Dania; Guerra, Mercedes; Prieto, Enrique; Desdin, Luis, E-mail: sdania@ceaden.edu.cu [Centro de Aplicaciones Tecnologica y Desarrollo Nuclear (CEADEN), La Habana (Cuba)

2013-07-01

In this paper a technology is developed with its procedures in radiation protection to ensure the safety of the process of decommissioning of two irradiators. Both processes are described, the process of decommissioning of a neutron Irradiator 4. 44{center_dot}10{sup 11}Bq, employed in the vegetal radio mutagenesis, and disassembling of an installation of gamma irradiation of 3.33 * 10{sup 12} Bq, self-shielded of category I, model MPX - {gamma} - 25 M. The specific objectives are: a) identify aspects of the contractual assurance, of human and technical resources, b) to evaluate the radiological situation of the process and c) analyze the potential radiological extraordinary events in each of the steps of the process, ensuring the right answers. Evaluation of radiological successful events described can be considered as reference to address the process of disassembling of other similar irradiators.

Medicare and Medicaid programs; salary equivalency guidelines for physical therapy, respiratory therapy, speech language pathology, and occupational therapy services; revised effective date and technical correction--HCFA. Final rule; delay of effective date and correction.

Science.gov (United States)

1998-03-31

This document delays the effective date of the final rule on salary equivalency guidelines, published in the Federal Register (63 FR 5106) on January 30, 1998, from April 1, 1998 to April 10, 1998. In addition, we are making a technical correction in the preamble to the January 30, 1998 final rule.

Project accent: graphite irradiated creep in a materials test reactor

International Nuclear Information System (INIS)

Brooking, M.

2014-01-01

Atkins manages a pioneering programme of irradiation experiments for EDF Energy. One of these projects is Project ACCENT, designed to obtain evidence of a beneficial physical property of the graphite, which may extend the life of the Advanced Gas-cooled Reactors (AGRs). The project team combines the in-house experience of EDF Energy with two supplier organisations (providing the material test reactors and testing facilities) and supporting consultancies (Atkins and an independent technical expert). This paper describes: - Brief summary of the Project; - Discussion of the challenges faced by the Project; and - Conclusion elaborating on the aims of the Project. These challenging experiments use bespoke technology and both un-irradiated (virgin) and irradiated AGR graphite. The results will help to better understand graphite irradiation-induced creep (or stress modified dimensional change) properties and therefore more accurately determine lifetime and safe operating envelopes of the AGRs. The first round of irradiation has been completed, with a second round about to commence. This is a key step to realising the full lifetime ambition for AGRs, demonstrating the relaxation of stresses within the graphite bricks. (authors)

The effect of ionizing irradiation on the postharvest quality of vegetables

International Nuclear Information System (INIS)

Morris, S.C.

1985-01-01

The widespread adoption of irradiation as a postharvest treatment must depend on superior performances with regard to product quality, economics, safety both during application and of the final product, and finally consumer acceptance

Summary of the ITER final design report. July 2001

International Nuclear Information System (INIS)

2001-01-01

This document is a summary of the ITER final design report foreseen during the current, Engineering Design Activities (EDA), phase of the ITER project. The report presents the results of collaborative design and supporting technical work undertaken by the ITER Joint Central team (JCT) and the Home Teams (HT) of the parties to the agreement on co-operation in the Engineering Design Activities for ITER (the ITER EDA Agreement). This report marks the achievement of the full technical scope of activities indicated in the ITER EDA Agreement, with a final design which meets the programmatic objective defined in the Agreement and satisfies detailed scientific, technical and costing objectives set by ITER Council in 1998

Electron trapping during irradiation in reoxidized nitrided oxide

International Nuclear Information System (INIS)

Mallik, A.; Vasi, J.; Chandorkar, A.N.

1993-01-01

Isochronal detrapping experiments have been performed following irradiation under different gate biases in reoxidized nitrided oxide (RNO) MOS capacitors. These show electron trapping by the nitridation-induced electron traps at low oxide fields during irradiation. A difference in the detrapping behavior of trapped holes and electrons is observed, with trapped holes being detrapped at relatively lower temperatures compared to trapped electrons. Electron trapping shows a strong dependence on tile magnitude of the applied gate bias during irradiation but is independent of its polarity. Conventional oxide devices, as expected, do not show any electron trapping during irradiation by the native electron traps. Finally, a comparison of the isochronal detrapping behavior following irradiation and following avalanche injection of electrons has been made to estimate the extent of electron trapping. The results show that electron trapping by the nitridation-induced electron traps does not play the dominant role in improving radiation performance of RNO, though its contribution cannot be completely neglected for low oxide field irradiations

New usable technical specifications

International Nuclear Information System (INIS)

Webster, S.A.; Tomasi, L.T.; Bernier, R.A.

1989-01-01

After 2 yr of preparation, 1988 finally saw the nuclear industry writing operator-oriented technical specifications. This effort is a continuation of previous efforts to develop improved and usable standard technical specifications (STSs), and is being conducted by the four nuclear steam supply system vendor owners' groups under the auspices of the Nuclear Management Resources Council. Each participant is currently preparing a set of improved STSs based on a writer's guide that was developed through a combined industry effort. In May of 1987, a Human Factors Improvements to Technical Specifications (HFITS) task group was formed to prepare a writer's guide for improved, industrywide STSs. This task group was composed of two representatives from each owners' group, one with a human factors background and one with some operations background. Two documents were prepared in 6 months, a human factors report laying the groundwork for the considerations to go into technical specifications and a writer's guide for their preparation. This paper reports on the application of this writer's guide to the writing of improved STS

Detection methods for irradiated foods: current status. Proceedings

International Nuclear Information System (INIS)

McMurray, C.H.; Gray, R.; Stewart, E.M.; Pearce, J.; Queen's Univ., Belfast, Northern Ireland

1996-01-01

This book contains a scientific record of an international meeting on analytical detection methods for irradiation treatment of food. Apart from encouraging the basic development of detection tests, the meeting also aimed to assess the various test methods critically to determine their suitability for general use by public health laboratories and others concerned with trade in irradiated food. Two sets of criteria have been developed to assess test methods, technical criteria for a qualitative or quantitative test and practical criteria if a method is to be widely applied by food labelling authorities. Agreement has already been achieved for the use of electron spin resonance, thermoluminescence, hydrocarbons, 2-Alkylcyclobutanones, microbiological, viscometry and impedance tests. (UK)

TADS Final Evaluation Report, 1980-81. Appendix S.

Science.gov (United States)

Suarez, Tanya M.; And Others

The document contains the final report of the Technical Assistance Development System (TADS), a program which provided technical assistance (TA) services to 53 Handicapped Children's Early Education Program (HCEEP) demonstration projects and 13 State Implementation Grants (SIGs). The evaluation report is divided into five sections. Section 1…

Final report. Geothermal Energy Program: Information dissemination, public outreach, and technical analysis activities. April 1, 1999 to December 31, 2001. USDOE Grant No. DE-FG01-99-EE35098

Energy Technology Data Exchange (ETDEWEB)

Lund, John W.

2002-03-22

This is the final report of the accomplishments of the geothermal energy program: information dissemination, public outreach, and technical analysis activities by the project team consisting of the Geo-Heat Center, Geothermal Resources Council, Geothermal Education Office, Geothermal Energy Association, and the Washington State University Energy Program.

Fifth technical meeting on quality

International Nuclear Information System (INIS)

Girard, A.

1998-01-01

This article reports on the 5th Technical Meeting on Quality which was held in San Diego on 20-22 October 1997 and which was attended by representatives of the Home and Joint Central Team and of manufacturers currently involved in the Large R and D projects. The meeting made progress towards the finalization of the ITER Quality Manual document for inclusion in the Final Design Report and the definition of the quality necessary for ITER procurement and construction

Functional criteria for emergency response facilities. Technical report (final)

International Nuclear Information System (INIS)

1981-02-01

This report describes the facilities and systems to be used by nuclear power plant licensees to improve responses to emergency situations. The facilities include the Technical Support Center (TSC), Onsite Operational Support Center (OSC), and Nearsite Emergency Operations Facility (EOF), as well as a brief discussion of the emergency response function of the control room. The data systems described are the Safety Parameter Display System (SPDS) and Nuclear Data Link (NDL). Together, these facilities and systems make up the total Emergency Response Facilities (ERFs). Licensees should follow the guidance provided both in this report and in NUREG-0654 (FEMA-REP-1), Revision 1, for design and implementation of the ERFs

Latin American regional co-operative programme on food irradiation

International Nuclear Information System (INIS)

1992-06-01

The ''Latin American Regional Co-ordinated Research Programme on Food Irradiation'' was established in 1986 with the participation of research scientists from countries in the region to investigate the efficacy of food irradiation as a treatment to reduce post-harvest losses and improve the hygienic quality of food, to conduct techno-economic feasibility studies, and to disseminate knowledge about the scientific, health, legal and commercial aspects of food irradiation. This publication contains the final report of the Co-ordinated Research Programme and summaries of individual research reports presented by the participating scientists

Research and materials irradiation reactors

International Nuclear Information System (INIS)

Ballagny, A.; Guigon, B.

2004-01-01

Devoted to the fundamental and applied research on materials irradiation, research reactors are nuclear installations where high neutrons flux are maintained. After a general presentation of the research reactors in the world and more specifically in France, this document presents the heavy water cooled reactors and the water cooled reactors. The third part explains the technical characteristics, thermal power, neutron flux, operating and details the Osiris, the RHF (high flux reactor), the Orphee and the Jules Horowitz reactors. The last part deals with the possible utilizations. (A.L.B.)

Heritable Genetic Changes in Cells Recovered From Irradiated 3D Tissue Contracts. Final report

Energy Technology Data Exchange (ETDEWEB)

Cornforth, Michael N. [The University of Texas Medical Branch at Galveston, TX (United States)

2013-05-03

Combining contemporary cytogenetic methods with DNA CGH microarray technology and chromosome flow-sorting increases substantially the ability to resolve exchange breakpoints associated with interstitial deletions and translocations, allowing the consequences of radiation damage to be directly measured at low doses, while also providing valuable insights into molecular mechanisms of misrepair processes that, in turn, identify appropriate biophysical models of risk at low doses. The aims of this work apply to cells recovered from 3D tissue constructs of human skin and, for the purpose of comparison, the same cells irradiated in traditional 2D cultures. These aims are: to analyze by multi-flour fluorescence in situ hybridization (mFISH) the chromosomes in clonal descendents of individual human fibroblasts that were previously irradiated; to examine irradiated clones from Aim 1 for submicroscopic deletions by subjecting their DNA to comparative genomic hybridization (CGH) microarray analysis; and to flow-sort aberrant chromosomes from clones containing stable radiation-induced translocations and map the breakpoints to within an average resolution of 100 kb using the technique of 'array painting'.

Heritable Genetic Changes in Cells Recovered From Irradiated 3D Tissue Contracts. Final report

International Nuclear Information System (INIS)

Cornforth, Michael N.

2013-01-01

Combining contemporary cytogenetic methods with DNA CGH microarray technology and chromosome flow-sorting increases substantially the ability to resolve exchange breakpoints associated with interstitial deletions and translocations, allowing the consequences of radiation damage to be directly measured at low doses, while also providing valuable insights into molecular mechanisms of misrepair processes that, in turn, identify appropriate biophysical models of risk at low doses. The aims of this work apply to cells recovered from 3D tissue constructs of human skin and, for the purpose of comparison, the same cells irradiated in traditional 2D cultures. These aims are: to analyze by multi-flour fluorescence in situ hybridization (mFISH) the chromosomes in clonal descendents of individual human fibroblasts that were previously irradiated; to examine irradiated clones from Aim 1 for submicroscopic deletions by subjecting their DNA to comparative genomic hybridization (CGH) microarray analysis; and to flow-sort aberrant chromosomes from clones containing stable radiation-induced translocations and map the breakpoints to within an average resolution of 100 kb using the technique of 'array painting'

Feasibility analysis of a sewage sludge treatment by an irradiation plant in Mexico

CERN Document Server

Moreno, J; Colin, A; Tavera, L

2002-01-01

Technical and economic analyses of an irradiation plant for sewage sludge treatment determined that an appropriate place for the first sludge electron irradiator in Mexico would be the sewage water treatment plant located north of Toluca in the State of Mexico. This treatment plant is mainly used for domestic wastewater and produces an approximate volume of 70 ton d-] liquid sewage sludge. Considering a 50 k W power of a 10 MeV electron linear accelerator, an irradiation dose of S KGy and a treatment capacity of 346 tons per day, it is estimated that the treatment cost would be of $9.00 US dollars per ton. (Author)

Economic feasibility of food irradiation in the Philippines

International Nuclear Information System (INIS)

Singson, C.C.; De Guzman, Z.M.; Pasion, W.B.

1991-01-01

Food irradiation is not a new technology and is accepted in many countries. Market acceptance of irradiated foods is established and the importance of radiation to reduce post-harvest food losses, increase shelf-life and improve hygienic quality of foods has been recognized in Asia and the Pacific. Countries with strict quarantine restrictions, such as the United States and Japan, require treatment of fresh fruits and produce for insect pests disinfestation. Several studies have established the technical feasibility of using radiation to preserve some food items in the country such as mangoes, onions, garlic, black pepper, coffee, prawns and desiccated coconut. The aim of this study is to determine the feasibility of setting up an irradiation facility in the Philippines, to undertake the processing of selected food items especially those with good export potentials, to identify areas of concern vital to the success or failure of this type of undertaking and to make recommendations to enhance the viability of this project. (auth.). 13 refs.; appendices; 6 tabs

Thyroid gland irradiations and thyroid cancers; Critical bibliographic journal; Irradiations de la thyroide et cancers thyroidiens. Revue bibliographique critique

Energy Technology Data Exchange (ETDEWEB)

Vitauxa, F. [CHI Le Raincy-Montfermeil, Faculte X. Bichat, Lab. de Biophysique, Service de Medecine Nucleaire, 93 - Le Raincy-Montfermeil (France)

2007-07-15

The large increase in the incidence of thyroid cancer among children who were mainly less than five years old at the time of the Chernobyl accident is still a major concern for endocrinologists and nuclear medicine physicians. Epidemiological studies have focused solely on iodine-131. However, past knowledge on thyroid irradiation (medical use of iodine-131, radioactive fallout on Marshall islands and the Nevada and Hanford site releases) as well as number of recent works (about low-dose irradiation) raise question on the role of other factors. It is here shown that post-Chernobyl thyroid irradiation is complex and that all factors (iodine-131, but also short lived isotopes of iodine and external irradiation) should be considered. Finally, one needs to think about some of the present medical uses of iodine-131 and especially to the treatment of hyperthyroidism in young subjects. (author)

International standards and agreements in food irradiation

International Nuclear Information System (INIS)

Cetinkaya, N.

2004-01-01

Full text: The economies of both developed and developing countries have been effected by their exported food and agricultural products. Trading policies of food and agricultural products are governed by international agreement as well as national regulations. Trade in food and agricultural commodities may be affected by both principal Agreements within the overall World Trade Organization (WTO) Agreement, though neither specifically refers to irradiation or irradiated foods. The principal Agreements are the Technical Barriers to Trade (TBT) Agreement and the Sanitary and Phyto sanitary (SPS) Agreement. The SPS of the WTO requires governments to harmonize their sanitary and phyto sanitary measures on as wide basis as possible. Related standards, guidelines and recommendations of international standard setting bodies such as the Codex Alimentarius Commission (food safety); the International Plant Protection Convention (IPPC) (plant health and quarantine); and International Office of Epizootic (animal health and zoo noses) should be used in such a harmonization. International Standards for Phyto sanitary Measures (ISPM) no.18 was published under the IPPC by FAO (April 2003, Rome-Italy). ISPM standard provides technical guidance on the specific procedure for the application of ionizing radiation as a phyto sanitary treatment for regulated pests or articles. Moreover, Codex Alimentarius Commission, Codex General Standard for Irradiated Foods (Stand 106-1983) and Recommended International Code of Practice were first published in 1983 and revised in March 2003. Scope of this standard applies to foods processed by ionizing radiation that is used in conjunction with applicable hygienic codes, food standards and transportation codes. It does not apply to foods exposed to doses imparted by measuring instruments used for inspection purposes. Codex documents on Principles and Guidelines for the Import/Export Inspection and Certification of Foods have been prepared to guide

Dismantling of Irradiation Facility Selfshielded of Investigation Model MPX- γ-25M

International Nuclear Information System (INIS)

Soguero, D.; Rapado, M.; Prieto, E.; Desdin, L.; Guerra, M.; Castillo, J.

2011-01-01

In this paper is described the dismantling a category I selfshielded gamma irradiation facility model MPX - γ - 25M. The following specific objectives were established: a) identify aspects of the insurance contract, human and technical resources b) assess the radiological situation of the process and c) analyze potential radiological extraordinary events in each step of the process, ensuring appropriate responses, based on an evaluation of process safety. The assessment of radiological events can serve as a reference for addressing the process of dismantling other similar irradiators. (Author)

New irradiation facilities at the Australian national medical cyclotron

International Nuclear Information System (INIS)

Parcell, S.K.; Arnott, D.W.; Conard, E.M.

1999-01-01

Two new irradiation facilities have been developed at the National Medical Cyclotron for radionuclide production. The first relocates PET irradiations from the cyclotron vault to a dedicated PET beam room, to improve accessibility and reduce radiation exposures associated with target maintenance. This new facility consists of a beam line to transport 16-30 MeV proton beams from the cyclotron to 1 of 8 PET targets mounted on a target rack. The target rack has increased the number of targets available for production and experimentation. The second is a completely independent solid target irradiation facility for SPECT. This facility consists of a beam line to transport 26-30 MeV proton beams from the cyclotron to a dedicated beam room containing one solid target station. A new pneumatic target transfer system was also developed to transport the solid target to and from the existing chemistry hot cells. The beam line and target components are operated under the control of a dedicated PLC with a PC based user interface. The development and some technical aspects of these new irradiation facilities are discussed here. (author)

Final Technical Report for Award DESC0011912, "Trimodal Tapping Mode Atomic Force Microscopy: Simultaneous 4D Mapping of Conservative and Dissipative Probe-Sample Interactions of Energy-Relevant Materials”

Energy Technology Data Exchange (ETDEWEB)

Solares, Santiago D. [George Washington Univ., Washington, DC (United States)

2017-09-22

The final project report covering the period 7/1/14-6/30/17 provides an overview of the technical accomplishments in the areas of (i) fundamental viscoelasticity, (ii) multifrequency atomic force microscopy, and (iii) characterization of energy-relevant materials with atomic force microscopy. A list of publications supported by the project is also provided.

The role of non-technical skills in surgery.

Science.gov (United States)

Agha, Riaz A; Fowler, Alexander J; Sevdalis, Nick

2015-12-01

Non-technical skills are of increasing importance in surgery and surgical training. A traditional focus on technical skills acquisition and competence is no longer enough for the delivery of a modern, safe surgical practice. This review discusses the importance of non-technical skills and the values that underpin successful modern surgical practice. This narrative review used a number of sources including written and online, there was no specific search strategy of defined databases. Modern surgical practice requires; technical and non-technical skills, evidence-based practice, an emphasis on lifelong learning, monitoring of outcomes and a supportive institutional and health service framework. Finally these requirements need to be combined with a number of personal and professional values including integrity, professionalism and compassionate, patient-centred care.

The role of non-technical skills in surgery

Science.gov (United States)

Agha, Riaz A.; Fowler, Alexander J.; Sevdalis, Nick

2015-01-01

Non-technical skills are of increasing importance in surgery and surgical training. A traditional focus on technical skills acquisition and competence is no longer enough for the delivery of a modern, safe surgical practice. This review discusses the importance of non-technical skills and the values that underpin successful modern surgical practice. This narrative review used a number of sources including written and online, there was no specific search strategy of defined databases. Modern surgical practice requires; technical and non-technical skills, evidence-based practice, an emphasis on lifelong learning, monitoring of outcomes and a supportive institutional and health service framework. Finally these requirements need to be combined with a number of personal and professional values including integrity, professionalism and compassionate, patient-centred care. PMID:26904193

Food irradiation: A technique for preserving and improving the safety of food

International Nuclear Information System (INIS)

1988-01-01

Processing of food with low levels of radiation has the potential to contribute to reducing both spoilage of food during storage - a particular problem in developing countries - and the high incidence of food-borne disease currently seen in all countries. Approval has been granted for the treatment of more than 30 products with radiation in over 30 countries but, in general, governments have been slow to authorize the use of this new technique. One reason for this slowness is a lack of understanding of what food irradiation entails. This book aims to increase understanding by providing information on the process of food irradiation in simple, non-technical language. It describes the effects that irradiation has on food, and the plant and equipment that are necessary to carry it out safely. The legislation and control mechanisms required to ensure the safety of food irradiation facilities are also discussed. Education is seen as the key to gaining the confidence of the consumers in the safety of irradiated food, and to promoting understanding of the benefits that irradiation can provide

Food irradiation: A technique for preserving and improving the safety of food

International Nuclear Information System (INIS)

1992-01-01

Processing of food with low levels of radiation has the potential to contribute to reducing both spoilage of food during storage - a particular problem in developing countries - and the high incidence of food-borne disease currently seen in all countries. Approval has been granted for the treatment of more than 30 products with radiation in over 30 countries but, in general , governments have been slow to authorize the use of this new technique. One reason for this slowness is a lack of understanding of what food irradiation entails. This book aims to increase understanding by providing information on the process of food irradiation in simple, non-technical language. It describes the effects that irradiation has on food , and the plant and equipment that are necessary to carry it out safely. The legislation and control mechanisms required to ensure the safety of food irradiation facilities are also discussed. Education is seen as the key to gaining the confidence of the consumers in the safety of irradiated food, and to promoting understanding of the benefits that irradiation can provide

Final Technical Report - SciDAC Cooperative Agreement: Center for Wave Interactions with Magnetohydrodynamics

International Nuclear Information System (INIS)

Schnack, Dalton D.

2012-01-01

Final technical report for research performed by Dr. Thomas G. Jenkins in collaboration with Professor Dalton D. Schnack on SciDAC Cooperative Agreement: Center for Wave Interactions with Magnetohydrodyanics, DE-FC02-06ER54899, for the period of 8/15/06 - 8/14/11. This report centers on the Slow MHD physics campaign work performed by Dr. Jenkins while at UW-Madison and then at Tech-X Corporation. To make progress on the problem of RF induced currents affect magnetic island evolution in toroidal plasmas, a set of research approaches are outlined. Three approaches can be addressed in parallel. These are: (1) Analytically prescribed additional term in Ohm's law to model the effect of localized ECCD current drive; (2) Introduce an additional evolution equation for the Ohm's law source term. Establish a RF source 'box' where information from the RF code couples to the fluid evolution; and (3) Carry out a more rigorous analytic calculation treating the additional RF terms in a closure problem. These approaches rely on the necessity of reinvigorating the computation modeling efforts of resistive and neoclassical tearing modes with present day versions of the numerical tools. For the RF community, the relevant action item is - RF ray tracing codes need to be modified so that general three-dimensional spatial information can be obtained. Further, interface efforts between the two codes require work as well as an assessment as to the numerical stability properties of the procedures to be used.

Where's the beef? An update on meat irradiation in the USA

International Nuclear Information System (INIS)

Adams, Patterson

2000-01-01

Since the US Food and Drug Administration (FDA) approved irradiation of red meats in December 1997, the irradiation industry has been focused on this potential new utilization of our technology. In February 1999, the United States Department of Agricultural (USDA) finally issued a proposed rule, which will allow processors to begin irradiating red meats for human consumption. This presentation provides a brief update of the rules, regulations and prospects for this promising application. (author)

Some UK experience and practice in the packaging and transport of irradiated fuel

International Nuclear Information System (INIS)

Edney, C.J.; Rutter, R.L.

1977-01-01

The origin and growth of irradiated fuel transport within and to the U.K. is described and the role of the organisations presently carrying out transport operations is explained. An explanation of the relevant U.K. regulations and laws affecting irradiated fuel transport and the role of the controlling body, the Department of the Environment is given. An explanation is given of the technical requirements for the transport of irradiated Magnox fuel and of the type of flask used, and the transport arrangements, both within the U.K. and to the U.K., from overseas is discussed. The technical requirements for the transport of C.A.G.R. fuel are outlined and the flask and transport arrangements are discussed. The transport requirements of oxide fuel from water reactors is outlined and the flask and shipping arrangements under which this fuel is brought to the U.K. from overseas is explained. The shipping arrangements are explained with particular reference to current international and national requirements. The requirements of the transport of M.T.R. fuel are discussed and the flask type explained. The expected future expansion of the transport of irradiated fuel within and to the U.K. is outlined and the proposed operating methods are briefly discussed. A summary is given of the U.K. experience and the lessons to be drawn from that experience

Study on the promotion of international cooperation through the technical exhibition on RI production and application

Energy Technology Data Exchange (ETDEWEB)

Park, Kyung Bae; Hong, Y D; Han, H S. and others

2001-05-01

For the IAEA Technical Exhibition, it was required to analyze the all the informations from the researches which has been done till recently related to the applications of radiation and radioisotopes. A few aspects drawn from the analysis were made and it was able to represent the scopes and the prospects regarding the applications of radiation and radioisotopes developed in Korea at the IAEA Technical Exhibition. Exhibition was mainly focus into the RI production, utilization in medical, engineering and agricultural fields and irradiation of food products. Exhibition representing Korea were readily prepared under the entitled name of 'Pillars for Quality of Life', Multi-cube and Panel presentation at the same time. IAEA Technical Exhibition was held from September 18 to 21, 2000. Exhibition was successfully proceeded and presentation led to get the attention from IAEA Member Counturies including developed and developing countries about Korea's recent development on improving quality of human life using radiation and radioisotopes. The outcome of IAEA Technical Exhibition prepared by based on the successful experiences and activity related to the subjects was primarily on the elucidation of international cooperation between Korea and foreign countries. Multi-cube and Panel presentation expressed fully and effectively the scopes of the researches recently undergone in Korea and the efforts put into the technical development on radiation and radioisotopes application. In addition, other important research results were provided by Leaflet and those were about 'Radioisotope Production', 'Application of Radioisotope Tracers', 'Wastewater Treatment by Irradiation' and 'Food Irradiation'. All the exhibition materials including Compact Diskette were prepared in English for the IAEA Technical Exhibition held in Austria Center Vienna during the 44th IAEA General Conference. The reported informations and materials should be employed to the other objectives like presentation

Study on the promotion of international cooperation through the technical exhibition on RI production and application

International Nuclear Information System (INIS)

Park, Kyung Bae; Hong, Y. D.; Han, H. S. and others

2001-05-01

For the IAEA Technical Exhibition, it was required to analyze the all the informations from the researches which has been done till recently related to the applications of radiation and radioisotopes. A few aspects drawn from the analysis were made and it was able to represent the scopes and the prospects regarding the applications of radiation and radioisotopes developed in Korea at the IAEA Technical Exhibition. Exhibition was mainly focus into the RI production, utilization in medical, engineering and agricultural fields and irradiation of food products. Exhibition representing Korea were readily prepared under the entitled name of 'Pillars for Quality of Life', Multi-cube and Panel presentation at the same time. IAEA Technical Exhibition was held from September 18 to 21, 2000. Exhibition was successfully proceeded and presentation led to get the attention from IAEA Member Counturies including developed and developing countries about Korea's recent development on improving quality of human life using radiation and radioisotopes. The outcome of IAEA Technical Exhibition prepared by based on the successful experiences and activity related to the subjects was primarily on the elucidation of international cooperation between Korea and foreign countries. Multi-cube and Panel presentation expressed fully and effectively the scopes of the researches recently undergone in Korea and the efforts put into the technical development on radiation and radioisotopes application. In addition, other important research results were provided by Leaflet and those were about 'Radioisotope Production', 'Application of Radioisotope Tracers', 'Wastewater Treatment by Irradiation' and 'Food Irradiation'. All the exhibition materials including Compact Diskette were prepared in English for the IAEA Technical Exhibition held in Austria Center Vienna during the 44th IAEA General Conference. The reported informations and materials should be employed to the other objectives like presentation

IRRSUD Project - Final report

CERN Document Server

Loyer, F

2002-01-01

IRRSUD is an irradiation facility which makes use of the low energy (0.5 MeV/n - 1 MeV/n) beams from the GANIL IRRSUD injectors. It is financed by the group GARI (Group of Ion Research Applications) and was established as a joint-venture of GANIL and CIRIL to develop the applied physics and ion based industrial applications. Among research directions framed by IRRSUD one can mention; the nano-technologies i.e. utilisation of the modifications induced in materials exposed to ion bombardment; realization of microporous membranes and low-D materials; aging of materials by irradiation. Also, the low energy ions issued from the injector matches very well the fission fragments in reactors. In addition IRRSUD could be used as testing facility for injectors.. The report is structured as follows: 1. Outline; 1.2. Project's main features; 1.3. Ion beam characterization; 2. Technical solutions; 2.1. Denominations; 2.2. Beam optics; 2.3. Beam bending magnets; 2.4. Beam instrumentation; 2.5. Current supply; 2.6. Vacuum sy...

AIPM Final Report

Energy Technology Data Exchange (ETDEWEB)

John Mookken

2006-06-30

The final AIPM project report consists of six sections. Each section includes information on the original AIPM project and extension work on the high temperature design. The first section (1) provides an overview of the program and highlights the significant targets to meet at the end of the program. The next section (2) summarizes the significant technical accomplishments by the SEMIKRON AIPM team during the course of the project. Greater technical details are provided in a collection of all the quarterly reports which can be found in the appendix. Section three (3) presents some the more significant technical data collected from technology demonstrators. Section four (4) analyzes the manufacturing cost or economic aspects of producing 100,000 units/yr. Section five (5) describes the commercialization efforts of the AIPM technology into the automotive market. The last section (6) recommends follow on work that will build on the efforts and achievements of the AIPM program.

ITER technical advisory committee meeting

International Nuclear Information System (INIS)

Fujiwara, M.

2001-01-01

The 17th Meeting of the ITER Technical Advisory Committee (TAC-17) was held on February 19-22, the ITER Garching Work Site in Germany. The objective of the meeting was to review the Draft Final Design Report of ITER-FEAT and assess the ability of the self-consistent overall design both to satisfy the technical objectives previously defined and to meet the cost limitations. TAC-17 was also organized to confirm that the design and critical elements, with emphasis on the key recommendations made at previous TAC meetings, are such as to extend the confidence in starting ITER construction. It was also intended to provide the ITER Council, scheduled to meet on 27 and 28 February in Toronto, with a technical assessment and key recommendations of the above mentioned report

Technical specification improvements to containment heat removal and emergency core cooling systems: Final report

International Nuclear Information System (INIS)

Sullivan, W.P.; Ha, C.; Pentzien, D.C.; Visweswaran, S.

1988-07-01

This report presents the results of an analysis for technical specification improvements to the emergency core cooling systems (ECCS) and containment heat removal systems (EPRI Research Project 2142-3). The objective of this project is to further develop a reliability- and risk-based methodology to provide improvements by considering groups of surveillance test intervals and allowed out-of-service times jointly. This was done for the technical specifications for the ECCS, containment heat removal equipment, and supporting systems of a boiling water reactor plant. The project (1) developed a methodology for optimizing groups of surveillance test intervals and allowed out-of-service times jointly, (2) applied the methodology in a case study of a specific operating plant, Hatch-2, and (3) evaluated benefits of the application. The results of the case study demonstrate that beneficial technical specification improvements can be realized with application of the methodology. By tightening a small group of sensitive surveillance test intervals (STIs) and allowed out-of-service times (AOTs), a larger group of less sensitive STIs and AOTs can be extended resulting in an overall plant operating cost improvement without reducing the plant safety. The reliability- and risk-based methodology and results from this project can be effectively applied for technical specification improvements at other operating plants

ITER EDA technical activities

International Nuclear Information System (INIS)

Aymar, R.

1998-01-01

Six years of technical work under the ITER EDA Agreement have resulted in a design which constitutes a complete description of the ITER device and of its auxiliary systems and facilities. The ITER Council commented that the Final Design Report provides the first comprehensive design of a fusion reactor based on well established physics and technology

Capital and operating costs of irradiated natural uranium reprocessing plants; Couts d'investissement et d'exploitation des usines de retraitement de l'uranium naturel irradie

Energy Technology Data Exchange (ETDEWEB)

Thiriet, L; Jouannaud, C; Couture, J; Duboz, J [Commissariat a l' Energie Atomique (France). Centre d' Etudes Nucleaires; Oger, C [Saint Gobain Nucleaire (France)

1966-07-01

This paper presents first a method of analysing natural uranium reprocessing plants investment costs (method similar to LANG and BACH well known in the fuel oil industry) and their operating costs (analysed according to their economic type). This method helps establishing standard cost structures for these plants, allowing thus comparisons between existing or planned industrial facilities. It also helps evaluating the foreseeable consequences of technical progress. Some results obtained are given, concerning: the investment costs sensitivity to the various technical parameters defining the fuel and their comparison according to the country or the economic area taken into account. Finally, the influence of the plants size on their investment costs is shown. (author) [French] La communication expose d'abord une methode d'analyse des couts d'investissement des usines de retraitement de l'uranium naturel irradie (inspiree de celles de LANG et de BACH, bien connues dans l'industrie petroliere) et de leurs couts d'exploitation (selon leur nature economique). Cette methode permet d'etablir des structures types de couts de ces usines et de comparer les realisations industrielles et les projets. Elle facilite l'exploration des consequences previsibles du progres technique. On indique un certain nombre de resultats obtenus, concernant la sensibilite des couts d'investissement de ces usines aux differents parametres techniques definissant le combustible et leur confrontation selon les pays ou aires economiques envisages. On montre enfin comment doit pouvoir s'exprimer l'influence de la taille des usines sur leur cout d'investissement. (auteur)

DOE Utility Matching Program Final Technical Report

International Nuclear Information System (INIS)

Haghighat, Alireza

2002-01-01

This is the Final report for the DOE Match Grant (DE-FG02-99NE38163) awarded to the Nuclear and Radiological Engineering (NRE) Department, University of Florida, for the period of September 1999 to January 2002. This grant has been instrumental for maintaining high-quality graduate and undergraduate education at the NRE department. The grant has been used for supporting student entry and retention and for upgrading nuclear educational facilities, nuclear instrumentation, computer facilities, and computer codes to better enable the incorporation of experimental experiences and computer simulations related to advanced light water fission reactor engineering and other advanced reactor concepts into the nuclear engineering course curricula

Economic study for the establishment of A food irradiation facility at port said harbour

International Nuclear Information System (INIS)

EL-Gameel, E.A.

2004-01-01

The present study discusses the economic aspects of establishing food irradiation facility at Port Said harbour and the effect of various parameters on the unit processing costs. The study is concerned with carrying out an economic evaluation for the application of food exports from Port Said harbour and the marketing and technical aspects where the suitable commodity mix has been determined for the agricultural crops which were proposed for irradiation. The investment criteria utilized for commercial evaluation were internal rate of return (IRR) and pay back period (PEP). The irradiation cost and the additional income are also discussed. The results of this analysis showed that the establishment of food irradiation unit in Port Said harbour in Egypt would be economically feasible

Food Irradiation Newsletter. V. 10, no. 2

International Nuclear Information System (INIS)

1986-11-01

This issue reports the summary of the Task Force Meeting on the Use of Irradiation to Ensure Hygienic Quality of Food, convened by the International Consultative Group on Food Irradiation (ICGFI) in Vienna, July 1986. The full report of the final FAO/IAEA Research Co-ordination Meeting on Factors Influencing the Utilization of Food Irradiation, convened in Dubrovnik, Yugoslavia in June 1986, contains the conclusion of the work carried out under the Co-ordinated Research Programme in the past 5 years. A Regional Co-ordinated Research Programme for Latin America has been launched with a workshop convened on this subject in Piracicaba, Brazil, July 1986. Also featured is the summary report of the FAO/IAEA Seminar for Asia and the Pacific on the Practical Application of Food Irradiation convened in Shanghai, People's Republic of China, April 1986. The well-attended seminar reported on the progress and development of practical scale application of food irradiation in the region. A successful market testing of irradiated mangoes in Miami, Florida is also described. The outcome of this test is quite significant in view of the Chernobyl accident a few months before the tests. Tabs

Status and development of food irradiation technology in Korea

International Nuclear Information System (INIS)

Byun, Myungwoo; Park, Younnam

1996-01-01

In Korea, the health authorities and food industry emphasize the need of sanitary food production, which is mainly resulted from the recent growing of consumer's interest in the safety of food. For that reason, development of a new alternative technology of chemicals currently used for decontamination and disinfestation has become an urgent task in the domestic and worldwide food industry. Furthermore, the improvement of quality and manufacturing process of processed foods is a requisite for winning the competition in export fields. Irradiation technology being practically applicable in the food industry has been well established on the basis of more than 40 years of R and D work in the fields of the increasing availability of food-stuffs, sanitary food production and quarantine treatment in a food trade. The wholesomeness of irradiated foods has been officially approved in 37 countries, of which 25 countries are commercially utilizing food irradiation technology. The first commercial irradiator in Korea (18.5 PBq : 500 kCi 60 Co, max. cap ; 4 MCi) was established at Kyungki-do, Yeoju-gun by Greenpia Tech. Inc. with the technical assistance of Korea Atomic Energy Research Institute in June 1987. As of 1996, thirteen irradiated food groups (above 25 items) have been domestically approved for human consumption and an industrial irradiation facility is also available. However, the promotion of consumer acceptance toward irradiated foods is considered as a confronted subject to be studied for a commercial utilization of this technology

Vadose zone microbial community structure and activity in metal/radionuclide contaminated sediments. Final technical report

Energy Technology Data Exchange (ETDEWEB)

Balkwill, David L.

2002-08-17

This final technical report describes the research carried out during the final two months of the no-cost extension ending 11/14/01. The primary goals of the project were (1) to determine the potential for transformation of Cr(VI) (oxidized, mobile) to Cr(III) (reduced, immobile) under unsaturated conditions as a function of different levels and combinations of (a) chromium, (b) nitrate (co-disposed with Cr), and (c) molasses (inexpensive bioremediation substrate), and (2) to determine population structure and activity in experimental treatments by characterization of the microbial community by signature biomarker analysis and by RT-PCR and terminal restriction fragment length polymorphism (T-RFLP) and 16S ribosomal RNA genes. It was determined early in the one-year no-cost extension period that the T-RFLP approach was problematic in regard to providing information on the identities of microorganisms in the samples examined. As a result, it could not provide the detailed information on microbial community structure that was needed to assess the effects of treatments with chromium, nitrate, and/or molasses. Therefore, we decided to obtain the desired information by amplifying (using TR-PCR, with the same primers used for T-RFLP) and cloning 16S rRNA gene sequences from the same RNA extracts that were used for T-RFLP analysis. We also decided to use a restriction enzyme digest procedure (fingerprinting procedure) to place the clones into types. The primary focus of the research carried out during this report period was twofold: (a) to complete the sequencing of the clones, and (b) to analyze the clone sequences phylogenetically in order to determine the relatedness of the bacteria detected in the samples to each other and to previously described genera and species.

Irradiated test fuel shipment plan for the LWR MOX fuel irradiation test project

International Nuclear Information System (INIS)

Shappert, L.B.; Dickerson, L.S.; Ludwig, S.B.

1998-01-01

This document outlines the responsibilities of DOE, DOE contractors, the commercial carrier, and other organizations participating in a shipping campaign of irradiated test specimen capsules containing mixed-oxide (MOX) fuel from the Idaho National Engineering and Environmental Laboratory (INEEL) to the Oak Ridge National Laboratory (ORNL). The shipments described here will be conducted according to applicable regulations of the US Department of Transportation (DOT), US Nuclear Regulatory Commission (NRC), and all applicable DOE Orders. This Irradiated Test Fuel Shipment Plan for the LWR MOX Fuel Irradiation Test Project addresses the shipments of a small number of irradiated test specimen capsules and has been reviewed and agreed to by INEEL and ORNL (as participants in the shipment campaign). Minor refinements to data entries in this plan, such as actual shipment dates, exact quantities and characteristics of materials to be shipped, and final approved shipment routing, will be communicated between the shipper, receiver, and carrier, as needed, using faxes, e-mail, official shipping papers, or other backup documents (e.g., shipment safety evaluations). Any major changes in responsibilities or data beyond refinements of dates and quantities of material will be prepared as additional revisions to this document and will undergo a full review and approval cycle

Analysis Of Irradiated Spices In Uruguay

International Nuclear Information System (INIS)

Montalban, Antonio; Abreu, Anibal V.

1999-01-01

This paper considered the benefit evaluation of the Irradiation processing for the spices within of our regional market .The objective was to raise the competitive of the point of view of quality . There are same problems for the use spices in food, because they are normally with a load of microorganisms , principally in the elaboration of food prepared and sausages. This study analyzed the irradiation for decontamination of spices at a dose level of 10 Kgy in comparison with unirradiated products. It was elected different types of spices and producers , and evaluated the final results to the local market

Analysis of spices irradiated in Uruguay

International Nuclear Information System (INIS)

Montalban, Antonio; Abreu, Anibal

1999-01-01

This paper considered the benefit evaluation of the irradiation processing for the spices within of our regional market .the objective was to raise the competitive of the point of view of quality .There are same problems for the use spices in food, because they are normally with a load of microorganisms , principally in the elaboration of food prepared and sausages.This study analyzed the irradiation for decontamination of spices at a dose level of 10 kgy in comparison with unirradiated products. It was elected different types of spices and producers, and evaluated the final results to the local market

Technical-tactical analysis of youth olympic taekwondo combat.

Science.gov (United States)

Tornello, Francesco; Capranica, Laura; Minganti, Carlo; Chiodo, Salvatore; Condello, Giancarlo; Tessitore, Antonio

2014-04-01

The purpose of this study was to define the technical and tactical profiles of official youth taekwondo competitions played under the most recent rules of the International Taekwondo Federation. Tactical actions (i.e., attack, defense, and block), technical executions (from 1- to 4-point scores), kicking legs (i.e., front/rear and right/left), and overall technical effectiveness were investigated in relation to match outcome of semifinal and final competitions (n = 50) of youth (aged 13-14 years) black belt athletes during the Italian Taekwondo Cadet Championship. Differences (p technical exchanges showed differences (p technical executions. Winners resulted more efficient (p technical and tactical variables. In general, these findings showed that Cadets tend to adopt an offensive strategy. In considering that the adoption of the new electronic system requires athletes to execute correct technical actions to have a score assigned, coaches should emphasize the effectiveness of scoring techniques and help athletes to effectively improve their defense and counterattack capabilities.

DNA-repair after irradiation of cells with gamma-rays and neutrons

International Nuclear Information System (INIS)

Altmann, H.

1975-11-01

The structural alterations of calf thymus DNA produced by neutron or gamma irradiation were observed by absorption spectra, sedimentation rate and viscosity measurements. Mixed neutron-gamma irradiation produced fewer single and double strand breaks compared with pure gamma irradiation. RBE-values for mixed neutron-gamma radiation were less than 1, and DNA damage decreased with increasing neutron dose rate. Repair processes of DNA occuring after irradiation were measured in mouse spleen suspensions and human lymphocytes using autoradiographic methods and gradient centrifugations. The number of labelled cells was smaller after mixed neutron-gamma irradiation than after gamma irradiation. The rejoining of strand breaks in alkaline and neutral sucrose was more efficient after gamma irradiation than after mixed neutron-gamma irradiation. Finally, the effect of detergents Tween 80 and Nonident P40 on unscheduled DNA synthesis was studied by autoradiography after mixed neutron-gamma irradiation (Dn=5 krad). The results showed that the DNA synthesis was inhibited by detergent solutions of 0.002%

Forecast Method of Solar Irradiance with Just-In-Time Modeling

Science.gov (United States)

Suzuki, Takanobu; Goto, Yusuke; Terazono, Takahiro; Wakao, Shinji; Oozeki, Takashi

PV power output mainly depends on the solar irradiance which is affected by various meteorological factors. So, it is required to predict solar irradiance in the future for the efficient operation of PV systems. In this paper, we develop a novel approach for solar irradiance forecast, in which we introduce to combine the black-box model (JIT Modeling) with the physical model (GPV data). We investigate the predictive accuracy of solar irradiance over wide controlled-area of each electric power company by utilizing the measured data on the 44 observation points throughout Japan offered by JMA and the 64 points around Kanto by NEDO. Finally, we propose the application forecast method of solar irradiance to the point which is difficulty in compiling the database. And we consider the influence of different GPV default time on solar irradiance prediction.

Harmonization of food irradiation in the European Community

International Nuclear Information System (INIS)

Vounakis, H.

1992-01-01

As irradiation is intended to prevent the deterioration of food or for its decontamination, its incorrect application could have health consequences. For this reason and in the absence of appropriate Community rules, the Commission programme on food law (COM (86) 603 final, Commission Communication on Food Law) envisaged a proposal for 1987. At that time six Member States permitted food irradiation to varying extents, two others were completing favourable appraisals while another two had no legislation. The commission proposal on food irradiation requires that only foodstuffs mentioned therein could be irradiated under the prescribed conditions and ensures their free movement while guaranteeing a high degree of protection to the consumer in terms of authorization of installations, control and labelling. The Directive on labelling was also modified to impose specific mention for irradiated foodstuffs. The labelling of irradiated ingredients, the products to be accepted for treatment at Community level, the national authorizations and their transfer to the EEC list, are the main issues actually under discussion in the Council. The European parliament was favourable to a proposal restricting the use of irradiation, to dry herbs and spices. (orig.) [de

Food irradiation: advantages and limitations

International Nuclear Information System (INIS)

Hernandes, N.K.; Vital, H. de C.; Sabaa-Srur, A.U.O.

2003-01-01

Food irradiation is a physical method of processing food (e.g. freezing, canning). It has been thoroughly researched over the last four decades and is recognized as a safe and wholesome method. It has the potential both of disinfesting dried food to reduce storage losses and disinfesting fruits and vegetables to meet quarantine requirements for export trade. Low doses of irradiation inhibit spoilage losses due to sprouting of root and tuber crops. Food- borne diseases due to contamination by pathogenic microorganisms and parasites of meat, poultry, fish, fishery products and spices are on the increase. Irradiation of these solid foods can decontaminate them of pathogenic organisms and thus provide safe food to the consumer. Irradiation can successfully replace the fumigation treatment of cocoa beans and coffee beans and disinfest dried fish, dates, dried fruits, etc. One of the most important advantages of food irradiation processing is that it is a coldprocess which does not significantly alter physico-chemical characters of the treated product. It can be applied to food after its final packaging. Similar to other physical processes of food processing, (e.g. canning, freezing), irradiation is a capital intensive process. Thus, adequate product volume must be made available in order to maximize the use of the facility and minimize the unit cost of treatment. Lack of harmonization of regulations among the countries which have approved irradiated foods hampers the introduction of this technique for international trade. Action at the international level has to be taken in order to remedy this situation. One of the important limitations of food irradiation processing is its slow acceptance by consumers, due inter alia to a perceived association with radioactivity. The food industry tends to be reluctant to use the technology in view of uncertainties regarding consumer acceptance of treated foods. Several market testing and consumer acceptance studies have been carried

Advanced post-irradiation examination techniques for water reactor fuel. Proceedings of a technical committee meeting

International Nuclear Information System (INIS)

2002-03-01

The purpose of the meeting was to provide and overview of the status of post-irradiation examination (PIE) techniques for water cooled reactor fuel assemblies and their components with emphasis given to advanced PIE techniques applied to high burnup fuel. Papers presented at the meeting described progress obtained in non-destructive (e.g. dimensional measurements, oxide layer thickness measurements, gamma scanning and tomography, neutron and X-ray radiography, etc.) and destructive PIE techniques (e.g. microstructural studies, elemental and isotopic analysis, measurement of physical and mechanical properties, etc.) used for investigation of water reactor fuel. Recent practice in high burnup fuel investigation revealed the importance of advanced PIE techniques, such as 3-D tomography, secondary ion mass spectrometry, laser flash, high resolution transmission and scanning electron microscopy, image analysis in microstructural studies, for understanding mechanisms of fuel behaviour under irradiation. Importance and needs for in-pile irradiation of samples and rodlets in instrumented rigs were also discussed. This TECDOC contains 20 individual papers presented at the meeting; each of the papers has been indexed separately

Measurement Of Lead Equivalent Thickness For Irradiation Room: An Analysis

International Nuclear Information System (INIS)

Mohd Khalid Matori; Azuhar Ripin; Husaini Salleh; Mohd Khairusalih Mohd Zin; Muhammad Jamal Muhd Isa; Mohd Faizal Abdul Rahman

2014-01-01

The Malaysian Ministry of Health (MOH) has established that the irradiation room must have a sufficient thickness of shielding to ensure that requirements for the purpose of radiation protection of patients, employees and the public are met. This paper presents a technique using americium-241 source to test and verify the integrity of the shielding thickness in term of lead equivalent for irradiation room at health clinics own by MOH. Results of measurement of 8 irradiation rooms conducted in 2014 were analyzed for this presentation. Technical comparison of the attenuation of gamma rays from Am-241 source through the walls of the irradiation room and pieces of lead were used to assess the lead equivalent thickness of the walls. Results showed that almost all the irradiation rooms tested meet the requirements of the Ministry of Health and is suitable for the installation of the intended diagnostic X-ray apparatus. Some specific positions such as door knobs and locks, electrical plug sockets were identified with potential to not met the required lead equivalent thickness hence may contribute to higher radiation exposure to workers and the public. (author)

Astrobee Periodic Technical Review (PTR) Delta 3

Science.gov (United States)

Provencher, Christopher; Smith, Marion F.; Smith, Ernest Everett; Bualat, Maria Gabriele; Barlow, Jonathan Spencer

2017-01-01

Astrobee is a free flying robot for the inside of the International Space Station (ISS). The Periodic Technical Review (PTR) delta 3 is the final design review of the system presented to stakeholders.

FINAL TECHNICAL REPORT: 20% Wind by 2030: Overcoming the Challenges

Energy Technology Data Exchange (ETDEWEB)

Tom Kaiserski; Dan Lloyd

2012-02-28

The funds allocated through the Wind Powering America (WPA) grant were utilized by the State of Montana to support broad outreach activities communicating the benefits and opportunities of increased wind energy and transmission development. The challenges to increased wind development were also clearly communicated with the understanding that a clearer comprehension of the challenges would be beneficial in overcoming the obstacles to further development. The ultimate purpose of these activities was to foster the increased development of Montana's rich wind resources through increased public acceptance and wider dissemination of technical resources.

Final Technical Report for subcontract number B612144

Energy Technology Data Exchange (ETDEWEB)

Mayali, X. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Marcu, O. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-09-11

The original statement of work stipulated that the Subcontractor shall perform bacterial and algal cultivation and manipulation, microbe isolation, preparation of samples for sequencing and isotopic analysis, data analysis, and manuscript preparation. The Subcontractor shall work closely with Dr. Mayali and other LLNL scientists, and shall participate in monthly SFA meetings (either in person or by telephone). The Subcontractor shall deliver a final report at the conclusion of the work.

Food irradiation nears commercial development

International Nuclear Information System (INIS)

1981-01-01

One person out of eight in the world today suffers from chronic undernourishment. This problem is likely to get worse as the world's population doubles during the next thirty to forty years. Since about 25% or more of our harvested food is lost due to various kinds of wastage and spoilage, food preservation is no less important than food production. To supply the world's demand for food, it is more reasonable to conserve what is produced than to produce more to compensate for subsequent losses. Thus, it is obvious that all methods of preserving food and agricultural produce should be examined to see if their use might alleviate the world's food shortage, and that to develop better and safer techniques of food preservation will improve food supplies. Food preservation is an ever greater problem for the developing countries, not only because of their chronic problems of undernourishment, but also because most of them are in tropical or sub-tropical regions where food spoilage is rapid. The IAEA and the Food and Agriculture Organization (FAO) held a symposium on food irradiation at Colombo in Sri Lanka. The symposium paid special attention to the use of food irradiation in preserving tropical fruits as well as fish and fish products. It also examined the cost of the food irradiation process and compared it with those of conventional processes. Food irradiation is one field in which advance is most likely to be achieved through international co-operation. This co-operation has been supported by the IAEA and FAO in a number of ways. During the last 15 years three previous symposia (Karlsruhe, 1966; Bombay, 1972; Wageningen, 1977), numerous panel meetings, and training courses, have been held on this subject and many nations' food irradiation projects have been supported by technical assistance and co-ordinated research programmes

Integration of the irradiation process to the food industry; Integracion del proceso de irradiacion a la industria alimentaria

Energy Technology Data Exchange (ETDEWEB)

Bustos R, M.E

1991-06-15

Food irradiation process has been studied and researched during 40 years, therefore it has been demonstrated its technical and economical feasibility, the advantages of this technology have been given to know to the consumers through educative campaigns. The marketing tests done in different countries mark the beginning of the trade because the consumers preferred irradiated food due to its quality and the increase of shelf life. This fact marks the incorporation of the irradiation techniques into the food industry. (Author)

ESR detection of irradiated seashells

Energy Technology Data Exchange (ETDEWEB)

Raffi, J. [Laboratoire de Recherche sur la Qualite des Aliments, Faculte de Saint-Jerome, Marseille (France); Hasbany, C. [Laboratoire de Recherche sur la Qualite des Aliments, Faculte de Saint-Jerome, Marseille (France)]|[Laboratoire de Chimie des Produits Naturels, Faculte de Saint-Jerome, Marseille (France); Lesgards, G. [Laboratoire de Chimie des Produits Naturels, Faculte de Saint-Jerome, Marseille (France); Ochin, D. [Institut Agricol et Alimentaire de Lille (France). Lab. de Microbiologie et d`Hygiene Alimentaire

1996-11-01

Among the protocols for identification of irradiated foodstuffs submitted to the European Committee of Standardization, two using ESR (food containing bone or cellulose) were finally accepted as official `draft European standards` in Berlin on 9-10 June 1994. We present here some new results for oyster and mussel shells, and an ESR draft protocol is proposed. (author).

Potential use of nuclear irradiation technology for the microbial industry in Malaysia

International Nuclear Information System (INIS)

Raja, P.; Isyanti, I.

2002-01-01

The potential application of irradiation is numerous. The process seems technically feasible for sterilization of medical devices, pharmaceutical products, foods, cosmetics, packaging materials, scientific laboratory materials like petri dishes, growth media, complying with phytosanitary requirements for fruit and vegetables etc. An awareness of biofertilizer or microbial product has established itself to be a significant part of food production and consumption internationally as well as in Malaysia. People are discovering organic agriculture can serve their need for safe quality food, environment conservation and social accountability. One of the major technical constraints of viable microbial or biofertilizer product production is contaminated free carrier materials. In order to develop the good microbial product, we are practicing the gamma irradiation on our carrier materials and successfully established the product. The different carrier materials were packed and used 25 kGy Cobalt-60 source (JS 8900, SINAGAMA, MINT) for sterilization and simultaneously the materials were sterilized in steam. The cultured Trichoderma virile and T harzianum were mixed with sterilized carrier and observed the colony formin. unit (CFU) on regular intervals. The results showed the efficient colony forming unit on both sterilization method of materials. However, the nuclear irradiation is more cost effective and time saving than steam method. (Author)

Final Scientific/Technical Report for award DE-FC--07-00AL67053

International Nuclear Information System (INIS)

Dixon, Cathy

2005-01-01

The project ''Creating an Educational Consortium to Support the Recruitment and Retention of Expertise for the Nuclear Weapons Complex'' was also known as the Advanced Fuel Cycle Initiative (AFCI) University Fellowship Program. Since its inception, the Advanced Fuel Cycle Initiative program and its predecessor, the Advanced Accelerator Applications (AAA) program, have engaged university researchers and students in the sciences necessary to answer technical questions related to reducing high-level waste volumes, optimizing the economics and performance of Yucca Mountain, reducing the technical need for a second repository, reducing the long-term inventories of plutonium in spent fuel, and enabling the proliferation-resistant recovery of the energy contained in spent fuel. The Advanced Fuel Cycle University Fellowship Program is intended to support top students across the nation in a variety of disciplines that will be required to support transmutation research and technology development in the coming decades

Irradiation influence on the detection of genetic-modified soybeans

International Nuclear Information System (INIS)

Villavicencio, A.L.C.H.; Araujo, M.M.; Baldasso, J.G.; Aquino, S.; Konietzny, U.; Greiner, R.

2004-01-01

Three soybean varieties were analyzed to evaluate the irradiation influence on the detection of genetic modification. Samples were treated in a 60 Co facility at dose levels of 0, 500, 800, and 1000 Gy. The seeds were at first analyzed by Comet Assay as a rapid screening irradiation detection method. Secondly, germination test was performed to detect the viability of irradiated soybeans. Finally, because of its high sensitivity, its specificity and rapidity the polimerase chain reaction was the method applied for genetic modified organism detection. The analysis of DNA by the single technique of microgel electrophoresis of single cells (DNA Comet Assay) showed that DNA damage increased with increasing radiation doses. No negative influence of irradiation on the genetic modification detection was found