Tritium breeding experiments with lithium titanate in thermal-type mockups

International Nuclear Information System (INIS)

Klix, Axel; Takahashi, Akito; Ochiai, Kentaro; Nishitani, Takeo

2004-01-01

Lithium titanate, an advanced tritium breeding material, is currently investigated in integral mock-up experiments at FNS. A method was developed which allows to measure low tritium concentrations directly in this material. The local tritium production rate was obtained by small lithium titanate pellet detectors inserted into the breeding layers which are dissolved after irradiation of the assemblies, and the accumulated tritium was counted by liquid scintillation techniques. The measurement method was applied in mock0-up experiments with candidate materials for the future DEMO reactor breeding blanket. Experimental assemblies consisted of sheets of low activation ferritic steel F82H, lithium titanate, and berylium. Tritium production rate profiles were obtained and compared with results from calculations with the Monte Carlo neutron transport code MCNP-4C. In case of the mock-ups with 95% enriched lithium titanate, the C/E ratios were within the error estimate while larger discrepancies were observed in case of 40% enriched lithium titanate. (author)

A study of tritium behavior in lithium oxide by ion conductivity measurements

International Nuclear Information System (INIS)

Noda, Kenji; Ishii, Yoshinobu; Ohno, Hideo; Watanabe, Hitoshi

1989-01-01

Ion conductivity of lithium oxide (Li 2 O) irradiated with oxygen ions was measured to obtain information about the effects of irradiation on the behavior of lithium ions and tritium. The conductivity around 490 K decreased with the ion fluence, while around 440 K it increased. The decrease around 490 K and the increase around 440 K were assumed to be attributed to the F + centers and the unspecified radiation defects, respectively. From the point of view that the rate determinant in the mechanism of diffusion of lithium ions in Li 2 O leading to the ion conductivity is the same as that of tritium, the diffusivity of tritium is assumed to be as follows: the diffusivity of tritium is decreased by the F + centers in the range from 490 K to the temperature at which almost all of F + centers are recovered, while it is increased around 440 K by the unspecified radiation defects. In addition, effects of the irradiation on valence states of tritium (i.e., T + , T - ) were discussed in terms of the radiation defects. (orig.)

Tritium release from lithium ceramics at constant temperature

International Nuclear Information System (INIS)

Verrall, R.A.; Miller, J.M.

1992-02-01

Analytic methods for post-irradiation annealing tests to measure tritium release from lithium ceramics at constant temperature are examined. Modifications to the Bertone (1) relations for distinguishing diffusion-controlled release from desorption-controlled release are shown. The methods are applied to tests on sintered LiA10 2 ; first-order desorption is shown to control tritium release for these tests

Tritium trapping states induced by lithium-depletion in Li{sub 2}TiO{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Kobayashi, Makoto, E-mail: kobayashi.makoto@LHD.nifs.ac.jp [National Institute for Fusion Science (Japan); Oya, Yasuhisa; Okuno, Kenji [Radioscience Research Laboratory, Faculty of Science, Shizuoka University, Shizuoka (Japan)

2017-04-15

Identifications of tritium trapping states in neutron-irradiated Li{sub 1.8}TiO{sub 2.9} (lithium-depleted Li{sub 2}TiO{sub 3}) were carried out by the out-of-pile tritium release behavior. Tritium release behaviors for neutron-irradiated Li{sub 2}TiO{sub 3} and tritium gas-exposed TiO{sub 2} were also measured for comparison. Among the tritium release spectra for these samples, three tritium release peaks were appeared. By the kinetic analyses of tritium release behaviors, the Arrhenius parameters for three peaks were evaluated. Especially for Li{sub 1.8}TiO{sub 2.9}, there were two tritium release peaks, and the peak in lower temperature region was assigned to the tritium release controlled by the diffusion process in Li{sub 2}TiO{sub 3} structure. The other tritium release peak, which was hardly appeared for Li{sub 2}TiO{sub 3}, was assigned to the release of tritium trapped as hydroxyl groups in Li{sub 1.8}TiO{sub 2.9}, indicating that lithium-depletion would result in the formation of hydroxyl groups in Li{sub 2}TiO{sub 3}. Lithium vacancies existed in Li{sub 2}TiO{sub 3} crystal structure would promote the tritium trapping as hydroxyl groups due to the decreased charge repulsion between lithium ions and tritium ion, resulting in the difficulty of recovering tritium from Li{sub 2}TiO{sub 3} effectively.

Irradiation of lithium aluminate and tritium extraction

International Nuclear Information System (INIS)

Roth, E.; Abassin, J.J.; Botter, F.; Briec, M.; Chenebault, P.; Masson, M.; Rasneur, B.; Roux, N.

1984-12-01

After preselection of the preparation procedures, following short irradiations, γ LiAl0 2 samples submitted to 2.10 19 fast neutrons cm -2 and 1.5 10 20 thermal neutrons cm -2 fluences experienced no apparent damage. Post-irradiation tritium extraction from samples irradiated to 2.10 17 neutrons/cm 2 in quartz ampoules produced mostly tritiated water. When in-pile experiments are performed the sample container material influences greatly the measured ratio of tritium gas to tritiated water - Stainless steel capsules yield more T 2 gas than quartz capsules probably because of a reduction process. Difficulties in interpretation arise from adsoption of tritiated water on the measuring lines. Both experiments showed that much faster extraction rates are obtained from small grain size samples than from large ones at the same open porosity. If diffusion in the grains controls the extraction rates, apparent D values vary from 10 -16 to 1.5 10 -15 cm 2 S -1 in the temperature range explored. Around 500 0 C small grain samples reached equilibrium tritium concentration of a few mCi in 4 hours. Such values are suitable for a blanket concept

Tritium release from lithium silicate and lithium aluminate, in-reactor and out-of-reactor

International Nuclear Information System (INIS)

Johnson, A.B. Jr.

1976-09-01

Studies were conducted to determine the generation and evolution of tritium and helium in lithium aluminate (LiAlO 2 ) and lithium silicate (Li 2 SiO 3 ) by the reaction: Li 6 + n → 4 He + T. Targets were irradiated 4.4 days in the K-West Reactor snout facility. (Silicate GVR* approximately 2.0 cc/cc; aluminate GVR approximately 1.4 cc/cc.) Gas release in-reactor was determined by post-irradiation drilling experiments on aluminum ampoules containing silicate and aluminate targets. In-reactor tritium release (at approximately 100 0 C) was found to decrease linearly with increasing target density. Tritium released in-reactor was primarily in the noncondensible form (HT and T 2 ), while in laboratory extractions (300-1300 0 C), the tritium appeared primarily in the condensible form (HTO and T 2 O). Concentrations of HT (and presumably HTO) were relatively high, indicating moisture pickup in canning operations or by inleakage of moisture after the capsule was welded. Impurities in extracted gases included H 2 O, CO 2 , CO, O 2 , H 2 , NO, SO 2 , SiF 4 and traces of hydrocarbons

Results of neutron irradiation of liquid lithium saturated with deuterium

International Nuclear Information System (INIS)

Tazhibayeva, Irina; Ponkratov, Yuriy; Kulsartov, Timur; Gordienko, Yuriy; Skakov, Mazhyn; Zaurbekova, Zhanna; Lyublinski, Igor; Vertkov, Alexey; Mazzitelli, Giuseppe

2017-01-01

Highlights: • The results on neutron irradiation of liquid lithium saturated with deuterium at the IVG.1M research reactor are described. • At temperatures below 573 K the efficiency coefficient of tritium release is well described by the expression K = 0.015 exp(−14/RT), and above 623 K − K = 10 9 exp(−144/RT). • The T 2 molecules contribution into the overall tritium release becomes apparent at temperatures higher than 673 K and increases with the temperature rise. - Abstract: This paper describes the results on neutron irradiation of liquid lithium saturated with deuterium at the IVG.1 M research reactor. The neutron flux at the reactor core center at 2 MW was 5 10 −13 cm −2 s −1 . The efficiency coefficients of helium and tritium release from lithium saturated with deuterium were calculated. The tritium interaction with lithium atoms (formation and dissociation of lithium tritide) has an effect on tritium release. An increment of sample’s temperature results in tritium release acceleration due to rising of the dissociation rate of lithium tritide. At temperatures below 573 K the efficiency coefficient of tritium release is well described by the expression K = 0.015 exp(−14/RT), and above 623 K − K = 10 9 exp(-144/RT). The T 2 molecules contribution into the overall tritium release becomes apparent at temperatures higher than 673 K and increases with the temperature rise.

Recovery of tritium from lithium-sintered aluminium product (SAP) and lithium-aluminium alloys

International Nuclear Information System (INIS)

Talbot, J.B.; Wiffen, F.W.

1979-01-01

The tritium release rates of irradiated samples of lithium-containing aluminium (Li-Al) and sintered aluminium product (Li-SAP) were investigated to evaluate the potential application of both materials in fusion reactors. The observed release rates followed the pattern expected for bulk diffusion of tritium in a solid. Therefore, diffusion coefficients for tritium in Li-SAP were determined over a temperature range of 383 and 500 0 C and tritium in Li-Al at 450 0 C. At 450 0 C, the diffusion coefficients of tritium in Li-SAP and Li-Al are 2.988 x 10 -10 cm 2 sec -1 and 1.462 x 10 -6 cm 2 sec -1 , respectively. (author)

In-pile test of tritium recovery from lithium oxide

International Nuclear Information System (INIS)

Kurasawa, Toshimasa; Yoshida, Hiroshi; Watanabe, Hitoshi; Takeshita, Hidefumi; Miyauchi, Takejiro; Matsui, Tomoaki

1984-05-01

In-situ tritium recovery experiment with sintered lithium oxide pellets was performed under a high neutron fluence in the JRR-2. The irradiation hole VT-10 is the vertical one in the fuel rods region of the reactor, and the neutron flux is as follows: the thermal neutron flux with the epithermal neutron; 1.12 x 10 14 n/cm 2 . sec, the fast neutron flux; 1.0 x 10 12 n/cm 2 . sec. Irradiation material is the four pellets of cylindrical Li 2 O with the size of 11mm-OD, 1.8mm-ID, 10mm-H, and their total weight is 6.67g(the apparent bulk density 86%TD). A sweep gas capsule with a inner heater was constructed for the present study. Irradiation temperatures were regulated in the high temperature range, 470 -- 760 0 C. Four cycles of irradiation tests were carried out from May to August in 1983, and the effective thermal neutron fluence and the burnup of 6 Li were 5.9 x 10 19 nvt and 0.24% of total lithium(natural abundance of Li), respectively. The amount of generated tritium was calculated to be 31.2Ci by using a value of the depression factor of the thermal neutron flux(0.148) and the effective neutron cross section(543b) for the 6 Li(n, α) 3 H reaction. Present report describes the tritium release behavior in the in-situ tritium recovery apparatus and discuss the effects of the moisture, the hydrogen spiking, the irradiation temperature, etc.. Problems relative to a real time measurement of a comparatively high tritium concentration(10 -1 -- 10 2 μCi/cm 3 ) in the helium gas stream were also investigated. (author)

Results of neutron irradiation of liquid lithium saturated with deuterium

Energy Technology Data Exchange (ETDEWEB)

Tazhibayeva, Irina, E-mail: tazhibayeva@ntsc.kz [Institute of Atomic Energy, National Nuclear Center of RK, Kurchatov (Kazakhstan); Ponkratov, Yuriy; Kulsartov, Timur; Gordienko, Yuriy; Skakov, Mazhyn; Zaurbekova, Zhanna [Institute of Atomic Energy, National Nuclear Center of RK, Kurchatov (Kazakhstan); Lyublinski, Igor [JSC «Red Star», Moscow (Russian Federation); NRNU «MEPhI», Moscow (Russian Federation); Vertkov, Alexey [JSC «Red Star», Moscow (Russian Federation); Mazzitelli, Giuseppe [ENEA, RC Frascati, Frascati (Italy)

2017-04-15

Highlights: • The results on neutron irradiation of liquid lithium saturated with deuterium at the IVG.1M research reactor are described. • At temperatures below 573 K the efficiency coefficient of tritium release is well described by the expression K = 0.015 exp(−14/RT), and above 623 K − K = 10{sup 9} exp(−144/RT). • The T{sub 2} molecules contribution into the overall tritium release becomes apparent at temperatures higher than 673 K and increases with the temperature rise. - Abstract: This paper describes the results on neutron irradiation of liquid lithium saturated with deuterium at the IVG.1 M research reactor. The neutron flux at the reactor core center at 2 MW was 5 10{sup −13} cm{sup −2} s{sup −1}. The efficiency coefficients of helium and tritium release from lithium saturated with deuterium were calculated. The tritium interaction with lithium atoms (formation and dissociation of lithium tritide) has an effect on tritium release. An increment of sample’s temperature results in tritium release acceleration due to rising of the dissociation rate of lithium tritide. At temperatures below 573 K the efficiency coefficient of tritium release is well described by the expression K = 0.015 exp(−14/RT), and above 623 K − K = 10{sup 9} exp(-144/RT). The T{sub 2} molecules contribution into the overall tritium release becomes apparent at temperatures higher than 673 K and increases with the temperature rise.

Tritium release from lithium silicate and lithium aluminate, in-reactor and out-of-reactor

Energy Technology Data Exchange (ETDEWEB)

Johnson, A.B. Jr.

1976-09-01

Studies were conducted to determine the generation and evolution of tritium and helium in lithium aluminate (LiAlO/sub 2/) and lithium silicate (Li/sub 2/SiO/sub 3/) by the reaction: Li/sup 6/ + n ..-->.. /sup 4/He + T. Targets were irradiated 4.4 days in the K-West Reactor snout facility. (Silicate GVR* approximately 2.0 cc/cc; aluminate GVR approximately 1.4 cc/cc.) Gas release in-reactor was determined by post-irradiation drilling experiments on aluminum ampoules containing silicate and aluminate targets. In-reactor tritium release (at approximately 100/sup 0/C) was found to decrease linearly with increasing target density. Tritium released in-reactor was primarily in the noncondensible form (HT and T/sub 2/), while in laboratory extractions (300-1300/sup 0/C), the tritium appeared primarily in the condensible form (HTO and T/sub 2/O). Concentrations of HT (and presumably HTO) were relatively high, indicating moisture pickup in canning operations or by inleakage of moisture after the capsule was welded. Impurities in extracted gases included H/sub 2/O, CO/sub 2/, CO, O/sub 2/, H/sub 2/, NO, SO/sub 2/, SiF/sub 4/ and traces of hydrocarbons.

Tritium sorption in lithium-bismuth and lithium-aluminum alloys

International Nuclear Information System (INIS)

Talbot, J.B.; Smith, F.J.; Land, J.F.; Barton, P.

1976-01-01

The sorption of tritium by molten lithium-bismuth, Li-Bi (15 at.% lithium), and solid equiatomic lithium-aluminum, Li-Al, was investigated to evaluate the potential application of both materials in controlled thermonuclear reactors. The solubility of tritium in molten Li-Bi is less than 0.1 ppb at 500 - 700 0 C and tritium partial pressures of 10 -1 - 10 -3 Torr. Therefore, extraction of tritium from molten Li 2 BeF 4 salt with Li-Bi is not practical. The solubility of hydrogen in solid Li-Al (50 - 50 at.%) at 500 0 C follows Sieverts' Law; the Sieverts' constant was measured to be 1.9 (+-0.1) X 10 4 Torrsup(1/2)/atomic fraction. Tritium sorption in Li-Al ranged from 0.01 to 7 ppm at 400 - 600 0 C at respective tritium partial pressures of 0.14 - 0.52 Torr. (Auth.)

MISTRAL: A comprehensive model for tritium transport in lithium-base ceramics. Pt. 2

International Nuclear Information System (INIS)

Federici, G.; Raffray, A.R.; Abdou, M.A.

1990-01-01

A new tritium transport model called MISTRAL (Model for Investigative Studies of Tritium Release in Lithium Ceramics) has been developed to describe and predict the kinetics of tritium release in lithium ceramic materials for tritium breeding applications in fusion blankets. The model has transient capabilities and has been developed to analyze the full range of transient conditions produced in in-pile tritium recovery experiments and expected in fusion blankets. Calibration of the model against experiments has been done in parallel with its development in order to assess its predictive capabilities and to identify the ranges of potential applicability. The comparisons of the results available for lithium metasilicate and aluminate samples irradiated respectively in the two in-pile tritium recovery experiments LISA1 and MOZART are presented and discussed in this paper. They have been selected for the calibration of the codes as being good examples of various features relevant for tritium release analysis in ceramic breeders under different transient conditions such as change in temperature, purge gas composition and reactor power. (orig.)

Measuring nanocurie quantities of tritium bred in metallic lithium and lithium oxide samples

International Nuclear Information System (INIS)

Bertone, P.C.

1985-01-01

The LBM program requires that nanocurie quantities of tritium, bred in both lithium oxide pellets and lithium samples, be measured with an uncertainty not exceeding + or - 6%. Two methods of accurately measuring nanocurie quantities of tritium bred in LBM lithium oxide pellets and one method of accurately measuring nanocurie quantities of tritium bred in lithium samples are described. Potential errors associated with these tritium measurement techniques are also discussed

Tritium recovery from lithium oxide pellets

International Nuclear Information System (INIS)

Bertone, P.C.; Jassby, D.L.

1984-01-01

The TFTR Lithium Blanket Module is an assembly containing 650 kg of lithium oxide that will be used to test the ability of neutronics codes to model the tritium breeding characteristics of limited-coverage breeding zones in a tokamak. It is required that tritium concentrations as low as 0.1 nCi/g bred in both metallic lithium samples and lithium oxide pellets be measured with an uncertainty not exceeding +- 6%. A tritium assay technique for the metallic samples which meets this criterion has been developed. Two assay techniques for the lithium oxide pellets are being investigated. In one, the pellets are heated in a flowing stream of hydrogen, while in the other, the pellets are dissolved in 12 M hydrochloric acid

In-Pile Assemblies for Investigation of Tritium Release from Li2TiO3 Lithium Ceramic

International Nuclear Information System (INIS)

Shestakov, V.; Tazhibayeva, I.; Kawamura, H.; Kenzhin, Y.; Kulsartov, T.; Chikhray, Y.; Kolbaenkov, A.; Arinkin, F.; Gizatulin, Sh.; Chakrov, P.

2005-01-01

The description of algorithm to design in-pipe experimental ampoule devices (IPAD) is presented here, including description of IPAD design for irradiation tests of highly enriched lithium ceramics at WWR-K reactor. The description of the system for registration of tritium release from ceramics during irradiation is presented as well. Typical curve of tritium release from the IPAD during irradiation under various temperatures of the samples is shown here

Formation of radiation-induced defects and their influence on tritium extraction from lithium silicates in out-of-pile experiments

International Nuclear Information System (INIS)

Abramenkovs, A.A.; Tiliks, J.E.

1991-01-01

Formation and properties of radiation-induced defects and radiolysis products in lithium silicates irradiated in nuclear reactor till absorbed doses 1000 MGy were studied. Radiation-induced defects (RD) and radiolysis products (RP) were qualitatively and quantitatively determinated by methods of chemical scavengers (MHS), electron-spin resonance (ESR) and optical spectroscopy. Colloidal silicon and lithium, lithium and silicon oxides, oxygen, silicon and lithium peroxides are the final products of the lithium silicates radiolysis at absorbed energy doses D abs = 1000 MGy. The concentration of radiation defects and products of radiolysis strongly depend on the temperature of irradiation, humidity, granural size. The thermostimulated extraction of tritiated water (95-98% of the released tritium is in chemical form of water) from lithium silicates ceramics proceeds according to two independent mechanisms: a) chemidesorption of surface localized tritiated water (the first order chemical reaction); b) formation of the tritium water molecules limited by triton diffusion to the near-surface layer of grains. It has been found that the concentration of radiation-induced defects considerably affects the tritium localization and releasing processes from lithium silicates. (orig.)

Investigation of tritium release and retention in lithium aluminate

International Nuclear Information System (INIS)

Kopasz, J.P.; Tistchenko, S.; Botter, F.

1991-01-01

Tritium release from lithium aluminate, although previously investigated by both in-reactor and ex-reactor experiments, remains poorly understood. Agreement between experiments is lacking, and the mechanisms responsible for tritium release from lithium aluminate are under debate. In an effort to improve our understanding of the mechanisms of tritium release from lithium ceramics, we have investigated tritium release from pure lithium aluminate and lithium aluminate doped with impurities. The results of these experiments on large grain size material indicate that after anneals at low temperature, a large fraction of the tritium present before the anneal remains in the sample. We have modeled this behavior based on first-order release from three types of sites. At the lowest temperature, the release is dominated by one site, while the tritium in the other sites is retained in the solid. Adding magnesium dopant to the ceramic appears to alter the distribution of tritium between the sites. This addition decreases the fraction of tritium released at 777 degree C, while increasing the fractions released at 538 and 950 degree C. 11 refs., 8 figs., 1 tab

Extraction of tritium from liquid lithium by permeation

International Nuclear Information System (INIS)

Alire, R.M.

1978-01-01

This paper assesses a method for extracting tritium from liquid lithium for specific application to the conceptual laser fusion reactor that uses a continuous lithium ''waterfall.'' The tritium diffuses through a refractory metal that contains a getter and is then stored in a hydride-forming alloy. There are various uncertainties with this method including helium-4 extraction, unknown impurities that may accumulate in liquid lithium, the effects of these impurities on tritium separation, and the maintenance of tritium-contaminated equipment. Our study indicates that major tritium losses will occur during equipment maintenance rather than as a result of permeation losses through the primary vessel

Study on radiation effect of poly (vinyl alcohol) films irradiated by tritium decay

International Nuclear Information System (INIS)

Li Hairong; Peng Shuming; Zhou Xiaosong; Yu Mingming; Xia Lidong; Chen Xiaohua; Liang Jianhua

2014-01-01

The radiation effect of poly(vinyl alcohol) films used as a kind of gas-barrier material for inertial confinement fusion (ICF) targets was studied under the different conditions of β-ray from tritium decay. The changes of physical and chemical properties of the irradiated material samples were analyzed by FTIR, XRD and AFM. The tritium-hydrogen isotopic exchange reaction of the irradiated samples mainly occurs at C-H bond and the IR absorption peak of C-T bond obviously increases with the irradiation dose. For strong hydrogen bonding interaction, the isotopic exchange reaction doesn't occur at O-H bond. The crystallinity degree and surface morphology of the irradiated samples were changed. The tensile properties of irradiated poly(vinyl alcohol) films were measured by universal material testing machine. The results show that the change trend of mechanical properties is in accordance with the microstructures of the irradiated samples. (authors)

Methods of tritium recovery from molten lithium

International Nuclear Information System (INIS)

Farookhi, R.; Rogers, J.E.

1968-01-01

It is important to keep the tritium inventory in a blanket of a thermonuclear reactor at a low level both to eliminate possible hydriding of structural components and to reduce inventory cost. Removing the tritium from a lithium blanket by fractional distillation, flash vaporization, and fractional crystallization was investigated. No definitive data are available either on the vapor-liquid equilibrium between lithium and tritium at low T 2 concentrations, or on the rate of formation and decomposition of lithium tritide. The final distinction between the recovery systems discussed in this report will depend on such data, but presently distillation appears to be the best alternate to the diffusion scheme proposed by A.P. Fraas. The capital cost of equipment necessary to remove tritium by distillation appears to be greater than 10 million dollars for a 5000 MW system, whereas the capital cost associated with the diffusion process has been estimated to be 4 million dollars

Dependency of irradiation damage density on tritium migration behaviors in Li2TiO3

International Nuclear Information System (INIS)

Kobayashi, Makoto; Toda, Kensuke; Oya, Yasuhisa; Okuno, Kenji

2014-01-01

formation of hydroxyl groups. The efficiency of tritium trapping/detrapping by the dangling oxygen atoms was clearly increased with increasing damage density due to the stabilization of damages by neighboring irradiation damages and/or the lithium burn-up which produces lithium vacancy acting as a pass way of tritium to the dangling oxygen atoms

Determination of effective cross sections and production rates for tritium in the irradiation experiment TRIDEX

International Nuclear Information System (INIS)

Weise, L.

1986-04-01

In the framework of the development of a fusion reactor blanket the irradiation experiment TRIDEX (Tritium Recovery Irradiation DIDO Experiment) takes place at the Juelich Research Reactor FRJ-2 (DIDO). For this equipment the required neutronic calculations have been performed. The aim was the determination of the neutron spectrum and several therefrom derived integral parameters for the irradiation positions in interest. From the calculated effective cross sections for the formation of Tritium resulting from irradiated Lithium samples on one hand and from measured neutron flux densities on the other hand, all needed quantities of the Tritium production could be determined. The calculation of the neutron spectrum has been performed in a two-dimensional x-y-geometry. The neutron flux densities have been gained by gamma-spectrometric measurement of the activities in irradiated activation samples. (orig.) [de

Study of the chemical species of fluorine 18 produced by neutron irradiation of lithium aluminate

International Nuclear Information System (INIS)

Jimenez-Becerril, J.

1990-01-01

In the present work, the chemical form of fluorine-18 obtained by means of the neutron irradiated lithium aluminate was studied, in order to know its chemical behavior and to observe if it volatilizes and adheres to the walls of a tritium distillation system; for this matter paper chromatography and high voltage electrophoresis techniques were used. Lithium aluminate was synthetized, being characterized as LiAlO 2 which was irradiated with neutrons in order to produce fluorine-18. Lithium aluminate is a non-soluble solid, therefore fluorine produced may not be extracted, unless it is dissolved or extracted through the solid. So as not affect in a drastic way the chemical form, it was submitted to extraction processes, agitating the irradiated samples with different acids and basic solutions in order to analyze fluorine-18. The best extraction agent was found to be HCl, where two forms of fluorine-18 were found, one at the point of application, probably as a complex hexafluoride-aluminate and the other as a characteristic Rf of the fluorine ion. In the tritium distillation with helium as a carrier of a sample irradiated and heated up to 220-250 o C, no volatile types of fluorine-18 were found, thus it can be considered that in commercial production of tritium by means of neutron irradiation of lithium aluminate, fluorine-18 is not a damaging pollutant of the equipment pipe system. (Author)

Combined gettering and molten salt process for tritium recovery from lithium

International Nuclear Information System (INIS)

Sze, D.K.; Finn, P.A.; Bartlit, J.; Tanaka, S.; Teria, T.; Yamawaki, M.

1988-02-01

A new tritium recovery concept from lithium has been developed as part of the US/Japan collaboration on Reversed-Field Pinch Reactor Design Studies. This concept combines the γ-gettering process as the front end to recover tritium from the coolant, and a molten salt recovery process to extract tritium for fuel processing. A secondary lithium is used to regenerate the tritium from the gettering bed and, in the process, increases the tritium concentration by a factor of about 20. That way, the required size of the molten salt process becomes very small. A potential problem is the possible poisoning of the gettering bed by the salt dissolved in lithium. 16 refs., 6 figs

The effect of irradiation of the thermal conductivity of lithium ceramics

International Nuclear Information System (INIS)

Ethridge, J.L.; Baker, D.E.

1987-01-01

An apparatus for measuring the thermal conductivity of irradiated lithium ceramics to 900 0 C was designed, fabricated, and tested. Special attention was necessary in order to accommodate tritium released during the high-temperature measurements

Lithium aluminate/zirconium material useful in the production of tritium

Science.gov (United States)

Cawley, W.E.; Trapp, T.J.

A composition is described useful in the production of tritium in a nuclear reactor. Lithium aluminate particles are dispersed in a matrix of zirconium. Tritium produced by the reactor of neutrons with the lithium are absorbed by the zirconium, thereby decreasing gas pressure within capsules carrying the material.

In-situ tritium recovery from Li2O irradiated in fast neutron flux - Beatrix-II temperature change specimen

International Nuclear Information System (INIS)

Slagle, O.D.; Hollenberg, G.W.; Kurasawa, T.; Verrall, R.A.

1992-01-01

The Beatrix-II irradiation experiment is an in-situ tritium release experiment to evaluate the stability and tritium release characteristics of Li 2 O under fast neutron irradiation to extended burnups. A thin annular ring specimen capable of temperature changes was irradiated in Phase I of the experiment to a lithium burnup of 5%. The primary emphasis of the test plan was to determine the effect and interrelationship of gas composition and temperature on the tritium inventory with increasing temperature and a series of specific temperature changes were carried out at intervals throughout the experiment to characterize the effect of burnup. Decreasing the amount of hydrogen in the sweep gas resulted in an increase in the tritium inventory in the Li 2 O specimen. The tritium recovery during startup and shutdown was observed to be strongly influenced by the composition of the sweep gas

Comparison of the tritium residence times of various ceramic breeder materials irradiated in EXOTIC experiments 4 and 5

International Nuclear Information System (INIS)

Kwast, H.; Elen, J.D.; Conrad, R.; Casadio, S.; Werle, H.; Verstappen, G.

1990-09-01

Tritium residence times have been determined for various ceramic tritium breeding materials from in-situ release measurements. The irradiations, codenamed EXOTIC (EXtraction Of Tritium In Ceramics), were carried out in the High Flux Reactor (HFR) Petten. During the irradiation more than 450 transients were performed and the corresponding tritium release measured. Materials supplied by SCK/CEN (Li 2 ZrO 3 ), CEA (Li 2 ZrO 3 and LiAlO 2 ), ENEA (LiAlO 2 ), KfK (Li 4 SiO 4 ), NRL (Li 6 Zr 2 O 7 ) and ECN (Li 8 ZrO 6 ) were irradiated in EXOTIC-5 to compare the tritium residence times obtained under equal conditions. Apart from differences in density, grain size, pore size and OPV it appeared that the tritium residence times of the lithium zirconates (pellets) were shorter than those of the Li 4 SiO 4 pebbles. The tritium residence times of the Li 4 SiO 4 pebbles were shorter than those of the LiAlO 2 pellets. (author). 7 refs.; 5 figs.; 3 tabs

Phase transformations in lithium aluminates irradiated with neutrons

International Nuclear Information System (INIS)

Carrera, L.M.; Delfin L, A.; Urena N, F.; Basurto, R.; Bosch, P.

2003-01-01

The lithium aluminate like candidate to be used in the coverings producers of tritium in the fusion nuclear reactors, presents high resistance to the corrosion to the one to be stuck to structural materials as special steels. However, the crystallographic changes that take place in the cover that is continually subjected to irradiation with neutrons, can alter its resistance to the corrosion. In this work the changes of crystalline structure are shown that they present two types of nano structures of lithium aluminates, subjected to an average total dose 7.81 x 10 8 Gy in the fixed irradiation system of capsules of the one TRIGA Mark lll nuclear reactor of the Nuclear Center of Mexico. The studied nano structures presented only phase transformations without formation of amorphous material. (Author)

Lithium ceramics: sol-gel preparation and tritium release

International Nuclear Information System (INIS)

Renoult, O.

1994-04-01

Ceramics based on lithium aluminate (LiA1O 2 ), lithium zirconate (Li 2 ZrO 3 ) and lithium titanate (Li 2 TiO 3 ) are candidates as tritium breeder blanket materials for forthcoming nuclear fusion reactors. Lithium silico-aluminate Li 4+x A1 4-3x Si 2x O 8 (0 ≤ x ≤ 0,25) powders were synthetized from alkoxyde-hydroxyde sol-gel route. By direct sintering at 850-1100 deg C (without prior calcination), ceramics with controlled stoichiometry and homogenous microstructure were obtained. We have also prepared, using a comparable method, Li 2 Zr 1-x Ti x O 3 (x = 0, x = 0,1 et x = 1) materials. All these ceramics, with different microstructures and compositions, have been tested in out-of-reactor experiments. Concerning lithium aluminate microporous ceramics, the silicon substitution leads to a significant improvement of the tritrium release. Classical models taking into account independent surface mechanisms are not able to describe correctly the observed tritium release kinetics. We show, using a simple model, that the release kinetics is in fact limited by an intergranular diffusion followed by a desorption. The delay in tritium release, which occurs when the ceramic compacity increases, is explained in terms of an enhancement of the ionic T + diffusion path length. The energy required for desorption includes a leading term independent of hydrogen contained in the sweep gas. This term is attributed to the limiting recombination step of T + in molecular species HTO. For similar microstructures, the facility of tritium release for the different studied materials is explained by three properties: the crystal structure of the ceramic, the acidity of oxides and finally the presence of electronic non-stoichiometric defects. (author). 89 refs., 50 figs., 2 tabs., 1 annexe

Preparation of 18F in a research reactor, from irradiated lithium carbonate

International Nuclear Information System (INIS)

Gariglia, H.T.; Silva, C.P.G. da.

1978-01-01

A procedure for preparation of carrier - free fluorine-18 is described. The 18 F is produced by neutron irradiation of lithium carbonate and is separated by passing the dissolved material through a 1000 0 C calcinated aluminium oxyde column. The yield is about 90%, the tritium content 2%; other radioactive impurities are not found. The radiochemical purity is about 93% and the lithium content of the solution is [pt

Distillation plant for tritium enrichment in metallic lithium

International Nuclear Information System (INIS)

Barnert, E.; Butzek, D.; Cordewiner, J.; Heinrichs, E.

1984-06-01

To close the external fuel cycle of fusion reactors, the tritium obtained from lithium must be separated off. One way of doing this is by high-temperature distillation and subsequent permeation. The construction of high-temperature distillation plant is described. For the time being, deuterium is processed instead of tritium. (orig.) [de

Lithium test module on ITER: engineering design of the tritium recovery system

International Nuclear Information System (INIS)

Finn, P.A.

1988-01-01

The design presented is an overview of the tritium recovery system for a lithium module on an ITER type reactor. The design of a tritium recovery system for larger blanket units, sectors, etc. could use the information developed in this report. A goal of this design was to ensure that a reliable, integrated performance of the tritium recovery system could be demonstrated. An equally important goal was to measure and account for the tritium in the liquid lithium blanket module and its recovery system in order to validate the operation of the blanket module

Fabrication of lithium ceramic pellets, rings and single crystals for irradiation in BEATRIX-II

International Nuclear Information System (INIS)

Slagle, O.D.; Noda, K.; Takahashi, T.

1989-04-01

BEATRIX-II is an IEA sponsored experiment of lithium ceramic solid breeder materials in the FFTF/MOTA. Li 2 O solid pellets and annular ring specimens were fabricated for in-situ tritium release tests. In addition, a series of single crystal and polycrystalline lithium ceramic samples were fabricated to determine the irradiation behavior and beryllium compatibility. 6 refs., 10 figs., 4 tabs

Retention and release of tritium in aluminum clad, Al-Li alloys

International Nuclear Information System (INIS)

Louthan, M.R. Jr.

1991-01-01

Tritium retention in and release from aluminum clad, aluminum-lithium alloys is modeled from experimental and operational data developed during the thirty plus years of tritium production at the Savannah River Site. The model assumes that tritium atoms, formed by the 6 Li(n,α) 3 He reaction, are produced in solid solution in the Al-Li alloy. Because of the low solubility of hydrogen isotopes in aluminum alloys, the irradiated Al-Li rapidly becomes supersaturated in tritium. Newly produced tritium atoms are trapped by lithium atoms to form a lithium tritide. The effective tritium pressure required for trap or tritide stability is the equilibrium decomposition pressure of tritium over a lithium tritide-aluminum mixture. The temperature dependence of tritium release is determined by the permeability of the cladding to tritium and the local equilibrium at the trap sites. This model is used to calculate tritium release from aluminum clad, aluminum-lithium alloys. 9 refs., 3 figs

Release characteristics of tritium from high-purity lithium oxide

International Nuclear Information System (INIS)

O'Kula, K.R.; Vogelsang, W.F.

1985-01-01

Rates of tritium release from neutronirradiated lithium oxide were determined from isothermal release experiments. High-purity, monocrystalline lithium oxide was purged ex-reactor with helium and helium-hydrogen gas streams. Overall release was found to be controlled by solid-phase diffusion, and was predominantly in the form of condensible species. The result of an independent concentration profile analysis at 923 K was in agreement with the gas release diffusion coefficient. Sweeping the Li 2 O with hydrogen-containing gas was found to enhance tritium removal during the early stage of each run

Study on tritium recovery from breeder materials

International Nuclear Information System (INIS)

Moriyama, H.; Moritani, K.

1997-01-01

For the development of fusion reactor blanket systems, some of the key issues on the tritium recovery performance of solid and liquid breeder materials were studied. In the case of solid breeder materials, a special attention was focussed on the effects of irradiation on the tritium recovery performance, and tritium release experiments, luminescence measurements of irradiation defects and modeling studies were systematically performed. For liquid breeder materials, tritium recovery experiments from molten salt and liquid lithium were performed, and the technical feasibility of tritium recovery methods was discussed. (author)

Handling of tritium-bearing wastes

International Nuclear Information System (INIS)

1981-01-01

The generation of nuclear power and reprocessing of nuclear fuel results in the production of tritium and the possible need to control the release of tritium-contaminated effluents. In assessing the need for controls, it is necessary to know the production rates of tritium at different nuclear facilities, the technologies available for separating tritium from different gaseous and liquid streams, and the methods that are satisfactory for storage and disposal of tritiated wastes. The intention in applying such control technologies and methods is to avoid undesirable effects on the environment, and to reduce the radiation burden on operational personnel and the general population. This technical report is a result of the IAEA Technical Committee Meeting on Handling of Tritium-bearing Effluents and Wastes, which was held in Vienna, 4 - 8 December 1978. It summarizes the main topics discussed at the meeting and appends the more detailed reports on particular aspects that were prepared for the meeting by individual participants

Tritium transport modeling at system level for the EUROfusion dual coolant lithium-lead breeding blanket

Science.gov (United States)

Urgorri, F. R.; Moreno, C.; Carella, E.; Rapisarda, D.; Fernández-Berceruelo, I.; Palermo, I.; Ibarra, A.

2017-11-01

The dual coolant lithium lead (DCLL) breeding blanket is one of the four breeder blanket concepts under consideration within the framework of EUROfusion consortium activities. The aim of this work is to develop a model that can dynamically track tritium concentrations and fluxes along each part of the DCLL blanket and the ancillary systems associated to it at any time. Because of tritium nature, the phenomena of diffusion, dissociation, recombination and solubilisation have been modeled in order to describe the interaction between the lead-lithium channels, the structural material, the flow channel inserts and the helium channels that are present in the breeding blanket. Results have been obtained for a pulsed generation scenario for DEMO. The tritium inventory in different parts of the blanket, the permeation rates from the breeder to the secondary coolant and the amount of tritium extracted from the lead-lithium loop have been computed. Results present an oscillating behavior around mean values. The obtained average permeation rate from the liquid metal to the helium is 1.66 mg h-1 while the mean tritium inventory in the whole system is 417 mg. Besides the reference case results, parametric studies of the lead-lithium mass flow rate, the tritium extraction efficiency and the tritium solubility in lead-lithium have been performed showing the reaction of the system to the variation of these parameters.

Tritium transport in lithium ceramics porous media

International Nuclear Information System (INIS)

Tam, S.W.; Ambrose, V.

1991-01-01

A random network model has been utilized to analyze the problem of tritium percolation through porous Li ceramic breeders. Local transport in each pore channel is described by a set of convection-diffusion-reaction equations. Long range transport is described by a matrix technique. The heterogeneous structure of the porous medium is accounted for via Monte Carlo methods. The model was then applied to an analysis of the relative contribution of diffusion and convective flow to tritium transport in porous lithium ceramics. 15 refs., 4 figs

Study of tritium removal from fusion reactor blankets of molten salt and lithium--aluminum

International Nuclear Information System (INIS)

Talbot, J.B.

1976-03-01

The sorption of tritium by molten lithium--bismuth (Li--Bi, approx. 15 at. % lithium) and solid equiatomic lithium--aluminum (Li--Al) was investigated experimentally to evaluate the potential applications of both materials in a controlled thermonuclear reactor. The Li--Bi alloy was proposed to countercurrently extract tritium from a molten salt (Li 2 BeF 4 ) blanket. However, because of the low solubility ( 0 C, the extraction process is not attractive

Lithium ceramics: sol-gel preparation and tritium release; Ceramiques lithiees: elaboration sol-gel et relachement du tritium

Energy Technology Data Exchange (ETDEWEB)

Renoult, O

1994-04-01

Ceramics based on lithium aluminate (LiA1O{sub 2}), lithium zirconate (Li{sub 2}ZrO{sub 3}) and lithium titanate (Li{sub 2}TiO{sub 3}) are candidates as tritium breeder blanket materials for forthcoming nuclear fusion reactors. Lithium silico-aluminate Li{sub 4+x}A1{sub 4-3x}Si{sub 2x}O{sub 8} (0 {<=} x {<=} 0,25) powders were synthetized from alkoxyde-hydroxyde sol-gel route. By direct sintering at 850-1100 deg C (without prior calcination), ceramics with controlled stoichiometry and homogenous microstructure were obtained. We have also prepared, using a comparable method, Li{sub 2}Zr{sub 1-x}Ti{sub x}O{sub 3} (x = 0, x = 0,1 et x = 1) materials. All these ceramics, with different microstructures and compositions, have been tested in out-of-reactor experiments. Concerning lithium aluminate microporous ceramics, the silicon substitution leads to a significant improvement of the tritrium release. Classical models taking into account independent surface mechanisms are not able to describe correctly the observed tritium release kinetics. We show, using a simple model, that the release kinetics is in fact limited by an intergranular diffusion followed by a desorption. The delay in tritium release, which occurs when the ceramic compacity increases, is explained in terms of an enhancement of the ionic T{sup +} diffusion path length. The energy required for desorption includes a leading term independent of hydrogen contained in the sweep gas. This term is attributed to the limiting recombination step of T{sup +} in molecular species HTO. For similar microstructures, the facility of tritium release for the different studied materials is explained by three properties: the crystal structure of the ceramic, the acidity of oxides and finally the presence of electronic non-stoichiometric defects. (author). 89 refs., 50 figs., 2 tabs., 1 annexe.

Direct tritium measurement in lithium titanate for breeding blanket mock-up experiments with D-T neutrons

International Nuclear Information System (INIS)

Klix, A.; Ochiai, K.; Nishitani, T.; Takahashi, A.

2004-01-01

At Fusion Neutronics Source (FNS) of JAERI, tritium breeding experiments with blanket mock-ups consisting of advanced fusion reactor materials are in progress. The breeding zones are thin layers of lithium titanate which is one of the candidate tritium breeder materials for the DEMO fusion power reactor. It is anticipated that the application of small pellet-shaped lithium titanate detectors manufactured from the same material as the breeding layer will reduce experimental uncertainties arising from necessary corrections due to different isotopic lithium volume concentrations in breeding material and detector. Therefore, a method was developed to measure the local tritium production by means of lithium titanate pellet detectors and a liquid scintillation counting technique. The lithium titanate pellets were dissolved in concentrated hydrochloric acid solution and the resulting acidic solution was neutralized. Two ways of further processing were followed: direct incorporation into a liquid scintillation cocktail and distillation of the solution followed by mixing with liquid scintillator. Two types of lithium titanate pellets were investigated with different 6 Li enrichment and manufacturing procedure. It was found that lithium titanate is suitable for tritium production measurements. However some discrepancies in the measurement accuracy remained with one of the investigated pellet detectors when compared with a well-established lithium carbonate measurement technique and this issue needs further investigation

Study of tritium removal from fusion reactor blankets of molten salt and lithium--aluminum

International Nuclear Information System (INIS)

Talbot, J.B.

1976-03-01

The sorption of tritium by molten lithium--bismuth (Li--Bi, approximately 15 at. percent lithium) and solid equiatomic lithium--aluminum (Li--Al) was investigated experimentally to evaluate the potential applications of both materials in a controlled thermonuclear reactor. The Li--Bi alloy was proposed to countercurrently extract tritium from a molten salt (Li 2 BeF 4 ) blanket. However, because of the low solubility (less than 10 ppb) at temperatures ranging from 500 to 700 0 C, the extraction process is not attractive

Tritium release from neutron irradiated beryllium pebbles

Energy Technology Data Exchange (ETDEWEB)

Scaffidi-Argentina, F.; Werle, H. [Forschungszentrum Karlsruhe GmbH Technik und Umwelt (Germany). Inst. fuer Neutronenphysik und Reactortechnik

1998-01-01

One of the most important open issues related to beryllium for fusion applications refers to the kinetics of the tritium release as a function of neutron fluence and temperature. The EXOTIC-7 as well as the `Beryllium` experiments carried out in the HFR reactor in Petten are considered as the most detailed and significant tests for investigating the beryllium response under neutron irradiation. This paper reviews the present status of beryllium post-irradiation examinations performed at the Forschungszentrum Karlsruhe with samples from the above mentioned irradiation experiments, trying to elucidate the tritium release controlling processes. In agreement with previous studies it has been found that release starts at about 500-550degC and achieves a maximum at about 700-750degC. The observed release at about 500-550degC is probably due to tritium escaping from chemical traps, while the maximum release at about 700-750degC is due to tritium escaping from physical traps. The consequences of a direct contact between beryllium and ceramics during irradiation, causing tritium implanting in a surface layer of beryllium up to a depth of about 40 mm and leading to an additional inventory which is usually several times larger than the neutron-produced one, are also presented and the effects on the tritium release are discussed. (author)

An assembly of tritium production experiment

International Nuclear Information System (INIS)

Abe, Toshihiko

1981-01-01

An assembly for tritium production experiment, i.e. Tritium Extraction System (TREX) constructed as a small scale test facility for tritium production, and Tritium Removal System (TRS) attached to TREX, and the preliminary results of the experiments with them are described. The radiological safety of the process and operation is also an important consideration. Lithium-aluminum alloy was selected as the most promising target material. The following matters are involved in the scope of production technology: the selection of a target material and target preparation, reactor irradiation, the construction of a facility for the extraction of tritium from the irradiated target, the establishment of the optimum conditions of extraction, the purification, collection and storage of tritium, and the inspection of the product. The tritium production experiment at JAERI is yet on the initial stage; the development is to be continued with the stepwise increase of the scale of tritium production. (J.P.N.)

The effect of helium generation and irradiation temperature on tritium release from neutron irradiated beryllium

International Nuclear Information System (INIS)

Kupriyanov, I.B.; Gorokhov, V.A.; Vlasov, V.V.; Kovalev, A.M.; Chakin, V.P.

2004-01-01

The effect of neutron irradiation condition on tritium release from beryllium is described in this paper. Beryllium samples were irradiated in the SM reactor with neutron fluence (E > 0.1 MeV) of (0.37-2.0) x 10 22 cm -2 at 70-100degC and 650-700degC. Mass-spectrometer technique was used in out of tritium release experiments during stepped-temperature anneal within a temperature range from 250 to 1300degC. The total amount of helium accumulated in irradiated beryllium samples varied from 521 appm to 3061 appm. The first signs of tritium release were detected at temperature of 406-553degC. It was shown that irradiation temperature and helium generation level significantly affect the tritium release. A fraction of 44 - 74 % of tritium content in samples irradiated at low temperature (70 - 100degC) is release from beryllium at an annealing temperature below 800degC, whereas for samples after high temperature irradiation (650 - 700 degC) tritium release did not exceed 14 %. Majority of tritium (∼68%) is released within a temperature range from 800 to 920 degC. The increase of helium generation from 521 appm to 3061 appm results in lowering the temperature of maximal tritium release rate and the upper temperature of tritium release from beryllium by 100-130degC and 200-240degC, correspondingly. On the basis of data obtained, the diffusion coefficients of tritium in beryllium were calculated. (author)

Design data, liquid distributors and condenser for a distillation column to enrich tritium in metallic lithium

International Nuclear Information System (INIS)

Barnert, E.

1984-01-01

Tritium, one fuel component of the fusion reactor is bred from the reactors blanket material lithium. Before extracting the tritium from, for instance, metallic lithium by permeation it has to be enriched in the lithium by high temperature distillation. In this report design data for a column for high temperature distillation are given. About the testing of two distributors for small liquid quantities and of a condenser is reported. (orig.) [de

The FUBR-1B experiment, irradiation of lithium ceramics to high burnups under large temperature gradients

International Nuclear Information System (INIS)

Hollenberg, G.W.; Knight, R.C.; Densley, P.J.; Pember, L.A.; Johnson, C.E.; Poeppel, R.B.; Yang, L.

1985-01-01

Solid breeder materials used for supplying the tritium for fueling fusion power reactors will be required to withstand a variety of severe environmental conditions such as irradiation damage, thermal stresses and chemical reactions while continuing to produce tritium and not interfering with other essential components in the complex blanket region. In the FUBR-1B experiment several solid breeder candidates are being subjected to the most hostile conditions foreseen in a fusion reactor's blanket. Some material, such as Li 2 O, Li 8 ZrO 6 , and Li 4 SiO 4 , possess high lithium atom densities which are reflected in high tritium breeding ratios. Other material, such as LiAlO 2 and Li 2 ZrO 3 , appear to have exceptional irradiation stability. Verifying the magnitude of these differences will allow national selection between design options

Equilibrium and kinetic studies of systems of hydrogen isotopes, lithium hydrides, aluminum, and LiAlO2

International Nuclear Information System (INIS)

Owen, J.H.; Randall, D.

1976-01-01

Tritium might be bred by the 6 Li(n,α)T reaction in a solid lithium alloy or compound in the blanket of a controlled thermonuclear reactor to avoid problems associated with molten lithium or lithium compounds. Li--Al and LiAlO 2 systems containing hydrogen, deuterium, or tritium were studied 10 to 15 years ago at the Savannah River Laboratory. This paper descibes measurements of (1) the distribution of tritium and helium throughout both α and β phases of irradiated Li--Al alloy, (2) the migration rate of tritium to the β phase during moderate heating, (3) equilibrium pressures as functions of temperature of H 2 , D 2 , or T 2 in contact with lithium hydrides + aluminum, Li--Al alloy, or irradiated Li--Al alloy, (4) the equilibrium constant for the reaction LiH + Al → LiAl + 1 / 2 H 2 as a function of temperature, and (5) extraction rates of tritium from irradiated LiAlO 2 targets at elevated temperatures

EXOTIC: Development of ceramic tritium breeding materials

International Nuclear Information System (INIS)

Flipot, A.J.; Kennedy, P.; Conrad, R.

1989-03-01

As part of the joint European Programme on fusion blanket technology three laboratories, Northern Research Laboratories (NRL), Springfields in the UK, SCK/CEN-Mol in Belgium and ECN-Petten in conjunction with JRC-Petten in the Netherlands have worked closely together since 1983 on the development of ceramic breeder materials, the programme being codenamed EXOTIC. Lithium oxides, aluminates, silicates and zirconates have been produced, characterised and irradiated in the HFR-Petten in experiments EXOTIC-1, -2 and -3. EXOTIC-4 is in preparation. In this fourth annual progress report the work achieved in 1987 is reported. For EXOTIC-1 to -3 mainly post irradiation examinations have been carried out like: visual inspection, puncturing of closed capsules, tritium retention measurements and material characterisation. Moreover, tritium release experiments on small specimens have started. SCK/CEN performed a general study on lithium silicates, in particular on the thermal stability. Finally, the fabrication and the characterisation of the materials to be irradiated in experiment EXOTIC-4 are presented. The eight capsules of EXOTIC-4 will be loaed with samples of Li 2 SiO 3 , Li 2 O, Li 2 ZrO 3 , Li 6 Zr 2 O 7 and Li 8 ZrO 6 . The irradiation will last 4 reactor cycles or about 100, Full Power Day, FPD. The main objective is to determine the tritium residence time of the various lithium zirconates. 18 figs., 8 refs., 15 tabs

Study of damages by neutron irradiation in lithium aluminates

International Nuclear Information System (INIS)

Palacios G, O.

1999-01-01

Lithium aluminates proposed to the production of tritium in fusion nuclear reactors, due to the thermal stability that they present as well as the behavior of the aluminium to the irradiation. As a neutron flux with profile (≅ 14 Mev) of a fusion reactor is not available. A irradiation experiment was designed in order to know the micro and nano structure damages produced by fast and thermal neutrons in two irradiation positions of the fusion nuclear reactor Triga Mark III: CT (Thermal Column) and SIFCA (System of Irradiation Fixed of Capsules). In this work samples of lithium aluminate were characterized by XRD (X-Ray Diffraction), TEM (Transmission Electron Microscopy) and SEM (Scanning Electron Microscopy). Two samples were prepared by two methods: a) coalition method and b) peroxide method. This characterization comprised original and irradiated samples. The irradiated sample amounted to 4 in total: one for each preparation method and one for each irradiation position. The object of this analysis was to correlate with the received neutron dose the damages suffered by the samples with the neutron irradiation during long periods (440 H), in their micro and nano structure aspects; in order to understand the changes as a function of the irradiation zone (with thermal and fast neutron flux) and the preparation methods of the samples and having as an antecedent the irradiation in SIFCA position by short times (2h). The obtained results are referred to the stability of γ -aluminate phase, under given conditions of irradiation and defined nano structure arrangement. They also refer to the proposals of growth mechanism and nucleation of new phases. The error associated with the measurement of neutron dose is also discussed. (Author)

In-pile test of tritium release from tritium breeding materials (VOM-21H experiment)

International Nuclear Information System (INIS)

Kurasawa, Toshimasa; Takeshita, Hidefumi; Watanabe, Hitoshi; Yoshida, Hiroshi.

1986-10-01

Material development and blanket design of lithium-based ceramics such as lithium oxide, lithium aluminate, lithium silicate and lithium zirconate have been performed in Japan, United State of America and Europian Communities. Lithium oxide is a most attractive candidate for tritium breeding materials because of its high lithium density, high thermal conductivity and good tritium release performance. This work has been done to clarify the characteristics of tritium release and recovery from Li 2 O by means of in-situ tritium release measurement. The effects of temperature and sweep gas composition on the tritium release were investigated in this VOM-21H Experiment. Good measurement of tritium release was achieved but there were uncertainties in reproduciblity of data. The experimental results show that the role of surface adsorption/desorption makes a significant contribution to the tritium release and tritium inventory. Also, it is necessary to define the rate limiting process either diffusion or surface adsorption/desorption. (author)

Tritium and helium release from beryllium pebbles neutron-irradiated up to 230appm tritium and 3000appm helium

Directory of Open Access Journals (Sweden)

Vladimir Chakin

2016-12-01

Full Text Available Study of tritium and helium release from beryllium pebbles with diameters of 0.5 and 1mm after high-dose neutron irradiation at temperatures of 686–968K was performed. The release rate always has a single peak, and the peak temperatures at heating rates of 0.017K/s and 0.117K/s lie in the range of 1100–1350K for both tritium and helium release. The total tritium release from 1mm pebbles decreases considerably by increasing the irradiation temperature. The total tritium release from 0.5mm pebbles is less than that from 1mm pebbles and remains constant regardless of the irradiation temperature. At high irradiation temperatures, open channels are formed which contribute to the enhanced tritium release.

Tritium target performance during an LBLOCA in a PWR

International Nuclear Information System (INIS)

Reid, B.D.

1996-01-01

In December 1995, the U.S. Department of Energy (DOE) announced a preferred strategy for acquiring a new supply of tritium. That strategy is based on pursuing the two most promising production alternatives. These alternatives include either constructing an accelerator-produced tritium system for tritium production or procuring an existing commercial light water reactor or irradiation services from such a reactor to irradiate tritium targets. This paper discusses the safety performance of a tritium target in a commercial pressurized water reactor (PWR). The current conceptual design for the light water tritium targets is quite similar, in terms of external dimensions and materials, to early designs for stainless steel clad discrete burnable absorbers used in PWRs. The tritium targets nominally consist of an annular lithium aluminate pellet wrapped in a Zircaloy-4 getter and clad with Type 316 stainless steel

Electronic properties of lithium titanate ceramic

International Nuclear Information System (INIS)

Padilla-Campos, Luis; Buljan, Antonio

2001-01-01

Research on tritium breeder material is fundamental to the development of deuterium-tritium type fusion reactors for producing clean, non contaminating, electrical energy, since only energy and helium, a harmless gas, are produced from the fusion reaction. Lithium titanate ceramic is one of the possible candidates for the tritium breeder material. This last material is thought to form part of the first wall of the nucleus of the reactor which will provide the necessary tritium for the fusion and will also serve as a shield. Lithium titanate has advantageous characteristics compared to other materials. Some of these are low activation under the irradiation of neutrons, good thermal stability, high density of lithium atoms and relatively fast tritium release at low temperatures. However, there are still several physical and chemical properties with respect to the tritium release mechanism and mechanical properties that have not been studied at all. This work presents a theoretical study of the electronic properties of lithium titanate ceramic and the corresponding tritiated material. Band calculations using the Extended H kel Tight-Binding approach were carried out. Results show that after substituting lithium for tritium atoms, the electronic states for the latter appear in the middle of prohibited band gap which it is an indication that the tritiated material should behave as a semiconductor, contrary to Li 2 TiO 3 which is a dielectric isolator. A study was also carried out to determine the energetically most favorable sites for the substitution of lithium for tritium atoms. Additionally, we analyzed possible pathways for the diffusion of a tritium atom within the crystalline structure of the Li 2 TiO 3

Influence of neutron irradiation on the tritium retention in beryllium

Energy Technology Data Exchange (ETDEWEB)

Rolli, R.; Ruebel, S.; Werle, H. [Forschungszentrum Karlsruhe, Inst. fuer Neutronenphysik und Reaktortechnik, Karlsruhe (Germany); Wu, C.H.

1998-01-01

Carbon-based materials and beryllium are the candidates for protective layers on the components of fusion reactors facing plasma. In contact with D-T plasma, these materials absorb tritium, and it is anticipated that tritium retention increases with the neutron damage due to neutron-induced traps. Because of the poor data base for beryllium, the work was concentrated on it. Tritium was loaded into the samples from stagnant T{sub 2}/H{sub 2} atmosphere, and afterwards, the quantity of the loaded tritium was determined by purged thermal annealing. The specification of the samples is shown. The samples were analyzed by SEM before and after irradiation. The loading and the annealing equipments are contained in two different glove boxes with N{sub 2} inert atmosphere. The methods of loading and annealing are explained. The separation of neutron-produced and loaded tritium and the determination of loaded tritium in irradiated samples are reported. Also the determination of loaded tritium in unirradiated samples is reported. It is evident that irradiated samples contained much more loaded tritium than unirradiated samples. The main results of this investigation are summarized in the table. (K.I.)

Multi-layered, chemically bonded lithium-ion and lithium/air batteries

Science.gov (United States)

Narula, Chaitanya Kumar; Nanda, Jagjit; Bischoff, Brian L; Bhave, Ramesh R

2014-05-13

Disclosed are multilayer, porous, thin-layered lithium-ion batteries that include an inorganic separator as a thin layer that is chemically bonded to surfaces of positive and negative electrode layers. Thus, in such disclosed lithium-ion batteries, the electrodes and separator are made to form non-discrete (i.e., integral) thin layers. Also disclosed are methods of fabricating integrally connected, thin, multilayer lithium batteries including lithium-ion and lithium/air batteries.

Desorption of tritium and helium from high dose neutron irradiated beryllium

Science.gov (United States)

Kupriyanov, I. B.; Nikolaev, G. N.; Vlasov, V. V.; Kovalev, A. M.; Chakin, V. P.

2007-08-01

The effect of high dose neutron irradiation on tritium and helium desorption in beryllium is described. Beryllium samples were irradiated in the SM and BOR-60 reactors to a neutron fluences ( E > 0.1 MeV) of (5-16) × 10 22 cm -2 at 70-100 °C and 380-420 °C. A mass-spectrometry technique was used in out of pile tritium release experiments during stepped annealing in the 250-1300 °C temperature range. The total amount of helium accumulated in irradiated beryllium samples varied from 6000 to 7200 appm. The first signs of tritium and helium release were detected at temperature of 312-445 °C and 500-740 °C, respectively. It is shown that most tritium (˜82%) from sample irradiated at 70-100 °C releases in temperature range of 312-700 °C before the beginning of helium release (740 °C). In the case of beryllium sample irradiated at 380-420 °C, tritium release starts at a higher temperature ( Ts > Tann = 445 °C) and most of the tritium (˜99.8%) is released concurrently with helium which could be considered as evidence of co-existence of partial amounts of tritium and helium in common bubbles. Both the Be samples differ little in the upper temperatures of gas release: 745 and 775 °C for tritium; 1140 and 1160 °C for helium. Swelling of beryllium starts to play a key role in accelerating tritium release at Tann > 600 °C and in helium release - at Tann > 750 °C.

CRITIC-I: Instrumented lithium oxide irradiation: Part 1, Lithium oxide fabrication and characteristics

International Nuclear Information System (INIS)

Applegate, D.S.; Poeppel, R.B.

1987-06-01

Fine-grained, sinterable lithium oxide powder was prepared by high-temperature vacuum calcination of molten lithium carbonate. The product was ball milled, cold pressed, and fired in an oxygen atmosphere. The fired density, grain size, and surface roughness varied widely with firing schedule. Most variations were attributed to moisture content. Rings of high-density, sintered lithium oxide will be used in an in-reactor experiment to measure tritium release. 2 refs., 8 figs., 1 tab

Calibrations of a tritium extraction facility

International Nuclear Information System (INIS)

Bretscher, M.M.; Oliver, B.M.; Farrar, H. IV.

1983-01-01

A tritium extraction facility has been built for the purpose of measuring the absolute tritium concentration in neutron-irradiated lithium metal samples. Two independent calibration procedures have been used to determine what fraction, if any, of tritium is lost during the extraction process. The first procedure compares independently measured 4 He and 3 H concentrations from the 6 Li(n,α)T reaction. The second procedure compared measured 6 Li(n,α)T/ 197 Au (n,γ) 198 Au thermal neutron reaction rate ratios with those obtained from Monte Carlo calculations using well-known cross sections. Both calibration methods show that within experimental errors (approx. 1.5%) no tritium is lost during the extraction process

Research of CITP-II tritium production irradiation device design

International Nuclear Information System (INIS)

Zhang Zhihua; Deng Yongjun; Mi Xiangmiao; Li Rundong; Liu Zhiyong

2012-01-01

As the core component of CITP-II, the online tritium production irradiation device is the pivotal equipment in the research on tritium production and release of tritium breeders. The design of CITP-II online tritium production irradiation device creatively makes replacing the breeders online come true; as tritium production capacity, the self-shielding factor of device, and neutron flux were studied. The influence of different load models and load thicknesses of breeders to tritium production capacity was calculated. The hydrodynamics parameters of device in solid-gas phase were computed. Thermal parameters, such as the heat power of breeders, hotspot, temperature grads distributions, utmost temperature, uneven factors, were analyzed. Creatively designed nonlinear electric heater equalized breeders' even heat power. The influence laws of the components, pressure of gap gas and carrier gas to the balance temperature were got. And the key thermal parameters were ascertained. The key thermal parameters and the changing laws were got and provide the basis for structural optimization and safety analysis. They can also be referenced for the study of breeders' tritium production and release. (authors)

User's manual for the ARMLID (Argonne metallic lithium/isotopic dilution) tritium assay system

International Nuclear Information System (INIS)

Porges, K.G.; Bretscher, M.M.; Bennett, E.F.; DiIorio, G.; Mattas, R.F.; Lewandowski, E.F.

1992-08-01

The Argonne Metallic Lithium - Isotopic Dilution (ARMLID) system described in this report, originally developed at ANL for other purposes, was recently redeployed to measure the tritium production rate (TPR) in a series of US/Japanese collaborative fusion blanket integral experiments, involving large assemblies of fusion breeder blanket materials that were irradiated with a fusion neutron source at FNS/JAERI, Japan. Whereas previous uses of the ARMUD scheme involved just a few samples, its application infusion blanket TPR mapping called for large sample numbers per experiment, implying a commensurate scale of sample fabrication and encapsulation, on one hand, and tritium extraction and counting on the other hand. To shorten the time required for these various tasks, yet still yield reliable and accurate results, both the sample fabrication - encapsulation facility and the tritium extraction system had to be extensively revised from original versions that were designed for accuracy, but not necessarily for speed. The present report describes overall revisions in sufficient detail to serve as a User's Manual for this facility, and/or suggest how a new system might be put together. Either possibility may develop in the near future, in support of ITER design studies. Preliminary and partial descriptions of various aspects and features of the system were presented orally, in the course of annual ANL/JAERI/UCLA ''workshops'', over the last 34 years, as well as elsewhere

Lithium aluminates and tritium production

International Nuclear Information System (INIS)

Carrera G, L.M.; Palacios G, O.; Bosch G, P.

1997-01-01

In this work it is studied the crystalline structure of lithium aluminates prepared by three different methods, namely: solid state reaction, humid reaction and sol-gel reaction. The analysis methods are the X-ray diffractometry and the scanning and transmission electron microscopy. This study is realized as in original materials as in irradiated materials at the TRIGA Mark reactor, to correlate the synthesis method with response of these materials to the mixed irradiation of nuclear reactor. (Author)

Tritium assay of Li2O pellets in the LBM/LOTUS experiments

International Nuclear Information System (INIS)

Quanci, J.; Azam, S.; Bertone, P.

1986-01-01

One of the objectives of the Lithium Blanket Module (LBM) program is to test the ability of advanced neutronics codes to model the tritium breeding characteristics of a fusion blanket exposed to a toroidal fusion neutron source. The LBM consists of over 20,000 cylindrical lithium oxide pellets and numerous diagnostic pellets and wafers. The LBM has been irradiated at the Ecole Polytechnique Federale de Lausanne (EPFL) LOTUS facility with a Haefely sealed neutron generator that gives a point deuterium-tritium neutron source up to 5 x 10 12 14-MeV n/s. Both Princeton Plasma Physics Lab. (PPPL) and EPFL assayed the tritium bred at various positions in the LBM. EPFL employed a dissolution technique while PPPL recovered the tritium by a thermal extraction method

Sublethal effects of tritium on aquatic systems. Ecological effects of lithium and beryllium on important aquatic organisms and associted communities. Teratogenic effects of low-level magnetic fields

International Nuclear Information System (INIS)

Strand, J.A.; Emery, R.M.

1980-01-01

Continuing studies of the sublethal effects of tritium on freshwater species emphasize the potential for genetic transmission of suppressed immune competence in offspring of parental rainbow trout (Salmo gairdneri) exposed to tritium (0, 0.04, 0.4, 40.0 rads) during embryogenesis. We plan to determine the relative biological effectiveness of tritium beta irradiation when compared to 60 Co gamma irradiation using the relatively radiosensitive immune process of rainbow trout. During FY 1979, we concluded genetic effects studies and prepared a manuscript for open literature publication summarizing FY 1977 and FY 1978 studies on the permanence of suppression of the primary immune response in rainbow trout sublethally irradiated during embryogenesis. We are also studying the potential effects of beryllium and lithium on aquatic systems. Because of mining and refining subsequent to the use of these metals in the construction of fusion reactors, increased levels of each are likely to be encountered in surface waters. Studies included an evaluation of potential toxicity of lithium on embryological life stages of rainbow trout and an assessment of fate and effects in artificial stream habitats. Levels of lithium necessary to cause an observed effect would have to be at least three orders of magnitude above observed background. Studies initiated in FY 1978 include evaluation of effects of low-level magnetic fields on embryologic development of rainbow trout. The objective of these studies to provide data useful in assessing potentially harmful effects of low-level magnetic fields encountered by attendant personnel working in the transport and hot cell areas of fusion reactors. This approach is less costly than using mammalian systems, provides large numbers of experimental organisms for meaningful statistical analysis and permits examination of potential latent effects in a representative vertebrate

The reprocessing of advanced mixed lithium orthosilicate/metatitanate tritium breeder pebbles

Energy Technology Data Exchange (ETDEWEB)

Leys, Oliver, E-mail: oliver.leys@kit.edu [Karlsruhe Institute of Technology, Institute for Applied Materials, Eggenstein-Leopoldshafen, 76344 (Germany); Bergfeldt, Thomas; Kolb, Matthias H.H.; Knitter, Regina [Karlsruhe Institute of Technology, Institute for Applied Materials, Eggenstein-Leopoldshafen, 76344 (Germany); Goraieb, Aniceto A. [Karlsruhe Beryllium Handling Facility, Eggenstein-Leopoldshafen, 76344 (Germany)

2016-06-15

Highlights: • The recycling of advanced breeder pebbles without a deterioration of the material properties is possible using a melt-based process. • The only accumulation of impurities upon reprocessing, results from the platinum crucible alloy used for processing. • It is possible to replenish burnt-up lithium by additions of LiOH·H{sub 2}O to the melt during reprocessing. - Abstract: The recycling of tritium breeding materials will be necessary for any future use of nuclear fusion energy due to economical as well as ecological considerations. In the case of the solid breeder blanket concept, the ceramic pebble beds that are intended for the generation of tritium will eventually need to be restored due to depleted lithium levels as well as due to fractured pebbles, which will cause a deterioration of the pebble bed properties. It is proposed that the pebbles, which are fabricated using a melt-based process, are recycled using the same initial process, by replenishing the lithium levels and reforming the pebbles at the same time. To prove this recycling scheme, advanced ceramic pebbles were fabricated and then re-melted multiple times to prove that the reprocessing did not have any negative effect on the pebble properties and secondly, pebbles were produced with a simulated lithium burn-up and subsequently replenished by additions of LiOH to the melt. It was shown that the re-melting and lithium re-enrichment had no effect on the pebble properties, demonstrating that a melt-based process is suitable for recycling used breeder pebbles.

Tritium diffusion in polycrystalline lithium tungstate

International Nuclear Information System (INIS)

Krutyakov, A.N.; Shadrin, A.A.; Saunin, E.I.; Gromov, V.V.; Shafiev, A.I.

1984-01-01

Using radiometric method the investigation of tritium separation from neutron irradiated (neutron flux density 1.2x10 13 n/cm 2 xs) polycrystalline Li 2 WO 4 in the temperature range 200-680 deg C has been carried out. It is established that the use of helium as gas-carrier of flow-type gas-discharge counter permits to conduct continuous stable measurements of concentrations of tritium extracted depending on its chemical state. It is shown that volume diffusion is the process, limiting tritiated particle separation rate from Li 2 WO 4 . It is found that the process of tritium volume diffusion in Li 2 WO 4 corresponds to two different mechanisms respectively in low- (200-300 deg C) and high-temperature (350-680 deg C) ranges. A supposition is made that in the low-temperature range the process of diffusion is conditioned by the dissociation of the radiation defect-tritiated particle complex, which is confirmed by the data on radiation defect annealing in Li 2 WO 4 . The value of activation energy of tritium separation process in the range 350-680 deg C, proved to be equal to 13.3 kJ/mol. Possible role of crystal structure peculiarities of Li 2 WO 4 for diffusion process is pointed out

Tritium and helium behavior in irradiated beryllium

International Nuclear Information System (INIS)

Billone, M.C.; Lin, C.C.; Baldwin, D.L.

1990-11-01

Large quantities of Be (> 100 metric tons) are planned for use in the ITER blanket design to enhance tritium breeding and to act as a thermal barrier between coolant and breeder. Tritium retention/release and He-induced swelling are important issues in blanket design. The data base on tritium and helium behavior in Be is reviewed. New data on tritium retention/release and He bubble growth are presented for Be irradiated to 5 x 10 22 n(E > 1 MeV)/cm 2 at ∼75 degree C and postirradiation-annealed for 700 hours at 500 degree C. A model (diffusion/desorption) is proposed and tested against the data base to determine tritium diffusivity and the desorption rate constant. Similarly a model for He-induced swelling is developed and tested against the data base. The dependence of tritium retention and release on He content and impurities (e.g. BeO) is also explored. 11 refs., 6 figs

Improvement of the model for surface process of tritium release from lithium oxide

International Nuclear Information System (INIS)

Yamaki, Daiju; Iwamoto, Akira; Jitsukawa, Shiro

2000-01-01

Among the various tritium transport processes in lithium ceramics, the importance and the detailed mechanism of surface reactions remain to be elucidated. The dynamic adsorption and desorption model for tritium desorption from lithium ceramics, especially Li 2 O was constructed. From the experimental results, it was considered that both H 2 and H 2 O are dissociatively adsorbed on Li 2 O and generate OH - on the surface. In the first model developed in 1994, it was assumed that either the dissociative adsorption of H 2 or H 2 O on Li 2 O generates two OH - on the surface. However, recent calculation results show that the generation of one OH - and one H - is more stable than that of two OH - s by the dissociative adsorption of H 2 . Therefore, assumption of H 2 adsorption and desorption in the first model is improved and the tritium release behavior from Li 2 O surface is evaluated again by using the improved model. The tritium residence time on the Li 2 O surface is calculated using the improved model, and the results are compared with the experimental results. The calculation results using the improved model agree well with the experimental results than those using the first model

Tritium-doping enhancement of polystyrene by ultraviolet laser and hydrogen plasma irradiation for laser fusion experiments

Energy Technology Data Exchange (ETDEWEB)

Iwasa, Yuki, E-mail: iwasa-y@ile.osaka-u.ac.jp [Institute of Laser Engineering, Osaka University, 2-6 Yamadaoka, Suita, Osaka 565-0871 (Japan); Yamanoi, Kohei; Iwano, Keisuke; Empizo, Melvin John F.; Arikawa, Yasunobu; Fujioka, Shinsuke; Sarukura, Nobuhiko; Shiraga, Hiroyuki; Takagi, Masaru; Norimatsu, Takayoshi; Azechi, Hiroshi [Institute of Laser Engineering, Osaka University, 2-6 Yamadaoka, Suita, Osaka 565-0871 (Japan); Noborio, Kazuyuki; Hara, Masanori; Matsuyama, Masao [Hydrogen Isotope Research Center, Organization for Promotion of Research, University of Toyama, 3190 Gofuku, Toyama 930-8555 (Japan)

2016-11-15

Highlights: • Tritium-doped polystyrene films are fabricated by the Wilzbach method with UV laser and hydrogen plasma irradiation. • The 266-nm laser-irradiated, 355-nm laser-irradiated, and hydrogen plasma-irradiated polystyrene films exhibit higher PSL intensities and specific radioactivities than the non-irradiated sample. • Tritium doping by UV laser irradiation can be largely affected by the laser wavelength because of polystyrene’s absorption. • Hydrogen plasma irradiation results to a more uniform doping concentration even at low partial pressure and short irradiation time. • UV laser and plasma irradiations can be utilized to fabricate tritium-doped polystyrene shell targets for future laser fusion experiments. - Abstract: We investigate the tritium-doping enhancement of polystyrene by ultraviolet (UV) laser and hydrogen plasma irradiation. Tritium-doped polystyrene films are fabricated by the Wilzbach method with UV laser and hydrogen plasma. The 266-nm laser-irradiated, 355-nm laser-irradiated, and hydrogen plasma-irradiated polystyrene films exhibit higher PSL intensities and specific radioactivities than the non-irradiated sample. Tritium doping by UV laser irradiation can be largely affected by the laser wavelength because of polystyrene’s absorption. In addition, UV laser irradiation is more localized and concentrated at the spot of laser irradiation, while hydrogen plasma irradiation results to a more uniform doping concentration even at low partial pressure and short irradiation time. Both UV laser and plasma irradiations can nevertheless be utilized to fabricate tritium-doped polystyrene targets for future laser fusion experiments. With a high doping rate and efficiency, a 1% tritium-doped polystyrene shell target having 7.6 × 10{sup 11} Bq g{sup −1} specific radioactivity can be obtained at a short period of time thereby decreasing tritium consumption and safety management costs.

Tritium and helium retention and release from irradiated beryllium

Energy Technology Data Exchange (ETDEWEB)

Anderl, R.A.; Longhurst, G.R.; Oates, M.A.; Pawelko, R.J. [Idaho National Engineering and Environmental Lab., Idaho Falls, ID (United States)

1998-01-01

This paper reports the results of an experimental effort to anneal irradiated beryllium specimens and characterize them for steam-chemical reactivity experiments. Fully-dense, consolidated powder metallurgy Be cylinders, irradiated in the EBR-II to a fast neutron (>0.1 MeV) fluence of {approx}6 x 10{sup 22} n/cm{sup 2}, were annealed at temperatures from 450degC to 1200degC. The releases of tritium and helium were measured during the heat-up phase and during the high-temperature anneals. These experiments revealed that, at 600degC and below, there was insignificant gas release. Tritium release at 700degC exhibited a delayed increase in the release rate, while the specimen was at 700degC. For anneal temperatures of 800degC and higher, tritium and helium release was concurrent and the release behavior was characterized by gas-burst peaks. Essentially all of the tritium and helium was released at temperatures of 1000degC and higher, whereas about 1/10 of the tritium was released during the anneals at 700degC and 800degC. Measurements were made to determine the bulk density, porosity and specific surface area for each specimen before and after annealing. These measurements indicated that annealing caused the irradiated Be to swell, by as much as 14% at 700degC and 56% at 1200degC. Kr gas adsorption measurements for samples annealed at 1000degC and 1200degC determined specific surface areas between 0.04 m{sup 2}/g and 0.1 m{sup 2}/g for these annealed specimens. The tritium and helium gas release measurements and the specific surface area measurements indicated that annealing of irradiated Be caused a porosity network to evolve and become surface-connected to relieve internal gas pressure. (author)

The effect of neutron irradiation on the trapping of tritium in carbon-based materials

International Nuclear Information System (INIS)

Kwast, H.; Werle, H.; Glugla, M.; Wu, C.H.; Federici, G.

1993-11-01

Carbon-based materials are considered for protection of plasma facing components in the next step fusion device. To investigate the effects of neutron damage on the tritium behaviour an experimental study on the tritium retention of various neutron irradiated graphites and carbon/carbon fibre composites was started. The irradiation dose of the specimens ranges from 10 -3 to 3.5 dpa.g and the irradiation temperature from 390 C to 1500 C. A comparison of tritium retention in pre- and post-irradiated carbon-based materials as a function of the sample temperature is reported in this paper and the results are discussed. The first results indicate that the retention of tritium is higher in irradiated graphite than in unirradiated graphite and depends largely on the density and microstructure. The retention is also influenced by the tritium-loading temperature. Graphite of type S 1611, irradiated at 400 C and 600 C up to a damage of 0.1 dpa.g, retained about two times more tritium than the unirradiated material. (orig.)

Phase transformations in lithium aluminates irradiated with neutrons; Transformaciones de fase en aluminatos de litio irradiados con neutrones

Energy Technology Data Exchange (ETDEWEB)

Carrera, L.M.; Delfin L, A.; Urena N, F.; Basurto, R. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico); Bosch, P. [UAM-I, 09340 Mexico D.F. (Mexico)

2003-07-01

The lithium aluminate like candidate to be used in the coverings producers of tritium in the fusion nuclear reactors, presents high resistance to the corrosion to the one to be stuck to structural materials as special steels. However, the crystallographic changes that take place in the cover that is continually subjected to irradiation with neutrons, can alter its resistance to the corrosion. In this work the changes of crystalline structure are shown that they present two types of nano structures of lithium aluminates, subjected to an average total dose 7.81 x 10{sup 8} Gy in the fixed irradiation system of capsules of the one TRIGA Mark lll nuclear reactor of the Nuclear Center of Mexico. The studied nano structures presented only phase transformations without formation of amorphous material. (Author)

Evaluation of cermet materials suitable for lithium lubricated thrust bearings for high temperature operation

Science.gov (United States)

Sinclair, J. H.; Hendrixson, W. H.

1974-01-01

Cerment materials (HfC - 10 wt% W; HfC - 10 wt% TaC - 10 wt%W; HfC - 2 wt% CbC - 8 wt% Mo;Hfn - 10 wt% W; Hfn - 10 wt% TaN - 10 wt% W; and ZrC - 17 wt% W) were evaluated for possible use as lithium-lubricated bearings in the control system of a nuclear reactor. Tests of compatibility with lithium were made in T-111 (Ta-8W-2Hf) capsules at temperatures up to 1090 C. The tendencies of HfC-TaC-W, HfC-CbC-Mo, and HfN-W to bond to themselves and to the refractory alloys T-111 and TZM when enclosed in lithium-filled capsules under a pressure of 2000 psi at 980 and 1200 C for 1933 hours were evaluated. Thermal expansion characteristics were determined for the same three materials from room temperature to 1200 C. On the basis of these tests, HfC-10 TaC-10W and HfN-10W were selected as the best and second best candidates, respectively, of the materials tested for the bearing application.

Results of preliminary experiments on tritium decontamination by UV irradiation

International Nuclear Information System (INIS)

Oya, Yasuhisa; Shu, Wataru; O'hira, Shigeru; Hayashi, Takumi; Nishi, Masataka

2000-03-01

In the point of view of protection of workers from the radiation exposure and the limitation of the contamination with radioactive materials, it is important to decontaminate mobile tritium from plasma facing components of a nuclear fusion reactor at the beginning of their maintenance work. It is considered that the heating is the most effective method for decontamination. However, it is important to develop new decontamination method of adsorbed hydro-carbon based substances from the materials that cannot be heated or the inner pipe of double pipes. This report presents results of preliminary experiments performed for the development of the effective tritium decontamination technique pursuing under US/Japan collaborative program on technology for fusion-fuel processing (Annex IV). In the experiments, the effects of Ultra Violet (UV) irradiation on tritium removal from some kinds of materials, such as poly vinyl chloride -(CH 2 CHCl) n - film, polyethylene film and graphite samples coated by C 2 H 2 plasma were examined. As the result of UV irradiation, it was confined that hydrogen and carbon based compounds could be released from the specimen during UV irradiation. It is concluded that UV irradiation is one of the hopeful candidates for effective tritium decontamination. (author)

PRODUCTION OF TRITIUM

Science.gov (United States)

Jenks, G.H.; Shapiro, E.M.; Elliott, N.; Cannon, C.V.

1963-02-26

This invention relates to a process for the production of tritium by subjecting comminuted solid lithium fluoride containing the lithium isotope of atomic mass number 6 to neutron radiation in a self-sustaining neutronic reactor. The lithium fiuoride is heated to above 450 deg C. in an evacuated vacuum-tight container during radiation. Gaseous radiation products are withdrawn and passed through a palladium barrier to recover tritium. (AEC)

The requirements for processing tritium recovered from liquid lithium blankets: The blanket interface

International Nuclear Information System (INIS)

Clemmer, R.G.; Finn, P.A.; Greenwood, L.R.; Grimm, T.L.; Sze, D.K.; Bartlit, J.R.; Anderson, J.L.; Yoshida, H.; Naruse.

1988-03-01

We have initiated a study to define a blanket processing mockup for Tritium Systems Test Assembly. Initial evaluation of the requirements of the blanket processing system have been started. The first step of the work is to define the condition of the gaseous tritium stream from the blanket tritium recovery system. This report summarizes this part of the work for one particular blanket concept, i.e., a self-cooled lithium blanket. The total gas throughput, the hydrogen to tritium ratio, the corrosive chemicals, and the radionuclides are defined. The key discoveries are: the throughput of the blanket gas stream (including the helium carrier gas) is about two orders of magnitude higher than the plasma exhaust stream;the protium to tritium ratio is about 1, the deuterium to tritium ratio is about 0.003;the corrosion chemicals are dominated by halides;the radionuclides are dominated by C-14, P-32, and S-35;their is high level of nitrogen contamination in the blanket stream. 77 refs., 6 figs., 13 tabs

Tritium breeders and tritium permeation barrier coatings for fusion reactor

International Nuclear Information System (INIS)

Yamawaki, Michio; Kawamura, Hiroshi; Tsuchiya, Kunihiko

2004-01-01

A state of R and D of tritium breeders and tritium permeation barrier coatings for fusion reactor is explained. A list of candidate for tritium breeders consists of ceramics containing lithium, for examples, Li 2 O, Li 2 TiO 3 , Li 2 ZrO 3 , Li 4 SiO 4 and LiAlO 2 . The characteristics and form are described. The optimum particle size is from 1 to 10 μm. The production technologies of tritium breeders in the world are stated. Characteristics of ceramics with lithium as tritium breeders are compared. TiC, TiN/TiC, Al 2 O 3 and Cr 2 O 3 -SiO 2 -P 2 O 5 are tritium permeation barrier coating materials. These production methods and evaluation of characteristics are explained. (S.Y.)

Cost of generating tritium internal and external to a tokamak hybrid reactor

International Nuclear Information System (INIS)

Crotzer, M.E.; Heck, F.M.; Steinke, K.C.

1981-01-01

The costs associated with producing tritium internal and external to a thorium-based tokamak hybrid are estimated for a number of scenarios and the resulting impact on the symbiotic system cost of electricity calculated. For tritium generation within the hybrid, both continuous and batch production is analyzed. For external production, the lithium-bearing blanket is replaced with thorium and the tritium is generated in the client fission reactors. Continuous tritium production within the hybrid is found to increase the cost of electricity from 1.4 to 4.0 mills/kW-h. Batch tritium production can increase the cost of electricity by 10 mills/kW-h. Producing tritium outside the hybrid, and thereby enhancing client support, increases the cost of electricity from 1.8 to 4.1 mills/kW-h

Tritium release from EXOTIC-7 orthosilicate pebbles. Effect of burnup and contact with beryllium during irradiation

Energy Technology Data Exchange (ETDEWEB)

Scaffidi-Argentina, F; Werle, H [Forschungszentrum Karlsruhe GmbH Technik und Umwelt (Germany). Inst. fuer Neutronenphysik und Reaktortechnik

1998-03-01

EXOTIC-7 was the first in-pile test with {sup 6}Li-enriched (50%) lithium orthosilicate (Li{sub 4}SiO{sub 4}) pebbles and with DEMO representative Li-burnup. Post irradiation examinations of the Li{sub 4}SiO{sub 4} have been performed at the Forschungszentrum Karlsruhe (FZK), mainly to investigate the tritium release kinetics as well as the effect of Li-burnup and/or contact with beryllium during irradiation. The release rate of Li{sub 4}SiO{sub 4} from pure Li{sub 4}SiO{sub 4} bed of capsule 28.1-1 is characterized by a broad main peak at about 400degC and by a smaller peak at about 800degC, and that from the mixed beds of capsule 28.2 and 26.2-1 shows again these two peaks, but most of the tritium is now released from the 800degC peak. This shift of release from low to high temperature may be due to the higher Li-burnup and/or due to contact with Be during irradiation. Due to the very difficult interpretation of the in-situ tritium release data, residence times have been estimated on the basis of the out-of-pile tests. The residence time for Li{sub 4}SiO{sub 4} from caps. 28.1-1 irradiated at 10% Li-burnup agrees quite well with that of the same material irradiated at Li-burnup lower than 3% in the EXOTIC-6 experiment. In spite of the observed shift in the release peaks from low to high temperature, also the residence time for Li{sub 4}SiO{sub 4} from caps. 26.2-1 irradiated at 13% Li-burnup agrees quite well with the data from EXOTIC-6 experiment. On the other hand, the residence time for Li{sub 4}SiO{sub 4} from caps. 28.2 (Li-burnup 18%) is about a factor 1.7-3.8 higher than that for caps. 26.2-1. Based on these data on can conclude that up to 13% Li-burnup neither the contact with beryllium nor the Li-burnup have a detrimental effect on the tritium release of Li{sub 4}SiO{sub 4} pebbles, but at 18% Li-burnup the residence time is increased by about a factor three. (J.P.N.)

Present status of irradiation tests on tritium breeding blanket for fusion reactor

International Nuclear Information System (INIS)

Futamura, Yoshiaki; Sagawa, Hisashi; Shimakawa, Satoshi; Tsuchiya, Kunihiko; Kuroda, Toshimasa; Kawamura, Hiroshi.

1994-01-01

To develop a tritium breeding blanket for a fusion reactor, irradiation tests in fission reactors are indispensable for obtaining data on irradiation effects on materials, and neutronics/thermal characteristics and tritium production/recovery performance of the blanket. Various irradiation tests have been conducted in the world, especially to investigate tritium release characteristics from tritium breeding and neutron multiplier materials, and materials integrity under irradiation. In Japan, VOM experiments at JRR-2 for ceramic breeders and experiments at JMTR for ceramic breeders and beryllium as a neutron multiplier have been performed. Several universities have also investigated ceramic breeders. In the EC, the EXOTIC experiments at HFR in the Netherlands and the SIBELIUS, the LILA, the LISA and the MOZART experiments for ceramic breeders have carried out. In Canada, NRU has been used for the CRITIC experiments. The TRIO experiments at ORR(ORNL), experiments at RTNS-II, FUBR and ATR have been conducted in the USA. The last two are experiments with high neutron fluence aiming at investigating materials integrity under irradiation. The BEATRIX-I and -II experiments have proceeded under international collaboration of Japan, Canada, the EC and the USA. This report shows the present status of these irradiation tests following a review of the blanket design in the ITER CDA(Conceptual Design Activity). (author)

Equilibrium and Kinetic Studies of Systems of Hydrogen Isotopes, Lithium Hydrides, Aluminum and LiAlO2

International Nuclear Information System (INIS)

Owen, J.H.

2001-01-01

This paper described measurements of (1) the distribution of tritium and helium throughout both phases of irradiated Li-Al alloy, (2) the migration rate of tritium during moderate heating, (3) equilibrium pressures as functions of temperature of H2, D2, or T2 in contact with lithium hydrides + aluminum, Li-Al alloy, or irradiated Li-Al alloy, (4) the equilibrium constant for the reaction as a function of temperature, and (5) extraction rates of tritium from irradiated LiAlO2 targets at elevated temperatures

Tritium release kinetics of Li{sub 2}O with radiation defects

Energy Technology Data Exchange (ETDEWEB)

Grishmanov, V; Tanaka, Satoru [Tokyo Univ. (Japan). Faculty of Engineering

1998-03-01

The study of an influence of radiation defects on tritium release behavior from polycrystalline Li{sub 2}O was performed by the in-pile and out-of-pile tritium release experiments. The samples were pre-irradiated by accelerated electrons to various absorbed doses up to 140 MGy and then exposed to the fluence of 10{sup 17} thermal neutrons/m{sup 2}. The radiation defects introduced by electron irradiation in Li{sub 2}O cause the retention of tritium. The linear temperature increase of the electron-irradiated samples disclosed two tritium release peaks: first starts at {approx}600 K with the maximum at {approx}800 K and second appears at {approx}950 K with the maximum at {approx}1200 K. It is thought that the tritium release at high temperatures (> 950 K) is due to the thermal decomposition of LiT. In order to further investigated the formation of lithium hydrides, the diffuse-reflectance Fourier transform infrared (FTIR) absorption spectroscopy was applied. The Li{sub 2}O powder was irradiated by electron accelerator under D{sub 2} containing atmosphere (N{sub 2} + 10% D{sub 2}). An absorption band specific to the Li{sub 2}O was observed at 668 cm{sup -1} and attributed to the Li-D stretching vibration. (author)

Tritium release from neutron-irradiated Li2O: Transport in porous sintered pellets

International Nuclear Information System (INIS)

Tanifuji, Takaaki; Yamaki, Daiju; Jitsukawa, Shiro

2006-01-01

The tritium release behavior from Li 2 O sintered pellets (81-88% T.D.) is examined by isothermal heating tests. (1) For the 88% T.D. specimens, the fraction of residual tritium is found to follow the square-root law of the annealing time. The rate-determining process is the migration in the connected micro-pore. (2) For the 81% T.D. specimens, which are annealed after irradiation at 630 K for 4 h, the fraction of residual tritium is also found to follow the square-root law of the annealing time. The rate-determining process is the migration in the connected micro-pore. (3) For the 81% T.D. specimens as irradiated, the tritium release rate is found to follow the square-root law of the annealing time. The rate-determining process is controlled by Kohlrauch stretched exponential form. Tritium trapped in irradiation defects released with recovering the defects by isothermal heating

Lithium zirconate elements fabricated by industrial scale processes

International Nuclear Information System (INIS)

Roux, N.

1991-01-01

Lithium metazirconate Li 2 ZrO 3 is one of the leading tritium breeding ceramics contemplated in solid blanket concepts for fusion reactors. Among its merits are fair physical properties, satisfactory compatibility with structural materials and beryllium, satisfactory mechanical strength, excellent irradiation behaviour as shown by a comparative irradiation of ceramics in the EBR II reactor, and very good tritium release performance as evidenced in the MOZART and EXOTIC neutron irradiations. Pechiney and the CEA are jointly involved in developing industrial fabrication of Li 2 ZrO 3 elements to the microstructural and geometrical specifications required for their use in the solid blankets as conceived in the European Program

Influence of radiation defects on tritium release parameters from Li2O

International Nuclear Information System (INIS)

Grishmanov, V.; Tanaka, S.; Yoneoka, T.

1998-01-01

The study of the influence of radiation defects on tritium release behavior from polycrystalline Li 2 O was performed by simultaneous measurements of the luminescence emission and tritium release. It was found that the radiation defects in Li 2 O introduced by electron irradiation cause the retention of tritium. It is thought that the tritium recovery is affected by the formation of a Li-T bond, which is tolerant of high temperatures. The retardation of tritium decreases with increasing absorbed dose in the dose range from 50 to 140 MGy. The aggregation of radiation defects at high irradiation doses is considered to be responsible for the decrease of the interaction of tritium with radiation defects. The mechanism of the interaction of radiation defects with tritium is discussed. (orig.)

Tritium transport calculations for the IFMIF Tritium Release Test Module

Energy Technology Data Exchange (ETDEWEB)

Freund, Jana, E-mail: jana.freund@kit.edu; Arbeiter, Frederik; Abou-Sena, Ali; Franza, Fabrizio; Kondo, Keitaro

2014-10-15

Highlights: • Delivery of material data for the tritium balance in the IFMIF Tritium Release Test Module. • Description of the topological models in TMAP and the adapted fusion-devoted Tritium Permeation Code (FUS-TPC). • Computation of release of tritium from the breeder solid material into the purge gas. • Computation of the loss of tritium over the capsule wall, rig hull, container wall and purge gas return line. - Abstract: The IFMIF Tritium Release Test Module (TRTM) is projected to measure online the tritium release from breeder ceramics and beryllium pebble beds under high energy neutron irradiation. Tritium produced in the pebble bed of TRTM is swept out continuously by a purge gas flow, but can also permeate into the module's metal structures, and can be lost by permeation to the environment. According analyses on the tritium inventory are performed to support IFMIF plant safety studies, and to support the experiment planning. This paper describes the necessary elements for calculation of the tritium transport in the Tritium Release Test Module as follows: (i) applied equations for the tritium balance, (ii) material data from literature and (iii) the topological models and the computation of the five different cases; namely release of tritium from the breeder solid material into the purge gas, loss of tritium over the capsule wall, rig hull, container wall and purge gas return line in detail. The problem of tritium transport in the TRTM has been studied and analyzed by the Tritium Migration Analysis Program (TMAP) and the adapted fusion-devoted Tritium Permeation Code (FUS-TPC). TMAP has been developed at INEEL and now exists in Version 7. FUS-TPC Code was written in MATLAB with the original purpose to study the tritium transport in Helium Cooled Lead Lithium (HCLL) blanket and in a later version the Helium Cooled Pebble Bed (HCPB) blanket by [6] (Franza, 2012). This code has been further modified to be applicable to the TRTM. Results from the

Tritium transport calculations for the IFMIF Tritium Release Test Module

International Nuclear Information System (INIS)

Freund, Jana; Arbeiter, Frederik; Abou-Sena, Ali; Franza, Fabrizio; Kondo, Keitaro

2014-01-01

Highlights: • Delivery of material data for the tritium balance in the IFMIF Tritium Release Test Module. • Description of the topological models in TMAP and the adapted fusion-devoted Tritium Permeation Code (FUS-TPC). • Computation of release of tritium from the breeder solid material into the purge gas. • Computation of the loss of tritium over the capsule wall, rig hull, container wall and purge gas return line. - Abstract: The IFMIF Tritium Release Test Module (TRTM) is projected to measure online the tritium release from breeder ceramics and beryllium pebble beds under high energy neutron irradiation. Tritium produced in the pebble bed of TRTM is swept out continuously by a purge gas flow, but can also permeate into the module's metal structures, and can be lost by permeation to the environment. According analyses on the tritium inventory are performed to support IFMIF plant safety studies, and to support the experiment planning. This paper describes the necessary elements for calculation of the tritium transport in the Tritium Release Test Module as follows: (i) applied equations for the tritium balance, (ii) material data from literature and (iii) the topological models and the computation of the five different cases; namely release of tritium from the breeder solid material into the purge gas, loss of tritium over the capsule wall, rig hull, container wall and purge gas return line in detail. The problem of tritium transport in the TRTM has been studied and analyzed by the Tritium Migration Analysis Program (TMAP) and the adapted fusion-devoted Tritium Permeation Code (FUS-TPC). TMAP has been developed at INEEL and now exists in Version 7. FUS-TPC Code was written in MATLAB with the original purpose to study the tritium transport in Helium Cooled Lead Lithium (HCLL) blanket and in a later version the Helium Cooled Pebble Bed (HCPB) blanket by [6] (Franza, 2012). This code has been further modified to be applicable to the TRTM. Results from the

Tritium problems in fusion reactor systems

International Nuclear Information System (INIS)

Hickman, R.G.

1975-01-01

A brief introduction is given to the role tritium will play in the development of fusion power. The biological and worldwide environmental behavior of tritium is reviewed. The tritium problems expected in fusion power reactors are outlined. A few thoughts on tritium permeation and recent results for tritium cleanup and CT 4 accumulation are presented. Problems involving the recovery of tritium from the breeding blanket in fusion power reactors are also considered, including the possible effect of impurities in lithium blankets and the use of lithium as a regenerable getter pump. (auth)

Bubble formation in irradiated Li2O

International Nuclear Information System (INIS)

Verrall, R.A.; Rose, D.H.; Miller, J.M.; Hastings, I.J.; MacDonald, D.S.

1991-01-01

Lithium oxide, irradiated to a burnup of 1 at% (total lithium) at temperatures between 400 and 850deg C with on-line tritium recovery and measurement, has been examined out-reactor. Residual tritium content ranged from 2.4 to 16 mCi/g, but, conservatively, averaged less than 10 mCi/g or 1 wppm. Scanning electron microscopy showed bubble formation in the ceramic which is thought to be due to helium formed from the in-reactor 6 Li(n, α) 3 H reaction. (orig.)

Development of a low tritium partial pressure permeation system for mass transport measurement in lead lithium eutectic

International Nuclear Information System (INIS)

Pawelko, R.; Shimada, M.; Katayama, K.; Fukada, S.; Terai, T.

2014-01-01

A new experimental system designed to investigate tritium mass transfer properties in materials important to fusion technology is operational at the Safety and Tritium Applied Research (STAR) facility located at the Idaho National Laboratory (INL). The tritium permeation measurement system was developed as part of the Japan/US TITAN collaboration to investigate tritium mass transfer properties in liquid lead lithium eutectic (LLE) alloy. The system is similar to a hydrogen/deuterium permeation measurement system developed at Kyushu University and also incorporates lessons learned from previous tritium permeation experiments conducted at the STAR facility. This paper describes the experimental system that is configured specifically to measure tritium mass transfer properties at low tritium partial pressures. We present preliminary tritium permeation results for α-Fe and α-Fe/LLE samples at 600degC and at tritium partial pressures between 1.0E-3 and 2.4 Pain helium. The preliminary results are compared with literature data. (author)

Tritium assay of Li/sub 2/O in the LBM/LOTUS experiments

International Nuclear Information System (INIS)

Quanci, J.; Azam, S.; Bertone, P.

1986-01-01

The Lithium Blanket Module (LBM) is an assembly of over 20,000 cylindrical lithium oxide pellets in an array representative of a limited-coverage breeding zone for a toroidal fusion device. A principal objective of the LBM program is to test the ability of advanced neutronics coding to model the tritium breeding characteristics of a fusion device blanket. The LBM has been irradiated at the Ecole Polytechnique Federale de Lausanne (EPFL) LOTUS facility with a 14 MeV point-neutron source. Princeton Plasma Physics Laboratory (PPPL) and EPFL assayed the tritium bred in lithium oxide diagnostic samples placed at various positions in the LBM. PPPL employed a thermal extraction technique while EPFL used a dissolution method. The results for the assay are reported and compared to MCNP Monte Carlo neutronics calculations for the LBM/LOTUS system

Tritium control in fusion reactor materials: A model for Tritium Extracting System

International Nuclear Information System (INIS)

Zucchetti, Massimo; Utili, Marco; Nicolotti, Iuri; Ying, Alice; Franza, Fabrizio; Abdou, Mohamed

2015-01-01

Highlights: • A modeling work has been performed to address these issues in view of its utilization for the TES (Tritium Extraction System), in the case of the HCPB TBM and for a Molecular sieve as adsorbent material. • A computational model has been setup and tested in this paper. • The results of experimental measurement of fundamental parameters such as mass transfer coefficients have been implemented in the model. • It turns out the capability to model the extraction process of gaseous tritium compounds and to estimate the breakthrough curves of the two main tritium gaseous species (H2 and HT). - Abstract: In fusion reactors, tritium is bred by lithium isotopes inside the blanket and then extracted. However, tritium can contaminate the reactor structures, and can be eventually released into the environment. Tritium in reactor components should therefore be kept under close control throughout the fusion reactor lifetime, bearing in mind the risk of accidents, the need for maintenance and the detritiation of dismantled reactor components before their re-use or disposal. A modeling work has been performed to address these issues in view of its utilization for the TES (Tritium Extraction System), in the case of the HCPB TBM and for a molecular sieve as adsorbent material. A computational model has been setup and tested. The results of experimental measurement of fundamental parameters such as mass transfer coefficients have been implemented in the model. It turns out the capability of the model to describe the extraction process of gaseous tritium compounds and to estimate the breakthrough curves of the two main tritium gaseous species (H2 and HT).

Tritium control in fusion reactor materials: A model for Tritium Extracting System

Energy Technology Data Exchange (ETDEWEB)

Zucchetti, Massimo [DENERG, Politecnico di Torino (Italy); Utili, Marco, E-mail: marco.utili@enea.it [ENEA UTIS – C.R. Brasimone, Bacino del Brasimone, Camugnano, BO (Italy); Nicolotti, Iuri [DENERG, Politecnico di Torino (Italy); Ying, Alice [University of California Los Angeles (UCLA), Los Angeles, CA (United States); Franza, Fabrizio [Karlsruhe Institute of Technology, Karlsruhe (Germany); Abdou, Mohamed [University of California Los Angeles (UCLA), Los Angeles, CA (United States)

2015-10-15

Highlights: • A modeling work has been performed to address these issues in view of its utilization for the TES (Tritium Extraction System), in the case of the HCPB TBM and for a Molecular sieve as adsorbent material. • A computational model has been setup and tested in this paper. • The results of experimental measurement of fundamental parameters such as mass transfer coefficients have been implemented in the model. • It turns out the capability to model the extraction process of gaseous tritium compounds and to estimate the breakthrough curves of the two main tritium gaseous species (H2 and HT). - Abstract: In fusion reactors, tritium is bred by lithium isotopes inside the blanket and then extracted. However, tritium can contaminate the reactor structures, and can be eventually released into the environment. Tritium in reactor components should therefore be kept under close control throughout the fusion reactor lifetime, bearing in mind the risk of accidents, the need for maintenance and the detritiation of dismantled reactor components before their re-use or disposal. A modeling work has been performed to address these issues in view of its utilization for the TES (Tritium Extraction System), in the case of the HCPB TBM and for a molecular sieve as adsorbent material. A computational model has been setup and tested. The results of experimental measurement of fundamental parameters such as mass transfer coefficients have been implemented in the model. It turns out the capability of the model to describe the extraction process of gaseous tritium compounds and to estimate the breakthrough curves of the two main tritium gaseous species (H2 and HT).

Tritium recovery from fusion blankets using solid lithium compounds. I. Design and minimization of tritium inventory

International Nuclear Information System (INIS)

Powell, J.R.

1975-01-01

Tritium blanket inventories of 100 curies/MW(e) are readily achievable, and inventories as low as 10 curies/MW(e) are possible for blankets with small lithium compound particulates (less than or equal to 50μ) at T greater than or equal to 800 0 C. Of the three release modes [A - to the main coolant (e.g., He) stream; B - to a separate processing circuit; and C - to the plasma region], mode A appears optimum for blankets using gas-cooled metallic structures (e.g., Al, stainless), while mode C appears optimum for high temperature refractory (e.g., C, SiC) structures. The greater structural complexity of mode B makes it less attractive than modes A and C. No recovery method is required for mode C release. With mode A release, tritium inventory in the coolant circuits ranges from 1 to 10 curies/MW(e), depending on processing parameters. Tritium leak rates to the environment during normal operation can be kept to less than or equal to 10 -3 curies/MW(e) per day with low permeability barriers. In general, a mixture of T 2 and T 2 O is present in the coolant stream. Three methods of tritium recovery are examined: (1) Conversion to T 2 followed by absorption in a metal hydride bed. (2) Conversion to T 2 followed by condensation at approximately 6 0 K. (3) Conversion to T 2 O followed by condensation at approximately 100 0 K

Analysis and speciation of the tritium in environmental matrices

International Nuclear Information System (INIS)

Bacchetta, Audrey

2014-01-01

This study deals with environmental monitoring. The main aims are (i) the optimisation of the analytical procedure for the tritium in organic form determination, and (ii) the identification of the tritium bearing molecules which are responsible for its transfer from the environment to man. The study was divided into three stages. First an analytical method was developed to determine hydrogen content of several samples, which is a key element to calculate accurate organically bound tritium activities. Secondly, the impact of the organically bound tritium fractions separation (labile exchange) for the determination of the representative fraction of the level of environmental tritium activity was then evaluated. For that, the amount of solubilised sample was estimated. Finally, the speciation of tritium in environmental samples was investigated. Several molecules classes and organic compounds dissolved in the labile exchanges solvent were identified. The results show that the distribution of tritium in organisms depends on both properties of the chemical bond in which it is involved and chemical properties of tritium bearing molecules. The identified compounds belong to the molecules classes such as carbohydrates or amino acids, constitutive of living organisms. It would now be of interest to study the tritium distribution in an environmental sample to target molecules of interest and study the impact of tritium from the environment to man. (author) [fr

Tritium management in fusion synfuel designs

International Nuclear Information System (INIS)

Galloway, T.R.

1980-01-01

Two blanket types are being studied: a lithium-sodium pool boiler and a lithium-oxide- or lithium-sodium pool boiler and a lithium-oxide- or aluminate-microsphere moving bed. For each, a wide variety of current technology was considered in handling the tritium. Here, we show the pool boiler with the sulfur-iodine thermochemical cycle first developed and now being piloted by the General Atomic Company. The tritium (T 2 ) will be generated in the lithium-sodium mixture where the concentration is approx. 10 ppM and held constant by a scavenging system consisting mainly of permeators. An intermediate sodium loop carries the blanket heat to the thermochemical cycle, and the T 2 in this loop is held to 1 ppM by a similar scavenging system. With this design, we have maintained blanket inventory at 1 kg of tritium, kept thermochemical cycle losses to 5 Ci/d and environmental loss to 10 Ci/d, and held total plant risk inventory at 7 kg tritium

Tritium permeation barriers in contact with liquid lithium-lead eutectic (Pb-17Li)

International Nuclear Information System (INIS)

Forcey, K.S.; Perujo, A.

1995-01-01

The permeation of deuterium through coated stainless steel tubes containing liquid lithium-lead eutectic (Pb-17Li) has been studied and compared to measurements through tubes without the lithium compound. The measurements form part of an investigation into the effect of a potential tritium breeder material on permeation barriers for fusion reactors. The coatings studied were CVD TiC and Al 2 O 3 and a pack aluminised layer. Without the lithium-lead, the CVD coatings reduced the permeation rate up to 1 order of magnitude, and the aluminised layer up to 2 orders of magnitude. A CVD layer was unaffected by Pb-17Li whilst in the case of the aluminised tube, the lithium-lead completely removed the permeation barrier, presumably by attacking the surface oxide. Furthermore, the aluminised sample presented a large number of cracks and poor adheren ce to the substrate. ((orig.))

Analysis of in-pile tritium release experiments

International Nuclear Information System (INIS)

Kopasz, J.P.; Tam, S.W.; Johnson, C.E.

1992-01-01

The objective of this work is to characterize tritium release behavior from lithium ceramics and develop insight into the underlying tritium release mechanisms. Analysis of tritium release data from recent laboratory experiments with lithium aluminate has identified physical processes which were previously unaccounted for in tritium release models. A new model that incorporates the recent data and provides for release from multiple sites rather than only one site was developed. Calculations of tritium release using this model are in excellent agreement with the tritium release behavior reported for the MOZART experiment

Evaluation of tritium release behavior from Li{sub 2}TiO{sub 3} during DT neutron irradiation by use of an improved tritium collection method

Energy Technology Data Exchange (ETDEWEB)

Edao, Yuki, E-mail: edao.yuki@jaea.go.jp [Tritium Technology Group, Department of Blanket Systems Research, Rokkasho Fusion Institute, Sector of Fusion Research and Development, Japan Atomic Energy Agency, 2-4 Shirane Shirakata, Tokai-mura, Naka-gun, Ibaraki 319-1195 (Japan); Kawamura, Yoshinori [Blanket Technology Group, Department of Blanket Systems Research, Rokkasho Fusion Institute, Sector of Fusion Research and Development, Japan Atomic Energy Agency, 801-1 Mukoyama, Naka, Ibaraki 311-0193 (Japan); Hoshino, Tsuyoshi [Breeding Functional Materials Development Group, Department of Blanket Systems Research, Rokkasho Fusion Institute, Sector of Fusion Research and Development, Japan Atomic Energy Agency, 2-166 Omotedate Obuchi, Rokkasho, Aomori 039-3212 (Japan); Ochiai, Kentaro [BA Project Coordination Group, Department of Fusion Power Systems Research, Rokkasho Fusion Institute, Sector of Fusion Research and Development, Japan Atomic Energy Agency, 2-166 Omotedate Obuchi, Rokkasho, Aomori 039-3212 (Japan)

2016-11-15

Highlights: • Behavior of tritium released from Li{sub 2}TiO{sub 3} under neutron irradiation was measured. • Tritium collection method with hydrophobic catalyst was demonstrated successfully. • Temperature of Li{sub 2}TiO{sub 3} was dominant to control the chemical form of tritium release. - Abstract: The accurate measurement of behavior of bred tritium released from a tritium breeder is indispensable to understand the behavior for a design of a tritium extraction system. The tritium collection method combined a CuO bed and water bubbles was not suitable to measure transient behavior of tritium released from Li{sub 2}TiO{sub 3} during neutron irradiation because tritium released behavior was changed to be delayed due to adsorption of oxidized tritium on the CuO. Hence, the tritium collection method with hydrophobic catalyst instead of the CuO was demonstrated and succeeded the accurate release measurement of tritium from Li{sub 2}TiO{sub 3}. With the method, we assessed the behavior of tritium release under the various conditions since tritium should be released from Li{sub 2}TiO{sub 3} as the form of HT as much as possible from the view point of the fuel cycle. Our results indicated; promotion of isotopic exchange reaction on the surface of Li{sub 2}TiO{sub 3} by addition of hydrogen in sweep gas is mandatory in order to release tritium smoothly from Li{sub 2}TiO{sub 3} irradiated with neutrons; the favorable sweep gas to release as the form of HT was hydrogen added inert gas; and the temperature of Li{sub 2}TiO{sub 3} was the dominant parameter to control the chemical form of tritium released from the Li{sub 2}TiO{sub 3}.

Development of advanced tritium breeding material with added lithium for ITER-TBM

Energy Technology Data Exchange (ETDEWEB)

Hoshino, Tsuyoshi, E-mail: hoshino.tsuyoshi@jaea.go.jp [Blanket Irradiation and Analysis Group, Fusion Research and Development Directorate, Japan Atomic Energy Agency, 4002, Narita-cho, Oarai-machi, Higashi Ibaraki-gun, Ibaraki 311-1393 (Japan); Kato, Kenichi; Natori, Yuri; Oikawa, Fumiaki; Nakano, Natsuko; Nakamura, Mutsumi [Kaken, Co. Ltd., 1044, Hori, Mito-city, Ibaraki 310-0903 (Japan); Sasaki, Kazuya [Institute of Engineering Innovation and Department of Nuclear Engineering and Management School of Engineering, University of Tokyo, 2-11-16 Yayoi, Bunkyo-ku, Tokyo 113-8656 (Japan); Suzuki, Akihiro [Nuclear Professional School, School of Engineering, University of Tokyo, 2-22 Shirakata-Shirane, Ibaraki 319-1188 (Japan); Terai, Takayuki [Institute of Engineering Innovation and Department of Nuclear Engineering and Management School of Engineering, University of Tokyo, 2-11-16 Yayoi, Bunkyo-ku, Tokyo 113-8656 (Japan); Tatenuma, Katsuyoshi [Kaken, Co. Ltd., 1044, Hori, Mito-city, Ibaraki 310-0903 (Japan)

2011-10-01

Lithium titanate (Li{sub 2}TiO{sub 3}) is one of the most promising candidates among tritium breeding materials because of its good tritium release characteristics. However, the mass of Li{sub 2}TiO{sub 3} decreased with time in a hydrogen atmosphere by the reduction of Ti and Li evaporation. In order to prevent the mass decrease at high temperatures, advanced tritium breeding material with added Li (Li{sub 2+x}TiO{sub 3+y}) should be developed. For this purpose, an advanced Li{sub 2}TiO{sub 3} with added Li was synthesized from proportionally mixed LiOH.H{sub 2}O and H{sub 2}TiO{sub 3} with a Li/Ti ratio of 2.2. The results of X-ray diffraction measurement showed that this advanced tritium breeding material existed as the non-stoichiometric compound Li{sub 2+x}TiO{sub 3+y}. The desired molar ratio of Li/Ti was achieved by appropriate mixing of LiOH.H{sub 2}O and H{sub 2}TiO{sub 3}. Therefore, synthesis by mixing LiOH.H{sub 2}O and H{sub 2}TiO{sub 3} is a promising mass production method for the advanced tritium breeding material with added Li for the test blanket module of ITER.

Safety and environmental advantages of using tritium-lean targets for inertial fusion

International Nuclear Information System (INIS)

Arzeni, S.; Latkowski, J. F.; Logan, B. G.; Meier, W. R.; Moir, R. W.; Perkins, L. J.; Sanz, J.

1999-01-01

While traditional inertial fusion energy target designs typically use equimolar portions of deuterium and tritium and have areal densities (ρr) of ∼ 3 g/cm 2 , significant safety and environmental (S and E) advantages may be obtained through the use of high-density (ρr ∼ 10 g/cm 2 ) targets with tritium components as low as 0.5%. Such targets would absorb much of the neutron energy within the target and could be self-sufficient from a tritium breeding point of view. Tritium self-sufficiency within the target would free target chamber designers from the need to use lithium-bearing blanket materials, while low inventories within each target would translate into low inventories in target fabrication facilities. Absorption of much of the neutron energy within the target, the extremely low tritium inventories, and the greatly moderated neutron spectrum, make ''tritium-lean'' targets appear quite attractive from an S and E perspective

Ceramics for fusion reactors: The role of the lithium orthosilicate as breeder

Energy Technology Data Exchange (ETDEWEB)

Carella, Elisabetta, E-mail: elisabetta.carella@ciemat.es [National Laboratory for Magnetic Fusion, CIEMAT, Madrid (Spain); Hernandez, Teresa [National Laboratory for Magnetic Fusion, CIEMAT, Madrid (Spain)

2012-11-15

Lithium-based oxide ceramics are studied as breeder blanket materials for the controlled thermonuclear reactors (CTR). Lithium orthosilicate (Li{sub 4}SiO{sub 4}) is one of the most promising candidates because of its lithium concentration (0.54 g/cm{sup 3}), its high melting temperature (1523 K) and its excellent tritium release behavior. It is reported that the diffusion of tritium is closely related to that of lithium, so it is possible to find an indirect measure of the trend of tritium studying the diffusivity of Li{sup +}. In the present work, the synthesis of the Li{sub 4}SiO{sub 4} is carried out by Spray drying followed by pyrolysis. The study of the Li{sup +} ion diffusion on the sintered bodies, is investigated by means of electrical conductivity measurements. The effect of the {gamma}-ray irradiation is evaluated by the impedance spectroscopy method (EIS) from room temperature to 1173 K. The results indicate that the sintesis process employed can produce Li{sub 4}SiO{sub 4} in the form of pebbles, finally the best ion species for the electrical conduction is the Li{sup +} and is shown that the g-irradiation to a dose of 5MGy, facilitate its mobility through the creation of defects, without change in its conduction process.

Isothermal release of tritium from neutron-irradiated Li/sub 2/O pellets

Energy Technology Data Exchange (ETDEWEB)

O' Hira, Shigeru; Nagao, Hiroshi; Fujii, Yasuhiko; Okamoto, Makoto

1986-04-01

Li/sub 2/O pellets irradiated with thermal neutrons were isothermally annealed to release tritium in a helium atmosphere at temperatures ranging from 673 to 1073 K. The release rates were found to significantly increase at elevated temperatures and to depend on the density of the Li/sub 2/O pellet. The overall diffusion coefficients of the release process were calculated using the cylindrical geometry model for the pellets as D(cm/sup 2/ s/sup -1/)=1.02 x 10/sup -3/ exp(-51.0 kJ mol/sup -1//RT)(90% theoretical density pellets), and D (cm/sup 2/ s/sup -1/)=2.64 x 10/sup -3/ exp(-46.5 kJ mol/sup -1//RT)(ca. 80% T.D. pellets) over the region 773 <= T <= 1073/sup 0/K. The result of the release experiment at 673/sup 0/K sugested that the diffusion rate was controlled by the decomposition of lithium hydroxide on the surface of Li/sub 2/O grains.

New radiobiological findings bearing on the 1977 ICRP recommendations. [Sensitivity of mouse and monkey prenatal oocytes to chronic, low-dose, tritium exposure

Energy Technology Data Exchange (ETDEWEB)

Dobson, R.L.

1979-02-14

Recent experiments on low-level irradiation during development raise questions relevant to ICRP Publication 26. Mice and monkeys were studied; the measured endpoint was the radiation-induced loss of female germ cells. Three issues are examined. The first is the numerical value of Q (quality factor) appropriate for low-energy beta rays. Comparisons of tritium with gamma radiation were made under conditions of chronic, low-level exposure, and the relative biological effectiveness (RBE) was found to approach 3. Its bearing on ICRP's recommendations concerning Q applicable to tritium is discussed. Second, female germ cells in squirrel monkeys before birth were discovered to be extraordinarily radiosensitive, more easily destroyed than those of mice. If this holds for other primates too, it has radiation-protection implications hitherto overlooked. Third, the contrast between massive germ-cell loss from chronic exposure in prenatal squirrel monkeys and reported radioresistance of oocytes to acute exposure in rhesus monkeys, unless due to species difference, suggests that during development protracted irradiation may be especially injurious. This also could have important radiation-protection implications and is under investigation. (ERB)

Fluorine 18 in tritium generator ceramic materials

International Nuclear Information System (INIS)

Jimenez-Becerril, J.; Bosch, P.; Bulbulian, S.

1992-01-01

At present time, the ceramic materials generators of tritium are very interesting mainly by the necessity of to found an adequate product for its application as fusion reactor shielding. The important element that must contain the ceramic material is the lithium and especially the isotope with mass=6. The tritium in these materials is generated by neutron irradiation, however, when the ceramic material contains oxygen, then is generated too fluorine 18 by the action of energetic atoms of tritium in recoil on the 16 O, as it is showed in the next reactions: 1) 6 Li (n, α) 3 H ; 2) 16 O( 3 H, n) 18 F . In the present work was studied the LiAlO 2 and the Li 2 O. The first was prepared in the laboratory and the second was used such as it is commercially expended. In particular the interest of this work is to study the chemical behavior of fluorine-18, since if it would be mixed with tritium it could be contaminate the fusion reactor fuel. The ceramic materials were irradiated with neutrons and also the chemical form of fluorine-18 produced was studied. It was determined the amount of fluorine-18 liberated by the irradiated materials when they were submitted to extraction with helium currents and argon-hydrogen mixtures and also it was investigated the possibility about the fluorine-18 was volatilized then it was mixed so with the tritium. Finally it was founded that the liberated amount of fluorine-18 depends widely of the experimental conditions, such as the temperature and the hydrogen amount in the mixture of dragging gas. (Author)

Influence of additives and impurities in sweep gas and solid tritium release behaviour from lithium ceramics (review)

International Nuclear Information System (INIS)

Tanaka, Satoru

1991-01-01

Tritium release from solid breeding material is affected by small amounts of additives or impurities in the sweep gas or solid itself. Addition of hydrogen or water vapor to the sweep gas is reported to enhance the surface reaction of tritium release. Doping to solid breeder with elements of different valence from lithium has a possibility to improve tritium diffusion in the solid. Surface reaction and migration behavior in bulk are believed to be also affected by impurities in the sweep gas and in the solid. In order to model tritium release behavior in the blanket of fusion reactor, the mechanism of interaction with these additives or impurities must be quantitatively formulated. However, the mechanism of these remains to be elucidated. In this paper effects of these additives and impurities on tritium migration are reviewed. The mechanism of surface reaction for He+H 2 sweep gas is also discussed. (orig.)

Tritium release and retention properties of highly neutron-irradiated beryllium pebbles from HIDOBE-01 experiment

Energy Technology Data Exchange (ETDEWEB)

Chakin, V., E-mail: vladimir.chakin@kit.edu [Karlsruhe Institute of Technology, Institute for Applied Materials, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen (Germany); Rolli, R.; Moeslang, A.; Klimenkov, M.; Kolb, M.; Vladimirov, P.; Kurinskiy, P.; Schneider, H.-C. [Karlsruhe Institute of Technology, Institute for Applied Materials, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen (Germany); Til, S. van; Magielsen, A.J. [Nuclear Research and Consultancy Group, Westerduinweg 3, Postbus 25, 1755 ZG Petten (Netherlands); Zmitko, M. [The European Joint Undertaking for ITER and the Development of Fusion Energy, c/Josep Pla, no. 2, Torres Diagonal Litoral, Edificio B3, 08019 Barcelona (Spain)

2013-11-15

The current helium cooled pebble bed (HCPB) tritium breeding blanket concept for fusion reactors includes a bed of 1 mm diameter beryllium pebbles to act as a neutron multiplier. Beryllium pebbles, fabricated by the rotating electrode method, were neutron irradiated in the HFR in Petten within the HIDOBE-01 experiment. This study presents tritium release and retention properties and data on microstructure evolution of beryllium pebbles irradiated at 630, 740, 873, 948 K up to a damage dose of 18 dpa, corresponding to a helium accumulation of about 3000 appm. The measured cumulative released activity from the beryllium pebbles irradiated at 948 K was found to be significantly lower than the calculated value. After irradiation at 873 and 948 K scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analyses revealed large pores or bubbles in the bulk and oxide films with a thickness of up to 8 μm at the surface of the beryllium pebbles. The radiation-enhanced diffusion of tritium and the formation of open porosity networks accelerate the tritium release from the beryllium pebbles during the high-flux neutron irradiation.

Conclusions drawn of tritium balance in light water reactors

International Nuclear Information System (INIS)

Dolle, L.; Bazin, J.

1978-01-01

In the tritium balance of pressurized water reactors, using boric acid and lithium in the cooling water, contribution of the tritium produced by fission, diffusing through the zircalloy of the fuel cladding estimated to 0.1%, was not in agreement with quantities measured in reactors. It is still difficult to estimate what percentage is represented by the tritium formed by fission in the fuel, owing to diffusion through cladding. The tritium balance in different working nuclear power stations is consequently of interest. The tritium balance method in the water of the cooling circuit of PWR is fast and experimentally simple. It is less sensitive to errors originating from fission yields than balance of tritium produced by fission in the fuel. A tritium balance in the water of the cooling circuit of Biblis-A, with a specific burn-up of 18000 MWd/t gives a better precision. Diffusion rate of tritium produced by fission was less than 0.2%. So low a contribution is a justification to the use of lithium with an isotopic purity of 99.9% of lithium 7 to limit at a low value the residual lithium 6 [fr

Modeling of tritium behavior in Li2O

International Nuclear Information System (INIS)

Billone, M.C.; Attaya, H.; Kopasz, J.P.

1992-08-01

The TIARA and DISPL2 codes are being developed at Argonne National Laboratory to predict tritium retention and release from lithium ceramics under steady-state and transient conditions, respectively. Tritium retention and release are important design and safety issues for tritium-breeding blankets of fusion reactors. Emphasis has been placed on tritium behavior in Li 2 O because of the selection of this ceramic as a first option for the ITER driver blanket and because of the relatively good material properties data base for Li 2 O. Models and correlations for diffusion, surface desorption/adsorption, and solubility/precipitation of tritium in Li 2 0 have been developed based on well-controlled laboratory data from as-fabricated and irradiated samples. With the models and correlations, the codes are validated to the results of in-reactor purge flow tests. The results of validation of TIARA to tritium retention data from VOM-15H, EXOTIC-2, and CRITIC-1 are presented, along with predictions of tritium retention in BEATRIX-II. For DISPL2, results are presented for tritium release predictions vs. data for MOZART, CRITIC-1, and BEATRIX-II. Recommendations are made for improving both the data base and the modeling to allow extrapolation with reasonable uncertainty levels to fusion reactor design conditions

Parameters governing tritium extraction rates from lithiated ceramics. The case of lithium aluminate

International Nuclear Information System (INIS)

Roth, E.; Botter, F.; Briec, M.; Rasneur, B.; Roux, N.

1986-10-01

Significant discrepancies between results of authors comparing tritium extraction rates from different lithiated ceramics are found in the literature. Recent results obtained at C.E.A., principally on lithium aluminates, show that, for a given ceramic, parameters other than textural (grain size, porosity, etc...) may play a predominant role. Enhancements of extraction rates have been induced by adding MgO to the solid or H 2 and CO to the sweep gas, but other factors, probably related to the surface condition of samples, may produce even greater effects. Results of investigations of the influence of exposure to air at given partial pressures of water vapor or of CO 2 show that strict preirradiation procedures must be adopted for preparation, storage and handling of ceramic tritium breeders

Properties of tritium and its compounds

International Nuclear Information System (INIS)

Belovodskij, L.F.; Gaevoj, V.K.; Grishmanovskij, V.I.

1985-01-01

Ways of tritium preparation and different aspects of its application are considered. Physicochemical properties of this isotope and some compounds of it - tritium oxides, lithium, titanium, zirconium, uranium tritides, tritium organic compounds - are discussed. In particular, diffusion of tritium and its oxide through different materials, tritium oxidation processes, decomposition of tritium-containing compounds under the action of self-radiation are considered. Main radiobiological tritium properties are described

Material modifications in lithium niobate and lithium tantalate crystals by ion irradiation

International Nuclear Information System (INIS)

Raeth, Niels Lennart

2017-01-01

The artificially produced crystals lithium niobate (LiNbO 3 ) and the closely related lithium tantalate (LiTaO 3 ) are proven starting materials for producing active and passive devices that can guide, amplify, switch and process light. For this purpose, it is often necessary to be able to influence the refractive index of the substrate targeted, which is possible in addition to other methods by irradiation of the materials with fast light ions. In this work, lithium niobate and lithium tantalate crystals are irradiated with alpha particles, 3 He ions, deuterons, and protons at projectile energies of up to 14 MeV / nucleon. Energy and crystal thickness are chosen so that the projectiles penetrate the entire sample and are not implanted. All isotopes responsible for the unwanted nuclear activation of the crystals due to the irradiation are relatively short-lived and overall the activation decreases fast enough to allow the safe handling of the irradiated samples after a storage period of a few days to a few weeks. The refractive index changes produced in lithium niobate and lithium tantalate by irradiation with the different projectiles are determined interferometrically and can also be measured by suitable choice of the sample geometry as a function of the ion penetration depth: In LiNbO 3 the ordinary refractive index decreases, the extraordinary increases equally. In LiTaO 3 , both the ordinary and the extraordinary refractive indices decrease as a result of the irradiation; the ordinary refractive index change is many times stronger than the extraordinary one. There is an enormous long-term stability at room temperature for both crystal systems: Even after eleven (LiNbO 3 ) or three (LiTaO 3 ) years, no decrease in the ion beam-induced refractive index change can be observed. The ion beam-induced refractive index changes are probably the result of atomic displacements such as vacancies, defect clusters or ''latent tracks''. An explanation for

Breeding blanket development. Tritium release from breeder

International Nuclear Information System (INIS)

Tsuchiya, Kunihiko; Kawamura, Hiroshi; Nagao, Yoshiharu

2006-01-01

Engineering data on neutron irradiation performance of tritium breeders are needed to design the breeding blanket of fusion reactor. In this study, tritium release experiments of the breeders were carried out to examine the effects of various parameters (such as sweep gas flow rate, hydrogen content in sweep gas, irradiation temperature and thermal neutron flux) on tritium generation and release behavior. Lithium titanate (Li 2 TiO 3 ) is considered as a candidate tritium breeder in the blanket design of International Thermonuclear Experimental Reactor (ITER). As for the shape of the breeder material, a small spherical form is preferred to reduce the thermal stress induced in the breeder. Li 2 TiO 3 pebbles of about 170g in total weight and with 0.3 and 2 mm in diameter were manufactured by a wet process, and an assembly packed with the binary Li 2 TiO 3 pebbles was irradiated in Japan Materials Testing Reactor (JMTR). The tritium was generated in the Li 2 TiO 3 pebble bed and released from the pebble bed, and was swept downstream using the sweep gas for on-line analysis of tritium content. Concentration of total tritium and gaseous tritium (HT or T 2 gas) released from the Li 2 TiO 3 pebble bed were measured by ionization chambers, and the ratio of (gaseous tritium)/(total tritium) was evaluated. The sweep gas flow rate was changed from 100 to 900cm 3 /min, and hydrogen content in the sweep gas was changed from 100 to 10000 ppm. Furthermore, thermal neutron flux was changed using a window made of hafnium (Hf) neutron absorber. The irradiation temperature at an outer region of the Li 2 TiO 3 pebble bed was held between 200 and 400degC. The main results of this experiment are summarized as follows. 1) When the temperature at the outside edge of the Li 2 TiO 3 pebble bed exceeded 100degC, the tritium release from the Li 2 TiO 3 pebble bed started. The ratio of the tritium release rate and the tritium generation rate (normalized tritium release rate: R/G) reached

Industrial routes for lithium zirconate elements

International Nuclear Information System (INIS)

Bastide, B.; Roux, N.

1991-01-01

Lithium metazirconate Li 2 ZrO 3 is one of the leading ceramics contemplated in solid blanket concepts. Among its merits are fair physical properties, satisfactory compatibility with structural materials and beryllium, satisfactory mechanical strength, excellent irradiation behavior as shown by a comparative irradiation of ceramics in EBR 2 reactor, and very good tritium release performance as evidence in the MOZART, and EXOTIC neutron irradiation. Pechiney and the CEA are jointly involved in developing industrial fabrication of Li 2 ZrO 3 elements to the microstructural, geometrical (pellets, rings, spheres) specifications required for their use in solid blanket conceived in the European Program

Influence of chemisorption products of carbon dioxide and water vapour on radiolysis of tritium breeder

Energy Technology Data Exchange (ETDEWEB)

Zarins, Arturs, E-mail: arturs.zarins@lu.lv [University of Latvia, Institute of Chemical Physics, Kronvalda Boulevard 4, LV-1010 Riga (Latvia); Kizane, Gunta; Supe, Arnis [University of Latvia, Institute of Chemical Physics, Kronvalda Boulevard 4, LV-1010 Riga (Latvia); Knitter, Regina; Kolb, Matthias H.H. [Karlsruhe Institute of Technology, Institute for Applied Materials (IAM-WPT), 76021 Karlsruhe (Germany); Tiliks, Juris; Baumane, Larisa [University of Latvia, Institute of Chemical Physics, Kronvalda Boulevard 4, LV-1010 Riga (Latvia)

2014-10-15

Highlights: • Chemisorption products affect formation proceses of radiation-induced defects. • Radiolysis of chemisorption products increase amount of radiation-induced defects. • Irradiation atmosphere influence radiolysis of lithium orthosilicate pebbles. - Abstract: Lithium orthosilicate pebbles with 2.5 wt% excess of silica are the reference tritium breeding material for the European solid breeder test blanket modules. On the surface of the pebbles chemisorption products of carbon dioxide and water vapour (lithium carbonate and hydroxide) may accumulate during the fabrication process. In this study the influence of the chemisorption products on radiolysis of the pebbles was investigated. Using nanosized lithium orthosilicate powders, factors, which can influence the formation and radiolysis of the chemisorption products, were determined and described as well. The formation of radiation-induced defects and radiolysis products was studied with electron spin resonance and the method of chemical scavengers. It was found that the radiolysis of the chemisorption products on the surface of the pebbles can increase the concentration of radiation-induced defects and so could affect the tritium diffusion, retention and the released species.

Tritium adsorption/release behaviour of advanced EU breeder pebbles

Science.gov (United States)

Kolb, Matthias H. H.; Rolli, Rolf; Knitter, Regina

2017-06-01

The tritium loading of current grades of advanced ceramic breeder pebbles with three different lithium orthosilicate (LOS)/lithium metatitanate (LMT) compositions (20-30 mol% LMT in LOS) and pebbles of EU reference material, was performed in a consistent way. The temperature dependent release of the introduced tritium was subsequently investigated by temperature programmed desorption (TPD) experiments to gain insight into the desorption characteristics. The obtained TPD data was decomposed into individual release mechanisms according to well-established desorption kinetics. The analysis showed that the pebble composition of the tested samples does not severely change the release behaviour. Yet, an increased content of lithium metatitanate leads to additional desorption peaks at medium temperatures. The majority of tritium is released by high temperature release mechanisms of chemisorbed tritium, while the release of physisorbed tritium is marginal in comparison. The results allow valuable projections for the tritium release behaviour in a fusion blanket.

Stability of lithium niobate on irradiation at elevated temperature

International Nuclear Information System (INIS)

Primak, W.; Gavin, A.P.; Anderson, T.T.; Monahan, E.

1977-01-01

In contrast to results obtained for neutron irradiation in a thermal reactor near room temperature, lithium niobate plates irradiated in the Experimental Breeder Reactor II (EBR-II) did not become metamict. This is attributed to the elevated temperature of the EBR-II. Ion bombardment experiments indicate that to avoid disordering of lithium niobate on irradiation, its temperature should be maintained above 673 K. Evidence for ionic conductivity was found at 873 K, indicating that it would be inadvisable to permit the temperature to rise that high, particularly with voltage across the plate. In reactor application as a microphone transducer, it is tentatively recommended that the lithium niobate be maintained in the middle of this temperature range for a major portion of reactor operating time

Tritium resources available for fusion reactors

Science.gov (United States)

Kovari, M.; Coleman, M.; Cristescu, I.; Smith, R.

2018-02-01

The tritium required for ITER will be supplied from the CANDU production in Ontario, but while Ontario may be able to supply 8 kg for a DEMO fusion reactor in the mid-2050s, it will not be able to provide 10 kg at any realistic starting time. The tritium required to start DEMO will depend on advances in plasma fuelling efficiency, burnup fraction, and tritium processing technology. It is in theory possible to start up a fusion reactor with little or no tritium, but at an estimated cost of 2 billion per kilogram of tritium saved, it is not economically sensible. Some heavy water reactor tritium production scenarios with varying degrees of optimism are presented, with the assumption that only Canada, the Republic of Korea, and Romania make tritium available to the fusion community. Results for the tritium available for DEMO in 2055 range from zero to 30 kg. CANDU and similar heavy water reactors could in theory generate additional tritium in a number of ways: (a) adjuster rods containing lithium could be used, giving 0.13 kg per year per reactor; (b) a fuel bundle with a burnable absorber has been designed for CANDU reactors, which might be adapted for tritium production; (c) tritium production could be increased by 0.05 kg per year per reactor by doping the moderator with lithium-6. If a fusion reactor is started up around 2055, governments in Canada, Argentina, China, India, South Korea and Romania will have the opportunity in the years leading up to that to take appropriate steps: (a) build, refurbish or upgrade tritium extraction facilities; (b) extend the lives of heavy water reactors, or build new ones; (c) reduce tritium sales; (d) boost tritium production in the remaining heavy water reactors. All of the alternative production methods considered have serious economic and regulatory drawbacks, and the risk of diversion of tritium or lithium-6 would also be a major concern. There are likely to be serious problems with supplying tritium for future

Tritium adsorption/release behaviour of advanced EU breeder pebbles

Energy Technology Data Exchange (ETDEWEB)

Kolb, Matthias H.H., E-mail: matthias.kolb@kit.edu; Rolli, Rolf; Knitter, Regina

2017-06-15

The tritium loading of current grades of advanced ceramic breeder pebbles with three different lithium orthosilicate (LOS)/lithium metatitanate (LMT) compositions (20–30 mol% LMT in LOS) and pebbles of EU reference material, was performed in a consistent way. The temperature dependent release of the introduced tritium was subsequently investigated by temperature programmed desorption (TPD) experiments to gain insight into the desorption characteristics. The obtained TPD data was decomposed into individual release mechanisms according to well-established desorption kinetics. The analysis showed that the pebble composition of the tested samples does not severely change the release behaviour. Yet, an increased content of lithium metatitanate leads to additional desorption peaks at medium temperatures. The majority of tritium is released by high temperature release mechanisms of chemisorbed tritium, while the release of physisorbed tritium is marginal in comparison. The results allow valuable projections for the tritium release behaviour in a fusion blanket.

Overview of the TFTR Lithium Blanket Module program

International Nuclear Information System (INIS)

Jassby, D.L.

1986-01-01

The LBM (Lithium Blanket Module) is an approximately cubic module, about 80 cm on each side, with construction representative of a helium-cooled lithium oxide fusion reactor blanket module. Measurements of neutron transport and tritium breeding in the LBM will be made in irradiation programs first with a point-neutron source, and subsequently with the D-D and D-T fusion-neutron sources of the TFTR. This paper summarizes the objectives of the LBM program, the design, development and construction of the LBM, and progress in the experimental tests

Irradiaiton facilities for testing solid and liquid blanket breeder materials with in-situ tritium release measurements in the HFR Petten

International Nuclear Information System (INIS)

Conrad, R.; Debarberis, L.

1991-01-01

Lithium-based tritium breeder materials for solid and liquid fusion reactor blanket concepts are being tested in the High Flux Reactor (HFR) Petten with in-situ tritium release measurements since 1985, within the European Fusion Technology Programme and the BEATRIX-I programme. Ceramic breeder materials are being tested in the EXOTIC and COMPLIMENT experimental programmes and the liquid breeder material, Pb-17Li, is being tested in the LIBRETTO experimental programme. The in-pile experiments are performed with irradiation facilities developed by the Joint Research Centre (JRC) Petten. The irradiation vehicles are multi-channel rigs. The sample holders consist of independent, fully instrumented and triple contained capsules. The out-of-pile experimental equipment consist of twelve independent circuits for on-line tritium release and tritium permeation measurements and eight independent circuits for temperature control. The experimental achievements obtained so far contribute to the selection of candidate tritium breeder materials for blanket concepts of near future machines like NET, ITER and DEMO. (orig.)

Study of damages by neutron irradiation in lithium aluminates; Estudio de danos por irradiacion neutronica en aluminatos de litio

Energy Technology Data Exchange (ETDEWEB)

Palacios G, O

1999-06-01

Lithium aluminates proposed to the production of tritium in fusion nuclear reactors, due to the thermal stability that they present as well as the behavior of the aluminium to the irradiation. As a neutron flux with profile ({approx_equal} 14 Mev) of a fusion reactor is not available. A irradiation experiment was designed in order to know the micro and nano structure damages produced by fast and thermal neutrons in two irradiation positions of the fusion nuclear reactor Triga Mark III: CT (Thermal Column) and SIFCA (System of Irradiation Fixed of Capsules). In this work samples of lithium aluminate were characterized by XRD (X-Ray Diffraction), TEM (Transmission Electron Microscopy) and SEM (Scanning Electron Microscopy). Two samples were prepared by two methods: a) coalition method and b) peroxide method. This characterization comprised original and irradiated samples. The irradiated sample amounted to 4 in total: one for each preparation method and one for each irradiation position. The object of this analysis was to correlate with the received neutron dose the damages suffered by the samples with the neutron irradiation during long periods (440 H), in their micro and nano structure aspects; in order to understand the changes as a function of the irradiation zone (with thermal and fast neutron flux) and the preparation methods of the samples and having as an antecedent the irradiation in SIFCA position by short times (2h). The obtained results are referred to the stability of {gamma} -aluminate phase, under given conditions of irradiation and defined nano structure arrangement. They also refer to the proposals of growth mechanism and nucleation of new phases. The error associated with the measurement of neutron dose is also discussed. (Author)

Comparison of shear bond strength of self-etch and self-adhesive cements bonded to lithium disilicate, enamel and dentin.

Science.gov (United States)

Naranjo, Jennifer; Ali, Mohsin; Belles, Donald

2015-11-01

Comparison of shear bond strength of self-etch and self-adhesive cements bonded to lithium disilicate, enamel and dentin. With several self-adhesive resin cements currently available, there is confusion about which product and technique is optimal for bonding ceramic restorations to teeth. The objective of this study was to compare the shear bond strength of lithium disilicate cemented to enamel and dentin using 5 adhesive cements. 100 lithium disilicate rods were pretreated with 5% hydrofluoric acid, silane, and cemented to 50 enamel and 50 dentin surfaces using five test cements: Variolink II (etch-and-rinse) control group, Clearfil Esthetic (two step self-etch), RelyX Unicem, SpeedCEM, and BifixSE (self-adhesive). All specimens were stored (37 degrees C, 100% humidity) for 24 hours before testing their shear bond strength using a universal testing machine (Instron). Debonded surfaces were observed under a low-power microscope to assess the location and type of failure. The highest bond strength for both enamel and dentin were recorded for Variolink II, 15.1MPa and 20.4MPa respectively, and the lowest were recorded for BifixSE, 0.6MPa and 0.9MPa respectively. Generally, higher bond strengths were found for dentin (7.4MPa) than enamel (5.3MPa). Tukey's post hoc test showed no significant difference between Clearfil Esthetic and SpeedCem (p = 0.059), Unicem and SpeedCem (p = 0.88), and Unicem and BifixSE (p = 0.092). All cements bonded better to lithium disilicate than to enamel or dentin, as all bond failures occurred at the tooth/adhesive interface except for Variolink II. Bond strengths recorded for self-adhesive cements were very low compared to the control "etch and rinse" and self-etch systems. Further improvements are apparently needed in self-adhesive cements for them to replace multistep adhesive systems. The use of conventional etch and rinse cements such as Veriolink II should be preferred for cementing all ceramic restorations over self-adhesive cements

Module of lithium divertor for KTM tokamak

Energy Technology Data Exchange (ETDEWEB)

Lyublinski, I., E-mail: yublinski@yandex.ru [FSUE ' Red Star' , Moscow (Russian Federation); Vertkov, A.; Evtikhin, V.; Balakirev, V.; Ionov, D.; Zharkov, M. [FSUE ' Red Star' , Moscow (Russian Federation); Tazhibayeva, I. [IAE NNC RK, Kurchatov (Kazakhstan); Mirnov, S. [TRINITI, Troitsk, Moscow Region (Russian Federation); Khomiakov, S.; Mitin, D. [OJSC Dollezhal Institute, Moscow (Russian Federation); Mazzitelli, G. [ENEA RC Frascati (Italy); Agostini, P. [ENEA RC Brasimone (Italy)

2012-10-15

Highlights: Black-Right-Pointing-Pointer Problems of PFE degradation, tritium accumulation and plasma pollution can be overcome by the use of liquid lithium-metal with low Z. Black-Right-Pointing-Pointer Capillary-porous system (CPS) - new material in which liquid lithium fill a solid matrix from porous material. Black-Right-Pointing-Pointer Lithium divertor module for KTM tokamak is under development. Black-Right-Pointing-Pointer Lithium filled tungsten felt is offered as the base plasma facing material of divertor. Black-Right-Pointing-Pointer Results of this project addresses to the progress in the field of fusion neutrons source and fusion energy source creation. - Abstract: Activity on projects of ITER and DEMO reactors has shown that solution of problems of divertor target plates and other plasma facing elements (PFEs) based on the solid plasma facing materials cause serious difficulties. Problems of PFE degradation, tritium accumulation and plasma pollution can be overcome by the use of liquid lithium-metal with low Z. Application of lithium will allow to create a self-renewal and MHD stable liquid metal surface of the in-vessel devices possessing practically unlimited service life; to reduce power flux due to intensive re-irradiation on lithium atoms in plasma periphery that will essentially facilitate a problem of heat removal from PFE; to reduce Z{sub eff} of plasma to minimally possible level close to 1; to exclude tritium accumulation, that is provided with absence of dust products and an opportunity of the active control of the tritium contents in liquid lithium. Realization of these advantages is based on use of so-called lithium capillary-porous system (CPS) - new material in which liquid lithium fill a solid matrix from porous material. The progress in development of lithium technology and also activity in lithium experiments in the tokamaks TFTR, T-11M, T-10, FTU, NSTX, HT-7 and stellarator TJ II permits of solving the problems in development of

The behaviour of ceramic breeder materials with respect to tritium release and pellet/pebble mechanical integrity

Science.gov (United States)

Kwast, H.; Conrad, R.; May, R.; Casadio, S.; Roux, N.; Werle, H.

1994-09-01

In situ tritium release experiments from several candidate fusion blanket ceramic breeder materials have been performed in the High Flux Reactor (HFR) at Petten over the last few years. The sixth experiment, EXOTIC-6, contained pellets of LiAlO 2, Li 2XrO 3, Li 6Xr 2O 7 and Li 8ZrO 6 and pebbles of Li 4SiO 4 and Li 2ZrO 3 which were irradiated up to a lithium burnup of 3%. A large number of temperature transients and purge gas composition changes were performed. From the temperature transients tritium residence times have been determined. Some preliminary results were presented at the 17th Symposium on Fusion Technology (SOFT) held in Rome in 1992. In the present paper results of a further analysis of the residence times are presented together with some postirradiation examination results. The LiAlO 2 pellets showed a better mechanical stability than the Li-zirconates pellets. The pebbels remained intact. The tritium residence times determined from the tritium inventories were in good agreement with those previously determined from temperature transients. The tritium release characteristics of the materials investigated remain substantially unchanged up to the maximum lithium burnup achieved in this experiment.

Reactions of recoil tritium generated by the 3He(n,p)3H reaction with aromatic compounds -intramolecular tritium distribution and radiochemical yield

International Nuclear Information System (INIS)

Nogawa, N.; Morikawa, Naotake; Oohashi, Kunio; Matuoka, H.; Moki, T.; Moriya, T.

1986-01-01

Reactions of recoil tritium with benzoic acid, acetanilide and β-phenethyl alcohol were studied using the 3 He(=n,p) 3 H reaction. The tritium distribution in the aromatic ring is approximately uniform in all the irradiated compounds and the tritium activity per C-H bond in the methyl and ethylene groups is 7 to 8 relative to that of the corresponding ring as standard. These findings are substantially the same as those obtained previously by the 6 Li(n,α) 3 H reactions, suggesting the same mechanism of tritiation for both recoil reactions. The tritiated parent compounds were obtained in high radiochemical yields: 45% for benzoic acid, 30% for acetanilide, 12% for β-phenethyl alcohol. (author)

Liquid lithium blanket processing studies

International Nuclear Information System (INIS)

Talbot, J.B.; Clinton, S.D.

1979-01-01

The sorption of tritium on yttrium from flowing molten lithium and the subsequent release of tritium from yttrium for regeneration of the metal sorbent were investigated to evaluate the feasibility of such a tritium-recovery process for a fusion reactor blanket of liquid lithium. In initial experiments with the forced convection loop, yttrium samples were contacted with lithium at 300 0 C. A mass transfer coefficient of 2.5 x 10 - cm/sec, which is more than an order of magnitude less than the value measured in earlier static experiments, was determined for the flowing lithium system. Rates of tritium release from yttrium samples were measured to evaluate possible thermal regeneration of the sorbent. Values for diffusion coefficients at 505, 800, and 900 0 C were estimated to be 1.1 x 10 -13 , 4.9 x 10 -12 , and 9.3 x 10 -10 cm 2 /sec, respectively. Tritium release from yttrium was investigated at higher temperatures and with hydrogen added to the argon sweep gas to provide a reducing atmosphere

Benchmarking lithium amide versus amine bonding by charge density and energy decomposition analysis arguments.

Science.gov (United States)

Engelhardt, Felix; Maaß, Christian; Andrada, Diego M; Herbst-Irmer, Regine; Stalke, Dietmar

2018-03-28

Lithium amides are versatile C-H metallation reagents with vast industrial demand because of their high basicity combined with their weak nucleophilicity, and they are applied in kilotons worldwide annually. The nuclearity of lithium amides, however, modifies and steers reactivity, region- and stereo-selectivity and product diversification in organic syntheses. In this regard, it is vital to understand Li-N bonding as it causes the aggregation of lithium amides to form cubes or ladders from the polar Li-N covalent metal amide bond along the ring stacking and laddering principle. Deaggregation, however, is more governed by the Li←N donor bond to form amine adducts. The geometry of the solid state structures already suggests that there is σ- and π-contribution to the covalent bond. To quantify the mutual influence, we investigated [{(Me 2 NCH 2 ) 2 (C 4 H 2 N)}Li] 2 ( 1 ) by means of experimental charge density calculations based on the quantum theory of atoms in molecules (QTAIM) and DFT calculations using energy decomposition analysis (EDA). This new approach allows for the grading of electrostatic Li + N - , covalent Li-N and donating Li←N bonding, and provides a way to modify traditional widely-used heuristic concepts such as the -I and +I inductive effects. The electron density ρ ( r ) and its second derivative, the Laplacian ∇ 2 ρ ( r ), mirror the various types of bonding. Most remarkably, from the topological descriptors, there is no clear separation of the lithium amide bonds from the lithium amine donor bonds. The computed natural partial charges for lithium are only +0.58, indicating an optimal density supply from the four nitrogen atoms, while the Wiberg bond orders of about 0.14 au suggest very weak bonding. The interaction energy between the two pincer molecules, (C 4 H 2 N) 2 2- , with the Li 2 2+ moiety is very strong ( ca. -628 kcal mol -1 ), followed by the bond dissociation energy (-420.9 kcal mol -1 ). Partitioning the interaction energy

Experimental investigation on tritium release from lithium titanate pebble under high temperature of 1073 K

Energy Technology Data Exchange (ETDEWEB)

Ochiai, Kentaro, E-mail: howartre@onid.oregonstate.edu [Japan Atomic Energy Agency, Tokai-mura, Naka-gun, Ibaraki (Japan); Edao, Yuki; Kawamura, Yoshinori [Japan Atomic Energy Agency, Tokai-mura, Naka-gun, Ibaraki (Japan); Hoshino, Tsuyoshi [Japan Atomic Energy Agency, Rokkasho-mura, Kamikita-gun, Aomori (Japan); Ohta, Masayuki; Sato, Satoshi; Konno, Chikara [Japan Atomic Energy Agency, Tokai-mura, Naka-gun, Ibaraki (Japan)

2015-10-15

Highlights: • We have performed the tritium recovery experiment with the DT neutron source at 1073 K. • The tritium recovery corresponded with the calculated tritium production. • The chemical form of recovered tritium is affected by the temperature and kind of sweep gas. • The recovered HT increases at higher temperature and dry hydrogen circumstance. - Abstract: The temperature of Li{sub 2}TiO{sub 3} pebble breeder in a fusion DEMO blanket is assumed to be more than 1000 K. For the investigation of tritium release from a Li{sub 2}TiO{sub 3} pebble breeder blanket at such a high temperature, we have carried out a tritium release experiment with the DT neutron source at the JAEA-FNS. The Li{sub 2}TiO{sub 3} pebble (1.0–1.2 mm in diameter) of 70 g was put into a stainless steel container and installed into an assembly stratified with beryllium and Li{sub 2}TiO{sub 3} layers. During the DT neutron irradiation, the temperature was kept at 1073 K with wire heaters in the blanket container. Helium gas including 1% hydrogen gas (H{sub 2}/He) mainly flowed inside the container as the purge gas. Two chemical forms, HT and HTO, of extracted tritium were separately collected during the DT neutron irradiation by using water bubblers and CuO bed. The tritium activity in the water bubbler was measured by a liquid scintillation counter. To investigate the effect of moisture in the purge gas, we also performed the same experiments with H{sub 2}O/He gas (H{sub 2}O content: 1%) or pure helium gas. From our experiment at 1073 K, in the case of the purge gas includes H{sub 2}, it is indicated that the increasing tendency of HT release is similar to that of the dry H{sub 2}/He.

Swelling and outgassing of heavily-irradiated lithium hydride

International Nuclear Information System (INIS)

Souers, P.C.; Ackerman, F.J.; Biel, T.J.; Bigwood, J.; Brite, V.; Christensen, L.D.; Folkers, C.L.; Gede, V.; Griffith, C.M.; Huss, E.B.; Lindahl, R.; McCreary, T.; Otsuki, H.H.; Pond, R.L.; Snider, G.D.; Stanhope, C.; Stump, R.K.; Vanderhoofven, F.; Tsugawa, R.T.; Anderson, J.L.; Carstens, D.W.H.; Drumhiller, W.L.; Lewis, W.B.; Nasise, J.E.; Pretzel, F.E.; Szklarz, E.G.; Vier, D.T.; Bowman, R.C. Jr.; Attalla, A.

1988-01-01

Twenty-two years worth of data on lithium deuteride-tritide (Li(D, T)) from three national laboratories is presented. The percent linear swelling and the outgassing of hydrogen isotopes and 3 He for samples stored at 243 to 438 K are presented in summary tables. In some cases, up to a full half-life of tritium (12 years) has been spent in the study. Initial tritium concentrations range from 2 to 98 at%. The precision of the swelling is considered, and the evidence is ambiguous as to whether temperature cycling and handling affects swelling. The early outgassing is all hydrogen, but it turns to helium at long lines. The outgassing levels out for each sample but the amount outgassed varies wildly from sample to sample. At linear swellings beyond 11%, behavior becomes erratic. A maximum linear swelling of 23% is seen for one sample at 5000 days. (orig.)

Design and qualification of an on-line permeator for the recovery of tritium from lead-lithium eutectic breeding alloy

International Nuclear Information System (INIS)

Veredas, G.; Fradera, J.; Fernandez, I.; Batet, L.; Penalva, I.; Mesquida, L.; Abella, J.; Sempere, J.; Martinez, I.; Herrazti, B.; Sedano, L.

2011-01-01

The fast and efficient recovery of bred tritium represents a major milestone of tritium breeding technologies R and D and is key for the demonstration of fusion reactor fuel self-sufficiency. For lead-lithium eutectic, diverse technologies are currently being investigated and qualified. Permeator Against Vacuum (PAV) solution represents a firm candidate because: (i) runs as a single-step process for tritium on-line recovery, (ii) works passively allowing to be thermally governed, (iii) can be easily in-pipe integrated in Pb15.7Li loop systems and (iv) can be conceived with high compactness. An optimal design of a PAV requires a detailed hydraulic design optimization for established operational ranges. An optimal PAV design is proposed and qualified by numerical simulation.

The influence of irradiation defects on tritium release from Li{sub 2}O

Energy Technology Data Exchange (ETDEWEB)

Tanaka, Satoru; Grishmanov, V [Tokyo Univ. (Japan). Faculty of Engineering

1996-10-01

During reactor irradiation of Li{sub 2}O defects are introduced by neutrons, triton and helium ions produced by {sup 6}Li(n, {alpha}){sup 3}H reactions and {gamma}-rays. Simultaneous measurements of luminescence emission and tritium release were performed under various conditions (temperature, sweep gas chemical composition) for Li{sub 2}O single crystal and polycrystal in order to elucidate possible influence of defects on tritium release. (author)

Tritium release behavior from neutron-irradiated Li{sub 2}TiO{sub 3} single crystal

Energy Technology Data Exchange (ETDEWEB)

Tanifuji, Takaaki; Yamaki, Daiju; Noda, Kenji [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Nasu, Shoichi

1998-03-01

Li{sub 2}TiO{sub 3} single-crystals with various size (1-2mm) were used as specimens. After the irradiation up to 4 x 10{sup 18} n/cm{sup 2} with thermal neutrons in JRR-2, tritium release from the Li{sub 2}TiO{sub 3} specimens in isothermal heating tests was continuously measured with a proportional counter. The tritium release in the range from 625K to 1373K seems to be controlled by bulk diffusion. The tritium diffusion coefficient (D{sub T}) in Li{sub 2}TiO{sub 3} was evaluated to be D{sub T}(cm{sup 2}/sec) = 0.100exp(-104(kJ/mol)/RT), 625Ktritium diffusion coefficients in Li{sub 2}TiO{sub 3} is almost equal to those of Li{sub 2}O irradiated with thermal neutrons up to 2 x 10{sup 19} n/cm{sup 2}. It indicates that the tritium release performance of Li{sub 2}TiO{sub 3} is essentially good as Li{sub 2}O. (author)

Irradiation of lithium-based ceramics for fusion blanket application

International Nuclear Information System (INIS)

Hastings, I.J.; Miller, J.M.; Verrall, R.A.; Bokwa, S.R.; Rose, D.H.

1986-06-01

Unvented CREATE (Chalk River Experiment to Assess Tritium Emission) tests have shown that under reducing conditions, most of the tritium (greater than 70%) is released from LiAlO 2 and Li 2 O as HT or T 2 ; the balance as HTO or T 2 O. Residual tritium is very small, less than 0.02%. Varying the sweep gas composition has a dramatic effect on the form of tritium released. With a quartz extraction tube during post- irradiation heating, a He sweep gas results in 10-30% release as HT or T 2 ; with a He-1%H 2 sweep gas, greater than 60% release as HT is achieved. The effect of extraction tube material is also significant. Using pure He sweep gas, a quartz extraction tube results in 10-30% release as HT or T 2 ; stainless steel produces 80-95% as HT or T 2 . Chalk River and CEA (Saclay) - fabricated LiAlO 2 behaved similarly to that from ANL in these tests. The first vented test at Chalk River, CRITIC-I, planned for 1986/87, will examine ANL-fabricated Li 2 O, 0.3 wt% 6 Li, 30 mm ID, 40 mm OD annular pellets, in a six-month irradiation at 700-1200 K, varying the sweep gas, with on-line HT/HTO measurement

Lithium mass transport in ceramic breeder materials

International Nuclear Information System (INIS)

Blackburn, P.E.; Johnson, C.E.

1990-01-01

The objective of this activity is to measure the lithium vaporization from lithium oxide breeder material under differing temperature and moisture partial pressure conditions. Lithium ceramics are being investigated for use as tritium breeding materials. The lithium is readily converted to tritium after reacting with a neutron. With the addition of 1000 ppM H 2 to the He purge gas, the bred tritium is readily recovered from the blanket as HT and HTO above 400 degree C. Within the solid, tritium may also be found as LiOT which may transport lithium to cooler parts of the blanket. The pressure of LiOT(g), HTO(g), or T 2 O(g) above Li 2 O(s) is the same as that for reactions involving hydrogen. In our experiments we were limited to the use of hydrogen. The purpose of this work is to investigate the transport of LiOH(g) from the blanket material. 8 refs., 1 fig., 3 tabs

Synthesis of lithium silicates generators of tritium by a modified method of combustion

International Nuclear Information System (INIS)

Cruz G, D.

2003-01-01

The ceramics of lithium have been proposed as generating materials of tritium through the following reaction: 6 Li + 1 n → 4 He + 3 H . In previous works carried out by Pfeiffer and collaborators, the lithium silicates generators of tritium were prepared using the following methods: reactions of solid state, precipitation and sol-gel synthesis. Although those methods have advantages, it is required of heating at high temperatures (900 C during four hours) to be able to obtain the crystalline compounds. Those products found in these works were diverse crystallization forms of the lithium silicates and of SiO 2 , such as, Li 2 SiO 3 , Li 2 Si 2 0 5 , Li 4 SiO 4 , and quartz (SiO 2 ). The combustion method uses exothermic reactions to take place ceramic compounds. The precursor solutions are mixtures of the nitrate of metal oxidizer and the fuels (urea, glycine, carbohydrazide). However the reported method in the literature, it is not useful to prepare lithium silicates, for what was modified using non oxidizers compounds. The lithium hydroxide (LiOH) and the silicic acid (H 2 SiO 3 ) they were the compounds non oxidizers used, and the urea (CH 4 N 2 O) it was the one fuel. They were carried out two series of experiments; inside the series 1 of experiments are varied the molar ratio of lithium hydroxide and urea (LiOH : H 2 SiO 3 = 1, 2 and 3, LiOH : CH 4 N 2 O = 1, 2, 3, 4 and 5) and the prepared mixtures were taken to one muffle previously preheated to a temperature of 450 C during 5 minutes. In the series 2 of experiments was studied the effect of the temperature and of the washed with distilled water in the prepared samples with the following molar ratios: LiOH : H 2 SiO 3 : CH 4 N 2 O = 1:1:3, 2:1:3, 3:1:3 and 3:1:6, those which were heated to temperatures from 450 C up to 750 C and were washed. The obtained samples were characterized by X-ray diffraction (XRD), Infrared spectroscopy (I S), semiquantitative elemental analysis (EDS) and Thermal gravimetric

Recent progress in the modelling of helium and tritium behaviour in irradiated beryllium pebbles

International Nuclear Information System (INIS)

Rabaglino, E.; Ronchi, C.; Cardella, A.

2003-01-01

One of the key issues of the European Helium Cooled Pebble Bed blanket is the behaviour under irradiation of beryllium pebbles, which have the function of neutron multiplier. An intense production of helium occurs in-pile, as well as a non negligible generation of tritium. Helium bubbles induce swelling and a high tritium inventory is a safety issue. Extensive studies for a better understanding, characterisation and modelling of the behaviour of helium and tritium in irradiated beryllium pebbles are being carried out, with the final aim to enable a reliable prediction of gas release and swelling in the full range of operating and accidental conditions of a Fusion Power Reactor. The general strategy consists in integrating studies on macroscopic phenomena (gas release) with the characterisation of corresponding microscopic diffusion phenomena (bubble kinetics) and the assessment of some fundamental diffusion parameter for the models (gas atomic diffusion coefficients). The present work gives a summary of the latest achievements in this context. By an inverse analysis of experimental out-of-pile gas release from weakly irradiated pebbles, coupled to the study of the characteristics of bubble population, it has been possible to assess the thermal diffusion coefficients of helium and tritium in and to improve and validate the classical model of gas precipitation into bubbles inside the grain. The improvement of the description of gas atomic diffusion and precipitation is the first step to enable a more reliable prediction of gas release

Study of Paramagnetic Species in γ-irradiated Lithium Borate Glasses Doped With Cu2+ Ions

International Nuclear Information System (INIS)

Mansour, A.; Abd-Allah, W.M.; El-Alaily, N.A.; Ezz-Eldin, F.M.

2013-01-01

Mixed alkali borate glasses doped with different concentration of Cu O ranging from (0.1-10) wt% have been prepared by the melt quenching technique. The prepared samples were studied by means of density, molar volume, infrared spectroscopy and electron paramagnetic resonance (EPR) measurements before and after successive gamma irradiation (50-200 kGy). The results showed that the density increase while molar volume decrease with the increase of CuO %. The infrared absorption studies revealed that structure of the glass network consists of BO 3 , BO 4 and B-O-Cu linkages. Gamma irradiation causes minor changes in the IR spectral bands which are related to the bond break of the B-O bond and formation non-bridging oxygen. Gamma irradiation causes irregular change in the intensities of the EPR spectra for samples doped with 0.1, 0.2 and 10 wt % of Cu O, however, no change in the EPR spectra of 2 and 5 wt % of Cu O for all absorbed doses (50-200 kGy). It is expected that the Cu-doped lithium borate glass 2 and 5 wt % of Cu O may be used for radiation shielding.

Effect of Lithium Disilicate Reinforced Liner Treatment on Bond and Fracture Strengths of Bilayered Zirconia All-Ceramic Crown

Directory of Open Access Journals (Sweden)

Yong-Seok Jang

2018-01-01

Full Text Available This study was performed to evaluate the effect of a lithium-disilicate spray-liner application on both the bond strength between zirconia cores and heat-pressed lithium-disilicate glass-ceramic veneers, and the fracture strength of all-ceramic zirconia crowns. A lithium-disilicate reinforced liner was applied on the surface of a zirconia core and lithium-disilicate glass-ceramic was veneered on zirconia through heat press forming. Microtensile and crown fracture tests were conducted in order to evaluate, respectively, the bonding strength between the zirconia cores and heat pressed lithium-disilicate glass-ceramic veneers, and the fracture strength of bilayered zirconia all-ceramic crowns. The role of lithium-disilicate spray-liner at the interface between zirconia and lithium-disilicate glass-ceramic veneers was investigated through surface and cross-sectional analyses. We confirmed that both the mean bonding strength between the zirconia ceramics and lithium-disilicate glass-ceramic veneers and the fracture strength of the liner-treated groups were significantly higher than those of the untreated groups, which resulted, on the one hand, from the chemical bonding at the interface of the zirconia and lithium-disilicate liner, and, on the other, from the existence of a microgap in the group not treated with liner.

Neutron dosimetry using aqueous solutions of lithium acetate

International Nuclear Information System (INIS)

Rakovan, L.J.

1996-01-01

A thermal neutron dosimetry system using the 6 Li(n,α) 3 H reaction and liquid scintillation counting of tritium was developed. Lithium acetate was chosen to supply the 6 Li in the aqueous dosimetry solutions. Neutron irradiations were completed using The Ohio State University Research Reactor. After two sets of samples were irradiated, variables in the system such as the mass of lithium acetate in the solutions and the counting window of the liquid scintillation counter used to analyze the sample were chosen. The system was evaluated by completing two sets of 23 minute irradiations with the reactor at 500 kW, 50 kW, 5 kW, and one irradiation at 500 W. The samples irradiated at 500 W were below the threshold of the system, and could not be used. Prompt analysis was essential due to loss of detectable emissions in the dosimetry solutions over time. The thermal neutron fluences calculated with the data from the samples were compared to the fluences determined from gold wire irradiations. The fluence values differed at most by 6%. The fluence values calculated from the samples were consistently less than those determined from the gold wires

Liquid Scoping Study for Tritium-Lean, Fast Ignition Inertial Fusion Energy Power Plants

International Nuclear Information System (INIS)

Schmitt, R C; Latkowski, J F; Durbin, S G; Meier, W R; Reyes, S

2001-01-01

In a thick-liquid protected chamber design, such as HYLIFE-II, a molten-salt is used to attenuate neutrons and protect the chamber structures from radiation damage. The molten-salt absorbs some of the material and energy given off by the target explosion. In the case of a fast ignition inertial fusion system, advanced targets have been proposed that may be Self-sufficient in the tritium breeding (i.e., the amount of tritium bred in target exceeds the amount burned). These ''tritium-lean'' targets contain approximately 0.5% tritium and 99.5% deuterium, but require a large pr of 10-20 g/cm 2 . Although most of the yield is provided by D-T reactions, the majority of fusion reactions are D-D, which produces a net surplus of tritium. This aspect allows for greater freedom when selecting a liquid for the protective blanket (lithium-bearing compounds are not required). This study assesses characteristics of many single, binary, and ternary molten-salts. Using the NIST Properties of Molten Salts Database, approximately 4300 molten-salts were included in the study [1]. As an initial screening, salts were evaluated for their safety and environmental (SandE) characteristics, which included an assessment of waste disposal rating, contact dose, and radioactive afterheat. Salts that passed the SandE criteria were then evaluated for neutron shielding ability and pumping power. The pumping power was calculated using three components: velocity head losses, frictional losses, and lift. This assessment left us with 57 molten-salts to recommend for further analysis. Many of these molten-salts contain elements such as sodium, lithium, beryllium, boron, fluorine, and oxygen. Recommendations for further analysis are also made

Deuterium trapping in liquid lithium irradiated by deuterium plasma

International Nuclear Information System (INIS)

Pisarev, A.; Moshkunov, K.; Vizgalov, I.; Gasparyan, Yu.

2013-01-01

Liquid lithium was irradiated by deuterium plasma to a low fluence of 10 22 –10 23 D/m 2 , cooled down to room temperature, and then slowly heated. The temperature and release rate were measured during heating. Two plateaus on the temperature–time dependence were observed at 180 °C and 660 °C. The first one corresponds to melting of Li and the second one – either to melting or to decomposition of solid LiD. Features of deuterium release in TDS were interpreted in terms of decomposition of lithium deuterides formed during plasma irradiation

Neutronic investigations on the application of lithium aluminates in the tritium breeding blanket of future fusion reactors

International Nuclear Information System (INIS)

Mohsin, A.

1981-02-01

A survey is given about the state of development work at the blanket. It shows that present designs aim at a fusion reactor with low tritium inventory. This aim can be achieved with a solid blanket. In this paper this concept is described and the selection of appropriate materials for the solid blanket is discussed. The lithium aluminates turned out to be the most suitable materials. Comparing the different lithium aluminates the compounds Li 5 AlO 4 and LiAlO 2 proved to be the most favourable. The improvement of the breeding ratio when using lead as neutron multiplier was investigated. Employing, for example, a lead zone of 15 cm thickness in front of a 60 cm thick breeding zone, the tritium breeding ratio is raised to 1.65 for Li 5 Al 4 and to 1.48 for LiAlO 2 - The originally higher breeding ratio of the Li 5 AlO 4 in contrary to the LiAlO 2 is compensated hereby. By this LiAlO 2 becomes a very interesting material for a solid blanket since it furthermore exhibits a higher melting point and higher phase transition temperature. For experimental check of the nuclear data of this material and the computational techniques used, a test model was designed and built. This blanket model was used for measuring the space-dependent tritium production rate, which could be compared to corresponding computations. The assembly was made of a lead zone as neutron multiplier, LiAlO 2 as breeding material, and polyethylene as neutron reflector. (orig.) [de

Tritium transport and release from lithium ceramic breeder materials

International Nuclear Information System (INIS)

Johnson, C.E.; Kopasz, J.P.; Tam, S.W.

1994-01-01

In an operating fusion reactor,, the tritium breeding blanket will reach a condition in which the tritium release rate equals the production rate. The tritium release rate must be fast enough that the tritium inventory in the blanket does not become excessive. Slow tritium release will result in a large tritium inventory, which is unacceptable from both economic and safety viewpoints As a consequence, considerable effort has been devoted to understanding the tritium release mechanism from ceramic breeders and beryllium neutron multipliers through theoretical, laboratory, and in-reactor studies. This information is being applied to the development of models for predicting tritium release for various blanket operating conditions

Dynamic tritium inventory of a NET/ITER fuel cycle with lithium salt solution blanket

International Nuclear Information System (INIS)

Spannagel, G.; Gierszewski, P.

1991-01-01

At the Karlsruhe Nuclear Research Center (KfK) a flexible tool is being developed to simulate the dynamics of tritium inventories. This tool can be applied to any tritium handling system, especially to the fuel cycle components of future nuclear fusion devices. This instrument of simulation will be validated in equipment to be operated at the Karlsruhe Tritium Laboratory. In this study tritium inventories in a NET/ITER type fuel cycle involving a lithium salt solution blanket are investigated. The salt solution blanket serves as an example because it offers technological properties which are attractive in modeling the process; the example does not impair the general validity of the tool. Usually, the operation strategy of complex structures will deteriorate due to failures of the subsystems involved. These failures together with the reduced availability ensuing from them will be simulated. The example of this study is restricted to reduced availabilities of two subsystems, namely the reactor and the tritium recovery system. For these subsystems the influence of statistically varying intervals of operation is considered. Strategies we selected which are representative of expected modes of operation. In the design of a fuel cycle, care will be taken that prescribed availabilities of the subsystems can be achieved; however, the description of reactor operation is a complex task since operation breaks down into several campaigns for which rules have been specified which enable determination of whether a campaign has been successful and can be stopped. Thus, it is difficult to predict the overall behavior prior to a simulation which includes stochastic elements. Using the example mentioned above the capabilities of the tool will be illustrated; besides the presentation of results of inventory simulation, the applicability of these data will be discussed. (orig.)

Tritium permeation and recovery

International Nuclear Information System (INIS)

Bond, R.A.; Hamilton, A.M.

1987-01-01

The paper is an appendix to a study of the reactor relevance of the NET design concept. The latter study examines whether the technologies and design principles proposed for NET can be directly extrapolated to a demonstration (DEMO) reactor. In this appendix, tritium transport in the DEMO breeding blanket is considered with emphasis on the permeation rate from the lithium-lead breeder into the coolant. A computational model used to calculate the tritium transport in the breeder blanket is described. Results are reported for the tritium transport in the NET/INTOR type blanket as well as the DEMO blanket in order to provide a comparison. In addition, results are presented for the helium coolant tritium extraction analysis. (U.K.)

Experiments on tritium behavior in beryllium, (1)

International Nuclear Information System (INIS)

Kawamura, Hiroshi; Ishizuka, Etsuo; Matsumoto, Mikio; Inada, Seiji; Sezaki, Katsuji; Saito, Minoru; Kato, Mineo.

1989-06-01

In JMTR, it was observed that the tritium concentration of the primary coolant increases with the reactor operation at 50 MW. As one of the tritium generation sources, we paid attention to a neutron reflector made of beryllium because the tritium generation rate in the beryllium is bigger than other components in the reactor core. On the other hand, the irradiation test of blanket materials (i.e. tritium breeding materials and neutron multipling materials) are planned for development of the fusion reactor in JMTR and the beryllium will be also irradiated as a neutron multiplier with tritium breeding materials. Therefore, as the irradiated specimens, we used a hot-pressed beryllium disk fabricated by the same method as the neutron reflector or the neutron multiplier and conducted the irradiation tests in JMTR. The purpose of these tests are to clarify the tritium behavior in the hot-pressed beryllium. In this paper, from a viewpoint of the fabrication of capsules for neutron irradiation, the specifications of the irradiated specimens and capsules are summarized. Additionally, the results on the puncture test of the container of the irradiation specimens are described. (author)

High resolution studies by Secondary Ion Mass Spectrometry of the spatial distribution of tritium in neutron irradiated beryllium pebbles

International Nuclear Information System (INIS)

Rabaglino, E.; Tamborini, G.; Hiernaut, J.-P.; Betti, M.

2006-01-01

A key issue of beryllium as a neutron multiplier in the blanket of future fusion reactors is tritium retention. Models are under development in order to predict tritium release kinetics in the typical operating conditions of the material in the blanket: the absence of experimental data in this range imposes an extrapolation of the models, therefore a detailed characterization and understanding of microscopic diffusion phenomena related to macroscopic tritium release is necessary. It has been recently shown, that the availability of evidence on such phenomena at a scale of 1 micron down to tens of nanometers enables a relevant progress in the effectiveness of model validation: therefore the need for applying and developing advanced analytical techniques based on mass spectrometry at this scale. A study of tritium spatial distribution in neutron irradiated beryllium pebbles (2 mm diameter, 480 appm 4 He, 7 appm 3 H) by means of Secondary Ion Mass Spectrometry (SIMS) is presented. Samples in different conditions (non-irradiated, at end of irradiation and at different temperatures during thermal ramp annealing) are examined by an oxygen ion primary beam with a spatial resolution of 1 micron along a diameter. The sample preparation is optimized in order to enable a quantitative comparison among the different conditions. Under an oxygen ion beam tritium is detected in the irradiated samples in a molecular form (3H 2 ), with a continuous distribution inside the grains, which suggests the presence of small clusters in agreement with TEM analyses, and in the form of peaks at grain boundaries, corresponding to large grain boundary bubbles. The evolving of molecular tritium distribution measured by SIMS during a typical thermal ramp release experiment shows precisely tritium diffusion from the centre of the grain to grain boundaries as the temperature increases: at the same time the remaining intragranular tritium inventory, given by the integral of the distribution

Lithium aluminates and tritium production; Aluminatos de litio y produccion de tritio

Energy Technology Data Exchange (ETDEWEB)

Carrera G, L.M.; Palacios G, O.; Bosch G, P. [Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

1997-07-01

In this work it is studied the crystalline structure of lithium aluminates prepared by three different methods, namely: solid state reaction, humid reaction and sol-gel reaction. The analysis methods are the X-ray diffractometry and the scanning and transmission electron microscopy. This study is realized as in original materials as in irradiated materials at the TRIGA Mark reactor, to correlate the synthesis method with response of these materials to the mixed irradiation of nuclear reactor. (Author)

Tritium release from beryllium pebbles after high temperature irradiation up to 3000 appm He in the HIDOBE-01 experiment

Energy Technology Data Exchange (ETDEWEB)

Til, S. van, E-mail: vantil@nrg.eu [Nuclear Research and Consultancy Group, Westerduinweg 3, Postbus 25, 1755 ZG Petten (Netherlands); Fedorov, A.V.; Stijkel, M.P.; Cobussen, H.L.; Mutnuru, R.K.; Idsert, P. van der [Nuclear Research and Consultancy Group, Westerduinweg 3, Postbus 25, 1755 ZG Petten (Netherlands); Zmitko, M. [The European Joint Undertaking for ITER and The Development of Fusion Energy, c/ Josep Pla, no. 2, Torres Diagonal Litoral, Edificio B3, 08019 Barcelona (Spain)

2013-11-15

In the HIDOBE (HIgh DOse irradiation of BEryllium) irradiation program, various grades of constrained and unconstrained beryllium pebbles, beryllium pellets and titanium-beryllide samples are irradiated in the High Flux Reactor (HFR) in Petten at four different temperatures (between 698 K and 1023 K) for 649 days [1]. The first of two HIDOBE irradiation experiments, HIDOBE-01, was completed after achieving a DEMO relevant helium production level of 3000 appm and the samples are retrieved for postirradiation examination (PIE). This work shows preliminary results of the out-of-pile tritium release analysis performed on different grades of irradiated beryllium pebbles (different in size). Relationships between irradiation temperature, tritium inventory and microstructural evolution have been observed by light microscopy and scanning electron microscopy.

Tritons and tritides as the solute and diffusing species in ceramic tritium breeders

International Nuclear Information System (INIS)

Fischer, A.K.; Johnson, C.E.

1987-01-01

Intragranular diffusion of tritium is an inherent participant in the process of releasing tritium from lithium-containing ceramics that are used to breed tritium in a fusion reactor. The nature of this transport is reviewed in terms of the understanding established for the mechanism of hydrogen migration in other oxides, namely, that the diffusing species is the proton and that it moves from oxide ion to oxide ion, thereby giving rise to apparent hydroxide migration. Analogously, the triton, transiently bonded to successive oxides and forming successive tritoxides, is taken to be the dominant migrating species in ceramic breeders. In addition, tritide becomes a significant participant at low oxygen activity. The relationship of tritons and tritides as the migrating species to the observed release of both reduced and oxidized forms can be understood in terms of the thermodynamic conditions that prevail. Mechanisms exist that can be proposed to rationalize the participation of these species

The impact of tritium solubility and diffusivity on inventory and permeation in liquid breeder blankets

International Nuclear Information System (INIS)

Caorlin, M.; Gervasini, G.; Reiter, F.

1988-01-01

The authors reviewed hydrogen solubility and diffusivity data for liquid lithium-based compounds which are potential breeding blanket materials in NET-type fusion devices. These data have been used to assess tritium permeation and inventory in separately cooled NET blankets and in self cooled blankets with a vanadium first wall. The results for the separately cooled NET-liquid breeder show that tritium permeation is negligible for lithium, a serious problem for Pb-17Li and a critical one for Flibe. The total tritium inventory is lowest in lithium, high in Pb-17Li and very high in Flibe. The high tritium partial pressure for Flibe or Pb-17Li can be reduced in a self cooled blanket with a vanadium first wall. Permeation into the plasma reduces the blanket tritium inventory and permeation. Tritium recovery can be combined with the plasma exhaust

Tritium systems for the TITAN reversed-field pinch fusion reactor design

International Nuclear Information System (INIS)

Martin, R.C.; Sze, D.K.; Bartlit, J.R.; Gierszewski, P.J.

1987-01-01

Tritium systems for the TITAN reversed-field pinch (RFP) fusion reactor study have been designed for two blanket concepts. The TITAN-1 design uses a self-cooled liquid-lithium blanket. The TITAN-2 design uses a self-cooled aqueous-solution blanket, with lithium nitrate dissolved in the water for tritium breeding. Tritium inventory, release, and safety margins are within regulatory limits, at acceptable costs. Major issues for TITAN-1 are plasma-driven permeation, the need for a secondary coolant loop, tritium storage requirements, redundancy in the plasma exhaust system, and minimal isotopic distillation of the exhaust. TITAN-1 fuel cleanup, reprocessing, and air detritiation systems are described in detail

Liquid Scoping Study for Tritium-Lean, Fast Ignition Inertial Fusion Energy Power Plants

Energy Technology Data Exchange (ETDEWEB)

Schmitt, R C; Latkowski, J F; Durbin, S G; Meier, W R; Reyes, S

2001-08-14

In a thick-liquid protected chamber design, such as HYLIFE-II, a molten-salt is used to attenuate neutrons and protect the chamber structures from radiation damage. The molten-salt absorbs some of the material and energy given off by the target explosion. In the case of a fast ignition inertial fusion system, advanced targets have been proposed that may be Self-sufficient in the tritium breeding (i.e., the amount of tritium bred in target exceeds the amount burned). These ''tritium-lean'' targets contain approximately 0.5% tritium and 99.5% deuterium, but require a large pr of 10-20 g/cm{sup 2}. Although most of the yield is provided by D-T reactions, the majority of fusion reactions are D-D, which produces a net surplus of tritium. This aspect allows for greater freedom when selecting a liquid for the protective blanket (lithium-bearing compounds are not required). This study assesses characteristics of many single, binary, and ternary molten-salts. Using the NIST Properties of Molten Salts Database, approximately 4300 molten-salts were included in the study [1]. As an initial screening, salts were evaluated for their safety and environmental (S&E) characteristics, which included an assessment of waste disposal rating, contact dose, and radioactive afterheat. Salts that passed the S&E criteria were then evaluated for neutron shielding ability and pumping power. The pumping power was calculated using three components: velocity head losses, frictional losses, and lift. This assessment left us with 57 molten-salts to recommend for further analysis. Many of these molten-salts contain elements such as sodium, lithium, beryllium, boron, fluorine, and oxygen. Recommendations for further analysis are also made.

In situ tritium from Li2O and Li2ZrO3 irradiated in a fast neutron flux: BEATRIX-II, Phase 1 and 2

International Nuclear Information System (INIS)

Slagle, O.D.; Hollenberg, G.W.; Kurasawa, T.; Verrall, R.A.

1994-06-01

BEATRIX-II was an in situ tritium recovery experiment. This in situ tritium recovery experiment provided data on the performance of Li 2 O and Li 2 ZrO 3 under irradiation conditions covering a range of sweep gas compositions and temperatures. The experiment consisted of two separate irradiation cycles which in turn included two vented tritium recovery canisters each. Phase 1 operated for 300 Effective Full Power Days (EFPD) while Phase 2 operated for 203 EFPD of irradiation. The tritium recovery behavior of Li 2 O and Li 2 ZrO 3 was characterized using temperature transients, sweep gas composition changes and reactor power changes to effect changes in the tritium inventory. The high neutron flux level in FFTF resulted in high tritium generation rates which combined with a responsive tritium measurement system allowed detailed observations on the tritium recovery behavior of Li 2 O and Li 2 ZrO 3 . During the course of the experiment a number of observations were made which did not appear consistent with a simplified view of the tritium recovery behavior of these materials. These observations included small negative tritium recovery peaks preceding the typical primary positive peaks; and, for specific temperature ranges, changes in tritium inventory which where opposite to the characteristic expected changes

Design of a permeator against vacuum for tritium extraction from eutectic lithium-lead in a DCLL DEMO

Energy Technology Data Exchange (ETDEWEB)

Garcinuño, Belit, E-mail: belit.garcinuno@ciemat.es [CIEMAT-LNF (Laboratorio Nacional de Fusión), Madrid (Spain); Rapisarda, David [CIEMAT-LNF (Laboratorio Nacional de Fusión), Madrid (Spain); Fernández, Iván [Fundación & Departamento de Ingeniería Energética, UNED, Madrid (Spain); CIEMAT-LNF (Laboratorio Nacional de Fusión), Madrid (Spain); Moreno, Carlos; Palermo, Iole; Ibarra, Ángel [CIEMAT-LNF (Laboratorio Nacional de Fusión), Madrid (Spain)

2017-04-15

Highlights: • A conceptual design of a Permeator Against Vacuum is presented. • The efficiency is dependent on geometry and Tritium transport. • The use of different membrane materials is discussed. • A squared PAV with alternated PbLi flowing and vacuum flat ducts is designed. • 80% efficiency of Tritium extraction is accomplished under DCLL-BB requirements. - Abstract: One of the most important issues in future fusion power plants is the extraction of tritium generated in the breeders in order to achieve self-sufficiency. When the breeder is a liquid metal one of the most promising techniques is the Permeation Against Vacuum, whose principle is based on tritium diffusion through a permeable membrane in contact with the liquid metal carrier and its further extraction by a vacuum pump. A conceptual design of permeator has been developed, taking into account the features of a DEMO reactor with a Dual Coolant Lithium Lead (DCLL) breeder blanket. The study is based on the analysis of different membranes and geometries aiming at the overall efficiency (extraction capability) of the device, as well as its compatibility with the breeder material. The permeator is based on a rectangular section multi-channel distribution where the liquid metal channels and vacuum channels are alternated in order to maximize the contact area and therefore to promote tritium transport from the bulk to the walls. The resulting permeator design has an excellent estimated extraction efficiency, of 80%, in a relatively compact device.

Tritium breeding blanket

International Nuclear Information System (INIS)

Smith, D.; Billone, M.; Gohar, Y.; Baker, C.; Mori, S.; Kuroda, T.; Maki, K.; Takatsu, H.; Yoshida, H.; Raffray, A.; Sviatoslavsky, I.; Simbolotti, G.; Shatalov, G.

1991-01-01

The terms of reference for ITER provide for incorporation of a tritium breeding blanket with a breeding ratio as close to unity as practical. A breeding blanket is required to assure an adequate supply of tritium to meet the program objectives. Based on specified design criteria, a ceramic breeder concept with water coolant and an austenitic steel structure has been selected as the first option and lithium-lead blanket concept has been chosen as an alternate option. The first wall, blanket, and shield are integrated into a single unit with separate cooling systems. The design makes extensive use of beryllium to enhance the tritium breeding ratio. The design goals with a tritium breeding ratio of 0.8--0.9 have been achieved and the R ampersand D requirements to qualify the design have been identified. 4 refs., 8 figs., 2 tabs

Neutronics and activation analysis of lithium-based ternary alloys in IFE blankets

Energy Technology Data Exchange (ETDEWEB)

Jolodosky, Alejandra, E-mail: aleja311@berkeley.edu [University of California Berkeley, Berkeley, CA 94706 (United States); Kramer, Kevin [Lawrence Livermore National Laboratory, P.O. Box 808, Livermore, CA (United States); Meier, Wayne; DeMuth, James; Reyes, Susana [TerraPower, Bellevue, WA 98005 (United States); Fratoni, Massimiliano [University of California Berkeley, Berkeley, CA 94706 (United States)

2016-06-15

Highlights: • Monte Carlo calculations were performed on numerous lithium ternary alloys. • Elements with high neutron multiplication performed well with low absorbers. • Enriching lithium decreases minimum lithium concentration of alloys by 60% or more. • Alloys that performed well neutronically were selected for activation calculations. • Alloys activated, except LiBaBi, do not pose major environmental or safety concerns. - Abstract: An attractive feature of using liquid lithium as the breeder and coolant in fusion blankets is that it has very high tritium solubility and results in very low levels of tritium permeation throughout the facility infrastructure. However, lithium metal vigorously reacts with air and water and presents plant safety concerns. The Lawrence Livermore National Laboratory is carrying an effort to develop a lithium-based ternary alloy that maintains the beneficial properties of lithium (e.g. high tritium breeding and solubility) and at the same time reduces overall flammability concerns. This study evaluates the neutronics performance of lithium-based alloys in the blanket of an inertial fusion energy chamber in order to inform such development. 3-D Monte Carlo calculations were performed to evaluate two main neutronics performance parameters for the blanket: tritium breeding ratio (TBR), and the fusion energy multiplication factor (EMF). It was found that elements that exhibit low absorption cross sections and higher q-values such as Pb, Sn, and Sr, perform well with those that have high neutron multiplication such as Pb and Bi. These elements meet TBR constrains ranging from 1.02 to 1.1. However, most alloys do not reach EMFs greater than 1.15. Additionally, it was found that enriching lithium with {sup 6}Li significantly increases the TBR and decreases the minimum lithium concentration by more than 60%. The amount of enrichment depends on how much total lithium is in the alloy to begin with. Alloys that performed well in the TBR

Methodology for tritium recovery as a by-product in the fluorine 18 production

International Nuclear Information System (INIS)

Flores Rea, H.

1990-01-01

In this paper previous studies for the recuperation of waste tritium proceeding from the process used to produce F-18 using natural and 95% enriched lithium carbonate in lithium-6 are presented; the nuclear reaction took place in the Triga Mark III Nuclear reactor of the Nuclear Centre of Mexico. Previous studies proved the importance of the quantity of remanent tritium in the solutions where F-18 was produced in oxygenated compounds of natural lithium. The recuperation methodology consisted in production of F-18 in the established manner, purification by chromatography in an alumina and ion exchange resins column and of waste solutions; these were put together and distilled at normal pressure until dry. The distilled products were concentrated using an electrochemical method, and a final treatment system of the sample based on one reported in the literature but adapted to concentrate smaller volumes (approximately 15 ml.). The samples coming from the enriched lithium carbonate contained 3 to 6 times more tritium than those of natural lithium carbonate. Approximately 30% of the initial considered quantity of lithium was recuperated. A modification to the proposed methodology will allow the recuperation of tritium in waste solutions of F-18 in a percentage higher than 80%. (Author)

Quantitative determination of tritium in metals and oxides

International Nuclear Information System (INIS)

Vance, D.E.; Smith, M.E.; Waterbury, G.R.

1979-04-01

Metallic samples are analyzed for tritium by heating the sample at 1225 K in a moist oxygen stream. The volatile products are trapped and the tritium is quantitatively determined by scintillation spectroscopy. The method is used to determine less than 1 ppb of tritium in 100-mg samples of lithium, iron, nickel, cerium, plutonium, and plutonium dioxide. Analysis of 18 cuts of a tritium-zirconium, copper foil standard over a 3-yr period showed a tritium content of 45 ppM and a standard deviation of 6 ppM

Trace hydrogen extraction from liquid lithium tin alloy

International Nuclear Information System (INIS)

Xie Bo; Hu Rui; Xie Shuxian; Weng Kuiping

2010-01-01

In order to finish the design of tritium extraction system (TES) of fusion fission hybrid reactor (FFHR) tritium blanket, involving the dynamic mathematical model of liquid metal in contact with a gaseous atmosphere, approximate mathematical equation of tritium in lithium tin alloy was deduced. Moreover, carrying process used for trace hydrogen extraction from liquid lithium tin alloy was investigated with hydrogen being used to simulate tritium in the study. The study results indicate that carrying process is effective way for hydrogen extraction from liquid lithium tin alloy, and the best flow velocity of carrier gas is about 4 L/min under 1 kg alloy temperatures and carrying numbers are the main influencing factors of hydrogen number. Hydrogen extraction efficiency can reach 85% while the alloy sample is treated 6 times at 823 K. (authors)

LIBRETTO-3: Performance of tritium permeation barriers under irradiation at the HFR Petten

International Nuclear Information System (INIS)

Conrad, R.; Fuetterer, M.A.; Giancarli, L.; May, R.; Perujo, A.; Sample, T.

1994-01-01

The LIBRETTO-3 irradiation was performed at the HFR Petten during 77 full power days in three cycles to compare the efficiency of three different tritium permeation barriers in presence of Pb-17Li to uncoated AISI 316L steel. For this purpose four steel capsules (arnothing o =10 mm, arnothing i =8 mm, l=300 mm) were filled with 28 g Pb-17Li. The coatings included CVD TiC (outside), CVD TiC+Al 2 O 3 (inside), and pack cementation aluminisation (inside). The generated tritium was partly extracted by bubbling, partly it permeated through the capsules. Permeated and extracted tritium were measured as a function of temperature (280-450 C), H 2 doping (0-1 vol%) and purge gas flow rate. The driving partial pressure in the coated capsules were from an extraction model calibrated by the uncoated capsule for which tritium partial pressure could be calculated. In LIBRETTO-3 conditons, the best barrier was pack cementation aluminisation. The first interpretation of the experiment could, however, not confirm permeation reduction factors of 100 or more expected from this barrier. ((orig.))

Tritium dosimetry and standardization

International Nuclear Information System (INIS)

Balonov, M.I.

1983-01-01

Actual problem of radiation hygiene such as an evaluation of human irradiation hazard due to a contact with tritium compounds both in industrial and public spheres is under discussion. Sources of tritium release to environment are characterized. Methods of tritium radiation monitoring are discussed. Methods of dosimetry of internal human exposure resulted from tritium compounds are developed on the base of modern representations on metbolism and tritium radiobiological effect. A system of standardization of permissible intake of tritium compounds for personnel and persons of population is grounded. Some protection measures are proposed as applied to tritium overdosage

Fusion Materials Irradiation Test Facility: a facility for fusion-materials qualification

International Nuclear Information System (INIS)

Trego, A.L.; Hagan, J.W.; Opperman, E.K.; Burke, R.J.

1983-01-01

The Fusion Materials Irradiation Test Facility will provide a unique testing environment for irradiation of structural and special purpose materials in support of fusion power systems. The neutron source will be produced by a deuteron-lithium stripping reaction to generate high energy neutrons to ensure damage similar to that of a deuterium-tritium neutron spectrum. The facility design is now ready for the start of construction and much of the supporting lithium system research has been completed. Major testing of key low energy end components of the accelerator is about to commence. The facility, its testing role, and the status and major aspects of its design and supporting system development are described

Tritium

International Nuclear Information System (INIS)

Anon.

1975-01-01

The role played the large amount supply of tritium and its effects are broadly reviewed. This report is divided into four parts. The introductory part includes the history of tritium research. The second part deals with the physicochemical properties of tritium and the compounds containing tritium such as tritium water and labeled compounds, and with the isotope effects and self radiation effects of tritium. The third part deals with the tritium production by artificial reaction. Attention is directed to the future productivity of tritium from B, Be, N, C, O, etc. by using the beams of high energy protons or neutrons. The problems of the accepting market and the accuracy of estimating manufacturing cost are discussed. The expansion of production may bring upon the reduction of cost but also a large possibility of social impact. The irradiation problem and handling problem in view of environmental preservation are discussed. The fourth part deals with the use of tritium as a target, as a source of radiation or light, and its utilization for geochemistry. The future development of the solid tritium target capable of elongating the life of neutron sources is expected. The rust thickness of the surface of iron can be measured with the X-ray of Ti-T or Zr-T. The tritium can substitute self-light emission paint or lamp. The tritium is suitable for tracing the movement of sea water and land surface water because of its long half life. (Iwakiri, K.)

Formation and properties of radiation-induced defects and radiolysis products in lithium orthosilicate

Energy Technology Data Exchange (ETDEWEB)

Tiliks, J.E.; Kizane, G.K.; Supe, A.A.; Abramenkovs, A.A.; Tiliks, J.J. (Latvian Univ., Riga (Latvia)); Vasiljev, V.G. (Acad. A.A. Bochvar Inst. of Inorganic Materials, Moscow (USSR))

1991-12-01

Formation and properties of radiation-induced defects and radiolysis products in polycrystalline powders and ceramic pellets of Li{sub 4}SiO{sub 4} were studied under the effect of various types of ionizing irradiation ({gamma} quants, accelerated electrons, reactor irradiation), humidity, temperature, impurities in the samples, etc. The content of radiation defects and radiolysis products poorly depends on irradiation type, dose rate, admixture elements. The concentration of defects highly depends on the temperature of irradiation, humidity, granural size. Empirical dependence of radiolysis degree {alpha} on the dose was found: {alpha}=5x10{sup -2}xD{sup 0.5} for {gamma} and electron irradiation (T{sub rad}=300-350 K) and {alpha}=5x10{sup -3}xD{sup 0.5} for reactor radiation (T{sub rad}=700-800 K); {alpha} - matrix dissociation degree (in %); D - dose (in MGy). Colloidal lithium and silicon, lithium and silicon oxides, and O{sub 2} are the final products of radiolysis. Radiation-induced defects change tritium thermo-extraction parameters, deteriorate mechanical, thermo-physical and electric properties of ceramics. (orig.).

Preliminary study on lithium-salt aqueous solution blanket

International Nuclear Information System (INIS)

Yoshida, Hiroshi; Naruse, Yuji; Yamaoka, Mitsuaki; Ohara, Atsushi; Ono, Kiyoshi; Kobayashi, Shigetada.

1992-06-01

Aqueous solution blanket using lithium salts such as LiNO 3 and LiOH have been studied in the US-TIBER program and ITER conceptual design activity. In the JAERI/LANL collaboration program for the joint operation of TSTA (Tritium Systems Test Assembly), preliminary design work of blanket tritium system for lithium ceramic blanket, aqueous solution blanket and liquid metal blanket, have been performed to investigate technical feasibility of tritium demonstration tests using the TSTA. Detail study of the aqueous solution blanket concept have not been performed in the Japanese fusion program, so that this study was carried out to investigate features of its concept and to evaluated its technical problems. The following are the major items studied in the present work: (i) Neutronics of tritium breeding ratio and shielding performance Lithium concentration, Li-60 enrichment, beryllium or lead, composition of structural material/beryllium/solution, heavy water, different lithium-salts (ii) Physicochemical properties of salts Solubility, corrosion characteristics and compatibility with structural materials, radiolysis (iii) Estimation of radiolysis in ITER aqueous solution blanket. (author)

Thermal-hydraulic calculation and analysis on helium cooled ceramic breeder pebble bed assembly for in-pile irradiation and in-situ tritium extraction

International Nuclear Information System (INIS)

Guo Chunqiu; Xie Jiachun; Liu Xingmin

2013-01-01

In-pile irradiation and in-situ tritium extraction experiment is one of associated domestic research projects in ITER special program. According to the technical requirements of in-pile irradiation experiment of helium cooled ceramic breeder (ceramic) pebble bed assembly in a research reactor, the feasibility of the design for the in-pile irradiation and in-situ tritium extraction experiment of ceramic pebble bed assembly was evaluated. By conducting thermal-hydraulic design calculation with different in-pile irradiation channels, locations and structure parameters for ceramic pebble bed assembly, a reasonable design scheme of ceramic pebble bed assembly satisfying the design requirements for in-pile irradiation was obtained. (authors)

HEINBE; the calculation program for helium production in beryllium under neutron irradiation

International Nuclear Information System (INIS)

Shimakawa, Satoshi; Ishitsuka, Etsuo; Sato, Minoru

1992-11-01

HEINBE is a program on personal computer for calculating helium production in beryllium under neutron irradiation. The program can also calculate the tritium production in beryllium. Considering many nuclear reactions and their multi-step reactions, helium and tritium productions in beryllium materials irradiated at fusion reactor or fission reactor may be calculated with high accuracy. The calculation method, user's manual, calculated examples and comparison with experimental data were described. This report also describes a neutronics simulation method to generate additional data on swelling of beryllium, 3,000-15,000 appm helium range, for end-of-life of the proposed design for fusion blanket of the ITER. The calculation results indicate that helium production for beryllium sample doped lithium by 50 days irradiation in the fission reactor, such as the JMTR, could be achieved to 2,000-8,000 appm. (author)

Study of tritium decontamination of stainless steel, copper, aluminum metals by tritium dry desorption

International Nuclear Information System (INIS)

Xie Yun; Shi Zhengkun; Wu Tao

2014-01-01

In order to study the decontamination efficiency of stainless steel, copper, aluminum metals contaminated by tritium, the metals were decontaminated by exposing to UV, ozone, heating, and the combination of heating, UV and ozone. The result indicates that the elevation of temperature can obviously improve decontamination. While irradiated by 172 nm UV, the decontamination efficiency is low, but it is better while heated and irradiated by 172 nm UV. If the stainless steel is irradiated by 172 nm UV and heated at 500℃ for 4 h, the decontamination efficiency is 99.2%. There is better decontamination efficiency of copper while exposed to ozone. While exposed to ozone and heated at 500℃, the decontamination efficiencies of stainless steel, copper and aluminum are higher than 99.2%. The decontamination efficiency can more obviously improve when metal is heated at high temperature (500℃) than low temperature (300℃). The surface tritium of metal placed at 30 d after decontamination increases because of diffusion and penetration of the tritium. Resolution spectra of tritium show that there are four kinds of contamination adsorbed tritium of stainless steel. (authors)

Removal of contaminating tritium and tritium pressure measurement by a secondary electron multiplier

International Nuclear Information System (INIS)

Ichimura, K.; Watanabe, K.; Nishizawa, K.; Fujita, J.

1984-01-01

A ceramic secondary electron multiplier (SEM), Ceratron, was used to study impairment of the SEM performance due to adsorbed tritium, its decontamination, and the applicability of the SEM to measure tritium pressure. The background level of the SEM increased significantly, up to its counting limit, due to tritium adsorption. Heating it to 300 0 C in vacuo and/or in the presence of reactive gases such as D 2 and CO at 1 x 10 -4 Pa was not effective to decontaminate the SEM, whereas photon irradiation was extremely powerful for the decontamination. The tritium (HT) pressure in a range of 1 x 10 -6 - 1 x 10 -3 Pa could be measured with no significant impairment of the SEM performance with the aid of photon irradiation. It is revealed that a particle flux as low as 1 particle/s will be able to measure in the presence of tritium if suitable photon sources are installed in the systems. (orig.)

Experiences with decontaminating tritium-handling apparatus

International Nuclear Information System (INIS)

Maienschein, J.L.; Garcia, F.; Garza, R.G.; Kanna, R.L.; Mayhugh, S.R.; Taylor, D.T.

1992-01-01

Tritium-handling apparatus has been decontaminated as part of the downsizing of the LLNL Tritium Facility. Two stainless-steel glove boxes that had been used to process lithium deuteride-tritide (LiDT) slat were decontaminated using the Portable Cleanup System so that they could be flushed with room air through the facility ventilation system. In this paper the details on the decontamination operation are provided. A series of metal (palladium and vanadium) hydride storage beds have been drained of tritium and flushed with deuterium, in order to remove as much tritium as possible. The bed draining and flushing procedure is described, and a calculational method is presented which allows estimation of the tritium remaining in a bed after it has been drained and flushed. Data on specific bed draining and flushing are given

Tritium system design studies of fusion experimental breeder

International Nuclear Information System (INIS)

Deng Baiquan; Huang Jinhua

2003-01-01

A summary of the tritium system design studies for the engineering outline design of a fusion experimental breeder (FEB-E) is presented. This paper is divided into three sections. In first section, the geometry, loading features and tritium concentrations in liquid lithium of tritium breeding zones of blanket are described. The tritium flow chart corresponding to the tritium fuel cycle system has been constructed, and the inventories in ten subsystems are calculated using SWITRIM code in section 2. Results show that the necessary initial tritium storage to start up FEB-E with fusion power of 143 MW is about 319 g. In final section, the tritium leakage issues under different operation circumstances have been analyzed. It was found that the potential danger of tritium leakage could be resulted from the exhausted gas of the diverter system. It is important to elevate the tritium burnup fraction and reduce the tritium throughput. (authors)

Tritium-assisted fusion breeders

International Nuclear Information System (INIS)

Greenspan, E.; Miley, G.H.

1983-08-01

This report undertakes a preliminary assessment of the prospects of tritium-assisted D-D fuel cycle fusion breeders. Two well documented fusion power reactor designs - the STARFIRE (D-T fuel cycle) and the WILDCAT (Cat-D fuel cycle) tokamaks - are converted into fusion breeders by replacing the fusion electric blankets with 233 U producing fission suppressed blankets; changing the Cat-D fuel cycle mode of operation by one of the several tritium-assisted D-D-based modes of operation considered; adjusting the reactor power level; and modifying the resulting plant cost to account for the design changes. Three sources of tritium are considered for assisting the D-D fuel cycle: tritium produced in the blankets from lithium or from 3 He and tritium produced in the client fission reactors. The D-D-based fusion breeders using tritium assistance are found to be the most promising economically, especially the Tritium Catalyzed Deuterium mode of operation in which the 3 He exhausted from the plasma is converted, by neutron capture in the blanket, into tritium which is in turn fed back to the plasma. The number of fission reactors of equal thermal power supported by Tritium Catalyzed Deuterium fusion breeders is about 50% higher than that of D-T fusion breeders, and the profitability is found to be slightly lower than that of the D-T fusion breeders

Irradiation damage in gamma lithium aluminate - LiAlO2

International Nuclear Information System (INIS)

Auvray-Gely, M.H.

1989-01-01

Single crystals of gamma lithium aluminate (of tetragonal structure) are irradiated) with various projectiles (electrons, He ions, protons, X and gamma photons) and we used (i) electronic paramagnetic resonance (EPR) and optical absorption to detect the defects produced, and (ii) transmission electron microscopy (TEM). The lithium aluminate single crystals irradiated with electrons or ions contain five different paramagnetic defects. Each of them has several anisotropic configurations whose EPR signals (i) have a Lande factor close to 2, (ii) exhibit a resolved hyperfine structure and (iii) are identical only when the static magnetic field is along /001/. In addition, four optical absorption bands appear in the range 1-6 eV in the same irradiation conditions. But only three among the five paramagnetic defects and one of the optical bands appear in X-and gamma-ray irradiated samples. Using these observations, we discuss the nature of the detected defects and we conclude about the type of their production mechanism. Particularly, we assign a six-line EPR signal and an optical band in the ultraviolet range to the F + -centre. We compare this hypothesis to a defect model based on the computation of approximate electronic wave functions using the variational method. Our TEM study shows that when gamma-LiAlO 2 single crystals are irradiated with 1 MeV electrons (fluence: 10 20 electrons/sqcm), tridimensional defects (of mean dimension 100 nm) appear. At lower energies, the defect production is hidden by a thermal effect that is sufficient to induce the evaporation of lithium oxyde and the formation of LiAl 5 0 8 [fr

[Effect of hydrofluoric acid concentration on the surface morphology and bonding effectiveness of lithium disilicate glass ceramics to resin composites].

Science.gov (United States)

Hailan, Qian; Lingyan, Ren; Rongrong, Nie; Xiangfeng, Meng

2017-12-01

This study aimed at determining the influence of hydrofluoric acid (HF) in varied concentrations on the surface morphology of lithium disilicate glass ceramics and bond durability between resin composites and post-treated lithium disilicate glass ceramics. After being sintered, ground, and washed, 72 as-prepared specimens of lithium disilicate glass ceramics with dimensions of 11 mm×13 mm×2 mm were randomly divided into three groups. Each group was treated with acid solution [32% phosphoric acid (PA) or 4% or 9.5% HF] for 20 s. Then, four acidified specimens from each group were randomly selected. One of the specimens was used to observe the surface morphology using scanning electron microscopy, and the others were used to observe the surface roughness using a surface roughness meter (including Ra, Rz, and Rmax). After treatment with different acid solutions in each group, 20 samples were further treated with silane coupling agent/resin adhesive/resin cement (Monobond S/Multilink Primer A&B/Multilink N), followed by bonding to a composite resin column (Filtek™ Z350) with a diameter of 3 mm. A total of 20 specimens in each group were randomly divided into two subgroups, which were used for measuring the microshear bond strength, with one of them subjected to cool-thermal cycle for 20 000 times. The surface roughness (Ra, Rz, and Rmax) of lithium disilicate glass ceramics treated with 4% or 9.5% HF was significantly higher than that of the ceramic treated with PA (Pglass ceramics treated with 9.5% HF also demonstrated better surface roughness (Rz and Rmax) than that of the ceramics treated with 4% HF. Cool-thermal cycle treatment reduced the bond strength of lithium disilicate glass ceramics in all groups (Pglass ceramics treated with HF had higher bond strength than that of the ceramics treated with PA. The lithium disilicate glass ceramics treated with 4% HF had higher bond strength than that of the ceramics treated with 9.5% HF (Pglass ceramics treated with 4

Effect of the addition of lithium carbonate on the properties of low density polyethylene

International Nuclear Information System (INIS)

Hoshimura, Yoshikazu; Yamamoto, Shigeru

1992-01-01

For improvement of the properties of polyethylene (PE), γ-ray was irradiated to the lithium carbonate added PE. An increase in the numbers of OH and C=C bonds was observed from FT-IR measurements. The melting temperature (or the vanishing temperature of crystallinity by X-ray diffraction) of the lithium carbonate added PE after γ-ray irradiation (10 6 Gy) was 20degC higher than that of the PE's with no additives and with quartz added PE. The lamellae of lithium carbonate added PE were not observed in the scanning electron micrographs. This vanishing of lamellae of the lithium carbonate added PE was also suggested by the extinction of the maltese cross with a polarizing microscope. (author)

Tritium analysis at TFTR

International Nuclear Information System (INIS)

Voorhees, D.R.; Rossmassler, R.L.; Zimmer, G.

1995-01-01

The tritium analytical system at TFRR is used to determine the purity of tritium bearing gas streams in order to provide inventory and accountability measurements. The system includes a quadrupole mass spectrometer and beta scintillator originally configured at Monsanto Mound Research Laboratory in the late 1970's and early 1980's. The system was commissioned and tested between 1991 and 1992 and is used daily for analysis of calibration standards, incoming tritium shipments, gases evolved from uranium storage beds and measurement of gases returned to gas holding tanks. The low resolution mass spectrometer is enhanced by the use of a metal getter pump to aid in resolving the mass 3 and 4 species. The beta scintillator complements the analysis as it detects tritium bearing species that often are not easily detected by mass spectrometry such as condensable species or hydrocarbons containing tritium. The instruments are controlled by a personal computer with customized software written with a graphical programming system designed for data acquisition and control. A discussion of the instrumentation, control systems, system parameters, procedural methods, algorithms, and operational issues will be presented. Measurements of gas holding tanks and tritiated water waste streams using ion chamber instrumentation are discussed elsewhere

Management of tritium at nuclear facilities

International Nuclear Information System (INIS)

1984-01-01

This report presents extending summaries of the works of the participants to an IAEA co-ordinated research programme, ''Handling Tritium - bearing effluents and wastes''. The subjects covered include production of tritium in nuclear power plants (mainly heavy water and light water reactors), as well as at reprocessing plants; removal and enrichment of tritium at nuclear facilities; conditioning methods and characteristics of immobilized tritium of low and high concentration; some potential methods of storage and disposal of tritium. In addition to the conclusions of this three-years work, possible activities in the field are recommended

Sublethal effects of tritium on aquatic systems. Ecological effects of lithium and beryllium on aquatic communities. Teratological effects of low-level magnetic fields

International Nuclear Information System (INIS)

Strand, J.A.; Poston, T.M.; Skalaski, J.R.; Emery, R.M.; Klopfer, D.C.; Abernethy, C.S.

1981-01-01

Studies of the sublethal effects of tritium on the relatively radiosensitive immune process of the rainbow trout suggest that a higher RBE value than is now recognized by the International Commission on Radiological Protection (ICRP) may be required. Studies included an evaluation of potential toxicity of lithium on embryological life of rainbow trout and an assessment of fate and effects of lithium in artificial stream habitats. Levels of lithium necessary to cause an observed effect would have to be at least three orders of magnitude above observed background. Studies on teratogenic effects of low-level magnetic fields address the need to assess the potential harmful effects of magnetic fields on attendant personnel working in the transport and hot cell areas of fusion reactors

Dosimetric properties of dysprosium doped lithium borate glass irradiated by 6 MV photons

International Nuclear Information System (INIS)

Ab Rasid, A.; Wagiran, H.; Hashim, S.; Ibrahim, Z.; Ali, H.

2015-01-01

Undoped and dysprosium doped lithium borate glass system with empirical formula (70–x) B 2 O 3 –30 Li 2 O–(x) Dy 2 O 3 (x=0.1, 0.3, 0.5, 0.7, 1.0 mol%) were prepared using the melt-quenching technique. The dosimetric measurements were performed by irradiating the samples to 6 MV photon beam using linear accelerator (LINAC) over a dose range of 0.5–5.0 Gy. The glass series of dysprosium doped lithium borate glass produced the best thermoluminescence (TL) glow curve with the highest intensity peak from sample with 1.0 mol% Dy 2 O 3 concentration. Minimum detectable dose was detected at 2.24 mGy, good linearity of regression coefficient, high reproducibility and high sensitivity compared to the undoped glass are from 1.0 mol% dysprosium doped lithium borate glass. The results indicated that the series of dysprosium doped lithium glasses have a great potential to be considered as a thermoluminescence dosimetry (TLD). - Highlights: • TL response of undoped and dysprosium doped lithium borate glass subjected to 6 MV photons irradiation at low dose range. • TL linear response of dysprosium doped lithium borate glass. • The sensitivity of dysprosium doped lithium borate glass is approximately 93 times higher than undoped glass

Conceptual design of tritium accountancy system for LLCB TBM

International Nuclear Information System (INIS)

Patel, Rudreksh; Sircar, Amit

2017-01-01

Lead Lithium Ceramic Breeder (LLCB) Test Blanket Module (TBM) will be tested in ITER for performance evaluation of high grade of heat extraction and tritium breeding. The bred tritium in the breeder materials is extracted and recovered by Tritium Extraction System (TES), whereas tritium permeated from breeder materials to helium coolants, viz., primary coolant and secondary coolant, is recovered by Coolant Purification System (CPS). This recovered tritium has to be accounted before transferring it to tritium plant (i.e., ITER inner fuel). This tritium accountancy is performed by Tritium Accountancy System (TAS). In addition to tritium accountancy, TAS also provides necessary data for the validation of design and modelling tools.In this work, we have presented conceptual design of TAS. It also describes operational philosophy, process parameters, process flow diagram, and interface details with ITER tritium plant. (author)

Fusion Materials Irradiation Test (FMIT) facility lithium system: a design and development status

International Nuclear Information System (INIS)

Brackenbury, P.J.; Bazinet, G.D.; Miller, W.C.

1983-01-01

The design and development of the Fusion Materials Irradiation Test (FMIT) Facility lithium system is outlined. This unique liquid lithium recirculating system, the largest of its kind in the world, is described with emphasis on the liquid lithium target assembly and other important components necessary to provide lithium flow to the target. The operational status and role of the Experimental Lithium System (ELS) in the design of the FMIT lithium system are discussed. Safety aspects of operating the FMIT lithium system in a highly radioactive condition are described. Potential spillage of the lithium is controlled by cell liners, by argon flood systems and by remote maintenance features. Lithium chemistry is monitored and controlled by a side-stream loop, where impurities measured by instruments are collected by hot and cold traps

Fusion Materials Irradiation Test (FMIT) facility lithium system: a design and development status

Energy Technology Data Exchange (ETDEWEB)

Brackenbury, P.J.; Bazinet, G.D.; Miller, W.C.

1983-01-01

The design and development of the Fusion Materials Irradiation Test (FMIT) Facility lithium system is outlined. This unique liquid lithium recirculating system, the largest of its kind in the world, is described with emphasis on the liquid lithium target assembly and other important components necessary to provide lithium flow to the target. The operational status and role of the Experimental Lithium System (ELS) in the design of the FMIT lithium system are discussed. Safety aspects of operating the FMIT lithium system in a highly radioactive condition are described. Potential spillage of the lithium is controlled by cell liners, by argon flood systems and by remote maintenance features. Lithium chemistry is monitored and controlled by a side-stream loop, where impurities measured by instruments are collected by hot and cold traps.

Comparison of integral values for measured and calculated fast neutron spectra in lithium fluoride piles

International Nuclear Information System (INIS)

Sekimoto, Hiroshi

1989-01-01

The tritium production density, kerma heat production density, dose and certain integral values of scalar neutron spectra in bare and graphite-reflected lithium-fluoride piles irradiated with D-T neutrons were evaluated from the pulse height distribution of a miniature NE213 neutron spectrometer with UFO data processing code, and compared with the values calculated with MORSE-CV Monte Carlo code. (author). 8 refs.; 1 fig.; 2 tabs

Radiation damage and defect behavior in proton irradiated lithium-counterdoped n+p silicon solar cells

Science.gov (United States)

Stupica, John; Goradia, Chandra; Swartz, Clifford K.; Weinberg, Irving

1987-01-01

Two lithium-counterdoped n+p silicon solar cells with different lithium concentrations were irradiated by 10-MeV protons. Cell performance was measured as a function of fluence, and it was found that the cell with the highest concentration of lithium had the highest radiation resistance. Deep level transient spectroscopy which showed two deep level defects that were lithium related. Relating the defect energy levels obtained from this study with those from earlier work using 1-MeV electron irradiation shows no correlation of the defect energy levels. There is one marked similarity: the absence of the boron-interstitial-oxygen-interstitial defect. This consistency strengthens the belief that lithium interacts with oxygen to prevent the formation of the boron interstitial-oxygen interstitial defect. The results indicate that, in general, addition of lithium in small amounts to the p-base of a boron doped silicon solar cell such that the base remains p-type, tends to increase the radiation resistance of the cell.

Sol-gel synthesis of lithium metatitanate as tritium breeding material under different sintering conditions

Science.gov (United States)

Lu, Wei; Wang, Jing; Pu, Wenjing; Li, Kaiping; Ma, Shubing; Wang, Weihua

2018-04-01

Lithium metatitanate (Li2TiO3) is a promising tritium breeding material candidate for solid blanket of D-T fusion reactors, due to its high mechanical strength, chemical stability, and tritium release rate. In this paper, Li2TiO3 powder with homogeneous crystal structure is synthesized by sol-gel method. The chemical reactions in gel thermal cracking and sintering process are studied by thermo gravimetric/differential scanning calorimetry (TG-DSC). The relationship between the sintering condition and the particle/grain size is characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Results show that below 673 K the gel precursor is completely decomposed and Li2TiO3 phase initially forms. The LiTiO2 by-product formed under the reductive atmosphere in muffle furnace, could be oxidized continually to Li2TiO3 at higher sintering temperature (≥1273 K) for longer sintering time (≥10 h). Both grain and particle sizes rely on a linear growth with the increase of sintering time at 1273 K. Over 1473 K, significant agglomerations exist among particles. The optimal sintering condition is selected as 1273 K for 10 h, for the purer Li2TiO3 phase (>99%), smaller grain and particle size.

Topical report on a preconceptual design for the Spallation-Induced Lithium Conversion (SILC) target for the accelerator production of tritium (APT)

International Nuclear Information System (INIS)

Van Tuyle, G.J.; Cokinos, D.M.; Czajkowski, C.; Franz, E.M.; Kroeger, P.; Todosow, M.; Youngblood, R.; Zucker, M.

1993-01-01

The preconceptual design of the APT Li-Al target system, also referred to as the Spallation-Induced Lithium Conversion (SILC), target system, is summarized in this report. The system has been designed to produce a ''3/8 Goal'' quantity of tritium using the 200-mA, 1.0 GeV proton beam emerging from the LANL-designed LINAC. The SILC target system consists of a beam expander, a heavy-water-cooled lead spallation neutron source assembly surrounded by light-water-cooled Li-Al blankets, a target window, heat removal systems, and related safety systems. The preconceptual design of each of these major components is described. Descriptions are also provided for the target fabrication, tritium extraction, and waste-steam processes. Performance characteristics are presented and discussed

Topical report on a preconceptual design for the Spallation-Induced Lithium Conversion (SILC) target for the accelerator production of tritium (APT)

Energy Technology Data Exchange (ETDEWEB)

Van Tuyle, G.J.; Cokinos, D.M.; Czajkowski, C.; Franz, E.M.; Kroeger, P.; Todosow, M.; Youngblood, R.; Zucker, M.

1993-09-30

The preconceptual design of the APT Li-Al target system, also referred to as the Spallation-Induced Lithium Conversion (SILC), target system, is summarized in this report. The system has been designed to produce a ``3/8 Goal`` quantity of tritium using the 200-mA, 1.0 GeV proton beam emerging from the LANL-designed LINAC. The SILC target system consists of a beam expander, a heavy-water-cooled lead spallation neutron source assembly surrounded by light-water-cooled Li-Al blankets, a target window, heat removal systems, and related safety systems. The preconceptual design of each of these major components is described. Descriptions are also provided for the target fabrication, tritium extraction, and waste-steam processes. Performance characteristics are presented and discussed.

Tritium transport in HCLL and WCLL DEMO blankets

Energy Technology Data Exchange (ETDEWEB)

Candido, Luigi [DENERG, Politecnico di Torino, Corso Duca degli Abruzzi 24, 10129 Torino (Italy); Utili, Marco [ENEA UTIS- C.R. Brasimone, Bacino del Brasimone, Camugnano, BO (Italy); Nicolotti, Iuri [DENERG, Politecnico di Torino, Corso Duca degli Abruzzi 24, 10129 Torino (Italy); Zucchetti, Massimo, E-mail: massimo.zucchetti@polito.it [DENERG, Politecnico di Torino, Corso Duca degli Abruzzi 24, 10129 Torino (Italy)

2016-11-01

Highlights: • Tritium inventories and tritium losses are the main output of the presented model for HCLL and WCLL. • A parametric study has been performed, to show the behavior of the two systems when certain parameters are changed, in order to minimize inventories and/or losses. • An improved design is needed, in order to reduce the radiological hazard related to tritium activity. According to test number 7, HCLL-BB could be able to have a tritium inventory of 33.05 g and losses of 19.55 Ci/d. • WCLL-BB shows a very low radiological risk, much lower than that suggested (inventory: 17.48 g, losses: 3.2 Ci/d). An ptimization study has been performed aiming to minimize the water flow rate for an upgraded design. • Both for HCLL and WCLL, the most critical parameters able to produce relevant variations in inventories and losses are the helium/water fraction, the CPS/WDS and the permeation reduction factors. - Abstract: The Helium-Cooled Lithium Lead (HCLL) and Water-Cooled Lithium Lead (WCLL) Breeding Blankets are two of the four blanket designs proposed for DEMO reactor. The study of tritium transport inside the blankets is fundamental to assess their preliminary design and safety features. A mathematical model has been derived, in a new form making makes easier to determine the most critical components as far as tritium losses and tritium inventories are concerned, and to model the tritium performance of the whole system. Two cases have been studied, the former with tritium generation rate constant in time and the latter considering a typical pulsed operation for a time span of 100 h. Tritium inventories and tritium losses are the main output of the model. Tritium concentrations, inventories and losses are initially calculated and compared for the two blankets, in a reference case without permeation barriers or cold traps. A parametric study to show the behavior of the two systems when certain parameters are changed, in order to minimize inventories and

Recovery and recycling of lithium value from spent lithium titanate (Li{sub 2}TiO{sub 3}) pebbles

Energy Technology Data Exchange (ETDEWEB)

Mandal, D., E-mail: dmandal10@gmail.com

2013-09-15

Graphical abstract: Effects of various process parameters on the recovery of Li-from spent Li{sub 2}TiO{sub 3} pebbles were investigated. From the experimental results it was observed that the leaching rate increases with speed of stirring till 450 rpm and then above 450 rpm; the increase in speed of stirring does not have any significant effect on the leaching rate as shown in the following figure. Effects of other parameters on the Li-recovery from spent Li{sub 2}TiO{sub 3} pebbles are discussed in this paper. Abstract: In the first generation fusion reactors the fusion of deuterium (D) and tritium (T) is considered to produce energy to meet the future energy demand. Deuterium is available in nature whereas, tritium is not. Lithium-6 (Li{sup 6}) isotope has the ability to produce tritium in the n, α nuclear reaction with neutrons. Thus lithium-based ceramics enriched by Li{sup 6} isotope are considered for the tritium generation for its use in future fusion reactors. Lithium titanate is one such Li-based ceramic material being considered for its some attractive properties viz., high thermal and chemical stability, high thermal conductivity, and low tritium solubility. It is reported in the literature, that the burn up of these pebbles in the fusion reactor will be limited to only 15–17 atomic percentage. At the end of life, the pebbles will contain more than 45% unused Li{sup 6} isotope. Due to the high cost of enriched Li{sup 6} and the waste disposal considerations, it is necessary to recover the unused Li from the spent lithium titanate pebbles. Till date, only the feasibilities of different processes are reported, but no process details are available. Experiments were carried out for the recovery of Li from simulated Li{sub 2}TiO{sub 3} pebbles and to reuse of lithium in lithium titanate pebble fabrication. The details of the experiments and results are discussed in this paper.

A low-risk aqueous lithium salt blanket for engineering test reactors

International Nuclear Information System (INIS)

Gierszewski, P.

1986-09-01

A simple blanket concept is proposed based on 1-3 wt.% lithium dissolved as a salt in low temperature (80 degrees C) and low pressure (0.1 MPa) water. This concept can provide, for example, a 0.5 tritium breeding ratio with 60% steel structure and 70% coverage. The use of neutron multipliers, other structural materials (especially zirconium alloys), higher coverage and higher lithium salt concentrations allows tritium breeding ratios over unity if necessary. Other advantages of this concept include the simple shield-like geometry, substantial structural volume for mechanical strength, excellent heat transfer ability of water coolant, efficient neutron and gamma shielding through the combination of high-Z structure and low-Z water, and conventional tritium recovery and control technology. This concept could initially provide the shielding needs for an engineering test reactor and later, by the addition of lithium salt and tritium recovery systems, also provide tritium breeding. This staged operation and liquid breeder/coolant allows control over the tritium inventory in the device without machine disassembly. 14 refs

Does 8-methacryloxyoctyl trimethoxy silane (8-MOTS) improve initial bond strength on lithium disilicate glass ceramic?

Science.gov (United States)

Maruo, Yukinori; Nishigawa, Goro; Yoshihara, Kumiko; Minagi, Shogo; Matsumoto, Takuya; Irie, Masao

2017-03-01

Dental ceramic surfaces are modified with silane coupling agents, such as γ-methacryloxypropyl trimethoxy silane (γ-MPTS), to improve bond strength. For bonding between lithium disilicate glass ceramic and resin cement, the objective was to investigate if 8-methacryloxyoctyl trimethoxy silane (8-MOTS) could yield a similar performance as the widely used γ-MPTS. One hundred and ten lithium disilicate glass ceramic specimens were randomly divided into 11 groups (n=10) according to pretreatment regime. All specimens were pretreated with a different solution composed of one or a combination of these agents: 10 or 20wt% silane coupling agent of γ-MPTS or 8-MOTS, followed by a hydrolysis solution of acetic acid or 10-methacryloyloxydecyl dihydrogen phosphate (10-MDP). Each pretreated surface was luted to a stainless steel rod of 3.6mm diameter and 2.0mm height with resin cement. Shear bond strength between ceramic and cement was measured after 24-h storage in 37°C distilled water. 8-MOTS produced the same bonding performance as γ-MPTS. Both silane coupling agents significantly increased the bond strength of resin cement, depending on their concentration. When activated by 10-MDP hydrolysis solution, 20wt% concentration produced the highest values (γ-MPTS: 24.9±5.1MPa; 8-MOTS: 24.6±7.4MPa). Hydrolysis with acetic acid produced lower bond strengths than with 10-MDP. Silane coupling pretreatment with 8-MOTS increased the initial bond strength between lithium disilicate glass ceramic and resin cement, rendering the same bonding effect as the conventional γ-MPTS. Copyright © 2016 The Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

The TFTR lithium blanket module program

International Nuclear Information System (INIS)

Jassby, D.L.; Bertone, P.C.; Creedon, R.L.; File, J.; Graumann, D.W.

1985-01-01

The Lithium Blanket Module (LBM) is an approximately 80X80X80 cm cubic module, representative of a helium-cooled lithium oxide fusion reactor blanket module, that will be installed on the TFTR (Tokamak Fusion Test Reactor) in late 1986. The principal objective of the LBM Program is to perform a series of neutron transport and tritium-breeding measurements throughout the LBM when it is exposed to the TFTR toroidal fusion neutron source, and to compare these data with the predictions of Monte Carlo (MCNP) neutronics codes. The LBM consists of 920 2.5-cm diameter breeder rods constructed of lithium oxide (Li 2 O) pellets housed in thin-walled stainless steel tubes. Procedures for mass-producing 25,000 Li 2 O pellets with satisfactory reproducibility were developed using purified Li 2 O powder, and fabrication of all the breeder rods was completed in early 1985. Tritium assay methods were investigated experimentally using both small lithium metal samples and LBM-type pellets. This work demonstrated that the thermal extraction method will be satisfactory for accurate evaluation of the minute concentrations of tritium expected in the LBM pellets (0.1-1nCi/g)

Neutronics Evaluation of Lithium-Based Ternary Alloys in IFE Blankets

Energy Technology Data Exchange (ETDEWEB)

Jolodosky, A. [Univ. of California, Berkeley, CA (United States); Fratoni, M. [Univ. of California, Berkeley, CA (United States)

2015-09-22

Lithium is often the preferred choice as breeder and coolant in fusion blankets as it offers excellent heat transfer and corrosion properties, and most importantly, it has a very high tritium solubility and results in very low levels of tritium permeation throughout the facility infrastructure. However, lithium metal vigorously reacts with air and water and exacerbates plant safety concerns. For this reason, over the years numerous blanket concepts have been proposed with the scope of reducing concerns associated with lithium. The European helium cooled pebble bed breeding blanket (HCPB) physically confines lithium within ceramic pebbles. The pebbles reside within a low activation martensitic ferritic steel structure and are cooled by helium. The blanket is composed of the tritium breeding lithium ceramic pebbles and neutron multiplying beryllium pebbles. Other blanket designs utilize lead to lower chemical reactivity; LiPb alone can serve as a breeder, coolant, neutron multiplier, and tritium carrier. Blankets employing LiPb coolants alongside silicon carbide structural components can achieve high plant efficiency, low afterheat, and low operation pressures. This alloy can also be used alongside of helium such as in the dual-coolant lead-lithium concept (DCLL); helium is utilized to cool the first wall and structural components made up of low-activation ferritic steel, whereas lithium-lead (LiPb) acts as a self-cooled breeder in the inner channels of the blanket. The helium-cooled steel and lead-lithium alloy are separated by flow channel inserts (usually made out of silicon carbide) which thermally insulate the self-cooled breeder region from the helium cooled steel walls. This creates a LiPb breeder with a much higher exit temperature than the steel which increases the power cycle efficiency and also lowers the magnetohydrodynamic (MHD) pressure drop [6]. Molten salt blankets with a mixture of lithium, beryllium, and fluorides (FLiBe) offer good tritium breeding

Irradiation effects on the tumor and adjacent tissues of brain tumor-bearing mice

International Nuclear Information System (INIS)

Yoshii, Yoshihiko; Maki, Yutaka; Tsunemoto, Hiroshi; Koike, Sachiko; Furukawa, Shigeo.

1979-01-01

C 3 H mice aged 56 - 70 days, weighing 27 - 37 g were used throughout this experiment. A transplantable fibrosarcoma arising spontaneously from C 3 H mice was used. For experiment, 10 4 tumor cells suspended in 0.025 ml of saline solution were injected into the cerebral hemisphere by a 26 gauge needle with a micrometer syringe under nembutal anesthesia. Whole brain irradiation was performed at 7 days after injection of the tumor cells and the radiation doses were 2,000 and 20,000 rads, respectively. The feature of x-rays were 200 kVp, 20 mA, 0.5 mm Cu + 0.5 mm Al filtration and TSD 20 cm. The dose-rate was 340 - 360 R/min. The articles of this study were as follows: a) Determination of LD 50 values for the mice, tumor-bearing in the brain or non-tumor-bearing; and b) Observation of clinical features and gross autopsy findings of the mice following irradiation. The LD 50 values for 2,000 rad irradiation in the tumor-bearing or non-tumor-bearing mice were 10.9 and 11.4 days, respectively. LD 50 values of 3.7 days and 4.3 days were the results for the tumor-bearing and non-tumor-bearing mice irradiated by 20,000 rad, respectively. On the other hand, the LD 50 value for the control group, i.e. non-irradiated mice, was 6.7 days. At postmortem examinations, gastrointestinal bleeding was observed frequently in mice bearing tumor in the brain. Whole brain irradiation is effective to prolong the life of tumor-bearing mice. However, in some instances, deaths have occurred earlier in tumor-bearing mice compared to the control group. (author)

Experiments on tritium behavior in beryllium, (2)

International Nuclear Information System (INIS)

Ishitsuka, Etsuo; Kawamura, Hiroshi; Nakata, Hirokatsu; Sugai, Hiroyuki; Tanase, Masakazu.

1990-02-01

Beryllium has been used as the neutron reflector of material testing reactor and as the neutron multiplier for the fusion reactor lately. To study the tritium behavior in beryllium, we conducted the experiments, i.e., tritium release by recoil or diffusion by using the hot-pressed beryllium which had been produced both tritium and helium by neutron irradiation. From our experiments, we found that (1) amount of tritium production per one cycle irradiation (lasting 22 days) of JMTR is 10 mCi/g, (2) amount of tritium per surface area of hot-pressed beryllium released by recoil is 4 μCi/cm 2 , (3) diffusion coefficient of tritium in a temperature range of 800 ∼1180degC can be expressed with the following equation; D = 8.7 x 10 4 exp(-2.9x10 5 /R/T) cm 2 /s. (author)

Lithium-stimulated recovery of granulopoiesis after sublethal irradiation is not mediated via increased levels of colony stimulating factor (CSF)

International Nuclear Information System (INIS)

Gallicchio, V.S.; Chen, M.G.; Watts, T.D.

1985-01-01

Lithium accelerates the recovery of granulopoiesis following sublethal (2 Gy) whole body x-irradiation. Studies are described that further define this Li-mediated recovery by measuring the levels of colony-stimulating factor (CSF) present in serum from mice administered 105 μg/mouse (total dose) of ultra-pure Li 2 CO 3 for 3 days following irradiation. On days 1-28 following the last lithium dose, the serum was tested for its CSF activity against both normal non-adherent derived bone marrow target cells and non-adherent marrow cells from mice administered cyclophosphamide (200 mg/kg body weight). Serum was assayed at 0.01, 0.1, 1 and 10% final concentration. No significant difference in the total number of CFU-GM was observed from normal marrow using either serum from irradiated mice or lithium-treated and irradiated mice, although the irradiation did produce a 300% rise in CFU-GM colonies compared to normal serum (days 4 and 10-15). From regenerating marrow, a significant difference (P <= 0.01) was observed in CFU-GM cultured with serum at 0.1% concentration from irradiated and lithium-treated mice compared to irradiated mice without lithium. The presence of CSF was confirmed by its reduced activity in the presence of anti-(CSF). (U.K.)

Tritium containment of controlled thermonuclear fusion reactor

International Nuclear Information System (INIS)

Tanaka, Yoshihisa; Tsukumo, Kiyohiko; Suzuki, Tatsushi

1979-01-01

It is well known that tritium is used as the fuel for nuclear fusion reactors. The neutrons produced by the nuclear fusion reaction of deuterium and tritium react with lithium in blankets, and tritium is produced. The blankets reproduce the tritium consumed in the D-T reaction. Tritium circulates through the main cooling system and the fuel supply and evacuation system, and is accumulated. Tritium is a radioactive substance emitting β-ray with 12.6 year half-life, and harmful to human bodies. It is an isotope of hydrogen, and apt to diffuse and leak. Especially at high temperature, it permeates through materials, therefore it is important to evaluate the release of tritium into environment, to treat leaked tritium to reduce its release, and to select the method of containing tritium. The permeability of tritium and its solubility in structural materials are discussed. The typical blanket-cooling systems of nuclear fusion reactors are shown, and the tungsten coating of steam generator tubes and tritium recovery system are adopted for reducing tritium leak. In case of the Tokamak type reactor of JAERI, the tritium recovery system is installed, in which the tritium gas produced in blankets is converted to tritium steam with a Pd-Pt catalytic oxidation tower, and it is dehydrated and eliminated with a molecular sieve tower, then purified and recovered. (Kako, I.)

Plasma wall interaction and tritium retention in TFTR

International Nuclear Information System (INIS)

Skinner, C.H.; Amarescu, E.; Ascione, G.

1996-01-01

The Tokamak Fusion Test Reactor (TFTR) has been operating safely and routinely with deuterium-tritium fuel for more than two years. In this time, TFTR has produced an impressive number of record breaking results including core fusion power, ∼ 2 MW/m 3 , comparable to that expected for ITER. Advances in wall conditioning via lithium pellet injection have played an essential role in achieving these results. Deuterium-tritium operation has also provided a special opportunity to address the issues of tritium recycling and retention. Tritium retention over two years of operation was approximately 40%. Recently, the in-torus tritium inventory was reduced by half through a combination of glow discharge cleaning, moist-air soaks, and plasma discharge cleaning. The tritium inventory is not a constraint in continued operations. The authors present recent results from TFTR in the context of plasma wall interactions and deuterium-tritium issues

Plasma wall interaction and tritium retention in TFTR

International Nuclear Information System (INIS)

Skinner, C.H.; Amarescu, E.; Ascione, G.

1997-01-01

The Tokamak Fusion Test Reactor (TFTR) has been operating safely and routinely with deuterium-tritium fuel for more than two years. In this time, TFTR has produced a number of record breaking results including core fusion power, ∝2 MW/m 3 , comparable to that expected for ITER. Advances in wall conditioning via lithium pellet injection have played an essential role in achieving these results. Deuterium-tritium operation has also provided a special opportunity to address the issues of tritium recycling and retention. Tritium retention over two years of operation was approximately 40%. Recently the in-torus tritium inventory was reduced by half through a combination of glow discharge cleaning, moist-air soaks, and plasma discharge cleaning. The tritium inventory is not a constraint in continued operations. Recent results from TFTR in the context of plasma wall interactions and deuterium-tritium issues are presented. (orig.)

A study on structure defects in irradiated lithium fluoride (thermal neutrons); Etude des imperfections de structure du fluorure de lithium irradie (neutrons thermiques)

Energy Technology Data Exchange (ETDEWEB)

Lambert, M

1958-06-19

A study was made of the behavior of atomic defects, vacancies and interstitials, generated from the Li{sup 6}(n,{alpha})H{sup 3} reaction in Lip crystals. Defects appear as cavities and platelets around ten angstrom in size and increase both with neutron dose and annealing temperature. For longer irradiations, metallic lithium precipitates out, in epitaxy with LiF lattice, and later, lithium salts appear due to the penetration of atmospheric gases through the cracks present in the damaged crystal. Various x-ray experiments followed the formation and evolution of these imperfections when their atomic concentration reached 10{sup -4}. (author)

Nitrogen Recovery by Fe-Ti Alloy from Molten Lithium at High Temperatures

International Nuclear Information System (INIS)

Juro Yagi; Akihiro Suzuki; Takayuki Terai; Takeo Muroga

2006-01-01

Molten lithium will be used as a beam target of IFMIF (International Fusion Materials Irradiation Facility), and is also expected as a self-cooling and tritium breeding material in fusion reactors. Since tritium is generated in both cases, tritium recovery is required from viewpoints of safety and a feasible fuel cycle. Nitrogen impurity in the lithium, however, not only enhance corrosion to tubing materials, but also promote nitride contamination on a surface of yttrium, which is considered to be a tritium gettering candidate. In our previous study, nitrogen recovery by hot trap method with Fe + 5%Ti alloy as a gettering material showed a higher nitrogen reduction capacity than that with Ti or Cr metal. In this study, high temperature recovery of nitrogen with Fe-Ti alloy was examined to achieve more efficient recovery and higher recovery rate coefficient. Fe - 4%Ti alloy are fabricated by electron beam melting, and its thin plates (40 mm x 10 mm x 1 mm) are used in our experiments. The Fe - 4%Ti alloy plates were immersed into 25 g of liquid lithium in Mo crucible under Ar atmosphere. The crucible was put in a SUS316 stainless steel pot heated at 600, 700, or 800 o C up to 100 hours. A small portion of the liquid lithium in the crucible was sampled out with adequate time interval, and the nitrogen concentrations in the sampled lithium were observed by changing nitrogen to ammonia. Experiments using lithium containing about 100 wt. ppm of nitrogen at the beginning show that the nitrogen reduction became faster with temperature and the minimum achieved nitrogen concentration was less than 20 wppm in case of 800 C. SEM-EDS analysis on the plates after experiment shows a Ti-rich surface layer of tens of micrometers on the alloy immersed in lithium at 800 C, and XPS analysis indicates the surface layer is TiN, while no Ti-rich layer nor TiN were observed on the alloys immersed at 600 o C and 700 o C. By increasing temperature from 600 o C to 800 o C, the diffusion

UV irradiation improves the bond strength of resin cement to fiber posts.

Science.gov (United States)

Zhong, Bo; Zhang, Yong; Zhou, Jianfeng; Chen, Li; Li, Deli; Tan, Jianguo

2011-01-01

The purpose is to evaluate the effect of UV irradiation on the bond strength between epoxy-based glass fiber posts and resin cement. Twelve epoxy-based glass fiber posts were randomly divided into three groups. Group 1 (Cont.): No surface treatment. Group 2 (Low-UV): UV irradiation was conducted from a distance of 10 cm for 10 min. Group 3 (High-UV): UV irradiation was conducted from a distance of 1 cm for 3 min. A resin cement (CLEARFIL SA LUTING) was used for the post cementation to form resin slabs which contained fiber posts in the center. Microtensile bond strengths were tested and the mean bond strengths (MPa) were 18.81 for Cont. group, 23.65 for Low-UV group, 34.75 for High-UV group. UV irradiation had a significant effect on the bond strength (pUV irradiation demonstrates its capability to improve the bond strength between epoxy-based glass fiber posts and resin cement.

Shear bond strength of resin composite bonded with two adhesives: Influence of Er: YAG laser irradiation distance

Science.gov (United States)

Shirani, Farzaneh; Birang, Reza; Malekipour, Mohammad Reza; Hourmehr, Zahra; Kazemi, Shantia

2014-01-01

Background: Dental surfaces prepared with different Er:YAG laser distance may have different characteristics compared with those prepared with conventional instruments. The aim of this study was to investigate the effect of Er:YAG laser irradiation distance from enamel and dentin surfaces on the shear bond strength of composite with self-etch and etch and rinse bonding systems compared with conventional preparation method. Materials and Methods: Two hundred caries-free human third molars were randomly divided into twenty groups (n = 10). Ten groups were designated for enamel surface (E1-E10) and ten for dentin surface (D1-D10). Er: YAG laser (2940 nm) was used on the E1-E8 (240 mJ, 25 Hz) and D1-D8 (140 mJ, 30 Hz) groups at four different distances of 0.5 (standard), 2, 4 and 11 mm. Control groups (E9, E10, D9 and D10) were ground with medium grit diamond bur. The enamel and dentin specimens were divided into two subgroups that were bonded with either Single Bond or Clearfil SE Bond. Resin composite (Z100) was dispensed on prepared dentin and enamel. The shear bond strengths were tested using a universal testing machine. Data were analyzed by SPSS12 statistical software using three way analysis of variance, Tukey and independent t-test. P enamel and dentin substrates (P enamel surfaces (in both bonding agent subgroups) and on dentin surfaces (in the Single Bond subgroup). Conclusion: Laser irradiation decreases shear bond strength. Irradiation distance affects shear bond strength and increasing the distance would decrease the negative effects of laser irradiation. PMID:25540665

Long Term Tritium Trapping in TFTR and JET

International Nuclear Information System (INIS)

Skinner, C.H.; Gentile, C.A.; Young, K.M.; Coad, J.P.; Hogan, J.T.; Penzhorn, R.-D.; Bekris, N.

2001-01-01

Tritium retention in TFTR [Tokamak Fusion Test Reactor] and JET [Joint European Torus] shows striking similarities and contrasts. In TFTR, 5 g of tritium were injected into circular plasmas over a 3.5 year period, mostly by neutral-beam injection. In JET, 35 g were injected into divertor plasmas over a 6 month campaign, mostly by gas puffing. In TFTR, the bumper limiter provided a large source of eroded carbon and a major part of tritium was co-deposited on the limiter and vessel wall. Only a small area of the co-deposit flaked off. In JET, the wall is a net erosion area, and co-deposition occurs principally in shadowed parts of the inner divertor, with heavy flaking. In both machines, the initial tritium retention, after a change from deuterium [D] to tritium [T] gas puffing, is high and is due to isotope exchange with deuterium on plasma-facing surfaces (dynamic inventory). The contribution of co-deposition is lower but cumulative, and is revealed by including periods of D fueling that reversed the T/D isotope exchange. Ion beam analysis of flakes from TFTR showed an atomic D/C ratio of 0.13 on the plasma facing surface, 0.25 on the back surface and 0.11 in the bulk. Data from a JET divertor tile showed a larger D/C ratio with 46% C, 30% D, 20% H and 4% O. Deuterium, tritium, and beryllium profiles have been measured and show a thin less than 50 micron co-deposited layer. Flakes retrieved from the JET vacuum vessel exhibited a high tritium release rate of 2e10 Bq/month/g. BBQ modeling of the effect of lithium on retention in TFTR showed overlapping lithium and tritium implantation and a 1.3x increase in local T retention

Tritium control and capture in salt-cooled fission and fusion reactors: Status, challenges, and path forward

International Nuclear Information System (INIS)

Forsberg, Charles W.; Lam, Stephen; Carpenter, David M.; Whyte, Dennis G.; Scarlat, Raluca

2017-01-01

Three advanced nuclear power systems use liquid salt coolants that generate tritium and thus face the common challenges of containing and capturing tritium to prevent its release to the environment. The Fluoride-salt-cooled High-temperature Reactor (FHR) uses clean fluoride salt coolants and the same graphite-matrix coated-particle fuel as high-temperature gas-cooled reactors. Molten salt reactors (MSRs) dissolve the fuel in a fluoride or chloride salt with release of fission product tritium into the salt. In most FHR and MSR systems, the base-line salts contain lithium where isotopically separated "7Li is proposed to minimize tritium production from neutron interactions with the salt. The Chinese Academy of Science plans to start operation of a 2-MWt molten salt test reactor by 2020. For high-magnetic-field fusion machines, the use of lithium enriched in "6Li is proposed to maximize tritium generation the fuel for a fusion machine. Advances in superconductors that enable higher power densities may require the use of molten lithium salts for fusion blankets and as coolants. Recent technical advances in these three reactor classes have resulted in increased government and private interest and the beginning of a coordinated effort to address the tritium control challenges in 700 °C liquid salt systems. We describe characteristics of salt-cooled fission and fusion machines, the basis for growing interest in these technologies, tritium generation in molten salts, the environment for tritium capture, models for high-temperature tritium transport in salt systems, alternative strategies for tritium control, and ongoing experimental work. Several methods to control tritium appear viable. Finally, limited experimental data is the primary constraint for designing efficient cost-effective methods of tritium control.

Quantitative detection of microscopic lithium distributions with neutrons

Energy Technology Data Exchange (ETDEWEB)

Neri, Giulia; Gernhaeuser, Roman; Lichtinger, Josef; Winkler, Sonja; Seiler, Dominik; Bendel, Michael [Technische Universitaet Muenchen, Physik-Department (Germany); Kunze-Liebhaeuser, Julia; Brumbarov, Jassen; Portenkirchner, Engelbert [Institut fuer Physikalische Chemie, Leopold-Franzens-Universitaet Innsbruck (Austria); Renno, Axel; Rugel, Georg [Helmholtz Zentrum Dresden Rossendorf, Helmholtz-Institut Freiberg fuer Ressourcentechnologie (Germany)

2016-07-01

The importance of lithium in the modern industrial society is continuously increasing. Spatially resolved detection of tritium particles from {sup 6}Li(n,α){sup 3}H nuclear reactions is used to reconstruct microscopic lithium distributions. Samples are exposed to a flux of cold neutrons. Emitted charged particles are detected with a PSD. Introducing a pinhole aperture between target and detector, the experimental setup works like a ''camera obscura'', allowing to perform spatially resolved measurements. Tritium detection analysis was successfully used to reconstruct the lithium content in self-organized TiO{sub 2-x}-C and Si/TiO{sub 2-x}-C nanotubes electrochemically lithiated, for the first time. Titanium dioxide nanotubes are a candidate for a safe anode material in lithium-ion batteries. Also lithium distributions in geological samples, so called ''pathfinder-minerals'' containing lithium, like lepidolite from a pegmatite, were analyzed. With this development we present a new precision method using nuclear physics for material science.

Evaluation of the response time of H-concentration probes for tritium sensors in lead–lithium eutectic alloy

Energy Technology Data Exchange (ETDEWEB)

Llivina, L.; Colominas, S.; Abellà, J., E-mail: jordi.abella@iqs.edu

2014-10-15

Highlights: • Synthesis and chemical characterization of proton conductor ceramics. • Qualification of ceramics for hydrogen sensors in molten lithium–lead. • Ceramics have well-defined grains with a wide distribution of sizes. • Good agreement with predictions obtained with BaCe{sub 0.6}Zr{sub 0.3}Y{sub 0.1}O{sub 3−δ} ceramic. - Abstract: Dynamic tritium concentration measurement in lead–lithium eutectic is of major interest for a reliable tritium testing program in ITER TBM and for an experimental proof of tritium self-sufficiency in liquid metal breeding systems. Potentiometric hydrogen sensors using different solid-state electrolytes for molten lead–lithium eutectic have been reported and tested by the Electrochemical Methods Lab at Institut Quimic de Sarria (IQS). In the present work the following ceramic elements have been synthesized and characterized by X-ray diffraction (XRD) in order to be tested as a Proton Exchange Membranes (PEM) H-probes: BaCeO{sub 3}, BaCe{sub 0.6}Zr{sub 0.3}Y{sub 0.1}O{sub 3−δ} and Sr(Ce{sub 0.9}–Zr{sub 0.1}){sub 0.95}Yb{sub 0.05}O{sub 3−δ}. Potentiometric measurements of the synthesized ceramic elements have been performed shifting from a fixed hydrogen partial pressure at the working electrode to high purity argon. In this experimental campaign a fixed and known hydrogen pressure has been used in the reference electrode. The goal of these experiments is to evaluate the sensor response time when the hydrogen concentration in the environment is rapidly changed. All experiments have been done at 500 °C and 600 °C. The sensor constructed using the proton conductor element BaCe{sub 0.6}Zr{sub 0.3}Y{sub 0.1}O{sub 3−δ} exhibited stable output potential and its value was close to the theoretical value calculated with the Nernst equation. In contrast, the sensors constructed using the proton conductor elements BaCeO{sub 3} and Sr(Ce{sub 0.9}–Zr{sub 0.1}){sub 0.95}Yb{sub 0.05}O{sub 3−δ} showed higher

EXOTIC: Development of ceramic tritium breeding materials

International Nuclear Information System (INIS)

Kwast, H.; Conrad, R.

1989-09-01

In this fifth EXOTIC annual progress report the work carried out in 1988 is reported. For EXOTIC-1, -2 and -3 the post-irradiation examinations have been continued with tritium retention measurements, annealng experiments, determination of physical and mechanical properties and X-ray diffraction analysis. Irradiation of EXOTIC-4 has been performde and the post-irradiation examination has started. Transient tritium release curves are given and analysed. The resulting tritium residence times show that for the Li-zirconates a residence time of less than one day can be achieved in the temperature region of 350-600 C. The loading scheme, the objectives and some fabrication data of EXOTIC-5 are give. Moreover, the fabrication of laboratory scale batches has started to investigate the effect of microstructural parameters on tritium release. Finally, an investigation was started on the system Li 2 O-ZrO 2 , with emphasis on the lithia-rich compositions. 40 figs., 9 refs., 10 tabs

Progress report on the accelerator production of tritium materials irradiation program

International Nuclear Information System (INIS)

Maloy, S.A.; Sommer, W.F.; Brown, R.D.; Roberts, J.E.

1997-01-01

The Accelerator Production of Tritium (APT) project is developing an accelerator and a spoliation neutron source capable of producing tritium through neutron capture on He-3. A high atomic weight target is used to produce neutrons that are then multiplied and moderated in a blanket prior to capture. Materials used in the target and blanket region of an APT facility will be subjected to several different and mixed particle radiation environments; high energy protons (1-2 GeV), protons in the 20 MeV range, high energy neutrons, and low energy neutrons, depending on position in the target and blanket. Flux levels exceed 10 14 /cm 2 s in some areas. The APT project is sponsoring an irradiation damage effects program that will generate the first data-base for materials exposed to high energy particles typical of spallation neutron sources. The program includes a number of candidate materials in small specimen and model component form and uses the Los Alamos Spallation Radiation Effects Facility (LASREF) at the 800 MeV, Los Alamos Neutron Science Center (LANSCE) accelerator

On the possibility of using lithium-6 deuteride, irradiated with gas discharge plasma in a target with polarized nuclei of deuterium and lithium

International Nuclear Information System (INIS)

Bunyatova, E.I.; Bubnov, N.N.; Solodovnikov, S.P.

1991-01-01

A target with polarized nuclei made on the basis of irradiated lithium-6 deuteride is of great interest for carrying out investigations in elementary particle physics. Up to now high-energy electrons have been used for generation of F-centers in 6 LiD. It is shown that one can, in principle, use ultraviolet irradiation and gas discharge plasma for generation of F-centers in 6 LiD. Both types of irradiation cause electron paramagnetic resonance signals from conductance electrons of lithium and form F-centers in 6 LiD. It seems possible to obtain the necessary samples by exposing 6 LiD to the gas discharge plasma. 9 refs.; 2 figs

Tritium transfer studies in cellulose-HTO system

International Nuclear Information System (INIS)

Jayaraman, A.P.; Misra, B.M.

1986-01-01

This paper describes some aspects of studies on transfer of tritium to cellulose from tritiated water at six different specific activities and discusses the generalized tritiation pattern. Cellulose was irradiated in steps to 10 M Rads and the tritium transfer was determined at each stage. Experimental results signify substantial increase of tritiation in cellulose at higher dose of irradiation. (author). 8 refs

Radiation damage and defect behavior in proton irradiated lithium-counterdoped n/sup +/p silicon solar cells

International Nuclear Information System (INIS)

Stupica, J.; Goradia, C.; Swartz, C.K.; Weinberg, I.

1987-01-01

Two lithium-counterdoped n/sup +/p silicon solar cells with different lithium concentrations were irradiated by 10 MeV protons. Cell performance was measured as a function of fluence, and it was found that the cell with the highest concentration of lithium had the higher radiation resistance. Deep level defects were studied using deep level transient spectroscopy which yielded two defects that were lithium related. Relating the defect energy levels obtained from this study under 10 MeV protons, with an earlier work using 1 MeV electron irradiations shows no correlation of the defect energy levels. There is one marked comparison though. The absence of the boron interstitial-oxygen interstitial defect. This consistency strengthens the belief that lithium interacts with oxygen to prevent the formation of the boron interstitial-oxygen interstitial defect. The present results indicate that, in general, addition of lithium in small amounts to the p-base of a boron doped silicon solar cell such that the base remains p-type, tends to increase the radiation resistance of the cell

Loss of Ia-bearing splenic adherent cells after whole body ultraviolet irradiation

International Nuclear Information System (INIS)

Letvin, N.L.; Nepom, J.T.; Greene, M.I.; Benacerraf, B.; Germain, R.N.

1980-01-01

Daily uv irradiation of mice results in a marked decrease in the antigen-presenting capability of SAC from these mice after 1 wk of uv exposure. To directly examine this cell population, we developed a technique for purifying SAC that involves passing mouse splenocytes through two cycles of glass adherence with an intervening incubation on rabbit anti-mouse Ig-coated dishes. SAC from externally uv irradiated mice prepared by this method, when pulsed with antigen, activate primed T cells to proliferate much less efficiently than SAC from normal mice. Both the proportion and absolute number of Ia-bearing cells in this purified SAC population from uv irradiated mice are considerably smaller than that seen in similarly prepared populations from normal mice. Previous adjuvant immunization was shown to override functional defects elicited by external uv irradiation. This demonstration of a uv irradiation induced selective loss of Ia bearing splenic adherent cells and the functional consequences of this loss provide further evidence for the importance of Ia-bearing accessory cells in antigen presentation of T dependent antigens, and provides insight into the origin of the immunologic defects induced by whole body uv irradiation

Density of trapped gas in heavily-irradiated lithium hydride

International Nuclear Information System (INIS)

Bowman, R.C. Jr.; Attalla, A.; Souers, P.C.; Folkers, C.L.; McCreary, T.; Snider, G.D.; Vanderhoofven, F.; Tsugawa, R.T.

1988-01-01

We review old gamma-irradiated lithium hydride data and also display much new bulk and gas-displacement density and nuclear magnetic resonance data on Li(D, T) and LiT at 296 to 373 K. We find that: (1) Li(D, T) swells because of the formation of internal D-T and 3 He gas bubbles, but probably not because of the precipitation of lithium metal; (2) the gas bubbles are at densities of at least 3 to 4x10 4 mol/m 3 , i.e. thousands of atmospheres; (3) outgassing may be largely the result of bubbles rupturing, although diffusion of 3 He as atoms may occur at long times. (orig.)

PDRD (SR13046) TRITIUM PRODUCTION FINAL REPORT

Energy Technology Data Exchange (ETDEWEB)

Smith, P.; Sheetz, S.

2013-09-30

Technical Advisory Committee (TAC) ran a Monte Carlo N-Particle (MCNP) model of a basic SFR for comparison. A 600MWth core surrounded by a lithium blanket produced approximately 1,000 grams of tritium annually with a 13% enriched, 6 year core. This is similar results to a mid-1990’s study where the Fast Flux Test Facility (FFTF), a 400 MWth reactor at the Idaho National Laboratory (INL), could produce about 1,000 grams with an external lithium target. Normalized to the LWRs values, comparative tritium production for an SFR could be approximately 0.31 g-T/kg LEU.

Absolute measurement of the responses of small lithium glass scintillators to gamma radiation

International Nuclear Information System (INIS)

Dalton, A.W.

1987-04-01

The absolute scintillation efficiency and intrinsic resolution of lithium glass scintillators for electron excitation have been determined over a range of electron energies, lithium concentrations and lithium enrichments. Measurements of these response characteristics form part of a study on the possible use of such glasses for the determination of tritium breeding in fusion reactor blanket experiments. The measurements were undertaken to establish a basis for extracting the information relating to tritium production reactions from the background signals induced within the glass scintillators by the neutron/gamma fields of a fusion reactor blanket. Criteria for the selection of glasses most suitable for tritium breeding measurements are discussed in tems of their observed responses

Experiences with decontaminating tritium-handling apparatus

International Nuclear Information System (INIS)

Maienschein, J.L.; Garcia, F.; Garza, R.G.; Kanna, R.L.; Mayhugh, S.R.; Taylor, D.T.

1991-07-01

Tritium-handling apparatus has been decontaminated as part of the shutdown of the LLNL Tritium Facility. Two stainless-steel gloveboxes that had been used to process lithium deuteride-tritide (LiDT) salt were decontaminated using the Portable Cleanup System so that they could be flushed with room air through the facility ventilation system. Further surface decontamination was performed by scrubbing the interior with paper towels and ethyl alcohol or Swish trademark. The surface contamination, as shown by swipe surveys, was reduced from 4x10 4 --10 6 disintegrations per minute (dpm)/cm 2 to 2x10 2 --4x10 4 dpm/cm 2 . Details on the decontamination operation are provided. A series of metal (palladium and vanadium) hydride storage beds have been drained of tritium and flushed with deuterium in order to remove as much tritium as possible. The bed draining and flushing procedure is described, and a calculational method is presented which allows estimation of the tritium remaining in a bed after it has been drained and flushed. Data on specific bed draining and flushing are given

A novel portable system for detecting and measuring tritium

International Nuclear Information System (INIS)

Barillari, Domenico

2007-01-01

A novel tritium detector configuration is described based on the anthracene scintillation method. Tritium-bearing samples are applied to a plate-bearing finely sublimed anthracene crystals and viewed in a field-able PMT-based reader against a standard plate. A microprocessor-based control and signal analysis system delivers a reading with a sensitivity of better than 5 nCi 3 H in approximately 3 min, and 2.3 nCi in 10 min of counting

Electron irradiation effects on lithium peroxide

Science.gov (United States)

Kikkawa, Jun; Shiotsuki, Taishi; Shimo, Yusuke; Koshiya, Shogo; Nagai, Takuro; Nito, Takehiro; Kimoto, Koji

2018-03-01

In this study, electron irradiation effects on lithium peroxide (Li2O2), which is an important discharge product of Li-air (or Li-O2) batteries, were investigated using selected-area electron diffraction (SAED) and high-energy resolution electron energy-loss spectroscopy (EELS). The results obtained show that Li2O2 to Li2O transformation occurs with 80 and 300 keV incident electrons under high electron dose rates at 20 and -183 °C. The Li2O2 to Li2O transformation rate for 300 keV was 1/5 of that for 80 keV with the irradiation taking place at -183 °C. We also present a series of the EELS spectra that can be used as a criterion to judge the molar ratio of Li2O to Li2O2 in the general systems where Li2O2 and Li2O coexist.

Pebble fabrication and tritium release properties of an advanced tritium breeder

Energy Technology Data Exchange (ETDEWEB)

Hoshino, Tsuyoshi, E-mail: hoshino.tsuyoshi@jaea.go.jp [Breeding Functional Materials Development Group, Department of Blanket Systems Research, Rokkasho Fusion Institute, Sector of Fusion Research and Development, Japan Atomic Energy Agency, 2-166 Obuch, Omotedate, Rokkasho-mura, Kamikita-gun, Aomori 039-3212 (Japan); Edao, Yuki [Tritium Technology Group, Department of Blanket Systems Research, Rokkasho Fusion Institute, Sector of Fusion Research and Development, Japan Atomic Energy Agency, 2-4 Shirakata, Shirane, Tokai-mura, Naka-gun, Ibaraki 319-1195 (Japan); Kawamura, Yoshinori [Blanket Technology Group, Department of Blanket Systems Research, Rokkasho Fusion Institute, Sector of Fusion Research and Development, Japan Atomic Energy Agency, 801-1 Mukoyama, Naka, Ibaraki 311-0193 (Japan); Ochiai, Kentaro [BA Project Coordination Group, Department of Fusion Power Systems Research, Rokkasho Fusion Institute, Sector of Fusion Research and Development, Japan Atomic Energy Agency, 2-166 Obuch, Omotedate, Rokkasho-mura, Kamikita-gun, Aomori 039-3212 (Japan)

2016-11-01

Highlights: • Li{sub 2}TiO{sub 3} with excess Li (Li{sub 2+x}TiO{sub 3+y}) pebble as an advanced tritium breeders was fabricated using emulsion method. • Grain size of Li{sub 2+x}TiO{sub 3+y} pebbles was controlled to be less than 5 μm. • Li{sub 2+x}TiO{sub 3+y} pebbles exhibited good tritium release properties similar to that of Li{sub 2}TiO{sub 3} pebbles. - Abstract: Li{sub 2}TiO{sub 3} with excess Li (Li{sub 2+x}TiO{sub 3+y}) has been developed as an advanced tritium breeder. With respect to the tritium release characteristics of the blanket, the optimum grain size after sintering was less than 5 μm. Therefore, an emulsion method was developed to fabricate pebbles with this target grain size. The predominant factor affecting grain growth was assumed to be the presence of binder in the gel particles; this remaining binder was hypothesized to react with the excess Li, thereby generating Li{sub 2}CO{sub 3}, which promotes grain growth. To inhibit the generation of Li{sub 2}CO{sub 3}, calcined Li{sub 2+x}TiO{sub 3+y} pebbles were sintered under vacuum and subsequently under a 1% H{sub 2}–He atmosphere. The average grain size of the sintered Li{sub 2+x}TiO{sub 3+y} pebbles was less than 5 μm. Furthermore, the tritium release properties of Li{sub 2+x}TiO{sub 3+y} pebbles were evaluated, and deuterium–tritium (DT) neutron irradiation experiments were performed at the Fusion Neutronics Source facility in the Japan Atomic Energy Agency. To remove the tritium produced by neutron irradiation, 1% H{sub 2}–He purge gas was passed through the Li{sub 2+x}TiO{sub 3+y} pebbles. The Li{sub 2+x}TiO{sub 3+y} pebbles exhibited good tritium release properties, similar to those of Li{sub 2}TiO{sub 3} pebbles. In particular, the released amount of tritiated hydrogen gas for easier tritium handling was greater than the released amount of tritiated water.

Tritium release from fast neutron irradiated boron carbide

International Nuclear Information System (INIS)

Hollenberg, G.W.

1977-01-01

A high-energy neutron reaction with boron produces tritium. In the LMFBR control material, B 4 C, most of the tritium that is generated remains in the pellets. Potential retention mechanisms are discussed. 5 figures

Development of tritium technology for the United States magnetic fusion energy program

International Nuclear Information System (INIS)

Anderson, J.L.; Wilkes, W.R.

1980-01-01

Tritium technology development for the DOE fusion program is taking place principally at three laboratories, Mound Facility, Argonne National Laboratory and the Los Alamos Scientific Laboratory. This paper will review the major aspects of each of the three programs and look at aspects of the tritium technology being developed at other laboratories within the United States. Facilities and experiments to be discussed include the Tritium Effluent Control Laboratory and the Tritium Storage and Delivery System for the Tokamak Fusion Test Reactor at Mound Facility; the Lithium Processing Test Loop and the solid breeder blanket studies at Argonne; and the Tritium Systems Test Assembly at Los Alamos

The Effect of Lithium Disilicate Ceramic Thickness and Translucency on Shear Bond Strength of Light-cured Resin Cement

Directory of Open Access Journals (Sweden)

Mohammad Javad Moghaddas

2017-09-01

Full Text Available Introduction: To achieve acceptable clinical performance, a ceramic veneer must be bonded to enamel by well-polymerized resin cement. Among different factors, thickness and translucency of the ceramic may affect the resin cement polymerization. Thus, the current study evaluated the effect of the thickness and translucency of lithium disilicate ceramic on light-cured resin cement bond strength to enamel. Methods: In this laboratory study, 208 sound bovine incisors were equally divided into 16 groups (n = 13. The lithium disilicate ceramic cubes in four thicknesses (0.4, 0.6, 0.8 and 1 mm with four translucencies (high and medium opaque, high and low translucent were fabricated and bonded to prepared enamel surfaces using a light-cured translucent resin cement according to manufacturer recommendations. After 5000 cycles of thermocycling, the bonded specimens were placed in a universal testing machine and loaded to the point of fracture. To determine the mode of failure, each sample was observed under a stereomicroscope. Data were recorded and analyzed by Shapiro-Wilk test and two-way analysis of variance (ANOVA. Results: The ceramic thickness and translucency could not significantly affect shear bond strength (SBS of resin cement to enamel (p = 0.17 and p = 0.097, respectively.  The Adhesive and ceramic cohesive failures were reported as the maximum and minimum mode of failure, respectively. Conclusion: The SBS of the light-cured resin cement bonding to enamel and lithium disilicate ceramic was not affected by the translucency of ceramics having a thickness of less than 1 mm.

Decommissioning of a tritium-contaminated laboratory

International Nuclear Information System (INIS)

Harper, J.R.; Garde, R.

1982-01-01

A tritium laboratory facility at the Los Alamos National Laboratory, Los Alamos, New Mexico, was decommissioned in 1979. The project involved dismantling the laboratory equipment and disposing of the equipment and debris at an on-site waste disposal/storage area. The laboratory, constructed in 1953, was in service for tritium research and fabrication of lithium tritide components until 1974. The major features of the laboratory included 25 meters of gloveboxes and hoods, associated vacuum lines, utility lines, exhaust ducts, electrodryers, blowers, and laboratory benches. This report presents details on the decommissioning, health physics, waste management, environmental surveillance, and costs for the operation

New radiobiological findings bearing on the 1977 ICRP recommendations

International Nuclear Information System (INIS)

Dobson, R.L.

1979-01-01

Recent experiments on low-level irradiation during development raise questions relevant to ICRP Publication 26. Mice and monkeys were studied; the measured endpoint was the radiation-induced loss of female germ cells. Three issues are examined. The first is the numerical value of Q (quality factor) appropriate for low-energy beta rays. Comparisons of tritium with gamma radiation were made under conditions of chronic, low-level exposure, and the relative biological effectiveness (RBE) was found to approach 3. Its bearing on ICRP's recommendations concerning Q applicable to tritium is discussed. Second, female germ cells in squirrel monkeys before birth were discovered to be extraordinarily radiosensitive, more easily destroyed than those of mice. If this holds for other primates too, it has radiation-protection implications hitherto overlooked. Third, the contrast between massive germ-cell loss from chronic exposure in prenatal squirrel monkeys and reported radioresistance of oocytes to acute exposure in rhesus monkeys, unless due to species difference, suggests that during development protracted irradiation may be especially injurious. This also could have important radiation-protection implications and is under investigation

Biological effects of tritium

International Nuclear Information System (INIS)

Nieto, M.

1985-01-01

The aim of this project is to study the thermal effects on proliferation activity in the intestinal epithelium of the goldfish acclimated at different temperatures (stationary state). The cell division occurs only at certain phases of the circadian cycle when the proliferative activity is synchronized or trained by an environmental factor such as light-dark cycle. Another aspect of the project is the study of the biological effects, non-stochastic, on cell kinetics in animals chronically exposed to low dose rates or tritium and gamma rays from 60 CO, used as a standard radiation. The influence on the accumulated dose per cell and cycle cell in function of the duration of the cell cycle at different acclimation temperatures should be considered. To calculate the risk of tritium contamination from nuclear power plants (radiation exposure), the organic tissue-bond is of decisive importance due to the long turnover of the organic tissue-bond in organisms favouring transport of tritium to other organisms of the ecosystem and to man. (author)

Chemical form of tritium released from solid breeder materials and the influences of it on a bred tritium recovery systems

International Nuclear Information System (INIS)

Furukubo, Y.; Nishikawa, M.; Nishida, Y.; Kinjyo, T.; Tanifuji, Takaaki; Kawamura, Yoshinori; Enoeda, Mikio

2004-01-01

The ratio of HTO in total tritium was measured at release of the bred tritium to the purge gas with hydrogen using the thermal release after irradiation method, where neutron irradiation was performed at JRR-3 reactor in JAERI or KUR reactor in Kyoto University. It is experimentally confirmed in this study that not a small portion of bred tritium is released to the purge gas in the form of HTO form ceramic breeder materials even when hydrogen is added to the purge gas. The chemical composition is to be decided by the competitive reaction at the grain surface of a ceramic breeder material where desorption reaction, isotope exchange reaction 1, isotope exchange reaction 2 and water formation reaction are considered to take part. Observation in this study implies that it is necessary to have a bred tritium recovery system applicable for both HT and HTO form to recover whole bred tritium. The chemical composition also decides the amount of tritium transferable to the cooling water of the electricity generation system through the structural material in the blanket system. Permeation behavior of tritium through some structural materials at various conditions are also discussed. (author)

Genotoxic and reprotoxic effects of tritium and external gamma irradiation on aquatic animals.

Science.gov (United States)

Adam-Guillermin, Christelle; Pereira, Sandrine; Della-Vedova, Claire; Hinton, Tom; Garnier-Laplace, Jacqueline

2012-01-01

.Because several calculated EDR10 values are ten times lower than background levels of γ irradiation the results of some studies either markedly call into question the adequacy of the benchmark value of 0.24 mGy/day for aquatic ecosystems that was recommended by Garnier-Laplace et al. (2006), or the dose rate estimates made in the original research, from which our EDR(10) values were derived, were under estimated, or were inadequate. For γ irradiation, the effects of several different dose rates on aquatic organisms were reviewed, and these ranged from 1 mGy/day to 18 Gy/day. DNA damage from exposure to y irradiation was studied more often than for tritium, but the major part of the literature addressed effects on reproduction and development. These data sets support the benchmark value of 0.24 mGy/day, which is recommended to protect aquatic ecosystems. RBEs, that describe the relative effectiveness of different radiation types to produce the same biological effect, were calculated using the available datasets. These RBE values ranged from 0.06 to 14.9, depending on the biological effect studied, and they had a mean of 3.1 ± 3.7 (standard deviation). This value is similar to the RBE factors of 2-3 recommended by international organizations responsible for providing guidance on radiation safety. Many knowledge gaps remain relative to the biological effects produced from exposure to tritium and y emitters. Among these are: Dose calculations: this review highlights several EDR(10) values that are below the normal range of background radiation. One explanation for this result is that dose rates were underestimated from uncertainties linked to the heterogenous distribution of tritium in cells. Therefore, the reliability of the concept of average dose to organisms must be addressed. Mechanisms of DNA DBS repair: very few studies address the most deleterious form of DNA damage, which are DNA DBSs. Future studies should focus on identifying impaired DNA DBS repair pathways and

In-situ tritium recovery from Li2O irradiated in fast neutron flux: BEATRIX-II initial results

International Nuclear Information System (INIS)

Kurasawa, T.; Slagle, O.D.; Hollenberg, G.W.; Verrall, R.A.

1990-10-01

The BEATRIX-II experiment in FFTF is an in-situ tritium recovery experiment to evaluate the tritium release characteristics of Li 2 O and its stability under fast neutron irradiation to extended burnups. This experiment includes two specimens: a thin annular specimen capable of temperature transients and a larger temperature gradient specimen. During the first 85 days of the operating cycle of the reactor, the tritium recovery rate of a temperature transient capsule was examined as a function of temperature, gas flow rate, gas composition and burnup. Temperature changes in the range from 525 to 625 degree C resulted in decreasing tritium inventory with increasing temperature. Lower gas flow rates resulted in slightly lower tritium release rates while gas composition changes affected the tritium release rate significantly, more than either flow rate or temperature changes. Three different sweep gases were used: He with 0.1% H 2 , He with 0.01% H 2 , and pure He. Decreasing the amount of hydrogen in the sweep gas decreased the steady-state release rate by as much as a factor of two. A temperature gradient capsule is more prototypic of the conditions expected in a fusion blanket and was designed to provide data that can be used in evaluating the operational parameters of a solid breeder in a blanket environment. The operation of this canister during the first 85 EFPD cycle suggests that Li 2 O is a viable solid breeder material. 9 refs., 5 figs., 3 tabs

1997 evaluation of tritium removal and mitigation technologies for Hanford Site wastewaters

International Nuclear Information System (INIS)

Jeppson, D.W.; Biyani, R.K.; Duncan, J.B.; Flyckt, D.L.; Mohondro, P.C.; Sinton, G.L.

1997-01-01

This report contains results of a biennial assessment of tritium separation technology and tritium nitration techniques for control of tritium bearing wastewaters at the Hanford Site. Tritium in wastewaters at Hanford have resulted from plutonium production, fuel reprocessing, and waste handling operations since 1944. this assessment was conducted in response to the Hanford Federal Facility Agreement and Consent Order

High pressure stability of lithium metatitanate and metazirconate: Insight from experiments & ab-initio calculations

Science.gov (United States)

Chitnis, Abhishek; Chakraborty, B.; Tripathi, B. M.; Tyagi, A. K.; Garg, Nandini

2018-02-01

Lithium metatitanate (LTO) and lithium metazirconate (LZO) are lithium rich ceramics which can be used as tritium breeder materials for thermonuclear reactors. In-situ x-ray diffraction and ab-initio studies at high pressure show that LTO has a higher bulk modulus than that of LZO. In fact these studies indicate that they are the least compressible of the known lithium rich ceramics like Li2O or Li4SiO4, which are potential candidates for blanket materials. These studies show that the TiO6 octahedra are responsible for the higher bulk modulus of LTO when compared to that of LZO. It has also been shown that the compressibility and distortion of the softer LiO6 octahedra can be controlled by altering the stacking sequence of the more rigid covalently bonded octahedra. This knowledge can be used by chemists to design new lithium based ceramics with higher bulk modulus. It was observed that LTO was stable upto 34 GPa. Ab initio DFT calculations helped to understand the anisotropy in compressibility of both LZO and LTO. This study also shows, that even though the empirical potentials developed by Vijaykumar et al. successfully determine the ambient pressure structure of lithium metatitanate, they cannot be used at non ambient conditions like high pressure [1].

Shape manipulation of ion irradiated Ag nanoparticles embedded in lithium niobate

International Nuclear Information System (INIS)

Wolf, Steffen; Rensberg, Jura; Johannes, Andreas; Ronning, Carsten; Thomae, Rainer; Smit, Frederick; Neveling, Retief; Bharuth-Ram, Krish; Moodley, Mathew; Bierschenk, Thomas; Rodriguez, Matias; Afra, Boshra; Ridgway, Mark; Hasan, Shakeeb Bin; Rockstuhl, Carsten

2016-01-01

Spherical silver nanoparticles were prepared by means of ion beam synthesis in lithium niobate. The embedded nanoparticles were then irradiated with energetic "8"4Kr and "1"9"7Au ions, resulting in different electronic energy losses between 8.1 and 27.5 keV nm"−"1 in the top layer of the samples. Due to the high electronic energy losses of the irradiating ions, molten ion tracks are formed inside the lithium niobate in which the elongated Ag nanoparticles are formed. This process is strongly dependent on the initial particle size and leads to a broad aspect ratio distribution. Extinction spectra of the samples feature the extinction maximum with shoulders on either side. While the maximum is caused by numerous remaining spherical nanoparticles, the shoulders can be attributed to elongated particles. The latter could be verified by COMSOL simulations. The extinction spectra are thus a superposition of the spectra of all individual particles. (paper)

High performance deuterium-tritium plasmas in TFTR

International Nuclear Information System (INIS)

Sabbagh, S.A.; Bell, M.G.

1995-03-01

Plasmas composed of nominally equal concentrations of deuterium and tritium (DT) have been created in TFTR with the goals of producing significant levels of fusion power and of examining the effects of DT fusion alpha particles. Conditioning of the limiter by the injection of lithium pellets has led to an approximate doubling of the energy confinement time, τ E , in supershot plasmas at high plasma current (I p ≤ 2.5 MA) and high heating power (P b ≤ 33 MW). Operation with DT typically results in an additional 20% increase in τ E . In the high poloidal beta, advanced tokamak regime in TFTR, confinement enhancement H triple-bond τ E /τ E ITER-89P > 4 has been obtained in a limiter H-mode configuration at moderate plasma current I p = 0.85 - 1.5 MA. By peaking the plasma current profile, β N dia triple-bond 10 8 tperpendicular > aB 0 /I p = 3 has been obtained in these plasmas, exceeding the β N limit for TFTR plasmas with lower internal inductance, l i . Confinement of alpha particles appears to be classical and losses due to collective effects have not been observed. While small fluctuations in fusion product loss were observed during ELMs, no large loss was detected in DT plasmas

Trial synthesis of Li{sub 2}Be{sub 2}O{sub 3} for high-functional tritium breeders

Energy Technology Data Exchange (ETDEWEB)

Hoshino, Tsuyoshi, E-mail: hoshino.tsuyoshi@jaea.go.jp [Breeding Functional Materials Development Group, Fusion Research and Development Directorate, Japan Atomic Energy Agency, 2-166, Obuchi, Omotedate, Rokkasho-mura, Kamikita-gun, Aomori 039-3212 (Japan); Oikawa, Fumiaki [Breeding Functional Materials Development Group, Fusion Research and Development Directorate, Japan Atomic Energy Agency, 2-166, Obuchi, Omotedate, Rokkasho-mura, Kamikita-gun, Aomori 039-3212 (Japan); Natori, Yuri; Kato, Kenichi; Sakka, Tomoko; Nakamura, Mutsumi; Tatenuma, Katsuyoshi [Kaken, Co. Ltd., 1044, Hori, Mito-city, Ibaraki 310-0903 (Japan)

2013-10-15

Highlights: • Mixtures of tritium breeder and neutron multiplier (Be or Be{sub 12}Ti) pebbles are being considered for increasing the tritium breeding ratio in DEMO blankets. • A high-functional tritium breeder such as lithium beryllium oxide (Li{sub 2}Be{sub 2}O{sub 3}) needs to be developed to compensate for this reaction under high-temperatures. • Solid-state reaction of LiOH·H{sub 2}O and BeO is well-suited for synthesizing Li{sub 2}Be{sub 2}O{sub 3}. • The optimum sintering temperature was selected from 1000 K to 1273 K by TG–DTA. -- Abstract: Mixtures of tritium breeder (lithium) and neutron multiplier (beryllium) are being considered for use in increasing the tritium breeding ratio in breeding blankets. However, lithium and beryllium react under normal operating conditions, and therefore, a high-functional tritium breeder such as lithium beryllium oxide (Li{sub 2}Be{sub 2}O{sub 3}) needs to be developed to compensate for this reaction under high-temperatures. LiOH·H{sub 2}O and BeO powders were mixed in stoichiometric proportions at a Li/Be molecular ratio of 1.0. The sintering temperature was established as 1073 K by thermogravimetric/differential thermal analysis (TG–DTA). The Li/Be molar ratio of the reaction products measured by inductively coupled plasma atomic emission spectroscopy (ICP-AES) after the reaction agreed with the nominal molar ratio obtained by mixing LiOH·H{sub 2}O and BeO. Crystal structure analysis of this powder was performed by the XRD technique. The XRD patterns of products were the same as those of Li{sub 2}Be{sub 2}O{sub 3} as listed in the JC-PDF-Card, and no impurities were indicated. The results indicate that the solid-state reaction of LiOH·H{sub 2}O and BeO is suitable for synthesizing lithium beryllium oxide (Li{sub 2}Be{sub 2}O{sub 3})

Tritium recovery from co-deposited layers using 193-nm laser

Science.gov (United States)

Shu, W. M.; Kawakubo, Y.; Nishi, M. F.

Recovery of tritium from co-deposited layers formed in deuterium-tritium plasma operations of the TFTR (Tokamak Fusion Test Reactor) was investigated by the use of an ArF excimer laser operating at the wavelength of 193 nm. At the laser energy density of 0.1 J/cm2, a transient spike of the tritium-release rate was observed at initial irradiation. Hydrogen isotopes were released in the form of hydrogen-isotope molecules during the laser irradiation in vacuum, suggesting that tritium can be recovered readily from the released gases. In a second experiment, hydrogen (tritium) recovery from the co-deposited layers on JT-60 tiles that had experienced hydrogen-plasma operations was investigated by laser ablation with a focused beam of the excimer laser. The removal rate of the co-deposited layers was quite low when the laser energy density was smaller than the ablation threshold (1.0 J/cm2), but reached 1.1 μm/pulse at the laser energy density of 7.6 J/cm2. The effective absorption coefficient in the co-deposited layers at the laser wavelength was determined to be 1.9 μm-1. The temperature of the surface during the irradiation at the laser energy density of 0.5 J/cm2 was measured on the basis of Planck's law of radiation, and the maximum temperature during the irradiation decreased from 3570 K at the initial irradiation to 2550 K at the 1000th pulse of the irradiation.

Neutronics experiments for uncertainty assessment of tritium breeding in HCPB and HCLL blanket mock-ups irradiated with 14 MeV neutrons

International Nuclear Information System (INIS)

Batistoni, P.; Angelone, M.; Pillon, M.; Villari, R.; Fischer, U.; Klix, A.; Leichtle, D.; Kodeli, I.; Pohorecki, W.

2012-01-01

Two neutronics experiments have been carried out at 14 MeV neutron sources on mock-ups of the helium cooled pebble bed (HCBP) and the helium cooled lithium lead (HCLL) variants of ITER test blanket modules (TBMs). These experiments have provided an experimental validation of the calculations of the tritium production rate (TPR) in the two blanket concepts and an assessment of the uncertainties due to the uncertainties on nuclear data. This paper provides a brief summary of the HCPB experiment and then focuses in particular on the final results of the HCLL experiment. The TPR has been measured in the HCLL mock-up irradiated for long times at the Frascati 14 MeV Neutron Generator (FNG). Redundant and well-assessed experimental techniques have been used to measure the TPR by different teams for inter-comparison. Measurements of the neutron and gamma-ray spectra have also been performed. The analysis of the experiment, carried out by the MCNP code with FENDL-2.1 and JEFF-3.1.1 nuclear data libraries, and also including sensitivity/uncertainty analysis, shows good agreement between measurements and calculations, within the total uncertainty of 5.9% at 1σ level. (paper)

Effect of Nd: YAG laser irradiation on surface properties and bond strength of zirconia ceramics.

Science.gov (United States)

Liu, Li; Liu, Suogang; Song, Xiaomeng; Zhu, Qingping; Zhang, Wei

2015-02-01

This study investigated the effect of neodymium-doped yttrium aluminum garnet (Nd: YAG) laser irradiation on surface properties and bond strength of zirconia ceramics. Specimens of zirconia ceramic pieces were divided into 11 groups according to surface treatments as follows: one control group (no treatment), one air abrasion group, and nine laser groups (Nd: YAG irradiation). The laser groups were divided by applying with different output power (1, 2, or 3 W) and irradiation time (30, 60, or 90 s). Following surface treatments, the morphological characteristics of ceramic pieces was observed, and the surface roughness was measured. All specimens were bonded to resin cement. After, stored in water for 24 h and additionally aged by thermocycling, the shear bond strength was measured. Dunnett's t test and one-way ANOVA were performed as the statistical analyses for the surface roughness and the shear bond strength, respectively, with α = .05. Rougher surface of the ceramics could be obtained by laser irradiation with higher output power (2 and 3 W). However, cracks and defects were also found on material surface. The shear bond strength of laser groups was not obviously increased, and it was significantly lower than that of air abrasion group. No significant differences of the shear bond strength were found among laser groups treated with different output power or irradiation time. Nd: YAG laser irradiation cannot improve the surface properties of zirconia ceramics and cannot increase the bond strength of the ceramics. Enhancing irradiation power and extending irradiation time cannot induce higher bond strength of the ceramics and may cause material defect.

Measurement of age of underground water, using tritium

International Nuclear Information System (INIS)

Chatani, Kunio; Kagami, Tadaaki; Tomita, Ban-ichi; Onuma, Akiko; Shoka, Yasushi

1978-01-01

Age of four kinds of underground water in Aichi prefecture was estimated by measuring a concentration of tritium. The tritium concentration was measured by the usual method. The first water-bearing zone of the shallow part, about 50m in depth, of Nobi plain is a new underground water cultivated within 20 years, whereas second water-bearing zone is an old underground water of 20 years old or more. No relationship of water flow between the first and the second water-bearing zone was observed. A very deep underground about 100m or more in depth, of the Nobi plain is confirmed to be infinite years old fossil water by measuring of tritium. The underground water in Atsumi peninsula is mostly a new underground water within 20 years. Only one out of eight showed the existence of old underground water before 20 years or more. The underground water of the granite area at Mikawa district is confirmed to be old underground water before 20 years or more. Alkaline underground water in the granite zone is considered to be very old in view of composition of water. The origin of underground water can be learned by tritium concentration, which shows whether the water is new water in the neighborhood of earth's surface or very old cultivated water. (Iwakiri, K.)

Effect of Er:YAG laser irradiation on bonding property of zirconia ceramics to resin cement.

Science.gov (United States)

Lin, Yihua; Song, Xiaomeng; Chen, Yaming; Zhu, Qingping; Zhang, Wei

2013-12-01

This study aimed to investigate whether or not an erbium: yttrium-aluminum-garnet (Er:YAG) laser could improve the bonding property of zirconia ceramics to resin cement. Surface treatments can improve the bonding properties of dental ceramics. However, little is known about the effect of Er:YAG laser irradiated on zirconia ceramics. Specimens of zirconia ceramic pieces were made, and randomly divided into 11 groups according to surface treatments, including one control group (no treatment), one air abrasion group, and nine Er:YAG laser groups. The laser groups were subdivided by applying different energy intensities (100, 200, or 300 mJ) and irradiation times (5, 10, or 15 sec). After surface treatments, ceramic pieces had their surface morphology observed, and their surface roughness was measured. All specimens were bonded to resin cement. Shear bond strength was measured after the bonded specimens were stored in water for 24 h, and additionally aged by thermocycling. Statistical analyses were performed using one way analysis of variance (ANOVA) and Tukey's test for shear bond strength, and Dunnett's t test for surface roughness, with α=0.05. Er:YAG laser irradiation changed the morphological characteristics of zirconia ceramics. Higher energy intensities (200, 300 mJ) could roughen the ceramics, but also caused surface cracks. There were no significant differences in the bond strength between the control group and the laser groups treated with different energy intensities or irradiation times. Air abrasion with alumina particles induced highest surface roughness and shear bond strength. Er:YAG laser irradiation cannot improve the bonding property of zirconia ceramics to resin cement. Enhancing irradiation intensities and extending irradiation time have no benefit on the bond of the ceramics, and might cause material defect.

Radiation damage in lithium orthosilicate

Energy Technology Data Exchange (ETDEWEB)

Noda, K.; Nakazawa, T.; Ishii, Y.; Fukai, K.; Watanabe, H. (Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment); Matsui, H.; Vollath, D.

1993-11-01

Radiation damage in lithium orthosilicate (Li[sub 4]SiO[sub 4]) and Al-doped Li[sub 4]SiO[sub 4] (Li[sub 3.7]Al[sub 0.1]SiO[sub 4]) irradiated with oxygen ions was studied with ionic conductivity measurements, Raman spectroscopy, Fourier transform infrared photo-acoustic spectroscopy (FT-IR PAS) and transmission electron microscopy. It was seen from the ionic conductivity measurements that lithium-ion vacancies were introduced as irradiation defects for Li-ions sites in both materials due to the irradiation. By the Raman spectroscopy, oxygen atoms in SiO[sub 4] tetrahedra were considered to be preferentially displaced due to the irradiation for Li[sub 4]SiO[sub 4], although only a decrease of the number of SiO[sub 4] tetrahedra occurred for Li[sub 3.7]Al[sub 0.1]SiO[sub 4] by displacement of both silicon and oxygen atoms. Decomposition of SiO[sub 4] tetrahedra and formation of some new phases having Si-O-Si and Si-O bonds were found to take place for both Li[sub 4]SiO[sub 4] and Li[sub 3.7]Al[sub 0.1]SiO[sub 4] by FT-IR PAS. In the electron microscopy, damage microstructure consisting of many voids or cavities and amorphization were observed for Li[sub 4]SiO[sub 4] irradiated with oxygen ions. The recovery behavior of radiation damage mentioned above was also investigated. (author).

Environmental effects of normal and off-normal releases of tritium from CTR systems

International Nuclear Information System (INIS)

McKone, T.E.

1978-08-01

Near term fusion technology will utilize the deuterium-tritium reaction. To quantify the magnitude of the hazard presented by major tritium release mechanisms, a method is presented for determining doses to the public from releases of tritium as tritiated water vapor or tritiated lithium compounds. Inclusion of this method in a computer model is described. This model uses the Gaussian dispersion method to predict distribution of tritium species in the downwind environment. Movement of tritium into biological systems is determined by treating these systems as a series of interacting water compartments. Dispersion and uptake calculations are applied to two sample sites in order to predict health effects. These effects are compared to the long range effect of introducing tritium into the world water system

Commercial Light Water Reactor -Tritium Extraction Facility Process Waste Assessment (Project S-6091)

Energy Technology Data Exchange (ETDEWEB)

Hsu, R.H.; Delley, A.O.; Alexander, G.J.; Clark, E.A.; Holder, J.S.; Lutz, R.N.; Malstrom, R.A.; Nobles, B.R. [Westinghouse Savannah River Co., Aiken, SC (United States); Carson, S.D. [Sandia National Laboratories, New Mexico, NM (United States); Peterson, P.K. [Sandia National Laboratories, New Mexico, NM (United States)

1997-11-30

The Savannah River Site (SRS) has been tasked by the Department of Energy (DOE) to design and construct a Tritium Extraction Facility (TEF) to process irradiated tritium producing burnable absorber rods (TPBARs) from a Commercial Light Water Reactor (CLWR). The plan is for the CLWR-TEF to provide tritium to the SRS Replacement Tritium Facility (RTF) in Building 233-H in support of DOE requirements. The CLWR-TEF is being designed to provide 3 kg of new tritium per year, from TPBARS and other sources of tritium (Ref. 1-4).The CLWR TPBAR concept is being developed by Pacific Northwest National Laboratory (PNNL). The TPBAR assemblies will be irradiated in a Commercial Utility light water nuclear reactor and transported to the SRS for tritium extraction and processing at the CLWR-TEF. A Conceptual Design Report for the CLWR-TEF Project was issued in July 1997 (Ref. 4).The scope of this Process Waste Assessment (PWA) will be limited to CLWR-TEF processing of CLWR irradiated TPBARs. Although the CLWR- TEF will also be designed to extract APT tritium-containing materials, they will be excluded at this time to facilitate timely development of this PWA. As with any process, CLWR-TEF waste stream characteristics will depend on process feedstock and contaminant sources. If irradiated APT tritium-containing materials are to be processed in the CLWR-TEF, this PWA should be revised to reflect the introduction of this contaminant source term.

Commercial Light Water Reactor -Tritium Extraction Facility Process Waste Assessment (Project S-6091)

International Nuclear Information System (INIS)

Hsu, R.H.; Delley, A.O.; Alexander, G.J.; Clark, E.A.; Holder, J.S.; Lutz, R.N.; Malstrom, R.A.; Nobles, B.R.; Carson, S.D.; Peterson, P.K.

1997-01-01

The Savannah River Site (SRS) has been tasked by the Department of Energy (DOE) to design and construct a Tritium Extraction Facility (TEF) to process irradiated tritium producing burnable absorber rods (TPBARs) from a Commercial Light Water Reactor (CLWR). The plan is for the CLWR-TEF to provide tritium to the SRS Replacement Tritium Facility (RTF) in Building 233-H in support of DOE requirements. The CLWR-TEF is being designed to provide 3 kg of new tritium per year, from TPBARS and other sources of tritium (Ref. 1-4).The CLWR TPBAR concept is being developed by Pacific Northwest National Laboratory (PNNL). The TPBAR assemblies will be irradiated in a Commercial Utility light water nuclear reactor and transported to the SRS for tritium extraction and processing at the CLWR-TEF. A Conceptual Design Report for the CLWR-TEF Project was issued in July 1997 (Ref. 4).The scope of this Process Waste Assessment (PWA) will be limited to CLWR-TEF processing of CLWR irradiated TPBARs. Although the CLWR- TEF will also be designed to extract APT tritium-containing materials, they will be excluded at this time to facilitate timely development of this PWA. As with any process, CLWR-TEF waste stream characteristics will depend on process feedstock and contaminant sources. If irradiated APT tritium-containing materials are to be processed in the CLWR-TEF, this PWA should be revised to reflect the introduction of this contaminant source term

Shape manipulation of ion irradiated Ag nanoparticles embedded in lithium niobate

NARCIS (Netherlands)

Wolf, S.; Rensberg, J.; Johannes, A.; Thomae, R.; Smit, F.; Neveling, R.; Moodley, M.; Bierschenk, T.; Rodriquez, M.; Afra, B.; Hasan, Shakeeb Bin; Rockstuhl, C.; Ridgway, M.; Bharuth-Ram, K.; Ronning, C.

2016-01-01

Spherical silver nanoparticles were prepared by means of ion beam synthesis in lithium niobate. The embedded nanoparticles were then irradiated with energetic 84Kr and 197Au ions, resulting in different electronic energy losses between 8.1 and 27.5 keV nm−1 in the top layer of the samples. Due to

Tritium systems concepts for the next European torus (NET)

International Nuclear Information System (INIS)

Sood, S.K.; Bagli, K.S.; Busigin, A.; Kveton, O.K.; Dombra, A.H.; Miller, A.I.

1986-09-01

The study deals with the design of the various tritium processing facilities that will be required for the Next European Torus (NET) design. The reference data for the design of the NET Tritium Systems was provided by the NET team. Significant achievements of this study were: (a) Identification of new ways of handling some problems for example: 1) Recovery of tritium from the helium purge of the lithium-ceramic blanket using a novel Adsoprtion and Catalytic Exchange Process, 2) A new way of combining fuel component separation and coolant water detritiation using cryogenic distillation, 3) The use of parasitic refrigeration for the cryogenic isotope separation, 4) Tritium extraction from effluent gas streams at their respective sources, 5) Attempt to eliminate the need for Air Cleanup Systems. (b) Identification of uncertainties, for example: composition of plasma exhaust, required helium purge rate of Li-Pb for tritium recovery, uncertainty in requirements for decontaminating blanket sectors, etc. (c) Review of ways to limit tritium permeation into steam by swamping with hydrogen and to provide quantitative estimates for this permeation

Tritium retention properties of tungsten, graphite and co-deposited carbon film

International Nuclear Information System (INIS)

Nobuta, Y.; Hatano, Y.; Matsuyama, M.; Abe, S.; Akamaru, S.; Yamauchi, Y.; Hino, T.; Suzuki, S.; Akiba, M.

2014-01-01

DT + ion irradiation was performed on polycrystalline tungsten, graphite and carbon film and both the amount of retained tritium and the reduction of retained tritium after preservation in vacuum were investigated using an IP technique and BIXS. In addition, the relationship between the retention properties of tritium and the microstructure of graphite and carbon film were studied with Raman spectroscopy. The amount of retained tritium in tungsten was smaller than in both graphite and carbon film. After 1 keV of DT + irradiation, graphite showed no reduction of the amount of retained tritium after six months preservation while that of carbon film decreased by approximately 20% after 40 days preservation. It was suggested that this difference might be associated with differences in the microstructure between graphite and carbon film. In tungsten, the amount of retained tritium decreased to approximately half after 18 days preservation. As the incident energy of implanted tritium to tungsten increased, the decrease in tritium retention during preservation became slower. Tungsten's properties of releasing tritium while preserved in vacuum would be a useful tool for the reduction/removal of retained tritium

Accelerator Production of Tritium Programmatic Environmental Impact Statement Input Submittal

International Nuclear Information System (INIS)

Miller, L.A.; Greene, G.A.; Boyack, B.E.

1996-02-01

The Programmatic Environmental Impact Statement for Tritium Supply and Recycling considers several methods for the production of tritium. One of these methods is the Accelerator Production of Tritium. This report summarizes the design characteristics of APT including the accelerator, target/blanket, tritium extraction facility, and the balance of plant. Two spallation targets are considered: (1) a tungsten neutron-source target and (2) a lead neutron-source target. In the tungsten target concept, the neutrons are captured by the circulating He-3, thus producing tritium; in the lead target concept, the tritium is produced by neutron capture by Li-6 in a surrounding lithium-aluminum blanket. This report also provides information to support the PEIS including construction and operational resource needs, waste generation, and potential routine and accidental releases of radioactive material. The focus of the report is on the impacts of a facility that will produce 3/8th of the baseline goal of tritium. However, some information is provided on the impacts of APT facilities that would produce smaller quantities

Effect of ultraviolet light irradiation and sandblasting treatment on bond strengths between polyamide and chemical-cured resin.

Science.gov (United States)

Asakawa, Yuya; Takahashi, Hidekazu; Iwasaki, Naohiko; Kobayashi, Masahiro

2014-01-01

The aim of this study was to evaluate the effects of ultraviolet light (UV) irradiation and sandblasting treatment on the shear bond strength between polyamide and chemical-cured resin. Three types of commercial polyamides were treated using UV irradiation, sandblasting treatment, and a combining sandblasting and UV irradiation. The shear bond strength was measured and analyzed using the Kruskal-Wallis test (α=0.05). Comparing shear bond strengths without surface treatment, from 4.1 to 5.7 MPa, the UV irradiation significantly increased the shear bond strengths except for Valplast, whose shear bond strengths ranged from 5.2 to 9.3 MPa. The sandblasting treatment also significantly increased the shear bond strengths (8.0 to 11.4 MPa). The combining sandblasting and UV irradiation significantly increased the shear bond strengths (15.2 to 18.3 MPa) comparing without surface treatment. This combined treatment was considered the most effective at improving the shear bond strength between polyamide and chemical-cured resin.

Dissolved nitrogen in liquid lithium - a problem in fusion reactor chemistry

International Nuclear Information System (INIS)

Hubberstey, P.

1984-01-01

When dissolved in liquid lithium, nitrogen adopts the role filled by oxygen in liquid sodium systems, reacting readily with stainless steel containment materials to form Li 9 CrN 5 as a surface product; extended reaction leads to pronounced corrosion and embrittlement problems. It also interacts with both carbon and silicon impurities forming Li 2 NCN and Li 5 SiN 3 , respectively; it is inert, however, to oxygen impurity. Although dissolved nitrogen reacts with neither the tritium generated in the breeding process nor the lead added to act as a neutron multiplier, its presence may seriously influence tritium recovery processes since it reacts with and hence may poison the majority of the transition metals (Y,Ti,Zr) presently being considered as tritium getter materials. Its reactivity with these metals forms the basis of the hot trapping technique used to remove dissolved nitrogen from liquid lithium systems; cold trapping is ineffective because of its large solubility even at temperatures just above the melting point of pure lithium (453.6K). Whenever possible, the chemistry of nitrogen dissolved in liquid lithium is rationalised using the thermodynamic concepts and its significance to fusion reactor technology stressed. (author)

Advanced electrolytic cascade process for tritium recovery from irradiated heavy water moderator (Preprint No. PD-15)

International Nuclear Information System (INIS)

Ragunathan, P.; Mitra, S.K.; Jain, D.K.; Nayar, M.G.; Ramani, M.P.S.

1989-04-01

The paper briefly describes a design study of an electrolytic cascade process plant for enrichment and recovery of tritium from irradiated heavy water moderators from Rajasthan Atomic Power Station Reactors. In direct multistage electrolysis process, tritiated heavy water from the reactor units is fed to the electrolytic cell modules arranged in the form of a cascade where it is enriched and decomposed into O 2 gas stream and D 2 /DT gas stream. The direct electrolysis of tritiated heavy water allows tritium to be concentrated in the aqueous phase. Several stages are used to achieve the necessary enrichment. The cascade plant incorporates the advanced electrolyser technology developed in Bhabha Atomic Research Centre (Bombay) using porous nickel electrodes, capable o f high current density operation at reduced energy consumption for electrolysis. (author). 3 tabs

Experimental study of gaseous lithium deuterides and lithium oxides. Implications for the use of lithium and Li2O as breeding materials in fusion reactor blankets

International Nuclear Information System (INIS)

Ihle, H.R.; Wu, C.H.; Kudo, H.

1980-01-01

In addition to LiH, which has been studied extensively by optical spectroscopy, the existence of a number of other stable lithium hydrides has been predicted theoretically. By analysis of the saturated vapour over dilute solutions of the hydrogen isotopes in lithium, using Knudsen effusion mass spectrometry, all lithium hydrides predicted to be stable were found. Solutions of deuterium in lithium were used predominantly because of practical advantages for mass spectrometric measurements. The heats of dissociation of LiD, Li 2 D, LiD 2 and Li 2 D 2 , and the binding energies of their singly charged positive ions were determined, and the constants of the gas/liquid equilibria were calculated. The existence of these lithium deuterides in the gas phase over solutions of deuterium in lithium leads to enrichment of deuterium in the gas above 1240 K. The enrichment factor, which increases exponentially with temperature and is independent of concentration for low concentrations of deuterium in the liquid, was determined by Rayleigh distillation experiments. It was found that it is thermodynamically possible to separate deuterium from lithium by distillation. One of the alternatives to the use of lithium in (D,T)-fusion reactors as tritium-breeding blanket material is to employ solid lithium oxide. This has a high melting point, a high lithium density and still favourable tritium-breeding properties. Because of its rather high volatility, an experimental study of the vaporization of Li 2 O was undertaken by mass spectrometry. It vaporizes to give lithium and oxygen, and LiO, Li 2 O, Li 3 O and Li 2 O 2 . The molecule Li 3 O was found as a new species. Heats of dissociation, binding energies of the various ions and the constants of the gas/solid equilibria were determined. The effect of using different materials for the Knudsen cells and the relative thermal stabilities of lithium-aluminium oxides were also studied. (author)

Materials considerations in accelerator targets

International Nuclear Information System (INIS)

Peacock, H. B. Jr.; Iyer, N. C.; Louthan, M. R. Jr.

1995-01-01

Future nuclear materials production and/or the burn-up of long lived radioisotopes may be accomplished through the capture of spallation produced neutrons in accelerators. Aluminum clad-lead and/or lead alloys has been proposed as a spallation target. Aluminum was the cladding choice because of the low neutron absorption cross section, fast radioactivity decay, high thermal conductivity, and excellent fabricability. Metallic lead and lead oxide powders were considered for the target core with the fabrication options being casting or powder metallurgy (PM). Scoping tests to evaluate gravity casting, squeeze casting, and casting and swaging processes showed that, based on fabricability and heat transfer considerations, squeeze casting was the preferred option for manufacture of targets with initial core cladding contact. Thousands of aluminum clad aluminum-lithium alloy core targets and control rods for tritium production have been fabricated by coextrusion processes and successfully irradiated in the SRS reactors. Tritium retention in, and release from, the coextruded product was modeled from experimental and operational data. The model assumed that tritium atoms, formed by the 6Li(n,a)3He reaction, were produced in solid solution in the Al-Li alloy. Because of the low solubility of hydrogen isotopes in aluminum alloys, the irradiated Al-Li rapidly became supersaturated in tritium. Newly produced tritium atoms were trapped by lithium atoms to form a lithium tritide. The effective tritium pressure required for trap or tritide stability was the equilibrium decomposition pressure of tritium over a lithium tritide-aluminum mixture. The temperature dependence of tritium release was determined by the permeability of the cladding to tritium and the local equilibrium at the trap sites. The model can be used to calculate tritium release from aluminum clad, aluminum-lithium alloy targets during postulated accelerator operational and accident conditions. This paper describes

Tritium behaviour in ceramic breeder blankets

International Nuclear Information System (INIS)

Miller, J.M.

1989-01-01

Tritium release from the candidate ceramic materials, Li 2 O, LiA10 2 , Li 2 SiO 3 , Li 4 SiO 4 and Li 2 ZrO 3 , is being investigated in many blanket programs. Factors that affect tritium release from the ceramic into the helium sweep gas stream include operating temperature, ceramic microstructure, tritium transport and solubility in the solid. A review is presented of the material properties studied and of the irradiation programs and the results are summarized. The ceramic breeder blanket concept is briefly reviewed

Tritium processing and containment technology for fusion reactors: perspective and status

International Nuclear Information System (INIS)

Maroni, V.A.

1976-01-01

This paper reviews the status of selected tritium processing and containment technologies that will be required to support the development of the fusion energy program. Considered in order are the fuel conditioning and recycle systems, the containment and cleanup systems, the blanket processing systems, and two unique problems relating to tritium interactions in neutral beam injectors and first wall coolant circuits. The major technical problem areas appear to lie in the development of (1) high-capacity, rapid recycle plasma chamber evacuation systems; (2) large-capacity (greater than or equal to 100,000 cfm) air handling and processing systems for atmospheric detritiation; (3) tritium recovery technology for liquid lithium blanket concepts; (4) tritium compatible neutral injector systems; and (5) an overall approach to tritium handling and containment that guarantees near zero release to the environment at a bearable cost

Potential design modifications for the High Yield Lithium Injection Fusion Energy (HYLIFE) reaction chamber

International Nuclear Information System (INIS)

Pitts, J.H.; Hovingh, J.; Meier, W.R.; Monsler, M.J.; Powell, E.G.; Walker, P.E.

1979-01-01

Generation of electric power from inertial confinement fusion requires a reaction chamber. One promising type, the High Yield Lithium Injection Fusion Energy (HYLIFE) chamber, includes a falling array of liquid lithium jets. These jets act as: (1) a renewable first wall and blanket to shield metal components from x-ray and neutron exposure, (2) a tritium breeder to replace tritium burned during the fusion process, and (3) an absorber and transfer medium for fusion energy. Over 90% of the energy produced in the reaction chamber is absorbed in the lithium jet fall. Design aspects are included

A new bonded catalyst for safe lithium-thionyl chloride batteries

Science.gov (United States)

Walsh, F.; Hopewood, J.

1982-08-01

The goal of the research effort was to demonstrate that a new class of organometallic cathode catalysts, the TAAs, are stable in thionyl chloride and that they significantly improve the power performance of lithium-thionyl chloride primary batteries. A number of TAAs were evaluated and shown to be active catalysts. Included in this evaluation were TAAs which were covalently bonded to the supporting carbon electrode material; a covalently bonded catalyst has the potential advantage that it will not dissolve into the electrolyte and negatively affect anode performance. During the six month research program, the TAAS were shown to: significantly improve cathode performance in Li/SOCl2 cells; improve cathode capacity; improve cathode performance throughout long-term tests; and not affect anode performance. Further work is needed to develop data in cell studies on temperature range, shelf life, voltage delay effects, energy/power density as a function of rate, and factors affecting electrode capacity. Battery performance in stress tests to develop safety and cost data is also needed.

Analysis of Beryllium Having Irradiated at the RSG-GAS Core using ORIGEN2 Code

International Nuclear Information System (INIS)

Jaja Sukmana; Jonnie AK; S-Suwarto; Irwan

2012-01-01

Analysis of activation products generated by irradiated beryllium at the RSG-GAS core has been done using ORIGEN2 code. By assuming that irradiation is 176 days, neutron flux average of 2.30e+14 n/cm 2 s, radioisotopes rose from activated Be are tritium, lithium, beryllium, carbon, magnesium, aluminum, silicon, argon, calcium, scandium, vanadium, chromium, manganese, iron, cobalt, nickel, copper, zinc, silver, and lead. The highest activity after 100 days of irradiation demonstrated by Be-10 (7.99 E-03 Curie), H-3 (2.97 E-03 Curie), Cr-51, Fe-55 and Co-60. Radioactivity generated getting smaller when irradiation time are long. From this analysis it can be conclude that radioactivity was caused by impurities present in Be such as Mn-54, Fe-59, Zn-65, and Li-6. (author)

Preparation of thermal resistant-enhanced separators for lithium ion battery by electron beam irradiation

Energy Technology Data Exchange (ETDEWEB)

Sohn, Joon Yong; Shin, Junhwa; Nho, Youngchang [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2012-03-15

Micro-porous membrane made of polyethylene (PE) or polypropylene (PP) is most widely used as physical separators between the cathode and anode in lithium secondary batteries. However, the polymer membranes so soften or melt when the temperature reaches 130 .deg. C or higher because of thermal shrinkage of the polyolefin separators, and thaw low thermal stability may cause internal short circuiting or lead to thermal runaway. In this study, to realize a highly safe battery, we prepared three type separators as crosslinked PE separator, polymer-coated PE separator, and ceramic-coated PE separators, for lithium secondary battery by electron beam irradiation. We prepared crosslinked PE separators with the improved thermal stability by irradiating a commercial PE separator with an electron beam. A polymer-coated PE separator was prepared by a dip-coating of PVDF-HFP/PEGDMA on both sides of a PE separator followed by an electron beam irradiation. Ceramic-coated PE separator was prepared by coating ceramic particles on a PE separator followed by an electron beam irradiation. The prepared separators were characterized with FT-IR, SEM, electrolyte uptake, ion conductivity, thermal shrinkage and battery performance test.

Tritium behavior in ITER beryllium

International Nuclear Information System (INIS)

Longhurst, G.R.

1990-10-01

The beryllium neutron multiplier in the ITER breeding blanket will generate tritium through transmutations. That tritium constitutes a safety hazard. Experiments evaluating tritium storage and release mechanisms have shown that most of the tritium comes out in a burst during thermal ramping. A small fraction of retained tritium is released by thermally activated processes. Analysis of recent experimental data shows that most of the tritium resides in helium bubbles. That tritium is released when the bubbles undergo swelling sufficient to develop porosity that connects with the surface. That appears to occur when swelling reaches about 10--15%. Other tritium appears to be stored chemically at oxide inclusions, probably as Be(OT) 2 . That component is released by thermal activation. There is considerable variation in published values for tritium diffusion through the beryllium and solubility in it. Data from experiments using highly irradiated beryllium from the Idaho National Engineering Laboratory showed diffusivity generally in line with the most commonly accepted values for fully dense material. Lower density material, planned for use in the ITER blanket may have very short diffusion times because of the open structure. The beryllium multiplier of the ITER breeding blanket was analyzed for tritium release characteristics using temperature and helium production figures at the midplane generated in support of the ITER Summer Workshop, 1990 in Garching. Ordinary operation, either in Physics or Technology phases, should not result in the release of tritium trapped in the helium bubbles. Temperature excursions above 600 degree C result in large-scale release of that tritium. 29 refs., 10 figs., 3 tabs

Analysis of tritium production in concentric spheres of oralloy and 6LiD irradiated by 14-MeV neutrons

International Nuclear Information System (INIS)

Fawcett, L.R. Jr.; Roberts, R.R. II; Hunter, R.E.

1988-03-01

Tritium production and activation of radiochemical detector foils in a sphere of 6 LiD with an oralloy core irradiated by a central source of 14-MeV neutrons have been calculated and compared with experimental measurements. The experimental assembly consisted of an oralloy sphere surrounded by three solid 6 LiD concentric shells with ampules of 6 LiH and 7 LiH and activation foils located in several positions throughout the assembly. The Los Alamos Monte Carlo Neutron Photon Transport Code (MCNP) was used to calculate neutron transport throughout the system, tritium production in the ampules, and foil activation. The overall experimentally observed-to-calculated ratios of tritium production were 0.996 +- 2.5% in 6 Li ampules and 0.903 +- 5.2% in 7 Li ampules. Observed-to-calculated ratios for foil activation are also presented. 11 refs., 4 figs., 7 tabs

Dosimetric properties of dysprosium doped lithium borate glass irradiated by 6 MV photons

Science.gov (United States)

Ab Rasid, A.; Wagiran, H.; Hashim, S.; Ibrahim, Z.; Ali, H.

2015-07-01

Undoped and dysprosium doped lithium borate glass system with empirical formula (70-x) B2O3-30 Li2O-(x) Dy2O3 (x=0.1, 0.3, 0.5, 0.7, 1.0 mol%) were prepared using the melt-quenching technique. The dosimetric measurements were performed by irradiating the samples to 6 MV photon beam using linear accelerator (LINAC) over a dose range of 0.5-5.0 Gy. The glass series of dysprosium doped lithium borate glass produced the best thermoluminescence (TL) glow curve with the highest intensity peak from sample with 1.0 mol% Dy2O3 concentration. Minimum detectable dose was detected at 2.24 mGy, good linearity of regression coefficient, high reproducibility and high sensitivity compared to the undoped glass are from 1.0 mol% dysprosium doped lithium borate glass. The results indicated that the series of dysprosium doped lithium glasses have a great potential to be considered as a thermoluminescence dosimetry (TLD).

Effect of Irradiation on the Shear Bond Strength of Self-adhesive ...

African Journals Online (AJOL)

2016-02-05

Feb 5, 2016 ... changes in the crystalline structure of dental hard tissues. Keywords: Bond strength, irradiation, self-adhesive luting cement. Effect of Irradiation on the .... The metal ring was connected with the cross-head and loaded (speed 1 ...

Does laser diode irradiation improve the degree of conversion of simplified dentin bonding systems?

Directory of Open Access Journals (Sweden)

Leticia Ferreira de Freitas BRIANEZZI

Full Text Available Abstract Simplified dentin-bonding systems are clinically employed for most adhesive procedures, and they are prone to hydrolytic degradation. Objective This study aimed to investigate the effect of laser diode irradiation on the degree of conversion (DC, water sorption (WS, and water solubility (WSB of these bonding systems in an attempt to improve their physico-mechanical resistance. Material and Methods Two bonding agents were tested: a two-step total-etch system [Adper™ Single Bond 2, 3M ESPE (SB] and a universal system [Adper™ Single Bond Universal, 3M ESPE (SU]. Square-shaped specimens were prepared and assigned into 4 groups (n=5: SB and SU (control groups – no laser irradiation and SB-L and SU-L [SB and SU laser (L – irradiated groups]. DC was assessed using Fourier transform infrared spectroscopy with attenuated total reflectance. Additional uncured resin samples (≈3.0 µL, n=5 of each adhesive were also scanned for final DC calculation. For WS/WSB tests, similar specimens (n=10 were prepared and measured by monitoring the mass changes after dehydration/water storage cycles. For both tests, adhesive fluids were dropped into standardized Teflon molds (6.0×6.0×1.0 mm, irradiated with a 970-nm laser diode, and then polymerized with an LED-curing unit (1 W/cm2. Results Laser irradiation immediately before photopolymerization increased the DC (% of the tested adhesives: SB-L>SB>SU-L>SU. For WS/WSB (μg/mm3, only the dentin bonding system (DBS was a significant factor (pSU. Conclusion Irradiation with a laser diode improved the degree of conversion of all tested simplified dentin bonding systems, with no impact on water sorption and solubility.

New facility for post irradiation examination of neutron irradiated beryllium

International Nuclear Information System (INIS)

Ishitsuka, Etsuo; Kawamura, Hiroshi

1995-01-01

Beryllium is expected as a neutron multiplier and plasma facing materials in the fusion reactor, and the neutron irradiation data on properties of beryllium up to 800 degrees C need for the engineering design. The acquisition of data on the tritium behavior, swelling, thermal and mechanical properties are first priority in ITER design. Facility for the post irradiation examination of neutron irradiated beryllium was constructed in the hot laboratory of Japan Materials Testing Reactor to get the engineering design data mentioned above. This facility consist of the four glove boxes, dry air supplier, tritium monitoring and removal system, storage box of neutron irradiated samples. Beryllium handling are restricted by the amount of tritium;7.4 GBq/day and 60 Co;7.4 MBq/day

Safety and feasibility research of CIPT-Ⅱ irradiation device

International Nuclear Information System (INIS)

Zhang Zhihua; Mi Xiangmiao; Li Rundong

2014-01-01

CITP-Ⅱ irradiation device, which is specially designed for fusion tritium breeder research, works in a thermal neutron reactor. With lithium orthosilicate as the breeder, the safety analysis was done to work out the device's influence on physical parameters of the reactor and get the breeder's temperature distribution and thermo-technical features in the n-γ field. The stiffness and strength were checked, and also the safety characters of the device were assessed. The feasibility of gap gas regulating the temperature and gas refueling the breeder was demonstrated. The calculation and analysis results provide data for comprehensive performance assessment. (authors)

Tensile Bond Strengths of Two Adhesives on Irradiated and Nonirradiated Human Dentin

Directory of Open Access Journals (Sweden)

Cécile Bernard

2015-01-01

Full Text Available The aim of this study was to assess the effect of radiotherapy on bond efficiency of two different adhesive systems using tensile bond strength test. Twenty extracted teeth after radiotherapy and twenty nonirradiated extracted teeth were used. The irradiation was applied in vivo to a minimal dose of 50 Gy. The specimens of each group were randomly assigned to two subgroups to test two different adhesive systems. A three-step/etch-and-rinse adhesive system (Optibond FL and a two-steps/self-etch adhesive system (Optibond XTR were used. Composite buildups were performed with a nanohybrid composite (Herculite XTR. All specimens were submitted to thermocycling ageing (10000 cycles. The specimens were sectioned in 1 mm2 sticks. Microtensile bond strength tests were measured. Nonparametric statistical analyses were performed due to nonnormality of data. Optibond XTR on irradiated and nonirradiated teeth did not show any significant differences. However, Optibond FL bond strength was more effective on nonirradiated teeth than on irradiated teeth. Within the limitations of an in vitro study, it can be concluded that radiotherapy had a significant detrimental effect on bond strength to human dentin. However, it seems that adhesive choice could be adapted to the substrata. According to the present study, the two-steps/self-etch (Optibond XTR adhesive system tested could be more effective on irradiated dentin compared to three-steps/etch-and-rinse adhesive system (Optibond FL.

Effects of perfluorochemical emulsion on the timing of administration and irradiation in tumor bearing mice

International Nuclear Information System (INIS)

Hishikawa-Itoh, Youko; Ayakawa, Yoshio; Miyata, Nobuki

1988-01-01

Perfluorochemical content was examined periodically, in blood, tumor and some organs using gas chromatography, after Fluosol-DA saline 20 % (FDAS) was injected into LLC bearing mice. The blood half-life of FDAS in LLC bearing mice was 3.76 hrs (5 ml/kg injection) or 6.15 hrs (20 ml/kg injection) respectively, and FDAS almost disapeared from the blood after about 2 days (5 ml/kg) and 3 days (20 ml/kg) of FDAS-injection. Most of FDAS was accumulated into spleen and the liver. FDAS accumulation into the tumor tissue was 1 ∼ 6 % of injected-FDAS dose and the peak of FDAS accumulation was 1 ∼ 3 days after injection. The timing of FDAS-injection and irradiation in tumor bearing mice determined according to the results above (half-life and accumulation of FDAS in tumor). FDAS (5, 10, 20 ml/kg) was injected to LLC-bearing mice on 3, 2, 1 and 0 day before irradiation and they were irradiated 15 Gray under oxygen-breathing, respectively. FDAS-injected groups before irradiation (3, 2, 1 day before, respectively) showed a tendency of tumor growth delay, but didn't show significant difference as compared with oxygen-breathing group without FDAS, because they had not enough effective FDAS content in the blood. Although the FDAS-injected groups just before irradiation significantly showed the delay of tumor growth. These results demonstrate that oxygen and FDAS existing in the blood injected just before irradiation effectively delay tumor growth in which the lowest effective dose is 5 ml/kg. In the case of clinical application of FDAS, FDAS may be most effective, when administrated just before irradiation in every fractionated irradiation. (author)

Effect of UV irradiation on the shear bond strength of titanium with segmented polyurethane through gamma-mercapto propyl trimethoxysilane.

Science.gov (United States)

Sakamoto, Harumi; Hirohashi, Yohei; Doi, Hisashi; Tsutsumi, Yusuke; Suzuki, Yoshiaki; Noda, Kazuhiko; Hanawa, Takao

2008-01-01

The objective of this study was to investigate the effect of UV irradiation on shear bond strength between a titanium (Ti) and a segmented polyurethane (SPU) composite through gamma-mercapto propyl trimethoxysilane (gamma-MPS). To this end, the shear bond strength of Ti/SPU interface of Ti-SPU composite under varying conditions of ultraviolet ray (UV) irradiation was evaluated by a shear bond test. The glass transition temperatures of SPU with and without UV irradiation were also determined using differential scanning calorimetry. It was found that the shear bond strength of Ti/SPU interface increased with UV irradiation. However, excessive UV irradiation decreased the shear bond strength of Ti/SPU interface. Glass transition temperature was found to increase during 40-60 seconds of UV irradiation. In terms of durability after immersion in water at 37 degrees C for 30 days, shear bond strength was found to improve with UV irradiation. In conclusion, UV irradiation to a Ti-SPU composite was clearly one of the means to improve the shear bond strength of Ti/SPU interface.

Parametric analysis of LIBRETTO-4 and 5 in-pile tritium transport model on EcosimPro

Energy Technology Data Exchange (ETDEWEB)

Alcalde, Pablo Martínez, E-mail: pablomiguel.martinez@externos.ciemat.es [Universidad Nacional de Educación a Distancia (UNED), c/Juan del Rosal 12, 28040 Madrid (Spain); Moreno, Carlos; Ibarra, Ángel [CIEMAT, Avda. Complutense 40, 28040 Madrid (Spain)

2014-10-15

Highlights: • Introduction of a new tritium transport model of LIBRETTO-4 and 5 on EcosimPro{sup ®}. • Analysis of model input parameter and variable sensitivities and effects on tritium simulated fluxes. • Demonstrations of high tritium out-flux dependencies on lead-lithium parameters. • Rough fitting achievements proposed by Li17Pb solubility or recombination increase. - Abstract: A new model for LIBRETTO-4/1, 4/2 and 5 experiments have been developed on ECOSIMPro{sup ©} tool to simulate tritium in-pile breeding and transport into two separate purge gas channels with He + 0.1%H{sub 2}. Release from lead lithium eutectic plenum with coupled permeation through an austenitic steel wall on the first and single permeation through EUROFER-97 in the temperature ranges of 300–550 °C can be simulated tuning the transport parameters involved. A parametric study has been performed to reduce the degrees of freedom and to determine the error caused in the simulation due to the uncertainty in experimental input data. The information obtained is essential for the experimental benchmarking. The Tritium Permeation Percentage (TPP) is an output calculated parameter with low variations between 2 and 6% along the whole experimental time easy to compare (730 Full Power Days for LIBRETTO-4 and 520 for 5). Tritium transport parameter ranges verifying this output are defined herein.

Tritium enrichment from aqueous solutions using cryosublimation of mono- and polysaccharides

International Nuclear Information System (INIS)

Wierczinski, B.; Muellen, G.; Rosenhauer, S.

2008-01-01

Cryosublimation is one technique, which allows the accumulation of tritium from aqueous solutions using certain chemical compounds. After studying several inorganic compounds such as zeolites and metal salts, as well as some humic substances, we have now investigated several mono- and polysaccharides, such as glucose, maltose, galactose, starch, agar, and gelatine. Except for starch all of the above mentioned compounds showed a clear enrichment of tritium. The highest value was reached for Agartine, which gave an enrichment factor of 6.2. Since mono- and polysaccharides form weak hydrogen bonds, these results prove again our theory that tritium is preferably accumulated in exchangeable hydrogen bonds. (author)

Effects of ultraviolet irradiation on bonding strength between Co-Cr alloy and citric acid-crosslinked gelatin matrix.

Science.gov (United States)

Inoue, Motoki; Sasaki, Makoto; Katada, Yasuyuki; Taguchi, Tetsushi

2014-02-01

Novel techniques for creating a strong bond between polymeric matrices and biometals are required. We immobilized polymeric matrices on the surface of biometal for drug-eluting stents through covalent bond. We performed to improve the bonding strength between a cobalt-chromium alloy and a citric acid-crosslinked gelatin matrix by ultraviolet irradiation on the surface of cobalt-chromium alloy. The ultraviolet irradiation effectively generated hydroxyl groups on the surface of the alloy. The bonding strength between the gelatin matrix and the alloy before ultraviolet irradiation was 0.38 ± 0.02 MPa, whereas it increased to 0.48 ± 0.02 MPa after ultraviolet irradiation. Surface analysis showed that the citric acid derivatives occurred on the surface of the cobalt-chromium alloy through ester bond. Therefore, ester bond formation between the citric acid derivatives active esters and the hydroxyl groups on the cobalt-chromium alloy contributed to the enhanced bonding strength. Ultraviolet irradiation and subsequent immobilization of a gelatin matrix using citric acid derivatives is thus an effective way to functionalize biometal surfaces.

Impact analysis of the time trend of TBR and irradiation damage assessment of HCSB blanket for CFETR

Energy Technology Data Exchange (ETDEWEB)

Zeng, Qin, E-mail: zengqin@ustc.edu.cn; Chen, Hongli; Lv, Zhongliang; Pan, Lei; Zhang, Haoran; Shi, Wei

2017-01-15

Chinese Fusion Engineering Testing Reactor (CFETR) is a test tokamak reactor to bridge the gap between ITER and future fusion power plants and to demonstrate generation of fusion power in China. In fusion power plants, tritium is generated from the reaction of neutron and Lithium. One of the missions of CFETR is the full cycle of tritium self-sufficiency. For the mission, a Helium Cooled Solid Breeder blanket (HCSB) was proposed for CFETR and its conceptual design has been carried out. In order to assess the capacity of the tritium breeding and irradiation damage of first wall of the HCSB blanket during the 8 years’ engineering test stage, this paper presents the time trend of TBR analysis and irradiation damage assessment of HCSB blanket based on the three-dimensional (3D) neutronics model which is created by McCad. In the 3D neutronics model, the outboard blanket on equatorial plane is described based on the detailed 3D engineering model. The calculations were performed by MCNP and FISPACT with FENDL/2.1 data library. The impact analysis of the thickness of coolant plates (CP) and the structural material content in CPs to the TBR is assessment.

Liquid Wall Options for Tritium-Lean Fast Ignition Inertial Fusion Energy Power Plants

International Nuclear Information System (INIS)

Reyes, S.; Schmitt, R.C.; Latkowski, J.F.; Durbin, S.G.' Sanz, J.

2002-01-01

In an inertial fusion energy (FE) thick-liquid chamber design such as HYLEE-II, a molten-salt is used to attenuate neutrons and protect the chamber structures from radiation damage. In the case of a fast ignition inertial fusion system, advanced targets have been proposed that may be self-sufficient in terms of tritium breeding (i.e., the amount of tritium bred in target exceeds the amount burned). This aspect allows for greater freedom when selecting a liquid for the protective blanket, given that lithium-bearing compounds are no longer required. The present work assesses the characteristics of many single, binary, and ternary molten-salts using the NIST Properties of Molten Salts Database. As an initial screening, salts were evaluated for their safety and environmental (S and E) characteristics, which included an assessment of waste disposal rating, contact dose, and radioactive afterheat. Salts that passed the S and E criteria were then evaluated for required pumping power. The pumping power was calculated using three components: velocity head losses, frictional losses, and lifting power. The results of the assessment are used to identify those molten-salts that are suitable for potential liquid-chamber fast-ignition IFE concepts, from both the S and E and pumping power perspective. Recommendations for further analysis are also made

TRIO-01 experiment: in-situ tritium-recovery results

International Nuclear Information System (INIS)

Clemmer, R.G.; Finn, P.A.; Billone, M.C.

1983-08-01

The TRIO-01 experiment is a test of in-situ tritium recovery from γ-LiAlO 2 with test conditions chosen to simulate those anticipated in fusion power reactors. A status report is presented which describes qualitatively the results observed during the irradiation phase of the experiment. Both the rate of tritium release and the chemical forms of tritium were measured using a helium sweep gas which flowed past the breeder material to a gas analysis system

TRIO-01 experiment: in-situ tritium recovery results

International Nuclear Information System (INIS)

Clemmer, R.G.; Finn, P.A.; Billone, M.C.

1983-10-01

The TRIO-01 experiment is a test of in-situ tritium recovery from γ-LiAlO 2 with test conditions chosen to simulate those anticipated in fusion power reactors. A status report is presented which describes qualitatively the results observed during the irradiation phase of the experiment. Both the rate of tritium release and the chemical forms of tritium were measured using a helium sweep gas which flowed past the breeder material to a gas analysis system

Tritium loss in molten flibe systems

Energy Technology Data Exchange (ETDEWEB)

Longhurst, G.R.; Anderl, R.A. [Idaho National Eng. and Environ. Lab., Idaho Falls, ID (United States); Scott Willms, R. [Los Alamos National Lab., NM (United States)

2000-04-01

An emerging issue relative to beryllium technology in fusion involves tritium interactions with molten beryllium-bearing salts. Innovative designs for fusion reactors, both magnetic and inertially confined, feature the molten salt mixture 2LiF.BeF{sub 2}, commonly called Flibe, as a tritium breeder and coolant. Tritium is bred in the Flibe as neutrons from the plasma are absorbed by Li atoms, which then transmute to tritium and helium. Transmutation of tritium from Be also occurs. Among the issues to be resolved for such coolant systems is the potential loss of tritium from the Flibe coolant to the walls of the system, particularly through heat exchanger tubes, and from there into secondary coolants or working fluids and the environment. Effectively removing tritium from Flibe in clean-up units is also important. In quiescent or low Reynolds number flow, tritium movement through Flibe is governed by diffusion. For Flibe in turbulent flow, as in heat exchanger tubes, transport is by turbulent mixing, and the same flow conditions and structural design features that maximize heat transfer to the heat exchanger walls will enhance the transport of tritium to those same surfaces. Analyses have been performed to estimate the fractional loss of tritium through heat exchanger tubes and release rates from Flibe droplets in vacuum disengagers in molten Flibe systems. The calculations suggest unacceptably large losses of tritium through heat exchanger tubes. The gravity of the implications of these estimates calls for experimental verification to determine if tritium losses through molten Flibe heat exchangers or other Flibe systems can really be so high and whether vacuum disengagers will really work. There is also a need for better information on evolution of tritium from Flibe droplets in a vacuum. Several experiments are presently being planned to address these issues and are discussed. These include experiments to induce tritium in Flibe using spontaneous fission neutrons

Tritium loss in molten flibe systems

International Nuclear Information System (INIS)

Longhurst, G.R.; Anderl, R.A.; Scott Willms, R.

2000-01-01

An emerging issue relative to beryllium technology in fusion involves tritium interactions with molten beryllium-bearing salts. Innovative designs for fusion reactors, both magnetic and inertially confined, feature the molten salt mixture 2LiF.BeF 2 , commonly called Flibe, as a tritium breeder and coolant. Tritium is bred in the Flibe as neutrons from the plasma are absorbed by Li atoms, which then transmute to tritium and helium. Transmutation of tritium from Be also occurs. Among the issues to be resolved for such coolant systems is the potential loss of tritium from the Flibe coolant to the walls of the system, particularly through heat exchanger tubes, and from there into secondary coolants or working fluids and the environment. Effectively removing tritium from Flibe in clean-up units is also important. In quiescent or low Reynolds number flow, tritium movement through Flibe is governed by diffusion. For Flibe in turbulent flow, as in heat exchanger tubes, transport is by turbulent mixing, and the same flow conditions and structural design features that maximize heat transfer to the heat exchanger walls will enhance the transport of tritium to those same surfaces. Analyses have been performed to estimate the fractional loss of tritium through heat exchanger tubes and release rates from Flibe droplets in vacuum disengagers in molten Flibe systems. The calculations suggest unacceptably large losses of tritium through heat exchanger tubes. The gravity of the implications of these estimates calls for experimental verification to determine if tritium losses through molten Flibe heat exchangers or other Flibe systems can really be so high and whether vacuum disengagers will really work. There is also a need for better information on evolution of tritium from Flibe droplets in a vacuum. Several experiments are presently being planned to address these issues and are discussed. These include experiments to induce tritium in Flibe using spontaneous fission neutrons

Dissolution behavior of lithium compounds in ethanol

Directory of Open Access Journals (Sweden)

Tomohiro Furukawa

2016-12-01

Full Text Available In order to exchange the components which received irradiation damage during the operation at the International Fusion Materials Irradiation Facility, the adhered lithium, which is partially converted to lithium compounds such as lithium oxide and lithium hydroxide, should be removed from the components. In this study, the dissolution experiments of lithium compounds (lithium nitride, lithium hydroxide, and lithium oxide were performed in a candidate solvent, allowing the clarification of time and temperature dependence. Based on the results, a cleaning procedure for adhered lithium on the inner surface of the components was proposed.

Effect of Pre-Irradiation Annealing and Laser Modification on the Formation of Radiation-Induced Surface Color Centers in Lithium Fluoride

Science.gov (United States)

Voitovich, A. P.; Kalinov, V. S.; Novikov, A. N.; Radkevich, A. V.; Runets, L. P.; Stupak, A. P.; Tarasenko, N. V.

2017-01-01

It is shown that surface color centers of the same type are formed in the surface layer and in regions with damaged crystal structure inside crystalline lithium fluoride after γ-irradiation. Results are presented from a study of the effect of pre-irradiation annealing on the efficiency with which surface centers are formed in lithium fluoride nanocrystals. Raising the temperature for pre-irradiation annealing from room temperature to 250°C leads to a substantial reduction in the efficiency with which these centers are created. Surface color centers are not detected after γ-irradiation for pre-irradiation annealing temperatures of 300°C and above. Adsorption of atmospheric gases on the crystal surface cannot be regarded as a necessary condition for the formation of radiation-induced surface centers.

Shear Bond Strength of Resin Buttons to Lithium Disilicate and Leucite Reinforced Feldspathic Restorations

Science.gov (United States)

2016-05-01

utilizing enamel bonding procedures. These fixed orthodontic appliances are the gold standard in orthodontic treatment and can be used to correct... enamel of teeth. When this same procedure needs to be done on a restorative material such as lithium disilicate, or leucite reinforced feldspathic...toughness from its crystal size and orientation which causes cracks to deflect instead of propagate. The second material being tested, IPS Empress

Liquid Li-Pb-Bi, a new tritium breeder

International Nuclear Information System (INIS)

Rogers, A.G.; Benedict, B.L.; Clemmer, R.G.

1981-01-01

In light of their potential utility as tritium breeder-blanket materials, a study was conducted to identify and characterize low-melting phases in the lithium-lead-bismuth system. It is found that a low-melting ternary phase field did in fact exist, e.g., compositions with less than or equal to 20 atom percent lithium and Pb/Bi = 0.773 melted at or below 140 0 C. In addition, the qualitative reactivity of Li-Bi-Pb alloys with water was tested, and although minimal evidence of exothermic chemical reaction was observed, a physical vapor explosion did occur in one of the tests

Effects of irradiation on four solid breeder materials

International Nuclear Information System (INIS)

Hollenberg, G.W.

1984-01-01

The tritium breeding material with the highest lithium atom density, Li 2 O has been observed to incur significant swelling (>4%) under fast reactor irradiation. Such swelling, if unrestrained leads to either unacceptable, induced-strains in adjacent structural material or undesirable design compromises. Fortunately, however, Li 2 O deforms at low temperatures so that swelling strains may be internally accommodated. Laboratory dilational creep experiments were conducted on unirraciated Li 2 O between 500 and 700 0 C in order to provide data for structural analysis of in-reactor experiments and blanket design studies. A densification model agreed with most of the available data. 15 refs

Fabrication of cermet bearings for the control system of a high temperature lithium cooled nuclear reactor

Science.gov (United States)

Yacobucci, H. G.; Heestand, R. L.; Kizer, D. E.

1973-01-01

The techniques used to fabricate cermet bearings for the fueled control drums of a liquid metal cooled reference-design reactor concept are presented. The bearings were designed for operation in lithium for as long as 5 years at temperatures to 1205 C. Two sets of bearings were fabricated from a hafnium carbide - 8-wt. % molybdenum - 2-wt. % niobium carbide cermet, and two sets were fabricated from a hafnium nitride - 10-wt. % tungsten cermet. Procedures were developed for synthesizing the material in high purity inert-atmosphere glove boxes to minimize oxygen content in order to enhance corrosion resistance. Techniques were developed for pressing cylindrical billets to conserve materials and to reduce machining requirements. Finishing was accomplished by a combination of diamond grinding, electrodischarge machining, and diamond lapping. Samples were characterized in respect to composition, impurity level, lattice parameter, microstructure and density.

Linear accelerator for production of tritium: Physics design challenges

Energy Technology Data Exchange (ETDEWEB)

Wangler, T.P.; Lawrence, G.P.; Bhatia, T.S.; Billen, J.H.; Chan, K.C.D.; Garnett, R.W.; Guy, F.W.; Liska, D.; Nath, S.; Neuschaefer, G.; Shubaly, M.

1990-01-01

In the summer of 1989, a collaboration between Los Alamos National Laboratory and Brookhaven National Laboratory conducted a study to establish a reference design of a facility for accelerator production of tritium (APT). The APT concept is that of a neutron-spallation source, which is based on the use of high-energy protons to bombard lead nuclei, resulting in the production of large quantities of neutrons. Neutrons from the lead are captured by lithium to produce tritium. This paper describes the design of a 1.6-GeV, 250-mA proton cw linear accelerator for APT.

Hydrogen extraction from liquid lithium-lead alloy by bubbling with rotational jet nozzle

International Nuclear Information System (INIS)

Xie Bo; Yang Tongzai; Guan Rui; Weng Kuiping

2010-01-01

The technology of tritium extraction from lithium-lead alloy has been simulated, hydrogen extraction from lithium-lead alloy by bubbling with rotational jet nozzle being used to simulate tritium in the study based on the introduction of fluid dynamics to establish algebraic model. The results show that the higher than lithium-lead melting temperature, the higher cumulative hydrogen extraction efficiency, and gas holdup of bubble column is little affected by the impeller diameter. Gas holdup when using small aperture is slightly higher when using large aperture only at a high helium flow rate, but the smaller the aperture, the greater the bubble surface area, and a marked increase in intensity of flow circulation for liquid lithium-lead with the increase of helium flow rate, hydrogen extraction rate increases too. Moreover, influence of the jet rotational velocity on hydrogen extraction is limited. (authors)

Release of gaseous tritium during reprocessing

International Nuclear Information System (INIS)

Bruecher, H.; Hartmann, K.

1983-01-01

About 50% of the tritium put through an LWR reprocessing plant is obtained as tritium-bearing water, HTO. Gaseous tritium, HT has a radiotoxicity which is by 4 orders of magnitude lower than that of HTO. A possibility for the removal of HTO could therefore be its conversion into the gas phase with subsequent emission of the HT into the atmosphere. However, model computations which are, in part, supported by experimental data reveal that the radiation exposure caused by HT release is only by about one order of magnitude below that caused by HTO. This is being attributed to the relatively quick reoxidation of HT by soil bacteria. Two alternatives for producing HT from HTO (electrolysis; voloxidation with subsequent electrolysis) are presented and compared with the reference process of deep-well injection of HTO. The authors come to the conclusion that tritium removal by HT release into the atmosphere cannot be recommended at present under either radiological or economic aspects. (orig.) [de

A 2D Finite Element Modelling of Tritium Permeation Through Cooling Plates for The HCLL DEMO Blanket Module

International Nuclear Information System (INIS)

Gabriel, F.; Escuriol, Y.; Dabbene, F.; Salavy, J.F.; Giancarli, L.; Gastaldi, O.

2006-01-01

As the Tritium self sufficiency is one of the major challenges for fusion reactor, breeding blankets represent one of the major technological breakthroughs required from passing from ITER to the next step reactor, usually called DEMO. One of the two blanket concepts developed in the EU is the Helium Cooled Lithium Lead (HCLL) blanket which uses the eutectic Pb-15.7Li metal liquid as both breeder and neutron multiplier. The structures, made of EUROFER, a low activation ferritic martensitic steel, are cooled by pressurized helium at 8 MPa and inlet/outlet temperature 300/500 o C. In this concept, the LiPb is fed from the top of the blanket and distributed in parallel vertical channels among pairs of cells (one cell for the radial movement towards the plasma, the other for the return). The liquid metal fills the in-box volume and is slowly re-circulated (few mm per seconds) to remove the produced tritium. In this paper, a local finite element modelling of the tritium permeation rate through the HCLL breeder unit cooling plates is presented. The tritium concentration in the helium circuit and remaining in the lithium lead circuit are evaluated by solving partial differential equations governing the tritium concentration balance, the thermal field and the lithium lead velocity field for a simplified 2D geometrical representation of the breeder unit. This allows estimating the sensitivity effect of coupling these different equations in order to deduce a relevant but simplified modelling for tritium permeation. This is to compare with tritium inventories studies, were the tritium permeation rate is estimated using simplified analytical modelling which generally leads to over estimate the tritium permeation rate to the coolant and so has strong influence on the coolant purification plant design. The finite element modelling performed shows that the Tritium permeation is considerable lower than the one obtained in previous estimations where nominal values of the governing

Irradiation-induced modification of the material parameters in magnesium-doped lithium niobate

International Nuclear Information System (INIS)

Jentjens, Lena

2010-01-01

In the framework of this thesis the material properties of lithium niobate are directedly influenced by the irradiation with 3 He ions with an energy of 40 MeV. In the first part the irradiation-induced material changes are intensively studied. Long-time stable changes of the refractive index are measured in the range of up to 6.10 -3 , which depend on the radiation dose and exhibit until now no saturation behaviour. Accompanied is this change by an also dose-dependent deformation as well as a brownish change of color of the crystals. Furthermore a by several orders of magnitude increased electrical dark- and photoconductivity, which depends on the ion dose and exhibits until now also no saturation behaviour. An effect independent on the ion dose is the reduction of the coercive field strength by about 10%. Furthermore it was stated the quantity of the effects not only depends on the absolute dose, but also on the irradiation direction in view of the crystallographic c-axis. The second part of this thesis deals with the generation of microscopic structures in lithium niobate. By an ion microbeam respectively a shiftable slit aperture the fabrication of refractive-index gratings is pursued. Grating with periodicity lengths in the range of 12-160 μm could until now be detected and promise in comparison with photorefractive gratings the advance of larger stability.

Microstructure in HIP-bonded F82H steel and its mechanical properties after irradiation

International Nuclear Information System (INIS)

Furuya, K.; Wakai, E.

2006-01-01

A first primary blanket structure is composed of the low-activation steel, e.g. F82H, and is fabricated by using a solid hot isostatic pressing (HIP) bonding method. A partial mock-up of such a blanket structure was successfully fabricated. The tensile specimen including HIP-bonded region possessed a sufficient strength and elongation under a non-irradiated condition as reported in our previous studies. In this study, the microstructures of HIP interface before irradiation were observed by a TEM, and the effects of irradiation on mechanical properties of the HIP-bonded region were also examined. TEM observation and elemental analysis of the HIP-bonded region before the irradiation were performed by using a FE-TEM of HF-2000 equipped with EDX spectroscopy. Tensile specimens (type SS-3) were prepared from a HIP-bonded region and a plate region of the mock-up block. Neutron irradiation was performed up to about 1.9 dpa at about 523 K in JMTR. After the irradiation, tensile test was performed at temperatures of 295 and 523 K. After the tensile test, OM observation at the rupture region and SEM observation at the fracture surface were conducted, respectively. TEM observation and analytical results revealed that the HIP interface possessed many precipitates, and enriched peak spectrum of chromium was detected from the precipitates. In addition, aspect of the spectrum was qualitatively equivalent to that of M23C6 in grain boundaries of F82H steel. In result, the HIP boundary has many M23C6 which were generally seen in grain boundaries of F82H steel, and it can be mentioned that the HIP interface is, in this sense, a new grain boundary. Obvious HIP boundary was seen at rupture region of tensile specimens sampled from the HIP-bonded region, by the macroscopic observation. It means that rupture do not occur in the HIP interface. In result, it can be mentioned that bondability of the HIP interfaces is kept under the irradiation and testing conditions. The strength and

Tritium Waste Treatment System component failure data analysis from June 18, 1984--December 31, 1989

International Nuclear Information System (INIS)

Cadwallader, L.C.; Stolpe Gavett, M.A.

1990-09-01

This document gives the failure rates for the major tritium-bearing components in the Tritium Waste Treatment System at the Tritium Systems Test Assembly, which is a fusion research and technology facility at the Los Alamos National Laboratory. The failure reports, component populations, and operating demands/hours are given in this report, and sample calculations for binomial demand failure rates and poisson hourly failure rates are given in the appendices. The failure rates for tritium-bearing components were on the order of the screening failure rate values suggested for fusion reliability and risk analyses. More effort should be directed toward collecting and analyzing fusion component failure data, since accurate failure rates are necessary to refine reliability and risk analyses. 15 refs., 4 figs., 4 tabs

CTR related tritium research at LASL

International Nuclear Information System (INIS)

Anderson, J.L.; Carstens, D.H.W.; Alire, R.M.

1975-01-01

The solubility and diffusion coefficients of H 2 in Li contained in a cylinder of Nb/1 percent Zr were measured in the temperature range 805-905 0 C at a pressure of 575 Pa. Appropriate corrections for the solubility of H 2 in Nb/1 percent Zr were made. As expected, a finite solid cylinder diffusion model adequately delineates the time-dependent consumption of H 2 in Li. The diffusion coefficient was found to vary from 3.88 x 10 -5 to 6.92 x 10 -5 cm 2 /sec and the activation energy was estimated to be 14.7 kcal/mole. The use of low melting eutectic mixtures containing Y, La, and Ce for extracting tritium from molten lithium is being investigated. Eutectic mixtures being investigated include the 16 percent in La, 12 percent Fe in Ce and 16 percent Co in Ce. At 875 0 K the molar distribution coefficients for tritium between these eutectic mixtures and lithium are less than or equal to 100. The temperature coefficients for these distributions are also being investigated. The pressure-composition-temperature diagram for the La 5 Ni-deuterium system is being studied. A ΔH of --39.7 kcal/mole D 2 was measured for the composition D/La 1.5. (auth)

Deuterium migration in nuclear graphite: consequences for the behavior of tritium in Gas Cooled Reactors and for the decontamination of irradiated graphite waste

International Nuclear Information System (INIS)

Le-Guillou, Mael

2014-01-01

In France, 23 000 t of irradiated graphite that will be generated by the decommissioning of the first generation Uranium Naturel-Graphite-Gaz (UNGG) nuclear reactors are waiting for a long term management solution. This work focuses on the behavior of tritium, which is one of the main contributors to the radiological inventory of graphite waste after reactor shutdown. In order to anticipate tritium release during dismantling or waste management, it is mandatory to collect data on its migration, location and inventory. Our study is based on the simulation of tritium by implantation of approximately 3 at. % of deuterium up to around 3 μm in a virgin nuclear graphite. This material was then annealed up to 300 h and 1300 C in inert atmosphere, UNGG coolant gas and humid gas, aiming to reproduce thermal conditions close to those encountered in reactor and during waste management operations. The deuterium profiles and spatial distribution were analyzed using the nuclear reaction 2 H( 3 He,p) 4 He. The main results evidence a thermal release of implanted deuterium occurring essentially through three regimes controlled by the detrapping of atomic deuterium located in superficial or interstitial sites. The extrapolation of our data to tritium suggests that its purely thermal release during reactor operations may have been lower than 30 % and would be located close to the graphite free surfaces. Consequently, most of the tritium inventory after reactor shutdown could be trapped deeply within the irradiated graphite structure. Decontamination of graphite waste should then require temperatures higher than 1300 C, and would be more efficient in dry inert gas than in humid gas. (author)

Present status of tritium research activities at universities in Japan

International Nuclear Information System (INIS)

Kawamura, K.

1983-01-01

The behaviours of tritium towards various materials are very similar to those of hydrogen, since tritium is one of the hydrogen isotope. In addition to those properties, tritium shows the radiochemical and radiological reactivities due to an emitted #betta#-ray. The permeability of tritium through various materials is the example of the former. The formation of tritiated methane in tritium stored in stainless steel vessels and the increase of helium content in tritium-bearing metallic materials are the examples of the latter. For these reasons, advanced and somewhat more complicated techniques are required for handling tritium. After the Ministry of Education, Science and Culture (MOE) made an appropriation on Grant-in-Aid for Fusion Research in 1975 year's budget, development of tritium handling technology for fusion reactors have been actively pursued. The specific experiments to be embodied in present research activities are: 1. Measurements of tritium permeation rate through various materials. 2. Fundamental studies on tritium containment materials. 3. Fundamental studies of tritium waste treatment and storage. In this paper, the works achieved under the above research activities are described and some results obtained from experiments are reported. (author)

γ-irradiated crystalline sugars and amino acids: A chemical analysis

International Nuclear Information System (INIS)

Gejvall, T.

1975-01-01

Crystalline sugars and amino acids were irradiated at room temperature in a 60 Co γ-source at a dose rate ranging from 2 to 3x10 19 eV/g per hour. The investigation has geen performed to broaden the knowledge about what happens to food at irradiation preservation. The total degradation and the role of the glycosidic bond were investigated in some carbonhydrates. Transfer reactions of tritium constitute another specific problem which has been treated. Several components are formed in the crystalline amino acids, and a new gas chromatographic method was developed for analysis of amines in degraded material. (K.K)

Nuclear irradiation parameters of beryllium under fusion, fission and IFMIF irradiation conditions

International Nuclear Information System (INIS)

Fischer, U.; Chen, Y.; Leichtle, D.; Simakov, S.; Moeslang, A.; Vladimirov, P.

2004-01-01

A computational analysis is presented of the nuclear irradiation parameters for Beryllium under irradiation in typical neutron environments of fission and fusion reactors, and of the presently designed intense fusion neutron source IFMIF. The analysis shows that dpa and Tritium production rates at fusion relevant levels can be achieved with existing high flux fission reactors while the achievable Helium production is too low. The resulting He-Tritium and He/dpa ratios do not meet typical fusion irradiation conditions. Irradiation simulations in the medium flux test modules of the IFMIF neutron source facility were shown to be more suitable to match fusion typical irradiation conditions. To achieve sufficiently high production rates it is suggested to remove the creep-fatigue testing machine together with the W spectra shifter plate and move the tritium release module upstream towards the high flux test module. (author)

Control of the tritium path in process heat HTR's

International Nuclear Information System (INIS)

Kirch, N.; Scheidler, G.

1985-01-01

Nuclear Process Heat plant converting fossil fuels into liquid or gaseous secondary energy carriers generate tritium by several nuclear reactions. Control of the tritium path through the walls of the heat exchanger is highly important to meet regulatory requirements on the acceptable contamination in the product gas or liquid. Therefore, significant effort in the project 'Prototypanlage Nukleare Prozesswaerme' was put not only into generating a data base, but also into means of reducing tritium generation and permeation. Clean graphites with lithium impurities in the ppb level provide a low tritium source term. Realistic modeling of graphite retention and special helium purification systems are essentials. The main barrier to tritium permeation are heat exchanger walls requiring detailed characterization of in-situ surface layers. Studies to optimize the water/steam mass flow in the conversion process offer possibilities for further tritium retention. Progress can be demonstrated as follows: In 1980, between 2 and 8 Bq tritium per gram of product were predicted based on available data and even higher concentrations during startup. However, present day validated code predictions are below required 0.5 Bq/g equilibrium concentration level. During transients - particularly startup - this limit cannot be guaranteed as yet, but further retention potential is being offered by tritium gettering or filtering. An expected increase of the German regulatory requirement to 5 Bq/g will easily be met by present plant design under all operational conditions. (author)

Tritium system for a tokamak reactor with a self-pumped limiter

International Nuclear Information System (INIS)

Hassanein, A.M.; Sze, D.K.

1986-01-01

Benefits of the self-pumping system are the elimination of vacuum ducts, pumps, and penetration shielding (except for a very small startup system), and the reduction of tritium recycle and refueling. In addition, a self-pumped system may perform better and last longer than alternative systems such as a pumped limiter. The reference case here is a self-cooled lithium/vanadium blanket with a first wall/limiter. This concept combines the functions of first wall and limiter into a single first-wall structure. The wall is shaped in accordance with the outermost plasma flux surface. Trapping material is added to the plasma scrape-off or edge region where it is transported to the wall. The entire wall area is used for helium trapping. The tritium inventory, tritium permeation rate, and plasma protium concentration for the vanadium wall as a function of the number of years of operation are calculated. The tritium inventory is acceptable, the protium concentration in the plasma is acceptably small, and the tritium permeation rate is moderate. At the start of operation, it is equal to about five times the tritium burnup rate. This tritium will enter the coolant and the cost of the blanket tritium recovery system will be higher

Sublethal effects of tritium on aquatic systems, effects of low-level chronic irradiation on embryonic development, effects of beryllium and lithium on aquatic systems, and teratogenic effects of low-level magnetic fields

International Nuclear Information System (INIS)

Strand, J.A.; Roesijadi, G.; Emery, R.M.

1978-01-01

It is conceivable, and possible, that with increasing applications of nuclear energy, greater quantities of potentially harmful radionuclides will be released to the environment. This may be particularly true for advanced reactor designs such as the fusion reactor where radionuclides, principally tritium, may be expected to escape from the plant both in gaseous and liquid effluents in quantities significantly greater than for present PWR or BWR designs. Foreseeing such contingencies, the research programs described herein are in response to the need to measure the potential radiation effects of tritium releases on individuals, and ultimately populations and biotic communities. As a first approach, our efforts are directed to determine effects of low-level chronic exposures on developing embryo and larval stages, clearly the most radiosensitive. The anticipated increase in the release of beryllium and lithium from mining, refining, and fabrication of materials used during construction of fusion reactors has also caused concern as to potential adverse effects on the environment. Accordingly, FY-78 fusion related research will include efforts to study the metabolism of each metal in the living organism, and to determine at what levels toxicity may be expected. Fusion related research will also include preliminary experiments on the effects of low-level magnetic fields. It is conceivable that magnetic fields of 70 to 450 gauss will be encountered by attendant personnel working in the transport and hot cell areas of fusion reactors. Also, those personnel assigned to the areas immediately surrounding the reactor may be exposed

Reduced cost design of liquid lithium target for international fusion material irradiation facility (IFMIF)

International Nuclear Information System (INIS)

Nakamura, Hiroo; Ida, Mizuho; Sugimoto, Masayoshi; Takeuchi, Hiroshi; Yutani, Toshiaki

2001-01-01

The International Fusion Materials Irradiation Facility (IFMIF) is being jointly planned to provide an accelerator-based D-Li neutron source to produce intense high energy neutrons (2 MW/m 2 ) up to 200 dpa and a sufficient irradiation volume (500 cm 3 ) for testing the candidate materials and components up to about a full lifetime of their anticipated use in ITER and DEMO. To realize such a condition, 40 MeV deuteron beam with a current of 250 mA is injected into high speed liquid lithium flow with a speed of 20 m/s. Following Conceptual Design Activity (1995-1998), a design study with focus on cost reduction without changing its original mission has been done in 1999. The following major changes to the CAD target design have been considered in the study and included in the new design: i) number of the Li target has been changed from 2 to 1, ii) spare of impurity traps of the Li loop was removed although the spare will be stored in a laboratory for quick exchange, iii) building volume was reduced via design changes in lithium loop length. This paper describes the reduced cost design of the lithium target system and recent status of Key Element Technology activities. (author)

Status of advanced tritium breeder development for DEMO in the broader approach activities in Japan

International Nuclear Information System (INIS)

Hoshino, Tsuyoshi; Oikawa, Fumiaki; Nishitani, Takeo

2010-01-01

DEMO reactors require ' 6 Li-enriched ceramic tritium breeders' which have high tritium breeding ratios (TBRs) in the blanket designs of both EU and JA. Both parties have been promoting the development of fabrication technologies of Li 2 TiO 3 pebbles and of Li 4 SiO 4 pebbles including the reprocessing. However, the fabrication techniques of tritium breeders pebbles have not been established for large quantities. Therefore, these parties launch a collaborative project on scaleable and reliable production routes of advanced tritium breeders. In addition, this project aims to develop fabrication techniques allowing effective reprocessing of 6 Li. The development of the production and 6 Li reprocessing techniques includes preliminary fabrication tests of breeder pebbles, reprocessing of lithium, and suitable out-of-pile characterizations. The R and D on the fabrication technologies of the advanced tritium breeders and the characterization of developed materials has been started between the EU and Japan in the DEMO R and D of the International Fusion Energy Research Centre (IFERC) project as a part of the Broader Approach activities from 2007 to 2016. The equipment for production of advanced breeder pebbles is planned will be installed in the DEMO R and D building at Rokkasho, Japan. The design work in this facility was carried out. The specifications of the pebble production apparatuses and related equipment in this facility were fixed, and the basic data of these apparatuses was obtained. In this design work, the preliminary investigations of the dissolution and purification process of tritium breeders were carried out. From the results of the preliminary investigations, lithium resources of 90% above were recovered by the aqueous dissolving methods using HNO 3 and H 2 O 2 . The removal efficiency of 60 Co by the addition in the dissolved solutions of lithium ceramics were 97-99.9% above using activated carbon impregnated with 8-hydroxyquinolinol. In this report

Bond strength of dental adhesive systems irradiated with ionizing radiation.

Science.gov (United States)

Dibo da Cruz, Adriana; Goncalves, Luciano de Souza; Rastelli, Alessandra Nara de Souza; Correr-Sobrinho, Lorenco; Bagnato, Vanderlei Salvador; Boscolo, Frab Norberto

2010-04-01

The aim of the present paper was to determine the effect of different types of ionizing radiation on the bond strength of three different dentin adhesive systems. One hundred twenty specimens of 60 human teeth (protocol number: 032/2007) sectioned mesiodistally were divided into 3 groups according to the adhesives systems used: SB (Adper Single Bond Plus), CB (Clearfil SE Bond) and AP (Adper Prompt Self-Etch). The adhesives were applied on dentin and photo-activated using LED (Lec 1000, MMoptics, 1000 mW/cm2). Customized elastomer molds (0.5 mm thickness) with three orifices of 1.2 mm diameter were placed onto the bonding areas and filled with composite resin (Filtek Z-250), which was photo-activated for 20 s. Each group was subdivided into 4 subgroups for application of the different types of ionizing radiation: ultraviolet radiation (UV), diagnostic x-ray radiation (DX), therapeutic x-ray radiation (TX) and without irradiation (control group, CG). Microshear tests were carried out (Instron, model 4411), and afterwards the modes of failure were evaluated by optical and scanning electron microscope and classified using 5 scores: adhesive failure, mixed failures with 3 significance levels, and cohesive failure. The results of the shear bond strength test were submitted to ANOVA with Tukey's test and Dunnett's test, and the data from the failure pattern evaluation were analyzed with the Mann Whitney test (p = 0.05). No change in bond strength of CB and AP was observed after application of the different radiation types, only SB showed increase in bond strength after UV (p = 0.0267) irradiation. The UV also changed the failure patterns of SB (p = 0.0001). The radio-induced changes did not cause degradation of the restorations, which means that they can be exposed to these types of ionizing radiation without weakening the bond strength.

Immuno-enhancement in tumor-bearing mice induced by whole body X-irradiation with 75 mGy

International Nuclear Information System (INIS)

Zhang Ying; Li Xiuyi; Gong Shouliang; Liu Shuzheng

2000-01-01

Objective: In present study the authors observed the effect of whole body irradiation (WBI) with 75 mGy X-rays on the immune function of tumor-bearing mice. Methods: Lewis lung carcinoma cells were implanted into the right thigh muscle of C57BL/6J mice. Ten days after tumor implantation, the tumor-bearing mice were administrated with 75 mGy X-rays WBI, then the mice were sacrificed 18 h after irradiation to detect the immune parameters including the spontaneous proliferation of thymocytes, the proliferative response of splenocytes to ConA and LPS, the cytotoxic activities of specific cytotoxic lymphocytes (CTL) and natural killer cells (NK), as well as lymphokine activated killer cells (LAK) in spleen. The methods the authors used were 3 H-TdR incorporation or release assay. Results: the immune parameters of exposed tumor-bearing mice were much higher than those of sham-irradiated tumor-bearing mice (P<0.01). Conclusion: These results suggested that low dose radiation (LDR) could enhance the immune function of tumor-bearing mice, which might be of practical significance in the prevention and therapy of cancer

Conceptual design of Tritium Extraction System for the European HCPB Test Blanket Module

International Nuclear Information System (INIS)

Ciampichetti, A.; Nitti, F.S.; Aiello, A.; Ricapito, I.; Liger, K.; Demange, D.; Sedano, L.; Moreno, C.; Succi, M.

2012-01-01

Highlights: ► HCPB (Helium Cooled Pebble Bed) Test Blanket Module (TBM) to be tested in ITER. ► Tritium extraction by gas purging, removal and transfer to the Tritium Plant. ► Conceptual design of TES and revision of the previous configuration. ► Main components: adsorption column, ZrCo getter beds and PERMCAT reactor. - Abstract: The HCPB (Helium Cooled Pebble Bed) Test Blanket Module (TBM), developed in EU to be tested in ITER, adopts a ceramic containing lithium as breeder material, beryllium as neutron multiplier and helium at 80 bar as primary coolant. In HCPB-TBM the main function of Tritium Extraction System (TES) is to extract tritium from the breeder by gas purging, to remove it from the purge gas and to route it to the ITER Tritium Plant for the final tritium processing. In this paper, starting from a revision of the so far reference process considered for HCPB-TES and considering a new modeling activity aimed to evaluate tritium concentration in purge gas, an updated conceptual design of TES is reported.

Tritium uptake in cultivated plants after short-term exposure to atmospheric tritium

International Nuclear Information System (INIS)

Diabate, S.; Strack, S.; Paunescu, N.

1998-01-01

The tritium behavior in crop plants is of particular interest for the prediction of doses to humans due to ingestion. Tritium is present in plants in two forms: tritium free water tissue (TWT) and organically bound tritium (OBT). The both forms are to be considered in models calculating the ingestion dose. Potato plants belong to the major food crops in many countries and were chosen as representatives of crops whose edible parts grow under ground. Green bean were chosen as representatives of vegetables relevant in human diet. This vegetable may be consumed as green pod and it may be conserved over a long period of time. Green bean and potato plants were exposed to tritiated water vapor in the atmosphere during their generative phase of development. The uptake of tritium and the conversion into organic matter was studied under laboratory conditions at two different light intensities. The tritium concentrations in plants were followed until harvest. In leaves, the tritium uptake into tissue water under night conditions was 5-6 times lower than under day-time conditions. The initial incorporation into organic matter under night conditions was 0.7% of the tissue water concentration in leaves of both plant species. However, under light irradiation, this value increased to only 1.8% in bean leaves and 0.9% in potato leaves, which indicates a participation of processes other than photosynthesis in tritium incorporation into organic material. Organically bound tritium (OBT) was translocated into pods and tubers which represented a high percentage of the total organically bound tritium at harvest. The behavior of total OBT in all plants under study showed that OBT, once generated, is lost very slowly until harvest, in particular when storage organs of plants were in their phase of development at the time of exposure. OBT is translocated into the storage organs which may be used in the human diet and thus may contribute to the ingestion dose for a long time after the

Tritium labeling of simple 7-membered ring compounds

International Nuclear Information System (INIS)

Hiltunen, J.; Peng, C.T.; Yang, Z.C.

1990-01-01

Seven-membered ring compounds, from cycloheptane to complex ring structures containing heteroatoms, substituents and fused phenyl rings, were labeled with tritium, using activated and adsorbed tritium. The 7-membered ring structures are generally stable towards reactions with tritium, which allows compounds like 1-benzosuberone, 1-aza-2-methoxy-1-cycloheptane, iminostilbene and clozapine to be labeled to reasonably high specific activities. The best method varies greatly from compound to compound. By optimizing the labeling conditions and use of efficient support exceptionally good results can be obtained. The Pd-on-alumina support gives consistently higher specific activity and less radioimpurity than other supports. Even molecules containing carbon-halogen bond and hydrogen bound to nitrogen can usually be labeled with tritium at stable positions and without dehalogenation. (author)

Effect of the self-pumped limiter concept on the tritium fuel cycle

International Nuclear Information System (INIS)

Finn, P.A.; Sze, D.K.; Hassanein, A.

1988-01-01

The self-pumped limiter concept was the impurity control system for the reactor in the Tokamak Power Systems Study (TPSS). The use of a self-pumped limiter had a major impact on the design of the tritium systems of the TPSS fusion reactor. The self-pumped limiter functions by depositing the helium ash under a layer of metal (vanadium). The majority of the hydrogen species are recycled at the plasma edge; a small fraction permeates to the blanket/coolant which was lithium in TPSS. Use of the self-pumped limiter results in the elimination of the plasma processing system. Thus, the blanket tritium processing system becomes the major tritium system. The main advantages achieved for the tritium systems with a self-pumped limiter are a reduction in the capital cost of tritium processing equipment as well as a reduction in building space, a reduced tritium inventory for processing and for reserve storage, an increase in the inherent safety of the fusion plant and an improvement in economics for a fusion world economy

Measurement of tritium in environment, (2)

International Nuclear Information System (INIS)

Chaya, Ikuo; Kagami, Tadaaki; Hamamura, Norikatsu

1975-01-01

In order to know the amount of natural tritium in environmental water and also to know the tendency of tritium concentration in surface water which is necessary for the measurement of ground water age, the tritium concentration in rain, river, and sea water in Aichi Prefecture were measured. In order to make the appropriate utilization of ground water such as city water and hot springs and to elucidate the effect of ground water utilization on ground subsidence, it is desirable to clarify the state of underground water-bearing strata, the flow direction and flow speed of ground water, and the change of ground water quality owing to the flow. As the means of knowing the flow speed of ground water, the age determination with tritium was carried out. The amount of tritium was determined by measuring the concentrated samples with a liquid scintillation counter. The tritium concentration in river was 1.7 times as much as that in rain water, and it is attributed to the time difference from raining to flowing in rivers. The tritium concentration in sea water was high at the estuary of Kiso River, and about a half of it in the other places. The water of the hot spring source in Nobi Plain is the old ground water soaked more than 20 years ago. The city water sources utilizing ground water shallower than 300 m use both new and old ground water. (Kako, I.)

Irradiation performance of helium-bonded uranium--plutonium carbide fuel elements

International Nuclear Information System (INIS)

Latimer, T.W.; Petty, R.L.; Kerrisk, J.F.; DeMuth, N.S.; Levine, P.J.; Boltax, A.

1979-01-01

The current irradiation program of helium-bonded uranium--plutonium carbide elements is achieving its original goals. By August 1978, 15 of the original 171 helium-bonded elements had reached their goal burnups including one that had reached the highest burnup of any uranium--plutonium carbide element in the U.S.--12.4 at.%. A total of 66 elements had attained burnups over 8 at.%. Only one cladding breach had been identified at that time. In addition, the systematic and coordinated approach to the current steady-state irradiation tests is yielding much needed information on the behavior of helium-bonded carbide fuel elements that was not available from the screening tests (1965 to 1974). The use of hyperstoichiometric (U,Pu)C containing approx. 10 vol% (U,Pu) 2 C 3 appears to combine lower swelling with only a slightly greater tendency to carburize the cladding than single-phase (U,Pu)C. The selected designs are providing data on the relationship between the experimental parameters of fuel density, fuel-cladding gap size, and cladding type and various fuel-cladding mechanical interaction mechanisms

Repair bond strength of composite resin to sandblasted and laser irradiated Y-TZP ceramic surfaces.

Science.gov (United States)

Kirmali, Omer; Barutcigil, Çağatay; Ozarslan, Mehmet Mustafa; Barutcigil, Kubilay; Harorlı, Osman Tolga

2015-01-01

This study investigated the effects of different surface treatments on the repair bond strength of yttrium-stabilized tetragonal zirconia polycrystalline ceramic (Y-TZP) zirconia to a composite resin. Sixty Y-TZP zirconia specimens were prepared and randomly divided into six groups (n = 10) as follows: Group 1, surface grinding with Cimara grinding bur (control); Group 2, sandblasted with 30 µm silica-coated alumina particles; Group 3, Nd:YAG laser irradiation; Group 4, Er,Cr:YSGG laser irradiation; Group 5, sandblasted + Nd:YAG laser irradiation; and Group 6, sandblasted + Er,Cr:YSGG laser irradiation. After surface treatments, the Cimara(®) System was selected for the repair method and applied to all specimens. A composite resin was built-up on each zirconia surface using a cylindrical mold (5 × 3 mm) and incrementally filled. The repair bond strength was measured with a universal test machine. Data were analyzed using a one-way ANOVA and a Tukey HSD test (p = 0.05). Surface topography after treatments were evaluated by a scanning electron microscope (SEM). Shear bond strength mean values ranged from 15.896 to 18.875 MPa. There was a statistically significant difference between group 3 and the control group (p < 0.05). Also, a significant increase in bond strength values was noted in group 6 (p < 0.05). All surface treatment methods enhanced the repair bond strength of the composite to zirconia; however, there were no significant differences between treatment methods. The results revealed that Nd:YAG laser irradiation along with the combination of sandblasting and Er,Cr:YSGG laser irradiation provided a significant increase in bond strength between the zirconia and composite resin. © Wiley Periodicals, Inc.

Effect of lithium carbonate on leukocyte number after influence of ionizing radiation. 3. Influence of lithium carbonate on peripheral leukocytes after fractionated caudal half-body irradiation

Energy Technology Data Exchange (ETDEWEB)

Rose, H.; Saul, G.; Kehrberg, G. (Humboldt-Universitaet, Berlin (German Democratic Republic). Bereich Medizin (Charite))

1985-01-01

Fractionated half-body irradiation of rats resulted in leukopenia of the peripheral blood. The decrease of leukocytes was smaller in animals pretreated with an orally administered dose of lithium carbonate for 14 days.

Pyroelectric field assisted ion migration induced by ultraviolet laser irradiation and its impact on ferroelectric domain inversion in lithium niobate crystals

International Nuclear Information System (INIS)

Ying, C. Y. J.; Mailis, S.; Daniell, G. J.; Steigerwald, H.; Soergel, E.

2013-01-01

The impact of UV laser irradiation on the distribution of lithium ions in ferroelectric lithium niobate single crystals has been numerically modelled. Strongly absorbed UV radiation at wavelengths of 244–305 nm produces steep temperature gradients which cause lithium ions to migrate and result in a local variation of the lithium concentration. In addition to the diffusion, here the pyroelectric effect is also taken into account which predicts a complex distribution of lithium concentration along the c-axis of the crystal: two separated lithium deficient regions on the surface and in depth. The modelling on the local lithium concentration and the subsequent variation of the coercive field are used to explain experimental results on the domain inversion of such UV treated lithium niobate crystals

Irradiation conditions for fiber laser bonding of HAp-glass ceramics with bovine cortical bone.

Science.gov (United States)

Tadano, Shigeru; Yamada, Satoshi; Kanaoka, Masaru

2014-01-01

Orthopedic implants are widely used to repair bones and to replace articulating joint surfaces. It is important to develop an instantaneous technique for the direct bonding of bone and implant materials. The aim of this study was to develop a technique for the laser bonding of bone with an implant material like ceramics. Ceramic specimens (10 mm diameter and 1 mm thickness) were sintered with hydroxyapatite and MgO-Al2O3-SiO2 glass powders mixed in 40:60 wt% proportions. A small hole was bored at the center of a ceramic specimen. The ceramic specimen was positioned onto a bovine bone specimen and a 5 mm diameter area of the ceramic specimen was irradiated using a fiber laser beam (1070-1080 nm wavelength). As a result, the bone and the ceramic specimens bonded strongly under the irradiation conditions of a 400 W laser power and a 1.0 s exposure time. The maximum shear strength was 5.3 ± 2.3 N. A bonding substance that penetrated deeply into the bone specimen was generated around the hole in the ceramic specimen. On using the fiber laser, the ceramic specimen instantaneously bonded to the bone specimen. Further, the irradiation conditions required for the bonding were investigated.

Effect of Silanization on Microtensile Bond Strength of Different Resin Cements to a Lithium Disilicate Glass Ceramic.

Science.gov (United States)

Gré, Cristina Parise; de Ré Silveira, Renan C; Shibata, Shizuma; Lago, Carlo Tr; Vieira, Luiz Cc

2016-02-01

This study evaluated the influence of a silane-coupling agent on the bond strength of a self-adhesive cement and a conventional resin cement to a lithium disilicate glass ceramic. A total of eight ceramic blocks were fabricated and divided into four groups (n = 2). In groups 1 and 3, ceramic surfaces were etched with hydrofluoric acid 10% for 20 seconds, rinsed for 30 seconds, and air-dried. One layer of a silane agent was applied onto all ceramic specimens and air-dried for 30 seconds. In groups 2 and 4, ceramic surfaces were etched with hydrofluoric acid, rinsed, and air-dried without application of the silane-coupling agent. The ceramic blocks were bonded to a block of composite with a self-adhesive resin cement or with a conventional resin cement, according to the manufacturer's instructions. After 24 hours in distilled water at 37°C, the specimens were sectioned perpendicular to the bonding interface area to obtain beams with a bonding area of 0.8 mm(2) and submitted to a microtensile bond strength test at a crosshead speed of 0.5 mm/min. Data were statistically analyzed with one-way analysis of variance and the Games-Howell post hoc test (p = 0.05). Fractured specimens were examined under optical microscopy at 40x magnification. Silanization resulted in higher microtensile bond strength compared to groups without silane. No significant differences were found between the conventional resin cement and the self-adhesive resin cement with silane agent (p = 0.983), and without silane agent (p = 0.877). Silanization appears to be crucial for resin bonding to a lithium disilicate-based ceramic, regardless of the resin cement used. The self-adhesive resin cement performed as well as the conventional resin cement. Applying one layer of a silane-coupling agent after etching the ceramic surface with hydrofluoric acid 10% enhanced the bond strength between resin cements and a glass ceramic.

Current tritium chemical studies at Oak Ridge National Laboratory

International Nuclear Information System (INIS)

Smith, F.J.; Redman, J.D.; Strehlow, R.A.; Bell, J.T.

1975-01-01

The equilibrium pressures of hydrogen isotopes in the Li-LiH-H 2 , Li-LiD-D 2 and Li-LiT-T 2 systems are being measured. The solubility of hydrogen in lithium was studied and the data are in reasonable agreement with the literature values. The Li-LiD-D 2 system is now being studied. The first experimental measurements of the equilibrium pressures of tritium between 700 and 1000 0 C as a function of the LiT concentration in the Li-LiT-T 2 system have also been completed. The permeation of tritium through clean metals and through metals under simulated steam generator conditions is being investigated. Measurements of tritium permeation through clean nickel at temperatures between 636 and 910 0 K were made using a mixed isotope technique. The tritium permeability, DK/sub s/', as a function of temperature was determined to be ln DK/sub s/' [cc(NTP).mm.min -1 .torr/sup -1/2/.cm -2 ] = -0.906 - 6360/T( 0 K). The measured permeation activation energy was 12.6 +- 0.4 kcal/mole. (MOW)

Standard Practice for Conducting Irradiations at Accelerator-Based Neutron Sources

CERN Document Server

American Society for Testing and Materials. Philadelphia

1996-01-01

1.1 This practice covers procedures for irradiations at accelerator-based neutron sources. The discussion focuses on two types of sources, namely nearly monoenergetic 14-MeV neutrons from the deuterium-tritium T(d,n) interaction, and broad spectrum neutrons from stopping deuterium beams in thick beryllium or lithium targets. However, most of the recommendations also apply to other types of accelerator-based sources, including spallation neutron sources (1). Interest in spallation sources has increased recently due to their proposed use for transmutation of fission reactor waste (2). 1.2 Many of the experiments conducted using such neutron sources are intended to simulate irradiation in another neutron spectrum, for example, that from a DT fusion reaction. The word simulation is used here in a broad sense to imply an approximation of the relevant neutron irradiation environment. The degree of conformity can range from poor to nearly exact. In general, the intent of these simulations is to establish the fundam...

Safety aspects of tritium in ICF reactors with internally-breeding targets

International Nuclear Information System (INIS)

Ragheb, M.; Miley, G.H.; University of Illinois, Urbana, IL)

1985-01-01

The LOTRIT inertial confinement reactor concept employs a deuterium burning target with a DT spark trigger core. This eliminates the need for tritium breeding in a blanket, and leads to a minimization of the tritium inventory and of the possibility of metal fire hazards if lead is used instead of lithium for first wall protection. The active fuel inventory in the fuel cycle and blanket per MJ of energy produced is only 5 percent of the DT case. The most significant reduction in the total tritium inventory is in the target manufacture and storage areas, and is about 1.8% of the DT case per unit of fusion energy produced. If the goal is to reduce the risk from tritium releases from fusion reactors to below that of fission reactors, it is estimated that the tritium releases must be maintained at 0.13-5.0 Ci/day. Attaining these values will be costly, technologically difficult and will constrain the design options in DTbased systems, but may be within the realm of systems using the LOTRIT concept

Comparison of inventory of tritium in various ceramic breeder blankets

International Nuclear Information System (INIS)

Nishikawa, M.; Beloglazov, S.; Nakashima, N.; Hashimoto, K.; Enoeda, M.

2002-01-01

It has been pointed out by the present authors that it is essential to understand such mass transfer steps as diffusion of tritium in the grain of breeder material, absorption of water vapor into bulk of the grain, and adsorption of water on surface of the grain, together with the isotope exchange reaction between hydrogen in purge gas and tritium on surface of breeder material and the isotope exchange reaction between water vapor in purge gas and tritium on surface, for estimation of the tritium inventory in a uniform ceramic breeder blanket under the steady-state condition. It has been also pointed out by the present authors that the water formation reaction on the surface of ceramic breeder materials at introduction of hydrogen can give effect on behavior of bred tritium and lithium transfer in blanket. The tritium inventory for various ceramic breeder blankets are compared in this study basing on adsorption capacity, absorption capacity, isotope exchange capacity, and isotope exchange reactions on the Li 2 O, LiAlO 2 , Li 2 ZrO 3 , Li 4 SiO 4 and Li 2 TiO 3 surface experimentally obtained by the present authors. Effect of each mass transfer steps on the shape of release curve of bred tritium at change of the operational conditions is also discussed from the observation at out pile experiment in KUR. (orig.)

Studies on the recovery of lithium from wash effluent generated during preparation of Li2TiO3 (Lithium Titanate) microspheres for ITER

International Nuclear Information System (INIS)

Bamankar, Y.R.; Vittal Rao, T.V.; Pius, I.C.; Mukerjee, S.K.

2013-01-01

Methods are being developed for the recovery of lithium from wash effluent generated during the preparation of lithium titanate microspheres which are to be used for breeding tritium in ITER Program. Thermal decomposition of the wash effluent in a furnace at 600°C, resulted in decomposition of the impurities such as ammonium chloride, ammonium nitrate, HMTA, and Urea etc., yielding pure lithium salt. Thermal decomposition of wash effluent containing nitrate was carried out in a controlled manner to avoid explosive decomposition of HMTA and ammonium nitrate. Preliminary investigations were also carried out for the separation of lithium as lithium hydroxide from wash effluent using ion exchange membrane coupled with an electrolytic cell. (author)

Development of lithium target system in engineering validation and engineering design activity of the international fusion materials irradiation facility (IFMIF/EVEDA)

International Nuclear Information System (INIS)

Wakai, Eiichi; Kondo, Hiroo; Sugimoto, Masayoshi; Ida, Mizuho; Kanemura, Takuji; Watanabe, Kazuyoshi; Fujishiro, Kouji; Edao, Yuuki; Niitsuma, Shigeto; Kimura, Haruyuki; Fukada, Satoshi; Hiromoto, Tetsushi; Shigeharu, Satoshi; Yagi, Jyuro; Furukawa, Tomohiro; Hirakawa, Yasushi; Suzuki, Akihiro; Terai, Takayuki; Horiike, Hiroshi; Hoashi, Eiji; Suzuki, Sachiko; Yamaoka, Nobuo; Serizawa, Hisashi; Kawahito, Yosuke; Tsuji, Yoshiyuki; Furuya, Kazuyuki; Takeo, Fumio

2012-01-01

Engineering validation and engineering design activity (EVEDA) for the international fusion materials irradiation facility (IFMIF) has been conducted since 2007. Research and development of the Lithium target facility is an important part of this activity. We constructed a world largest liquid Lithium test loop with a capacity of 5000 L in 2010 and successfully completed the first stage validation tests (functional tests of components and Lithium flow test (flow velocity 15 m/s at the target). In the present article, recent results of the EVEDA activity for the Lithium target facility and related technologies on liquid Lithium are reviewed. (author)

Report on the evaluation of the tritium producing burnable absorber rod lead test assembly. Revision 1

International Nuclear Information System (INIS)

1997-03-01

This report describes the design and fabrication requirements for a tritium-producing burnable absorber rod lead test assembly and evaluates the safety issues associated with tritium-producing burnable absorber rod irradiation on the operation of a commercial light water reactor. The report provides an evaluation of the tritium-producing burnable absorber rod design and concludes that irradiation can be performed within U.S. Nuclear Regulatory Commission regulations applicable to a commercial pressurized light water reactor

Toxicity of tritium

International Nuclear Information System (INIS)

Dobson, R.L.

1979-01-01

Among radionuclides of importance in atomic energy, 3 H has relatively low toxicity. The main health and environmental worry is the possibility that significant biological effects may follow from protracted exposure to low concentrations in water. To examine this possible hazard and measure toxicity at low tritium concentrations, chronic exposure studies were done on mice and monkeys. During vulnerable developmental periods animals were exposed to 3 HOH, and mice were exposed also to 60 Co gamma irradiation and energy-related chemical agents. The biological endpoint measured was the irreversible loss of female germ cells. Effects from tritium were observed at surprisingly low concentrations where 3 H was found more damaging than previously thought. Comparisons between tritium and gamma radiation showed the relative biological effectiveness (RBE) to be greater than 1 and to reach approximately 3 at very low exposures. For perspective, other comparisons were made: between radiation and chemical agents, which revealed parallels in action on germ cells, and between pre- and postnatal exposure, which warn of possible special hazard to the fetus from both classes of energy-related byproducts

Compatibility of 316L stainless steel with tritium breeders for fusion reactors

International Nuclear Information System (INIS)

Broc, M.; Fauvet, P.; Flament, T.; Sannier, J.

1986-06-01

Compatibility problems with structural materials are a concern for the choice of the tritium breeder for fusion reactors. In the frame of the European Programme on Fusion Technology, two types of blankets are considered: liquid (eutectic lithium-lead alloy at 0.68 wt % Li: 17Li83Pb) and solid (lithium aluminate or silicate) breeders. This paper is devoted to compatibility studies of 316L stainless steel with 17Li83Pb alloy and γ-LiA10 2 ceramic

Changes of natural killer activity following local 60Co irradiation in intracranial tumor-bearing mice

International Nuclear Information System (INIS)

Otsuka, Shin-ichi; Suda, Kinya; Yamashita, Junkoh; Takeuchi, Juji; Handa, Hajime

1982-01-01

Changes of natural killer activity (NK activity) by local 60 Co irradiation in intracranial tumor-bearing mice were studied by the method of 51 Cr release assay. Local irradiation was administered 10 days after intracranial transplantation of 203-Glioma which had been originally induced by 20-methylcholanthrene in C57BL mice. Irradiation suppressed the growth of tumor and prolonged the mean survival time. The 50% survival time of untreated mice was about 2.5 weeks but that of mice treated by a single dose of 1000 rad and 1500 rad of irradiation was about 4.5 weeks and 6.5 weeks respectively. NK activity of spleen cells in these mice was serially examined. NK activity was gradually increased in mice treated by local irradiation, while it was gradually decreased in mice without treatment. On the other hand, NK activity remained unchanged in non-tumor-bearing control mice. Mice treated with 1000 rad and 1500 rad of irradiation showed 44.0% and 47.6% of % specific 51 Cr release respectively 11 days after irradiation while normal mice showed 18.0%. The increased NK activity after local irradiation suggested that local irradiation might have enhanced the immunological defence mechanisms against the tumor in the tumor-bearing hosts. Some characteristics of effector cells in this assay system were examined. The cytotoxicity of spleen cells was removed by the treatment of anti-BAT serum and complement but was not removed by the treatment of anti-Thy-1.2 serum and complement. Since NK activity reflects the immunological resistance to tumors to some extent, it is felt important to clarify the significance of changes of NK activity in patients with brain tumors in relation to various treatments including surgery, radiotherapy, chemotherapy and immunotherapy in the next step. (author)

Effect of ultraviolet light irradiation period on bond strengths between fiber-reinforced composite post and core build-up composite resin.

Science.gov (United States)

Asakawa, Yuya; Takahashi, Hidekazu; Iwasaki, Naohiko; Kobayashi, Masahiro

2014-01-01

The aim of the present study was to characterize the effects of the ultraviolet light (UV) irradiation period on the bond strength of fiber-reinforced composite (FRC) posts to core build-up resin. Three types of FRC posts were prepared using polymethyl methacrylate, urethane dimethacrylate, and epoxy resin. The surfaces of these posts were treated using UV irradiation at a distance of 15 mm for 0 to 600 s. The pull-out bond strength was measured and analyzed with the Dunnett's comparison test (α=0.05). The bond strengths of the post surfaces without irradiation were 6.9 to 7.4 MPa; those after irradiation were 4.2 to 26.1 MPa. The bond strengths significantly increased after 15 to 120-s irradiation. UV irradiation on the FRC posts improved the bond strengths between the FRC posts and core build-up resin regardless of the type of matrix resin.

Heteroaromatic-based electrolytes for lithium and lithium-ion batteries

Science.gov (United States)

Cheng, Gang; Abraham, Daniel P.

2017-04-18

The present invention provides an electrolyte for lithium and/or lithium-ion batteries comprising a lithium salt in a liquid carrier comprising heteroaromatic compound including a five-membered or six-membered heteroaromatic ring moiety selected from the group consisting of a furan, a pyrazine, a triazine, a pyrrole, and a thiophene, the heteroaromatic ring moiety bearing least one carboxylic ester or carboxylic anhydride substituent bound to at least one carbon atom of the heteroaromatic ring. Preferred heteroaromatic ring moieties include pyridine compounds, pyrazine compounds, pyrrole compounds, furan compounds, and thiophene compounds.

Operating experience with TFTR's Tritium Storage and Delivery System

International Nuclear Information System (INIS)

Voorhees, D.R.

1995-01-01

The Tritium Storage and Delivery System (TSDS) at TFTR was fabricated at Monsanto Mound Lab in the late 1970's and delivered to PPPL in the early 1980's. Commissioning progressed slowly and was finally completed in 1992 following a series of Preoperational tests and Integrated Systems tests. Those tests included thorough leak testing of glove boxes and process piping, electrical interlocks and controls, instrumentation calibrations, volume determinations and verification of uranium bed capacity. The system accepted tritium in dilute form in May of 1993 and began serious usage of pure tritium in November 1993. As the throughput of high purity tritium increased, shortcomings of the system became evident and extensive repairs were implemented. System leakage and material compatibility were the primary causes of the problems. To date, the system has received, stored and delivered over 500 kCi of tritium and is performing very well. The dedicated quadrupole mass spectrometer and beta scintillator system has been analyzing tritium bearing and pure gas streams for over 3 years with minimal downtime

Hysteresis-free high-temperature precise bimorph actuators produced by direct bonding of lithium niobate wafers

Energy Technology Data Exchange (ETDEWEB)

Shur, V. Ya.; Baturin, I. S.; Mingaliev, E. A.; Zorikhin, D. V.; Udalov, A. R.; Greshnyakov, E. D. [Ferroelectric Laboratory, Institute of Natural Sciences, Ural Federal University, 51 Lenin Ave., 620000 Ekaterinburg (Russian Federation)

2015-02-02

The current paper presents a piezoelectric bimorph actuator produced by direct bonding of lithium niobate wafers with the mirrored Y and Z axes. Direct bonding technology allowed to fabricate bidomain plate with precise positioning of ideally flat domain boundary. By optimizing the cutting angle (128° Y-cut), the piezoelectric constant became as large as 27.3 pC/N. Investigation of voltage dependence of bending displacement confirmed that bimorph actuator has excellent linearity and hysteresis-free. Decrease of the applied voltage down to mV range showed the perfect linearity up to the sub-nm deflection amplitude. The frequency and temperature dependences of electromechanical transmission coefficient in wide temperature range (from 300 to 900 K) were investigated.

Tritium biological effects and perspective of the biological study

International Nuclear Information System (INIS)

Komatsu, Kenshi

1998-01-01

Since tritium is an emitter of weak β-rays (5.7keV) and is able to bind to DNA, i.e., the most important genome component, the biological effects should be expected to be more profound than that of X-rays and γ-rays. When carcinogenesis, genetical effects and the detriments for fetus and embryo were used as a biological endpoint, most of tritium RBE (relative biological effectiveness) ranged from 1 to 2. The tritium risk in man could be calculated from these RBEs and γ-ray risk for human exposure, which are obtained mainly from the data on Atomic Bomb survivors. However, the exposure modality from environmental tritium should be a chronic irradiation with ultra low dose rate or a fractionated irradiation. We must estimate the tritium effect in man based on biological experiments alone, due to lack of such epidemiological data. Low dose rate experiment should be always accompanied by the statistical problem of data, since their biological effects are fairy low, and they should involve a possible repair system, such as adaptive response (or hormesis effect) and 'Kada effect' observed in bacteria. Here we discuss future works for the tritium assessment in man, such as (1) developing a high radiation sensitive assay system with rodent hybrid cells containing a single human chromosome and also (2) study on mammal DNA repair at molecular levels using a radiosensitive hereditary disease, Nijmegen Breakage Syndrome. (author)

In-situ ionic conductivity measurement of lithium ceramics under high energy heavy ion irradiation

International Nuclear Information System (INIS)

Nakazawa, Tetsuya; Noda, Kenji; Ishii, Yoshinobu; Ohno, Hideo; Watanabe, Hitoshi; Matsui, Hisayuki.

1992-01-01

To obtain fundamental information regarding the radiation damage in some lithium ceramics, e.g. Li 2 O, Li 4 SiO 4 etc., candidate of breeder materials exposed to severe irradiation environment, an in-situ experiment technique for the ionic conductivity measurement, which allows the specimen temperature control and the beam current monitoring, have been developed. This paper describes the features of an apparatus to measure in situ the ionic conductivity under the irradiation environment and presents some results of ionic conductivity measured for typical ceramic breeders using this apparatus. (J.P.N.)

Calculations of tritium breeding ratio and inventory distributions of FEB blanket

International Nuclear Information System (INIS)

Deng Baiquan

2001-01-01

Based on the design features of FEB reactor blanket, the tritium breeding ratio and tritium concentrations in liquid lithium of each breeding zone have been calculated after 10 days full power operation for outboard blanket and one day operation for inboard blanket. The comparisons with the results calculated by Monte-Carlo code MORSE-CGT are made. Meanwhile the inventory in beryllium multiplier after one-year full power operation has also been estimated. An important conclusion has been drew the thermal hydraulic design should be careful to guarantee the blanket temperature should not rise as high as 680 degree C

Liquid lithium loop system to solve challenging technology issues for fusion power plant

Science.gov (United States)

Ono, M.; Majeski, R.; Jaworski, M. A.; Hirooka, Y.; Kaita, R.; Gray, T. K.; Maingi, R.; Skinner, C. H.; Christenson, M.; Ruzic, D. N.

2017-11-01

Steady-state fusion power plant designs present major divertor technology challenges, including high divertor heat flux both in steady-state and during transients. In addition to these concerns, there are the unresolved technology issues of long term dust accumulation and associated tritium inventory and safety issues. It has been suggested that radiation-based liquid lithium (LL) divertor concepts with a modest lithium-loop could provide a possible solution for these outstanding fusion reactor technology issues, while potentially improving reactor plasma performance. The application of lithium (Li) in NSTX resulted in improved H-mode confinement, H-mode power threshold reduction, and reduction in the divertor peak heat flux while maintaining essentially Li-free core plasma operation even during H-modes. These promising results in NSTX and related modeling calculations motivated the radiative liquid lithium divertor concept and its variant, the active liquid lithium divertor concept, taking advantage of the enhanced or non-coronal Li radiation in relatively poorly confined divertor plasmas. To maintain the LL purity in a 1 GW-electric class fusion power plant, a closed LL loop system with a modest circulating capacity of ~1 l s-1 is envisioned. We examined two key technology issues: (1) dust or solid particle removal and (2) real time recovery of tritium from LL while keeping the tritium inventory level to an acceptable level. By running the LL-loop continuously, it can carry the dust particles and impurities generated in the vacuum vessel to the outside where the dust/impurities can be removed by relatively simple dust filter, cold trap and/or centrifugal separation systems. With ~1 l s-1 LL flow, even a small 0.1% dust content by weight (or 0.5 g s-1) suggests that the LL-loop could carry away nearly 16 tons of dust per year. In a 1 GW-electric (or ~3 GW fusion power) fusion power plant, about 0.5 g s-1 of tritium is needed to maintain the fusion fuel cycle

Protons in neutron-irradiated and thermochemically reduced MgO crystals doped with lithium impurities

International Nuclear Information System (INIS)

Gonzalez, R.; Pareja, R.; Chen, Y.

1992-01-01

H - (hydride) ions have been observed in lithium-doped MgO crystals which have been neutron irradiated or thermochemically reduced (TCR). Infrared-absorption measurements have been used to identify the local modes of the H - ions in these crystals. The concentration of the H - ions in the neutron-irradiated crystals is found to be far less than that found in the TCR crystals. The thermal stability of H - and oxygen vacancies in both oxidizing and reducing atmospheres are investigated. The emergence of sharp structures due to OH - ions is attributed to the displacements of substitutional Li + ions, leaving behind unperturbed OH - ions, via a mechanism of rapid radiation-induced diffusion during irradiation in a reactor. Results of neutron-irradiated MgO:Li, which had previously been oxidized at high temperature, are also presented

Materials considerations in accelerator targets

International Nuclear Information System (INIS)

Peacock, H.B. Jr.; Iyer, N.C.; Louthan, M.R. Jr.

1994-01-01

Future nuclear materials production and/or the burn-up of long lived radioisotopes may be accomplished through the capture of spallation produced neutrons in accelerators. Aluminum clad-lead and/or lead alloys has been proposed as a spallation target. Aluminum was the cladding choice because of the low neutron absorption cross section, fast radioactivity decay, high thermal conductivity, and excellent fabricability. Metallic lead and lead oxide powders were considered for the target core with the fabrication options being casting or powder metallurgy (PM). Scoping tests to evaluate gravity casting, squeeze casting, and casting and swaging processes showed that, based on fabricability and heat transfer considerations, squeeze casting was the preferred option for manufacture of targets with initial core cladding contact. Thousands of aluminum clad aluminum-lithium alloy core targets and control rods for tritium production have been fabricated by coextrusion processes and successfully irradiated in the SRS reactors. Tritium retention in, and release from the coextruded product was modeled from experimental and operational data. Newly produced tritium atoms were trapped by lithium atoms to form a lithium tritide. The effective tritium pressure required for trap or tritide stability was the equilibrium decomposition pressure of tritium over a lithium tritide-aluminum mixture. The temperature dependence of tritium release was determined by the permeability of the cladding to tritium and the local equilibrium at the trap sites. The model can be used to calculate tritium release from aluminum clad, aluminum-lithium alloy targets during postulated accelerator operational and accident conditions. This paper describes the manufacturing technologies evaluated and presents the model for tritium retention in aluminum clad, aluminum-lithium alloy tritium production targets

Development of tritium permeation barriers on Al base in Europe

Science.gov (United States)

Benamati, G.; Chabrol, C.; Perujo, A.; Rigal, E.; Glasbrenner, H.

The development of the water cooled lithium lead (WCLL) DEMO fusion reactor requires the production of a material capable of acting as a tritium permeation barrier (TPB). In the DEMO blanket reactor permeation barriers on the structural material are required to reduce the tritium permeation from the Pb-17Li or the plasma into the cooling water to acceptable levels (HIP) technology and spray (this one developed also for repair) deposition techniques. The final goal is to select a reference technique to be used in the blanket of the DEMO reactor and in the ITER test module fabrication. The activities performed in four European laboratories are summarised here.

Effect of LASER Irradiation on the Shear Bond Strength of Zirconia Ceramic Surface to Dentin

Directory of Open Access Journals (Sweden)

Sima Shahabi

2012-09-01

Full Text Available Background and Aims: Reliable bonding between tooth substrate and zirconia-based ceramic restorations is always of great importance. The laser might be useful for treatment of ceramic surfaces. The aim of the present study was to investigate the effect of laser irradiation on the shear bond strength of zirconia ceramic surface to dentin. Materials and Methods: In this experimental in vitro study, 40 Cercon zirconia ceramic blocks were fabricated. The surface treatment was performed using sandblasting with 50-micrometer Al2O3, CO2 laser, or Nd:YAG laser in each test groups. After that, the specimens were cemented to human dentin with resin cement. The shear bond strength of ceramics to dentin was determined and failure mode of each specimen was analyzed by stereo-microscope and SEM investigations. The data were statistically analyzed by one-way analysis of variance and Tukey multiple comparisons. The surface morphology of one specimen from each group was investigated under SEM. Results: The mean shear bond strength of zirconia ceramic to dentin was 7.79±3.03, 9.85±4.69, 14.92±4.48 MPa for CO2 irradiated, Nd:YAG irradiated, and sandblasted specimens, respectively. Significant differences were noted between CO2 (P=0.001 and Nd:YAG laser (P=0.017 irradiated specimens with sandblasted specimens. No significant differences were observed between two laser methods (P=0.47. The mode of bond failure was predominantly adhesive in test groups (CO2 irradiated specimens: 75%, Nd:YAG irradiated: 66.7%, and sandblasting: 41.7%. Conclusion: Under the limitations of the present study, surface treatment of zirconia ceramics using CO2 and Nd:YAG lasers was not able to produce adequate bond strength with dentin surfaces in comparison to sandblasting technique. Therefore, the use of lasers with the mentioned parameters may not be recommended for the surface treatment of Cercon ceramics.

Tritium conference days; Journees tritium

Energy Technology Data Exchange (ETDEWEB)

Garnier-Laplace, J.; Lebaron-Jacobs, L.; Sene, M.; Devin, P.; Chretien, V.; Le Guen, B.; Guetat, Ph.; Baglan, N.; Ansoborlo, E.; Boyer, C.; Masson, M.; Bailly-Du-Bois, P.; Jenkinson, St.; Wakeford, R.; Saintigny, Y.; Romeo, P.H.; Thompson, P.; Leterq, D.; Chastagner, F.; Cortes, P.; Philippe, M.; Paquet, F.; Fournier, M.

2009-07-01

This document gathers the slides of the available presentations given during this conference day. Twenty presentations out of 21 are assembled in the document and deal with: 1 - tritium in the environment (J. Garnier-Laplace); 2 - status of knowledge about tritium impact on health (L. Lebaron-Jacobs); 3 - tritium, discrete but present everywhere (M. Sene); 4 - management of tritium effluents from Areva NC La Hague site - related impact and monitoring (P. Devin); 5 - tritium effluents and impact in the vicinity of EDF's power plants (V. Chretien and B. Le Guen); 6 - contribution of CEA-Valduc centre monitoring to the knowledge of atmospheric tritiated water transfers to the different compartments of the environment (P. Guetat); 7 - tritium analysis in environment samples: constraints and means (N. Baglan); 8 - organically-linked tritium: the analyst view (E. Ansoborlo); 9 - study of tritium transfers to plants via OBT/HTO{sub air} and OBT/HTO{sub free} (C. Boyer); 10 - tritium in the British Channel (M. Masson and P. Bailly-Du-Bois); 11 - tritium in British coastal waters (S. Jenkinson); 12 - recent results from epidemiology (R. Wakeford); 13 - effects of tritiated thymidine on hematopoietic stem cells (P.H. Romeo); 14 - tritium management issue in Canada: the point of view from authorities (P. Thompson); 15 - experience feedback of the detritiation process of Valduc centre (D. Leterq); 16 - difficulties linked with tritiated wastes confinement (F. Chastagner); 17 - optimisation of tritium management in the ITER project (P. Cortes); 18 - elements of thought about the management of tritium generated by nuclear facilities (M. Philippe); 19 - CIPR's position about the calculation of doses and risks linked with tritium exposure (F. Paquet); 20 - tritium think tanks (M. Fournier). (J.S.)

Tritium breeding measurements in a lithium blanket module with Pb/Be multipliers at the LOTUS facility

International Nuclear Information System (INIS)

Azam, S.; Kumar, A.

1987-01-01

The lithium blanket module (LBM) was lent for a fixed duration in 1985 to Ecole Polytechnique Federale de Lausanne under an agreement with the Electric Power Research Institute and Princeton Plasma Physics Laboratory. The first tritium breeding measurements in the central rod of the LBM and their analysis have been reported previously. Some time ago, we carried out additional experiments wherein the Li 2 O sample disk, each having a theoretical density of ∼85% and dimensions of 17.8-mm diam x 0.9-mm thickness, were placed in four removable rods. In addition to the central rod, the other rods were at ∼6-, 18-, and 39-cm radial distances from the axis of the central one. The sample disks wee kept at every 3 cm inside each of these rods up to a length of 30 cm in the Li 2 O part of the LBM. The choice of the off-axis rods resulted from our interest in investigating the effect of room return on tritium breeding in the LBM. We chose two of the leading neutron multipliers: (a) a 5-cm-thick (∼100- x 110-cm) lead slab and (b) a 6-cm-thick (∼66- x 66-cm) beryllium slab. The experimental assembly, consisting of the multiplier followed by the LBM, was kept at 10 cm from the generator. A packet of three foils, zirconium, indium, and aluminum, was placed at the center of the flat face of the generator to monitor the source intensity during the 10-h operation for the experiments with each multiplier. The source intensity is deduced to be ∼1.9 x 10 12 n/s for both the experiments. 5 refs., 3 figs

Review of JAEA activities on the IFMIF liquid lithium target in FY2006

International Nuclear Information System (INIS)

Ida, Mizuho; Nakamura, Hiroo; Miyashita, Makoto; Sugimoto, Masayoshi; Chida, Teruo; Furuya, Kazuyuki; Yoshida, Eiichi; Hirakawa, Yasuhi; Miyake, Osamu; Hirabayashi, Masaru; Ara, Kuniaki

2008-03-01

Engineering Validation Design and Engineering Design Activity (EVEDA) of the International Fusion Materials Irradiation Facility (IFMIF) is under going. IFMIF is an accelerator-based Deuterium-Lithium (D-Li) neutron source to produce intense high energy neutrons and a sufficient irradiation volume for testing candidate materials for fusion reactors. To realize such a condition, 40 MeV deuteron beam with a current of 250 mA is injected into high speed liquid Li flow with a speed of 20 m/s. In target system, nuclear heating due to neutron causes thermal stress especially on a back-wall of the target assembly. In addition, radioactive species such as beryllium-7, tritium and activated corrosion products are generated. In this report, thermal stress analyses of the back-wall, mechanical tests on weld specimen made of the back-wall material, estimations of beryllium-7 behavior and worker dose at the IFMIF Li loop and consideration on major EVEDA tasks are summarized. (author)

Microstructural stability of a self-ion irradiated lanthana-bearing nanostructured ferritic steel

International Nuclear Information System (INIS)

Pasebani, Somayeh; Charit, Indrajit; Burns, Jatuporn; Price, Lloyd M.; M Univ., College Station, TX; Shao, Lin; M Univ., College Station, TX

2015-01-01

Thermally stable nanofeatures with high number density are expected to impart excellent high temperature strength and irradiation stability in nanostructured ferritic steels (NFSs) which have potential applications in advanced nuclear reactors. A lanthana-bearing NFS (14LMT) developed via mechanical alloying and spark plasma sintering was used in this study. The sintered samples were irradiated by Fe 2+ ions to 10, 50 and 100 dpa at 30 °C and 500 °C. Microstructural and mechanical characteristics of the irradiated samples were studied using different microscopy techniques and nanoindentation, respectively. Overall morphology and number density of the nanofeatures remained unchanged after irradiation. Average radius of nanofeatures in the irradiated sample (100 dpa at 500 °C) was slightly reduced. A notable level of irradiation hardening and enhanced dislocation activity occurred after ion irradiation except at 30 °C and ≥50 dpa. Other microstructural features like grain boundaries and high density of dislocations also provided defect sinks to assist in defect removal.

Modeling tritium behavior in Li{sub 2}ZrO{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Billone, M C [Argonne National Lab., IL (United States). Fusion Power Program

1998-03-01

Lithium metazirconate (Li{sub 2}ZrO{sub 3}) is a promising tritium breeder material for fusion reactors because of its excellent tritium release characteristics. In particular, for water-cooled breeding blankets (e.g., ITER), Li{sub 2}ZrO{sub 3} is appealing from a design perspective because of its good tritium release at low operating temperatures. The steady-state and transient tritium release/retention database for Li{sub 2}ZrO{sub 3} is reviewed, along with conventional diffusion and first-order surface desorption models which have been used to match the database. A first-order surface desorption model is recommended in the current work both for best-estimate and conservative (i.e., inventory upper-bound) predictions. Model parameters are determined and validated for both types of predictions, although emphasis is placed on conservative design predictions. The effects on tritium retention of ceramic microstructure, protium partial pressure in the purge gas and purge gas flow rate are discussed, along with other mechanisms for tritium retention which may not be dominant in the experiments, but may be important in blanket design analyses. The proposed tritium retention/release model can be incorporated into a transient thermal performance code to enable whole-blanket predictions of tritium retention/release during cyclic reactor operation. Parameters for the ITER driver breeding blanket are used to generate a numerical set of model predictions for steady-state operation. (author)

Reduction of multiple carbon-carbon bonds by gaseous tritium as a method for production of preparations with high molar radioactivity

International Nuclear Information System (INIS)

Shevchenko, V.P.; Potapova, A.V.; Myasoedov, N.F.

1989-01-01

A study was made on the effect of temperature, pressure of gas mixture, degree of catalyst saturation with hydrogen, nature of solvent, catalyst and nonsaturated compound on the yield and molar radioactivity of tritium labelled preparations. It is shown that variation of conditions of the hydrogenation reaction of edge double bond enables to increase sufficiently the total molar radioactivity of such compounds in result of reaction of isotope exchange. The developed method enables to prepare multiple-labelled biologically active compounds (0.45-3.33 PBq/mol) with high chemical yield (70-99 %)

Ratio of tritiated water and hydrogen generated in mercury through a nuclear reaction

Energy Technology Data Exchange (ETDEWEB)

Manabe, K. [Nuclear Science and Engineering Directorate, Japan Atomic Energy Agency (JAEA), Tokai, Naka-gun, Ibaraki 319-1195 (Japan)], E-mail: manabe.kentaro@jaea.go.jp; Yokoyama, S. [Nuclear Science and Engineering Directorate, Japan Atomic Energy Agency (JAEA), Tokai, Naka-gun, Ibaraki 319-1195 (Japan)

2008-02-15

Tritium generated in a mercury target is a source of potential exposure of personnel at high-energy accelerator facilities. Knowledge of the chemical form of tritium is necessary to estimate the internal doses. We studied the tritium generation upon thermal neutron irradiation of a mercury target modified into liquid lithium amalgam to examine the ratio of tritiated water ([{sup 3}H]H{sub 2}O) and tritiated hydrogen ([{sup 3}H]H{sub 2}). The ratio between [{sup 3}H]H{sub 2}O and [{sup 3}H]H{sub 2} generated in lithium amalgam was 4:6 under these experimental conditions.

Cellular- and micro-dosimetry of heterogeneously distributed tritium.

Science.gov (United States)

Chao, Tsi-Chian; Wang, Chun-Ching; Li, Junli; Li, Chunyan; Tung, Chuan-Jong

2012-01-01

The assessment of radiotoxicity for heterogeneously distributed tritium should be based on the subcellular dose and relative biological effectiveness (RBE) for cell nucleus. In the present work, geometry-dependent absorbed dose and RBE were calculated using Monte Carlo codes for tritium in the cell, cell surface, cytoplasm, or cell nucleus. Penelope (PENetration and Energy LOss of Positrins and Electrons) code was used to calculate the geometry-dependent absorbed dose, lineal energy, and electron fluence spectrum. RBE for the intestinal crypt regeneration was calculated using a lineal energy-dependent biological weighting function. RBE for the induction of DNA double strand breaks was estimated using a nucleotide-level map for clustered DNA lesions of the Monte Carlo damage simulation (MCDS) code. For a typical cell of 10 μm radius and 5 μm nuclear radius, tritium in the cell nucleus resulted in much higher RBE-weighted absorbed dose than tritium distributed uniformly. Conversely, tritium distributed on the cell surface led to trivial RBE-weighted absorbed dose due to irradiation geometry and great attenuation of beta particles in the cytoplasm. For tritium uniformly distributed in the cell, the RBE-weighted absorbed dose was larger compared to tritium uniformly distributed in the tissue. Cellular- and micro-dosimetry models were developed for the assessment of heterogeneously distributed tritium.

Startup of Experimental Lithium System

International Nuclear Information System (INIS)

McCauley, D.L.

1980-06-01

The Experimental Lithium System (ELS) is designed for full-scale testing of targets and other lithium system components for the Fusion Materials Irradiation Test (FMIT) Facility. The system also serves as a test bed for development of lithium purification and characterization equipment, provides experience in operation of large lithium systems, and helps guide FMIT design

Material modifications in lithium niobate and lithium tantalate crystals by ion irradiation; Materialmodifikationen in Lithiumniobat- und Lithiumtantalat-Kristallen durch Ionenbestrahlung

Energy Technology Data Exchange (ETDEWEB)

Raeth, Niels Lennart

2017-02-17

The artificially produced crystals lithium niobate (LiNbO{sub 3}) and the closely related lithium tantalate (LiTaO{sub 3}) are proven starting materials for producing active and passive devices that can guide, amplify, switch and process light. For this purpose, it is often necessary to be able to influence the refractive index of the substrate targeted, which is possible in addition to other methods by irradiation of the materials with fast light ions. In this work, lithium niobate and lithium tantalate crystals are irradiated with alpha particles, {sup 3}He ions, deuterons, and protons at projectile energies of up to 14 MeV / nucleon. Energy and crystal thickness are chosen so that the projectiles penetrate the entire sample and are not implanted. All isotopes responsible for the unwanted nuclear activation of the crystals due to the irradiation are relatively short-lived and overall the activation decreases fast enough to allow the safe handling of the irradiated samples after a storage period of a few days to a few weeks. The refractive index changes produced in lithium niobate and lithium tantalate by irradiation with the different projectiles are determined interferometrically and can also be measured by suitable choice of the sample geometry as a function of the ion penetration depth: In LiNbO{sub 3} the ordinary refractive index decreases, the extraordinary increases equally. In LiTaO{sub 3}, both the ordinary and the extraordinary refractive indices decrease as a result of the irradiation; the ordinary refractive index change is many times stronger than the extraordinary one. There is an enormous long-term stability at room temperature for both crystal systems: Even after eleven (LiNbO{sub 3}) or three (LiTaO{sub 3}) years, no decrease in the ion beam-induced refractive index change can be observed. The ion beam-induced refractive index changes are probably the result of atomic displacements such as vacancies, defect clusters or ''latent tracks

Evaluation of bond strength of a conventional adhesive system in irradiated teeth

Directory of Open Access Journals (Sweden)

Emanuel Jordan de CARVALHO

Full Text Available Abstract Introduction One of the most common treatments of head and neck cancer patients is radiotherapy, a treatment method which uses ionizing radiation beam and destroys tumor cells, minimizing damage to neighbor cells. Purpose To evaluate the bond strength of a conventional adhesive system in irradiated teeth. Method 24 third human molars, 12 of which were randomly exposed to radiation and prepared from the removal of occlusal enamel, then exposed to a flat dentine surface. The adhesive system Stae was applied according to the manufacturer’s instructions. Next, two 2 mm increments of resin were implemented. The samples were hemi sectioned specimens, originating shapped toothpick. To evaluate the bond strength, a micro tensile test was done with 500N load and speed of 0.5 mm/minute. Result There was no statistically significant difference between the bond strength of teeth which were or were not exposed to radiation and which used a conventional adhesive system. Conclusion Although the radiation doses applied may cause some alterations in microscopic range in dental tissues, it can be concluded that these alterations do not influence in the bond strength in dentin of irradiated teeth.

Investigation of non-magnetic alloys for the suppression of tritium permeation

International Nuclear Information System (INIS)

1980-07-01

The present work was aimed at identification of alloys which might combine low tritium permeation with other properties desired in fusion reactor vessels, heat exchangers, lithium-handling plumbing and other components likely to contain tritium. These properties include low radiation damage, low magnetic permeability, high temperature strength, and compatibility with potential heat transfer and blanket materials. The work consisted of two tasks: problem definition, and literature search and analysis. Task I was complicated by the incomplete status of fusion reactor development, particularly with respect to selection of coolant and blanket materials and temperatures. The approach taken was to establish a probable range of requirements

Bonding performance of universal adhesives to er,cr:YSGG laser-irradiated enamel.

Science.gov (United States)

Ayar, Muhammet Kerim; Erdemir, Fatih

2017-04-01

Universal adhesives have been recently introduced for use as self-etch or etch-and-rinse adhesives depending on the dental substrate and clinical condition. However, their bonding effectiveness to laser-irradiated enamel is still not well-known. Thus, the aim of this study was to compare the shear bond strength (SBS) of universal adhesives (Single Bond Universal; Nova Compo-B Plus) applied to Er,Cr:YSGG laser-irradiated enamel with SBS of the same adhesives applied in self-etch and acid-etching modes, respectively. Crown segments of sixty bovine incisors were embedded into standardized acrylic blocks. Flattened enamel surfaces were prepared. Specimens were divided into six groups according to universal adhesives and application modes randomly (n = 10), as follows: Single Bond Universal/acid-etching mode; Nova Compo-B Plus/acid-etching mode; Single Bond Universal/self-etching mode; Nova Compo-B Plus/self-etching mode; and Single Bond Universal/Er,Cr:YSGG Laser-etching mode; Nova Compo-B Plus/Er,Cr:YSGG Laser-etching mode. After surface treatments, universal adhesives were applied onto surfaces. SBS was determined after storage in water for 24 h using a universal testing machine with a crosshead speed of 0.5 mm min -1 . Failure modes were evaluated using a stereomicroscope. Data was analyzed using two-way of analyses of variances (ANOVA) (p = 0.05). Two-way ANOVA revealed that adhesive had no effect on SBS (p = 0.88), but application mode significantly influenced SBS (p = 0.00). Acid-etching significantly increased SBS, whereas there are no significant differences between self-etch mode and laser-etching for both adhesives. The bond strength of universal adhesives may depend on application mode. Acid etching may significantly increase bond strength, while laser etching may provide similar bond strength when compared to self-etch mode. © 2016 Wiley Periodicals, Inc.

Consistency of neutron cross-section data, S /SUB N/ calculations, and measured tritium production for a 14-MeV neutron-driven sphere of natural lithium deuteride

International Nuclear Information System (INIS)

Reupke, W.A.; Davidson, J.N.; Muir, D.W.

1982-01-01

The authors present algorithms, describe a computer program, and gives a computational procedure for the statistical consistency analysis of neutron cross-section data, S /SUB N/ calculations, and measured tritium production in 14-MeV neutron-driven integral assemblies. Algorithms presented include a reduced matrix manipulation technique suitable for manygroup, 14-MeV neutron transport calculations. The computer program incorporates these algorithms and is expanded and improved to facilitate analysis of such integral experiments. Details of the computational procedure are given for a natural lithium deuteride experiment performed at the Los Alamos National Laboratory. Results are explained in terms of calculated cross-section sensitivities and uncertainty estimates. They include a downward adjustment of the 7 Li(n,xt) 14-MeV cross section from 328 + or - 22 to 284 + or - 24 mb, which is supported by the trend of recent differential and integral measurements. It is concluded that with appropriate refinements, the techniques of consistency analysis can be usefully applied to the analysis of 14-MeV neutron-driven tritium production integral experiments

Direct measurement of tritium production rate in LiPb with removed parasitic activities: Preliminary experiments

Energy Technology Data Exchange (ETDEWEB)

Kuc, Tadeusz, E-mail: kuc@agh.edu.pl; Pohorecki, Władysław; Ostachowicz, Beata

2014-10-15

Liquid scintillation (LS) technique applied to direct measurement of tritium activity produced in LiPb eutectic in Frascati HCLL TBM mock-up neutronic experiment has been tested so far in the case of LS measurement after long period since irradiation. LiPb samples irradiated in neutron filed show, except of tritium, meaningful activity of other radioisotopes (parasitic). Parasitic activity, mainly from isotopes of lead ({sup 209}Pb, {sup 204m}Pb, {sup 203}Pb) calculated with the use of FISPACT, exceeds ca 5 times tritium activity 1.4 h after irradiation. We propose to remove disturbing radioisotopes in a chemical way to avoid long “cooling” of the irradiated samples before tritium measurement. Samples (1 g of LiPb) irradiated in reactor fast neutron flux were diluted and metallic cations removed by chemical precipitation. For this purpose we used: potassium iodide (KJ), strontium chloride (SrCl{sub 2}), APDC (C{sub 5}H{sub 8}NS{sub 2}·NH{sub 4}), NaDDTC (C{sub 5}H{sub 10}NNaS{sub 2}·3H{sub 2}O), and PAN (C{sub 15}H{sub 11}N{sub 3}O). Precipitation procedure in each case lasted ca 5–25 min, and the following filtration next 10–20 min. In each filtrate (ca 120 ml) we measured Pb concentration in total reflection X-ray fluorescence (TXRF) analyzer and parasitic activity (left after 21-day “cooling”) applying HPGe gamma spectrometer. Pb cations precipitated by SrCl{sub 2} and than by PAN lowered activity of Pb isotopes to less than 1% of the initial tritium activity. Another combination of reagents: NaDDTC followed by SrCl{sub 2} in a single and double step filtration reduced Pb concentration 10{sup 2} and 10{sup 4} times, respectively. Reduction of this order allows tritium radiometric measurement ca 3 h after irradiation with acceptable accuracy. This time can be shortened by applying correction for decay of known parasitic activity. Input of {sup 76}As and other less abundant radioisotopes can be eliminated using high purity LiPb. Tritium activity of

Lithium protects hippocampal progenitors, cognitive performance and hypothalamus-pituitary function after irradiation to the juvenile rat brain

NARCIS (Netherlands)

Zhou, Kai; Xie, Cuicui; Wickström, Malin; Dolga, Amalia M; Zhang, Yaodong; Li, Tao; Xu, Yiran; Culmsee, Carsten; Kogner, Per; Zhu, Changlian; Blomgren, Klas

2017-01-01

Cranial radiotherapy in children typically causes delayed and progressive cognitive dysfunction and there is no effective preventive strategy for radiation-induced cognitive impairments. Here we show that lithium treatment reduced irradiation-induced progenitor cell death in the subgranular zone of

Modeling the Removal of Xenon from Lithium Hydrate with Aspen HYSYS

Science.gov (United States)

Efthimion, Phillip; Gentile, Charles

2011-10-01

The Laser Inertial Fusion Engine (LIFE) project mission is to provide a long-term, carbon-free source of sustainable energy, in the form of electricity. A conceptual xenon removal system has been modeled with the aid of Aspen HYSYS, a chemical process simulator. Aspen HYSYS provides excellent capability to model chemical flow processes, which generates outputs which includes specific variables such as temperature, pressure, and molar flow. The system is designed to strip out hydrogen isotopes deuterium and tritium. The base design bubbles plasma exhaust laden with x filled with liquid helium. The system separates the xenon from the hydrogen, deuterium, and tritium with a lithium hydrate and a lithium bubbler. After the removal of the hydrogen and its isotopes, the xenon is then purified by way of the process of cryogenic distillation. The pure hydrogen, deuterium, and tritium are then sent to the isotope separation system (ISS). The removal of xenon is an integral part of the laser inertial fusion engine and Aspen HYSYS is an excellent tool to calculate how to create pure xenon.

Irradiation effects and hydrogen behavior in H{sub 2}{sup +} and He{sup +} implanted γ-LiAlO{sub 2} single crystals

Energy Technology Data Exchange (ETDEWEB)

Jiang, Weilin, E-mail: weilin.jiang@pnnl.gov [Pacific Northwest National Laboratory, Richland, WA (United States); Zhang, Jiandong; Kovarik, Libor; Zhu, Zihua [Pacific Northwest National Laboratory, Richland, WA (United States); Price, Lloyd; Gigax, Jonathan; Castanon, Elizabeth; Wang, Xuemei; Shao, Lin [Department of Nuclear Engineering, Texas A& M University, College Station, TX (United States); Senor, David J. [Pacific Northwest National Laboratory, Richland, WA (United States)

2017-02-15

Gamma-phase lithium aluminate (γ-LiAlO{sub 2}) is a breeder material for tritium, a necessary substance for strategic stockpile and fusion power systems. A fundamental study of structural evolution and tritium diffusion in γ-LiAlO{sub 2} under displacive irradiation is needed to fully assess the material performance. This study utilizes ion implantation of protium (surrogate for tritium) and helium in γ-LiAlO{sub 2} single crystals at elevated temperatures to emulate the irradiation effects. The results show that at 573 K there are two distinct disorder saturation stages to 1 dpa without full amorphization; overlapping implantation of H{sub 2}{sup +} and He{sup +} ions suggests possible formation of gas bubbles. For irradiation to 10{sup 21} H{sup +}/m{sup 2} (0.36 dpa at peak) at 773 K, amorphization occurs at surface with H diffusion and dramatic Li loss; the microstructure contains bubbles and cubic LiAl{sub 5}O{sub 8} precipitates with sizes up to 200 nm or larger. In addition, significant H diffusion and release are observed during thermal annealing. - Highlights: • Disorder saturation stages are observed in γ-LiAlO{sub 2} irradiated with H{sub 2}{sup +} ions at 573 K. • Li loss occurs during H{sub 2}{sup +} ion implantation in γ-LiAlO{sub 2} at elevated temperatures (573–773 K). • Both gas bubbles and cubic LiAl{sub 5}O{sub 8} precipitates are formed in γ-LiAlO{sub 2} irradiated with H{sub 2}{sup +} ions at 773 K. • Isochronal annealing at temperatures up to 773 K leads to significant H release.

Tritium target manufacturing for use in accelerators

Science.gov (United States)

Bach, P.; Monnin, C.; Van Rompay, M.; Ballanger, A.

2001-07-01

As a neutron tube manufacturer, SODERN is now in charge of manufacturing tritium targets for accelerators, in cooperation with CEA/DAM/DTMN in Valduc. Specific deuterium and tritium targets are manufactured on request, according to the requirements of the users, starting from titanium target on copper substrate, and going to more sophisticated devices. A wide range of possible uses is covered, including thin targets for neutron calibration, thick targets with controlled loading of deuterium and tritium, rotating targets for higher lifetimes, or large size rotating targets for accelerators used in boron neutron therapy. Activity of targets lies in the 1 to 1000 Curie, diameter of targets being up to 30 cm. Special targets are also considered, including surface layer targets for lowering tritium desorption under irradiation, or those made from different kinds of occluders such as titanium, zirconium, erbium, scandium, with different substrates. It is then possible to optimize either neutron output, or lifetime and stability, or thermal behavior.

Methods of removal of tritium from aqueous effluent: a review of international research and development

International Nuclear Information System (INIS)

Segal, M.G.

1988-01-01

Tritium is formed in thermal nuclear reactors both by neutron activation of elements such as deuterium and lithium and by ternary fission in the fuel. It is a weak beta-emitter with a short half-life, 12.3 years, and its radiological significance in reactor discharges is very low. In heavy-water-cooled and -moderated reactors, such as the CANDU stations, the tritium concentration in the moderator is sufficiently high to cause a potential hazard to operators, and so a major research and development programme has been carried out on processes to remove the tritium. Detritiation of light water has also been the subject of major R and D effort world-wide, because reprocessing operations can generate significant quantities of tritium in liquid waste, and high concentrations of tritium may arise in some aqueous streams in fusion reactors. This Report presents a review of the methods that have been proposed, studied and developed for removal of tritium from light and heavy water: the principles of individual methods are discussed, and the current status of their development is reviewed. (author)

A critical analysis of the impact assessment of environmental tritium

International Nuclear Information System (INIS)

Jain, Narendra; Bhatia, Arvind

2013-01-01

Tritium, a radionuclide of hydrogen has longer life and gets more rapidly dispersed, but before becoming globally distributed, it represents a significant radiobiological risk to the local population exposed. It is produced naturally in the upper atmosphere by the interaction of cosmic rays with nitrogen and hydrogen. The tritons in the upper atmosphere are oxidized to tritiated water (HTO) and mix with the hydrosphere generally through the movement of air masses and precipitation. Terrestrially, tritium may be formed by the action of lithium on neutrons. There is apprehension that the recent controversy concerning the health and environmental impact of tritium may end up as worldwide contaminants in the final analysis. From many varied reports from different laboratories, it appears that projected levels for fusion reactors may also produce deleterious and detectable effects. The degree of concern over tritium problem is evidenced by a rapid increase in publications on the health implications of environmental tritium. The present issues of controversy will be intensified as the fusion reactor technology approaches the door step of public and the possible health detriment from its radioactive emissions arouse concern. The current project has been planned keeping some such points in view. It reviews the work on the behavior of tritium in its various forms in the environment with an emphasis on the release from various sources, its world inventories at present level sand its transfer into the various compartments of ecosystems. Besides this, its metabolism in biosystem and the possible implications of low doses of tritium in present and future generations have also been discussed. (author)

Adaptive responses induced in bone marrow and blood of the rats by tritium contamination

International Nuclear Information System (INIS)

Savu, D.I.; Ionescu, M.A.; Petcu, I.

2000-01-01

It has been more than a decade since the initial report on the phenomenon termed 'adaptive response to ionizing radiation'. Although a number of reports have appeared since then, the understanding of this response is still incomplete. Our group intended to investigate whether the adaptive response could be induced in vivo by low level internal tritium contamination of rats and subsequently exposed to challenging irradiations with fast neutrons or gamma rays. Two experiments were performed and analysed comparatively. In the first experiment the rats have been pre-contaminated for 3 weeks to total doses of 7 cGy and 35 cGy and subsequently irradiated to 1 Gy by fast neutrons (d(13.5)+Be). They were sacrificed after 24 hours. In the second experiment rats were exposed to high gamma irradiation (1.4 Gy) after prior contamination with tritium for 20 days to total doses of 4.4 cGy and 5.1 cGy. We followed up the modifications of two biochemical parameters: (i) the in vitro tritiated thymidine incorporation in the bone marrow cells and (ii) the reduced glutathione level in the blood cells. The thymidine incorporation assay revealed a putative adaptive reaction only for the rats preirradiated with tritiated water to 35 cGy and post-irradiated with fast neutrons. The glutathione content was found to be increased (back to the normal level) for the tritium pre-contaminated and neutron irradiated animals as compared to those exposed only to fast neutrons. The adaptive response is believed to be a protective mechanism that confers resistance to the detrimental effects of ionizing radiation. Our studies suggest that the irradiation with low conditioning doses of tritium (7; 35 cGy) is more efficient in conferring radioresistance to bone marrow and blood cells at the treatment with fast neutrons (1 Gy) than the irradiation with tritium doses of 4.4 and 5.1 cGy followed by gamma rays (1.4 Gy). (authors)

Tritium permeation through helium-heated steam generators of ceramic breeder blankets for DEMO

International Nuclear Information System (INIS)

Fuetterer, M.A.; Raepsaet, X.; Proust, E.

1994-01-01

The specifications of permeation barriers, tritium recovery process maintaining a very low tritium activity in the coolant, and control of the coolant chemistry, required the evaluation of the tritium losses through the steam generators and include the definition of its operating conditions by thermodynamic cycle calculations and its thermal-hydraulic design. For both tasks specific computer tools were developed. The obtained geometry, surface area, and temperature profiles along the heat exchanger tubes were then used to estimate the daily tritium permeation into the steam cycle. Steam oxidized Incoloy 800 austenitic stainless steel was identified as the best suited existing material; in nominal steady-state operation, the tritium escape into the steam cycle could be restricted to less than 10 Ci/d. Tritium permeation during temperature and pressure transients in the steam generator (destruction and possible self-healing of the permeation barrier) is identified to bear a large tritium release potential. Solutions are proposed. (from authors). 4 figs., 1 tab