WorldWideScience

Sample records for irradiated tantalum target

  1. Post-irradiation analysis of the tantalum container of an ISOLDE LBE target

    CERN Document Server

    Noah, E; Bruetsch, R; Catherall, R; Gavillet, D; Krbanjevic, J; Linder, H P; Martin, M; Neuhausen, J; Schumann, D; Stora, T; Zanini, L

    2012-01-01

    CERN-ISOLDE operates a range of oxides, carbides, refractory metal foils and liquid metal targets for the production of radioactive ion beams. Following irradiation with a pulsed beam of 1 GeV and 1.4 GeV protons at temperatures reaching 600 degrees C, the tantalum container of a liquid lead bismuth eutectic (LBE) target was examined. A thin layer of Pb/Bi was observed on the inner surface of the container. A sample of the surface prepared using the focused ion beam technique was investigated using SEM and EDX. Results show a higher concentration of bismuth at the interface with tantalum and micron-sized cracks in the tantalum filled with LBE. Implications of these results for the lifetime of the target container which has been known to fail under pulsed beam operation are discussed. (C) 2011 Elsevier B.V. All rights reserved.

  2. Hafnium radioisotope recovery from irradiated tantalum

    Science.gov (United States)

    Taylor, Wayne A.; Jamriska, David J.

    2001-01-01

    Hafnium is recovered from irradiated tantalum by: (a) contacting the irradiated tantalum with at least one acid to obtain a solution of dissolved tantalum; (b) combining an aqueous solution of a calcium compound with the solution of dissolved tantalum to obtain a third combined solution; (c) precipitating hafnium, lanthanide, and insoluble calcium complexes from the third combined solution to obtain a first precipitate; (d) contacting the first precipitate of hafnium, lanthanide and calcium complexes with at least one fluoride ion complexing agent to form a fourth solution; (e) selectively adsorbing lanthanides and calcium from the fourth solution by cationic exchange; (f) separating fluoride ion complexing agent product from hafnium in the fourth solution by adding an aqueous solution of ferric chloride to obtain a second precipitate containing the hafnium and iron; (g) dissolving the second precipitate containing the hafnium and iron in acid to obtain an acid solution of hafnium and iron; (h) selectively adsorbing the iron from the acid solution of hafnium and iron by anionic exchange; (i) drying the ion exchanged hafnium solution to obtain hafnium isotopes. Additionally, if needed to remove residue remaining after the product is dried, dissolution in acid followed by cation exchange, then anion exchange, is performed.

  3. Fabrication of a tantalum-clad tungsten target for LANSCE

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, A.T., E-mail: atnelson@lanl.gov [Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); O' Toole, J.A.; Valicenti, R.A. [Accelerator Operations and Technology Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Maloy, S.A. [Civilian Nuclear Program Office, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States)

    2012-12-15

    Development of a solid state bonding technique suitable to clad tungsten targets with tantalum was completed to improve operation of the Los Alamos Neutron Science Centers spallation target. Significant deterioration of conventional bare tungsten targets has historically resulted in transfer of tungsten into the cooling system through corrosion resulting in increased radioactivity outside the target and reduction of delivered neutron flux. The fabrication method chosen to join the tantalum cladding to the tungsten was hot isostatic pressing (HIP) given the geometry constraints of a cylindrical assembly and previous success demonstrated at KENS. Nominal HIP parameters of 1500 Degree-Sign C, 200 MPa, and 3 h were selected based upon previous work. Development of the process included significant surface engineering controls and characterization given tantalums propensity for oxide and carbide formation at high temperatures. In addition to rigorous acid cleaning implemented at each step of the fabrication process, a three layer tantalum foil gettering system was devised such that any free oxygen and carbon impurities contained in the argon gas within the HIP vessel was mitigated to the extent possible before coming into contact with the tantalum cladding. The result of the numerous controls and refined techniques was negligible coarsening of the native Ta{sub 2}O{sub 5} surface oxide, no measureable oxygen diffusion into the tantalum bulk, and no detectable carburization despite use of argon containing up to 5 ppm oxygen and up to 40 ppm total CO, CO{sub 2}, or organic contaminants. Post bond characterization of the interface revealed continuous bonding with a few microns of species interdiffusion.

  4. Fabrication of a tantalum-clad tungsten target for LANSCE

    Science.gov (United States)

    Nelson, A. T.; O'Toole, J. A.; Valicenti, R. A.; Maloy, S. A.

    2012-12-01

    Development of a solid state bonding technique suitable to clad tungsten targets with tantalum was completed to improve operation of the Los Alamos Neutron Science Centers spallation target. Significant deterioration of conventional bare tungsten targets has historically resulted in transfer of tungsten into the cooling system through corrosion resulting in increased radioactivity outside the target and reduction of delivered neutron flux. The fabrication method chosen to join the tantalum cladding to the tungsten was hot isostatic pressing (HIP) given the geometry constraints of a cylindrical assembly and previous success demonstrated at KENS. Nominal HIP parameters of 1500 °C, 200 MPa, and 3 h were selected based upon previous work. Development of the process included significant surface engineering controls and characterization given tantalums propensity for oxide and carbide formation at high temperatures. In addition to rigorous acid cleaning implemented at each step of the fabrication process, a three layer tantalum foil gettering system was devised such that any free oxygen and carbon impurities contained in the argon gas within the HIP vessel was mitigated to the extent possible before coming into contact with the tantalum cladding. The result of the numerous controls and refined techniques was negligible coarsening of the native Ta2O5 surface oxide, no measureable oxygen diffusion into the tantalum bulk, and no detectable carburization despite use of argon containing up to 5 ppm oxygen and up to 40 ppm total CO, CO2, or organic contaminants. Post bond characterization of the interface revealed continuous bonding with a few microns of species interdiffusion.

  5. The effect of low energy helium ion irradiation on tungsten-tantalum (W-Ta) alloys under fusion relevant conditions

    Science.gov (United States)

    Gonderman, S.; Tripathi, J. K.; Novakowski, T. J.; Sizyuk, T.; Hassanein, A.

    2017-08-01

    Currently, tungsten remains the best candidate for plasma-facing components (PFCs) for future fusion devices because of its high melting point, low erosion, and strong mechanical properties. However, continued investigation has shown tungsten to undergo severe morphology changes under fusion-like conditions. These results motivate the study of innovative PFC materials which are resistant to surface morphology evolution. The goal of this work is to examine tungsten-tantalum (W-Ta) alloys, a potential PFC material, and their response to low energy helium ion irradiation. Specifically, W-Ta samples are exposed to 100 eV helium irradiations with a flux of 1.15 × 1021 ions m-2 s-1, at 873 K, 1023 K, and 1173 K for 1 h duration. Scanning electron microscopy (SEM) reveals significant changes in surface deterioration due to helium ion irradiation as a function of both temperature and tantalum concentration in W-Ta samples. X-Ray Diffraction (XRD) studies show a slight lattice parameter expansion in W-Ta alloy samples compared to pure W samples. The observed lattice parameter expansion in W-Ta alloy samples (proportional to increasing Ta wt.% concentrations) reflect significant differences observed in the evolution of surface morphology, i.e., fuzz development processes for both increasing Ta wt.% concentration and target temperature. These results suggest a correlation between the observed morphology differences and the induced crystal structure change caused by the presence of tantalum. Shifts in the XRD peaks before and after 100 eV helium irradiation with a flux of 1.15 × 1021 ions m-2 s-1, 1023 K, for 1 h showed a significant difference in the magnitude of the shift. This has suggested a possible link between the atomic spacing of the material and the accumulated damage. Ongoing research is needed on W-Ta alloys and other innovative materials for their application as irradiation resistant materials in future fusion or irradiation environments.

  6. The development of fast tantalum foil targets for short-lived isotopes

    Energy Technology Data Exchange (ETDEWEB)

    Bennett, J.R.J. E-mail: roger.bennett@rl.ac.uk; Bergmann, U.C.; Drumm, P.V.; Ravn, H

    2003-05-01

    The most recent developments of fast tantalum foil targets for short-lived isotopes are described and the performance of the targets at ISOLDE with beams of {sup 11}Li, {sup 12}Be and {sup 14}Be is given.

  7. Target irradiation experiments. [Hydra accelerator

    Energy Technology Data Exchange (ETDEWEB)

    1976-01-01

    Target irradiation experiments have been carried out on the Hydra accelerator, operating at powers between 0.15 and 0.3 TW. As listed in Table I, four types of spherical shell targets have been studied: 3 mm diameter, 200 ..mu..m and 50 ..mu..m wall thickness Au targets; 3 mm diameter, 300 ..mu..m wall thickness plastic targets; and 0.85 mm diameter, 10 ..mu..m wall thickness Ni targets. When compared to a practical range for 700 keV electrons, the ratio of shell thickness to electron range varied between 0.03 for the Ni targets to 1.5 for the thick walled Au targets. Multiple exposure optical holography was utilized to determine ablator velocity, and a one-dimensional hydrodynamical materials code CHARTD was utilized to model target response and infer beam deposition. Energy deposition varied from 1 TW/gm for thick Au targets up to 8 TW/gm for thin Ni targets, and pusher velocities ranged between 0.5 and 3.5 cm/..mu..sec. Neutron production from D/sub 2/ and DT filled Ni exploding pusher targets was measured using Ag and Li activation counters and gated scintillator photomultiplier time of flight detectors.

  8. Measurement of the production of charged pions by protons on a tantalum target

    CERN Document Server

    Catanesi, M.G.; Edgecock, R.; Ellis, Malcolm; Robbins, S.; Soler, F.J.P.; Gossling, C.; Bunyatov, S.; Krasnoperov, A.; Popov, B.; Serdiouk, V.; Tereschenko, V.; Di Capua, E.; Vidal-Sitjed, G.; Artamonov, A.; Arce, P.; Giani, S.; Gilardoni, S.; Gorbunov, P.; Grant, A.; Grossheim, A.; Gruber, P.; Ivanchenko, V.; Kayis-Topaksu, A.; Panman, J.; Papadopoulos, I.; Pasternak, J.; Tcherniaev, E.; Tsukerman, I.; Veenhof, R.; Wiebusch, C.; Zucchelli, P.; Blondel, A.; Borghi, S.; Campanelli, M.; Morone, M.C.; Prior, G.; Schroeter, R.; Engel, R.; Meurer, C.; Kato, I.; Gastaldi, U.; Mills, G.B.; Graulich, J.S.; Gregoire, G.; Bonesini, M.; De Min, A.; Ferri, F.; Paganoni, M.; Paleari, F.; Kirsanov, M.; Bagulya, A.; Grichine, V.; Polukhina, N.; Palladino, V.; Coney, L.; Schmitz, D.; Barr, G.; De Santo, A.; Pattison, C.; Zuber, K.; Bobisut, F.; Gibin, D.; Guglielmi, A.; Mezzetto, M.; Dumarchez, J.; Vannucci, F.; Dore, U.; Orestano, D.; Pastore, F.; Tonazzo, A.; Tortora, L.; Booth, C.; Buttar, C.; Hodgson, P.; Howlett, L.; Bogomilov, M.; Chizhov, M.; Kolev, D.; Tsenov, R.; Apollonio, M.; Chimenti, P.; Giannini, G.; Santin, G.; Burguet-Castell, J.; Cervera-Villanueva, A.; Gomez-Cadenas, J.J.; Martin-Albo, J.; Novella, P.; Sorel, M.; Tornero, A.

    2007-01-01

    A measurement of the double-differential cross-section for the production of charged pions in proton--tantalum collisions emitted at large angles from the incoming beam direction is presented. The data were taken in 2002 with the HARP detector in the T9 beam line of the CERN PS. The pions were produced by proton beams in a momentum range from 3 \\GeVc to 12 \\GeVc hitting a tantalum target with a thickness of 5% of a nuclear interaction length. The angular and momentum range covered by the experiment ($100 \\MeVc \\le p < 800 \\MeVc$ and $0.35 \\rad \\le \\theta <2.15 \\rad$) is of particular importance for the design of a neutrino factory. The produced particles were detected using a small-radius cylindrical time projection chamber (TPC) placed in a solenoidal magnet. Track recognition, momentum determination and particle identification were all performed based on the measurements made with the TPC. An elaborate system of detectors in the beam line ensured the identification of the incident particles. Results a...

  9. Measurement of the production of charged pions by protons on a tantalum target

    CERN Document Server

    Catanesi, M G; Edgecock, R; Ellis, M; Robbins, S; Soler, F J P; Gössling, C; Bunyatov, S; Krasnoperov, A V; Popov, B; Serdiouk, V; Tereshchenko, V V; Di Capua, E; Vidal-Sitjes, G; Artamonov, A; Arce, P; Giani, S; Gilardoni, S; Gorbunov, P; Grant, A; Grossheim, A; Gruber, P; Ivanchenko, V; Kayis-Topaksu, A; Panman, J; Papadopoulos, I; Pasternak, J; Chernyaev, E; Tsukerman7, I; Veenhof, R; Wiebusch, C; Zucchelli, P; Blondel, A; Borghi, S; Campanelli, M; Morone, M C; Prior, G; Schroeter, R; Engel, R; Meurer, C; Kato, I; Gastaldi, Ugo; Mills, G B; Graulich, J S; Grgoire, G; Bonesini, M; De Min, A; Ferri, F; Paganoni, M; Paleari, F; Kirsanov, M; Bagulya, A; Grichine, V; Polukhina, N; Palladino, V; Coney, L; Schmitz, D; Barr, G; De Santo, A; Pattison, C; Zuber, K; Bobisut, F; Gibin, D; Guglielmi, Alberto M; Mezzetto, M; Dumarchez, J; Vannucci, F; Dore, U; Orestano, D; Pastore, F; Tonazzo, A; Tortora, L; Booth, C; Buttar, C; Hodgson, P; Howlett, L; Bogomilov, M; Chizhov, M; Kolev, D; Tsenov, R; Piperov, S; Temnikov, P; Apollonio, M; Chimenti, P; Giannini, G; Santin, G; Burguet-Castell, J; Cervera-Villanueva, Anselmo; Gómez-Cadenas, J J; Martín-Albo, J; Novella, P; Sorel, M; Tornero, A

    2007-01-01

    A measurement of the double-differential cross-section for the production of charged pions in proton--tantalum collisions emitted at large angles from the incoming beam direction is presented. The data were taken in 2002 with the HARP detector in the T9 beam line of the CERN PS. The pions were produced by proton beams in a momentum range from 3 \\GeVc to 12 \\GeVc hitting a tantalum target with a thickness of 5% of a nuclear interaction length. The angular and momentum range covered by the experiment ($100 \\MeVc \\le p < 800 \\MeVc$ and $0.35 \\rad \\le \\theta <2.15 \\rad$) is of particular importance for the design of a neutrino factory. The produced particles were detected using a small-radius cylindrical time projection chamber (TPC) placed in a solenoidal magnet. Track recognition, momentum determination and particle identification were all performed based on the measurements made with the TPC. An elaborate system of detectors in the beam line ensured the identification of the incident particles. Results a...

  10. Uranium briquettes for irradiation target

    Energy Technology Data Exchange (ETDEWEB)

    Saliba-Silva, Adonis Marcelo; Garcia, Rafael Henrique Lazzari; Martins, Ilson Carlos; Carvalho, Elita Fontenele Urano de; Durazzo, Michelangelo, E-mail: saliba@ipen.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2011-07-01

    Direct irradiation on targets inside nuclear research or multiple purpose reactors is a common route to produce {sup 99}Mo-{sup 99m}Tc radioisotopes. Nevertheless, since the imposed limits to use LEU uranium to prevent nuclear armament production, the amount of uranium loaded in target meats has physically increased and new processes have been proposed for production. Routes using metallic uranium thin film and UAl{sub x} dispersion have been used for this purpose. Both routes have their own issues, either by bringing difficulties to disassemble the aluminum case inside hot cells or by generating great amount of alkaline radioactive liquid rejects. A potential route might be the dispersion of powders of LEU metallic uranium and nickel, which are pressed as a blend inside a die and followed by pulse electroplating of nickel. The electroplating provides more strength to the briquettes and creates a barrier for gas evolution during neutronic disintegration of {sup 235}U. A target briquette platted with nickel encapsulated in an aluminum case to be irradiated may be an alternative possibility to replace other proposed targets. This work uses pulse Ni-electroplating over iron powder briquette to simulate the covering of uranium by nickel. The following parameters were applied 10 times for each sample: 900Hz, -0.84A/square centimeters with duty cycle of 0.1 in Watts Bath. It also presented the optical microscopy analysis of plated microstructure section. (author)

  11. Design and development of a tantalum foil target for the production of high intensity radioactive beams

    CERN Document Server

    Densham, Cristopher John

    2000-01-01

    The design and development of a high power target and ion source for the production of Radioactive Beams at intensities approaching two orders of magnitude greater than currently possible is presented. This was a key aim of the RIST experiment, designed to utilise the proton synchrotron of the ISIS facility at Rutherford Appleton laboratory, Chilton, Oxfordshire, where an 800 MeV proton beam is available at currents of up to 200 mu A. A number of different target designs were considered and analysed, and high temperature power dissipation tests were conducted. This culminated in the manufacture of a diffusion bonded structure comprising 6000 separate tantalum foil discs and spacer washers. The target was installed in the RIST facility, and thermal tests using electron beam heating demonstrated that the target was capable of dissipating 24 kW by thermal radiation, at the desired temperature of 2000 deg C. This is equivalent to running with the 800 MeV ISIS proton beam at a current of 100 mu A. A smaller diamet...

  12. Target and structural materials under dual-beam irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Camus, E.; Wanderka, N.; Wollenberger, H. [Hahn-Meitner-Institut Berlin GmbH (Germany)

    1995-11-01

    The European Spallation Source (ESS) is planned to have a beam power of 5 MW (3.75 mA of 1.334 GeV protons). This is by a factor 30 higher than the available most powerful spallation source ISIS at Rutherford-Appleton Lab. (RAL) in Great-Britain. This causes a damage rate of approx. 10 dpa (displacements per atom) per month in target materials (W or Ta) or structural materials. The problem of radiation damage by high energy protons in different alloys has been recently reviewed. At HMI, simulation irradiation using heavy ions and helium or hydrogen ions at the dual-beam facility are being out. Here, we report on some preliminary results obtained on tantalum as target material and on ferritic/martensitic steels (HT9 type steels or comparable steels), which are proposed to be used as structural materials. Goal of these investigations is to correlate the results with those obtained at spallation irradiated specimens and to investigate the unexplored field of simultaneous production of damage, helium and hydrogen at high levels. (author) 4 figs., 1 tab., 9 refs.

  13. Calculation of electron emission from a tantalum foil irradiated by 100-kV and 50-kV x-rays

    Energy Technology Data Exchange (ETDEWEB)

    Berger, M.J.

    1998-03-01

    Two Monte Carlo programs, XITRAN and XMTRAN, were developed for calculating the emission of electrons from high-Z foils irradiated with x rays. XITRAN follows all individual elastic collisions of electrons with atoms, whereas XMTRAN uses the condensed-random-walk model. Both codes take into account photo-electrons, fluorescence radiation, and Auger electrons. Comparisons are made with an experiment by Dolan at Sandia Laboratories involving the backward and forward emission of electrons from a tantalum foil irradiated by 100-kV and 50-kV x-ray beams. There is good agreement between results from the XITRAN and XMTRAN codes. There emitted per incident x-ray photon, and in regard to the angular distribution of the emerging electrons. In regard to the electron energy spectra, there is fair agreement down to a spectral energy of 20 keV, whereas below 20 keV the calculated spectra lie considerably below the measurements.

  14. Comparative analysis of anodized, implanted and sputtered tantalum oxide targets for the study of {sup 16}O+{sup 16}O fusion reaction

    Energy Technology Data Exchange (ETDEWEB)

    Silva, H., E-mail: hugo_miguel_m_silva@hotmail.com [Departamento de Física, Faculdade de Ciências e Tecnologia, Universidade Nova de Lisboa, 2829-516 Caparica (Portugal); Centro de Física Nuclear da Universidade de Lisboa, Av. Prof. Gama Pinto, 1649-003 Lisboa (Portugal); Instituto Superior Técnico, Campus Tecnológico e Nuclear, Universidade Técnica de Lisboa, Estrada Nacional 10, 2686-953 Sacavém (Portugal); Cruz, J. [Departamento de Física, Faculdade de Ciências e Tecnologia, Universidade Nova de Lisboa, 2829-516 Caparica (Portugal); Centro de Física Nuclear da Universidade de Lisboa, Av. Prof. Gama Pinto, 1649-003 Lisboa (Portugal); Instituto Superior Técnico, Campus Tecnológico e Nuclear, Universidade Técnica de Lisboa, Estrada Nacional 10, 2686-953 Sacavém (Portugal); Redondo-Cubero, A. [Instituto Superior Técnico, Campus Tecnológico e Nuclear, Universidade Técnica de Lisboa, Estrada Nacional 10, 2686-953 Sacavém (Portugal); and others

    2014-07-15

    Measuring the total cross section of a fusion reaction in the region of astrophysical interest, such as the {sup 16}O+{sup 16}O fusion reaction, is a real challenge due the very small cross sections involved and the large number of possible exit channels. Taking into account these difficulties, the use of targets with known thickness, stoichiometry and minimal contamination that can withstand high beam currents is required. In this study, we report the comparison between three different types of targets for the study of this fusion reaction, such as anodized, implanted and sputtered tantalum oxide targets and the results show that the anodized and sputtered targets are more suitable for this study due to their higher oxygen density and to the formation of a stable oxide compound, tantalum pentoxide (Ta{sub 2}O{sub 5})

  15. The tantalum-cased tantalum capacitor

    Science.gov (United States)

    Moynihan, J. D.

    1977-01-01

    Tantalum-cased tantalum capacitors were tested with regard to temperature stability, capacitance ratio, surge current capabilities, shock, vibration, and thermal shock. They were found to be superior to the conventional wet slug tantalum capacitor cased in silver, since they are more resistant to sulfuric acid. The tantalum-cased tantalum capacitors are widely accepted for use in critical electronic equipment because of their excellent performance and reliability.

  16. Irradiation of target volumes with concave outlines

    Energy Technology Data Exchange (ETDEWEB)

    De Neve, W.; Fortan, L.; Derycke, S.; Van Duyse, B.; DE Wagter, C. [Ghent Rijksuniversiteit (Belgium). Kliniek voor Radiotherapie en Kerngeneeskunde

    1995-12-01

    A heuristic planning procedure allowing to obtain a 3-dimensional conformal dose distribution for target volumes with concavities has been investigated. The procedure divides the planning problem into a number of sub-problems each solvable by known methods. By patching together the solutions to the sub-problems, a solution with a predictable dosimetric outcome can be obtained. The procedure can be applied to most 3-dimensional systems. The procedure is described and its applications to the irradiation of neoplasms are discussed. (A.S.).

  17. Photoionization of an aluminum plasma by a tantalum X source

    Science.gov (United States)

    Renaudin, Patrick; Back, Christina A.; Chenais-Popovics, Claude; Audebert, Patrick; Geindre, Jean-Paul; Gauthier, Jean-Claude

    1991-05-01

    Photoionization of a helium like aliminum plasma is carried out by an external x-source. The laser beam used corresponds to the 3d to 4F transition level of tantalum. The experimental spectrum of tantalum is shown superimposed over the emission spectrum of aluminum on diagrammatic form. Good correspondence is seen between the 3d to 4F emissions of tantalum and helium like aluminum. Plasma pumping is obtained by exposure of a tantalum target to laser rays.

  18. Thermal Convection on an Irradiated Target

    Science.gov (United States)

    Mehmedagic, Igbal; Thangam, Siva

    2016-11-01

    The present work involves the computational modeling of metallic targets subject to steady and high intensity heat flux. The ablation and associated fluid dynamics when metallic surfaces are exposed to high intensity laser fluence at normal atmospheric conditions is modelled. The incident energy from the laser is partly absorbed and partly reflected by the surface during ablation and subsequent vaporization of the melt. Computational findings based on effective representation and prediction of the heat transfer, melting and vaporization of the targeting material as well as plume formation and expansion are presented and discussed in the context of various ablation mechanisms, variable thermo-physical and optical properties, plume expansion and surface geometry. The energy distribution during the process between the bulk and vapor phase strongly depends on optical and thermodynamic properties of the irradiated material, radiation wavelength, and laser intensity. The relevance of the findings to various manufacturing processes as well as for the development of protective shields is discussed. Funded in part by U. S. Army ARDEC, Picatinny Arsenal, NJ.

  19. The BLAIRR Irradiation Facility Hybrid Spallation Target Optimization

    Energy Technology Data Exchange (ETDEWEB)

    Simos N.; Hanson A.; Brown, D.; Elbakhshawn, M.

    2016-04-11

    BLAIRR STUDY STATUS OVERVIEW Beamline Complex Evaluation/Assessment and Adaptation to the Goals Facility Radiological Constraints ? Large scale analyses of conventional facility and integrated shield (concrete, soil)Target Optimization and Design: Beam-target interaction optimization Hadronic interaction and energy deposition limitations Single phase and Hybrid target concepts Irradiation Damage Thermo-mechanical considerations Spallation neutron fluence optimization for (a) fast neutron irradiation damage (b) moderator/reflector studies, (c) NTOF potential and optimization (d) mono-energetic neutron beam

  20. Specific Activity and Impurities in Irradiated Natural Nickel Target

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    In this paper, the specific activity of the 63Ni which is produced by irradiating natural nickel in a nuclear reactor is calculated. And in the 1 g irradiated natural nickel target, the species of the key impurity nuclides were analyzed,

  1. Erosion of Copper Target Irradiated by Ion Beam

    CERN Document Server

    Polosatkin, S V; Grishnyaev, E S; Konstantinov, S G; Shoshin, A A

    2012-01-01

    Erosion of copper target irradiated by deuterium ion beam with ultimate fluence is studied. The target originally destined for neutron generation represents bulk copper substrate covered by 3-\\mum titanium layer. The target was irradiated by deuterium ion beam generated in Bayard-Alpert type ion source with energy of ions 17.5 keV/nuclear. Maximal fluence in the center of the target achieves 2.5x10^23atoms/cm^2. Measurements of the profile of irradiated target and estimation of fluence shows that physical sputtering is a dominating process that determines the target erosion Most interesting feature is growth of \\mum-size tadpole-shaped structures, localized in the cracks of the surface. RFA analysis of these structures showed extremely large (up to 60%at.) carbon content.

  2. Measurement of Volatile Radionuclides Production and Release Yields followed by a Post-Irradiation Analysis of a Pb/Bi Filled Ta Target at ISOLDE

    Science.gov (United States)

    Zanini, L.; Köster, U.; David, J. C.; Tall, Y.; Andersson, M.; Berg, K.; Cormon, S.; Fallot, M.; Foucher, Y.; Frånberg, H.; Gröschel, F.; Guertin, A.; Kirchner, T.; Leray, S.; Manfrin, E.; Noah, E.; Ravn, H.; Stora, T.; Thiollière, N.; Wohlmuther, M.

    2014-05-01

    A crucial requirement in the development of liquid-metal spallation neutron target is knowledge of the composition and amount of volatile radionuclides that are released from the target during operation. It is also important to know the total amount produced, which could be released if there was an accident. One type is the lead-bismuth eutectic (LBE) target where different radionuclides can be produced following interaction with a high-energy proton beam, notably noble gases (Ar, Kr, Xe isotopes) and other relative volatile isotopes such as Hg and At. The results of an irradiation experiment performed at ISOLDE on a LBE target are compared with predictions from the MCNPX code using the latest developments on the Liège Intranuclear Cascade model (INCL4.6) and the CEM03 model. The calculations are able to reproduce the mass distribution of the radioisotopes produced, including the At production, where there is a significant contribution from secondary reactions. Subsequently, a post-irradiation examination of the irradiated target was performed. Investigations of both the tantalum target structure, in particular the beam window, and the lead-bismuth eutectic were performed using several experimental techniques. No sign of severe irradiation damage, previously observed in other ISOLDE targets, was found.

  3. Measurements of attenuation lengths through concrete and iron for neutrons produced by 800-MeV proton on tantalum target at ISIS

    CERN Document Server

    Nunomiya, T; Wright, P; Nakamura, T; Kim, E; Kurosawa, T; Taniguchi, S; Sasaki, M; Iwase, H; Uwamino, Y; Shibata, T; Ito, S; Perry, D R

    2002-01-01

    A deep penetration experiment through a thick bulk shield was performed at an intense spallation neutron source facility, ISIS, of the Rutherford Appleton Laboratory (RAL), United Kingdom. ISIS is a 800 MeV-200 mu A proton accelerator facility. Neutrons are produced from a tantalum target, and are shielded with approximately 3-m thick steel and 1-m thick ordinary concrete. On top of the shield, we measured the neutron flux attenuation through concrete and iron shields, which were additionally placed up to 120-cm and 60-cm thickness, respectively, using activation detectors of graphite and bismuth. The attenuation lengths of concrete and iron for high-energy neutrons above 20 MeV were obtained from the sup 1 sup 2 C(n, 2n) sup 1 sup 1 C reaction of graphite.

  4. Packed bed carburization of tantalum and tantalum alloy

    Science.gov (United States)

    Lopez, Peter C.; Rodriguez, Patrick J.; Pereyra, Ramiro A.

    1999-01-01

    Packed bed carburization of a tantalum or tantalum alloy object. A method for producing corrosion-resistant tantalum or tantalum alloy objects is described. The method includes the steps of placing the object in contact with a carburizing pack, heating the packed object in vacuum furnace to a temperature whereby carbon from the pack diffuses into the object forming grains with tantalum carbide along the grain boundaries, and etching the surface of the carburized object. This latter step removes tantalum carbides from the surface of the carburized tantalum object while leaving the tantalum carbide along the grain boundaries.

  5. Thermal hydraulic design and decay heat removal of a solid target for a spallation neutron source

    Energy Technology Data Exchange (ETDEWEB)

    Takenaka, N. [Department of Mechanical Engineering, Kobe University, Kobe (Japan)]. E-mail: takenaka@mech.kobe-u.ac.jp; Nio, D. [Hokkaido University, Sapporo (Japan); Kiyanagi, Y. [Hokkaido University, Sapporo (Japan); Mishima, K. [Kyoto University Research Reactor Institute, Kumatori (Japan); Kawai, M. [High Energy Accelerator Research Institute, Tsukuba (Japan); Furusaka, M. [High Energy Accelerator Research Institute, Tsukuba (Japan)

    2005-08-01

    Thermal hydraulic design and thermal stress calculations were conducted for a water-cooled solid target irradiated by a MW-class proton beam for a spallation neutron source. Plate type and rod bundle type targets were examined. The thickness of the plate and the diameter of the rod were determined based on the maximum and the wall surface temperature. The thermal stress distributions were calculated by a finite element method (FEM). The neutronics performance of the target is roughly proportional to its average density. The averaged densities of the designed targets were calculated for tungsten plates, tantalum-clad tungsten plates, tungsten rods sheathed by tantalum and Zircaloy and they were compared with mercury density. It was shown that the averaged density was highest for the tungsten plates and was high for the tantalum cladding tungsten plates, the tungsten rods sheathed by tantalum and Zircaloy in order. They were higher than or equal to that of mercury for the 1-2 MW proton beams. Tungsten target without the cladding or the sheath is not practical due to corrosion by water under irradiation condition. Therefore, the tantalum cladding tungsten plate already made successfully by HIP and the sheathed tungsten rod are the candidate of high performance solid targets. The decay heat of each target was calculated. It was low enough low compared to that of ISIS for the target without tantalum but was about four times as high as that of ISIS when the thickness of the tantalum cladding was 0.5 mm. Heat removal methods of the decay heat with tantalum were examined. It was shown that a special cooling system was required for the target exchange when tantalum was used for the target. It was concluded that the tungsten rod target sheathed with stainless steel or Zircaloy was the most reliable from the safety considerations and had similar neutronics performance to that of mercury.

  6. Thermal hydraulic design and decay heat removal of a solid target for a spallation neutron source

    Science.gov (United States)

    Takenaka, N.; Nio, D.; Kiyanagi, Y.; Mishima, K.; Kawai, M.; Furusaka, M.

    2005-08-01

    Thermal hydraulic design and thermal stress calculations were conducted for a water-cooled solid target irradiated by a MW-class proton beam for a spallation neutron source. Plate type and rod bundle type targets were examined. The thickness of the plate and the diameter of the rod were determined based on the maximum and the wall surface temperature. The thermal stress distributions were calculated by a finite element method (FEM). The neutronics performance of the target is roughly proportional to its average density. The averaged densities of the designed targets were calculated for tungsten plates, tantalum clad tungsten plates, tungsten rods sheathed by tantalum and Zircaloy and they were compared with mercury density. It was shown that the averaged density was highest for the tungsten plates and was high for the tantalum cladding tungsten plates, the tungsten rods sheathed by tantalum and Zircaloy in order. They were higher than or equal to that of mercury for the 1 2 MW proton beams. Tungsten target without the cladding or the sheath is not practical due to corrosion by water under irradiation condition. Therefore, the tantalum cladding tungsten plate already made successfully by HIP and the sheathed tungsten rod are the candidate of high performance solid targets. The decay heat of each target was calculated. It was low enough low compared to that of ISIS for the target without tantalum but was about four times as high as that of ISIS when the thickness of the tantalum cladding was 0.5 mm. Heat removal methods of the decay heat with tantalum were examined. It was shown that a special cooling system was required for the target exchange when tantalum was used for the target. It was concluded that the tungsten rod target sheathed with stainless steel or Zircaloy was the most reliable from the safety considerations and had similar neutronics performance to that of mercury.

  7. Post-Irradiation Examination of Array Targets - Part I

    Energy Technology Data Exchange (ETDEWEB)

    Icenhour, A.S.

    2004-01-23

    During FY 2001, two arrays, each containing seven neptunium-loaded targets, were irradiated at the Advanced Test Reactor in Idaho to examine the influence of multi-target self-shielding on {sup 236}Pu content and to evaluate fission product release data. One array consisted of seven targets that contained 10 vol% NpO{sub 2} pellets, while the other array consisted of seven targets that contained 20 vol % NpO{sub 2} pellets. The arrays were located in the same irradiation facility but were axially separated to minimize the influence of one array on the other. Each target also contained a dosimeter package, which consisted of a small NpO{sub 2} wire that was inside a vanadium container. After completion of irradiation and shipment back to the Oak Ridge National Laboratory, nine of the targets (four from the 10 vol% array and five from the 20 vol% array) were punctured for pressure measurement and measurement of {sup 85}Kr. These nine targets and the associated dosimeters were then chemically processed to measure the residual neptunium, total plutonium production, {sup 238}Pu production, and {sup 236}Pu concentration at discharge. The amount and isotopic composition of fission products were also measured. This report provides the results of the processing and analysis of the nine targets.

  8. Facile synthesis of efficient photocatalytic tantalum nitride nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Zheng; Wang, Jiangting; Hou, Jungang; Huang, Kai; Jiao, Shuqiang [School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Zhu, Hongmin, E-mail: hzhu@ustb.edu.cn [School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083 (China)

    2012-11-15

    Graphical abstract: Tantalum nitride nanoparticles as a visible-light-driven photocatalyst prepared by a novel homogeneously chemical reduction of tantalum pentachloride using sodium in liquid ammonia and the morphologies, visible-light photocatalytic properties and stability of tantalum nitride nanoparticles were investigated. Highlights: ► Tantalum nitride nanoparticles have been prepared by a homogeneously chemical reduction. ► The crystal structure of tantalum nitride was determined by Rietveld refinement and XRD patterns. ► The Tantalum nitride nanoparticle size was in the range of 20–50 nm. ► Much high photocatalytic activities of Ta{sub 3}N{sub 5} nanoparticles were obtained under visible-light irradiation. -- Abstract: Tantalum nitride nanoparticles, as visible-light photocatalysts were synthesized by a two-step homogeneously chemical reduction without any polymers and templates. The well-crystallized Ta{sub 3}N{sub 5} nanoparticles with a range of 20–50 nm in size have been characterized by a number of techniques, such as XRD, XPS, SEM, TEM, BET and UV–Vis spectrum. Most importantly, the Ta{sub 3}N{sub 5} nanoparticles with good stability exhibited higher photooxidation activities in the water splitting and degradation of methylene blue under visible light irradiation than bulk Ta{sub 3}N{sub 5} particles and commercial P25 TiO{sub 2}, demonstrating that Ta{sub 3}N{sub 5} nanoparticle is a promising candidate as a visible-light photocatalyst.

  9. Study of Target Fragmentation in the Interaction of 86 MeV/A $^{12}$Carbon with Tantalum, Bismuth and Uranium

    CERN Multimedia

    2002-01-01

    Using radiochemical techniques we will ; a)~~measure the target fragment mass and charge distributions from the interaction of 86~MeV/A |1|2C with Ta, Bi and U; ; b)~~measure the target fragment forward momentum and average kinetic energy using the thick target-thick catcher technique for the above reactions; and ; c)~~measure the target fragment angular and differential energy distributions using thin target-thin catcher techniques for the reactions with Ta and U. \\\\ \\\\ These measurements should allow us to better characterize the transition between low energy and realistic heavy ion reaction mechanisms.

  10. Final Report on MEGAPIE Target Irradiation and Post-Irradiation Examination

    Energy Technology Data Exchange (ETDEWEB)

    Yong, Dai [Paul Scherrer-Institut (Switzerland)

    2015-06-30

    Megawatt pilot experiment (MEGAPIE) was successfully performed in 2006. One of the important goals of MEGAPIE is to understand the behaviour of structural materials of the target components exposed to high fluxes of high-energy protons and spallation neutrons in flowing LBE (liquid lead-bismuth eutectic) environment by conducting post-irradiation examination (PIE). The PIE includes four major parts: non-destructive test, radiochemical analysis of production and distribution of radionuclides produced by spallation reaction in LBE, analysis of LBE corrosion effects on structural materials, T91 and SS 316L steels, and mechanical testing of the T91 and SS 316L steels irradiated in the lower part of the target. The non-destructive test (NDT) including visual inspection and ultrasonic measurement was performed in the proton beam window area of the T91 calotte of the LBE container, the most intensively irradiated part of the MEGAPIE target. The visual inspection showed no visible failure and the ultrasonic measurement demonstrated no detectable change in thickness in the beam window area. Gamma mapping was also performed in the proton beam window area of the AlMg3 safety-container. The gamma mapping results were used to evaluate the accumulated proton fluence distribution profile, the input data for determining irradiation parameters. Radiochemical analysis of radionuclides produced by spallation reaction in LBE is to improve the understanding of the production and distribution of radionuclides in the target. The results demonstrate that the radionuclides of noble metals, 207Bi, 194Hg/Au are rather homogeneously distributed within the target, while radionuclides of electropositive elements are found to be deposited on the steel-LBE interface. The corrosion effect of LBE on the structural components under intensive irradiation was investigated by metallography. The results show that no evident corrosion damages. However, unexpected deep

  11. Target volume definition and target conformal irradiation technique for breast cancer patients

    Energy Technology Data Exchange (ETDEWEB)

    Kiricuta, I.C.; Gotz, U.; Schwab, F.; Fehn, M.; Neumann, H.H. [St. Vincenz-Hospital, Limburg (Germany). Inst. of Radiation Oncology

    2000-07-01

    The aim of this study was to present the target volume and irradiation technique in the most complex situation where the breast or chest wall and the locoregional lymphatics (mammarial internal lymph nodes, axillary and supraclavicular lymph nodes) have to be irradiated. The study comprised 125 breast cancer patients treated with curative intent after primary surgery in the last two years at our institute. In 62 cases the target volume included the breast or chest wall and the locoregional lymphatics, which were treated using our irradiation technique. The target conformal irradiation technique is a multiple non-opposed beams one isocenter technique developed to protect the heart and lungs. This technique, consisting of several rotation beams modulated with wedge filters and individual lung absorbers as well as additional fixed beams, was used in our study to apply a homogeneous dose of 46 to 56 Gy to the target volume; the irradiation technique was optimized by means of dose-volume histograms. After pre-localization, the patients underwent computerized tomographic scanning, with sections at 1.0 cm intervals. Contouring of target volume and organs at risk was carried out with a MULTIDATA workstation for regions of interest (mammarial internal and/or axillary and/or supraclavicular lymphatics and the breast or chest wall) as well as the organs at risk, such as heart and lung parenchyma. Planning target volume coverage was examined by three-dimensional isodose visualization for all CT axial sections for each patient. To determine the incidence of acute or late side effects on the lung parenchyma, conventional chest x-rays and CT studies were carried out at 1 month, 3 months and 6 months after completion of radiotherapy. Dose-volume histogram analysis revealed that this irradiation technique permits the application of a homogeneous dose to the target volume, conforming to the ICRU norms. The maximum dose applied to the ipsilateral lung parenchyma was less than 50

  12. Release studies of a thin foil tantalum target for the production of short-lived radioactive nuclei

    CERN Document Server

    Bennett, J R J; Drumm, P V; Lettry, Jacques; Nilsson, T; Catherall, R; Jonsson, O C; Ravn, H L; Simon, H

    2002-01-01

    Measurements have been made at ISOLDE, of the release curves and yields of radioactive beams of lithium, sodium and beryllium from a target constructed from 2 $\\mu$m thick foils. The release curves have been analysed by fitting to a mathematical model to determine the coefficients of diffusion of the particles in the foils and effusion through the target and ionizer at several temperatures. Through a better understanding of the rate of transport of the particles, it is possible to design targets and ionizers with improved yields. This is most important for the rare, short-lived isotopes in which there is considerable interest for physics experiments. This target has demonstrated large increases in the yields of $^{11}$Li and $^{12}$Be, in agreement with the predictions of the model. (11 refs).

  13. Release studies of a thin foil tantalum target for the production of short-lived radioactive nuclei

    Energy Technology Data Exchange (ETDEWEB)

    Bennett, J.R.J. E-mail: rjb@isise.rl.ac.uk; Bergmann, U.C.; Drumm, P.V.; Lettry, J.; Nilsson, T.; Catherall, R.; Jonsson, O.C.; Ravn, H.L.; Simon, H

    2002-04-22

    Measurements have been made at ISOLDE, of the release curves and yields of radioactive beams of lithium, sodium and beryllium from a target constructed from 2 {mu}m thick foils. The release curves have been analysed by fitting to a mathematical model to determine the coefficients of diffusion of the particles in the foils and effusion through the target and ionizer at several temperatures. Through a better understanding of the rate of transport of the particles, it is possible to design targets and ionizers with improved yields. This is most important for the rare, short-lived isotopes in which there is considerable interest for physics experiments. This target has demonstrated large increases in the yields of {sup 11}Li and {sup 12}Be, in agreement with the predictions of the model.

  14. Mitochondrial-targeted human catalase affords neuroprotection from proton irradiation.

    Science.gov (United States)

    Liao, Alicia C; Craver, Brianna M; Tseng, Bertrand P; Tran, Katherine K; Parihar, Vipan K; Acharya, Munjal M; Limoli, Charles L

    2013-07-01

    Significant past work has linked radiation exposure of the CNS to elevated levels of oxidative stress and inflammation. These secondary reactive processes are both dynamic and persistent and are believed to compromise the functionality of the CNS, in part, by disrupting endogenous neurogenesis in the hippocampus. While evidence has shown neurogenesis to be sensitive to irradiation and redox state, the mechanistic basis underlying these effects is incompletely understood. To clarify the role of reactive oxygen species (ROS) in mediating radiation-induced changes in neurogenesis we have analyzed transgenic mice that overexpress human catalase localized to the mitochondria. With this model, we investigated the consequences of low dose and clinically relevant proton irradiation on neurogenesis, and how that process is modified in response to genetic disruption of mitochondrial ROS levels. In unirradiated animals, basal neurogenesis was improved significantly by reductions in mitochondrial ROS. In animals subjected to proton exposure, hippocampal progenitor cell proliferation was attenuated significantly by overexpression of human catalase in the mitochondria. Furthermore, expression of the MCAT transgene significantly improved neurogenesis in WT animals after low-dose proton exposure (0.5 Gy), with similar trends observed at higher dose (2 Gy). Our report documents for the first time the impact of proton irradiation on hippocampal neurogenesis, and the neuroprotective properties of reducing mitochondrial ROS through the targeted overexpression of catalase. © 2013 by Radiation Research Society

  15. Radiological considerations on multi-MW targets Part II After-heat and temperature distribution in packed tantalum spheres

    CERN Document Server

    Magistris, M

    2005-01-01

    CERN is designing a Superconducting Proton Linac (SPL) to provide a 2.2GeV, 4MW proton beam to feed facilities like, for example, a future Neutrino Factory or a Neutrino SuperBeam. One of the most promising target candidates is a stationary consisting of a Ti container filled with small Ta pellets. The power deposited as heat by the radioactive nuclides (the so-called after-heat) can considerably increase the target temperature after ceasing operation, if no active cooling is provided. An estimate of the induced radioactivity and after-heat was performed with the FLUKA Monte Carlo code. To estimate the highest temperature reached inside the target, the effective thermal conductivity of packed spheres was evaluated using the basic cell method. A method for estimating the contribution to heat transmission from radiation is also discussed1).

  16. Particle therapy of moving targets-the strategies for tumour motion monitoring and moving targets irradiation.

    Science.gov (United States)

    Kubiak, Tomasz

    2016-10-01

    Particle therapy of moving targets is still a great challenge. The motion of organs situated in the thorax and abdomen strongly affects the precision of proton and carbon ion radiotherapy. The motion is responsible for not only the dislocation of the tumour but also the alterations in the internal density along the beam path, which influence the range of particle beams. Furthermore, in case of pencil beam scanning, there is an interference between the target movement and dynamic beam delivery. This review presents the strategies for tumour motion monitoring and moving target irradiation in the context of hadron therapy. Methods enabling the direct determination of tumour position (fluoroscopic imaging of implanted radio-opaque fiducial markers, electromagnetic detection of inserted transponders and ultrasonic tumour localization systems) are presented. Attention is also drawn to the techniques which use external surrogate motion for an indirect estimation of target displacement during irradiation. The role of respiratory-correlated CT [four-dimensional CT (4DCT)] in the determination of motion pattern prior to the particle treatment is also considered. An essential part of the article is the review of the main approaches to moving target irradiation in hadron therapy: gating, rescanning (repainting), gated rescanning and tumour tracking. The advantages, drawbacks and development trends of these methods are discussed. The new accelerators, called "cyclinacs", are presented, because their application to particle therapy will allow making a breakthrough in the 4D spot scanning treatment of moving organs.

  17. Materials characterization of irradiated spectralon from the NIF target chamber

    Science.gov (United States)

    Chow, Robert; Frieders, Gene; Jensen, Wayne; Pearson, Mark; Datte, Phil

    2015-08-01

    The Near Backscatter Imager (NBI) participates in nearly every kind of experiment conducted at NIF and measures backscatter, the result of the interaction between incident laser light and plasma waves at a target. Large Spectralon plates, on the order of a hundreds of mm per side, are used as Lambertian scatter components for the NBI diagnostics. The plates were deployed in 2009 and replaced in April of 2014. All NBI assemblies suffered reflectivity degradation, and some of these changes were spatially localized defects observed after irradiation to a cumulative combined neutron and Υ dose of 0.038 Gy. The growth of a defect was correlated to the combined cumulative neutron and Υ radiation dose from NIF fusion shots. Spectralon plates that were irradiated to cumulative combined neutron and Υ dose of 0.74 Gy were characterized for materials and mechanical changes with the following techniques: RBS, FTIR, XPS, SEM, EDX and tensile tests. These tests indicate that the bulk Spectralon did not measurably degrade but there are discolorations that affect the reflectivity. Surface analysis indicates that the surface CF2 species re-forms to make various organic and CFx species.

  18. Water erosion tests on a tantalum sample: A short communication

    Science.gov (United States)

    Caretta, O.; Davenne, T.; Densham, C. J.

    2017-08-01

    This paper reports results from an experiment exposing the hot isostatic pressed tantalum cladding of a tungsten spallation target sample to a 34 m/s water jet. The unpolished tantalum surface was placed under the jet for 4.5 months with a view to quantifying pitting and erosion. Micrographs and laser profilometry records of the sample surface taken before and after the experiment are reported here.

  19. Physics of Double Pulse Irradiation of Targets For Proton Acceleration

    Science.gov (United States)

    Kerr, S.; Mo, M.; Masud, R.; Manzoor, L.; Tiedje, H.; Tsui, Y.; Fedosejevs, R.; Link, A.; Patel, P.; McLean, H.; Hazi, A.; Chen, H.; Ceurvorst, L.; Norreys, P.

    2016-10-01

    Experiments have been carried out on double-pulse irradiation of um-scale foil targets with varying preplasma conditions. Our experiment at the Titan Laser facility utilized two 700 fs, 1054 nm pulses, separated by 1 to 5 ps with a total energy of 100 J, and with 5-20% of the total energy contained within the first pulse. The proton spectra were measured with radiochromic film stacks and magnetic spectrometers. The prepulse energy was on the order of 10 mJ, which appears to have a moderating effect on the double pulse enhancement of proton beam. We have performed LSP PIC simulations to understand the double pulse enhancement mechanism, as well as the role of preplasma in modifying the interaction. A 1D parameter study was done to isolate various aspects of the interaction, while 2D simulations provide more detailed physical insight and a better comparison with experimental data. Work by the Univ. of Alberta was supported by the Natural Sciences and Engineering Research Council of Canada. Work by LLNL was performed under the auspices of U.S. DOE under contract DE-AC52-07NA27344.

  20. Contact Resistance of Tantalum Coatings in Fuel Cells and Electrolyzers using Acidic Electrolytes at Elevated Temperatures

    DEFF Research Database (Denmark)

    Jensen, Annemette Hindhede; Christensen, Erik; Barner, Jens H. Von

    2014-01-01

    Tantalum has so far been found to be the only construction material with sufficient corrosion resistance for high temperature polymer electrolyte membrane electrolyzers using acidic electrolytes above 100◦C. In this work the interfacial contact resistances of tantalum plates and tantalum coated...... stainless steel were found to be far below the US Department of Energy target value of 10mcm2. The good contact resistance of tantalum was demonstrated by simulating high temperature polymer electrolyte membrane electrolysis conditions by anodization performed in 85% phosphoric acid at 130◦C, followed...

  1. Investigation of heat release in the targets during irradiation by ion beams

    CERN Document Server

    Dalkarov, O D; Rusetskii, A S

    2015-01-01

    The DD-reaction is investigated and the heat emission off the targets during their irradiation with ion beams is studied at the HELIS ion accelerator at LPI. The heat emission is observed to be significantly higher in the case of irradiation of the Ti/TiO2:Dx-targets by a D+ beam, as compared to the H+ and Ne+ beams. Furthermore, it depends on the concentration of deuterium in the target and current density of the deuteron beam.

  2. Direct detection of delayed high energy electrons from the 181Ta target irradiated by a moderate intensity femtosecond laser pulse

    Science.gov (United States)

    Savel’ev, A.; Chefonov, O.; Ovchinnikov, A.; Agranat, M.; Spohr, K. M.

    2017-03-01

    We depict an experimental study of delayed fast, negatively charged particles from femtosecond laser-plasma interaction at an intensity of I ∼ 1017 W cm‑2. Plates of 2 mm thickness made of 181Ta (∼100% abundance) and natural W were used as targets. We distinguished certain delayed events due to detection of negative H‑, C‑ and O‑ ions. However, most events which were delayed by 0.5–5 μs with respect to the instantaneous plasma formation caused by the laser pulses, were identified as electrons with energies of 3–7 keV. A comparative analysis between the tantalum and tungsten spectra was undertaken. This revealed a close similarity between the measured spectrum for tantalum and the predicted spectrum for electrons arising from to the internal conversion decay of the 6.237 keV nuclear isomeric state in 181Ta.

  3. Spallation modeling in tantalum

    Energy Technology Data Exchange (ETDEWEB)

    Tonks, D.L.; Hixson, R.; Zurek, A.K.; Thissell, W.

    1997-09-01

    A gas gun plate impact spallation experiment has been performed on commercial purity rolled tantalum. The shock pressure achieved was about 7 Gpa and was sufficient to induce incipient spallation. The particle velocity was measured at the free surface of the spalled plate, and the spalled sample was recovered and examined metallographically using image analysis. The quantitative image analysis results are being used to develop a damage model. The model is micromechanically based and involves novel void growth and coalescence processes. The 1D characteristics code CHARADE has been used in a preliminary simulation of the VISAR free surface particle velocity record. Implications for ductile damage modeling will be discussed.

  4. Determination of the accuracy for targeted irradiations of cellular substructures at SNAKE

    Energy Technology Data Exchange (ETDEWEB)

    Siebenwirth, C. [Department of Radiation Oncology, Klinikum rechts der Isar, Technische Universität München, Munich (Germany); Institut für Angewandte Physik und Messtechnik (LRT2), Universität der Bundeswehr München, Neubiberg (Germany); Greubel, C. [Institut für Angewandte Physik und Messtechnik (LRT2), Universität der Bundeswehr München, Neubiberg (Germany); Drexler, S.E. [Department of Radiation Oncology, Ludwig-Maximilians-Universität München, Munich (Germany); Girst, S.; Reindl, J. [Institut für Angewandte Physik und Messtechnik (LRT2), Universität der Bundeswehr München, Neubiberg (Germany); Walsh, D.W.M. [Institut für Angewandte Physik und Messtechnik (LRT2), Universität der Bundeswehr München, Neubiberg (Germany); Department of Radiation Oncology, Klinikum rechts der Isar, Technische Universität München, Munich (Germany); Dollinger, G. [Institut für Angewandte Physik und Messtechnik (LRT2), Universität der Bundeswehr München, Neubiberg (Germany); Friedl, A.A. [Department of Radiation Oncology, Ludwig-Maximilians-Universität München, Munich (Germany); and others

    2015-04-01

    In the last 10 years the ion microbeam SNAKE, installed at the Munich 14 MV tandem accelerator, has been successfully used for radiobiological experiments by utilizing pattern irradiation without targeting single cells. Now for targeted irradiation of cellular substructures a precise irradiation device was added to the live cell irradiation setup at SNAKE. It combines a sub-micrometer single ion irradiation facility with a high resolution optical fluorescence microscope. Most systematic errors can be reduced or avoided by using the same light path in the microscope for beam spot verification as well as for and target recognition. In addition online observation of the induced cellular responses is possible. The optical microscope and the beam delivering system are controlled by an in-house developed software which integrates the open-source image analysis software, CellProfiler, for semi-automatic target recognition. In this work the targeting accuracy was determined by irradiation of a cross pattern with 55 MeV carbon ions on nucleoli in U2OS and HeLa cells stably expressing a GFP-tagged repair protein MDC1. For target recognition, nuclei were stained with Draq5 and nucleoli were stained with Syto80 or Syto83. The damage response was determined by live-cell imaging of MDC1-GFP accumulation directly after irradiation. No systematic displacement and a random distribution of about 0.7 μm (SD) in x-direction and 0.8 μm (SD) in y-direction were observed. An independent analysis after immunofluorescence staining of the DNA damage marker yH2AX yielded similar results. With this performance a target with a size similar to that of nucleoli (i.e. a diameter of about 3 μm) is hit with a probability of more than 80%, which enables the investigation of the radiation response of cellular subcompartments after targeted ion irradiation in the future.

  5. Laser-induced breakdown spectroscopy of tantalum plasma

    Energy Technology Data Exchange (ETDEWEB)

    Khan, Sidra; Bashir, Shazia; Hayat, Asma; Khaleeq-ur-Rahman, M.; Faizan–ul-Haq [Centre for Advanced Studies in Physics, GC University, Lahore (Pakistan)

    2013-07-15

    Laser Induced Breakdown spectroscopy (LIBS) of Tantalum (Ta) plasma has been investigated. For this purpose Q-switched Nd: YAG laser pulses (λ∼ 1064 nm, τ∼ 10 ns) of maximum pulse energy of 100 mJ have been employed as an ablation source. Ta targets were exposed under the ambient environment of various gases of Ar, mixture (CO{sub 2}: N{sub 2}: He), O{sub 2}, N{sub 2}, and He under various filling pressure. The emission spectrum of Ta is observed by using LIBS spectrometer. The emission intensity, excitation temperature, and electron number density of Ta plasma have been evaluated as a function of pressure for various gases. Our experimental results reveal that the optical emission intensity, the electron temperature and density are strongly dependent upon the nature and pressure of ambient environment. The SEM analysis of the ablated Ta target has also been carried out to explore the effect of ambient environment on the laser induced grown structures. The growth of grain like structures in case of molecular gases and cone-formation in case of inert gases is observed. The evaluated plasma parameters by LIBS analysis such as electron temperature and the electron density are well correlated with the surface modification of laser irradiated Ta revealed by SEM analysis.

  6. Heavy-Ion Irradiation of Thulium(III) Oxide Targets Prepared by Polymer-Assisted Deposition

    Energy Technology Data Exchange (ETDEWEB)

    Garcia, Mitch A.; Ali, Mazhar N.; Chang, Noel N.; Parsons-Moss, Tashi; Ashby, Paul D.; Gates, Jacklyn M.; Stavsetra, Liv; Gregorich, Kenneth E.; Nitsche, Heino

    2008-09-15

    Thulium(III) oxide (Tm{sub 2}O{sub 3}) targets prepared by the polymer-assisted deposition (PAD) method were irradiated by heavy-ion beams to test the method's feasibility for nuclear science applications. Targets were prepared on silicon nitride backings (thickness of 1000 nm, 344 {micro}g/cm{sup 2}) and were irradiated with an {sup 40}Ar beam at laboratory frame energy of {approx}210 MeV (50 particle nA). The root mean squared (RMS) roughness prior to irradiation is 1.1 nm for a {approx}250 nm ({approx}220 {micro}g/cm{sup 2}) Tm{sub 2}O{sub 3} target, and an RMS roughness of 2.0 nm after irradiation was measured by atomic force microscopy (AFM). Scanning electron microscopy of the irradiated target reveals no significant differences in surface homogeneity when compared to imaging prior to irradiation. Target flaking was not observed from monitoring Rutherford scattered particles as a function of time.

  7. Platelet-containing tantalum powders

    Energy Technology Data Exchange (ETDEWEB)

    Schiele, E.K.

    1988-04-26

    A method of forming platelet tantalum powders is described comprising the steps of: (a) providing an ingot-derived precursor tantalum powder, and (b) ball-milling the precursor powder for a time sufficient to form a platelet powder having an average FSSS of less than about 2 micrometers, a Scott density not greater than about 30 g/in/sup 3/ and a BET surface area of at least about 0.7 in/sup 2//g.

  8. Compton profile of tantalum

    Indian Academy of Sciences (India)

    Thomas Varghese; K M Balakrishna; K Siddappa

    2003-03-01

    The Compton profile of tantalum (Ta) has been measured using IGP type coaxial photon detector. The target atoms were excited by means of 59.54 keV -rays from Am-241. The measurements were carried out on a high purity thin elemental foil. The data were recoreded in a 4 K multichannel analyzer. These data duly corrected for various effects are presented and compared with theoretical and measured values. Best agreement with experiment is found for the 5d36s2 electron configuration.

  9. Hydride Olefin complexes of tantalum and niobium

    NARCIS (Netherlands)

    Klazinga, Aan Hendrik

    1979-01-01

    This thesis describes investigations on low-valent tantalum and niobium hydride and alkyl complexes, particularly the dicyclopentadienyl tantalum hydride olefin complexes Cp2Ta(H)L (L=olefin). ... Zie: Summary

  10. Synthesis and characterization of tantalum silsesquioxane complexes.

    Science.gov (United States)

    Guillo, Pascal; Fasulo, Meg E; Lipschutz, Michael I; Tilley, T Don

    2013-02-14

    Tantalum polyhedral oligosilsesquioxane (POSS) complexes have been synthesised and characterized. X-ray structures of these complexes revealed that the coordination number of the tantalum center greatly affects the cube-like silsesquioxane framework.

  11. Shock dynamics induced by double-spot laser irradiation of layered targets

    Directory of Open Access Journals (Sweden)

    Aliverdiev Abutrab A.

    2015-06-01

    Full Text Available We studied the interaction of a double-spot laser beam with targets using the Prague Asterix Laser System (PALS iodine laser working at 0.44 μm wavelength and intensity of about 1015 W/cm2. Shock breakout signals were recorder using time-resolved self-emission from target rear side of irradiated targets. We compared the behavior of pure Al targets and of targets with a foam layer on the laser side. Results have been simulated using hydrodynamic numerical codes.

  12. Systems and methods for processing irradiation targets through a nuclear reactor

    Science.gov (United States)

    Dayal, Yogeshwar; Saito, Earl F.; Berger, John F.; Brittingham, Martin W.; Morales, Stephen K.; Hare, Jeffrey M.

    2016-05-03

    Apparatuses and methods produce radioisotopes in instrumentation tubes of operating commercial nuclear reactors. Irradiation targets may be inserted and removed from instrumentation tubes during operation and converted to radioisotopes otherwise unavailable during operation of commercial nuclear reactors. Example apparatuses may continuously insert, remove, and store irradiation targets to be converted to useable radioisotopes or other desired materials at several different origin and termination points accessible outside an access barrier such as a containment building, drywell wall, or other access restriction preventing access to instrumentation tubes during operation of the nuclear plant.

  13. Vacuum heating of solid target irradiated by femtosecond laser pulses

    Institute of Scientific and Technical Information of China (English)

    DONG; Quanli(董全力); ZHANG; Jie(张杰)

    2003-01-01

    The interaction of femtosecond laser pulses with solid targets was studied through experiments and particle-in-cell (PIC) simulations. It is proved that the vacuum heating and the inverse bremsstralung process are the main mechanisms of the laser pulse absorption under such conditions. The distribution of hot electrons and that of X-ray are found to have double-temperature structure, which is confirmed by PIC simulations. While the lower temperature is attributed to the resonant absorption, the higher one, however, is caused by the laser-induced electric field in the target normal direction. The time-integrated spectra ofthe reflected laser pulse shows that the mechanism of electron acceleration is determined by the plasma density profile.

  14. Separation of Plutonium from Irradiated Fuels and Targets

    Energy Technology Data Exchange (ETDEWEB)

    Gray, Leonard W. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Holliday, Kiel S. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Murray, Alice [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Thompson, Major [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Thorp, Donald T. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Yarbro, Stephen [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Venetz, Theodore J. [Hanford Site, Benton County, WA (United States)

    2015-09-30

    Spent nuclear fuel from power production reactors contains moderate amounts of transuranium (TRU) actinides and fission products in addition to the still slightly enriched uranium. Originally, nuclear technology was developed to chemically separate and recover fissionable plutonium from irradiated nuclear fuel for military purposes. Military plutonium separations had essentially ceased by the mid-1990s. Reprocessing, however, can serve multiple purposes, and the relative importance has changed over time. In the 1960’s the vision of the introduction of plutonium-fueled fast-neutron breeder reactors drove the civilian separation of plutonium. More recently, reprocessing has been regarded as a means to facilitate the disposal of high-level nuclear waste, and thus requires development of radically different technical approaches. In the last decade or so, the principal reason for reprocessing has shifted to spent power reactor fuel being reprocessed (1) so that unused uranium and plutonium being recycled reduce the volume, gaining some 25% to 30% more energy from the original uranium in the process and thus contributing to energy security and (2) to reduce the volume and radioactivity of the waste by recovering all long-lived actinides and fission products followed by recycling them in fast reactors where they are transmuted to short-lived fission products; this reduces the volume to about 20%, reduces the long-term radioactivity level in the high-level waste, and complicates the possibility of the plutonium being diverted from civil use – thereby increasing the proliferation resistance of the fuel cycle. In general, reprocessing schemes can be divided into two large categories: aqueous/hydrometallurgical systems, and pyrochemical/pyrometallurgical systems. Worldwide processing schemes are dominated by the aqueous (hydrometallurgical) systems. This document provides a historical review of both categories of reprocessing.

  15. Lithium target for accelerator based BNCT neutron source: Influence by the proton irradiation on lithium

    Science.gov (United States)

    Fujii, R.; Imahori, Y.; Nakakmura, M.; Takada, M.; Kamada, S.; Hamano, T.; Hoshi, M.; Sato, H.; Itami, J.; Abe, Y.; Fuse, M.

    2012-12-01

    The neutron source for Boron Neutron Capture Therapy (BNCT) is in the transition stage from nuclear reactor to accelerator based neutron source. Generation of low energy neutron can be achieved by 7Li (p, n) 7Be reaction using accelerator based neutron source. Development of small-scale and safe neutron source is within reach. The melting point of lithium that is used for the target is low, and durability is questioned for an extended use at a high current proton beam. In order to test its durability, we have irradiated lithium with proton beam at the same level as the actual current density, and found no deterioration after 3 hours of continuous irradiation. As a result, it is suggested that lithium target can withstand proton irradiation at high current, confirming suitability as accelerator based neutron source for BNCT.

  16. Flake tantalum powder for manufacturing electrolytic capacitors

    Institute of Scientific and Technical Information of China (English)

    HE Jilin; YANG Guoqi; PAN Luntao; LIU Hongdong; BAO Xifang

    2008-01-01

    The FTP200 flake tantalum powder was introduced.The microstructures of the powder with leaf-like primary particles having an average flakiness of 2 to 20 and porous agglomerated particles were observed.The chemical composition,physical properties,and electrical properties of the FTP200 powder were compared with those of the FTW300 nodular powder.The FTP200 powder is more sinter-resistant,and the surface area of the flake tantalum powder under sintering at high temperature has less loss than that of the nodular tantalum powder.The specific capacitance of the flake tantalum powder is higher than that of the nodular tantalum powder with the same surface area when anodized at high voltage,Thus,the flake tantalum powder is suitable for manufacturing tantalum solid electrolytic capacitors in the range of median and high (20-63 V) voltages.

  17. Validation of a new design of tellurium dioide-irradiated target

    Energy Technology Data Exchange (ETDEWEB)

    Fllaoui, Aziz; Ghamad, Younes; Zoubir, Brahim; Ayaz, Zinel Abidine; El Morabiti, Aissam; Amayoud, Hafid [Centre National de l' Energie des Sciences et des Techniques Nucleaires, Rabat (Morocco); Chakir, El Mahjoub [Nuclear Physics Department, University Ibn Toufail, Kenitra (Morocco)

    2016-10-15

    Production of iodine-131 by neutron activation of tellurium in tellurium dioxide (TeO{sub 2}) material requires a target that meets the safety requirements. In a radiopharmaceutical production unit, a new lid for a can was designed, which permits tight sealing of the target by using tungsten inert gas welding. The leakage rate of all prepared targets was assessed using a helium mass spectrometer. The accepted leakage rate is ≤ 10 - 4 mbr.L/s, according to the approved safety report related to iodine-131 production in the TRIGA Mark II research reactor (TRIGA: Training, Research, Isotopes, General Atomics). To confirm the resistance of the new design to the irradiation conditions in the TRIGA Mark II research reactor's central thimble, a study of heat effect on the sealed targets for 7 hours in an oven was conducted and the leakage rates were evaluated. The results show that the tightness of the targets is ensured up to 600 .deg. C with the appearance of deformations on lids beyond 450 .deg. C. The study of heat transfer through the target was conducted by adopting a one-dimensional approximation, under consideration of the three transfer modes-convection, conduction, and radiation. The quantities of heat generated by gamma and neutron heating were calculated by a validated computational model for the neutronic simulation of the TRIGA Mark II research reactor using the Monte Carlo N-Particle transport code. Using the heat transfer equations according to the three modes of heat transfer, the thermal study of I-131 production by irradiation of the target in the central thimble showed that the temperatures of materials do not exceed the corresponding melting points. To validate this new design, several targets have been irradiated in the central thimble according to a preplanned irradiation program, going from 4 hours of irradiation at a power level of 0.5 MW up to 35 hours (7 h/d for 5 days a week) at 1.5 MW. The results show that the irradiated targets are

  18. Validation of a New Design of Tellurium Dioxide-Irradiated Target

    Directory of Open Access Journals (Sweden)

    Aziz Fllaoui

    2016-10-01

    Full Text Available Production of iodine-131 by neutron activation of tellurium in tellurium dioxide (TeO2 material requires a target that meets the safety requirements. In a radiopharmaceutical production unit, a new lid for a can was designed, which permits tight sealing of the target by using tungsten inert gas welding. The leakage rate of all prepared targets was assessed using a helium mass spectrometer. The accepted leakage rate is ≤ 10−4 mbr.L/s, according to the approved safety report related to iodine-131 production in the TRIGA Mark II research reactor (TRIGA: Training, Research, Isotopes, General Atomics. To confirm the resistance of the new design to the irradiation conditions in the TRIGA Mark II research reactor's central thimble, a study of heat effect on the sealed targets for 7 hours in an oven was conducted and the leakage rates were evaluated. The results show that the tightness of the targets is ensured up to 600°C with the appearance of deformations on lids beyond 450°C. The study of heat transfer through the target was conducted by adopting a one-dimensional approximation, under consideration of the three transfer modes—convection, conduction, and radiation. The quantities of heat generated by gamma and neutron heating were calculated by a validated computational model for the neutronic simulation of the TRIGA Mark II research reactor using the Monte Carlo N-Particle transport code. Using the heat transfer equations according to the three modes of heat transfer, the thermal study of I-131 production by irradiation of the target in the central thimble showed that the temperatures of materials do not exceed the corresponding melting points. To validate this new design, several targets have been irradiated in the central thimble according to a preplanned irradiation program, going from 4 hours of irradiation at a power level of 0.5 MW up to 35 hours (7 h/d for 5 days a week at 1.5 MW. The results show that the irradiated targets are

  19. Characterization of advanced polymethylmethacrylate (PMMA) targets for TNSA laser irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Torrisi, L., E-mail: Lorenzo.Torrisi@unime.it [Department of Physics and Earth Science, Messina University, V.le F.S. d’Alcontres 31, 98166 S. Agata, Messina (Italy); Cutroneo, M.; Semian, V. [Nuclear Physics Institute, ASCR, 250 68 Rez (Czech Republic); Ceccio, G. [Department of Physics and Earth Science, Messina University, V.le F.S. d’Alcontres 31, 98166 S. Agata, Messina (Italy)

    2015-10-01

    Highlights: • The manuscript presents the procedure to prepare thin advanced targets based on PMMA polymer in order to obtain high ion acceleration in laser-generated plasma. • The manuscript is original for the procedures of polymer preparation and preliminary techniques used. - Abstract: Characterization of advanced micrometric foils suitable for TNSA regime were performed using optical spectroscopy, microscopy and Nd:YAG low laser intensity. Micrometric acrylic beads were produced in polymethylmethacrylate foils through complex physical and technical procedures in order to enhance the absorption coefficient in the IR region. Moreover, Au nanoparticles were embedded in the polymer in order to induce surface plasmon resonance absorption and plasma electron density enhancement. The suitably prepared polymers were investigated at low laser intensity to have evidence of their capability to absorb IR wavelength radiations and promote enhancement of the plasma temperature and density. Results indicate that the high transparence of PMMA foils can be strongly reduced by the presences of the micrometric acrylic beads and that the obtainable laser-generated plasma improves the ion acceleration when high beads density and high Au nanoparticles concentrations are employed.

  20. Post Irradiation Examination Results of the NT-02 Graphite Fins NUMI Target

    Energy Technology Data Exchange (ETDEWEB)

    Ammigan, K. [Fermilab; Hurh, P. [Fermilab; Sidorov, V. [Fermilab; Zwaska, R. [Fermilab; Asner, D. M. [PNL, Richland; Casella, Casella,A.M [PNL, Richland; Edwards, D. J. [PNL, Richland; Schemer-Kohrn, A. L. [PNL, Richland; Senor, D. J. [PNL, Richland

    2017-02-10

    The NT-02 neutrino target in the NuMI beamline at Fermilab is a 95 cm long target made up of segmented graphite fins. It is the longest running NuMI target, which operated with a 120 GeV proton beam with maximum power of 340 kW, and saw an integrated total proton on target of 6.1 1020. Over the last half of its life, gradual degradation of neutrino yield was observed until the target was replaced. The probable causes for the target performance degradation are attributed to radiation damage, possibly including cracking caused by reduction in thermal shock resistance, as well as potential localized oxidation in the heated region of the target. Understanding the long-termstructural response of target materials exposed to proton irradiation is critical as future proton accelerator sources are becoming increasingly more powerful. As a result, an autopsy of the target was carried out to facilitate post-irradiation examination of selected graphite fins. Advanced microstructural imaging and surface elemental analysis techniques were used to characterize the condition of the fins in an effort to identify degradation mechanisms, and the relevant findings are presented in this paper.

  1. Niobium and tantalum: indispensable twins

    Science.gov (United States)

    Schulz, Klaus; Papp, John

    2014-01-01

    Niobium and tantalum are transition metals almost always paired together in nature. These “twins” are difficult to separate because of their shared physical and chemical properties. In 1801, English chemist Charles Hatchett uncovered an unknown element in a mineral sample of columbite; John Winthrop found the sample in a Massachusetts mine and sent it to the British Museum in London in 1734. The name columbium, which Hatchet named the new element, came from the poetic name for North America—Columbia—and was used interchangeably for niobium until 1949, when the name niobium became official. Swedish scientist Anders Ekberg discovered tantalum in 1802, but it was confused with niobium, because of their twinned properties, until 1864, when it was recognized as a separate element. Niobium is a lustrous, gray, ductile metal with a high melting point, relatively low density, and superconductor properties. Tantalum is a dark blue-gray, dense, ductile, very hard, and easily fabricated metal. It is highly conductive to heat and electricity and renowned for its resistance to acidic corrosion. These special properties determine their primary uses and make niobium and tantalum indispensable.

  2. Additively manufactured porous tantalum implants

    NARCIS (Netherlands)

    Wauthle, Ruben; Van Der Stok, Johan; Yavari, Saber Amin; Van Humbeeck, Jan; Kruth, Jean Pierre; Zadpoor, Amir Abbas; Weinans, Harrie; Mulier, Michiel; Schrooten, Jan

    2015-01-01

    The medical device industry's interest in open porous, metallic biomaterials has increased in response to additive manufacturing techniques enabling the production of complex shapes that cannot be produced with conventional techniques. Tantalum is an important metal for medical devices because of it

  3. Proton driven acceleration by intense laser pulses irradiating thin hydrogenated targets

    Science.gov (United States)

    Torrisi, L.; Cutroneo, M.; Cavallaro, S.; Giuffrida, L.; Andò, L.; Cirrone, P.; Bertuccio, G.; Puglisi, D.; Calcagno, L.; Verona, C.; Picciotto, A.; Krasa, J.; Margarone, D.; Velyhan, A.; Laska, L.; Krousky, E.; Pfeiffer, M.; Skala, J.; Ullschmied, J.; Wolowski, J.; Badziak, J.; Rosinski, M.; Ryc, L.; Szydlowski, A.

    2013-05-01

    The Asterix iodine laser of the PALS laboratory in Prague, operating at 1315 nm fundamental frequency, 300 ps pulse duration, 600 J maximum pulse energy and 1016 W/cm2 intensity, is employed to irradiate thin hydrogenated targets placed in high vacuum. Different metallic and polymeric targets allow to generate multi-energetic and multi-specie ion beams showing peculiar properties. The plasma obtained by the laser irradiation is monitored, in terms of properties of the emitted charge particles, by using time-of-flight techniques and Thomson parabola spectrometer (TPS). A particular attention is given to the proton beam production in terms of the maximum energy, emission yield and angular distribution as a function of the laser energy, focal position (FP), target thickness and composition.

  4. Investigation on Soft X-Ray Lasers with a Picosecond-Laser-Irradiated Gas Puff Target

    Energy Technology Data Exchange (ETDEWEB)

    Fiedorowiez, H; Bartnik, A; Jarocki, R; Rakowski, R; Dunn, J; Smith, R F; Hunter, J; Hilsen, J; Shlyaptsev, V N

    2002-10-09

    We present results of experimental studies on transient gain soft x-ray lasers with a picosecond-laser-irradiated gas puff target. The target in a form of an elongated gas sheet is formed by pulsed injection of gas through a slit nozzle using a high-pressure electromagnetic valve developed and characterized at the Institute of Optoelectronics. The x-ray laser experiments were performed at the Lawrence Livermore National Laboratory using the tabletop Compact Multipulse Terawatt (COMET) laser to irradiate argon, krypton or xenon gas puff targets. Soft x-ray lasing in neon-like argon on the 3p-3s transition at 46.9 nm and the 3d-3p transition at 45.1 nm have been demonstrated, however, no amplification for nickel-like krypton or xenon was observed. Results of the experiments are presented and discussed.

  5. Post-Irradiation Examination of 237Np Targets for 238Pu Production

    Energy Technology Data Exchange (ETDEWEB)

    Morris, Robert Noel [ORNL; Baldwin, Charles A [ORNL; Hobbs, Randy W [ORNL; Schmidlin, Joshua E [ORNL

    2015-01-01

    Oak Ridge National Laboratory is recovering the US 238Pu production capability and the first step in the process has been to evaluate the performance of a 237Np target cermet pellet encased in an aluminum clad. The process proceeded in 3 steps; the first step was to irradiate capsules of single pellets composed of NpO2 and aluminum power to examine their shrinkage and gas release. These pellets were formed by compressing sintered NpO2 and aluminum powder in a die at high pressure followed by sintering in a vacuum furnace. Three temperatures were chosen for sintering the solution precipitated NpO2 power used for pellet fabrication. The second step was to irradiate partial targets composed of 8 pellets in a semi-prototypical arrangement at the two best performing sintering temperatures to determine which temperature gave a pellet that performed the best under the actual planned irradiation conditions. The third step was to irradiate ~50 pellets in an actual target configuration at design irradiation conditions to assess pellet shrinkage and gas release, target heat transfer, and dimensional stability. The higher sintering temperature appeared to offer the best performance after one cycle of irradiation by having the least shrinkage, thus keeping the heat transfer gap between the pellets and clad small minimizing the pellet operating temperature. The final result of the testing was a target that can meet the initial production goals, satisfy the reactor safety requirements, and can be fabricated in production quantities. The current focus of the program is to verify that the target can be remotely dissembled, the pellets dissolved, and the 238Pu recovered. Tests are being conducted to examine these concerns and to compare results to code predictions. Once the performance of the full length targets has been quantified, the pellet 237Np loading will be revisited to determine if it can be

  6. Blood vessel damage correlated with irradiance for in vivo vascular targeted photodynamic therapy

    Science.gov (United States)

    Zhang, Jinde; Tan, Zou; Niu, Xiangyu; Lin, Linsheng; Lin, Huiyun; Li, Buhong

    2016-10-01

    Vascular targeted photodynamic therapy (V-PDT) has been widely utilized for the prevention or treatment of vascular-related diseases, including age-related macular degeneration, port-wine stains and prostate cancer. In order to quantitative assessment the blood vessel damage during V-PDT, nude mice were implanted with Titanium dorsal skin window chambers for in vivo V-PDT studies. For treatments, various irradiances including 50, 75, 100 and 200 mW/cm2 provided by a 532 nm semiconductor laser were performed with the same total light dose of 30 J/cm2 after the mice were intravenously injection of Rose Bengal for 25 mg/Kg body weight. Laser speckle imaging and microscope were used to monitor blood flow dynamics and vessel constriction during and after V-PDT, respectively. The V-PDT induced vessel damages between different groups were compared. The results show that significant difference in blood vessel damage was found between the lower irradiances (50, 75 and 100 mW/cm2) and higher irradiance (200 mW/cm2), and the blood vessel damage induced by V-PDT is positively correlated with irradiance. This study implies that the optimization of irradiance is required for enhancing V-PDT therapeutic efficiency.

  7. The development of uranium foil farication technology utilizing twin roll method for Mo-99 irradiation target

    CERN Document Server

    Kim, C K; Park, H D

    2002-01-01

    MDS Nordion in Canada, occupying about 75% of global supply of Mo-99 isotope, has provided the irradiation target of Mo-99 using the rod-type UAl sub x alloys with HEU(High Enrichment Uranium). ANL (Argonne National Laboratory) through co-operation with BATAN in Indonesia, leading RERTR (Reduced Enrichment for Research and Test Reactors) program substantially for nuclear non-proliferation, has designed and fabricated the annular cylinder of uranium targets, and successfully performed irradiation test, in order to develop the fabrication technology of fission Mo-99 using LEU(Low Enrichment Uranium). As the uranium foils could be fabricated in laboratory scale, not in commercialized scale by hot rolling method due to significant problems in foil quality, productivity and economic efficiency, attention has shifted to the development of new technology. Under these circumstances, the invention of uranium foil fabrication technology utilizing twin-roll casting method in KAERI is found to be able to fabricate LEU or...

  8. Characterization of Tantalum Polymer Capacitors

    Science.gov (United States)

    Spence, Penelope

    2012-01-01

    Overview Reviewed data Caution must be taken when accelerating test conditions Data not useful to establish an acceleration model Introduction of new failure mechanism skewing results Evidence of Anti-Wear-Out De-doping of polymer Decreased capacitance Increased ESR Not dielectric breakdown Needs further investigation Further investigation into tantalum polymer capacitor technology Promising acceleration model for Manufacturer A Possibility for use in high-reliability space applications with suitable voltage derating.

  9. Thin-film preparation by back-surface irradiation pulsed laser deposition using metal powder targets

    Science.gov (United States)

    Kawasaki, Hiroharu; Ohshima, Tamiko; Yagyu, Yoshihito; Ihara, Takeshi; Yamauchi, Makiko; Suda, Yoshiaki

    2017-01-01

    Several kinds of functional thin films were deposited using a new thin-film preparation method named the back-surface irradiation pulsed laser deposition (BIPLD) method. In this BIPLD method, powder targets were used as the film source placed on a transparent target holder, and then a visible-wavelength pulsed laser was irradiated from the holder side to the substrate. Using this new method, titanium oxide and boron nitride thin films were deposited on the silicon substrate. Surface scanning electron microscopy (SEM) images suggest that all of the thin films were deposited on the substrate with some large droplets irrespective of the kind of target used. The deposition rate of the films prepared by using this method was calculated from film thickness and deposition time to be much lower than that of the films prepared by conventional PLD. X-ray diffraction (XRD) measurement results suggest that rutile and anatase TiO2 crystal peaks were formed for the films prepared using the TiO2 rutile powder target. Crystal peaks of hexagonal boron nitride were observed for the films prepared using the boron nitride powder target. The crystallinity of the prepared films was changed by annealing after deposition.

  10. Remotely Operated Equipment for Post Irradiation Examination of the SNS Target Vessel

    Energy Technology Data Exchange (ETDEWEB)

    Carroll, Adam J [ORNL; Graves, Van B [ORNL; Dayton, Michael J [ORNL; Riemer, Bernie [ORNL

    2011-01-01

    The Spallation Neutron Source produces neutrons by accelerating protons into flowing mercury contained inside a stainless steel target vessel. During facility operation the target vessel is degraded by a combination of high-energy neutrons, the proton beam, and cavitation-induced corrosion. The degradation is primarily concentrated at the nose of the target vessel, where the proton beam passes through. Currently, the Spallation Neutron Source has replaced three target vessels and is operating the fourth. To minimize the operational costs of manufacturing and disposing of target vessels, efforts are underway to increase the operational lifetimes of the target vessels by conducting post irradiation examinations of spent vessels. This examination involves remotely removing multiple coupons from the nose of the target vessel using a single piece of equipment, called the Nose Sampling Cutter, installed inside the Spallation Neutron Source s hot cell. The Cutter produces circular coupons approximately 2 inches in diameter using a carbide-tipped hole saw. The nose of the target vessel consists of four layers of material, and the Nose Sampling Cutter is capable of cutting through the layers in a single stroke. This remote operation has been successfully completed twice. In addition to the Nose Sampling Cutter, a large reciprocation saw capable of removing a sizable section of the nose of the target vessel has been constructed and tested, but never implemented. To support this large reciprocation saw other equipment has also been designed. The details of the Nose Sampling Cutter, reciprocation saw, and associated equipment are discussed.

  11. Numerical study of the irradiation uniformity of a directly driven inertial confinement fusion target

    Science.gov (United States)

    Temporal, M.; Canaud, B.; Laffite, S.; Le Garrec, B. J.; Murakami, M.

    2010-11-01

    In the Inertial Confinement Fusion the uniformity of the irradiation still represents a crucial issue. In this context a spherical capsule directly driven by laser beams have been assessed numerically [1]. Two schemes characterized by 32 and 48 directions of irradiation [2] with associated a single laser beam or a bundle of laser beams [3] characterized by a super-Gaussian intensity profile are considered. Beam imperfections as power imbalance and pointing errors have been taken into account. It is found that the focal spot that minimizes the rms deviation depends on the beam imperfections [4]. The numerical calculations show that the uniformity of the irradiation evolves in time. The results calculated considering the illumination of a spherical target will be compared with those obtained when the irradiation is taken into account. [1] M. Temporal, B. Canaud. Eur. Phys. J. D 55 139 (2009). [2] M. Murakami, N. Sarukura, H. Azechi, M. Temporal, A.J. Schmitt, in press to Phys. Plasmas (July issue, 2010). [3] M. Temporal, B. Canaud, B. J. Le Garrec, Phys. Plasmas 17 022701 (2010). [4] M. Temporal, B. Canaud, S. Laffite, B.J. Le Garrec, M. Murakami. Phys. Plasmas 17 064504 (2010).

  12. Compaction and sintering of nickel powder used encapsulation of irradiation targets

    Energy Technology Data Exchange (ETDEWEB)

    Miyano, Rosana S.L.; Guimaraes, Raquel R.F.L.; Rossi, Jesualdo L., E-mail: rosatac@gmail.com, E-mail: raquel.lucchesi@icloud.com, E-mail: jelrossi@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (CCTM/IPEN/CNEN-SP), Sao Paulo, SP (Brazil). Centro de Ciencia e Tecnologia de Materiais; Wendhausen, Paulo A.P.; Evangelista, Leandro L., E-mail: paulo.wendhausen@ufsc.br, E-mail: leandro.materiais@gmail.com [Universidade Federal de Santa Catarina (UFSC), Florianopolis, SC (Brazil). Laboratorio de Materiais

    2015-07-01

    The objective of this study was to develop an alternative way to produce targets for irradiation containing uranium, for the pair of {sup 99}Mo production {sup 99m}Tc radionuclide. These targets were obtained by powder metallurgy, the compact serving as means for encapsulation a uranium cylinder to be irradiated. The targets were compacted in an axial hydraulic press applying different pressures up to 800 MPa. The sintering temperature was 600 °C in hydrogen atmosphere and it was used two sintering cycles, one for 4 h and the for 4 h plus 8 h time. The nickel powder was of high purity, that in order to provide the sealing of the fissile content within the compacted. The bulk density of compacted was evaluated by the method geometric. The porosity was measured by mercury porosimetry technique. The microstructure was investigated by optical microscopy. The results obtained with sintering powders involving confirm the feasibility of achieving a casing for uranium targets. (author)

  13. Accumulation of the $^{178m2}Hf$ Isomeric Nuclei Through Spallation with Intermediate-Energy Protons of Tantalum and Rhenium Targets

    CERN Document Server

    Karamian, S A; Adam, J; Filossofov, D V; Henzlova, D; Henzl, V; Kalinnikov, V G; Lebedev, N A; Novgorodov, A F; Collins, C B; Popescu, I I; Ur, C A

    2001-01-01

    The productivity of the spallation reactions at proton energies of 100-660 MeV for accumulation of the radioactive isotopes and isomers has been studied experimentally. Spectra of Ta and Re targets activated at Dubna synchrocyclotron were measured using the methods of radiochemistry and gamma-spectroscopy. Many radioactive products of the spallation and fission reactions are identified, and their yields are compared with the LAHET code simulations. Cross sections, \\sigma_m and isomer-to-ground state ratios, \\sigma_m/\\sigma_g are deduced for nuclear isomers, in particular, for high-spin isomers, as ^{179m2}Hf, ^{179m2}Hf and ^{177m2}Lu. Spin distributions for the spallation-residue nuclei are estimated to understand the \\sigma_m/\\sigma_g ratios. Possibilities to optimize the methods for the long-lived isomers production are discussed, and it would be a necessary step on the way to accumulate such exotic radionuclides in milligram amount under reasonable cost and radiation safety conditions.

  14. Gamma Knife irradiation method based on dosimetric controls to target small areas in rat brains

    Energy Technology Data Exchange (ETDEWEB)

    Constanzo, Julie; Paquette, Benoit; Charest, Gabriel [Center for Radiotherapy Research, Department of Nuclear Medicine and Radiobiology, Université de Sherbrooke, 3001 12th Avenue Nord, Sherbrooke, Québec J1H 5N4 (Canada); Masson-Côté, Laurence; Guillot, Mathieu, E-mail: mathieu.guillot@usherbrooke.ca [Department of Radiation Oncology, Centre Hospitalier Universitaire de Sherbrooke, 3001 12th Avenue Nord, Sherbrooke, Québec J1H 5N4, Canada and Center for Radiotherapy Research, Department of Nuclear Medicine and Radiobiology, Université de Sherbrooke, 3001 12th Avenue Nord, Sherbrooke, Québec J1H 5N4 (Canada)

    2015-05-15

    Purpose: Targeted and whole-brain irradiation in humans can result in significant side effects causing decreased patient quality of life. To adequately investigate structural and functional alterations after stereotactic radiosurgery, preclinical studies are needed. The purpose of this work is to establish a robust standardized method of targeted irradiation on small regions of the rat brain. Methods: Euthanized male Fischer rats were imaged in a stereotactic bed, by computed tomography (CT), to estimate positioning variations relative to the bregma skull reference point. Using a rat brain atlas and the stereotactic bregma coordinates obtained from CT images, different regions of the brain were delimited and a treatment plan was generated. A single isocenter treatment plan delivering ≥100 Gy in 100% of the target volume was produced by Leksell GammaPlan using the 4 mm diameter collimator of sectors 4, 5, 7, and 8 of the Gamma Knife unit. Impact of positioning deviations of the rat brain on dose deposition was simulated by GammaPlan and validated with dosimetric measurements. Results: The authors’ results showed that 90% of the target volume received 100 ± 8 Gy and the maximum of deposited dose was 125 ± 0.7 Gy, which corresponds to an excellent relative standard deviation of 0.6%. This dose deposition calculated with GammaPlan was validated with dosimetric films resulting in a dose-profile agreement within 5%, both in X- and Z-axes. Conclusions: The authors’ results demonstrate the feasibility of standardizing the irradiation procedure of a small volume in the rat brain using a Gamma Knife.

  15. Clustering of transmutation elements tantalum, rhenium and osmium in tungsten in a fusion environment

    Science.gov (United States)

    You, Yu-Wei; Kong, Xiang-Shan; Wu, Xuebang; Liu, C. S.; Fang, Q. F.; Chen, J. L.; Luo, G.-N.

    2017-08-01

    The formation of transmutation solute-rich precipitates has been reported to seriously degrade the mechanical properties of tungsten in a fusion environment. However, the underlying mechanisms controlling the formation of the precipitates are still unknown. In this study, first-principles calculations are therefore performed to systemically determine the stable structures and binding energies of solute clusters in tungsten consisting of tantalum, rhenium and osmium atoms as well as irradiation-induced vacancies. These clusters are known to act as precursors for the formation of precipitates. We find that osmium can easily segregate to form clusters even in defect-free tungsten alloys, whereas extremely high tantalum and rhenium concentrations are required for the formation of clusters. Vacancies greatly facilitate the clustering of rhenium and osmium, while tantalum is an exception. The binding energies of vacancy-osmium clusters are found to be much higher than those of vacancy-tantalum and vacancy-rhenium clusters. Osmium is observed to strongly promote the formation of vacancy-rhenium clusters, while tantalum can suppress the formation of vacancy-rhenium and vacancy-osmium clusters. The local strain and electronic structure are analyzed to reveal the underlying mechanisms governing the cluster formation. Employing the law of mass action, we predict the evolution of the relative concentration of vacancy-rhenium clusters. This work presents a microscopic picture describing the nucleation and growth of solute clusters in tungsten alloys in a fusion reactor environment, and thereby explains recent experimental phenomena.

  16. Pulsed laser deposition of tantalum pentoxide film

    Science.gov (United States)

    Zhang, J.-Y.; Boyd, I. W.

    We report thin tantalum pentoxide (Ta2O5) films grown on quartz and silicon substrates by the pulsed laser deposition (PLD) technique employing a Nd:YAG laser (wavelength λ=532 nm) in various O2 gas environments. The effect of oxygen pressure, substrate temperature, and annealing under UV irradiation using a 172-nm excimer lamp on the properties of the grown films has been studied. The optical properties determined by UV spectrophotometry were also found to be a sensitive function of oxygen pressure in the chamber. At an O2 pressure of 0.2 mbar and deposition temperatures between 400 and 500 °C, the refractive index of the films was around 2.18 which is very close to the bulk Ta2O5 value of 2.2, and an optical transmittance around 90% in the visible region of the spectrum was obtained. X-ray diffraction measurements showed that the as-deposited films were amorphous at temperatures below 500 °C and possessed an orthorhombic (β-Ta2O5) crystal structure at temperatures above 600 °C. The most significant result of the present study was that oxygen pressure could be used to control the composition and modulate optical band gap of the films. It was also found that UV annealing can significantly improve the optical and electrical properties of the films deposited at low oxygen pressures (<0.1 mbar).

  17. Reduced cost design of liquid lithium target for international fusion material irradiation facility (IFMIF)

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, Hiroo; Ida, Mizuho; Sugimoto, Masayoshi; Takeuchi, Hiroshi [Department of Fussion Engineering Research, Naka Fusion Research Establishment, Japan Atomic Energy Research Institute, Tokai, Ibaraki (Japan); Yutani, Toshiaki [Toshiba Corp., Tokyo (Japan)

    2001-01-01

    The International Fusion Materials Irradiation Facility (IFMIF) is being jointly planned to provide an accelerator-based D-Li neutron source to produce intense high energy neutrons (2 MW/m{sup 2}) up to 200 dpa and a sufficient irradiation volume (500 cm{sup 3}) for testing the candidate materials and components up to about a full lifetime of their anticipated use in ITER and DEMO. To realize such a condition, 40 MeV deuteron beam with a current of 250 mA is injected into high speed liquid lithium flow with a speed of 20 m/s. Following Conceptual Design Activity (1995-1998), a design study with focus on cost reduction without changing its original mission has been done in 1999. The following major changes to the CAD target design have been considered in the study and included in the new design: i) number of the Li target has been changed from 2 to 1, ii) spare of impurity traps of the Li loop was removed although the spare will be stored in a laboratory for quick exchange, iii) building volume was reduced via design changes in lithium loop length. This paper describes the reduced cost design of the lithium target system and recent status of Key Element Technology activities. (author)

  18. Mono-energetic ions emission by nanosecond laser solid target irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Muoio, A., E-mail: Annamaria.Muoio@lns.infn.it [Istituto Nazionale di Fisica Nucleare – Laboratori Nazionali del Sud, Via S. Sofia 62, 95123 Catania (Italy); Dipartimento di Fisica e Scienze della Terra, Università degli Studi di Messina, Viale F.S. D’Alcontres 31, 98166 Messina (Italy); Tudisco, S. [Istituto Nazionale di Fisica Nucleare – Laboratori Nazionali del Sud, Via S. Sofia 62, 95123 Catania (Italy); Altana, C. [Istituto Nazionale di Fisica Nucleare – Laboratori Nazionali del Sud, Via S. Sofia 62, 95123 Catania (Italy); Dipartimento di Fisica e Astronomia, Università degli Studi di Catania, Via S. Sofia 64, 95123 Catania (Italy); Lanzalone, G. [Istituto Nazionale di Fisica Nucleare – Laboratori Nazionali del Sud, Via S. Sofia 62, 95123 Catania (Italy); Università degli Studi di Enna “Kore”, Via delle Olimpiadi, 94100 Enna (Italy); Mascali, D.; Cirrone, G.A.P.; Schillaci, F. [Istituto Nazionale di Fisica Nucleare – Laboratori Nazionali del Sud, Via S. Sofia 62, 95123 Catania (Italy); Trifirò, A. [Dipartimento di Fisica e Scienze della Terra, Università degli Studi di Messina, Viale F.S. D’Alcontres 31, 98166 Messina (Italy); Sezione INFN, Catania (Italy)

    2016-09-01

    An experimental campaign aiming to investigate the acceleration mechanisms through laser–matter interaction in nanosecond domain has been carried out at the LENS (Laser Energy for Nuclear Science) laboratory of INFN-LNS, Catania. Pure Al targets were irradiated by 6 ns laser pulses at different pumping energies, up to 2 J. Advanced diagnostics tools were used to characterize the plasma plume and ion production. We show the preliminary results of this experimental campaign, and especially the ones showing the production of multicharged ions having very narrow energy spreads.

  19. Phase and structural states in the NiTi-based alloy surface layer formed by electron-ion-plasma methods using tantalum

    Energy Technology Data Exchange (ETDEWEB)

    Neiman, Aleksei A., E-mail: nasa@ispms.tsc.ru; Lotkov, Aleksandr I.; Gudimova, Ekaterina Y. [Institute of Strength Physics and Materials Science SB RAS, Tomsk, 634055 (Russian Federation); Meisner, Ludmila L., E-mail: meisner2l@yahoo.com; Semin, Viktor O. [Institute of Strength Physics and Materials Science SB RAS, Tomsk, 634055 (Russian Federation); National Research Tomsk State University, Tomsk, 634050 (Russian Federation)

    2015-10-27

    The paper reports on a study of regularities of formation gradient nano-, submicron and microstructural conditions in the surface layers of the samples after pulsed electron-beam melting of tantalum coating on the substrate NiTi alloy. Experimentally revealed the presence of submicron columnar structure in the upper layers of the tantalum coating. After irradiation modified NiTi surface takes on a layered structure in which each layer differs in phase composition and structural phase state.

  20. Structural modification of tantalum crystal induced by nitrogen ion implantation

    Indian Academy of Sciences (India)

    A H RAMEZANI; M R HANTEHZADEH; M GHORANNEVISS; E DARABI

    2016-06-01

    This paper investigates the effect of nitrogen ion implantation on tantalum surface structure. In this experiment, nitrogen ions which had an energy of 30 keV and doses of $1 \\times 10^{17}$ to $10 \\times 10^{17}$ ions cm$^{−2}$ were used. X-ray diffraction analysis (XRD) was applied for both the metallic Ta substrate and the study of new structures that have been created through the nitrogen ion implantation. Atomic force microscopy (AFM) was also used tocheck the roughness variations prior to and also after the implantation phase. The experimental results show the formation of hexagonal tantalum nitride (TaN$_{0.43}$) in addition to the fact that by increasing the ion dose, the nitrogen atoms occupy more interstitial spaces in the target crystal. The nitride phase also seen for $3\\times 10^{17}$ and $5\\times 10^{17}$ ions cm$^{−2}$, while it disappeared for higher dose of $7\\times 10^{17}$ and $1\\times 10^{18}$ ions cm$^{−2}$. The FWHM of the dominant peak of tantalum nitride suggest the growth of the crystallite’s size, which is in agreement with the AFM results ofthe grains.

  1. Nanostructured targets irradiation by ns-laser for nuclear astrophysics applications: first results

    Science.gov (United States)

    Muoio, A.; Altana, C.; Frassetto, M.; Lanzalone, G.; Malferrari, L.; Mascali, D.; Odorici, F.; Tudisco, S.

    2017-03-01

    The studies discussed in this work are related to a scientific program that aims to reproduce astrophysical-plasmas in laboratory in order to better understand the nuclear processes involved in the stellar burning. An experimental campaign aiming to investigate the effects of innovative nanostructured targets based on Ni, Fe and Co nanowires on laser energy absorption in the ns time domain has been carried out at the LENS (Laser Energy for Nuclear Science) laboratory of INFN-LNS, Catania. Nanowires structures are tuned to increase the light absorption in the visible and infrared range due possibly to plasmonic excitation driven by the incoming photons. Different diagnostics techniques permit to monitor the plasma and to determine its reproducibility. Targets were then irradiated by Nd:YAG 2J, 6 ns infrared laser (λ = 1064 nm) at different pumping energies. Some preliminary results will be illustrated.

  2. Generation of soft x-ray radiation by laser irradiation of a gas puff xenon target

    Energy Technology Data Exchange (ETDEWEB)

    Fiedorowicz, H.; Bartnik, A.; Szczurek, M. [Military Univ. of Technology, Warsaw (Poland). Inst. of Optoelectronics] [and others

    1995-12-31

    Plasmas produced from laser-irradiated gas puff xenon targets, created by pulsed injection of xenon with high-pressure solenoid valve, offer the possibility of realizing a debrisless x-ray point source for the x-ray lithography applications. In this paper the authors present results of the experimental investigations on the x-ray generation from a gas puff xenon target irradiated with nanosecond high-power laser pulses produced using two different laser facilities: a Nd:glass laser operating at 1.06 {micro}m, which generated 10--15 J pulses in 1 ns FWHM, and Nd:glass slab laser, producing pulses of 10 ns duration with energy reaching 12 J for a 0.53 {micro}m wavelength or 20 J for 1.05 {micro}m. To study the x-ray emission different x-ray diagnostic methods have been used. X-ray spectra were registered using a flat CsAP crystal spectrograph with an x-ray film or a curved KAP crystal spectrograph with a convex curvature to an x-ray CCD readout detector. X-ray images have been taken using pinhole cameras with an x-ray film or a CCD array. X-ray yield was measured with the use of semiconductor detectors (silicon photodiodes or diamond photoconductors).

  3. Experiments and analysis of gold disk targets irradiated by smoothing beams of Xingguang II facilities with 350 nm wavelength

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    @@ Gold disk targets were irradiated using focusing and beam smoothing methods on Xingguang (XG-II) laser facilities with 350 nm wavelength, 0.6 ns pulse width and 20-80 Joules energies. Laser absorption, light scattering and X-ray conversion were experimentally investigated. The experimental results showed that laser absorption and scattered light were about 90% and 10%, respectively, under focusing irradiation, but the laser absorption increased 5%-10% and the scattered light about 1% under the condition of beam smoothing. Compared with the case of focusing irradiation, the laser absorption was effectively improved and the scattered light remarkably dropped under uniform irradiation; then due to the decrease in laser intensity, X-ray conversion increased. This is highly advantageous to the inertial confinement fusion. However, X-ray conversion mechanism basically did not change and X-ray conversion efficiency under beam smoothing and focusing irradiation was basically the same.

  4. Experiments and analysis of gold disk targets irradiated by smoothing beams of Xingguang II facilities with 350 nm wavelength

    Institute of Scientific and Technical Information of China (English)

    JIANG; ShaoEn

    2007-01-01

    Gold disk targets were irradiated using focusing and beam smoothing methods on Xingguang (XG-II) laser facilities with 350 nm wavelength, 0.6 ns pulse width and 20-80 Joules energies. Laser absorption, light scattering and X-ray conversion were experimentally investigated. The experimental results showed that laser absorption and scattered light were about 90% and 10%, respectively, under focusing irradiation, but the laser absorption increased 5%-10% and the scattered light about 1% under the condition of beam smoothing. Compared with the case of focusing irradiation, the laser absorption was effectively improved and the scattered light remarkably dropped under uniform irradiation; then due to the decrease in laser intensity, X-ray conversion increased. This is highly advantageous to the inertial confinement fusion. However, X-ray conversion mechanism basically did not change and X-ray conversion efficiency under beam smoothing and focusing irradiation was basically the same.……

  5. Chlorin e6 Conjugated Interleukin-6 Receptor Aptamers Selectively Kill Target Cells Upon Irradiation

    Directory of Open Access Journals (Sweden)

    Sven Kruspe

    2014-01-01

    Full Text Available Photodynamic therapy (PDT uses the therapeutic properties of light in combination with certain chemicals, called photosensitizers, to successfully treat brain, breast, prostate, and skin cancers. To improve PDT, current research focuses on the development of photosensitizers to specifically target cancer cells. In the past few years, aptamers have been developed to directly deliver cargo molecules into target cells. We conjugated the photosensitizer chlorin e6 (ce6 with a human interleukin-6 receptor (IL-6R binding RNA aptamer, AIR-3A yielding AIR-3A-ce6 for application in high efficient PDT. AIR-3A-ce6 was rapidly and specifically internalized by IL-6R presenting (IL-6R+ cells. Upon light irradiation, targeted cells were selectively killed, while free ce6 did not show any toxic effect. Cells lacking the IL-6R were also not affected by AIR-3A-ce6. With this approach, we improved the target specificity of ce6-mediated PDT. In the future, other tumor-specific aptamers might be used to selectively localize photosensitizers into cells of interest and improve the efficacy and specificity of PDT in cancer and other diseases.

  6. Enhanced electron-positron pair production by ultra intense laser irradiating a compound target

    Science.gov (United States)

    Liu, Jian-Xun; Ma, Yan-Yun; Yu, Tong-Pu; Zhao, Jun; Yang, Xiao-Hu; Gan, Long-Fei; Zhang, Guo-Bo; Zhao, Yuan; Zhang, Shi-Jie; Liu, Jin-Jin; Zhuo, Hong-Bin; Shao, Fu-Qiu; Kawata, Shigeo

    2016-12-01

    High-energy-density electron-positron pairs play an increasingly important role in many potential applications. Here, we propose a scheme for enhanced positron production by an ultra intense laser irradiating a gas-Al compound target via the multi-photon Breit-Wheeler (BW) process. The laser pulse first ionizes the gas and interacts with a near-critical-density plasma, forming an electron bubble behind the laser pulse. A great deal of electrons are trapped and accelerated in the bubble, while the laser front hole-bores the Al target and deforms its front surface. A part of the laser wave is thus reflected by the inner curved target surface and collides with the accelerated electron bunch. Finally, a large number of γ photons are emitted in the forward direction via the Compton back-scattering process and the BW process is initiated. Dense electron-positron pairs are produced with a maximum density of 6.02× {{10}27} m-3. Simulation results show that the positron generation is greatly enhanced in the compound target, where the positron yield is two orders of magnitude greater than that in only the solid slab case. The influences of the laser intensity, gas density and length on the positron beam quality are also discussed, which demonstrates the feasibility of the scheme in practice.

  7. Ultra fine tantalum powder for advanced capacitors

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    @@ Ultra fine tantalum and niobium powders are applicable in many areas of engineering. Of particular significance are high purity powders that are usable in production of high capacitance capacitors and superconductors.

  8. Ultra fine tantalum powder for advanced capacitors

    Institute of Scientific and Technical Information of China (English)

    Nebera; A.; Markusbkin; Yu.; Azarov; V.; Ermolaev; N.

    2005-01-01

    Ultra fine tantalum and niobium powders are applicable in many areas of engineering. Of particular significance are high purity powders that are usable in production of high capacitance capacitors and superconductors.……

  9. High charge, low leakage tantalum powders

    Energy Technology Data Exchange (ETDEWEB)

    Schiele, E. K.; Manley Jr., R. V.; Rerat, C. F.

    1985-10-01

    Tantalum powders for electrolytic capacitors having improved electrical capacity and low direct current leakage characteristics are produced by the introduction of combinations of carbon, nitrogen and sulfur-containing materials.

  10. Development of a PVD-based manufacturing process of monolithic LEU irradiation targets for {sup 99}Mo production

    Energy Technology Data Exchange (ETDEWEB)

    Hollmer, Tobias

    2015-08-03

    {sup 99}Mo is the most important radioisotope in nuclear medicine. It is produced by fission of uranium in irradiation targets. The usage of cylindrical monolithic targets can ensure a safe supply of {sup 99}Mo and at the same reduce the amount of highly radioactive waste generated during production. To manufacture these targets, a novel PVD-based technique was developed. Both the feasibility and the high efficiency of this process were demonstrated in a prototype apparatus.

  11. Design and Demonstration of a Material-Plasma Exposure Target Station for Neutron Irradiated Samples

    Energy Technology Data Exchange (ETDEWEB)

    Rapp, Juergen [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Aaron, A. M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Bell, Gary L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Burgess, Thomas W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Ellis, Ronald James [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Giuliano, D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Howard, R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Kiggans, James O. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Lessard, Timothy L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Ohriner, Evan Keith [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Perkins, Dale E. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Varma, Venugopal Koikal [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-10-20

    Fusion energy is the most promising energy source for the future, and one of the most important problems to be solved progressing to a commercial fusion reactor is the identification of plasma-facing materials compatible with the extreme conditions in the fusion reactor environment. The development of plasma–material interaction (PMI) science and the technology of plasma-facing components are key elements in the development of the next step fusion device in the United States, the so-called Fusion Nuclear Science Facility (FNSF). All of these PMI issues and the uncertain impact of the 14-MeV neutron irradiation have been identified in numerous expert panel reports to the fusion community. The 2007 Greenwald report classifies reactor plasma-facing materials (PFCs) and materials as the only Tier 1 issues, requiring a “. . . major extrapolation from the current state of knowledge, need for qualitative improvements and substantial development for both the short and long term.” The Greenwald report goes on to list 19 gaps in understanding and performance related to the plasma–material interface for the technology facilities needed for DEMO-oriented R&D and DEMO itself. Of the 15 major gaps, six (G7, G9, G10, G12, G13) can possibly be addressed with ORNL’s proposal of an advanced Material Plasma Exposure eXperiment. Establishing this mid-scale plasma materials test facility at ORNL is a key element in ORNL’s strategy to secure a leadership role for decades of fusion R&D. That is to say, our end goal is to bring the “signature facility” FNSF home to ORNL. This project is related to the pre-conceptual design of an innovative target station for a future Material–Plasma Exposure eXperiment (MPEX). The target station will be designed to expose candidate fusion reactor plasma-facing materials and components (PFMs and PFCs) to conditions anticipated in fusion reactors, where PFCs will be exposed to dense high-temperature hydrogen plasmas providing steady

  12. Design and Demonstration of a Material-Plasma Exposure Target Station for Neutron Irradiated Samples

    Energy Technology Data Exchange (ETDEWEB)

    Rapp, Juergen [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Aaron, A. M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Bell, Gary L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Burgess, Thomas W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Ellis, Ronald James [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Giuliano, D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Howard, R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Kiggans, James O. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Lessard, Timothy L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Ohriner, Evan Keith [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Perkins, Dale E. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Varma, Venugopal Koikal [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-10-20

    Fusion energy is the most promising energy source for the future, and one of the most important problems to be solved progressing to a commercial fusion reactor is the identification of plasma-facing materials compatible with the extreme conditions in the fusion reactor environment. The development of plasma–material interaction (PMI) science and the technology of plasma-facing components are key elements in the development of the next step fusion device in the United States, the so-called Fusion Nuclear Science Facility (FNSF). All of these PMI issues and the uncertain impact of the 14-MeV neutron irradiation have been identified in numerous expert panel reports to the fusion community. The 2007 Greenwald report classifies reactor plasma-facing materials (PFCs) and materials as the only Tier 1 issues, requiring a “. . . major extrapolation from the current state of knowledge, need for qualitative improvements and substantial development for both the short and long term.” The Greenwald report goes on to list 19 gaps in understanding and performance related to the plasma–material interface for the technology facilities needed for DEMO-oriented R&D and DEMO itself. Of the 15 major gaps, six (G7, G9, G10, G12, G13) can possibly be addressed with ORNL’s proposal of an advanced Material Plasma Exposure eXperiment. Establishing this mid-scale plasma materials test facility at ORNL is a key element in ORNL’s strategy to secure a leadership role for decades of fusion R&D. That is to say, our end goal is to bring the “signature facility” FNSF home to ORNL. This project is related to the pre-conceptual design of an innovative target station for a future Material–Plasma Exposure eXperiment (MPEX). The target station will be designed to expose candidate fusion reactor plasma-facing materials and components (PFMs and PFCs) to conditions anticipated in fusion reactors, where PFCs will be exposed to dense high-temperature hydrogen plasmas providing steady

  13. Non-targeted effects of photon and particle irradiation and the interaction with the immune system

    Directory of Open Access Journals (Sweden)

    Thomas Ernst Schmid

    2012-07-01

    Full Text Available Ionizing irradiation is an important clinical approach to treat solid tumors. Modern radiation technologies aim to selectively kill tumor cells and protect the surrounding normal tissue. The standard paradigm for radiation effects in cellular systems involves damage of the DNA including DNA double strand breaks, which are considered as most effective in destroying tumor cells. Due to their enhanced physical and radiobiological properties, high linear energy transfer (LET radiation qualities are of special interest in tumor therapy. Future radiation therapy strategies aim to utilize carbon ions to effectively treat highly aggressive tumors. More recently, evidence is emerging for non-DNA targeted effects of radiation, including mutations, chromosomal aberrations and changes in gene expression, which can occur in cells that were not directly exposed to radiation. Radiation oncologists are only gradually beginning to appreciate the clinical relevance of radiation-induced bystander effects, genomic instability and abscopal effects. Since these effects are sensed by the immune system, a combination of immunotherapy and irradiation presents a new therapeutic opportunity in the future.

  14. Systems and methods for managing shared-path instrumentation and irradiation targets in a nuclear reactor

    Science.gov (United States)

    Heinold, Mark R.; Berger, John F.; Loper, Milton H.; Runkle, Gary A.

    2015-12-29

    Systems and methods permit discriminate access to nuclear reactors. Systems provide penetration pathways to irradiation target loading and offloading systems, instrumentation systems, and other external systems at desired times, while limiting such access during undesired times. Systems use selection mechanisms that can be strategically positioned for space sharing to connect only desired systems to a reactor. Selection mechanisms include distinct paths, forks, diverters, turntables, and other types of selectors. Management methods with such systems permits use of the nuclear reactor and penetration pathways between different systems and functions, simultaneously and at only distinct desired times. Existing TIP drives and other known instrumentation and plant systems are useable with access management systems and methods, which can be used in any nuclear plant with access restrictions.

  15. Proton radiography of magnetic field produced by ultra-intense laser irradiating capacity-coil target

    CERN Document Server

    Wang, W W; Chen, J; Cai, H B; He, S K; Zhou, W M; Shan, L Q; Lu, F; Wu, Y C; Hong, W; Liu, D X; Bi, B; Zhang, F; Xue, F B; Li, B Y; Zhang, B; He, Y L; He, W; Jiao, J L; Dong, K G; Zhang, F Q; Deng, Z G; Zhang, Z M; Cui, B; Han, D; Zhou, K N; Wang, X D; Zhao, Z Q; Cao, L F; Zhang, B H; He, X T; Gu, Y Q

    2014-01-01

    Ultra-intense ultra-short laser is firstly used to irradiate the capacity-coil target to generate magnetic field. The spatial structure and temporal evolution of huge magnetic fields were studied with time-gated proton radiography method. A magnetic flux density of 40T was measured by comparing the proton deflection and particle track simulations. Although the laser pulse duration is only 30fs, the generated magnetic field can last for over 100 picoseconds. The energy conversion efficiency from laser to magnetic field can reach as high as ~20%. The results indicate that tens of tesla (T) magnetic field could be produced in many ultra intense laser facilities around the world, and higher magnetic field could be produced by picosecond lasers.

  16. Modeling of fast phase transitions dynamics in metal target irradiated by pico- and femtosecond pulsed laser

    Energy Technology Data Exchange (ETDEWEB)

    Mazhukin, V.I. [Institute of Mathematical Modeling, Russian Academy of Sciences, Miusskaya sq. 4A, 125047 Moscow (Russian Federation); Lobok, M.G. [Institute of Mathematical Modeling, Russian Academy of Sciences, Miusskaya sq. 4A, 125047 Moscow (Russian Federation)], E-mail: immras@orc.ru; Chichkov, B. [Laser Zentrum Hannover e.V. Holleritallee 8, 30419 Hannover (Germany)], E-mail: b.chichkov@lhz.de

    2009-03-01

    We investigate laser pulse influence on aluminum target in irradiance range 10{sup 9} to 10{sup 16} W/cm{sup 2}, pulse duration between 10{sup -8} and 10{sup -15} s, Gaussian time profile with wavelength of 0.8 {mu}m. For all computations energy density was 10 J/cm{sup 2}. Plasma in the evaporated material is generated at the energy density above 10 J/cm{sup 2}as the modeling showed. Long and short laser pulses distinguish by the mechanisms of energy transformation. For short laser pulses there is volumetric energy absorption, together with rapid phase transitions it lead to overheating in solid and liquid states, overheated solid temperature rises up to (6-8)T{sub m}. Under influence of the energy saved in overheated solid, duration of the phase transitions becomes nanosecond, which is several orders of magnitude longer than laser pulse.

  17. Estrogen enhanced cell-cell signalling in breast cancer cells exposed to targeted irradiation

    Directory of Open Access Journals (Sweden)

    Held Kathryn D

    2008-06-01

    Full Text Available Abstract Background Radiation-induced bystander responses, where cells respond to their neighbours being irradiated are being extensively studied. Although evidence shows that bystander responses can be induced in many types of cells, it is not known whether there is a radiation-induced bystander effect in breast cancer cells, where the radiosensitivity may be dependent on the role of the cellular estrogen receptor (ER. This study investigated radiation-induced bystander responses in estrogen receptor-positive MCF-7 and estrogen receptor-negative MDA-MB-231 breast cancer cells. Methods The influence of estrogen and anti-estrogen treatments on the bystander response was determined by individually irradiating a fraction of cells within the population with a precise number of helium-3 using a charged particle microbeam. Damage was scored as chromosomal damage measured as micronucleus formation. Results A bystander response measured as increased yield of micronucleated cells was triggered in both MCF-7 and MDA-MB-231 cells. The contribution of the bystander response to total cell damage in MCF-7 cells was higher than that in MDA-MB-231 cells although the radiosensitivity of MDA-MB-231 was higher than MCF-7. Treatment of cells with 17β-estradiol (E2 increased the radiosensitivity and the bystander response in MCF-7 cells, and the effect was diminished by anti-estrogen tamoxifen (TAM. E2 also increased the level of intracellular reactive oxygen species (ROS in MCF-7 cells in the absence of radiation. In contrast, E2 and TAM had no influence on the bystander response and ROS levels in MDA-MB-231 cells. Moreover, the treatment of MCF-7 cells with antioxidants eliminated both the E2-induced ROS increase and E2-enhanced bystander response triggered by the microbeam irradiation, which indicates that ROS are involved in the E2-enhanced bystander micronuclei formation after microbeam irradiation. Conclusion The observation of bystander responses in breast

  18. Synthesis of specific nanoparticles for targeting tumor angiogenesis using electron-beam irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Deshayes, Stephanie, E-mail: stephanie.deshayes@u-bordeaux2.f [Universite de Bordeaux, UMR CNRS 5084, CNAB, Chimie Bio-Organique, 33076 Bordeaux (France); Ecole Polytechnique, CEA, UMR CNRS 7642, Laboratoire des Solides Irradies, 91128 Palaiseau (France); Maurizot, Victor [Universite de Bordeaux, UMR CNRS 5084, CNAB, Chimie Bio-Organique, 33076 Bordeaux (France); Clochard, Marie-Claude; Berthelot, Thomas; Baudin, Cecile [Ecole Polytechnique, CEA, UMR CNRS 7642, Laboratoire des Solides Irradies, 91128 Palaiseau (France); Deleris, Gerard [Universite de Bordeaux, UMR CNRS 5084, CNAB, Chimie Bio-Organique, 33076 Bordeaux (France)

    2010-03-15

    Angiogenesis plays a critical role in both growth and metastasis of tumors. Vascular endothelial growth factor (VEGF) is an endogenous mediator of tumor angiogenesis. Blocking associations of the VEGF with its corresponding receptors (KDR) have become critical for anti-tumor therapy. A cyclo-peptide (CBO-P11), derived from VEGF, able to inhibit the interaction between the growth factor and its receptor, was synthesized in our laboratory to provide a target for angiogenesis. We have prepared biocompatible poly(vinylidene fluoride) (PVDF) nanoparticles in order to obtain long blood circulating systems. Electron-beam (EB) irradiation was used to activate the PVDF nanoparticles. From electron paramagnetic resonance (EPR) measurements, we studied the radical stability in order to optimize the radio-grafting of acrylic acid (AA). Further functionalization of PVDF-g-PAA nanoparticles with the cyclo-peptide via a spacer arm was also possible by performing coupling reactions. High resolution magic angle spinning nuclear magnetic resonance (HRMAS NMR) and MALDI mass spectrometry allowed us to follow each chemical step of this peptide immobilization. We designed a new nanodevice suggesting a great potential for targeting angiogenesis. 7727-21-1

  19. Enhanced X-ray emission from laser-produced gold plasma by double pulses irradiation of nano-porous targets

    Science.gov (United States)

    Fazeli, R.

    2017-02-01

    Enhancement of the soft X-ray emission including free-free, free-bound and bound-bound emissions from Au nano-porous targets irradiated by single and double laser pulses is studied through numerical simulations. Laser pulses of duration 2 ns are used in calculations considering different prepulse intensities and a fixed intensity of 1013 Wcm-2 for the main pulse. The effects of prepulse intensity and time separation between laser pulses are studied for targets of different porosities. Results show that the X-ray yield can be enhanced significantly by a nano-porous target having optimum initial density. Such enhancement can be more improved when double laser pulses with appropriate delay time and intensities irradiate nano-porous targets. It is shown that the enhancement will be reduced when the prepulse intensity is greater than a specific value.

  20. Diffusion kinetics of nitrogen in tantalum during plasma-nitriding

    Institute of Scientific and Technical Information of China (English)

    张德元; 林勤; 曾卫军; 李放; 许兰萍; 付青峰

    2001-01-01

    The activation energies of nitrogen in tantalum on plasma nitriding conditions were calculated according to the experimental data of hardness of plasma-nitriding of tantalum vs time and temperature. The activation energy calculated is 148.873±0.390  kJ/mol. The depth increasing of nitriding layer with time follows square root relation. The nitriding process of tantalum is controlled by diffusion of nitrogen atoms in tantalum solid solution.

  1. Development of a recycling process for tantalum from capacitor scraps

    Science.gov (United States)

    Mineta, Kunio; Okabe, Toru H.

    2005-02-01

    A process based on oxidation treatment at elevated temperature, followed by mechanical separation and chemical treatment, was investigated to develop an effective process for recycling tantalum from capacitor scraps. By this process, tantalum oxide powder, free of SiO2 or other impurities, was recovered from capacitor scrap. Tantalum powder with 99 mass% purity was recovered by magnesiothermic reduction of the obtained tantalum oxide powder.

  2. Measurements of X-ray doses and spectra produced by picosecond laser-irradiated solid targets.

    Science.gov (United States)

    Yang, Bo; Qiu, Rui; Yu, Minghai; Jiao, Jinlong; Lu, Wei; Yan, Yonghong; Zhang, Bo; Zhang, Zhimeng; Zhou, Weimin; Li, Junli; Zhang, Hui

    2017-02-09

    Experiments have shown that high-intensity laser interaction with a solid target can generate significant X-ray doses. This study was conducted to determine the X-ray doses and spectra produced for picosecond laser-irradiated solid targets. The photon doses and X-ray spectra in the laser forward and side directions were measured using an XG III ps 300 TW laser system. For laser intensities of 7×10(18)-4×10(19)W/cm(2), the maximum photon dose was 16.8 mSv at 50cm with a laser energy of ~153J on a 1-mm Ta target. The photon dose in the forward direction increased more significantly with increasing laser intensity than that in the side direction. For photon energies >300keV, the X-ray spectrum can be fit with an effective temperature distribution of the exponential form, dN/dE = k× exp(-E/Tx). The X-ray temperature Tx increased with the laser intensity in the forward direction with values of 0.46-0.75MeV. Tx was less strongly correlated with the laser intensity in the side direction with values of 0.29-0.32MeV. The escaping electron spectrum was also measured. The measured electron temperature was correlated with the electron temperature predicted by the ponderomotive law. The observations in this experiment were also investigated numerically. A good agreement was observed between the experimental and simulation results.

  3. Mechanical properties and constitutive relations for tantalum and tantalum alloys under high-rate deformation

    Energy Technology Data Exchange (ETDEWEB)

    Chen, S.R.; Gray, G.T. III; Bingert, S.R. [Los Alamos National Lab., NM (United States). Materials Science and Technology Div.

    1996-05-01

    Tantalum and its alloys have received increased interest as a model bcc metal and for defense-related applications. The stress-strain behavior of several tantalums, possessing varied compositions and manufacturing histories, and tantalum alloyed with tungsten, was investigated as a function of temperature from {minus}196 C to 1,000 C, and strain rate from 10{sup {minus}3} s{sup {minus}1} to 8,000 s{sup {minus}1}. The yield stress for all the Ta-materials was found to be sensitive to the test temperature, the impurity and solute contents; however, the strain hardening remained very similar for various ``pure`` tantalums but increased with alloying. Powder-metallurgy (P/M) tantalum with various levels of oxygen content produced via different processing paths was also investigated. Similar mechanical properties compared to conventionally processed tantalums were achieved in the P/M Ta. This data suggests that the frequently observed inhomogeneities in the mechanical behavior of tantalum inherited from conventional processes can be overcome. Constitutive relations based upon the Johnson-Cook, the Zerilli-Armstrong, and the Mechanical Threshold Stress models were evaluated for all the Ta-based materials. Parameters were also fit for these models to a tantalum-bar material. Flow stresses of a Ta bar stock subjected to a large-strain deformation of {var_epsilon} = 1.85 via multiple upset forging were obtained. The capabilities and limitations of each model for large-strain applications are examined. The deformation mechanisms controlling high-rate plasticity in tantalum are revisited.

  4. Results of the six-and-a-half day electron-accelerator irradiation of enriched Mo-100 targets for the production of Mo-99

    Energy Technology Data Exchange (ETDEWEB)

    Chemerisov, S. [Argonne National Lab. (ANL), Argonne, IL (United States); Bailey, J. [Argonne National Lab. (ANL), Argonne, IL (United States); Heltemes, T. [Argonne National Lab. (ANL), Argonne, IL (United States); Jonah, C. [Argonne National Lab. (ANL), Argonne, IL (United States); Makarashvili, V. [Argonne National Lab. (ANL), Argonne, IL (United States); Tkac, P. [Argonne National Lab. (ANL), Argonne, IL (United States); Rotsch, D. [Argonne National Lab. (ANL), Argonne, IL (United States); Virgo, M. [Argonne National Lab. (ANL), Argonne, IL (United States); Vandegrift, G. F. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-10-01

    A six-and-a-half day irradiation of enriched Mo-100 target disks was performed by Argonne’s electron linac. This report describes the irradiation conditions and the means used to process the targets for shipment to NorthStar Medical Isotopes, LLC, for feed to their RadioGenixTM technetium generator.

  5. Analyses of the plasma generated by laser irradiation on sputtered target for determination of the thickness used for plasma generation

    Energy Technology Data Exchange (ETDEWEB)

    Kumaki, Masafumi, E-mail: masafumi.kumaki@riken.jp [Cooperative Major in Nuclear Energy, Waseda University, Shinjuku, Tokyo (Japan); RIKEN, Wako, Saitama (Japan); Ikeda, Shunsuke; Sekine, Megumi; Munemoto, Naoya [RIKEN, Wako, Saitama (Japan); Department of Energy Sciences, Tokyo Institute of Technology, Meguro, Tokyo (Japan); Fuwa, Yasuhiro [RIKEN, Wako, Saitama (Japan); Department of Physics and Astronomy, Kyoto University, Uji, Kyoto (Japan); Cinquegrani, David [American Nuclear Society, University of Michigan, Ann Arbor, Michigan 48109 (United States); Kanesue, Takeshi; Okamura, Masahiro [Collider-Accelerator Department, Brookhaven National Laboratory, Upton, New York 11973 (United States); Washio, Masakazu [Cooperative Major in Nuclear Energy, Waseda University, Shinjuku, Tokyo (Japan)

    2014-02-15

    In Brookhaven National Laboratory, laser ion source has been developed to provide heavy ion beams by using plasma generation with 1064 nm Nd:YAG laser irradiation onto solid targets. The laser energy is transferred to the target material and creates a crater on the surface. However, only the partial material can be turned into plasma state and the other portion is considered to be just vaporized. Since heat propagation in the target material requires more than typical laser irradiation period, which is typically several ns, only the certain depth of the layers may contribute to form the plasma. As a result, the depth is more than 500 nm because the base material Al ions were detected. On the other hand, the result of comparing each carbon thickness case suggests that the surface carbon layer is not contributed to generate plasma.

  6. Demonstration of a neonlike argon soft-x-ray laser with a picosecond-laser-irradiated gas puff target.

    Science.gov (United States)

    Fiedorowicz, H; Bartnik, A; Dunn, J; Smith, R F; Hunter, J; Nilsen, J; Osterheld, A L; Shlyaptsev, V N

    2001-09-15

    We demonstrate a neonlike argon-ion x-ray laser, using a short-pulse laser-irradiated gas puff target. The gas puff target was formed by pulsed injection of gas from a high-pressure solenoid valve through a nozzle in the form of a narrow slit and irradiated with a combination of long, 600-ps and short, 6-ps high-power laser pulses with a total of 10 J of energy in a traveling-wave excitation scheme. Lasing was observed on the 3p (1)S(0)?3s (1)P(1) transition at 46.9 nm and the 3d (1)P(1)?3p (1)P(1) transition at 45.1 nm. A gain of 11 cm(-1) was measured on these transitions for targets up to 0.9 cm long.

  7. Performance of target irradiation in a high-power laser with a continuous phase plate and spectral dispersion.

    Science.gov (United States)

    Jiang, Xiujuan; Li, Jinghui; Wu, Rong; Zhu, Zhengtao; Zhou, Shenlei; Lin, Zunqi

    2013-11-01

    We report on the performance of target irradiation at the SG-II high-power laser facility with a continuous phase plate (CPP) and the technique of smoothing by spectral dispersion (SSD). Simulative and experimental results are presented, where the irradiation uniformity and energy concentration of the target spots are analyzed. The results show that the designed CPP can focus the spot energy into the desired region and shape a profile with steep edge and flat top, but the actual performance of the fabricated CPP needs some improvements. It is also proved that the CPP is insensitive to the long-scale wavefront distortion in the incident beam. The one-dimensional SSD configuration evidently works in smoothing the fine-scale intensity modulation inside the target spot.

  8. A mechanistic study of gold nanoparticle radiosensitisation using targeted microbeam irradiation

    Science.gov (United States)

    Ghita, Mihaela; McMahon, Stephen J.; Taggart, Laura E.; Butterworth, Karl T.; Schettino, Giuseppe; Prise, Kevin M.

    2017-01-01

    Gold nanoparticles (GNPs) have been demonstrated as effective radiosensitizing agents in a range of preclinical models using broad field sources of various energies. This study aimed to distinguish between these mechanisms by applying subcellular targeting using a soft X-ray microbeam in combination with GNPs. DNA damage and repair kinetics were determined following nuclear and cytoplasmic irradiation using a soft X-ray (carbon K-shell, 278 eV) microbeam in MDA-MB-231 breast cancer and AG01522 fibroblast cells with and without GNPs. To investigate the mechanism of the GNP induced radiosensitization, GNP-induced mitochondrial depolarisation was quantified by TMRE staining, and levels of DNA damage were compared in cells with depolarised and functional mitochondria. Differential effects were observed following radiation exposure between the two cell lines. These findings were validated 24 hours after removal of GNPs by flow cytometry analysis of mitochondrial depolarisation. This study provides further evidence that GNP radiosensitisation is mediated by mitochondrial function and it is the first report applying a soft X-ray microbeam to study the radiobiological effects of GNPs to enable the separation of physical and biological effects. PMID:28300190

  9. SU-D-304-02: Magnetically Focused Proton Irradiation of Small Field Targets

    Energy Technology Data Exchange (ETDEWEB)

    McAuley, GA; Slater, JM [Loma Linda University, Loma Linda, CA (United States); Slater, JD; Wroe, AJ [Loma Linda University Medical Center, Loma Linda, CA (United States)

    2015-06-15

    Purpose: To investigate the use of magnetic focusing for small field proton irradiations. It is hypothesized that magnetic focusing will provide significant dose distribution benefits over standard collimated beams for fields less than 10 mm diameter. Methods: Magnets consisting of 24 segments of radiation hard samarium-cobalt adhered into hollow cylinders were designed and manufactured. Two focusing magnets were placed on a positioning track on our Gantry 1 treatment table. Proton beams with energies of 127 and 157 MeV, 15 and 30 mm modulation, and 8 mm initial diameters were delivered to a water tank using single-stage scattering. Depth dose distributions were measured using a PTW PR60020 diode detector and transverse profiles were measured with Gafchromic EBT3 film. Monte Carlo simulations were also performed - both for comparison with experimental data and to further explore the potential of magnetic focusing in silica. For example, beam spot areas (based on the 90% dose contour) were matched at Bragg depth between simulated 100 MeV collimated beams and simulated beams focused by two 400 T/m gradient magnets. Results: Preliminary experimental results show 23% higher peak to entrance dose ratios and flatter spread out Bragg peak plateaus for 8 mm focused beams compared with uncollimated beams. Monte Carlo simulations showed 21% larger peak to entrance ratios and a ∼9 fold more efficient dose to target delivery compared to spot-sized matched collimated beams. Our latest results will be presented. Conclusion: Our results suggest that rare earth focusing magnet assemblies could reduce skin dose and beam number while delivering dose to nominally spherical radiosurgery targets over a much shorter time compared to unfocused beams. Immediate clinical applications include those associated with proton radiosurgery and functional radiosurgery of the brain and spine, however expanded treatment sites can be also envisaged.

  10. First results of the irradiation program of inert matrices, targets and fuels for minor actinides transmutation in fast reactor

    Energy Technology Data Exchange (ETDEWEB)

    Bonnerot, Jean-Marc; Ferroud-Plattet, Marie-Pierre; Lamontagne, Jerome [CEA Cadarache, Nuclear Energy Direction, Saint-Paul les Durance Cedex, 13108 (France); Warin, Dominique [CEA Valrho, Nuclear Energy Direction, DRCP, Bagnols-sur-Ceze Cedex, 30207 (France); Gosmain, Lionel [CEA Saclay, Nuclear Energy Direction, DMN, Gif sur Yvette, 91190 (France)

    2008-07-01

    A comprehensive irradiation program was started in France in 1992 to demonstrate the technical feasibility of the transmutation of minor actinides in current and future nuclear reactors, by means of inert support targets or dedicated fuels. The first step of the program (MATINA program) consisted in the irradiation of various inert materials intended as support matrix for transmutation targets, in the fast reactor Phenix, to select the best candidates. These inert materials included as well oxide and nitride ceramics - MgO, MgAl{sub 2}O{sub 4}, Al{sub 2}O{sub 3}, Y{sub 3}Al{sub 5}O{sub 12} and TiN - as refractory metals - W, Nb, Cr and V- and were irradiated under fast neutron flux at temperatures ranged between 650 and 1040 deg. C. The results show that in comparison to MgO, MgAl{sub 2}O{sub 4} and Al{sub 2}O{sub 3} inert matrices irradiated alone, the composite pellets containing UO{sub 2} particles, showed very different behaviors under irradiation. The swelling of MgO pellets is enhanced in the presence of fissile material whereas it is lowered for the Al{sub 2}O{sub 3}-UO{sub 2} pellets. MgAl{sub 2}O{sub 4}-UO{sub 2} pellets remained stable. The second step of the program aimed at testing the behavior of inert support targets containing americium. A new experiment ECRIX H involving composite pellets with an MgO matrix and AmO{sub 2-x} particles was performed in Phenix and completed in 2006. A rather low elongation of the pellet stack was observed and no significant diameter deformation of cladding was detected after irradiation. The analysis of the filling gas of the pin after puncturing, revealed that respectively 28% and 5% of the He and Xe+Kr created under irradiation were released in the expanding volume of the pin. ECRIX H, which is the first experiment on Am base target in Phenix, will undoubtedly represent a very important step in the general design approach about inert matrix support targets once the complete results should be available by the end of

  11. Self-overcoming of the boiling condition by pressure increment in a water target irradiated by proton beam

    Energy Technology Data Exchange (ETDEWEB)

    Hong, Bong Hwan, E-mail: burnn@kirams.re.kr [Korea Institute of Radiological and Medical Sciences (KIRMAS), 75 Nowon-Gil, Nowon-Gu, Seoul 139-706 (Korea, Republic of); Kang, Joonsun; Jung, In Su; Ram, Han Ga; Park, Yeun Soo [Korea Institute of Radiological and Medical Sciences (KIRMAS), 75 Nowon-Gil, Nowon-Gu, Seoul 139-706 (Korea, Republic of); Cho, Hyung Hee [Department of Mechanical Engineering, Yonsei University, 134 Sinchon-Dong, Seodaemun-Gu, Seoul 120-749 (Korea, Republic of)

    2013-11-11

    An experiment was conducted to examine and visualize the boiling phenomena inside a water target by irradiating it with a proton beam from MC-50 cyclotron. The boiling phenomena were recorded with a CMOS camera. While an increase of the fraction of the water vapor volume is generally considered to be normal when water is boiled by a proton beam, our experiment showed the opposite result. The volume expansion of the liquid water exceeded the compressibility of the initial air volume. A grid structure in front of the entrance window foil held the target volume constant. Therefore, the phenomena inside the target underwent an isochoric process, and the pressure inside the target was increased rapidly beyond the pressure at the boiling point. Consequently, there was no more bulk boiling in the Bragg-peak region in the target water. Our results show that the boiling of the water can be controlled by controlling the equilibrium pressure of the water target.

  12. Deuteron irradiation of W and WO3 for production of high specific activity (186)Re: Challenges associated with thick target preparation.

    Science.gov (United States)

    Balkin, Ethan R; Gagnon, Katherine; Strong, Kevin T; Smith, Bennett E; Dorman, Eric F; Emery, Robert C; Pauzauskie, Peter J; Fassbender, Michael E; Cutler, Cathy S; Ketring, Alan R; Jurisson, Silvia S; Wilbur, D Scott

    2016-09-01

    This investigation evaluated target fabrication and beam parameters for scale-up production of high specific activity (186)Re using deuteron irradiation of enriched (186)W via the (186)W(d,2n)(186)Re reaction. Thick W and WO3 targets were prepared, characterized and evaluated in deuteron irradiations. Full-thickness targets, as determined using SRIM, were prepared by uniaxially pressing powdered natural abundance W and WO3, or 96.86% enriched (186)W, into Al target supports. Alternatively, thick targets were prepared by pressing (186)W between two layers of graphite powder or by placing pre-sintered (1105°C, 12h) natural abundance WO3 pellets into an Al target support. Assessments of structural integrity were made on each target prepared. Prior to irradiation, material composition analyses were conducted using SEM, XRD, and Raman spectroscopy. Within a minimum of 24h post irradiation, gamma-ray spectroscopy was performed on all targets to assess production yields and radionuclidic byproducts. Problems were encountered with the structural integrity of some pressed W and WO3 pellets before and during irradiation, and target material characterization results could be correlated with the structural integrity of the pressed target pellets. Under the conditions studied, the findings suggest that all WO3 targets prepared and studied were unacceptable. By contrast, (186)W metal was found to be a viable target material for (186)Re production. Thick targets prepared with powdered (186)W pressed between layers of graphite provided a particularly robust target configuration.

  13. Growth of ZnO nanostructures by femtosecond laser irradiation of polycrystalline targets

    Science.gov (United States)

    Escalante, G.; Ryu, Y. K.; de la Cruz, A. Ruíz; Puerto, D.; Solís, J.; Fernández, P.

    2015-11-01

    The formation of LIPSS upon irradiation with ultrashort laser pulses on the surface of polycrystalline ZnO samples and the potential use of irradiated areas as growth patterns for the production of highly ordered nanostructures upon redeposition have been studied. For this purpose, we have performed different sets of irradiation experiments including static irradiation experiments at low and high repetition rates, as well as scanned beam experiments at high repetition rate, this later in order to generate relatively large template regions for nanostructure growth by redeposition. In all cases, LIPSS formation has been achieved in the ZnO polycrystalline surface. Under appropriate irradiation conditions, the material is redeposited rendering a high density of nanostructures with high aspect ratios and good crystal quality. Given the special luminescent properties and applications of ZnO, particular attention has been paid to the luminescence properties after irradiation and after post-irradiation thermal treatments. The observed evolution has been correlated with evolution of point defects in the treated surfaces. Thermal treatments cause significant changes in both the topography and the cathodoluminescent emission, such as the development of laminar structures, the emergence of nucleation centers and the recovery of ultraviolet emission previously quenched as a consequence of irradiation. Interestingly, LIPSS remain after the luminescent recovery by thermal annealing, opening the possibility to control both luminescence properties and grain size while maintaining an ordered structure with a high effective surface area.

  14. Measurement of prompt gamma profiles in inhomogeneous targets with a knife-edge slit camera during proton irradiation

    Science.gov (United States)

    Priegnitz, M.; Helmbrecht, S.; Janssens, G.; Perali, I.; Smeets, J.; Vander Stappen, F.; Sterpin, E.; Fiedler, F.

    2015-06-01

    Proton and ion beam therapies become increasingly relevant in radiation therapy. To fully exploit the potential of this irradiation technique and to achieve maximum target volume conformality, the verification of particle ranges is highly desirable. Many research activities focus on the measurement of the spatial distributions of prompt gamma rays emitted during irradiation. A passively collimating knife-edge slit camera is a promising option to perform such measurements. In former publications, the feasibility of accurate detection of proton range shifts in homogeneous targets could be shown with such a camera. We present slit camera measurements of prompt gamma depth profiles in inhomogeneous targets. From real treatment plans and their underlying CTs, representative beam paths are selected and assembled as one-dimensional inhomogeneous targets built from tissue equivalent materials. These phantoms have been irradiated with monoenergetic proton pencil beams. The accuracy of range deviation estimation as well as the detectability of range shifts is investigated in different scenarios. In most cases, range deviations can be detected within less than 2 mm. In close vicinity to low-density regions, range detection is challenging. In particular, a minimum beam penetration depth of 7 mm beyond a cavity is required for reliable detection of a cavity filling with the present setup. Dedicated data post-processing methods may be capable of overcoming this limitation.

  15. Measurement of prompt gamma profiles in inhomogeneous targets with a knife-edge slit camera during proton irradiation.

    Science.gov (United States)

    Priegnitz, M; Helmbrecht, S; Janssens, G; Perali, I; Smeets, J; Vander Stappen, F; Sterpin, E; Fiedler, F

    2015-06-21

    Proton and ion beam therapies become increasingly relevant in radiation therapy. To fully exploit the potential of this irradiation technique and to achieve maximum target volume conformality, the verification of particle ranges is highly desirable. Many research activities focus on the measurement of the spatial distributions of prompt gamma rays emitted during irradiation. A passively collimating knife-edge slit camera is a promising option to perform such measurements. In former publications, the feasibility of accurate detection of proton range shifts in homogeneous targets could be shown with such a camera. We present slit camera measurements of prompt gamma depth profiles in inhomogeneous targets. From real treatment plans and their underlying CTs, representative beam paths are selected and assembled as one-dimensional inhomogeneous targets built from tissue equivalent materials. These phantoms have been irradiated with monoenergetic proton pencil beams. The accuracy of range deviation estimation as well as the detectability of range shifts is investigated in different scenarios. In most cases, range deviations can be detected within less than 2 mm. In close vicinity to low-density regions, range detection is challenging. In particular, a minimum beam penetration depth of 7 mm beyond a cavity is required for reliable detection of a cavity filling with the present setup. Dedicated data post-processing methods may be capable of overcoming this limitation.

  16. Proton emission from thin hydrogenated targets irradiated by laser pulses at 1016 W/cm2a)

    Science.gov (United States)

    Torrisi, L.; Giuffrida, L.; Cutroneo, M.; Cirrone, P.; Picciotto, A.; Krasa, J.; Margarone, D.; Velyhan, A.; Laska, L.; Ullschmied, J.; Wolowski, J.; Badziak, J.; Rosinski, M.

    2012-02-01

    The iodine laser at PALS Laboratory in Prague, operating at 1315 nm fundamental harmonics and at 300 ps FWHM pulse length, is employed to irradiate thin hydrogenated targets placed in vacuum at intensities on the order of 1016 W/cm2. The laser-generated plasma is investigated in terms of proton and ion emission in the forward and backward directions. The time-of-flight technique, using ion collectors and semiconductor detectors, is used to measure the ion currents and the corresponding velocities and energies. Thomson parabola spectrometer is employed to separate the contribution of the ion emission from single laser shots. A particular attention is given to the proton production in terms of the maximum energy, emission yield, and angular distribution as a function of the laser energy, focal position, target thickness, and composition. Metallic and polymeric targets allow to generate protons with large energy range and different yield, depending on the laser, target composition, and target geometry properties.

  17. Enhancement of laser to X-ray conversion by counter-propagating laser beams irradiating thin gold targets

    Science.gov (United States)

    Zhao, Y.; Ge, Z. Y.; Ma, Y. Y.; Yang, X. H.; Xu, B. B.; Ramis, R.

    2017-03-01

    X-ray emission from laser irradiating solid target is an important X-ray source for various potential applications. Counter-propagating (C-P) laser beams configuration is proposed to enhance the laser to X-ray conversion efficiency (CE) from laser irradiating solid targets. One-dimensional radiation hydrodynamics simulations show that the total X-ray CE for the C-P lasers case is as high as 65%, which has a 13% improvement compared with the single laser case. The improvement is mainly caused by the enlarged radiation region, and the enhancement of X-ray emission is from soft X-ray. Detailed energy term distributions and influences of the foil thickness on the X-ray CEs for both cases are presented. It is found that the enhancement of radiation is attributed to lower thermal and kinetic energy of the C-P lasers scheme.

  18. Electrodepositions on Tantalum in alkali halide melts

    DEFF Research Database (Denmark)

    Barner, Jens H. Von; Jensen, Annemette Hindhede; Christensen, Erik

    2012-01-01

    in a single 4 electron step. By electrolyses at a constant potential of - 1.4 V vs. Pt in a NaCl-KCl-NaF-Na2CO3 melt at 800 °C coherent carbon containing surface layers could be obtained on tantalum substrates, when a CO2 atmosphere was applied. Copyright © 2012 by The Electrochemical Society....

  19. Bone remodeling around cementless tantalum cups

    NARCIS (Netherlands)

    Grillo, J. -C.; Flecher, X.; Bouvenot, J.; Argenson, J. -N.

    2008-01-01

    Purpose of the study.-Most studies have reported a significant decrease in periacetabular bone stock one year after implantation of a cementless cup. The purpose of this work was to study the bone-implant interface of the tantalum cup using plain X-rays and dual-energy X-ray absorptiometry (DEXA). M

  20. Chemical mechanical polishing of tantalum and tantalum nitride

    Science.gov (United States)

    Janjam, Sathish Babu S. V.

    There is a continuing need in the semiconductor industry to clear residual copper (Cu) and planarize the tantalum (Ta)/tantalum nitride (TaN) barrier/etch stop layer with a higher removal rate using the technique of Chemical Mechanical Polishing (CMP). Obtaining high removal rates for Ta/TaN is very challenging as the films are very hard, and hence it is difficult to achieve high Ta/TaN removal rates by just relying on an increase in the mechanical forces (operating pressure) alone during CMP. Ta/TaN is an inert metal, therefore, obtaining high Ta/TaN removal rates by using chemical additives is also challenging. Not only Ta/TaN needs to be removed at a higher rate in the second step of polishing, but also remaining Cu should be cleared. It is important to search for novel chemicals that can form a thin film on the Ta/TaN surface which can be easily abraded by the polishing pad with very less pressure. In this work, oxalic and tartaric acids have been investigated as the complexing agents in slurries for Ta/TaN CMP. Oxalic and tartaric acids appear to be reactive with Ta in the presence of hydrogen peroxide. A dispersion of the Oxalic acid (OA)/Tartaric Acid (TA) - peroxide mixtures with silica (fumed/colloidal) can be used to achieve Ta removal rates that are ˜ 90 nm/min at pH between 3 to 6 by applying a down force of 6.3 psi, where as at a lower down force of 2 psi, a removal rate of ˜ 40 nm/min has been achieved at pH = 3. It was shown earlier that a high Cu removal rate can be obtained using OA-peroxide based slurries with/without the addition of abrasives at pH = 3 [1]. So, in the first step, Cu could be removed at high rates at pH = 3 and by changing the pH to 5 or 6, Ta/TaN can be removed as mentioned above. Hence these slurries could be used as "single dispersion slurries " that could be used for both the first and second steps of Cu CMP. During the second step (barrier layer polish), Cu removal rates are low but not low enough to minimize dishing with

  1. The scattering fields for a spherical target irradiated by a plane electromagnetic wave in an arbitrary direction

    Institute of Scientific and Technical Information of China (English)

    Li Ying-Le; Huang Ji-Ying

    2006-01-01

    The relation between corresponding trigonometric functions in two rotating coordinate systems is presented. The transformation formula for a vector in the two rotating spherical coordinate systems is obtained. The scattering fields for a spherical target irradiated by a plane electromagnetic wave in an arbitrary direction are derived. These fields in a particular case retrogress to those available in the literature. The obtained results have great potential in practical applications.

  2. Influence of Different Moderator Materials on Characteristics of Neutron Fluxes Generated under Irradiation of Lead Target with Proton Beams

    CERN Document Server

    Sosnin, A N; Polanski, A; Petrochenkov, S A; Golovatyuk, V M; Krivopustov, M I; Bamblevski, V P; Westmeier, W; Odoj, R; Brandt, R; Robotham, H; Hashemi-Nezhad, S R; Zamani-Valassiadou, M

    2002-01-01

    Neutron fields generated in extended heavy (Z\\geq 82) targets under irradiation with proton beams at energies in the range of 1 GeV are investigated. Influence of different moderators on the spectra and multiplicities of neutrons escaping the surface of the assembly consisting of a lead target (\\varnothing 8 cm\\times 20 cm or \\varnothing 8cm\\times 50 cm) screened by variable thickness of polyethylene or graphite, respectively, was compared in the present work. It is shown that the effectiveness of graphite as a material used in such assemblies to moderate spallation neutrons down to thermal energies is significantly lower than that of paraffin.

  3. Possible version of the compression degradation of the thermonuclear indirect-irradiation targets at the national ignition facility and a reason for the failure of ignition

    Science.gov (United States)

    Rozanov, V. B.; Vergunova, G. A.

    2017-01-01

    The main parameters of compression of a target and tendencies at change in the irradiation conditions are determined by analyzing the published results of experiments at the megajoule National Ignition Facility (NIF) on the compression of capsules in indirect-irradiation targets by means of the one-dimensional RADIAN program in the spherical geometry. A possible version of the "failure of ignition" of an indirect-irradiation target under the NIF conditions is attributed to radiation transfer. The application of onedimensional model to analyze the National Ignition Campaign (NIC) experiments allows identifying conditions corresponding to the future ignition regime and distinguishing them from conditions under which ignition does not occur.

  4. Possible version of the compression degradation of the thermonuclear indirect-irradiation targets at the national ignition facility and a reason for the failure of ignition

    Energy Technology Data Exchange (ETDEWEB)

    Rozanov, V. B., E-mail: rozanov@sci.lebedev.ru; Vergunova, G. A., E-mail: verg@sci.lebedev.ru [Russian Academy of Sciences, Lebedev Physical Institute (Russian Federation)

    2017-01-15

    The main parameters of compression of a target and tendencies at change in the irradiation conditions are determined by analyzing the published results of experiments at the megajoule National Ignition Facility (NIF) on the compression of capsules in indirect-irradiation targets by means of the one-dimensional RADIAN program in the spherical geometry. A possible version of the “failure of ignition” of an indirect-irradiation target under the NIF conditions is attributed to radiation transfer. The application of onedimensional model to analyze the National Ignition Campaign (NIC) experiments allows identifying conditions corresponding to the future ignition regime and distinguishing them from conditions under which ignition does not occur.

  5. Parallel computation safety analysis irradiation targets fission product molybdenum in neutronic aspect using the successive over-relaxation algorithm

    Science.gov (United States)

    Susmikanti, Mike; Dewayatna, Winter; Sulistyo, Yos

    2014-09-01

    One of the research activities in support of commercial radioisotope production program is a safety research on target FPM (Fission Product Molybdenum) irradiation. FPM targets form a tube made of stainless steel which contains nuclear-grade high-enrichment uranium. The FPM irradiation tube is intended to obtain fission products. Fission materials such as Mo99 used widely the form of kits in the medical world. The neutronics problem is solved using first-order perturbation theory derived from the diffusion equation for four groups. In contrast, Mo isotopes have longer half-lives, about 3 days (66 hours), so the delivery of radioisotopes to consumer centers and storage is possible though still limited. The production of this isotope potentially gives significant economic value. The criticality and flux in multigroup diffusion model was calculated for various irradiation positions and uranium contents. This model involves complex computation, with large and sparse matrix system. Several parallel algorithms have been developed for the sparse and large matrix solution. In this paper, a successive over-relaxation (SOR) algorithm was implemented for the calculation of reactivity coefficients which can be done in parallel. Previous works performed reactivity calculations serially with Gauss-Seidel iteratives. The parallel method can be used to solve multigroup diffusion equation system and calculate the criticality and reactivity coefficients. In this research a computer code was developed to exploit parallel processing to perform reactivity calculations which were to be used in safety analysis. The parallel processing in the multicore computer system allows the calculation to be performed more quickly. This code was applied for the safety limits calculation of irradiated FPM targets containing highly enriched uranium. The results of calculations neutron show that for uranium contents of 1.7676 g and 6.1866 g (× 106 cm-1) in a tube, their delta reactivities are the still

  6. Thorium silicate compound as a solid-state target for production of isomeric thorium-229 nuclei by electron beam irradiation

    Science.gov (United States)

    Borisyuk, P. V.; Vasilyev, O. S.; Lebedinskii, Y. Y.; Krasavin, A. V.; Tkalya, E. V.; Troyan, V. I.; Habibulina, R. F.; Chubunova, E. V.; Yakovlev, V. P.

    2016-09-01

    In this paper, we discuss an idea of the experiment for excitation of the isomeric transition in thorium-229 nuclei by irradiating with electron beam targets with necessary physical characteristics. The chemical composition and bandgap of ThSi10O22 were determined by X-ray photoelectron spectroscopy and reflection electron energy loss spectroscopy. It was found that the energy gap is equal to 7.7 eV and does not change when the target is exposed to a medium energy electron beam for a long time. This indicates that the compound possesses high electron-beam resistance. A quantitative estimation of the output function of isomeric thorium-229 nuclei generated by interaction of nuclei with the secondary electron flow formed by irradiating the solid-state ThSi10O22-based target is given. The estimation shows that ThSi10O22 is a promising thorium-containing target for investigating excitation of the nuclear low-lying isomeric transition in the thorium-229 isotope using medium-energy electrons.

  7. Investigations of ultrafast charge dynamics in laser-irradiated targets by a self probing technique employing laser driven protons

    Energy Technology Data Exchange (ETDEWEB)

    Ahmed, H. [School of Mathematics and Physics, Queen' s University Belfast, BT7 1NN (United Kingdom); Kar, S., E-mail: s.kar@qub.ac.uk [School of Mathematics and Physics, Queen' s University Belfast, BT7 1NN (United Kingdom); Cantono, G. [School of Mathematics and Physics, Queen' s University Belfast, BT7 1NN (United Kingdom); Department of Physics “E. Fermi”, Largo B. Pontecorvo 3, 56127 Pisa (Italy); Consiglio Nazionale delle Ricerche, Istituto Nazionale di Ottica, Research Unit Adriano Gozzini, via G. Moruzzi 1, Pisa 56124 (Italy); Nersisyan, G. [School of Mathematics and Physics, Queen' s University Belfast, BT7 1NN (United Kingdom); Brauckmann, S. [Institut für Laser-und Plasmaphysik, Heinrich-Heine-Universität, Düsseldorf (Germany); Doria, D.; Gwynne, D. [School of Mathematics and Physics, Queen' s University Belfast, BT7 1NN (United Kingdom); Macchi, A. [Department of Physics “E. Fermi”, Largo B. Pontecorvo 3, 56127 Pisa (Italy); Consiglio Nazionale delle Ricerche, Istituto Nazionale di Ottica, Research Unit Adriano Gozzini, via G. Moruzzi 1, Pisa 56124 (Italy); Naughton, K. [School of Mathematics and Physics, Queen' s University Belfast, BT7 1NN (United Kingdom); Willi, O. [Institut für Laser-und Plasmaphysik, Heinrich-Heine-Universität, Düsseldorf (Germany); Lewis, C.L.S.; Borghesi, M. [School of Mathematics and Physics, Queen' s University Belfast, BT7 1NN (United Kingdom)

    2016-09-01

    The divergent and broadband proton beams produced by the target normal sheath acceleration mechanism provide the unique opportunity to probe, in a point-projection imaging scheme, the dynamics of the transient electric and magnetic fields produced during laser-plasma interactions. Commonly such experimental setup entails two intense laser beams, where the interaction produced by one beam is probed with the protons produced by the second. We present here experimental studies of the ultra-fast charge dynamics along a wire connected to laser irradiated target carried out by employing a ‘self’ proton probing arrangement – i.e. by connecting the wire to the target generating the probe protons. The experimental data shows that an electromagnetic pulse carrying a significant amount of charge is launched along the wire, which travels as a unified pulse of 10s of ps duration with a velocity close to speed of light. The experimental capabilities and the analysis procedure of this specific type of proton probing technique are discussed. - Highlights: • Prompt charging of laser irradiated target generates ultra-short EM pulses. • Its ultrafast propagation along a wire was studied by self-proton probing technique. • Self-proton probing technique is the proton probing with one laser pulse. • Pulse temporal profile and speed along the wire were measured with high resolution.

  8. Thorium silicate compound as a solid-state target for production of isomeric thorium-229 nuclei by electron beam irradiation

    Directory of Open Access Journals (Sweden)

    P. V. Borisyuk

    2016-09-01

    Full Text Available In this paper, we discuss an idea of the experiment for excitation of the isomeric transition in thorium-229 nuclei by irradiating with electron beam targets with necessary physical characteristics. The chemical composition and bandgap of ThSi10O22 were determined by X-ray photoelectron spectroscopy and reflection electron energy loss spectroscopy. It was found that the energy gap is equal to 7.7 eV and does not change when the target is exposed to a medium energy electron beam for a long time. This indicates that the compound possesses high electron-beam resistance. A quantitative estimation of the output function of isomeric thorium-229 nuclei generated by interaction of nuclei with the secondary electron flow formed by irradiating the solid-state ThSi10O22-based target is given. The estimation shows that ThSi10O22 is a promising thorium-containing target for investigating excitation of the nuclear low-lying isomeric transition in the thorium-229 isotope using medium-energy electrons.

  9. Post-irradiation analysis of an ISOLDE lead-bismuth target: Stable and long-lived noble gas nuclides

    Science.gov (United States)

    Leya, I.; Grimberg, A.; David, J.-C.; Schumann, D.; Neuhausen, J.; Zanini, L.; Noah, E.

    2016-07-01

    We measured the isotopic concentrations of long-lived and stable He, Ne, Ar, Kr, and Xe isotopes in a sample from a lead-bismuth eutectic target irradiated with 1.0 and 1.4 GeV protons. Our data indicate for most noble gases nearly complete release with retention fractions in the range of percent or less. Higher retention fractions result from the decay of long-lived radioactive progenitors from groups 1, 2, or 7 of the periodic table. From the data we can calculate a retention fraction for 3H of 2-3%. For alkaline metals we find retention fractions of about 10%, 30%, and 50% for Na, Rb, and Cs, respectively. For the alkaline earth metal Ba we found complete retention. Finally, the measured Kr and Xe concentrations indicate that there was some release of the halogens Br and I during and/or after the irradiation.

  10. Tantalum oxide thin films as protective coatings for sensors

    DEFF Research Database (Denmark)

    Christensen, Carsten; Reus, Roger De; Bouwstra, Siebe

    1999-01-01

    Reactively sputtered tantalum oxide thin films have been investigated as protective coatings for aggressive media exposed sensors. Tantalum oxide is shown to be chemically very robust. The etch rate in aqueous potassium hydroxide with pH 11 at 140°C is lower than 0.008 Å h-l. Etching in liquids...... annealing O2 in the residual thin-film stress can be altered from compressive to tensile and annealing at 450°C for 30 minutes gives a stress-free film. The step coverage of the sputter deposited amorphous tantalum oxide is reasonable, but metallization lines are hard to cover. Sputtered tantalum oxide...

  11. Tantalum oxide barrier in magnetic tunnel junctions

    Institute of Scientific and Technical Information of China (English)

    Guanghua Yu; Tingting Ren; Wei Ji; Jiao Teng; Fengwu Zhu

    2004-01-01

    Tantalum as an insulating barrier can take the place of Al in magnetic tunnel junctions (MTJs). Ta barriers in MTJs were fabricated by natural oxidation. X-ray photoelectron spectroscopy (XPS) was used to characterize the oxidation states of Ta barrier.The experimental results show that the chemical state of tantalum is pure Ta5+ and the thickness of the oxide is 1.3 nm. The unoxidized Ta in the barrier may chemically reacted with NiFe layer which is usually used in MTJs to form an intermetallic compound,NiTa2. A magnetic "dead layer" could be produced in the NiFe/Ta interface. The "dead layer" is likely to influence the spinning electron transport and the magnetoresistance effect.

  12. Development of a Charged Particle Microbeam for Targeted and Single Particle Subcellular Irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Yanch, Jacquelyn C.

    2004-03-12

    The development of a charged particle microbeam for single particle, subcellular irradiations at the Massachusetts Institute of Technology Laboratory for Accelerator Beam Applications (MIT LABA) was initiated under this NEER aeard. The Microbeam apparatus makes use of a pre-existing electrostatic accelerator with a horizontal beam tube.

  13. First Principles Force Field for Metallic Tantalum

    OpenAIRE

    Strachan, Alejandro; Cagin, Tahir; Gulseren, Oguz; Mukherjee, Sonali; Cohen, Ronald E.; Goddard III, William A.

    2002-01-01

    We propose a general strategy to develop accurate Force Fields (FF) for metallic systems derived from ab initio quantum mechanical (QM) calculations; we illustrate this approach for tantalum. As input data to the FF we use the linearized augmented plane wave method (LAPW) with the generalized gradient approximation (GGA) to calculate: (i) the zero temperature equation of state (EOS) of Ta for bcc, fcc, and hcp crystal structures for pressures up to ~500 GPa. (ii) Elastic constants. (iii) We u...

  14. Comparison of Irradiation and Wolbachia Based Approaches for Sterile-Male Strategies Targeting Aedes albopictus.

    Science.gov (United States)

    Atyame, Célestine M; Labbé, Pierrick; Lebon, Cyrille; Weill, Mylène; Moretti, Riccardo; Marini, Francesca; Gouagna, Louis Clément; Calvitti, Maurizio; Tortosa, Pablo

    2016-01-01

    The global expansion of Aedes albopictus together with the absence of vaccines for most of the arboviruses transmitted by this mosquito has stimulated the development of sterile-male strategies aiming at controlling disease transmission through the suppression of natural vector populations. In this context, two environmentally friendly control strategies, namely the Sterile Insect Technique (SIT) and the Wolbachia-based Incompatible Insect Technique (IIT) are currently being developed in several laboratories worldwide. So far however, there is a lack of comparative assessment of these strategies under the same controlled conditions. Here, we compared the mating capacities, i.e. insemination capacity, sterilization capacity and mating competitiveness of irradiated (35 Gy) and incompatible Ae. albopictus males at different ages and ratios under laboratory controlled conditions. Our data show that there was no significant difference in insemination capacity of irradiated and incompatible males, both male types showing lower capacities than untreated males at 1 day but recovering full capacity within 5 days following emergence. Regarding mating competitiveness trials, a global observed trend is that incompatible males tend to induce a lower hatching rate than irradiated males in cage controlled confrontations. More specifically, incompatible males were found more competitive than irradiated males in 5:1 ratio regardless of age, while irradiated males were only found more competitive than incompatible males in the 1:1 ratio at 10 days old. Overall, under the tested conditions, IIT seemed to be slightly more effective than SIT. However, considering that a single strategy will likely not be adapted to all environments, our data stimulates the need for comparative assessments of distinct strategies in up-scaled conditions in order to identify the most suitable and safe sterilizing technology to be implemented in a specific environmental setting and to identify the

  15. Magnetron sputter deposited tantalum and tantalum nitride thin films: An analysis of phase, hardness and composition

    Energy Technology Data Exchange (ETDEWEB)

    Bernoulli, D. [Laboratory for Nanometallurgy, Department of Materials, ETH-Zurich, Wolfgang-Pauli-Strasse 10, CH-8093 Zürich (Switzerland); Müller, U. [EMPA, Swiss Federal Laboratories for Material Science and Technology, Überlandstrasse 129, CH-8600 Dübendorf (Switzerland); Schwarzenberger, M. [Laboratory for Nanometallurgy, Department of Materials, ETH-Zurich, Wolfgang-Pauli-Strasse 10, CH-8093 Zürich (Switzerland); Hauert, R. [EMPA, Swiss Federal Laboratories for Material Science and Technology, Überlandstrasse 129, CH-8600 Dübendorf (Switzerland); Spolenak, R. [Laboratory for Nanometallurgy, Department of Materials, ETH-Zurich, Wolfgang-Pauli-Strasse 10, CH-8093 Zürich (Switzerland)

    2013-12-02

    Tantalum (Ta) and tantalum nitride thin films are highly important as diffusion barriers and adhesion layers in microelectronics and hard coatings for cutting tools. In this study, the effect of the underlying substrate on the phase formation of Ta and the influence of a changing N{sub 2}/Ar flow ratio on hardness, phase and composition of reactively formed tantalum nitride have been investigated. Ta is DC sputter deposited and forms β-Ta on amorphous diamond-like carbon and on the amorphous natural oxide layers of Ti and Si(100) while a 15 nm TaN seed layer results in the formation of α-Ta. The chemical composition of the topmost layers of a substrate influences the formation of α- and β-Ta. With increasing N{sub 2}/Ar flow ratios a transition from amorphous Ta-rich tantalum nitride over face-centered cubic tantalum nitride (fcc-TaN) to (100) textured fcc-TaN at flow ratios above 45% is observed. The hardness of the tantalum nitride thin film reaches a maximum at a flow ratio of 45%, followed by a decrease in hardness for higher N{sub 2}/Ar flow ratios. The increase in hardness is associated with a decrease in grain size and shows a stronger correlation for a Meyers and Ashworth relationship than for a Hall–Petch relationship. - Highlights: • Chemical composition of the substrate influences the phase of deposited Ta. • FCC-TaN seed layer leads to α-Ta on the natural oxide layers of Ti and Si(100). • Meyers and Ashworth relationship correlates stronger than Hall–Petch relationship.

  16. Production of medical isotopes from a thorium target irradiated by light charged particles up to 70 MeV

    Science.gov (United States)

    Duchemin, C.; Guertin, A.; Haddad, F.; Michel, N.; Métivier, V.

    2015-02-01

    The irradiation of a thorium target by light charged particles (protons and deuterons) leads to the production of several isotopes of medical interest. Direct nuclear reaction allows the production of Protactinium-230 which decays to Uranium-230 the mother nucleus of Thorium-226, a promising isotope for alpha radionuclide therapy. The fission of Thorium-232 produces fragments of interest like Molybdenum-99, Iodine-131 and Cadmium-115g. We focus our study on the production of these isotopes, performing new cross section measurements and calculating production yields. Our new sets of data are compared with the literature and the last version of the TALYS code.

  17. Production of medical isotopes from a thorium target irradiated by light charged particles up to 70 MeV.

    Science.gov (United States)

    Duchemin, C; Guertin, A; Haddad, F; Michel, N; Métivier, V

    2015-02-07

    The irradiation of a thorium target by light charged particles (protons and deuterons) leads to the production of several isotopes of medical interest. Direct nuclear reaction allows the production of Protactinium-230 which decays to Uranium-230 the mother nucleus of Thorium-226, a promising isotope for alpha radionuclide therapy. The fission of Thorium-232 produces fragments of interest like Molybdenum-99, Iodine-131 and Cadmium-115g. We focus our study on the production of these isotopes, performing new cross section measurements and calculating production yields. Our new sets of data are compared with the literature and the last version of the TALYS code.

  18. The study of neutron spectra in water bath from Pb target irradiated by 250MeV/u protons

    CERN Document Server

    Li, Yanyan; Ju, Yongqin; Ma, Fei; Zhang, Hongbin; Chen, Liang; Ge, Honglin; Luo, Peng; Zhou, Bin; Zhang, Yanbin; Li, Jianyang; Xu, Junkui; Wang, Songlin; Yang, Yongwei; Yang, Lei

    2014-01-01

    The spallation neutrons were produced by the irradiation of Pb with 250 MeV protons. The Pb target was surrounded by water which was used to slow down the emitted neutrons. The moderated neutrons in the water bath were measured by using the resonance detectors of Au, Mn and In with Cd cover. According to the measured activities of the foils, the neutron flux at different resonance energy were deduced and the epithermal neutron spectra were proposed. Corresponding results calculated with the Monte Carlo code MCNPX were compared with the experimental data to check the validity of the code.

  19. Computational study of the generation of crystal defects in a bcc metal target irradiated by short laser pulses

    Science.gov (United States)

    Lin, Zhibin; Johnson, Robert A.; Zhigilei, Leonid V.

    2008-06-01

    The generation of crystal defects in a Cr target irradiated by a short, 200 fs, laser pulse is investigated in computer simulations performed with a computational model that combines the classical molecular dynamics method with a continuum description of the laser excitation of conduction band electrons, electron-phonon coupling, and electron heat conduction. Interatomic interactions are described by the embedded atom method (EAM) potential with a parametrization designed for Cr. The potential is tested by comparing the properties of the EAM Cr material with experimental data and predictions of density functional theory calculations. The simulations are performed at laser fluences close to the threshold for surface melting. Fast temperature variation and strong thermoelastic stresses produced by the laser pulse are causing surface melting and epitaxial resolidification, transient appearance of a high density of stacking faults along the {110} planes, and generation of a large number of point defects (vacancies and self-interstitials). The stacking faults appear as a result of internal shifts in the crystal undergoing a rapid uniaxial expansion in the direction normal to the irradiated surface. The stacking faults are unstable and disappear shortly after the laser-induced tensile stress wave leaves the surface region of the target. Thermally activated generation of vacancy-interstitial pairs during the initial temperature spike and quick escape of highly mobile self-interstitials to the melting front or the free surface of the target, along with the formation of vacancies at the solid-liquid interface during the fast resolidification process, result in a high density of vacancies, on the order of 10-3 per lattice site, created in the surface region of the target. The strong supersaturation of vacancies can be related to the incubation effect in multipulse laser ablation/damage and should play an important role in mixing/alloying of multicomponent or composite

  20. Advances in the chemical vapor deposition (CVD) of Tantalum

    DEFF Research Database (Denmark)

    Mugabi, James Atwoki; Eriksen, Søren; Christensen, Erik

    2014-01-01

    The chemical stability of tantalum in hot acidic media has made it a key material in the protection of industrial equipment from corrosion under such conditions. The Chemical Vapor Deposition of tantalum to achieve such thin corrosion resistant coatings is one of the most widely mentioned examples...

  1. Tantalum: A strategic metal; Tantalo: Un metal estrategico

    Energy Technology Data Exchange (ETDEWEB)

    Lopez-Lopez, G.; Lopez-Lopez, J.; Garcia-Yagues, M. R.

    2009-07-01

    In nature, the main source of tantalum is an isomorphous series of minerals containing oxides of tantalum, niobium, iron and manganese, which are collectively known as columbine-tantalite (coltan). Upgraded Ta{sub 2}O{sub 5}-containing tin slags are also used as a secondary source of tantalum. Coltan, either naturally occurring or synthetically produced as concentrates from tin slags, are digested with hydrofluoric and sulphuric acid at an elevated temperature. the aqueous solution of ta-Nb in hydrofluoric acid is extracted in several continuously operating mixer-settler systems or extraction columns with an organic solvent like methyl isobutyl ketone. The organic phase is then scrubbed with 6-15 N H{sub 2}SO{sub 4} to separate the niobium from the tantalum by selective stripping. The tantalum salt is extracted from the organic phase with water or diluted aqueous ammonium fluoride solution, the demands of the solid tantalum capacitor industry for high quality, high surface area tantalum powders have driven improvements in the sodium reduction of K{sub 2}TaF{sub 7}. The much-improved chemistry reflects the many modifications to the process put in place after 1990 and the subsequent improvements in the electrical quality as measured by the performance of tantalum capacitors. (Author) 5 refs.

  2. Parallel computation safety analysis irradiation targets fission product molybdenum in neutronic aspect using the successive over-relaxation algorithm

    Energy Technology Data Exchange (ETDEWEB)

    Susmikanti, Mike, E-mail: mike@batan.go.id [Center for Development of Nuclear Informatics, National Nuclear Energy Agency, PUSPIPTEK, Tangerang (Indonesia); Dewayatna, Winter, E-mail: winter@batan.go.id [Center for Nuclear Fuel Technology, National Nuclear Energy Agency, PUSPIPTEK, Tangerang (Indonesia); Sulistyo, Yos, E-mail: soj@batan.go.id [Center for Nuclear Equipment and Engineering, National Nuclear Energy Agency, PUSPIPTEK, Tangerang (Indonesia)

    2014-09-30

    One of the research activities in support of commercial radioisotope production program is a safety research on target FPM (Fission Product Molybdenum) irradiation. FPM targets form a tube made of stainless steel which contains nuclear-grade high-enrichment uranium. The FPM irradiation tube is intended to obtain fission products. Fission materials such as Mo{sup 99} used widely the form of kits in the medical world. The neutronics problem is solved using first-order perturbation theory derived from the diffusion equation for four groups. In contrast, Mo isotopes have longer half-lives, about 3 days (66 hours), so the delivery of radioisotopes to consumer centers and storage is possible though still limited. The production of this isotope potentially gives significant economic value. The criticality and flux in multigroup diffusion model was calculated for various irradiation positions and uranium contents. This model involves complex computation, with large and sparse matrix system. Several parallel algorithms have been developed for the sparse and large matrix solution. In this paper, a successive over-relaxation (SOR) algorithm was implemented for the calculation of reactivity coefficients which can be done in parallel. Previous works performed reactivity calculations serially with Gauss-Seidel iteratives. The parallel method can be used to solve multigroup diffusion equation system and calculate the criticality and reactivity coefficients. In this research a computer code was developed to exploit parallel processing to perform reactivity calculations which were to be used in safety analysis. The parallel processing in the multicore computer system allows the calculation to be performed more quickly. This code was applied for the safety limits calculation of irradiated FPM targets containing highly enriched uranium. The results of calculations neutron show that for uranium contents of 1.7676 g and 6.1866 g (× 10{sup 6} cm{sup −1}) in a tube, their delta

  3. Efficient and stable proton acceleration by irradiating a two-layer target with a linearly polarized laser pulse

    Energy Technology Data Exchange (ETDEWEB)

    Wang, H. Y.; Yan, X. Q.; Chen, J. E.; He, X. T. [State Key Laboratory of Nuclear Physics and Technology, Peking University, Beijing 100871 (China) and Key Lab of High Energy Density Physics Simulation, CAPT, Peking University, Beijing 100871 (China); Ma, W. J.; Bin, J. H.; Schreiber, J.; Tajima, T.; Habs, D. [Fakultaet fuer Physik, Ludwig-Maximilians-Universitaet Muenchen, Am Coulombwall 1, 85748 Garching (Germany) and Max-Planck-Institut fuer Quantenoptik, Hans-Kopfermann-Str. 1, 85748 Garching (Germany)

    2013-01-15

    We report an efficient and stable scheme to generate {approx}200 MeV proton bunch by irradiating a two-layer targets (near-critical density layer+solid density layer with heavy ions and protons) with a linearly polarized Gaussian pulse at intensity of 6.0 Multiplication-Sign 10{sup 20} W/cm{sup 2}. Due to self-focusing of laser and directly accelerated electrons in the near-critical density layer, the proton energy is enhanced by a factor of 3 compared to single-layer solid targets. The energy spread of proton is also remarkably reduced. Such scheme is attractive for applications relevant to tumor therapy.

  4. Proton emission from thin hydrogenated targets irradiated by laser pulses at 10{sup 16} W/cm{sup 2}

    Energy Technology Data Exchange (ETDEWEB)

    Torrisi, L. [INFN-LNS Via S. Sofia 44, 95123 Catania (Italy); Dip.to di Fisica, Universita di Messina, V.le F.S. D' Alcontres 31, 98166 S. Agata, Messina (Italy); Giuffrida, L.; Cirrone, P. [INFN-LNS Via S. Sofia 44, 95123 Catania (Italy); Cutroneo, M. [Dip.to di Fisica, Universita di Messina, V.le F.S. D' Alcontres 31, 98166 S. Agata, Messina (Italy); Picciotto, A. [Fondazione Bruno Kessler-IRST, Via Sommarive 18, 38050 Povo, Trento (Italy); Krasa, J.; Margarone, D.; Velyhan, A.; Laska, L.; Ullschmied, J. [Institute of Physics, ASCR, v.v.i., 182 21 Prague 8 (Czech Republic); Wolowski, J.; Badziak, J.; Rosinski, M. [Institute of Plasma Physics and Laser Microfusion, IPPLM, 23 Hery Str. 01-497 Warsaw (Poland)

    2012-02-15

    The iodine laser at PALS Laboratory in Prague, operating at 1315 nm fundamental harmonics and at 300 ps FWHM pulse length, is employed to irradiate thin hydrogenated targets placed in vacuum at intensities on the order of 10{sup 16} W/cm{sup 2}. The laser-generated plasma is investigated in terms of proton and ion emission in the forward and backward directions. The time-of-flight technique, using ion collectors and semiconductor detectors, is used to measure the ion currents and the corresponding velocities and energies. Thomson parabola spectrometer is employed to separate the contribution of the ion emission from single laser shots. A particular attention is given to the proton production in terms of the maximum energy, emission yield, and angular distribution as a function of the laser energy, focal position, target thickness, and composition. Metallic and polymeric targets allow to generate protons with large energy range and different yield, depending on the laser, target composition, and target geometry properties.

  5. Proton emission from thin hydrogenated targets irradiated by laser pulses at 10(16) W∕cm2.

    Science.gov (United States)

    Torrisi, L; Giuffrida, L; Cutroneo, M; Cirrone, P; Picciotto, A; Krasa, J; Margarone, D; Velyhan, A; Laska, L; Ullschmied, J; Wolowski, J; Badziak, J; Rosinski, M

    2012-02-01

    The iodine laser at PALS Laboratory in Prague, operating at 1315 nm fundamental harmonics and at 300 ps FWHM pulse length, is employed to irradiate thin hydrogenated targets placed in vacuum at intensities on the order of 10(16) W∕cm(2). The laser-generated plasma is investigated in terms of proton and ion emission in the forward and backward directions. The time-of-flight technique, using ion collectors and semiconductor detectors, is used to measure the ion currents and the corresponding velocities and energies. Thomson parabola spectrometer is employed to separate the contribution of the ion emission from single laser shots. A particular attention is given to the proton production in terms of the maximum energy, emission yield, and angular distribution as a function of the laser energy, focal position, target thickness, and composition. Metallic and polymeric targets allow to generate protons with large energy range and different yield, depending on the laser, target composition, and target geometry properties.

  6. Technical Note: Immunohistochemical evaluation of mouse brain irradiation targeting accuracy with 3D-printed immobilization device

    Energy Technology Data Exchange (ETDEWEB)

    Zarghami, Niloufar, E-mail: nzargham@uwo.ca; Jensen, Michael D. [Department of Medical Biophysics, The University of Western Ontario, 1151 Richmond Street, London, Ontario N6A 3K7 (Canada); Talluri, Srikanth; Dick, Frederick A. [Department of Biochemistry, The University of Western Ontario, 1151 Richmond Street, London, Ontario N6A 3K7 (Canada); London Regional Cancer Program, London Health Sciences Centre, 800 Commissioners Road East, London, Ontario N6A 5W9 (Canada); Foster, Paula J. [Imaging Research Laboratories, Robarts Research Institute, 100 Perth Drive, London, Ontario N6A 5K8 (Canada); Department of Medical Biophysics, The University of Western Ontario, 1151 Richmond Street, London, Ontario N6A 3K7 (Canada); Chambers, Ann F. [Department of Medical Biophysics, The University of Western Ontario, 1151 Richmond Street, London, Ontario N6A 3K7 (Canada); Department of Oncology, The University of Western Ontario, 1151 Richmond Street, London, Ontario N6A 3K7 (Canada); London Regional Cancer Program, London Health Sciences Centre, 800 Commissioners Road East, London, Ontario N6A 5W9 (Canada); Wong, Eugene [Department of Physics and Astronomy, The University of Western Ontario, 1151 Richmond Street, London, Ontario N6A 3K7 (Canada); Department of Medical Biophysics, The University of Western Ontario, 1151 Richmond Street, London, Ontario N6A 3K7 (Canada); Department of Oncology, The University of Western Ontario, 1151 Richmond Street, London, Ontario N6A 3K7 (Canada); London Regional Cancer Program, London Health Sciences Centre, 800 Commissioners Road East, London, Ontario N6A 5W9 (Canada)

    2015-11-15

    Purpose: Small animal immobilization devices facilitate positioning of animals for reproducible imaging and accurate focal radiation therapy. In this study, the authors demonstrate the use of three-dimensional (3D) printing technology to fabricate a custom-designed mouse head restraint. The authors evaluate the accuracy of this device for the purpose of mouse brain irradiation. Methods: A mouse head holder was designed for a microCT couch using CAD software and printed in an acrylic based material. Ten mice received half-brain radiation while positioned in the 3D-printed head holder. Animal placement was achieved using on-board image guidance and computerized asymmetric collimators. To evaluate the precision of beam localization for half-brain irradiation, mice were sacrificed approximately 30 min after treatment and brain sections were stained for γ-H2AX, a marker for DNA breaks. The distance and angle of the γ-H2AX radiation beam border to longitudinal fissure were measured on histological samples. Animals were monitored for any possible trauma from the device. Results: Visualization of the radiation beam on ex vivo brain sections with γ-H2AX immunohistochemical staining showed a sharp radiation field within the tissue. Measurements showed a mean irradiation targeting error of 0.14 ± 0.09 mm (standard deviation). Rotation between the beam axis and mouse head was 1.2° ± 1.0° (standard deviation). The immobilization device was easily adjusted to accommodate different sizes of mice. No signs of trauma to the mice were observed from the use of tooth block and ear bars. Conclusions: The authors designed and built a novel 3D-printed mouse head holder with many desired features for accurate and reproducible radiation targeting. The 3D printing technology was found to be practical and economical for producing a small animal imaging and radiation restraint device and allows for customization for study specific needs.

  7. Direct flow separation strategy, to isolate no-carrier-added {sup 90}Nb from irradiated Mo or Zr targets

    Energy Technology Data Exchange (ETDEWEB)

    Radchenko, Valery; Roesch, Frank [Mainz Univ. (Germany). Inst. of Nuclear Chemistry; Filosofov, Dmitry V.; Dadakhanov, Jakhongir [Joint Institute of Nuclear Research, Dubna (Russian Federation). Dzhelepov Laboratory of Nuclear Problems; Karaivanov, Dimitar V. [Joint Institute of Nuclear Research, Dubna (Russian Federation). Dzhelepov Laboratory of Nuclear Problems; Bulgarian Academy of Sciences, Sofia (Bulgaria). Inst. for Nuclear Research and Nuclear Energy; Marinova, Atanaska [Joint Institute of Nuclear Research, Dubna (Russian Federation). Dzhelepov Laboratory of Nuclear Problems; Sofia Univ. (Bulgaria). Faculty of Chemistry and Pharmacy; Baimukhanova, Ayagoz [Joint Institute of Nuclear Research, Dubna (Russian Federation). Dzhelepov Laboratory of Nuclear Problems; Institute of Nuclear Physics of the Republic of Kazakhstan, Almaty (Kazakhstan)

    2016-11-01

    {sup 90}Nb has an intermediate half-life of 14.6 h, a high positron branching of 53% and optimal β{sup +} emission energy of only E{sub mean} 0.35 MeV per decay. These favorable characteristics suggest it may be a potential candidate for application in immuno-PET. Our recent aim was to conduct studies on distribution coefficients for Zr{sup IV} and Nb{sup V} in mixtures of HCl/H{sub 2}O{sub 2} and HCl/oxalic acid for anion exchange resin (AG 1 x 8) and UTEVA resin to develop a ''direct flow'' separation strategy for {sup 90}Nb. The direct flow concept refers to a separation accomplished using a single eluent on multiple columns, effectively streamlining the separation process and increasing the time efficiency. Finally, we also demonstrated that this separation strategy is applicable to the production of the positron emitter {sup 90}Nb via the irradiation of molybdenum targets and isolation of {sup 90}Nb from the irradiated molybdenum target.

  8. Target irradiation induced bystander effects between stem-like and non stem-like cancer cells.

    Science.gov (United States)

    Liu, Yu; Kobayashi, Alisa; Maeda, Takeshi; Fu, Qibin; Oikawa, Masakazu; Yang, Gen; Konishi, Teruaki; Uchihori, Yukio; Hei, Tom K; Wang, Yugang

    2015-03-01

    Tumors are heterogeneous in nature and consist of multiple cell types. Among them, cancer stem-like cells (CSCs) are suggested to be the principal cause of tumor metastasis, resistance and recurrence. Therefore, understanding the behavior of CSCs in direct and indirect irradiations is crucial for clinical radiotherapy. Here, the CSCs and their counterpart non stem-like cancer cells (NSCCs) in human HT1080 fibrosarcoma cell line were sorted and labeled, then the two cell subtypes were mixed together and chosen separately to be irradiated via a proton microbeam. The radiation-induced bystander effect (RIBE) between the CSCs and NSCCs was measured by imaging 53BP1 foci, a widely used indicator for DNA double strand break (DSB). CSCs were found to be less active than NSCCs in both the generation and the response of bystander signals. Moreover, the nitric oxide (NO) scavenger c-PTIO can effectively alleviate the bystander effect in bystander NSCCs but not in bystander CSCs, indicating a difference of the two cell subtypes in NO signal response. To our knowledge, this is the first report shedding light on the RIBE between CSCs and NSCCs, which might contribute to a further understanding of the out-of-field effect in cancer radiotherapy. Copyright © 2015 Elsevier B.V. All rights reserved.

  9. Results of four one-day electron-accelerator irradiations of enriched Mo-100 targets for the production of Mo-99

    Energy Technology Data Exchange (ETDEWEB)

    Chemerisov, S. [Argonne National Lab. (ANL), Argonne, IL (United States); Bailey, J. [Argonne National Lab. (ANL), Argonne, IL (United States); Heltemes, T. [Argonne National Lab. (ANL), Argonne, IL (United States); Jonah, C. [Argonne National Lab. (ANL), Argonne, IL (United States); Gromov, R. [Argonne National Lab. (ANL), Argonne, IL (United States); Makarashvili, V. [Argonne National Lab. (ANL), Argonne, IL (United States); Tkac, P. [Argonne National Lab. (ANL), Argonne, IL (United States); Rotsch, D. [Argonne National Lab. (ANL), Argonne, IL (United States); Virgo, M. [Argonne National Lab. (ANL), Argonne, IL (United States); Vandegrift, G. F. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-10-01

    A series of four one-day irradiations was conducted with 100Mo-enriched disk targets. After irradiation, the enriched disks were removed from the target and dissolved. The resulting solution was processed using a NorthStar RadioGenix™ 99mTc generator either at Argonne National Laboratory or at the NorthStar Medical Radioisotopes facility. Runs on the RadioGenix system produced inconsistent analytical results for 99mTc in the Tc/Mo solution. These inconsistencies were attributed to the impurities in the solution or improper column packing. During the irradiations, the performance of the optic transitional radiation (OTR) and infrared cameras was tested in high radiation field. The OTR cameras survived all irradiations, while the IR cameras failed every time. The addition of X-ray and neutron shielding improved camera survivability and decreased the number of upsets.

  10. Distribution characteristic of scattering field for an ellipsoidal target irradiated by an electromagnetic wave from an arbitrary direction

    Institute of Scientific and Technical Information of China (English)

    Li Ying-Le; Huang Ji-Ying; Wang Ming-Jun; Zhang Jia-Tian

    2008-01-01

    It is of great importance for enginsering applications to obtain the expression of scattering field for an ellipsoidal target irradiated by an electromagnetic wave from an arbitrary direction.Literature relevant to this problem is seldom found.In this paper,the scattering field for an ellipsoidal target is presented by utilizing the scale transformation of electromagnetic field and the rotation of coordinate system,with an electromagnetic wave projecting on the target from an arbitrary direction.The obtained result is in good agreement with the solution available from the literature if we consider the scale factors to be unity.Taking a conducting ellipsoidal target for sample,we perform the partial simulations of the ellipsoidat model and a plant leaf model by choosing different scale factors.The obtained results show that the distribution characteristic of scattering field is sensitively affected by the polarization of the incident wave and varies not much with the incident wave angle but changes with the observation point.At some points the scattering energy arrives at its maximum.

  11. Fracture of an uncemented tantalum patellar component

    Directory of Open Access Journals (Sweden)

    Nathan L. Grimm, MD

    2016-06-01

    Full Text Available A 62-year-old man presented with the acute, atraumatic onset of pain 3 years after uncemented right total knee arthroplasty. He complained of new mechanical locking with the knee held in extension on examination and unable to flex the knee. On the plain radiographs, the patellar component peg was fractured and the plate was dislocated. The knee was immobilized, and revision to a cemented 3-peg component was performed. Fracture of a single-peg, tantalum-backed uncemented patellar component has not been described. Clinical suspicion for this should be given in the setting of acute locking. We recommend revision with a cemented polyethylene component.

  12. Inter- and Intrafraction Target Motion in Highly Focused Single Vocal Cord Irradiation of T1a Larynx Cancer Patients

    Energy Technology Data Exchange (ETDEWEB)

    Kwa, Stefan L.S., E-mail: s.kwa@erasmusmc.nl; Al-Mamgani, Abrahim; Osman, Sarah O.S.; Gangsaas, Anne; Levendag, Peter C.; Heijmen, Ben J.M.

    2015-09-01

    Purpose: The purpose of this study was to verify clinical target volume–planning target volume (CTV-PTV) margins in single vocal cord irradiation (SVCI) of T1a larynx tumors and characterize inter- and intrafraction target motion. Methods and Materials: For 42 patients, a single vocal cord was irradiated using intensity modulated radiation therapy at a total dose of 58.1 Gy (16 fractions × 3.63 Gy). A daily cone beam computed tomography (CBCT) scan was performed to online correct the setup of the thyroid cartilage after patient positioning with in-room lasers (interfraction motion correction). To monitor intrafraction motion, CBCT scans were also acquired just after patient repositioning and after dose delivery. A mixed online-offline setup correction protocol (“O2 protocol”) was designed to compensate for both inter- and intrafraction motion. Results: Observed interfraction, systematic (Σ), and random (σ) setup errors in left-right (LR), craniocaudal (CC), and anteroposterior (AP) directions were 0.9, 2.0, and 1.1 mm and 1.0, 1.6, and 1.0 mm, respectively. After correction of these errors, the following intrafraction movements derived from the CBCT acquired after dose delivery were: Σ = 0.4, 1.3, and 0.7 mm, and σ = 0.8, 1.4, and 0.8 mm. More than half of the patients showed a systematic non-zero intrafraction shift in target position, (ie, the mean intrafraction displacement over the treatment fractions was statistically significantly different from zero; P<.05). With the applied CTV-PTV margins (for most patients 3, 5, and 3 mm in LR, CC, and AP directions, respectively), the minimum CTV dose, estimated from the target displacements observed in the last CBCT, was at least 94% of the prescribed dose for all patients and more than 98% for most patients (37 of 42). The proposed O2 protocol could effectively reduce the systematic intrafraction errors observed after dose delivery to almost zero (Σ = 0.1, 0.2, 0.2 mm). Conclusions: With

  13. Estimations of neutron yield from beryllium target irradiated by SPring-8 hard synchrotron radiation

    CERN Document Server

    Gryaznykh, D A; Plokhoi, V V

    2000-01-01

    The possibility of creating a neutron source based on ''SPring-8'' synchrotron radiation interaction with beryllium targets is discussed. The possible neutron yield is estimated to be of order 10 sup 1 sup 2 s sup - sup 1 .

  14. A method to achieve rapid localised deep heating in a laser irradiated solid density target

    CERN Document Server

    Schmitz, Holger

    2016-01-01

    Rapid heating of small buried regions by laser generated fast electrons may be useful for applications such as XUV radiation sources or as drivers for shock experiments. In non-structured targets the heating profile possesses a global maximum near the front surface. This paper presents a new target design that uses resistive guiding to concentrate the fast electron current density at a finite depth inside the target. The choice of geometry uses principles of non-imaging optics. A global temperature maximum at depths up to 50{\\mu}m into the target is achieved. Although theoretical calculations suggest that small source sizes should perform better than large ones, simulations show that a large angular spread at high intensities results in significant losses of the fast electrons to the sides. A systematic parameter scan suggests an optimal laser intensity. A ratio of 1.6 is demonstrated between the maximum ion temperature and the ion temperature at the front surface.

  15. Strong soft X-ray emission from a double-stream gas puff target irradiated with a nanosecond Nd:YAG laser

    Energy Technology Data Exchange (ETDEWEB)

    Fiedorowicz, H.; Bartnik, A.; Rakowski, R.; Szczurek, M. [Military Univ. of Technology, Warsaw (Poland). Inst. of Optoelectronics; Daido, H.; Suzuki, M.; Yamagami, S.; Choi, I.W.; Tang, H.J. [Osaka Univ., Suita (Japan). Inst. of Laser Engineering

    2001-07-01

    Soft X-ray emission from a new double-stream gas puff target irradiated with a nanosecond, high-power Nd:YAG laser pulse has been studied. The target was formed by pulsed injection of gas into a hollow gas stream made from helium by using a double-nozzle setup. Strong X-ray emissions near 10 nm from the double-stream krypton/helium, near 11 nm from the xenon/helium, and at 13 nm from the oxygen/helium targets were observed. The emission from the double-stream gas puff target was several times higher as compared to the ordinary gas puff targets, and comparable to the emission from the solid targets irradiated in the same conditions. (orig.)

  16. Evidence for ultra-fast heating in intense-laser irradiated reduced-mass targets

    Energy Technology Data Exchange (ETDEWEB)

    Neumayer, P.; Gumberidze, A.; Hochhaus, D. C. [ExtreMe Matter Institute EMMI and Research Division, GSI Helmholtzzentrum fuer Schwerionenforschung, 64291 Darmstadt (Germany); Frankfurt Institute for Advanced Studies FIAS, 60438 Frankfurt am Main (Germany); Aurand, B.; Stoehlker, T. [Helmholtzzentrum fuer Schwerionenforschung GSI, 64291 Darmstadt (Germany); Helmholtz Institute Jena, 07743 Jena (Germany); Costa Fraga, R. A.; Kalinin, A. [Institut fuer Kernphysik, J. W. Goethe University Frankfurt, 60438 Frankfurt am Main (Germany); Ecker, B. [Johannes Gutenberg University Mainz, 55099 Mainz (Germany); Helmholtz Institute Jena, 07743 Jena (Germany); Grisenti, R. E. [Institut fuer Kernphysik, J. W. Goethe University Frankfurt, 60438 Frankfurt am Main (Germany); Helmholtzzentrum fuer Schwerionenforschung GSI, 64291 Darmstadt (Germany); Kaluza, M. C. [Helmholtz Institute Jena, 07743 Jena (Germany); IOQ Institute of Optics and Quantum Electronics, University of Jena (Germany); Kuehl, T. [Johannes Gutenberg University Mainz, 55099 Mainz (Germany); Helmholtzzentrum fuer Schwerionenforschung GSI, 64291 Darmstadt (Germany); Helmholtz Institute Jena, 07743 Jena (Germany); Polz, J. [IOQ Institute of Optics and Quantum Electronics, University of Jena (Germany); Reuschl, R. [ExtreMe Matter Institute EMMI and Research Division, GSI Helmholtzzentrum fuer Schwerionenforschung, 64291 Darmstadt (Germany); Winters, D.; Winters, N.; Yin, Z. [Helmholtzzentrum fuer Schwerionenforschung GSI, 64291 Darmstadt (Germany)

    2012-12-15

    We report on an experiment irradiating individual argon droplets of 20 {mu}m diameter with laser pulses of several Joule energy at intensities of 10{sup 19} W/cm{sup 2}. K-shell emission spectroscopy was employed to determine the hot electron energy fraction and the time-integrated charge-state distribution. Spectral fitting indicates that bulk temperatures up to 160 eV are reached. Modelling of the hot-electron relaxation and generation of K-shell emission with collisional hot-electron stopping only is incompatible with the experimental results, and the data suggest an additional ultra-fast (sub-ps) heating contribution. For example, including resistive heating in the modelling yields a much better agreement with the observed final bulk temperature and qualitatively reproduces the observed charge state distribution.

  17. Temperature effect of irradiated target surface on distribution of nanoparticles formed by implantation

    CERN Document Server

    Stepanov, A L; Popok, V N

    2001-01-01

    The composition layers, containing the metal nanoparticles, synthesized thorough implantation of the Ag sup + ions with the energy of 60 keV and the dose of 3 x 10 sup 1 sup 6 ion/cm sup 2 into the sodium-calcium silicate glass by the ion current of 3 mu A/cm sup 2 and the sublayer temperature of 35 deg C are studied. The obtained implantation results are analyzed in dependence on the temperature effects, developing for the glass samples of various thickness. The data on the silver distribution, the metal nanoparticles formation and growth by depth are obtained from the optical reflection spectra. It is demonstrated that minor changes in the surface temperature of the irradiated glass sublayer lead to noticeable diversities in the regularities of the nanoparticles formation in the sample volume

  18. Target irradiation induced bystander effects between stem-like and non stem-like cancer cells

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Yu [State Key Laboratory of Nuclear Physics and Technology, School of Physics, Peking University, Beijing 100871 (China); Space Radiation Research Unit, International Open Laboratory, National Institute of Radiological Sciences, 4-9-1 Inage-ku, Chiba 263-8555 (Japan); Kobayashi, Alisa [Space Radiation Research Unit, International Open Laboratory, National Institute of Radiological Sciences, 4-9-1 Inage-ku, Chiba 263-8555 (Japan); Department of Technical Support and Development, National Institute of Radiological Sciences, 4-9-1 Inage-ku, Chiba 263-8555 (Japan); Maeda, Takeshi [Department of Technical Support and Development, National Institute of Radiological Sciences, 4-9-1 Inage-ku, Chiba 263-8555 (Japan); Fu, Qibin [State Key Laboratory of Nuclear Physics and Technology, School of Physics, Peking University, Beijing 100871 (China); Oikawa, Masakazu [Department of Technical Support and Development, National Institute of Radiological Sciences, 4-9-1 Inage-ku, Chiba 263-8555 (Japan); Yang, Gen, E-mail: gen.yang@pku.edu.cn [State Key Laboratory of Nuclear Physics and Technology, School of Physics, Peking University, Beijing 100871 (China); Space Radiation Research Unit, International Open Laboratory, National Institute of Radiological Sciences, 4-9-1 Inage-ku, Chiba 263-8555 (Japan); Konishi, Teruaki, E-mail: tkonishi@nirs.go.jp [Space Radiation Research Unit, International Open Laboratory, National Institute of Radiological Sciences, 4-9-1 Inage-ku, Chiba 263-8555 (Japan); Department of Technical Support and Development, National Institute of Radiological Sciences, 4-9-1 Inage-ku, Chiba 263-8555 (Japan); Uchihori, Yukio [Space Radiation Research Unit, International Open Laboratory, National Institute of Radiological Sciences, 4-9-1 Inage-ku, Chiba 263-8555 (Japan); Department of Technical Support and Development, National Institute of Radiological Sciences, 4-9-1 Inage-ku, Chiba 263-8555 (Japan); and others

    2015-03-15

    Highlights: • Existence of radiation induced bystander effects (RIBE) between cancer stem-like cells (CSCs) and non stem-like cancer cells (NSCCs) in human fibrosarcoma HT1080 cells. • Existence of significant difference in generation and response of bystander signals between CSCs and NSCCs. • CSCs are significantly less sensitive to NO scavenger than that of NSCCs in terms of DNA double strand breaks induced by RIBE. - Abstract: Tumors are heterogeneous in nature and consist of multiple cell types. Among them, cancer stem-like cells (CSCs) are suggested to be the principal cause of tumor metastasis, resistance and recurrence. Therefore, understanding the behavior of CSCs in direct and indirect irradiations is crucial for clinical radiotherapy. Here, the CSCs and their counterpart non stem-like cancer cells (NSCCs) in human HT1080 fibrosarcoma cell line were sorted and labeled, then the two cell subtypes were mixed together and chosen separately to be irradiated via a proton microbeam. The radiation-induced bystander effect (RIBE) between the CSCs and NSCCs was measured by imaging 53BP1 foci, a widely used indicator for DNA double strand break (DSB). CSCs were found to be less active than NSCCs in both the generation and the response of bystander signals. Moreover, the nitric oxide (NO) scavenger c-PTIO can effectively alleviate the bystander effect in bystander NSCCs but not in bystander CSCs, indicating a difference of the two cell subtypes in NO signal response. To our knowledge, this is the first report shedding light on the RIBE between CSCs and NSCCs, which might contribute to a further understanding of the out-of-field effect in cancer radiotherapy.

  19. Study of intense pulse irradiation effects on silicon targets considered as ground matter for optical detectors; Etude des effets d`irradiations pulsees intenses sur des cibles de silicium considere en tant que materiau de base pour detecteurs optiques

    Energy Technology Data Exchange (ETDEWEB)

    Muller, O.

    1994-12-01

    This study aim was centered on morphological and structural alterations induced by laser irradiation on silicon targets considered as ground matter for optical detectors. First we recalled the main high light intensity effects on the condensed matter. Then we presented the experimental aspects. The experimental studies were achieved on two sample types: SiO{sub 2}/Si and Si. Two topics were studied: the defect chronology according to wavelength and pulse length, and the crystalline quality as well as the structure defects of irradiated zones by Raman spectroscopy. Finally, irradiation of Si targets by intense pulsed beams may lead to material fusion. This phenomenon is particularly easy when the material is absorbent, when the pulse is short and when the material is superficially oxidized. (MML). 204 refs., 93 figs., 21 tabs., 1 appendix.

  20. Target size analysis by radiation inactivation: a large capacity tube rack for irradiation in a Gammacell 220.

    Science.gov (United States)

    Beauregard, G; Giroux, S; Potier, M

    1983-07-15

    Target size analysis by radiation inactivation is now a well-established method to study structure-function relationships in biologically active macromolecules without prior purification or even solubilization. Recently, it was reported that a relatively low-dose-rate but commonly available gamma source such as the Gammacell 220 (Atomic Energy of Canada, Ltd.) can be used to carry out radiation inactivation experiments providing it is appropriately calibrated with enzymes of known radiation sensitivities (G. Beauregard and M. Potier (1982) Anal. Biochem. 122, 379-384). In this report, a tube rack designed to fit into the irradiation chamber of the Gammacell 220 which allows five experiments (at 30 tubes per experiment) to be carried out simultaneously with both standard and unknown samples is described. The dose rates delivered at different positions in the rack were determined by irradiating rat liver cytosolic neuraminidase, an enzyme of known radiation sensitivity. A better than 2.7% agreement was obtained between experimental dose rate and computed values from isodose curves previously published by other authors (O. A. Curzio and H. O. Quaranta (1982) Int. J. Appl. Radiat. Isot. 33, 1-3).

  1. Deformation mechanisms during compressive loading of tantalum and tantalum-2.5 weight percent tungsten

    Science.gov (United States)

    Kapoor, Rajeev

    In this study it was attempted to understand the deformation behavior of tantalum and tantalum alloyed with 2.5 weight % tungsten. Uniaxial compressive deformation was carried out on polycrystalline Ta, Ta-2.5%W, and single crystal Ta. Experiments were carried out for a range of strain rates (10sp{-4}/s to 3000/s), and for a range of temperatures (77K, 296K-1000K). During high strain rate adiabatic plastic deformation of Ta-2.5%W, the energy converted to heat was directly measured using an infra-red method, and indirectly, using the recovery Hopkinson bar technique. It was concluded that within experimental error close to 100% of the work is converted to heat. During high strain rate deformation, the internal dislocation structure of both Ta and Ta-2.5%W was found to be independent of testing temperature. Thus the flow stress could be separated into two types of components, one type which are strain rate - temperature dependent and the other type which are only strain dependent. However, at lower strain rates prominent dynamic strain aging is observed and the effect of strain is coupled with the strain rate - temperature effect. At these lower strain rates, the evolution of structure does depend on the applied strain rate and temperature. When deformed at liquid nitrogen temperature, tantalum twins even at strain rates as low as 0.001/s. In the high strain rate - room temperature regime no twinning is observed. With the addition of tungsten to tantalum, the temperature and strain rate sensitivity of flow stress reduces. In addition to this, twinning is inhibited and occurs only at high strain rates - liquid nitrogen temperatures. Experiments on single crystal tantalum carried out revealed that the temperature sensitivity of flow stress on the (211) (111) slip system is similar to that on the (101) (111) slip system. Further experiments carried out on single crystal tantalum to study latent hardening did show 10% latent hardening on the \\{211\\} intersecting slip

  2. Secondary neutron production from thick Pb target by light particle irradiation

    CERN Document Server

    Adloff, J C; Debeauvais, M; Fernández, F; Krivopustov, M; Kulakov, B A; Sosnin, A; Zamani, M

    1999-01-01

    Neutron multiplicities from spallation neutron sources were measured by Solid State Nuclear Track Detectors. Light particles as protons, deuterons and alphas in the GeV range were used on Pb targets. For neutron thermalization the targets were covered by 6 cm paraffin moderator. Neutron multiplicity distributions were studied inside and on the moderator surface. Comparison of SSNTDs results were made for thermal-epithermal neutrons with sup 1 sup 3 sup 9 La activation method as well as with Dubna DCM/CEM code. Discussion including previous sup 1 sup 2 C results are given.

  3. Tantalum-based semiconductors for solar water splitting.

    Science.gov (United States)

    Zhang, Peng; Zhang, Jijie; Gong, Jinlong

    2014-07-07

    Solar energy utilization is one of the most promising solutions for the energy crises. Among all the possible means to make use of solar energy, solar water splitting is remarkable since it can accomplish the conversion of solar energy into chemical energy. The produced hydrogen is clean and sustainable which could be used in various areas. For the past decades, numerous efforts have been put into this research area with many important achievements. Improving the overall efficiency and stability of semiconductor photocatalysts are the research focuses for the solar water splitting. Tantalum-based semiconductors, including tantalum oxide, tantalate and tantalum (oxy)nitride, are among the most important photocatalysts. Tantalum oxide has the band gap energy that is suitable for the overall solar water splitting. The more negative conduction band minimum of tantalum oxide provides photogenerated electrons with higher potential for the hydrogen generation reaction. Tantalates, with tunable compositions, show high activities owning to their layered perovskite structure. (Oxy)nitrides, especially TaON and Ta3N5, have small band gaps to respond to visible-light, whereas they can still realize overall solar water splitting with the proper positions of conduction band minimum and valence band maximum. This review describes recent progress regarding the improvement of photocatalytic activities of tantalum-based semiconductors. Basic concepts and principles of solar water splitting will be discussed in the introduction section, followed by the three main categories regarding to the different types of tantalum-based semiconductors. In each category, synthetic methodologies, influencing factors on the photocatalytic activities, strategies to enhance the efficiencies of photocatalysts and morphology control of tantalum-based materials will be discussed in detail. Future directions to further explore the research area of tantalum-based semiconductors for solar water splitting

  4. Structure refinement for tantalum nitrides nanocrystals with various morphologies

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Lianyun [School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, 30 Xue Yuan Road, Haidian District, Beijing 100083 (China); School of Science, Beijing Jiaotong University, 3 Shang Yuan Cun, Haidian District, Beijing 100044 (China); Huang, Kai; Hou, Jungang [School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, 30 Xue Yuan Road, Haidian District, Beijing 100083 (China); Zhu, Hongmin, E-mail: hzhu@metall.ustb.edu.cn [School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, 30 Xue Yuan Road, Haidian District, Beijing 100083 (China)

    2012-07-15

    Graphical abstract: Tantalum nitrides nanocrystals with various phases and morphologies for the first time have been synthesized through homogenous sodium reduction under low temperature with the subsequent annealing process under high vacuum. Highlights: ► The spherical TaN, cuboidal TaN{sub 0.83} and TaN{sub 0.5} nanocrystals have been synthesized through homogenous sodium reduction under low temperature with the subsequent annealing process under high vacuum. ► The crystal structures of different tantalum nitrides were determined by Rietveld refinement on the X-ray diffraction data and the examinations of electron microcopies. ► The specific surface area of the tantalum nitrides powders was around 10 m{sup 2} g{sup −1}. ► Tantalum nitrides powders could be suitable for capacitor with high specific capacitance. -- Abstract: Tantalum nitrides (TaN{sub x}) nanocrystals with different phase and morphology have been synthesized through homogenous sodium reduction under low temperature with the subsequent annealing process under high vacuum. The crystal structures of tantalum nitrides were determined by Rietveld refinement based on the X-ray diffraction data. The morphologies of various tantalum nitrides nanocrystals in high quality were analyzed through the electron microcopies examinations. The spherical TaN nanoparticles, cuboidal TaN{sub 0.83} and TaN{sub 0.5} nanocrystals have been selectively prepared at different annealing temperatures. In addition, the specific surface areas of the tantalum nitrides nanocrystals measured by BET method were around 9.87–11.64 m{sup 2} g{sup −1}, indicating that such nano-sized tantalum nitrides could be suitable for capacitor with high specific capacitance.

  5. Twinning anisotropy of tantalum during nanoindentation

    Energy Technology Data Exchange (ETDEWEB)

    Goel, Saurav, E-mail: S.GOEL@qub.ac.uk [School of Mechanical and Aerospace Engineering, Queen' s University, Belfast, BT9 5AH (United Kingdom); Beake, Ben [Micro Materials Limited, Willow House, Yale Business Village, Ellice Way, Wrexham LL13 7YL (United Kingdom); Dalton Research Institute, Manchester Metropolitan University, Manchester, M15GD (United Kingdom); Chan, Chi-Wai [School of Mechanical and Aerospace Engineering, Queen' s University, Belfast, BT9 5AH (United Kingdom); Haque Faisal, Nadimul [School of Engineering, Robert Gordon University, Garthdee Road, Aberdeen AB10 7GJ (United Kingdom); Dunne, Nicholas [School of Mechanical and Aerospace Engineering, Queen' s University, Belfast, BT9 5AH (United Kingdom)

    2015-03-11

    Unlike other BCC metals, the plastic deformation of nanocrystalline Tantalum (Ta) during compression is regulated by deformation twinning. Whether or not this twinning exhibits anisotropy was investigated through simulation of displacement-controlled nanoindentation test using molecular dynamics (MD) simulation. MD data was found to correlate well with the experimental data in terms of surface topography and hardness measurements. The mechanism of the transport of material was identified due to the formation and motion of prismatic dislocations loops (edge dislocations) belonging to the 1/2〈111〉 type and 〈100〉 type Burgers vector family. Further analysis of crystal defects using a fully automated dislocation extraction algorithm (DXA) illuminated formation and migration of twin boundaries on the (110) and (111) orientation but not on the (010) orientation and most importantly after retraction all the dislocations disappeared on the (110) orientation suggesting twinning to dominate dislocation nucleation in driving plasticity in tantalum. A significant finding was that the maximum shear stress (critical Tresca stress) in the deformation zone exceeded the theoretical shear strength of Ta (Shear modulus/2π~10.03 GPa) on the (010) orientation but was lower than it on the (110) and the (111) orientations. In light of this, the conventional lore of assuming the maximum shear stress being 0.465 times the mean contact pressure was found to break down at atomic scale.

  6. Evaluation of Polymer Hermetically Sealed Tantalum Capacitors

    Science.gov (United States)

    Teverovsky, Alexander A.

    2014-01-01

    Polymer cathode tantalum capacitors have lower ESR (equivalent series resistance) compared to other types of tantalum capacitors and for this reason have gained popularity in the electronics design community. Their use allows improved performance of power supply systems along with substantial reduction of size and weight of the components used. However, these parts have poor thermal stability and can degrade in humid environments. Polymer hermetically sealed (PHS) capacitors avoid problems related to environmental degradation of molded case parts and can potentially replace current wet and solid hermetically sealed capacitors. In this work, PHS capacitors manufactured per DLA LAM DWG#13030 are evaluated for space applications. Several lots of capacitors manufactured over period from 2010 to 2014 were tested for the consistency of performance, electrical and thermal characteristics, highly accelerated life testing, and robustness under reverse bias and random vibration conditions. Special attention was given to analysis of leakage currents and the effect of long-term high temperature storage on capacitors in as is condition and after hermeticity loss. The results show that PHS capacitors might be especially effective for low-temperature applications or for system requiring a cold start-up. Additional screening and qualification testing have been recommended to assure the necessary quality of capacitors for space projects.

  7. Production of isotopes and isomers with irradiation of Z = 47–50 targets by 23-MeV bremsstrahlung

    Energy Technology Data Exchange (ETDEWEB)

    Karamian, S. A., E-mail: karamian@nrmail.jinr.ru [Joint Institute for Nuclear Research (Russian Federation); Carroll, J. J. [US Army Research Laboratory (United States); Aksenov, N. V.; Albin, Yu. A.; Belov, A. G.; Bozhikov, G. A.; Dmitriev, S. N.; Starodub, G. Ya. [Joint Institute for Nuclear Research (Russian Federation)

    2015-09-15

    The irradiations of Ag to Sn targets by bremsstrahlung generated with 23-MeV electron beams are performed at the MT-25 microtron. Gamma spectra of the induced activities have been measured and the yields of all detected radionuclides and isomers are carefully measured and analyzed. A regular dependence of yields versus changed reaction threshold is confirmed. Many isomers are detected and the suppression of the production probability is observed with growing product spin. Special peculiarities for the isomer-to-ground state ratios were deduced for the {sup 106m}Ag, {sup 108m}Ag, {sup 113m}In, {sup 115m}In, and {sup 123m}Sn isomers. The production of such nuclides as {sup 108m}Ag, {sup 115m}In, {sup 117g}In, and {sup 113m}Cd is of interest for applications, especially when economic methods are available.

  8. FY-15 Progress Report on Cleanup of irradiated SHINE Target Solutions Containing 140g-U/L Uranyl Sulfate

    Energy Technology Data Exchange (ETDEWEB)

    Bennett, Megan E. [Argonne National Lab. (ANL), Argonne, IL (United States); Bowers, Delbert L. [Argonne National Lab. (ANL), Argonne, IL (United States); Vandegrift, George F. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2015-09-01

    During FY 2012 and 2013, a process was developed to convert the SHINE Target Solution (STS) of irradiated uranyl sulfate (140 g U/L) to uranyl nitrate. This process is necessary so that the uranium solution can be processed by the UREX (Uranium Extraction) separation process, which will remove impurities from the uranium so that it can be recycled. The uranyl sulfate solution must contain <0.02 M SO42- so that the uranium will be extractable into the UREXsolvent. In addition, it is desired that the barium content be below 0.0007 M, as this is the limit in the Resource Conservation and Recovery Act (RCRA).

  9. Suprathermal electron production in laser-irradiated Cu targets characterized by combined methods of x-ray imaging and spectroscopy

    Science.gov (United States)

    Renner, O.; Šmíd, M.; Batani, D.; Antonelli, L.

    2016-07-01

    In a series of experiments performed with laser-irradiated planar targets at the PALS laser facility, the generation of suprathermal electrons has been studied at conditions relevant for the development of a shock ignition approach to inertial confinement fusion. A simultaneous application of high-collection-efficiency K-shell imaging with high resolution x-ray spectroscopy offers a novel approach to hot electron diagnosis at non-coated or moderately coated, medium-atomic-number targets, where the contribution of suprathermal-electron-generated, frequency-shifted Kα emission from highly ionized atoms cannot be neglected. Based on experimental data provided by these combined techniques and their interpretation via collisional-radiative atomic codes and Monte Carlo modeling of hot electron energy deposition in heated Cu targets, the fraction of the energy converted to hot electrons at laser intensities  ≈1016 W cm-2 was measured to be at the level of 0.1-0.8%. The higher values of conversion efficiency found for frequency tripled radiation support a theoretical conjecture of enhanced laser energy absorption by a resonance mechanism and its transport to a flow of fast electrons.

  10. Prediction of production of 22Na in a gas-cell target irradiated by protons using Monte Carlo tracking

    Science.gov (United States)

    Eslami, M.; Kakavand, T.; Mirzaii, M.; Rajabifar, S.

    2015-01-01

    The 22Ne(p,n)22Na is an optimal reaction for the cyclotron production of 22Na. This work tends to monitor the proton induced production of 22Na in a gas-cell target, containing natural and enriched neon gas, using Monte Carlo method. The excitation functions of reactions are calculated by both TALYS-1.6 and ALICE/ASH codes and then the optimum energy range of projectile for the high yield production is selected. A free gaseous environment of neon at a particular pressure and temperature is prearranged and the proton beam is transported within it using Monte Carlo codes MCNPX and SRIM. The beam monitoring performed by each of these codes indicates that the gas-cell has to be designed as conical frustum to reach desired interactions. The MCNPX is also employed to calculate the energy distribution of proton in the designed target and estimation of the residual nuclei during irradiation. The production yield of 22Na in 22Ne(p,n)22Na and natNe(p,x)22Na reactions are estimated and it shows a good agreement with the experimental results. The results demonstrate that Monte Carlo makes available a beneficial manner to design and optimize the gas targets as well as calibration of detectors, which can be used for the radionuclide production purposes.

  11. In-target electron thermalization by the Weibel instability during intense irradiation of a thin aluminum foil

    Science.gov (United States)

    Fuchs, J.; Ruyer, C.; Albertazzi, B.; Lancia, L.; Dervieux, V.; Antici, P.; Bocker, J.; Chen, S. N.; Nakatsutsumi, M.; Romagnani, L.; Shepherd, R.; Swantusch, M.; Borghesi, M.; Willi, O.; Pepin, H.; Grech, M.; Riconda, C.; Gremillet, L.

    2015-11-01

    Proton-radiography of the electromagnetic fields developing after irradiation of a 3 μm-thick Al foil by a high-intensity laser (5 ×1019 W.cm-2, 700fs, 8 μm focal spot) was performed at the Titan facility. The obtained radiographs evidence filamentary structures which develop inside the dense target, 300 μ m away from the focal spot, a few picoseconds after the laser drive. We will demonstrate that the radiographs' structures are due to magnetic fields triggered by the so-called Weibel instability, inside the dense target. For this purpose, large scale particle-in-cell simulations of hot electrons thermalization in a dense, cold and collisional target have been performed. They demonstrate the ability of the laser-heated electrons to sustain a strong temperature anisotropy during their relaxation in the thin foil. This hot electron anisotropy results in a Weibel instability, thus triggering magnetic fluctuations of spectrum consistent with the experiment over 10 picoseconds.

  12. Target irradiation facility and targetry development at 160 MeV proton beam of Moscow linac

    CERN Document Server

    Zhuikov, B L; Konyakhin, N A; Vincent, J

    1999-01-01

    A facility has been built and successfully operated with the 160 MeV proton beam of Moscow Meson factory LINAC, Institute for Nuclear Research (INR) of Russian Academy of Science, Troitsk. The facility was created for various isotope production goals as well as for fundamental nuclear investigations at high intensity beam (100 mu A and more). An important part of the facility targetry system is a high-intensity beam monitoring collimator device. Measurements of the temperature distribution between collimator sectors, cooling water flow and temperature, and the beam current, provide an opportunity to compute beam losses and beam position. The target holder design allows easy insertion by manipulator and simultaneous bombardment of several different targets of various types and forms, and variation of proton energy on each target over a wide range below 160 MeV. The main target utilized for commercial sup 8 sup 2 Sr isotope production is metallic rubidium in a stainless-steel container. A regular wet chemistry ...

  13. 2017 NEPP Tasks Update for Ceramic and Tantalum Capacitors

    Science.gov (United States)

    Teverovsky, Alexander A.

    2017-01-01

    This presentation gives an overview of current NEPP tasks on ceramic and tantalum capacitors and plans for the future. It includes tasks on leakage currents, gas generation and case deformation in wet tantalum capacitors; ESR degradation and acceleration factors in MnO2 and polymer cathode capacitors. Preliminary results on the effect of moisture on degradation of reverse currents in MnO2 tantalum capacitors are discussed. Latest results on mechanical characteristics of MLCCs and modeling of degradation of leakage currents in BME capacitors with defects are also presented.

  14. Waste Treatment of Acidic Solutions from the Dissolution of Irradiated LEU Targets for 99-Mo Production

    Energy Technology Data Exchange (ETDEWEB)

    Bakel, Allen J. [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Conner, Cliff [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Quigley, Kevin [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Vandegrift, George F. [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division

    2016-10-01

    One of the missions of the Reduced Enrichment for Research and Test Reactors (RERTR) program (and now the National Nuclear Security Administrations Material Management and Minimization program) is to facilitate the use of low enriched uranium (LEU) targets for 99Mo production. The conversion from highly enriched uranium (HEU) to LEU targets will require five to six times more uranium to produce an equivalent amount of 99Mo. The work discussed here addresses the technical challenges encountered in the treatment of uranyl nitrate hexahydrate (UNH)/nitric acid solutions remaining after the dissolution of LEU targets. Specifically, the focus of this work is the calcination of the uranium waste from 99Mo production using LEU foil targets and the Modified Cintichem Process. Work with our calciner system showed that high furnace temperature, a large vent tube, and a mechanical shield are beneficial for calciner operation. One- and two-step direct calcination processes were evaluated. The high-temperature one-step process led to contamination of the calciner system. The two-step direct calcination process operated stably and resulted in a relatively large amount of material in the calciner cup. Chemically assisted calcination using peroxide was rejected for further work due to the difficulty in handling the products. Chemically assisted calcination using formic acid was rejected due to unstable operation. Chemically assisted calcination using oxalic acid was recommended, although a better understanding of its chemistry is needed. Overall, this work showed that the two-step direct calcination and the in-cup oxalic acid processes are the best approaches for the treatment of the UNH/nitric acid waste solutions remaining from dissolution of LEU targets for 99Mo production.

  15. Conversion of Molybdenum-99 production process to low enriched uranium: Neutronic and thermal hydraulic analyses of HEU and LEU target plates for irradiation in Pakistan Research Reactor-1

    Science.gov (United States)

    Mushtaq, Ahmad; Iqbal, Masood; Bokhari, Ishtiaq Hussain; Mahmood, Tayyab; Muhammad, Atta

    2012-09-01

    Technetium-99m, the daughter product of Molybdenum-99 is the most widely needed radionuclide for diagnostic studies in Pakistan. Molybdenum-99 Production Facility has been established at PINSTECH. Highly enriched uranium (93% 235U) U/Al alloy targets have been irradiated in Pakistan Research Reactor-1 (PARR-1) for the generation of fission Mo-99, while basic dissolution technique is used for separation of Mo-99 from target matrix activity. In line with the international objective of minimizing and eventually eliminating the use of HEU in civil commerce, national and international efforts have been underway to shift the production of medical isotopes from HEU to LEU (LEU; uranium is needed. LEU aluminum uranium dispersion target has been developed, which may replace existing HEU aluminum/uranium alloy targets for production of 99Mo using basic dissolution technique. Neutronic and thermal hydraulic calculations were performed for safe irradiation of targets in the core of PARR-1.

  16. Targeted bone marrow irradiation in the conditioning of high-risk leukaemia prior to stem cell transplantation

    Energy Technology Data Exchange (ETDEWEB)

    Reske, S.N.; Buchmann, I.; Seitz, U.; Glatting, G.; Neumaier, B.; Kotzerke, J.; Buck, A. [Ulm Univ. (Germany). Abt. Nuklearmedizin; Bunjes, D.; Doehner, H. [Abteilung Innere Medizin III, Haematologie und Onkologie, Universitaetsklinikum Ulm (Germany); Martin, H.; Bergmann, L. [Klinik fuer Haematologie und Onkologie, Johann-Wolfgang-Goethe Universitaet Frankfurt (Germany)

    2001-07-01

    Disease recurrence following stem cell transplantation (SCT) remains a major problem. Despite the sensitivity of leukaemias to chemotherapy and irradiation, conventional conditioning before SCT is limited by significant organ toxicity. Targeted irradiation of bone marrow and spleen by radioimmunotherapy may provide considerable dose escalation, with limited toxicity to non-target organs. In this study, 27 patients with high-risk or relapsing leukaemia were treated with rhenium-188-labelled CD66a,b,c,e radioimmunoconjugates ({sup 188}Re-mAb) specific for normal bone marrow in addition to conventional conditioning with high-dose chemotherapy and 12 Gy total body irradiation prior to SCT. A mean activity of 10.2{+-}2.1 (range 6.9-15.8) GBq {sup 188}Re-mAb was administered intravenously. Acute side-effects were assessed according to the CTC classification and patient outcome was determined. Mean radiation doses (Gy; range in parentheses) to relevant organs and whole body were as follows: 13.1 (6.5-22) to bone marrow, 11.6 (1.7-31.1) to spleen, 5.0 (2.0-11.7) to liver, 7.0 (2.3-11.6) to kidneys, 0.7 (0.3-1.3) to lungs and 1.4 (0.8-2.1) to the whole body. Stem cells engrafted in all patients within 9-18 days post SCT. Acute organ toxicity of grade II or less was observed. During follow-up for 25.4{+-}5.3 (range 18-34) months, 4/27 (15%) patients died from relapse, and 9/27 (33%) from transplantation-related complications. Fourteen patients (52%) are still alive and in ongoing complete clinical remission. Radioimmunotherapy with the bone marrow-seeking {sup 188}Re-labelled CD66 mAb can double the dose to bone marrow and spleen without undue extramedullary acute organ toxicity, when given in addition to high-dose chemotherapy and 12 Gy TBI before allogeneic SCT. This intensified conditioning regimen may reduce the relapse rate of high-risk leukaemia. (orig.)

  17. A quantitative and comparative study of radionuclidic and chemical impurities in water samples irradiated in a niobium target with Havar vs. niobium-sputtered Havar as entrance foils

    Energy Technology Data Exchange (ETDEWEB)

    Avila-Rodriguez, Miguel A. [Edmonton PET Centre, Cross Cancer Institute, Alberta Cancer Board, 11560 University Avenue, Edmonton, AB, T6G 1Z2 (Canada)], E-mail: Miguel.Avila-Rodriguez@utu.fi; Wilson, John S.; McQuarrie, Steve A. [Edmonton PET Centre, Cross Cancer Institute, Alberta Cancer Board, 11560 University Avenue, Edmonton, AB, T6G 1Z2 (Canada)

    2008-12-15

    Enriched and natural abundance water samples were irradiated in a niobium (Nb) chamber target with Havar and Nb-sputtered Havar foils. Irradiations were performed with 17.5 MeV protons at currents from 35 to 100 {mu}A lasting for 1-2.5 h. Radionuclidic and chemical (cationic) impurities were determined via gamma spectroscopy and ICP-MS, respectively. Anionic impurities were evaluated by ion chromatography. Impurities in water samples irradiated with the Havar-Nb foils were much lower than the samples irradiated with an unmodified Havar foil. No significant differences were observed in the impurity levels between samples of H{sub 2}{sup 18}O-enriched and natural abundance water. Radionuclidic impurities were observed to decrease after 3-4 irradiations on a fresh Havar entrance foil, and reached a constant value for subsequent irradiations with the same integrated current. For targets covered with Havar foil, radionuclidic impurities were found to be proportional to the beam-integrated current regardless of the beam power and, unexpectedly, dependant of the beam power when using a Havar-Nb foil.

  18. A quantitative and comparative study of radionuclidic and chemical impurities in water samples irradiated in a niobium target with Havar vs. niobium-sputtered Havar as entrance foils.

    Science.gov (United States)

    Avila-Rodriguez, Miguel A; Wilson, John S; McQuarrie, Steve A

    2008-12-01

    Enriched and natural abundance water samples were irradiated in a niobium (Nb) chamber target with Havar and Nb-sputtered Havar foils. Irradiations were performed with 17.5MeV protons at currents from 35 to 100microA lasting for 1-2.5h. Radionuclidic and chemical (cationic) impurities were determined via gamma spectroscopy and ICP-MS, respectively. Anionic impurities were evaluated by ion chromatography. Impurities in water samples irradiated with the Havar-Nb foils were much lower than the samples irradiated with an unmodified Havar foil. No significant differences were observed in the impurity levels between samples of H(2)(18)O-enriched and natural abundance water. Radionuclidic impurities were observed to decrease after 3-4 irradiations on a fresh Havar entrance foil, and reached a constant value for subsequent irradiations with the same integrated current. For targets covered with Havar foil, radionuclidic impurities were found to be proportional to the beam-integrated current regardless of the beam power and, unexpectedly, dependant of the beam power when using a Havar-Nb foil.

  19. Prediction of production of {sup 22}Na in a gas-cell target irradiated by protons using Monte Carlo tracking

    Energy Technology Data Exchange (ETDEWEB)

    Eslami, M., E-mail: mohammad.eslami25@yahoo.com [Department of Physics, Faculty of Science, University of Zanjan, Zengan (Zanjan) (Iran, Islamic Republic of); Kakavand, T. [Department of Physics, Faculty of Science, University of Zanjan, Zengan (Zanjan) (Iran, Islamic Republic of); Department of Physics, Faculty of Science, Imam Khomeini International University, Qazvin (Iran, Islamic Republic of); Mirzaii, M.; Rajabifar, S. [Agricultural, Medical and Industrial Research School, Nuclear Science and Technology Research Institute, AEOI, Karaj (Iran, Islamic Republic of)

    2015-01-01

    Highlights: • Angular distribution of the proton beam in a gaseous environment. • Particle energy distribution profile and proton flux within gas-cell target with MCNPX. • Detection of the residual nuclei during the nuclear reactions. • Estimation of production yield for {sup 22,nat}Ne(p,x){sup 22}Na reactions. - Abstract: The {sup 22}Ne(p,n){sup 22}Na is an optimal reaction for the cyclotron production of {sup 22}Na. This work tends to monitor the proton induced production of {sup 22}Na in a gas-cell target, containing natural and enriched neon gas, using Monte Carlo method. The excitation functions of reactions are calculated by both TALYS-1.6 and ALICE/ASH codes and then the optimum energy range of projectile for the high yield production is selected. A free gaseous environment of neon at a particular pressure and temperature is prearranged and the proton beam is transported within it using Monte Carlo codes MCNPX and SRIM. The beam monitoring performed by each of these codes indicates that the gas-cell has to be designed as conical frustum to reach desired interactions. The MCNPX is also employed to calculate the energy distribution of proton in the designed target and estimation of the residual nuclei during irradiation. The production yield of {sup 22}Na in {sup 22}Ne(p,n){sup 22}Na and {sup nat}Ne(p,x){sup 22}Na reactions are estimated and it shows a good agreement with the experimental results. The results demonstrate that Monte Carlo makes available a beneficial manner to design and optimize the gas targets as well as calibration of detectors, which can be used for the radionuclide production purposes.

  20. Scattered light diagnostics of overdense plasma cavity in solid targets irradiated by an ultraintense laser pulse.

    Science.gov (United States)

    Andreev, A A; Zhidkov, A G; Uesaka, M; Kinoshita, K; Platonov, K Yu

    2002-09-01

    The light scattered backward from a target illuminated by ultraintense laser pulses carries important information about the nonlinear laser-plasma interaction. We analyze the usefulness of this information by plasma corona analysis with the help of an analytical model we developed, and particle-in-cell simulation. The spectrum of scattered light is shown to be shifted, to be broadened, and to be modulated, in comparison with the initial laser spectrum, and the spectral shift is an indicator of laser pulse contrast ratio.

  1. PREPARATION OF TANTALUM CARBIDE FROM AN ORGANOMETALLIC PRECURSOR

    Directory of Open Access Journals (Sweden)

    C. P. SOUZA

    1999-03-01

    Full Text Available In this work we have synthesized an organometallic oxalic precursor from tantalum oxide. This oxide was solubilized by heating with potassium hydrogen sulfate. In order to precipitate Ta2O5.nH2O, the fused mass obtained was dissolved in a sulfuric acid solution and neutralized with ammonia. The hydrated tantalum oxide precipitated was dissolved in an equimolar solution of oxalic acid/ammonium oxalate. The synthesis and the characterization of the tantalum oxalic precursor are described. Pyrolysis of the complex in a mixture of hydrogen and methane at atmospheric pressure was studied. The gas-solid reaction made it possible to obtain tantalum carbide, TaC, in the powder form at 1000oC. The natural sintering of TaC powder in an inert atmosphere at 1400°C during 10 hours, under inert atmosphere made it possible to densify the carbide to 96% of the theoretical value.

  2. Tantalum oxide thin films as protective coatings for sensors

    DEFF Research Database (Denmark)

    Christensen, Carsten; Reus, Roger De; Bouwstra, Siebe

    1999-01-01

    Reactively sputtered tantalum oxide thin-films have been investigated as protective coating for aggressive media exposed sensors. Tantalum oxide is shown to be chemically very robust. The etch rate in aqueous potassium hydroxide with pH 11 at 140°C is lower than 0.008 Å/h. Etching in liquids with p...... the residual thin-film stress can be altered from compressive to tensile and annealing at 450°C for 30 minutes gives a stress-free film. The step coverage of the sputter deposited amorphous tantalum oxide is reasonable, but metallisation lines are hard to cover. Sputtered tantalum oxide exhibits high...... dielectric strength and the pinhole density for 0.5 μm thick films is below 3 cm-2...

  3. Preparation of tantalum carbide from an organometallic precursor

    Energy Technology Data Exchange (ETDEWEB)

    Souza, C.P. [Rio Grande do Norte Univ., Natal, RN (Brazil). Programa de Pos-graduacao em Geoquimica. Lab. de Termodinamica e Reatores]. E-mail: carlson at ufrnet.ufrn.br; Favotto, C.; Satre, P.; L' Honore, A.; Roubin, M. [Universite du Toulon et de Var B.P. (France). Equipe der Materiaux a Finalite Specifique. Lab. de Physicochimie du Materiaux et du Milieu Marin]. E-mail: roubin at univ-tln.fr

    1999-03-01

    In this work we have synthesized an organometallic oxalic precursor from tantalum oxide. This oxide was solubilized by heating with potassium hydrogen sulfate. In order to precipitate Ta{sub 2} O{sub 5} nH{sub 2}O, the fused mass obtained was dissolved in a sulfuric acid solution and neutralized with ammonia. The hydrated tantalum oxide precipitated was dissolved in an equimolar solution of oxalic acid/ammonium oxalate. The synthesis and the characterization of the tantalum oxalic precursor are described. Pyrolysis of the complex in a mixture of hydrogen and methane at atmospheric pressure was studied. The gas-solid reaction made it possible to obtain tantalum carbide, Ta C, in the powder form at 1000 deg C. The natural sintering of Ta C powder in an inert atmosphere at 1400 deg C during 10 hours, under inert atmosphere made it possible to density the carbide to 96% of the theoretical value. (author)

  4. The Chemical Vapour Deposition of Tantalum - in long narrow channels

    DEFF Research Database (Denmark)

    Mugabi, James Atwoki

    use as a construction material for process equipment, with the cheaper alternative being the construction of equipment from steel and then protecting it with a thin but efficacious layer of tantalum. Chemical Vapour Deposition (CVD) is chosen as the most effective process to apply thin corrosion...... protective layers of tantalum because of the process’ ability to coat complex geometries and its relative ease to control. This work focuses on studying the CVD of tantalum in long narrow channels with the view that the knowledge gained during the project can be used to optimise the commercial coating...... process that Tantaline A/S and Alfa Laval (Sweden) use to manufacture tantalum coated plate heat exchangers. Experiments are done by coating the inner side of long, thin stainless steel tubes in the temperature range of 700 – 950 °C and pressure range of 25 – 990 mbar while using different reactant...

  5. Valence electronic structure of tantalum carbide and nitride

    Institute of Scientific and Technical Information of China (English)

    FAN; ChangZeng

    2007-01-01

    The valence electronic structures of tantalum carbide (TaC) and tantalum nitride (TaN) are studied by using the empirical electronic theory (EET). The results reveal that the bonds of these compounds have covalent, metallic and ionic characters. For a quantitative analysis of the relative strength of these components, their ionicities have been calculated by implanting the results of EET to the PVL model. It has been found that the ionicity of tantalum carbide is smaller than that of tantalum nitride. The EET results also reveal that the covalent electronic number of the strongest bond in the former is larger than that of the latter. All these suggest that the covalent bond of TaC is stronger than that of TaN, which coincides to that deduced from the first-principles method.……

  6. Valence electronic structure of tantalum carbide and nitride

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    @@ The valence electronic structures of tantalum carbide (TaC) and tantalum nitride (TaN) are studied by using the empirical electronic theory (EET). The results reveal that the bonds of these compounds have covalent, metallic and ionic characters. For a quantitative analysis of the relative strength of these components, their ionicities have been calculated by implanting the results of EET to the PVL model. It has been found that the ionicity of tantalum carbide is smaller than that of tantalum nitride. The EET results also reveal that the covalent electronic number of the strongest bond in the former is larger than that of the latter. All these suggest that the covalent bond of TaC is stronger than that of TaN, which coincides to that deduced from the first-principles method.

  7. Tantalum cones and bone defects in revision total knee arthroplasty.

    Science.gov (United States)

    Boureau, F; Putman, S; Arnould, A; Dereudre, G; Migaud, H; Pasquier, G

    2015-04-01

    Management of bone loss is a major challenge in revision total knee arthroplasty (TKA). The development of preformed porous tantalum cones offers new possibilities, because they seem to have biological and mechanical qualities that facilitate osseointegration. Compared to the original procedure, when metaphyseal bone defects are too severe, a single tantalum cone may not be enough and we have developed a technique that could extend the indications for this cone in these cases. We used 2 cones to fill femoral bone defects in 7 patients. There were no complications due to wear of the tantalum cones. Radiological follow-up did show any migration or loosening. The short-term results confirm the interest of porous tantalum cones and suggest that they can be an alternative to allografts or megaprostheses in case of massive bone defects.

  8. Production of krypton and xenon isotopes in thick stony and iron targets isotropically irradiated with 1600 MeV protons

    CERN Document Server

    Gilabert, E; Lavielle, B; Leya, I; Michel, R; Neumann, S

    2002-01-01

    Two spherical targets made of gabbro with a radius of 25 cm and of steel with a radius of 10 cm were irradiated isotropically with 1600 MeV protons at the SATURNE synchrotron at Laboratoire National Saturne (LNS)/CEN Saclay, in order to simulate the production of nuclides in meteorites induced by galactic cosmic-ray protons in space. These experiments supply depth-dependent production rate data for a wide range of radioactive and stable isotopes in up to 28 target elements. In this paper, we report results for /sup 78/Kr, /sup 80-86/Kr isotopes in Rb, Sr, Y and Zr and for /sup 124/Xe, /sup 126/Xe, /sup 128-132/Xe, /sup 134/Xe, /sup 136/Xe isotopes in Ba and La. Krypton and xenon concentrations have been measured at different depths in the spheres by using conventional mass spectrometry. Based on Monte-Carlo techniques, theoretical production rates are calculated by folding depth-dependent spectra of primary and secondary protons and secondary neutrons with the excitation functions of the relevant nuclear reac...

  9. Tantalum recycling from waste of electrical and electronic equipment

    Directory of Open Access Journals (Sweden)

    Piotrowicz Andrzej

    2016-01-01

    Full Text Available The possibility of tantalum recycling from waste of electrical and electronic equipment was investigated. Study was carried out using basic physical and chemical methods, ie. mechanical separation via crushing, leaching of silver layer in diluted HNO3, grinding and oxidation of anodes and thermic reduction with metallic reducing agent. A recovery rate of anodes was determined at 96%, and recycling efficiency of tantalum to pure form was determined more than 50%. Also was made mass balance.

  10. Corrosion behavior of tantalum and its nitride in alkali solution

    Institute of Scientific and Technical Information of China (English)

    ZHANG Deyuan; LIN Qin; FEI Qinyong; ZHAO Haomin; KANG Guangyu; GENG Man

    2003-01-01

    The corrosion behavior of tantalum and its nitrides in stirring NaOH solutions was researched by potenfiostatic method, cyclic voltammetry and XPS. The results showed that the corrosion products were composed of Ta2O5 and NaTaO3.The corrosion reaction formula of tantalum and its nitrides was written according to cyclic volt-ampere curves. The electric charge transfer coefficient and the electric charge transfer number were calculated.

  11. Forward modeling of shock-ramped tantalum

    Science.gov (United States)

    Brown, Justin L.; Carpenter, John H.; Seagle, Christopher T.

    2017-01-01

    Dynamic materials experiments on the Z-machine are beginning to reach a regime where traditional analysis techniques break down. Time dependent phenomena such as strength and phase transition kinetics often make the data obtained in these experiments difficult to interpret. We present an inverse analysis methodology to infer the equation of state (EOS) from velocimetry data in these types of experiments, building on recent advances in the propagation of uncertain EOS information through a hydrocode simulation. An example is given for a shock-ramp experiment in which tantalum was shock compressed to 40 GPa followed by a ramp to 80 GPa. The results are found to be consistent with isothermal compression and Hugoniot data in this regime.

  12. Tantalum Sheet for Superconductor Diffusion Barrier Applications

    Science.gov (United States)

    Mathaudhu, S. N.; Hartwig, K. T.; Barber, R. E.; Pyon, T.

    2006-03-01

    This report presents preliminary results of a project with the aim to fabricate fine-grained tantalum sheet having a uniform microstructure that co-deforms well with pure copper for superconductor diffusion barrier applications. Multi-pass equal channel angular extrusion (ECAE) was used to refine the microstructure of 25 mm square cross-section bars of Ta; rolling was used to convert the bars to 0.38 mm thick sheet. Cu-Ta co-deformation characteristics were evaluated by assembling and drawing experimental Cu-Ta composite wires, containing the ECAE processed sheets, to 0.83 mm diameter and metallographically examining the thinned 2-4 micron Ta layer. The ECAE processed Ta sheet co-deformed well with Cu, and was found to have a smaller recrystallized grain size, a narrower grain size distribution and a slightly higher hardness compared to commercial diffusion barrier grade Ta sheet. The favorable results encourage further work.

  13. Characterization of Tri-lab Tantalum Plate.

    Energy Technology Data Exchange (ETDEWEB)

    Buchheit, Thomas E.; Cerreta, Ellen K.; Deibler, Lisa Anne; Chen, Shu-Rong; Michael, Joseph R.

    2014-09-01

    This report provides a detailed characterization Tri-lab Tantalum (Ta) plate jointly purchased from HCStark Inc. by Sandia, Los Alamos and Lawrence Livermore National Laboratories. Data in this report was compiled from series of material and properties characterization experiments carried out at Sandia (SNL) and Los Alamos (LANL) Laboratories through a leveraged effort funded by the C2 campaign. Results include microstructure characterization detailing the crystallographic texture of the material and an increase in grain size near the end of the rolled plate. Mechanical properties evaluations include, compression cylinder, sub-scale tension specimen, micohardness and instrumented indentation testing. The plate was found to have vastly superior uniformity when compare with previously characterized wrought Ta material. Small but measurable variations in microstructure and properties were noted at the end, and at the top and bottom edges of the plate.

  14. HDR monotherapy for prostate cancer: A simulation study to determine the effect of catheter displacement on target coverage and normal tissue irradiation

    NARCIS (Netherlands)

    I.-K.K. Kolkman-Deurloo (Inger-Karina); M.A. Roos (Martin); S. Aluwini (Shafak)

    2011-01-01

    textabstractPurpose: The aim of this study was to systematically analyse the effect of catheter displacements both on target coverage and normal tissue irradiation in fractionated high dose rate (HDR) prostate brachytherapy, using a simulation study, and to define tolerances for catheter displacemen

  15. Stopping power of C, O and Cl in tantalum oxide

    Energy Technology Data Exchange (ETDEWEB)

    Barradas, Nuno P., E-mail: nunoni@ctn.ist.utl.pt [Centro de Ciências e Tecnologias Nucleares, Instituto Superior Técnico, Universidade de Lisboa, Estrada Nacional 10, ao km 139.7, 2695-066 Bobadela LRS (Portugal); Laboratório de Engenharia Nuclear, Instituto Superior Técnico, Universidade de Lisboa, Estrada Nacional 10, ao km 139.7, 2695-066 Bobadela LRS (Portugal); Alves, E. [Associação Euratom/IST, Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade Técnica de Lisboa, Av. Rovisco Pais, Lisboa 1049-001 (Portugal); Fonseca, M. [Dep. Física, Faculdade de Ciências e Tecnologia, Universidade Nova de Lisboa, 2829- 516 Caparica (Portugal); ISLA Campus Lisboa| Laureate International Universities, 1500-210 Lisboa (Portugal); Siketić, Z.; Bogdanović Radović, I. [Ruđer Bošković Institute, P.O. Box 180, 10002 Zagreb (Croatia)

    2014-08-01

    Highlights: •We measured the stopping power of C, O, and Cl in tantalum oxide. •A bulk sample method was used, with Bayesian inference data analysis. •Good agreement was found with SRIM2012 calculations. -- Abstract: Tantalum oxide is used in a variety of applications due to its high bandgap, high-K and high index of refraction. Unintentional impurities can change properties of tantalum oxide, and heavy ion elastic recoil detection is a method that can play a fundamental role in the quantification of those impurities. Furthermore, tantalum oxide is frequently part of the samples that also include other materials, which are often analysed with ion beam techniques. However, there are very few reported stopping power measurements for tantalum oxide, and data analysis relies not only on interpolation from a sparse data base but also on the Bragg rule. As is well known, the Bragg rule is often inaccurate for oxides, particularly when the difference in atomic numbers of the involved elements is very large as is case for Ta{sub 2}O{sub 5}. We have used a bulk method, previously developed by us and applied successfully to other systems, to determine experimentally the stopping power of tantalum oxide for three different ion types: C, O and Cl. In the present paper the results of our measurements and bulk method analysis are presented.

  16. Thin tantalum-silicon-oxygen/tantalum-silicon-nitrogen films as high-efficiency humidity diffusion barriers for solar cell encapsulation

    Energy Technology Data Exchange (ETDEWEB)

    Heuer, H. [Institut fuer Halbleiter-und Mikrosystemtechnik (IHM) Technische Universitaet Dresden, Helmholtzstrasse 10, 01062 Dresden (Germany)]. E-mail: Henning.Heuer@izfp-d.fraunhofer.de; Wenzel, C. [Institut fuer Halbleiter-und Mikrosystemtechnik (IHM) Technische Universitaet Dresden, Helmholtzstrasse 10, 01062 Dresden (Germany); Herrmann, D. [Institut fuer Halbleiter-und Mikrosystemtechnik (IHM) Technische Universitaet Dresden, Helmholtzstrasse 10, 01062 Dresden (Germany); Zentrum fuer Sonnenenergie-und Wasserstoff-Forschung (ZSW) Industriestrasse 6, 70565 Stuttgart (Germany); Huebner, R. [Institut fuer Halbleiter-und Mikrosystemtechnik (IHM) Technische Universitaet Dresden, Helmholtzstrasse 10, 01062 Dresden (Germany); Leibniz Institut fuer Festkoerper-und Werkstoffforschung Dresden (IFW) Helmholtzstrasse 20, 01069, Dresden (Germany); Zhang, Z.L. [Institut fuer Halbleiter-und Mikrosystemtechnik (IHM) Technische Universitaet Dresden, Helmholtzstrasse 10, 01062 Dresden (Germany); Max-Planck-Gesellschaft fuer Metallforschung (MPI) Heisenbergstrasse 3, 70569 Stuttgart (Germany); Bartha, J.W. [Institut fuer Halbleiter-und Mikrosystemtechnik (IHM) Technische Universitaet Dresden, Helmholtzstrasse 10, 01062 Dresden (Germany)

    2006-12-05

    Flexible thin-film solar cells require flexible encapsulation to protect the copper-indium-2 selenide (CIS) absorber layer from humidity and aggressive environmental influences. Tantalum-silicon-based diffusion barriers are currently a favorite material to prevent future semiconductor devices from copper diffusion. In this work tantalum-silicon-nitrogen (Ta-Si-N) and tantalum-silicon-oxygen (Ta-Si-O) films were investigated and optimized for thin-film solar cell encapsulation of next-generation flexible solar modules. CIS solar modules were coated with tantalum-based barrier layers. The performance of the thin-film barrier encapsulation was determined by measuring the remaining module efficiency after a 1000 h accelerated aging test. A significantly enhanced stability against humidity diffusion in comparison to non-encapsulated modules was reached with a reactively sputtered thin-film system consisting of 250 nm Ta-Si-O and 15 nm Ta-Si-N.

  17. Cooperative effect of roscovitine and irradiation targets angiogenesis and induces vascular destabilization in human breast carcinoma.

    Science.gov (United States)

    Maggiorella, L; Aubel, C; Haton, C; Milliat, F; Connault, E; Opolon, P; Deutsch, E; Bourhis, J

    2009-02-01

    Angiogenesis is considered as an essential process for tumour development and invasion. Previously, we demonstrated that cyclin-dependent kinase inhibition by roscovitine induces a radiosensitization and a synergistic antitumoral effect in human carcinoma but its effect on the microenvironment and tumour angiogenesis remains unknown. Here, we investigated the effect of the combination roscovitine and ionizing radiation (IR) on normal cells in vitro and on tumour angiogenesis in MDA-MB 231 tumour xenografts. We observed that the combination roscovitine and IR induced a marked reduction of angiogenic hot spot and microvascular density in comparison with IR or roscovitine treatments alone. The Ang-2/Tie-2 ratio was increased in presence of reduced vascular endothelial growth factor level suggesting vessel destabilization. In vitro, no radiosensitization effect of roscovitine was found in endothelial, fibroblast, and keratinocyte cells. IR potentiated the antiproliferative effect of roscovitine without inducing apoptosis in endothelial cells. Roscovitine decreased IR-stimulated vascular endothelial growth factor secretion of MDA-MB 231 and endothelial cells. A reduction in the endothelial cells invasion and the capillary-like tube formation in Matrigel were observed following the combination roscovitine and IR. This combined treatment targets angiogenesis resulting in microvessel destabilization without inducing normal cell toxicity.

  18. Experimental and theoretical study of the yields of residual product nuclei produced in thin targets irradiated by 100-2600 MeV protons

    CERN Document Server

    Titarenko, Y E; Karpikhin, E I

    2003-01-01

    The objective of the project is measurements and computer simulations of independent and cumulative yields of residual product nuclei in thin targets relevant as target materials and structure materials for hybrid accelerator-driven systems coupled to high-energy proton accelerators. The yields of residual product nuclei are of great importance when estimating such basic radiation-technology characteristics of hybrid facility targets as the total target activity, target 'poisoning', buildup of long-lived nuclides that, in turn, are to be transmuted, product nuclide (Po) alpha-activity, content of low-pressure evaporated nuclides (Hg), content of chemically-active nuclides that spoil drastically the corrosion resistance of the facility structure materials, etc. In view of the above, radioactive product nuclide yields from targets and structure materials were determined by an experiment using the ITEP U-10 proton accelerator in 51 irradiation runs for different thin targets: sup 1 sup 8 sup 2 sup , sup 1 sup 8 ...

  19. Spatial distribution of neutrons in paraffin moderator surrounding a lead target irradiated with protons at intermediate energies

    CERN Document Server

    Adam, J; Bradnova, V

    2002-01-01

    The distribution of neutrons emitted during the irradiation with 0.65, 1.0 and 1.5 GeV protons from a lead target (O / = 8 cm, l = 20 cm) and moderated by a surrounding paraffin moderator of 6 cm thick was studied with a radiochemical sensor along the beam axis on top of the moderator. Small sup 1 sup 3 sup 9 La-sensors of approximately 1 g were used to measure essentially the thermal neutron fluence at different depths near the surface: i.e., on top of the moderator, in 10 mm deep holes and in 20 mm deep holes. The reaction sup 1 sup 3 sup 9 La(n, gamma) sup 1 sup 4 sup 0 La (tau sub 1 sub / sub 2 = 40.27 h) was studied using standard procedures of gamma spectroscopy and data analysis. The neutron induced activity of sup 1 sup 4 sup 0 La increases strongly with the depth of the hole inside the moderator, its activity distribution along the beam direction on top of the moderator has its maximum about 10 cm downstream the entrance of the protons into the lead and the induced activity increases about linearity ...

  20. Mapping patterns of nodal metastases in esophageal carcinoma: rethinking the clinical target volume for supraclavicular nodal irradiation

    Science.gov (United States)

    Luo, Yijun; Liu, Yuhui; Wang, Xiaoli; Zhang, Bin; Yu, Jinming; Wang, Chengang; Huang, Yong

    2016-01-01

    Background To map detail distribution of metastatic supraclavicular (SCV) lymph nodes (LN) in esophageal cancer (EC) patients and determine the precise radiation therapy clinical target volume (CTV). Methods A total of 101 thoracic esophageal carcinoma patients after surgery experienced SCV LN metastasis were retrospectively examined. The SCV region is further divided into four subgroups. Using hand drawings registration, nodes were mapped to a template computed tomogram to provide a visual impression of nodal frequencies and anatomic distribution. Results In all, 158 nodes were considered to be clinical metastatic in the SCV region in the 101 patients, 74 on the left and 84 on the right. Seven of 158 (4.4%) positive LN were located in group I, 78 of 158 (49.37%) were located in group II, 72 of 158 nodes (45.6%) were located in group III, 1 of 158 (0.63%) located in group IV. Conclusions According to our results, the SCV group II and group III are considered to be the high risk regions of esophageal squamous cell carcinoma (ESCC) LN metastasis, which were defined as elective nodal irradiation (ENI) areas. PMID:28066592

  1. Study of neutron spectra in a water bath from a Pb target irradiated by 250 MeV protons

    Science.gov (United States)

    Li, Yan-Yan; Zhang, Xue-Ying; Ju, Yong-Qin; Ma, Fei; Zhang, Hong-Bin; Chen, Liang; Ge, Hong-Lin; Wan, Bo; Luo, Peng; Zhou, Bin; Zhang, Yan-Bin; Li, Jian-Yang; Xu, Jun-Kui; Wang, Song-Lin; Yang, Yong-Wei; Yang, Lei

    2015-04-01

    Spallation neutrons were produced by the irradiation of Pb with 250 MeV protons. The Pb target was surrounded by water which was used to slow down the emitted neutrons. The moderated neutrons in the water bath were measured by using the resonance detectors of Au, Mn and In with a cadmium (Cd) cover. According to the measured activities of the foils, the neutron flux at different resonance energies were deduced and the epithermal neutron spectra were proposed. Corresponding results calculated with the Monte Carlo code MCNPX were compared with the experimental data to check the validity of the code. The comparison showed that the simulation could give a good prediction for the neutron spectra above 50 eV, while the finite thickness of the foils greatly effected the experimental data in low energy. It was also found that the resonance detectors themselves had great impact on the simulated energy spectra. Supported by National Natural Science Foundation and Strategic Priority Research Program of the Chinese Academy of Sciences (11305229, 11105186, 91226107, 91026009, XDA03030300)

  2. Effect of sodium injection rate in reduction process on characteristics of tantalum powders

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    The paper presents a research the effect of sodium injection rate in a melt containing potassium tantalum fluoride and a flux on morphology and characteristics of tantalum powders obtained by sodium reduction.

  3. Differential Regulation of Ferritin Subunits and Iron Transport Proteins: An Effect of Targeted Hepatic X-Irradiation

    Directory of Open Access Journals (Sweden)

    Naila Naz

    2013-01-01

    Full Text Available The current study aimed to investigate radiation-induced regulation of iron proteins including ferritin subunits in rats. Rat livers were selectively irradiated in vivo at 25 Gy. This dose can be used to model radiation effects to the liver without inducing overt radiation-induced liver disease. Sham-irradiated rats served as controls. Isolated hepatocytes were irradiated at 8 Gy. Ferritin light polypeptide (FTL was detectable in the serum of sham-irradiated rats with an increase after irradiation. Liver irradiation increased hepatic protein expression of both ferritin subunits. A rather early increase (3 h was observed for hepatic TfR1 and Fpn-1 followed by a decrease at 12 h. The increase in TfR2 persisted over the observed time. Parallel to the elevation of AST levels, a significant increase (24 h in hepatic iron content was measured. Complete blood count analysis showed a significant decrease in leukocyte number with an early increase in neutrophil granulocytes and a decrease in lymphocytes. In vitro, a significant increase in ferritin subunits at mRNA level was detected after irradiation which was further induced with a combination treatment of irradiation and acute phase cytokine. Irradiation can directly alter the expression of ferritin subunits and this response can be strongly influenced by radiation-induced proinflammatory cytokines. FTL can be used as a serum marker for early phase radiation-induced liver damage.

  4. International strategic minerals inventory summary report; niobium (columbium) and tantalum

    Science.gov (United States)

    Crockett, R.N.; Sutphin, D.M.

    1993-01-01

    Major world resources of niobium and tantalum are described in this summary report of information in the International Strategic Minerals Inventory (ISMI). ISMI is a cooperative data-collection effort of earth-science and mineral-resource agencies in Australia, Canada, the Federal Republic of Germany, the Republic of South Africa, the United Kingdom, and the United States of America. Part I of this report presents an overview of the resources and potential supply of niobium and tantalum based on inventory information; Part II contains tables of both geologic and mineral-resource information and includes production data collected by ISMI participants. Niobium is used principally as an alloying element in special steels and superalloys, and tantalum is used mainly in electronics. Minerals in the columbite-tantalite series are principal ore minerals of niobium and tantalum. Pyrochlore is a principal source of niobium. These minerals are found in carbonatite, certain rocks in alkaline igneous complexes, pegmatite, and placer deposits. ISMI estimates show that there are over 7 million metric tons of niobium and almost 0.5 million metric tons of tantalum in known deposits, outside of China and the former Soviet Union, for which reliable estimates have been made. Brazilian deposits, followed by Canadian deposits, contain by far the largest source of niobium. Tantalum production is spread widely among several countries, and Brazil and Canada are the most significant of these producers. Brazil's position is further strengthened by potential byproduct columbite from tin mining. Present economically exploitable resources of niobium appear to be sufficient for the near future, but Brazil will continue to be the predominant world supplier of ferrocolumbium. Tantalum, a byproduct of tin production, has been captive to the fluctuations of that market, but resources in pegmatite in Canada and Australia make it likely that future increases in the present modest demand will be met.

  5. Comparison on the production of radionuclides in 1.4 GeV proton irradiated LBE targets of different thickness

    CERN Document Server

    Maiti, Moumita; Mendonça, Tania M; Stora, Thierry; Lahiri, Susanta

    2014-01-01

    This is the first report on the inventory of radionuclides produced in 1.4 GeV proton induced reaction on Lead-Bismuth Eutectic (LBE) targets. LBE targets of 6 mm diameter and 1 to 8 mm lengths were irradiated with 1.4 GeV protons. The radionuclides ranging from Be-7 (53.12 days) to Po-207 (5.8 h) were identified in the samples with the help of time resolved gamma-ray spectroscopy. However, there is no signature of formation of At radioisotopes, which can be produced by the interaction of secondary particles, typical for thick targets.

  6. Critical Defense Materials: Government Collected Data Are Sufficiently Reliable to Assess Tantalum Availability

    Science.gov (United States)

    2016-03-01

    collection methods . For example, government data prepared by the United States Geological Survey (USGS) on tantalum production reports information on...mined at prevailing prices.4 Countries for which the USGS reported tantalum mine production in 2014 are Brazil , Burundi, China, Democratic Republic of...Data Are Sufficiently Reliable to Assess Tantalum Availability Why GAO Did This Study The United States relies on foreign mine production of tantalum

  7. Tantalum strength model incorporating temperature, strain rate and pressure

    Science.gov (United States)

    Lim, Hojun; Battaile, Corbett; Brown, Justin; Lane, Matt

    Tantalum is a body-centered-cubic (BCC) refractory metal that is widely used in many applications in high temperature, strain rate and pressure environments. In this work, we propose a physically-based strength model for tantalum that incorporates effects of temperature, strain rate and pressure. A constitutive model for single crystal tantalum is developed based on dislocation kink-pair theory, and calibrated to measurements on single crystal specimens. The model is then used to predict deformations of single- and polycrystalline tantalum. In addition, the proposed strength model is implemented into Sandia's ALEGRA solid dynamics code to predict plastic deformations of tantalum in engineering-scale applications at extreme conditions, e.g. Taylor impact tests and Z machine's high pressure ramp compression tests, and the results are compared with available experimental data. Sandia National Laboratories is a multi program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

  8. R&D of A MW-class solid-target for a spallation neutron source

    Science.gov (United States)

    Kawai, Masayoshi; Furusaka, Michihiro; Kikuchi, Kenji; Kurishita, Hiroaki; Watanabe, Ryuzo; Li, Jing-Feng; Sugimoto, Katsuhisa; Yamamura, Tsutomu; Hiraoka, Yutaka; Abe, Katsunori; Hasegawa, Akira; Yoshiie, Masatoshi; Takenaka, Hiroyuki; Mishima, Katsuichiro; Kiyanagi, Yoshiaki; Tanabe, Tetsuo; Yoshida, Naoaki; Igarashi, Tadashi

    2003-05-01

    R&D for a MW-class solid target composed of tungsten was undertaken to produce a pulsed intense neutron source for a future neutron scattering-facility. In order to solve the corrosion of tungsten, tungsten target blocks were clad with tantalum by means of HIP'ing, brazing and electrolytic coating in a molten salt bath. The applicability of the HIP'ing method was tested through fabricating target blocks for KENS (spallation neutron source at KEK). A further investigation to certify the optimum HIP conditions was made with the small punch test method. The results showed that the optimum temperature was 1500 °C at which the W/Ta interface gave the strongest fracture strength. In the case of the block with a hole for thermocouple, it was found that the fabrication preciseness of a straight hole and a tantalum sheath influenced the results. The development of a tungsten stainless-steel alloy was tried to produce a bare tungsten target, using techniques in powder metallurgy. Corrosion tests for various tungsten alloys were made while varying the water temperature and velocity. The mass loss of tungsten in very slow water at 180 °C was as low as 0.022 mg/y, but increased remarkably with water velocity. Simulation experiments for radiation damage to supplement the STIP-III experiments were made to investigate material hardening by hydrogen and helium, and microstructures irradiated by electrons. Both experiments showed consistent results on the order of the dislocation numbers and irradiation hardness among the different tungsten materials. Thermal-hydraulic designs were made for two types of solid target system of tungsten: slab and rod geometry as a function of the proton beam power. The neutronic performance of a solid target system was compared with that of mercury target based on Monte Carlo calculations by using the MCNP code.

  9. Non-targeted transcriptomic effects upon thyroid irradiation: similarity between in-field and out-of-field responses varies with tissue type.

    Science.gov (United States)

    Langen, Britta; Rudqvist, Nils; Spetz, Johan; Swanpalmer, John; Helou, Khalil; Forssell-Aronsson, Eva

    2016-10-25

    Non-targeted effects can induce responses in tissues that have not been exposed to ionizing radiation. Despite their relevance for risk assessment, few studies have investigated these effects in vivo. In particular, these effects have not been studied in context with thyroid exposure, which can occur e.g. during irradiation of head and neck tumors. To determine the similarity between in-field and out-of-field responses in normal tissue, we used a partial body irradiation setup with female mice where the thyroid region, the thorax and abdomen, or all three regions were irradiated. After 24 h, transcriptional regulation in the kidney cortex, kidney medulla, liver, lungs, spleen, and thyroid was analyzed using microarray technology. Thyroid irradiation resulted in transcriptional regulation in the kidney medulla and liver that resembled regulation upon direct exposure of these tissues regarding both strength of response and associated biological function. The kidney cortex showed fewer similarities between the setups, while the lungs and spleen showed little similarity between in-field and out-of-field responses. Interestingly, effects were generally not found to be additive. Future studies are needed to identify the molecular mechanisms that mediate these systemic effects, so that they may be used as targets to minimize detrimental side effects in radiotherapy.

  10. Fine target of deuterium; Blanco fino de deuterio

    Energy Technology Data Exchange (ETDEWEB)

    Diaz Diaz, J.; Granados Gonzalez, C. E.; Gutierrez Bernal, R.

    1959-07-01

    A fine target of deuterium on a tantalum plate by the absorption method is obtained. In order to obtain the de gasification temperature an induction generator of high frequency is used and the deuterium pass is regulated by means of a palladium valve. Two vacuum measures are available, one to measure the high vacuum in the de gasification process of the tantalum plate and the other, for low vacuum, to measure the deuterium inlet in the installation and the deuterium pressure change in the installation after the absorption in the tantalum plate. A target of 48 {mu} gr/cm{sup 2} thick is obtained. (Author) 1 refs.

  11. Plasma-nitriding of tantalum at relatively low temperature

    Institute of Scientific and Technical Information of China (English)

    ZHANG Deyuan; LIN Qin; ZHAO Haomin; FEI Qinyong; GENG Man

    2004-01-01

    The combined quadratic orthogonal regression method of experiment design was employed to explore the effects of process parameters of plasma nitriding of tantalum such as total pressure, temperature and original hydrogen molar fraction on the hardness, roughness and structure of nitriding surfaces. The regression equations of hardness, roughness and structure were given according to the results of regression and statistic analysis. And the diffusion activation energy of nitrogen in tantalum on plasma nitriding conditions was calculated according to the experimental data of hardness of plasma-nitriding of tantalum vs time and temperature. The diffusion activation energy calculated belongs to (155.49 + 10.51)kJ/mol (783-983 K).

  12. Advanced Wet Tantalum Capacitors: Design, Specifications and Performance

    Science.gov (United States)

    Teverovsky, Alexander

    2017-01-01

    Insertion of new types of commercial, high volumetric efficiency wet tantalum capacitors in space systems requires reassessment of the existing quality assurance approaches that have been developed for capacitors manufactured to MIL-PRF-39006 requirements. The specifics of wet electrolytic capacitors is that leakage currents flowing through electrolyte can cause gas generation resulting in building up of internal gas pressure and rupture of the case. The risk associated with excessive leakage currents and increased pressure is greater for high value advanced wet tantalum capacitors, but it has not been properly evaluated yet. This presentation gives a review of specifics of the design, performance, and potential reliability risks associated with advanced wet tantalum capacitors. Problems related to setting adequate requirements for DPA, leakage currents, hermeticity, stability at low and high temperatures, ripple currents for parts operating in vacuum, and random vibration testing are discussed. Recommendations for screening and qualification to reduce risks of failures have been suggested.

  13. Change in lattice parameter of tantalum due to dissolved hydrogen

    Directory of Open Access Journals (Sweden)

    Gyanendra P. Tiwari

    2012-06-01

    Full Text Available The volume expansion of tantalum due to the dissolved hydrogen has been determined using Bragg equation. The hydrogen was dissolved in the pure tantalum metal at constant temperature (360 °C and constant pressure (132 mbar by varying the duration of hydrogen charging. The amount of dissolved hydrogen was within the solid solubility limit. The samples with different hydrogen concentration were analyzed by X-ray diffraction technique. Slight peak shifts as well as peak broadening were observed. The relative changes of lattice parameters plotted against the hydrogen concentration revealed that the lattice parameters varied linearly with the hydrogen concentration.

  14. Wetting layer of copper on the tantalum (001) surface

    Science.gov (United States)

    Dupraz, Maxime; Poloni, Roberta; Ratter, Kitti; Rodney, David; De Santis, Maurizio; Gilles, Bruno; Beutier, Guillaume; Verdier, Marc

    2016-12-01

    The heteroepitaxial interface formed by copper deposited onto the tantalum (001) surface is studied by surface x-ray diffraction and ab initio calculations. The analysis of the crystal truncation rods reveals the presence of a wetting layer of copper made of two atomic planes pseudomorphic to the tantalum substrate, with the upper most atomic planes significantly deformed. These findings are in total agreement with the results of density-functional-theory calculations. The presence of the wetting layer confirms a Stranski-Krastanov growth mode and is thought to explain the extremely fast atomic diffusion of copper during the dewetting process in the solid state at high temperature.

  15. Complications associated with use of tantalum-mesh--covered implants.

    Science.gov (United States)

    Przybyla, V A; La Piana, F G

    1982-02-01

    In 1948, ophthalmologists started implanting plastic spheres partially covered with tantalum mesh (eg, the Valley Forge Implant) in anophthalmic sockets. Numerous patients have developed complications ten to 15 years after surgery: pain ("pinching" or "deep"), headache, heavy mucopurulent discharge and diffuse conjunctival inflammation, migration of the implant, thinning or erosion of tissues covering the implant (extrusion), and inability to wear an artificial eye. Management includes refabrication of the artificial eye and replacement of the implant with a dermis-fat graft or a silicone ball plus scleral graft. Tantalum-mesh--covered orbital implants should probably not be used.

  16. Ion beam and dual ion beam sputter deposition of tantalum oxide films

    Science.gov (United States)

    Cevro, Mirza; Carter, George

    1994-11-01

    Ion beam sputter deposition (IBS) and dual ion beam sputter deposition (DIBS) of tantalum oxide films was investigated at room temperature and compared with similar films prepared by e-gun deposition. Optical properties ie refractive index and extinction coefficient of IBS films were determined in the 250 - 1100 nm range by transmission spectrophotometry and at (lambda) equals 632.8 nm by ellipsometry. They were found to be mainly sensitive to the partial pressure of oxygen used as a reactive gas in the deposition process. The maximum value of the refractive index of IBS deposited tantalum oxide films was n equals 2.15 at (lambda) equals 550 nm and the extinction coefficient of order k equals 2 X 10-4. Films deposited by e-gun deposition had refractive index n equals 2.06 at (lambda) equals 550 nm. Films deposited using DIBS ie deposition assisted by low energy Ar and O2 ions (Ea equals 0 - 300 eV) and low current density (Ji equals 0 - 40 (mu) A/cm2) showed no improvement in the optical properties of the films. Preferential sputtering occurred at Ea(Ar) equals 300 eV and Ji equals 20 (mu) A/cm2 and slightly oxygen deficient films were formed. Different bonding states in the tantalum-oxide films were determined by x-ray spectroscopy while composition of the film and contaminants were determined by Rutherford scattering spectroscopy. Tantalum oxide films formed by IBS contained relatively high Ar content (approximately equals 2.5%) originating from the reflected argon neutrals from the sputtering target while assisted deposition slightly increased the Ar content. Stress in the IBS deposited films was measured by the bending technique. IBS deposited films showed compressive stress with a typical value of s equals 3.2 X 109 dyn/cm2. Films deposited by concurrent ion bombardment showed an increase in the stress as a function of applied current density. The maximum was s approximately equals 5.6 X 109 dyn/cm2 for Ea equals 300 eV and Ji equals 35 (mu) A/cm2. All

  17. Ion-beam and dual-ion-beam sputter deposition of tantalum oxide films

    Science.gov (United States)

    Cevro, Mirza; Carter, George

    1995-02-01

    Ion-beam sputter deposition (IBS) and dual-ion-beam sputter deposition (DIBS) of tantalum oxide films was investigated at room temperature and compared with similar films prepared by e-gun deposition. The optical properties, i.e., refractive index and extinction coefficient, of IBS films were determined in the 250- to 1100-nm range by transmission spectrophotometry and at (lambda) equals 632.8 nm by ellipsometry. They were found to be mainly sensitive to the partial pressure of oxygen used as a reactive gas in the deposition process. The maximum value of the refractive index of IBS deposited tantalum oxide films was n equals 2.15 at (lambda) equals 550 nm and the extinction coefficient of order k equals 2 X 10-4. Films deposited by e-gun deposition had refractive index n 2.06 at (lambda) equals 550 nm. Films deposited using DIBS, i.e., deposition assisted by low energy Ar and O2 ions (Ea equals 0 to 300 eV) and low current density (Ji equals 0 to 40 (mu) A/cm2), showed no improvement in the optical properties of the films. Preferential sputtering occurred at Ea(Ar) equals 300 eV and Ji equals 20 (mu) A/cm2 and slightly oxygen deficient films were formed. Different bonding states in the tantalum-oxide films were determined by x-ray spectroscopy, whereas composition of the film and contaminants were determined by Rutherford backscattering spectroscopy (RBS). Tantalum oxide films formed by IBS contained relatively high Ar content (approximately equals 2.5%) originating from the reflected argon neutrals from the sputtering target whereas assisted deposition slightly increased the Ar content. Stress in the IBS-deposited films was measured by the bending technique. IBS-deposited films showed compressive stress with a typical value of s equals 3.2 X 109 dyn/cm2. Films deposited by concurrent ion bombardment showed an increase in the stress as a function of applied current density. The maximum was s approximately equals 5.6 X 109 dyn/cm2 for Ea equals 300 eV and Ji equals

  18. Diffusion of liquid uranium into foils of tantalum metal and tantalum-10 wt% tungsten alloy up to 1350/sup 0/C

    Energy Technology Data Exchange (ETDEWEB)

    Kuznietz, M.; Livne, Z.; Cotler, C.; Erez, G.

    1988-05-01

    Immersion experiments have been performed to investigate the diffusion of liquid uranium into 0.3 mm thick foils of tantalum metal and tantalum-10wt% tungsten alloy in the temperature range of 1160/sup 0/C to 1350/sup 0/C, for reaction times up to 20 h, in zirconia crucibles. The orginal and uranium-reacted foils have been studied microscopically (SEM-EDAX) and a multilayer structure is revealed in the reacted foils. Layers identified for tantalum immersed in uranium: Uranium-tantalum (U/Ta approx. = 1), precipitated columnar tantalum (< 1wt% U), inner uranium, and inner tantalum (with grown grains and uranium along grain boundaries). Layers identified for Ta-10wt% W alloy immersed in uranium: Uranium-tantalum (U/Ta approx. = 1, 0.3wt% W), precipitated tantalum (< 1wt% U, down to 1-2wt% W), and inner Escher-type grains of tantalum-tungsten (up to 18wt% W) and of uranium (< 2wt% Ta, < 0.4wt% W). A mechanism for the multilayer formation and the intrusion of liquid uranium into the solid foils is proposed and substantiated.

  19. The Pattern of Failure after Re-Irradiation of Recurrent Squamous Cell Head and Neck Cancer: Implications for Defining the Targets

    Science.gov (United States)

    Popovtzer, Aron; Gluck, Iris; Chepeha, Douglas B; Teknos, Theodoros N; Moyer, Jeffrey S; Prince, Mark E; Bradford, Carol R; Eisbruch, Avraham

    2009-01-01

    Purpose Re-irradiation (re-RT) of recurrent head and neck cancer (HNC) may achieve long term disease control in some patients, at the expense of high rates of late sequelae. Limiting the re-RT targets to the recurrent gross tumor volume (rGTV) would reduce the volumes of re-irradiated tissues, however, its effect on tumor recurrence pattern is unknown. Methods Retrospective review of 66 patients who underwent curative-intent re-RT for non-resectable recurrent or second primary mucosal squamous cell HNC. Treatment was delivered with 3-dimensional conformal (3D) RT or intensity modulated RT (IMRT). The targets in all patients consisted of the rGTVs with tight (0.5 cm) margins, with no intent to treat prophylactically lymph nodes or sub-clinical disease in the vicinity of the rGTVs. The sites of local-regional failures (LRFs) were determined using imaging at the time of failure, and were compared to the rGTVs. Results Median re-RT dose was 68 Gy. 47 patients (71%) received concomitant chemotherapy and 31 (47%) received hyperfractionated, accelerated RT. At a median follow up 42 month, 16 (23%) are alive and free of disease. Fifty patients (77%) had a third recurrence or persistent disease, including 47 LRFs. All LRFs occurred within the rGTVs except for two (4%) (95% C.I. 0; 11 %). Nineteen patients (29%) had grade ≥3 late complications, mostly dysphagia (12 patients). Conclusion Almost all LRFs occurred within the re-irradiated rGTVs despite avoiding prophylactic RT of tissue at risk of subclinical disease. These results support confining the re-RT targets to the rGTVs to reduce re-irradiated tissue volumes. PMID:19135312

  20. An automated flow system incorporating in-line acid dissolution of bismuth metal from a cyclotron irradiated target assembly for use in the isolation of astatine-211

    Energy Technology Data Exchange (ETDEWEB)

    O’Hara, Matthew J.; Krzysko, Anthony J.; Niver, Cynthia M.; Morrison, Samuel S.; Owsley, Stanley L.; Hamlin, Donald K.; Dorman, Eric F.; Scott Wilbur, D.

    2017-04-01

    Astatine-211 (211At) is a promising cyclotron-produced radionuclide being investigated for use in targeted alpha therapy of blood borne and metastatic cancers, as well as treatment of tumor remnants after surgical resections. The isolation of trace quantities of 211At, produced within several grams of a Bi metal cyclotron target, involves a complex, multi-step procedure: (1) Bi metal dissolution in strong HNO3, (2) distillation of the HNO3 to yield Bi salts containing 211At, (3) dissolution of the salts in strong HCl, (4) solvent extraction of 211At from bismuth salts with diisopropyl ether (DIPE), and (5) back-extraction of 211At from DIPE into NaOH, leading to a purified 211At product. Step (1) has been addressed first to begin the process of automating the onerous 211At isolation process. A computer-controlled Bi target dissolution system has been designed. The system performs in-line dissolution of Bi metal from the target assembly using an enclosed target dissolution block, routing the resulting solubilized 211At/Bi mixture to the subsequent process step. The primary parameters involved in Bi metal solubilization (HNO3 concentration and influent flow rate) were optimized prior to evaluation of the system performance on replicate cyclotron irradiated targets. The results indicate that the system performs reproducibly, having nearly quantitative release of 211At from irradiated targets, with cumulative 211At recoveries that follow a sigmoidal function. The predictable nature of the 211At release profile allows the user to tune the system to meet target processing requirements.

  1. Novel Approaches for Concurrent Irradiation in Locally Advanced Cervical Cancer: Platinum Combinations, Non-Platinum-Containing Regimens, and Molecular Targeted Agents

    Directory of Open Access Journals (Sweden)

    Giannis Mountzios

    2013-01-01

    Full Text Available Despite the available prevention and early detection strategies, squamous-cell carcinoma of the uterine cervix is still diagnosed as locally advanced disease in a considerable proportion of patients. As a potent sensitizer of cancer cells, cisplatin has been the “traditional partner” of external beam irradiation in this setting for more than two decades. Induction chemotherapy strategies followed by concurrent chemoradiation or surgery and preoperative concurrent chemoradiation have been recently implemented in clinical trials in an effort to optimize local control and to minimize the risk of distant metastases. In this context, cisplatin has been combined with a number of other potential radiosensitizers, including 5-fluorouracil, capecitabine, and gemcitabine. In patients resistant or intolerant to platinum compounds, numerous non-platinum-containing regimens have been developed, implementing various antimetabolites, taxanes, antineoplastic antibiotics, and topoisomerase II inhibitors. More recently, molecular agents targeting critical pathways in cervical malignant transformation are being assessed in early clinical trials in combination with external-beam irradiation. In the current work, we review the evolving role of cisplatin and other platinum compounds, either alone or in combination regimens, in the context of other potent radiosensitizers. The emerging role of molecular targeted agents, as candidate partners of external beam irradiation, is also discussed.

  2. Evaluation of residual stress in sputtered tantalum thin-film

    Energy Technology Data Exchange (ETDEWEB)

    Al-masha’al, Asa’ad, E-mail: asaad.al@ed.ac.uk; Bunting, Andrew; Cheung, Rebecca

    2016-05-15

    Highlights: • Tantalum thin-films have been deposited by DC magnetron sputtering system. • Thin-film stress is observed to be strongly influenced by sputtering pressure. • Transition towards the compressive stress is ascribed to the annealing at 300 °C. • Expose thin-film to air ambient or ion bombardment lead to a noticeable change in the residual stress. - Abstract: The influence of deposition conditions on the residual stress of sputtered tantalum thin-film has been evaluated in the present study. Films have been deposited by DC magnetron sputtering and curvature measurement method has been employed to calculate the residual stress of the films. Transitions of tantalum film stress from compressive to tensile state have been observed as the sputtering pressure increases. Also, the effect of annealing process at temperature range of 90–300 °C in oxygen ambient on the residual stress of the films has been studied. The results demonstrate that the residual stress of the films that have been deposited at lower sputtering pressure has become more compressive when annealed at 300 °C. Furthermore, the impact of exposure to atmospheric ambient on the tantalum film stress has been investigated by monitoring the variation of the residual stress of both annealed and unannealed films over time. The as-deposited films have been exposed to pure Argon energy bombardment and as result, a high compressive stress has been developed in the films.

  3. 21 CFR 886.3100 - Ophthalmic tantalum clip.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Ophthalmic tantalum clip. 886.3100 Section 886.3100 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... or temporarily to bring together the edges of a wound to aid healing or prevent bleeding from small...

  4. Fibronectin adsorption on tantalum: the influence of nanoroughness.

    Science.gov (United States)

    Hovgaard, Mads Bruun; Rechendorff, Kristian; Chevallier, Jacques; Foss, Morten; Besenbacher, Flemming

    2008-07-17

    The complex mechanisms of protein adsorption at the solid-liquid interface is of great importance in many research areas, including protein purification, biocompatibility of medical implants, biosensing, and biofouling. The protein adsorption process depends crucially on both the nanoscale chemistry and topography of the interface. Here, we investigate the adsorption of the cell-binding protein fibronectin on flat and nanometer scale rough tantalum oxide surfaces using ellipsometry and quartz crystal microbalance with dissipation (QCM-D). On the flat tantalum oxide surfaces, the interfacial protein spreading causes an increase in the rigidity and a decrease in the thickness of the adsorbed fibronectin layer with decreasing bulk protein concentration. For the tantalum oxide surfaces with well-controlled, stochastic nanometer scale roughness, similar concentration effects are observed for the rigidity of the fibronectin layer and saturated fibronectin uptake. However, we find that the nanorough tantalum oxide surfaces promote additional protein conformational changes, an effect especially apparent from the QCM-D signals, interpreted as an additional stiffening of the formed fibronectin layers.

  5. 2014 NEPP Tasks Update for Ceramic and Tantalum Capacitors

    Science.gov (United States)

    Teverovsky, Alexander A.

    2014-01-01

    Presentation describes recent development in research on MnO2, wet, and polymer tantalum capacitors. Low-voltage failures in multilayer ceramic capacitors and techniques to reveal precious metal electrode (PME) and base metal electrode (BME) capacitors with cracks are discussed. A voltage breakdown technique is suggested to select high quality low-voltage BME ceramic capacitors.

  6. Electrochemical Study of Tantalum in Fluoride and Oxofluoride Melts

    DEFF Research Database (Denmark)

    Polyakova, L.; Polyakov, E.; Matthiesen, F.

    1994-01-01

    The electrochemical behavior of tantalum in the form of K2TaF7 in an LiF-NaF-KF eutectic melt has been studied by linear voltammetry in the temperature range of 560 to 815-degrees-C with and without additions of Na2O. An amperometric titration has been performed by measuring the heights of the ca...

  7. Assembly and Irradiation Modeling of Residual Stresses in Low-Enriched Uranium Foil-Based Annular Targets for Molybdenum-99 Production

    Directory of Open Access Journals (Sweden)

    Srisharan G. Govindarajan

    2013-01-01

    Full Text Available This paper considers a composite cylindrical structure, with low-enriched uranium (LEU foil enclosed between two aluminum 6061-T6 cylinders. A recess is cut all around the outer circumference of the inner tube to accommodate the LEU foil of open-cross section. To obtain perfect contact at the interfaces of the foil and the tubes, an internal pressure is applied to the inner tube, thereby plastically and elastically deforming it. The residual stresses resulting from the assembly process are used along with a thermal stress model to predict the stress margins in the cladding during irradiation. The whole process was simulated as a steady-state two-dimensional problem using the commercial finite element code Abaqus FEA. The irradiation behavior of the annular target has been presented, and the effect of the assembly residual stresses has been discussed.

  8. Research on control method of Tantalum wet metallurgy based on ANFIS%基于 ANFIS的钽湿法冶炼控制方法研究

    Institute of Scientific and Technical Information of China (English)

    宋威; 吴可; 林满山

    2015-01-01

    To solve the problem of experience-based decision made in Tantalum wet metallurgy, a control method of Tantalum wet metallurgy based on Adaptive Network-based Fuzzy Inference System ( ANFIS) is proposed. By analyzing the control target of Tantalum wet metallurgy,the control model is constructed. Then,the structure and technique realization of ANFIS is described. And the control process is presented in detail. Experimental results show that the proposed method can ensure the temperature of reaction tank rises steadily, which lays foundation for safety production of Tantalum wet metallurgy.%针对钽湿法冶炼生产决策主要依靠经验的问题,提出基于自适应神经模糊推理系统( ANFIS)的钽湿法冶炼控制方法。在分析钽湿法冶炼控制目标的基础上,构建控制模型,描述ANFIS结构与技术实现,并给出详细控制流程。实验结果表明,该方法实现了反应槽温度的平稳上升,能够确保钽湿法冶炼的安全生产。

  9. Co-targeting Deoxyribonucleic Acid–Dependent Protein Kinase and Poly(Adenosine Diphosphate-Ribose) Polymerase-1 Promotes Accelerated Senescence of Irradiated Cancer Cells

    Energy Technology Data Exchange (ETDEWEB)

    Azad, Arun, E-mail: arun.azad@bccancer.bc.ca [Division of Cancer Research, Peter MacCallum Cancer Centre, East Melbourne, Victoria (Australia); Department of Pathology, St. Vincent' s Hospital, University of Melbourne, Parkville, Victoria (Australia); Bukczynska, Patricia; Jackson, Susan [Division of Cancer Research, Peter MacCallum Cancer Centre, East Melbourne, Victoria (Australia); Haput, Ygal; Cullinane, Carleen [Division of Cancer Research, Peter MacCallum Cancer Centre, East Melbourne, Victoria (Australia); Sir Peter MacCallum Department of Oncology, University of Melbourne, Parkville, Victoria (Australia); McArthur, Grant A.; Solomon, Benjamin [Division of Cancer Research, Peter MacCallum Cancer Centre, East Melbourne, Victoria (Australia); Division of Cancer Medicine, Peter MacCallum Cancer Centre, East Melbourne, Victoria (Australia); Department of Medicine, St. Vincent' s Hospital, University of Melbourne, Parkville, Victoria (Australia); Sir Peter MacCallum Department of Oncology, University of Melbourne, Parkville, Victoria (Australia)

    2014-02-01

    Purpose: To examine the effects of combined blockade of DNA-dependent protein kinase (DNA-PK) and poly(adenosine diphosphate-ribose) polymerase-1 (PARP-1) on accelerated senescence in irradiated H460 and A549 non-small cell lung cancer cells. Methods and Materials: The effects of KU5788 and AG014699 (inhibitors of DNA-PK and PARP-1, respectively) on clonogenic survival, DNA double-strand breaks (DSBs), apoptosis, mitotic catastrophe, and accelerated senescence in irradiated cells were examined in vitro. For in vivo experiments, H460 xenografts established in athymic nude mice were treated with BEZ235 (a DNA-PK, ATM, and phosphatidylinositol 3-kinase/mammalian target of rapamycin inhibitor) and AG014699 to determine effects on proliferation, DNA DSBs, and accelerated senescence after radiation. Results: Compared with either inhibitor alone, combination treatment with KU57788 and AG014699 reduced postradiation clonogenic survival and significantly increased persistence of Gamma-H2AX (γH2AX) foci in irradiated H460 and A549 cells. Notably, these effects coincided with the induction of accelerated senescence in irradiated cells as reflected by positive β-galactosidase staining, G2-M cell-cycle arrest, enlarged and flattened cellular morphology, increased p21 expression, and senescence-associated cytokine secretion. In irradiated H460 xenografts, concurrent therapy with BEZ235 and AG014699 resulted in sustained Gamma-H2AX (γH2AX) staining and prominent β-galactosidase activity. Conclusion: Combined DNA-PK and PARP-1 blockade increased tumor cell radiosensitivity and enhanced the prosenescent properties of ionizing radiation in vitro and in vivo. These data provide a rationale for further preclinical and clinical testing of this therapeutic combination.

  10. Multi-scale Modeling of Plasticity in Tantalum.

    Energy Technology Data Exchange (ETDEWEB)

    Lim, Hojun [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Battaile, Corbett Chandler. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Carroll, Jay [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Buchheit, Thomas E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Boyce, Brad [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Weinberger, Christopher [Drexel Univ., Philadelphia, PA (United States)

    2015-12-01

    In this report, we present a multi-scale computational model to simulate plastic deformation of tantalum and validating experiments. In atomistic/ dislocation level, dislocation kink- pair theory is used to formulate temperature and strain rate dependent constitutive equations. The kink-pair theory is calibrated to available data from single crystal experiments to produce accurate and convenient constitutive laws. The model is then implemented into a BCC crystal plasticity finite element method (CP-FEM) model to predict temperature and strain rate dependent yield stresses of single and polycrystalline tantalum and compared with existing experimental data from the literature. Furthermore, classical continuum constitutive models describing temperature and strain rate dependent flow behaviors are fit to the yield stresses obtained from the CP-FEM polycrystal predictions. The model is then used to conduct hydro- dynamic simulations of Taylor cylinder impact test and compared with experiments. In order to validate the proposed tantalum CP-FEM model with experiments, we introduce a method for quantitative comparison of CP-FEM models with various experimental techniques. To mitigate the effects of unknown subsurface microstructure, tantalum tensile specimens with a pseudo-two-dimensional grain structure and grain sizes on the order of millimeters are used. A technique combining an electron back scatter diffraction (EBSD) and high resolution digital image correlation (HR-DIC) is used to measure the texture and sub-grain strain fields upon uniaxial tensile loading at various applied strains. Deformed specimens are also analyzed with optical profilometry measurements to obtain out-of- plane strain fields. These high resolution measurements are directly compared with large-scale CP-FEM predictions. This computational method directly links fundamental dislocation physics to plastic deformations in the grain-scale and to the engineering-scale applications. Furthermore, direct

  11. Phenomenological effets of tantalum incorporation into diamond films: Experimental and first principle studies

    Energy Technology Data Exchange (ETDEWEB)

    Ullah, Mahtab, E-mail: mahtabullah@bzu.edu.pk [Department of Physics, Bahauddin Zakariya University Multan (Pakistan); Rana, Anwar Manzoor; Ahmad, E. [Department of Physics, Bahauddin Zakariya University Multan (Pakistan); Raza, Rizwan [Department of Physics, COMSATS Institute of Information Technology, Lahore-54000 (Pakistan); Hussain, Fayyaz [Department of Physics, Bahauddin Zakariya University Multan (Pakistan); Hussain, Akhtar; Iqbal, Muhammad [Theoretical Physics Division, PINSTECH, P.O. Nilore, Islamabad (Pakistan)

    2016-09-01

    Graphical abstract: - Highlights: • Fabrication of tantalum incorporated diamonds films using HFCVD technique. • Decrease in resistivity by increasing tantalum content in diamond thin films. • Electronic structure calculations of tantalum incorporated diamonds films through VASP code. • A rise of bond length and bond angles by addition of tantalum in the diamond lattice. • Confirmation of decrease of resistivity by adding tantalum due to creation of impurity states in the bandgap. - Abstract: Tantalum (Ta) incorporated diamond films are synthesized on silicon substrate by chemical vapor deposition under gas mixture of CH{sub 4} + H{sub 2}. Characterizations of the resulting films indicate that morphology and resistivity of as-grown diamond films are significantly influenced by the process parameters and the amount of tantalum incorporated in the diamond films. XRD plots reveal that diamond films are composed of TaC along with diamond for higher concentration of tantalum and Ta{sub 2}C phases for lower concentration of tantalum. EDS spectra confirms the existence of tantalum in the diamond films. Resistivity measurements illustrate a sudden fall of about two orders of magnitude by the addition of tantalum in the diamond films. Band structure of Ta-incorporated diamond has been investigated based on density functional theory (DFT) using VASP code. Band structure calculations lead to the semiconducting behavior of Ta-incorporated diamond films because of the creation of defects states inside the band gap extending towards conduction band minimum. Present DFT results support experimental trend of resistivity that with the incorporation of tantalum into diamond lattice causes a decrease in the resistivity of diamond films so that tantalum-incorporated diamond films behave like a good semiconductor.

  12. Investigations on femtosecond-pulse-driven soft X-ray lasers using a gas puff target irradiated with a Ti:sapphire laser

    Energy Technology Data Exchange (ETDEWEB)

    Fiedorowicz, H.; Bartnik, A.; Szczurek, M. [Military Univ. of Technology, Warsaw (Poland). Inst. of Optoelectronics; Mocek, T.; Shin, H.J.; Cha, Y.H.; Lee, D.G.; Hong, K.H.; Nam, C.H. [Military Univ. of Technology, Warsaw (Poland). Inst. of Optoelectronics; Korea Advanced Inst. of Science and Technology, Taejon (Korea). Dept. of Physics

    2001-07-01

    Experimental investigations on soft X-ray lasers based on optical field ionization of gases with an ultrashort-pulse terawatt laser system are presented. The X-ray laser active medium was created using an elongated gas puff target formed by pulsed injection of a small amount of gas from a high-pressure electromagnetic valve through a nozzle in the form of a slit. The target was irradiated with a laser pulses from a 20-fs. 50-mJ Ti:Sapphire (Ti:S) laser system. Both recombination and collisional soft X-ray laser scheme have been studied. Soft X-ray spectra from nitrogen, oxygen, and xenon targets are presented and discussed. (orig.)

  13. INTERACTION OF LASER RADIATION WITH MATTER AND OTHER LASER APPLICATIONS: Changes in the emission properties of metal targets during pulse-periodic laser irradiation

    Science.gov (United States)

    Konov, Vitalii I.; Pimenov, S. M.; Prokhorov, A. M.; Chapliev, N. I.

    1988-02-01

    A scanning electron microscope was used with a pulse-periodic CO2 laser to discover the laws governing the correlation of the modified microrelief of metal surfaces, subjected to the action of multiple laser pulses, with the emission of charged particles and the luminescence of the irradiated zone. It was established that the influence of sorption and laser-induced desorption on the emission signals may be manifested differently depending on the regime of current generation in the "target-vacuum chamber" circuit.

  14. Comparison of the (p,xn) cross sections from /sup 238/U, /sup 235/U, and /sup 232/Th targets irradiated with 200-MeV protons

    Energy Technology Data Exchange (ETDEWEB)

    Chu, Y.Y.; Zhou, M.L.

    1982-01-01

    We have measured absolute cross sections for (p,xn) reactions (x ranges from 0 to 8) from /sup 238/U, /sup 235/U, and /sup 232/Th targets irradiated with 200-MeV protons at the Brookhaven AGS Linac injector. Chemical yields were determined by using /sup 239/Np and /sup 233/Pa as tracers. Yield patterns obtained in this work can be compared to the experimental results and theoretical calculations from earlier work, and they are consistent within the framework of intranuclear cascade followed by neutron evaporation and fission competition.

  15. Mineral-deposit model for lithium-cesium-tantalum pegmatites

    Science.gov (United States)

    Bradley, Dwight C.; McCauley, Andrew D.; Stillings, Lisa M.

    2017-06-20

    Lithium-cesium-tantalum (LCT) pegmatites comprise a compositionally defined subset of granitic pegmatites. The major minerals are quartz, potassium feldspar, albite, and muscovite; typical accessory minerals include biotite, garnet, tourmaline, and apatite. The principal lithium ore minerals are spodumene, petalite, and lepidolite; cesium mostly comes from pollucite; and tantalum mostly comes from columbite-tantalite. Tin ore as cassiterite and beryllium ore as beryl also occur in LCT pegmatites, as do a number of gemstones and high-value museum specimens of rare minerals. Individual crystals in LCT pegmatites can be enormous: the largest spodumene was 14 meters long, the largest beryl was 18 meters long, and the largest potassium feldspar was 49 meters long.Lithium-cesium-tantalum pegmatites account for about one-fourth of the world’s lithium production, most of the tantalum production, and all of the cesium production. Giant deposits include Tanco in Canada, Greenbushes in Australia, and Bikita in Zimbabwe. The largest lithium pegmatite in the United States, at King’s Mountain, North Carolina, is no longer being mined although large reserves of lithium remain. Depending on size and attitude of the pegmatite, a variety of mining techniques are used, including artisanal surface mining, open-pit surface mining, small underground workings, and large underground operations using room-and-pillar design. In favorable circumstances, what would otherwise be gangue minerals (quartz, potassium feldspar, albite, and muscovite) can be mined along with lithium and (or) tantalum as coproducts.Most LCT pegmatites are hosted in metamorphosed supracrustal rocks in the upper greenschist to lower amphibolite facies. Lithium-cesium-tantalum pegmatite intrusions generally are emplaced late during orogeny, with emplacement being controlled by pre-existing structures. Typically, they crop out near evolved, peraluminous granites and leucogranites from which they are inferred to be

  16. The technology of indirectly irradiated targets for inertial fusion researches at the Russian Federal nuclear center - VNIIEF

    Energy Technology Data Exchange (ETDEWEB)

    Andramanova, Y.V.; Veselov, A.V.; Zhidkov, N.V.; Ivanin, I.A.; Ignatev, Y.V.; Izgorodin, V.M.; Kirillov, G.A.; Komleva, G.A.; Makarov, M.Y.; Medvedev, E.F.; Morovov, A.P.; Nikolaev, G.P.; Pinegin, A.V.; Romaev, V.N.; Solomatina, E.Y.; Tacenko, M.V.; Tenyaev, B.N.; Cherkesova, I.N.; Yukhimchuk, A.A. [Russian Federal Nuclear Center, All-Russian Scientific Research Institute of Experimental Physics, RFNC-VNIIEF, Sarov (Russian Federation)

    2000-07-01

    The results of targets technology development for indirectly drive implosion experiments on the laser facility ISKRA-5, and also the constructions of targets developed at VNIIEF during last 4 years are represented. Moreover, a development of not destroying control methods for target parameters is written. (authors)

  17. Project and implantation of automation in irradiation systems for solid, liquid and gaseous targets in cyclotrons aiming the production of radioisotopes

    CERN Document Server

    Araujo, S G D

    2001-01-01

    Nowadays, two cyclotron are being operated at IPEN-CNEN/SP: one model CV-28, capable of accelerating p, d sup 3 He sub 4 and alpha, with energies of 24, 14, 36 and 28 MeV, respectively, and beam currents up to 30 mu A; the other one, model Cyclone 30, accelerates protons with energy of 30 MeV and currents up to 350 mu A. Both have the objective of irradiating targets both for radioisotopes production for use in nuclear medicine, such as sup 6 sup 7 Ga, sup 2 sup 0 sup 1 Tl, sup 1 sup 2 sup 3 I, sup 1 sup 8 F and general research. The development of irradiating systems completely automatic was the objective of this work, always aiming to reduce the radiation exposition dose to the workers and to increase the reliability of use of these systems, because very high activities are expected in these processes. In the automation, a Programmable Logical Controller (PCL) was used connected to a feedback net, to manage all the variables involved in the irradiation processes. The program of the PCL was developed using S...

  18. Nanocomposite tantalum-carbon-based films deposited by femtosecond pulsed laser ablation

    Energy Technology Data Exchange (ETDEWEB)

    Benchikh, N. [Laboratoire Traitement du Signal et Instrumentation, UMR 5516, Universite J. Monnet, 10 rue Barrouin, 42000 Saint-Etienne (France); Garrelie, F. [Laboratoire Traitement du Signal et Instrumentation, UMR 5516, Universite J. Monnet, 10 rue Barrouin, 42000 Saint-Etienne (France); Wolski, K. [Ecole Nationale Superieure des Mines de Saint-Etienne, Centre SMS - URA CNRS 5146, 158 cours Fauriel, 42023 Saint-Etienne, Cedex 02 (France); Donnet, C. [Laboratoire Traitement du Signal et Instrumentation, UMR 5516, Universite J. Monnet, 10 rue Barrouin, 42000 Saint-Etienne (France)]. E-mail: Christophe.Donnet@univ-st-etienne.fr; Fillit, R.Y. [Ecole Nationale Superieure des Mines de Saint-Etienne, Centre SMS - URA CNRS 5146, 158 cours Fauriel, 42023 Saint-Etienne, Cedex 02 (France); Rogemond, F. [Laboratoire Traitement du Signal et Instrumentation, UMR 5516, Universite J. Monnet, 10 rue Barrouin, 42000 Saint-Etienne (France); Subtil, J.L. [Laboratoire Traitement du Signal et Instrumentation, UMR 5516, Universite J. Monnet, 10 rue Barrouin, 42000 Saint-Etienne (France); Rouzaud, J.N. [Laboratoire de Geologie de l' Ecole Normale Superieure de Paris 24, rue Lhomond 75231-Paris Cedex 5 (France); Laval, J.Y. [Laboratoire de Physique du Solide, UPR5 CNRS-ESPCI, 10 rue Vauquelin 75231-Paris Cedex 05 (France)

    2006-01-03

    Nanostructured coatings of metal (tantalum) containing diamond-like carbon (a-C:Ta) have been prepared by femtosecond pulsed laser deposition (PLD). The films, containing 15 at.% tantalum, have been deposited by ablating sequentially graphite and metallic tantalum in vacuum conditions with an amplified Ti:sapphire laser. The coatings have been investigated by X-ray photoelectron spectroscopy, grazing angle X-ray diffraction, energy filtered transmission electron microscopy, scanning and high resolution transmission electron microscopies. Evidence of metallic {alpha}-Ta and {beta}-Ta particles (diameter in the 100 nm range) and smaller quasi-amorphous tantalum clusters embedded in the carbonaceous matrix have been shown. A thin tantalum carbide interface between the carbon matrix and the top surface of the tantalum nodules has also been identified. The ability of femtosecond pulsed laser deposition to synthetize nanocomposite carbon-based films and to control their nanostructure is discussed.

  19. Methods for chemical recovery of non-carrier-added radioactive tin from irradiated intermetallic Ti-Sb targets

    Science.gov (United States)

    Lapshina, Elena V [Troitsk, RU; Zhuikov, Boris L [Troitsk, RU; Srivastava, Suresh C [Setauket, NY; Ermolaev, Stanislav V [Obninsk, RU; Togaeva, Natalia R [Obninsk, RU

    2012-01-17

    The invention provides a method of chemical recovery of no-carrier-added radioactive tin (NCA radiotin) from intermetallide TiSb irradiated with accelerated charged particles. An irradiated sample of TiSb can be dissolved in acidic solutions. Antimony can be removed from the solution by extraction with dibutyl ether. Titanium in the form of peroxide can be separated from tin using chromatography on strong anion-exchange resin. In another embodiment NCA radiotin can be separated from iodide solution containing titanium by extraction with benzene, toluene or chloroform. NCA radiotin can be finally purified from the remaining antimony and other impurities using chromatography on silica gel. NCA tin-117m can be obtained from this process. NCA tin-117m can be used for labeling organic compounds and biological objects to be applied in medicine for imaging and therapy of various diseases.

  20. Century-Long Monitoring of Solar Irradiance and Earth's Albedo Using a Stable Scattering Target in Space

    CERN Document Server

    Judge, Philip G

    2015-01-01

    An inert sphere of a few meters diameter, placed in a special stable geosynchronous orbit in perpetuo, can be used for a variety of scientific experiments. Ground-based observations of such a sphere, "GeoSphere", can resolve very difficult problems in measuring the long-term solar irradiance. GeoSphere measurements will also help us understand the evolution of Earth's albedo and climate over at least the next century.

  1. Carbochlorination kinetics of tantalum and niobium pentoxides

    Directory of Open Access Journals (Sweden)

    Allain, E.

    1999-08-01

    Full Text Available The carbochlorination kinetics of pure Nb2O5 and Ta2O5 by gas mixture (C12 + CO + N2 between 380 and 1,000 °C is studied. A calculation of the standard free energy of the carbochlorination reactions is made. A diagram of the phases stability is drawn. The influence of the gas flow, temperature and the pardal pressure of Cl2 and CO at temperatures below 650 °C on the reaction rate is studied. The apparent activation energy is approximately 75 and 110 kJ/mol for Nb2Os and Ta2O5, respectively. At temperatures above 650°C the Arrhenius diagram presents an anomaly which may be attributed to the decomposition of the COCl2 formed in situ. The apparent reaction order of the carbochlorination of these oxides against Cl2+CO is approximately 2. The carbochlorination rates of these oxides are much greater than those of chlorination by Cl2 + N2. The carbochlorination kinetics of tin furnace slag leaching concentrates containing tantalum and niobium compounds are also studied and compared with the carbochlorination kinetics of the pure oxides.

    En este trabajo se estudia la cinética de carbocloruración del Nb2O5 y del Ta2O5 por la mezcla de gases (Cl2 + CO + N2 entre 380 y 1000°C. Se hace un cálculo de la energía libre estándar de carbocloruración y se dibujan los diagramas de equilibrio de fases. Se estudia la influencia del flujo de gas, la temperatura y la presión parcial de Cl2 y CO a temperaturas por debajo de 650°C sobre la velocidad de reacción. La energía de activación es aproximadamente 75 y 110 kJ/mol para el Nb2O5 y el Ta2O5, respectivamente. A temperaturas por encima de 650°C, el diagrama de Arrhenius presenta una anomalía que puede ser atribuida a la

  2. A Novel Method for Assessment of Polyethylene Liner Wear in Radiopaque Tantalum Acetabular Cups

    DEFF Research Database (Denmark)

    Troelsen, Anders; Greene, Meridith E; Ayers, David C

    2015-01-01

    Conventional radiostereometric analysis (RSA) for wear is not possible in patients with tantalum cups. We propose a novel method for wear analysis in tantalum cups. Wear was assessed by gold standard RSA and the novel method in total hip arthroplasty patients enrolled in a randomized controlled...... to the gold standard in titanium cups. The novel method offered accurate assessment and is a viable solution for assessment of wear in studies with tantalum cups....

  3. Mechanical properties of irradiated 9Cr-2WVTa steel

    Energy Technology Data Exchange (ETDEWEB)

    Klueh, R.L.; Alexander, D.J. [Oak Ridge National Lab., TN (United States); Rieth, M. [Forschungszentrum Karlsruhe (Germany). Inst. fuer Materialforschung II

    1998-09-01

    An Fe-9Cr-2W-0.25V-0.07Ta-0.1C (9Cr-2WVTa) steel has excellent strength and impact toughness before and after irradiation in the Fast Flux Test Facility and the High Flux Reactor (HFR). The ductile-brittle transition temperature (DBTT) increased only 32 C after 28 dpa at 365 C in FFTF, compared to a shift of {approx}60 C for a 9Cr-2WV steel--the same as the 9Cr-2WVTa steel but without tantalum. This difference occurred despite the two steels having similar tensile but without tantalum. This difference occurred despite the two steels having similar tensile properties before and after irradiation. The 9Cr-2WVTa steel has a smaller prior-austenite grain size, but otherwise microstructures are similar before irradiation and show similar changes during irradiation. The irradiation behavior of the 9Cr-2WVTa steel differs from the 9Cr-2WV steel and other similar steels in two ways: (1) the shift in DBTT of the 9Cr-2WVTa steel irradiated in FFTF does not saturate with fluence by {approx}28 dpa, whereas for the 9Cr-2WV steel and most similar steels, saturation occurs at <10 dpa, and (2) the shift in DBTT for 9Cr-2WVTa steel irradiated in FFTF and HFR increased with irradiation temperature, whereas it decreased for the 9Cr-2WV steel, as it does for most similar steels. The improved properties of the 9Cr-2WVTa steel and the differences with other steels were attributed to tantalum in solution.

  4. Research on wet purification method of metal tantalum powders by water and acid washing%金属钽粉湿法提纯的水洗和酸洗方法研究

    Institute of Scientific and Technical Information of China (English)

    包玺芳; 马跃忠; 王治道; 李仲香

    2012-01-01

    A wet purification method of refining metal tantalum powder was researched.After sodium reduction,the primary tantalum powder particles was washed by water and by mixed acid,and other impurities content,such as oxygen,carbon,Si,Fe,Ni and Cr in tantalum powder,were reduced significantly,the target arrived.%研究了一种金属钽粉的湿法提纯方法,即用钠还原后的原生钽粉粒子经水洗和混合酸酸洗,使钽粉中的O,C,Si及Fe,Ni,Cr等杂质质量分数明显降低,达到金属钽粉精炼提纯的目的.

  5. Diffusion of liquid uranium into solid tantalum foils up to 1350C

    Energy Technology Data Exchange (ETDEWEB)

    Kuznietz, M.; Livne, Z.; Cotler, C.

    1986-01-01

    The diffusion of liquid uranium into solid foils, 0.3 mm thick, was investigated in the temperature range 1160-1350C, for reaction times up to 20 h. The tantalum foils were immersed in liquid uranium contained in zirconia crucibles. Uranium was found to cover the tantalum foils and climb upwards in amounts rising with reaction time and temperature. A scanning electron microscope study with microanalysis by EDAX revealed a multilayer structure. On the tantalum-foil surfaces, exposed to liquid uranium, layers form progressively inwards, under the outer uranium layers, in the following sequence: a uranium-tantalum layer (with a U:Ta ratio between 40:60 and 60:40) forms at 1160 C and 1185 C, and disappears completely at 1255 C; a columnar tantalum layer (containing <1W/O U); an inner uranium layer (at 1210 C and above); an inner tantalum-grain layer with uranium along grain boundaries (above 1210 C). The growth of the recrystallized columnar tantalum layer is related to the penetration of uranium as liquid into the solid tantalum foil. Cracks in this layer at 1300 C and above cause tears and failures in the tantalum.

  6. High-brightness laser plasma soft X-ray source using a double-stream gas puff target irradiated with the Prague Asterix Laser System (PALS)

    Energy Technology Data Exchange (ETDEWEB)

    Fiedorowicz, H.; Bartnik, A.; Juha, L.; Jungwirth, K.; Kralikova, B.; Krasa, J.; Kubat, P.; Pfeifer, M.; Pina, L.; Prchal, P.; Rohlena, K.; Skala, J.; Ullschmied, J.; Horvath, M.; Wawer, J

    2004-01-14

    High brightness laser plasma soft X-ray source based on a recently developed double-stream gas puff target irradiated with 0.5 ns laser pulses with energies up to 700 J from the Prague Asterix Laser System (PALS) is presented. The gas puff target was created by pulsed injection of xenon into a hollow stream of helium using an electromagnetic valve system with the double-nozzle setup. Soft X-ray emission was measured using the transmission grating spectrograph coupled to a CCD camera and the calibrated silicon photodiodes. The absolute soft X-ray production was determined to be 160 J for 540 J of laser energy, giving the soft X-ray conversion efficiency of about 30%. The source has been used in initial experiments on soft X-ray ablation of organic polymers and elemental solids.

  7. Measurement of carbon deposit at to irradiate a target; Medicion del deposito de carbon al irradiar un blanco

    Energy Technology Data Exchange (ETDEWEB)

    Rosales M, P.; Aguilera R, E. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

    2004-07-01

    Backscattering data obtained when bombarding a thin target of {sup 12} C deposited on a thick substrate of Ta are analyzed, with a ion beam of {sup 12} C for high fluences and different energy between 9.85 and 13 MeV. A variation in the thickness of the target is observed and is found its correlation with the fluence in the target. (Author)

  8. Corrosion resistance of high-performance materials titanium, tantalum, zirconium

    CERN Document Server

    2012-01-01

    Corrosion resistance is the property of a material to resist corrosion attack in a particular aggressive environment. Although titanium, tantalum and zirconium are not noble metals, they are the best choice whenever high corrosion resistance is required. The exceptionally good corrosion resistance of these high–performance metals and their alloys results from the formation of a very stable, dense, highly adherent, and self–healing protective oxide film on the metal surface. This naturally occurring oxide layer prevents chemical attack of the underlying metal surface. This behavior also means, however, that high corrosion resistance can be expected only under neutral or oxidizing conditions. Under reducing conditions, a lower resistance must be reckoned with. Only very few inorganic and organic substances are able to attack titanium, tantalum or zirconium at ambient temperature. As the extraordinary corrosion resistance is coupled with an excellent formability and weldability these materials are very valua...

  9. [Preparation and optical properties of tantalum tungsten bronze].

    Science.gov (United States)

    Mu, Wan-jun; Xie, Xiang; Li, Xing-liang; Zhang, Rui; Lü, Kai; Wei, Hong-yuan

    2015-01-01

    Tantalum tungsten bronze(TaxWO3)nanowires were successfully synthesized via hydrothermal method using TaCl5 and Na2WO4 . 2H20 as raw materials. The morphology, crystal structure and optical properties of synthesized products were characterized by means of XRD, TEM, SEM, UV-Vis and Raman technologies. The XRD results showed that TaxWO3 nanowire exhibited hexagonal structure. By increasing the doping content, the cell parameter was kept increasing gradually till Ta/W= 0. 04, then it remained almost constant. The UV-Vis diffraction spectrum analysis showed that the absorption peaks redshifted, the band gap energy decreased with increasing the doping content. The Raman peaks moved with a downshift, and the peak gradually became broader, which further proved the influence of the tantalum doping for tungsten oxide. The reactions of decomposing liquid rhodamine B solution showed that the nanosized TaxWO3 had a high photo-catalytic activity.

  10. Antimicrobial activity of tantalum oxide coatings decorated with Ag nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Cao, Huiliang, E-mail: hlc@mail.sic.ac.cn; Meng, Fanhao; Liu, Xuanyong, E-mail: xyliu@mail.sic.ac.cn [State Key Laboratory of High Performance Ceramics and Superfine Microstructure, Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050 (China)

    2016-07-15

    Silver plasma immersion ion implantation was used to decorate silver nanoparticles (Ag NPs) on tantalum oxide (TO) coatings. The coatings acted against bacterial cells (Staphylococcus epidermidis) in the dark by disrupting their integrity. The action was independent of silver release and likely driven by the electron storage capability of the Schottky barriers established at the interfaces between Ag NPs and the TO support. Moreover, no apparent side effect on the adhesion and differentiation of rat bone mesenchymal stem cells was detected when using Ag NPs-modified TO coatings. These results demonstrate that decoration of tantalum oxide using Ag NPs could be a promising procedure for improving the antibacterial properties for orthopedic and dental implants.

  11. Plasticity In High Temperature Materials: Tantalum and Monazite

    Science.gov (United States)

    2014-03-12

    centered cu- bic tantalum, the methodology also demonstrated a relationship between dislocation mean free path length and GND density. A framework to...c) _ [110] x1 x2 F undeformed def orm ed ω3 x 1’ x 2’ (b) φ1=54.7° (110) [001] [110] _ x1 x2 S(1) S(2) S(3) _ _ (a) [110] [001] [110] (111)[101

  12. Analysis of bone ingrowth on a tantalum cup

    Directory of Open Access Journals (Sweden)

    D′Angelo F

    2008-01-01

    Full Text Available Background: Trabecular Metal (TM is a new highly porous material made of tantalum (Zimmer, Warsaw, Indiana, USA. Its three-dimensional structure is composed of a series of interconnected dodecahedron pores that are on average 550 μm in diameter. This size is considered optimal for bone ingrowth and is similar to trabecular bone. The elastic modulus of TM (3 GPa is more similar to that of cancellous (0,1-1,5 GPa or cortical (112-18 GPa bone and is significantly less similar to that of Titanium (110 GPa and Co-Cr alloys (220 GPa. These features enable bone apposition and remodeling. The purpose of the present study was to evaluate the histology of the bone-implant interface in a human specimen. Materials and Methods: A highly porous tantalum cup (Zimmer, Warsaw, Indiana, USA was removed for recurrent dislocations three years after implantation. In order to obtain a slice of the cup, two cuts were made on the centre using an Exakt cutting machine. Then the slice was embedded in a Technovit resin and a Hematoxylin-eosin stain was used to study the bone tissue. Bone ingrowth was calculated using a method based on simple calculations of planar geometry. Results: The histological evaluation of the periprosthetic tissues revealed a typical chronic inflammation with few particles of polyethylene that were birefringent using polarized light. The quantitative evaluation of bone ingrowth revealed that more than 95% of voids were filled with bone. Discussion: In the literature, a lot of studies focused on tantalum were carried on animal model. Up to now little information is available about the histology of the bone-tantalum interface in a human artificial joint. We had an opportunity to remove a well integrated cup hence this study. The histology confirmed the strong relationship between the structure of this material and bone. The morphometric analysis revealed a high percentage of bone ingrowth.

  13. Sodium Purification Device for Production of Tantalum Powder

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    In the process of tantalum powder production it requires pure sodium to reduce potassium fluotantalate, thus the design of a sodium purification device is improved, later it is built and commissioned. The device includes sodium transportation tank, storage tank, filter, cold trap, final storage tank, metering tank, regulating valve, argon purification system, electric control panel and instrument. Industrial purity sodium is purified, the impurities in the sodium were reduced to very

  14. Fabrication and characterisation of suspended microstructures of tantalum

    OpenAIRE

    Al-Masha-al, Asa'ad; Cheung, Rebecca; Bunting, Andrew; Mastropaolo, Enrico

    2016-01-01

    An investigation of the influence of deposition and post-fabrication processes on the final mechanical structure of tantalum beams is reported in the present study. The final deflection profiles of doubly supported beams made from compressive and tensile-stressed films have been studied experimentally. An optimum finite element model has been developed to predict the buckling behaviour of the doubly supported beams by considering the boundary conditions in the form of a compressive stress and...

  15. An analytic solution for calculating the beam intensity profiles useful to irradiate target volumes with bi-concave outlines

    Energy Technology Data Exchange (ETDEWEB)

    De Neve, W.; Derycke, S.; De Wagter, C. [Ghent Rijksuniversiteit (Belgium). Kliniek voor Radiotherapie en Kerngeneeskunde

    1995-12-01

    A heuristic planing procedure allowing to obtain a 3-dimensional conformal dose distribution in radiotherapy for target volumes with a bi-concave or multi-concave shape has been developed. The described method is tested on a phantom simulating a pelvic target, described by Brahme.

  16. Semimicrodetermination of combined tantalum and niobium with selenous acid

    Science.gov (United States)

    Grimaldi, F.S.; Schnepfe, M.

    1959-01-01

    Tantalum and niobium are separated and determined gravimetrically by precipitation with selenous acid from highly acidic solutions in the absence of complexing agents. Hydrogen peroxide is used in the preparation of the solution and later catalytically destroyed during digestion of the precipitate. From 0.2 to 30 mg., separately or in mixtures, of niobium or tantalum pentoxide can be separated from mixtures containing 100 mg. each of the oxides of scandium, yttrium, cerium, vanadium, molybdenum, iron, aluminum, tin, lead, and bismuth with a single precipitation; and from 30 mg. of titanium dioxide, and 50 mg. each of the oxides of antimony and thorium, when present separately, with three precipitations. At least 50 mg. of uranium(VI) oxide can be separated with a single precipitation when present alone; otherwise, three precipitations may be needed. Zirconium does not interfere when the tantalum and niobium contents of the sample are small, but in general, zirconium as well as tungsten interfere. The method is applied to the determination of the earth acids in tantaloniobate ores.

  17. Microstructures and phase transformations in interstitial alloys of tantalum

    Energy Technology Data Exchange (ETDEWEB)

    Dahmen, U.

    1979-01-01

    The analysis of microstructures, phases, and possible ordering of interstitial solute atoms is fundamental to an understanding of the properties of metal-interstitial alloys in general. As evidenced by the controversies on phase transformations in the particular system tantalum--carbon, our understanding of this class of alloys is inferior to our knowledge of substitutional metal alloys. An experimental clarification of these controversies in tantalum was made. Using advanced techniques of electron microscopy and ultrahigh vacuum techology, an understanding of the microstructures and phase transformations in dilute interstitial tantalum--carbon alloys is developed. Through a number of control experiments, the role and sources of interstitial contamination in the alloy preparation (and under operating conditions) are revealed. It is demonstrated that all previously published work on the dilute interstitially ordered phase Ta/sub 64/C can be explained consistently in terms of ordering of the interstitial contaminants oxygen and hydrogen, leading to the formation of the phases Ta/sub 12/O and Ta/sub 2/H.

  18. Application of pyrolysis to recycling organics from waste tantalum capacitors.

    Science.gov (United States)

    Niu, Bo; Chen, Zhenyang; Xu, Zhenming

    2017-08-05

    Tantalum capacitors (TCs) are widely used in electronic appliances. The rapid replacement of electronic products results in generating large amounts of waste TCs (WTCs). WTCs, rich in valuable tantalum, are considered as high quality tantalum resources for recycling. However, environmental pollution will be caused if the organics of WTCs were not properly disposed. Therefore, effectively recycling the organics of WTCs is significant for recovering the valuable parts. This study proposed an argon (Ar) pyrolysis process to recycle the organics from WTCs. The organic decomposition kinetic was first analyzed by thermogravimetry. The results showed that the organics were decomposed in two major steps and the average activation energy was calculated to 234kJ/mol. Then, the suitable pyrolysis parameters were determined as 550°C, 30min and 100ml/min. The organics were effectively decomposed and converted to oils (mainly contained phenol homologs and benzene homologs) and gases (some hydrocarbon). These pyrolysis products could be reutilized as energy sources. Moreover, based on the products and bond energy theory, the pyrolysis mechanisms of the organics were also discussed. Finally, a reasonable technological process for products utilization was presented. This study contributes to the efficient recycling the organics before valuable material recovery from WTCs. Copyright © 2017 Elsevier B.V. All rights reserved.

  19. Leakage Currents and Gas Generation in Advanced Wet Tantalum Capacitors

    Science.gov (United States)

    Teverovsky, Alexander

    2015-01-01

    Currently, military grade, established reliability wet tantalum capacitors are among the most reliable parts used for space applications. This has been achieved over the years by extensive testing and improvements in design and materials. However, a rapid insertion of new types of advanced, high volumetric efficiency capacitors in space systems without proper testing and analysis of degradation mechanisms might increase risks of failures. The specifics of leakage currents in wet electrolytic capacitors is that the conduction process is associated with electrolysis of electrolyte and gas generation resulting in building up of internal gas pressure in the parts. The risk associated with excessive leakage currents and increased pressure is greater for high value advanced wet tantalum capacitors, but it has not been properly evaluated yet. In this work, in Part I, leakages currents in various types of tantalum capacitors have been analyzed in a wide range of voltages, temperatures, and time under bias. Gas generation and the level of internal pressure have been calculated in Part II for different case sizes and different hermeticity leak rates to assess maximal allowable leakage currents. Effects related to electrolyte penetration to the glass seal area have been studied and the possibility of failures analyzed in Part III. Recommendations for screening and qualification to reduce risks of failures have been suggested.

  20. Random Vibration Testing of Advanced Wet Tantalum Capacitors

    Science.gov (United States)

    Teverovsky, Alexander

    2015-01-01

    Advanced wet tantalum capacitors allow for improved performance of power supply systems along with substantial reduction of size and weight of the systems that is especially beneficial for space electronics. Due to launch-related stresses, acceptance testing of all space systems includes random vibration test (RVT). However, many types of advanced wet tantalum capacitors cannot pass consistently RVT at conditions specified in MIL-PRF-39006, which impedes their use in space projects. This requires a closer look at the existing requirements, modes and mechanisms of failures, specifics of test conditions, and acceptance criteria. In this work, different lots of advanced wet tantalum capacitors from four manufacturers have been tested at step stress random vibration conditions while their currents were monitored before, during, and after the testing. It has been shown that the robustness of the parts and their reliability are mostly due to effective self-healing processes and limited current spiking or minor scintillations caused by RVT do not increase the risk of failures during operation. A simple model for scintillations events has been used to simulate current spiking during RVT and optimize test conditions. The significance of scintillations and possible effects of gas generation have been discussed and test acceptance criteria for limited current spiking have been suggested.

  1. Mechanism of pain relief by low-power infrared irradiation: ATP is an IR-target molecule in nociceptive neurons.

    Science.gov (United States)

    Yachnev, Igor L; Plakhova, Vera B; Podzorova, Svetlana A; Shelykh, Tatiana N; Rogachevsky, Ilya V; Krylov, Boris V

    2012-01-01

    Effects of infrared (IR) radiation generated by a low-power CO2-laser on the membrane of cultured dissociated nociceptive neurons of newborn rat spinal ganglia were investigated using the whole-cell patch-clamp method. Low-power IR radiation diminished the voltage sensitivity of activation gating machinery of slow sodium channels (Na(v)1.8). Ouabain known to block both transducer and pumping functions of Na+,K+-ATPase eliminated IR irradiation effects. The molecular mechanism of interaction of CO2-laser radiation with sensory membrane was proposed. The primary event of this interaction is the process of energy absorption by ATP molecules. The transfer of vibrational energy from Na+,K+- ATPase-bound and vibrationally excited ATP molecules to Na+,K+-ATPase activates this enzyme and converts it into a signal transducer. This effect leads to a decrease in the voltage sensitivity of Na(v)1.8 channels. The effect of IR-radiation was elucidated by the combined application of a very sensitive patch-clamp method and an optical facility with a controlled CO2-laser. As a result, the mechanism of interaction of non-thermal low-power IR radiation with the nociceptive neuron membrane is suggested.

  2. DISSOLUTION OF FISSILE MATERIALS CONTAINING TANTALUM METAL

    Energy Technology Data Exchange (ETDEWEB)

    Rudisill, T; Mark Crowder, M; Michael Bronikowski, M

    2007-05-29

    The dissolution of composite materials containing plutonium (Pu) and tantalum (Ta) metals is currently performed in Phase I of the HB-Line facility. The conditions for the present flowsheet are the dissolution of 500 g of Pu metal in the 15 L dissolver using a 4 M nitric acid (HNO{sub 3}) solution containing 0.2 M potassium fluoride (KF) at 95 C for 4-6 h.[1] The Ta metal, which is essentially insoluble in HNO{sub 3}/fluoride solutions, is rinsed with process water to remove residual acid, and then burned to destroy classified information. During the initial dissolution campaign, the total mass of Pu and Ta in the dissolver charge was limited to nominally 300 g. The reduced amount of Pu in the dissolver charge coupled with significant evaporation of solution during processing of several dissolver charges resulted in the precipitation of a fluoride salt contain Pu. Dissolution of the salt required the addition of aluminum nitrate (Al(NO{sub 3}){sub 3}) and a subsequent undesired 4 h heating cycle. As a result of this issue, HB-Line Engineering requested the Savannah River National Laboratory (SRNL) to optimize the dissolution flowsheet to reduce the cycle time, reduce the risk of precipitating solids, and obtain hydrogen (H{sub 2}) generation data at lower fluoride concentrations.[2] Using samples of the Pu/Ta composite material, we performed three experiments to demonstrate the dissolution of the Pu metal using HNO{sub 3} solutions containing 0.15 and 0.175 M KF. When 0.15 M KF was used in the dissolving solution, 95.5% of the Pu in the sample dissolved in approximately 6 h. The undissolved material included a small amount of Pu metal and plutonium oxide (PuO{sub 2}) solids. Complete dissolution of the metal would have likely occurred if the dissolution time had been extended. This assumption is based on the steady increase in the Pu concentration observed during the last several hours of the experiment. We attribute the formation of PuO{sub 2} to the complexation

  3. Measurements of neutron spectrum from stopping-length target irradiated by several tens-MeV/u particles

    Energy Technology Data Exchange (ETDEWEB)

    Meigo, Shin-ichiro; Takada, Hiroshi; Nakashima, Hiroshi; Sasa, Toshinobu [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Tanaka, Susumu; Shin, Kazuo; Ono, Shinji

    1997-03-01

    Using a Time-of-Flight technique, we have measured neutron spectra from stopping-length targets bombarded with 68-MeV protons and 100-MeV {alpha}-particles. The measured spectra were used to validate the results calculated by the Quantum Molecular Dynamics (QMD) plus Statistical Decay Model (SDM). The results of QMD plus SDM code agreed fairly well with the experimental data for the light target. On the other hand, the QMD plus SDM gives a larger value than the experimental for the heavy target. (author)

  4. Role of Hypoxia-inducible factor-1 and its target genes in human lung adenocarcinoma cells after photon- versus carbon ion irradiation; Expression HIF-1-abhaengiger Gene in humanen Lungenadenokarzinom (A549)-Zellen und deren Regulation nach Photonen- und Schwerionenbestrahlung

    Energy Technology Data Exchange (ETDEWEB)

    Bill, Verena Maria

    2013-11-26

    Exposed to hypoxia tumor cells are notably resistant to photon irradiation. The hypoxiainducible transcription factor 1α (HIF-1α) seems to play a fundamental role in this resistance, while its role after heavy-ion beam remains unknown. The intention of this study was to determine how A549-cells (non-small-cell lung carcinoma) react in different oxygenation states after irradiation with photons or heavy ions, particularly in regards to their expression of HIF-1 target genes. Resistance of hypoxic A549 cells after photon irradiation was documented by cellular and clonogenic survival. In contrast, cellular survival after heavy-ion irradiation in hypoxic cells was not elevated to normoxic cells. Among the oxygen dependent regulation of HIF-1 target genes, gene expression analyses showed an increased expression of GLUT-1, LDH-A, PDK-1 and VEGF after photon irradiation but not after heavy-ion irradiation after 48 hours in normoxic cells. As expected, CDKN1A as inhibitor of cell cycle progression showed higher expression after both radiation forms; interestingly CDKN1A was also in an oxygen dependent manner lightly upregulated. In western blot analyses we demonstrated a significant increase of HIF-1 and GLUT-1 caused by hypoxia, but only a tendency of increased protein level in hypoxia after photon irradiation and no changes after heavy-ion irradiation. Significantly higher protein level of secreted VEGF-A could be measured 72 hours after photon irradiation in normoxic cells by ELISA analyses. Controversially discussed, I could not detect an association between HIF-1 and SCF or Trx-1 in A549-cells in this study. Whereas Trx-1-expression was neither influenced by changed oxygen partial pressure nor irradiation, I could show increased SCF mRNA by quantitative Real Time-PCR and secreted protein level by ELISA after photon irradiation independent of oxygen state. In summary, this study showed that HIF-1 and its target genes (GLUT-1, LDHA; PDK, VEGF) and also SCF was

  5. Radiochemical determination of {sup 129}I and {sup 36}Cl in MEGAPIE, a proton irradiated lead-bismuth eutectic spallation target

    Energy Technology Data Exchange (ETDEWEB)

    Hammer-Rotzler, Bernadette; Tuerler, Andreas [Paul Scherrer Institut (PSI), Villigen (Switzerland); Bern Univ. (Switzerland); Neuhausen, Joerg; Boutellier, Viktor; Wohlmuther, Michael; Schumann, Dorothea [Paul Scherrer Institut (PSI), Villigen (Switzerland); Vockenhuber, Christof [ETH Zurich (Switzerland). Lab. of Ion Beam Physics

    2015-07-01

    The concentrations of the long-lived nuclear reaction products {sup 129}I and {sup 36}Cl have been measured in samples from the MEGAPIE liquid metal spallation target. Samples from the bulk target material (lead-bismuth eutectic, LBE), from the interface of the metal free surface with the cover gas, from LBE/steel interfaces and from noble metal absorber foils installed in the cover gas system were analysed using Accelerator Mass Spectrometry at the Laboratory of Ion beam Physics at ETH Zuerich. The major part of {sup 129}I and {sup 36}Cl was found accumulated on the interfaces, particularly at the interface of LBE and the steel walls of the target container, while bulk LBE samples contain only a minor fraction of these nuclides. Both nuclides were also detected on the absorber foils to a certain extent (<< 1% of the total amount). The latter number is negligible concerning the radio-hazard of the irradiated target material; however it indicates a certain affinity of the absorber foils for halogens, thus proving the principle of using noble metal foils for catching these volatile radionuclides. The total amounts of {sup 129}I and {sup 36}Cl in the target were estimated from the analytical data by averaging within the different groups of samples and summing up these averages over the total target. This estimation could account for about half of the amount of {sup 129}I and {sup 36}Cl predicted to be produced using nuclear physics modelling codes for both nuclides. The significance of the results and the associated uncertainties are discussed.

  6. Growth characteristics and functional changes in rat chondrocytes cultured in porous tantalum in vitro

    Directory of Open Access Journals (Sweden)

    Ling ZHANG

    2014-08-01

    Full Text Available Objective To evaluate the growth characteristics and functional changes in rat chondrocytes cultured in porous tantalum in vitro. Methods The chondrocytes isolated from cartilage of 3-week old SD rats were cultured in vitro, then the 2nd passage cells were identified and implanted in porous tantalum scaffolds with a density of 1×106 cells/ml. The morphological characteristics of the chondrocytes cultured in porous tantalum were observed under inverted microscope, scanning electron microscope (SEM and transmission electron microscope (TEM, and the content of glycosaminoglycan (GAG in the chondrocytes was measured by chromatometry. Results The harvested cells were identified as chondrocytes by type Ⅱ collagen immunocytochemical staining, toluidine blue staining and safranin-O staining. Many chondrocytes adhering to the edge of porous tantalum were found by inverted microscope. Observation under SEM showed that chondrocytes spread well on the surface and distributed in the holes of porous tantalum, and they proliferated and secreted some extracellular matrixes. TEM observation showed that the ultrastructure of chondrocytes cultured in porous tantalum was similar to that of normal chondrocytes. Chromatometry determination showed that the chondrocytes in porous tantalum could secrete GAG continuously. Conclusion Porous tantalum is shown to have a satisfactory biocompatibility with chondrocytes in vitro, and may be used as a scaffold for cartilage tissue engineering. DOI: 10.11855/j.issn.0577-7402.2014.06.08

  7. Tantalum Coating of Steel, Copper, Aluminum, and Titanium by Thermal Chemical Vapor Deposition (CVD)

    DEFF Research Database (Denmark)

    Christensen, Erik; Bjerrum, Niels

    1998-01-01

    Tantalum coatings ranging from 0.5 to 120 mm has been deposited by CVD at 625-1000 C using tantalum pentachloride as precursor. Deposition rates range from 1 to 80mm/h and an activation energy of 103 kJ/mole is calculated. Well adhering deposits has been obtained on stainless steel, carbon steels...

  8. Kinetic Study of the Chemical Vapor Deposition of Tantalum in Long Narrow Channels

    DEFF Research Database (Denmark)

    Mugabi, James Atwoki; Eriksen, Søren; Petrushina, Irina

    2016-01-01

    A kinetic study of the chemical vapor deposition of tantalum in long narrow channels is done to optimize the industrial process for the manufacture of tantalum coated plate heat exchangers. The developed model fits well at temperatures between 750 and 850 °C, and in the pressure range of25–990 mb...

  9. Joint Experiments on X-ray/Particle Emission from Plasmas Produced by Laser Irradiating Nano Structured Targets

    Science.gov (United States)

    Hegazy, H.; Allam, S. H.; Chaurasia, S.; Dhareshwar, L.; El-Sherbini, Th. M.; Kunze, H.-J.; Mank, G.; McDaniel, D. H.; Rosinski, M.; Ryc, L.; Stewart, B.; Wolowski, J.; Abd El-Ghany, H.; Abd El-Latif, G.; Abd El-Rahim, F. M.; Bedrane, Z.; Diab, F.; Farrag, A.; Hedwig, R.; Helal, A.; Pardede, M.; Refaie, A.; Sharkawy, H.; El-khatim, A., Sir

    2008-04-01

    The 1st Joint (Host Laboratory) Experiment on laser plasma involving more than twenty scientists from eight countries has been carried out at the Laser and New Materials Laboratory, Faculty of Science, Cairo University, Egypt. It was co-ordinated by the International Atomic Energy Agency (IAEA) and supported through the IAEA and the ICTP (International Centre for Theoretical Physics, Trieste). The main experimental programme was aimed at characterising the possible enhancement of x-ray and particle emission from plasmas produced by laser incidence on nano-structured targets. Laser beams at 1.064 μm of 250 mJ and 532 nm of 165 mJ focused at the target surface using a nanosecond laser type Quantel were used in the present study. In the present experiments nano-copper structures evaporated onto copper bulk disks and nano-gold structures evaporated onto gold ones were used. The thickness of the nano-materials on their bulk material was 1 μm. An ion collector and x-ray semiconductor diode were used to study the ion and x-ray emission, respectively. Both were positioned at the same port at 90° with respect to the target surface and at 90 cm from the surface in the case of the ion collector and 55 cm in the case of the x-ray detector. These experiments were performed at vacuum pressures of (5—8)×10-6 mbar. Comparison of both studies in the case of nano structured targets and bulk targets were performed at different laser fluencies (1×109-1×1012 W/cm2) on the target. A 20% increase of the X-ray emission for nano gold with respect to bulk gold was observed, however, the x-ray emission in the of nano copper and copper was the same.

  10. A TPD and AR based comparison of accelerator neutron irradiation fields between (7)Li and W targets for BNCT.

    Science.gov (United States)

    Tanaka, Kenichi; Endo, Satoru; Yonai, Shunsuke; Baba, Mamoru; Hoshi, Masaharu

    2014-06-01

    The characteristics of moderator assembly dimension was investigated for the usage of (7)Li(p,n) neutrons by 2.3-2.8MeV protons and W(p,n) neutrons by 50MeV protons. The indexes were the treatable protocol depth (TPD) and advantage depth (AD). Consequently, a configuration for W target with the Fe filter, Fluental moderator, Pb reflector showed the TPD of 5.8cm and AD of 9.3cm. Comparable indexes were found for the Li target in a geometry with the MgF2 moderator and Teflon reflector.

  11. The role of repair in the survival of mammalian cells from heavy ion irradiation - Approximation to the ideal case of target theory

    Science.gov (United States)

    Lett, J. T.; Cox, A. B.; Story, M. D.

    1989-01-01

    Experiments are discussed in which the cell-cycle dependency of the repair deficiency of the S/S variant of the L5178Y murine leukemic lymphoblast was examined by treatment with the heavy ions, Ne-20, Si-28, Ar-40, Fe-56, and Nb-93. Evidence from those studies provide support for the notion that as the linear energy transfer of the incident radiation increases the ability of the S/S cell to repair radiation damage decreases until it is eliminated around 500 keV/micron. In the region of the latter linear energy transfer value, the behavior of the S/S cell approximates the ideal case of target theory where post-irradiation metabolism does not influence cell survival.

  12. Experimental benchmark for an improved simulation of absolute soft-x-ray emission from polystyrene targets irradiated with the Nike laser.

    Science.gov (United States)

    Weaver, J L; Busquet, M; Colombant, D G; Mostovych, A N; Feldman, U; Klapisch, M; Seely, J F; Brown, C; Holland, G

    2005-02-04

    Absolutely calibrated, time-resolved spectral intensity measurements of soft-x-ray emission (hnu approximately 0.1-1.0 keV) from laser-irradiated polystyrene targets are compared to radiation-hydrodynamic simulations that include our new postprocessor, Virtual Spectro. This new capability allows a unified, detailed treatment of atomic physics and radiative transfer in nonlocal thermodynamic equilibrium conditions for simple spectra from low-Z materials as well as complex spectra from high-Z materials. The excellent agreement (within a factor of approximately 1.5) demonstrates the powerful predictive capability of the codes for the complex conditions in the ablating plasma. A comparison to data with high spectral resolution (E/deltaE approximately 1000) emphasizes the importance of including radiation coupling in the quantitative simulation of emission spectra.

  13. Protection of normal brain cells from γ-irradiation-induced apoptosis by a mitochondria-targeted triphenyl-phosphonium-nitroxide: a possible utility in glioblastoma therapy.

    Science.gov (United States)

    Huang, Zhentai; Jiang, Jianfei; Belikova, Natalia A; Stoyanovsky, Detcho A; Kagan, Valerian E; Mintz, Arlan H

    2010-10-01

    Glioblastoma multiforme is the most frequent and aggressive primary brain tumor. A strong rationale to identify innovative approaches to treat these tumors is required since treatment failures result in local recurrences and median survivals range from 9 to 12 months. Glioma cells are reported to have less mitochondrial content compared to adjacent normal brain cells. Based on this difference, we suggest a new strategy, utilizing protection of normal brain cells by mitochondria-targeted electron scavengers and antioxidants-nitroxides-thus allowing for the escalation of the radiation doses. In this paper, we report that a conjugate of nitroxide with a hydrophobic cation, triphenyl-phosphonium (TPEY-Tempo), significantly protected brain endothelial cells from γ-irradiation-induced apoptosis while radiosensitizing brain tumor cells. Thus, TPEY-Tempo may be a promising adjunct in the treatment of glioblastoma with the potential to not only prolong survival but also to maintain quality of life and reduce treatment toxicity.

  14. Niobium sputtered Havar foils for the high-power production of reactive [18F]fluoride by proton irradiation of [18O]H2O targets.

    Science.gov (United States)

    Wilson, J S; Avila-Rodriguez, M A; Johnson, R R; Zyuzin, A; McQuarrie, S A

    2008-05-01

    Niobium sputtered Havar entrance foils were used for the production of reactive [(18)F]fluoride by proton irradiation of [(18)O]H(2)O targets under pressurized conditions. The synthesis yield in the routine production of 2-[(18)F]fluoro-2-deoxy-glucose (FDG) was used as an indicative parameter of the reactivity of (18)F. The yield of FDG obtained with (18)F produced in a target with Havar foil was used as a baseline. No statistically significant difference was found in the saturated yields of (18)F when using Havar or Havar-Nb sputtered entrance foils. However, the amount of long-lived radionuclidic impurities decreased more than 10-fold using the Havar-Nb entrance foil. The average decay corrected synthesis yield of FDG, evaluated over a period of more than 2 years, was found to be approximately 5% higher when using a Havar-Nb entrance foil and a marked improvement on the FDG yield consistency was noted. In addition, the frequency of target rebuilding was greatly diminished when using the Nb sputtered entrance foil.

  15. Coupling of morphology to surface transport in ion-beam-irradiated surfaces: normal incidence and rotating targets

    Energy Technology Data Exchange (ETDEWEB)

    Munoz-Garcia, Javier [Grupo Interdisciplinar de Sistemas Complejos (GISC) and School of Mathematical Sciences and Complex and Adaptive Systems Laboratory, University College Dublin, Belfield, Dublin 4 (Ireland); Cuerno, Rodolfo [Departamento de Matematicas and GISC, Universidad Carlos III de Madrid, Avenida de la Universidad 30, E-28911 Leganes (Spain); Castro, Mario [GISC and Grupo de Dinamica No Lineal (DNL), Escuela Tecnica Superior de IngenierIa (ICAI), Universidad Pontificia Comillas de Madrid, E-28015 Madrid (Spain)], E-mail: javiermunozgarcia@gmail.com, E-mail: cuerno@math.uc3m.es, E-mail: mariocastro73@gmail.com

    2009-06-03

    Continuum models have proved their applicability to describe nanopatterns produced by ion-beam sputtering of amorphous or amorphizable targets at low and medium energies. Here we pursue the recently introduced 'hydrodynamic approach' in the cases of bombardment at normal incidence, or of oblique incidence onto rotating targets, known to lead to self-organized arrangements of nanodots. Our approach stresses the dynamical roles of material (defect) transport at the target surface and of local redeposition. By applying results previously derived for arbitrary angles of incidence, we derive effective evolution equations for these geometries of incidence, which are then numerically studied. Moreover, we show that within our model these equations are identical (albeit with different coefficients) in both cases, provided surface tension is isotropic in the target. We thus account for the common dynamics for both types of incidence conditions, namely formation of dots with short-range order and long-wavelength disorder, and an intermediate coarsening of dot features that improves the local order of the patterns. We provide for the first time approximate analytical predictions for the dependence of stationary dot features (amplitude and wavelength) on phenomenological parameters, that improve upon previous linear estimates. Finally, our theoretical results are discussed in terms of experimental data.

  16. TARGET:?

    National Research Council Canada - National Science Library

    James M Acton

    2014-01-01

      By 2003. as military planners had become worried that the country's long-range conventional weapons, such as cruise missiles, might be too slow to reach hypothetical distant targets that needed to be struck urgently...

  17. Synthesis, characterization and photo catalytic studies of the composites by tantalum oxide and zinc oxide nanorods

    Science.gov (United States)

    Chennakesavulu, K.; Reddy, M. Madhusudhana; Reddy, G. Ramanjaneya; Rabel, A. M.; Brijitta, J.; Vinita, V.; Sasipraba, T.; Sreeramulu, J.

    2015-07-01

    In-situ synthesis of ZnO:Ta2O5 composites in basic medium by using tantalum chloride and zinc chloride as precursors. The prepared composites were characterized by Fourier Transform Infrared spectroscopy (FTIR), confocal Raman spectroscopy, diffuse reflectance UV-Vis spectrophotometer (DRS), X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET) method, N2-sorption isotherms, Thermo Gravimetric Analysis (TGA), High Resolution Transmission Electron Microscope (HRTEM), X-ray Photoelectron Spectroscopy (XPS), and Field Emission Scanning Electron Microscopy (FESEM/EDS). The composite materials were used as photocatalyst in the degradation Rhodamine-B (RhB) dye under visible light irradiation. The catalytic activity and removal percentage of the dye was determined by the spectrophotometric method. This indicates the percentage of degradation was more for the ZnO:Ta2O5 composites. The kinetic parameter obeys pseudo-first order reaction. It may be due to fixed amount the catalysts and concentration of dye solution. The catalytic activity of the recycled ZnO:Ta2O5 catalyst was compared with fresh catalyst.

  18. Spark plasma sintering of tantalum carbide and graphene reinforced tantalum carbide composites

    Science.gov (United States)

    Kalluri, Ajith Kumar

    Tantalum carbide (TaC), an ultra-high temperature ceramic (UHTC), is well known for its exceptional properties such as high hardness (15-19 GPa), melting point (3950 °C), elastic modulus (537 GPa), chemical resistance, and thermal shock resistance. To make TaC to be the future material for hypersonic vehicles, it is required to improve its thermal conductivity, strength, and fracture toughness. Researchers have previously reinforced TaC ceramic with carbides of silicon and boron as well as carbon nanotubes (CNTs), however, these reinforcements either undergo chemical changes or induce defects in the matrix during processing. In addition, these reinforcements exhibit a very minimal improvement in the properties. In the present work, we attempted to improve TaC fracture toughness by reinforcing with graphene nano-platelets (GNPs) and processing through spark plasma sintering at high temperature of 2000 °C, pressure of 70 MPa, and soaking time of 10 min. In addition, we investigated the active densification mechanism during SPS of TaC powder and the effect of ball milling time on mechanical properties of sintered TaC. A relative density of >96% was achieved using SPS of monolithic TaC (<3 μm). Ball milling improved the sintering kinetics and improved the mechanical properties (microhardness, bi-axial flexural strength, and indentation fracture toughness). Activation energy (100 kJ/mol) and stress exponent (1.2) were obtained using the analytical model developed for power-law creep. Grain boundary sliding is proposed as active densification mechanism based on these calculations. Reinforcing GNPs (2-6 vol.% ) in the TaC matrix improved relative density (99.8% for TaC-6 vol.% GNP). Also ˜150% and ˜180% increase in flexural strength and fracture toughness, respectively, was observed for TaC-6 vol.% GNP composite. The significant improvement in these properties is attributed to improved densification and toughening mechanisms such as sheet pull-out and crack

  19. A comparative study of Rayleigh-Taylor and Richtmyer-Meshkov instabilities in 2D and 3D in tantalum

    Science.gov (United States)

    Sternberger, Z.; Maddox, B. R.; Opachich, Y. P.; Wehrenberg, C. E.; Kraus, R. G.; Remington, B. A.; Randall, G. C.; Farrell, M.; Ravichandran, G.

    2017-01-01

    Driving a shock wave through the interface between two materials with different densities can result in the Richtmyer-Meshkov or Rayleigh-Taylor instability and initial perturbations at the interface will grow. If the shock wave is sufficiently strong, the instability will lead to plastic flow at the interface. Material strength will reduce the amount of plastic flow and suppress growth. While such instabilities have been investigated in 2D, no studies of this phenomena have been performed in 3D on materials with strength. Initial perturbations to seed the hydrodynamic instability were coined into tantalum recovery targets. Two types of perturbations were used, two dimensional (2D) perturbations (hill and valley) and three-dimensional (3D) perturbations (egg crate pattern). The targets were subjected to dynamic loading using the Janus laser at the Jupiter Laser Facility. Shock pressures ranged from 50 GPa up to 150 GPa and were calibrated using VISAR drive targets.

  20. Experimental Study on Fast Electrons Transport in Ultra-intense Laser Irradiated Solid Targets by Transition Radiation

    Science.gov (United States)

    Zhijian, Zheng; Guangcan, Wang; Yuqiu, Gu

    2008-11-01

    The experiment was performed with SILEX laser facility(Ti-saphhire) at LFRC in China. The SILEX parameter: wavelength 0.8μm, duration 35fs, output power 280TW, contrast 5*105, The focal spot φ10μm(F/1.7), intensity on target surface 1*10^19W/cm^2(F/3). The main diagnostic equipments are the electron spectrometer, OMA spectrometer, optical streak camera. Some experimental results are given: The spectrum of optical emission from rear surface is rather narrow around some particular frequencies(1φ, 2φ, 3φ), We ascribe and confirm that the spike-like spectral line that is coherent transition radiation; The coherent light is also seen on time-integrated image with ring-patter due to Weibel instability of the fast electron transport; Obtained experimental cure of target thickness vs OTR image intensity is relative to mean free path of fast electron; The measuring optical transition radiation(OTR) duration of 171ps much longer than 1ps duration of fast electron transport target, the possible explanation is that the OTR duration to be determined magnetic diffusion time.

  1. Volatile elements production rates in a 1.4 Gev proton-irradiated molten lead-bismuth target

    CERN Document Server

    Zanini, L; Everaerts, P; Fallot, M; Franberg, H; Gröschel, F; Jost, C; Kirchner, T; Kojima, Y; Köster, U; Lebenhaft, J; Manfrina, E; Pitcher, E J; Ravn, H L; Tall, Y; Wagner, W; Wohlmuther, M

    2005-01-01

    Production rates of volatile elements following spallation reaction of 1.4 GeV protons on a liquid Pb/Bi target have been measured. The experiment was performed at the ISOLDE facility at CERN. These data are of interest for the developments of targets for accelerator driven systems such as MEGAPIE. Additional data have been taken on a liquid Pb target. Calculations were performed using the FLUKA and MCNPX Monte Carlo codes coupled with the evolution codes ORIHET3 and FISPACT using different options for the intra-nuclear cascades and evaporation models. Preliminary results from the data analysis show good comparison with calculations for Hg and for noble gases. For other elements such as I it is apparent that only a fraction of the produced isotopes is released. The agreement with the experimental data varies depending on the model combination used. The best results are obtained using MCNPX with the INCL4/ABLA models and with FLUKA. Discrepancies are found for some isotopes produced by fission using the MCNPX ...

  2. Hydrous Tantalum Phosphates for Ion Exchange Purposes: A Systematic Study

    Directory of Open Access Journals (Sweden)

    M.L.C.P.da Silva

    2002-03-01

    Full Text Available This work describes two methods of preparation of hydrous tantalum phosphates and their characterization as ion exchangers. The hydrous metallic phosphate compounds were chemically and physically characterized by thermal gravimetric analysis, X-ray diffractometry and surface area measurements. By the first method, tantalum phosphate was prepared by alkaline fusion of Ta2O5 with an excess of K2CO3, followed by lixiviation of the tantalate fusion product with hot water, and precipitation with diluted H3PO4. Preparation II was performed using metallic Ta dissolved in concentrated HF/HNO3 acidic mixture followed by hydrolysis of fluortantalic acid intermediary and precipitation with diluted H3PO4. Both freshly prepared materials (I and II were exaustively refluxed with concentrated H3PO4, in its boiling point temperature, resulting respectively in Ta2O5. 2.1 H2O, (IR and Ta2O5. 1.3 H2O, (IIR. Characterization of the prepared products have presented the following values: surface area of 108.27 ± 2.80; 220.14 ± 2.67; 117.07 ± 5.25 and 141.61 ± 0.27 m².g-1 respectively for I, IR, II and IIR. All these materials were amorphous. The ion exchange behavior for all four hydrous tantalum phosphates was studied using Na+, K+ and Ba+2 as the exchanged species. The values for typical ion exchange capacity were 1.64; 1.23; 1.47 and 1.01 miliequivalent.g-1, respectively for I, IR, II and IIR products.

  3. Spallation Neutron Spectrum on a Massive Lead/Paraffin Target Irradiated with 1 GeV Protons

    CERN Document Server

    Adam, J; Barashenkov, V S; Brandt, R; Golovatiouk, V M; Kalinnikov, V G; Katovsky, K; Krivopustov, M I; Kumar, V; Kumawat, H; Odoj, R; Pronskikh, V S; Solnyshkin, A A; Stegailov, V I; Tsoupko-Sitnikov, V M; Westmeier, W

    2004-01-01

    The spectra of gamma-ray emitted by decaying residual nuclei, produced by spallation neutrons with (n, xn), (n,xnyp), (n,p), (n,gamma) reactions in activation threshold detectors - namely, ^{209}Bi, ^{197}Au, ^{59}Co, ^{115}In, ^{232}Th, were measured in the Laboratory of Nuclear Problems (LNP), JINR, Dubna, Russia. Spallation neutrons were generated by bombarding a 20 cm long cylindrical lead target, 8 cm in diameter, surrounded by a 6 cm thick layer of paraffin moderator, with a 1 GeV proton beam from the Nuclotron accelerator. Reaction rates and spallation neutron spectrum were measured and compared with CASCADE code calculations.

  4. 225Ac and 223Ra production via 800 MeV proton irradiation of natural thorium targets.

    Science.gov (United States)

    Weidner, J W; Mashnik, S G; John, K D; Ballard, B; Birnbaum, E R; Bitteker, L J; Couture, A; Fassbender, M E; Goff, G S; Gritzo, R; Hemez, F M; Runde, W; Ullmann, J L; Wolfsberg, L E; Nortier, F M

    2012-11-01

    Cross sections for the formation of (225,227)Ac, (223,225)Ra, and (227)Th via the proton bombardment of natural thorium targets were measured at a nominal proton energy of 800 MeV. No earlier experimental cross section data for the production of (223,225)Ra, (227)Ac and (227)Th by this method were found in the literature. A comparison of theoretical predictions with the experimental data shows agreement within a factor of two. Results indicate that accelerator-based production of (225)Ac and (223)Ra is a viable production method.

  5. Separation of no-carrier-added Cu-64 from a proton irradiated Ni-64 enriched nickel target

    DEFF Research Database (Denmark)

    Hou, Xiaolin; Jacobsen, U.; Jørgensen, J.C.

    2002-01-01

    are then absorbed on an anion exchange column. Co and Ni are removed from the column by eluting with 72% ethanol-0.3mol/l HCl. Finally, the Cu-64 is eluted with water. For separating Ni from Co isotopes and recovering the Ni-64 target, the eluate of 72% ethanol-0.3 mol/l HCl is evaporated to dryness, the residue...... a cyclotron. The decontamination of Co in Cu fraction is higher than 99% and recoveries of Cu-64 and Ni-64 are higher than 95%. (C) 2002 Elsevier Science Ltd. All rights reserved....

  6. Hot surface ionic line emission and cold K-inner shell emission from petawatt-laser irradiated Cu foil targets

    Energy Technology Data Exchange (ETDEWEB)

    Theobald, W; Akli, K; Clarke, R; Delettrez, J A; Freeman, R R; Glenzer, S; Green, J; Gregori, G; Heathcote, R; Izumi, N; King, J A; Koch, J A; Kuba, J; Lancaster, K; MacKinnon, A J; Key, M; Mileham, C; Myatt, J; Neely, D; Norreys, P A; Park, H; Pasely, J; Patel, P; Regan, S P; Sawada, H; Shepherd, R; Snavely, R; Stephens, R B; Stoeckl, C; Storm, M; Zhang, B; Sangster, T C

    2005-12-13

    A hot, T{sub e} {approx} 2- to 3-keV surface plasma was observed in the interaction of a 0.7-ps petawatt laser beam with solid copper-foil targets at intensities >10{sup 20} W/cm{sup 2}. Copper K-shell spectra were measured in the range of 8 to 9 keV using a single-photon-counting x-ray CCD camera. In addition to K{sub {alpha}} and K{sub {beta}} inner-shell lines, the emission contained the Cu He{sub {alpha}} and Ly{sub {alpha}} lines, allowing the temperature to be inferred. These lines have not been observed previously with ultrafast laser pulses. For intensities less than 3 x 10{sup 18} W/cm{sup 2}, only the K{sub {alpha}} and K{sub {beta}} inner-shell emissions are detected. Measurements of the absolute K{sub {alpha}} yield as a function of the laser intensity are in agreement with a model that includes refluxing and confinement of the suprathermal electrons in the target volume.

  7. Direct electroplating of copper on tantalum from ionic liquids in high vacuum: origin of the tantalum oxide layer.

    Science.gov (United States)

    Schaltin, Stijn; D'Urzo, Lucia; Zhao, Qiang; Vantomme, André; Plank, Harald; Kothleitner, Gerald; Gspan, Christian; Binnemans, Koen; Fransaer, Jan

    2012-10-21

    In this paper, it is shown that high vacuum conditions are not sufficient to completely remove water and oxygen from the ionic liquid 1-ethyl-3-methylimidazolium chloride. Complete removal of water demands heating above 150 °C under reduced pressure, as proven by Nuclear Reaction Analysis (NRA). Dissolved oxygen gas can only be removed by the use of an oxygen scavenger such as hydroquinone, despite the fact that calculations show that oxygen should be removed completely by the applied vacuum conditions. After applying a strict drying procedure and scavenging of molecular oxygen, it was possible to deposit copper directly on tantalum without the presence of an intervening oxide layer.

  8. LASER Additive Manufacturing of Titanium-Tantalum Alloy Structured Interfaces for Modular Orthopedic Devices

    Science.gov (United States)

    Fuerst, Jacob; Medlin, Dana; Carter, Michael; Sears, James; Vander Voort, George

    2015-04-01

    Tantalum is recognized to have better biocompatibility and osseointegrative properties than other more commonly used orthopedic grade alloys. There are several novel methods that tantalum or tantalum-titanium could be used to augment orthopedic implants. A tantalum or tantalum-titanium alloy at the bone/implant or modular component interfaces would substantially increase the longevity and performance of modular devices. Bonding a functional tantalum coating to a titanium orthopedic device is inherently difficult because of the small difference between the melting temperature of tantalum, 3017°C, and the boiling point of titanium, 3287°C. LASER powder deposition (LPD) is a fusion operation using an Nd:YAG to melt a small volume of substrate into which metal powder is sprayed achieving high temperature with a high solidification rate. LPD of Ti-Ta onto a Ti-6Al-4V substrate produced both a solid surface and structured coating with a pore size in the optimal 350-500 μm range.

  9. Effects of tantalum content on the microstructure and mechanical properties of low-carbon RAFM steel

    Science.gov (United States)

    Chen, Jianguo; Liu, Chenxi; Liu, Yongchang; Yan, Biyu; Li, Huijun

    2016-10-01

    In order to explore the influence of tantalum content on the microstructure and mechanical properties of low carbon RAFM (reduced activation ferritic/martensitic) steels, three low carbon RAFM steels with different tantalum contents (0%, 0.027%, 0.073%) were designed. The precipitation behavior and effect of precipitates on the mechanical properties of the Low-C RAFM steel were investigated. The results indicate that increase of tantalum content causes decrease of the prior austenite grain size and the amount of M23C6 carbides precipitated along prior austenite grain boundaries and packet boundaries as well as increase of the amount of MX nano-sized particles within intragranular regions. The impact properties of low carbon RAFM steels are excellent regardless of the tantalum content. The impact properties and hardness are obviously improved by increasing tantalum content, which may be related to increase of the number of MX and decrease of M23C6. Furthermore, the tensile properties at elevated temperature below 600 °C are hardly changed with increase of tantalum content, yet those at 800 °C are improved with increasing tantalum content. This implies that MX carbides would be more important for tensile properties at higher temperature.

  10. Molybdenum-99 production from reactor irradiation of molybdenum targets: a viable strategy for enhanced availability of technetium-99m.

    Science.gov (United States)

    Pillai, M R A; Knapp, F F Russ

    2012-08-01

    Fission-produced 99Mo (F 99Mo) is traditionally used for fabrication of 99Mo/99mTc alumina-based column generators. In this paper, several emerging strategies are discussed which are being pursued or have been suggested to overcome the continuing shortages of F 99Mo. In addition to the hopeful eventual success of these proposed new 99Mo and 99mTc production technologies, an additional attractive strategy is the alternative production and use of low specific activity (LSA) 99Mo. This strategy avoids fission and is accomplished by direct activation of molybdenum targets in nuclear reactors, which would preclude sole continued reliance on F 99Mo. The principal focus of this paper is a detailed discussion on the advantages and strategies for enhanced production of LSA 99Mo using an international network of research reactors. Several effective strategies are discussed to obtain 99mTc from LSA 99Mo as well as more efficient use of the alumina-based generator system. The delayed time period between 99Mo production and traditional 99Mo/99mTc alumina column generator manufacture and distribution to user sites results in the loss of more than 50% of 99Mo activity. Another strategy is a paradigm shift in the use of 99Mo by recovering clinical-grade 99mTc from 99Mo solution as an alternative to use of 99Mo/99mTc column generators, thereby avoiding substantial decreased availability of 99Mo from radioactive decay. Implementation of the suggested strategies would be expected to increase availability of 99mTc to the clinical user community by several fold. Additional important advantages for the use of LSA 99Mo include eliminating the need for fission product waste management and precluding proliferation concerns by phasing out the need for high (HEU)- and low (LEU)-enriched uranium targets required for F 99Mo production.

  11. Synthesis and characterization of polyvinylpyrrolidine assisted tantalum pentoxide films

    Energy Technology Data Exchange (ETDEWEB)

    Subramanian, Vaidyanathan; Ndiege, Nicholas; Seebauer, E.G. [Department of Chemical and Biomolecular Engineering, University of Illinois at Urbana-Champaignm, 600 S. Mathews, Urbana, IL-61801 (United States); Shannon, Mark A. [Department of Mechanical Engineering, University of Illinois at Urbana-Champaignm, 600 S. Mathews, Urbana, IL-61801 (United States); Masel, Richard I. [Department of Chemical and Biomolecular Engineering, University of Illinois at Urbana-Champaignm, 600 S. Mathews, Urbana, IL-61801 (United States)], E-mail: r-masel@uiuc.edu

    2008-06-02

    Micron thick tantalum pentoxide (Ta{sub 2}O{sub 5}) films have been proposed as thermal insulating layers in microchemical systems, but so far it has been difficult to deposit thick enough films over complex substrates. So far sol-gel films cracked upon heating whenever the film thicknesses were above 350 nm. A 350 nm thick film is too thin for effective insulation. Other techniques are not suitable for coating the complex structures associated with microchemical systems. In this paper we report sol-gel synthesis of 1.6 {mu}m thick tantalum pentoxide (Ta{sub 2}O{sub 5}) films. The films are almost crack free, and adhere to silicon surfaces even upon flashing to 900 deg. C. The key to the synthesis is the addition of Polyvinylpyrrolidine (PVP) to the sol. Films grown in the absence of PVP all show cracks upon calcination to 900 deg. C while few cracks are seen with PVP. X-ray diffraction and Fourier transform infra red analysis show that orthorhombic Ta{sub 2}O{sub 5} is formed in all cases. X-ray photoelectron spectroscopy shows the O:Ta ratio to be 2.8:1. This shows that sol-gel is a viable process for making the micron thick films of Ta{sub 2}O{sub 5} needed as insulators for microchemical systems.

  12. Dinitrogen dissociation on an isolated surface tantalum atom.

    Science.gov (United States)

    Avenier, P; Taoufik, M; Lesage, A; Solans-Monfort, X; Baudouin, A; de Mallmann, A; Veyre, L; Basset, J-M; Eisenstein, O; Emsley, L; Quadrelli, E A

    2007-08-24

    Both industrial and biochemical ammonia syntheses are thought to rely on the cooperation of multiple metals in breaking the strong triple bond of dinitrogen. Such multimetallic cooperation for dinitrogen cleavage is also the general rule for dinitrogen reductive cleavage with molecular systems and surfaces. We have observed cleavage of dinitrogen at 250 degrees C and atmospheric pressure by dihydrogen on isolated silica surface-supported tantalum(III) and tantalum(V) hydride centers [(identical with Si-O)2Ta(III)-H] and [(identical with Si-O)2Ta(V)H3], leading to the Ta(V) amido imido product [(identical with SiO)2Ta(=NH)(NH2)]: We assigned the product structure based on extensive characterization by infrared and solid-state nuclear magnetic resonance spectroscopy, isotopic labeling studies, and supporting data from x-ray absorption and theoretical simulations. Reaction intermediates revealed by in situ monitoring of the reaction with infrared spectroscopy support a mechanism highly distinct from those previously observed in enzymatic, organometallic, and heterogeneous N2 activating systems.

  13. Isolated Subtalar Distraction Arthrodesis Using Porous Tantalum: A Pilot Study.

    Science.gov (United States)

    Papadelis, Eustratios A; Karampinas, Panagiotis K; Kavroudakis, Eustratios; Vlamis, John; Polizois, Vasilios D; Pneumaticos, Spiros G

    2015-09-01

    During reconstructive procedures of the hindfoot, a structural graft is often needed to fill gaps. To eliminate donor site morbidity and limited availability of autografts, porous tantalum was used. Eighteen patients who underwent subtalar joint distraction arthrodesis by means of trabecular metal augment were reviewed retrospectively. The results were evaluated clinically, with the American Orthopaedic Foot & Ankle Society (AOFAS) score and the visual analog scale (VAS) for pain, and were assessed radiologically. The mean follow-up period was 18 months. Computed tomography showed sound fusion. There was a marked increase in AOFAS scores and a decrease in VAS scores. Arthrodesis was achieved in all cases with no major postoperative complications. Radiographically, there was a marked increase in all measured parameters (talocalcaneal angle, talocalcaneal height, talar declination angle), and the intraoperatively achieved correction was maintained at the last follow-up visit. Our data suggest that porous tantalum may be used as a structural graft option for subtalar arthrodesis. Level IV, retrospective case series. © The Author(s) 2015.

  14. Fabrication and characterisation of suspended microstructures of tantalum

    Science.gov (United States)

    Al-masha'al, A.; Mastropaolo, E.; Bunting, A.; Dunare, C.; Cheung, R.

    2017-01-01

    An investigation of the influence of deposition and post-fabrication processes on the final mechanical structure of tantalum beams is reported in the present study. The final deflection profiles of doubly supported beams made from compressive and tensile-stressed films have been studied experimentally. An optimum finite element model has been developed to predict the buckling behaviour of the doubly supported beams by considering the boundary conditions in the form of a compressive stress and an applied load. No matter which etch release method has been used, the initial stress state of the as-deposited films has been found to have a significant impact on the final deflection profile of the fabricated device. The compressive-stressed films have presented larger deflection in the final released beams than the tensile-stressed films. Taking into account the type of etch release methods, the beams that have been released in the dry etch release processes have been found to deform more vertically than those released in the wet-etch release method. Moreover, it has been found that the amplitude of vertical deflection increases with the increase of the beam length and thickness. The results indicate that optimum profiles of tantalum suspended structures can be obtained from the tensile-stressed films that have been released by the wet etching method with an aspect ratio of 1:48.

  15. Synergistic helium and deuterium blistering in tungsten–tantalum composites

    Energy Technology Data Exchange (ETDEWEB)

    Dias, M., E-mail: marta.dias@itn.pt [Associação Euratom/IST, Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Mateus, R.; Catarino, N.; Franco, N. [Associação Euratom/IST, Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Nunes, D. [CENIMAT-I3N, Departamento de Ciência dos Materiais, Faculdade de Ciências e Tecnologia, FCT, Universidade Nova de Lisboa, 2829-516 Caparica (Portugal); Correia, J.B. [LNEG, Laboratório Nacional de Energia e Geologia, Estrada do Paço do Lumiar, 1649-038 Lisboa (Portugal); Carvalho, P.A. [Associação Euratom/IST, Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); ICEMS, Instituto Superior Técnico, Universidade de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Hanada, K. [AIST, National Institute of Advanced Industrial Science and Technology, 1-2-1 Namiki, Tsukuba, 305-8564 Ibaraki (Japan); Sârbu, C. [National Institute of Materials and Physics, 105bis Atomistilor street, 077125 Magurele-Ilfov (Romania); and others

    2013-11-15

    Abstruct: Tungsten–tantalum composites with 10 and 20 at.% Ta were prepared by ball milling W powder with Ta fibers and by consolidating the milled materials with spark plasma sintering. The composites were implanted at room temperature with He{sup +} (30 keV with a fluence 5 × 10{sup 21} at/m{sup 2}) and/or D{sup +} (15 keV with a fluence 5 × 10{sup 21} at/m{sup 2}) ion beams. The materials were studied by scanning and high-resolution transmission electron microscopy, both coupled with energy dispersive X-ray spectroscopy, and by X-ray diffraction, Rutherford backscattering spectrometry and nuclear reaction analysis. The microstructure observations revealed that the milling operation resulted in severe fragmentation of the Ta fibers. Furthermore, during the consolidation process the Ta phase acted as oxygen getter and reduced the W oxide present in the original material. The surface of the tungsten–tantalum composites implanted with D{sup +} remained essentially unaltered, while the materials implanted with He{sup +} evidenced blisters on the Ta-rich regions. D retention in the composites increased with He{sup +} pre-implantation.

  16. Thermotransport of hydrogen and deuterium in vanadium, niobium and tantalum alloys

    Energy Technology Data Exchange (ETDEWEB)

    Smith, M.F.

    1981-10-01

    Heats of transport have been determined for thermotransport of hydrogen and deuterium in pure vanadium, niobium and tantalum; in vanadium alloyed with either niobium, titanium or chromium; and in niobium-tantalum alloys. In all cases, thermotransport was toward colder regions and was significantly greater for deuterium than for hydrogen. A mass spectrometric technique was used to simultaneously measure heats of transport for hydrogen and deuterium in a single specimen containing both isotopes. This technique greatly increased the precision with which isotope effects in the heat of transport could be measured. The predominant effect of alloying was to dramatically increase thermotransport; however, thermotransport decreased as niobium was added to tantalum.

  17. Guidelines for the selection and application of tantalum electrolytic capacitors in highly reliable equipment

    Science.gov (United States)

    Holladay, A. M.

    1978-01-01

    Guidelines are given for the selection and application of three types of tantalum electrolytic capacitors in current use in the design of electrical and electronic circuits for space flight missions. In addition, the guidelines supplement requirements of existing military specifications used in the procurement of capacitors. A need exists for these guidelines to assist designers in preventing some of the recurring, serious problems experienced with tantalum electrolytic capacitors in the recent past. The three types of capacitors covered by these guidelines are; solid, wet foil, and tantalum cased wet slug.

  18. Production Cycle for Large Scale Fission Mo-99 Separation by the Processing of Irradiated LEU Uranium Silicide Fuel Element Targets

    Directory of Open Access Journals (Sweden)

    Abdel-Hadi Ali Sameh

    2013-01-01

    Full Text Available Uranium silicide fuels proved over decades their exceptional qualification for the operation of higher flux material testing reactors with LEU elements. The application of such fuels as target materials, particularly for the large scale fission Mo-99 producers, offers an efficient and economical solution for the related facilities. The realization of such aim demands the introduction of a suitable dissolution process for the applied U3Si2 compound. Excellent results are achieved by the oxidizing dissolution of the fuel meat in hydrofluoric acid at room temperature. The resulting solution is directly behind added to an over stoichiometric amount of potassium hydroxide solution. Uranium and the bulk of fission products are precipitated together with the transuranium compounds. The filtrate contains the molybdenum and the soluble fission product species. It is further treated similar to the in-full scale proven process. The generated off gas stream is handled also as experienced before after passing through KOH washing solution. The generated alkaline fluoride containing waste solution is noncorrosive. Nevertheless fluoride can be selectively bonded as in soluble CaF2 by addition of a mixture of solid calcium hydroxide calcium carbonate to the sand cement mixture used for waste solidification. The generated elevated amounts of LEU remnants can be recycled and retargeted. The related technology permits the minimization of the generated fuel waste, saving environment, and improving processing economy.

  19. Accelerating and guiding of C6 + by an intense laser irradiating on a foil target with a tapered channel

    Science.gov (United States)

    Lv, Chong; Wan, Feng; Hou, Ya-Juan; Hong, Xue-Ren; Jia, Mo-Ran; Sang, Hai-Bo; Xie, Bai-Song

    2017-08-01

    A novel scheme with a tapered channel attached to an ultra-thin carbon foil is proposed to accelerate and guide carbon ions via breakout afterburner mechanism. Also, the problems involved are investigated by using two-dimensional particle-in-cell simulations. It is demonstrated that the tapered channel can efficiently accelerate and guide carbon ions and result in a much better quality beam with an order of magnitude higher in density and 22% larger in cut-off energy than that without the tapered channel. The enhanced reasons are analyzed in detail, which are mainly attributed to the guidance of the longitudinal electric field and the focus of the transverse electric field, as well as the convergence effect of the tapered channel. All of them are certified to guide greatly carbon ions to move along the longitudinal direction. Besides, during the simulation time, the ion beam with a tapered channel can remain eight times smaller in divergence angle than that without the tapered channel. Such a target may be beneficial to many applications such as ion fast ignition in inertial fusion, high-energy physics, and proton therapy.

  20. In situ observation of the reaction of tantalum with nitrogen in a laser heated diamond anvil cell

    Energy Technology Data Exchange (ETDEWEB)

    Friedrich, Alexandra, E-mail: friedrich@kristall.uni-frankfurt.d [Institut fuer Geowissenschaften, Goethe-Universitaet Frankfurt, Altenhoeferallee 1, D-60438 Frankfurt am Main (Germany); Winkler, Bjoern; Bayarjargal, Lkhamsuren [Institut fuer Geowissenschaften, Goethe-Universitaet Frankfurt, Altenhoeferallee 1, D-60438 Frankfurt am Main (Germany); Juarez Arellano, Erick A. [Universidad del Papaloapan, Circuito Central 200, Parque Industrial, Tuxtepec 68301 (Mexico); Morgenroth, Wolfgang; Biehler, Jasmin; Schroeder, Florian [Institut fuer Geowissenschaften, Goethe-Universitaet Frankfurt, Altenhoeferallee 1, D-60438 Frankfurt am Main (Germany); Yan, Jinyuan; Clark, Simon M. [Advanced Light Source, Lawrence Berkeley National Laboratory, MS6R2100, 1 Cyclotron Road, Berkeley, CA 94720-8226 (United States)

    2010-07-16

    Tantalum nitrides were formed by reaction of the elements at pressures between 9(1) and 12.7(5) GPa and temperatures >1600-2000 K in the laser-heated diamond anvil cell. The incorporation of small amount of nitrogen in the tantalum structure was identified as the first reaction product on weak laser irradiation. Subsequent laser heating led to the formation of hexagonal {beta}-Ta{sub 2}N and orthorhombic {eta}-Ta{sub 2}N{sub 3}, which was the stable phase at pressures up to 27 GPa and high temperatures. No evidence was found for the presence of {epsilon}-TaN, {theta}-TaN, {delta}-TaN, Ta{sub 3}N{sub 5}-I or Ta{sub 3}N{sub 5}-II, which was predicted to be the stable phase at P>17 GPa and T=2800 K, at the P,T-conditions of this experiment. The bulk modulus of {eta}-Ta{sub 2}N{sub 3} was determined to be B{sub 0}=319(6) GPa from a 2nd order Birch-Murnaghan equation of state fit to the experimental data, while quantum mechanical calculations using the density functional theory gave a bulk modulus of B{sub 0}=348.0(9) GPa for a 2nd-order fit or B{sub 0}=339(1) GPa and B{sup '}=4.67(9) for a 3rd-order fit. The values show the large incompressibility of this high-pressure phase. From the DFT data the structural compression mechanism could be determined.

  1. Development of distributed target

    CERN Document Server

    Yu Hai Jun; Li Qin; Zhou Fu Xin; Shi Jin Shui; Ma Bing; Chen Nan; Jing Xiao Bing

    2002-01-01

    Linear introduction accelerator is expected to generate small diameter X-ray spots with high intensity. The interaction of the electron beam with plasmas generated at the X-ray converter will make the spot on target increase with time and debase the X-ray dose and the imaging resolving power. A distributed target is developed which has about 24 pieces of thin 0.05 mm tantalum films distributed over 1 cm. due to the structure adoption, the distributed target material over a large volume decreases the energy deposition per unit volume and hence reduces the temperature of target surface, then reduces the initial plasma formalizing and its expansion velocity. The comparison and analysis with two kinds of target structures are presented using numerical calculation and experiments, the results show the X-ray dose and normalized angle distribution of the two is basically the same, while the surface of the distributed target is not destroyed like the previous block target

  2. Pulsed irradiation improves target selectivity of infrared laser-evoked gene operator for single-cell gene induction in the nematode C. elegans.

    Directory of Open Access Journals (Sweden)

    Motoshi Suzuki

    Full Text Available Methods for turning on/off gene expression at the experimenter's discretion would be useful for various biological studies. Recently, we reported on a novel microscope system utilizing an infrared laser-evoked gene operator (IR-LEGO designed for inducing heat shock response efficiently in targeted single cells in living organisms without cell damage, thereby driving expression of a transgene under the control of a heat shock promoter. Although the original IR-LEGO can be successfully used for gene induction, several limitations hinder its wider application. Here, using the nematode Caenorhabditis elegans (C. elegans as a subject, we have made improvements in IR-LEGO. For better spatial control of heating, a pulsed irradiation method using an optical chopper was introduced. As a result, single cells of C. elegans embryos as early as the 2-cell stage and single neurons in ganglia can be induced to express genes selectively. In addition, the introduction of site-specific recombination systems to IR-LEGO enables the induction of gene expression controlled by constitutive and cell type-specific promoters. The strategies adopted here will be useful for future applications of IR-LEGO to other organisms.

  3. Development of high temperature targets at IRIS facility

    CERN Document Server

    Panteleev, V N; Fedorov, D V; Moroz, F V; Orlov, S Y; Poljakov, A G; Seliverstov, D M; Volkov, Y M

    2002-01-01

    High-temperature targets with different kind of target material, as tantalum foils, tungsten foils, NbC powder, TaC powder and UC powder have been developed and off-line and on-line tested. The yield and delay time measurements have been carried out for radioactive isotopes of Li, Rb and Cs.

  4. A STUDY OF THE GALLIC ACID COMPLEXES OF NIOBIUM, TANTALUM, TITANIUM, AND IRON,

    Science.gov (United States)

    The use of gallic acid in a spectrophotometric procecure for tantalum, niobium and other metals was investigated. The optical properties of Nb, Ta and several other metal chelates were explored. (Author)

  5. High-quality-factor tantalum oxide nanomechanical resonators by laser oxidation of TaSe2

    Institute of Scientific and Technical Information of China (English)

    Santiago J. CartamiI-Bueno[1; Peter G. Steeneken[1; Frans D. Tichelaar[2; Efren Navarro-Moratalla[3; Warner J. Venstra[1; Ronald van Leeuwen[1; Eugenio Coronado[3; Herre S.J. van der Zant[1; Gary A. Steele[1; Andres Castellanos-Gomez[1

    2015-01-01

    Controlling the strain in two-dimensional (2D) materials is an interesting avenue to tailor the mechanical properties of nanoelectromechanical systems. Here, we demonstrate a technique to fabricate ultrathin tantalum oxide nanomechanical resonators with large stress by the laser oxidation of nano-drumhead resonators composed of tantalum diselenide (TaSe2), a layered 2D material belonging to the metal dichalcogenides. Before the study of their mechanical properties with a laser interferometer, we verified the oxidation and crystallinity of the freely suspended tantalum oxide using high-resolution electron microscopy. We demonstrate that the stress of tantalum oxide resonators increases by 140 MPa (with respect to pristine TaSe2 resonators), which causes an enhancement in the quality factor (14 times larger) and resonance frequency (9 times larger) of these resonators.

  6. Effect of Heat Treatment on Mechanical Properties and Corrosion Performance of Cold-Sprayed Tantalum Coatings

    Science.gov (United States)

    Kumar, S.; Vidyasagar, V.; Jyothirmayi, A.; Joshi, S. V.

    2016-04-01

    The cold-spray technique is of significant interest to deposit refractory metals with relatively high melting point for a variety of demanding applications. In the present study, mechanical properties of cold-sprayed tantalum coatings heat treated at different temperatures were investigated using microtensile testing, scratch testing, and nanoindentation. The corrosion performance of heat-treated coatings was also evaluated in 1 M KOH solution, and potentiodynamic polarization as well as impedance spectroscopy studies were carried out. Assessment of structure-property correlations was attempted based on microstructure, porosity, and intersplat bonding state, together with mechanical and corrosion properties of the heat-treated cold-sprayed tantalum coatings. Coatings annealed at 1500 °C, which is very close to the recrystallization temperature of tantalum, were found to perform almost as bulk tantalum, with exciting implications for various applications.

  7. Vacuum pyrolysis characteristics and parameter optimization of recycling organic materials from waste tantalum capacitors.

    Science.gov (United States)

    Chen, Zhenyang; Niu, Bo; Zhang, Lingen; Xu, Zhenming

    2017-08-12

    Recycling rare metal tantalum from waste tantalum capacitors (WTCs) is significant to alleviate the shortage of tantalum resource. However, environmental problems will be caused if the organic materials from WTCs are improperly disposed. This study presented a promising vacuum pyrolysis technology to recycle the organic materials from WTCs. The organics removal rate could reach 94.32wt% according to TG results. The optimal parameters were determined as 425°C, 50Pa and 30min on the basis of response surface methodology (RSM). The oil yield and residual rate was 18.09wt% and 74.94wt%, respectively. All pyrolysis products can be recycled through a reasonable route. Besides, to deeply understand the pyrolysis process, the pyrolysis mechanism was also proposed based on the product and free radical theory. This paper provides an efficient process for recycling the organic material from WTCs, which can facilitate the following tantalum recovery. Copyright © 2017 Elsevier B.V. All rights reserved.

  8. World War II, tantalum, and the evolution of modern cranioplasty technique.

    Science.gov (United States)

    Flanigan, Patrick; Kshettry, Varun R; Benzel, Edward C

    2014-04-01

    Cranioplasty is a unique procedure with a rich history. Since ancient times, a diverse array of materials from coconut shells to gold plates has been used for the repair of cranial defects. More recently, World War II greatly increased the demand for cranioplasty procedures and renewed interest in the search for a suitable synthetic material for cranioprostheses. Experimental evidence revealed that tantalum was biologically inert to acid and oxidative stresses. In fact, the observation that tantalum did not absorb acid resulted in the metal being named after Tantalus, the Greek mythological figure who was condemned to a pool of water in the Underworld that would recede when he tried to take a drink. In clinical use, malleability facilitated a single-stage cosmetic repair of cranial defects. Tantalum became the preferred cranioplasty material for more than 1000 procedures performed during World War II. In fact, its use was rapidly adopted in the civilian population. During World War II and the heyday of tantalum cranioplasty, there was a rapid evolution in prosthesis implantation and fixation techniques significantly shaping how cranioplasties are performed today. Several years after the war, acrylic emerged as the cranioplasty material of choice. It had several clear advantages over its metallic counterparts. Titanium, which was less radiopaque and had a more optimal thermal conductivity profile (less thermally conductive), eventually supplanted tantalum as the most common metallic cranioplasty material. While tantalum cranioplasty was popular for only a decade, it represented a significant breakthrough in synthetic cranioplasty. The experiences of wartime neurosurgeons with tantalum cranioplasty played a pivotal role in the evolution of modern cranioplasty techniques and ultimately led to a heightened understanding of the necessary attributes of an ideal synthetic cranioplasty material. Indeed, the history of tantalum cranioplasty serves as a model for innovative

  9. Thermal Conductivity of Saturated Liquid Toluene by Use of Anodized Tantalum Hot Wires at High Temperatures

    OpenAIRE

    Perkins, R. A.; Ramires, M. L. V.; Nieto de Castro, C. A.

    2000-01-01

    Absolute measurements of the thermal conductivity of a distilled and dried sample of toluene near saturation are reported. The transient hot-wire technique with an anodized tantalum hot wire was used. The thermal conductivities were measured at temperatures from 300 K to 550 K at different applied power levels to assess the uncertainty with which it is possible to measure liquid thermal conductivity over wide temperature ranges with an anodized tantalum wire. The wire resistance versus temper...

  10. Tunable structural color of anodic tantalum oxide films

    Institute of Scientific and Technical Information of China (English)

    Sheng Cui-Cui; Cai Yun-Yu; Dai En-Mei; Liang Chang-Hao

    2012-01-01

    Tantalum (Ta) oxide films with tunable structural color were fabricated easily using anodic oxidation.The structure,components,and surface valence states of the oxide filns were investigated by using gazing incidence X-ray diffractometry,X-ray photoelectron microscopy,and surface analytical techniques.Their thickness and optical properties were studied by using spectroscopic ellipsometry and total reflectance spectrum.Color was accurately defined using L*a*b* scale.The thickness of compact Ta2O5 films was linearly dependent on anodizing voltage.The film color was tunable by adjusting the anodic voltage.The difference in color appearance resulted from the interference behavior between the interfaces of air-oxide and oxide-metal.

  11. Subtrochanteric Fracture following Removal of a Porous Tantalum Implant

    Directory of Open Access Journals (Sweden)

    Derek F. Amanatullah

    2013-01-01

    Full Text Available Osteonecrosis of the hip accounts for about 10% of all total hip arthroplasty cases and presents a significant challenge for those patients with and without femoral head collapse. Subtrochanteric femur fractures have been reported with numerous types of proximal femoral implants. Care must be taken to avoid penetrating the lateral cortex of the proximal femur inferior to the distal border of the lesser trochanter. Core decompression requires a 3 mm to 20 mm defect in the lateral femoral cortex. Subtrochanteric femur fractures are a well-known complication of core decompression as well. We present a case of a subtrochanteric fracture following the removal of a porous tantalum implant.

  12. Effect of dilute tungsten alloying on the dynamic strength of tantalum under ramp compression

    Science.gov (United States)

    Alexander, C. S.; Brown, J. L.; Millett, J. C. F.; Whiteman, G.; Asay, J. R.; Bourne, N. K.

    2015-06-01

    The strength of tantalum and tantalum alloys are of considerable interest due to their widespread use in both military and industrial applications. Previous work has shown that strength in these materials is tied to dislocation density and mobility within the microstructure. Accordingly, strength has been observed to increase with dilute alloying which serves to increase the dislocation density. In this study, we examine the effect of alloying on the strength of a dilute tantalum-tungsten alloy (2.5 weight percent W) under ramp compression. The strength of the alloy is measured using the ``self-consistent'' technique which examines the response under longitudinal unloading from peak compression. The results are compared to previous studies of pure tantalum and dilute tantalum-tungsten alloys under both shock and ramp compression and indicate strengthening of the alloy when compared to pure tantalum. Sandia National Labs is a multi-program laboratory managed and operated by Sandia Corp., a wholly owned subsidiary of Lockheed Martin Corp., for the U.S. Department of Energy's National Nuclear Security Administration under Contract DE-AC04-94AL85000.

  13. Can porous tantalum be used to achieve ankle and subtalar arthrodesis?: a pilot study.

    Science.gov (United States)

    Frigg, Arno; Dougall, Hugh; Boyd, Steve; Nigg, Benno

    2010-01-01

    A structural graft often is needed to fill gaps during reconstructive procedures of the ankle and hindfoot. Autograft, the current gold standard, is limited in availability and configuration and is associated with donor-site morbidity in as much as 48%, whereas the alternative allograft carries risks of disease transmission and collapse. Trabecular metal (tantalum), with a healing rate similar to that of autograft, high stability, and no donor-site morbidity, has been used in surgery of the hip, knee, and spine. However, its use has not been documented in foot and ankle surgery. We retrospectively reviewed nine patients with complex foot and ankle arthrodeses using a tantalum spacer. Minimum followup was 1.9 years (average, 2 years; range, 1.9-2.4 years). Bone ingrowth into the tantalum was analyzed with micro-CT in three of the nine patients. All arthrodeses were fused clinically and radiographically at the 1- and 2 year followups and no complications occurred. The American Orthopaedic Foot and Ankle Society score increased from 32 to 74. The micro-CT showed bony trabeculae growing onto the tantalum. Our data suggest tantalum may be used as a structural graft option for ankle and subtalar arthrodesis. All nine of our patients achieved fusion and had no complications. Using tantalum obviated the need for harvesting of the iliac spine. Level IV, therapeutic study. See Guidelines for Authors for a complete description of levels of evidence.

  14. Dosimetric impact of tantalum markers used in the treatment of uveal melanoma with proton beam therapy

    Energy Technology Data Exchange (ETDEWEB)

    Newhauser, Wayne D [University of Texas M D Anderson Cancer Center, 1515 Holcombe Boulevard, Unit 94, Houston, TX 77030 (United States); Koch, Nicholas C [University of Texas M D Anderson Cancer Center, 1515 Holcombe Boulevard, Unit 94, Houston, TX 77030 (United States); Fontenot, Jonas D [University of Texas M D Anderson Cancer Center, 1515 Holcombe Boulevard, Unit 94, Houston, TX 77030 (United States); Rosenthal, Stanley J [Massachusetts General Hospital, 55 Fruit Street, Boston, MA 02114 (United States); Gombos, Dan S [Section of Opthalmology, Department of Head and Neck Surgery, University of Texas M D Anderson Cancer Center, 1515 Holcombe Boulevard, Unit 94, Houston, TX 77030 (United States); Fitzek, Markus M [Midwest Proton Radiotherapy Institute, 2425 Milo B Sampson Lane, Bloomington, IN 47408 (United States); Mohan, Radhe [University of Texas M D Anderson Cancer Center, 1515 Holcombe Boulevard, Unit 94, Houston, TX 77030 (United States)

    2007-07-07

    Metallic fiducial markers are frequently implanted in patients prior to external-beam radiation therapy to facilitate tumor localization. There is little information in the literature, however, about the perturbations in proton absorbed-dose distribution these objects cause. The aim of this study was to assess the dosimetric impact of perturbations caused by 2.5 mm diameter by 0.2 mm thick tantalum fiducial markers when used in proton therapy for treating uveal melanoma. Absorbed dose perturbations were measured using radiochromic film and confirmed by Monte Carlo simulations of the experiment. Additional Monte Carlo simulations were performed to study the effects of range modulation and fiducial placement location on the magnitude of the dose shadow for a representative uveal melanoma treatment. The simulations revealed that the fiducials caused perturbations in the absorbed-dose distribution, including absorbed-dose shadows of 22% to 82% in a typical proton beam for treating uveal melanoma, depending on the marker depth and orientation. The clinical implication of this study is that implanted fiducials may, in certain circumstances, cause dose shadows that could lower the tumor dose and theoretically compromise local tumor control. To avoid this situation, fiducials should be positioned laterally or distally with respect to the target volume.

  15. In-situ small-angle x-ray scattering study of nanoparticles in the plasma plume induced by pulsed laser irradiation of metallic targets

    Energy Technology Data Exchange (ETDEWEB)

    Lavisse, L.; Jouvard, J.-M.; Girault, M.; Potin, V.; Andrzejewski, H.; Marco de Lucas, M. C.; Bourgeois, S. [Laboratoire Interdisciplinaire Carnot de Bourgogne (ICB), UMR 6303 CNRS-Universite de Bourgogne, 9 Avenue A. Savary, BP 47870-21078 Dijon Cedex (France); Le Garrec, J.-L.; Carles, S.; Mitchell, J. B. A. [Institut de Physique de Rennes, UMR 6251 CNRS-Universite de Rennes 1, 35042 Rennes Cedex (France); Hallo, L. [CEA CESTA, 15 Avenue des Sablieres CS 60001, 33116 Le Barp Cedex (France); Perez, J. [Synchrotron SOLEIL, L' Orme des Merisiers, Saint-Aubin, F-91192 Gif-sur-Yvette Cedex (France); Decloux, J. [Kaluti System, Optique et Laser, Centre Scientifique d' Orsay, 91400 Orsay (France)

    2012-04-16

    Small angle x-ray scattering was used to probe in-situ the formation of nanoparticles in the plasma plume generated by pulsed laser irradiation of a titanium metal surface under atmospheric conditions. The size and morphology of the nanoparticles were characterized as function of laser irradiance. Two families of nanoparticles were identified with sizes on the order of 10 and 70 nm, respectively. These results were confirmed by ex-situ transmission electron microscopy experiments.

  16. Non-oxidative coupling reaction of methane to ethane and hydrogen catalyzed by the silica-supported tantalum hydride: ([triple bond]SiO)2Ta-H.

    Science.gov (United States)

    Soulivong, Daravong; Norsic, Sébastien; Taoufik, Mostafa; Copéret, Christophe; Thivolle-Cazat, Jean; Chakka, Sudhakar; Basset, Jean-Marie

    2008-04-16

    Silica-supported tantalum hydride, (SiO)2Ta-H (1), proves to be the first single-site catalyst for the direct non-oxidative coupling transformation of methane into ethane and hydrogen at moderate temperatures, with a high selectivity (>98%). The reaction likely involves the tantalum-methyl-methylidene species as a key intermediate, where the methyl ligand can migrate onto the tantalum-methylidene affording the tantalum-ethyl.

  17. Addition of oxygen to and distribution of oxides in tantalum alloy T-111 at low concentrations

    Science.gov (United States)

    Stecura, S.

    1975-01-01

    Oxygen was added at 820 and 990 C at an oxygen pressure of about .0003 torr. The technique permitted predetermined and reproducible oxygen doping of the tantalum alloy (T-111). Based on the temperature dependency of the doping reaction, it was concluded that the initial rates of oxygen pickup are probably controlled by solution of oxygen into the T-111 lattice. Although hafnium oxides are more stable than those of tantalum or tungsten, analyses of extracted residues indicate that the tantalum and tungsten oxides predominate in the as-doped specimens, presumably because of the higher concentrations of tantalum and tungsten in the alloy. However, high-temperature annealing promotes gettering of dissolved oxygen and oxygen from other oxides to form hafnium oxides. Small amounts of tantalum and tungsten oxides were still present after high temperature annealing. Tungsten oxide (WO3) volatilizes slightly from the surface of T-111 at 990 C but not at 820 C. The vaporization of WO3 has no apparent effect on the doping reaction.

  18. Synthesis of Coral-Like Tantalum Oxide Films via Anodization in Mixed Organic-Inorganic Electrolytes

    Science.gov (United States)

    Yu, Hongbin; Zhu, Suiyi; Yang, Xia; Wang, Xinhong; Sun, Hongwei; Huo, Mingxin

    2013-01-01

    We report a simple method to fabricate nano-porous tantalum oxide films via anodization with Ta foils as the anode at room temperature. A mixture of ethylene glycol, phosphoric acid, NH4F and H2O was used as the electrolyte where the nano-porous tantalum oxide could be synthesized by anodizing a tantalum foil for 1 h at 20 V in a two–electrode configuration. The as-prepared porous film exhibited a continuous, uniform and coral-like morphology. The diameters of pores ranged from 30 nm to 50 nm. The pores interlaced each other and the depth was about 150 nm. After calcination, the as-synthesized amorphous tantalum oxide could be crystallized to the orthorhombic crystal system. As observed in photocatalytic experiments, the coral-like tantalum oxide exhibited a higher photocatalytic activity for the degradation of phenol than that with a compact surface morphology, and the elimination rate of phenol increased by 66.7%. PMID:23799106

  19. Synthesis of coral-like tantalum oxide films via anodization in mixed organic-inorganic electrolytes.

    Directory of Open Access Journals (Sweden)

    Hongbin Yu

    Full Text Available We report a simple method to fabricate nano-porous tantalum oxide films via anodization with Ta foils as the anode at room temperature. A mixture of ethylene glycol, phosphoric acid, NH4F and H2O was used as the electrolyte where the nano-porous tantalum oxide could be synthesized by anodizing a tantalum foil for 1 h at 20 V in a two-electrode configuration. The as-prepared porous film exhibited a continuous, uniform and coral-like morphology. The diameters of pores ranged from 30 nm to 50 nm. The pores interlaced each other and the depth was about 150 nm. After calcination, the as-synthesized amorphous tantalum oxide could be crystallized to the orthorhombic crystal system. As observed in photocatalytic experiments, the coral-like tantalum oxide exhibited a higher photocatalytic activity for the degradation of phenol than that with a compact surface morphology, and the elimination rate of phenol increased by 66.7%.

  20. Porous tantalum coatings prepared by vacuum plasma spraying enhance bmscs osteogenic differentiation and bone regeneration in vitro and in vivo.

    Directory of Open Access Journals (Sweden)

    Ze Tang

    Full Text Available Tantalum, as a potential metallic implant biomaterial, is attracting more and more attention because of its excellent anticorrosion and biocompatibility. However, its significantly high elastic modulus and large mechanical incompatibility with bone tissue make it unsuitable for load-bearing implants. In this study, porous tantalum coatings were first successfully fabricated on titanium substrates by vacuum plasma spraying (VPS, which would exert the excellent biocompatibility of tantalum and alleviate the elastic modulus of tantalum for bone tissue. We evaluated cytocompatibility and osteogenesis activity of the porous tantalum coatings using human bone marrow stromal cells (hBMSCs and its ability to repair rabbit femur bone defects. The morphology and actin cytoskeletons of hBMSCs were observed via electron microscopy and confocal, and the cell viability, proliferation and osteogenic differentiation potential of hBMSCs were examined quantitatively by PrestoBlue assay, Ki67 immunofluorescence assay, real-time PCR technology and ALP staining. For in vivo detection, the repaired femur were evaluated by histomorphology and double fluorescence labeling 3 months postoperation. Porous tantalum coating surfaces promoted hBMSCs adhesion, proliferation, osteogenesis activity and had better osseointegration and faster new bone formation rate than titanium coating control. Our observation suggested that the porous tantalum coatings had good biocompatibility and could enhance osseoinductivity in vitro and promote new bone formation in vivo. The porous tantalum coatings prepared by VPS is a promising strategy for bone regeneration.

  1. Effect of aluminum on hydrogen absorption kinetics of tantalum

    Energy Technology Data Exchange (ETDEWEB)

    Taxak, Manju, E-mail: m.taxak@gmail.com; Krishnamurthy, Nagaiyar

    2015-02-25

    Highlights: • The hydrogen absorption kinetics in Ta–Al alloys is investigated for the first time. • The rate constant for hydrogen absorption increases with increasing temperature. • The three-dimensional diffusion is the rate-limiting step of hydrogen absorption in Ta–Al alloys. • The apparent activation energy for hydrogen absorption in Ta–Al alloys increases with increasing Al content. - Abstract: The isothermal hydrogen absorption kinetics of Ta{sub 1−z}Al{sub z} alloys (z = 0, 1, 1.6 and 2.4 atom%) has been investigated in the temperature range of 673–973 K. The reacted fractions of hydrogen as well as reaction rate constant have been determined from time dependent hydrogen absorption curves using pressure drop method. The variation in rate constant with respect to temperature has been observed for all the alloys. Three-dimensional diffusion processes seems to be the intrinsic rate limiting step of hydrogen absorption. The apparent activation energy of hydrogen absorption has been calculated using Arrhenius equation. With increasing aluminum concentration, the hydrogen absorption kinetics slows down. Consequently, the rate constant decreases and the apparent activation energy of hydrogen absorption increases. The apparent activation energy of hydrogen absorption increases from 53.7 to 57.7 kJ/mol with increasing Al concentration from 0 to 2.4 atom% in tantalum.

  2. Multistate Memristive Tantalum Oxide Devices for Ternary Arithmetic

    Science.gov (United States)

    Kim, Wonjoo; Chattopadhyay, Anupam; Siemon, Anne; Linn, Eike; Waser, Rainer; Rana, Vikas

    2016-01-01

    Redox-based resistive switching random access memory (ReRAM) offers excellent properties to implement future non-volatile memory arrays. Recently, the capability of two-state ReRAMs to implement Boolean logic functionality gained wide interest. Here, we report on seven-states Tantalum Oxide Devices, which enable the realization of an intrinsic modular arithmetic using a ternary number system. Modular arithmetic, a fundamental system for operating on numbers within the limit of a modulus, is known to mathematicians since the days of Euclid and finds applications in diverse areas ranging from e-commerce to musical notations. We demonstrate that multistate devices not only reduce the storage area consumption drastically, but also enable novel in-memory operations, such as computing using high-radix number systems, which could not be implemented using two-state devices. The use of high radix number system reduces the computational complexity by reducing the number of needed digits. Thus the number of calculation operations in an addition and the number of logic devices can be reduced. PMID:27834352

  3. Structure and phase composition of deposited tantalum-carbon films

    Science.gov (United States)

    Tuleushev, Yu. Zh.; Volodin, V. N.; Zhakanbaev, E. A.; Alimzhan, B.

    2016-08-01

    Ion plasma sputtering and the subsequent codeposition of ultrafine tantalum and carbon particles were used to prepare coatings with 4.6-71.5 at % C. Structural studies of the coatings showed the existence of carbon solid solutions in β Ta at carbon contents to 4.6 at %, carbon solid solutions in α Ta at carbon contents of 4.6-10.3 at %, and direct synthesis of TaC at carbon contents of 44.7-71.5 at %. During heat treatments to 700°C, the substantial concentration widening of regions of the existence of Ta2C and TaC was found. The lattice parameters of hexagonal Ta2C and fcc TaC carbides were determined for composition ranges of the existence of phases during heating to 700°C. Upon heating above 600°C, the progressive transition of quasiamorphous Ta2C carbide into the crystalline Ta2C carbide was found to take place. The possibility of applying the direct synthesis of TaC carbide in engineering was noted.

  4. Multistate Memristive Tantalum Oxide Devices for Ternary Arithmetic

    Science.gov (United States)

    Kim, Wonjoo; Chattopadhyay, Anupam; Siemon, Anne; Linn, Eike; Waser, Rainer; Rana, Vikas

    2016-11-01

    Redox-based resistive switching random access memory (ReRAM) offers excellent properties to implement future non-volatile memory arrays. Recently, the capability of two-state ReRAMs to implement Boolean logic functionality gained wide interest. Here, we report on seven-states Tantalum Oxide Devices, which enable the realization of an intrinsic modular arithmetic using a ternary number system. Modular arithmetic, a fundamental system for operating on numbers within the limit of a modulus, is known to mathematicians since the days of Euclid and finds applications in diverse areas ranging from e-commerce to musical notations. We demonstrate that multistate devices not only reduce the storage area consumption drastically, but also enable novel in-memory operations, such as computing using high-radix number systems, which could not be implemented using two-state devices. The use of high radix number system reduces the computational complexity by reducing the number of needed digits. Thus the number of calculation operations in an addition and the number of logic devices can be reduced.

  5. Phase Transformation in Tantalum under Extreme Laser Deformation

    Science.gov (United States)

    Lu, C.-H.; Hahn, E. N.; Remington, B. A.; Maddox, B. R.; Bringa, E. M.; Meyers, M. A.

    2015-10-01

    The structural and mechanical response of metals is intimately connected to phase transformations. For instance, the product of a phase transformation (martensite) is responsible for the extraordinary range of strength and toughness of steel, making it a versatile and important structural material. Although abundant in metals and alloys, the discovery of new phase transformations is not currently a common event and often requires a mix of experimentation, predictive computations, and luck. High-energy pulsed lasers enable the exploration of extreme pressures and temperatures, where such discoveries may lie. The formation of a hexagonal (omega) phase was observed in recovered monocrystalline body-centered cubic tantalum of four crystallographic orientations subjected to an extreme regime of pressure, temperature, and strain-rate. This was accomplished using high-energy pulsed lasers. The omega phase and twinning were identified by transmission electron microscopy at 70 GPa (determined by a corresponding VISAR experiment). It is proposed that the shear stresses generated by the uniaxial strain state of shock compression play an essential role in the transformation. Molecular dynamics simulations show the transformation of small nodules from body-centered cubic to a hexagonal close-packed structure under the same stress state (pressure and shear).

  6. Activation Energy of Tantalum-Tungsten Oxide Thermite Reaction

    Energy Technology Data Exchange (ETDEWEB)

    Cervantes, O; Kuntz, J; Gash, A; Munir, Z

    2010-02-25

    The activation energy of a high melting temperature sol-gel (SG) derived tantalum-tungsten oxide thermite composite was determined using the Kissinger isoconversion method. The SG derived powder was consolidated using the High Pressure Spark Plasma Sintering (HPSPS) technique to 300 and 400 C to produce pellets with dimensions of 5 mm diameter by 1.5 mm height. A custom built ignition setup was developed to measure ignition temperatures at high heating rates (500-2000 C {center_dot} min{sup -1}). Such heating rates were required in order to ignite the thermite composite. Unlike the 400 C samples, results show that the samples consolidated to 300 C undergo an abrupt change in temperature response prior to ignition. This change in temperature response has been attributed to the crystallization of the amorphous WO{sub 3} in the SG derived Ta-WO{sub 3} thermite composite and not to a pre-ignition reaction between the constituents. Ignition temperatures for the Ta-WO{sub 3} thermite ranged from approximately 465-670 C. The activation energy of the SG derived Ta-WO{sup 3} thermite composite consolidated to 300 and 400 C were determined to be 37.787 {+-} 1.58 kJ {center_dot} mol{sup -1} and 57.381 {+-} 2.26 kJ {center_dot} mol{sup -1}, respectively.

  7. Investigation of Tantalum Recycling by Electron Beam Melting

    Directory of Open Access Journals (Sweden)

    Katia Vutova

    2016-11-01

    Full Text Available Investigations are carried out and obtained experimental and theoretical data for tantalum scrap recycling by electron beam melting (EBM is presented in this paper. Different thermal treatment process conditions are realized and results are discussed. A chemical analysis is performed and refining mechanisms for electron beam (EB refining of Ta are discussed. For the performed experiments the best purification of Ta (99.96 is obtained at 21.6 kW beam power for a melting time of 3 min. A statistical approach is applied for estimation of the material losses and the liquid pool characteristics based on experimentally-obtained data. The aim is to improve the EBM and choosing optimal process conditions, depending on the concrete characteristic requirements. Model-based quality optimization of electron beam melting and refining (EBMR processes of Ta is considered related to the optimization of the molten pool parameters, connected to the occurring refining processes, and to minimal material losses. Optimization of the process of EBM of Ta is based on overall criteria, giving compromised solutions, depending on the requirements concerning the quality of the performed products. The accumulated data, the obtained results, and the optimization statistical approach allow us to formulate requirements on the process parameters.

  8. Phase Transformation in Tantalum under Extreme Laser Deformation.

    Science.gov (United States)

    Lu, C-H; Hahn, E N; Remington, B A; Maddox, B R; Bringa, E M; Meyers, M A

    2015-10-19

    The structural and mechanical response of metals is intimately connected to phase transformations. For instance, the product of a phase transformation (martensite) is responsible for the extraordinary range of strength and toughness of steel, making it a versatile and important structural material. Although abundant in metals and alloys, the discovery of new phase transformations is not currently a common event and often requires a mix of experimentation, predictive computations, and luck. High-energy pulsed lasers enable the exploration of extreme pressures and temperatures, where such discoveries may lie. The formation of a hexagonal (omega) phase was observed in recovered monocrystalline body-centered cubic tantalum of four crystallographic orientations subjected to an extreme regime of pressure, temperature, and strain-rate. This was accomplished using high-energy pulsed lasers. The omega phase and twinning were identified by transmission electron microscopy at 70 GPa (determined by a corresponding VISAR experiment). It is proposed that the shear stresses generated by the uniaxial strain state of shock compression play an essential role in the transformation. Molecular dynamics simulations show the transformation of small nodules from body-centered cubic to a hexagonal close-packed structure under the same stress state (pressure and shear).

  9. Strontium adsorption on tantalum-doped hexagonal tungsten oxide.

    Science.gov (United States)

    Li, Xingliang; Mu, Wanjun; Xie, Xiang; Liu, Bijun; Tang, Hui; Zhou, Guanhong; Wei, Hongyuan; Jian, Yuan; Luo, Shunzhong

    2014-01-15

    Hexagonal tungsten oxide (hex-WO3) has the potential to separate (137)Cs and (90)Sr from nuclear power plant or fission (99)Mo production waste. This study aims to increase the capacity of hex-WO3 to adsorb Sr(2+). Ta-doped hex-WO3 was synthesized by the hydrothermal treatment of sodium tungstate dihydrate and tantalum chloride in concentrated HCl, in the presence of ammonium sulfate. Incorporating Ta into the WO3 framework caused the interlayer spacing to expand, and the band gap to shift to higher energy. The Sr(2+) adsorption capacity of Ta-doped hex-WO3 was significantly higher than that of hex-WO3. Sr(2+) adsorption reached equilibrium within 2h in acidic solution. Maximum Sr(2+) removal occurred at pH 4. Sr(2+) uptake by hex-WO3 was described better by the Freundlich model than by the Langmuir model. Sr(2+) adsorption on hex-WO3 was spontaneous under the studied conditions.

  10. Reliability of High-Voltage Tantalum Capacitors. Parts 3 and 4)

    Science.gov (United States)

    Teverovsky, Alexander

    2010-01-01

    Weibull grading test is a powerful technique that allows selection and reliability rating of solid tantalum capacitors for military and space applications. However, inaccuracies in the existing method and non-adequate acceleration factors can result in significant, up to three orders of magnitude, errors in the calculated failure rate of capacitors. This paper analyzes deficiencies of the existing technique and recommends more accurate method of calculations. A physical model presenting failures of tantalum capacitors as time-dependent-dielectric-breakdown is used to determine voltage and temperature acceleration factors and select adequate Weibull grading test conditions. This model is verified by highly accelerated life testing (HALT) at different temperature and voltage conditions for three types of solid chip tantalum capacitors. It is shown that parameters of the model and acceleration factors can be calculated using a general log-linear relationship for the characteristic life with two stress levels.

  11. Influence of Electrolyte on ESR of Medium Voltage Wet Tantalum Capacitors

    Institute of Scientific and Technical Information of China (English)

    刘仲娥; 宋金荣; 陈晓静; 李忆莲; 桂娟

    2004-01-01

    In this paper, the influence of working electrolyte on high-frequency electrical performance of wet tantalum capacitors is studied. Emphasis is especially put on the study of the contribution of depolariser in reducing Equivalent Series Resistance(ESR). According to the theory of depolarization in electrochemistry and the theory of cathode capacitance of electrolytic capacitor, different kinds of depolarisers are added separately into the foregone electrolyte. Then capacitors are assembled with tantalum cores dipped with the compounded electrolytes. The best depolariser and its concentration in the whole electrolyte could be selected according to the test results of the capacitance and ESR of the capacitors. The results of our experiment show that depolariser Fe2(SO4)3 used in working electrolyte of 100 V/100 μF wet tantalum capacitors can help to obtain lower ESR and higher capacitance at frequency from 0.1 kHz to 100 kHz.

  12. Evaluation of Ferrite Chip Beads as Surge Current Limiters in Circuits with Tantalum Capacitors

    Science.gov (United States)

    Teverovsky, Alexander

    2014-01-01

    Limiting resistors are currently required to be connected in series with tantalum capacitors to reduce the risk of surge current failures. However, application of limiting resistors decreases substantially the efficiency of the power supply systems. An ideal surge current limiting device should have a negligible resistance for DC currents and high resistance at frequencies corresponding to transients in tantalum capacitors. This work evaluates the possibility of using chip ferrite beads (FB) as such devices. Twelve types of small size FBs from three manufacturers were used to evaluate their robustness under soldering stresses and at high surge current spikes associated with transients in tantalum capacitors. Results show that FBs are capable to withstand current pulses that are substantially greater than the specified current limits. However, due to a sharp decrease of impedance with current, FBs do not reduce surge currents to the required level that can be achieved with regular resistors.

  13. An exploration in mineral supply chain mapping using tantalum as an example

    Science.gov (United States)

    Soto-Viruet, Yadira; Menzie, W. David; Papp, John F.; Yager, Thomas R.

    2013-01-01

    This report uses the supply chain of tantalum (Ta) to investigate the complexity of mineral and metal supply chains in general and show how they can be mapped. A supply chain is made up of all the manufacturers, suppliers, information networks, and so forth, that provide the materials and parts that go into making up a final product. The mineral portion of the supply chain begins with mineral material in the ground (the ore deposit); extends through a series of processes that include mining, beneficiation, processing (smelting and refining), semimanufacture, and manufacture; and continues through transformation of the mineral ore into concentrates, refined mineral commodities, intermediate forms (such as metals and alloys), component parts, and, finally, complex products. This study analyses the supply chain of tantalum beginning with minerals in the ground to many of the final goods that contain tantalum.

  14. Experimental lumbar spine fusion with novel tantalum-coated carbon fiber implant

    DEFF Research Database (Denmark)

    Li, Haisheng; Zou, Xuenong; Woo, Charlotte

    2007-01-01

    the possibility of coating a biocompatible metal layer on top of the carbon fiber material, to improve its biological performance. Tantalum was chosen because of its bone compatibility, based on our previous studies. A novel spinal fusion cage was fabricated by applying a thin tantalum coating on the surface...... of carbon-carbon composite material through chemical vapor deposition. Mechanical and biological performance was tested in vitro and in vivo. Compress strength was found to be 4.9 kN (SD, 0.2). Fatigue test with 500,000 cycles was passed. In vitro radiological evaluation demonstrated good compatibility...... and newly formed bone. No inflammatory cells were found around the implant. Cages packed with two different graft materials (autograft and COLLOSS) achieved the same new bone formation. The present study proved that coating tantalum on top of the carbon-based implant is feasible, and good bone integration...

  15. Optical properties of d.c. magneto sputtered tantalum and titanium nanostructure thin film metal hydrides

    Indian Academy of Sciences (India)

    M Singh; S Srivastava; S Agarwal; S Kumar; Y K Vijay

    2010-10-01

    Nanostructured thin films of tantalum and titanium were deposited on glass substrate using d.c. magnetron sputtering technique under the argon gas environment at a pressure of 0.1 mbar. Optical transmission and absorption studies were carried out for these samples with pressure of hydrogen. Large changes in both transmission and absorption on loading these films with hydrogen are accompanied by significant phase changes and electronic transformation. Optical photograph shows the colour variation after hydrogenation in case of tantalum film which may be used as decorative mirrors and hydrogen sensors. The hydrogen storage capability of thin films was confirmed by variation in optical properties.

  16. Rapid synthesis of tantalum oxide dielectric films by microwave microwave-assisted atmospheric chemical vapor deposition

    Energy Technology Data Exchange (ETDEWEB)

    Ndiege, Nicholas [School of Chemical Sciences, University of Illinois at Urbana-Champaign, 600 South Mathews Avenue, Urbana, IL 61801 (United States)], E-mail: ndiege@uiuc.edu; Subramanian, Vaidyanathan [School of Chemical Sciences, University of Illinois at Urbana-Champaign, 600 South Mathews Avenue, Urbana, IL 61801 (United States)], E-mail: ravisv@unr.edu; Shannon, Mark A. [Mechanical Science and Engineering, University of Illinois at Urbana-Champaign, 1206 West Green street, Urbana, IL 61801 (United States)], E-mail: mshannon@uiuc.edu; Masel, Richard I. [School of Chemical Sciences, University of Illinois at Urbana-Champaign, 600 South Mathews Avenue, Urbana, IL 61801 (United States)], E-mail: r-masel@uiuc.edu

    2008-10-01

    Microwave-assisted chemical vapor deposition has been used to generate high quality, high-k dielectric films on silicon at high deposition rates with film thicknesses varying from 50 nm to 110 {mu}m using inexpensive equipment. Characterization of the post deposition products was performed by scanning electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, Auger electron spectroscopy and Raman spectroscopy. Film growth was determined to occur via rapid formation and accumulation of tantalum oxide clusters from tantalum (v) ethoxide (Ta(OC{sub 2}H{sub 5}){sub 5}) vapor on the deposition surface.

  17. Evaluation of wet tantalum capacitors after exposure to extended periods of ripple current, volume 2

    Science.gov (United States)

    Ward, C. M.

    1975-01-01

    The application of tantalum capacitors in the Viking Lander includes dc voltage and ripple current electrical stress, high temperature during nonoperating times (sterilization), and high vibration and shock loads. The capacitors must survive these severe environments without any degradation if reliable performance is to be achieved. A test program was established to evaluate both wet-slug tantalum and wet-foil capacitors under conditions accurately duplicating actual Viking applications. Test results of the electrical performance characteristics during extended periods of ripple current, the characteristics of the internal silver migration as a function of extended periods of ripple current, and the existence of any memory characteristics are presented.

  18. Evaluation of wet tantalum capacitors after exposure to extended periods of ripple current, volume 1

    Science.gov (United States)

    Watson, G. W.; Lasharr, J. C.; Shumaker, M. J.

    1974-01-01

    The application of tantalum capacitors in the Viking Lander includes both dc voltage and ripple current electrical stress, high temperature during nonoperating times (sterilization), and high vibration and shock loads. The capacitors must survive these severe environments without any degradation if reliable performance is to be achieved. A test program was established to evaluate both wet-slug tantalum and wet-foil capacitors under conditions accurately duplicating actual Viking applications. Test results of the electrical performance characteristics during extended periods of ripple current, the characteristics of the internal silver migration as a function for extended periods of ripple current, and the existence of any memory characteristics are presented.

  19. Biological Response of Human Bone Marrow-Derived Mesenchymal Stem Cells to Commercial Tantalum Coatings with Microscale and Nanoscale Surface Topographies

    Science.gov (United States)

    Skoog, Shelby A.; Kumar, Girish; Goering, Peter L.; Williams, Brian; Stiglich, Jack; Narayan, Roger J.

    2016-06-01

    Tantalum is a promising orthopaedic implant coating material due to its robust mechanical properties, corrosion resistance, and excellent biocompatibility. Previous studies have demonstrated improved biocompatibility and tissue integration of surface-treated tantalum coatings compared to untreated tantalum. Surface modification of tantalum coatings with biologically inspired microscale and nanoscale features may be used to evoke optimal tissue responses. The goal of this study was to evaluate commercial tantalum coatings with nanoscale, sub-microscale, and microscale surface topographies for orthopaedic and dental applications using human bone marrow-derived mesenchymal stem cells (hBMSCs). Tantalum coatings with different microscale and nanoscale surface topographies were fabricated using a diffusion process or chemical vapor deposition. Biological evaluation of the tantalum coatings using hBMSCs showed that tantalum coatings promote cellular adhesion and growth. Furthermore, hBMSC adhesion to the tantalum coatings was dependent on surface feature characteristics, with enhanced cell adhesion on sub-micrometer- and micrometer-sized surface topographies compared to hybrid nano-/microstructures. Nanostructured and microstructured tantalum coatings should be further evaluated to optimize the surface coating features to promote osteogenesis and enhance osseointegration of tantalum-based orthopaedic implants.

  20. Decay heat calculations for a 500 kW W–Ta spallation target

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Quanzhi, E-mail: qzhyu@iphy.ac.cn [Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, Beijing 100190 (China); Lu, Youlian; Hu, Zhiliang; Zhou, Bin [Dongguan Campus, Institute of High Energy Physics, Chinese Academy of Sciences, Dongguan 523800 (China); Dongguan Neutron Science Center, Dongguan 523800 (China); Yin, Wen; Liang, Tianjiao [Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, Beijing 100190 (China)

    2015-05-15

    The China Spallation Neutron Source (CSNS) is a short-pulsed neutron scattering facility. The beam power is designed to be 100 kW in Phase I, with the capability of upgrading to 500 kW. Tantalum (Ta)-cladded tungsten (W) was chosen as the spallation target due to its high neutron yield. Ta claddings can solve the problem of the corrosiveness of W plates, although they produce high decay heat after intense irradiation. This paper presents the decay heat distributions and evolutions for the future upgraded 500 kW W–Ta spallation target. The calculations are performed using the MCNPX2.5 Monte Carlo code and the CINDER’90 activation code. The decay heat distributions show that for the W plates, decay heat is mainly produced via the spallation reaction process, whereas for the Ta claddings, it is mainly produced via the neutron capture process. An effective method of reducing the decay heat in the W–Ta target is also presented and discussed.

  1. Irradiation damage

    Energy Technology Data Exchange (ETDEWEB)

    Howe, L.M

    2000-07-01

    There is considerable interest in irradiation effects in intermetallic compounds from both the applied and fundamental aspects. Initially, this interest was associated mainly with nuclear reactor programs but it now extends to the fields of ion-beam modification of metals, behaviour of amorphous materials, ion-beam processing of electronic materials, and ion-beam simulations of various kinds. The field of irradiation damage in intermetallic compounds is rapidly expanding, and no attempt will be made in this chapter to cover all of the various aspects. Instead, attention will be focused on some specific areas and, hopefully, through these, some insight will be given into the physical processes involved, the present state of our knowledge, and the challenge of obtaining more comprehensive understanding in the future. The specific areas that will be covered are: point defects in intermetallic compounds; irradiation-enhanced ordering and irradiation-induced disordering of ordered alloys; irradiation-induced amorphization.

  2. Analytical fingerprint for tantalum ores from African deposits

    Science.gov (United States)

    Melcher, F.; Graupner, T.; Sitnikova, M.; Oberthür, T.; Henjes-Kunst, F.; Gäbler, E.; Rantitsch, G.

    2009-04-01

    Illegal mining of gold, diamonds, copper, cobalt and, in the last decade, "coltan" has fuelled ongoing armed conflicts and civil war in a number of African countries. Following the United Nations initiative to fingerprint the origin of conflict materials and to develop a traceability system, our working group is investigating "coltan" (i.e. columbite-tantalite) mineralization especially in Africa, also within the wider framework of establishing certified trading chains (CTC). Special attention is directed towards samples from the main Ta-Nb-Sn provinces in Africa: DR Congo, Rwanda, Mozambique, Ethiopia, Egypt and Namibia. The following factors are taken into consideration in a methodological approach capable of distinguishing the origin of tantalum ores and concentrates with the utmost probability: (1) Quality and composition of coltan concentrates vary considerably. (2) Mineralogical and chemical compositions of Ta-Nb ores are extremely complex due to the wide range of the columbite-tantalite solid solution series and its ability to incorporate many additional elements. (3) Coltan concentrates may contain a number of other tantalum-bearing minerals besides columbite-tantalite. In our approach, coltan concentrates are analyzed in a step-by-step mode. State-of-the-art analytical tools employed are automated scanning electron microscopy (Mineral Liberation Analysis; MLA), electron microprobe analysis (major and trace elements), laser ablation-ICP-MS (trace elements, isotopes), and TIMS (U-Pb dating). Mineral assemblages in the ore concentrates, major and trace element concentration patterns, and zoning characteristics in the different pegmatites from Africa distinctly differ from each other. Chondrite-normalized REE distribution patterns vary significantly between columbite, tantalite, and microlite, and also relative to major element compositions of columbites. Some locations are characterized by low REE concentrations, others are highly enriched. Samples with

  3. Exploring the effect of boron and tantalum codoping on the enhanced photocatalytic activity of TiO{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Gong, Yinyan, E-mail: ygong2007@163.com; Fu, Chengxin; Ting, Lv; Chenu, Jingru; Zhao, Qinger; Li, Can

    2015-10-01

    Graphical abstract: B and Ta codoped sample was prepared by a sol–gel method, which exhibits the best photocatalytic performance on degradation of methylene blue solution under a simulated solar light source in comparison with undoped and singly doped TiO{sub 2} nanocrystals. The enhancement was tentatively attributed to: (1) the increase of free electron concentrations by substituting Ti{sup 4+} with Ta{sup 5+} species, as well as the prolonged carrier lifetime due to the complex structures formed by Bint, Ta{sup 5+}, and doping-induced defects; (2) redshift of optical absorption edge due to the presence of B species at interstitial sites, and (3) reduction of average crystallite size. - Highlights: • Boron and tantalum codoped TiO{sub 2} photocatalyts were prepared by a sol–gel method. • XRD and Raman measurements confirmed that all the TiO{sub 2} nanocyrstals are anatase structure. • Ta in the form of Ta{sup 5+} and interstitial B and substitutional B are detected by XPS observations. • (B, Ta)-codoped sample has the best efficiency compared to pure and singly doped catalysts. - Abstract: Aiming to improve the photocatalytic activity, boron and tantalum co-doped TiO{sub 2} nanocrystals were prepared by a sol–gel method. Pure and doped titania samples were characterized by X-ray diffraction (XRD) measurements, Raman spectroscopy, X-ray photoelectron spectroscopy (XPS) and UV–vis diffuse reflectance spectroscopy. The results revealed that all the samples have highly crystalline anatase structure, and no any other second phase was observed. It is found that the incorporation of dopants inhibits the growth of TiO{sub 2} nanocrystal. Moreover, XPS observations showed that Ta are in the form of Ta{sup 5+} while the majority of B species are present at interstitial sites. Finally, photocatalytic activities of all the samples were evaluated by degradation of methylene blue (MB) solutions under simulated solar light irradiation. Ta-doped and (B, Ta

  4. 高速气流中激光加热平板数值模拟与分析%Numerical simulation of plane target in airflow under laser irradiation

    Institute of Scientific and Technical Information of China (English)

    胡鹏; 陈发良

    2011-01-01

    A model of a plane target under laser irradiation is used to numerically simulate the temperature distribution in different speed airflow, using the thermal coupling method of gas and solid. The results show that there is a higher equilibrium temperature over the plane target when there is no laser irradiation, and the heat transfer coefficient between air and the plane tar-get increases with the airflow speed; with a maximum value occurring at the front edge of the target, it declines along the target length. When under laser irradiation in different cases, the temperature distribution in the plane is analyzed carefully, and the in-fluence of aerodynamic heating, forced convection cooling and laser heating is focused to compare their thermal competition,which shows that the temperature distributions in the target results from several thermal competition ultimately.%采用流固耦合方法,数值模拟了高速流场中激光作用下来流速度对平板温度分布的影响.结果表明:无激光辐照时,高速气流中平板有较高的气动生热平衡温度,且平板-气流之间的换热系数随来流速度增大而增大;在平板前沿换热系数增长最快,沿平板长度方向增速趋于平缓.分析了激光辐照时高速气流中激光加热平板的温度分布情况,考察了来流速度不同时,气动生热、散热和激光辐照对平板温度的影响,给出了激光辐照后的温升情况和温度分布,分析了在不同速度来流下,对流散热、摩擦生热和激光加热之间的竞争关系,结果表明,平板温度具体分布主要是加热过程竞争的结果.

  5. Efficient multi-keV x-ray generation from a high-Z target irradiated with a clean ultra-short laser pulse.

    Science.gov (United States)

    Zhang, Z; Nishikino, M; Nishimura, H; Kawachi, T; Pirozhkov, A S; Sagisaka, A; Orimo, S; Ogura, K; Yogo, A; Okano, Y; Ohshima, S; Fujioka, S; Kiriyama, H; Kondo, K; Shimomura, T; Kanazawa, S

    2011-02-28

    Kα line emissions from Mo and Ag plates were experimentally studied using clean, ultrahigh-intensity femtosecond laser pulses. The absolute yields of Kα x-rays at 17 keV from Mo and 22 keV from Ag were measured as a function of the laser pulse contrast ratio and irradiation intensity. Significantly enhanced Kα yields were obtained for both Mo and Ag by employing high contrast ratios and irradiances. Conversion efficiencies of 4.28×10⁻⁵/sr for Mo and 4.84×10⁻⁵/sr for Ag, the highest values obtained to date, were demonstrated with contrast ratios in the range 10⁻¹⁰ to 10⁻¹¹.

  6. Tantalum (oxy)nitrides nanotube arrays for the degradation of atrazine in vis-Fenton-like process.

    Science.gov (United States)

    Du, Yingxun; Zhao, Lu; Chang, Yuguang; Su, Yaling

    2012-07-30

    In order to overcome the limitation of the application of nanoparticles, tantalum (oxy)nitrides nanotube arrays on a Ta foil were synthesized and introduced in vis (visible light)-Fenton-like system to enhance the degradation of atrazine. At first, the anodization of tantalum foil in a mild electrolyte solution containing ethylene glycol and water (v:v=2:1) plus 0.5wt.% NH(4)F produced tantala nanotubes with an average diameter of 30nm and a length of approximately 1μm. Then the nitridation of tantala nanotube arrays resulted in the replacement of N atoms to O atoms to form tantalum (oxy)nitrides (TaON and Ta(3)N(5)), as testified by XRD and XPS analyses. The synthesized tantalum (oxy)nitrides nanotubes absorb well in the visible region up to 600nm. Under visible light, tantalum (oxy)nitrides nanotube arrays were catalytically active for Fe(3+) reduction. With tantalum (oxy)nitrides nanotube arrays, the degradation of atrazine and the formation of the intermediates in vis/Fe(3+)/H(2)O(2) system were significantly accelerated. This was explained by the higher concentration of Fe(2+) and thus the faster decomposition of H(2)O(2) with tantalum (oxy)nitrides nanotubes. In addition, tantalum (oxy)nitrides nanotubes exhibited stable performance during atrazine degradation for three runs. The good performance and stability of the tantalum (oxy)nitrides nanotubes film with the convenient separation, suggest that this film is a promising catalyst for vis-Fenton-like degradation.

  7. Founder of Niobium-Tantalum Granite Deposit——Li Renke

    Institute of Scientific and Technical Information of China (English)

    1993-01-01

    Li Renke, Vice director of Nonferrous Metals Geological Research Institute of Guangxi, Senior Engineer, discovered a new type of niobium-tantalum granite deposit as his major contribution and made significant progress in ore exploration of this type of ore deposit.

  8. Effect of pH on the Electrochemical Behavior of Tantalum in Borate Buffer Solutions

    Science.gov (United States)

    Attarzadeh, F. R.; Attarzadeh, N.; Vafaeian, S.; Fattah-Alhosseini, A.

    2016-10-01

    In this research, various electrochemical methods were used to investigate the electrochemical behavior of tantalum in borate buffer solutions of various pH values, ranging from 9.0 to 6.5. Potentiodynamic polarization curves revealed that tantalum showed excellent passive behavior in borate buffer solutions. The potentiodynamic polarization and electrochemical impedance spectroscopy results showed that the passive film formed on tantalum offered its best protective behavior when the pH is 8.0, with the passivity undergoing a drastic change as the pH moved toward higher values. The semiconductive behavior of the passive films formed on tantalum was investigated by employing Mott-Schottky analysis in conjunction with a point defect model. The results indicated that the passive film exhibited n-type semiconductive behavior and that donor densities were in the range of 1.958-7.242 × 1020 cm-3. Moreover, this analysis showed that the donor density and flat band potential were quite sensitive to the pH.

  9. Morphology, proliferation, and osteogenic differentiation of mesenchymal stem cells cultured on titanium, tantalum, and chromium surfaces

    DEFF Research Database (Denmark)

    Stiehler, Maik; Lind, M.; Mygind, Tina;

    2007-01-01

    the interactions between human mesenchymal stem cells (MSCs) and smooth surfaces of titanium (Ti), tantalum (Ta), and chromium (Cr). Mean cellular area was quantified using fluorescence microscopy (4 h). Cellular proliferation was assessed by (3)H-thymidine incorporation and methylene blue cell counting assays (4...

  10. Transmittance and Refractive Index of the Lanthanum Strontium Aluminium Tantalum Oxide Crystal

    Institute of Scientific and Technical Information of China (English)

    HU Bo-Qing; WANG Xiao-Ming; ZHOU Tang; ZHAO Zong-Yuan; WU Xing; CHEN Xiao-Long

    2001-01-01

    The lanthanum strontium aluminium tantalum oxide (LSAT) crystal is grown by means of a floating or pulling method. Its optical transmittance, refractive indices in visible and near-infrared areas and its dispersion curve are reported. The transparence range of LSAT is from 0.45 to 4.2μm and its refractive index is 2.0244.

  11. Tantalum-modified Stellite 6 thick coatings : microstructure and mechanical performance

    NARCIS (Netherlands)

    Farnia, A.; Ghaini, F. Malek; Rao, J. C.; Ocelik, V.; De Hosson, J. Th. M.

    2013-01-01

    Thick Co-based coatings with different contents of tantalum were prepared by simultaneous powder feeding laser cladding technique on 304 stainless steel substrate, with the Ta wt% being 0, 2, 7 and 12. Laser processing was carried out with a continuous 3.3 kW Yt:YAG fiber laser. Microstructural obse

  12. Electrosynthesis of tantalum borides in oxygen-free and oxygen-containing fluoride melts

    DEFF Research Database (Denmark)

    Polyakova, L.P.; Polyakov, E.G.; Makarova, O.V.;

    2001-01-01

    Results of electrosynthesis of tantalum borides in fluoride and oxyfluoride melts are compared. It is shown that the single-phase X-ray-amorphous micro-layered coatings form only in the latter case. Linear and square-wave voltammetry, complemented by X-ray diffraction analysis, IR spectroscopy...

  13. The effects of argon ion bombardment on the corrosion resistance of tantalum

    Science.gov (United States)

    Ramezani, A. H.; Sari, A. H.; Shokouhy, A.

    2017-02-01

    Application of ion beam has been widely used as a surface modification method to improve surface properties. This paper investigates the effect of argon ion implantation on surface structure as well as resistance against tantalum corrosion. In this experiment, argon ions with energy of 30 keV and in doses of 1 × 1017-10 × 1017 ions/cm2 were used. The surface bombardment with inert gases mainly produces modified topography and morphology of the surface. Atomic Force Microscopy was also used to patterned the roughness variations prior to and after the implantation phase. Additionally, the corrosion investigation apparatus wear was applied to compare resistance against tantalum corrosion both before and after ion implantation. The results show that argon ion implantation has a substantial impact on increasing resistance against tantalum corrosion. After the corrosion test, scanning electron microscopy (SEM) analyzed the samples' surface morphologies. In addition, the elemental composition is characterized by energy-dispersive X-ray (EDX) analysis. The purpose of this paper was to obtain the perfect condition for the formation of tantalum corrosion resistance. In order to evaluate the effect of the ion implantation on the corrosion behavior, potentiodynamic tests were performed. The results show that the corrosion resistance of the samples strongly depends on the implantation doses.

  14. Synthesis of Monodispersed Tantalum(V) oxide Nanospheres by an Ethylene Glycol Mediated Route

    Science.gov (United States)

    Tantalum(V) oxide (Ta2O5) nanospheres have been synthesized by a very simple ethylene glycol mediated route. The two-step process involves the formation of glycolate nanoparticles and their subsequent hydrolysis and calcination to generate the final Ta2O5 nanospheres. The synthes...

  15. Design, Development, manufacture and qualification of wet-slug all-tantalum capacitors

    Science.gov (United States)

    Maher, R. H.

    1977-01-01

    Specifications and qualification tests data are presented for over eleven hundred T3 case all-tantalum capacitors encompassing four ratings. The finalized product has all the advantages of the silver cased wet and is capable of withstanding some reverse potential ac ripple current.

  16. Deformation of Cases in High Capacitance Value Wet Tantalum Capacitors under Environmental Stresses

    Science.gov (United States)

    Teverovsky, Alexander

    2016-01-01

    Internal gas pressure in hermetic wet tantalum capacitors is created by air, electrolyte vapor, and gas generated by electrochemical reactions at the electrodes. This pressure increases substantially with temperature and time of operation due to excessive leakage currents. Deformation of the case occurs when the internal pressure exceeds pressure of the environments and can raise significantly when a part operates in space. Contrary to the cylinder case wet tantalum capacitors that have external sealing by welding and internal sealing provided by the Teflon bushing and crimping of the case, no reliable internal sealing exists in the button case capacitors. Single seal design capacitors are used for high capacitance value wet tantalum capacitors manufactured per DLA L&M drawings #04003, 04005, and 10011, and require additional analysis to assure their reliable application in space systems. In this work, leakage currents and case deformation of button case capacitors were measured during different environmental test conditions. Recommendations for derating, screening and qualification testing are given. This work is a continuation of a series of NEPP reports related to quality and reliability of wet tantalum capacitors.

  17. Complex-Mediated Synthesis of Tantalum Oxyfluoride Hierarchical Nanostructures for Highly Efficient Photocatalytic Hydrogen Evolution.

    Science.gov (United States)

    Xu, Leilei; Gong, Haotian; Deng, Li; Long, Fei; Gu, Yu; Guan, Jianguo

    2016-04-13

    In this work, we have, for the first time, developed a facile wet-chemical route to obtain a novel photocatalytic material of tantalum oxyfluoride hierarchical nanostructures composed of amorphous cores and single crystalline TaO2F nanorod shells (ACHNs) by regulating the one-step hydrothermal process of TaF5 in a mixed solution of isopropanol (i-PrOH) and H2O. In this approach, elaborately controlling the reaction temperature and volume ratio of i-PrOH and H2O enabled TaF5 to transform into intermediate coordination complex ions of [TaOF3·2F](2-) and [TaF7](2-), which subsequently produced tantalum oxyfluoride ACHNs via a secondary nucleation and growth due to a stepwise change in hydrolysis rates of the two complex ions. Because of the unique chemical composition, crystal structure and micromorphology, the as-prepared tantalum oxyfluoride ACHNs show a more negative flat band potential, an accelerated charge transfer, and a remarkable surface area of 152.4 m(2) g(-1) contributing to increased surface reaction sites. As a result, they exhibit a photocatalytic activity for hydrogen production up to 1.95 mmol h(-1) g(-1) under the illumination of a simulated solar light without any assistance of co-catalysts, indicating that the as-prepared tantalum oxyfluoride ACHNs are a novel promising photocatalytic material for hydrogen production.

  18. Electrosynthesis of tantalum borides in oxygen-free and oxygen-containing fluoride melts

    DEFF Research Database (Denmark)

    Polyakova, L.P.; Polyakov, E.G.; Makarova, O.V.

    2001-01-01

    Results of electrosynthesis of tantalum borides in fluoride and oxyfluoride melts are compared. It is shown that the single-phase X-ray-amorphous micro-layered coatings form only in the latter case. Linear and square-wave voltammetry, complemented by X-ray diffraction analysis, IR spectroscopy...

  19. Effect of Compressive Stresses on Leakage Currents in Microchip Tantalum Capacitors

    Science.gov (United States)

    Teverovsky, Alexander

    2012-01-01

    Microchip tantalum capacitors are manufactured using new technologies that allow for production of small size capacitors (down to EIA case size 0402) with volumetric efficiency much greater than for regular chip capacitors. Due to a small size of the parts and leadless design they might be more sensitive to mechanical stresses that develop after soldering onto printed wiring boards (PWB) compared to standard chip capacitors. In this work, the effect of compressive stresses on leakage currents in capacitors has been investigated in the range of stresses up to 200 MPa. Significant, up to three orders of magnitude, variations of currents were observed after the stress exceeds a certain critical level that varied from 10 MPa to 180 MPa for capacitors used in this study. A stress-induced generation of electron traps in tantalum pentoxide dielectric is suggested to explain reversible variations of leakage currents in tantalum capacitors. Thermo-mechanical characteristics of microchip capacitors have been studied to estimate the level of stresses caused by assembly onto PWB and assess the risk of stress-related degradation and failures. Keywords: tantalum capacitors, leakage current, soldering, reliability, mechanical stress.

  20. Effect of oxygen deficiency on electronic properties and local structure of amorphous tantalum oxide thin films

    Energy Technology Data Exchange (ETDEWEB)

    Denny, Yus Rama [Department of Physics Education, University of Sultan Ageng Tirtayasa, Banten 42435 (Indonesia); Firmansyah, Teguh [Department of Electrical Engineering, University of Sultan Ageng Tirtayasa, Banten 42435 (Indonesia); Oh, Suhk Kun [Department of Physics, Chungbuk National University, Cheongju 28644 (Korea, Republic of); Kang, Hee Jae, E-mail: hjkang@cbu.ac.kr [Department of Physics, Chungbuk National University, Cheongju 28644 (Korea, Republic of); Yang, Dong-Seok [Department of Physics Education, Chungbuk National University, Cheongju 28644 (Korea, Republic of); Heo, Sung; Chung, JaeGwan; Lee, Jae Cheol [Analytical Engineering Center, Samsung Advanced Institute of Technology, Suwon 16678 (Korea, Republic of)

    2016-10-15

    Highlights: • The effect of oxygen flow rate on electronic properties and local structure of tantalum oxide thin films was studied. • The oxygen deficiency induced the nonstoichiometric state a-TaOx. • A small peak at 1.97 eV above the valence band side appeared on nonstoichiometric Ta{sub 2}O{sub 5} thin films. • The oxygen flow rate can change the local electronic structure of tantalum oxide thin films. - Abstract: The dependence of electronic properties and local structure of tantalum oxide thin film on oxygen deficiency have been investigated by means of X-ray photoelectron spectroscopy (XPS), Reflection Electron Energy Loss Spectroscopy (REELS), and X-ray absorption spectroscopy (XAS). The XPS results showed that the oxygen flow rate change results in the appearance of features in the Ta 4f at the binding energies of 23.2 eV, 24.4 eV, 25.8, and 27.3 eV whose peaks are attributed to Ta{sup 1+}, Ta{sup 2+}, Ta{sup 3+}/Ta{sup 4+}, and Ta{sup 5+}, respectively. The presence of nonstoichiometric state from tantalum oxide (TaOx) thin films could be generated by the oxygen vacancies. In addition, XAS spectra manifested both the increase of coordination number of the first Ta-O shell and a considerable reduction of the Ta-O bond distance with the decrease of oxygen deficiency.

  1. Spatial and temporal changes in the morphology of preosteoblastic cells seeded on microstructured tantalum surfaces

    DEFF Research Database (Denmark)

    Justesen, Jørn; Lorentzen, M.; Andersen, L. K.

    2009-01-01

    It has been widely reported that surface morphology on the micrometer scale affects cell function as well as cell shape. In this study, we have systematically compared the influence of 13 topographically micropatterned tantalum surfaces on the temporal development of morphology, including spreadi...

  2. Separating the strengthening phase in nickel-cobalt alloys doped with tantalum

    Science.gov (United States)

    Shaipov, R. Kh.; Kerimov, E. Yu.; Slyusarenko, E. M.

    2017-02-01

    The hardness values of monophasic (fcc solid solution) and biphasic (fcc solid solution and separated phase) nickel-cobalt alloys doped with tantalum are determined using the Vickers method. Based on the resulting data, a composition-structure-hardness diagram is devised for the Co-Ni-Ta system.

  3. Tantalum (oxy)nitrides nanotube arrays for the degradation of atrazine in vis-Fenton-like process

    Energy Technology Data Exchange (ETDEWEB)

    Du, Yingxun, E-mail: yxdu@niglas.ac.cn [Nanjing Institute of Geography and Limnology, State Key Laboratory of Lake Science and Environment, Chinese Academy of Sciences, Nanjing 210008 (China); Zhao, Lu [Nanjing Institute of Geography and Limnology, State Key Laboratory of Lake Science and Environment, Chinese Academy of Sciences, Nanjing 210008 (China); Chang, Yuguang [School of Biochemical and Environmental Engineering, Nanjing Xiaozhuang Univeristy, Nanjing 211171 (China); Su, Yaling [Nanjing Institute of Geography and Limnology, State Key Laboratory of Lake Science and Environment, Chinese Academy of Sciences, Nanjing 210008 (China)

    2012-07-30

    Highlights: Black-Right-Pointing-Pointer Tantala nanotubes on a Ta foil were formed by anodization in a NH{sub 4}F-containing electrolyte. Black-Right-Pointing-Pointer Tantalum (oxy)nitrides nanotubes were active for Fe{sup 3+} reduction under visible light. Black-Right-Pointing-Pointer Atrazine degradation by {center_dot}OH was accelerated with tantalum (oxy)nitrides nanotubes. Black-Right-Pointing-Pointer Tantalum (oxy)nitrides nanotubes display stable performance for atrazine degradation. - Abstract: In order to overcome the limitation of the application of nanoparticles, tantalum (oxy)nitrides nanotube arrays on a Ta foil were synthesized and introduced in vis (visible light)-Fenton-like system to enhance the degradation of atrazine. At first, the anodization of tantalum foil in a mild electrolyte solution containing ethylene glycol and water (v:v = 2:1) plus 0.5 wt.% NH{sub 4}F produced tantala nanotubes with an average diameter of 30 nm and a length of approximately 1 {mu}m. Then the nitridation of tantala nanotube arrays resulted in the replacement of N atoms to O atoms to form tantalum (oxy)nitrides (TaON and Ta{sub 3}N{sub 5}), as testified by XRD and XPS analyses. The synthesized tantalum (oxy)nitrides nanotubes absorb well in the visible region up to 600 nm. Under visible light, tantalum (oxy)nitrides nanotube arrays were catalytically active for Fe{sup 3+} reduction. With tantalum (oxy)nitrides nanotube arrays, the degradation of atrazine and the formation of the intermediates in vis/Fe{sup 3+}/H{sub 2}O{sub 2} system were significantly accelerated. This was explained by the higher concentration of Fe{sup 2+} and thus the faster decomposition of H{sub 2}O{sub 2} with tantalum (oxy)nitrides nanotubes. In addition, tantalum (oxy)nitrides nanotubes exhibited stable performance during atrazine degradation for three runs. The good performance and stability of the tantalum (oxy)nitrides nanotubes film with the convenient separation, suggest that this film is

  4. Food irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Webb, T.

    1986-01-01

    The proposed use of gamma radiation from cobalt 60 and cesium 137 for food irradiation in the United Kingdom is discussed, with particular reference to the possible dangers and disadvantages to the safety and wholesomeness of the food.

  5. Synthesis of NPN-Coordinated Tantalum Alkyl Complexes and Their Hydrogenolysis: Isolation of a Terminal Tantalum Hydride Incorporating a Doubly Cyclometalated NPN Scaffold.

    Science.gov (United States)

    Batke, Sonja; Sietzen, Malte; Wadepohl, Hubert; Ballmann, Joachim

    2017-05-01

    The closely related benzylene-linked diaminophosphines PhP(CH2C6H4-o-NHPh)2 (AH2) and PhP(C6H4-o-CH2NHXyl)2 (BH2 with Xyl = 3,5-Me2C6H3) were employed for the synthesis of tantalum(V) alkyls, which were then studied with respect to hydrogenolysis. In the case of AH2, the tantalum trimethyl complex [Ta(A)Me3] (1) and the tantalum hydrocarbyl complex [Ta(A)(CH2SiMe3)(η(2)-EtC≡CEt)] (2) were prepared from the ligand's dilithium salt (A)Li2(diox). Upon hydrogenolysis of 1 and 2, the formation of methane and SiMe4, respectively, was observed, but well-defined tantalum hydrides could not be detected. In the case of BH2, the cyclometalated species [Ta(B*)(NMe2)2] (3 with B* = κ(4)-N,P,N,C-(PhP(C6H4-o-CH2NXyl)(C6H4-o-CHNXyl))(3-)) was isolated and converted to the corresponding diiodo species [Ta(B*)I2] (4). Treatment of 4 with LiCH2SiMe3 resulted in the isolation of the corresponding dialkyl complex [Ta(B*)(CH2SiMe3)2] (5), which was converted to the doubly cyclometalated monoalkyl complexes [Ta(B**)(CH2SiMe3)(PMe3)] (6 with B** = κ(5)-C,N,P,N,C-(PhP(C6H4-o-CHNXyl)2)(4-)) and [Ta(B**)(CH2SiMe3)(dmpe)] (7) via reaction with PMe3 and dmpe, respectively. In contrast to 5 and 6, 7 was found to react cleanly with dihydrogen to afford the corresponding terminal tantalum(V) hydride [Ta(B**)(H)(dmpe)] (8). Upon reaction of 7 with D2, the deuteride [Ta(d2-B**)(D)(dmpe)] (9) was obtained and found to contain deuterium atoms in the methine positions of both tantalaaziridine subunits. The partially deuterated derivatives [Ta(B**)(D)(dmpe)] (10) and [Ta(d2-B**)(H)(dmpe)] (11) were generated via reaction of 8 and 9 with PhSiD3 and PhSiH3, respectively. Prior to the addition of gaseous D2 or H2, no H/D scrambling was observed in 10 or 11, indicating that the exchange of the methine positions proceeds via addition of D2 or H2 across the tantalaaziridine Ta-C bonds.

  6. [Food irradiation].

    Science.gov (United States)

    Migdał, W

    1995-01-01

    A worldwide standard on food irradiation was adopted in 1983 by Codex Alimentarius Commission of the Joint Food Standard Programme of the Food and Agriculture Organization (FAO) of the United Nations and the World Health Organization (WHO). As a result, 41 countries have approved the use of irradiation for treating one or more food items and the number is increasing. Generally, irradiation is used to: food loses, food spoilage, disinfestation, safety and hygiene. The number of countries which use irradiation for processing food for commercial purposes has been increasing steadily from 19 in 1987 to 33 today. In the frames of the national programme on the application of irradiation for food preservation and hygienization an experimental plant for electron beam processing has been established in Institute of Nuclear Chemistry and Technology. The plant is equipped with a small research accelerator Pilot (19MeV, 1 kW) and an industrial unit Elektronika (10MeV, 10 kW). On the basis of the research there were performed at different scientific institutions in Poland, health authorities have issued permission for irradiation for: spices, garlic, onions, mushrooms, potatoes, dry mushrooms and vegetables.

  7. XPS STUDY ON DNA DAMAGE BY LOW-ENERGY ELECTRON IRRADIATION

    Energy Technology Data Exchange (ETDEWEB)

    Noh, Hyung Ah; Cho, Hyuck [Chungnam National University, Physics Department, Daejeon (Korea, Republic of)

    2011-12-15

    After the first report that electrons with sub-ionization energy of DNA could cause single strand breaks or double strand breaks to DNA, there have been various studies to investigate the mechanisms of DNA damage by low-energy electrons. In this paper, we examined the possibility of using X-ray photoelectron spectroscopy (XPS) to analyze the dissociation patterns of the molecular bonds by electron irradiation on DNA thin films and tried to establish the method as a general tool for studying the radiation damage of biomolecules by low energy electrons. For the experiment, pBR322 plasmid DNA solution was formed into the films on tantalum plates by lyophilization and was irradiated by 5-eV electrons. Un-irradiated and irradiated DNA films were compared and analyzed using the XPS technique.

  8. Poisoning Experiments Aimed at Discriminating Active and Less-Active Sites of Silica-Supported Tantalum Hydride for Alkane Metathesis

    KAUST Repository

    Saggio, Guillaume

    2010-10-04

    Only 50% of the silica-supported tantalum hydride sites are active in the metathesis of propane. Indeed, more than 45% of the tantalum hydride can be eliminated by a selective oxygen poisoning of inactive sites with no significant decrease in the global turnover. Conversely, cyclopentane induces no such selective poisoning. Hence, the active tantalum hydride sites that show greater resistance to oxygen poisoning correspond to the νTa-H bands of higher wavenumbers, particularly that at 1860cm-1. These active tantalum hydride sites should correspond to tris- or monohydride species relatively far from silica surface oxygen atoms. © 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  9. Analysis of cobalt, tantalum, titanium, vanadium and chromium in tungsten carbide by inductively coupled plasma-optical emission spectrometry

    CSIR Research Space (South Africa)

    Archer, M

    2003-12-01

    Full Text Available Inductively coupled plasma optical emission spectroscopy (ICP-OES) was used to measure the concentrations of cobalt, tantalum, titanium, vanadium and chromium in solutions of tungsten carbide. The main advantage of the method described here lies...

  10. Corrosion behavior of tantalum-coated cobalt-chromium modular necks compared to titanium modular necks in a simulator test.

    Science.gov (United States)

    Dorn, Ulrich; Neumann, Daniel; Frank, Mario

    2014-04-01

    This study compared the corrosion behavior of tantalum-coated cobalt-chromium modular necks with that of titanium alloy modular necks at their junction to titanium-alloy femoral stem. Tests were performed in a dry assembly and two wet assemblies, one contaminated with calf serum and the other contaminated with calf serum and bone particles. Whereas the titanium modular neck tested in the dry assembly showed no signs of corrosion, the titanium modular necks tested in both wet assemblies showed marked depositions and corrosive attacks. By contrast, the tantalum-coated cobalt-chromium modular necks showed no traces of corrosion or chemical attack in any of the three assemblies. This study confirms the protective effect of tantalum coating the taper region of cobalt-chromium modular neck components, suggesting that the use of tantalum may reduce the risk of implant failure due to corrosion.

  11. Preparation of Strontium Bismuth Tantalum (SBT) Fine Powder by Sol-Gel Process Using Bismuth Subnitrate as Bismuth Source

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Strontium bismuth tantalum (SBT) fine power was prepared by Sol-Gel method. Pentaethoxy tantalum, strontium acetate and bismuth subnitrate were used as raw materials, and were dissolved in proper order in ethylene glycol to form transparent sol. The mixed precursor was dried at 80°C and annealed at 800°C for 1 h. Crystallized nanometer sized SBT fine powder was obtained and characterized by XRD.

  12. 钽复合板设备制造技术%Fabrication Technology About Tantalum Composite Board Vessels

    Institute of Scientific and Technical Information of China (English)

    朱广前

    2012-01-01

    Bring forward methods about settling welding problems about the tantalum composite board vessels and cautions during the tantalum vessels welding and fabrication.%对钽材复合板焊接中容易出现的问题进行了详细介绍,并提出了钽材复合板热交换设备中常用的几种焊接接头形式.

  13. Sulfinylcalix[4]arene-impregnated amberlite XAD-7 resin for the separation of niobium(V) from tantalum(V).

    Science.gov (United States)

    Matsumiya, Hiroaki; Yasuno, Shizu; Iki, Nobuhiko; Miyano, Sotaro

    2005-10-07

    Amberlite XAD-7 resin was impregnated with p-tert-butylsulfinylcalix[4]arene. Niobium(V) was collected on the impregnated resin in yields of more than 90% around pH 5.4, whereas tantalum(V) was negligibly collected. The collected niobium(V) was desorbed with 9 M sulfuric acid nearly quantitatively, hence the separation of niobium(V) from tantalum(V) was successfully achieved.

  14. Composition and structure variation for magnetron sputtered tantalum oxynitride thin films, as function of deposition parameters

    Energy Technology Data Exchange (ETDEWEB)

    Cristea, D.; Pătru, M.; Crisan, A.; Munteanu, D. [Department of Materials Science, Transilvania University, 500036 Brasov (Romania); Crăciun, D. [Laser Department, National Institute for Laser, Plasma, and Radiation Physics, Magurele (Romania); Barradas, N.P. [Centro de Ciências e Tecnologias Nucleares, Instituto Superior Técnico, Universidade de Lisboa, E.N. 10 ao km 139,7, 2695-066 Bobadela LRS (Portugal); Alves, E. [Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade de Lisboa, E.N. 10 ao km 139,7, 2695-066 Bobadela LRS (Portugal); Apreutesei, M. [Université de Lyon, Institut des Nanotechnologies de Lyon INL-UMR 5270, CNRS, Ecole Centrale de Lyon, Ecully F-69134 (France); MATEIS Laboratory-INSA de Lyon, Bât. B. Pascal, 7 Avenue Jean Capelle, 69621 Villeurbanne Cedex (France); Moura, C. [Center of Physics, University of Minho, Campus de Gualtar, 4710-057 Braga (Portugal); Cunha, L., E-mail: lcunha@fisica.uminho.pt [Center of Physics, University of Minho, Campus de Gualtar, 4710-057 Braga (Portugal)

    2015-12-15

    Highlights: • Structural evolution from β-Ta, to fcc-Ta(O,N), to amorphous Ta{sub 2}O{sub 5} with increasing P(N{sub 2} + O{sub 2}). • The substrate bias influences the N content, but does not influence the O content of the films. • The structural features of the films appear at lower P(N{sub 2} + O{sub 2}) when produced with grounded substrate. - Abstract: Tantalum oxynitride thin films were produced by magnetron sputtering. The films were deposited using a pure Ta target and a working atmosphere with a constant N{sub 2}/O{sub 2} ratio. The choice of this constant ratio limits the study concerning the influence of each reactive gas, but allows a deeper understanding of the aspects related to the affinity of Ta to the non-metallic elements and it is economically advantageous. This work begins by analysing the data obtained directly from the film deposition stage, followed by the analysis of the morphology, composition and structure. For a better understanding regarding the influence of the deposition parameters, the analyses are presented by using the following criterion: the films were divided into two sets, one of them produced with grounded substrate holder and the other with a polarization of −50 V. Each one of these sets was produced with different partial pressure of the reactive gases P(N{sub 2} + O{sub 2}). All the films exhibited a O/N ratio higher than the N/O ratio in the deposition chamber atmosphere. In the case of the films produced with grounded substrate holder, a strong increase of the O content is observed, associated to the strong decrease of the N content, when P(N{sub 2} + O{sub 2}) is higher than 0.13 Pa. The higher Ta affinity for O strongly influences the structural evolution of the films. Grazing incidence X-ray diffraction showed that the lower partial pressure films were crystalline, while X-ray reflectivity studies found out that the density of the films depended on the deposition conditions: the higher the gas pressure, the

  15. The effects of tantalum on the microstructure of two polycrystalline nickel-base superalloys: B-1900 + Hf and MAR-M247

    Science.gov (United States)

    Janowski, G. M.; Heckel, R. W.; Pletka, B. J.

    1986-11-01

    Changes in the γ/γ'/carbide microstructure as a function of Ta content were studied in conventionally cast B-1900 + Hf and both conventionally cast and directionally solidified MAR-M247.* The effects of tantalum on the microstructure were found to be similar in both nickel-base superalloys. In particular, the γ' and carbide volume fractions increased approximately linearly with tantalum additions in both alloys. The γ' phase compositions did not change as tantalum additions were made with the exception of an increase in the tantalum level. Bulk tantalum additions increased the tantalum, chromium, and cobalt levels of the γ phase in both alloy series. The increase in the concentrations of the latter two elements was attributed to a decrease in the γ phase fraction with increasing bulk tantalum level and nearly constant γ' /γ partitioning ratios. It was demonstrated that the large increase in the γ ' volume fraction was a result of tantalum not affecting the partitioning ratios of the other alloying elements. The addition of tantalum led to a partial replacement of the hafnium in the MC carbides, although the degree of replacement was reduced by the solutionizing and aging heat treat-ment. In addition, chromium-rich M23C6 carbides formed as a result of MC carbide decomposition during heat treatment.

  16. Electrical-breakdown and electronic current of tantalum-tantalum oxide-aqueous electrolyte systems. [Ta sub 2 O sub 5

    Energy Technology Data Exchange (ETDEWEB)

    Kalra, K.C.; Katyal, P. (Dept. of Chemistry, Maharshi Dayanand Univ., Rohtak (India))

    1991-06-30

    Breakdown voltage and electronic current data for barrier anodic tantalum oxide films in contact with aqueous electrolytes of various concentrations and compositions at 298 K have been obtained. The influence of electrolyte concentration on breakdown characteristics can be broadly explained in terms of the Ikonopisov electron avalanche breakdown model. Albella and coworkers' theory explains the effect of electrolyte concentration for our results more explicitly. Various parameters of the Albella theory have been evaluated, and their dependence on electrolyte concentration has been studied. The dependence of breakdown voltage on electrolyte concentration has also been discussed in the light of the theory of Di Quarto and coworkers. (orig.).

  17. Influence of the reactive atmosphere on the formation of nanoparticles in the plasma plume induced by nanosecond pulsed laser irradiation of metallic targets at atmospheric pressure and high repetition rate

    Energy Technology Data Exchange (ETDEWEB)

    Girault, M. [Laboratoire Interdisciplinaire Carnot de Bourgogne, UMR 6303 CNRS-Univ. Bourgogne Franche-Comté, 9 Av. A. Savary, BP 47 870, F-21078 Dijon Cedex (France); Le Garrec, J.-L.; Mitchell, J.B.A. [Institut de Physique de Rennes, UMR 6251 CNRS-Université de Rennes 1, 35042 Rennes Cedex (France); Jouvard, J.-M. [Laboratoire Interdisciplinaire Carnot de Bourgogne, UMR 6303 CNRS-Univ. Bourgogne Franche-Comté, 9 Av. A. Savary, BP 47 870, F-21078 Dijon Cedex (France); Carvou, E. [Institut de Physique de Rennes, UMR 6251 CNRS-Université de Rennes 1, 35042 Rennes Cedex (France); Menneveux, J.; Yu, J. [Institut Lumière Matière, UMR5306 Université Lyon 1-CNRS, Université de Lyon, 69622 Villeurbanne Cedex (France); Ouf, F.-X. [Institut de Radioprotection et de Sureté Nucléaire IRSN/PSN-RES/SCA/LPMA BP 68, 91192 Gif-Sur-Yvette (France); Carles, S. [Institut de Physique de Rennes, UMR 6251 CNRS-Université de Rennes 1, 35042 Rennes Cedex (France); Potin, V.; Pillon, G.; Bourgeois, S. [Laboratoire Interdisciplinaire Carnot de Bourgogne, UMR 6303 CNRS-Univ. Bourgogne Franche-Comté, 9 Av. A. Savary, BP 47 870, F-21078 Dijon Cedex (France); Perez, J. [Synchrotron SOLEIL, L’Orme des Merisiers, Saint-Aubin, F-91192 Gif-sur-Yvette Cedex (France); Marco de Lucas, M.C., E-mail: delucas@u-bourgogne.fr [Laboratoire Interdisciplinaire Carnot de Bourgogne, UMR 6303 CNRS-Univ. Bourgogne Franche-Comté, 9 Av. A. Savary, BP 47 870, F-21078 Dijon Cedex (France); and others

    2016-06-30

    Highlights: • NPs formed in a plasma-plume during laser irradiation of metals (Al, Ti, Ag) were studied. • In situ SAXS and ex situ TEM, XRD and Raman spectra were measured. • NPs size decreased when increasing the O{sub 2} fraction in a controlled O{sub 2}+N{sub 2} atmosphere. • The oxidation of metal NPs in the plasma restricts the increase of the size of the NPs. - Abstract: The influence of a reactive atmosphere on the formation of nanoparticles (NPs) in the plasma plume generated by nanosecond pulsed laser irradiation of metal targets (Ti, Al, Ag) was probed in situ using Small Angle X-ray Scattering (SAXS). Air and different O{sub 2}–N{sub 2} gas mixtures were used as reactive gas within atmospheric pressure. SAXS results showed the formation of NPs in the plasma-plume with a mean radius varying in the 2–5 nm range. A decrease of the NPs size with increasing the O{sub 2} percentage in the O{sub 2}–N{sub 2} gas mixture was also showed. Ex situ observations by transmission electron microscopy and structural characterizations by X-ray diffraction and Raman spectroscopy were also performed for powders collected in experiments done using air as ambient gas. The stability of the different metal oxides is discussed as being a key parameter influencing the formation of NPs in the plasma-plume.

  18. Highly conformal atomic layer deposition of tantalum oxide using alkylamide precursors

    Energy Technology Data Exchange (ETDEWEB)

    Hausmann, Dennis M.; Rouffignac, Philippe de; Smith, Amethyst; Gordon, Roy; Monsma, Douwe

    2003-10-22

    Atomic layer deposition of highly conformal films of tantalum oxide were studied using tantalum alkylamide precursors and water as the oxygen source. These films also exhibited a very high degree of conformality: 100% step coverage on vias with aspect ratios greater than 35. As deposited, the films were free of detectable impurities with the expected (2.5-1) oxygen to metal ratio and were smooth and amorphous. The films were completely uniform in thickness and composition over the length of the reactor used for depositions. Films were deposited at substrate temperatures from 50 to 350 deg. C from precursors that were vaporized at temperatures from 50 to 120 deg. C. As deposited, the films showed a dielectric constant of 28 and breakdown field consistently greater than 4.5 MV/cm.

  19. Electron-microscopic examination of the transition zone of aluminum-tantalum bimetallic joints (explosion welding)

    Science.gov (United States)

    Volkova, A. Yu.; Greenberg, B. A.; Ivanov, M. A.; Elkina, O. A.; Inozemtsev, A. V.; Plotnikov, A. V.; Patselov, A. M.; Kozhevnikov, V. E.

    2014-04-01

    A study of the structure of an aluminum-tantalum joint and a comparison of this structure with the structures of iron-silver and copper-tantalum joints have revealed the following processes of the interpenetration of the materials that occur during explosion welding: the formation of protrusions, the injection of particles of one material into the other, and the formation of zones of local melting. Regardless of the mutual solubility of the metals being welded, two types of fragmentation occur, i.e., (1) a granulating fragmentation (GF), which includes the formation, explosion-governed (EG) dispersion, and partial consolidation of particles, and (2) the fragmentation that is usually observed during severe plastic deformation. It is important that this traditional fragmentation is not accompanied by the formation and EG dispersion of particles. This feature allows one to easily distinguish these types of fragmentation (traditional and GF fragmentation).

  20. The list of tantalum lines for wavelengths calibration of the Hamilton echelle-spectrograph

    CERN Document Server

    Pakhomov, Yu V

    2015-01-01

    We present solution of the problem of wavelength calibration for Hamilton Echelle spectrograph using hollow cathode lamp, which was operated at Lick Observatory Shane telescope before June 9, 2011. The spectrum of the lamp claimed to be thorium-argon, contains, in addition to the lines of thorium and argon, a number of the unrecognized lines identified by us with tantalum. Using atomic data for measured lines of tantalum and thorium, we estimated the temperature of the gas in the lamp as T=3120+/-60 K. From the atomic line database VALD3 we selected all lines of TaI and TaII which can be seen in the spectrum of the lamp and compiled a list for the use in the processing of spectral observations. We note a limitation of the accuracy of calibration due to the influence of the hyperfine line splitting.

  1. Chemical systems for electrochemical mechanical planarization of copper and tantalum films

    Science.gov (United States)

    Muthukumaran, Ashok Kumar

    Electro-Chemical Mechanical Planarization (ECMP) is a new and highly promising technology just reaching industrial application; investigation of chemistries, consumables, and tool/control approaches are needed to overcome technological limitations. Development of chemical formulations for ECMP presents several challenges. Unlike conventional CMP, formulations for ECMP may not need an oxidant. Organic additives, especially inhibitors used to control planarity (i.e. to protect recessed regions), need to be stable under applied anodic potential. To have a high current efficiency, the applied current should not induce decomposition of the formulations. In addition, to enable clearing of the copper film, the interactions between multiple exposed materials (barrier material as well as copper) must be considered. Development of a full sequence ECMP process would require the removal of the barrier layer as well. Chemical systems that exhibit a 1:1 selectivity between the barrier layer and copper would be ideal for the barrier removal step of ECMP. The main goal of this research is to investigate the chemistries suitable for ECMP of copper and tantalum films. Copper was electroplated onto the gold electrode of quartz crystals, and its dissolution/passivation behavior in hydroxylamine solutions was studied at different applied potential values. The dissolution rate of copper is pH dependent and exhibits a maximum in the vicinity of pH 6. Copper dissolution increases with respect to overpotential (eta) and dissolution rates as high as 6000 A/min have been obtained at overpotential of 750mV. While both benzotriazole (BTA) and salicylhydroxamic acid (SHA) serve as good inhibitors at lower overpotentials, their effectiveness decreases at higher overpotentials. A fundamental study was undertaken to evaluate the usefulness of a sulfonic acid based chemical system for the removal of tantalum under ECMP conditions. Tantalum as well as copper samples were polished at low pressures (

  2. Tantalum-Tungsten Oxide Thermite Composite Prepared by Sol-Gel Synthesis and Spark Plasma Sintering

    Energy Technology Data Exchange (ETDEWEB)

    Cervantes, O; Kuntz, J; Gash, A; Munir, Z

    2009-02-13

    Energetic composite powders consisting of sol-gel derived nanostructured tungsten oxide were produced with various amounts of micrometer-scale tantalum fuel metal. Such energetic composite powders were ignition tested and results show that the powders are not sensitive to friction, spark and/or impact ignition. Initial consolidation experiments, using the High Pressure Spark Plasma Sintering (HPSPS) technique, on the sol-gel derived nanostructured tungsten oxide produced samples with higher relative density than can be achieved with commercially available tungsten oxide. The sol-gel derived nanostructured tungsten oxide with immobilized tantalum fuel metal (Ta - WO{sub 3}) energetic composite was consolidated to a density of 9.17 g.cm{sup -3} or 93% relative density. In addition those parts were consolidated without significant pre-reaction of the constituents, thus the sample retained its stored chemical energy.

  3. Superconducting properties in tantalum decorated three-dimensional graphene and carbon structures

    Energy Technology Data Exchange (ETDEWEB)

    Cobaleda, Cayetano S. F., E-mail: ccobaleda@usal.es, E-mail: wpan@sandia.gov [Sandia National Laboratories, P.O. Box 5800, MS 1086, Albuquerque, New Mexico 87185 (United States); Laboratorio de Bajas Temperaturas, Universidad de Salamanca, E-37008 Salamanca (Spain); Xiao, Xiaoyin; Burckel, D. Bruce; Polsky, Ronen; Pan, W., E-mail: ccobaleda@usal.es, E-mail: wpan@sandia.gov [Sandia National Laboratories, P.O. Box 5800, MS 1086, Albuquerque, New Mexico 87185 (United States); Huang, Duanni [Sandia National Laboratories, P.O. Box 5800, MS 1086, Albuquerque, New Mexico 87185 (United States); Department of Electrical and Computer Engineering, University of California, Santa Barbara, California 93106 (United States); Diez, Enrique [Laboratorio de Bajas Temperaturas, Universidad de Salamanca, E-37008 Salamanca (Spain)

    2014-08-04

    We present here the results on superconducting properties in tantalum thin films (100 nm thick) deposited on three-dimensional graphene (3DG) and carbon structures. A superconducting transition is observed in both composite thin films with a superconducting transition temperature of 1.2 K and 1.0 K, respectively. We have further measured the magnetoresistance at various temperatures and differential resistance dV/dI at different magnetic fields in these two composite thin films. In both samples, a much large critical magnetic field (∼2 T) is observed and this critical magnetic field shows linear temperature dependence. Finally, an anomalously large cooling effect was observed in the differential resistance measurements in our 3DG-tantalum device when the sample turns superconducting. Our results may have important implications in flexible superconducting electronic device applications.

  4. Development of advanced high strength tantalum base alloys. Part 2: Scale-up investigation

    Science.gov (United States)

    Ammon, R. L.; Buckman, R. W., Jr.

    1970-01-01

    Three experimental tantalum alloy compositions containing 14-16% W, 1% Re, 0.7% Hf, 0.025% C or 0.015% C and 0.015% N were prepared as two inch diameter ingots by consumable electrode vacuum arc melting. The as-cast ingots were processed by extrusion and swaging to one inch and 0.4 inch diameter rod and evaluated. Excellent high temperature forging behavior was exhibited by all three compositions. Creep strength at 2000 F to 2400 F was enhanced by higher tungsten additions as well as substitution of nitrogen for carbon. Weldability of all three compositions was determined to be adequate. Room temperature ductility was retained in the advanced tantalum alloy compositions as well as a notched/unnotched strength ratio of 1.4 for a notched bar having a K sub t = 2.9.

  5. Synthesis, Consolidation and Characterization of Sol-gel Derived Tantalum-Tungsten Oxide Thermite Composites

    Energy Technology Data Exchange (ETDEWEB)

    Cervantes, O [Univ. of California, Davis, CA (United States)

    2010-06-01

    Energetic composite powders consisting of sol-gel (SG) derived nanostructured tungsten oxide were produced with various amounts of micrometer-scale tantalum fuel metal. Such energetic composite powders were ignition-tested and results show that the powders are not sensitive to friction, spark and/or impact ignition. Initial consolidation experiments, using the High Pressure Spark Plasma Sintering (HPSPS) technique, on the SG derived nanostructured tungsten oxide produced samples with higher relative density than can be achieved with commercially available tungsten oxide. The SG derived nanostructured tungsten oxide with immobilized tantalum fuel metal (Ta - WO3) energetic composite was consolidated to a density of 9.17 g·cm-3 or 93% relative density. In addition, those samples were consolidated without significant pre-reaction of the constituents, thus retaining their stored chemical energy.

  6. Simulation of tantalum nanocrystals under shock-wave loading: Dislocations and twinning

    Science.gov (United States)

    Tramontina, D. R.; Hahn, E. N.; Meyers, M. A.; Bringa, E. M.

    2017-01-01

    We simulate strong shock waves in nanocrystalline tantalum using atomistic molecular dynamics simulations, for particle velocities in the range 0.35-2.0 km s-1, which induce pressures in the range 20-195 GPa. Our simulations explore strain rates in the range 108 s-1 - 1010 s-1, and lead to a peak strength in the range 3-15 GPa. Nanocrystalline tantalum exposed to strong shock waves demonstrates deformation enabled by concomitant dislocations, twinning, and grain boundary activity at a variety of particle velocities. Twinning is observed for a mean grain size of 7 nm, starting at around 32 GPa, in disagreement with models which predict a Hall-Petch behavior for twinning, i.e. a twinning stress scaling with grain size d as d-0.5, and supporting the presence of an inverse Hall-Petch effect for twinning at small grain sizes.

  7. Influence of the reactive atmosphere on the formation of nanoparticles in the plasma plume induced by nanosecond pulsed laser irradiation of metallic targets at atmospheric pressure and high repetition rate

    Science.gov (United States)

    Girault, M.; Le Garrec, J.-L.; Mitchell, J. B. A.; Jouvard, J.-M.; Carvou, E.; Menneveux, J.; Yu, J.; Ouf, F.-X.; Carles, S.; Potin, V.; Pillon, G.; Bourgeois, S.; Perez, J.; Marco de Lucas, M. C.; Lavisse, L.

    2016-06-01

    The influence of a reactive atmosphere on the formation of nanoparticles (NPs) in the plasma plume generated by nanosecond pulsed laser irradiation of metal targets (Ti, Al, Ag) was probed in situ using Small Angle X-ray Scattering (SAXS). Air and different O2-N2 gas mixtures were used as reactive gas within atmospheric pressure. SAXS results showed the formation of NPs in the plasma-plume with a mean radius varying in the 2-5 nm range. A decrease of the NPs size with increasing the O2 percentage in the O2-N2 gas mixture was also showed. Ex situ observations by transmission electron microscopy and structural characterizations by X-ray diffraction and Raman spectroscopy were also performed for powders collected in experiments done using air as ambient gas. The stability of the different metal oxides is discussed as being a key parameter influencing the formation of NPs in the plasma-plume.

  8. Separation of no-carrier-added {sup 203}Pb, a surrogate radioisotope, from proton irradiated {sup nat}Tl{sub 2}CO{sub 3} target using calcium alginate hydrogel beads

    Energy Technology Data Exchange (ETDEWEB)

    Sarkar, Kangkana; Sen, Kamalika [Univ. of Calcutta, Kolkata (India). Dept. of Chemistry; Lahiri, Susanta [Saha Institute of Nuclear Physics, Kolkata (India)

    2016-07-01

    {sup 203}Pb is a promising radioisotope in the field of medical science as an imaging surrogate of {sup 212}Pb. In the present investigation {sup 203}Pb was produced by proton irradiation of natural Tl{sub 2}CO{sub 3} target and was separated from the bulk Tl target using calcium alginate (CA) hydrogel beads with a high separation factor (3.8 x 10{sup 4} at 10{sup -3} M HNO{sub 3}). During the separation process {sup 203}Pb was encapsulated in CA beads and desorption of the radioisotope could only be achieved in 1M HNO{sub 3}. Possibility of Tl uptake was also checked in Fe doped CA (Fe-CA) beads after oxidation of Tl(I) to Tl(III) by sodium bismuthate. No significant uptake of Tl(III) was noticed in the Fe-CA beads. The matrix is therefore suitable for isolation of {sup 203}Pb from the target as well as its storage in the bead for therapeutic as well as diagnostic purpose.

  9. Niobium sputtered Havar foils for the high-power production of reactive [{sup 18}F]fluoride by proton irradiation of [{sup 18}O]H{sub 2}O targets

    Energy Technology Data Exchange (ETDEWEB)

    Wilson, J.S. [Edmonton PET Centre, Cross Cancer Institute, 11560 University Avenue, Edmonton, AB, T6G 1Z2 (Canada)], E-mail: johnwils@cancerboard.ab.ca; Avila-Rodriguez, M.A. [Edmonton PET Centre, Cross Cancer Institute, 11560 University Avenue, Edmonton, AB, T6G 1Z2 (Canada); Johnson, R.R.; Zyuzin, A. [Advanced Cyclotron Systems Inc., 7851 Alderbridge Way, Richmond, BC, V6X 2A4 (Canada); McQuarrie, S.A. [Edmonton PET Centre, Cross Cancer Institute, 11560 University Avenue, Edmonton, AB, T6G 1Z2 (Canada)

    2008-05-15

    Niobium sputtered Havar entrance foils were used for the production of reactive [{sup 18}F]fluoride by proton irradiation of [{sup 18}O]H{sub 2}O targets under pressurized conditions. The synthesis yield in the routine production of 2-[{sup 18}F]fluoro-2-deoxy-glucose (FDG) was used as an indicative parameter of the reactivity of {sup 18}F. The yield of FDG obtained with {sup 18}F produced in a target with Havar foil was used as a baseline. No statistically significant difference was found in the saturated yields of {sup 18}F when using Havar or Havar-Nb sputtered entrance foils. However, the amount of long-lived radionuclidic impurities decreased more than 10-fold using the Havar-Nb entrance foil. The average decay corrected synthesis yield of FDG, evaluated over a period of more than 2 years, was found to be {approx}5% higher when using a Havar-Nb entrance foil and a marked improvement on the FDG yield consistency was noted. In addition, the frequency of target rebuilding was greatly diminished when using the Nb sputtered entrance foil.

  10. fs激光在靶背表面产生的质子束成丝%Filamented proton beams from the rear surface of target irradiated by fs laser

    Institute of Scientific and Technical Information of China (English)

    谷渝秋; 蔡达锋; 郑志坚; 温天舒; 淳于书泰; 陈家斌; 周维民; 焦春晔; 陈豪

    2004-01-01

    介绍了利用3TW/60fs钛宝石超短超强激光与20μm铜薄膜靶相互作用的实验.实验观测到质子束的角分布随激光功率密度有所变化.在较高的功率密度(~1×1018W/cm2)时,观测到环状的质子束分布,发散角较大.在较低的激光功率密度(~2×1017W/cm2)时,质子束发散角减小,质子束出现成丝现象.质子束的角分布实际上反映了从靶前输运到靶背的超热电子电流横向分布.在输运过程中,由于Weibel不稳定性会使超热电子电流出现空心化并最后破裂成丝.%Proton emission patterns from the rear surface of targets irradiated by 60fs laser pulse at different intensity have been studied. The filaments of protons emission from 20μm Cu target were observed in the shots with lower laser intensity (about 2×1017W/cm2). As the laser intensity increased up to about 1×1018W/cm2 for the same target thickness, the filaments of proton beam disappeared and a hollow proton beam emerged. The patterns of proton beams revealed the traverse distribution of hot electrons reached the rear surface of target after a long distance transportation from the front surface of target. In this process, Weibel instability will drive electron beam into hollow structure and break into filaments in the end.

  11. On-line separation of refractory hafnium and tantalum isotopes at the ISOCELE separator

    CERN Document Server

    Liang, C F; Obert, J; Paris, P; Putaux, J C

    1981-01-01

    By chemical evaporation technique, neutron deficient hafnium nuclei have been on-line separated at the ISOCELE facility, from the isobar rare-earth elements, in the metal-fluoride HfF/sub 3//sup +/ ion form. Half-lives of /sup 162-165/Hf have been measured. Similarly, tantalum has been selectively separated on the TaF/sub 4//sup +/ form. (4 refs) .

  12. Powder metallurgical processing and metal purity: A case for capacitor grade sintered tantalum

    Indian Academy of Sciences (India)

    G S Upadhyaya

    2005-07-01

    The paper reviews the role of sintered tantalum as volumetric efficient electrical capacitor. Powder characteristics and sintering aspects are discussed. The role of impurities in influencing the electrical properties has been described. Today’s driving force behind the Ta market is the use of surface mounted versions known as chip types, for applications requiring a wide range of operational temperature, such as automotive electronics.

  13. Simultaneous determination of trace niobium, tantalum and tungsten in ferrous and non-ferrous alloys.

    Science.gov (United States)

    Vassilaros, G L; Byrnes, C J

    1976-03-01

    A method is presented for the determination of niobium, tantalum and tungsten in steel and non-ferrous alloys, based on hydrolysis with sulphurous acid followed by X-ray fluorescence measurements. The limit of determination is about 0.002% and the standard deviation is 0.002 at the 0.05% level. Results below 0.01% by this method are only semiquantitative.

  14. Mechanism of instability of carbides in Fe-TaC alloy under high energy electron irradiation at 673 K

    Science.gov (United States)

    Abe, Hiroaki; Ishizaki, Takahiro; Kano, Sho; Li, Feng; Satoh, Yuhki; Tanigawa, Hiroyasu; Hamaguchi, Dai; Nagase, Takeshi; Yasuda, Hidehiro

    2014-12-01

    Reduced activation ferritic/martensitic steels (RAFMs), such as F82H steel, are designed to enhance the high-temperature strength by formation of MX-type nanometer-scale precipitates, mainly TaC. However, their instability under irradiation was recently reported. The purpose of this work, therefore, is to clarify the mechanism employing simultaneous observations under electron irradiation at elevated temperature in a high voltage electron microscope. In this work, Fe-0.2 wt.% TaC was fabricated as a model alloy of F82H steel. The instability of the precipitates was observed under electron irradiation at 1 MeV or above. The remarkable shrinkage and disappearance were clearly observed under irradiation with 1.5 MeV and above. On the contrary, the precipitates were mostly stable below 0.75 MeV. Two kinds of mechanism of the irradiation-induced instability were deduced from the electron-energy dependence. One is the dissolution and diffusion of tantalum from precipitates in ferrite matrix. The other is the displacements of tantalum in precipitates that introduce dissolution of Ta into matrix.

  15. FY 2013 Summary Report: Post-Irradiation Examination of Zircaloy-4 Samples in Target Capsules and Initiation of Bending Fatigue Testing for Used Nuclear Fuel Vibration Integrity Investigations

    Energy Technology Data Exchange (ETDEWEB)

    Howard, Richard H [ORNL; Yan, Yong [ORNL; Wang, Jy-An John [ORNL; Ott, Larry J [ORNL; Howard, Rob L [ORNL

    2013-10-01

    This report documents ongoing work performed at Oak Ridge National Laboratory (ORNL) for the Department of Energy, Office of Fuel Cycle Technology Used Fuel Disposition Campaign (UFDC), and satisfies the deliverable for milestone M2FT-13OR0805041, “Data Report on Hydrogen Doping and Irradiation in HFIR.” This work is conducted under WBS 1.02.08.05, Work Package FT-13OR080504 ST “Storage and Transportation-Experiments – ORNL.” The objectives of work packages that make up the S&T Experiments Control Account are to conduct the separate effects tests (SET) and small-scale tests that have been identified in the Used Nuclear Fuel Storage and Transportation Data Gap Prioritization (FCRD-USED-2012-000109). In FY 2013, the R&D focused on cladding and container issues and small-scale tests as identified in Sections A-2.9 and A-2.12 of the prioritization report.

  16. Degradation of a tantalum filament during the hot-wire CVD of silicon nitride thin films

    Energy Technology Data Exchange (ETDEWEB)

    Oliphant, C.J. [Department of Physics, University of the Western Cape, Private Bag X17, Bellville 7535 (South Africa); National Metrology Institute of South Africa, Private Bag X34, Lynwood Ridge, Pretoria 0040 (South Africa); Arendse, C.J., E-mail: cjarendse@uwc.ac.za [Department of Physics, University of the Western Cape, Private Bag X17, Bellville 7535 (South Africa); Muller, T.F.G. [Department of Physics, University of the Western Cape, Private Bag X17, Bellville 7535 (South Africa); Jordaan, W.A. [National Metrology Institute of South Africa, Private Bag X34, Lynwood Ridge, Pretoria 0040 (South Africa); Knoesen, D. [Department of Physics, University of the Western Cape, Private Bag X17, Bellville 7535 (South Africa)

    2015-01-30

    Electron backscatter diffraction revealed that during the hot-wire deposition of silicon nitride, a tantalum filament partially transformed to some of its nitrides and silicides. The deposition of an encapsulating silicon nitride layer occurred at the cooler filament ends. Time-of-flight secondary ion mass spectroscopy disclosed the presence of hydrogen, nitrogen and silicon containing ions within the aged filament bulk. Hardness measurements revealed that the recrystallized tantalum core experienced significant hardening, whereas the silicides and nitrides were harder but more brittle. Crack growth, porosity and the different thermal expansion amongst the various phases are all enhanced at the hotter centre regions, which resulted in failure at these areas. - Highlights: • Tantalum filament degrades and fails during hot-wire CVD of silicon nitride thin films. • An encapsulating silicon nitride layer is deposited at the cooler ends. • Electron backscatter diffraction reveals Ta-silicides and -nitrides with a Ta core. • Filament failure occurs at hot centre regions due to different mechanical properties of Ta, its silicides and nitrides.

  17. Status of Post Irradiation Examination of FCAB and FCAT Irradiation Capsules

    Energy Technology Data Exchange (ETDEWEB)

    Field, Kevin G. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Fuel Cycle Research and Development (FCRD); Yamamoto, Yukinori [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Fuel Cycle Research and Development (FCRD); Howard, Richard H. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Fuel Cycle Research and Development (FCRD)

    2016-09-29

    A series of irradiation programs are ongoing to address the need for determining the radiation tolerance of FeCrAl alloys. These irradiation programs, deemed the FCAT and FCAB irradiation programs, use the High Flux Isotope Reactor (HFIR) to irradiate second generation wrought FeCrAl alloys and early-generation powder-metallurgy (PM) oxide dispersion-strengthened (ODS) FeCrAl alloys. Irradiations have been or are being performed at temperatures of 200°C, 330°C, and 550°C from doses of 1.8 dpa up to 16 dpa. Preliminary post-irradiation examination (PIE) on low dose (<2 dpa) irradiation capsules of tensile specimens has been performed. Analysis of co-irradiated SiC thermometry have shown reasonable matching between the nominal irradiation temperatures and the target irradiation temperatures. Room temperature tensile tests have shown typical radiation-induced hardening and embrittlement at irradiations of 200°C and 330°C, but a propensity for softening when irradiated to 550°C for the wrought alloys. The PM-ODS FeCrAl specimens showed less hardening compared to the wrought alloys. Future PIE includes high temperature tensile tests on the low dose irradiation capsules as well as the determination of reference fracture toughness transition temperature, To, in alloys irradiated to 7 dpa and higher.

  18. Status of Post Irradiation Examination of FCAB and FCAT Irradiation Capsules

    Energy Technology Data Exchange (ETDEWEB)

    Field, Kevin G. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Fuel Cycle Research and Development (FCRD); Yamamoto, Yukinori [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Fuel Cycle Research and Development (FCRD); Howard, Richard H. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Fuel Cycle Research and Development (FCRD)

    2016-09-29

    A series of irradiation programs are ongoing to address the need for determining the radiation tolerance of FeCrAl alloys. These irradiation programs, deemed the FCAT and FCAB irradiation programs, use the High Flux Isotope Reactor (HFIR) to irradiate second generation wrought FeCrAl alloys and early generation powder-metallurgy (PM) oxide dispersion strengthened (ODS) FeCrAl alloys. Irradiations have been or are being performed at temperatures of 200°C, 330°C, and 550°C from doses of 1.8 dpa up to 16 dpa. Preliminary post-irradiation examination (PIE) on low dose (<2 dpa) irradiation capsules of tensile specimens has been performed. Analysis of co-irradiated SiC thermometry have shown reasonable matching between the nominal irradiation temperatures and the target irradiation temperatures. Room temperature tensile tests have shown typical radiation-induced hardening and embrittlement at irradiations of 200°C and 330°C but a propensity for softening when irradiated to 550°C for the wrought alloys. The PM-ODS FeCrAl specimens showed less hardening compared to the wrought alloys. Future PIE includes high temperature tensile tests on the low dose irradiation capsules as well as the determination of reference fracture toughness transition temperature, To, in alloys irradiated to 7 dpa and higher.

  19. Conflict minerals from the Democratic Republic of the Congo: global tantalum processing plants, a critical part of the tantalum supply chain

    Science.gov (United States)

    Papp, John F.

    2014-01-01

    The U.S. Geological Survey (USGS) analyzes mineral and metal supply chains to identify and describe major components of mineral and metal material flows from ore extraction, through intermediate forms, to a final product. Supply chain analyses may be used (1) to identify risks to the United States associated with the supply of critical and strategic minerals and metals and (2) to provide greater supply chain transparency so that policymakers have the fact-based information needed to formulate public policy. This fact sheet focuses on the post-mining/pre-consumer-product part of the tantalum supply chain. The USGS National Minerals Information Center (NMIC) has been asked by governmental and non-governmental organizations to provide information about tantalum, tin, tungsten, and gold (collectively known as “3TG minerals”) processing facilities worldwide in response to U.S. legislation aimed at identifying and removing the supply chain links between the trade in these minerals and civil unrest in the Democratic Republic of the Congo and adjacent countries.

  20. Proton irradiation of simple gas mixtures: Influence of irradiation parameters

    Science.gov (United States)

    Sack, Norbert J.; Schuster, R.; Hofmann, A.

    1990-01-01

    In order to get information about the influence of irradiation parameters on radiolysis processes of astrophysical interest, methane gas targets were irradiated with 6.5 MeV protons at a pressure of 1 bar and room temperature. Yields of higher hydrocarbons like ethane or propane were found by analysis of irradiated gas samples using gas chromatography. The handling of the proton beam was of great experimental importance for determining the irradiation parameters. In a series of experiments current density of the proton beam and total absorbed energy were shown to have a large influence on the yields of produced hydrocarbons. Mechanistic interpretations of the results are given and conclusions are drawn with regard to the chemistry and the simulation of various astrophysical systems.

  1. Study of Rayleigh–Taylor growth in laser irradiated planar SiO{sub 2} targets at ignition-relevant conditions

    Energy Technology Data Exchange (ETDEWEB)

    Hager, J. D.; Collins, T. J. B.; Knauer, J. P.; Meyerhofer, D. D.; Sangster, T. C. [Laboratory for Laser Energetics, University of Rochester, 250 East River Road, Rochester, New York 14623-1299 (United States); Smalyuk, V. A. [Lawrence Livermore National Laboratory, Livermore, California 94550 (United States)

    2013-07-15

    Rayleigh–Taylor (RT) growth experiments were performed on the OMEGA laser [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)] using planar SiO{sub 2} targets seeded with a single mode 60-μm wavelength perturbation driven at peak laser intensities up to 9 × 10{sup 14} W/cm{sup 2}. These are the first RT measurements in SiO{sub 2} at conditions relevant to direct-drive inertial confinement fusion ignition. The measured average modulation growth rates agree with the 2-D hydrodynamics code DRACO, providing an important step in the development of target ablators that are robust to RT growth and hot- electron preheat considerations when driven at the intensities required to achieve thermonuclear ignition.

  2. Synthesis of surface molecular imprinted TiO2/graphene photocatalyst and its highly efficient photocatalytic degradation of target pollutant under visible light irradiation

    Science.gov (United States)

    Lai, Cui; Wang, Man-Man; Zeng, Guang-Ming; Liu, Yun-Guo; Huang, Dan-Lian; Zhang, Chen; Wang, Rong-Zhong; Xu, Piao; Cheng, Min; Huang, Chao; Wu, Hai-Peng; Qin, Lei

    2016-12-01

    The molecular imprinted TiO2/graphene photocatalyst (MIP-TiO2/GR) was successfully prepared with bisphenol A (BPA) as the template molecule (target pollutant) and o-phenylenediamine (OPDA) as functional monomers by the surface molecular imprinting method. The combination between BPA and OPDA led to the formation of the precursor, and the subsequent polymerization of OPDA initiated by ultraviolet radiation can ensure the realization of MIP-TiO2/GR. The samples were characterized by SEM, EDS, XRD, BET, UV-vis DRS and Zeta potential. In addition, adsorption capacities, adsorption selectivity and visible light photocatalytic performances of MIP-TiO2/GR and non-imprinted TiO2/graphene (NIP-TiO2/GR) were evaluated. Moreover, the effects of pH and initial BPA concentration on removal efficiency of BPA were also investigated. The results showed that MIP-TiO2/GR exhibited better adsorption capacity and adsorption selectivity towards the template molecule compared to NIP-TiO2/GR due to the imprinted cavities on the surface of MIP-TiO2/GR. Moreover, the photocatalytic activity of MIP-TiO2/GR toward the target molecules was stronger than that of NIP-TiO2/GR as a result of large adsorption capacity to target molecules and narrow band gap energy on MIP-TiO2/GR. Therefore, modifying the photocatalyst by the surface molecular imprinting is a promising method to improve the molecule recognition and photocatalytic efficiency of photocatalyst for target pollutant.

  3. Phytosanitary irradiation - Development and application

    Science.gov (United States)

    Hallman, Guy J.; Loaharanu, Paisan

    2016-12-01

    Phytosanitary irradiation, the use of ionizing radiation to disinfest traded agricultural commodities of regulated pests, is a growing use of food irradiation that has great continued potential for increase in commercial application. In 2015 approximately 25,000 t of fresh fruits and vegetables were irradiated globally for phytosanitary purposes. Phytosanitary irradiation has resulted in a paradigm shift in phytosanitation in that the final burden of proof of efficacy of the treatment has shifted from no live pests upon inspection at a port of entry (as for all previous phytosanitary treatments) to total dependence on certification that the treatment for target pests is based on adequate science and is commercially conducted and protected from post-treatment infestation. In this regard phytosanitary irradiation is managed more like a hazard analysis and critical control point (HACCP) approach more consistent with food safety than phytosanitation. Thus, phytosanitary irradiation offers a more complete and rigorous methodology for safeguarding than other phytosanitary measures. The role of different organizations in achieving commercial application of phytosanitary irradiation is discussed as well as future issues and applications, including new generic doses.

  4. Spectroscopic study of the electrochemical behaviour of tantalum(V) chloride and oxochloride species in 1-butyl-1-methylpyrrolidinium chloride

    Energy Technology Data Exchange (ETDEWEB)

    Babushkina, Olga B., E-mail: olga.babushkina@cest.a [Centre in Electrochemical Surface Technology (CEST), Viktor Kaplan street 2, A-2700, Wiener Neustadt (Austria); Ekres, Silvia [Centre in Electrochemical Surface Technology (CEST), Viktor Kaplan street 2, A-2700, Wiener Neustadt (Austria)

    2010-12-30

    FTIR spectroscopy was used to identify the oxochloride species of tantalum(V) in ionic liquids and to confirm the correlations between their presence in electrolytes and the changes in the route of electrochemical reduction of tantalum(V). Electrochemical behaviour of the mixtures (x)1-butyl-1-methyl-pyrrolidinium chloride-(1 - x)TaCl{sub 5} at x = 0.80, 0.65, and 0.40 was investigated over the temperature range 90-160 {sup o}C with respect to the electrochemical deposition of tantalum and was discussed in terms of spectroscopic data. The mechanism of electrochemical reduction of tantalum(V) in the basic and acidic electrolytes depends strongly on the structure and composition of the electro active species of tantalum(V) defined by the molar composition of ionic liquids and on the competition between tantalum(V) chloride and oxochloride species. In the basic mixture at x = 0.80, with octahedral [TaCl{sub 6}]{sup -} ions as the electrochemically active species only the first reduction step Ta{sup 5+} {yields} Ta{sup 4+} at -0.31 V was observed. The competitive reduction of tantalum(V) oxochloride species occurs at more anodic potential (-0.01 V) than the reduction of the chloride complexes and can restrict the further reduction of tantalum(IV). In the basic ionic liquid at x = 0.65, the cyclic voltammograms exhibit reduction peaks at -0.31 V and -0.51 V attributed to the diffusion controlled process as [TaCl{sub 6}]{sup -} + e{sup -} {yields} [TaCl{sub 6}]{sup 2-} and [TaCl{sub 6}]{sup 2-} + e{sup -} {yields} [TaCl{sub 6}]{sup 3-}. The further irreversible reduction of tantalum(III) to metallic state may occur at -2.1 V. In the acidic ionic liquids, at x = 0.40 the electrochemical reduction of two species occurs, TaCl{sub 6}{sup -} and Ta{sub 2}Cl{sub 11}{sup -} and it is limited by two electron transfer for both of them at -0.3 V and -1.5 V, respectively.

  5. Investigation of Space and Energy Distributions of Neutrons Generated in Lead Target and Uranium Blanket of the Electronuclear System "Energy plus Transmutation" under Irradiation with Protons at 1.5 GeV

    CERN Document Server

    Zhuk, I V; Krivopustov, M I; Sosnin, A N; Chultem, D; Vestmaer, V; Tumendelger, T; Zaveryukha, O S; Pavlyuk, A B

    2002-01-01

    The work contains the results of space-energy distributions of neutrons in U/Pb assembly, consisting of extended lead target and the model of natural uranium blanket irradiated with relativistic protons at 1.5 GeV. The research is carried out in the framework of a series of experiments using the model of subcritical heterogeneous electronuclear system at the Laboratory of High Energies, JINR, Dubna ("Investigation of Physical Aspects of Electronuclear Method of Energy Production and Transmutation of Radioactive Waste Using Beams from JINR Synchrophasotron/Nuclotron" - project "Energy plus Transmutation"). The results of measurements and calculations of ^{235}U, ^{238}U and ^{232}Th fission rate distributions as well as threshold spectral indexes {\\bar\\sigma_f^{^{232}Th}}/{\\bar\\sigma_f^{^{235}U}} and {\\bar\\sigma_f^{^{238}U}}/{\\bar\\sigma_f^{^{235}U}} along the radius of the target and model uranium blanket are presented. The results of measurements and calculations of ^{234}U, ^{236}U and ^{237}Np fission rate ...

  6. Monte Carlo calculated microdosimetric spread for cell nucleus-sized targets exposed to brachytherapy 125I and 192Ir sources and 60Co cell irradiation.

    Science.gov (United States)

    Villegas, Fernanda; Tilly, Nina; Ahnesjö, Anders

    2013-09-07

    The stochastic nature of ionizing radiation interactions causes a microdosimetric spread in energy depositions for cell or cell nucleus-sized volumes. The magnitude of the spread may be a confounding factor in dose response analysis. The aim of this work is to give values for the microdosimetric spread for a range of doses imparted by (125)I and (192)Ir brachytherapy radionuclides, and for a (60)Co source. An upgraded version of the Monte Carlo code PENELOPE was used to obtain frequency distributions of specific energy for each of these radiation qualities and for four different cell nucleus-sized volumes. The results demonstrate that the magnitude of the microdosimetric spread increases when the target size decreases or when the energy of the radiation quality is reduced. Frequency distributions calculated according to the formalism of Kellerer and Chmelevsky using full convolution of the Monte Carlo calculated single track frequency distributions confirm that at doses exceeding 0.08 Gy for (125)I, 0.1 Gy for (192)Ir, and 0.2 Gy for (60)Co, the resulting distribution can be accurately approximated with a normal distribution. A parameterization of the width of the distribution as a function of dose and target volume of interest is presented as a convenient form for the use in response modelling or similar contexts.

  7. Novel hierarchical tantalum oxide-PDMS hybrid coating for medical implants: One pot synthesis, characterization and modulation of fibroblast proliferation.

    Science.gov (United States)

    Tran, Phong A; Fox, Kate; Tran, Nhiem

    2017-01-01

    Surface properties such as morphology, roughness and charge density have a strong influence on the interaction of biomaterials and cells. Hierarchical materials with a combination of micron/submicron and nanoscale features for coating of medical implants could therefore have significant potential to modulate cellular responses and eventually improve the performance of the implants. In this study, we report a simple, one pot wet chemistry preparation of a hybrid coating system with hierarchical surface structures consisting of polydimethylsiloxane (PDMS) and tantalum oxide. Medical grade, amine functional PDMS was mixed with tantalum ethoxide which subsequently formed Ta2O5in situ through hydrolysis and condensation during coating process. The coatings were characterized by SEM, EDS, XPS, confocal scanning microscopy, contact angle measurement and in vitro cell culture. Varying PDMS and tantalum ethoxide ratios resulted in coatings of different surface textures ranging from smooth to submicro- and nano-structured. Strikingly, hierarchical surfaces containing both microscale (1-1.5μm) and nanoscale (86-163nm) particles were found on coatings synthesized with 20% and 40% (v/v) tantalum ethoxide. The coatings were similar in term of hydrophobicity but showed different surface roughness and chemical composition. Importantly, higher cell proliferation was observed on hybrid surface with hierarchical structures compared to pure PDMS or pure tantalum oxide. The coating process is simple, versatile, carried out under ambient condition and requires no special equipment.

  8. Test of a High Power Target Design

    CERN Multimedia

    2002-01-01

    %IS343 :\\\\ \\\\ A high power tantalum disc-foil target (RIST) has been developed for the proposed radioactive beam facility, SIRIUS, at the Rutherford Appleton Laboratory. The yield and release characteristics of the RIST target design have been measured at ISOLDE. The results indicate that the yields are at least as good as the best ISOLDE roll-foil targets and that the release curves are significantly faster in most cases. Both targets use 20 -25 $\\mu$m thick foils, but in a different internal geometry.\\\\ \\\\Investigations have continued at ISOLDE with targets having different foil thickness and internal geometries in an attempt to understand the release mechanisms and in particular to maximise the yield of short lived isotopes. A theoretical model has been developed which fits the release curves and gives physical values of the diffusion constants.\\\\ \\\\The latest target is constructed from 2 $\\mu$m thick tantalum foils (mass only 10 mg) and shows very short release times. The yield of $^{11}$Li (half-life of ...

  9. Mechanical properties of tantalum-tungsten interlayer between tungsten tile and thimble to prevent helium leak from He-cooled divertor

    Science.gov (United States)

    Zhang, Pingping; Shen, Weiping; Zhou, Yanan; Zhang, Qingling

    2013-03-01

    The tungsten parts made of pure tungsten tile and dispersion strengthened tungsten thimble with 3 mm interlayer of tantalum-tungsten alloy are fabricated by Spark Plasmas Sintering (SPS). The process of SPS is that the temperature is raised to 1700 °C at a rate of 100 °C/min and kept for 3 min, under a constant pressure of 50MPa along the Z-axis. The mechanical properties of the interlayer with different percent of tantalum are measured. The results show that with increasing percent of tantalum, the hardness first increases and then decreases; and as the indentation on the sample is closer to dispersion strengthened tungsten, the value of Vickers hardness is much higher. The Vickers hardness of interlayer is the highest when the content of tantalum is 50% and the indentation is next to dispersion strengthened tungsten. Bending strength drops with increasing content of tantalum, when the content of tantalum is 100% the value of bending strength is the lowest. The fracture toughness is highest as the content of tantalum is 25%, the value is 9.89MPa•m1/2. The toughening tungsten-tantalum interlayer between tungsten tile and thimble would better prevent helium leak from He-cooled divertor for DEMO.

  10. Growth of tantalum pentoxide film by pulsed laser deposition

    Science.gov (United States)

    Zhang, Jun-Ying; Fang, Qi; Boyd, Ian W.

    1999-01-01

    Thin films of Ta 2O 5 have been deposited on quartz and silicon substrates by 532-nm (Nd:YAG) pulsed laser deposition (PLD) in various O 2 gas environments. The influence of the deposition parameters, such as oxygen pressure, substrate temperature and annealing under UV irradiation using a 172-nm excimer lamp, on the properties of the grown films, has been studied. The refractive index of the films increases with increasing pressure of O 2. X-ray diffraction measurements show that the as-deposited films are amorphous at temperatures below 500°C and possess orthorhombic (β-Ta 2O 5) crystal structure at temperatures above 600°C. The optical properties determined by UV spectrophotometry also strongly depend on the deposition parameters. At O 2 pressures above 0.15 mbar, the refractive index of the films was about 2.12 which is close to the bulk Ta 2O 5 value of 2.2. Optical transmittance around 85% in the visible region of the spectrum was obtained at an oxygen pressure of 0.2 mbar.

  11. Gas generation during waste treatment of acidic solutions from the dissolution of irradiated LEU targets for 99Mo production

    Energy Technology Data Exchange (ETDEWEB)

    Bakel, Allen J. [Argonne National Lab. (ANL), Argonne, IL (United States); Conner, Cliff [Argonne National Lab. (ANL), Argonne, IL (United States); Quigley, Kevin [Argonne National Lab. (ANL), Argonne, IL (United States); Vandegrift, George F. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2017-01-01

    The goal of the Reduced Enrichment for Research and Test Reactors Program is to limit the use of high-enriched uranium (HEU) in research and test reactors by substituting low-enriched uranium (LEU) wherever possible. The work reported here documents our work to develop the calcining technologies and processes that will be needed for 99Mo production using LEU foil targets and the Modified Cintichem Process. The primary concern with the conversion to LEU from HEU targets is that it would result in a five- to six-fold increase in the total uranium. This increase results in more liquid waste from the process. We have been working to minimize the increase in liquid waste and to minimize the impact of any change in liquid waste. Direct calcination of uranium-rich nitric acid solutions generates NO2 gas and UO3 solid. We have proposed two processes for treating the liquid waste from a Modified Cintichem Process with a LEU foil. One is an optimized direct calcination process that is similar to the process currently in use. The other is a uranyl oxalate precipitation process. The specific goal of the work reported here was to characterize and compare the chemical reactions that occur during these two processes. In particular, the amounts and compositions of the gaseous and solid products were of interest. A series of experiments was carried out to show the effects of temperature and the redox potential of the reaction atmosphere. The primary products of the direct calcination process were mixtures of U3O8 and UO3 solids and NO2 gas. The primary products of the oxalate precipitation process were mixtures of U3O8 and UO2 solid and CO2 gas. Higher temperature and a reducing atmosphere tended to favor quadrivalent over hexavalent uranium in the solid product. These data will help producers to decide between the two processes. In addition, the data can be used to design

  12. Tantalum acetabular augments in one-stage exchange of infected total hip arthroplasty: a case-control study.

    Science.gov (United States)

    Klatte, Till Orla; Kendoff, Daniel; Sabihi, Reza; Kamath, Atul F; Rueger, Johannes M; Gehrke, Thorsten

    2014-07-01

    During the one-stage exchange procedure for periprosthetic joint infection (PJI) after total hip arthroplasty (THA), acetabular defects challenge reconstructive options. Porous tantalum augments are an established tool for addressing acetabular destruction in aseptic cases, but their utility in septic exchange is unknown. This retrospective case-control study presents the initial results of tantalum augmentation during one-stage exchange for PJI. Primary endpoints were rates of re-infection and short-term complications associated with this technique. Study patients had no higher risk of re-infection with equivalent durability at early follow-up with a re-infection rate in both groups of 4%. In conclusion, tantalum augments are a viable option for addressing acetabular defects in one-stage exchange for septic THA. Further study is necessary to assess long-term durability when compared to traditional techniques for acetabular reconstruction.

  13. Porous tantalum uncemented acetabular shells in revision total hip replacement: two to four year clinical and radiographic results.

    Science.gov (United States)

    Kim, W Y; Greidanus, N V; Duncan, C P; Masri, B A; Garbuz, D S

    2008-01-01

    In cementless revision total hip arthroplasty (THA), achieving initial implant stability and maximising host bone contact is key to the success of reconstruction. Porous tantalum acetabular shells may represent an improvement from conventional porous coated uncemented cups in revision acetabular reconstruction associated with severe acetabular bone defects. We reviewed the results of 46 acetabular revisions with Paprosky 2 and 3 acetabular bone defects done with a hemispheric, tantalum acetabular shell and multiple supplementary screws. At a mean follow-up of 40 (24-51) months, one acetabular shell had been revised in a patient with a Paprosky 3B defect. Cementless acetabular revision with the tantalum acetabular shell demonstrated excellent early clinical and radiographic results and warrants further evaluation in revision acetabular reconstruction associated with severe acetabular bone defects.

  14. The effect of tantalum and carbon on the structure/properties of a single crystal nickel-base superalloy. M.S. Thesis. Final Report

    Science.gov (United States)

    Nguyen, H. C.

    1984-01-01

    The microstructure, phase chemistry, and creep and hot tensile properties were studied as a function of tantalum and carbon levels in Mar-M247 type single crystal alloys. Microstructural studies showed that several types of carbides (MC, M23C6 and M5C) are present in the normal carbon (0.10 wt % C) alloys after heat treatment. In general, the composition of the MC carbides changes from titanium rich to tantalum rich as the tantalum level in the alloy increases. Small M23C6 carbides are present in all alloys. Tungsten rich M6C carbides are also observed in the alloy containing no tantalum. No carbides are present in the low carbon (0.01 wt % C) alloy series. The morphology of gamma prime is observed to be sensitive to heat treatment and tantalum level in the alloy. Cuboidal gamma prime is present in all the as cast structures. After heat treatment, the gamma prime precipitates tend to have a more spheroidal like morphology, and this tendency increases as the tantalum level decreases. On prolonged aging, the gamma prime reverts back to a cuboidal morphology or under stress at high temperatures, forms a rafted structure. The weight fraction and lattice parameter of the spheroidal gamma prime increases with increasing tantalum content. Changes in the phase chemistry of the gamma prime matrix and gamma prime have also been analyzed using phase extraction techniques. The partitioning ratio decreases for tungsten and aluminum and increases for tantalum as the tantalum content increases for both alloy series; no significant changes occur in the partitioning ratios of the other alloying elements. A reduction in secondary creep rate and an increase in rupture time result from increasing the tantalum content and decreasing the carbon level.

  15. Tantalum nitride for photocatalytic water splitting: concept and applications

    KAUST Repository

    Nurlaela, Ela

    2016-10-12

    Along with many other solar energy conversion processes, research on photocatalytic water splitting to generate hydrogen and oxygen has experienced rapid major development over the past years. Developing an efficient visible-light-responsive photocatalyst has been one of the targets of such research efforts. In this regard, nitride materials, particularly Ta3N5, have been the subject of investigation due to their promising properties. This review focuses on the fundamental parameters involved in the photocatalytic processes targeting overall water splitting using Ta3N5 as a model photocatalyst. The discussion primarily focuses on relevant parameters that are involved in photon absorption, exciton separation, carrier diffusion, carrier transport, catalytic efficiency, and mass transfer of the reactants. An overview of collaborative experimental and theoretical approaches to achieve efficient photocatalytic water splitting using Ta3N5 is discussed.

  16. Generation of a quasi-monoenergetic high energy proton beam from a vacuum-sandwiched double layer target irradiated by an ultraintense laser pulse

    Energy Technology Data Exchange (ETDEWEB)

    Nam Kim, Kyung; Lee, Kitae, E-mail: klee@kaeri.re.kr; Hee Park, Seong; Young Lee, Ji; Uk Jeong, Young; Vinokurov, Nikolay [Center for Quantum-Beam-based Radiation Research, Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Gi Kim, Yong [Department of Physics, Kongju National University, Kongju (Korea, Republic of)

    2014-04-15

    An acceleration mechanism to generate a high energy proton beam with a narrow energy spread in the laser-induced plasma acceleration of a proton beam is proposed; this mechanism employs two thin foils separated by a narrow vacuum gap. Instead of a thin sheath field at the plasma surfaces, it utilizes an electrostatic field formed in the bulk of the plasma. From a one-dimensional fluid analysis, it has been found that with an appropriate target thickness, protons on the front surface of the second layer can be fed into the plasma, in which the protons are accelerated by an electrostatic field built into the bulk of the plasma. This leads to a proton beam with higher energy and a narrower energy spread than those accelerated at the rear surface of the second layer. The acceleration mechanism is also verified by a two-dimensional particle-in-cell simulation. With a 27-fs long and 2×10{sup 19} W/cm{sup 2} intense laser pulse, a proton beam with an 18-MeV peak energy and a 35% energy spread is generated. The peak energy is higher than that from the rear surface of the second layer by a factor of 3.

  17. Au-Pt alloy nanoparticles obtained by nanosecond laser irradiation of gold and platinum bulk targets in an ethylene glycol solution

    Science.gov (United States)

    Moniri, Samira; Reza Hantehzadeh, Mohammad; Ghoranneviss, Mahmood; Asadi Asadabad, Mohsen

    2017-07-01

    Au-Pt alloy nanoparticles (NPs) of different compositions ( Au0Pt100 , Au30Pt70 , Au50Pt50 , Au70Pt30 , and Au100Pt0 were obtained using the nanosecond laser ablation of gold and platinum bulk targets in ethylene glycol, followed by mixing highly monodisperse Au and Pt nanocolloids, for the first time. UV-vis absorption spectra of NPs showed that by increasing the Au content in the Au-Pt NPs, the surface plasmon resonance (SPR) peak red-shifted, from 260 to 573nm in a nonlinear way. In addition, the mean crystalline size, crystal structure, d-spacing, and lattice parameters of NPs were estimated from the XRD spectra. Microscopy studies revealed the most NPs have a spherical or near-spherical shape, and the average sizes of Au0Pt100 , Au30Pt70 , Au50Pt50 , Au70Pt30 , and Au100Pt0 NPs were calculated to be 12.50, 14.15, 18.53, 19.29, and 26.38nm, respectively. Also, the chemical identity of the molecules adhering to the NPs surface was considered by Raman and FT-IR spectroscopy techniques. Among different synthesis methods, the demonstrated technique allows easy synthesis of alloy NPs in aqueous media at room temperature with no formation of by-products.

  18. Measurement of the High Energy Neutron Flux on the Surface of the Natural Uranium Target Assembly QUINTA Irradiated by Deuterons of 4 and 8 GeV Energy

    Science.gov (United States)

    Adam, J.; Baldin, A. A.; Chilap, V.; Furman, W.; Katovsky, K.; Khushvaktov, J.; Kumar, V.; Pronskikh, V.; Mar'in, I.; Solnyshkin, A.; Suchopar, M.; Tsupko-Sitnikov, V.; Tyutyunnikov, S.; Vrzalova, J.; Wagner, V.; Zavorka, L.

    Experiments with the natural uranium target assembly "QUINTA" exposed to 4 and 8 GeV deuteron beams of the Nuclotron accelerator at the Joint Institute for Nuclear Research (Dubna) are analyzed. The reaction rates of 27Al(n,y1)24Na, 27Al(n,y2)22Na and 27Al(n,y3)7Be reactions with effective threshold energies of 5, 27, and 119 MeV were measured at both 4 GeV and 8 GeV deuteron beam energies. The average neutron fluxes between the effective threshold energies and the effective ends of the neutron spectra (which are 800 or 1000 MeV for 4 or 8 GeV deuterons) were determined. The evidence for the intensity shift of the neutron spectra to higher neutron energies with the increase of the deuteron energy from 4 GeV to 8 GeV was found from the ratios of the average neutron fluxes. The reaction rates and the average neutron fluxes were calculated with the MCNPX 2.7 code.

  19. Electrostatic self-assembly of multilayer copolymeric membranes on the surface of porous tantalum implants for sustained release of doxorubicin

    Directory of Open Access Journals (Sweden)

    Guo X

    2011-11-01

    Full Text Available Xinming Guo1,*, Muwan Chen1,2,*, Wenzhou Feng1,*, Jiabi Liang1, Huibin Zhao1, Lin Tian1, Hui Chao3, Xuenong Zou11Orthopaedic Research institute/Department of Orthopaedic Surgery, the First Affiliated Hospital and Department of Pharmacy, the Fifth Affiliated Hospital, Sun Yat-sen University, Guangzhou, People's Republic of China; 2Interdisciplinary Nanoscience Center (iNANO, Aarhus University, Denmark; 3Ministry of Education Key Laboratory of Bioinorganic and Synthetic Chemistry, School of Chemistry and Chemical Engineering of Sun Yat-sen University, Guangzhou, People's Republic of China *The first three authors contributed equally to this work as co-first authorAbstract: Many studies in recent years have focused on surface engineering of implant materials in order to improve their biocompatibility and other performance. Porous tantalum implants have increasingly been used in implant surgeries, due to their biocompatibility, physical stability, and good mechanical strength. In this study we functionalized the porous tantalum implant for sustained drug delivery capability via electrostatic self-assembly of polyelectrolytes of hyaluronic acid, methylated collagen, and terpolymer on the surface of a porous tantalum implant. The anticancer drug doxorubicin was encapsulated into the multilayer copolymer membranes on the porous tantalum implants. Results showed the sustained released of doxorubicin from the functionalized porous tantalum implants for up to 1 month. The drug release solutions in 1 month all had inhibitory effects on the proliferation of chondrosarcoma cell line SW1353. These results suggest that this functionalized implant could be used in reconstructive surgery for the treatment of bone tumor as a local, sustained drug delivery system.Keywords: self-assembly, surface modification, tantalum, drug delivery system, doxorubicin, bone tumor

  20. XPS and GDOES Characterization of Porous Coating Enriched with Copper and Calcium Obtained on Tantalum via Plasma Electrolytic Oxidation

    Directory of Open Access Journals (Sweden)

    Krzysztof Rokosz

    2016-01-01

    Full Text Available XPS and GDOES characterizations of porous coatings on tantalum after Plasma Electrolytic Oxidation (PEO at 450 V for 3 minutes in electrolyte containing concentrated (85% phosphoric acid with calcium nitrate and copper (II nitrate are described. Based on the obtained data, it may be concluded that the PEO coating consists of tantalum (Ta5+, calcium (Ca2+, copper (Cu2+  and Cu+, and phosphates (PO43-. It has to be pointed out that copper and calcium are distributed throughout the volume. The authors also propose a new model of PEO, based on the derivative of GDOES signals with sputtering time.

  1. Use of a Tantalum Liner to Reduce Bore Erosion and Increase Muzzle Velocity in Two-Stage Light Gas Guns

    Science.gov (United States)

    Bogdanoff, David W.

    2015-01-01

    Muzzle velocities and gun erosion predicted by earlier numerical simulations of two stage light gas guns with steel gun tubes were in good agreement with experimental values. In a subsequent study, simulations of high performance shots were repeated with rhenium (Re) gun tubes. Large increases in muzzle velocity (2 - 4 km/sec) were predicted for Re tubes. In addition, the hydrogen-produced gun tube erosion was, in general, predicted to be zero with Re tubes. Tantalum (Ta) has some mechanical properties superior to those of Re. Tantalum has a lower modulus of elasticity than Re for better force transmission from the refractory metal liner to an underlying thick wall steel tube. Tantalum also has greater ductility than Re for better survivability during severe stress/strain cycles. Also, tantalum has been used as a coating or liner in military powder guns with encouraging results. Tantalum has, however, somewhat inferior thermal properties to those of rhenium, with a lower melting point and lower density and thermal conductivity. The present study was undertaken to see to what degree the muzzle velocity gains of rhenium gun tubes (over steel tubes) could be achieved with tantalum gun tubes. Nine high performance shots were modeled with a new version of our CFD gun code for steel, rhenium and tantalum gun tubes. For all except the highest velocity shot, the results with Ta tubes were nearly identical with those for Re tubes. Even for the highest velocity shot, the muzzle velocity gain over a steel tube using Ta was 82% of the gain obtained using Re. Thus, the somewhat inferior thermal properties of Ta (when compared to those of Re) translate into only very slightly poorer overall muzzle velocity performance. When this fact is combined with the superior mechanical properties of Ta and the encouraging performance of Ta liners/coatings in military powder guns, tantalum is to be preferred over Re as a liner/coating material for two stage light gas guns to increase muzzle

  2. Quasi-static Tensile and Compressive Behavior of Nanocrystalline Tantalum Based on Miniature Specimen Testing—Part II: Mechanical Properties

    Science.gov (United States)

    Ligda, J.; D'Antuono, D. Scotto; Taheri, M. L.; Schuster, B. E.; Wei, Q.

    2016-11-01

    In Part I of this work (this issue), we presented the microstructure of tantalum processed by high-pressure torsion (HPT). In this part, we will present results based on site-specific micro-mechanical testing. The experimental techniques were used due to the intrinsic microstructure gradient associated with HPT processing. The primary objective is to explore the grain size effect on the quasi-static mechanical properties of HPT processed tantalum with ultrafine grained (UFG, grain size d 100 nm) and nanocrystalline (NC, d body-centered cubic metals with UFG/NC microstructure tend to have localized shear band even under quasi-static uniaxial compression.

  3. Development of high temperature materials for solid propellant rocket nozzle applications. [tantalum carbides-tungsten fiber composites

    Science.gov (United States)

    Manning, C. R., Jr.; Honeycutt, L., III

    1974-01-01

    Evaluation of tantalum carbide-tungsten fiber composites has been completed as far as weight percent carbon additions and weight percent additions of tungsten fiber. Extensive studies were undertaken concerning Young's Modulus and fracture strength of this material. Also, in-depth analysis of the embrittling effects of the extra carbon additions on the tungsten fibers has been completed. The complete fabrication procedure for the tantalum carbide-tungsten fiber composites with extra carbon additions is given. Microprobe and metallographic studies showed the effect of extra carbon on the tungsten fibers, and evaluation of the thermal shock parameter fracture strength/Young's Modulus is included.

  4. Experimental lumbar spine fusion with novel tantalum-coated carbon fiber implant.

    Science.gov (United States)

    Li, Haisheng; Zou, Xuenong; Woo, Charlotte; Ding, Ming; Lind, Martin; Bünger, Cody

    2007-04-01

    Implants of carbon fiber composite have been widely used in orthopedic and spinal surgeries. However, studies using carbon fiber-reinforced cages demonstrate frequent appearance of fibrous layer interposed between the implant and the surrounding bone. The aim of the present study was to test the possibility of coating a biocompatible metal layer on top of the carbon fiber material, to improve its biological performance. Tantalum was chosen because of its bone compatibility, based on our previous studies. A novel spinal fusion cage was fabricated by applying a thin tantalum coating on the surface of carbon-carbon composite material through chemical vapor deposition. Mechanical and biological performance was tested in vitro and in vivo. Compress strength was found to be 4.9 kN (SD, 0.2). Fatigue test with 500,000 cycles was passed. In vitro radiological evaluation demonstrated good compatibility with X-ray and CT scan examinations. In vivo test employed eight pigs weighing 50 kg each. Instrumented lumbar spine fusion of L3/4 and L4/5 with these cages was performed on each pig. After 3 months, excellent bone integration property was demonstrated by direct contact of the cage with the host bone and newly formed bone. No inflammatory cells were found around the implant. Cages packed with two different graft materials (autograft and COLLOSS) achieved the same new bone formation. The present study proved that coating tantalum on top of the carbon-based implant is feasible, and good bone integration could be achieved.

  5. Synthesis of tantalum carbide and nitride nanoparticles using a reactive mesoporous template for electrochemical hydrogen evolution

    KAUST Repository

    Alhajri, Nawal Saad

    2013-01-01

    Tantalum carbide and nitride nanocrystals were prepared through the reaction of a tantalum precursor with mesoporous graphitic (mpg)-C 3N4. The effects of the reaction temperature, the ratio of the Ta precursor to the reactive template (mpg-C3N4), and the selection of the carrier gas (Ar, N2 and NH3) on the resultant crystal phases and structures were investigated. The produced samples were characterized using powder X-ray diffraction (XRD), CHN elemental analyses, thermogravimetric analyses (TGA), nitrogen sorption, a temperature-programmed reaction with mass spectroscopy (MS), X-ray photoelectron spectroscopy (XPS), and transmission electron microscopy (TEM). The results indicate that the different tantalum phases with cubic structure, TaN, Ta2CN, and TaC, can be formed under a flow of nitrogen when formed at different temperatures. The Ta3N5 phase with a Ta5+ oxidation state was solely obtained at 1023 K under a flow of ammonia, which gasified the C 3N4 template and was confirmed by detecting the decomposed gaseous products via MS. Significantly, the formation of TaC, Ta2CN, and TaN can be controlled by altering the weight ratio of the C 3N4 template relative to the Ta precursor at 1573 K under a flow of nitrogen. The high C3N4/Ta precursor ratio generally resulted in high carbide content rather than a nitride one, consistent with the role of mpg-C3N4 as a carbon source. Electrochemical measurements revealed that the synthesized nanomaterials were consistently able to produce hydrogen under acidic conditions (pH 1). The obtained Tafel slope indicates that the rate-determining step is the Volmer discharge step, which is consistent with adsorbed hydrogen being weakly bound to the surface during electrocatalysis. © 2013 The Royal Society of Chemistry.

  6. Tantalum augments for Paprosky IIIA defects remain stable at midterm followup.

    Science.gov (United States)

    Del Gaizo, Daniel J; Kancherla, Vamsi; Sporer, Scott M; Paprosky, Wayne G

    2012-02-01

    Initial reports with short-term followup of porous tantalum acetabular components and augments for Paprosky IIIA acetabular defects demonstrate high hip scores, low rates of aseptic loosening, and low rates of complications. However, longer-term followup with a larger cohort is needed to determine the durability of these reconstructions. We therefore determined the functional scores, rates of aseptic loosening, and complications in patients with Paprosky IIIA acetabular defects treated with porous tantalum acetabular components and augments. We retrospectively reviewed 37 acetabular revisions in 36 patients (one patient with bilateral revisions) treated with a porous tantalum acetabular component and augment. All patients had defects classified as Type IIIa using the system of Paprosky et al. Harris hip scores were obtained and radiographic examination was performed before surgery and through most recent followup. The minimum followup was 26 months (mean, 60 months; range, 26-106 months). One patient developed aseptic loosening of the acetabular reconstruction requiring revision; seven other patients required further surgery for periprosthetic femoral fracture (two), acute infection (three), and recurrent dislocation (two). Thirty-five of 37 hips had no or occasional pain at final followup. Mean Harris hip scores improved from 33.0 preoperatively (range, 12.6-58.7) to 81.5 postoperatively (range, 27.0-99.8). Although the complication rate requiring further surgery was considerable, most patients with these reconstructions had pain relief and reasonable function with low rates of loosening at midterm followup. Level IV, therapeutic study. See Guidelines for Authors for a complete description of levels of evidence.

  7. The effect of tantalum on the structure/properties of two polycrystalline nickel-base superalloys: B-1900 + Hf MAR-M247. M.S. Thesis, Final Report

    Science.gov (United States)

    Janowski, G. M.

    1985-01-01

    The microstructure, phase compositions, and phase fractions were studied in conventionally cast B-1900 + Hf and both conventionally cast and directionally solidified MAR-M247 as a function of tantalum concentration. The hot tensile and creep rupture properties of the solutionized and aged MAR-M247-type alloys were also determined as a function of tantalum level. The effects of tantalum on the microstructure and phase compositions of B-1900 + Hf and MAR-M247 (conventionally cast and directionally solidified) were found to be very similar. The addition of tantalum to the as cast and heat treated alloys was shown to cause the partial replacement of the Hf in the MC carbides by Ta, although the degree of replacement was decreased by the solutionizing and aging heat treatment. The gamma prime and minor phase fractions (primarily MC type carbides) both increased approximately linearly with tantalum concentration. The gamma prime phase compositions were relatively insensitive to tantalum variations with the exception of the tantalum and/or hafnium levels. Bulk tantalum additions increased the tantalum, chromium, and cobalt levels of the gamma phase in both alloy series. The increase in the concentrations of the latter two elements in the gamma phase was a result of the decrease in the gamma phase fraction with increasing bulk tantalum concentration and constant gamma/gamma prime partitioning ratio. Tantalum additions increased the yield stress and ultimate tensile strength of the directionally solidified MAR-M247 type alloys and had no significant effect on ductility.

  8. Effects of pressure and temperature on the yield strength of tantalum and rhenium

    Science.gov (United States)

    Crow, Joseph Allan

    The effects of pressure and temperature on the yield strength of tantalum and the effects of pressure on the yield strength of rhenium were investigated using ruby fluorescence. A new Raman system with a motorized stage and near diffraction limit was built to map 2-dimensionally, the pressures inside of a diamond anvil cell. The 2-dimensional data is used to create contour maps and surface plots of the pressures and calculate the pressure gradients induced in the samples. Using the Birch-Murnaghan equation of state, the final sample thickness, and the pressure gradients, the yield strength as a function of temperature and pressure are calculated.

  9. Effects of alloy composition in alleviating embrittlement problems associated with the tantalum alloy T-111

    Science.gov (United States)

    Stephens, J. R.

    1975-01-01

    The causes of aging embrittlement in T-111 (Ta-8W-2Hf) and the effect of alloy modification were investigated. Results show that T-111 possesses a critical combination of tungsten and hafnium that leads to loss in ductility at -196 C after aging near 1040 C. It was found that this occurs because tungsten enhances hafnium segregation to grain boundaries, which also leads to increased susceptibility to hydrogen embrittlement. Aging embrittlement was not observed in tantalum alloys with reduced tungsten or hafnium contents; most of the alloys studied have lower strengths than T-111 and exhibit susceptibility to hydrogen embrittlement.

  10. Leakage Current Degradation Due to Ion Drift and Diffusion in Tantalum and Niobium Oxide Capacitors

    Directory of Open Access Journals (Sweden)

    Kuparowitz Martin

    2017-06-01

    Full Text Available High temperature and high electric field applications in tantalum and niobium capacitors are limited by the mechanism of ion migration and field crystallization in a tantalum or niobium pentoxide insulating layer. The study of leakage current (DCL variation in time as a result of increasing temperature and electric field might provide information about the physical mechanism of degradation. The experiments were performed on tantalum and niobium oxide capacitors at temperatures of about 125°C and applied voltages ranging up to rated voltages of 35 V and 16 V for tantalum and niobium oxide capacitors, respectively. Homogeneous distribution of oxygen vacancies acting as positive ions within the pentoxide layer was assumed before the experiments. DCL vs. time characteristics at a fixed temperature have several phases. At the beginning of ageing the DCL increases exponentially with time. In this period ions in the insulating layer are being moved in the electric field by drift only. Due to that the concentration of ions near the cathode increases producing a positively charged region near the cathode. The electric field near the cathode increases and the potential barrier between the cathode and insulating layer decreases which results in increasing DCL. However, redistribution of positive ions in the insulator layer leads to creation of a ion concentration gradient which results in a gradual increase of the ion diffusion current in the direction opposite to the ion drift current component. The equilibrium between the two for a given temperature and electric field results in saturation of the leakage current value. DCL vs. time characteristics are described by the exponential stretched law. We found that during the initial part of ageing an exponent n = 1 applies. That corresponds to the ion drift motion only. After long-time application of the electric field at a high temperature the DCL vs. time characteristics are described by the exponential

  11. Tantalum oxide nanoscale resistive switching devices: TEM/EELS study (Presentation Recording)

    Science.gov (United States)

    Norris, Kate J.; Zhang, Jiaming; Merced-Grafals, Emmanuelle; Musunuru, Srinitya; Zhang, Max; Samuels, Katy; Yang, Jianhua J.; Kobayashi, Nobuhiko P.

    2015-08-01

    The field of non-volatile memory devices has been boosted by resistive switching, a reversible change in electrical resistance of a dielectric layer through the application of a voltage potential. Tantalum oxide being one of the leading candidates for the dielectric component of resistance switching devices was investigated in this study. 55nm TaOx devices in all states were compared through cross sectional TEM techniques including HRTEM, EELS, and EFTEM and will be discussed in this presentation. Based on the chemical and physical features found in the cross sectioned nanodevices we will discuss the switching mechanism of these nanoscale devices.

  12. Molecular functionalization of tantalum oxide surface towards development of apatite growth

    Science.gov (United States)

    Aubry, D.; Volcke, C.; Arnould, Ch.; Humbert, C.; Thiry, P. A.; Delhalle, J.; Mekhalif, Z.

    2009-02-01

    We have studied the apatite growth dynamics on tantalum oxide surfaces. This nucleation is obtained via an organosilane intermediate layer between the apatite and the substrate surface. Four organosilane layers (differing by their terminal functionality) were investigated. Their characterization with atomic force microscopy and other techniques such as X-ray photoelectron spectroscopy (XPS) and wetting measurements highlighted the influence of the organosilane terminal groups on the apatite growth rates. Results revealed that apatite is indeed growing faster on phosphate terminal groups than on the three other groups studied (vinyl, hydroxyl and carboxyl).

  13. Experimental investigation of resonance self-shielding and the Doppler effect in uranium and tantalum

    Science.gov (United States)

    Byoun, T. Y.; Block, R. C.; Semler, T. T.

    1972-01-01

    A series of average transmission and average self-indication ratio measurements were performed in order to investigate the temperature dependence of the resonance self-shielding effect in the unresolved resonance region of depleted uranium and tantalum. The measurements were carried out at 77 K, 295 K and approximately 1000 K with sample thicknesses varying from approximately 0.1 to 1.0 mean free path. The average resonance parameters as well as the temperature dependence were determined by using an analytical model which directly integrates over the resonance parameter distribution functions.

  14. Molecular functionalization of tantalum oxide surface towards development of apatite growth

    Energy Technology Data Exchange (ETDEWEB)

    Aubry, D. [Laboratory of Chemistry and Electrochemistry of Surfaces (CES), University of Namur, FUNDP, Rue de Bruxelles 61, B-5000 Namur (Belgium); Volcke, C. [Research Center in Physics of Matter and Radiation (PMR), University of Namur, FUNDP, Rue de Bruxelles 61, B-5000 Namur (Belgium); Arnould, Ch. [Laboratory of Chemistry and Electrochemistry of Surfaces (CES), University of Namur, FUNDP, Rue de Bruxelles 61, B-5000 Namur (Belgium); Humbert, C.; Thiry, P.A. [Research Center in Physics of Matter and Radiation (PMR), University of Namur, FUNDP, Rue de Bruxelles 61, B-5000 Namur (Belgium); Delhalle, J. [Laboratory of Chemistry and Electrochemistry of Surfaces (CES), University of Namur, FUNDP, Rue de Bruxelles 61, B-5000 Namur (Belgium); Mekhalif, Z., E-mail: zineb.mekhalif@fundp.ac.be [Laboratory of Chemistry and Electrochemistry of Surfaces (CES), University of Namur, FUNDP, Rue de Bruxelles 61, B-5000 Namur (Belgium)

    2009-02-15

    We have studied the apatite growth dynamics on tantalum oxide surfaces. This nucleation is obtained via an organosilane intermediate layer between the apatite and the substrate surface. Four organosilane layers (differing by their terminal functionality) were investigated. Their characterization with atomic force microscopy and other techniques such as X-ray photoelectron spectroscopy (XPS) and wetting measurements highlighted the influence of the organosilane terminal groups on the apatite growth rates. Results revealed that apatite is indeed growing faster on phosphate terminal groups than on the three other groups studied (vinyl, hydroxyl and carboxyl).

  15. Tantalum films with well-controlled roughness grown by oblique incidence deposition

    Science.gov (United States)

    Rechendorff, K.; Hovgaard, M. B.; Chevallier, J.; Foss, M.; Besenbacher, F.

    2005-08-01

    We have investigated how tantalum films with well-controlled surface roughness can be grown by e-gun evaporation with oblique angle of incidence between the evaporation flux and the surface normal. Due to a more pronounced shadowing effect the root-mean-square roughness increases from about 2 to 33 nm as grazing incidence is approached. The exponent, characterizing the scaling of the root-mean-square roughness with length scale (α), varies from 0.75 to 0.93, and a clear correlation is found between the angle of incidence and root-mean-square roughness.

  16. Scalable standard optical sources in the VUV: Emissions from electron impact on metals. [tantalum and tungsten

    Science.gov (United States)

    Hughes, R.

    1980-01-01

    The use of electron impact on metals in the development of a compact optical standard lamp in the vacuum ultraviolet is described. Two different mechanisms are exploited, transition radiation and bremsstrahlung. Transition radiation will be used as a primary standard from 1200A to 3000A using 10 keV electron impact on tungsten. Bremsstrahlung will be used in the soft X-ray region below 1200A to less than 5A as an optical transfer standard from 4 keV electron impact on tantalum or tungsten.

  17. Improving intra-fractional target position accuracy using a 3D surface surrogate for left breast irradiation using the respiratory-gated deep-inspiration breath-hold technique.

    Directory of Open Access Journals (Sweden)

    Yi Rong

    Full Text Available PURPOSE: To evaluate the use of 3D optical surface imaging as a surrogate for respiratory gated deep-inspiration breath-hold (DIBH for left breast irradiation. MATERIAL AND METHODS: Patients with left-sided breast cancer treated with lumpectomy or mastectomy were selected as candidates for DIBH treatment for their external beam radiation therapy. Treatment plans were created on both free breathing (FB and DIBH computed tomography (CT simulation scans to determine dosimetric benefits from DIBH. The Real-time Position Management (RPM system was used to acquire patient's breathing trace during DIBH CT acquisition and treatment delivery. The reference 3D surface models from FB and DIBH CT scans were generated and transferred to the "AlignRT" system for patient positioning and real-time treatment monitoring. MV Cine images were acquired during treatment for each beam as quality assurance for intra-fractional position verification. The chest wall excursions measured on these images were used to define the actual target position during treatment, and to investigate the accuracy and reproducibility of RPM and AlignRT. RESULTS: Reduction in heart dose can be achieved using DIBH for left breast/chest wall radiation. RPM was shown to have inferior correlation with the actual target position, as determined by the MV Cine imaging. Therefore, RPM alone may not be an adequate surrogate in defining the breath-hold level. Alternatively, the AlignRT surface imaging demonstrated a superior correlation with the actual target positioning during DIBH. Both the vertical and magnitude real-time deltas (RTDs reported by AlignRT can be used as the gating parameter, with a recommended threshold of ±3 mm and 5 mm, respectively. CONCLUSION: The RPM system alone may not be sufficient for the required level of accuracy in left-sided breast/CW DIBH treatments. The 3D surface imaging can be used to ensure patient setup and monitor inter- and intra- fractional motions

  18. History and prospects of the application of porous tantalum in arthrodesis%多孔钽在关节融合中的历史与前景

    Institute of Scientific and Technical Information of China (English)

    赵阳; 李亮; 王志强

    2014-01-01

    Objective To review the characteristics of metal porous tantalum and its application in arthrodesis. Methods Recent literatures concerning the characteristics of porous tantalum and its application in arthrodesis were retrieved from China National Knowledge Internet ( CNKI ) and PubMed databases. Results Porous tantalum was a kind of metal with low elastic modulus, whose appearance was similar to that of cancellous bone. Recently, it had been widely applied in the orthopaedic ifeld, inluding hip replacement and knee replacement, spine surgery, bone graft substitutes and arthrodesis. Porous tantalum could be attached by a great quantity of bones and soft tissues quickly, with a high volumetric porosity of 70%-80%, good mechanical characteristics, biocompatibility and biological activity and excellent growth characteristics of bone and soft tissues. At present, satisfactory outcomes could be achieved in the clinical application of porous tantalum for hip and knee injuries. Furthermore, with the development of medicine, porous tantalum could be applied in the treatment of other joint injuries. Conclusions Good mechanical stability and early surgical outcomes can be obtained by porous tantalum material in arthrodesis.

  19. Studying tantalum-based high-κ dielectrics in terms of capacitance measurements

    Science.gov (United States)

    Stojanovska-Georgievska, L.

    2016-08-01

    The trend of rapid development of microelectronics towards nano-miniaturization dictates the inevitable introduction of dielectrics with high permittivity (high-κ dielectrics), as alternative material for replacing SiO2. Therefore, studying these materials in terms of their characteristics, especially in terms of reliability, is of great importance for proper design and manufacture of devices. In this paper, alteration of capacitance in different frequency regimes is used, in order to determine the overall behavior of the material. Samples investigated here are MOS structures containing nanoscale tantalum based dielectrics. Layers of pure Ta2O5, but also Hf and Ti doped tantalum pentoxide, i.e. Ta2O5:Hf and Ta2O5:Ti are studied here. All samples are considered as ultrathin oxide layers with thicknesses less than 15 nm, obtained by radio frequent sputtering on p-type silicon substrate. Measuring capacitive characteristics enables determination of several specific parameters of the structures. The obtained results for capacitance in accumulation, the thickness and time evolution of the interfacial SiO2 layer, values of flatband and threshold voltage, density of oxide charges, interfacial and border states, and reliability properties favor the possibilities for more intensive use of studied materials in new nanoelectronic technologies.

  20. Electronic properties of tantalum pentoxide polymorphs from first-principles calculations

    Energy Technology Data Exchange (ETDEWEB)

    Lee, J. [Department of Materials Science and Engineering, University of Michigan, Ann Arbor 48109 (United States); Department of Electrical Engineering and Computer Science, University of Michigan, Ann Arbor 48109 (United States); Lu, W. [Department of Electrical Engineering and Computer Science, University of Michigan, Ann Arbor 48109 (United States); Kioupakis, E., E-mail: kioup@umich.edu [Department of Materials Science and Engineering, University of Michigan, Ann Arbor 48109 (United States)

    2014-11-17

    Tantalum pentoxide (Ta{sub 2}O{sub 5}) is extensively studied for its attractive properties in dielectric films, anti-reflection coatings, and resistive switching memory. Although various crystalline structures of tantalum pentoxide have been reported, its structural, electronic, and optical properties still remain a subject of research. We investigate the electronic and optical properties of crystalline and amorphous Ta{sub 2}O{sub 5} structures using first-principles calculations based on density functional theory and the GW method. The calculated band gaps of the crystalline structures are too small to explain the experimental measurements, but the amorphous structure exhibits a strong exciton binding energy and an optical band gap (∼4 eV) in agreement with experiment. We determine the atomic orbitals that constitute the conduction band for each polymorph and analyze the dependence of the band gap on the atomic geometry. Our results establish the connection between the underlying structure and the electronic and optical properties of Ta{sub 2}O{sub 5}.

  1. Thermal Conductivity of Saturated Liquid Toluene by Use of Anodized Tantalum Hot Wires at High Temperatures.

    Science.gov (United States)

    Perkins, R A; Ramires, M L; Nieto de Castro, C A

    2000-01-01

    Absolute measurements of the thermal conductivity of a distilled and dried sample of toluene near saturation are reported. The transient hot-wire technique with an anodized tantalum hot wire was used. The thermal conductivities were measured at temperatures from 300 K to 550 K at different applied power levels to assess the uncertainty with which it is possible to measure liquid thermal conductivity over wide temperature ranges with an anodized tantalum wire. The wire resistance versus temperature was monitored throughout the measurements to study the stability of the wire calibration. The relative expanded uncertainty of the resulting data at the level of 2 standard deviations (coverage factor k = 2) is 0.5 % up to 480 K and 1.5 % between 480 K and 550 K, and is limited by drift in the wire calibration at temperatures above 450 K. Significant thermal-radiation effects are observed at the highest temperatures. The radiation-corrected results agree well with data from transient hot-wire measurements with bare platinum hot wires as well as with data derived from thermal diffusivities obtained using light-scattering techniques.

  2. Antibacterial properties and cytocompatibility of tantalum oxide coatings with different silver content

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Heng-Li [School of Dentistry, China Medical University, Taichung 404, Taiwan (China); Chang, Yin-Yu, E-mail: yinyu@mail2000.com.tw; Chen, Hung-Jui; Chou, Yu-Kai [Department of Mechanical and Computer-Aided Engineering, National Formosa University, Yunlin 632, Taiwan (China); Lai, Chih-Ho [School of Medicine, China Medical University, Taichung 404, Taiwan (China); Chen, Michael Y. C. [Division of Oral and Maxillofacial Surgery, China Medical University Hospital, Taichung 404, Taiwan (China)

    2014-03-15

    Tantalum (Ta) oxides and their coatings have been proved to increase their applications in the biomedical fields by improving osseointegration and wear resistance. In this study, Ta oxide coatings containing different proportions of Ag are deposited on SS304 materials. A twin-gun magnetron sputtering system is used to deposit the tantalum oxide-Ag coating. In this study, Staphylococcus aureus, which exhibits physiological commensalism on the human skin, nares, and mucosal and oral areas, is chosen as the model for in vitro antibacterial analyses via a fluorescence staining method using Syto9. The cytocompatibility and adhesive morphology of human skin fibroblast cells (CCD-966SK) on the coatings are also determined by using the microculture tetrazolium assay. This study shows that Ta{sub 2}O{sub 5} and Ta{sub 2}O{sub 5}-Ag coatings with 12.5 at. % of Ag exhibit improved antibacterial effects against S. aureus and have good skin fibroblast cell cellular biocompatibility.

  3. Sheet resistance of alumina ceramic after high energy implantation of tantalum ions

    Energy Technology Data Exchange (ETDEWEB)

    Savkin, Konstantin P., E-mail: savkinkp@mail2000.ru [Institute of High Current Electronics SB RAS, 2/3 Akademichesky Avenue, 634055 Tomsk (Russian Federation); Bugaev, Alexey S., E-mail: bugaev@opee.hcei.tsc.ru [Institute of High Current Electronics SB RAS, 2/3 Akademichesky Avenue, 634055 Tomsk (Russian Federation); Nikolaev, Alexey G., E-mail: nik@opee.hcei.tsc.ru [Institute of High Current Electronics SB RAS, 2/3 Akademichesky Avenue, 634055 Tomsk (Russian Federation); Oks, Efim M., E-mail: oks@opee.hcei.tsc.ru [Institute of High Current Electronics SB RAS, 2/3 Akademichesky Avenue, 634055 Tomsk (Russian Federation); Shandrikov, Maxim V., E-mail: shandrikov@opee.hcei.tsc.ru [Institute of High Current Electronics SB RAS, 2/3 Akademichesky Avenue, 634055 Tomsk (Russian Federation); Yushkov, Georgy Yu., E-mail: gyushkov@mail.ru [Institute of High Current Electronics SB RAS, 2/3 Akademichesky Avenue, 634055 Tomsk (Russian Federation); Tyunkov, Andrey V., E-mail: tyunkov@opee.hcei.tsc.ru [Tomsk State University of Control Systems and Radioelectronics, 40 Lenin Avenue, 634050 Tomsk (Russian Federation); Savruk, Elena V., E-mail: savruk@mail.ru [Tomsk State University of Control Systems and Radioelectronics, 40 Lenin Avenue, 634050 Tomsk (Russian Federation)

    2014-08-15

    Highlights: • Tantalum ions with the average energy about 145 keV were implanted in the surfaces of flat polycrystalline alumina samples. • The sheet resistance of implanted ceramic reduced after implantation with increasing of the implanted dose. • Normalized surface conductivity of treated alumina ceramic reduced only on 1% during 200 days after finishing the implantation process. • Creation of weak conducting layer on the surface of the ceramic insulator electric field strength of the flashover increases more than 25%. - Abstract: The results of investigation of the sheet resistance of alumina ceramic as a function of the fluence of implanted metal ions are presented. Tantalum ions with the average energy about 145 keV were used in experiments. Estimation of the sheet resistance was performed from analysis of volt–ampere characteristics by measuring the leakage current at a voltage between 100 V and several kilovolts, which was applied at a small area of the implanted surface. Energy dispersive X-ray analysis was used to determine composition of elements in the surface of the implanted ceramics. As a practical application of research results, it was shown that, after the creation of a weak conducting layer on the surface of the ceramic insulator, the electric field strength of the flashover increases by more than 25%.

  4. Tantalum (oxy)nitrides: preparation, characterisation and enhancement of photo-Fenton-like degradation of atrazine under visible light.

    Science.gov (United States)

    Du, Yingxun; Zhao, Lu; Su, Yaling

    2011-11-15

    Tantalum (oxy)nitrides were prepared by the nitridation of Ta(2)O(5) and were added to a photo-Fenton-like system to enhance Fe(3+) reduction and atrazine degradation under visible light. The samples were characterized by XRD, XPS, DRS and BET analyses. XPS analysis showed that the nitrogen content of the tantalum (oxy)nitride samples increased noticeably with the nitridation temperature and nitridation time but slightly with the flow rate of NH(3). XRD results showed Ta(2)O(5) was first converted to TaON and then to Ta(3)N(5) when the nitridation temperature increased. DRS analysis showed that the sample obtained at 800°C displayed the strongest absorption of visible light. However, the ability of the tantalum (oxy)nitrides to reduce Fe(3+) did not increase continuously with the nitrogen content. Sample 7 (700°C, [Formula: see text] , 6h) showed the highest level of photocatalytic activity for Fe(3+) reduction. This is because the photocatalytic activity of TaON for Fe(3+) reduction is higher than that of Ta(3)N(5). And a slight synergetic effect was observed between TaON and Ta(3)N(5). With the addition of sample 7, H(2)O(2) decomposition and atrazine degradation were significantly accelerated in a photo-Fenton-like system under visible light. The regenerated tantalum (oxy)nitrides catalyst displayed considerably stable performance for atrazine degradation.

  5. Structure of the transition zone and its influence on the strength of copper-tantalum joint (Explosion welding)

    Science.gov (United States)

    Greenberg, B. A.; Ivanov, M. A.; Rybin, V. V.; Elkina, O. A.; Patselov, A. M.; Antonova, O. V.; Inozemtsev, A. V.; Salishchev, G. A.; Kozhevnikov, V. E.

    2012-10-01

    The joint of copper and tantalum, metals without mutual solubility, formed by explosion welding is studied. The mechanism of the influence of mutual solubility on the structure of the transition zone is established. It is demonstrated that the interface contains heterogeneities, and their role in the strength of the materials joint is revealed. A microheterogeneous structure of the joint zones is detected.

  6. Extension of the lifetime of tantalum filaments in the hot-wire (Cat) 3 Chemical Vapor Deposition process

    CSIR Research Space (South Africa)

    Knoesen, D

    2008-01-01

    Full Text Available One of the prime components of a hot-wire (Cat) Chemical Vapor Deposition system is the filament used to pyro-catalytically crack the gases like silane. Burnt out tantalum filaments were studied to determine the possible improvement of lifetime...

  7. Tantalum coating on TiO{sub 2} nanotubes induces superior rate of matrix mineralization and osteofunctionality in human osteoblasts

    Energy Technology Data Exchange (ETDEWEB)

    Frandsen, Christine J.; Brammer, Karla S. [Materials Science and Engineering, University of California at San Diego, La Jolla, CA 92093 (United States); Noh, Kunbae [Corporate Research Institute, Cheil Industries, Inc., Gocheon-Dong, Uiwang-Si, Gyeonggi-Do, 437-711 (Korea, Republic of); Johnston, Gary [Materials Science and Engineering, University of California at San Diego, La Jolla, CA 92093 (United States); Jin, Sungho, E-mail: jin@ucsd.edu [Materials Science and Engineering, University of California at San Diego, La Jolla, CA 92093 (United States); Mechanical and Aerospace Engineering, University of California at San Diego, La Jolla, CA 92093 (United States)

    2014-04-01

    Nanostructured surface geometries have been the focus of a multitude of recent biomaterial research, and exciting findings have been published. However, only a few publications have directly compared nanostructures of various surface chemistries. The work herein directly compares the response of human osteoblast cells to surfaces of identical nanotube geometries with two well-known orthopedic biomaterials: titanium oxide (TiO{sub 2}) and tantalum (Ta). The results reveal that the Ta surface chemistry on the nanotube architecture enhances alkaline phosphatase activity, and promotes a ∼ 30% faster rate of matrix mineralization and bone-nodule formation when compared to results on bare TiO{sub 2} nanotubes. This study implies that unique combinations of surface chemistry and nanostructure may influence cell behavior due to distinctive physico-chemical properties. These findings are of paramount importance to the orthopedics field for understanding cell behavior in response to subtle alterations in nanostructure and surface chemistry, and will enable further insight into the complex manipulation of biomaterial surfaces. With increased focus in the field of orthopedic materials research on nanostructured surfaces, this study emphasizes the need for careful and systematic review of variations in surface chemistry in concurrence with nanotopographical changes. - Highlights: • A TiO{sub 2} nanotube surface structure was coated with tantalum. • Osteoblast cell response was compared between the tantalum coated and as-formed TiO{sub 2} nanotube surface. • We observed superior rates of bone matrix mineralization and osteoblast maturation on the tantalum coated nanotube surface.

  8. Studies on the separation of {sup 89}Sr(II) from irradiated yttria target using 4, 4{sup '}(5{sup '}) di-tert-butyl-cyclohexano-18-crown-6 (DtBuCH18C6) by solvent extraction technique

    Energy Technology Data Exchange (ETDEWEB)

    Saha, Debasish; Vithya, Jayagopal; Kumar, Ramalingam; Venkata Subramani, Canchipuram Ramamoorthy; Vasudeva Rao, Polur Ranga [Indira Gandhi Centre for Atomic Research (IGCAR), Kalpakkam (India). Chemistry Group

    2016-07-01

    The radioisotope {sup 89}Sr as {sup 89}SrCl{sub 2} is medically useful for bone pain palliation and is produced in fast reactors using the {sup 89}Y(n, p){sup 89}Sr reaction. A procedure for isolation of the radionuclide {sup 89}Sr by chemical processing of the irradiated Y{sub 2}O{sub 3} target has been standardised and trial runs have been carried out at the Fast Breeder Test Reactor (FBTR), Kalpakkam. The chemical processing of the irradiated Y{sub 2}O{sub 3} target involves (i) the removal of target Y(III) by TBP extraction and (ii) further purification of the separated {sup 89}Sr fraction by cationic exchange chromatography. However a selective isolation of {sup 89}Sr by the Sr-specific crown ether makes the above chemical processing faster and relatively simple. This work presents a study on the selective removal of Sr from the irradiated target dissolver solution using the Sr-specific crown ether 4,4{sup '}(5{sup '}) di-tert-butyl-cyclohexano-18-crown-6 (DtBuCH18C6) in octanol medium. The separation behaviour of the other impurities such as Ce(IV), Y(III), Tb(III), Eu(III), Zn(II), Mn(II) and Rb(I) present along with Sr(II) in the irradiated sample was also investigated. The method of separation by using the crown ether DtBuCH18C6 is proved to be a potential tool for the purification of {sup 89}Sr(II) source produced from yttria target in fast reactors.

  9. Analyses of the factors for the demagnetization of permanent magnets caused by high-energy electron irradiation.

    Science.gov (United States)

    Asano, Yoshihiro; Bizen, Teruhiko; Maréchal, Xavier

    2009-05-01

    Demagnetization owing to high-energy electron irradiation has been analyzed for permanent magnets used in insertion devices of synchrotron radiation sources, using the Monte Carlo code FLUKA. The experimental data of a thermally treated Nd(2)Fe(14)B permanent magnet with a copper or a tantalum block at electron energies ranging from 2 to 8 GeV were compared with the calculation data of the absorbed doses, photoneutron production distributions and star densities. The results indicate that low-energy photoneutrons and bremsstrahlung photons are not involved in the demagnetization process, and suggest that the star density owing to the photoneutrons is strongly correlated with the demagnetization process.

  10. Mechanism of instability of carbides in Fe–TaC alloy under high energy electron irradiation at 673 K

    Energy Technology Data Exchange (ETDEWEB)

    Abe, Hiroaki, E-mail: abe.hiroaki@imr.tohoku.ac.jp [Institute for Materials Research, Tohoku University, 2-1-1 Katahira, Aoba, Sendai, Miyagi 980-8577 (Japan); Ishizaki, Takahiro [Graduate School of Engineering, Tohoku University, 6-6 Aramaki Aza Aoba, Aoba, Sendai, Miyagi 980-8579 (Japan); Kano, Sho [Institute for Materials Research, Tohoku University, 2-1-1 Katahira, Aoba, Sendai, Miyagi 980-8577 (Japan); Li, Feng [Graduate School of Engineering, Tohoku University, 6-6 Aramaki Aza Aoba, Aoba, Sendai, Miyagi 980-8579 (Japan); Satoh, Yuhki [Institute for Materials Research, Tohoku University, 2-1-1 Katahira, Aoba, Sendai, Miyagi 980-8577 (Japan); Tanigawa, Hiroyasu; Hamaguchi, Dai [Japan Atomic Energy Agency, Rokkasho 039-3212 (Japan); Nagase, Takeshi; Yasuda, Hidehiro [Research Center for Ultra-High Voltage Electron Microscopy, Osaka University, 7-1 Mihogaoka, Ibaraki, Osaka 567-0047 (Japan)

    2014-12-15

    Highlights: • Fe–TaC alloy was fabricated as a model alloy for F82H steel. • Instability of TaC in Fe was observed under high energy electron irradiation at 673 K. • The rate of shrinkage depended on energy, flux, degree of beam focus. • Displacement of Ta in TaC, or radiation-enhanced diffusion of Ta are the mechanism of instability. - Abstract: Reduced activation ferritic/martensitic steels (RAFMs), such as F82H steel, are designed to enhance the high-temperature strength by formation of MX-type nanometer-scale precipitates, mainly TaC. However, their instability under irradiation was recently reported. The purpose of this work, therefore, is to clarify the mechanism employing simultaneous observations under electron irradiation at elevated temperature in a high voltage electron microscope. In this work, Fe-0.2 wt.% TaC was fabricated as a model alloy of F82H steel. The instability of the precipitates was observed under electron irradiation at 1 MeV or above. The remarkable shrinkage and disappearance were clearly observed under irradiation with 1.5 MeV and above. On the contrary, the precipitates were mostly stable below 0.75 MeV. Two kinds of mechanism of the irradiation-induced instability were deduced from the electron-energy dependence. One is the dissolution and diffusion of tantalum from precipitates in ferrite matrix. The other is the displacements of tantalum in precipitates that introduce dissolution of Ta into matrix.

  11. 电容器级钽粉关键技术与开发研究%The Key Technique and R & D of Capacitor Grade Tantalum Powder

    Institute of Scientific and Technical Information of China (English)

    何季麟; 张学清; 杨国启; 郑爱国

    2014-01-01

    This paper cites the characteristics of tantalum capacitors,applications and application characteristics of alu-minum capacitors and multilayer ceramic capacitors.It analyzes the new trends that the chip-based and miniaturization tantalum capacitors led capacitor grade tantalum powder to higher capacity.It describes the challenges of the demand for high reliability in high-voltage tantalum powder of aviation,aerospace and military field voltage capacitor to a higher volt-age and lower ESR direction.It reviews the application development process of the capacitor tantalum powder with high ca-pacitance tantalum powder,high voltage tantalum powder and medium voltage (flake)tantalum powder.It analyzes the performance,product grades and key technologies of high capacitance tantalum powder,high voltage tantalum powder and medium voltage(flake)tantalum powder by methods of the classical methods of potassium tantalum fluoride (K2TaF7)so-dium metal reduction,electron beam melting and ball milled production.For 30~80 kμFV/g tantalum powder,the influ-ence factors of withstand voltage performance have been analyzed.Finally,it presents new technologies,devices,prod-ucts morphology,performance,advantages and disadvantages of the high capacitance tantalum powder and high voltage technology.On the basis of capacitor grade tantalum powder,this paper points out sustainable development ideas of higher capacitance and higher voltage for tantalum capacitors.%引述了Ta电容器与Al电容器、多层陶瓷电容器相比突出的性能与应用特征,分析了Ta电容器片式化、小型化促进电容器级Ta粉高比容化发展的新趋势,叙述了航空、航天和军工领域对高压电容器高可靠性能的需求,以及对中高压Ta粉向更高电压、更低SER方向发展的引领,回顾了电容器用高比容Ta粉、中高压Ta粉发展应用进程,介绍了经典氟钽酸钾(K2 TaF7)金属Na还原法、电子束熔炼法、球磨片式化法生产的高

  12. Graphenated tantalum(IV) oxide and poly(4-styrene sulphonic acid)-doped polyaniline nanocomposite as cathode material in an electrochemical capacitor

    CSIR Research Space (South Africa)

    Njomo, N

    2014-05-01

    Full Text Available Nanostructured poly(4-styrene sulphonic acid) and tantalum (IV) oxide-doped polyaniline nanocomposite were synthesised and their electro-conductive properties were determined. The oxide was synthesized using a modified sol-gel method...

  13. Stereotactic Irradiation of Lung Cancer

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    To investigate the best stereotactic irradiation (STI) technique in treatment of small lung tumors, using dose-volume statistics. Methods: Dose-volume histogram (DVH) of the study phantom consisting of CT using the software of FOCUS-3D planning system. The beam was a 6MV X-ray from a Varian 2300C. The analysis data of Dose-volume statistics was from the technique used for: (1) 2- 12 arcs; (2) 20° - 45° separation angle of arcs; (3) 80° - 160° of gantry rotation. Then we studied the difference of DVH with various irradiation techniques and the influence of target positions and field size by calculated to the distribution of dose from 20%- 90% of the six targets in the lung with 3×3 cm2, 4′ 4 cm2 and 5′ 5 cm2 field size. Results: The volume irradiated pulmonary tissue was the smallest using a six non-coplanar 120° arcs with 30° separation between arcs in the hypothetical set up, the non-coplanar SRI was superiority than conventional one's. The six targets were chosen in the right lung, the volume was the largest in geometric center and was decreased in hilus, bottom, anterior chest wall, lateral wall and apex of the lung in such an order. The DVH had significant change with an increasing field size. Conclusion: the irradiation damage of normal pulmonary tissue was the lowest using the six non-coplanar 120° arcs with a 30° separation between arcs by <5×5 cm2 field and the position of target was not a restricting factor.

  14. [(≡SiO)TaV (=CH2)Cl2], the first tantalum methylidene species prepared and identified on the silica surface

    KAUST Repository

    Chen, Yin

    2013-11-01

    A novel surface tantalum methylidene [(≡SiO)TaV (=CH 2)Cl2] was obtained via thermal decomposition of the well-defined surface species [(≡SiO)TaVCl2Me 2]. This first surface tantalum methylidene ever synthesized has been fully characterized and the kinetics of the a-hydrogen abstraction reaction has also been investigated in the heterogeneous system. © 2013 Elsevier B.V. All rights reserved.

  15. Non-equilibrium molecular dynamics simulations of spall in single crystal tantalum

    Science.gov (United States)

    Hahn, Eric N.; Germann, Timothy C.; Ravelo, Ramon J.; Hammerberg, James E.; Meyers, Marc A.

    2017-01-01

    Ductile tensile failure of tantalum is examined through large scale non-equilibrium molecular dynamics simulations. Several loading schemes including flyer plate impact, decaying shock loading via a frozen piston, and quasi-isentropic (constant strain-rate) expansion are employed to span tensile strain-rates of 108 to 1014 per second. Single crystals of orientation are specifically evaluated to eliminate grain boundary effects. Heterogeneous void nucleation occurs principally at the intersection of deformation twins in single crystals. At high strain rates, multiple spall events occur throughout the material and voids continue to nucleate until relaxation waves arrive from adjacent events. At ultra-high strain rates, those approaching or exceeding the atomic vibrational frequency, spall strength saturates near the maximum theoretical spall strength.

  16. Thermal degradation of ultrabroad bismuth NIR luminescence in bismuth-doped tantalum germanate laser glasses.

    Science.gov (United States)

    Wang, Liping; Zhao, Yanqi; Xu, Shanhui; Peng, Mingying

    2016-04-01

    Because of ultra-broadband luminescence in 1000-1700 nm and consequent applications in fiber amplifier and lasers in the new spectral range where traditional rare earth cannot work, bismuth-doped laser glasses have received rising interest recently. For long-term practical application, thermal degradation must be considered for the glasses. This, however, has seldom been investigated. Here we report the thermal degradation of bismuth-doped germanate glass. Heating and cooling cycle experiments at high temperature reveal strong dependence of the thermal degradation on glass compositions. Bismuth and tantalum lead to the reversible degradation, while lithium can produce permanent irreversible degradation. The degradation becomes worse as lithium content increases in the glass. Absorption spectra show this is due to partial oxidation of bismuth near-infrared emission center. Surprisingly, we notice the emission of bismuth exhibits blueshift, rather than redshift at a higher temperature, and the blueshift can be suppressed by increasing the lithium content.

  17. INTERACTION OF INTERSTITIAL CLUSTERS WITH RHENIUM, OSMIUM, AND TANTALUM IN TUNGSTEN

    Energy Technology Data Exchange (ETDEWEB)

    Setyawan, Wahyu; Nandipati, Giridhar; Kurtz, Richard J.

    2016-09-01

    In the previous semi annual report, we explored the stability of interstitial clusters in W up to size seven. In this report, we study the binding of those clusters to Re, Os, and Ta atoms. For each cluster size, the three most stable configurations are considered to average the binding property. The average binding energy to a Re decreases from 0.79 eV for a size-1 cluster (a [111] dumbbell) to 0.65 eV for a size-7 cluster. For Os, the binding decreases from 1.61 eV for a [111] dumbbell to 1.34 eV for a size-7 cluster. Tantalum is repulsive to interstitial clusters with binding energy ranges from -0.61 eV for a [111] dumbbell to -0.5 eV for a size-7 cluster.

  18. Examination of the damage and failure response of tantalum and copper under varied shock loading conditions

    Energy Technology Data Exchange (ETDEWEB)

    Bronkhorst, Curt A [Los Alamos National Laboratory; Dennis - Koller, Darcie [Los Alamos National Laboratory; Cerreta, Ellen K [Los Alamos National Laboratory; Gray Ill, George T [Los Alamos National Laboratory; Bourne, Neil [AWE-ALDERMASTON

    2010-12-16

    A number of plate impact experiments have been conducted on high purity polycrystalline tantalum and copper samples using graded flyer plate configurations to alter the loading profile. These experiments are designed in a way so that a broad range of damage regimes are probed. The results show that the nucleation of damage primarily occurs at the grain boundaries of the materials. This affords us the opportunity to propose a porosity damage nucleation criterion which begins to account for the length scales of the microstructure (grain size distribution) and the mechanical response of the grain boundary regions (failure stress distribution). This is done in the context of a G-T-N type model for the ductile damage and failure response of both the materials examined. The role of micro-inertial effects on the porosity growth process is also considered.

  19. Examination of the damage and failure response of tantalum and copper under varied shock loading conditions

    Energy Technology Data Exchange (ETDEWEB)

    Bronkhorst, Curt A [Los Alamos National Laboratory; Dennis - Koller, Darcie [Los Alamos National Laboratory; Cerreta, Ellen K [Los Alamos National Laboratory; Gray Ill, George T [Los Alamos National Laboratory; Bourne, Neil [AWE-ALDERMASTON

    2010-12-16

    A number of plate impact experiments have been conducted on high purity polycrystalline tantalum and copper samples using graded flyer plate configurations to alter the loading profile. These experiments are designed in a way so that a broad range of damage regimes are probed. The results show that the nucleation of damage primarily occurs at the grain boundaries of the materials. This affords us the opportunity to propose a porosity damage nucleation criterion which begins to account for the length scales of the microstructure (grain size distribution) and the mechanical response of the grain boundary regions (failure stress distribution). This is done in the context of a G-T-N type model for the ductile damage and failure response of both the materials examined. The role of micro-inertial effects on the porosity growth process is also considered.

  20. Investigation and modeling of the anomalous yield point phenomenon in pure tantalum

    Energy Technology Data Exchange (ETDEWEB)

    Colas, D. [Laboratoire Interdisciplinaire Carnot de Bourgogne, UMR 5209 CNRS, Université de Bourgogne, 9 avenue Alain Savary, BP 17870, 21078 Dijon Cedex (France); CEA Valduc, 21120 Is-sur-Tille (France); Mines ParisTech, Centre des Matériaux, CNRS, UMR 7633, BP 87, 91003 Evry Cedex (France); Finot, E. [Laboratoire Interdisciplinaire Carnot de Bourgogne, UMR 5209 CNRS, Université de Bourgogne, 9 avenue Alain Savary, BP 17870, 21078 Dijon Cedex (France); Flouriot, S. [CEA Valduc, 21120 Is-sur-Tille (France); Forest, S. [Mines ParisTech, Centre des Matériaux, CNRS, UMR 7633, BP 87, 91003 Evry Cedex (France); Mazière, M., E-mail: matthieu.maziere@mines-paristech.fr [Mines ParisTech, Centre des Matériaux, CNRS, UMR 7633, BP 87, 91003 Evry Cedex (France); Paris, T. [CEA Valduc, 21120 Is-sur-Tille (France)

    2014-10-06

    The monotonic and cyclic behavior of commercially pure tantalum has been investigated at room temperature, in order to capture and understand the occurrence of the anomalous yield point phenomenon. Interrupted tests have been performed, with strain reversals (tensile or compressive loading) after an aging period. The stress drop is attributed to the interactions between dislocations and solute atoms (oxygen) and its macroscopic occurrence is not systematically observed. InfraRed Thermography (IRT) measurements supported by Scanning Electron Microscopy (SEM) pictures of the polished gauge length of a specimen during an interrupted tensile test reveal the nucleation and propagation of a strain localization band. The KEMC (Kubin–Estrin–McCormick) phenomenological model accounting for strain aging has been identified for several loadings and strain rates at room temperature. Simulations on full specimen using the KEMC model do not show strain localization, because of the competition between viscosity and strain localization. However, a slight misalignment of the sample can promote strain localization.

  1. Thermodynamic and mechanical stabilities of tantalum nitride Ta2N3

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Chao [Los Alamos National Laboratory; Lin, Zhijun [Los Alamos National Laboratory; Zhao, Yusheng [Los Alamos National Laboratory

    2009-01-01

    We perform first-principles density functional calculations on a newly discovered tantalum nitride with an orthorhombic U{sub 2}S{sub 3} structure to assess its thermodynamic and mechanical stabilities. Our random search unveils a tetragonal Ta{sub 2}N{sub 3} structure that is energetically more favorable than an orthorhombic Ta{sub 2}N{sub 3} at zero pressure. We predict that the tetragonal Ta{sub 2}N{sub 3} transforms into the orthorhombic phase above a relatively low pressure of 7.7 GPa. Single-crystal elastic constant calculations reveal that orthorhombic Ta{sub 2}N{sub 3} is mechanically unstable because of a negative c{sub 66}. Our calculations suggest that minor oxygen substitution for nitrogen plays an important role in stabilizing the orthorhombic Ta{sub 2}N{sub 3} structure.

  2. Influence of Deposition Parameters on Surface Evolution of Sputtered Tantalum Thin Films

    Institute of Scientific and Technical Information of China (English)

    LUO Xiang-dong; LUO Chong-tai

    2008-01-01

    Tantalum thin films with different thicknesses varying from 50 nm to 600 nm were deposited on Si substrates by radio frequency magnetron sputtering as functions of deposition temperature(Ts) and bias voltage(Ub). Surface roughness and its dynamic evolution behavior were quantitatively investigated by using atomic force microscopy(AFM). With increasing Ts from 300 K to 600 K, surface roughness Rrms and dynamic exponent β decreases gradually. With the increase of Ub from 0 V to -150 V, Rrms and β first decrease and then increase. The dependence of Ts and Ub on the film surface evolution has been discussed in terms of surface diffusion, mound growth, and ion impinging effect.

  3. Oxidative Desulfurization of Dibenzothiophene Using Dawson Type Heteropoly Compounds/Tantalum as Catalyst

    OpenAIRE

    Mohadi, Risfidian; Teresia, Lusi; Fithri, Najma Annuria; Lesbani, Aldes; Hidayati, Nurlisa

    2016-01-01

    Catalyst (NH4)6[b-P2W18O62]/Ta has been synthesized by simple wet impregnation at 30-40 °C under atmospheric conditions using Dawson type polyoxometalate (NH4)6[b-P2W18O62] and tantalum. The catalyst was characterized by FTIR spectrophotometer, XRD, SEM, and N2 adsorption desorption methods. FTIR spectrum of (NH4)6[b-P2W18O62]/Ta showed that Dawson type polyoxometalate (NH4)6[b-P2W18O62] and Ta was successfully impregnated which was indicated by vibration spectrum at wavenumber of 900-1100 cm...

  4. Growth and characteristics of tantalum oxide thin films deposited using thermionic vacuum arc technology

    Science.gov (United States)

    Vladoiu, Rodica; Ciupina, Victor; Mandes, Aurelia; Dinca, Virginia; Prodan, Madalina; Musa, Geavit

    2010-11-01

    Tantalum pentoxide (Ta2O5) thin films were synthesized using thermionic vacuum arc (TVA) technology. TVA is an original deposition method using a combination of anodic arc and electron gun system for the growth of thin films from solid precursors under vacuum of 10-6 Torr. The properties of the deposited Ta2O5 thin films were investigated in terms of wettability, refractive index, morphology, and structure. The surface free energy was determined by means of surface energy evaluation system indicating a hydrophilic character and the refractive index was measured by Filmetrics F20 device. The morphology was determined from bright field transmission electron microscopy (TEM) image performed by Philips CM 120 ST TEM system. It exhibits nanoparticles of 3-6 nm diameter smoothly distributed. Selected area electron diffraction pattern revealed the contrast fringes given by complex polycrystalline particles included in the amorphous film. The measured fringes could be indexed using monoclinic structure of Ta2O5.

  5. Melting curves and structural properties of tantalum from the modified-Z method

    Science.gov (United States)

    Liu, C. M.; Xu, C.; Cheng, Y.; Chen, X. R.; Cai, L. C.

    2015-12-01

    The melting curves and structural properties of tantalum (Ta) are investigated by molecular dynamics simulations combining with potential model developed by Ravelo et al. [Phys. Rev. B 88, 134101 (2013)]. Before calculations, five potentials are systematically compared with their abilities of producing reasonable compressional and equilibrium mechanical properties of Ta. We have improved the modified-Z method introduced by Wang et al. [J. Appl. Phys. 114, 163514 (2013)] by increasing the sizes in Lx and Ly of the rectangular parallelepiped box (Lx = Ly ≪ Lz). The influences of size and aspect ratio of the simulation box to melting curves are also fully tested. The structural differences between solid and liquid are detected by number density and local-order parameters Q6. Moreover, the atoms' diffusion with simulation time, defects, and vacancies formations in the sample are all studied by comparing situations in solid, solid-liquid coexistence, and liquid state.

  6. Study of two tantalum Taylor impact specimens using experiments and stochastic polycrystal plasticity simulation

    Energy Technology Data Exchange (ETDEWEB)

    Tonks, Michael R [Los Alamos National Laboratory

    2008-01-01

    We compare the experimentally obtained response of two cylindrical tantalum Taylor impact specimens. The first specimen is manufactured using a powder metallurgy (P/M) process with a random initial texture and relatively equiaxed crystals. The second is sectioned from a roundcorner square rolled (RCSR) rod with an asymmetric texture and elongated crystals. The deformed P/M specimen has an axisymmetric footprint while the deformed RCSR projectile has an eccentric footprint with distinct corners. Also, the two specimens experienced similar crystallographic texture evolution, though the RCSR specimen experienced greater plastic deformation. Our simulation predictions mimic the texture and deformation data measured from the P/M specimen. However, our RCSR specimen simulations over-predict the texture development and do not accurately predict the deformation, though the deformation prediction is improved when the texture is not allowed to evolve. We attribute this discrepancy to the elongated crystal morphology in the RCSR specimen which is not represented in our mean-field model.

  7. The ISOLDE target robots

    CERN Multimedia

    Maximilein Brice

    2002-01-01

    ISOLDE targets need to be changed frequently, around 80 times per year. The high radiation levels do not permit this to be done by human hands and the target changes are effected by 2 industrial robots (picture _01). On the left, in the distance, the front-end of the GPS (General Purpose Separator) is seen, while the HRS (High Resolution Separator) is at the right. Also seen are the doors to the irradiated-target storage.

  8. The physicochemical/biological properties of porous tantalum and the potential surface modification techniques to improve its clinical application in dental implantology

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Yindong [State Key Laboratory of Oral Diseases, West China Hospital of Stomatology, Sichuan University, Chengdu (China); Bao, Chongyun, E-mail: cybao9933@scu.edu.cn [State Key Laboratory of Oral Diseases, West China Hospital of Stomatology, Sichuan University, Chengdu (China); Wismeijer, Daniel [Department of Oral Implantology and Prosthetic Dentistry, Academic Centre for Dentistry Amsterdam (ACTA), MOVE Research Institute Amsterdam, VU University Amsterdam and University of Amsterdam, Amsterdam (Netherlands); Wu, Gang, E-mail: g.wu@acta.nl [Department of Oral Implantology and Prosthetic Dentistry, Academic Centre for Dentistry Amsterdam (ACTA), MOVE Research Institute Amsterdam, VU University Amsterdam and University of Amsterdam, Amsterdam (Netherlands)

    2015-04-01

    More rapid restoration and more rigid functionality have been pursued for decades in the field of dental implantology. Under such motivation, porous tantalum has been recently introduced to design a novel type of dental implant. Porous tantalum bears interconnected porous structure with pore size ranging from 300 to 600 μm and a porosity of 75–85%. Its elastic modulus (1.3–10 GPa) more closely approximates that of natural cortical (12–18 GPa) and cancellous bone (0.1–0.5 GPa) in comparison with the most commonly used dental materials, such as titanium and titanium alloy (106–115 GPa). Porous tantalum is highly corrosion-resistant and biocompatible. It can significantly enhance the proliferation and differentiation of primary osteoblasts derived from elderly people than titanium. Porous tantalum can allow bone ingrowth and establish not only osseointegration but also osseoincorporation, which will significantly enhance the secondary stability of implants in bone tissue. In this review, we summarize the physicochemical, mechanical and biological properties of porous tantalum. We further discuss the performance of current tantalum dental implants and present the methodologies of surface modifications in order to improve their biological performance.

  9. Fabrication and characterization of powder metallurgy tantalum components prepared by high compaction pressure technique

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Youngmoo [Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology, 291 Daehak-ro, Yuseong-gu, Daejeon 34141 (Korea, Republic of); Agency for Defense Development, Yuseong, P.O. Box 35, Yuseong-gu, Daejeon 34186, Republic of Korea. (Korea, Republic of); Lee, Dongju [Korea Atomic Energy Research Institute, 111 Daedeok-daero, Yuseong-gu, Daejeon 34057 (Korea, Republic of); Hwang, Jaewon [Samsung Electronics, 129 Samsung-ro, Youngtong-gu, Suwon 16677 (Korea, Republic of); Ryu, Ho Jin, E-mail: hojinryu@kaist.ac.kr [Department of Nuclear and Quantum Engineering, Korea Advanced Institute of Science and Technology, 291 Daehak-ro, Yuseong-gu, Daejeon 34141 (Korea, Republic of); Hong, Soon Hyung, E-mail: shhong@kaist.ac.kr [Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology, 291 Daehak-ro, Yuseong-gu, Daejeon 34141 (Korea, Republic of)

    2016-04-15

    The present study has investigated the consolidation behaviors of tantalum powders during compaction and sintering, and the characteristics of sintered components. For die compaction, the densification behaviors of the powders are simulated by finite element analyses based on the yield function proposed by Shima and Oyane. Accordingly, the green density distribution for coarser particles is predicted to be more uniform because they exhibits higher initial relative tap density owing to lower interparticle friction. It is also found that cold isostatic pressing is capable of producing higher dense compacts compared to the die pressing. However, unlike the compaction behavior, the sintered density of smaller particles is found to be higher than those of coarser ones owing to their higher specific surface area. The maximum sintered density was found to be 0.96 of theoretical density where smaller particles were pressed isostatically at 400 MPa followed by sintering at 2000 °C. Moreover, the effects of processing conditions on grain size and texture were also investigated. The average grain size of the sintered specimen is 30.29 μm and its texture is less than 2 times random intensity. Consequently, it is concluded that the higher pressure compaction technique is beneficial to produce high dense and texture-free tantalum components compared to hot pressing and spark plasma sintering. - Highlights: • Higher Ta density is obtained from higher pressure and sintering temperature. • High compaction method enables P/M Ta to achieve the density of 16.00 g·cm{sup −3}. • A P/M Ta component with fine microstructure and random orientation is developed.

  10. High-rate Plastic Deformation of Nanocrystalline Tantalum to Large Strains: Molecular Dynamics Simulation

    Energy Technology Data Exchange (ETDEWEB)

    Rudd, R E

    2009-02-05

    Recent advances in the ability to generate extremes of pressure and temperature in dynamic experiments and to probe the response of materials has motivated the need for special materials optimized for those conditions as well as a need for a much deeper understanding of the behavior of materials subjected to high pressure and/or temperature. Of particular importance is the understanding of rate effects at the extremely high rates encountered in those experiments, especially with the next generation of laser drives such as at the National Ignition Facility. Here we use large-scale molecular dynamics (MD) simulations of the high-rate deformation of nanocrystalline tantalum to investigate the processes associated with plastic deformation for strains up to 100%. We use initial atomic configurations that were produced through simulations of solidification in the work of Streitz et al [Phys. Rev. Lett. 96, (2006) 225701]. These 3D polycrystalline systems have typical grain sizes of 10-20 nm. We also study a rapidly quenched liquid (amorphous solid) tantalum. We apply a constant volume (isochoric), constant temperature (isothermal) shear deformation over a range of strain rates, and compute the resulting stress-strain curves to large strains for both uniaxial and biaxial compression. We study the rate dependence and identify plastic deformation mechanisms. The identification of the mechanisms is facilitated through a novel technique that computes the local grain orientation, returning it as a quaternion for each atom. This analysis technique is robust and fast, and has been used to compute the orientations on the fly during our parallel MD simulations on supercomputers. We find both dislocation and twinning processes are important, and they interact in the weak strain hardening in these extremely fine-grained microstructures.

  11. Structure dependent resistivity and dielectric characteristics of tantalum oxynitride thin films produced by magnetron sputtering

    Energy Technology Data Exchange (ETDEWEB)

    Cristea, D., E-mail: daniel.cristea@unitbv.ro [Department of Materials Science, Transilvania University, 500036 Brasov (Romania); Crisan, A. [Department of Materials Science, Transilvania University, 500036 Brasov (Romania); Cretu, N. [Electrical Engineering and Applied Physics Department, Transilvania University, 500036 Brasov (Romania); Borges, J. [Centro de Física, Universidade do Minho, Campus de Gualtar, 4710 - 057 Braga (Portugal); Instituto Pedro Nunes, Laboratório de Ensaios, Desgaste e Materiais, Rua Pedro Nunes, 3030-199 Coimbra (Portugal); SEG-CEMUC, Mechanical Engineering Department, University of Coimbra, 3030-788 Coimbra (Portugal); Lopes, C.; Cunha, L. [Centro de Física, Universidade do Minho, Campus de Gualtar, 4710 - 057 Braga (Portugal); Ion, V.; Dinescu, M. [National Institute for Lasers, Plasma and Radiation Physics, Lasers Department, “Photonic Processing of Advanced Materials” Group, PO Box MG-16, RO 77125 Magurele-Bucharest (Romania); Barradas, N.P. [Centro de Ciências e Tecnologias Nucleares, Instituto Superior Técnico, Universidade de Lisboa, E.N. 10 ao km 139,7, 2695-066 Bobadela LRS (Portugal); Alves, E. [Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade de Lisboa, E.N. 10 ao km 139,7, 2695-066 Bobadela LRS (Portugal); Apreutesei, M. [MATEIS Laboratory-INSA de Lyon, 21 Avenue Jean Capelle, 69621 Villeurbanne cedex (France); Université de Lyon, Institut des Nanotechnologies de Lyon INL-UMR5270, CNRS, Ecole Centrale de Lyon, Ecully F-69134 (France); Munteanu, D. [Department of Materials Science, Transilvania University, 500036 Brasov (Romania)

    2015-11-01

    Highlights: • Tantalum oxynitride thin films have been deposited by magnetron sputtering, in various configurations. • The rising of the reactive gases mixture flow has the consequence of a gradual increase in the non-metallic content in the films, which results in a 10 orders of magnitude resistivity domain. • The higher resistivity films exhibit dielectric constants up to 41 and quality factors up to 70. - Abstract: The main purpose of this work is to present and to interpret the change of electrical properties of Ta{sub x}N{sub y}O{sub z} thin films, produced by DC reactive magnetron sputtering. Some parameters were varied during deposition: the flow of the reactive gases mixture (N{sub 2} and O{sub 2}, with a constant concentration ratio of 17:3); the substrate voltage bias (grounded, −50 V or −100 V) and the substrate (glass, (1 0 0) Si or high speed steel). The obtained films exhibit significant differences. The variation of the deposition parameters induces variations of the composition, microstructure and morphology. These differences cause variation of the electrical resistivity essentially correlated with the composition and structural changes. The gradual decrease of the Ta concentration in the films induces amorphization and causes a raise of the resistivity. The dielectric characteristics of some of the high resistance Ta{sub x}N{sub y}O{sub z} films were obtained in the samples with a capacitor-like design (deposited onto high speed steel, with gold pads deposited on the dielectric Ta{sub x}N{sub y}O{sub z} films). Some of these films exhibited dielectric constant values higher than those reported for other tantalum based dielectric films.

  12. Effects of Processing Variables on Tantalum Nitride by Reactive-Ion-Assisted Magnetron Sputtering Deposition

    Science.gov (United States)

    Wei, Chao‑Tsang; Shieh, Han‑Ping D.

    2006-08-01

    The binary compound tantalum nitride (TaN) and ternary compounds tantalum tungsten nitrides (Ta1-xWxNy) exhibit interesting properties such as high melting point, high hardness, and chemical inertness. Such nitrides were deposited on a tungsten carbide (WC) die and silicon wafers by ion-beam-sputter evaporation of the respective metal under nitrogen ion-assisted deposition (IAD). The effects of N2/Ar flux ratio, post annealing, ion-assisted deposition, deposition rate, and W doping in coating processing variables on hardness, load critical scratching, oxidation resistance, stress and surface roughness were investigated. The optimum N2/Ar flux ratios in view of the hardness and critical load of TaN and Ta1-xWxNy films were ranged from 0.9 to 1.0. Doping W into TaN to form Ta1-xWxNy films led significant increases in hardness, critical load, oxidation resistance, and reduced surface roughness. The optimum doping ratio was [W/(W+Ta)]=0.85. From the deposition rate and IAD experiments, the stress in the films is mainly contributed by sputtering atoms. The lower deposition rate at a high N2/Ar flux ratio resulted in a higher compressive stress. A high compressive residual stress accounts for a high hardness. The relatively high compressive stress was attributed primarily to peening by atoms, ions and electrons during film growth, the Ta1-xWxNy films showed excellent hardness and strength against a high temperature, and sticking phenomena can essentially be avoided through their use. Ta1-xWxNy films showed better performance than the TaN film in terms of mechanical properties and oxidation resistance.

  13. Synthesis of chemical vapor deposition graphene on tantalum wire for supercapacitor applications

    Energy Technology Data Exchange (ETDEWEB)

    Li, Mingji, E-mail: limingji@163.com [Tianjin Key Laboratory of Film Electronic and Communicate Devices, School of Electronics Information Engineering, Tianjin University of Technology, Tianjin 300384 (China); Guo, Wenlong [Tianjin Key Laboratory of Film Electronic and Communicate Devices, School of Electronics Information Engineering, Tianjin University of Technology, Tianjin 300384 (China); Li, Hongji, E-mail: hongjili@yeah.net [Tianjin Key Laboratory of Organic Solar Cells and Photochemical Conversion, School of Chemistry and Chemical Engineering, Tianjin University of Technology, Tianjin 300384 (China); Xu, Sheng [School of Precision Instrument and Optoelectronics Engineering, Tianjin University, Tianjin 300072 (China); Qu, Changqing; Yang, Baohe [Tianjin Key Laboratory of Film Electronic and Communicate Devices, School of Electronics Information Engineering, Tianjin University of Technology, Tianjin 300384 (China)

    2014-10-30

    Highlights: • The capacitance of graphene/tantalum (Ta) wire electrodes is firstly reported. • Graphene was grown on the Ta surface by hot-filament chemical vapor deposition. • Graphene/Ta wire structure is favorable for fast ion and electron transfer. • The graphene/Ta wire electrode shows high capacitive properties. - Abstract: This paper studies the synthesis and electrochemical characterization of graphene/tantalum (Ta) wires as high-performance electrode material for supercapacitors. Graphene on Ta wires is prepared by the thermal decomposition of methane under various conditions. The graphene nanosheets on the Ta wire surface have an average thickness of 1.3–3.4 nm and consist typically of a few graphene monolayers, and TaC buffer layers form between the graphene and Ta wire. A capacitor structure is fabricated using graphene/Ta wire with a length of 10 mm and a diameter of 0.6 mm as the anode and Pt wire of the same size as the cathode. The electrochemical behavior of the graphene/Ta wires as supercapacitor electrodes is characterized by cyclic voltammetry, galvanostatic charge/discharge, and electrochemical impedance spectroscopy in 1 M Na{sub 2}SO{sub 4} aqueous electrolyte. The as-prepared graphene/Ta electrode has highest capacitance of 345.5 F g{sup −1} at current density of 0.5 A g{sup −1}. The capacitance remains at about 84% after 1000 cycles at 10 A g{sup −1}. The good electrochemical performance of the graphene/Ta wire electrode is attributed to the unique nanostructural configuration, high electrical conductivity, and large specific surface area of the graphene layer. This suggests that graphene/Ta wire electrode materials have potential applications in high-performance energy storage devices.

  14. Clinical and radiographic evaluation of single tantalum dental implants: a prospective pilot clinical study

    Science.gov (United States)

    DE FRANCESCO, M.; GOBBATO, E.A.; NOCE, D.; CAVALLARI, F.; FIORETTI, A.

    2016-01-01

    SUMMARY Objective The aim of this prospective pilot clinical case series report was to evaluate, through a clinical and radiographic analysis, the peri-implant bone resorption of the tantalum dental implants (TMT) (Zimmer TMT, Parsippany, NJ, USA) one year after prosthetic rehabilitation. Methods Twenty tantalum dental implants were placed in both maxillas and mandibles of 20 patients. Patients were asked to attend a radiographic and clinical follow-up and their previous clinical records and X-rays were assessed. Bone levels were calculated by digitally measuring the distance from the implant shoulder to the first bone-to-implant on periapical radiographs taken at surgery and after 6 and 12 months of functioning. The Pearson correlation analysis was performed to assess it there was a correlation between the measurement of the marginal bone loss (MBL). The Anova Test with a post-hoc analysis using Bonferroni’s test was used to compare the three group (0, 6 months and 12 months). Results The mean total MBL for the group 0 months was 0.84 mm (SD 0.21), 6 months was 0.87 mm (SD 0.22) and for 12 months was 0.89 mm (SD 0.23). The values of the Pearson’s coefficients showed that the data measurement were positively correlated. The Anova test showed a statistically significant difference between the groups. Conclusion The statistically significant difference in marginal bone loss can be considered physiological. Within the limits of this study it can be concluded that TMT implants have an excellent bone crest’s stability, however, to have most accurate information, will be necessary extend the sample. PMID:28280531

  15. Food irradiation makes progress

    Energy Technology Data Exchange (ETDEWEB)

    Kooij, J. van (Joint FAO/IAEA Div. of Isotope and Radiation Applications of Atomic Energy for Food and Agricultural Development, Vienna (Austria))

    1984-06-01

    In the past fifteen years, food irradiation processing policies and programmes have been developed both by a number of individual countries, and through projects supported by FAO, IAEA and WHO. These aim at achieving general acceptance and practical implementation of food irradiation through rigorous investigations of its wholesomeness, technological and economic feasibility, and efforts to achieve the unimpeded movement of irradiated foods in international trade. Food irradiation processing has many uses.

  16. Temperature-dependent surface modification of Ta due to high-flux, low-energy He+ ion irradiation

    Science.gov (United States)

    Novakowski, T. J.; Tripathi, J. K.; Hassanein, A.

    2015-12-01

    This work examines the response of Tantalum (Ta) as a potential candidate for plasma-facing components (PFCs) in future nuclear fusion reactors. Tantalum samples were exposed to high-flux, low-energy He+ ion irradiation at different temperatures in the range of 823-1223 K. The samples were irradiated at normal incidence with 100 eV He+ ions at constant flux of 1.2 × 1021 ions m-2 s-1 to a total fluence of 4.3 × 1024 ions m-2. An additional Ta sample was also irradiated at 1023 K using a higher ion fluence of 1.7 × 1025 ions m-2 (at the same flux of 1.2 × 1021 ions m-2 s-1), to confirm the possibility of fuzz formation at higher fluence. This higher fluence was chosen to roughly correspond to the lower fluence threshold of fuzz formation in Tungsten (W). Surface morphology was characterized with a combination of field-emission scanning electron microscopy (FE-SEM) and atomic force microscopy (AFM). These results demonstrate that the main mode of surface damage is pinholes with an average size of ∼70 nm2 for all temperatures. However, significantly larger pinholes are observed at elevated temperatures (1123 and 1223 K) resulting from the agglomeration of smaller pinholes. Ex situ X-ray photoelectron spectroscopy (XPS) provides information about the oxidation characteristics of irradiated surfaces, showing minimal exfoliation of the irradiated Ta surface. Additionally, optical reflectivity measurements are performed to further characterize radiation damage on Ta samples, showing gradual reductions in the optical reflectivity as a function of temperature.

  17. Food irradiation in China

    Energy Technology Data Exchange (ETDEWEB)

    Wedekind, L.

    1986-08-01

    The paper concerns food irradiation in The People's Republic of China. Its use is envisaged to prolong storage times and to improve the quality of specific foodstuffs. Commercialisation in China, demonstration plants, seasonal shortages and losses, Shanghai irradiation centre, health and safety approval, prospects for wider applications and worldwide use of food irradiation, are all discussed.

  18. A novel tantalum-based sol-gel packed microextraction syringe for highly specific enrichment of phosphopeptides in MALDI-MS applications.

    Science.gov (United States)

    Çelikbıçak, Ömür; Atakay, Mehmet; Güler, Ülkü; Salih, Bekir

    2013-08-07

    A new tantalum-based sol-gel material was synthesized using a unique sol-gel synthesis pathway by PEG incorporation into the sol-gel structure without performing a calcination step. This improved its chemical and physical properties for the high capacity and selective enrichment of phosphopeptides from protein digests in complex biological media. The specificity of the tantalum-based sol-gel material for phosphopeptides was evaluated and compared with tantalum(V) oxide (Ta2O5) in different phosphopeptide enrichment applications. The tantalum-based sol-gel and tantalum(V) oxide were characterized in detail using FT-IR spectroscopy, X-ray diffraction (XRD) and scanning electron microscopy (SEM), and also using a surface area and pore size analyzer. In the characterization studies, the surface morphology, pore volume, crystallinity of the materials and PEG incorporation into the sol-gel structure to produce a more hydrophilic material were successfully demonstrated. The X-ray diffractograms of the two different materials were compared and it was noted that the broad signals of the tantalum-based sol-gel clearly represented the amorphous structure of the sol-gel material, which was more likely to create enough surface area and to provide more accessible tantalum atoms for phosphopeptides to be easily adsorbed when compared with the neat and more crystalline structure of Ta2O5. Therefore, the phosphopeptide enrichment performance of the tantalum-based sol-gels was found to be remarkably higher than the more crystalline Ta2O5 in our studies. Phosphopeptides at femtomole levels could be selectively enriched using the tantalum-based sol-gel and detected with a higher signal-to-noise ratio by matrix-assisted laser desorption/ionization-mass spectrometer (MALDI-MS). Moreover, phosphopeptides in a tryptic digest of non-fat bovine milk as a complex real-world biological sample were retained with higher yield using a tantalum-based sol-gel. Additionally, the sol-gel material

  19. Quasi-static Tensile and Compressive Behavior of Nanocrystalline Tantalum Based on Miniature Specimen Testing—Part II: Mechanical Properties

    Science.gov (United States)

    Ligda, J.; D'Antuono, D. Scotto; Taheri, M. L.; Schuster, B. E.; Wei, Q.

    2016-09-01

    In Part I of this work (this issue), we presented the microstructure of tantalum processed by high-pressure torsion (HPT). In this part, we will present results based on site-specific micro-mechanical testing. The experimental techniques were used due to the intrinsic microstructure gradient associated with HPT processing. The primary objective is to explore the grain size effect on the quasi-static mechanical properties of HPT processed tantalum with ultrafine grained (UFG, grain size d 100 nm) and nanocrystalline (NC, d imaging microscopy (OIM) show that the shear bands form by grain rotation. Comparing d in these two regions to the mechanism proposed in the literature shows that reduced d in the shear banding region is more susceptible to localized shearing via grain rotation. This work unifies, or at least further substantiates, the notion that body-centered cubic metals with UFG/NC microstructure tend to have localized shear band even under quasi-static uniaxial compression.

  20. Layered tantalum oxynitride nanorod array carpets for efficient photoelectrochemical conversion of solar energy: experimental and DFT insights.

    Science.gov (United States)

    Allam, Nageh K; Shaheen, Basamat S; Hafez, Ahmed M

    2014-04-09

    Anodically fabricated tantalum oxide (Ta2O5) nanorod array carpets are converted into the corresponding tantalum oxynitride (TaON) through nitridation in an ammonia atmosphere. The measured optical bandgap energy of TaON is ∼2.3 eV, which is also confirmed via the density functional theory calculations. When used to photoelectrochemically split water (AM 1.5G illumination, 1 M KOH, and 0.6 V applied DC bias), the multilayer nanorod films show visible-light incident photon conversion efficiencies (IPCE) as high as 7.5%. The enhanced photochemical activity is discussed in terms of the ordered one-dimensional morphology as well as the electron effective mass in TaON and Ta2O5.

  1. Conflict minerals in the compute sector: estimating extent of tin, tantalum, tungsten, and gold use in ICT products.

    Science.gov (United States)

    Fitzpatrick, Colin; Olivetti, Elsa; Miller, Reed; Roth, Richard; Kirchain, Randolph

    2015-01-20

    Recent legislation has focused attention on the supply chains of tin, tungsten, tantalum, and gold (3TG), specifically those originating from the eastern part of the Democratic Republic of Congo. The unique properties of these so-called “conflict minerals” lead to their use in many products, ranging from medical devices to industrial cutting tools. This paper calculates per product use of 3TG in several information, communication, and technology (ICT) products such as desktops, servers, laptops, smart phones, and tablets. By scaling up individual product estimates to global shipment figures, this work estimates the influence of the ICT sector on 3TG mining in covered countries. The model estimates the upper bound of tin, tungsten, tantalum, and gold use within ICT products to be 2%, 0.1%, 15%, and 3% of the 2013 market share, respectively. This result is projected into the future (2018) based on the anticipated increase in ICT device production.

  2. Other Oxides Pre-removed from Bangka Tin Slag to Produce a High Grade Tantalum and Niobium Oxides Concentrate

    Science.gov (United States)

    Permana, S.; Soedarsono, J. W.; Rustandi, A.; Maksum, A.

    2016-05-01

    Indonesia, as the second largest tin producer in the world, has a byproduct from the production of tin. This byproduct is in the forms of tin slag containing tantalum pentoxide (Ta2O5) and niobium pentoxide (Nb2O5). This study focuses on the recovery of tantalum pentoxide and niobium pentoxide from the tin slag. In the process, one part of the tin slag sample was sieved only (BTS), and the other was roasted at 900°C, water quenched and then sieved (BTS-RQS). Samples BTS and BTS-RQS were characterized by thermo gravimetric analysis (TGA) and X-ray flourence (XRF). One part of BTS-RQS sample was dissolved in hydrofluoric acid (HF) and the other was dissolved in hydrochloric acid (HCl), washed with distilled water, then dissolved into sodium hydroxide (NaOH). Each sample was characterized by using XRF. The BTS sample produced the highest recovery of 0.3807 and 0.6978% for Ta2O5 and Nb2O5, respectively, from the particle size of -1.00+0.71 and a fraction of 47.29%, while BTS-RQS produced the highest recovery of 0.3931 and 0.8994% for Ta2O5 and Nb2O5, respectively, on the particle size of -0.71+0350 and a fraction of 21%. BTS-RQS, dissolved with 8% hydro fluoride acid, yields tantalum pentoxide and niobium pentoxide with a ratio of 2.01 and 2.09, respectively. For the sample BTS-RQS dissolve first with 6M hydrochloric acid, washed with distilled water, then dissolved with sodium hydroxide 10M, the yield ratios are 1.60 and 1.84 for tantalum pentoxide and niobium pentoxide, respectively. In this study, it is found that the dissolution by using hydrofluoric acid 8% yields the best ratio.

  3. In situ production of tantalum carbide nanodispersoids in a copper matrix by reactive milling and hot extrusion

    Energy Technology Data Exchange (ETDEWEB)

    Manotas-Albor, Milton, E-mail: manotasm@uninorte.edu.co [Grupo de Investigación en Física Aplicada, Departamento de Física, Universidad del Norte, Km. 5 vía a Puerto Colombia, Barranquilla (Colombia); Departamento de Ingeniería Mecánica, Facultad de Ciencias Físicas y Matemáticas, Universidad de Chile, Beauchef 850, Santiago (Chile); Vargas-Uscategui, Alejandro [Laboratorio de Materiales a Nanoescala, Departamento de Ciencia de los Materiales, Facultad de Ciencias Físicas y Matemáticas, Universidad de Chile, Tupper Av. 2069, Santiago (Chile); Palma, Rodrigo [Departamento de Ingeniería Mecánica, Facultad de Ciencias Físicas y Matemáticas, Universidad de Chile, Beauchef 850, Santiago (Chile); Mosquera, Edgar [Laboratorio de Materiales a Nanoescala, Departamento de Ciencia de los Materiales, Facultad de Ciencias Físicas y Matemáticas, Universidad de Chile, Tupper Av. 2069, Santiago (Chile)

    2014-06-15

    Highlights: • Tantalum carbide nanodispersoids were obtained in a copper matrix. • Nanodispersoids were obtained by means of reactive milling followed by hot extrusion. • Hexane was used as the liquid medium for the reactive mechanical alloying process. • Hexane provides the carbon (C) needed for the process. • The reaction of tantalum carbide formation takes place in the hot extrusion. - Abstract: This paper presents a study of the in situ production of tantalum carbide nanodispersoids in a copper matrix. The copper matrix composites were produced by means of reactive milling in hexane (C{sub 6}H{sub 14}) followed by hot extrusion. The composite materials were characterized by means of optical emission spectroscopy (OES), X-ray fluorescence (XRF), scanning electron microscopy (SEM), X-ray diffraction (XRD), transmission electron microscopy (TEM) and Vickers micro-hardness. The effect of milling time was analyzed in 10, 20 and 30 h in a composite with a nominal composition Cu–5 vol.% TaC. A systematic increase of the dislocations density and the carbon concentration were observed when the milling time was increased, whereas the crystallite size of the composite matrix decreased. The material milled for 30 h and hot-extruded showed a density of 9037 kg m{sup −3} (98.2% densification) and a softening resistance of 204 HV; however the latter value showed an abrupt drop after an annealing treatment at 923 K for 1 h. Finally, the TEM analysis showed the presence of tantalum carbide (Ta{sub 4}C{sub 3}) nanodispersoids.

  4. Effect of Surface Treatments on Anodic Oxide Film Growth and Electrochemical Properties of Tantalum used for Biomedical Applications

    OpenAIRE

    R.A. Silva; Silva, I. P.; Rondot, B.

    2006-01-01

    Abstract Self-expandable nitinol (nickel-titanium) alloys and 316L stainless steel are the most commonly used materials in the production of coronary stents. However, tantalum (Ta) has already been used to make stents for endovascular surgery and may constitute an alternative to other materials because of its better electrochemical performance, namely its higher corrosion resistance, as well as its radio-op...

  5. Sol-gel synthesis of tantalum oxide and phosphonic acid-modified carbon nanotubes composite coatings on titanium surfaces.

    Science.gov (United States)

    Maho, Anthony; Detriche, Simon; Delhalle, Joseph; Mekhalif, Zineb

    2013-07-01

    Carbon nanotubes used as fillers in composite materials are more and more appreciated for the outstanding range of accessible properties and functionalities they generate in numerous domains of nanotechnologies. In the framework of biological and medical sciences, and particularly for orthopedic applications and devices (prostheses, implants, surgical instruments, …), titanium substrates covered by tantalum oxide/carbon nanotube composite coatings have proved to constitute interesting and successful platforms for the conception of solid and biocompatible biomaterials inducing the osseous regeneration processes (hydroxyapatite growth, osteoblasts attachment). This paper describes an original strategy for the conception of resistant and homogeneous tantalum oxide/carbon nanotubes layers on titanium through the introduction of carbon nanotubes functionalized by phosphonic acid moieties (-P(=O)(OH)2). Strong covalent C-P bonds are specifically inserted on their external sidewalls with a ratio of two phosphonic groups per anchoring point. Experimental results highlight the stronger "tantalum capture agent" effect of phosphonic-modified nanotubes during the sol-gel formation process of the deposits compared to nanotubes bearing oxidized functions (-OH, -C=O, -C(=O)OH). Particular attention is also paid to the relative impact of the rate of functionalization and the dispersion degree of the carbon nanotubes in the coatings, as well as their wrapping level by the tantalum oxide matrix material. The resulting effect on the in vitro growth of hydroxyapatite is also evaluated to confirm the primary osseous bioactivity of those materials. Chemical, structural and morphological features of the different composite deposits described herein are assessed by X-ray photoelectron spectroscopy (XPS), scanning (SEM) and transmission (TEM) electronic microscopies, energy dispersive X-rays analysis (EDX) and peeling tests.

  6. Dissolution kinetics of small amounts of oxygen in tantalum alloy T-111 and internal oxide displacement reactions during annealing

    Science.gov (United States)

    Stecura, S.

    1976-01-01

    Oxygen was added to T-111 (Ta-8W-2Hf, wt. %) at 820 and 990 C at an oxygen pressure of about 0.0003 torr. The technique employed permitted predetermined and reproducible doping of T-111 up to 3.0 at. % oxygen. Based on the temperature dependence of the doping reaction, it is concluded that the initial rates of oxygen pickup are probably controlled by solution of oxygen into the T-111 lattice. Although hafnium oxides are more stable than those of tantalum or tungsten, analyses of extracted residues indicate that the latter oxides predominate in the as-doped specimens, presumably because of the higher concentrations of tantalum and tungsten in the alloy. However, high-temperature annealing promotes gettering of dissolved oxygen and of other oxides to form hafnium oxides. Small amounts of tantalum and tungsten oxides were still present after high-temperature annealing. Tungsten oxide (WO3) volatilizes slightly from the surface of T-111 at 990 C. The vaporization of WO3 has no apparent affect on the doping reaction.

  7. The effect of yttrium addition on oxidation of a sputtered nanocrystalline coating with moderate amount of tantalum in composition

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Jinlong [Corrosion and Protection Laboratory, Key Laboratory of Superlight Materials and Surface Technology (Harbin Engineering University), Ministry of Education, Harbin 150001 (China); Laboratory of Corrosion and Protection, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China); Chen, Minghui, E-mail: mhchen@imr.ac.cn [Laboratory of Corrosion and Protection, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China); Yang, Lanlan; Liu, Li; Zhu, Shenglong [Laboratory of Corrosion and Protection, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China); Wang, Fuhui [Corrosion and Protection Laboratory, Key Laboratory of Superlight Materials and Surface Technology (Harbin Engineering University), Ministry of Education, Harbin 150001 (China); Laboratory of Corrosion and Protection, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China); Meng, Guozhe [Corrosion and Protection Laboratory, Key Laboratory of Superlight Materials and Surface Technology (Harbin Engineering University), Ministry of Education, Harbin 150001 (China)

    2016-03-15

    Graphical abstract: - Highlights: • Effect of Y addition on oxidation of nanocrystalline coating is studied. • Y addition delays transformation of q-Al{sub 2}O{sub 3} to a-Al{sub 2}O{sub 3} during oxidation. • Y addition prevents scale rumpling. • Y segregates at grain boundaries of the nanocrystalline coating. • Y retards the transportation of Ta thus reduces its oxidation. - Abstract: The effect of yttrium addition on isothermal oxidation at 1050 °C of a sputtered nanocrystalline coating with moderate amount of tantalum in composition was investigated. Results indicate that yttrium addition delays transformation of metastable θ-Al{sub 2}O{sub 3} to equilibrium α-Al{sub 2}O{sub 3} grown on the nanocrystalline coatings. It prevents scale rumpling and promotes the formation of oxide pegs at interface between the oxide scale and the underlying coating. Besides, yttrium prefers to segregate at grain boundaries of the nanocrystalline coating and retards the outward transportation of tantalum from coating to oxide scale, thus reducing the excessive oxidation of tantalum.

  8. Multifunctional hybrid coating on titanium towards hydroxyapatite growth: Electrodeposition of tantalum and its molecular functionalization with organophosphonic acids films

    Energy Technology Data Exchange (ETDEWEB)

    Arnould, Christelle; Delhalle, Joseph [Laboratory of Chemistry and Electrochemistry of Surfaces, University of Namur (FUNDP), Rue de Bruxelles 61, B-5000 Namur (Belgium); Mekhalif, Zineb [Laboratory of Chemistry and Electrochemistry of Surfaces, University of Namur (FUNDP), Rue de Bruxelles 61, B-5000 Namur (Belgium)], E-mail: zineb.mekhalif@fundp.ac.be

    2008-07-20

    Titanium and its alloys are base materials used in the dental and orthopaedic fields owing to suitable intrinsic properties: good biocompatibility, high corrosion resistance and excellent mechanical properties. However, the bonding between titanium and bone tissue is not always strong enough and can become a critical problem. In this context, the two main objectives of this paper are the increase of the corrosion resistance and the improvement of the hydroxyapatite (HAp) growth. The surface modification considered here is achieved in three main steps and consists in the elaboration of different inorganic and organic coatings. The first step is the elaboration of electrodeposition of tantalum on the titanium oxide film of a titanium substrate. The second step is the modification of the tantalum oxide coating with organophosphonic acids. The last step is the nucleation and growth of HAP on the outermost layer of the system by immersion in a simulated body fluid. The hybrid coating tantalum oxide/organophosphonic acids/molecular layer is shown to be promising for orthopaedic implants.

  9. Selective extraction of tantalum fluoride in polyurethane foam; Sorcao seletiva de fluoreto de tantalo em espuma de poliuretano

    Energy Technology Data Exchange (ETDEWEB)

    Ferreira, Elizabeth de M. Massena; Schwamback, Niomedes; Mantovano, Jose Luiz; Carvalho, Marcelo S. de [Instituto de Engenharia Nuclear (IEN), Rio de Janeiro, RJ (Brazil)

    2000-07-01

    The physico-chemical parameters for tantalum fluoride extraction on polyether polyurethane foam (PUF) were investigated focusing on its selective separation from sample matrices of fluoro complexes metals and direct determination on ground PUF by X-ray fluorescence (dispersive wavelength). Tantalum was quantitatively recovered from 0,5 mol/L hydrofluoric acid solution, after 40 minutes mechanical shaking, using batch procedure and 0,1 g PUF. The system allows the presence of sulfuric acid until 2,0 mol/L, shows distribution ratio (D) of about 3,2.10{sup 3}(L/Kg) and sorption capacity of 3,0 g Ta/ Kg EPU. At the optimized conditions analytical curve is linear up to 100{mu}g Ta; sample dilution until 0,3 L makes possible the metal determination with detection (3{sigma}) and quantification (10{sigma}) limits of 3 and 16 ppb, respectively. Ratios of 1:1000 tantalum to niobium, zirconium, uranium, tungsten, tin, iron, aluminium and manganese does not interfere. (author)

  10. A He-gas Cooled, Stationary Granular Target

    CERN Document Server

    Pugnat, P

    2003-01-01

    In the CERN approach to the design of a neutrino factory, the repetition frequency of the proton beam is high enough to consider stationary solid targets as a viable solution for multi-MW beams. The target consists of high density tantalum spheres of 2 mm diameter which can efficiently be cooled by passing a high mass flow He-gas stream through the voids between the Ta-granules. Very small thermal shocks and stresses will arise in this fine grained structure due to the relatively long burst of 3.3 ms from the SPL-proton linac. In a quadruple target system where each target receives only one quarter of the total beam power of 4 MW, conservative temperature levels and adequate lifetimes of the target are estimated in its very high radiation environment. A conceptual design of the integration of the target into the magnetic horn-pion-collector is presented.

  11. Fabrication of anodized tantalum oxide integrated capacitors on singulated chips with active devices

    Science.gov (United States)

    Wasef, Mohammed Aziz

    The purpose of this project was to determine the feasibility and processability of fabricating anodized tantalum oxide integrated capacitors on singulated chips. Using high-resolution transparencies to pattern the metals during the photolithographic process, capacitors as large as 0.25 cm2 were fabricated successfully with the yield being higher for capacitors smaller than 0.1 cm2. Several capacitor designed were attempted and final designed was selected on the basis of ease of alignment and prevention of shorts. The next step in the project involved utilizing this design to fabricate capacitors on 2.2 mm by 2.2 mm silicon dummy chips. In order to accomplish this task, a support wafer technique was used. A silicon wafer with holes etched all the way through was attached to a non-etched silicon wafer to provide a base for the dummy chips that were placed in the holes of the support wafer, thus making the top of the chips co-planar with a wafer that could be put through standard wafer processing equipment. The chips were glued to the wafer using a thermoplastic as an adhesive. The design specified for this project called for five 100 pF capacitors and a single 50 pF capacitor. Since the chips had to be individually placed in the holes, all the masks used in the project had to be individually designed for reach run. The capacitors had a bottom plate thickness of 2500 A of tantalum which was anodized at 120 V and 0.5 mA/cm2 to an oxide thickness of 1920 A. The top plate was 2 mum of aluminum and the insulating ring around the bottom plate was made of 5 mum of benzocyclobutene. After fabrication, testing of the capacitors provided a yield of 97% for the 100 pF capacitors with average capacitance of 98.3 pF +/- 3.6 pF and 75% for the 50 pF capacitors with an average capacitance of 50 pF +/- 1.65 pF. The inductance of the capacitors was less than 20 pH and resistance was about 110 O. The resistance was brought down to 1 O when a 2 mum sublayer of aluminum was deposited

  12. 3 MW solid rotating target design

    Science.gov (United States)

    McManamy, T.; Rennich, M.; Gallmeier, F.; Ferguson, P.; Janney, J.

    2010-03-01

    A rotating solid target design concept is being developed for potential use at the second SNS target station (STS). A long pulse beam (˜1 ms) at 1.3 GeV and 20 Hz is planned with power levels at or above 1 MW. Since the long pulse may give future opportunities for higher power, this study is looking at 3 MW to compare the performance of a solid rotating target to a mercury target. Unlike the case for stationary solid targets at such powers this study indicates that a rotating solid target, when used with large coupled hydrogen moderators, has neutronic performance equal to or better than that with a mercury target, and the solid target has a greatly increased lifetime. Design studies have investigated water cooled tungsten targets with tantalum cladding approximately 1.2 m in diameter, and 70 mm thick. Operating temperatures are low (plane, top and bottom surface cooling. In case of cooling system failure, the diameter gives enough surface area to remove the decay heat by radiation to the surrounding reflector assemblies while keeping the peak temperatures below approximately 700 °C. This temperature should mitigate potential loss of coolant accidents and subsequent steam, tungsten interaction which has a threshold of approximately 800 °C. Design layouts for the sealing systems and potential target station concepts have been developed.

  13. Tantalum (oxy)nitrides: Preparation, characterisation and enhancement of photo-Fenton-like degradation of atrazine under visible light

    Energy Technology Data Exchange (ETDEWEB)

    Du, Yingxun, E-mail: yxdu@niglas.ac.cn [Nanjing Institute of Geography and Limnology, State Key Laboratory of Lake Science and Environment, Chinese Academy of Sciences, Nanjing 210008 (China); Zhao, Lu; Su, Yaling [Nanjing Institute of Geography and Limnology, State Key Laboratory of Lake Science and Environment, Chinese Academy of Sciences, Nanjing 210008 (China)

    2011-11-15

    Highlights: {yields} The photocatalytic activity of TaON for Fe{sup 3+} reduction is higher than that of Ta{sub 3}N{sub 5}. {yields} Atrazine degradation was accelerated significantly by tantalum (oxy)nitrides sample. {yields} The regenerated catalyst displays considerably stable performance for atrazine degradation. - Abstract: Tantalum (oxy)nitrides were prepared by the nitridation of Ta{sub 2}O{sub 5} and were added to a photo-Fenton-like system to enhance Fe{sup 3+} reduction and atrazine degradation under visible light. The samples were characterized by XRD, XPS, DRS and BET analyses. XPS analysis showed that the nitrogen content of the tantalum (oxy)nitride samples increased noticeably with the nitridation temperature and nitridation time but slightly with the flow rate of NH{sub 3}. XRD results showed Ta{sub 2}O{sub 5} was first converted to TaON and then to Ta{sub 3}N{sub 5} when the nitridation temperature increased. DRS analysis showed that the sample obtained at 800 {sup o}C displayed the strongest absorption of visible light. However, the ability of the tantalum (oxy)nitrides to reduce Fe{sup 3+} did not increase continuously with the nitrogen content. Sample 7 (700 {sup o}C, Q{sub NH{sub 3}}=0.3L/min, 6 h) showed the highest level of photocatalytic activity for Fe{sup 3+} reduction. This is because the photocatalytic activity of TaON for Fe{sup 3+} reduction is higher than that of Ta{sub 3}N{sub 5}. And a slight synergetic effect was observed between TaON and Ta{sub 3}N{sub 5}. With the addition of sample 7, H{sub 2}O{sub 2} decomposition and atrazine degradation were significantly accelerated in a photo-Fenton-like system under visible light. The regenerated tantalum (oxy)nitrides catalyst displayed considerably stable performance for atrazine degradation.

  14. An experimental study of the solubility and speciation of tantalum in fluoride-bearing aqueous solutions at elevated temperature

    Science.gov (United States)

    Timofeev, A.; Migdisov, Art. A.; Williams-Jones, A. E.

    2017-01-01

    The solubility of Ta2O5 (solid) and the speciation of tantalum in HF-bearing aqueous solutions have been determined at temperatures of 100-250 °C and vapour-saturated water pressure. Tantalum is transported as the species Ta(OH)50 at low HF concentration and pH ∼1-3. At higher HF concentration, tantalum mobility is controlled by the species TaF3(OH)3- and TaF50; the presence of TaF50 is only evident at ⩽150 °C. Equilibrium constants range from -17.4 ± 0.45 to -16.4 ± 0.12 for the formation of Ta(OH)50 from crystalline Ta2O5 and from -8.24 ± 0.64 to -8.55 ± 0.68 for the formation of TaF3(OH)3- at 100 and 250 °C, respectively. For TaF50, they were determined to be 0.13 at 100 °C and -0.35 at 150 °C. In many respects, the behaviour of tantalum in acidic fluoride-bearing solutions is similar to that of niobium. The solubility of Ta2O5 (solid) is not dependent on HF concentration in fluoride-poor fluids, but rises rapidly at higher HF concentration. However, at the conditions of our experiments, namely a pH of ∼2, temperature up to 250 °C, and a wide range of HF concentrations, Ta2O5 (solid) solubility is almost invariably lower than that of Nb2O5 (solid). Modelling of Nb and Ta leaching confirmed the preferential mobility of niobium under most conditions expected in natural fluoride-rich hydrothermal systems. This modelling also demonstrated that both niobium and tantalum are rapidly deposited upon removal of fluoride from an acidic brine. As a result of hydrothermal alteration, the Nb/Ta ratios of secondary minerals may increase relative to those of the primary mineral, or remain largely unaffected, depending on the pH of the fluid.

  15. Dose measurement for systemic irradiation with a moving table specially designed for total body irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Oda, Makoto; Oida, Masatada; Nagumo, Junya; Fujita, Katsuhisa; Furuya, Teruo; Watanabe, Yoshiharu [Hokkaido Univ., Sapporo (Japan). Hospital

    2001-07-01

    Total body irradiation (TBI) is performed in combination with chemotherapy to kill malignant tumor cells in the body prior to bone marrow transplantation. This study reports the results of dose measurements required for clinical application of the moving table technique to TBI. Since irradiation is performed as the table moves, the authors gathered sufficient basic data for irradiation by measuring output dose, tissue peak dose ratio (TPR), and the relationship between dose rate and movement velocity. The output doses were varied according to dose rate, movement velocity, radiation field, and source-target distance (STD) under these conditions. The authors measured the relationship between the dose rate and the movement velocity with the irradiation field and STD set to fit clinical applications. TPR during irradiation while moving differs from TPR during stationary irradiation, and it was measured according to the method of irradiation. The effect of body thickness was easily corrected by changing the movement velocity during the measurements. The authors measured the dose with a thermoluminescent dosimeter (TLD) during clinical application and confirmed the accuracy of the measurements. TBI with the moving table, it makes possible to perform bilateral irradiation in both posterior-anterior and anterior-posterior directions with the patient in the supine position, to reduce treatment time, to shield the lung well with reproducibility of posture, and to treat with high accuracy. (K.H.)

  16. Determination of niobium, tantalum, and uranium in tantalite-columbite ores by X-ray fluorescence spectrometry; Application de la spectrometrie de fluorescence de rayos X a la determination de niobium, tantale et uranium dans niobiotantalites

    Energy Technology Data Exchange (ETDEWEB)

    Latorre, O.; Bermudez Polonio, J.

    1964-07-01

    A simple and quick procedure is carried out to determine niobium, tantalum and uranium employing the internal standard technique; zinc as internal standard for tantalum and molybdenum for niobium and uranium were selected. Some inter element effects were studied and the ratios. (Author)

  17. Neutronic and thermal-hydraulic analysis of a device for irradiation of LEU UAl{sub x}-Al targets for {sup 99}Mo production in the IEA-R1 reactor; Analises neutronica e termo-hidraulica de um dispositivo para irradiacao de alvos tipo LEU de UAl{sub x}-Al para producao de {sup 99}MO no reator IEA-R1

    Energy Technology Data Exchange (ETDEWEB)

    Nishiyama, Pedro Julio Batista de Oliveira

    2012-07-01

    Technetium-99m ({sup 99m}Tc), the product of radioactive decay of molybdenum-99 ( Mo), is one of the most widely used radioisotope in nuclear medicine, covering approximately 80% of all radiodiagnosis procedures in the world. Nowadays, Brazil requires an amount of about 450 Ci of {sup 99}Mo per week. Due to the crisis and the shortage of {sup 99}Mo supply chain that has been observed on the world since 2008, IPEN/CNEN-SP decided to develop a project to produce {sup 99}Mo through fission of uranium-235. The objective of this dissertation was the development of neutronic and thermal-hydraulic calculations to evaluate the operational safety of a device for {sup 99}Mo production to be irradiated in the IEA-Rl reactor core at 5 MW. In this device will be placed ten targets of UAl{sub x}-Al dispersion fuel with low enriched uranium (LEU) and density of 2.889 gU/cm{sup 3}. For the neutronic calculations were utilized the computer codes HAMMER-TECHNION and CITATION and the maximum temperatures reached in the targets were calculated with the code MTRCR-IEA-R1. The analysis demonstrated that the device irradiation will occur without adverse consequences to the operation of the reactor. The total amount of {sup 99}Mo was calculated with the program SCALE and considering that the time needed for the chemical processing and recovering of the {sup 99}Mo will be five days after the irradiation, we have that the {sup 99}Mo activity available for distribution will be 176 Ci for 3 days of irradiation, 236 Ci for 5 days of irradiation and 272 Ci for 7 days of targets irradiation. (author)'.

  18. The impact of substrate properties and thermal annealing on tantalum nitride thin films

    Energy Technology Data Exchange (ETDEWEB)

    Grosser, M., E-mail: michaela_grosser@yahoo.de [Chair of Micromechanics, Microfluidics/Microactuators, Saarland University, 66123 Saarbruecken (Germany); Muench, M.; Seidel, H. [Chair of Micromechanics, Microfluidics/Microactuators, Saarland University, 66123 Saarbruecken (Germany); Bienert, C.; Roosen, A. [Friedrich-Alexander-University Erlangen-Nuremberg, Martensstr. 5, D-91058 Erlangen (Germany); Schmid, U. [Department for Microsystems Technology, Institute of Sensor and Actuator Systems, Vienna University of Technology, Floragasse 7, 1040 Vienna (Austria)

    2012-01-15

    In this study film properties of sputter-deposited tantalum nitride (TaN{sub x}) thin layers are investigated focusing on the impact of substrate properties, varying nitrogen content for film synthetization as well as post-deposition annealings in the temperature range up to 500 Degree-Sign C. For comparison, these investigations are done on low temperature co-fired ceramics and on silicon based substrates whereas the latter approach ensures defined and well-known surface properties. Furthermore, results on the phase evolution with high temperature annealings are presented showing a transformation of Ta{sub 4}N to Ta{sub 2}N in the temperature range between 350 Degree-Sign C and 500 Degree-Sign C. With increasing nitrogen content (i.e. nitrogen flow during film deposition) in the TaN{sub x} layers the topography shows first an increase in surface roughness, next a range where a smoothing of the surface characteristics is observed, and finally buckling and the existence of grain agglomerates. All these analyses are further evaluated with electrical measurements on the film resistivity and on the oxidation behaviour to gain deeper insight into material parameters relevant for micromachined devices which are operated under harsh environmental conditions.

  19. Functional and structural fatigue of titanium tantalum high temperature shape memory alloys (HT SMAs)

    Energy Technology Data Exchange (ETDEWEB)

    Niendorf, T., E-mail: Thomas.Niendorf@iwt.tu-freiberg.de [Institute of Materials Engineering, Technische Universität Bergakademie Freiberg, 09599 Freiberg (Germany); Krooß, P. [Lehrstuhl für Werkstoffkunde (Materials Science), University of Paderborn, 33098 Paderborn (Germany); Batyrsina, E. [Institut für Werkstoffkunde (Materials Science), Leibniz Universität Hannover, 30823 Garbsen (Germany); Paulsen, A.; Motemani, Y.; Ludwig, A.; Buenconsejo, P.; Frenzel, J.; Eggeler, G. [Institut für Werkstoffe, Ruhr-Universität Bochum, 44801 Bochum (Germany); Maier, H.J. [Institut für Werkstoffkunde (Materials Science), Leibniz Universität Hannover, 30823 Garbsen (Germany)

    2015-01-03

    Due to their high work output and good mechanical properties, actuators made from shape memory alloys (SMAs) are used in numerous applications. Unfortunately, SMAs such as nickel–titanium (Ni–Ti) can only be employed at temperatures up to about 100 °C. Lately, high-temperature shape memory alloys (HT SMAs) have been introduced to overcome this limitation. Ternary systems based on Ni–Ti have been intensively characterized and alloys are available that can operate at elevated temperatures. However, these alloys either contain substantial amounts of expensive noble elements like platinum and palladium, or the materials are brittle. The titanium–tantalum (Ti–Ta) system has been developed to overcome these issues. Binary Ti–Ta provides relatively high M{sub S} temperature combined with excellent workability, but it suffers from fast cyclic degradation. By alloying with third elements this drawback can be overcome: The ternary Ti–Ta–Al alloy shows overall promising properties as will be shown in the present work. In-situ thermo-mechanical cycling experiments were conducted and allowed for evaluation of the factors affecting the functional and structural fatigue of this alloy. Functional fatigue is dominated by ω-phase evolution, while structural fatigue is triggered by an interplay of ω-phase induced embrittlement and deformation constraints imposed by unsuitable texture. In addition, a concept for fatigue life extension proposed very recently for binary Ti–Ta, is demonstrated to be also applicable for the ternary Ti–Ta–Al.

  20. Bounds on the Rate Dependent Plastic Flow of Tantalum up to 75 GPa

    Science.gov (United States)

    Reed, Bryan; Patterson, Reed; Kumar, Mukul

    2013-06-01

    We report improvements in a general thermodynamics-based velocimetry analysis method designed to extract strength and plastic-flow information from shock and ramp compression experiments. The method allows extraction of thermodynamic histories, including deviatoric stress and plastic strain, including nonsteady rate-dependent features. The improved method includes free-surface corrections for pullback waves, reduced noise sensitivity, and application to pressures of 75 GPa and higher. Specifically, we show results for shock waves in tantalum, including bounds on the plastic flow behavior at strain rates exceeding 1e7/s.The deviatoric stress appears to be almost entirely dependent on strain rate, with very little pressure dependence.The deviatoric stress in the post-shock plateau state appears to be very small at higher pressures, calling into question the value of considering strength as a steady- state pressure-dependent quantity. This work performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.