WorldWideScience

Sample records for ion irradiation enhancement

  1. Enhanced biocompatibility of PDMS (polydimethylsiloxane) polymer films by ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Ionescu, M., E-mail: Mihail.Ionescu@ansto.gov.au [Australian Nuclear Science and Technology Organization, Sydney (Australia); Winton, B.; Wexler, D. [Faculty of Engineering, University of Wollongong, Wollongong (Australia); Siegele, R.; Deslantes, A.; Stelcer, E.; Atanacio, A.; Cohen, D.D. [Australian Nuclear Science and Technology Organization, Sydney (Australia)

    2012-02-15

    PDMS films several microns thick deposited on polished Si wafers were irradiated with Mg, Ta, and Fe in the low energy range of 40 keV to 200 keV, and for doses of 10{sup 16}-10{sup 18} ions/cm{sup 2}. After irradiation the films surface is self-organised into 3D coherent and semi-coherent domains. As a consequence of the surface irradiation conditions and the surface boundary conditions, some domains are highly ordered in the form of parallel waves of approximately 1 {mu}m in height, or the result can be semi-ordered regions or disordered regions. In addition, the surface energy of the irradiated polymer is increasing, as reflected in the decrease in its surface hydrophobicity, which is beneficial for cell adhesion. The irradiated samples were tested in vivo, and the results show an increase in viable cell count of up to 650%.

  2. Enhancement of Ammonia Sensitivity in Swift Heavy Ion Irradiated Nanocrystalline SnO2 Thin Films

    Directory of Open Access Journals (Sweden)

    Sanju Rani

    2008-01-01

    Full Text Available Swift heavy ion irradiation is an effective technique to induce changes in the microstructure and electronic energy levels of materials leading to significant modification of properties. Here we report enhancement of ammonia (NH3 sensitivity of SnO2 thin films subjected to high-energy Ni+ ion irradiation. Sol-gel-derived SnO2 thin films (100 nm thickness were exposed to 75 MeV Ni+ ion irradiation, and the gas response characteristics of irradiated films were studied as a function of ion fluence. The irradiated films showed p-type conductivity with a much higher response to NH3 compared to other gases such as ethanol. The observed enhancement of NH3 sensitivity is discussed in context of ion beam generated electronic states in the SnO2 thin films.

  3. Ion irradiation induced enhancement of out-of-plane magnetic anisotropy in ultrathin Co films

    Energy Technology Data Exchange (ETDEWEB)

    Mazalski, P.; Kurant, Z.; Maziewski, A. [Faculty of Physics, University of Bialystok, Bialystok (Poland); Liedke, M. O.; Fassbender, J. [Helmholtz-Zentrum Dresden-Rossendorf, Dresden (Germany); Baczewski, L. T.; Wawro, A. [Institute of Physics, Polish Academy of Science, Warszawa (Poland)

    2013-05-07

    Ga{sup +} or He{sup +} irradiated MBE grown ultrathin films of sapphire/Pt/Co(d{sub Co})/Pt(d{sub Pt}) were studied using polar Kerr effect in wide ranges of both cobalt d{sub Co} and platinum d{sub Pt} thicknesses as well as ion fluences F. Two branches of increased magnetic anisotropy and enhanced Kerr rotation angle induced by Ga{sup +} or He{sup +} irradiation are clearly visible in two-dimensional (d{sub Co}, LogF) diagrams. Only Ga{sup +} irradiation induces two branches of out-of-plane magnetization state.

  4. Enhanced electron field emission from carbon nanotubes irradiated by energetic C ions.

    Science.gov (United States)

    Sun, Peng-Cheng; Deng, Jian-Hua; Cheng, Guo-An; Zheng, Rui-Ting; Ping, Zhao-Xia

    2012-08-01

    The field emission performance and structure of the vertically aligned multi-walled carbon nanotube arrays irradiated by energetic C ion with average energy of 40 keV have been investigated. During energetic C ion irradiation, the curves of emission current density versus the applied field of samples shift firstly to low applied fields when the irradiation doses are less than 9.6 x 10(16) cm(-2), and further increase of dose makes the curves reversing to a high applied field, which shows that high dose irradiation in carbon nanotube arrays makes their field emission performance worse. After energetic ion irradiation with a dose of 9.6 x 1016 cm(-2), the turn-on electric field and the threshold electric field of samples decreased from 0.80 and 1.13 V/microm to 0.67 and 0.98 V/microm respectively. Structural analysis of scanning electron microscopy, transmission electron microscopy and Raman spectroscopy indicates that the amorphous carbon nanowire/carbon nanotube hetero nano-structures have been fabricated in the C ion irradiated carbon nanotubes. The enhancement of electron field emission is due to the formation of amorphous carbon nanowires at the tip of carbon nanotube arrays, which is an electron emitting material with low work function.

  5. Layer compression and enhanced optical properties of few-layer graphene nanosheets induced by ion irradiation

    CERN Document Server

    Tan, Yang; Akhmadaliev, Shavkat; Zhou, Shengqiang; Chen, Feng

    2016-01-01

    Graphene has been recognized as an attractive two-dimensional material for fundamental research and wide applications in electronic and photonic devices owing to its unique properties. The technologies to modulate the properties of graphene are of continuous interest to researchers in multidisciplinary areas. Herein, we report on the first experimental observation of the layer-to-layer compression and enhanced optical properties of few-layer graphene nanosheets by applying the irradiation of energetic ion beams. After the irradiation, the space between the graphene layers was reduced, resulting in a tighter contact between the few-layer graphene nanosheet and the surface of the substrate. This processing also enhanced the interaction between the graphene nanosheets and the evanescent-field wave near the surface, thus reinforcing the polarization-dependent light absorption of the graphene layers (with 3-fold polarization extinction ratio increment). Utilizing the ion-irradiated graphene nanosheets as saturable...

  6. POLYMERS CONTAINING Cu NANOPARTICLES IRRADIATED BY LASER TO ENHANCE THE ION ACCELERATION

    Directory of Open Access Journals (Sweden)

    Mariapompea Cutroneo

    2015-06-01

    Full Text Available Target Normal Sheath Acceleration method was employed at PALS to accelerate ions from laser-generated plasma at intensities above 1015 W/cm2. Laser parameters, irradiation conditions and target geometry and composition control the plasma properties and the electric field driving the ion acceleration. Cu nanoparticles deposited on the polymer promote resonant absorption effects increasing the plasma electron density and enhancing the proton acceleration. Protons can be accelerated in forward direction at kinetic energies up to about 3.5 MeV. The optimal target thickness, the maximum acceleration energy and the angular distribution of emitted particles have been measured using ion collectors, X-ray CCD streak camera, SiC detectors and Thomson Parabola Spectrometer.

  7. Formation of nanodots and enhancement of thermoelectric power induced by ion irradiation in PbTe:Ag composite thin films

    Energy Technology Data Exchange (ETDEWEB)

    Bala, Manju, E-mail: manjubala474@gmail.com [Inter-University Accelerator Centre, Aruna Asaf Ali Marg, New Delhi 110067 (India); Meena, Ramcharan; Gupta, Srashti; Pannu, Compesh [Inter-University Accelerator Centre, Aruna Asaf Ali Marg, New Delhi 110067 (India); Tripathi, Tripurari S. [Aalto University, Värmemansgränden 2, 02150 Espoo (Finland); Varma, Shikha [Institute of Physics, Bhubaneshwar, Odisha 751005 (India); Tripathi, Surya K. [Department of Physics, Panjab University, Chandigarh 160 014 (India); Asokan, K., E-mail: asokaniuac@gmail.com [Inter-University Accelerator Centre, Aruna Asaf Ali Marg, New Delhi 110067 (India); Avasthi, Devesh K. [Amity University, Noida 201313, Uttar Pradesh (India)

    2016-07-15

    Present study demonstrates an enhancement in thermoelectric power of 10% Ag doped PbTe (PbTe:Ag) thin films when irradiated with 200 keV Ar ion. X-ray diffraction showed an increase in crystallinity for both PbTe and PbTe:10Ag nano-composite films after Ar ion irradiation due to annealing of defects in the grain boundaries. The preferential sputtering of Pb and Te ions in comparison to Ag ions resulted in the formation of nano-dots. This was further confirmed by X-ray photoelectron spectroscopy (XPS). Such an enhancement in thermoelectric power of irradiated PbTe:10Ag films in comparison to pristine PbTe:10Ag film is attributed to the decrease in charge carrier concentration that takes part in the transport process via restricting the tunneling of carriers through the wider potential barrier formed at the interface of nano-dots.

  8. Cladding-like waveguide structure in Nd:YAG crystal fabricated by multiple ion irradiation for enhanced waveguide lasing.

    Science.gov (United States)

    Shang, Zhen; Tan, Yang; Akhmadaliev, Shavkat; Zhou, Shengqiang; Chen, Feng

    2015-10-19

    We report on a cladding-like waveguide structure in Nd:YAG crystal fabricated by the multiple carbon ion beam irradiation. After the designed multiple irradiation process, the cladding-like waveguide with triple refractive-index layers were constructed in the region near the surface of the crystal. With such a structure, the waveguiding core was compressed and refractive index profile was modified, resulting in a higher light intensity than that of the single ion-beam-irradiated monolayer waveguide. The waveguide lasing at wavelength of 1064 nm was achieved with enhanced performance in the cladding-like structures with both planar and ridge configurations by the optical pump at 810 nm.

  9. Preparation of thermal resistant-enhanced separators for lithium ion battery by electron beam irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Sohn, Joon Yong; Shin, Junhwa; Nho, Youngchang [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2012-03-15

    Micro-porous membrane made of polyethylene (PE) or polypropylene (PP) is most widely used as physical separators between the cathode and anode in lithium secondary batteries. However, the polymer membranes so soften or melt when the temperature reaches 130 .deg. C or higher because of thermal shrinkage of the polyolefin separators, and thaw low thermal stability may cause internal short circuiting or lead to thermal runaway. In this study, to realize a highly safe battery, we prepared three type separators as crosslinked PE separator, polymer-coated PE separator, and ceramic-coated PE separators, for lithium secondary battery by electron beam irradiation. We prepared crosslinked PE separators with the improved thermal stability by irradiating a commercial PE separator with an electron beam. A polymer-coated PE separator was prepared by a dip-coating of PVDF-HFP/PEGDMA on both sides of a PE separator followed by an electron beam irradiation. Ceramic-coated PE separator was prepared by coating ceramic particles on a PE separator followed by an electron beam irradiation. The prepared separators were characterized with FT-IR, SEM, electrolyte uptake, ion conductivity, thermal shrinkage and battery performance test.

  10. In situ heavy ion irradiation studies of nanopore shrinkage and enhanced radiation tolerance of nanoporous Au

    Science.gov (United States)

    Li, Jin; Fan, C.; Ding, J.; Xue, S.; Chen, Y.; Li, Q.; Wang, H.; Zhang, X.

    2017-01-01

    High energy particle radiations induce severe microstructural damage in metallic materials. Nanoporous materials with a giant surface-to-volume ratio may alleviate radiation damage in irradiated metallic materials as free surface are defect sinks. Here we show, by using in situ Kr ion irradiation in a transmission electron microscope at room temperature, that nanoporous Au indeed has significantly improved radiation tolerance comparing with coarse-grained, fully dense Au. In situ studies show that nanopores can absorb and eliminate a large number of radiation-induced defect clusters. Meanwhile, nanopores shrink (self-heal) during radiation, and their shrinkage rate is pore size dependent. Furthermore, the in situ studies show dose-rate-dependent diffusivity of defect clusters. This study sheds light on the design of radiation-tolerant nanoporous metallic materials for advanced nuclear reactor applications.

  11. Enhancement in field emission current density of Ni nanoparticles embedded in thin silica matrix by swift heavy ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Sarker, Debalaya; Patra, Rajkumar; Srivastava, P.; Ghosh, S., E-mail: santanu1@physics.iitd.ac.in [Nanostech Laboratory, Department of Physics, Indian Institute of Technology Delhi, New Delhi 110016 (India); Kumar, H. [Nanostech Laboratory, Department of Physics, Indian Institute of Technology Delhi, New Delhi 110016 (India); Instituto de Física, Universidade de São Paulo, USP, 05508-090 São Paulo, SP (Brazil); Kabiraj, D.; Avasthi, D. K. [Inter University Accelerator Centre, New Delhi 110067 (India); Vayalil, Sarathlal K.; Roth, S. V. [DESY, Petra III, Hamburg (Germany)

    2014-05-07

    The field emission (FE) properties of nickel nanoparticles embedded in thin silica matrix irradiated with 100 MeV Au{sup +7} ions at various fluences are studied here. A large increase in FE current density is observed in the irradiated films as compared to their as deposited counterpart. The dependence of FE properties on irradiation fluence is correlated with surface roughness, density of states of valence band and size distribution of nanoparticles as examined with atomic force microscope, X-ray photoelectron spectroscopy, and grazing incidence small angle x-ray scattering. A current density as high as 0.48 mA/cm{sup 2} at an applied field 15 V/μm has been found for the first time for planar field emitters in the film irradiated with fluence of 5.0 × 10{sup 13} ions/cm{sup 2}. This significant enhancement in the current density is attributed to an optimized size distribution along with highest surface roughness of the same. This new member of field emission family meets most of the requirements of cold cathodes for vacuum micro/nanoelectronic devices.

  12. Enhancement of wettability and antibiotic loading/release of hydroxyapatite thin film modified by 100 MeV Ag{sup 7+} ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Elayaraja, K. [Crystal Growth Centre, Anna University, Chennai 600 025 (India); Rajesh, P. [Biomedical Technology Wing, Sree Chitra Tirunal Institute for Medical Sciences and Technology, Poojappura, Thiruvananthapuram 695 012 (India); Ahymah Joshy, M.I.; Sarath Chandra, V.; Suganthi, R.V. [Crystal Growth Centre, Anna University, Chennai 600 025 (India); Kennedy, J. [National Isotope Centre, GNS Science, 30 Gracefield Road, Lower Hutt (New Zealand); Kulriya, P.K.; Sulania, I.; Asokan, K.; Kanjilal, D.; Avasthi, D.K. [Inter-University Accelerator Centre, Aruna Asaf Ali Marg, New Delhi 110 067 (India); Varma, H.K. [Biomedical Technology Wing, Sree Chitra Tirunal Institute for Medical Sciences and Technology, Poojappura, Thiruvananthapuram 695 012 (India); Narayana Kalkura, S., E-mail: kalkurasn@annauniv.edu [Crystal Growth Centre, Anna University, Chennai 600 025 (India)

    2012-05-15

    Highlights: Black-Right-Pointing-Pointer Reduction in particle size on irradiation leading to nanosized HAp. Black-Right-Pointing-Pointer Enhancement of surface roughness and bioactivity on irradiation. Black-Right-Pointing-Pointer Irradiation at lower fluence transforms the surface hydrophobic. Black-Right-Pointing-Pointer The surface turned hydrophilic at higher fluence. Black-Right-Pointing-Pointer Improved drug (amoxicillin) loading on irradiated samples. - Abstract: The effect of swift heavy 100 MeV Ag{sup 7+} ions irradiation was studied on hydroxyapatite (HAp) thin film prepared by pulsed laser deposition technique (PLD). The GIXRD analysis confirmed the absence of any phase in the HAp phase due to irradiation. In addition, there was a considerable decrease in crystallinity and crystallite size on irradiation. There was no significant variation in the stoichiometry of the irradiated films. Irradiation seemed to decrease the optical band gap energy of HAp thin films. The surface roughness, wettability and bioactivity were improved on irradiation of the samples. Amount of amoxicillin loading/release increased (10%) in ion beam irradiated (1 Multiplication-Sign 10{sup 12} ions cm{sup -2}) sample. Irradiated sample showed fast rate of amoxicillin (AMX) release than the pristine. Bactericidal effect was found to increase on irradiation. Surface modified and antibiotics incorporated HAp coated titanium implants may be used to prevent post-surgical infections and to promote bone-bonding of orthopedic devices.

  13. Enhancement of etch rate for preparation of nano-sized ion-track membranes of poly(vinylidene fluoride): Effect of pretreatment and high-LET beam irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Rohani, Rosiah [Quantum Beam Science Directorate, Japan Atomic Energy Agency (JAEA), 1233 Watanuki, Takasaki, Gunma 370-1292 (Japan); Department of Chemical and Process Engineering, Faculty of Engineering, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia); Yamaki, Tetsuya [Quantum Beam Science Directorate, Japan Atomic Energy Agency (JAEA), 1233 Watanuki, Takasaki, Gunma 370-1292 (Japan)], E-mail: yamaki.tetsuya@jaea.go.jp; Koshikawa, Hiroshi; Takahashi, Shuichi; Hasegawa, Shin; Asano, Masaharu; Maekawa, Yasunari [Quantum Beam Science Directorate, Japan Atomic Energy Agency (JAEA), 1233 Watanuki, Takasaki, Gunma 370-1292 (Japan); Voss, Kay-Obbe; Trautmann, Christina; Neumann, Reinhard [Materials Research Department, Gesellschaft fur Schwerionenforschung mbH (GSI), Planckstrasse 1, D-64291 Darmstadt (Germany)

    2009-02-15

    We investigated how pretreatment and high-LET beam irradiation affected the ion-track dissolution rate in poly(vinylidene fluoride) (PVDF) films by SEM observations and conductometric analysis in order to develop the preparation methodology of nano-sized ion-track membranes. PVDF thin films irradiated with four types of ion beams were exposed to a 9 mol/dm{sup 3} KOH aqueous solution after their storage in air at 120 deg. C. This heating treatment was found to enhance the etch rate in the latent track, both in the inner core and outer halo regions, without changing that in the bulk, probably due to the formation of parasitic oxidation products facilitating the introduction of the etching agent to improve the etchability. Additionally, the irradiation of heavier higher-LET ions, causing each track to more activated sites (like radicals), was preferable for achieving effective etching.

  14. Formation of Co nanodisc with enhanced perpendicular magnetic anisotropy driven by Ga+ ion irradiation on Pt/Co/Pt films

    Science.gov (United States)

    Sakamaki, M.; Amemiya, K.; Sveklo, I.; Mazalski, P.; Liedke, M. O.; Fassbender, J.; Kurant, Z.; Wawro, A.; Maziewski, A.

    2016-11-01

    The origin of magnetic phase transition from in-plane to perpendicular magnetic anisotropy (PMA) of Pt/Co/Pt thin film by Ga+ ion irradiation at fluences of 1 -5 ×1015 ions /cm2 is investigated by means of x-ray magnetic circular dichroism (XMCD) and extended x-ray absorption fine structure (EXAFS) analyses. We find that Pt and Co atoms are mixed with each other and that Co is oxidized near the surface due to removal of the Pt overlayer. Furthermore, polarization-dependent EXAFS analysis shows that Co is firstly dispersed as separated single-atom-thick sheets in a Pt matrix at 1 ×1015 ions /cm2, then the Co sheets are divided into a few Å clusters at 5 ×1015 ions /cm2, which are regarded as nanodiscs parallel to the film plane. This process is accompanied by the appearance of an out-of-plane magnetization component and a remanence peak is observed. Because we do not observe an enhancement in anisotropy of Co orbital moment which leads to change in magnetic anisotropy through the transition at about 5 ×1015 ions /cm2, it might be possible that such nanodisc formation induces increase of magnetic anisotropy via a shape effect. By comparing with the phase transition observed at lower fluence [Phys. Rev. B 86, 024418 (2012), 10.1103/PhysRevB.86.024418], we find that the mechanism of two transitions is different, i.e., the transition at lower fluence is caused by anisotropy of orbital moment due to structural strain, while the present transition is possibly by shape effect due to nanodisc formation.

  15. Enhancement of Electrical Properties of TiO2- x Oxide Semiconductor by d-Orbital Ordering Using Swift Heavy Ni-Ion Irradiation at Room Temperature

    Science.gov (United States)

    Cho, S. H.; Jun, B. H.; Chung, K. B.

    2017-02-01

    The electrical properties of radiofrequency (RF)-sputtered TiO2- x films have been investigated as a function of Ni-ion irradiation dose at room temperature. The prepared TiO2- x films were irradiated with 130-MeV swift heavy Ni ions in the range from 5 × 1011 ions/cm2 to 1 × 1013 ions/cm2. Increasing the Ni-ion irradiation dose dramatically enhanced the mobility in the TiO2- x films from 2.2 cm2/V s to 1.24 × 102 cm2/V s, while the carrier concentration did not vary. To explain this change in the electrical properties of the TiO2- x films, we investigated various physical properties, namely the physical structure, molecular orbital ordering in the conduction band, and shallow/deep trap states in the band-edge area below the conduction band. We suggest that the improvement in mobility originates from the ordering of the Ti 3 d orbital in the conduction band. In addition, increase of the Ni-ion irradiation dose changed two distinct band-edge states below the conduction band.

  16. Enhancement in anomalous Hall resistivity of Co/Pd multilayer and CoPd alloy by Ga+ ion irradiation

    KAUST Repository

    Guo, Zaibing

    2014-02-01

    In this paper, we report the effect of Ga+ ion irradiation on anomalous Hall effect (AHE) and longitudinal resistivity (ρxx) in [Co(3 Å)/Pd(5 Å)]80 multilayer and Co 42Pd58 alloy. 4- and 2-fold increases in anomalous Hall resistivity (ρAH) in the Co/Pd multilayer and CoPd alloy have been observed after irradiations at doses of 2.4 × 1015 and 3.3×10 15 ions/cm2, respectively. Skew scattering and side jump contributions to AHE have been analyzed based on the scaling relationship ρAH = aρxx + bρ2xx. For the Co/Pd multilayer, AHE is mainly affected by ion irradiation-induced interface diffusion and defects. For the CoPd alloy, the increase in doses above 1.5 × 1015 ions/cm2 induces a sign change in skew scattering, followed by the skew scattering contribution to AHE overwhelming the side jump contribution, this phenomenon should be attributed to irradiation-induced defects and modifications in chemical ordering. © Copyright EPLA, 2014.

  17. Enhancement in anomalous Hall resistivity of Co/Pd multilayer and CoPd alloy by Ga+ ion irradiation

    Science.gov (United States)

    Guo, Z. B.; Mi, W. B.; Li, J. Q.; Cheng, Y. C.; Zhang, X. X.

    2014-02-01

    In this paper, we report the effect of Ga+ ion irradiation on anomalous Hall effect (AHE) and longitudinal resistivity (\\rho_{\\textit{xx}}) in [Co(3 Å)/Pd(5 Å)]80 multilayer and Co42Pd58 alloy. 4- and 2-fold increases in anomalous Hall resistivity (\\rho_{\\textit{AH}}) in the Co/Pd multilayer and CoPd alloy have been observed after irradiations at doses of 2.4\\times 10^{15} and 3.3\\times 10^{15}\\ \\text{ions/cm}^{2} , respectively. Skew scattering and side jump contributions to AHE have been analyzed based on the scaling relationship \\rho_{\\textit{AH}}=a\\rho_{\\textit{xx}}+b\\rho_{\\textit{xx}}^{2} . For the Co/Pd multilayer, AHE is mainly affected by ion irradiation-induced interface diffusion and defects. For the CoPd alloy, the increase in doses above 1.5\\times 10^{15}\\ \\text{ions/cm}^{2} induces a sign change in skew scattering, followed by the skew scattering contribution to AHE overwhelming the side jump contribution, this phenomenon should be attributed to irradiation-induced defects and modifications in chemical ordering.

  18. Enhanced AC conductivity and dielectric relaxation properties of polypyrrole nanoparticles irradiated with Ni{sup 12+} swift heavy ions

    Energy Technology Data Exchange (ETDEWEB)

    Hazarika, J.; Kumar, A., E-mail: ask@tezu.ernet.in

    2014-08-15

    In this paper, we report the 160 MeV Ni{sup 12+} swift heavy ions (SHIs) irradiation effects on AC conductivity and dielectric relaxation properties of polypyrrole (PPy) nanoparticles in the frequency range of 42 Hz–5 MHz. Four ion fluences of 5 × 10{sup 10}, 1 × 10{sup 11}, 5 × 10{sup 11} and 1 × 10{sup 12} ions/cm{sup 2} have been used for the irradiation purpose. Transport properties in the pristine and irradiated PPy nanoparticles have been investigated with permittivity and modulus formalisms to study the polarization effects and conductivity relaxation. With increasing ion fluence, the relaxation peak in imaginary modulus (M{sup ″}) plots shifts toward high frequency suggesting long range motion of the charge carriers. The AC conductivity studies suggest correlated barrier hopping as the dominant transport mechanism. The hopping distance (R{sub ω}) of the charge carriers decreases with increasing the ion fluence. Binding energy (W{sub m}) calculations depict that polarons are the dominant charge carriers.

  19. Enhancement of local superconductivity in ferromagnetic FeCrB metallic glass by Ar{sup +} ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Okunev, V D; Samoilenko, Z A [Donetsk Physiko-Technical Institute, Ukrainian National Academy of Sciences, 83114 Donetsk (Ukraine); Szewczyk, A; Szymczak, R; Szymczak, H; Lewandowski, S J; Aleshkevych, P; Wieckowski, J [Institute of Physics, Polish Academy of Sciences, Aleja Lotnikow 32/46, 02-668 Warsaw (Poland); Khmelevskaya, V S; Antoshina, I A, E-mail: okunev@mail.fti.ac.donetsk.ua [Obninsk State Technical University of Atomic Energy, 249020 Obninsk (Russian Federation)

    2011-10-19

    We have reinforced local superconductivity in ferromagnetic Fe{sub 67}Cr{sub 18}B{sub 15} metallic glasses by ion irradiation. Superconductivity in this medium appears due to the presence of large-scale layered clusters of metallic Fe-Cr phase, 150-230A in size, with a ferromagnetic (or superparamagnetic) Fe-rich core and nonmagnetic Cr-rich superconducting shell. Here we show that due to the intensification of concentration phase separation in the Fe-Cr clusters under ion (Ar{sup +}) irradiation, the volume of the superconducting phase increases from the initial 0.4-0.5% up to 7-8%. After irradiation, the resistivity jump {Delta}{rho}/{rho} in the temperature range T = 3.1-3.6 K increases {approx}14 times, reaching 19%, as compared to 1.36% for the initial sample. In the interval of T = 3.1-3.6 K, the rate of resistance change reaches 79% K{sup -1} for the irradiated sample instead of 3.6% K{sup -1} for the initial sample. In the same temperature interval, the rate of magnetoresistance change increases from 3% K{sup -1} for the initial sample up to 70% K{sup -1} after irradiation. (paper)

  20. Giant enhancement of material damage associated to electronic excitation during ion irradiation: The case of LiNbO{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Rivera, A. [Centro de Microanalisis de Materiales (CMAM), Universidad Autonoma de Madrid, Cantoblanco, 28049 Madrid (Spain); Instituto de Microelectronica de Madrid (CNM), CSIC, 28760 Tres Cantos (Spain); Olivares, J. [Centro de Microanalisis de Materiales (CMAM), Universidad Autonoma de Madrid, Cantoblanco, 28049 Madrid (Spain); Instituto de Optica, CSIC, Serrano 121, 28006 Madrid (Spain); Garcia, G. [Laboratory of Synchrotron Light (CELLS), 08193 Bellaterra (Spain); Cabrera, J.M. [Departamento de Fisica de Materiales, Universidad Autonoma de Madrid, Cantoblanco, 28049 Madrid (Spain); Agullo-Rueda, F. [Instituto de Ciencia de Materiales de Madrid, CSIC, Cantoblanco, 28049 Madrid (Spain); Agullo-Lopez, F. [Centro de Microanalisis de Materiales (CMAM), Universidad Autonoma de Madrid, Cantoblanco, 28049 Madrid (Spain); Departamento de Fisica de Materiales, Universidad Autonoma de Madrid, Cantoblanco, 28049 Madrid (Spain)

    2009-06-15

    The structural damage induced by ion irradiation on dielectric materials and associated device degradation has been, so far, explained on the basis of collisional processes mostly ignoring the electronic excitation. Recent work, focused on lithium niobate, offers conclusive evidence that at high ion energy and moderate mass (A{>=}15) electronic excitation may induce a giant enhancement over the damage rate due to nuclear collisions. As a consequence the material becomes amorphized at irradiation fluences far below those required for nuclear collisions alone. These results are expected to have a deep impact on many technologies including storage of radioactive waste, radiation-resistant materials for fusion reactors, lifetime of components and devices in space missions, nano-patterning in electronics and photonics, and possibly heavy-ion therapy in medicine. (copyright 2009 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  1. Engineering polypyrrole nanotubes by 100 MeV Si9+ ion beam irradiation: enhancement of antioxidant activity.

    Science.gov (United States)

    Upadhyay, J; Kumar, A

    2013-12-01

    In this work, the effect of 100 MeV Si(9+) ion beam with four different fluences on antioxidant and structural properties of polypyrrole nanotubes has been investigated. Polypyrrole nanotubes have been synthesized by reactive self degrade template method. Fragmentation of the polypyrrole nanotubes at higher fluence is revealed from the high resolution transmission electron micrograph (HRTEM) and X-ray diffraction (XRD) results. The decrease in characteristics band of polypyrrole in Fourier transmission of infrared spectra (FTIR) spectra suggests the main chain scission of polypyrrole during irradiation. The free radical scavenging activity of pristine and irradiated samples are evaluated by using α, α-diphenyl-β-picrylhydrazyl (DPPH) assay. The decline of the UV-visible absorbance at 516 nm suggests the neutralization of DPPH free radicals through the reaction with polypyrrole. Significant increase in antioxidant activity of polypyrrole nanotubes is observed with increase in ion fluence. © 2013.

  2. Enhancement of photo sensor properties of nanocrystalline ZnO thin film by swift heavy ion irradiation

    Science.gov (United States)

    Mahajan, S. V.; Upadhye, D. S.; Shaikh, S. U.; Birajadar, R. B.; Siddiqui, F. Y.; Bagul, S. B.; Huse, N. P.; Sharma, R. B.

    2015-06-01

    Nanocrystalline Zinc Oxide (ZnO) thin film prepared by Low cost Successive Ionic Layer Adsorption and Reaction (SILAR) method. This film was irradiated by 120 MeV Ni7+ ions with the fluence of 5x1012ions/cm2. The X-ray diffraction study was shows polycrystalline nature with wurtzite structure. The optical properties as absorbance were determined using UV-Spectrophotometer and band gap was also calculated. The Photo Sensor nature was calculated by I-V characteristics with different sources of light 40W, 60W and 100W.

  3. Enhancement of photo sensor properties of nanocrystalline ZnO thin film by swift heavy ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Mahajan, S. V.; Upadhye, D. S.; Bagul, S. B. [Department of Nanotechnology, Dr. Babasaheb Ambedkar Marathwada University, Aurangabad-431004 (India); Shaikh, S. U.; Birajadar, R. B.; Siddiqui, F. Y.; Huse, N. P. [Thin film and Nanotechnology Laboratory, Department of Physics, Dr. Babasaheb Ambedkar Marathwada University, Aurangabad-431004 (India); Sharma, R. B., E-mail: ramphalsharma@yahoo.com, E-mail: rps.phy@gmail.com [Thin film and Nanotechnology Laboratory, Department of Physics, Dr. Babasaheb Ambedkar Marathwada University, Aurangabad-431004 (India); Department of Nanotechnology, Dr. Babasaheb Ambedkar Marathwada University, Aurangabad-431004 (India)

    2015-06-24

    Nanocrystalline Zinc Oxide (ZnO) thin film prepared by Low cost Successive Ionic Layer Adsorption and Reaction (SILAR) method. This film was irradiated by 120 MeV Ni{sup 7+} ions with the fluence of 5x10{sup 12}ions/cm{sup 2}. The X-ray diffraction study was shows polycrystalline nature with wurtzite structure. The optical properties as absorbance were determined using UV-Spectrophotometer and band gap was also calculated. The Photo Sensor nature was calculated by I-V characteristics with different sources of light 40W, 60W and 100W.

  4. Role of low-energy ion irradiation in the formation of an aluminum germanate layer on a germanium substrate by radical-enhanced atomic layer deposition

    Energy Technology Data Exchange (ETDEWEB)

    Fukuda, Yukio, E-mail: y-fukuda@rs.suwa.tus.ac.jp; Yamada, Daichi; Yokohira, Tomoya; Yanachi, Kosei [Tokyo University of Science, Suwa, 5000-1 Toyohira, Chino, Nagano 391-0292 (Japan); Yamamoto, Chiaya; Yoo, Byeonghak; Sato, Tetsuya [University of Yamanashi, 4-3-11 Takeda, Kofu, Yamanashi 400-8511 (Japan); Yamanaka, Junji [University of Yamanashi, 7-32 Miyamae, Kofu, Yamanashi 400-8511 (Japan); Takamatsu, Toshiyuki [SST Inc., 989-6 Shimadadai, Yachiyo, Chiba 276-0004 (Japan); Okamoto, Hiroshi [Hirosaki University, 3 Bunkyo, Hirosaki 036-8561 (Japan)

    2016-03-15

    Radical-enhanced atomic layer deposition uses oxygen radicals generated by a remote microwave-induced plasma as an oxidant to change the surface reactions of the alternately supplied trimethylaluminum precursor and oxygen radicals on a Ge substrate, which leads to the spontaneous formation of an aluminum germanate layer. In this paper, the effects that low-energy ions, supplied from a remote microwave plasma to the substrate along with the oxygen radicals, have on the surface reactions were studied. From a comparative study of aluminum oxide deposition under controlled ion flux irradiation on the deposition surface, it was found that the ions enhance the formation of the aluminum germanate layer. The plasma potential measured at the substrate position by the Langmuir probe method was 5.4 V. Assuming that the kinetic energy of ions arriving at the substrate surface is comparable to that gained by this plasma potential, such ions have sufficient energy to induce exchange reactions of surface-adsorbed Al atoms with the underlying Ge atoms without causing significant damage to the substrate. This ion-induced exchange reaction between Al and Ge atoms is inferred to be the background kinetics of the aluminum germanate formation by radical-enhanced atomic layer deposition.

  5. Surface Modification of Polymer Substrates by Oxygen Ion Irradiation

    Science.gov (United States)

    Takaoka, G. H.; Ryuto, H.; Araki, R.; Yakushiji, T.

    2008-11-01

    Oxygen cluster ions and/or monomer ions were used for the sputtering and the surface modification of polymers such as polycarbonate (PC) and polyethylene terephthalate (PET). For the case of oxygen cluster ion irradiation, the sputtered depth increased with increase of the acceleration voltage, and the sputtering yield was much larger than that by the monomer ion irradiation. The sputtered particles represented the polymer structure, which indicated that the bond scission by the cluster ion irradiation resulted in an ejection of monomer molecule through the intermolecular collision. On the other hand, for the oxygen monomer ion irradiation, the implanted depth increased with increase of the acceleration voltage, and the bond scission occurred at the deep region through the binary collision with the high energetic ions. Therefore, the sputtering yield for the polymer surfaces decreased, and the sputtering effect became very small. Furthermore, the simultaneous use of oxygen cluster and monomer ions was more effective for oxidation of the PET surfaces rather than the monomer ion irradiation or the cluster ion irradiation. As a result, the contact angle measurement showed that the wettability of the PET surfaces irradiated by the simultaneous use of oxygen cluster and monomer ions was much enhanced.

  6. Graphitization of polymer surfaces by scanning ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Koval, Yuri [Department of Physics, Universität Erlangen-Nürnberg, Erwin-Rommel-Str. 1, 91058 Erlangen (Germany)

    2014-10-20

    Graphitization of polymer surfaces was performed by low-energy Ar{sup +} and He{sup +} ion irradiation. A method of scanning irradiation was implemented. It was found that by scanning ion irradiation, a significantly higher electrical conductivity in the graphitized layers can be achieved in comparison with a conventional broad-beam irradiation. The enhancement of the conductance becomes more pronounced for narrower and better collimated ion beams. In order to analyze these results in more detail, the temperature dependence of conductance of the irradiated samples was investigated. The results of measurements are discussed in terms of weak localization corrections to conductance in disordered metals. The observed effects can be explained by enlargement of graphitic patches, which was achieved with the scanning ion irradiation method.

  7. Oxygen intake in ion irradiated fullerene films

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, Amit [Department of Nanosciences, Neel Institute, C.N.R.S., 25 rue des Martyrs, BP166 38042 Grenoble Cedex 9 (France); Materials Science Group, Inter University Accelerator Centre, P.O. Box 10502, New Delhi 110 067 (India)], E-mail: amit.kumar@grenoble.cnrs.fr; Khan, S.A. [Materials Science Group, Inter University Accelerator Centre, P.O. Box 10502, New Delhi 110 067 (India); Kumar, Manvendra [Physics Department, Allahabad University, P.O. Box 211002 (India); Agarwal, D.C. [RBS College, Agra (India); Singh, Fouran; Tripathi, A. [Materials Science Group, Inter University Accelerator Centre, P.O. Box 10502, New Delhi 110 067 (India); Govind; Shivaprasad, S.M. [Surface Physics and Nanostructures Group, NPL, New Delhi 110 060 (India); Salomon, J.; Pichon, L. [C2RMF, Palais du Louvre, 75001 Paris (France); Pivin, J.C. [CSNSM, 91405 Orsay Campus (France); Avasthi, D.K. [Department of Nanosciences, Neel Institute, C.N.R.S., 25 rue des Martyrs, BP166 38042 Grenoble Cedex 9 (France)

    2008-04-15

    The present work reports the change in the oxygen content in energetic ion irradiated fullerene films. The oxygen contents in irradiated films have been studied using on-line elastic recoil detection analysis (ERDA) and off-line X-ray photo electron emission (XPS) and nuclear reaction analysis (NRA) techniques. The XPS and NRA techniques show that the oxygen content increases with ion fluence, whereas on-line ERDA measurements reveal that the oxygen content decreases with ion fluence. These experiments give clear evidence that oxygen content in irradiated films increases after exposure to the atmospheric oxygen.

  8. Enhanced Radiation-tolerant Oxide Dispersion Strengthened Steel and its Microstructure Evolution under Helium-implantation and Heavy-ion Irradiation

    Science.gov (United States)

    Lu, Chenyang; Lu, Zheng; Wang, Xu; Xie, Rui; Li, Zhengyuan; Higgins, Michael; Liu, Chunming; Gao, Fei; Wang, Lumin

    2017-01-01

    The world eagerly needs cleanly-generated electricity in the future. Fusion reactor is one of the most ideal energy resources to defeat the environmental degradation caused by the consumption of traditional fossil energy. To meet the design requirements of fusion reactor, the development of the structural materials which can sustain the elevated temperature, high helium concentration and extreme radiation environments is the biggest challenge for the entire material society. Oxide dispersion strengthened steel is one of the most popular candidate materials for the first wall/blanket applications in fusion reactor. In this paper, we evaluate the radiation tolerance of a 9Cr ODS steel developed in China. Compared with Ferritic/Martensitic steel, this ODS steel demonstrated a significantly higher swelling resistance under ion irradiation at 460 °C to 188 displacements per atom. The role of oxides and grain boundaries on void swelling has been explored. The results indicated that the distribution of higher density and finer size of nano oxides will lead a better swelling resistance for ODS alloy. The original pyrochlore-structured Y2Ti2O7 particles dissolved gradually while fine Y-Ti-O nano clusters reprecipitated in the matrix during irradiation. The enhanced radiation tolerance is attributed to the reduced oxide size and the increased oxide density.

  9. Enhanced Radiation-tolerant Oxide Dispersion Strengthened Steel and its Microstructure Evolution under Helium-implantation and Heavy-ion Irradiation.

    Science.gov (United States)

    Lu, Chenyang; Lu, Zheng; Wang, Xu; Xie, Rui; Li, Zhengyuan; Higgins, Michael; Liu, Chunming; Gao, Fei; Wang, Lumin

    2017-01-12

    The world eagerly needs cleanly-generated electricity in the future. Fusion reactor is one of the most ideal energy resources to defeat the environmental degradation caused by the consumption of traditional fossil energy. To meet the design requirements of fusion reactor, the development of the structural materials which can sustain the elevated temperature, high helium concentration and extreme radiation environments is the biggest challenge for the entire material society. Oxide dispersion strengthened steel is one of the most popular candidate materials for the first wall/blanket applications in fusion reactor. In this paper, we evaluate the radiation tolerance of a 9Cr ODS steel developed in China. Compared with Ferritic/Martensitic steel, this ODS steel demonstrated a significantly higher swelling resistance under ion irradiation at 460 °C to 188 displacements per atom. The role of oxides and grain boundaries on void swelling has been explored. The results indicated that the distribution of higher density and finer size of nano oxides will lead a better swelling resistance for ODS alloy. The original pyrochlore-structured Y2Ti2O7 particles dissolved gradually while fine Y-Ti-O nano clusters reprecipitated in the matrix during irradiation. The enhanced radiation tolerance is attributed to the reduced oxide size and the increased oxide density.

  10. RBE of Cells Irradiated by Carbon Ions

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The cells were mouse melanoma B16,human cervical squamous carcinoma HeLa,Chinese hamster pulmonary V79,and human hepatoma SMMC-7721.For~(12)C ion experiment,the cells of 1.55×10~5/ml were seeded in 35mm diameter petri dish and allowed to grow one day befbre irradiation.When immediately irradiated,the medium

  11. Neurite outgrowth on fluorinated polyimide film micropatterned by ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Okuyama, Y.; Sato, M.; Nagaoka, S.; Kawakami, H. E-mail: kawakami-hiroyoshi@c.metro-u.ac.jp; Suzuki, Y.; Iwaki, M

    2003-05-01

    In this study, we investigated neurite outgrowth on a fluorinated polyimide film micropatterned by ion irradiation. We used the fluorinated polyimide because of its excellent thermal and mechanical properties and biocompatibility. Rattus norvegicus chromaphin (PC12) cells were used for in vitro studies. The polyimide films were irradiated with He{sup +}, Ne{sup +} or Kr{sup +} at 1 x 10{sup 14} ions/cm{sup 2} using an ion-beam mask. The lines in the mask were 120 and 160 {mu}m wide and 120-160 {mu}m apart. PC12 cells were selectively adhered on the polyimide film micropatterned by Kr{sup +}-irradiation. However, the neurite length on the film irradiated by Kr{sup +} was shorter than that determined in the film irradiated by He{sup +}. On the other hand, neurite outgrowth on the polyimide film micropatterned by He{sup +}-irradiation was at least 100 {mu}m in length. This initial study indicated the enhanced outgrowth of PC12 cells on the fluorinated polyimide film micropatterned by ion irradiation.

  12. Irradiation induced grain growth and surface emission enhancement of chemically tailored ZnS : Mn/PVOH nanoparticles by Cl+9 ion impact

    Indian Academy of Sciences (India)

    D Mohanta; S S Nath; N C Mishra; A Choudhury

    2003-04-01

    Manganese doped zinc sulfide nanoparticles are fabricated on polyvinyl alcohol dielectric matrix. They are bombarded with energetic chlorine ions (100 MeV). The size of the crystallites is found to increase with ion fluence due to melting led grain growth under ion irradiation. The increased size as a result of grain growth has been observed both in the optical absorption spectra in terms of redshift and in electron microscopic images. The photoluminescence (PL) study was carried out by band to band excitation ($\\lambda_{ex}$ = 220 nm) upon ZnS : Mn, which results into two emission peaks corresponding to surface states and Mn+2 emission, respectively. The ion fluence for irradiation experiment so chosen were 1 × 1011, 5 × 1011, 5 × 1012 and 1013 Cl/cm2.

  13. Dissolution of ordered precipitates under ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Camus, E.; Bourdeau, F.; Abromeit, C.; Wanderka, N.; Wollenberger, H. [Hahn-Meitner-Institut Berlin GmbH (Germany)

    1995-09-01

    The stability of the ordered {gamma}{prime} precipitates under 300-keV Ni{sup +} irradiation was investigated between room temperature and 623 K. The two competing mechanisms of destabilization by cascade producing irradiation, i.e. disordering and dissolution of the {gamma}{prime} precipitates in Nimonic PE16 alloy, has been studied separately by electron microscopy and field-ion microscopy with atom probe. At high temperatures, the precipitates are stable. At intermediate temperatures, the precipitates dissolve by ballistic mixing into the matrix, but the interface is restored by the radiation-enhanced atomic jumps. The order in the precipitates remains stable. At low temperatures, the precipitates are dissolved by atomic mixing. The dissolution proceeds in a diffusional manner with a diffusion coefficient normalized by the displacement rate D/K = 0.75 nm{sup 2}dpa{sup {minus}1}. The precipitates become disordered by a fluence of 0.1 dpa, whereas precipitate dissolution needs much higher fluences.

  14. Fast ion energy flux enhancement from ultra thin foils irradiated by intense and high contrast short laser pulses

    NARCIS (Netherlands)

    Andreev, A.; Levy, A.; Ceccotti, T.; Thaury, C.; Platonov, K.; Loch, R.A.; Martin, Ph.

    2008-01-01

    Recent significant improvements of the contrast ratio of chirped pulse amplified pulses allows us to extend the applicability domain of laser accelerated protons to very thin targets. In this framework, we propose an analytical model particularly suitable to reproducing ion laser acceleration

  15. Ion irradiation effects on metallic nanocrystals

    Science.gov (United States)

    Kluth, P.; Johannessen, B.; Giulian, R.; Schnohr, C. S.; Foran, G. J.; Cookson, D. J.; Byrne, A. P.; Ridgway, M. C.

    We have investigated structural and morphological properties of metallic nanocrystals (NCs) exposed to ion irradiation. NCs were characterized by transmission electron microscopy in combination with advanced synchrotron-based analytical techniques, in particular X-ray absorption spectroscopy and small-angle X-ray scattering. A number of different effects were observed depending on the irradiation conditions. At energies where nuclear stopping is predominant, structural disorder/amorphization followed by inverse Ostwald ripening/dissolution due to ion beam mixing was observed for Au and Cu NCs embedded in SiO2. The ion-irradiation-induced crystalline to amorphous transition in the NCs, which cannot be achieved in the corresponding bulk metals, was attributed to their initially higher structural energy as compared to bulk material and possibly preferential nucleation of the amorphous phase at the NC/SiO2 interface. At very high irradiation energies (swift heavy ion irradiation), where the energy loss is nearly entirely due to electronic stopping, a size-dependent shape transformation of the NCs from spheres to rod like shapes was apparent in Au NCs. Our preliminary results are in good agreement with considerations on melting of the NCs in the ion track as one mechanism involved in the shape transformation.

  16. Ion irradiation induced direct damage to DNA

    CERN Document Server

    Wang, Wei; Su, Wenhui

    2008-01-01

    Ion beams have been widely applied in a few biological research fields such as radioactive breeding, health protection, and tumor therapy. Up to now many interesting and impressive achievements in biology and agriculture have been made. Over the past several decades, scientists in biology, physics, and chemistry have pursued investigations focused on understanding the mechanisms of these radiobiological effects of ion beams. From the chemical point of view, these effects are due to the ion irradiation induced biomolecular damage, direct or indirect. In this review, we will present a chemical overview of the direct effects of ion irradiation upon DNA and its components, based on a review of literature combined with recent experimental results. It is suggested that, under ion bombardment, a DNA molecule undergoes a variety of processes, including radical formation, atomic displacement, intramolecular bond-scissions, emission of fragments, fragment recombination and molecular crosslink, which may lead to genetic...

  17. Effects of ion beam irradiation on semiconductor devices

    Energy Technology Data Exchange (ETDEWEB)

    Nashiyama, Isamu; Hirao, Toshio; Itoh, Hisayoshi; Ohshima, Takeshi [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment

    1997-03-01

    Energetic heavy-ion irradiation apparatus has been developed for single-event effects (SEE) testing. We have applied three irradiation methods such as a scattered-ion irradiation method, a recoiled-atom irradiation method, and a direct-beam irradiation method to perform SEE testing efficiently. (author)

  18. Cell adhesion behavior on the silicone rubber surface modified by using ion beam irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, In Tae; Jung, Chan Hee; Nh, Young Chang; Choi, Jae Hak [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Kuk, In Seol [Hanyang University, Seoul (Korea, Republic of); An, Mi Young [Chungnam National University, Daejeon (Korea, Republic of)

    2009-12-15

    In this study we studied cell adhesion and proliferation on the surface of a silicone rubber modified by ion beam irradiation. The surface property of the irradiated silicone rubber was characterized by water contact angle and FT-IR analyses. It was observed that human (HEK293) fibroblast cells exhibit strong adhesion to the irradiated silicone surface. This enhanced adhesion of mammalian cells can be attributed to the increase in the hydrophilicity of the silicone surface by ion beam irradiation.

  19. In-situ high temperature irradiation setup for temperature dependent structural studies of materials under swift heavy ion irradiation

    Science.gov (United States)

    Kulriya, P. K.; Kumari, Renu; Kumar, Rajesh; Grover, V.; Shukla, R.; Tyagi, A. K.; Avasthi, D. K.

    2015-01-01

    An in-situ high temperature (1000 K) setup is designed and installed in the materials science beam line of superconducting linear accelerator at the Inter-University Accelerator Centre (IUAC) for temperature dependent ion irradiation studies on the materials exposed with swift heavy ion (SHI) irradiation. The Gd2Ti2O7 pyrochlore is irradiated using 120 MeV Au ion at 1000 K using the high temperature irradiation facility and characterized by ex-situ X-ray diffraction (XRD). Another set of Gd2Ti2O7 samples are irradiated with the same ion beam parameter at 300 K and simultaneously characterized using in-situ XRD available in same beam line. The XRD studies along with the Raman spectroscopic investigations reveal that the structural modification induced by the ion irradiation is strongly dependent on the temperature of the sample. The Gd2Ti2O7 is readily amorphized at an ion fluence 6 × 1012 ions/cm2 on irradiation at 300 K, whereas it is transformed to a radiation-resistant anion-deficient fluorite structure on high temperature irradiation, that amorphized at ion fluence higher than 1 × 1013 ions/cm2. The temperature dependent ion irradiation studies showed that the ion fluence required to cause amorphization at 1000 K irradiation is significantly higher than that required at room temperature irradiation. In addition to testing the efficiency of the in-situ high temperature irradiation facility, the present study establishes that the radiation stability of the pyrochlore is enhanced at higher temperatures.

  20. ESR investigations on ion beam irradiated polycarbonate

    Energy Technology Data Exchange (ETDEWEB)

    Chipara, M.I. (Institute for Physics and Technology of Materials, P.O. Box MG-7, Magurele, Bucharest, R-76900 (Romania)); Grecu, V.V. (University of Bucharest, Faculty of Physics, P.O. Box MG-11, Magurele, Bucharest, R-76900 (Romania)); Notingher, P.V. (University Politehnica of Bucharest, Electrotechnical Faculty, 313, Splaiul Independentei, Str., 77206 Bucharest (Romania)); Romero, J.R. (Universidad Central de Venezuela, Facultad de Ingineria, Dept. de Fisica Aplicada, Ciudad Universitaria, Chaguaramos, Caracas (Venezuela)); Chipara, M.D. (Research Institute for Electrotechnics, 45-47 Tudor Vladimirescu, Bd., Bucharest, R-79623 (Romania))

    1994-06-01

    Electron spin resonance (ESR) investigations with a polycarbonate solid state nuclear detector, irradiated with oxygen ions, are reported. The nature of the paramagnetic defects induced by irradiation is discussed. The temperature dependence of resonance line parameters is studied. From the experimental data, obtained by ESR, spectroscopy, the activation energy for defect recombination, the average isotropic exchange integral between paramagnetic defects as well as the average distance between defects, are estimated. Correlations with latent tracks structure are discussed. ((orig.))

  1. Radiation stability of iron nanoparticles irradiated with accelerated iron ions

    Energy Technology Data Exchange (ETDEWEB)

    Uglov, V.V., E-mail: uglov@bsu.by [Belarusian State University, Nezavisimosty ave., 4, Minsk 220030 (Belarus); Tomsk Polytechnic University, Lenina ave., 2a, Tomsk 634028 (Russian Federation); Remnev, G.E., E-mail: remnev06@mail.ru [Tomsk Polytechnic University, Lenina ave., 2a, Tomsk 634028 (Russian Federation); Kvasov, N.T.; Safronov, I.V.; Shymanski, V.I. [Belarusian State University, Nezavisimosty ave., 4, Minsk 220030 (Belarus)

    2015-07-01

    Highlights: • Dynamic processes in nanoparticles after ion irradiation were studied. • The mechanism of the enhanced radiation stability of nanoparticles was showed. • The criteria of the enhanced radiation stability of nanoparticles was proposed. - Abstract: In the present work the dynamic processes occurring in a nanoscale iron particle exposed to irradiation with iron ions of different energies are studied in detailed. It is shown that the elastic and thermoelastic crystal lattice responses to irradiation form force factors affecting the evolution of defect-impurity system, which, in turn, leads to a decrease in the number of structural defects. Quantitative estimations of the spatial distribution of defects resulting in their migration to the surface were obtained. Such self-organization of nanoparticles exposed to ionizing radiation can be used as a basis for the production of radiation-resistant nanostructured materials capable of sustaining a long-term radiation influence.

  2. Heavy ion irradiation of crystalline water ice

    CERN Document Server

    Dartois, E; Boduch, P; Brunetto, R; Chabot, M; Domaracka, A; Ding, J J; Kamalou, O; Lv, X Y; Rothard, H; da Silveira, E F; Thomas, J C

    2015-01-01

    Under cosmic irradiation, the interstellar water ice mantles evolve towards a compact amorphous state. Crystalline ice amorphisation was previously monitored mainly in the keV to hundreds of keV ion energies. We experimentally investigate heavy ion irradiation amorphisation of crystalline ice, at high energies closer to true cosmic rays, and explore the water-ice sputtering yield. We irradiated thin crystalline ice films with MeV to GeV swift ion beams, produced at the GANIL accelerator. The ice infrared spectral evolution as a function of fluence is monitored with in-situ infrared spectroscopy (induced amorphisation of the initial crystalline state into a compact amorphous phase). The crystalline ice amorphisation cross-section is measured in the high electronic stopping-power range for different temperatures. At large fluence, the ice sputtering is measured on the infrared spectra, and the fitted sputtering-yield dependence, combined with previous measurements, is quadratic over three decades of electronic ...

  3. Irradiation-enhanced reactivity of multilayer Al/Ni nanomaterials.

    Science.gov (United States)

    Manukyan, Khachatur V; Tan, Wanpeng; deBoer, Richard J; Stech, Edward J; Aprahamian, Ani; Wiescher, Michael; Rouvimov, Sergei; Overdeep, Kyle R; Shuck, Christopher E; Weihs, Timothy P; Mukasyan, Alexander S

    2015-06-03

    We have investigated the effect of accelerated ion beam irradiation on the structure and reactivity of multilayer sputter deposited Al/Ni nanomaterials. Carbon and aluminum ion beams with different charge states and intensities were used to irradiate the multilayer materials. The conditions for the irradiation-assisted self-ignition of the reactive materials and corresponding ignition thresholds for the beam intensities were determined. We discovered that relatively short (40 min or less) ion irradiations enhance the reactivity of the Al/Ni nanomaterials, that is, significantly decrease the thermal ignition temperatures (Tig) and ignition delay times (τig). We also show that irradiation leads to atomic mixing at the Al/Ni interfaces with the formation of an amorphous interlayer, in addition to the nucleation of small (2-3 nm) Al3Ni crystals within the amorphous regions. The amorphous interlayer is thought to enhance the reactivity of the multilayer energetic nanomaterial by increasing the heat of the reaction and by speeding the intermixing of the Ni and the Al. The small Al3Ni crystals may also enhance reactivity by facilitating the growth of this Al-Ni intermetallic phase. In contrast, longer irradiations decrease reactivity with higher ignition temperatures and longer ignition delay times. Such changes are also associated with growth of the Al3Ni intermetallic and decreases in the heat of reaction. Drawing on this data set, we suggest that ion irradiation can be used to fine-tune the structure and reactivity of energetic nanomaterials.

  4. In situ ion irradiation of zirconium carbide

    Science.gov (United States)

    Ulmer, Christopher J.; Motta, Arthur T.; Kirk, Mark A.

    2015-11-01

    Zirconium carbide (ZrC) is a candidate material for use in one of the layers of TRISO coated fuel particles to be used in the Generation IV high-temperature, gas-cooled reactor, and thus it is necessary to study the effects of radiation damage on its structure. The microstructural evolution of ZrCx under irradiation was studied in situ using the Intermediate Voltage Electron Microscope (IVEM) at Argonne National Laboratory. Samples of nominal stoichiometries ZrC0.8 and ZrC0.9 were irradiated in situ using 1 MeV Kr2+ ions at various irradiation temperatures (T = 20 K-1073 K). In situ experiments made it possible to continuously follow the evolution of the microstructure during irradiation using diffraction contrast imaging. Images and diffraction patterns were systematically recorded at selected dose points. After a threshold dose during irradiations conducted at room temperature and below, black-dot defects were observed which accumulated until saturation. Once created, the defect clusters did not move or get destroyed during irradiation so that at the final dose the low temperature microstructure consisted only of a saturation density of small defect clusters. No long-range migration of the visible defects or dynamic defect creation and elimination were observed during irradiation, but some coarsening of the microstructure with the formation of dislocation loops was observed at higher temperatures. The irradiated microstructure was found to be only weakly dependent on the stoichiometry.

  5. Anisotropic dewetting of ion irradiated solid films

    Energy Technology Data Exchange (ETDEWEB)

    Repetto, L., E-mail: luca.repetto@unige.it [Dipartimento di fisica, Università di Genova, Via Dodecaneso 33, 16146 Genova (Italy); Šetina Batič, B. [Inštitut Za Kovinske Materiale in Tehnologije, Lepi pot 11, 1000 Ljubljana (Slovenia); Firpo, G.; Piano, E.; Valbusa, U. [Dipartimento di fisica, Università di Genova, Via Dodecaneso 33, 16146 Genova (Italy)

    2013-11-15

    Experiments of irradiation with 30 keV Ga ions were conducted on ultrathin chromium films on rippled silicon substrates. The evolution of their surface morphology, as detected by real time scanning electron microscopy, shows an apparent differential sputtering yield for regions of positive and negative curvature which is in contrast with the standard theory for curvature depending sputtering yield. In particular, at the end of the irradiation process, chromium wires are left in the valleys of the substrate. This result was explained in terms of local melting caused by the ion impact and of a process of dewetting under the concurring actions of surface tension and Van der Waals forces while ion sputtering is active. The interpretation of the reported experimental results are fully supported by numeric simulations implementing the same continuum model used to explain ion induced spinodal dewetting. This hierarchical self-organization process breaks the symmetry of previously demonstrated ion induced dewetting, making possible to create new structures by using the same fundamental effects.

  6. Nanoscale Morphology Evolution Under Ion Irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Aziz, Michael J. [President & Fellows of Harvard College, Cambridge, MA (United States)

    2014-11-10

    We showed that the half-century-old paradigm of morphological instability under irradiation due to the curvature-dependence of the sputter yield, can account neither for the phase diagram nor the amplification or decay rates that we measure in the simplest possible experimental system -- an elemental semiconductor with an amorphous surface under noble-gas ion irradiation; We showed that a model of pattern formation based on the impact-induced redistribution of atoms that do not get sputtered away explains our experimental observations; We developed a first-principles, parameter-free approach for predicting morphology evolution, starting with molecular dynamics simulations of single ion impacts, lasting picoseconds, and upscaling through a rigorous crater-function formalism to develop a partial differential equation that predicts morphology evolution on time scales more than twelve orders of magnitude longer than can be covered by the molecular dynamics; We performed the first quantitative comparison of the contributions to morphological instability from sputter removal and from impact-induced redistribution of atoms that are removed, and showed that the former is negligible compared to the latter; We established a new paradigm for impact-induced morphology evolution based on crater functions that incorporate both redistribution and sputter effects; and We developed a model of nanopore closure by irradiation-induced stress and irradiationenhanced fluidity, for the near-surface irradiation regime in which nuclear stopping predominates, and showed that it explains many aspects of pore closure kinetics that we measure experimentally.

  7. Ion irradiation induced effects in polyamidoimide

    Energy Technology Data Exchange (ETDEWEB)

    Merhari, L.; Belorgeot, C.; Moliton, J.P. (Laboratoire d' Electronique des Polymeres sous Faisceaux Ioniques 123, avenue Albert Thomas, 87060 Limoges Cedex (France))

    1991-09-01

    The interaction between ion beam and polyamidoimide (PAI) is studied by means of low-temperature infrared spectroscopy. 200 keV Ar{sup +} and 250 keV He{sup +} beams with fluences ranging from 10{sup 13} ions cm{sup {minus}2} to 5{times}10{sup 16} ions cm{sup {minus}2} are found to induce atomic bond breaks leading to absorption bands at 2344, 2261, and 2125 cm{sup {minus}1} corresponding respectively to CO{sub 2}, C=N=N and C=N--R vibrations. Shrinkage of the polymer along with a drastic decrease of the resistivity during Ar{sup +} and He{sup +} irradiation are observed. Speculations on the respective role of electronic processes and atomic collisions in the evolution of the polymer are made. No evidence of PAI modification through knock-on mechanism for fluences lower than 5{times}10{sup 15} ions cm{sup {minus}2} is noticed. In fact, our results would suggest a predominant role of the electronic processes for the low fluences (up to 5{times}10{sup 15} ions cm{sup {minus}2} ), whereas a degradation mechanism based on atomic collisions is more likely to take place for higher fluences. A theoretical mechanism of reactions based upon our Fourier transform infrared (FTIR) and secondary ion mass spectroscopies (SIMS) results, describing the chemical changes occurring in the PAI, is presented and briefly discussed.

  8. Local brain heavy ion irradiation induced Immunosuppression

    Science.gov (United States)

    Lei, Runhong; Deng, Yulin; Huiyang Zhu, Bitlife.; Zhao, Tuo; Wang, Hailong; Yu, Yingqi; Ma, Hong; Wang, Xiao; Zhuang, Fengyuan; Qing, Hong

    Purpose: To investigate the long term effect of acute local brain heavy ion irradiation on the peripheral immune system in rat model. Methodology: Only the brain of adult male Wistar rats were radiated by heavy ions at the dose of 15 Gy. One, two and three months after irradiation, thymus and spleen were analyzed by four ways. Tunel assay was performed to evaluate the percentage of apoptotic cells in thymus and spleen, level of Inflammatory cytokines (IL-2, IL-6, SSAO, and TNF-α) was detected by ELISA assay, the differentiation of thymus T lymphocyte subsets were measured by flow cytometry and the relative expression levels of genes related to thymus immune cell development were measured by using quantitative real-time PCR. Results: Thymus and spleen showed significant atrophy from one month to three months after irradiation. A high level of apoptosis in thymus and spleen were obtained and the latter was more vulnerable, also, high level of inflammatory cytokines were found. Genes (c-kit, Rag1, Rag2 and Sca1) related to thymus lymphocytes’ development were down-regulated. Conclusion: Local area radiation in the rat brain would cause the immunosuppression, especially, the losing of cell-mediated immune functions. In this model, radiation caused inflammation and then induced apoptosis of cells in the immune organs, which contributed to immunosuppression.

  9. Growth Enhancement of Radish Sprouts Induced by Low Pressure O2 Radio Frequency Discharge Plasma Irradiation

    Science.gov (United States)

    Kitazaki, Satoshi; Koga, Kazunori; Shiratani, Masaharu; Hayashi, Nobuya

    2012-01-01

    We studied growth enhancement of radish sprouts (Raphanus sativus L.) induced by low pressure O2 radio frequency (RF) discharge plasma irradiation. The average length of radish sprouts cultivated for 7 days after O2 plasma irradiation is 30-60% greater than that without irradiation. O2 plasma irradiation does not affect seed germination. The experimental results reveal that oxygen related radicals strongly enhance growth, whereas ions and photons do not.

  10. Ion irradiated graphite exposed to fusion-relevant deuterium plasma

    Energy Technology Data Exchange (ETDEWEB)

    Deslandes, Alec, E-mail: acd@ansto.gov.au [Institute of Materials Engineering, Australian Nuclear Science and Technology Organisation, Sydney (Australia); Institute for Environmental Research, Australian Nuclear Science and Technology Organisation, Sydney (Australia); Guenette, Mathew C. [Institute of Materials Engineering, Australian Nuclear Science and Technology Organisation, Sydney (Australia); Corr, Cormac S. [Plasma Research Laboratory, Research School of Physics and Engineering, The Australian National University, Canberra 0200 (Australia); Karatchevtseva, Inna [Institute of Materials Engineering, Australian Nuclear Science and Technology Organisation, Sydney (Australia); Thomsen, Lars [Australian Synchrotron, 800 Blackburn Road, Clayton, Victoria 3168 (Australia); Ionescu, Mihail [Institute for Environmental Research, Australian Nuclear Science and Technology Organisation, Sydney (Australia); Lumpkin, Gregory R.; Riley, Daniel P. [Institute of Materials Engineering, Australian Nuclear Science and Technology Organisation, Sydney (Australia)

    2014-12-01

    Graphite samples were irradiated with 5 MeV carbon ions to simulate the damage caused by collision cascades from neutron irradiation in a fusion environment. The ion irradiated graphite samples were then exposed to a deuterium plasma in the linear plasma device, MAGPIE, for a total ion fluence of ∼1 × 10{sup 24} ions m{sup −2}. Raman and near edge X-ray absorption fine structure (NEXAFS) spectroscopy were used to characterize modifications to the graphitic structure. Ion irradiation was observed to decrease the graphitic content and induce disorder in the graphite. Subsequent plasma exposure decreased the graphitic content further. Structural and surface chemistry changes were observed to be greatest for the sample irradiated with the greatest fluence of MeV ions. D retention was measured using elastic recoil detection analysis and showed that ion irradiation increased the amount of retained deuterium in graphite by a factor of four.

  11. Critical current density enhancement by ion irradiation for thick YBa{sub 2}Cu{sub 3}O{sub 7−δ} films prepared by diffusion reaction technique

    Energy Technology Data Exchange (ETDEWEB)

    Kujur, A. [Department of Physics, NIT, Rourkela, Odisha 769 008 (India); Asokan, K. [IUAC, Aruna Asaf Ali Marg, New Delhi 110 067 (India); Behera, D., E-mail: dhrubananda_behera@yahoo.co.in [Department of Physics, NIT, Rourkela, Odisha 769 008 (India)

    2015-01-15

    In the present work we have investigated the effect of 200 MeV Ag ions on YBa{sub 2}Cu{sub 3}O{sub 7−δ}/Y{sub 2}O{sub 3} (5 wt.% and 10 wt.%) composite thick films. The samples were characterized using temperature dependent resistivity and magnetization measurements. The residual resistivity, mean field transition temperature and the zero resistance state are appreciably modified due to swift heavy ion irradiation (SHI). With the increase in defect density for 10 wt.% Y{sub 2}O{sub 3} added samples irradiated with Φ ⩾ 5 × 10{sup 11} ions/cm{sup 2} shows semiconducting behavior above the transition temperature marked by broadening of transition width. Pseudogap temperature regime estimated from the deviation of linear behaviour from resistivity data indicates a shift to lower temperature zone. Synergetic effect of SHI and Y{sub 2}O{sub 3} show enhancement of critical current density and flux pinning at 40 K for 5 wt.% Y{sub 2}O{sub 3} inclusions. However, 10 wt.% Y{sub 2}O{sub 3} added films after ion bombardment records lower values of critical current density and flux pinning. The results are explained on the basis of interplay of defect density and pinning of vortices in the YBCO matrix.

  12. Modification of graphene by ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Bukowska, Hanna; Akcoeltekin, Sevilay; El Kharrazi, Mourad; Schleberger, Marika [Universitaet Duisburg-Essen, Fakultaet fuer Physik, Duisburg (Germany); Osmani, Orkhan [Universitaet Duisburg-Essen, Fakultaet fuer Physik, Duisburg (Germany); Technische Universitaet Kaiserslautern, Fachbereich Physik, Gottlieb-Daimler-Strasse, Gebaeude 47, 67663 Kaiserslautern (Germany)

    2010-07-01

    Ion irradiation can be used to modify surfaces on the nanometer scale. We investigate graphene on different insulator (SrTiO{sub 3}, TiO{sub 2}, and Al{sub 2}O{sub 3}) and semiconductor (SiO{sub 2}) substrates. The bombardment of those target surfaces with swift heavy ions under grazing angle of incidence creates chains of nanodots on the substrate and folds graphene to typical origami-like structures. The shape of the folded graphene seems to depend on the length of the tracks. The length can be controlled by the angle of incidence. From the analysis of atomic force microscopy measurements, we classify the different types of modifications, with the aim to determine the relationship between chain length and origami shape. Further more we want to develop a theoretical understanding of the physical processes leading to the folding.

  13. Physical and biological properties of the ion beam irradiated PMMA-based composite films

    Energy Technology Data Exchange (ETDEWEB)

    Shanthini, G.M.; Martin, Catherine Ann; Sakthivel, N.; Veerla, Sarath Chandra; Elayaraja, K. [Crystal Growth Centre, Anna University, Chennai 600025 (India); Lakshmi, B.S. [Department of Biotechnology, Anna University, Chennai 600025 (India); Asokan, K.; Kanjilal, D. [Materials Science Group, Inter University Accelerator Centre, Aruna Asaf Ali Marg, New Delhi 110067 (India); Kalkura, S. Narayana, E-mail: kalkurasn@annauniv.edu [Crystal Growth Centre, Anna University, Chennai 600025 (India)

    2015-02-28

    Highlights: • First report of swift heavy ion irradiation on PMMA-HAp as bioceramic composite. • Augmented protein adsorption of about 400% was attained due to irradiation. • Tailored surface morphology, topography, roughness, wettability and crystallinity. • Irradiation transformed the hydrophobic surface into hydrophilic surface. • Better blood and cell–material interaction leading to improved biocompatibility. - Abstract: Polymethyl methacrylate (PMMA) and PMMA-hydroxyapatite (PMMA-HAp) composite films, prepared by the solvent evaporation method were irradiated with 100 MeV Si{sup 7+} ions. Crystallographic, morphological and the functional groups of the pristine and irradiated samples were studied using glancing incident X-ray diffraction (GIXRD), scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy-attenuated total reflectance (FTIR-ATR) respectively. SEM reveals the creation of pores, along with an increase in porosity and cluster size on irradiation. Decrease in crystalline nature and crystallite size with an increase in ion fluence was observed from GIXRD patterns. The surface roughness and the wettability of the material were also enhanced, which could favour the cell–material interaction. The irradiated samples adsorbed significantly greater amount of proteins than pristine. Also, irradiation does not produce any toxic byproducts or leachants, and maintains the viability of 3T3 cells. The response of the irradiated samples towards biomedical applications was demonstrated by the improved antimicrobial activity, haemocompatibility and cytocompatibility. Swift heavy ion irradiation (SHI) could be an effective tool to modify and engineer the surface properties of the polymers to enhance the biocompatibility.

  14. Electrical properties of ion irradiated polypropylene films

    Indian Academy of Sciences (India)

    N L Singh; Anita Sharma; V Shrinet; A K Rakshit; D K Avasthi

    2004-06-01

    The effect of high-energy (50 MeV) Li3+ ion beam irradiation on polypropylene (PP) film has been studied in the fluence range 2.4 × 1012-1.5 × 1014 ions/cm2. The a.c. electrical properties of PP films were measured in the frequency range from 0.05–100 kHz, and at temperature range between 30 and 140°C. This study indicates two peaks at 60°C and 120°C with comparatively high magnitudes. There is an exponential increase in conductivity with log of frequency and the effect is significant at higher fluences. The loss factor (tan ) vs frequency plot suggests that PP film based capacitors may be useful below 10 kHz. The capacitance is constant over a wide temperature range up to 130°C. FTIR spectra of the PP films before and after irradiation indicate that intensity of C–H stretching vibration at 2900 cm-1 is modified. The presence of many new peaks with the increase of fluence suggests the formation of alkanes and alkynes which might be responsible for the observed changes in the dielectric and electrical properties of PP films.

  15. Studies of defects on ion irradiated diamond

    Energy Technology Data Exchange (ETDEWEB)

    Lai, P.F.; Prawer, S.; Spargo, A.E.C.; Bursill, L.A. [Melbourne Univ., Parkville, VIC (Australia). School of Physics

    1996-12-31

    It is known that diamond is amorphized or graphitized when irradiated above a critical dose. Above this critical dose, D{sub c}, the resistance R is found to drop very rapidly due to the formation of graphite regions which overlap at D{sub c} to form a semi-continuous electrically conducting pathway through the sample. One particularly interesting method of studying this transformation is electron energy-loss spectroscopy (EELS). Using EELS, the different phases of carbon can be identified and distinguished from each other using the extended energy-loss fine structure (EXELFS) of the core-loss part of the spectrum. EELS is a sensitive method for determining the electronic structure of small areas of a sample. In this paper, transmission electron microscopy (TEM) and EELS measurements of the ion irradiated diamond were combined in an attempt to correlate the microstructural nature of the ion-beam induced damage to the changes in the electrical and other properties. 7 refs., 1 tab., 2 figs.

  16. Chlorine diffusion in uranium dioxide under heavy ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Pipon, Y. [Universite Claude Bernard Lyon-1/Institut de Physique Nucleaire de Lyon (IPNL), 4, rue Enrico Fermi, 69622 Villeurbanne cedex (France) and Universite Claude Bernard Lyon-1, Institut Universitaire de Technologie (IUT A), 94, boulevard Niels Bohr, 69622 Villeurbanne cedex (France)]. E-mail: pipon@ipnl.in2p3.fr; Bererd, N. [Universite Claude Bernard Lyon-1/Institut de Physique Nucleaire de Lyon (IPNL), 4, rue Enrico Fermi, 69622 Villeurbanne cedex (France); Universite Claude Bernard Lyon-1, Institut Universitaire de Technologie (IUT A), 94, boulevard Niels Bohr, 69622 Villeurbanne cedex (France); Moncoffre, N. [Universite Claude Bernard Lyon-1/Institut de Physique Nucleaire de Lyon (IPNL), 4, rue Enrico Fermi, 69622 Villeurbanne cedex (France); Peaucelle, C. [Universite Claude Bernard Lyon-1/Institut de Physique Nucleaire de Lyon (IPNL), 4, rue Enrico Fermi, 69622 Villeurbanne cedex (France); Toulhoat, N. [Universite Claude Bernard Lyon-1/Institut de Physique Nucleaire de Lyon (IPNL), 4, rue Enrico Fermi, 69622 Villeurbanne cedex (France); Commissariat a l' Energie Atomique (CEA), DEN/Saclay, 91191 Gif sur Yvette cedex (France); Jaffrezic, H. [Universite Claude Bernard Lyon-1/Institut de Physique Nucleaire de Lyon (IPNL), 4, rue Enrico Fermi, 69622 Villeurbanne cedex (France); Raimbault, L. [Ecole des Mines de Paris, Centre de Geosciences, 35 rue Saint Honore, F-77305 Fontainebleau cedex (France); Sainsot, P. [Institut National des Sciences Appliquees de Lyon (INSA), UMR 5514, F-69621 Villeurbanne cedex (France); Carlot, G. [Commissariat a l' Energie Atomique (CEA), Centre de Cadarache, DEN/DEC/SESC/LLCC, 13108 Saint-Paul lez Durance (France)

    2007-04-15

    The radiation enhanced diffusion of chlorine in UO{sub 2} during heavy ion irradiation is studied. In order to simulate the behaviour of {sup 36}Cl, present as an impurity in UO{sub 2}, {sup 37}Cl has been implanted into the samples (projected range 200 nm). The samples were then irradiated with 63.5 MeV {sup 127}I at two fluxes and two temperatures and the chlorine distribution was analyzed by SIMS. The results show that, during irradiation, the diffusion of the implanted chlorine is enhanced and slightly athermal with respect to pure thermal diffusion. A chlorine gain of 10% accumulating near the surface has been observed at 510 K. This corresponds to the displacement of pristine chlorine from a region of maximum defect concentration. This behaviour and the mean value of the apparent diffusion coefficient found for the implanted chlorine, around 2.5 x 10{sup -14} cm{sup 2} s{sup -1}, reflect the high mobility of chlorine in UO{sub 2} during irradiation with fission products.

  17. Chlorine diffusion in uranium dioxide under heavy ion irradiation

    Science.gov (United States)

    Pipon, Y.; Bérerd, N.; Moncoffre, N.; Peaucelle, C.; Toulhoat, N.; Jaffrézic, H.; Raimbault, L.; Sainsot, P.; Carlot, G.

    2007-04-01

    The radiation enhanced diffusion of chlorine in UO2 during heavy ion irradiation is studied. In order to simulate the behaviour of 36Cl, present as an impurity in UO2, 37Cl has been implanted into the samples (projected range 200 nm). The samples were then irradiated with 63.5 MeV 127I at two fluxes and two temperatures and the chlorine distribution was analyzed by SIMS. The results show that, during irradiation, the diffusion of the implanted chlorine is enhanced and slightly athermal with respect to pure thermal diffusion. A chlorine gain of 10% accumulating near the surface has been observed at 510 K. This corresponds to the displacement of pristine chlorine from a region of maximum defect concentration. This behaviour and the mean value of the apparent diffusion coefficient found for the implanted chlorine, around 2.5 × 10-14 cm2 s-1, reflect the high mobility of chlorine in UO2 during irradiation with fission products.

  18. Rows of Dislocation Loops in Aluminium Irradiated by Aluminium Ions

    DEFF Research Database (Denmark)

    Henriksen, L.; Johansen, A.; Koch, J.

    1967-01-01

    Single-crystal aluminium specimens, irradiated with 50-keV aluminium ions, contain dislocation loops that are arranged in regular rows along <110 > directions. ©1967 The American Institute of Physics......Single-crystal aluminium specimens, irradiated with 50-keV aluminium ions, contain dislocation loops that are arranged in regular rows along directions. ©1967 The American Institute of Physics...

  19. Spectroscopic characterization of ion-irradiated multi-layer graphenes

    Energy Technology Data Exchange (ETDEWEB)

    Tsukagoshi, Akira [Graduate School of Engineering, University of Hyogo, Himeji, Hyogo 671-2280 (Japan); RIKEN SPring-8 Center, Sayo, Hyogo 679-5148 (Japan); Honda, Shin-ichi, E-mail: s-honda@eng.u-hyogo.ac.jp [Graduate School of Engineering, University of Hyogo, Himeji, Hyogo 671-2280 (Japan); RIKEN SPring-8 Center, Sayo, Hyogo 679-5148 (Japan); Osugi, Ryo [Graduate School of Engineering, University of Hyogo, Himeji, Hyogo 671-2280 (Japan); RIKEN SPring-8 Center, Sayo, Hyogo 679-5148 (Japan); Okada, Hiraku [Graduate School of Engineering, University of Hyogo, Himeji, Hyogo 671-2280 (Japan); Niibe, Masahito [Laboratory of Advanced Science and Technology for Industry, University of Hyogo, Kamigori, Hyogo 678-1205 (Japan); Terasawa, Mititaka [Laboratory of Advanced Science and Technology for Industry, University of Hyogo, Kamigori, Hyogo 678-1205 (Japan); RIKEN SPring-8 Center, Sayo, Hyogo 679-5148 (Japan); Hirase, Ryuji; Izumi, Hirokazu; Yoshioka, Hideki [Hyogo Prefectural Institute of Technology, Kobe 654-0037 (Japan); Niwase, Keisuke [Hyogo University of Teacher Education, Kato, Hyogo 673-1494 (Japan); Taguchi, Eiji [Research Center for Ultra-High Voltage Electron Microscopy, Osaka University, Ibaraki, Osaka 567-0047 (Japan); Lee, Kuei-Yi [Department of Electronic Engineering, National Taiwan University of Science and Technology, Taipei 106, Taiwan (China); Oura, Masaki [RIKEN SPring-8 Center, Sayo, Hyogo 679-5148 (Japan)

    2013-11-15

    Low-energy Ar ions (0.5–2 keV) were irradiated to multi-layer graphenes and the damage process, the local electronic states, and the degree of alignment of the basal plane, and the oxidation process upon ion irradiation were investigated by Raman spectroscopy, soft X-ray absorption spectroscopy (XAS) and in situ X-ray photoelectron spectroscopy (XPS). By Raman spectroscopy, we observed two stages similar to the case of irradiated graphite, which should relate to the accumulations of vacancies and turbulence of the basal plane, respectively. XAS analysis indicated that the number of sp{sup 2}-hybridized carbon (sp{sup 2}-C) atoms decreased after ion irradiation. Angle-resolved XAS revealed that the orientation parameter (OP) decreased with increasing ion energy and fluence, reflecting the turbulence of the basal plane under irradiation. In situ XPS shows the oxidation of the irradiated multi-layer graphenes after air exposure.

  20. Effects of heavy-ion irradiation on FeSe

    Science.gov (United States)

    Sun, Yue; Park, Akiyoshi; Pyon, Sunseng; Tamegai, Tsuyoshi; Kambara, Tadashi; Ichinose, Ataru

    2017-03-01

    We report the effects of heavy-ion irradiation on FeSe single crystals by irradiating uranium up to a dose-equivalent matching field of Bϕ=16 T. Almost continuous columnar defects along the c axis with a diameter of ˜10 nm are confirmed by high-resolution transmission electron microscopy. Tc is found to be suppressed by introducing columnar defects at a rate of d Tc/d Bϕ˜-0.29 K/T, which is much larger than those observed in iron pnictides. This unexpected large suppression of Tc in FeSe is discussed in relation to the large diameter of the columnar defects as well as its unique band structure with a remarkably small Fermi energy. The critical current density is first dramatically enhanced with irradiation reaching a value over ˜2 ×105A /cm2 (˜5 times larger than that of the pristine sample) at 2 K (self-field) with Bϕ=2 T, then gradually suppressed with increasing Bϕ. The δ l pinning associated with charge-carrier mean-free-path fluctuations and the δ Tc pinning associated with spatial fluctuations of the transition temperature are found to coexist in the pristine FeSe, while the irradiation increases the contribution from δ l pinning and makes it dominant over Bϕ=4 T.

  1. Effect of low energy electron irradiation on DNA damage by Cu{sup 2+} ion

    Energy Technology Data Exchange (ETDEWEB)

    Noh, Hyung Ah; Cho, Hyuck [Dept. of Physics, Chungnam National University, Daejeon (Korea, Republic of); Park, Yeun Soo [Plasma Technology Research Center, National Fusion Research Institute, Gunsan (Korea, Republic of)

    2017-03-15

    The combined effect of the low energy electron (LEE) irradiation and Cu{sup 2+} ion on DNA damage was investigated. Lyophilized pBR322 plasmid DNA films with various concentrations (1–15 mM) of Cu{sup 2+} ion were independently irradiated by monochromatic LEEs with 5 eV. The types of DNA damage, single strand break (SSB) and double strand break (DSB), were separated and quantified by gel electrophoresis. Without electron irradiation, DNA damage was slightly increased with increasing Cu ion concentration via Fenton reaction. LEE-induced DNA damage, with no Cu ion, was only 6.6% via dissociative electron attachment (DEA) process. However, DNA damage was significantly increased through the combined effect of LEE-irradiation and Cu ion, except around 9 mM Cu ion. The possible pathways of DNA damage for each of these different cases were suggested. The combined effect of LEE-irradiation and Cu ion is likely to cause increasing dissociation after elevated transient negative ion state, resulting in the enhanced DNA damage. For the decrease of DNA damage at around 9-mM Cu ion, it is assumed to be related to the structural stabilization due to DNA inter- and intra-crosslinks via Cu ion.

  2. Biological effect of penetration controlled irradiation with ion beams

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, Atsushi; Shimizu, Takashi; Kikuchi, Masahiro; Kobayashi, Yasuhiko; Watanabe, Hiroshi [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment; Yamashita, Takao

    1997-03-01

    To investigate the effect of local irradiation with ion beams on biological systems, technique for penetration controlled irradiation has been established. The range in a target was controlled by changing the distance from beam window in the atmosphere, and could be controlled linearly up to about 31 {mu}m in biological material. In addition, the effects of the penetration controlled irradiations with 1.5 MeV/u C and He ions were examined using tobacco pollen. The increased frequency of leaky pollen produced by ion beams suggests that the efficient pollen envelope damages would be induced at the range-end of ion beams. (author)

  3. Influence of the irradiation temperature on the surface structure and physical/chemical properties of Ar ion-irradiated bulk metallic glasses

    Energy Technology Data Exchange (ETDEWEB)

    Menéndez, E., E-mail: Enric.MenendezDalmau@fys.kuleuven.be [KU Leuven, Instituut voor Kern-en Stralingsfysica, Celestijnenlaan 200 D, 3001 Leuven (Belgium); Hynowska, A.; Fornell, J.; Suriñach, S. [Departament de Física, Facultat de Ciències, Universitat Autònoma de Barcelona, E-08193 Bellaterra (Spain); Montserrat, J. [Institut de Microelectrònica de Barcelona (IMB-CNM), CSIC, Campus Universitat Autònoma Barcelona, E-08193 Bellaterra (Spain); Temst, K.; Vantomme, A. [KU Leuven, Instituut voor Kern-en Stralingsfysica, Celestijnenlaan 200 D, 3001 Leuven (Belgium); Baró, M.D. [Departament de Física, Facultat de Ciències, Universitat Autònoma de Barcelona, E-08193 Bellaterra (Spain); García-Lecina, E. [Surfaces Division, IK4-CIDETEC, Parque Tecnológico de San Sebastián, E-20009 Donostia (Spain); Pellicer, E., E-mail: Eva.Pellicer@uab.cat [Departament de Física, Facultat de Ciències, Universitat Autònoma de Barcelona, E-08193 Bellaterra (Spain); Sort, J., E-mail: Jordi.Sort@uab.cat [Institució Catalana de Recerca i Estudis Avançats (ICREA) and Departament de Física, Universitat Autònoma de Barcelona, E-08193 Bellaterra (Spain)

    2014-10-15

    Highlights: • Ion irradiation is performed on bulk metallic glasses at 300 K and close to T{sub g}. • Nanocrystallization is observed after high-temperature irradiation. • The mechanical properties are enhanced after the irradiation procedures. • Corrosion resistance is improved after irradiation close to T{sub g}. - Abstract: Surface treatments using multiple Ar ion irradiation processes with a maximum energy and fluence of 200 keV and 1 × 10{sup 16} ions/cm{sup 2}, respectively, have been performed on two different metallic glasses: Zr{sub 55}Cu{sub 28}Al{sub 10}Ni{sub 7} and Ti{sub 40}Zr{sub 10}Cu{sub 38}Pd{sub 12}. Analogous irradiation procedures have been carried out at room temperature (RT) and at T = 620 K (≈0.9 T{sub g}, where T{sub g} denotes the glass transition). The structure, mechanical behavior, wettability and corrosion resistance of the irradiated alloys have been compared with the properties of the as-cast and annealed (T = 620 K) non-irradiated specimens. While ion irradiation at RT does not significantly alter the amorphous structure of the alloys, ion irradiation close to T{sub g} promotes decomposition/nanocrystallization. Consequently, the hardness (H) and reduced Young’s modulus (E{sub r}) decrease after irradiation at RT but they both increase after irradiation at 620 K. While annealing close to T{sub g} increases the hydrophobicity of the samples, irradiation induces virtually no changes in the contact angle when comparing with the as-cast state. Concerning the corrosion resistance, although not much effect is found after irradiation at RT, an improvement is observed after irradiation at 620 K, particularly for the Ti-based alloy. These results are of practical interest in order to engineer appropriate surface treatments based on ion irradiation, aimed at specific functional applications of bulk metallic glasses.

  4. Modification on graphite due to helium ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Dutta, N.J.; Mohanty, S.R., E-mail: smrutirm@yahoo.com; Buzarbaruah, N.

    2016-07-29

    This paper studies the influence of helium ion irradiation on morphological and structural properties of graphite samples. The helium ions emanated from a plasma focus device have been used to irradiate graphite samples by varying the number of ion pulses. The effect of radiation induced changes in morphology and structure are examined by using optical microscopy, atomic force microscopy, transmission electron microscopy along with selected area electron diffraction and x-ray diffraction. A distinct change in the surface topography is marked in the case of the ion irradiated samples when viewed under the optical microscope. The micrographs of the ion irradiated samples confirm mostly rounded and sparely elongated type of structures arising due to intense melting and local ablation accompanied with ejection of graphite melts that depends upon the ion fluence. The atomic force microscopy images also reveal the formation of globules having sizes ∼50–200 nm which are the agglomeration of small individual clusters. Transmission electron micrographs of the ion irradiated samples furnish that the diameter of these individual small clusters are ∼10.4 nm. Moreover, selected area electron diffraction patterns corroborate that the ion irradiated sample retains its crystalline nature, even after exposure to larger helium ion pulses. It is noticed from the x-ray diffraction patterns that some new phases are developed in the case of ion irradiated sample. - Highlights: • Used an ingenious helium ion source to study irradiation induced transformation on graphite. • OM, AFM and TEM analyses confirm the formation mostly rounded structures. • SAED patterns confirm the retention of crystallinity of graphite even after exposure to larger helium ion fluences. • XRD patterns confirm the development of new peaks that indicate structural rearrangement.

  5. Structural and electrical properties of swift heavy ion beam irradiated Co/Si interface

    Indian Academy of Sciences (India)

    Garima Agarwal; Ankur Jain; Shivani Agarwal; D Kabiraj; I P Jain

    2006-04-01

    Synthesis of swift heavy ion induced metal silicide is a new advancement in materials science research. We have investigated the mixing at Co/Si interface by swift heavy ion beam induced irradiation in the electronic stopping power regime. Irradiations were undertaken at room temperature using 120 MeV Au ions at the Co/Si interface for investigation of ion beam mixing at various doses: 8 × 1012, 5 × 1013 and 1 × 1014 cm-2. Formation of different phases of cobalt silicide is identified by the grazing incidence X-ray diffraction (GIXRD) technique, which shows enhancement of intermixing and silicide formation as a result of irradiation. – characteristics at Co/Si interface were undertaken to understand the irradiation effect on conduction mechanism at the interface.

  6. Modifying the morphology and magnetic properties of magnetite nanoparticles using swift heavy ion irradiation

    Science.gov (United States)

    Gokhale, Shubha; Lamba, Subhalakshmi; Kumari, Neha; Singh, Bhupendra; Avasthi, D. K.; Kulkarni, S. K.

    2014-08-01

    Magnetite (Fe3O4) nanospheres of ˜8-11 nm diameter synthesized using a chemical co-precipitation method were deposited as thin films on different substrates using spin coating. The thin films were irradiated with Ag ions at 100 MeV energy. Comparison of unirradiated, as synthesized Fe3O4 nanoparticulate thin film and ion irradiated film shows that irradiation causes dramatic changes in the morphology, structure and magnetic properties. Monte Carlo simulations carried out on this system indicate that the origin of the changes in the magnetic properties lies in the enhanced magnetic anisotropy energy density and reorientation of magnetic easy axis.

  7. Silver ion beam irradiation effects on poly(lactide-co-glycolide) (PLGA)/clay nanocomposites

    Energy Technology Data Exchange (ETDEWEB)

    Kaur, Manpreet; Singh, Surinder [Guru Nanak Dev University, Department of Physics, Amritsar (India); Mehta, Rajeev [Thapar University, Department of Chemical Engineering, Patiala (India)

    2014-12-15

    Swift heavy ions induced modification of thin films of blends of poly(lactide-co-glycolide) (PLGA) (50:50) with organically modified nanoclay (Cloisite {sup registered} 30B) has been studied, using optical, structural and surface morphological analysis. Presence of nanoclay is found to enhance the properties of this degradable copolymer by reducing the rate of degradation even at high irradiation fluence. Optical and structural analysis of the polymer nanocomposites suggests that both the cross-linking and chain scission phenomenon are caused by swift heavy ion irradiation. XRD measurements show intercalation of PLGA in the clay galleries. Surface morphology of a nanocomposite indicates significant changes after irradiation at various fluences. (orig.)

  8. Swift Heavy Ion Irradiation Effects on NPN rf Power Transistors

    Science.gov (United States)

    Pushpa, N.; Prakash, A. P. Gnana; Gupta, S. K.; Revannasiddaiah, D.

    2011-07-01

    The dc characteristics of NPN rf power transistors were studied systematically before and after irradiation by 50 MeV Li3+ ions, 100 MeV F8+ ions and 140 MeV Si10+ ions in the dose range of 100 krad to 100 Mrad. The transistor parameters such as excess base current (ΔIB = IBpost-IBpre), dc current gain (hFE), and collector-saturation current (ICSat) were determined before and after irradiation. The base current (IB) was found to increase significantly after ion irradiation and this in turn decreases the hFE of the transistors. Further, the output characteristics of the irradiated devices exhibit the decrease in the collector current at the saturation region (ICSat) with increase of ion dose.

  9. Anti-biofilm activity of Fe heavy ion irradiated polycarbonate

    Science.gov (United States)

    Joshi, R. P.; Hareesh, K.; Bankar, A.; Sanjeev, Ganesh; Asokan, K.; Kanjilal, D.; Dahiwale, S. S.; Bhoraskar, V. N.; Dhole, S. D.

    2016-10-01

    Polycarbonate (PC) polymers were investigated before and after high energy heavy ion irradiation for anti-bacterial properties. These PC films were irradiated by Fe heavy ions with two energies, viz, 60 and 120 MeV, at different fluences in the range from 1 × 1011 ions/cm2 to 1 × 1013 ions/cm2. UV-Visible spectroscopic results showed optical band gap decreased with increase in ion fluences due to chain scission mainly at carbonyl group of PC which is also corroborated by Fourier transform infrared spectroscopic results. X-ray diffractogram results showed decrease in crystallinity of PC after irradiation which leads to decrease in molecular weight. This is confirmed by rheological studies and also by differential scanning calorimetric results. The irradiated PC samples showed modification in their surfaces prevents biofilm formation of human pathogen, Salmonella typhi.

  10. Differential effects of irradiation with carbon ions and x-rays on macrophage function.

    Science.gov (United States)

    Conrad, Sandro; Ritter, Sylvia; Fournier, Claudia; Nixdorff, Kathryn

    2009-05-01

    Macrophages are potent elicitors of inflammatory reactions that can play both positive and negative roles in radiotherapy. While several studies have investigated the effects of X-rays or gamma-rays on macrophages, virtually no work has been done on the responses of these cells to irradiation with carbon ions. Investigations into the effects of carbon ion irradiation are of particular interest in light of the fact that this type of radiation is being used increasingly for cancer therapy. In the present investigation we compared the effects of 250 kV X-rays with those of 9.8 MeV/u carbon ions on RAW 264.7 macrophages over a wide range of radiation doses. Macrophage functions including vitality, phagocytic activity, production of the proinflammatory cytokines IL-1beta and TNFalpha and production of nitric oxide (NO) were measured. In comparison to lymphocytes and fibroblasts, macrophages showed only a small decrease in vitality after irradiation with either X-rays or carbon ions. Proinflammatory cytokines and NO were induced in macrophages by LPS but not by irradiation alone. X-rays or carbon ions had little modulating effect on LPS-induced TNFalpha production. However, LPS-induced NO increased in a dose dependent manner up to 6-fold after carbon ion irradiation, while X-ray irradiation did not have this effect. Carbon ion irradiation mediated a concomitant decrease in IL-1beta production. Carbon ions also had a greater effect than X-rays in enhancing the phagocytic activity of macrophages. These results underscore the greater potential of carbon ion irradiation with regard to radiobiological effectiveness.

  11. Surface modification of Zr-based bulk amorphous alloys by using ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Iqbal, M., E-mail: miqbalchishti@yahoo.com [Physics Division, Pakistan Institute of Nuclear Science and Technology (PINSTECH), P.O. Nilore, Islamabad, 45650 (Pakistan); Qayyum, A.; Akhter, J.I. [Physics Division, Pakistan Institute of Nuclear Science and Technology (PINSTECH), P.O. Nilore, Islamabad, 45650 (Pakistan)

    2011-02-10

    Research highlights: > Ion irradiations of two multicomponent bulk amorphous alloys have been done. Ion irradiation produced crystalline phases in the amorphous matrix due to which mechanical properties enhanced. Considerable increase in hardness and elastic modulus was observed. The results are verified, authentic and confirmed. - Abstract: Surfaces of the [Zr{sub 0.65}Cu{sub 0.18}Ni{sub 0.09}Al{sub 0.08}]{sub 98}M{sub 2} (M = Er and Gd) bulk amorphous alloys were modified by irradiation with energetic singly charged argon (Ar{sup +}) ions. Samples of both the alloys were irradiated with 2.17 x 10{sup 17} argon ions of 10 keV energy. As cast and ion irradiated samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). Mechanical properties like Vicker's hardness, nanohardness, elastic modulus and elastic recovery were measured. Considerable increase in elastic modulus and hardness was observed because of ion irradiation in these alloys. The ion irradiated samples of the [Zr{sub 0.65}Cu{sub 0.18}Ni{sub 0.09}Al{sub 0.08}]{sub 98}Er{sub 2} alloy showed better properties as compared to [Zr{sub 0.65}Cu{sub 0.18}Ni{sub 0.09}Al{sub 0.08}]{sub 98}Gd{sub 2} alloy. CuZr{sub 2} phase was detected in ion irradiated alloys by XRD and confirmed by EDS. The range of Ar{sup +} ions was found to be approximately 9.3 {+-} 5.4 nm in both alloys.

  12. Effect of irradiation temperature on microstructural changes in self-ion irradiated austenitic stainless steel

    Science.gov (United States)

    Jin, Hyung-Ha; Ko, Eunsol; Lim, Sangyeob; Kwon, Junhyun; Shin, Chansun

    2017-09-01

    We investigated the microstructural and hardness changes in austenitic stainless steel after Fe ion irradiation at 400, 300, and 200 °C using transmission electron microscopy (TEM) and nanoindentation. The size of the Frank loops increased and the density decreased with increasing irradiation temperature. Radiation-induced segregation (RIS) was detected across high-angle grain boundaries, and the degree of RIS increases with increasing irradiation temperature. Ni-Si clusters were observed using high-resolution TEM in the sample irradiated at 400 °C. The results of this work are compared with the literature data of self-ion and proton irradiation at comparable temperatures and damage levels on stainless steels with a similar material composition with this study. Despite the differences in dose rate, alloy composition and incident ion energy, the irradiation temperature dependence of RIS and the size and density of radiation defects followed the same trends, and were very comparable in magnitude.

  13. Ionoluminescence of fused silica under swift ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Saavedra, R. [Fusion Materials Research Unit, National Fusion Laboratory, CIEMAT, Av Complutense, 40, 28040 Madrid (Spain); Jiménez-Rey, D. [Fusion Materials Research Unit, National Fusion Laboratory, CIEMAT, Av Complutense, 40, 28040 Madrid (Spain); Centre for Micro Analysis of Materials, Universidad Autónoma de Madrid, Cantoblanco, 28049 Madrid (Spain); Martin, P.; Vila, R. [Fusion Materials Research Unit, National Fusion Laboratory, CIEMAT, Av Complutense, 40, 28040 Madrid (Spain)

    2016-09-01

    Highlights: • Irradiation with He{sup +} ions (lowest stopping power) shows highest luminescence. • Silica with highest OH content presents the lowest blue luminescence. • Electronic excitation was the predominant process of energy transfer. • Surface cracks were observed in Si or O irradiated samples at low fluence. • Blue IL maximum for O and Si irradiated samples is related to structural changes. - Abstract: Ion beam induced luminescence spectra have been in-situ recorded during He{sup +} (2.5 MeV), O{sup 4+} (13.5 MeV) and Si{sup 4+} (24.4 MeV) irradiations for three vitreous silica grades with different OH content (KU1, KS-4V and Infrasil 301). Remarkable changes in the ionoluminescence spectra of the three silica grades were observed for low ion fluences. He{sup +} irradiated samples exhibited higher luminescence than equivalent ones irradiated with heavier O{sup 4+} and Si{sup 4+} ions. KU1 samples with the highest OH content showed the lowest blue luminescence. Blue luminescence maximum during ion irradiations with O{sup 4+} and Si{sup 4+} ions is correlated with structural changes.

  14. Anti-biofilm activity of Fe heavy ion irradiated polycarbonate

    Energy Technology Data Exchange (ETDEWEB)

    Joshi, R.P. [Department of Physics, Savitribai Phule Pune University, Pune 411007 (India); Hareesh, K., E-mail: appi.2907@gmail.com [Department of Physics, Savitribai Phule Pune University, Pune 411007 (India); Bankar, A. [Department of Microbiology, Waghire College, Pune 412301 (India); Sanjeev, Ganesh [Microtron Centre, Department of Studies in Physics, Mangalore University, Mangalore 574166 (India); Asokan, K.; Kanjilal, D. [Inter University Accelerator Centre, Arun Asaf Ali Marg, New Delhi 110067 (India); Dahiwale, S.S.; Bhoraskar, V.N. [Department of Physics, Savitribai Phule Pune University, Pune 411007 (India); Dhole, S.D., E-mail: sanjay@physics.unipune.ac.in [Department of Physics, Savitribai Phule Pune University, Pune 411007 (India)

    2016-10-01

    Highlights: • PC films were irradiated by 60 and 120 MeV Fe ions. • Irradiated PC films showed changes in its physical and chemical properties. • Irradiated PC also showed more anti-biofilm activity compared to pristine PC. - Abstract: Polycarbonate (PC) polymers were investigated before and after high energy heavy ion irradiation for anti-bacterial properties. These PC films were irradiated by Fe heavy ions with two energies, viz, 60 and 120 MeV, at different fluences in the range from 1 × 10{sup 11} ions/cm{sup 2} to 1 × 10{sup 13} ions/cm{sup 2}. UV-Visible spectroscopic results showed optical band gap decreased with increase in ion fluences due to chain scission mainly at carbonyl group of PC which is also corroborated by Fourier transform infrared spectroscopic results. X-ray diffractogram results showed decrease in crystallinity of PC after irradiation which leads to decrease in molecular weight. This is confirmed by rheological studies and also by differential scanning calorimetric results. The irradiated PC samples showed modification in their surfaces prevents biofilm formation of human pathogen, Salmonella typhi.

  15. High-fluence hyperthermal ion irradiation of gallium nitride surfaces at elevated temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Finzel, A.; Gerlach, J.W., E-mail: juergen.gerlach@iom-leipzig.de; Lorbeer, J.; Frost, F.; Rauschenbach, B.

    2014-10-30

    Highlights: • Irradiation of gallium nitride films with hyperthermal nitrogen ions. • Surface roughening at elevated sample temperatures was observed. • No thermal decomposition of gallium nitride films during irradiation. • Asymmetric surface diffusion processes cause local roughening. - Abstract: Wurtzitic GaN films deposited on 6H-SiC(0001) substrates by ion-beam assisted molecular-beam epitaxy were irradiated with hyperthermal nitrogen ions with different fluences at different substrate temperatures. In situ observations with reflection high energy electron diffraction showed that during the irradiation process the surface structure of the GaN films changed from two dimensional to three dimensional at elevated temperatures, but not at room temperature. Atomic force microscopy revealed an enhancement of nanometric holes and canyons upon the ion irradiation at higher temperatures. The roughness of the irradiated and heated GaN films was clearly increased by the ion irradiation in accordance with x-ray reflectivity measurements. A sole thermal decomposition of the films at the chosen temperatures could be excluded. The results are discussed taking into account temperature dependent sputtering and surface uphill adatom diffusion as a function of temperature.

  16. Positron annihilation Doppler broadening spectroscopy study on Fe-ion irradiated NHS steel

    Science.gov (United States)

    Zhu, Huiping; Wang, Zhiguang; Gao, Xing; Cui, Minghuan; Li, Bingsheng; Sun, Jianrong; Yao, Cunfeng; Wei, Kongfang; Shen, Tielong; Pang, Lilong; Zhu, Yabin; Li, Yuanfei; Wang, Ji; Song, Peng; Zhang, Peng; Cao, Xingzhong

    2015-02-01

    In order to study the evolution of irradiation-induced vacancy-type defects at different irradiation fluences and temperatures, a new type of ferritic/martensitic (F/M) steel named NHS (Novel High Silicon) was irradiated by 3.25 MeV Fe-ion at room temperature and 723 K to fluences of 4.3 × 1015 and 1.7 × 1016 ions/cm2. After irradiation, vacancy-type defects were investigated with variable-energy positron beam Doppler broadening spectra. Energetic Fe-ions produced a large number of vacancy-type defects in the NHS steel, but one single main type of vacancy-type defect was observed in both unirradiated and irradiated samples. The concentration of vacancy-type defects decreased with increasing temperature. With the increase of irradiation fluence, the concentration of vacancy-type defects increased in the sample irradiated at RT, whereas for the sample irradiated at 723 K, it decreased. The enhanced recombination between vacancies and excess interstitial Fe atoms from deeper layers, and high diffusion rate of self-interstitial atoms further improved by diffusion via grain boundary and dislocations at high temperature, are thought to be the main reasons for the reversed trend of vacancy-type defects between the samples irradiated at RT and 723 K.

  17. Failure Analysis of Heavy-Ion-Irradiated Schottky Diodes

    Science.gov (United States)

    Casey, Megan C.; Lauenstein, Jean-Marie; Wilcox, Edward P.; Topper, Alyson D.; Campola, Michael J.; Label, Kenneth A.

    2017-01-01

    In this work, we use high- and low-magnitude optical microscope images, infrared camera images, and scanning electron microscope images to identify and describe the failure locations in heavy-ion-irradiated Schottky diodes.

  18. Recent progress in molecule modification with heavy ion beam irradiation

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The research into heavy ion beam biology started in the 1960s, and so far it has become an important interdisciplinary study. Heavy ion beam is more suitable for molecule modification than other sorts of radiation, for it has many superiorities such as the energy transfer effect and the mass deposition effect. Molecule modification with heavy ion beam irradiation can be applied to developing new medicines and their precursors, genetic engineering, protein engi neering, outer space radiobiology, etc. Retrospect and prospect of the research and development of molecule modifica tion with heavy ion beam irradiation are given.

  19. Ion irradiation testing of Improved Accident Tolerant Cladding Materials

    Energy Technology Data Exchange (ETDEWEB)

    Anderoglu, Osman [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Tesmer, Joseph R. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Maloy, Stuart A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2014-01-14

    This report summarizes the results of ion irradiations conducted on two FeCrAl alloys (named as ORNL A&B) for improving the accident tolerance of LWR nuclear fuel cladding. After irradiation with 1.5 MeV protons to ~0.5 to ~1 dpa and 300°C nanoindentations were performed on the cross-sections along the ion range. An increase in hardness was observed in both alloys. Microstructural analysis shows radiation induced defects.

  20. Physical and biological properties of the ion beam irradiated PMMA-based composite films

    Science.gov (United States)

    Shanthini, G. M.; Martin, Catherine Ann; Sakthivel, N.; Veerla, Sarath Chandra; Elayaraja, K.; Lakshmi, B. S.; Asokan, K.; Kanjilal, D.; Kalkura, S. Narayana

    2015-02-01

    Polymethyl methacrylate (PMMA) and PMMA-hydroxyapatite (PMMA-HAp) composite films, prepared by the solvent evaporation method were irradiated with 100 MeV Si7+ ions. Crystallographic, morphological and the functional groups of the pristine and irradiated samples were studied using glancing incident X-ray diffraction (GIXRD), scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy-attenuated total reflectance (FTIR-ATR) respectively. SEM reveals the creation of pores, along with an increase in porosity and cluster size on irradiation. Decrease in crystalline nature and crystallite size with an increase in ion fluence was observed from GIXRD patterns. The surface roughness and the wettability of the material were also enhanced, which could favour the cell-material interaction. The irradiated samples adsorbed significantly greater amount of proteins than pristine. Also, irradiation does not produce any toxic byproducts or leachants, and maintains the viability of 3T3 cells. The response of the irradiated samples towards biomedical applications was demonstrated by the improved antimicrobial activity, haemocompatibility and cytocompatibility. Swift heavy ion irradiation (SHI) could be an effective tool to modify and engineer the surface properties of the polymers to enhance the biocompatibility.

  1. Highly sensitive urea sensing with ion-irradiated polymer foils

    Energy Technology Data Exchange (ETDEWEB)

    Fink, Dietmar, E-mail: fink@daad-alumni.de [Departamento de Fisica, Universidad Autonoma Metropolitana-Iztapalapa, P.O. Box 55-534, 09340 Mexico, D.F. (Mexico); Nuclear Physics Institute, Academy of Sciences of the Czech Republic, 250 68 Rez (Czech Republic); Munoz Hernandez, Gerardo [Departamento de Fisica, Universidad Autonoma Metropolitana-Iztapalapa, P.O. Box 55-534, 09340 Mexico, D.F. (Mexico); Division de Ciencias Naturales e Ingenieria, Universidad Autonoma Metropolitana-Cuajimalpa, Pedro Antonio de los Santos 84, Col. Sn. Miguel Chapultepec, C.P. 11850, Mexico, D.F. (Mexico); Alfonta, Lital, E-mail: alfontal@bgu.ac.il [Avram and Stella Goldstein-Goren Department of Biotechnology Engineering, Ben-Gurion University of the Negev, P.O. Box 653, Beer-Sheva 84105 (Israel)

    2012-02-15

    Recently we prepared urea-sensors by attaching urease to the inner walls of etched ion tracks within thin polymer foil. Here, alternative track-based sensor configurations are examined where the enzyme remained in solution. The conductivities of systems consisting of two parallel irradiated polymer foils and confining different urea/urease mixtures in between were examined. The correlations between conductivity and urea concentration differed strongly for foils with unetched and etched tracks, which points at different sensing mechanisms - tentatively attributed to the adsorption of enzymatic reaction products on the latent track entrances and to the enhanced conductivity of reaction product-filled etched tracks, respectively. All examined systems enable in principle, urea sensing. They point at the possibility of sensor cascade construction for more sensitive or selective sensor systems.

  2. Morphological study of borosilicate glass surface irradiated by heavy ions

    Energy Technology Data Exchange (ETDEWEB)

    Wang, T. S.; Du, X.; Yuan, W.; Duan, B. H.; D. Zhang, J.; Chen, L.; Peng, H. B.; Yang, D.; Zhang, G. F.; Zhu, Z. H.

    2016-11-01

    Borosilicate glass is a candidate material for radiation waste formation and other optical applications in various fields. To understand the radiation effect of borosilicate glass, heavy ion (Arq+, Krq+ and Xeq+) irradiations were used to simulate the alpha and recoiled nuclei irradiations in this study. The surface morphology of glass has been compared to ion irradiation doses and ion energies. The surface topography evolution of irradiated samples is characterized by optical microscopy, atomic force microscopy (AFM), transmission electron microscopy (TEM) and secondary ion mass spectrometry (SIMS). Micro-bumps are observed on the sample surface after irradiationwith 5 MeV Xeq+ over 5 × 1013 ions·cm-2. The size and density of the bumps increaseswith increasing irradiation dose. At a lowdose, bumps are on the nanometer (nm) scale and rather rare.While the dose is higher than 9 × 1015 ions·cm-2, the size of bumps is on the scale of a few microns, and the density is saturated. However, the height of the bumps increases froma fewnmto over 150nmwith further irradiation. The distribution of micro-bumps is nearly homogeneous. The bumps are condensed and swell up, and there is no crystallized structure according to the TEMdiffraction pattern. Elementmigration and concentrations are observedwith SIMS imaging. The arrayed micro-bumps are a new finding, and they might be used to change the surface properties. Bump formation is caused by phase separation, and volume swelling is induced by ion irradiation.

  3. Molecular characterization of microbial mutations induced by ion beam irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Ichida, Hiroyuki [Graduate School of Science and Technology, Chiba University, Matsudo, Chiba 271-8510 (Japan); Accelerator Applications Research Group, Nishina Center for Accelerator-Based Science, RIKEN, Wako, Saitama 351-0198 (Japan)], E-mail: ichida@riken.jp; Matsuyama, Tomoki [Cellular Biochemistry Laboratory, Discovery Research Institute, RIKEN, Wako, Saitama 351-0198 (Japan); Ryuto, Hiromichi [Accelerator Operation Group, Nishina Center for Accelerator-Based Science, RIKEN, Wako, Saitama 351-0198 (Japan); Hayashi, Yoriko [Accelerator Applications Research Group, Nishina Center for Accelerator-Based Science, RIKEN, Wako, Saitama 351-0198 (Japan); Fukunishi, Nobuhisa [Accelerator Operation Group, Nishina Center for Accelerator-Based Science, RIKEN, Wako, Saitama 351-0198 (Japan); Abe, Tomoko [Accelerator Applications Research Group, Nishina Center for Accelerator-Based Science, RIKEN, Wako, Saitama 351-0198 (Japan); Koba, Takato [Graduate School of Science and Technology, Chiba University, Matsudo, Chiba 271-8510 (Japan)

    2008-03-01

    A positive selection system for gene disruption using a sucrose-sensitive transgenic rhizobium was established and used for the molecular characterization of mutations induced by ion beam irradiations. Single nucleotide substitutions, insertions, and deletions were found to occur in the sucrose sensitivity gene, sacB, when the reporter line was irradiated with highly accelerated carbon and iron ion beams. In all of the insertion lines, fragments of essentially the same sequence and of approximately 1188 bp in size were identified in the sacB regions. In the deletion lines, iron ions showed a tendency to induce larger deletions than carbon ions, suggesting that higher LET beams cause larger deletions. We found also that ion beams, particularly 'heavier' ion beams, can produce single gene disruptions and may present an effective alternative to transgenic approaches.

  4. Erosion of Copper Target Irradiated by Ion Beam

    CERN Document Server

    Polosatkin, S V; Grishnyaev, E S; Konstantinov, S G; Shoshin, A A

    2012-01-01

    Erosion of copper target irradiated by deuterium ion beam with ultimate fluence is studied. The target originally destined for neutron generation represents bulk copper substrate covered by 3-\\mum titanium layer. The target was irradiated by deuterium ion beam generated in Bayard-Alpert type ion source with energy of ions 17.5 keV/nuclear. Maximal fluence in the center of the target achieves 2.5x10^23atoms/cm^2. Measurements of the profile of irradiated target and estimation of fluence shows that physical sputtering is a dominating process that determines the target erosion Most interesting feature is growth of \\mum-size tadpole-shaped structures, localized in the cracks of the surface. RFA analysis of these structures showed extremely large (up to 60%at.) carbon content.

  5. Positron annihilation Doppler broadening spectroscopy study on Fe-ion irradiated NHS steel

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Huiping [Institute of Modern Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Wang, Zhiguang, E-mail: zhgwang@impcas.ac.cn [Institute of Modern Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Gao, Xing; Cui, Minghuan; Li, Bingsheng; Sun, Jianrong; Yao, Cunfeng; Wei, Kongfang; Shen, Tielong; Pang, Lilong; Zhu, Yabin [Institute of Modern Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Li, Yuanfei; Wang, Ji [Institute of Modern Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); University of Lanzhou, Lanzhou 730000 (China); Song, Peng [Institute of Modern Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Zhang, Peng; Cao, Xingzhong [Institute of High Energy Physics, Chinese Academy of Sciences, Beijing 100049 (China)

    2015-02-01

    Highlights: • NHS steel was irradiated by 3.25 MeV Fe ions to different fluences at room temperature and 723 K. • The evolution of vacancy type defects is studied through positron annihilation spectroscopy. • The concentration gradient of SIA can induce the decrease of S value with increasing fluence at high temperature. - Abstract: In order to study the evolution of irradiation-induced vacancy-type defects at different irradiation fluences and temperatures, a new type of ferritic/martensitic (F/M) steel named NHS (Novel High Silicon) was irradiated by 3.25 MeV Fe-ion at room temperature and 723 K to fluences of 4.3 × 10{sup 15} and 1.7 × 10{sup 16} ions/cm{sup 2}. After irradiation, vacancy-type defects were investigated with variable-energy positron beam Doppler broadening spectra. Energetic Fe-ions produced a large number of vacancy-type defects in the NHS steel, but one single main type of vacancy-type defect was observed in both unirradiated and irradiated samples. The concentration of vacancy-type defects decreased with increasing temperature. With the increase of irradiation fluence, the concentration of vacancy-type defects increased in the sample irradiated at RT, whereas for the sample irradiated at 723 K, it decreased. The enhanced recombination between vacancies and excess interstitial Fe atoms from deeper layers, and high diffusion rate of self-interstitial atoms further improved by diffusion via grain boundary and dislocations at high temperature, are thought to be the main reasons for the reversed trend of vacancy-type defects between the samples irradiated at RT and 723 K.

  6. Characterization of swift heavy ion irradiation damage in ceria

    Energy Technology Data Exchange (ETDEWEB)

    Yablinsky, Clarissa; Devanathan, Ram; Pakarinen, Janne; Gan, Jian; Severin, Daniel; Trautmann, Christina; Allen, T. R.

    2015-05-14

    We have examined microstructural evolution in irradiated ceria (CeO2) using swift heavy ion irradiation, electron microscopy, and atomistic simulation. CeO2, a UO2 fuel surrogate, was irradiated with gold ions at an energy of 1 GeV to fluences up to 1x1014 ions/cm2. Transmission electron microscopy accompanied by electron energy loss spectroscopy showed that the ion tracks were of similar size at all fluences, and that there was no chemical change in the ion track core. Classical molecular dynamics simulations of thermal spikes in CeO2 with energy deposition of 12 and 36 keV/nm show damage consisting of isolated point defects at the lower energy and defect clusters at 36 keV/nm, with no amorphization at either energy. Inferences are drawn from modeling about density changes in the ion track and the formation of interstitial loops that shed light on features observed by electron microscopy of swift heavy ion irradiated ceria.

  7. Ion irradiation-induced structure damage to botanic samples using the ion transmission energy spectrum

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    In order to study the mechanism of irradiation-induced damage ofbotanic samples caused by low energy heavy ions, transmission energy spectrum mea-surement was performed. Kidney bean slice samples 100μm in thickness were irradi-ated by 50 kev N+ ions. The irradiation beam current density was about 30μA/cm2,and the irradiation ion doses were 1×1015, 1×1016, 3×1016 and 1×1017 ions@cm-2,respectively. A target set up that could greatly reduce the incident ion current densitywas designed to achieve the damage-free measurement. The 3.2 MeV H+ transmittedion energy spectrum measurement was carried out before and after the irradiation.From the transmission ion energy spectrum, it was found that the kidney bean sliceitself was structurally inhomogeneous compared with the PET films (C10HsO4). Ourresults indicated that the average mass thickness changed little when the N+ iondose was below 3×1016 ions.cm-2, but changed obviously whcn ion dose was beyond3×1016 ions.cm-2.

  8. Forsterite Amorphisation by Ion Irradiation: Monitoring by Infrared Spectroscopy

    CERN Document Server

    Brucato, J R; Baratta, G; Colangeli, L

    2003-01-01

    We present experimental results on crystal--amorphous transition of forsterite (Mg2SiO4) silicate under ion irradiation. The aim of this work is to study the structural evolution of one of the most abundant crystalline silicates observed in space driven by ion irradiation. To this aim, forsterite films have been sythesised in laboratory and irradiated with low energy (30--60 keV) ion beams. Structural changes during irradiation with H+, He+, C+, and Ar++ have been observed and monitored by infrared spectroscopy. The fraction of crystalline forsterite converted into amorphous is a function of the energy deposited by nuclear collision by ions in the target. Laboratory results indicate that ion irradiation is a mechanism potentially active in space for the amorphisation of silicates. Physical properties obtained in this work can be used to model the evolution of silicate grains during their life cycle from evolved stars, through different interstellar environments and up to be incorporated in Solar System object...

  9. Irradiation of graphene field effect transistors with highly charged ions

    Science.gov (United States)

    Ernst, P.; Kozubek, R.; Madauß, L.; Sonntag, J.; Lorke, A.; Schleberger, M.

    2016-09-01

    In this work, graphene field-effect transistors are used to detect defects due to irradiation with slow, highly charged ions. In order to avoid contamination effects, a dedicated ultra-high vacuum set up has been designed and installed for the in situ cleaning and electrical characterization of graphene field-effect transistors during irradiation. To investigate the electrical and structural modifications of irradiated graphene field-effect transistors, their transfer characteristics as well as the corresponding Raman spectra are analyzed as a function of ion fluence for two different charge states. The irradiation experiments show a decreasing mobility with increasing fluences. The mobility reduction scales with the potential energy of the ions. In comparison to Raman spectroscopy, the transport properties of graphene show an extremely high sensitivity with respect to ion irradiation: a significant drop of the mobility is observed already at fluences below 15 ions/μm2, which is more than one order of magnitude lower than what is required for Raman spectroscopy.

  10. TiO2 films photocatalytic activity improvements by swift heavy ions irradiation

    Science.gov (United States)

    Rafik, Hazem; Mahmoud, Izerrouken; Mohamed, Trari; Abdenacer, Benyagoub

    2014-08-01

    TiO2 thin films synthesized by sol-gel on glass substrates are irradiated by 90 MeV Xe ions at various fluences and room temperature under normal incidence. The structural, electrical, optical and surface topography properties before and after Xe ions irradiation are investigated. X-ray diffraction (XRD) reveals that the crystallinity is gradually destroyed, and the films become amorphous above 5×1012 ions/cm2. The band gap is not affected by Xe ions irradiation as evidenced from the optical measurements. By contrast, the conductivity increases with raising Xe fluence. The energy band diagram established from the electrochemical characterization shows the feasibility of TiO2 films for the photo-electrochemical chromate reduction. Xe ion irradiation results in enhanced photocatalytic activity in aquatic medium, evaluated by the reduction of Cr(VI) into trivalent state. TiO2 films irradiated at 1013 Xe/cm2 exhibit the highest photoactivity; 69% of chromate (10 ppm) is reduced at pH 3 after 4 h of exposure to sunlight (1120 mW cm-2) with a quantum yield of 0.06%.

  11. Optical and dielectric properties of ion beam irradiated Ag/polymethyl methacrylate nanocomposites.

    Science.gov (United States)

    Gavade, Chaitali; Singh, N L; Khanna, P K

    2014-08-01

    Changes in the dielectric, optical, structural and thermal properties of PMMA/silver nanocomposites of different concentrations of silver nanoparticles (5%, 10%, 15%) due to swift heavy ion irradiation were studied by means of impedance gain phase analyzer, UV-visible spectroscopy, X-ray diffraction and differential scanning calorimetry. Samples were irradiated with 120 MeV Si-ions at fluences of 1 x 10(11), 1 x 10(12) ions/cm2. Dependence of dielectric properties on frequency, ion beam fluence and filler concentration was studied. The results revealed the enhancement in dielectric properties after dopping nanoparticles and also upon irradiation. Optical properties like band gap was estimated for pure polymer and nanocomposite films from their optical absorption spectra in the wavelength region 200-800 nm. It was found that the band gap value shifted to lower energy (from 4.58 eV to 3.21 eV) on doping with silver nanoparticles. Differential scanning calorimetry analysis revealed a decrease in the glass transition temperature upon irradiation, which may be attributed to scissioning of polymer chain due to ion beam irradiation which is also confirmed with XRD analysis.

  12. Livestock wastewater treatment by zeolite ion exchange and gamma-ray irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Sang Ryul; Kim, Tak Hyun; Lee, Myun Joo [Radiation Research Center for Industry and Environment, Korea Atomic Energy Research Institute, Jeongeup (Korea, Republic of)

    2008-01-15

    Livestock wastewater containing high concentrations of organic matters and ammonia-nitrogen has been known as one of the recalcitrant wastewater. It is difficult to treat by conventional wastewater treatment techniques. This study was carried out to evaluate the feasibility of zeolite ion exchange and gamma-ray irradiation treatment of livestock wastewater. The removal efficiencies of SCOD{sub Cr} and NH3-N were significantly enhanced by gamma-ray irradiation after zeolite ion exchange as a pre-treatment. However, the effects of zeolite particle size on the SCOD{sub Cr} and NH{sub 3}-N removal efficiencies were insignificant. These results indicate that the combined process of zeolite ion exchange and gamma-ray irradiation has potential for the treatment of livestock wastewater.

  13. Raman measurements in silica glasses irradiated with energetic ions

    Energy Technology Data Exchange (ETDEWEB)

    Saavedra, R., E-mail: rafael.saavedra@ciemat.es; Martin, P.; Vila, R. [Materiales para Fusión, Laboratorio Nacional de Fusión, CIEMAT, Avda. Complutense, 40, 28040 Madrid (Spain); León, M. [Laboratoire Hubert Curien, UMR CNRS 5516, Université Jean Monnet, Bâtiment F 18 Rue du Professeur Benoît Lauras F43000 Saint-Étienne, France and Institut de Chimie Moléculaire et des Matériaux d' Orsay (ICMMO) (France); Jiménez-Rey, D. [Materiales para Fusión, Laboratorio Nacional de Fusión, CIEMAT, Avda. Complutense, 40, 28040 Madrid, Spain and Centro de Micro-Análisis de Materiales (CMAM), Universidad Autónoma de Madrid (UAM), Cantoblanco, 28049 Madrid (Spain); Girard, S.; Boukenter, A.; Ouerdane, Y. [Laboratoire Hubert Curien, UMR CNRS 5516, Université Jean Monnet, Bâtiment F 18 Rue du Professeur Benoît Lauras F43000 Saint-Étienne (France)

    2014-10-21

    Ion irradiation with energetic He{sup +} (2.5 MeV), O{sup 4+} (13.5 MeV), Si{sup 4+} (24.4 MeV) and Cu{sup 7+} (32.6 MeV) species at several fluences (from 5 × 10{sup 12} to 1.65 × 10{sup 15} ion/cm{sup 2}) were performed in three types of SiO{sub 2} glasses with different OH content (KU1, KS-4V and Infrasil 301). After ion implantation the Raman spectra were measured and compared with the spectra of unirradiated samples. Irradiated samples of the three fused silica grades exhibit changes in the broad and asymmetric R-band (ω{sub 1} around 445 cm{sup −1}), in D{sub 1} (490 cm−1) and D{sub 2} (605 cm{sup −1}) bands associated to small-membered rings. The D{sub 2} band shows an increase with increasing fluences for different ions, indicating structural changes. Raman spectra of ion-irradiated samples were compared with the spectra of neutron irradiated samples at fluences 10{sup 17} n/cm{sup 2} and 1018 n/cm{sup 2}. Macroscopic surface cracking was detected, mainly at fluences corresponding to deposited energies between 10{sup 23} eV/cm{sup 3} and 10{sup 24} eV/cm{sup 3} (after ion beam shutdown)

  14. Influence of 12C6+ ion irradiation on mutant avermitilis

    Science.gov (United States)

    Wang, Shu-Yang; Chen, Ji-Hong; Li, Wen-Jian; Liang, Jian-Ping; Bo, Yong-Heng; Ma, Xiao-Qi; Liu, Jing

    2012-11-01

    The effects of 12C+6 ion irradiation on colony morphology and mycelia morphology, as well as on mutation rate have been studied in the B1a high-product strains (ZJAV-Y1-203) mutated by heavy ion irradiation and compared with that in the original strain (ZJAV-A-1). After irradiating the rate of a straw hat colony type having a high ability of producing B1a in ZJAV-Y1-203 strains was higher than that found in ZJAV-A-1 strains. When strains were cultured in a liquid medium for 24 hours, the mycelium becoming thinner could be observed in all of the irradiated ZJAV- Y1-203 groups, but only in the ZJAV-A-1 groups irradiated at the dose of 50 Gy or more. The early growth of mycelium was inhibited in the ZJAV- Y1-203 group irradiated with a high dose. The highest positive mutation rate (23.5%) of ZJAV - Y1 - 203 was reached at the lower dose of 30 Gy while the highest positive mutation rate of 34.2% in ZJAV-A-1 appeared at 50 Gy. These results indicate that the effects of heavy ion irradiation still exist even in the mutated Streptomyces avermitilis, and only the dose is lower and the effects not so strong compared with the one that is first irradiated with optimized heavy ion doses. This is evidence of the one directional mutation being controlled by many more factors in a organism.

  15. Influence of 12C6+ ion irradiation on mutant avermitilis

    Institute of Scientific and Technical Information of China (English)

    WANG Shu-Yang; CHEN Ji-Hong; LI Wen-Jian; LIANG Jian-Ping; BO Yong-Heng; MA Xiao-Qi; LIU Jing

    2012-01-01

    The effects of 12C+6ion irradiation on colony morphology and mycelia morphology,as well as on mutation rate have been studied in the Bla high-product strains (ZJAV-Y1-203) mutated by heavy ion irradiation and compared with that in the original strain (ZJAV-A-1).After irradiating the rate of a straw hat colony type having a high ability of producing B1a in ZJAV-Y1-203 strains was higher than that found in ZJAV-A-1 strains.When strains were cultured in a liquid medium for 24 hours,the mycelium becoming thinner could be observed in all of the irradiated ZJAV-Y1-203 groups,but only in the ZJAV-A-1 groups irradiated at the dose of 50 Gy or more.The early growth of mycelium was inhibited in the ZJAV-Y1-203 group irradiated with a high dose.The highest positive mutation rate (23.5%) of ZJAV-Y1-203 was reached at the lower dose of 30 Gy while the highest positive mutation rate of 34.2% in ZJAV-A-1 appeared at 50 Gy.These results indicate that the effects of heavy ion irradiation still exist even in the mutated Streptomyces avermitilis,and only the dose is lower and the effects not so strong compared with the one that is first irradiated with optimized heavy ion doses.This is evidence of the one directional mutation being controlled by many more factors in a organism.

  16. Propagation of Plasma Generated by Intense Pulsed Ion Beam Irradiation

    Institute of Scientific and Technical Information of China (English)

    WU Di; GONG Ye; LIU Jin-Yuan; WANG Xiao-Gang; LIU Yue; MA Teng-Cai

    2006-01-01

    @@ Taking the calculation results based on the established two-dimensional ablation model of the intense-pulsed-ion-beam (IPIB) irradiation process as initial conditions, we build a two-dimensional hydrodynamic ejection model of plasma produced by an IPIB-irradiated metal titanium target into ambient gas. We obtain the conclusions that shock waves generate when the background pressure is around 133 mTorr and also obtain the plume splitting phenomenon that has been observed in the experiments.

  17. Electron transferring from titanium ion irradiated carbon nanotube arrays into vacuum under low applied fields

    Science.gov (United States)

    Deng, Jian-hua; Ping, Zhao-xia; Zheng, Rui-ting; Cheng, Guo-an

    2011-05-01

    Field emission characteristics of carbon nanotube arrays synthesized by thermal chemical vapor deposition on iron ion pre-bombarded silicon substrate are enhanced by titanium ion irradiation. A pronounced degradation of turn-on electric field of 0.305 V/μm and threshold field, of which the lowest value is only 1.054 V/μm, about 0.482 V/μm at the dose of 5 × 10 16 ions/cm 2 is as an expression of this enhancement. Scanning electron microscopy, Raman spectroscopy, x-ray photoelectron spectroscopy, Photoelectron spectrometer and transmission electron microscopy are measured for comparison before and after the Ti ion irradiation of the carbon nanotube arrays, and the results reveal that the formation of carbon nanorod/nanotube heterostructure during ion irradiation plays a dominative role in the promotion of the field emission properties. However, high-dose irradiating transaction on carbon nanotube arrays will exert repulsive effects on the field emission characteristics for the introduction of severe structural damage. Additionally, the longtime eminent stability behaviors under high applied fields have provided a possibility for the potential application of field emission flat panel display or electron emitters based on carbon nanotube arrays.

  18. Folding two dimensional crystals by swift heavy ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Ochedowski, Oliver; Bukowska, Hanna [Fakultät für Physik and CENIDE, Universität Duisburg-Essen, D-47048 Duisburg (Germany); Freire Soler, Victor M. [Fakultät für Physik and CENIDE, Universität Duisburg-Essen, D-47048 Duisburg (Germany); Departament de Fisica Aplicada i Optica, Universitat de Barcelona, E08028 Barcelona (Spain); Brökers, Lara [Fakultät für Physik and CENIDE, Universität Duisburg-Essen, D-47048 Duisburg (Germany); Ban-d' Etat, Brigitte; Lebius, Henning [CIMAP (CEA-CNRS-ENSICAEN-UCBN), 14070 Caen Cedex 5 (France); Schleberger, Marika, E-mail: marika.schleberger@uni-due.de [Fakultät für Physik and CENIDE, Universität Duisburg-Essen, D-47048 Duisburg (Germany)

    2014-12-01

    Ion irradiation of graphene, the showcase model of two dimensional crystals, has been successfully applied to induce various modifications in the graphene crystal. One of these modifications is the formation of origami like foldings in graphene which are created by swift heavy ion irradiation under glancing incidence angle. These foldings can be applied to locally alter the physical properties of graphene like mechanical strength or chemical reactivity. In this work we show that the formation of foldings in two dimensional crystals is not restricted to graphene but can be applied for other materials like MoS{sub 2} and hexagonal BN as well. Further we show that chemical vapour deposited graphene forms foldings after swift heavy ion irradiation while chemical vapour deposited MoS{sub 2} does not.

  19. Reduction and structural modification of zirconolite on He+ ion irradiation

    Science.gov (United States)

    Gupta, Merry; Kulriya, P. K.; Shukla, Rishabh; Dhaka, R. S.; Kumar, Raj; Ghumman, S. S.

    2016-07-01

    The immobilization of minor actinides and alkaline-earth metal is a major concern in nuclear industry due to their long-term radioactive contribution to the high level waste (HLW). Materials having zirconolite, pyrochlore, and perovskite structure are promising candidates for immobilization of HLW. The zirconolite which exhibits high radiation stability and corrosion resistance behavior is investigated for its radiation stability against alpha particles in the present study. CaZrTi2O7 pellets prepared using solid state reaction techniques, were irradiated with 30 keV He+ ions for the ion fluence varying from 1 × 1017 to 1 × 1021 ions/m2. Scanning electron microscopy (SEM) images of the un-irradiated sample exhibited well separated grains with average size of about 6.8 μm. On the ion irradiation, value of the average grains size was about 7.1 μm, and change in the microstructure was insignificant. The X-ray photoelectron spectroscopy (XPS) studies showed a shift in the core level peak position (of Ca 2p, Ti 2p and Zr 3d) towards lower binding energy with respect to pristine sample as well as loss of oxygen was also observed for sample irradiated with the ion fluence of 1 × 1020 ions/m2. These indicate a decrease in co-ordination number and the ionic character of Msbnd O bond. Moreover, core level XPS signal was not detected for sample irradiated with ion fluence of 1 × 1021 ions/m2, suggesting surface damage of the sample at this ion fluence. However, X-ray diffraction (XRD) studies showed that zirconolite was not amorphized even on irradiation up to a fluence order of 1 × 1021 ion/m2. But, significant decrease in peak intensity due to creation of defects and a marginal positive peak shift due to tensile strain induced by irradiation, were observed. Thus, XRD along with XPS investigation suggests that reduction, decrease in co-ordination number, and increase in covalency are responsible for the radiation damage in zirconolite.

  20. Surface modification of multilayer graphene using Ga ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Quan, E-mail: wangq@mail.ujs.edu.cn [School of Mechanical Engineering, Jiangsu University, Zhenjiang 212013 (China); State Key Laboratory of Transducer Technology, Chinese Academy of Sciences, Shanghai 200050 (China); Shao, Ying; Ge, Daohan; Ren, Naifei [School of Mechanical Engineering, Jiangsu University, Zhenjiang 212013 (China); Yang, Qizhi [School of Mechanical Engineering, Jiangsu University, Zhenjiang 212013 (China); State key laboratory of Robotics, Chinese Academy of Sciences, Shengyang 110000 (China)

    2015-04-28

    The effect of Ga ion irradiation intensity on the surface of multilayer graphene was examined. Using Raman spectroscopy, we determined that the irradiation caused defects in the crystal structure of graphene. The density of defects increased with the increase in dwell times. Furthermore, the strain induced by the irradiation changed the crystallite size and the distance between defects. These defects had the effect of doping the multilayer graphene and increasing its work function. The increase in work function was determined using contact potential difference measurements. The surface morphology of the multilayer graphene changed following irradiation as determined by atomic force microscopy. Additionally, the adhesion between the atomic force microscopy tip and sample increased further indicating that the irradiation had caused surface modification, important for devices that incorporate graphene.

  1. Structural evolution of zirconium carbide under ion irradiation

    Science.gov (United States)

    Gosset, D.; Dollé, M.; Simeone, D.; Baldinozzi, G.; Thomé, L.

    2008-02-01

    Zirconium carbide is one of the candidate materials to be used for some fuel components of the high temperature nuclear reactors planned in the frame of the Gen-IV project. Few data exist regarding its behaviour under irradiation. We have irradiated ZrC samples at room temperature with slow heavy ions (4 MeV Au, fluence from 10 11 to 5 × 10 15 cm -2) in order to simulate neutron irradiations. Grazing incidence X-Ray diffraction (GIXRD) and transmission electron microscopy (TEM) analysis have been performed in order to study the microstructural evolution of the material versus ion fluence. A high sensitivity to oxidation is observed with the formation of zirconia precipitates during the ion irradiations. Three damage stages are observed. At low fluence (high micro-strains appear together with small faulted dislocation loops. At the highest fluence (>10 14 cm -2), the micro-strains saturate and the loops coalesce to form a dense dislocation network. No other structural modification is observed. The material shows a moderate cell parameter increase, corresponding to a 0.6 vol.% swelling, which saturates around 10 14 ions/cm 2, i.e., a few Zr dpa. As a result, in spite of a strong covalent bonding component, ZrC seems to have a behaviour under irradiation close to cubic metals.

  2. Chemical Bonding States of TiC Films before and after Hydrogen Ion Irradiation

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    TiC films deposited by rf magnetron sputtering followed by Ar+ ion bombardment were irradiated with a hydrogen ion beam. X-ray photoelectron spectroscopy (XPS) was used for characterization of the chemical bonding states of C and Ti elements of the TiC films before and after hydrogen ion irradiation, in order to understand the effect of hydrogen ion irradiation on the films and to study the mechanism of hydrogen resistance of TiC films. Conclusions can be drawn that ion bombardment at moderate energy can cause preferential physical sputtering of carbon atoms from the surface of low atomic number (Z) material. This means that ion beam bombardment leads to the formation of a non-stoichiometric composition of TiC on the surface.TiC films prepared by ion beam mixing have the more excellent characteristic of hydrogen resistance. One important cause, in addition to TiC itself, is that there are many vacant sites in TiC created by ion beam mixing.These defects can easily trap hydrogen and effectively enhance the effect of hydrogen resistance.

  3. IR and UV irradiations on ion bombarded polycrystalline silver

    Energy Technology Data Exchange (ETDEWEB)

    Latif, Anwar, E-mail: anwarlatif@uet.edu.p [Department of Physics, University of Engineering and Technology, Lahore 54890 (Pakistan); Khaleeq-ur-Rahman, M.; Bhatti, K.A.; Rafique, M.S.; Rizvi, Z.H. [Department of Physics, University of Engineering and Technology, Lahore 54890 (Pakistan)

    2010-10-15

    Ion bombarded polycrystalline fine polished silver surfaces are exposed to Nd:YAG (1064 nm, 10 mJ, 12 ns) and KrF excimer (248 nm, 57 mJ, 20 ns) lasers to examine structural and morphological changes employing X-ray diffractometry and optical microscopy, respectively. Irradiation causes considerable changes in grain sizes. Hydrodynamic sputtering is found to be dominant in heat affected zones (HAZs). Craters with irregular boundary and non-uniform thermal conduction are resulted on laser ablated surfaces of ion bombarded specimens. No disturbance takes place in the d-spacing of the planes of irradiated samples.

  4. FTIR study of silicon carbide amorphization by heavy ion irradiations

    Science.gov (United States)

    Costantini, Jean-Marc; Miro, Sandrine; Pluchery, Olivier

    2017-03-01

    We have measured at room temperature (RT) the Fourier-transform infra-red (FTIR) absorption spectra of ion-irradiated thin epitaxial films of cubic silicon carbide (3C–SiC) with 1.1 µm thickness on a 500 µm thick (1 0 0) silicon wafer substrate. Irradiations were carried out at RT with 2.3 MeV 28Si+ ions and 3.0 MeV 84Kr+ ions for various fluences in order to induce amorphization of the SiC film. Ion projected ranges were adjusted to be slightly larger than the film thickness so that the whole SiC layers were homogeneously damaged. FTIR spectra of virgin and irradiated samples were recorded for various incidence angles from normal incidence to Brewster’s angle. We show that the amorphization process in ion-irradiated 3C–SiC films can be monitored non-destructively by FTIR absorption spectroscopy without any major interference of the substrate. The compared evolutions of TO and LO peaks upon ion irradiation yield valuable information on the damage process. Complementary test experiments were also performed on virgin silicon nitride (Si3N4) self-standing films for similar conditions. Asymmetrical shapes were found for TO peaks of SiC, whereas Gaussian profiles are found for LO peaks. Skewed Gaussian profiles, with a standard deviation depending on wave number, were used to fit asymmetrical peaks for both materials. A new methodology for following the amorphization process is proposed on the basis of the evolution of fitted IR absorption peak parameters with ion fluence. Results are discussed with respect to Rutherford backscattering spectrometry channeling and Raman spectroscopy analysis.

  5. Cation disordering in magnesium aluminate spinel crystals induced by electron or ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Soeda, Takeshi E-mail: soeda@regroup5.nucl.kyushu-u.ac.jp; Matsumura, Syo; Kinoshita, Chiken; Zaluzec, Nestor J

    2000-12-01

    Structural changes in magnesium aluminate spinel (MgO {center_dot} nAl{sub 2}O{sub 3}) single crystals, which were irradiated with 900 keV electrons or 1 MeV Ne{sup +} ions at 873 K, were examined by electron channeling enhanced X-ray microanalysis. Unirradiated MgO {center_dot} Al{sub 2}O{sub 3} has a tendency to form the normal spinel configuration, where Mg{sup 2+} ions and Al{sup 3+} ions occupy mainly the tetrahedral and the octahedral sites, respectively. Electron irradiation induces simple cation disordering between the tetrahedral sites and the octahedral sites in MgO {center_dot} Al{sub 2}O{sub 3}. In addition to cation disordering, slight evacuation of cations from the tetrahedral sites to the octahedral sites occurs in a peak-damaged area in MgO {center_dot} Al{sub 2}O{sub 3} irradiated with Ne{sup +} ions. In contrast, cation disordering is suppressed in MgO {center_dot} 2.4Al{sub 2}O{sub 3} irradiated with electrons. The structural vacancies, present in the non-stoichiometric compound, appear to be effective in promoting irradiation damage recovery through interstitial-vacancy recombination.

  6. Synergic effects of ion irradiations (La, Ce) and alkaline pretreatment (KOH) on hydriding kinetic property of a Mm–Ni based alloy

    Energy Technology Data Exchange (ETDEWEB)

    Abe, H., E-mail: abe.hiroshi10@jaea.go.jp [Quantum Beam Science Directorate, Japan Atomic Energy Agency, 1233 Watanuki, Takasaki, Gunma 370-1292 (Japan); Aone, S.; Morimoto, R.; Uchida, H. [Course of Applied Science, Graduate School of Engineering, Tokai University, 4-1-1 Kitakaname, Hiratsuka, Kanagawa 259-1292 (Japan)

    2013-12-15

    Highlights: •Ion irradiations by various ions onto a Mm–Ni based hydrogen storage alloy. •The generation of vacancy type defects by ion irradiations in the surface of a Mm–Ni based alloy. •The enhancement of the initial rate by the ion irradiations of the Mm surface. •The enhancement of the initial rate by an alkaline treatment of the Mm surface. -- Abstract: The ion beam irradiation is known to produce a high density of vacancy type defects in the surface region of a metal and found to be an effective method as a surface modification in order to enhance the hydriding rate of a metal. In this study, we examined synergic effects of both surface modifications of ion irradiations and alkaline treatment on the initial hydriding rate of a Mm–Ni based alloy. In this study, the irradiations by lanthanum (La) and cerium (Ce) ions combined with an alkaline KOH pretreatment were found much more effective in the enhancement of the initial hydriding rate compared with irradiations with other ions. This study reports the synergic effects of the surface modifications by the both the surface irradiations with rare earth ions of La and Ce, and an alkaline surface treatment on the hydriding kinetics.

  7. Microstructural stability of a self-ion irradiated lanthana-bearing nanostructured ferritic steel

    Energy Technology Data Exchange (ETDEWEB)

    Pasebani, Somayeh [Univ. of Idaho, Moscow, ID (United States). Dept. of Chemical and Materials Engineering; Center for Advanced Energy Studies, Idaho Falls, ID (United States); Charit, Indrajit [Univ. of Idaho, Moscow, ID (United States). Dept. of Chemical and Materials Engineering; Center for Advanced Energy Studies, Idaho Falls, ID (United States); Burns, Jatuporn [Center for Advanced Energy Studies, Idaho Falls, ID (United States); Boise State Univ., ID (United States). Dept. of Materials Science and Engineering; Alsagabi, Sultan [Univ. of Idaho, Moscow, ID (United States). Dept. of Chemical and Materials Engineering; King Abdulaziz City for Science and Technology, Riyadh (Saudi Arabia). Atomic Energy Research Inst.; Butt, Darryl P. [Center for Advanced Energy Studies, Idaho Falls, ID (United States); Boise State Univ., ID (United States). Dept. of Materials Science and Engineering; Cole, James I. [Center for Advanced Energy Studies, Idaho Falls, ID (United States); Idaho National Lab. (INL), Idaho Falls, ID (United States); Price, Lloyd M. [Texas A & M Univ., College Station, TX (United States). Dept. of Nuclear Engineering; Shao, Lin [Texas A & M Univ., College Station, TX (United States). Dept. of Nuclear Engineering

    2015-07-01

    Thermally stable nanofeatures with high number density are expected to impart excellent high temperature strength and irradiation stability in nanostructured ferritic steels (NFSs) which have potential applications in advanced nuclear reactors. A lanthana-bearing NFS (14LMT) developed via mechanical alloying and spark plasma sintering was used in this study. The sintered samples were irradiated by Fe2+ ions to 10, 50 and 100 dpa at 30 °C and 500 °C. Microstructural and mechanical characteristics of the irradiated samples were studied using different microscopy techniques and nanoindentation, respectively. Overall morphology and number density of the nanofeatures remained unchanged after irradiation. Average radius of nanofeatures in the irradiated sample (100 dpa at 500 °C) was slightly reduced. A notable level of irradiation hardening and enhanced dislocation activity occurred after ion irradiation except at 30 °C and ≥50 dpa. Other microstructural features like grain boundaries and high density of dislocations also provided defect sinks to assist in defect removal.

  8. Evaluation of Ion Irradiation Behavior of ODS Alloys

    Energy Technology Data Exchange (ETDEWEB)

    Jang, Jin Sung; Kim, Min Chul; Hong, Jun Hwa; Han, Chang Hee; Chang, Young Mun; Bae, Chang Soo; Bae, Yoon Young; Chang, Moon Hee

    2006-08-15

    FM steel (Grade 92) and ODS alloy(MA956) specimens were ion irradiated with 122 MeV Ne ions. Irradiation temperatures were about 450 and 550 .deg. C and the peak dose was 1, 5, and 10 dpa. Cross-sectional TEM samples were prepared by the electrolytic Ni-plating after pre-treatment of the irradiated specimens. Irradiation cavities in FM steel and ODS alloy specimens were not much different in size; about 20 nm in diameter in both specimens irradiated at around 450 .deg. C. However, the size distribution of cavities in FM steel specimens was broader than that in ODS alloy specimen, indicating that the cavity growth probably via coalescence). It was noticeable that the location and the preferential growth of the cavities in FM steel specimens: cavities on the PAGB (prior austenite grain boundary) was significantly larger than those within the grains. This could be an important issue for the mechanical properties, especially high temperature creep, fracture toughness, and so on. The dependency of the dose threshold and swelling on the ratio of the inert gas concentration/dpa was analysed for the various irradiation source, including He, Ne, Fe/He, and fast neutron, and the empirical correlation was established.

  9. Evaporation of ion-irradiated disks

    CERN Document Server

    Dullemond, C P

    2005-01-01

    We calculate the evaporation of a cool accretion disk around a black hole due to the ion-bombardment by an ion supported accretion flow (here ISAF, or optically thin ADAF). As first suggested by Spruit & Deufel (2002), this evaporation takes place in two stages: ion bombardment of the cool disk (Shakura-Sunyaev disk: SSD) produces an intermediate-temperature layer on top of the disk (`warm layer') which constitutes an independent accretion flow on both sides of the SSD. As this warm material accretes inward of the inner radius of the SSD, it becomes thermally unstable by lack of cooling of photons, and evaporates into the ISAF, thereby feeding the latter. Angular momentum conservation forces a certain fraction of the ISAF material to move outward, where it can bombard the SSD with its hot ions. The flow geometry is derived by computing stationary solutions of the continuity- and angular momentum equations for the three components (ISAF, warm flow and SSD). The overall radiative output is dominated by hard...

  10. Nitrogen ion irradiation of Au(110) : formation of gold nitride

    NARCIS (Netherlands)

    Šiller, L.; Hunt, M.R.C.; Brown, J.W.; Coquel, J-M.; Rudolf, P.

    2002-01-01

    Often metal nitrides posses unique properties for applications, such as great hardness, high melting points, chemical stability, novel electrical and magnetic properties. One route to the formation of metal nitride films is through ion irradiation of metal surfaces. In this report, the results of ir

  11. Enhancement of Irradiation Capability of the Experimental Fast Reactor Joyo

    Science.gov (United States)

    Maeda, Shigetaka; Serine, Takashi; Aoyama, Takafumi; Suzuki, Soju

    2009-08-01

    The experimental fast reactor Joyo is the first sodium-cooled fast reactor in Japan. One of its primary missions is to perform irradiation tests of fuel and structural materials to support the development of fast reactors. The MK-III high performance core upgrade to enhance the irradiation testing capabilities was completed in 2003. In order to expand Joyo's capabilities for innovative irradiation testing applications, neutron spectrum tailoring, lower irradiation temperature, movable sample devices and fast neutron beam holes are being considered. This program responds to existing irradiation needs and aims to further expand capabilities for a variety of irradiation tests.

  12. Modifying the morphology and magnetic properties of magnetite nanoparticles using swift heavy ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Gokhale, Shubha, E-mail: sgokhale@ignou.ac.in [School of Sciences, Indira Gandhi National Open University, New Delhi 110068 (India); Lamba, Subhalakshmi; Kumari, Neha; Singh, Bhupendra [School of Sciences, Indira Gandhi National Open University, New Delhi 110068 (India); Avasthi, D.K. [Inter University Accelerator Centre, P.O. Box 10502, New Delhi 110067 (India); Kulkarni, S.K. [Indian Institute of Science Education Research, Dr. Homi Bhabha Road, Pune 411008 (India)

    2014-08-15

    Magnetite (Fe{sub 3}O{sub 4}) nanospheres of ∼8–11 nm diameter synthesized using a chemical co-precipitation method were deposited as thin films on different substrates using spin coating. The thin films were irradiated with Ag ions at 100 MeV energy. Comparison of unirradiated, as synthesized Fe{sub 3}O{sub 4} nanoparticulate thin film and ion irradiated film shows that irradiation causes dramatic changes in the morphology, structure and magnetic properties. Monte Carlo simulations carried out on this system indicate that the origin of the changes in the magnetic properties lies in the enhanced magnetic anisotropy energy density and reorientation of magnetic easy axis.

  13. LET effects of high energy ion beam irradiation on polysilanes

    Energy Technology Data Exchange (ETDEWEB)

    Seki, Shu; Kanzaki, Kenichi; Tagawa, Seiichi; Yoshida, Yoichi [Osaka Univ., Ibaraki (Japan). Inst. of Scientific and Industrial Research; Kudoh, Hisaaki; Sugimoto, Masaki; Sasuga, Tsuneo; Seguchi, Tadao; Shibata, Hiromi

    1997-03-01

    Thin films of poly(di-n-hexylsilane) were irradiated with 2-20 MeV H{sup +} and He{sup +} ion beams. The beams caused heterogeneous reactions of crosslinking and main chain scission in the films. The relative efficiency of the crosslinking was drastically changed in comparison with that of main chain scission. The anomalous change in the molecular weight distribution was analyzed with increasing irradiation fluence, and the ion beam induced reaction radius; track radius was determined for the radiation sources by the function of molecular weight dispersion. Obtained values were 59{+-}15 A and 14{+-}6 A for 2 MeV He{sup +} and 20 MeV H{sup +} ion beams respectively. (author)

  14. Dose Response of Alanine Detectors Irradiated with Carbon Ion Beams

    DEFF Research Database (Denmark)

    Herrmann, Rochus; Jäkel, Oliver; Palmans, Hugo

    2011-01-01

    Purpose: The dose response of the alanine detector shows a dependence on particle energy and type, when irradiated with ion beams. The purpose of this study is to investigate the response behaviour of the alanine detector in clinical carbon ion beams and compare the results with model predictions....... Methods: Alanine detectors have been irradiated with carbon ions with an energy range of 89-400 MeV/u. The relative effectiveness of alanine has been measured in this regime. Pristine and spread out Bragg peak depth-dose curves have been measured with alanine dosimeters. The track-structure based alanine......-dose curves deviate from predictions in the peak region, most pronounced at the distal edge of the peak. Conclusions: The used model and its implementation show a good overall agreement for quasi mono energetic measurements. Deviations in depth-dose measurements are mainly attributed to uncertainties...

  15. Deuterium ion irradiation induced blister formation and destruction

    Energy Technology Data Exchange (ETDEWEB)

    Song, Jaemin; Kim, Nam-Kyun; Kim, Hyun-Su; Jin, Younggil; Roh, Ki-Baek; Kim, Gon-Ho, E-mail: ghkim@snu.ac.kr

    2016-11-01

    Highlights: • The areal number density of blisters on the grain with (1 1 1) plane orientation increased with increasing ion fluence. • No more blisters were created above the temperature about 900 K due to high thermal mobility of ions and inactivity of traps. • The destruction of blister at the boundary induced by sputtering is proposed. • The blisters were destructed at the position about the boundary by high sputtering yield of oblique incident ions and thin thickness due to plastic deformation at the boundary. - Abstract: The blisters formation and destruction induced by the deuterium ions on a polycrystalline tungsten were investigated with varying irradiation deuterium ion fluence from 3.04 × 10{sup 23} to 1.84 × 10{sup 25} D m{sup −2} s{sup −1} and an fixed irradiated ion energy of 100 eV in an electron cyclotron resonance plasma source, which was similar to the far-scrape off layer region in the nuclear fusion reactors. Target temperature was monitored during the irradiation. Most of blisters formed easily on the grain with (1 1 1) plane orientation which had about 250 nm in diameter. In addition, the areal number density of blisters increased with increasing the ion fluence under the surface temperature reaching to about 900 K. When the fluence exceeded 4.6 × 10{sup 24} D m{sup −2}, the areal number density of the blister decreased. It could be explained that the destruction of the blister was initiated by erosion at the boundary region where the thickness of blister lid was thin and the sputtering yield was high by oblique incident ions, resulting in remaining the lid open, e.g., un-eroded center dome. It is possible to work as a tungsten dust formation from the plasma facing divertor material at far-SOL region of fusion reactor.

  16. Microstructure evolution of metallic nanocrystalline thin-films under ion-beam irradiation

    Science.gov (United States)

    Kaoumi, Djamel

    -growth rate was found to depend on material and on irradiation conditions. In particular, neither grain-growth nor precipitation occurred under 1 MeV electron irradiation. Combined with rate-theory calculations, this shows that long range diffusion does not play a role in the process. A model of grain-growth under ion irradiation in the temperature-independent regime was developed, based on direct impact of irradiation-induced thermal spikes on grain-boundaries. Grain-boundary migration occurs by atomic jumps within the thermal spike biased by the grain-boundary curvature driving force. The model incorporates cascade structure features such as subcascade formation, and the probability of subcascades occurring at grain-boundaries. This results in a power law expression relating the average grain-size with the ion dose, where the exponent is 3 in agreement with the experimental data. In the thermally assisted regime, the increased grain-growth is explained within the framework of the same model, by the increased thermal spike size with higher substrate temperature. At the highest temperatures, other effects such as subcascade overlap and point defect migration to sinks may also enhance the process.

  17. Quantitative Single-Ion Irradiation by ASIPP Microbeam

    Institute of Scientific and Technical Information of China (English)

    WANG Xu-Fei; WU Yu; XU Ming-Liang; WU Li-Jun; WANG Shao-Hu; YU Zeng-Liang; CHEN Lian-Yun; HU Zhi-Wen; WANG Xiao-Hua; ZHANG Jun; LI Jun; CHEN Bin; HU Su-Hua; SHI Zhong-Tao

    2004-01-01

    @@ A single-ion microbeam facility has been constructed by the microbeam research group in ASIPP (Institute of Plasma Physics, Chinese Academy of Science). The system was designed to deliver defined numbers of hydrogen ions produced by a van de Graaff accelerator, covering an energy range from 200keV to 3 MeV, into living cells(5 μm-20 μm diameter) growing in culture on thin plastic films. The beam is collimated by a 1- μm inner diameter HPLC (high performance liquid chromatography) capillary, which forms the micron-dimensional beam-line exit.A microbeam collimator, a scintillation ion counting system and a fast beam shutter, which constitute a precise dosage measuring and controlling system, jointly perform quantitative single-ion irradiation. With this facility,we can presently acquire ion-hitting efficiency close to 95%.

  18. Modification of magnetic anisotropy induced by swift heavy ion irradiation in cobalt ferrite thin films

    Energy Technology Data Exchange (ETDEWEB)

    Nongjai, Razia [Department of Applied Physics, Zakir Hussain College of Engineering & Technology, A.M.U., Aligarh 202002 (India); Khan, Shakeel, E-mail: skhanapad@gmail.com [Department of Applied Physics, Zakir Hussain College of Engineering & Technology, A.M.U., Aligarh 202002 (India); Ahmed, Hilal; Khan, Imran [Department of Applied Physics, Zakir Hussain College of Engineering & Technology, A.M.U., Aligarh 202002 (India); Annapoorni, S. [Department of Physics and Astrophysics, University of Delhi, Delhi 110007 (India); Gautam, Sanjeev [Advanced Analysis Center, Korea Institute of Science and Technology (KIST), Seoul 136-791 (Korea, Republic of); Lin, Hong-Ji; Chang, Fan-Hsiu [National Synchrotron Radiation Research Center (NSRRC), Hsinchu 30076, Taiwan (China); Hwa Chae, Keun [Advanced Analysis Center, Korea Institute of Science and Technology (KIST), Seoul 136-791 (Korea, Republic of); Asokan, K. [Material Science Division, Inter University Accelerator Centre, Aruna Asaf Ali Marg, New Delhi 110067 (India)

    2015-11-15

    The present study demonstrates the modification of magnetic anisotropy in cobalt ferrite (CoFe{sub 2}O{sub 4}) thin films induced by swift heavy ion irradiations of 200 MeV Ag-ion beams. The study reveals that both magnetizations and coercive field are sensitive to Ag-ions irradiation and to the fluences. The magnetic anisotropy enhanced at low fluence of Ag-ions due to domain wall pinning at defect sites created by ion bombardment and at high fluence, this magnetic anisotropy ceases and changes to isotropic behavior which is explained based on the significant structural and morphological changes. An X-ray absorption and x-ray magnetic circular dichroism studies confirms the inverse spinel structure of these compounds. - Highlights: • CoFe{sub 2}O{sub 4} thin films have been deposited on Silicon substrate by pulsed laser deposition technique. • Swift heavy ion irradiation of thin films at three different fluences. • Studied the structural and magnetic properties of the samples. • XRD and Raman studies indicate strain in the films. • Observed perpendicular magnetic anisotropy.

  19. Damage studies on tungsten due to helium ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Dutta, N.J.; Buzarbaruah, N.; Mohanty, S.R., E-mail: smrutirm@yahoo.com

    2014-09-15

    Highlights: • Used plasma focus helium ion source to study radiation induced damage on tungsten. • Surface analyses confirm formation of micro-crack, bubbles, blisters, pinholes, etc. • XRD patterns confirm development of compressive stress due to thermal load. • Reduction in hardness value is observed in the case of exposed sample. - Abstract: Energetic and high fluence helium ions emitted in a plasma focus device have been used successfully to study the radiation induced damage on tungsten. The reference and irradiated samples were characterized by optical microscopy, field emission scanning electron microscopy, X-ray diffraction and by hardness testers. The micrographs of the irradiated samples at lower magnification show uniform mesh of cracks of micrometer width. However at higher magnification, various types of crystalline defects such as voids, pinholes, bubbles, blisters and microcracks are distinctly noticed. The prominent peaks in X-ray diffraction spectrum of irradiated samples are seen shifted toward higher Bragg angles, thus indicating accumulation of compressive stress due to the heat load delivered by helium ions. A marginal reduction in hardness of the irradiated sample is also noticed.

  20. Nanostructure evolution in ODS steels under ion irradiation

    Directory of Open Access Journals (Sweden)

    S. Rogozhkin

    2016-12-01

    In this work, we carried out atom probe tomography (APT and transmission electron microscopy (TEM studies of three different ODS steels produced by mechanical alloying: ODS Eurofer, 13.5Cr ODS and 13.5Cr-0.3Ti ODS. These materials were investigated after irradiation with Fe (5.6MeV or Ti (4.8MeV ions up to 1015ion/cm2 and part of them up to 3×1015ion/cm2. In all cases, areas for TEM investigation were cut at a depth of ∼ 1.3µm from the irradiated surface corresponding to the peak of the radiation damage dose. It was shown that after irradiation at RT and at 300°С the number density of oxide particles in all the samples grew up. Meanwhile, the fraction of small particles in the size distribution has increased. APT revealed an essential increase in nanoclusters number and a change of their chemical composition at the same depth. The nanostructure was the most stable in 13.5Cr-0.3Ti ODS irradiated at 300°С: the increase of the fraction of small oxides was minimal and no change of nanocluster chemical composition was detected.

  1. Ion-irradiation induced chemical ordering of FePt and FePtAu nanoparticles

    Science.gov (United States)

    Seetala, Naidu V.; Harrell, J. W.; Lawson, Jeremy; Nikles, David E.; Williams, John R.; Isaacs-Smith, Tamara

    2005-12-01

    We have studied the effect of ion-beam irradiation on reducing the ordering temperature of FePt and FePtAu nanoparticles. FePt and FePt(Au14%) 4 nm particles dispersed on a Si-substrate were irradiated by 300 keV Al-ions with a dose of 1 × 1016 ions/cm2 at 43 °C using a water-cooled flange in order to minimize the vacancy migration and voids formation within the collision cascades. Partial chemical ordering has been observed in as-irradiated particles with coercivity of 60-130 Oe. Post-irradiation annealing at 220 °C enhanced chemical ordering in FePt nanoparticles with coercivity of 3500 Oe, magnetic anisotropy of 1.5 × 107 erg/cc, and thermal stability factor of 130. A much higher 375 °C post-irradiation annealing was required in FePtAu, presumably because Au atoms were trapped at Fe/Pt lattice sites at lower temperatures. As the annealing temperature increased, anomalous features in the magnetization reversal curves were observed that disappeared at higher annealing temperatures.

  2. Ion-irradiation induced chemical ordering of FePt and FePtAu nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Seetala, Naidu V. [Department of Physics, Grambling State University, RWE Jones Drive, Carver Hall 81, Grambling, LA 71245 (United States)]. E-mail: naidusv@gram.edu; Harrell, J.W. [MINT Center, University of Alabama, Tuscaloosa, AL 35487 (United States); Lawson, Jeremy [MINT Center, University of Alabama, Tuscaloosa, AL 35487 (United States); Nikles, David E. [MINT Center, University of Alabama, Tuscaloosa, AL 35487 (United States); Williams, John R. [Department of Physics, Auburn University, Auburn, AL 36849 (United States); Isaacs-Smith, Tamara [Department of Physics, Auburn University, Auburn, AL 36849 (United States)

    2005-12-15

    We have studied the effect of ion-beam irradiation on reducing the ordering temperature of FePt and FePtAu nanoparticles. FePt and FePt(Au14%) 4 nm particles dispersed on a Si-substrate were irradiated by 300 keV Al-ions with a dose of 1 x 10{sup 16} ions/cm{sup 2} at 43 {sup o}C using a water-cooled flange in order to minimize the vacancy migration and voids formation within the collision cascades. Partial chemical ordering has been observed in as-irradiated particles with coercivity of 60-130 Oe. Post-irradiation annealing at 220 {sup o}C enhanced chemical ordering in FePt nanoparticles with coercivity of 3500 Oe, magnetic anisotropy of 1.5 x 10{sup 7} erg/cc, and thermal stability factor of 130. A much higher 375 {sup o}C post-irradiation annealing was required in FePtAu, presumably because Au atoms were trapped at Fe/Pt lattice sites at lower temperatures. As the annealing temperature increased, anomalous features in the magnetization reversal curves were observed that disappeared at higher annealing temperatures.

  3. The effect of carbon impurities on molybdenum surface morphology evolution under high-flux low-energy helium ion irradiation

    Science.gov (United States)

    Tripathi, J. K.; Novakowski, T. J.; Gonderman, S.; Bharadwaj, N.; Hassanein, A.

    2016-09-01

    We report on the role of carbon (C) impurities, in molybdenum (Mo) fuzz evolutions on Mo surface during 100 eV He+ ion irradiations. In this study we considered 0.01, 0.05, and 0.5% C+ ion impurities in He+ ion irradiations. For introducing such tiny C+ ion impurities, gas mixtures of He and CH4 have been chosen in following ratios; 99.95: 0.05, 99.75: 0.25, and 97.5: 2.5. Apart from these three cases, two additional cases, 100% He+ ion (for Mo fuzz growth due to only He+ ions) and 100% H+ ion (for confirming the significance of tiny 0.04-2.0% H+ ions in terms of Mo fuzz evolutions on Mo surface, if any), have also been considered. Ion energy (100 eV), ion fluence (2.6 × 1024 ions m-2), and target temperature (923 K) were kept constant for each experiment and their selections were based on our previous studies [1,2]. Our study shows homogeneously populated and highly dense Mo fuzz evolutions on entire Mo surface for 100% He+ ion irradiation case. Enhancement of C+ ion impurities in He+ ions causes a sequential reduction in Mo fuzz evolutions, leading to almost complete prevention of Mo fuzz evolutions for 0.5% C+ ion impurity concentrations. Additionally, no fuzz formation for 100% H+ ion irradiation at all, were seen (apart from some tiny nano-structuring, in very limited regions). This indicates that there is no significant role of H+ ions in Mo fuzz evolutions (at least for such tiny amount, 0.04-2.0% H+ ions). The study is significant to understand the behavior of potential high-Z plasma facing components (PFCs), in the, presence of tiny amount of C impurities, for nuclear fusion relevant applications.

  4. Titanium Carbide and Silicon Carbide Thermal Conductivity under Heavy Ions Irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Cabrero, J.; Weisbecker, P.; Pailler, R. [LCTS, F-33600 Pessac (France); Cabrero, J.; Audubert, F. [CEA Cadarache, DEN 13108 Saint Paul Iez Durance (France); Kusiak, A. [TREFLE, Esplanade des Arts et Metiers 33405 Talence Cedex (France)

    2010-07-01

    SiC(f)/SiC ceramic matrix composites (CMC) are considered as structural materials in next generation fission nuclear reactors. However, thermal conductivity of SiC is reduced on the one hand at the highest temperatures, but also under irradiation. Titanium carbide, because of its peculiar thermal properties is an attractive material to be used as a matrix in a CMC to enhance the thermal conductivity of CMC under irradiation and at high temperature. In this study, we performed irradiation experiments on TiC, TiC{sub x}SiC{sub 1-x} and SiC samples, with heavy ions at room temperature (74 MeV Kr, fluence from 10{sup 13} to 10{sup 15} ions/cm{sup 2}). This energy results in an irradiated layer of about 7 {mu}m for TiC. Thermal conductivity of the irradiated layer is measured using IR radiometry as a function of fluence and composition. The structural evolution of the irradiated samples was investigated by Raman micro spectroscopy and transmission electron microscopy. (authors)

  5. Kr ion irradiation study of the depleted-uranium alloys

    Science.gov (United States)

    Gan, J.; Keiser, D. D.; Miller, B. D.; Kirk, M. A.; Rest, J.; Allen, T. R.; Wachs, D. M.

    2010-12-01

    Fuel development for the reduced enrichment research and test reactor (RERTR) program is tasked with the development of new low enrichment uranium nuclear fuels that can be employed to replace existing high enrichment uranium fuels currently used in some research reactors throughout the world. For dispersion type fuels, radiation stability of the fuel-cladding interaction product has a strong impact on fuel performance. Three depleted-uranium alloys are cast for the radiation stability studies of the fuel-cladding interaction product using Kr ion irradiation to investigate radiation damage from fission products. SEM analysis indicates the presence of the phases of interest: U(Al, Si) 3, (U, Mo)(Al, Si) 3, UMo 2Al 20, U 6Mo 4Al 43 and UAl 4. Irradiations of TEM disc samples were conducted with 500 keV Kr ions at 200 °C to ion doses up to 2.5 × 10 19 ions/m 2 (˜10 dpa) with an Kr ion flux of 10 16 ions/m 2/s (˜4.0 × 10 -3 dpa/s). Microstructural evolution of the phases relevant to fuel-cladding interaction products was investigated using transmission electron microscopy.

  6. Characterization of swift heavy ion irradiation damage in ceria

    Energy Technology Data Exchange (ETDEWEB)

    Yablinsky, Clarissa A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Devanathan, Ram [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Pakarinen, Janne [Inst. for Nuclear Research Center (SCK-CEN), Mol, (Belgium); Gan, Jian [Idaho National Lab. (INL), Idaho Falls, ID (United States); Severin, Daniel [GSI-Darmstadt (Germany); Trautmann, Christina [GSI-Darmstadt (Germany); Allen, Todd R. [Univ. of Wisconsin, Madison, WI (United States). Energy Physics Dept.

    2015-03-04

    Swift heavy ion induced radiation damage is investigated for ceria (CeO2), which serves as a UO2 fuel surrogate. Microstructural changes resulting from an irradiation with 940 MeV gold ions of 42 keV/nm electronic energy loss are investigated by means of electron microscopy accompanied by electron energy loss spectroscopy showing that there exists a small density reduction in the ion track core. While chemical changes in the ion track are not precluded, evidence of them was not observed. Classical molecular dynamics simulations of thermal spikes in CeO2 with an energy deposition of 12 and 36 keV/nm show damage consisting of isolated point defects at 12 keV/nm, and defect clusters at 36 keV/nm, with no amorphization at either energy. Inferences are drawn from modeling about density changes in the ion track and the formation of interstitial loops that shed light on features observed by electron microscopy of swift heavy ion irradiated ceria.

  7. Late degeneration in rabbit tissues after irradiation by heavy ions

    Science.gov (United States)

    Lett, J. T.; Cox, A. B.; Keng, P. C.; Lee, A. C.; Su, C. M.; Bergtold, D. S.

    1980-01-01

    Results are presented for investigations of the late effects of heavy-ion irradiation on rabbit tissues which were undertaken to assess the hazards associated with the long-term exposure of humans to heavy ions in space during such activities as the construction of solar power stations or voyages to Mars. White rabbits approximately six weeks old were exposed to various doses of collimated beams of 400-MeV/n Ne ions, 570 MeV/n Ar ions and Co-60 gamma rays directed through both eyes, and the responses of the various tissues (hair follicles, skin, cornea, lens, retina, Harderian glands, bone and forebrain) were examined. Proliferating tissues are found to exhibit high damage levels in the early and late periods following irradiation, while terminally differentiating tissues repond to radiation most intensely in the late period, years after irradiation, with no intermediate recovery. The results obtained from rabbits are used to predict the occurrence of late tissue degeneration in the central nervous system, terminally differentiating systems and stem cells of humans one or more decades following exposure to radiation levels anticipated during long-duration space flights. The studies also indicate that tissues may be prematurely aged in the sense that tissue life spans may be shortened without the development of malignancies.

  8. Elastic wave from fast heavy ion irradiation on solids

    Science.gov (United States)

    Kambara, T.; Kageyama, K.; Kanai, Y.; Kojima, T. M.; Nanai, Y.; Yoneda, A.; Yamazaki, Y.

    2002-06-01

    To study the time-dependent mechanical effects of fast heavy ion irradiations, we have irradiated various solids by a short-bunch beam of 95 MeV/u Ar ions and observed elastic waves generated in the bulk. The irradiated targets were square-shaped plates of poly-crystals of metals (Al and Cu), invar alloy, ceramic (Al 2O 3), fused silica (SiO 2) and single crystals of KC1 and LiF with a thickness of 10 mm. The beam was incident perpendicular to the surface and all ions were stopped in the target. Two piezo-electric ultrasonic sensors were attached to the surface of the target and detected the elastic waves. The elastic waveforms as well as the time structure and intensity of the beam bunch were recorded for each shot of a beam bunch. The sensor placed opposite to the beam spot recorded a clear waveform of the longitudinal wave across the material, except for the invar and fused silica targets. From its propagation time along with the sound velocity and the thickness of the target, the depth of the wave source was estimated. The result was compared with ion ranges calculated for these materials by TRIM code.

  9. Late degeneration in rabbit tissues after irradiation by heavy ions

    Science.gov (United States)

    Lett, J. T.; Cox, A. B.; Keng, P. C.; Lee, A. C.; Su, C. M.; Bergtold, D. S.

    1980-01-01

    Results are presented for investigations of the late effects of heavy-ion irradiation on rabbit tissues which were undertaken to assess the hazards associated with the long-term exposure of humans to heavy ions in space during such activities as the construction of solar power stations or voyages to Mars. White rabbits approximately six weeks old were exposed to various doses of collimated beams of 400-MeV/n Ne ions, 570 MeV/n Ar ions and Co-60 gamma rays directed through both eyes, and the responses of the various tissues (hair follicles, skin, cornea, lens, retina, Harderian glands, bone and forebrain) were examined. Proliferating tissues are found to exhibit high damage levels in the early and late periods following irradiation, while terminally differentiating tissues repond to radiation most intensely in the late period, years after irradiation, with no intermediate recovery. The results obtained from rabbits are used to predict the occurrence of late tissue degeneration in the central nervous system, terminally differentiating systems and stem cells of humans one or more decades following exposure to radiation levels anticipated during long-duration space flights. The studies also indicate that tissues may be prematurely aged in the sense that tissue life spans may be shortened without the development of malignancies.

  10. In-situ Study of Nanostructure and Electrical Resistance of Nanocluster Films Irradiated with Ion Beams

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Weilin; Sundararajan, Jennifer A.; Varga, Tamas; Bowden, Mark E.; Qiang, You; McCloy, John S.; Henager, Charles H.; Montgomery, Robert O.

    2014-08-11

    An in-situ study is reported on the structural evolution in nanocluster films under He+ ion irradiation using an advanced helium ion microscope. The films consist of loosely interconnected nanoclusters of magnetite or iron-magnetite (Fe-Fe3O4) core-shells. The nanostructure is observed to undergo dramatic changes under ion-beam irradiation, featuring grain growth, phase transition, particle aggregation, and formation of nanowire-like network and nano-pores. Studies based on ion irradiation, thermal annealing and election irradiation have indicated that the major structural evolution is activated by elastic nuclear collisions, while both electronic and thermal processes can play a significant role once the evolution starts. The electrical resistance of the Fe-Fe3O4 films measured in situ exhibits a super-exponential decay with dose. The behavior suggests that the nanocluster films possess an intrinsic merit for development of an advanced online monitor for neutron radiation with both high detection sensitivity and long-term applicability, which can enhance safety measures in many nuclear operations.

  11. Structural and electrical properties of swift heavy ion beam irradiated Fe/Si interface

    Indian Academy of Sciences (India)

    Chhagan Lal; R K Jain; I P Jain

    2007-04-01

    The present work deals with the mixing of iron and silicon by swift heavy ions in high-energy range. The thin film was deposited on a -Si (111) substrate at 10-6 torr and at room temperature. Irradiations were undertaken at room temperature using 120 MeV Au+9 ions at the Fe/Si interface to investigate ion beam mixing at various doses: 5 × 1012 and 5 × 1013 ions/cm2. Formation of different phases of iron silicide has been investigated by X-ray diffraction (XRD) technique, which shows enhancement of intermixing and silicide formation as a result of irradiation. – measurements for both pristine and irradiated samples have been carried out at room temperature, series resistance and barrier heights for both as deposited and irradiated samples were extracted. The barrier height was found to vary from 0.73–0.54 eV. The series resistance varied from 102.04–38.61 k.

  12. Amorphization and reduction of thermal conductivity in porous silicon by irradiation with swift heavy ions

    Energy Technology Data Exchange (ETDEWEB)

    Newby, Pascal J. [Institut des Nanotechnologies de Lyon, Universite de Lyon, INL-UMR5270, CNRS, INSA de Lyon, Villeurbanne 69621 (France); Institut Interdisciplinaire d' Innovation Technologique (3IT), Universite de Sherbrooke, CNRS UMI-LN2, Sherbrooke, Quebec J1K0A5 (Canada); Canut, Bruno; Bluet, Jean-Marie; Lysenko, Vladimir [Institut des Nanotechnologies de Lyon, Universite de Lyon, INL-UMR5270, CNRS, INSA de Lyon, Villeurbanne 69621 (France); Gomes, Severine [Centre de Thermique de Lyon, Universite de Lyon, CETHIL-UMR5008, CNRS, INSA de Lyon, Villeurbanne 69621 (France); Isaiev, Mykola; Burbelo, Roman [Faculty of Physics, Taras Shevchenko National University of Kyiv, 64/13, Volodymyrs' ka St., Kyiv 01601 (Ukraine); Termentzidis, Konstantinos [Laboratoire LEMTA, Universite de Lorraine-CNRS UMR 7563, 54506 Vandoeuvre-les-Nancy cedex (France); Chantrenne, Patrice [Universite de Lyon, INSA de Lyon, MATEIS-UMR CNRS 5510, Villeurbanne 69621 (France); Frechette, Luc G. [Institut Interdisciplinaire d' Innovation Technologique (3IT), Universite de Sherbrooke, CNRS UMI-LN2, Sherbrooke, Quebec J1K0A5 (Canada)

    2013-07-07

    In this article, we demonstrate that the thermal conductivity of nanostructured porous silicon is reduced by amorphization and also that this amorphous phase in porous silicon can be created by swift (high-energy) heavy ion irradiation. Porous silicon samples with 41%-75% porosity are irradiated with 110 MeV uranium ions at six different fluences. Structural characterisation by micro-Raman spectroscopy and SEM imaging show that swift heavy ion irradiation causes the creation of an amorphous phase in porous Si but without suppressing its porous structure. We demonstrate that the amorphization of porous silicon is caused by electronic-regime interactions, which is the first time such an effect is obtained in crystalline silicon with single-ion species. Furthermore, the impact on the thermal conductivity of porous silicon is studied by micro-Raman spectroscopy and scanning thermal microscopy. The creation of an amorphous phase in porous silicon leads to a reduction of its thermal conductivity, up to a factor of 3 compared to the non-irradiated sample. Therefore, this technique could be used to enhance the thermal insulation properties of porous Si. Finally, we show that this treatment can be combined with pre-oxidation at 300 Degree-Sign C, which is known to lower the thermal conductivity of porous Si, in order to obtain an even greater reduction.

  13. [Grain boundary and interface kinetics during ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Atwater, H.A.

    1991-12-31

    Proposed here is renewed support of a research program focused on interface motion and phase transformation during ion irradiation, with emphasis on elemental semiconductors. Broadly speaking, the aims of this program are to explore defect kinetics in amorphous and crystalline semiconductors, and to relate defect dynamics to interface motion and phase transformations. Over the last three years, we initiated a program under DOE support to explore crystallization and amorphization of elemental semiconductors under irradiation. This research has enabled new insights about the nature of defects in amorphous semiconductors and about microstructural evolution in the early stages of crystallization. In addition, we have demonstrated almost arbitrary control over the relative rates of crystal nucleation and crystal growth in silicon. As a result, the impinged grain microstructure of thin (100 nm) polycrystalline films crystallized under irradiation can be controlled with grain sizes ranging from a few nanometers to several micrometers, which may have interesting technological implications.

  14. Etch rate modeling for ion-irradiated nitrocellulose

    Energy Technology Data Exchange (ETDEWEB)

    Merhari, L.; Belorgeot, C.; Moliton, J.P. (Laboratoire d' electronique des Polymeres sous Faisceaux Ioniques, 123, Avenue Albert Thomas, 87060 Limoges Cedex (France))

    1990-12-24

    The self-developing mechanism of nitrocellulose when used as an ion beam resist is described by a model predicting the evolution of the etch rate versus irradiation time. Fundamentals of the model based on ion energy deposition dependent ablative development along with related mathematical derivations are given and briefly discussed. Comparison between theoretical results and experimental data available for protons at 20 keV and Ne{sup +}, Ar{sup +}, Kr{sup +} ions at 150 keV is made and shows a good agreement. This result clearly does not conflict with our assumption that the nitrocellulose etch rate is dependent on the total ion deposited energy no matter how the energy is deposited.

  15. Collisional activation of ions by off-resonance irradiation in ion cyclotron resonance spectrometry

    Science.gov (United States)

    Shin, Seung Koo; Han, Seung-Jin; Seo, Jongcheol

    2009-06-01

    Collisional activation of ions in the ion cyclotron resonance (ICR) cell by short off-resonance burst irradiation (ORBI) was studied by time-resolved photodissociation of the meta-bromotoluene radical cation. Off-resonance chirp or single-frequency burst was applied for 2 ms to the probe ion in the presence of Ar buffer gas. The amount of internal energy imparted to the probe ion by collision under ORBI was precisely determined by time-resolved photodissociation spectroscopy. The rate of unimolecular dissociation of the probe ion following the photolysis at 532 nm was measured by monitoring the real-time appearance of the C7H7+ product ion. The internal energy of the probe ion was extracted from the known rate-energy curve. To help understand the collisional activation of an ion under ORBI, we simulated the radial trajectory of the ion using Green's method. The calculated radial kinetic energy was converted to the collision energy in the center-of-mass frame, and the collision frequency was estimated by using a reactive hard-sphere collision model with an ion-induced dipole potential. Both experiments and trajectory simulations suggest that chirp irradiation leads to less collisional activation of ions than other waveforms.

  16. Precipitation behavior of AlxCoCrFeNi high entropy alloys under ion irradiation

    Science.gov (United States)

    Yang, Tengfei; Xia, Songqin; Liu, Shi; Wang, Chenxu; Liu, Shaoshuai; Fang, Yuan; Zhang, Yong; Xue, Jianming; Yan, Sha; Wang, Yugang

    2016-08-01

    Materials performance is central to the satisfactory operation of current and future nuclear energy systems due to the severe irradiation environment in reactors. Searching for structural materials with excellent irradiation tolerance is crucial for developing the next generation nuclear reactors. Here, we report the irradiation responses of a novel multi-component alloy system, high entropy alloy (HEA) AlxCoCrFeNi (x = 0.1, 0.75 and 1.5), focusing on their precipitation behavior. It is found that the single phase system, Al0.1CoCrFeNi, exhibits a great phase stability against ion irradiation. No precipitate is observed even at the highest fluence. In contrast, numerous coherent precipitates are present in both multi-phase HEAs. Based on the irradiation-induced/enhanced precipitation theory, the excellent structural stability against precipitation of Al0.1CoCrFeNi is attributed to the high configurational entropy and low atomic diffusion, which reduces the thermodynamic driving force and kinetically restrains the formation of precipitate, respectively. For the multiphase HEAs, the phase separations and formation of ordered phases reduce the system configurational entropy, resulting in the similar precipitation behavior with corresponding binary or ternary conventional alloys. This study demonstrates the structural stability of single-phase HEAs under irradiation and provides important implications for searching for HEAs with higher irradiation tolerance.

  17. Precipitation behavior of AlxCoCrFeNi high entropy alloys under ion irradiation

    Science.gov (United States)

    Yang, Tengfei; Xia, Songqin; Liu, Shi; Wang, Chenxu; Liu, Shaoshuai; Fang, Yuan; Zhang, Yong; Xue, Jianming; Yan, Sha; Wang, Yugang

    2016-01-01

    Materials performance is central to the satisfactory operation of current and future nuclear energy systems due to the severe irradiation environment in reactors. Searching for structural materials with excellent irradiation tolerance is crucial for developing the next generation nuclear reactors. Here, we report the irradiation responses of a novel multi-component alloy system, high entropy alloy (HEA) AlxCoCrFeNi (x = 0.1, 0.75 and 1.5), focusing on their precipitation behavior. It is found that the single phase system, Al0.1CoCrFeNi, exhibits a great phase stability against ion irradiation. No precipitate is observed even at the highest fluence. In contrast, numerous coherent precipitates are present in both multi-phase HEAs. Based on the irradiation-induced/enhanced precipitation theory, the excellent structural stability against precipitation of Al0.1CoCrFeNi is attributed to the high configurational entropy and low atomic diffusion, which reduces the thermodynamic driving force and kinetically restrains the formation of precipitate, respectively. For the multiphase HEAs, the phase separations and formation of ordered phases reduce the system configurational entropy, resulting in the similar precipitation behavior with corresponding binary or ternary conventional alloys. This study demonstrates the structural stability of single-phase HEAs under irradiation and provides important implications for searching for HEAs with higher irradiation tolerance. PMID:27562023

  18. UV Irradiance Enhancements by Scattering of Solar Radiation from Clouds

    Directory of Open Access Journals (Sweden)

    Uwe Feister

    2015-08-01

    Full Text Available Scattering of solar radiation by clouds can reduce or enhance solar global irradiance compared to cloudless-sky irradiance at the Earth’s surface. Cloud effects to global irradiance can be described by Cloud Modification Factors (CMF. Depending on strength and duration, irradiance enhancements affect the energy balance of the surface and gain of solar power for electric energy generation. In the ultraviolet region, they increase the risk for damage to living organisms. Wavelength-dependent CMFs have been shown to reach 1.5 even in the UV-B region at low altitudes. Ground-based solar radiation measurements in the high Andes region at altitudes up to 5917 m a.s.l showed cloud-induced irradiance enhancements. While UV-A enhancements were explained by cloud scattering, both radiation scattering from clouds and Negative Ozone Anomalies (NOA have been discussed to have caused short-time enhancement of UV-B irradiance. Based on scenarios using published CMF and additional spectroradiometric measurements at a low-altitude site, the contribution of cloud scattering to the UV-B irradiance enhancement in the Andes region has been estimated. The range of UV index estimates converted from measured UV-B and UV-A irradiance and modeled cloudless-sky ratios UV-B/erythemal UV is compatible with an earlier estimate of an extreme UV index value of 43 derived for the high Andes.

  19. An IR study of pure and ion irradiated frozen formamide

    CERN Document Server

    Brucato, J R; Strazzulla, G; Baratta, Giuseppa A.; Brucato, John R.; Strazzulla, Giovanni

    2006-01-01

    Context. The chemical evolution of formamide (HCONH2), a molecule of astrobiological interest that has been tentatively identified in interstellar ices and in cometary coma, has been studied in laboratory under simulated astrophysical conditions such as ion irradiation at low temperature. Aims. To evaluate the abundances of formamide observed in space or in laboratory, the integrated absorbances for all the principal IR features of frozen amorphous pure formamide deposited at 20 K were measured. Further evidence that energetic processing of ices occurring in space is extremely relevant both to astrochemistry and to astrobiology has been found, showing that new molecular species are synthesized by ion irradiation at a low temperature. Methods. Pure formamide were deposited at 20 K and IR transmission spectra measured for different ice thicknesses. The ice thickness was derived by looking at the interference pattern (intensity versus time) of a He-Ne laser beam reflected at an angle of 45 deg by the vacuum-film...

  20. Mutagenic effects of heavy ion irradiation on rice seeds

    Energy Technology Data Exchange (ETDEWEB)

    Xu Xue [School of Agronomy, Anhui Agricultural University, 130 Changjiang West Road, Hefei 230036 (China); Key Laboratory of Ion Beam Bio-Engineering, Institute of Technical Biology and Agriculture Engineering, 350 Shushanhu Road, Hefei 230031 (China); Liu Binmei; Zhang Lili [Key Laboratory of Ion Beam Bio-Engineering, Institute of Technical Biology and Agriculture Engineering, 350 Shushanhu Road, Hefei 230031 (China); Wu Yuejin, E-mail: yjwu@ipp.ac.cn [Key Laboratory of Ion Beam Bio-Engineering, Institute of Technical Biology and Agriculture Engineering, 350 Shushanhu Road, Hefei 230031 (China)

    2012-11-01

    Three varieties of rice seeds were subjected to irradiation using low-energy and medium-energy ions. The damage and mutations induced by the ions were examined. In addition, genetic analysis and gene mapping of spotted leaf (spl) mutants were performed. Low-energy ions had no significant influence on germination, survival or seedling height, except for the survival of Nipponbare. Medium-energy ions had a significant influence on germination and survival but had no significant effect on seedling height. In the low-energy group, among 60,000 M{sub 2} plants, 2823 putative morphological mutants were found, and the mutation frequency was approximately 4.71%. In the medium-energy group, 3132 putative morphological mutants were found, and the mutation frequency was approximately 5.22%. Five spl mutants (spl29-spl33) were obtained by ion irradiation, and the heredity of the spl mutants was stable. The characteristics of the spl mutants were found, by genetic analysis and preliminary mapping, to be controlled by a single recessive gene, and spl30 and spl33 were found to be new lesion-mimic mutants.

  1. Variation in the electrical properties of ion beam irradiated cadmium selenate nanowires

    Science.gov (United States)

    Chauhan, R. P.; Narula, Chetna; Panchal, Suresh

    2016-05-01

    The key feature of nanowires consists in the pronounced change in properties induced by the low dimensionality and high surface to volume ratio. The study of electrical transport properties of nanowires is important for electronic device applications. Energetic ions create changes, which may be structural or chemical, in a material along their track and these changes might alter the material's properties. The demand of the modern technology is to understand the effect of radiation on the different properties of the material for its further applications. The present study is on the high-energy Nickel ion beam (160 MeV Ni+12) induced modifications in the electrical and structural properties of the cadmium selenate nanowires. An enhancement in the electrical conductivity of irradiated wires was observed as the ion fluence was increased especially in the forward I-V characteristics. The creation of defects by ion irradiation and the synergy of the ions during their passage in the sample with the intrinsic charge carriers may be responsible for the variation in the transport properties of the irradiated nanowires.

  2. Amorphization and recrystallization of single-crystalline hydrogen titanate nanowires by N{sup +} ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Behera, Akshaya K.; Bandyopadyay, Malay K.; Chatterjee, Shyamal, E-mail: shyamal@iitbbs.ac.in [School of Basic Sciences, Indian Institute of Technology Bhubaneswar, Bhubaneswar 751007 (India); Facsko, Stefan [Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden-Rossendorf, 01328 Dresden (Germany); Das, Siddhartha [Department of Metallurgical and Materials Engineering, Indian Institute of Technology Kharagpur, Kharagpur 721302 (India)

    2014-06-21

    We report on the phase transformation of hydrogen titanate (H{sub 2}Ti{sub 3}O{sub 7}) nanowires induced by 50 keV N{sup +} ion irradiation at room temperature with fluences of 1 × 10{sup 15} ions/cm{sup 2} and 1 × 10{sup 16} ions/cm{sup 2}, respectively. Using transmission electron microscopy, the internal structure of the ion irradiated nanowires is analyzed. At low fluence, a transformation from crystalline H{sub 2}Ti{sub 3}O{sub 7} to amorphous TiO{sub 2} is observed. However, at higher fluence, a remarkable crystalline-amorphous TiO{sub 2} core-shell structure is formed. At this higher fluence, the recrystallization occurs in the core of the nanowire and the outer layer remains amorphous. The phase transformation and formation of core-shell structure are explained using the thermal spike model, radiation enhanced diffusion, and classical theory of nucleation and growth under non-equilibrium thermodynamics. X-ray photoelectron spectroscopy and Raman scattering reveal further insight into the structure of the nanowires before and after ion irradiation.

  3. Metastable hydronium ions in UV-irradiated ice

    Energy Technology Data Exchange (ETDEWEB)

    Moon, Eui-Seong; Kang, Heon [Department of Chemistry, Seoul National University, 1 Gwanak-ro, Seoul 151-747 (Korea, Republic of)

    2012-11-28

    We show that the irradiation of UV light (10-11 eV) onto an ice film produces metastable hydronium (H{sub 3}O{sup +}) ions in the ice at low temperatures (53-140 K). Evidence of the presence of metastable hydronium ions was obtained by experiments involving adsorption of methylamine onto UV-irradiated ice films and hydrogen-deuterium (H/D) isotopic exchange reaction. The methylamine adsorption experiments showed that photogenerated H{sub 3}O{sup +} species transferred a proton to the methylamine arriving at the ice surface, thus producing the methyl ammonium ion, which was detected by low energy sputtering method. The H{sub 3}O{sup +} species induced the H/D exchange of water, which was monitored through the detection of water isotopomers on the surface by using the Cs{sup +} reactive ion scattering method. Thermal and temporal stabilities of H{sub 3}O{sup +} and its proton migration activity were examined. The lifetime of the hydronium ions in the amorphized ice was greater than 1 h at {approx}53 K and decreased to {approx}5 min at 140 K. Interestingly, a small portion of hydronium ions survived for an extraordinarily long time in the ice, even at 140 K. The average migration distance of protons released from H{sub 3}O{sup +} in the ice was estimated to be about two water molecules at {approx}54 K and about six molecules at 100 K. These results indicate that UV-generated hydronium ions can be efficiently stabilized in low-temperature ice. Such metastable hydronium ions may play a significant role in the acid-base chemistry of ice particles in interstellar clouds.

  4. Molecular Ultrasound Imaging of Early Vascular Response in Prostate Tumors Irradiated with Carbon Ions

    Directory of Open Access Journals (Sweden)

    Moritz Palmowski

    2009-09-01

    Full Text Available Individualized treatments with combination of radiotherapy and targeted drugs require knowledge about the behavior of molecular targets after irradiation. Angiogenic marker expression has been studied after conventional radiotherapy, but little is known about marker response to charged particles. For the very first time, we used molecular ultrasound imaging to intraindividually track changes in angiogenic marker expression after carbon ion irradiation in experimental tumors. Expression of intercellular adhesion molecule-1 (ICAM-1 and of αvβ3-integrin in subcutaneous AT-1 prostate cancers in rats treated with carbon ions (16 Gy was studied using molecular ultrasound and immunohistochemistry. For this purpose, cyanoacrylate microbubbles were synthesized and linked to specific ligands. The accumulation of targeted microbubbles in tumors was quantified before and 36 hours after irradiation. In addition, tumor vascularization was analyzed using volumetric Doppler ultrasound. In tumors, the accumulation of targeted microbubbles was significantly higher than in nonspecific ones and could be inhibited competitively. Before irradiation, no difference in binding of αvβ3-integrin-specific or ICAM-1-specific microbubbles was observed in treated and untreated animals. After irradiation, however, treated animals showed a significantly higher binding of αvβ3-integrin-specific microbubbles and an enhanced binding of ICAM-1-specific microbubbles than untreated controls. In both groups, a decrease in vascularization occurred during tumor growth, but no significant difference was observed between irradiated and nonirradiated tumors. In conclusion, carbon ion irradiation upregulates ICAM-1 and αvβ3-integrin expression in tumor neovasculature. Molecular ultrasound can indicate the regulation of these markers and thus may help to identify the optimal drugs and time points in individualized therapy regimens.

  5. Iron ion irradiation increases promotes adhesion of monocytic cells to arterial vascular endothelium

    Science.gov (United States)

    Kucik, Dennis; Khaled, Saman; Gupta, Kiran; Wu, Xing; Yu, Tao; Chang, Polly; Kabarowski, Janusz

    Radiation causes inflammation, and chronic, low-level vascular inflammation is a risk factor for atherosclerosis. Consistent with this, exposure to radiation from a variety of sources is associated with increased risk of heart disease and stroke. Part of the inflammatory response to radiation is a change in the adhesiveness of the endothelial cells that line the blood vessels, triggering inappropriate accumulation of leukocytes, leading to later, damaging effects of inflammation. Although some studies have been done on the effects of gamma irradiation on vascular endothelium, the response of endothelium to heavy ion radiation likely to be encountered in prolonged space flight has not been determined. We investigated how irradiation of aortic endothelial cells with iron ions affects adhesiveness of cultured aortic endothelial cells for monocytic cells and the consequences of this for development of atherosclerosis. Aortic endothelial cells were irradiated with 600 MeV iron ions at Brookhaven National Laboratory and adhesion-related changes were measured. Cells remained viable for at least 72 hours, and were even able to repair acute damage to cell junctions. We found that iron ion irradiation altered expression levels of specific endothelial cell adhesion molecules. Further, these changes had functional consequences. Using a flow chamber adhesion assay to measure adhesion of monocytic cells to endothelial cells under physiological shear stress, we found that adhesivity of vascular endothelium was enhanced in as little as 24 hours after irradiation. Further, the radiation dose dependence was not monotonic, suggesting that it was not simply the result of endothelial cell damage. We also irradiated aortic arches and carotid arteries of Apolipoprotein-E-deficient mice. Histologic analysis of these mice will be conducted to determine whether effects of radiation on endothelial adhesiveness result in consequences for development of atherosclerosis. (Supported by NSBRI

  6. Protective coatings preventing hydrogen desorption from titanium during ion irradiation

    Science.gov (United States)

    Evsin, A. E.; Begrambekov, L. B.; Dovganyuk, S. S.; Kaplevsky, A. S.; Shutikova, M. I.

    2017-05-01

    Effect of yttria and titanium nitride coatings on features of deuterium desorption from titanium layer is investigated. It is shown that both coatings significantly raise the temperature of maximum of deuterium thermal desorption from titanium under linear heating and prevent desorption under prolonged keeping at the operating temperature of a neutron tube target. However, under irradiation with ions of H2 + O2 plasma the barrier properties of titanium nitride appear to degrade.

  7. Elastic wave from fast heavy ion irradiation on solids

    CERN Document Server

    Kambara, T; Kanai, Y; Kojima, T M; Nanai, Y; Yoneda, A; Yamazaki, Y

    2002-01-01

    To study the time-dependent mechanical effects of fast heavy ion irradiations, we have irradiated various solids by a short-bunch beam of 95 MeV/u Ar ions and observed elastic waves generated in the bulk. The irradiated targets were square-shaped plates of poly-crystals of metals (Al and Cu), invar alloy, ceramic (Al sub 2 O sub 3), fused silica (SiO sub 2) and single crystals of KC1 and LiF with a thickness of 10 mm. The beam was incident perpendicular to the surface and all ions were stopped in the target. Two piezo-electric ultrasonic sensors were attached to the surface of the target and detected the elastic waves. The elastic waveforms as well as the time structure and intensity of the beam bunch were recorded for each shot of a beam bunch. The sensor placed opposite to the beam spot recorded a clear waveform of the longitudinal wave across the material, except for the invar and fused silica targets. From its propagation time along with the sound velocity and the thickness of the target, the depth of the...

  8. Ion irradiation of AZO thin films for flexible electronics

    Science.gov (United States)

    Boscarino, Stefano; Torrisi, Giacomo; Crupi, Isodiana; Alberti, Alessandra; Mirabella, Salvatore; Ruffino, Francesco; Terrasi, Antonio

    2017-02-01

    Aluminum doped Zinc oxide (AZO) is a promising transparent conductor for solar cells, displays and touch-screen technologies. The resistivity of AZO is typically improved by thermal annealing at temperatures not suitable for plastic substrates. Here we present a non-thermal route to improve the electrical and structural properties of AZO by irradiating the TCO films with O+ or Ar+ ion beams (30-350 keV, 3 × 1015-3 × 1016 ions/cm2) after the deposition on glass and flexible polyethylene naphthalate (PEN). X-ray diffraction, optical absorption, electrical measurements, Rutherford Backscattering Spectrometry and Atomic Force Microscopy evidenced an increase of the crystalline grain size and a complete relief of the lattice strain upon ion beam irradiation. Indeed, the resistivity of thin AZO films irradiated at room temperature decreased of two orders of magnitude, similarly to a thermal annealing at 400 °C. We also show that the improvement of the electrical properties does not simply depend on the strain or polycrystalline domain size, as often stated in the literature.

  9. Light ion irradiation for unfavorable soft tissue sarcoma

    Energy Technology Data Exchange (ETDEWEB)

    Linstadt, D.; Castro, J.R.; Phillips, T.L.; Petti, P.L.; Collier, J.M.; Daftari, I.; Schoethaler, R.; Rayner, A.

    1990-09-01

    Between 1978 and 1989, 32 patients with unfavorable soft tissue sarcoma underwent light ion (helium, neon) irradiation with curative intent at Lawrence Berkeley Laboratory. The tumors were located in the trunk in 22 patients and head and neck in 10. Macroscopic tumor was present in 22 at the time of irradiation. Two patients had tumors apparently induced by previous therapeutic irradiation. Follow-up times for surviving patients ranged from 4 to 121 months (median 27 months). The overall 3-year actuarial local control rate was 62%; the corresponding survival rate was 50%. The 3-year actuarial control rate for patients irradiated with macroscopic tumors was 48%, while none of the patients with microscopic disease developed local recurrence (100%). The corresponding 3-year actuarial survival rates were 40% (macroscopic) and 78% (microscopic). Patients with retroperitoneal sarcoma did notably well; the local control rate and survival rate were 64% and 62%, respectively. Complications were acceptable; there were no radiation related deaths, while two patients (6%) required operations to correct significant radiation-related injuries. These results appear promising compared to those achieved by low -LET irradiation, and suggest that this technique merits further investigation.

  10. Ion exchange in KTiOPO4 crystals irradiated by copper and hydrogen ions.

    Science.gov (United States)

    Zhang, Ruifeng; Lu, Fei; Lian, Jie; Liu, Hanping; Liu, Xiangzhi; Lu, Qingming; Ma, Hongji

    2008-05-12

    Cs(+)-K+ ion exchanges were produced on KTiOPO4 crystals which is prior irradiated by Cu+ can H+ ions. The energy and dose of implanted Cu+ ions are 1.5 MeV and 0.5 x 10(14) ions/cm2, and that of H+ are 300 keV and 1 x 10(16) ions/cm2, respectively. The temperature of ions exchange is 430 degrees C, and the time range from 15 minutes to 30 minutes. The prism coupling method is used to measure the dark mode spectra of the samples. Compared with results of ion exchange on the sample without irradiations, both the number of guided mode and its corresponding effective refractive index are decreased. The experimental results indicate that the ion exchange rate closely related with the lattice damage and the damage layers formed in the depth of maximum nuclear energy deposition act as a barrier to block the ions diffuse into the sample and the concentration of defects can modify the speed of ion exchange..

  11. Heavy ion tracks in polycarbonate. Comparison with a heavy ion irradiated model compound (diphenyl carbonate)

    Science.gov (United States)

    Ferain, E.; Legras, R.

    1993-09-01

    The chemical modifications induced by energetic heavy ion irradiation of polycarbonate (PC) film are determined by GPC, HPLC, ESR, TGA, IR and UV spectrophotometry. The main results of the irradiation are creation of radicals, chain scission, cross-linking and appearance of new chemical groups in the main polymer chain. As far as the creation of new groups is concerned, they are determined by means of a model compound of PC: the diphenyl carbonate (DPC). The following compounds are identified after energetic heavy ion irradiation of DPC: salicylic acid, phenol, 4,4'-biphenol, 2,4'-biphenol, 2,2'-biphenol, 4-phenoxyphenol, 2-phenoxyphenol, phenyl ether, phenyl benzoate, phenyl salicylate, 2-phenylphenol and 2-phenoxyphenyl benzoate. A similarity between the heavy ion irradiation and a heat treatment has also been established with DPC. On the basis of these results, we try to give an explanation of the preferential attack along the tracks of the irradiated film. Also, an explanation of the well-known beneficial effect of an UV exposition of the irradiated film on the selectivity of this preferential chemical attack is suggested.

  12. Enhancement of uranium-accumulating ability of microorganisms by irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Sakaguchi, Takashi; Nakajima, Akira; Tsuruta, Takehiko [Miyazaki Medical Coll., Kiyotake (Japan)

    1998-01-01

    Some microorganisms having excellent ability to accumulate uranium were isolated, from soil and water systems in and around the Ningyo-toge Station of Power Reactor and Nuclear Fuel Development Corporation. The enhancement of uranium-accumulating ability of microorganisms by electron-beam irradiation was examined, and the ability of JW-046 was increased 3-5% by the irradiation. The irradiation affect the growth of some of microorganisms tested. (author)

  13. Semiconducting Properties of Swift Au Ion-Irradiated ZnO Thin Films at Room Temperature

    Science.gov (United States)

    Kwon, Sera; Park, Hyun-Woo; Chung, Kwun-Bum

    2017-02-01

    The semiconducting properties of Au ion-irradiated ZnO thin films were investigated as a function of ion irradiation dose at room temperature. The Au ion irradiation was conducted with acceleration energy of 130 MeV in the ion dose range from 1 × 1011 to 5 × 1012 ions/cm2. The physical properties showed no change regardless of the Au ion irradiation dose; however, the electrical properties of Au ion-irradiated ZnO thin films changed, depending on the Au ion irradiation dose. The electronic structure drastically changed with the evolution of hybridized molecular orbital structure for the conduction band and band edge states below the conduction band. These remarkable changes in electronic structure correlate with changes in electrical properties, such as carrier concentration and mobility.

  14. Characterization of polymeric films subjected to lithium ion beam irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Gary S. Groenewold; W. Roger Cannon; Paul A. Lessing; Recep Avci; Muhammedin Deliorman; Mark Wolfenden; Doug W. Akers; J. Keith Jewell

    2013-02-01

    Two different polymeric materials that are candidate materials for use as binders for mixed uranium–plutonium oxide nuclear fuel pellets were subjected to Li ion beam irradiation, in order to simulate intense alpha irradiation. The materials (a polyethylene glycol 8000 and a microcrystalline wax) were then analyzed using a combination of mass spectrometry (MS) approaches and X-ray photoelectron spectroscopy (XPS). Samples of the irradiated PEG materials were dissolved in H2O and then analyzed using electrospray ionization-MS, which showed the formation of a series of small oligomers in addition to intact large PEG oligomers. The small oligomers were likely formed by radiation-induced homolytic scissions of the C–O and C–C bonds, which furnish radical intermediates that react by radical recombination with Hradical dot and OHradical dot. Surface analysis using SIMS revealed a heterogeneous surface that contained not only PEG-derived polymers, but also hydrocarbon-based entities that are likely surface contaminants. XPS of the irradiated PEG samples indicated the emergence of different carbon species, with peak shifts suggesting the presence of sp2 carbon atoms. Analysis of the paraffinic film using XPS showed the emergence of oxygen on the surface of the sample, and also a broadening and shifting of the C1s peak, demonstrating a change in the chemistry on the surface. The paraffinic film did not dissolve in either H2O or a H2O–methanol solution, and hence the bulk of the material could not be analyzed using electrospray. However a series of oligomers was leached from the bulk material that produced ion series in the ESI-MS analyses that were identified octylphenyl ethoxylate oligomers. Upon Li ion bombardment, these shifted to a lower average molecular weight, but more importantly showed the emergence of three new ion series that are being formed as a result of radiation damage. Surface analysis of the paraffinic polymers using SIMS produced spectra that were

  15. Characterization of polymeric films subjected to lithium ion beam irradiation

    Science.gov (United States)

    Groenewold, Gary S.; Cannon, W. Roger; Lessing, Paul A.; Avci, Recep; Deliorman, Muhammedin; Wolfenden, Mark; Akers, Doug W.; Jewell, J. Keith; Zuck, Larry D.

    2013-02-01

    Two different polymeric materials that are candidate materials for use as binders for mixed uranium-plutonium oxide nuclear fuel pellets were subjected to Li ion beam irradiation, in order to simulate intense alpha irradiation. The materials (a polyethylene glycol 8000 and a microcrystalline wax) were then analyzed using a combination of mass spectrometry (MS) approaches and X-ray photoelectron spectroscopy (XPS). Samples of the irradiated PEG materials were dissolved in H2O and then analyzed using electrospray ionization-MS, which showed the formation of a series of small oligomers in addition to intact large PEG oligomers. The small oligomers were likely formed by radiation-induced homolytic scissions of the C-O and C-C bonds, which furnish radical intermediates that react by radical recombination with Hrad and OHrad . Surface analysis using SIMS revealed a heterogeneous surface that contained not only PEG-derived polymers, but also hydrocarbon-based entities that are likely surface contaminants. XPS of the irradiated PEG samples indicated the emergence of different carbon species, with peak shifts suggesting the presence of sp2 carbon atoms. Analysis of the paraffinic film using XPS showed the emergence of oxygen on the surface of the sample, and also a broadening and shifting of the C1s peak, demonstrating a change in the chemistry on the surface. The paraffinic film did not dissolve in either H2O or a H2O-methanol solution, and hence the bulk of the material could not be analyzed using electrospray. However a series of oligomers was leached from the bulk material that produced ion series in the ESI-MS analyses that were identified octylphenyl ethoxylate oligomers. Upon Li ion bombardment, these shifted to a lower average molecular weight, but more importantly showed the emergence of three new ion series that are being formed as a result of radiation damage. Surface analysis of the paraffinic polymers using SIMS produced spectra that were wholly dominated by

  16. Evaluation of cell behavior on modified polypropylene with swift heavy ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Arbeitman, Claudia R., E-mail: arbeitman@tandar.cnea.gov.ar [Gerencia de Investigacion y Aplicaciones, TANDAR-CNEA, Av. Gral. Paz 1499, 1650 San Martin, Bs. As. (Argentina); CONICET, Av. Rivadavia 1917, C1033AAJ, CABA (Argentina); Ibanez, Irene L. [CONICET, Av. Rivadavia 1917, C1033AAJ, CABA (Argentina); Garcia Bermudez, Gerardo [Gerencia de Investigacion y Aplicaciones, TANDAR-CNEA, Av. Gral. Paz 1499, 1650 San Martin, Bs. As. (Argentina); CONICET, Av. Rivadavia 1917, C1033AAJ, CABA (Argentina); Duran, Hebe [CONICET, Av. Rivadavia 1917, C1033AAJ, CABA (Argentina); Gerencia de Desarrollo Tecnologico y Proyectos Especiales, TANDAR-CNEA (Argentina); Grosso, Mariela F. del [Gerencia de Investigacion y Aplicaciones, TANDAR-CNEA, Av. Gral. Paz 1499, 1650 San Martin, Bs. As. (Argentina); CONICET, Av. Rivadavia 1917, C1033AAJ, CABA (Argentina); Salguero, Noelia [Gerencia de Investigacion y Aplicaciones, TANDAR-CNEA, Av. Gral. Paz 1499, 1650 San Martin, Bs. As. (Argentina); Mazzei, Ruben [U.A. Tecnologicas y Agropecuarias, CNEA (Argentina)

    2012-02-15

    Ion beam irradiation is a well known means to change the physico-chemical properties of polymers, and induced bio and citocompatibility in controlled conditions and in selected areas of surface. However, the enhancement of cell adhesion on a modified substrate does not mean that the surface is adequate for functional cells. The purpose of the present work is to study proliferation, changes in cytoskeleton and cell morphology on substrates as a function of irradiation parameters. We irradiated polypropylene with sulfur (S) ion-beam at energies of 110 MeV with fluences between 1 Multiplication-Sign 10{sup 6} and 2 Multiplication-Sign 10{sup 10} ions cm{sup -2}. NIH 3T3 cells were cultured on each sample. Cell morphology was observed using phase contrast microscopy and cytoskeleton proteins with fluorescence microscopy. The analysis show different cellular responses as a functions of irradiation parameter, strongly suggests that different underlying substratum can result in distinct types of cytoskeleton reorganization.

  17. Physical Investigation of Au8+ Ions Irradiated CdSe/FTO Thin Films

    Directory of Open Access Journals (Sweden)

    Yuvraj G. Gudage

    2010-06-01

    Full Text Available Thin films of cadmium selenide (CdSe have been electrodeposited on Fluorine doped tin oxide (FTO coated glass substrate in an electrolyte containing Cd(CH3COO2.2H2O and SeO2 at pH 2.7 and temperature 300 K. The as-deposited films were irradiated using Au8+ ions with energy of 100 MeV at fluencies of 1 x 1011 and 1 x 1012 ions/cm2 using tandem pelletron accelerator. The irradiation-induced modifications in CdSe thin films were studied using structural, optical and electrical X-ray diffraction (XRD, scanning electron microscopy (SEM, optical band gap, and I-V characteristics. XRD analysis revealed that the as-deposited films were polycrystalline in nature with cubic phase. After irradiating the films with Au8+ ions metastable cubic phase transformed into stable polycrystalline hexagonal phase. An enhancement in grain size, decrease in band gap energy and decrease in resistivity of the film after irradiation was seen from SEM micrographs, optical analysis, and I-V characteristics, respectively.

  18. Thermal property tuning in aligned carbon nanotube films and random entangled carbon nanotube films by ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Jing [Department of Materials Science and Engineering, Texas A& M University, College Station, Texas 77843 (United States); Chen, Di; Wang, Xuemei [Department of Nuclear Engineering, Texas A& M University, College Station, Texas 77843 (United States); Bykova, Julia S.; Zakhidov, Anvar A. [The Alan G. MacDiarmid NanoTech Institute, University of Texas at Dallas, Richardson, Texas 75080 (United States); Shao, Lin, E-mail: lshao@tamu.edu [Department of Materials Science and Engineering, Texas A& M University, College Station, Texas 77843 (United States); Department of Nuclear Engineering, Texas A& M University, College Station, Texas 77843 (United States)

    2015-10-12

    Ion irradiation effects on thermal property changes are compared between aligned carbon nanotube (A-CNT) films and randomly entangled carbon nanotube (R-CNT) films. After H, C, and Fe ion irradiation, a focusing ion beam with sub-mm diameter is used as a heating source, and an infrared signal is recorded to extract thermal conductivity. Ion irradiation decreases thermal conductivity of A-CNT films, but increases that of R-CNT films. We explain the opposite trends by the fact that neighboring CNT bundles are loosely bonded in A-CNT films, which makes it difficult to create inter-tube linkage/bonding upon ion irradiation. In a comparison, in R-CNT films, which have dense tube networking, carbon displacements are easily trapped between touching tubes and act as inter-tube linkage to promote off-axial phonon transport. The enhancement overcomes the phonon transport loss due to phonon-defect scattering along the axial direction. A model is established to explain the dependence of thermal conductivity changes on ion irradiation parameters including ion species, energies, and current.

  19. Ion irradiation damage in ilmenite under cryogenic conditions

    Energy Technology Data Exchange (ETDEWEB)

    Mitchell, J.N.; Yu, N.; Devanathan, R.; Sickafus, K.E.; Nastasi, M.A. [Los Alamos National Lab., NM (United States). Materials Science and Technology Div.; Nord, G.L. Jr. [Geological Survey, Reston, VA (United States)

    1996-11-01

    A natural single crystal of ilmenite was irradiated at 100 K with 200 keV Ar{sup 2+}. Rutherford backscattering spectroscopy and ion channeling with 2 MeV He{sup +} ions were used to monitor damage accumulation in the surface region of the implanted crystal. At an irradiation fluence of 1 {times} 10{sup 15} Ar{sup 2+} cm{sup {minus}2}, considerable near-surface He{sup +} ion dechanneling was observed, to the extent that ion yield from a portion of the aligned crystal spectrum reached the yield level of a random spectrum. This observation suggests that the near-surface region of the crystal was amorphized by the implantation. Cross-sectional transmission electron microscopy and electron diffraction on this sample confirmed the presence of a 150 mm thick amorphous layer. These results are compared to similar investigations on geikielite (MgTiO{sub 3}) and spinel (MgAl{sub 2}O{sub 4}) to explore factors that may influence radiation damage response in oxides.

  20. Ion irradiation damage in ilmenite at 100 K

    Energy Technology Data Exchange (ETDEWEB)

    Mitchell, J.N.; Yu, N.; Devanathan, R.; Sickafus, K.E.; Nastasi, M.A. [Los Alamos National Lab., NM (United States). Materials Science and Technology Div.; Nord, G.L. Jr. [Geological Survey, Reston, VA (United States)

    1997-10-01

    A natural single crystal of ilmenite (FeTiO{sub 3}) was irradiated at 100 K with 200 keV Ar{sup 2+}. Rutherford backscattering spectroscopy and ion channeling with MeV He{sup +} ions were used to monitor damage accumulation in the surface region of the implanted crystal. At an irradiation fluence of 1 {times} 10{sup 15} Ar{sup 2+} cm{sup {minus}2}, considerable near-surface He{sup +} ion dechanneling was observed, to the extent that ion yield from a portion of the aligned crystal spectrum reached the yield level of a random spectrum. This observation suggests that the near-surface region of the crystal was amorphized by the implantation. Cross-sectional transmission electron microscopy and electron diffraction on this sample confirmed the presence of a 150 nm thick amorphous layer. These results are compared to similar investigations on geikielite (MgTiO{sub 3}) and spinel (MgAl{sub 2}O{sub 4}) to explore factors that may influence radiation damage response in oxides.

  1. Enhanced secondary ion emission with a bismuth cluster ion source

    Science.gov (United States)

    Nagy, G.; Walker, A. V.

    2007-04-01

    We have investigated the mechanism of secondary ion yield enhancement using Bin+ (n = 1-6) primary ions and three different samples - dl-phenylalanine, Irganox 1010 and polystyrene - adsorbed on Al, Si and Ag substrates. The largest changes in secondary ion yields are observed for Bi2+ and Bi3+ primary ions. Smaller increases in secondary ion yield are found using Bi4+, Bi5+ and Bi6+ projectiles. The secondary ion yield enhancements are generally larger on Si than on Al. Using Bin+ structures obtained from density functional theory (DFT) calculations we demonstrate that the yield enhancements cannot be explained by an increase in the deposited energy density (energy per area) into the substrate. These data show that the mechanism of Bin+ sputtering is very similar to that for Aun+ primary ion beams. When a polyatomic primary ion strikes the substrate, its constituent atoms are likely to remain near to each other, and so a substrate atom can be struck simultaneously by multiple atoms. The action of these multiple concerted impacts leads to efficient energy transfer in the near surface region and an increase in the number of secondary ions ejected from the surface. Such concerted impacts involve one, two or three projectile atoms, which explains well the nonlinear yield enhancements observed going from Bi+ to Bi2+ to Bi3+.

  2. STM study of ion tracks created in GaAs by GeV Xe ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Hida, A. E-mail: hida@exp.t.u-tokyo.ac.jp; Iwase, A.; Mera, Y.; Kambara, T.; Maeda, K

    2003-08-01

    Defect structures in p-type GaAs bulk crystals irradiated with 3.54 GeV Xe{sup 31+} ions were studied by scanning tunneling microscopy (STM) and scanning tunneling spectroscopy (STS). STM images of the cleavage (1 1 0) surfaces revealed the fine structure of a single ion track that consists of a long straight linear defect of {approx}5 nm in diameter sheathed with a thin fringe in bright contrast. Unexpectedly, the surrounding region was observed to be irregular in contrast to atomically resolved images in non-irradiated regions. The local density of states measured by STS indicates that the tracks are amorphous whereas the sheath and the surrounding sites retain crystalline structures. Some of the defect contrasts can be explained as due to the shift of the Fermi level and the variation of the LDOS in the energy bands. Though the tracks and the surrounding regions were unaffected by STM observations and STS measurements under mild imaging conditions (tunneling current < 1 nA), we found that the contrasts of the tracks are 'erased' when we scan the tracks with the STM tip at tunneling current greater than 2 nA. These facts strongly suggest that the defects introduced by GeV Xe ion irradiation are recovered by atomic motion enhanced by injection of tunneling current.

  3. Simulated spatial and temporal dependence of chromium concentration in pure Fe and Fesbnd 14%Cr under high dpa ion irradiation

    Science.gov (United States)

    Vörtler, K.; Mamivand, M.; Barnard, L.; Szlufarska, I.; Garner, F. A.; Morgan, D.

    2016-10-01

    In this work we develop an ab initio informed rate theory model to track the spatial and temporal evolution of implanted ions (Cr+) in Fe and Fesbnd 14%Cr during high dose irradiation. We focus on the influence of the specimen surface, the depth dependence of ion-induced damage, the damage rate, and the consequences of ion implantation, all of which influence the depth dependence of alloy composition evolving with continued irradiation. We investigate chemical segregation effects in the material by considering the diffusion of the irradiation-induced defects. Moreover, we explore how temperature, grain size, grain boundary sink strength, and defect production bias modify the resulting distribution of alloy composition. Our results show that the implanted ion profile can be quite different than the predicted SRIM implantation profile due to radiation enhanced transport and segregation.

  4. Ion irradiation effect of alumina and its luminescence

    Energy Technology Data Exchange (ETDEWEB)

    Aoki, Yasushi; Yamamoto, Shunya; Naramoto, Hiroshi [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment; My, N.T.

    1997-03-01

    The luminescence spectra of single crystalline alpha-alumina and ruby which has 0.02% of Cr{sub 2}O{sub 3} as a impurity, induced by 200 keV He{sup +} and Ar{sup +} irradiation were measured at room temperature as a function of irradiation dose. The analysis of the measured spectra showed the existence of three main luminescence features in the wavelength region of 250 to 350 nm, namely anionic color centers, F-center at 411 nm and F{sup +}-center at 330 nm and a band observed around 315 nm. As alpha-alumina was irradiated with He{sup +}, F-center and F{sup +}-center luminescence grew and decayed, but the behaviors of those were different from each other. It seems that a concentration quenching occurred on the F-center luminescence in the dose range above 1x10{sup 14} He/cm{sup 2}. Furthermore, F-center luminescence was strongly suppressed in ruby, compared with that in alumina. On the other hand, the luminescence band around 315 nm appeared only in the early stage of irradiation and did not show its growth part. The dose dependent behavior was similar to that of Cr{sup 3+} emission at 695 nm (R-line) in ruby in both cases of He{sup +} and Ar{sup +} irradiation. Based on the experimental results mentioned above, the processes of defect formation and excitation in alumina in the early stage of ion irradiation will be discussed. (author)

  5. Characterization of polymeric films subjected to lithium ion beam irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Groenewold, Gary S., E-mail: gary.groenewold@inl.gov [Idaho National Laboratory, 2351 North Boulevard, Idaho Falls, ID 83415-2208 (United States); Cannon, W. Roger; Lessing, Paul A. [Idaho National Laboratory, 2351 North Boulevard, Idaho Falls, ID 83415-2208 (United States); Avci, Recep; Deliorman, Muhammedin; Wolfenden, Mark [Image and Chemical Analysis Laboratory, Montana State University, Bozeman, MT 59717 (United States); Akers, Doug W.; Jewell, J. Keith; Zuck, Larry D. [Idaho National Laboratory, 2351 North Boulevard, Idaho Falls, ID 83415-2208 (United States)

    2013-02-01

    Highlights: ► Polyethylene glycol (PEG) and paraffinic polymers were subjected to Li ion irradiation. ► Small oligomers detected in irradiated PEG by electrospray ionization (ESI) mass spectrometry. ► Radiolytic scission observed in X-ray photoelectron and electrospray ionization mass spectra. ► Radiation modified paraffinics characterized by changes in non-ionic surfactant additives. ► Results suggest that extent of radiolysis, and radiolytic pathways can be inferred. -- Abstract: Two different polymeric materials that are candidate materials for use as binders for mixed uranium–plutonium oxide nuclear fuel pellets were subjected to Li ion beam irradiation, in order to simulate intense alpha irradiation. The materials (a polyethylene glycol 8000 and a microcrystalline wax) were then analyzed using a combination of mass spectrometry (MS) approaches and X-ray photoelectron spectroscopy (XPS). Samples of the irradiated PEG materials were dissolved in H{sub 2}O and then analyzed using electrospray ionization-MS, which showed the formation of a series of small oligomers in addition to intact large PEG oligomers. The small oligomers were likely formed by radiation-induced homolytic scissions of the C–O and C–C bonds, which furnish radical intermediates that react by radical recombination with H{sup ·} and OH{sup ·}. Surface analysis using SIMS revealed a heterogeneous surface that contained not only PEG-derived polymers, but also hydrocarbon-based entities that are likely surface contaminants. XPS of the irradiated PEG samples indicated the emergence of different carbon species, with peak shifts suggesting the presence of sp{sup 2} carbon atoms. Analysis of the paraffinic film using XPS showed the emergence of oxygen on the surface of the sample, and also a broadening and shifting of the C1s peak, demonstrating a change in the chemistry on the surface. The paraffinic film did not dissolve in either H{sub 2}O or a H{sub 2}O–methanol solution, and

  6. Microstructure of RERTR DU-Alloys Irradiated with Krypton Ions

    Energy Technology Data Exchange (ETDEWEB)

    J. Gan; D. Keiser; D. Wachs; B. Miller; T. Allen; M. Kirk; J. Rest

    2009-11-01

    Fuel development for reduced enrichment research and test reactor (RERTR) program is tasked with the development of new low enrichment uranium fuels that can be employed to replace existing high enrichment uranium fuels currently used in many research and test reactors worldwide. Radiation stability of the interaction product formed at fuel-matrix interface has a strong impact on fuel performance. Three depleted uranium alloys are cast that consist of the following 5 phases of interest to be investigated: U(Si,Al)3, (U,Mo)(Si,Al)3, UMo2Al20, U6Mo4Al43 and UAl4. Irradiation of TEM disc samples with 500 keV Kr ions at 200?C to high doses up to ~100 dpa were conducted using an intermediate voltage electron microscope equipped with an ion accelerator. The irradiated microstructure of the 5 phases is characterized using transmission electron microscopy. The results will be presented and the implication of the observed irradiated microstructure on the fuel performance will be discussed.

  7. Tailoring molybdenum nanostructure evolution by low-energy He+ ion irradiation

    Science.gov (United States)

    Tripathi, J. K.; Novakowski, T. J.; Hassanein, A.

    2015-10-01

    Mirror-finished polished molybdenum (Mo) samples were irradiated with 100 eV He+ ions as a function of ion fluence (using a constant flux of 7.2 × 1020 ions m-2 s-1) at normal incidence and at 923 K. Mo surface deterioration and nanoscopic fiber-form filament ("Mo fuzz") growth evolution were monitored by using field emission (FE) scanning electron (SEM) and atomic force (AFM) microscopy studies. Those studies confirm a reasonably clean and flat surface, up to several micrometer scales along with a few mechanical-polishing-induced scratches. However, He+ ion irradiation deteriorates the surface significantly even at 2.1 × 1023 ions m-2 fluence (about 5 min. irradiation time) and leads to evolution of homogeneously populated ∼75-nm-long Mo nanograins having ∼8 nm intergrain width. The primary stages of Mo fuzz growth, i.e., elongated half-cylindrical ∼70 nm nanoplatelets, and encapsulated bubbles of 20-45 nm in diameter and preferably within the grain boundaries of sub-micron-sized grains, were observed after 1.3 × 1024 ions m-2 fluence irradiation. Additionally, a sequential enhancement in the sharpness, density, and protrusions of Mo fuzz at the surface with ion fluence was also observed. Fluence- and flux-dependent studies have also been performed at 1223 K target temperature (beyond the temperature window for Mo fuzz formation). At a constant fluence of 2.6 × 1024 ions m-2, 7.2 × 1020 ions m-2 s-1 flux generates a homogeneous layered and stacked nanodiscs of ∼70 nm diameter. On the other hand, 1.2 × 1021 ions m-2 s-1 flux generates a combination of randomly patched netlike nanomatrix networked structure, mostly with ∼105 nm nanostructure wall width, various-shaped pores, and self-organized nano arrays. While the observed netlike nanomatrix network structures for 8.6 × 1024 ions m-2 fluence (at a constant flux of 1.2 × 1021 ions m-2 s-1) is quite similar to those for 2.6 × 1024 ions m-2 fluence, the nanostructure wall width extends up to ∼45

  8. Tailoring molybdenum nanostructure evolution by low-energy He{sup +} ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Tripathi, J.K., E-mail: jtripat@purdue.edu; Novakowski, T.J.; Hassanein, A.

    2015-10-30

    Mirror-finished polished molybdenum (Mo) samples were irradiated with 100 eV He{sup +} ions as a function of ion fluence (using a constant flux of 7.2 × 10{sup 20} ions m{sup −2} s{sup −1}) at normal incidence and at 923 K. Mo surface deterioration and nanoscopic fiber-form filament (“Mo fuzz”) growth evolution were monitored by using field emission (FE) scanning electron (SEM) and atomic force (AFM) microscopy studies. Those studies confirm a reasonably clean and flat surface, up to several micrometer scales along with a few mechanical-polishing-induced scratches. However, He{sup +} ion irradiation deteriorates the surface significantly even at 2.1 × 10{sup 23} ions m{sup −2} fluence (about 5 min. irradiation time) and leads to evolution of homogeneously populated ∼75-nm-long Mo nanograins having ∼8 nm intergrain width. The primary stages of Mo fuzz growth, i.e., elongated half-cylindrical ∼70 nm nanoplatelets, and encapsulated bubbles of 20–45 nm in diameter and preferably within the grain boundaries of sub-micron-sized grains, were observed after 1.3 × 10{sup 24} ions m{sup −2} fluence irradiation. Additionally, a sequential enhancement in the sharpness, density, and protrusions of Mo fuzz at the surface with ion fluence was also observed. Fluence- and flux-dependent studies have also been performed at 1223 K target temperature (beyond the temperature window for Mo fuzz formation). At a constant fluence of 2.6 × 10{sup 24} ions m{sup −2}, 7.2 × 10{sup 20} ions m{sup −2} s{sup −1} flux generates a homogeneous layered and stacked nanodiscs of ∼70 nm diameter. On the other hand, 1.2 × 10{sup 21} ions m{sup −2} s{sup −1} flux generates a combination of randomly patched netlike nanomatrix networked structure, mostly with ∼105 nm nanostructure wall width, various-shaped pores, and self-organized nano arrays. While the observed netlike nanomatrix network structures for 8.6 × 10{sup 24} ions m{sup −2} fluence (at a constant

  9. Effects of Heavy-ion Beams Irradiation on Survival Rate and Antioxidant Enzymes of Sweet Sorghum Seedlings

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    [Objective] This study aimed to investigate the effects of heavy-ion beams irradiation on the seed germination potential, survival rate, antioxidant enzyme activi- ties and lipid peroxidation of sweet sorghum. [Method] The dry seeds were irradiated by '2(36. heavy ion beams with absorbed doses: 0, 40, 80, 120, 160 and 200 Gy, respectively. Then, the seed germination potential, survival rate, antioxidant enzyme activities and lipid peroxidation of sweet sorghum were measured. [Result] Heavy-ion beams irradiation exhibited different influence on germination potential and survival rates. Germination rate showed a downward trend, but the corresponding survival curve of seedlings was saddle-shaped. The activities of SOD, POD, CAT and ASA- POD changed in different trends as well. The MDA content rose toward increasing irradiation dose, suggesting that high dose of heavy-ion beams irradiation enhanced the damage to membrane of sweet sorghum seedlings. [Conclusion] After being irra- diated, germination potential and survival rates of sweet sorghum were decreased, and antioxidant enzymes activity changed greatly. This study laid the basis for fur- ther work on breeding and improvement of sweet sorghum irradiated by ,^(12)C^(6+) heavy ion beams.

  10. Swift heavy ion irradiation of Pt nanocrystals: I. shape transformation and dissolution

    Energy Technology Data Exchange (ETDEWEB)

    Giulian, R.; Araujo, L.L.; Kluth, P.; Sprouster, D.J.; Schnohr, C.S.; Byrne, A.P.; Ridgway, M.C. (ANU)

    2014-09-24

    We report on the effects of swift heavy ion irradiation of embedded Pt nanocrystals (NCs), which change from spheres to prolate spheroids to rods upon irradiation. Using a broad range of ion irradiation energies and NC mean sizes we demonstrate that the elongation and dissolution processes are energy and size dependent, attaining comparable levels of shape transformation and dissolution upon a given energy density deposited in the matrix. The NC shape transformation remains operative despite discontinuous ion tracks in the matrix and exhibits a constant threshold size for elongation. In contrast, for ion irradiations in which the ion tracks are continuous, the threshold size for elongation is clearly energy dependent.

  11. Zirconium oxidation under high energy heavy ion irradiation

    CERN Document Server

    Bérerd, N; Moncoffre, N; Jaffrezic, H; Balanzat, E; democrite-00023380, ccsd

    2004-01-01

    This paper concerns the study of zirconium oxidation under irradiation with high energetic Xe ions. The irradiations were performed on the IRRSUD beam line at GANIL (Caen). The oxygen partial pressure was fixed at 10$^{-3}$ Pa and two temperature conditions were used, either 480$\\circ$C reached by Joule effect heating or 280$\\circ$C due to Xe energy deposition. Zirconia was fully characterized by Rutherford Backscattering Spectrometry, Transmission Electron Microscopy and Grazing Angle X-ray Diffraction. Apparent diffusion coefficients of oxygen in ZrO2 were determined from these experiments by using a model which takes into account a surface exchange between oxygen gas and the ZrO2 surface. These results are compared with thermal oxidation data.

  12. Space environmental durability of spacecrafts materials using ion beam irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Y. H.; Kim, D. W.; Lee, S. M.; Lee, I. T.; Ok, J. G. [Seoul Nat. Univ., Seoil (Korea, Republic of)

    2006-04-15

    Simulation of space proton effects by ion beam irradiation : due to diverse energy spectrums and fluxes of space protons are distributed in space according to the altitude and location in orbits, hard to simulate simply on the ground. JPL-1991 solar proton event is chosen to simulate the specific proton model. Cyclotrons for radiological treatments are utilized as main facility which can accelerate protons with MeV energy and possible to simulate the fluxes. Specimens are prepared with ITO aluminized polyimide Kapton and VDA Mylar. Mechanical, chemical changes analyses, and visual analysis of crystalline change : for assessment of mechanical properties of irradiated specimens, 50N micro tensile system is used for the ultimate tensile strength and elongation. Additional ESPI equipment can measure the elongation rate, yield strength, and elastic modulus. XPS is used for strength change from the molecular binding energy in crystal. SEM is also used for morphological visula analysis.

  13. Irradiation influence on Mylar and Makrofol induced by argon ions in a plasma immersion ion implantation system

    Energy Technology Data Exchange (ETDEWEB)

    Hassan, A. [Accelerators & Ion Sources Department, Nuclear Research Center, Atomic Energy Authority, P.O. 13759, Cairo (Egypt); El-Saftawy, A.A., E-mail: aama1978@yahoo.com [Accelerators & Ion Sources Department, Nuclear Research Center, Atomic Energy Authority, P.O. 13759, Cairo (Egypt); Aal, S.A. Abd El [Central Lab. for Elemental & Isotopic Analysis, Nuclear Research Center, Atomic Energy Authority, P.O. 13759, Cairo (Egypt); Ghazaly, M. El [Physiology Department, College of Medicine, Taif University, P.O. 888, Taif (Saudi Arabia); Physics Department, Faculty of Science, Zagazig University, P.O. 44519, Zagazig (Egypt)

    2015-08-30

    Highlights: • A home-built plasma immersion ion implantation system was tested in modifying surfaces. • Wettability modifications within the energy range 10 keV implantation are not investigated elsewhere, up to our knowledge. • The wettability of Mylar and Makrofol surface was enhanced by the dual effect of ion implantation and plasma treatment. • The improved wettability was found to depend on both surface roughness and chemistry. • The adhesive bonding and surface energy of the polymers are improved. - Abstract: Mylar and Makrofol polycarbonate polymers were irradiated by Ar ions in a plasma immersion ion implantation (PIII) system. The surface wettability of both polymers was investigated by employing the contact angle method. The measured contact angles were found to depend on the surface layer properties. Good wetting surfaces were found to depend not only on surface roughness but also on its chemistry that analyzed by Fourier transform infrared (FTIR) spectroscopy. Surfaces topography and roughness was investigated and correlated to their surface energy which studied with the aid of acid-base model for evaluating the improvement of surface wettability after irradiation. PIII improves polymers surface properties efficiently in a controllable way.

  14. Production and irradiation of ionic liquid cluster ions

    Energy Technology Data Exchange (ETDEWEB)

    Takaoka, Gikan H., E-mail: gtakaoka@kuee.kyoto-u.ac.jp [Photonics and Electronics Science and Engineering Center, Kyoto University, Katsura, Nishikyo-ku, Kyoto 615-8510 (Japan); Takeuchi, Mitsuaki; Ryuto, Hiromichi; Ueda, Ryo [Photonics and Electronics Science and Engineering Center, Kyoto University, Katsura, Nishikyo-ku, Kyoto 615-8510 (Japan)

    2013-07-15

    We have developed a field-emission-type of cluster ion source using ionic liquids such as 1-butyl-3-methylimidazolium hexafluorophosphate (BMIM-PF{sub 6}). The current obtained was stable by placing a porous cap around the emitter. Time-of-flight (TOF) measurement showed that the peak mass number was approximately 5000 for positive and negative BMIM-PF{sub 6} ion beams. This indicated that BMIM-PF{sub 6} clusters with a size of a few tens of molecules were produced. With regard to the surface modification by BMIM-PF{sub 6} ion beams, positive and negative cluster ion beams were used to irradiate Si(1 0 0) and glass substrates. Scanning electron microscope (SEM) and atomic force microscope (AFM) observations showed that the surface roughness of substrates increased. Furthermore, X-ray photoelectron spectroscopy (XPS) measurement showed that the composition ratio of layers deposited by positive or negative cluster ion beams was similar to that of BMIM-PF{sub 6} solvent.

  15. Production and irradiation of ionic liquid cluster ions

    Science.gov (United States)

    Takaoka, Gikan H.; Takeuchi, Mitsuaki; Ryuto, Hiromichi; Ueda, Ryo

    2013-07-01

    We have developed a field-emission-type of cluster ion source using ionic liquids such as 1-butyl-3-methylimidazolium hexafluorophosphate (BMIM-PF6). The current obtained was stable by placing a porous cap around the emitter. Time-of-flight (TOF) measurement showed that the peak mass number was approximately 5000 for positive and negative BMIM-PF6 ion beams. This indicated that BMIM-PF6 clusters with a size of a few tens of molecules were produced. With regard to the surface modification by BMIM-PF6 ion beams, positive and negative cluster ion beams were used to irradiate Si(1 0 0) and glass substrates. Scanning electron microscope (SEM) and atomic force microscope (AFM) observations showed that the surface roughness of substrates increased. Furthermore, X-ray photoelectron spectroscopy (XPS) measurement showed that the composition ratio of layers deposited by positive or negative cluster ion beams was similar to that of BMIM-PF6 solvent.

  16. Changes in Storage Properties of Hydrides Induced by Ion Irradiation

    Directory of Open Access Journals (Sweden)

    Jasmina GRBOVIĆ NOVAKOVIĆ

    2013-05-01

    Full Text Available The influence of structural changes caused by irradiation with different ions, their energies and fluences on sorption properties has been investigated. Results suggest that there are several mechanisms of desorption depending on defect concentration, their interaction and ordering. It has been also demonstrated that the changes in near-surface area play the crucial role in hydrogen desorption kinetics. It is confirmed that there is possibility to control the thermodynamic parameters of these systems by controlling vacancies depth profile and concentration. DOI: http://dx.doi.org/10.5755/j01.ms.19.2.1579

  17. Track creation after swift heavy ion irradiation of insulators

    Science.gov (United States)

    Medvedev, N.; Osmani, O.; Rethfeld, B.; Schleberger, M.

    2010-10-01

    The dynamics of structural modifications of insulators irradiated with swift heavy ions were investigated theoretically applying a combination of Monte-Carlo method (MC), used to describe SHI penetration and following excitation and relaxation of the electronic subsystem, with Two Temperature Model (TTM) describing the heating of the lattice. This MC-TTM combination demonstrates that secondary ionizations play a very important role for the track formation process. They lead to an additional term in the heat diffusion equation related to energy stored in the hole subsystem. This storage of energy causes a significant delay of heating and prolongs the timescales up to tens of picoseconds.

  18. The influence of carbon ion irradiation on sweet sorghum seeds

    Energy Technology Data Exchange (ETDEWEB)

    Dong, X.C. [Radiobiology Department, Institute of Modern Physics, Chinese Academy of Sciences, Nanchang Road 509, Lanzhou 730000 (China); Graduate School of Chinese Academy of Science, 19 Yuquan Road, Beijing 100040 (China)], E-mail: dongxicun@impcas.ac.cn; Li, W.J. [Radiobiology Department, Institute of Modern Physics, Chinese Academy of Sciences, Nanchang Road 509, Lanzhou 730000 (China)], E-mail: wjli@impcas.ac.cn; Liu, Q.F.; He, J.Y.; Yu, L.X.; Zhou, L.B.; Qu, Y.; Xie, H.M. [Radiobiology Department, Institute of Modern Physics, Chinese Academy of Sciences, Nanchang Road 509, Lanzhou 730000 (China)

    2008-01-15

    The aim of this study is to investigate the effects of different doses of 100 MeV/u carbon ions on sweet sorghum seeds in order to improve crop yields and their sugar content. After irradiation, seeds were germinated and grown to 30 days, and others were sown in the field. At the end of harvesting season all planted seeds were picked separately and M2 generations obtained. The differences among the treatments were examined using the RAPD procedure. In the study done by using 38 primers; according to the amplification results, the differences among the various doses treatment were shown.

  19. The influence of carbon ion irradiation on sweet sorghum seeds

    Science.gov (United States)

    Dong, X. C.; Li, W. J.; Liu, Q. F.; He, J. Y.; Yu, L. X.; Zhou, L. B.; Qu, Y.; Xie, H. M.

    2008-01-01

    The aim of this study is to investigate the effects of different doses of 100 MeV/u carbon ions on sweet sorghum seeds in order to improve crop yields and their sugar content. After irradiation, seeds were germinated and grown to 30 days, and others were sown in the field. At the end of harvesting season all planted seeds were picked separately and M2 generations obtained. The differences among the treatments were examined using the RAPD procedure. In the study done by using 38 primers; according to the amplification results, the differences among the various doses treatment were shown.

  20. Changes in Storage Properties of Hydrides Induced by Ion Irradiation

    Directory of Open Access Journals (Sweden)

    Jasmina GRBOVIĆ NOVAKOVIĆ

    2013-05-01

    Full Text Available The influence of structural changes caused by irradiation with different ions, their energies and fluences on sorption properties has been investigated. Results suggest that there are several mechanisms of desorption depending on defect concentration, their interaction and ordering. It has been also demonstrated that the changes in near-surface area play the crucial role in hydrogen desorption kinetics. It is confirmed that there is possibility to control the thermodynamic parameters of these systems by controlling vacancies depth profile and concentration. DOI: http://dx.doi.org/10.5755/j01.ms.19.2.1579

  1. Deuterium trapping at defects created with neutron and ion irradiations in tungsten

    Energy Technology Data Exchange (ETDEWEB)

    Y. Hatano; M. Shimada; T. Otsuka; Y. Oya; V.Kh. Alimov; M. Hara; J. Shi; M. Kobayashi; T. Oda; G. Cao; K. Okuno; T. Tanaka; K. Sugiyama; J. Roth; B. Tyburska-Püschel; J. Dorner; N. Yoshida; N. Futagami; H. Watanabe; M. Hatakeyama; H. Kurishita; M. Sokolov; Y. Katoh

    2013-07-01

    The effects of neutron and ion irradiations on deuterium (D) retention in tungsten (W) were investigated. Specimens of pure W were irradiated with neutrons to 0.3 dpa at around 323 K and then exposed to high-flux D plasma at 473 and 773 K. The concentration of D significantly increased by neutron irradiation and reached 0.8 at% at 473 K and 0.4 at% at 773 K. Annealing tests for the specimens irradiated with 20 MeV W ions showed that the defects which play a dominant role in the trapping at high temperature were stable at least up to 973 K, while the density decreased at temperatures equal to or above 1123 K. These observations of the thermal stability of traps and the activation energy for D detrapping examined in a previous study (˜1.8 eV) indicated that the defects which contribute predominantly to trapping at 773 K were small voids. The higher concentration of trapped D at 473 K was explained by additional contributions of weaker traps. The release of trapped D was clearly enhanced by the exposure to atomic hydrogen at 473 K, though higher temperatures are more effective for using this effect for tritium removal in fusion reactors.

  2. Modifications induced in the polycarbonate Makrofol KG polymer by Li (50 MeV) ion irradiation

    Indian Academy of Sciences (India)

    Jaskiran Kaur; S K Chakarvarti; D Kanjilal; Surinder Singh

    2009-04-01

    Swift heavy ions interact predominantly through inelastic scattering while traversing any polymer medium and produce excited/ionized atoms. Here samples of the polycarbonate Makrofol of approximate thickness 20 m, spin coated on GaAs substrate were irradiated with 50 MeV Li ion (+3 charge state). Build-in modifications due to irradiation were studied using FTIR and XRD characterizations. Considerable changes have been observed in the polymer while varying the fluence from 1E11 ion/cm2 to 1E13 ion/cm2 Li ions. AFM images of the surface modifications caused by ion irradiation on the polymer are also presented.

  3. Ion-irradiation-induced hardening in Inconel 718

    Science.gov (United States)

    Hunn, J. D.; Lee, E. H.; Byun, T. S.; Mansur, L. K.

    2001-07-01

    Inconel 718 is a material under consideration for areas in the target region of the spallation neutron source (SNS), now under construction at Oak Ridge National Laboratory (ORNL) in the US. In these positions, displacement damage from protons and neutrons will affect the mechanical properties. In addition, significant amounts of helium and hydrogen will build up in the material due to transmutation reactions. Nanoindentation measurements of solution-annealed (SA) Inconel 718 specimens, implanted with Fe-, He-, and H-ions to simulate SNS target radiation conditions, have shown that hardening occurs due to ion-induced displacement damage as well as due to the build-up of helium bubbles in the irradiated layer. Precipitation-hardened (PH) Inconel 718 also exhibited hardening by helium build-up but showed softening as a function of displacement damage due to dissolution of the γ ' and γ″ precipitates.

  4. Helium release and amorphization resistance in ion irradiated nanochannel films

    Science.gov (United States)

    Hong, Mengqing; Wang, Yongqiang; Ren, Feng; Zhang, Hongxiu; Fu, Dejun; Yang, Bing; Xiao, Xiangheng; Jiang, Changzhong

    2014-04-01

    Volumetric swelling, surface blistering, exfoliation and embrittlement partially induced by the aggregation of gas bubbles are serious problems for materials in nuclear reactors. This letter demonstrates that the “vein-like” nanochannel films possess greater He management capability and radiation tolerance. For a given fluence, the He bubble size in the nanochannel film decreases with increasing the nanochannel density. For a given nanochannel density, the bubble size increases with increasing fluence initially but levels off to a maximum value of 0.8 nm after the ion fluence reaches 2\\times10^{17}\\ \\text{ions/cm}^{2} , corresponding to He release ratio of 79% in the irradiated CrN RT films. The abundant surfaces in the nanochannel films are perfect defect sinks and thereby large sized He bubbles and supersaturated defects are less likely to be developed in these high radiation tolerant materials.

  5. Behavior of nuclear materials irradiated with a dual ion beam

    Science.gov (United States)

    Thomé, Lionel; Velişa, Gihan; Debelle, Aurélien; Miro, Sandrine; Garrido, Frédérico; Trocellier, Patrick; Serruys, Yves

    2014-05-01

    Synergistic effects of nuclear (Sn) and electronic (Se) energy losses are investigated by comparing the damage accumulated in selected oxide (c-ZrO2, MgO, Gd2Ti2O7) and carbide (SiC) single crystals irradiated with single and dual low and high energy ion beams. Channeling results show that the Sn/Se synergy induces a strong decrease of the damage in MgO and SiC (where amorphization is prevented) and almost no effects in c-ZrO2 and Gd2Ti2O7. Raman and TEM results confirm this statement. The healing of defects generated by nuclear collisions in MgO and SiC is due to the electronic excitation produced in the wake of swift ions. These results present a strong interest for technological applications in the nuclear industry where expected cooperative Sn/Se effects may preserve the integrity of nuclear materials.

  6. Texture coefficient analysis of ion beam irradiated copper nanowires

    Energy Technology Data Exchange (ETDEWEB)

    Rana, Pallavi, E-mail: prana.phy@gmail.com; Chaudhary, Ritika, E-mail: chauhanrpc@gmail.com; Chauhan, R. P. [Department of Physics, National Institute of Technology, Kurukshetra-136119 (India)

    2016-05-23

    Radiation may deteriorate physical properties of the materials and leave negative as well as positive impacts especially on crystalline materials. The energy deposited by ions to the grains and grain boundaries could also influence other properties of grains like: strain, reflection of charge carriers from grain boundaries, in addition to their grain size and orientation. The intensity of a peak in the XRD spectra is the direct reflection of orientation of a miller plane in the crystal. The increased intensity symbolizes the crystalline behavior due to defects annealing, while decreased intensity portray the defects formation and slender amorphisation. Orientation distribution function is a probability distribution function that quantified the texture of a polycrystalline material. The coefficients of harmonic expansion of orientation distribution function is the measurement of the texture coefficient ‘TC’. This study focused on the investigation of effect of ion beam irradiation on the preffered orientation of the planes of copper nanowires.

  7. Modifications in structure and optical property of Cu nanoparticles in SiO{sub 2} by post heavy ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Changlong, E-mail: liuchanglong@tju.edu.cn [School of Science, Tianjin University, Tianjin 300072 (China); Tianjin Key Laboratory of Low Dimensional Materials Physics and Preparing Technology, Institute of Advanced Materials Physics, Faculty of Science, Tianjin 300072 (China); Key Laboratory of Beam Technology and Material Modification of Ministry of Education, Beijing Normal University, Beijing 100875 (China); Wang, Nana; Wang, Jun; Liu, Huixian; Jia, Guangyi; Mu, Xiaoyu [School of Science, Tianjin University, Tianjin 300072 (China)

    2014-05-01

    The implantation-synthesized Cu nanoparticles (NPs) in silica were irradiated with 500 keV Xe and Ar ions, respectively. After Xe ion irradiation at a fluence of 2 × 10{sup 16}/cm{sup 2}, the average diameter of Cu NPs was increased from 7.3 to 8.5 nm, and especially, Cu NPs with a diameter of 11–14 nm were formed beyond the projected range of Cu ions and nearly aligned at the same depth, which presented a higher volume fraction. As a result, the Cu surface plasmon resonance (SPR) absorption peak was enhanced. However, if Xe ion fluence was less than 1 × 10{sup 16}/cm{sup 2}, no clear variation of the Cu SPR absorption peak could be found. Further, it was also revealed that Xe ion irradiation caused the Cu SPR absorption peak to more drastically change than Ar ion irradiation at the same ion fluence. The underlying processes for the above findings were discussed and tentatively proposed.

  8. Resonant absorption effects induced by polarized laser light irradiating thin foils in the TNSA regime of ion acceleration

    Science.gov (United States)

    Torrisi, L.; Badziak, J.; Rosinski, M.; Zaras-Szydlowska, A.; Pfeifer, M.; Torrisi, A.

    2016-04-01

    Thin foils were irradiated by short pulsed lasers at intensities of 1016-19W/cm2 in order to produce non-equilibrium plasmas and ion acceleration from the target-normal-sheath-acceleration (TNSA) regime. Ion acceleration in forward direction was measured by SiC detectors and ion collectors used in the time-of-flight configuration. Laser irradiations were employed using p-polarized light at different incidence angles with respect to the target surface and at different focal distances from the target surface. Measurements demonstrate that resonant absorption effects, due to the plasma wave excitations, enhance the plasma temperature and the ion acceleration with respect to those performed without to use of p-polarized light. Dependences of the ion flux characteristics on the laser energy, wavelength, focal distance and incidence angle will be reported and discussed.

  9. Non-ohmic resistive state in ion-irradiated YBa sub 2 Cu sub 3 O sub 7-x

    Energy Technology Data Exchange (ETDEWEB)

    Iwase, A.; Masaki, N.; Iwata, T. (Dept. of Physics, Japan Atomic Energy Research Inst., Ibaraki (Japan)); Nihira, T. (Faculty of Engineering, Ibaraki Univ. (Japan))

    1991-03-15

    We have studied the effect of 120 MeV {sup 16}O ion irradiation on the non-ohmic electrical resistive state at 77.3 K in YBa{sub 2}Cu{sub 3}O{sub 7-x}. For small measuring currents, the voltage V varies as a power of the current I and the ion-fluence PHI, i.e. Vproportional to I{sup n} and Vproportional to PHI{sup m}, where the exponents n and m are functions of the ion-fluence and the current, respectively. For larger currents, the voltage obeys another power-law: Vproportional to Isup(n'), where n' is lower than n at a given ion-fluence. Analysis of the experimental data using a model current-induced unbinding of thermally excited vortex pairs shows that ion-irradiations cause the enhancement of dissociation of the bound vortex-antivortex pairs. (orig.).

  10. Ion irradiation induced disappearance of dislocations in a nickel-based alloy

    Energy Technology Data Exchange (ETDEWEB)

    Chen, H.C.; Li, D.H.; Lui, R.D.; Huang, H.F.; Li, J.J.; Lei, G.H.; Huang, Q.; Bao, L.M.; Yan, L., E-mail: yanlong@sinap.ac.cn; Zhou, X.T., E-mail: zhouxingtai@sinap.ac.cn; Zhu, Z.Y.

    2016-06-15

    Under Xe ion irradiation, the microstructural evolution of a nickel based alloy, Hastelloy N (US N10003), was studied. The intrinsic dislocations are decorated with irradiation induced interstitial loops and/or clusters. Moreover, the intrinsic dislocations density reduces as the irradiation damage increases. The disappearance of the intrinsic dislocations is ascribed to the dislocations climb to the free surface by the absorption of interstitials under the ion irradiation. Moreover, the in situ annealing experiment reveals that the small interstitial loops and/or clusters induced by the ion irradiation are stable below 600 °C.

  11. Study of Mutagenic Effects of M1 Generation of Maize Seeds Irradiated by Heavy Ions

    Institute of Scientific and Technical Information of China (English)

    LUOHong-bing; ZHAOKui; GUOJi-yu; SUILi; NIMei-nan; MEIJun-ping; LUXiu-qin; ZHOUPing; KONGFu-quan; ZHANGGen-fa

    2003-01-01

    In order to study M1 biological effects induced by heavy ion irradiation on maize seeds, the embryos of dry maize seeds are irradiated with 7Li and 12C ions. The experiment is performed at the heavy ion scanning tube of the HI-13 tandem accelerator. The beam goes through a thickness of 25μm. Then the maize seeds are irradiated in the air uniformly.

  12. Strong out-of-plane magnetic anisotropy in ion irradiated anatase TiO2 thin films

    Directory of Open Access Journals (Sweden)

    M. Stiller

    2016-12-01

    Full Text Available The temperature and field dependence of the magnetization of epitaxial, undoped anatase TiO2 thin films on SrTiO3 substrates was investigated. Low-energy ion irradiation was used to modify the surface of the films within a few nanometers, yet with high enough energy to produce oxygen and titanium vacancies. The as-prepared thin film shows ferromagnetism which increases after irradiation with low-energy ions. An optimal and clear magnetic anisotropy was observed after the first irradiation, opposite to the expected form anisotropy. Taking into account the experimental parameters, titanium vacancies as di-Frenkel pairs appear to be responsible for the enhanced ferromagnetism and the strong anisotropy observed in our films. The magnetic impurities concentrations was measured by particle-induced X-ray emission with ppm resolution. They are ruled out as a source of the observed ferromagnetism before and after irradiation.

  13. Swift heavy ion irradiation effect on Cu-doped CdS nanocrystals embedded in PMMA

    Indian Academy of Sciences (India)

    Shweta Agrawal; Subodh Srivastava; Sumit Kumar; S S Sharma; B Tripathi; M Singh; Y K Vijay

    2009-12-01

    Semiconductor nanocrystals (NCs) have received much interest for their optical and electronic properties. When these NCs dispersed in polymer matrix, brightness of the light emission is enhanced due to their quantum dot size. The CdCuS NCs have been synthesized by chemical route method and then dispersed in PMMA matrix. These nanocomposite polymer films were irradiated by swift heavy ion (SHI) (100 MeV, Si+7 ions beam) at different fluences of 1 × 1010 and 1 × 1012 ions/cm2 and then compared their structural and optical properties by XRD, atomic force microscopy, photoluminescence, and UV-Vis spectroscopy before and after irradiation. The XRD spectra showed a broad hump around 2 ≈ 11.83° due to amorphous PMMA and other peaks corresponding to hexagonal structure of CdS nanocrystals in PMMA matrix. The photoluminescence spectra shows a broad peak at 530 nm corresponding to green emission due to Cu impurities in CdS. The UV-Vis measurement showed red shift in optical absorption and bandgap changed from 4.38–3.60 eV as the irradiation fluency increased with respect to pristine CdCuS nanocomposite polymer film.

  14. Crystallographic analysis of amorphization caused by ion irradiation

    CERN Document Server

    Nakagawa, S T; Ono, T; Hada, Y; Betz, G

    2003-01-01

    Ion irradiation often causes amorphization in a crystal. We have presented a new crystallographic analysis that defines a new type of order parameter, which we call pixel mapping (PM). PM can describe algebraically to what extent and how the crystallinity has changed under ion bombardment. In other words, PM describes the long-range-order (LRO) interactions, based on the crystallography. PM can be effectively used, when it is incorporated in a classical molecular dynamics (MD) calculation. In the case of B ions implanted into a Si crystal, we observed crystal to amorphous (CA) transitions under energetic ion bombardment at low temperature. The PM profiling was more effective to reveal the CA transition than other atomistic methods of analyses as radial distribution function g(r) or vacancy mapping N sub v. PM could distinguish between perfect crystalline states, transition states, and random states. Moreover, PM revealed that the lattice reaction was cooperative even in a mesoscopic volume, e.g. in a cube of ...

  15. Simulation of alpha decay of actinides in iron phosphate glasses by ion irradiation

    Science.gov (United States)

    Dube, Charu L.; Stennett, Martin C.; Gandy, Amy S.; Hyatt, Neil C.

    2016-03-01

    A surrogate approach of ion beam irradiation is employed to simulate alpha decay of actinides in iron phosphate nuclear waste glasses. Bismuth and helium ions of different energies have been selected for simulating glass matrix modification owing to radiolysis and ballistic damage due to recoil atoms. Structural modification and change in coordination number of network former were probed by employing Reflectance Fourier-Transform Infrared (FT-IR), and Raman spectroscopies as a consequence of ion irradiation. Depolymerisation is observed in glass sample irradiated at intermediate energy of 2 MeV. Helium blisters of micron size are seen in glass sample irradiated at low helium ion energy of 30 keV.

  16. Irradiation damage simulation of Zircaloy-4 using argon ions bombardment

    Institute of Scientific and Technical Information of China (English)

    Dequan Peng; Xinde Bai; Feng Pan

    2008-01-01

    To simulate irradiation damage, argon ion was implanted in the Zircaloy-4 with the fluence ranging from 1×1016 to 1×1017 cm-2, using accelerating implanter at an extraction voltage of 190 kV and liquid nitrogen temperature. Then the influence of argon ion implantation on the aqueous corrosion behavior of Zircaloy-4 was studied. The valence states of elements in the surface layer of the samples wcrc analyzed using X-ray photoelectron spectroscopy (XPS). Transmission clcctron microscopy (TEM) was used to examine the microstructure of the argon-implanted samples. The potentiodynamic polarization technique was employed to evaluate the aqueous corrosion resistance of implanted Zircaloy-4 in 1 mol/L H2SO4 solution. It is found that there appear bubbles on the surface of the samples when the argon flucncc is 1×1016 cm-2. The microstructure of argon-implanted samples changes from amor-phous to partial amorphous, then to polycrystallinc, and again to amorphous. The corrosion resistance of implanted samples linearly declines with the increase of flucnce approximately, which is attributed to the linear increase of the irradiation damage.

  17. Lithium ion irradiation of standard and oxygenated silicon diodes

    CERN Document Server

    Candelori, A; Bisello, D; Giubilato, P; Kaminski, A; Litovchenko, A P; Lozano, A; Petrie, J R; Rando, R; Ullán, M; Wyss, J

    2004-01-01

    The next generation silicon detectors for future very high luminosity colliders or a possible LHC upgrade scenario will require radiation- hard detectors for fluences up to 10/sup 16/ 1-MeV equivalent neutrons/cm/sup 2/. These high fluences present strong constraints because long irradiation times are required at the currently available proton irradiation facilities. Energetic (58 MeV) lithium ions present a non-ionizing energy loss approximately=27.3 times higher than 27 MeV protons, and could consequently be a new promising radiation source for investigating the radiation hardness of silicon detectors up to very high particle fluences. Starting from this premise, we have investigated the degradation, as measured by the leakage current density increase and depletion voltage variations in the short and long-term characteristics, induced by 58 MeV Li ions in state-of-the-art silicon diodes processed by two different manufacturers on standard and oxygenated silicon substrates. Finally, the correlation between t...

  18. Amorphisation of boron carbide under slow heavy ion irradiation

    Science.gov (United States)

    Gosset, D.; Miro, S.; Doriot, S.; Moncoffre, N.

    2016-08-01

    Boron carbide B4C is widely used as a neutron absorber in nuclear plants. Most of the post-irradiation examinations have shown that the structure of the material remains crystalline, in spite of very high atomic displacement rates. Here, we have irradiated B4C samples with 4 MeV Au ions with different fluences at room temperature. Transmission electron microscopy (TEM) and Raman spectroscopy have been performed. The Raman analyses show a high structural disorder at low fluence, around 10-2 displacements per atoms (dpa). However, the TEM observations show that the material remains crystalline up to a few dpa. At high fluence, small amorphous areas a few nanometers large appear in the damaged zone but the long range order is preserved. Moreover, the size and density of the amorphous zones do not significantly grow when the damage increases. On the other hand, full amorphisation is observed in the implanted zone at a Au concentration of about 0.0005. It can be inferred from those results that short range and long range damages arise at highly different fluences, that heavy ions implantation has drastic effects on the structure stability and that in this material self-healing mechanisms are active in the damaged zone.

  19. Swift heavy ion irradiation reduces porous silicon thermal conductivity

    Energy Technology Data Exchange (ETDEWEB)

    Massoud, M.; Canut, B. [Université de Lyon, Institut des Nanotechnologies de Lyon INL-UMR5270, CNRS, INSA de Lyon, F-69621 Villeurbanne (France); Newby, P.; Frechette, L. [Centre de Recherche en Nanofabrication et Nanocaractérisation (CNR2), Université de Sherbrooke, Sherbrooke, Québec (Canada); Chapuis, P.O. [Université de Lyon, Centre de Thermique de Lyon CETHIL-UMR5008, CNRS, INSA de Lyon, F-69621 Villeurbanne (France); Bluet, J.M. [Université de Lyon, Institut des Nanotechnologies de Lyon INL-UMR5270, CNRS, INSA de Lyon, F-69621 Villeurbanne (France)

    2014-12-15

    While the electrical conductivity of semiconductors can be easily changed over order of magnitudes (8 in silicon) by playing on the doping, the thermal conductivity (TC) control is a challenging issue. Nevertheless, numerous applications require TC control in Si down to 1 W m{sup −1} K{sup −1}. Among them, there are thermal insulation requirements in MEMS, thermal management issues in 3D packaging or TC reduction for thermoelectric applications. Towards this end, the formation of nanoporous Si by electrochemical anodisation is efficient. Nevertheless, in this case the material is too fragile for MEMS application or even to withstand CMOS technological processes. In this work, we show that ion irradiation in the electronic regime is efficient for reducing TC in meso-porous Si (PSi), which is more mechanically robust than the nanoporous PSi. We have studied three different mass to energy ratios ({sup 238}U at 110 MeV and {sup 130}Xe at 91 MeV and 29 MeV) with fluences ranging from 10{sup 12} cm{sup −2} to 7 × 10{sup 13} cm{sup −2}. The sample properties, after irradiation, have been measured by infrared spectroscopy, Raman spectroscopy and scanning electron microscopy. The TC has been measured using scanning thermal microscopy. Although, bulk Si is insensitive to ion interaction in the electronic regime, we have observed the amorphisation of the PSi resulting in a TC reduction even for the low dose and energy. For the highest irradiation dose a very important reduction factor of four was obtained.

  20. Depth distribution of Frank loop defects formed in ion-irradiated stainless steel and its dependence on Si addition

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Dongyue, E-mail: dychen@safety.n.t.u-tokyo.ac.jp [The University of Tokyo, Department of Nuclear Engineering and Management, School of Engineering, 7-3-1 Hongo Bunkyo-ku, Tokyo 113-8656 (Japan); Murakami, Kenta [The University of Tokyo, Nuclear Professional School, School of Engineering, 2-22 Shirakata-Shirane, Tokai-mura, Ibaraki 319-1188 (Japan); Dohi, Kenji; Nishida, Kenji; Soneda, Naoki [Central Research Institute of Electric Power Industry, 2-11-1 Iwado-kita, Komae, Tokyo 201-8511 (Japan); Li, Zhengcao, E-mail: zcli@tsinghua.edu.cn [Tsinghua University, School of Materials Science and Engineering, Beijing 100084 (China); Liu, Li; Sekimura, Naoto [The University of Tokyo, Department of Nuclear Engineering and Management, School of Engineering, 7-3-1 Hongo Bunkyo-ku, Tokyo 113-8656 (Japan)

    2015-12-15

    Although heavy ion irradiation is a good tool to simulate neutron irradiation-induced damages in light water reactor, it produces inhomogeneous defect distribution. Such difference in defect distribution brings difficulty in comparing the microstructure evolution and mechanical degradation between neutron and heavy ion irradiation, and thus needs to be understood. Stainless steel is the typical structural material used in reactor core, and could be taken as an example to study the inhomogeneous defect depth distribution in heavy ion irradiation and its influence on the tested irradiation hardening by nano-indentation. In this work, solution annealed stainless steel model alloys are irradiated by 3 MeV Fe{sup 2+} ions at 400 °C to 3 dpa to produce Frank loops that are mainly interstitial in nature. The silicon content of the model alloys is also tuned to change point defect diffusion, so that the loop depth distribution influenced by diffusion along the irradiation beam direction could be discussed. Results show that in low Si (0% Si) and base Si (0.42% Si) samples the depth distribution of Frank loop density quite well matches the dpa profile calculated by the SRIM code, but in high Si sample (0.95% Si), the loop number density in the near-surface region is very low. One possible explanation could be Si’s role in enhancing the effective vacancy diffusivity, promoting recombination and thus suppressing interstitial Frank loops, especially in the near-surface region, where vacancies concentrate. By considering the loop depth distribution, the tested irradiation hardening is successfully explained by the Orowan model. A hardening coefficient of around 0.30 is obtained for all the three samples. This attempt in interpreting hardening results may make it easier to compare the mechanical degradation between different irradiation experiments.

  1. Ag ion irradiated based sensor for the electrochemical determination of epinephrine and 5-hydroxytryptamine in human biological fluids

    Energy Technology Data Exchange (ETDEWEB)

    Goyal, Rajendra N., E-mail: rngcyfcy@iitr.ernet.in [Department of Chemistry, Indian Institute of Technology Roorkee, Roorkee 247667 (India); Agrawal, Bharati [Department of Chemistry, Indian Institute of Technology Roorkee, Roorkee 247667 (India)

    2012-09-19

    Highlights: Black-Right-Pointing-Pointer Ag ions irradiation enhances the electrocatalytic activity of carbon nano tubes. Black-Right-Pointing-Pointer The low fluence of irradiation caused the ordering of carbon nano tubes. Black-Right-Pointing-Pointer Simultaneous determination of epinephrine and 5-hydroxytryptamine has been carried out. Black-Right-Pointing-Pointer The determination of the neurotransmitters in human blood and urine is reported. - Abstract: A promising and highly sensitive voltammetric method has been developed for the first time for the determination of epinephrine (EP) and 5-hydroxytryptamine (5-HT) using 120 MeV Ag ion irradiated multi-walled carbon nano tube (MWCNT) based sensor. The MWCNT were irradiated at various fluences of 1e12, 3e12 and 1e13 ions cm{sup -2} using palletron accelerator. The simultaneous determination of EP and 5-HT has been carried out in phosphate buffer solution of pH 7.20 using square wave voltammetry and cyclic voltammetry. Experimental results suggested that irradiation of MWCNT by Ag ions enhanced the electrocatalytic activity due to increase in effective surface area and insertion of Ag ions, leading to a remarkable enhancement in peak currents and shift of peak potentials to less positive values as compared to the unirradiated MWCNT (pristine). The developed sensor exhibited a linear relationship between peak current and concentration of EP and 5-HT in the range 0.1-105 {mu}M with detection limit (3{sigma}/b) of 2 nM and 0.75 nM, respectively. The practical utility of irradiation based MWCNT sensor has been demonstrated for the determination of EP and 5-HT in human urine and blood samples.

  2. Simulation of alpha decay of actinides in iron phosphate glasses by ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Dube, Charu L., E-mail: dubecharu@gmail.com; Stennett, Martin C.; Gandy, Amy S.; Hyatt, Neil C.

    2016-03-15

    Highlights: • Alpha decay of actinides in iron phosphate glasses is simulated by employing ion irradiation technique. • FTIR and Raman spectroscopic measurements confirm modification of glass network. • The depolymerisation of glass network after irradiation is attributed to synergetic effect of nuclear and electronic losses. - Abstract: A surrogate approach of ion beam irradiation is employed to simulate alpha decay of actinides in iron phosphate nuclear waste glasses. Bismuth and helium ions of different energies have been selected for simulating glass matrix modification owing to radiolysis and ballistic damage due to recoil atoms. Structural modification and change in coordination number of network former were probed by employing Reflectance Fourier-Transform Infrared (FT-IR), and Raman spectroscopies as a consequence of ion irradiation. Depolymerisation is observed in glass sample irradiated at intermediate energy of 2 MeV. Helium blisters of micron size are seen in glass sample irradiated at low helium ion energy of 30 keV.

  3. Electron beam irradiation of gemstone for color enhancement

    Energy Technology Data Exchange (ETDEWEB)

    Idris, Sarada; Ghazali, Zulkafli; Hashim, Siti A' iasah; Ahmad, Shamshad; Jusoh, Mohd Suhaimi [Malaysian Nuclear Agency, Bangi, Selangor (Malaysia); School of Chemicals and Material Engineering, NUST Islamabad (Pakistan); Malaysian Nuclear Agency, Bangi, Selangor (Malaysia)

    2012-09-26

    Numerous treatment of gemstones has been going on for hundreds of years for enhancing color and clarity of gems devoid of these attributes. Whereas previous practices included fraudulent or otherwise processes to achieve the color enhancement, the ionizing radiation has proven to be a reliable and reproducible technique. Three types of irradiation processes include exposure to gamma radiation, electron beam irradiation and the nuclear power plants. Electron Beam Irradiation of Gemstone is a technique in which a gemstone is exposed to highly ionizing radiation electron beam to knock off electrons to generate color centers culminating in introduction of deeper colors. The color centers may be stable or unstable. Below 9MeV, normally no radioactivity is introduced in the exposed gems. A study was conducted at Electron Beam Irradiation Centre (Alurtron) for gemstone color enhancement by using different kind of precious gemstones obtained from Pakistan. The study shows that EB irradiation not only enhances the color but can also improves the clarity of some type of gemstones. The treated stones included kunzite, tourmaline, topaz, quartz, aquamarine and cultured pearls. Doses ranging from 25 kGy to 200 KGy were employed to assess the influence of doses on color and clarity and to select the optimum doses. The samples used included both the natural and the faceted gemstones. It is concluded that significant revenue generation is associated with the enhancement of the color in clarity of gemstones which are available at very cheap price in the world market.

  4. Electron beam irradiation of gemstone for color enhancement

    Science.gov (United States)

    Idris, Sarada; Ghazali, Zulkafli; Hashim, Siti A'iasah; Ahmad, Shamshad; Jusoh, Mohd Suhaimi

    2012-09-01

    Numerous treatment of gemstones has been going on for hundreds of years for enhancing color and clarity of gems devoid of these attributes. Whereas previous practices included fraudulent or otherwise processes to achieve the color enhancement, the ionizing radiation has proven to be a reliable and reproducible technique. Three types of irradiation processes include exposure to gamma radiation, electron beam irradiation and the nuclear power plants. Electron Beam Irradiation of Gemstone is a technique in which a gemstone is exposed to highly ionizing radiation electron beam to knock off electrons to generate color centers culminating in introduction of deeper colors. The color centers may be stable or unstable. Below 9MeV, normally no radioactivity is introduced in the exposed gems. A study was conducted at Electron Beam Irradiation Centre (Alurtron) for gemstone color enhancement by using different kind of precious gemstones obtained from Pakistan. The study shows that EB irradiation not only enhances the color but can also improves the clarity of some type of gemstones. The treated stones included kunzite, tourmaline, topaz, quartz, aquamarine and cultured pearls. Doses ranging from 25 kGy to 200 KGy were employed to assess the influence of doses on color and clarity and to select the optimum doses. The samples used included both the natural and the faceted gemstones. It is concluded that significant revenue generation is associated with the enhancement of the color in clarity of gemstones which are available at very cheap price in the world market.

  5. Detection of DNA damage induced by heavy ion irradiation in the individual cells with comet assay

    Science.gov (United States)

    Wada, S.; Natsuhori, M.; Ito, N.; Funayama, T.; Kobayashi, Y.

    2003-05-01

    Investigating the biological effects of high-LET heavy ion irradiation at low fluence is important to evaluate the risk of charged particles. Especially it is important to detect radiation damage induced by the precise number of heavy ions in the individual cells. Thus we studied the relationship between the number of ions traversing the cell and DNA damage produced by the ion irradiation. We applied comet assay to measure the DNA damage in the individual cells. Cells attached on the ion track detector CR-39 were irradiated with ion beams at TIARA, JAERI-Takasaki. After irradiation, the cells were stained with ethidium bromide and the opposite side of the CR-39 was etched. We observed that the heavy ions with higher LET values induced the heavier DNA damage. The result indicated that the amount of DNA damage induced by one particle increased with the LET values of the heavy ions.

  6. Damage creation in porous silicon irradiated by swift heavy ions

    Energy Technology Data Exchange (ETDEWEB)

    Canut, B., E-mail: bruno.canut@insa-lyon.fr [Université de Lyon, Institut des Nanotechnologies de Lyon INL-IMR5270, CNRS, INSA de Lyon, Villeurbanne, F-69621 Villeurbanne (France); Massoud, M. [Université de Lyon, Institut des Nanotechnologies de Lyon INL-IMR5270, CNRS, INSA de Lyon, Villeurbanne, F-69621 Villeurbanne (France); Newby, P. [Centre de Recherche en Nanofabrication et Nanocaractérisation (CNR2), Université de Sherbrooke, Sherbrooke, Québec (Canada); Lysenko, V. [Université de Lyon, Institut des Nanotechnologies de Lyon INL-IMR5270, CNRS, INSA de Lyon, Villeurbanne, F-69621 Villeurbanne (France); Frechette, L. [Centre de Recherche en Nanofabrication et Nanocaractérisation (CNR2), Université de Sherbrooke, Sherbrooke, Québec (Canada); Bluet, J.M. [Université de Lyon, Institut des Nanotechnologies de Lyon INL-IMR5270, CNRS, INSA de Lyon, Villeurbanne, F-69621 Villeurbanne (France); Monnet, I. [Centre de Recherche sur les Ions, les Matériaux et la Photonique CIMAP-CIRIL, CEA–CNRS–ENSICAEN-Université de Caen, BP 5133 14070 Caen Cedex 5 (France)

    2014-05-01

    Mesoporous silicon (PS) samples were processed by anodising p{sup +} Si wafers in (1:1) HF–ethanol solution. Different current densities were used to obtain three different porosities (41%, 56% and 75%). In all cases the morphology of the PS layer is columnar with a mean crystallite size between 12 nm (75% porosity) and 19 nm (41% porosity). These targets were irradiated at the GANIL accelerator, using different projectiles ({sup 130}Xe ions of 91 MeV and 29 MeV, {sup 238}U ions of 110 MeV and 850 MeV) in order to vary the incident electronic stopping power S{sub e}. The fluences ranged between 10{sup 11} and 7 × 10{sup 13} cm{sup −2}. Raman spectroscopy and cross sectional SEM observations evidenced damage creation in the irradiated nanocrystallites, without any degradation of the PS layer morphology at fluences below 3 × 10{sup 12} cm{sup −2}. For higher doses, the columnar morphology transforms into a spongy-like structure. The damage cross sections, extracted from Raman results, increase with the electronic stopping power and with the sample porosity. At the highest S{sub e} (>10 keV nm{sup −1}) and the highest porosity (75%), the track diameter coincides with the crystallite diameter, indicating that a single projectile impact induces the crystallite amorphization along the major part of the ion path. These results were interpreted in the framework of the thermal spike model, taking into account the low thermal conductivity of the PS samples in comparison with that of bulk silicon.

  7. Resonant Raman spectroscopy study of swift heavy ion irradiated MoS2

    Science.gov (United States)

    Guo, Hang; Sun, Youmei; Zhai, Pengfei; Zeng, Jian; Zhang, Shengxia; Hu, Peipei; Yao, Huijun; Duan, Jinglai; Hou, Mingdong; Liu, Jie

    2016-08-01

    Molybdenum disulphide (MoS2) crystal samples were irradiated by swift heavy ions (209Bi and 56Fe). Hillock-like latent tracks were observed on the surface of irradiated MoS2 by atomic force microscopy. The modifications of properties of irradiated MoS2 were investigated by resonant Raman spectroscopy and ultraviolet-visible spectroscopy (UV-Vis). A new peak (E1u2, ∼385.7 cm-1) occurs near the in-plane E2g1 peak (∼383.7 cm-1) after irradiation. The two peaks shift towards lower frequency and broaden due to structural defects and stress with increasing fluence. When irradiated with high fluence, two other new peaks appear at ∼ 190 and ∼ 230 cm-1. The peak at ∼230 cm-1 is disorder-induced LA(M) mode. The presence of this mode indicates defects induced by irradiation. The feature at ∼460 cm-1 is composed of 2LA(M) (∼458 cm-1) and A2u (∼466 cm-1) mode. With increasing fluence, the integrated intensity ratio between 2LA(M) and A2u increases. The relative enhancement of 2LA(M) mode is in agreement with the appearance of LA(M) mode, which both demonstrate structural disorder in irradiated MoS2. The ∼423-cm-1 peak shifts toward lower frequency due to the decrease in exciton energy of MoS2, and this was demonstrated by the results of UV-Vis spectra. The decrease in exciton energy could be due to introduction of defect levels into band gap.

  8. Gamma-irradiation enhances transgene expression in leukemic cells.

    Science.gov (United States)

    Vereecque, R; Saudemont, A; Wickham, T J; Gonzalez, R; Hetuin, D; Fenaux, P; Quesnel, B

    2003-02-01

    The majority of immunotherapy-based gene therapy protocols consist of ex vivo gene transfer in tumor cells. To prevent further in vivo growth, modified cells must be irradiated before reinjection into patients. The present study examines the effects of gamma-irradiation on transgene expression in transduced leukemic cells. Human and murine leukemic cells were transfected with retroviral vectors or plasmids carrying beta-galactosidase, GM-CSF or CD80 genes. Fresh leukemic cells from patients with acute myeloid leukemia (AML) were transfected with AdZ.F(pK7) adenoviral vector. gamma-irradiation at various lethal doses enhanced transgene expression in leukemic cell lines and fresh AML cells when the gene of interest was under CMV promoter but not when SV40 promoter was used. Oxidative stress also enhanced transgene expression and both irradiation and oxidative stress effects were inhibited by addition of N-acetyl-L-cysteine, a thiol anti-oxidant, indicating the involvement of reactive oxygen species. Transgene expression was also enhanced in vivo 48 and 120 h after subcutaneous injection of irradiated leukemic cells in syngeneic mice. These results show that a cell vaccine protocol using ex vivo gene transfer of transduced cells might be feasible in acute leukemia even if leukemic cells must be irradiated at lethal doses prior to reinjection to patients.

  9. Reliability studies on NPN RF power transistors under swift heavy ion irradiation

    Science.gov (United States)

    Pushpa, N.; Praveen, K. C.; Gnana Prakash, A. P.; Naik, P. S.; Cressler, John D.; Gupta, S. K.; Revannasiddaiah, D.

    2012-02-01

    NPN RF power transistors were irradiated with 140 MeV Si 10+ ions, 100 MeV F 8+ ions, 50 MeV Li 3+ ions and Co-60 gamma radiation in the dose range from 100 krad to 100 Mrad. The transistor characteristics are studied before and after irradiation from which the parameters such as Gummel characteristics, excess base current (Δ IB = IBpost - IBpre), dc current gain ( hFE), transconductance ( gm) and collector-saturation current ( ICSat) are determined. The degradation observed in the electrical characteristics is almost the same for different types of ion irradiated NPN RF power transistors with similar total doses although there is a large difference in the linear energy transfer (LET) of the ions. Further, it was observed more degradation in DC I- V characteristics of ion irradiated devices than the Co-60 gamma irradiated devices for higher doses.

  10. Modulation of electrical mobility in Au ion irradiated titanium oxide with crystal field splitting

    Science.gov (United States)

    Park, Hyun-Woo; Jun, Byung-Hyuk; Choi, Dukhyun; Chung, Kwun-Bum

    2016-11-01

    Electrical modulation of radio frequency (RF) sputtered TiO2- x films were investigated as a function of Au swift heavy ion irradiation dose at room temperature. The prepared TiO2- x films were irradiated with 130 MeV Au swift heavy ion in the range from 1 × 1011 to 5 × 1012 ions/cm2. As the Au ion irradiation dose increased up to 1 × 1012 ions/cm2, the electrical mobility of TiO2- x films were dramatically increased 3.07 × 102 cm2 V-1 s-1 without the change of carrier concentration. These changes in electrical properties of Au irradiated TiO2- x film, are related to the modification of electronic structure such as crystal field splitting of Ti 3d orbital hybridization and sub-band edge states below the conduction band as a function of Au swift heavy ion irradiation dose.

  11. Respiratory gated irradiation system for heavy-ion radiotherapy.

    Science.gov (United States)

    Minohara, S; Kanai, T; Endo, M; Noda, K; Kanazawa, M

    2000-07-01

    In order to reduce the treatment margin of the moving target due to breathing, we developed a gated irradiation system for heavy-ion radiotherapy. The motion of a patient due to respiration is detected by the motion of the body surface around the chest wall. A respiratory sensor was developed using an infrared light spot and a position-sensitive detector. A timing signal to request a beam is generated in response to the respiration waveform, and a carbon beam is extracted from the synchrotron using a RF-knockout method. CT images for treatment planning are taken in synchronization with the respiratory motion. For patient positioning, digitized fluoroscopic images superimposed with the respiration waveform were used. The relation between the respiratory sensor signal and the organ motion was examined using digitized video images from fluoroscopy. The performance of our gated system was demonstrated by using the moving phantom, and dose profiles were measured in the direction of phantom motion. The timing of gate-on is set at the end of the expiratory phase, because the motion of the diaphragm is slower and more reproducible than during the inspiratory phase. The signal of the respiratory sensor shows a phase difference of 120 milliseconds between lower and upper locations on the chest wall. The motion of diaphragm is delayed by 200 milliseconds from the respiration waveform at the lower location. The beam extraction system worked according to the beam on/off logic for gating, and the gated CT scanner performed well. The lateral penumbra size of the dose profile along the moving axis was distinguishably decreased by the gated irradiation. The ratio of the nongated to gated lateral fall-off was 4.3, 3.5, and 2. 0 under the stroke of 40.0, 29.0, and 13.0 mm respectively. We developed a total treatment system of gated irradiation for heavy-ion radiotherapy. We found that with this system the target margin along the body axis could be decreased to 5-10 mm although the

  12. Nb2O5 Nanostructure Evolution on Nb Surfaces via Low-Energy He(+) Ion Irradiation.

    Science.gov (United States)

    Novakowski, Theodore Joseph; Tripathi, Jitendra Kumar; Hassanein, Ahmed

    2016-12-21

    We propose low-energy, broad-beam He(+) ion irradiation as a novel processing technique for the generation of Nb2O5 surface nanostructures due to its relative simplicity and scalability in a commercial setting. Since there have been relatively few studies involving the interaction of high-fluence, low-energy He(+) ion irradiation and Nb (or its oxidized states), this systematic study explores both effects of fluence and sample temperature during irradiation on resulting surface morphology. Detailed normal and cross-sectional scanning electron microscopy (SEM) studies reveal subsurface He bubble formation and elucidate potential driving mechanisms for nanostructure evolution. A combination of specular optical reflectivity and X-ray photoelectron spectroscopy (XPS) is also used to gain additional information on roughness and stoichiometry of irradiated surfaces. Our investigations show significant surface modification for all tested irradiation conditions; the resulting surface structure size and geometry have a strong dependence on both sample temperature during irradiation and total ion fluence. Optical reflectivity measurements on irradiated surfaces demonstrate increased surface roughening with increasing ion fluence, and XPS shows higher oxidation levels for samples irradiated at lower temperatures, suggesting larger surface roughness and porosity. Overall, it was found that low-energy He(+) ion irradiation is an efficient processing technique for nanostructure formation, and surface structures are highly tunable by adjusting ion fluence and Nb2O5 sample temperature during irradiation. These findings may have excellent potential applications for solar energy conversion through improved efficiency due to effective light absorption.

  13. Instrumentation to Enhance Advanced Test Reactor Irradiations

    Energy Technology Data Exchange (ETDEWEB)

    J. L. Rempe; D. L. Knudson; K. G. Condie; J. E. Daw; S. C. Taylor

    2009-09-01

    The Department of Energy (DOE) designated the Advanced Test Reactor (ATR) as a National Scientific User Facility (NSUF) in April 2007 to support U.S. leadership in nuclear science and technology. By attracting new research users - universities, laboratories, and industry - the ATR will support basic and applied nuclear research and development, further advancing the nation's energy security needs. A key component of the ATR NSUF effort is to prove new in-pile instrumentation techniques that are capable of providing real-time measurements of key parameters during irradiation. To address this need, an assessment of instrumentation available and under-development at other test reactors has been completed. Based on this review, recommendations are made with respect to what instrumentation is needed at the ATR and a strategy has been developed for obtaining these sensors. Progress toward implementing this strategy is reported in this document. It is anticipated that this report will be updated on an annual basis.

  14. Heavy ion irradiation effects of polymer film on absorption of light

    Energy Technology Data Exchange (ETDEWEB)

    Kasai, Noboru; Seguchi, Tadao [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment; Arakawa, Tetsuhito

    1997-03-01

    Ion irradiation effects on the absorption of light for three types of polymer films; polyethylene-terephthalate (PET), polyethylene-naphthalate (PEN), and polyether-ether-ketone (PEEK) were investigated by irradiation of heavy ions with Ni{sup 4+}(15MeV), O{sup 6+}(160MeV), and Ar{sup 8+}(175MeV), and compared with electron beams(EB) irradiation. The change of absorption at 400nm by a photometer was almost proportional to total dose for ions and EB. The absorption per absorbed dose was much high in Ni{sup 4+}, but rather small in O{sup 6+} and Ar{sup 8+} irradiation, and the absorption by EB irradiation was accelerated by the temperature of polymer film during irradiation. The beam heating of materials during ion irradiation was assumed, especially for Ni ion irradiation. The heavy ion irradiation effect of polymers was thought to be much affected by the ion beam heating than the linear energy transfer(LET) of radiation source. (author)

  15. In-situ TEM ion irradiation investigations on U3Si2 at LWR temperatures

    Science.gov (United States)

    Miao, Yinbin; Harp, Jason; Mo, Kun; Bhattacharya, Sumit; Baldo, Peter; Yacout, Abdellatif M.

    2017-02-01

    The radiation-induced amorphization of U3Si2 was investigated by in-situ transmission electron microscopy using 1 MeV Kr ion irradiation. Both arc-melted and sintered U3Si2 specimens were irradiated at room temperature to confirm the similarity in their responses to radiation. The sintered specimens were then irradiated at 350 °C and 550 °C up to 7.2 × 1015 ions/cm2 to examine their amorphization behavior under light water reactor (LWR) conditions. U3Si2 remains crystalline under irradiation at LWR temperatures. Oxidation of the material was observed at high irradiation doses.

  16. Ion formation in laser-irradiated cesium vapor

    Energy Technology Data Exchange (ETDEWEB)

    Mahmoud, M.A. [National Institute of Laser Enhanced Science, Cairo University, Cairo (Egypt)]. E-mail: Hameid56@hotmail.com; Gamal, Y.E.E. [Physics Department, Faculty of Science, South Valley University, Sohag (Egypt); Abd El-Rahman, H.A. [National Institute of Laser Enhanced Science, Cairo University, Cairo (Egypt)

    2006-11-15

    We study theoretically the formation of Cs{sup +} and Cs{sub 2}{sup +} during cw laser radiation resonant with 6s-7p transition of Cs atomic vapor. This is done by numerically solving rate equations for the evolution of atomic state and electron populations. The results of calculations for the atomic and molecular ions density at different values of laser power clarified that the associative ionization and Penning ionization process play an important role for producing the Cs{sub 2}{sup +} and Cs{sup +}, respectively, during the plasma formation. Also, the results showed that laser power of the order of 150mW and 40-50ns irradiation time are optimal in producing a fully ionized plasma.

  17. Diamond single crystal-surface modification under high- fluence ion irradiation

    Science.gov (United States)

    Anikin, V. A.; Borisov, A. M.; Kazakov, V. A.; Mashkova, E. S.; Palyanov, Yu N.; Popov, V. P.; Shmytkova, E. A.; Sigalaev, S. K.

    2016-09-01

    The modification of (111) face of synthetic diamond has been studied experimentally for high-fluence 30 keV argon bombardment. It has been found that ion irradiation leads to the electrically conductive layer formation the sheet resistance of which decreases more than 100 times while changing the temperature of the irradiated diamond from 70 to 400 oC. This effect, as well as significant changes of optical transmittance after ion irradiation are associated with ion-induced structural changes of irradiated diamond obtained by the methods of Raman spectroscopy.

  18. Damage accumulation in MgO irradiated with MeV Au ions at elevated temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Bachiller-Perea, Diana, E-mail: dianabachillerperea@gmail.com [Centre de Sciences Nucléaires et de Sciences de la Matière (CSNSM), Univ. Paris-Sud, CNRS-IN2P3, Université Paris-Saclay, 91405, Orsay Cedex (France); Centro de Micro-Análisis de Materiales, Universidad Autónoma de Madrid, C/Faraday 3, 28049, Madrid (Spain); Dpto. de Física Aplicada, Universidad Autónoma de Madrid, Ciudad Universitaria de Cantoblanco, 28049, Madrid (Spain); Debelle, Aurélien, E-mail: aurelien.debelle@u-psud.fr [Centre de Sciences Nucléaires et de Sciences de la Matière (CSNSM), Univ. Paris-Sud, CNRS-IN2P3, Université Paris-Saclay, 91405, Orsay Cedex (France); Thomé, Lionel [Centre de Sciences Nucléaires et de Sciences de la Matière (CSNSM), Univ. Paris-Sud, CNRS-IN2P3, Université Paris-Saclay, 91405, Orsay Cedex (France); Behar, Moni [Instituto de Física, Universidade Federal do Rio Grande do Sul, C.P. 15051, 91501-970, Porto Alegre, RS (Brazil)

    2016-09-15

    The damage accumulation process in MgO single crystals under medium-energy heavy ion irradiation (1.2 MeV Au) at fluences up to 4 × 10{sup 14} cm{sup −2} has been studied at three different temperatures: 573, 773, and 1073 K. Disorder depth profiles have been determined through the use of the Rutherford backscattering spectrometry in channeling configuration (RBS/C). The analysis of the RBS/C data reveals two steps in the MgO damage process, irrespective of the temperature. However, we find that for increasing irradiation temperature, the damage level decreases and the fluence at which the second step takes place increases. A shift of the damage peak at increasing fluence is observed for the three temperatures, although the position of the peak depends on the temperature. These results can be explained by an enhanced defect mobility which facilitates defect migration and may favor defect annealing. X-ray diffraction reciprocal space maps confirm the results obtained with the RBS/C technique. - Highlights: • High-temperature MeV-ion irradiated MgO exhibits a two-step damage process. • The occurrence of the second step is delayed with increasing temperature. • The damage level decreases with increasing temperature. • A shift of the damage peak is observed with increasing fluence. • A high defect mobility at high temperatures in MgO is clearly evidenced.

  19. Oxide dispersion strengthened steel irradiation with helium ions

    Energy Technology Data Exchange (ETDEWEB)

    Pouchon, M.A. [Laboratory for Materials Behaviour, Paul Scherrer Institute, OHLA/131, 5232 Villigen PSI (Switzerland)]. E-mail: manuel.pouchon@psi.ch; Chen, J. [Laboratory for Materials Behaviour, Paul Scherrer Institute, OHLA/131, 5232 Villigen PSI (Switzerland); Doebeli, M. [Laboratory for Materials Behaviour, Paul Scherrer Institute, OHLA/131, 5232 Villigen PSI (Switzerland); Hoffelner, W. [Laboratory for Materials Behaviour, Paul Scherrer Institute, OHLA/131, 5232 Villigen PSI (Switzerland)

    2006-06-30

    Oxide dispersion strengthened (ODS) ferritic steels are investigated as possible structural material for the future generation of high temperature gas cooled nuclear reactors. ODS-steels are considered to replace other high temperature materials for tubing or structural parts. The oxide particles serve for interfacial pinning of moving dislocations. Therefore, the creep resistance is improved. In case of the usage of these materials in reactors, the behavior under irradiation must be further clarified. In this paper the effects induced by {sup 4}He{sup 2+} implantation into a ferritic ODS steel are investigated. The fluence ranges from 10{sup 16} to 10{sup 17} cm{sup -2} and the energy from 1 to 2 MeV. The induced swelling is investigated for implantations at room temperature and 470 K. It is derived from the irradiation induced surface displacement, which is measured with an atomic force microscope (AFM). With a displacement damage of 0.6 dpa, a volume increase of 0.65% is observed at room temperature and 0.33% at 470 K. A cross-sectional cut is performed by focused ion beam and investigated by transmission electron microcopy (TEM). The defect density observed on the TEM micrographs agrees well with the computational simulation (TRIM) of the damage profile.

  20. Enhancing the performances of ECR Ion Sources

    Energy Technology Data Exchange (ETDEWEB)

    Alton, G.D.; Liu, Y.

    1999-03-29

    The performances of ECR ion sources can be enhanced in the spatial domain by tailoring the central magnetic field so that it is uniformly distributed over a large plasma volume and is of magnitude so as to be in resonance with single frequency microwave radiation. Analogously, the performances of conventional minimum-B ECR ion sources can be enhanced in the frequency domain by injecting multiple discrete frequency or broadband microwave radiation into their plasma volumes. In this report, examples of both the spatial-and frequency-domain techniques will be given. For example, the design aspects of an all permanent-magnet ''volume-type'' (spatial-domain) ECR ion source will be described and the effects of injecting multiple frequencies (frequency-domain) on the charge-state-distributions extracted from a conventional minimum-B ECR ion source will be presented.

  1. Effect of 120 MeV Ag{sup 9+} ion irradiation of YCOB single crystals

    Energy Technology Data Exchange (ETDEWEB)

    Arun Kumar, R., E-mail: rarunpsgtech@yahoo.com [Crystal Growth Centre, Anna University, Chennai 600 025 (India); Department of Basic Sciences - Physics Division, PSG College of Technology, Coimbatore 641 004 (India); Dhanasekaran, R. [Crystal Growth Centre, Anna University, Chennai 600 025 (India)

    2012-09-15

    Single crystals of yttrium calcium oxy borate (YCOB) grown from boron-tri-oxide flux were subjected to swift heavy ion irradiation using silver Ag{sup 9+} ions from the 15 UD Pelletron facility at Inter University Accelerator Center, New Delhi. The crystals were irradiated at 1 Multiplication-Sign 10{sup 13}, 5 Multiplication-Sign 10{sup 13} and 1 Multiplication-Sign 10{sup 14} ions/cm{sup 2} fluences at room temperature and with 5 Multiplication-Sign 10{sup 13} ions/cm{sup 2} fluence at liquid nitrogen temperature. The pristine and the irradiated samples were characterized by glancing angle X-ray diffraction, UV-Vis-NIR and photoluminescence studies. From the characterization studies performed on the samples, it is inferred that the crystals irradiated at liquid nitrogen temperature had fewer defects compared to the crystals irradiated at room temperature and the defects increased when the ion fluence was increased at room temperature.

  2. A review of transmission electron microscopes with in situ ion irradiation

    Science.gov (United States)

    Hinks, J. A.

    2009-12-01

    Transmission electron microscopy (TEM) with in situ ion irradiation is unique amongst experimental techniques in allowing the direct observation of the internal microstructure of materials on the nanoscale whilst they are being subjected to bombardment with energetic particles. Invaluable insights into the underlying atomistic processes at work can be gained through direct investigation of radiation induced and enhanced effects such as: phase changes and segregation; mechanical and structural changes; atomic/layer mixing and chemical disorder; compositional changes; chemical reactions; grain growth and shrinkage; precipitation and dissolution; defect/bubble formation, growth, motion, coalescence, removal and destruction; ionisation; diffusion; and collision cascades. The experimental results obtained can be used to validate the predictions of computational models which in turn can elucidate the mechanisms behind the phenomena seen in the microscope. It is 50 years since the first TEM observations of in situ ion irradiation were made by D.W. Pashley, A.E.B. Presland and J.W. Menter at the Tube Investment Laboratories in Cambridge, United Kingdom and 40 years since the first interfacing of an ion beam system with a TEM by P.A. Thackery, R.S. Nelson and H.C. Sansom at the Atomic Energy Research Establishment at Harwell, United Kingdom. In that time the field has grown with references in the literature to around thirty examples of such facilities. This paper gives an overview of the importance of the technique, especially with regard to the current challenges faced in understanding radiation damage in nuclear environments; a description of some of the important construction elements and design considerations of TEMs with in situ ion irradiation; a brief history of the development of this type of instrument; a summary of the facilities built around the world over the last half century; and finally a focus on the instruments in operation today.

  3. A review of transmission electron microscopes with in situ ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Hinks, J.A., E-mail: j.a.hinks@salford.ac.u [Centre for Functional Materials, University of Salford, Salford M5 4WT (United Kingdom)

    2009-12-15

    Transmission electron microscopy (TEM) with in situ ion irradiation is unique amongst experimental techniques in allowing the direct observation of the internal microstructure of materials on the nanoscale whilst they are being subjected to bombardment with energetic particles. Invaluable insights into the underlying atomistic processes at work can be gained through direct investigation of radiation induced and enhanced effects such as: phase changes and segregation; mechanical and structural changes; atomic/layer mixing and chemical disorder; compositional changes; chemical reactions; grain growth and shrinkage; precipitation and dissolution; defect/bubble formation, growth, motion, coalescence, removal and destruction; ionisation; diffusion; and collision cascades. The experimental results obtained can be used to validate the predictions of computational models which in turn can elucidate the mechanisms behind the phenomena seen in the microscope. It is 50 years since the first TEM observations of in situ ion irradiation were made by D.W. Pashley, A.E.B. Presland and J.W. Menter at the Tube Investment Laboratories in Cambridge, United Kingdom and 40 years since the first interfacing of an ion beam system with a TEM by P.A. Thackery, R.S. Nelson and H.C. Sansom at the Atomic Energy Research Establishment at Harwell, United Kingdom. In that time the field has grown with references in the literature to around thirty examples of such facilities. This paper gives an overview of the importance of the technique, especially with regard to the current challenges faced in understanding radiation damage in nuclear environments; a description of some of the important construction elements and design considerations of TEMs with in situ ion irradiation; a brief history of the development of this type of instrument; a summary of the facilities built around the world over the last half century; and finally a focus on the instruments in operation today.

  4. Tuning surface porosity on vanadium surface by low energy He{sup +} ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Tripathi, J.K., E-mail: jtripat@purdue.edu; Novakowski, T.J.; Hassanein, A.

    2016-08-15

    Highlights: • Surface nanostructuring on vanadium surface using novel He{sup +} ion irradiation process. • Tuning surface-porosity using high-flux, low-energy He{sup +} ion irradiation at constant elevated sample temperature (823–173 K). • Presented top-down approach guarantees good contact between different crystallites. • Sequential significant enhancement in surface-pore edge size (and corresponding reduction in surface-pore density) with increasing sample temperature. - Abstract: In the present study, we report on tuning the surface porosity on vanadium surfaces using high-flux, low-energy He{sup +} ion irradiation as function of sample temperature. Polished, mirror-finished vanadium samples were irradiated with 100 eV He{sup +} ions at a constant ion-flux of 7.2 × 10{sup 20} ions m{sup −2} s{sup −1} for 1 h duration at constant sample temperatures in the wide range of 823–1173 K. Our results show that the surface porosity of V{sub 2}O{sub 5} (naturally oxidized vanadium porous structure, after taking out from UHV) is strongly correlated to the sample temperature and is highly tunable. In fact, the surface porosity significantly increases with reducing sample temperature and reaches up to ∼87%. Optical reflectivity on these highly porous V{sub 2}O{sub 5} surfaces show ∼0% optical reflectivity at 670 nm wavelength, which is very similar to that of “black metal”. Combined with the naturally high melting point of V{sub 2}O{sub 5}, this very low optical reflectivity suggests potential application in solar power concentration technology. Additionally, this top-down approach guarantees relatively good contact between the different crystallites and avoids electrical conductivity limitations (if required). Since V{sub 2}O{sub 5} is naturally a potential photocatalytic material, the resulting sub-micron-sized cube-shaped porous structures could be used in solar water splitting for hydrogen production in energy applications.

  5. Surface nanostructuring of TiO{sub 2} thin films by ion beam irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Romero-Gomez, P. [Instituto de Ciencia de Materiales de Sevilla, Consejo Superior de Investigaciones Cientificas, Universidad de Sevilla, c/Americo Vespucio 49, 41092 Sevilla (Spain); Palmero, A. [Instituto de Ciencia de Materiales de Sevilla, Consejo Superior de Investigaciones Cientificas, Universidad de Sevilla, c/Americo Vespucio 49, 41092 Sevilla (Spain)], E-mail: alberto.palmero@icmse.csic.es; Yubero, F. [Instituto de Ciencia de Materiales de Sevilla, Consejo Superior de Investigaciones Cientificas, Universidad de Sevilla, c/Americo Vespucio 49, 41092 Sevilla (Spain); Vinnichenko, M.; Kolitsch, A. [Institute of Ion Beam Physics and Materials Research, Forschungszentrum Dresden-Rossendorf, POB 510119, 01314 Dresden (Germany); Gonzalez-Elipe, A.R. [Instituto de Ciencia de Materiales de Sevilla, Consejo Superior de Investigaciones Cientificas, Universidad de Sevilla, c/Americo Vespucio 49, 41092 Sevilla (Spain)

    2009-04-15

    This work reports a procedure to modify the surface nanostructure of TiO{sub 2} anatase thin films through ion beam irradiation with energies in the keV range. Irradiation with N{sup +} ions leads to the formation of a layer with voids at a depth similar to the ion-projected range. By setting the ion-projected range a few tens of nanometers below the surface of the film, well-ordered nanorods appear aligned with the angle of incidence of the ion beam. Slightly different results were obtained by using heavier (S{sup +}) and lighter (B{sup +}) ions under similar conditions.

  6. Characterization of ion track morphology formed by swift heavy ion irradiation in silicon oxynitride films

    Directory of Open Access Journals (Sweden)

    Mota–Santiago P.

    2015-01-01

    Full Text Available Amorphous silicon oxynitride (SiOxNy possess interesting optical and mechanical properties. Here, we present direct evidence for the formation of ion tracks in 1 µm thick silicon oxynitride of different stoichiometries. The tracks were created by irradiation with 185 MeV Au13+ ions. The samples were studied using spectral reflectometry and Rutherford backscattering spectrometry (RBS, with the track morphology characterised by means of small angle X–ray scattering (SAXS. The radial density of the ion tracks resembles a core–shell structure with a typical radius of ~ 1.8 + 2.4 nm in the case of Si3N4 and 2.3 + 3.2 nm for SiO2.

  7. Secondary particle tracks generated by ion beam irradiation

    Science.gov (United States)

    García, Gustavo

    2015-05-01

    The Low Energy Particle Track Simulation (LEPTS) procedure is a powerful complementary tool to include the effect of low energy electrons and positrons in medical applications of radiation. In particular, for ion-beam cancer treatments provides a detailed description of the role of the secondary electrons abundantly generated around the Bragg peak as well as the possibility of using transmuted positron emitters (C11, O15) as a complement for ion-beam dosimetry. In this study we present interaction probability data derived from IAM-SCAR corrective factors for liquid environments. Using these data, single electron and positron tracks in liquid water and pyrimidine have been simulated providing information about energy deposition as well as the number and type of interactions taking place in any selected ``nanovolume'' of the irradiated area. In collaboration with Francisco Blanco, Universidad Complutense de Madrid; Antonio Mu noz, Centro de Investigaciones Energéticas Medioambientales y Tecnológicas and Diogo Almeida, Filipe Ferreira da Silva, Paulo Lim ao-Vieira, Universidade Nova de Lisboa. Supported by the Spanish and Portuguese governments.

  8. Atomistic-Scale Simulations of Defect Formation in Graphene under Noble Gas Ion Irradiation.

    Science.gov (United States)

    Yoon, Kichul; Rahnamoun, Ali; Swett, Jacob L; Iberi, Vighter; Cullen, David A; Vlassiouk, Ivan V; Belianinov, Alex; Jesse, Stephen; Sang, Xiahan; Ovchinnikova, Olga S; Rondinone, Adam J; Unocic, Raymond R; van Duin, Adri C T

    2016-09-27

    Despite the frequent use of noble gas ion irradiation of graphene, the atomistic-scale details, including the effects of dose, energy, and ion bombardment species on defect formation, and the associated dynamic processes involved in the irradiations and subsequent relaxation have not yet been thoroughly studied. Here, we simulated the irradiation of graphene with noble gas ions and the subsequent effects of annealing. Lattice defects, including nanopores, were generated after the annealing of the irradiated graphene, which was the result of structural relaxation that allowed the vacancy-type defects to coalesce into a larger defect. Larger nanopores were generated by irradiation with a series of heavier noble gas ions, due to a larger collision cross section that led to more detrimental effects in the graphene, and by a higher ion dose that increased the chance of displacing the carbon atoms from graphene. Overall trends in the evolution of defects with respect to a dose, as well as the defect characteristics, were in good agreement with experimental results. Additionally, the statistics in the defect types generated by different irradiating ions suggested that the most frequently observed defect types were Stone-Thrower-Wales (STW) defects for He(+) irradiation and monovacancy (MV) defects for all other ion irradiations.

  9. Ion beam irradiation as a tool to improve the ionic conductivity in solid polymer electrolyte systems

    Energy Technology Data Exchange (ETDEWEB)

    Manjunatha, H., E-mail: h-manjunath@blr.amrita.edu; Kumaraswamy, G. N. [Department of Physics, Amrita Vishwa Vidyapeetham, Bengaluru-560 035 (India); Damle, R. [Department of Physics, Bangalore University, Bengaluru-560 056 (India)

    2016-05-06

    Solid polymer electrolytes (SPEs) have potential applications in solid state electronic and energy devices. The optimum conductivity of SPEs required for such applications is about 10{sup −1} – 10{sup −3} Scm{sup −1}, which is hard to achieve in these systems. It is observed that ionic conductivity of SPEs continuously increase with increasing concentration of inorganic salt in the host polymer. However, there is a critical concentration of the salt beyond which the conductivity of SPEs decreases due to the formation of ion pairs. In the present study, solid polymer thin films based on poly (ethylene oxide) (PEO) complexed with NaBr salt with different concentrations have been prepared and the concentration at which ion pair formation occurs in PEO{sub x}NaBr is identified. The microstructure of the SPE with highest ionic conductivity is modified by irradiating it with low energy O{sup +1} ion (100 keV) of different fluencies. It is observed that the ionic conductivity of irradiated SPEs increases by one order in magnitude. The increase in ionic conductivity may be attributed to the enhanced segmental motion of the polymer chains due to radiation induced micro structural modification.

  10. Ion beam irradiation as a tool to improve the ionic conductivity in solid polymer electrolyte systems

    Science.gov (United States)

    Manjunatha, H.; Damle, R.; Kumaraswamy, G. N.

    2016-05-01

    Solid polymer electrolytes (SPEs) have potential applications in solid state electronic and energy devices. The optimum conductivity of SPEs required for such applications is about 10-1 - 10-3 Scm-1, which is hard to achieve in these systems. It is observed that ionic conductivity of SPEs continuously increase with increasing concentration of inorganic salt in the host polymer. However, there is a critical concentration of the salt beyond which the conductivity of SPEs decreases due to the formation of ion pairs. In the present study, solid polymer thin films based on poly (ethylene oxide) (PEO) complexed with NaBr salt with different concentrations have been prepared and the concentration at which ion pair formation occurs in PEOxNaBr is identified. The microstructure of the SPE with highest ionic conductivity is modified by irradiating it with low energy O+1 ion (100 keV) of different fluencies. It is observed that the ionic conductivity of irradiated SPEs increases by one order in magnitude. The increase in ionic conductivity may be attributed to the enhanced segmental motion of the polymer chains due to radiation induced micro structural modification.

  11. MeV single-ion beam irradiation of mammalian cells using the Surrey vertical nanobeam, compared with broad proton beam and X-ray irradiations

    Energy Technology Data Exchange (ETDEWEB)

    Prakrajang, K. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Faculty of Science, Maejo University, Chiang Mai 50290 (Thailand); Jeynes, J.C.G.; Merchant, M.J.; Kirkby, K.; Kirkby, N. [Surrey Ion Beam Center, Faculty of Engineering and Physical Science, University of Surrey, Guildford Surrey, GU2 7XH (United Kingdom); Thopan, P. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Yu, L.D., E-mail: yuld@fnrf.science.cmu.ac.th [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Thailand Center of Excellence in Physics, Commission on Higher Education, 328 Si Ayutthaya Road, Bangkok 10400 (Thailand)

    2013-07-15

    Highlights: •Recently completed nanobeam at the Surrey Ion Beam Centre was used. •3.8-MeV single and broad proton beams irradiated Chinese hamster cells. •Cell survival curves were measured and compared with 300-kV X-ray irradiation. •Single ion irradiation had a lower survival part at ultra-low dose. •It implies hypersensitivity, bystander effect and cell cycle phase of cell death. -- Abstract: As a part of a systematic study on mechanisms involved in physical cancer therapies, this work investigated response of mammalian cells to ultra-low-dose ion beam irradiation. The ion beam irradiation was performed using the recently completed nanobeam facility at the Surrey Ion Beam Centre. A scanning focused vertical ion nano-beam was applied to irradiate Chinese hamster V79 cells. The V79 cells were irradiated in two different beam modes, namely, focused single ion beam and defocused scanning broad ion beam of 3.8-MeV protons. The single ion beam was capable of irradiating a single cell with a precisely controlled number of the ions to extremely low doses. After irradiation and cell incubation, the number of surviving colonies as a function of the number of the irradiating ions was measured for the cell survival fraction curve. A lower survival for the single ion beam irradiation than that of the broad beam case implied the hypersensitivity and bystander effect. The ion-beam-induced cell survival curves were compared with that from 300-kV X-ray irradiation. Theoretical studies indicated that the cell death in single ion irradiation mainly occurred in the cell cycle phases of cell division and intervals between the cell division and the DNA replication. The success in the experiment demonstrated the Surrey vertical nanobeam successfully completed.

  12. Development of heavy-ion irradiation technique for single-event in semiconductor devices

    Energy Technology Data Exchange (ETDEWEB)

    Nemoto, Norio; Akutsu, Takao; Matsuda, Sumio [National Space Development Agency of Japan, Tsukuba, Ibaraki (Japan). Tsukuba Space Center; Naitoh, Ichiro; Itoh, Hisayoshi; Agematsu, Takashi; Kamiya, Tomihiro; Nashiyama, Isamu

    1997-03-01

    Heavy-ion irradiation technique has been developed for the evaluation of single-event effects on semiconductor devices. For the uniform irradiation of high energy heavy ions to device samples, we have designed and installed a magnetic beam-scanning system in a JAERI cyclotron beam course. It was found that scanned area was approximately 4 x 2 centimeters and that the deviation of ion fluence from the average value was less than 7%. (author)

  13. Temperature dependent surface modification of molybdenum due to low energy He{sup +} ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Tripathi, J.K., E-mail: jtripat@purdue.edu [Center for Materials Under Extreme Environment (CMUXE), School of Nuclear Engineering, Purdue University, West Lafayette, IN 47907 (United States); Novakowski, T.J.; Joseph, G. [Center for Materials Under Extreme Environment (CMUXE), School of Nuclear Engineering, Purdue University, West Lafayette, IN 47907 (United States); Linke, J. [Forschungszentrum Jülich GmbH, EURATOM Association, Jülich D-52425 (Germany); Hassanein, A. [Center for Materials Under Extreme Environment (CMUXE), School of Nuclear Engineering, Purdue University, West Lafayette, IN 47907 (United States)

    2015-09-15

    In this paper, we report on the temperature dependent surface modifications in molybdenum (Mo) samples due to 100 eV He{sup +} ion irradiation in extreme conditions as a potential candidate to plasma-facing components in fusion devices alternative to tungsten. The Mo samples were irradiated at normal incidence, using an ion fluence of 2.6 × 10{sup 24} ions m{sup −2} (with a flux of 7.2 × 10{sup 20} ions m{sup −2} s{sup −1}). Surface modifications have been studied using high-resolution field emission scanning electron-(SEM) and atomic force (AFM) microscopy. At 773 K target temperature homogeneous evolution of molybdenum nanograins on the entire Mo surface were observed. However, at 823 K target temperature appearance of nano-pores and pin-holes nearby the grain boundaries, and Mo fuzz in patches were observed. The fuzz density increases significantly with target temperatures and continued until 973 K. However, at target temperatures beyond 973 K, counterintuitively, a sequential reduction in the fuzz density has been seen till 1073 K temperatures. At 1173 K and above temperatures, only molybdenum nano structures were observed. Our temperature dependent studies confirm a clear temperature widow, 823–1073 K, for Mo fuzz formation. Ex-situ high resolution X-ray photoelectron spectroscopy studies on Mo fuzzy samples show the evidence of MoO{sub 3} 3d doublets. This elucidates that almost all the Mo fuzz were oxidized during open air exposure and are thick enough as well. Likewise the microscopy studies, the optical reflectivity measurements also show a sequential reduction in the reflectivity values (i.e., enhancement in the fuzz density) up to 973 K and after then a sequential enhancement in the reflectivity values (i.e., reduction in the fuzz density) with target temperatures. This is in well agreement with microscopy studies where we observed clear temperature window for Mo fuzz growth.

  14. Fast luminescence in vacuum ultraviolet region in heavy-ion-irradiated α-Al{sub 2}O{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Koshimizu, Masanori, E-mail: koshi@qpc.che.tohoku.ac.jp [Department of Applied Chemistry, Graduate School of Engineering, Tohoku University, 6-6-07 Aoba, Aramaki, Aoba-ku, Sendai 980-8579 (Japan); Kimura, Kazuie [RIKEN, 2-1 Hirosawa, Wako-shi, Saitama 351-0198 (Japan); Fujimoto, Yutaka; Asai, Keisuke [Department of Applied Chemistry, Graduate School of Engineering, Tohoku University, 6-6-07 Aoba, Aramaki, Aoba-ku, Sendai 980-8579 (Japan)

    2015-12-15

    We analyzed the time-resolved luminescence properties of α-Al{sub 2}O{sub 3} under heavy ion irradiations in the vacuum ultraviolet (VUV) wavelength region. A luminescence band at approximately 170 nm, at which a luminescence band was observed under VUV irradiation and was ascribed to self-shrunk excitons. The decay rate increased with the linear energy transfer (LET). The luminescence efficiency of the band increased sharply with the LET for the case of Xe irradiation, whose LET was estimated to be higher than the threshold LET for track formation. The fast decay rate and high luminescence intensity for Xe irradiation was explained according to the enhanced radiative rate caused by close interactions among excited states.

  15. Enhanced Li-Ion Battery

    Directory of Open Access Journals (Sweden)

    Natasha Ross

    2015-01-01

    Full Text Available Au with Pd nanoparticles were synthesized and coated onto the spinel LiMn2O4 via a coprecipitation calcination method with the objective to improve the microstructure, conductivity, and electrochemical activities of pristine LiMn2O4. The novel LiPdAuxMn2-xO4 composite cathode had high phase purity, well crystallized particles, and more regular morphological structures with narrow size distributions. At enlarged cycling potential ranges the LiPdAuxMn2-xO4 sample delivered 90 mAh g−1 discharge capacity compared to LiMn2O4 (45 mAh g−1. It was concluded that even a small amount of the Pd and Au enhanced both the lithium diffusivity and electrochemical conductivity of the host sample due to the beneficial properties of their synergy.

  16. Structural damage in InGaN induced by MeV heavy ion irradiation

    Science.gov (United States)

    Zhang, L. M.; Fadanelli, R. C.; Hu, P.; Zhao, J. T.; Wang, T. S.; Zhang, C. H.

    2015-08-01

    In0.18Ga0.82N films were irradiated with 4 MeV 84Kr and 8.9 MeV 209Bi ions to various fluences at room temperature. The irradiated films were analyzed by means of Rutherford backscattering/channeling (RBS/C) and high resolution X-ray diffraction (HRXRD). The RBS/C measurements show that under the irradiation conditions, the relative lattice disorder in the films, obtained from the normalized backscattering yield, exhibits a rapid increase in the range from ∼2% to 68%. There is also an increasing lattice expansion of the films with increasing ion fluence, as determined by the HRXRD measurements. At a comparable level of lattice disorder, the Kr irradiation leads to a more pronounced lattice expansion than the Bi irradiation. This may be attributed to a larger portion of the single interstitials in the films produced by the lighter Kr ion irradiation.

  17. Investigations on imaging properties of inorganic scintillation screens under irradiation with high energetic heavy ions

    Energy Technology Data Exchange (ETDEWEB)

    Lieberwirth, Alice

    2016-09-15

    scintillation record was used to examine the material stability under long time application. Here, the light yield Y of the targets was nearly constant or decreased only in the range of 10-15 %, relative to the initial value. For the targets with single crystal characteristic (P46, YAG:Ce), Y even increased slightly and than saturated, offering an enhanced mobility of charge carriers under irradiation. The emission spectra were reproduced continuously and the beam profiles showed good accordance to the reference methods. Within all performed beam times, the targets offered a great stability. Non-linear characteristics, e.g. due to quenching during irradiation at high beam intensities, were not observed. The light yield Y showed a decreasing tendency as function of calculated electronic energy loss dE/dx. The characteristics of the calculated beam profiles, as well as the recorded emission spectra did not change significantly. So a material degradation in the investigated materials was not verified. This observation is confirmed by the performed material characterization measurements. The need of target replacement, e.g. due to damage, did not occur and was thus not performed during the complete investigations. As material for future beam diagnostics of FAIR cerium-doped Y{sub 3}Al{sub 5}O{sub 12} single crystal with a thickness in the range of 300 μm is recommended in cross-points between different storage sections, due to the stable imaging properties for high energy ion beams, even under long-time irradiation. For beam alignment to experimental and research areas, common Al{sub 2}O{sub 3}:Cr is recommended due to the cost advantage.

  18. Micro-structure and micro-hardness of ODS steels after ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Liu, C., E-mail: liuchxin@eng.hokudai.ac.jp [Graduate School of Engineering, Hokkaido University, Sapporo 060-8628 (Japan); Yu, C.; Hashimoto, N.; Ohnuki, S. [Graduate School of Engineering, Hokkaido University, Sapporo 060-8628 (Japan); Ando, M.; Shiba, K.; Jitsukawa, S. [Tokai Laboratory, JAEA, Tokai, Ibaraki 319-1195 (Japan)

    2011-10-01

    The radiation-hardening of oxide dispersion strengthened (ODS) alloys was examined using ion irradiation and nano-indentation. In this work, three ODS steels were irradiated in the TIARA facility at JAEA with 10.5 MeV Fe{sup 3+} ions up to a dose of 20 dpa at 250 and 380 deg. C. Micro-hardness measurements were carried out on the ion-irradiated specimens with ultra-low load indention. Micro-structures were investigated by transmission electron microscopy (TEM) to examine the contribution of various types of defects to the radiation-hardening. All three steels showed increases in the hardness after the ion irradiation, and F82H-ODS showed the lowest radiation-hardening, which suggests that F82H-ODS has the better radiation resistance. Small amounts of particle dissolution was also confirmed in all of the steels after the irradiation.

  19. Micro-structure and micro-hardness of ODS steels after ion irradiation

    Science.gov (United States)

    Liu, C.; Yu, C.; Hashimoto, N.; Ohnuki, S.; Ando, M.; Shiba, K.; Jitsukawa, S.

    2011-10-01

    The radiation-hardening of oxide dispersion strengthened (ODS) alloys was examined using ion irradiation and nano-indentation. In this work, three ODS steels were irradiated in the TIARA facility at JAEA with 10.5 MeV Fe 3+ ions up to a dose of 20 dpa at 250 and 380 °C. Micro-hardness measurements were carried out on the ion-irradiated specimens with ultra-low load indention. Micro-structures were investigated by transmission electron microscopy (TEM) to examine the contribution of various types of defects to the radiation-hardening. All three steels showed increases in the hardness after the ion irradiation, and F82H-ODS showed the lowest radiation-hardening, which suggests that F82H-ODS has the better radiation resistance. Small amounts of particle dissolution was also confirmed in all of the steels after the irradiation.

  20. Moessbauer study of FINEMET type nanocrystalline ribbons irradiated with swift heavy ions

    Energy Technology Data Exchange (ETDEWEB)

    Kuzmann, Erno, E-mail: kuzmann@ludens.elte.hu; Stichleutner, Sandor; Sapi, Andras [Institute of Chemistry, Eoetvoes University (Hungary); Varga, Lajos Karoly [Research Institute for Solid State Physics and Optics, HAS (Hungary); Havancsak, Karoly [Eoetvoes University, Department of Materials Physics (Hungary); Skuratov, Vlamidir [Joint Institute for Nuclear Research (Russian Federation); Homonnay, Zoltan; Vertes, Attila [Institute of Chemistry, Eoetvoes University (Hungary)

    2012-03-15

    As-quenched and stress field annealed FINEMET ribbons were irradiated with 246 MeV energy Kr, 470 MeV energy Xe and 720 MeV energy Bi ions and investigated by {sup 57}Fe Moessbauer spectroscopy and XRD methods. The change in relative areas of the 2nd and 5th lines in the Moessbauer spectra indicated significant changes in the magnetic anisotropy of both as-quenched and stress annealed FINEMET due to irradiation with swift heavy ions. Differences were observed between the effect of irradiations with various ions having different energy and fluence. The effect of irradiation on the magnetic orientation in FINEMET was explained in terms of radiation induced defects. The swift heavy ion irradiation can be applied to produce FINEMET ribbons with more favorable soft magnetic properties for technological applications.

  1. Effects of energetic ion irradiation on the magnetism of Fe–Ni Invar alloy

    Energy Technology Data Exchange (ETDEWEB)

    Matsushita, M., E-mail: matsushita@eng.ehime-u.ac.jp [Graduate School of Science and Engineering, Ehime University, 3-Bunkyocho, Matsuyama (Japan); Akamatsu, S. [Graduate School of Science and Engineering, Ehime University, 3-Bunkyocho, Matsuyama (Japan); Matsushima, Y. [Graduate School of Natural Science and Technology, Okayama University, Tsushima-naka Kitaku, Okayama (Japan); Iwase, A. [Department of Materials Science, Osaka Prefecture University, Gakuencho, Sakai (Japan)

    2013-11-01

    Highlights: •16-MeV Au{sup 3+} ions were irradiated to Fe{sub 66}Ni{sub 34} alloy. •Magnetic properties of Fe{sub 66}Ni{sub 34} were changed by the irradiation. •T{sub c} of a part of sample increases due to the irradiation. •FCC structure is stable before and after irradiation. -- Abstract: The magnetic properties of Fe–Ni Invar alloys are significantly affected by ion irradiation. Au{sup 3+} with the energy of 16 MeV irradiation effects on the magnetism of Fe{sub 66}Ni{sub 34} have been reported in this paper. Considering from the temperature variations of AC susceptibility of irradiated Fe{sub 66}Ni{sub 34}, Curie temperature of a part of sample increase with increasing incident ion fluence, and the magnetization of irradiated Fe{sub 66}Ni{sub 34} is also increase. The FCC structure of Fe{sub 66}Ni{sub 34} is not changed by ion irradiation; however peaks become broader with increasing ion fluence. It means that lattice fluctuations are generated owing to ion irradiation. However it cannot be considered that lattice fluctuations observed X-ray diffraction measurements are enough to increase the Curie temperature observed in AC susceptibility measurements. Then, we suggest as the considerable origin of increasing T{sub C}, atomic mixing effects owing to the ion irradiation. It might change the chemical ordering reported in the diffused scattering, such as Fe–Fe coupling.

  2. Effects of irradiation of energetic heavy ions on digital pulse shape analysis with silicon detectors

    Science.gov (United States)

    Barlini, S.; Carboni, S.; Bardelli, L.; Le Neindre, N.; Bini, M.; Borderie, B.; Bougault, R.; Casini, G.; Edelbruck, P.; Olmi, A.; Pasquali, G.; Poggi, G.; Rivet, M. F.; Stefanini, A. A.; Baiocco, G.; Berjillos, R.; Bonnet, E.; Bruno, M.; Chbihi, A.; Cruceru, I.; Degerlier, M.; Dueñas, J. A.; Galichet, E.; Gramegna, F.; Kordyasz, A.; Kozik, T.; Kravchuk, V. L.; Lopez, O.; Marchi, T.; Martel, I.; Morelli, L.; Parlog, M.; Piantelli, S.; Petrascu, H.; Rosato, E.; Seredov, V.; Vient, E.; Vigilante, M.; Fazia Collaboration

    2013-04-01

    The next generation of 4π detector arrays for heavy ion studies will largely use Pulse Shape Analysis to push the performance of silicon detectors with respect to ion identification. Energy resolution and pulse shape identification capabilities of silicon detectors under prolonged irradiation by energetic heavy ions have thus become a major issue. In this framework, we have studied the effects of irradiation by energetic heavy ions on the response of neutron transmutation doped (nTD) silicon detectors. Sizeable effects on the amplitude and the risetime of the charge signal have been found for detectors irradiated with large fluences of stopped heavy ions, while much weaker effects were observed by punching-through ions. The robustness of ion identification based on digital pulse shape techniques has been evaluated.

  3. Tuning the conductivity of vanadium dioxide films by swift heavy ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Ehrhardt, Paul; Hofsaess, Hans; Gehrke, Hans-Gregor [II. Physikalisches Institut, Fakultaet fuer Physik, Universitaet Goettingen, Friedrich-Hund-Platz 1, 37077 Goettingen (Germany); Krauser, Johann [Hochschule Harz, University of Applied Sciences, Friedrichstrasse 57-59, 38855 Wernigerode (Germany); Trautmann, Christina [Gesellschaft fuer Schwerionenforschung, Planckstrasse 1, 64291 Darmstadt (Germany); Ramanathan, Shriram [Harvard School of Engineering and Applied Sciences, Harvard University, Cambridge, MA 02138 (United States)

    2012-07-01

    We demonstrate the generation of a persistent conductivity increase in vanadium dioxide thin films by irradiation with swift heavy ions at room temperature. VO{sub 2} undergoes a temperature driven metal-insulator-transition (MIT) at 67 C. After the ion irradiation the conductivity of the films we observe a strong increase in conductivity below the transition temperature proportional to the ion fluence. This change in conductivity is persistent and remains after several cycles of heating. Low temperature measurements down to 15 K show no further MIT below room temperature. Although the conductivity increase after irradiation at such low fluences is due to single ion track effects, atomic force microscopy (AFM) measurements do not show surface hillocks, which are characteristic for ion tracks in other materials. AFM measurements with conducting tip give no evidence for conducting ion tracks but indicate the existence of conducting regions around poorly conducting ion tracks, possible due to stress generation.

  4. Microanalysis on the Hydrogen Ion Irradiated 50 wt pct TiC-C Films

    Institute of Scientific and Technical Information of China (English)

    Hui JIANG; Yaoguang LIU; Ningkang HUANG

    2007-01-01

    The 50 wt pct TiC-C films were prepared on stainless steel substrates by using a technique of ion beam mixing.These films were irradiated by hydrogen ion beam with a dose of 1×1018 ions/cm2 and an energy of 5 keV.Microanalysis of X-ray photoelectron spectroscopy (XPS) and secondary ion mass spectroscopy (SIMS) were used to analyze the films before and after hydrogen ion irradiation and to study the mechanism of hydrogen resistance.

  5. Structure evolution of mesoporous silica SBA-15 and MCM-41 under swift heavy ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Lou, Y.; Toquer, G.; Dourdain, S.; Rey, C. [ICSM-UMR 5257, CEA/CNRS/UM2/ENSCM Marcoule, BP 17171, F-30207 Bagnols-sur-Cèze (France); Grygiel, C. [CIMAP GANIL, Bd. Henri Becquerel, BP 5133, F-14070 Caen CEDEX 5 (France); Simeone, D. [CEA, DEN, LRC CARMEN, CEA Saclay, F-91191 Gif/Yvette (France); Deschanels, X., E-mail: xavier.deschanels@cea.fr [ICSM-UMR 5257, CEA/CNRS/UM2/ENSCM Marcoule, BP 17171, F-30207 Bagnols-sur-Cèze (France)

    2015-12-15

    Two types of mesoporous silica pellets, SBA-15 and MCM-41, were prepared and irradiated by {sup 20}Ne 278 MeV (max. fluence = 2.5 × 10{sup 14} ion/cm{sup 2}) and {sup 36}Ar 493 MeV beams (max. fluence = 1 × 10{sup 13} ion/cm{sup 2}). Irradiated and non-irradiated samples were characterized by nitrogen adsorption/desorption analysis, small angle X-ray scattering, and infrared spectrometry. The different behaviours of the two materials under different conditions are observed and discussed. We point out that SBA-15 is more robust than MCM-41 under irradiation.

  6. Structure evolution of mesoporous silica SBA-15 and MCM-41 under swift heavy ion irradiation

    Science.gov (United States)

    Lou, Y.; Toquer, G.; Dourdain, S.; Rey, C.; Grygiel, C.; Simeone, D.; Deschanels, X.

    2015-12-01

    Two types of mesoporous silica pellets, SBA-15 and MCM-41, were prepared and irradiated by 20Ne 278 MeV (max. fluence = 2.5 × 1014 ion/cm2) and 36Ar 493 MeV beams (max. fluence = 1 × 1013 ion/cm2). Irradiated and non-irradiated samples were characterized by nitrogen adsorption/desorption analysis, small angle X-ray scattering, and infrared spectrometry. The different behaviours of the two materials under different conditions are observed and discussed. We point out that SBA-15 is more robust than MCM-41 under irradiation.

  7. Variation in viscosity and ion conductivity of a polymer–salt complex exposed to gamma irradiation

    Indian Academy of Sciences (India)

    Sujata Tarafdar; S K De; Sujit Manna; Udayan De; Pradyot Nanda

    2010-02-01

    We study changes in microstructure and resulting changes in the properties of PEO(1 − )–NH4 ClO4 () samples where = 0.18, when irradiated with gamma doses varying up to 50 kGy. Viscosities of aqueous solutions of the irradiated samples give an idea of the change in molecular weight and show correlation with ion conductivity. On the whole, there is a chain scission on irradiation, though there is evidence of some cross-linking at higher doses. The ion conductivity shows a strong increase for an irradiation of 35 kGy. DSC studies indicate a decrease in crystallinity with gamma dose.

  8. Precipitation of the Carbides $M_{23}C_{6}$ under the Irradiation by High Energy Heavy Ions

    CERN Document Server

    Hofmann, A; Semina, V K; Kochanski, T

    2000-01-01

    Carbide M_{23}C_{6} precipitation process in chromium-nickel steels 12H18N9ô and 00H17N14í2 irradiated with high energy heavy Ar^{+6} ions at 625^{o}ó has been studied. It was found that ion irradiation accelerates carbide M_{23}C_{6} precipitation in comparison to thermal annealing. It was shown that composition of carbides formed by irradiation in 00H17N14í2 steel formed under irradiation differs from composition of carbides precipitated during thermal ageing.

  9. Influence of high energy ion irradiation on fullerene derivative (PCBM) thin films

    Energy Technology Data Exchange (ETDEWEB)

    Sharma, Trupti, E-mail: tsphy91@gmail.com [Department of Physics, Malaviya National Institute of Technology, Jaipur 302017 (India); Singhal, Rahul; Vishnoi, Ritu [Department of Physics, Malaviya National Institute of Technology, Jaipur 302017 (India); Lakshmi, G.B.V.S. [Inter University Accelerator Centre, Post Box No. 10502, New Delhi 110067 (India); Biswas, S.K. [Department of Metallurgical and Materials Engineering, Malaviya National Institute of Technology, Jaipur 302017 (India)

    2017-04-01

    Highlights: • Spin casted PCBM thin films (∼100 nm) are irradiated with 55 MeV Si{sup 4+} ion beam. • The decrease in band gap is observed after irradiation. • The surface properties is also dependent on incident ion fluences. • Polymerization reactions induced by energetic ions leads to modifications. - Abstract: The modifications produced by 55 MeV Si{sup 4+} swift heavy ion irradiation on the phenyl C{sub 61} butyric acid methyl ester (PCBM) thin films (thickness ∼ 100 nm) has been enlightened. The PCBM thin films were irradiated at 1 × 10{sup 10}, 1 × 10{sup 11} and 1 × 10{sup 12} ions/cm{sup 2} fluences. After ion irradiation, the decreased optical band gap and FTIR band intensities were observed. The Raman spectroscopy reveals the damage produced by energetic ions. The morphological variation were investigated by atomic force microscopy and contact angle measurements and observed to be influenced by incident ion fluences. After 10{sup 11} ions/cm{sup 2} fluence, the overlapping of ion tracks starts and produced overlapping effects.

  10. Radiation effects of pyrochlore-rich synroc by heavy-ion irradiation

    Institute of Scientific and Technical Information of China (English)

    YANG Jian-Wen; XU Yong-Jun; ZHU Sheng-Yun; LUO Shang-Geng

    2005-01-01

    Heavy-ion irradiation is commonly used to study radiation damage of high level radioactive waste (HLW)forms, but S ion was never used before. In this investigation, 100 MeV 32S ions produced by tandem accelerator was used to study radiation effects on pyrochlore-rich synroc which contained simulated actinides. The amorphization and amorphous doses were determined by X-ray diffractometer (XRD) and transmission electron microscopy/select area electron diffraction (TEM/SAED). The vacancy defects induced by heavy-ion irradiation were characterized by using positron annihilation technique (PAT). The experimental results show that the amorphous dose is 0.5 dpa, the defects produced by heavy-ion irradiation are mainly voids, and irradiation could continue to intensify the vacancy defects even after the amorphous dose was reached.

  11. Calculation of response and thindown of V-79 cell for ion irradiation

    Institute of Scientific and Technical Information of China (English)

    CHEN Li-Xin; LIU Xiao-Wei

    2004-01-01

    A cellular survival model and the cross section calculation with low and high LET for ion irradiation were presented. Based on our formula of surviving fraction calculation, the survival data of Chinese hamster cell (V-79)for ion irradiation including He, Li, B, C, O, Ne and Ar were calculated; the cross sections for ion irradiation including He, Ni, C, Ar, Kr, Xe and U were shown. The calculated results show that the presented model is a good description of radiation effects of V-79 cell for different ion irradiation. In this model splitting energy between ion-kill mode and gamma-kill model is avoided, the calculated results of cross section needn't be multiplied by a factor to fit the experimental data.

  12. Ion desorption from frozen H 2O irradiated by MeV heavy ions

    Science.gov (United States)

    Collado, V. M.; Farenzena, L. S.; Ponciano, C. R.; Silveira, E. F. da; Wien, K.

    2004-10-01

    Nitrogen (0.13-0.85 MeV) and 252Cf fission fragments (˜65 MeV) beams are employed to sputter positive and negative secondary ions from frozen water. Desorption yields are measured for different ice temperatures and projectile energies. Target surface is continuously refreshed by condensed water while the target temperature varies and ice thickness changes. In both projectile energy ranges, the preferentially ejected ions are H +, H2+ and (H 2O) nH +-cluster ions. The yields of the corresponding negative ions H - and (H 2O) nO - or (H 2O) nOH - are 1-2 orders of magnitude lower. The (H 2O) nH + desorption yields decrease exponentially as the cluster size, n, increases. In the low energy range, the desorption of positive ion clusters may occur in a two-step process: first, desorption of preformed H 2O clusters and, then, ionization by H + or H 3O + capture. For 0.81 MeV N + projectile ions, the cluster ion emission contributes with 0.05% to the total H 2O desorbed yield. There are indications that emission of the (H 2O) nH + disappears for an electronic energy loss lower than 20 eV/Å. For the high energy range, desorption of small ion clusters is particularly enhanced, revealing that a fragmentation process also exists.

  13. Luminescence imaging of water during carbon-ion irradiation for range estimation.

    Science.gov (United States)

    Yamamoto, Seiichi; Komori, Masataka; Akagi, Takashi; Yamashita, Tomohiro; Koyama, Shuji; Morishita, Yuki; Sekihara, Eri; Toshito, Toshiyuki

    2016-05-01

    The authors previously reported successful luminescence imaging of water during proton irradiation and its application to range estimation. However, since the feasibility of this approach for carbon-ion irradiation remained unclear, the authors conducted luminescence imaging during carbon-ion irradiation and estimated the ranges. The authors placed a pure-water phantom on the patient couch of a carbon-ion therapy system and measured the luminescence images with a high-sensitivity, cooled charge-coupled device camera during carbon-ion irradiation. The authors also carried out imaging of three types of phantoms (tap-water, an acrylic block, and a plastic scintillator) and compared their intensities and distributions with those of a phantom containing pure-water. The luminescence images of pure-water phantoms during carbon-ion irradiation showed clear Bragg peaks, and the measured carbon-ion ranges from the images were almost the same as those obtained by simulation. The image of the tap-water phantom showed almost the same distribution as that of the pure-water phantom. The acrylic block phantom's luminescence image produced seven times higher luminescence and had a 13% shorter range than that of the water phantoms; the range with the acrylic phantom generally matched the calculated value. The plastic scintillator showed ∼15 000 times higher light than that of water. Luminescence imaging during carbon-ion irradiation of water is not only possible but also a promising method for range estimation in carbon-ion therapy.

  14. Multivariate analysis of Ion Beam Induced Luminescence spectra of irradiated silver ion-exchanged silicate glasses

    Science.gov (United States)

    Valotto, Gabrio; Quaranta, Alberto; Cattaruzza, Elti; Gonella, Francesco; Rampazzo, Giancarlo

    A multivariate analysis is used for the identification of the spectral features in Ion Beam Induced Luminescence (IBIL) spectra of soda-lime silicate glasses doped with silver by Ag+-Na+ ion exchange. Both Principal Component Analysis and multivariate analysis were used to characterize time-evolving IBIL spectra of Ag-doped glasses, by means of the identification of the number and of the wavelength positions of the main luminescent features and the study of their evolution during irradiation. This method helps to identify the spectral features of the samples spectra, even when partially overlapped or less intense. This analysis procedure does not require additional input such as the number of peaks.

  15. Influence of Low-Energy Ion Irradiation on Plasma MembranePermeability of Cells

    Institute of Scientific and Technical Information of China (English)

    ZHANG Dong-Mei; CUI Fu-Zhai; SUN Su-Qin; LIN You-Bo; TIAN Min-Bo; CHEN Guo-Qiang

    2000-01-01

    Effect of low-energy ion irradiation on plasma membrane permeability has been investigated by using electron spin resonance (ESR) spectroscopy of spin probe technique. The investigated system is plumule cells of wheat (Triticum aestivum L.) seeds implanted by 30keV N+ ions. ESR spectra indicated that plasmalemma permeability is sensitive to low-energyion irradiation. Ion irradiations with increasing fluences up to semi-lethal dose lead to gradual increase in plasmalemma permeability of the plumule cells. The possible factors relevant to the changes in membrane permeability are discussed in relation to the changes in the physical state and chemical nature of membranes.

  16. Irradiation effects of swift heavy ions in matter

    Energy Technology Data Exchange (ETDEWEB)

    Osmani, Orkhan

    2011-12-22

    In the this thesis irradiation effects of swift heavy ions in matter are studied. The focus lies on the projectiles charge exchange and energy loss processes. A commonly used computer code which employs rate equations is the so called ETACHA code. This computer code is capable to also calculate the required input cross-sections. Within this thesis a new model to compute the charge state of swift heavy ions is explored. This model, the so called matrix method, takes the form of a simple algebraic expression, which also requires cross-sections as input. In the present implementation of the matrix method, cross-sections are taken from the ETACHA code, while excitation and deexcitation processes are neglected. Charge fractions for selected ion/target combinations, computed by the ETACHA code and the matrix method are compared. It is shown, that for sufficient large ion energies, both methods agree very well with each other. However, for lower energies pronounced differences are observed. These differences are believed to stem from the fact, that no excited states as well as the decay of theses excited states are included in the present implementation of the matrix method. Both methods are then compared with experimental measurements, where significant deviations are observed for both methods. While the predicted equilibrium charge state by both methods is in good agreement with the experiments, the matrix method predicts a much too large equilibrium thickness compared to both the ETACHA calculation as well as the experiment. Again, these deviations are believed to stem from the fact, that excitation and the decay of excited states are not included in the matrix method. A possible way to include decay processes into the matrix method is presented, while the accuracy of the applied capture cross-sections is tested by comparison with scaling rules. Swift heavy ions penetrating a dielectric are known to induced structural modifications both on the surface and in the bulk

  17. Incoherent twin boundary migration induced by ion irradiation in Cu

    Energy Technology Data Exchange (ETDEWEB)

    Li, N.; Misra, A. [Center for Integrated Nanotechnologies, Materials Physics and Applications Division, Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States); Wang, J.; Wang, Y. Q. [Materials Science and Technology Division, MST-8, Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States); Serruys, Y. [CEA, DEN, Service de Recherches de Metallurgie Physique, Laboratoire JANNUS, F-91191 Gif-sur-Yvette (France); Nastasi, M. [Nebraska Center for Energy Sciences Research, University of Nebraska, Lincoln, Nebraska 68588 (United States)

    2013-01-14

    Grain boundaries can act as sinks for radiation-induced point defects. The sink capability is dependent on the atomic structures and varies with the type of point defects. Using high-resolution transmission electron microscopy, we observed that {Sigma}3{l_brace}112{r_brace} incoherent twin boundary (ITB) in Cu films migrates under Cu{sup 3+} ion irradiation. Using atomistic modeling, we found that {Sigma}3{l_brace}112{r_brace} ITB has the preferred sites for adsorbing interstitials and the preferential diffusion channels along the Shockley partial dislocations. Coupling with the high mobility of grain boundary Shockley dislocations within {Sigma}3{l_brace}112{r_brace} ITB, we infer that {Sigma}3{l_brace}112{r_brace} ITB migrates through the collective glide of grain boundary Shockley dislocations, driven by a concurrent reduction in the density of radiation-induced defects, which is demonstrated by the distribution of nearby radiation-induced defects.

  18. Defects in 700 keV oxygen ion irradiated ZnO

    Energy Technology Data Exchange (ETDEWEB)

    Pal, S. [Department of Physics, University of Calcutta, 92 Acharya Prafulla Chandra Road, Kolkata 700009 (India); Sarkar, A. [Department of Physics, Bangabasi Morning College, 19 Rajkumar Chakraborty Sarani, Kolkata 700009 (India); Chattopadhyay, S. [Department of Basic Science and Humanities, Calcutta Institute of Engineering and Management, 24/1A Chandi Ghosh Road, Kolkata 700040 (India); Chakrabarti, Mahuya [Department of Physics, University of Calcutta, 92 Acharya Prafulla Chandra Road, Kolkata 700009 (India); Sanyal, D. [Variable Energy Cyclotron Centre, 1/AF Bidhannagar, Kolkata 700064 (India); Kumar, P.; Kanjilal, D. [Inter-University Accelerator Centre, P.O. Box 10502, Aruna Asaf Ali Marg, New Delhi 110067 (India); Rakshit, T.; Ray, S.K. [Department of Physics and Meteorology, Indian Institute of Technology, Kharagpur 721302 (India); Jana, D., E-mail: djphy@caluniv.ac.in [Department of Physics, University of Calcutta, 92 Acharya Prafulla Chandra Road, Kolkata 700009 (India)

    2013-09-15

    Highlights: •ZnO samples (both poly and single crystal) have been irradiated with 700 keV O ions. •Non-monotonic variation of room temperature sheet resistance has been observed. •NBE PL emission is largely reduced due to O ion irradiation. •Absorption spectrum of irradiated ZnO crystal show a sub-band gap absorption. •Oxygen irradiation generated new absorption band in ZnO is at 3.05 eV. -- Abstract: It is well known that energetic oxygen ions induce heavy crystalline disorder in ZnO, however, systematic study on this regard is very much limited. Here, we present photoluminescence (PL), optical absorption and sheet resistance measurements on poly and single crystalline ZnO samples irradiated with 700 keV O ions. Results have been compared with the effects of 1.2 MeV Ar irradiation on similar ZnO target. Colour change of the samples with increasing O irradiation fluence has also been noted. Non-monotonic variation of room temperature sheet resistance with the increase of fluence has been observed for polycrystalline ZnO. Such an outcome has been understood as point defects transforming to bigger size clusters. Near band edge (NBE) PL emission is largely reduced due to O ion irradiation. However, at 10 K NBE emission can be observed for irradiated polycrystalline samples. Irradiated ZnO single crystal does not show any band to band transition even at 10 K. It is evident that dynamic recovery of defects is more effective in polycrystalline samples. Ultraviolet–visible absorption spectrum of the irradiated ZnO crystal show pronounced sub-band gap absorption. Oxygen irradiation generated new absorption band in ZnO is at 3.05 eV. In the light of earlier reports, this particular band can be ascribed to absorption by neutral oxygen vacancy defects.

  19. Temperature-dependent surface porosity of Nb2O5 under high-flux, low-energy He+ ion irradiation

    Science.gov (United States)

    Novakowski, T. J.; Tripathi, J. K.; Hosinski, G. M.; Joseph, G.; Hassanein, A.

    2016-01-01

    The present study reports on high-flux, low-energy He+ ion irradiation as a novel method of enhancing the surface porosity and surface area of naturally oxidized niobium (Nb). Our study shows that ion-irradiation-induced Nb surface micro- and nano-structures are highly tunable by varying the target temperature during ion bombardment. Mirror-polished Nb samples were irradiated with 100 eV He+ ions at a flux of 1.2 × 1021 ions m-2 s-1 to a total fluence of 4.3 × 1024 ions m-2 with simultaneous sample annealing in the temperature range of 773-1223 K to demonstrate the influence of sample temperature on the resulting Nb surface morphology. This surface morphology was primarily characterized using field-emission scanning electron microscopy (FE-SEM) and atomic force microscopy (AFM). Below 923 K, Nb surfaces form nano-scale tendrils and exhibit significant increases in surface porosity. Above 923 K, homogeneously populated nano-pores with an average diameter of ∼60 nm are observed in addition to a smaller population of sub-micron sized pores (up to ∼230 nm in diameter). Our analysis shows a significant reduction in surface pore number density and surface porosity with increasing sample temperature. High-resolution ex situ X-ray photoelectron spectroscopy (XPS) shows Nb2O5 phase in all of the ion-irradiated samples. To further demonstrate the length scales in which radiation-induced surface roughening occurs, optical reflectivity was performed over a spectrum of light between 200 and 1100 nm, showing a recovery of nano-scale surface damage at high sample temperatures.

  20. Comparison of UV and high-energy ion irradiation of methanol:ammonia ice

    CERN Document Server

    Caro, G M Munoz; Boduch, P; Rothard, H; Domaracka, A; Jimenez-Escobar, A

    2014-01-01

    The main goal of this work is to compare the effects induced in ices of astrophysical relevance by high-energy ions, simulating cosmic rays, and by vacuum ultraviolet (UV) photons. This comparison relies on in situ infrared spectroscopy of irradiated CH3OH:NH3 ice. Swift heavy ions were provided by the GANIL accelerator. The source of UV was a microwave-stimulated hydrogen flow discharge lamp. The deposited energy doses were similar for ion beams and UV photons to allow a direct comparison. A variety of organic species was detected during irradiation and later during ice warm-up. These products are common to ion and UV irradiation for doses up to a few tens of eV per molecule. Only the relative abundance of the CO product, after ice irradiation, was clearly higher in the ion irradiation experiments. For some ice mixture compositions, the irradiation products formed depend only weakly on the type of irradiation, swift heavy ions, or UV photons. This simplifies the chemical modeling of energetic ice processing ...

  1. Refractive index dispersion of swift heavy ion irradiated BFO thin films using Surface Plasmon Resonance technique

    Energy Technology Data Exchange (ETDEWEB)

    Paliwal, Ayushi [Department of Physics and Astrophysics, University of Delhi, Delhi 110007 (India); Sharma, Savita [Department of Applied Physics, Delhi Technological University, Delhi (India); Tomar, Monika [Physics Department, Miranda House, University of Delhi, Delhi 110007 (India); Singh, Fouran [Inter University Accelerator Centre, Aruna Asaf Ali Marg, New Delhi 110075 (India); Gupta, Vinay, E-mail: drguptavinay@gmail.com [Department of Physics and Astrophysics, University of Delhi, Delhi 110007 (India)

    2016-07-15

    Highlights: • Investigated the optical properties of BiFeO{sub 3} (BFO) thin films after irradiation using SPR. • Otto configuration has been used to excite the surface plasmons using gold metal thin film. • BFO thin films were prepared by sol–gel spin coating technique. • Examined the refractive index dispersion of pristine and irradiated BFO thin film. - Abstract: Swift heavy ion irradiation (SHI) is an effective technique to induce defects for possible modifications in the material properties. There is growing interest in studying the optical properties of multiferroic BiFeO{sub 3} (BFO) thin films for optoelectronic applications. In the present work, BFO thin films were prepared by sol–gel spin coating technique and were irradiated using the 15 UD Pelletron accelerator with 100 MeV Au{sup 9+} ions at a fluence of 1 × 10{sup 12} ions cm{sup −2}. The as-grown films became rough and porous on ion irradiation. Surface Plasmon Resonance (SPR) technique has been identified as a highly sensitive and powerful technique for studying the optical properties of a dielectric material. Optical properties of BFO thin films, before and after irradiation were studied using SPR technique in Otto configuration. Refractive index is found to be decreasing from 2.27 to 2.14 on ion irradiation at a wavelength of 633 nm. Refractive index dispersion of BFO thin film (from 405 nm to 633 nm) before and after ion radiation was examined.

  2. Ion irradiation induced structural modifications and increase in elastic modulus of silica based thin films

    Science.gov (United States)

    Shojaee, S. A.; Qi, Y.; Wang, Y. Q.; Mehner, A.; Lucca, D. A.

    2017-01-01

    Ion irradiation is an alternative to heat treatment for transforming organic-inorganic thin films to a ceramic state. One major shortcoming in previous studies of ion-irradiated films is the assumption that constituent phases in ion-irradiated and heat-treated films are identical and that the ion irradiation effect is limited to changes in composition. In this study, we investigate the effects of ion irradiation on both the composition and structure of constituent phases and use the results to explain the measured elastic modulus of the films. The results indicated that the microstructure of the irradiated films consisted of carbon clusters within a silica matrix. It was found that carbon was present in a non-graphitic sp2-bonded configuration. It was also observed that ion irradiation caused a decrease in the Si-O-Si bond angle of silica, similar to the effects of applied pressure. A phase transformation from tetrahedrally bonded to octahedrally bonded silica was also observed. The results indicated the incorporation of carbon within the silica network. A combination of the decrease in Si-O-Si bond angle and an increase in the carbon incorporation within the silica network was found to be responsible for the increase in the elastic modulus of the films. PMID:28071696

  3. Effect of ion irradiation on the surface, structural and mechanical properties of brass

    Science.gov (United States)

    Ahmad, Shahbaz; Bashir, Shazia; Ali, Nisar; Umm-i-Kalsoom; Yousaf, Daniel; Faizan-ul-Haq; Naeem, Athar; Ahmad, Riaz; Khlaeeq-ur-Rahman, M.

    2014-04-01

    Modifications to the surface, structural and mechanical properties of brass after ion irradiation have been investigated. Brass targets were bombarded by carbon ions of 2 MeV energy from a Pelletron linear accelerator for various fluences ranging from 56 × 1012 to 26 × 1013 ions/cm2. A scanning electron microscope and X-ray diffractometer were utilized to analyze the surface morphology and crystallographic structure respectively. To explore the mechanical properties e.g., yield stress, ultimate tensile strength and microhardness of irradiated brass, an universal tensile testing machine and Vickers microhardness tester were used. Scanning electron microscopy results revealed an irregular and randomly distributed sputter morphology for a lower ion fluence. With increasing ion fluence, the incoherently shaped structures were transformed into dendritic structures. Nano/micro sized craters and voids, along with the appearance of pits, were observed at the maximum ion fluence. From X-ray diffraction results, no new phases were observed to be formed in the brass upon irradiation. However, a change in the peak intensity and higher and lower angle shifting were observed, which represents the generation of ion-induced defects and stresses. Analyses confirmed modifications in the mechanical properties of irradiated brass. The yield stress, ultimate tensile strength and hardness initially decreased and then increased with increasing ion fluence. The changes in the mechanical properties of irradiated brass are well correlated with surface and crystallographic modifications and are attributed to the generation, augmentation, recombination and annihilation of the ion-induced defects.

  4. Effect of swift heavy ion irradiation on hydrothermally synthesized hydroxyapatite ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Parthiban, S. Prakash; Suganthi, R.V.; Girija, E.K.; Elayaraja, K. [Crystal Growth Centre, Anna University, Chennai 600 025 (India); Kulriya, P.K.; Katharria, Y.S.; Singh, F.; Sulania, I.; Tripathi, A.; Asokan, K.; Kanjilal, D. [Inter University Accelerator Centre, P.O. Box 10502, New Delhi 110 067 (India); Yadav, S.; Singh, T.P. [Department of Biophysics, All India Institute of Medical Sciences, New Delhi 110 029 (India); Yokogawa, Y. [Graduate School of Engineering, Department of Intelligent Materials Engineering, Osaka City University (OCU), Osaka 558-8585 (Japan); Kalkura, S. Narayana [Crystal Growth Centre, Anna University, Chennai 600 025 (India)], E-mail: kalkura@yahoo.com

    2008-03-15

    The effect of swift heavy ion irradiation on hydroxyapatite (HAp) ceramic - a bone mineral was investigated. The irradiation experiment was conducted using oxygen ions at energy of 100 MeV with three different fluences of 10{sup 12}, 10{sup 13}, 10{sup 14} ions/cm{sup 2}. The irradiated samples were characterized by glancing angle X-ray diffraction (GXRD), atomic force microscopy (AFM), dynamic light scattering (DLS), photoluminescence spectroscopy (PL), scanning electron microscopy (SEM) and energy dispersive X-ray analysis (EDAX). GXRD confirmed incomplete amorphisation of HAp with increase in fluence. There was considerable reduction in particle size on irradiation leading to nanosized HAp (upto 53 nm). PL studies showed emission in the visible wavelength region. The irradiated samples exhibited better bioactivity than the pristine HAp.

  5. Study of swift (100 MeV) Fe{sup 9+} ion irradiated gallium antimonide

    Energy Technology Data Exchange (ETDEWEB)

    Jadhav, Vidya [Department of Physics, University of Mumbai, Santacruz (E), Mumbai 400 098 (India); Dubey, S.K. [Department of Physics, University of Mumbai, Santacruz (E), Mumbai 400 098 (India)], E-mail: skdubey@physics.mu.ac.in; Dubey, R.L.; Tripathi, S.; Yadav, A.D.; Gupta, S.J. [Department of Physics, University of Mumbai, Santacruz (E), Mumbai 400 098 (India); Gundu Rao, T.K. [SAIF, Indian Institute of Technology, Powai, Mumbai 400 076 (India); Kanjilal, D. [Inter University Accelerator Centre, Aruna Asaf Ali Marg, New Delhi 110 067 (India)

    2008-04-15

    The effect of 100 MeV irradiation of iron ions in p-type gallium antimonide for ion fluences varying from 1 x 10{sup 11} to 5 x 10{sup 13} cm{sup -2} was investigated using Raman scattering, Fourier transform infrared and X-ray diffraction measurements. Raman spectra showed a strong peak at 232.82 cm{sup -1} (LO) and a weak peak at 223.79 cm{sup -1} (TO). The peaks were shifted towards higher wave number compared to non-irradiated sample indicating the presence of stress in the irradiated samples. The increase of optical absorbance of samples irradiated with different fluences indicates the increase in the amount of disorder and defect concentrations with fluence. The intensity of the XRD peak (2{theta} = 61.07 degree) of the irradiated samples for (4 0 0) reflections was found to decrease with ion fluence.

  6. Optical properties of swift ion beam irradiated CdTe thin films

    Energy Technology Data Exchange (ETDEWEB)

    Chandramohan, S. [PG and Research Department of Physics, Kongunadu Arts and Science College, Coimbatore, Tamilnadu 641029 (India); Sathyamoorthy, R. [PG and Research Department of Physics, Kongunadu Arts and Science College, Coimbatore, Tamilnadu 641029 (India)], E-mail: rsathya59@yahoo.co.in; Sudhagar, P. [PG and Research Department of Physics, Kongunadu Arts and Science College, Coimbatore, Tamilnadu 641029 (India); Kanjilal, D.; Kabiraj, D.; Asokan, K. [Inter-University Accelerator Centre, Aruna Asaf Ali Marg, New Delhi 110067 (India)

    2008-06-30

    This paper reports the effect of swift (80 MeV) oxygen (O{sup +6}) ion irradiation on the optical properties of CdTe thin films grown by conventional thermal evaporation on glass substrates. The films are found to be slightly Te-rich in composition and irradiation results no change in the elemental composition. The optical constants such as refractive index (n), absorption coefficient ({alpha}) and the optical band gap energy show significant variation in their values with increase in ion fluence. Upon irradiation the band gap energy decreased from a value of 1.53 eV to 1.46 eV whereas the refractive index (n) increased from 2.38 to 3.12 at {lambda} = 850 nm. The photoluminescence spectrum shows high density of native defects whose density strongly depends on the ion fluence. Both analyses indicate considerable defect production after swift ion beam irradiation.

  7. Distribution of products in polymer materials induced by ion-beam irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Sugimoto, Masaki; Kudoh, Hisaaki; Sasuga, Tsuneo; Seguchi, Tadao [Japan Atomic Energy Research Inst., Tokyo (Japan); Hama, Yoshimasa; Hamanaka, Ken-ichi; Matsumoto, Hideya

    1997-03-01

    The depth profile of double bond formed in low density polyethylene (LDPE) sheet by ion beams irradiation was observed by a micro FT-IR spectrometer in order to investigate the linear energy transfer (LET) dependency on radiation effects to polymer materials. The distribution of double bond formation in LDPE by irradiation of light ions as H+ was found to be same with the dose distribution calculated from TRIM code, and the yield was also same with that by gamma-rays irradiation, which means that the LET dependency is very small. However, the distribution of double bond to depth was much different from the calculated depth-dose in heavy ions irradiation as Ar and Kr. Then, the dose evaluation was difficult from the TRIM code calculation for heavy ions. (author)

  8. Fluorescence enhancement of photoswitchable metal ion sensors

    Science.gov (United States)

    Sylvia, Georgina; Heng, Sabrina; Abell, Andrew D.

    2016-12-01

    Spiropyran-based fluorescence sensors are an ideal target for intracellular metal ion sensing, due to their biocompatibility, red emission frequency and photo-controlled reversible analyte binding for continuous signal monitoring. However, increasing the brightness of spiropyran-based sensors would extend their sensing capability for live-cell imaging. In this work we look to enhance the fluorescence of spiropyran-based sensors, by incorporating an additional fluorophore into the sensor design. We report a 5-membered monoazacrown bearing spiropyran with metal ion specificity, modified to incorporate the pyrene fluorophore. The effect of N-indole pyrene modification on the behavior of the spiropyran molecule is explored, with absorbance and fluorescence emission characterization. This first generation sensor provides an insight into fluorescence-enhancement of spiropyran molecules.

  9. Effect of 100MeV oxygen ion irradiation on silicon NPN power transistor

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, M. Vinay; Krishnakumar, K. S.; Dinesh, C. M.; Krishnaveni, S.; Ramani [Department of studies in Physics, University of Mysore, Mysore (India); Department of Physics, APS College, Bengaluru (India); Department of Physics, DCE, Govt. First Grade College, Mangalore (India); Department of studies in Physics, University of Mysore, Mysore (India); Department of Physics, Bangalore University, Bengaluru (India)

    2012-06-05

    The radiation response of npn Bipolar junction transistor (BJT) has been examined for 100 MeV O{sup 7+} ion. Key electrical properties like Gummel characteristics, dc current gain and capacitance-voltage of 100MeV O{sup 7+} ion irradiated transistor were studied before and after irradiation. The device was decapped and the electrical characterizations were performed at room temperature. Base current is observed to be more sensitive than collector current and gain appears to be degraded with ion fluence, also considerable degradation in C-V characteristics is observed and doping concentration is found to be increased along with the increase in ion fluence.

  10. Effect of 100MeV oxygen ion irradiation on silicon NPN power transistor

    Science.gov (United States)

    Kumar, M. Vinay; Krishnakumar, K. S.; Dinesh, C. M.; Krishnaveni, S.; Ramani

    2012-06-01

    The radiation response of npn Bipolar junction transistor (BJT) has been examined for 100 MeV O7+ ion. Key electrical properties like Gummel characteristics, dc current gain and capacitance-voltage of 100MeV O7+ ion irradiated transistor were studied before and after irradiation. The device was decapped and the electrical characterizations were performed at room temperature. Base current is observed to be more sensitive than collector current and gain appears to be degraded with ion fluence, also considerable degradation in C-V characteristics is observed and doping concentration is found to be increased along with the increase in ion fluence.

  11. Irradiation damage in aluminium single crystals produced by 50-keV aluminium and copper ions

    DEFF Research Database (Denmark)

    Henriksen, L.; Johansen, A.; Koch, J.

    1968-01-01

    Aluminium single crystals, thin enough to be examined by electron microscopy, have been irradiated with 50-keV aluminium and copper ions. The irradiation fluxes were in the range 1011–1014 cm−2 s−1 and the doses were from 6 × 1012 to 6 × 1014 cm−2. Irradiation along either a or a direction produc...

  12. Effect of 100 MeV Ag+7 ion irradiation on the bulk and surface magnetic properties of Co-Fe-Si thin films

    Science.gov (United States)

    Hysen, T.; Geetha, P.; Al-Harthi, Salim; Al-Omari, I. A.; Lisha, R.; Ramanujan, R. V.; Sakthikumar, D.; Avasthi, D. K.; Anantharaman, M. R.

    2014-12-01

    Thin films of Co-Fe-Si were vacuum evaporated on pre-cleaned float glass substrates employing thermal evaporation. The films were subsequently irradiated with 100 MeV Ag+7 ions at fluences of 1×1011, 1×1012 and 1×1013 ions/cm2. The pristine and irradiated samples were subjected to surface analysis using Atomic Force Microscopy (AFM), Vibrating Sample Magnetometry (VSM) and Magneto Optic Kerr Effect (MOKE) measurements. The as deposited film has a root mean square roughness (Rq) of 8.9 nm and an average roughness of (Ra) 5.6 nm. Irradiation of the as deposited films with 100 MeV Ag7+ ions modifies the surface morphology. Irradiating with ions at fluences of 1×1011 ions/cm2 smoothens the mesoscopic hill-like structures, and then, at 1×1012 ions/cm2 new surface structures are created. When the fluence is further increased to 1×1013 ions/cm2 an increase in the surface roughness is observed. The MOKE loop of as prepared film indicated a squareness ratio of 0.62. As the film is irradiated with fluences of 1×1011 ions/cm2, 1×1012 ions/cm2 and 1×1013 ions/cm2 the squareness ratio changes to 0.76, 0.8 and 0.86 respectively. This enhancement in squareness ratio towards 1 is a typical feature when the exchange interaction starts to dominates the inherent anisotropies in the system. The variation in surface magnetisation is explained based on the variations in surface roughness with swift heavy ion (SHI) irradiation.

  13. Calculation of Production and Decay of Radio Isotopes for Future Irradiation Experiments and Ion Bea

    CERN Document Server

    M. Eller, J. Lettry, R. Catherall, T. Stora

    The design of future radioactive ion beam (RIB) facilities requires the forecast of radio isotope inventory after irradiation. At CERN ISOLDE we developed a software tool that estimates the roduction and activation of materials for ISOLDE radioactive waste anagement. The tool can also be used in the design of new RIB facilities, for licensing procedures, for irradiation experiments and the estimation of production yields.

  14. Investigation of heat release in the targets during irradiation by ion beams

    CERN Document Server

    Dalkarov, O D; Rusetskii, A S

    2015-01-01

    The DD-reaction is investigated and the heat emission off the targets during their irradiation with ion beams is studied at the HELIS ion accelerator at LPI. The heat emission is observed to be significantly higher in the case of irradiation of the Ti/TiO2:Dx-targets by a D+ beam, as compared to the H+ and Ne+ beams. Furthermore, it depends on the concentration of deuterium in the target and current density of the deuteron beam.

  15. Cathodoluminescence and photoluminescence of swift ion irradiation modified zinc oxide-porous silicon nanocomposite

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, Yogesh [CIICAp, UAEM, Av. Univ. 1001, Col. Chamilpa, Cuer., Mor., C.P. 62209 (Mexico); CIMAV, Av. Miguel de Cervantes 120, Compl. Indus. Chih., Chih., C.P. 31109 (Mexico); Herrera, Manuel [CNyN-UNAM, Ensenada Apdo. Postal 14, CP. 22800, Ensenada, B.C. (Mexico); Singh, Fouran [Inter University Accelarator Centre, Aruna Asaf Ali Marg, New Delhi-110067 (India); Olive-Mendez, S.F. [CIMAV, Av. Miguel de Cervantes 120, Compl. Indus. Chih., Chih., C.P. 31109 (Mexico); Kanjilal, D.; Kumar, Shiv [Inter University Accelarator Centre, Aruna Asaf Ali Marg, New Delhi-110067 (India); Agarwal, V., E-mail: vagarwal@uaem.mx [CIICAp, UAEM, Av. Univ. 1001, Col. Chamilpa, Cuer., Mor., C.P. 62209 (Mexico)

    2012-09-20

    We report the room temperature cathodoluminescence and photoluminescence of swift ion irradiated (130 MeV Nickel ion) porous silicon zinc oxide nanocomposites. The evolution of a broad and flat emission band from 1.5 to 3.5 eV is demonstrated. Annealing effect of irradiation is found to result in a relative increase in the band edge emission. Emission wavelength can be tuned in the complete visible range by changing the substrate characteristics.

  16. Application of ion beam irradiated ePTFE to repair small vessel injuries

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, N. [Tokyo University of Science, 1-3 Kagurazaka, Shinjuku, Tokyo 162-8601 (Japan) and Beam Application Team, RIKEN, 2-1 Hirosawa, Wako, Saitama 351-0198 (Japan)]. E-mail: norikichi@ionbeams.riken.jp; Suzuki, Y. [Beam Application Team, RIKEN, 2-1 Hirosawa, Wako, Saitama 351-0198 (Japan); Ujiie, H. [Tokyo Women' s Medical University, 8-1 Kawada-cho, Shinjuku, Tokyo 162-8666 (Japan); Hori, T. [Tokyo Women' s Medical University, 8-1 Kawada-cho, Shinjuku, Tokyo 162-8666 (Japan); Iwaki, M. [Beam Application Team, RIKEN, 2-1 Hirosawa, Wako, Saitama 351-0198 (Japan); Yamada, T. [Tokyo University of Science, 1-3 Kagurazaka, Shinjuku, Tokyo 162-8601 (Japan)

    2007-04-15

    In surgery, bleeding from small injured vessels often requires prompt hemostasis without occlusion. This study evaluated the usefulness of 0.06 mm thick ion beam irradiated ePTFE sheets to repair small holes in vessels. Both surfaces of ePTFE sheets were irradiated with a 150 keV-Ar{sup +} beam with fluences of 5 x 10{sup 14} ions/cm{sup 2}. A small hole up to 2 mm in diameter was created in the common carotid artery of a rabbit. The defect was wrapped with an ion beam irradiated or non-irradiated ePTFE sheet. Fibrin glue was used to fix the ePTFE sheets to the common carotid artery. Hemostasis was instantly obtained with ion beam irradiated ePTFE but was rather difficult when using a non-irradiated ePTFE sheet. Three weeks after implantation, no occlusion was observed. Histological examination showed that the ePTFE sheets functioned as a scaffold for vessel wall regeneration. Thin ion beam irradiated ePTFE would be useful in vascular surgery.

  17. Phase stability in thermally-aged CASS CF8 under heavy ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Li, Meimei, E-mail: mli@anl.gov [Argonne National Laboratory, 9700 S. Cass Avenue, Argonne, IL 60439 (United States); Miller, Michael K. [Oak Ridge National Laboratory, P.O. Box 2008, Oak Ridge, TN 37831 (United States); Chen, Wei-Ying [Argonne National Laboratory, 9700 S. Cass Avenue, Argonne, IL 60439 (United States)

    2015-07-15

    Highlights: • Thermally-aged CF8 was irradiated with 1 MeV Kr ions at 400 °C. • Atom probe tomography revealed a strong dose dependence of G-phase precipitates. • Phase separation of α and α′ in ferrite was reduced after irradiation. - Abstract: The stability of the microstructure of a cast austenitic stainless steel (CASS), before and after heavy ion irradiation, was investigated by atom probe tomography (APT). A CF8 ferrite–austenite duplex alloy was thermally aged at 400 °C for 10,000 h. After this treatment, APT revealed nanometer-sized G-phase precipitates and Fe-rich α and Cr-enriched α′ phase separated regions in the ferrite. The thermally-aged CF8 specimen was irradiated with 1 MeV Kr ions to a fluence of 1.88 × 10{sup 19} ions/m{sup 2} at 400 °C. After irradiation, APT analysis revealed a strong spatial/dose dependence of the G-phase precipitates and the α–α′ spinodal decomposition in the ferrite. For the G-phase precipitates, the number density increased and the mean size decreased with increasing dose, and the particle size distribution changed considerably under irradiation. The inverse coarsening process can be described by recoil resolution. The amplitude of the α–α′ spinodal decomposition in the ferrite was apparently reduced after heavy ion irradiation.

  18. Irradiation damage

    Energy Technology Data Exchange (ETDEWEB)

    Howe, L.M

    2000-07-01

    There is considerable interest in irradiation effects in intermetallic compounds from both the applied and fundamental aspects. Initially, this interest was associated mainly with nuclear reactor programs but it now extends to the fields of ion-beam modification of metals, behaviour of amorphous materials, ion-beam processing of electronic materials, and ion-beam simulations of various kinds. The field of irradiation damage in intermetallic compounds is rapidly expanding, and no attempt will be made in this chapter to cover all of the various aspects. Instead, attention will be focused on some specific areas and, hopefully, through these, some insight will be given into the physical processes involved, the present state of our knowledge, and the challenge of obtaining more comprehensive understanding in the future. The specific areas that will be covered are: point defects in intermetallic compounds; irradiation-enhanced ordering and irradiation-induced disordering of ordered alloys; irradiation-induced amorphization.

  19. Surface Disorder of GaN Irradiated by Highly Charged Arq+-Ions

    Institute of Scientific and Technical Information of China (English)

    ZHANG Li-Qing; ZHANG Chong-Hong; YANG Yi-Tao; YAO Cun-Feng; LI Bing-Sheng; SUN You-Mei; SONG Shu-Jian

    2009-01-01

    The surface damage to gallium nitride films irradiated by Arq+ (6 < q < 16) ions at room temperature is studied by the atomic force microscopy.It is found that when charge state exceeds a threshold value,significant swelling was turned into obvious erosion in the irradiated region.The surface change of the irradiated region strongly depends on the charge state and ion fluence.On the other hand,surface change is less dependent on the kinetic energy nearly in the present experimental range (120keV≤Ek≤220 keV).For q≤14,surface of the irradiated region is covered with an amorphous layer,rough and bulgy.A step-up appears between the irradiated and un-irradiated region. Moreover,the step height and the surface roughness are functions of the ion dose and charge state,and increase with the increase of dose and charge state.Especially at and near boundary,a sharp bump like ridges in irradiated areas is observed,and there appear characteristic grooves in un-irradiated areas.For q=16,surface of the irradiated region was etched and erased.

  20. Mouse skin damages caused by fractionated irradiation with carbon ions

    Energy Technology Data Exchange (ETDEWEB)

    Ando, K.; Chen, Y.J.; Ohira, C.; Nojima, K.; Ando, S.; Kobayashi, N.; Ohbuchi, T.; Shimizu, W. [Space and Particle Radiation Science Research Group, Chiba (Japan); Koike, S.; Kanai, T. [National Inst. of Radiological Sciences, Chiba (Japan). Div. of Accelerator Physics

    1997-09-01

    We have investigated carbon-dose responses of early and late skin damages after daily fractionations to the mouse leg. Depilated legs were irradiated with 7 different positions within 290 MeV/u carbon beams. Fractionation schedules were 1, 2, 4 and 8 daily fractions. Skin reaction was scored every other day for 32 days. Five highest scores in individual mice were averaged, and used as averaged peak reaction. The isoeffect doses to produce an averaged peak skin reaction of 3.0 (moist desquamation) on dose-response curves were calculated with 95% confidence limit. The isoeffect dose for control gamma rays constantly increased with an increase in the number of fraction. The isoeffect doses in low LET carbon ions of 14- and 20 keV/{mu}m also increased up to 4 fractions, but did not increase when 4 fractions increased to 8 fractions. The saturation of isoeffect dose was more prominently observed for 40 keV/{mu}m in such that the isoeffect doses did not change among 2, 4 and 8 fractions. The isoeffect doses for LET higher than 50 keV/{mu}m were smaller than those for lower LET. However, the isoeffect doses for 50-, 60-, 80- and 100 keV/{mu} steadily increased with an increase in the number of fraction and did not show any saturation up to 8 fractions. Relation between LET and RBE was linear for all fractionation schedules. The slope of regression line in 4 fractions was steepest, and significantly (P<0.05) different from that in 1 fraction. (orig.)

  1. Effect of ion beam irradiation on metal particle doped polymer composites

    Indian Academy of Sciences (India)

    N L Singh; Sejal Shah; Anjum Qureshi; A Tripathi; F Singh; D K Avasthi; P M Raole

    2011-02-01

    Polymethyl methacrylate (PMMA) was prepared by solution polymerization method. Different concentrations (10, 20 and 40%) of Ni powder were dispersed in PMMA and the composite films were prepared by casting method. These films were irradiated with 120 MeV Ni$^{10+}$ ions at a fluence of 5 × 1012 ions/cm2. Electrical, structural and chemical properties of the composites were studied by means of an LCR meter, X-ray diffraction, FTIR spectroscopy and SEM/AFM, respectively. The results showed that the conductivity increases with metal concentration and also with ion beam irradiation. This reveals that ion beam irradiation promotes the metal/polymer bonding and converts polymeric structure into hydrogen depleted carbon network. It was observed from XRD analysis that percentage crystallinity and crystalline size decrease upon irradiation. This might be attributed to rupture of some polymeric bonds, which is also corroborated with FTIR spectroscopic analysis. Ion beam tempts graphitization of polymeric material by emission of hydrogen and/or other volatile gases. Surface morphology of the pristine and irradiated films was studied by atomic force microscopy (AFM)/scanning electron microscopy (SEM). Result showed that the surface roughness increases after ion beam irradiation.

  2. Evolutions of Molecular Oxygen Formation and Sodium Migration in Xe Ion Irradiated Borosilicate Glasses

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Liang; Zhang, Duofei F.; Lv, Peng; Zhang, Jiandong; Du, Xing; Yuan, Wei; Nan, Shuai; Zhu, Zihua; Wang, Tieshan

    2016-07-23

    The modifications of a commercial borosilicate glass induced by Xe ion irradiation have been studied by Raman spectroscopy and ToF-SIMS depth profiling. A decrease in the average Si–O–Si angle, an increase in the population of three-membered rings and an increase of the glass polymerization are evidenced. The molecular oxygen appears in the irradiated glasses after the irradiation fluence reaches approximately 1015 ions/cm2. The O2 concentration decreaseswith the depth of irradiated glass at the ion fluence of 2 × 1016 ions/cm2. A sodiumdepleted layer at the surface and a depleted zone at around the penetration depth of 5 MeV Xe ions are observed. The thickness of the sodium depleted layer increases with the irradiation fluence. Moreover, comparing with previous results after electron and Ar ion irradiation, it can be concluded that the nuclear energy deposition can partially inhibit the formation of molecular oxygen and increase the threshold value of electron energy deposition for the molecular oxygen formation.

  3. Electrical properties of irradiated PVA film by using ion/electron beam

    Science.gov (United States)

    Abdelrahman, M. M.; Osman, M.; Hashhash, A.

    2016-02-01

    Ion/electron beam bombardment has shown great potential for improving the surface properties of polymers. Low-energy charged (ion/electron) beam irradiation of polymers is a good technique to modify properties such as electrical conductivity, structural behavior, and their mechanical properties. This paper reports on the effect of nitrogen and electron beam irradiation on the electrical properties of polyvinyl alcohol (PVA) films. PVA films of 4 mm were exposed to a charged (ion/electron) beam for different treatment times (15, 30, and 60 minutes); the beam was produced from a dual beam source using nitrogen gas with the other ion/electron source parameters optimized. The dielectric loss tangent tan δ , electrical conductivity σ , and dielectric constant ɛ ^' } in the frequency range 100 Hz-100 kHz were measured at room temperature. The variation of dielectric constant and loss tangent as a function of frequency was also studied at room temperature. The dielectric constant was found to be strongly dependent on frequency for both ion and electron beam irradiation doses. The real (ɛ ^' }) and imaginary (ɛ ^' ' }) parts of the dielectric constant decreased with frequency for all irradiated and non-irradiated samples. The AC conductivity showed an increase with frequency for all samples under the influence of both ion and electron irradiation for different times. Photoluminescence (PL) spectral changes were also studied. The formation of clusters and defects (which serve as non-radiative centers on the polymer surface) is confirmed by the decrease in the PL intensity.

  4. Ordered arrangement of irradiation-induced defects of polycrystalline tungsten irradiated with low-energy hydrogen ions

    Energy Technology Data Exchange (ETDEWEB)

    Ni, Weiyuan; Yang, Qi; Fan, Hongyu; Liu, Lu [School of Physics and Materials Engineering, Dalian Nationalities University, Dalian 116600 (China); Berthold, Tobias; Benstetter, Günther [Faculty of Electrical Engineering and Media Technology, University of Applied Sciences Deggendorf, Deggendorf 94469 (Germany); Liu, Dongping, E-mail: dongping.liu@dlnu.edu.cn [School of Physics and Materials Engineering, Dalian Nationalities University, Dalian 116600 (China)

    2015-09-15

    Low-energy (20–520 eV) hydrogen ion irradiations were performed at W surface temperature of 373–1073 K and a fluence ranging from 5.0 × 10{sup 23} to 1.0 × 10{sup 25}/m{sup 2}. Conductive atomic force microscopy (CAFM) as a nondestructive analytical technique was successfully used to detect irradiation-induced defects in polycrystalline W. The size and density of these nanometer-sized defects were strongly dependent on the fluence of hydrogen ions. Both ion energy (E) and temperature (T) play a crucial role in determining the ordering of nanometer-sized defects. Ordered arrangements were formed at relatively high E and T. This can be attributed to the stress-driven ripple effect of defect growth at crystal grains, resulting in the movement of W lattice along one certain crystal planes.

  5. Effects of low-dose carbon ion irradiation on the proliferation of splenocytes and the concentration of interferon in mice

    Science.gov (United States)

    Li, Ning

    AIM: To investigate the changes in the proliferation response of splenic lymphocytes and the concentration of serum interferon (IFN-γ) in mice induced by low doses carbon ion irradiation. METHODS: The experiment was carried out in the laboratory of physical medicine, Institute of Modern Physics, Chinese Academy of Sciences in November 2006. 1. Thirty Kunming mice were randomly divided into five groups with six animals in each group and irradiated with 0, 0.01, 0.03, 0.05 and 0.10 Gy carbon ion at Heavy Ion Research Facility Laboratory of Lanzhou. Twenty-four hours after irradiation, the eyeballs of mice were taken out under anesthesia and blood was harvested. 2. The concentration of IFN-γ in serum was detected by ELISA kit. After the mice were executed, the spleen was harvested under sterile condition to prepare spleen mononuclear cell suspension. The effects of concanavalin A(ConA) and lipopolysaccharide(LPS) on the proliferations of mononuclear cells was tested by MTT assay. RESULTS: All thirty mice were involved in the result analysis. 1. The concentration of IFN-γ in serum remarkably increased after irradiation with 0.01 Gy and 0.03 Gy compared with that in controls (p<0.05). However, the concentration of IFN-γ decreased after irradiation with 0.05 Gy and 0.1 Gy. 2. Compared with control group, the proliferation of T lymphocytes induced by ConA and B lymphocytes induced by LPS remarkably increased after irradiation with 0.01 Gy (p<0.001) and the effect was of significant difference compared with that of 0.03 Gy (p<0.01). The irradiation with 0.05 Gy presented an inhibition to the proliferation of splenic lymphocytes. This inhibition was also obvious when irradiated with 0.10 Gy. CONCLUSION: 0.01 Gy and 0.03 Gy carbon ion irradiation can stimulate the proliferation of splenocytes, induce the secretion of IFN-γ and, in consequence, enhance the immune function.

  6. Accumulation of dislocation loops in the α phase of Zr Excel alloy under heavy ion irradiation

    Science.gov (United States)

    Yu, Hongbing; Yao, Zhongwen; Idrees, Yasir; Zhang, He K.; Kirk, Mark A.; Daymond, Mark R.

    2017-08-01

    In-situ heavy ion irradiations were performed on the high Sn content Zr alloy 'Excel', measuring type dislocation loop accumulation up to irradiation damage doses of 10 dpa at a range of temperatures. The high content of Sn, which diffuses slowly, and the thin foil geometry of the sample provide a unique opportunity to study an extreme case where displacement cascades dominate the loop formation and evolution. The dynamic observation of dislocation loop evolution under irradiation at 200 °C reveals that type dislocation loops can form at very low dose (0.0025 dpa). The size of the dislocation loops increases slightly with irradiation damage dose. The mechanism controlling loop growth in this study is different from that in neutron irradiation; in this study, larger dislocation loops can condense directly from the interaction of displacement cascades and the high concentration of point defects in the matrix. The size of the dislocation loop is dependent on the point defect concentration in the matrix. A negative correlation between the irradiation temperature and the dislocation loop size was observed. A comparison between cascade dominated loop evolution (this study), diffusion dominated loop evolution (electron irradiation) and neutron irradiation suggests that heavy ion irradiation alone may not be enough to accurately reproduce neutron irradiation induced loop structures. An alternative method is proposed in this paper. The effects of Sn on the displacement cascades, defect yield, and the diffusion behavior of point defects are established.

  7. Quantitative Assessment of Amino Acid Damage upon keV Ion Beam Irradiation Through FTIR Spectroscopy

    Science.gov (United States)

    Huang, Qing; Ke, Zhigang; Su, Xi; Yuan, Hang; Zhang, Shuqing; Yu, Zengliang

    2010-06-01

    Ion beam irradiation induces important biological effects and it is a long-standing task to acquire both qualitative and quantitative assessment of these effects. One effective way in the investigation is to utilize Fourier transformation infrared (FTIR) spectroscopy because it can offer sensitive and non-invasive measurements. In this paper a novel protocol was employed to prepare biomolecular samples in the form of thin and transversely uniform solid films that were suitable for both infrared and low-energy ion beam irradiation experiments. Under the irradiation of N+ and Ar+ ion beams of 25 keV with fluence ranging from 5×1015 ions/cm2 to 2.5×10 ions/cm2, the ion radio-sensitivity of four amino acids, namely, glycine, tyrosine, methionine and phenylalanine, were evaluated and compared. The ion beam irradiation caused biomolecular decomposition accompanied by molecular desorption of volatile species and the damage was dependent on ion type, fluence, energy and types of amino acids. The effectiveness of application of FTIR spectroscopy to the quantitative assessment of biomolecular damage dose effect induced by low-energy ion radiation was thus demonstrated.

  8. Thermal property of regioregular poly(3-hexylthiophene)/nanotube composites using modified single-walled carbon nanotubes via ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Adhikari, A R [College of Nanoscale Science and Engineering, State University of New York, Albany, NY 12203 (United States); Huang, M [College of Nanoscale Science and Engineering, State University of New York, Albany, NY 12203 (United States); Bakhru, H [College of Nanoscale Science and Engineering, State University of New York, Albany, NY 12203 (United States); Chipara, M [Department of Physics and Geology, University of Texas Pan American, Edinburg, TX 78541-2999 (United States); Ryu, C Y [Department of Chemistry and Chemical Biology, Rensselaer Polytechnic Institute, Troy, NY 12180 (United States); Ajayan, P M [Department of Material Science and Engineering, Rensselaer Polytechnic Institute, Troy and Rensselaer Nanotechnology Center, NY 12180 (United States)

    2006-12-28

    The effects of radiation-induced modifications on the thermal stability and phase transition behaviour of composites made of 1% pristine or ion irradiated single-walled carbon nanotubes (SWNTs) and poly(3-hexylthiophene) (P3HT) are reported. Thermogravimetry analysis (TGA), differential scanning calorimetry (DSC), Raman spectroscopy and electron spin resonance (ESR) were used to investigate the radiation-induced functionalization of carbon nanotubes and to assess the effect of ionizing radiation on the adhesion between macromolecular polymer and carbon nanotubes. Irradiation was used to introduce defects in a controlled way solely within pristine nanotubes before composite synthesis. The addition of irradiated SWNTs to a polymer matrix was found to enhance thermo-oxidative stability and phase transition behaviour. Further, ESR studies demonstrate the electronic interaction through charge transfer between filler and matrix. These results could have immense applications in nanotube composite processing. Based on the experimental data, a model for the interaction between polymeric chains and carbon nanotubes is proposed.

  9. Ion beam irradiation effects in strontium zirconium phosphate with NZP-structure type

    Energy Technology Data Exchange (ETDEWEB)

    Gregg, Daniel J., E-mail: daniel.gregg@ansto.gov.au [Institute of Materials Engineering, Australian Nuclear Science and Technology Organisation, Locked Bag 2001, Kirrawee DC, NSW 2232 (Australia); Karatchevtseva, Inna; Thorogood, Gordon J.; Davis, Joel [Institute of Materials Engineering, Australian Nuclear Science and Technology Organisation, Locked Bag 2001, Kirrawee DC, NSW 2232 (Australia); Bell, Benjamin D.C.; Jackson, Matthew [Department of Materials, Imperial College, London SW7 2BP (United Kingdom); Dayal, Pranesh [Institute of Materials Engineering, Australian Nuclear Science and Technology Organisation, Locked Bag 2001, Kirrawee DC, NSW 2232 (Australia); Ionescu, Mihail [Institute of Environment Science, Australian Nuclear Science and Technology Organisation, Locked Bag 2001, Kirrawee DC, NSW 2232 (Australia); Triani, Gerry; Short, Ken; Lumpkin, Gregory R.; Vance, Eric R. [Institute of Materials Engineering, Australian Nuclear Science and Technology Organisation, Locked Bag 2001, Kirrawee DC, NSW 2232 (Australia)

    2014-03-15

    Ceramics with the sodium zirconium phosphate or NZP type structure have potential as nuclear waste form and inert matrix materials. For both applications the material will be subjected to self-radiation damage from α-decay of the incorporated actinides. In this study, ion-beam irradiation using Au- and He-ions has been used to simulate the consequences of α-decay and the effects of irradiation on the structural and macroscopic properties (density and hardness) have been investigated. Irradiation by Au-ions resulted in a significant volume contraction of ∼7%, a reduction in hardness of ∼30% and a loss in long-range order at fluences above 10{sup 14} Au-ions/cm{sup 2}. In contrast, little effect on the material properties was noted for samples irradiated with He-ions up to a fluence of 10{sup 17} ions/cm{sup 2}. Thermal annealing was investigated for the highest fluence Au-ion irradiated sample and significant decomposition was observed.

  10. Stimulated emission and exciton complex in some insulator crystals irradiated by heavy ions

    Energy Technology Data Exchange (ETDEWEB)

    Kimura, Kazuie E-mail: kkimura@postman.riken.go.jp; Kaneko, Junichi; Sharma, Sumit; Itoh, Noriaki

    1999-06-03

    Excitation-density dependent luminescence, its decay curves, and time-resolved spectra were measured for ion irradiated {alpha}-alumina, RbI and CsCl at various temperatures and with a time resolution of 100 ps. Contrary to the usual results of scintillation research, we found that some insulator crystals show excitation-density enhanced stimulated emission through distant interaction between excited states (excitons) and through photons emitted, and found a new 100 ps-lived luminescence band. The manner of excitation-density and temperature dependence of the luminescence efficiency and decay rate of this new band suggests the formation of the exciton complex and further of the electron-hole plasma.

  11. Phase Transformations in Austenitic 0Cr18Ni10Ti Steel Irradiated with High-Energy Heavy Ions

    CERN Document Server

    Hofmann, A; Semina, V K

    2000-01-01

    Radiation-induced segregation and phase transformations in 0Cr18Ni10Ti steel irradiated with high-energy heavy Ar^{+6} ions at 625^o up to 1 dpa (from 0.01 to 1 dpa) have been studied. It was found that ion irradiation accelerates carbide precipitation and EDX-analysis showed irradiation-induced segregation near grain boundaries.

  12. Evolution of precipitate in nickel-base alloy 718 irradiated with argon ions at elevated temperature

    Science.gov (United States)

    Jin, Shuoxue; Luo, Fengfeng; Ma, Shuli; Chen, Jihong; Li, Tiecheng; Tang, Rui; Guo, Liping

    2013-07-01

    Alloy 718 is a nickel-base superalloy whose strength derives from γ'(Ni3(Al,Ti)) and γ″(Ni3Nb) precipitates. The evolution of the precipitates in alloy 718 irradiated with argon ions at elevated temperature were examined via transmission electron microscopy. Selected-area electron diffraction indicated superlattice spots disappeared after argon ion irradiation, which showing that the ordered structure of the γ' and γ″ precipitates became disordered. The size of the precipitates became smaller with the irradiation dose increasing at 290 °C.

  13. Swift heavy ion irradiated SnO{sub 2} thin film sensor for efficient detection of SO{sub 2} gas

    Energy Technology Data Exchange (ETDEWEB)

    Tyagi, Punit; Sharma, Savita [Department of Physics and Astrophysics, University of Delhi, Delhi 110007 (India); Tomar, Monika [Department of Physics, Miranda House, University of Delhi, Delhi 110007 (India); Singh, Fouran [Inter University Accelerator Center, Aruna Asaf Ali Marg, New Delhi 110067 (India); Gupta, Vinay, E-mail: drguptavinay@gmail.com [Department of Physics and Astrophysics, University of Delhi, Delhi 110007 (India)

    2016-07-15

    Highlights: • Response of Ni{sup 7+} ion irradiated (100 MeV) SnO{sub 2} film have been performed. • Effect of irradiation on the structural and optical properties of SnO{sub 2} film is studied. • A decrease in operating temperature and increased response is seen after irradiation. - Abstract: Gas sensing response studies of the Ni{sup 7+} ion irradiated (100 MeV) and non-irradiated SnO{sub 2} thin film sensor prepared under same conditions have been performed towards SO{sub 2} gas (500 ppm). The effect of irradiation on the structural, surface morphological, optical and gas sensing properties of SnO{sub 2} thin film based sensor have been studied. A significant decrease in operating temperature (from 220 °C to 60 °C) and increased sensing response (from 1.3 to 5.0) is observed for the sample after irradiation. The enhanced sensing response obtained for the irradiated SnO{sub 2} thin film based sensor is attributed to the desired modification in the surface morphology and material properties of SnO{sub 2} thin film by Ni{sup 7+} ions.

  14. Microfabrication on Teflon surface by MeV-proton-microbeam and keV-nitrogen-ion-beam irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Kitamura, Akane, E-mail: ogawa.akane@jaea.go.jp [Department of Advanced Radiation Technology, Takasaki Advanced Radiation Research Institute, Japan Atomic Energy Agency, 1233 Watanuki-machi, Takasaki, Gunma 370-1292 (Japan); Satoh, Takahiro; Koka, Masashi [Department of Advanced Radiation Technology, Takasaki Advanced Radiation Research Institute, Japan Atomic Energy Agency, 1233 Watanuki-machi, Takasaki, Gunma 370-1292 (Japan); Kobayashi, Tomohiro [Advanced Science Institute, RIKEN, 2-1 Hirosawa, Wako-shi, Saitama 350-0198 (Japan); Kamiya, Tomihiro [Department of Advanced Radiation Technology, Takasaki Advanced Radiation Research Institute, Japan Atomic Energy Agency, 1233 Watanuki-machi, Takasaki, Gunma 370-1292 (Japan)

    2013-07-15

    Polytetrafluoroethylene (PTFE) and fluorinated ethylene propylene (FEP) are fluoropolymers that have several desirable technological properties, such as electrical insulation and chemical inertness. Nitrogen ion beam irradiation at high fluence forms dense microprotrusions on PTFE and FEP surfaces. Such unique surface structures are useful in cell culture dishes where cells can attach and spread on top of the protrusions. To enhance this functionality, control of surface morphology is necessary. In this study, we create smooth patterns between micro-protrusions by using focused MeV proton beam scanning and subsequent keV nitrogen ion beam irradiation. As a result, many double bonds (C=C) and oxygen-containing groups were detected by attenuated total reflectance/Fourier infrared spectroscopy, particularly in the smooth areas.

  15. Low Doses of Oxygen Ion Irradiation Cause Acute Damage to Hematopoietic Cells in Mice.

    Directory of Open Access Journals (Sweden)

    Jianhui Chang

    Full Text Available One of the major health risks to astronauts is radiation on long-duration space missions. Space radiation from sun and galactic cosmic rays consists primarily of 85% protons, 14% helium nuclei and 1% high-energy high-charge (HZE particles, such as oxygen (16O, carbon, silicon, and iron ions. HZE particles exhibit dense linear tracks of ionization associated with clustered DNA damage and often high relative biological effectiveness (RBE. Therefore, new knowledge of risks from HZE particle exposures must be obtained. In the present study, we investigated the acute effects of low doses of 16O irradiation on the hematopoietic system. Specifically, we exposed C57BL/6J mice to 0.1, 0.25 and 1.0 Gy whole body 16O (600 MeV/n irradiation and examined the effects on peripheral blood (PB cells, and bone marrow (BM hematopoietic stem cells (HSCs and hematopoietic progenitor cells (HPCs at two weeks after the exposure. The results showed that the numbers of white blood cells, lymphocytes, monocytes, neutrophils and platelets were significantly decreased in PB after exposure to 1.0 Gy, but not to 0.1 or 0.25 Gy. However, both the frequency and number of HPCs and HSCs were reduced in a radiation dose-dependent manner in comparison to un-irradiated controls. Furthermore, HPCs and HSCs from irradiated mice exhibited a significant reduction in clonogenic function determined by the colony-forming and cobblestone area-forming cell assays. These acute adverse effects of 16O irradiation on HSCs coincided with an increased production of reactive oxygen species (ROS, enhanced cell cycle entry of quiescent HSCs, and increased DNA damage. However, none of the 16O exposures induced apoptosis in HSCs. These data suggest that exposure to low doses of 16O irradiation induces acute BM injury in a dose-dependent manner primarily via increasing ROS production, cell cycling, and DNA damage in HSCs. This finding may aid in developing novel strategies in the protection of the

  16. Effect of Ni and Au ion irradiations on structural and optical properties of nanocrystalline Sb-doped SnO{sub 2} thin films

    Energy Technology Data Exchange (ETDEWEB)

    Mir, Feroz A. [University of Kashmir, University Science Instrumentation Centre, Srinagar, J and K (India); Batoo, Khalid Mujasam [King Saud University, King Abdullah Institute for Nanotechnology, Riyadh (Saudi Arabia)

    2016-04-15

    The effect of swift heavy ion irradiations on the structural and optical properties of 6 % Sb-doped SnO{sub 2} thin films deposited on quartz substrate by electron beam evaporation technique is presented. Two ion species Ni and Au with energy 120 MeV and fluence of 1 x 10{sup 13} ion/cm{sup 2} were used. These films were characterized by X-ray diffraction, atomic force microscope, UV-visible and micro-Raman spectroscopy. From structural analysis, these films exhibit tetragonal rutile structure and retain it even after irradiation. The ion irradiations have shown improvement in the structural properties, such as increase in grain size and decrease in the lattice strain. Raman study also indicates enhancement in quality of crystal structure after irradiations. The grain growth after ion interaction is also observed by atomic force microscope study. Further, a variation in optical band gap and reduction in disorder is observed after irradiation. Other parameters such as Urbach tails energy and steepness parameter are obtained from optical data. The overall observed physical properties show a significant improvement after irradiation. A good correspondence between structures with its various properties can be seen. (orig.)

  17. Structural changes induced in silica by ion irradiation observed by IR reflectance spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Saavedra, Rafael [Materiales para Fusión, Laboratorio Nacional de Fusion, CIEMAT, Avda. Complutense 40, 28040 Madrid (Spain); Martin, Piedad, E-mail: piedad.martin@ciemat.es [Materiales para Fusión, Laboratorio Nacional de Fusion, CIEMAT, Avda. Complutense 40, 28040 Madrid (Spain); Jimenez-Rey, David [Materiales para Fusión, Laboratorio Nacional de Fusion, CIEMAT, Avda. Complutense 40, 28040 Madrid (Spain); Centro Micro-Análisis Materiales (CMAM), Universidad Autónoma de Madrid (UAM), 28049 Madrid (Spain); Vila, Rafael [Materiales para Fusión, Laboratorio Nacional de Fusion, CIEMAT, Avda. Complutense 40, 28040 Madrid (Spain)

    2015-10-15

    Highlights: • IR reflection spectroscopy was used to study microstructural changes in silica. • Electronic excitation was the predominant process of energy transfer in this work. • IR reflection spectra of ion and neutron irradiated silica has been compared. • New IR reflection bands related to three-four member rings appear at high ion fluence. • He{sup +} ions are the best suited to reproduce neutron microstructural changes. - Abstract: The structural changes produced by ion irradiation, He{sup +} (2.5 MeV), O{sup 4+} (13.5 MeV), Si{sup 4+} (24.4 MeV), and Cu{sup 7+} (32.6 MeV), in different types of silica (KU1, KS-4V and Infrasil 301) were observed by IR reflection spectroscopy. The IR reflectance spectra were measured between 400 and 1400 cm{sup −1}. Structural bands wavenumber of the three silica grades, irradiated with the same ion and fluence, is independent on OH or impurity content of silica. Modification in the surface structure of the irradiated face of a silica sample was studied monitoring the changes in the wavenumber of fundamental structural bands as function of the ion fluence. Samples irradiated at high ion fluence present a shift of known structural bands and new IR reflection bands around 608 cm{sup −1} and between 920 and 990 cm{sup −1}, corresponding to a new structure. The spectra of neutron irradiated samples at fluences 10{sup 17} and 10{sup 18} n/cm{sup 2} were also measured and compared with ion irradiated samples.

  18. Observations of defect structure evolution in proton and Ni ion irradiated Ni-Cr binary alloys

    Science.gov (United States)

    Briggs, Samuel A.; Barr, Christopher M.; Pakarinen, Janne; Mamivand, Mahmood; Hattar, Khalid; Morgan, Dane D.; Taheri, Mitra; Sridharan, Kumar

    2016-10-01

    Two binary Ni-Cr model alloys with 5 wt% Cr and 18 wt% Cr were irradiated using 2 MeV protons at 400 and 500 °C and 20 MeV Ni4+ ions at 500 °C to investigate microstructural evolution as a function of composition, irradiation temperature, and irradiating ion species. Transmission electron microscopy (TEM) was applied to study irradiation-induced void and faulted Frank loops microstructures. Irradiations at 500 °C were shown to generate decreased densities of larger defects, likely due to increased barriers to defect nucleation as compared to 400 °C irradiations. Heavy ion irradiation resulted in a larger density of smaller voids when compared to proton irradiations, indicating in-cascade clustering of point defects. Cluster dynamics simulations were in good agreement with the experimental findings, suggesting that increases in Cr content lead to an increase in interstitial binding energy, leading to higher densities of smaller dislocation loops in the Ni-18Cr alloy as compared to the Ni-5Cr alloy.

  19. Modification of magnetic anisotropy in metallic glasses using high-energy ion beam irradiation

    Indian Academy of Sciences (India)

    K V Amrute; U R Mhatre; S K Sinha; D C Kothari; R Nagarajan; D Kanjilal

    2002-05-01

    Heavy ion irradiation in the electronic stopping power region induces macroscopic dimensional change in metallic glasses and introduces magnetic anisotropy in some magnetic materials. The present work is on the irradiation study of ferromagnetic metallic glasses, where both dimensional change and modification of magnetic anisotropy are expected. Magnetic anisotropy was measured using Mössbauer spectroscopy of virgin and irradiated Fe40Ni40B20 and Fe40Ni38Mo4B18 metallic glass ribbons. 90 MeV 127I beam was used for the irradiations. Irradiation doses were 5 × 1013 and 7.5 × 1013 ions/cm2. The relative intensity ratios 23 of the second and third lines of the Mössbauer spectra were measured to determine the magnetic anisotropy. The virgin samples of both the materials display in-plane magnetic anisotropy, i.e., the spins are oriented parallel to the ribbon plane. Irradiation is found to cause reduction in magnetic anisotropy. Near-complete randomization of magnetic moments is observed at high irradiation doses. Correlation is found between the residual stresses introduced by ion irradiation and the change in magnetic anisotropy.

  20. A novel way to estimate the nanoindentation hardness of only-irradiated layer and its application to ion irradiated Fe-12Cr alloy

    Science.gov (United States)

    Kim, Hoon-Seop; Lee, Dong-Hyun; Seok, Moo-Young; Zhao, Yakai; Kim, Woo-Jin; Kwon, Dongil; Jin, Hyung-Ha; Kwon, Junhyun; Jang, Jae-il

    2017-04-01

    While nanoindentation is a very useful tool to examine the mechanical properties of ion irradiated materials, there are some issues that should be considered in evaluating the properties of irradiated layer. In this study, in order to properly extract the hardness of only-irradiated layer from nanoindentation data, a new procedure is suggested in consideration of the geometry of indentation-induced plastic zone. By applying the procedure to an ion irradiated Fe-12Cr alloy, the reasonable results were obtained, validating its usefulness in the investigation of practical effect of irradiation on the mechanical behavior of future nuclear materials.

  1. Influence of Oxygen ions irradiation on Polyaniline/Single Walled Carbon Nanotubes nanocomposite

    Science.gov (United States)

    Patil, Harshada K.; Deshmukh, Megha A.; Gaikwad, Sumedh D.; Bodkhe, Gajanan A.; Asokan, K.; Yasuzawa, Mikito; Koinkar, Pankaj; Shirsat, Mahendara D.

    2017-01-01

    Influence of Oxygen ions (100 MeV) irradiation on Polyaniline (PANI)/Single Walled Carbon Nanotubes (SWNTs) nanocomposite was studied in the present investigation. PANI/SWNTs nanocomposite was synthesized by electrochemical Cyclic Voltammetry technique. Nanocomposite was exposed under SHI irradiation of Oxygen (100 MeV) ions for three different fluences such as 1×1010 ions/cm2, 5×1010 ions/cm2 and 1×1011 ions/cm2. The SHI irradiated PANI/SWNTs nanocomposite was investigated by using morphological (AFM), structural (XRD) and spectroscopy (FTIR) characterization. AFM study exhibits effects of SHI irradiation on morphology of the nanocomposite and root mean square roughness of the nanocomposite is observed to be decreased as fluence was increased. The FTIR absorption spectrum exhibits formation of new functional sites with the increase in intensity of absorption peaks, due to SHI irradiation. X-Ray Diffraction studies show a gradual decrease in the crystalline nature of the nanocomposite upon irradiation.

  2. Influence of irradiation spectrum and implanted ions on the amorphization of ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Zinkle, S.J.; Snead, L.L.

    1995-12-31

    Polycrystalline Al2O3, magnesium aluminate spinel (MgAl2O4), MgO, Si3N4, and SiC were irradiated with various ions at 200-450 K, and microstructures were examined following irradiation using cross-section TEM. Amorphization was not observed in any of the irradiated oxide ceramics, despsite damage energy densities up to {similar_to}7 keV/atom (70 displacements per atom). On the other hand, SiC readily amorphized after damage levels of {similar_to}0.4 dpa at room temperature (RT). Si3N4 exhibited intermediate behavior; irradiation with Fe{sup 2+} ions at RT produced amorphization in the implanted ion region after damage levels of {similar_to}1 dpa. However, irradiated regions outside the implanted ion region did not amorphize even after damage levels > 5 dpa. The amorphous layer in the Fe-implanted region of Si3N4 did not appear if the specimen was simultaneoulsy irradiated with 1-MeV He{sup +} ions at RT. By comparison with published results, it is concluded that the implantation of certain chemical species has a pronounced effect on the amorphization threshold dose of all five materials. Intense ionizing radiation inhibits amorphization in Si3N4, but does not appear to significantly influence the amorphization of SiC.

  3. Irradiation effect of different heavy ions and track section on the silkworm Bombyx mori

    Energy Technology Data Exchange (ETDEWEB)

    Tu Zhenli E-mail: tu514@yahoo.co.jp; Kobayashi, Yasuhiko; Kiguchi, Kenji; Watanabe, Hiroshi

    2003-05-01

    In order to compare the irradiation effects of different ions, wandering larvae were whole-body exposed or locally irradiated with 50-MeV {sup 4}He{sup 2+}, 220-MeV {sup 12}C{sup 5+}, and 350-MeV {sup 20}Ne{sup 8+} ions, respectively. For the whole-body-exposed individuals, the survival rates at the cocooning, pupation, and emergence stages all decreased as dose increased, and a range-dependent difference was clearly observed. For local irradiation of ovaries, irradiation effects depend very strongly on the projectile range. In the case of local irradiation of dermal cells by different track sections of heavy ions, the closer the target was to the high-LET section of the track, the more pronounced were the radiation effects. These results indicated that by selectively using ion species and adjusting the irradiation depth to the target, heavy-ion radiosurgery on particular tissues or organs of small experimental animals can be performed more accurately.

  4. Swift heavy ion irradiation induced nanograin formation in CdTe thin films

    Science.gov (United States)

    Survase, Smita; Narayan, Himanshu; Sulania, I.; Thakurdesai, Madhavi

    2016-11-01

    Swift Heavy Ion (SHI) irradiation is a unique technique for nanograin formation through grain fragmentation. Contrary to the generally reported SHI irradiation induced grain growth on CdTe thin films, we report fragmentation leading to nanograin formation. Thermally evaporated polycrystalline CdTe thin films were irradiated with 100 MeV 197Au, 107Ag and 58Ni ions beams up to a fluence of 5 × 1012 ions/cm2. Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM) were carried out for surface analysis before and after irradiation. SEM micrographs indicate that the larger grains in the as-deposited films were fragmented into smaller grains due to irradiation. The extent of fragmentation was found to increase with increasing electronic energy loss (Se). AFM pictures also supported the irradiation induced fragmentation. Structural characterization was done using X-ray Diffraction (XRD) technique. The ion induced strain and dislocation density were calculated from the XRD data. Both the strain and dislocation density were found to increase with increasing Se . The observed grain fragmentation is explained on the basis of a combined effect of strain induced disintegration of grains after the Coulomb explosion, and an 'incomplete' re-crystallization of the molten thermal spikes. Moreover, the optical band gap Eg (1.5 eV for as-deposited film), determined from UV-vis spectroscopy, increased with Se, and possibly because of ion induced strain and defect annealing.

  5. Raman Spectroscopy of Irradiation Effect in Three Carbon Allotropes Induced by Low Energy B Ions

    Institute of Scientific and Technical Information of China (English)

    FU Yun-Chong; JIN Yun-Fan; YAO Cun-Feng; ZHANG Chong-Hong

    2009-01-01

    Irradiation effect in three carbon allotropes C6o, diamond and highly oriented pyrolytic graphite (HOPG) induced by 170 keV B ions, mainly including the process of the damage creation, is investigated by means of Rarnan spectroscopy technique. The differences on irradiation sensitivity and structural stability for C6o, HOPG and diamond are compared. The analysis results indicate that C6o is the most sensitive for B ions irradiation, diamond is the second one and the structure of HOPG is the most stable under B ion irradiation. The damage cross sections σ of C6o, diamond and HOPG deduced from the Raman spectra are 7.78 × 10-15, 6.38 × 10-15 and 1.31 × 10-15 cm-2, respectively.

  6. Production of a thermal stress resistant mutant Euglena gracilis strain using Fe-ion beam irradiation.

    Science.gov (United States)

    Yamada, Koji; Kazama, Yusuke; Mitra, Sharbanee; Marukawa, Yuka; Arashida, Ryo; Abe, Tomoko; Ishikawa, Takahiro; Suzuki, Kengo

    2016-08-01

    Euglena gracilis is a common phytoplankton species, which also has motile flagellate characteristics. Recent research and development has enabled the industrial use of E. gracilis and selective breeding of this species is expected to further expand its application. However, the production of E. gracilis nuclear mutants is difficult because of the robustness of its genome. To establish an efficient mutation induction procedure for E. gracilis, we employed Fe-ion beam irradiation in the RIKEN RI beam factory. A decrease in the survival rate was observed with the increase in irradiation dose, and the upper limit used for E. gracilis selective breeding was around 50 Gy. For a practical trial of Fe-ion irradiation, we conducted a screening to isolate high-temperature-tolerant mutants. The screening yielded mutants that proliferated faster than the wild-type strain at 32 °C. Our results demonstrate the effectiveness of heavy-ion irradiation on E. gracilis selective breeding.

  7. Refractive index changes in amorphous SiO{sub 2} (silica) by swift ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Pena-Rodriguez, O., E-mail: ovidio.pena@uam.es [Centro de Micro-Analisis de Materiales, Universidad Autonoma de Madrid (CMAM-UAM), Cantoblanco, E-28049 Madrid (Spain); Instituto de Optica, Consejo Superior de Investigaciones Cientificas (IO-CSIC), C/ Serrano 121, E-28006 Madrid (Spain); Manzano-Santamaria, J. [Centro de Micro-Analisis de Materiales, Universidad Autonoma de Madrid (CMAM-UAM), Cantoblanco, E-28049 Madrid (Spain); Euratom/CIEMAT Fusion Association, Madrid (Spain); Olivares, J. [Centro de Micro-Analisis de Materiales, Universidad Autonoma de Madrid (CMAM-UAM), Cantoblanco, E-28049 Madrid (Spain); Instituto de Optica, Consejo Superior de Investigaciones Cientificas (IO-CSIC), C/ Serrano 121, E-28006 Madrid (Spain); Rivera, A. [Instituto de Fusion Nuclear, Universidad Politecnica de Madrid, C/ Jose Gutierrez Abascal 2, E-28006 Madrid (Spain); Agullo-Lopez, F. [Centro de Micro-Analisis de Materiales, Universidad Autonoma de Madrid (CMAM-UAM), Cantoblanco, E-28049 Madrid (Spain)

    2012-04-15

    The refractive index changes induced by swift ion-beam irradiation in silica have been measured either by spectroscopic ellipsometry or through the effective indices of the optical modes propagating through the irradiated structure. The optical response has been analyzed by considering an effective homogeneous medium to simulate the nanostructured irradiated system consisting of cylindrical tracks, associated to the ion impacts, embedded into a virgin material. The role of both, irradiation fluence and stopping power, has been investigated. Above a certain electronic stopping power threshold ({approx}2.5 keV/nm), every ion impact creates an axial region around the trajectory with a fixed refractive index (around n = 1.475) corresponding to a certain structural phase that is independent of stopping power. The results have been compared with previous data measured by means of infrared spectroscopy and small-angle X-ray scattering; possible mechanisms and theoretical models are discussed.

  8. Ion microbeam irradiation for radiobiology and radical chemistry: status and prospect

    Energy Technology Data Exchange (ETDEWEB)

    Khodja, H, E-mail: hicham.khodja@cea.fr [CEA, IRAMIS, SIS2M, LEEL, 91191 Gif-sur-Yvette (France); CNRS, UMR 3299, SIS2M, LEEL, 91191 Gif-sur-Yvette (France)

    2011-01-01

    Ion microbeams are commonly used to study local irradiation effects in living cells, as it has been established that ion beam irradiations can lead to deleterious changes in cells that are not struck directly by the microbeam. Such changes, which take place over distances long compared to the size of the irradiation spot and for times long compared to the time of irradiation, are collectively termed radiation-induced bystander effect or RIBE. Free-radical chemistry is frequently invoked to explain the RIBE but no unified model is available at present. Ion microbeams when coupled with advanced methods for observing free radicals are the tools of choice for investigating the chemistry and biological processes governing RIBE.

  9. Effect of ion irradiation on the surface, structural and mechanical properties of brass

    Energy Technology Data Exchange (ETDEWEB)

    Ahmad, Shahbaz; Bashir, Shazia, E-mail: shaziabashir@gcu.edu.pk; Ali, Nisar; Umm-i-Kalsoom,; Yousaf, Daniel; Faizan-ul-Haq,; Naeem, Athar; Ahmad, Riaz; Khlaeeq-ur-Rahman, M.

    2014-04-01

    Highlights: • Brass targets were exposed to carbon ions of energy 2 MeV. • The effect of ion dose has been investigated. • The surface morphology is investigated by SEM analysis. • XRD analysis is performed to reveal structural modification. • Mechanical properties were investigated by tensile testing and microhardness testing. - Abstract: Modifications to the surface, structural and mechanical properties of brass after ion irradiation have been investigated. Brass targets were bombarded by carbon ions of 2 MeV energy from a Pelletron linear accelerator for various fluences ranging from 56 × 10{sup 12} to 26 × 10{sup 13} ions/cm{sup 2}. A scanning electron microscope and X-ray diffractometer were utilized to analyze the surface morphology and crystallographic structure respectively. To explore the mechanical properties e.g., yield stress, ultimate tensile strength and microhardness of irradiated brass, an universal tensile testing machine and Vickers microhardness tester were used. Scanning electron microscopy results revealed an irregular and randomly distributed sputter morphology for a lower ion fluence. With increasing ion fluence, the incoherently shaped structures were transformed into dendritic structures. Nano/micro sized craters and voids, along with the appearance of pits, were observed at the maximum ion fluence. From X-ray diffraction results, no new phases were observed to be formed in the brass upon irradiation. However, a change in the peak intensity and higher and lower angle shifting were observed, which represents the generation of ion-induced defects and stresses. Analyses confirmed modifications in the mechanical properties of irradiated brass. The yield stress, ultimate tensile strength and hardness initially decreased and then increased with increasing ion fluence. The changes in the mechanical properties of irradiated brass are well correlated with surface and crystallographic modifications and are attributed to the generation

  10. Shape manipulation of ion irradiated Ag nanoparticles embedded in lithium niobate

    NARCIS (Netherlands)

    Wolf, S.; Rensberg, J.; Johannes, A.; Thomae, R.; Smit, F.; Neveling, R.; Moodley, M.; Bierschenk, T.; Rodriquez, M.; Afra, B.; Hasan, S.B.; Rockstuhl, C.; Ridgway, M.; Bharuth-Ram, K.; Ronning, C.

    2016-01-01

    Spherical silver nanoparticles were prepared by means of ion beam synthesis in lithium niobate. The embedded nanoparticles were then irradiated with energetic 84Kr and 197Au ions, resulting in different electronic energy losses between 8.1 and 27.5 keV nm−1 in the top layer of the samples. Due to th

  11. Carbon nanotube’s modification by focused ion beam irradiation and its healing strategies

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Zongwei; Xu, Lihua [State Key Laboratory of Precision Measuring Technology and Instruments, Centre of MicroNano Manufacturing Technology, Tianjin University (China); Fang, Fengzhou, E-mail: fzfang@gmail.com [State Key Laboratory of Precision Measuring Technology and Instruments, Centre of MicroNano Manufacturing Technology, Tianjin University (China); Gao, Haifeng; Li, Wanli [State Key Laboratory of Precision Measuring Technology and Instruments, Centre of MicroNano Manufacturing Technology, Tianjin University (China)

    2013-07-15

    Single-walled carbon nanotube (SWNT) clusters’ properties and performance have been studied after irradiated by focused ion beam (FIB) Ga ions and post annealing recovery methods. The SWNT was irradiated by FIB with different energy and different doses ranging from 10{sup 13} to 10{sup 17} ions/cm{sup 2}. Raman spectroscopy results showed that FIB with larger energy or larger ion dose would cause distinct SWNT structure defects. It was also found that scanning electron microscope (SEM) observations would slightly affect the SWNT’s Raman results by electron beam induced carbon deposition. Resulting from the unique reconstruction ability of carbon nanotube’s (CNT’s) network structures, the SWNT’s ion-induced defects can be effectively healed by the post heat annealing from 300 °C to 600 °C for the ion dose less than 10{sup 16} ions/cm{sup 2}. And laser irradiation annealing method also studied to heal the defects in SWNT with 25 mW laser power. Research results would be beneficial for the optimization of the carbon nanotube devices’ functionalizations using FIB Ga ions irradiation.

  12. Irradiation influence on Mylar and Makrofol induced by argon ions in a plasma immersion ion implantation system

    Science.gov (United States)

    Hassan, A.; El-Saftawy, A. A.; Aal, S. A. Abd El; Ghazaly, M. El

    2015-08-01

    Mylar and Makrofol polycarbonate polymers were irradiated by Ar ions in a plasma immersion ion implantation (PIII) system. The surface wettability of both polymers was investigated by employing the contact angle method. The measured contact angles were found to depend on the surface layer properties. Good wetting surfaces were found to depend not only on surface roughness but also on its chemistry that analyzed by Fourier transform infrared (FTIR) spectroscopy. Surfaces topography and roughness was investigated and correlated to their surface energy which studied with the aid of acid-base model for evaluating the improvement of surface wettability after irradiation. PIII improves polymers surface properties efficiently in a controllable way.

  13. Reliability studies on NPN RF power transistors under swift heavy ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Pushpa, N.; Praveen, K.C. [Department of Studies in Physics, University of Mysore, Manasagangotri, Mysore 570 006 (India); Gnana Prakash, A.P., E-mail: gnanaprakash@physics.uni-mysore.ac.in [Department of Studies in Physics, University of Mysore, Manasagangotri, Mysore 570 006 (India); Naik, P.S. [Department of Studies in Physics, University of Mysore, Manasagangotri, Mysore 570 006 (India); Cressler, John D. [School of Electrical and Computer Engineering, Georgia Institute of Technology, Atlanta 30308 (United States); Gupta, S.K. [Technical Physics Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India); Revannasiddaiah, D. [Department of Studies in Physics, University of Mysore, Manasagangotri, Mysore 570 006 (India)

    2012-02-15

    NPN RF power transistors were irradiated with 140 MeV Si{sup 10+} ions, 100 MeV F{sup 8+} ions, 50 MeV Li{sup 3+} ions and Co-60 gamma radiation in the dose range from 100 krad to 100 Mrad. The transistor characteristics are studied before and after irradiation from which the parameters such as Gummel characteristics, excess base current ({Delta}I{sub B} = I{sub Bpost} - I{sub Bpre}), dc current gain (h{sub FE}), transconductance (g{sub m}) and collector-saturation current (I{sub CSat}) are determined. The degradation observed in the electrical characteristics is almost the same for different types of ion irradiated NPN RF power transistors with similar total doses although there is a large difference in the linear energy transfer (LET) of the ions. Further, it was observed more degradation in DC I-V characteristics of ion irradiated devices than the Co-60 gamma irradiated devices for higher doses.

  14. Refractive index dispersion of swift heavy ion irradiated BFO thin films using Surface Plasmon Resonance technique

    Science.gov (United States)

    Paliwal, Ayushi; Sharma, Savita; Tomar, Monika; Singh, Fouran; Gupta, Vinay

    2016-07-01

    Swift heavy ion irradiation (SHI) is an effective technique to induce defects for possible modifications in the material properties. There is growing interest in studying the optical properties of multiferroic BiFeO3 (BFO) thin films for optoelectronic applications. In the present work, BFO thin films were prepared by sol-gel spin coating technique and were irradiated using the 15 UD Pelletron accelerator with 100 MeV Au9+ ions at a fluence of 1 × 1012 ions cm-2. The as-grown films became rough and porous on ion irradiation. Surface Plasmon Resonance (SPR) technique has been identified as a highly sensitive and powerful technique for studying the optical properties of a dielectric material. Optical properties of BFO thin films, before and after irradiation were studied using SPR technique in Otto configuration. Refractive index is found to be decreasing from 2.27 to 2.14 on ion irradiation at a wavelength of 633 nm. Refractive index dispersion of BFO thin film (from 405 nm to 633 nm) before and after ion radiation was examined.

  15. Strain-dependent Damage in Mouse Lung After Carbon Ion Irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Moritake, Takashi [Advanced Radiation Biology Research Program, Research Center for Charged Particle Therapy, National Institute of Radiological Sciences, Chiba (Japan); Proton Medical Research Center, University of Tsukuba, Tsukuba (Japan); Fujita, Hidetoshi; Yanagisawa, Mitsuru; Nakawatari, Miyako; Imadome, Kaori; Nakamura, Etsuko; Iwakawa, Mayumi [Advanced Radiation Biology Research Program, Research Center for Charged Particle Therapy, National Institute of Radiological Sciences, Chiba (Japan); Imai, Takashi, E-mail: imait@nirs.go.jp [Advanced Radiation Biology Research Program, Research Center for Charged Particle Therapy, National Institute of Radiological Sciences, Chiba (Japan)

    2012-09-01

    Purpose: To examine whether inherent factors produce differences in lung morbidity in response to carbon ion (C-ion) irradiation, and to identify the molecules that have a key role in strain-dependent adverse effects in the lung. Methods and Materials: Three strains of female mice (C3H/He Slc, C57BL/6J Jms Slc, and A/J Jms Slc) were locally irradiated in the thorax with either C-ion beams (290 MeV/n, in 6 cm spread-out Bragg peak) or with {sup 137}Cs {gamma}-rays as a reference beam. We performed survival assays and histologic examination of the lung with hematoxylin-eosin and Masson's trichrome staining. In addition, we performed immunohistochemical staining for hyaluronic acid (HA), CD44, and Mac3 and assayed for gene expression. Results: The survival data in mice showed a between-strain variance after C-ion irradiation with 10 Gy. The median survival time of C3H/He was significantly shortened after C-ion irradiation at the higher dose of 12.5 Gy. Histologic examination revealed early-phase hemorrhagic pneumonitis in C3H/He and late-phase focal fibrotic lesions in C57BL/6J after C-ion irradiation with 10 Gy. Pleural effusion was apparent in C57BL/6J and A/J mice, 168 days after C-ion irradiation with 10 Gy. Microarray analysis of irradiated lung tissue in the three mouse strains identified differential expression changes in growth differentiation factor 15 (Gdf15), which regulates macrophage function, and hyaluronan synthase 1 (Has1), which plays a role in HA metabolism. Immunohistochemistry showed that the number of CD44-positive cells, a surrogate marker for HA accumulation, and Mac3-positive cells, a marker for macrophage infiltration in irradiated lung, varied significantly among the three mouse strains during the early phase. Conclusions: This study demonstrated a strain-dependent differential response in mice to C-ion thoracic irradiation. Our findings identified candidate molecules that could be implicated in the between-strain variance to early

  16. Ion irradiation of graphene on Ir(111): From trapping to blistering

    Science.gov (United States)

    Herbig, Charlotte; Åhlgren, E. Harriet; Valerius, Philipp; Schröder, Ulrike A.; Martínez-Galera, Antonio J.; Arman, Mohammad A.; Kotakoski, Jani; Knudsen, Jan; Krasheninnikov, Arkady V.; Michely, Thomas

    Graphene grown epitaxially on Ir(111) is irradiated with low energy noble gas ions and the processes induced by atomic collision and subsequent annealing are analyzed using scanning tunneling microscopy, low energy electron diffraction, X-ray photoelectron diffraction and thermal desorption spectroscopy. Upon room temperature ion irradiation graphene amorphizes and recovers its crystalline structure during annealing. The energetic noble gas projectiles are trapped with surprisingly high efficiency under the graphene cover up to extremely high temperatures beyond 1300K. The energy, angle, and ion species dependence of trapping are quantified. At elevated temperatures the trapped gas forms well developed and highly pressurized blisters under the graphene cover. We use molecular dynamics simulations and ab initio calculations to elucidate the trapping mechanism and its thermal robustness. Similar trapping and blistering are observed after ion irradiation of a single layer of hexagonal boron nitride on Ir(111) and we speculate on the generality of the observed phenomena.

  17. The effect of oxygen on void stability in ion-irradiated steel

    Science.gov (United States)

    Seitzman, Larry E.; Dodd, R. Arthur; Kulcinski, Gerald L.

    1990-07-01

    The effect of oxygen on void stability in an Fe-17Ni-13Cr austenitic ternary alloy has been investigated using 15 MeV nickel-ion irradiation at elevated temperatures and preimplantation of 6 MeV oxygen at room temperature. The nickel irradiation was performed over a temperature range of 550 °C to 650 °C. Utilizing transverse specimen preparation techniques, the irradiated steel was examined by transmission electron microscopy (TEM). As little as 10 appm preimplanted oxygen caused a significant increase in the void number density when the steel was irradiated at 550 °C. A near-surface void-denuded zone occurs in the irradiated steel, while a region depleted of visible voids also occurs in the steel injected with 300 appm oxygen or greater and irradiated at 550 °C.

  18. Effect of ion irradiation on nanoscale TiS2 systems with suppressed Titania phase

    Science.gov (United States)

    Hazarika, Saurabh J.; Mohanta, Dambarudhar; Tripathi, A.; Kanjilal, D.

    2016-10-01

    Titanium disulfide (TiS2), being an important of the transition metal dichalcogenide, (TMDC) family, has drawn numerous interest owing to exhibition of tunable band gap as well as high carrier mobility. In this work, we highlight preparation of TiS2 nanopowder with minimal TiO2 content and also demonstrate modified properties upon swift heavy ion irradiation on TiS2 nanoparticles dispersed PVA films. Different properties of the irradiated samples have been characterized through diffraction, microscopic and spectroscopic techniques. As a result of irradiation, due to agglomeration of particles, the grain size is found to increase. We could also observe a red shift after irradiation with increasing fluence, leading to easy flow of electron from valence to conduction band, which shows that conduction of electrons is more in case of irradiated films compared to the pristine one and thus there may be a possibility of using the irradiated samples in various optoelectronic devices.

  19. 200 keV Xe+ ions irradiation effects on Zr-Ti binary films

    Science.gov (United States)

    Wang, Weipeng; Chai, Maosheng; Feng, Wei; Li, Zhengcao; Zhang, Zhengjun

    2015-05-01

    200 keV Xenon irradiation experiments were performed on magnetron sputtered Zr-Ti films under different doses up to 9 * 1015 ions/cm2. XRD, FE-SEM, AFM, HRTEM, nano-indentation and white light interferometer characterizations were applied to study the structural and mechanical properties modification introduced by the bombardment. Upon Xenon irradiation, structure of film matrix kept stable while the crystallinity of the top surface degraded significantly. Meanwhile, properties of irradiated films such as hardness, modulus and sheet resistance evolved with the same tendency, i.e. increased firstly and decrease with further increasing the irradiation dose. By selective area irradiation, competition between the surface sputtering and swelling was revealed, by which surface defects evolution was highlighted. The micro-defects evolution during Xenon irradiation was believed to be responsible for the macro-properties' modification.

  20. 200 keV Xe{sup +} ions irradiation effects on Zr–Ti binary films

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Weipeng; Chai, Maosheng [Key laboratory of Advanced Materials (MOE), School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Feng, Wei [Division of CEFR Project, China Institute of Atomic Energy, Beijing 102413 (China); Li, Zhengcao [Key laboratory of Advanced Materials (MOE), School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Zhang, Zhengjun, E-mail: zjzhang@tsinghua.edu.cn [Key laboratory of Advanced Materials (MOE), School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China)

    2015-05-01

    200 keV Xenon irradiation experiments were performed on magnetron sputtered Zr–Ti films under different doses up to 9 * 10{sup 15} ions/cm{sup 2}. XRD, FE-SEM, AFM, HRTEM, nano-indentation and white light interferometer characterizations were applied to study the structural and mechanical properties modification introduced by the bombardment. Upon Xenon irradiation, structure of film matrix kept stable while the crystallinity of the top surface degraded significantly. Meanwhile, properties of irradiated films such as hardness, modulus and sheet resistance evolved with the same tendency, i.e. increased firstly and decrease with further increasing the irradiation dose. By selective area irradiation, competition between the surface sputtering and swelling was revealed, by which surface defects evolution was highlighted. The micro-defects evolution during Xenon irradiation was believed to be responsible for the macro-properties’ modification.

  1. Enhanced biological activities of gamma-irradiated persimmon leaf extract.

    Science.gov (United States)

    Cho, Byoung-Ok; Nchang Che, Denis; Yin, Hong-Hua; Jang, Seon-Il

    2017-05-16

    The aim of this study was to compare the anti-oxidative and anti-inflammatory activities of gamma-irradiated persimmon leaf extract (GPLE) with those of non-irradiated persimmon leaf extract (PLE). Ethanolic extract of persimmon leaf was exposed to gamma irradiation at a dose of 10 kGy. After gamma irradiation, the color of the extract changed from dark brown to light brown. The anti-oxidative and anti-inflammatory activities of GPLE and PLE were assessed from: total polyphenol and total flavonoid contents; 2,2-diphenyl-1-picrylhydrazyl (DPPH) assay; 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulphonic acid) (ABTS) assay, and levels of pro-inflammatory mediators such as nitric oxide (NO), prostaglandin E2 (PGE2), tumor necrosis factor alpha (TNF-α) and interleukin-6 (IL-6). The total polyphenol contents of GPLE and PLE were determined to be 224.44 ± 1.54 and 197.33 ± 5.81 mg gallic acid equivalents (GAE)/g, respectively, and the total flavonoid contents of GPLE and PLE were 206.27 ± 1.15 and 167.60 ± 2.00 mg quercetin equivalents (QUE)/g, respectively. The anti-oxidant activities of GPLE and PLE as measured by DPPH assays were 338.33 ± 30.19 μg/ml (IC50) and 388.68 ± 8.45 μg/ml (IC50), respectively, and those measured by ABTS assays were 510.49 ± 15.12 μg/ml (IC50) and 731.30 ± 10.63 μg/ml (IC50), respectively. IC50 is the inhibitor concentration that reduces the response by 50%. GPLE strongly inhibited the production of NO, PGE2 and IL-6 compared with PLE in lipopolysaccharide-stimulated RAW264.7 macrophages. Furthermore, GPLE significantly inhibited the production of TNF-α and IL-6 cytokines compared with PLE in phorbol 12-myristate 13-acetate (PMA) plus A23187-stimulated HMC-1 human mast cells. These results indicate that gamma irradiation of PLE can enhance its anti-oxidative and anti-inflammatory activities through elevation of the phenolic contents. Therefore, gamma-irradiated PLE has potential for use in the food and cosmetic

  2. Erosion yield of metal surface under ion pulsed irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Krivobokov, Valery; Stepanova, Olga, E-mail: omsa@tpu.ru; Yuryeva, Alena

    2013-11-15

    The paper is devoted to the study of erosion processes on a metal surface (Ag, Ni, Cu, W) under argon ion bombardment. The erosion yields including the sputtered and evaporated particles have been calculated for a wide range of the initial ion energy (1–1000 keV). They are revealed to reach the values from units to 10{sup 4} atom/ion under a pulsed ion beam with the power density of 10{sup 2}–10{sup 10} W/cm{sup 2}. The ion beam and target parameters are shown to influence on the erosion intensity.

  3. Damage accumulation in MgO irradiated with MeV Au ions at elevated temperatures

    Science.gov (United States)

    Bachiller-Perea, Diana; Debelle, Aurélien; Thomé, Lionel; Behar, Moni

    2016-09-01

    The damage accumulation process in MgO single crystals under medium-energy heavy ion irradiation (1.2 MeV Au) at fluences up to 4 × 1014 cm-2 has been studied at three different temperatures: 573, 773, and 1073 K. Disorder depth profiles have been determined through the use of the Rutherford backscattering spectrometry in channeling configuration (RBS/C). The analysis of the RBS/C data reveals two steps in the MgO damage process, irrespective of the temperature. However, we find that for increasing irradiation temperature, the damage level decreases and the fluence at which the second step takes place increases. A shift of the damage peak at increasing fluence is observed for the three temperatures, although the position of the peak depends on the temperature. These results can be explained by an enhanced defect mobility which facilitates defect migration and may favor defect annealing. X-ray diffraction reciprocal space maps confirm the results obtained with the RBS/C technique.

  4. Ion irradiation effects on the magnetic anisotropy of Fe thin films

    Energy Technology Data Exchange (ETDEWEB)

    Salazar, Josiane Bueno; Santos, Barbara Canto dos; Geshev, Julian Penkov; Schmidt, Joao Edgar; Schafer, Deise; Grande, Pedro Luis; Pereira, Luis Gustavo [Universidade Federal do Rio Grande do Sul (UFRGS), RS (Brazil). Inst. de Fisica

    2011-07-01

    Full text. The effects of low dimensionality can lead a system to show certain properties quite different from those observed in bulk systems. In general, some of these properties are obtained during manufacturing the sample. However, we may modify them after the deposition by several processes, for example, ion irradiation. In a recent work was observed that Fe thin films grown on Si (111) have a different magnetic behavior depending on the thickness. In our work, we analyzed Fe films with thickness of 60 angstrom and 300 angstrom, which presented the same magnetic characteristics observed previously. Later they were subjected to the irradiation of 20 MeV Au{sup +} ion, in an angle of 45 degrees to the normal of the films. The current density was 4 nA/cm{sup 2} and the fluency was 5 X 10{sup 11} ions/cm{sup 2}. Irradiated films presented an increase in the contribution of shape anisotropy due to the action of the ions. The observation of changes in magnetic behavior and morphological characteristics by ion irradiation was the main motivation for present work. In the present work we discuss the influence of ion irradiation in Fe (60 angstrom) films, whose projection of the beam direction in the plan is presents parallel and perpendicular to the easy axis of magnetization film, performed in an angle of 70 degrees to the normal of the film. We also want to understand the oxidation effects on the magnetic behavior of Fe thin films. This analysis was performed using the MEIS (Medium Energy Ion Scattering) technique, which is also interesting because it provides great accuracy in the study of depth profiles of extremely thin layers. A second work associated with the change effects in the magnetic behavior by ion irradiation is discussed based on samples that present the exchange bias phenomenon

  5. New Ion Beam Materials Laboratory for Materials Modification and Irradiation Effects Research

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Yanwen [ORNL; Crespillo, Miguel L [University of Tennessee (UT); Xue, Haizhou [University of Tennessee, Knoxville (UTK); Jin, Ke [University of Tennessee, Knoxville (UTK); Chen, Chien-Hung [University of Tennessee, Knoxville (UTK); Fontana, Cristiano L [ORNL; Graham, Dr. Joseph T. [The University of Tennessee; Weber, William J [ORNL

    2014-11-01

    A new multifunctional ion beam materials laboratory (IBML) has been established at the University of Tennessee, in partnership with Oak Ridge National Laboratory. The IBML is currently equipped with two ion sources, a 3 MV tandem accelerator, three beamlines and three endstations. The IBML is primarily dedicated to fundamental research on ion-solid interaction, ion beam analysis, ion beam modification, and other basic and applied research on irradiation effects in a wide range of materials. An overview of the IBML facility is provided, and experimental results are reported to demonstrate the specific capabilities.

  6. Time of flight-secondary ion mass spectrometry analysis of protein adsorption on a polyvinylidene difluoride surface modified by ion irradiation.

    Science.gov (United States)

    Okuji, Shigeto; Kitazawa, Hideaki; Takeda, Yoshihiko

    2016-12-01

    We investigated the effects of nanoscopic surface modification of polyvinylidene difluoride (PVDF) and low-density polyethylene (LDPE) by plasma-based ion implantation on protein adsorption with time of flight-secondary ion mass spectrometry (ToF-SIMS) analysis. The chemical composition of the LDPE and PVDF surfaces was changed by ion irradiation. In particular, irradiation substantially decreased the number of CH and CF bonds on the PVDF surface, but only slightly decreased that of CH bonds for LDPE. These decreases may reflect a higher hydrogen recombination rate of the LDPE than the PVDF surface. An increase in oxygen was observed on both the LDPE and PVDF surfaces following ion irradiation, but was saturated after irradiation of 1×10(15)cm(-2) on the PVDF surface. The hydrophilicity of the ion-irradiated LDPE surface was promoted with an increase of the total ion fluence. Ion irradiation also changed the surface properties of PVDF to become more hydrophilic, but the variation did not correlate with the total ion fluence presumably due to the presence of fluorine atoms and the saturation of oxidation. Both bovine serum albumin (BSA) and collagen adsorption were suppressed on the LDPE surface by ion irradiation, which may have resulted from a decrease of the hydrophobic interaction. By contrast, ion irradiation increased protein adsorption on the PVDF surface, and BSA was adsorbed more than collagen, whereas there was no difference in the adsorption between BSA and collagen on the ion-irradiated LDPE surface. Moreover, the adsorption of BSA decreased on the oxygen- and fluorine-rich PVDF surface. These results indicate that the nanoscopic composition changes on the PVDF surface affect the adsorption behavior of BSA. Specifically, ferroelectric property on the PVDF surface was changed by ion irradiation and the nanoscopic change in polarity presumably affected the protein adsorption. Our findings suggest that selective adsorption control of protein can be

  7. Charge-sensitive deep level transient spectroscopy of helium-ion-irradiated silicon, as-irradiated and after thermal annealing

    Institute of Scientific and Technical Information of China (English)

    Li Bing-Sheng; Zhang Chong-Hong; Yang Yi-Tao; Zhou Li-Hong; Zhang Hong-Hua

    2009-01-01

    Electrically active defects in the phosphor-doped single-crystal silicon, induced by helium-ion irradiation under thermal annealing, have been investigated. Isothermal charge-sensitive deep-level transient spectroscopy was employed to study the activation energy and capture cross-section of helium-induced defects in silicon samples. It was shown that the activation energy levels produced by helium-ion irradiation first increased with increasing annealing temperature, with the maximum value of the activation energy occurring at 873 K, and reduced with further increase of the annealing temperature. The energy levels of defects in the samples annealed at 873 and I073 K are found to be located near the mid-forbidden energy gap level so that they can act as thermally stable carrier recombination centres.

  8. Effect of p53 on lung carcinoma cells irradiated by carbon ions or X-rays

    Institute of Scientific and Technical Information of China (English)

    XIE Yi; ZHANG Hong; HAO Jifang; ZHAO Weiping; WU Zhenhua; QIU Rong; WANG Xiaohu

    2009-01-01

    The study is to investigate the feasibility and advantages of heavy ion beams on radiotherapy. The cellular cycle and apoptosis, cell reproductive death and p53 expression evaluated with flow cytometry, clonogenic survival assays and Western blot analysis were examined in lung carcinoma cells after exposure to 89.63 MeV/u carbon ion and 6 MV X-ray irradiations, respectively. The results showed that the number colonyforming assay of A549 was higher than that of H1299 cells in two radiation groups; A549 cellular cycle was arrested in G2/M in 12 h and the per-centage of apoptosis ascended at each time point of carbon ion radiation with doses, the expression of p53 upregulated with doses exposed to X-ray or carbon ion. The cell number in G2/M of H1299 and apoptosis were increasing at all time points with doses in 12C6+ ion irradiation group. The results suggested that the effects of carbon ions or X rays ir-radiation on lung carcinoma cells were different, 12C6+ ion irradiation could have more effect on upregulating the ex-pression of p53 than X-ray, and the upregulated expression of p53 might produce the cellular cycle G2/M arrested, apoptosis increasing; and p53 gene might affect the lung cancer cells radiosensitivity.

  9. Defect induced modification of structural, topographical and magnetic properties of zinc ferrite thin films by swift heavy ion irradiation

    Science.gov (United States)

    Raghavan, Lisha; Joy, P. A.; Vijaykumar, B. Varma; Ramanujan, R. V.; Anantharaman, M. R.

    2017-04-01

    Swift heavy ion irradiation provides unique ways to modify physical and chemical properties of materials. In ferrites, the magnetic properties can change significantly as a result of swift heavy ion irradiation. Zinc ferrite is an antiferromagnet with a Neel temperature of 10 K and exhibits anomalous magnetic properties in the nano regime. Ion irradiation can cause amorphisation of zinc ferrite thin films; thus the role of crystallinity on magnetic properties can be examined. The influence of surface topography in these thin films can also be studied. Zinc ferrite thin films, of thickness 320 nm, prepared by RF sputtering were irradiated with 100 MeV Ag ions. Structural characterization showed amorphisation and subsequent reduction in particle size. The change in magnetic properties due to irradiation was correlated with structural and topographical effects of ion irradiation. A rough estimation of ion track radius is done from the magnetic studies.

  10. Effect of radiation quality on radical formation in ion-irradiated solid alanine

    Energy Technology Data Exchange (ETDEWEB)

    Koizumi, Hitoshi; Ichikawa, Tsuneki; Yoshida, Hiroshi [Hokkaido Univ., Sapporo (Japan); Namba, Hideki; Taguchi, Mitsumasa; Kojima, Takuji

    1997-03-01

    Radical formation in solid alanine irradiated with H{sup +} and He{sup +} ions of 0.5-3.0 MeV and with heavy ions of hundreds of MeV was examined by the ESR method. Radical yield is constant below a critical fluence, and the yield decreases above the fluence. The critical fluence for the H{sup +} and He{sup +} ions is about 10{sup 12} ions cm{sup -2}, while the critical fluence for the heavy ions is 10{sup 10}-10{sup 11} ions cm{sup -2}. G-value of the radical formation (radicals per 100 eV absorbed dose) is obtained from the constant yield at the low fluences. The G-value depends on the radiation quality. This dependence is ascribed to the difference of local dose in the ion tracks. The fluence-yield curves were simulated with a model assuming cylindrical shape of ion tracks and dose-yield relationship for {gamma}-irradiation. This model well explains the fluence-yield curves for the ion irradiations. (author)

  11. Production and stability of dislocation loops in an MgO-Al{sub 2}O{sub 3} system under concurrent irradiation with ions and electrons

    Energy Technology Data Exchange (ETDEWEB)

    Yasuda, Kazuhiro. E-mail: ysktne@mbox.nc.kyushu-u.ac.jp; Kinoshita, Chiken; Ohmura, Masaki; Abe, Hiroaki

    2000-05-02

    In situ microstructure observations have been carried out for crystals of an MgO-Al{sub 2}O{sub 3} system under concurrent irradiation with ions and electrons in a TEM-accelerator facility to gain insights into their concurrent irradiation effects. MgO {center_dot} Al{sub 2}O{sub 3}, MgO {center_dot} 2.4Al{sub 2}O{sub 3} and {alpha}-Al{sub 2}O{sub 3} were irradiated concurrently with 300 keV O{sup +} and 200 keV electrons or solely with 300 keV O{sup +} at 870 K. Retardation of dislocation loop nucleation was observed in MgO {center_dot} Al{sub 2}O{sub 3} and MgO {center_dot} 2.4Al{sub 2}O{sub 3} crystals under the concurrent irradiation, though no significant changes were observed in the microstructure of {alpha}-Al{sub 2}O{sub 3} between regions irradiated concurrently with ions and electrons, and irradiated solely with ions. Further, the concurrent irradiation has been found to enhance the growth of dislocation loops in MgO {center_dot} Al{sub 2}O{sub 3} and MgO {center_dot} 2.4Al{sub 2}O{sub 3} at the periphery of a focused electron beam. The different response in the concurrent irradiation effects among the crystals of MgO-Al{sub 2}O{sub 3} system are discussed in terms of the nucleation rate of dislocation loops under 300 keV O{sup +} irradiation and the stability of loops under electron irradiation, which depend on electron energy and irradiation temperature.

  12. 50 MeV lithium ion beam irradiation effects in poly vinylidene fluoride (PVDF) polymer

    Indian Academy of Sciences (India)

    A K Srivastava; H S Virk

    2000-12-01

    Irradiation effects of 50 MeV 7Li+3 ion beam induced in bulk PVDF polymer have been studied with respect to their optical, chemical, structural and electrical behaviour by using UV-visible, FT-IR spectroscopy, XRD technique and electrical frequency response using LCR bridge. The ion fluences ranging from 1.27 × 1011 to 2.15 × 1013 ions cm–2 have been used to study dose effects of irradiation in PVDF. The recorded UV-visible spectra clearly shows five characteristic peaks at 315, 325, 360, 425 and 600 nm. Due to irradiation, the optical absorption initially decreases but then increases with higher fluences. In the FT-IR spectra, no appreciable change has been observed after irradiation, indicating that this polymer is chemically stable. There is exponential increase in admittance with log of frequency but the effect of irradiation is not quite appreciable. The value of tan and relaxation frequency are changed appreciably due to irradiation. The diffraction pattern of PVDF indicates that this polymer is in semi-crystalline form; a decrease in the crystallinity and crystallite size has been observed due to irradiation.

  13. A mechanistic model for depth-dependent hardness of ion irradiated metals

    Science.gov (United States)

    Xiao, Xiazi; Chen, Qianying; Yang, Hui; Duan, Huiling; Qu, Jianmin

    2017-03-01

    A mechanistic model was developed for modeling the depth-dependent hardness in ion irradiated metallic materials. The model is capable of capturing the indentation size effect, ion irradiation induced damage gradient effect, and effect of unirradiated region acting as a soft substrate. A procedure was developed and described in detail to parametrize the model based on experimentally obtained hardness vs. indentation depth curves. Very good agreement was observed between our model predictions and experimental data of several different stainless steels subjected to various ion irradiation conditions. In addition, two hardening mechanisms are revealed in the new model. One is the well-known indentation size effect arising from the creation of geometrically necessary dislocations as the indenter pierces into the materials. The other is the irradiation hardening due to the presence of irradiation-induced defects. As a function of indentation depth h, the hardening due to indentation size effect is described by hbar∗ / h , while the hardening due to irradiation first follows a power law form Phn , then changes to Z / h - Q /h3 , where hbar∗ , P, n, Z and Q > 0 are constants. This transition occurs at the indentation depth when the plastic zone reaches the end of the irradiated layer.

  14. Effect of swift heavy ion irradiation on dielectrics properties of polymer composite films

    Energy Technology Data Exchange (ETDEWEB)

    Singh, N.L. [Physics Department, M.S. University of Baroda, Vadodara 390002 (India)]. E-mail: singhnl_msu@yahoo.com; Qureshi, Anjum [Physics Department, M.S. University of Baroda, Vadodara 390002 (India)]. E-mail: anjumqur@gmail.com; Singh, F. [Inter University Accelerator Centre, Aruna Asaf Ali Marg, New Delhi 110067 (India); Avasthi, D.K. [Inter University Accelerator Centre, Aruna Asaf Ali Marg, New Delhi 110067 (India)

    2007-02-25

    Ferric oxalate was used as organometallics fillers in polyvinyl chloride (PVC) to form polymer matrix composite films at different concentration of filler. These films were irradiated with 80 MeV O{sup 6+} ions at the fluences of 1 x 10{sup 11} and 1 x 10{sup 12} ions/cm{sup 2}. The radiation induced modifications in dielectric properties, microhardness, surface morphology and surface roughness of polymer composite films have been investigated at different concentration (i.e. 5%, 10% and 15%) of filler. It was observed that hardness and electrical conductivity of the films increase with the concentration of the dispersed ferric oxalate and also with the fluence. From the analysis of frequency, f, dependence of dielectric constant, {epsilon}, it has been found that the dielectric response in both pristine and irradiated samples obey the Universal law given by {epsilon} {proportional_to} f {sup n-1}. The dielectric constant/loss is observed to change significantly due to the irradiation. This suggests that ion beam irradiation promotes (i) the metal to polymer bonding and (ii) convert the polymeric structure into hydrogen depleted carbon network. Thus irradiation makes the polymer harder and more conductive. Atomic force microscopy (AFM) shows that average roughness (R {sub a}) of the irradiated films is lower than that of unirradiated films. Surface morphology of irradiated polymer composite films is observed to change. Scanning electron microscopy (SEM) results show that partial agglomeration of fillers in the polymer matrix.

  15. Post-irradiation effect of Deuterium ion beam onto Rh/W/Cu multilayer thin film

    Energy Technology Data Exchange (ETDEWEB)

    Mostako, A.T.T. [Department of Physics, Indian Institute of Technology Guwahati, Guwahati 781039 (India); Khare, Alika, E-mail: alika@iitg.ernet.in [Department of Physics, Indian Institute of Technology Guwahati, Guwahati 781039 (India); Rao, C.V.S.; Vala, Sudhirsinh; Basu, T.K.; Raole, Prakash M.; Makwana, Rajinikant [Institute for Plasma Research, Bhat, Gandhinagar 382428 (India)

    2014-03-15

    Graphical abstract: AFM images of M{sub 1} and M{sub 2} Rh/W/Cu multilayer samples are in Fig. (a and b) before D ion beam irradiation and that of after 20 keV and 30 keV D ion beam irradiation are in Fig. (c and d), respectively. The columnar structures observed in the AFM images before and after irradiation were intact. The RMS roughness of the films increased by ∼4 nm due to 20 keV and ∼3 nm due to 30 keV D ion beam irradiation. Display Omitted -- Abstract: The fabrication of mirror like multilayer Rh/W/Cu thin films via Pulsed Laser Deposition technique is reported in this paper. These multilayer thin film mirrors were irradiated to 10, 20 and 30 keV energy of Deuterium ion beam. The post-irradiation effects onto the quality of these thin films were investigated by subjecting them to X-ray Diffractometer, Scanning Electron Microscope, Atomic Force Microscope, Ultraviolet (UV)–Visible and Far Infrared (FIR) spectrometer.

  16. Heavy-ion irradiation of pyrochlore oxides: Comparison between low and high energy regimes

    Science.gov (United States)

    Sattonnay, G.; Moll, S.; Thomé, L.; Legros, C.; Herbst-Ghysel, M.; Garrido, F.; Costantini, J.-M.; Trautmann, C.

    2008-06-01

    Pyrochlore pellets with Gd2(Ti2-xZrx)O7 stoichiometry were irradiated with heavy ions at energies ranging from a few MeV to a few GeV in order to compare the effects of nuclear collisions and electronic excitations. The damage created by irradiation was characterized as a function of the ion fluence by X-ray diffraction. The structural modifications induced by irradiation were shown to depend on both the sample composition and the type of irradiation. At low energy (4 MeV Au ions), the susceptibility to radiation-induced amorphization exhibits a systematic decrease with increasing Zr content. At high energy (1.5 GeV Xe or 2.6 GeV U ions), similar structural changes are observed at much lower fluences. The lattice parameter increases for low energy irradiation, particularly in the case of amorphizable pyrochlores (Gd2Ti2O7 and Gd2TiZrO7), whereas it decreases for high energy irradiation.

  17. Swift heavy ion irradiation of metal containing tetrahedral amorphous carbon films

    Energy Technology Data Exchange (ETDEWEB)

    Karaseov, P.A., E-mail: platon.karaseov@spbstu.ru [Peter the Great St. Petersburg Polytechnic University, St. Petersburg (Russian Federation); Protopopova, V.S. [Aalto University, Espoo (Finland); Karabeshkin, K.V.; Shubina, E.N.; Mishin, M.V. [Peter the Great St. Petersburg Polytechnic University, St. Petersburg (Russian Federation); Koskinen, J. [Aalto University, Espoo (Finland); Mohapatra, S. [Guru Gobind Singh Indraprastha University, New Delhi (India); Tripathi, A. [Inter University Accelerator Center, New Delhi (India); Avasthi, D.K. [Amity University, Noida 201313, Uttar Pradesh (India); Titov, A.I. [Peter the Great St. Petersburg Polytechnic University, St. Petersburg (Russian Federation)

    2016-07-15

    Highlights: • ta-C films with Ni and Cu doping were grown using dual cathode filtered vacuum arc deposition. • Conductive channels were found in the films by C-AFM after irradiation with 100 MeV Ag ions. • SEM contrast found after irradiation strongly depends on kind of metal impurity in the film. • Different chemical effect of Ni and Cu on transformation of carbon matrix under irradiation was revealed. - Abstract: Thin carbon films were grown at room temperature on (0 0 1) n-Si substrate using dual cathode filtered vacuum arc deposition system. Graphite was used as a source of carbon atoms and separate metallic electrode was simultaneously utilized to introduce Ni or Cu atoms. Films were irradiated by 100 MeV Ag{sup 7+} ions to fluences in the range 1 × 10{sup 10}–3 × 10{sup 11} cm{sup −2}. Rutherford backscattering spectroscopy, Raman scattering, scanning electron microscopy and atomic force microscopy in conductive mode were used to investigate film properties and structure change under irradiation. Some conductive channels having metallic conductivity type were found in the films. Number of such channels is less than number of impinged ions. Presence of Ni and Cu atoms increases conductivity of those conductive channels. Fluence dependence of all properties studied suggests different mechanisms of swift heavy ion irradiation-induced transformation of carbon matrix due to different chemical effect of nickel and copper atoms.

  18. Damages in ceramics for nuclear waste transmutation by irradiation with swift heavy ions

    Science.gov (United States)

    Beauvy, Michel; Dalmasso, Chrystelle; Thiriet-Dodane, Catherine; Simeone, David; Gosset, Dominique

    2006-01-01

    Inert matrices are proposed for advanced nuclear fuels or for the transmutation of the actinides that is an effective solution for the nuclear waste management. The behaviour of inert matrix ceramics like MgO, MgAl2O4 and cubic ZrO2 oxides under irradiation is presented in this study. The alumina Al2O3 has been also studied as a reference for the ceramic materials. These oxides have been irradiated with swift heavy ions at CIRIL/GANIL to simulate the fragment fission effects. The irradiations with the different heavy ions (from S to Pb) with energy between 91 and 820 MeV, have been realised at room temperature or 500 °C. The fluencies were between 5 × 1010 and 5 × 1015 ions/cm2. The polished faces of sintered polycrystalline disks or single crystal slices have been characterized before and after irradiation by X-ray diffraction and optical spectroscopy. The apparent swelling evaluated from surface profile measurements after irradiation is very important for spinel and zirconia, comparatively with those of magnesia or alumina. The amorphisation seems to be at the origin of this swelling, and the electronic stopping power of the ions is the most influent parameter for the irradiation damages. The point defects characterized by optical spectroscopy show a significant amount of damage on the oxygen sub-lattice in the irradiated oxides. F+ centres are present in all irradiated oxides. However, new absorption bands are observed and cation clusters cannot be excluded in magnesia and spinel after irradiation.

  19. Enhanced triboelectrification of the polydimethylsiloxane surface by ultraviolet irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jong Hun; Park, Jeong Young, E-mail: jhjung@inha.ac.kr, E-mail: jeongypark@kaist.ac.kr [Center for Nanomaterials and Chemical Reactions, Institute for Basic Science (IBS), Daejeon 305-701 (Korea, Republic of); Graduate School of EEWS, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 305-701 (Korea, Republic of); Yun, Byung Kil; Jung, Jong Hoon, E-mail: jhjung@inha.ac.kr, E-mail: jeongypark@kaist.ac.kr [Department of Physics, Inha University, Incheon 402-751 (Korea, Republic of)

    2016-03-28

    Study of the triboelectric charging effect has recently gained much attraction by proposing a new potential technical application in the field of energy harvesting. Transparent polydimethylsiloxane (PDMS) has some advantages in employing the triboelectric effect due to good conformity at nanometer scale and the simple fabrication process. In this study, we demonstrate that UV irradiation can enhance the performance of a PDMS-based nanotribogenerator. Contact atomic force microscopy combined with Kelvin probe force microscopy enables an in-depth investigation of the effect of UV illumination on local triboelectric charge generation and its decay in PDMS. We found that UV exposure not only facilitates triboelectric charge generation but also enhances charge redistribution, which is related to the wettability of the PDMS surface. This study provides insights into the fundamental understanding and design of triboelectric generator devices.

  20. Effects of Ion Irradiation on Seedlings Growth Monitored by Ultraweak Delayed Luminescence

    Science.gov (United States)

    Abe, Tomoko; Cirrone, Giuseppe A. P.; Cuttone, Giacomo; Gulino, Marisa; Musumeci, Francesco; Romano, Francesco; Ryuto, Hiromichi; Scordino, Agata

    2016-01-01

    The optical technique based on the measurement of delayed luminescence emitted from the biological samples has demonstrated its ability to provide valid and predictive information on the functional status of various biological systems. We want to extend this technique to study the effect of ionizing radiation on biological systems. In particular we are interested in the action of ion beams, used for therapeutic purposes or to increase the biological diversity. In general, the assessment of the damage that radiation produces both in the target objects and in the surrounding tissues, requires considerable time because is based on biochemical analysis or on the examination of the evolution of the irradiated systems. The delayed luminescence technique could help to simplify this investigation. We have so started our studies performing irradiations of some relatively simple vegetable models. In this paper we report results obtained from mung bean (Vigna radiata) seeds submitted to a 12C ion beam at the energy of 62 MeV/nucleon. The dry seeds were irradiated at doses from 50 to 7000 Gy. The photoinduced delayed luminescence of each seed before and after ion irradiation was measured. The growth of seedlings after irradiation was compared with that of untreated seeds. A growth reduction on increasing the dose was registered. The results show strong correlations between the ion irradiation dose, seeds growth and delayed luminescence intensity. In particular, the delayed luminescence intensity is correlated by a logistic function to the seedlings elongation and, after performing a suitable measurement campaign based on blind tests, it could become a tool able to predict the growth of seeds after ion irradiation. Moreover these results demonstrate that measurements of delayed luminescence could be used as a fast and non-invasive technique to check the effects of ion beams on relatively simple biological systems. PMID:27936220

  1. Morphological and biochemical responses of Oryza sativa L. (cultivar MR219) to ion beam irradiation

    Institute of Scientific and Technical Information of China (English)

    Anna Pick Kiong LING; Ying Chian UNG; Sobri HUSSEIN; Abdul Rahim HARUN; Atsushi TANAKA; Hase YOSHIHIRO

    2013-01-01

    Objective:Heavy ion beam, which has emerged as a new mutagen in the mutation breeding of crops and ornamental plants, is expected to result in the induction of novel mutations. This study investigates the morphological and biochemical responses of Oryza sativa toward different doses of carbon ion beam irradiation. Methods: In this study, the dry seeds of O. sativa were irradiated at 0, 20, 40, 60, 80, 100, and 120 Gy, fol owed by in-vitro germination under control ed conditions. Morphological and biochemical studies were conducted to investigate the morphological and physiological responses of O. sativa towards ion beam irradiation. Results: The study demonstrated that low doses (10 Gy) of ion beam have a stimulating effect on the height, root length, and fresh weight of the plantlets but not on the number of leaves. Meanwhile, doses higher than 10 Gy caused reductions in all the morphological parameters studied as compared to the control samples. The highest total soluble protein content [(2.11±0.47) mg/g FW] was observed in plantlets irradiated at 20 Gy. All irradiated plantlets were found to have 0.85%to 58.32%higher specific activity of peroxidase as compared to the control samples. The present study also revealed that low doses of ion beam (10 and 20 Gy) had negligible effect on the total chlorophyl content of O. sativa plantlets while 40 Gy had a stimulating effect on the chlorophyll content. Plantlets irradiated between 40 to 120 Gy were shown to be 0.38%to 9.98%higher in total soluble nitrogen content which, however, was not significantly different from the control samples. Conclusions:Carbon ion beam irradiation administered at low to moderate doses of 10 to 40 Gy may induce O. sativa mutants with superior characteristics.

  2. Morphological and biochemical responses of Oryza sativa L. (cultivar MR219) to ion beam irradiation*

    Science.gov (United States)

    Ling, Anna Pick Kiong; Ung, Ying Chian; Hussein, Sobri; Harun, Abdul Rahim; Tanaka, Atsushi; Yoshihiro, Hase

    2013-01-01

    Objective: Heavy ion beam, which has emerged as a new mutagen in the mutation breeding of crops and ornamental plants, is expected to result in the induction of novel mutations. This study investigates the morphological and biochemical responses of Oryza sativa toward different doses of carbon ion beam irradiation. Methods: In this study, the dry seeds of O. sativa were irradiated at 0, 20, 40, 60, 80, 100, and 120 Gy, followed by in-vitro germination under controlled conditions. Morphological and biochemical studies were conducted to investigate the morphological and physiological responses of O. sativa towards ion beam irradiation. Results: The study demonstrated that low doses (10 Gy) of ion beam have a stimulating effect on the height, root length, and fresh weight of the plantlets but not on the number of leaves. Meanwhile, doses higher than 10 Gy caused reductions in all the morphological parameters studied as compared to the control samples. The highest total soluble protein content [(2.11±0.47) mg/g FW] was observed in plantlets irradiated at 20 Gy. All irradiated plantlets were found to have 0.85% to 58.32% higher specific activity of peroxidase as compared to the control samples. The present study also revealed that low doses of ion beam (10 and 20 Gy) had negligible effect on the total chlorophyll content of O. sativa plantlets while 40 Gy had a stimulating effect on the chlorophyll content. Plantlets irradiated between 40 to 120 Gy were shown to be 0.38% to 9.98% higher in total soluble nitrogen content which, however, was not significantly different from the control samples. Conclusions: Carbon ion beam irradiation administered at low to moderate doses of 10 to 40 Gy may induce O. sativa mutants with superior characteristics. PMID:24302713

  3. Influence of irradiation spectrum and implanted ions on the amorphization of ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Zinkle, S.J.; Snead, L.L. [Oak Ridge National Laboratory, TN (United States)

    1996-04-01

    Amorphization cannot be tolerated in ceramics proposed for fusion energy applications due to the accompanying large volume change ({approx} 15% in SiC) and loss of strength. Ion beam irradiations at temperatures between 200 K and 450 K were used to examine the likelihood of amorphization in ceramics being considered for the structure (SiC) and numerous diagnostic and plasma heating systems (MgAl{sub 2}O{sub 4}, Al{sub 2}O{sub 3}, MgO, Si{sub 3}N{sub 4}) in fusion energy systems. The microstructures were examined following irradiation using cross-section transmission electron microscopy. The materials in this study included ceramics with predominantly covalent bonding (SiC, Si{sub 3}N{sub 4}) and predominantely ionic bonding (MgAl{sub 2}O{sub 4}, Al{sub 2}O{sub 3}, MgO). The samples were irradiated with a variety of ion beams (including some simultaneous dual ion beam irradiations) in order to investigate possible irradiation spectrum effects. The ion energies were >0.5 MeV in all cases, so that the displacement damage effects could be examined in regions well separated from the implanted ion region.

  4. The conductivity of high-fluence noble gas ion irradiated CVD polycrystalline diamond

    Science.gov (United States)

    Borisov, A. M.; Kazakov, V. A.; Mashkova, E. S.; Ovchinnikov, M. A.; Shemukhin, A. A.; Sigalaev, S. K.

    2017-09-01

    The conductivity of surface layer of polycrystalline CVD (Chemical Vapor Deposition) diamond has been studied experimentally after high-fluence 30 keV Ne+, 20 and 30 keV Ar+ ion irradiation at target temperature range from 30 to 400 °C. The hot ion irradiation of CVD diamond may be described as ion-stimulated heat graphitization in which an exponential resistance decrease with increasing of the irradiation temperature is much faster than at the heat treatment. Under ion irradiation of CVD diamond the graphite-like materials resistivity is achieved at temperatures not exceeding 200 °C. The graphite phase in a heterogeneous structure of diamond irradiated layer is in dynamic equilibrium. In the temperature range from RT to 400 °C, the proportion of graphite phase increases so that at temperatures 200 < Tir < 400 °C it is dominant. The Raman spectra of ion-induced conductive layer created on CVD diamond reflect the processes of nanostructural ordering - disordering of sp2-bonded carbon.

  5. A molecular dynamics analysis of ion irradiation of ultrathin amorphous carbon films

    Science.gov (United States)

    Qi, J.; Komvopoulos, K.

    2016-09-01

    Molecular dynamics (MD) simulations provide insight into nanoscale problems where continuum description breaks down, such as the modeling of ultrathin films. Amorphous carbon (a-C) films are commonly used as protective overcoats in various contemporary technologies, including microelectromechanical systems, bio-implantable devices, optical lenses, and hard-disk drives. In all of these technologies, the protective a-C film must be continuous and very thin. For example, to achieve high storage densities (e.g., on the order of 1 Tb/in.2) in magnetic recording, the thickness of the a-C film used to protect the magnetic media and the recording head against mechanical wear and corrosion must be 2-3 nm. Inert ion irradiation is an effective post-deposition method for reducing the film thickness, while preserving the mechanical and chemical characteristics. In this study, MD simulations of Ar+ ion irradiated a-C films were performed to elucidate the effects of the ion incidence angle and ion kinetic energy on the film thickness and structure. The MD results reveal that the film etching rate exhibits a strong dependence on the ion kinetic energy and ion incidence angle, with a maximum etching rate corresponding to an ion incidence angle of ˜20°. It is also shown that Ar+ ion irradiation mainly affects the structure of the upper half of the ultrathin a-C film and that carbon atom hybridization is a strong function of the ion kinetic energy and ion incidence angle. The results of this study elucidate the effects of important ion irradiation parameters on the structure and thickness of ultrathin films and provide fundamental insight into the physics of dry etching.

  6. Spectroscopic study of energetic helium-ion irradiation effects on nuclear graphite tiles

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Do Wan; Lee, K.W. [Department of Physics, Korea University, Seoul 136-713 (Korea, Republic of); Choi, D.M.; Noh, S.J.; Kim, H.S. [Department of Applied Physics, Dankook University, Yongin 448-701 (Korea, Republic of); Lee, Cheol Eui, E-mail: rscel@korea.ac.kr [Department of Physics, Korea University, Seoul 136-713 (Korea, Republic of)

    2016-02-01

    Highlights: • Energetic helium-ion irradiation on nuclear graphite tiles studied for plasma facing components. • XPS reveals recrystallization at low dose irradiation and DLC sites at higher doses. • Raman spectroscopy reveals increasing diamond-like defects and structural deformation. • Average inter-defect distance obtained as a function of irradiation dose from Raman intensities. - Abstract: Helium ion-irradiation effects on the nuclear graphite tiles were studied in order to understand the structural modifications and damages that can be produced by fusion reaction in tokamaks. The surface morphological changes due to increasing dose of the irradiation were examined by the field-effect scanning electron microscopy, and X-ray photoelectron spectroscopy elucidated the changes in the shallow surface bonding configurations caused by the energetic irradiation. Raman spectroscopy revealed the structural defects and diamond-like carbon sites that increased with increasing irradiation dose, and the average inter-defect distance was found from the Raman peak intensities as a function of the irradiation dose.

  7. Yield of OH radicals in water under heavy ion irradiation. Dependence on mass, specific energy, and elapsed time

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Dependence of yields of OH (hydroxyl) radicals on the mass and specific energy of heavy ions and elapsed time after irradiation was investigated, to understand chemical reactions of aqueous solutions. The yields of irradiation products of phenol, super-linearly increased with the incident energy of He, C, and Ne ions ranging from 2 to 18 MeV/u. The yields of the OH radicals were estimated by analyzing the yields of the irradiation products of phenol.The yields of the OH radicals increased with the specific energy for each ion, but decreased both with the mass of each ion at the same specific energy and elapsed time after irradiation.

  8. Characterization of biodegradable polymers irradiated with swift heavy ions

    Energy Technology Data Exchange (ETDEWEB)

    Salguero, N.G. [Gerencia de Investigacion y Aplicaciones, TANDAR-CNEA, Av. Gral. Paz 1499 (B1650KNA) San Martin, Buenos Aires (Argentina); Grosso, M.F. del, E-mail: delgrosso@tandar.cnea.gov.ar [Gerencia de Investigacion y Aplicaciones, TANDAR-CNEA, Av. Gral. Paz 1499 (B1650KNA) San Martin, Buenos Aires (Argentina); CONICET, Av. Rivadavia 1917 C1033AAJ CABA (Argentina); Duran, H. [CONICET, Av. Rivadavia 1917 C1033AAJ CABA (Argentina); Gerencia de Desarrollo Tecnologico y Proyectos Especiales, CNEA, Av. Gral. Paz 1499 (B1650KNA) San Mart Latin-Small-Letter-Dotless-I Acute-Accent n, Buenos Aires (Argentina); Escuela de Ciencia y Tecnologia, H. Yrigoyen 3100, CP 1650, San Martin, UNSAM (Argentina); Peruzzo, P.J. [CICPBA - Grupo de Materiales y Nanomateriales Polimericos, Instituto de Investigaciones Fisicoquimicas Teoricas y Aplicadas (INIFTA), CCT La Plata CONICET - Universidad Nacional de La Plata, La Plata (Argentina); Amalvy, J.I. [CICPBA - Grupo de Materiales y Nanomateriales Polimericos, Instituto de Investigaciones Fisicoquimicas Teoricas y Aplicadas (INIFTA), CCT La Plata CONICET - Universidad Nacional de La Plata, La Plata (Argentina); Facultad de Ingenieria, Universidad Nacional de La Plata, Calle 116 y 48 (B1900TAG), La Plata (Argentina); Departamento de Ingenieria Quimica, Facultad Regional La Plata, Universidad Tecnologica Nacional, 60 y 124 (1900), La Plata (Argentina); and others

    2012-02-15

    In view of their application as biomaterials, there is an increasing interest in developing new methods to induce controlled cell adhesion onto polymeric materials. The critical step in all these methods involves the modification of polymer surfaces, to induce cell adhesion, without changing theirs degradation and biocompatibility properties. In this work two biodegradable polymers, polyhydroxybutyrate (PHB) and poly-L-lactide acid (PLLA) were irradiated using carbon and sulfur beams with different energies and fluences. Pristine and irradiated samples were degradated by immersion in a phosphate buffer at pH 7.0 and then characterized. The analysis after irradiation and degradation showed a decrease in the contact angle values and changes in their crystallinity properties.

  9. Ion beam damage assessment and waveguide formation induced by energetic Si-ion irradiation in lanthanum aluminate crystal

    Science.gov (United States)

    Liu, Y.; Huang, Q.; Crespillo, M. L.; Qiao, M.; Liu, P.; Wang, X. L.

    2017-02-01

    Lanthanum aluminate (LaAlO3) crystal has emerged as one of the most valuable functional-materials, and its physical, electronic and optical properties strongly depend on the crystal structure, which can be easily altered in an irradiation environment and therefore affect the performance of LaAlO3-based devices. On the other hand, the preparation of LaAlO3 waveguide is also a scientific challenge for its potential application prospects in optoelectronics field. In this work, the damage evolution behavior of LaAlO3 crystal under Si-ion irradiation has been discussed in detail utilizing complementary characterization techniques, and then, single-mode waveguide of LaAlO3 crystal in the visible band can be obtained based on ion-irradiation-induced lattice damage behavior. Waveguide optical-coupling techniques are used to show its competitive features. Thus, novel optical waveguides with optimized features in LaAlO3 crystals can be tailored by a proper selection of ion mass, energy and fluence using the modification of the target material during ion irradiation process.

  10. Influence of 120 MeV Au+9 ions irradiation on resistive switching properties of Cr:SrZrO3/SRO junctions

    Science.gov (United States)

    Bhavsar, Komal H.; Joshi, Utpal S.

    2016-07-01

    Swift heavy ion (SHI) irradiation has been successfully used to modify structural and electrical properties of heterostructured Cr doped SrZrO3 thin films grown on 200 nm thick SrRuO3/SiO2 by chemical solution deposition method. Samples were irradiated by 120 MeV Au+9 ions with fluence value 1 × 1012 ions/cm2 in order to investigate the influence of SHI irradiation on the resistive switching (RS) phenomenon. Structural characterization with grazing angle X-ray diffraction exhibited an enhancement of crystallinity as well as crystallographic strain. Typical energy dispersive analysis of X-rays (EDAX) spectrum was carried out to study the interface mixing, if any, after the ion irradiation. The pristine sample exhibits a narrow hysteresis loop in the current voltage (I-V) curves with maximum RS ratio of 98. Highly reproducible resistive switching characteristics with pronounced loops in the I-V curves have been observed for the irradiated Ag/Cr:SZO/SRO structure with maximum RS ratio of 985. I-V curves in low resistive state (LRS) demonstrate linear Ohmic conduction mechanism for both positive as well as negative bias region. The high resistive state (HRS) is consistent with space charge limited (SCLC) mechanism. The observed electrical behavior can be attributed to the high energy density of electronic excitations resulting from the impact of swift heavy ions induced defects and strain.

  11. Influence of 120 MeV Au{sup +9} ions irradiation on resistive switching properties of Cr:SrZrO{sub 3}/SRO junctions

    Energy Technology Data Exchange (ETDEWEB)

    Bhavsar, Komal H.; Joshi, Utpal S., E-mail: usjoshi@gmail.com

    2016-07-15

    Swift heavy ion (SHI) irradiation has been successfully used to modify structural and electrical properties of heterostructured Cr doped SrZrO{sub 3} thin films grown on 200 nm thick SrRuO{sub 3}/SiO{sub 2} by chemical solution deposition method. Samples were irradiated by 120 MeV Au{sup +9} ions with fluence value 1 × 10{sup 12} ions/cm{sup 2} in order to investigate the influence of SHI irradiation on the resistive switching (RS) phenomenon. Structural characterization with grazing angle X-ray diffraction exhibited an enhancement of crystallinity as well as crystallographic strain. Typical energy dispersive analysis of X-rays (EDAX) spectrum was carried out to study the interface mixing, if any, after the ion irradiation. The pristine sample exhibits a narrow hysteresis loop in the current voltage (I–V) curves with maximum RS ratio of 98. Highly reproducible resistive switching characteristics with pronounced loops in the I–V curves have been observed for the irradiated Ag/Cr:SZO/SRO structure with maximum RS ratio of 985. I–V curves in low resistive state (LRS) demonstrate linear Ohmic conduction mechanism for both positive as well as negative bias region. The high resistive state (HRS) is consistent with space charge limited (SCLC) mechanism. The observed electrical behavior can be attributed to the high energy density of electronic excitations resulting from the impact of swift heavy ions induced defects and strain.

  12. Evolution of glassy polymers used for gas separation following ion beam irradiation

    Science.gov (United States)

    Ilconich, Jeffery B.

    Commercial gas separation membranes are typically polymeric because of low cost, processibility and wide range of available properties. However, while much work has been done to develop improved polymers for membranes, these materials have limitations for many applications. Therefore, much work has been focused in post-formation modification of polymer membrane. In this work, two very different polymers were modified by ion irradiation to evaluate the evolution in chemical structure, microstructure and permeation properties. A specific focus was on the impact of ion choice on properties of a specific polymer. The first part of study focused on evolution in a typical commercial membrane polymer, polysulfone, following H+ irradiation. Ion irradiation of polysulfone resulted in significant evolution in chemical structure at intermediate H+ doses. There was a general decrease in permeance with little improvement in selectivity following irradiation. Modification of asymmetric polysulfone membranes by H+ and C- irradiation resulted in significant damage to the porous substrate of the membranes. Therefore, these membranes exhibited larger decreases in permeance then could be attributed to changes in the selective layer. The polyimide, 6FDA-6FpDA, was irradiated with three different ions, (H+, N+ and F+) to investigate impact of ion mass and energy transfer mechanisms. As expected the polymer responded different to the different ions at similar overall doses and total energy transfer. In general, more damage to the polymer matrix was achieved with larger mass ions. The larger relative evolution to microstructure was attributed to the greater nuclear loss mechanism for N+ and F+ relative to H+. Significant evolution in permeation properties corresponded to this change in chemical structure and microstructure. While the ions exhibited similar trends in evolution in permeation properties, there were large differences in scale of modification. For example, at high dose H

  13. Effects of low-dose heavy ion irradiation on male germ cell adaptation and genetics

    Institute of Scientific and Technical Information of China (English)

    ZHANG Hong; LI Wen-Jian; ZHENG Rong-Liang

    2005-01-01

    The heavy ions with high linear energy transfer and high relative biological effectiveness are much more deleterious on the male germ cells, ones of the most radiosensitive cells of the body, than low-LET ionizing radiation such as X-ray or gamma-ray. The effects of low-dose heavy ion irradiation on male germ cell adaptation and genetics and the possible mechanism of this adaptation are summarized in our laboratory. Our results showed that the heavy ion irradiation significantly increased the frequencies of chromosomal aberrations in spermatogonia and spermatocytes of mice, the low dose heavy ion irradiation could induce significant adaptative response on mouse testes and human sperm, and pre-exposure of mouse testes with low-dose heavy ion can markedly alleviate damage effects induced by subsequent high-dose irradiation. The increase of SOD activity and decrease of lipid peroxidation levels induced by low-dose ionizing radiation may be involved in this adaptative response mechanism. These studies may provide useful theoretical and clinical bases for radioprotection of reproductive potential and assessment of genetic risks for human exposed to heavy ions in radiotherapy and in outer space environment.

  14. A Preliminary Study of the Application of a Model Animal-Caenorhabidity elegans' Exposure to a Low-Energy Ion Irradiation System

    Institute of Scientific and Technical Information of China (English)

    LIU Xuelan; CAI Kezhou; FENG Huiyun; XU An; YUAN Hang; YU Zengliang

    2007-01-01

    Because of the lack of suitable animal models adapted to high vacuum stress in the low-energy ion implantation system, the bio-effects ion irradiation with an energy less than 50 keV on multi-cellular animal individuals have never been investigated so far. The nematode Caenorhabditis elegans has proved to be an excellent animal model used for the study of a broad spectrum of biological issues. The purpose of this work was to investigate the viability of this animal under ion irradiation. We studied the protection effects of glycerol and trehalose on the enhancement of nematodes' ability to bear the vacuum stress. The results showed that the survival of the nematodes was enhanced remarkably under long and slow desiccation, even without glycerol and trehalose. 15% glycerol showed a better anti-vacuum stress effect on the nematodes than trehalose did under short-time desiccation. Low-temperature pre-treatment or post-treatment of the samples had no obvious effect on the survival scored after argon ion irradiation. Moreover, little effect was induced by 15% glycerol- and vacuum-exposure on germ cell apoptosis, compared to the untreated control sample. It issuggested that such treatment would provide relatively low background for genotoxic evaluations with ion irradiation.

  15. A Preliminary Study of the Application of a Model Animal-Caenorhabidity elegans' Exposure to a Low-Energy Ion Irradiation System

    Science.gov (United States)

    Liu, Xuelan; Cai, Kezhou; Feng, Huiyun; Xu, An; Yuan, Hang; Yu, Zengliang

    2007-10-01

    Because of the lack of suitable animal models adapted to high vacuum stress in the low-energy ion implantation system, the bio-effects ion irradiation with an energy less than 50 keV on multi-cellular animal individuals have never been investigated so far. The nematode Caenorhabditis elegans has proved to be an excellent animal model used for the study of a broad spectrum of biological issues. The purpose of this work was to investigate the viability of this animal under ion irradiation. We studied the protection effects of glycerol and trehalose on the enhancement of nematodes' ability to bear the vacuum stress. The results showed that the survival of the nematodes was enhanced remarkably under long and slow desiccation, even without glycerol and trehalose. 15% glycerol showed a better anti-vacuum stress effect on the nematodes than trehalose did under short-time desiccation. Low-temperature pre-treatment or post-treatment of the samples had no obvious effect on the survival scored after argon ion irradiation. Moreover, little effect was induced by 15% glycerol- and vacuum-exposure on germ cell apoptosis, compared to the untreated control sample. It issuggested that such treatment would provide relatively low background for genotoxic evaluations with ion irradiation.

  16. Opto-chemical response of Makrofol-KG to swift heavy ion irradiation

    Indian Academy of Sciences (India)

    Ambika Negi; R V Hariwal; Anju Semwal; R G Sonkawede; D Kanjilal; J M S Rana; R C Ramola

    2011-10-01

    In the present study, the effects of swift heavy ion beam irradiation on the structural, chemical and optical properties of Makrofol solid-state nuclear track detector (SSNTD) were investigated. Makrofol-KG films of 40 m thickness were irradiated with oxygen beam (8+) with fluences ranging between 1010 ion/cm2 and 1012 ion/cm2. Structural, chemical and optical properties were investigated using X-ray diffraction, FTIR spectroscopy and UV–visible spectroscopy methods. It is observed that the direct and indirect band gaps of Makrofol-KG decrease after the irradiation. The XRD study shows that the crystalline size in the films decreases at higher fluences. The intensity plots of FTIR measurements indicate the degradation of Makrofol at higher fluences. Roughness of the surface increases at higher fluence.

  17. Pulsed laser irradiation-induced microstructures in the Mn ion implanted Si

    Energy Technology Data Exchange (ETDEWEB)

    Naito, Muneyuki, E-mail: naito22@center.konan-u.ac.jp [Department of Chemistry, Konan University, Okamoto, Higashi-Nada, Kobe, Hyogo 658-8501 (Japan); CREST, Japan Science and Technology Agency, Kawaguchi, Saitama 332-0012 (Japan); Yamada, Ryo; Machida, Nobuya [Department of Chemistry, Konan University, Okamoto, Higashi-Nada, Kobe, Hyogo 658-8501 (Japan); Koshiba, Yusuke; Sugimura, Akira; Aoki, Tamao; Umezu, Ikurou [Department of Physics, Konan University, Okamoto, Higashi-Nada, Kobe, Hyogo 658-8501 (Japan)

    2015-12-15

    We have examined microstructures induced by pulsed-laser-melting for the Mn ion implanted Si using transmission electron microscopy. Single crystalline Si(0 0 1) wafers were irradiated with 65 keV and 120 keV Mn ions to a fluence of 1.0 × 10{sup 16}/cm{sup 2} at room temperature. The ion beam-induced amorphous layers in the as-implanted samples were melted and resolidified by pulsed YAG laser irradiation. After laser irradiation with appropriate laser fluence, the surface amorphous layers recrystallize into the single crystalline Si. The Mn concentration becomes higher in the near-surface region with increasing the number of laser shots. The migrated Mn atoms react with Si atoms and form the amorphous Mn–Si in the Si matrix.

  18. Swift heavy ion irradiation of metal containing tetrahedral amorphous carbon films

    Science.gov (United States)

    Karaseov, P. A.; Protopopova, V. S.; Karabeshkin, K. V.; Shubina, E. N.; Mishin, M. V.; Koskinen, J.; Mohapatra, S.; Tripathi, A.; Avasthi, D. K.; Titov, A. I.

    2016-07-01

    Thin carbon films were grown at room temperature on (0 0 1) n-Si substrate using dual cathode filtered vacuum arc deposition system. Graphite was used as a source of carbon atoms and separate metallic electrode was simultaneously utilized to introduce Ni or Cu atoms. Films were irradiated by 100 MeV Ag7+ ions to fluences in the range 1 × 1010-3 × 1011 cm-2. Rutherford backscattering spectroscopy, Raman scattering, scanning electron microscopy and atomic force microscopy in conductive mode were used to investigate film properties and structure change under irradiation. Some conductive channels having metallic conductivity type were found in the films. Number of such channels is less than number of impinged ions. Presence of Ni and Cu atoms increases conductivity of those conductive channels. Fluence dependence of all properties studied suggests different mechanisms of swift heavy ion irradiation-induced transformation of carbon matrix due to different chemical effect of nickel and copper atoms.

  19. Changes in the surface electronic states of semiconductor fine particles induced by high energy ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Yamaki, Tetsuya; Asai, Keisuke; Ishigure, Kenkichi [Tokyo Univ. (Japan); Shibata, Hiromi

    1997-03-01

    The changes in the surface electronic states of Q-sized semiconductor particles in Langmuir-Blodgett (LB) films, induced by high energy ion irradiation, were examined by observation of ion induced emission and photoluminescence (PL). Various emission bands attributed to different defect sites in the band gap were observed at the initial irradiation stage. As the dose increased, the emissions via the trapping sites decreased in intensity while the band-edge emission developed. This suggests that the ion irradiation would remove almost all the trapping sites in the band gap. The low energy emissions, which show a multiexponential decay, were due to a donor-acceptor recombination between the deeply trapped carriers. It was found that the processes of formation, reaction, and stabilization of the trapping sites would predominantly occur under the photooxidizing conditions. (author)

  20. Study of the degradation process of polyimide induced by high energetic ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Severin, Daniel

    2008-09-19

    The dissertation focuses on the radiation hardness of Kapton under extreme radiation environment conditions. To study ion-beam induced modifications, Kapton foils were irradiated at the GSI linear accelerator UNILAC using several projectiles (e.g. Ti, Mo, Au, and U) within a large fluence regime (1 x 10{sup 10}-5 x 10{sup 12} ions/cm{sup 2}). The irradiated Kapton foils were analysed by means of infrared and UV/Vis spectroscopy, tensile strength measurement, mass loss analysis, and dielectric relaxation spectroscopy. For testing the radiation stability of Kapton at the cryogenic operation temperature (5-10 K) of the superconducting magnets, additional irradiation experiments were performed at the Grand Accelerateur National d' Ions Lourds (GANIL, France) focusing on the online analysis of the outgassing process of small volatile degradation fragments. The investigations of the electrical properties analysed by dielectric relaxation spectroscopy exhibit a different trend: high fluence irradiations with light ions (e.g. Ti) lead to a slight increase of the conductivity, whereas heavy ions (e.g. Sm, Au) cause a drastic change already in the fluence regime of nonoverlapping tracks (5 x 10{sup 10} ions/cm{sup 2}). Online analysis of the outgassing process during irradiation at cryogenic temperatures shows the release of a variety of small gaseous molecules (e.g. CO, CO{sub 2}, and short hydro carbons). Also a small amount of large polymer fragments is identified. The results allow the following conclusions which are of special interest for the application of Kapton as insulating material in a high-energetic particle radiation environment. a) The material degradation measured with the optical spectroscopy and tensile strength tests are scalable with the dose deposited by the ions. The high correlation of the results allows the prediction of the mechanical degradation with the simple and non-destructive infrared spectroscopy. The degradation curve points to a

  1. Nitric oxide-mediated bystander signal transduction induced by heavy-ion microbeam irradiation

    Science.gov (United States)

    Tomita, Masanori; Matsumoto, Hideki; Funayama, Tomoo; Yokota, Yuichiro; Otsuka, Kensuke; Maeda, Munetoshi; Kobayashi, Yasuhiko

    2015-07-01

    In general, a radiation-induced bystander response is known to be a cellular response induced in non-irradiated cells after receiving bystander signaling factors released from directly irradiated cells within a cell population. Bystander responses induced by high-linear energy transfer (LET) heavy ions at low fluence are an important health problem for astronauts in space. Bystander responses are mediated via physical cell-cell contact, such as gap-junction intercellular communication (GJIC) and/or diffusive factors released into the medium in cell culture conditions. Nitric oxide (NO) is a well-known major initiator/mediator of intercellular signaling within culture medium during bystander responses. In this study, we investigated the NO-mediated bystander signal transduction induced by high-LET argon (Ar)-ion microbeam irradiation of normal human fibroblasts. Foci formation by DNA double-strand break repair proteins was induced in non-irradiated cells, which were co-cultured with those irradiated by high-LET Ar-ion microbeams in the same culture plate. Foci formation was suppressed significantly by pretreatment with an NO scavenger. Furthermore, NO-mediated reproductive cell death was also induced in bystander cells. Phosphorylation of NF-κB and Akt were induced during NO-mediated bystander signaling in the irradiated and bystander cells. However, the activation of these proteins depended on the incubation time after irradiation. The accumulation of cyclooxygenase-2 (COX-2), a downstream target of NO and NF-κB, was observed in the bystander cells 6 h after irradiation but not in the directly irradiated cells. Our findings suggest that Akt- and NF-κB-dependent signaling pathways involving COX-2 play important roles in NO-mediated high-LET heavy-ion-induced bystander responses. In addition, COX-2 may be used as a molecular marker of high-LET heavy-ion-induced bystander cells to distinguish them from directly irradiated cells, although this may depend on the time

  2. Development and performance evaluation of a three-dimensional clinostat synchronized heavy-ion irradiation system

    Science.gov (United States)

    Ikeda, Hiroko; Souda, Hikaru; Puspitasari, Anggraeini; Held, Kathryn D.; Hidema, Jun; Nikawa, Takeshi; Yoshida, Yukari; Kanai, Tatsuaki; Takahashi, Akihisa

    2017-02-01

    Outer space is an environment characterized by microgravity and space radiation, including high-energy charged particles. Astronauts are constantly exposed to both microgravity and radiation during long-term stays in space. However, many aspects of the biological effects of combined microgravity and space radiation remain unclear. We developed a new three-dimensional (3D) clinostat synchronized heavy-ion irradiation system for use in ground-based studies of the combined exposures. Our new system uses a particle accelerator and a respiratory gating system from heavy-ion radiotherapy to irradiate samples being rotated in the 3D clinostat with carbon-ion beams only when the samples are in the horizontal position. A Peltier module and special sample holder were loaded on a static stage (standing condition) and the 3D clinostat (rotation condition) to maintain a suitable temperature under atmospheric conditions. The performance of the new device was investigated with normal human fibroblasts 1BR-hTERT in a disposable closed cell culture chamber. Live imaging revealed that cellular adhesion and growth were almost the same for the standing control sample and rotation sample over 48 h. Dose flatness and symmetry were judged according to the relative density of Gafchromic films along the X-axis and Y-axis of the positions of the irradiated sample to confirm irradiation accuracy. Doses calculated using the carbon-ion calibration curve were almost the same for standing and rotation conditions, with the difference being less than 5% at 1 Gy carbon-ion irradiation. Our new device can accurately synchronize carbon-ion irradiation and simulated microgravity while maintaining the temperature under atmospheric conditions at ground level.

  3. Positron annihilation study of the hardening behavior in Al-Cu based alloy by electron and heavy ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Hori, Fuminobu; Kobayashi, Ippei; Iwase, Akihiro [Department of Materials Science, Osaka Prefecture University, 1-1 Gakuen-cho, Sakai, Osaka 599-8531 (Japan); Saito, Yuichi; Ishikawa, Norito; Oshima, Takeshi, E-mail: horif@mtr.osakafu-u.ac.j [JAEA Tokai, Tokai-mura, Naka-gun, Ibaraki 319-1195 (Japan)

    2010-04-01

    Al-Cu based alloy, which is generally called duralumin (JIS2017), was irradiated with 10 MeV Iodine ions, 200 MeV Xenon ions and 3 MeV electrons at room temperature respectively. The micro Vicker's hardness and positron annihilation coincidence Doppler broadening (CDB) measurements have been performed before and after irradiation. Only in the case of ion irradiation, the Vicker's hardness increases with increasing ion dose. Nevertheless, there was no difference in the profile CDB spectrum for before and after irradiation. On the other hand, we found that the micro hardness of this alloy, which was Xe ion irradiated and subsequently annealed at 423 K, is greater than that of age hardened alloy without irradiation. CDB ratio curve of the age hardened Duralumin is clearly different in the electron momentum range around 0.015-0.025 mc from that of the ion irradiated alloy. The results of three-dimensional atom probe (3DAP) also show that a lot of small clusters were found after ion irradiation but large precipitations have found in annealed Duralumin. These results reveal that a number of small clusters formed in this alloy after ion irradiation, and they should strongly affects the micro hardness.

  4. Effect of swift heavy ion irradiation on single- and multiwalled carbon nanotubes

    Energy Technology Data Exchange (ETDEWEB)

    Olejniczak, Andrzej, E-mail: aolejnic@chem.uni.torun.pl [Flerov Laboratory of Nuclear Reactions, Joint Institute for Nuclear Research, Dubna 141980 (Russian Federation); Faculty of Chemistry, Nicolaus Copernicus University, ul. Gagarina 7, 87-100 Toruń (Poland); Skuratov, Vladimir A. [Flerov Laboratory of Nuclear Reactions, Joint Institute for Nuclear Research, Dubna 141980 (Russian Federation)

    2014-05-01

    The effect of irradiation with swift heavy ions on the structure and properties of carbon nanotubes was investigated by Raman spectroscopy. It was found that disordering of the system occurred mainly at the surface. No ordering phenomena have been observed over a whole range of both fluences and electronic stopping powers studied. The disorder parameter (i.e., the ratio of the D and G band intensities (I{sub D}/I{sub G})) increases non-linearly with the irradiation dose, showing a tendency to saturate at high fluences. The increase in the disorder parameter upon irradiation was proportional to the square root of the ion fluence. The radiation stability of the few-walled nanotubes was ca. 1.6 higher than that of the single-walled ones. The irradiation with both the Xe and Kr ions leads to essentially the same increase in the I{sub D}/I{sub G} ratio with respect to the deposited electronic energy density. In the case of the Ar ion irradiation, the observed increase in the I{sub D}/I{sub G} ratio is much lower, suggesting that the electronic stopping power threshold for defects creation in carbon nanotubes is lower than that for graphite.

  5. Surface modification of InGaAs/GaAs heterostructures by swift heavy ion irradiation

    Science.gov (United States)

    Dhamodaran, S.; Pathak, A. P.; Avasthi, D. K.; Srinivasan, T.; Muralidharan, R.; Emfietzoglou, D.

    2007-04-01

    We investigate the surface morphology of molecular beam epitaxy (MBE) grown InGaAs/GaAs(0 0 1) heterostructures using atomic force microscope (AFM) before and after irradiation. Samples with layer thicknesses below critical layer thickness (i.e. fully strained) have smooth surface where as, the samples grown beyond critical layer thickness have cross hatch patterns at the surface. The transition from smooth to cross-hatch pattern may be used to identify the onset of strain relaxation. The samples were subjected to swift heavy ion (SHI) irradiation using 150 MeV Ag12+ ions with a fixed fluence of 1 × 1013 ions/cm2. The morphology of the strained samples was almost similar before and after irradiation where as, the partially relaxed samples were observed to have variations. The electronic energy loss of the incident ions which is dominant compared to the nuclear energy loss is effective to modify with the fluence used in the present study for partially relaxed samples. The relaxation of excited electron subsystem of the target results in the melting and re-growth which reflects in the surface morphology. The observed modifications at the surface may be attributed to (i) irradiation induced surface mass transport and (ii) interface modifications, where both these factors determine the surface morphology of heterostructures. The effects of irradiation on the surface and interface of the samples have been realized by AFM studies.

  6. Phase stability in thermally-aged CASS CF8 under heavy ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Li, Meimei; Miller, M; Chen, Wei-Ying

    2015-07-01

    The stability of the microstructure of a cast austenitic stainless steel (CASS), before and after heavy ion irradiation, was investigated by atom probe tomography (APT). A CF8 ferrite-austenite duplex alloy was thermally aged at 400 degrees C for 10,000 h. After this treatment, APT revealed nanometer-sized G-phase precipitates and Fe-rich alpha and Cr-enriched alpha' phase separated regions in the ferrite. The thermally-aged CF8 specimen was irradiated with 1 MeV Kr ions to a fluence of 1.88 x 10(19) ions/m(2) at 400 degrees C. After irradiation, APT analysis revealed a strong spatial/dose dependence of the G-phase precipitates and the alpha-alpha' spinodal decomposition in the ferrite. For the G-phase precipitates, the number density increased and the mean size decreased with increasing dose, and the particle size distribution changed considerably under irradiation. The inverse coarsening process can be described by recoil resolution. The amplitude of the alpha-alpha' spinodal decomposition in the ferrite was apparently reduced after heavy ion irradiation. (C) 2015 Elsevier B.V. All rights reserved

  7. Optical properties in the Cu-fused silica system irradiated with swift heavy ions

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, Ranjana C. [Department of Physics, University of Mumbai, Vidyanagari, Santacruz East, Mumbai 400 098 (India); Kothari, D.C. [Department of Physics, University of Mumbai, Vidyanagari, Santacruz East, Mumbai 400 098 (India)]. E-mail: kothari@mu.ac.in; Choudhari, R.J. [Nuclear Science Centre, P.O. Box 10502, Aruna Asaf Ali Marg, New Delhi 110 067 (India); Kumar, Ravi [Nuclear Science Centre, P.O. Box 10502, Aruna Asaf Ali Marg, New Delhi 110 067 (India); Sahoo, P.K. [II. Physikalisches Institut, Universitaet Goettingen, Friedrich-Hund-Platz 1, D-37077 Goettingen (Germany); Lieb, K.P. [II. Physikalisches Institut, Universitaet Goettingen, Friedrich-Hund-Platz 1, D-37077 Goettingen (Germany); Klaumuenzer, S. [Hahn-Meitner Institut, Glienicker Str. 100, D-14109 Berlin (Germany)

    2006-04-15

    Swift heavy ions are used to study the effects of electronic energy loss on Cu cluster formation in fused silica after post-irradiation annealing. Fused silica substrates covered with 10 nm thin Cu-films were irradiated using beams of either 120 MeV Ag{sup 9+} ions or 350 MeV Au{sup 26+} ions at fluences ranging from 2 x 10{sup 13} to 1 x 10{sup 14} cm{sup -2}. After irradiation, the samples were annealed for 30 min in argon, at temperatures of 773-1200 K and characterized by UV-VIS absorption spectroscopy. The swift ion irradiations created E' and B{sub 2} defects in silica, which were partially eliminated during annealing. In addition, Cu cluster formation in silica was observed after annealing. Irradiation fluences exceeding 4 x 10{sup 13} cm{sup -2} and annealing temperatures above 1100 K are more effective in forming larger nanoclusters.

  8. Induction of the Tn10 Precise Excision in E. coli Cells after Accelerated Heavy Ions Irradiation

    CERN Document Server

    Zhuravel, D V

    2003-01-01

    The influence of the irradiation of different kinds on the indication of the structural mutations in the bacteria Escherichia coli is considered. The regularities of the Tn10 precise excision after accelerated ^{4}He and ^{12}C ions irradiations with different linear energy transfer (LET) were investigated. Dose dependences of the survival and relative frequency of the Tn10 precise excision were obtained. It was shown, that the relative frequency of the Tn10 precise excision is the exponential function from the irradiation dose. Relative biological efficiency (RBE), and relative genetic efficiency (RGE) were calculated, and were treated as the function of the LET.

  9. Metal impurity-assisted formation of nanocone arrays on Si by low energy ion-beam irradiation

    Science.gov (United States)

    Steeves Lloyd, Kayla; Bolotin, Igor L.; Schmeling, Martina; Hanley, Luke; Veryovkin, Igor V.

    2016-10-01

    Fabrication of nanocone arrays on Si surfaces was demonstrated using grazing incidence irradiation with 1 keV Ar+ ions concurrently sputtering the surface and depositing metal impurity atoms on it. Among three materials compared as co-sputtering targets Si, Cu and stainless steel, only steel was found to assist the growth of dense arrays of nanocones at ion fluences between 1018 and 1019 ions/cm2. The structural characterization of samples irradiated with these ion fluences using Scanning Electron Microscopy and Atomic Force Microscopy revealed that regions far away from co-sputtering targets are covered with nanoripples, and that nanocones popped-up out of the rippled surfaces when moving closer to co-sputtering targets, with their density gradually increasing and reaching saturation in the regions close to these targets. The characterization of the samples' chemical composition with Total Reflection X-ray Fluorescence Spectrometry and X-ray Photoelectron Spectroscopy revealed that the concentration of metal impurities originating from stainless steel (Fe, Cr and Ni) was relatively high in the regions with high density of nanocones (Fe reaching a few atomic percent) and much lower (factor of 10 or so) in the region of nanoripples. Total Reflection X-ray Fluorescence Spectrometry measurements showed that higher concentrations of these impurities are accumulated under the surface in both regions. X-ray Photoelectron Spectroscopy experiments showed no direct evidence of metal silicide formation occurring on one region only (nanocones or nanoripples) and thus showed that this process could not be the driver of nanocone array formation. Also, these measurements indicated enhancement in oxide formation on regions covered by nanocones. Overall, the results of this study suggest that the difference in concentration of metal impurities in the thin near-surface layer forming under ion irradiation might be responsible for the differences in surface structures.

  10. New ion beam materials laboratory for materials modification and irradiation effects research

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Y., E-mail: Zhangy1@ornl.gov [Materials Science and Technology Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Department of Materials Science and Engineering, University of Tennessee, Knoxville, TN 37996 (United States); Crespillo, M.L.; Xue, H.; Jin, K.; Chen, C.H. [Department of Materials Science and Engineering, University of Tennessee, Knoxville, TN 37996 (United States); Fontana, C.L. [Materials Science and Technology Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Graham, J.T. [Department of Materials Science and Engineering, University of Tennessee, Knoxville, TN 37996 (United States); Weber, W.J., E-mail: wjweber@utk.edu [Department of Materials Science and Engineering, University of Tennessee, Knoxville, TN 37996 (United States); Materials Science and Technology Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States)

    2014-11-01

    A new multifunctional ion beam materials laboratory (IBML) has been established at the University of Tennessee, in partnership with Oak Ridge National Laboratory. The IBML is currently equipped with two ion sources, a 3 MV tandem accelerator, three beamlines and three endstations. The IBML is primarily dedicated to fundamental research on ion–solid interaction, ion beam analysis, ion beam modification, and other basic and applied research on irradiation effects in a wide range of materials. An overview of the IBML facility is provided, and experimental results are reported to demonstrate the specific capabilities.

  11. Effect of heavy ion irradiation on thermodynamically equilibrium Zr-Excel alloy

    Science.gov (United States)

    Yu, Hongbing; Liang, Jianlie; Yao, Zhongwen; Kirk, Mark A.; Daymond, Mark R.

    2017-05-01

    The thermodynamically equilibrium state was achieved in a Zr-Sn-Nb-Mo alloy by long-term annealing at an intermediate temperature. The fcc intermetallic Zr(Mo, Nb)2 enriched with Fe was observed at the equilibrium state. In-situ 1 MeV Kr2+ heavy ion irradiation was performed in a TEM to study the stability of the intermetallic particles under irradiation and the effects of the intermetallic particle on the evolution of type dislocation loops at different temperatures from 80 to 550 °C. Chemi-STEM elemental maps were made at the same particles before and after irradiation up to 10 dpa. It was found that no elemental redistribution occurs at 200 °C and below. Selective depletion of Fe was observed from some precipitates under irradiation at higher temperatures. No change in the morphology of particles and no evidence showing a crystalline to amorphous transformation were observed at all irradiation temperatures. The formation of type dislocation loops was observed under irradiation at 80 and 200 °C, but not at 450 and 550 °C. The loops were non-uniformly distributed; a localized high density of type dislocation loops were observed near the second phase particles; we suggest that loop nucleation is favored as a result of the stress induced by the particles, rather than by elemental redistribution. The stability of the second phase particles and the formation of the type loops under heavy ion irradiation are discussed.

  12. In situ study of defect accumulation in zirconium under heavy ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Idrees, Y. [Department of Mechanical and Materials Engineering, Queen’s University, Kingston, ON, Canada K7L 3N6 (Canada); Yao, Z., E-mail: yaoz@me.queensu.ca [Department of Mechanical and Materials Engineering, Queen’s University, Kingston, ON, Canada K7L 3N6 (Canada); Kirk, M.A. [Material Science Division, Argonne National Laboratory, Argonne, IL 60439 (United States); Daymond, M.R. [Department of Mechanical and Materials Engineering, Queen’s University, Kingston, ON, Canada K7L 3N6 (Canada)

    2013-02-15

    In this study, we report direct observations on heavy ion (Kr{sup 2+}) irradiation induced changes in microstructures of pure Zr at different temperatures using intermediate voltage electron microscopy. Thin TEM foils were irradiated with 1 MeV Kr{sup 2+} ions. Materials have been irradiated to different damage levels ranging from 0.008 dpa to 1 dpa at different temperatures ranging from 300 °C to 500 °C. We particularly concentrate on yield of small defects directly occurring from cascade collapse at very low doses, and their evolution as the dose increases. In situ observation of growth and evolution of these small defects into complex defect structures at high dose has been carried out. Irradiation of materials at different temperatures provided an opportunity to investigate the temperature dependence of defect accumulation in Zr during irradiation. The differences in defect structures, defect densities, and therefore dynamic growth have been discussed in detail as a function of irradiation parameters (dose, temperature). Interaction of irradiation induced defects with existing microstructure and other defects is discussed.

  13. Broad-beam three-dimensional irradiation system for heavy-ion radiotherapy at HIMAC

    CERN Document Server

    Futami, Y; Fujita, M; Tomura, H; Higashi, A; Matsufuji, N; Miyahara, N; Endo, M; Kawachi, K

    1999-01-01

    A three-dimensional irradiation system using a broad beam has been installed for heavy-ion cancer therapy at the Heavy Ion Medical Accelerator in Chiba (HIMAC) facility. Only the target region is irradiated at the 100% dose level; the dose level at other parts of irradiated tissues is less, using a range shifter, a multileaf collimator and a compensator. The devices are the same as those used in two-dimensional irradiation, except that the setting values of the devices can be dynamically changed during the treatment. The thickness of the absorber and the aperture of the multileaf collimator are dynamically controlled during irradiation, so that the Bragg peak is swept in the depth direction and the Bragg peak outside of the target volume is blocked by the multileaf collimator. The performance of this system was checked by irradiation of a phantom using a 290 MeV/nucleon carbon beam. The dose distribution realized by this three-dimensional irradiation agreed satisfactorily with the planned one.

  14. Enhanced hydrogen production of Enterobacter aerogenes mutated by nuclear irradiation.

    Science.gov (United States)

    Cheng, Jun; Liu, Min; Song, Wenlu; Ding, Lingkan; Liu, Jianzhong; Zhang, Li; Cen, Kefa

    2017-03-01

    Nuclear irradiation was used for the first time to generate efficient mutants of hydrogen-producing bacteria Enterobacter aerogenes, which were screened with larger colour circles of more fermentative acid by-products. E. aerogenes cells were mutated by nuclear irradiation of (60)Co γ-rays. The screened E. aerogenes ZJU1 mutant with larger colour circles enhanced the hydrogenase activity from 89.8 of the wild strain to 157.4mLH2/(gDWh). The hereditary stability of the E. aerogenes ZJU1 mutant was certified after over ten generations of cultivation. The hydrogen yield of 301mLH2/gglucose with the mutant was higher by 81.8% than that of 166mL/gglucose with the wild strain. The peak hydrogen production rate of 27.2mL/(L·h) with the mutant was higher by 40.9% compared with that of 19.3mL/(L·h) with the wild strain. The mutant produced more acetate and butyrate but less ethanol compared with the wild strain during hydrogen fermentation.

  15. Positron annihilation lifetime characterization of oxygen ion irradiated rutile TiO{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Luitel, Homnath [Variable Energy Cyclotron Centre, 1/AF Bidhannagar, Kolkata 700064 (India); Sarkar, A. [Department of Physics, Bangabasi Morning College, 19 Rajkumar Chakraborty Sarani, Kolkata 700009 (India); Chakrabarti, Mahuya [Department of Physics, Acharya Prafulla Chandra College, New Barrackpore, Kolkata 700131 (India); Chattopadhyay, S. [Department of Physics, Maulana Azad College, 8 Rafi Ahmed Kidwai Road, Kolkata 700013 (India); Asokan, K. [Inter University Accelerator Centre, Aruna Asaf Ali Marg, New Delhi 110067 (India); Sanyal, D., E-mail: dirtha@vecc.gov.in [Variable Energy Cyclotron Centre, 1/AF Bidhannagar, Kolkata 700064 (India)

    2016-07-15

    Ferromagnetic ordering at room temperature has been induced in rutile phase of TiO{sub 2} polycrystalline sample by O ion irradiation. 96 MeV O ion induced defects in rutile TiO{sub 2} sample has been characterized by positron annihilation spectroscopic techniques. Positron annihilation results indicate the formation of cation vacancy (V{sub Ti}, Ti vacancy) in these irradiated TiO{sub 2} samples. Ab initio density functional theoretical calculations indicate that in TiO{sub 2} magnetic moment can be induced either by creating Ti or O vacancies.

  16. Optimization of nanopores obtained by chemical etching on swift-ion irradiated lithium niobate

    Energy Technology Data Exchange (ETDEWEB)

    Crespillo, M.L.; Otto, M.; Munoz-Martin, A. [Centro de Microanalisis de Materiales (CMAM), Universidad Autonoma de Madrid (UAM), Cantoblanco, E-28049 Madrid (Spain); Olivares, J. [Centro de Microanalisis de Materiales (CMAM), Universidad Autonoma de Madrid (UAM), Cantoblanco, E-28049 Madrid (Spain); Instituto de Optica, CSIC, C/Serrano 121, E-28006 Madrid (Spain)], E-mail: j.olivares@io.cfmac.csic.es; Agullo-Lopez, F. [Centro de Microanalisis de Materiales (CMAM), Universidad Autonoma de Madrid (UAM), Cantoblanco, E-28049 Madrid (Spain); Departamento de Fisica de Materiales, Universidad Autonoma de Madrid (UAM) Cantoblanco, 28049 Madrid (Spain); Seibt, M. [IV. Physikalisches Institut, Universitaet Goettingen, Institut fuer Halbleiterphysik, Tammannstr. 1, D-37077 Goettingen (Germany); Toulemonde, M. [Centre Interdisciplinaire de Recherche Ions-Lasers, UMR 11 CEA-CNRS, 14040 Caen Cedex (France); Trautmann, C. [Gesellschaft fuer Schwerionenforschung (GSI), Materialforschung, Planckstrasse 1, 64291 Darmstadt (Germany)

    2009-03-15

    The morphology of the nanopores obtained by chemical etching on ion-beam irradiated LiNbO{sub 3} has been investigated for a variety of ions (F, Br, Kr, Cu, Pb), energies (up to 2300 MeV), and stopping powers (up to 35 keV/nm) in the electronic energy loss regime. The role of etching time and etching agent on the pore morphology, diameter, depth, and shape has also been studied. The transversal and depth profiles of the pore have been found to be quite sensitive to both irradiation and etching parameters. Moreover, two etching regimes with different morphologies and etching rates have been identified.

  17. Large scale silver nanowires network fabricated by MeV hydrogen (H+) ion beam irradiation

    Science.gov (United States)

    Honey, S.; Naseem, S.; Ishaq, A.; Maaza, M.; Bhatti, M. T.; Wan, D.

    2016-04-01

    A random two-dimensional large scale nano-network of silver nanowires (Ag-NWs) is fabricated by MeV hydrogen (H+) ion beam irradiation. Ag-NWs are irradiated under H+ ion beam at different ion fluences at room temperature. The Ag-NW network is fabricated by H+ ion beam-induced welding of Ag-NWs at intersecting positions. H+ ion beam induced welding is confirmed by transmission electron microscopy (TEM) and scanning electron microscopy (SEM). Moreover, the structure of Ag NWs remains stable under H+ ion beam, and networks are optically transparent. Morphology also remains stable under H+ ion beam irradiation. No slicings or cuttings of Ag-NWs are observed under MeV H+ ion beam irradiation. The results exhibit that the formation of Ag-NW network proceeds through three steps: ion beam induced thermal spikes lead to the local heating of Ag-NWs, the formation of simple junctions on small scale, and the formation of a large scale network. This observation is useful for using Ag-NWs based devices in upper space where protons are abandoned in an energy range from MeV to GeV. This high-quality Ag-NW network can also be used as a transparent electrode for optoelectronics devices. Project supported by the National Research Foundation of South Africa (NRF), the French Centre National pour la Recherche Scientifique, iThemba-LABS, the UNESCO-UNISA Africa Chair in Nanosciences & Nanotechnology, the Third World Academy of Science (TWAS), Organization of Women in Science for the Developing World (OWSDW), the Abdus Salam ICTP via the Nanosciences African Network (NANOAFNET), and the Higher Education Commission (HEC) of Pakistan.

  18. Effect of low energy ion beam irradiation on wettability of narra (Pterocarpus indicus) wood chips

    Energy Technology Data Exchange (ETDEWEB)

    Ramos, Henry J. [Plasma Physics Laboratory, National Institute of Physics, University of the Philippines, Diliman, Quezon City 1101 (Philippines)]. E-mail: hjr@nsri.upd.edu.ph; Monasterial, Jonathan Lee C. [Plasma Physics Laboratory, National Institute of Physics, University of the Philippines, Diliman, Quezon City 1101 (Philippines); Blantocas, Gene Q. [Plasma Physics Laboratory, National Institute of Physics, University of the Philippines, Diliman, Quezon City 1101 (Philippines)

    2006-01-15

    Narra (Pterocarpus indicus) wood chips were irradiated with positive hydrogen ions H{sup +} and H{sub 2}{sup +} to make them hydrophobic. The ions were produced and extracted from a gas discharge ion source. The extracted beam current ranges from 0.01 to 0.07{mu}A for discharge currents of 1.0-4.0mA, discharge potential between 600V and 1000V. The chips, positioned at 70mm downstream from the ion source, were processed for different time periods and discharge currents. The wettability was characterized by the contact angle of the liquid droplet with respect to the wood surface. Surface modifications were assessed with by measurements of the water contact angle. Tests indicate retarded absorption characteristics for ion-irradiated samples compared to controlled samples. The longest absorptive inhibition were exhibited by samples irradiated for 30min, at discharge current of 1.0mA, 720eV ion energy and 0V extraction potential. Scanning electron micrographs reveal the difference in morphologies of treated and untreated samples. The results prove that low energy beams of hydrogen from a gas discharge ion source are suitable in transforming surfaces of wood chips to be water resistant.

  19. Effect of low energy ion beam irradiation on wettability of narra ( Pterocarpus indicus) wood chips

    Science.gov (United States)

    Ramos, Henry J.; Monasterial, Jonathan Lee C.; Blantocas, Gene Q.

    2006-01-01

    Narra (Pterocarpus indicus) wood chips were irradiated with positive hydrogen ions H+ and H2+ to make them hydrophobic. The ions were produced and extracted from a gas discharge ion source. The extracted beam current ranges from 0.01 to 0.07 μA for discharge currents of 1.0-4.0 mA, discharge potential between 600 V and 1000 V. The chips, positioned at 70 mm downstream from the ion source, were processed for different time periods and discharge currents. The wettability was characterized by the contact angle of the liquid droplet with respect to the wood surface. Surface modifications were assessed with by measurements of the water contact angle. Tests indicate retarded absorption characteristics for ion-irradiated samples compared to controlled samples. The longest absorptive inhibition were exhibited by samples irradiated for 30 min, at discharge current of 1.0 mA, 720 eV ion energy and 0 V extraction potential. Scanning electron micrographs reveal the difference in morphologies of treated and untreated samples. The results prove that low energy beams of hydrogen from a gas discharge ion source are suitable in transforming surfaces of wood chips to be water resistant.

  20. Sample Management System for Heavy Ion Irradiation Project

    Data.gov (United States)

    National Aeronautics and Space Administration — A robotic sample management device and system for the exposure of biological and material specimens to heavy ion beams of the NASA Space Radiation Laboratory (NSRL)...

  1. Silicon Carbide Power Device Performance Under Heavy-Ion Irradiation

    Science.gov (United States)

    Lauenstein, Jean-Marie; Casey, Megan; Topper, Alyson; Wilcox, Edward; Phan, Anthony; Ikpe, Stanley; LaBel, Ken

    2015-01-01

    Heavy-ion induced degradation and catastrophic failure data for SiC power MOSFETs and Schottky diodes are examined to provide insight into the challenge of single-event effect hardening of SiC power devices.

  2. Sample Management System for Heavy Ion Irradiation Project

    Data.gov (United States)

    National Aeronautics and Space Administration — A robotic sample management device and system for the exposure of biological and material specimens to heavy ion beams of the NASA Space Radiation Laboratory (NSRL)...

  3. Swift heavy-ion irradiation effects on electrical and defect properties of NPN transistors

    Science.gov (United States)

    Gnana Prakash, A. P.; Ke, S. C.; Siddappa, K.

    2004-08-01

    NPN transistors were irradiated by 95 MeV oxygen ions in a fluence ranging from 5 × 1010 to 5 × 1012 ions cm-2. The dc current gain (hFE), excess base current (DgrIB = IBpost - IBpre), excess collector current (DgrIC = ICpost - ICpre) and collector-saturation current (ICS) of the ion-irradiated transistors were studied systematically. We found that both hFE and ICS of the transistors decrease drastically after ion irradiation. Secondly, a significant increase in the collector current (IC) along with the increase in the base current (IB) after ion irradiation was observed. The radiation-induced trap levels in the collector-base depletion region of NPN transistors were studied by employing the deep level transient spectroscopy technique and different types of trap levels were observed. The results obtained on the activation energy, density of trap levels, apparent capture cross section of the defects, introduction rate and space charge layer lifetime of different defects for different total fluence are presented and discussed.

  4. Changes of structural and hydrogen desorption properties of MgH2 indused by ion irradiation

    Directory of Open Access Journals (Sweden)

    Kurko Sandra V.

    2010-01-01

    Full Text Available Changes in structural and hydrogen desorption properties of MgH2 induced by ion irradiation have been investigated. MgH2 powder samples have been irradiated with 45 keV B3+ and 120 keV Ar8+ions, with ion fluence of 1015 ions/cm2. The effects of ion irradiation are estimated by numerical calculations using SRIM package. The induced material modifications and their consequences on hydrogen dynamics in the system are investigated by XRD, particle size distribution and TPD techniques. Changes of TPD spectra with irradiation conditions suggest that there are several mechanisms involved in desorption process which depend on defect concentration and their interaction and ordering. The results confirmed that the near-surface area of MgH2 and formation of a substoichiometric MgHx (x<2 play a crucial role in hydrogen kinetics and that various concentrations of induced defects substantially influence H diffusion and desorption kinetics in MgH2. The results also confirm that there is possibility to control the thermodynamic parameters by controlling vacancies concentration in the system.

  5. Cu Ions Irradiation Impact on Structural and Optical Properties of GaN Thin Film

    Science.gov (United States)

    Shah, A.; Husnain, G.; Ahmad, Ishaq; Mahmood, Arshad

    2013-03-01

    Epitaxial grown Gallium nitride (GaN) thin film on sapphire was irradiated with Cu ions at various fluences (5×1014, 1 ×1015 and 5×1015cm-2). The level of lattice disorder, as measured by Rutherford backscattering spectrometry and channeling (RBS/C), gradually increases with the increasing of ions fluence. Lattice amorphization is observed for the sample irradiated with fluence of 5×1015cm-2 which is also confirmed by X-ray diffractometer (XRD) analysis. It was found that both Raman modes of GaN layer clearly shifted with Cu+ fluences. Both Raman and X-ray analyses explore that Cu atom substituted into Ga sites. Atomic force microscopy (AFM) images show the irradiated GaN surface roughness increases with the increasing ions fluence. The UV-visible transmittance spectrum and ellipsometric measurements show a decrease in the band gap value after irradiation of Cu ions in the GaN film. Moreover, the optical constants (n and k) of the films vary with the increasing of Cu ion fluences.

  6. Erosion and deuterium retention in ion-irradiated tungsten under plasma exposure

    Energy Technology Data Exchange (ETDEWEB)

    Khripunov, B., E-mail: Khripunov_BI@nrcki.ru [NRC Kurchatov Institute, Kurchatov Sq. 1, Moscow 123182 (Russian Federation); Gureev, V.; Koidan, V.; Kornienko, S.; Latushkin, S.; Petrov, V.; Ryazanov, A.; Semenov, E.; Stolyarova, V.; Danelyan, L. [NRC Kurchatov Institute, Kurchatov Sq. 1, Moscow 123182 (Russian Federation); Kulikauskas, V.; Zatekin, V. [Institute of Nuclear Physics, Lomonosov University, Moscow 119991 (Russian Federation); Unezhev, V. [NRC Kurchatov Institute, Kurchatov Sq. 1, Moscow 123182 (Russian Federation)

    2015-08-15

    Effect of radiation damage on tungsten response to plasma exposure is examined. Samples of tungsten W 99.95 wt% were irradiated with fast {sup 12}C{sup 3+} ions at 10 MeV to fluence of (1–2) × 10{sup 17} ion/cm{sup 2} to produce damage in the range 1–40 dpa relevant to the level of interest for fusion research. Exposure of the irradiated tungsten to deuterium plasma on linear simulator in erosion condition provided D-ion total fluence (1–3) × 10{sup 21} D{sup +}/cm{sup 2} at ion energy 250 eV. Swelling effect has been observed, and important changes in the structure of the irradiated material have been found (SEM). Erosion of the damaged layer was evaluated at Y{sub d-w} ≅ (3–5) ⋅ 10{sup −3} at/ion. The retained deuterium profiles have been taken by ERDA, maximal deuterium concentration reached 6–8 at.% in the layer ∼30 nm deep corresponding to 2–3 dpa. Comparison of D-retention was made for C- and He-irradiated tungsten for this level of damage.

  7. Microstructural response of InGaN to swift heavy ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, L. M.; Jiang, W.; Fadanelli, R. C.; Ai, W. S.; Peng, J. X.; Wang, T. S.; Zhang, C. H.

    2016-12-01

    A monocrystalline In0.18Ga0.82N film of ~275 nm in thickness grown on a GaN/Al2O3 substrate was irradiated with 290 MeV 238U32+ ions to a fluence of 1.2 x 12 cm-2 at room temperature. The irradiated sample was characterized using helium ion microscopy (HIM), Rutherford backscattering spectrometry under ion-channeling conditions (RBS/C), and high-resolution x-ray diffraction (HRXRD). The irradiation leads to formation of ion tracks throughout the thin In0.18Ga0.82N film and the 3.0 µm thick GaN buffer layer. The mean diameter of the tracks in In0.18Ga0.82N is ~9 nm, as determined by HIM examination. Combination of the HIM and RBS/C data suggests that the material in the track is likely to be highly disordered or fully amorphized, in contrast to a crystalline structure within the ion track in GaN. Lattice relaxation in In0.18Ga0.82N and a distribution of d-spacing of the (0002) planes in GaN with lattice expansion are observed after irradiation.

  8. 低能氮离子束与UV-B增强对水稻光合及蒸腾速率的影响%Effects of low-energy N+ion beam irradiation on photosynthetic and transpiration in rice under enhanced UV-B radiation

    Institute of Scientific and Technical Information of China (English)

    李林玉; 黄群策; 张书艮; 赵帅鹏

    2013-01-01

    moderated the damage caused by enhanced UV-B radiation, while more ways should be found and applied in this field. Low-energy N+ion implantation has been widely used in the mutation breeding of plant and microorganism due to its higher mutation frequency and wide mutation spectrum since the early 1980s. There are some reports showing that appropriate doses of low-energy N+ion beam treatment could inspire the anti-oxidative enzyme system and change the physicochemical characteristics in plant cells on some level, which could regulate its defense system to deal with the outside stress. However, there was no report about the interactions between enhanced UV-B radiation and low-energy N+ion beam radiation on rice. The effects of low-energy N+ion beam irradiation on diurnal variations of photosynthesis and photosynthetic pigment contents in rice under enhanced UV-B radiation were investigated in the study. The experiment materials were pre-treated by three different doses of low-energy N+ ion beam that was conducted in Henan provincial at a key laboratory of ion beam bio-engineering, Zhengzhou university, China. Then the test materials were planted in an experimental field and uniformly managed routinely. One month later, the rice seedlings were implanted into the planting boxes provided by the laboratory. After turning green, the seedlings were treated with UV-B radiation for two months (from 8:00 to 17:00 per day) except for rainy or cloudy days. The dose of enhanced UV-B radiation was 16.46 kJ/m2·d (a 20% difference in ambient UV-B, Zhengzhou, China) which was detected by an ultraviolet irradiation detector and normalized at 297nm to obtain effective radiation. Two months later, the photosynthetic parameters (Pn,Tr,Gs,Ci) were determined with a portable photosynthesis system (CB-1102, Beijing Yaxin Liyi Science and Technology Co., Ltd. China) every two hours from 7:00 a.m. to 17:00 p.m. on a cloudless day, and the photosynthetic pigment content was determined too. The

  9. Study of calf thymus DNA irradiated in vitro with MeV fluorine ions

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    A study of the fragments of DNA irradiated with MeV ions is important for the understanding of the DNA damage mechanism and the subsequent biological effects (induced by heavy ions). In this experiment, the products of calf thymus DNA (CT DNA) irradiated with MeV fluorine ions were analyzed using agarose gel electrophoresis,modified time-of-flight mass spectrometer (MALDI-TOF), and high-performance liquid chromatography (HPLC).The results showed that the molecular mass of the fragments were concentrated around 831 bp with agarose gel electrophoresis, there was no observable product in the range of 1,000- 30,000 (m/q) using MALDI-TOF, and small biomolecules were separated from the products. The results of this study indicated that the strand breaks of calf thymus DNA induced by MeV fluorine ions were nonrandom.

  10. Photoluminescence and Raman studies in swift heavy ion irradiated polycrystalline aluminum oxide

    Indian Academy of Sciences (India)

    K R Nagabhushana; B N Lakshminarasappa; Fouran Singh

    2009-10-01

    Polycrystalline aluminum oxide is synthesized by combustion technique and XRD studies of the sample revealed the -phase. The synthesized sample is irradiated with 120 MeV swift Au9+ ions for the fluence in the range from 1 × 1011 to 1 × 1013 ions cm-2. A broad photoluminescence (PL) emission with peak at ∼447 nm and two sharp emissions with peak at ∼ 679 and ∼ 695 nm are observed in pristine when sample was excited with 326 nm. However, in the irradiated samples the PL intensity at ∼ 447, 679 and 695 nm decreases with increase in ion fluence. The -Al2O3 gives rise to seven Raman modes with Raman intensity with peaks at ∼ 253, 396, 417, 546, 630, 842, 867 cm-1 observed in pristine. The intensity of these modes decreases with increase in ion fluence. However, the Raman modes observed at lower fluences are found to disappear at higher fluence.

  11. Transformation of multi walled carbon nanotubes irradiated by swift heavy ions

    Science.gov (United States)

    Vishalli; Avasthi, D. K.; Srivastava, Alok; Dharamvir, Keya

    2017-09-01

    The radiation stability of multiwalled carbon nanotube (MWCNT) buckypaper (BP) has been studied under extreme conditions. Samples of thick mat of MWCNT, called buckypaper, have been prepared by vacuum filtration method and were irradiated by 120 MeV Au ions with fluences ranging from 3 × 1011 ions/cm2 to 5 × 1013 ions/cm2. The samples were characterized by Field Emission Scanning Electron Microscopy (FESEM), High Resolution Transmission Electron Microscopy (HRTEM) and Raman spectroscopy. The surface imaging studies indicate the decrease in the average diameter of nanotubes under ion irradiation due to the sputtering of atoms from the CNT surface. Raman studies demonstrate initial healing at lower fluence, defect production at higher fluences and amorphization at highest fluence.

  12. Graphitic nanostripes in silicon carbide surfaces created by swift heavy ion irradiation.

    Science.gov (United States)

    Ochedowski, Oliver; Osmani, Orkhan; Schade, Martin; Bussmann, Benedict Kleine; Ban-d'Etat, Brigitte; Lebius, Henning; Schleberger, Marika

    2014-06-06

    The controlled creation of defects in silicon carbide represents a major challenge. A well-known and efficient tool for defect creation in dielectric materials is the irradiation with swift (E(kin) ≥ 500 keV/amu) heavy ions, which deposit a significant amount of their kinetic energy into the electronic system. However, in the case of silicon carbide, a significant defect creation by individual ions could hitherto not be achieved. Here we present experimental evidence that silicon carbide surfaces can be modified by individual swift heavy ions with an energy well below the proposed threshold if the irradiation takes place under oblique angles. Depending on the angle of incidence, these grooves can span several hundreds of nanometres. We show that our experimental data are fully compatible with the assumption that each ion induces the sublimation of silicon atoms along its trajectory, resulting in narrow graphitic grooves in the silicon carbide matrix.

  13. Irradiation of ionic liquid ion beams on silicon and glass substrates

    Energy Technology Data Exchange (ETDEWEB)

    Takeuchi, Mitsuaki, E-mail: m-takeuchi@kuee.kyoto-u.ac.jp; Hamaguchi, Takuya; Ryuto, Hiromichi; Takaoka, Gikan H.

    2013-11-15

    Irradiation of an ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate (BMIM-PF{sub 6}) ion beam on borosilicate glass and single crystalline Si(100) surface was demonstrated by using an ionic liquid ion source we developed. Surface smoothing on the glass substrates was produced by the irradiations at an acceleration voltage of 4 kV with both positive and negative ion beams, which include cation–anion pairs attached to a single ion of either polarity. Water contact angle measurements and X-ray photoelectron spectroscopy indicated that the surface smoothing was probably caused by surface modification involving nano-ordered chemical etching by Si–F reaction, implantation and deposition of P, N and C.

  14. Metastable phases in Zr-Excel alloy and their stability under heavy ion (Kr2+) irradiation

    Science.gov (United States)

    Yu, Hongbing; Zhang, Ken; Yao, Zhongwen; Kirk, Mark A.; Long, Fei; Daymond, Mark R.

    2016-02-01

    Zr-Excel alloy (Zr-3.5Sn-0.8Nb-0.8Mo, wt.%) has been proposed as a candidate material of pressure tubes in the CANDU-SCWR design. It is a dual-phase alloy containing primary hcp α-Zr and metastable bcc β-Zr. Metastable hexagonal ω-Zr phase could form in β-Zr as a result of aging during the processing of the tube. A synchrotron X-ray study was employed to study the lattice properties of the metastable phases in as-received Zr-Excel pressure tube material. In situ heavy ion (1 MeV Kr2+) irradiations were carried out at 200 °C and 450 °C to emulate the stability of the metastable phase under a reactor environment. Quantitative Chemi-STEM EDS analysis was conducted on both un-irradiated and irradiated samples to investigate alloying element redistribution induced by heavy ion irradiation. It was found that no decomposition of β-Zr was observed under irradiation at both 200 °C and 450 °C. However, ω-Zr particles experienced shape changes and shrinkage associated with enrichment of Fe at the β/ω interface during 200 °C irradiation but not at 450 °C. There is a noticeable increase in the level of Fe in the α matrix after irradiation at both 200 °C and 450 °C. The concentrations of Nb, Mo and Fe are increased in the ω phase but decreased in the β phase at 200 °C. The stability of metastable phases under heavy ion irradiation associated with elemental redistribution is discussed.

  15. Microstructural evolution of CANDU spacer material Inconel X-750 under in situ ion irradiation

    Science.gov (United States)

    Zhang, He Ken; Yao, Zhongwen; Judge, Colin; Griffiths, Malcolm

    2013-11-01

    Work on Inconel®Inconel® is a registered trademark of Special Metals Corporation that refers to a family of austenitic nickel-chromium-based superalloys.1 X-750 spacers removed from CANDU®CANDU® is a registered trademark of Atomic Energy of Canada Limited standing for ''CANada Deuterium Uranium''.2 reactors has shown that they become embrittled and there is development of many small cavities within the metal matrix and along grain boundaries. In order to emulate the neutron irradiation induced microstructural changes, heavy ion irradiations (1 MeV Kr2+ ions) were performed while observing the damage evolution using an intermediate voltage electron microscope (IVEM) operating at 200 kV. The irradiations were carried out at various temperatures 60-400 °C. The principal strengthening phase, γ‧, was disordered at low doses (˜0.06 dpa) during the irradiation. M23C6 carbides were found to be stable up to 5.4 dpa. Lattice defects consisted mostly of stacking fault tetrahedras (SFTs), 1/2 perfect loops and small 1/3 faulted Frank loops. The ratio of SFT number density to loop number density for each irradiation condition was found to be neither temperature nor dose dependent. Under the operation of the ion beam the SFT production was very rapid, with no evidence for further growth once formed, indicating that they probably formed as a result of cascade collapse in a single cascade. The number density of the defects was found to saturate at low dose (˜0.68 dpa). No cavities were observed regardless of the irradiation temperature between 60 °C and 400 °C for doses up to 5.4 dpa. In contrast, cavities have been observed after neutron irradiation in the same material at similar doses and temperatures indicating that helium, produce during neutron irradiation, may be essential for the nucleation and growth of cavities.

  16. Tuning the surface properties of hydrogel at the nanoscale with focused ion irradiation.

    Science.gov (United States)

    Kim, Y; Abuelfilat, A Y; Hoo, S P; Al-Abboodi, A; Liu, B; Ng, Tuck; Chan, P; Fu, J

    2014-11-14

    With the site-specific machining capability of Focused Ion Beam (FIB) irradiation, we aim to tailor the surface morphology and physical attributes of biocompatible hydrogel at the nano/micro scale particularly for tissue engineering and other biomedical studies. Thin films of Gtn-HPA/CMC-Tyr hydrogels were deposited on a gold-coated substrate and were subjected to irradiation with a kiloelectronvolt (keV) gallium ion beam. The sputtering yield, surface morphology and mechanical property changes were investigated using Scanning Electron Microscopy (SEM), Atomic Force Microscopy (AFM) and Monte Carlo simulations. The sputtering yield of the hydrogel was found to be approximately 0.47 μm(3) nC(-1) compared with Monte-Carlo simulation results of 0.09 μm(3) nC(-1). Compared to the surface roughness of the pristine hydrogel at approximately 2 nm, the average surface roughness significantly increased with the increase of ion fluence with measurements extended to 20 nm at 100 pC μm(-2). Highly packed submicron porous patterns were also revealed with AFM, while significantly decreased pore sizes and increased porosity were found with ion irradiation at oblique incidence. The Young's modulus of irradiated hydrogel determined using AFM force spectroscopy was revealed to be dependent on ion fluence. Compared to the original Young's modulus value of 20 MPa, irradiation elevated the value to 250 MPa and 350 MPa at 1 pC μm(-2) and 100 pC μm(-2), respectively. Cell culture studies confirmed that the irradiated hydrogel samples were biocompatible, and the generated nanoscale patterns remained stable under physiological conditions.

  17. Effect of Heavy Ion Head Irradiation on Immune System Function in Rat

    Institute of Scientific and Technical Information of China (English)

    YU; Ying-qi; WANG; Xiao; SUI; Li; KONG; Fu-quan; LEI; Run-hong; MA; Hong; DENG; Yu-lin; LI; Qiang

    2013-01-01

    Heavy ion radiation is a great threat to astronaut’s health.While as the most promising cancer radiotherapy,the effect of heavy ion brain radiation on immune system function in the relevant research is rare.So the brain injury model that rats were subjected to 15 Gy of head irradiation was built.By detecting lymphocyte percentage,thymus,spleen,body weight and different developmental stages of

  18. Thermal cycling and high power density hydrogen ion beam irradiation of tungsten layers on tungsten substrate

    Science.gov (United States)

    Airapetov, A. A.; Begrambekov, L. B.; Gretskaya, I. Yu; Grunin, A. V.; Dyachenko, M. Yu; Puntakov, N. A.; Sadovskiy, Ya A.

    2016-09-01

    Tungsten layers with iron impurity were deposited on tungsten substrates modeling re-deposited layers in a fusion device. The samples were tested by thermocycling and hydrogen ion beam tests. Thermocycling revealed globule formation on the surface. The size of the globules depended on iron impurity content in the coating deposited. Pore formation was observed which in some cases lead to exfoliation of the coatings. Hydrogen ion irradiation lead to formation of blisters on the coating and finally its exfoliation.

  19. Preparation of Al–Sb semiconductor by swift heavy ion irradiation

    Indian Academy of Sciences (India)

    R K Mangal; M Singh; Y K Vijay; D K Avasthi

    2006-12-01

    Al–Sb bilayer thin films having various thicknesses were deposited by thermal evaporation on ITO-coated conducting glass substrates at a pressure of 10-5 torr. These films were irradiated by Ag12+ heavy ions of energy, 160 MeV, with a fluence of 2.2 × 1013 ions/cm2, to get aluminum antimonide semiconductor. Rutherford back scattering and optical band gap data confirmed mixing of bilayer to form the semi-conducting system.

  20. Irradiation of plexiglas with heavy Gev ions: a study of destruction products

    Energy Technology Data Exchange (ETDEWEB)

    Fink, D. [Hahn-Meitner-Institut Berlin GmbH (Germany); Moeckel, H.J. [Hahn-Meitner-Institut Berlin GmbH (Germany); Melzer, H. [Hahn-Meitner-Institut Berlin GmbH (Germany); Klett, R. [Hahn-Meitner-Institut Berlin GmbH (Germany); Cardoso, J. [Univ. Autonoma Metropolitana-Iztapalapa, Mexico (Mexico). Dept. de Fisica; Montiel, R. [Univ. Autonoma Metropolitana-Iztapalapa, Mexico (Mexico). Dept. de Fisica; Vazquez, H. [Univ. Autonoma Metropolitana-Iztapalapa, Mexico (Mexico). Dept. de Fisica; Hosoi, F. [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment; Omichi, H. [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment; Wang, L. [Gesellschaft fuer Schwerionenforschung mbH, Darmstadt (Germany); Chadderton, L.T. [Australian National Univ., Canberra, ACT (Australia). Research School of Physical Sciences]|[CSIRO, Canberra, ACT (Australia). Div. of Appl. Phys.

    1997-01-01

    Examinations were performed on GeV-ion irradiated plexiglas. The radiochemical reaction products are studied by FTIR and UV spectrometry as a function of their depth of origin, and some of the possible radiochemical reaction mechanisms are examined in detail. The radiochemistry of commercial plexiglas is found to differ somewhat from the one of pure PMMA. No hint for ion-induced buckminsterfullerene formation could be found. (orig.). With 7 figs., 1 tab.

  1. Polyetheretherketone (PEEK) surface functionalization by low-energy ion-beam irradiation under a reactive O2 environment and its effect on the PEEK/copper adhesives.

    Science.gov (United States)

    Kim, Sehyun; Lee, Ki-Jun; Seo, Yongsok

    2004-01-06

    A low-energy Ar+ ion beam was used to modify the surface of a polyetheretherketone (PEEK) film. The modification reaction proceeded with or without oxygen gas injected during the irradiation. The surface functional groups of the modified PEEK were confirmed with X-ray photoelectron spectroscopy as increasing various oxygen-containing functional groups. The concentration of the functional groups varied rapidly with the irradiation time, reached a maximum value, and then slowly decreased. The surface morphology of PEEK was substantially changed by ion-beam irradiation. Surface smoothening occurred so that the surface roughness reached almost constant value after some irradiation time. The incorporation of functional groups on the PEEK surface and the surface topology change had opposite effects on the adhesion strength between PEEK and copper. Dominance of the former was evident because the lap-shear strength initially increased with the irradiation. The special surface features significantly enhanced the adhesion strength between the evaporated copper layer and the modified PEEK surface. However, the decrease in the surface roughness with a long time irradiation implies a decrease in adhesion strength due to a smaller contact area, and the shear strength due to topology change also slowly decreased after a long time irradiation.

  2. Low power test of IHQ linac for heavy ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Ito, Takashi; Sasa, Kimikazu; Hayashizaki, Noriyosu; Isokawa, Katsushi; Hattori, Toshiyuki [Tokyo Inst. of Tech. (Japan). Research Lab. for Nuclear Reactors; Osvath, E.; Schubert, H.

    1997-12-31

    At Tokyo Institute of Technology (TIT), An Interdigital-H type Quadrupole (IHQ) linac has been constructed for application of high energy heavy ion implantation. The linac can accelerate the particles with charge to mass ratio grater than 1/16 from 0.48 MeV up to 1.6 MeV (for {sup 16}O{sup +}). As a result of the low power test, the resonant frequency is 36.26 MHz and the shunt impedance is 252 M{Omega}/m. Therefore, required power to accelerate {sup 16}O{sup +} ion is 39.5 kW. (author)

  3. Microstructure and Cs Behavior of Ba-Doped Aluminosilicate Pollucite Irradiated with F+ Ions

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Weilin; Kovarik, Libor; Zhu, Zihua; Varga, Tamas; Engelhard, Mark H.; Bowden, Mark E.; Nenoff, Tina M.; Garino, Terry

    2014-06-24

    Radionuclide 137Cs is one of the major fission products that dominate heat generation in spent fuels over the first 300 hundred years. A durable waste form for 137Cs that decays to 137Ba is needed to minimize its environmental impact. Aluminosilicate pollucite CsAlSi2O6 is selected as a model waste form to study the decay-induced structural effects. While Ba-containing precipitates are not present in charge-balanced Cs0.9Ba0.05AlSi2O6, they are found in Cs0.9Ba0.1AlSi2O6 and identified as monoclinic Ba2Si3O8. Pollucite is susceptible to electron irradiation induced amorphization. The threshold density of the electronic energy deposition for amorphization is determined to be ~235 keV/nm3. Pollucite can be readily amorphized under F+ ion irradiation at 673 K. A significant amount of Cs diffusion and release from the amorphized pollucite is observed during the irradiation. However, cesium is immobile in the crystalline structure under He+ ion irradiation at room temperature. The critical temperature for amorphization is not higher than 873 K under F+ ion irradiation. If kept at or above 873 K all the time, the pollucite structure is unlikely to be amorphized; Cs diffusion and release are improbable. A general discussion regarding pollucite as a potential waste form is provided in this report.

  4. Characterization the microstructure and defects of matrix graphite irradiated with Xe ions

    Science.gov (United States)

    Xu, H. X.; Lin, J.; Li, J. J.; Zhu, Z. Y.; Zeng, G. L.; Liu, J. D.; Gu, B. C.; Liu, B.

    2017-09-01

    The matrix graphite of pebble fuel elements was irradiated with 1 MeV Xe ions at room temperature to fluences of 5.8 × 1014 ions/cm2 and 2.9 × 1015 ions/cm2, respectively. The microstructure and defects of matrix graphite samples were characterized by using scanning electron microscopy (SEM), Raman spectroscopy and slow positron beam techniques. The SEM result reveals that hundred-nanometer sized pores appear at the surface after irradiation and the density of pore increases with fluence. Raman results show that D peak (1350 cm-1) and G peak (1580 cm-1) are broadened after irradiation. In addition, the G peak position shifts from 1580 cm-1 to 1560 cm-1 with the linewidth increases from 21 cm-1 to 132 cm-1, corresponding to the increase in bond-angle disorder as the matrix graphite transforms from microcrystalline to amorphous carbon(a-C). The slow positron beam study shows that the defects-trapped positron S parameter increases with fluence, suggesting that the vacancy-type defects concentration or size of open volume defects increases. The analysis of Raman and slow positron beam consistently conclude that the reason for the phase transition after irradiation is the increase in irradiation-induced vacancy defects accompanied by the overlap of disordered regions.

  5. Impact of high dose Kr+ ion irradiation on the corrosion behavior and microstructure of Zircaloy-4

    Institute of Scientific and Technical Information of China (English)

    Qian Wan; Xinde Bai; Xiaoyang Liu

    2005-01-01

    In order to investigate the ion irradiation effect on the corrosion behavior and microstructure of Zircaloy-4, the Zircaloy-4 film were prepared by electron beam deposition on the Zircaloy-4 specimen surface and irradiated by Kr ions using an accelerator at an energy of 300 keV with the dose from 1×1015 to 3×1016ions/cm2. The post-irradiation corrosion tests were conducted to rank the corrosion resistance of the resulting specimens by potentiodynamic polarization curve measurements in a 0.5 mol/L H2SO4 water solution at room temperature. Transmission electron microscopy (TEM) was employed to examine the microstructural change in the surface. The potentiodynamic tests show that with the irradiation dose increasing, the passive current density, closely related to the surface corrosion resistance, decreases firstly and increases subsequently. The mechanism of the corrosion behavior transformation is due to the amorphous phase formation firstly and the amorphous phase destruction and the polycrystalline structure formation in the irradiated surface subsequently.

  6. Study of optical properties of swift heavy ion irradiated gallium antimonide

    Energy Technology Data Exchange (ETDEWEB)

    Dubey, S.K. [Department of Physics, University of Mumbai, Vidyanagari Campus, Santacruz (E), Mumbai 400 098 (India)]. E-mail: skdubey@physics.mu.ac.in; Dubey, R.L. [Department of Physics, University of Mumbai, Vidyanagari Campus, Santacruz (E), Mumbai 400 098 (India); Yadav, A.D. [Department of Physics, University of Mumbai, Vidyanagari Campus, Santacruz (E), Mumbai 400 098 (India); Jadhav, V. [Department of Physics, University of Mumbai, Vidyanagari Campus, Santacruz (E), Mumbai 400 098 (India); Rao, T.K. Gundu [Regional Sophisticated Instrumentation Centre, IIT Bombay, Mumbai 400 076 (India); Mohanty, T. [Nuclear Science Centre, New Delhi 110 067 (India); Kanjilal, D. [Nuclear Science Centre, New Delhi 110 067 (India)

    2006-03-15

    Gallium antimonide (GaSb) which is a narrow band gap compound semiconductor has received attention because of its potential applications in optoelectronic devices. In the present work, p-type GaSb wafers of <1 0 0> orientation were irradiated with 70 MeV {sup 56}Fe ions at fluences varying from 1 x 10{sup 12} to 1 x 10{sup 14} ions cm{sup -2}. Mid-infrared and Far-infrared Fourier Transform (FT) measurements were carried out to investigate the optical properties of as irradiated and vacuum annealed samples. Mid-infrared Fourier Transform study revealed that the optical absorption of the irradiated samples increases with increasing ion fluence due to increase in irradiation-induced defects. The band gap energy determined from the infrared spectra was found to change from 0.65 to 0.62 eV while for non-irradiated GaSb wafer the corresponding estimate was 0.67 eV. The density of the carrier estimated from the plasma frequency ({omega} {sub p}) was found to vary from 2.05 x 10{sup 18} to 1.9 x 10{sup 18} cm{sup -3}. The samples annealed in vacuum (10{sup -6} mb) over the temperature range 100-600 deg. C showed the significant damage recovery.

  7. Electric properties of undoped hydrogenated amorphous silicon semiconductors irradiated with self-ions

    Energy Technology Data Exchange (ETDEWEB)

    Sato, Shin-ichiro, E-mail: sato.shinichiro@jaea.go.jp [Japan Atomic Energy Agency (JAEA), 1233 Watanuki, Takasaki, Gunma 370-1292 (Japan); Sai, Hitoshi [National Institute of Advanced Industrial Science and Technology (AIST), 1-1-1 Umezono, Tsukuba, Ibaraki 305-8568 (Japan); Ohshima, Takeshi [Japan Atomic Energy Agency (JAEA), 1233 Watanuki, Takasaki, Gunma 370-1292 (Japan); Imaizumi, Mitsuru; Shimazaki, Kazunori [Japan Aerospace Exploration Agency (JAXA), 2-1-1 Sengen, Tsukuba, Ibaraki 305-8505 (Japan); Kondo, Michio [National Institute of Advanced Industrial Science and Technology (AIST), 1-1-1 Umezono, Tsukuba, Ibaraki 305-8568 (Japan)

    2012-08-15

    This paper reports dark conductivity (DC), photoconductivity (PC), and Seebeck coefficient variations of undoped hydrogenated amorphous silicon semiconductors irradiated with protons and Si ions. Both the DC and PC values show nonmonotonic variations with increasing a fluence in the case of proton irradiation, whereas the monotonic decreases are observed in the case of Si ion irradiation. From results of the Seebeck coefficient variation due to proton irradiation, it is shown that the increase in DC and PC in the low fluence regime is caused by donor-center generation. Also, it is shown by analyzing the proton energy dependence and the energy deposition process that the donor-center generation is based on the electronic excitation effect. On the other hand, the decrease in DC and PC in the high fluence regime is attributed to the carrier removal effect and the carrier lifetime decrease due to the accumulation of dangling bonds, respectively. The dangling bond generation due to ion irradiation is mainly caused by the displacement damage effect and therefore it is different from the generation process in the Staebler-Wronski effect.

  8. Effects of swift heavy ion irradiation on dielectric relaxation and conduction mechanism in Ba{sub 0.90}Sr{sub 0.10}TiO{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Mohan, C.R.K.; Dey, Ranajit; Patel, Shiv P.; Pandey, R.K.; Sharma, M.P.; Bajpai, P.K., E-mail: bajpai.pk1@gmail.com

    2016-04-01

    Highlights: • Paper demonstrates that high energy ion beams can be used to tune the bulk properties in polar dielectrics. • Impedance analysis inferred the resistive grain boundaries after irradiation. - Abstract: The effects of 100 MeV O{sup 8+} ion beam irradiation on the structural and dielectric behavior of Ba{sub 0.90}Sr{sub 0.10}TiO{sub 3} ceramics have been analyzed. Ion irradiation does not change the crystalline structure, however the tetragonal distortion increases. The low frequency dielectric dispersion especially at high temperatures increases significantly after ion irradiation. The dielectric relaxation phenomenon has been probed through complex impedance and electric modulus approaches. The observed dielectric relaxation has distributed relaxation times and is a thermally activated process. Ion irradiation enhances the cationic disordering. The contributions of grains and grains boundaries towards impedance have been separated. It is inferred that the grain boundaries become more resistive due to ion irradiation and is associated to oxygen vacancies annihilation. Ion irradiation also decreases the bulk ferroelectric polarization demonstrating that the surface or near surface modifications may tune the bulk properties in polar dielectrics.

  9. TEM in situ micropillar compression tests of ion irradiated oxide dispersion strengthened alloy

    Science.gov (United States)

    Yano, K. H.; Swenson, M. J.; Wu, Y.; Wharry, J. P.

    2017-01-01

    The growing role of charged particle irradiation in the evaluation of nuclear reactor candidate materials requires the development of novel methods to assess mechanical properties in near-surface irradiation damage layers just a few micrometers thick. In situ transmission electron microscopic (TEM) mechanical testing is one such promising method. In this work, microcompression pillars are fabricated from a Fe2+ ion irradiated bulk specimen of a model Fe-9%Cr oxide dispersion strengthened (ODS) alloy. Yield strengths measured directly from TEM in situ compression tests are within expected values, and are consistent with predictions based on the irradiated microstructure. Measured elastic modulus values, once adjusted for the amount of deformation and deflection in the base material, are also within the expected range. A pillar size effect is only observed in samples with minimum dimension ≤100 nm due to the low inter-obstacle spacing in the as received and irradiated material. TEM in situ micropillar compression tests hold great promise for quantitatively determining mechanical properties of shallow ion-irradiated layers.

  10. Nanopore Creation in Graphene by Ion Beam Irradiation: Geometry, Quality, and Efficiency.

    Science.gov (United States)

    Bai, Zhitong; Zhang, Lin; Li, Hengyang; Liu, Ling

    2016-09-21

    Ion beam irradiation is a promising approach to fabricate nanoporous graphene for various applications, including DNA sequencing, water desalination, and phase separation. Further advancement of this approach and rational design of experiments all require improved mechanistic understanding of the physical drilling process. Here, we demonstrate that, by using oblique ion beam irradiation, the nanopore family is significantly expanded to include more types of nanopores of tunable geometries. With the hopping, sweeping, and shoving mechanisms, ions sputter carbon atoms even outside the ion impact zone, leading to extended damage particularly at smaller incident angles. Moreover, with lower energies, ions may be absorbed to form complex ion-carbon structures, making the graphene warped or curly at pore edges. Considering both efficiency and quality, the optimal ion energy is identified to be 1000 eV at an incident angle of 30° with respect to the graphene sheet and 400-500 eV at higher incident angles. All of these results suggest the use of oblique ion beam and moderate energy levels to efficiently fabricate high-quality nanopores of tunable geometries in graphene for a wide range of applications.

  11. Probability of divacancy trap production in silicon diodes exposed to focused ion beam irradiation

    Science.gov (United States)

    Pastuović, Željko; Vittone, Ettore; Capan, Ivana; Jakšić, Milko

    2011-02-01

    We present ion beam induced charge (IBIC) measurements of the critical displacement damage dose Dd values and modeling of the probability of divacancy trap production in p+-n-n+ silicon diodes exposed to megaelectron volt energy ion beam irradiation. The normalized induced charge (Q0/Q) measured by He ion probe in tested silicon diodes irradiated by focused He, Li, O, and Cl ion beams with energies of about 0.3 MeV/u increases linearly with Dd according to the modified radiation damage function and nonionizing energy loss (NIEL) theory. A simple IBIC model based on Gunn theorem showed clear dependence of the induced charge Q and corresponding equivalent damage factor Ked value on both a depth profile of charge created by ionizing particle (probe) and a depth distribution of stable defects created from primary defects produced by damaging ions. The average probability of the divacancy production (defined as the ratio of the final electrical active defect quantity and primary ion induced vacancy quantity for each impinging ion) of 0.18 (18%) was calculated by the IBIC modeling for all damaging ions.

  12. A comparison of lower and higher LET heavy ion irradiation effects on silicon NPN rf power transistors

    Science.gov (United States)

    Bharathi, M. N.; Pushpa, N.; Vinayakprasanna, N. H.; Prakash, A. P. Gnana

    2016-06-01

    The Silicon NPN rf power transistors were irradiated with 180 MeV Au14+ and 150 MeV Ag12+ ions in the dose range of 1 Mrad to 100 Mrad. The SRIM simulation was used to understand the energy loss and range of these ions in the transistor structure. The different electrical parameters such as Gummel characteristics, excess base current (∆IB), dc current gain (hFE), transconductance (gm), displacement damage factor (K) and output characteristics were studied systematically before and after irradiation. These results were compared with lower linear energy transfer (LET) ions such as 50 MeV Li3+, 95 MeV O7+, 100 MeV F8+, 140 MeV Si10+ and 175 MeV Ni13+ ions in the same dose range. The degradation for 180 MeV Au14+ and 150 MeV Ag12+ ion irradiated transistors was significantly more when compared to lower LET ions, indicating that the transistors are vulnerable to higher LET ion irradiations. Isochronal annealing study was conducted on the irradiated transistors to analyze the recovery in different electrical parameters. After isochronal annealing, the recovery in hFE and other electrical parameters was around 67% for Ag12+ ion irradiated transistors and 60% for Au14+ ion irradiated transistors.

  13. Phenomenological understanding of dewetting and embedding of noble metal nanoparticles in thin films induced by ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Prakash, Jai, E-mail: jai.gupta1983@gmail.com [Department of Chemistry, MMH College (Ch. Charan Singh University Meerut), Ghaiziabad 201001 (India); Chemical Physics of Materials, Université Libre de Bruxelles, Campus de la Plaine, CP 243, B-1050 Bruxelles (Belgium); Tripathi, A. [Inter University Accelerator Centre, Aruna Asif Ali Marg, New Delhi 110067 (India); Gautam, Sanjeev; Chae, K.H.; Song, Jonghan [Advanced Analysis Center, Korea Institute of Science and Technology, Seoul 136–791 (Korea, Republic of); Rigato, V. [INFN Laboratori Nazionali di Legnaro, Via Romea. 4, 35020 Legnaro, Padova (Italy); Tripathi, Jalaj [Department of Chemistry, MMH College (Ch. Charan Singh University Meerut), Ghaiziabad 201001 (India); Asokan, K. [Inter University Accelerator Centre, Aruna Asif Ali Marg, New Delhi 110067 (India)

    2014-10-15

    The present experimental work provides the phenomenological approach to understand the dewetting in thin noble metal films with subsequent formation of nanoparticles (NPs) and embedding of NPs induced by ion irradiation. Au/polyethyleneterepthlate (PET) bilayers were irradiated with 150 keV Ar ions at varying fluences and were studied using scanning electron microscopy (SEM) and cross-sectional transmission electron microscopy (X-TEM). Thin Au film begins to dewet from the substrate after irradiation and subsequent irradiation results in spherical nanoparticles on the surface that at a fluence of 5 × 10{sup 16} ions/cm{sup 2} become embedded into the substrate. In addition to dewetting in thin films, synthesis and embedding of metal NPs by ion irradiation, the present article explores fundamental thermodynamic principles that govern these events systematically under the effect of irradiation. The results are explained on the basis of ion induced sputtering, thermal spike inducing local melting and of thermodynamic driving forces by minimization of the system free energy where contributions of surface and interfacial energies are considered with subsequent ion induced viscous flow in substrate. - Highlights: • Phenomenological interpretation of dewetting and embedding of metal NPs in thin film. • Exploring fundamental thermodynamic principles under influence of ion irradiation. • Ion induced surface/interface microstructural changes using SEM/X-TEM. • Ion induced sputtering, thermal spike induced local melting. • Thermodynamic driving forces relate to surface and interfacial energies.

  14. Irradiation effects on c-axis lattice parameter in EuBa{sub 2}Cu{sub 3}O{sub y} irradiated with energetic ions

    Energy Technology Data Exchange (ETDEWEB)

    Ishikawa, Norito; Chimi, Yasuhiro; Iwase, Akihiro; Maeta, Hiroshi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Tsuru, Koji; Michikami, Osamu

    1997-03-01

    We report an irradiation effect on c-axis lattice parameter in EuBa{sub 2}Cu{sub 3}O{sub y} oxide superconductors when irradiated with ions of energy ranging from 0.85 to 200 MeV. For the irradiation with low energy (0.85-2 MeV) ions, the defect production and the resultant c-axis lattice expansion were dominated by elastic collisions. On the other hand, for the irradiation with high energy (120-200 MeV) ions, the change in the c-axis lattice parameter was found to be much greater than that expected from the elastic displacement of target atoms. For high energy ion irradiation we could observe the excessive increase of c-axis lattice parameter reflecting additional production of defects which can be attributed to the electronic excitation. The large increase in c-axis lattice parameter due to high energy ion irradiation should be taken into account for the study on the interaction between vortices and irradiation-induced defects. (author)

  15. Fabrication of high aspect ratio nanocell lattices by ion beam irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Ishikawa, Osamu [School of Environmental Science and Technology, Kochi University of Technology, Tosayamada, Kami, Kochi 782-8502 (Japan); Nitta, Noriko, E-mail: nitta.noriko@kochi-tech.ac.jp [School of Environmental Science and Technology, Kochi University of Technology, Tosayamada, Kami, Kochi 782-8502 (Japan); Center for Nanotechnology, Research Institute, Kochi University of Technology, Tosayamada, Kami, Kochi 782-8502 (Japan); Taniwaki, Masafumi [School of Environmental Science and Technology, Kochi University of Technology, Tosayamada, Kami, Kochi 782-8502 (Japan)

    2016-11-01

    Highlights: • Nanocell lattice with a high aspect ratio on InSb semiconductor surface was fabricated by ion beam irradiation. • The fabrication technique consisting of top-down and bottom-up processes was performed in FIB. • High aspect ratio of 2 was achieved in nanocell lattice with a 100 nm interval. • The intermediate-flux irradiation is favorable for fabrication of nanocell with a high aspect ratio. - Abstract: A high aspect ratio nanocell lattice was fabricated on the InSb semiconductor surface using the migration of point defects induced by ion beam irradiation. The fabrication technique consisting of the top-down (formation of voids and holes) and bottom-up (growth of voids and holes into nanocells) processes was performed using a focused ion beam (FIB) system. A cell aspect ratio of 2 (cell height/cell diameter) was achieved for the nanocell lattice with a 100 nm dot interval The intermediate-flux ion irradiation during the bottom-up process was found to be optimal for the fabrication of a high aspect ratio nanocell.

  16. Microstructural response of InGaN to swift heavy ion irradiation

    Science.gov (United States)

    Zhang, L. M.; Jiang, W.; Fadanelli, R. C.; Ai, W. S.; Peng, J. X.; Wang, T. S.; Zhang, C. H.

    2016-12-01

    A monocrystalline In0.18Ga0.82N film of ∼275 nm in thickness grown on a GaN/Al2O3 substrate was irradiated with 290 MeV 238U32+ ions to a fluence of 1.2 × 1012 cm-2 at room temperature. The irradiated sample was characterized using helium ion microscopy (HIM), Rutherford backscattering spectrometry under ion-channeling conditions (RBS/C), and high-resolution X-ray diffraction (HRXRD). The irradiation leads to formation of ion tracks throughout the thin In0.18Ga0.82N film and the 3.0 μm thick GaN buffer layer. The mean diameter of the tracks in In0.18Ga0.82N is ∼9 nm, as determined by HIM examination. Combination of the HIM and RBS/C data suggests that the In0.18Ga0.82N material in the track is likely to be highly disordered or fully amorphized. The irradiation induced lattice relaxation in In0.18Ga0.82N and a distribution of d-spacing of the (0 0 0 2) planes in GaN with lattice expansion are observed by HRXRD.

  17. Molecular alteration and carbonization of aspartic acid upon N{sup +} ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Cui, F.Z. E-mail: biomater@mail.tsinghua.edu.cncuifz@sun.ihep.ac.cn; Sun, S.Q.; Zhang, D.M.; Ma, Z.L.; Chen, G.Q

    2000-06-02

    Structural changes of aspartic acid (Asp) irradiated by nitrogen ions of 30 keV were studied using Fourier transform infrared (FTIR) spectroscopy. Significant decreases of the intensities of COO{sup -}, NH{sub 3}{sup +}, COOH and CH{sub 2} vibrations in the FTIR spectra, compared with those of unirradiated Asp, were observed for the sample irradiated at the fluence of 1x10{sup 16} ions/cm{sup 2}. The decrease rates of the intensities of COO{sup -}, NH{sub 3}{sup +}, COOH and CH{sub 2} vibrations with respect to the increasing irradiation fluences up to 4x10{sup 16} ions/cm{sup 2} were different. The results were attributable to the nonstoichiometrical desorption of corresponding volatile species such as H{sub 2}, NH{sub 3}{sup +} and CO{sub 2}. The radiolysis residue of Asp after irradiation at a high fluence of 1x10{sup 17} ions/cm{sup 2} was analyzed and fatty acid was detected.

  18. Void and precipitate structure in ion- and electron-irradiated ferritic alloys

    Science.gov (United States)

    Ohnuki, Soumei; Takahashi, Heishichiro; Takeyama, Taro

    1984-05-01

    Void formation and precipitation were investigated in Fe10Cr and Fe13Cr base alloys by 200 keV C + ion and 1 MeV electron irradiation. The ferritic alloys exhibited significant resistance to void swelling. In FeCr and FeCr-Si alloys, ion-irradiation produced the precipitates of M 23C 6 type. In the FeCrTi alloy, Ti-rich precipitates were formed with high number density on {100} plane. During electron-irradiation Fe-10Cr alloy, complex dislocation loops were produced with high number density, of which Burgers vector was mostly . EDX analysis showed slightly enrichment of chromium on dislocation loops. These results suggested that the stability of type dislocation structure at high dose is an important factor on good swelling resistance in the ferritic alloys, moreover, titanium addition will intensify the stability of the doslocations through the fine precipitation on dislocations.

  19. Particle Accelerator Applications: Ion and Electron Irradiation in Materials Science, Biology and Medicine

    Science.gov (United States)

    Rodríguez-Fernández, Luis

    2010-09-01

    Although the developments of particle accelerators are devoted to basic study of matter constituents, since the beginning these machines have been applied with different purposes in many areas also. Today particle accelerators are essential instruments for science and technology. This work presents an overview of the main application for direct particle irradiation with accelerator in material science, biology and medicine. They are used for material synthesis by ion implantation and charged particle irradiation; to make coatings and micromachining; to characterize broad kind of samples by ion beam analysis techniques; as mass spectrometers for atomic isotopes determination. In biomedicine the accelerators are applied for the study of effects by charged particles on cells. In medicine the radiotherapy by electron irradiation is widely used, while hadrontherapy is still under development. Also, they are necessary for short life radioisotopes production required in radiodiagnostic.

  20. In situ observation of the ultrafast lattice dynamics of graphite under ion irradiation

    Science.gov (United States)

    Ishioka, Kunie; Hase, Muneaki; Kitajima, Masahiro

    2004-05-01

    We develop a pump-probe experiment system, in which vibrational dynamics of a solid sample under ion irradiation can be measured in real time. In situ observation enables us to monitor small changes induced by ion irradiation, without being influenced by the irreproducibility of the sample quality or the experimental configuration. We apply the experimental system to investigate the femtosecond dynamics of the coherent E2 g1 phonon of graphite under 5 keV He + irradiation. A slight decrease in the dephasing rate of the phonon at the initial stage, as well as a downshift followed by an upshift of the phonon frequency, are clearly demonstrated, all of which were ambiguous in the ex situ experiment due to the poor reproducibility of the surface quality. This technique could also be applied to study femtosecond vibrational dynamics in real time during thermal annealing, film deposition with e.g. ablation and sputter, and molecular adsorption on substrates.

  1. Enhanced Load Transfer in Carbon Nanotube Bundles via Carbon-Ion Bombardment

    Science.gov (United States)

    Carpena-Nunez, Jennifer; Hernandez, Jose A.; Siochi, Emilie J.; Kim, Jae-Woo; Fonseca, Luis F.

    2014-03-01

    Carbon Nanotubes (CNTs) are ideal candidates for structural composites due to their high modulus and strength, and low weight and density. However, achieving their exceptional mechanical performance at the macroscale is an ongoing challenge, as individual CNTs within bundles are held together by weak van der Waals forces. The current work aims to address issues related to crosslinking CNTs via carbon-ion irradiation to achieve the mechanical performance promised by CNTs. Samples irradiated with a carbon-ion dose of ~ 1013-1014 cm-2 and kinetic energies ranging from 9-25keV show partial amorphization at the outermost layer of the CNT bundle, as theoretically predicted. Mechanical data collected via in-situ Transmission Electron Microscopy-Atomic Force Microscopy (TEM-AFM) shows an increase in tensile and shear strength for irradiated CNT bundles of ~ 6.6GPa and ~ 100MPa, respectively. The adhesion energy between CNT bundles showed an increase from ~ 0.12-0.48 Jm-2 for pristine CNTs up to ~ 42 Jm-2 for carbon-ion irradiated bundles. In addition, enhanced shear interaction exceeding a strength value of ~ 1GPa was observed when exposed to additional amorphous carbon binding, providing a route for improved adhesion to polymer components used in structural composites. This work was supported by a NASA Space Technology Research Fellowship.

  2. Morphological change of self-organized protrusions of fluoropolymer surface by ion beam irradiation

    Science.gov (United States)

    Kitamura (Ogawa), Akane; Kobayashi, Tomohiro; Satoh, Takahiro; Koka, Masashi; Kamiya, Tomihiro; Suzuki, Akihiro; Terai, Takayuki

    2013-07-01

    Polytetrafluoroethylene (PTFE) and fluorinated ethylene propylene (FEP) are typical fluoropolymers displaying several desirable technological properties such as electrical insulation and high chemical resistance. When their surfaces are irradiated with ion beams, dense micro-protrusions formed after the emergence and spread of micropores across the entire irradiated area, allowing culture cells to spread on the top of the protrusions. In this study, we investigate the morphological changes introduced in the fluoropolymer surfaces by ion beams as the energy of the beams is increased. When an FEP sample was irradiated with a nitrogen ion beam with an energy of less than 350 keV at 1.0 μA/cm2, protrusions were formed with a density between 2 × 107/cm2 and 2 × 108/cm2. However, at energies higher than 350 keV, the protrusions became sparse, and the density dropped to 5 × 102/cm2. Protrusions appeared sporadically during irradiation at high energies, and the top of the protrusions appeared as spots inside the sample, which were difficult to etch and became elongated as the erosion of the surface progressed. Erosion was caused by sputtering of FEP molecules and evaporation at notably elevated temperatures on the surface. Analysis based on attenuated total reflectance/Fourier transform infrared spectroscopy showed the presence of Cdbnd C bonds as well as -COOH, -Cdbnd O, and -OH bonds on all irradiated samples. Their concentration on the surface densely covered with micro-protrusions was higher than that on the surface with sparse protrusions after irradiation at energies exceeding 350 keV. Thus, we determined a suitable range for the ion energy for creating FEP surfaces densely covered with protrusions.

  3. Morphological change of self-organized protrusions of fluoropolymer surface by ion beam irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Kitamura, Akane, E-mail: ogawa.akane@jaea.go.jp [Department of Advanced Radiation Technology, Takasaki Advanced Radiation Research Institute, Japan Atomic Energy Agency, 1233 Watanuki-machi, Takasaki, Gunma 370-1292 (Japan); Kobayashi, Tomohiro [Advanced Science Institute, RIKEN, 2-1 Hirosawa, Wako-shi, Saitama 350-0198 (Japan); Satoh, Takahiro; Koka, Masashi; Kamiya, Tomihiro [Department of Advanced Radiation Technology, Takasaki Advanced Radiation Research Institute, Japan Atomic Energy Agency, 1233 Watanuki-machi, Takasaki, Gunma 370-1292 (Japan); Suzuki, Akihiro; Terai, Takayuki [Department of Nuclear Engineering and Management, School of Engineering, The University of Tokyo, 2-11-16 Yayoi, Bunkyo-ku, Tokyo 113-8656 (Japan)

    2013-07-15

    Polytetrafluoroethylene (PTFE) and fluorinated ethylene propylene (FEP) are typical fluoropolymers displaying several desirable technological properties such as electrical insulation and high chemical resistance. When their surfaces are irradiated with ion beams, dense micro-protrusions formed after the emergence and spread of micropores across the entire irradiated area, allowing culture cells to spread on the top of the protrusions. In this study, we investigate the morphological changes introduced in the fluoropolymer surfaces by ion beams as the energy of the beams is increased. When an FEP sample was irradiated with a nitrogen ion beam with an energy of less than 350 keV at 1.0 μA/cm{sup 2}, protrusions were formed with a density between 2 × 10{sup 7}/cm{sup 2} and 2 × 10{sup 8}/cm{sup 2}. However, at energies higher than 350 keV, the protrusions became sparse, and the density dropped to 5 × 10{sup 2}/cm{sup 2}. Protrusions appeared sporadically during irradiation at high energies, and the top of the protrusions appeared as spots inside the sample, which were difficult to etch and became elongated as the erosion of the surface progressed. Erosion was caused by sputtering of FEP molecules and evaporation at notably elevated temperatures on the surface. Analysis based on attenuated total reflectance/Fourier transform infrared spectroscopy showed the presence of C=C bonds as well as –COOH, –C=O, and –OH bonds on all irradiated samples. Their concentration on the surface densely covered with micro-protrusions was higher than that on the surface with sparse protrusions after irradiation at energies exceeding 350 keV. Thus, we determined a suitable range for the ion energy for creating FEP surfaces densely covered with protrusions.

  4. Irradiation effects in polycarbonate induced by 2.1 GeV Kr ions

    Institute of Scientific and Technical Information of China (English)

    TIAN Hui-Xian; JIN Yun-Fan; ZHU Zhi-Yong; SUN You-Mei; WANG Zhi-Guang

    2003-01-01

    Polycarbonate foil stacks were irradiated with 2.1 GeV Kr ions under vacuum at room temperature.The modifications in chemical structure induced by the irradiation were studied by means of Fourier transform infra-red (FTIR) and ultraviolet visible (UV/VIS) spectroscopies. FTIR measurements reveal that material degradationsthrough bond breaking are the main effects. Alkyne end groups are produced by the irradiation. UV/VIS measure-ments indicate a shifting of the absorption edge from ultraviolet towards visible, and a strong increase of absorbancein the ultraviolet and visible regions. The changes in absorbance induced by the irradiation at wavelengths of 380 nm,450 nm and 500 nm scale well with Sne (Se is electronic energy loss) where the value of n increases from 1.69 to 2.02with increasing of the wavelength. The results are briefly discussed.

  5. Ion irradiation and biomolecular radiation damage II. Indirect effect

    CERN Document Server

    Wang, Wei; Su, Wenhui

    2010-01-01

    It has been reported that damage of genome in a living cell by ionizing radiation is about one-third direct and two-thirds indirect. The former which has been introduced in our last paper, concerns direct energy deposition and ionizing reactions in the biomolecules; the latter results from radiation induced reactive species (mainly radicals) in the medium (mainly water) surrounding the biomolecules. In this review, a short description of ion implantation induced radical formation in water is presented. Then we summarize the aqueous radical reaction chemistry of DNA, protein and their components, followed by a brief introduction of biomolecular damage induced by secondary particles (ions and electron). Some downstream biological effects are also discussed.

  6. Influence of Kilo-Electron Oxygen Ion Irradiation on Structural, Electrical and Optical Properties of CdTe Thin Films

    Science.gov (United States)

    Honey, Shehla; Thema, F. T.; Bhatti, M. T.; Ishaq, A.; Naseem, Shahzad; Maaza, M.

    2016-09-01

    In this paper, effect of oxygen (O+) ion irradiation on the properties of polycrystalline cubic structure CdTe thin films has been investigated. CdTe thin films were irradiated with O+ ions of energy 80keV at different fluence ranging from 1×1015 to 5×1016 ion/cm2 at room temperature. At 1×1015 ion/cm2 O+ ions fluence, the CdTe structure was maintained while XRD peaks of cubic phase were shifted toward lower angles. At 5×1016 ion/cm2 O+ ions fluence, cubic structure of CdTe thin films was transformed into hexagonal structure. In addition, electrical resistivity and optical bandgap were decreased with increasing O+ ion beam irradiation.

  7. Optical Properties of Ar Ions Irradiated Nanocrystalline ZrC and ZrN Thin Films

    Science.gov (United States)

    Martin, C.; Miller, K. H.; Makino, H.; Craciun, D.; Simeone, D.; Craciun, V.

    2016-01-01

    Thin nanocrystalline ZrC and ZrN films (less than 400 nanometers), grown on (100) Si substrates at a substrate temperature of 500 degrees Centigrade by the pulsed laser deposition (PLD) technique, were irradiated by 800 kiloelectronvolts Ar ion irradiation with fluences from 1 times 10(sup 14) atoms per square centimeter up to 2 times 10(sup 15) atoms per square centimeter. Optical reflectance data, acquired from as-deposited and irradiated films, in the range of 500-50000 per centimeter (0.06–6 electronvolts), was used to assess the effect of irradiation on the optical and electronic properties. Both in ZrC and ZrN films we observed that irradiation affects the optical properties of the films mostly at low frequencies, which is dominated by the free carriers response. In both materials, we found a significant reduction in the free carriers scattering rate, i.e. possible increase in mobility, at higher irradiation flux. This is consistent with our previous findings that irradiation affects the crystallite size and the micro-strain, but it does not induce major structural changes.

  8. Enhanced photocatalytic performance of BiVO4 in aqueous AgNO3 solution under visible light irradiation

    Science.gov (United States)

    Huang, Chien-Kai; Wu, Tsunghsueh; Huang, Chang-Wei; Lai, Chi-Yung; Wu, Mei-Yao; Lin, Yang-Wei

    2017-03-01

    Monoclinic-phase bismuth vanadate (BiVO4) with a 2.468 eV band gap exhibited enhanced synergic photodegradation activity toward methylene blue (MB) when combined with silver ions (Ag+) in an aqueous solution under visible light irradiation. The mass ratio of AgNO3 to BiVO4 and the calcination temperature were discovered to considerably affect the degradation activity of BiVO4/Ag+. Superior photocatalytic performance was obtained when BiVO4 was mixed with 0.01%(w/v) AgNO3 solution, and complete degradation of MB was achieved after 25 min visible light irradiation, outperforming BiVO4 or AgNO3 solution alone. The enhanced photodegradation was investigated using systematic luminescence measurements, electrochemical impedance spectroscopy, and scavenger addition, after which a photocatalytic mechanism for MB degradation under visible light irradiation was identified that involved oxygen radicals and holes. This study also discovered the two dominating processes involved in enhancing the electron-hole separation efficiency and reducing their recombination rate, namely photoreduction of Ag+ and the formation of a BiVO4/Ag heterojunction. The synergic effect between BiVO4 and Ag+ was discovered to be unique. BiVO4/Ag+ was successfully used to degrade two other dyes and disinfect Escherichia Coli. A unique fluorescent technique using BiVO4 and a R6G solution to detect Ag+ ions in water was discovered.

  9. Microstructure of Swift Heavy Ion Irradiated MgAl(Sub 2)O(Sub 4) Spinel

    Energy Technology Data Exchange (ETDEWEB)

    Matzke, H.; Skuratov, V.A.; Zinkle, S.J.

    1998-11-30

    Plan view and cross-section transmission electron microscopy was used to investigate the microstructure of magnesium aluminate spinel (MgAl{sub 2}O{sub 4}) following room temperature irradiation with either 430 MeV Kr, 614 MeV Xe, or 72 MeV I ions. The fluences ranged from 1 x 10{sup 16}/m{sup 2} (single track regime) to 1 x 10{sup 20}/m{sup 2}. Destruction of the ordered spinel crystal structure on both the anion and cation sublattices was observed in the ion tracks at low fluences. At intermediate fluences, the overlapping ion tracks induced the formation of a new metastable crystalline phase. Amorphization with a volumetric expansion of {approximately}35% was observed in spinel irradiated with swift heavy ions (electronic stopping powers >7 keV/nm) at fluences above 1 x 10{sup 19}/m{sup 2}. These results demonstrate that swift heavy ion radiation can induce microstructural changes not achievable with conventional elastic collision irradiation at comparable temperatures.

  10. Mixing induced by swift heavy ion irradiation at Fe/Si interface

    Indian Academy of Sciences (India)

    Veenu Sisodia; I P Jain

    2004-08-01

    The present work deals with the mixing of metal and silicon by swift heavy ions in high-energy range. Threshold value for the defect creation in metal Fe calculated was found to be ∼ 40 keV/nm. A thin film of Fe (10 nm) was deposited on Si (100) at a pressure of 4 × 10-8 Torr and was irradiated with 95 MeV Au ions. Irradiation was done at RT, to a dose of 1013 ions/cm2 and 1 pna current. The electronic energy loss was found to be 29.23 keV/nm for 95 MeV Au ions in Fe using TRIM calculation. Compositional analysis of samples was done by Rutherford backscattering spectroscopy. Reflectivity studies were carried out on the pre-annealed and post-annealed samples to study irradiation effects. Grazing incidence X-ray diffraction was done to study the interface. It was observed that ion beam mixing reactions at RT lead to mixing as a result of high electronic excitations.

  11. Anisotropic proton-conducting membranes prepared from swift heavy ion-beam irradiated ETFE films

    Energy Technology Data Exchange (ETDEWEB)

    Kimura, Yosuke [Department of Chemistry, Faculty of Engineering, Gunma University, 1-5-1 Tenjin-cho, Kiryu, Gunma 376-8515 (Japan); Chen Jinhua [Environment and Industrial Materials Research Division, Quantum Beam Science Directorate, Japan Atomic Energy Agency (JAEA), 1233 Watanuki-machi, Takasaki, Gunma 370-1292 (Japan)], E-mail: chen.jinhua@jaea.go.jp; Asano, Masaharu; Maekawa, Yasunari [Environment and Industrial Materials Research Division, Quantum Beam Science Directorate, Japan Atomic Energy Agency (JAEA), 1233 Watanuki-machi, Takasaki, Gunma 370-1292 (Japan); Katakai, Ryoichi [Department of Chemistry, Faculty of Engineering, Gunma University, 1-5-1 Tenjin-cho, Kiryu, Gunma 376-8515 (Japan); Yoshida, Masaru [Environment and Industrial Materials Research Division, Quantum Beam Science Directorate, Japan Atomic Energy Agency (JAEA), 1233 Watanuki-machi, Takasaki, Gunma 370-1292 (Japan)

    2007-10-15

    Poly(ethylene-co-tetrafluoroethylene) (ETFE) films were irradiated by swift heavy ion-beams of {sup 129}Xe{sup 23+} with fluences of 0, 3 x 10{sup 6}, 3 x 10{sup 7}, 3 x 10{sup 8} and 3 x 10{sup 9} ions/cm{sup 2}, followed by {gamma}-ray pre-irradiation for radiation grafting of styrene onto the ETFE films and sulfonation of the grafted ETFE films to prepare highly anisotropic proton-conducting membranes. The fluence of Xe ions and the addition of water in the grafting solvent were examined to determine their effect on the proton conductivity of the resultant membranes. It was found that the polymer electrolyte membrane prepared by grafting the styrene monomer in a mixture of 67% isopropanol and 33% water to the ETFE film with an ion-beam irradiation fluence of 3.0 x 10{sup 6} ions/cm{sup 2} was a highly anisotropic proton-conducting material, as the proton conductivity was three or more times higher in the thickness direction than in the surface direction of the membrane.

  12. Protease-mediated enhancement of lymphocyte-induced angiogenesis in X-ray irradiated mice

    Energy Technology Data Exchange (ETDEWEB)

    Kaminski, M.J.; Majewski, S.; Kaminska, G.; Bem, W.; Szmurlo, A. (Akademia Medyczna, Warsaw (Poland). Zaklad Histologii i Embriologii)

    1983-02-01

    Angiogenesis was induced in mice by intradermal injection of semi-syngeneic splenocytes, and after three days the number of newly formed blood vessels at the injection site was counted. When recipients were total-body irradiated with 700 R 2 hours before the lymphocyte injection, the angiogenesis was significantly higher than in non-irradiated mice. The angiogenesis enhancement was of a systemic (not local) character as revealed in experiments with shielding of irradiated animals. This enhancement was not due to X-ray dependent immunosuppression, as shown in experiments with non-irradiated, pharmacologically immunosuppressed mice. Decreased angiogenesis was observed in irradiated mice after treatment with cortisone acetate, aprotinin, and EACA. The results suggest that proteases might be involved in mediating the angiogenesis enhancement after X-irradiation.

  13. Ion irradiation effects on SrCeO sub 3 thin films

    CERN Document Server

    Matsunami, N; Iwahara, H; Sata, N; Ishigame, M

    2002-01-01

    Ion irradiation effects on a proton conductive oxide, i.e. SrCe sub 0 sub . sub 9 sub 5 Yb sub 0 sub . sub 0 sub 5 O sub 3 sub - subdelta (SCO) have been investigated by measurements of sputtering yield, modifications of compositions and structure. The sputtering yields of SCO by 100 keV Ar sup + and Ne sup + are determined as 1.6 and 0.55 atoms per ion, respectively. The compositions remain nearly stoichiometric under ion irradiation. The experimental sputtering yields are compared with those of computer simulations based on the elastic-collision cascade and the surface-binding energies for sputtering, dependent on the simulation version, are deduced. These values are compared with those derived from the thermodynamic properties. The elastic collisions appear to be dominant.

  14. Investigating change of properties in gallium ion irradiation patterned single-layer graphene

    Science.gov (United States)

    Wang, Quan; Dong, Jinyao; Bai, Bing; Xie, Guoxin

    2016-10-01

    Besides its excellent physical properties, graphene promises to play a significant role in electronics with superior properties, which requires patterning of graphene for device integration. Here, we presented the changes in properties of single-layer graphene before and after patterning using gallium ion beam. Combined with Raman spectra of graphene, the scanning capacitance microscopy (SCM) image confirmed that a metal-insulator transition occurred after large doses of gallium ion irradiation. The changes in work function and Raman spectra of graphene indicated that the defect density increased as increasing the dose and a structural transition occurred during gallium ion irradiation. The patterning width of graphene presented an increasing trend due to the scattering influence of the impurities and the substrate.

  15. Physical and chemical response of 70 MeV carbon ion irradiated Kapton-H polymer

    Indian Academy of Sciences (India)

    H S Virk; P S Chandi; A K Srivastava

    2001-10-01

    Physical and chemical responses of 70 MeV carbon ion irradiated Kapton-H polymer were studied by using UV-visible, FTIR and XRD techniques. The ion fluences ranging from 9.3 × 1011–9 × 1013 ions cm–2 were used. Recorded UV-visible spectra clearly showed a decrease in absorption initially with fluence, but for the higher fluences it showed a recovery characteristic. A decrease in band-gap energy of 0.07 eV was observed. The FTIR analysis indicated the high resistance to radiation induced degradation of polymer. The diffraction pattern of Kapton-H indicates that this polymer is semi-crystalline in its nature. In case of irradiated one, there was an average increase of crystallite size by 20%, but diffuse pattern indicates that there was a decrease in crystallinity, which may be attributed to the formation of complex structure induced by the cross-linking of the polymeric chains.

  16. Surface modifications caused by a swift heavy ion irradiation on crystalline p-type gallium antimonide

    Energy Technology Data Exchange (ETDEWEB)

    Jadhav, Vidya, E-mail: vj1510@yahoo.com

    2015-09-01

    Surface modifications caused by a swift heavy ion irradiation on crystalline p-type gallium antimonide crystal have been reported. Single crystal, 1 0 0〉 orientations and ∼500 μm thick p-type GaSb samples with carrier concentration of 3.30 × 10{sup 17} cm{sup −3} were irradiated at 100 MeV Fe{sup 7+} ions. We have used 15UD Pelletron facilities at IUAC with varying fluences of 5 × 10{sup 10}–1 × 10{sup 14} ions cm{sup −2}. The effects of irradiation on these samples have been investigated using, spectroscopic ellipsometry, atomic force microscopy and ultraviolet–visible–NIR spectroscopy techniques. Ellipsometry parameters, psi (Ψ) and delta (Δ) for the unirradiated sample and samples irradiated with different fluences were recorded. The data were fit to a three phase model to determine the refractive index and extinction coefficient. The refractive index and extinction coefficient for various fluences in ultraviolet, visible, and infrared, regimes were evaluated. Atomic force microscopy has been used to study these surface modifications. In order to have more statistical information about the surface, we have plotted the height structure histogram for all the samples. For unirradiated sample, we observed the Gaussian fitting. This result indicates the more ordered height structure symmetry. Whereas for the sample irradiated with the fluence of 1 × 10{sup 13}, 5 × 10{sup 13} and 1 × 10{sup 14} ions cm{sup −2}, we observed the scattered data. The width of the histogram for samples irradiated up to the fluence of 1 × 10{sup 13} ion cm{sup −2} was found to be almost same however it decreased at higher fluence. UV reflectance spectra of the sample irradiated with increasing fluences exhibit three peaks at 292, 500 and 617 nm represent the high energy GaSb; E{sub 1}, E{sub 1} + Δ and E{sub 2} band gaps in all irradiated samples.

  17. Molecular dynamics simulation analysis of ion irradiation effects on plasma-liquid interface

    Science.gov (United States)

    Minagawa, Yudai; Shirai, Naoki; Uchida, Satoshi; Tochikubo, Fumiyoshi

    2013-09-01

    Nonthermal atmospheric plasmas are used in a wide range of fields because the high-density plasma can be easily irradiated to various substances such as solid, liquid, biological object and so on. On the other hand, the mechanisms of physical and chemical phenomena at the plasma-liquid interface are not well understood yet. To investigate the effects of ion impact from plasma on water surface, we analyzed behavior of liquid water by classical molecular dynamics simulation. Simulation system consists of an irradiation particle in gas phase and 2000 water molecules in liquid phase. O+ ion with 10 eV or 100 eV was impinged on the water surface. Ion impact induced increasing water temperature and ejection of water molecules. The averaged number of evaporated water molecules by ion impact is 0.6 molecules at 10 eV and 7.0 molecules at 100 eV. The maximum ion penetration depth was 1.14 nm at 10 eV and 2.75 nm at 100 eV. Ion entering into water disturbs the stable hydrogen bonding configurations between water molecules and gives energy to water molecules. Some water molecules rotated and moved by ion interaction impact on other water molecules one after another. When the water molecule near the surface received strongly repulsive force, it released into gas phase. This work was supported financially in part by a Grant-in-Aid for Scientific Research on Innovation Areas (No21110007) from MEXT, Japan.

  18. Hot, metastable hydronium ion in the Galactic centre: formation pumping in X-ray-irradiated gas?

    Science.gov (United States)

    Lis, Dariusz C; Schilke, Peter; Bergin, Edwin A; Emprechtinger, Martin

    2012-11-13

    With a 3.5 m diameter telescope passively cooled to approximately 80 K, and a science payload comprising two direct detection cameras/medium resolution imaging spectrometers (PACS and SPIRE) and a very high spectral resolution heterodyne spectrometer (HIFI), the Herschel Space Observatory is providing extraordinary observational opportunities in the 55-670 μm spectral range. HIFI has opened for the first time to high-resolution spectroscopy the submillimetre band that includes the fundamental rotational transitions of interstellar hydrides, the basic building blocks of astrochemistry. We discuss a recent HIFI discovery of metastable rotational transitions of the hydronium ion (protonated water, H(3)O(+)), with rotational level energies up to 1200 K above the ground state, in absorption towards Sagittarius B2(N) in the Galactic centre. Hydronium is an important molecular ion in the oxygen chemical network. Earlier HIFI observations have indicated a general deficiency of H(3)O(+) in the diffuse gas in the Galactic disc. The presence of hot H(3)O(+) towards Sagittarius B2(N) thus appears to be related to the unique physical conditions in the central molecular zone, manifested, for example, by the widespread presence of abundant H(3)(+). One intriguing theory for the high rotational temperature characterizing the population of the H(3)O(+) metastable levels may be formation pumping in molecular gas irradiated by X-rays emitted by the Galactic centre black hole. Alternatively, the pervasive presence of enhanced turbulence in the central molecular zone may give rise to shocks in the lower-density medium that is exposed to energetic radiation.

  19. Irradiation of Fe-Mn Supersaturated Solid Solution with Ions of Various Atomic Masses (Ar+, Xe+) and Analysis of the Role of Nanosized Dynamic Effects in the Activation Processes of Long-Range Type

    Science.gov (United States)

    Ovchinnikov, V. V.; Makhin'ko, F. F.; Semionkin, V. A.; Shalomov, K. V.

    2017-05-01

    A multiple increase in the atom mobility in metastable supersaturated (quenched from 850 °C) Fe-8.16 at % Mn solid solution is detected at temperatures less than 250°C under irradiation with 5-keV Ar+ and Xe+ ions of different masses. The irradiation-induced atom redistribution in the entire volume of foils 30 μm thick at a projected Ar+ and Xe+ ion ranges as much as 20-30 nm only is found and studied by the transmission Mössbauer spectroscopy. Long-range effects at low irradiation doses and anomalously low temperatures are attributed to “radiation shaking” of metastable media with post-cascade solitary waves in contrast to thermally stimulated radiation-enhanced processes in the narrow nanoscale near-surface layers of the alloy. It has been shown that heavier Xe+ ions at higher irradiation doses have a stronger impact on the solid solution than Ar+ ions.

  20. Enhanced lipid productivity and photosynthesis efficiency in a Desmodesmus sp. mutant induced by heavy carbon ions.

    Science.gov (United States)

    Hu, Guangrong; Fan, Yong; Zhang, Lei; Yuan, Cheng; Wang, Jufang; Li, Wenjian; Hu, Qiang; Li, Fuli

    2013-01-01

    The unicellular green microalga Desmodesmus sp. S1 can produce more than 50% total lipid of cell dry weight under high light and nitrogen-limitation conditions. After irradiation by heavy (12)C(6+) ion beam of 10, 30, 60, 90 or 120 Gy, followed by screening of resulting mutants on 24-well microplates, more than 500 mutants were obtained. One of those, named D90G-19, exhibited lipid productivity of 0.298 g L(-1)⋅d(-1), 20.6% higher than wild type, likely owing to an improved maximum quantum efficiency (Fv/Fm) of photosynthesis under stress. This work demonstrated that heavy-ion irradiation combined with high-throughput screening is an effective means for trait improvement. The resulting mutant D90G-19 may be used for enhanced lipid production.

  1. Enhanced lipid productivity and photosynthesis efficiency in a Desmodesmus sp. mutant induced by heavy carbon ions.

    Directory of Open Access Journals (Sweden)

    Guangrong Hu

    Full Text Available The unicellular green microalga Desmodesmus sp. S1 can produce more than 50% total lipid of cell dry weight under high light and nitrogen-limitation conditions. After irradiation by heavy (12C(6+ ion beam of 10, 30, 60, 90 or 120 Gy, followed by screening of resulting mutants on 24-well microplates, more than 500 mutants were obtained. One of those, named D90G-19, exhibited lipid productivity of 0.298 g L(-1⋅d(-1, 20.6% higher than wild type, likely owing to an improved maximum quantum efficiency (Fv/Fm of photosynthesis under stress. This work demonstrated that heavy-ion irradiation combined with high-throughput screening is an effective means for trait improvement. The resulting mutant D90G-19 may be used for enhanced lipid production.

  2. ENHANCING FOOD SAFETY AND STABILITY THROUGH IRRADIATION: A REVIEW

    Directory of Open Access Journals (Sweden)

    Manzoor Ahmad Shah

    2014-04-01

    Full Text Available Food irradiation is one of the non thermal food processing methods. It is the process of exposing food materials to the controlled amounts of ionizing radiations such as gamma rays, X-rays and accelerated electrons, to improve microbiological safety and stability. Irradiation disrupts the biological processes that lead to decay of food quality. It is an effective tool to reduce food-borne pathogens, spoilage microorganisms and parasites; to extend shelf-life and for insect disinfection. The safety and consumption of irradiated foods have been extensively studied at national levels and in international cooperations and have concluded that foods irradiated under appropriate technologies are both safe and nutritionally adequate. Specific applications of food irradiation have been approved by national legislations of more than 55 countries worldwide. This review aims to discuss the applications of irradiation in food processing with the emphasis on food safety and stability.

  3. In situ observation of surface morphology evolution in tungsten under focused Ga{sup +} ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Ran Guang, E-mail: gran@umich.edu [School of Energy Research, Xiamen University, Xiamen, Fujian 361005 (China); Department of Nuclear Engineering and Radiological Sciences, University of Michigan, Ann Arbor, MI 48109 (United States); Liu Xiang; Wu Jihong [Southwestern Institute of Physics, Chengdu, Sichuan 610041 (China); Li Ning [School of Energy Research, Xiamen University, Xiamen, Fujian 361005 (China); Zu Xiaotao [Department of Applied Physics, University of Electronic Science and Technology of China, Chengdu, Sichuan 610054 (China); Wang Lumin, E-mail: lmwang@umich.edu [School of Energy Research, Xiamen University, Xiamen, Fujian 361005 (China); Department of Nuclear Engineering and Radiological Sciences, University of Michigan, Ann Arbor, MI 48109 (United States); Department of Materials Science and Engineering, University of Michigan, Ann Arbor, MI 48109 (United States)

    2012-05-15

    The effects of energetic Ga ion bombardment on the surface morphology of mechanically polished polycrystalline tungsten are investigated by focused Ga{sup +} ion beam irradiation with in situ scanning electron microscopy, as well as ex situ atomic force microscopy. The amount of removed material from the tungsten surface increased with increasing of incident ion angle, and also increased with ion energy from 5 to 30 keV while keeping all other bombardment parameters constant. The nanoneedle-shaped morphology formed by self-assembly in the surface of tungsten under off-normal angle bombardment, the larger the incident angle, the easier for the needle formation. In contrast, only a net-like microstructure formed under normal incident angle. Moreover, more Ga{sup +} ion fluence was needed to form pores at normal incident angle comparing to that under 52 Degree-Sign incident angle.

  4. DLTS study of deep level defects in Li-ion irradiated bipolar junction transistor

    Science.gov (United States)

    Madhu, K. V.; Kulkarni, S. R.; Ravindra, M.; Damle, R.

    2007-01-01

    Commercial npn transistor (2N 2219A) irradiated with 50 MeV Li 3+-ions with fluences ranging from 3.1 × 10 13 ions cm -2 to 12.5 × 10 13 ions cm -2, is studied for radiation induced gain degradation and minority carrier trap levels or recombination centers. The properties such as activation energy, trap concentration and capture cross section of induced deep levels are studied by deep level transient spectroscopy (DLTS) technique. Minority carrier trap levels with energies ranging from 0.237 eV to 0.591 eV were observed in the base-collector junction of the transistor. In situ I- V measurements were made to study the gain degradation as a function of ion fluence. Ion induced energy levels result in increase in the base current through Shockley Read Hall (SRH) or multi-phonon recombination and subsequent transistor gain degradation.

  5. Effect of Ni7+ Ion Irradiation on Structure and Ammonia Sensing Properties of Thermally Oxidized Zinc and Indium Films

    Institute of Scientific and Technical Information of China (English)

    Amandeep Kaur Bal; Rafinder Singh; R.K. Bedi

    2012-01-01

    ZnO and In203 films were prepared by thermal oxidation of vacuum deposited zinc and indium films, respec- tively onto the glass substrate at 30 ℃. The fabricated films have been irradiated with 100-MeV Ni7+ ions at different fluences ranging from 5×1011 to 5×1013 ions/cm2. The structural and gas sensing properties of pristine and irradiated films have been discussed. X-ray diffraction (XRD) pattern of pristine and irradiated films reveal that the films are polycrystalline in nature and crystallinity increases after irradiation. In this study, highly porous In203 nanorods evolved when being irradiated at a fluence of 5×1013 ions/cm2 while ZnO film shows decrease in number of nanowires. The ammonia sensing performance of the Ni^7+ irradiated In203 films shows an improvement as compared to its pristine counterpart.

  6. Mechanical response of UO{sub 2} single crystals submitted to low-energy ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Nguyen, Tien-Hien [Centre de Sciences Nucléaires et de Sciences de la Matière (CSNSM), Univ. Paris-Sud – CNRS/IN2P3, Université Paris-Saclay, Bâtiment 108, 91405 Orsay Cedex (France); Department of Physics, Vietnam National University of Agriculture, Trau Quy, Gia Lam, Hanoi (Viet Nam); Debelle, Aurélien, E-mail: aurelien.debelle@u-psud.fr [Centre de Sciences Nucléaires et de Sciences de la Matière (CSNSM), Univ. Paris-Sud – CNRS/IN2P3, Université Paris-Saclay, Bâtiment 108, 91405 Orsay Cedex (France); Boulle, Alexandre [Science des Procédés Céramiques et de Traitements de Surface CNRS UMR 7315, Centre Européen de la Céramique, 12 rue Atlantis, 87068 Limoges (France); Garrido, Frédérico; Thomé, Lionel [Centre de Sciences Nucléaires et de Sciences de la Matière (CSNSM), Univ. Paris-Sud – CNRS/IN2P3, Université Paris-Saclay, Bâtiment 108, 91405 Orsay Cedex (France); Demange, Valérie [Institut des Sciences Chimiques de Rennes, CNRS UMR 6226, 263 avenue du Général Leclerc, Campus de Beaulieu – Bâtiment 10B, 35042 Rennes Cedex (France)

    2015-12-15

    {111}- and {100}-oriented UO{sub 2} single crystals were irradiated with 500-keV Ce{sup 3+} ions in the 10{sup 14}–9 × 10{sup 14} cm{sup −2} fluence range. The irradiation-induced strain was monitored using high-resolution X-ray diffraction. A mechanical modelling dedicated to thin irradiated layers was applied to account for the reaction of the unirradiated part of the crystals. The elastic strain, which is confined along the surface normal of the samples, increases with ion fluence until it is dramatically relieved. This behaviour is observed for both orientations. While the measured elastic strain depends on the crystallographic direction, the strain due to irradiation defects only is found to be equal for both directions, with a maximum value of ∼0.5%. Strain relaxation takes place at the damage peak, but the in-plane lattice parameter of the irradiated layer remains unchanged and equal to that of the pristine material. Meanwhile, the strain at the damaged/pristine interface continues to increase.

  7. Evidence of amorphisation of B4C boron carbide under slow, heavy ion irradiation

    Science.gov (United States)

    Gosset, D.; Miro, S.; Doriot, S.; Victor, G.; Motte, V.

    2015-12-01

    Boron carbide is widely used either as armor-plate or neutron absorber. In both cases, a good structural stability is required. However, a few studies have shown amorphisation may occur in severe conditions. Hard impacts lead to the formation of amorphous bands. Some irradiations in electronic regime with H or He ions have also shown amorphisation of the material. Most authors however consider the structure is not drastically affected by irradiations in the ballistic regime. Here, we have irradiated at room temperature dense boron carbide pellets with Au 4 MeV ions, for which most of the damage is in the ballistic regime. This study is part of a program devoted to the behavior of boron carbide under irradiation. Raman observations have been performed after the irradiations together with transmission electron microscopy (TEM). Raman observations show a strong structural damage at moderate fluences (1014/cm2, about 0.1 dpa), in agreement with previous studies. On the other hand, TEM shows the structure remains crystalline up to 1015/cm2 then partially amorphises. The amorphisation is heterogeneous, with the formation of nanometric amorphous zones with increasing density. It then appears short range and long range disorder occurs at quite different damage levels. Further experiments are in progress aiming at studying the structural stability of boron carbide and isostructural materials (α-B, B6Si,…).

  8. Gold wetting effects on sapphire irradiated with GeV uranium ions

    Energy Technology Data Exchange (ETDEWEB)

    Ramos, S.M.M. [Universite Claude Bernard, Villeurbanne (France). Dept. de Phys. des Mater.; Canut, B. [Universite Claude Bernard, Villeurbanne (France). Dept. de Phys. des Mater.; Fornazero, J. [Universite Claude Bernard, Villeurbanne (France). Dept. de Phys. des Mater.; Thevenard, P. [Universite Claude Bernard, Villeurbanne (France). Dept. de Phys. des Mater.; Toulemonde, M. [Centre Interdisciplinaire de Recherche avec les Ions Lourds (CIRIL), Boulevard A. Becquerel, 14040 Caen Cedex (France)

    1997-02-01

    Single crystals of {alpha}-Al{sub 2}O{sub 3} were irradiated with {sup 238}U ions using two different energies: 3.4 MeV/u and 1.7 MeV/u. The irradiations were performed at a temperature of {approx}80 K, with fluences ranging from 1.2 x 10{sup 12} to 2.5 x 10{sup 12} ions cm{sup -2}. After irradiation, thin gold films were deposited on the sapphire surfaces by using a sputtering method. Subsequent annealing in air at a temperature of 723 and 923 K were applied to investigate the influence of the pre-damage on the adhesion of the gold layer on the sapphire surface. Rutherford backscattering analysis and scanning electron microscopy performed in both virgin and irradiated areas, show that the pre-irradiation damage inhibits the gold film of breaking up into islands after annealing. A wetting effect, which could depend on the damage morphology, is clearly observed. (orig.).

  9. Microstructure evolution and degradation mechanisms of reactor internal steel irradiated with heavy ions

    Science.gov (United States)

    Borodin, O. V.; Bryk, V. V.; Kalchenko, A. S.; Parkhomenko, A. A.; Shilyaev, B. A.; Tolstolutskaya, G. D.; Voyevodin, V. N.

    2009-03-01

    Structure evolution and degradation mechanisms during irradiation of 18Cr-10Ni-Ti steel (material of VVER-1000 reactor internals are investigated). Using accelerator irradiations with Cr3+ and Ar+ ions allowed studying effects of dose rate, different initial structure state and implanted ions on features of structure evolution and main mechanisms of degradation including low temperature swelling and embrittlement of the 18Cr-10Ni-Ti steel. It is shown that differences in dose rate at most irradiation temperatures mainly exert their influence on the duration of the swelling transient regime. Calculations of possible transmutation products during irradiation of this steel in a VVER-1000 spectrum were performed. It is shown that gaseous atoms (He and H), which are generated simultaneously with radiation defects, stabilize the elements of radiation microstructure and influence the swelling. The nature of deformation under different temperatures of irradiation and of mechanical testing is investigated. It is shown that the temperature sensitivity of swelling behaviour in the investigated steel, with different initial structures can be connected with the dynamic behaviour of point defect sinks.

  10. Surface morphology and microstructure evolution of IG-110 graphite after xenon ion irradiation and subsequent annealing

    Science.gov (United States)

    Huang, Qing; Li, Jianjian; Liu, Renduo; Yan, Long; Huang, Hefei

    2017-08-01

    IG-110 graphite samples were polished and irradiated with Xe ions at various fluences, then annealed at high temperatures up to 1100 °C. After irradiation, small hills were found on the polished surfaces, indicating an anisotropic swelling induced by irradiation. Around 30% swelling at a fluence of 2 × 1015 ions/cm2 was characterized using atomic force microscopy. Severe swelling of the graphite crystallites caused stresses between adjacent crystallites, but leaved no intergranular cracks on the polished surface, which was ascribed to irradiation-induced creep of graphite. The pore morphology was affected by the anisotropic swelling. We found many contracted pores but only one expanded pore, indicating a decreased porosity induced by irradiation. After annealing at 1100 °C, TEM characterization showed clearly increased lattice order and decreased width of the (002) diffraction arc, indicating the annihilation of dislocations and recovery of basal plane rotations. Annealing-induced recrystallization of damaged graphite led to recovery of the crystallites' swelling and many small cracks appearing on the samples' surfaces.

  11. Effects of high energy Au-ion irradiation on the microstructure of diamond films

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Shih-Show [Department of Physics, Tamkang University, Tamsui, New-Taipei 251, Taiwan (China); Department of Information Technology and Mobile Communication, Taipei College of Maritime Technology, Tamsui, New-Taipei 251, Taiwan (China); Chen, Huang-Chin [Department of Physics, Tamkang University, Tamsui, New-Taipei 251, Taiwan (China); Department of Materials Science and Engineering, National Tsing Hua University, Hsinchu 300, Taiwan (China); Wang, Wei-Cheng; Lin, I-Nan; Chang, Ching-Lin [Department of Physics, Tamkang University, Tamsui, New-Taipei 251, Taiwan (China); Lee, Chi-Young [Department of Materials Science and Engineering, National Tsing Hua University, Hsinchu 300, Taiwan (China); Guo Jinghua [Advanced Light Source, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States)

    2013-03-21

    The effects of 2.245 GeV Au-ion irradiation and subsequent annealing processes on the evolution of microstructure of diamond films with microcrystalline (MCD) or ultra-nanocrystalline (UNCD) granular structure were investigated, using near edge x-ray absorption fine structure and electron energy loss spectroscopy in transmission electron microscopy. For MCD films, the Au-ion irradiation disintegrated some of the diamond grains, resulting in the formation of nano-sized carbon clusters embedded in a matrix of amorphous carbon (a-C). The annealing process recrystallized the diamond grains and converted the a-C into nano-sized graphite particulates and, at the same time, induced the formation of nano-sized i-carbon clusters, the bcc structured carbon with a{sub 0} = 0.432 nm. In contrast, for UNCD films, the Au-ion irradiation transformed the grain boundary phase into nano-sized graphite, but insignificantly altered the crystallinity of the grains of the UNCD films. The annealing process recrystallized the materials. In some of the regions, the residual a-C phases were transformed into nano-sized graphites, whereas in other regions i-carbon nanoclusters were formed. The difference in irradiation-induced microstructural transformation behavior between the MCD and the UNCD films is ascribed to the different granular structures of the two types of films.

  12. Influence of ion species ratio on grid-enhanced plasma source ion implantation

    Institute of Scientific and Technical Information of China (English)

    Wang Jiu-Li; Zhang Gu-Ling; Liu Yuan-Fu; Wang You-Nian; Liu Chi-Zi; Yang Si-Ze

    2004-01-01

    @@ Grid-enhanced plasma source ion implantation (GEPSII) is a newly proposed technique to modify the inner-surface properties of a cylindrical bore. In this paper, a two-ion fluid model describing nitrogen molecular ions N2+ and atomic ions N+ is used to investigate the ion sheath dynamics between the grid electrode and the inner surface of a cylindrical bore during the GEPSII process, which is an extension of our previous calculations in which only N2+ was considered.Calculations are concentrated on the results of ion dose and impact energy on the target for different ion species ratios in the core plasma. The calculated results show that more atomic ions N+ in the core plasma can raise the ion impact energy and reduce the ion dose on the target.

  13. An analysis of 100 MeV F 8+ ion and 50 MeV Li 3+ ion irradiation effects on silicon NPN rf power transistors

    Science.gov (United States)

    Pushpa, N.; Praveen, K. C.; Gnana Prakash, A. P.; Prabhakara Rao, Y. P.; Tripati, Ambuj; Revannasiddaiah, D.

    2010-08-01

    The dc characteristics exhibited by NPN power transistors are studied systematically before and after irradiation by 100 MeV F 8+ ions and 50 MeV Li 3+ ions in the dose range of 100 krad to 100 Mrad. The transistor parameters such as excess base current (Δ IB= IBpost- IBpre), dc current gain ( hFE), transconductance ( gm), and collector-saturation current ( ICsat) were studied before and after irradiation. The damage factors ( k) for hFE were calculated for ion irradiated transistors using Messenger-Spratt relation. The base current ( IB) was found to increase significantly after ion irradiation and this in turn decreases the hFE of the transistors. The gm decreases significantly after ion irradiation. Moreover, the output characteristics of irradiated devices also show that the collector current ( IC) in the saturation region ( ICsat) decrease with increase in ion dose. The observed change in these characteristics may be due to the ion induced generation-recombination (G-R) centers in emitter-base (E-B) spacer oxide and the ion induced point defects and their complexes in the transistor structure.

  14. Hardening of ODS ferritic steels under irradiation with high-energy heavy ions

    Science.gov (United States)

    Ding, Z. N.; Zhang, C. H.; Yang, Y. T.; Song, Y.; Kimura, A.; Jang, J.

    2017-09-01

    Influence of the nanoscale oxide particles on mechanical properties and irradiation resistance of oxide-dispersion-strengthened (ODS) ferritic steels is of critical importance for the use of the material in fuel cladding or blanket components in advanced nuclear reactors. In the present work, impact of structures of oxide dispersoids on the irradiation hardening of ODS ferritic steels was studied. Specimens of three high-Cr ODS ferritic steels containing oxide dispersoids with different number density and average size were irradiated with high-energy Ni ions at about -50 °C. The energy of the incident Ni ions was varied from 12.73 MeV to 357.86 MeV by using an energy degrader at the terminal so that a plateau of atomic displacement damage (∼0.8 dpa) was produced from the near surface to a depth of 24 μm in the specimens. A nanoindentor (in constant stiffness mode with a diamond Berkovich indenter) and a Vickers micro-hardness tester were used to measure the hardeness of the specimens. The Nix-Gao model taking account of the indentation size effect (ISE) was used to fit the hardness data. It is observed that the soft substrate effect (SSE) can be diminished substantially in the irradiated specimens due to the thick damaged regions produced by the Ni ions. A linear correlation between the nano-hardeness and the micro-hardness was found. It is observed that a higher number density of oxide dispersoids with a smaller average diameter corresponds to an increased resistance to irradiation hardening, which can be ascribed to the increased sink strength of oxides/matrix interfaces to point defects. The rate equation approach and the conventional hardening model were used to analyze the influence of defect clusters on irradiation hardening in ODS ferritic steels. The numerical estimates show that the hardening caused by the interstitial type dislocation loops follows a similar trend with the experiment data.

  15. Magnetosomes extracted from Magnetospirillum magneticum strain AMB-1 showed enhanced peroxidase-like activity under visible-light irradiation.

    Science.gov (United States)

    Li, Kefeng; Chen, Chuanfang; Chen, Changyou; Wang, Yuzhan; Wei, Zhao; Pan, Weidong; Song, Tao

    2015-05-01

    Magnetosomes are intracellular structures produced by magnetotactic bacteria and are magnetic nanoparticles surrounded by a lipid bilayer membrane. Magnetosomes reportedly possess intrinsic enzyme mimetic activity similar to that found in horseradish peroxidase (HRP) and can scavenge reactive oxygen species depending on peroxidase activity. Our previous study has demonstrated the phototaxis characteristics of Magnetospirillum magneticum strain AMB-1 cells, but the mechanism is not well understood. Therefore, we studied the relationship between visible-light irradiation and peroxidase-like activity of magnetosomes extracted from M. magneticum strain AMB-1. We then compared this characteristic with that of HRP, iron ions, and naked magnetosomes using 3,3',5,5'-tetramethylbenzidine as a peroxidase substrate in the presence of H2O2. Results showed that HRP and iron ions had different activities from those of magnetosomes and naked magnetosomes when exposed to visible-light irradiation. Magnetosomes and naked magnetosomes had enhanced peroxidase-like activities under visible-light irradiation, but magnetosomes showed less affinity toward substrates than naked magnetosomes under visible-light irradiation. These results suggested that the peroxidase-like activity of magnetosomes may follow an ordered ternary mechanism rather than a ping-pong mechanism. This finding may provide new insight into the function of magnetosomes in the phototaxis in magnetotactic bacteria.

  16. Virus inactivation studies using ion beams, electron and gamma irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Smolko, Eduardo E. [Laboratorio de Polimeros, Grupo Aplicaciones Industriales, Unidad de Aplicaciones Tecnologicas y Agropecuarias, Centro Atomico Ezeiza, Comision Nacional de Energia Atomica, Pbro. Juan Gonzalez y Aragon 15, C.P. B1802AYA Ezeiza, Buenos Aires (Argentina)]. E-mail: smolko@cae.cnea.gov.ar; Lombardo, Jorge H. [Biotech S.A., C.P. 1754 Buenos Aires (Argentina)

    2005-07-01

    Known methods of virus inactivation are based on the chemical action of some substances such as acetylethylenimine, betapropiolactone, glycidalaldehyde, formaldehyde, etc. In such a process, the viral suspension should be kept at room or higher temperatures for 24-48 h. Under these conditions, physical and chemical agents act to degrade the virus antigenic proteins. On the contrary with ionizing radiations at low temperatures, the treatment does not cause such degradation allowing the study of different viral functions. In this work, particle ({alpha}, d and ss) and {gamma} irradiations were used for partial and total inactivation of Foot and Mouth Disease Virus (FMDV), Rauscher Leukemia Virus (RLV) and Herpes Simplex Virus (HSV). Obtention of the D{sub 37} dose from survival curves and the application of the target theory, permitted the determination of molecular weight of the nucleic acid genomes, EBR values and useful information for vaccine preparation. For RLV virus, a two target model of the RNA genome was deduced in accordance with biological information while from data from the literature and our own work on the structure of the scrapie prion, considering the molecular weight obtained by application of the theory, a new model for prion replication is presented, based on a trimer molecule.

  17. Virus inactivation studies using ion beams, electron and gamma irradiation

    Science.gov (United States)

    Smolko, Eduardo E.; Lombardo, Jorge H.

    2005-07-01

    Known methods of virus inactivation are based on the chemical action of some substances such as acetylethylenimine, betapropiolactone, glycidalaldehyde, formaldehyde, etc. In such a process, the viral suspension should be kept at room or higher temperatures for 24-48 h. Under these conditions, physical and chemical agents act to degrade the virus antigenic proteins. On the contrary with ionizing radiations at low temperatures, the treatment does not cause such degradation allowing the study of different viral functions. In this work, particle (α, d and ß) and γ irradiations were used for partial and total inactivation of Foot and Mouth Disease Virus (FMDV), Rauscher Leukemia Virus (RLV) and Herpes Simplex Virus (HSV). Obtention of the D37 dose from survival curves and the application of the target theory, permitted the determination of molecular weight of the nucleic acid genomes, EBR values and useful information for vaccine preparation. For RLV virus, a two target model of the RNA genome was deduced in accordance with biological information while from data from the literature and our own work on the structure of the scrapie prion, considering the molecular weight obtained by application of the theory, a new model for prion replication is presented, based on a trimer molecule.

  18. Mutation effects of C{sup 2+} ion irradiation on the greasy Nitzschia sp

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Y.N., E-mail: ynyangbuaa@gmail.com [School of Chemistry and Environment, Beihang University, 37th Xueyuan Road, Haidian District, P.O. Box 106, 100191 Beijing (China); Liu, C.L.; Wang, Y.K. [School of C