WorldWideScience

Sample records for investigation phase iv

  1. Investigation on the formation of a third phase in the extraction of Pu(IV) nitrate with tributyl phosphate

    International Nuclear Information System (INIS)

    Yu Enjiang; Liu Liming; Huang Huaian

    1986-01-01

    The formation of a third phase is studied in the system Pu(IV) nitratenitric acid-TBP-alkane diluent (or kerosine). The maximum concentration (solubility, S Pu ) of Pu(IV) in the equilibrium organic phase at which still no third phase is formed is measured as a function of the nitric acid concentration in the equilibrium aqueous phase C H , the temperature, and the molecular size of n-alkane duluent. Results show that maxima of S Pu at 6 to 7 M nitric acid are observed at 17 deg C, 26 deg C and 35 deg C while not at 40 deg C. Minima on the S Pu vs. C H curves at 0.5 to 2 M mitric acid have been observed at 17 deg C and 26 deg C. It is found that the molecular size of n-alkane diluents has a very pronounced effect on S Pu . The effect of aqueous equilibrium Pu(IV) concentration on the formation of a third phase is investigated, when the equilibrium HNO 3 concentration is 3.5 M. It is shown that the plutonium concentration of the third phase is increased with increasing aqueous equilibrium Pu(IV) concentration. The effect of the addition of lauryl alcohol on the S Pu is preliminarily studied

  2. SANS study of Th (IV) third phase formation in HNO3 / DHDECMP-n-dodecane system

    International Nuclear Information System (INIS)

    Lohithakshan, K.V.; Aggarwal, S.K.; Aswal, V.K.

    2009-01-01

    Third phase formation taking place during the extraction of Th (IV) from nitric acid medium by DHDECMP in dodecane has been investigated by small angle neutron scattering (SANS) and explained the process with Baxter model. (author)

  3. Evaluation of Market Design Programme - Phase IV; Utvaerdering av Market Designprogrammet - etapp IV

    Energy Technology Data Exchange (ETDEWEB)

    Wall, Tomas

    2013-08-15

    The Market Design program was established in year 2000 to study issues related to markets, regulations and policy instruments related to the deregulation of the Swedish electricity market. Through the years, the focus has widened to include not only Sweden but also international cooperation on these issues. The fourth phase of the program is now underway between the years 2010 and 2013. The overall project objective of this fourth phase is to increase knowledge about the Nordic and North European electricity market. Specific objective is to create new knowledge that affects market design of the single market area (Nordic, EU) and to contribute to constructive meetings between researchers, energy companies and government agencies on Market Design Issues. The purpose of the evaluation of the Market Design Program phase IV has been to investigate the results and benefits of the program in relation to the program's original objectives and to examine the need for and areas of further research and possible ways for the research in Market Design. The evaluation has been carried through in four phases during spring and summer 2013. The work has included reading, interviews with program stakeholders, analysis and reporting.

  4. Calculation of superalloy phase diagrams. IV

    International Nuclear Information System (INIS)

    Kaufman, L.; Nesor, H.

    1975-01-01

    Explicit descriptions of the Fe--Mo, Fe--W, Fe--Nb, W--Cr and Ti--W binary systems have been developed in line with lattice stability, thermochemical and phase diagram data. These descriptions, along with similar results derived previously, have been employed to calculate isothermal sections in the Cr--Al--Fe, Fe--Mo--Cr, Fe--W--Cr, Ni--Al--Co, Nb--Ti--W, Ti--W--Mo, Cr--W--Mo, Ni--Mo--W, and Ni--W--Ti systems for comparison with experimental results. The effects of carbon impurities on miscibility gap formation in the Ti--W, Nb--Ti--W, Ti--W--Mo and Cr--W--Mo systems are discussed

  5. Maqarin natural analogue project: Phase IV. Reconnaissance mission report (April 28 to May 7, 1999)

    Energy Technology Data Exchange (ETDEWEB)

    Smellie, J.A.T. [ed.] [Conterra AB, Uppsala (Sweden)

    2000-08-01

    Final planning of the Technical Proposal for Phase IV of the Maqarin Natural Analogue Project was preceded by a ten day Reconnaissance Mission to the Jordan sites. The main objective of this mission was to: i) allow new organisations within the project to become familiar with the geological context of the Maqarin and Central Jordan sites and also to appreciate the prevailing technical and logistical limitations, ii) carry out limited field investigations, and iii) based on the experience from these two points, provide the opportunity to finalise the Maqarin Phase IV Technical Proposal. This report details the results of the mission.

  6. Maqarin natural analogue project: Phase IV. Reconnaissance mission report (April 28 to May 7, 1999)

    International Nuclear Information System (INIS)

    Smellie, J.A.T.

    2000-08-01

    Final planning of the Technical Proposal for Phase IV of the Maqarin Natural Analogue Project was preceded by a ten day Reconnaissance Mission to the Jordan sites. The main objective of this mission was to: i) allow new organisations within the project to become familiar with the geological context of the Maqarin and Central Jordan sites and also to appreciate the prevailing technical and logistical limitations, ii) carry out limited field investigations, and iii) based on the experience from these two points, provide the opportunity to finalise the Maqarin Phase IV Technical Proposal. This report details the results of the mission

  7. Possible superconductivity in the Bismuth IV solid phase under pressure.

    Science.gov (United States)

    Valladares, Ariel A; Rodríguez, Isaías; Hinojosa-Romero, David; Valladares, Alexander; Valladares, Renela M

    2018-04-13

    The first successful theory of superconductivity was the one proposed by Bardeen, Cooper and Schrieffer in 1957. This breakthrough fostered a remarkable growth of the field that propitiated progress and questionings, generating alternative theories to explain specific phenomena. For example, it has been argued that Bismuth, being a semimetal with a low number of carriers, does not comply with the basic hypotheses underlying BCS and therefore a different approach should be considered. Nevertheless, in 2016 based on BCS we put forth a prediction that Bi at ambient pressure becomes a superconductor at 1.3 mK. A year later an experimental group corroborated that in fact Bi is a superconductor with a transition temperature of 0.53 mK, a result that eluded previous work. So, since Bi is superconductive in almost all the different structures and phases, the question is why Bi-IV has been elusive and has not been found yet to superconduct? Here we present a study of the electronic and vibrational properties of Bi-IV and infer its possible superconductivity using a BCS approach. We predict that if the Bi-IV phase structure were cooled down to liquid helium temperatures it would also superconduct at a T c of 4.25 K.

  8. Phase Transitions in Layered Diguanidinium Hexachlorostannate(IV)

    DEFF Research Database (Denmark)

    Szafranski, Marek; Ståhl, Kenny

    2016-01-01

    is different. The transitions involve also transformations in the networks of N-H center dot center dot center dot Cl hydrogen bonds. The large volume (similar to 3%) and entropy (similar to R ln 3) change at the transition between phases II and III, and the giant pressure coefficient of -755 K GPa(-1......Five crystalline phases of diguanidinium hexachlorostannate(IV), [C(NH2)(3)](2)SnCl6, have been identified and characterized by calorimetric and dielectric measurements, single crystal X-ray diffraction at atmospheric and high pressure, and synchrotron X-ray powder diffraction. The crystal...... structures of all phases are built of similar layers in which the tin hexachloride anions are connected to the guanidinium cations by N-H center dot center dot center dot Cl hydrogen bonds, forming a interact primarily by Coulombic forces between the ions from ap. double H-bonded sheets. The layers, neutral...

  9. A phase 3 trial of IV immunoglobulin for Alzheimer disease.

    Science.gov (United States)

    Relkin, Norman R; Thomas, Ronald G; Rissman, Robert A; Brewer, James B; Rafii, Michael S; van Dyck, Christopher H; Jack, Clifford R; Sano, Mary; Knopman, David S; Raman, Rema; Szabo, Paul; Gelmont, David M; Fritsch, Sandor; Aisen, Paul S

    2017-05-02

    We tested biweekly infusions of IV immunoglobulin (IVIg) as a possible treatment for mild to moderate Alzheimer disease (AD) dementia. In a phase 3, double-blind, placebo-controlled trial, we randomly assigned 390 participants with mild to moderate AD to receive placebo (low-dose albumin) or IVIg (Gammagard Liquid; Baxalta, Bannockburn, IL) administered IV at doses of 0.2 or 0.4 g/kg every 2 weeks for 18 months. The primary cognitive outcome was change from baseline to 18 months on the 11-item cognitive subscale of the Alzheimer's Disease Assessment Scale; the primary functional outcome was 18-month change on the Alzheimer's Disease Cooperative Study-Activities of Daily Living Inventory. Safety and tolerability data, as well as serial MRIs and plasma samples, were collected throughout the study from all enrolled participants. No beneficial effects were observed in the dual primary outcome measures for the 2 IVIg doses tested. Significant decreases in plasma Aβ42 (but not Aβ40) levels were observed in IVIg-treated participants. Analysis of safety data showed no difference between IVIg and placebo in terms of the rate of occurrence of amyloid-related imaging abnormalities (brain edema or microhemorrhage). IVIg-treated participants had more systemic reactions (chills, rashes) but fewer respiratory infections than participants receiving placebo. Participants with mild to moderate AD showed good tolerability of treatment with low-dose human IVIg for 18 months but did not show beneficial effects on cognition or function relative to participants who received placebo. NCT00818662. This study provides Class II evidence that IVIg infusions performed every 2 weeks do not improve cognition or function at 18 months in patients with mild to moderate AD. © 2017 American Academy of Neurology.

  10. Phase transitions of antibiotic clarithromycin forms I, IV and new form VII crystals.

    Science.gov (United States)

    Ito, Masataka; Shiba, Rika; Watanabe, Miteki; Iwao, Yasunori; Itai, Shigeru; Noguchi, Shuji

    2018-06-01

    Metastable crystal form I of the antibiotic clarithromycin has a pharmaceutically valuable characteristic that its crystalline phase transition can be applied for its sustained release from tablets. The phase transition of form I was investigated in detail by single crystal and powder X-ray analyses, dynamic vapor sorption analysis and thermal analysis. The single crystal structure of form I revealed that form I was not an anhydrate crystal but contained a partially occupied water molecule in the channel-like void space. Dynamic vapor sorption (DVS) analysis demonstrated that form I crystals reversibly sorbed water molecules in two steps when the relative humidity (RH) increased and finally transited to hydrate form IV at 95% RH. DVS analysis also showed that when the RH decreased form IV crystals lost water molecules at 40% RH and transited to the newly identified anhydrate crystal form VII. Form VII reversibly transited to form IV at lower RH than form I, suggesting that form I is more suitable for manufacturing a sustained-release tablet of CAM utilizing the crystalline phase transition. Copyright © 2018 Elsevier B.V. All rights reserved.

  11. Brush Day & Night Phase III to Phase IV: ensuring that good oral health habits are sustainable.

    Science.gov (United States)

    Melo, Paulo; Fine, Charlotte; Malone, Sinead; Horn, Virginie

    2018-05-01

    Over the past 10 years, the FDI-Unilever Brush Day & Night partnership has significantly influenced the life of children worldwide through the implementation of school programmes for oral health education and prevention. This article reports the key facts and outcomes of Phase III of the partnership, and announces the launch of Phase IV. During Phase III, the expert advisors of the Brush Day & Night partnership conducted a longitudinal study to evaluate the impact of the '21 Day' programme in almost 8,000 children in 10 countries. Analysis revealed the effectiveness of the 21 Day programme in sustainably educating children to brush their teeth twice a day, with the greatest impact observed in children aged 7-9 years. With the launch of Phase IV, the Brush Day & Night partnership will continue to deliver its oral health school programme for 7-9 year-old children with a strengthened methodology, including randomized sampling and control groups. The scope of the evaluation will be broadened to include oral health-related quality of life indicators, and monitoring of the oral health knowledge of children's parents/carers. © 2018 FDI World Dental Federation.

  12. Uganda Health Information Network (UHIN) - Phase IV | IDRC ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    ... reports on drug supplies and use, and continuing education materials. This phase aims to fully integrate the Network into the Ministry of Health district and national ... IWRA/IDRC webinar on climate change and adaptive water management.

  13. Lattice distortion and spontaneous Γ5g ferro-quadrupole moment in phase IV of CexLa1-xB6

    International Nuclear Information System (INIS)

    Nemoto, Yuichi; Akatsu, Mitsuhiro; Goto, Terutaka; Suzuki, Osamu; Nakamura, Shintaro; Kunii, Satoru

    2005-01-01

    We have performed low-temperature thermal expansion measurements to investigate lattice effect of the phase IV in Ce x La 1-x B 6 , for x=0.75 and 0.70. In phase IV of both compounds, lattice length along the [111] direction shrinks notably, on the other hand length along the [001] direction expands. These results provide evidence that the spontaneous Γ 5g ferro-quadrupole moment yz >= zx >= xy > 0 is relevant in phase IV because the trigonal lattice distortion is described by the symmetry strain yz >= zx >= xy > 0 simultaneously

  14. Formation of U(IV) Nanoparticles and Their Growth Mechanism in Mildly Acidic Aqueous Phases

    Energy Technology Data Exchange (ETDEWEB)

    Cha, Wan Sik; Kim, Sun Tae; Cho, Hye Ryun; Jung, Euo Chang [KAERI, Daejeon (Korea, Republic of)

    2016-05-15

    Previous studies suggest that U(IV) nanoparticle (NP) formation is one of key steps in mineralization or immobilization of uranium which can be mediated either by microbes or by abiotic geochemical reactions. Colloidal NPs in a groundwater system are potential carrier phases influencing RN migration in subsurface environment. However, the mechanism of U(IV) NP formation and the potential reaction intermediates during this solid phase formation process have not been elucidated in detail so far. In this study we attempted to examine the U(IV) nanoparticle formation reactions preceded by the hydrolysis of U{sup 4+} at different pHs, concentrations and temperatures. The kinetics of U(IV) NP formation from dissolved U(IV) species was monitored under mildly acidic conditions (pH 2 ∼ 3) mainly by using UV-Vis absorption spectrophotometry. Dynamic light scattering (DLS) analysis, nanoparticle tracking analysis (NTA) and transmission electron microscopy (TEM) were used to characterize the NPs produced during the reactions. The results demonstrate that the U(IV) NP formation process is very sensitive toward temperature variation. The main outcome of this study is the discovery of the autocatalytic nature of U(IV) NP formation from the supersaturated U(OH){sup 3+} solution in a mildly acidic aqueous solution. The structure of reaction intermediates is proposed to contain oxide linkage. In the presentation the proposed mechanism of the U(IV) NP formation reaction and the properties of primary NPs and their clusters will be discussed in detail.

  15. ILEAP Core Grant 2011-2012 - Phase IV: Engendering Inclusive ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    It does so by providing them with independent economic and legal advisory support, capacity building and knowledge networking in the form of training, briefs and background papers in response to World Trade Organization (WTO), multilateral or bilateral negotiations. Previous phases of the project (105214, 103286 and ...

  16. Trade and Industrial Policy Strategies (TIPS) Core Grant - Phase IV ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Established in 1996, Trade and Industrial Policy Strategies (TIPS) is an organization that coordinates a network of researchers that seeks to provide the Government of South Africa, civil society and the region with independent advice on economic policy, with a particular focus on trade and industrial issues. Earlier phases of ...

  17. Situational Lightning Climatologies for Central Florida: Phase IV

    Science.gov (United States)

    Bauman, William H., III

    2009-01-01

    The threat of lightning is a daily concern during the warm season in Florida. Research has revealed distinct spatial and temporal distributions of lightning occurrence that are strongly influenced by large-scale atmospheric flow regimes. Previously, the Applied Meteorology Unit (AMU) calculated the gridded lightning climatologies based on seven flow regimes over Florida for 1-, 3- and 6-hr intervals in 5-, 10-,20-, and 30-NM diameter range rings around the Shuttle Landing Facility (SLF) and eight other airfields in the National Weather Service in Melbourne (NWS MLB) county warning area (CWA). In this update to the work, the AMU recalculated the lightning climatologies for using individual lightning strike data to improve the accuracy of the climatologies. The AMU included all data regardless of flow regime as one of the stratifications, added monthly stratifications, added three years of data to the period of record and used modified flow regimes based work from the AMU's Objective Lightning Probability Forecast Tool, Phase II. The AMU made changes so the 5- and 10-NM radius range rings are consistent with the aviation forecast requirements at NWS MLB, while the 20- and 30-NM radius range rings at the SLF assist the Spaceflight Meteorology Group in making forecasts for weather Flight Rule violations during Shuttle landings. The AMU also updated the graphical user interface with the new data.

  18. Robust Requirements Tracing via Internet Search Technology: Improving an IV and V Technique. Phase 2

    Science.gov (United States)

    Hayes, Jane; Dekhtyar, Alex

    2004-01-01

    There are three major objectives to this phase of the work. (1) Improvement of Information Retrieval (IR) methods for Independent Verification and Validation (IV&V) requirements tracing. Information Retrieval methods are typically developed for very large (order of millions - tens of millions and more documents) document collections and therefore, most successfully used methods somewhat sacrifice precision and recall in order to achieve efficiency. At the same time typical IR systems treat all user queries as independent of each other and assume that relevance of documents to queries is subjective for each user. The IV&V requirements tracing problem has a much smaller data set to operate on, even for large software development projects; the set of queries is predetermined by the high-level specification document and individual requirements considered as query input to IR methods are not necessarily independent from each other. Namely, knowledge about the links for one requirement may be helpful in determining the links of another requirement. Finally, while the final decision on the exact form of the traceability matrix still belongs to the IV&V analyst, his/her decisions are much less arbitrary than those of an Internet search engine user. All this suggests that the information available to us in the framework of the IV&V tracing problem can be successfully leveraged to enhance standard IR techniques, which in turn would lead to increased recall and precision. We developed several new methods during Phase II; (2) IV&V requirements tracing IR toolkit. Based on the methods developed in Phase I and their improvements developed in Phase II, we built a toolkit of IR methods for IV&V requirements tracing. The toolkit has been integrated, at the data level, with SAIC's SuperTracePlus (STP) tool; (3) Toolkit testing. We tested the methods included in the IV&V requirements tracing IR toolkit on a number of projects.

  19. Explorations of new phases in the Ga(III)/In(III)-Mo(VI)-Se(IV)/Te(IV)-O systems.

    Science.gov (United States)

    Kong, Fang; Hu, Chun-Li; Hu, Ting; Zhou, Yong; Mao, Jiang-Gao

    2009-07-07

    Systematic explorations of new phases in the Ga(III)/In(III)-Mo(VI)-Se(IV)/Te(IV)-O systems by hydrothermal syntheses or solid-state reactions at high-temperature led to four new quaternary compounds, namely, Ga(2)MoQ(2)O(10) (Q = Se, Te), In(2)Mo(2)Se(2)O(13)(H(2)O) and In(2)MoTe(2)O(10). Ga(2)MoQ(2)O(10) (Q = Se, Te) are isostructural and their structures feature a 3D network of gallium selenite/tellurite with 12-member ring tunnels along b-axis, the distorted MoO(6) octahedra are attached on the wall of the above tunnels. The structure of In(2)Mo(2)Se(2)O(13)(H(2)O) features a new pillared-layered architecture composed of 2D indium(III) selenite layers that are interconnected by Mo(2)O(10) dimers, forming 8-membered ring tunnels along the b-axis. The structure of In(2)MoTe(2)O(10) features a 2D indium oxide layer formed by corner- and edge-sharing InO(6) and InO(7) polyhedra with MoO(4) tetrahedra and TeO(n) (n = 4, 5) polyhedra hanging on both sides of the layer, there are weak interlayer Te-O bonds of 2.512 A. Results of optical diffuse reflectance spectrum measurements indicate that all four compounds are insulators, which are in agreement with results of band structure calculations based on DFT methods.

  20. Evaluation of partnership working in cities in phase IV of the WHO Healthy Cities Network.

    Science.gov (United States)

    Lipp, Alistair; Winters, Tim; de Leeuw, Evelyne

    2013-10-01

    An intersectoral partnership for health improvement is a requirement of the WHO European Healthy Cities Network of municipalities. A review was undertaken in 59 cities based on responses to a structured questionnaire covering phase IV of the network (2003-2008). Cities usually combined formal and informal working partnerships in a pattern seen in previous phases. However, these encompassed more sectors than previously and achieved greater degrees of collaborative planning and implementation. Additional WHO technical support and networking in phase IV significantly enhanced collaboration with the urban planning sector. Critical success factors were high-level political commitment and a well-organized Healthy City office. Partnerships remain a successful component of Healthy City working. The core principles, purpose and intellectual rationale for intersectoral partnerships remain valid and fit for purpose. This applied to long-established phase III cities as well as newcomers to phase IV. The network, and in particular the WHO brand, is well regarded and encourages political and organizational engagement and is a source of support and technical expertise. A key challenge is to apply a more rigorous analytical framework and theory-informed approach to reviewing partnership and collaboration parameters.

  1. Comparative kinetic and equilibrium investigations on the extraction of U(IV) in nitric acid/Tbp or TLA-Kerosene systems

    Energy Technology Data Exchange (ETDEWEB)

    Daoud, J A; Khalifa, S M; Abdel Rahman, N; Aly, H F [Hot laboratories center, Atomic energy authority post code 13758, (Egypt)

    1995-10-01

    The extraction equilibrium of U(IV) by tributyl-phosphate (Tbp) or trilaurylamine (TLA) in kerosene from nitric acid media was investigated. The effect of the different parameters affecting the extraction was separately studied and compared. The kinetics of extraction of U(IV) by Tbp or TLA was also investigated using a stirred lewis cell. The data showed that the rate of extraction of U(IV) by Tbp is controlled by chemical reactions at the interface. In the TLA system, the extraction of U(IV) is controlled by chemical reactions at the interface and bulk phase. Rate equations show that the extraction of U(IV) is first order dependent on Tbp concentration while it is of fractional negative order with respect to TLA. The effect of temperature on the rate of extraction was also studied and the thermodynamic functions were evaluated for the two systems. 5 figs.

  2. Influence of NO2 and metal ions on oxidation of aqueous-phase S(IV in atmospheric concentrations

    Directory of Open Access Journals (Sweden)

    Cláudia R. Martins

    2008-06-01

    Full Text Available An investigation was made of the influence of atmospheric concentrations (15 or 130 ppbv of NO2 on the aqueous-phase oxidation rate of S(IV in the presence and absence of Fe(III, Mn(II and Cr(VI metal ions under controlled experimental conditions (pH, T, concentration of reactants, etc.. The reaction rate in the presence of the NO2 flow was slower than the reaction rate using only clean air with an initial S(IV concentration of 10-4 mol/L. NO2 appears to react with S(IV, producing a kind of inhibitor that slows down the reaction. Conversely, tenfold lower concentrations of S(IV ([S(IV]º = 10-5 mol/L caused a faster reaction in the presence of NO2 than the reaction using purified air. Under these conditions, therefore, the equilibrium shifts to sulfate formation. With the addition of Fe(III, Mn(II or Cr(VI in the presence of a NO2 flow, the reaction occurred faster under all the conditions in which S(IV oxidation was investigated.A reação de oxidação de S(IV em fase aquosa foi estudada em laboratório em presença de NO2 dos íons metálicos Fe(III, Mn(II, e Cr(VI sob condições experimentais controladas (pH, T, concentração dos reagentes, etc.. Na presença de corrente de ar com NO2 (15 ou 130 ppbv a reação de oxidação de S(IV ocorreu mais lentamente do que na presença de ar purificado, para uma concentração inicial de S(IV de 10-4 mol/L. Ao contrário, para concentração inicial de S(IV dez vezes menor ([S(IV]° = 10-5 mol/L a reação ocorreu mais rapidamente na presença de NO2. A explicação está relacionada com o equilíbrio envolvendo a formação de espécies intermediárias de longa vida, que impedem o prosseguimento da reação, porém a depender das concentrações relativas de S(IV e NO2, essas espécies se decompõem deslocando o equilíbrio no sentido de formação de sulfato. A adição dos íons Fe(III, Mn(II ou Cr(VI em presença de corrente de ar com NO2 indicou atividade catalítica para esses íons, em todas

  3. OGLE-IV: Fourth Phase of the Optical Gravitational Lensing Experiment

    Science.gov (United States)

    Udalski, A.; Szymański, M. K.; Szymański, G.

    2015-03-01

    We present both the technical overview and main science drivers of the fourth phase of the Optical Gravitational Lensing Experiment (hereafter OGLE-IV). OGLE-IV is currently one of the largest sky variability surveys worldwide, targeting the densest stellar regions of the sky. The survey covers over 3000 square degrees in the sky and monitors regularly over a billion sources. The main targets include the inner Galactic Bulge and the Magellanic System. Their photometry spans the range of 12System and the Galactic disk. OGLE-IV provides the astronomical community with a number of real time services. The Early Warning System (EWS) contains information on two thousand gravitational microlensing events being discovered in real time annually, the OGLE Transient Detection System (OTDS) delivers over 200 supernovae a year. We also provide the real time photometry of unpredictable variables such as optical counterparts to the X-ray sources and R Coronae Borealis stars. Hundreds of thousands new variable stars have already been discovered and classified by the OGLE survey. The number of new detections will be at least doubled during the current OGLE-IV phase. The survey was designed and optimized primarily to conduct the second generation microlensing survey for exoplanets. It has already contributed significantly to the increase of the discovery rate of microlensing exoplanets and free-floating planets.

  4. Crimson Viper, Phase IV: Field Experimentation Venue Report and CV14 Combined Report

    Science.gov (United States)

    2014-09-01

    battery sources. The system consists of a master node and other nodes used to create a wireless dark network. The wireless mesh nodes are self...create a wireless dark network. The wireless mesh nodes are self-configuring and self-healing. During CV14 Phase IV, separation of nodes averaged...the southern tip of the province, close to the tourism center Pattaya. The Sattahip Naval Base is the largest base of the Royal Thai Navy and is home

  5. Aerodynamic performance analysis of an airborne wind turbine system with NREL Phase IV rotor

    International Nuclear Information System (INIS)

    Saeed, Muhammad; Kim, Man-Hoe

    2017-01-01

    Highlights: • Aerodynamic predictions for a buoyant airborne system at an altitude of 400 m. • Aerodynamic characteristics of NREL Phase IV rotor operating in a shell casing. • Buoyant shell aerodynamics under varying wind conditions. - Abstract: Wind energy becomes more powerful and consistent with an increase in altitude, therefore, harvesting the wind energy at high altitude results in a naturally restocked source of energy which is cheaper and far more efficient than the conventional wind power system. Airborne wind turbine (AWT), one of the many techniques being employed for this purpose, stands out due to its uninterrupted scheme of energy production. This paper presents the aerodynamic performance of AWT system with NREL Phase IV rotor at an altitude of 400 m. Unsteady simulation of the airborne system has been carried out and variations in the rotor’s torque for a complete revolution are reported and discussed. In order to compare the performance of the shell mounted configuration of Phase IV rotor with its standard test configuration, steady state simulations of the rotor are also conducted under various wind conditions for both configurations. Finally, for stable design of the buoyant airborne system, aerodynamic forces on the shell body are computed and reported.

  6. Investigating the reasons of variability in Si IV and C IV broad absorption line troughs of quasars

    Science.gov (United States)

    Stathopoulos, Dimitrios; Lyratzi, Evangelia; Danezis, Emmanuel; Antoniou, Antonios; Tzimeas, Dimitrios

    2017-09-01

    In this paper we analyze the C IV and Si IV broad absorption troughs of two BALQSOs (J101056.69+355833.3, J114548.38+393746.6) to the individual components they consist of. By analyzing a BAL trough to its components we have the advantage to study the variations of the individual absorbing systems in the line of sight and not just the variations of the whole absorption trough or the variations of selected portions of BAL troughs exhibiting changes. We find that the velocity shifts and FWHMs (Full Width at Half Maximum) of the individual components do not vary between an interval of six years. All variable components show changes in the optical depths at line centers which are manifested as variations in the EW (Equivalent Width) of the components. In both BALQSOs, over corresponding velocities, Si IV has higher incidence of variability than C IV. From our analysis, evidence is in favour of different covering fractions between C IV and Si IV. Finally, although most of our results favour the crossing cloud scenario as the cause of variability, there is also strong piece of evidence indicating changing ionization as the source of variability. Thus, a mixed situation where both physical mechanisms contribute to BAL variability is the most possible scenario.

  7. Seismic Safety Margins Research Program (Phase I). Project IV. Structural building response; Structural Building Response Review

    International Nuclear Information System (INIS)

    Healey, J.J.; Wu, S.T.; Murga, M.

    1980-02-01

    As part of the Phase I effort of the Seismic Safety Margins Research Program (SSMRP) being performed by the University of California Lawrence Livermore Laboratory for the US Nuclear Regulatory Commission, the basic objective of Subtask IV.1 (Structural Building Response Review) is to review and summarize current methods and data pertaining to seismic response calculations particularly as they relate to the objectives of the SSMRP. This material forms one component in the development of the overall computational methodology involving state of the art computations including explicit consideration of uncertainty and aimed at ultimately deriving estimates of the probability of radioactive releases due to seismic effects on nuclear power plant facilities

  8. On the determination of Zr(IV), Ce((III), Th(IV) and U(VI) in organic phase using arsenazo-I and arsenazo-III

    International Nuclear Information System (INIS)

    El-Sweify, F.H.; Kamel, M.M.; Shabana, R.

    1997-01-01

    Some organic extractants of different types, namely tridodecylamine (TDA), tricapryl methyl ammonium chloride (TCMA), di(2-ethylhexyl) phosphoric acid (HDEHP) and 1-[thenoyl-(2)]-3,3,3-trifluoroacetone (HTTA) in xylene have been used to study the extraction behaviour of coloured complexes of Zr(IV), Ce(III), Th(IV) and U(VI) from slightly acidic aqueous solutions of arsenazo-III. Spectrophotometric study for the determination of the aforementioned elements, as well as the colouring agents arsenazo-I and arsenazo-III in the organic phase has been carried out. Some factors affecting the spectrophotometric determination of these elements were studied. These factors were hydrogen ion concentration, concentration of the colouring agents in the aqueous phase and diluent type. Absorption spectra and standard curves are given. The molar extinction coefficients have been calculated. 10 figs

  9. X-Band Electron Paramagnetic Resonance Comparison of Mononuclear Mn(IV)-oxo and Mn(IV)-hydroxo Complexes and Quantum Chemical Investigation of Mn(IV) Zero-Field Splitting.

    Science.gov (United States)

    Leto, Domenick F; Massie, Allyssa A; Colmer, Hannah E; Jackson, Timothy A

    2016-04-04

    reproducing experimental E/D values. Overall, this work adds to the limited investigations of Mn(IV) ground-state properties and provides an initial assessment for calculating Mn(IV) ZFS parameters with quantum chemical methods.

  10. Field Sampling Plan for the Operable Units 6-05 and 10-04 Remedial Action, Phase IV

    Energy Technology Data Exchange (ETDEWEB)

    R. Wells

    2006-11-14

    This Field Sampling Plan outlines the collection and analysis of samples in support of Phase IV of the Waste Area Group 10, Operable Units 6-05 and 10-04 remedial action. Phase IV addresses the remedial actions to areas with the potential for unexploded ordnance at the Idaho National Laboratory Site. These areas include portions of the Naval Proving Ground, the Arco High-Altitude Bombing Range, and the Twin Buttes Bombing Range. The remedial action consists of removal and disposal of ordnance by high-order detonation, followed by sampling to determine the extent, if any, of soil that might have been contaminated by the detonation activities associated with the disposal of ordnance during the Phase IV activities and explosives during the Phase II activities.

  11. Crystal and morphological phase transformation of Pb(II) to Pb(IV) in chlorinated water

    International Nuclear Information System (INIS)

    Lytle, Darren A.; White, Colin; Nadagouda, Mallikarjuna N.; Worrall, Adam

    2009-01-01

    Herein, we show an important transformation of Pb(II) to Pb(IV) in chlorinated water under laboratory conditions. The study results will give an insight toward understanding how corrosion by-products on lead materials found in drinking water distribution systems develop and breakdown with time. The experiments were conducted to elucidate the morphology of lead (IV) oxide mineral transformation from hydrocerussite and its relationship to color change over a period of time. Scanning electron microscopy and transmission electron microscopy were used to describe the surface morphology, shape and size of lead solids. X-ray diffraction (XRD) analysis was performed to determine the mineral structure of lead solids. Solids analysis results were compared over a 14-day period of time to define changes in the crystal structure and morphology of lead solids. XRD analysis results of freshly synthesized lead solids showed that hydrocerussite, [Pb 3 (CO 3 ) 2 (OH) 2 ], was the only lead mineral present. After 14 days, a mixture of cerussite (PbCO 3 ) and α-PbO 2 and β-PbO 2 was present. Lead precipitates, i.e. hydrocerussite changed color from white to reddish brown confirming a transformation of the lead phase with time. This was correlated to a change in morphology from flower shaped crystals to hexagonal bars and submicron particles.

  12. Unsteady Aerodynamics Experiment Phases II-IV Test Configurations and Available Data Campaigns

    Energy Technology Data Exchange (ETDEWEB)

    Simms, D. A.; Hand, M. M.; Fingersh, L. J.; Jager, D. W.

    1999-08-19

    The main objective of the Unsteady Aerodynamics Experiment is to provide information needed to quantify the full-scale three-dimensional aerodynamic behavior of horizontal axis wind turbines. To accomplish this, an experimental wind turbine configured to meet specific research objectives was assembled and operated at the National Renewable Energy Laboratory (NREL). The turbine was instrumented to characterize rotating blade aerodynamic performance, machine structural responses, and atmospheric inflow conditions. Comprehensive tests were conducted with the turbine operating in an outdoor field environment under diverse conditions. Resulting data are used to validate aerodynamic and structural dynamics models which are an important part of wind turbine design and engineering codes. Improvements in these models are needed to better characterize aerodynamic response in both the steady-state post-stall and dynamic stall regimes. Much of the effort in the earlier phase of the Unsteady Aerodynamics Experiment focused on developing required data acquisition systems. Complex instrumentation and equipment was needed to meet stringent data requirements while operating under the harsh environmental conditions of a wind turbine rotor. Once the data systems were developed, subsequent phases of experiments were then conducted to collect data for use in answering specific research questions. A description of the experiment configuration used during Phases II-IV of the experiment is contained in this report.

  13. Differential cytotoxicity induced by the Titanium(IV)Salan complex Tc52 in G2-phase independent of DNA damage

    International Nuclear Information System (INIS)

    Pesch, Theresa; Schuhwerk, Harald; Wyrsch, Philippe; Immel, Timo; Dirks, Wilhelm; Bürkle, Alexander; Huhn, Thomas; Beneke, Sascha

    2016-01-01

    Chemotherapy is one of the major treatment modalities for cancer. Metal-based compounds such as derivatives of cisplatin are in the front line of therapy against a subset of cancers, but their use is restricted by severe side-effects and the induction of resistance in treated tumors. Subsequent research focused on development of cytotoxic metal-complexes without cross-resistance to cisplatin and reduced side-effects. This led to the discovery of first-generation titanium(IV)salan complexes, which reached clinical trials but lacked efficacy. New-generation titanium (IV)salan-complexes show promising anti-tumor activity in mice, but their molecular mechanism of cytotoxicity is completely unknown. Four different human cell lines were analyzed in their responses to a toxic (Tc52) and a structurally highly related but non-toxic (Tc53) titanium(IV)salan complex. Viability assays were used to reveal a suitable treatment range, flow-cytometry analysis was performed to monitor the impact of dosage and treatment time on cell-cycle distribution and cell death. Potential DNA strand break induction and crosslinking was investigated by immunostaining of damage markers as well as automated fluorometric analysis of DNA unwinding. Changes in nuclear morphology were analyzed by DAPI staining. Acidic beta-galactosidase activity together with morphological changes was monitored to detect cellular senescence. Western blotting was used to analyze induction of pro-apoptotic markers such as activated caspase7 and cleavage of PARP1, and general stress kinase p38. Here we show that the titanium(IV)salan Tc52 is effective in inducing cell death in the lower micromolar range. Surprisingly, Tc52 does not target DNA contrary to expectations deduced from the reported activity of other titanium complexes. Instead, Tc52 application interferes with progression from G2-phase into mitosis and induces apoptotic cell death in tested tumor cells. Contrarily, human fibroblasts undergo senescence in a

  14. SRP Baseline Hydrogeologic Investigation, Phase 3

    Energy Technology Data Exchange (ETDEWEB)

    Bledsoe, H.W.

    1988-08-01

    The SRP Baseline Hydrogeologic Investigation was implemented for the purpose of updating and improving the knowledge and understanding of the hydrogeologic systems underlying the SRP site. Phase III, which is discussed in this report, includes the drilling of 7 deep coreholes (sites P-24 through P-30) and the installation of 53 observation wells ranging in depth from approximately 50 ft to more than 970 ft below the ground surface. In addition to the collection of geologic cores for lithologic and stratigraphic study, samples were also collected for the determination of physical characteristics of the sediments and for the identification of microorganisms.

  15. Organic derivatives of tin (II/IV): Investigation of their structure

    Energy Technology Data Exchange (ETDEWEB)

    Szirtes, L., E-mail: szirtes@iki.kfki.h [Institute of Isotopes of the Hungarian Academy of Sciences, Budapest H-1525, P.O. Box 77 (Hungary); Megyeri, J., E-mail: megyeri@iki.kfki.h [Institute of Isotopes of the Hungarian Academy of Sciences, Budapest H-1525, P.O. Box 77 (Hungary); Kuzmann, E. [Laboratory of Nuclear Chemistry, CRC of the Hungarian Academy of Science at Eoetvoes University, H-1518 Budapest, P.O. Box 32 (Hungary); Beck, A. [Institute of Isotopes of the Hungarian Academy of Sciences, Budapest H-1525, P.O. Box 77 (Hungary)

    2011-07-15

    The structures of tin(II)-oxalate, tin(IV)Na-EDTA and tin(IV)Na{sub 8}-inositol hexaphosphate were investigated using XRD analysis. Samples were identified using the Moessbauer study, thermal analysis and FTIR spectrometry. The Moessbauer study determined two different oxidation states of tin atoms, and consequently two different tin surroundings in the end products. The tin oxalate was found to be orthorhombic with space group Pnma, a=9.2066(3) A, b=9.7590(1) A, c=13.1848(5) A, V=1184.62 A{sup 3} and Z=8. SnNa-EDTA was found to be monoclinic with space group P2{sub 1}/c{sub 1}, a=10.7544(3) A, b=10.1455(3) A, c=16.5130(6) A, {beta}=98.59(2){sup o}, V=1781.50(4) A{sup 3} and Z=4. Sn(C{sub 6}H{sub 6}Na{sub 8}O{sub 24}P{sub 6}) was found to be amorphous.

  16. Cognitive Biases and Structural Failures in United States Foreign Policy: Explaining Decision-Making Dissonance in Phase IV Policy and Plans for Iraq

    National Research Council Canada - National Science Library

    Hafner, Ferinand

    2007-01-01

    .... This thesis applies four decision-making perspectives the rational actor, organizational process, bureaucratic politics, and individual level approaches to the Phase IV planning process to analyze...

  17. Optimized FFTF Acceptance Test Program covering Phases III, IV, and V

    International Nuclear Information System (INIS)

    Wykoff, W.R.; Jones, D.H.

    1977-03-01

    A detailed review of Phases III, IV, and V of the FFTF Acceptance Test Program has been completed. The purpose of this review was to formulate that test sequence which not only meets requirements for safe, reliable and useful operation of the plant, but also results in the earliest prudent demonstration of full-power performance. A test sequence based on the underlying assumption that sodium flows into the secondary sodium storage tank (T-44) no later than August 31, 1978, is described in detail. A time-scale which allows extra time to put systems and equipment into operation the first time, debugging, and learning how to operate most effectively has been superimposed on the test sequence. Time is not included for major equipment malfunctions. This test plan provides the basis for coordinating the many and varied activities and interfaces necessary for successful and timely execution of the FFTF Acceptance Test Program. In this report, the need dates have been identified for presently scheduled test articles and standard core components

  18. Investigation of neptunium(V) reduction to neptunium(IV) by semiconductor photocatalysis

    International Nuclear Information System (INIS)

    Takahashi, M.; Nakamura, T.; Ikeda, T.; Karasawa, H.

    1990-01-01

    Np(V) is the dominant Np oxidation state in high level liquid waste from reprocessing plants. Since low extractability of Np(V) makes its separation from other nuclei difficult, valence control is required. When a 1mM Np(V) solution of 3M nitric acid was irradiated by a Xe-lamp, using n-SiC (5g/dm 3 ) as photocatalyst and hydrazine (0.1M) as donor, 100% of the Np(V) was reduced to Np(IV) within 30 min at room temperature. Electrochemical investigations suggested that Np(V) is reduced by the atomic hydrogen adsorbed on the photocatalyst surface. According to this mechanism, platinum group metals can act as reducing catalysts for No(V) reduction due to their low hydrogen overvoltage. The proposed mechanism was experimentally confirmed using platinum black (5g/dm 3 ) as catalyst and hydroxylammonium nitrate (0.9M) as reducing agent

  19. Ferrian Ilmenites: Investigating the Magnetic Phase Diagram

    Science.gov (United States)

    Lagroix, F.

    2007-12-01

    The main objective of this study is to investigate the magnetic phase changes within the hematite-ilmenite solid solution, yFeTiO3·(1-y)·Fe2O3. Two sets of synthetic ferrian ilmenites of y-values equal to 0.7, 0.8, 0.9, and 1.0 were available for this study. As currently drawn, the magnetic phase diagram, proposed by Ishikawa et al. [1985, J. Phys. Soc. Jpn. v.54, 312-325], predicts for increasing y values (0.5phase changes for the different compositions investigated. The y=1.0 sample, pure ilmenite, is antiferromagnetic below 57K, the measured Néel temperature. The y=0.9 sample magnetically orders at about 100K in a superparamagnetic state. Hysteresis loops remain effectively closed down to 60K below which an antiferromagnetic order prior to reaching the spin glass state is ambiguous. The y=0.8 sample magnetically orders at about 270K in an initially superparamagnetic states before entering a ferrimagnetic state below about 250K. Lastly, as previously demonstrated in Lagroix et al. [2004, JGR-B, v.109, doi:10.1029/2004JB003076], the y=0.7 samples order ferrimagnetically at 380K. However, like the y=0.7 samples which also demonstrated an antiferromagnetic state at temperature above the Curie temperature, hysteresis loops for y=0.9 and y=0.8 only achieve perfect linearity at 190K and 340K respectively. All samples (except y=1.0) show a frequency dependent amplitude non

  20. Bioelectrical impedance phase angle in clinical practice: implications for prognosis in stage IIIB and IV non-small cell lung cancer

    Directory of Open Access Journals (Sweden)

    Grutsch James F

    2009-01-01

    Full Text Available Abstract Background A frequent manifestation of advanced lung cancer is malnutrition, timely identification and treatment of which can lead to improved patient outcomes. Bioelectrical impedance analysis (BIA is an easy-to-use and non-invasive technique to evaluate changes in body composition and nutritional status. We investigated the prognostic role of BIA-derived phase angle in advanced non-small cell lung cancer (NSCLC. Methods A case series of 165 stages IIIB and IV NSCLC patients treated at our center. The Kaplan Meier method was used to calculate survival. Cox proportional hazard models were constructed to evaluate the prognostic effect of phase angle, independent of stage at diagnosis and prior treatment history. Results 93 were males and 72 females. 61 had stage IIIB disease at diagnosis while 104 had stage IV. The median phase angle was 5.3 degrees (range = 2.9 – 8. Patients with phase angle 5.3 had 12.4 months (95% CI: 10.5 to 18.7; n = 84; (p = 0.02. After adjusting for age, stage at diagnosis and prior treatment history we found that every one degree increase in phase angle was associated with a relative risk of 0.79 (95% CI: 0.64 to 0.97, P = 0.02. Conclusion We found BIA-derived phase angle to be an independent prognostic indicator in patients with stage IIIB and IV NSCLC. Nutritional interventions targeted at improving phase angle could potentially lead to an improved survival in patients with advanced NSCLC.

  1. Catalytic conversion of light alkanes-proof-of-concept stage - Phase IV. Topical report, February 1, 1994--January 31, 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-12-31

    This report details the research performed on Phase IV of the extended Cooperative Agreement. This Phase, entitled C{sub 1}-C{sub 4} Research, provides the research support which accompanies the C{sub 4} Proof-of-Concept Phase (Phase V) as the two major activities of the Cooperative Agreement during calendar 1993. It is the objective of this phase to understand the nature of the catalysts and catalytic activity of perhaloporphyrin complexes uncovered during Phases I-III in order that superior catalytic materials can be made and tested which meet commercial criteria for the oxidation of the C{sub 1}-C{sub 4} light alkane gases found in natural gas and other available hydrocarbon streams. During Phase IV, we have examined the physical and electronic structures of the very active perhaloporphyrin catalysts which we have developed, and have gained an understanding of the properties which make them active. This has led us to design and synthesize materials which are cheaper, more active, more robust and, in general superior for carrying out practical catalysis. Our early generation perhaloporphyrin catalysts, while exhibiting unprecedented catalytic activity, were far too expensive for use in converting natural gas or its C{sub 1}-C{sub 4} components.

  2. Encyclopedia of two-phase heat transfer and flow IV modeling methodologies, boiling of CO₂, and micro-two-phase cooling

    CERN Document Server

    2018-01-01

    Set IV is a new addition to the previous Sets I, II and III. It contains 23 invited chapters from international specialists on the topics of numerical modeling of pulsating heat pipes and of slug flows with evaporation; lattice Boltzmann modeling of pool boiling; fundamentals of boiling in microchannels and microfin tubes, CO2 and nanofluids; testing and modeling of micro-two-phase cooling systems for electronics; and various special topics (flow separation in microfluidics, two-phase sensors, wetting of anisotropic surfaces, ultra-compact heat exchangers, etc.). The invited authors are leading university researchers and well-known engineers from leading corporate research laboratories (ABB, IBM, Nokia Bell Labs). Numerous "must read" chapters are also included here for the two-phase community. Set IV constitutes a "must have" engineering and research reference together with previous Sets I, II and III for thermal engineering researchers and practitioners.

  3. Patientenakzeptanz und Verträglichkeit von Risedronat zur Osteoporosetherapie - Ergebnisse einer Phase IV-Studie

    Directory of Open Access Journals (Sweden)

    Pusch HH

    2001-01-01

    Full Text Available Anwendungsbeobachtungen (Phase IV-Studien haben nach den erfolgreich absolvierten klinischen Prüfungen (Phase III den Zweck, die Verträglichkeit, Sicherheit, Compliance und Akzeptanz eines Präparates in der täglichen praktischen Medizin zu erfassen und auszuwerten. Eine AWB ist prospektiv aufgebaut. Die 1121 in dieser Studie erfaßten Patienten stellen ein solides Fundament für die statistische Aufarbeitung der erhobenen Daten dar. Die Ergebnisse zu den Themen Patientendaten, Diagnosestellung, Risikofaktoren, Frakturen und Mobilität zeigen deutlich, daß hier ein spezielles Patientengut vorliegt: Der Patient mit Osteoporose mit den typischen alterskorrelierten Begleiterkrankungen. Die Osteoporose verläuft, so lange keine Frakturen eintreten, praktisch schmerzfrei - ein Grund, warum diese Erkrankung so oft und so lange ignoriert wird. Begleitende Beschwerden gehen nach der derzeitigen Lehrmeinung stets auf degenerative oder entzündlich-rheumatische Prozesse am Bewegungsapparat zurück. Aus diesem Blickwinkel bieten die Ergebnisse dieser Studie eine Überraschung: Die im Bereich der Wirbelsäule beobachtete und statistisch hochsignifikante Schmerzlinderung. Sie läßt sich jedoch mit der Hemmung des Knochenabbaues durch Risedronat alleine nicht befriedigend erklären. Möglicherweise liegen hier andere, bisher unbekannte pharmakologische Effekte dieser Substanz vor. Zusätzliche Hinweise ergeben sich daraus, daß beim Mb. Paget ähnliche Wirkungen auf die Begleitschmerzen bei Bisphosphonatbehandlung berichtet wurden. Die analgetische Wirkung von Calcitonin ist bekannt, sie beruht auf einer zentralnervösen Wirkung, ebenso wie auf der Hemmung der Freisetzung von freien Kalzium-Ionen, die als Schmerzmediator angesehen werden, aus dem Knochen. Vielleicht liegen hier vergleichbare Effekte vor, die in den Phase II und III Studien nicht zutage treten konnten. Diese überraschenden Ergebnisse sollten Anlaß für weitere Forschungen sein. Die

  4. Developmental assessment of RELAP5/MOD3 code against ROSA-IV/TPTF horizontal two-phase flow experiments

    International Nuclear Information System (INIS)

    Kukita, Yutaka; Asaka, Hideaki; Anoda, Yoshinari; Ishiguro, Misako; Tasaka, Kanji; Mimura, Yuichi; Nemoto, Toshiyuki.

    1990-03-01

    A developmental version of the RELAP5/Mod3 code (as of June 1989) was assessed for accuracy using experimental data taken for high-pressure (7MPa) steam-water two-phase flow in a large-diameter (0.18 m) horizontal-pipe test section of the ROSA-IV Two-Phase Flow Test Facility (TPTF). The agreement between the measured and calculated test section void fractions was much better than that for the previous generation of RELAP5 (MOD2). The improvement was achieved primarily due to the code changes with respect to the flow stratification criterion and interfacial-drag calculation scheme. (author)

  5. Seismic safety margins research program. Phase I final report - Major structure response (Project IV)

    International Nuclear Information System (INIS)

    Benda, B.J.; Johnson, J.J.; Lo, T.Y.

    1981-08-01

    The primary task of the Major Structure Response Project within the Seismic Safety Margins Research Program (SSMRP) was to develop detailed finite element models of the Zion Nuclear Power Plant's containment building and auxiliary-fuel-turbine (AFT) complex. The resulting models served as input to the seismic methodology analysis chain. The containment shell was modeled as a series of beam elements with the shear and bending characteristics of a circular cylindrical shell. Masses and rotary inertias were lumped at nodal points; thirteen modes were included in the analysis. The internal structure was modeled with three-dimensional finite elements, with masses again lumped at selected nodes; sixty modes were included in the analysis. The model of the AFT complex employed thin plate and shell elements to represent the concrete shear walls and floor diaphragms, and beam and truss elements to model the braced frames. Because of the size and complexity of the model, and the potentially large number of degrees of freedom, masses were lumped at a limited number of node points. These points were selected so as to minimize the effect of the discrete mass distribution on structural response. One hundred and thirteen modes were extracted. A second objective of Project IV was to investigate the effects of uncertainty and variability on structural response. To this end, four side studies were conducted. Three of them, briefly summarized in this volume, addressed themselves respectively to an investigation of sources of random variability in the dynamic response of nuclear power plant structures; formulation of a methodology for modeling and evaluating the effects of structural uncertainty on predicted modal characteristics of major nuclear power plant structures and substructures; and a preliminary evaluation of nonlinear responses in shear-wall structures. A fourth side study, reported in detail in this volume, quantified variations in dynamic characteristics and seismic

  6. Kinetic investigation of vanadium (V)/(IV) redox couple on electrochemically oxidized graphite electrodes

    International Nuclear Information System (INIS)

    Wang, Wenjun; Wei, Zengfu; Su, Wei; Fan, Xinzhuang; Liu, Jianguo; Yan, Chuanwei; Zeng, Chaoliu

    2016-01-01

    Highlights: • The VO_2"+/VO"2"+ redox reaction of the electrode could be facilitated to some extent with the increasing anodic corrosion. • A real reaction kinetic equation for the oxidation of VO"2"+ on the electrochemically oxidized electrode has been firstly obtained. • The establishment of the kinetic equation is conducive to predict polarization behaviors of the electrodes in engineering application. - Abstract: The morphology, surface composition, wettability and the kinetic parameters of the electrochemically oxidized graphite electrodes obtained under different anodic polarization conditions have been examined by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), contact angle measurements, steady-state polarization and cyclic voltammetry (CV) tests, with an attempt to investigate the inherent correlation between the physicochemical properties and the kinetic characteristics for carbon electrodes used in an all-vanadium redox flow battery (VRFB). When the anodic polarization potential raises up to 1.8 V vs. SCE, the anodic corrosion of the graphite might happen and a large number of oxygen-containing functional groups generate. The VO_2"+/VO"2"+ redox reaction can be facilitated and the reaction reversibility tends to become better with the increasing anodic potential, possibly owing to the increased surface oxides and the resulting improved wettability of the electrode. Based on this, a real reaction kinetic equation for the oxidation of VO"2"+ has been obtained on the electrode polarized at 1.8 V vs. SCE and it can be also well used to predict the polarization behavior of the oxidized electrode in vanadium (IV) acidic solutions.

  7. Phase II study of ipilimumab in adolescents with unresectable stage III or IV malignant melanoma

    DEFF Research Database (Denmark)

    Geoerger, Birgit; Bergeron, Christophe; Gore, Lia

    2017-01-01

    BACKGROUND: Ipilimumab is approved for the treatment of advanced melanoma in adults; however, little information on the efficacy and safety of ipilimumab in younger patients is available. METHODS: Patients aged 12 to <18 years with previously treated or untreated, unresectable stage III or IV mal...

  8. Lattice distortion and spontaneous {gamma}{sub 5g} ferro-quadrupole moment in phase IV of Ce{sub x}La{sub 1-x}B{sub 6}

    Energy Technology Data Exchange (ETDEWEB)

    Nemoto, Yuichi [Graduate School of Science and Technology, Niigata University, Niigata 950-2181 (Japan)]. E-mail: nemoto@phys.sc.niigata-u.ac.jp; Akatsu, Mitsuhiro [Graduate School of Science and Technology, Niigata University, Niigata 950-2181 (Japan); Goto, Terutaka [Graduate School of Science and Technology, Niigata University, Niigata 950-2181 (Japan); Suzuki, Osamu [National Institute for Materials Science, Tukuba 305-0003 (Japan); Nakamura, Shintaro [Center for Low Temperature Science, Tohoku University, Sendai 980-8577 (Japan); Kunii, Satoru [Department of Physics, Graduate School of Science, Tohoku University, Sendai 980-8578 (Japan)

    2005-04-30

    We have performed low-temperature thermal expansion measurements to investigate lattice effect of the phase IV in Ce{sub x}La{sub 1-x}B{sub 6}, for x=0.75 and 0.70. In phase IV of both compounds, lattice length along the [111] direction shrinks notably, on the other hand length along the [001] direction expands. These results provide evidence that the spontaneous {gamma}{sub 5g} ferro-quadrupole moment ==<>0 is relevant in phase IV because the trigonal lattice distortion is described by the symmetry strain <{epsilon}{sub yz}>=<{epsilon}{sub zx}>=<{epsilon}{sub xy}><>0 simultaneously.

  9. Triclinic-cubic phase transition and negative expansion in the actinide IV (Th, U, Np, Pu) diphosphates

    International Nuclear Information System (INIS)

    Wallez, Gilles; Bregiroux, Damien; Raison, Philippe E.; Bykov, Denis; Konings, Rudy J.M.; Dacheux, Nicolas; Clavier, Nicolas; Delevoye, Laurent; Popa, Karin; Fitch, Andrew N.

    2012-01-01

    The AnP 2 O 7 diphosphates (An = Th, U, Np, Pu) have been synthesized by various routes depending on the stability of the An(IV) cation and its suitability for the unusual octahedral environment. Synchrotron and X-ray diffraction, thermal analysis, Raman spectroscopy, and 31 P nuclear magnetic resonance reveal them as a new family of diphosphates which probably includes the recently studied CeP 2 O 7 . Although they adopt at high temperature the same cubic archetypal cell as the other known MP 2 O 7 diphosphates, they differ by a very faint triclinic distortion at room temperature that results from an ordering of the P 2 O 7 units, as shown using high-resolution synchrotron diffraction for UP 2 O 7 . The uncommon triclinic-cubic phase transition is first order, and its temperature is very sensitive to the ionic radius of An(IV). The conflicting effects which control the thermal variations of the P-O-P angle are responsible for a strong expansion of the cell followed by a contraction at higher temperature. This inversion of expansion occurs at a temperature significantly higher than the phase transition, at variance with the parent compounds with smaller Mn(IV) cations in which the two phenomena coincide. As shown by various approaches, the P-O-b-P linkage remains bent in the cubic form. (authors)

  10. Thermochemical investigation of molten fluoride salts for Generation IV nuclear applications - an equilibrium exercise

    NARCIS (Netherlands)

    van der Meer, J.P.M.

    2006-01-01

    The concept of the Molten Salt Reactor, one of the so-called Generation IV future reactors, is that the fuel, a fissile material, which is dissolved in a molten fluoride salt, circulates through a closed circuit. The heat of fission is transferred to a second molten salt coolant loop, the heat of

  11. X-ray diffraction analysis of the ammonium nitrate IV-III-II and IV-II phase changes under controlled humidity conditions

    International Nuclear Information System (INIS)

    Boeyens, J.C.A.; Ferg, E.; Levendis, D.C.; Schoening, F.R.L.

    1992-01-01

    The first phase transition above room temperature of ammonium nitrate has been investigated as a function of humidity and sample preparation by means of a Weissenberg camera, modified to record the powder diffraction pattern as a function of temperature. Heterogeneous nucleation at the grain surface, inferred from the observed texture that develops in the powder specimens, is related to the effect of humidity during sample preparation on the stability of prills or powders. 19 refs., 4 figs

  12. The phases formed by the dehydration of disodium zirconium (IV) bis(orthophosphate) trihydrate and their ion-exchange behavior

    International Nuclear Information System (INIS)

    Inoue, Yasushi; Yamada, Yoshimune

    1982-01-01

    The phase transformation of Na 2 Zr(PO 4 ) 2 .3H 2 O which had been obtained from zirconium (IV) bis(hydrogenphosphate) monohydrate(α-zirconium phosphate), prepared by the direct precipitation method, was studied by means of gravimetry, X-ray analysis, and acid-base titration. When the material was heated for 2d, it was transformed to a monohydrate at 80 0 C and then successively to three anhydrous phases, depending on the temperature. The monohydrate was also formed by letting the trihydrate stand over P 2 O 5 at room temperature for longer than two weeks. The processes were confirmed to be irreversible by an examination of the rehydration behavior, from which the conditions of the storage of five modifications of disodium zirconium (IV) bis(orthophosphate) were established. It is of special interest that the second anhydrous phase reverted to the first one when it was allowed to stand at room temperature in air or in a desiccator. The rate of the reversion decreased with the temperature of heat-treatment and with a decrease in the relative humidity of the surroundings. The difference between the present results and Clearfield's was clarified and attributed mainly to the difference in the crystallinity of the starting α-zirconium phosphate. (author)

  13. Remedial Design/Remedial Action Work Plan for Operable Units 6-05 and 10-04, Phase IV

    Energy Technology Data Exchange (ETDEWEB)

    R. P. Wells

    2006-11-14

    This Phase IV Remedial Design/Remedial Action Work Plan addresses the remediation of areas with the potential for UXO at the Idaho National Laboratory. These areas include portions of the Naval Proving Ground, the Arco High-Altitude Bombing Range, and the Twin Buttes Bombing Range. Five areas within the Naval Proving Ground that are known to contain UXO include the Naval Ordnance Disposal Area, the Mass Detonation Area, the Experimental Field Station, The Rail Car Explosion Area, and the Land Mine Fuze Burn Area. The Phase IV remedial action will be concentrated in these five areas. For other areas, such as the Arco High-Altitude Bombing Range and the Twin Buttes Bombing Range, ordnance has largely consisted of sand-filled practice bombs that do not pose an explosion risk. Ordnance encountered in these areas will be addressed under the Phase I Operations and Maintenance Plan that allows for the recovery and disposal of ordnance that poses an imminent risk to human health or the environment.

  14. Theoretical analysis of nuclear reactors (Phase II), I-V, Part IV, Depletion of nuclear fuel; Razrada metoda teorijske analize nuklearnih reaktora (II faza) I-V, IV Deo, Promena izotopnog sastava goriva

    Energy Technology Data Exchange (ETDEWEB)

    Pop-Jordanov, J [Institute of Nuclear Sciences Boris Kidric, Vinca, Beograd (Serbia and Montenegro)

    1962-10-15

    This phase of the project deals with the U{sup 238} isotope chain with the analysis of Pu{sup 239} build-up. Part one of the report shows two theoretical approaches, one leading to a system of differential equations which could be solved by using a computer, and the second Machinari-Goto method which gives analytical expressions for approximations for certain isotopes. Part two includes the results obtained by using digital computer ZUSE-Z22-R.

  15. On some derived compounds of fluorides of Cerium III or IV: defined compounds and non stoichiometric phases

    International Nuclear Information System (INIS)

    Besse, Jean-Pierre

    1968-01-01

    This research study addresses the study of rare earth fluorides. It reports the preparation and study of new fluoro-cerates (IV) in order to complete the set of already known compounds (ammonium fluoro-cerate, and alkaline earth compounds), the study of binary CeF 3 binary systems, monovalent and divalent fluorides, and CeF 3 -NF 2 -N'F ternary systems, and the study of non stoichiometric phases in CeF 3 oxides, sulphides and selenides [fr

  16. Japanese contributions to IAEA INTOR workshop, phase two A, part 2, chapter IV: RF heating and current drive

    International Nuclear Information System (INIS)

    Sugihara, Masayoshi; Kimura, Haruyuki; Okazaki, Takashi

    1985-07-01

    This report corresponds to Chapter IV of Japanese contribution report to IAEA INTOR Workshop, phase Two A, Part 2. Data base assessments of plasma heating and launcher system design for Ion Cyclotron Range of Frequency (ICRF) wave, for Lower Hybrid Range of Frequency (LHRF) wave, and for Electron Cyclotron Range of Frequency (ECRF) wave are made. Assessments of current drive by LHRF, and of start-up assist and profile control by ECRF are also made. R and D programmes both physics and technology for each of the waves are specified. Applications of these waves to INTOR are examined. (author)

  17. Lattice investigations of the QCD phase diagram

    International Nuclear Information System (INIS)

    Guenther, Jana

    2016-01-01

    To understand the physics in the early universe as well as in heavy ion collisions a throughout understanding of the theory of strong interaction, quantum chromodynamics (QCD), is important. Lattice QCD provides a tool to study it from first principles. However due to the sign problem direct simulations with physical conditions are at the moment limited to zero chemical potential. In this thesis I present a circumvention of this problem. We can gain information on the QCD phase diagram and the equation of state from analytical continuation of results extracted from simulations at imaginary chemical potential. The topological susceptibility is very expensive to compute in Lattice QCD. However it provides an important ingredient for the estimation of the axion mass. The axion is a possible candidate for a dark matter, which plays in important role in the understanding of our universe. In this thesis I discuss two techniques that make it possible to determine the topological susceptibility and allow for an estimation of the axion mass. I then use this mass restrain to analyze the idea of an experiment to detect axions with a dielectric mirror.

  18. Lattice investigations of the QCD phase diagram

    Energy Technology Data Exchange (ETDEWEB)

    Guenther, Jana

    2016-12-15

    To understand the physics in the early universe as well as in heavy ion collisions a throughout understanding of the theory of strong interaction, quantum chromodynamics (QCD), is important. Lattice QCD provides a tool to study it from first principles. However due to the sign problem direct simulations with physical conditions are at the moment limited to zero chemical potential. In this thesis I present a circumvention of this problem. We can gain information on the QCD phase diagram and the equation of state from analytical continuation of results extracted from simulations at imaginary chemical potential. The topological susceptibility is very expensive to compute in Lattice QCD. However it provides an important ingredient for the estimation of the axion mass. The axion is a possible candidate for a dark matter, which plays in important role in the understanding of our universe. In this thesis I discuss two techniques that make it possible to determine the topological susceptibility and allow for an estimation of the axion mass. I then use this mass restrain to analyze the idea of an experiment to detect axions with a dielectric mirror.

  19. Phase II trial of the regulatory T cell-depleting agent, denileukin diftitox, in patients with unresectable stage IV melanoma

    International Nuclear Information System (INIS)

    Telang, Sucheta; Gragg, Hana; Clem, Brian F; McMasters, Kelly M; Miller, Donald M; Chesney, Jason; Rasku, Mary Ann; Clem, Amy L; Carter, Karen; Klarer, Alden C; Badger, Wesley R; Milam, Rebecca A; Rai, Shesh N; Pan, Jianmin

    2011-01-01

    We previously found that administration of an interleukin 2/diphtheria toxin conjugate (DAB/IL2; Denileukin Diftitox; ONTAK) to stage IV melanoma patients depleted CD4 + CD25 HI Foxp3 + regulatory T cells and expanded melanoma-specific CD8 + T cells. The goal of this study was to assess the clinical efficacy of DAB/IL2 in an expanded cohort of stage IV melanoma patients. In a single-center, phase II trial, DAB/IL2 (12 μg/kg; 4 daily doses; 21 day cycles) was administered to 60 unresectable stage IV melanoma patients and response rates were assessed using a combination of 2-[ 18 F]-fluoro-2-deoxy-glucose (FDG)-positron emission tomography (PET) and computed tomography (CT) imaging. After DAB/IL2 administration, 16.7% of the 60 patients had partial responses, 5% stable disease and 15% mixed responses. Importantly, 45.5% of the chemo/immuno-naïve sub-population (11/60 patients) experienced partial responses. One year survival was markedly higher in partial responders (80 ± 11.9%) relative to patients with progressive disease (23.7 ± 6.5%; p value < 0.001) and 40 ± 6.2% of the total DAB/IL2-treated population were alive at 1 year. These data support the development of multi-center, randomized trials of DAB/IL2 as a monotherapy and in combination with other immunotherapeutic agents for the treatment of stage IV melanoma. http://www.clinicaltrials.gov/ct2/show/NCT00299689

  20. An investigation of group IV alloys and their applications in bipolar transistors

    International Nuclear Information System (INIS)

    Anteney, I.M.

    2000-09-01

    This thesis investigates the use of carbon in group IV alloys and their potential uses in bipolar transistors. The first part of the thesis investigates the ability of carbon to suppress transient enhanced diffusion in SiGe heterojunction bipolar transistors, whilst the second part deals with the impact of carbon incorporation on the electrical properties of polycrystalline silicon and silicon-germanium films. A background doping concentration (10 20 cm -3 ) of C has been introduced into the base of SiGe HBTs with the aim of studying the effects of C on TED of B from the base. An electrical method is used to extract the bandgap narrowing in the base of SiGe and SiGe:C HBTs through measurements of the temperature dependence of I c at different C/B reverse biases. The method is very sensitive to small amounts of dopant out-diffusion from the base and hence is ideal for determining the effect of C on TED. Extracted BGN values of 115meV and 173meV were obtained for the SiGe and SiGe:C HBTs respectively, for a C/B reverse bias of 0V. Increasing the C/B reverse bias to 1V increased the extracted BGN of the SiGe HBT to 145meV, but left the SiGe:C value unchanged. This demonstrates that no parasitic energy barrier exists in the SiGe:C HBT and that TED has been suppressed. The effect of carbon position and concentration has been studied by introducing a peak C concentration of 10 20 cm -3 in the collector and 1.1x10 19 cm -3 or 1.5x10 19 cm -3 C in the base. From these measurements it has been shown that TED is only suppressed in the device with 1.5x10 19 cm -3 C in the base, indicating that a C concentration of 1.5x10 19 cm -3 is needed to suppress TED and that the C needs to be co-located with the B profile. The effects of carbon on the electrical properties of polycrystalline Si and SiGe films have been investigated. The resistivity, Hall mobility (μ H ) and effective carrier concentration (N EFF ) of n- and p-type polySi 1-y C y and polySi 0.82-y Ge 0.18 C y layers

  1. Thermal decomposition and spectroscopic investigation of a new aqueous glycolato(-peroxo) Ti(IV) solution-gel precursor

    International Nuclear Information System (INIS)

    De Dobbelaere, Christopher; Mullens, Jules; Hardy, An; Van Bael, Marlies K.

    2011-01-01

    Highlights: → A totally water based glycolato-Ti(IV) precursor is presented and characterized. → The precursors' thermal decomposition profile depends on the ligand to metal ratio. → Titanium is coordinated in an unidentate fashion by the glycolate anion. → Smooth and uniform TiO 2 films can be prepared from the precursor solution. - Abstract: A new aqueous solution-gel precursor based on water soluble glycolato(-peroxo)-Ti(IV) complexes is developed for the preparation of TiO 2 films. With regard to the decomposition of complexes towards oxide formation, it is important to gain insight in the chemical transformations inside the precursor during thermal treatment. Therefore, the thermo-oxidative decomposition pathway of a gel obtained by slow evaporation of the precursor solution is described based on hyphenated thermogravimetric analysis with Fourier transform infrared spectroscopy (TGA-FTIR) and mass spectrometry (TGA-MS). Pure glycolic acid is used as a reference system for this study. By varying the molar glycolic acid to Ti(IV) ratio, the thermal decomposition of the gel can be drastically shortened and the profile's course changed. Gel structure and chemical changes in the gel upon heating are also studied by means of off-line FTIR. A unidentate coordination of the titanium(IV) ion by the carboxylate group of the glycolato ligands and the involvement of the hydroxyl group is confirmed. Phase formation at certain points in the thermal decomposition is studied by X-ray diffraction and Raman spectroscopy. Finally, it is proven that the new precursor is a valuable candidate for the deposition of low carbon containing solution-gel films which can ultimately be converted into smooth and uniform TiO 2 films.

  2. Thermal decomposition and spectroscopic investigation of a new aqueous glycolato(-peroxo) Ti(IV) solution-gel precursor

    Energy Technology Data Exchange (ETDEWEB)

    De Dobbelaere, Christopher, E-mail: christopher.dedobbelaere@uhasselt.be [Hasselt University, Institute for Materials Research, Inorganic and Physical Chemistry, Agoralaan Building D, B-3590 Diepenbeek (Belgium); Mullens, Jules, E-mail: jules.mullens@uhasselt.be [Hasselt University, Institute for Materials Research, Inorganic and Physical Chemistry, Agoralaan Building D, B-3590 Diepenbeek (Belgium); Hardy, An, E-mail: an.hardy@uhasselt.be [Hasselt University, Institute for Materials Research, Inorganic and Physical Chemistry, Agoralaan Building D, B-3590 Diepenbeek (Belgium); IMEC vzw, Division IMOMEC, Agoralaan Building D, B-3590 Diepenbeek (Belgium); Van Bael, Marlies K., E-mail: marlies.vanbael@uhasselt.be [Hasselt University, Institute for Materials Research, Inorganic and Physical Chemistry, Agoralaan Building D, B-3590 Diepenbeek (Belgium); IMEC vzw, Division IMOMEC, Agoralaan Building D, B-3590 Diepenbeek (Belgium)

    2011-06-10

    Highlights: {yields} A totally water based glycolato-Ti(IV) precursor is presented and characterized. {yields} The precursors' thermal decomposition profile depends on the ligand to metal ratio. {yields} Titanium is coordinated in an unidentate fashion by the glycolate anion. {yields} Smooth and uniform TiO{sub 2} films can be prepared from the precursor solution. - Abstract: A new aqueous solution-gel precursor based on water soluble glycolato(-peroxo)-Ti(IV) complexes is developed for the preparation of TiO{sub 2} films. With regard to the decomposition of complexes towards oxide formation, it is important to gain insight in the chemical transformations inside the precursor during thermal treatment. Therefore, the thermo-oxidative decomposition pathway of a gel obtained by slow evaporation of the precursor solution is described based on hyphenated thermogravimetric analysis with Fourier transform infrared spectroscopy (TGA-FTIR) and mass spectrometry (TGA-MS). Pure glycolic acid is used as a reference system for this study. By varying the molar glycolic acid to Ti(IV) ratio, the thermal decomposition of the gel can be drastically shortened and the profile's course changed. Gel structure and chemical changes in the gel upon heating are also studied by means of off-line FTIR. A unidentate coordination of the titanium(IV) ion by the carboxylate group of the glycolato ligands and the involvement of the hydroxyl group is confirmed. Phase formation at certain points in the thermal decomposition is studied by X-ray diffraction and Raman spectroscopy. Finally, it is proven that the new precursor is a valuable candidate for the deposition of low carbon containing solution-gel films which can ultimately be converted into smooth and uniform TiO{sub 2} films.

  3. Addendum to the Phase 2 Sampling and Analysis Plan for the Clinch River Remedial Investigation

    International Nuclear Information System (INIS)

    1994-03-01

    This document is an addendum to the Phase 2 Sampling and Analysis Plan for the Clinch River Remedial Investigation (DOE 1993). The Department of Energy--Oak Ridge Operations (DOE-ORO) is proposing this addendum to the US Envianmental Protection Agency, Region IV (EPA-IV), and the Tennessee Department of Environment and Conservation (TDEC) as a reduced sampling program on the Clinch River arm of Watts Bar Reservoir and on Poplar Creek. DOE-ORO is proposing to maximize the use of existing data and minimize the collection of new data for water, sediment, and biota during Phase 2 of the Clinch River Remedial Investigation. The existing data along with the additional data collected in Phase 2 would be used to perform a baseline risk assessment and make remedial decisions. DOE-ORO considers that the existing data, the additional data collected in Phase 2, and on-site remedial investigation data would be sufficient to understand the nature and extent of the contamination problem in the Clinch River, perform a baseline risk assessment,and make remedial decisions. This addendum is organized in three sections. The first section provides background information and describes a rationale for modifying the Phase 2 Sampling and Analysis Plan. Section 2 presents a summary of the existing data for the Clinch River arm of Watts Bar Reservoir and an evaluation of the sufficiency of this data for a baseline human health and ecological risk assessment. Section 3 describes the revised Phase 2 Sampling and Analysis Plan for surface water, sediment, and biota in the Clinch River OU and in the Poplar Creek OU

  4. Kilowatt isotope power system, Phase II Plan. Volume IV. Teledyne FSCD vs GDS

    Energy Technology Data Exchange (ETDEWEB)

    1978-03-15

    This Volume contains Teledyne's input to the Kilowatt Isotope Power System Phase II Plan. Included is a description of the Flight System Heat Generation System, Flight System Radiator, Thermal Insulation Stability, GDS Heat Generation System and GDS Radiator.

  5. Development of methods for measuring materials nuclear characteristics, Phases, I, II, II and IV

    International Nuclear Information System (INIS)

    Maglic, R.

    1963-04-01

    This report contains the following phases of the project 'measurement of nuclear characteristics of reactor materials': nuclear performances of the neutron chopper; method for measuring total effective cross sections by transmission method on the chopper; review of methods for measuring activation cross sections; measurement of neutron spectra of the RA reactor and measurement of total effective cross section of gold by using the chopper

  6. Microscopy investigation on the corrosion of Canadian generation IV SCWR materials

    Energy Technology Data Exchange (ETDEWEB)

    Li, J. [CanmetMATERIALS, Hamilton, ON (Canada); Huang, X. [Carleton Univ., Ottawa, ON (Canada); Zeng, Y.; Zheng, W. [CanmetMATERIALS, Hamilton, ON (Canada); Woo, O.T.; Guzonas, D. [Atomic Energy Canada Limited, Chalk River, ON (Canada)

    2014-07-01

    Selection of fuel cladding materials for the Canadian Generation-IV Supercritical Water-cooled Reactor (SCWR) concept faces major challenges due to the severe operating conditions (650 {sup o}C and 25 MPa). High temperature microstructure stability and excellent resistance to general corrosion and stress corrosion cracking are key criteria. While corrosion resistance are generally assessed using weight change measurements and surface oxide examinations by optical and Scanning Electron Microscope (SEM) techniques, for materials exposed to SCW conditions, advanced analytical techniques that involve the use of Focused Ion Beam (FIB) and Transmission Electron Microscopy (TEM) techniques are required. This paper provides examples of such work conducted at CanmetMATERIALS and AECL to provide an in-depth understanding of the corrosion mechanisms of alloys exposed under SCW conditions. (author)

  7. Input Calibration and Validation of RELAP5 Against CIRCUS-IV Single Channel Tests on Natural Circulation Two-Phase Flow Instability

    Directory of Open Access Journals (Sweden)

    Viet-Anh Phung

    2015-01-01

    Full Text Available RELAP5 is a system thermal-hydraulic code that is used to perform safety analysis on nuclear reactors. Since the code is based on steady state, two-phase flow regime maps, there is a concern that RELAP5 may provide significant errors for rapid transient conditions. In this work, the capability of RELAP5 code to predict the oscillatory behavior of a natural circulation driven, two-phase flow at low pressure is investigated. The simulations are compared with a series of experiments that were performed in the CIRCUS-IV facility at the Delft University of Technology. For this purpose, we developed a procedure for calibration of the input and code validation. The procedure employs (i multiple parameters measured in different regimes, (ii independent consideration of the subsections of the loop, and (iii assessment of importance of the uncertain input parameters. We found that predicted system parameters are less sensitive to variations of the uncertain input and boundary conditions in high frequency oscillations regime. It is shown that calculation results overlap experimental values, except for the high frequency oscillations regime where the maximum inlet flow rate was overestimated. This finding agrees with the idea that steady state, two-phase flow regime maps might be one of the possible reasons for the discrepancy in case of rapid transients in two-phase systems.

  8. Controlled in meso phase crystallization--a method for the structural investigation of membrane proteins.

    Directory of Open Access Journals (Sweden)

    Jan Kubicek

    Full Text Available We investigated in meso crystallization of membrane proteins to develop a fast screening technology which combines features of the well established classical vapor diffusion experiment with the batch meso phase crystallization, but without premixing of protein and monoolein. It inherits the advantages of both methods, namely (i the stabilization of membrane proteins in the meso phase, (ii the control of hydration level and additive concentration by vapor diffusion. The new technology (iii significantly simplifies in meso crystallization experiments and allows the use of standard liquid handling robots suitable for 96 well formats. CIMP crystallization furthermore allows (iv direct monitoring of phase transformation and crystallization events. Bacteriorhodopsin (BR crystals of high quality and diffraction up to 1.3 Å resolution have been obtained in this approach. CIMP and the developed consumables and protocols have been successfully applied to obtain crystals of sensory rhodopsin II (SRII from Halobacterium salinarum for the first time.

  9. Waste area Grouping 2 Phase I remedial investigation: Sediment and Cesium-137 transport modeling report

    International Nuclear Information System (INIS)

    Clapp, R.B.; Bao, Y.S.; Moore, T.D.; Brenkert, A.L.; Purucker, S.T.; Reece, D.K.; Burgoa, B.B.

    1996-06-01

    This report is one of five reports issued in 1996 that provide follow-up information to the Phase I Remedial Investigation (RI) Report for Waste Area Grouping (WAG) 2 at Oak Ridge National Laboratory (ORNL). The five reports address areas of concern that may present immediate risk to public health at the Clinch River and ecological risk within WAG 2 at ORNL. A sixth report, on groundwater, in the series documenting WAG 2 RI Phase I results were part of project activities conducted in FY 1996. The five reports that complete activities conducted as part of Phase I of the Remedial Investigation (RI) for WAG 2 are as follows: (1) Waste Area Grouping 2, Phase I Task Data Report: Seep Data Assessment, (2) Waste Area Grouping 2, Phase I Task Data Report: Tributaries Data Assessment, (3) Waste Area Grouping 2, Phase I Task Data Report: Ecological Risk Assessment, (4) Waste Area Grouping 2, Phase I Task Data Report: Human Health Risk Assessment, (5) Waste Area Grouping 2, Phase I Task Data Report: Sediment and 137 Cs Transport Modeling In December 1990, the Remedial Investigation Plan for Waste Area Grouping 2 at Oak Ridge National Laboratory was issued (ORNL 1990). The WAG 2 RI Plan was structured with a short-term component to be conducted while upgradient WAGs are investigated and remediated, and a long-term component that will complete the RI process for WAG 2 following remediation of upgradient WAGs. RI activities for the short-term component were initiated with the approval of the Environmental Protection Agency, Region IV (EPA), and the Tennessee Department of Environment and Conservation (TDEC). This report presents the results of an investigation of the risk associated with possible future releases of 137 Cs due to an extreme flood. The results are based on field measurements made during storms and computer model simulations

  10. Reversed phase chromatographic behaviour of Pu (III), Pu (IV) and Pu (VI) in presence of α-hydroxyisobutyric acid

    International Nuclear Information System (INIS)

    Jaison, P.G.; Telmore, V.M.; Kumar, Pranaw

    2016-01-01

    Understanding the aqueous chemistry of plutonium is important in process conditions as well as in environmental conditions. Since plutonium possesses multiple oxidation states which can coexist in solution, a reliable method for the identification of these oxidation states is essential to understand its physical and chemical processes. The identification of plutonium oxidation states is conventionally determined through a series of liquid-liquid extraction procedures using selective extractants. Spectroscopic and laser based techniques also have been used for the identification of its oxidation state in solutions. Liquid chromatographic behavior of different oxidation states of Pu and other actinide ions is reported to correlate their retention behaviour with stability constants. Objective of the present work is to study the reversed phase chromatography behavior of the three oxidation states of plutonium viz. Pu(III), Pu(IV) and Pu(VI) in presence of á-hydroxyisobutyric acid (HIBA) as an eluent

  11. Increasing the deposition rate of microcrystalline and amorphous silicon thin films for photovoltaic applications - Phase IV: 1997-1999

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-07-01

    This report on behalf of the Swiss Federal Office of Energy (SFOE) describes Phase IV of the project to test the feasibility and usefulness of Very High Frequency (VHF) plasma operation in large-area reactors suitable for the production of solar cell panels using thinly-deposited micro-crystalline silicon films. The report discusses the results of fast-deposition tests and trials using high-current DC arcs and VHF techniques to obtain deposition rates and film quality suitable for industrial processes for the production of thin-film solar cell panels. The effects of alternative plasma chemistry were also studied by adding silicon tetrafluoride to the standard silane/hydrogen mixtures. The report is concluded with calculations for optimum radio-frequency (RF) contact configuration for large area reactors with 1 m{sup 2} electrodes.

  12. A tetrapositive metal ion in the gas phase: Thorium(IV) coordinated by neutral tridentate ligands

    International Nuclear Information System (INIS)

    Gong, Yu; Tian, Guoxin; Rao, Linfeng; Gibson, John K.; Hu, Han-Shi; Li, Jun

    2013-01-01

    Sheltering thorium ions: A Th 4+ ion supported by three neutral tetramethyl-3-oxaglutaramide ligands (L=TMOGA) is produced in the gas phase by electrospray ionization. The thorium in chiral Th(L) 3 4+ is coordinated by nine oxygen atoms. Quantum chemical studies revealed a decrease in Th-O binding energies and bond orders and an increase in bond lengths, as the number of coordinating ligands increases. (Copyright copyright 2013 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  13. A tetrapositive metal ion in the gas phase: Thorium(IV) coordinated by neutral tridentate ligands

    Energy Technology Data Exchange (ETDEWEB)

    Gong, Yu; Tian, Guoxin; Rao, Linfeng; Gibson, John K. [Chemical Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, CA (United States); Hu, Han-Shi [Department of Chemistry and Laboratory of Organic Optoelectronics and Molecular Engineering of the Ministry of Education, Tsinghua University (China); Li, Jun [Department of Chemistry and Laboratory of Organic Optoelectronics and Molecular Engineering of the Ministry of Education, Tsinghua University (China); William R. Wiley Environmental Molecular Sciences Laboratory, Pacific Northwest National Laboratory (United States)

    2013-07-01

    Sheltering thorium ions: A Th{sup 4+} ion supported by three neutral tetramethyl-3-oxaglutaramide ligands (L=TMOGA) is produced in the gas phase by electrospray ionization. The thorium in chiral Th(L){sub 3}{sup 4+} is coordinated by nine oxygen atoms. Quantum chemical studies revealed a decrease in Th-O binding energies and bond orders and an increase in bond lengths, as the number of coordinating ligands increases. (Copyright copyright 2013 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  14. Study on phase stability and ionic conductivity in HfIV-substituted bismuth vanadate

    International Nuclear Information System (INIS)

    Beg, Saba; Al-Areqi, Niyazi A.S.

    2009-01-01

    Influence of dopant concentration on thermal behaviour of Bi 4 Hf x V 2-x O 11-(x/2)-δ was studied over composition range 0 ≤ x ≤ 0.40 by combination of data obtained from X-ray powder diffraction, differential scanning calorimetric and conductivity measurements. For very low dopant concentrations, the system was found to mimic the parent compound in exhibiting two consecutive transitions,α ↔ β ↔ γ, with slightly different onset temperatures compared to that of parent, whereas the existence of β ↔ γ transition was well confirmed in composition range 0.15 ≤ x ≤ 0.20 and typified in Arrhenius plots to two line regions of different activation energy. For composition range 0.25 ≤ x ≤ 0.40, no significant structural changes associated with γ' ↔ γ transition is visible in X-ray powder diffraction data with variable temperature. Despite this, the existence of γ' ↔ γ transition was evident by some complex incommensurate modulations observed in Arrhenius plots and DSC/DTA thermograms. It was surprising to note the appearance of a new destructive γ ↔ β' transition, resulting from distortion of the tetragonal phase structure at higher temperatures. The relationship between phase stability and ionic conductivity was also rationalized.

  15. Standards for Clinical Trials in Male and Female Sexual Dysfunction: I. Phase I to Phase IV Clinical Trial Design.

    Science.gov (United States)

    Fisher, William A; Gruenwald, Ilan; Jannini, Emmanuele A; Lev-Sagie, Ahinoam; Lowenstein, Lior; Pyke, Robert E; Reisman, Yakov; Revicki, Dennis A; Rubio-Aurioles, Eusebio

    2016-12-01

    This series of articles outlines standards for clinical trials of treatments for male and female sexual dysfunctions, with a focus on research design and patient-reported outcome assessment. These articles consist of revision, updating, and integration of articles on standards for clinical trials in male and female sexual dysfunction from the 2010 International Consultation on Sexual Medicine developed by the authors as part of the 2015 International Consultation on Sexual Medicine. We are guided in this effort by several principles. In contrast to previous versions of these guidelines, we merge discussion of standards for clinical trials in male and female sexual dysfunction in an integrated approach that emphasizes the common foundational practices that underlie clinical trials in the two settings. We present a common expected standard for clinical trial design in male and female sexual dysfunction, a common rationale for the design of phase I to IV clinical trials, and common considerations for selection of study population and study duration in male and female sexual dysfunction. We present a focused discussion of fundamental principles in patient- (and partner-) reported outcome assessment and complete this series of articles with specific discussions of selected aspects of clinical trials that are unique to male and to female sexual dysfunction. Our consideration of standards for clinical trials in male and female sexual dysfunction attempts to embody sensitivity to existing and new regulatory guidance and to address implications of the evolution of the diagnosis of sexual dysfunction that have been brought forward in the Diagnostic and Statistical Manual of Mental Disorders, Fifth Edition. The first article in this series focuses on phase I to phase IV clinical trial design considerations. Subsequent articles in this series focus on the measurement of patient-reported outcomes, unique aspects of clinical trial design for men, and unique aspects of clinical

  16. The stressor criterion in DSM-IV posttraumatic stress disorder: an empirical investigation.

    Science.gov (United States)

    Breslau, N; Kessler, R C

    2001-11-01

    The DSM-IV two-part definition of posttraumatic stress disorder (PTSD) widened the variety of stressors (A1) and added a subjective component (A2). The effects of the revised stressor criterion on estimates of exposure and PTSD in a community sample are evaluated. A representative sample of 2181 persons in southeast Michigan were interviewed about lifetime history of traumatic events and PTSD. The evaluation of the revised two-part definition is based on a randomly selected sample of events that represents the total pool of traumatic events experienced in the community. The enlarged definition of stressors in A1 increased the total number of events that can be used to diagnose PTSD by 59%. The majority of A1 events (76.6%) involved the emotional response in A2. Females were more likely than males to endorse A2 (adjusted odds ratio = 2.66; 95% confidence interval 1.92, 3.71). Of all PTSD cases resulting from the representative sample of events, 38% were attributable to the expansion of qualifying events in A1. The identification of exposures that lead to PTSD were not improved materially by A2 however, events that did not involve A2 rarely resulted in PTSD. Compared to previous definitions, the wider variety of stressors in A1 markedly increased the number of events experienced in the community that can be used to diagnose PTSD. Furthermore, A2 might be useful as a separate criterion, an acute response necessary for the emergence of PTSD, and might serve as an early screen for identifying a subset of recently exposed persons at virtually no risk for PTSD. The utility of A2 as a screen must be tested prospectively.

  17. 2D phase tomography of biotissues: IV. Wavelet processing of phase tomograms of the background and precancerous endometrial states

    Science.gov (United States)

    Peresunko, A. P.; Zavadovskya, I. G.

    2004-06-01

    The paper deals with the studying of prognostic possibilities of determining the orientation structure of endometrial strome in the normal state and hiperplasia. The laser diagnostic of endometrial state is based on the principles of optical changes of laser radiation during its passing through the histological sample with the following investigation of its wavelet coefficients.

  18. ESR imaging investigations of two-phase systems.

    Science.gov (United States)

    Herrmann, Werner; Stösser, Reinhard; Borchert, Hans-Hubert

    2007-06-01

    The possibilities of electron spin resonance (ESR) and electron spin resonance imaging (ESRI) for investigating the properties of the spin probes TEMPO and TEMPOL in two-phase systems have been examined in the systems water/n-octanol, Miglyol/Miglyol, and Precirol/Miglyol. Phases and regions of the phase boundary could be mapped successfully by means of the isotropic hyperfine coupling constants, and, moreover, the quantification of rotational and lateral diffusion of the spin probes was possible. For the quantitative treatment of the micropolarity, a simplified empirical model was established on the basis of the Nernst distribution and the experimentally determined isotropic hyperfine coupling constants. The model does not only describe the summarized micropolarities of coexisting phases, but also the region of the phase boundary, where solvent molecules of different polarities and tendencies to form hydrogen bonds compete to interact with the NO group of the spin probe. Copyright 2007 John Wiley & Sons, Ltd.

  19. Numerical Predictions of Wind Turbine Power and Aerodynamic Loads for the NREL Phase II and IV Combined Experiment Rotor

    Science.gov (United States)

    Duque, Earl P. N.; Johnson, Wayne; vanDam, C. P.; Chao, David D.; Cortes, Regina; Yee, Karen

    1999-01-01

    Accurate, reliable and robust numerical predictions of wind turbine rotor power remain a challenge to the wind energy industry. The literature reports various methods that compare predictions to experiments. The methods vary from Blade Element Momentum Theory (BEM), Vortex Lattice (VL), to variants of Reynolds-averaged Navier-Stokes (RaNS). The BEM and VL methods consistently show discrepancies in predicting rotor power at higher wind speeds mainly due to inadequacies with inboard stall and stall delay models. The RaNS methodologies show promise in predicting blade stall. However, inaccurate rotor vortex wake convection, boundary layer turbulence modeling and grid resolution has limited their accuracy. In addition, the inherently unsteady stalled flow conditions become computationally expensive for even the best endowed research labs. Although numerical power predictions have been compared to experiment. The availability of good wind turbine data sufficient for code validation experimental data that has been extracted from the IEA Annex XIV download site for the NREL Combined Experiment phase II and phase IV rotor. In addition, the comparisons will show data that has been further reduced into steady wind and zero yaw conditions suitable for comparisons to "steady wind" rotor power predictions. In summary, the paper will present and discuss the capabilities and limitations of the three numerical methods and make available a database of experimental data suitable to help other numerical methods practitioners validate their own work.

  20. Biphasic kinetic investigations on the evaluation of non-salt forming reductants for Pu(IV) stripping from tributyl phosphate and N,N-dihexyl octanamide solutions in n-dodecane

    International Nuclear Information System (INIS)

    Prabhu, D.R.; Neelam Kumari; Kanekar, A.S.; Pathak, P.N.

    2013-01-01

    The relative stability of different oxidation states of actinide elements is influenced by the nature of complexes formed and redox equilibria in aqueous/non-aqueous solutions. The reduction/stripping studies on Pu(IV) ions from loaded organic phases of 1.1 M tributyl phosphate and of 1.1 M N,N-dihexyl octanamide in n-dodecane were studied using organic soluble tert-butyl hydroquinone (TBH) and aqueous soluble reductants like acetaldoxime (AX) and hydroxyurea (HU). These studies were carried out as a function of reductant and nitric acid concentration (0.5-4 M HNO 3 ) and of time. The changes in Pu oxidation states were followed by spectrophotometry for TBH and by distribution ratio values for AX and HU as reductants. Spectrophotometric investigations using TBH as reductant showed that it was desirable to strip Pu(III) formed after reduction of Pu(IV) in the organic phase, which may otherwise be reconverted to extractable Pu(IV) by in situ generated HNO 2 from oxidative degradation of TBH to tert-butyl quinone. Similarly, the biphasic reduction/stripping of Pu(IV) using AX and HU as reductant rate was affected adversely with increased aqueous phase acidity. This data will help in the accurate simulation of Pu separation processes using these reductants in mixer-settlers/pulsed columns or centrifugal contactors. (author)

  1. X-ray topographic method of investigation of phase objects

    International Nuclear Information System (INIS)

    Levonyan, L.V.

    2001-01-01

    The intensity distribution of the monochromatized synchrotron radiation transmitting through the phase object and crystal-analyzer in Laue geometry is considered. It is shown that the local angular deviation of the incident radiation caused by the refraction on structural inhomogeneities of the object under investigation is directly transferred to the X-ray topographic image. In the absence of the phase object the latter consists of parallel straight fringes with a slowly decreasing period. The presence of the phase object changes the shape and period of fringes. The influence of the spatial and temporal coherence on the image is discussed. 5 refs

  2. HATT: a phase IV, single-arm, open-label study of sorafenib in Taiwanese patients with advanced hepatocellular carcinoma.

    Science.gov (United States)

    Lin, Shi-Ming; Lu, Sheng-Nan; Chen, Ping-Tsung; Jeng, Long-Bin; Chen, Shinn-Cherng; Hu, Chi-Tan; Yang, Sien-Sing; Le Berre, Marie-Aude; Liu, Xuan; Mitchell, David Y; Prins, Klaas; Grevel, Joachim; Peña, Carol A E; Meinhardt, Gerold

    2017-03-01

    Sorafenib significantly improves survival in patients with advanced hepatocellular carcinoma (HCC). This phase IV study assessed sorafenib efficacy/safety in Taiwanese patients with advanced HCC and Child-Pugh A status. All patients received 400 mg sorafenib BID. Safety, efficacy, sorafenib pharmacokinetics, and Child-Pugh progression were evaluated. A hand-foot skin reaction (HFSR) prevention substudy assessed HFSR incidence and grade/severity and time to HFSR in 29 and 34 patients randomized to corticosteroid and noncorticosteroid ointments, respectively, and in 88 nonrandomized patients. The 151 patients included 120 (80%) male patients and 81 (54%) with stage IV disease. Mean sorafenib dose was 626 mg/day, and median treatment duration was 4.2 months. Median overall survival (OS), progression-free survival, and time to progression (TTP) were 8.6, 2.7, and 3.8 months, respectively. Disease control and response rates (partial responses only) were 48 and 6.6%, respectively. Median TTP from Child-Pugh A to B/C was 88 days. Drug-related adverse events (AEs) occurred in 89.4% of patients; none were new or unexpected. The most frequent grade ≥3 drug-related, treatment-emergent AEs were HFSR (13.2%), diarrhea (11.9%), and hypertension (6.6%). Corticosteroid ointment tended to reduce the severity and incidence of all HFSR-associated parameters. Pharmacokinetic exposure was unaltered by Child-Pugh progression. The final pharmacokinetic model predicted 13.1 and 33.8% reductions in sorafenib exposure over 6 and 12 months, respectively. There was a trend of longer OS and TTP in Taiwanese patients with advanced HCC compared with patients with advanced HCC in the Asia-Pacific trial. Sorafenib exposure did not correlate with liver function. Reduced pharmacokinetic exposure over time was unrelated to reduced or interrupted dosing.

  3. APOGEE-2: The Second Phase of the Apache Point Observatory Galactic Evolution Experiment in SDSS-IV

    Science.gov (United States)

    Sobeck, Jennifer; Majewski, S.; Hearty, F.; Schiavon, R. P.; Holtzman, J. A.; Johnson, J.; Frinchaboy, P. M.; Skrutskie, M. F.; Munoz, R.; Pinsonneault, M. H.; Nidever, D. L.; Zasowski, G.; Garcia Perez, A.; Fabbian, D.; Meza Cofre, A.; Cunha, K. M.; Smith, V. V.; Chiappini, C.; Beers, T. C.; Steinmetz, M.; Anders, F.; Bizyaev, D.; Roman, A.; Fleming, S. W.; Crane, J. D.; SDSS-IV/APOGEE-2 Collaboration

    2014-01-01

    The second phase of the Apache Point Observatory Galactic Evolution Experiment (APOGEE-2), a part of the Sloan Digital Sky Survey IV (SDSS-IV), will commence operations in 2014. APOGEE-2 represents a significant expansion over APOGEE-1, not only in the size of the stellar sample, but also in the coverage of the sky through observations in both the Northern and Southern Hemispheres. Observations on the 2.5m Sloan Foundation Telescope of the Apache Point Observatory (APOGEE-2N) will continue immediately after the conclusion of APOGEE-1, to be followed by observations with the 2.5m du Pont Telescope of the Las Campanas Observatory (APOGEE-2S) within three years. Over the six-year lifetime of the project, high resolution (R˜22,500), high signal-to-noise (≥100) spectroscopic data in the H-band wavelength regime (1.51-1.69 μm) will be obtained for several hundred thousand stars, more than tripling the total APOGEE-1 sample. Accurate radial velocities and detailed chemical compositions will be generated for target stars in the main Galactic components (bulge, disk, and halo), open/globular clusters, and satellite dwarf galaxies. The spectroscopic follow-up program of Kepler targets with the APOGEE-2N instrument will be continued and expanded. APOGEE-2 will significantly extend and enhance the APOGEE-1 legacy of scientific contributions to understanding the origin and evolution of the elements, the assembly and formation history of galaxies like the Milky Way, and fundamental stellar astrophysics.

  4. Investigation on thixojoining to produce hybrid components with intermetallic phase

    Science.gov (United States)

    Seyboldt, Christoph; Liewald, Mathias

    2018-05-01

    Current research activities at the Institute for Metal Forming Technology of the University of Stuttgart are focusing on the manufacturing of hybrid components using semi-solid forming strategies. One process investigated is the joining of different materials in the semi-solid state and is so called "thixojoining". In this process, metallic inlays are inserted into the semi-solid forming die before the actual forming process and are then joined with a material which was heated up to its semi-solid state. Earlier investigations have shown that using this process a very well-shaped form closure can be produced. Furthermore, it was found that sometimes intermetallic phases are built between the different materials, which decisively influence the part properties of such hybrid components for its future application. Within the framework presented in this paper, inlays made of aluminum, brass and steel were joined with aluminum in the semi-solid state. The aim of the investigations was to create an intermetallic bond between the different materials. For this investigations the liquid phase fraction of the aluminum and the temperature of the inlay were varied in order to determine the influence on the formation of the intermetallic phase. Forming trials were performed using a semi-solid forming die with a disk shaped design. Furthermore, the intermetallic phase built was investigated using microsections.

  5. Investigation of RuBPS-Ce(IV) chemiluminescence reaction and its application in determination of two diuretics

    Energy Technology Data Exchange (ETDEWEB)

    Xi Juan [College of Chemistry and Molecular Sciences, Wuhan University, Wuhan 430072 (China); Ji Xinghu [College of Chemistry and Molecular Sciences, Wuhan University, Wuhan 430072 (China); Zhang Shaohong [College of Chemistry and Molecular Sciences, Wuhan University, Wuhan 430072 (China); Xiang Fan Vocational and Technical College, Xiangfan 441021 (China); Ai Xinping [College of Chemistry and Molecular Sciences, Wuhan University, Wuhan 430072 (China); He Zhike [College of Chemistry and Molecular Sciences, Wuhan University, Wuhan 430072 (China)]. E-mail: zhkhe@whu.edu.cn

    2005-06-13

    The chemiluminescence mechanism of tris-(4,7-diphenyl-1,10-phenanthrolinedisulfonic acid)ruthenium(II) (RuBPS)-Ce(IV) system and the effects of two diuretics, hydrochlorothiazide and furosemide, on its chemiluminescence intensity were investigated in detail. It was found that each of the two diuretics could enhance the chemiluminescence emission intensity of RuBPS-Ce(IV) system, based on which, they were sensitively detected by chemiluminescence analysis, respectively. Under the optimum experimental conditions, the linear range and detection limit of hydrochlorothiazide were 2.5 x 10{sup -3} to 6.0 x 10{sup -1} {mu}g ml{sup -1} and 1.0 x 10{sup -3} {mu}g ml{sup -1}, respectively; those of furosemide were 1.0 x 10{sup -2} to 4.0 {mu}g ml{sup -1} and 8.8 x 10{sup -3} {mu}g ml{sup -1}, respectively. The proposed method has been applied to analyze the pharmaceuticals with satisfied results.

  6. Seismic investigation of the Kunlun Fault: Analysis of the INDEPTH IV 2-D active-source seismic dataset

    Science.gov (United States)

    Seelig, William George

    The Tibetan Plateau has experienced significant crustal thickening and deformation since the continental subduction and collision of the Asian and Indian plates in the Eocene. Deformation of the northern Tibetan Plateau is largely accommodated by strike-slip faulting. The Kunlun Fault is a 1000-km long strike-slip fault near the northern boundary of the Plateau that has experienced five magnitude 7.0 or greater earthquakes in the past 100 years and represents a major rheological boundary. Active-source, 2-D seismic reflection/refraction data, collected as part of project INDEPTH IV (International Deep Profiling of Tibet and the Himalaya, phase IV) in 2007, was used to examine the structure and the dip of the Kunlun fault. The INDEPTH IV data was acquired to better understand the tectonic evolution of the northeastern Tibetan Plateau, such as the far-field deformation associated with the continent-continent collision and the potential subduction of the Asian continent beneath northern Tibet. Seismic reflection common depth point (CDP) stacks were examined to look for reflectivity patterns that may be associated with faulting. A possible reflection from the buried North Kunlun Thrust (NKT) is identified at 18-21 km underneath the East Kunlun Mountains, with an estimated apparent dip of 15°S and thrusting to the north. Minimally-processed shot gathers were also inspected for reflections off near-vertical structures such as faults and information on first-order velocity structure. Shot offset and nearest receiver number to reflection was catalogued to increase confidence of picks. Reflections off the North Kunlun (NKF) and South Kunlun Faults (SKF) were identified and analyzed for apparent dip and subsurface geometry. Fault reflection analysis found that the North Kunlun Fault had an apparent dip of approximately 68ºS to an estimated depth of 5 km, while the South Kunlun Fault dipped at approximately 78ºN to an estimated 3.5 km depth. Constraints on apparent dip and

  7. Investigating the QCD phase diagram with hadron multiplicities at NICA

    Energy Technology Data Exchange (ETDEWEB)

    Becattini, F. [Universita di Firenze (Italy); INFN, Firenze (Italy); Stock, R. [Goethe University, Frankfurt am Main (Germany)

    2016-08-15

    We discuss the potential of the experimental programme at NICA to investigate the QCD phase diagram and particularly the position of the critical line at large baryon-chemical potential with accurate measurements of particle multiplicities. We briefly review the present status and we outline the tasks to be accomplished both theoretically and the experimentally to make hadronic abundances a sensitive probe. (orig.)

  8. Investigation of the binding of tiron to uranium(IV) and uranium(VI) found in soil

    International Nuclear Information System (INIS)

    Birnbaum, E.R.; Iams, H.D.; del Rio Garcia, M.; Ford, D.K.; Smith, P.H.; Strietelmeier, B.; Brainard, J.

    1993-01-01

    The authors are investigating the utility of a chelate-reductant system to extract uranium from 2 million yards of contaminated soil at the Fernald uranium reprocessing plant near Cincinnati, Ohio. It has been found that reduction of the uranyl contaminants using Tiron as the ligand. Of concern is whether the increased mobilization is simply a result of the higher affinity of Tiron to U(IV), or whether reduction of amorphous iron oxides contained in the soil is exposing greater amounts of uranyl ions to the ligand. It is important to establish if the latter mechanism is occurring, since a removal process which does not damage the soil is desired. Potentiometric and spectrophotometric studies of Tiron binding to soluble uranyl and U(V) salts will be presented as models to help understand the soil studies. Extraction behavior of UO 2 (OH) 2 will also be presented

  9. Readability and Content Assessment of Informed Consent Forms for Phase II-IV Clinical Trials in China.

    Science.gov (United States)

    Wen, Gaiyan; Liu, Xinchun; Huang, Lihua; Shu, Jingxian; Xu, Nana; Chen, Ruifang; Huang, Zhijun; Yang, Guoping; Wang, Xiaomin; Xiang, Yuxia; Lu, Yao; Yuan, Hong

    2016-01-01

    To explore the readability and content integrity of informed consent forms (ICFs) used in China and to compare the quality of Chinese local ICFs with that of international ICFs. The length, readability and content of 155 consent documents from phase II-IV drug clinical trials from the Third Xiangya Hospital Ethics Committee from November 2009 to January 2015 were evaluated. Reading difficulty was tested using a readability formula adapted for the Chinese language. An ICF checklist containing 27 required elements was successfully constructed to evaluate content integrity. The description of alternatives to participation was assessed. The quality of ICFs from different sponsorships were also compared. Among the 155 evaluable trials, the ICFs had a median length of 5286 words, corresponding to 7 pages. The median readability score was 4.31 (4.02-4.41), with 63.9% at the 2nd level and 36.1% at the 3rd level. Five of the 27 elements were frequently neglected. The average score for the description of alternatives to participation was 1.06, and 27.7% of the ICFs did not mention any alternatives. Compared with Chinese local ICFs, international ICFs were longer, more readable and contained more of the required elements (P readability and content integrity than Chinese local ICFs. More efforts should thus be made to improve the quality of consent documents in China.

  10. Burst pressure investigation of filament wound type IV composite pressure vessel

    Science.gov (United States)

    Farhood, Naseer H.; Karuppanan, Saravanan; Ya, H. H.; Baharom, Mohamad Ariff

    2017-12-01

    Currently, composite pressure vessels (PVs) are employed in many industries such as aerospace, transportations, medical etc. Basically, the use of PVs in automotive application as a compressed natural gas (CNG) storage cylinder has been growing rapidly. Burst failure due to the laminate failure is the most critical failure mechanism for composite pressure vessels. It is predominantly caused by excessive internal pressure due to an overfilling or an overheating. In order to reduce fabrication difficulties and increase the structural efficiency, researches and studies are conducted continuously towards the proper selection of vessel design parameters. Hence, this paper is focused on the prediction of first ply failure pressure for such vessels utilizing finite element simulation based on Tsai-Wu and maximum stress failure criterions. The effects of laminate stacking sequence and orientation angle on the burst pressure were investigated in this work for a constant layered thickness PV. Two types of winding design, A [90°2/∓θ16/90°2] and B [90°2/∓θ]ns with different orientations of helical winding reinforcement were analyzed for carbon/epoxy composite material. It was found that laminate A sustained a maximum burst pressure of 55 MPa for a sequence of [90°2/∓15°16/90°2] while the laminate B returned a maximum burst pressure of 45 MPa corresponding to a stacking sequence of [90°2/±15°/90°2/±15°/90°2/±15° ....] up to 20 layers for a constant vessel thickness. For verification, a comparison was done with the literature under similar conditions of analysis and good agreement was achieved with a maximum difference of 4% and 10% for symmetrical and unsymmetrical layout, respectively.

  11. Magnetotransport investigations of single- and heterostructure epitaxial films of IV/VI-semiconductors

    International Nuclear Information System (INIS)

    Ambrosch, K.-E.

    1985-01-01

    Lead salts are small gap semiconductors that are used for infrared detectors and lasers. PbMnTe and PbEuTe are semimagnetic semiconductors. Magnetotransport properties of epitaxial films and epitaxial heterostructures (PbTe / PbSnTe) are investigated. Epitaxial films of PbSnTe, PbMnTe and PbEuTe have been used for Shubnikov de Haas - experiments in tilted magnetic fields. This method allows the quantitative determination of the electric carrier distribution with respect to the crystal directions. The nonequal distribution is caused by strain effects that are more important for PbMnTe than for PbSnTe and PbEuTe. Magnetoresistance experiments show a deviation from cubic symmetry that leads to the same results for the carrier distribution as the Shubnikov de Haas effect. Magnetoresistance experiments performed with PbTe / PbSnTe heterostructures show no megnetoresistance if the magnetic field is in plane with the layers. The difference of the magnetoresistance for single films and heterostructures is explained by 'quasitwodimensional' carriers. Shubnikov de Haas experiments performed on heterostructures as a function of the tilt angle of the magnetic field show different behaviour compared to that of single films. Using additional information about effective masses and strain it was possible to distinguish between 'two-' and 'threedimensional' electronic systems. The distribution of carriers in single films and heterostructures has been determined by means of magnetotransport experiments. The results are explained by strain effects of the crystal lattice. In addition heterostructures show a 'quasitwodimensional' behaviour caused by interaction of their layers. (Author)

  12. A new experimental phase diagram investigation of Cu-Sb.

    Science.gov (United States)

    Fürtauer, Siegfried; Flandorfer, Hans

    The binary system Cu-Sb is a constituent system that is studied in investigations of technically important ternary and quaternary alloy systems (e.g., casting alloys and lead-free solders). Although this binary system has been thoroughly investigated over the last century, there are still some uncertainties regarding its high-temperature phases. Thus, parts of its phase diagram have been drawn with dashed lines in reviews published in the literature. The aim of this work was to resolve these uncertainties in the current phase diagram of Cu-Sb by performing XRD, SEM-EDX, EPMA, and DTA. The results from thermal analysis agreed well with those given in the literature, although some modifications due to the invariant reaction temperatures were necessary. In particular, reactions located on the Cu-rich side of the nonquenchable high-temperature β phase (BiF 3 -type) left considerable scope for interpretation. Generally, the structural descriptions of the various binary phases given in the literature were verified. The range of homogeneity of the ε phase (Cu 3 Ti type) was found to be higher on the Sb-rich side. Most of the reaction temperatures were verified, but a few had to be revised, such as the eutectoid reaction [Formula: see text] at 440 °C (found to occur at 427 °C in this work) and the eutectoid reaction [Formula: see text] at 400 °C (found to occur at 440 °C in this work). Further phase transformations that had previously only been estimated were confirmed, and their characteristic temperatures were determined.

  13. Investigation of phase stability in the scandia-zirconia

    International Nuclear Information System (INIS)

    Grosso, Robson Lopes

    2016-01-01

    In this work, the phase stability of scandia-zirconia (ScSZ) system was investigated by the thermodynamic study of nanoparticles, within the range of 0 to 20 mol% Sc 2 O 3 , and by codoping of ZrO 2 -10 mol% Sc 2 O 3 (10ScSZ) with Dy 2 O 3 and Nb 2 O 5 . The phase stability of ScSZ was evaluated based on thermodynamic data collected by water adsorption microcalorimetry and high temperature oxide melt solution. Nanostructured zirconia-scandia solid solutions were synthesized by coprecipitation method. Thermodynamic data were determined for ScSZ polymorph (monoclinic, tetragonal, cubic, rhombohedral β and γ) found by X-ray diffraction. This systemic work resulted in an unprecedented phase diagram at the nanoscale of particle size-composition. The effects of additives on 10ScSZ were investigated aiming to stabilize the cubic (c) structure at room temperature and to suppress the characteristic cubic-rhombohedral β phase transformation. Compositions were prepared by coprecipitation and solid state reaction. Materials were sintered by conventional and spark plasma sintering. Full stabilization of the cubic phase was attained by 1 mol% Dy 2 O 3 and 0.5 mol% Nb 2 O 5 additions. The smallest Nb 2 O 5 content required for cubic phase stabilization was attributed to liquid phase formation during sintering and to small ionic radius of Nb 5+ . Results of high temperature X-ray diffraction and thermal analysis show suppression of the c-β transformation. Samples containing 0.5 mol% Nb 2 O 5 show total ionic conductivity similar to 10ScSZ without additives within a broad temperature range with high stability during 170 h at 600 °C. (author)

  14. Final Work Plan: Phase I Investigation at Bladen, Nebraska

    Energy Technology Data Exchange (ETDEWEB)

    LaFreniere, Lorraine M. [Argonne National Lab. (ANL), Argonne, IL (United States). Environmental Science Division. Applied Geosciences and Environmental Management Section; Yan, Eugene [Argonne National Lab. (ANL), Argonne, IL (United States). Environmental Science Division

    2014-07-01

    The village of Bladen is a town of population approximately 237 in the northwest part of Webster County, Nebraska, 30 mi southwest of Hastings and 140 mi southwest of Lincoln, Nebraska. In 2000, the fumigant-related compound carbon tetrachloride was detected in public water supply well PWS 68-1, at a trace level. Low-level contamination, below the maximum contamination level (MCL) of 5.0 μg/L, has been detected intermittently in well PWS 68-1 since 2000, including in the last sample taken in July 2013. In 2006, the village installed a new well, PWS 2006-1, that remains free of contamination. Because the carbon tetrachloride found in well PWS 68-1 might be linked to historical use of fumigants containing carbon tetrachloride at grain storage facilities, including its former facility in Bladen, the CCC/USDA is proposing an investigation to (1) delineate the source and extent of the carbon tetrachloride contamination potentially associated with its former facility, (2) characterize pathways and controlling factors for contaminant migration in the subsurface, and (3) establish a basis for estimating potential health and environmental risks. The work will be performed in accordance with the Intergovernmental Agreement established between the NDEQ and the Farm Service Agency of the USDA. The site investigation at Bladen will be implemented in phases, so that data collected and interpretations developed during each phase can be evaluated to determine if a subsequent phase of investigation is warranted and, if warranted, to provide effective guidance for the subsequent investigation activities. This Work Plan identifies the specific technical objectives and defines the scope of work proposed for the Phase I investigation by compiling and evaluating historical data. The proposed investigation activities will be performed on behalf of the CCC/USDA by the Environmental Science Division of Argonne National Laboratory. Argonne is a nonprofit, multidisciplinary research

  15. Phase I Source Investigation, Heckathorn Superfund Site, Richmond, California

    Energy Technology Data Exchange (ETDEWEB)

    Kohn, Nancy P; Evans, Nathan R

    2002-12-18

    This report represents Phase I of a multi-phase approach to a source investigation of DDT at the Heckathorn Superfund Site, Richmond, California, the former site of a pesticide packaging plant, and the adjacent waterway, the Lauritzen Channel. Potential identified sources of contamination were from sloughed material from undredged areas (such as side banks) and from outfall pipes. Objectives of Phase I included the (1) evaluation of pesticide concentrations associated with discharge from outfalls, (2) identification of additional outfalls in the area, (3) identification of type, quantity, and distribution of sediment under the Levin pier, (4) quantification of pesticide concentrations in sediment under the pier, and (5) evaluation of sediment structure and slope stability under the pier. Field operations included the collection of sediment directly from inside the mouths of outfall pipes, when possible, or the deployment of specially designed particle traps where direct sampling was problematic. Passive water samplers were placed at the end of known outfall pipes and analyzed for DDT and other pesticides of concern. Underwater dive surveys were conducted beneath the Levin pier to document type, slope, and thickness of sediment. Samples were collected at locations of interest and analyzed for contaminants. Also sampled was soil from bank areas, which were suspected of potentially contributing to continued DDT contamination of the Lauritzen Channel through erosion and groundwater leaching. The Phase I Source Investigation was successful in identifying significant sources of DDT contamination to Lauritzen Channel sediment. Undredged sediment beneath the Levin pier that has been redistributed to the channel is a likely source. Two outfalls tested bear further investigation. Not as well-defined are the contributions of bank erosional material and groundwater leaching. Subsequent investigations will be based on the results of this first phase.

  16. An investigation of subchannel analysis models for single-phase and two-phase flow

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, Dae Hyun

    1996-01-01

    The governing equations and lateral transport modelings of subchannel analysis code, which is the most widely used tool for the analysis of thermal hydraulics fields in reactor cores, have been thoroughly investigated in this study. The procedure for the derivation of subchannel integral balance equations from the local instantaneous phase equations was investigated by stages. The characteristics of governing equations according to the treatment of phase velocity were studies, and the equations based on the drift-flux equilibrium formulation have been derived. Turbulent mixing and void drift modeling, which affect considerably to the accuracy of subchannel analysis code, have been reviewed. In addition, some representative modelings of single-phase and two-phase turbulent mixing models have been introduced. (author). 5 tabs., 4 figs., 16 refs.

  17. Post-licensure, phase IV, safety study of a live attenuated Japanese encephalitis recombinant vaccine in children in Thailand.

    Science.gov (United States)

    Chotpitayasunondh, Tawee; Pruekprasert, Pornpimol; Puthanakit, Thanyawee; Pancharoen, Chitsanu; Tangsathapornpong, Auchara; Oberdorfer, Peninnah; Kosalaraksa, Pope; Prommalikit, Olarn; Tangkittithaworn, Suwimon; Kerdpanich, Phirangkul; Techasaensiri, Chonnamet; Korejwo, Joanna; Chuenkitmongkol, Sunate; Houillon, Guy

    2017-01-05

    Japanese encephalitis is a mosquito-borne viral disease endemic in most countries in Asia. A recombinant live, attenuated Japanese encephalitis virus vaccine, JE-CV, is licensed in 14 countries, including Thailand, for the prevention of Japanese encephalitis in adults and children. This was a prospective, phase IV, open-label, multicentre, safety study of JE-CV conducted from November 2013 to April 2015, to evaluate rare serious adverse events (AEs). JE-CV was administered to 10,000 healthy children aged 9months to vaccination. Serious AEs (SAEs), including AEs of special interest, up to 60days after administration were evaluated. Immediate Grade 3 systemic AEs up to 30min after JE-CV administration were also described. The median age of participants was 1.1years in Group 1 and 3.8years in Group 2. SAEs were reported in 204 (3.0%) participants in Group 1 and 59 (1.9%) participants in Group 2. Among a total of 294 SAEs in 263 participants, only three events occurring in two participants were considered related to vaccination. All three cases were moderate urticaria, none of which met the definition of AEs of special interest for hypersensitivity. AEs of special interest were reported in 28 (0.4%) participants in Group 1 and 4 (0.1%) participants in Group 2; none were considered related to vaccination. Febrile convulsion was the most frequently reported AE of special interest: 25 (0.4%) participants in Group 1; and 2 (vaccination. Our study did not identify any new safety concerns with JE-CV and confirms its good safety profile. This study was registered on www.clinicaltrials.gov (NCT01981967; Universal Trial Number: U1111-1127-7052). Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

  18. Phase space investigation of the lithium amide halides

    Energy Technology Data Exchange (ETDEWEB)

    Davies, Rosalind A. [Hydrogen Storage Chemistry Group, School of Chemistry, University of Birmingham, Edgbaston, Birmingham B15 2TT (United Kingdom); Hydrogen and Fuel Cell Group, School of Chemical Engineering, University of Birmingham, Edgbaston B15 2TT (United Kingdom); Hewett, David R.; Korkiakoski, Emma [Hydrogen Storage Chemistry Group, School of Chemistry, University of Birmingham, Edgbaston, Birmingham B15 2TT (United Kingdom); Thompson, Stephen P. [Diamond Light Source, Harwell Science and Innovation Campus, Didcot, Oxfordshire OX11 0QX (United Kingdom); Anderson, Paul A., E-mail: p.a.anderson@bham.ac.uk [Hydrogen Storage Chemistry Group, School of Chemistry, University of Birmingham, Edgbaston, Birmingham B15 2TT (United Kingdom)

    2015-10-05

    Highlights: • The lower limits of halide incorporation in lithium amide have been investigated. • The only amide iodide stoichiometry observed was Li{sub 3}(NH{sub 2}){sub 2}I. • Solid solutions were observed in both the amide chloride and amide bromide systems. • A 46% reduction in chloride content resulted in a new phase: Li{sub 7}(NH{sub 2}){sub 6}Cl. • New low-chloride phase maintained improved H{sub 2} desorption properties of Li{sub 4}(NH{sub 2}){sub 3}Cl. - Abstract: An investigation has been carried out into the lower limits of halide incorporation in lithium amide (LiNH{sub 2}). It was found that the lithium amide iodide Li{sub 3}(NH{sub 2}){sub 2}I was unable to accommodate any variation in stoichiometry. In contrast, some variation in stoichiometry was accommodated in Li{sub 7}(NH{sub 2}){sub 6}Br, as shown by a decrease in unit cell volume when the bromide content was reduced. The amide chloride Li{sub 4}(NH{sub 2}){sub 3}Cl was found to adopt either a rhombohedral or a cubic structure depending on the reaction conditions. Reduction in chloride content generally resulted in a mixture of phases, but a new rhombohedral phase with the stoichiometry Li{sub 7}(NH{sub 2}){sub 6}Cl was observed. In comparison to LiNH{sub 2}, this new low-chloride phase exhibited similar improved hydrogen desorption properties as Li{sub 4}(NH{sub 2}){sub 3}Cl but with a much reduced weight penalty through addition of chloride. Attempts to dope lithium amide with fluoride ions have so far proved unsuccessful.

  19. Experimental and numerical investigation on two-phase flow instabilities

    Energy Technology Data Exchange (ETDEWEB)

    Ruspini, Leonardo Carlos

    2013-03-01

    Two-phase flow instabilities are experimentally and numerically studied within this thesis. In particular, the phenomena called Ledinegg instability, density wave oscillations and pressure drop oscillations are investigated. The most important investigations regarding the occurrence of two-phase flow instabilities are reviewed. An extensive description of the main contributions in the experimental and analytical research is presented. In addition, a critical discussion and recommendations for future investigations are presented. A numerical framework using a hp-adaptive method is developed in order to solve the conservation equations modelling general thermo-hydraulic systems. A natural convection problem is analysed numerically in order to test the numerical solver. Moreover, the description of an adaptive strategy to solve thermo-hydraulic problems is presented. In the second part of this dissertation, a homogeneous model is used to study Ledinegg, density wave and pressure drop oscillations phenomena numerically. The dynamic characteristics of the Ledinegg (flow excursion) phenomenon are analysed through the simulation of several transient examples. In addition, density wave instabilities in boiling and condensing systems are investigated. The effects of several parameters, such as the fluid inertia and compressibility volumes, on the stability limits of Ledinegg and density wave instabilities are studied, showing a strong influence of these parameters. Moreover, the phenomenon called pressure drop oscillations is numerically investigated. A discussion of the physical representation of several models is presented with reference to the obtained numerical results. Finally, the influence of different parameters on these phenomena is analysed. In the last part, an experimental investigation of these phenomena is presented. The designing methodology used for the construction of the experimental facility is described. Several simulations and a non

  20. An investigation of Hebbian phase sequences as assembly graphs

    Directory of Open Access Journals (Sweden)

    Daniel Gomes Almeida Filho

    2014-04-01

    Full Text Available Hebb proposed that synapses between neurons that fire synchronously are strengthened, forming cell assemblies and phase sequences. The former, on a shorter scale, are ensembles of synchronized cells that function transiently as a closed processing system; the latter, on a larger scale, correspond to the sequential activation of cell assemblies able to represent percepts and behaviors. Nowadays, the recording of large neuronal populations allows for the detection of multiple cell assemblies. Within Hebb’s theory, the next logical step is the analysis of phase sequences. Here we detected phase sequences as consecutive assembly activation patterns, and then analyzed their graph attributes in relation to behavior. We investigated action potentials recorded from the adult rat hippocampus and neocortex before, during and after novel object exploration (experimental periods. Within assembly graphs, each assembly corresponded to a node, and each edge corresponded to the temporal sequence of consecutive node activations. The sum of all assembly activations was proportional to firing rates, but the activity of individual assemblies was not. Assembly repertoire was stable across experimental periods, suggesting that novel experience does not create new assemblies in the adult rat. Assembly graph attributes, on the other hand, varied significantly across behavioral states and experimental periods, and were separable enough to correctly classify experimental periods (Naïve Bayes classifier; maximum AUROCs ranging from 0.55 to 0.99 and behavioral states (waking, slow wave sleep, and rapid eye movement sleep; maximum AUROCs s ranging from 0.64 to 0.98. Our findings agree with Hebb’s view that assemblies correspond to primitive building blocks of representation, nearly unchanged in the adult, while phase sequences are labile across behavioral states and change after novel experience. The results are compatible with a role for phase sequences in behavior

  1. Two-phase characteristics of the feeding fluid of Cerro Prieto IV wells (Mexico) obtained by gas equilibrium; Caracteristicas bifasicas del fluido de alimentacion de pozos de Cerro Prieto IV (Mexico), obtenidas por equilibrio gaseoso

    Energy Technology Data Exchange (ETDEWEB)

    Barragan-Reyes, Rosa Maria; Arellano-Gomez, Victor Manuel; Portugal-Marin, Enrique [Instituto de Investigaciones Electricas (Mexico); De Leon-Vivar, Jesus [Comision Federal de Electricidad, Residencia General de Cerro Prieto, B.C (Mexico)

    2008-10-15

    The gas composition of fluids produced by CP IV geothermal wells from the Cerro Prieto field was studied in order to identify different types of fluids entering the wells by estimating their temperature and excess steam. A method based on the Fischer Tropsch reaction and H2S equilibrium with pyrite-pyrrhotite as mineral buffer (FTHSH3) was used. The results for the reservoir natural state indicated the presence of fluids with heterogeneous reservoir temperature (between 275 and 310 degrees Celsius) and excess steam values, which were found from negative (boiled liquid that has lost steam when flowing to the well) to one (steam phase with zero liquid saturation). The study for individual wells in which boiling processes were identified, showed that through time, the feeding fluids consist of a two-phase mixture with different liquid/steam proportions. Also, the results suggested that a steam phase could occur at CP IV which is added to the feeding fluid, depending on the operation conditions of the wells. The origin of this steam could be the boiling of the deeper liquid due to a pressure drop. [Spanish] Se estudio la composicion gaseosa de los fluidos producidos por pozos geotermicos del sector CP IV del campo de Cerro Prieto para tratar de distinguir aportes de fluidos diferentes mediante la estimacion de su temperatura de yacimiento y del exceso de vapor. Se utilizo un metodo de equilibrio gaseoso basado en la reaccion de Fischer Tropsch y el equilibrio combinado pirita-pirrotita (FT-HSH3). Los resultados obtenidos indican que en el estado inicial del yacimiento existen fluidos que muestran heterogeneidad en los valores de temperatura de yacimiento (entre 275 y 310 grados Celsius), asi como en el exceso de vapor con valores desde negativos (liquido que despues de ebullir ha perdido vapor en su trayecto hacia el pozo) hasta uno (vapor con cero saturacion de liquido). El estudio individual de los pozos con fenomenos de ebullicion muestra que a traves del tiempo

  2. Investigating Earth shadowing effect with DAMA/LIBRA-phase1

    Energy Technology Data Exchange (ETDEWEB)

    Bernabei, R.; Belli, P.; D' Angelo, S.; Di Marco, A. [Universita di Roma ' ' Tor Vergata' ' , Dipt. di Fisica, Rome (Italy); INFN, sez. Roma ' ' Tor Vergata' ' , Rome (Italy); Montecchia, F. [Universita di Roma ' ' Tor Vergata' ' , Dipt. di Fisica, Rome (Italy); INFN, sez. Roma ' ' Tor Vergata' ' , Rome (Italy); Universita di Roma ' ' Tor Vergata' ' , Dipt. di Ingegneria Civile e Ingegneria Informatica, Rome (Italy); D' Angelo, A.; Incicchitti, A. [Universita di Roma ' ' La Sapienza' ' , Dipt. di Fisica, Rome (Italy); INFN, sez. Roma, Rome (Italy); Cappella, F.; Caracciolo, V.; Cerulli, R. [INFN, Laboratori Nazionali del Gran Sasso, Assergi (Italy); Dai, C.J.; He, H.L.; Kuang, H.H.; Ma, X.H.; Sheng, X.D.; Wang, R.G. [Chinese Academy of Sciences, Key Laboratory of Particle Astrophysics, Institute of High Energy Physics, Beijing (China); Ye, Z.P. [Chinese Academy of Sciences, Key Laboratory of Particle Astrophysics, Institute of High Energy Physics, Beijing (China); University of Jing Gangshan, Ji' an, Jiangxi (China)

    2015-05-15

    In the present paper the results obtained in the investigation of possible diurnal effects for low-energy single-hit scintillation events of DAMA/LIBRA-phase1 (1.04 ton x year exposure) have been analysed in terms of an effect expected in case of dark matter (DM) candidates inducing nuclear recoils and having high cross-section with ordinary matter, which implies low DM local density in order to fulfill the DAMA/LIBRA DM annual modulation results. This effect is due to the different Earth depths crossed by those DM candidates during the sidereal day. (orig.)

  3. Structural investigation of oxovanadium(IV) Schiff base complexes: X-ray crystallography, electrochemistry and kinetic of thermal decomposition.

    Science.gov (United States)

    Asadi, Mozaffar; Asadi, Zahra; Savaripoor, Nooshin; Dusek, Michal; Eigner, Vaclav; Shorkaei, Mohammad Ranjkesh; Sedaghat, Moslem

    2015-02-05

    A series of new VO(IV) complexes of tetradentate N2O2 Schiff base ligands (L(1)-L(4)), were synthesized and characterized by FT-IR, UV-vis and elemental analysis. The structure of the complex VOL(1)⋅DMF was also investigated by X-ray crystallography which revealed a vanadyl center with distorted octahedral coordination where the 2-aza and 2-oxo coordinating sites of the ligand were perpendicular to the "-yl" oxygen. The electrochemical properties of the vanadyl complexes were investigated by cyclic voltammetry. A good correlation was observed between the oxidation potentials and the electron withdrawing character of the substituents on the Schiff base ligands, showing the following trend: MeO5-H>5-Br>5-Cl. Furthermore, the kinetic parameters of thermal decomposition were calculated by using the Coats-Redfern equation. According to the Coats-Redfern plots the kinetics of thermal decomposition of studied complexes is of the first-order in all stages, the free energy of activation for each following stage is larger than the previous one and the complexes have good thermal stability. The preparation of VOL(1)⋅DMF yielded also another compound, one kind of vanadium oxide [VO]X, with different habitus of crystals, (platelet instead of prisma) and without L(1) ligand, consisting of a V10O28 cage, diaminium moiety and dimethylamonium as a counter ions. Because its crystal structure was also new, we reported it along with the targeted complex. Copyright © 2014 Elsevier B.V. All rights reserved.

  4. DSM-IV defined conduct disorder and oppositional defiant disorder: an investigation of shared liability in female twins.

    Science.gov (United States)

    Knopik, V S; Bidwell, L C; Flessner, C; Nugent, N; Swenson, L; Bucholz, K K; Madden, P A F; Heath, A C

    2014-04-01

    DSM-IV specifies a hierarchal diagnostic structure such that an oppositional defiant disorder (ODD) diagnosis is applied only if criteria are not met for conduct disorder (CD). Genetic studies of ODD and CD support a combination of shared genetic and environmental influences but largely ignore the imposed diagnostic structure. We examined whether ODD and CD share an underlying etiology while accounting for DSM-IV diagnostic specifications. Data from 1446 female twin pairs, aged 11-19 years, were fitted to two-stage models adhering to the DSM-IV diagnostic hierarchy. The models suggested that DSM-IV ODD-CD covariation is attributed largely to shared genetic influences. This is the first study, to our knowledge, to examine genetic and environmental overlap among these disorders while maintaining a DSM-IV hierarchical structure. The findings reflect primarily shared genetic influences and specific (i.e. uncorrelated) shared/familial environmental effects on these DSM-IV-defined behaviors. These results have implications for how best to define CD and ODD for future genetically informed analyses.

  5. Investigation of Polarization Phase Difference Related to Forest Fields Characterizations

    Science.gov (United States)

    Majidi, M.; Maghsoudi, Y.

    2013-09-01

    The information content of Synthetic Aperture Radar (SAR) data significantly included in the radiometric polarization channels, hence polarimetric SAR data should be analyzed in relation with target structure. The importance of the phase difference between two co-polarized scattered signals due to the possible association between the biophysical parameters and the measured Polarization Phase Difference (PPD) statistics of the backscattered signal recorded components has been recognized in geophysical remote sensing. This paper examines two Radarsat-2 images statistics of the phase difference to describe the feasibility of relationship with the physical properties of scattering targets and tries to understand relevance of PPD statistics with various types of forest fields. As well as variation of incidence angle due to affecting on PPD statistics is investigated. The experimental forest pieces that are used in this research are characterized white pine (Pinus strobus L.), red pine (Pinus resinosa Ait.), jack pine (Pinus banksiana Lamb.), white spruce (Picea glauca (Moench Voss), black spruce (Picea mariana (Mill) B.S.P.), poplar (Populus L.), red oak (Quercus rubra L.) , aspen and ground vegetation. The experimental results show that despite of biophysical parameters have a wide diversity, PPD statistics are almost the same. Forest fields distributions as distributed targets have close to zero means regardless of the incidence angle. Also, The PPD distribution are function of both target and sensor parameters, but for more appropriate examination related to PPD statistics the observations should made in the leaf-off season or in bands with lower frequencies.

  6. INVESTIGATION OF POLARIZATION PHASE DIFFERENCE RELATED TO FOREST FIELDS CHARACTERIZATIONS

    Directory of Open Access Journals (Sweden)

    M. Majidi

    2013-09-01

    Full Text Available The information content of Synthetic Aperture Radar (SAR data significantly included in the radiometric polarization channels, hence polarimetric SAR data should be analyzed in relation with target structure. The importance of the phase difference between two co-polarized scattered signals due to the possible association between the biophysical parameters and the measured Polarization Phase Difference (PPD statistics of the backscattered signal recorded components has been recognized in geophysical remote sensing. This paper examines two Radarsat-2 images statistics of the phase difference to describe the feasibility of relationship with the physical properties of scattering targets and tries to understand relevance of PPD statistics with various types of forest fields. As well as variation of incidence angle due to affecting on PPD statistics is investigated. The experimental forest pieces that are used in this research are characterized white pine (Pinus strobus L., red pine (Pinus resinosa Ait., jack pine (Pinus banksiana Lamb., white spruce (Picea glauca (Moench Voss, black spruce (Picea mariana (Mill B.S.P., poplar (Populus L., red oak (Quercus rubra L. , aspen and ground vegetation. The experimental results show that despite of biophysical parameters have a wide diversity, PPD statistics are almost the same. Forest fields distributions as distributed targets have close to zero means regardless of the incidence angle. Also, The PPD distribution are function of both target and sensor parameters, but for more appropriate examination related to PPD statistics the observations should made in the leaf-off season or in bands with lower frequencies.

  7. Experimental investigation of a two-phase nozzle flow

    International Nuclear Information System (INIS)

    Kedziur, F.; John, H.; Loeffel, R.; Reimann, J.

    1980-07-01

    Stationary two-phase flow experiments with a convergent nozzle are performed. The experimental results are appropriate to validate advanced computer codes, which are applied to the blowdown-phase of a loss-of-coolant accident (LOCA). The steam-water experiments present a broad variety of initial conditions: the pressure varies between 2 and 13 MPa, the void fraction between 0 (subcooled) and about 80%, a great number of critical as well as subcritical experiments with different flow pattern is investigated. Additional air-water experiments serve for the separation of phase transition effects. The transient acceleration of the fluid in the LOCA-case is simulated by a local acceleration in the experiment. The layout of the nozzle and the applied measurement technique allow for a separate testing of blowdown-relevant, physical models and the determination of empirical model parameters, respectively. The measured quantities are essentially the mass flow rate, quality, axial pressure and temperature profiles as well as axial and radial density/void profiles obtained by a γ-ray absorption device. Moreover, impedance probes and a pitot probe are used. Observed phenomena like a flow contraction, radial pressure and void profiles as well as the appearance of two chocking locations are described, because their examination is rather instructive about the refinement of a program. The experimental facilities as well as the data of 36 characteristic experiments are documented. (orig.) [de

  8. Enhanced Design Alternative IV

    International Nuclear Information System (INIS)

    Kramer, N.E.

    1999-01-01

    This report evaluates Enhanced Design Alternative (EDA) IV as part of the second phase of the License Application Design Selection (LADS) effort. The EDA IV concept was compared to the VA reference design using criteria from the Design Input Request for LADS Phase II EDA Evaluations (CRWMS M and O 1999b) and (CRWMS M and O 1999f). Briefly, the EDA IV concept arranges the waste packages close together in an emplacement configuration known as line load. Continuous pre-closure ventilation keeps the waste packages from exceeding their 350 C cladding and 200 C (4.3.6) drift wall temperature limits. This EDA concept keeps relatively high, uniform emplacement drift temperatures (post-closure) to drive water away from the repository and thus dry out the pillars between emplacement drifts. The waste package is shielded to permit human access to emplacement drifts and includes an integral filler inside the package to reduce the amount of water that can contact the waste form. Closure of the repository is desired 50 years after first waste is emplaced. Both backfill and drip shields will be emplaced at closure to improve post-closure performance. The EDA IV concept includes more defense-in-depth layers than the VA reference design because of its backfill, drip shield, waste package shielding, and integral filler features. These features contribute to the low dose-rate to the public achieved during the first 10,000 years of repository life as shown in Figure 3. Investigation of the EDA IV concept has led to the following general conclusions: (1) The total life cycle cost for EDA IV is about $21.7 billion which equates to a $11.3 billion net present value (both figures rounded up). (2) The incidence of design basis events for EDA IV is similar to the VA reference design. (3) The emplacement of the waste packages in drifts will be similar to the VA reference design. However, heavier equipment may be required because the shielded waste package will be heavier. (4) The heavier

  9. GASCON and MHDGAS: FORTRAN IV computer codes for calculating gas and condensed-phase compositions in the coal-fired open-cycle MHD system

    Energy Technology Data Exchange (ETDEWEB)

    Blackburn, P E

    1977-12-01

    Fortran IV computer codes have been written to calculate the equilibrium partial pressures of the gaseous phase and the quantity and composition of the condensed phases in the open-cycle MHD system. The codes are based on temperature-dependent equilibrium constants, mass conservation, the mass action law, and assumed ideal solution of compounds in each of two condensed phases. It is assumed that the phases are an oxide-silicate phase and a sulfate-carbonate-hydroxide phase. Calculations are iterated for gas and condensate concentrations while increasing or decreasing the total moles of elements, but keeping mole ratios constant, to achieve the desired total pressure. During iteration the oxygen partial pressure is incrementally changed. The decision to increase or decrease the oxygen pressure in this process depends on comparison of the oxygen content calculated in the gas and condensate phases with the initial amount of oxygen in the ash, coal, seed, and air. This process, together with a normalization step, allows the elements to converge to their initial quantities. Two versions of the computer code have been written. GASCON calculates the equilibrium gas partial pressures and the quantity and composition of the condensed phases in steps of thirteen temperature and pressure combinations in which the condensate is removed after each step, simulating continuous slag removal from the MHD system. MHDGAS retains the condensate for each step, simulating flow of condensate (and gas) through the MHD system.

  10. Sulfato Complex Formation of V(V) and V(IV) in Pyrosulfate Melts Investigated by Potentiometry and Spectroscopic Methods

    DEFF Research Database (Denmark)

    Rasmussen, Søren Birk; Eriksen, Kim Michael; Fehrmann, Rasmus

    1999-01-01

    with the oxo sulfato vanadate equilibria VO(SO4)2,2- + SO4,2- = VO(SO4)3,4- for V(IV) and (VO)2O(SO4)4,4- + 2SO4,2- = 2VO2(SO4)2,3- + S2O7,2- for V(V), and 2VO2(SO4)2,3- + SO2 + SO4,2- 2VO(SO4)3,4- for the V(V)-V(IV) redox reaction in melts saturated with sulfate. Constants for these equilibria have also been...

  11. Investigation of the explosion hazards of hydrogen sulphide. (Phase II)

    International Nuclear Information System (INIS)

    Moen, I.O.

    1986-01-01

    The results of Phase II of an investigation directed towards quantifying the explosive hazards of hydrogen sulphide in air are described. This second and final phase is focussed on flame acceleration until detonation in obstacle environments simulating a heavy water plant. The results of previous experimental tests, both small and large scale, are compiled and summarized and the results of a series of flame acceleration tests are reported. These tests were performed in order to assess the potential for damaging explosions in simulated industrial environments with repeated obstacles. The experimented apparatus consisted of a channel 1.8 m x 1.8 m in cross-section and 15.5 m long. Two obstacle configurations were tested, corresponding to 500 mm or 220 mm diameter tubes mounted across the channel at regular intervals. Tests were performed with acetylene, propane and hydrogen sulphide fuels. The results of numerical simulation are also reported and compared with the observed results. Scaling predictions are also made. The key results are summarized in the main text, and detailed reports covering the various aspects are included in three annexes

  12. Investigation of the explosion hazards of hydrogen sulphide. Phase II

    International Nuclear Information System (INIS)

    Moen, I.O.

    1986-01-01

    The results of Phase II of an investigation directed towards quantifying the explosive hazards of hydrogen sulphide in air are described. This second and final phase is focussed on flame acceleration until detonation in obstacle environments simulating a heavy water plant. The results of previous experimental tests, both small and large scale, are compiled and summarized and the results of a series of flame acceleration tests are reported. These tests were performed in order to assess the potential for damaging explosions in simulated industrial environments with repeated obstacles. The experimented apparatus consisted of a channel 1.8 m x 1.8 m in cross-section and 15.5 m long. Two obstacle configurations were tested, corresponding to 500 mm or 220 mm diameter tubes mounted across the channel at regular intervals. Tests were performed with acetylene, propane and hydrogen sulphide fuels. The results of numerical simulation are also reported and compared with the observed results. Scaling predictions are also made. The key results are summarized in the main text, and detailed reports covering the various aspects are included in three annexes

  13. Experimental Investigation of Ice Phase Change Material Heat Exchangers

    Science.gov (United States)

    Leimkuehler, Thomas O.; Stephan, Ryan A.

    2012-01-01

    Phase change materials (PCM) may be useful for spacecraft thermal control systems that involve cyclical heat loads or cyclical thermal environments. Thermal energy can be stored in the PCM during peak heat loads or in adverse thermal environments. The stored thermal energy can then be released later during minimum heat loads or in more favorable thermal environments. This can result in a decreased turndown ratio for the radiator and a reduced system mass. The use of water as a PCM rather than the more traditional paraffin wax has the potential for significant mass reduction since the latent heat of formation of water is approximately 70% greater than that of wax. One of the potential drawbacks of using ice as a PCM is its potential to rupture its container as water expands upon freezing. In order to develop a space qualified ice PCM heat exchanger, failure mechanisms must first be understood. Therefore, a methodical experimental investigation has been undertaken to demonstrate and document specific failure mechanisms due to ice expansion in the PCM. A number of ice PCM heat exchangers were fabricated and tested. Additionally, methods for controlling void location in order to reduce the risk of damage due to ice expansion were investigated. This paper presents an overview of the results of this investigation from the past three years.

  14. Investigation of switching region in superlattice phase change memories

    Science.gov (United States)

    Ohyanagi, T.; Takaura, N.

    2016-10-01

    We investigated superlattice phase change memories (PCMs) to clarify which regions were responsible for switching. We observed atomic structures in a superlattice PCM film with a stack of GeTe / Sb2Te3 layers using atomically resolved EDX maps, and we found an intermixed region with three atom species of the Ge, Sb and Te around the top GeTe layer under the top electrode. We also found that a device with a GeTe layer on an Sb2Te3 layer without superlattice structure had the same switching characteristics as a device with a superlattice PCM, that had the same top GeTe layer. We developed and fabricated a modified superlattice PCM that attained ultra low Reset / Set currents under 60 μ A .

  15. Interfacial Area and Interfacial Transfer in Two-Phase Flow Systems (Volume IV. Chapters 15-19)

    Energy Technology Data Exchange (ETDEWEB)

    Guo, T.; Park, J.; Kojasoy, G.

    2003-03-15

    Experiments were performed on horizontal air-water bubbly two-phase flow, axial flow, stratified wavy flow, and annular flow. Theoretical studies were also undertaken on interfacial parameters for a horizontal two-phase flow.

  16. Structural investigation of oxovanadium(IV) Schiff base complexes: X-ray crystallography, electrochemistry and kinetic of thermal decomposition

    Czech Academy of Sciences Publication Activity Database

    Asadi, M.; Asadi, Z.; Savaripoor, N.; Dušek, Michal; Eigner, Václav; Shorkaei, M.R.; Sedaghat, M.

    2015-01-01

    Roč. 136, Feb (2015), 625-634 ISSN 1386-1425 R&D Projects: GA ČR(CZ) GAP204/11/0809 Institutional support: RVO:68378271 Keywords : Oxovanadium(IV) complexes * Schiff base * Kinetic s of thermal decomposition * Electrochemistry Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 2.653, year: 2015

  17. DAPPA grafted polymer: an efficient solid phase extractant for U(VI), Th(IV) and La(III) from acidic waste streams and environmental samples.

    Science.gov (United States)

    Raju, Ch Siva Kesava; Subramanian, M S

    2005-07-15

    A new class of polymeric resin has been synthesized by grafting Merrifield chloromethylated resin with (dimethyl amino-phosphono-methyl)-phosphonic acid (MCM-DAPPA), for the preconcentration of U(VI), Th(IV) and La(III) from both acidic wastes and environmental samples. The various chemical modification steps involved during grafting process are characterized by FT-IR spectroscopy, (31)P and (13)C-CPMAS (cross-polarized magic angle spin) NMR spectroscopy and CHNS/O elemental analysis. The water regain capacity data for the grafted polymer are obtained from thermo-gravimetric (TG) analysis. The influence of various physico-chemical parameters during the quantitative extraction of metal ions by the resin phase are studied and optimized by both static and dynamic methods. The significant feature of this grafted polymer is its ability to extract both actinides and lanthanides from high-level acidities as well as from near neutral conditions. The resin shows very high sorption capacity values of 2.02, 0.89 and 0.54mmolg(-1) for U(VI), 1.98, 0.63 and 0.42mmolg(-1) for Th(IV) and 1.22, 0.39 and 0.39mmolg(-1) for La(III) under optimum pH, HNO(3) and HCl concentration, respectively. The grafted polymer shows faster phase exchange kinetics (99.5% recovery using 1M (NH(4))(2)CO(3), as eluent. The developed grafted resin has been successfully applied in extracting Th(IV) from high matrix monazite sand, U(VI) from sea water and also U(VI) and Th(IV) from simulated nuclear spent fuel mixtures. The analytical data obtained from triplicate measurements are within 3.9% R.S.D. reflecting the reproducibility and reliability of the developed method.

  18. Investigation on filter method for smoothing spiral phase plate

    Science.gov (United States)

    Zhang, Yuanhang; Wen, Shenglin; Luo, Zijian; Tang, Caixue; Yan, Hao; Yang, Chunlin; Liu, Mincai; Zhang, Qinghua; Wang, Jian

    2018-03-01

    Spiral phase plate (SPP) for generating vortex hollow beams has high efficiency in various applications. However, it is difficult to obtain an ideal spiral phase plate because of its continuous-varying helical phase and discontinued phase step. This paper describes the demonstration of continuous spiral phase plate using filter methods. The numerical simulations indicate that different filter method including spatial domain filter, frequency domain filter has unique impact on surface topography of SPP and optical vortex characteristics. The experimental results reveal that the spatial Gaussian filter method for smoothing SPP is suitable for Computer Controlled Optical Surfacing (CCOS) technique and obtains good optical properties.

  19. A single-arm, multicenter, safety-monitoring, phase IV study of icotinib in treating advanced non-small cell lung cancer (NSCLC).

    Science.gov (United States)

    Hu, Xingsheng; Han, Baohui; Gu, Aiqin; Zhang, Yiping; Jiao, Shun Chang; Wang, Chang-Li; He, Jintao; Jia, Xueke; Zhang, Li; Peng, Jiewen; Wu, Meina; Ying, Kejing; Wang, Junye; Ma, Kewei; Zhang, Shucai; You, Changxuan; Tan, Fenlai; Wang, Yinxiang; Ding, Lieming; Sun, Yan

    2014-11-01

    The phase 3 ICOGEN trial established the non-inferiority of icotinib to gefitinib in terms of progression-free survival (PFS) in non-small cell lung cancer (NSCLC) patients, and this led to the approval of icotinib for NSCLC by the China Food and Drug Administration. A phase 4 study was conducted to assess the safety and efficacy of icotinib in a broad range of patients with advanced NSCLC across China. This study retrospectively analyzed data from unresectable, recurrent, and/or advanced NSCLC patients who received oral icotinib 125 mg three times per day. The primary endpoint was safety. The secondary endpoints included objective response rate (ORR) and disease control rate (DCR), which were investigated overall and in subgroups such as patients with an EGFR mutation and elderly patients. Between August, 2011 and August, 2012, a total of 6087 advanced NSCLC patients were registered in this study, of which 5549 were evaluable for safety and tumor response. The median age was 63 years (range 21-95 years), and 1571 (28.3%) patients were over the age of 70. The majority of patients were non-smokers, and had adenocarcinoma and stage IV disease. The overall incidence of adverse drug reactions (ADRs) of any grade was 31.5%. The most common ADRs included rash (17.4%) and diarrhea (8.5%), and three patients experienced interstitial lung disease (ILD). The ORR and DCR were 30.0% and 80.6%, respectively, for the overall population, and 33.4% and 81.2%, 30.3% and 80.3%, and 30.4% and 89.3%, for first-line, second-line, and third-line or multiple line subsets, respectively. In 665 EGFR-mutated patients who were evaluable for tumor response, the ORR and DCR were 49.2% (327/665) and 92.3% (614/665), respectively. The data from over 6000 patients was consistent with the results of the ICOGEN study. Icotinib demonstrated a favorable toxicity profile and efficacy in the routine clinical setting. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

  20. Synthesis and characterization of surfactant immobilised layered hydrotalcite clays for the adsorption of thorium (IV) from aqueous phase: kinetics and equilibrium study

    International Nuclear Information System (INIS)

    Rijith, S.; Renju, K.; Sumi, V.S.; Shibli, S.M.A.; Anirudhan, T.S.

    2014-01-01

    Thorium is a naturally occurring radioactive element widely distributed over the earth's crust with nuclear significance. The toxic nature of this radionuclide, even at trace levels, has been a public health problem for many years. Removal of thorium (IV) from aqueous solutions with surfactant immobilised calcined hydrotalcite clays (HTS) was investigated using batch adsorption technique. Based on cost effectiveness, availability, adsorptive and regenerative properties, layered clays are reported to be excellent materials for heavy metal ions adsorption

  1. Sealing of investigation boreholes, Phase 4 - Final report

    Energy Technology Data Exchange (ETDEWEB)

    Pusch, Roland [Drawrite AB, Luleaa Technical University, Luleaa (Sweden); Ramqvist, Gunnar [El-Tekno AB, Figeholm (Sweden); Bockgaard, Niclas [Golder Associates, Goeteborg (Sweden); Ekman, Lennart [LE Geokonsult AB, Baelinge (Sweden)

    2011-09-15

    The report describes the outcome of Phase 4 of the project 'Sealing of investigation boreholes', which deals with 1) characterization and planning of borehole sealing, 2) performance and quality assessment, 3) sealing of large diameter holes, and 4) interaction of clay and concrete plugs. A specific goal was to find ways to characterize, plan and seal of boreholes so that their impact on the overall hydraulic performance of the repository rock can predicted and controlled. The work comprised selection of representative 'reference holes' at the Laxemar and Forsmark sites for development of a general programme for planning and simulating implementation of borehole plugging campaigns, considering also cost issues. A second aim was to define and quantify the role of seals in the reference holes for finding out how important sealing really is. A third was to test a practical way to seal large diameter boreholes and a fourth to find out how concrete matures and performs in contact with smectite clay. The study demonstrated, in conclusion, the need for developing techniques for preparing deep boreholes before lasting seals are installed in them, since poor sealing can short-circuit hydraulically important fracture zones intersected by the holes. The practically oriented sealing activities showed that the technique developed for tight sealing of large-diameter boreholes is practical and feasible. The issue of chemical stability was investigated by testing the performance and constitution of a plug consisting of CBI concrete in contact with smectite-rich seals for almost three years. This study showed that none of them underwent substantial degradation in this period of time, but chemical reactions and thereby generated changes in physical behaviour of the plug components had taken place, particularly in the clay. The rate of degradation is, however, not yet known. It was concluded from this study that it is suitable to carry out a corresponding

  2. Sealing of investigation boreholes, Phase 4 - Final report

    International Nuclear Information System (INIS)

    Pusch, Roland; Ramqvist, Gunnar; Bockgaard, Niclas; Ekman, Lennart

    2011-09-01

    The report describes the outcome of Phase 4 of the project 'Sealing of investigation boreholes', which deals with 1) characterization and planning of borehole sealing, 2) performance and quality assessment, 3) sealing of large diameter holes, and 4) interaction of clay and concrete plugs. A specific goal was to find ways to characterize, plan and seal of boreholes so that their impact on the overall hydraulic performance of the repository rock can predicted and controlled. The work comprised selection of representative 'reference holes' at the Laxemar and Forsmark sites for development of a general programme for planning and simulating implementation of borehole plugging campaigns, considering also cost issues. A second aim was to define and quantify the role of seals in the reference holes for finding out how important sealing really is. A third was to test a practical way to seal large diameter boreholes and a fourth to find out how concrete matures and performs in contact with smectite clay. The study demonstrated, in conclusion, the need for developing techniques for preparing deep boreholes before lasting seals are installed in them, since poor sealing can short-circuit hydraulically important fracture zones intersected by the holes. The practically oriented sealing activities showed that the technique developed for tight sealing of large-diameter boreholes is practical and feasible. The issue of chemical stability was investigated by testing the performance and constitution of a plug consisting of CBI concrete in contact with smectite-rich seals for almost three years. This study showed that none of them underwent substantial degradation in this period of time, but chemical reactions and thereby generated changes in physical behaviour of the plug components had taken place, particularly in the clay. The rate of degradation is, however, not yet known. It was concluded from this study that it is suitable to carry out a corresponding investigation of the plugs

  3. Inverse break-through investigation on uranium isotope separation in the system Fe(III) water-glycerine solution-U(IV) cathionic resin

    International Nuclear Information System (INIS)

    Murgulescu, Sanda; Calusaru, A.

    1977-01-01

    When a solution containing ferric ions passes on cationic resin in U(IV) form, the substitution of uranium by iron is preceded by oxydation of U(IV) to U(VI). During the contact of U(VI) in solution with U(IV) in resin, an exchange reaction occurs, in which 235 U is slightly concentrated in solution and 238 U in resin phase. Since increase of temperature accelerates the exchange reaction, the apparent thermodynamic values of the exchange reaction were calculated, by taking into account the variation of the apparent equilibrium constant as a function of the reciprocal value of the temperature. The corresponding thermodynamic values in both pure aqueous and water-glycerine solution are: ΔH 0 =6.45 cal.mol -1 and ΔS 0 =21.6x10 -3 cal. 0 K -1 . The use of glycerine containing solutions offers the important advantage to increase the stability versus hydrolysis of the ferric ions even at higher temperature

  4. Investigation of binary solid phases by calorimetry and kinetic modelling

    NARCIS (Netherlands)

    Matovic, M.

    2007-01-01

    The traditional methods for the determination of liquid-solid phase diagrams are based on the assumption that the overall equilibrium is established between the phases. However, the result of the crystallization of a liquid mixture will typically be a non-equilibrium or metastable state of the

  5. Examination of utility Phase 1 compliance choices and state reactions to Title IV of the Clean Air Act Amendments of 1990

    International Nuclear Information System (INIS)

    Bailey, K.A.; Elliott, T.J.; Carlson, L.J.; South, D.W.

    1993-11-01

    Title IV (acid rain) of the Clean Air Act Amendments of 1990 is imposing new limitations on the emission of sulfur dioxide (SO 2 ) and nitrogen oxides (N x ) from electric power plants. The act requires utilities to develop compliance plans to reduce these emissions, and indications are that these plans will dramatically alter traditional operating procedures. A key provision of the SO 2 control program deaned in Title IV is the creation of a system of emission allowances, with utilities having the option of complying by adjusting system emissions and allowance holdings. A compilation of SO 2 compliance activities by the 110 utility plants affected by Phase I is summarized in this report. These compliance plans are presented in a tabular form, correlated with age, capacity, and power pool data. A large number of the Phase I units (46%) have chosen to blend or switch to lower sulfur coals. This choice primarily is in response to (1) prices of low-sulfur coal and (2) the need to maintain SO 2 control flexibility because of uncertain future environmental regulations (e.g., air toxics, carbon dioxide) and compliance prices. The report also discusses the responses of state legislatures and public utility commissions to the compliance requirements in Title IV. Most states have taken negligible action regarding the regulatory treatment of allowances and compliance activities. To protect mine employment, states producing high-sulfur coal have enacted regulations encouraging continued use of that coal, but for the most part, this response has had little effect on utility compliance choices

  6. Preliminary investigation of liquid phase sintering in ferrous systems

    International Nuclear Information System (INIS)

    Klein, J.

    1975-04-01

    Liquid phase sintering was utilized to achieve, by a simple compaction and sintering procedure involving short times and moderate temperatures, a virtually full dense high carbon Fe:C alloy and high boron Fe:B alloy. Parameters such as powder characteristics and mixing, compacting pressure, heating program and the liquid phase fraction were found to influence the sintered density. The response of the Fe:C alloy to a heat treatment is reported along with preliminary experiments in the iron base ternary system Fe:W:C. Residual porosities observed in microstructures of certain liquid phase sintered compacts were accounted for by a proposed capillary flow of the liquid phase and a local densification competing against an overall densification. Some general recommendations are made for liquid phase sintering of powder aggregates. 15 fig., 7 tables

  7. Investigation on I-V for Different Heating Temperatures of Nanocomposited MEH-PPV:CNTs Organic Solar Cells

    Directory of Open Access Journals (Sweden)

    M. S. P. Sarah

    2012-01-01

    Full Text Available This paper discussed the effect of different thermal evaporation treatments for nanocomposited MEH-PPV:CNTs thin films towards the performance of organic solar cells. The configuration of the organic solar cells is ITO/MEH-PPV:CNTs/Au. The heating temperature was varied from, as deposited, 50°C, 75°C, and 100°C. From the results, we observed that the efficiency increase slightly before decreasing back at 100°C. The highest efficiency was solar cells heated at 75°C with efficiency 0.001% which is supported by the I-V characteristics and also by the absorption spectra.

  8. Experimental investigation two phase flow in direct methanol fuel cells

    International Nuclear Information System (INIS)

    Mat, M. D.; Kaplan, Y.; Celik, S.; Oeztural, A.

    2007-01-01

    Direct methanol fuel cells (DMFC) have received many attentions specifically for portable electronic applications since it utilize methanol which is in liquid form in atmospheric condition and high energy density of the methanol. Thus it eliminates the storage problem of hydrogen. It also eliminates humidification requirement of polymeric membrane which is a problem in PEM fuel cells. Some electronic companies introduced DMFC prototypes for portable electronic applications. Presence of carbon dioxide gases due to electrochemical reactions in anode makes the problem a two phase problem. A two phase flow may occur at cathode specifically at high current densities due to the excess water. Presence of gas phase in anode region and liquid phase in cathode region prevents diffusion of fuel and oxygen to the reaction sites thus reduces the performance of the system. Uncontrolled pressure buildup in anode region increases methanol crossover through membrane and adversely effect the performance. Two phase flow in both anode and cathode region is very effective in the performance of DMYC system and a detailed understanding of two phase flow for high performance DMFC systems. Although there are many theoretical and experimental studies available on the DMFC systems in the literature, only few studies consider problem as a two-phase flow problem. In this study, an experimental set up is developed and species distributions on system are measured with a gas chromatograph. System performance characteristics (V-I curves) is measured depending on the process parameters (temperature, fuel ad oxidant flow rates, methanol concentration etc)

  9. Investigation of effect of single phase electrical faults at LOFT

    International Nuclear Information System (INIS)

    Yeates, J.A.

    1978-01-01

    This LTR presents the general basic engineering facts related to an open phase fault in a three phase power system commonly referred to as a single phase condition. It describes the probable results to electrical motors and describes the LOFT system design factors which minimize the likelihood of such a fault occurring at LOFT. It recognizes that the hazard of such a fault is a realistic threat and notes the types of relays designed to provide protection. Recommendations are made to perform a detailed engineering study to determine the most advantageous protective relay design, and to implement such a design by installation of the necessary devices and controls

  10. Investigation of the phase formation from nickel coated nanostructured silicon

    Science.gov (United States)

    Shilyaeva, Yulia I.; Pyatilova, Olga V.; Berezkina, Alexandra Yu.; Sysa, Artem V.; Dudin, Alexander A.; Smirnov, Dmitry I.; Gavrilov, Sergey A.

    2016-12-01

    In this paper, the influence of the conditions of chemical and electrochemical nickel plating of nanostructured silicon and subsequent heat treatment on the phase composition of Si/Ni structures with advanced interface is studied. Nanostructured silicon formed by chemical and electrochemical etching was used for the formation of a developed interphase surface. The resulting Si/Ni samples were analyzed using scanning electron microscopy, energy dispersive X-ray analysis, and X-ray phase analysis. The experiments have revealed the differences in phase composition of the Si/Ni structures obtained by different methods, both before and after heat treatment.

  11. Investigation of alternating-phase focusing for superconducting linacs

    International Nuclear Information System (INIS)

    Sagalovsky, L.; Delayen, J.R.

    1992-01-01

    The paper describes a new model of alternating-phase focusing (APF) dynamics applicable to ion linacs with short independently controlled superconducting cavities. The equations of motion are derived for a cylindrically symmetric electric field represented by a traveling wave with continuous periodic phase modulation. Solutions are obtained and analyzed for both the linear and nonlinear particle motion. Problems of linear stability and overall longitudinal acceptance are solved using standard mathematical techniques for periodic systems; analytical results are obtained. It is shown that the main beam dynamical aspects of APF are adequately described by four parameters; equilibrium synchronous phase, phase modulation amplitude, length of APF period, and incremental energy gain. The model can be applied to study the feasibility of realizing APF in a low-β section of a proton linac. (author). 9 refs., 3 figs

  12. HRTEM investigation of phase stability in alumina–zirconia ...

    Indian Academy of Sciences (India)

    tries, at high temperatures, the small diffusion lengths involved can influence the phase stability. The present work ... a function of nanocrystalline size has been shown by Shukla ... and zirconia on a Si(100) single crystal substrate with differ-.

  13. Investigation of binary solid phases by calorimetry and kinetic modelling

    OpenAIRE

    Matovic, M.

    2007-01-01

    The traditional methods for the determination of liquid-solid phase diagrams are based on the assumption that the overall equilibrium is established between the phases. However, the result of the crystallization of a liquid mixture will typically be a non-equilibrium or metastable state of the solid. For a proper description of the crystallization process the equilibrium approach is insufficient and a kinetic approach is actually required. In this work, we show that during slow crystallizatio...

  14. A phase 2, multicenter, open-label study of sepantronium bromide (YM155) plus docetaxel in patients with stage III (unresectable) or stage IV melanoma

    International Nuclear Information System (INIS)

    Kudchadkar, Ragini; Ernst, Scott; Chmielowski, Bartosz; Redman, Bruce G; Steinberg, Joyce; Keating, Anne; Jie, Fei; Chen, Caroline; Gonzalez, Rene; Weber, Jeffrey

    2015-01-01

    Survivin is a microtubule-associated protein believed to be involved in preserving cell viability and regulating tumor cell mitosis, and it is overexpressed in many primary tumor types, including melanoma. YM155 is a first-in-class survivin suppressant. The purpose of this Phase 2 study was to evaluate the 6-month progression-free survival (PFS) rate in patients with unresectable Stage III or IV melanoma receiving a combination of YM155 plus docetaxel. The study had two parts: Part 1 established the dose of docetaxel that was tolerable in combination with YM155, and Part 2 evaluated the tolerable docetaxel dose (75 mg/m 2 ) in combination with YM155 (5 mg/m 2 per day continuous infusion over 168 h every 3 weeks). The primary endpoint was 6-month PFS rate. Secondary endpoints were objective response rate (ORR), 1-year overall survival (OS) rate, time from first response to progression, clinical benefit rate (CBR), and safety. Sixty-four patients with metastatic melanoma were treated with docetaxel and YM155. Eight patients received an initial docetaxel dose of 100 mg/m 2 and 56 patients received 75 mg/m 2 of docetaxel. Six-month PFS rate per Independent Review Committee (IRC) was 34.8% (n = 64; 95% CI, 21.3–48.6%), and per Investigator was 31.3% (n = 64; 95% CI, 19.5–43.9%). The best ORR (complete response [CR] + partial response [PR]) per IRC was 12.5% (8/64). The stable disease (SD) rate was 51.6% (33/64), leading to a CBR (CR + PR + SD) of 64.1% (41/64). Estimated probability of 1-year survival was 56.3%. YM155 is a novel agent showing modest activity when combined with docetaxel for treating patients with melanoma. YM155 was generally well tolerated, but the predetermined primary efficacy endpoint (i.e., 6-month PFS rate ≥20%) was not achieved

  15. Cold in-place recycling using solventless emulsion - phase IV (emulsion qualification and long-term field performance).

    Science.gov (United States)

    2016-05-01

    This report looks into how a successful Cold In-Place solventless emulsion behaves and how the emulsion : break test developed in Phase III of this project demonstrates that behavior. Modifications to the test have been : made to improve the consiste...

  16. Final report on the surface-based investigation phase (phase 1) at the Mizunami Underground Research Laboratory project

    International Nuclear Information System (INIS)

    Saegusa, Hiromitsu; Matsuoka, Toshiyuki

    2011-03-01

    The Mizunami Underground Research Laboratory (MIU) Project is a comprehensive research project investigating the deep underground environment within crystalline rock being conducted by Japan Atomic Energy Agency at Mizunami City in Gifu Prefecture, central Japan and its role is defined in 'Framework for Nuclear Energy Policy' by Japan Atomic Energy Commission. The MIU Project has three overlapping phases: Surface-based Investigation phase (Phase I), Construction phase (Phase II), and Operation phase (Phase III), with a total duration of 20 years. The overall project goals of the MIU Project from Phase I through to Phase III are: 1) to establish techniques for investigation, analysis and assessment of the deep geological environment, and 2) to develop a range of engineering for deep underground application. During Phase I, the overall project goals were supported by Phase I goals. For the overall project goals 1), the Phase I goals were set to construct models of the geological environment from all surface-based investigation results that describe the geological environment prior to excavation and predict excavation response. For the overall project goals 2), the Phase I goals were set to formulate detailed design concepts and a construction plan for the underground facilities. This report summarizes the Phase I investigation which was completed in March 2005. The authors believe this report will make an important milestone, since this report clarifies how the Phase I goals are achieved and evaluate the future issues thereby direct the research which will be conducted during Phase II. With regard to the overall project goals 1), 'To establish techniques for investigation, analysis and assessment of the deep geological environment,' a step-wise investigation was conducted by iterating investigation, interpretation, and assessment, thereby understanding of geologic environment was progressively and effectively improved with progress of investigation. An optimal

  17. Horonobe Underground Research Laboratory project. Synthesis of phase II (construction phase) investigations to a depth of 350 m

    International Nuclear Information System (INIS)

    Sato, Toshinori; Sasamoto, Hiroshi; Ishii, Eiichi; Matsuoka, Toshiyuki; Hayano, Akira; Miyakawa, Kazuya; Fujita, Tomoo; Tanai, Kenji; Nakayama, Masashi; Takeda, Masaki; Yokota, Hideharu; Aoyagi, Kazuhei; Ohno, Hirokazu; Shigeta, Naotaka; Hanamuro, Takahiro; Ito, Hiroaki

    2017-03-01

    The Horonobe Underground Research Laboratory (URL) Project is being pursued by the Japan Atomic Energy Agency (JAEA) to enhance the reliability of relevant disposal technologies through investigations of the deep geological environment within the host sedimentary formations at Horonobe, northern Hokkaido. The project consists of two major research areas, 'Geoscientific Research' and 'R and D on Geological Disposal', and proceeds in three overlapping phases, 'Phase I: Surface-based investigation', 'Phase II: Construction' and 'Phase III: Operation', over a period of 20 years. This report summarizes the results of the Phase II investigations carried out from April 2005 to June 2014 to a depth of 350 m. Integration of work from different disciplines into a 'geosynthesis' ensures that the Phase II goals have been successfully achieved and identifies key issues that need to be addressed in the Phase II investigations. Efforts are made to summarize as many lessons learnt from the Phase II investigations and other technical achievements as possible to form a 'knowledge base' that will reinforce the technical basis for both implementation and the formulation of safety regulations. (author)

  18. Investigations on the liquid crystalline phases of cation-induced ...

    Indian Academy of Sciences (India)

    liquid crystalline phases of Li–DNA system could be useful in the production of ... undergo unidirectional ordering (the solution starts to become birefringent under ... was spread over the glass slides with a cover slip and sealed with a neutral ...

  19. HRTEM investigation of orthorhombic phase in Mg-PSZ

    International Nuclear Information System (INIS)

    Liu, Z.W.; Spargo, A.E.C.; Hannink, R.H.J.

    1997-01-01

    Tetragonal, orthorhombic and monoclinic phases are only slight distortions of the cubic structure. Due to minor differences in unit cell parameters it is difficult to distinguish these phases only by high resolution images. However, using high resolution transmission electron microscopy (HRTEM) observation in combination with image simulation and digital Fourier transformation of HRTEM images, it was found that one tetragonal precipitate can be transformed to several orthorhombic domains with different orientations in MgO-partially-stabilized zirconia (Mg-PSZ). The lattice correspondence between two adjacent orthorhombic domains is such that their b axes are parallel, while their a axes are perpendicular to each other. Also it was found that cubic ZrO 2 could be transformed to orthorhombic ZrO 2 . 8 refs., 1 tab., 4 figs

  20. Experimental investigation of the Al-Y phase diagram

    International Nuclear Information System (INIS)

    Liu Shuhong; Du Yong; Xu Honghui; He Cuiyun; Schuster, Julius C.

    2006-01-01

    The Al-Y phase diagram has been reinvestigated with 16 key alloys over its whole composition range by means of differential thermal analysis, X-ray diffraction, optical microscopy, and scanning electron microscopy with energy dispersive X-ray techniques. The existence of five intermetallic phases, Al 3 Y, Al 2 Y, AlY, Al 2 Y 3 , and AlY 2 , has been confirmed. Al 2 Y and Al 2 Y 3 melt congruently at 1490 ± 2 and 1105 ± 2 deg. C, respectively. Al 3 Y, AlY, and AlY 2 are formed via the peritectic reactions L + Al 2 Y ↔ Al 3 Y at 980 ± 2 deg. C, L + Al 2 Y ↔ AlY at 1138 ± 2 deg. C, and L + Al 2 Y 3 ↔ AlY 2 at 977 ± 2 deg. C, respectively. Three eutectic reactions L ↔ (Al) + Al 3 Y at 637 ± 2 deg. C, L ↔ AlY + Al 2 Y 3 at 1081 ± 2 deg. C, and L ↔ AlY 2 + (αY) at 955 ± 2 deg. C , are observed. The previously reported Al 3 Y 5 , AlY 3 compounds were not found. A revised Al-Y phase diagram is presented mainly based on the present experimental results

  1. Asteroids IV

    Science.gov (United States)

    Michel, Patrick; DeMeo, Francesca E.; Bottke, William F.

    Asteroids are fascinating worlds. Considered the building blocks of our planets, many of the authors of this book have devoted their scientific careers to exploring them with the tools of our trade: ground- and spacebased observations, in situ space missions, and studies that run the gamut from theoretical modeling efforts to laboratory work. Like fossils for paleontologists, or DNA for geneticists, they allow us to construct a veritable time machine and provide us with tantalizing glimpses of the earliest nature of our solar system. By investigating them, we can probe what our home system was like before life or even the planets existed. The origin and evolution of life on our planet is also intertwined with asteroids in a different way. It is believed that impacts on the primordial Earth may have delivered the basic components for life, with biology favoring attributes that could more easily survive the aftermath of such energetic events. In this fashion, asteroids may have banished many probable avenues for life to relative obscurity. Similarly, they may have also prevented our biosphere from becoming more complex until more recent eras. The full tale of asteroid impacts on the history of our world, and how human life managed to emerge from myriad possibilities, has yet to be fully told. The hazard posed by asteroid impacts to our civilization is low but singular. The design of efficient mitigation strategies strongly relies on asteroid detection by our ground- and spacebased surveys as well as knowledge of their physical properties. A more positive motivation for asteroid discovery is that the proximity of some asteroids to Earth may allow future astronauts to harvest their water and rare mineral resources for use in exploration. A key goal of asteroid science is therefore to learn how humans and robotic probes can interact with asteroids (and extract their materials) in an efficient way. We expect that these adventures may be commonplace in the future

  2. Experimental investigation of direct contact three phase boiling heat transfer

    International Nuclear Information System (INIS)

    Bruce, W.D.

    1981-01-01

    The system which was studied in the present work consisted of one liquid undergoing vaporization by contact with a hotter immiscible liquid. The liquids and vapor were contacted in a counterflow spray column with only differential increases in vapor quality. Experiments yielded vertical temperature profiles, flow rates of the phases, liquid holdups, pressure drops, and a characterization of flow patterns. A micro-computer was utilized for measuring temperatures in the column at the rate of 1500 to 1600 times per second at several depths. Analysis of the experimental data indicate that the maximum temperature difference between the phases is 0.5F 0 , and that a temperature crossover occurs at the lower end of the column. The heat transfer fluid undergoes flash vaporization at its inlet at the top of the column, and much of its sensible heat is tranferred to the dispersed phase near the top of the column. Temperature profiles along the length of the boiler are nearly flat, and very little heat transfer occurs in the lower part of the boiler. A chemical method was developed for measuring effective interfacial area in a direct contact boiler. The theoretical basis of the method is discussed, and physico-chemical data necessary for application of the technique are reported. Water solubility of methyl salicylate was measured as a function of temperature, and the second order reaction rate coefficient for saponification of methyl salicylate by sodium hydroxide was determined from sodium hydroxide concentration versus time data and a computer model of a well-mixed semibatch reactor. The activation energy for the reaction was found to be 9.58 kilocalories per gram mole

  3. Situational Lightning Climatologies for Central Florida: Phase IV: Central Florida Flow Regime Based Climatologies of Lightning Probabilities

    Science.gov (United States)

    Bauman, William H., III

    2009-01-01

    The threat of lightning is a daily concern during the warm season in Florida. Research has revealed distinct spatial and temporal distributions of lightning occurrence that are strongly influenced by large-scale atmospheric flow regimes. Previously, the Applied Meteorology Unit (AMU) calculated the gridded lightning climatologies based on seven flow regimes over Florida for 1-, 3- and 6-hr intervals in 5-, 10-, 20-, and 30-NM diameter range rings around the Shuttle Landing Facility (SLF) and eight other airfields in the National Weather Service in Melbourne (NWS MLB) county warning area (CWA). In this update to the work, the AMU recalculated the lightning climatologies for using individual lightning strike data to improve the accuracy of the climatologies. The AMU included all data regardless of flow regime as one of the stratifications, added monthly stratifications, added three years of data to the period of record and used modified flow regimes based work from the AMU's Objective Lightning Probability Forecast Tool, Phase II. The AMU made changes so the 5- and 10-NM radius range rings are consistent with the aviation forecast requirements at NWS MLB, while the 20- and 30-NM radius range rings at the SLF assist the Spaceflight Meteorology Group in making forecasts for weather Flight Rule violations during Shuttle landings. The AMU also updated the graphical user interface with the new data.

  4. Offshore Code Comparison Collaboration within IEA Wind Task 23: Phase IV Results Regarding Floating Wind Turbine Modeling; Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Jonkman, J.; Larsen, T.; Hansen, A.; Nygaard, T.; Maus, K.; Karimirad, M.; Gao, Z.; Moan, T.; Fylling, I.

    2010-04-01

    Offshore wind turbines are designed and analyzed using comprehensive simulation codes that account for the coupled dynamics of the wind inflow, aerodynamics, elasticity, and controls of the turbine, along with the incident waves, sea current, hydrodynamics, and foundation dynamics of the support structure. This paper describes the latest findings of the code-to-code verification activities of the Offshore Code Comparison Collaboration, which operates under Subtask 2 of the International Energy Agency Wind Task 23. In the latest phase of the project, participants used an assortment of codes to model the coupled dynamic response of a 5-MW wind turbine installed on a floating spar buoy in 320 m of water. Code predictions were compared from load-case simulations selected to test different model features. The comparisons have resulted in a greater understanding of offshore floating wind turbine dynamics and modeling techniques, and better knowledge of the validity of various approximations. The lessons learned from this exercise have improved the participants' codes, thus improving the standard of offshore wind turbine modeling.

  5. Spin- and valley-dependent electrical conductivity of ferromagnetic group-IV 2D sheets in the topological insulator phase

    Science.gov (United States)

    Hoi, Bui Dinh; Yarmohammadi, Mohsen; Mirabbaszadeh, Kavoos; Habibiyan, Hamidreza

    2018-03-01

    In this work, based on the Kubo-Greenwood formalism and the k . p Hamiltonian model, the impact of Rashba spin-orbit coupling on electronic band structure and electrical conductivity of spin-up and spin-down subbands in counterparts of graphene, including silicene, stanene, and germanene nanosheets has been studied. When Rashba coupling is considered, the effective mass of Dirac fermions decreases significantly and no significant change is caused by this coupling for the subband gaps. All these nanosheets are found to be in topological insulator quantum phase at low staggered on-site potentials due to the applied perpendicular external electric field. We point out that the electrical conductivity of germanene increases gradually with Rashab coupling, while silicene and stanene have some fluctuations due to their smaller Fermi velocity. Furthermore, some critical temperatures with the same electrical conductivity values for jumping to the higher energy levels are observed at various Rashba coupling strengths. For all structures, a broad peak appears at low temperatures in electrical conductivity curves corresponding to the large entropy of systems when the thermal energy reaches to the difference between the energy states. Finally, we have reported that silicene has the larger has the larger electrical conductivity than two others.

  6. Optimising the use of marine tephrochronology in the North Atlantic: a detailed investigation of the Faroe Marine Ash Zones II, III and IV

    Science.gov (United States)

    Griggs, Adam J.; Davies, Siwan M.; Abbott, Peter M.; Rasmussen, Tine L.; Palmer, Adrian P.

    2014-12-01

    Tephrochronology is central to the INTIMATE goals for testing the degree of climatic synchroneity during abrupt climatic events that punctuated the last glacial period. Since their identification in North Atlantic marine sequences, the Faroe Marine Ash Zone II (FMAZ II), FMAZ III and FMAZ IV have received considerable attention due to their potential for high-precision synchronisation with the Greenland ice-cores. In order to optimise the use of these horizons as isochronous markers, a detailed re-investigation of their geochemical composition, sedimentology and the processes that deposited each ash zone is presented. Shard concentration profiles, geochemical homogeneity and micro-sedimentological structures are investigated for each ash zone preserved within core JM11-19PC, retrieved from the southeastern Norwegian Sea on the central North Faroe Slope. This approach allows a thorough assessment of primary ash-fall preservation and secondary depositional features and demonstrates its value for assessing depositional integrity in the marine environment. Results indicate that the FMAZ II and IV are well-resolved primary deposits that can be used as isochrons for high-precision correlation studies. We outline key recommendations for future marine tephra studies and provide a protocol for optimising the application of tephrochronology to meet the INTIMATE synchronisation goals.

  7. Structure Investigation of Ti(IV)BODOLates Involved in the Catalytic Asymmetric Reduction of Ketones Using Catecholborane

    DEFF Research Database (Denmark)

    Sarvary, Ian; Norrby, Per-Ola; Frejd, Torbjörn

    2004-01-01

    The complexes formed on mixing Ti(OiPr)4 and bicyclo-octanediols (BODOLs) 1 and 2 (1:1) are useful as chiral catalysts in asymmetric reductions and were investigated by 1HNMR-spectroscopy and by computational methods. A consistent picture emerged of head-to-tail dimers being kept together via a T...

  8. Transmission of endemic ST22-MRSA-IV on four acute hospital wards investigated using a combination of spa, dru and pulsed-field gel electrophoresis typing.

    LENUS (Irish Health Repository)

    Creamer, E

    2012-11-01

    The transmission of meticillin-resistant Staphylococcus aureus (MRSA) between individual patients is difficult to track in institutions where MRSA is endemic. We investigated the transmission of MRSA where ST22-MRSA-IV is endemic on four wards using demographic data, patient and environmental screening, and molecular typing of isolates. A total of 939 patients were screened, 636 within 72 h of admission (on admission) and 303 >72 h after admission, and 1,252 environmental samples were obtained. Isolates were typed by spa, dru and pulsed-field gel electrophoresis (PFGE) typing. A composite dendrogram generated from the three sets of typing data was used to divide isolates into \\'dendrogram groups\\' (DGs). Ten percent of patients (92\\/939) were MRSA-positive; 7 % (44\\/636) on admission and 16 % (48\\/303) >72 h after admission (p = 0.0007). MRSA was recovered from 5 % of environmental specimens (65\\/1,252). Most isolates from patients (97 %, 85\\/88) and the environment (97 %, 63\\/65) exhibited the ST22-MRSA-IV genotype. Four DGs (DG1, DG4, DG16 and DG17) accounted for 58 % of ST22-MRSA-IV isolates from patients. Epidemiological evidence suggested cross-transmission among 44\\/92 patients (48 %) but molecular typing confirmed probable cross-transmission in only 11 instances (13 %, 11\\/88), with the majority of cross-transmission (64 %; 7\\/11) occurring on one ward. In the setting of highly clonal endemic MRSA, the combination of local epidemiology, PFGE, spa and dru typing provided valuable insights into MRSA transmission.

  9. CEMS Investigations of Fe-Silicide Phases Formed by the Method of Concentration Controlled Phase Selection

    Energy Technology Data Exchange (ETDEWEB)

    Moodley, M. K.; Bharuth-Ram, K. [University of Durban-Westville, Physics Department (South Africa); Waal, H. de; Pretorius, R. [University of Stellenbosch, Physics Department (South Africa)

    2002-03-15

    Conversion electron Moessbauer spectroscopy (CEMS) measurements have been made on Fe-silicide samples formed using the method of concentration controlled phase selection. To prepare the samples a 10 nm layer of Fe{sub 30}M{sub 70} (M=Cr, Ni) was evaporated onto Si(100) surfaces, followed by evaporation of a 60 nm Fe layer. Diffusion of the Fe into the Si substrate and the formation of different Fe-Si phases was achieved by subjecting the evaporated samples to a series of heating stages, which consisted of (a) a 10 min anneal at 800 deg. C plus etch of the residual surface layer, (b) a further 3 hr anneal at 800 deg. C, (c) a 60 mJ excimer laser anneal to an energy density of 0.8 J/cm{sup 2}, and (d) a final 3 hr anneal at 800 deg. C. CEMS measurements were used to track the Fe-silicide phases formed. The CEMS spectra consisted of doublets which, based on established hyperfine parameters, could be assigned to {alpha}- or {beta}-FeSi{sub 2} or cubic FeSi. The spectra showed that {beta}-FeSi{sub 2} had formed already at the first annealing stage. Excimer laser annealing resulted in the formation of a phase with hyperfine parameters consistent with those of {alpha}-FeSi{sub 2}. A further 3 hr anneal at 800 deg. C resulted in complete reversal to the semiconducting {beta}-FeSi{sub 2} phase.

  10. MO19390 (SAiL): bleeding events in a phase IV study of first-line bevacizumab with chemotherapy in patients with advanced non-squamous NSCLC.

    Science.gov (United States)

    Dansin, Eric; Cinieri, Saverio; Garrido, Pilar; Griesinger, Frank; Isla, Dolores; Koehler, Manfred; Kohlhaeufl, Martin

    2012-06-01

    The clinical benefit and safety profile associated with first-line bevacizumab with doublet chemotherapy in patients with advanced non-squamous non-small cell lung cancer (NSCLC) was established in two large phase III studies, E4599 and AVAiL. SAiL, a single-arm phase IV study, was conducted to evaluate bevacizumab with a range of first-line chemotherapy regimens in a routine oncology practice setting. This analysis of the SAiL data was undertaken to specifically evaluate bleeding adverse events (AEs) in this study, and to explore potential associations between bleeding and baseline patient and disease characteristics. In total, 2212 patients were evaluated. Bleeding AEs (any grade) occurred in 38.2% of patients (grade ≥ 3 bleeding AEs: 3.6%). Grade ≥ 3 pulmonary hemorrhage and central nervous system bleeding events were observed in 0.7% and 0.1% of patients, respectively. The incidence of grade ≥ 3 bleeding AEs was comparable across patient subgroups defined by central tumor location, tumor cavitation, histology, concomitant anticoagulation therapy and age. The majority (88.6%) of bleeding events resolved or improved, 10.2% persisted and 1.3% led to death; 10.2% of bleeding events required bevacizumab interruption or discontinuation. This analysis from the SAiL trial reaffirms a comparable incidence of clinically significant bleeding associated with first-line bevacizumab and chemotherapy as previous phase III studies in NSCLC patients despite less stringent first-line selection criteria. Grade ≥ 3 bleeding appears to be comparable when analyzed for patient and tumor characteristics, including tumor cavitation and concomitant anticoagulation therapy. Most bleeding events resolved or improved, and interruption/discontinuation of bevacizumab was infrequent in a standard oncology practice setting. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

  11. Investigation of impurity-helium solid phase decomposition

    International Nuclear Information System (INIS)

    Boltnev, R.E.; Gordon, E.B.; Krushinskaya, I.N.; Martynenko, M.V.; Pel'menev, A.A.; Popov, E.A.; Khmelenko, V.V.; Shestakov, A.F.

    1997-01-01

    The element composition of the impurity-helium solid phase (IHSP), grown by injecting helium gas jet, involving Ne, Ar, Kr, and Xe atoms and N 2 molecules, into superfluid helium, has been studied. The measured stoichiometric ratios, S = N H e / N I m, are well over the values expected from the model of frozen together monolayer helium clusters. The theoretical possibility for the freezing of two layers helium clusters is justified in the context of the model of IHSP helium subsystem, filled the space between rigid impurity centers. The process of decomposition of impurity-helium (IH)-samples taken out of liquid helium in the temperature range 1,5 - 12 K and the pressure range 10-500 Torr has been studied. It is found that there are two stages of samples decomposition: a slow stage characterized by sample self cooling and a fast one accompanied by heat release. These results suggest, that the IHSP consists of two types of helium - weakly bound and strongly bound helium - that can be assigned to the second and the first coordination helium spheres, respectively, formed around heavy impurity particles. A tendency for enhancement of IHSP thermo stability with increasing the impurity mass is observed. Increase of helium vapor pressure above the sample causes the improvement of IH sample stability. Upon destruction of IH samples, containing nitrogen atoms, a thermoluminescence induced by atom recombination has been detected in the temperature region 3-4,5 K. This suggests that numerous chemical reactions may be realized in solidified helium

  12. High pressure MHD coal combustors investigation, phase 2

    Science.gov (United States)

    Iwata, H.; Hamberg, R.

    1981-05-01

    A high pressure MHD coal combustor was investigated. The purpose was to acquire basic design and support engineering data through systematic combustion experiments at the 10 and 20 thermal megawatt size and to design a 50 MW/sub t/ combustor. This combustor is to produce an electrically conductive plasma generated by the direct combustion of pulverized coal with hot oxygen enriched vitiated air that is seeded with potassium carbonate. Vitiated air and oxygen are used as the oxidizer, however, preheated air will ultimately be used as the oxidizer in coal fired MHD combustors.

  13. Using the Lunar Phases Concept Inventory to Investigate College Students' Pre-instructional Mental Models of Lunar Phases

    Science.gov (United States)

    Lindell, Rebecca S.; Sommer, Steven R.

    2004-09-01

    The Lunar Phases Concept Inventory (LPCI) is a twenty-item multiple-choice inventory developed to aid instructors in assessing the mental models their students utilize when answering questions concerning phases of the moon. Based upon an in-depth qualitative investigation of students' understanding of lunar phases, the LPCI was designed to take advantage of the innovative model analysis theory to probe the different dimensions of students' mental models of lunar phases. As part of a national field test, pre-instructional LPCI data was collected for over 750 students from multiple post-secondary institutions across the United States and Canada. Application of model analysis theory to this data set allowed researchers to probe the different mental models of lunar phases students across the country utilize prior to instruction. Results of this analysis display strikingly similar results for the different institutions, suggesting a potential underlying cognitive framework.

  14. Theoretical modelling and experimental investigation of single-phase and two-phase flow division at a tee-junction

    International Nuclear Information System (INIS)

    Lemonnier, H.; Hervieu, E.

    1991-01-01

    Phase separation in a tee-junction is modelled in the particular case of bubbly-flow. The model is based on a two-dimensional approach and hence, uses local equations. The first step consists in modelling the single-phase flow in the tee-junction. The free streamline theory is used to predict the flow of the continuous phase. The two recirculation zones which are presented in this case are predicted by the model. The second step consists in predicting the gas bubble paths as a result of the actions of the single-phase flow. Finally, the trajectories of gas bubbles are used to predict the separation characteristics of the tee-junction. Each step of the modelling procedure has been carefully tested by an in-depth experimental investigation. Excellent quantitative agreement is obtained between experimental results and model predictions. Moreover, the phase separation phenomenon is found to be clearly described by the model. (orig.)

  15. CST receiver tube qualification, Phase 1, Investigation - Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Mack, I.; Rossy, J.-P.

    2010-05-15

    In this report the different application possibilities for concentrated solar thermal (CST) systems are studied. Further, the possible measuring methods for characterising and qualifying the receivers with their embedded absorber tubes are investigated. The investigations show that CST systems can be used as an environmentally friendly alternative to fossil fuels in many applications. The best known one is the generation of electrical power, but concentrated solar energy can also be used for desalination, industrial process heat, and for cooling of buildings. Industrial process heat is a large potential area with temperature in the range of 120 {sup o}C to over 400 {sup o}C. Heat below 400 {sup o}C can be provided by various parabolic trough and Fresnel systems, which are optimised for the temperature required. In order to further increase the usage of CST systems, it is of great importance to provide standards for the qualification and characterisation of the different components of the CST systems. Huge efforts are currently made to define a standard for evacuated receiver tubes. For the characterisation of the black absorber tubes the development is still at the beginning, although the need here is also given. (authors)

  16. Neotectonic investigations in Southern Ontario. Prince Edward County - Phase 2

    International Nuclear Information System (INIS)

    McFall, G.H.; Allam, A.

    1991-06-01

    This report summarizes the preliminary results of geological and geophysical investigations and offshore side scan sonar surveys of the bedrock and unconsolidated sediments in Prince Edward County, Southern Ontario, by the Ontario Geological Survey in 1989. Investigations were focused on deformations in the bedrock and the surficial deposits. Some of these deformations may be neotectonic in origin. Low magnitude seismicity in the Prince Edward County region appears to be spatially related to a major regional fault system that crosses Lake Ontario and consists of the seismically active Clarendon-Linden Fault System in New York State, the Picton-Napanee and Rideau Faults, the Frontenac-Sharbot Lake Terrane Boundary and the assumed Salmon River Fault in Ontario. Detailed observations were made in the Long Point study area and the Mountain View and Picton Quarries. Bedrock structural features were documented, including: joints; normal, reverse and strike strip faults; brittle folds; and Jurassic age ultramafic dyke. Detailed refraction seismic surveys were conducted across a local fault and possible fold structures. Magnetic surveys, conducted in conjunction with the offshore side scan sonar surveys, documented large magnetic anomalies southeast of Point Petre and at the northeast end of Long Reach. Side scan sonar surveys of the lake bottom to the east of Point Petre confirm the presence of pop-ups in that area of the lake bottom which is immediately adjacent to where pop-ups are observed on land. The pop-ups present in the lake bottom have similar orientations to those mapped in the study area

  17. IVS Organization

    Science.gov (United States)

    2004-01-01

    International VLBI Service (IVS) is an international collaboration of organizations which operate or support Very Long Baseline Interferometry (VLBI) components. The goals are: To provide a service to support geodetic, geophysical and astrometric research and operational activities. To promote research and development activities in all aspects of the geodetic and astrometric VLBI technique. To interact with the community of users of VLBI products and to integrate VLBI into a global Earth observing system.

  18. A randomized phase II trial of first-line treatment with gemcitabine, erlotinib, or gemcitabine and erlotinib in elderly patients (age ≥70 years) with stage IIIB/IV non-small cell lung cancer.

    Science.gov (United States)

    Stinchcombe, Thomas E; Peterman, Amy H; Lee, Carrie B; Moore, Dominic T; Beaumont, Jennifer L; Bradford, Daniel S; Bakri, Kamal; Taylor, Mark; Crane, Jeffrey M; Schwartz, Garry; Hensing, Thomas A; McElroy, Edwin; Niell, Harvey B; Harper, Harry D; Pal, Sridhar; Socinski, Mark A

    2011-09-01

    Single-agent gemcitabine is a standard of care for elderly patients with advanced non-small cell lung cancer, but novel therapies are needed for this patient population. We performed a noncomparative randomized phase II trial of gemcitabine, erlotinib, or the combination in elderly patients (age ≥70 years) with stage IIIB or IV non-small cell lung cancer. Patients were randomized to arms: A (gemcitabine 1200 mg/m on days 1 and 8 every 21 days), B (erlotinib 150 mg daily), or C (gemcitabine 1000 mg/m on days 1 and 8 every 21 days and erlotinib 100 mg daily). Arms B and C were considered investigational; the primary objective was 6-month progression-free survival. Between March 2006 and May 2010, 146 eligible patients received protocol therapy. The majority of the patients (82%) had stage IV disease, 64% reported adenocarcinoma histology, 90% reported current or previous tobacco use, and 28% had a performance status of 2. The 6-month progression-free survival rate observed in arms A, B, and C was 22% (95% confidence interval [CI] 11-35), 24% (95% CI 13-36), and 25% (95% CI 15-38), respectively; the median overall survival observed was 6.8 months (95% CI 4.8-8.5), 5.8 months (95% CI 3.0-8.3), and 5.6 months (95% CI 3.5-8.4), respectively. The rate of grade ≥3 hematological and nonhematological toxicity observed was similar in all three arms. The best overall health-related quality of life response did not differ between treatment arms. Erlotinib or erlotinib and gemcitabine do not warrant further investigation in an unselected elderly patient population.

  19. Radiogauging to investigate two phase flow. Graduation report

    International Nuclear Information System (INIS)

    Corten, G.P.

    1992-01-01

    New measuring methods are developed and are tested with the small reactor simulator MIDAS (Mini Dodewaard ASsembly). The purpose of this work is to be able to measure accurately as many different properties of the flow as possible in the coming bigger simulator SIDAS (Simulated Dodewaard ASsembly). In SIDAS the flow around a fuel assembly of the Dutch Dodewaard reactor will be simulated. An extensive evaluation of the gamma detection system showed that the detection system could be simplified strongly. The simplified system is used to measure the radial and axial distribution of the void fraction in the core of MIDAS for three different operating conditions. Two new measuring methods have been developed and tested. A method to estimate the probability density of the void fraction in time. Due to the nonlinear relation between transmission and void fraction the determined average value of the void fraction in general will contain a systematic error. In this investigation it is shown that this error can be maximally 7.5% in MIDAS and maximally 25% in SIDAS. Therefore a new measuring method has been developed in which the true probability density of the void fraction in time is approximated by two different values of the void fraction, each with a certain probability. With this new method firstly the average void fraction can be determined much more precisely and secondly it often can be used to determine the flow pattern. (orig./WL)

  20. Radiogauging to investigate two phase flow. Graduation report

    Energy Technology Data Exchange (ETDEWEB)

    Corten, G P

    1992-11-12

    New measuring methods are developed and are tested with the small reactor simulator MIDAS (Mini Dodewaard ASsembly). The purpose of this work is to be able to measure accurately as many different properties of the flow as possible in the coming bigger simulator SIDAS (Simulated Dodewaard ASsembly). In SIDAS the flow around a fuel assembly of the Dutch Dodewaard reactor will be simulated. An extensive evaluation of the gamma detection system showed that the detection system could be simplified strongly. The simplified system is used to measure the radial and axial distribution of the void fraction in the core of MIDAS for three different operating conditions. Two new measuring methods have been developed and tested. A method to estimate the probability density of the void fraction in time. Due to the nonlinear relation between transmission and void fraction the determined average value of the void fraction in general will contain a systematic error. In this investigation it is shown that this error can be maximally 7.5% in MIDAS and maximally 25% in SIDAS. Therefore a new measuring method has been developed in which the true probability density of the void fraction in time is approximated by two different values of the void fraction, each with a certain probability. With this new method firstly the average void fraction can be determined much more precisely and secondly it often can be used to determine the flow pattern. (orig./WL).

  1. Neotectonic investigations in southern Ontario: Prince Edward County. Phase I

    International Nuclear Information System (INIS)

    McFall, G.H.; Allam, A.

    1989-03-01

    This report summarizes the preliminary results of geological and geophysical investigations of possible neotectonic features in Prince Edward County, southern Ontario, made by the Ontario Geological Survey during 1988. Low magnitude seismic events indicative of contemporary stress relief occurred during 1987-88 near Salmon Point and Consecon (M 2.2). These events were located proximal to a major regional fault system crossing Lake Ontario and consisting of the Clarendon-Linden Fault System in New York State and the Salmon River-Picton fault systems in Ontario. Detailed observations were made of regional jointing orientations (predominantly 60 degrees and 125 degrees), erosion of surficial deposits adjacent to open fractures, a local fault displacement (post-glacially), dome structures located at Point Petre, and dissolution/karst terrains in the eastern part of the study area. Excavations of four pop-up structures indicate that three are classical pop-ups and one is atypical in structure. Level transects were conducted across complex structures in the eastern part of the study area. Detailed refraction seismic and resistivity surveys were conducted on pop-up and fault features. Preliminary results indicate that the Picton Fault is a complex zone of fractures with differing bedrock on each side. The central zone of the East Duck Pond pop-up is fractured and may contain variable amounts of water. Overturned and upright folds in the Consecon Quarry located outside of the primary research area were documented and found to be trending in a west-northwest to northwest direction. This fold orientation is compatible both with a glacial shove origin and with the present stress field orientations. Although glacial shove can produce overturned folds, it cannot form upright folds. A regional, tectonic deformation oriented northeasterly is therefore suggested as the causative mechanism

  2. Investigating the phase transformations in starch during gelatinisation

    International Nuclear Information System (INIS)

    Tan, I.; Sopade, P.A.; Halley, P.J.

    2003-01-01

    amylose/amylopectin ratio of the raw starch. It was, therefore, proposed that other structural parameters such as crystallinity, lamellar assembly, water distribution inside the granules plays a critical role in the gelatinisation process. This proposition needs to be fully investigated, and small-angle scattering studies (SANS and SAXS) may provide additional information necessary to understand the mechanisms of gelatinisation and the critical parameters that affect it. In addition, this paper highlights the existing discrepancies among these mechanisms, and need for more in-depth study using advanced and novel techniques. How SANS and SAXS may aid the understanding of starch gelatinisation will also be discussed

  3. Complexation of Plutonium (IV) With Sulfate At Variable Temperatures

    International Nuclear Information System (INIS)

    Y. Xia; J.I. Friese; D.A. Moore; P.P. Bachelor; L. Rao

    2006-01-01

    The complexation of plutonium(IV) with sulfate at variable temperatures has been investigated by solvent extraction method. A NaBrO 3 solution was used as holding oxidant to maintain the plutonium(IV) oxidation state throughout the experiments. The distribution ratio of Pu(IV) between the organic and aqueous phases was found to decrease as the concentrations of sulfate were increased. Stability constants of the 1:1 and 1:2 Pu(IV)-HSO 4 - complexes, dominant in the aqueous phase, were calculated from the effect of [HSO 4 - ] on the distribution ratio. The enthalpy and entropy of complexation were calculated from the stability constants at different temperatures using the Van't Hoff equation

  4. Investigation of Thermal and Viscoelastic Properties of Polymers Relevant to Hot Melt Extrusion, IV: Affinisol™ HPMC HME Polymers.

    Science.gov (United States)

    Gupta, Simerdeep Singh; Solanki, Nayan; Serajuddin, Abu T M

    2016-02-01

    Most cellulosic polymers cannot be used as carriers for preparing solid dispersion of drugs by hot melt extrusion (HME) due to their high melt viscosity and thermal degradation at high processing temperatures. Three HME-grade hydroxypropyl methylcelluloses, namely Affinisol™ HPMC HME 15 cP, Affinisol™ HPMC HME 100 cP, and Affinisol™ HPMC HME 4 M, have recently been introduced by The Dow Chemical Co. to enable the preparation of solid dispersion at lower and more acceptable processing temperatures. In the present investigation, physicochemical properties of the new polymers relevant to HME were determined and compared with that of Kollidon(®) VA 64. Powder X-ray diffraction (PXRD), modulated differential scanning calorimetry (mDSC), thermogravimetric analysis (TGA), moisture sorption, rheology, and torque analysis by melt extrusion were applied. PXRD and mDSC showed that the Affinisol™ polymers were amorphous in nature. According to TGA, the onset of degradation for all polymers was >220°C. The Affinisol™ polymers exhibited less hygroscopicity than Kollidon(®) VA 64 and another HPMC polymer, Methocel™ K100LV. The complex viscosity profiles of the Affinisol™ polymers as a function of temperature were similar. The viscosity of the Affinisol™ polymers was highly sensitive to the shear rate applied, and unlike Kollidon(®) VA 64, the viscosity decreased drastically when the angular frequency was increased. Because of the very high shear rate encountered during melt extrusion, Affinisol™ polymers showed capability of being extruded at larger windows of processing temperatures as compared to that of Kollidon(®) VA 64.

  5. AMOS Phase IV Annual Report

    Science.gov (United States)

    1980-06-01

    Microthermal Probe System; 2) Acoustic Sounder; 3) Star Sensor; and i 4) Seeing Monitor. Thý in ..ru. cn.tat -ion, much of it one-of-a-kind prototype...profiles of C 2 N2 3) Acoustic Sounder: an instrument that measures C to 300 m altitude; 4) Microthermal Probes: two systems, consisting of three 2...atmospheric program produced - 146 - Y- MICROTHERMAL NICRPHMERI-AL PROBES (3) _j PPRBES (3) WIND SPEED & WIND SPEED & DIRECTION ---- I- DIRECTION

  6. Final report on the surface-based investigation (phase 1) at the Mizunami Underground Laboratory project

    International Nuclear Information System (INIS)

    Saegusa, Hiromitsu; Seno, Yasuhiro; Nakama, Shigeo; Tsuruta, Tadahiko; Amano, Kenji; Takeuchi, Ryuji; Matsuoka, Toshiyuki; Onoe, Hironori; Mizuno, Takashi; Ohyama, Takuya; Hama, Katsuhiro; Sato, Toshinori; Kuji, Masayoshi; Kuroda, Hidetaka; Semba, Takeshi; Uchida, Masahiro; Sugihara, Kozo; Sakamaki, Masanori; Iwatsuki, Teruki

    2007-03-01

    The Mizunami Underground Laboratory (MIU) Project is a comprehensive research project investigating the deep underground environment within crystalline rock being conducted by Japan Atomic Energy Agency at Mizunami City in Gifu Prefecture, central Japan and its role is defined in 'Framework for Nuclear Energy Policy' by Japan Atomic Energy Commission. The MIU Project has three overlapping phases: Surface-based Investigation phase (Phase I), Construction phase (Phase II), and Operation phase (Phase III), with a total duration of 20 years. The overall project goals of the MIU Project from Phase I through to Phase III are: 1) to establish techniques for investigation, analysis and assessment of the deep geological environment, and 2) to develop a range of engineering for deep underground application. During Phase I, the overall project goals were supported by Phase I goals. For the overall project goals 1), the Phase I goals were set to construct models of the geological environment from all surface-based investigation results that describe the geological environment prior to excavation and predict excavation response. For the overall project goals 2), the Phase I goals were set to formulate detailed design concepts and a construction plan for the underground facilities. This report summarizes the Phase I investigation which was completed in March 2005. The authors believe this report will make an important milestone, since this report clarifies how the Phase I goals are achieved and evaluate the future issues thereby direct the research which will be conducted during Phase II. With regard to the overall project goals 1), 'To establish techniques for investigation, analysis and assessment of the deep geological environment,' a step-wise investigation was conducted by iterating investigation, interpretation, and assessment, thereby understanding of geologic environment was progressively and effectively improved with progress of investigation. An optimal procedure from

  7. Investigation into process of solid-phase synthesis of calcium vanadates

    International Nuclear Information System (INIS)

    Fotiev, A.A.; Krasnenko, T.I.; Slobodin, B.V.

    1983-01-01

    Processes of solid-phase synthesis of calcium vanadates by Toubandt method, measuring electric conductivity and Ca 45 and V 48 radioactive indicators are investigated. It is shown that reaction diffusion during calcium vanadates production from oxides is ensured by calcium and oxygen ions or calcium ions and electrons through the product layer, as to oxygen - through the gas phase

  8. New investigation of phase equilibria in the system Al-Cu-Si.

    Science.gov (United States)

    Ponweiser, Norbert; Richter, Klaus W

    2012-01-25

    The phase equilibria and invariant reactions in the system Al-Cu-Si were investigated by a combination of optical microscopy, powder X-ray diffraction (XRD), differential thermal analysis (DTA) and electron probe micro analysis (EPMA). Isothermal phase equilibria were investigated within two isothermal sections. The isothermal section at 500 °C covers the whole ternary composition range and largely confirms the findings of previous phase diagram investigations. The isothermal section at 700 °C describes phase equilibria only in the complex Cu-rich part of the phase diagram. A new ternary compound τ was found in the region between (Al,Cu)-γ(1) and (Cu,Si)-γ and its solubility range was determined. The solubility of Al in κ-CuSi was found to be extremely high at 700 °C. In contrast, no ternary solubility in the β-phase of Cu-Al was found, although this phase is supposed to form a complete solid solution according to previous phase diagram assessments. Two isopleths, at 10 and 40 at.% Si, were investigated by means of DTA and a partial ternary reaction scheme (Scheil diagram) was constructed, based on the current work and the latest findings in the binary systems Al-Cu and Cu-Si. The current study shows that the high temperature equilibria in the Cu-rich corner are still poorly understood and additional studies in this area would be favorable.

  9. Investigation of the low flux servo-controlled limit of a co-phased interferometer

    Science.gov (United States)

    Damé, Luc; Derrien, Marc; Kozlowski, Mathias; Merdjane, Mohamed

    2018-04-01

    This paper, "Investigation of the low flux servo-controlled limit of a co-phased interferometer," was presented as part of International Conference on Space Optics—ICSO 1997, held in Toulouse, France.

  10. Investigation of Power Losses of Two-Stage Two-Phase Converter with Two-Phase Motor

    Directory of Open Access Journals (Sweden)

    Michal Prazenica

    2011-01-01

    Full Text Available The paper deals with determination of losses of two-stage power electronic system with two-phase variable orthogonal output. The simulation is focused on the investigation of losses in the converter during one period in steady-state operation. Modeling and simulation of two matrix converters with R-L load is shown in the paper. The simulation results confirm a very good time-waveform of the phase current and the system seems to be suitable for low-cost application in automotive/aerospace industries and in application with high frequency voltage sources.

  11. Horonobe Underground Research Laboratory project. Synthesis of phase I investigation 2001-2005. Volume 'geoscientific research'

    International Nuclear Information System (INIS)

    Ota, Kunio; Abe, Hironobu; Kunimaru, Takanori

    2011-03-01

    The Horonobe Underground Research Laboratory (URL) Project is being pursued by the Japan Atomic Energy Agency (JAEA) to enhance the reliability of relevant disposal technologies through investigations of the deep geological environment within the host sedimentary formations at Horonobe in Hokkaido, northern Japan. The project consists of two major research areas, 'Geoscientific Research' and 'R and D on Geological Disposal', and proceeds in three overlapping phases, 'Phase I: Surface-based investigation', 'Phase II: Construction' and 'Phase III: Operation', over a period of 20 years. The present report summarises the results of the Phase I geoscientific research carried out from March 2001 to March 2005. Integration of the results from different disciplines ensures that the Phase I goals have been successfully achieved and identifies key issues that need to be addressed in Phases II and III. More importantly, efforts are made to summarise as many lessons learnt from the Phase I investigations and other technical achievements as possible to form a 'knowledge base' that will reinforce the technical basis for both implementation and the formulation of safety regulations. Based on experiences of selecting the URL area and site in Horonobe Town, important factors that should be taken into consideration in such selection processes and their rationale are demonstrated. In the course of stepwise surface-based investigations, a number of achievements have been made, which can eventually provide examples of integrated methodologies for characterising the sedimentary formations. The relevant surface-based investigation techniques have thus been further developed. The Horonobe URL has been designed based on geoscientific information accumulated during the surface-based investigations and the plans for safe construction and operation of the URL have been defined in a feasible manner. In addition, a variety of environmental measures taken during Phase I have proved to be

  12. Improvements in critical dosimetric endpoints using the Contura multilumen balloon breast brachytherapy catheter to deliver accelerated partial breast irradiation: preliminary dosimetric findings of a phase iv trial.

    Science.gov (United States)

    Arthur, Douglas W; Vicini, Frank A; Todor, Dorin A; Julian, Thomas B; Lyden, Maureen R

    2011-01-01

    Dosimetric findings in patients treated with the Contura multilumen balloon (MLB) breast brachytherapy catheter to deliver accelerated partial breast irradiation (APBI) on a multi-institutional Phase IV registry trial are presented. Computed tomography-based three-dimensional planning with dose optimization was performed. For the trial, new ideal dosimetric goals included (1) ≥95% of the prescribed dose (PD) covering ≥90% of the target volume, (2) a maximum skin dose ≤125% of the PD, (3) maximum rib dose ≤145% of the PD, and (4) the V150 ≤50 cc and V200 ≤10 cc. The ability to concurrently achieve these dosimetric goals using the Contura MLB was analyzed. 144 cases were available for review. Using the MLB, all dosimetric criteria were met in 76% of cases. Evaluating dosimetric criteria individually, 92% and 89% of cases met skin and rib dose criteria, respectively. In 93% of cases, ideal target volume coverage goals were met, and in 99%, dose homogeneity criteria (V150 and V200) were satisfied. When skin thickness was ≥5 mm to <7 mm, the median skin dose was limited to 120.1% of the PD, and when skin thickness was <5 mm, the median skin dose was 124.2%. When rib distance was <5 mm, median rib dose was reduced to 136.5% of the PD. When skin thickness was <7 mm and distance to rib was <5 mm, median skin and rib doses were jointly limited to 120.6% and 142.1% of the PD, respectively. The Contura MLB catheter provided the means of achieving the imposed higher standard of dosimetric goals in the majority of clinical scenarios encountered. Copyright © 2011 Elsevier Inc. All rights reserved.

  13. Feasibility and effectiveness of the implementation of a primary prevention programme for type 2 diabetes in routine primary care practice: a phase IV cluster randomised clinical trial

    Directory of Open Access Journals (Sweden)

    Sanchez Alvaro

    2012-11-01

    Full Text Available Abstract Background The objective of this study is to perform an independent evaluation of the feasibility and effectiveness of an educational programme for the primary prevention of type 2 diabetes (DM2 in high risk populations in primary care settings, implanted within the Basque Health Service - Osakidetza. Methods/design This is a prospective phase IV cluster clinical trial conducted under routine conditions in 14 primary health care centres of Osakidetza, randomly assigned to an intervention or control group. We will recruit a total sample of 1089 individuals, aged between 45 and 70 years old, without diabetes but at high risk of developing the condition (Finnish Diabetes Risk Score, FINDRISC ≥ 14 and follow them up for 2 years. Primary health care nursing teams of the intervention centres will implement DE-PLAN, a structured educational intervention program focused on changing healthy lifestyles (diet and physical activity; while the patients in the control centres will receive the usual care for the prevention and treatment of DM2 currently provided in Osakidetza. The effectiveness attributable to the programme will be assessed by comparing the changes observed in patients exposed to the intervention and those in the control group, with respect to the risk of developing DM2 and lifestyle habits. In terms of feasibility, we will assess indicators of population coverage and programme implementation. Discussion The aim of this study is to provide the scientific basis for disseminate the programme to the remaining primary health centres in Osakidetza, as a novel way of addressing prevention of DM2. The study design will enable us to gather information on the effectiveness of the intervention as well as the feasibility of implementing it in routine practice. Trial registration ClinicalTrials.gov NCT01365013

  14. Safety and Efficacy of PDpoetin for Management of Anemia in Patients with end Stage Renal Disease on Maintenance Hemodialysis: Results from a Phase IV Clinical Trial.

    Science.gov (United States)

    Javidan, Abbas Norouzi; Shahbazian, Heshmatollah; Emami, Amirhossein; Yekaninejad, Mir Saeed; Emami-Razavi, Hassan; Farhadkhani, Masoumeh; Ahmadzadeh, Ahmad; Gorjipour, Fazel

    2014-08-26

    Recombinant human erythropoietin (rHuEPO) is available for correcting anemia. PDpoetin, a new brand of rHuEPO, has been certified by Food and Drug Department of Ministry of Health and Medical Education of Iran for clinical use in patients with chronic kidney disease. We conducted this post-marketing survey to further evaluate the safety and efficacy of PDpoetin for management of anemia in patients on maintenance hemodialysis. Patients from 4 centers in Iran were enrolled for this multicenter, open-label, uncontrolled phase IV clinical trial. Changes in blood chemistry, hemoglobin and hematocrit levels, renal function, and other characteristics of the patients were recorded for 4 months; 501 of the patients recruited, completed this study. Mean age of the patients was 50.9 (±16.2) years. 48.7% of patients were female. Mean of the hemoglobin value in all of the 4 centers was 9.29 (±1.43) g/dL at beginning of the study and reached 10.96 (±2.23) g/dL after 4 months and showed significant increase overall (Pcase of immunological reactions to PDpoetin was observed. Our study, therefore, showed that PDpoetin has significantly raised the level of hemoglobin in the hemodialysis patients (about 1.7±0.6 g/dL). Anemia were successfully corrected in 49% of patients under study. Use of this biosimilar was shown to be safe and effective for the maintenance of hemoglobin in patients on maintenance hemodialysis.

  15. Safety and efficacy of PDpoetin for management of anemia in patients with end stage renal disease on maintenance hemodialysis: results from a phase IV clinical trial

    Directory of Open Access Journals (Sweden)

    Abbas Norouzi Javidan

    2014-09-01

    Full Text Available Recombinant human erythropoietin (rHuEPO is available for correcting anemia. PDpoetin, a new brand of rHuEPO, has been certified by Food and Drug Department of Ministry of Health and Medical Education of Iran for clinical use in patients with chronic kidney disease. We conducted this post-marketing survey to further evaluate the safety and efficacy of PDpoetin for management of anemia in patients on maintenance hemodialysis. Patients from 4 centers in Iran were enrolled for this multicenter, open-label, uncontrolled phase IV clinical trial. Changes in blood chemistry, hemoglobin and hematocrit levels, renal function, and other characteristics of the patients were recorded for 4 months; 501 of the patients recruited, completed this study. Mean age of the patients was 50.9 (±16.2 years. 48.7% of patients were female. Mean of the hemoglobin value in all of the 4 centers was 9.29 (±1.43 g/dL at beginning of the study and reached 10.96 (±2.23 g/dL after 4 months and showed significant increase overall (P<0.001. PDpoetin dose was stable at 50-100 U/kg thrice weekly. Hemorheologic disturbancesand changes in blood electrolytes was not observed. No case of immunological reactions to PDpoetin was observed. Our study, therefore, showed that PDpoetin has significantly raised the level of hemoglobin in the hemodialysis patients (about 1.7±0.6 g/dL. Anemia were successfully corrected in 49% of patients under study. Use of this biosimilar was shown to be safe and effective for the maintenance of hemoglobin in patients on maintenance hemodialysis.

  16. Experimental investigation of the phase equilibria in the Co-Fe-Ti ternary system

    Energy Technology Data Exchange (ETDEWEB)

    Yuan, Chaohui; Chen, Chong; Peng, Yingbiao; Du, Yong; Li, Kun [Central South Univ., State Key of Powder Metallurgy, Changsha (China); Lu, Xingxu [Central South Univ., State Key of Powder Metallurgy, Changsha (China); Central South Univ., School of Materials Science and Engineering, Changsha (China)

    2015-08-15

    Phase equilibria in the Co-Fe-Ti ternary system were investigated by means of the equilibrated alloy method with X-ray powder diffraction and electron probe microanalysis. No ternary compounds were found. The experimental results indicated the existence of seven two-phase and one three-phase regions at 600 C, five two-phase and two three-phase regions at 800 C, and six two-phase and two three-phase regions at 950 C. The solubility of Co in TiFe{sub 2} was determined to be larger than 54 at.% at all investigated temperatures, and the solubilities of Fe in TiCo{sub 3} and Ti{sub 2}Co showed an appreciable increase with increasing temperature. The three-phase equilibrium in the Ti-rich corner at 800 C was revealed to be ((β-Ti) + Ti(Fe, Co) + Ti{sub 2}Co) rather than ((α-Ti) + Ti(Fe, Co) + Ti{sub 2}Co) reported in previous investigations. Based on the experimental data obtained in the present work, three isothermal sections at 600, 800 and 950 C were established.

  17. Hepatic imaging in stage IV-S neuroblastoma

    International Nuclear Information System (INIS)

    Franken, E.A. Jr.; Smith, W.L.; Iowa Univ., Iowa City; Cohen, M.D.; Kisker, C.T.; Platz, C.E.

    1986-01-01

    Stage IV-S neuroblastoma describes a group of infants with tumor spread limited to liver, skin, or bone marrow. Such patients, who constitute about 25% of affected infants with neuroblastoma, may expect spontaneous tumor remission. We report 18 infants with Stage IV-S neuroblastoma, 83% of whom had liver involvement. Imaging investigations included Technetium 99m sulfur colloid scan, ultrasound, and CT. Two patterns of liver metastasis were noted: ill-defined nodules or diffuse tumor throughout the liver. Distinction of normal and abnormal liver with diffuse type metastasis could be quite difficult, particularly with liver scans. We conclude that patients with Stage IV-S neuroblastoma have ultrasound or CT examination as an initial workup, with nuclear medicine scans reserved for followup studies. (orig.)

  18. Phase 2 Study of Docetaxel, Cisplatin, and Concurrent Radiation for Technically Resectable Stage III-IV Squamous Cell Carcinoma of the Head and Neck

    Energy Technology Data Exchange (ETDEWEB)

    Inohara, Hidenori, E-mail: hinohara@ent.med.osaka-u.ac.jp [Department of Otorhinolaryngology—Head and Neck Surgery, Osaka University Faculty of Medicine, Suita, Osaka (Japan); Takenaka, Yukinori; Yoshii, Tadashi; Nakahara, Susumu; Yamamoto, Yoshifumi; Tomiyama, Yoichiro [Department of Otorhinolaryngology—Head and Neck Surgery, Osaka University Faculty of Medicine, Suita, Osaka (Japan); Seo, Yuji; Isohashi, Fumiaki; Suzuki, Osamu; Yoshioka, Yasuo; Sumida, Iori; Ogawa, Kazuhiko [Department of Radiation Oncology, Osaka University Faculty of Medicine, Suita, Osaka (Japan)

    2015-04-01

    Purpose: We investigated the efficacy and safety of weekly low-dose docetaxel and cisplatin therapy concurrent with conventionally fractionated radiation in patients with technically resectable stage III-IV squamous cell carcinoma of the head and neck. Methods and Materials: Between March 2004 and October 2011, we enrolled 117 patients, of whom 116 were analyzable (43 had oropharyngeal cancer, 54 had hypopharyngeal cancer, and 19 had laryngeal cancer), and 85 (73%) had stage IV disease. Radiation consisted of 66 Gy in 33 fractions. Docetaxel, 10 mg/m{sup 2}, followed by cisplatin, 20 mg/m{sup 2}, administered on the same day were given once a week for 6 cycles. The primary endpoint was overall complete response (CR) rate after chemoradiation therapy. Human papillomavirus (HPV) DNA in oropharyngeal cancer was examined by PCR. Results: Of 116 patients, 82 (71%) completed treatment per protocol; 102 (88%) received the full radiation therapy dose; and 90 (78%) and 12 (10%) patients received 6 and 5 chemotherapy cycles, respectively. Overall CR rate was 71%. After median follow-up of 50.9 months (range: 15.6-113.9 months for surviving patients), 2-year and 4-year overall survival rates were 82% and 68%, respectively. Cumulative 2-year and 4-year local failure rates were 27% and 28%, respectively, whereas distant metastasis rates were 15% and 22%, respectively. HPV status in oropharyngeal cancer was not associated with treatment efficacy. Acute toxicity included grade 3 and 4 in-field mucositis in 73% and 5% of patients, respectively, whereas myelosuppression and renal injury were minimal. No patients died of toxicity. Feeding tube dependence in 8% and tracheostomy in 1% of patients were evident at 2 years postchemoradiation therapy in patients who survived without local treatment failure. Conclusions: Local control and survival with this regimen were satisfactory. Although acute toxicity, such as mucositis, was common, late toxicity, such as laryngoesophageal

  19. Phase II Study of HER-2/neu Intracellular Domain Peptide-Based Vaccine Administered to Stage IV HER2 Positive Breast Cancer Patients Receiving Trastuzumab

    National Research Council Canada - National Science Library

    Disis, Mary L

    2007-01-01

    The primary purpose of this grant is to determine the overall survival benefit in Stage IV HER2 positive breast cancer patients vaccinated with a HER2 ICD peptide-based vaccine while receiving maintenance trastuzumab...

  20. Phase II Study of HER-2/neu Intracellular Domain Peptide-Based Vaccine Administered to Stage IV HER2 Positive Breast Cancer Patients Receiving Trastuzumab

    National Research Council Canada - National Science Library

    Disis, Mary L

    2006-01-01

    The primary purpose of this grant is to determine the overall survival benefit in Stage IV HER2 positive breast cancer patients vaccinated with a HER2 ICD peptide-based vaccine while receiving maintenance trastuzumab...

  1. Advanced Gastric Cancer: Differentiation of Borrmann Type IV versus Borrmann Type III by Two-Phased Dynamic Multi-Detector Row CT with Use of the Water Filling Method

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Dae Jung; Yu, Jeong Sik; Lee, Sang Min; Kim, Joo Hee; Chung, Jae Joon; Kim, Ki Whang [Dept. of Radiology, Yonsei University College of Medicine, Gangnam Severance Hospital, Seoul (Korea, Republic of); Kang, Hae Youn [CHA Bundang Medical Center, CHA University, Seongnam (Korea, Republic of)

    2013-02-15

    To characterize Borrmann type IV from Borrmann type III advanced gastric cancer (AGC) by two-phased multi-detector row computed tomography (MDCT) using the water filling method. A total of 143 patients (pathologically confirmed Borrmann type III and IV - 100 and 43 patients), who underwent preoperative MDCT, were enrolled. Two radiologists, retrospectively and independently, determined tumor enhancement pattern using a 5-grade scale without clinical information. A weighted kappa test was applied for interobserver variability. The score of tumor enhancement pattern correlated with Borrmann type as determined by Spearman's correlation coefficient. The accuracy of differentiation of Borrmann type using MDCT was determined by receiver operating characteristic curves. Interobserver agreement (weighted kappa = 0.683) was substantial. The tumor enhancement pattern score showed a significant correlation with Borrmann type (reviewer 1, r = 0.591, p < 0.001; reviewer 2, r = 0.616, p < 0.001). The accuracy for differentiation of Borrmann type on MDCT was 0.86 (p < 0.001) in both reviewers. The sensitivity and specificity of the diagnosis of Borrmann type IV were 79% and 82% in reviewer 1, and 88% and 78% in reviewer 2, respectively. Dual-phased MDCT using the water filling method can differentiate between Borrmann type IV and III AGC with high accuracy.

  2. Investigating the Capability of IRS-P6-LISS IV Satellite Image for Pistachio Forests Density Mapping (case Study: Northeast of Iran)

    Science.gov (United States)

    Hoseini, F.; Darvishsefat, A. A.; Zargham, N.

    2012-07-01

    In order to investigate the capability of satellite images for Pistachio forests density mapping, IRS-P6-LISS IV data were analyzed in an area of 500 ha in Iran. After geometric correction, suitable training areas were determined based on fieldwork. Suitable spectral transformations like NDVI, PVI and PCA were performed. A ground truth map included of 34 plots (each plot 1 ha) were prepared. Hard and soft supervised classifications were performed with 5 density classes (0-5%, 5-10%, 10-15%, 15-20% and > 20%). Because of low separability of classes, some classes were merged and classifications were repeated with 3 classes. Finally, the highest overall accuracy and kappa coefficient of 70% and 0.44, respectively, were obtained with three classes (0-5%, 5-20%, and > 20%) by fuzzy classifier. Considering the low kappa value obtained, it could be concluded that the result of the classification was not desirable. Therefore, this approach is not appropriate for operational mapping of these valuable Pistachio forests.

  3. Investigation of the factor structure of the Wechsler Adult Intelligence Scale--Fourth Edition (WAIS-IV): exploratory and higher order factor analyses.

    Science.gov (United States)

    Canivez, Gary L; Watkins, Marley W

    2010-12-01

    The present study examined the factor structure of the Wechsler Adult Intelligence Scale--Fourth Edition (WAIS-IV; D. Wechsler, 2008a) standardization sample using exploratory factor analysis, multiple factor extraction criteria, and higher order exploratory factor analysis (J. Schmid & J. M. Leiman, 1957) not included in the WAIS-IV Technical and Interpretation Manual (D. Wechsler, 2008b). Results indicated that the WAIS-IV subtests were properly associated with the theoretically proposed first-order factors, but all but one factor-extraction criterion recommended extraction of one or two factors. Hierarchical exploratory analyses with the Schmid and Leiman procedure found that the second-order g factor accounted for large portions of total and common variance, whereas the four first-order factors accounted for small portions of total and common variance. It was concluded that the WAIS-IV provides strong measurement of general intelligence, and clinical interpretation should be primarily at that level.

  4. Experimental investigation of phase equilibria in the Nb-Si-Ta ternary system

    Energy Technology Data Exchange (ETDEWEB)

    Li, Jian; Wang, Cuiping; Yao, Jun; Yang, Shuiyuan; Zhan Shi; Liu, Xingjun [Xiamen Univ. (China). Dept. of Materials Science and Engineering; Xiamen Univ. (China). Fujian Provincial Key Laboratory of Materials Genome; Kang, Yongwang [Beijing Institute of Aeronautical Materials (China). Science and Technology on Advanced High Temperature Structural Materials Lab.

    2016-12-15

    The phase equilibria in the Nb-Si-Ta ternary system at 1 373 K, 1 473 K and 1 573 K were investigated by means of back-scattered electron imaging, electron probe microanalysis and X-ray diffraction. The isothermal sections at 1 373 K, 1 473 K and 1 573 K consist of two three-phase regions and seven two-phase regions, without any ternary compounds. The compounds of NbSi{sub 2} and TaSi{sub 2}, αNb{sub 5}Si{sub 3} and αTa{sub 5}Si{sub 3} form continuous solid solutions, respectively. The solubilities of Nb in Ta{sub 3}Si and Ta{sub 2}Si phases are extremely large, whereas the solubility of Si in the β(Nb, Ta) phase is relatively small.

  5. A randomized, double-blind, cross-over, phase IV trial of oros-methylphenidate (CONCERTA(®)) and generic novo-methylphenidate ER-C (NOVO-generic).

    Science.gov (United States)

    Fallu, Angelo; Dabouz, Farida; Furtado, Melissa; Anand, Leena; Katzman, Martin A

    2016-08-01

    Attention-deficit/hyperactivity disorder (ADHD) is a common neurobehavioral disorder with onset during childhood. Multiple aspects of a child's development are hindered, in both home and school settings, with negative impacts on social, emotional, and cognitive functioning. If left untreated, ADHD is commonly associated with poor academic achievement and low occupational status, as well as increased risk of substance abuse and delinquency. The objective of this study was to evaluate adult ADHD subject reported outcomes when switched from a stable dose of CONCERTA(®) to the same dose of generic Novo-methylphenidate ER-C(®). Randomized, double-blind, cross-over, phase IV trial consisted of two phases in which participants with a primary diagnosis of ADHD were randomized in a 1:1 ratio to 3 weeks of treatment with CONCERTA or generic Novo-Methylphenidate ER-C. Following 3 weeks of treatment, participants were crossed-over to receive the other treatment for an additional 3 weeks. Primary efficacy was assessed through the use of the Treatment Satisfaction Questionnaire for Medication, Version II (TSQM-II). Participants with ADHD treated with CONCERTA were more satisfied in terms of efficacy and side effects compared to those receiving an equivalent dose of generic Novo-Methylphenidate ER-C. All participants chose to continue with CONCERTA treatment at the conclusion of the study. Although CONCERTA and generic Novo-Methylphenidate ER-C have been deemed bioequivalent, however the present findings demonstrate clinically and statistically significant differences between generic and branded CONCERTA. Further investigation of these differences is warranted.

  6. Experimental investigation on passive heat transfer by long closed two-phase thermosiphons

    Energy Technology Data Exchange (ETDEWEB)

    Grass, Claudia; Kulenovic, Rudi; Starflinger, Joerg [Stuttgart Univ. (Germany). Inst. fuer Kernenergetik und Energiesysteme (IKE)

    2017-07-15

    The removal of decay heat from spent fuel pools is presently realized by active cooling systems. In case of a station black out, a passive heat removal based on closed two-phase thermosiphons can contribute to the power plant safety. In this paper, the basic laboratory setup for closed two-phase thermosiphons and first experimental results are presented. Depending on the driving temperature difference and the heat input, steady-state and pulsating operation of the thermosiphons are investigated.

  7. Etravirine combined with antiretrovirals other than darunavir/ritonavir for HIV-1-infected, treatment-experienced adults: Week 48 results of a phase IV trial

    Directory of Open Access Journals (Sweden)

    Eduardo Arathoon

    2017-01-01

    Full Text Available Objective: VIOLIN (TMC125IFD3002; NCT01422330 evaluated the safety, tolerability, and pharmacokinetics of etravirine with antiretrovirals other than darunavir/ritonavir in HIV-1-infected patients. Methods: In a 48-week, phase IV, single-arm, multicenter study, patients on prior antiretroviral therapy (⩾8 weeks who needed to change regimen for virologic failure (viral load ⩾ 500 copies/mL or simplification/adverse events (viral load < 50 copies/mL received etravirine 200 mg bid with ⩾1 other active antiretroviral, excluding darunavir/ritonavir or only nucleoside/tide reverse transcriptase inhibitors. Results: Of 211 treated patients, 73% (n = 155 had baseline viral load ⩾ 50 copies/mL and 27% (n = 56 had baseline viral load < 50 copies/mL. Protease inhibitors were the most common background antiretrovirals (83%. Diarrhea was the most frequent adverse event (17%. Serious adverse events (no rash occurred in 5% of patients; none were etravirine related. Overall, median etravirine AUC12h was 5390 ng h/mL and C0h was 353 ng/mL (N = 199. Week 48 virologic response rates (viral load < 50 copies/mL; Food and Drug Administration Snapshot algorithm were 48% (74/155 (baseline viral load ⩾ 50 copies/mL and 75% (42/56 (baseline viral load < 50 copies/mL. Virologic failure rates were 42% and 13%, respectively. The most frequently emerging etravirine resistance-associated mutations in virologic failures were Y181C, E138A, and M230L. Virologic response rates for patients with baseline viral load ⩾ 50 copies/mL were 38% (30/79 (non-adherent versus 64% (44/69 (adherent subset. Conclusion: Etravirine 200 mg bid in combination with antiretrovirals other than darunavir/ritonavir was well tolerated in the studied treatment-experienced HIV-1-infected population. The overall etravirine safety and tolerability profile and pharmacokinetics (specifically in those patients who were adherent

  8. Efficacy and safety of cross-linked hyaluronic acid single injection on osteoarthritis of the knee: a post-marketing phase IV study

    Directory of Open Access Journals (Sweden)

    Bashaireh K

    2015-04-01

    Full Text Available Khaldoon Bashaireh,1 Ziad Naser,2 Khaled Al Hawadya,2 Sorour Sorour,2 Rami Nabeel Al-Khateeb3 1Department of Orthopedics Surgery, King Abdullah University Hospital, Jordan University of Science and Technology, Irbid, Jordan; 2Private Clinic, 3Elaf Medical Supplies Company, Amman, Jordan Purpose: The primary objective of this study was to evaluate the efficacy, safety, and duration of action of viscosupplementation with Crespine® Gel over a 9-month period.Materials and methods: The study was a post-marketing phase IV study. A total of 109 participants with osteoarthritis of the knee (grades 1–4 in the tibio–femoral compartment were recruited in Jordan. Data were collected from each participant during the baseline visit. Each participant received Crespine® Gel injection, and follow-up visits took place at 3 months, 6 months, and 9 months post-injection.Main outcome measure(s: An assessment of participants by phone was conducted at 1 month, 2 months, 4 months, 5 months, 7 months, and 8 months post-injection. Western Ontario and McMaster Universities Arthritis Index questionnaires were completed during each visit. A 72-hour visit questionnaire was used to assess the safety of the injection. Statistical analysis included a two-sided 95% confidence interval for the difference between pain scores across visits, and the percent change from baseline was calculated.Main results: The full analysis included 84 participants who gave their informed consent and finished the necessary baseline and follow-up visits needed to assess efficacy and safety. Peak improvement was noted at 5 months post-injection, when pain and physical performance scores had decreased to 2.60 and 9.90, respectively, and the stiffness score was 0.33. The peak improvement in stiffness was noted at 8 months post-injection, when the stiffness score had decreased to 0.32. Significant improvements were still apparent at 9 months post-injection, when the pain score was 3

  9. Efficacy and safety of cross-linked hyaluronic acid single injection on osteoarthritis of the knee: a post-marketing Phase IV study.

    Science.gov (United States)

    Bashaireh, Khaldoon; Naser, Ziad; Hawadya, Khaled Al; Sorour, Sorour; Al-Khateeb, Rami Nabeel

    2015-01-01

    The primary objective of this study was to evaluate the efficacy, safety, and duration of action of viscosupplementation with Crespine® Gel over a 9-month period. The study was a post-marketing Phase IV study. A total of 109 participants with osteoarthritis of the knee (grades 1-4) in the tibio-femoral compartment were recruited in Jordan. Data were collected from each participant during the baseline visit. Each participant received Crespine® Gel injection, and follow-up visits took place at 3 months, 6 months, and 9 months post-injection. An assessment of participants by phone was conducted at 1 month, 2 months, 4 months, 5 months, 7 months, and 8 months post-injection. Western Ontario and McMaster Universities Arthritis Index questionnaires were completed during each visit. A 72-hour visit questionnaire was used to assess the safety of the injection. Statistical analysis included a two-sided 95% confidence interval for the difference between pain scores across visits, and the percent change from baseline was calculated. The full analysis included 84 participants who gave their informed consent and finished the necessary baseline and follow-up visits needed to assess efficacy and safety. Peak improvement was noted at 5 months post-injection, when pain and physical performance scores had decreased to 2.60 and 9.90, respectively, and the stiffness score was 0.33. The peak improvement in stiffness was noted at 8 months post-injection, when the stiffness score had decreased to 0.32. Significant improvements were still apparent at 9 months post-injection, when the pain score was 3.36, the stiffness score was 0.42, and the physical performance score was 11.5. All side effects were local and transient, and included pain, swelling, and redness of the knee. Most side effects were treated. Hyaluronan should be encouraged as an alternative or adjunct treatment to oral analgesics to reduce their required doses, and delay potential future surgical intervention.

  10. Employment of a novel ultrasonic method to investigate high pressure phase transitions in oleic acid

    Science.gov (United States)

    Rostocki, A. J.; Siegoczyński, R. M.; Kiełczyński, P.; Szalewski, M.; Balcerzak, A.; Zduniak, M.

    2011-06-01

    In this work, the variation of sound velocity with hydrostatic pressure for oleic acid is evaluated up to 350 MPa. During the measurement, we identified the phase transformation of oleic acid and the presence of the hysteresis of the dependence of sound velocity on pressure. From the performed measurements, it can be seen that the dependence of sound velocity on pressure can be used to investigate phase transformations in natural oils. Ultrasonic waves were excited and detected using piezoelectric LiNbO3(Y-36 cut) 5 MHz transducers. The phase velocity of the longitudinal ultrasonic waves was measured using a cross-correlation method to evaluate the time of flight.

  11. Theoretical investigation of phase-controlled bias effect in capacitively coupled plasma discharges

    International Nuclear Information System (INIS)

    Kwon, Deuk-Chul; Yoon, Jung-Sik

    2011-01-01

    We theoretically investigated the effect of phase difference between powered electrodes in capacitively coupled plasma (CCP) discharges. Previous experimental result has shown that the plasma potential could be controlled by using a phase-shift controller in CCP discharges. In this work, based on the previously developed radio frequency sheath models, we developed a circuit model to self-consistently determine the bias voltage from the plasma parameters. Results show that the present theoretical model explains the experimental results quite well and there is an optimum value of the phase difference for which the V dc /V pp ratio becomes a minimum.

  12. Investigations of binary and ternary phase change alloys for future memory applications

    International Nuclear Information System (INIS)

    Rausch, Pascal

    2012-01-01

    The understanding of phase change materials is of great importance because it enables us to predict properties and tailor alloys which might be even better suitable to tackle challenges of future memory applications. Within this thesis two topics have been approached: on the one hand the understanding of the alloy In 3 Sb 1 Te 2 and on the other hand the so called resistivity drift of amorphous Ge-Sn-Te phase change materials. The main topic covers an in depth discussion of the ternary alloy In 3 Sb 1 Te 2 . At first glance, this alloy does not fit into the established concepts of phase alloys: e.g. the existence of resonant bonding in the crystalline phase is not obvious and the number of p-electrons is very low compared to other phase change alloys. Furthermore amorphous phase change alloys with high indium content are usually not discussed in literature, an exception being the recent work by Spreafico et al. on InGeTe 2 . For the first time a complete description of In 3 Sb 1 Te 2 alloy is given in this work for the crystalline phase, amorphous phase and crystallization process. In addition comparisons are drawn to typical phase change materials like Ge 2 Sb 2 Te 5 /GeTe or prototype systems like AgInTe 2 and InTe. The second topic of this thesis deals with the issue of resistivity drift, i.e. the increase of resistivity of amorphous phase change alloys with aging. This drift effect greatly hampers the introduction of multilevel phase change memory devices into the market. Recently a systematic decrease of drift coefficient with stoichiometry has been observed in our group going from GeTe over Ge 3 Sn 1 Te 4 to Ge 2 Sn 2 Te 4 . These alloys are investigated with respect to constraint theory.

  13. Separation of Th(IV) and U(VI) by extraction chromatography

    International Nuclear Information System (INIS)

    Nadkarni, M.N.; Mayankutty, P.C.; Pillai, N.S.

    1984-01-01

    Application of extraction chromatography to the analytical separation of Th(IV) and U(VI) has been investigated. The stationary phase was a macroporous resin Amberlite XE-270 impregnated with undiluted tri-n-butylphosphate (TBP) and the mobile phase was either 5.0M HNO 3 or 6M HCl. Separation of traces of Th(IV) from large quantities of U(VI) was achieved on a laboratory column by elution of the absorbed Th(IV) with 6M HCl. (author)

  14. Experimental investigation of phase equilibria in the Cu–Ni–Si ternary system

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Xingjun; Xiang, Shulin; Yang, Shuiyuan; Shi, Rongpei; Wang, Cuiping, E-mail: wangcp@xmu.edu.cn

    2013-11-25

    Highlights: •Three isothermal sections of the Cu–Ni–Si system have been investigated. •The ternary compound τ{sub 1} and the liquid phase are confirmed at 1073 K. •The γ (Cu{sub 5}Si) and θ (Ni{sub 2}Si) phases can be stabilized at higher or lower temperatures. -- Abstract: The phase equilibria in the Cu–Ni–Si ternary system have been investigated experimentally by means of electron probe microanalysis (EPMA), X-ray diffraction (XRD) and differential scanning calorimetry (DSC) analysis on equilibrated ternary alloys. Three isothermal sections at 1073, 1173 and 1273 K are determined in the whole composition range. The existence of liquid phase and the ternary compound τ{sub 1} is confirmed at 1073 K. The binary γ (Cu{sub 5}Si), γ (Ni{sub 31}Si{sub 12}), δ (Ni{sub 2}Si) and θ (Ni{sub 2}Si) phases exhibit a considerable solubility of a third element. In addition, the γ (Cu{sub 5}Si) and θ (Ni{sub 2}Si) phases can be stabilized by the addition of Ni and Cu, respectively.

  15. Aespoe Hard Rock Laboratory - feasibility and usefulness of site investigation methods. Experiences from the pre-investigation phase

    Energy Technology Data Exchange (ETDEWEB)

    Almen, K E [ed.; KEA GEO-Konsult (Sweden); Olsson, Paer [SKANSKA, (Sweden); Rhen, I [VBB VIAK AB, Malmoe (Sweden); Stanfors, R [RS Consulting, (Sweden); Wikberg, P [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden)

    1994-08-01

    One of the main goals set up by SKB for the Aespoe HRL project is to `test the quality and appropriateness of different methods for characterizing the bedrock with respect to conditions of importance for a final repository`. An extensive investigation programme was carried out during the projects pre-investigation phase that in part was based in experience from SKBs previous site investigations and in part entailed the testing of new or other unestablished methods. Previous technical reports have described the methods that have been used and the results, models and predictions that have been produced. All the methods used are discussed in the present report in terms of how they have contributed in different analysis stages to the total geoscientific characterization of the rock at Aespoe. The usefulness of each method for modelling and prediction in different scales is evaluated, and aspects of the practical execution of the methods under different conditions are discussed. The report sheds light on the importance of dividing large investigation programmes such as this one into suitable stages to get an opportunity to evaluate the results obtained and plan in detail the investigations in the next stage. Furthermore, the way in which the characterization/modelling work in different geometric scales has been done for the different investigation stages is discussed, along with whether this has been found to be a suitable approach. The importance of pursuing an interdisciplinary strategy throughout the pre-investigation process cannot be overemphasized. For the planning, execution, analysis and reporting of the results of the pre-investigations, this has been guaranteed by an organization in which an interdisciplinary group has been in charge of the investigations, together with the project manager. 52 refs, numerous tabs and figs.

  16. In-situ investigation of the icosahedral Al-Cu-Fe phase formation in thin films

    Energy Technology Data Exchange (ETDEWEB)

    Haidara, F., E-mail: fanta.haidara@im2np.fr [IM2NP, UMR 6242 CNRS - Universite Aix-Marseille, Av. Escadrille Normandie-Niemen, Case 142, 13397 Marseille Cedex 20 (France); Duployer, B. [Universite Paul Sabatier CIRIMAT-LCMIE 2R1, 118, Route de Narbonne, 31062 Toulouse Cedex 09 (France); Mangelinck, D.; Record, M.-C. [IM2NP, UMR 6242 CNRS - Universite Aix-Marseille, Av. Escadrille Normandie-Niemen, Case 142, 13397 Marseille Cedex 20 (France)

    2012-09-05

    Highlights: Black-Right-Pointing-Pointer We investigated the phase formation of i-Al{sub 62.5}Cu{sub 25}Fe{sub 12.5} in thin films. Black-Right-Pointing-Pointer We characterized the samples by DSC and in-situ XRD and resistance measurements. Black-Right-Pointing-Pointer The resistivity value for i-Al{sub 62.5}Cu{sub 25}Fe{sub 12.5} was determined. - Abstract: This work is an investigation of the formation by reactive diffusion at high temperatures of the icosahedral phase, i-Al{sub 62.5}Cu{sub 25}Fe{sub 12.5}, in thin films. The samples were prepared by sputtering at room temperature. The elements Al, Cu and Fe were sequentially deposited onto oxidized silicon substrates. The two following stacking sequences, Al/Cu/Fe and Al/Fe/Cu, were investigated. The phase formation was studied using in situ resistivity, in situ X-ray Diffraction and Differential Scanning Calorimetry measurements. Whatever the stacking sequence, the sequences of phase formation evidenced during the heating treatment are similar. However the temperatures of formation for the first phases that are formed are different; they are higher in the case of the Al/Fe/Cu stacking sequence.

  17. Phase study in Sr-Th-P-O system: Structural and thermal investigations of quaternary compounds

    International Nuclear Information System (INIS)

    Keskar, Meera; Phatak, Rohan; Sali, S.K.; Krishnan, K.; Dahale, N.D.; Kulkarni, N.K.; Kannan, S.

    2011-01-01

    The sub-solidus phase relations in Sr-Th-P-O quaternary system were determined at 1223 K in air. To confirm the formation and stability of reported phases, ternary and quaternary compounds in Sr-Th-O, Sr-P-O, Th-P-O and Sr-Th-P-O systems were synthesized by solid state reactions of SrCO 3 , ThO 2 and NH 4 H 2 PO 4 in desired molar proportions at 1223 K. A pseudo-ternary phase diagram of SrO-ThO 2 -P 2 O 5 system was drawn on the basis of the phase analysis of various phase mixtures and phase fields were established by powder X-ray diffraction. In the phase diagram, three quaternary compounds SrTh(PO 4 ) 2 , SrTh 4 (PO 4 ) 6 and Sr 7 Th(PO 4 ) 6 were identified. When heated in air at 1673 K, these compounds decompose to ThO 2 . Structures of SrTh(PO 4 ) 2 , SrTh 4 (PO 4 ) 6 and Sr 7 Th(PO 4 ) 6 were derived from X-ray powder data using the Rietveld refinement method. Thermal expansion behaviors of SrTh(PO 4 ) 2 , SrTh 4 (PO 4 ) 6 and Sr 7 Th(PO 4 ) 6 were investigated using high-temperature X-ray diffraction in the temperature range of 298-1273 K.

  18. Structure and phase behaviour of diblock copolymer monolayers investigated by means of Monte Carlo simulation

    International Nuclear Information System (INIS)

    Słyk, Edyta; Rżysko, Wojciech; Bryk, Paweł

    2015-01-01

    We use grand canonical Monte Carlo simulation paired with multiple histogram reweighting, hyperparallel tempering and finite size scaling to investigate the structure and phase behaviour of monolayers of diblock copolymers. The chain molecules are arranged on the square lattice and we consider both fully flexible and rod-coil polymer models. In contrast to the majority of previous studies we assume that the interactions between the segments belonging to one of the two subunits are weaker than the remaining segment–segment interactions. We find that when the diblock copolymer is fully flexible, this choice of the interactions leads to a suppression of the ordered phase, and the phase behaviour is analogous to that of the fully flexible homopolymer model. However, when one of the subunits is rigid, we observe the formation of a novel hairpin chessboard ordered structure with fully stretched chains bent in the middle. The topology of the phase diagram depends on the chain length. For shorter chains the global phase diagram features a critical point and a triple point. For longer chains the gas—disordered liquid phase transition is suppressed and only the order–disorder transition remains stable. The resulting phase diagram is of the swan neck type. (paper)

  19. Phase transitions of amorphous solid acetone in confined geometry investigated by reflection absorption infrared spectroscopy.

    Science.gov (United States)

    Shin, Sunghwan; Kang, Hani; Kim, Jun Soo; Kang, Heon

    2014-11-26

    We investigated the phase transformations of amorphous solid acetone under confined geometry by preparing acetone films trapped in amorphous solid water (ASW) or CCl4. Reflection absorption infrared spectroscopy (RAIRS) and temperature-programmed desorption (TPD) were used to monitor the phase changes of the acetone sample with increasing temperature. An acetone film trapped in ASW shows an abrupt change in the RAIRS features of the acetone vibrational bands during heating from 80 to 100 K, which indicates the transformation of amorphous solid acetone to a molecularly aligned crystalline phase. Further heating of the sample to 140 K produces an isotropic solid phase, and eventually a fluid phase near 157 K, at which the acetone sample is probably trapped in a pressurized, superheated condition inside the ASW matrix. Inside a CCl4 matrix, amorphous solid acetone crystallizes into a different, isotropic structure at ca. 90 K. We propose that the molecularly aligned crystalline phase formed in ASW is created by heterogeneous nucleation at the acetone-water interface, with resultant crystal growth, whereas the isotropic crystalline phase in CCl4 is formed by homogeneous crystal growth starting from the bulk region of the acetone sample.

  20. Differential thermal, Thermogravimetric and X-ray diffraction investigation of hydration phases in cementitious waste form

    International Nuclear Information System (INIS)

    Khalil, M.Y.; Nagy, M.E.; El-Sourougy, M.R.; Zaki, A.A.

    1996-01-01

    Hydration phases of cement determine the final properties of the product. Adding other components to the cement paste may alter the final phases formed and affect properties of the hardened products. In this work ordinary portland cement and/or blast furnace slag cement were hardened with low-or intermediate-level radioactive liquid wastes and different additives. Hydration phases were investigated using differential thermal, thermogravimetric, and X-ray diffraction techniques. Low-and intermediate-level liquid wastes were found not to affect the hydration phases of cement. The addition of inorganic exchangers and latex were found to affect the hydration properties of the cement waste system. This resulted in a reduction of compressive strength. On the contrary, addition of epoxy also affected the hydration causing increase in compressive strength. 10 figs., 2 tabs

  1. Experimental investigation of phase equilibria in the Ni-Nb-V ternary system

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Xingjun; Yang, Shuiyuan; Wang, Cuiping [Xiamen Univ. (China). Dept. of Materials Science and Engineering; Xiamen Univ. (China). Fujian Provincial Key Lab. of Materials Genome; Zhang, Xianjie; Jiang, Hengxing; Shi, Zhan [Xiamen Univ. (China). Dept. of Materials Science and Engineering

    2017-09-15

    The phase equilibria of the Ni-Nb-V ternary system at 1000 C and 1200 C were established using electron probe microanalysis, X-ray diffraction and differential scanning calorimetry. The results of the investigation revealed that: (1) The Nb solubility in (Ni) and σ{sup '} phases was less than 10 at.%; (2) A ternary compound τ (NiNbV) was confirmed, in which V had a large solubility; (3) A new liquid region was evident at 1200 C, but was absent at 1000 C; (4) The lattice constants of Ni{sub 3}Nb and Ni{sub 6}Nb{sub 7} phase decreased with increase in V content in the Ni{sub 3}Nb and Ni{sub 6}Nb{sub 7}. The phase equilibria of the Ni-Nb-V ternary system will contribute to its thermodynamic assessment.

  2. Investigation on phase noise of the signal from a singly resonant optical parametric oscillator

    Science.gov (United States)

    Jinxia, Feng; Yuanji, Li; Kuanshou, Zhang

    2018-04-01

    The phase noise of the signal from a singly resonant optical parametric oscillator (SRO) is investigated theoretically and experimentally. An SRO based on periodically poled lithium niobate is built up that generates the signal with a maximum power of 5.2 W at 1.5 µm. The intensity noise of the signal reaches the shot noise level for frequencies above 5 MHz. The phase noise of the signal oscillates depending on the analysis frequency, and there are phase noise peaks above the shot noise level at the peak frequencies. To explain the phase noise feature of the signal, a semi-classical theoretical model of SROs including the guided acoustic wave Brillouin scattering effect within the nonlinear crystal is developed. The theoretical predictions are in good agreement with the experimental results.

  3. Three-Dimensional Radiation Therapy to the Primary Tumor With Concurrent Chemotherapy in Patients With Stage IV Non-Small Cell Lung Cancer: Results of a Multicenter Phase 2 Study From PPRA-RTOG, China

    Energy Technology Data Exchange (ETDEWEB)

    Su, ShengFa [Department of Thoracic Oncology, Affiliated Hospital of Guizhou Medical University, and Guizhou Cancer Hospital, Guiyang (China); Teaching and Research Section of Oncology, Guizhou Medical University, Guiyang (China); Li, Tao [Department of Radiation Oncology, Sichuan Cancer Hospital, Chengdu (China); Lu, Bing, E-mail: lbgymaaaa@163.com [Department of Thoracic Oncology, Affiliated Hospital of Guizhou Medical University, and Guizhou Cancer Hospital, Guiyang (China); Teaching and Research Section of Oncology, Guizhou Medical University, Guiyang (China); Wang, XiaoHu, E-mail: xhwanggansu@163.com [Department of Radiation Oncology, Gansu Cancer Hospital, Lanzhou (China); Li, JianCheng [Department of Radiation Oncology, Fujian Provincial Cancer Hospital, Fuzhou (China); Chen, Ming [Department of Radiation Oncology, Zhejiang Cancer Hospital, Hangzhou (China); Lu, You [Department of Thoracic Oncology and State Key Laboratory of Biotherapy, Cancer Center, West China Hospital, Sichuan University, Chengdu (China); Bai, YuJu [Department of Oncology, Affiliated Hospital of Zunyi Medical College, Zunyi (China); Hu, YinXiang; Ouyang, WeiWei; Ma, Zhu; Li, QingSong; Li, HuiQin; Wang, Yu [Department of Thoracic Oncology, Affiliated Hospital of Guizhou Medical University, and Guizhou Cancer Hospital, Guiyang (China); Teaching and Research Section of Oncology, Guizhou Medical University, Guiyang (China)

    2015-11-15

    Purpose: The aim of this prospective multi-institutional phase 2 study was to investigate disease control, survival outcomes, and toxicity after thoracic three-dimensional radiation therapy (3D-RT) with concurrent chemotherapy for newly diagnosed stage IV non-small cell lung cancer (NSCLC). Methods and Materials: Eligible patients were 18 to 80 years of age, had a Karnofsky performance status (KPS) score ≥70%, and newly diagnosed stage IV NSCLC with limited metastatic disease (defined as involving ≤3 organs). Patients received platinum-doublet chemotherapy with concurrent irradiation to the primary tumor. Primary endpoints were overall survival (OS) and acute toxicity. Results: From May 2008 to May 2012, 198 eligible patients were enrolled from 7 cancer centers. Most patients died with distant metastasis; only 10% died with isolated primary recurrence. Median OS time was 13.0 months (95% confidence interval [CI]: 11.7-14.3); OS rates were 53.5% at 1 year, 15.8% at 2 years, and 9.2% at 3 years. Median progression-free survival (PFS) time was 9.0 months (95% CI: 7.7-10.3); corresponding PFS rates were 30.8%, 8.2%, and 6.1%. The 1-year, 2-year, and 3-year local (primary tumor) control rates were 78.8%, 57.7%, and 55.4%. Multivariate analysis showed that delivery of ≥63 Gy to the primary tumor (P=.014), having a primary tumor volume <134 cm{sup 3} (P=.008), and having a stable or higher KPS score after treatment (P=.01) were independent predictors of better OS. The most common severe (grades 3-4) acute toxicities were hematologic: leukopenia (37.9%), thrombocytopenia (10.1%), and anemia (6.9%). No patients experienced grade 4 or 5 radiation-related toxicity; 2.5% had acute grade 3 pneumonitis, and 6.6% had acute grade 3 radiation esophagitis. Conclusions: Thoracic 3D-RT to the primary tumor with concurrent chemotherapy led to satisfactory survival outcomes with acceptable toxicity. Radiation dose, primary tumor volume, and PFS after treatment all

  4. Safety and efficacy of paliperidone palmitate 1-month formulation in Chinese patients with schizophrenia: a 25-week, open-label, multicenter, Phase IV study

    Directory of Open Access Journals (Sweden)

    Zhao JP

    2017-08-01

    Full Text Available Jingping Zhao,1,* Lehua Li,1,* Jianguo Shi,2 Yi Li,3 Xiufeng Xu,4 Keqing Li,5 Lili Zhang,6 Shangli Cai,6 Yu Feng,6 Jianmin Zhuo,6 Weihong Liu,6 Huafei Lu6 1Department of Psychiatry, The Mental Health Institute, The Second Xiangya Hospital of Central South University, 2Department of Psychiatry, Mental Health Center of Xi’an City, 3Department of Psychiatry, Mental Health Center of Wuhan City, 4Department of Psychiatry, First Affiliated Hospital of Kunming Medical University, 5Department of Psychiatry, The Sixth People’s Hospital of Hebei Province, 6Department of Medical Affairs, Xi’an Janssen Pharmaceutical Ltd., Beijing, People’s Republic of China *These authors contributed equally to this work Rationale: Long-acting injectable (LAI paliperidone palmitate 1-month formulation (PP1M has demonstrated acceptable tolerability and favorable clinical outcomes in Western and Asian patients with schizophrenia. Hence, analysis of the outcomes of long-term PP1M treatment specifically in Chinese patients is of interest.Objective: The aim of this study is to evaluate the long-term safety and efficacy of PP1M treatment in Chinese patients with schizophrenia.Methods: In this 25-week, open-label, Phase IV study, patients (18–65 years diagnosed with schizophrenia and having a baseline Positive and Negative Syndrome Scale (PANSS total score of 60–120 (inclusive were enrolled. All patients received injections of PP1M 150 mg eq. (day 1 and 100 mg eq. (day 8, followed by a flexible once-monthly maintenance dosing (75, 100, or 150 mg eq..Results: Of the 353 patients, 234 (66.3% completed the study treatment (mean age, 31.1 years; 52.7% men. The PANSS total score (primary end point improved significantly over the 6-month treatment period (mean [standard deviation] change from baseline to end of treatment, -27.2 [18.30]; P<0.0001. The Clinical Global Impressions-Severity and Personal and Social Performance scores (secondary end points also improved

  5. Quality and clinical supply considerations of Paediatric Investigation Plans for IV preparations-A case study with the FP7 CloSed project.

    Science.gov (United States)

    Hanning, Sara M; Orlu Gul, Mine; Winslade, Jackie; Baarslag, Manuel A; Neubert, Antje; Tuleu, Catherine

    2016-09-25

    A Paediatric Investigation Plan (PIP) is a development plan that aims to ensure that sufficient data are obtained through studies in paediatrics to support the generation of marketing authorisation of medicines for children. This paper highlights some practical considerations and challenges with respect to PIP submissions and paediatric clinical trials during the pharmaceutical development phase, using the FP7-funded Clonidine for Sedation of Paediatric Patients in the Intensive Care Unit (CloSed) project as a case study. Examples discussed include challenges and considerations regarding formulation development, blinding and randomisation, product labelling and shipment and clinical trial requirements versus requirements for marketing authorisation. A significant quantity of information is required for PIP submissions and it is hoped that future applicants may benefit from an insight into some critical considerations and challenges faced in the CloSed project. Copyright © 2016 Elsevier B.V. All rights reserved.

  6. Diorganotin(IV) Complexes with Methionine Methyl Ester. Equilibria ...

    African Journals Online (AJOL)

    IV) (DBT) and diphenyltin(IV) (DPT) was investigated at 25 °C and 0.1 mol dm–3 ionic strength in water for dimethyltin(IV) and in 50 % dioxane–water mixture for dibutyltin(IV) and diphenyltin(IV). Methionine methyl ester forms1:1 and 1:2 ...

  7. Neutron powder investigation of the tetragonal to monoclinic phase transformation in undoped zirconia

    International Nuclear Information System (INIS)

    Boysen, H.; Frey, F.

    1991-01-01

    The tetragonal (t) to monoclinic (m) transformation in pure ZrO 2 was investigated by neutron powder diffraction at temperatures between 1900 K and room temperature. The results of a Rietveld analysis are compared with a previous investigation of the m → t transformation. The t → m transformation takes place near 1200 K (implaying a hysteresis of 300 K) and in a much smaller interval (about 150 K compared with about 600 K in the m → t case). There are no indications of a two-stage process as found for the m → t transformation. The structural parameters of the m phase depend only on temperature while those of the t phase differ at the same temperatures for the forward and reverse transformation. The temperature dependence of the lattice constants suggests an orientational relationship a t parallela m * and c t parallelb m . There are no macrostrains whereas the overall microstrain behaviour is similar in both cases, viz. the large microstrains present in both phases are released within the transformation regime. An analysis of temperature factors and diffuse background suggest dynamical disorder in the t phase and static disorder in the m phase. (orig.)

  8. A Taxometric Investigation of "DSM-IV" Major Depression in a Large Outpatient Sample: Interpretable Structural Results Depend on the Mode of Assessment

    Science.gov (United States)

    Ruscio, John; Brown, Timothy A.; Ruscio, Ayelet Meron

    2009-01-01

    Most taxometric studies of depressive constructs have drawn indicators from self-report instruments that do not bear directly on the "Diagnostic and Statistical Manual of Mental Disorders, 4th edition (DSM-IV)" diagnostic construct of major depressive disorder (MDD). The present study examined the latent structure of MDD using indicator sets…

  9. Horonobe Underground Research Laboratory Project. Plans for surface-based investigations. Phase 1

    International Nuclear Information System (INIS)

    Goto, Junichi; Hama, Katsuhiro

    2003-10-01

    The Horonobe Underground Research Laboratory Project is an investigation project which is planned over 20 years. The investigations are conducted in the three phases: investigations from surface (Phase 1), investigations during construction of the underground facility (Phase 2) and investigations using the facility (Phase 3). Taking into account the results from 'H12: Project of Establish the Scientific and Technical Basis for HLW Disposal in Japan - Second Progress Report on Research and Development for the Geological Disposal of HLW in Japan-' (JNC, 2000), research and development goals for the Horonobe URL project were re-defined as follows; a) Development of investigation technologies for the geological environment, b) Development of monitoring technologies for the geological environment, c) Study on the long-term stability of the geological environment, d) Development of the basis for engineering technologies in deep underground, e) Verification of technologies for engineered barriers, f) Development of detailed designing technologies of the repositories, and g) Improvement of safety assessment methodologies. Investigations for the goals a) to d) and e) to g) are conducted in the 'Geoscientific Research' and 'Research and Development on Geological Disposal', respectively. In Phase 1, a 'laboratory construction area' of a few kilometers square is selected based on the results from early stage investigations. Subsequent investigations are concentrated in the selected area and its periphery. Acquisition of data by surface-based investigations, modeling of the geological environment and predictions of changes in the geological environment caused by the construction of the underground facility, are conducted in a) Development of investigation technologies for the geological environment. Development and installation of monitoring equipments and data acquisition prior to the construction of the underground facility fall under b) Development of monitoring technologies

  10. Experimental investigation of phase equilibria in the Co-Ni-Zr ternary system

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Xingjun; Yang, Shuiyuan; Yu, Wenjie; Wang, Cuiping [Xiamen Univ. (China). Fujian Key Laboratory of Materials Genome; Xiong, Huaping; Cheng, Yaoyong; Wu, Xin [Beijing Institute of Aeronautical Materials (China). Div. of Welding and Forging

    2016-10-15

    The phase equilibria of the Co-Ni-Zr ternary system at 1 000 C, 1 100 C and 1 200 C were experimentally investigated by means of back-scattered electron imaging, electron probe microanalysis and X-ray diffraction on the equilibrated ternary alloys. In this study, no ternary compound is found. The (αCo, Ni) phase region extends from the Ni-rich corner to the Co-rich corner with small solubility of Zr at three sections. At 1 000 C and 1 100 C, Ni{sub 5}Zr, Co{sub 2}Zr and Ni{sub 10}Zr{sub 7} phases have large solid solution ranges, but Ni{sub 10}Zr{sub 7} phase disappears at 1 200 C. The Ni{sub 7}Zr{sub 2}, NiZr, Co{sub 11}Zr{sub 2}, Co{sub 23}Zr{sub 6} and CoZr phases exhibit nearly linear compounds in the studied sections, and have large composition ranges. Additionally, some differences in phase relationship exist among the above three isothermal sections.

  11. Investigations of effect of phase change mass transfer rate on cavitation process with homogeneous relaxation model

    Energy Technology Data Exchange (ETDEWEB)

    He, Zhixia; Zhang, Liang; Saha, Kaushik; Som, Sibendu; Duan, Lian; Wang, Qian

    2017-12-01

    The super high fuel injection pressure and micro size of nozzle orifice has been an important development trend for the fuel injection system. Accordingly, cavitation transient process, fuel compressibility, amount of noncondensable gas in the fuel and cavitation erosion have attracted more attention. Based on the fact of cavitation in itself is a kind of thermodynamic phase change process, this paper takes the perspective of the cavitation phase change mass transfer process to analyze above mentioned phenomenon. The two-phase cavitating turbulent flow simulations with VOF approach coupled with HRM cavitation model and U-RANS of standard k-ε turbulence model were performed for investigations of cavitation phase change mass transfer process. It is concluded the mass transfer time scale coefficient in the Homogenous Relaxation Model (HRM) representing mass transfer rate should tend to be as small as possible in a condition that ensured the solver stable. At very fast mass transfer rate, the phase change occurs at very thin interface between liquid and vapor phase and condensation occurs more focused and then will contribute predictably to a more serious cavitation erosion. Both the initial non-condensable gas in fuel and the fuel compressibility can accelerate the cavitation mass transfer process.

  12. Experimental investigation and thermodynamic calculations of the Bi–In–Ni phase diagram

    International Nuclear Information System (INIS)

    Premović, Milena; Minić, Duško; Manasijević, Dragan; Ćosović, Vladan; Živković, Dragana; Dervišević, Irma

    2015-01-01

    Highlights: • Calculated constitutive binary system based on literature data. • Experimentally determined (DTA) temperatures of phase transformations compared with analytical calculation. • Definition of several vertical sections. • Calculated horizontal section, confirmed by experimental SEM–EDS and XRD method. • Calculated liquidus surface projection and determined invariant reaction occurred in ternary Bi–In–Ni system. - Abstract: Phase diagram of the Bi–In–Ni ternary system was investigated using differential thermal analysis (DTA), scanning electron microscopy (SEM) with energy dispersive spectrometry (EDS), and X-ray powder diffraction (XRD) analysis. Experimentally obtained results were compared with the results of thermodynamic calculation of phase equilibria based on calculation of phase diagram (CALPHAD) method and literature data. Phase transition temperatures of alloys with overall compositions along three selected vertical sections In–Bi 0.8 Ni 0.2 , x(Bi) = 0.6 and Bi–In 0.5 Ni 0.5 were measured by DTA. Liquidus temperatures were experimentally determined and compared with the results of thermodynamic calculation. Identification of coexisting phases in samples equilibrated at 100 °C, 300 °C and 350 °C was carried out using SEM–EDS and XRD methods. The obtained results were compared with the calculated isothermal sections of the Bi–In–Ni ternary system at corresponding temperatures. Calculated liquidus projection and invariant equilibria of the Bi–In–Ni ternary system were presented

  13. Investigation on the phase transformation of Bi-2223/Ag superconducting tapes during heating

    International Nuclear Information System (INIS)

    Huang, K.-T.; Qu, T.-M.; Xie, P.; Han, Z.

    2013-01-01

    Highlights: • In situ resistance measurement was carried out on Bi-2223/Ag superconducting tapes. • The oxygen partial pressure of the outlet gas in the heating process was monitored continuously. • The samples quenched in the heating process were studied by XRD and T c measurements. • The heating process contains three procedures: oxygen diffusion, Pb-rich phase evolution and liquid phase formation. -- Abstract: The phase transformation of Bi-2223/Ag superconducting tapes during heating was investigated. The resistance of the ceramic core as a function of the heating temperature was measured in situ. The pO 2 of the outlet gas in the heating process was also monitored continuously. By comparing the heating process with the X-ray diffraction and T c measurements taken from samples quenched at different temperatures, we have identified that the heating process could be divided into the following regions: (1) the oxygen diffusion (OD) region, which is mainly influenced by OD; (2) the Pb-rich phase evolution (PbE) region, in which the formation and decomposition of the Pb-rich phases occur; (3) the liquid phase formation (LF) region, in which resistance increased rapidly with increasing temperature

  14. Experimental investigation and thermodynamic calculations of the Ag–Bi–Ga phase diagram

    International Nuclear Information System (INIS)

    Minić, Duško; Premović, Milena; Manasijević, Dragan; Ćosović, Vladan; Živković, Dragana; Marković, Aleksandar

    2015-01-01

    Phase diagram of the Ag–Bi–Ga ternary system was investigated using differential thermal analysis (DTA), scanning electron microscopy (SEM) with energy dispersive spectrometry (EDS), and x-ray powder diffraction (XRD) methods. Experimentally obtained results were compared with the results of thermodynamic prediction of phase equilibria based on calculation of phase diagram (CALPHAD) method. Phase transition temperatures of alloys with overall compositions along three selected vertical sections Ag–Bi 50 Ga 50 , Bi–Ag 50 Ga 50 and Ga–Ag 50 Bi 50 were measured by DTA. Liquidus temperatures were experimentally determined and compared with the results of thermodynamic calculation. Identification of coexisting phases in samples equilibrated at 200 °C was carried out using SEM-EDS and XRD methods. Obtained results were compared with the calculated isothermal section of the Ag–Bi–Ga ternary system at corresponding temperature. Calculated liquidus projection and invariant equilibria of the Ag–Bi–Ga ternary system were presented. The obtained values were found to be in a close agreement. - Highlights: • Calculated constitutive binary system based on literature data. • Experimentally determined (DTA) temperatures of phase transformations compared with analytical calculation. • Definition of three vertical sections Ag–Bi 50 Ga 50 , Bi–Ag 50 Ga 50 and Ga–Ag 50 Bi 50 . • Calculated horizontal section at 200 °C, confirmed by experimental SEM-EDS and XRD method. • Calculated liquidus surface projection and determined invariant reaction occurred in ternary Ag–Bi–Ga system

  15. Preliminary applications of the new Neptune two-phase CFD solver to pressurized thermal shock investigations

    International Nuclear Information System (INIS)

    Boucker, M.; Laviaville, J.; Martin, A.; Bechaud, C.; Bestion, D.; Coste, P.

    2004-01-01

    The objective of this communication is to present some preliminary applications to pressurized thermal shock (PTS) investigations of the CFD (Computational Fluid Dynamics) two-phase flow solver of the new NEPTUNE thermal-hydraulics platform. In the framework of plant life extension, the Reactor Pressure Vessel (RPV) integrity is a major concern, and an important part of RPV integrity assessment is related to PTS analysis. In the case where the cold legs are partially filled with steam, it becomes a two-phase problem and new important effects occur, such as condensation due to the Emergency Core Cooling (ECC) injections of sub-cooled water. Thus, an advanced prediction of RPV thermal loading during these transients requires sophisticated two-phase, local scale, 3-dimensional codes. In that purpose, a program has been set up to extend the capabilities of the NEPTUNE two-phase CFD solver. A simple set of turbulence and condensation model for free surface steam-water flow has been tested in simulation of an ECC high pressure injection representing facility, using a full 3-dimensional mesh and the new NEPTUNE solver. Encouraging results have been obtained but it should be noticed that several sources of error can compensate for one another. Nevertheless, the computation presented here allows to be reasonable confident in the use of two-phase CFD in order to carry out refined analysis of two-phase PTS scenarios within the next years

  16. Investigation of phase transformation for ferrite–austenite structure in stainless steel thin films

    Energy Technology Data Exchange (ETDEWEB)

    Merakeb, Noureddine [Laboratory of Physical Metallurgy and Property of Materials (LM2PM), Metallurgy and Materials Engineering Department, Badji Mokhtar University, P.O. Box 12, Annaba 23000 (Algeria); Messai, Amel [Laboratoire d' Ingénierie et Sciences des Matériaux Avancés (ISMA), Institut des Sciences et Technologie, Abbès Laghrour University, Khenchela 40000 (Algeria); Ayesh, Ahmad I., E-mail: ayesh@qu.edu.qa [Department of Mathematics, Statistics and Physics, Qatar University, Doha (Qatar)

    2016-05-01

    In this work we report on phase transformation of 304 stainless steel thin films due to heat treatment. Ex-situ annealing was applied for evaporated 304 stainless steel thin films inside an ultra-high vacuum chamber with a pressure of 3 × 10{sup −7} Pa at temperatures of 500 °C and 600 °C. The structure of thin films was studied by X-ray diffraction (XRD) and conversion electron Mössbauer spectroscopy (CEMS) techniques. The results revealed a transformation from α-phase that exhibits a body-centered cubic structure (BCC) to γ-phase that exhibits a face-centered cubic (FCC) due to annealing. In addition, the percentage of γ-phase structure increased with the increase of annealing temperature. Annealing thin films increased the crystal size of both phases (α and γ), however, the increase was nonlinear. The results also showed that phase transformation was produced by recrystallization of α and γ crystals with a temporal evolution at each annealing temperature. The texture degree of thin films was investigated by XRD rocking curve method, while residual stress was evaluated using curvature method. - Highlights: • Stainless steel thin films were fabricated by thermal evaporation on quartz. • Alpha to gamma phase transformation of thin films was investigated. • Annealing of thin films reduces disruption in crystal lattice. • The stress of as-grown thin films was independent on the thin film thickness. • The stress of the thin films was reduced due to annealing.

  17. New methods for the investigation of phase objects by digital Speckle-pattern-interferometry

    International Nuclear Information System (INIS)

    Fliesser, W.

    1996-11-01

    This work shows new possibilities for spatially resolved interferometric investigations of transparent objects (phase-objects) applying the method of Digital-Speckle-Pattern-Interferometry (DSPI). A feedback-system using an additional MICHELSON-interferometer in the reference-arm of the Speckle-interferometer was installed for computer-controlled digitalization of the primary interferograms at defined phase-shifts. A special program for interferogram analysis allows the evaluation of two-dimensional phase distributions using different phase-stepping algorithms as 3-Frame-, 4-Frame-, CARRE-, 4+1-Frame- and 6+1-Frame technique. Special DSPI-setups with modified MACH-ZEHNDER-interferometers were used to check the system. In some basic experiments the temperature distribution in a cross section of convective heat-flows of air was measured. As an application on plasma-diagnostics the space-resolved electron density in a high pressure mercury lamp was determined using two-wavelength-DSPI. To increase the sensitivity of the method a Nd-YAG-laser at 1064 nm was employed in addition to an Ar + -laser at 488 Nm. The electron density in one cross-section of the lamp could be calculated by ABEL-inversion of the measured phase data. A multi-directional optical setup with a special mirror system was developed to investigate asymmetric phase-objects by DSPI. The setup allows to store six primary interferograms from different directions in one step, while using a single reference-beam only. Helium flows in air with different flow geometries were used as phase-objects. Tomographic reconstruction procedures such as the convolution-method yield the distributions of the refractive-index and the related helium concentrations in selected cross sections of the flow. (author)

  18. Theoretical analysis of nuclear reactors (Phase II), I-V, Part III, Reactor poisoning; Razrada metoda teorijske analize nuklearnih reaktora (II faza) I-V, III Deo, Zatrovanje reaktora, II faza

    Energy Technology Data Exchange (ETDEWEB)

    Pop-Jordanov, J [Institute of Nuclear Sciences Boris Kidric, Vinca, Beograd (Serbia and Montenegro)

    1962-10-15

    This phase is dealing with influence of all the fission products except Xe{sup 135} on the reactivity of a reactor, usually named as reactor poisoning. The first part of the report is a review of methods for calculation of reactor poisoning. The second part shows the most frequently used method for calculation of cross sections and yields of pseudo products (for thermal neutrons). The system of equations was adopted dependent on the conditions of the available computer system. It is described in part three. Detailed method for their application is described in part four and results obtained are presented in part five.

  19. Electrochemical investigations of Pu(IV)/Pu(III) redox reaction using graphene modified glassy carbon electrodes and a comparison to the performance of SWCNTs modified glassy carbon electrodes

    International Nuclear Information System (INIS)

    Gupta, Ruma; Gamare, Jayashree; Sharma, Manoj K.; Kamat, J.V.

    2016-01-01

    Highlights: • First report of aqueous electrochemistry of Plutonium on graphene modified electrode. • Graphene is best electrocatalytic material for Pu(IV)/Pu(III) redox couple among the reported modifiers viz. reduced graphene oxide (rGO) and SWCNT’s. • The electrochemical reversibility of Pu(IV)/Pu(III) redox couple improves significantly on graphene modified electrode compared to previously reported rGO & SWCNTs modified electrodes • Donnan interaction between plutonium species and graphene surface offers a possibility for designing a highly sensitive sensor for plutonium • Graphene modified electrode shows higher sensitivity for the determination of plutonium compared to glassy carbon and single walled carbon nanotube modified electrode - Abstract: The work reported in this paper demonstrates for the first time that graphene modified glassy carbon electrode (Gr/GC) show remarkable electrocatalysis towards Pu(IV)/Pu(III) redox reaction and the results were compared with that of single-walled carbon nanotubes modified GC (SWCNTs/GC) and glassy carbon (GC) electrodes. Graphene catalyzes the exchange of current of the Pu(IV)/Pu(III) couple by reducing both the anodic and cathodic overpotentials. The Gr/GC electrode shows higher peak currents (i p ) and smaller peak potential separation (ΔE p ) values than the SWCNTs/GC and GC electrodes. The heterogeneous electron transfer rate constants (k s ), charge transfer coefficients (α) and the diffusion coefficients (D) involved in the electrocatalytic redox reaction were determined. Our observations show that graphene is best electrocatalytic material among both the SWCNTs and GC to study Pu(IV)/Pu(III) redox reaction.

  20. Results of a Phase 2 Study Examining the Effects of Omitting Elective Neck Irradiation to Nodal Levels IV and V{sub b} in Patients With N{sub 0-1} Nasopharyngeal Carcinoma

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Jian-zhou [Department of Radiation Oncology, Cancer Hospital of Shantou University Medical College, Shantou, Guangdong (China); Le, Quynh-Thu [Department of Radiation Oncology, Stanford University School of Medicine, Stanford, California (United States); Han, Fei; Lu, Li-Xia; Huang, Shao-Min; Lin, Cheng-Guang; Deng, Xiao-Wu; Cui, Nian-Ji [State Key Laboratory of Oncology in South China, Department of Radiation Oncology, Cancer Center of Sun Yat-Sen University, Guangzhou, Guangdong (China); Zhao, Chong, E-mail: gzzhaochong@hotmail.com [State Key Laboratory of Oncology in South China, Department of Radiation Oncology, Cancer Center of Sun Yat-Sen University, Guangzhou, Guangdong (China)

    2013-03-15

    Purpose: To evaluate the patterns of nodal failure and toxicity in clinically negative necks of N{sub 0-1} nasopharyngeal carcinoma (NPC) patients who were treated with intensity modulated radiation therapy (IMRT) but did not receive elective neck irradiation (ENI) to level IV and V{sub b} nodes. Methods and Materials: We conducted a phase 2 prospective study in N{sub 0-1} NPC patients treated with IMRT. ENI included the retropharyngeal nodes and levels II to V{sub a} but omitted levels IV and V{sub b} in clinically negative necks. Patterns of nodal failure, regional control (RC), and late toxicity were evaluated. Results: Between 2001 and 2008, a total of 212 patients (128 N{sub 0} and 84 N{sub 1}) were enrolled in the study. Seven patients (4 in-field and 3 out-of-field) developed nodal failure. One patient (0.5%) developed nodal failure at level V{sub b}, but no patients developed nodal failure at level IV. The 5-year RC rates of the entire group, N{sub 0} patients and N{sub 1} patients were 95.6%, 98.2%, and 91.3%, respectively. Fifteen patients (7.1%) developed distant metastases. The 5-year distant failure-free survival (DFFS) and overall survival (OS) rates were 91.4% and 89.8%, respectively. The rates of grade 2 or greater skin dystrophy, subcutaneous fibrosis and xerostomia were 6.2%, 16.6%, and 17.9%, respectively. Conclusions: The rate of out-of-field nodal failure when omitting ENI to levels IV and V{sub b} in clinically negative necks of patients with N{sub 0-1} NPC was extremely low; therefore, a further phase 3 study is warranted.

  1. Phase transition sequence in ferroelectric Aurivillius compounds investigated by single crystal X-ray diffraction

    Science.gov (United States)

    Boullay, P.; Tellier, J.; Mercurio, D.; Manier, M.; Zuñiga, F. J.; Perez-Mato, J. M.

    2012-09-01

    The investigation of the phase transition sequence in SrBi2Ta2O9 (SBT) and SrBi2Nb2O9 (SBN) is reported using single-crystal X-ray diffraction. By monitoring specific reflections as a function of temperature, sensitive either to the superstructure formation or to polar displacements, it was possible to check the existence or not of an intermediate phase. This latter was confirmed in SBT, but within experimental accuracy could not be detected in SBN.

  2. Investigations of binary and ternary phase change alloys for future memory applications

    Energy Technology Data Exchange (ETDEWEB)

    Rausch, Pascal

    2012-09-13

    The understanding of phase change materials is of great importance because it enables us to predict properties and tailor alloys which might be even better suitable to tackle challenges of future memory applications. Within this thesis two topics have been approached: on the one hand the understanding of the alloy In{sub 3}Sb{sub 1}Te{sub 2} and on the other hand the so called resistivity drift of amorphous Ge-Sn-Te phase change materials. The main topic covers an in depth discussion of the ternary alloy In{sub 3}Sb{sub 1}Te{sub 2}. At first glance, this alloy does not fit into the established concepts of phase alloys: e.g. the existence of resonant bonding in the crystalline phase is not obvious and the number of p-electrons is very low compared to other phase change alloys. Furthermore amorphous phase change alloys with high indium content are usually not discussed in literature, an exception being the recent work by Spreafico et al. on InGeTe{sub 2}. For the first time a complete description of In{sub 3}Sb{sub 1}Te{sub 2} alloy is given in this work for the crystalline phase, amorphous phase and crystallization process. In addition comparisons are drawn to typical phase change materials like Ge{sub 2}Sb{sub 2}Te{sub 5}/GeTe or prototype systems like AgInTe{sub 2} and InTe. The second topic of this thesis deals with the issue of resistivity drift, i.e. the increase of resistivity of amorphous phase change alloys with aging. This drift effect greatly hampers the introduction of multilevel phase change memory devices into the market. Recently a systematic decrease of drift coefficient with stoichiometry has been observed in our group going from GeTe over Ge{sub 3}Sn{sub 1}Te{sub 4} to Ge{sub 2}Sn{sub 2}Te{sub 4}. These alloys are investigated with respect to constraint theory.

  3. Experimental investigation of phase equilibria in the Zr-Cu-Ni ternary system

    International Nuclear Information System (INIS)

    Yang, Mujin; Wang, Cuiping; Yang, Shuiyuan; Shi, Zhan; Han, Jiajia; Liu, Xingjun

    2017-01-01

    The phase equilibria in the Zr-Cu-Ni ternary system are investigated combined with X-ray diffraction, electron probe micro-analysis and differential scanning calorimetry. Two isothermal sections of the Zr-Cu-Ni ternary system at 1 000 C and 1 100 C are experimentally established. Most of the binary intermetallic compounds, e.g. Zr 7 Ni 10 , ZrNi, ZrNi 5 , Zr 14 Cu 51 , and Zr 2 Cu 9 , show a remarkable ternary solubility. A new ternary compound named τ 3 (Zr 31.1-30.7 . Cu 28.5-40.3 Ni 40.4-29.0 ) is detected at 1 000 C and dissolved at 1 020 C because the nearby large liquid phase field further expands. The newly determined phase equilibria will provide important information for both thermodynamic assessment and alloy design of Zr-based metallic glass.

  4. Numerical investigation of multichannel laser beam phase locking in turbulent atmosphere

    Energy Technology Data Exchange (ETDEWEB)

    Volkov, V A; Volkov, M V; Garanin, S G; Starikov, F A [Russian Federal Nuclear Center ' All-Russian Research Institute of Experimental Physics' , Sarov, Nizhnii Novgorod region (Russian Federation)

    2015-12-31

    The efficiency of coherent multichannel beam combining under focusing through a turbulent medium on a target in the cases of phase conjugation and target irradiation in the feedback loop is investigated numerically in various approximations. The conditions of efficient focusing of multichannel radiation on the target are found. It is shown that the coherent beam combining with target irradiation in the feedback loop, which does not require a reference beam and wavefront measurements, is as good as the phase conjugation approach in the efficiency of focusing. It is found that the main effect of focusing is provided by properly chosen phase shifts in the channels, whereas taking into account local wavefront tip tilts weakly affects the result. (control of laser radiation parameters)

  5. Main phases of siting for nuclear power plants with review of required investigations

    International Nuclear Information System (INIS)

    Malbasa, N.

    1984-01-01

    The purpose of the article is a short description of the main phases in the process of siting for nuclear power plants as interpreted and applied by the Institut za elektroprivredu, Zagreb in the screening, comparison and evaluation of the sites for NPPs in the SR of Croatia. The scope and purpose, as well as review of required data and investigations for each particular phase are given. Common used methods for the comparison of sites are described and example of rejection criteria applicable for early phases of the siting is proposed. It is given a list of the most important activities which detailed analysis id indispensable for ending of the evaluation and getting a site permit from the regulatory body. A legal and regulatory basis for carrying out the siting process is also described. (author)

  6. Investigation of the phase separation of PNIPAM using infrared spectroscopy together with multivariate data analysis

    DEFF Research Database (Denmark)

    Munk, Tommy; Baldursdottir, Stefania G.; Hietala, S.

    2013-01-01

    and Gaussian peak fitting was used to investigate the structural changes in aqueous solutions of a polymer, using poly(N-isopropyl acrylamide) (PNIPAM) in the atactic form and with controlled tacticity as a model system. Subtle spectral changes associated with the dehydration and phase separation upon heating...... included peak shifts, an area ratio change of the amide I band to the amide II band and formation of a new peak in the amide I band were efficiently detected. Dehydration and phase separation of PNIPAM occurred in two temperature ranges, one for the atactic and one for isotactic rich part, both involving...... a complex re-organization of the hydrogen bonds and change of the hydration layer. The changes agreed with existing results from other techniques, and new insights were gained into the effect of controlled tacticity on phase transformation behaviour. The study demonstrates that infrared spectroscopy...

  7. Simulation Based Investigation of Focusing Phased Array Ultrasound in Dissimilar Metal Welds

    Directory of Open Access Journals (Sweden)

    Hun-Hee Kim

    2016-02-01

    Full Text Available Flaws at dissimilar metal welds (DMWs, such as reactor coolant systems components, Control Rod Drive Mechanism (CRDM, Bottom Mounted Instrumentation (BMI etc., in nuclear power plants have been found. Notably, primary water stress corrosion cracking (PWSCC in the DMWs could cause significant reliability problems at nuclear power plants. Therefore, phased array ultrasound is widely used for inspecting surface break cracks and stress corrosion cracks in DMWs. However, inspection of DMWs using phased array ultrasound has a relatively low probability of detection of cracks, because the crystalline structure of welds causes distortion and splitting of the ultrasonic beams which propagates anisotropic medium. Therefore, advanced evaluation techniques of phased array ultrasound are needed for improvement in the probability of detection of flaws in DMWs. Thus, in this study, an investigation of focusing and steering phased array ultrasound in DMWs was carried out using a time reversal technique, and an adaptive focusing technique based on finite element method (FEM simulation. Also, evaluation of focusing performance of three different focusing techniques was performed by comparing amplitude of phased array ultrasonic signals scattered from the targeted flaw with three different time delays.

  8. Ternary Phase-Separation Investigation of Sol-Gel Derived Silica from Ethyl Silicate 40

    Science.gov (United States)

    Wang, Shengnan; Wang, David K.; Smart, Simon; Diniz da Costa, João C.

    2015-01-01

    A ternary phase-separation investigation of the ethyl silicate 40 (ES40) sol-gel process was conducted using ethanol and water as the solvent and hydrolysing agent, respectively. This oligomeric silica precursor underwent various degrees of phase separation behaviour in solution during the sol-gel reactions as a function of temperature and H2O/Si ratios. The solution composition within the immiscible region of the ES40 phase-separated system shows that the hydrolysis and condensation reactions decreased with decreasing reaction temperature. A mesoporous structure was obtained at low temperature due to weak drying forces from slow solvent evaporation on one hand and formation of unreacted ES40 cages in the other, which reduced network shrinkage and produced larger pores. This was attributed to the concentration of the reactive sites around the phase-separated interface, which enhanced the condensation and crosslinking. Contrary to dense silica structures obtained from sol-gel reactions in the miscible region, higher microporosity was produced via a phase-separated sol-gel system by using high H2O/Si ratios. This tailoring process facilitated further condensation reactions and crosslinking of silica chains, which coupled with stiffening of the network, made it more resistant to compression and densification. PMID:26411484

  9. Investigation of diode parameters using I-V and C-V characteristics of In/SiO{sub 2}/p-Si (MIS) Schottky diodes

    Energy Technology Data Exchange (ETDEWEB)

    Yueksel, O.F. [Department of Physics, Faculty of Arts and Science, Selcuk University, Kampus, Konya 42075 (Turkey)], E-mail: fyuksel@selcuk.edu.tr; Selcuk, A.B.; Ocak, S.B. [PK, 14 Etlik, Ankara (Turkey)

    2008-08-01

    A study on interface states density distribution and characteristic parameters of the In/SiO{sub 2}/p-Si (MIS) capacitor has been made. The thickness of the SiO{sub 2} film obtained from the measurement of the corrected capacitance in the strong accumulation region for MIS Schottky diodes was 220 A. The diode parameters from the forward bias I-V characteristics such as ideality factor, series resistance and barrier heights were found to be 1.75, 106-112 {omega} and 0.592 eV, respectively. The energy distribution of the interface state density D{sub it} was determined from the forward bias I-V characteristics by taking into account the bias dependence of the effective barrier height. The interface state density obtained using the I-V characteristics had an exponential growth, with bias towards the top of the valance band, from 9.44x10{sup 13} eV{sup -1} cm{sup -2} in 0.329-E{sub v} eV to 1.11x10{sup 13} eV{sup -1} cm{sup -2} in 0.527-E{sub v} eV at room temperature. Furthermore, the values of interface state density D{sub it} obtained by the Hill-Coleman method from the C-V characteristics range from 52.9x10{sup 13} to 1.11x10{sup 13} eV{sup -1} cm{sup -2} at a frequency range of 30kHz-1 MHz. These values of D{sub it} and R{sub s} were responsible for the non-ideal behaviour of I-V and C-V characteristics.

  10. Investigation of Phase Transition-Based Tethered Systems for Small Body Sample Capture

    Science.gov (United States)

    Quadrelli, Marco; Backes, Paul; Wilkie, Keats; Giersch, Lou; Quijano, Ubaldo; Scharf, Daniel; Mukherjee, Rudranarayan

    2009-01-01

    This paper summarizes the modeling, simulation, and testing work related to the development of technology to investigate the potential that shape memory actuation has to provide mechanically simple and affordable solutions for delivering assets to a surface and for sample capture and possible return to Earth. We investigate the structural dynamics and controllability aspects of an adaptive beam carrying an end-effector which, by changing equilibrium phases is able to actively decouple the end-effector dynamics from the spacecraft dynamics during the surface contact phase. Asset delivery and sample capture and return are at the heart of several emerging potential missions to small bodies, such as asteroids and comets, and to the surface of large bodies, such as Titan.

  11. Neutron spin-echo investigation of the microemulsion dynamics. in bicontinuous lamellar and droplet phases

    CERN Document Server

    Mihailescu, M; Endo, H; Allgaier, J; Gompper, G; Stellbrink, J; Richter, D; Jakobs, B; Sottmann, T; Faragó, B

    2002-01-01

    Using neutron spin-echo (NSE) spectroscopy in combination with dynamic light scattering (DLS), we performed an extensive investigation of the bicontinuous phase in ternary water-surfactant-oil microemulsions, with extension to lamellar and droplet phases. The dynamical behavior of surfactant monolayers of decyl-polyglycol-ether (C sub 1 sub 0 E sub 4) molecules, or mixtures of surfactant with long amphiphilic block-copolymers of type poly-ethylene propylene/poly-ethylene oxide (PEP-PEO) was studied, under comparable conditions. The investigation techniques provide access to different length scales relative to the characteristic periodicity length of the microemulsion structure. Information on the elastic bending modulus is obtained from the local scale dynamics in view of existing theoretical descriptions and is found to be in accordance with small angle neutron scattering (SANS) studies. Evidence for the modified elastic properties and additional interaction of the amphiphilic layers due to the polymer is mo...

  12. Investigation of phase diagrams for cylindrical Ising nanotube using cellular automata

    Science.gov (United States)

    Astaraki, M.; Ghaemi, M.; Afzali, K.

    2018-05-01

    Recent developments in the field of applied nanoscience and nanotechnology have heightened the need for categorizing various characteristics of nanostructures. In this regard, this paper establishes a novel method to investigate magnetic properties (phase diagram and spontaneous magnetization) of a cylindrical Ising nanotube. Using a two-layer Ising model and the core-shell concept, the interactions within nanotube has been modelled. In the model, both ferromagnetic and antiferromagnetic cases have been considered. Furthermore, the effect of nanotube's length on the critical temperature is investigated. The model has been simulated using cellular automata approach and phase diagrams were constructed for different values of inter- and intra-layer couplings. For the antiferromagnetic case, the possibility of existence of compensation point is observed.

  13. Experimental investigations of two-phase flow measurement using ultrasonic sensors

    OpenAIRE

    Abbagoni, Baba Musa

    2016-01-01

    This thesis presents the investigations conducted in the use of ultrasonic technology to measure two-phase flow in both horizontal and vertical pipe flows which is important for the petroleum industry. However, there are still key challenges to measure parameters of the multiphase flow accurately. Four methods of ultrasonic technologies were explored. The Hilbert-Huang transform (HHT) was first applied to the ultrasound signals of air-water flow on horizontal flow for measur...

  14. Investigation of the {Fe}/{Si} interface and its phase transformations

    Science.gov (United States)

    Fanciulli, M.; Degroote, S.; Weyer, G.; Langouche, G.

    1997-04-01

    Thin 57Fe films (3-10 Å) have been grown by molecular beam epitaxy (MBE) on (7 × 7) reconstructed Si(111) and (2 × 1) reconstructed Si(001) surfaces and by e-gun evaporation on an H-terminated Si(111) surface. Conversion electron Mössbauer spectroscopy (CEMS) with high statistical accuracy and resolution allowed a detailed microscopic investigation of the silicide formation mechanism and of the structural phase transformations upon annealing.

  15. Radiative acoustic investigation of metals in the area of structural phase transition

    International Nuclear Information System (INIS)

    Kalinichenko, A.I.; Popov, G.F.

    1989-01-01

    Consideration is given to results of experimental investigations of temperature dependences of Grueneisen parameter (GP) and sound velocity for alloys with the effect of shape memory (Cu-Al-Ni and Ni-Ti) and gadolinium in the region of their structural phase transformations. Effect of thermal and spatial GP nonlinearity on the type of excited acoustic wave, as well as possibility of determining function of GP dependence with respect to nonlinear thermoacoustic response of irradiated substance are discussed

  16. The possibility of using dc conductivity for investigating phase transition in amorphous semiconductors

    International Nuclear Information System (INIS)

    El-Mously, M.K.; Mina, N.K.

    1985-07-01

    Different formulas have been applied to deduce the effective or the generalized electrical conductivity of double phase systems. These formulas have been revised and fitted to the experimental data of the binary systems amorphous-crystal (a-c) and liquid-crystal (l-c) for pure elementary selenium and selenium doped by different other elements. Both connected medium and statistical mixture theories can be applied depending on the nature of the system under investigation. (author)

  17. Laboratory, Computational and Theoretical Investigations of Ice Nucleation and its Implications for Mixed Phase Clouds

    Science.gov (United States)

    Yang, Fan

    Ice particles in atmospheric clouds play an important role in determining cloud lifetime, precipitation and radiation. It is therefore important to understand the whole life cycle of ice particles in the atmosphere, e.g., where they come from (nucleation), how they evolve (growth), and where they go (precipitation). Ice nucleation is the crucial step for ice formation, and in this study, we will mainly focus on ice nucleation in the lab and its effect on mixed-phase stratiform clouds. In the first half of this study, we investigate the relevance of moving contact lines (i.e., the region where three or more phases meet) on the phenomenon of contact nucleation. High speed video is used to investigate heterogeneous ice nucleation in supercooled droplets resting on cold substrates under two different dynamic conditions: droplet electrowetting and droplet vibration. The results show that contact-line motion is not a sufficient condition to trigger ice nucleation, while locally curved contact lines that can result from contact-line motion are strongly related to ice nucleation. We propose that pressure perturbations due to locally curved contact lines can strongly enhance the ice nucleation rate, which gives another interpretation for the mechanism for contact nucleation. Corresponding theoretical results provide a quantitative connection between pressure perturbations and temperature, providing a useful tool for ice nucleation calculations in atmospheric models. In this second half of the study, we build a minimalist model for long lifetime mixed-phase stratiform clouds based on stochastic ice nucleation. Our result shows that there is a non-linear relationship between ice water contact and ice number concentration in the mixed-phase cloud, as long as the volume ice nucleation rate is constant. This statistical property may help identify the source of ice nuclei in mixed-phase clouds. In addition, results from Lagrangian ice particle tracking in time dependent fields

  18. Thermodynamic analysis and phase equilibria investigation in Pb−Zn−Ag system

    Directory of Open Access Journals (Sweden)

    Mitovski Aleksandra M.

    2010-01-01

    Full Text Available Physico-chemical processes that take place during the refining process in the extractive metallurgy of lead, are connected with ternary Pb−Zn−Ag system, which is necessary to study from the theoretical practical and aspects. Such investigation is important from production point of view, because of the phenomena that occur during desilvering of lead which is one of the important stages during lead refining process. Process of lead desilvering binds to ternary system Pb−Zn−Ag, which was the reason for numerous investigations, both from thermodynamic point of view and in terms of testing and determining the phase diagram, bearing in mind the theoretical, and practical importance of knowledge about the processes which are going in investigated system. The paper presents the results of thermodynamic analysis and investigation of phase equilibria of the Pb−Zn−Ag ternary system using the method of thermodynamic predictions and phase diagrams calculations, respectively, and the experimental results of metalography obtained by optical microscopy. Phase diagram of the vertical section Pb−Zn80Ag20 is presented, obtained by CALPHAD calculation methodology, and using PANDAT thermodynamic software, compared to experimental results obtained by DTA analysis. The results show a pronounced break in solubility, which is characteristic for the whole ternary Pb−Zn−Ag system. Also, it can be noticed that the thermodynamic properties follow the behavior of this system, which is expressed through positive deviation of Raoult’s law, pointing to the lack of lead affinity compared to the other two components in the system. The optical microscopy results of the investigated system show the following: - Sample L1 (weight% Pb = 98: the structure of the observed section shows double eutectic (Pbsol+Zn−Agsol which lies in the base of the primary crystals of lead (Pbsol - Samples L2−L5: the structure consists of a dual eutectic (Pbsol+Zn−Agsol and

  19. Hydrogeological and hydrogeochemical investigations in boreholes - Final report of the phase I geochemical investigations of the Stripa groundwaters

    International Nuclear Information System (INIS)

    Nordstroem, D.K.; Carlsson, L.; Fontes, J.C.; Frits, P.; Moser, H.; Olsson, T.

    1985-07-01

    The hydrogeochemical investigations of Phase I of the Stripa Project (1980-1984) have been completed, and the results are presented in this final report. All chemical and isotopic data on the groundwaters from the beginning to the Stripa Project to the present (1977-84) are tabulated an used in the final interpretations. The background geology and hydrology is summarized and updated along with new analyses of the Stripa grantie. Water-rock interactions form a basic framework for the changes in major-element chemistry with depth, including carbonate geochemistry, the fluid-inclusion hypothesis, redox processes, and mineral precipitation. The irregular distribution of chloride suggests channelling is occurring and the effect of thermomechanical perturbations on the groundwater chemistry is documented. Stable and radioactive isotpes provide information of the origin and evolution of the groundwater itself and of several elments within the groundwater. Subsurface production of radionuclides is documented in these investigations, and a general picture of uranium transformations during weathering is presented. One of the primary conclusions reached in these studies is that different dissolved constituents will provide different residence times because they have different origins and different evolutionary histories that may or may not be related to the overall evolution of the groundwater itself. (author)

  20. Experimental investigation and thermodynamic calculations of the Ag–Bi–Ga phase diagram

    Energy Technology Data Exchange (ETDEWEB)

    Minić, Duško, E-mail: dminic65@open.telekom.rs [University in Priština, Faculty of Technical Science, Kos. Mitrovica (Serbia); Premović, Milena [University in Priština, Faculty of Technical Science, Kos. Mitrovica (Serbia); Manasijević, Dragan [University of Belgrade, Technical Faculty, Bor (Serbia); Ćosović, Vladan [University of Belgrade, Institute of Chemistry, Technology and Metallurgy, Belgrade (Serbia); Živković, Dragana [University of Belgrade, Technical Faculty, Bor (Serbia); Marković, Aleksandar [University in Priština, Faculty of Technical Science, Kos. Mitrovica (Serbia)

    2015-10-15

    Phase diagram of the Ag–Bi–Ga ternary system was investigated using differential thermal analysis (DTA), scanning electron microscopy (SEM) with energy dispersive spectrometry (EDS), and x-ray powder diffraction (XRD) methods. Experimentally obtained results were compared with the results of thermodynamic prediction of phase equilibria based on calculation of phase diagram (CALPHAD) method. Phase transition temperatures of alloys with overall compositions along three selected vertical sections Ag–Bi{sub 50}Ga{sub 50}, Bi–Ag{sub 50}Ga{sub 50} and Ga–Ag{sub 50}Bi{sub 50} were measured by DTA. Liquidus temperatures were experimentally determined and compared with the results of thermodynamic calculation. Identification of coexisting phases in samples equilibrated at 200 °C was carried out using SEM-EDS and XRD methods. Obtained results were compared with the calculated isothermal section of the Ag–Bi–Ga ternary system at corresponding temperature. Calculated liquidus projection and invariant equilibria of the Ag–Bi–Ga ternary system were presented. The obtained values were found to be in a close agreement. - Highlights: • Calculated constitutive binary system based on literature data. • Experimentally determined (DTA) temperatures of phase transformations compared with analytical calculation. • Definition of three vertical sections Ag–Bi{sub 50}Ga{sub 50}, Bi–Ag{sub 50}Ga{sub 50} and Ga–Ag{sub 50}Bi{sub 50}. • Calculated horizontal section at 200 °C, confirmed by experimental SEM-EDS and XRD method. • Calculated liquidus surface projection and determined invariant reaction occurred in ternary Ag–Bi–Ga system.

  1. Phase sensitive molecular dynamics of self-assembly glycolipid thin films: A dielectric spectroscopy investigation

    Science.gov (United States)

    Velayutham, T. S.; Ng, B. K.; Gan, W. C.; Majid, W. H. Abd.; Hashim, R.; Zahid, N. I.; Chaiprapa, Jitrin

    2014-08-01

    Glycolipid, found commonly in membranes, is also a liquid crystal material which can self-assemble without the presence of a solvent. Here, the dielectric and conductivity properties of three synthetic glycolipid thin films in different thermotropic liquid crystal phases were investigated over a frequency and temperature range of (10-2-106 Hz) and (303-463 K), respectively. The observed relaxation processes distinguish between the different phases (smectic A, columnar/hexagonal, and bicontinuous cubic Q) and the glycolipid molecular structures. Large dielectric responses were observed in the columnar and bicontinuous cubic phases of the longer branched alkyl chain glycolipids. Glycolipids with the shortest branched alkyl chain experience the most restricted self-assembly dynamic process over the broad temperature range studied compared to the longer ones. A high frequency dielectric absorption (Process I) was observed in all samples. This is related to the dynamics of the hydrogen bond network from the sugar group. An additional low-frequency mechanism (Process II) with a large dielectric strength was observed due to the internal dynamics of the self-assembly organization. Phase sensitive domain heterogeneity in the bicontinuous cubic phase was related to the diffusion of charge carriers. The microscopic features of charge hopping were modelled using the random walk scheme, and two charge carrier hopping lengths were estimated for two glycolipid systems. For Process I, the hopping length is comparable to the hydrogen bond and is related to the dynamics of the hydrogen bond network. Additionally, that for Process II is comparable to the bilayer spacing, hence confirming that this low-frequency mechanism is associated with the internal dynamics within the phase.

  2. Investigation for vertical, two-phase steam-water flow of three turbine models

    International Nuclear Information System (INIS)

    Silverman, S.; Goodrich, L.D.

    1977-01-01

    One of the basic quantities of interest during a loss-of-coolant experiment (LOCE) is the primary system mass flow rate. Presently, there are no transducers commercially available which continuously measure this parameter. Therefore, a transducer was designed at EG and G Idaho, Inc. which combines a drag-disc and turbine into a single unit. The basis for the design was that the drag-disc would measure momentum flux (rhoV 2 ), the turbine would measure velocity and the mass flow rate could then be calculated from the two quantities by assuming a flow profile. For two-phase flow, the outputs are approximately proportional to the desired parameter, but rather large errors can be expected under those assumptions. Preliminary evaluation of the experimental two- and single-phase calibration data has resulted in uncertainty estimates of +-8% of range for the turbine and +-20% of range for the drag-disc. In an effort to reduce the errors, further investigations were made to determine what the drag-disc and turbine really measure. In the present paper, three turbine models for vertical, two-phase, steam/water flow are investigated; the Aya Model, the Rouhani Model, and a volumetric flow model. Theoretical predictions are compared with experimental data for vertical, two-phase steam/water flow. For the purposes of the mass flow calculation, velocity profiles were assumed to be flat for the free-field condition. It is appreciated that this may not be true for all cases investigated, but for an initial inspection, flat profiles were assumed

  3. In situ neutron diffraction investigation on the phase transformation sequence of kaolinite and halloysite to mullite

    Energy Technology Data Exchange (ETDEWEB)

    Tezuka, Nobuo [Department of Applied Physics, Curtin University of Technology, GPO Box U1987, Perth, WA 6845 (Australia); Low, It-Meng [Department of Applied Physics, Curtin University of Technology, GPO Box U1987, Perth, WA 6845 (Australia)]. E-mail: J.Low@curtin.edu.au; Davies, Ian J. [Department of Mechanical Engineering, Curtin University of Technology, GPO Box U1987, Perth, WA 6845 (Australia); Prior, Michael [Bragg Institute, ANSTO, PMB 1, Menai, NSW 2234 (Australia); Studer, Andrew [Bragg Institute, ANSTO, PMB 1, Menai, NSW 2234 (Australia)

    2006-11-15

    'Kaolin' is a major raw material for the fabrication of conventional ceramics. In this work the authors have investigated the thermal phase transformation of mullite from two different types of kaolin (kaolinite and halloysite), with or without alumina matrix constraint, during heating up to 1500 deg. C and then cooling using in situ neutron diffraction. Mullitization was initiated upon heating to 1200 deg. C for all specimens and followed spinel formation at 1100 deg. C. Above this temperature, however, evolution of the main phases, i.e., mullite, cristobalite and corundum, was influenced by the presence of impurities, initial type of silica, and alumina constraint. The relative amount of mullite was largest for the pure kaolinite specimen, particularly during heating, and this was attributed to the presence of a glassy phase. However, kaolinite with alumina suppressed the crystallization of cristobalite from the glassy phase upon cooling due to a reaction between alumina and amorphous silica, consequently resulting in an amount of mullite as for the pure kaolinite specimen (approximately 65 wt%). Halloysite was less active in terms of mullitization due to the lower level of initial impurities and greater amount of cristobalite, particularly for the alumina-constrained specimen. However, the final amount of mullite derived from the pure halloysite specimen was similar to that as from the kaolinite specimen.

  4. In situ neutron diffraction investigation on the phase transformation sequence of kaolinite and halloysite to mullite

    International Nuclear Information System (INIS)

    Tezuka, Nobuo; Low, It-Meng; Davies, Ian J.; Prior, Michael; Studer, Andrew

    2006-01-01

    'Kaolin' is a major raw material for the fabrication of conventional ceramics. In this work the authors have investigated the thermal phase transformation of mullite from two different types of kaolin (kaolinite and halloysite), with or without alumina matrix constraint, during heating up to 1500 deg. C and then cooling using in situ neutron diffraction. Mullitization was initiated upon heating to 1200 deg. C for all specimens and followed spinel formation at 1100 deg. C. Above this temperature, however, evolution of the main phases, i.e., mullite, cristobalite and corundum, was influenced by the presence of impurities, initial type of silica, and alumina constraint. The relative amount of mullite was largest for the pure kaolinite specimen, particularly during heating, and this was attributed to the presence of a glassy phase. However, kaolinite with alumina suppressed the crystallization of cristobalite from the glassy phase upon cooling due to a reaction between alumina and amorphous silica, consequently resulting in an amount of mullite as for the pure kaolinite specimen (approximately 65 wt%). Halloysite was less active in terms of mullitization due to the lower level of initial impurities and greater amount of cristobalite, particularly for the alumina-constrained specimen. However, the final amount of mullite derived from the pure halloysite specimen was similar to that as from the kaolinite specimen

  5. Experimental investigation of phase equilibria in the Co-W-V ternary system

    International Nuclear Information System (INIS)

    Liu Xingjun; Zhu Yihong; Yu Yan; Wang Cuiping

    2011-01-01

    Highlights: → Three isothermal sections of the Co-W-V ternary system at 1100 deg. C, 1200 deg. C and 1300 deg. C were determined. → No ternary compound was found in the Co-W-V ternary system. → A stable liquid miscibility gap is newly discovered in the Co-W-V ternary system. → This work is of great essence to establish the thermodynamic database for the Co-based alloys. - Abstract: The phase equilibria in the Co-W-V ternary system were experimentally investigated by optical microscopy (OM), electron probe microanalysis (EPMA) and X-ray diffraction (XRD) on the equilibrated alloys. Three isothermal sections of the Co-W-V ternary system at 1100 deg. C, 1200 deg. C and 1300 deg. C were determined, and no ternary compound was found in this system. In addition, a novel phenomena induced by the liquid phase separation in the Co-W-V alloys was firstly discovered, suggesting that a stable liquid miscibility gap exists in the Co-W-V ternary system. The newly determined phase equilibria and firstly discovered phase separation phenomena in the Co-W-V system will provide important information for the development of Co-W based alloys.

  6. Investigation of phase-change coatings for variable thermal control of spacecraft

    Science.gov (United States)

    Kelliher, W. C.; Young, P. R.

    1972-01-01

    An investigation was conducted to determine the feasibility of producing a spacecraft coating system that could vary the ratio of its solar absorptance to thermal emittance to adjust automatically for changes in the thermal balance of a spacecraft. This study resulted in a new concept called the phase-change effect which uses the change that occurs in the optical properties of many materials during the phase transition from a crystalline solid to an amorphous material. A series of two-component model coatings was developed which, when placed on a highly reflecting substrate, exhibited a sharp decrease in solar absorptance within a narrow temperature range. A variable thermal control coating can have a significant amount of temperature regulation with the phase-change effect. Data are presented on several crystallite-polymer formulations, their physical and optical properties, and associated phase-change temperatures. Aspects pertaining to their use in a space environment and an example of the degree of thermal regulation attainable with these coatings is also given.

  7. Investigation of liquid phase axial dispersion in Taylor bubble flow by radiotracer residence time distribution analysis

    Directory of Open Access Journals (Sweden)

    Jin J.H.

    2013-05-01

    Full Text Available A gas-liquid Taylor bubble flow occurs in small diameter channels in which gas bubbles are separated by slugs of pure liquid. This type of flow regime is well suited for solid catalyzed gas-liquid reactors in which the reaction efficiency is a strong function of axial dispersion in the regions of pure liquid. This paper presents an experimental study of liquid phase axial dispersion in a Taylor bubble flow developed in a horizontal tube using high speed photography and radiotracer residence time distribution (RTD analysis. A parametric dependence of axial dispersion on average volume fraction of gas phase was also investigated by varying the relative volumetric flow rates of the two phases. 137mBa produced from a 137Cs/137mBa radionuclide generator was used as radiotracer and measurements were made using the NaI(Tl scintillation detectors. Validation of 137mBa in the form of barium chloride as aqueous phase radiotracer was also carried out. Axial Dispersion Model (ADM was used to simulate the hydrodynamics of the system and the results of the experiment are presented. It was observed that the system is characterized by very high values of Peclet Number (Pe∼102 which reveals an approaching plug type flow. The experimental and model estimated values of mean residence times were observed in agreement with each other.

  8. Laboratory investigations of the alpha-pinene/ozone gas-phase reaction

    International Nuclear Information System (INIS)

    Benner, C.L.

    1985-01-01

    In order to provide more insight into terpene photooxidation or ozonolysis reaction mechanisms, a radiotracer technique was developed. This technique was applied to an investigation of the 14 C-alpha-pinene/ozone reaction. In the first phase of the research, the carbon distribution at the conclusion of the ozonolysis reaction was determined by separating carbon-14-labelled gaseous products from labelled aerosols, and counting each phase by liquid scintillation methods. The resulting carbon balance was 38% to 60% filtered aerosols, 6% to 20% gas phase compounds, and 11% to 29% products absorbed on the reaction chamber walls. Recoveries of the alpha-pinene carbon-14 ranging from 79% to 97% were achieved using this method. The alpha-pinene concentrations in these experiments were close to ambient (1 part per billion), yet the carbon balance was similar to that observed at much higher concentrations (>1 part per million). In the second phase of the alpha-pinene study, both gas and aerosol products of the ozonolysis reaction were collected on cartridges impregnated with 2,4-dinitrophenylhydrazine, then analyzed by HPLC. In the final experiments, alpha-pinene aerosol was reacted with a silylating agent to improve the detection of organic acids and alcohols. The gas chromatographic/mass spectrometric analysis of the silylated aerosol products showed evidence of dimer/polymer formation occurring in the ozonolysis reaction

  9. Synthesis, Structure and Investigation of Germanium(IV and Copper(II Complexes with Malic Acid and 1,10ʹ-phenanthroline

    Directory of Open Access Journals (Sweden)

    Inna Seifullina

    2017-12-01

    Full Text Available Two crystalline compounds of germanium(IV with malic acid (HMal and 1,10ʹ-phenanthroline (phen - [Ge(HMal2(phen]•pheh•2H2O (I and [CuCl(phen2][Ge(OH(HMal2] (II were synthesized for the first time and characterized by elemental analysis, IR-spectroscopy and thermogravimetric analysis. There was elucidated from single-crystal X-ray diffraction that two different forms of Germanium are implemented: Ge4+ (I and hydrolyzed GeOH3+ (II to form distorted octahedron and pyramid respectively.

  10. Investigations on the transverse phase space at a photo injector for minimized emittance

    Energy Technology Data Exchange (ETDEWEB)

    Miltchev, V.

    2006-08-15

    Radio frequency photoinjectors are electron sources able to generate beams of extremely high brightness, which are applicable to linac driven Free Electron Lasers (FEL). Because of the high phase space density, the dynamics of the electron beam is dominated by space charge interactions between the particles. This thesis studies the transverse phase space of space charge dominated electron beams produced by the Photo Injector Test Facility in Zeuthen (PITZ). The operation conditions for minimizing the transverse emittance are studied experimentally, theoretically and in simulations. The influence of the longitudinal profile of the driving UV laser pulse on the transverse emittance is investigated. Emphasis is placed on the experimental study of the emittance as a function of different machine parameters like the laser beam spot size, the amplitude of the focusing magnetic field, the rf phase and the electron bunch charge. First investigations on the thermal emittance for Cs{sub 2}Te photocathodes under rf operating conditions are presented. Measurements of the thermal emittance scaling with the photocathode laser spot size are analyzed. The significance of the applied rf field in the emittance formation process is discussed. (orig.)

  11. Spin-orientation phase transitions in cubic ferrimagnetic GdIG: magnetooptic and visual investigation

    International Nuclear Information System (INIS)

    Eremenko, V.V.; Kharchenko, N.F.; Gnatchenko, S.L.

    1976-01-01

    The sharp and smooth magnetic transitions due to the magnetic field in the canting process of the magnetic sublattices of GdIG are investigated by measuring the Faraday rotation in the small section of the sample and by the visualization of the magnetic structure in the polarized light. The investigations were made near the magnetic compensation temperature at the orientation H along the [111] and [100] axes. The Faraday rotation of the different magnetic phases was measured in the vicinity of the phase transitions between the collinear and canted structures and also between different canted ones. The visual observations were used to construct the phase diagrams and the magnetic state coexistence regions. Particular attention was paid to the critical point (the case H parallel [100]). Above the definite field the transition between the low- and high-temperature noncollinear states occurs smoothly. The experimental results are compared with the calculations carried out in the molecular field approximation making allowance for the three-sublattice structure of GdIG

  12. Classical and quantum investigations of four-dimensional maps with a mixed phase space

    International Nuclear Information System (INIS)

    Richter, Martin

    2012-01-01

    Systems with more than two degrees of freedom are of fundamental importance for the understanding of problems ranging from celestial mechanics to molecules. Due to the dimensionality the classical phase-space structure of such systems is more difficult to understand than for systems with two or fewer degrees of freedom. This thesis aims for a better insight into the classical as well as the quantum mechanics of 4D mappings representing driven systems with two degrees of freedom. In order to analyze such systems, we introduce 3D sections through the 4D phase space which reveal the regular and chaotic structures. We introduce these concepts by means of three example mappings of increasing complexity. After a classical analysis the systems are investigated quantum mechanically. We focus especially on two important aspects: First, we address quantum mechanical consequences of the classical Arnold web and demonstrate how quantum mechanics can resolve this web in the semiclassical limit. Second, we investigate the quantum mechanical tunneling couplings between regular and chaotic regions in phase space. We determine regular-to-chaotic tunneling rates numerically and extend the fictitious integrable system approach to higher dimensions for their prediction. Finally, we study resonance-assisted tunneling in 4D maps.

  13. Experimental investigation and CFD simulation of horizontal stratified two-phase flow phenomena

    International Nuclear Information System (INIS)

    Vallee, Christophe; Hoehne, Thomas; Prasser, Horst-Michael; Suehnel, Tobias

    2008-01-01

    For the investigation of stratified two-phase flow, two horizontal channels with rectangular cross-section were built at Forschungszentrum Dresden-Rossendorf (FZD). The channels allow the investigation of air/water co-current flows, especially the slug behaviour, at atmospheric pressure and room temperature. The test-sections are made of acrylic glass, so that optical techniques, like high-speed video observation or particle image velocimetry (PIV), can be applied for measurements. The rectangular cross-section was chosen to provide better observation possibilities. Moreover, dynamic pressure measurements were performed and synchronised with the high-speed camera system. CFD post-test simulations of stratified flows were performed using the code ANSYS CFX. The Euler-Euler two fluid model with the free surface option was applied on grids of minimum 4 x 10 5 control volumes. The turbulence was modelled separately for each phase using the k-ω-based shear stress transport (SST) turbulence model. The results compare very well in terms of slug formation, velocity, and breaking. The qualitative agreement between calculation and experiment is encouraging and shows that CFD can be a useful tool in studying horizontal two-phase flow

  14. Experimental investigation and CFD simulation of horizontal stratified two-phase flow phenomena

    International Nuclear Information System (INIS)

    Vallee, Christophe; Hohne, Thomas; Prasser, Horst-Michael; Suhnel, Tobias

    2007-01-01

    For the investigation of stratified two-phase flow, two horizontal channels with rectangular cross-section were built at Forschungszentrum Rossendorf. The channels allow the investigation of air/water co-current flows, especially the slug behaviour, at atmospheric pressure and room temperature. The test-sections are made of acrylic glass, so that optical techniques, like high-speed video observation or particle image velocimetry (PIV), can be applied for measurements. The rectangular cross-section was chosen to provide better observation possibilities. Moreover, dynamic pressure measurements were performed and synchronized with the high-speed camera system. CFD post test simulations of stratified flows were performed using the code ANSYS CFX. The Euler- Euler two fluid model with the free surface option was applied on grids of minimum 4.10 5 control volumes. The turbulence was modelled separately for each phase using the k-ω based shear stress transport (SST) turbulence model. The results compare very well in terms of slug formation, velocity, and breaking. The qualitative agreement between calculation and experiment is encouraging and shows that CFD can be a useful tool in studying horizontal two-phase flow. (authors)

  15. Experimental investigation and CFD simulation of horizontal stratified two-phase flow phenomena

    Energy Technology Data Exchange (ETDEWEB)

    Vallee, Christophe [Forschungszentrum Dresden-Rossendorf e.V., Dresden (Germany)], E-mail: c.vallee@fzd.de; Hoehne, Thomas; Prasser, Horst-Michael; Suehnel, Tobias [Forschungszentrum Dresden-Rossendorf e.V., Dresden (Germany)

    2008-03-15

    For the investigation of stratified two-phase flow, two horizontal channels with rectangular cross-section were built at Forschungszentrum Dresden-Rossendorf (FZD). The channels allow the investigation of air/water co-current flows, especially the slug behaviour, at atmospheric pressure and room temperature. The test-sections are made of acrylic glass, so that optical techniques, like high-speed video observation or particle image velocimetry (PIV), can be applied for measurements. The rectangular cross-section was chosen to provide better observation possibilities. Moreover, dynamic pressure measurements were performed and synchronised with the high-speed camera system. CFD post-test simulations of stratified flows were performed using the code ANSYS CFX. The Euler-Euler two fluid model with the free surface option was applied on grids of minimum 4 x 10{sup 5} control volumes. The turbulence was modelled separately for each phase using the k-{omega}-based shear stress transport (SST) turbulence model. The results compare very well in terms of slug formation, velocity, and breaking. The qualitative agreement between calculation and experiment is encouraging and shows that CFD can be a useful tool in studying horizontal two-phase flow.

  16. Investigations on the transverse phase space at a photo injector for minimized emittance

    International Nuclear Information System (INIS)

    Miltchev, V.

    2006-08-01

    Radio frequency photoinjectors are electron sources able to generate beams of extremely high brightness, which are applicable to linac driven Free Electron Lasers (FEL). Because of the high phase space density, the dynamics of the electron beam is dominated by space charge interactions between the particles. This thesis studies the transverse phase space of space charge dominated electron beams produced by the Photo Injector Test Facility in Zeuthen (PITZ). The operation conditions for minimizing the transverse emittance are studied experimentally, theoretically and in simulations. The influence of the longitudinal profile of the driving UV laser pulse on the transverse emittance is investigated. Emphasis is placed on the experimental study of the emittance as a function of different machine parameters like the laser beam spot size, the amplitude of the focusing magnetic field, the rf phase and the electron bunch charge. First investigations on the thermal emittance for Cs 2 Te photocathodes under rf operating conditions are presented. Measurements of the thermal emittance scaling with the photocathode laser spot size are analyzed. The significance of the applied rf field in the emittance formation process is discussed. (orig.)

  17. Absorption in a three-phase fluidized bed I: Hydrodynamic investigations

    Directory of Open Access Journals (Sweden)

    Pejanović Srđan M.

    2003-01-01

    Full Text Available The hydrodynamic properties of a three phase fluidized bed with low density inert spherical packing, fluidized by the interaction of a gas flowing upwards and a liquid flowing downwards through the column, were investigated. It was found that the pressure drop, liquid hold up and dynamic bed height increase with both increasing liquid and gas flow rate. While the dynamic bed height and minimum fluidization velocity remain unchanged, both the pressure drop and liquid hold up increase with increasing density of the packing. Therefore, an increase in packing density causes more intensive mass transfer between the fluid phases than packed columns. It was shown that increase of the liquid flow rate causes an increase of both the effective liquid and gas velocity through the fluidized bed, which may also improve mass transfer.

  18. Transmission electron microscopy investigation of interfaces in a two-phase TiAl alloy

    Science.gov (United States)

    Mahon, G. J.; Howe, J. M.

    1990-06-01

    The atomic structures of the γ/α2 and γ/γT interfaces in a TiAl alloy were investigated using conventional and high-resolution transmission electron microscopy (TEM) in order to understand the growth mechanisms and deformation behavior of the two-phase alloy. The results show that the α2 plates grow from the γ phase by the migration of a/6 partial dislocation ledges across the faces and that the γ/α2 interface usually contains closely spaced arrays of interfacial dislocations. Deformation twins cut through both γ twin boundaries and α2 plates during deformation, although slip of twinning c slocations through α2 appears to be a difficult process. Both the γ/α2 and γ/γT interfaces can be imaged and modeled at the atomic level, although slight crystal and/or beam tilt can complicate image interpretation.

  19. Investigation on a Sensitive Chemiluminescence System Based on Ni(IV Complex to Determine Two β2-Agonist Drugs in Urine and Swine Feed and Their Mechanism

    Directory of Open Access Journals (Sweden)

    Xiao Dong

    2018-04-01

    Full Text Available Veterinary drug residues, particularly traces of β2-agonists, can cause various kinds of harmful impact to the environment and public health. Here, a sensitive chemiluminescence (CL method incorporated with a flow injection analysis is developed for the determination of two β2-agonists [i.e., salbutamol (SAL and terbutaline (TEB]. The system is based on the CL reaction of Ni(IV complex with luminol in alkaline solutions, whereas SAL and TEB can significantly enhance CL intensities. Under optimum conditions, CL intensities are proportional to the SAL and TEB concentration in the range of 1.0 × 10−9 M to 5.0 × 10−7 M and 1.0 × 10−9 M to 1.0 × 10−7 M, respectively. The limits of detection (3σ are 1.0 × 10−11 M for TEB, and 1.3 × 10−11 for SAL respectively. Relative standard deviations (n = 11 are less than 2% for 5.0 × 10−8 M SAL and TEB. Possible reaction mechanisms for the CL system are suggested based on the CL system spectra, Ni(IV complex oxidation characteristics, and electron spin resonance (ESR techniques. The proposed method has been applied to the analysis of urine and swine feed samples with satisfactory results.

  20. An investigation of phase transitions in solid methane and deuterated derivatives to pressures of 3 kbar

    International Nuclear Information System (INIS)

    Sprik, M.

    1982-01-01

    The first part of this thesis is an experimental investigation of the interaction responsible for the I-II transition and the second part comprises three theoretical studies of several of the properties of phase I and II. The first chapter of part I, is a general introduction to a thermodynamic treatment of the isotope effect in an orientational phase transition. The thermodynamic approach yields a corresponding state model for the phase diagrams of the five isotopes of methane (CH 4 , CHD 3 , CH 2 D 2 , CH 3 D and CD 4 ). In the remaining two chapters of part I, the corresponding state relation mentioned above is applied to the I-II transition of methane in order to obtain an experimental value for the effective exponent n of the dependence on intermolecular separation of the ordering anisotropic interaction. Part II starts with a derivation of a quasi-classical approximation to the statistical density matrix of a free spherical top. While the orientational system is treated classically, the consequences of the other characteristic of the methane molecules are considered, i.e. the high approximately odd symmetry of the molecule (the octupole field in phase II is odd under spatial inversion). It is argued that the renormalization group analysis of critical phenomena in certain highly complicated antiferromagnetic systems may be equally well applied to the I-II transition in methane. Finally, the study of the quantum effect in phase II is resumed. The spin lattice relaxation time at very low temperature is calculated from first principles using an orientational dynamical process of purely quantum-mechanical nature. (Auth.)

  1. Numerical investigation on critical heat flux and coolant volume required for transpiration cooling with phase change

    International Nuclear Information System (INIS)

    He, Fei; Wang, Jianhua

    2014-01-01

    Highlights: • Five states during the transpiration cooling are discussed. • A suit of applicable program is developed. • The variations of the thickness of two-phase region and the pressure are analyzed. • The relationship between heat flux and coolant mass flow rate is presented. • An approach is given to define the desired case of transpiration cooling. - Abstract: The mechanism of transpiration cooling with liquid phase change is numerically investigated to protect the thermal structure exposed to extremely high heat flux. According to the results of theoretical analysis, there is a lower critical and an upper critical external heat flux corresponding a certain coolant mass flow rate, between the two critical values, the phase change of liquid coolant occurs within porous structure. A strongly applicable self-edit program is developed to solve the states of fluid flow and heat transfer probably occurring during the phase change procedure. The distributions of temperature and saturation in these states are presented. The variations of the thickness of two-phase region and the pressure including capillary are analyzed, and capillary pressure is found to be the main factor causing pressure change. From the relationships between the external heat flux and coolant mass flow rate obtained at different cooling cases, an approach is given to estimate the maximal heat flux afforded and the minimal coolant consumption required by the desired case of transpiration cooling. Thus the pressure and coolant consumption required in a certain thermal circumstance can be determined, which are important in the practical application of transpiration cooling

  2. Investigations on the growth kinetics of Laves phase precipitates in 12% Cr creep-resistant steels: Experimental and DICTRA calculations

    International Nuclear Information System (INIS)

    Prat, O.; Garcia, J.; Rojas, D.; Carrasco, C.; Inden, G.

    2010-01-01

    The growth kinetics of Laves phase precipitates (type Fe 2 W) in the early stage of creep (650 deg. C for 10,000 h) in two 12% Cr ferrite-martensitic steels has been investigated. In one alloy the Laves phase formed on tempering, while in the second alloy the Laves phase precipitated during creep. Kinetic simulations were performed using the software DICTRA. The particle size of the Laves phase was measured on transmission electron microscopy samples. The equilibrium phase fraction of the Laves phase was reached in the first thousand hours. Simulations of particle growth showed good agreement with the experimental results. Competitive growth between M 23 C 6 and the Laves phase showed that M 23 C 6 carbides reached their equilibrium after 12 days, whereas the Laves phase reached equilibrium after 3 months. Simulations of the influence of the interfacial energy and addition of Co, Cu and Si on Laves phase precipitation are presented.

  3. Numerical investigation of the early flight phase in ski-jumping.

    Science.gov (United States)

    Gardan, N; Schneider, A; Polidori, G; Trenchard, H; Seigneur, J M; Beaumont, F; Fourchet, F; Taiar, R

    2017-07-05

    The purpose of this study is to develop a numerical methodology based on real data from wind tunnel experiments to investigate the effect of the ski jumper's posture and speed on aerodynamic forces in a wide range of angles of attack. To improve our knowledge of the aerodynamic behavior of the ski jumper and his equipment during the early flight phase of the ski jump, we applied CFD methodology to evaluate the influence of angle of attack (α=14°, 21.5°, 29°, 36.5° and 44°) and speed (u=23, 26 and 29m/s) on aerodynamic forces in the situation of stable attitude of the ski jumper's body and skis. The standard k-ω turbulence model was used to investigate both the influence of the ski jumper's posture and speed on aerodynamic performance during the early flight phase. Numerical results show that the ski jumper's speed has very little impact on the lift and drag coefficients. Conversely, the lift and drag forces acting on the ski jumper's body during the early flight phase of the jump are strongly influenced by the variations of the angle of attack. The present results suggest that the greater the ski jumper's angle of inclination, with respect to the relative flow, the greater the pressure difference between the lower and upper parts of the skier. Further studies will focus on the dependency of the parameters with both the angle of attack α and the body-ski angle β as control variables. It will be possible to test and optimize different ski jumping styles in different ski jumping hills and investigate different environmental conditions such as temperature, altitude or crosswinds. Copyright © 2017 Elsevier Ltd. All rights reserved.

  4. Investigation of a Novel NDE Method for Monitoring Thermomechanical Damage and Microstructure Evolution in Ferritic-Martensitic Steels for Generation IV Nuclear Energy Systems

    Energy Technology Data Exchange (ETDEWEB)

    Nagy, Peter

    2013-09-30

    The main goal of the proposed project is the development of validated nondestructive evaluation (NDE) techniques for in situ monitoring of ferritic-martensitic steels like Grade 91 9Cr-1Mo, which are candidate materials for Generation IV nuclear energy structural components operating at temperatures up to ~650{degree}C and for steam-generator tubing for sodium-cooled fast reactors. Full assessment of thermomechanical damage requires a clear separation between thermally activated microstructural evolution and creep damage caused by simultaneous mechanical stress. Creep damage can be classified as "negligible" creep without significant plastic strain and "ordinary" creep of the primary, secondary, and tertiary kind that is accompanied by significant plastic deformation and/or cavity nucleation and growth. Under negligible creep conditions of interest in this project, minimal or no plastic strain occurs, and the accumulation of creep damage does not significantly reduce the fatigue life of a structural component so that low-temperature design rules, such as the ASME Section III, Subsection NB, can be applied with confidence. The proposed research project will utilize a multifaceted approach in which the feasibility of electrical conductivity and thermo-electric monitoring methods is researched and coupled with detailed post-thermal/creep exposure characterization of microstructural changes and damage processes using state-of-the-art electron microscopy techniques, with the aim of establishing the most effective nondestructive materials evaluation technique for particular degradation modes in high-temperature alloys that are candidates for use in the Next Generation Nuclear Plant (NGNP) as well as providing the necessary mechanism-based underpinnings for relating the two. Only techniques suitable for practical application in situ will be considered. As the project evolves and results accumulate, we will also study the use of this technique for monitoring other GEN IV

  5. QUEOS, an experimental investigation of the premixing phase with hot spheres

    Energy Technology Data Exchange (ETDEWEB)

    Meyer, L. [Forschungszentrum Karlsruhe GmbH Technik und Umwelt (Germany). Inst. fuer Neutronenphysik und Reaktortechnik

    1998-01-01

    A second series of experiments with hot spheres to investigate the premixing phase of a steam explosion has been performed in the QUEOS facility at FZK. The diameter of the sphere jet plunging into the water has been reduced from 180 mm to 100 mm and larger masses have been employed. Both changes led to longer pours, compared to the short pours in the first series. The data of seven experiments are presented using three types of spheres at 1800 K and total volumes of approximately two and four liters, respectively. High speed films were taken, pressures, water temperatures and the steaming rate were measured. (author)

  6. Investigation on U - O - Na, Pu - O - Na and U,Pu - O - Na phase diagrams

    International Nuclear Information System (INIS)

    Pillon, S.

    1989-03-01

    The thermochemical interaction between the nuclear fuel (uranium and plutonium mixed oxides) and the sodium has been investigated and particularly the three phase diagrams: U - O - Na; Pu - O - Na; U,Pu - O - Na. High temperature neutron diffraction, microcalorimetry and powder X-ray diffraction were used for the characterization of the compounds synthetized. This study allowed to complete the knowledge about each of these diagrams and to measure some physical and thermal properties on the compounds. The limits on the modelization of the fuel-sodium interaction are discussed from the results of the UO 2 - Na reaction [fr

  7. Experimental investigation of densification of powdered A15 phase in the system Nb--Al--Ge

    International Nuclear Information System (INIS)

    Modi, D.P.

    1976-02-01

    An investigation of the densification of precompounded powder of the A15 phase Nb 3 (Al,Ge) was made. The influence of various parameters such as additives, temperature, pressure and time in sintering of this material was studied. Since cold pressing followed by sintering did not produce sufficient density, the hot pressing technique was used. By hot pressing at 1450 0 C for 1 / 2 hour under 6 ksi pressure, about 95 percent densification was achieved. Results provide information that could lead to the development of a viable process for producing superconductors based on this compound. 14 figures, 17 references

  8. Investigation of heat transfer of tube line of staggered tube bank in two-phase flow

    Science.gov (United States)

    Jakubcionis, Mindaugas

    2015-06-01

    This article presents the results of experimental investigation of heat transfer process, carried out using the model of heat exchanger. Two-phase statically stable foam flow was used as a heat transfer fluid. Heat exchanger model consisted of staggered tube bank. Experimental results are presented with the focus on influence of tube position in the line of the bank, volumetric void component and velocity of gas component of the foam. The phenomena of liquid draining in cellular foam flow and its influence on heat transfer rate has also been discussed. The experimental results have been generalized by relationship between Nusselt, Reynolds and Prandtl numbers.

  9. Modeling phase equilibria for acid gas mixtures using the CPA equation of state. Part IV. Applications to mixtures of CO2 with alkanes

    DEFF Research Database (Denmark)

    Tsivintzelis, Ioannis; Ali, Shahid; Kontogeorgis, Georgios

    2015-01-01

    The thermodynamic properties of pure gaseous, liquid or supercritical CO2 and CO2 mixtures with hydrocarbons and other compounds such as water, alcohols, and glycols are very important in many processes in the oil and gas industry. Design of such processes requires use of accurate thermodynamic...... models, capable of predicting the complex phase behavior of multicomponent mixtures as well as their volumetric properties. In this direction, over the last several years, the cubic-plus-association (CPA) thermodynamic model has been successfully used for describing volumetric properties and phase...

  10. IV treatment at home

    Science.gov (United States)

    ... Other IV treatments you may receive after you leave the hospital include: Treatment for hormone deficiencies Medicines for severe nausea that cancer chemotherapy or pregnancy may cause Patient-controlled analgesia (PCA) for pain (this is IV ...

  11. Gatifloxacin phase IV surveillance trial (TeqCES study) utilizing 5000 primary care physician practices: report of pathogens isolated and susceptibility patterns in community-acquired respiratory tract infections.

    Science.gov (United States)

    Pfaller, Michael A; Jones, Ronald N

    2002-09-01

    Recently FDA-approved fluoroquinolones like gatifloxacin possess enhanced activity against Gram-positive pathogens such as Streptococcus pneumoniae. However, experience with adverse events among previously used fluoroquinolones has led to expanded post-marketing investigations of clinical efficacy and safety. An open-label gatifloxacin trial was initiated in early 2000, using 2795 (>15000 enrolled cases) primary care providers for treatment of community-acquired respiratory tract infections (CARTI) such as community-acquired pneumonia (CAP), acute bacterial exacerbation of chronic bronchitis (ABECB), acute sinusitis. Microbiology specimens and sputum slides were referred to a reference laboratory, pathogens identified and reference antimicrobial susceptibility tests performed. Results were classified by infection site, geographic census region and patient profile/demographics. The most frequent pathogens were: for CAP (n = 384)-S. pneumoniae (37%) > Hemophilus influenzae (31%) > Moraxella catarrhalis (13%); for ABECB (528)-H. influenzae (37%) > M. catarrhalis (26%) > S. pneumoniae (17%); and for sinusitis (2691)-M. catarrhalis (29%) > H. influenzae (24%) > S. pneumoniae (17%). H. parainfluenzae (ABECB) and S. aureus (sinusitis) were also commonly isolated. CAP S. pneumoniae isolates had significantly less high-level resistance (5% at > or =2 micro g/ml) than those isolates from ABECB or sinusitis (13-15%). United States census zone differences in S. pneumoniae resistance were identified (greatest in West or East South Central, South Atlantic). S. pneumoniae macrolide resistance was high (23-33%) and H. influenzae clarithromycin susceptibility was only 56-62%. beta-lactamase rates in H. influenzae and M. catarrhalis were 21-29% and 88-92%, respectively. Only one S. pneumoniae was not susceptible to gatifloxacin, and this new fluoroquinolone was fourfold more potent than levofloxacin (MIC(50,) 0.25 vs. 1 micro g/ml). This Phase IV surveillance trial (Teq

  12. Pitavastatin 4 mg Provides Significantly Greater Reduction in Remnant Lipoprotein Cholesterol Compared With Pravastatin 40 mg: Results from the Short-term Phase IV PREVAIL US Trial in Patients With Primary Hyperlipidemia or Mixed Dyslipidemia.

    Science.gov (United States)

    Miller, P Elliott; Martin, Seth S; Joshi, Parag H; Jones, Steven R; Massaro, Joseph M; D'Agostino, Ralph B; Sponseller, Craig A; Toth, Peter P

    2016-03-01

    Remnants are partially hydrolyzed, triglyceride-rich lipoproteins that are implicated in atherosclerosis. We assessed the adequacy of pitavastatin 4 mg and pravastatin 40 mg in reducing atherogenic lipid parameters beyond LDL-C, in particular remnant lipoprotein cholesterol (RLP-C). From the Phase IV, multicenter, randomized, double-blind PREVAIL US (A Study of Pitavastatin 4 mg Vs. Pravastatin 40 mg in Patients With Primary Hyperlipidemia or Mixed Dyslipidemia) trial, we examined lipoprotein cholesterol subfractions using Vertical Auto Profile testing and apolipoproteins B and A-I at baseline and 12 weeks. Participants with primary hyperlipidemia or mixed dyslipidemia had LDL-C levels of 130 to 220 mg/dL and triglyceride levels ≤ 400 mg/dL. In this post hoc analysis, changes in lipid parameters were compared by using ANCOVA. Lipoprotein subfraction data were available in 312 patients (pitavastatin, n = 157; pravastatin, n = 155). Pitavastatin promoted a greater reduction in RLP-C than pravastatin (-13.6 [8.7] vs -9.3 [9.5] mg/dL). Furthermore, the pitavastatin group reported greater reductions in both components of RLP-C (both, P < 0.001): intermediate-density lipoprotein cholesterol (-9.5 [6.3] vs -6.4 [6.6] mg/dL) and very low-density lipoprotein cholesterol subfraction 3 (-4.1 [3.5] vs -2.9 [3.8] mg/dL). There were also greater reductions in the major ratios of risk (apolipoprotein B/apolipoprotein A-I and total cholesterol/HDL-C) (both, P < 0.001). There were no significant changes in HDL-C, its subfractions, or natural log lipoprotein(a)-cholesterol. The mean age was 58.8 ± 8.9 years in the pitavastatin group and 57.0 ± 10.2 years in the pravastatin group. Compared with pravastatin 40 mg daily, pitavastatin 4 mg provided superior reductions in atherogenic lipid parameters beyond LDL-C, including RLP-C. Future studies are needed investigate the clinical implications of lowering directly measured RLP-C as the principal target. ClinicalTrials.gov identifier

  13. Experimental investigation of phase equilibria in the Zr-Cu-Ni ternary system

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Mujin; Wang, Cuiping; Yang, Shuiyuan; Shi, Zhan; Han, Jiajia; Liu, Xingjun [Xiamen Univ. (China). College of Materials and Fujian Provincial Key Lab. of Materials Genome

    2017-08-15

    The phase equilibria in the Zr-Cu-Ni ternary system are investigated combined with X-ray diffraction, electron probe micro-analysis and differential scanning calorimetry. Two isothermal sections of the Zr-Cu-Ni ternary system at 1 000 C and 1 100 C are experimentally established. Most of the binary intermetallic compounds, e.g. Zr{sub 7}Ni{sub 10}, ZrNi, ZrNi{sub 5}, Zr{sub 14}Cu{sub 51}, and Zr{sub 2}Cu{sub 9}, show a remarkable ternary solubility. A new ternary compound named τ{sub 3} (Zr{sub 31.1-30.7} . Cu{sub 28.5-40.3}Ni{sub 40.4-29.0}) is detected at 1 000 C and dissolved at 1 020 C because the nearby large liquid phase field further expands. The newly determined phase equilibria will provide important information for both thermodynamic assessment and alloy design of Zr-based metallic glass.

  14. Investigating heterogeneous nucleation in peritectic materials via the phase-field method

    International Nuclear Information System (INIS)

    Emmerich, Heike; Siquieri, Ricardo

    2006-01-01

    Here we propose a phase-field approach to investigate the influence of convection on peritectic growth as well as the heterogeneous nucleation kinetics of peritectic systems. For this purpose we derive a phase-field model for peritectic growth taking into account fluid flow in the melt, which is convergent to the underlying sharp interface problem in the thin interface limit (Karma and Rappel 1996 Phys. Rev. E 53 R3017). Moreover, we employ our new phase-field model to study the heterogeneous nucleation kinetics of peritectic material systems. Our approach is based on a similar approach towards homogeneous nucleation in Granasy et al (2003 Interface and Transport Dynamics (Springer Lecture Notes in Computational Science and Engineering vol 32) ed Emmerich et al (Berlin: Springer) p 190). We applied our model successfully to extend the nucleation rate predicted by classical nucleation theory for an additional morphological term relevant for peritectic growth. Further applications to understand the mechanisms and consequences of heterogeneous nucleation kinetics in more detail are discussed

  15. Experimental investigation of the Zr corner of the ternary Zr-Nb-Fe phase diagram

    Energy Technology Data Exchange (ETDEWEB)

    Granovsky, M.S. E-mail: granovsk@cnea.gov.ar; Canay, M.; Lena, E.; Arias, D

    2002-04-01

    Intermediate phases in the Zr-rich region of the Zr-Nb-Fe system have been investigated by X-ray diffraction, optical and electron microscopy and electron microprobe analysis. The chemical composition ranges covered by the alloys studied here are: (41-97) at.% Zr, (32-0.9) at.% Nb and (0.6-38) at.% Fe. The phases found in this region were: the solid solutions {alpha}-Zr and {beta}-Zr, the intermetallic Zr{sub 3}Fe with less than 0.2 at.% Nb in solution, two new ternary intermetallic compounds (Zr+Nb){sub 2}Fe '{lambda}{sub 1}' with a cubic Ti{sub 2}Ni-type structure in the composition range (2.4-13) at.% Nb and (31-33) at.% Fe, and (Fe+Nb){sub 2}Zr '{lambda}{sub 2}' indexed as hexagonal Laves phase MgZn{sub 2} type (C14) with a wide range of compositions close to (35-37) at.% Zr, (12-31) at.% Nb and (32-53) at.% Fe.

  16. Experimental investigation of the Zr corner of the ternary Zr-Nb-Fe phase diagram

    International Nuclear Information System (INIS)

    Granovsky, M.S.; Canay, M.; Lena, E.; Arias, D.

    2002-01-01

    Intermediate phases in the Zr-rich region of the Zr-Nb-Fe system have been investigated by X-ray diffraction, optical and electron microscopy and electron microprobe analysis. The chemical composition ranges covered by the alloys studied here are: (41-97) at.% Zr, (32-0.9) at.% Nb and (0.6-38) at.% Fe. The phases found in this region were: the solid solutions α-Zr and β-Zr, the intermetallic Zr 3 Fe with less than 0.2 at.% Nb in solution, two new ternary intermetallic compounds (Zr+Nb) 2 Fe 'λ 1 ' with a cubic Ti 2 Ni-type structure in the composition range (2.4-13) at.% Nb and (31-33) at.% Fe, and (Fe+Nb) 2 Zr 'λ 2 ' indexed as hexagonal Laves phase MgZn 2 type (C14) with a wide range of compositions close to (35-37) at.% Zr, (12-31) at.% Nb and (32-53) at.% Fe

  17. Vibrational spectroscopic and dielectric properties investigations of phase transitions in KMgPO4 compound

    Science.gov (United States)

    Miladi, L.; Oueslati, A.; Guidara, K.

    2017-11-01

    The potassium orthophosphate KMgPO4 with a β-tridymite structure was synthesized via solid-state reaction. X-ray diffraction study confirms the formation of a single phase material which crystallizes at room temperature in monoclinic system. This compound has been investigated by vibrational spectroscopy in the temperature range573-723 K. Thermal analysis shows that this composition undergoes two phase transitions at T1=633Kand T2=693 K.The evolution of Raman line ν and half -width Δν versus temperature introduces huge changes which are associated with the phase transitions originating from the reorientation of the PO4 tetrahedron. Besides, an analysis of the dielectric constants ε‧ and ε″versus temperature at several frequencies shows a distribution of relaxation times. This relaxation is probably due to the change in dynamical state of the K+ cation. The ac conductivity behavior can be understood in terms of the motions of K+ cations along the tunnels which are formed by six-membered rings of MgO4 and PO4 tetrahedron linked by common vertices. The activation energies values obtained from the thermal evolution of the conductivity are: Ea1=0.52 eV (T693 K).

  18. Numerical investigation of refrigeration machine compressor operation considering single-phase electric motor dynamic characteristics

    Science.gov (United States)

    Baidak, Y.; Smyk, V.

    2017-08-01

    Using as the base the differential equations system which was presented in relative units for generalized electric motor of hermetic refrigeration compressor, mathematical model of the software for dynamic performance calculation of refrigeration machine compressors drive low-power asynchronous motors was developed. Performed on its ground calculations of the basic model of two-phase electric motor drive of hermetic compressor and the proposed newly developed model of the motor with single-phase stator winding, which is an alternative to the industrial motor winding, have confirmed the benefits of the motor with innovative stator winding over the base engine. Given calculations of the dynamic characteristics of compressor drive motor have permitted to determine the value of electromagnetic torque swinging for coordinating compressor and motor mechanical characteristics, and for taking them into consideration in choosing compressor elements construction materials. Developed and used in the process of investigation of refrigeration compressor drive asynchronous single-phase motor mathematical and software can be considered as an element of computer-aided design system for design of the aggregate of refrigeration compression unit refrigerating machine.

  19. A Preliminary Experimental Investigation of Wet Fine Erosion in Two-Phase Flow

    Science.gov (United States)

    Ya, H. H.; Luthfi, Haziq; Ngo, Nguyet-Tran; Hassan, Suhaimi; Pao, William

    2018-03-01

    Solid particles below 62 μm is classified as fine. In oil producing operation, the most commonly used downhole sand screen can only capture solid particles of 140 μm and above. Most predictive erosion model is limited to particle size of 100 μm with single phase flow assumption because it is commonly believed that erosion due to particles below 100 μm is insignificant and typically ignored by oil and gas consultants when proposing facilities design. The objective of this paper is to investigate the impact of fines particle on mild steel plate in two-phase flow at different collision angles. A two phase flow loop was set up. The average size of fine particle was 60 μm, mixed with water with sand to water ratio at 1:65 wt/wt. The mild steel plates were oriented at three different impact angles which are -30°, 30° and 90°, with respect to the horizon. Scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), surface roughness and Vickers micro hardness techniques were used to quantify the effects of fine particle on the exposed surface.

  20. Experimental and numerical investigation of a phase-only control mechanism in the linear intensity regime.

    Science.gov (United States)

    Brühl, Elisabeth; Buckup, Tiago; Motzkus, Marcus

    2018-06-07

    Mechanisms and optimal experimental conditions in coherent control still intensely stimulate debates. In this work, a phase-only control mechanism in an open quantum system is investigated experimentally and numerically. Several parameterizations for femtosecond pulse shaping (combination of chirp and multipulses) are exploited in transient absorption of a prototype organic molecule to control population and vibrational coherence in ground and excited states. Experimental results are further numerically simulated and corroborated with a four-level density-matrix model, which reveals a phase-only control mechanism based on the interaction between the tailored phase of the excitation pulse and the induced transient absorption. In spite of performing experiment and numerical simulations in the linear regime of excitation, the control effect amplitude depends non-linearly on the excitation energy and is explained as a pump-dump control mechanism. No evidence of single-photon control is observed with the model. Moreover, our results also show that the control effect on the population and vibrational coherence is highly dependent on the spectral detuning of the excitation spectrum. Contrary to the popular belief in coherent control experiments, spectrally resonant tailored excitation will lead to the control of the excited state only for very specific conditions.

  1. Investigation of two-phase liquid-metal magnetohydrodynamic power systems

    International Nuclear Information System (INIS)

    Amend, W.E.; Fabris, G.; Cutting, J.

    1975-01-01

    A two-phase Liquid-Metal MHD (LMMHD) system is under development at the Argonne National Laboratory, and results are presented for detailed cycle analysis and systems studies, the experimental facility, and the thermal and magneto fluid mechanics problems encountered. The studies indicate that the LMMHD cycle will operate efficiently in the temperature range of 1000-1600 0 F (50 percent efficiency with a maximum cycle temperature of 1600 0 F) and is therefore potentially compatible with many advanced heat sources under development such as the LMFBR, fluidized-bed coal combustor, HTGCR and the fusion reactor. Of special interest is the coupling to the LMFBR thereby eliminating the costly, potentially hazardous liquid-metal/water interface. The results of detailed parametric studies of the heat transfer interfaces between an LMMHD power cycle and an LMFBR and a steam bottoming plant are described. Experimental evaluation of the two-phase LMMHD generator was performed in an ambient temperature NaK--N 2 facility at ANL. Results of these experiments, performed to determine the operating characteristics of the device as a function of the various independent parameters and to investigate two-phase flow, are given. (U.S.)

  2. The experimental investigation of phase equilibria in the Al-rich corner within the ternary Al–Mn–Be system

    Energy Technology Data Exchange (ETDEWEB)

    Zupanič, Franc, E-mail: franc.zupanic@um.si [University of Maribor, Faculty of Mechanical Engineering, Smetanova ulica 17, SI-2000 Maribor (Slovenia); Markoli, Boštjan; Naglič, Iztok [University of Ljubljana, Faculty of Natural Sciences and Technologies, Askerceva 12, Ljubljana SI-1000 (Slovenia); Bončina, Tonica [University of Maribor, Faculty of Mechanical Engineering, Smetanova ulica 17, SI-2000 Maribor (Slovenia)

    2013-09-05

    Highlights: •We investigated the constitution of the Al-rich corner of the Al–Mn–Be system. •Be{sub 4}AlMn is a thermodynamically stable phase in the Al-corner of the Al–Mn–Be system. •The T-phase (Al{sub 15}Mn{sub 3}Be{sub 2}) is not a stable phase in the Al-corner at 600 °C. •The λ-Al{sub 4}Mn phase is a stable phase in the Al-corner at 600 °C. •T-phase is a stable phase at 750 °C. -- Abstract: This work investigated the constitution of the Al-rich corner within the ternary Al–Mn–Be phase diagram using SEM + EDS, AES, XRD and DSC. With respect to the results, an isothermal cross-section at 600 °C was established, as well as a prediction of the apparent liquidus projection in the Al-corner. Be{sub 4}AlMn is a thermodynamically stable phase in the Al-rich corner of the ternary phase diagram. The other ternary T-phase, usually designated as Al{sub 15}Mn{sub 3}Be{sub 2}, formed during solidification in alloys with Be:Mn atomic ratios of less than 4:1, and having more than 1.5 at.% Mn. This phase is not a stable phase in the Al-rich corner at 600 °C. In contrast, the λ-Al{sub 4}Mn phase is a stable one. The T-phase is stable over a rather large part of the phase diagram at least within a temperature range close to 750 °C, where it is in equilibrium with the Al-rich liquid phase, and Be{sub 4}AlMn.

  3. Studies on extraction behaviour of U (VI) and Pu (IV) by Aliquat-336 encapsulated in microporous polymer beads

    International Nuclear Information System (INIS)

    Parikh, K.J.; Kedari, C.S.; Pandit, S.S.; Tripathi, S.C.; Dwivedi, C.; Singh, K.K.; Kumar, M.; Bajaj, P.N.

    2009-01-01

    Aliquat-336 encapsulated microporous polymeric beads (AEPB) were prepared to investigate their applicability for the solid-liquid extraction Pu (IV) from nitric acid solutions. Batch equilibration studies on the extractions of U (VI) and Pu (IV) from aqueous solutions using AEPB have been carried out at different concentrations of nitric acid and sodium nitrate. Extraction of Pu (IV) increases with increasing concentration of nitrate ions in the aqueous phase where as extraction of U (VI) remains less than 5% for all the aqueous conditions studied. Polymeric beads appeared to be less stable at higher nitric acid concentrations as the extraction of Pu (IV) was found to be lowered above 4 M HNO 3 concentration. The maximum Pu (IV) uptake by AEPB was 0.84 μg per mg of beads. Pu (IV)from loaded polymer can be back extracted using dilute nitric acid or ascorbic acid solution. (author)

  4. Horonobe Underground Research Laboratory project. Plans of investigations during shaft and drift excavation (Construction of underground facilities: Phase II)

    International Nuclear Information System (INIS)

    2005-06-01

    Horonobe Underground Research Laboratory Project is planned for over 20 years to establish the scientific and technical basis for the underground disposal of high-level radioactive wastes in Japan. The investigations are conducted by JNC in three phases, from the surface (Phase I), during the construction of the underground facilities (Phase II), and using the facilities (Phase III). This report concerns the investigation plans for Phase II. During excavation of shafts and drifts, detailed geological and borehole investigation will be conducted and the geological model constructed in Phase I is evaluated and revised by newly acquired data of geophysical and geological environment. Detailed in-situ experiments, as well as the effects of shaft excavation, are also done to study long-term changes, rock properties, groundwater flow and chemistry to ensure the reliability of repository technology and establish safety assessment methodology. (S. Ohno)

  5. Local probe investigations of the electronic phase diagrams of iron pnictides and chalcogenides

    Energy Technology Data Exchange (ETDEWEB)

    Materne, Philipp

    2015-09-24

    In this work, the electronic phase diagrams of Ca{sub 1-x}Na{sub x}Fe{sub 2}As{sub 2} and Fe{sub 1+y}Te were investigated using muon spin relaxation and Moessbauer spectroscopy. Single crystals of Ca{sub 1-x}Na{sub x}Fe{sub 2}As{sub 2} with x = 0.00, 0.35, 0.50, and 0.67 were examined. The undoped 122 parent compound CaFe{sub 2}As{sub 2} is a semi metal and shows antiferromagnetic commensurate spin density wave order below 167 K. By hole doping via Na substitution, the magnetic order is suppressed and superconductivity emerges including a Na-substitution level region, where both phases coexist. Upon Na substitution, a tilting of the magnetic moments out of the ab-plane is found. The interaction of the magnetic and superconducting order parameter in this coexistence region was studied and a nanoscopic coexistence of both order parameters is found. This is proven by a reduction of the magnetic order parameter of 7 % in x = 0.50 below the superconducting transition temperature. This reduction was analysed using Landau theory and a systematic correlation between the reduction of the magnetic order parameter and the ratio of the transition temperatures, T{sub c}/T{sub N}, for the 122 family of the iron pnictides is presented. The magnetic phase transition is accompanied by a tetragonal-to-orthorhombic phase transition. The lattice dynamics at temperatures above and below this magneto-structural phase transition were studied and no change in the lattice dynamics were found. However, the lattice for finite x is softer than for the undoped compound. For x = 0.67, diluted magnetic order is found. Therefore, the magnetism in Ca{sub 1-x}Na{sub x}Fe{sub 2}As{sub 2} is persistent even at optimal doping. The superconducting state is investigated by measuring the temperature dependence of the magnetic penetration depth, where two superconducting gaps with a weighting of nearly 50:50 are obtained. A temperature independent anisotropy of the magnetic penetration depth γ{sub

  6. Local probe investigations of the electronic phase diagrams of iron pnictides and chalcogenides

    International Nuclear Information System (INIS)

    Materne, Philipp

    2015-01-01

    In this work, the electronic phase diagrams of Ca 1-x Na x Fe 2 As 2 and Fe 1+y Te were investigated using muon spin relaxation and Moessbauer spectroscopy. Single crystals of Ca 1-x Na x Fe 2 As 2 with x = 0.00, 0.35, 0.50, and 0.67 were examined. The undoped 122 parent compound CaFe 2 As 2 is a semi metal and shows antiferromagnetic commensurate spin density wave order below 167 K. By hole doping via Na substitution, the magnetic order is suppressed and superconductivity emerges including a Na-substitution level region, where both phases coexist. Upon Na substitution, a tilting of the magnetic moments out of the ab-plane is found. The interaction of the magnetic and superconducting order parameter in this coexistence region was studied and a nanoscopic coexistence of both order parameters is found. This is proven by a reduction of the magnetic order parameter of 7 % in x = 0.50 below the superconducting transition temperature. This reduction was analysed using Landau theory and a systematic correlation between the reduction of the magnetic order parameter and the ratio of the transition temperatures, T c /T N , for the 122 family of the iron pnictides is presented. The magnetic phase transition is accompanied by a tetragonal-to-orthorhombic phase transition. The lattice dynamics at temperatures above and below this magneto-structural phase transition were studied and no change in the lattice dynamics were found. However, the lattice for finite x is softer than for the undoped compound. For x = 0.67, diluted magnetic order is found. Therefore, the magnetism in Ca 1-x Na x Fe 2 As 2 is persistent even at optimal doping. The superconducting state is investigated by measuring the temperature dependence of the magnetic penetration depth, where two superconducting gaps with a weighting of nearly 50:50 are obtained. A temperature independent anisotropy of the magnetic penetration depth γ λ = 1.5(4) is obtained, which is much smaller compared to other 122 compounds

  7. Development of methods for measuring materials nuclear characteristics, Phases, I, II, II and IV; Razvijanje metoda merenja nuklearnih karakteristika materijala, I, II, II i VI faza

    Energy Technology Data Exchange (ETDEWEB)

    Maglic, R [Boris Kidric Institute of Nuclear Sciences Vinca, Belgrade (Yugoslavia)

    1963-04-15

    This report contains the following phases of the project 'measurement of nuclear characteristics of reactor materials': nuclear performances of the neutron chopper; method for measuring total effective cross sections by transmission method on the chopper; review of methods for measuring activation cross sections; measurement of neutron spectra of the RA reactor and measurement of total effective cross section of gold by using the chopper.

  8. Temperature Regulation of Photovoltaic Module Using Phase Change Material: A Numerical Analysis and Experimental Investigation

    Directory of Open Access Journals (Sweden)

    Hasan Mahamudul

    2016-01-01

    Full Text Available This work represents an effective design of a temperature regulated PV module by integrating phase change materials for Malaysian weather condition. Through the numerical analysis and experimental investigation it has been shown that if a PCM layer of width 0.02 m of RT 35 is used as a cooling arrangement with a PV module, the surface temperature of the module is reduced by 10°C, which remains constant for a period of 4–6 hours. This reduction of temperature implies the increase in conversion efficiency of the module. Experiment as well as investigation has been carried out considering typical Malaysian weather. Obtained result has been validated by using experimental prototype and comparative analysis.

  9. A Heat Transfer Investigation of Liquid and Two-Phase Methane

    Science.gov (United States)

    VanNoord, Jonathan

    2010-01-01

    A heat transfer investigation was conducted for liquid and two-phase methane. The tests were conducted at the NASA Glenn Research Center Heated Tube Facility (HTF) using resistively heated tube sections to simulate conditions encountered in regeneratively cooled rocket engines. This testing is part of NASA s Propulsion and Cryogenics Advanced Development (PCAD) project. Nontoxic propellants, such as liquid oxygen/liquid methane (LO2/LCH4), offer potential benefits in both performance and safety over equivalently sized hypergolic propulsion systems in spacecraft applications. Regeneratively cooled thrust chambers are one solution for high performance, robust LO2/LCH4 engines, but cooling data on methane is limited. Several test runs were conducted using three different diameter Inconel 600 tubes, with nominal inner diameters of 0.0225-, 0.054-, and 0.075-in. The mass flow rate was varied from 0.005 to 0.07 lbm/sec. As the current focus of the PCAD project is on pressure fed engines for LO2/LCH4, the average test section outlet pressures were targeted to be 200 psia or 500 psia. The heat flux was incrementally increased for each test condition while the test section wall temperatures were monitored. A maximum average heat flux of 6.2 Btu/in.2 sec was achieved and, at times, the temperatures of the test sections reached in excess of 1800 R. The primary objective of the tests was to produce heat transfer correlations for methane in the liquid and two-phase regime. For two-phase flow testing, the critical heat flux values were determined where the fluid transitions from nucleate boiling to film boiling. A secondary goal of the testing was to measure system pressure drops in the two-phase regime.

  10. Investigation of gas-phase decontamination of internally radioactively contaminated gaseous diffusion process equipment and piping

    International Nuclear Information System (INIS)

    Bundy, R.D.; Munday, E.B.

    1991-01-01

    Construction of the gaseous diffusion plants (GDPs) was begun during World War 2 to produce enriched uranium for defense purposes. These plants, which utilized UF 6 gas, were used primarily for this purpose through 1964. From 1959 through 1968, production shifted primarily to uranium enrichment to supply the nuclear power industry. Additional UF 6 -handling facilities were built in feed and fuel-processing plants associated with the uranium enrichment process. Two of the five process buildings at Oak ridge were shut down in 1964. Uranium enrichment activities at Oak Ridge were discontinued altogether in 1985. In 1987, the Department of Energy (DOE) decided to proceed with a permanent shutdown of the Oak Ridge Gaseous Diffusion Plant (ORGDP). DOE intends to begin decommissioning and decontamination (D ampersand D) of ORGDP early in the next century. The remaining two GDPs are expected to be shut down during the next 10 to 40 years and will also require D ampersand D, as will the other UF 6 -handling facilities. This paper presents an investigation of gas- phase decontamination of internally radioactively contaminated gaseous diffusion process equipment and piping using powerful fluorinating reagents that convert nonvolatile uranium compounds to volatile UF 6 . These reagents include ClF 3 , F 2 , and other compounds. The scope of D ampersand D at the GDPs, previous work of gas-phase decontamination, four concepts for using gas-phase decontamination, plans for further study of gas-phase decontamination, and the current status of this work are discussed. 13 refs., 15 figs

  11. Electron microscopic investigations of the as-synthesised and dissociated Y:124 HTSC phases

    International Nuclear Information System (INIS)

    Srivastava, A.K.; Ramakrishna, K.; Srivastava, O.N.

    1992-01-01

    The Y:124 was synthesised at ambient oxygen pressure using an oxygen enhancer (NaNO 3 ). The as-synthesised material was thermally dissociated at 915degC for various time spans, e.g., 1, 2 and 5 min. X-ray diffraction (XRD) results showed that the undissociated sample corresponds to the Y:124 phase, whereas the dissociated samples consisted of mixed phases. For the samples dissociated for 1 min these were Y:124 and Y:123 (with some traces of CuO), for dissociation times of 2 and 5 min these were dominantly Y:123 and CuO. From R-T and L-T (inductance-temperature) measurements, it was found that the undissociated Y:124 possesses a Tc(R=0)∝80 K and there is no drop in inductance for dissociated samples (2 and 5 min). Microstructural investigations of Y:124 revealed that the material dissociated for 1 min is biphasic, consisting of Y:124 and Y:123. Besides stacking disorder, local area superstructures along ''c'' emanating from the native Y:124 phase were also observed. This is thought to ensue from the random and sequential removal of Cu-O chains from the Y:124 structure. The sample subjected to longer dissociation times, i.e., 2 and 5 min consists of Y:123 and CuO precipitates. For longer dissociation times, e.g., 2 min and above, the Y:124 phase nearly completely converts into Y:123 and CuO. (orig.)

  12. Investigating Phase Transform Behavior in Indium Selenide Based RAM and Its Validation as a Memory Element

    Directory of Open Access Journals (Sweden)

    Swapnil Sourav

    2016-01-01

    Full Text Available Phase transform properties of Indium Selenide (In2Se3 based Random Access Memory (RAM have been explored in this paper. Phase change random access memory (PCRAM is an attractive solid-state nonvolatile memory that possesses potential to meet various current technology demands of memory design. Already reported PCRAM models are mainly based upon Germanium-Antimony-Tellurium (Ge2Sb2Te5 or GST materials as their prime constituents. However, PCRAM using GST material lacks some important memory attributes required for memory elements such as larger resistance margin between the highly resistive amorphous and highly conductive crystalline states in phase change materials. This paper investigates various electrical and compositional properties of the Indium Selenide (In2Se3 material and also draws comparison with its counterpart mainly focusing on phase transform properties. To achieve this goal, a SPICE model of In2Se3 based PCRAM model has been reported in this work. The reported model has been also validated to act as a memory cell by associating it with a read/write circuit proposed in this work. Simulation results demonstrate impressive retentivity and low power consumption by requiring a set pulse of 208 μA for a duration of 100 μs to set the PCRAM in crystalline state. Similarly, a reset pulse of 11.7 μA for a duration of 20 ns can set the PCRAM in amorphous state. Modeling of In2Se3 based PCRAM has been done in Verilog-A and simulation results have been extensively verified using SPICE simulator.

  13. Phase 3 Trial of Postoperative Chemotherapy Alone Versus Chemoradiation Therapy in Stage III-IV Gastric Cancer Treated With R0 Gastrectomy and D2 Lymph Node Dissection

    International Nuclear Information System (INIS)

    Kim, Tae Hyun; Park, Sook Ryun; Ryu, Keun Won; Kim, Young-Woo; Bae, Jae-Moon; Lee, Jun Ho; Choi, Il Ju; Kim, Yeon-Joo; Kim, Dae Yong

    2012-01-01

    Purpose: To compare chemotherapy alone with chemoradiation therapy in stage III-IV(M0) gastric cancer treated with R0 gastrectomy and D2 lymph node dissection. Methods and Materials: The chemotherapy arm received 5 cycles of fluorouracil and leucovorin (FL), and the chemoradiation therapy arm received 1 cycle of FL, then radiation therapy of 45 Gy concurrently with 2 cycles of FL, followed by 2 cycles of FL. Intent-to-treat analysis and per-protocol analyses were performed. Results: Between May 6, 2002 and June 29, 2006, a total of 90 patients were enrolled. Forty-four were randomly assigned to the chemotherapy arm and 46 to the chemoradiation therapy arm. Treatment was completed as planned by 93.2% of patients in the chemotherapy arm and 87.0% in the chemoradiation therapy arm. Overall intent-to-treat analysis showed that addition of radiation therapy to chemotherapy significantly improved locoregional recurrence-free survival (LRRFS) but not disease-free survival. In subgroup analysis for stage III, chemoradiation therapy significantly prolonged the 5-year LRRFS and disease-free survival rates compared with chemotherapy (93.2% vs 66.8%, P=.014; 73.5% vs 54.6%, P=.056, respectively). Conclusions: Addition of radiation therapy to chemotherapy could improve the LRRFS in stage III gastric cancer treated with R0 gastrectomy and D2 lymph node dissection.

  14. Final Phase II report : QuickSite(R) investigation, Everest, Kansas.

    Energy Technology Data Exchange (ETDEWEB)

    LaFreniere, L. M. (Environmental Research)

    2003-11-01

    this reason, the CCC/USDA is conducting an environmental site investigation to determine the source(s) and extent of the carbon tetrachloride contamination at Everest and to assess whether the contamination requires remedial action. The investigation at Everest is being performed by the Environmental Research Division of Argonne National Laboratory. Argonne is a nonprofit, multidisciplinary research center operated by the University of Chicago for the U.S. Department of Energy (DOE). The CCC/USDA has entered into an interagency agreement with DOE, under which Argonne provides technical assistance to the CCC/USDA with environmental site characterization and remediation at its former grain storage facilities. At these facilities, Argonne is applying its QuickSite{reg_sign} environmental site characterization methodology. This methodology has been applied successfully at a number of former CCC/USDA facilities in Kansas and Nebraska and has been adopted by the American Society for Testing and Materials (ASTM 1998) as standard practice for environmental site characterization. Phase I of the QuickSite{reg_sign} investigation examined the key geologic, hydrogeologic, and hydrogeochemical relationships that define potential contaminant migration pathways at Everest (Argonne 2001). Phase II of the QuickSite{reg_sign} investigation at Everest was undertaken with the primary goal of delineating and improving understanding of the distribution of carbon tetrachloride contamination in groundwater at this site and the potential source area(s) that might have contributed to this contamination. To address this goal, four specific technical objectives were developed to guide the Phase II field studies. Sampling of near-surface soils at the former Everest CCC/USDA facility that was originally planned for Phase I had to be postponed until October 2000 because of access restrictions. Viable vegetation was not available for sampling then. This period is termed the first session of Phase II

  15. Integrated account of method, site selection and programme prior to the site investigation phase

    International Nuclear Information System (INIS)

    2000-12-01

    In order to dispose of the spent nuclear fuel in a safe manner, SKB plans to site a deep repository and an encapsulation plant with associated canister fabrication and transportation system. After an integrated evaluation of feasibility studies and other material, SKB will proceed with investigations of the rock and studies regarding establishment of the deep disposal system in the municipality of Oskarshamn or in Northern Uppland. The plans also include further study of the prospects for a deep repository in the municipality of Nykoeping. In the municipality of Oskarshamn, SKB plans further studies of a siting of the deep repository at Simpevarp. There SKB wants to initiate site investigations with test drilling. For the encapsulation plant, SKB wants to continue studying a siting at CLAB. In Northern Uppland, SKB plans to study two siting alternatives for the deep repository. One is Forsmark in the municipality of Oesthammar, where SKB wants to initiate a site investigation with test drilling. The other is Tierp north of Skutskaer, where SKB intends to start test drilling in an area north of Tierp. First, however, a suitable drilling area with possible transport solutions needs to be defined. This alternative requires the participation of the municipalities of both Tierp and Aelvkarleby. A siting of the encapsulation plant in Northern Uppland will also be studied. For the municipality of Nykoeping, SKB plans to conduct a new safety assessment for the Fjaellveden area, based on data from previous investigations as well as additional studies of how a deep repository could be arranged. SKB will thereby gather data from yet another geographic and geological region beyond those that are prioritized. No test drilling is planned in Nykoeping. The goal of the site investigation phase is to obtain all permits needed to build the planned facilities. It will take an estimated 7 - 8 years to assemble the requisite supporting material, carry out consultations, compile siting

  16. Inulin in Medicinal Plants (IV) : Reversed-Phase High-Performance Liquid Chromatography of Inulin after Acetylation : Molecular-Weight Distribution of Inulin in Medicinal Plants

    OpenAIRE

    三野, 芳紀; 筒井, 聡美; 太田, 長世; YOSHIKI, MINO; SATOMI, TSUTSUI; NAGAYO, OTA; 大阪薬科大学; 大阪薬科大学; 大阪薬科大学; Osaka College of Pharmacy; Osaka College of Pharmacy; Osaka College of Pharmacy

    1985-01-01

    Reversed-phase high-performance liquid chromatography coupled with pre-acetylation enabled acculate molecular-weight assay of inulin in medicinal plants to be conducted. The results clearly showed that the molecular-weight distribution of inulin varied depending on the stage of growth: Small molecular weight inulin polymers were detected in large quantity in the earlier growth stage whereas large molecular weight inulin polymers at the flowering and post flowering period.

  17. Numerical-experimental investigation of load paths in DP800 dual phase steel during Nakajima test

    Science.gov (United States)

    Bergs, Thomas; Nick, Matthias; Feuerhack, Andreas; Trauth, Daniel; Klocke, Fritz

    2018-05-01

    Fuel efficiency requirements demand lightweight construction of vehicle body parts. The usage of advanced high strength steels permits a reduction of sheet thickness while still maintaining the overall strength required for crash safety. However, damage, internal defects (voids, inclusions, micro fractures), microstructural defects (varying grain size distribution, precipitates on grain boundaries, anisotropy) and surface defects (micro fractures, grooves) act as a concentration point for stress and consequently as an initiation point for failure both during deep drawing and in service. Considering damage evolution in the design of car body deep drawing processes allows for a further reduction in material usage and therefore body weight. Preliminary research has shown that a modification of load paths in forming processes can help mitigate the effects of damage on the material. This paper investigates the load paths in Nakajima tests of a DP800 dual phase steel to research damage in deep drawing processes. Investigation is done via a finite element model using experimentally validated material data for a DP800 dual phase steel. Numerical simulation allows for the investigation of load paths with respect to stress states, strain rates and temperature evolution, which cannot be easily observed in physical experiments. Stress triaxiality and the Lode parameter are used to describe the stress states. Their evolution during the Nakajima tests serves as an indicator for damage evolution. The large variety of sheet metal forming specific load paths in Nakajima tests allows a comprehensive evaluation of damage for deep drawing. The results of the numerical simulation conducted in this project and further physical experiments will later be used to calibrate a damage model for simulation of deep drawing processes.

  18. Critical role of bioanalytical strategies in investigation of clinical PK observations, a Phase I case study

    Science.gov (United States)

    Peng, Kun; Xu, Keyang; Liu, Luna; Hendricks, Robert; Delarosa, Reginald; Erickson, Rich; Budha, Nageshwar; Leabman, Maya; Song, An; Kaur, Surinder; Fischer, Saloumeh K

    2014-01-01

    RG7652 is a human immunoglobulin 1 (IgG1) monoclonal antibody (mAb) targeting proprotein convertase subtilisin/kexin type 9 (PCSK9) and is designed for the treatment of hypercholesterolemia. A target-binding enzyme-linked immunosorbent assay (ELISA) was developed to measure RG7652 levels in human serum in a Phase I study. Although target-binding assay formats are generally used to quantify free therapeutic, the actual therapeutic species being measured are affected by assay conditions, such as sample dilution and incubation time, and levels of soluble target in the samples. Therefore, in the presence of high concentrations of circulating target, the choice of reagents and assay conditions can have a significant effect on the observed pharmacokinetic (PK) profiles. Phase I RG7652 PK analysis using the ELISA data resulted in a nonlinear dose normalized exposure. An investigation was conducted to characterize the ELISA to determine whether the assay format and reagents may have contributed to the PK observation. In addition, to confirm the ELISA results, a second orthogonal method, liquid chromatography tandem mass spectrometry (LC-MS/MS) using a signature peptide as surrogate, was developed and implemented. A subset of PK samples, randomly selected from half of the subjects in the 6 single ascending dose (SAD) cohorts in the Phase I clinical study, was analyzed with the LC-MS/MS assay, and the data were found to be comparable to the ELISA data. This paper illustrates the importance of reagent characterization, as well as the benefits of using an orthogonal approach to eliminate bioanalytical contributions when encountering unexpected observations. PMID:25484037

  19. A nanoindentation investigation of local strain rate sensitivity in dual-phase Ti alloys

    Energy Technology Data Exchange (ETDEWEB)

    Jun, Tea-Sung, E-mail: t.jun@imperial.ac.uk [Department of Materials, Royal School of Mines, Imperial College London, London, SW7 2AZ (United Kingdom); Armstrong, David E.J. [Department of Materials, University of Oxford, Parks Road, Oxford, OX1 3PH (United Kingdom); Britton, T. Benjamin [Department of Materials, Royal School of Mines, Imperial College London, London, SW7 2AZ (United Kingdom)

    2016-07-05

    Using nanoindentation we have investigated the local strain rate sensitivity in dual-phase Ti alloys, Ti–6Al–2Sn–4Zr-xMo (x = 2 and 6), as strain rate sensitivity could be a potential factor causing cold dwell fatigue. Electron backscatter diffraction (EBSD) was used to select hard and soft grain orientations within each of the alloys. Nanoindentation based tests using the continuous stiffness measurement (CSM) method were performed with variable strain rates, on the order of 10{sup −1} to 10{sup −3}s{sup −1}. Local strain rate sensitivity is determined using a power law linking equivalent flow stress and equivalent plastic strain rate. Analysis of residual impressions using both a scanning electron microscope (SEM) and a focused ion beam (FIB) reveals local deformation around the indents and shows that nanoindentation tested structures containing both α and β phases within individual colonies. This indicates that the indentation results are derived from averaged α/β properties. The results show that a trend of local rate sensitivity in Ti6242 and Ti6246 is strikingly different; as similar rate sensitivities are found in Ti6246 regardless of grain orientation, whilst a grain orientation dependence is observed in Ti6242. These findings are important for understanding dwell fatigue deformation modes, and the methodology demonstrated can be used for screening new alloy designs and microstructures. - Highlights: • Nanoindentation-based CSM tests were performed on dual-phase Ti alloys. • EBSD was effectively used to select target grains within isolated morphologies. • A trend of local rate sensitivity in Ti6242 and Ti6246 is strikingly different. • A significant grain orientation dependent rate sensitivity is observed in Ti6242. • Similar rate sensitivities are found in Ti6246 regardless of grain orientation.

  20. Thermoplastic Micromodel Investigation of Two-Phase Flows in a Fractured Porous Medium

    Directory of Open Access Journals (Sweden)

    Shao-Yiu Hsu

    2017-01-01

    Full Text Available In the past few years, micromodels have become a useful tool for visualizing flow phenomena in porous media with pore structures, e.g., the multifluid dynamics in soils or rocks with fractures in natural geomaterials. Micromodels fabricated using glass or silicon substrates incur high material cost; in particular, the microfabrication-facility cost for making a glass or silicon-based micromold is usually high. This may be an obstacle for researchers investigating the two-phase-flow behavior of porous media. A rigid thermoplastic material is a preferable polymer material for microfluidic models because of its high resistance to infiltration and deformation. In this study, cyclic olefin copolymer (COC was selected as the substrate for the micromodel because of its excellent chemical, optical, and mechanical properties. A delicate micromodel with a complex pore geometry that represents a two-dimensional (2D cross-section profile of a fractured rock in a natural oil or groundwater reservoir was developed for two-phase-flow experiments. Using an optical visualization system, we visualized the flow behavior in the micromodel during the processes of imbibition and drainage. The results show that the flow resistance in the main channel (fracture with a large radius was higher than that in the surrounding area with small pore channels when the injection or extraction rates were low. When we increased the flow rates, the extraction efficiency of the water and oil in the mainstream channel (fracture did not increase monotonically because of the complex two-phase-flow dynamics. These findings provide a new mechanism of residual trapping in porous media.

  1. Gas-Phase Thermal Tautomerization of Imidazole-Acetic Acid: Theoretical and Computational Investigations

    Directory of Open Access Journals (Sweden)

    Saadullah G. Aziz

    2015-11-01

    Full Text Available The gas-phase thermal tautomerization reaction between imidazole-4-acetic (I and imidazole-5-acetic (II acids was monitored using the traditional hybrid functional (B3LYP and the long-range corrected functionals (CAM-B3LYP and ωB97XD with 6-311++G** and aug-cc-pvdz basis sets. The roles of the long-range and dispersion corrections on their geometrical parameters, thermodynamic functions, kinetics, dipole moments, Highest Occupied Molecular Orbital–Lowest Unoccupied Molecular Orbital (HOMO–LUMO energy gaps and total hyperpolarizability were investigated. All tested levels of theory predicted the preference of I over II by 0.750–0.877 kcal/mol. The origin of predilection of I is assigned to the H-bonding interaction (nN8→σ*O14–H15. This interaction stabilized I by 15.07 kcal/mol. The gas-phase interconversion between the two tautomers assumed a 1,2-proton shift mechanism, with two transition states (TS, TS1 and TS2, having energy barriers of 47.67–49.92 and 49.55–52.69 kcal/mol, respectively, and an sp3-type intermediate. A water-assisted 1,3-proton shift route brought the barrier height down to less than 20 kcal/mol in gas-phase and less than 12 kcal/mol in solution. The relatively high values of total hyperpolarizability of I compared to II were interpreted and discussed.

  2. Investigation of the effect of different parameters on the phase inversion temperature O/W nanoemulsions

    Directory of Open Access Journals (Sweden)

    D. Kaviani

    2016-01-01

    Full Text Available Objective(s: Nanoemulsions are a kind of emulsions that can be transparent, translucent (size range 50-200 nm or “milky” (up to 500 nm. Nanoemulsions are adequatly effective for transfer of active component through skin which facilitate the entrance of the active component . The transparent nature of the system and lack of the thickener and fluidity are among advantages of nanoemulsion. Materials and Methods: In this study, a nanoemulsion of lemon oil in water was prepared by the phase inversion temperature (PIT emulsification method in which the tween 40 was used as surfactant. The effect of concentration of NaCl in aqueous phase, pH and weight percent of surfactant and aqueous on the PIT and droplet size were investigated. Results: The results showed that with increasing of concentration of NaCl from 0.05 M to 1 M, PIT decrease from 72 to 50. The average droplet sizes, for 0.1, 0.5 and 1 M of NaCl in 25 ºC are 497.3, 308.1 and 189.9 nm, respectively and the polydispersity indexes are 0.348, 0.334 and 0.307, respectively. Conclusion: Considering the characteristics of nanoemulsions such as being transparent, endurance of solution and droplet size can provide suitable reaction environment for polymerization process used in making hygienic and medical materials.

  3. Online analytical investigations on solvent-, temperature- and water vapour-induced phase transformations of citric acid

    Energy Technology Data Exchange (ETDEWEB)

    Helmdach, L.; Ulrich, J. [Martin-Luther-Universitaet Halle-Wittenberg, Zentrum fuer Ingenieurwissenschaft, Verfahrenstechnik/TVT, Halle (Saale) (Germany); Feth, M.P. [Sanofi-Aventis Deutschland GmbH, Chemical and Process Development Frankfurt Chemistry, Frankfurt (Germany)

    2012-09-15

    It was demonstrated exemplarily for the crystallization of citric acid that the usage of an ultrasound device as well as Raman spectroscopy enables the inline measurement and the control of phase transitions. The influence of different solvent compositions (water and ethanol-water) on the crystallization of citric acid was investigated. By increasing the ethanol content the transformation point was shifted towards higher temperatures. In addition, a strong impact on the nucleation point as well as on the crystal habit was detected in ethanol-water mixtures. The results lead to the assumption that a citric acid solvate exists, which is, however, highly unstable upon isolation from mother liquor and converts fast into the known anhydrate or monohydrate forms of citric acid. The presence of such a solvate, however, could not be proven during this study. Furthermore, factors such as temperature and humidity which might influence the phase transition of the solid product were analyzed by Hotstage-Raman Spectroscopy and Water Vapor Sorption Gravimetry-Dispersive Raman Spectroscopy. Both, temperature as well as humidity show a strong influence on the behaviour of CAM. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  4. Investigation of phase transformations in ductile cast iron of differential scanning calorimetry

    International Nuclear Information System (INIS)

    Przeliorz, R; Piatkowski, J

    2011-01-01

    The effect of heating rate on phase transformations to austenite range in ductile cast iron of the EN-GJS-450-10 grade was investigated. For studies of phase transformations, the technique of differential scanning calorimetry (DSC) was used. Micro structure was examined by optical microscopy. The calorimetric examinations have proved that on heating three transformations occur in this grade of ductile iron, viz. magnetic transformation at the Curie temperature, pearlite→austenite transformation and ferrite→austenite transformation. An increase in the heating rate shifts the pearlite→austenite and ferrite→austenite transformations to higher temperature range. At the heating rate of 5 and 15 deg. C min -1 , local extrema have been observed to occur: for pearlite→austenite transformation at 784 deg. C and 795 deg. C, respectively, and for ferrite+ graphite →austenite transformation at 805 deg. C and 821 deg. C, respectively. The Curie temperature of magnetic transformation was extrapolated to a value of 740 deg. C. Each transformation is related with a specific thermal effect. The highest value of enthalpy is accompanying the ferrite→austenite transformation, the lowest occurs in the case of pearlite→austenite transformation.

  5. Investigation of phase stability and oxide ion performance in new perovskite-type bismuth vanadate

    International Nuclear Information System (INIS)

    Al-Alas, Ahlam; Beg, Saba; Al-Areqi, Niyazi A.S.

    2012-01-01

    Samples of the BICDVOX system, formulated as Bi 4 Cd x V 2−x O 11−(3x/2)−δ in the Cd substitution range 0 ≤ x ≤ 0.25 were synthesized using the standard solid state reaction.The correlation between phase stability and oxide ion performance were investigated by variable temperature XRPD, DSC and AC impedance spectroscopy. The substitution of V 5+ by Cd 2+ exhibited different phase transitions upon varying composition. For compositions with x ≤ 0.05, two successive transitions; α↔β↔γ are evident, while the β↔γ transition exists in the composition range 0.05 4+ → V 5+ re–oxidation results in increased defect trapping effects in the system at higher temperatures. -- Highlights: ► γ-Stabilized BICDVOX at lower dopant concentrations. ► Good oxide-ion conductivity at lower temperatures. ► High temperature-vanadium reduction with lower dopant concentrations.

  6. An investigation on two-phase mixture discharges: the effects of macroparticle sizes

    Energy Technology Data Exchange (ETDEWEB)

    Deng Heming; He Zhenghao; Xu Yuhang; Ma Jun; Liu Junxiang; Guo Runkai, E-mail: denghem@gmail.co [School of Environmental Science and Engineering, Huazhong University of Science and Technology, Hubei province Wuhan 430074 (China)

    2010-06-30

    A two-phase mixture (TPM) is a mixture of gas and macroparticles of high concentration, and there has been significant interest in many technical applications and natural phenomena concerning two-phase mixture discharges (TPMDs), but until now there has been no widely accepted analysis for the propagation of discharges in TPMs. In this paper, 21 kinds of different dielectric materials are used to investigate the effects on TPMD. The diameters of macroparticles in 21 kinds of TPMs are measured by microscope, laser particle size analyzer, etc, and the volume fractions are measured by a video camera and particle image velocimetry system. Based on a direct comparison of the breakdown voltages and the percentages of the discharge path in TPMs with those in air, this work reveals that whether TPMs promote the discharge development or not depends mainly on the macroparticle sizes. These macroparticles in TPMs distort the electric field, interact with ions, electrons or photons, and produce corresponding enhancements or decreases in ionization and excitation as the streamer front encounters them, but the details of alterations on the discharge development are highly correlated with the macroparticle sizes.

  7. Phase II drugs currently being investigated for the treatment of hypogonadism.

    Science.gov (United States)

    Udedibia, Emeka; Kaminetsky, Jed

    2014-12-01

    Hypogonadism is the most common endocrine disorder, which affects men of all age groups. Recent shifts in public awareness, increased screening and recognition of symptoms and updated diagnostic criteria have led to an increase in men diagnosed as hypogonadal, including middle-aged and older men who previously would have been considered eugonadal. The increase in testosterone replacement therapy (TRT) has paralleled an increase in advancements of treatment options. Although current therapies are highly efficacious for many men, there remains a need for newer therapies that are more cost-effective, preserve ease of use and administration, mitigate undesirable effects and closely mimic physiological levels of testosterone. In this review, the authors discuss current TRTs and therapies in development for the treatment of hypogonadism. The focus is on therapies under Phase II investigation or those who have recently completed Phase II study. With several new therapies in development, the authors expect advancements in achieving treatment benchmarks that meet the needs of the individual symptomatic hypogonadal male. Increased public awareness of hypogonadism and TRT has led to a welcomed expansion in the choice of TRT options. These include new delivery systems, formulations, routes of administration and non-testosterone modalities.

  8. Investigation of phase synchronization of interictal EEG in right temporal lobe epilepsy

    Science.gov (United States)

    Yu, Haitao; Cai, Lihui; Wu, Xinyu; Song, Zhenxi; Wang, Jiang; Xia, Zijie; Liu, Jing; Cao, Yibin

    2018-02-01

    Epilepsy is commonly associated with abnormally synchronous activity of neurons located in epileptogenic zones. In this study, we investigated the synchronization characteristic of right temporal lobe epilepsy (RTLE). Multichannel electroencephalography (EEG) data were recorded from the RTLE patients during interictal period and normal controls. Power spectral density was first used to analyze the EEG power for two groups of subjects. It was found that the power of epileptics is increased in the whole brain compared with that of the control. We calculated phase lag index (PLI) to measure the phase synchronization between each pair of EEG signals. A higher degree of synchronization was observed in the epileptics especially between distant channels. In particular, the regional synchronization degree was negatively correlated with power spectral density and the correlation was weaker for epileptics. Moreover, the synchronization degree decayed with the increase of relative distance of channels for both the epilepsy and control, but the dependence was weakened in the former. The obtained results may provide new insights into the generation mechanism of epilepsy.

  9. Optical investigation of gas-phase KCl/KOH sulfation in post flame conditions

    DEFF Research Database (Denmark)

    Weng, Wubin; chen, Shuang; Wu, Hao

    2018-01-01

    A counter-flow reactor setup was designed to investigate the gas-phase sulfation and homogeneous nucleation of potassium salts. Gaseous KOH and KCl were introduced into the post-flame zone of a laminar flat flame. The hot flame products mixed in the counter-flow with cold N2, with or without....... Depending on the potassium speciation in the inlet and the presence of SO2, they consisted of K2SO4, KCl, or K2CO3, respectively. The experiments showed that KOH was sulphated more readily than KCl, resulting in larger quantities of aerosols. The sulfation process in the counter-flow setup was simulated...... using a chemical kinetic model including a detailed subset for the Cl/S/K chemistry. Similar to the experimental results, much more potassium sulfate was predicted when seeding KOH compared to seeding KCl. For both KOH and KCl, sulfation was predicted to occur primarily through the reactions among...

  10. Investigation of A-3 adsorbent-ditolylmethane two-phase system

    International Nuclear Information System (INIS)

    Ermakov, V.A.; Benderskaya, O.S.

    1988-01-01

    Compatibility of A-3 adsorbent, produced on the basis of palygoskite clay, with organic coolant of nuclear reactors-ditolylmethane (DTM)- and the possibility to use the given adsorbent for DTM purification from surfactant impurities are investigated. Compatibility of the adsorbent with DTM was evaluated by the concentration of its constituents in liquid phase. Sufactant adsorption was observed by the change in acid number of coolant, optical density at λ=396 nm and adsorbate mass in the adsorbent. From spent adsorbent the coolant was washed out by n-heptane, and the adsorbate - by methylene chloride, othanol and water in succession. On the basis of the results obtained the conclusion is made that A3 possesses a high chemical stability in DTM medium, i.e. it is compatible with DTM and can be used for its purification from surfactant impurities sorbed on heat-transferring surface

  11. UPS and DFT investigation of the electronic structure of gas-phase trimesic acid

    Energy Technology Data Exchange (ETDEWEB)

    Reisberg, L., E-mail: rebban@ut.ee [Institute of Physics, University of Tartu, W. Oswaldi 1, EE-50411 Tartu (Estonia); Pärna, R. [Institute of Physics, University of Tartu, W. Oswaldi 1, EE-50411 Tartu (Estonia); MAX IV Laboratory, Lund University, Fotongatan 2, 225 94 Lund (Sweden); Kikas, A.; Kuusik, I.; Kisand, V. [Institute of Physics, University of Tartu, W. Oswaldi 1, EE-50411 Tartu (Estonia); Hirsimäki, M.; Valden, M. [Surface Science Laboratory, Optoelectronics Research Centre, Tampere University of Technology, FIN-33101 Tampere (Finland); Nõmmiste, E. [Institute of Physics, University of Tartu, W. Oswaldi 1, EE-50411 Tartu (Estonia)

    2016-11-15

    Highlights: • In the current study outer valence band electronic structure of benzene-1,3,5-tricarboxylic acid was interpreted. • Experimental and calculated trimesic acid (TMA) spectrum were compared to ones of benzene and benzoic acid. • It is shown that similarities between MO energies and shapes for benzene and TMA exists. • Addition of carboxyl groups to the benzene ring clearly correlates with increasing binding energy of HOMO. - Abstract: Benzene-1,3,5-tricarboxylic acid (trimesic acid, TMA) molecules in gas-phase have been investigated by using valence band photoemission. The photoelectron spectrum in the binding energy region from 9 to 22 eV is interpreted by using density functional theory calculations. The electronic structure of TMA is compared with benzene and benzoic acid in order to demonstrate changes in molecular orbital energies induced by addition of carboxyl groups to benzene ring.

  12. Numerical Investigation of Deviation of Phase Change Characteristics of Horizontal and Vertical Flat Heat Pipe Configurations

    Directory of Open Access Journals (Sweden)

    Rakesh Hari

    2015-12-01

    Full Text Available The flow characteristics in the porous wick of a flat heat pipe subjected to boiling and condensation are analysed here using two-phase mixture model. Steady laminar boundary layer flow in the capillary wick structure is considered for both vertical and horizontal orientations. The governing boundary layer partial differential equations are simplified using similarity transformation. The transformed equations are then solved numerically by using shooting iterative technique. Investigation was carried out for the effects of the involved parameters such as saturation and temperature across the boundary layer. The behaviour of non-dimensional numbers due to the orientation of the heat pipe is also discussed. The study confirms that orientation plays a significant role in flow and temperature field.

  13. Detailed investigation of proposed gas-phase syntheses of ammonia in dense interstellar clouds

    International Nuclear Information System (INIS)

    Herbst, E.; Defrees, D.J.; Mclean, A.D.; Molecular Research Institute, Palo Alto, CA; IBM Almaden Research Center, San Jose, CA)

    1987-01-01

    The initial reactions of the Herbst and Klemperer (1973) and the Dalgarno (1974) schemes (I and II, respectively) for the gas-phase synthesis of ammonia in dense interstellar clouds were investigated. The rate of the slightly endothermic reaction between N(+) and H2 to yield NH(+) and H (scheme I) under interstellar conditions was reinvestigated under thermal and nonthermal conditions based on laboratory data. It was found that the relative importance of this reaction in synthesizing ammonia is determined by how the laboratory data at low temperature are interpreted. On the other hand, the exothermic reaction between N and H3(+) to form NH2(+) + H (scheme II) was calculated to possess significant activation energy and, therefore, to have a negligible rate coefficient under interstellar conditions. Consequently, this reaction cannot take place appreciably in interstellar clouds. 41 references

  14. Plutonium(IV) precipitates formed in alkaline media in the presence of various anions

    Energy Technology Data Exchange (ETDEWEB)

    Krot, N.N.; Shilov, V.P.; Yusov, A.B.; Tananaev, I.G.; Grigoriev, M.S.; Garnov, A.Yu.; Perminov, V.P.; Astafurova, L.N.

    1998-09-01

    The tendency of Pu(IV) to hydrolyze and form true solutions, colloid solutions, or insoluble precipitates has been known since the Manhattan Project. Since then, specific studies have been performed to examine in detail the equilibria of Pu(IV) hydrolytic reactions in various media. Great attention also has been paid to the preparation, structure, and properties of Pu(IV) polymers or colloids. These compounds found an important application in sol-gel technology for the preparation of nuclear fuel materials. A most important result of these works was the conclusion that Pu(IV) hydroxide, after some aging, consists of very small PuO{sub 2} crystallites and should therefore be considered to be Pu(IV) hydrous oxide. However, studies of the properties and behavior of solid Pu(IV) hydroxide in complex heterogeneous systems are rare. The primary goal of this investigation was to obtain data on the composition and properties of Pu(IV) hydrous oxide or other compounds formed in alkaline media under different conditions. Such information is important to understand Pu(IV) behavior and the forms of its existence in the Hanford Site alkaline tank waste sludge. This knowledge then may be applied in assessing plutonium criticality hazards in the storage, retrieval, and treatment of Hanford Site tank wastes as well as in understanding its contribution to the transuranic waste inventory (threshold at 100 nCi/g or about 5 {times} 10{sup {minus}6} M) of the separate solution and solid phases.

  15. Plutonium(IV) precipitates formed in alkaline media in the presence of various anions

    International Nuclear Information System (INIS)

    Krot, N.N.; Shilov, V.P.; Yusov, A.B.; Tananaev, I.G.; Grigoriev, M.S.; Garnov, A.Yu.; Perminov, V.P.; Astafurova, L.N.

    1998-09-01

    The tendency of Pu(IV) to hydrolyze and form true solutions, colloid solutions, or insoluble precipitates has been known since the Manhattan Project. Since then, specific studies have been performed to examine in detail the equilibria of Pu(IV) hydrolytic reactions in various media. Great attention also has been paid to the preparation, structure, and properties of Pu(IV) polymers or colloids. These compounds found an important application in sol-gel technology for the preparation of nuclear fuel materials. A most important result of these works was the conclusion that Pu(IV) hydroxide, after some aging, consists of very small PuO 2 crystallites and should therefore be considered to be Pu(IV) hydrous oxide. However, studies of the properties and behavior of solid Pu(IV) hydroxide in complex heterogeneous systems are rare. The primary goal of this investigation was to obtain data on the composition and properties of Pu(IV) hydrous oxide or other compounds formed in alkaline media under different conditions. Such information is important to understand Pu(IV) behavior and the forms of its existence in the Hanford Site alkaline tank waste sludge. This knowledge then may be applied in assessing plutonium criticality hazards in the storage, retrieval, and treatment of Hanford Site tank wastes as well as in understanding its contribution to the transuranic waste inventory (threshold at 100 nCi/g or about 5 x 10 -6 M) of the separate solution and solid phases

  16. Investigation of the system ThO2-NpO2-P2O5. Solid solutions of thorium-neptunium (IV) phosphate-diphosphate

    International Nuclear Information System (INIS)

    Dacheux, N.; Thomas, A.C.; Brandel, V.; Genet, M.

    1998-01-01

    Considering that phosphate matrices could be potential candidates for the immobilization of actinides or for the final disposal of the excess plutonium from dismantled nuclear weapons, the chemistry of thorium phosphates has been re-examined. In the ThO 2 -P 2 O 5 system, the thorium phosphate-diphosphate Th 4 (PO 4 ) 4 P 2 O 7 (TPD) can be synthesized by wet and dry chemical processes. The substitution of thorium by other tetravalent actinides like uranium or plutonium can be obtained for 0 4-x Np x (PO 4 ) 4 P 2 O 7 (TNPD) with 0 4+ by Np 4+ in the TPD structure is evaluated to 2.08 (which corresponds to about 52 mol% of thorium replaced by neptunium (IV)). The field of existence of solid solutions Th 4-x U -x Np -x Pu U x U Np x Np Pu x Pu (PO 4 )4P 2 O 7 has been calculated. These solid solutions should be synthesized for 5x U +7x Np +9x Pu ≤15. In the NpO 2 -P 2 O 5 system, the unit cell parameters of Np 2 O(PO 4 ) 2 were refined by analogy with U 2 O(PO 4 ) 2 which crystallographic data have been published recently. For Np 2 O(PO 4 ) 2 the unit cell is orthorhombic with the following cell parameters: a=7.033(2)A, b=9.024(3)A, c=12.587(6)A and V=799(1)A 3 . The unit cell parameter obtained for α-NpP 2 O 7 (a=8.586(1)A) is in good agreement with those already reported in literature. (orig.)

  17. An Investigation of Rotorcraft Stability-Phase Margin Requirements in Hover

    Science.gov (United States)

    Blanken, Chris L.; Lusardi, Jeff A.; Ivler, Christina M.; Tischler, Mark B.; Hoefinger, Marc T.; Decker, William A.; Malpica, Carlos A.; Berger, Tom; Tucker, George E.

    2009-01-01

    A cooperative study was performed to investigate the handling quality effects from reduced flight control system stability margins, and the trade-offs with higher disturbance rejection bandwidth (DRB). The piloted simulation study, perform on the NASA-Ames Vertical Motion Simulator, included three classes of rotorcraft in four configurations: a utility-class helicopter; a medium-lift helicopter evaluated with and without an external slung load; and a large (heavy-lift) civil tiltrotor aircraft. This large aircraft also allowed an initial assessment of ADS-33 handling quality requirements for an aircraft of this size. Ten experimental test pilots representing the U.S. Army, Marine Corps, NASA, rotorcraft industry, and the German Aerospace Center (DLR), evaluated the four aircraft configurations, for a range of flight control stability-margins and turbulence levels, while primarily performing the ADS-33 Hover and Lateral Reposition MTEs. Pilot comments and aircraft-task performance data were analyzed. The preliminary stability margin results suggest higher DRB and less phase margin cases are preferred as the aircraft increases in size. Extra care will need to be taken to assess the influence of variability when nominal flight control gains start with reduced margins. Phase margins as low as 20-23 degrees resulted in low disturbance-response damping ratios, objectionable oscillations, PIO tendencies, and a perception of an incipient handling qualities cliff. Pilot comments on the disturbance response of the aircraft correlated well to the DRB guidelines provided in the ADS-33 Test Guide. The A D-3S3 mid-term response-to-control damping ratio metrics can be measured and applied to the disturbance-response damping ratio. An initial assessment of LCTR yaw bandwidth shows the current Level 1 boundary needs to be relaxed to help account for a large pilot off-set from the c.g. Future efforts should continue to investigate the applicability/refinement of the current ADS-33

  18. Transdermal granisetron versus palonosetron for prevention of chemotherapy-induced nausea and vomiting following moderately emetogenic chemotherapy: a multicenter, randomized, open-label, cross-over, active-controlled, and phase IV study.

    Science.gov (United States)

    Seol, Young Mi; Kim, Hyo Jeong; Choi, Young Jin; Lee, Eun Mi; Kim, Yang Soo; Oh, Sung Yong; Koh, Su Jin; Baek, Jin Ho; Lee, Won Sik; Joo, Young Don; Lee, Hyun Gi; Yun, Eun Young; Chung, Joo Seop

    2016-02-01

    Palonosetron is the second-generation 5-hydroxytryptamine 3 receptor antagonist (5-HT3RA) that has shown better efficacy than the first-generation 5-HT3RA for prevention of chemotherapy-induced nausea and vomiting (CINV) in patients receiving moderately emetogenic chemotherapy (MEC). Granisetron transdermal delivery system (GTDS), a novel transdermal formulation, was developed to deliver granisetron continuously over 7 days. This study compared the efficacy and tolerability of the GTDS to palonosetron for the control of CINV following MEC. A total of 196 patients were randomized to GP or PG group. In this multicenter, randomized, open-label, cross-over, active-controlled, Phase IV study, GP group was assigned to receive transdermal granisetron (one GTDS patch, 7 days) in the first chemotherapy cycle, palonosetron (iv 0.25 mg/day, 1 days) in the second chemotherapy cycle before receiving MEC, and PG group was assigned to receive palonosetron in the first cycle and GTDS in the second cycle. Primary endpoint was the percentage of chemotherapy cycles achieving complete response (CR; defined as no emetic episodes and no rescue medication use) during the acute phase (0-24 h in post-chemotherapy; non-inferiority comparison with palonosetron). Total 333 cycles (165 in GTDS and 168 in palonosetron) were included in the per protocol analysis. The GTDS cycles showed non-inferiority to palonosetron cycles during the acute phase: CR was achieved by 124 (75.2 %) patients in the GTDS cycles and 134 (79.8 %) patients in the palonosetron cycles (treatment difference, -4.6 %; 95 % confidence interval, -13.6-4.4). There was no significant difference in CR rate during acute phase after the end of the first and second chemotherapy cycle between GP and PG group (p = 0.405, p = 0.074). Patients' satisfaction, assessed using Functional Living Index-Emesis (FLI-E), GTDS cycle were higher than those of palonosetron cycle in GP group (FLI-E score; median 1549.5 in GTDS cycle, median 1670

  19. Investigation of Virtual Digital Human and Robotic Device Technology Merger Complimented by Haptics and Autostereoscopic Displays, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — As expected, the STTR Phase I investigation confirmed that the Digital Virtual Human (DVH) and Robonaut technologies can be merged, and that haptic and...

  20. Safety and efficacy of first-line bevacizumab with chemotherapy in Asian patients with advanced nonsquamous NSCLC: results from the phase IV MO19390 (SAiL) study.

    Science.gov (United States)

    Tsai, Chun-Ming; Au, Joseph Siu-kie; Chang, Gee-Chen; Cheng, Ashley Chi-kin; Zhou, Caicun; Wu, Yi-long

    2011-06-01

    First-line treatment with bevacizumab combined with chemotherapy has been shown to improve outcomes in patients with advanced, nonsquamous non-small cell lung cancer (NSNSCLC) in phase III clinical trials. SAiL (MO19390), an open-label, multicenter, single-arm study, evaluated the safety and efficacy of first-line bevacizumab-based treatment in clinical practice. This report presents the results of a preplanned subanalysis of Asian patients enrolled in SAiL. Patients with untreated, locally advanced, metastatic or recurrent NSNSCLC received bevacizumab 7.5 or 15 mg/kg every 3 weeks plus chemotherapy for up to six cycles, followed by single-agent bevacizumab until disease progression. Eligibility criteria for SAiL permitted enrolment of a broad patient population. The primary end point was safety; secondary end points included time to disease progression and overall survival. The Asian intent-to-treat population comprised 314 of the 2212 patients enrolled in the SAiL trial. In the Asian subanalysis, patients received a median of nine cycles of bevacizumab, and the median follow-up was 16.4 months. The incidence of clinically significant adverse events (grade ≥3) of special interest was relatively low in this population (15.6% overall); proteinuria (7.6%), hypertension (4.8%), and bleeding (2.5%) were the most common. A total of five adverse events related to bevacizumab were reported as grade 5. Disease control rate was 94.1%, median time to disease progression was 8.3 months, and median overall survival was 18.9 months. The safety and efficacy of first-line bevacizumab-based treatment in Asian patients with advanced NSNSCLC is consistent with that demonstrated in phase III studies and in the overall SAiL population. There were no new safety signals.

  1. Exploration of phase transition in ThS under pressure: An ab-initio investigation

    Science.gov (United States)

    Sahoo, B. D.; Mukherjee, D.; Joshi, K. D.; Kaushik, T. C.

    2018-04-01

    The ab-initio total energy calculations have been performed in thorium sulphide (ThS) to explore its high pressure phase stability. Our calculations predict a phase transformation from ambient rocksalt type structure (B1 phase) to a rhombohedral structure (R-3m phase) at ˜ 15 GPa and subsequently R-3m phase transforms to CsCl type structure (B2 phase) at ˜ 45 GPa. The first phase transition has been identified as second order type; whereas, the second transition is of first order type with volume discontinuity of 6.5%. The predicted high pressure R-3m phase is analogous to the experimentally observed hexagonal (distorted fcc) phase (Benedict et al., J. Less-Common Met., 1984) above 20 GPa. Further, using these calculations we have derived the equation of state which has been utilized to determine various physical quantities such as zero pressure equilibrium volume, bulk modulus, and pressure derivative of bulk modulus at ambient conditions.

  2. Phase II Investigation at the Former CCC/USDA Grain Storage Facility in Savannah, Missouri

    Energy Technology Data Exchange (ETDEWEB)

    LaFreniere, Lorraine M. [Argonne National Lab. (ANL), Argonne, IL (United States). Environmental Science Division. Applied Geosciences and Environmental Management Section

    2012-05-01

    contamination potentially associated with a number of former CCC/USDA grain storage facilities in Missouri. The site characterization at Savannah is being conducted on behalf of the CCC/USDA by the Environmental Science Division of Argonne National Laboratory. The investigation is being conducted in phases, so that information obtained and interpretations developed during each incremental stage can be used most effectively to guide subsequent phases of the program. Phase II objectives: Investigate the more detailed characteristics of groundwater flow in the vicinity of the former CCC/USDA facility and the contaminated Morgan and MoDOT private wells; Obtain additional information on the vertical and lateral distribution and concentrations of carbon tetrachloride in groundwater in the vicinity of the former CCC/USDA facility and the contaminated Morgan and MoDOT private wells; Investigate further for possible evidence of carbon tetrachloride in the subsurface (vadose zone) and deeper soils beneath the former CCC/USDA facility, as well as in the vicinity of the contaminated MoDOT private well.

  3. Hydrogeological characterization on surface-based investigation phase in the Mizunami underground research laboratory project, in Japan

    International Nuclear Information System (INIS)

    Saegusa, Hiromitsu; Onoe, Hironori; Takeuchi, Shinji; Takeuchi, Ryuji; Ohyama, Takuya

    2007-01-01

    The Mizunami Underground Research Laboratory (MIU) project is being carried out by Japan Atomic Energy Agency in the Cretaceous Toki granite in the Tono area, central Japan. The MIU project is a purpose-built generic underground research laboratory project that is planned for a broad scientific study of the deep geological environment as a basis of research and development for geological disposal of nuclear wastes. One of the main goals of the MIU project is to establish comprehensive techniques for investigation, analysis, and assessment of the deep geological environment. The MIU project has three overlapping phases: Surface-based Investigation (Phase I), Construction (Phase II) and Operation (Phase III). Hydrogeological investigations using a stepwise process in Phase I have been carried out in order to obtain information on important properties such as, location of water conducting features, hydraulic conductivity and so on. Hydrogeological modeling and groundwater flow simulations in Phase I have been carried out in order to synthesize these investigation results, to evaluate the uncertainty of the hydrogeological model and to identify the main issues for further investigations. Using the stepwise hydrogeological characterization approach and combining the investigation with modeling and simulation, understanding of the hydrogeological environment has been progressively improved. (authors)

  4. Experimental investigations on the cooling of a motorcycle helmet with phase change material (PCM

    Directory of Open Access Journals (Sweden)

    Fok S.C.

    2011-01-01

    Full Text Available The thermal comfort of motorcycle helmet during hot weather is important as it can affect the physiological and psychological condition of the rider. This paper examines the use of phase change material (PCM to cool a motorcycle helmet and presents the experimental investigations on the influences of the simulated solar radiation, wind speed, and heat generation rate on the cooling system. The result shows that the PCM-cooled helmet is able to prolong the thermal comfort period compared to a normal helmet. The findings also indicate that the heat generation from the head is the predominant factor that will affect the PCM melting time. Simulated solar radiation and ram-air due to vehicle motion under adiabatic condition can have very little influences on the PCM melting time. The results suggested that the helmet usage time would be influenced by the amount of heat generated from the head. Some major design considerations based on these findings have been included. Although this investigation focuses on the cooling of a motorcyclist helmet, the findings would also be useful for the development of PCM-cooling systems in other applications.

  5. Flow injection analysis-flame atomic absorption spectrometry system for indirect determination of sulfite after on-line reduction of solid-phase manganese (IV) dioxide reactor.

    Science.gov (United States)

    Zare-Dorabei, Rouholah; Boroun, Shokoufeh; Noroozifar, Meissam

    2018-02-01

    A new and simple flow injection method followed by atomic absorption spectrometry was developed for indirect determination of sulfite. The proposed method is based on the oxidation of sulfite to sulphate ion using solid-phase manganese dioxide (30% W/W suspended on silica gel beads) reactor. MnO 2 will be reduced to Mn(II) by sample injection in to the column under acidic carrier stream of HNO 3 (pH 2) with flow rate of 3.5mLmin -1 at room temperature. Absorption measurement of Mn(II) which is proportional to the concentration of sulfite in the sample was carried out by atomic absorption spectrometry. The calibration curve was linear up to 25mgL -1 with a detection limit (DL) of 0.08mgL -1 for 400µL injection sample volume. The presented method is efficient toward sulfite determination in sugar and water samples with a relative standard deviation (RSD) less than 1.2% and a sampling rate of about 60h -1 . Copyright © 2017 Elsevier B.V. All rights reserved.

  6. Molten corium concrete interaction: investigation of heat transfer in two-phase flow

    International Nuclear Information System (INIS)

    Amizic, Milan

    2014-01-01

    In the context of severe accident research for the second and the third generation of nuclear power plants, there are still open issues concerning some aspects of the concrete cavity ablation during the molten corium - concrete interaction (MCCI). The determination of heat transfer along the interfacial region between the molten corium pool and the ablating basemat concrete is crucial for the assessment of concrete ablation progression and eventually the basemat melt through. For the purpose of experimental investigation of thermal hydraulics inside a liquid pool agitated by gas bubbles, the CLARA project has been launched. The CLARA experiments are performed using simulant materials and they reveal the influence of superficial gas velocity, liquid viscosity and pool geometry on the heat transfer coefficient between the internally heated liquid pool and vertical and horizontal pool walls maintained at uniform temperature. The first test campaign has been conducted with the small pool configuration (50 cm * 25 cm * 25 cm). The tests have been performed with liquids covering a wide range of dynamic viscosity from approximately 1 mPa s to 10000 mPa s and the superficial gas velocity is varied up to 8 cm/s. This thesis comprises a brief description of MCCI phenomenology, literature reviews on the existing heat transfer correlations for two phase flow and the void fraction, a description of CLARA setup, experimental results and their interpretation. The experimental results are compared with existing models and some new models for the assessment of heat transfer coefficient in two-phase flow. (author) [fr

  7. Waste Area Grouping 2 Remedial Investigation Phase 1 Seep Task data report: Contaminant source area assessment

    International Nuclear Information System (INIS)

    Hicks, D.S.

    1996-03-01

    This report presents the findings of the Waste Area Grouping (WAG) 2, Phase 1 Remedial Investigation (RI) Seep Task efforts during 1993 and 1994 at Oak Ridge National Laboratory (ORNL). The results presented here follow results form the first year of sampling, 1992, which are contained in the Phase 1 RI report for WAG 2 (DOE 1995a). The WAG 2 Seep Task efforts focused on contaminants in seeps, tributaries, and main streams within the White Oak Creek (WOC) watershed. This report is designed primarily as a reference for contaminants and a resource for guiding remedial decisions. Additional in-depth assessments of the Seep Task data may provide clearer understandings of contaminant transport from the different source areas in the WOC watershed. WAG 2 consists of WOC and its tributaries downstream of the ORNL main plant area, White Oak Lake, the White Oak Creek Embayment of the Clinch River, and the associated flood plains and subsurface environment. The WOC watershed encompasses ORNL and associated WAGs. WAG 2 acts as an integrator for contaminant releases from the contaminated sites at ORNL and as the conduit transporting contaminants to the Clinch River. The main objectives of the Seep Task were to identify and characterize seeps, tributaries and source areas that are responsible for the contaminant releases to the main streams in WAG 2 and to quantify their input to the total contaminant release from the watershed at White Oak Dam (WOD). Efforts focused on 90 Sr, 3 H, and 137 Cs because these contaminants pose the greatest potential human health risk from water ingestion at WOD. Bimonthly sampling was conducted throughout the WOC watershed beginning in March 1993 and ending in August 1994. Samples were also collected for metals, anions, alkalinity, organics, and other radionuclides

  8. Modeling of Pu(IV) extraction and HNO3 speciation in nuclear fuel reprocessing

    International Nuclear Information System (INIS)

    De-Sio, S.

    2012-01-01

    The PUREX process is a solvent extraction method dedicated to the reprocessing of irradiated nuclear fuel in order to recover pure uranium and plutonium from aqueous solutions of concentrated nitric acid. The tri-n-butylphosphate (TBP) is used as the extractant in the organic phase. The aim of this thesis work was to improve the modeling of liquid-liquid extraction media in nuclear fuel reprocessing. First, Raman and 14 N NMR measurements, coupled with theoretical calculations based on simple solutions theory and BIMSA modeling, were performed in order to get a better understanding of nitric acid dissociation in binary and ternary solutions. Then, Pu(IV) speciation in TBP after extraction from low nitric acid concentrations was investigated by EXAFS and vis-NIR spectroscopies. We were able to show evidence of the extraction of Pu(IV) hydrolyzed species into the organic phase. A new structural study was conducted on An(VI)/TBP and An(IV)/TBP complexes by coupling EXAFS measurements with DFT calculations. Finally, extraction isotherms modeling was performed on the Pu(IV)/HNO 3 /H 2 O/TBP 30%/dodecane system (with Pu at tracer scale) by taking into account deviation from ideal behaviour in both organic and aqueous phases. The best modeling was obtained when considering three plutonium (IV) complexes in the organic phase: Pu(OH) 2 (NO 3 ) 2 (TBP) 2 , Pu(NO 3 ) 4 (TBP) 2 and Pu(NO 3 ) 4 (TBP) 3 . (author) [fr

  9. Investigation of flow dynamics of liquid phase in a pilot-scale trickle bed reactor using radiotracer technique

    International Nuclear Information System (INIS)

    Pant, H.J.; Sharma, V.K.

    2016-01-01

    A radiotracer investigation was carried out to measure residence time distribution (RTD) of liquid phase in a trickle bed reactor (TBR). The main objectives of the investigation were to investigate radial and axial mixing of the liquid phase, and evaluate performance of the liquid distributor/redistributor at different operating conditions. Mean residence times (MRTs), holdups (H) and fraction of flow flowing along different quadrants were estimated. The analysis of the measured RTD curves indicated radial non-uniform distribution of liquid phase across the beds. The overall RTD of the liquid phase, measured at the exit of the reactor was simulated using a multi-parameter axial dispersion with exchange model (ADEM), and model parameters were obtained. The results of model simulations indicated that the TBR behaved as a plug flow reactor at most of the operating conditions used in the investigation. The results of the investigation helped to improve the existing design as well as to design a full-scale industrial TBR for petroleum refining applications. - Highlights: • Residence time distributions of liquid phase were measured in a trickle bed reactor. • Bromine-82 as ammonium bromide was used as a radiotracer. • Mean residence times, holdups and radial distribution of liquid phase were quantified. • Axial dispersion with exchange model was used to simulate the measured data. • The trickle bed reactor behaved as a plug flow reactor.

  10. Concomitant Chemoradiotherapy Using Carboplatin, Tegafur-Uracil and Leucovorin for Stage III and IV Head-and-Neck Cancer: Results of GORTEC Phase II Study

    International Nuclear Information System (INIS)

    Fesneau, Melanie; Pointreau, Yoann; Chapet, Sophie; Martin, Laurent; Pommier, Pascal; Alfonsi, Marc; Laguerre, Brigitte; Feham, Nasreddine; Berger, Christine; Garaud, Pascal; Calais, Gilles

    2010-01-01

    Purpose: Concomitant chemoradiotherapy is the standard treatment of locally advanced, nonresectable, head-and-neck squamous cell carcinoma. However, the optimal chemotherapy regimen is still controversial. The objective of this Phase II study was to evaluate the feasibility and efficacy of a concomitant treatment using tegafur-uracil, leucovorin, carboplatin, and radiotherapy. Methods and Materials: A total of 77 patients with head-and-neck squamous cell carcinoma Stage III and IVA were enrolled between October 2003 and July 2005. Of the 77 patients, 72 were eligible. They were treated with tegafur-uracil (300 mg/m 2 /d) and leucovorin (75 mg/d) from Days 1 to 19 and from Days 29 to 47 and carboplatin (70 mg/m 2 intravenously for 4 consecutive days), in three cycles every 21 days. Conventional radiotherapy was delivered to a total dose of 70 Gy in 35 fractions. Results: With a mean follow-up of 22.8 months, the 3-year locoregional control, overall survival and disease-free survival actuarial rate was 33.1%, 41.9%, and 27.2%, respectively. The compliance of the treatment was correct. The main acute toxicity was mucositis, with 62% Grade 3-4. Three patients (4.2%) died of acute toxicity. The incidence and severity of late toxicity was acceptable, with 32% Grade 3 and no Grade 4 toxicity. Conclusion: The protocol of concomitant chemoradiotherapy using tegafur-uracil, leucovorin, and carboplatin for locally advanced unresectable head-and-neck squamous cell carcinoma is feasible. The compliance was correct. The incidence and severity of the acute and late toxicities were acceptable, but not improved. The efficacy of this regimen seems equivalent to the main protocols of concurrent chemoradiotherapy. It represents a possible alternative for patients without an intravenous catheter.

  11. [Use of itopride in the symptoms of functional dyspepsia in Russia: results of a phase IV prospective open-label multicenter clinical trial].

    Science.gov (United States)

    Kas'ianenko, V I; Denisov, N L; Vasil'ev, Iu V

    2014-01-01

    To evaluate the efficacy and safety of itopride used to treat the symptoms of functional dyspepsia (FD) of the upper gastrointestinal tract. A prospective, open-label, multicenter trial using as a control the placebo response obtained in the previous investigations enrolled 96 adult patients. The diagnosis of FD corresponded to its Rome II criteria. Patients received itopride (Ganaton) oral tablets (50 mg) 3 times daily for 8 weeks. When included into the trial, the patients were orally given itopride (ganaton) tablets (50 mg) thrice daily before meals for 8 weeks. The patients' status was evaluated during (at weeks 4 and 8) and after (at week 12) treatment. Treatment response was assessed using the Global Patient Assessment (GPA) and the Leeds Dyspepsia Questionnaire (LDQ). To evaluate the safety of itopride use, the investigators studied the frequency of adverse events and carried out laboratory tests (renal and liver function tests) and electrocardiography (ECG). The GPA showed that 53.76, 85.71, and 82.22% of the patients achieved a therapeutic effect of itopride at weeks 4, 8, and 12, respectively. The proportion of the patients who achieved the therapeutic effect (86%) at week 8 was higher than the historical placebo controls in the previous studies--45% (86% vs 45%; X2 = 68.868, df = 3; p Itopride is an effective and well-tolerated drug in the treatment of functional dyspepsia in the Russian patients.

  12. [Environmental investigation of ground water contamination at Wright- Patterson Air Force Base, Ohio]. Volume 4, Health and Safety Plan (HSP); Phase 1, Task 4 Field Investigation report: Draft

    Energy Technology Data Exchange (ETDEWEB)

    1991-10-01

    This Health and Safety Plan (HSP) was developed for the Environmental Investigation of Ground-water Contamination Investigation at Wright-Patterson Air Force Base near Dayton, Ohio, based on the projected scope of work for the Phase 1, Task 4 Field Investigation. The HSP describes hazards that may be encountered during the investigation, assesses the hazards, and indicates what type of personal protective equipment is to be used for each task performed. The HSP also addresses the medical monitoring program, decontamination procedures, air monitoring, training, site control, accident prevention, and emergency response.

  13. Results From the Phase III Randomized Trial of Onartuzumab Plus Erlotinib Versus Erlotinib in Previously Treated Stage IIIB or IV Non-Small-Cell Lung Cancer: METLung.

    Science.gov (United States)

    Spigel, David R; Edelman, Martin J; O'Byrne, Kenneth; Paz-Ares, Luis; Mocci, Simonetta; Phan, See; Shames, David S; Smith, Dustin; Yu, Wei; Paton, Virginia E; Mok, Tony

    2017-02-01

    Purpose The phase III OAM4971g study (METLung) examined the efficacy and safety of onartuzumab plus erlotinib in patients with locally advanced or metastatic non-small-cell lung cancer selected by MET immunohistochemistry whose disease had progressed after treatment with a platinum-based chemotherapy regimen. Patients and Methods Patients were randomly assigned at a one-to-one ratio to receive onartuzumab (15 mg/kg intravenously on day 1 of each 21-day cycle) plus daily oral erlotinib 150 mg or intravenous placebo plus daily oral erlotinib 150 mg. The primary end point was overall survival (OS) in the intent-to-treat population. Secondary end points included median progression-free survival, overall response rate, biomarker analysis, and safety. Results A total of 499 patients were enrolled (onartuzumab, n = 250; placebo, n = 249). Median OS was 6.8 versus 9.1 months for onartuzumab versus placebo (stratified hazard ratio [HR], 1.27; 95% CI, 0.98 to 1.65; P = .067), with a greater number of deaths in the onartuzumab arm (130 [52%] v 114 [46%]). Median progression-free survival was 2.7 versus 2.6 months (stratified HR, 0.99; 95% CI, 0.81 to 1.20; P = .92), and overall response rate was 8.4% and 9.6% for onartuzumab versus placebo, respectively. Exploratory analyses using MET fluorescence in situ hybridization status and gene expression showed no benefit for onartuzumab; patients with EGFR mutations showed a trend toward shorter OS with onartuzumab treatment (HR, 4.68; 95% CI, 0.97 to 22.63). Grade 3 to 5 adverse events were reported by 56.0% and 51.2% of patients, with serious AEs in 33.9% and 30.7%, for experimental versus control arms, respectively. Conclusion Onartuzumab plus erlotinib did not improve clinical outcomes, with shorter OS in the onartuzumab arm, compared with erlotinib in patients with MET-positive non-small-cell lung cancer.

  14. Generation IV national program

    International Nuclear Information System (INIS)

    Preville, M.; Sadhankar, R.; Brady, D.

    2007-01-01

    This paper outlines the Generation IV National Program. This program involves evolutionary and innovative design with significantly higher efficiencies (∼50% compared to present ∼30%) - sustainable, economical, safe, reliable and proliferation resistant - for future energy security. The Generation IV Forum (GIF) effectively leverages the resources of the participants to meet these goals. Ten countries signed the GIF Charter in 2001

  15. Phase 1 remedial investigation report for 200-BP-1 operable unit. Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    1993-09-01

    The US Department of Energy (DOE) Hanford Site, in Washington State is organized into numerically designated operational areas including the 100, 200, 300, 400, 600, and 1100 Areas. The US Environmental Protection Agency (EPA), in November 1989 included the 200 Areas of the Hanford Site on the National Priority List (NPL) under the Comprehensive Environmental Response, Compensation and Liability Act of 1980 (CERCLA). Inclusion on the NPL initiated the remedial investigation (RD process for the 200-BP-1 operable unit. These efforts are being addressed through the Hanford Federal Facility Agreement and Consent Order (Ecology et al. 1989) which was negotiated and approved by the DOE, the EPA, and the State of Washington Department of Ecology (Ecology) in May 1989. This agreement, known as the Tri-Party Agreement, governs all CERCLA efforts at Hanford. In March of 1990, the Department of Energy, Richland Operations (DOE-RL) issued a Remedial Investigation/Feasibility Study (RI/FS) work plan (DOE-RL 1990a) for the 200-BP-1 operable unit. The work plan initiated the first phase of site characterization activities associated with the 200-BP-1 operable unit. The purpose of the 200-BP-1 operable unit RI is to gather and develop the necessary information to adequately understand the risks to human health and the environment posed by the site and to support the development and analysis of remedial alternatives during the FS. The RI analysis will, in turn, be used by Tri-Party Agreement signatories to make a risk-management-based selection of remedies for the releases of hazardous substances that have occurred from the 200-BP-1 operable unit.

  16. Phase 1 remedial investigation report for 200-BP-1 operable unit

    International Nuclear Information System (INIS)

    1993-09-01

    The US Department of Energy (DOE) Hanford Site, in Washington State is organized into numerically designated operational areas including the 100, 200, 300, 400, 600, and 1100 Areas. The US Environmental Protection Agency (EPA), in November 1989 included the 200 Areas of the Hanford Site on the National Priority List (NPL) under the Comprehensive Environmental Response, Compensation and Liability Act of 1980 (CERCLA). Inclusion on the NPL initiated the remedial investigation (RD process for the 200-BP-1 operable unit. These efforts are being addressed through the Hanford Federal Facility Agreement and Consent Order (Ecology et al. 1989) which was negotiated and approved by the DOE, the EPA, and the State of Washington Department of Ecology (Ecology) in May 1989. This agreement, known as the Tri-Party Agreement, governs all CERCLA efforts at Hanford. In March of 1990, the Department of Energy, Richland Operations (DOE-RL) issued a Remedial Investigation/Feasibility Study (RI/FS) work plan (DOE-RL 1990a) for the 200-BP-1 operable unit. The work plan initiated the first phase of site characterization activities associated with the 200-BP-1 operable unit. The purpose of the 200-BP-1 operable unit RI is to gather and develop the necessary information to adequately understand the risks to human health and the environment posed by the site and to support the development and analysis of remedial alternatives during the FS. The RI analysis will, in turn, be used by Tri-Party Agreement signatories to make a risk-management-based selection of remedies for the releases of hazardous substances that have occurred from the 200-BP-1 operable unit

  17. Numerical investigation of a perturbed swirling annular two-phase jet

    Energy Technology Data Exchange (ETDEWEB)

    Siamas, George A. [Mechanical Engineering, School of Engineering and Design, Brunel University, Uxbridge UB8 3PH (United Kingdom)], E-mail: siamas@spidernet.com.cy; Jiang, Xi; Wrobel, Luiz C. [Mechanical Engineering, School of Engineering and Design, Brunel University, Uxbridge UB8 3PH (United Kingdom)

    2009-06-15

    A swirling annular gas-liquid two-phase jet flow system has been investigated by solving the compressible, time-dependent, non-dimensional Navier-Stokes equations using highly accurate numerical methods. The mathematical formulation for the flow system is based on an Eulerian approach with mixed-fluid treatment while an adjusted volume of fluid method is utilised to account for the gas compressibility. Surface tension effects are captured by a continuum surface force model. Swirling motion is applied at the inlet while a small helical perturbation is also applied to initiate the instability. Three-dimensional spatial direct numerical simulation has been performed with parallelisation of the code based on domain decomposition. The results show that the flow is characterised by a geometrical recirculation zone adjacent to the nozzle exit and by a central recirculation zone further downstream. Swirl enhances the flow instability and vorticity and promotes liquid dispersion in the cross-streamwise directions. A dynamic precessing vortex core is developed demonstrating that the growth of such a vortex in annular configurations can be initiated even at low swirl numbers, in agreement with experimental findings. Analysis of the averaged results revealed the existence of a geometrical recirculation zone and a swirl induced central recirculation zone in the flow field.

  18. Formation mechanism of gas bubble superlattice in UMo metal fuels: Phase-field modeling investigation

    Energy Technology Data Exchange (ETDEWEB)

    Hu, Shenyang, E-mail: shenyang.hu@pnnl.gov; Burkes, Douglas E.; Lavender, Curt A.; Senor, David J.; Setyawan, Wahyu; Xu, Zhijie

    2016-10-15

    Nano-gas bubble superlattices are often observed in irradiated UMo nuclear fuels. However, the formation mechanism of gas bubble superlattices is not well understood. A number of physical processes may affect the gas bubble nucleation and growth; hence, the morphology of gas bubble microstructures including size and spatial distributions. In this work, a phase-field model integrating a first-passage Monte Carlo method to investigate the formation mechanism of gas bubble superlattices was developed. Six physical processes are taken into account in the model: 1) heterogeneous generation of gas atoms, vacancies, and interstitials informed from atomistic simulations; 2) one-dimensional (1-D) migration of interstitials; 3) irradiation-induced dissolution of gas atoms; 4) recombination between vacancies and interstitials; 5) elastic interaction; and 6) heterogeneous nucleation of gas bubbles. We found that the elastic interaction doesn’t cause the gas bubble alignment, and fast 1-D migration of interstitials along 〈110〉 directions in the body-centered cubic U matrix causes the gas bubble alignment along 〈110〉 directions. It implies that 1-D interstitial migration along [110] direction should be the primary mechanism of a fcc gas bubble superlattice which is observed in bcc UMo alloys. Simulations also show that fission rates, saturated gas concentration, and elastic interaction all affect the morphology of gas bubble microstructures.

  19. Experimental investigation of solidification in metal foam enhanced phase change material

    Science.gov (United States)

    Beyne, W.; Bağci, O.; Huisseune, H.; Canière, H.; Danneels, J.; Daenens, D.; De Paepe, M.

    2017-10-01

    A major challenge for the use of phase change materials (PCMs) in thermal energy storage (TES) is overcoming the low thermal conductivity of PCM’s. The low conductivity gives rise to limited power during charging and discharging TES. Impregnating metal foam with PCM, however, has been found to enhance the heat transfer. On the other hand, the effect of foam parameters such as porosity, pore size and material type has remained unclear. In this paper, the effect of these foam parameters on the solidification time is investigated. Different samples of PCM-impregnated metal foam were experimentally tested and compared to one without metal foam. The samples varied with respect to choice of material, porosity and pore size. They were placed in a rectangular cavity and cooled from one side using a coolant flowing through a cold plate. The other sides of the rectangular cavity were Polymethyl Methacrylate (PM) walls exposed to ambient. The temperature on the exterior walls of the cavity was monitored as well as the coolant flow rate and its temperature. The metal foam inserts reduced the solidification times by at least 25 %. However, the difference between the best performing and worst performing metal foam is about 28 %. This shows a large potential for future research.

  20. Application of 119Sn Moessbauer spectroscopy to investigations of RET2-X2-type phases

    International Nuclear Information System (INIS)

    Goerlich, E.

    1991-01-01

    Moessbauer spectroscopy of 119 Sn is an effective tool to study nuclear hyperfine interactions which in turn are important as a source of information complementary to that supplied by ''classical'' methods. However, particularly when the effects are subtle, experimental conditions as well as data analysis should be handled with care. The attention is devoted primarily to the finite absorber thickness effects. As examples serve our recent results obtained from investigations of ternary tetragonal phases of RET 2 X 2 -type. In EuPd 2 Si 2 mixed valent system 119 Sn was used as probe which detects the influence of Eu-valency change at a distant site of Si. Electrical resistivity measurements in CeNi 2 Sn 2 may indicate a Kondo-type behaviour while Moessbauer effect leads to the conclusion in favour of a magnetically ordered state. The analysis of resonance absorption spectra of CeAg 2 Sn 2 using a full transmission integral indicates the presence of a metallic β-tin in the sample, while data fitting within the thin absorber approximation has lead to the opposite conclusion. Neither in CeNi 2 Sn 2 nor in ErNi 2 Sn 2 the temperature dependence of the recoil free factors alone cannot explain the observed broadening of spectra at low temperatures. (author). 14 refs, 13 figs

  1. Investigating hyperoxic effects in the rat brain using quantitative susceptibility mapping based on MRI phase.

    Science.gov (United States)

    Hsieh, Meng-Chi; Kuo, Li-Wei; Huang, Yun-An; Chen, Jyh-Horng

    2017-02-01

    To test whether susceptibility imaging can detect microvenous oxygen saturation changes, induced by hyperoxia, in the rat brain. A three-dimensional gradient-echo with a flow compensation sequence was used to acquire T2*-weighted images of rat brains during hyperoxia and normoxia. Quantitative susceptibility mapping (QSM) and QSM-based microvenous oxygenation venography were computed from gradient-echo (GRE) phase images and compared between the two conditions. Pulse oxygen saturation (SpO 2 ) in the cortex was examined and compared with venous oxygen saturation (SvO 2 ) estimated by QSM. Oxygen saturation change calculated by a conventional Δ R2* map was also compared with the ΔSvO 2 estimated by QSM. Susceptibilities of five venous and tissue regions were quantified separately by QSM. Venous susceptibility was reduced by nearly 10%, with an SvO 2 shift of 10% during hyperoxia. A hyperoxic effect, confirmed by SpO 2 measurement, resulted in an SvO 2 increase in the cortex. The ΔSvO 2 between hyperoxia and normoxia was consistent with what was estimated by the Δ R2* map in five regions. These findings suggest that a quantitative susceptibility map is a promising technique for SvO 2 measurement. This method may be useful for quantitatively investigating oxygenation-dependent functional MRI studies. Magn Reson Med 77:592-602, 2017. © 2016 International Society for Magnetic Resonance in Medicine. © 2016 International Society for Magnetic Resonance in Medicine.

  2. Experimental investigation of the dissolution of fractures. From early stage instability to phase diagram

    Science.gov (United States)

    Osselin, Florian; Budek, Agnieszka; Cybulski, Olgierd; Kondratiuk, Pawel; Garstecki, Piotr; Szymczak, Piotr

    2016-04-01

    Dissolution of natural rocks is a fundamental geological process and a key part of landscape formation and weathering processes. Moreover, in current hot topics like Carbon Capture and Storage or Enhanced Oil Recovery, mastering dissolution of the host rock is fundamental for the efficiency and the security of the operation. The basic principles of dissolution are well-known and the theory of the reactive infiltration instability has been extensively studied. However, the experimental aspect has proved very challenging because of the strong dependence of the outcome with pore network, chemical composition, flow rate... In this study we are trying to tackle this issue by using a very simple and efficient device consisting of a chip of pure gypsum inserted between two polycarbonate plates and subjected to a constant flow rate of pure water. Thanks to this device, we are able to control all parameters such as flow rate, fracture aperture, roughness of the walls... but also to observe in situ the progression of the dissolution thanks to the transparency of the polycarbonate which is impossible with 3D rocks. We have been using this experimental set-up to explore and investigate all aspects of the dissolution in a fracture, such as initial instability and phase diagram of different dissolution patterns, and to compare it with theory and simulations, yielding very good agreement and interesting feedbacks on the coupling between flow and chemistry in geological media

  3. Phase II drugs under clinical investigation for the treatment of chronic constipation.

    Science.gov (United States)

    Mozaffari, Shilan; Didari, Tina; Nikfar, Shekoufeh; Abdollahi, Mohammad

    2014-11-01

    Chronic constipation (CC) is a common gastrointestinal (GI) motility disorder that significantly impairs the quality of life in affected subjects. As almost half of the patients suffering from CC are not satisfied with currently available medicines, there is a need to develop new molecules with better effectiveness and tolerability. The authors include all experimental and clinical trials (up to Phase II) about new investigational drugs for the treatment of CC. The article identifies nine new agents: mitemcinal, TD-8954, YKP10811, itopride, RM-131, KWA-0711, elobixibat, velusetrag, and naronapride. All nine agents have shown prokinetic effects in different stages of the development. The mechanisms of new developing drugs include: the activation of 5-hydroxytryptamine type-4 (5-HT4), ghrelin and motilin receptors, antagonizing dopamine type-2 (D2) receptors, inhibition of ileal bile acid reabsorption and acetylcholine esterase, as well as water absorption from the GI tract. At this current point in time, new generations of 5-HT4 receptor agonists (velusetrag, noranopride and YKP10811) are hoped to progress, further in the future, due to better efficiency and safety. However, it is not possible to make a concise conclusion at this current time due to a lack of evidence. Further clinical trials with a longer duration and a larger sample size are warranted.

  4. Investigation of two-phase thermosyphon performance filled with modern HFC refrigerants

    Science.gov (United States)

    Gorecki, Grzegorz

    2018-02-01

    Two-phase closed thermosyphons (TPCTs) are widely utilized as heat exchanger elements in waste heat recovery systems and as passive heating/cooling devices. They are popular because of their high thermal conductivity, simple construction and reliability. Previous researches indicate that refrigerants are performing better than typical TPCT working fluids like deionized water or alcohols in the low temperature range. In the present study three HFC (Hydrofluorocarbons) refrigerants were tested: R134a, R404A and R407C. The total length of the investigated TPCT is 550 mm with equal length (245 mm) condenser and evaporator sections. Its outer diameter is 22 mm with 1 mm wall thickness. The evaporator section was heated by hot water with varying inlet temperature by 5 K step in the range of 288 K - 323 K. The condenser was cooled by cold water with inlet temperature kept at a constant value of 283 K. It was found that using R134a and R404A as working fluids heat transfer rates are the highest. For both refrigerants 10% is optimal filling ratio. They can be utilized interchangeably because the differences between their throughputs are within uncertainty bands. R407C performance was 50% lower. Other disadvantages of using this refrigerant are relatively high working pressures and higher optimal filling ratio (30%).

  5. Theoretical and numerical investigations of inverse patchy colloids in the fluid phase

    International Nuclear Information System (INIS)

    Kalyuzhnyi, Yurij V.; Bianchi, Emanuela; Ferrari, Silvano; Kahl, Gerhard

    2015-01-01

    We investigate the structural and thermodynamic properties of a new class of patchy colloids, referred to as inverse patchy colloids (IPCs) in their fluid phase via both theoretical methods and simulations. IPCs are nano- or micro- meter sized particles with differently charged surface regions. We extend conventional integral equation schemes to this particular class of systems: our approach is based on the so-called multi-density Ornstein-Zernike equation, supplemented with the associative Percus-Yevick approximation (APY). To validate the accuracy of our framework, we compare the obtained results with data extracted from NpT and NVT Monte Carlo simulations. In addition, other theoretical approaches are used to calculate the properties of the system: the reference hypernetted-chain (RHNC) method and the Barker-Henderson thermodynamic perturbation theory. Both APY and RHNC frameworks provide accurate predictions for the pair distribution functions: APY results are in slightly better agreement with MC data, in particular at lower temperatures where the RHNC solution does not converge

  6. Magnetic phase investigations on fluorine (F) doped LiFePO4

    Science.gov (United States)

    Radhamani, A. V.

    2018-03-01

    LiFePO4 (LFP) is a very promising cathode material for Li-ion batteries due to its high thermal stability, less toxicity and high theoretical capacity (170 mAh g-1). Anion doping, especially fluorine (F) at the oxygen site is one way to improve the low electronic conductivity of the material. In this line, fluorine doped LFP was prepared at different fluorine concentrations (1 to 40 mol%) to study the structural, spectroscopic and magnetic properties in view of the material property optimization for battery applications. The investigation of the magnetic properties was found to be successful for the determination of small amounts of magnetic impurities which were not noticeably observed from structural characterizations. Determination of conducting magnetic impurities has its own relevance in the current scenario of Li-ion based battery applications. Systematic characterization studies along with the implications of magnetic phases on the material activity of fluorine doped LiFePO4 nanoparticles will be discussed in detail.

  7. Investigations on the growth kinetics of Laves phase precipitates in 12% Cr creep-resistant steels: Experimental and DICTRA calculations

    Energy Technology Data Exchange (ETDEWEB)

    Prat, O. [Max Planck Institute fuer Eisenforschung GmbH, Max Planck Strasse 1, 40237 Duesseldorf (Germany)] [Universidad de Concepcion, Departamento de Ingenieria de Materiales, Edmundo Larenas 270, Concepcion (Chile); Garcia, J., E-mail: jose.garcia@helmholtz-berlin.de [Helmholtz-Zentrum Berlin fuer Materialien und Energie GmbH, Hahn-Meitner-Platz 1, 14109 Berlin (Germany); Rojas, D. [Max Planck Institute fuer Eisenforschung GmbH, Max Planck Strasse 1, 40237 Duesseldorf (Germany); Carrasco, C. [Universidad de Concepcion, Departamento de Ingenieria de Materiales, Edmundo Larenas 270, Concepcion (Chile); Inden, G. [Max Planck Institute fuer Eisenforschung GmbH, Max Planck Strasse 1, 40237 Duesseldorf (Germany)

    2010-10-15

    The growth kinetics of Laves phase precipitates (type Fe{sub 2}W) in the early stage of creep (650 deg. C for 10,000 h) in two 12% Cr ferrite-martensitic steels has been investigated. In one alloy the Laves phase formed on tempering, while in the second alloy the Laves phase precipitated during creep. Kinetic simulations were performed using the software DICTRA. The particle size of the Laves phase was measured on transmission electron microscopy samples. The equilibrium phase fraction of the Laves phase was reached in the first thousand hours. Simulations of particle growth showed good agreement with the experimental results. Competitive growth between M{sub 23}C{sub 6} and the Laves phase showed that M{sub 23}C{sub 6} carbides reached their equilibrium after 12 days, whereas the Laves phase reached equilibrium after 3 months. Simulations of the influence of the interfacial energy and addition of Co, Cu and Si on Laves phase precipitation are presented.

  8. Small angle neutron scattering form polymer melts: structural investigation and phase behaviour

    International Nuclear Information System (INIS)

    Ertugrul, O.

    2004-01-01

    The Small-Angle Neutron Scattering (SANS) techniques have been used to study the structural properties and phase behavior of polymer melts. A model based on Random Phase Approximation (RPA) is proposed to predict the experimental data. By fitting the model to data we could be able to obtain radius of gyration (a measure of size of a polymer) and phase transition for the sample. (author)

  9. Introduction to investigations of the negative corona and EHD flow in gaseous two-phase fluids

    Science.gov (United States)

    Jerzy, MIZERACZYK; Artur, BERENDT

    2018-05-01

    Research interests have recently been directed towards electrical discharges in multi-phase environments. Natural electrical discharges, such as lightning and coronas, occur in the Earth’s atmosphere, which is actually a mixture of gaseous phase (air) and suspended solid and liquid particulate matters (PMs). An example of an anthropogenic gaseous multi-phase environment is the flow of flue gas through electrostatic precipitators (ESPs), which are generally regarded as a mixture of a post-combustion gas with solid PM and microdroplets suspended in it. Electrical discharges in multi-phase environments, the knowledge of which is scarce, are becoming an attractive research subject, offering a wide variety of possible discharges and multi-phase environments to be studied. This paper is an introduction to electrical discharges in multi-phase environments. It is focused on DC negative coronas and accompanying electrohydrodynamic (EHD) flows in a gaseous two-phase fluid formed by air (a gaseous phase) and solid PM (a solid phase), run under laboratory conditions. The introduction is based on a review of the relevant literature. Two cases will be considered: the first case is of a gaseous two-phase fluid, initially motionless in a closed chamber before being subjected to a negative corona (with the needle-to-plate electrode arrangement), which afterwards induces an EHD flow in the chamber, and the second, of a gaseous two-phase fluid flowing transversely with respect to the needle-to-plate electrode axis along a chamber with a corona discharge running between the electrodes. This review-based introductory paper should be of interest to theoretical researchers and modellers in the field of negative corona discharges in single- or two-phase fluids, and for engineers who work on designing EHD devices (such as ESPs, EHD pumps, and smoke detectors).

  10. Investigation of B2 and related phases in the Ti-Al-Nb ternary systems

    International Nuclear Information System (INIS)

    Bendersky, L.A.; Boettinger, W.J.

    1989-01-01

    Alloy compositions around Ti 2 AlNb were studied to establish phase equilibria and transformations during cooling from 1100 degrees C and 1400 degrees C. In addition to general results obtained on a wide range of compositions, which include evidence for a broad B2 phase field, transformation of BCC Ti 4 Al 3 Nb to a phase with an omega-type structure is reported. Detailed analysis indicates that this phase has the B8 2 structure after annealing at 700 degrees C

  11. Experimental investigation of turbulence modulation in particle-laden coaxial jets by Phase Doppler Anemometry

    Energy Technology Data Exchange (ETDEWEB)

    Mergheni, M.A. [CORIA UMR 6614 CNRS, Universite et INSA de ROUEN, Avenue de l' Universite, BP 12, 76801 Saint Etienne du Rouvray, Cedex (France)]|[LESTE Ecole Nationale d' Ingenieurs de Monastir, 5019 Monastir (Tunisia); Sautet, J.C.; Godard, G. [CORIA UMR 6614 CNRS, Universite et INSA de ROUEN, Avenue de l' Universite, BP 12, 76801 Saint Etienne du Rouvray, Cedex (France); Ben Ticha, H.; Ben Nasrallah, S. [LESTE Ecole Nationale d' Ingenieurs de Monastir, 5019 Monastir (Tunisia)

    2009-03-15

    The effect of solid particles on the flow characteristics of axisymmetric turbulent coaxial jets for two flow conditions was studied. Simultaneous measurements of size and velocity distributions of continuous and dispersed phases in a two-phase flow are presented using a Phase Doppler Anemometry (PDA) technique. Spherical glass particles with a particle diameter range from 102 to 212 {mu}m were used in this two-phase flow, the experimental results indicate a significant influence of the solid particles and the Re on the flow characteristics. The data show that the gas phase has lower mean velocity in the near-injector region and a higher mean velocity at the developed region. Near the injector at low Reynolds number (Re = 2839) the presence of the particles dampens the gas-phase turbulence, while at higher Reynolds number (Re = 11 893) the gas-phase turbulence and the velocity fluctuation of particle-laden jets are increased. The particle velocity at higher Reynolds number (Re = 11 893) and is lower at lower Reynolds number (Re = 2839). The slip velocity between particles and gas phase existed over the flow domain was examined. More importantly, the present experiment results suggest that, consideration of the gas characteristic length scales is insufficient to predict gas-phase turbulence modulation in gas-particle flows. (author)

  12. [Investigations on the physiology of the glands of carnivorous plants : IV. The kinetics of chloride secretion by the gland tissue of Nepenthes].

    Science.gov (United States)

    Lüttge, U

    1966-03-01

    The transport of chloride in isolated tissue from Nepenthes pitchers was investigated using (36)Cl(-), an Aminco-Cotlove chloride-titrator for the determinations of Cl(-) concentrations, and KCN and AsO 4 (-) -as metabolic inhibitors.The tissue was brought in contact with different experimental solutions (=medium). The surface corresponding to the outside of the pitchers was cut with a razor blade to remove the cutinized epidermal layer. At this surface the Cl(-) uptake from the medium is a metabolic process which depends on the Cl(-)-concentration of the medium in a manner that corresponds to the MICHAELIS-MENTEN kinetics. The Michaelis-constant of this transport step was 3×10(-2)M. The Cl(-)-efflux into the medium, however, is a passive process.The opposite surface of the tissue slices (corresponding to the inside of the pitchers) carries the glands. The chloride secretion taking place here is also dependent on metabolism. In vitro it occurs even when a high gradient of chloride concentration has been set up between the medium and the solution which is in contact with the glands. In vivo the Cl(-)-concentration of the pitcher fluid and the amount of Cl(-) per gram of tissue water are almost equal.The rôle of chloride in the physiology of Nepenthes is still under investigation, A correlation between the chloride content of the pitcher fluid and its enzymatic activity (Casein-test), however, could already be demonstrated.

  13. On the biology and food of small-sized fish from North and Baltic Sea areas. IV. Investigations on an eulittoral mud flat at Sylt Island

    Science.gov (United States)

    Zander, C. Dieter; Hartwig, Eike

    1982-03-01

    The fish fauna of an eulittoral mud flat was investigated at Sylt Island (North Sea) with special regard to its food uptake. During the course of a year the following species were caught: Pomatoschistus microps, Anguilla anguilla (elvers), Zoarces viviparus, and Gasterosteus aculeatus. Considering the potentially available food, the most abundant organisms of the benthos were harpacticoids and nematodes, whereas in the phytal layer gastropods and gammarids were dominant. The benthic biomass was found to be greatest in spring, while phytal organisms were most abundant in late summer. The greatest fish density was stated in September 1974 though only P. microps was present. The fish biomass was highest in spring when the elvers appeared. The main food of P. microps was epibenthos; in the diet of A. anguilla phytal organisms dominated over epibenthos, in G. aculeatus suprabenthic organisms were also present. The most prominent food component by biomass was gammarids in all investigated fish, whereas harpacticoids were only dominant in number. During the course of the year the biomass of ingested food yielded highest values in summer and autumn, but lowest in winter. A very great predatory activity was found in September 1974, which possibly caused a grazing effect on harpacticoids. An estimation of the turnover rate of small-sized fish in this month led to a value of 70 mg dry weight m-2 · d-1.

  14. Computational thermodynamic investigations of growth and coarsening of laves phase precipitates in 12%Cr creep resistant steels

    Energy Technology Data Exchange (ETDEWEB)

    Prat, O.; Rojas, D. [Max-Planck-Institut fuer Eisenforschung GmbH, Duesseldorf (Germany); Garcia, J.; Kaysser-Pyzalla, A.R. [Helmholtz-Zentrum Berlin fuer Materialien und Energie GmbH, Berlin (Germany); Bochum Univ. (Germany)

    2010-07-01

    Precipitation phenomena in 12%Cr high alloyed steels have been investigated at creep conditions of 650 and 150 MPa up to 6.500 hours in two different alloys. Growth and coarsening of Laves phase was determined experimentally by measuring the size of Laves phase on crept samples using scanning transmission electron microscopy (STEM). The simulations were performed using the software DICTRA based on the assumption the local equilibrium at the moving phase interface. For equilibrium calculations, the Thermo-Calc software was used. The experimental results were compared with DICTRA simulations, showing good agreement. Both the quantitative metallographic measurements as well as the simulations indicate very low coarsening for Laves Phase. The influence of different elements such as Co, Si and Cu on coarsening for Laves phase was simulated. (orig.)

  15. A Wims E analysis of the zero energy experiments of Dragon prior to charge IV - Part 3: Prelmininary investigations into the control rod representation and related problems

    Energy Technology Data Exchange (ETDEWEB)

    Dubofsky, W; Woloch, F

    1973-09-28

    In the collaboration between UKAEA and Dragon for Zero Energy Experiment Evaluation, Dragon is to undertake all investigations needed for the representation of specific features of the Dragon Reactor experiment which are not necessarily characteristic of the large HTR system. One quite obvious uniqueness of Dragon is the location of the control rods situated in the radial reflector, only a few thermal mean free paths away from the core reflector boundary. In the first onslaught it is our intention to use the already available WIMS modules as much as possible and to identify difficulties in doing so. Finally it will be profitable to consider if the control rod representation found as a result of the whole exercise lends itself for the routine calculations of Dragon. In this paper Section 2 describes the geometrical difficulties to be overcome. Section 3 presents the results of calculations so far available. Section 4 gives the layout of further calculations planned and Section 5 presents the conclusions.

  16. Neptunium (IV) oxalate solubility

    International Nuclear Information System (INIS)

    Luerkens, D.W.

    1983-07-01

    The equilibrium solubility of neptunium (IV) oxalate in nitric/oxalic acid solutions was determined at 22 0 C, 45 0 C, and 60 0 C. The concentrations of nitric/oxalic acid solutions represented a wide range of free oxalate ion concentration. A mathematical solubility model was developed which is based on the formation of the known complexes of neptunium (IV) oxalate. the solubility model uses a simplified concentration parameter which is proportional to the free oxalate ion concentration. The solubility model can be used to estimate the equilibrium solubility of neptunium (IV) oxalate over a wide range of oxalic and nitric acid concentrations at each temperature

  17. Experimental Investigations of Noise Control in Planetary Gear Set by Phasing

    Directory of Open Access Journals (Sweden)

    S. H. Gawande

    2014-01-01

    Full Text Available Now a days reduction of gear noise and resulting vibrations has received much attention of the researchers. The internal excitation caused by the variation in tooth mesh stiffness is a key factor in causing vibration. Therefore to reduce gear noise and vibrations several techniques have been proposed in recent years. In this research the experimental work is carried out to study the effect of planet phasing on noise and subsequent resulting vibrations of Nylon-6 planetary gear drive. For this purpose experimental set-up was built and trials were conducted for two different arrangements (i.e., with phasing and without phasing and it is observed that the noise level and resulting vibrations were reduced by planet phasing arrangement. So from the experimental results it is observed that by applying the meshing phase difference one can reduce planetary gear set noise and vibrations.

  18. Exploration of phase transition in Th2C under pressure: An Ab-initio investigation

    Science.gov (United States)

    Sahoo, B. D.; Joshi, K. D.; Kaushik, T. C.

    2018-05-01

    With the motivation of searching for new compounds in the Th-C system, we have performed ab initio evolutionary searches for all the stable compounds in this binary system in the pressure range of 0-100 GPa. We have found previously unknown, thermodynamically stable, composition Th2C along with experimentally known ThC, ThC2 and Th2C3 phases at 0 GPa. Interestingly at pressure of 13 GPa the predicted ground state orthorhombic (SG no. 59, Pmmn) phase of Th2C transforms to trigonal (SG no. 164, P-3m1) phase. We also find the mechanical and dynamical stability of both the phases. Further, the theoretically determined equation of state has been utilized to derive various physical quantities such as zero pressure equilibrium volume, bulk modulus, and pressure derivative of bulk modulus of Pmmn phase at ambient conditions.

  19. An investigation of the Pd-Ag-Ru-Gd quaternary system phase diagram

    International Nuclear Information System (INIS)

    Zhang Kanghou; Xu Yun

    2005-01-01

    On the basis of the Ag-Pd-Gd, Ag-Ru-Gd and Pd-Ru-Gd ternary systems, the partial phase diagram of Pd-Ag-Ru-Gd (Gd 3 Gd and Ag 51 Gd 14 ; five two-phase regions: Pd(Ag) + (Ru), Pd(Ag) + Ag 51 Gd 14 (Ru) + Ag 51 Gd 14 , Pd(Ag) + Pd 3 Gd and (Ru) + Pd 3 Gd; three three-phase regions: Pd(Ag) + Pd 3 Gd + (Ru), Pd(Ag) + Ag 51 Gd 14 + (Ru) and (Ru) + Ag 51 Gd 14 + Pd 3 Gd; one four-phase region Pd(Ag) + (Ru) + Ag 51 Gd 14 + Pd 3 Gd. No new quaternary intermetallic phase has been found

  20. A fluid biopsy as investigating technology for the fluid phase of solid tumors

    Science.gov (United States)

    Kuhn, Peter; Bethel, Kelly

    2012-02-01

    , which has shown predictive utility in several cancer types—the blurry outlines of things to come began to coalesce. The field of CTC research is in its adolescence; enumeration and characterization research effort is methodologically varied, vigorously individuated and rich in innovation. The high definition CTC (HD-CTC) assay described herein and applied to several currently relevant research questions about cancer spread represents a new measure of an internal biologic process that will hopefully lead to great advancements in cancer medicine. First, the paper entitled 'Fluid biopsy in patients with metastatic prostate, pancreatic and breast cancers' by Marrinucci et al, represents the initial technical and clinical validation of an enrichment-free assay and demonstrates our ability to identify significant numbers of HD-CTCs in a majority of patients with prostate, breast and pancreatic cancers. It demonstrates very high rates of detection (>50%) in breast, prostate and pancreatic cancer patients with no CTCs found in normal control subjects. The assay detects significantly higher numbers of CTCs than the FDA-approved Cellsearch® assay and shows the presence of clusters of CTCs in many patients. The nature of the clusters is further evaluated in 'Characterization of circulating tumor cell aggregates identified in patients with epithelial tumors' by Cho et al, wherein CTC aggregates are identified in 43% of 86 patient samples. The fraction of CTC aggregation was investigated in blood draws from 24 breast, 14 non-small cell lung (NSCLC), 18 pancreatic, 15 prostate stage IV cancer patients and 15 normal blood donors (NBD). Cells contained in CTC aggregates had less area and length, on average, than single CTCs. The nuclear to cytoplasmic (N/C) ratio between single CTCs and CTC aggregates was similar. To assist with translating into patients the substantial cell biology work done using cell line cells instead of human tumor tissue, the paper entitled 'Cytometric

  1. Variability of Disk Emission in Pre-main-sequence and Related Stars. IV. Investigating the Structural Changes in the Inner Disk Region of MWC 480

    Science.gov (United States)

    Fernandes, Rachel B.; Long, Zachary C.; Pikhartova, Monika; Sitko, Michael L.; Grady, Carol A.; Russell, Ray W.; Luria, David M.; Tyler, Dakotah B.; Bayyari, Ammar; Danchi, William; Wisniewski, John P.

    2018-04-01

    We present five epochs of near-IR observations of the protoplanetary disk around MWC 480 (HD 31648) obtained with the SpeX spectrograph on NASA’s Infrared Telescope Facility between 2007 and 2013, inclusive. Using the measured line fluxes in the Pa β and Br γ lines, we found the mass accretion rates to be (1.26–2.30) × 10‑7 M ⊙ yr‑1 and (1.4–2.01) × 10‑7 M ⊙ yr‑1, respectively, but which varied by more than 50% from epoch to epoch. The spectral energy distribution reveals a variability of about 30% between 1.5 and 10 μm during this same period of time. We investigated the variability using of the continuum emission of the disk in using the Monte-Carlo Radiative Transfer Code HOCHUNK3D. We find that varying the height of the inner rim successfully produces a change in the NIR flux but lowers the far-IR emission to levels below all measured fluxes. Because the star exhibits bipolar flows, we utilized a structure that simulates an inner disk wind to model the variability in the near-IR, without producing flux levels in the far-IR that are inconsistent with existing data. For this object, variable near-IR emission due to such an outflow is more consistent with the data than changing the scale height of the inner rim of the disk.

  2. Experimental investigation on two-phase thermosyphon loop with partially liquid-filled downcomer

    International Nuclear Information System (INIS)

    Zhang, Penglei; Wang, Baolong; Shi, Wenxing; Li, Xianting

    2015-01-01

    Highlights: • A visual thermosyphon loop test bench is established. • Partially liquid-filled phenomenon in the downcomer is discovered. • The driving force may be smaller than the conventional prediction. • Liquid head in the downcomer is self-regulated by influencing factors. • Larger height difference does not always lead to better performance. - Abstract: Two-phase thermosyphon loops (TPTLs) are beginning to be extensively used in the field of air conditioning and heat recovery, where they have quite different flow characteristics compared with the traditional TPTLs used in cooling of electronics. However, in the existing studies, the flow features in the downcomer were ignored, and most researchers simply thought the downcomer was always full of liquid. In this study, a visual experimental setup was established, the flow features in the downcomer were observed and measured. And the influencing factors including temperature difference, liquid charge, height difference, and circulation flow resistance on the liquid head have been identified and investigated experimentally. The results show that, different from the conventional understandings, the downcomer can be partially liquid filled. At this time, the upper part of downcomer is a static saturation gas blockage, surrounded by a layer of liquid film, which does not provide the driving force. The liquid head in the downcomer, which provides the driving force, shows great self-regulation ability with different working conditions. Increasing the refrigerant charge, temperature difference, circulation flow resistance, and decreasing the height difference drives the liquid head to rise, and the downcomer tends to be fully liquid filled.

  3. Experimental and numerical investigation of dual phase steels formability during laser-assisted hole-flanging

    Science.gov (United States)

    Motaman, S. A. H.; Komerla, K.; Storms, T.; Prahl, U.; Brecher, C.; Bleck, W.

    2018-05-01

    Today, in the automotive industry dual phase (DP) steels are extensively used in the production of various structural parts due to their superior mechanical properties. Hole-flanging of such steels due to simultaneous bending and stretching of sheet metal, is complex and associated with some issues such as strain and strain rate localization, development of micro-cracks, inhomogeneous sheet thinning, etc. In this study an attempt is made to improve the formability of DP sheets, by localized Laser heating. The Laser beam was oscillated in circular pattern rapidly around the pre-hole, blanked prior to the flanging process. In order to investigate formability of DP steel (DP1000), several uniaxial tensile tests were conducted from quasi to intermediate strain rates at different temperatures in warm regime. Additionally, experimentally acquired temperature and strain rate-dependent flow curves were fed into thermomechanical finite element (FE) simulation of the hole-flanging process using the commercial FE software ABAQUS/Explicit. Several FE simulations were performed in order to evaluate the effect of blank's initial temperature and punch speed on deformation localization, stress evolution and temperature distribution in DP1000 sheets during warm hole-flanging process. The experimental and numerical analyses revealed that prescribing a distribution of initial temperature between 300 to 400 °C to the blank and setting a punch speed that accommodates strain rate range of 1 to 5 s-1 in the blank, provides the highest strain hardening capacity in the considered rate and temperature regimes for DP1000. This is in fact largely due to the dynamic strain aging (DSA) effect which occurs due to pinning of mobile dislocations by interstitial solute atoms, particularly at elevated temperatures.

  4. Structural properties of the metastable state of phase change materials investigated by synchrotron radiation

    Energy Technology Data Exchange (ETDEWEB)

    Merkelbach, Philipp; Eijk, Julia van; Wuttig, Matthias [I. Phys. Institut (IA), RWTH Aachen, 52056 Aachen (Germany); Braun, Carolin [Institut fuer Anorg. Chemie, CAU Kiel, 24098 Kiel (Germany)

    2008-07-01

    Phase change alloys are among the most promising materials for novel data storage devices. Since several years Phase Change Materials based on Ge-Sb-Te- alloys have been used in optical data storage solutions like rewriteable CDs and DVDs. Recently these alloys have been explored as potential candidates for fast nonvolatile electrical data storage devices in Phase Change Random Access Memory (PCRAM). Besides attracting considerable interest from the commercial point of view phase change materials are very interesting also due to their remarkable physical properties. They have the ability to be reversibly switched within a few nanoseconds between the amorphous and the crystalline phase, while changing their physical properties such as optical reflectivity and electrical resistivity significantly. Even though the electronic properties show a drastical contrast such fast transitions can only be caused by small atomic rearrangements. This behavior calls for a deeper understanding of the structural properties of the alloys. We have performed powder diffraction measurements of the crystal phase of various GeSbTe alloys, to determine the structural similarities and differences of several alloys. Understanding the crystal structure of phase change materials is a key to a deeper insight into the properties of these promising materials.

  5. Milestone in the NTB phase investigation and beyond: direct insight into molecular self-assembly.

    Science.gov (United States)

    Ivšić, Trpimir; Vinković, Marijana; Baumeister, Ute; Mikleušević, Ana; Lesac, Andreja

    2014-12-14

    Although liquid-crystalline materials are most widely exploited for flat-panel displays, their ability to self-organize into periodically ordered nanostructures gives rise to a broad variety of additional applications. The recently discovered low-temperature nematic phase (N(TB)) with unusual characteristics generated considerable attention within the scientific community: despite the fact that the molecules from which the phase is composed are not chiral, the helicoidal structure of the phase is strongly implicated. Here we report on combined experimental, computational and spectroscopic studies of the structural aspects influencing formation of the N(TB) phase as well as on the molecular organization within the phase. In an extensive DFT study, the structure-property prerequisite was traced to a "bent-propeller" shape of the molecule. We also demonstrate the first utilization of liquid state NMR for direct analysis of intermolecular interactions within thermotropic liquid-crystalline phases, providing new insight into molecular packing that can lead towards design of novel chiral functional materials. The synergy of experimental, computational and NMR studies suggests a syn-parallel helical molecular organization within the N(TB) phase.

  6. Investigations of environmental induced effects on AlQ3 thin films by AFM phase imaging

    International Nuclear Information System (INIS)

    Shukla, Vivek Kumar; Kumar, Satyendra

    2007-01-01

    Tris(8-hydroxyquinoline) metal complex (AlQ 3 ) is a widely used light-emitting material in organic light emitting devices (OLEDs). The environmental stability is still a major problem with OLEDs and needs further improvement. In this report, an additional feature of Atomic Force Microscopy (AFM) was exploited with the aim to understand the environmental induced effects and physical phenomenon involved on AlQ 3 thin films. We have used phase imaging to identify the presence of other aggregation phases formed after annealing the thin film in different ambient and after white light exposure. An enhanced photoluminescence intensity is observed for the samples annealed in oxygen near 100 deg. C. The enhanced photoluminescence is understood in terms of formation of a new aggregation phase. The phase change and the fraction of new phase is estimated by phase images taken by atomic force microscopy (AFM). Light induced effects on AlQ 3 films exposed to white light in air and vacuum are characterized by atomic force microscopy (AFM) for surface morphology and phases present. The AFM images indicate enhanced crystallinity for the vacuum exposed samples. The phase with increased lifetime and hence enhanced crystallinity for vacuum exposed films has also been found by time correlated single photon counting (TCSPC) measurements. To the best of our knowledge, this study is applied for the first time on this material with the combination of topography and phase imaging in atomic force microscopy (AFM). The major aim was to take advantage of the additional feature of AFM-mode over the conventionally used

  7. An investigation of time-frequency domain phase-weighted stacking and its application to phase-velocity extraction from ambient noise's empirical Green's functions

    Science.gov (United States)

    Li, Guoliang; Niu, Fenglin; Yang, Yingjie; Xie, Jun

    2018-02-01

    The time-frequency domain phase-weighted stacking (tf-PWS) technique based on the S transform has been employed in stacking empirical Green's functions (EGFs) derived from ambient noise data, mainly due to its superior power in enhancing weak signals. Questions such as the induced waveform distortion and the feasibility of phase-velocity extraction are yet to be thoroughly explored. In this study, we investigate these issues by conducting extensive numerical tests with both synthetic data and USArray transportable array (TA) ambient noise data. We find that the errors in the measured phase velocities associated with waveform distortion caused by the tf-PWS depend largely on the way of how the inverse S transform (IST) is implemented. If frequency IST is employed in tf-PWS, the corresponding errors are generally less than 0.1 per cent, sufficiently small that the measured phase velocities can be safely used in regular surface wave tomography. On the other hand, if a time IST is used in tf-PWS, then the extracted phase velocities are systematically larger than those measured from linearly stacked ones, and the discrepancy can reach as much as ˜0.4 per cent at some periods. Therefore, if tf-PWS is used in stacking EGFs, then frequency IST is preferred to transform the stacked S spectra back to the time domain for the stacked EGFs.

  8. NNDSS - Table IV. Tuberculosis

    Data.gov (United States)

    U.S. Department of Health & Human Services — NNDSS - Table IV. Tuberculosis - 2016.This Table includes total number of cases reported in the United States, by region and by states, in accordance with the...

  9. NNDSS - Table IV. Tuberculosis

    Data.gov (United States)

    U.S. Department of Health & Human Services — NNDSS - Table IV. Tuberculosis - 2014.This Table includes total number of cases reported in the United States, by region and by states, in accordance with the...

  10. NNDSS - Table IV. Tuberculosis

    Data.gov (United States)

    U.S. Department of Health & Human Services — NNDSS - Table IV. Tuberculosis - 2015.This Table includes total number of cases reported in the United States, by region and by states, in accordance with the...

  11. SAGE IV Pathfinder

    Data.gov (United States)

    National Aeronautics and Space Administration — Utilizing a unique, new occultation technique involving imaging, the SAGE IV concept will meet or exceed the quality of previous SAGE measurements at a small...

  12. A spectroscopic and catalytic investigation of active phase-support interactions

    Energy Technology Data Exchange (ETDEWEB)

    Haller, G.L.

    1991-01-01

    Active catalytic phases (metal, mixed metals, oxide or mixed oxides) interacting with oxide support on which the active phase is dispersed can affect the percentage exposed, the morphology of supported particles, the degree of reducibility of cations, etc., in a variety of ways. Our objective is to characterize the physical chemistry of the active phase-oxide support by spectroscopic methods and to correlate this structure with catalytic function. The three systems discussed in this progress report are Ag/TiO{sub 2}, Ru-Cu/SiO{sub 2} and SiO{sub 2}/Al{sub 2}O{sub 3}. 24 refs., 3 figs., 2 tabs.

  13. Investigation of the resistive phase in high power gas switching. Research and development report

    International Nuclear Information System (INIS)

    O'Rourke, R.C.

    1977-01-01

    A theoretical study was made of the resistive phase in high pressure gas switching with the regime of interest being (10 to 50) kV from (1J, 10ns, 100KHz) to (100J, 10μs, 1KHz). The resistive phase was examined as a function of applied field, gap spacing, inductance, gas type and pressure, and electrode material. The initiating and quenching phases as regards system performance (e.g., the jitter problem) were examined. The cooling and electrode debris removal effects of the vortex gas flow on the operating characteristics of the system were considered

  14. [Nationwide sensitivity surveillance of ciprofloxacin and various parenteral antibiotics against bacteria isolated from patients with severe infections--the first Ciproxan IV special investigation in 2001].

    Science.gov (United States)

    Yamaguchi, Keizo; Ishii, Yoshikazu; Iinuma, Yoshitsugu; Yamanaka, Kiyoharu; Ichiyama, Satoshi; Watanabe, Naoki; Uehara, Nobuyuki; Kaku, Mitsuo; Kurokawa, Yukinori; Hayashi, Mutsumu; Hirakata, Yoichi

    2003-12-01

    The parenteral injection of ciprofloxacin (CPFX), a fluoroquinolone antimicrobial drug, was approved in September 2000 and a re-examination period of 6 years was set at that time. As a special investigation to apply for re-examination of this drug, it has been planned to conduct 3 nationwide surveillances during the re-examination period by collecting clinically isolated bacteria from patients with severe infections, to whom the drug was mainly indicated, and examining drug susceptibilities of the bacteria to various parenteral antimicrobial drugs including CPFX. This time, we determined the minimum inhibitory concentrations (MICs) of various parenteral antimicrobial drugs including CPFX against 1,220 strains isolated from patients with severe infections by the micro-liquid dilution method and compared susceptibilities of various clinically isolated bacteria to CPFX with those to other antimicrobial drugs. Gram-positive bacteria were less susceptible to CPFX than to carbapenems except 2 bacterial species, Enterococcus faecium and Enterococcus avium but susceptibilities of methicillin-susceptible Staphylococcus aureus (MSSA), Staphylococcus epidermidis and Enterococcus faecalis to CPFX were comparable to those to cefozopran. Susceptibility of Streptococcus pneumoniae to CPFX did not differ among ampicillin (ABPC)-susceptible Streptococcus pneumoniae (MIC of ABPC: MIC of ABPC: 0.25-2 micrograms/ml) and ABPC-resistant S. pneumoniae (MIC of ABPC: > or = 4 micrograms/ml) MIC90 of CPFX: 1 microgram/ml) and a decrease in the antimicrobial activity seen among cephem and carbapenem antimicrobial drugs against penicillin-intermediate strains was not noted with CPFX. Gram-negative bacteria were susceptible to CPFX similarly to carbapenems and the MIC90 values of CPFX were in the range from MIC90 was 2 micrograms/ml. CPFX also showed the lowest MIC90 value (0.5 microgram/ml) against beta-lactam-resistant P. aeruginosa among the drugs examined. When extended-spectrum beta

  15. Dilute Oxygen Combustion Phase IV Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Riley, M.F.

    2003-04-30

    Novel furnace designs based on Dilute Oxygen Combustion (DOC) technology were developed under subcontract by Techint Technologies, Coraopolis, PA, to fully exploit the energy and environmental capabilities of DOC technology and to provide a competitive offering for new furnace construction opportunities. Capital cost, fuel, oxygen and utility costs, NOx emissions, oxide scaling performance, and maintenance requirements were compared for five DOC-based designs and three conventional air5-fired designs using a 10-year net present value calculation. A furnace direct completely with DOC burners offers low capital cost, low fuel rate, and minimal NOx emissions. However, these benefits do not offset the cost of oxygen and a full DOC-fired furnace is projected to cost $1.30 per ton more to operate than a conventional air-fired furnace. The incremental cost of the improved NOx performance is roughly $6/lb NOx, compared with an estimated $3/lb. NOx for equ8pping a conventional furnace with selective catalytic reduction (SCCR) technology. A furnace fired with DOC burners in the heating zone and ambient temperature (cold) air-fired burners in the soak zone offers low capital cost with less oxygen consumption. However, the improvement in fuel rate is not as great as the full DOC-fired design, and the DOC-cold soak design is also projected to cost $1.30 per ton more to operate than a conventional air-fired furnace. The NOx improvement with the DOC-cold soak design is also not as great as the full DOC fired design, and the incremental cost of the improved NOx performance is nearly $9/lb NOx. These results indicate that a DOC-based furnace design will not be generally competitive with conventional technology for new furnace construction under current market conditions. Fuel prices of $7/MMBtu or oxygen prices of $23/ton are needed to make the DOC furnace economics favorable. Niche applications may exist, particularly where access to capital is limited or floor space limitations are critical. DOC technology will continue to have a highly competitive role in retrofit applications requiring increases in furnace productivity.

  16. Clean Cast Steel Technology, Phase IV

    Energy Technology Data Exchange (ETDEWEB)

    Charles E. Bates

    2003-02-24

    The objective of the Clean Cast Steel Technology Program was to improve casting product quality by removing or minimizing oxide defects and to allow the production of higher integrity castings for high speed machining lines. Previous research has concentrated on macro-inclusions that break, chip, or crack machine tool cutters and drills and cause immediate shutdown of the machining lines. The overall goal of the project is to reduce the amount of surface macro-inclusions and improve the machinability of steel castings. Macro-inclusions and improve the machinability of steel castings. Macro-inclusions have been identified by industrial sponsors as a major barrier to improving the quality and marketability of steel castings.

  17. Investigation of flow dynamics of liquid phase in a pilot-scale trickle bed reactor using radiotracer technique.

    Science.gov (United States)

    Pant, H J; Sharma, V K

    2016-10-01

    A radiotracer investigation was carried out to measure residence time distribution (RTD) of liquid phase in a trickle bed reactor (TBR). The main objectives of the investigation were to investigate radial and axial mixing of the liquid phase, and evaluate performance of the liquid distributor/redistributor at different operating conditions. Mean residence times (MRTs), holdups (H) and fraction of flow flowing along different quadrants were estimated. The analysis of the measured RTD curves indicated radial non-uniform distribution of liquid phase across the beds. The overall RTD of the liquid phase, measured at the exit of the reactor was simulated using a multi-parameter axial dispersion with exchange model (ADEM), and model parameters were obtained. The results of model simulations indicated that the TBR behaved as a plug flow reactor at most of the operating conditions used in the investigation. The results of the investigation helped to improve the existing design as well as to design a full-scale industrial TBR for petroleum refining applications. Copyright © 2016 Elsevier Ltd. All rights reserved.

  18. Investigation of phase separated polyimide blend films containing boron nitride using FTIR imaging

    Science.gov (United States)

    Chae, Boknam; Hong, Deok Gi; Jung, Young Mee; Won, Jong Chan; Lee, Seung Woo

    2018-04-01

    Immiscible aromatic polyimide (PI) blend films and a PI blend film incorporated with thermally conductive boron nitride (BN) were prepared, and their phase separation behaviors were examined by optical microscopy and FTIR imaging. The 2,2‧-bis(trifluoromethyl)benzidine (TFMB)-containing and 4,4‧-thiodianiline (TDA)-containing aromatic PI blend films and a PI blend/BN composite film show two clearly separated regions; one region is the TFMB-rich phase, and the other region is the TDA-rich phase. The introduction of BN induces morphological changes in the immiscible aromatic PI blend film without altering the composition of either domain. In particular, the BN is selectively incorporated into the TDA-rich phase in this study.

  19. Investigation of two-phase bubbly flows using laser doppler anemometry

    OpenAIRE

    Marié , Jean-Louis

    1983-01-01

    International audience; The present work is devoted to the development of an accurate and reliable laser Doppler anemometer technique (L.D.A.) meant for the measurement of the characteristics of twoephase bubbly flows. Most of these characteristics are the various statistical moments of the velocity fluctuations and the Reynolds stress tensor components within the continuous phase but also, under well defined conditions, the mean slip velocity of the dispersed phase. Although this technique w...

  20. Adduct formation in Ce(IV) thenolytrifluoroacetonate

    International Nuclear Information System (INIS)

    Anufrieva, S.I.; Polyakova, G.V.; Snezhko, N.I.; Pechurova, N.I.; Martynenko, L.I.; Spitsyn, V.I.

    1982-01-01

    The literature contains no information on adduct formation in Ce(IV) β-diketonates with additional ligands. Since tetrakis-β-diketonates of Ce(IV) have four six-membered chelate rings, we can suppose that the introduction of an additional monodentate or bidentate ligand into the coordination sphere of Ce(IV) β-diketonates would lead to an increase in the coordination number (CN) of the Ce(IV) to nine or ten. The possibility of realization of such a high CN for Ce(IV) has not been proved; a study of adduct formation by Ce(IV) tetrakis-β-diketonates is thus of theoretical interest. Such an investigation might also be of practical interest, because the introduction of an additional ligand into the coordination sphere of a rare-earth β-diketonate usually increases the solubility of the β-diketonate in nonpolar solvents and increases the volatility of the compound; such a modification of the properties is important for various practical purposes. The aim of our work was to study the possibility of separating solid adducts of Ce(IV) tetrakis-thenoyltrifluoroacetonate with certain oxygen-containing and nitrogen-containing donor monodentate and bidentate ligands, and also to investigate their properties. As the β-diketone we used thenoyltrifluoroacetone (HTTFA), since in a parallel investigation it was found that Ce(TTFA) 4 has a high oxidation-reduction stability

  1. Investigations into the molecular mechanism of chromatid breakage in the G2-phase of mammalian cells

    International Nuclear Information System (INIS)

    Bryant, P.E.; Armstrong, G.N.; Gray, L.; Frankenberg, D.; Mozdarani, H.

    2003-01-01

    Chromatid breakage following irradiation of cells in the G2-phase of the cell cycle results from the induction of DNA double-strand breaks (dsb). The conversion of dsb into chromatid breaks (cb) has a genetic basis, seemingly different from that of dsb rejoining. The variation in extent of this conversion is exemplified by the stiking variation in frequency of cb in irradiated cycling T-lymphocytes between different normal individuals. Elevated cb frequency in lymphocytes of around 40% of breast cancer patients and their first-degree relatives suggests the presence of mutations in low penetrance cancer predisposing genes that also affect conversion of dsb to cb. Investigation of the mechanism of chromatid radiosensitivity using genetically engineered rodent cell lines containing unique dsb break sites indicate that a single isolated dsb is sufficient to cause a cb. The single-event nature of chromatid breakage is confirmed by the fact that cb are induced as a linear function of radiation dose. Moreover, we have recently shown that ultrasoft carbon-K X-rays also induce chromatid breakage. In this case the energy of the secondary electrons produced by carbon-K X-rays is too low to span more than one DNA double helix, thus further supporting our conclusion that a single dsb is responsible for the formation of a cb. Chromatid breakage is thought to involve a rearrangement between DNA strands at the crossover points of chromatin loop(s) triggered by the presence of a dsb within the loop structure. The occasional observation of 'looped-out' sections of chromatin at cb sites supports this hypothesis. The occurrence of 'colour-switches' between FPG stained chromatids at a proportion of break sites (e.g. about 16% in CHO cells) shows that a significant proportion of cb definitely result from chromatin rearrangements. Measurements of altered colour-switch ratio (csr) in mutant rodent and human cells (irs1 and AT cells respectively) also indicate a genetic basis for the

  2. Investigation of global particulate nitrate from the AeroCom phase III experiment

    Directory of Open Access Journals (Sweden)

    H. Bian

    2017-11-01

    Full Text Available An assessment of global particulate nitrate and ammonium aerosol based on simulations from nine models participating in the Aerosol Comparisons between Observations and Models (AeroCom phase III study is presented. A budget analysis was conducted to understand the typical magnitude, distribution, and diversity of the aerosols and their precursors among the models. To gain confidence regarding model performance, the model results were evaluated with various observations globally, including ground station measurements over North America, Europe, and east Asia for tracer concentrations and dry and wet depositions, as well as with aircraft measurements in the Northern Hemisphere mid-to-high latitudes for tracer vertical distributions. Given the unique chemical and physical features of the nitrate occurrence, we further investigated the similarity and differentiation among the models by examining (1 the pH-dependent NH3 wet deposition; (2 the nitrate formation via heterogeneous chemistry on the surface of dust and sea salt particles or thermodynamic equilibrium calculation including dust and sea salt ions; and (3 the nitrate coarse-mode fraction (i.e., coarse/total. It is found that HNO3, which is simulated explicitly based on full O3-HOx-NOx-aerosol chemistry by all models, differs by up to a factor of 9 among the models in its global tropospheric burden. This partially contributes to a large difference in NO3−, whose atmospheric burden differs by up to a factor of 13. The atmospheric burdens of NH3 and NH4+ differ by 17 and 4, respectively. Analyses at the process level show that the large diversity in atmospheric burdens of NO3−, NH3, and NH4+ is also related to deposition processes. Wet deposition seems to be the dominant process in determining the diversity in NH3 and NH4+ lifetimes. It is critical to correctly account for contributions of heterogeneous chemical production of nitrate on dust and sea salt, because this process

  3. Direct investigations of the immobilization of radionuclides in the alteration phases of spent nuclear fuel. 1998 annual progress report

    International Nuclear Information System (INIS)

    Burns, P.C.; Finch, R.J.

    1998-01-01

    'In an oxidizing environment, such as in the proposed repository at Yucca Mountain, rapid alteration rates are expected for spent nuclear fuel. Lab.-scale simulations have repeatedly shown that the dominant alteration products under repository conditions will be uranyl phases. There is an inadequate database that relates to the effects of the alteration products on the release of radionuclides, but this information is essential to provide a radionuclide release estimate. It is likely that many of the radionuclides contained in the fuel will be incorporated into the alteration products that form, potentially with a profound impact on the future mobility of radionuclides in the repository. The authors objective is to characterize the incorporation of radionuclides into alteration products by synthesis of uranyl phases doped with radionuclides, appropriate surrogate elements, or non-radioactive isotopes, followed by detailed phase characterization by diffraction and spectroscopic techniques. The research will permit a more realistic estimate of the release rates of the radionuclides from the near-field environment. This report summarizes work after 8 months of a 3-year project. The objective of investigating radionuclide incorporation in uranyl phases has required the development of synthesis techniques for various uranyl phases that are expected to form under repository conditions. The authors have synthesized and determined the structures of several uranyl phases that are new to science and that may be important alteration products under repository conditions. They have also undertaken the determination and refinement of the crystal structures of various uranyl phases that are likely to form under repository conditions. Other experiments include the investigation of the ion-exchange properties of uranyl phases under repository conditions.'

  4. Experimental investigation of the ternary system Ni–Pd–Sn with special focus on the B8-type phase

    International Nuclear Information System (INIS)

    Jandl, Isabella; Ipser, Herbert; Richter, Klaus W.

    2015-01-01

    The ternary alloy system Ni–Pd–Sn was investigated experimentally from 700 °C upwards, with special focus on the general NiAs-type compounds. The phase diagram and crystallographic parameters were studied by means of powder X-ray diffraction (XRD), differential thermal analysis (DTA), light optical microscopy (LOM) and scanning electron microscopy (SEM) in combination with energy dispersive X-ray spectroscopy (EDX). An isothermal section at 700 °C was constructed wherein a continuous phase field between the binary NiAs-type compounds γ (PdSn) and Ni 3 Sn 2 (high temperature modification) was detected. A series of samples throughout this phase field was used to investigate lattice parameter variations, occupation of the atomic sites and the melting behaviour. A partial ordering of the transition metals was observed. Moreover, three vertical sections at 30 at.%, 40 at.% and 50 at.% Sn were determined. Altogether, seven ternary invariant phase reactions were discovered: two ternary eutectic reactions, one ternary eutectoid reaction, three ternary transition reactions and one maximum. A complete reaction scheme for the investigated temperature range is given. Furthermore, a partial liquidus surface projection, except for the low-temperature Sn-rich region, was developed. - Highlights: • Detailed study of the ternary alloy system Ni–Pd–Sn. • 1 Isotherm, 3 vertical sections, a partial liquidus projection and a reaction scheme. • A continuous phase field, between γ and Ni 3 Sn 2 , was discovered. • Lattice parameters and structural features in this phase field were analysed. • A partial order of Ni and Pd in this phase field was observed

  5. Data compilation task report for the source investigation of the 300-FF-1 operable unit phase 1 remedial investigation

    International Nuclear Information System (INIS)

    Young, J.S.; Fruland, R.M.; Fruchter, J.S.

    1990-02-01

    This report provides additional information on facility and waste characteristics for the 300-FF-1 operable unit. The additional information gathered and reported includes meetings and on-site visits with current and past personnel having knowledge of operations in the operable unit, a more precise determination of the location of the Process Sewer lines and Retired Radioactive Liquid Waste Sewer, a better understanding of the phosphoric acid spill at the 340 Complex, and a search for engineering plans and environmental reports related to the operable unit. As a result of this data-gathering effort, recommendations for further investigation include characterization of the 307 Trenches to determine the origin of an underlying uranium plume in the groundwater, more extensive sampling of near-surface and dike sediments in the North and South Process Ponds to better define the extent of horizontal contamination, and detection of possible leaks in the abandoned Radioactive Waste Sewer by either electromagnetic induction or remote television camera inspection techniques. 16 refs., 4 figs., 5 tabs

  6. Change from subcutaneous to intravenous abatacept and back in patients with rheumatoid arthritis as simulation of a vacation: a prospective phase IV, open-label trial (A-BREAK).

    Science.gov (United States)

    Mueller, Ruediger B; Gengenbacher, Michael; Richter, Symi; Dudler, Jean; Möller, Burkhard; von Kempis, Johannes

    2016-04-14

    75 % of subjects. Four serious AEs were described during the study. None of them was related to the investigational product, and all serious AEs could be resolved during hospitalization. This prospective, open-label study of abatacept shows for the first time that switching from weekly SC to IV abatacept and back after 4 weeks is an effective and safe way to bridge vacations in RA patients in LDA or remission. (NCT1846975, registered April 19, 2013.).

  7. Investigation of the imaging quality of synchrotron-based phase-contrast mammographic tomography

    International Nuclear Information System (INIS)

    Gureyev, T E; Mayo, S C; Nesterets, Ya I; Mohammadi, S; Menk, R H; Arfelli, F; Tromba, G; Lockie, D; Pavlov, K M; Kitchen, M J; Zanconati, F; Dullin, C

    2014-01-01

    We report the results of a systematic study of phase-contrast x-ray computed tomography in the propagation-based and analyser-based modes using specially designed phantoms and excised breast tissue samples. The study is aimed at the quantitative evaluation and subsequent optimization, with respect to detection of small tumours in breast tissue, of the effects of phase contrast and phase retrieval on key imaging parameters, such as spatial resolution, contrast-to-noise ratio, x-ray dose and a recently proposed ‘intrinsic quality’ characteristic which combines the image noise with the spatial resolution. We demonstrate that some of the methods evaluated in this work lead to substantial (more than 20-fold) improvement in the contrast-to-noise and intrinsic quality of the reconstructed tomographic images compared with conventional techniques, with the measured characteristics being in good agreement with the corresponding theoretical estimations. This improvement also corresponds to an approximately 400-fold reduction in the x-ray dose, compared with conventional absorption-based tomography, without a loss in the imaging quality. The results of this study confirm and quantify the significant potential benefits achievable in three-dimensional mammography using x-ray phase-contrast imaging and phase-retrieval techniques. (paper)

  8. Low temperature thermodynamic investigation of the phase diagram of Sr3Ru2O7

    Science.gov (United States)

    Sun, D.; Rost, A. W.; Perry, R. S.; Mackenzie, A. P.; Brando, M.

    2018-03-01

    We studied the phase diagram of Sr3Ru2O7 by means of heat capacity and magnetocaloric effect measurements at temperatures as low as 0.06 K and fields up to 12 T. We confirm the presence of a new quantum critical point at 7.5 T which is characterized by a strong non-Fermi-liquid behavior of the electronic specific heat coefficient Δ C /T ˜-logT over more than a decade in temperature, placing strong constraints on theories of its criticality. In particular logarithmic corrections are found when the dimension d is equal to the dynamic critical exponent z , in contrast to the conclusion of a two-dimensional metamagnetic quantum critical end point, recently proposed. Moreover, we achieved a clear determination of the new second thermodynamic phase adjoining the first one at lower temperatures. Its thermodynamic features differ significantly from those of the dominant phase and characteristics expected of classical equilibrium phase transitions are not observed, indicating fundamental differences in the phase formation.

  9. Experimental investigation of ion cyclotron range of frequencies heating scenarios for ITER's half-field hydrogen phase performed in JET

    NARCIS (Netherlands)

    Lerche, E.; Van Eester, D.; Johnson, T. J.; Hellsten, T.; Ongena, J.; Mayoral, M. L.; Frigione, D.; Sozzi, C.; Calabro, G.; Lennholm, M.; Beaumont, P.; Blackman, T.; Brennan, D.; Brett, A.; Cecconello, M.; Coffey, I.; Coyne, A.; Crombe, K.; Czarnecka, A.; Felton, R.; Giroud, C.; Gorini, G.; Hellesen, C.; Jacquet, P.; Kiptily, V.; Knipe, S.; Krasilnikov, A.; Maslov, M.; Monakhov, I.; Noble, C.; Nocente, M.; Pangioni, L.; Proverbio, I.; Sergienko, G.; Stamp, M.; Studholme, W.; Tardocchi, M.; Vdovin, V.; Versloot, T.; Voitsekhovitch, I.; Whitehurst, A.; Wooldridge, E.; Zoita, V.; JET-EFDA Contributors,

    2012-01-01

    Two ion cyclotron range of frequencies (ICRF) heating schemes proposed for the half-field operation phase of ITER in hydrogen plasmas—fundamental H majority and second harmonic 3 He ICRF heating—were recently investigated in JET. Although the same magnetic field and RF frequencies ( f ≈ 42 MHz and f

  10. Heat transfer characteristics of thermal energy storage of a composite phase change materials: Numerical and experimental investigations

    International Nuclear Information System (INIS)

    Aadmi, Moussa; Karkri, Mustapha; El Hammouti, Mimoun

    2014-01-01

    In the present study, phase change materials based on epoxy resin paraffin wax with the melting point 27 °C were used as a new energy storage system. Thermophysical properties and the process of melting of a PCM (phase change material) composite were investigated numerically and experimentally. DSC (differential scanning calorimetry) has been used for measurement of melting enthalpy and determination of PCM heat capacity. The thermophysical properties of the prepared composite have been characterized by using a new transient hot plate apparatus. The results have shown that the most important thermal properties of these composites at the solid and liquid states are like the “apparent” thermal conductivity, the heat storage capacity and the latent heat of fusion. These experimental results have been simulated by using numerical Comsol ® Multiphysiques 4.3 based models with success. The results of the experimental investigation compare favorably with the numerical results and thus serve to validate the numerical approach. - Highlights: • Phase change materials based on paraffin spheres used as new energy storage system. • Thermophysical properties and the melting process of composites were investigated. • All experimental results have been simulated using Comsol ® Multiphysiques. • The ability to store and release the thermal energy were investigated. • A very thin molten PCM (phase change material) exists which is apparently visible in the spheres

  11. Investigation of the critical scattering at the structural phase transition in RbCaF/sub 3/ using Moessbauer diffraction

    Energy Technology Data Exchange (ETDEWEB)

    Maetz, J; Butt, N M; Jex, H; Muellner, M [Frankfurt Univ. (Germany, F.R.). Inst. fuer Kernphysik

    1979-01-01

    The critical scattering near the phase transition of RbCaF/sub 3/ from its cubic to the tetragonal structure at Tsub(c)=196 K is investigated. Moessbauer diffraction is applied to separate elastic and inelastic scattering intensities with energy resolution of 60 neV. The influence of domains is shown from X-ray diffraction.

  12. Investigation of the potential of wind energy applications in the Sct. Petersburg region. Pre-feasibility study report. Phase 1

    International Nuclear Information System (INIS)

    1995-11-01

    It was proposed to initiate an investigation and, if found to be viable, a feasibility study of the possibilities for partly substituting and supplementing the existing nuclear and fossil fuel based energy supply of the St. Petersburg region with environmentally benign wind energy. The feasibility study is expected to lead to one or more pilot projects. The proposal outlines a three-phased project including an investigation, a feasibility study and a full scale demonstration of wind energy in this region. A 4th phase is envisaged, and this will include the large scale introduction of wind energy applications using national and international financing and resulting in increased local production. The report covers the first phase, the investigation which includes data acquisition and desk studies. It is shown that technically exploitable wind potential exists in the St. Petersburg region, that local production of wind turbine equipment will reduce wind turbine costs due to decreased transport costs and lower local salaries, that suitable sites for the demonstration of both grid-connected wind farms and wind-diesel systems have been preliminarily identified and that the demonstration plants investigated have exhibited reasonable economic parameters - IRR in the range of 9 - 15%. But a feasibility study phase (2) including engineering and economic analyses must be carried out in order to reach the necessary detailed understanding of the technical and economic implications of full scale demonstration projects. (EG)

  13. The dehydration of SrTeO3(H2O)--a topotactic reaction for preparation of the new metastable strontium oxotellurate(IV) phase ε-SrTeO3.

    Science.gov (United States)

    Stöger, Berthold; Weil, Matthias; Baran, Enrique J; González-Baró, Ana C; Malo, Sylvie; Rueff, Jean Michel; Petit, Sebastien; Lepetit, Marie Bernadette; Raveau, Bernard; Barrier, Nicolas

    2011-05-28

    Microcrystalline single-phase strontium oxotellurate(IV) monohydrate, SrTeO(3)(H(2)O), was obtained by microwave-assisted hydrothermal synthesis under alkaline conditions at 180 °C for 30 min. A temperature of 220 °C and longer reaction times led to single crystal growth of this material. The crystal structure of SrTeO(3)(H(2)O) was determined from single crystal X-ray diffraction data: P2(1)/c, Z = 4, a = 7.7669(5), b = 7.1739(4), c = 8.3311(5) Å, β = 107.210(1)°, V = 443.42(5) Å(3), 1403 structure factors, 63 parameters, R[F(2)>2σ(F(2))] = 0.0208, wR(F(2) all) = 0.0516, S = 1.031. SrTeO(3)(H(2)O) is isotypic with the homologous BaTeO(3)(H(2)O) and is characterised by a layered assembly parallel to (100) of edge-sharing [SrO(6)(H(2)O)] polyhedra capped on each side of the layer by trigonal-prismatic [TeO(3)] units. The cohesion of the structure is accomplished by moderate O-H···O hydrogen bonding interactions between donor water molecules and acceptor O atoms of adjacent layers. In a topochemical reaction, SrTeO(3)(H(2)O) condensates above 150 °C to the metastable phase ε-SrTeO(3) and transforms upon further heating to δ-SrTeO(3). The crystal structure of ε-SrTeO(3), the fifth known polymorph of this composition, was determined from combined electron microscopy and laboratory X-ray powder diffraction studies: P2(1)/c, Z = 4, a = 6.7759(1), b = 7.2188(1), c = 8.6773(2) Å, β = 126.4980(7)°, V = 341.20(18) Å(3), R(Fobs) = 0.0166, R(Bobs) = 0.0318, Rwp = 0.0733, Goof = 1.38. The structure of ε-SrTeO(3) shows the same basic set-up as SrTeO(3)(H(2)O), but the layered arrangement of the hydrous phase transforms into a framework structure after elimination of water. The structural studies of SrTeO(3)(H(2)O) and ε-SrTeO(3) are complemented by thermal analysis and vibrational spectroscopic measurements.

  14. Contribution to the investigation of phase transitions induced by irradiation in insulating crystalline ceramics

    International Nuclear Information System (INIS)

    Simeone, D.

    2003-01-01

    The author gives a rather detailed overview of his research activities on the behaviour of ceramics subjected to irradiations by charged or not-charged particles. He reports the development of a new application of low incidence X ray diffraction to assess the evolutions within irradiated solids. Coupling this technique with Raman spectroscopy studies enabled the monitoring of order parameter evolution in these solids. He shows that, in some oxides, irradiation effects entail order-disorder type transitions and, more surprisingly, displacive phase transitions. From this experimental work, he developed a modelling of these phase transitions induced by irradiation. Quantitative data obtained on the evolutions of order parameters enabled these phase transitions to be explained within the frame of the thermodynamics of off-equilibrium phenomena

  15. Experimental investigation of zero phase shift effects for Coriolis flowmeters due to pipe imperfections

    DEFF Research Database (Denmark)

    Enz, Stephanie; Thomsen, Jon Juel; Neumeyer, Stefan

    2011-01-01

    mass as well as temperature changes could be causes contributing to a time-varying measured zero shift, as observed with some commercial CFMs. The conducted experimental tests of the theoretically based hypotheses have shown that simple mathematical models and approximate analysis allow general......, the flexural vibrations of two bent, parallel, non-fluid-conveying pipes are studied experimentally, employing an industrial CFM. Special attention has been paid on the phase shift in the case of zero mass flow, i.e. the zero shift, caused by various imperfections to the ‘‘perfect’’ CFM, i.e. non-uniform pipe...... damping and mass, and on ambient temperature changes. Experimental observations confirm the hypothesis that asymmetry in the axial distribution of damping will induce zero shifts similar to the phase shifts due to fluid flow. Axially symmetrically distributed damping was observed to influence phase shift...

  16. Investigation of solid-phase hydrogenation of amino acids and peptides

    International Nuclear Information System (INIS)

    Zolotarev, Yu.A.; Myasoedov, N.F.; Zajtsev, D.A.; Lubnin, M.Yu.; Tatur, V.Yu.; Kozik, V.S.; Dorokhova, E.M.; Rozenberg, S.N.

    1990-01-01

    The possibility of synthesizing amino acids and peptides multiply labelled with tritium or deuterium by the method of solid-phase isotopic exchange with gaseous hydrogen isotopes was verified. Establishment of the isotopic hydrogen equilibrium between the gaseous phase and the solid phase formed by the amino acid molecules was found experimentally. The activation energy of the isotopic exchange is 13 kcal/mol. A mathematical model was set up for the isotopic exchange with a probable substitution of hydrogen atoms. Uniformly labelled amino acids were obtained in a high optical purity and with 80 to 90% hydrogen substitution by deuterium and tritium. Tritiated peptides were prepared in high yields at molar activities of 1.5 to 3.7 TBq/mmol. (author). 4 tabs

  17. Poly(butylene terephthalate) based novel achiral stationary phase investigated under supercritical fluid chromatography conditions.

    Science.gov (United States)

    Nagai, Kanji; Shibata, Tohru; Shinkura, Satoshi; Ohnishi, Atsushi

    2018-05-11

    Poly(butylene terephthalate) based novel stationary phase (SP), composed of planar aromatic phenyl group together with ester group monomer units, was designed for supercritical fluid chromatography (SFC) use. As expected from its structure, this phase shows planarity recognition of isomeric aromatics and closely similar compounds. Interestingly, for most analytes, the retention behavior of this SP is significantly distinct from that of the 2-ethylpyridine based SPs which is among the most well-known SFC dedicated phases. Although the poly(butylene terephthalate) is coated on silica gel, the performance of the column did not change by using extended range modifiers such as THF, dichloromethane or ethyl acetate and column robustness was confirmed by cycle durability testing. Copyright © 2018 The Authors. Published by Elsevier B.V. All rights reserved.

  18. Structural investigation of the spinel phase formed in fuel CRUD before and after zinc injection

    International Nuclear Information System (INIS)

    Chen, J.

    2002-01-01

    Spinel phase is an important constituent of fuel CRUD. Since it can accommodate 60 Co in its crystal structure, its stability in reactor water environment is crucial for the radioactivity control in LWR plants. With increasing curiosity about zinc injection technology, the mechanism of the interaction of zinc with the spinel has drawn much attention. This paper describes the crystal and microstructures of spinel phase in the fuel CRUD collected on four fuel rods of 1- and 5-cycle, respectively, from Barsebaeck 2 BWR before and after zinc injection operation. High precision X-ray powder diffraction technique has been applied to identify the phase compositions of fuel CRUD and to measure the cell length of the spinel phase formed. The results show that, after about 1-cycle zinc injection operation, the tenacious CRUD formed on the fresh fuel rod contains defective zinc oxide, in addition to hematite and spinel as commonly seen. Moreover, the phase ratio of spinel to hematite is much increased. The cell length of the spinel is increased accordingly, which is the direct evidence for the presence of zinc in the spinel structure. For the 5-cycle rod, however, neither zinc oxide nor any change in the phase ratio has been detected. The cell length of the spinel has been increased, in a less degree, however, as compared to that for the 1-cycle rod. The cell lengths of spinel are similar in both tenacious and loose CRUD layers, indicating that zinc was able to easily penetrate through the tenacious CRUD layer. (authors)

  19. Liquid chromatographic studies on the behaviour of Pu(III), Pu(IV) and Pu(VI) on a RP stationary phase in presence of α-hydroxyisobutyric acid as a chelating agent

    Energy Technology Data Exchange (ETDEWEB)

    Jaison, P.G.; Kumar, Pranaw; Telmore, Vijay M. [Bhabha Atomic Research Centre, Mumbai (India). Fuel Chemistry Division

    2017-06-01

    Since plutonium possesses multiple oxidation states which can coexist in solution, a method for the identification of these oxidation states is important to understand its chemical processes. Liquid chromatographic studies were carried out to compare the chromatographic behaviour of different oxidation states of Pu in presence of the eluent, α-hydroxyisobutyric acid (HIBA). The three oxidation states of Pu viz. Pu(III), Pu(IV) and Pu(VI) were separated under optimised conditions. It was seen that the presence of the complexing agent influences the equilibrium of Pu(III)/(IV) as well as Pu(IV)/(VI) systems. Pu(III) to Pu(IV) conversion was found to be enhanced by high pH and concentration of HIBA whereas a relatively low pH and high concentration of HIBA promotes the conversion of Pu(VI) to Pu(IV).

  20. Investigation of Two-Phase Flow in Short Horizontal Mini Channel Height of 1 MM

    Directory of Open Access Journals (Sweden)

    Ron’shin Fedor

    2016-01-01

    Full Text Available The experiments with two-phase flow in the short horizontal rectangular minichannel with the height of 1 mm and width of 29 mm have been carried out using water and gas nitrogen. The five two-phase flow patterns have been recognized in the minichannel: churn, stratified, annular, bubble, and jet. These regimes are plotted on a graph and the boundaries between them determine precisely. The height of a horizontal minichannels has a significant role on boundaries between the flow regimes.

  1. Investigation on two-phase flow instability in steam generator of integrated nuclear reactor

    Institute of Scientific and Technical Information of China (English)

    1996-01-01

    In the pressure range of 3-18MPa,high pressure steam-water two-phase flow density wave instability in vertical upward parallel pipes with inner diameter of 12mm is studied experimentally.The oscillation curves of two-phase flow instability and the effects of several parameters on the oscillation threshold of the system are obtained.Based on the small pertubation linearization method and the stability principles of automatic control system,a mathematical model is developed to predict the characteristics of density wave instability threshold.The predictions of the model are in good agreement with the experimental results.

  2. Investigation of Portevin-Le Chatelier band with temporal phase analysis of speckle interferometry

    Science.gov (United States)

    Jiang, Zhenyu; Zhang, Qingchuan; Wu, Xiaoping

    2003-04-01

    A new method combining temporal phase analysis with dynamic digital speckle pattern interferometry is proposed to study Portevin-Le Chatelier effect quantitatively. The principle bases on that the phase difference of interference speckle patterns is a time-dependent function related to the object deformation. The interference speckle patterns of specimen are recorded with high sampling rate while PLC effect occurs, and the 2D displacement map of PLC band and its width are obtained by analyzing the displacement of specimen with proposed method.

  3. Investigation of the propagation characteristics in turbulent dispersed two-phase flow

    International Nuclear Information System (INIS)

    Sami, S.M.

    1980-01-01

    The propagation characteristics of turbulent dispersed two-phase flows have been studied experimentally using the Pitot tube associated with a conical hot-film anemometer. It is found that the mixture velocity increases with decreasing volumetric mixing ratio of the air and water. The void fraction distribution shows homogeneity across the test section in the special case of fully developed boundary layer two-phase flow. An expression is obtained which relates the local mixture velocity to the local void fraction, gas and liquid densities, and volumetric gas-liquid ratio

  4. Extraction and Separation of Uranium (VI) and Thorium (IV) Using Tri-n-dodecylamine Impregnated Resins

    International Nuclear Information System (INIS)

    Metwally, E.; Saleh, A.Sh.; El-Naggar, H.A.

    2005-01-01

    Extraction of U(VI) and Th(IV) from chloride and nitrate solutions with tri-n- dodecylamine impregnated on Amberlite XAD4, was investigated. The distribution of U(VI) and Th(IV) was studied at different concentrations of acid, salting-out agent, extractant, aqueous metal ion and other parameters. Absorption spectral studies have been investigated for uranium species in both aqueous HCl solution and the resin phase. From these studies, it is suggested that the tetrachloro complex of U(VI) is formed in the extraction of uranium (VI) from hydrochloric acid solutions by TDA impregnated resin. Stripping of the extracted U(VI) and Th(IV) was assayed with HCl and HNO 3 . Finally, the separation of uranium from thorium and fission products in HCl media was achieved

  5. High-pressure Raman investigations of phase transformations in pentaerythritol (C(CH sub 2 OH) sub 4)

    CERN Document Server

    Bhattacharya, T

    2002-01-01

    Our high-pressure Raman scattering experiments on pentaerythritol (C(CH sub 2 OH) sub 4) show that this compound undergoes at least three phase transformations up to 25 GPa. Splitting of various modes at approx 6.3, approx 8.2 and 10 GPa suggests that these phase transformations result in lowering of crystalline symmetry. A very small discontinuous change in slope of most of the Raman-active modes is observed at 0.3 GPa. However, no other signature of a phase transition was observed at this pressure. The observed correlation of the pressures for the onset of the two phase transformations with the limiting values of the distances between various non-bonded atoms in the parent phase suggests that the molecular rearrangements across the phase transformations are not very drastic. In addition, our earlier Fourier transform infrared and present Raman investigations indicate that high-pressure compression leads to increase in strength of the hydrogen bond present in this compound.

  6. Investigation of phase stability in the scandia-zirconia; Investigacao da estabilidade de fases da zirconia-escandia

    Energy Technology Data Exchange (ETDEWEB)

    Grosso, Robson Lopes

    2016-11-01

    In this work, the phase stability of scandia-zirconia (ScSZ) system was investigated by the thermodynamic study of nanoparticles, within the range of 0 to 20 mol% Sc{sub 2}O{sub 3}, and by codoping of ZrO{sub 2}-10 mol% Sc{sub 2}O{sub 3} (10ScSZ) with Dy{sub 2}O{sub 3} and Nb{sub 2}O{sub 5}. The phase stability of ScSZ was evaluated based on thermodynamic data collected by water adsorption microcalorimetry and high temperature oxide melt solution. Nanostructured zirconia-scandia solid solutions were synthesized by coprecipitation method. Thermodynamic data were determined for ScSZ polymorph (monoclinic, tetragonal, cubic, rhombohedral β and γ) found by X-ray diffraction. This systemic work resulted in an unprecedented phase diagram at the nanoscale of particle size-composition. The effects of additives on 10ScSZ were investigated aiming to stabilize the cubic (c) structure at room temperature and to suppress the characteristic cubic-rhombohedral β phase transformation. Compositions were prepared by coprecipitation and solid state reaction. Materials were sintered by conventional and spark plasma sintering. Full stabilization of the cubic phase was attained by 1 mol% Dy{sub 2}O{sub 3} and 0.5 mol% Nb{sub 2}O{sub 5} additions. The smallest Nb{sub 2}O{sub 5} content required for cubic phase stabilization was attributed to liquid phase formation during sintering and to small ionic radius of Nb{sup 5+}. Results of high temperature X-ray diffraction and thermal analysis show suppression of the c-β transformation. Samples containing 0.5 mol% Nb{sub 2}O{sub 5} show total ionic conductivity similar to 10ScSZ without additives within a broad temperature range with high stability during 170 h at 600 °C. (author)

  7. High-pressure fluid-phase equilibria: Experimental methods and systems investigated (2000-2004)

    DEFF Research Database (Denmark)

    Dohrn, Ralf; Peper, Stephanie; Fonseca, José

    2010-01-01

    As a part of a series of reviews, a compilation of systems for which high-pressure phase-equilibrium data were published between 2000 and 2004 is given. Vapor-liquid equilibria, liquid-liquid equilibria, vapor-liquid-liquid equilibria,solid-liquid equilibria, solid-vapor equilibria, solid-vapor-l...

  8. Investigation of the neutron production phases of a large plasma focus device

    International Nuclear Information System (INIS)

    Hayd, A.; Maurer, M.; Meinke, P.; Herold, H.; Bertalot, L.; Deutsch, R.; Grauf, W.; Jaeger, U.; Kaeppeler, H.J.; Lepper, F.; Oppenlaender, T.; Schmidt, H.; Schmidt, R.; Schwarz, J.; Schwoerer, K.; Shakhatre, M.

    1982-09-01

    Plasma dynamic behavior and neutron production in large focus devices with pinch currents of approximately 1 MA have been studied with theoretical as well as experimental methods. For treating turbulent plasma motion, a hybrid code based on the analytical computer algorithm REDUCE was developed. Experimental diagnostics include schlieren photographs, reaction proton localization with pinhole cameras and neutron measurements with Ag-counters and scintillators. Calculated and measured data concern the 280 kJ, 60 kV operational mode of the POSEIDON plasma focus. It is shown that for large pinch currents ( > 500 kA), neutron emission also appears before m = 0 onset in the intermediate phase. This part of the neutron production becomes predominant for very large currents. The lifetime of this intermediate phase strongly increases with increasing current. According to theory, the late phase of the focus is governed by strong turbulence phenomena. The lifetime of the turbulence packets is approximately 150 ns and seems to explain the long lasting neutron emission in this phase. (orig.)

  9. An experimental investigation of pure-substance, adiabatic two-phase flow in a vertical pipe

    International Nuclear Information System (INIS)

    Nikitopoulos, D.E.; Maeder, P.F.

    1994-01-01

    Two-phase flows of pure substances are of particular importance for a wide range of applications in the thermo-hydraulic components of nuclear power generations systems, heat exchangers, geothermal wells, refrigeration systems, etc. Measurements of pressure drop, temperature, and average void fraction are presented for adiabatic, vertical-upwards, two-phase flow of Refrigerant 114 in a pipe. An experimental method has been developed according to which the evolution of flow states occurring in long pipes can be realized in a test section of limited length. The experiments cover the range of the flow from flashing to near choking. The measurements indicate existence of macroscopic thermodynamic equilibrium, except in the immediate neighborhood of flashing. Compressibility due to phase change is shown to play a very important role in the development of the flow. Three regions are recognized based on the measured energetics of the flow. Each region is dominated by potential energy changes, dissipation, and kinetic energy changes, respectively. The evolution of the flow is governed by hydrostatic effects in the initial region after flashing and by high, phase-change-induced kinetic energy increases far downstream as the flow approaches choking. In the intermediate region, viscous, inertial and gravitational effects play a role of comparable importance. The interfacial and wall shear forces have also been calculated from the measurements. The former dominate the initial regions of the flow, while the latter are strongest at high vapor contents

  10. Investigating the Retention Mechanisms of Liquid Chromatography Using Solid-Phase Extraction Cartridges

    Science.gov (United States)

    O'Donnell, Mary E.; Musial, Beata A.; Bretz, Stacey Lowery; Danielson, Neil D.; Ca, Diep

    2009-01-01

    Liquid chromatography (LC) experiments for the undergraduate analytical laboratory course often illustrate the application of reversed-phase LC to solve a separation problem, but rarely compare LC retention mechanisms. In addition, a high-performance liquid chromatography instrument may be beyond what some small colleges can purchase. Solid-phase…

  11. Protection and thermal management of thermoelectric generator system using phase change materials: An experimental investigation

    DEFF Research Database (Denmark)

    Ahmadi Atouei, Saeed; Rezaniakolaei, Alireza; Ranjbar, A.A.

    2018-01-01

    In most thermoelectric systems the thermal boundary conditions are transient, and thermal manage-ment of the system is critical to improve electrical performance of the system. In this study, effect of using phase change materials (PCM) to control the hot and cold side temperatures...

  12. DSC and X-ray diffraction investigations of phase transitions in HxBABA and NBABA

    International Nuclear Information System (INIS)

    Usha Deniz, K.; Paranjpe, A.S.; Mirza, E.B.; Parvathanathan, P.S.; Patel, K.S.

    1979-01-01

    The phase transitions and the heats of transformation, of the hexyl (HxBABA) and nonyl (NBABA) members of the series of compounds, p-n-Alkoxybenzylidene-p-Aminobenzoic Acids, have been studied by DSC in the temperature range, - 100 0 C to 300 0 C. A scheme of transitions has been proposed for each of the compounds. X-ray diffraction measurements have been done in the smectic C(Ssub(c)) and nematic (N) phases of these materials. The results reveal that (1) the Ssub(c) phase in both compounds is of the C 1 -type, (2) Ssub(c)-type order is seen throughout the nematic phase in HxBABA, whereas in NBABA, it is seen only in the neighbourhood of the Ssub(c)-N transition, (3) the temperature dependence of the smectic layer thickness, d, and of the directly measured tilt angle, theta sub(t,d), reflect faithfully the strength of the first order transition, Ssub(c)-N, and (4) there is a marked difference between the values and the temperature variations of theta sub(t,d) and theta sub(t,c) (tilt angle calculated from d) which is not completely understood, at present

  13. Final Report: Investigations of Mixed-Phase Cloud Microphysical, Radiative, and Dynamical Processes

    Energy Technology Data Exchange (ETDEWEB)

    Shupe, Matthew [Univ. of Colorado, Boulder, CO (United States)

    2016-08-18

    This project supported the principle investigator’s work on a number of studies regarding mixed-phase clouds and in various related collaborations with ARM and related scientists. This project has contributed to numerous publications and conference/meeting presentations.

  14. An experimental investigation of stratified two-phase pipe flow at small inclinations

    Energy Technology Data Exchange (ETDEWEB)

    Espedal, Mikal

    1998-12-31

    The prediction of stratified flow is important for several industrial applications. Stratified flow experiments were carefully performed in order to investigate the performance of a typical model which uses wall friction factors based on single phase pipe flow as described above. The test facility has a 18.5 m long and 60 mm i.d. (L/D=300) acrylic test section which can be inclined between -10 {sup o} and +10 {sup o}. The liquid holdup was measured by using fast closing valves and the pressure gradients by using three differential pressure transducers. Interfacial waves were measured by thin wire conductance probes mounted in a plane perpendicular to the main flow. The experiments were performed using water and air at atmospheric pressure. The selected test section inclinations were between -3 {sup o} and +0.5 {sup o} to the horizontal plane. A large number of experiments were performed for different combinations of air and water flow rates and the rates were limited to avoid slug flow and stratified flow with liquid droplets. The pressure gradient and the liquid holdup were measured. In addition the wave probes were used to find the wave heights and the wave power spectra. The results show that the predicted pressure gradient using the standard models is approximately 30% lower than the measured value when large amplitude waves are present. When the flow is driven by the interfacial force the test section inclination has minor influence on the deviation between predicted and measured pressure gradients. Similar trends are apparent in data from the literature, although they seem to have gone unnoticed. For several data sets large spread in the predictions are observed when the model described above was used. Gas wall shear stress experiments indicate that the main cause of the deviation between measured and predicted pressure gradient and holdup resides in the modelling of the liquid wall friction term. Measurements of the liquid wall shear stress distribution

  15. A 4-year non-randomized comparative phase-IV study of early rheumatoid arthritis: integrative anthroposophic medicine for patients with preference against DMARDs versus conventional therapy including DMARDs for patients without preference

    Directory of Open Access Journals (Sweden)

    Hamre HJ

    2018-03-01

    Full Text Available Harald J Hamre,1 Van N Pham,2 Christian Kern,3 Rolf Rau,4 Jörn Klasen,3 Ute Schendel,5 Lars Gerlach,6 Attyla Drabik,2 Ludger Simon6,† 1Institute for Applied Epistemology and Medical Methodology at the Witten/Herdecke University, Freiburg, Germany; 2Institute of Statistics in Medicine, Universitätsklinikum Düsseldorf, Düsseldorf, Germany; 3Department of Integrative Medicine, Asklepios Westklinikum, Hamburg, Germany; 4Department of Rheumatology, Evangelisches Fachkrankenhaus Ratingen, Ratingen, Germany; 5Department of Rheumatology, m&i-Fachklinik Bad Pyrmont, Bad Pyrmont, Germany; 6Department of Internal Medicine and Gastroenterology, Filderklinik, Filderstadt, Germany †Dr Ludger Simon passed away on June 10, 2016 Background: While disease-modifying antirheumatic drugs (DMARDs are a mainstay of therapy for rheumatoid arthritis (RA, some patients with early RA refuse DMARDs. In anthroposophic medicine (AM, a treatment strategy for early RA without DMARDs has been developed. Preliminary data suggest that RA symptoms and inflammatory markers can be reduced under AM, without DMARDs. Patients and methods: Two hundred and fifty-one self-selected patients aged 16–70 years, starting treatment for RA of <3 years duration, without prior DMARD therapy, participated in a prospective, non-randomized, comparative Phase IV study. C-patients were treated in clinics offering conventional therapy including DMARDs, while A-patients had chosen treatment in anthroposophic clinics, without DMARDs. Both groups received corticosteroids and nonsteroidal anti-inflammatory drugs (NSAIDs. Primary outcomes were intensity of RA symptoms measured by self-rating on visual analog scales, C-reactive protein, radiological progression, study withdrawals, serious adverse events (SAE, and adverse drug reactions in months 0–48. Results: The groups were similar in most baseline characteristics, while A-patients had longer disease duration (mean 15.1 vs 10.8 months, p<0

  16. Effectiveness and safety of silodosin in the treatment of lower urinary tract symptoms in patients with benign prostatic hyperplasia: A European phase IV clinical study (SiRE study).

    Science.gov (United States)

    Montorsi, Francesco; Gandaglia, Giorgio; Chapple, Christopher; Cruz, Francisco; Desgrandchamps, Francois; Llorente, Carlos

    2016-07-01

    To assess the benefit-risk balance of silodosin in a real-life setting of benign prostatic hyperplasia patients with lower urinary tract symptoms. A phase IV trial including men aged ≥60 years with a clinical diagnosis of benign prostatic hyperplasia with an International Prostate Symptom Score ≥12 was carried out. Patients received silodosin 8 mg for 24 weeks. The primary end-point was a decrease ≥25% in the total International Prostate Symptom Score. Secondary end-points were: changes in total, storage and voiding, and quality of life International Prostate Symptom Scores; changes in the International Continence Society-male questionnaire; changes in the frequency/volume chart; and satisfaction according to the Patient Perception of Study Medication questionnaire. Treatment-emergent adverse events were recorded. Overall, 1036 patients were enrolled. Of these, 766 patients (77.1%) had a decrease ≥25% in the total International Prostate Symptom Score. The mean total International Prostate Symptom Score, and storage and voiding symptoms subscores decreased from 18.9, 8.1 and 10.8 to 10.6, 4.9 and 5.7. Nocturia decreased from 85.7% to 52.4%. The mean International Prostate Symptom Score quality of life score decreased from 4.0 to 2.2. Half of the patients reported an improvement in the frequency and bothersomeness of the most frequent symptoms reported at baseline (all P Silodosin improved lower urinary tract symptoms in three out of four patients, including diurnal voiding and storage symptoms, nocturia, and quality of life. This treatment showed a favorable safety profile in this setting. © 2016 The Japanese Urological Association.

  17. Comparison of the safety and immunogenicity of live attenuated and inactivated hepatitis A vaccine in healthy Chinese children aged 18 months to 16 years: results from a randomized, parallel controlled, phase IV study.

    Science.gov (United States)

    Ma, F; Yang, J; Kang, G; Sun, Q; Lu, P; Zhao, Y; Wang, Z; Luo, J; Wang, Z

    2016-09-01

    For large-scale immunization of children with hepatitis A (HA) vaccines in China, accurately designed studies comparing the safety and immunogenicity of the live attenuated HA vaccine (HA-L) and inactivated HA vaccine (HA-I) are necessary. A randomized, parallel controlled, phase IV clinical trial was conducted with 6000 healthy children aged 18 months to 16 years. HA-L or HA-I was administered at a ratio of 1: 1 to randomized selected participants. The safety and immunogenicity were evaluated. Both HA-L and HA-I were well tolerated by all participants. The immunogenicity results showed that the seroconversion rates (HA-L versus HA-I: 98.0% versus 100%, respectively, p >0.05), and geometric mean concentrations in participants negative for antibodies against HA virus IgG (anti-HAV IgG) before vaccination did not differ significantly between the two types of vaccines (HA-L versus HA-I first dose: 898.9 versus 886.2 mIU/mL, respectively, p >0.05). After administration of the booster dose of HA-I, the geometric mean concentrations of anti-HAV IgG (HA-I booster dose: 2591.2 mIU/mL) was higher than that after the first dose (p children. The effects of long-term immunogenicity after natural exposure to wild-type HA virus and the possibility of mutational shifts of the live vaccine virus in the field need to be studied in more detail. Copyright © 2016. Published by Elsevier Ltd.

  18. Induction therapy with cetuximab plus docetaxel, cisplatin, and 5-fluorouracil (ETPF) in patients with resectable nonmetastatic stage III or IV squamous cell carcinoma of the oropharynx. A GERCOR phase II ECHO-07 study

    International Nuclear Information System (INIS)

    Chibaudel, Benoist; Lacave, Roger; Lefevre, Marine; Soussan, Patrick; Antoine, Martine; Périé, Sophie; Belloc, Jean-Baptiste; Banal, Alain; Albert, Sébastien; Chabolle, Frédéric; Céruse, Philippe; Baril, Philippe; Gatineau, Michel; Housset, Martin; Moukoko, Rachel; Benetkiewicz, Magdalena; Gramont, Aimery de; Bonnetain, Franck; Lacau St Guily, Jean

    2015-01-01

    Induction TPF regimen is a standard treatment option for squamous cell carcinoma (SCC) of the oropharynx. The efficacy and safety of adding cetuximab to induction TPF (ETPF) therapy was evaluated. Patients with nonmetastatic resectable stage III/IV SCC of the oropharynx were treated with weekly cetuximab followed the same day by docetaxel and cisplatin and by a continuous infusion of 5-fluorouracil on days 1-5 (every 3 weeks, 3 cycles). The primary endpoint was clinical and radiological complete response (crCR) of primary tumor at 3 months. Secondary endpoints were crCR rates, overall response, pathological CR, progression-free survival, overall survival, and safety. Forty-two patients were enrolled, and 41 received ETPF. The all nine planned cetuximab doses and the full three doses of planned chemotherapy were completed in 31 (76%) and 36 (88%) patients, respectively. Twelve (29%) patients required dose reduction. The crCR of primary tumor at the completion of therapy was observed in nine (22%) patients. ETPF was associated with a tumor objective response rate (ORR) of 58%. The most frequent grade 3–4 toxicities were as follows: nonfebrile neutropenia (39%), febrile neutropenia (19%), diarrhea (10%), and stomatitis (12%). Eighteen (44%) patients experienced acne-like skin reactions of any grade. One toxic death occurred secondary to chemotherapy-induced colitis with colonic perforation. This phase II study reports an interesting response rate for ETPF in patients with moderately advanced SCC of the oropharynx. The schedule of ETPF evaluated in this study cannot be recommended at this dosage

  19. Investigation of shape memory of red blood cells using optical tweezers and quantitative phase microscopy

    Science.gov (United States)

    Cardenas, Nelson; Mohanty, Samarendra K.

    2012-03-01

    RBC has been shown to possess shape memory subsequent to shear-induced shape transformation. However, this property of RBC may not be generalized to all kinds of stresses. Here, we report our observation on the action of radiation pressure forces on RBC's shape memory using optical manipulation and quantitative phase microscopy (OMQPM). QPM, based on Mach-Zehnder interferrometry, allowed measurement of dynamic changes of shape of RBC in optical tweezers at different trapping laser powers. In high power near-infrared optical tweezers (>200mW), the RBC was found to deform significantly due to optical forces. Upon removal of the tweezers, hysteresis in recovering its original resting shape was observed. In very high power tweezers or long-term stretching events, shape memory was almost erased. This irreversibility of the deformation may be due to temperature rise or stress-induced phase transformation of lipids in RBC membrane.

  20. Gas-phase infrared spectrum of phosphorus (III) oxycyanide, OPCN: experimental and theoretical investigations

    Science.gov (United States)

    Allaf, Abdul. W.; Kassem, M.; Alibrahim, M.; Boustani, Ihsan

    1999-03-01

    An attempt was made to observe the gas-phase infrared spectrum of Phosphorus (III) oxycyanide, OPCN for the first time. This molecule was produced by an on-line process using phosphorus (III) oxychloride, OPCl as precursor passed over heated AgCN. The products were characterised by the infrared spectra of their vapours. The low resolution gas-phase Fourier transform infrared spectrum shows two bands centered at 2165 and 1385 cm -1. These bands are assigned to, ν1 (CN stretch) and ν2 (OP stretch), respectively. Ab initio self-consistent-field (SCF) molecular orbital (MO) and Møller-Plesset second order perturbation theory (MP2) calculations were performed to determine the geometry, total energy and vibrational frequencies of OPCN.

  1. Gas-phase infrared spectrum of phosphorus (III) oxycyanide, OPCN: Experimental and theoretical and theoretical investigations

    International Nuclear Information System (INIS)

    Allaf, A.W.; Kassem, M.; Alibrahim, M.

    1999-01-01

    An attempt was made to observe the gas-phase infrared spectrum of phosphorus (III) oxycyanide, OPCN for the first time. This molecule was produced by on-line process using phosphorus (III) oxychloride, OPCI as precursor passed over heated Ag CN. The products were characterised by the infrared spectra of their vapours. The low resolution gas-phase Fourier transform infrared spectrum shows two bands at 2165 and 1385 cm -1 . These bands are assigned to ν 1 (C≡N stretch) and ν 2 (O=P stretch), respectively. Ab initio self-consistent-field (SCF) molecular orbital (MO) and Moeller - Plesset second order perturbation theory (MP2) calculations were performed to determine the geometry, total energy and vibrational frequencies of OPCN. (authors)

  2. Three-dimensional investigation of the two-phase flow structure in a bubbly pipe flow

    International Nuclear Information System (INIS)

    Schmidl, W.; Hassan, Y.A.; Ortiz-Villafuerte, J.

    1996-01-01

    Particle image velocimetry (PIV) is a nonintrusive measurement technique that can be used to study the structure of various fluid flows. PIV is used to measure the time-varying, full-field velocity data of a particle-seeded flow field within either a two-dimensional plane or three-dimensional volume. PIV is a very efficient measurement technique since it can obtain both qualitative and quantitative spatial information about the flow field being studied. The quantitative spatial velocity information can be further processed into information of flow parameters such as vorticity and turbulence over extended areas. The objective of this study was to apply recent advances and improvements in the PIV flow measurement technique to the full-field, nonintrusive analysis of a three-dimensional, two-phase fluid flow system in such a manner that both components of the two-phase system could be experimentally quantified

  3. An experimental and numerical investigation of crossflow effects in two-phase displacements

    DEFF Research Database (Denmark)

    Cinar, Y.; Jessen, Kristian; Berenblyum, Roman

    2006-01-01

    In this paper, we present flow visualization experiments and numerical simulations that demonstrate the combined effects of viscous and capillary forces and gravity segregation on crossflow that occurs in two-phase displacements in layered porous media. We report results of a series of immiscible...... flooding experiments in 2D, two-layered glass bead models. Favorable mobility-ratio imbibition and unfavorable mobility-ratio drainage experiments were performed. We used pre-equilibrated immiscible phases from a ternary isooctane/isopropanol/water system, which allowed control of the interfacial tension....... The experiments also illustrate the complex interplay of capillary, gravity, and viscous forces that controls crossflow. The experimental results confirm that the transition ranges of scaling groups suggested by Zhou et al. (1994) are appropriate/valid. We report also results of simulations of the displacement...

  4. IV access in dental practice.

    LENUS (Irish Health Repository)

    Fitzpatrick, J J

    2009-04-01

    Intravenous (IV) access is a valuable skill for dental practitioners in emergency situations and in IV sedation. However, many people feel some apprehension about performing this procedure. This article explains the basic principles behind IV access, and the relevant anatomy and physiology, as well as giving a step-by-step guide to placing an IV cannula.

  5. Toxicity and survival results of a phase II study investigating the role of postoperative chemoradioimmunotherapy for gastric adenocarcinoma

    Energy Technology Data Exchange (ETDEWEB)

    Bese, N.S.; Yildirim, A.; Oeber, A. [Dept. of Radiation Oncology, Istanbul Univ., Cerrahpasa Medical School, Istanbul (Turkey); Bueyuekuenal, E.; Oezgueroglu, M.; Demir, G.; Mandel, N.M.; Demirelli, F.; Serdengecti, S. [Dept. of Internal Medicine, Medical Oncology Section, Istanbul Univ., Cerrahpasa Medical School, Istanbul (Turkey)

    2005-10-01

    Background and purpose: to investigate the role of postoperative concomitant chemoradioimmunotherapy in gastric adenocarcinoma patients. Patients and methods: 59 pateints, who underwent total or subtotal gastrectomy, with lymph node involvement, positive microscopic surgical margins or serosal involvement were included in the study. Radiotherapy started concomitantly with chemotherapy and levamisole. Extended-field radiotherapy was given to gastric bed and regional lymphatics via two anterior-posterior/posterior-anterior fields. A total dose of 45 Gy in 25 fractions with a fraction size of 1.8 Gy was planned. In 28 patients (48%) with positive surgical margins a 10-Gy boost dose was given to the anastomosis site. An adjuvant i.v. bolus of 450 mg/m{sup 2}/day 5-fluorouracil (5-FU) was administered concomitantly during the first 3 days and at the 20th day of irradiation. After completion of radiotherapy, i.v. boluses of 450 mg/m{sup 2}/day 5-FU and 25 mg/m{sup 2}/day rescuvorin were continued for 6 months once a week. Levamisole 40 mg/day orally was started at the 1st day of radiotherapy and also continued for 6 months. Median follow-up was 37 months (7-112 months). Results: median survival was 23 months. Overall 3- and 5-year survival rates amounted to 35% and 14%, respectively. Median survival of the patients with positive surgical margins was 22 months. The 3- and 5-year locoregional control rates were 59% and 55%, respectively. The most common toxicity was upper gastrointestinal system toxicity, which was observed in 42 patients (71%). Four patients (7%) died on account of early toxic effects, and six (10%) could not complete treatment. Conclusion: although 48% of the study population involved patients with microscopic residual disease, the survival results as a whole were satisfactory. However, due to high toxicity, radiotherapy must be delivered with the most proper techniques along with adequate nutrition and supportive care. (orig.)

  6. Docetaxel, cisplatin and 5-fluorouracil induction chemotherapy followed by chemoradiotherapy or chemoradiotherapy alone in stage III-IV unresectable head and neck cancer. Results of a randomized phase II study

    International Nuclear Information System (INIS)

    Takacsi-Nagy, Zoltan; Polgar, Csaba; Major, Tibor; Fodor, Janos; Hitre, Erika; Remenar, Eva; Kasler, Miklos; Oberna, Ferenc; Goedeny, Maria

    2015-01-01

    Concurrent chemoradiotherapy (CRT) is the standard treatment for advanced head and neck squamous cell carcinoma. In this phase II randomized study, the efficacy and toxicity of docetaxel, cisplatin and 5-fluorouracil induction chemotherapy (ICT) followed by concurrent CRT was compared with those after standard CRT alone in patients with locally advanced, unresectable head and neck cancer. Between January 2007 and June 2009, 66 patients with advanced (stage III or IV) unresectable squamous cell carcinoma of the head and neck (oral cavity, oropharynx, hypopharynx, and larynx) were randomly assigned to two groups: one receiving two cycles of docetaxel, cisplatin, and 5-fluorouracil ICT followed by CRT with three cycles of cisplatin and one treated by CRT alone. Response rate, local tumor control (LTC), locoregional tumor control (LRTC), overall survival (OS), progression-free survival (PFS), and toxicity results were assessed. Three patients from the ICT + CRT group did not appear at the first treatment, so a total of 63 patients were evaluated in the study (30 ICT + CRT group and 33 CRT group). Three patients died of febrile neutropenia after ICT. The median follow-up time for surviving patients was 63 months (range 53-82 months). The rate of radiologic complete response was 63 % following ICT + CRT, whereas 70 % after CRT alone. There were no significant differences in the 3-year rates of LTC (56 vs. 57 %), LRTC (42 vs. 50 %), OS (43 vs. 55 %), and PFS (41 vs. 50 %) in the ICT + CRT group and in the CRT group, respectively. The rate of grade 3-4 neutropenia was significantly higher in the ICT + CRT group than in the CRT group (37 and 12 %; p = 0.024). Late toxicity (grade 2 or 3 xerostomia) developed in 59 and 42 % in the ICT + CRT and CRT groups, respectively. The addition of ICT to CRT did not show any advantage in our phase II trial, while the incidence of adverse events increased. The three deaths as a consequence of ICT call attention to the importance of

  7. Investigation of Effect Additive Phase Change Materials on the Thermal Conductivity

    Science.gov (United States)

    Nakielska, Magdalena; Chalamoński, Mariusz; Pawłowski, Krzysztof

    2017-10-01

    The aim of worldwide policy is to reduce the amount of consumed energy and conventional fuels. An important branch of the economy that affects the energy balance of the country is construction industry. In Poland, since January 1st, 2017 new limit values have been valid regarding energy saving and thermal insulation of buildings. To meet the requirements of more and more stringent technical and environmental standards, new technological solutions are currently being looked for. When it comes to the use of new materials, phase-change materials are being widely introduced into construction industry. Thanks to phase-change materials, we can increase the amount of heat storage. Great thermal inertia of the building provides more stable conditions inside the rooms and allows the use of unconventional sources of energy such as solar energy. A way to reduce the energy consumption of the object is the use of modern solutions for ventilation systems. An example is the solar chimney, which supports natural ventilation in order to improve internal comfort of the rooms. Numerous studies are being carried out in order to determine the optimal construction of solar chimneys in terms of materials and construction parameters. One of the elements of solar chimneys is an absorption plate, which affects the amount of accumulated heat in the construction. In order to carry out the research on the thermal capacity of the absorption plate, the first research work has been already planned. The work presents the research results of a heat-transfer coefficient of the absorption plates samples made of cement, aggregate, water, and phase-change material in different volume percentage. The work also presents methodology and the research process of phase-change material samples.

  8. A facility for the experimental investigation of single substance two phase flow

    International Nuclear Information System (INIS)

    Maeder, P.F.; Dickinson, D.A.; Nikitopoulos, D.E.; DiPippo, R.

    1985-01-01

    The paper describes a research facility dedicated to single-substance two-phase flow. The working fluid is dichlorotetrafluoroethane (or refrigerant R-114), allowing both operation at manageable pressures, temperatures and flowrates, and application of results to practical situations through similarity. Operation is in the blowdown mode. The control and data acquisition systems are fully automated and computer controlled. A range of flow conditions from predominantly liquid flow to high velocity, high void fraction choked flow can be attained

  9. Investigation on Capacitor Switching Transient Limiter with a Three phase Variable Resistance

    DEFF Research Database (Denmark)

    Naderi, Seyed Behzad; Jafari, Mehdi; Zandnia, Amir

    2017-01-01

    In this paper, a capacitor switching transient limiter based on a three phase variable resistance is proposed. The proposed structure eliminates the capacitor switching transient current and over-voltage by introducing a variable resistance to the current path with its special switching pattern...... transients on capacitor after bypassing. Analytic Analyses for this structure in transient cases are presented in details and simulations are performed by MATLAB software to prove its effectiveness....

  10. Phase diagram, thermodynamic investigations, and modelling of systems relevant to lithium-ion batteries

    International Nuclear Information System (INIS)

    Fuertauer, Siegfried; Beutl, Alexander; Flanorfer, Hans; Henriques, David; Giel, Hans; Markus, Thorsten

    2017-01-01

    This article reports on two consecutive joint projects titled ''Experimental Thermodynamics and Phase Relations of New Electrode Materials for Lithium-Ion Batteries'', which were performed in the framework of the WenDeLIB 1473 priority program ''Materials with new Design for Lithium Ion Batteries''. Hundreds of samples were synthesized using experimental techniques specifically developed to deal with highly reactive lithium and lithium-containing compounds to generate electrochemical, phase diagram and crystal structure data in the Cu-Li, Li-Sn, Li-Sb, Cu-Li-Sn, Cu-Li-Sb and selected oxide systems. The thermochemical and phase diagram data were subsequently used to develop self-consistent thermodynamic descriptions of several binary systems. In the present contribution, the experimental techniques, working procedures, results and their relevance to the development of new electrode materials for lithium ion batteries are discussed and summarized. The collaboration between the three groups has resulted in more than fifteen (15) published articles during the six-year funding period.

  11. Phase diagram, thermodynamic investigations, and modelling of systems relevant to lithium-ion batteries

    Energy Technology Data Exchange (ETDEWEB)

    Fuertauer, Siegfried; Beutl, Alexander; Flanorfer, Hans [Vienna Univ. (Austria). Dept. of Inorganic Chemistry - Functional Materials; Li, Dajian; Cupid, Damian [Karlsruhe Institute of Technology (KIT), Eggenstein-Leopoldshafen (Germany). Inst. for Applied Materials - Applied Materials Physics (IAM-AWP); Henriques, David; Giel, Hans; Markus, Thorsten [Mannheim Univ. of Applied Sciences (Germany). Inst. for Thermo- and Fluiddynamics

    2017-11-15

    This article reports on two consecutive joint projects titled ''Experimental Thermodynamics and Phase Relations of New Electrode Materials for Lithium-Ion Batteries'', which were performed in the framework of the WenDeLIB 1473 priority program ''Materials with new Design for Lithium Ion Batteries''. Hundreds of samples were synthesized using experimental techniques specifically developed to deal with highly reactive lithium and lithium-containing compounds to generate electrochemical, phase diagram and crystal structure data in the Cu-Li, Li-Sn, Li-Sb, Cu-Li-Sn, Cu-Li-Sb and selected oxide systems. The thermochemical and phase diagram data were subsequently used to develop self-consistent thermodynamic descriptions of several binary systems. In the present contribution, the experimental techniques, working procedures, results and their relevance to the development of new electrode materials for lithium ion batteries are discussed and summarized. The collaboration between the three groups has resulted in more than fifteen (15) published articles during the six-year funding period.

  12. Experimental investigation on local parameter measurement using optical probes in two-phase flow under rolling condition

    International Nuclear Information System (INIS)

    Tian Daogui; Sun Licheng; Yan Changqi; Liu Guoqiang

    2013-01-01

    In order to get more local interfacial information as well as to further comprehend the intrinsic mechanism of two-phase flow under rolling condition, a method was proposed to measure the local parameters by using optical probes under rolling condition in this paper. An experimental investigation of two-phase flow under rolling condition was conducted using the probe fabricated by the authors. It is verified that the probe method is feasible to measure the local parameters in two'-phase flow under rolling condition. The results show that the interfacial parameters distribution near wall region has a distinct periodicity due to the rolling motion. The averaged deviation of the void fraction measured by the probe from that obtained from measured pressure drop is about 8%. (authors)

  13. Numerical Investigation on the Effects of a Precursor Wetting Film on the Displacement of Two Immiscible Phases Along a Channel

    KAUST Repository

    Bao, Kai; Salama, Amgad; Sun, Shuyu

    2015-01-01

    A set of numerical experiments has been conducted to study the effect of a precursor fluid layer on the motion of two phase system in a channel. This system is characterized by coupled Cahn-Hillard and Navier-Stokes system together with slip boundary conditions. The solution of the governing equation involves first the solution of Cahn-Hillard equation with semi-implicit and Mixed finite element discritization with a convex splitting scheme. The Navier-Stokes equations are then solved with a P2-P0 mixed finite element method. Three cases have been investigated; in the first the effect of different wettability scenarios with no precursor layer has been investigated. In the second scenario, the effect of the precursor layer for different wettability conditions is investigated. In the third case, the effect of the thickness of the precursor layer is investigated. It is found that, wettability conditions have considerable effect on the flow of the considered two-phase system. Furthermore the existence of the precursor layer has additional influence on the breakthrough of the phases.

  14. Numerical Investigation on the Effects of a Precursor Wetting Film on the Displacement of Two Immiscible Phases Along a Channel

    KAUST Repository

    Bao, Kai

    2015-10-08

    A set of numerical experiments has been conducted to study the effect of a precursor fluid layer on the motion of two phase system in a channel. This system is characterized by coupled Cahn-Hillard and Navier-Stokes system together with slip boundary conditions. The solution of the governing equation involves first the solution of Cahn-Hillard equation with semi-implicit and Mixed finite element discritization with a convex splitting scheme. The Navier-Stokes equations are then solved with a P2-P0 mixed finite element method. Three cases have been investigated; in the first the effect of different wettability scenarios with no precursor layer has been investigated. In the second scenario, the effect of the precursor layer for different wettability conditions is investigated. In the third case, the effect of the thickness of the precursor layer is investigated. It is found that, wettability conditions have considerable effect on the flow of the considered two-phase system. Furthermore the existence of the precursor layer has additional influence on the breakthrough of the phases.

  15. In situ TEM investigation on the precipitation behavior of μ phase in Ni-base single crystal superalloys

    International Nuclear Information System (INIS)

    Gao, Shuang; Liu, Zhi-Quan; Li, Cai-Fu; Zhou, Yizhou; Jin, Tao

    2016-01-01

    The precipitation behavior of μ phase in Ni-base single crystal superalloys was investigated by in situ transmission electron microscopy (TEM). A layer-by-layer growth process with a ledge propagation mechanism was first observed during in situ precipitation. Three types of μ phase with different morphologies were found, which grow along [001] μ with (001) μ planar defects, [-111] μ with (1–12) μ planar defects, as well as both directions with mixed planar defects. High-resolution TEM image and established atomic models reveal a basic growth mechanism of μ phase by stacking on (001) μ plane and randomly forming coherent planar defects, while the nucleation of incoherent (1–12) μ planar defects at the early stage of precipitation plays an important role in affecting the basic growth mechanism. The frequent faults during the stacking process of the sub-unit layers within μ lattice should be responsible for the defect formation. -- Graphical abstract: In situ transmission electron microscopy (TEM) investigations reveal the layer-by-layer growth mechanism of μ phase precipitated in Ni-base single crystal superalloys. Three types of μ phase with different morphologies were formed at 1050 °C, which grows along [001] μ with (001) μ planar defects, [-111] μ with (1–12) μ planar defects, as well as both directions with mixed planar defects respectively. Formation of (001) μ micro-twin and stacking fault is the essential feature for precipitated μ phase, while nucleation of incoherent (1–12) μ planar defects plays an important role in changing growth method. Display Omitted

  16. Internet Economics IV

    Science.gov (United States)

    2004-08-01

    edts.): Internet Economics IV Technical Report No. 2004-04, August 2004 Information Systems Laboratory IIS, Departement of Computer Science University of...level agreements (SLA), Information technology (IT), Internet address, Internet service provider 16. PRICE CODE 17. SECURITY CLASSIFICATION 18... technology and its economic impacts in the Internet world today. The second talk addresses the area of AAA protocol, summarizing authentication

  17. Uranium (IV) carboxylates - I

    Energy Technology Data Exchange (ETDEWEB)

    Satpathy, K C; Patnaik, A K [Sambalpur Univ. (India). Dept. of Chemistry

    1975-11-01

    A few uranium(IV) carboxylates with monochloro and trichloro acetic acid, glycine, malic, citric, adipic, o-toluic, anthranilic and salicylic acids have been prepared by photolytic methods. The I.R. spectra of these compounds are recorded and basing on the spectral data, structure of the compounds have been suggested.

  18. PLATO IV Accountancy Index.

    Science.gov (United States)

    Pondy, Dorothy, Comp.

    The catalog was compiled to assist instructors in planning community college and university curricula using the 48 computer-assisted accountancy lessons available on PLATO IV (Programmed Logic for Automatic Teaching Operation) for first semester accounting courses. It contains information on lesson access, lists of acceptable abbreviations for…

  19. Phase stability, mechanical properties, hardness, and possible reactive routing of chromium triboride from first-principle investigations

    International Nuclear Information System (INIS)

    Zhong, Ming-Min; Kuang, Xiao-Yu; Wang, Zhen-Hua; Shao, Peng; Ding, Li-Ping; Huang, Xiao-Fen

    2013-01-01

    The first-principles calculations are employed to provide a fundamental understanding of the structural features and relative stability, mechanical and electronic properties, and possible reactive route for chromium triboride. The predicted new phase of CrB 3 belongs to the rhombohedral phase with R-3m symmetry and it transforms into a hexagonal phase with P-6m2 symmetry at 64 GPa. The mechanical and thermodynamic stabilities of CrB 3 are verified by the calculated elastic constants and formation enthalpies. Also, the full phonon dispersion calculations confirm the dynamic stability of predicted CrB 3 . Considering the role of metallic contributions, the calculated hardness values from our semiempirical method for rhombohedral and hexagonal phases are 23.8 GPa and 22.1 GPa, respectively. In addition, the large shear moduli, Young's moduli, low Poisson's ratios, and small B/G ratios indicate that they are potential hard materials. Relative enthalpy calculations with respect to possible constituents are also investigated to assess the prospects for phase formation and an attempt at high-pressure synthesis is suggested to obtain chromium triboride

  20. Aespoe hard rock laboratory. Field investigation methodology and instruments used in the preinvestigation phase, 1986-1990

    International Nuclear Information System (INIS)

    Almen, K.E.; Zellman, O.

    1991-12-01

    The Aespoe hard rock laboratory project started in 1986. The pre-investigation phase, 1986-1990, involved extensive field measurements from the surface as well as from boreholes, aimed at characterizing the rock formation with regard to geology, geohydrology, hydrochemistry and rock mechanics. The field investigation methodology used in the project was based on experience from and developments during the previous SKB study site investigation programme. However, in some respects the techniques were changed or modified. Major changes have been possible due to a new drilling technique, telescope-type drilling. This report describes the logistics of the investigation programme, characterized to a large extent by multi-purpose planning and performance of the activities in order to optimize the use of available resources; time, personnel and equipment. Preliminary hydraulic testing and groundwater sampling were conducted during the drilling of each borehole. When the drilling was completed an extensive set of singlehole investigations were carried out: geophysical logging, borehole radar, hydraulic tests of different kinds, water sampling and rock stress measurements. Multipackers were installed in the boreholes as soon as possible after the borehole investigations. The system enables monitoring of groundwater pressure, water sampling and groundwater flow measurements to be performed by means of dilution tests and tracer injection. Boreholes with such equipment were used as observation holes during interference pumping tests and long term hydraulic and tracer tests. The monitoring programme will continue during the subsequent phases of construction and operation of the Aespoe hard rock laboratory. (83 refs., 94 figs.) (au)

  1. Investigation of the phase formation and dielectric properties of Bi7Ta3O18

    International Nuclear Information System (INIS)

    Chon, M.P.; Tan, K.B.; Khaw, C.C.; Zainal, Z.; Taufiq Yap, Y.H.; Chen, S.K.; Tan, P.Y.

    2014-01-01

    Highlights: • Synthesis condition of Bi 7 TaO 3 O 18 had been determined. • Recombination of intermediate BiTaO 4 and Bi 3 TaO 7 phases are required for the Bi 7 TaO 3 O 18 phase formation. • Stable material as confirmed by thermal and structural analyses. • Typical ferroelectric showing high dielectric constants and low losses. • Resonance and thermal activated polarisation processes are responsible for the excellent dielectric characteristic. -- Abstract: Polycrystalline Bi 7 Ta 3 O 18 was synthesised at the firing temperature of 950 °C over 18 h via conventional solid state method. It crystallised in a monoclinic system with space group C2/m, Z = 4 similar to that reported diffraction pattern in the Inorganic Crystal Structure Database (ICSD), 1-89-6647. The refined lattice parameters were a = 34.060 (3) Å, b = 7.618 (9) Å, c = 6.647 (6) Å with α = γ = 90° and β = 109.210 (7), respectively. The intermediate phase was predominantly in high-symmetry cubic structure below 800 °C and finally evolved into a low-symmetry monoclinic structured, Bi 7 Ta 3 O 18 at 950 °C. The sample contained grains of various shapes with different orientations in the size ranging from 0.33–22.70 μm. The elemental analysis showed the sample had correct stoichiometry with negligible Bi 2 O 3 loss. Bi 7 Ta 3 O 18 was thermally stable and it exhibited a relatively high relative permittivity, 241 and low dielectric loss, 0.004 at room temperature, ∼30 °C and frequency of 1 MHz

  2. Environment-induced self-assembly in phase separated block copolymer systems: A SANS investigation

    International Nuclear Information System (INIS)

    Dutta, Naba K.; Thompson, Sandra; Roy Choudhury, Namita; Knott, Robert

    2006-01-01

    In this research, we examine the effect of non-selective solvent on the large-scale mesoscopic ordering in asymmetric block copolymers, poly(styrene-block-ethylene/butylene-block-styrene) (SEBS) using small angle neutron scattering technique (SANS). SANS measurements were carried out over a wide range of concentrations and temperatures. Evolution of the self-assembled phase morphology in such polymer with the thermodynamic selectivity of solvent, temperature and concentration has been discussed. Correlation between morphology and thermorheological behavior of the gels has also been established

  3. Investigation of metal-matrix composite containing liquid-phase dispersion

    Czech Academy of Sciences Publication Activity Database

    Strunz, Pavel; Mukherji, D.; Gilles, R.; Geue, T.; Rösler, J.

    2012-01-01

    Roč. 340, 012098 (2012), s. 1-15 ISSN 1742-6588. [5th European Conference on Neutron Scattering. Praha, 17.07.2011-21.07.2011] R&D Projects: GA MPO FR-TI1/378 Grant - others:European Commission(XE) RII3-CT-2003-505925 Program:FP6 Institutional support: RVO:61389005 Keywords : metal-matrix composite * liquid-phase dispersion * strengthening * neutron diffraction Subject RIV: BM - Solid Matter Physics ; Magnetism http://iopscience.iop.org/1742-6596/340/1/012098

  4. Performance characteristic of saturable three-phase interface transformers-investigations using a model simulation

    Energy Technology Data Exchange (ETDEWEB)

    Gierse, G; Pestka, J

    1981-11-01

    For electric locomotive drives equipped with converter fed squirrel cage induction motors the influence of different three-phase interface transformers on the smoothing of the motor currents is shown. In combination with a modified pulse-width-controlled thyristor firing system the size of the interface transformers can be greatly reduced without the distortion currents being greater than in the case of reactors in the motor supply lines. Finally, it is shown how the additional magnetic coupling of two driving systems can influence the behaviour of the two motors.

  5. Experimental investigation of two-stage thermoelectric generator system integrated with phase change materials

    DEFF Research Database (Denmark)

    Ahmadi Atouei, Saeed; Ranjbar, Ali Akbar; Rezaniakolaei, Alireza

    2017-01-01

    this amount of voltage just for 2100 s. Therefore, the proposed design makes TEG systems more suitable for wireless sensor applications when the heat source does not provide steady thermal energy. In this study, four different patterns of thermal power applied to the TTEG system are considered. These patterns...... experimentally. In the first stage, a TEG module installed between a phase change material (PCM) heat sink, as cooling system, and an electrical heater, as the heat source. Because of the inherent characteristics of PCMs to save the thermal energy as latent heat, the PCM heat sink is used as the heat source...

  6. 1-D Two-phase Flow Investigation for External Reactor Vessel Cooling

    International Nuclear Information System (INIS)

    Kim, Jae Cheol

    2007-02-01

    During a severe accident, when a molten corium is relocated in a reactor vessel lower head, the RCF(Reactor Cavity Flooding) system for ERVC (External Reactor Vessel Cooling) is actuated and coolants are supplied into a reactor cavity to remove a decay heat from the molten corium. This severe accident mitigation strategy for maintaining a integrity of reactor vessel was adopted in the nuclear power plants of APR1400, AP600, and AP1000. Under the ERVC condition, the upward two-phase flow is driven by the amount of the decay heat from the molten corium. To achieve the ERVC strategy, the two-phase natural circulation in the annular gap between the external reactor vessel and the insulation should be formed sufficiently by designing the coolant inlet/outlet area and gap size adequately on the insulation device. Also the natural circulation flow restriction has to be minimized. In this reason, it is needed to review the fundamental structure of insulation. In the existing power plants, the insulation design is aimed at minimizing heat losses under a normal operation. Under the ERVC condition, however, the ability to form the two-phase natural circulation is uncertain. Namely, some important factors, such as the coolant inlet/outlet areas, flow restriction, and steam vent etc. in the flow channel, should be considered for ERVC design. T-HEMES 1D study is launched to estimate the natural circulation flow under the ERVC condition of APR1400. The experimental facility is one-dimensional and scaled down as the half height and 1/238 channel area of the APR1400 reactor vessel. The air injection method was used to simulate the boiling at the external reactor vessel and generate the natural circulation two-phase flow. From the experimental results, the natural circulation flow rate highly depended on inlet/outlet areas and the circulation flow rate increased as the outlet height as well as the supplied water head increased. On the other hand, the simple analysis using the drift

  7. Experimental investigations of single and two-phase flow in a heated rod bundle

    International Nuclear Information System (INIS)

    Barthel, Frank; Franz, Ronald; Hampel, Uwe; Technische Univ. Dresden

    2013-01-01

    An experimental facility for the study of boiling flows in a 3 x 3 rod bundle geometry was setup. The bundle resembles in essential geometrical parts the geometry in a pressurized water reactor fuel element. The facility is operated with a refrigerant fluid. Beside standard instrumentation for temperature, pressure and flow rate we employed particle image velocimetry for single phase flow studies, gamma ray densitometry for integral gas fraction measurement sand ultrafast X-ray tomography for the study of the void dynamics in the cross-section. Moreover extensive thermo-instrumentation allows axial rod surface temperature measurements for the central heated rod. First results will be discussed in this article. (orig.)

  8. Experimental Investigation of Thermal Conductivity of Concrete Containing Micro-Encapsulated Phase Change Materials

    DEFF Research Database (Denmark)

    Pomianowski, Michal Zbigniew; Heiselberg, Per; Jensen, Rasmus Lund

    2011-01-01

    in this article utilizes integration of the concrete and the microencapsulated Phase Change Material (PCM). PCM has the ability to absorb and release significant amounts of heat at a specific temperature range. As a consequence of admixing PCM to the concrete, new thermal properties like thermal conductivity...... and specific heat capacity have to be defined. This paper presents results from the measurements of the thermal conductivity of various microencapsulated PCM-concrete and PCM-cement-paste mixes. It was discovered that increase of the amount of PCM decreases the thermal conductivity of the concrete PCM mixture....... Finally, a theoretical calculation methodology of thermal conductivity for PCM-concrete mixes is developed....

  9. The investigation of a two-layer fluid soliton pair using phase plane analysis

    International Nuclear Information System (INIS)

    Momeni, M.; Moslehi-Fard, M.; Alinejad, H.; Mahmoodi, J.

    2004-01-01

    Nonlinear long waves theory in a two-layer fluid system has been studied. The dynamical equations according to the normalized heights in first order are obtained using the reductive perturbation method and the equations of shallow water in each fluid and taking boundary conditions appropriate into account. Conserve energy form by definition a independent variable is found. By definition a Lyapunov function, the condition for stability are shown. A new technique was used to prove stability as well as existence of soliton pair using phase plane analysis. (author)

  10. Docetaxel, cisplatin and 5-fluorouracil induction chemotherapy followed by chemoradiotherapy or chemoradiotherapy alone in stage III-IV unresectable head and neck cancer. Results of a randomized phase II study

    Energy Technology Data Exchange (ETDEWEB)

    Takacsi-Nagy, Zoltan; Polgar, Csaba; Major, Tibor; Fodor, Janos [National Institute of Oncology, Center of Radiotherapy, Budapest (Hungary); Hitre, Erika [National Institute of Oncology, Department of Chemotherapy and Clinical Pharmacology, Budapest (Hungary); Remenar, Eva; Kasler, Miklos [National Institute of Oncology, Department of Head and Neck and Maxillofacial Surgery, Budapest (Hungary); Oberna, Ferenc [Bacs-Kiskun County Hospital, Department of Oral, Maxillofacial and Head and Neck Surgery, Kecskemet (Hungary); Goedeny, Maria [National Institute of Oncology, Department of Radiology, Budapest (Hungary)

    2015-08-15

    Concurrent chemoradiotherapy (CRT) is the standard treatment for advanced head and neck squamous cell carcinoma. In this phase II randomized study, the efficacy and toxicity of docetaxel, cisplatin and 5-fluorouracil induction chemotherapy (ICT) followed by concurrent CRT was compared with those after standard CRT alone in patients with locally advanced, unresectable head and neck cancer. Between January 2007 and June 2009, 66 patients with advanced (stage III or IV) unresectable squamous cell carcinoma of the head and neck (oral cavity, oropharynx, hypopharynx, and larynx) were randomly assigned to two groups: one receiving two cycles of docetaxel, cisplatin, and 5-fluorouracil ICT followed by CRT with three cycles of cisplatin and one treated by CRT alone. Response rate, local tumor control (LTC), locoregional tumor control (LRTC), overall survival (OS), progression-free survival (PFS), and toxicity results were assessed. Three patients from the ICT + CRT group did not appear at the first treatment, so a total of 63 patients were evaluated in the study (30 ICT + CRT group and 33 CRT group). Three patients died of febrile neutropenia after ICT. The median follow-up time for surviving patients was 63 months (range 53-82 months). The rate of radiologic complete response was 63 % following ICT + CRT, whereas 70 % after CRT alone. There were no significant differences in the 3-year rates of LTC (56 vs. 57 %), LRTC (42 vs. 50 %), OS (43 vs. 55 %), and PFS (41 vs. 50 %) in the ICT + CRT group and in the CRT group, respectively. The rate of grade 3-4 neutropenia was significantly higher in the ICT + CRT group than in the CRT group (37 and 12 %; p = 0.024). Late toxicity (grade 2 or 3 xerostomia) developed in 59 and 42 % in the ICT + CRT and CRT groups, respectively. The addition of ICT to CRT did not show any advantage in our phase II trial, while the incidence of adverse events increased. The three deaths as a consequence of ICT call attention to the importance of

  11. Applications of the phase function method ideas for the investigation of the two- and three-body system properties

    International Nuclear Information System (INIS)

    Petrov, N.M.; Pushkash, A.M.

    1985-01-01

    In accordance with the main idea of the phase function method the two-body off-shell scattering amplitudes are considered as the limit of the scattering amplitude sequence corresponding to the sequence of the R-radius cut-off potentials. The explicit analytical expression for the scattering amplitudes function is obtained in the case of separable potentials, due to which the three-body problem is investigated

  12. Data of fractures based on the deep borehole investigations in the Horonobe Underground Research Laboratory project. Phase 1

    International Nuclear Information System (INIS)

    Kusano, Tomohiro; Ishii, Eiichi

    2016-02-01

    Japan Atomic Energy Agency (JAEA) is performing the Horonobe Underground Research Laboratory Project, which includes a scientific study of the deep geological environment as a basis of research and development for geological disposal of high level radioactive wastes (HLW), in order to establish comprehensive techniques for the investigation, analysis and assessment of the deep geological environment in the sedimentary rock. This report aims at compiling fracture data of drill core obtained from the Horonobe Underground Research Laboratory Project (Phase 1). (author)

  13. Investigation of properties and performance of ceramic composite components: Final report on Phases 3 and 4

    Energy Technology Data Exchange (ETDEWEB)

    Curtin, W.A.; Halverson, H.; Carter, R.H.; Miraj, N.; Reifsnider, K.L. [Virginia Polytechnic Inst. and State Univ., Blacksburg, VA (United States)

    1998-01-15

    The objective of the Fossil Energy Advanced Research and Technology Development (AR and TD) Materials Program is to conduct research and development on materials for longer-term fossil energy applications as well as for generic needs of various fossil fuel technologies. The research program of the Materials Response Group at Virginia Tech addresses the need for reliable and durable structural ceramic composites to perform in high temperature environments. The research effort provides an experimental and analytical basis for the transition from properties of materials to performance of actual component structures. Phases 1 and 2 of the present program focused on the development of test capabilities, initial studies of component mechanical response under various conditions and the development of a life prediction methodology. These efforts have been described in previous reports. This report summarizes the major tasks completed under Phases 3 and 4 of the project. Overall, the authors have made significant progress in a broad spectrum of tasks in this program. Their efforts have encompassed component evaluation, assessment of new SiC-based composites with improved high-temperature potential, development of oxide coating materials for SiC, and the extension and development of new models for predicting the durability of composite components under specific operating conditions for various CMC applications. Each of these areas of work is an important area for achieving the ultimate goal of usable SiC-based composites in high-temperature corrosive environments typical of fossil energy applications.

  14. An investigation of two-phase flow instability using wavelet signal extraction technique

    International Nuclear Information System (INIS)

    Shang Zhi; Yang Ruichang; Cao Xuewu; Yang Yanhua

    2004-01-01

    When the oscillation periods of the instability of two-phase flow are sought with traditional methods of signal analysis, generally the Fourier transform must be employed and then the oscillation periods will be gotten at the location of the local maximum amplitude of frequency transform. However, Fourier transform will be difficult to clearly analyze the unsteady signals especially when the signals include many peaks and the noise interference is not generated by white noise in many areas of practical engineering like the oscillation of the instability of two-phase flow. The most effective solving method for the difficulty of Fourier transform is to analyze the signals directly in time domain. Wavelet analysis is able to search out the periods from time domain directly. It also has more excellent local characteristics than Fourier analysis in the both of time and frequency domains. In this paper, not only is a direct detecting method of the oscillation periods successfully applied based on the wavelet signal extraction techniques, but also the oscillation of density wave type of TYPE I is found as a kind of oscillations with a high-frequency harmonization

  15. Investigation of Thermal Interface Materials Using Phase-Sensitive Transient Thermoreflectance Technique: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Feng, X.; King, C.; DeVoto, D.; Mihalic, M.; Narumanchi, S.

    2014-08-01

    With increasing power density in electronics packages/modules, thermal resistances at multiple interfaces are a bottleneck to efficient heat removal from the package. In this work, the performance of thermal interface materials such as grease, thermoplastic adhesives and diffusion-bonded interfaces are characterized using the phase-sensitive transient thermoreflectance technique. A multi-layer heat conduction model was constructed and theoretical solutions were derived to obtain the relation between phase lag and the thermal/physical properties. This technique enables simultaneous extraction of the contact resistance and bulk thermal conductivity of the TIMs. With the measurements, the bulk thermal conductivity of Dow TC-5022 thermal grease (70 to 75 um bondline thickness) was 3 to 5 W/(m-K) and the contact resistance was 5 to 10 mm2-K/W. For the Btech thermoplastic material (45 to 80 μm bondline thickness), the bulk thermal conductivity was 20 to 50 W/(m-K) and the contact resistance was 2 to 5 mm2-K/W. Measurements were also conducted to quantify the thermal performance of diffusion-bonded interface for power electronics applications. Results with the diffusion-bonded sample showed that the interfacial thermal resistance is more than one order of magnitude lower than those of traditional TIMs, suggesting potential pathways to efficient thermal management.

  16. Automated recognition of helium speech. Phase I: Investigation of microprocessor based analysis/synthesis system

    Science.gov (United States)

    Jelinek, H. J.

    1986-01-01

    This is the Final Report of Electronic Design Associates on its Phase I SBIR project. The purpose of this project is to develop a method for correcting helium speech, as experienced in diver-surface communication. The goal of the Phase I study was to design, prototype, and evaluate a real time helium speech corrector system based upon digital signal processing techniques. The general approach was to develop hardware (an IBM PC board) to digitize helium speech and software (a LAMBDA computer based simulation) to translate the speech. As planned in the study proposal, this initial prototype may now be used to assess expected performance from a self contained real time system which uses an identical algorithm. The Final Report details the work carried out to produce the prototype system. Four major project tasks were: a signal processing scheme for converting helium speech to normal sounding speech was generated. The signal processing scheme was simulated on a general purpose (LAMDA) computer. Actual helium speech was supplied to the simulation and the converted speech was generated. An IBM-PC based 14 bit data Input/Output board was designed and built. A bibliography of references on speech processing was generated.

  17. Investigation of the liquid crystalline phase transitions using the new modified Pople Karasz model

    Science.gov (United States)

    Yazıcı, Mustafa; Özgan, Şükrü; Keskin, Mustafa

    2005-09-01

    Thermodynamics of solid nematic and nematic isotropic liquid transitions are studied by using a new modified model that combines the modified theories of Chandrasekhar et al. with those Keskin and Özgan which are based on the Pople Karasz theory. The thermodynamic properties of the disordered system are evaluated relative to those of the perfectly ordered one within the lowest approximation of the cluster variation method which is identical to the mean-field approximation. The results are compared with the some available experimental data, the predictions of the original Pople Karasz (PK) theory and its previous modified theories. For nematic isotropic and s(nematic) at the transition temperatures, the agreement is very good and much better than the predictions of the PK theory and its previous modified theories. For the solid nematic transition, all theories give very nearly the same results, but the values are significantly lower than the observed data. Moreover, one of the theoretical phase diagrams is also qualitatively similar to the experimental phase diagram for p-azoxyphenetole (PAA).

  18. Investigation of the liquid crystalline phase transitions using the new modified Pople-Karasz model

    International Nuclear Information System (INIS)

    Yazici, Mustafa; Oezgan, Suekrue; Keskin, Mustafa

    2005-01-01

    Thermodynamics of solid-nematic and nematic-isotropic liquid transitions are studied by using a new modified model that combines the modified theories of Chandrasekhar et al. with those Keskin and Oezgan which are based on the Pople-Karasz theory. The thermodynamic properties of the disordered system are evaluated relative to those of the perfectly ordered one within the lowest approximation of the cluster variation method which is identical to the mean-field approximation. The results are compared with the some available experimental data, the predictions of the original Pople-Karasz (PK) theory and its previous modified theories. For nematic-isotropic and s(nematic) at the transition temperatures, the agreement is very good and much better than the predictions of the PK theory and its previous modified theories. For the solid-nematic transition, all theories give very nearly the same results, but the values are significantly lower than the observed data. Moreover, one of the theoretical phase diagrams is also qualitatively similar to the experimental phase diagram for p-azoxyphenetole (PAA)

  19. Three-dimensional investigation of the two-phase flow structure in a bubbly pipe flow

    International Nuclear Information System (INIS)

    Hassan, Y.A.; Schmidl, W.D.; Ortiz-Villafuerte, J.

    1997-01-01

    Particle Image Velocimetry (PIV) is a non-intrusive measurement technique, which can be used to study the structure of various fluid flows. PIV is used to measure the time varying full field velocity data of a particle-seeded flow field within either a two-dimensional plane or three-dimensional volume. PIV is a very efficient measurement technique since it can obtain both qualitative and quantitative spatial information about the flow field being studied. This information can be further processed into information such as vorticity and pathlines. Other flow measurement techniques (Laser Doppler Velocimetry, Hot Wire Anemometry, etc...) only provide quantitative information at a single point. PIV can be used to study turbulence structures if a sufficient amount of data can be acquired and analyzed, and it can also be extended to study two-phase flows if both phases can be distinguished. In this study, the flow structure around a bubble rising in a pipe filled with water was studied in three-dimensions. The velocity of the rising bubble and the velocity field of the surrounding water was measured. Then the turbulence intensities and Reynolds stresses were calculated from the experimental data. (author)

  20. An investigation of phase transformation and crystallinity in laser surface modified H13 steel

    Science.gov (United States)

    Aqida, S. N.; Brabazon, D.; Naher, S.

    2013-03-01

    This paper presents a laser surface modification process of AISI H13 tool steel using 0.09, 0.2 and 0.4 mm size of laser spot with an aim to increase hardness properties. A Rofin DC-015 diffusion-cooled CO2 slab laser was used to process AISI H13 tool steel samples. Samples of 10 mm diameter were sectioned to 100 mm length in order to process a predefined circumferential area. The parameters selected for examination were laser peak power, overlap percentage and pulse repetition frequency (PRF). X-ray diffraction analysis (XRD) was conducted to measure crystallinity of the laser-modified surface. X-ray diffraction patterns of the samples were recorded using a Bruker D8 XRD system with Cu K α ( λ=1.5405 Å) radiation. The diffraction patterns were recorded in the 2 θ range of 20 to 80°. The hardness properties were tested at 981 mN force. The laser-modified surface exhibited reduced crystallinity compared to the un-processed samples. The presence of martensitic phase was detected in the samples processed using 0.4 mm spot size. Though there was reduced crystallinity, a high hardness was measured in the laser-modified surface. Hardness was increased more than 2.5 times compared to the as-received samples. These findings reveal the phase source of the hardening mechanism and grain composition in the laser-modified surface.

  1. Experimental investigation of extended Kalman Filter combined with carrier phase recovery for 16-QAM system

    Science.gov (United States)

    Shu, Tong; Li, Yan; Yu, Miao; Zhang, Yifan; Zhou, Honghang; Qiu, Jifang; Guo, Hongxiang; Hong, Xiaobin; Wu, Jian

    2018-02-01

    Performance of Extended Kalman Filter combined with the Viterbi-Viterbi phase estimation (VVPE-EKF) for joint phase noise mitigation and amplitude noise equalization is experimental demonstrated. Experimental results show that, for 11.2 Gbaud SP-16-QAM, the proposed VVPE-EKF achieves 0.9 dB required OSNR reduction at bit error ratio (BER) of 3.8e-3 compared to the VVPE. The result of maximum likelihood combined with VVPE (VVPE-ML) is only 0.3 dB. For 28 GBaud SP-16-QAM signal, VVPE-EKF achieves 3 dB required OSNR reduction at BER=3.8e-3 (7% HD-FEC threshold) compared to VVPE. And VVPE-ML can reduce the required OSNR for 1.7 dB compared to the VVPE. VVPE-EKF outperforms DD-EKF 3.7 dB and 0.7 dB for 11.2 GBaud and 28 GBaud system, respectively.

  2. Phase 2 environmental site investigation procedures and technologies for property transfer and PS and E development

    Science.gov (United States)

    1999-05-01

    The purpose of this project is to provide TxDOT with an improved procedure for conducting environmental site investigations at various stages during transportation infrastructure development. The project seeks to identify modern assessment technologi...

  3. Investigation of uranyl-ion hydrolysis in uranyl pertechnetate and uranyl perchlorates solutions by two-phases potentiometric titration method

    International Nuclear Information System (INIS)

    Volk, V.I.; Belikov, A.D.

    1977-01-01

    The applicability of the method of two-phase potentiometric titration for studying hydrolysis of multi-charge ions has been shown. Hydrolysis of uranyl-ion has been investigated and hydrolysis constants in the solutions of uranyl pertechnetate and perchlorate have been calculated equal to (6.2+-0.15)x10 -5 and (9.25+-0.5)10 -5 , respectively. Infrared spectra of the initial crystallohydrates of uranyl pertechnetate and perchlorate has been analyzed. The data on hydrolysis of an uranyl-ion and IR spectra of crystallohydrates of the investigated salts have revealed the ability of pertechnetate ion to complexing with an uranyl group

  4. Experimental investigation of stratified two-phase flows in the hot leg of a PWR for CFD validation

    Energy Technology Data Exchange (ETDEWEB)

    Vallee, Christophe; Lucas, Dirk [Helmholtz-Zentrum Dresden-Rossendorf (HZDR) e.V., Dresden (Germany). Inst. of Fluid Dynamics; Tomiyama, Akio [Kobe Univ. (Japan). Graduate School of Engineering; Murase, Michio [Institute of Nuclear Safety System Inc. (INSS), Fukui (Japan)

    2012-07-01

    Stratified two-phase flows were investigated in two different models of the hot leg of a pressurised water reactor (PWR) in order to provide experimental data for the development and validation of computational fluid dynamics (CFD) codes. Therefore, the local flow structure was visualised with a high-speed video camera. Moreover, one test section was designed with a rectangular cross-section to achieve optimum observation conditions. The phenomenon of counter-current flow limitation (CCFL) was investigated, which may affect the reflux condenser cooling mode in some accident scenarios. (orig.)

  5. Direct Investigations Of The Immobilization Of Radionuclides In The Alteration Phases Of Spent Nuclear Fuel

    International Nuclear Information System (INIS)

    Burns, Peter C.; Finch, Robert J.; Wronkiewicz, David J.

    2003-01-01

    radionuclides considered in the TSPA-VA (Total System Performance Analysis - Viability Assessment) Base Case Performance Analysis (CRWMS, 1998, cf. Table 3-14 in section 3.5.1) are of special concern because of their long half-lives, radiological toxicities, and potential mobilities under repository conditions. These are five actinide isotopes, Np-237, Pu-239, Pu-242, U-234, and Pa- 231, and four fission products, Tc-99, I-129, Se-79, and C-14. In addition, Am-241 is important because it is a parent of Np-237. An understanding of the behaviors of these elements under repository-relevant conditions is essential to safe disposal. Natural analogue studies of the mineral uraninite, UO2+x (an analogue for UO2 in spent fuel), as well as several laboratory-scale simulations, confirm that spent fuel is unstable under the moist, oxidizing conditions expected in the proposed repository at Yucca Mountain. Once containers are breached, alteration of the spent fuel m ay be rapid, with the most abundant alteration products being uranyl (U6+) phases. Shortly after groundwater or condensed water vapor contacts spent fuel in the proposed repository, uranyl phases are likely to be abundant in the vicinity of the spent fuel. Most of the uranyl phases that will form in the repository are already known as minerals from natural systems. Many of these uranyl phases can persist for thousands of years, as demonstrated by studies of natural analogues (Finch et al. 1996). It is likely that uranyl phases forming due to the alteration of spent fuel will incorporate many of the radionuclides contained in the spent fuel (Burns et al. 1997), thus having a profound impact upon the mobility of the radionuclides. Our ongoing research is leading to an understanding of the impact of incorporation of radionuclides into uranyl phases. Such information is essential to an understanding of the long-term performance of the geological repository. Knowledge of the crystal structures, chemistries, stabilities and

  6. Theoretical Investigation of the Structural Stabilities of Ceria Surfaces and Supported Metal Nanocluster in Vapor and Aqueous Phases

    Energy Technology Data Exchange (ETDEWEB)

    Ren, Zhibo [State Key Laboratory of Chemical Resource Engineering, Beijing University of Chemical Technology, Beijing 100029, China; Institute for Integrated Catalysis, Pacific Northwest National Laboratory, Richland, Washington 99352, United States; Liu, Ning [State Key Laboratory of Chemical Resource Engineering, Beijing University of Chemical Technology, Beijing 100029, China; Institute for Integrated Catalysis, Pacific Northwest National Laboratory, Richland, Washington 99352, United States; Chen, Biaohua [State Key Laboratory of Chemical Resource Engineering, Beijing University of Chemical Technology, Beijing 100029, China; Li, Jianwei [State Key Laboratory of Chemical Resource Engineering, Beijing University of Chemical Technology, Beijing 100029, China; Mei, Donghai [Institute for Integrated Catalysis, Pacific Northwest National Laboratory, Richland, Washington 99352, United States

    2018-01-25

    Understanding the structural stability and dynamics at the interface between the solid metal oxide and aqueous phase is significant in a variety of industrial applications including heterogeneous catalysis and environmental remediation. In the present work, the stabilities of three low-index ceria (CeO2) surfaces, i.e., (111), (110) and (100) in vapor and aqueous phases were studied using ab initio molecular dynamics simulations and density functional theory (DFT) calculations. Gibbs surface free energies as a function of temperature, water partial pressure, and water coverages were calculated using DFT based atomistic thermodynamic approach. On the basis of surface free energies, the morphology and exposed surface structures of the CeO2 nanoparticle were predicted using Wulff construction principle. It is found that the partially hydroxylated (111) and (100) are two major surface structures of CeO2 nanoparticles in vapor phase at ambient temperature (300 K). As the temperature increases, the fully dehydrated (111) surface gradually becomes the most dominant surface structure. While in aqueous phase, the exposed surface of the CeO2 nanoparticle is dominated by the hydroxylated (110) structure at 393 K. Finally, the morphology and stability of a cuboctahedron Pt13 nanocluster supported on CeO2 surfaces in both gas and aqueous phases were investigated. In gas phase, the supported Pt13 nanocluster has the tendency to wetting the CeO2 surface due to the strong metal-support interaction. The calculated interaction energies suggest the CeO2(110) surface provides the best stability for the Pt13 nanocluster. The CeO2 supported Pt13 nanoclusters are oxidized. Compared to the gas phase, the morphology of the CeO2 supported Pt13 nanocluster is less distorted due to the solvation effect provided by surrounding water molecules in aqueous phase. More electrons are transferred from the Pt13 nanocluster to the CeO2 support, implying the supported Pt13 nanocluster is further

  7. Experimental investigation of the U–Zr–Al ternary phase diagram: Isothermal sections at 673 K and 1073 K

    Energy Technology Data Exchange (ETDEWEB)

    Moussa, C.; Désévédavy, F.; Noël, H.; Pasturel, M.; Gouttefangeas, F. [ISCR/CSM, Université de Rennes1, UMR-CNRS 6226, Campus de Beaulieu, 263 Avenue du Général Leclerc, 35042 Rennes Cedex, France, (France); Dubois, S. [CEA/DEN/DEC, Cadarache, 13108 St. Paul Lez Durance (France); Stepnik, B. [AREVA/CERCA, 10 Rue Juliette Récamier, 69006 Lyon (France); Tougait, O., E-mail: tougait@univ-rennes1.fr [ISCR/CSM, Université de Rennes1, UMR-CNRS 6226, Campus de Beaulieu, 263 Avenue du Général Leclerc, 35042 Rennes Cedex, France, (France); UCCS, UMR 8181 CNRS, Université Lille 1, ENSCL, Avenue Mendeleiev, 59655 Villeneuve d’Ascq Cedex (France)

    2015-06-15

    Highlights: • Isothermal sections of the U–Zr–Al system were investigated for 673 K and 1073 K. • The crystallographic properties of the equilibrium phases were checked. • The ternary extension of both unary and binary phases was determined. • The solubility of Al into UZr{sub 2} (δ-phase) was assessed by diffusion couples. • The microstructure of quenched alloys is discussed. - Abstract: Isothermal sections at 673 K and 1073 K of the ternary U–Zr–Al system were established in the whole concentration range, by means of powder X-ray diffraction, scanning electron microscopy–energy dispersive X-ray spectroscopy and differential thermal analysis. All measured compositions and unit-cell refinements were performed at room temperature from quenched samples annealed at 1073 K and 673 K for four and eight weeks respectively. For both temperatures, the Al-rich corner of the phase diagram is characterized by extended homogeneity ranges due to mutual exchange between U and Zr in UAl{sub 3} (cubic, AuCu{sub 3}-type) and in the Laves phase UAl{sub 2} (cubic, MgCu{sub 2}-type). Minute U solubility in ZrAl{sub 2} (hexagonal, MgZn{sub 2}-type) and in Zr{sub 2}Al (hexagonal, Ni{sub 2}In-type) was evaluated to be of the order of 1 at.% U. For the other binary compounds, the solubility of the third component was found negligible. At 1073 K, the solid solution based on γU (cubic, W-type) which covers the U–Zr binary axis up to 95.5 at.% Zr, allows also some limited solubility of Al [maximum of 5 at.%]. For Al-content below 66 at.%, most of the phase relations comprise equilibria between the Zr–Al binaries and the γ(U,Zr,Al) solid solution. At 673 K, the U–Zr axis is found in agreement with the literature data and no Al solubility could be detected in αU, αZr and UZr{sub 2} (δ phase). The phase relations are mainly established between Zr–Al binaries and αU. For monolithic UMo fuel with a Zr diffusion barrier foil cladded with Al, the main interaction

  8. Investigation of biomedical inner microstructures with hard X-ray phase-contrast imaging

    Energy Technology Data Exchange (ETDEWEB)

    Shu Hang [Beijing Synchrotron Radiation Facility, Institute of High Energy Physics, CAS, 100049 Beijing (China); Graduate University of the Chinese Academy of Sciences, 100864 Beijing (China); Zhu Peiping [Beijing Synchrotron Radiation Facility, Institute of High Energy Physics, CAS, 100049 Beijing (China); Chen Bo [Department of Physics, University of Science and Technology of China, Hefei 230026 (China); Liu Bo; Yin Hongxia [Capital University of Medical Sciences, 100054 Beijing (China); Li Enrong [Beijing Synchrotron Radiation Facility, Institute of High Energy Physics, CAS, 100049 Beijing (China); Graduate University of the Chinese Academy of Sciences, 100864 Beijing (China); Liu Yijin [Department of Physics, University of Science and Technology of China, Hefei 230026 (China); Wang Junyue [Beijing Synchrotron Radiation Facility, Institute of High Energy Physics, CAS, 100049 Beijing (China); Graduate University of the Chinese Academy of Sciences, 100864 Beijing (China); Yuan Qingxi; Huang Wanxia; Fang Shouxian [Beijing Synchrotron Radiation Facility, Institute of High Energy Physics, CAS, 100049 Beijing (China); Wu Ziyu [Beijing Synchrotron Radiation Facility, Institute of High Energy Physics, CAS, 100049 Beijing (China); National Center for NanoScience and Technology, 100080 Beijing (China)], E-mail: wuzy@ihep.ac.cn

    2007-09-21

    Hard X-ray Phase-Contrast Imaging (HX-PCI) is a new and valuable method that may provide information of the inner parts of an opaque object. Previous reports demonstrated its applicability in soft and hard tissue imaging. Here we provide further evidence for improved image quality and the effective capability to distinguish inner microstructures in real biomedical systems such as cochlea. Experiments performed both at the 4W1A beamline of the Beijing Synchrotron Radiation Facility (BSRF) and at the Taiwan National Synchrotron Radiation Research Center (NSRRC) clearly show details of samples' inner microstructure with a resolution of a few microns. The improved spatial resolution is a relevant achievement for future improved understanding and clinical trials.

  9. Investigating Solutions to Wind Washing Issues in Two-Story Florida Homes, Phase 2

    Energy Technology Data Exchange (ETDEWEB)

    Withers, C. [Building America Partnership for Improved Residential Construction, Cocoa, FL (United States); Kono, J. [Building America Partnership for Improved Residential Construction, Cocoa, FL (United States)

    2015-04-01

    This report provides results from a second-phase research study of a phenomenon generally referred to as wind washing. Wind washing is the movement of unconditioned air around or through building thermal barriers in such a way as to diminish or nullify the intended thermal performance. In some cases, thermal and air barriers are installed very poorly or not at all, and air can readily move from unconditioned attic spaces into quasi-conditioned interstitial spaces. This study focused on the impact of poorly sealed and insulated floor cavities adjacent to attic spaces in Florida homes. In these cases, unconditioned attic air can be transferred into floor cavities through pathways driven by natural factors such as wind, or by thermal differences between the floor cavity and the attic. Air can also be driven into a floor cavity through mechanical forces imposed by return duct leakage in the floor cavity.

  10. Experimental investigation of void coalescence in a dual phase steel using X-ray tomography

    International Nuclear Information System (INIS)

    Landron, C.; Bouaziz, O.; Maire, E.; Adrien, J.

    2013-01-01

    In situ tensile tests were carried out during X-ray microtomography imaging of a smooth and a notched specimen of dual phase steel. The void coalescence was first qualitatively observed and quantitative data concerning this damage step was then acquired. The void coalescence criteria of Brown and Embury and of Thomason were then tested against the experimental data at both the macroscopic and local levels. Although macroscopic implementation of the criteria gave acceptable results, the local approach was probably closest to the real nature of void coalescence, because it takes into account local coalescence events observed experimentally before final fracture. The correlation between actual coalescing couples of cavities and local implementation of the two criteria showed that the Thomason criterion is probably the best adapted to predict the local coalescence events in the case of the material studied

  11. Improving Performance of Cold-Chain Insulated Container with Phase Change Material: An Experimental Investigation

    Directory of Open Access Journals (Sweden)

    Li Huang

    2017-12-01

    Full Text Available The cold-chain transportation is an important means to ensure the drug and food safety. An cold-chain insulated container incorporating with Phase Change Material (PCM has been developed for a temperature-controlled transportation in the range of 2~8 °C. The container configuration and different preconditioning methods have been determined to realize a 72-h transportation under extremely high, extremely low, and alternating temperature conditions. The experimental results showed that the temperature-controlled time was extended from 1 h to more than 80 h and the internal temperature maintained at 4~5 °C by using a PCM with a melting/freezing point of 5 °C, while the container presented a subcooling effect in a range of −1~2 °C when using water as PCM. The experimental values of the temperature-controlled time agreed well with the theoretical values.

  12. Competitive grain growth in directional solidification investigated by phase field simulation

    International Nuclear Information System (INIS)

    Li Junjie; Wang Zhijun; Wang Jincheng; Yang Yujuan

    2012-01-01

    During directional solidification, the competitive dendritic growth between various oriented grains is a key factor to obtain desirable texture. In order to understand the mechanism of competitive dendritic growth, the phase field method was adopted to simulate the microstructure evolution of bicrystal samples. The simulation has well reproduced the whole competitive growth process for both diverging and converging dendrites. In converging case, besides the block of the unfavorably oriented dendrite by the favorably oriented one, the unfavorably oriented dendrite is also able to overgrow the favorable one under the condition of relatively low pulling velocity. This unusual overgrowth is dictated by the solute interaction of the converging dendrite tips. In diverging case, it was found that the grain boundary can be either inclined or parallel to the favorably oriented grain depending on the disposition of two grains.

  13. Symmetry analysis in the investigation of the order-disorder phase transition and possible structural deformations

    Energy Technology Data Exchange (ETDEWEB)

    Gurin, O V; Syromyatnikov, V N [AN SSSR, Sverdlovsk. Inst. Fiziki Metallov; Sikora, W [Joint Inst. for Nuclear Research, Dubna (USSR)

    1984-08-01

    Order-disorder phase transitions for the Me-X structures in Nb-H(D) hydrides with hydrogen (deuterium) ordering over the 12d tetrahedral interstices of the GAMMAsub(c)sup(v) lattice and for the Me-X and Me-X/sub 2/ oxides in the Ta-O system with oxygen ordering over octahedral 6b interstices are presented. The concentration of interstitial atoms is assumed to be constant. All possible models of ordered structures with a GAMMAsub(o)sup(b) lattice were determined using symmetry analysis. The possible structural deformations consistent with each variant of the ordering of the interstitial atoms were also considered. The structural deformations include the displacements of the metal atoms and of the centres of the interstices which were deduced using symmetry analysis. The results of the analysis of the final structure symmetry raise the question of understanding the nature of superstructure reflections in neutron diffraction patterns.

  14. Experimental investigation of a two-phase closed thermosyphon assembly for passive containment cooling system

    Energy Technology Data Exchange (ETDEWEB)

    Nam, Kyung Ho [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Kim, Sang Nyung [Kyunghee Univ., Gyeonggi-do (Korea, Republic of)

    2017-06-15

    After the Fukushima accident, increasing interest has been raised in passive safety systems that maintain the integrity of the containment building. To improve the reliability and safety of nuclear power plants, long-term passive cooling concepts have been developed for advanced reactors. In a previous study, the proposed design was based on an ordinary cylindrical Two-Phase Closed Thermosyphon (TPCT). The exact assembly size and number of TPCTs should be elaborated upon through accurate calculations based on experiments. While the ultimate goal is to propose an effective MPHP design for the PCCS and experimentally verify its performance, a TPCT assembly that was manufactured based on the conceptual design in this paper was tested.

  15. Investigations on liquid phase electroepitaxial growth kinetics of GaAs

    International Nuclear Information System (INIS)

    Mouleeswaran, D.; Dhanasekaran, R.

    2004-01-01

    This paper presents a model based on solving a two-dimensional diffusion equation incorporating the electromigration effect by numerical simulation method corresponding to liquid phase electroepitaxial (LPEE) growth of GaAs, whose growth is limited by diffusion and electro migration of solute species. Using the numerical simulation method, the concentration profiles of As in Ga rich solution during the electroepitaxial growth of GaAs have been constructed in front of the growing crystal interface. Using the concentration gradient at the interface, the growth rate and thickness of the epitaxial layer of GaAs have been determined for different experimental growth conditions. The proposed model is based on the assumption that there is no convection in the solution. The results are discussed in detail

  16. Experimental investigations of turbulent temperature fluctuations and phase angles in ASDEX Upgrade

    Science.gov (United States)

    Freethy, Simon

    2017-10-01

    A complete experimental understanding of the turbulent fluctuations in tokamak plasmas is essential for providing confidence in the extrapolation of heat transport models to future experimental devices and reactors. Guided by ``predict first'' nonlinear gyrokinetic simulations with the GENE code, two new turbulence diagnostics were designed and have been installed on ASDEX Upgrade (AUG) to probe the fundamentals of ion-scale turbulent electron heat transport. The first, a 30-channel correlation ECE (CECE) radiometer, measures radial profiles (0.5 a levels are in the range 0.3 - 0.8%. The second is formed by the addition of a reflectometer on the same line of sight to enable measurements of the phase angle between turbulent density and temperature fluctuations. Design predictions are followed by a more traditional ``post-diction'' validation study with GENE. Using a cutting edge synthetic diagnostic GENE shows a factor 1.6 - 2 over-prediction of the fluctuation amplitude, while matching both ion and electron heat fluxes within experimental error. Detailed sensitivity scans are underway to understand the robustness of this disagreement and a detailed assessment of the experimental errors has been carried out. The discrepancy opens questions about the role of multi-scale turbulence physics, but also indicates the need for the comparison of more experimental turbulence properties to have a more complete validation hierarchy. In an effort to understand the discrepancy, predictions of the nT-phase and the radial correlation length have been made along with an assessment of their sensitivity to experimental errors. Comparison to experimental measurements will be discussed. This work is supported in part by the US DOE under Grants DE-SC0006419 and DE-SC0017381. This work has also received funding from the European Union's Horizon 2020 research and innovation programme under Grant agreement number 633053.

  17. An investigation into the effects of the froth phase on the recovery of coal by flotation

    Energy Technology Data Exchange (ETDEWEB)

    Crawshaw, S A.M. [University of Nottingham, Nottingham (UK). Department of Mining Engineering

    1989-11-01

    The project aimed to investigate the effects of frother type and concentration on the recovery of coal by flotation, to study froth structure by photographic and image analysis techniques, and to use the information obtained in various modelling techniques to simulate the process of coal flotation. 221 refs., 136 figs., 6 apps.

  18. Differentiation of irradiation and cetuximab induced skin reactions in patients with locally advanced head and neck cancer undergoing radioimmunotherapy: the HICARE protocol (Head and neck cancer: ImmunoChemo and Radiotherapy with Erbitux) – a multicenter phase IV trial

    International Nuclear Information System (INIS)

    Habl, G; Potthoff, K; Haefner, MF; Abdollahi, A; Hassel, JC; Boller, E; Indorf, M; Debus, J

    2013-01-01

    In order to improve the clinical outcome of patients with locally advanced squamous cell carcinoma of the head and neck (LASCCHN) not being capable to receive platinum-based chemoradiation, radiotherapy can be intensified by addition of cetuximab, a monoclonal antibody that blocks the epidermal growth factor receptor (EGFR). The radioimmunotherapy with cetuximab is a feasible treatment option showing a favourable toxicity profile. The most frequent side effect of radiotherapy is radiation dermatitis, the most common side effect of treatment with cetuximab is acneiform rash. Incidence and severity of these frequent, often overlapping and sometimes limiting skin reactions, however, are not well explored. A clinical and molecular differentiation between radiogenic skin reactions and skin reactions caused by cetuximab which may correlate with outcome, have never been described before. The HICARE study is a national, multicenter, prospective phase IV study exploring the different types of skin reactions that occur in patients with LASCCHN undergoing radioimmun(chemo)therapy with the EGFR inhibitor cetuximab. 500 patients with LASCCHN will be enrolled in 40 participating sites in Germany. Primary endpoint is the rate of radiation dermatitis NCI CTCAE grade 3 and 4 (v. 4.02). Radioimmunotherapy will be applied according to SmPC, i.e. cetuximab will be administered as loading dose and then weekly during the radiotherapy. Irradiation will be applied as intensity-modulated radiation therapy (IMRT) or 3D-dimensional radiation therapy. The HICARE trial is expected to be one of the largest trials ever conducted in head and neck cancer patients. The goal of the HICARE trial is to differentiate skin reactions caused by radiation from those caused by the monoclonal antibody cetuximab, to evaluate the incidence and severity of these skin reactions and to correlate them with outcome parameters. Besides, the translational research program will help to identify and confirm novel

  19. Phase II study of tolerance and efficacy of hyperfractionated radiotherapy and 5-fluorouracil, cisplatin, and paclitaxel (Taxol) in stage III and IV inoperable and/or unresectable head-and-neck squamous cell carcinoma: A-2 protocol

    International Nuclear Information System (INIS)

    Abitbol, Andre; Abdel-Wahab, May; Lewin, Alan; Troner, Michael; Rodrigues, Maria-Amelia; Hamilton-Nelson, Kara L.; Markoe, Arnold

    2002-01-01

    Purpose: To determine the toxicity and efficacy of concurrent 5-fluorouracil (5-FU), cisplatin, and paclitaxel (Taxol) and hyperfractionated radiotherapy in locally advanced squamous cell carcinoma of the head and neck. Methods and Materials: Twenty-seven patients were entered into this Phase II trial. Eligible patients had Stage III or IV head-and-neck squamous cell carcinoma arising from the oral cavity, hypopharynx, oropharynx, nasopharynx, or larynx. The plan of treatment consisted of hyperfractionated radiotherapy (74.4 Gy at twice daily fractions of 1.2 Gy). Chemotherapy was given on Weeks 1, 5, and 8 as follows: 5-FU at 750 mg/m 2 as a constant infusion for 24 h for 3 days; cisplatin at 50 mg/m 2 in 250-500 mL D5 0.5 NS or NS infusion during 2-4 h, and paclitaxel at 70 mg/m 2 infused in 500 mL NS during 3 h. Results: The overall survival rate of the entire group was 81.5%, 66.7%, and 63% at 1, 2, and 3 years, respectively. The median follow-up was 40.2 months (range 30-62). Of the 27 patients, 19 (70%) had a complete response and an overall survival rate of 100% at 1 year and 94% at 2 and 3 years. The disease-free survival rate of the latter group was 95% at 1 year and 84% at 2 and 3 years. Of the 27 patients, 18 (67%) maintained the complete response until the last follow-up visit or death. Percutaneous endoscopic gastrostomy dependency occurred for a median of 7.1 months. Grade 3 and 4 mucositis occurred in 20 and 3 patients, respectively. Six patients were hospitalized for leukopenic fever. Late toxicities included L'Hermitte syndrome (n=3), osteoradionecrosis (n=1), hypothyroidism (n=4), paresthesias (n=1), aspiration pneumonia (n=3), and esophageal strictures (8 patients underwent dilation). Conclusion: Combining hyperfractionated radiotherapy concurrently with 5-FU, cisplatin, and paclitaxel results in acceptable efficacy and toxicity. However, although a locoregional control benefit is suggested by the preliminary results of this trial, it needs to be

  20. Phase Content and Equilibrium Relationships in Ternary Systems MOx/VO2,5/PO2,5 (M = TiIV, ZrIV, NbV; x = 2 or 2,5) with Additions for Four-Component System Ti/Cr/P/O

    International Nuclear Information System (INIS)

    Titlbach, Sven

    2014-01-01

    In the systems TiO 2 / V 2 O 5 / P 2 O 5 , ZrO 2 / V 2 O 5 / P 2 O 5 and Nb 2 O 5 / V 2 O 5 / P 2 O 5 studies on phase composition and the equilibrium relations were performed in the context of the heterogeneously catalyzed gas-phase oxidation of n-butane to maleic anhydride. Here is a selection of the research findings: in the system TiO 2 / V 2 O 5 / P 2 O 5 the hitherto unknown orthophosphate (VO)Ti 6 (PO 4 ) 9 and the mixed crystal series Ti(P 1-x V x ) 2 O 7 (0 ≤ x ≤ 0,24; 0,30 ≤ x ≤ 0,43) with miscibility gap was detected. In the quasi-ternary system ZrO 2 / V 2 O 5 / P 2 O 5 the literature well described gapless solid solution Zr(P 1-x V x ) 2 O 7 was confirmed and investigated radiographically and by NMR spectroscopy. In the system Nb 2 O 5 / V 2 O 5 / P 2 O 5 the mixed crystal series Nb 1-x V x O(PO 4 ) (0 ≤ x ≤ 0,36), P 1-x V x Nb 9 O 25 (0 ≤ x ≤ 1) and NbOP 1-x V x O 4 (0 ≤ x ≤ 0,20) were found.

  1. Experimental investigation of effect of spacer on two phase turbulent mixing rate in subchannels of pressure tube type BWR

    Energy Technology Data Exchange (ETDEWEB)

    Verma, Shashi Kant; Sinha, S.L. [National Institute of Technology, Raipur (India). Mechanical Engineering Dept.; Chandraker, D.K. [Bhabha Atomic Research Centre, Mumbai (India). Reactor Design and Development Group

    2017-11-15

    Turbulent mixing rate between adjacent subchannels in a two-phase flow has been known to be strongly dependent on the flow pattern. The most important aspect of turbulent motion is that the velocity and pressure at a fixed point do not remain constant with time even in steady state but go through very irregular high frequency fluctuations. These fluctuations influence the diffusion of scalar and vector quantities. The Advanced Heavy Water Reactor (AHWR) is a vertical pressure tube type, heavy water moderated and boiling light water cooled natural circulation based reactor. The fuel bundle of AHWR contains 54 fuel rods set in three concentric rings of 12, 18 and 24 fuel rods. This fuel bundle is divided into number of imaginary interacting flow channel called subchannels. Alteration from single phase to two phase flow situation occurs in reactor rod bundle with raise in power. The two phase flow regimes like bubbly, slug-churn, and annular flow are generally encountered in reactor rod bundle. Prediction of thermal margin of the reactor has necessitated the investigation of turbulent mixing rate of coolant between these subchannels under these flow regimes. Thus, it is fundamental to estimate the effect of spacer grids on turbulent mixing between subchannels of AHWR rod bundle.

  2. Impact of phase stability on the corrosion behavior of the austenitic candidate materials for NNWSI [Nevada Nuclear Waste Storage Investigations

    International Nuclear Information System (INIS)

    Bullen, D.B.; Gdowski, G.E.; McCright, R.D.

    1987-10-01

    The Nuclear Waste Management Program at Lawrence Livermore National Laboratory is responsible for the development of the waste package design to meet the Nuclear Regulatory Commission licensing requirements for the Nevada Nuclear Waste Storage Investigations (NNWSI) Project. The metallic container component of the waste package is required to assist in providing substantially complete containment of the waste for a period of up to 1000 years. Long term phase stability of the austenitic candidate materials (304L and 316L stainless steels and alloy 825) over this time period at moderate temperatures (100-250 0 C) can impact the mechanical and corrosion behavior of the metal barrier. A review of the technical literature with respect to phase stability of 304L, 316L and 825 is presented. The impact of martensitic transformations, carbide precipitation and intermediate (σ, chi, and eta) phase formation on the mechanical properties and corrosion behavior of these alloys at repository relevant conditions is discussed. The effect of sensitization on intergranular stress corrosion cracking (IGSCC) of each alloy is also addressed. A summary of the impact of phase stability on the degradation of each alloy in the proposed repository environment is included. 32 refs., 6 figs

  3. Investigation of a two-phase nozzle flow and validation of several computer codes by the experimental data

    International Nuclear Information System (INIS)

    Kedziur, F.

    1980-03-01

    Stationary experiments with a convergent nozzle are performed in order to validate advanced two-phase computer codes, which find application in the blowdown-phase of a loss-of-coolant accident (LOCA). The steam/water flow presents a broad variety of initial conditions: The pressure varies between 2 and 13 MPa, the void fraction between 0 (subcooled) and about 80%, a great number of subcritical as well as critical experiments with different flow pattern is investigated. Additional air/water experiments serve for the separation of phase transition effects. The transient acceleration of the fluid in the LOCA-case is simulated by a local acceleration in the experiments. The layout of the nozzle and the applied measurement technique allow for a separate testing of physical models and the determination of empirical model parameters, respectively: In the four codes DUESE, DRIX-20, RELAP4/MOD6 and STRUYA the models - if they exist - for slip between the phases, thermodynamic non-equilibrium, pipe friction and critical mass flow rate are validated and criticised in comparison with the experimental data, and the corresponding model parameters are determined. The parameters essentially are a function of the void fraction. (orig.) [de

  4. Investigation of the effects of phase transformations in micro and nano aluminum powders on kinetics of oxidation using thermogravimetric analysis.

    Science.gov (United States)

    Saceleanu, Florin; Atashin, Sanam; Wen, John Z

    2017-07-26

    Aluminum micro and nanoparticles are key ingredients in the synthesis of nano energetic materials. Hence it is important to characterize the kinetics and the rate controlling process of their oxidation. The literature shows that the mass diffusion and phase transformation within the aluminum oxide shell are important. However, the description of physical processes regarding simultaneous oxidation and phase transformation is lacking. In this paper, the controlled thermogravimetric (TGA) oxidation of 40-60 nm and 1 µm Al powders is investigated at constant heating rates and under isothermal conditions, respectively, upon varying the partial pressure of oxygen. It is found that the core-shell model of homogenous oxidation is applicable to explain the TGA results when the shell does not undergo phase transformation, which predicts the apparent activation energy in good agreement with the literature data. On the other hand, the simultaneous oxidation and phase transformation is able to be addressed using the JMAK model which reveals key parameters of the rate controlling processes. Mass diffusion is indeed rate determining during the oxidation of Al micro and nanopowders while the kinetics of the reaction is fast. Unlike the micron powders, the particle size distribution has a significant effect on the shape of the oxidation curves of the nanopowders.

  5. Review of Available Data for Validation of Nuresim Two-Phase CFD Software Applied to CHF Investigations

    Directory of Open Access Journals (Sweden)

    D. Bestion

    2009-01-01

    Full Text Available The NURESIM Project of the 6th European Framework Program initiated the development of a new-generation common European Standard Software Platform for nuclear reactor simulation. The thermal-hydraulic subproject aims at improving the understanding and the predictive capabilities of the simulation tools for key two-phase flow thermal-hydraulic processes such as the critical heat flux (CHF. As part of a multi-scale analysis of reactor thermal-hydraulics, a two-phase CFD tool is developed to allow zooming on local processes. Current industrial methods for CHF mainly use the sub-channel analysis and empirical CHF correlations based on large scale experiments having the real geometry of a reactor assembly. Two-phase CFD is used here for understanding some boiling flow processes, for helping new fuel assembly design, and for developing better CHF predictions in both PWR and BWR. This paper presents a review of experimental data which can be used for validation of the two-phase CFD application to CHF investigations. The phenomenology of DNB and Dry-Out are detailed identifying all basic flow processes which require a specific modeling in CFD tool. The resulting modeling program of work is given and the current state-of-the-art of the modeling within the NURESIM project is presented.

  6. In situ investigation of ordering phase transformations in FePt magnetic nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Wittig, James E., E-mail: j.wittig@vanderbilt.edu [Interdisciplinary Materials Science, Vanderbilt University, PMB 351683, 2301 Vanderbilt Place, Nashville, TN 37232 (United States); Bentley, James, E-mail: bentleyj48@gmail.com [Materials Science and Technology Division, Oak Ridge National Laboratory, PO Box 2008, Oak Ridge, TN 37831-6376 (United States); Allard, Lawrence F., E-mail: allardlfjr@ornl.gov [Materials Science and Technology Division, Oak Ridge National Laboratory, PO Box 2008, Oak Ridge, TN 37831-6376 (United States)

    2017-05-15

    In situ high-resolution electron microscopy was used to reveal information at the atomic level for the disordered-to-ordered phase transformation of equiatomic FePt nanoparticles that can exhibit outstanding magnetic properties after transforming from disordered face-centered-cubic into the tetragonal L1{sub 0} ordered structure. High-angle annular dark-field imaging in the scanning transmission electron microscope provided sufficient contrast between the Fe and Pt atoms to readily monitor the ordering of the atoms during in situ heating experiments. However, during continuous high-magnification imaging the electron beam influenced the kinetics of the transformation so annealing had to be performed with the electron beam blanked. At 500 °C where the reaction rate was relatively slow, observation of the transformation mechanisms using this sequential imaging protocol revealed that ordering proceeded from (002) surface facets but was incomplete and multiple-domain particles were formed that contained anti-phase domain boundaries and anti-site defects. At 600 and 700 °C, the limitations of sequential imaging were revealed as a consequence of increased transformation kinetics. Annealing for only 5 min at 700 °C produced complete single-domain L1{sub 0} order; such single-domain particles were more spherical in shape with (002) facets. The in situ experiments also provided information concerning nanoparticle sintering, coalescence, and consolidation. Although there was resistance to complete sintering due to the crystallography of L1{sub 0} order, the driving force from the large surface-area-to-volume ratio resulted in considerable nanoparticle coalescence, which would render such FePt nanoparticles unsuitable for use as magnetic recording media. Comparison of the in situ data acquired using the protocol described above with parallel ex situ annealing experiments showed that identical behavior resulted in all cases. - Highlights: • HAADF STEM imaging reveals the

  7. A sputnik IV saga

    Science.gov (United States)

    Lundquist, Charles A.

    2009-12-01

    The Sputnik IV launch occurred on May 15, 1960. On May 19, an attempt to deorbit a 'space cabin' failed and the cabin went into a higher orbit. The orbit of the cabin was monitored and Moonwatch volunteer satellite tracking teams were alerted to watch for the vehicle demise. On September 5, 1962, several team members from Milwaukee, Wisconsin made observations starting at 4:49 a.m. of a fireball following the predicted orbit of Sputnik IV. Requests went out to report any objects found under the fireball path. An early morning police patrol in Manitowoc had noticed a metal object on a street and had moved it to the curb. Later the officers recovered the object and had it dropped off at the Milwaukee Journal. The Moonwarch team got the object and reported the situation to Moonwatch Headquarters at the Smithsonian Astrophysical Observatory. A team member flew to Cambridge with the object. It was a solid, 9.49 kg piece of steel with a slag-like layer attached to it. Subsequent analyses showed that it contained radioactive nuclei produced by cosmic ray exposure in space. The scientists at the Observatory quickly recognized that measurements of its induced radioactivity could serve as a calibration for similar measurements of recently fallen nickel-iron meteorites. Concurrently, the Observatory directorate informed government agencies that a fragment from Sputnik IV had been recovered. Coincidently, a debate in the UN Committee on Peaceful Uses of Outer Space involved the issue of liability for damage caused by falling satellite fragments. On September 12, the Observatory delivered the bulk of the fragment to the US Delegation to the UN. Two days later, the fragment was used by US Ambassador Francis Plimpton as an exhibit that the time had come to agree on liability for damage from satellite debris. He offered the Sputnik IV fragment to USSR Ambassador P.D. Morozov, who refused the offer. On October 23, Drs. Alla Massevitch and E.K. Federov of the USSR visited the

  8. Numerical and dimensional investigation of two-phase countercurrent imbibition in porous media

    KAUST Repository

    El-Amin, Mohamed

    2013-04-01

    In this paper, we introduce a numerical solution of the problem of two-phase immiscible flow in porous media. In the first part of this work, we present the general conservation laws for multiphase flows in porous media as outlined in the literature for the sake of completion where we emphasize the difficulties associated with these equations in their primitive form and the fact that they are, generally, unclosed. The second part concerns the 1D computation for dimensional and non-dimensional cases and a theoretical analysis of the problem under consideration. A time-scale based on the characteristic velocity is used to transform the macroscopic governing equations into a non-dimensional form. The resulting dimensionless governing equations involved some important dimensionless physical parameters such as Bond number Bo, capillary number Ca and Darcy number Da. Numerical experiments on the Bond number effect is performed for two cases, gravity opposing and assisting. The theoretical analysis illustrates that common formulations of the time-scale forces the coefficient Da12Ca to be equal to one, while formulation of dimensionless time based on a characteristic velocity allows the capillary and Darcy numbers to appear in the dimensionless governing equation which leads to a wide range of scales and physical properties of fluids and rocks. The results indicate that the buoyancy effects due to gravity force take place depending on the location of the open boundary. © 2012 Elsevier B.V. All rights reserved.

  9. Investigation of vertical slug flow with advanced two-phase flow instrumentation

    International Nuclear Information System (INIS)

    Mi, Y.; Ishii, M.; Tsoukalas, L.H.<