WorldWideScience

Sample records for interventional robotics part

  1. Robotics in percutaneous cardiovascular interventions.

    Science.gov (United States)

    Pourdjabbar, Ali; Ang, Lawrence; Behnamfar, Omid; Patel, Mitul P; Reeves, Ryan R; Campbell, Paul T; Madder, Ryan D; Mahmud, Ehtisham

    2017-11-01

    The fundamental technique of performing percutaneous cardiovascular (CV) interventions has remained unchanged and requires operators to wear heavy lead aprons to minimize exposure to ionizing radiation. Robotic technology is now being utilized in interventional cardiology partially as a direct result of the increasing appreciation of the long-term occupational hazards of the field. This review was undertaken to report the clinical outcomes of percutaneous robotic coronary and peripheral vascular interventions. Areas covered: A systematic literature review of percutaneous robotic CV interventions was undertaken. The safety and feasibility of percutaneous robotically-assisted CV interventions has been validated in simple to complex coronary disease, and iliofemoral disease. Studies have shown that robotically-assisted PCI significantly reduces operator exposure to harmful ionizing radiation without compromising procedural success or clinical efficacy. In addition to the operator benefits, robotically-assisted intervention has the potential for patient advantages by allowing more accurate lesion length measurement, precise stent placement and lower patient radiation exposure. However, further investigation is required to fully elucidate these potential benefits. Expert commentary: Incremental improvement in robotic technology and telecommunications would enable treatment of an even broader patient population, and potentially provide remote robotic PCI.

  2. Composite Configuration Interventional Therapy Robot for the Microwave Ablation of Liver Tumors

    Science.gov (United States)

    Cao, Ying-Yu; Xue, Long; Qi, Bo-Jin; Jiang, Li-Pei; Deng, Shuang-Cheng; Liang, Ping; Liu, Jia

    2017-11-01

    The existing interventional therapy robots for the microwave ablation of liver tumors have a poor clinical applicability with a large volume, low positioning speed and complex automatic navigation control. To solve above problems, a composite configuration interventional therapy robot with passive and active joints is developed. The design of composite configuration reduces the size of the robot under the premise of a wide range of movement, and the robot with composite configuration can realizes rapid positioning with operation safety. The cumulative error of positioning is eliminated and the control complexity is reduced by decoupling active parts. The navigation algorithms for the robot are proposed based on solution of the inverse kinematics and geometric analysis. A simulation clinical test method is designed for the robot, and the functions of the robot and the navigation algorithms are verified by the test method. The mean error of navigation is 1.488 mm and the maximum error is 2.056 mm, and the positioning time for the ablation needle is in 10 s. The experimental results show that the designed robot can meet the clinical requirements for the microwave ablation of liver tumors. The composite configuration is proposed in development of the interventional therapy robot for the microwave ablation of liver tumors, which provides a new idea for the structural design of medical robots.

  3. The Development of Robotic Technology in Cardiac and Vascular Interventions

    Directory of Open Access Journals (Sweden)

    Ali Pourdjabbar

    2017-07-01

    Full Text Available Robotic technology has been used in cardiovascular medicine for over a decade, and over that period its use has been expanded to interventional cardiology and percutaneous coronary and peripheral vascular interventions. The safety and feasibility of robotically assisted interventions has been demonstrated in multiple studies ranging from simple to complex coronary lesions, and in the treatment of iliofemoral and infrapopliteal disease. These studies have shown a reduction in operator exposure to harmful ionizing radiation, and the use of robotics has the intuitive benefit of alleviating the occupational hazard of operator orthopedic injuries. In addition to the interventional operator benefits, robotically assisted intervention has the potential to also be beneficial for patients by allowing more accurate lesion length measurement, stent placement, and patient radiation exposure; however, more investigation is required to elucidate these benefits fully.

  4. Safety issues in robotic handling of nuclear weapon parts

    International Nuclear Information System (INIS)

    Drotning, W.; Wapman, W.; Fahrenholtz, J.

    1993-01-01

    Robotic systems are being developed by the Intelligent Systems and Robotics Center at Sandia National Laboratories to perform automated handling tasks with radioactive weapon parts. These systems will reduce the occupational radiation exposure to workers by automating operations that are currently performed manually. The robotic systems at Sandia incorporate several levels of mechanical, electrical, and software safety for handling hazardous materials. For example, tooling used by the robot to handle radioactive parts has been designed with mechanical features that allow the robot to release its payload only at designated locations in the robotic workspace. In addition, software processes check for expected and unexpected situations throughout the operations. Incorporation of features such as these provides multiple levels of safety for handling hazardous or valuable payloads with automated intelligent systems

  5. Interventional robotic systems: Applications and technology state-of-the-art

    Science.gov (United States)

    CLEARY, KEVIN; MELZER, ANDREAS; WATSON, VANCE; KRONREIF, GERNOT; STOIANOVICI, DAN

    2011-01-01

    Many different robotic systems have been developed for invasive medical procedures. In this article we will focus on robotic systems for image-guided interventions such as biopsy of suspicious lesions, interstitial tumor treatment, or needle placement for spinal blocks and neurolysis. Medical robotics is a young and evolving field and the ultimate role of these systems has yet to be determined. This paper presents four interventional robotics systems designed to work with MRI, CT, fluoroscopy, and ultrasound imaging devices. The details of each system are given along with any phantom, animal, or human trials. The systems include the AcuBot for active needle insertion under CT or fluoroscopy, the B-Rob systems for needle placement using CT or ultrasound, the INNOMOTION for MRI and CT interventions, and the MRBot for MRI procedures. Following these descriptions, the technology issues of image compatibility, registration, patient movement and respiration, force feedback, and control mode are briefly discussed. It is our belief that robotic systems will be an important part of future interventions, but more research and clinical trials are needed. The possibility of performing new clinical procedures that the human cannot achieve remains an ultimate goal for medical robotics. Engineers and physicians should work together to create and validate these systems for the benefits of patients everywhere. PMID:16754193

  6. Additive Manufacturing of Parts and Tooling in Robotic Systems

    Energy Technology Data Exchange (ETDEWEB)

    Love, Lonnie J. [ORNL; Hassen, Ahmed A. [ORNL; Chesser, Phillip C. [ORNL; Parsons, Jeremy [Mantaro Networks, Inc.

    2018-04-01

    ORNL worked with Transcend Robotics, LLC to explore additive manufacturing of the two-piece compression body for their ARTI mobile robot platform. Extrusion compression molding was identified as an effective means of manufacturing these parts. ORNL consulted on modifications to the housing design to accommodate the selected manufacturing process. Parts were printed using ORNL's FDM machines for testing and evaluation of the design as a precursor to molding the parts. The assembly and evaluation of the parts proved favorable and minor design changes to improve assembly and performance were identified.The goal is to develop a light weight and rugged two-part robotic enclosure for an unmanned ground vehicle UGV) that will be used in search and rescue applications. The FDM parts fabricated by ORNL allowed Transcend Robotics to assemble a prototype robot and verify that the new parts will meet the performance requirements. ORNL fabricated enclosure parts out of ABS and Nylon 12 materials such that the design could be tested prior to fabricating tooling for compression molding of Nylon 6 with carbon fiber fill. The robot was performance tested and compared with the previous manufacturing techniques and found to have superior performance.

  7. The use of robots for advanced intervention devices

    International Nuclear Information System (INIS)

    1981-01-01

    The main purpose of robots is to improve working conditions and to protect operators. Robots also enable interventions to be carried out in environments inaccessible to man. Extensive work carried out by the CEA in this field has led to the realization of equipment and original materials. Although, a lot of the development activities were initially related to nuclear work, a great diversity of applications have been found in other fields. Several applications are cited in this article; they are related to computer assisted remote controlled manipulators, remote controlled exploratory vehicles, robot medical equipment, and oceanographic research equipment [fr

  8. On the static structural design of climbing robots: part 1.

    Science.gov (United States)

    Ahmed, Ausama Hadi; Menon, Carlo

    This manuscript is the first of two parts of a work investigating optimal configurations of legged climbing robots while loitering on vertical surfaces. In this part 1, a mathematical model of a climbing robot based on the finite element method (FEM), specifically the stiffness method, is generated. A number of parameters, namely the height of the robot, the length of its body and the position of its legs, are investigated to assess their effect on the adhesion requirements needed for the robot to stay attached to a wall. Predictions of the developed mathematical model are validated using FEM commercial software. The body and the legs are assumed to be perpendicular to each other in this part 1. The effect of their inclination is investigated in the subsequent part 2 of our work. In part 2, the model is also used to predict postures that ants have while standing on vertical surfaces. The model is validated by comparing the predicted results to images of loitering ants. The parameters investigated provide guidelines to design legged climbing robots.

  9. Robotics

    International Nuclear Information System (INIS)

    Scheide, A.W.

    1983-01-01

    This article reviews some of the technical areas and history associated with robotics, provides information relative to the formation of a Robotics Industry Committee within the Industry Applications Society (IAS), and describes how all activities relating to robotics will be coordinated within the IEEE. Industrial robots are being used for material handling, processes such as coating and arc welding, and some mechanical and electronics assembly. An industrial robot is defined as a programmable, multifunctional manipulator designed to move material, parts, tools, or specialized devices through variable programmed motions for a variety of tasks. The initial focus of the Robotics Industry Committee will be on the application of robotics systems to the various industries that are represented within the IAS

  10. On the static structural design of climbing robots: part 2.

    Science.gov (United States)

    Ahmed, Ausama Hadi; Menon, Carlo

    This manuscript is the second of two parts of a work investigating optimal configurations of legged climbing robots while loitering on vertical surfaces. In this Part 2, a structural analysis based on the finite element method, specifically the stiffness method, is performed to address the problem. Parameters that are investigated in this Part 2 include the inclination of both the body and the legs of the robot. Outcomes of the performed study are validated by analyzing the posture of 150 ants when loitering on vertical surfaces. The obtained validation ensures the predictions of the developed structural model are correct and can be used to identify optimal configurations of legged robots when loitering on vertical surfaces.

  11. [Experimental study of angiography using vascular interventional robot-2(VIR-2)].

    Science.gov (United States)

    Tian, Zeng-min; Lu, Wang-sheng; Liu, Da; Wang, Da-ming; Guo, Shu-xiang; Xu, Wu-yi; Jia, Bo; Zhao, De-peng; Liu, Bo; Gao, Bao-feng

    2012-06-01

    To verify the feasibility and safety of new vascular interventional robot system used in vascular interventional procedures. Vascular interventional robot type-2 (VIR-2) included master-slave parts of body propulsion system, image navigation systems and force feedback system, the catheter movement could achieve under automatic control and navigation, force feedback was integrated real-time, followed by in vitro pre-test in vascular model and cerebral angiography in dog. Surgeon controlled vascular interventional robot remotely, the catheter was inserted into the intended target, the catheter positioning error and the operation time would be evaluated. In vitro pre-test and animal experiment went well; the catheter can enter any branch of vascular. Catheter positioning error was less than 1 mm. The angiography operation in animal was carried out smoothly without complication; the success rate of the operation was 100% and the entire experiment took 26 and 30 minutes, efficiency was slightly improved compared with the VIR-1, and the time what staff exposed to the DSA machine was 0 minute. The resistance of force sensor can be displayed to the operator to provide a security guarantee for the operation. No surgical complications. VIR-2 is safe and feasible, and can achieve the catheter remote operation and angiography; the master-slave system meets the characteristics of traditional procedure. The three-dimensional image can guide the operation more smoothly; force feedback device provides remote real-time haptic information to provide security for the operation.

  12. Study on real-time force feedback for a master-slave interventional surgical robotic system.

    Science.gov (United States)

    Guo, Shuxiang; Wang, Yuan; Xiao, Nan; Li, Youxiang; Jiang, Yuhua

    2018-04-13

    In robot-assisted catheterization, haptic feedback is important, but is currently lacking. In addition, conventional interventional surgical robotic systems typically employ a master-slave architecture with an open-loop force feedback, which results in inaccurate control. We develop herein a novel real-time master-slave (RTMS) interventional surgical robotic system with a closed-loop force feedback that allows a surgeon to sense the true force during remote operation, provide adequate haptic feedback, and improve control accuracy in robot-assisted catheterization. As part of this system, we also design a unique master control handle that measures the true force felt by a surgeon, providing the basis for the closed-loop control of the entire system. We use theoretical and empirical methods to demonstrate that the proposed RTMS system provides a surgeon (using the master control handle) with a more accurate and realistic force sensation, which subsequently improves the precision of the master-slave manipulation. The experimental results show a substantial increase in the control accuracy of the force feedback and an increase in operational efficiency during surgery.

  13. An affordable compact humanoid robot for Autism Spectrum Disorder interventions in children.

    Science.gov (United States)

    Dickstein-Fischer, Laurie; Alexander, Elizabeth; Yan, Xiaoan; Su, Hao; Harrington, Kevin; Fischer, Gregory S

    2011-01-01

    Autism Spectrum Disorder impacts an ever-increasing number of children. The disorder is marked by social functioning that is characterized by impairment in the use of nonverbal behaviors, failure to develop appropriate peer relationships and lack of social and emotional exchanges. Providing early intervention through the modality of play therapy has been effective in improving behavioral and social outcomes for children with autism. Interacting with humanoid robots that provide simple emotional response and interaction has been shown to improve the communication skills of autistic children. In particular, early intervention and continuous care provide significantly better outcomes. Currently, there are no robots capable of meeting these requirements that are both low-cost and available to families of autistic children for in-home use. This paper proposes the piloting the use of robotics as an improved diagnostic and early intervention tool for autistic children that is affordable, non-threatening, durable, and capable of interacting with an autistic child. This robot has the ability to track the child with its 3 degree of freedom (DOF) eyes and 3-DOF head, open and close its 1-DOF beak and 1-DOF each eyelids, raise its 1-DOF each wings, play sound, and record sound. These attributes will give it the ability to be used for the diagnosis and treatment of autism. As part of this project, the robot and the electronic and control software have been developed, and integrating semi-autonomous interaction, teleoperation from a remote healthcare provider and initiating trials with children in a local clinic are in progress.

  14. Remote radiation mapping and preliminary intervention using collaborating (European and Russian) mobile robots

    International Nuclear Information System (INIS)

    Piotrowski, L.; Trouville, B.; Halbach, M.; Sidorkin, N.

    1996-12-01

    The primary objective of the IMPACT project is to develop a light-weight and inexpensive mobile robot that can be used for rapid inspection missions within nuclear power plants. These interventions are to cover normal, incident and accident situations and aim at primary reconnaissance (or 'data collecting') missions. The IMPACT robot was demonstrated (April 1996) in a realistic mission at the Russian nuclear plant SMOLENSK. The demonstration, composed of 2 independent but consecutive missions, was held in a radioactive zone near turbine ≠ 4 of Unit 2: remote radiation mapping with localisation of radioactive sources by the IMPACT robot equipped with a (Russian) gamma-radiation sensor; deployment of a Russian intervention robot for the construction of a protective lead shield around one of the identified sources and verification that the ambient radiation level has been reduce. This mission was executed remotely by 2 mobile robots working in collaboration: a NIKIMT robot equipped with a manipulator arm and carrying leads bricks and the IMPACT robot of mission I (radiation measurements and 'side-observer'). This manuscript describes (a) the technical characteristics of the IMPACT reconnaissance robot (3-segmented, caterpillar-tracked body; 6 video cameras placed around the mobile platform with simultaneous presentation of up to 4 video images at the control post; ability to detach remotely one of the robot's segments (i.e. the robot can divide itself into 2 separate mobile robots)) and (b) the SMOLENSK demonstration. (author)

  15. Industrial dual arm robot manipulator for precise assembly of mechanical parts

    Science.gov (United States)

    Park, Chanhun; Kim, Doohyung; Park, Kyoungtaik; Choi, Youngjin

    2007-12-01

    A new structure of dual arm robot manipulator which consists of two industrial 6-DOF arms and one 2-DOF Torso is introduced. Each industrial 6-DOF arm is able to be used as a stand-alone industrial 6-DOF robot manipulator and as a part of dual arm manipulator at the same time. These structures help the robot maker which is willing to succeed in the emerging dual arm robot market in order to have high competition for the current industrial robot market at same time. Self-collision detection algorithm for multi-arm robot and kinematics algorithms for the developed dual arm robot manipulator which are implemented in our controller are introduced.

  16. KNOWLEDGE-BASED ROBOT VISION SYSTEM FOR AUTOMATED PART HANDLING

    Directory of Open Access Journals (Sweden)

    J. Wang

    2012-01-01

    Full Text Available

    ENGLISH ABSTRACT: This paper discusses an algorithm incorporating a knowledge-based vision system into an industrial robot system for handling parts intelligently. A continuous fuzzy controller was employed to extract boundary information in a computationally efficient way. The developed algorithm for on-line part recognition using fuzzy logic is shown to be an effective solution to extract the geometric features of objects. The proposed edge vector representation method provides enough geometric information and facilitates the object geometric reconstruction for gripping planning. Furthermore, a part-handling model was created by extracting the grasp features from the geometric features.

    AFRIKAANSE OPSOMMING: Hierdie artikel beskryf ‘n kennis-gebaseerde visiesisteemalgoritme wat in ’n industriёle robotsisteem ingesluit word om sodoende intelligente komponenthantering te bewerkstellig. ’n Kontinue wasige beheerder is gebruik om allerlei objekinligting deur middel van ’n effektiewe berekeningsmetode te bepaal. Die ontwikkelde algoritme vir aan-lyn komponentherkenning maak gebruik van wasige logika en word bewys as ’n effektiewe metode om geometriese inligting van objekte te bepaal. Die voorgestelde grensvektormetode verskaf voldoende inligting en maak geometriese rekonstruksie van die objek moontlik om greepbeplanning te kan doen. Voorts is ’n komponenthanteringsmodel ontwikkel deur die grypkenmerke af te lei uit die geometriese eienskappe.

  17. Robotics

    Science.gov (United States)

    Popov, E. P.; Iurevich, E. I.

    The history and the current status of robotics are reviewed, as are the design, operation, and principal applications of industrial robots. Attention is given to programmable robots, robots with adaptive control and elements of artificial intelligence, and remotely controlled robots. The applications of robots discussed include mechanical engineering, cargo handling during transportation and storage, mining, and metallurgy. The future prospects of robotics are briefly outlined.

  18. A Genetic Algorithm-based Heuristic for Part-Feeding Mobile Robot Scheduling Problem

    DEFF Research Database (Denmark)

    Dang, Vinh Quang; Nielsen, Izabela Ewa; Bocewicz, Grzegorz

    2012-01-01

    This present study deals with the problem of sequencing feeding tasks of a single mobile robot with manipulation arm which is able to provide parts or components for feeders of machines in a manufacturing cell. The mobile robot has to be scheduled in order to keep machines within the cell producing...... products without any shortage of parts. A method based on the characteristics of feeders and inspired by the (s, Q) inventory system, is thus applied to define time windows for feeding tasks of the robot. The performance criterion is to minimize total traveling time of the robot in a given planning horizon...

  19. A Fully Sensorized Cooperative Robotic System for Surgical Interventions

    Science.gov (United States)

    Tovar-Arriaga, Saúl; Vargas, José Emilio; Ramos, Juan M.; Aceves, Marco A.; Gorrostieta, Efren; Kalender, Willi A.

    2012-01-01

    In this research a fully sensorized cooperative robot system for manipulation of needles is presented. The setup consists of a DLR/KUKA Light Weight Robot III especially designed for safe human/robot interaction, a FD-CT robot-driven angiographic C-arm system, and a navigation camera. Also, new control strategies for robot manipulation in the clinical environment are introduced. A method for fast calibration of the involved components and the preliminary accuracy tests of the whole possible errors chain are presented. Calibration of the robot with the navigation system has a residual error of 0.81 mm (rms) with a standard deviation of ±0.41 mm. The accuracy of the robotic system while targeting fixed points at different positions within the workspace is of 1.2 mm (rms) with a standard deviation of ±0.4 mm. After calibration, and due to close loop control, the absolute positioning accuracy was reduced to the navigation camera accuracy which is of 0.35 mm (rms). The implemented control allows the robot to compensate for small patient movements. PMID:23012551

  20. Accuracy and speed of robotic assisted needle interventions using a modern cone beam computed tomography intervention suite: a phantom study

    Energy Technology Data Exchange (ETDEWEB)

    Schulz, Boris [Goethe University Hospital, Institute for Diagnostic and Interventional Radiology, Frankfurt (Germany); Goethe University Hospital, Department of Diagnostic and Interventional Radiology, Frankfurt (Germany); Eichler, Katrin; Siebenhandl, Petra; Gruber-Rouh, Tatjana; Vogl, Thomas Josef; Zangos, Stephan [Goethe University Hospital, Institute for Diagnostic and Interventional Radiology, Frankfurt (Germany); Czerny, Christoph [Goethe University Hospital, Department of Trauma Surgery, Frankfurt (Germany)

    2013-01-15

    To analyse the feasibility and accuracy of robotic aided interventions on a phantom when using a modern C-arm-mounted cone beam computed tomography (CBCT) device in combination with needle guidance software. A small robotic device capable of holding and guiding needles was attached to the intervention table. After acquiring a 3D data set the access path was planned on the CBCT workstation and shown on the intervention monitor. Then the robot was aligned to the live fluoroscopic image. A total of 40 punctures were randomly conducted on a phantom armed with several targets (diameter 2 mm) in single and double oblique trajectory (n = 20 each). Target distance, needle deviation and time for the procedures were analysed. All phantom interventions (n = 40) could be performed successfully. Mean target access path within the phantom was 8.5 cm (min 4.2 cm, max 13.5 cm). Average needle tip deviation was 1.1 mm (min 0 mm, max 4.5 mm), time duration was 3:59 min (min 2:07 min, max 10:37 min). When using the proposed robot device in a CBCT intervention suite, highly accurate needle-based interventional punctures are possible in a reasonable timely manner in single as well as in double oblique trajectories. (orig.)

  1. Accuracy and speed of robotic assisted needle interventions using a modern cone beam computed tomography intervention suite: a phantom study

    International Nuclear Information System (INIS)

    Schulz, Boris; Eichler, Katrin; Siebenhandl, Petra; Gruber-Rouh, Tatjana; Vogl, Thomas Josef; Zangos, Stephan; Czerny, Christoph

    2013-01-01

    To analyse the feasibility and accuracy of robotic aided interventions on a phantom when using a modern C-arm-mounted cone beam computed tomography (CBCT) device in combination with needle guidance software. A small robotic device capable of holding and guiding needles was attached to the intervention table. After acquiring a 3D data set the access path was planned on the CBCT workstation and shown on the intervention monitor. Then the robot was aligned to the live fluoroscopic image. A total of 40 punctures were randomly conducted on a phantom armed with several targets (diameter 2 mm) in single and double oblique trajectory (n = 20 each). Target distance, needle deviation and time for the procedures were analysed. All phantom interventions (n = 40) could be performed successfully. Mean target access path within the phantom was 8.5 cm (min 4.2 cm, max 13.5 cm). Average needle tip deviation was 1.1 mm (min 0 mm, max 4.5 mm), time duration was 3:59 min (min 2:07 min, max 10:37 min). When using the proposed robot device in a CBCT intervention suite, highly accurate needle-based interventional punctures are possible in a reasonable timely manner in single as well as in double oblique trajectories. (orig.)

  2. Long-reach articulated robots for inspection and mini-invasive interventions in hazardous environments: Recent robotics research, qualification testing, and tool developments

    International Nuclear Information System (INIS)

    Perrot, Yann; Kammerer, Nolwenn; Measson, Yvan; Verney, Alexandre; Gargiulo, Laurent; Houry, Michael; Keller, Delphine; Piolain, Gerard

    2012-01-01

    The Interactive Robotics Laboratory of CEA LIST is in charge of the development of remote handling technologies to meet energy industry requirements. This paper reports the research and development activities in advanced robotics systems for inspection or light intervention in hazardous environments with limited access such as blind hot cells in the nuclear industry or the thermonuclear experimental Tokamak fusion reactor. A long-reach carrier robot called the articulated inspection arm (AIA) and diagnostics and tools for inspection or intervention are described. Finally experimental field tests are presented and actual challenges in modeling the robot's flexibilities are discussed. (authors)

  3. Design and Performance Evaluation of Real-time Endovascular Interventional Surgical Robotic System with High Accuracy.

    Science.gov (United States)

    Wang, Kundong; Chen, Bing; Lu, Qingsheng; Li, Hongbing; Liu, Manhua; Shen, Yu; Xu, Zhuoyan

    2018-05-15

    Endovascular interventional surgery (EIS) is performed under a high radiation environment at the sacrifice of surgeons' health. This paper introduces a novel endovascular interventional surgical robot that aims to reduce radiation to surgeons and physical stress imposed by lead aprons during fluoroscopic X-ray guided catheter intervention. The unique mechanical structure allowed the surgeon to manipulate the axial and radial motion of the catheter and guide wire. Four catheter manipulators (to manipulate the catheter and guide wire), and a control console which consists of four joysticks, several buttons and two twist switches (to control the catheter manipulators) were presented. The entire robotic system was established on a master-slave control structure through CAN (Controller Area Network) bus communication, meanwhile, the slave side of this robotic system showed highly accurate control over velocity and displacement with PID controlling method. The robotic system was tested and passed in vitro and animal experiments. Through functionality evaluation, the manipulators were able to complete interventional surgical motion both independently and cooperatively. The robotic surgery was performed successfully in an adult female pig and demonstrated the feasibility of superior mesenteric and common iliac artery stent implantation. The entire robotic system met the clinical requirements of EIS. The results show that the system has the ability to imitate the movements of surgeons and to accomplish the axial and radial motions with consistency and high-accuracy. Copyright © 2018 John Wiley & Sons, Ltd.

  4. Microsurgery robots: addressing the needs of high-precision surgical interventions.

    Science.gov (United States)

    Mattos, Leonardo S; Caldwell, Darwin G; Peretti, Giorgio; Mora, Francesco; Guastini, Luca; Cingolani, Roberto

    2016-01-01

    Robotics has a significant potential to enhance the overall capacity and efficiency of healthcare systems. Robots can help surgeons perform better quality operations, leading to reductions in the hospitalisation time of patients and in the impact of surgery on their postoperative quality of life. In particular, robotics can have a significant impact on microsurgery, which presents stringent requirements for superhuman precision and control of the surgical tools. Microsurgery is, in fact, expected to gain importance in a growing range of surgical specialties as novel technologies progressively enable the detection, diagnosis and treatment of diseases at earlier stages. Within such scenarios, robotic microsurgery emerges as one of the key components of future surgical interventions, and will be a vital technology for addressing major surgical challenges. Nonetheless, several issues have yet to be overcome in terms of mechatronics, perception and surgeon-robot interfaces before microsurgical robots can achieve their full potential in operating rooms. Research in this direction is progressing quickly and microsurgery robot prototypes are gradually demonstrating significant clinical benefits in challenging applications such as reconstructive plastic surgery, ophthalmology, otology and laryngology. These are reassuring results offering confidence in a brighter future for high-precision surgical interventions.

  5. Pneumatically Operated MRI-Compatible Needle Placement Robot for Prostate Interventions.

    Science.gov (United States)

    Fischer, Gregory S; Iordachita, Iulian; Csoma, Csaba; Tokuda, Junichi; Mewes, Philip W; Tempany, Clare M; Hata, Nobuhiko; Fichtinger, Gabor

    2008-06-13

    Magnetic Resonance Imaging (MRI) has potential to be a superior medical imaging modality for guiding and monitoring prostatic interventions. The strong magnetic field prevents the use of conventional mechatronics and the confined physical space makes it extremely challenging to access the patient. We have designed a robotic assistant system that overcomes these difficulties and promises safe and reliable intra-prostatic needle placement inside closed high-field MRI scanners. The robot performs needle insertion under real-time 3T MR image guidance; workspace requirements, MR compatibility, and workflow have been evaluated on phantoms. The paper explains the robot mechanism and controller design and presents results of preliminary evaluation of the system.

  6. Long-term interventions effects of robotic training on patients after anterior cruciate ligament reconstruction

    OpenAIRE

    Hu, Chunying; Huang, Qiuchen; Yu, Lili; Zhou, Yue; Gu, Rui; Ye, Miao; Ge, Meng; Xu, Yanfeng; Liu, Jianfeng

    2016-01-01

    [Purpose] The aim of this study was to examine the long-term interventions effects of robot-assisted therapy rehabilitation on functional activity levels after anterior cruciate ligament reconstruction. [Subjects and Methods] The subjects were 8 patients (6 males and 2 females) who received anterior cruciate ligament reconstruction. The subjects participated in robot-assisted therapy lasting for one month. The Timed Up-and-Go test, 10-Meter Walk test, Functional Reach Test, surface electromyo...

  7. Pneumatically Operated MRI-Compatible Needle Placement Robot for Prostate Interventions

    OpenAIRE

    Fischer, Gregory S.; Iordachita, Iulian; Csoma, Csaba; Tokuda, Junichi; Mewes, Philip W.; Tempany, Clare M.; Hata, Nobuhiko; Fichtinger, Gabor

    2008-01-01

    Magnetic Resonance Imaging (MRI) has potential to be a superior medical imaging modality for guiding and monitoring prostatic interventions. The strong magnetic field prevents the use of conventional mechatronics and the confined physical space makes it extremely challenging to access the patient. We have designed a robotic assistant system that overcomes these difficulties and promises safe and reliable intra-prostatic needle placement inside closed high-field MRI scanners. The robot perform...

  8. Fast and Efficient Radiological Interventions via a Graphical User Interface Commanded Magnetic Resonance Compatible Robotic Device

    Science.gov (United States)

    Özcan, Alpay; Christoforou, Eftychios; Brown, Daniel; Tsekos, Nikolaos

    2011-01-01

    The graphical user interface for an MR compatible robotic device has the capability of displaying oblique MR slices in 2D and a 3D virtual environment along with the representation of the robotic arm in order to swiftly complete the intervention. Using the advantages of the MR modality the device saves time and effort, is safer for the medical staff and is more comfortable for the patient. PMID:17946067

  9. How to Implement Robots in Interventions for Children with Autism? A Co-Creation Study Involving People with Autism, Parents and Professionals

    Science.gov (United States)

    Huijnen, Claire A. G. J.; Lexis, Monique A. S.; Jansens, Rianne; de Witte, Luc P.

    2017-01-01

    The aim of this study was to gain insight into how robots can be practically implemented into current education and therapy interventions for children with autism spectrum disorder (ASD). This qualitative study included focus groups and co-creation sessions. 73 Participants (professionals and adults with ASD) took part in 13 focus groups to elicit…

  10. Long-term interventions effects of robotic training on patients after anterior cruciate ligament reconstruction.

    Science.gov (United States)

    Hu, Chunying; Huang, Qiuchen; Yu, Lili; Zhou, Yue; Gu, Rui; Ye, Miao; Ge, Meng; Xu, Yanfeng; Liu, Jianfeng

    2016-08-01

    [Purpose] The aim of this study was to examine the long-term interventions effects of robot-assisted therapy rehabilitation on functional activity levels after anterior cruciate ligament reconstruction. [Subjects and Methods] The subjects were 8 patients (6 males and 2 females) who received anterior cruciate ligament reconstruction. The subjects participated in robot-assisted therapy lasting for one month. The Timed Up-and-Go test, 10-Meter Walk test, Functional Reach Test, surface electromyography of the vastus lateralis and vastus medialis, and extensor strength of isokinetic movement of the knee joint were evaluated before and after the intervention. [Results] The average value of the of vastus medialis EMG, Functional Reach Test, and the maximum and average extensor strength of the knee joint isokinetic movement increased significantly, and the time of the 10-Meter Walk test decreased significantly. [Conclusion] These results suggest that walking ability and muscle strength can be improved by robotic walking training as a long-term intervention.

  11. Designing HRD Interventions for Employee-Robot Interaction

    Science.gov (United States)

    Heo, Se Jin

    2011-01-01

    The purpose of this study was to identify critical causes of work stress and job satisfaction of nurses, which can contribute to find appropriate organizational supports to help nurses effectively work with a surgical robot. Delphi method was employed to identify the critical stressors and the key causes of job satisfaction of nurses working with…

  12. The intervention of robot caregivers and the cultivation of children's capability to play.

    Science.gov (United States)

    Pearson, Yvette; Borenstein, Jason

    2013-03-01

    In this article, the authors examine whether and how robot caregivers can contribute to the welfare of children with various cognitive and physical impairments by expanding recreational opportunities for these children. The capabilities approach is used as a basis for informing the relevant discussion. Though important in its own right, having the opportunity to play is essential to the development of other capabilities central to human flourishing. Drawing from empirical studies, the authors show that the use of various types of robots has already helped some children with impairments. Recognizing the potential ethical pitfalls of robot caregiver intervention, however, the authors examine these concerns and conclude that an appropriately designed robot caregiver has the potential to contribute positively to the development of the capability to play while also enhancing the ability of human caregivers to understand and interact with care recipients.

  13. The immediate intervention effects of robotic training in patients after anterior cruciate ligament reconstruction.

    Science.gov (United States)

    Hu, Chunying; Huang, Qiuchen; Yu, Lili; Ye, Miao

    2016-07-01

    [Purpose] The purpose of this study was to examine the immediate effects of robot-assisted therapy on functional activity level after anterior cruciate ligament reconstruction. [Subjects and Methods] Participants included 10 patients (8 males and 2 females) following anterior cruciate ligament reconstruction. The subjects participated in robot-assisted therapy and treadmill exercise on different days. The Timed Up-and-Go test, Functional Reach Test, surface electromyography of the vastus lateralis and vastus medialis, and maximal extensor strength of isokinetic movement of the knee joint were evaluated in both groups before and after the experiment. [Results] The results for the Timed Up-and-Go Test and the 10-Meter Walk Test improved in the robot-assisted rehabilitation group. Surface electromyography of the vastus medialis muscle showed significant increases in maximum and average discharge after the intervention. [Conclusion] The results suggest that walking ability and muscle strength can be improved by robotic training.

  14. Remote ultrasound palpation for robotic interventions using absolute elastography.

    Science.gov (United States)

    Schneider, Caitlin; Baghani, Ali; Rohling, Robert; Salcudean, Septimiu

    2012-01-01

    Although robotic surgery has addressed many of the challenges presented by minimally invasive surgery, haptic feedback and the lack of knowledge of tissue stiffness is an unsolved problem. This paper presents a system for finding the absolute elastic properties of tissue using a freehand ultrasound scanning technique, which utilizes the da Vinci Surgical robot and a custom 2D ultrasound transducer for intraoperative use. An external exciter creates shear waves in the tissue, and a local frequency estimation method computes the shear modulus. Results are reported for both phantom and in vivo models. This system can be extended to any 6 degree-of-freedom tracking method and any 2D transducer to provide real-time absolute elastic properties of tissue.

  15. Analytical basis for evaluating the effect of unplanned interventions on the effectiveness of a human-robot system

    International Nuclear Information System (INIS)

    Shah, Julie A.; Saleh, Joseph H.; Hoffman, Jeffrey A.

    2008-01-01

    Increasing prevalence of human-robot systems in a variety of applications raises the question of how to design these systems to best leverage the capabilities of humans and robots. In this paper, we address the relationships between reliability, productivity, and risk to humans from human-robot systems operating in a hostile environment. Objectives for maximizing the effectiveness of a human-robot system are presented, which capture these coupled relationships, and reliability parameters are proposed to characterize unplanned interventions between a human and robot. The reliability metrics defined here take on an expanded meaning in which the underlying concept of failure in traditional reliability analysis is replaced by the notion of intervention. In the context of human-robotic systems, an intervention is not only driven by component failures, but includes many other factors that can make a robotic agent to request or a human agent to provide intervention, as we argue in this paper. The effect of unplanned interventions on the effectiveness of human-robot systems is then investigated analytically using traditional reliability analysis. Finally, we discuss the implications of these analytical trends on the design and evaluation of human-robot systems

  16. Robotics

    Energy Technology Data Exchange (ETDEWEB)

    Lorino, P; Altwegg, J M

    1985-05-01

    This article, which is aimed at the general reader, examines latest developments in, and the role of, modern robotics. The 7 main sections are sub-divided into 27 papers presented by 30 authors. The sections are as follows: 1) The role of robotics, 2) Robotics in the business world and what it can offer, 3) Study and development, 4) Utilisation, 5) Wages, 6) Conditions for success, and 7) Technological dynamics.

  17. Pneumatically Operated MRI-Compatible Needle Placement Robot for Prostate Interventions

    Science.gov (United States)

    Fischer, Gregory S.; Iordachita, Iulian; Csoma, Csaba; Tokuda, Junichi; Mewes, Philip W.; Tempany, Clare M.; Hata, Nobuhiko; Fichtinger, Gabor

    2011-01-01

    Magnetic Resonance Imaging (MRI) has potential to be a superior medical imaging modality for guiding and monitoring prostatic interventions. The strong magnetic field prevents the use of conventional mechatronics and the confined physical space makes it extremely challenging to access the patient. We have designed a robotic assistant system that overcomes these difficulties and promises safe and reliable intra-prostatic needle placement inside closed high-field MRI scanners. The robot performs needle insertion under real-time 3T MR image guidance; workspace requirements, MR compatibility, and workflow have been evaluated on phantoms. The paper explains the robot mechanism and controller design and presents results of preliminary evaluation of the system. PMID:21686038

  18. A new AS-display as part of the MIRO lightweight robot for surgical applications

    Science.gov (United States)

    Grossmann, Christoph M.

    2010-02-01

    The DLR MIRO is the second generation of versatile robot arms for surgical applications, developed at the Institute for Robotics and Mechatronics at Deutsche Zentrum für Luft- und Raumfahrt (DLR) in Oberpfaffenhofen, Germany. With its low weight of 10 kg and dimensions similar to those of the human arm, the MIRO robot can assist the surgeon directly at the operating table where space is scarce. The planned scope of applications of this robot arm ranges from guiding a laser unit for the precise separation of bone tissue in orthopedics to positioning holes for bone screws, robot assisted endoscope guidance and on to the multi-robot concept for endoscopic minimally invasive surgery. A stereo-endoscope delivers two full HD video streams that can even be augmented with information, e.g vectors indicating the forces that act on the surgical tool at any given moment. SeeFront's new autostereoscopic 3D display SF 2223, being a part of the MIRO assembly, will let the surgeon view the stereo video stream in excellent quality, in real time and without the need for any viewing aids. The presentation is meant to provide an insight into the principles at the basis of the SeeFront 3D technology and how they allow the creation of autostereoscopic display solutions ranging from smallest "stamp-sized" displays to 30" desktop versions, which all provide comfortable freedom of movement for the viewer along with excellent 3D image quality.

  19. Influence of part orientation on the geometric accuracy in robot-based incremental sheet metal forming

    Science.gov (United States)

    Störkle, Denis Daniel; Seim, Patrick; Thyssen, Lars; Kuhlenkötter, Bernd

    2016-10-01

    This article describes new developments in an incremental, robot-based sheet metal forming process (`Roboforming') for the production of sheet metal components for small lot sizes and prototypes. The dieless kinematic-based generation of the shape is implemented by means of two industrial robots, which are interconnected to a cooperating robot system. Compared to other incremental sheet metal forming (ISF) machines, this system offers high geometrical form flexibility without the need of any part-dependent tools. The industrial application of ISF is still limited by certain constraints, e.g. the low geometrical accuracy. Responding to these constraints, the authors present the influence of the part orientation and the forming sequence on the geometric accuracy. Their influence is illustrated with the help of various experimental results shown and interpreted within this article.

  20. Impact of robotics and a suspended lead suit on physician radiation exposure during percutaneous coronary intervention

    Energy Technology Data Exchange (ETDEWEB)

    Madder, Ryan D., E-mail: ryan.madder@spectrumhealth.org; VanOosterhout, Stacie; Mulder, Abbey; Elmore, Matthew; Campbell, Jessica; Borgman, Andrew; Parker, Jessica; Wohns, David

    2017-04-15

    Background: Reports of left-sided brain malignancies among interventional cardiologists have heightened concerns regarding physician radiation exposure. This study evaluated the impact of a suspended lead suit and robotic system on physician radiation exposure during percutaneous coronary intervention (PCI). Methods: Real-time radiation exposure data were prospectively collected from dosimeters worn by operating physicians at the head- and chest-level during consecutive PCI cases. Exposures were compared in three study groups: 1) manual PCI performed with traditional lead apparel; 2) manual PCI performed using suspended lead; and 3) robotic PCI performed in combination with suspended lead. Results: Among 336 cases (86.6% manual, 13.4% robotic) performed over 30 weeks, use of suspended lead during manual PCI was associated with significantly less radiation exposure to the chest and head of operating physicians than traditional lead apparel (chest: 0.0 [0.1] μSv vs 0.4 [4.0] μSv, p < 0.001; head: 0.5 [1.9] μSv vs 14.9 [51.5] μSv, p < 0.001). Chest-level radiation exposure during robotic PCI performed in combination with suspended lead was 0.0 [0.0] μSv, which was significantly less chest exposure than manual PCI performed with traditional lead (p < 0.001) or suspended lead (p = 0.046). In robotic PCI the median head-level exposure was 0.1 [0.2] μSv, which was 99.3% less than manual PCI performed with traditional lead (p < 0.001) and 80.0% less than manual PCI performed with suspended lead (p < 0.001). Conclusions: Utilization of suspended lead and robotics were observed to result in significantly less radiation exposure to the chest and head of operating physicians during PCI. - Highlights: • Use of suspended lead during manual PCI reduced cranial radiation among operators by 97%. • Robotic PCI reduced cranial radiation among operators by 99%. • Suspended lead and robotics together achieved the lowest levels of radiation exposure.

  1. Impact of robotics and a suspended lead suit on physician radiation exposure during percutaneous coronary intervention

    International Nuclear Information System (INIS)

    Madder, Ryan D.; VanOosterhout, Stacie; Mulder, Abbey; Elmore, Matthew; Campbell, Jessica; Borgman, Andrew; Parker, Jessica; Wohns, David

    2017-01-01

    Background: Reports of left-sided brain malignancies among interventional cardiologists have heightened concerns regarding physician radiation exposure. This study evaluated the impact of a suspended lead suit and robotic system on physician radiation exposure during percutaneous coronary intervention (PCI). Methods: Real-time radiation exposure data were prospectively collected from dosimeters worn by operating physicians at the head- and chest-level during consecutive PCI cases. Exposures were compared in three study groups: 1) manual PCI performed with traditional lead apparel; 2) manual PCI performed using suspended lead; and 3) robotic PCI performed in combination with suspended lead. Results: Among 336 cases (86.6% manual, 13.4% robotic) performed over 30 weeks, use of suspended lead during manual PCI was associated with significantly less radiation exposure to the chest and head of operating physicians than traditional lead apparel (chest: 0.0 [0.1] μSv vs 0.4 [4.0] μSv, p < 0.001; head: 0.5 [1.9] μSv vs 14.9 [51.5] μSv, p < 0.001). Chest-level radiation exposure during robotic PCI performed in combination with suspended lead was 0.0 [0.0] μSv, which was significantly less chest exposure than manual PCI performed with traditional lead (p < 0.001) or suspended lead (p = 0.046). In robotic PCI the median head-level exposure was 0.1 [0.2] μSv, which was 99.3% less than manual PCI performed with traditional lead (p < 0.001) and 80.0% less than manual PCI performed with suspended lead (p < 0.001). Conclusions: Utilization of suspended lead and robotics were observed to result in significantly less radiation exposure to the chest and head of operating physicians during PCI. - Highlights: • Use of suspended lead during manual PCI reduced cranial radiation among operators by 97%. • Robotic PCI reduced cranial radiation among operators by 99%. • Suspended lead and robotics together achieved the lowest levels of radiation exposure.

  2. Advanced composite alloys for constructional parts of robots

    Science.gov (United States)

    Issin, D. K.; Zholdubayeva, Zh D.; Neshina, Y. G.; Alkina, A. D.; Khuangan, N.; Rahimova, G. M.

    2018-05-01

    In recent years all over the world special attention has been paid to the development and implementation of nanostructured materials possessing unique properties and opening fascinating prospects for the development of technical progress in various fields of human activities. A special place can be given to the development of service robots, the market of which is actively developing. There is problem associated mainly with the lack of heat-strengthened alloys which consists in low thermal stability of the alloy properties under the conditions of elevated variable temperatures and loads. The article presents studies to assess the effect of composition, the amounts of refractory nanoscale particles and methods for their introduction into the melt on the structure and properties in nanostructured composite aluminum alloys. The powders of metals, alloys, as well as silicon carbide and aluminum oxide were used to produce the nanostructured powder composite materials. As a result of the research, NPCM compositions containing micro-size particles of transition metals that are carriers of nanosized reinforcing particles and initiators of the formation of an intermetallide of endogenous origin in a melt.

  3. Ergonomic deficits in robotic gynecologic oncology surgery: a need for intervention.

    Science.gov (United States)

    Craven, Renatta; Franasiak, Jason; Mosaly, Prithima; Gehrig, Paola A

    2013-01-01

    To evaluate surgeon strain using validated ergonomic assessment tools. Observational study (Canadian Task Force classification III). Academic medical center. Robotic surgeons performing gynecologic oncology surgical procedures. Videotape footage of surgeons performing robotic gynecologic oncology procedures was obtained. A human factors engineer experienced with health care ergonomics analyzed the video recordings and performed ergonomic evaluations of the surgeons. An initial evaluation was conducted using the Rapid Upper Limb Assessment (RULA) survey, an ergonomic assessment and prioritization method for determining posture, force, and frequency concerns with focus on the upper limbs. A more detailed analysis followed using the Strain Index (SI) method, which uses multiplicative interactions to identify jobs that are potentially hazardous. Seventeen hours of video recordings were analyzed, and descriptive data based on RULA/SI analysis were collected. Ergonomic evaluation of surgeon activity resulted in a mean RULA score of 6.46 (maximum possible RULA score, 7), indicating a need for further investigation. The mean SI grand score was 24.34. SI scores >10 suggest a potential for hazard to the operator. Thus, the current use of the surgical robot is potentially dangerous with regards to ergonomic positioning and should be modified. At a high-volume robotics center, there are ergonomics deficits that are hazardous to gynecologic surgeons and suggest the need for modification and intervention. A training strategy must be developed to address these ergonomic issues and knowledge deficiencies. Copyright © 2013 AAGL. Published by Elsevier Inc. All rights reserved.

  4. Impact of robotics and a suspended lead suit on physician radiation exposure during percutaneous coronary intervention.

    Science.gov (United States)

    Madder, Ryan D; VanOosterhout, Stacie; Mulder, Abbey; Elmore, Matthew; Campbell, Jessica; Borgman, Andrew; Parker, Jessica; Wohns, David

    Reports of left-sided brain malignancies among interventional cardiologists have heightened concerns regarding physician radiation exposure. This study evaluated the impact of a suspended lead suit and robotic system on physician radiation exposure during percutaneous coronary intervention (PCI). Real-time radiation exposure data were prospectively collected from dosimeters worn by operating physicians at the head- and chest-level during consecutive PCI cases. Exposures were compared in three study groups: 1) manual PCI performed with traditional lead apparel; 2) manual PCI performed using suspended lead; and 3) robotic PCI performed in combination with suspended lead. Among 336 cases (86.6% manual, 13.4% robotic) performed over 30weeks, use of suspended lead during manual PCI was associated with significantly less radiation exposure to the chest and head of operating physicians than traditional lead apparel (chest: 0.0 [0.1] μSv vs 0.4 [4.0] μSv, probotic PCI performed in combination with suspended lead was 0.0 [0.0] μSv, which was significantly less chest exposure than manual PCI performed with traditional lead (probotic PCI the median head-level exposure was 0.1 [0.2] μSv, which was 99.3% less than manual PCI performed with traditional lead (probotics were observed to result in significantly less radiation exposure to the chest and head of operating physicians during PCI. Copyright © 2016 Elsevier Inc. All rights reserved.

  5. Robotics

    Indian Academy of Sciences (India)

    netic induction to detect an object. The development of ... end effector, inclination of object, magnetic and electric fields, etc. The sensors described ... In the case of a robot, the various actuators and motors have to be modelled. The major ...

  6. MRI-guided robotic system for transperineal prostate interventions: proof of principle

    International Nuclear Information System (INIS)

    Van den Bosch, Michiel R; Moman, Maaike R; Van Vulpen, Marco; Battermann, Jan J; Lagendijk, Jan J W; Moerland, Marinus A; Duiveman, Ed; Van Schelven, Leonard J; De Leeuw, Hendrik

    2010-01-01

    In this study, we demonstrate the proof of principle of the University Medical Center Utrecht (UMCU) robot dedicated to magnetic resonance imaging (MRI)-guided interventions in patients. The UMCU robot consists of polymers and non-ferromagnetic materials. For transperineal prostate interventions, it can be placed between the patient's legs inside a closed bore 1.5T MR scanner. The robot can manually be translated and rotated resulting in five degrees of freedom. It contains a pneumatically driven tapping device to automatically insert a needle stepwise into the prostate using a controller unit outside the scanning room. To define the target positions and to verify the needle insertion point and the needle trajectory, a high-resolution 3D balanced steady state free precession (bSSFP) scan that provides a T2/T1-weighted contrast is acquired. During the needle insertion fast 2D bSSFP images are generated to track the needle on-line. When the target position is reached, the radiation oncologist manually places a fiducial gold marker (small seed) at this location. In total two needle trajectories are used to place all markers. Afterwards, a high-resolution 3D bSSFP scan is acquired to visualize the fiducial gold markers. Four fiducial gold markers were placed transperineally into the prostate of a patient with a clinical stage T3 prostate cancer. In the generated scans, it was possible to discriminate the patient's anatomy, the needle and the markers. All markers were delivered inside the prostate. The procedure time was 1.5 h. This study proves that MRI-guided needle placement and seed delivery in the prostate with the UMCU robot are feasible. (note)

  7. MRI-guided robotic system for transperineal prostate interventions: proof of principle

    Energy Technology Data Exchange (ETDEWEB)

    Van den Bosch, Michiel R; Moman, Maaike R; Van Vulpen, Marco; Battermann, Jan J; Lagendijk, Jan J W; Moerland, Marinus A [Department of Radiotherapy, University Medical Center Utrecht, Heidelberglaan 100, 3584 CX, Utrecht (Netherlands); Duiveman, Ed; Van Schelven, Leonard J [Medical Technology and Clinical Physics, University Medical Center Utrecht, Heidelberglaan 100, 3584 CX, Utrecht (Netherlands); De Leeuw, Hendrik [Image Sciences Institute, University Medical Center Utrecht, Heidelberglaan 100, 3584 CX, Utrecht (Netherlands)], E-mail: M.R.vandenBosch@umcutrecht.nl

    2010-03-07

    In this study, we demonstrate the proof of principle of the University Medical Center Utrecht (UMCU) robot dedicated to magnetic resonance imaging (MRI)-guided interventions in patients. The UMCU robot consists of polymers and non-ferromagnetic materials. For transperineal prostate interventions, it can be placed between the patient's legs inside a closed bore 1.5T MR scanner. The robot can manually be translated and rotated resulting in five degrees of freedom. It contains a pneumatically driven tapping device to automatically insert a needle stepwise into the prostate using a controller unit outside the scanning room. To define the target positions and to verify the needle insertion point and the needle trajectory, a high-resolution 3D balanced steady state free precession (bSSFP) scan that provides a T2/T1-weighted contrast is acquired. During the needle insertion fast 2D bSSFP images are generated to track the needle on-line. When the target position is reached, the radiation oncologist manually places a fiducial gold marker (small seed) at this location. In total two needle trajectories are used to place all markers. Afterwards, a high-resolution 3D bSSFP scan is acquired to visualize the fiducial gold markers. Four fiducial gold markers were placed transperineally into the prostate of a patient with a clinical stage T3 prostate cancer. In the generated scans, it was possible to discriminate the patient's anatomy, the needle and the markers. All markers were delivered inside the prostate. The procedure time was 1.5 h. This study proves that MRI-guided needle placement and seed delivery in the prostate with the UMCU robot are feasible. (note)

  8. Promoting question-asking in school-aged children with autism spectrum disorders : effectiveness of a robot intervention compared to a human-trainer intervention

    NARCIS (Netherlands)

    Huskens, Bibi; Verschuur, R.; Gillesen, J.C.C.; Didden, R.; Barakova, E.I.

    2013-01-01

    Objective: The purpose of the present study was to investigate the effectiveness of an applied behaviour analysis (ABA)-based intervention conducted by a robot compared to an ABA-based intervention conducted by a human trainer in promoting self-initiated questions in children with autism spectrum

  9. 75 FR 68613 - Part C Early Intervention Services Grant

    Science.gov (United States)

    2010-11-08

    ... DEPARTMENT OF HEALTH AND HUMAN SERVICES Health Resources and Services Administration Part C Early Intervention Services Grant AGENCY: Health Resources and Services Administration (HRSA), HHS. ACTION: Notice of non-competitive transfer of Part C funds from North General Hospital to the Institute for Family...

  10. An Online Change of Activity in Energy Spectrum for Detection on an Early Intervention Robot

    Energy Technology Data Exchange (ETDEWEB)

    Boudergui, K.; Laine, F. [CEA, LIST, Laboratoire Capteurs et Architectures Electroniques, F-91191 Gif Sur Yvette (France); Montagu, T. [CEA, LIST, Laboratoire de Modelisation et de Simulation des Systemes, 91191 Gif-sur-Yvette (France); Blanc, P. [IMS, Innovation and Measurement Systems, 94100 Saint-Maur-des-Fosses (France); Deltour, A. [ECA Robotics, 91892 Orsay Cedex (France); Mozziconacci, S. [SDIS13, 13110 Port de Bouc (France)

    2015-07-01

    With the growth of industrial risks and the multiplication of CBRNe (Chemical Biological Radiological and explosive) attacks through toxic chemicals, biological or radiological threats, public services and military authorities face with increasingly critical situations, whose management is strongly conditioned by fast and reliable establishment of an informative diagnostic. Right after an attack, the five first minutes are crucial to define the various scenarios and the most dangerous for a human intervention. Therefore the use of robots is considered essential by all stakeholders of security. In this context, the SISPEO project (Systeme d'Intervention Sapeurs Pompiers Robotise) aims to create/build/design a robust response through a robotic platform for early intervention services such as civil and military security in hostile environments. CEA LIST has proposed an adapted solution to detect and characterize nuclear and radiological risks online and in motion, using a miniature embedded CdZnTe (CZT) crystal Gamma-ray spectrometer. This paper presents experimental results for this miniature embedded CZT spectrometer and its associated mathematical method to detect and characterize radiological threats online and in motion. (authors)

  11. An Online Change of Activity in Energy Spectrum for Detection on an Early Intervention Robot

    International Nuclear Information System (INIS)

    Boudergui, K.; Laine, F.; Montagu, T.; Blanc, P.; Deltour, A.; Mozziconacci, S.

    2015-01-01

    With the growth of industrial risks and the multiplication of CBRNe (Chemical Biological Radiological and explosive) attacks through toxic chemicals, biological or radiological threats, public services and military authorities face with increasingly critical situations, whose management is strongly conditioned by fast and reliable establishment of an informative diagnostic. Right after an attack, the five first minutes are crucial to define the various scenarios and the most dangerous for a human intervention. Therefore the use of robots is considered essential by all stakeholders of security. In this context, the SISPEO project (Systeme d'Intervention Sapeurs Pompiers Robotise) aims to create/build/design a robust response through a robotic platform for early intervention services such as civil and military security in hostile environments. CEA LIST has proposed an adapted solution to detect and characterize nuclear and radiological risks online and in motion, using a miniature embedded CdZnTe (CZT) crystal Gamma-ray spectrometer. This paper presents experimental results for this miniature embedded CZT spectrometer and its associated mathematical method to detect and characterize radiological threats online and in motion. (authors)

  12. Intraocular robotic interventional surgical system (IRISS): Mechanical design, evaluation, and master-slave manipulation.

    Science.gov (United States)

    Wilson, Jason T; Gerber, Matthew J; Prince, Stephen W; Chen, Cheng-Wei; Schwartz, Steven D; Hubschman, Jean-Pierre; Tsao, Tsu-Chin

    2018-02-01

    Since the advent of robotic-assisted surgery, the value of using robotic systems to assist in surgical procedures has been repeatedly demonstrated. However, existing technologies are unable to perform complete, multi-step procedures from start to finish. Many intraocular surgical steps continue to be manually performed. An intraocular robotic interventional surgical system (IRISS) capable of performing various intraocular surgical procedures was designed, fabricated, and evaluated. Methods were developed to evaluate the performance of the remote centers of motion (RCMs) using a stereo-camera setup and to assess the accuracy and precision of positioning the tool tip using an optical coherence tomography (OCT) system. The IRISS can simultaneously manipulate multiple surgical instruments, change between mounted tools using an onboard tool-change mechanism, and visualize the otherwise invisible RCMs to facilitate alignment of the RCM to the surgical incision. The accuracy of positioning the tool tip was measured to be 0.205±0.003 mm. The IRISS was evaluated by trained surgeons in a remote surgical theatre using post-mortem pig eyes and shown to be effective in completing many key steps in a variety of intraocular surgical procedures as well as being capable of performing an entire cataract extraction from start to finish. The IRISS represents a necessary step towards fully automated intraocular surgery and demonstrated accurate and precise master-slave manipulation for cataract removal and-through visual feedback-retinal vein cannulation. Copyright © 2017 John Wiley & Sons, Ltd.

  13. EFSUMB Guidelines on Interventional Ultrasound (INVUS), Part IV - EUS-guided interventions

    DEFF Research Database (Denmark)

    Jenssen, C; Hocke, M; Fusaroli, P

    2016-01-01

    The fourth part of the European Federation of Societies for Ultrasound in Medicine and Biology (EFSUMB) Guidelines on Interventional Ultrasound describes general aspects of endoscopic ultrasound-guided diagnostic and therapeutic interventions and assesses the evidence for endoscopic ultrasound-gu...

  14. In vivo bioprinting for computer- and robotic-assisted medical intervention: preliminary study in mice

    International Nuclear Information System (INIS)

    Keriquel, Virginie; Guillemot, Fabien; Arnault, Isabelle; Guillotin, Bertrand; Amedee, Joelle; Fricain, Jean-Christophe; Catros, Sylvain; Miraux, Sylvain

    2010-01-01

    We present the first attempt to apply bioprinting technologies in the perspective of computer-assisted medical interventions. A workstation dedicated to high-throughput biological laser printing has been designed. Nano-hydroxyapatite (n-HA) was printed in the mouse calvaria defect model in vivo. Critical size bone defects were performed in OF-1 male mice calvaria with a 4 mm diameter trephine. Prior to laser printing experiments, the absence of inflammation due to laser irradiation onto mice dura mater was shown by means of magnetic resonance imaging. Procedures for in vivo bioprinting and results obtained using decalcified sections and x-ray microtomography are discussed. Although heterogeneous, these preliminary results demonstrate that in vivo bioprinting is possible. Bioprinting may prove to be helpful in the future for medical robotics and computer-assisted medical interventions.

  15. In vivo bioprinting for computer- and robotic-assisted medical intervention: preliminary study in mice

    Energy Technology Data Exchange (ETDEWEB)

    Keriquel, Virginie; Guillemot, Fabien; Arnault, Isabelle; Guillotin, Bertrand; Amedee, Joelle; Fricain, Jean-Christophe; Catros, Sylvain [INSERM, U577, Bordeaux, F-33076 (France) and Universite Victor Segalen Bordeaux 2, UMR-S577 Bordeaux, F-33076 (France); Miraux, Sylvain [Centre de Resonance Magnetique des Systemes Biologiques, UMR 5536 (France)

    2010-03-15

    We present the first attempt to apply bioprinting technologies in the perspective of computer-assisted medical interventions. A workstation dedicated to high-throughput biological laser printing has been designed. Nano-hydroxyapatite (n-HA) was printed in the mouse calvaria defect model in vivo. Critical size bone defects were performed in OF-1 male mice calvaria with a 4 mm diameter trephine. Prior to laser printing experiments, the absence of inflammation due to laser irradiation onto mice dura mater was shown by means of magnetic resonance imaging. Procedures for in vivo bioprinting and results obtained using decalcified sections and x-ray microtomography are discussed. Although heterogeneous, these preliminary results demonstrate that in vivo bioprinting is possible. Bioprinting may prove to be helpful in the future for medical robotics and computer-assisted medical interventions.

  16. A linear stepping endovascular intervention robot with variable stiffness and force sensing.

    Science.gov (United States)

    He, Chengbin; Wang, Shuxin; Zuo, Siyang

    2018-03-08

    Robotic-assisted endovascular intervention surgery has attracted significant attention and interest in recent years. However, limited designs have focused on the variable stiffness mechanism of the catheter shaft. Flexible catheter needs to be partially switched to a rigid state that can hold its shape against external force to achieve a stable and effective insertion procedure. Furthermore, driving catheter in a similar way with manual procedures has the potential to make full use of the extensive experience from conventional catheter navigation. Besides driving method, force sensing is another significant factor for endovascular intervention. This paper presents a variable stiffness catheterization system that can provide stable and accurate endovascular intervention procedure with a linear stepping mechanism that has a similar operation mode to the conventional catheter navigation. A specially designed shape-memory polymer tube with water cooling structure is used to achieve variable stiffness of the catheter. Hence, four FBG sensors are attached to the catheter tip in order to monitor the tip contact force situation with temperature compensation. Experimental results show that the actuation unit is able to deliver linear and rotational motions. We have shown the feasibility of FBG force sensing to reduce the effect of temperature and detect the tip contact force. The designed catheter can change its stiffness partially, and the stiffness of the catheter can be remarkably increased in rigid state. Hence, in the rigid state, the catheter can hold its shape against a [Formula: see text] load. The prototype has also been validated with a vascular phantom, demonstrating the potential clinical value of the system. The proposed system provides important insights into the design of compact robotic-assisted catheter incorporating effective variable stiffness mechanism and real-time force sensing for intraoperative endovascular intervention.

  17. Nanotechnology and its relationship to interventional radiology. Part I: imaging.

    LENUS (Irish Health Repository)

    Power, Sarah

    2011-04-01

    Nanotechnology refers to the design, creation, and manipulation of structures on the nanometer scale. Interventional radiology stands to benefit greatly from advances in nanotechnology because much of the ongoing research is focused toward novel methods of imaging and delivery of therapy through minimally invasive means. Through the development of new techniques and therapies, nanotechnology has the potential to broaden the horizon of interventional radiology and ensure its continued success. This two-part review is intended to acquaint the interventionalist with the field of nanotechnology, and provide an overview of potential applications, while highlighting advances relevant to interventional radiology. Part I of the article deals with an introduction to some of the basic concepts of nanotechnology and outlines some of the potential imaging applications, concentrating mainly on advances in oncological and vascular imaging.

  18. Nanotechnology and its relationship to interventional radiology. Part I: imaging.

    LENUS (Irish Health Repository)

    Power, Sarah

    2012-02-01

    Nanotechnology refers to the design, creation, and manipulation of structures on the nanometer scale. Interventional radiology stands to benefit greatly from advances in nanotechnology because much of the ongoing research is focused toward novel methods of imaging and delivery of therapy through minimally invasive means. Through the development of new techniques and therapies, nanotechnology has the potential to broaden the horizon of interventional radiology and ensure its continued success. This two-part review is intended to acquaint the interventionalist with the field of nanotechnology, and provide an overview of potential applications, while highlighting advances relevant to interventional radiology. Part I of the article deals with an introduction to some of the basic concepts of nanotechnology and outlines some of the potential imaging applications, concentrating mainly on advances in oncological and vascular imaging.

  19. Nanotechnology and its Relationship to Interventional Radiology. Part I: Imaging

    International Nuclear Information System (INIS)

    Power, Sarah; Slattery, Michael M.; Lee, Michael J.

    2011-01-01

    Nanotechnology refers to the design, creation, and manipulation of structures on the nanometer scale. Interventional radiology stands to benefit greatly from advances in nanotechnology because much of the ongoing research is focused toward novel methods of imaging and delivery of therapy through minimally invasive means. Through the development of new techniques and therapies, nanotechnology has the potential to broaden the horizon of interventional radiology and ensure its continued success. This two-part review is intended to acquaint the interventionalist with the field of nanotechnology, and provide an overview of potential applications, while highlighting advances relevant to interventional radiology. Part I of the article deals with an introduction to some of the basic concepts of nanotechnology and outlines some of the potential imaging applications, concentrating mainly on advances in oncological and vascular imaging.

  20. Magnetic resonance-compatible robotic and mechatronics systems for image-guided interventions and rehabilitation: a review study.

    Science.gov (United States)

    Tsekos, Nikolaos V; Khanicheh, Azadeh; Christoforou, Eftychios; Mavroidis, Constantinos

    2007-01-01

    The continuous technological progress of magnetic resonance imaging (MRI), as well as its widespread clinical use as a highly sensitive tool in diagnostics and advanced brain research, has brought a high demand for the development of magnetic resonance (MR)-compatible robotic/mechatronic systems. Revolutionary robots guided by real-time three-dimensional (3-D)-MRI allow reliable and precise minimally invasive interventions with relatively short recovery times. Dedicated robotic interfaces used in conjunction with fMRI allow neuroscientists to investigate the brain mechanisms of manipulation and motor learning, as well as to improve rehabilitation therapies. This paper gives an overview of the motivation, advantages, technical challenges, and existing prototypes for MR-compatible robotic/mechatronic devices.

  1. Modelling of a biologically inspired robotic fish driven by compliant parts

    International Nuclear Information System (INIS)

    Daou, Hadi El; Salumäe, Taavi; Kruusmaa, Maarja; Chambers, Lily D; Megill, William M

    2014-01-01

    Inspired by biological swimmers such as fish, a robot composed of a rigid head, a compliant body and a rigid caudal fin was built. It has the geometrical properties of a subcarangiform swimmer of the same size. The head houses a servo-motor which actuates the compliant body and the caudal fin. It achieves this by applying a concentrated moment on a point near the compliant body base. In this paper, the dynamics of the compliant body driving the robotic fish is modelled and experimentally validated. Lighthill’s elongated body theory is used to define the hydrodynamic forces on the compliant part and Rayleigh proportional damping is used to model damping. Based on the assumed modes method, an energetic approach is used to write the equations of motion of the compliant body and to compute the relationship between the applied moment and the resulting lateral deflections. Experiments on the compliant body were carried out to validate the model predictions. The results showed that a good match was achieved between the measured and predicted deformations. A discussion of the swimming motions between the real fish and the robot is presented. (paper)

  2. Quality of life after percutaneous coronary intervention: part 1.

    Science.gov (United States)

    Cassar, Stephen; R Baldacchino, Donia

    Quality of life (QOL) is a complex concept comprised of biopsychosocial, spiritual and environmental dimensions. However, the majority of research addresses only its physical function perspectives. This two-part series examines the holistic perspective of QOL of patients after percutaneous coronary intervention (PCI). Part 1 explains the research process of a cross-sectional descriptive study and its limitations. Data were collected by a mailed WHOQOL-BREF questionnaire in Maltese from a systematic sample of patients who had undergone PCI; the response rate was 64% (n=228; males n=169, females n=59, age 40-89 years). Part 1 also considers limitations, such as its cross-sectional design and retrospective data collection. The hierarchy of human needs theory (Maslow, 1999) guided the study. Part 2 gives the findings on the holistic view of QOL. Having social and family support, as a characteristic of Maltese culture appeared to contribute towards a better QOL.

  3. Visual servoing in medical robotics: a survey. Part II: tomographic imaging modalities--techniques and applications.

    Science.gov (United States)

    Azizian, Mahdi; Najmaei, Nima; Khoshnam, Mahta; Patel, Rajni

    2015-03-01

    Intraoperative application of tomographic imaging techniques provides a means of visual servoing for objects beneath the surface of organs. The focus of this survey is on therapeutic and diagnostic medical applications where tomographic imaging is used in visual servoing. To this end, a comprehensive search of the electronic databases was completed for the period 2000-2013. Existing techniques and products are categorized and studied, based on the imaging modality and their medical applications. This part complements Part I of the survey, which covers visual servoing techniques using endoscopic imaging and direct vision. The main challenges in using visual servoing based on tomographic images have been identified. 'Supervised automation of medical robotics' is found to be a major trend in this field and ultrasound is the most commonly used tomographic modality for visual servoing. Copyright © 2014 John Wiley & Sons, Ltd.

  4. Nanotechnology and its relationship to interventional radiology. Part II: Drug Delivery, Thermotherapy, and Vascular Intervention.

    LENUS (Irish Health Repository)

    Power, Sarah

    2012-02-01

    Nanotechnology can be defined as the design, creation, and manipulation of structures on the nanometer scale. This two-part review is intended to acquaint the interventionalist with the field of nanotechnology, and provide an overview of potential applications, while highlighting advances relevant to interventional radiology. Part 2 of the article concentrates on drug delivery, thermotherapy, and vascular intervention. In oncology, advances in drug delivery allow for improved efficacy, decreased toxicity, and greater potential for targeted therapy. Magnetic nanoparticles show potential for use in thermotherapy treatments of various tumours, and the effectiveness of radiofrequency ablation can be enhanced with nanoparticle chemotherapy agents. In vascular intervention, much work is focused on prevention of restenosis through developments in stent technology and systems for localised drug delivery to vessel walls. Further areas of interest include applications for thrombolysis and haemostasis.

  5. Nanotechnology and its Relationship to Interventional Radiology. Part II: Drug Delivery, Thermotherapy, and Vascular Intervention.

    LENUS (Irish Health Repository)

    Power, Sarah

    2010-09-16

    Nanotechnology can be defined as the design, creation, and manipulation of structures on the nanometer scale. This two-part review is intended to acquaint the interventionalist with the field of nanotechnology, and provide an overview of potential applications, while highlighting advances relevant to interventional radiology. Part 2 of the article concentrates on drug delivery, thermotherapy, and vascular intervention. In oncology, advances in drug delivery allow for improved efficacy, decreased toxicity, and greater potential for targeted therapy. Magnetic nanoparticles show potential for use in thermotherapy treatments of various tumours, and the effectiveness of radiofrequency ablation can be enhanced with nanoparticle chemotherapy agents. In vascular intervention, much work is focused on prevention of restenosis through developments in stent technology and systems for localised drug delivery to vessel walls. Further areas of interest include applications for thrombolysis and haemostasis.

  6. Lapabot: a compact telesurgical robot system for minimally invasive surgery: part II. Telesurgery evaluation.

    Science.gov (United States)

    Park, Jun Woo; Lee, Duck Hee; Kim, Young Woo; Lee, Byeong Han; Jo, Yung Ho

    2012-05-01

    As described in Part I, the Lapabot was developed considering telesurgery from the initial design stage. The robot configuration is based on the master-slave structure in which the operator can be separated spatially from the patient. The distributed control architecture communicating through high-speed network enables remote control of surgical robot manipulators. In this work, we added network communication modules using user datagram protocol/internet protocol for implementation of the telesurgical system. For a stable network environment, a dedicated research network was adopted. To characterize the network environment, a data packet sender and a repeater whose packet length and packet structure are similar to those of the real data packet were developed. The developed system was evaluated through in-vitro and in-vivo experiments. With the developed system, we have successfully performed remote control of the Lapabot. The roundtrip time delay for the control signal ranged from 1.4 to 4.1 ms. The total time delay for the operator including image signal acquisition and transmission delays was under 333 ms. It did not impede surgical procedures. Initial evaluation results demonstrate the feasibility of the developed telesurgical system.

  7. Treatment and technical intervention time analysis of a robotic stereotactic radiotherapy system.

    Science.gov (United States)

    Crop, F; Lacornerie, T; Szymczak, H; Felin, A; Bailleux, C; Mirabel, X; Lartigau, E

    2014-02-01

    The purpose of this study is to obtain a better operational knowledge of Stereotactic Body Radiotherapy (SBRT) treatments with CyberKnife(r). An analysis of both In-room Times (IRT) and technical interventions of 5 years of treatments was performed, during which more than 1600 patients were treated for various indications, including liver (21%), lung (29%), intracranial (13%), head and neck (11%) and prostate (7%). Technical interventions were recorded along with the time of the failure, time to the intervention, and the complexity and duration of the repair. Analyses of Time Between Failures (TBF) and Service Disrupting TBF(disr) were performed. Treatment time data and variability per indication and following different system upgrades were evaluated. Large variations of IRTs were found between indications, but also large variations for each indication. The combination of the time reduction Tool (using Iris(r)) and Improved Stop Handling was of major impact to shortening of treatment times. The first implementation of the Iris collimator alone did not lead to significantly shorter IRTs for us except during prostate treatments. This was mostly due to the addition at the same time of larger rotational compensation for prostate treatments (58 instead of 1.58). Significant differences of duration between the first fraction and following fractions of a treatment, representing the necessity of defining imaging parameters and explanation to patients, were found for liver (12 min) and lung treatments using Xsight(r) Spine (5 min). Liver and lung treatments represent the longest IRT's and involve the largest variability's in IRT. The malfunction rate of the system followed a Weibull distribution with the shape and scale parameters of 0.8 and 39.7. Mean TBF(disr) was 68 work hours. 60 to 80% of the service disrupting interventions were resolved within 30-60 min, 5% required external intervention and 30% occurred in the morning. The presented results can be applied in the

  8. Preclinical evaluation of an MRI-compatible pneumatic robot for angulated needle placement in transperineal prostate interventions

    Science.gov (United States)

    Tokuda, Junichi; Song, Sang-Eun; Fischer, Gregory S.; Iordachita, Iulian; Seifabadi, Reza; Cho, Bong Joon; Tuncali, Kemal; Fichtinger, Gabor; Tempany, Clare M.; Hata, Nobuhiko

    2013-01-01

    Purpose To evaluate the targeting accuracy of a small profile MRI-compatible pneumatic robot for needle placement that can angulate a needle insertion path into a large accessible target volume. Methods We extended our MRI-compatible pneumatic robot for needle placement to utilize its four degrees-of-freedom (4-DOF) mechanism with two parallel triangular structures and support transperineal prostate biopsies in a closed-bore magnetic resonance imaging (MRI) scanner. The robot is designed to guide a needle towards a lesion so that a radiologist can manually insert it in the bore. The robot is integrated with navigation software that allows an operator to plan angulated needle insertion by selecting a target and an entry point. The targeting error was evaluated while the angle between the needle insertion path and the static magnetic field was between −5.7° and 5.7° horizontally and between −5.7° and 4.3° vertically in the MRI scanner after sterilizing and draping the device. Results The robot positioned the needle for angulated insertion as specified on the navigation software with overall targeting error of 0.8 ± 0.5 mm along the horizontal axis and 0.8 ± 0.8 mm along the vertical axis. The two-dimensional root-mean-square targeting error on the axial slices as containing the targets was 1.4 mm. Conclusions Our preclinical evaluation demonstrated that the MRI-compatible pneumatic robot for needle placement with the capability to angulate the needle insertion path provides targeting accuracy feasible for clinical MRI-guided prostate interventions. The clinical feasibility has to be established in a clinical study. PMID:22678723

  9. A Model Based Approach to Increase the Part Accuracy in Robot Based Incremental Sheet Metal Forming

    International Nuclear Information System (INIS)

    Meier, Horst; Laurischkat, Roman; Zhu Junhong

    2011-01-01

    One main influence on the dimensional accuracy in robot based incremental sheet metal forming results from the compliance of the involved robot structures. Compared to conventional machine tools the low stiffness of the robot's kinematic results in a significant deviation of the planned tool path and therefore in a shape of insufficient quality. To predict and compensate these deviations offline, a model based approach, consisting of a finite element approach, to simulate the sheet forming, and a multi body system, modeling the compliant robot structure, has been developed. This paper describes the implementation and experimental verification of the multi body system model and its included compensation method.

  10. Probabilistic scan mode of a robot manipulator workspace using EEG signals. Part I

    International Nuclear Information System (INIS)

    Auat Cheein, Fernando A; Di Sciascio, Fernando; Freire Bastos, Teodiano; Carelli, Ricardo

    2007-01-01

    In this paper a probabilistic-based workspace scan mode of a manipulator robot is presented. The scan mode is governed by a Brain Computer Interface (BCI) based on Event Related Potentials (Synchronization and Dessynchronization events). The user is capable to select a specific position at the robot's workspace, which should be reached by the manipulator. The robot workspace is divided into cells. Each cell has a probability value associated with it. Once the robot reaches a cell, its probability value is updated. The mode the scan is made is determined by the probability of all cells at the workspace. Finally, the manipulator is teleoperated via TCP/IP

  11. Visual servoing in medical robotics: a survey. Part I: endoscopic and direct vision imaging - techniques and applications.

    Science.gov (United States)

    Azizian, Mahdi; Khoshnam, Mahta; Najmaei, Nima; Patel, Rajni V

    2014-09-01

    Intra-operative imaging is widely used to provide visual feedback to a clinician when he/she performs a procedure. In visual servoing, surgical instruments and parts of tissue/body are tracked by processing the acquired images. This information is then used within a control loop to manoeuvre a robotic manipulator during a procedure. A comprehensive search of electronic databases was completed for the period 2000-2013 to provide a survey of the visual servoing applications in medical robotics. The focus is on medical applications where image-based tracking is used for closed-loop control of a robotic system. Detailed classification and comparative study of various contributions in visual servoing using endoscopic or direct visual images are presented and summarized in tables and diagrams. The main challenges in using visual servoing for medical robotic applications are identified and potential future directions are suggested. 'Supervised automation of medical robotics' is found to be a major trend in this field. Copyright © 2013 John Wiley & Sons, Ltd.

  12. Robotics education

    International Nuclear Information System (INIS)

    Benton, O.

    1984-01-01

    Robotics education courses are rapidly spreading throughout the nation's colleges and universities. Engineering schools are offering robotics courses as part of their mechanical or manufacturing engineering degree program. Two year colleges are developing an Associate Degree in robotics. In addition to regular courses, colleges are offering seminars in robotics and related fields. These seminars draw excellent participation at costs running up to $200 per day for each participant. The last one drew 275 people from Texas to Virginia. Seminars are also offered by trade associations, private consulting firms, and robot vendors. IBM, for example, has the Robotic Assembly Institute in Boca Raton and charges about $1,000 per week for course. This is basically for owners of IBM robots. Education (and training) can be as short as one day or as long as two years. Here is the educational pattern that is developing now

  13. Integration and evaluation of a needle-positioning robot with volumetric microcomputed tomography image guidance for small animal stereotactic interventions

    International Nuclear Information System (INIS)

    Waspe, Adam C.; McErlain, David D.; Pitelka, Vasek; Holdsworth, David W.; Lacefield, James C.; Fenster, Aaron

    2010-01-01

    Purpose: Preclinical research protocols often require insertion of needles to specific targets within small animal brains. To target biologically relevant locations in rodent brains more effectively, a robotic device has been developed that is capable of positioning a needle along oblique trajectories through a single burr hole in the skull under volumetric microcomputed tomography (micro-CT) guidance. Methods: An x-ray compatible stereotactic frame secures the head throughout the procedure using a bite bar, nose clamp, and ear bars. CT-to-robot registration enables structures identified in the image to be mapped to physical coordinates in the brain. Registration is accomplished by injecting a barium sulfate contrast agent as the robot withdraws the needle from predefined points in a phantom. Registration accuracy is affected by the robot-positioning error and is assessed by measuring the surface registration error for the fiducial and target needle tracks (FRE and TRE). This system was demonstrated in situ by injecting 200 μm tungsten beads into rat brains along oblique trajectories through a single burr hole on the top of the skull under micro-CT image guidance. Postintervention micro-CT images of each skull were registered with preintervention high-field magnetic resonance images of the brain to infer the anatomical locations of the beads. Results: Registration using four fiducial needle tracks and one target track produced a FRE and a TRE of 96 and 210 μm, respectively. Evaluation with tissue-mimicking gelatin phantoms showed that locations could be targeted with a mean error of 154±113 μm. Conclusions: The integration of a robotic needle-positioning device with volumetric micro-CT image guidance should increase the accuracy and reduce the invasiveness of stereotactic needle interventions in small animals.

  14. Integration and evaluation of a needle-positioning robot with volumetric microcomputed tomography image guidance for small animal stereotactic interventions

    Energy Technology Data Exchange (ETDEWEB)

    Waspe, Adam C.; McErlain, David D.; Pitelka, Vasek; Holdsworth, David W.; Lacefield, James C.; Fenster, Aaron [Biomedical Engineering Graduate Program and Imaging Research Laboratories, Robarts Research Institute, University of Western Ontario, London, Ontario N6A 5K8 (Canada); Department of Medical Biophysics and Imaging Research Laboratories, Robarts Research Institute, University of Western Ontario, London, Ontario N6A 5K8 (Canada); Department of Physiology and Pharmacology, University of Western Ontario, London, Ontario N6A 5C1 (Canada); Biomedical Engineering Graduate Program, Department of Medical Biophysics, Department of Medical Imaging, Department of Surgery, and Imaging Research Laboratories, Robarts Research Institute, University of Western Ontario, London, Ontario N6A 5K8 (Canada); Biomedical Engineering Graduate Program, Department of Electrical and Computer Engineering, Department of Medical Biophysics, and Imaging Research Laboratories, Robarts Research Institute, University of Western Ontario, London, Ontario N6A 5K8 (Canada); Biomedical Engineering Graduate Program, Department of Medical Biophysics, Department of Medical Imaging, and Imaging Research Laboratories, Robarts Research Institute, University of Western Ontario, London, Ontario N6A 5K8 (Canada)

    2010-04-15

    Purpose: Preclinical research protocols often require insertion of needles to specific targets within small animal brains. To target biologically relevant locations in rodent brains more effectively, a robotic device has been developed that is capable of positioning a needle along oblique trajectories through a single burr hole in the skull under volumetric microcomputed tomography (micro-CT) guidance. Methods: An x-ray compatible stereotactic frame secures the head throughout the procedure using a bite bar, nose clamp, and ear bars. CT-to-robot registration enables structures identified in the image to be mapped to physical coordinates in the brain. Registration is accomplished by injecting a barium sulfate contrast agent as the robot withdraws the needle from predefined points in a phantom. Registration accuracy is affected by the robot-positioning error and is assessed by measuring the surface registration error for the fiducial and target needle tracks (FRE and TRE). This system was demonstrated in situ by injecting 200 {mu}m tungsten beads into rat brains along oblique trajectories through a single burr hole on the top of the skull under micro-CT image guidance. Postintervention micro-CT images of each skull were registered with preintervention high-field magnetic resonance images of the brain to infer the anatomical locations of the beads. Results: Registration using four fiducial needle tracks and one target track produced a FRE and a TRE of 96 and 210 {mu}m, respectively. Evaluation with tissue-mimicking gelatin phantoms showed that locations could be targeted with a mean error of 154{+-}113 {mu}m. Conclusions: The integration of a robotic needle-positioning device with volumetric micro-CT image guidance should increase the accuracy and reduce the invasiveness of stereotactic needle interventions in small animals.

  15. Study of the Operational Safety of a Vascular Interventional Surgical Robotic System

    Directory of Open Access Journals (Sweden)

    Jian Guo

    2018-03-01

    Full Text Available This paper proposes an operation safety early warning system based on LabView (2014, National Instruments Corporation, Austin, TX, USA for vascular interventional surgery (VIS robotic system. The system not only provides intuitive visual feedback information for the surgeon, but also has a safety early warning function. It is well known that blood vessels differ in their ability to withstand stress in different age groups, therefore, the operation safety early warning system based on LabView has a vascular safety threshold function that changes in real-time, which can be oriented to different age groups of patients and a broader applicable scope. In addition, the tracing performance of the slave manipulator to the master manipulator is also an important index for operation safety. Therefore, we also transformed the slave manipulator and integrated the displacement error compensation algorithm in order to improve the tracking ability of the slave manipulator to the master manipulator and reduce master–slave tracking errors. We performed experiments “in vitro” to validate the proposed system. According to previous studies, 0.12 N is the maximum force when the blood vessel wall has been penetrated. Experimental results showed that the proposed operation safety early warning system based on LabView combined with operating force feedback can effectively avoid excessive collisions between the surgical catheter and vessel wall to avoid vascular puncture. The force feedback error of the proposed system is maintained between ±20 mN, which is within the allowable safety range and meets our design requirements. Therefore, the proposed system can ensure the safety of surgery.

  16. Investigating perioperative heart migration during robot-assisted coronary artery bypass grafting interventions.

    Science.gov (United States)

    Linte, Cristian A; Cho, Daniel S; Wedlake, Chris; Moore, John; Chen, Elvis; Bainbridge, Daniel; Patel, Rajni; Peters, Terry; Kiaii, Bob B

    2011-09-01

    : For robot-assisted coronary artery bypass graft interventions, surgeons typically use a preoperative thoracic computed tomography scan of the patient to plan the procedure. However, the cardiac anatomy is prone to changes induced perioperatively in the effort to access the heart and surgical targets, which, in turn, may invalidate the initial plan. This article presents a method to estimate the perioperative heart migration, information which can be further exploited to refine the preoperative surgical plan. : Tracked transesophageal ultrasound images of four patients' hearts were acquired at each stage in the procedure: before lung deflation, after lung deflation, and after both lung deflation and CO2 thoracic insufflation. Anatomic features of interest-the mitral and aortic valves-were identified from each dataset, and their movement between the different procedure stages was recorded and used to estimate the global heart displacement. Moreover, the local morphology of the features of interest was investigated to provide insight on the extent of the deformation the heart has undergone during the workflow. : The study suggested that the heart does undergo substantial displacement-on the order of 10 to 15 mm in each direction (axial, coronal, and sagittal) after lung deflation and CO2 thoracic insufflation. However, no significant differences (P > 0.1) were observed in the morphologic characteristics of the features of interest across the multiple workflow stages, suggesting that local deformations occur at a much smaller scale compared with the global migration. : The quantification of the perioperatively induced changes is critical to track the displacement of the heart and surgical targets. The recorded migration patterns should not be ignored but rather be used to update the surgical plan to better suit the intraoperative environment.

  17. Human-Like Behavior of Robot Arms: General Considerations and the Handwriting Task-Part I: Mathematical Description of Human-Like Motion: Distributed Positioning and Virtual Fatigue

    NARCIS (Netherlands)

    Potkonjak, V.; Tzafestas, S.; Kostic, D.; Djordjevic, G.

    2001-01-01

    This two-part paper is concerned with the analysis and achievement of human-like behavior by robot arms (manipulators). The analysis involves three issues: (i) the resolution of the inverse kinematics problem of redundant robots, (ii) the separation of the end-effector's motion into two components,

  18. The technical development of steerable catheter robot in performing interventional vascular surgery

    International Nuclear Information System (INIS)

    He Zhixiu; Qian Wei; Song Chengli

    2011-01-01

    Minimally invasive surgery is one of the primary means for the treatment of vascular diseases. The catheter is one of the main operating tools. As the vascular system is quite complicated and tiny, it is usually very difficult for the operator to accurately and bare-handily accomplish the whole intravascular procedure. Therefore, with the rapid development of minimally invasive surgeries the practical study related to the clinical employment of steerable catheter robot has attracted the researchers' attention. This paper aims to describe the emergence and development history of steerable catheter robot and also to introduce the main achievements as well as the up-to-date progress in the researches relevant to steerable catheter robot that the have been obtained by research workers all over the world so far. The prospects for the future development of steerable catheter robot are briefly discussed. (authors)

  19. The immediate intervention effects of robotic training in patients after anterior cruciate ligament reconstruction

    OpenAIRE

    Hu, Chunying; Huang, Qiuchen; Yu, Lili; Ye, Miao

    2016-01-01

    [Purpose] The purpose of this study was to examine the immediate effects of robot-assisted therapy on functional activity level after anterior cruciate ligament reconstruction. [Subjects and Methods] Participants included 10 patients (8 males and 2 females) following anterior cruciate ligament reconstruction. The subjects participated in robot-assisted therapy and treadmill exercise on different days. The Timed Up-and-Go test, Functional Reach Test, surface electromyography of the vastus late...

  20. Probabilistic scan mode of a robot manipulator workspace using EEG signals. Part II

    International Nuclear Information System (INIS)

    Auat Cheein, Fernando A; Di Sciascio, Fernando; Freire Bastos, Teodiano; Carelli, Ricardo

    2007-01-01

    In this paper a probabilistic-based workspace scan mode of a robot manipulator is presented. The workspace is divided into cells. Each cell has its own probability value associated with it. Once the robot reaches a cell, its probability value is updated. The updating process is governed by a recursive Bayes algorithm. A performance comparison between a sequential scan mode and the one proposed here is made. Mathematical derivations and experimental results are also shown in this paper

  1. Robotic intelligence kernel

    Science.gov (United States)

    Bruemmer, David J [Idaho Falls, ID

    2009-11-17

    A robot platform includes perceptors, locomotors, and a system controller. The system controller executes a robot intelligence kernel (RIK) that includes a multi-level architecture and a dynamic autonomy structure. The multi-level architecture includes a robot behavior level for defining robot behaviors, that incorporate robot attributes and a cognitive level for defining conduct modules that blend an adaptive interaction between predefined decision functions and the robot behaviors. The dynamic autonomy structure is configured for modifying a transaction capacity between an operator intervention and a robot initiative and may include multiple levels with at least a teleoperation mode configured to maximize the operator intervention and minimize the robot initiative and an autonomous mode configured to minimize the operator intervention and maximize the robot initiative. Within the RIK at least the cognitive level includes the dynamic autonomy structure.

  2. Operation and force analysis of the guide wire in a minimally invasive vascular interventional surgery robot system

    Science.gov (United States)

    Yang, Xue; Wang, Hongbo; Sun, Li; Yu, Hongnian

    2015-03-01

    To develop a robot system for minimally invasive surgery is significant, however the existing minimally invasive surgery robots are not applicable in practical operations, due to their limited functioning and weaker perception. A novel wire feeder is proposed for minimally invasive vascular interventional surgery. It is used for assisting surgeons in delivering a guide wire, balloon and stenting into a specific lesion location. By contrasting those existing wire feeders, the motion methods for delivering and rotating the guide wire in blood vessel are described, and their mechanical realization is presented. A new resistant force detecting method is given in details. The change of the resistance force can help the operator feel the block or embolism existing in front of the guide wire. The driving torque for rotating the guide wire is developed at different positions. Using the CT reconstruction image and extracted vessel paths, the path equation of the blood vessel is obtained. Combining the shapes of the guide wire outside the blood vessel, the whole bending equation of the guide wire is obtained. That is a risk criterion in the delivering process. This process can make operations safer and man-machine interaction more reliable. A novel surgery robot for feeding guide wire is designed, and a risk criterion for the system is given.

  3. EFSUMB Guidelines on Interventional Ultrasound (INVUS), Part III - Abdominal Treatment Procedures (Long Version)

    DEFF Research Database (Denmark)

    Dietrich, Christoph F; Lorentzen, T.; Appelbaum, L.

    2016-01-01

    The third part of the European Federation of Societies for Ultrasound in Medicine and Biology (EFSUMB) Guidelines on Interventional Ultrasound (INVUS) assesses the evidence for ultrasound-guided and assisted interventions in abdominal treatment procedures. Recommendations for clinical practice ar...

  4. EFSUMB Guidelines on Interventional Ultrasound (INVUS), Part III - Abdominal Treatment Procedures (Short Version)

    DEFF Research Database (Denmark)

    Dietrich, Christoph F; Lorentzen, T.; Appelbaum, L.

    2016-01-01

    The third part of the European Federation of Societies for Ultrasound in Medicine and Biology (EFSUMB) Guidelines on Interventional Ultrasound assesses the evidence for ultrasound-guided and assisted interventions in abdominal treatment procedures. Recommendations for clinical practice are presen...

  5. Project Tasks in Robotics

    DEFF Research Database (Denmark)

    Sørensen, Torben; Hansen, Poul Erik

    1998-01-01

    Description of the compulsary project tasks to be carried out as a part of DTU course 72238 Robotics......Description of the compulsary project tasks to be carried out as a part of DTU course 72238 Robotics...

  6. So Long, Robot Reader! A Superhero Intervention Plan for Improving Fluency

    Science.gov (United States)

    Marcell, Barclay; Ferraro, Christine

    2013-01-01

    This article presents an engaging means for turning disfluent readers into prosody superstars. Each week students align with Poetry Power Man and his superhero friends to battle the evil Robot Reader and his sidekicks. The Fluency Foursome helps students adhere to the multidimensional aspects of fluency where expression and comprehension are…

  7. Interventions for Stigma Reduction – Part 2: Practical Applications

    Directory of Open Access Journals (Sweden)

    Ajit Dalal

    2012-02-01

    Full Text Available This paper reports the endeavours of the Working Group assigned to develop guidelines for interventions to reduce stigma. The group was comprised of academics and experienced field personnel, all of whom had either investigated stigma, implemented actions to address stigma, and/or had experienced stigma. The group’s mandate was to develop an intervention to reduce the stigma of leprosy, but while accepting that there are commonalities relating to stigma that cut across different health conditions, it was hoped that a generic intervention might be developed. This goal proved to be unattainable in the time given: condition-specific peculiarities and the diversity of cultural contexts presented significant challenges. The group agreed, however, that a considerable body of theory and expert opinion does exist, and that general strategies might be developed from this. The Working Group discussed a systematic review of such material. It also discussed other material that was considered to be important but had not met the criteria for the systematic review. One conclusion of the group’s deliberations was that a “Stigma Intervention Matrix” could be a useful guide for cross-checking the development of situation-specific stigma interventions. The Stigma Intervention Matrix is presented in this paper.DOI: 10.5463/dcid.v22i3.72

  8. Robotic seeding

    DEFF Research Database (Denmark)

    Pedersen, Søren Marcus; Fountas, Spyros; Sørensen, Claus Aage Grøn

    2017-01-01

    Agricultural robotics has received attention for approximately 20 years, but today there are only a few examples of the application of robots in agricultural practice. The lack of uptake may be (at least partly) because in many cases there is either no compelling economic benefit......, or there is a benefit but it is not recognized. The aim of this chapter is to quantify the economic benefits from the application of agricultural robots under a specific condition where such a benefit is assumed to exist, namely the case of early seeding and re-seeding in sugar beet. With some predefined assumptions...... with regard to speed, capacity and seed mapping, we found that among these two technical systems both early seeding with a small robot and re-seeding using a robot for a smaller part of the field appear to be financially viable solutions in sugar beet production....

  9. Designing the optimal robotic milking barn, Part 1: Quantifying facility usage

    NARCIS (Netherlands)

    Halachmi, I.; Metz, J.H.M.; Maltz, E.; Dijkhuizen, A.A.; Speelman, L.

    2000-01-01

    The aim of this paper is to explore the stochastic nature of the usage of facilities in a robotic milking barn, independent of the barn layout. It presents experimental data obtained by monitoring 10 dairy cows over a period of 18 days. To minimize restrictions to the access of cows to the

  10. Storytelling intervention for patients with cancer: part 2--pilot testing.

    Science.gov (United States)

    Crogan, Neva L; Evans, Bronwynne C; Bendel, Robert

    2008-03-01

    To evaluate symptom reports and the impact of a nurse-led storytelling intervention in a supportive group setting on mood, stress level, coping with stress, pain, self-efficacy, and satisfaction with life in patients with cancer. Descriptive pilot project using a pretest/post-test control group. Local regional medical center in the Pacific Northwest region of the United States. Convenience sample of 10 patients with various cancer diagnoses; 7 completed the intervention. Participants were randomly assigned to a storytelling or control group. Using a tool kit generated for this project, a nurse facilitator guided storytelling group participants in 12 1.5-hour sessions. Six instruments, symptom assessments, and a retrospective physician chart review were completed for each group. Data were analyzed using repeated measures analysis of variance. Mood, stress, coping, pain, self-efficacy, and satisfaction with life. Comparison of changes in group mean scores revealed a significant decrease in anxiety in the storytelling group despite disease progression. Documentation of psychosocial symptomatology by physicians is limited; however, nursing assessments were useful in determining psychosocial status before and after the intervention. Results can be viewed only in context of a feasibility study and are not generalizable because of a limited sample size. A trained oncology nurse was able to use the storytelling intervention. Initial results are promising and warrant further study. After additional testing, the intervention could be used to enhance storytelling groups for patients with cancer or for individuals who are uncomfortable in or do not have access to storytelling groups.

  11. Predicting the long-term effects of human-robot interaction: a reflection on responsibility in medical robotics.

    Science.gov (United States)

    Datteri, Edoardo

    2013-03-01

    This article addresses prospective and retrospective responsibility issues connected with medical robotics. It will be suggested that extant conceptual and legal frameworks are sufficient to address and properly settle most retrospective responsibility problems arising in connection with injuries caused by robot behaviours (which will be exemplified here by reference to harms occurred in surgical interventions supported by the Da Vinci robot, reported in the scientific literature and in the press). In addition, it will be pointed out that many prospective responsibility issues connected with medical robotics are nothing but well-known robotics engineering problems in disguise, which are routinely addressed by roboticists as part of their research and development activities: for this reason they do not raise particularly novel ethical issues. In contrast with this, it will be pointed out that novel and challenging prospective responsibility issues may emerge in connection with harmful events caused by normal robot behaviours. This point will be illustrated here in connection with the rehabilitation robot Lokomat.

  12. Healthy lifestyle interventions in general practice: Part 1: An ...

    African Journals Online (AJOL)

    Poor lifestyle choices including physical inactivity, adverse nutrition and tobacco use are strongly associated with heart disease, diabetes, respiratory disease and cancer. These four diseases are responsible for over 50% of mortality worldwide. Yet lifestyle intervention is underemphasised in the undergraduate training of ...

  13. EFSUMB Guidelines on Interventional Ultrasound (INVUS), Part v

    DEFF Research Database (Denmark)

    Fusaroli, P; Jenssen, C.; Hocke, Martine

    2016-01-01

    The fifth section of the Guidelines on Interventional Ultrasound (INVUS) of the European Federation of Societies for Ultrasound in Medicine and Biology (EFSUMB) assesses the evidence for all the categories of endoscopic ultrasound-guided treatment reported to date. Celiac plexus neurolysis and bl...

  14. High-Field MRI-Compatible Needle Placement Robot for Prostate Interventions

    OpenAIRE

    SU, Hao; CAMILO, Alex; COLE, Gregory A.; HATA, Nobuhiko; TEMPANY, Clare M.; FISCHER, Gregory S.

    2011-01-01

    This paper presents the design of a magnetic resonance imaging (MRI) compatible needle placement system actuated by piezoelectric actuators for prostate brachytherapy and biopsy. An MRI-compatible modular 3 degree-of-freedom (DOF) needle driver module coupled with a 3-DOF x-y-z stage is proposed as a slave robot to precisely deliver radioactive brachytherapy seeds under interactive MRI guidance. The needle driver module provides for needle cannula rotation, needle insertion and cannula retrac...

  15. Integrating socially assistive robotics into mental healthcare interventions: applications and recommendations for expanded use.

    Science.gov (United States)

    Rabbitt, Sarah M; Kazdin, Alan E; Scassellati, Brian

    2015-02-01

    As a field, mental healthcare is faced with major challenges as it attempts to close the huge gap between those who need services and those who receive services. In recent decades, technological advances have provided exciting new resources in this battle. Socially assistive robotics (SAR) is a particularly promising area that has expanded into several exciting mental healthcare applications. Indeed, a growing literature highlights the variety of clinically relevant functions that these robots can serve, from companion to therapeutic play partner. This paper reviews the ways that SAR have already been used in mental health service and research and discusses ways that these applications can be expanded. We also outline the challenges and limitations associated with further integrating SAR into mental healthcare. SAR is not proposed as a replacement for specially trained and knowledgeable professionals nor is it seen as a panacea for all mental healthcare needs. Instead, robots can serve as clinical tools and assistants in a wide range of settings. Given the dramatic growth in this area, now is a critical moment for individuals in the mental healthcare community to become engaged in this research and steer it toward our field's most pressing clinical needs. Copyright © 2014. Published by Elsevier Ltd.

  16. Integrated navigation and control software system for MRI-guided robotic prostate interventions.

    Science.gov (United States)

    Tokuda, Junichi; Fischer, Gregory S; DiMaio, Simon P; Gobbi, David G; Csoma, Csaba; Mewes, Philip W; Fichtinger, Gabor; Tempany, Clare M; Hata, Nobuhiko

    2010-01-01

    A software system to provide intuitive navigation for MRI-guided robotic transperineal prostate therapy is presented. In the system, the robot control unit, the MRI scanner, and the open-source navigation software are connected together via Ethernet to exchange commands, coordinates, and images using an open network communication protocol, OpenIGTLink. The system has six states called "workphases" that provide the necessary synchronization of all components during each stage of the clinical workflow, and the user interface guides the operator linearly through these workphases. On top of this framework, the software provides the following features for needle guidance: interactive target planning; 3D image visualization with current needle position; treatment monitoring through real-time MR images of needle trajectories in the prostate. These features are supported by calibration of robot and image coordinates by fiducial-based registration. Performance tests show that the registration error of the system was 2.6mm within the prostate volume. Registered real-time 2D images were displayed 1.97 s after the image location is specified. Copyright 2009 Elsevier Ltd. All rights reserved.

  17. Integrated navigation and control software system for MRI-guided robotic prostate interventions

    Science.gov (United States)

    Tokuda, Junichi; Fischer, Gregory S.; DiMaio, Simon P.; Gobbi, David G.; Csoma, Csaba; Mewes, Philip W.; Fichtinger, Gabor; Tempany, Clare M.; Hata, Nobuhiko

    2010-01-01

    A software system to provide intuitive navigation for MRI-guided robotic transperineal prostate therapy is presented. In the system, the robot control unit, the MRI scanner, and the open-source navigation software are connected together via Ethernet to exchange commands, coordinates, and images using an open network communication protocol, OpenIGTLink. The system has six states called “workphases” that provide the necessary synchronization of all components during each stage of the clinical workflow, and the user interface guides the operator linearly through these workphases. On top of this framework, the software provides the following features for needle guidance: interactive target planning; 3D image visualization with current needle position; treatment monitoring through real-time MR images of needle trajectories in the prostate. These features are supported by calibration of robot and image coordinates by fiducial-based registration. Performance tests show that the registration error of the system was 2.6 mm within the prostate volume. Registered real-time 2D images were displayed 1.97 s after the image location is specified. PMID:19699057

  18. A MR-conditional High-torque Pneumatic Stepper Motor for MRI-guided and Robot-assisted Intervention

    Science.gov (United States)

    Chen, Yue; Kwok, Ka-Wai; Tse, Zion Tsz Ho

    2015-01-01

    Magnetic Resonance Imaging allows for visualizing detailed pathological and morphological changes of soft tissue. This increasingly attracts attention on MRI-guided intervention; hence, MR-conditional actuations have been widely investigated for development of image-guided and robot-assisted surgical devices under the MRI. This paper presents a simple design of MR-conditional stepper motor which can provide precise and high-torque actuation without adversely affecting the MR image quality. This stepper motor consists of two MR-conditional pneumatic cylinders and the corresponding supporting structures. Alternating the pressurized air can drive the motor to rotate each step in 3.6° with the motor coupled to a planetary gearbox. Experimental studies were conducted to validate its dynamics performance. Maximum 800mNm output torque can be achieved. The motor accuracy independently varied by two factors: motor operating speed and step size, was also investigated. The motor was tested within a Siemens 3T MRI scanner. The image artifact and the signal-to-noise ratio (SNR) were evaluated in order to study its MRI compliancy. The results show that the presented pneumatic stepper motor generated 2.35% SNR reduction in MR images and no observable artifact was presented besides the motor body itself. The proposed motor test also demonstrates a standard to evaluate the motor capability for later incorporation with motorized devices used in robot-assisted surgery under MRI. PMID:24957635

  19. Improving collaborative play between children with autism spectrum disorders and their siblings : the effectiveness of a robot-mediated intervention based on lego (R) therapy

    NARCIS (Netherlands)

    Huskens, Bibi; Palmen, Annemiek; Van der Werff, Marije; Lourens, Tino; Barakova, Emilia

    2015-01-01

    The aim of the study was to investigate the effectiveness of a brief robot-mediated intervention based on Lego(A (R)) therapy on improving collaborative behaviors (i.e., interaction initiations, responses, and play together) between children with ASD and their siblings during play sessions, in a

  20. Improving Collaborative Play between Children with Autism Spectrum Disorders and Their Siblings: The Effectiveness of a Robot-Mediated Intervention Based on Lego® Therapy

    Science.gov (United States)

    Huskens, Bibi; Palmen, Annemiek; Van der Werff, Marije; Lourens, Tino; Barakova, Emilia

    2015-01-01

    The aim of the study was to investigate the effectiveness of a brief robot-mediated intervention based on Lego® therapy on improving collaborative behaviors (i.e., interaction initiations, responses, and play together) between children with ASD and their siblings during play sessions, in a therapeutic setting. A concurrent multiple baseline design…

  1. Design and Kinematic Analysis of a New End-Effector for a Robotic Needle Insertion-Type Intervention System

    Directory of Open Access Journals (Sweden)

    Youngjin Moon

    2014-12-01

    Full Text Available This paper presents a new end-effector as a key component for a robotic needle insertion-type intervention system and its kinematic analysis. The mechanism is designed as a spherical mechanism with a revolute joint and a curved sliding joint, and its links always move on the surface of a sphere. The remote centre of motion (RCM of the designed mechanism is placed below the base of the mechanism to avoid contact with the patient's body, unlike the conventional end-effectors developed for needle insertion. For the proposed mechanism, the forward kinematics are solved in terms of input joint parameters and then the reverse kinematics are solved by using the cross-product relationship between each joint vector and a vector mutually perpendicular to the vectors. The kinematic solutions are confirmed by numerical examples.

  2. Robot arm based flat panel CT-guided electromagnetic tracked spine interventions: phantom and animal model experiments

    International Nuclear Information System (INIS)

    Penzkofer, Tobias; Isfort, Peter; Bruners, Philipp; Mahnken, Andreas H.; Wiemann, Christian; Guenther, Rolf W.; Kyriakou, Yiannis; Kalender, Willi A.; Schmitz-Rode, Thomas

    2010-01-01

    To evaluate accuracy and procedure times of electromagnetic tracking (EMT) in a robotic arm mounted flat panel setting using phantom and animal cadaveric models. A robotic arm mounted flat panel (RMFP) was used in combination with EMT to perform anthropomorphic phantom (n = 90) and ex vivo pig based punctures (n = 120) of lumbar facet joints (FJ, n = 120) and intervertebral discs (IVD, n = 90). Procedure accuracies and times were assessed and evaluated. FJ punctures were carried out with a spatial accuracy of 0.8 ± 0.9 mm (phantom) and 0.6 ± 0.8 mm (ex vivo) respectively. While IVD punctures showed puncture deviations of 0.6 ± 1.2 mm (phantom) and 0.5 ± 0.6 mm (ex vivo), direct and angulated phantom based punctures had accuracies of 0.8 ± 0.9 mm and 1.0 ± 1.3 mm. Planning took longer for ex vivo IVD punctures compared to phantom model interventions (39.3 ± 17.3 s vs. 20.8 ± 5.0 s, p = 0.001) and for angulated vs. direct phantom FJ punctures (19.7 ± 5.1 s vs. 28.6 ± 7.8 s, p < 0.001). Puncture times were longer for ex vivo procedures when compared to phantom model procedures in both FJ (37.9 ± 9.0 s vs. 23.6 ± 7.2 s, p = 0.001) and IVD punctures (43.9 ± 16.1 s vs. 31.1 ± 6.4 s, p = 0.026). The combination of RMFP with EMT provides an accurate method of navigation for spinal interventions such as facet joint punctures and intervertebral disc punctures. (orig.)

  3. Robot arm based flat panel CT-guided electromagnetic tracked spine interventions: phantom and animal model experiments

    Energy Technology Data Exchange (ETDEWEB)

    Penzkofer, Tobias; Isfort, Peter; Bruners, Philipp; Mahnken, Andreas H. [RWTH Aachen University, Applied Medical Engineering, Helmholtz-Institute Aachen, Aachen (Germany); RWTH Aachen University, Department of Diagnostic Radiology, Aachen University Hospital, Aachen (Germany); Wiemann, Christian; Guenther, Rolf W. [RWTH Aachen University, Department of Diagnostic Radiology, Aachen University Hospital, Aachen (Germany); Kyriakou, Yiannis; Kalender, Willi A. [Friedrich-Alexander University of Erlangen-Nuremberg, Institute for Medical Physics, Erlangen (Germany); Schmitz-Rode, Thomas [RWTH Aachen University, Applied Medical Engineering, Helmholtz-Institute Aachen, Aachen (Germany)

    2010-11-15

    To evaluate accuracy and procedure times of electromagnetic tracking (EMT) in a robotic arm mounted flat panel setting using phantom and animal cadaveric models. A robotic arm mounted flat panel (RMFP) was used in combination with EMT to perform anthropomorphic phantom (n = 90) and ex vivo pig based punctures (n = 120) of lumbar facet joints (FJ, n = 120) and intervertebral discs (IVD, n = 90). Procedure accuracies and times were assessed and evaluated. FJ punctures were carried out with a spatial accuracy of 0.8 {+-} 0.9 mm (phantom) and 0.6 {+-} 0.8 mm (ex vivo) respectively. While IVD punctures showed puncture deviations of 0.6 {+-} 1.2 mm (phantom) and 0.5 {+-} 0.6 mm (ex vivo), direct and angulated phantom based punctures had accuracies of 0.8 {+-} 0.9 mm and 1.0 {+-} 1.3 mm. Planning took longer for ex vivo IVD punctures compared to phantom model interventions (39.3 {+-} 17.3 s vs. 20.8 {+-} 5.0 s, p = 0.001) and for angulated vs. direct phantom FJ punctures (19.7 {+-} 5.1 s vs. 28.6 {+-} 7.8 s, p < 0.001). Puncture times were longer for ex vivo procedures when compared to phantom model procedures in both FJ (37.9 {+-} 9.0 s vs. 23.6 {+-} 7.2 s, p = 0.001) and IVD punctures (43.9 {+-} 16.1 s vs. 31.1 {+-} 6.4 s, p = 0.026). The combination of RMFP with EMT provides an accurate method of navigation for spinal interventions such as facet joint punctures and intervertebral disc punctures. (orig.)

  4. EFSUMB Guidelines on Interventional Ultrasound (INVUS), Part v - EUS-Guided Therapeutic Interventions (short version)

    DEFF Research Database (Denmark)

    Fusaroli, P; Jenssen, C.; Hocke, Martine

    2016-01-01

    and block, vascular intervention, drainage of fluid collections, drainage of biliary and pancreatic ducts, and experimental tumor ablation techniques are discussed. For each topic, all current evidence has been extensively analyzed and summarized into major recommendations for reader consultation (short...

  5. Demonstration of the Safety and Feasibility of Robotically Assisted Percutaneous Coronary Intervention in Complex Coronary Lesions: Results of the CORA-PCI Study (Complex Robotically Assisted Percutaneous Coronary Intervention).

    Science.gov (United States)

    Mahmud, Ehtisham; Naghi, Jesse; Ang, Lawrence; Harrison, Jonathan; Behnamfar, Omid; Pourdjabbar, Ali; Reeves, Ryan; Patel, Mitul

    2017-07-10

    The aims of this study were to evaluate the feasibility and technical success of robotically assisted percutaneous coronary intervention (R-PCI) for the treatment of coronary artery disease (CAD) in clinical practice, especially in complex lesions, and to determine the safety and clinical success of R-PCI compared with manual percutaneous coronary intervention (M-PCI). R-PCI is safe and feasible for simple coronary lesions. The utility of R-PCI for complex coronary lesions is unknown. All consecutive PCI procedures performed robotically (study group) or manually (control group) over 18 months were included. R-PCI technical success, defined as the completion of the procedure robotically or with partial manual assistance and without a major adverse cardiovascular event, was determined. Procedures ineligible for R-PCI (i.e., atherectomy, planned 2-stent strategy for bifurcation lesion, chronic total occlusion requiring hybrid approach) were excluded for analysis from the M-PCI group. Clinical success, defined as completion of the PCI procedure without a major adverse cardiovascular event, procedure time, stent use, and fluoroscopy time were compared between groups. A total of 315 patients (mean age 67.7 ± 11.8 years; 78% men) underwent 334 PCI procedures (108 R-PCIs, 157 lesions, 78.3% type B2/C; 226 M-PCIs, 336 lesions, 68.8% type B2/C). Technical success with R-PCI was 91.7% (rate of manual assistance 11.1%, rate of manual conversion 7.4%, rate of major adverse cardiovascular events 0.93%). Clinical success (99.1% with R-PCI vs. 99.1% with M-PCI; p = 1.00), stent use (stents per procedure 1.59 ± 0.79 with R-PCI vs. 1.54 ± 0.75 with M-PCI; p = 0.73), and fluoroscopy time (18.2 ± 10.4 min with R-PCI vs. 19.2 ± 11.4 min with M-PCI; p = 0.39) were similar between the groups, although procedure time was longer in the R-PCI group (44:30 ± 26:04 min:s vs. 36:34 ± 23:03 min:s; p = 0.002). Propensity-matched analysis confirmed that procedure time was longer

  6. Parents' Judgments of the Acceptability and Importance of Socially Interactive Robots for Intervening with Young Children with Disabilities. Social Robots Research Reports, Number 1

    Science.gov (United States)

    Dunst, Carl J.; Trivette, Carol M.; Prior, Jeremy; Hamby, Deborah W.; Embler, Davon

    2013-01-01

    A number of different types of socially interactive robots are being used as part of interventions with young children with disabilities to promote their joint attention and language skills. Parents' judgments of two dimensions (acceptance and importance) of the social validity of four different social robots were the focus of the study described…

  7. Mentalizing Family Violence Part 2: Techniques and Interventions.

    Science.gov (United States)

    Asen, Eia; Fonagy, Peter

    2017-03-01

    This is the second of two companion papers that provide an overview of mentalization-based concepts and techniques when working with the seeming "mindlessness" of intra-family violence. The focus of this paper is on general mentalization-oriented approaches and specific interventions that aim to (1) disrupt the non-mentalizing cycles that can generate intra-family violence and (2) encourage the emergence of patterns of family interactions that provide the foundation for non-violent alternatives. Various playful exercises and activities are described, including the taking of "mental state snapshots" and "selfies" in sessions and staging inverted role-plays, as well as using theatrical masks and creating body-mind maps and scans. These can make "chronic" relationship issues come alive in session and permit "here and now" experiences that generate a safe context for mentalizing to take place. At the core of the work is the continuous focus on integrating experience and reflection. Without acute awareness of the thoughts and feelings occurring in the sessions, mere reflection is not likely to enable change. By increasing mentalizing in the family system, family members' trusting attitudes grow, both within and outside the family. © 2017 Family Process Institute.

  8. High-Field MRI-Compatible Needle Placement Robot for Prostate Interventions

    Science.gov (United States)

    SU, Hao; CAMILO, Alex; COLE, Gregory A.; HATA, Nobuhiko; TEMPANY, Clare M.; FISCHER, Gregory S.

    2014-01-01

    This paper presents the design of a magnetic resonance imaging (MRI) compatible needle placement system actuated by piezoelectric actuators for prostate brachytherapy and biopsy. An MRI-compatible modular 3 degree-of-freedom (DOF) needle driver module coupled with a 3-DOF x-y-z stage is proposed as a slave robot to precisely deliver radioactive brachytherapy seeds under interactive MRI guidance. The needle driver module provides for needle cannula rotation, needle insertion and cannula retraction to enable the brachytherapy procedure with the preloaded needles. The device mimics the manual physician gesture by two point grasping (hub and base) and provides direct force measurement of needle insertion force by fiber optic force sensors. The fabricated prototype is presented and an experiment with phantom trials in 3T MRI is analyzed to demonstrate the system compatibility. PMID:21335868

  9. Design of a Biomimetic Skin for an Octopus-Inspired Robot - Part Ⅰ: Characterising Octopus Skin

    Institute of Scientific and Technical Information of China (English)

    Jinping Hou; Richard H. C. Bonser; George Jeronimidis

    2011-01-01

    Octopus skin samples were tested under quasi-static and scissor cutting conditions to measure the in-plane material properties and fracture toughness. Samples from all eight arms of one octopus were tested statically to investigate how properties vary from arm to arm. Another nine octopus skins were measured to study the influence of body mass on skin properties. Influence of specimen location on skin mechanical properties was also studied. Material properties of skin, i.e. the Young's modulus, ultimate stress, failure strain and fracture toughness have been plotted against the position of skin along the length of arm or body. Statistical studies were carried out to help analyzing experimental data obtained. Results of this work will be used as guidelines for the design and development of artificial skins for an octopus-inspired robot.

  10. Y-12 Plant remedial action Technology Logic Diagram: Volume 3, Technology evaluation data sheets: Part B, Characterization; robotics/automation

    International Nuclear Information System (INIS)

    1994-09-01

    The Y-12 Plant Remedial Action Technology Logic Diagram (TLD) was developed to provide a decision-support tool that relates environmental restoration (ER) problems at the Y-12 Plant to potential technologies that can remediate theses problems. The TLD identifies the research, development, demonstration, testing, and evaluation needed for sufficient development of these technologies to allow for technology transfer and application to remedial action (RA) activities. The TLD consists of three volumes. Volume 1 contains an overview of the TLD, an explanation of the program-specific responsibilities, a review of identified technologies, and the rankings of remedial technologies. Volume 2 contains the logic linkages among environmental management goals, environmental problems, and the various technologies that have the potential to solve these problems. Volume 3 contains the TLD data sheets. This report is Part B of Volume 3 and contains the Characterization and Robotics/Automation sections

  11. Reshaping of Gait Coordination by Robotic Intervention in Myelopathy Patients After Surgery

    Science.gov (United States)

    Puentes, Sandra; Kadone, Hideki; Kubota, Shigeki; Abe, Tetsuya; Shimizu, Yukiyo; Marushima, Aiki; Sankai, Yoshiyuki; Yamazaki, Masashi; Suzuki, Kenji

    2018-01-01

    The Ossification of the Posterior Longitudinal Ligament (OPLL) is an idiopathic degenerative spinal disease which may cause motor deficit. For patients presenting myelopathy or severe stenosis, surgical decompression is the treatment of choice; however, despite adequate decompression residual motor impairment is found in some cases. After surgery, there is no therapeutic approach available for this population. The Hybrid Assistive Limb® (HAL) robot suit is a unique powered exoskeleton designed to predict, support, and enhance the lower extremities performance of patients using their own bioelectric signals. This approach has been used for spinal cord injury and stroke patients where the walking performance improved. However, there is no available data about gait kinematics evaluation after HAL therapy. Here we analyze the effect of HAL therapy in OPLL patients in acute and chronic stages after decompression surgery. We found that HAL therapy improved the walking performance for both groups. Interestingly, kinematics evaluation by the analysis of the elevation angles of the thigh, shank, and foot by using a principal component analysis showed that planar covariation, plane orientation, and movement range evaluation improved for acute patients suggesting an improvement in gait coordination. Being the first study performing kinematics analysis after HAL therapy, our results suggest that HAL improved the gait coordination of acute patients by supporting the relearning process and therefore reshaping their gait pattern. PMID:29551960

  12. Robot arm based flat panel CT-guided electromagnetic tracked spine interventions: phantom and animal model experiments.

    Science.gov (United States)

    Penzkofer, Tobias; Isfort, Peter; Bruners, Philipp; Wiemann, Christian; Kyriakou, Yiannis; Kalender, Willi A; Günther, Rolf W; Schmitz-Rode, Thomas; Mahnken, Andreas H

    2010-11-01

    To evaluate accuracy and procedure times of electromagnetic tracking (EMT) in a robotic arm mounted flat panel setting using phantom and animal cadaveric models. A robotic arm mounted flat panel (RMFP) was used in combination with EMT to perform anthropomorphic phantom (n = 90) and ex vivo pig based punctures (n = 120) of lumbar facet joints (FJ, n = 120) and intervertebral discs (IVD, n = 90). Procedure accuracies and times were assessed and evaluated. FJ punctures were carried out with a spatial accuracy of 0.8 ± 0.9 mm (phantom) and 0.6 ± 0.8 mm (ex vivo) respectively. While IVD punctures showed puncture deviations of 0.6 ± 1.2 mm (phantom) and 0.5 ± 0.6 mm (ex vivo), direct and angulated phantom based punctures had accuracies of 0.8 ± 0.9 mm and 1.0 ± 1.3 mm. Planning took longer for ex vivo IVD punctures compared to phantom model interventions (39.3 ± 17.3 s vs. 20.8 ± 5.0 s, p = 0.001) and for angulated vs. direct phantom FJ punctures (19.7 ± 5.1 s vs. 28.6 ± 7.8 s, p < 0.001). Puncture times were longer for ex vivo procedures when compared to phantom model procedures in both FJ (37.9 ± 9.0 s vs. 23.6 ± 7.2 s, p = 0.001) and IVD punctures (43.9 ± 16.1 s vs. 31.1 ± 6.4 s, p = 0.026). The combination of RMFP with EMT provides an accurate method of navigation for spinal interventions such as facet joint punctures and intervertebral disc punctures.

  13. Exploratorium: Robots.

    Science.gov (United States)

    Brand, Judith, Ed.

    2002-01-01

    This issue of Exploratorium Magazine focuses on the topic robotics. It explains how to make a vibrating robotic bug and features articles on robots. Contents include: (1) "Where Robot Mice and Robot Men Run Round in Robot Towns" (Ray Bradbury); (2) "Robots at Work" (Jake Widman); (3) "Make a Vibrating Robotic Bug" (Modesto Tamez); (4) "The Robot…

  14. An overview of artificial intelligence and robotics. Volume 1: Artificial intelligence. Part B: Applications

    Science.gov (United States)

    Gevarter, W. B.

    1983-01-01

    Artificial Intelligence (AI) is an emerging technology that has recently attracted considerable attention. Many applications are now under development. This report, Part B of a three part report on AI, presents overviews of the key application areas: Expert Systems, Computer Vision, Natural Language Processing, Speech Interfaces, and Problem Solving and Planning. The basic approaches to such systems, the state-of-the-art, existing systems and future trends and expectations are covered.

  15. Combining psychological and engineering approaches to utilizing social robots with children with autism.

    Science.gov (United States)

    Dickstein-Fischer, Laurie; Fischer, Gregory S

    2014-01-01

    It is estimated that Autism Spectrum Disorder (ASD) affects 1 in 68 children. Early identification of an ASD is exceedingly important to the introduction of an intervention. We are developing a robot-assisted approach that will serve as an improved diagnostic and early intervention tool for children with autism. The robot, named PABI® (Penguin for Autism Behavioral Interventions), is a compact humanoid robot taking on an expressive cartoon-like embodiment. The robot is affordable, durable, and portable so that it can be used in various settings including schools, clinics, and the home. Thus enabling significantly enhanced and more readily available diagnosis and continuation of care. Through facial expressions, body motion, verbal cues, stereo vision-based tracking, and a tablet computer, the robot is capable of interacting meaningfully with an autistic child. Initial implementations of the robot, as part of a comprehensive treatment model (CTM), include Applied Behavioral Analysis (ABA) therapy where the child interacts with a tablet computer wirelessly interfaced with the robot. At the same time, the robot makes meaningful expressions and utterances and uses stereo cameras in eyes to track the child, maintain eye contact, and collect data such as affect and gaze direction for charting of progress. In this paper we present the clinical justification, anticipated usage with corresponding requirements, prototype development of the robotic system, and demonstration of a sample application for robot-assisted ABA therapy.

  16. A Research Synthesis of Therapeutic Interventions for Whiplash-Associated Disorder (WAD: Part 3 – Interventions for Subacute WAD

    Directory of Open Access Journals (Sweden)

    Robert W Teasell

    2010-01-01

    Full Text Available Whiplash-associated disorder (WAD represents a significant public health problem, resulting in substantial social and economic costs throughout the industrialized world. While many treatments have been advocated for patients with WAD, scientific evidence supporting their effectiveness is often lacking. A systematic review was conducted to evaluate the strength of evidence associated with various WAD therapies. Multiple databases (including Web of Science, EMBASE and PubMed were searched to identify all studies published from January 1980 through March 2009 that evaluated the effectiveness of any clearly defined treatment for acute (less than two weeks, subacute (two to 12 weeks or chronic (longer than 12 weeks WAD. The present article, the third in a five-part series, evaluates the evidence for interventions initiated during the subacute phase of WAD. Thirteen studies that met the inclusion criteria were identified, six of which were randomized controlled trials with ‘good’ overall methodology (median Physiotherapy Evidence Database score of 6. Although some evidence was identified to support the use of interdisciplinary interventions and chiropractic manipulation, the evidence was not strong for any of the evaluated treatments. There is a clear need for further research to evaluate interventions aimed at treating patients with subacute WAD because there are currently no interventions satisfactorily supported by the research literature.

  17. Medical robotics

    CERN Document Server

    Troccaz, Jocelyne

    2013-01-01

    In this book, we present medical robotics, its evolution over the last 30 years in terms of architecture, design and control, and the main scientific and clinical contributions to the field. For more than two decades, robots have been part of hospitals and have progressively become a common tool for the clinician. Because this domain has now reached a certain level of maturity it seems important and useful to provide a state of the scientific, technological and clinical achievements and still open issues. This book describes the short history of the domain, its specificity and constraints, and

  18. 75 FR 3746 - Ryan White HIV/AIDS Part C Early Intervention Services (EIS) Program

    Science.gov (United States)

    2010-01-22

    ... HIV/AIDS Part C Early Intervention Services (EIS) Program AGENCY: Health Resources and Services...: Critical funding for HIV/AIDS care and treatment to the target populations in Orange County, Orlando..., 2010). The Orange County Health Department is known Statewide as an exceptional site for HIV/AIDS care...

  19. 78 FR 18989 - Ryan White HIV/AIDS Program, Part C Early Intervention Services Grant Under the Ryan White HIV...

    Science.gov (United States)

    2013-03-28

    ... HIV/AIDS Program, Part C Early Intervention Services Grant Under the Ryan White HIV/AIDS Program.... ACTION: Notice of Ryan White HIV/AIDS Program Part C Early Intervention Services One-Time Noncompetitive... care services for persons living with HIV/AIDS, HRSA will provide a one-time noncompetitive Part C...

  20. 78 FR 10182 - Ryan White HIV/AIDS Program, Part C Early Intervention Services Grant Under the Ryan White HIV...

    Science.gov (United States)

    2013-02-13

    ... HIV/AIDS Program, Part C Early Intervention Services Grant Under the Ryan White HIV/AIDS Program.... ACTION: Notice of Ryan White HIV/AIDS Program (Part C) Early Intervention Services One-Time... primary care services for persons living with HIV/AIDS, HRSA will provide one-time noncompetitive Part C...

  1. Patient Evaluation and Preparation in Vascular and Interventional Radiology: What Every Interventional Radiologist Should Know (Part 2: Patient Preparation and Medications)

    Energy Technology Data Exchange (ETDEWEB)

    Taslakian, Bedros, E-mail: btaslakian@gmail.com [NYU Langone Medical Center, Department of Radiology (United States); Sebaaly, Mikhael Georges, E-mail: ms246@aub.edu.lb; Al-Kutoubi, Aghiad, E-mail: mk00@aub.edu.lb [American University of Beirut Medical Center, Department of Diagnostic Radiology (Lebanon)

    2016-04-15

    Performing an interventional procedure imposes a commitment on interventional radiologists to conduct the initial patient assessment, determine the best course of therapy, and provide long-term care. Patient care before and after an interventional procedure, identification, and management of early and delayed complications of various procedures are equal in importance to the procedure itself. In this second part, we complete the comprehensive, methodical review of pre-procedural care and patient preparation before vascular and interventional radiology procedures.

  2. Robot Actors, Robot Dramaturgies

    DEFF Research Database (Denmark)

    Jochum, Elizabeth

    This paper considers the use of tele-operated robots in live performance. Robots and performance have long been linked, from the working androids and automata staged in popular exhibitions during the nineteenth century and the robots featured at Cybernetic Serendipity (1968) and the World Expo...

  3. DETAILS OF OPERATIONS PERFORMED BY THE REMOTE CONTROL ROBOT (CONCEPT TO THE HORIZONTAL FUEL CHANNEL DURING DECOMMISSIONING PHASE OF NUCLEAR REACTOR CALANDRIA STRUCTURE. PART II: INSIDE OPERATIONS

    Directory of Open Access Journals (Sweden)

    Constantin POPESCU

    2017-05-01

    Full Text Available The authors contribution to this paper is to present a concept solution of a remote control robot (RCR used for decommissioning of the horizontal fuel channels pressure tube in the CANDU nuclear reactor. In this paper the authors highlight few details of geometry, operations, constraints by kinematics and dynamics of the robot movement inside of the reactor fuel channel. Inside operations performed has as the main steps of dismantling process the followings: unblock and extract the channel closure plug (from End Fitting - EF, unblock and extract the channel shield plug (from Lattice Tube - LT, cut the ends of the pressure tube, extract the pressure tube and cut it in small parts, sorting and storage extracted items in the safe robot container. All steps are performed in automatic mode. The remote control robot (RCR represents a safety system controlled by sensors and has the capability to analyze any error registered and decide next activities or abort the inside decommissioning procedure in case of any risk rise in order to ensure the environmental and workers protection.

  4. Going Green Robots

    Science.gov (United States)

    Nelson, Jacqueline M.

    2011-01-01

    In looking at the interesting shapes and sizes of old computer parts, creating robots quickly came to the author's mind. In this article, she describes how computer parts can be used creatively. Students will surely enjoy creating their very own robots while learning about the importance of recycling in the society. (Contains 1 online resource.)

  5. Robotic architectures

    CSIR Research Space (South Africa)

    Mtshali, M

    2010-01-01

    Full Text Available In the development of mobile robotic systems, a robotic architecture plays a crucial role in interconnecting all the sub-systems and controlling the system. The design of robotic architectures for mobile autonomous robots is a challenging...

  6. Risk Aversion and Public Reporting. Part 1: Observations From Cardiac Surgery and Interventional Cardiology.

    Science.gov (United States)

    Shahian, David M; Jacobs, Jeffrey P; Badhwar, Vinay; D'Agostino, Richard S; Bavaria, Joseph E; Prager, Richard L

    2017-12-01

    Risk aversion is a potential unintended consequence of health care public reporting. In Part 1 of this review, four possible consequences of this phenomenon are discussed, including the denial of interventions to some high-risk patients, stifling of innovation, appropriate avoidance of futile interventions, and better matching of high-risk patients to more capable providers. We also summarize relevant observational clinical reports and survey results from cardiovascular medicine and surgery, the two specialties from which almost all risk aversion observations have been derived. Although these demonstrate that risk aversion does occur, the empirical data are much more consistent and compelling for interventional cardiology than for cardiac surgery. Copyright © 2017 The Society of Thoracic Surgeons. Published by Elsevier Inc. All rights reserved.

  7. A creative arts intervention for children with diabetes. Part 2: evaluation.

    Science.gov (United States)

    Basso, Robert V J; Pelech, William James

    2008-12-01

    In Part 1 of this article (published in the October 2008 issue), we discussed the importance of using creative arts skits as an expressive technique for children with Type 1, or juvenile, diabetes. This creative arts intervention offers children the opportunity to decipher emotional difficulties through symbolic play in a secure atmosphere. Analysis of feelings following the skits encourages children to share concerns about their illnesses as well as self-concept issues. In Part 2, we use the case study method to demonstrate the benefits of creative arts skits for children with diabetes.

  8. Effects of a Socially Interactive Robot on the Conversational Turns between Parents and Their Young Children with Autism. Social Robots Research Reports, Number 6

    Science.gov (United States)

    Dunst, Carl J.; Hamby, Deborah W.; Trivette, Carol M.; Prior, Jeremy; Derryberry, Graham

    2013-01-01

    The effects of a socially interactive robot on the conversational turns between four young children with autism and their mothers were investigated as part of the intervention study described in this research report. The interventions with each child were conducted over 4 or 5 days in the children's homes where a practitioner facilitated…

  9. Robots and lattice automata

    CERN Document Server

    Adamatzky, Andrew

    2015-01-01

    The book gives a comprehensive overview of the state-of-the-art research and engineering in theory and application of Lattice Automata in design and control of autonomous Robots. Automata and robots share the same notional meaning. Automata (originated from the latinization of the Greek word “αυτόματον”) as self-operating autonomous machines invented from ancient years can be easily considered the first steps of robotic-like efforts. Automata are mathematical models of Robots and also they are integral parts of robotic control systems. A Lattice Automaton is a regular array or a collective of finite state machines, or automata. The Automata update their states by the same rules depending on states of their immediate neighbours. In the context of this book, Lattice Automata are used in developing modular reconfigurable robotic systems, path planning and map exploration for robots, as robot controllers, synchronisation of robot collectives, robot vision, parallel robotic actuators. All chapters are...

  10. 78 FR 10183 - Ryan White HIV/AIDS Program, Part C Early Intervention Services Grant Under the Ryan White HIV...

    Science.gov (United States)

    2013-02-13

    ... HIV/AIDS Program, Part C Early Intervention Services Grant Under the Ryan White HIV/AIDS Program.... ACTION: Notice of Ryan White HIV/AIDS Program Part C Early Intervention Services One-Time Noncompetitive... care services for persons living with HIV/AIDS, HRSA will provide one-time noncompetitive Ryan White...

  11. 78 FR 78976 - Ryan White HIV/AIDS Program Part C Early Intervention Services Grant Under the Ryan White HIV...

    Science.gov (United States)

    2013-12-27

    ... HIV/AIDS Program Part C Early Intervention Services Grant Under the Ryan White HIV/AIDS Program AGENCY...: Notice of Ryan White HIV/AIDS Program Part C Early Intervention Services One-Time Noncompetitive Award To... services for persons living with HIV/AIDS, HRSA will provide a one-time noncompetitive Ryan White HIV/AIDS...

  12. 78 FR 31568 - Ryan White HIV/AIDS Program, Part C Early Intervention Services Grant Under the Ryan White HIV...

    Science.gov (United States)

    2013-05-24

    ... HIV/AIDS Program, Part C Early Intervention Services Grant Under the Ryan White HIV/AIDS Program.... ACTION: Notice of Ryan White HIV/AIDS Program Part C Early Intervention Services One-Time Noncompetitive... care services for persons living with HIV/AIDS, HRSA will provide a one-time noncompetitive Ryan White...

  13. 32 CFR Appendix A to Part 57 - Procedures for the Provision of Early Intervention Services for Infants and Toddlers With...

    Science.gov (United States)

    2010-07-01

    ... developmental areas: (i) Cognitive development. (ii) Physical development, including vision and hearing. (iii... Intervention Services for Infants and Toddlers With Disabilities and Their Families A Appendix A to Part 57... Appendix A to Part 57—Procedures for the Provision of Early Intervention Services for Infants and Toddlers...

  14. Robot engineering

    International Nuclear Information System (INIS)

    Jung, Seul

    2006-02-01

    This book deals with robot engineering, giving descriptions of robot's history, current tendency of robot field, work and characteristic of industrial robot, essential merit and vector, application of matrix, analysis of basic vector, expression of Denavit-Hartenberg, robot kinematics such as forward kinematics, inverse kinematics, cases of MATLAB program, and motion kinematics, robot kinetics like moment of inertia, centrifugal force and coriolis power, and Euler-Lagrangian equation course plan, SIMULINK position control of robots.

  15. Robot engineering

    Energy Technology Data Exchange (ETDEWEB)

    Jung, Seul

    2006-02-15

    This book deals with robot engineering, giving descriptions of robot's history, current tendency of robot field, work and characteristic of industrial robot, essential merit and vector, application of matrix, analysis of basic vector, expression of Denavit-Hartenberg, robot kinematics such as forward kinematics, inverse kinematics, cases of MATLAB program, and motion kinematics, robot kinetics like moment of inertia, centrifugal force and coriolis power, and Euler-Lagrangian equation course plan, SIMULINK position control of robots.

  16. A Research Synthesis of Therapeutic Interventions for Whiplash-Associated Disorder (WAD: Part 4 – Noninvasive Interventions for Chronic WAD

    Directory of Open Access Journals (Sweden)

    Robert W Teasell

    2010-01-01

    Full Text Available Whiplash-associated disorder (WAD represents a significant public health problem, resulting in substantial social and economic costs throughout the industrialized world. While many treatments have been advocated for patients with WAD, scientific evidence supporting their effectiveness is often lacking. A systematic review was conducted to evaluate the strength of evidence for various WAD therapies. Multiple databases (including Web of Science, EMBASE and PubMed were searched to identify all studies published from January 1980 through March 2009 that evaluated the effectiveness of any clearly defined treatment for acute (less than two weeks, subacute (two to 12 weeks or chronic (longer than 12 weeks WAD. The present article, the fourth in a five-part series, evaluates the evidence for noninvasive interventions initiated during the chronic phase of WAD. Twenty-two studies that met the inclusion criteria were identified, 12 of which were randomized controlled trials with ‘good’ overall methodological quality (median Physiotherapy Evidence Database score of 6. For the treatment of chronic WAD, there is evidence to suggest that exercise programs are effective in relieving whiplash-related pain, at least over the short term. While the majority of a subset of nine studies supported the effectiveness of interdisciplinary interventions, the two randomized controlled trials provided conflicting results. Finally, there was limited evidence, consisting of one supportive case series each, that both manual joint manipulation and myofeedback training may provide some benefit. Based on the available research, exercise programs were the most effective noninvasive treatment for patients with chronic WAD, although many questions remain regarding the relative effectiveness of various exercise regimens.

  17. A Review of CAM for Procedural Pain in Infancy: Part II. Other Interventions

    Directory of Open Access Journals (Sweden)

    Jennie C. I. Tsao

    2008-01-01

    Full Text Available This article is the second in a two-part series reviewing the empirical evidence for complementary and alternative medicine (CAM approaches for the management of pain related to medical procedures in infants up to 6 weeks of age. Part I of this series investigated the effects of sucrose with or without non-nutritive sucking (NNS. The present article examines other CAM interventions for procedural pain including music-based interventions, olfactory stimulation, kangaroo care and swaddling. Computerized databases were searched for relevant studies including prior reviews and primary trials. Preliminary support was revealed for the analgesic effects of the CAM modalities reviewed. However, the overall quality of the evidence for these approaches remains relatively weak. Additional well-designed trials incorporating rigorous methodology are required. Such investigations will assist in the development of evidence-based guidelines on the use of CAM interventions either alone or in concert with conventional approaches to provide safe, reliable analgesia for infant procedural pain.

  18. Robot-laser system

    International Nuclear Information System (INIS)

    Akeel, H.A.

    1987-01-01

    A robot-laser system is described for providing a laser beam at a desired location, the system comprising: a laser beam source; a robot including a plurality of movable parts including a hollow robot arm having a central axis along which the laser source directs the laser beam; at least one mirror for reflecting the laser beam from the source to the desired location, the mirror being mounted within the robot arm to move therewith and relative thereto to about a transverse axis that extends angularly to the central axis of the robot arm; and an automatic programmable control system for automatically moving the mirror about the transverse axis relative to and in synchronization with movement of the robot arm to thereby direct the laser beam to the desired location as the arm is moved

  19. Neuro-robotics from brain machine interfaces to rehabilitation robotics

    CERN Document Server

    Artemiadis

    2014-01-01

    Neuro-robotics is one of the most multidisciplinary fields of the last decades, fusing information and knowledge from neuroscience, engineering and computer science. This book focuses on the results from the strategic alliance between Neuroscience and Robotics that help the scientific community to better understand the brain as well as design robotic devices and algorithms for interfacing humans and robots. The first part of the book introduces the idea of neuro-robotics, by presenting state-of-the-art bio-inspired devices. The second part of the book focuses on human-machine interfaces for pe

  20. The new era of minimally invasive interventions for prostate cancer: robot-assisted laparoscopic radical prostatectomy and focal therapy

    Directory of Open Access Journals (Sweden)

    Schatloff O

    2011-10-01

    Full Text Available Oscar Schatloff1, Alyssa S Louis2, Uri Lindner21Global Robotics Institute, Florida Hospital Celebration Health, Celebration, FL, USA; 2Division of Urology, Department of Surgical Oncology, University Health Network, Toronto, ON, CanadaAbstract: Prostate cancer remains a common but highly treatable disease. Innovations in prostate cancer treatment have allowed a transition toward minimally invasive approaches in an attempt to avoid treatment-related morbidities. In the middle of the treatment spectrum between radical open surgeries and active surveillance lies robot-assisted laparoscopic radical prostatectomy (RALP and focal therapy (FT. This review sets out the most current information on RALP and FT (including laser ablation, cryotherapy, high-intensity focused ultrasound, photodynamic therapy, and irreversible electroporation.Keywords: PCa, RALP, FT, laser ablation, cryotherapy, high-intensity focused ultrasound, photodynamic therapy, irreversible electroporation

  1. Robot 2015 : Second Iberian Robotics Conference : Advances in Robotics

    CERN Document Server

    Moreira, António; Lima, Pedro; Montano, Luis; Muñoz-Martinez, Victor

    2016-01-01

    This book contains a selection of papers accepted for presentation and discussion at ROBOT 2015: Second Iberian Robotics Conference, held in Lisbon, Portugal, November 19th-21th, 2015. ROBOT 2015 is part of a series of conferences that are a joint organization of SPR – “Sociedade Portuguesa de Robótica/ Portuguese Society for Robotics”, SEIDROB – Sociedad Española para la Investigación y Desarrollo de la Robótica/ Spanish Society for Research and Development in Robotics and CEA-GTRob – Grupo Temático de Robótica/ Robotics Thematic Group. The conference organization had also the collaboration of several universities and research institutes, including: University of Minho, University of Porto, University of Lisbon, Polytechnic Institute of Porto, University of Aveiro, University of Zaragoza, University of Malaga, LIACC, INESC-TEC and LARSyS. Robot 2015 was focussed on the Robotics scientific and technological activities in the Iberian Peninsula, although open to research and delegates from other...

  2. Is there life after Buckley's Formocresol? Part I -- a narrative review of alternative interventions and materials.

    Science.gov (United States)

    Srinivasan, V; Patchett, C L; Waterhouse, P J

    2006-03-01

    (1) To present a narrative review of the currently available alternative interventions and materials to formocresol pulpotomy for the management of extensive caries in the primary molar, and (2) to produce a clinical protocol for pulp therapy techniques in the extensively carious primary molar. The International Agency for Research on Cancer has recently classified formaldehyde as carcinogenic to human beings. Since Buckley's Formocresol contains 19% formaldehyde in its full strength and, therefore, 1% in a 20% dilution, a safer alternative should be identified. A narrative review of the published literature for primary molar pulp therapy techniques was undertaken following an extensive and appropriate literature search. A specialist group of paediatric dentists was formed to arrive at a consensus and establish an evidence-based protocol for the management of extensively carious primary molar teeth. Part I of this paper explores the currently available alternative interventions and materials to formocresol in the form of a narrative review. The second part of the paper will present the formation of a specialist group to arrive at a consensus and establish an evidence-based protocol for the management of the extensively carious primary molar. After consideration of a review of extensively searched literature, a protocol and key points document have been developed to assist clinicians in their treatment planning. Further long-term studies with the highest level of evidence (i.e. randomized controlled trials) are required to enable us to identify acceptable alternatives which can replace formocresol.

  3. Congruence between patient characteristics and interventions may partly explain medication adherence intervention effectiveness: an analysis of 190 randomized controlled trials from a Cochrane systematic review.

    Science.gov (United States)

    Allemann, Samuel S; Nieuwlaat, Robby; Navarro, Tamara; Haynes, Brian; Hersberger, Kurt E; Arnet, Isabelle

    2017-11-01

    Due to the negative outcomes of medication nonadherence, interventions to improve adherence have been the focus of countless studies. The congruence between adherence-related patient characteristics and interventions may partly explain the variability of effectiveness in medication adherence studies. In their latest update of a Cochrane review reporting inconsistent effects of adherence interventions, the authors offered access to their database for subanalysis. We aimed to use this database to assess congruence between adherence-related patient characteristics and interventions and its association with intervention effects. We developed a congruence score consisting of six features related to inclusion criteria, patient characteristics at baseline, and intervention design. Two independent raters extracted and scored items from the 190 studies available in the Cochrane database. We correlated overall congruence score and individual features with intervention effects regarding adherence and clinical outcomes using Kruskal-Wallis rank sum test and Fisher's exact test. Interrater reliability for newly extracted data was almost perfect with a Cohen's Kappa of 0.92 [95% confidence interval (CI) = 0.89-0.94; P congruence score nor any other individual feature (i.e., "determinants of nonadherence as inclusion criteria," "tailoring of interventions to the inclusion criteria," "reasons for nonadherence assessed at baseline," "adjustment of intervention to individual patient needs," and "theory-based interventions") was significantly associated with intervention effects. The presence of only six studies that included nonadherent patients and the interdependency of this feature with the remaining five might preclude a conclusive assessment of congruence between patient characteristics and adherence interventions. In order to obtain clinical benefits from effective adherence interventions, we encourage researchers to focus on the inclusion of nonadherent patients. Copyright

  4. Human-like behavior of robot arms: general considerations and the handwriting task-part II: The robot arm in handwriting

    NARCIS (Netherlands)

    Potkonjak, V.; Kostic, D.; Tzafestas, S.; Popovic, M.; Lazarevic, M.; Djordjevic, G.

    2001-01-01

    This paper (Part II) investigates the motion of a redundant anthropomorphic arm during the writing task. Two approaches are applied. The first is based on the concept of distributed positioning which is suitable to model the "writing" task before the occurrence of fatigue symptoms. The second

  5. Motor modules in robot-aided walking

    Directory of Open Access Journals (Sweden)

    Gizzi Leonardo

    2012-10-01

    Full Text Available Abstract Background It is hypothesized that locomotion is achieved by means of rhythm generating networks (central pattern generators and muscle activation generating networks. This modular organization can be partly identified from the analysis of the muscular activity by means of factorization algorithms. The activity of rhythm generating networks is described by activation signals whilst the muscle intervention generating network is represented by motor modules (muscle synergies. In this study, we extend the analysis of modular organization of walking to the case of robot-aided locomotion, at varying speed and body weight support level. Methods Non Negative Matrix Factorization was applied on surface electromyographic signals of 8 lower limb muscles of healthy subjects walking in gait robotic trainer at different walking velocities (1 to 3km/h and levels of body weight support (0 to 30%. Results The muscular activity of volunteers could be described by low dimensionality (4 modules, as for overground walking. Moreover, the activation signals during robot-aided walking were bursts of activation timed at specific phases of the gait cycle, underlying an impulsive controller, as also observed in overground walking. This modular organization was consistent across the investigated speeds, body weight support level, and subjects. Conclusions These results indicate that walking in a Lokomat robotic trainer is achieved by similar motor modules and activation signals as overground walking and thus supports the use of robotic training for re-establishing natural walking patterns.

  6. Evolutionary robotics

    Indian Academy of Sciences (India)

    In evolutionary robotics, a suitable robot control system is developed automatically through evolution due to the interactions between the robot and its environment. It is a complicated task, as the robot and the environment constitute a highly dynamical system. Several methods have been tried by various investigators to ...

  7. Robot Aesthetics

    DEFF Research Database (Denmark)

    Jochum, Elizabeth Ann; Putnam, Lance Jonathan

    This paper considers art-based research practice in robotics through a discussion of our course and relevant research projects in autonomous art. The undergraduate course integrates basic concepts of computer science, robotic art, live performance and aesthetic theory. Through practice...... in robotics research (such as aesthetics, culture and perception), we believe robot aesthetics is an important area for research in contemporary aesthetics....

  8. Filigree Robotics

    DEFF Research Database (Denmark)

    Tamke, Martin; Evers, Henrik Leander; Clausen Nørgaard, Esben

    2016-01-01

    Filigree Robotics experiments with the combination of traditional ceramic craft with robotic fabrication in order to generate a new narrative of fine three-dimensional ceramic ornament for architecture.......Filigree Robotics experiments with the combination of traditional ceramic craft with robotic fabrication in order to generate a new narrative of fine three-dimensional ceramic ornament for architecture....

  9. Achievements and prospects of robotics in dismantling operations

    International Nuclear Information System (INIS)

    Clement, G.; Goetghebeur, S.; Ravera, J.P.

    1993-01-01

    After a definition of 'robotic systems' (poly functionality is the main concept), the nuclear facilities that have used robotic systems for their dismantling are reviewed; the various robot intervention domains in dismantling, the different types of machines and the work carried out by robots are presented. Difficulties arising from robot utilization for reactor dismantling, robot design considerations, reliability, personnel training needs, tooling and costs are discussed. Applicability criteria are derived concerning radio protection, hard working conditions, task complexity, multiplicity and quality, and costs

  10. Overview of States' Use of Telehealth for the Delivery of Early Intervention (IDEA Part C Services

    Directory of Open Access Journals (Sweden)

    Jana Cason

    2012-12-01

    Full Text Available Background: Early intervention (EI services are designed to promote the development of skills and enhance the quality of life of infants and toddlers who have been identified as having a disability or developmental delay, enhance capacity of families to care for their child with special needs, reduce future educational costs, and promote independent living (NECTAC 2011.  EI services are regulated by Part C of the Individuals with Disabilities Education Improvement Act (IDEA; however, personnel shortages, particularly in rural areas, limit access for children who qualify.  Telehealth is an emerging delivery model demonstrating potential to deliver EI services effectively and efficiently, thereby improving access and ameliorating the impact of provider shortages in underserved areas. The use of a telehealth delivery model facilitates inter-disciplinary collaboration, coordinated care, and consultation with specialists not available within a local community.  Method:  A survey sent by the National Early Childhood Technical Assistance Center (NECTAC to IDEA Part C coordinators assessed their utilization of telehealth within states’ IDEA Part C programs.  Reimbursement for provider type and services and barriers to implement a telehealth service delivery model were identified.  Results:  Representatives from 26 states and one jurisdiction responded to the NECTAC telehealth survey.  Of these, 30% (n=9 indicated that they are either currently using telehealth as an adjunct service delivery model (n=6 or plan to incorporate telehealth within the next 1-2 years (n=3.  Identified telehealth providers included developmental specialists, teachers of the Deaf/Hard of Hearing (DHH, speech-language pathologists, occupational therapists, physical therapists, behavior specialists, audiologists, and interpreters.  Reimbursement was variable and included use of IDEA Part C funding, Medicaid, and private insurance.  Expressed barriers and concerns for

  11. Soft Robotics - The Next Industrial Revolution?

    OpenAIRE

    Rossiter, Jonathan M; Hauser, Helmut

    2016-01-01

    The robot dance has, since its inception in 1967, been a caricature of how robots move. Its imitation of the series of precise, linear motions with abrupt starts and stops is instantly recognizable. Despite a certain wavering in its popularity, it remains part of modern culture. What is so remarkable about the robot dance is that it mimics the movements and constraints of conventional rigid robots, a type of robot that is ubiquitous in automated manufacturing and object handling, and it could...

  12. 75 FR 5603 - Part C Early Intervention Services Grant Under the Ryan White HIV/AIDS Program

    Science.gov (United States)

    2010-02-03

    ... DEPARTMENT OF HEALTH AND HUMAN SERVICES Health Resources and Services Administration Part C Early Intervention Services Grant Under the Ryan White HIV/AIDS Program AGENCY: Health Resources and Services Administration (HRSA), HHS. ACTION: Notice of noncompetitive award of Part C funds for Saint Michael's Medical...

  13. 76 FR 30951 - Part C Early Intervention Services Grant Under the Ryan White HIV/AIDS Program

    Science.gov (United States)

    2011-05-27

    ... Intervention Services Grant Under the Ryan White HIV/AIDS Program AGENCY: Health Resources and Services... White HIV/AIDS Program, Part C Funds for the Tutwiler Clinic. SUMMARY: HRSA will award non-competitively Ryan White HIV/AIDS Program, Part C funds to the Tutwiler Clinic, Tutwiler, Mississippi, to support...

  14. 78 FR 25458 - Ryan White HIV/AIDS Program, Part C Early Intervention Services Grant Under the Ryan White HIV...

    Science.gov (United States)

    2013-05-01

    ... HIV/AIDS Program, Part C Early Intervention Services Grant Under the Ryan White HIV/AIDS Program AGENCY: Health Resources and Services Administration (HRSA), HHS. ACTION: Notice of Ryan White HIV/AIDS... HIV/AIDS, HRSA will provide a one-time noncompetitive Ryan White HIV/AIDS Program Part C funds award...

  15. Socially intelligent robots: dimensions of human-robot interaction.

    Science.gov (United States)

    Dautenhahn, Kerstin

    2007-04-29

    Social intelligence in robots has a quite recent history in artificial intelligence and robotics. However, it has become increasingly apparent that social and interactive skills are necessary requirements in many application areas and contexts where robots need to interact and collaborate with other robots or humans. Research on human-robot interaction (HRI) poses many challenges regarding the nature of interactivity and 'social behaviour' in robot and humans. The first part of this paper addresses dimensions of HRI, discussing requirements on social skills for robots and introducing the conceptual space of HRI studies. In order to illustrate these concepts, two examples of HRI research are presented. First, research is surveyed which investigates the development of a cognitive robot companion. The aim of this work is to develop social rules for robot behaviour (a 'robotiquette') that is comfortable and acceptable to humans. Second, robots are discussed as possible educational or therapeutic toys for children with autism. The concept of interactive emergence in human-child interactions is highlighted. Different types of play among children are discussed in the light of their potential investigation in human-robot experiments. The paper concludes by examining different paradigms regarding 'social relationships' of robots and people interacting with them.

  16. Experiences of a Motivational Interview Delivered by a Robot: Qualitative Study.

    Science.gov (United States)

    Galvão Gomes da Silva, Joana; Kavanagh, David J; Belpaeme, Tony; Taylor, Lloyd; Beeson, Konna; Andrade, Jackie

    2018-05-03

    Motivational interviewing is an effective intervention for supporting behavior change but traditionally depends on face-to-face dialogue with a human counselor. This study addressed a key challenge for the goal of developing social robotic motivational interviewers: creating an interview protocol, within the constraints of current artificial intelligence, which participants will find engaging and helpful. The aim of this study was to explore participants' qualitative experiences of a motivational interview delivered by a social robot, including their evaluation of usability of the robot during the interaction and its impact on their motivation. NAO robots are humanoid, child-sized social robots. We programmed a NAO robot with Choregraphe software to deliver a scripted motivational interview focused on increasing physical activity. The interview was designed to be comprehensible even without an empathetic response from the robot. Robot breathing and face-tracking functions were used to give an impression of attentiveness. A total of 20 participants took part in the robot-delivered motivational interview and evaluated it after 1 week by responding to a series of written open-ended questions. Each participant was left alone to speak aloud with the robot, advancing through a series of questions by tapping the robot's head sensor. Evaluations were content-analyzed utilizing Boyatzis' steps: (1) sampling and design, (2) developing themes and codes, and (3) validating and applying the codes. Themes focused on interaction with the robot, motivation, change in physical activity, and overall evaluation of the intervention. Participants found the instructions clear and the navigation easy to use. Most enjoyed the interaction but also found it was restricted by the lack of individualized response from the robot. Many positively appraised the nonjudgmental aspect of the interview and how it gave space to articulate their motivation for change. Some participants felt that the

  17. In Pipe Robot with Hybrid Locomotion System

    Directory of Open Access Journals (Sweden)

    Cristian Miclauş

    2015-06-01

    Full Text Available The first part of the paper covers aspects concerning in pipe robots and their components, such as hybrid locomotion systems and the adapting mechanisms used. The second part describes the inspection robot that was developed, which combines tracked and wheeled locomotion (hybrid locomotion. The end of the paper presents the advantages and disadvantages of the proposed robot.

  18. Robotics: A Bridge for Education and Technology.

    Science.gov (United States)

    Warnat, Winifred I.

    Robotics (robot usage) is discussed from a historical perspective with regard to its role in employment and education. Part 1 examines the transition from an industrial to an information society and speculates what the future might hold, particularly in terms of employment. Part 2 gives a historical overview of the robotics industry and discusses…

  19. Evaluation of automated decisionmaking methodologies and development of an integrated robotic system simulation, volume 2, part 1. Appendix A: Software documentation

    Science.gov (United States)

    Lowrie, J. W.; Fermelia, A. J.; Haley, D. C.; Gremban, K. D.; Vanbaalen, J.; Walsh, R. W.

    1982-01-01

    Documentation of the preliminary software developed as a framework for a generalized integrated robotic system simulation is presented. The program structure is composed of three major functions controlled by a program executive. The three major functions are: system definition, analysis tools, and post processing. The system definition function handles user input of system parameters and definition of the manipulator configuration. The analysis tools function handles the computational requirements of the program. The post processing function allows for more detailed study of the results of analysis tool function executions. Also documented is the manipulator joint model software to be used as the basis of the manipulator simulation which will be part of the analysis tools capability.

  20. A Robotic Guide for Blind People. Part 1. A Multi-National Survey of the Attitudes, Requirements and Preferences of Potential End-Users

    Directory of Open Access Journals (Sweden)

    Marion A. Hersh

    2010-01-01

    Full Text Available This paper reports the results of a multi-national survey in several different countries on the attitudes, requirements and preferences of blind and visually impaired people for a robotic guide. The survey is introduced by a brief overview of existing work on robotic travel aids and other mobile robotic devices. The questionnaire comprises three sections on personal information about respondents, existing use of mobility and navigation devices and the functions and other features of a robotic guide. The survey found that respondents were very interested in the robotic guide having a number of different functions and being useful in a wide range of circumstances. They considered the robot's appearance to be very important but did not like any of the proposed designs. From their comments, respondents wanted the robot to be discreet and inconspicuous, small, light weight and portable, easy to use, robust to damage, require minimal maintenance, have a long life and a long battery life.

  1. ARIES NDA Robot operators' manual

    International Nuclear Information System (INIS)

    Scheer, N.L.; Nelson, D.C.

    1998-05-01

    The ARIES NDA Robot is an automation device for servicing the material movements for a suite of Non-destructive assay (NDA) instruments. This suite of instruments includes a calorimeter, a gamma isotopic system, a segmented gamma scanner (SGS), and a neutron coincidence counter (NCC). Objects moved by the robot include sample cans, standard cans, and instrument plugs. The robot computer has an RS-232 connection with the NDA Host computer, which coordinates robot movements and instrument measurements. The instruments are expected to perform measurements under the direction of the Host without operator intervention. This user's manual describes system startup, using the main menu, manual operation, and error recovery

  2. Complex pharmaceutical care intervention in pulmonary care Part B. Patient opinion and process survey

    NARCIS (Netherlands)

    Stuurman-Bieze, A.GG; Kokenberg, M.E.A.P.; Tobi, H; de Boer, W.O.; van Doormaal, Jasperien E.; de Jong-van den Berg, Lolkje Theodora Wilhelmina; Tromp, Th.F.J.

    2005-01-01

    Objective: The IPMP study (Interventions on the principle of Pulmonary Medication Profiles) investigates and describes the results of complex pharmaceutical care interventions provided to selected pulmonary patients to improve their drug use. This paper describes the patients' opinions about the

  3. Robotic systems in spine surgery.

    Science.gov (United States)

    Onen, Mehmet Resid; Naderi, Sait

    2014-01-01

    Surgical robotic systems have been available for almost twenty years. The first surgical robotic systems were designed as supportive systems for laparoscopic approaches in general surgery (the first procedure was a cholecystectomy in 1987). The da Vinci Robotic System is the most common system used for robotic surgery today. This system is widely used in urology, gynecology and other surgical disciplines, and recently there have been initial reports of its use in spine surgery, for transoral access and anterior approaches for lumbar inter-body fusion interventions. SpineAssist, which is widely used in spine surgery, and Renaissance Robotic Systems, which are considered the next generation of robotic systems, are now FDA approved. These robotic systems are designed for use as guidance systems in spine instrumentation, cement augmentations and biopsies. The aim is to increase surgical accuracy while reducing the intra-operative exposure to harmful radiation to the patient and operating team personnel during the intervention. We offer a review of the published literature related to the use of robotic systems in spine surgery and provide information on using robotic systems.

  4. An example of the use of robotics in French nuclear power plants the ISIS robot

    International Nuclear Information System (INIS)

    Seguy, J.; Thirion, H.

    1988-01-01

    The authors report how Robotics in French nuclear power plants (NPP) is used to solve maintenance problems. One of the most typical example of the use of robotics in French NPP is the ISIS robot. The first generation of this robot has performed the repair of corroded upper internal structures in Chinon A3 gaz cooled reactor. Two robots of this type have successfully welded more than 200 repair parts in the core without major failure during more than 12,000 hours

  5. Mergeable nervous systems for robots.

    Science.gov (United States)

    Mathews, Nithin; Christensen, Anders Lyhne; O'Grady, Rehan; Mondada, Francesco; Dorigo, Marco

    2017-09-12

    Robots have the potential to display a higher degree of lifetime morphological adaptation than natural organisms. By adopting a modular approach, robots with different capabilities, shapes, and sizes could, in theory, construct and reconfigure themselves as required. However, current modular robots have only been able to display a limited range of hardwired behaviors because they rely solely on distributed control. Here, we present robots whose bodies and control systems can merge to form entirely new robots that retain full sensorimotor control. Our control paradigm enables robots to exhibit properties that go beyond those of any existing machine or of any biological organism: the robots we present can merge to form larger bodies with a single centralized controller, split into separate bodies with independent controllers, and self-heal by removing or replacing malfunctioning body parts. This work takes us closer to robots that can autonomously change their size, form and function.Robots that can self-assemble into different morphologies are desired to perform tasks that require different physical capabilities. Mathews et al. design robots whose bodies and control systems can merge and split to form new robots that retain full sensorimotor control and act as a single entity.

  6. Robotic environments

    NARCIS (Netherlands)

    Bier, H.H.

    2011-01-01

    Technological and conceptual advances in fields such as artificial intelligence, robotics, and material science have enabled robotic architectural environments to be implemented and tested in the last decade in virtual and physical prototypes. These prototypes are incorporating sensing-actuating

  7. Experiences of a Motivational Interview Delivered by a Robot: Qualitative Study

    Science.gov (United States)

    Galvão Gomes da Silva, Joana; Kavanagh, David J; Belpaeme, Tony; Taylor, Lloyd; Beeson, Konna

    2018-01-01

    Background Motivational interviewing is an effective intervention for supporting behavior change but traditionally depends on face-to-face dialogue with a human counselor. This study addressed a key challenge for the goal of developing social robotic motivational interviewers: creating an interview protocol, within the constraints of current artificial intelligence, which participants will find engaging and helpful. Objective The aim of this study was to explore participants’ qualitative experiences of a motivational interview delivered by a social robot, including their evaluation of usability of the robot during the interaction and its impact on their motivation. Methods NAO robots are humanoid, child-sized social robots. We programmed a NAO robot with Choregraphe software to deliver a scripted motivational interview focused on increasing physical activity. The interview was designed to be comprehensible even without an empathetic response from the robot. Robot breathing and face-tracking functions were used to give an impression of attentiveness. A total of 20 participants took part in the robot-delivered motivational interview and evaluated it after 1 week by responding to a series of written open-ended questions. Each participant was left alone to speak aloud with the robot, advancing through a series of questions by tapping the robot’s head sensor. Evaluations were content-analyzed utilizing Boyatzis’ steps: (1) sampling and design, (2) developing themes and codes, and (3) validating and applying the codes. Results Themes focused on interaction with the robot, motivation, change in physical activity, and overall evaluation of the intervention. Participants found the instructions clear and the navigation easy to use. Most enjoyed the interaction but also found it was restricted by the lack of individualized response from the robot. Many positively appraised the nonjudgmental aspect of the interview and how it gave space to articulate their motivation for

  8. Healthcare Robotics

    OpenAIRE

    Riek, Laurel D.

    2017-01-01

    Robots have the potential to be a game changer in healthcare: improving health and well-being, filling care gaps, supporting care givers, and aiding health care workers. However, before robots are able to be widely deployed, it is crucial that both the research and industrial communities work together to establish a strong evidence-base for healthcare robotics, and surmount likely adoption barriers. This article presents a broad contextualization of robots in healthcare by identifying key sta...

  9. Facts, fallacies, and politics of comparative effectiveness research: Part 2 - implications for interventional pain management.

    Science.gov (United States)

    Manchikanti, Laxmaiah; Falco, Frank J E; Boswell, Mark V; Hirsch, Joshua A

    2010-01-01

    times it becomes an orphan. Part 2 of this comprehensive review will provide facts, fallacies, and politics of CER along with discussion of potential outcomes, impact of CER on health care delivery, and implications for interventional pain management in the United States.

  10. Clean-room robot implementation

    International Nuclear Information System (INIS)

    Comeau, J.L.

    1982-01-01

    A robot has been incorporated in a clean room operation in which vacuum tube parts are cleaned just prior to final assembly with a 60 lb/in 2 blast of argon gas. The robot is programmed to pick up the parts, manipulate/rotate them as necessary in the jet pattern and deposit them in a tray precleaned by the robot. A carefully studied implementation plan was followed in the procurement, installation, modification and programming of the robot facility. An unusual configuration of one tube part required a unique gripper design. A study indicated that the tube parts processed by the robot are 12% cleaner than those manually cleaned by an experienced operator

  11. Industrial Robots.

    Science.gov (United States)

    Reed, Dean; Harden, Thomas K.

    Robots are mechanical devices that can be programmed to perform some task of manipulation or locomotion under automatic control. This paper discusses: (1) early developments of the robotics industry in the United States; (2) the present structure of the industry; (3) noneconomic factors related to the use of robots; (4) labor considerations…

  12. Feasibility of using a humanoid robot to elicit communicational response in children with mild autism

    Science.gov (United States)

    Malik, Norjasween Abdul; Shamsuddin, Syamimi; Yussof, Hanafiah; Azfar Miskam, Mohd; Che Hamid, Aminullah

    2013-12-01

    Research evidences are accumulating with regards to the potential use of robots for the rehabilitation of children with autism. The purpose of this paper is to elaborate on the results of communicational response in two children with autism during interaction with the humanoid robot NAO. Both autistic subjects in this study have been diagnosed with mild autism. Following the outcome from our first pilot study; the aim of this current experiment is to explore the application of NAO robot to engage with a child and further teach about emotions through a game-centered and song-based approach. The experiment procedure involved interaction between humanoid robot NAO with each child through a series of four different modules. The observation items are based on ten items selected and referenced to GARS-2 (Gilliam Autism Rating Scale-second edition) and also input from clinicians and therapists. The results clearly indicated that both of the children showed optimistic response through the interaction. Negative responses such as feeling scared or shying away from the robot were not detected. Two-way communication between the child and robot in real time significantly gives positive impact in the responses towards the robot. To conclude, it is feasible to include robot-based interaction specifically to elicit communicational response as a part of the rehabilitation intervention of children with autism.

  13. 75 FR 73110 - Part C Early Intervention Services Grant under the Ryan White HIV/AIDS Program

    Science.gov (United States)

    2010-11-29

    ... Intervention Services Grant under the Ryan White HIV/AIDS Program AGENCY: Health Resources and Services.../AIDS Program, Part C funds for the Louisiana State University, Health Sciences Center, Viral Disease... HIV/AIDS, including primary medical care, laboratory testing, oral health care, outpatient mental...

  14. 75 FR 54898 - Part C Early Intervention Services Grant Under the Ryan White HIV/AIDS Program

    Science.gov (United States)

    2010-09-09

    ... Intervention Services Grant Under the Ryan White HIV/AIDS Program AGENCY: Health Resources and Services... Part C funds under The Ryan White HIV/AIDS Program to support comprehensive primary care services for persons living with HIV/AIDS, including primary medical care, laboratory testing, oral health care...

  15. Robot Mechanisms

    CERN Document Server

    Lenarcic, Jadran; Stanišić, Michael M

    2013-01-01

    This book provides a comprehensive introduction to the area of robot mechanisms, primarily considering industrial manipulators and humanoid arms. The book is intended for both teaching and self-study. Emphasis is given to the fundamentals of kinematic analysis and the design of robot mechanisms. The coverage of topics is untypical. The focus is on robot kinematics. The book creates a balance between theoretical and practical aspects in the development and application of robot mechanisms, and includes the latest achievements and trends in robot science and technology.

  16. Traveling Robots and Their Cultural Baggage

    DEFF Research Database (Denmark)

    Blond, Lasse

    When social robots are imported from Asia to Europe they bring along with them a cultural luggage consisting of foreign sociotechnical imaginary. The effort to adopt the robot Silbot to Nordic social services exposed unfamiliar and cultural-dependent views of care, cognition, health and human...... nature. Studying Silbot in “the wild” highlighted these issues as well as the human-robot interaction and the adaptation of the robot to real life praxis. The importance of comprehending robots as parts of sociotechnical ensembles is emphasized as well as the observance of how robots are shaped...... by the cultural context in the recipient countries....

  17. The Maiden Voyage of a Kinematics Robot

    Science.gov (United States)

    Greenwolfe, Matthew L.

    2015-04-01

    In a Montessori preschool classroom, students work independently on tasks that absorb their attention in part because the apparatus are carefully designed to make mistakes directly observable and limit exploration to one aspect or dimension. Control of error inheres in the apparatus itself, so that teacher intervention can be minimal.1 Inspired by this example, I created a robotic kinematics apparatus that also shapes the inquiry experience. Students program the robot by drawing kinematic graphs on a computer and then observe its motion. Exploration is at once limited to constant velocity and constant acceleration motion, yet open to complex multi-segment examples difficult to achieve in the lab in other ways. The robot precisely and reliably produces the motion described by the students' graphs, so that the apparatus itself provides immediate visual feedback about whether their understanding is correct as they are free to explore within the hard-coded limits. In particular, the kinematic robot enables hands-on study of multi-segment constant velocity situations, which lays a far stronger foundation for the study of accelerated motion. When correction is anonymous—just between one group of lab partners and their robot—students using the kinematic robot tend to flow right back to work because they view the correction as an integral part of the inquiry learning process. By contrast, when correction occurs by the teacher and/or in public (e.g., returning a graded assignment or pointing out student misconceptions during class), students all too often treat the event as the endpoint to inquiry. Furthermore, quantitative evidence shows a large gain from pre-test to post-test scores using the Test of Understanding Graphs in Kinematics (TUG-K).

  18. Robot Futures

    DEFF Research Database (Denmark)

    Christoffersen, Anja; Grindsted Nielsen, Sally; Jochum, Elizabeth Ann

    Robots are increasingly used in health care settings, e.g., as homecare assistants and personal companions. One challenge for personal robots in the home is acceptance. We describe an innovative approach to influencing the acceptance of care robots using theatrical performance. Live performance...... is a useful testbed for developing and evaluating what makes robots expressive; it is also a useful platform for designing robot behaviors and dialogue that result in believable characters. Therefore theatre is a valuable testbed for studying human-robot interaction (HRI). We investigate how audiences...... perceive social robots interacting with humans in a future care scenario through a scripted performance. We discuss our methods and initial findings, and outline future work....

  19. Effectiveness of brief interventions as part of the Screening, Brief Intervention and Referral to Treatment (SBIRT) model for reducing the nonmedical use of psychoactive substances: a systematic review.

    Science.gov (United States)

    Young, Matthew M; Stevens, Adrienne; Galipeau, James; Pirie, Tyler; Garritty, Chantelle; Singh, Kavita; Yazdi, Fatemeh; Golfam, Mohammed; Pratt, Misty; Turner, Lucy; Porath-Waller, Amy; Arratoon, Cheryl; Haley, Nancy; Leslie, Karen; Reardon, Rhoda; Sproule, Beth; Grimshaw, Jeremy; Moher, David

    2014-05-24

    The purpose of this systematic review is to assess the effectiveness of brief interventions (BIs) as part of the Screening, Brief Intervention, and Referral to Treatment (SBIRT) model for reducing the nonmedical use of psychoactive substances. Bibliographic databases (including MEDLINE, Embase, The Cochrane Library, CINAHL, and PsycINFO to April 2012) and gray literature sources were searched. We included randomized controlled trials that opportunistically screened adolescents or adults and then provided a one-to-one, verbal BI to those at risk of substance-use harm. Of interest was the nonmedical use of psychoactive substances (for example, drugs prohibited by international law), excluding alcohol, nicotine, and caffeine. Interventions comprised four or fewer sessions and were compared with no/delayed intervention or provision of information only. Studies were assessed for bias using the Cochrane risk of bias tool. Results were synthesized narratively. Evidence was interpreted according to the GRADE framework. We identified 8,836 records. Of these, five studies met our inclusion criteria. Two studies compared BI with no BI, and three studies compared BI with information only. Studies varied in characteristics such as substances targeted, screening procedures, and BI administered. Outcomes were mostly reported by a single study, leading to limited or uncertain confidence in effect estimates. Insufficient evidence exists as to whether BIs, as part of SBIRT, are effective or ineffective for reducing the use of, or harms associated with nonmedical use of, psychoactive substances when these interventions are administered to nontreatment-seeking, screen-detected populations. Updating this review with emerging evidence will be important. CRD42012002414.

  20. Feasibility and acceptance of a robotic surgery ergonomic training program.

    Science.gov (United States)

    Franasiak, Jason; Craven, Renatta; Mosaly, Prithima; Gehrig, Paola A

    2014-01-01

    Assessment of ergonomic strain during robotic surgery indicates there is a need for intervention. However, limited data exist detailing the feasibility and acceptance of ergonomic training (ET) for robotic surgeons. This prospective, observational pilot study evaluates the implementation of an evidence-based ET module. A two-part survey was conducted. The first survey assessed robotic strain using the Nordic Musculoskeletal Questionnaire (NMQ). Participants were given the option to participate in either an online or an in-person ET session. The ET was derived from Occupational Safety and Health Administration guidelines and developed by a human factors engineer experienced with health care ergonomics. After ET, a follow-up survey including the NMQ and an assessment of the ET were completed. The survey was sent to 67 robotic surgeons. Forty-two (62.7%) responded, including 18 residents, 8 fellows, and 16 attending physicians. Forty-five percent experienced strain resulting from performing robotic surgery and 26.3% reported persistent strain. Only 16.6% of surgeons reported prior ET in robotic surgery. Thirty-five (78%) surgeons elected to have in-person ET, which was successfully arranged for 32 surgeons (91.4%). Thirty-seven surgeons (88.1%) completed the follow-up survey. All surgeons participating in the in-person ET found it helpful and felt formal ET should be standard, 88% changed their practice as a result of the training, and 74% of those reporting strain noticed a decrease after their ET. Thus, at a high-volume robotics center, evidence-based ET was easily implemented, well-received, changed some surgeons' practice, and decreased self-reported strain related to robotic surgery.

  1. Pyrotechnic robot - constructive design and command

    Directory of Open Access Journals (Sweden)

    Ionel A. Staretu

    2013-10-01

    Full Text Available Pyrotechnic robots are service robots used to reduce the time for intervention of pyrotechnic troops and to diminish the danger for the operators. Pyrotechnic robots are used to inspect dangerous areas or/and to remove and to distroy explosive or suspicious devices/objects. These robots can be used to make corridors through mined battle fields, for manipulation and neutralization of unexploded ammunition, for inspection of vehicles, trains, airplanes and buildings. For these robots, a good functional activity is determined with regard to work space dimensions,, robotic arm kinematics and gripper characteristics. The paper shows the structural, kinematic, static synthesis and analysis as well as the design and functional simulation of the robotic arm and the grippers attached on the pyrotechnic robot designed by the authors.

  2. Social Robots as Persuasive Agents

    DEFF Research Database (Denmark)

    Vlachos, Evgenios; Schärfe, Henrik

    2014-01-01

    Robots are more and more used in a social context, and in this paper we try to formulate a research agenda concerning ethical issues around social HRI in order to be prepared for future scenarios where robots may be a naturally integrated part of human society. We outline different paradigms to d...... to describe the role of social robots in communication processes with humans, and connect HRI with the topic of persuasive technology in health care, to critically reflect the potential benefits of using social robots as persuasive agents....

  3. Contribution to automatic image recognition. Application to analysis of plain scenes of overlapping parts in robot technology

    International Nuclear Information System (INIS)

    Tan, Shengbiao

    1987-01-01

    A method for object modeling and overlapped object automatic recognition is presented. Our work is composed of three essential parts: image processing, object modeling, and evaluation of the implementation of the stated concepts. In the first part, we present a method of edge encoding which is based on a re-sampling of the data encoded according to Freeman, this method generates an isotropic, homogenous and very precise representation. The second part relates to object modeling. This important step makes much easier the recognition work. The new method proposed characterizes a model with two groups of information: the description group containing the primitives, the discrimination group containing data packs, called 'transition vectors'. Based on this original method of information organization, a 'relative learning' is able to select, to ignore and to update the information concerning the objects already learned, according to the new information to be included into the data base. The recognition is a two-pass process: the first pass determines very efficiently the presence of objects by making use of each object's particularities, and this hypothesis is either confirmed or rejected by the following fine verification pass. The last part describes in detail the experimentation results. We demonstrate the robustness of the algorithms with images in both poor lighting and overlapping objects conditions. The system, named SOFIA, has been installed into an industrial vision system series and works in real time. (author) [fr

  4. Hexapod Robot

    Science.gov (United States)

    Begody, Ericka

    2016-01-01

    right or up and down. The hexapod will eventually be able to track the object moving its head and body in sync with on another and being able to rotate its body at 360 degrees. This is the plans and possible end results for the hexapod robot I will be working on during my summer internship at NASA Johnson Space Center. Since working on the hexapod project I have gained an increase interest in robotics. I enjoy the process of critical thinking. Also will working on this project I was challenged in a way that made more passionate to strive even more to become an engineer. I've learned that asking questions is an important part of the learning process. Also I learn that much more is accomplished when teamwork is applied.

  5. Digital Emotion : How Audiences React to Robots on Screen

    OpenAIRE

    Damian Schofield,

    2018-01-01

    The experience of interacting with robots is becoming a more pervasive part of our day-to-day life. When considering the experience of interacting with other technologies and artefacts, interaction with robots presents a distinct and potentially unique component: physical connection. Robots share our physical space; this is a prominent part of the interaction experience. Robots offer a lifelike presence and the Human-Robot Interaction (HRI) issues go beyond the traditional interactions of mor...

  6. What makes a robot 'social'?

    Science.gov (United States)

    Jones, Raya A

    2017-08-01

    Rhetorical moves that construct humanoid robots as social agents disclose tensions at the intersection of science and technology studies (STS) and social robotics. The discourse of robotics often constructs robots that are like us (and therefore unlike dumb artefacts). In the discourse of STS, descriptions of how people assimilate robots into their activities are presented directly or indirectly against the backdrop of actor-network theory, which prompts attributing agency to mundane artefacts. In contradistinction to both social robotics and STS, it is suggested here that to view a capacity to partake in dialogical action (to have a 'voice') is necessary for regarding an artefact as authentically social. The theme is explored partly through a critical reinterpretation of an episode that Morana Alač reported and analysed towards demonstrating her bodies-in-interaction concept. This paper turns to 'body' with particular reference to Gibsonian affordances theory so as to identify the level of analysis at which dialogicality enters social interactions.

  7. Robots in Elderly Care

    Directory of Open Access Journals (Sweden)

    Alessandro Vercelli

    2018-03-01

    new signs and symptoms through artificial intelligence by machine learning and deep learning and about his/her habitat. On the other, this powerful instrument may represent a dramatic treat to the privacy of the subjects and their caregivers. Therefore, robotics represents an ethically sensitive field. Care robotics bear the risk of reducing human contact, of increasing the objectification and loss of control of the elderly, of losing the privacy and personal freedom of the individual (especially when robots may perform restrictive interventions. Moreover, the use of robots in elderly care may raise in the risk of confusing between reality and appearance, with a potential risk of deception and infantilization of the elder.

  8. Mobile robotics research at Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Morse, W.D.

    1998-09-01

    Sandia is a National Security Laboratory providing scientific and engineering solutions to meet national needs for both government and industry. As part of this mission, the Intelligent Systems and Robotics Center conducts research and development in robotics and intelligent machine technologies. An overview of Sandia`s mobile robotics research is provided. Recent achievements and future directions in the areas of coordinated mobile manipulation, small smart machines, world modeling, and special application robots are presented.

  9. Afterword: Robot Conceptualizations Between Continuity and Innovation

    Directory of Open Access Journals (Sweden)

    Leopoldina Fortunati

    2013-01-01

    Full Text Available The aim of this afterword is to discuss a topic that links all the papers presented in this special issue. This transversal topic is the forms of social robots. Firstly, social robots form is discussed in light of the forms of robotics we have inherited from the past. This includes the models of society that each of them embodied, as well as the social logic of the emotions connected to them. Secondly, social robots form is analyzed in light of the arrival in a new area for robotics, that of robots in the domestic sphere. Here, the system of filters created by the mass appropriation of information and communication technologies in the last two decades, has set the premise for a change of the social contract that has made social robot penetration possible. Whilst exploring the models and the meanings of social robots in the domestic sphere it emerges that robotics is following two different paths: one addressing the material part of housework (more traditional robotics and the other addressing the immaterial part of reproduction work (more innovative robotics. Finally, the paper analyzes the dematerialization process of social robotics that is still taking place, a practice that is defined herein as “ubiquitous social roboting.”

  10. Oak Ridge National Laboratory Technology Logic Diagram. Volume 3, Technology evaluation data sheets: Part C, Robotics/automation, Waste management

    Energy Technology Data Exchange (ETDEWEB)

    1993-09-01

    The Oak Ridge National Laboratory Technology Logic Diagram (TLD) was developed to provide a decision support tool that relates environmental restoration (ER) and waste management (WM) problems at Oak Ridge National Laboratory (ORNL) to potential technologies that can remediate these problems. The TLD identifies the research, development, demonstration testing, and evaluation needed to develop these technologies to a state that allows technology transfer and application to decontamination and decommissioning (D&D), remedial action (RA), and WM activities. The TLD consists of three fundamentally separate volumes: Vol. 1, Technology Evaluation; Vol. 2, Technology Logic Diagram and Vol. 3, Technology EvaLuation Data Sheets. Part A of Vols. 1 and 2 focuses on RA. Part B of Vols. 1 and 2 focuses on the D&D of contaminated facilities. Part C of Vols. 1 and 2 focuses on WM. Each part of Vol. 1 contains an overview of the TM, an explanation of the problems facing the volume-specific program, a review of identified technologies, and rankings of technologies applicable to the site. Volume 2 (Pts. A. B. and C) contains the logic linkages among EM goals, environmental problems, and the various technologies that have the potential to solve these problems. Volume 3 (Pts. A. B, and C) contains the TLD data sheets. This volume provides the technology evaluation data sheets (TEDS) for ER/WM activities (D&D, RA and WM) that are referenced by a TEDS code number in Vol. 2 of the TLD. Each of these sheets represents a single logic trace across the TLD. These sheets contain more detail than is given for the technologies in Vol. 2.

  11. Robotic buildings(s)

    NARCIS (Netherlands)

    Bier, H.H.

    2014-01-01

    Technological and conceptual advances in fields such as artificial intelligence, robotics, and material science have enabled robotic building to be in the last decade prototypically implemented. In this context, robotic building implies both physically built robotic environments and robotically

  12. Group interventions for patients with cancer and HIV disease: part IV. Clinical and policy recommendations.

    Science.gov (United States)

    Leszcz, Molyn; Sherman, Allen; Mosier, Julie; Burlingame, Gary M; Cleary, Trish; Ulman, Kathleen Hubbs; Simonton, Stephanie; Latif, Umaira; Strauss, Bernhard; Hazelton, Lara

    2004-10-01

    Group interventions have assumed a growing role in primary prevention and supportive care for cancer and HIV disease. Earlier sections of this Special Report examined empirical findings for these interventions and provided recommendations for future research. The current section offers brief recommendations for service providers, policymakers, and stakeholders. Group services now occupy an increasingly prominent place in primary prevention programs and medical settings. In previous sections of this Special Report (Sherman, Leszcz et al., 2004; Sherman, Mosier et al., 2004a, 2004b) we examined the efficacy of different group interventions at different phases of cancer or HIV disease, considered characteristics of the intervention and the participants that might influence outcomes, and discussed mechanisms of action. Methodological challenges and priorities for future research were highlighted. In this, the final section, we offer brief recommendations for service providers, policymakers, and other stakeholders. We consider some of the barriers that constrain use of empirically-based group interventions and note how these programs might be implemented more widely and effectively.

  13. Rapid 3D Modeling and Parts Recognition on Automotive Vehicles Using a Network of RGB-D Sensors for Robot Guidance

    Directory of Open Access Journals (Sweden)

    Alberto Chávez-Aragón

    2013-01-01

    Full Text Available This paper presents an approach for the automatic detection and fast 3D profiling of lateral body panels of vehicles. The work introduces a method to integrate raw streams from depth sensors in the task of 3D profiling and reconstruction and a methodology for the extrinsic calibration of a network of Kinect sensors. This sensing framework is intended for rapidly providing a robot with enough spatial information to interact with automobile panels using various tools. When a vehicle is positioned inside the defined scanning area, a collection of reference parts on the bodywork are automatically recognized from a mosaic of color images collected by a network of Kinect sensors distributed around the vehicle and a global frame of reference is set up. Sections of the depth information on one side of the vehicle are then collected, aligned, and merged into a global RGB-D model. Finally, a 3D triangular mesh modelling the body panels of the vehicle is automatically built. The approach has applications in the intelligent transportation industry, automated vehicle inspection, quality control, automatic car wash systems, automotive production lines, and scan alignment and interpretation.

  14. Nutritional Intervention as part of Functional Rehabilitation in Older People with reduced functional ability

    DEFF Research Database (Denmark)

    Beck, Anne Marie; Dent, Elsa; Baldwin, Christine

    2016-01-01

    body weight, hand-grip strength or muscle strength. There was no difference between groups in the critical outcomes; balance, cognition, activities of daily living and mortality at long-term follow-up. Nutritional intervention given with functional rehabilitation was associated with an increased...... studies considered to be clinical homogenous were combined in a meta-analysis Results Of the 788 studies screened, five were identified for inclusion. Nutritional intervention given with functional rehabilitation improved energy and protein intake, although it failed to provide any improvement in final....... Conclusions This meta-analysis highlights concerns regarding the quality of the randomisation of participants at baseline. Future high-quality research is essential to establish whether older people with loss of functional abilities can benefit from nutritional intervention....

  15. Comparative costs and cost-effectiveness of behavioural interventions as part of HIV prevention strategies.

    Science.gov (United States)

    Hsu, Justine; Zinsou, Cyprien; Parkhurst, Justin; N'Dour, Marguerite; Foyet, Léger; Mueller, Dirk H

    2013-01-01

    Behavioural interventions have been widely integrated in HIV/AIDS social marketing prevention strategies and are considered valuable in settings with high levels of risk behaviours and low levels of HIV/AIDS awareness. Despite their widespread application, there is a lack of economic evaluations comparing different behaviour change communication methods. This paper analyses the costs to increase awareness and the cost-effectiveness to influence behaviour change for five interventions in Benin. Cost and cost-effectiveness analyses used economic costs and primary effectiveness data drawn from surveys. Costs were collected for provider inputs required to implement the interventions in 2009 and analysed by 'person reached'. Cost-effectiveness was analysed by 'person reporting systematic condom use'. Sensitivity analyses were performed on all uncertain variables and major assumptions. Cost-per-person reached varies by method, with public outreach events the least costly (US$2.29) and billboards the most costly (US$25.07). Influence on reported behaviour was limited: only three of the five interventions were found to have a significant statistical correlation with reported condom use (i.e. magazines, radio broadcasts, public outreach events). Cost-effectiveness ratios per person reporting systematic condom use resulted in the following ranking: magazines, radio and public outreach events. Sensitivity analyses indicate rankings are insensitive to variation of key parameters although ratios must be interpreted with caution. This analysis suggests that while individual interventions are an attractive use of resources to raise awareness, this may not translate into a cost-effective impact on behaviour change. The study found that the extensive reach of public outreach events did not seem to influence behaviour change as cost-effectively when compared with magazines or radio broadcasts. Behavioural interventions are context-specific and their effectiveness influenced by a

  16. Paying for Early Interventions in Psychoses: A Three-Part Model.

    Science.gov (United States)

    Frank, Richard G; Glied, Sherry A; McGuire, Thomas G

    2015-07-01

    Widespread dissemination of early interventions for psychosis, such as the intervention offered in the RAISE study (Recovery After an Initial Schizophrenia Episode), requires a funding mechanism that is both compatible with approaches already used by payers and generates incentives for providers that promote the desired behaviors. The authors propose a funding model with three components: a prospective per-case payment made conditional on patient engagement in treatment, a per-service component to cover the costs of clinical services, and an outcome-based component conditional on achieving measurable outcome milestones. The authors describe the components and how such a payment mechanism might be implemented.

  17. Soft Robotics.

    Science.gov (United States)

    Whitesides, George M

    2018-04-09

    This description of "soft robotics" is not intended to be a conventional review, in the sense of a comprehensive technical summary of a developing field. Rather, its objective is to describe soft robotics as a new field-one that offers opportunities to chemists and materials scientists who like to make "things" and to work with macroscopic objects that move and exert force. It will give one (personal) view of what soft actuators and robots are, and how this class of soft devices fits into the more highly developed field of conventional "hard" robotics. It will also suggest how and why soft robotics is more than simply a minor technical "tweak" on hard robotics and propose a unique role for chemistry, and materials science, in this field. Soft robotics is, at its core, intellectually and technologically different from hard robotics, both because it has different objectives and uses and because it relies on the properties of materials to assume many of the roles played by sensors, actuators, and controllers in hard robotics. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  18. Anatomy-Based Organization of Modular Robots

    DEFF Research Database (Denmark)

    Christensen, David Johan; Campbell, Jason

    2008-01-01

    This paper presents a novel biologically inspired hierarchical approach to organizing and controlling modular robots. The purpose of our approach is to decompose the complexity of assembling and commanding a functional robot made of numerous simple modules (thousands to millions) by introducing...... a hierarchy of structure and control. The robots we describe incorporate anatomically inspired parts such as muscles, bones and joints, and these parts in turn are assembled from modules. Each of those parts encapsulates one or more functions, e.g. a muscle can contract. Control of the robot can then be cast...... as a problem of controlling its anatomical parts rather than each discrete module. We show simulation results from experiments using gradient-based primitives to control parts of increasingly complex robots, including snake, crawler, cilia-surface, arm-joint-muscle and grasping robots. We conclude...

  19. The burden of disaster: part II. applying interventions across the child's social ecology.

    Science.gov (United States)

    Pfefferbaum, Rose L; Jacobs, Anne K; Noffsinger, Mary A; Pfefferbaum, Betty; Sherrieb, Kathleen; Norris, Fran H

    2012-01-01

    This second of two articles describes the application of disaster mental health interventions within the context of the childs social ecology consisting of the Micro-, Meso-, Exo-, and Macrosystems. Microsystem interventions involving parents, siblings, and close friends include family preparedness planning andpractice, psychoeducation, role modeling, emotional support, and redirection. Mesosystem interventions provided by schools and faith-based organizations include safety and support, assessment, referral, and counseling. Exosystem interventions include those provided through community-based mental health programs, healthcare organizations, the workplace, the media, local volunteer disaster organizations, and other local organizations. Efforts to build community resilience to disasters are likely to have influence through the Exosystem. The Macrosystem - including the laws, history, cultural and subcultural characteristics, and economic and social conditions that underlie the other systems - affects the child indirectly through public policies and disaster programs and services that become available in the child's Exosystem in the aftermath of a disaster The social ecology paradigm, described more fully in a companion article (Noffsinger Pfefferbaum, Pfefferbaum, Sherrieb, & Norris,2012), emphasizes relationships among systems and can guide the development and delivery of services embedded in naturally-occurring structures in the child's environment.

  20. European clinical guidelines for Tourette syndrome and other tic disorders. Part III: behavioural and psychosocial interventions

    DEFF Research Database (Denmark)

    Verdellen, Cara; van de Griendt, Jolande; Hartmann, Andreas

    2011-01-01

    This clinical guideline provides recommendations for the behavioural and psychosocial interventions (BPI) of children and adolescents with tic disorders prepared by a working group of the European Society for the Study of Tourette Syndrome (ESSTS). A systematic literature search was conducted...... to obtain an update on the efficacy of BPI for tics. Relevant studies were identified using computerised searches of the Medline and PsycINFO databases and the Cochrane Library for the years 1950-2010. The search identified no meta-analyses, yet twelve (systematic) reviews and eight randomised controlled...... trials provided evidence for the current review. Most evidence was found for habit reversal training (HRT) and the available but smaller evidence also supports the efficacy of exposure with response prevention (ERP). Both interventions are considered first line behavioural treatments for tics for both...

  1. Pharmacological Interventions Including Medical Injections for Neck Pain: An Overview as Part of the ICON§ Project

    Science.gov (United States)

    Peloso, Paul M; Khan, Mahweesh; Gross, Anita R; Carlesso, Lisa; Santaguida, Lina; Lowcock, Janet; MacDermid, Joy C; Walton, Dave; Goldsmith, Charlie H; Langevin, Pierre; Shi, Qiyun

    2013-01-01

    Objectives: To conduct an overview (review-of-reviews) on pharmacological interventions for neck pain. Search Strategy: Computerized databases and grey literature were searched from 2006 to 2012. Selection Criteria: Systematic reviews of randomized controlled trials (RCT) in adults with acute to chronic neck pain reporting effects of pharmacological interventions including injections on pain, function/disability, global perceived effect, quality of life and patient satisfaction. Data Collection & Analysis: Two independent authors selected articles, assessed risk of bias and extracted data The GRADE tool was used to evaluate the body of evidence and an external panel provided critical review. Main Results: We found 26 reviews reporting on 47 RCTs. Most pharmacological interventions had low to very low quality methodologic evidence with three exceptions. For chronic neck pain, there was evidence of: a small immediate benefit for eperison hydrochloride (moderate GRADE, 1 trial, 157 participants);no short-term pain relieving benefit for botulinum toxin-A compared to saline (strong GRADE; 5 trial meta-analysis, 258 participants) nor for subacute/chronic whiplash (moderate GRADE; 4 trial meta-analysis, 183 participants) including reduced pain, disability or global perceived effect; andno long-term benefit for medial branch block of facet joints with steroids (moderate GRADE; 1 trial, 120 participants) over placebo to reduce pain or disability; Reviewers' Conclusions: While in general there is a lack of evidence for most pharmacological interventions, current evidence is against botulinum toxin-A for chronic neck pain or subacute/chronic whiplash; against medial branch block with steroids for chronic facet joint pain; but in favour of the muscle relaxant eperison hydrochloride for chronic neck pain. PMID:24155805

  2. The approach of cancer related fatigue in rehabilitation medicine: Part II – Therapeutic interventions

    OpenAIRE

    Salca Amalia; Checiches Alexandra; Irsay Laszlo

    2015-01-01

    Starting with patient’ diagnose and continuing throughout the treatment and thereafter, cancer-related fatigue (CRF) is a distressing and disabling symptom, highly prevalent across the cancer continuum2. This is a review article mainly focusing on the rehabilitation objectives and interventions in CRF, and implementation issues, according to the report of an NCCN member institution4. Implementation is the most problematic, considering the large number of patients to whom it is addressed to...

  3. Robotics 101

    Science.gov (United States)

    Sultan, Alan

    2011-01-01

    Robots are used in all kinds of industrial settings. They are used to rivet bolts to cars, to move items from one conveyor belt to another, to gather information from other planets, and even to perform some very delicate types of surgery. Anyone who has watched a robot perform its tasks cannot help but be impressed by how it works. This article…

  4. Vitruvian Robot

    DEFF Research Database (Denmark)

    Hasse, Cathrine

    2017-01-01

    future. A real version of Ava would not last long in a human world because she is basically a solipsist, who does not really care about humans. She cannot co-create the line humans walk along. The robots created as ‘perfect women’ (sex robots) today are very far from the ideal image of Ava...

  5. The approach of cancer related fatigue in rehabilitation medicine: Part II – Therapeutic interventions

    Directory of Open Access Journals (Sweden)

    Salca Amalia

    2015-09-01

    Full Text Available Starting with patient’ diagnose and continuing throughout the treatment and thereafter, cancer-related fatigue (CRF is a distressing and disabling symptom, highly prevalent across the cancer continuum2. This is a review article mainly focusing on the rehabilitation objectives and interventions in CRF, and implementation issues, according to the report of an NCCN member institution4. Implementation is the most problematic, considering the large number of patients to whom it is addressed to and the variety of pathologies within this group of patients. The onset of CRF is difficult to establish, because of the limitations of reporting this symptom4, but it is a valuable predictor in prognosis. The main interventions in rehabilitation applicable to these patients are discussed in correlation to the objectives of each phase of therapeutic management in cancer: pre-operatory, before, during or after radio and/or chemotherapy Conclusion: Rehabilitation interventions should be applied to all patients diagnosed with cancer, according to their phase of oncologic treatment and the objectives. This should be practiced as preventive measure, but as a therapeutic one to, considering the high incidence of CFR before diagnose.

  6. Collision-free motion coordination of heterogeneous robots

    International Nuclear Information System (INIS)

    Ko, Nak Yong; Seo, Dong Jin; Simmons, Reid G.

    2008-01-01

    This paper proposes a method to coordinate the motion of multiple heterogeneous robots on a network. The proposed method uses prioritization and avoidance. Priority is assigned to each robot; a robot with lower priority avoids the robots of higher priority. To avoid collision with other robots, elastic force and potential field force are used. Also, the method can be applied separately to the motion planning of a part of a robot from that of the other parts of the robot. This is useful for application to the robots of the type mobile manipulator or highly redundant robots. The method is tested by simulation, and it results in smooth and adaptive coordination in an environment with multiple heterogeneous robots

  7. Collision-free motion coordination of heterogeneous robots

    Energy Technology Data Exchange (ETDEWEB)

    Ko, Nak Yong [Chosun University, Gwangju (Korea, Republic of); Seo, Dong Jin [RedOne Technologies, Gwangju (Korea, Republic of); Simmons, Reid G. [Carnegie Mellon University, Pennsylvania (United States)

    2008-11-15

    This paper proposes a method to coordinate the motion of multiple heterogeneous robots on a network. The proposed method uses prioritization and avoidance. Priority is assigned to each robot; a robot with lower priority avoids the robots of higher priority. To avoid collision with other robots, elastic force and potential field force are used. Also, the method can be applied separately to the motion planning of a part of a robot from that of the other parts of the robot. This is useful for application to the robots of the type mobile manipulator or highly redundant robots. The method is tested by simulation, and it results in smooth and adaptive coordination in an environment with multiple heterogeneous robots

  8. White Paper: Interventional MRI: Current Status and Potential for Development Considering Economic Perspectives, Part 1: General Application.

    Science.gov (United States)

    Barkhausen, Jörg; Kahn, Thomas; Krombach, Gabriele A; Kuhl, Christiane K; Lotz, Joachim; Maintz, David; Ricke, Jens; Schönberg, Stefan O; Vogl, Thomas J; Wacker, Frank K

    2017-07-01

    children with congenital heart defects and for atrial ablation at individual centers. Greater application can be expected in the future.. Citation format · Barkhausen J, Kahn T, Krombach GA et al. White Paper: Interventional MRI: Current Status and Potential for Development Considering Economic Perspectives, Part 1: General Application. Fortschr Röntgenstr 2017; 189: 611 - 623. © Georg Thieme Verlag KG Stuttgart · New York.

  9. From an Idea to a Working Robot Prototype: Distributing Knowledge of Robotics through Science Museum Workshops

    Science.gov (United States)

    Polishuk, Alexander; Verner, Igor; Mir, Ronen

    This paper presents our experience of teaching robotics to primary and middle school students at the Gelfand Center for Model Building, Robotics & Communication which is part of the Israel National Museum of Science, Technology and Space (MadaTech). The educational study examines the value and characteristics of students’ teamwork in the museum robotics workshops.

  10. Physical Human Robot Interaction for a Wall Mounting Robot - External Force Estimation

    DEFF Research Database (Denmark)

    Alonso García, Alejandro; Villarmarzo Arruñada, Noelia; Pedersen, Rasmus

    2018-01-01

    The use of collaborative robots enhances human capabilities, leading to better working conditions and increased productivity. In building construction, such robots are needed, among other tasks, to install large glass panels, where the robot takes care of the heavy lifting part of the job while...

  11. Robot Teachers

    DEFF Research Database (Denmark)

    Nørgård, Rikke Toft; Ess, Charles Melvin; Bhroin, Niamh Ni

    The world's first robot teacher, Saya, was introduced to a classroom in Japan in 2009. Saya, had the appearance of a young female teacher. She could express six basic emotions, take the register and shout orders like 'be quiet' (The Guardian, 2009). Since 2009, humanoid robot technologies have...... developed. It is now suggested that robot teachers may become regular features in educational settings, and may even 'take over' from human teachers in ten to fifteen years (cf. Amundsen, 2017 online; Gohd, 2017 online). Designed to look and act like a particular kind of human; robot teachers mediate human...... existence and roles, while also aiming to support education through sophisticated, automated, human-like interaction. Our paper explores the design and existential implications of ARTIE, a robot teacher at Oxford Brookes University (2017, online). Drawing on an initial empirical exploration we propose...

  12. Robot vision

    International Nuclear Information System (INIS)

    Hall, E.L.

    1984-01-01

    Almost all industrial robots use internal sensors such as shaft encoders which measure rotary position, or tachometers which measure velocity, to control their motions. Most controllers also provide interface capabilities so that signals from conveyors, machine tools, and the robot itself may be used to accomplish a task. However, advanced external sensors, such as visual sensors, can provide a much greater degree of adaptability for robot control as well as add automatic inspection capabilities to the industrial robot. Visual and other sensors are now being used in fundamental operations such as material processing with immediate inspection, material handling with adaption, arc welding, and complex assembly tasks. A new industry of robot vision has emerged. The application of these systems is an area of great potential

  13. Social Robots

    DEFF Research Database (Denmark)

    Social robotics is a cutting edge research area gathering researchers and stakeholders from various disciplines and organizations. The transformational potential that these machines, in the form of, for example, caregiving, entertainment or partner robots, pose to our societies and to us as indiv......Social robotics is a cutting edge research area gathering researchers and stakeholders from various disciplines and organizations. The transformational potential that these machines, in the form of, for example, caregiving, entertainment or partner robots, pose to our societies and to us...... as individuals seems to be limited by our technical limitations and phantasy alone. This collection contributes to the field of social robotics by exploring its boundaries from a philosophically informed standpoint. It constructively outlines central potentials and challenges and thereby also provides a stable...

  14. Micro intelligence robot

    International Nuclear Information System (INIS)

    Jeon, Yon Ho

    1991-07-01

    This book gives descriptions of micro robot about conception of robots and micro robot, match rules of conference of micro robots, search methods of mazes, and future and prospect of robots. It also explains making and design of 8 beat robot like making technique, software, sensor board circuit, and stepping motor catalog, speedy 3, Mr. Black and Mr. White, making and design of 16 beat robot, such as micro robot artist, Jerry 2 and magic art of shortening distances algorithm of robot simulation.

  15. An Intelligent Robot Programing

    Energy Technology Data Exchange (ETDEWEB)

    Hong, Seong Yong

    2012-01-15

    This book introduces an intelligent robot programing with background of the begging, introduction of VPL, and SPL, building of environment for robot platform, starting of robot programing, design of simulation environment, robot autonomy drive control programing, simulation graphic. Such as SPL graphic programing graphical image and graphical shapes, and graphical method application, application of procedure for robot control, robot multiprogramming, robot bumper sensor programing, robot LRF sencor programing and robot color sensor programing.

  16. An Intelligent Robot Programing

    International Nuclear Information System (INIS)

    Hong, Seong Yong

    2012-01-01

    This book introduces an intelligent robot programing with background of the begging, introduction of VPL, and SPL, building of environment for robot platform, starting of robot programing, design of simulation environment, robot autonomy drive control programing, simulation graphic. Such as SPL graphic programing graphical image and graphical shapes, and graphical method application, application of procedure for robot control, robot multiprogramming, robot bumper sensor programing, robot LRF sencor programing and robot color sensor programing.

  17. Multiprocessor development for robot control

    International Nuclear Information System (INIS)

    Lee, Jong Min; Kim, Seung Ho; Hwang, Suk Yeoung; Sohn, Surg Won; Kim, Byung Soo; Kim, Chang Hoi; Lee, Yong Bum; Kim, Woong Ki

    1988-12-01

    The object of this project is to develop a multiprocessor system which is essential to robot technology. A multiprocessor system interconnecting many single board computer is much faster and flexible than a single processor. The developed multiprocessor will be used to control nuclear mobile robot, so a loosely coupled system is adopted as a robot controller. A total configuration of controller is divided into three main parts in related with its function. It is consisted of supervisory control part, functional control part, remote control part. The designed control system is to be expanded easily for further use with a modular architecture, so the functional independency within sub-systems can be obtained throughout the system structure. Electromagnetic interference affecting to the control system is minimized by using optical fiber as communication media between robot and control system. System performances is enhanced not only by using distributed architecture in hardware, but by adopting real-time, multi-tasking operating system in software. The iRMX86 OS is used and reconfigured for real-time, multi-tasking operation. RS-485 serial communication protocol is used between functional control part and remote control part. Since the developed multiprocessor control system is an essential and fundamental technology for artificial intelligent robot, the result of this project can be applied directly to nuclear mobile robot. (Author)

  18. The Effects of Rhythm and Robotic Interventions on the Imitation/Praxis, Interpersonal Synchrony, and Motor Performance of Children with Autism Spectrum Disorder (ASD): A Pilot Randomized Controlled Trial

    Science.gov (United States)

    Srinivasan, Sudha M.; Kaur, Maninderjit; Park, Isabel K.; Gifford, Timothy D.; Marsh, Kerry L.; Bhat, Anjana N.

    2015-01-01

    We assessed the effects of three interventions, rhythm, robotic, and standard-of-care, on the imitation/praxis, interpersonal synchrony, and overall motor performance of 36 children with Autism Spectrum Disorder (ASD) between 5 and 12 years of age. Children were matched on age, level of functioning, and services received, prior to random assignment to one of the three groups. Training was provided for 8 weeks with 4 sessions provided each week. We assessed generalized changes in motor skills from the pretest to the posttest using a standardized test of motor performance, the Bruininks-Oseretsky Test of Motor Proficiency, 2nd edition (BOT-2). We also assessed training-specific changes in imitation/praxis and interpersonal synchrony during an early and a late session. Consistent with the training activities practiced, the rhythm and robot groups improved on the body coordination composite of the BOT-2, whereas the comparison group improved on the fine manual control composite of the BOT-2. All three groups demonstrated improvements in imitation/praxis. The rhythm and robot groups also showed improved interpersonal synchrony performance from the early to the late session. Overall, socially embedded movement-based contexts are valuable in promoting imitation/praxis, interpersonal synchrony, and motor performance and should be included within the standard-of-care treatment for children with ASD. PMID:26793394

  19. The Effects of Rhythm and Robotic Interventions on the Imitation/Praxis, Interpersonal Synchrony, and Motor Performance of Children with Autism Spectrum Disorder (ASD: A Pilot Randomized Controlled Trial

    Directory of Open Access Journals (Sweden)

    Sudha M. Srinivasan

    2015-01-01

    Full Text Available We assessed the effects of three interventions, rhythm, robotic, and standard-of-care, on the imitation/praxis, interpersonal synchrony, and overall motor performance of 36 children with Autism Spectrum Disorder (ASD between 5 and 12 years of age. Children were matched on age, level of functioning, and services received, prior to random assignment to one of the three groups. Training was provided for 8 weeks with 4 sessions provided each week. We assessed generalized changes in motor skills from the pretest to the posttest using a standardized test of motor performance, the Bruininks-Oseretsky Test of Motor Proficiency, 2nd edition (BOT-2. We also assessed training-specific changes in imitation/praxis and interpersonal synchrony during an early and a late session. Consistent with the training activities practiced, the rhythm and robot groups improved on the body coordination composite of the BOT-2, whereas the comparison group improved on the fine manual control composite of the BOT-2. All three groups demonstrated improvements in imitation/praxis. The rhythm and robot groups also showed improved interpersonal synchrony performance from the early to the late session. Overall, socially embedded movement-based contexts are valuable in promoting imitation/praxis, interpersonal synchrony, and motor performance and should be included within the standard-of-care treatment for children with ASD.

  20. Automatic Operation For A Robot Lawn Mower

    Science.gov (United States)

    Huang, Y. Y.; Cao, Z. L.; Oh, S. J.; Kattan, E. U.; Hall, E. L.

    1987-02-01

    A domestic mobile robot, lawn mower, which performs the automatic operation mode, has been built up in the Center of Robotics Research, University of Cincinnati. The robot lawn mower automatically completes its work with the region filling operation, a new kind of path planning for mobile robots. Some strategies for region filling of path planning have been developed for a partly-known or a unknown environment. Also, an advanced omnidirectional navigation system and a multisensor-based control system are used in the automatic operation. Research on the robot lawn mower, especially on the region filling of path planning, is significant in industrial and agricultural applications.

  1. Handling uncertainty and networked structure in robot control

    CERN Document Server

    Tamás, Levente

    2015-01-01

    This book focuses on two challenges posed in robot control by the increasing adoption of robots in the everyday human environment: uncertainty and networked communication. Part I of the book describes learning control to address environmental uncertainty. Part II discusses state estimation, active sensing, and complex scenario perception to tackle sensing uncertainty. Part III completes the book with control of networked robots and multi-robot teams. Each chapter features in-depth technical coverage and case studies highlighting the applicability of the techniques, with real robots or in simulation. Platforms include mobile ground, aerial, and underwater robots, as well as humanoid robots and robot arms. Source code and experimental data are available at http://extras.springer.com. The text gathers contributions from academic and industry experts, and offers a valuable resource for researchers or graduate students in robot control and perception. It also benefits researchers in related areas, such as computer...

  2. Artificial heart for humanoid robot

    Science.gov (United States)

    Potnuru, Akshay; Wu, Lianjun; Tadesse, Yonas

    2014-03-01

    A soft robotic device inspired by the pumping action of a biological heart is presented in this study. Developing artificial heart to a humanoid robot enables us to make a better biomedical device for ultimate use in humans. As technology continues to become more advanced, the methods in which we implement high performance and biomimetic artificial organs is getting nearer each day. In this paper, we present the design and development of a soft artificial heart that can be used in a humanoid robot and simulate the functions of a human heart using shape memory alloy technology. The robotic heart is designed to pump a blood-like fluid to parts of the robot such as the face to simulate someone blushing or when someone is angry by the use of elastomeric substrates and certain features for the transport of fluids.

  3. Robot Wars: US Empire and geopolitics in the robotic age

    Science.gov (United States)

    Shaw, Ian GR

    2017-01-01

    How will the robot age transform warfare? What geopolitical futures are being imagined by the US military? This article constructs a robotic futurology to examine these crucial questions. Its central concern is how robots – driven by leaps in artificial intelligence and swarming – are rewiring the spaces and logics of US empire, warfare, and geopolitics. The article begins by building a more-than-human geopolitics to de-center the role of humans in conflict and foreground a worldly understanding of robots. The article then analyzes the idea of US empire, before speculating upon how and why robots are materializing new forms of proxy war. A three-part examination of the shifting spaces of US empire then follows: (1) Swarm Wars explores the implications of miniaturized drone swarming; (2) Roboworld investigates how robots are changing US military basing strategy and producing new topological spaces of violence; and (3) The Autogenic Battle-Site reveals how autonomous robots will produce emergent, technologically event-ful sites of security and violence – revolutionizing the battlespace. The conclusion reflects on the rise of a robotic US empire and its consequences for democracy. PMID:29081605

  4. Effects of Individual and Group Contingency Interventions on Attendance in Adolescent Part-Time Employees

    Science.gov (United States)

    Berkovits, Shira Melody; Sturmey, Peter; Alvero, Alicia M.

    2012-01-01

    This study examined the effects of individual and group monetary contingencies on the attendance of adolescent part-time employees. Attendance increased in both individual and group contingency phases; however staff questionnaire responses indicated a preference for the individual contingencies. Future research should consider staff acceptability…

  5. Dosimetry of Occupationally Exposed Persons in Diagnostic and Interventional Arteriography. Part 1: Assessment of Entrance Doses

    International Nuclear Information System (INIS)

    Kicken, P.J.H.; Kemerink, G.J.; Engelshoven, J.M.A. van

    1999-01-01

    The purpose of this study was to obtain representative quantitative information on exposure conditions and entrance doses of occupationally exposed persons (workers) in diagnostic and interventional arteriography. In a study in three hospitals all parameters of the X ray systems that are related to the exposure of workers were quantified with an automatic data acquisition system. Using LiF thermoluminescence dosemeters, entrance doses to workers were measured at the forehead, neck, thorax, abdomen, upper arms, hands and lower legs. Measurements were performed during 353 procedures, and it was found that exposure of workers was predominantly caused by fluoroscopy. Averaged over all procedures in the annual workload, entrance doses were below 120 μGy when an undercouch X ray tube and a mechanical contrast injector were used. For an overcouch tube the doses were higher. It is concluded that entrance doses are low, and that legally established annual dose limits are un-likely to be exceeded. (author)

  6. Systematic Review of Occupational Therapy and Adult Cancer Rehabilitation: Part 1. Impact of Physical Activity and Symptom Management Interventions.

    Science.gov (United States)

    Hunter, Elizabeth G; Gibson, Robert W; Arbesman, Marian; D'Amico, Mariana

    This article is the first part of a systematic review of evidence for the effectiveness of cancer rehabilitation interventions within the scope of occupational therapy that address the activity and participation needs of adult cancer survivors. This article focuses on the importance of physical activity and symptom management. Strong evidence supports the use of exercise for cancer-related fatigue and indicates that lymphedema is not exacerbated by exercise. Moderate evidence supports the use of yoga to relieve anxiety and depression and indicates that exercise as a whole may contribute to a return to precancer levels of sexual activity. The results of this review support inclusion of occupational therapy in cancer rehabilitation and reveal a significant need for more research to explore ways occupational therapy can positively influence the outcomes of cancer survivors. Part 2 of the review also appears in this issue. Copyright © 2017 by the American Occupational Therapy Association, Inc.

  7. Space Robotics Challenge

    Data.gov (United States)

    National Aeronautics and Space Administration — The Space Robotics Challenge seeks to infuse robot autonomy from the best and brightest research groups in the robotics community into NASA robots for future...

  8. Robotic arm

    International Nuclear Information System (INIS)

    Kwech, H.

    1989-01-01

    A robotic arm positionable within a nuclear vessel by access through a small diameter opening and having a mounting tube supported within the vessel and mounting a plurality of arm sections for movement lengthwise of the mounting tube as well as for movement out of a window provided in the wall of the mounting tube is disclosed. An end effector, such as a grinding head or welding element, at an operating end of the robotic arm, can be located and operated within the nuclear vessel through movement derived from six different axes of motion provided by mounting and drive connections between arm sections of the robotic arm. The movements are achieved by operation of remotely-controllable servo motors, all of which are mounted at a control end of the robotic arm to be outside the nuclear vessel. 23 figs

  9. Robotic surgery

    Science.gov (United States)

    ... with this type of surgery give it some advantages over standard endoscopic techniques. The surgeon can make ... Elsevier Saunders; 2015:chap 87. Muller CL, Fried GM. Emerging technology in surgery: Informatics, electronics, robotics. In: ...

  10. Robotic parathyroidectomy.

    Science.gov (United States)

    Okoh, Alexis Kofi; Sound, Sara; Berber, Eren

    2015-09-01

    Robotic parathyroidectomy has recently been described. Although the procedure eliminates the neck scar, it is technically more demanding than the conventional approaches. This report is a review of the patients' selection criteria, technique, and outcomes. © 2015 Wiley Periodicals, Inc.

  11. Light Robotics

    DEFF Research Database (Denmark)

    Glückstad, Jesper; Palima, Darwin

    Light Robotics - Structure-Mediated Nanobiophotonics covers the latest means of sculpting of both light and matter for achieving bioprobing and manipulation at the smallest scales. The synergy between photonics, nanotechnology and biotechnology spans the rapidly growing field of nanobiophotonics...

  12. Robotic arm

    Science.gov (United States)

    Kwech, Horst

    1989-04-18

    A robotic arm positionable within a nuclear vessel by access through a small diameter opening and having a mounting tube supported within the vessel and mounting a plurality of arm sections for movement lengthwise of the mounting tube as well as for movement out of a window provided in the wall of the mounting tube. An end effector, such as a grinding head or welding element, at an operating end of the robotic arm, can be located and operated within the nuclear vessel through movement derived from six different axes of motion provided by mounting and drive connections between arm sections of the robotic arm. The movements are achieved by operation of remotely-controllable servo motors, all of which are mounted at a control end of the robotic arm to be outside the nuclear vessel.

  13. Robotic nurse duties in the urology operative room: 11 years of experience

    Directory of Open Access Journals (Sweden)

    Ali Abdel Raheem

    2017-04-01

    Full Text Available The robotic nurse plays an essential role in a successful robotic surgery. As part of the robotic surgical team, the robotic nurse must demonstrate a high level of professional knowledge, and be an expert in robotic technology and dealing with robotic malfunctions. Each one of the robotic nursing team “nurse coordinator, scrub-nurse and circulating-nurse” has a certain job description to ensure maximum patient's safety and robotic surgical efficiency. Well-structured training programs should be offered to the robotic nurse to be well prepared, feel confident, and maintain high-quality of care.

  14. [Determinants of health and health policy. Part 3. From intervention of quality of life].

    Science.gov (United States)

    Zácek, A

    2000-03-29

    Effectiveness of outputs of a qualified intervention can be valued by several positive criteria corresponding to the "quality of life" conception, which is based on the feeling of the health and contentment. The finding that great differences in the income among different social groups in conditions of the liberal market society correlate with several health and social problems brought about to the hypothesis that the decrease of the differences in the income, accompanied by strengthening of various forms of the social cohesion, civic solidarity, legitimate equality, and ethical justice may substantially improve the health status of the population. The hypothesis has been verified in many epidemiological studies and found to be valid enough for the health policy and far-seeing economy. Analytics of the World Bank recommend to governments primary invest into the health of socially week groups in order to decrease their poverty and to keep social conciliation. World Health Organization (WHO) sets in its new program for Europe called "21 Goals for the 21st Century" that differences in the health status among the European states should diminish till 2020 by one third and within the countries by one quarter at least. Both goals should be achieved by a substantial improvement of the health status of the ill-adapted social groups and by significant improvement of those socioeconomical conditions which may have adverse effects namely on the differences in incomes, education and opportunities for employment.

  15. Preliminary clinical experience with a dedicated interventional robotic system for CT-guided biopsies of lung lesions: a comparison with the conventional manual technique

    International Nuclear Information System (INIS)

    Anzidei, Michele; Argiro, Renato; Porfiri, Andrea; Boni, Fabrizio; Zaccagna, Fulvio; Napoli, Alessandro; Leonardi, Andrea; Bezzi, Mario; Catalano, Carlo; Anile, Marco; Venuta, Federico; Vitolo, Domenico; Saba, Luca; Longo, Flavia

    2015-01-01

    Evaluate the performance of a robotic system for CT-guided lung biopsy in comparison to the conventional manual technique. One hundred patients referred for CT-guided lung biopsy were randomly assigned to group A (robot-assisted procedure) or group B (conventional procedure). Size, distance from entry point and position in lung of target lesions were evaluated to assess homogeneity differences between the two groups. Procedure duration, dose length product (DLP), precision of needle positioning, diagnostic performance of the biopsy and rate of complications were evaluated to assess the clinical performance of the robotic system as compared to the conventional technique. All biopsies were successfully performed. The size (p = 0.41), distance from entry point (p = 0.86) and position in lung (p = 0.32) of target lesions were similar in both groups (p = 0.05). Procedure duration and radiation dose were significantly reduced in group A as compared to group B (p = 0.001). Precision of needle positioning, diagnostic performance of the biopsy and rate of complications were similar in both groups (p = 0.05). Robot-assisted CT-guided lung biopsy can be performed safely and with high diagnostic accuracy, reducing procedure duration and radiation dose in comparison to the conventional manual technique. (orig.)

  16. Preliminary clinical experience with a dedicated interventional robotic system for CT-guided biopsies of lung lesions: a comparison with the conventional manual technique

    Energy Technology Data Exchange (ETDEWEB)

    Anzidei, Michele; Argiro, Renato; Porfiri, Andrea; Boni, Fabrizio; Zaccagna, Fulvio; Napoli, Alessandro; Leonardi, Andrea; Bezzi, Mario; Catalano, Carlo [University of Rome, Department of Radiological, Oncological and Anatomopathological Sciences - Radiology - Sapienza, Rome (Italy); Anile, Marco; Venuta, Federico [University of Rome, Department of Thoracic Surgery - Sapienza, Rome (Italy); Vitolo, Domenico [University of Rome, Department of Radiological, Oncological and Anatomopathological Sciences - Pathology - Sapienza, Rome (Italy); Saba, Luca [Department of Radiology, Azienda Ospedaliero Universitaria (A.O.U.), di Cagliari-Polo di Monserrato, Monserrato (Italy); Longo, Flavia [University of Rome, Department of Radiological, Oncological and Anatomopathological Sciences - Oncology - Sapienza, Rome (Italy)

    2015-05-01

    Evaluate the performance of a robotic system for CT-guided lung biopsy in comparison to the conventional manual technique. One hundred patients referred for CT-guided lung biopsy were randomly assigned to group A (robot-assisted procedure) or group B (conventional procedure). Size, distance from entry point and position in lung of target lesions were evaluated to assess homogeneity differences between the two groups. Procedure duration, dose length product (DLP), precision of needle positioning, diagnostic performance of the biopsy and rate of complications were evaluated to assess the clinical performance of the robotic system as compared to the conventional technique. All biopsies were successfully performed. The size (p = 0.41), distance from entry point (p = 0.86) and position in lung (p = 0.32) of target lesions were similar in both groups (p = 0.05). Procedure duration and radiation dose were significantly reduced in group A as compared to group B (p = 0.001). Precision of needle positioning, diagnostic performance of the biopsy and rate of complications were similar in both groups (p = 0.05). Robot-assisted CT-guided lung biopsy can be performed safely and with high diagnostic accuracy, reducing procedure duration and radiation dose in comparison to the conventional manual technique. (orig.)

  17. Supervisory control for a complex robotic system

    International Nuclear Information System (INIS)

    Miller, D.J.

    1988-01-01

    The Robotic Radiation Survey and Analysis System investigates the use of advanced robotic technology for performing remote radiation surveys on nuclear waste shipping casks. Robotic systems have the potential for reducing personnel exposure to radiation and providing fast reliable throughput at future repository sites. A primary technology issue is the integrated control of distributed specialized hardware through a modular supervisory software system. Automated programming of robot trajectories based upon mathematical models of the cask and robot coupled with sensory feedback enables flexible operation of a commercial gantry robot with the reliability needed to perform autonomous operations in a hazardous environment. Complexity is managed using structured software engineering techniques resulting in the generation of reusable command primitives which contribute to a software parts catalog for a generalized robot programming language

  18. Structural synthesis of parallel robots

    CERN Document Server

    Gogu, Grigore

    This book represents the fifth part of a larger work dedicated to the structural synthesis of parallel robots. The originality of this work resides in the fact that it combines new formulae for mobility, connectivity, redundancy and overconstraints with evolutionary morphology in a unified structural synthesis approach that yields interesting and innovative solutions for parallel robotic manipulators.  This is the first book on robotics that presents solutions for coupled, decoupled, uncoupled, fully-isotropic and maximally regular robotic manipulators with Schönflies motions systematically generated by using the structural synthesis approach proposed in Part 1.  Overconstrained non-redundant/overactuated/redundantly actuated solutions with simple/complex limbs are proposed. Many solutions are presented here for the first time in the literature. The author had to make a difficult and challenging choice between protecting these solutions through patents and releasing them directly into the public domain. T...

  19. Mobile Robots in Human Environments

    DEFF Research Database (Denmark)

    Svenstrup, Mikael

    intelligent mobile robotic devices capable of being a more natural and sociable actor in a human environment. More specific the emphasis is on safe and natural motion and navigation issues. First part of the work focus on developing a robotic system, which estimates human interest in interacting......, lawn mowers, toy pets, or as assisting technologies for care giving. If we want robots to be an even larger and more integrated part of our every- day environments, they need to become more intelligent, and behave safe and natural to the humans in the environment. This thesis deals with making...... as being able to navigate safely around one person, the robots must also be able to navigate in environments with more people. This can be environments such as pedestrian streets, hospital corridors, train stations or airports. The developed human-aware navigation strategy is enhanced to formulate...

  20. CANINE: a robotic mine dog

    Science.gov (United States)

    Stancil, Brian A.; Hyams, Jeffrey; Shelley, Jordan; Babu, Kartik; Badino, Hernán.; Bansal, Aayush; Huber, Daniel; Batavia, Parag

    2013-01-01

    Neya Systems, LLC competed in the CANINE program sponsored by the U.S. Army Tank Automotive Research Development and Engineering Center (TARDEC) which culminated in a competition held at Fort Benning as part of the 2012 Robotics Rodeo. As part of this program, we developed a robot with the capability to learn and recognize the appearance of target objects, conduct an area search amid distractor objects and obstacles, and relocate the target object in the same way that Mine dogs and Sentry dogs are used within military contexts for exploration and threat detection. Neya teamed with the Robotics Institute at Carnegie Mellon University to develop vision-based solutions for probabilistic target learning and recognition. In addition, we used a Mission Planning and Management System (MPMS) to orchestrate complex search and retrieval tasks using a general set of modular autonomous services relating to robot mobility, perception and grasping.

  1. Recent advances in robotics

    International Nuclear Information System (INIS)

    Beni, G.; Hackwood, S.

    1984-01-01

    Featuring 10 contributions, this volume offers a state-of-the-art report on robotic science and technology. It covers robots in modern industry, robotic control to help the disabled, kinematics and dynamics, six-legged walking robots, a vector analysis of robot manipulators, tactile sensing in robots, and more

  2. Intelligent control system for nuclear power plant mobile robot

    International Nuclear Information System (INIS)

    Koenig, A.; Lecoeur-Taibi, I.; Crochon, E.; Vacherand, F.

    1991-01-01

    In order to fully optimize the efficiency of the perception and navigation components available on a mobile robot, the upper level of a mobile robot control requires intelligence support to unload the work of the teleoperator. This knowledge-based system has to manage a priori data such as the map of the workspace, the mission, the characteristics of sensors and robot, but also, the current environment state and the running mission. It has to issue a plan to drive the sensors to focus on relevant objects or to scan the environment and to select the best algorithms depending on the current situation. The environment workspace is a nuclear power plant building. The teleoperated robot is a mobile wheeled or legged vehicle that moves inside the different floors of the building. There are three types of mission: radio-activity survey, inspection and intervention. To perform these goals the robot must avoid obstacles, pass through doors, possibly climb stairs and recognize valves and pipes. The perception control system has to provide the operator with a synthetic view of the surroundings. It manages background tasks such as obstacle detection and free space map building, and specific tasks such as beacon recognition for odometry relocalization and valve detection for maintenance. To do this, the system solves perception resources conflicts, taking into account the current states of the sensors and the current conditions such as lightness or darkness, cluttered scenes, sensor failure. A perception plan is issued from the mission goals, planned path, relocalization requirements and available perception resources. Basically, the knowledge-based system is implemented on a blackboard architecture which includes two parts: a top-down planning part and a bottom-up perception part. The results of the perception are continuously sent to the operator who can trigger new perception actions. (author)

  3. Mission Reliability Estimation for Repairable Robot Teams

    Science.gov (United States)

    Trebi-Ollennu, Ashitey; Dolan, John; Stancliff, Stephen

    2010-01-01

    A mission reliability estimation method has been designed to translate mission requirements into choices of robot modules in order to configure a multi-robot team to have high reliability at minimal cost. In order to build cost-effective robot teams for long-term missions, one must be able to compare alternative design paradigms in a principled way by comparing the reliability of different robot models and robot team configurations. Core modules have been created including: a probabilistic module with reliability-cost characteristics, a method for combining the characteristics of multiple modules to determine an overall reliability-cost characteristic, and a method for the generation of legitimate module combinations based on mission specifications and the selection of the best of the resulting combinations from a cost-reliability standpoint. The developed methodology can be used to predict the probability of a mission being completed, given information about the components used to build the robots, as well as information about the mission tasks. In the research for this innovation, sample robot missions were examined and compared to the performance of robot teams with different numbers of robots and different numbers of spare components. Data that a mission designer would need was factored in, such as whether it would be better to have a spare robot versus an equivalent number of spare parts, or if mission cost can be reduced while maintaining reliability using spares. This analytical model was applied to an example robot mission, examining the cost-reliability tradeoffs among different team configurations. Particularly scrutinized were teams using either redundancy (spare robots) or repairability (spare components). Using conservative estimates of the cost-reliability relationship, results show that it is possible to significantly reduce the cost of a robotic mission by using cheaper, lower-reliability components and providing spares. This suggests that the

  4. Procedural pain management for neonates using nonpharmacological strategies: part 2: mother-driven interventions.

    Science.gov (United States)

    Campbell-Yeo, Marsha; Fernandes, Ananda; Johnston, Celeste

    2011-10-01

    This is the second of a 2-part series to provide an overview of our current level of knowledge related to nonpharmacological strategies to diminish the pain associated with commonly performed procedures in the NICU. In our first article we discussed the prevalence of repeated pain exposure in the NICU and the importance of nonpharmacological strategies specifically containment or facilitated tucking, swaddling, positioning, nonnutritive sucking, and sweet solutions. These strategies are generally nurse-driven and we believe their importance has been underutilized. In this article we will emphasize the importance of maternal presence as a mediator for pain relief. The efficacy of breastfeeding, maternal skin-to-skin care (often referred to as kangaroo care), and multisensorial stimulation such as auditory and olfactory recognition will be the primary focus of our discussion. In addition, although primarily mother-driven, these strategies are ultimately nurse-enabled, thus the importance of this connection cannot be under appreciated with respect to successful implementation in the NICU.

  5. Control of autonomous robot using neural networks

    Science.gov (United States)

    Barton, Adam; Volna, Eva

    2017-07-01

    The aim of the article is to design a method of control of an autonomous robot using artificial neural networks. The introductory part describes control issues from the perspective of autonomous robot navigation and the current mobile robots controlled by neural networks. The core of the article is the design of the controlling neural network, and generation and filtration of the training set using ART1 (Adaptive Resonance Theory). The outcome of the practical part is an assembled Lego Mindstorms EV3 robot solving the problem of avoiding obstacles in space. To verify models of an autonomous robot behavior, a set of experiments was created as well as evaluation criteria. The speed of each motor was adjusted by the controlling neural network with respect to the situation in which the robot was found.

  6. Robots show us how to teach them: feedback from robots shapes tutoring behavior during action learning.

    Science.gov (United States)

    Vollmer, Anna-Lisa; Mühlig, Manuel; Steil, Jochen J; Pitsch, Karola; Fritsch, Jannik; Rohlfing, Katharina J; Wrede, Britta

    2014-01-01

    Robot learning by imitation requires the detection of a tutor's action demonstration and its relevant parts. Current approaches implicitly assume a unidirectional transfer of knowledge from tutor to learner. The presented work challenges this predominant assumption based on an extensive user study with an autonomously interacting robot. We show that by providing feedback, a robot learner influences the human tutor's movement demonstrations in the process of action learning. We argue that the robot's feedback strongly shapes how tutors signal what is relevant to an action and thus advocate a paradigm shift in robot action learning research toward truly interactive systems learning in and benefiting from interaction.

  7. Faster-than-real-time robot simulation for plan development and robot safety

    International Nuclear Information System (INIS)

    Crane, C.D. III; Dalton, R.; Ogles, J.; Tulenko, J.S.; Zhou, X.

    1990-01-01

    The University of Florida, in cooperation with the Universities of Texas, Tennessee, and Michigan and Oak Ridge National Laboratory (ORNL), is developing an advanced robotic system for the US Department of Energy under the University Program for Robotics for Advanced Reactors. As part of this program, the University of Florida has been pursuing the development of a faster-than-real-time robotic simulation program for planning and control of mobile robotic operations to ensure the efficient and safe operation of mobile robots in nuclear power plants and other hazardous environments

  8. Soft Robotics Week

    CERN Document Server

    Rossiter, Jonathan; Iida, Fumiya; Cianchetti, Matteo; Margheri, Laura

    2017-01-01

    This book offers a comprehensive, timely snapshot of current research, technologies and applications of soft robotics. The different chapters, written by international experts across multiple fields of soft robotics, cover innovative systems and technologies for soft robot legged locomotion, soft robot manipulation, underwater soft robotics, biomimetic soft robotic platforms, plant-inspired soft robots, flying soft robots, soft robotics in surgery, as well as methods for their modeling and control. Based on the results of the second edition of the Soft Robotics Week, held on April 25 – 30, 2016, in Livorno, Italy, the book reports on the major research lines and novel technologies presented and discussed during the event.

  9. Rehabilitation robotics.

    Science.gov (United States)

    Krebs, H I; Volpe, B T

    2013-01-01

    This chapter focuses on rehabilitation robotics which can be used to augment the clinician's toolbox in order to deliver meaningful restorative therapy for an aging population, as well as on advances in orthotics to augment an individual's functional abilities beyond neurorestoration potential. The interest in rehabilitation robotics and orthotics is increasing steadily with marked growth in the last 10 years. This growth is understandable in view of the increased demand for caregivers and rehabilitation services escalating apace with the graying of the population. We provide an overview on improving function in people with a weak limb due to a neurological disorder who cannot properly control it to interact with the environment (orthotics); we then focus on tools to assist the clinician in promoting rehabilitation of an individual so that s/he can interact with the environment unassisted (rehabilitation robotics). We present a few clinical results occurring immediately poststroke as well as during the chronic phase that demonstrate superior gains for the upper extremity when employing rehabilitation robotics instead of usual care. These include the landmark VA-ROBOTICS multisite, randomized clinical study which demonstrates clinical gains for chronic stroke that go beyond usual care at no additional cost. Copyright © 2013 Elsevier B.V. All rights reserved.

  10. Medical robotics.

    Science.gov (United States)

    Ferrigno, Giancarlo; Baroni, Guido; Casolo, Federico; De Momi, Elena; Gini, Giuseppina; Matteucci, Matteo; Pedrocchi, Alessandra

    2011-01-01

    Information and communication technology (ICT) and mechatronics play a basic role in medical robotics and computer-aided therapy. In the last three decades, in fact, ICT technology has strongly entered the health-care field, bringing in new techniques to support therapy and rehabilitation. In this frame, medical robotics is an expansion of the service and professional robotics as well as other technologies, as surgical navigation has been introduced especially in minimally invasive surgery. Localization systems also provide treatments in radiotherapy and radiosurgery with high precision. Virtual or augmented reality plays a role for both surgical training and planning and for safe rehabilitation in the first stage of the recovery from neurological diseases. Also, in the chronic phase of motor diseases, robotics helps with special assistive devices and prostheses. Although, in the past, the actual need and advantage of navigation, localization, and robotics in surgery and therapy has been in doubt, today, the availability of better hardware (e.g., microrobots) and more sophisticated algorithms(e.g., machine learning and other cognitive approaches)has largely increased the field of applications of these technologies,making it more likely that, in the near future, their presence will be dramatically increased, taking advantage of the generational change of the end users and the increasing request of quality in health-care delivery and management.

  11. 9th International Robotic Sailing Conference

    CERN Document Server

    Cruz, Nuno

    2017-01-01

    This book contains selected papers that address a variety of topics related to the design, development and operation of unmanned and fully autonomous sailing boats. These papers were presented in the 9th International Robotic Sailing Conference, in association with the 9th World Robotic Sailing Championship that took place in Viana do Castelo, Portugal from the 5th to 10th of September 2016. The book is divided in three parts, each focusing on key aspects of robotic sailing. The first part addresses the design, construction and validation of autonomous sailboat platforms, including their rigs, appendages and control mechanisms. The second part is devoted to the development of sensors and algorithms to enhance the performance of robotic sailing boats, in terms of their speed, course control and manoeuvring ability. Finally, the papers in the last part are dedicated to the improvement of behaviours required for the accomplishment of complex autonomous missions. Robotic sailing is a relatively new multidisciplin...

  12. Robotics in near-earth space

    Science.gov (United States)

    Card, Michael E.

    1991-01-01

    The areas of space exploration in which robotic devices will play a part are identified, and progress to date in the space agency plans to acquire this capability is briefly reviewed. Roles and functions on orbit for robotic devices include well known activities, such as inspection and maintenance, assembly, docking, berthing, deployment, retrieval, materials handling, orbital replacement unit exchange, and repairs. Missions that could benefit from a robotic capability are discussed.

  13. System and method for controlling a vision guided robot assembly

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Yhu-Tin; Daro, Timothy; Abell, Jeffrey A.; Turner, III, Raymond D.; Casoli, Daniel J.

    2017-03-07

    A method includes the following steps: actuating a robotic arm to perform an action at a start position; moving the robotic arm from the start position toward a first position; determining from a vision process method if a first part from the first position will be ready to be subjected to a first action by the robotic arm once the robotic arm reaches the first position; commencing the execution of the visual processing method for determining the position deviation of the second part from the second position and the readiness of the second part to be subjected to a second action by the robotic arm once the robotic arm reaches the second position; and performing a first action on the first part using the robotic arm with the position deviation of the first part from the first position predetermined by the vision process method.

  14. Stimulation of Executive Functions as Part of the Language Intervention Process in Children with Autism Spectrum Disorder.

    Science.gov (United States)

    Sun, Ingrid Ya I; Varanda, Cristina Andrade; Fernandes, Fernanda Dreux

    2017-01-01

    Identifying effective methods for stimulating language and communication of children with autism spectrum disorder (ASD) is fundamental to the effective use of available resources to support these children. This pilot study was designed to explore the potential benefits of a program of stimulation of executive functions (SEF) on the functional aspects of language and communication through the assessment of the functional communicative profile and social-cognitive performance. Twenty children, aged 5-12 years, with a diagnosis of ASD participated in the study. Two stimulation programs were offered over a 10- to 12-week period as part of the regular services offered to these children through a University's speech and language therapy outpatient clinic in São Paulo, Brazil. Children either received SEF intervention in their home implemented by their parent/s, with close monitoring by the speech-language pathologist (SLP) (group 1), or they received SEF by the SLP during regular speech-language therapy individual sessions (group 2). The findings suggested that there were differences between the children's pre- and posttest performance. Significantly different performances were observed in the areas of occupation of communication space, proportion of communicative interactivity, and social-cognitive performance. The inclusion of activities to stimulate executive function abilities in language intervention for children with ASD warrants further investigation. © 2017 S. Karger AG, Basel.

  15. Generic robot architecture

    Science.gov (United States)

    Bruemmer, David J [Idaho Falls, ID; Few, Douglas A [Idaho Falls, ID

    2010-09-21

    The present invention provides methods, computer readable media, and apparatuses for a generic robot architecture providing a framework that is easily portable to a variety of robot platforms and is configured to provide hardware abstractions, abstractions for generic robot attributes, environment abstractions, and robot behaviors. The generic robot architecture includes a hardware abstraction level and a robot abstraction level. The hardware abstraction level is configured for developing hardware abstractions that define, monitor, and control hardware modules available on a robot platform. The robot abstraction level is configured for defining robot attributes and provides a software framework for building robot behaviors from the robot attributes. Each of the robot attributes includes hardware information from at least one hardware abstraction. In addition, each robot attribute is configured to substantially isolate the robot behaviors from the at least one hardware abstraction.

  16. 'Filigree Robotics'

    DEFF Research Database (Denmark)

    2016-01-01

    -scale 3D printed ceramics accompanied by prints, videos and ceramic probes, which introduce the material and design processes of the project.'Filigree Robotics' experiments with a combination of the traditional ceramic technique of ‘Overforming’ with 3d Laserscan and Robotic extrusion technique...... application of reflectivity after an initial 3d print. The consideration and integration of this material practice into a digital workflow took place in an interdisciplinary collaboration of Ceramicist Flemming Tvede Hansen from KADK Superformlab and architectural researchers from CITA (Martin Tamke, Henrik...... to the creation of the form and invites for experimentation. In Filigree Robotics we combine the crafting of the mold with a parallel running generative algorithm, which is fed by a constant laserscan of the 3d surface. This algorithm, analyses the topology of the mold, identifies high and low points and uses...

  17. Robotic and Survey Telescopes

    Science.gov (United States)

    Woźniak, Przemysław

    Robotic telescopes are revolutionizing the way astronomers collect their dataand conduct sky surveys. This chapter begins with a discussion of principles thatguide the process of designing, constructing, and operating telescopes andobservatories that offer a varying degree of automation, from instruments remotelycontrolled by observers to fully autonomous systems requiring no humansupervision during their normal operations. Emphasis is placed on designtrade-offs involved in building end-to-end systems intended for a wide range ofscience applications. The second part of the chapter contains descriptions ofseveral projects and instruments, both existing and currently under development.It is an attempt to provide a representative selection of actual systems thatillustrates state of the art in technology, as well as important ideas and milestonesin the development of the field. The list of presented instruments spans the fullrange in size starting from small all-sky monitors, through midrange robotic andsurvey telescopes, and finishing with large robotic instruments and surveys.Explosive growth of telescope networking is enabling entirely new modesof interaction between the survey and follow-up observing. Increasingimportance of standardized communication protocols and software is stressed.These developments are driven by the fusion of robotic telescope hardware,massive storage and databases, real-time knowledge extraction, and datacross-correlation on a global scale. The chapter concludes with examplesof major science results enabled by these new technologies and futureprospects.

  18. Cloud Robotics Platforms

    Directory of Open Access Journals (Sweden)

    Busra Koken

    2015-01-01

    Full Text Available Cloud robotics is a rapidly evolving field that allows robots to offload computation-intensive and storage-intensive jobs into the cloud. Robots are limited in terms of computational capacity, memory and storage. Cloud provides unlimited computation power, memory, storage and especially collaboration opportunity. Cloud-enabled robots are divided into two categories as standalone and networked robots. This article surveys cloud robotic platforms, standalone and networked robotic works such as grasping, simultaneous localization and mapping (SLAM and monitoring.

  19. Service Robots

    DEFF Research Database (Denmark)

    Clemmensen, Torkil; Nielsen, Jeppe Agger; Andersen, Kim Normann

    The position presented in this paper is that in order to understand how service robots shape, and are being shaped by, the physical and social contexts in which they are used, we need to consider both work/organizational analysis and interaction design. We illustrate this with qualitative data...... and personal experiences to generate discussion about how to link these two traditions. This paper presents selected results from a case study that investigated the implementation and use of robot vacuum cleaners in Danish eldercare. The study demonstrates interpretive flexibility with variation...

  20. Robot Choreography

    DEFF Research Database (Denmark)

    Jochum, Elizabeth Ann; Heath, Damith

    2016-01-01

    We propose a robust framework for combining performance paradigms with human robot interaction (HRI) research. Following an analysis of several case studies that combine the performing arts with HRI experiments, we propose a methodology and “best practices” for implementing choreography and other...... performance paradigms in HRI experiments. Case studies include experiments conducted in laboratory settings, “in the wild”, and live performance settings. We consider the technical and artistic challenges of designing and staging robots alongside humans in these various settings, and discuss how to combine...

  1. Cultural Robotics: The Culture of Robotics and Robotics in Culture

    Directory of Open Access Journals (Sweden)

    Hooman Samani

    2013-12-01

    Full Text Available In this paper, we have investigated the concept of “Cultural Robotics” with regard to the evolution of social into cultural robots in the 21st Century. By defining the concept of culture, the potential development of a culture between humans and robots is explored. Based on the cultural values of the robotics developers, and the learning ability of current robots, cultural attributes in this regard are in the process of being formed, which would define the new concept of cultural robotics. According to the importance of the embodiment of robots in the sense of presence, the influence of robots in communication culture is anticipated. The sustainability of robotics culture based on diversity for cultural communities for various acceptance modalities is explored in order to anticipate the creation of different attributes of culture between robots and humans in the future.

  2. Patient Evaluation and Preparation in Vascular and Interventional Radiology: What Every Interventional Radiologist Should Know (Part 1: Patient Assessment and Laboratory Tests)

    Energy Technology Data Exchange (ETDEWEB)

    Taslakian, Bedros, E-mail: btaslakian@gmail.com [NYU Langone Medical Center, Department of Radiology (United States); Sebaaly, Mikhael Georges, E-mail: ms246@aub.edu.lb; Al-Kutoubi, Aghiad, E-mail: mk00@aub.edu.lb [American University of Beirut Medical Center, Department of Diagnostic Radiology (Lebanon)

    2016-03-15

    Performing an interventional procedure imposes a commitment on interventional radiologists to conduct the initial patient assessment, determine the best course of therapy, and provide long-term care after the procedure is completed. After patient referral, contact with the referring physician and multidisciplinary team approach is vital. In addition, clinical history, physical examination, as well as full understanding of the pre-procedural laboratory results and imaging findings can guide the interventional radiologist to implement the most appropriate management plan, avoid unnecessary procedures, and prevent complications to achieve a successful outcome. We provide a comprehensive, methodical review of pre-procedural care and management in patients undergoing vascular and interventional radiology procedures.

  3. Patient Evaluation and Preparation in Vascular and Interventional Radiology: What Every Interventional Radiologist Should Know (Part 1: Patient Assessment and Laboratory Tests)

    International Nuclear Information System (INIS)

    Taslakian, Bedros; Sebaaly, Mikhael Georges; Al-Kutoubi, Aghiad

    2016-01-01

    Performing an interventional procedure imposes a commitment on interventional radiologists to conduct the initial patient assessment, determine the best course of therapy, and provide long-term care after the procedure is completed. After patient referral, contact with the referring physician and multidisciplinary team approach is vital. In addition, clinical history, physical examination, as well as full understanding of the pre-procedural laboratory results and imaging findings can guide the interventional radiologist to implement the most appropriate management plan, avoid unnecessary procedures, and prevent complications to achieve a successful outcome. We provide a comprehensive, methodical review of pre-procedural care and management in patients undergoing vascular and interventional radiology procedures

  4. Self-management interventions for skin care in people with a spinal cord injury: part 2-a systematic review of use of theory and quality of intervention reporting.

    Science.gov (United States)

    Baron, Justine S; Sullivan, Katrina J; Swaine, Jillian M; Aspinall, Arlene; Jaglal, Susan; Presseau, Justin; Wolfe, Dalton; Grimshaw, Jeremy M

    2018-05-25

    Systematic review. To examine use of theory and quality of reporting in skin care self-management interventions for people with SCI. International. The Theory Coding Scheme (TCS) and the Template for Intervention Description and Replication (TIDieR) checklist were applied by two independent researchers to 17 interventions identified in a systematic review of self-management interventions for skin care in people with SCI. Six (35%) of the 17 interventions reviewed were reported to have a theoretical basis. Theories used included three of the most commonly featured in health behavior research (the Health Belief Model, Social Cognitive Theory, and the Transtheoretical Model). In these six interventions, theory was used to design content but not to select participants or tailor strategies. None of the interventions were used to test theories in the SCI population, or to propose theoretical refinements. Reporting quality was found to vary by TIDieR item, with 6-100% of interventions including recommended information. Information on two intervention fidelity items was missing in 53 and 82% of descriptions. Use of theory and reporting quality in SCI self-management research remains suboptimal, potentially slowing down advancements in this area of research. Rehabilitation researchers should direct their efforts toward improving these practices to help build a science of SCI self-management that is cumulative and reproducible by clinicians, scientists, and policy makers. This work was funded through a postdoctoral fellowship awarded to the first author by the Rick Hansen Institute.

  5. Robot vision for nuclear advanced robot

    International Nuclear Information System (INIS)

    Nakayama, Ryoichi; Okano, Hideharu; Kuno, Yoshinori; Miyazawa, Tatsuo; Shimada, Hideo; Okada, Satoshi; Kawamura, Astuo

    1991-01-01

    This paper describes Robot Vision and Operation System for Nuclear Advanced Robot. This Robot Vision consists of robot position detection, obstacle detection and object recognition. With these vision techniques, a mobile robot can make a path and move autonomously along the planned path. The authors implemented the above robot vision system on the 'Advanced Robot for Nuclear Power Plant' and tested in an environment mocked up as nuclear power plant facilities. Since the operation system for this robot consists of operator's console and a large stereo monitor, this system can be easily operated by one person. Experimental tests were made using the Advanced Robot (nuclear robot). Results indicate that the proposed operation system is very useful, and can be operate by only person. (author)

  6. Robotic Surgery

    Science.gov (United States)

    Childress, Vincent W.

    2007-01-01

    The medical field has many uses for automated and remote-controlled technology. For example, if a tissue sample is only handled in the laboratory by a robotic handling system, then it will never come into contact with a human. Such a system not only helps to automate the medical testing process, but it also helps to reduce the chances of…

  7. Multiprocessor development for robot control

    International Nuclear Information System (INIS)

    Lee, John Min; Kim, Seung Ho; Kim, Chang Hoi; Kim, Byung Soo; Hwang, Suk Yeong; Lee, Young Bum; Sohn, Suk Won; Kim, Woon Gi

    1990-01-01

    The project of this study is to develop a real time controller applying autonomous robotic systems operated in hostile environment. Developed control system is designed with a multiprocessor to get independency and reliability as well as to extend the system easily. The control system is designed in three distinct subsystems (supervisory control part, functional control part, and remote control part). To review the functional performance of developed controller, a prototype mobile robot, which was installed 4 DOF mainpulator, was designed and manufactured. Initial tests showed that the robot could turn with a radius of 38 cm and a maximum speed of 1.26 km/hr and go over obstacle of 18 cm in height. (author)

  8. Accuracy and feasibility of frameless stereotactic and robot-assisted CT-based puncture in interventional radiology. A comparative phantom study

    International Nuclear Information System (INIS)

    Stoffner, R.; Widmann, G.; Bale, R.; Augschoell, C.; Boehler, D.

    2009-01-01

    Purpose: To compare the accuracy of frameless stereotactic and robot-assisted puncture in vitro based on computed tomography (CT) imaging with a slice thickness of 1, 3, and 5 mm. Materials and Methods: 300 punctures were carried out with help of the Atlas aiming device guided by the optical navigation system Stealth Station TREONplus and 150 punctures were guided by the robotic assistance system Innomotion. Conically shaped rods were punctured with Kirschner wires. The accuracy was evaluated on the basis of control CTs by measuring the Euclidean distance between the wire tip and target and the normal distance between the target and wire. Results: With the Stealth Station a mean Euclidean distance of 1.94±0.912, 2.2±1.136, and 2.74±1.166 mm at a slice thickness of 1, 3 and 5 mm, respectively, was reached. The mean normal distance was 1.64±0.919, 1.84±1.189, and 2.48±1.196 mm, respectively. The Innomotion system resulted in a mean Euclidean distance of 1.69±0.772, 1.91±0.673, and 2.30±0.881 mm, respectively, while the mean normal distance was (1.42±0.78), 1.60±0.733, and 1.98±1.002 mm, respectively. A statistical significance between accuracies with both systems with 1 mm and 3 mm slices could not be detected (p > 0.05). At a slice thickness of 5 mm, the robot was significantly more accurate, but not as accurate as when using thinner slices (p < 0.05). The procedure time is longer for the Innomotion system (∝30 vs. ∝18 min), and the practicability is higher with the Stealth Station. (orig.)

  9. Laws on Robots, Laws by Robots, Laws in Robots : Regulating Robot Behaviour by Design

    NARCIS (Netherlands)

    Leenes, R.E.; Lucivero, F.

    2015-01-01

    Speculation about robot morality is almost as old as the concept of a robot itself. Asimov’s three laws of robotics provide an early and well-discussed example of moral rules robots should observe. Despite the widespread influence of the three laws of robotics and their role in shaping visions of

  10. Cooperative robots and sensor networks 2015

    CERN Document Server

    Dios, JRamiro

    2015-01-01

    This book compiles some of the latest research in cooperation between robots and sensor networks. Structured in twelve chapters, this book addresses fundamental, theoretical, implementation and experimentation issues. The chapters are organized into four parts namely multi-robots systems, data fusion and localization, security and dependability, and mobility.

  11. Robotics Team Lights Up New Year's Eve

    Science.gov (United States)

    LeBlanc, Cheryl

    2011-01-01

    A robotics team from Muncie, Indiana--the PhyXTGears--is made up of high school students from throughout Delaware County. The group formed as part of the FIRST Robotics program (For Inspiration and Recognition of Science and Technology), an international program founded by inventor Dean Kamen in which students work with professional engineers and…

  12. How industry can help us fight against botnets : Notes on regulating private-sector intervention

    NARCIS (Netherlands)

    E Silva, Karine

    2016-01-01

    Could industry improve our response to botnet attacks? If so, how should this private sector participation be regulated? This paper examines how regulation could be used to facilitate private sector intervention against robot networks, also known as botnets. The first part of this paper is dedicated

  13. Association of a full-day vs part-day preschool intervention with school readiness, attendance, and parent involvement.

    Science.gov (United States)

    Reynolds, Arthur J; Richardson, Brandt A; Hayakawa, Momoko; Lease, Erin M; Warner-Richter, Mallory; Englund, Michelle M; Ou, Suh-Ruu; Sullivan, Molly

    2014-11-26

    Early childhood interventions have demonstrated positive effects on well-being. Whether full-day vs part-day attendance improves outcomes is unknown. To evaluate the association between a full- vs part-day early childhood program and school readiness, attendance, and parent involvement. End-of-preschool follow-up of a nonrandomized, matched-group cohort of predominantly low-income, ethnic minority children enrolled in the Child-Parent Centers (CPC) for the full day (7 hours; n = 409) or part day (3 hours on average; n = 573) in the 2012-2013 school year in 11 schools in Chicago, Illinois. The Midwest CPC Education Program provides comprehensive instruction, family-support, and health services from preschool to third grade. School readiness skills at the end of preschool, attendance and chronic absences, and parental involvement. The readiness domains in the Teaching Strategies GOLD Assessment System include a total of 49 items with a score range of 105-418. The specific domains are socioemotional with 9 items (score range, 20-81), language with 6 items (score range, 15-54), literacy with 12 items (score range, 9-104), math with 7 items (score, 8-60), physical health with 5 items (score range, 14-45), and cognitive development with 10 items (score range, 18-90). Full-day preschool participants had higher scores than part-day peers on socioemotional development (58.6 vs 54.5; difference, 4.1; 95% CI, 0.5-7.6; P = .03), language (39.9 vs 37.3; difference, 2.6; 95% CI, 0.6-4.6; P = .01), math (40.0 vs 36.4; difference, 3.6; 95% CI, 0.5-6.7; P = .02), physical health (35.5 vs 33.6; difference, 1.9; 95% CI, 0.5-3.2; P = .006), and the total score (298.1 vs 278.2; difference, 19.9; 95% CI, 1.2-38.4; P = .04). Literacy (64.5 vs 58.6; difference, 5.9; 95% CI, -0.07 to 12.4; P = .08) and cognitive development (59.7 vs 57.7; difference, 2.0; 95% CI, -2.4 to 6.3; P = .38) were not significant. Full-day preschool graduates also had higher

  14. Powered mobility intervention: understanding the position of tool use learning as part of implementing the ALP tool.

    Science.gov (United States)

    Nilsson, Lisbeth; Durkin, Josephine

    2017-10-01

    To explore the knowledge necessary for adoption and implementation of the Assessment of Learning Powered mobility use (ALP) tool in different practice settings for both adults and children. To consult with a diverse population of professionals working with adults and children, in different countries and various settings; who were learning about or using the ALP tool, as part of exploring and implementing research findings. Classical grounded theory with a rigorous comparative analysis of data from informants together with reflections on our own rich experiences of powered mobility practice and comparisons with the literature. A core category learning tool use and a new theory of cognizing tool use, with its interdependent properties: motivation, confidence, permissiveness, attentiveness and co-construction has emerged which explains in greater depth what enables the application of the ALP tool. The scientific knowledge base on tool use learning and the new theory conveys the information necessary for practitioner's cognizing how to apply the learning approach of the ALP tool in order to enable tool use learning through powered mobility practice as a therapeutic intervention in its own right. This opens up the possibility for more children and adults to have access to learning through powered mobility practice. Implications for rehabilitation Tool use learning through powered mobility practice is a therapeutic intervention in its own right. Powered mobility practice can be used as a rehabilitation tool with individuals who may not need to become powered wheelchair users. Motivation, confidence, permissiveness, attentiveness and co-construction are key properties for enabling the application of the learning approach of the ALP tool. Labelling and the use of language, together with honing observational skills through viewing video footage, are key to developing successful learning partnerships.

  15. Predictors of receiving therapy among very low birth weight 2-year olds eligible for Part C early intervention in Wisconsin.

    Science.gov (United States)

    McManus, Beth Marie; Robert, Stephanie; Albanese, Aggie; Sadek-Badawi, Mona; Palta, Mari

    2013-07-11

    The Individuals with Disabilities Education Act (Part C) authorizes states to establish systems to provide early intervention services (e.g., therapy) for children at risk, with the incentive of federal financial support. This study examines family and neighborhood characteristics associated with currently utilizing physical, occupational, or speech therapy among very low birthweight (VLBW) 2-year-old children who meet Wisconsin eligibility requirements for early intervention services (EI) due to developmental delay. This cross-sectional analysis used data from the Newborn Lung Project, a regional cohort study of VLBW infants hospitalized in Wisconsin's newborn intensive care units during 2003-2004. We included the 176 children who were age two at follow-up, and met Wisconsin state eligibility requirements for EI based on developmental delay. Exact logistic regression was used to describe child and neighborhood socio-demographic correlates of parent-reported receipt of therapy. Among VLBW children with developmental delay, currently utilizing therapy was higher among children with Medicaid (aOR = 5.3, 95% CI: 1.3, 28.3) and concomitant developmental disability (aOR = 5.2, 95% CI: 2.1, 13.3) and lower for those living in a socially more disadvantaged neighborhood (aOR=0.48, 95% CI: 0.21, 0.98, per tertile). Among a sample of VLBW 2-year olds with developmental delays who are EI-eligible in WI, 4 out of 5 were currently receiving therapy, per parent report. Participation in Medicaid positively influences therapy utilization. Children with developmental difficulties who live in socially disadvantaged neighborhoods are at highest risk for not receiving therapy.

  16. Towards a Location-based Service for Early Mental Health Interventions in Disaster Response Using Minimalistic Tele-operated Android Robots Technology

    Science.gov (United States)

    Vahidi, H.; Mobasheri, A.; Alimardani, M.; Guan, Q.; Bakillah, M.

    2014-04-01

    Providing early mental health services during disaster is a great challenge in the disaster response phase. Lack of access to adequate mental-health professionals in the early stages of large-scale disasters dramatically influences the trend of a successful mental health aid. In this paper, a conceptual framework has been suggested for adopting cellphone-type tele-operated android robots in the early stages of disasters for providing the early mental health services for disaster survivors by developing a locationbased and participatory approach. The techniques of enabling GI-services in a Peer-to-Peer (P2P) environment were studied to overcome the limitations of current centralized services. Therefore, the aim of this research study is to add more flexibility and autonomy to GI web services (WMS, WFS, WPS, etc.) and alleviate to some degree the inherent limitations of these centralized systems. A P2P system Architecture is presented for the location-based service using minimalistic tele-operated android robots, and some key techniques of implementing this service using BestPeer were studied for developing this framework.

  17. Brain-state dependent robotic reaching movement with a multi-joint arm exoskeleton: combining brain-machine interfacing and robotic rehabilitation

    Directory of Open Access Journals (Sweden)

    Daniel eBrauchle

    2015-10-01

    Full Text Available While robot-assisted arm and hand training after stroke allows for intensive task-oriented practice, it has provided only limited additional benefit over dose-matched physiotherapy up to now. These rehabilitation devices are possibly too supportive during the exercises. Neurophysiological signals might be one way of avoiding slacking and providing robotic support only when the brain is particularly responsive to peripheral input.We tested the feasibility of three-dimensional robotic assistance for reach-to-grasp movements with a multi-joint exoskeleton during motor imagery-related desynchronization of sensorimotor oscillations in the β-band only. We also registered task-related network changes of cortical functional connectivity by electroencephalography via the imaginary part of the coherence function.Healthy subjects and stroke survivors showed similar patterns – but different aptitudes – of controlling the robotic movement. All participants in this pilot study with nine healthy subjects and two stroke patients achieved their maximum performance during the early stages of the task. Robotic control was significantly higher and less variable when proprioceptive feedback was provided in addition to visual feedback, i.e. when the orthosis was actually attached to the subject’s arm during the task. A distributed cortical network of task-related coherent activity in the θ-band showed significant differences between healthy subjects and stroke patients as well as between early and late periods of the task.Brain-robot interfaces may successfully link three-dimensional robotic training to the participants’ efforts and allow for task-oriented practice of activities of daily living with a physiologically controlled multi-joint exoskeleton. Changes of cortical physiology during the task might also help to make subject-specific adjustments of task difficulty and guide adjunct interventions to facilitate motor learning for functional restoration.

  18. Micro Robotics Lab

    Data.gov (United States)

    Federal Laboratory Consortium — Our research is focused on the challenges of engineering robotic systems down to sub-millimeter size scales. We work both on small mobile robots (robotic insects for...

  19. Robots of the Future

    Indian Academy of Sciences (India)

    two main types of robots: industrial robots, and autonomous robots. .... position); it also has a virtual CPU with two stacks and three registers that hold 32-bit strings. Each item ..... just like we can aggregate images, text, and information from.

  20. Presentation robot Advee

    Czech Academy of Sciences Publication Activity Database

    Krejsa, Jiří; Věchet, Stanislav; Hrbáček, J.; Ripel, T.; Ondroušek, V.; Hrbáček, R.; Schreiber, P.

    2012-01-01

    Roč. 18, 5/6 (2012), s. 307-322 ISSN 1802-1484 Institutional research plan: CEZ:AV0Z20760514 Keywords : mobile robot * human - robot interface * localization Subject RIV: JD - Computer Applications, Robot ics

  1. Towards Sociable Robots

    DEFF Research Database (Denmark)

    Ngo, Trung Dung

    This thesis studies aspects of self-sufficient energy (energy autonomy) for truly autonomous robots and towards sociable robots. Over sixty years of history of robotics through three developmental ages containing single robot, multi-robot systems, and social (sociable) robots, the main objective...... of roboticists mostly focuses on how to make a robotic system function autonomously and further, socially. However, such approaches mostly emphasize behavioural autonomy, rather than energy autonomy which is the key factor for not only any living machine, but for life on the earth. Consequently, self......-sufficient energy is one of the challenges for not only single robot or multi-robot systems, but also social and sociable robots. This thesis is to deal with energy autonomy for multi-robot systems through energy sharing (trophallaxis) in which each robot is equipped with two capabilities: self-refueling energy...

  2. Cloud Robotics Model

    OpenAIRE

    Mester, Gyula

    2015-01-01

    Cloud Robotics was born from the merger of service robotics and cloud technologies. It allows robots to benefit from the powerful computational, storage, and communications resources of modern data centres. Cloud robotics allows robots to take advantage of the rapid increase in data transfer rates to offload tasks without hard real time requirements. Cloud Robotics has rapidly gained momentum with initiatives by companies such as Google, Willow Garage and Gostai as well as more than a dozen a...

  3. Robot operating system (ROS) the complete reference

    CERN Document Server

    The objective of this book is to provide the reader with a comprehensive coverage on the Robot Operating Systems (ROS) and latest related systems, which is currently considered as the main development framework for robotics applications. The book includes twenty-seven chapters organized into eight parts. Part 1 presents the basics and foundations of ROS. In Part 2, four chapters deal with navigation, motion and planning. Part 3 provides four examples of service and experimental robots. Part 4 deals with real-world deployment of applications. Part 5 presents signal-processing tools for perception and sensing. Part 6 provides software engineering methodologies to design complex software with ROS. Simulations frameworks are presented in Part 7. Finally, Part 8 presents advanced tools and frameworks for ROS including multi-master extension, network introspection, controllers and cognitive systems. This book will be a valuable companion for ROS users and developers to learn more ROS capabilities and features.   ...

  4. Cooperative robots and sensor networks 2014

    CERN Document Server

    Khelil, Abdelmajid

    2014-01-01

    This book is the second volume on Cooperative Robots and Sensor Networks. The primary objective of this book is to provide an up-to-date reference for cutting-edge studies and research trends related to mobile robots and wireless sensor networks, and in particular for the coupling between them. Indeed, mobile robots and wireless sensor networks have enabled great potentials and a large space for ubiquitous and pervasive applications. Robotics and wireless sensor networks have mostly been considered as separate research fields and little work has investigated the marriage between these two technologies. However, these two technologies share several features, enable common cyber-physical applications and provide complementary support to each other. The book consists of ten chapters, organized into four parts. The first part of the book presents three chapters related to localization of mobile robots using wireless sensor networks. Two chapters presented new solutions based Extended Kalman Filter and Particle Fi...

  5. Robot Programming.

    Science.gov (United States)

    1982-12-01

    Paris, France, June, 1982, 519-530. Latoinbe, J. C. "Equipe Intelligence Artificielle et Robotique: Etat d’avancement des recherches," Laboratoire...8217AD-A127 233 ROBOT PROGRRMMING(U) MASSACHUSETTS INST OFGTECHi/ CAMBRIDGE ARTIFICIAL INTELLIGENCE LAB T LOZANO-PEREZ UNCLASSIFIED DC8 AI-9 N884...NAME AND ADDRESS 10. PROGRAM ELEMENT. PROJECT. TASK Artificial Intelligence Laboratory AREA I WORK UNIT NUMBERS ,. 545 Technology Square Cambridge

  6. Friendly network robotics; Friendly network robotics

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This paper summarizes the research results on the friendly network robotics in fiscal 1996. This research assumes an android robot as an ultimate robot and the future robot system utilizing computer network technology. The robot aiming at human daily work activities in factories or under extreme environments is required to work under usual human work environments. The human robot with similar size, shape and functions to human being is desirable. Such robot having a head with two eyes, two ears and mouth can hold a conversation with human being, can walk with two legs by autonomous adaptive control, and has a behavior intelligence. Remote operation of such robot is also possible through high-speed computer network. As a key technology to use this robot under coexistence with human being, establishment of human coexistent robotics was studied. As network based robotics, use of robots connected with computer networks was also studied. In addition, the R-cube (R{sup 3}) plan (realtime remote control robot technology) was proposed. 82 refs., 86 figs., 12 tabs.

  7. Cultural Robotics: The Culture of Robotics and Robotics in Culture

    OpenAIRE

    Hooman Samani; Elham Saadatian; Natalie Pang; Doros Polydorou; Owen Noel Newton Fernando; Ryohei Nakatsu; Jeffrey Tzu Kwan Valino Koh

    2013-01-01

    In this paper, we have investigated the concept of “Cultural Robotics” with regard to the evolution of social into cultural robots in the 21st Century. By defining the concept of culture, the potential development of a culture between humans and robots is explored. Based on the cultural values of the robotics developers, and the learning ability of current robots, cultural attributes in this regard are in the process of being formed, which would define the new concept of cultural robotics. Ac...

  8. Research on the inspection robot for cable tunnel

    Science.gov (United States)

    Xin, Shihao

    2017-03-01

    Robot by mechanical obstacle, double end communication, remote control and monitoring software components. The mechanical obstacle part mainly uses the tracked mobile robot mechanism, in order to facilitate the design and installation of the robot, the other auxiliary swing arm; double side communication part used a combination of communication wire communication with wireless communication, great improve the communication range of the robot. When the robot is controlled by far detection range, using wired communication control, on the other hand, using wireless communication; remote control part mainly completes the inspection robot walking, navigation, positioning and identification of cloud platform control. In order to improve the reliability of its operation, the preliminary selection of IPC as the control core the movable body selection program hierarchical structure as a design basis; monitoring software part is the core part of the robot, which has a definite diagnosis Can be instead of manual simple fault judgment, instead the robot as a remote actuators, staff as long as the remote control can be, do not have to body at the scene. Four parts are independent of each other but are related to each other, the realization of the structure of independence and coherence, easy maintenance and coordination work. Robot with real-time positioning function and remote control function, greatly improves the IT operation. Robot remote monitor, to avoid the direct contact with the staff and line, thereby reducing the accident casualties, for the safety of the inspection work has far-reaching significance.

  9. Hand Rehabilitation Robotics on Poststroke Motor Recovery

    Science.gov (United States)

    2017-01-01

    The recovery of hand function is one of the most challenging topics in stroke rehabilitation. Although the robot-assisted therapy has got some good results in the latest decades, the development of hand rehabilitation robotics is left behind. Existing reviews of hand rehabilitation robotics focus either on the mechanical design on designers' view or on the training paradigms on the clinicians' view, while these two parts are interconnected and both important for designers and clinicians. In this review, we explore the current literature surrounding hand rehabilitation robots, to help designers make better choices among varied components and thus promoting the application of hand rehabilitation robots. An overview of hand rehabilitation robotics is provided in this paper firstly, to give a general view of the relationship between subjects, rehabilitation theories, hand rehabilitation robots, and its evaluation. Secondly, the state of the art hand rehabilitation robotics is introduced in detail according to the classification of the hardware system and the training paradigm. As a result, the discussion gives available arguments behind the classification and comprehensive overview of hand rehabilitation robotics. PMID:29230081

  10. Post-procedural Care in Interventional Radiology: What Every Interventional Radiologist Should Know—Part I: Standard Post-procedural Instructions and Follow-Up Care

    Energy Technology Data Exchange (ETDEWEB)

    Taslakian, Bedros, E-mail: Bedros.Taslakian@nyumc.org; Sridhar, Divya [NYU Langone Medical Center, Department of Radiology, Interventional Radiology Section (United States)

    2017-04-15

    Interventional radiology (IR) has evolved into a full-fledged clinical specialty with attendant patient care responsibilities. Success in IR now requires development of a full clinical practice, including consultations, inpatient admitting privileges, and an outpatient clinic. In addition to technical excellence and innovation, maintaining a comprehensive practice is imperative for interventional radiologists to compete successfully for patients and referral bases. A structured approach to periprocedural care, including routine follow-up and early identification and management of complications, facilitates efficient and thorough management with an emphasis on quality and patient safety.

  11. Some Qualitative Requirements for Testing of Nuclear Emergency Response Robots

    International Nuclear Information System (INIS)

    Eom, Heungseop; Cho, Jai Wan; Choi, Youngsoo; Jeong, Kyungmin

    2014-01-01

    Korea Atomic Energy Research Institute (KAERI) is carrying out the project 'Development of Core Technology for Remote Response in Nuclear Emergency Situation', and as a part of the project, we are studying the reliability and performance requirements of nuclear emergency response robots. In this paper, we described some qualitative requirements for testing of nuclear emergency response robots which are different to general emergency response robots. We briefly introduced test requirements of general emergency response robots and described some qualitative aspects of test requirements for nuclear emergency response robots. When considering an immature field-robot technology and variety of nuclear emergency situations, it seems hard to establish quantitative test requirements of these robots at this time. However, based on studies of nuclear severe accidents and the experience of Fukushima NPP accident, we can expect some test requirements including quantitative ones for nuclear emergency response robots

  12. Research and Evaluations of the Health Aspects of Disasters, Part VI: Interventional Research and the Disaster Logic Model.

    Science.gov (United States)

    Birnbaum, Marvin L; Daily, Elaine K; O'Rourke, Ann P; Kushner, Jennifer

    2016-04-01

    Disaster-related interventions are actions or responses undertaken during any phase of a disaster to change the current status of an affected community or a Societal System. Interventional disaster research aims to evaluate the results of such interventions in order to develop standards and best practices in Disaster Health that can be applied to disaster risk reduction. Considering interventions as production functions (transformation processes) structures the analyses and cataloguing of interventions/responses that are implemented prior to, during, or following a disaster or other emergency. Since currently it is not possible to do randomized, controlled studies of disasters, in order to validate the derived standards and best practices, the results of the studies must be compared and synthesized with results from other studies (ie, systematic reviews). Such reviews will be facilitated by the selected studies being structured using accepted frameworks. A logic model is a graphic representation of the transformation processes of a program [project] that shows the intended relationships between investments and results. Logic models are used to describe a program and its theory of change, and they provide a method for the analyzing and evaluating interventions. The Disaster Logic Model (DLM) is an adaptation of a logic model used for the evaluation of educational programs and provides the structure required for the analysis of disaster-related interventions. It incorporates a(n): definition of the current functional status of a community or Societal System, identification of needs, definition of goals, selection of objectives, implementation of the intervention(s), and evaluation of the effects, outcomes, costs, and impacts of the interventions. It is useful for determining the value of an intervention and it also provides the structure for analyzing the processes used in providing the intervention according to the Relief/Recovery and Risk-Reduction Frameworks.

  13. HYBRID COMMUNICATION NETWORK OF MOBILE ROBOT AND QUAD-COPTER

    Directory of Open Access Journals (Sweden)

    Moustafa M. Kurdi

    2017-01-01

    Full Text Available This paper introduces the design and development of QMRS (Quadcopter Mobile Robotic System. QMRS is a real-time obstacle avoidance capability in Belarus-132N mobile robot with the cooperation of quadcopter Phantom-4. The function of QMRS consists of GPS used by Mobile Robot and image vision and image processing system from both robot and quad-copter and by using effective searching algorithm embedded inside the robot. Having the capacity to navigate accurately is one of the major abilities of a mobile robot to effectively execute a variety of jobs including manipulation, docking, and transportation. To achieve the desired navigation accuracy, mobile robots are typically equipped with on-board sensors to observe persistent features in the environment, to estimate their pose from these observations, and to adjust their motion accordingly. Quadcopter takes off from Mobile Robot, surveys the terrain and transmits the processed Image terrestrial robot. The main objective of research paper is to focus on the full coordination between robot and quadcopter by designing an efficient wireless communication using WIFI. In addition, it identify the method involving the use of vision and image processing system from both robot and quadcopter; analyzing path in real-time and avoiding obstacles based-on the computational algorithm embedded inside the robot. QMRS increases the efficiency and reliability of the whole system especially in robot navigation, image processing and obstacle avoidance due to the help and connection among the different parts of the system.

  14. Adaptive heterogeneous multi-robot teams

    Energy Technology Data Exchange (ETDEWEB)

    Parker, L.E.

    1998-11-01

    This research addresses the problem of achieving fault tolerant cooperation within small- to medium-sized teams of heterogeneous mobile robots. The author describes a novel behavior-based, fully distributed architecture, called ALLIANCE, that utilizes adaptive action selection to achieve fault tolerant cooperative control in robot missions involving loosely coupled, largely independent tasks. The robots in this architecture possess a variety of high-level functions that they can perform during a mission, and must at all times select an appropriate action based on the requirements of the mission, the activities of other robots, the current environmental conditions, and their own internal states. Since such cooperative teams often work in dynamic and unpredictable environments, the software architecture allows the team members to respond robustly and reliably to unexpected environmental changes and modifications in the robot team that may occur due to mechanical failure, the learning of new skills, or the addition or removal of robots from the team by human intervention. After presenting ALLIANCE, the author describes in detail the experimental results of an implementation of this architecture on a team of physical mobile robots performing a cooperative box pushing demonstration. These experiments illustrate the ability of ALLIANCE to achieve adaptive, fault-tolerant cooperative control amidst dynamic changes in the capabilities of the robot team.

  15. The Robots for Nuclear Power Plants

    International Nuclear Information System (INIS)

    Choi, Chang Hwan; Kim, Seung Ho; Kim, Chang Hoi; Seo, Yong Chil; Shin, Ho Cheol; Lee, Sung Uk; Jung, Kyung Min; Jung, Seung Ho; Choi, Young So

    2005-01-01

    Nuclear energy becomes a major energy source worldwide even though the debating environmental and safety dispute. In order to cope with the issues related to the nuclear power plant, the uncertain human factors need to be minimized by automating the inspection and maintenance work done by human workers. The demands of robotic system in nuclear industry have been growing to ensure the safety of nuclear facilities, to detect early unusual condition of it through an inspection, to protect the human workers from irradiation, and to maintain it efficiently. NRL (Nuclear Robotics Laboratory) in KAERI has been developing robotic systems to inspect and maintain nuclear power plants in stead of human workers for over thirteen years. In order to carry out useful tasks, a nuclear robot generally requires the followings. First, the robot should be protected against radiation. Second, a mobile system is required to access to the work place. Third, a kind of manipulator is required to complete the tasks such as handling radioactive wastes and other contaminated objects, etc. Fourth, a sensing system such as cameras, ultrasonic sensors, temperature sensors, dosimetry equipments etc., are required for operators to observe the work place. Lastly, a control system to help the operators control the robots. The control system generally consists of a supervisory control part and remote control part. The supervisory control part consists of a man-machine interface such as 3D graphics and a joystick. The remote control part manages the robot so that it follow the operator's command

  16. Calibration of Robot Reference Frames for Enhanced Robot Positioning Accuracy

    OpenAIRE

    Cheng, Frank Shaopeng

    2008-01-01

    This chapter discussed the importance and methods of conducting robot workcell calibration for enhancing the accuracy of the robot TCP positions in industrial robot applications. It shows that the robot frame transformations define the robot geometric parameters such as joint position variables, link dimensions, and joint offsets in an industrial robot system. The D-H representation allows the robot designer to model the robot motion geometry with the four standard D-H parameters. The robot k...

  17. Welding robot package; Arc yosetsu robot package

    Energy Technology Data Exchange (ETDEWEB)

    Nishikawa, S. [Yaskawa Electric Corp., Kitakyushu (Japan)

    1998-09-01

    For the conventional high-speed welding robot, the welding current was controlled mainly for reducing the spatters during short circuits and for stabilizing the beads by the periodic short circuits. However, an increase of deposition amount in response to the speed is required for the high-speed welding. Large-current low-spatter welding current region control was added. Units were integrated into a package by which the arc length is kept in short without dispersion of arc length for welding without defects such as undercut and unequal beads. In automobile industry, use of aluminum parts is extended for the light weight. The welding is very difficult, and automation is not so progressing in spite of the poor environment. Buckling of welding wire is easy to occur, and supply of wire is obstructed by the deposition of chipped powders on the torch cable, which stay within the contact chip resulting in the deposition. Dislocation of locus is easy to occur at the corner of rectangular pipe during the welding. By improving these troubles, an aluminum MIG welding robot package has been developed. 13 figs.

  18. Systematic Review of Occupational Therapy and Adult Cancer Rehabilitation: Part 2. Impact of Multidisciplinary Rehabilitation and Psychosocial, Sexuality, and Return-to-Work Interventions.

    Science.gov (United States)

    Hunter, Elizabeth G; Gibson, Robert W; Arbesman, Marian; D'Amico, Mariana

    This article is the second part of a systematic review of evidence for the effectiveness of cancer rehabilitation interventions within the scope of occupational therapy that address the activity and participation needs of adult cancer survivors. This article focuses on the use of multidisciplinary rehabilitation and interventions that address psychosocial outcomes, sexuality, and return to work. Strong evidence indicates that multidisciplinary rehabilitation benefits cancer survivors and that psychosocial strategies can reduce anxiety and depression. Moderate evidence indicates that interventions can support survivors in returning to the level of sexuality desired and help with return to work. Part 1 of the review also appears in this issue. Copyright © 2017 by the American Occupational Therapy Association, Inc.

  19. Soft Dielectric Elastomer Oscillators Driving Bioinspired Robots.

    Science.gov (United States)

    Henke, E-F Markus; Schlatter, Samuel; Anderson, Iain A

    2017-12-01

    Entirely soft robots with animal-like behavior and integrated artificial nervous systems will open up totally new perspectives and applications. To produce them, we must integrate control and actuation in the same soft structure. Soft actuators (e.g., pneumatic and hydraulic) exist but electronics are hard and stiff and remotely located. We present novel soft, electronics-free dielectric elastomer oscillators, which are able to drive bioinspired robots. As a demonstrator, we present a robot that mimics the crawling motion of the caterpillar, with an integrated artificial nervous system, soft actuators and without any conventional stiff electronic parts. Supplied with an external DC voltage, the robot autonomously generates all signals that are necessary to drive its dielectric elastomer actuators, and it translates an in-plane electromechanical oscillation into a crawling locomotion movement. Therefore, all functional and supporting parts are made of polymer materials and carbon. Besides the basic design of this first electronic-free, biomimetic robot, we present prospects to control the general behavior of such robots. The absence of conventional stiff electronics and the exclusive use of polymeric materials will provide a large step toward real animal-like robots, compliant human machine interfaces, and a new class of distributed, neuron-like internal control for robotic systems.

  20. Design and Implementation of a New DELTA Parallel Robot in Robotics Competitions

    Directory of Open Access Journals (Sweden)

    Jonqlan Lin

    2015-10-01

    Full Text Available This investigation concerns the design and implementation of the DELTA parallel robot, covering the entire mechatronic process, involving kinematics, control design and optimizing methods. To accelerate the construction of the robot, 3D printing is used to fabricate end-effector parts. The parts are modular, low-cost, reconfigurable and can be assembled in less time than is required for conventionally fabricated parts. The controller, including the control algorithm and human-machine interface (HMI, is coded using the Borland C++ Builder 6 Personal software environment. The integration of the motion controller with image recognition into an opto-mechatronics system is presented. The robot system has been entered into robotic competitions in Taiwan. The experimental results reveal that the proposed DELTA robot completed the tasks in those competitions successfully.

  1. Symbolic power, robotting, and surveilling

    DEFF Research Database (Denmark)

    Skovsmose, Ole

    2012-01-01

    describes as it prioritises is discussed with reference to robotting and surveillance. In general, the symbolic power of mathematics and formal languages is summarised through the observations: that mathematics treats parts and properties as autonomous, that it dismembers what it addresses and destroys...

  2. Exploring the role of robots

    DEFF Research Database (Denmark)

    Kilbourn, Kyle; Bay, Marie Brøndum

    2011-01-01

    a welfare technology project and our early attempts at performing relations in the context of robotics and automation, assumed to be an integral part of sterilization work for medical instruments. We focus on several aspects of the project: relations between work within and outside of the project...

  3. Wireless Communication Enhancement Methods for Mobile Robots in Radiation Environments

    CERN Document Server

    Nattanmai Parasuraman, Ramviyas; Ferre, Manuel

    In hostile environments such as in scientific facilities where ionising radiation is a dominant hazard, reducing human interventions by increasing robotic operations are desirable. CERN, the European Organization for Nuclear Research, has around 50 km of underground scientific facilities, where wireless mobile robots could help in the operation of the accelerator complex, e.g. in conducting remote inspections and radiation surveys in different areas. The main challenges to be considered here are not only that the robots should be able to go over long distances and operate for relatively long periods, but also the underground tunnel environment, the possible presence of electromagnetic fields, radiation effects, and the fact that the robots shall in no way interrupt the operation of the accelerators. Having a reliable and robust wireless communication system is essential for successful execution of such robotic missions and to avoid situations of manual recovery of the robots in the event that the robot runs ...

  4. Robots and ICT to support play in children with severe physical disabilities: a systematic review.

    Science.gov (United States)

    van den Heuvel, Renée J F; Lexis, Monique A S; Gelderblom, Gert Jan; Jansens, Rianne M L; de Witte, Luc P

    2015-09-02

    Play is an essential part of children's lives. Children with physical disabilities experience difficulties in play, especially those with severe physical disabilities. With the progress of innovative technology, the possibilities to support play are increasing. The purpose of this literature study is to gain insight into the aims, control options and commercial availability of information and communication technology (ICT) and robots to support play (especially play for the sake of play) in children with severe physical disabilities. A systematic literature search in the databases PubMed, CINAHL, IEEE and ERIC was carried out. Titles and abstracts were assessed independently by three reviewers. In addition, studies were selected using Google Scholar, conference proceedings and reference lists. Three main groups of technology for play could be distinguished: robots (n = 8), virtual reality systems (n = 15) and computer systems (n = 4). Besides, ICT and robots developed for specific therapy or educational goals using play-like activities, five of the in total 27 technologies in this study described the aim of "play for play's sake". Many ICT systems and robots to support play in children with physical disabilities were found. Numerous technologies use play-like activities to achieve therapeutic or educational goals. Robots especially are used for "play for play's sake". Implications for Rehabilitation This study gives insight into the aims, control options and commercial availability for application of robots and ICT to support play in children with severe physical disabilities. This overview can be used in both the fields of rehabilitation and special education to search for new innovative intervention options and it can stimulate them to use these innovative play materials. Especially robots may have great potential in supporting "play for play's sake".

  5. Early Intervention and Maltreated Children: A Current Look at the Child Abuse Prevention and Treatment Act and Part C

    Science.gov (United States)

    Moxley, Kathleen M.; Squires, Jane; Lindstrom, Lauren

    2012-01-01

    Current literature regarding the prevalence of child abuse and neglect, resulting developmental impacts on children, and early intervention services for children and families involved in the child welfare system is summarized. While early intervention eligibility referrals are mandated for this population under the Child Abuse Prevention and…

  6. 32 CFR Appendix E to Part 57 - DoD-CC on Early Intervention, Special Education, and Related Services

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 1 2010-07-01 2010-07-01 false DoD-CC on Early Intervention, Special Education... SECRETARY OF DEFENSE PERSONNEL, MILITARY AND CIVILIAN PROVISION OF EARLY INTERVENTION AND SPECIAL EDUCATION..., Special Education, and Related Services A. Committee Membership The DoD-CC shall meet at least yearly to...

  7. The state of the art in non‐pharmacological interventions for developmental stuttering. Part 1: a systematic review of effectiveness

    Science.gov (United States)

    Johnson, Maxine; Blank, Lindsay; Cantrell, Anna; Brumfitt, Shelagh; Enderby, Pam; Goyder, Elizabeth

    2015-01-01

    Abstract Background The growing range of available treatment options for people who stutter presents a challenge for clinicians, service managers and commissioners, who need to have access to the best available treatment evidence to guide them in providing the most appropriate interventions. While a number of reviews of interventions for specific populations or a specific type of intervention have been carried out, a broad‐based systematic review across all forms of intervention for adults and children was needed to provide evidence to underpin future guidelines, inform the implementation of effective treatments and identify future research priorities. Aims To identify and synthesize the published research evidence on the clinical effectiveness of the broad range of non‐pharmacological interventions for the management of developmental stuttering. Methods & Procedures A systematic review of the literature reporting interventions for developmental stuttering was carried out between August 2013 and April 2014. Searches were not limited by language or location, but were restricted by date to studies published from 1990 onwards. Methods for the identification of relevant studies included electronic database searching, reference list checking, citation searching and hand searching of key journals. Appraisal of study quality was performed using a tool based on established criteria for considering risk of bias. Due to heterogeneity in intervention content and outcomes, a narrative synthesis was completed. Main Contribution The review included all available types of intervention and found that most may be of benefit to at least some people who stutter. There was evidence, however, of considerable individual variation in response to these interventions. The review indicated that effects could be maintained following all types of interventions (although this was weakest with regard to feedback and technology interventions). Conclusions This review highlights a need for

  8. From Child-Robot Interaction to Child-Robot-Therapist Interaction: A Case Study in Autism

    Directory of Open Access Journals (Sweden)

    I. Giannopulu

    2012-01-01

    Full Text Available Troubles in social communication as well as deficits in the cognitive treatment of emotions are supposed to be a fundamental part of autism. We present a case study based on multimodal interaction between a mobile robot and a child with autism in spontaneous, free game play. This case study tells us that the robot mediates the interaction between the autistic child and therapist once the robot-child interaction has been established. In addition, the child uses the robot as a mediator to express positive emotion playing with the therapist. It is thought that the three-pronged interaction i.e., child-robot-therapist could better facilitate the transfer of social and emotional abilities to real life settings. Robot therapy has a high potential to improve the condition of brain activity in autistic children.

  9. Educational Robotics as Mindtools

    Science.gov (United States)

    Mikropoulos, Tassos A.; Bellou, Ioanna

    2013-01-01

    Although there are many studies on the constructionist use of educational robotics, they have certain limitations. Some of them refer to robotics education, rather than educational robotics. Others follow a constructionist approach, but give emphasis only to design skills, creativity and collaboration. Some studies use robotics as an educational…

  10. ROILA : RObot Interaction LAnguage

    NARCIS (Netherlands)

    Mubin, O.

    2011-01-01

    The number of robots in our society is increasing rapidly. The number of service robots that interact with everyday people already outnumbers industrial robots. The easiest way to communicate with these service robots, such as Roomba or Nao, would be natural speech. However, the limitations

  11. Robotic Hand

    Science.gov (United States)

    1993-01-01

    The Omni-Hand was developed by Ross-Hime Designs, Inc. for Marshall Space Flight Center (MSFC) under a Small Business Innovation Research (SBIR) contract. The multiple digit hand has an opposable thumb and a flexible wrist. Electric muscles called Minnacs power wrist joints and the interchangeable digits. Two hands have been delivered to NASA for evaluation for potential use on space missions and the unit is commercially available for applications like hazardous materials handling and manufacturing automation. Previous SBIR contracts resulted in the Omni-Wrist and Omni-Wrist II robotic systems, which are commercially available for spray painting, sealing, ultrasonic testing, as well as other uses.

  12. Interventional treatment of common congenital heart diseases: the common view of Chinese medical experts. Part Five-transcatheter intervention for the treatment of compound congenital cardiac anomalies

    International Nuclear Information System (INIS)

    Committee on Congenital Heart Diseases, Internal Medicine Branch of Cadiovascular Diseases of China Physicians' Association

    2011-01-01

    Compound congenital cardiac anomalies refer to two or more congenital cardiovascular defects coexisting in the same patient. Transcatheter intervention for compound congenital cardiac anomalies has got satisfactory results in recent years. However, the percutaneous closure procedure used for compound congenital cardiac defects does not mean the simple addition of single interventional technique. Clinically, it needs more specialist expertise to deal with such complex defects. This chapter will briefly describe the pathophysiology and clinical features of the following compound congenital cardiac anomalies: the ventricular septal defect (VSD) with coexistence of atrial septal defect (ASD), patent ductus arteriosus (PDA) or pulmonary valve stenosis (PS), the ASD coexistence of PDA, PS or mitral stenosis (Lutembacher's syndrome), and coarctation of aorta compound with PDA. The indications and contraindications, the therapeutic principles, the matters needing attention, the postoperative management, the judgment of curative effect, etc. of using transcatheter for the treatment of such compound anomalies will also be discussed. (authors)

  13. Interventional treatment of common congenital heart diseases: the common view of Chinese medical experts. Part Five-transcatheter intervention for the treatment of compound congenital cardiac anomalies

    Energy Technology Data Exchange (ETDEWEB)

    Committee on Congenital Heart Diseases, Internal Medicine Branch of Cadiovascular Diseases of China Physicians' Association

    2011-05-15

    Compound congenital cardiac anomalies refer to two or more congenital cardiovascular defects coexisting in the same patient. Transcatheter intervention for compound congenital cardiac anomalies has got satisfactory results in recent years. However, the percutaneous closure procedure used for compound congenital cardiac defects does not mean the simple addition of single interventional technique. Clinically, it needs more specialist expertise to deal with such complex defects. This chapter will briefly describe the pathophysiology and clinical features of the following compound congenital cardiac anomalies: the ventricular septal defect (VSD) with coexistence of atrial septal defect (ASD), patent ductus arteriosus (PDA) or pulmonary valve stenosis (PS), the ASD coexistence of PDA, PS or mitral stenosis (Lutembacher's syndrome), and coarctation of aorta compound with PDA. The indications and contraindications, the therapeutic principles, the matters needing attention, the postoperative management, the judgment of curative effect, etc. of using transcatheter for the treatment of such compound anomalies will also be discussed. (authors)

  14. Modeling and simulation of tumor-influenced high resolution real-time physics-based breast models for model-guided robotic interventions

    Science.gov (United States)

    Neylon, John; Hasse, Katelyn; Sheng, Ke; Santhanam, Anand P.

    2016-03-01

    Breast radiation therapy is typically delivered to the patient in either supine or prone position. Each of these positioning systems has its limitations in terms of tumor localization, dose to the surrounding normal structures, and patient comfort. We envision developing a pneumatically controlled breast immobilization device that will enable the benefits of both supine and prone positioning. In this paper, we present a physics-based breast deformable model that aids in both the design of the breast immobilization device as well as a control module for the device during every day positioning. The model geometry is generated from a subject's CT scan acquired during the treatment planning stage. A GPU based deformable model is then generated for the breast. A mass-spring-damper approach is then employed for the deformable model, with the spring modeled to represent a hyperelastic tissue behavior. Each voxel of the CT scan is then associated with a mass element, which gives the model its high resolution nature. The subject specific elasticity is then estimated from a CT scan in prone position. Our results show that the model can deform at >60 deformations per second, which satisfies the real-time requirement for robotic positioning. The model interacts with a computer designed immobilization device to position the breast and tumor anatomy in a reproducible location. The design of the immobilization device was also systematically varied based on the breast geometry, tumor location, elasticity distribution and the reproducibility of the desired tumor location.

  15. Robotics Algorithms Provide Nutritional Guidelines

    Science.gov (United States)

    2009-01-01

    On July 5, 1997, a small robot emerged from its lander like an insect from an egg, crawling out onto the rocky surface of Mars. About the size of a child s wagon, NASA s Sojourner robot was the first successful rover mission to the Red Planet. For 83 sols (Martian days, typically about 40 minutes longer than Earth days), Sojourner - largely remote controlled by NASA operators on Earth - transmitted photos and data unlike any previously collected. Sojourner was perhaps the crowning achievement of the NASA Space Telerobotics Program, an Agency initiative designed to push the limits of robotics in space. Telerobotics - devices that merge the autonomy of robotics with the direct human control of teleoperators - was already a part of NASA s efforts; probes like the Viking landers that preceded Sojourner on Mars, for example, were telerobotic applications. The Space Telerobotics Program, a collaboration between Ames Research Center, Johnson Space Center, Jet Propulsion Laboratory (JPL), and multiple universities, focused on developing remote-controlled robotics for three main purposes: on-orbit assembly and servicing, science payload tending, and planetary surface robotics. The overarching goal was to create robots that could be guided to build structures in space, monitor scientific experiments, and, like Sojourner, scout distant planets in advance of human explorers. While telerobotics remains a significant aspect of NASA s efforts, as evidenced by the currently operating Spirit and Opportunity Mars rovers, the Hubble Space Telescope, and many others - the Space Telerobotics Program was dissolved and redistributed within the Agency the same year as Sojourner s success. The program produced a host of remarkable technologies and surprising inspirations, including one that is changing the way people eat

  16. Laboratory robotics systems at the Savannah River Laboratory

    International Nuclear Information System (INIS)

    Dyches, G.M.; Burkett, S.D.

    1983-01-01

    Many analytical chemistry methods normally used at the Savannah River site require repetitive procedures and handling of radioactive and other hazardous solutions. Robotics is being investigated as a method of reducing personnel fatigue and radiation exposure and also increasing product quality. Several applications of various commercially available robot systems are discussed involving cold (nonradioactive) and hot (radioactive) sample preparations and glovebox waste removal. Problems encountered in robot programming, parts fixturing, design of special robot hands and other support equipment, glovebox operation, and operator-system interaction are discussed. A typical robot system cost analysis for one application is given

  17. On Throughput Maximization in Constant Travel-Time Robotic Cells

    OpenAIRE

    Milind Dawande; Chelliah Sriskandarajah; Suresh Sethi

    2002-01-01

    We consider the problem of scheduling operations in bufferless robotic cells that produce identical parts. The objective is to find a cyclic sequence of robot moves that minimizes the long-run average time to produce a part or, equivalently, maximizes the throughput rate. The robot can be moved in simple cycles that produce one unit or, in more complicated cycles, that produce multiple units. Because one-unit cycles are the easiest to understand, implement, and control, they are widely used i...

  18. Current approaches to treatments for schizophrenia spectrum disorders, part II: psychosocial interventions and patient-focused perspectives in psychiatric care

    Directory of Open Access Journals (Sweden)

    Chien WT

    2013-09-01

    Full Text Available Wai Tong Chien, Sau Fong Leung, Frederick KK Yeung, Wai Kit Wong School of Nursing, Faculty of Health and Social Sciences, The Hong Kong Polytechnic University, Hung Hom, Kowloon, Hong Kong Abstract: Schizophrenia is a disabling psychiatric illness associated with disruptions in cognition, emotion, and psychosocial and occupational functioning. Increasing evidence shows that psychosocial interventions for people with schizophrenia, as an adjunct to medications or usual psychiatric care, can reduce psychotic symptoms and relapse and improve patients' long-term outcomes such as recovery, remission, and illness progression. This critical review of the literature was conducted to identify the common approaches to psychosocial interventions for people with schizophrenia. Treatment planning and outcomes were also explored and discussed to better understand the effects of these interventions in terms of person-focused perspectives such as their perceived quality of life and satisfaction and their acceptability and adherence to treatments or services received. We searched major healthcare databases such as EMBASE, MEDLINE, and PsycLIT and identified relevant literature in English from these databases. Their reference lists were screened, and studies were selected if they met the criteria of using a randomized controlled trial or systematic review design, giving a clear description of the interventions used, and having a study sample of people primarily diagnosed with schizophrenia. Five main approaches to psychosocial intervention had been used for the treatment of schizophrenia: cognitive therapy (cognitive behavioral and cognitive remediation therapy, psychoeducation, family intervention, social skills training, and assertive community treatment. Most of these five approaches applied to people with schizophrenia have demonstrated satisfactory levels of short- to medium-term clinical efficacy in terms of symptom control or reduction, level of

  19. Modular Robotic Wearable

    DEFF Research Database (Denmark)

    Lund, Henrik Hautop; Pagliarini, Luigi

    2009-01-01

    In this concept paper we trace the contours and define a new approach to robotic systems, composed of interactive robotic modules which are somehow worn on the body. We label such a field as Modular Robotic Wearable (MRW). We describe how, by using modular robotics for creating wearable....... Finally, by focusing on the intersection of the combination modular robotic systems, wearability, and bodymind we attempt to explore the theoretical characteristics of such approach and exploit the possible playware application fields....

  20. Teaching Functional Patterns through Robotic Applications

    Directory of Open Access Journals (Sweden)

    J. Boender

    2016-11-01

    Full Text Available We present our approach to teaching functional programming to First Year Computer Science students at Middlesex University through projects in robotics. A holistic approach is taken to the curriculum, emphasising the connections between different subject areas. A key part of the students' learning is through practical projects that draw upon and integrate the taught material. To support these, we developed the Middlesex Robotic plaTfOrm (MIRTO, an open-source platform built using Raspberry Pi, Arduino, HUB-ee wheels and running Racket (a LISP dialect. In this paper we present the motivations for our choices and explain how a number of concepts of functional programming may be employed when programming robotic applications. We present some students' work with robotics projects: we consider the use of robotics projects to have been a success, both for their value in reinforcing students' understanding of programming concepts and for their value in motivating the students.

  1. 8th International Robotic Sailing Conference

    CERN Document Server

    Haug, Florian

    2016-01-01

    This book presents the cutting edge developments within a broad field related to robotic sailing. The contributions were presented during the 8th International Robotic Sailing Conference, which has taken place as a part of the 2015 World Robotic Sailing Championships in Mariehamn, Åland (Finland), August 31st – September 4th 2015. Since more than a decade, a series of competitions such as the World Robotic Sailing Championship have stimulated a variety of groups to work on research and development around autonomous sailing robots, which involves boat designers, naval architects, electrical engineers and computer scientists. While many of the challenges in building a truly autonomous sailboat are still unsolved, the books presents the state of the art of research and development within platform optimization, route and stability planning, collision avoidance, power management and boat control.

  2. Y-12 Plant decontamination and decommissioning technology logic diagram for Building 9201-4. Volume 3: Technology evaluation data sheets; Part B: Decontamination, robotics/automation, waste management

    International Nuclear Information System (INIS)

    1994-09-01

    The Y-12 Plant Decontamination and Decommissioning Technology Logic Diagram for Building 9201-4 (TLD) was developed to provide a decision-support tool that relates decontamination and decommissioning (D and D) problems at Bldg. 9201-4 to potential technologies that can remediate these problems. The TLD uses information from the Strategic Roadmap for the Oak Ridge Reservation, the Oak Ridge K-25 Site Technology Logic Diagram, the Oak Ridge National Laboratory Technology Logic Diagram, and a previous Hanford logic diagram. This TLD identifies the research, development, demonstration, testing, and evaluation needed for sufficient development of these technologies to allow for technology transfer and application to D and D and waste management (WM) activities. It is essential that follow-on engineering studies be conducted to build on the output of this project. These studies will begin by selecting the most promising technologies identified in the TLD and by finding an optimum mix of technologies that will provide a socially acceptable balance between cost and risk. This report consists of the decontamination, robotics/automation, and WM data sheets

  3. Oak Ridge K-25 Site Technology Logic Diagram. Volume 3, Technology evaluation data sheets; Part B, Remedial action, robotics/automation, waste management

    Energy Technology Data Exchange (ETDEWEB)

    Fellows, R.L. [ed.

    1993-02-26

    The Oak Ridge K-25 Technology Logic Diagram (TLD), a decision support tool for the K-25 Site, was developed to provide a planning document that relates environmental restoration (ER) and waste management (WN) problems at the Oak Ridge K-25 Site. The TLD technique identifies the research necessary to develop these technologies to a state that allows for technology transfer and application to waste management, remediation, decontamination, and decommissioning activities. The TLD consists of four separate volumes-Vol. 1, Vol. 2, Vol. 3A, and Vol. 3B. Volume 1 provides introductory and overview information about the TLD. Volume 2 contains logic diagrams. Volume 3 has been divided into two separate volumes to facilitate handling and use. This volume 3 B provides the Technology Evaluation Data Sheets (TEDS) for ER/WM activities (Remedial Action Robotics and Automation, Waste Management) that are referenced by a TEDS code number in Vol. 2 of the TLD. Each of these sheets represents a single logic trace across the TLD. These sheets contain more detail than each technology in Vol. 2. The TEDS are arranged alphanumerically by the TEDS code number in the upper right corner of each data sheet. Volume 3 can be used in two ways: (1) technologies that are identified from Vol. 2 can be referenced directly in Vol. 3 by using the TEDS codes, and (2) technologies and general technology areas (alternatives) can be located in the index in the front of this volume.

  4. HIV risk and behaviour among part-time versus professional FSW: baseline report of an interventional cohort in Burkina Faso.

    Science.gov (United States)

    Traore, Isidore T; Hema, Noelie M; Sanon, Anselme; Some, Felicien; Ouedraogo, Djeneba; Some, Roselyne; Niessougou, Josiane; Konate, Issouf; Mayaud, Philippe; Van De Perre, Philippe; Meda, Nicolas; Nagot, Nicolas

    2016-02-01

    To readjust HIV control programmes in Africa, we assessed the factors associated with high-risk behaviours and HIV infection among young female sex workers (FSW) in Burkina Faso. We carried out a cross-sectional study from September 2009 to September 2010 in Ouagadougou, the capital city. FSW were categorised as professionals and part-time sex workers (PTSW). After a face-to-face questionnaire, blood and urine samples were collected for HIV, HSV-2, genital infections and pregnancy. High-risk behaviour was defined as a recent unprotected sex with either casual clients, regular clients or regular partners. We recruited 609 FSW including 188 (30.9%) professionals. Their median age was 21 years (IQR 19-23), and the prevalence of HIV was 10.3% among professionals and 6.5% among PTSW. Only 3 of 46 HIV-infected women were aware of their status. Overall, 277 (45.6%) women reported high-risk behaviours (41.2% among professionals and 47.5% among PTSW), which were driven mainly by non-systematic condom use with regular partners. In multivariable analysis, PTSW (adjusted OR (AOR)=1.89; 95% CI 1.27 to 2.82) and having a primary (AOR=1.75; 95% CI 1.15 to 2.67) or higher education level (AOR=1.80; 95% CI 1.13 to 2.89) remained associated with high-risk behaviours. HIV infection was associated with older age (AOR=1.44; 95% CI 1.22 to 1.71), with being married/cohabiting (AOR=2.70; 95% CI 1.21 to 6.04) and with Trichomonas vaginalis infection (AOR=9.63; 95% CI 2.93 to 31.59), while history of HIV testing was associated with a decreased risk (AOR=0.18; 95% CI 0.08 to 0.40). This study highlights the need for targeted interventions among young FSW focusing particularly on PTSW, sexual behaviours with regular partners and regular HIV testing. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

  5. An ultra-high field strength MR image-guided robotic needle delivery system for in-bore small animal interventions.

    Science.gov (United States)

    Gravett, Matthew; Cepek, Jeremy; Fenster, Aaron

    2017-11-01

    The purpose of this study was to develop and validate an image-guided robotic needle delivery system for accurate and repeatable needle targeting procedures in mouse brains inside the 12 cm inner diameter gradient coil insert of a 9.4 T MR scanner. Many preclinical research techniques require the use of accurate needle deliveries to soft tissues, including brain tissue. Soft tissues are optimally visualized in MR images, which offer high-soft tissue contrast, as well as a range of unique imaging techniques, including functional, spectroscopy and thermal imaging, however, there are currently no solutions for delivering needles to small animal brains inside the bore of an ultra-high field MR scanner. This paper describes the mechatronic design, evaluation of MR compatibility, registration technique, mechanical calibration, the quantitative validation of the in-bore image-guided needle targeting accuracy and repeatability, and demonstrated the system's ability to deliver needles in situ. Our six degree-of-freedom, MR compatible, mechatronic system was designed to fit inside the bore of a 9.4 T MR scanner and is actuated using a combination of piezoelectric and hydraulic mechanisms. The MR compatibility and targeting accuracy of the needle delivery system are evaluated to ensure that the system is precisely calibrated to perform the needle targeting procedures. A semi-automated image registration is performed to link the robot coordinates to the MR coordinate system. Soft tissue targets can be accurately localized in MR images, followed by automatic alignment of the needle trajectory to the target. Intra-procedure visualization of the needle target location and the needle were confirmed through MR images after needle insertion. The effects of geometric distortions and signal noise were found to be below threshold that would have an impact on the accuracy of the system. The system was found to have negligible effect on the MR image signal noise and geometric distortion

  6. ALLIANCE: An architecture for fault tolerant multi-robot cooperation

    Energy Technology Data Exchange (ETDEWEB)

    Parker, L.E.

    1995-02-01

    ALLIANCE is a software architecture that facilitates the fault tolerant cooperative control of teams of heterogeneous mobile robots performing missions composed of loosely coupled, largely independent subtasks. ALLIANCE allows teams of robots, each of which possesses a variety of high-level functions that it can perform during a mission, to individually select appropriate actions throughout the mission based on the requirements of the mission, the activities of other robots, the current environmental conditions, and the robot`s own internal states. ALLIANCE is a fully distributed, behavior-based architecture that incorporates the use of mathematically modeled motivations (such as impatience and acquiescence) within each robot to achieve adaptive action selection. Since cooperative robotic teams usually work in dynamic and unpredictable environments, this software architecture allows the robot team members to respond robustly, reliably, flexibly, and coherently to unexpected environmental changes and modifications in the robot team that may occur due to mechanical failure, the learning of new skills, or the addition or removal of robots from the team by human intervention. The feasibility of this architecture is demonstrated in an implementation on a team of mobile robots performing a laboratory version of hazardous waste cleanup.

  7. Intelligent robotics can boost America's economic growth

    Science.gov (United States)

    Erickson, Jon D.

    1994-01-01

    A case is made for strategic investment in intelligent robotics as a part of the solution to the problem of improved global competitiveness for U.S. manufacturing, a critical industrial sector. Similar cases are made for strategic investments in intelligent robotics for field applications, construction, and service industries such as health care. The scope of the country's problems and needs is beyond the capability of the private sector alone, government alone, or academia alone to solve independently of the others. National cooperative programs in intelligent robotics are needed with the private sector supplying leadership direction and aerospace and non-aerospace industries conducting the development. Some necessary elements of such programs are outlined. The National Aeronautics and Space Administration (NASA) and the Lyndon B. Johnson Space Center (JSC) can be key players in such national cooperative programs in intelligent robotics for several reasons: (1) human space exploration missions require supervised intelligent robotics as enabling tools and, hence must develop supervised intelligent robotic systems; (2) intelligent robotic technology is being developed for space applications at JSC (but has a strong crosscutting or generic flavor) that is advancing the state of the art and is producing both skilled personnel and adaptable developmental infrastructure such as integrated testbeds; and (3) a NASA JSC Technology Investment Program in Robotics has been proposed based on commercial partnerships and collaborations for precompetitive, dual-use developments.

  8. Can text messages reach the parts other process measures cannot reach: an evaluation of a behavior change intervention delivered by mobile phone?

    Directory of Open Access Journals (Sweden)

    Linda Irvine

    Full Text Available BACKGROUND: Process evaluation is essential in developing, piloting and evaluating complex interventions. This often involves observation of intervention delivery and interviews with study participants. Mobile telephone interventions involve no face to face contact, making conventional process evaluation difficult. This study assesses the utility of novel techniques for process evaluation involving no face to face contact. METHODS: Text messages were delivered to 34 disadvantaged men as part of a feasibility study of a brief alcohol intervention. Process evaluation focused on delivery of the text messages and responses received from study participants. The computerized delivery system captured data on receipt of the messages. The text messages, delivered over 28 days, included nine which asked questions. Responses to these questions served as one technique for process evaluation by ascertaining the nature of engagement with the study and with steps on the causal chain to behavior change. RESULTS: A total of 646 SMS text messages were sent to participants. Of these, 613 messages (95% were recorded as delivered to participants' telephones. 88% of participants responded to messages that asked questions. There was little attenuation in responses to the questions across the intervention period. Content analysis of the responses revealed that participants engaged with text messages, thought deeply about their content and provided carefully considered personal responses to the questions. CONCLUSIONS: Socially disadvantaged men, a hard to reach population, engaged in a meaningful way over a sustained period with an interactive intervention delivered by text message. The novel process measures used in the study are unobtrusive, low cost and collect real-time data on all participants. They assessed the fidelity of delivery of the intervention and monitored retention in the study. They measured levels of engagement and identified participants' reactions to

  9. Robotic lateral pancreaticojejunostomy (Puestow).

    Science.gov (United States)

    Meehan, John J; Sawin, Robert

    2011-06-01

    A lateral pancreaticojejunostomy (LPJ), also known as the Puestow procedure, is a complex procedure performed for chronic pancreatitis when the pancreatic duct is dilated and unable to drain properly. Traditionally, these procedures are performed with open surgery. A minimally invasive approach to the LPJ using rigid handheld nonarticulating instruments is tedious and rarely performed. In fact, there are no prior laparoscopic case reports for LPJ in children and only a small handful of cases in the adult literature. This lack of laparoscopic information may be an indication of the difficulty in performing this complex operation with nonarticulating laparoscopic instruments. The advantages of robotic surgery may help overcome these difficulties. We present the first robotic LPJ ever reported in a 14-year-old child with idiopathic chronic pancreatitis. This case demonstrates the utility of this advanced surgical technology and may lead to a new minimally invasive option for both adults and children with chronic pancreatitis requiring surgical intervention. Copyright © 2011 Elsevier Inc. All rights reserved.

  10. Next generation light robotic

    DEFF Research Database (Denmark)

    Villangca, Mark Jayson; Palima, Darwin; Banas, Andrew Rafael

    2017-01-01

    -assisted surgery imbibes surgeons with superhuman abilities and gives the expression “surgical precision” a whole new meaning. Still in its infancy, much remains to be done to improve human-robot collaboration both in realizing robots that can operate safely with humans and in training personnel that can work......Conventional robotics provides machines and robots that can replace and surpass human performance in repetitive, difficult, and even dangerous tasks at industrial assembly lines, hazardous environments, or even at remote planets. A new class of robotic systems no longer aims to replace humans...... with so-called automatons but, rather, to create robots that can work alongside human operators. These new robots are intended to collaborate with humans—extending their abilities—from assisting workers on the factory floor to rehabilitating patients in their homes. In medical robotics, robot...

  11. Distributed Robotics Education

    DEFF Research Database (Denmark)

    Lund, Henrik Hautop; Pagliarini, Luigi

    2011-01-01

    Distributed robotics takes many forms, for instance, multirobots, modular robots, and self-reconfigurable robots. The understanding and development of such advanced robotic systems demand extensive knowledge in engineering and computer science. In this paper, we describe the concept of a distribu......Distributed robotics takes many forms, for instance, multirobots, modular robots, and self-reconfigurable robots. The understanding and development of such advanced robotic systems demand extensive knowledge in engineering and computer science. In this paper, we describe the concept...... to be changed, related to multirobot control and human-robot interaction control from virtual to physical representation. The proposed system is valuable for bringing a vast number of issues into education – such as parallel programming, distribution, communication protocols, master dependency, connectivity...

  12. An Adaptive Robot Game

    DEFF Research Database (Denmark)

    Hansen, Søren Tranberg; Svenstrup, Mikael; Dalgaard, Lars

    2010-01-01

    The goal of this paper is to describe an adaptive robot game, which motivates elderly people to do a regular amount of physical exercise while playing. One of the advantages of robot based games is that the initiative to play can be taken autonomously by the robot. In this case, the goal is to im......The goal of this paper is to describe an adaptive robot game, which motivates elderly people to do a regular amount of physical exercise while playing. One of the advantages of robot based games is that the initiative to play can be taken autonomously by the robot. In this case, the goal...... is to improve the mental and physical state of the user by playing a physical game with the robot. Ideally, a robot game should be simple to learn but difficult to master, providing an appropriate degree of challenge for players with different skills. In order to achieve that, the robot should be able to adapt...

  13. Robotic membranes

    DEFF Research Database (Denmark)

    Ramsgaard Thomsen, Mette

    2008-01-01

    The relationship between digital and analogue is often constructed as one of opposition. The perception that the world is permeated with underlying patterns of data, describing events and matter alike, suggests that information can be understood apart from the substance to which it is associated......, and that its encoded logic can be constructed and reconfigured as an isolated entity. This disembodiment of information from materiality implies that an event like a thunderstorm, or a material like a body, can be described equally by data, in other words it can be read or written. The following prototypes......, Vivisection and Strange Metabolisms, were developed at the Centre for Information Technology and Architecture (CITA) at the Royal Danish Academy of Fine Arts in Copenhagen as a means of engaging intangible digital data with tactile physical material. As robotic membranes, they are a dual examination...

  14. Performance Evaluation Methods for Assistive Robotic Technology

    Science.gov (United States)

    Tsui, Katherine M.; Feil-Seifer, David J.; Matarić, Maja J.; Yanco, Holly A.

    Robots have been developed for several assistive technology domains, including intervention for Autism Spectrum Disorders, eldercare, and post-stroke rehabilitation. Assistive robots have also been used to promote independent living through the use of devices such as intelligent wheelchairs, assistive robotic arms, and external limb prostheses. Work in the broad field of assistive robotic technology can be divided into two major research phases: technology development, in which new devices, software, and interfaces are created; and clinical, in which assistive technology is applied to a given end-user population. Moving from technology development towards clinical applications is a significant challenge. Developing performance metrics for assistive robots poses a related set of challenges. In this paper, we survey several areas of assistive robotic technology in order to derive and demonstrate domain-specific means for evaluating the performance of such systems. We also present two case studies of applied performance measures and a discussion regarding the ubiquity of functional performance measures across the sampled domains. Finally, we present guidelines for incorporating human performance metrics into end-user evaluations of assistive robotic technologies.

  15. Minimizing Hexapod Robot Foot Deviations Using Multilayer Perceptron

    Directory of Open Access Journals (Sweden)

    Vytautas Valaitis

    2015-12-01

    Full Text Available Rough-terrain traversability is one of the most valuable characteristics of walking robots. Even despite their slower speeds and more complex control algorithms, walking robots have far wider usability than wheeled or tracked robots. However, efficient movement over irregular surfaces can only be achieved by eliminating all possible difficulties, which in many cases are caused by a high number of degrees of freedom, feet slippage, frictions and inertias between different robot parts or even badly developed inverse kinematics (IK. In this paper we address the hexapod robot-foot deviation problem. We compare the foot-positioning accuracy of unconfigured inverse kinematics and Multilayer Perceptron-based (MLP methods via theory, computer modelling and experiments on a physical robot. Using MLP-based methods, we were able to significantly decrease deviations while reaching desired positions with the hexapod's foot. Furthermore, this method is able to compensate for deviations of the robot arising from any possible reason.

  16. Approaches to probabilistic model learning for mobile manipulation robots

    CERN Document Server

    Sturm, Jürgen

    2013-01-01

    Mobile manipulation robots are envisioned to provide many useful services both in domestic environments as well as in the industrial context. Examples include domestic service robots that implement large parts of the housework, and versatile industrial assistants that provide automation, transportation, inspection, and monitoring services. The challenge in these applications is that the robots have to function under changing, real-world conditions, be able to deal with considerable amounts of noise and uncertainty, and operate without the supervision of an expert. This book presents novel learning techniques that enable mobile manipulation robots, i.e., mobile platforms with one or more robotic manipulators, to autonomously adapt to new or changing situations. The approaches presented in this book cover the following topics: (1) learning the robot's kinematic structure and properties using actuation and visual feedback, (2) learning about articulated objects in the environment in which the robot is operating,...

  17. Distributed computing by oblivious mobile robots

    CERN Document Server

    Flocchini, Paola; Santoro, Nicola

    2012-01-01

    The study of what can be computed by a team of autonomous mobile robots, originally started in robotics and AI, has become increasingly popular in theoretical computer science (especially in distributed computing), where it is now an integral part of the investigations on computability by mobile entities. The robots are identical computational entities located and able to move in a spatial universe; they operate without explicit communication and are usually unable to remember the past; they are extremely simple, with limited resources, and individually quite weak. However, collectively the ro

  18. Robot development for nuclear material processing

    International Nuclear Information System (INIS)

    Pedrotti, L.R.; Armantrout, G.A.; Allen, D.C.; Sievers, R.H. Sr.

    1991-07-01

    The Department of Energy is seeking to modernize its special nuclear material (SNM) production facilities and concurrently reduce radiation exposures and process and incidental radioactive waste generated. As part of this program, Lawrence Livermore National Laboratory (LLNL) lead team is developing and adapting generic and specific applications of commercial robotic technologies to SNM pyrochemical processing and other operations. A working gantry robot within a sealed processing glove box and a telerobot control test bed are manifestations of this effort. This paper describes the development challenges and progress in adapting processing, robotic, and nuclear safety technologies to the application. 3 figs

  19. Robotics Potential Fields

    Directory of Open Access Journals (Sweden)

    Jordi Lucero

    2009-01-01

    Full Text Available This problem was to calculate the path a robot would take to navigate an obstacle field and get to its goal. Three obstacles were given as negative potential fields which the robot avoided, and a goal was given a positive potential field that attracted the robot. The robot decided each step based on its distance, angle, and influence from every object. After each step, the robot recalculated and determined its next step until it reached its goal. The robot's calculations and steps were simulated with Microsoft Excel.

  20. Designing Emotionally Expressive Robots

    DEFF Research Database (Denmark)

    Tsiourti, Christiana; Weiss, Astrid; Wac, Katarzyna

    2017-01-01

    Socially assistive agents, be it virtual avatars or robots, need to engage in social interactions with humans and express their internal emotional states, goals, and desires. In this work, we conducted a comparative study to investigate how humans perceive emotional cues expressed by humanoid...... robots through five communication modalities (face, head, body, voice, locomotion) and examined whether the degree of a robot's human-like embodiment affects this perception. In an online survey, we asked people to identify emotions communicated by Pepper -a highly human-like robot and Hobbit – a robot...... for robots....

  1. Advanced mechanics in robotic systems

    CERN Document Server

    Nava Rodríguez, Nestor Eduardo

    2011-01-01

    Illustrates original and ambitious mechanical designs and techniques for the development of new robot prototypes Includes numerous figures, tables and flow charts Discusses relevant applications in robotics fields such as humanoid robots, robotic hands, mobile robots, parallel manipulators and human-centred robots

  2. Safety and efficacy of at-home robotic locomotion therapy in individuals with chronic incomplete spinal cord injury: a prospective, pre-post intervention, proof-of-concept study.

    Directory of Open Access Journals (Sweden)

    Rüdiger Rupp

    Full Text Available The compact Motorized orthosis for home rehabilitation of Gait (MoreGait was developed for continuation of locomotion training at home. MoreGait generates afferent stimuli of walking with the user in a semi-supine position and provides feedback about deviations from the reference walking pattern.Prospective, pre-post intervention, proof-of-concept study to test the feasibility of an unsupervised home-based application of five MoreGait prototypes in subjects with incomplete spinal cord injury (iSCI.Twenty-five (5 tetraplegia, 20 paraplegia participants with chronic (mean time since injury: 5.8 ± 5.4 (standard deviation, SD years sensorimotor iSCI (7 ASIA Impairment Scale (AIS C, 18 AIS D; Walking Index for Spinal Cord Injury (WISCI II: Interquartile range 9 to 16 completed the training (45 minutes / day, at least 4 days / week, 8 weeks. Baseline status was documented 4 and 2 weeks before and at training onset. Training effects were assessed after 4 and 8 weeks of therapy.After therapy, 9 of 25 study participants improved with respect to the dependency on walking aids assessed by the WISCI II. For all individuals, the short-distance walking velocity measured by the 10-Meter Walk Test showed significant improvements compared to baseline (100% for both self-selected (Mean 139.4% ± 35.5% (SD and maximum (Mean 143.1% ± 40.6% (SD speed conditions as well as the endurance estimated with the six-minute walk test (Mean 166.6% ± 72.1% (SD. One device-related adverse event (pressure sore on the big toe occurred in over 800 training sessions.Home-based robotic locomotion training with MoreGait is feasible and safe. The magnitude of functional improvements achieved by MoreGait in individuals with iSCI is well within the range of complex locomotion robots used in hospitals. Thus, unsupervised MoreGait training potentially represents an option to prolong effective training aiming at recovery of locomotor function beyond in-patient rehabilitation

  3. 77 FR 57096 - Part C Early Intervention Services Grant Under the Ryan White HIV/AIDS Program

    Science.gov (United States)

    2012-09-17

    ... Intervention Services Grant Under the Ryan White HIV/AIDS Program AGENCY: Health Resources and Services... primary care services for persons living with HIV/AIDS, including primary adult HIV medical care, adult... Medical Center managed the Ryan White HIV/AIDS Program through a contractual agreement with the...

  4. 75 FR 28263 - Part C Early Intervention Services Grant Under the Ryan White HIV/AIDS Program

    Science.gov (United States)

    2010-05-20

    ... Intervention Services Grant Under the Ryan White HIV/AIDS Program AGENCY: Health Resources and Services... services for persons living with HIV/AIDS, including primary medical care, laboratory testing, oral health... continue providing services after March 31, 2010. HRSA's HIV/AIDS Bureau identified the Rural Health Group...

  5. Race to the Top--Early Learning Challenge: An Analysis of Impact on IDEIA, Part C Early Intervention Programs

    Science.gov (United States)

    Bohjanen, Sharon L.

    2016-01-01

    Infants and toddlers who live in poverty are more likely to experience developmental delays or disabilities and less likely to access early intervention (EI) services. The federal initiative Race to the Top--Early Learning Challenge (RTT-ELC) was designed to increase access to high quality early learning programs for children at risk for…

  6. Soft robot design methodology for `push-button' manufacturing

    Science.gov (United States)

    Paik, Jamie

    2018-06-01

    `Push-button' or fully automated manufacturing would enable the production of robots with zero intervention from human hands. Realizing this utopia requires a fundamental shift from a sequential (design-materials-manufacturing) to a concurrent design methodology.

  7. White Paper: Interventional MRI: Current Status and Potential for Development Considering Economic Perspectives, Part 2: Liver and Other Applications in Oncology.

    Science.gov (United States)

    Barkhausen, Jörg; Kahn, Thomas; Krombach, Gabriele A; Kuhl, Christiane K; Lotz, Joachim; Maintz, David; Ricke, Jens; Schönberg, Stefan O; Vogl, Thomas J; Wacker, Frank K

    2017-11-01

    al. White Paper: Interventional MRI: Current Status and Potential for Development Considering Economic Perspectives, Part 2: Liver and Other Applications in Oncology. Fortschr Röntgenstr 2017; 189: 1047 - 1054. © Georg Thieme Verlag KG Stuttgart · New York.

  8. Robotics_MobileRobot Navigation, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Robots and rovers exploring planets need to autonomously navigate to specified locations. Advanced Scientific Concepts, Inc. (ASC) and the University of Minnesota...

  9. Robots Social Embodiment in Autonomous Mobile Robotics

    Directory of Open Access Journals (Sweden)

    Brian Duffy

    2008-11-01

    Full Text Available This work aims at demonstrating the inherent advantages of embracing a strong notion of social embodiment in designing a real-world robot control architecture with explicit ?intelligent? social behaviour between a collective of robots. It develops the current thinking on embodiment beyond the physical by demonstrating the importance of social embodiment. A social framework develops the fundamental social attributes found when more than one robot co-inhabit a physical space. The social metaphors of identity, character, stereotypes and roles are presented and implemented within a real-world social robot paradigm in order to facilitate the realisation of explicit social goals.

  10. Computer Aided Design of a Low-Cost Painting Robot

    Directory of Open Access Journals (Sweden)

    SYEDA MARIA KHATOON ZAIDI

    2017-10-01

    Full Text Available The application of robots or robotic systems for painting parts is becoming increasingly conventional; to improve reliability, productivity, consistency and to decrease waste. However, in Pakistan only highend Industries are able to afford the luxury of a robotic system for various purposes. In this study we propose an economical Painting Robot that a small-scale industry can install in their plant with ease. The importance of this robot is that being cost effective, it can easily be replaced in small manufacturing industries and therefore, eliminate health problems occurring to the individual in charge of painting parts on an everyday basis. To achieve this aim, the robot is made with local parts with only few exceptions, to cut costs; and the programming language is kept at a mediocre level. Image processing is used to establish object recognition and it can be programmed to paint various simple geometries. The robot is placed on a conveyer belt to maximize productivity. A four DoF (Degree of Freedom arm increases the working envelope and accessibility of painting different shaped parts with ease. This robot is capable of painting up, front, back, left and right sides of the part with a single colour. Initially CAD (Computer Aided Design models of the robot were developed which were analyzed, modified and improved to withstand loading condition and perform its task efficiently. After design selection, appropriate motors and materials were selected and the robot was developed. Throughout the development phase, minor problems and errors were fixed accordingly as they arose. Lastly the robot was integrated with the computer and image processing for autonomous control. The final results demonstrated that the robot is economical and reduces paint wastage.

  11. Computer aided design of a low-cost painting robot

    International Nuclear Information System (INIS)

    Zaidi, S.M.; Janejo, F.; Mujtaba, S.B.

    2017-01-01

    The application of robots or robotic systems for painting parts is becoming increasingly conventional; to improve reliability, productivity, consistency and to decrease waste. However, in Pakistan only highend Industries are able to afford the luxury of a robotic system for various purposes. In this study we propose an economical Painting Robot that a small-scale industry can install in their plant with ease. The importance of this robot is that being cost effective, it can easily be replaced in small manufacturing industries and therefore, eliminate health problems occurring to the individual in charge of painting parts on an everyday basis. To achieve this aim, the robot is made with local parts with only few exceptions, to cut costs; and the programming language is kept at a mediocre level. Image processing is used to establish object recognition and it can be programmed to paint various simple geometries. The robot is placed on a conveyer belt to maximize productivity. A four DoF (Degree of Freedom) arm increases the working envelope and accessibility of painting different shaped parts with ease. This robot is capable of painting up, front, back, left and right sides of the part with a single colour. Initially CAD (Computer Aided Design) models of the robot were developed which were analyzed, modified and improved to withstand loading condition and perform its task efficiently. After design selection, appropriate motors and materials were selected and the robot was developed. Throughout the development phase, minor problems and errors were fixed accordingly as they arose. Lastly the robot was integrated with the computer and image processing for autonomous control. The final results demonstrated that the robot is economical and reduces paint wastage. (author)

  12. The Use of Circular Arc Cams for the Command of a Robotic System. Part II: Application to Knife Edge Translating Follower

    Directory of Open Access Journals (Sweden)

    Stelian Alaci

    2014-12-01

    Full Text Available In the second part of paper the results from the first part are applied to the cam mechanisms with knife-edge translating follower. First, a method for characterizing the tangency points fulfilling the actual constraints of the problem is identified. Applying this criterion, a set of equidistant points is generated on the whole geometrical locus of tangency points and the characteristics of approximating circles are found. Considering all replacement solutions, the kinematical analysis for all cam mechanisms with approximate profiles is made, choosing amid them the one performing the closest kinematical behavior to the exact cam mechanism.

  13. High-throughput mouse genotyping using robotics automation.

    Science.gov (United States)

    Linask, Kaari L; Lo, Cecilia W

    2005-02-01

    The use of mouse models is rapidly expanding in biomedical research. This has dictated the need for the rapid genotyping of mutant mouse colonies for more efficient utilization of animal holding space. We have established a high-throughput protocol for mouse genotyping using two robotics workstations: a liquid-handling robot to assemble PCR and a microfluidics electrophoresis robot for PCR product analysis. This dual-robotics setup incurs lower start-up costs than a fully automated system while still minimizing human intervention. Essential to this automation scheme is the construction of a database containing customized scripts for programming the robotics workstations. Using these scripts and the robotics systems, multiple combinations of genotyping reactions can be assembled simultaneously, allowing even complex genotyping data to be generated rapidly with consistency and accuracy. A detailed protocol, database, scripts, and additional background information are available at http://dir.nhlbi.nih.gov/labs/ldb-chd/autogene/.

  14. A trainlike vehicle for intervention missions inside nuclear plants

    International Nuclear Information System (INIS)

    Littmann, F.; Villedieu, E.; Chameaud, H.

    1992-01-01

    The Unite Robotique (part of the Direction of Advanced Technologies of Commissariat a l'Energie Atomique) has worked on nuclear robotics in the field of master/slave manipulators with their associated computer-aided teleoperation controls and mobile robots. The CENTAURE mobile robot is tracked (for stair climbing) and articulated (for obstacle crossing and turning on stair landings) with a mobile platform (for increasing stability), designed for inspection missions. For intervention missions, a vehicle is needed with larger payload capabilities (volume and mass) but with the same geometrical and environmental constraints. This paper deals with a new kind of trainlike vehicle designed for intervention missions inside nuclear facilities after an incident or accident. This idea was conceived in 1986 for the EUREKA program advanced mobile robot for civilian safety and is now entering a new phase with the TELEMAN program technology for advanced locomotion systems (in partnership with Kernforschungszentrum Karlsruhe for the locomotion and Cybernetix for the tests) with the building of a two-module linkage mockup and a locomotion mockup

  15. Springer handbook of robotics

    CERN Document Server

    Khatib, Oussama

    2016-01-01

    The second edition of this handbook provides a state-of-the-art cover view on the various aspects in the rapidly developing field of robotics. Reaching for the human frontier, robotics is vigorously engaged in the growing challenges of new emerging domains. Interacting, exploring, and working with humans, the new generation of robots will increasingly touch people and their lives. The credible prospect of practical robots among humans is the result of the scientific endeavour of a half a century of robotic developments that established robotics as a modern scientific discipline. The ongoing vibrant expansion and strong growth of the field during the last decade has fueled this second edition of the Springer Handbook of Robotics. The first edition of the handbook soon became a landmark in robotics publishing and won the American Association of Publishers PROSE Award for Excellence in Physical Sciences & Mathematics as well as the organization’s Award for Engineering & Technology. The second edition o...

  16. Project ROBOTICS 2008

    DEFF Research Database (Denmark)

    Conrad, Finn

    Mathematical modelling of Alto Robot, direct- and inverse kinematic transformation,simulation and path control applying MATLAB/SIMULINK.......Mathematical modelling of Alto Robot, direct- and inverse kinematic transformation,simulation and path control applying MATLAB/SIMULINK....

  17. CMS cavern inspection robot

    CERN Document Server

    Ibrahim, Ibrahim

    2017-01-01

    Robots which are immune to the CMS cavern environment, wirelessly controlled: -One actuated by smart materials (Ionic Polymer-Metal Composites and Macro Fiber Composites) -One regular brushed DC rover -One servo-driven rover -Stair-climbing robot

  18. The meaning of the EPSRC principles of robotics

    Science.gov (United States)

    Bryson, Joanna J.

    2017-04-01

    In revisiting the Principles of Robotics (as we do in this special issue), it is important to carefully consider their full meaning - their history, the intentions behind them, and their actual societal impact to date. Here I address first the meaning of the document as a whole, then of its constituent parts. Further, I describe the nature of policy, and use the Principles as a case study to discuss how government and academia can interact in constructing policy. I defend the Principles and their main themes: that commercially manufactured robots should not be responsible parties under the law, and that users should not be deceived about robots' capacities or moral status. This perspective allows for the incorporation of robots immediately into UK society and law - the objective of the Principles. The Principles were not designed for every conceivable robot, but rather serve in part as design specifications for robots to be incorporated as legal products into British society.

  19. ALLIANCE: An architecture for fault tolerant multi-robot cooperation

    International Nuclear Information System (INIS)

    Parker, L.E.

    1995-02-01

    ALLIANCE is a software architecture that facilitates the fault tolerant cooperative control of teams of heterogeneous mobile robots performing missions composed of loosely coupled, largely independent subtasks. ALLIANCE allows teams of robots, each of which possesses a variety of high-level functions that it can perform during a mission, to individually select appropriate actions throughout the mission based on the requirements of the mission, the activities of other robots, the current environmental conditions, and the robot's own internal states. ALLIANCE is a fully distributed, behavior-based architecture that incorporates the use of mathematically modeled motivations (such as impatience and acquiescence) within each robot to achieve adaptive action selection. Since cooperative robotic teams usually work in dynamic and unpredictable environments, this software architecture allows the robot team members to respond robustly, reliably, flexibly, and coherently to unexpected environmental changes and modifications in the robot team that may occur due to mechanical failure, the learning of new skills, or the addition or removal of robots from the team by human intervention. The feasibility of this architecture is demonstrated in an implementation on a team of mobile robots performing a laboratory version of hazardous waste cleanup

  20. RHOBOT: Radiation hardened robotics

    Energy Technology Data Exchange (ETDEWEB)

    Bennett, P.C.; Posey, L.D. [Sandia National Labs., Albuquerque, NM (United States)

    1997-10-01

    A survey of robotic applications in radioactive environments has been conducted, and analysis of robotic system components and their response to the varying types and strengths of radiation has been completed. Two specific robotic systems for accident recovery and nuclear fuel movement have been analyzed in detail for radiation hardness. Finally, a general design approach for radiation-hardened robotics systems has been developed and is presented. This report completes this project which was funded under the Laboratory Directed Research and Development program.

  1. Micro robot bible

    International Nuclear Information System (INIS)

    Yoon, Jin Yeong

    2000-08-01

    This book deals with micro robot, which tells of summary of robots like entertainment robots and definition of robots, introduction of micro mouse about history, composition and rules, summary of micro controller with its history, appearance and composition, introduction of stepping motor about types, structure, basic characteristics, and driving ways, summary of sensor section, power, understanding of 80C196KC micro controller, basic driving program searching a maze algorithm, smooth turn and making of tracer line.

  2. RHOBOT: Radiation hardened robotics

    International Nuclear Information System (INIS)

    Bennett, P.C.; Posey, L.D.

    1997-10-01

    A survey of robotic applications in radioactive environments has been conducted, and analysis of robotic system components and their response to the varying types and strengths of radiation has been completed. Two specific robotic systems for accident recovery and nuclear fuel movement have been analyzed in detail for radiation hardness. Finally, a general design approach for radiation-hardened robotics systems has been developed and is presented. This report completes this project which was funded under the Laboratory Directed Research and Development program

  3. Two Legged Walking Robot

    OpenAIRE

    Kraus, V.

    2015-01-01

    The aim of this work is to construct a two-legged wirelessly controlled walking robot. This paper describes the construction of the robot, its control electronics, and the solution of the wireless control. The article also includes a description of the application to control the robot. The control electronics of the walking robot are built using the development kit Arduino Mega, which is enhanced with WiFi module allowing the wireless control, a set of ultrasonic sensors for detecting obstacl...

  4. Micro robot bible

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, Jin Yeong

    2000-08-15

    This book deals with micro robot, which tells of summary of robots like entertainment robots and definition of robots, introduction of micro mouse about history, composition and rules, summary of micro controller with its history, appearance and composition, introduction of stepping motor about types, structure, basic characteristics, and driving ways, summary of sensor section, power, understanding of 80C196KC micro controller, basic driving program searching a maze algorithm, smooth turn and making of tracer line.

  5. Robots at Work

    OpenAIRE

    Graetz, Georg; Michaels, Guy

    2015-01-01

    Despite ubiquitous discussions of robots' potential impact, there is almost no systematic empirical evidence on their economic effects. In this paper we analyze for the first time the economic impact of industrial robots, using new data on a panel of industries in 17 countries from 1993-2007. We find that industrial robots increased both labor productivity and value added. Our panel identification is robust to numerous controls, and we find similar results instrumenting increased robot use wi...

  6. Robots in the Roses

    OpenAIRE

    2014-01-01

    2014-04 Robots in the Roses A CRUSER Sponsored Event. The 4th Annual Robots in the Roses provides a venue for Faculty & NPS Students to showcase unmanned systems research (current or completed) and recruit NPS Students to join in researching on your project. Posters, robots, vehicles, videos, and even just plain humans welcome! Families are welcome to attend Robots in the Roses as we'll have a STEM activity for children to participate in.

  7. Fully automated MRI-guided robotics for prostate brachytherapy

    International Nuclear Information System (INIS)

    Stoianovici, D.; Vigaru, B.; Petrisor, D.; Muntener, M.; Patriciu, A.; Song, D.

    2008-01-01

    The uncertainties encountered in the deployment of brachytherapy seeds are related to the commonly used ultrasound imager and the basic instrumentation used for the implant. An alternative solution is under development in which a fully automated robot is used to place the seeds according to the dosimetry plan under direct MRI-guidance. Incorporation of MRI-guidance creates potential for physiological and molecular image-guided therapies. Moreover, MRI-guided brachytherapy is also enabling for re-estimating dosimetry during the procedure, because with the MRI the seeds already implanted can be localised. An MRI compatible robot (MrBot) was developed. The robot is designed for transperineal percutaneous prostate interventions, and customised for fully automated MRI-guided brachytherapy. With different end-effectors, the robot applies to other image-guided interventions of the prostate. The robot is constructed of non-magnetic and dielectric materials and is electricity free using pneumatic actuation and optic sensing. A new motor (PneuStep) was purposely developed to set this robot in motion. The robot fits alongside the patient in closed-bore MRI scanners. It is able to stay fully operational during MR imaging without deteriorating the quality of the scan. In vitro, cadaver, and animal tests showed millimetre needle targeting accuracy, and very precise seed placement. The robot tested without any interference up to 7T. The robot is the first fully automated robot to function in MRI scanners. Its first application is MRI-guided seed brachytherapy. It is capable of automated, highly accurate needle placement. Extensive testing is in progress prior to clinical trials. Preliminary results show that the robot may become a useful image-guided intervention instrument. (author)

  8. Modular robot

    International Nuclear Information System (INIS)

    Ferrante, T.A.

    1997-01-01

    A modular robot may comprise a main body having a structure defined by a plurality of stackable modules. The stackable modules may comprise a manifold, a valve module, and a control module. The manifold may comprise a top surface and a bottom surface having a plurality of fluid passages contained therein, at least one of the plurality of fluid passages terminating in a valve port located on the bottom surface of the manifold. The valve module is removably connected to the manifold and selectively fluidically connects the plurality of fluid passages contained in the manifold to a supply of pressurized fluid and to a vent. The control module is removably connected to the valve module and actuates the valve module to selectively control a flow of pressurized fluid through different ones of the plurality of fluid passages in the manifold. The manifold, valve module, and control module are mounted together in a sandwich-like manner and comprise a main body. A plurality of leg assemblies are removably connected to the main body and are removably fluidically connected to the fluid passages in the manifold so that each of the leg assemblies can be selectively actuated by the flow of pressurized fluid in different ones of the plurality of fluid passages in the manifold. 12 figs

  9. Recovery of Proprioception in the Upper Extremity by Robotic Mirror Therapy: a Clinical Pilot Study for Proof of Concept.

    Science.gov (United States)

    Nam, Hyung Seok; Koh, Sukgyu; Beom, Jaewon; Kim, Yoon Jae; Park, Jang Woo; Koh, Eun Sil; Chung, Sun Gun; Kim, Sungwan

    2017-10-01

    A novel robotic mirror therapy system was recently developed to provide proprioceptive stimulus to the hemiplegic arm during a mirror therapy. Validation of the robotic mirror therapy system was performed to confirm its synchronicity prior to the clinical study. The mean error angle range between the intact arm and the robot was 1.97 to 4.59 degrees. A 56-year-old male who had right middle cerebral artery infarction 11 months ago received the robotic mirror therapy for ten 30-minute sessions during 2 weeks. Clinical evaluation and functional magnetic resonance imaging (fMRI) studies were performed before and after the intervention. At the follow-up evaluation, the thumb finding test score improved from 2 to 1 for eye level and from 3 to 1 for overhead level. The Albert's test score on the left side improved from 6 to 11. Improvements were sustained at 2-month follow-up. The fMRI during the passive motion revealed a considerable increase in brain activity at the lower part of the right superior parietal lobule, suggesting the possibility of proprioception enhancement. The robotic mirror therapy system may serve as a useful treatment method for patients with supratentorial stroke to facilitate recovery of proprioceptive deficit and hemineglect. © 2017 The Korean Academy of Medical Sciences.

  10. Clinical applications of robotic technology in vascular and endovascular surgery.

    Science.gov (United States)

    Antoniou, George A; Riga, Celia V; Mayer, Erik K; Cheshire, Nicholas J W; Bicknell, Colin D

    2011-02-01

    Emerging robotic technologies are increasingly being used by surgical disciplines to facilitate and improve performance of minimally invasive surgery. Robot-assisted intervention has recently been introduced into the field of vascular surgery to potentially enhance laparoscopic vascular and endovascular capabilities. The objective of this study was to review the current status of clinical robotic applications in vascular surgery. A systematic literature search was performed in order to identify all published clinical studies related to robotic implementation in vascular intervention. Web-based search engines were searched using the keywords "surgical robotics," "robotic surgery," "robotics," "computer assisted surgery," and "vascular surgery" or "endovascular" for articles published between January 1990 and November 2009. An evaluation and critical overview of these studies is reported. In addition, an analysis and discussion of supporting evidence for robotic computer-enhanced telemanipulation systems in relation to their applications in laparoscopic vascular and endovascular surgery was undertaken. Seventeen articles reporting on clinical applications of robotics in laparoscopic vascular and endovascular surgery were detected. They were either case reports or retrospective patient series and prospective studies reporting laparoscopic vascular and endovascular treatments for patients using robotic technology. Minimal comparative clinical evidence to evaluate the advantages of robot-assisted vascular procedures was identified. Robot-assisted laparoscopic aortic procedures have been reported by several studies with satisfactory results. Furthermore, the use of robotic technology as a sole modality for abdominal aortic aneurysm repair and expansion of its applications to splenic and renal artery aneurysm reconstruction have been described. Robotically steerable endovascular catheter systems have potential advantages over conventional catheterization systems

  11. Robotics research at Electrotechnical Laboratory-R and D program for advanced robot technology

    Energy Technology Data Exchange (ETDEWEB)

    Wakamatsu, S; Akahori, H; Shirai, Y; Kakikura, M

    1983-01-01

    The purposes of this paper are both to introduce the outline of robotics researches at Electrotechnical Laboratory and to describe the relation between those researches and the national project so called robotics for critical work. The authors first describe the robotics researches and related topics historically which have been continued from the latter half of 1960s as a part of researches on artificial intelligence at Electrotechnical Laboratory. Secondly, they mention the present aspects of our researches, its relation with past results, and changes of basic concepts on robotics systems. Finally, as an extension of our researches, they propose some approaches to establish the following techniques which make very important roles for the success of the national project; (1) manipulation techniques, (2) sensor techniques, (3) autonomous robot control techniques, (4) advanced tele-operation techniques and, (5) system totalizing techniques. 15 references.

  12. Investigation on Requirements of Robotic Platforms to Teach Social Skills to Individuals with Autism

    Science.gov (United States)

    Nikolopoulos, Chris; Kuester, Deitra; Sheehan, Mark; Dhanya, Sneha

    This paper reports on some of the robotic platforms used in the project AUROSO which investigates the use of robots as educationally useful interventions to improve social interactions for individuals with Autism Spectrum Disorders (ASD). Our approach to treatment uses an educational intervention based on Socially Assistive Robotics (SAR), the DIR/Floortime intervention model and social script/stories. Requirements are established and a variety of robotic models/platforms were investigated as to the feasibility of an economical, practical and efficient means of helping teach social skills to individuals with ASD for use by teachers, families, service providers and other community organizations.

  13. Building a Better Robot

    Science.gov (United States)

    Navah, Jan

    2012-01-01

    Kids love to build robots, letting their imaginations run wild with thoughts of what they might look like and what they could be programmed to do. Yet when students use cereal boxes and found objects to make robots, often the projects look too similar and tend to fall apart. This alternative allows students to "build" robots in a different way,…

  14. Open middleware for robotics

    CSIR Research Space (South Africa)

    Namoshe, M

    2008-12-01

    Full Text Available and their technologies within the field of multi-robot systems to ease the difficulty of realizing robot applications. And lastly, an example of algorithm development for multi-robot co-operation using one of the discussed software architecture is presented...

  15. Learning robotics using Python

    CERN Document Server

    Joseph, Lentin

    2015-01-01

    If you are an engineer, a researcher, or a hobbyist, and you are interested in robotics and want to build your own robot, this book is for you. Readers are assumed to be new to robotics but should have experience with Python.

  16. Robots de servicio

    Directory of Open Access Journals (Sweden)

    Rafael Aracil

    2008-04-01

    Full Text Available Resumen: El término Robots de Servicio apareció a finales de los años 80 como una necesidad de desarrollar máquinas y sistemas capaces de trabajar en entornos diferentes a los fabriles. Los Robots de Servicio tenían que poder trabajar en entornos noestructurados, en condiciones ambientales cambiantes y con una estrecha interacción con los humanos. En 1995 fue creado por la IEEE Robotics and Automation Society, el Technical Committee on Service Robots, y este comité definió en el año 2000 las áreas de aplicación de los Robots de Servicios, que se pueden dividir en dos grandes grupos: 1 sectores productivos no manufactureros tales como edificación, agricultura, naval, minería, medicina, etc. y 2 sectores de servicios propiamente dichos: asistencia personal, limpieza, vigilancia, educación, entretenimiento, etc. En este trabajo se hace una breve revisión de los principales conceptos y aplicaciones de los robots de servicio. Palabras clave: Robots de servicio, robots autónomos, robots de exteriores, robots de educación y entretenimiento, robots caminantes y escaladores, robots humanoides

  17. Beyond Speculative Robot Ethics

    NARCIS (Netherlands)

    Smits, M.; Van der Plas, A.

    2010-01-01

    In this article we develop a dialogue model for robot technology experts and designated users to discuss visions on the future of robotics in long-term care. Our vision assessment study aims for more distinguished and more informed visions on future robots. Surprisingly, our experiment also lead to

  18. Robotic hand and fingers

    Science.gov (United States)

    Salisbury, Curt Michael; Dullea, Kevin J.

    2017-06-06

    Technologies pertaining to a robotic hand are described herein. The robotic hand includes one or more fingers releasably attached to a robotic hand frame. The fingers can abduct and adduct as well as flex and tense. The fingers are releasably attached to the frame by magnets that allow for the fingers to detach from the frame when excess force is applied to the fingers.

  19. Real Time Indoor Robot Localization Using a Stationary Fisheye Camera

    OpenAIRE

    Delibasis , Konstantinos ,; Plagianakos , Vasilios ,; Maglogiannis , Ilias

    2013-01-01

    Part 7: Intelligent Signal and Image Processing; International audience; A core problem in robotics is the localization of a mobile robot (determination of the location or pose) in its environment, since the robot’s behavior depends on its position. In this work, we propose the use of a stationary fisheye camera for real time robot localization in indoor environments. We employ an image formation model for the fisheye camera, which is used for accelerating the segmentation of the robot’s top ...

  20. The Saskatchewan/New Brunswick Healthy Start-Départ Santé intervention: implementation cost estimates of a physical activity and healthy eating intervention in early learning centers.

    Science.gov (United States)

    Sari, Nazmi; Muhajarine, Nazeem; Froehlich Chow, Amanda

    2017-01-19

    Participation in daily physical activity and consuming a balanced diet high in fruits and vegetables and low in processed foods are behaviours associated with positive health outcomes during all stages of life. Previous literature suggests that the earlier these behaviours are established the greater the health benefits. As such, early learning settings have been shown to provide an effective avenue for exploring and influencing the physical activity and healthy eating behaviours of children before school entry. However, in addition to improving individual level health of children, such interventions may also result in a number of social benefits for the society. In fact, research among adult populations has shown that sufficient participation in physical activity can significantly lower hospital stays and physician visits, in turn leading to positive economic outcomes. To our knowledge there is very limited literature about economic evaluations of interventions implemented in early learning centers to increase physical activity and healthy eating behaviours among children. The primary purpose of this paper is to identify inputs and costs needed to implement a physical activity and healthy eating intervention (Healthy Start-Départ Santé (HS-DS)) in early learning centres throughout Saskatchewan and New Brunswick over the course of three years. In doing so, implementation cost is estimated to complete the first phase of a social return on investment analysis of this intervention. In order to carry out this evaluation the first step was to identify the inputs and costs needed to implement the intervention, along with the corresponding outputs. With stakeholder interviews and using existing database, we estimated the implementation cost by measuring, valuing and monetizing each individual input. Our results show that the total annual cost of implementing HS-DS was $378,753 in the first year, this total cost decreased slightly in the second year ($356,861) and again

  1. Anthropomorphic Robot Design and User Interaction Associated with Motion

    Science.gov (United States)

    Ellis, Stephen R.

    2016-01-01

    robot limbs and body positions, 2) improve users ability to detect anomalous robot behavior which could signal malfunction, and 3) enable users to be better able to infer the intent of robot movement. These three benefits of anthropomorphic design are inherent implications of the anthropomorphic form but they need to be recognized by designers as part of anthropomorphic design and explicitly enhanced to maximize their beneficial impact. Examples of such enhancements are provided in this report. If implemented, these benefits of anthropomorphic design can help reduce the risk of Inadequate Design of Human and Automation Robotic Integration (HARI) associated with the HARI-01 gap by providing efficient and dexterous operator control over robots and by improving operator ability to detect malfunctions and understand the intention of robot movement.

  2. Here today, gone tomorrow: biodegradable soft robots

    Science.gov (United States)

    Rossiter, Jonathan; Winfield, Jonathan; Ieropoulos, Ioannis

    2016-04-01

    One of the greatest challenges to modern technologies is what to do with them when they go irreparably wrong or come to the end of their productive lives. The convention, since the development of modern civilisation, is to discard a broken item and then procure a new one. In the 20th century enlightened environmentalists campaigned for recycling and reuse (R and R). R and R has continued to be an important part of new technology development, but there is still a huge problem of non-recyclable materials being dumped into landfill and being discarded in the environment. The challenge is even greater for robotics, a field which will impact on all aspects of our lives, where discards include motors, rigid elements and toxic power supplies and batteries. One novel solution is the biodegradable robot, an active physical machine that is composed of biodegradable materials and which degrades to nothing when released into the environment. In this paper we examine the potential and realities of biodegradable robotics, consider novel solutions to core components such as sensors, actuators and energy scavenging, and give examples of biodegradable robotics fabricated from everyday, and not so common, biodegradable electroactive materials. The realisation of truly biodegradable robots also brings entirely new deployment, exploration and bio-remediation capabilities: why track and recover a few large non-biodegradable robots when you could speculatively release millions of biodegradable robots instead? We will consider some of these exciting developments and explore the future of this new field.

  3. An inspection of pipe by snake robot

    Directory of Open Access Journals (Sweden)

    František Trebuňa

    2016-10-01

    Full Text Available The article deals with development and application of snake robot for inspection pipes. The first step involves the introduction of a design of mechanical and electrical parts of the snake robot. Next, the analysis of the robot locomotion is introduced. For the curved pipe, potential field method is used. By this method, the system is able to generate path for the head and rear robot, linking the environment with obstacles, which are represented by the walls of the pipe. Subsequently, the solution of potential field method is used in inverse kinematic model, which respects tasks as obstacle avoidance, joint limit avoidance, and singularity avoidance. Mentioned approach is then tested on snake robot in provisional pipe with rectangular cross section. For this research, software Matlab (2013b is used as the control system in cooperation with the control system of robot, which is based on microcontrollers. By experiments, it is shown that designed robot is able to pass through straight and also curved pipe.

  4. Robots could assist scientists working in Greenland

    Science.gov (United States)

    Showstack, Randy

    2011-07-01

    GREENLAND—Tom Lane and Suk Joon Lee, recent graduates of Dartmouth University's Thayer School of Engineering, in Hanover, N. H., are standing outside in the frigid cold testing an autonomous robot that could help with scientific research and logistics in harsh polar environments. This summer, Lane, Lee, and others are at Summit Station, a U.S. National Science Foundation (NSF)-sponsored scientific research station in Greenland, fine-tuning a battery-powered Yeti robot as part of a team working on the NSF-funded Cool Robot project. The station, also known as Summit Camp, is located on the highest point of the Greenland Ice Sheet (72°N, 38°W, 3200 meters above sea level) near the middle of the island. It is a proving ground this season for putting the approximately 68-kilogram, 1-cubic-meter robot through its paces, including improving Yeti's mobility capabilities and field-testing the robot. (See the electronic supplement to this Eos issue for a video of Yeti in action (http://www.agu.org/eos_elec/).) During field-testing, plans call for the robot to collect data on elevation and snow surface characteristics, including accumulation. In addition, the robot will collect black carbon and elemental carbon particulate matter air samples around Summit Camp's power generator to help study carbon dispersion over snow.

  5. A Fast Vision System for Soccer Robot

    Directory of Open Access Journals (Sweden)

    Tianwu Yang

    2012-01-01

    Full Text Available This paper proposes a fast colour-based object recognition and localization for soccer robots. The traditional HSL colour model is modified for better colour segmentation and edge detection in a colour coded environment. The object recognition is based on only the edge pixels to speed up the computation. The edge pixels are detected by intelligently scanning a small part of whole image pixels which is distributed over the image. A fast method for line and circle centre detection is also discussed. For object localization, 26 key points are defined on the soccer field. While two or more key points can be seen from the robot camera view, the three rotation angles are adjusted to achieve a precise localization of robots and other objects. If no key point is detected, the robot position is estimated according to the history of robot movement and the feedback from the motors and sensors. The experiments on NAO and RoboErectus teen-size humanoid robots show that the proposed vision system is robust and accurate under different lighting conditions and can effectively and precisely locate robots and other objects.

  6. Robotics and telecommunication systems to provide better access to ultrasound expertise in the OR.

    Science.gov (United States)

    Angelini, L; Papaspyropoulos, V

    2000-01-01

    Surgery has begun to evolve as a result of the intense use of technological innovations. The result of this is better services for patients and enormous opportunities for the producers of biomedical instruments. The surgeon and the technologist are fast becoming allies in applying the latest developments of robotics, image treatment, simulation, sensors and telecommunications to surgery, in particular to the emerging field of minimally-invasive surgery. Ultrasonography is at present utilised both for diagnostic and therapeutic purposes in various fields. Intraoperative US examination can be of primary importance, especially when dealing with space-occupying lesions. The widening use of minimally-invasive surgery has furthered the development of US for use during this type of surgery. The success of a US examination requires not only a correct execution of the procedure, but also a correct interpretation of the images. We describe two projects that combine robotics and telecommunication systems to provide better access to US expertise in the operating room. The Midstep project has as its object the realisation of two robotic arms, one for the distant control of the US probe during laparoscopic surgery and the second to perform tele-interventional US. The second project, part of the Strategic CNR Project-'Robotics in Surgery', involves the realisation of a common platform for tracking and targeting surgical instruments in video-assisted surgery.

  7. Reduction of robot base parameters

    Energy Technology Data Exchange (ETDEWEB)

    Vandanjon, P O [CEA Centre d` Etudes de Saclay, 91 - Gif-sur-Yvette (France). Dept. des Procedes et Systemes Avances; Gautier, M [Nantes Univ., 44 (France)

    1996-12-31

    This paper is a new step in the search of minimum dynamic parameters of robots. In spite of planing exciting trajectories and using base parameters, some parameters remain not identifiable due to the perturbation effects. In this paper, we propose methods to reduce the set of base parameters in order to get an essential set of parameters. This new set defines a simplified identification model witch improves the noise immunity of the estimation process. It contributes also in reducing the computation burden of a simplified dynamic model. Different methods are proposed and are classified in two parts: methods, witch perform reduction and identification together, come from statistical field and methods, witch reduces the model before the identification thanks to a priori information, come from numerical field like the QR factorization. Statistical tools and QR reduction are shown to be efficient and adapted to determine the essential parameters. They can be applied to open-loop, or graph structured rigid robot, as well as flexible-link robot. Application for the PUMA 560 robot is given. (authors). 9 refs., 4 tabs.

  8. Reduction of robot base parameters

    International Nuclear Information System (INIS)

    Vandanjon, P.O.

    1995-01-01

    This paper is a new step in the search of minimum dynamic parameters of robots. In spite of planing exciting trajectories and using base parameters, some parameters remain not identifiable due to the perturbation effects. In this paper, we propose methods to reduce the set of base parameters in order to get an essential set of parameters. This new set defines a simplified identification model witch improves the noise immunity of the estimation process. It contributes also in reducing the computation burden of a simplified dynamic model. Different methods are proposed and are classified in two parts: methods, witch perform reduction and identification together, come from statistical field and methods, witch reduces the model before the identification thanks to a priori information, come from numerical field like the QR factorization. Statistical tools and QR reduction are shown to be efficient and adapted to determine the essential parameters. They can be applied to open-loop, or graph structured rigid robot, as well as flexible-link robot. Application for the PUMA 560 robot is given. (authors). 9 refs., 4 tabs

  9. Can Robotic Interaction Improve Joint Attention Skills?

    Science.gov (United States)

    Warren, Zachary E.; Zheng, Zhi; Swanson, Amy R.; Bekele, Esubalew; Zhang, Lian; Crittendon, Julie A.; Weitlauf, Amy F.; Sarkar, Nilanjan

    2015-01-01

    Although it has often been argued that clinical applications of advanced technology may hold promise for addressing impairments associated with autism spectrum disorder (ASD), relatively few investigations have indexed the impact of intervention and feedback approaches. This pilot study investigated the application of a novel robotic interaction…

  10. Development of an exercise intervention as part of rehabilitation in a glioblastoma multiforme survivor during irradiation treatment

    DEFF Research Database (Denmark)

    Hansen, Anders; Søgaard, Karen; Minet, Lisbeth Rosenbek

    2018-01-01

    completed a supervised six-week exercise intervention during irradiation treatment beginning 42 d after resection. Exercise modalities of cardiorespiratory, resistance, and balance training were designed on generic recommendations of various cancer populations and literature review. RESULTS: Our case...... attended all possible sessions without experiencing adverse effects, and improved in aerobe power (24%), muscle strength (0-38%), standing balance (71%), walking ability (9%), and QOL domains of "Global Health Status/QoL" and "Physical functioning." CONCLUSIONS: Based on this single case, exercise...

  11. Development of an internet version of the Lidcombe Program of early stuttering intervention: A trial of Part 1.

    Science.gov (United States)

    Van Eerdenbrugh, Sabine; Packman, Ann; Onslow, Mark; O'brian, Sue; Menzies, Ross

    2018-04-01

    There is evidence that access to treatment for early stuttering is not available for all who need it. An internet version of the Lidcombe Program for early stuttering (Internet-LP) has been developed to deal with this shortfall. The LP is suitable for such development because it is delivered by parents in the child's everyday environment, with training by a speech-language pathologist. A Phase I trial of Internet-LP Part 1, comprising parent training, is reported here. Eight parents of pre-schoolers who stutter were recruited and six completed the trial. Post-trial assessment indicated that the parents scored well for identifying and measuring stuttering and for knowledge about conducting practice sessions, including how to present verbal contingencies during practice sessions. The results prompted minor adjustments to Part 1 and guided the construction of Part 2, which instructs parents during the remainder of the treatment process.

  12. [Robotics in pediatric surgery].

    Science.gov (United States)

    Camps, J I

    2011-10-01

    Despite the extensive use of robotics in the adult population, the use of robotics in pediatrics has not been well accepted. There is still a lack of awareness from pediatric surgeons on how to use the robotic equipment, its advantages and indications. Benefit is still controversial. Dexterity and better visualization of the surgical field are one of the strong values. Conversely, cost and a lack of small instruments prevent the use of robotics in the smaller patients. The aim of this manuscript is to present the controversies about the use of robotics in pediatric surgery.

  13. Low cost submarine robot

    Directory of Open Access Journals (Sweden)

    Ponlachart Chotikarn

    2010-10-01

    Full Text Available A submarine robot is a semi-autonomous submarine robot used mainly for marine environmental research. We aim todevelop a low cost, semi-autonomous submarine robot which is able to travel underwater. The robot’s structure was designedand patented using a novel idea of the diving system employing a volume adjustment mechanism to vary the robot’s density.A light weight, flexibility and small structure provided by PVC can be used to construct the torpedo-liked shape robot.Hydraulic seal and O-ring rubbers are used to prevent water leaking. This robot is controlled by a wired communicationsystem.

  14. Advances in robot kinematics

    CERN Document Server

    Khatib, Oussama

    2014-01-01

    The topics addressed in this book cover the whole range of kinematic analysis, synthesis and design and consider robotic systems possessing serial, parallel and cable driven mechanisms. The robotic systems range from being less than fully mobile to kinematically redundant to overconstrained.  The fifty-six contributions report the latest results in robot kinematics with emphasis on emerging areas such as design and control of humanoids or humanoid subsystems. The book is of interest to researchers wanting to bring their knowledge up to date regarding modern topics in one of the basic disciplines in robotics, which relates to the essential property of robots, the motion of mechanisms.

  15. Ask a Futurist. Peace [and] Robots.

    Science.gov (United States)

    Joseph, Earl C.

    A futurist addresses two questions concerning world peace and the implications of using robots. In the section on peace (part 1), recommendations for world peace include: (1) implementing peace education as a mandatory part of education; (2) establishing a Department of Peace in each country to create a societal infrastructure for implementing…

  16. Robotic inspection technology-process an toolbox

    Energy Technology Data Exchange (ETDEWEB)

    Hermes, Markus [ROSEN Group (United States). R and D Dept.

    2005-07-01

    Pipeline deterioration grows progressively with ultimate aging of pipeline systems (on-plot and cross country). This includes both, very localized corrosion as well as increasing failure probability due to fatigue cracking. Limiting regular inspecting activities to the 'scrapable' part of the pipelines only, will ultimately result into a pipeline system with questionable integrity. The confidence level in the integrity of these systems will drop below acceptance levels. Inspection of presently un-inspectable sections of the pipeline system becomes a must. This paper provides information on ROSEN's progress on the 'robotic inspection technology' project. The robotic inspection concept developed by ROSEN is based on a modular toolbox principle. This is mandatory. A universal 'all purpose' robot would not be reliable and efficient in resolving the postulated inspection task. A preparatory Quality Function Deployment (QFD) analysis is performed prior to the decision about the adequate robotic solution. This enhances the serviceability and efficiency of the provided technology. The word 'robotic' can be understood in its full meaning of Recognition - Strategy - Motion - Control. Cooperation of different individual systems with an established communication, e.g. utilizing Bluetooth technology, support the robustness of the ROSEN robotic inspection approach. Beside the navigation strategy, the inspection strategy is also part of the QFD process. Multiple inspection technologies combined on a single carrier or distributed across interacting container must be selected with a clear vision of the particular goal. (author)

  17. Robotic surgery in Italy national survey (2011).

    Science.gov (United States)

    Santoro, Eugenio; Pansadoro, Vito

    2013-03-01

    Robotic surgery in Italy has become a clinical reality that is gaining increasing acceptance. As of 2011 after the United States, Italy together with Germany is the country with the largest number of active Robotic centers, 46, and da Vinci Robots installed, with at least 116 operators already trained. The number of interventions performed in Italy in 2011 exceeded 6,000 and in 2010 were 4,784, with prevalence for urology, general surgery and gynecology, however these interventions have also begun to be applied in other fields such as cervicofacial, cardiothoracic and pediatric surgery. In Italy Robotic centers are mostly located in Northern Italy, while in the South there are only a few centers, and four regions are lacking altogether. Of the 46 centers which were started in 1999, the vast majority is still operational and almost half handle over 200 cases a year. The quality of the work is also especially high with large diffusion of radical prostatectomy in urology and liver resection and colic in general surgery. The method is very well accepted among operators, over 80 %, and among patients, over 95 %. From the analysis of world literature and a survey carried out in Italy, Robotic surgery, which at the moment could be better defined as telesurgery, represents a significant advantage for operators and a consistent gain for the patient. However, it still has important limits such as high cost and non-structured training of operators.

  18. Robot technology

    International Nuclear Information System (INIS)

    Vertut, Jean; Coiffet, Philippe.

    1985-01-01

    Teleoperation is concerned with the exploration and exploitation of of spaces which do not allow, because of their inaccessibility or hostility, direct access to man. This volume (Parts 2, 3 and 4) covers the contribution of computer science and automatic control to this technology. Part 2 includes a description of teleoperation systems followed by chapters on the operator substitution function by computer feedback to the operator. Part 3 has chapters on performance evaluation of teleoperation systems and the human operator in the teleoperation system. Part 4 is about applications of teleoperation in the nuclear industry, underwater, in space, in medicine, in industry and in security and civil protection. The nuclear applications include research and pilot facilities, reactor operation and maintenance, reactor decommissioning and dismantling and in emergencies, for example following a reactor accident. (U.K.)

  19. Marine Robot Autonomy

    CERN Document Server

    2013-01-01

    Autonomy for Marine Robots provides a timely and insightful overview of intelligent autonomy in marine robots. A brief history of this emerging field is provided, along with a discussion of the challenges unique to the underwater environment and their impact on the level of intelligent autonomy required.  Topics covered at length examine advanced frameworks, path-planning, fault tolerance, machine learning, and cooperation as relevant to marine robots that need intelligent autonomy.  This book also: Discusses and offers solutions for the unique challenges presented by more complex missions and the dynamic underwater environment when operating autonomous marine robots Includes case studies that demonstrate intelligent autonomy in marine robots to perform underwater simultaneous localization and mapping  Autonomy for Marine Robots is an ideal book for researchers and engineers interested in the field of marine robots.      

  20. Geometric design of part feeders

    NARCIS (Netherlands)

    Berretty, R.-P.M.

    2000-01-01

    This thesis presents solutions for problems derived from industrial assembly and robotic manipulation. The basic tasks in a factory are manufacturing the parts, and combining them into the desired product. In automating these tasks, we want to use robot manipulators that require little or no

  1. Research project RoboGas{sup Inspector}. Gas leak detection with autonomous mobile robots; Forschungsprojekt RoboGas{sup Inspector}. Gaslecksuche mit autonomen mobilen Robotern

    Energy Technology Data Exchange (ETDEWEB)

    Habib, Abdelkarim [BAM Bundesanstalt fuer Materialforschung und -pruefung, Berlin (Germany); Bonow, Gero; Kroll, Andreas [Fachgebiet Mess- und Regelungstechnik, Universitaet Kassel, Kassel (Germany); Hegenberg, Jens; Schmidt, Ludger [Fachgebiet Mensch-Maschine-Systemtechnik, Universitaet Kassel, Kassel (Germany); Barz, Thomas; Schulz, Dirk [Fraunhofer FKIE, Unbemannte Systeme, Wachtberg (Germany)

    2013-05-15

    As part of the promotional program AUTONOMIK of the Federal Ministry of Economics and Technology (Berlin, Federal Republic of Germany) a consortium of nine project partners developed a prototype of an autonomous mobile robot looking for gas leaks in extended industrial equipment. The autonomous mobility of the system for any systems was implemented using different types of sensors for self-localization and navigation. The tele-operation enables a manual intervention in the process. The robot performs inspection tasks in industrial plants by means of video technology and remote gas measurement technology without driving into the possible risk areas and without the presence of humans. The robot can be used for routine inspections of facilities or for the targeted inspection of specific plant components. Thanks to the remote sensing technique also plant components can be inspected which are difficult to be inspected due to their limited accessibility by conventional measurement techniques.

  2. Future robotic platforms in urologic surgery: Recent Developments

    Science.gov (United States)

    Herrell, S. Duke; Webster, Robert; Simaan, Nabil

    2014-01-01

    Purpose of review To review recent developments at Vanderbilt University of new robotic technologies and platforms designed for minimally invasive urologic surgery and their design rationale and potential roles in advancing current urologic surgical practice. Recent findings Emerging robotic platforms are being developed to improve performance of a wider variety of urologic interventions beyond the standard minimally invasive robotic urologic surgeries conducted presently with the da Vinci platform. These newer platforms are designed to incorporate significant advantages of robotics to improve the safety and outcomes of transurethral bladder surgery and surveillance, further decrease the invasiveness of interventions by advancing LESS surgery, and allow for previously impossible needle access and ablation delivery. Summary Three new robotic surgical technologies that have been developed at Vanderbilt University are reviewed, including a robotic transurethral system to enhance bladder surveillance and TURBT, a purpose-specific robotic system for LESS, and a needle sized robot that can be used as either a steerable needle or small surgeon-controlled micro-laparoscopic manipulator. PMID:24253803

  3. College of Engineering team to build battlefield robots for 2010 competition

    OpenAIRE

    Mackay, Steven D.

    2010-01-01

    The roving, walking robotic soldiers of the "Terminator" films are becoming less sci-fi, and more certain future every day. Now, a team of robotics researchers from the Virginia Tech College of Engineering will build a team of fully autonomous cooperative battle-ready robots as part of a 2010 international war games challenge that could spur real-life battle bots.

  4. Advanced robot vision system for nuclear power plants

    International Nuclear Information System (INIS)

    Onoguchi, Kazunori; Kawamura, Atsuro; Nakayama, Ryoichi.

    1991-01-01

    We have developed a robot vision system for advanced robots used in nuclear power plants, under a contract with the Agency of Industrial Science and Technology of the Ministry of International Trade and Industry. This work is part of the large-scale 'advanced robot technology' project. The robot vision system consists of self-location measurement, obstacle detection, and object recognition subsystems, which are activated by a total control subsystem. This paper presents details of these subsystems and the experimental results obtained. (author)

  5. Navigating the pathway to robotic competency in general thoracic surgery.

    Science.gov (United States)

    Seder, Christopher W; Cassivi, Stephen D; Wigle, Dennis A

    2013-01-01

    Although robotic technology has addressed many of the limitations of traditional videoscopic surgery, robotic surgery has not gained widespread acceptance in the general thoracic community. We report our initial robotic surgery experience and propose a structured, competency-based pathway for the development of robotic skills. Between December 2008 and February 2012, a total of 79 robot-assisted pulmonary, mediastinal, benign esophageal, or diaphragmatic procedures were performed. Data on patient characteristics and perioperative outcomes were retrospectively collected and analyzed. During the study period, one surgeon and three residents participated in a triphasic, competency-based pathway designed to teach robotic skills. The pathway consisted of individual preclinical learning followed by mentored preclinical exercises and progressive clinical responsibility. The robot-assisted procedures performed included lung resection (n = 38), mediastinal mass resection (n = 19), hiatal or paraesophageal hernia repair (n = 12), and Heller myotomy (n = 7), among others (n = 3). There were no perioperative mortalities, with a 20% complication rate and a 3% readmission rate. Conversion to a thoracoscopic or open approach was required in eight pulmonary resections to facilitate dissection (six) or to control hemorrhage (two). Fewer major perioperative complications were observed in the later half of the experience. All residents who participated in the thoracic surgery robotic pathway perform robot-assisted procedures as part of their clinical practice. Robot-assisted thoracic surgery can be safely learned when skill acquisition is guided by a structured, competency-based pathway.

  6. Design and Optimization of Intelligent Service Robot Suspension System Using Dynamic Model

    International Nuclear Information System (INIS)

    Choi, Seong Hoon; Park, Tae Won; Lee, Soo Ho; Jung, Sung Pil; Jun, Kab Jin; Yoon, J. W.

    2010-01-01

    Recently, an intelligent service robot is being developed for use in guiding and providing information to visitors about the building at public institutions. The intelligent robot has a sensor at the bottom to recognize its location. Four wheels, which are arranged in the form of a lozenge, support the robot. This robot cannot be operated on uneven ground because its driving parts are attached to its main body that contains the important internal components. Continuous impact with the ground can change the precise positions of the components and weaken the connection between each structural part. In this paper, the design of the suspension system for such a robot is described. The dynamic model of the robot is created, and the driving characteristics of the robot with the designed suspension system are simulated. Additionally, the suspension system is optimized to reduce the impact for the robot components

  7. Robotic Toys as a Catalyst for Mathematical Problem Solving

    Science.gov (United States)

    Highfield, Kate

    2010-01-01

    Robotic toys present unique opportunities for teachers of young children to integrate mathematics learning with engaging problem-solving tasks. This article describes a series of tasks using Bee-bots and Pro-bots, developed as part a larger project examining young children's use of robotic toys as tools in developing mathematical and metacognitive…

  8. Remote control and motion coordination of mobile robots

    NARCIS (Netherlands)

    Alvarez Aguirre, A.

    2011-01-01

    As robots destined for personal and professional applications advance towards becoming part of our daily lives, the importance and complexity of the control algorithms which regulate them should not be underestimated. This thesis is related to two fields within robotics which are of major importance

  9. Centralised versus Decentralised Control Reconfiguration for Collaborating Underwater Robots

    DEFF Research Database (Denmark)

    Furno, Lidia; Nielsen, Mikkel Cornelius; Blanke, Mogens

    2015-01-01

    The present paper introduces an approach to fault-tolerant reconfiguration for collaborating underwater robots. Fault-tolerant reconfiguration is obtained using the virtual actuator approach, Steen (2005). The paper investigates properties of a centralised versus a decentralised implementation an...... an underwater drill needs to be transported and positioned by three collaborating robots as part of an underwater autonomous operation....

  10. ASBESTOS PIPE-INSULATION REMOVAL ROBOT SYSTEM; FINAL

    International Nuclear Information System (INIS)

    Unknown

    2000-01-01

    This final topical report details the development, experimentation and field-testing activities for a robotic asbestos pipe-insulation removal robot system developed for use within the DOE's weapon complex as part of their ER and WM program, as well as in industrial abatement. The engineering development, regulatory compliance, cost-benefit and field-trial experiences gathered through this program are summarized

  11. MART: an overview of the Mobile Autonomous Robot Twente project

    NARCIS (Netherlands)

    Tillema, H.G.; de Graaf, A.J.; Koster, M.P.; Nauta, J.M.; Oelen, W.; Schipper, D.A.

    1993-01-01

    At the University of Twente a mobile autonomous robot system is built that is designed to operate in a 'factory of the future'. Multiple robots, consisting of a manipulator on top of a vehicle, will drive through an assembly hall to collect components at part supply stations and to assemble

  12. Training modalities in robot-mediated upper limb rehabilitation in stroke: a framework for classification based on a systematic review

    NARCIS (Netherlands)

    Basteris, A.; Nijenhuis, S.M.; Stienen, Arno; Buurke, Jaap; Prange, Grada Berendina; Amirabdollahian, F

    2014-01-01

    Robot-mediated post-stroke therapy for the upper-extremity dates back to the 1990s. Since then, a number of robotic devices have become commercially available. There is clear evidence that robotic interventions improve upper limb motor scores and strength, but these improvements are often not

  13. 11th International Symposium on Distributed Autonomous Robotic Systems

    CERN Document Server

    Chirikjian, Gregory

    2014-01-01

    Distributed robotics is a rapidly growing and maturing interdisciplinary research area lying at the intersection of computer science, network science, control theory, and electrical and mechanical engineering. The goal of the Symposium on Distributed Autonomous Robotic Systems (DARS) is to exchange and stimulate research ideas to realize advanced distributed robotic systems. This volume of proceedings includes 31 original contributions presented at the 2012 International Symposium on Distributed Autonomous Robotic Systems (DARS 2012) held in November 2012 at the Johns Hopkins University in Baltimore, MD USA. The selected papers in this volume are authored by leading researchers from Asia, Europa, and the Americas, thereby providing a broad coverage and perspective of the state-of-the-art technologies, algorithms, system architectures, and applications in distributed robotic systems. The book is organized into five parts, representative of critical long-term and emerging research thrusts in the multi-robot com...

  14. New trends in medical and service robots challenges and solutions

    CERN Document Server

    Pisla, Doina; Bleuler, Hannes

    2014-01-01

    This volume describes new frontiers in medical and service robotics in the light of recent developments in technology to advance robot design and implementation. In particular, the work looks at advances in design, development and implementation of contemporary surgical, rehabilitation and biorobots. Surgical robots allow surgeons greater access to areas under operation using more precise and less invasive methods. Rehabilitation robots facilitate and support the lives of the infirm, elderly people, or those with dysfunction of body parts affecting movement. These robots are also used for rehabilitation and related procedures, such as training and therapy. Biorobots are designed to imitate the cognition of humans and animals. The need to substitute humans working on delicate, tiresome and monotonous tasks, or working with potentially health-damaging toxic materials, requires intelligent, high-performance service robots with the ability to cooperate, advanced communication and sophisticated perception and cogn...

  15. Simulated Energy Usage for a Novel 6 DOF Articulated Robot

    International Nuclear Information System (INIS)

    Shaik, A A; Tlale, N; Bright, G

    2014-01-01

    The serial robot architecture is widespread in modern day manufacturing, and over the last few decades the technology has matured and settled to its current state. One drawback from the architecture however is the location of motors and gearboxes which are either at the joint it controls or close by. A novel hybrid 6 DOF robot was designed to move all the actuators to the robot base, and to control the desired axis through a set of connected links and gears, while maintaining the same workspace and dexterity. This would reduce the inertia of the movable part of the robot and some of the moment arms on the 3 axes required for translation of the 3 DOF spherical wrist. Doing so would decrease the energy requirements when compared to a 6 DOF serial robot. This paper focuses on the mathematical modelling and simulation of the novel hybrid machine design and compares it to an equivalent serial robot

  16. Robotic Approach in Benign and Malignant Esophageal Tumors; A Preliminary Seven Case Series.

    Science.gov (United States)

    Tomulescu, Victor; Stanescu, Codrut; Blajut, Cristian; Barbulescu, Loredana; Droc, Gabriela; Herlea, Vlad; Popescu, Irinel

    2018-01-01

    Esophageal surgery has been recognized as very challenging for surgeons and risky for patients. Thoracoscopic approach have proved its benefit in esophageal surgery but has some drawbacks as tremor and limited degrees of freedom, contra-intuitive movements and fulcrum effect of the surgical tools. Robotic technology has been developed with the intent to overcome these limitations of the standard laparoscopy or thoracoscopy. These benefits of robotic procedure are most advantageous when operating in remote areas difficult to reach as in esophageal surgery. The aim of this paper is to present our small experience related with robotic approach in benign and malignant esophageal tumors and critically revise the evidence available about the use of the robotic technology for the treatment of these pathology. Methods: From January 2008 to September 2016 robotic surgery interventions related with benign or malignant esophageal tumors were performed in "Dan Setlacec" Center for General Surgery and Liver Transplantation of Fundeni Clinical Institute in seven patients. This consisted of dissection of the entire esophagus as part of an abdomino-thoracic-cervical procedure for esophageal cancer in 3 patients and the extirpation of an esophageal leiomyoma in 3 cases and a foregut esophageal cyst in one case. Results: All procedures except one were completed entirely using the da Vinci robotic system. The exception was the first case - a 3 cm leiomyoma of the inferior esophagus with ulceration of the superjacent esophageal mucosa. Pathology reports revealed three esophageal leiomyoma, one foregut cyst and three squamous cell carcinomas with free of tumor resection margins. The mean number of retrieved mediastinal nodes was 24 (22 - 27). The postoperative course was uneventful in four cases, in the other three a esophageal fistula occurred in the converted leiomyoma case (closed in the 14th postoperative day), a prolonged drainage in one esophageal cancer case and a temporary

  17. Orthotic intervention incorporating the dart-thrower's motion as part of conservative management guidelines for treatment of scapholunate injury.

    Science.gov (United States)

    Anderson, Hamish; Hoy, Greg

    2016-01-01

    Case series. This paper describes conservative guidelines for the management of scapho-lunate interosseous ligament (SLIL) injury including fabrication of an orthosis that restricts active wrist movement to the dart-throwers (DTM) plane. The dart throwers' orthosis (DTO) was designed as a response to biomechanical studies suggesting that restraining motion to the DTM would off-load a deficient SLIL. After six weeks of wearing the DTO, the 5 patients in this case series initiated an exercise program that incorporated wrist proprioceptive training and specific muscle strengthening. The DTO was designed to incorporate controlled movement in order to better integrate the secondary wrist stabilizers in wrists that had a deficient SLIL. The orthosis and the exercise program harnessed proprioceptive influences using active motion within the DTM plane, and stimulated mechanoreceptors so as to enhance stability. All patients demonstrated improvement in subjective and objective outcomes including self-reported pain and function. Orthotic intervention that controls motion within the DTM, combined with an appropriate proprioceptive rehabilitation program, may provide a viable conservative treatment option for patients with a similar clinical presentation. 4. Copyright © 2016 Hanley & Belfus. Published by Elsevier Inc. All rights reserved.

  18. Non-manufacturing applications of robotics

    International Nuclear Information System (INIS)

    Dauchez, P.

    2000-12-01

    This book presents the different non-manufacturing sectors of activity where robotics can have useful or necessary applications: underwater robotics, agriculture robotics, road work robotics, nuclear robotics, medical-surgery robotics, aids to disabled people, entertainment robotics. Service robotics has been voluntarily excluded because this developing sector is not mature yet. (J.S.)

  19. Evolution of robotic arms.

    Science.gov (United States)

    Moran, Michael E

    2007-01-01

    The foundation of surgical robotics is in the development of the robotic arm. This is a thorough review of the literature on the nature and development of this device with emphasis on surgical applications. We have reviewed the published literature and classified robotic arms by their application: show, industrial application, medical application, etc. There is a definite trend in the manufacture of robotic arms toward more dextrous devices, more degrees-of-freedom, and capabilities beyond the human arm. da Vinci designed the first sophisticated robotic arm in 1495 with four degrees-of-freedom and an analog on-board controller supplying power and programmability. von Kemplen's chess-playing automaton left arm was quite sophisticated. Unimate introduced the first industrial robotic arm in 1961, it has subsequently evolved into the PUMA arm. In 1963 the Rancho arm was designed; Minsky's Tentacle arm appeared in 1968, Scheinman's Stanford arm in 1969, and MIT's Silver arm in 1974. Aird became the first cyborg human with a robotic arm in 1993. In 2000 Miguel Nicolalis redefined possible man-machine capacity in his work on cerebral implantation in owl-monkeys directly interfacing with robotic arms both locally and at a distance. The robotic arm is the end-effector of robotic systems and currently is the hallmark feature of the da Vinci Surgical System making its entrance into surgical application. But, despite the potential advantages of this computer-controlled master-slave system, robotic arms have definite limitations. Ongoing work in robotics has many potential solutions to the drawbacks of current robotic surgical systems.

  20. Presence of Life-Like Robot Expressions Influences Children’s Enjoyment of Human-Robot Interactions in the Field

    NARCIS (Netherlands)

    Cameron, David; Fernando, Samuel; Collins, Emily; Millings, Abigail; Moore, Roger; Sharkey, Amanda; Evers, Vanessa; Prescott, Tony

    Emotions, and emotional expression, have a broad influence on the interactions we have with others and are thus a key factor to consider in developing social robots. As part of a collaborative EU project, this study examined the impact of lifelike affective facial expressions, in the humanoid robot

  1. Design and Development of Mechanical Structure and Control System for Tracked Trailing Mobile Robot

    OpenAIRE

    Hongchuan Xu; Jianxing Ren; Rui Zhu; Zhiwei Chen

    2013-01-01

    Along with the science and technology unceasing progress, the uses of tracing robots become more and more widely. Tracked tracing robot was adopted as the research object in this paper, mechanical structure and control system of robot was designed and developmented. In mechanical structure design part, structure designed and positioned  were completed, including design of robot body, wheel, underpan, transmission structure and the positioning of batteries, control panel, sensors, etc, and the...

  2. Node Primitives: an open end-user programming platform for social robots

    OpenAIRE

    Coronado, Enrique; Mastrogiovanni, Fulvio; Venture, Gentiane

    2017-01-01

    With the expected adoption of robots able to seamlessly and intuitively interact with people in real-world scenarios, the need arises to provide non-technically-skilled users with easy-to-understand paradigms for customising robot behaviors. In this paper, we present an interaction design robot programming platform for enabling multidisciplinary social robot research and applications. This platform is referred to Node Primitives (NEP) and consists of two main parts. On the one hand, a ZeroMQ ...

  3. Affordable mobile robotic platforms for teaching computer science at African universities

    OpenAIRE

    Gyebi, Ernest; Hanheide, Marc; Cielniak, Grzegorz

    2015-01-01

    Educational robotics can play a key role in addressing some of the challenges faced by higher education in Africa. One of the major obstacles preventing a wider adoption of initiatives involving educational robotics in this part of the world is lack of robots that would be affordable by African institutions. In this paper, we present a survey and analysis of currently available affordable mobile robots and their suitability for teaching computer science at African universities. To this end, w...

  4. Comparison of Perioperative Outcomes of Total Laparoscopic and Robotically Assisted Hysterectomy for Benign Pathology during Introduction of a Robotic Program

    Directory of Open Access Journals (Sweden)

    Gokhan Sami Kilic

    2011-01-01

    Full Text Available Study Objective. Prospectively compare outcomes of robotically assisted and laparoscopic hysterectomy in the process of implementing a new robotic program. Design. Prospectively comparative observational nonrandomized study. Design Classification. II-1. Setting. Tertiary caregiver university hospital. Patients. Data collected consecutively 24 months, 34 patients underwent laparoscopic hysterectomy, 25 patients underwent robotic hysterectomy, and 11 patients underwent vaginal hysterectomy at our institution. Interventions. Outcomes of robotically assisted, laparoscopic, and vaginal complex hysterectomies performed by a single surgeon for noncancerous indications. Measurements and Main Results. Operative times were 208.3±59.01 minutes for laparoscopic, 286.2±82.87 minutes for robotic, and 163.5±61.89 minutes for vaginal (<.0001. Estimated blood loss for patients undergoing laparoscopic surgery was 242.7±211.37 cc, 137.4±107.50 cc for robotic surgery, and 243.2±127.52 cc for vaginal surgery (=0.05. The mean length of stay ranged from 1.8 to 2.3 days for the 3 methods. Association was significant for uterine weight (=0.0043 among surgery methods. Conclusion. Robotically assisted hysterectomy is feasible with low morbidity, a shorter hospital stay, and less blood loss. This suggests that robotic assistance facilitates a minimally invasive approach for patients with larger uterine size even during implementing a new robotic program.

  5. Smooth leader or sharp follower? Playing the mirror game with a robot.

    Science.gov (United States)

    Kashi, Shir; Levy-Tzedek, Shelly

    2018-01-01

    The increasing number of opportunities for human-robot interactions in various settings, from industry through home use to rehabilitation, creates a need to understand how to best personalize human-robot interactions to fit both the user and the task at hand. In the current experiment, we explored a human-robot collaborative task of joint movement, in the context of an interactive game. We set out to test people's preferences when interacting with a robotic arm, playing a leader-follower imitation game (the mirror game). Twenty two young participants played the mirror game with the robotic arm, where one player (person or robot) followed the movements of the other. Each partner (person and robot) was leading part of the time, and following part of the time. When the robotic arm was leading the joint movement, it performed movements that were either sharp or smooth, which participants were later asked to rate. The greatest preference was given to smooth movements. Half of the participants preferred to lead, and half preferred to follow. Importantly, we found that the movements of the robotic arm primed the subsequent movements performed by the participants. The priming effect by the robot on the movements of the human should be considered when designing interactions with robots. Our results demonstrate individual differences in preferences regarding the role of the human and the joint motion path of the robot and the human when performing the mirror game collaborative task, and highlight the importance of personalized human-robot interactions.

  6. Is Ethics of Robotics about Robots? Philosophy of Robotics Beyond Realism and Individualilsm.

    NARCIS (Netherlands)

    Coeckelbergh, Mark

    2011-01-01

    If we are doing ethics of robotics, what exactly is the object of our inquiry? This paper challenges 'individualist' robot ontology and 'individualist' social philosophy of robots. It is argued that ethics of robotics should not study and evaluate robotics exclusively in terms of individual

  7. Robotic mounting of ATLAS barrel SCT modules

    International Nuclear Information System (INIS)

    Nickerson, R.B.; Viehhauser, G.; Wastie, R.; Terada, S.; Unno, Y.; Kohriki, T.; Ikegami, Y.; Hara, K.; Kobayashi, H.; Barbier, G.; Clark, A.G.; Perrin, E.; Carter, A.A.; Mistry, J.; Morris, J.

    2006-01-01

    The 2112 silicon detector modules of the barrel part of the ATLAS SemiConductor Tracker (SCT) have been mounted on their carbon fibre support structure. Module insertion, placement and fixing were performed by robotic assembly tooling. We report on our experience with this assembly method. Part of the mounting sequence involves a partial survey of elements of the support structure which is needed to align the modules properly during insertion. An analysis of these data is used to estimate the positional accuracy of the robots

  8. Forming Human-Robot Teams Across Time and Space

    Science.gov (United States)

    Hambuchen, Kimberly; Burridge, Robert R.; Ambrose, Robert O.; Bluethmann, William J.; Diftler, Myron A.; Radford, Nicolaus A.

    2012-01-01

    NASA pushes telerobotics to distances that span the Solar System. At this scale, time of flight for communication is limited by the speed of light, inducing long time delays, narrow bandwidth and the real risk of data disruption. NASA also supports missions where humans are in direct contact with robots during extravehicular activity (EVA), giving a range of zero to hundreds of millions of miles for NASA s definition of "tele". . Another temporal variable is mission phasing. NASA missions are now being considered that combine early robotic phases with later human arrival, then transition back to robot only operations. Robots can preposition, scout, sample or construct in advance of human teammates, transition to assistant roles when the crew are present, and then become care-takers when the crew returns to Earth. This paper will describe advances in robot safety and command interaction approaches developed to form effective human-robot teams, overcoming challenges of time delay and adapting as the team transitions from robot only to robots and crew. The work is predicated on the idea that when robots are alone in space, they are still part of a human-robot team acting as surrogates for people back on Earth or in other distant locations. Software, interaction modes and control methods will be described that can operate robots in all these conditions. A novel control mode for operating robots across time delay was developed using a graphical simulation on the human side of the communication, allowing a remote supervisor to drive and command a robot in simulation with no time delay, then monitor progress of the actual robot as data returns from the round trip to and from the robot. Since the robot must be responsible for safety out to at least the round trip time period, the authors developed a multi layer safety system able to detect and protect the robot and people in its workspace. This safety system is also running when humans are in direct contact with the robot

  9. Humanlike Robots - The Upcoming Revolution in Robotics

    Science.gov (United States)

    Bar-Cohen, Yoseph

    2009-01-01

    Humans have always sought to imitate the human appearance, functions and intelligence. Human-like robots, which for many years have been a science fiction, are increasingly becoming an engineering reality resulting from the many advances in biologically inspired technologies. These biomimetic technologies include artificial intelligence, artificial vision and hearing as well as artificial muscles, also known as electroactive polymers (EAP). Robots, such as the vacuum cleaner Rumba and the robotic lawnmower, that don't have human shape, are already finding growing use in homes worldwide. As opposed to other human-made machines and devices, this technology raises also various questions and concerns and they need to be addressed as the technology advances. These include the need to prevent accidents, deliberate harm, or their use in crime. In this paper the state-of-the-art of the ultimate goal of biomimetics, the development of humanlike robots, the potentials and the challenges are reviewed.

  10. Humanlike robots: the upcoming revolution in robotics

    Science.gov (United States)

    Bar-Cohen, Yoseph

    2009-08-01

    Humans have always sought to imitate the human appearance, functions and intelligence. Human-like robots, which for many years have been a science fiction, are increasingly becoming an engineering reality resulting from the many advances in biologically inspired technologies. These biomimetic technologies include artificial intelligence, artificial vision and hearing as well as artificial muscles, also known as electroactive polymers (EAP). Robots, such as the vacuum cleaner Rumba and the robotic lawnmower, that don't have human shape, are already finding growing use in homes worldwide. As opposed to other human-made machines and devices, this technology raises also various questions and concerns and they need to be addressed as the technology advances. These include the need to prevent accidents, deliberate harm, or their use in crime. In this paper the state-of-the-art of the ultimate goal of biomimetics, the development of humanlike robots, the potentials and the challenges are reviewed.

  11. Advances in Automation and Robotics

    CERN Document Server

    International conference on Automation and Robotics ICAR2011

    2012-01-01

    The international conference on Automation and Robotics-ICAR2011 is held during December 12-13, 2011 in Dubai, UAE. The proceedings of ICAR2011 have been published by Springer Lecture Notes in Electrical Engineering, which include 163 excellent papers selected from more than 400 submitted papers.   The conference is intended to bring together the researchers and engineers/technologists working in different aspects of intelligent control systems and optimization, robotics and automation, signal processing, sensors, systems modeling and control, industrial engineering, production and management.   This part of proceedings includes 81 papers contributed by many researchers in relevant topic areas covered at ICAR2011 from various countries such as France, Japan, USA, Korea and China etc.     Many papers introduced their advanced research work recently; some of them gave a new solution to problems in the field, with powerful evidence and detail demonstration. Others stated the application of their designed and...

  12. Environmental services in Zavidovici (Bosnia Herzegovina): current situation and proposals for intervention-Part 1.: Drinking water treatment and distribution

    International Nuclear Information System (INIS)

    Vaccari, M.; Collivignarelli, C.; Vitali, F.

    2009-01-01

    The state of the environment in Bosnia Herzegovina, already compromised before the war by the development of heavy industry, worsened after the conflict. The country is facing difficult issues in the supply of environmental services, which have recently been overlooked with regard to full coverage of the territory with adequate infrastructures and appropriate management of the existing ones. Several years ago CeTAmb started collaborating with the Local Democracy Agency in Zavidovici and local institutions: within that cooperation a survey of environmental services (water supply, wastewater collection and treatment, solid waste management) supplied to the municipal territory was implemented. The first part of the paper presents the different issues, and relative improvement solutions proposed, resulting from an analysis of the water supply infrastructures, with regard to both quantity and quality. [it

  13. How to decide which infant can have robotic surgery? Just do the math.

    Science.gov (United States)

    Finkelstein, J B; Levy, A C; Silva, M V; Murray, L; Delaney, C; Casale, P

    2015-08-01

    infant population is, in part, dependent on careful patient selection. Our data demonstrated a reduction in instrument collisions and console time with increasing anterior superior iliac spine and puboxyphoid distances. Neither age nor weight was correlated with these measurements, the number of instrument collisions or console time. Limitations include that this is a single institution study with all infants being operated on by a single surgeon. Therefore, the findings of this study may not be generalizable to a less experienced surgeon. Yet, we believe that ASIS and PXD measurements can be used as a guide for the novice surgeon who is beginning to perform robotic-assisted surgery in infants. We found that surgeon ability to perform robotic surgery in an infant is restricted by collisions when the infant has an ASIS measurement of 13 cm or less or a PXD of 15 cm or less. Objective assessment of anterior superior iliac spine and puboxyphoid distance can aid in selecting which infants can safely and efficiently undergo robotic intervention with a minimum of instrument collision, thereby minimizing operative time. Copyright © 2015 Journal of Pediatric Urology Company. Published by Elsevier Ltd. All rights reserved.

  14. Robotic devices for nuclear plant

    Energy Technology Data Exchange (ETDEWEB)

    Abel, E

    1986-05-01

    The article surveys the background of nuclear remote handling and its associated technology, robotics. Manipulators, robots, robot applications, extending the range of applications, and future developments, are all discussed.

  15. Evolutionary robotics – A review

    Indian Academy of Sciences (India)

    R. Narasimhan (Krishtel eMaging) 1461 1996 Oct 15 13:05:22

    a need for a technique by which the robot is able to acquire new behaviours automatically .... Evolutionary robotics is a comparatively new field of robotics research, which seems to ..... Technical Report: PCIA-94-04, Institute of Psychology,.

  16. Grasping in Robotics

    CERN Document Server

    2013-01-01

    Grasping in Robotics contains original contributions in the field of grasping in robotics with a broad multidisciplinary approach. This gives the possibility of addressing all the major issues related to robotized grasping, including milestones in grasping through the centuries, mechanical design issues, control issues, modelling achievements and issues, formulations and software for simulation purposes, sensors and vision integration, applications in industrial field and non-conventional applications (including service robotics and agriculture).   The contributors to this book are experts in their own diverse and wide ranging fields. This multidisciplinary approach can help make Grasping in Robotics of interest to a very wide audience. In particular, it can be a useful reference book for researchers, students and users in the wide field of grasping in robotics from many different disciplines including mechanical design, hardware design, control design, user interfaces, modelling, simulation, sensors and hum...

  17. Robot Games for Elderly

    DEFF Research Database (Denmark)

    Hansen, Søren Tranberg

    2011-01-01

    improve a person’s overall health, and this thesis investigates how games based on an autonomous, mobile robot platform, can be used to motivate elderly to move physically while playing. The focus of the investigation is on the development of games for an autonomous, mobile robot based on algorithms using...... spatio-temporal information about player behaviour - more specifically, I investigate three types of games each using a different control strategy. The first game is based on basic robot control which allows the robot to detect and follow a person. A field study in a rehabilitation centre and a nursing....... The robot facilitates interaction, and the study suggests that robot based games potentially can be used for training balance and orientation. The second game consists in an adaptive game algorithm which gradually adjusts the game challenge to the mobility skills of the player based on spatio...

  18. Survival of falling robots

    Science.gov (United States)

    Cameron, Jonathan M.; Arkin, Ronald C.

    1992-01-01

    As mobile robots are used in more uncertain and dangerous environments, it will become important to design them so that they can survive falls. In this paper, we examine a number of mechanisms and strategies that animals use to withstand these potentially catastrophic events and extend them to the design of robots. A brief survey of several aspects of how common cats survive falls provides an understanding of the issues involved in preventing traumatic injury during a falling event. After outlining situations in which robots might fall, a number of factors affecting their survival are described. From this background, several robot design guidelines are derived. These include recommendations for the physical structure of the robot as well as requirements for the robot control architecture. A control architecture is proposed based on reactive control techniques and action-oriented perception that is geared to support this form of survival behavior.

  19. Robotic surgery update.

    Science.gov (United States)

    Jacobsen, G; Elli, F; Horgan, S

    2004-08-01

    Minimally invasive surgical techniques have revolutionized the field of surgery. Telesurgical manipulators (robots) and new information technologies strive to improve upon currently available minimally invasive techniques and create new possibilities. A retrospective review of all robotic cases at a single academic medical center from August 2000 until November 2002 was conducted. A comprehensive literature evaluation on robotic surgical technology was also performed. Robotic technology is safely and effectively being applied at our institution. Robotic and information technologies have improved upon minimally invasive surgical techniques and created new opportunities not attainable in open surgery. Robotic technology offers many benefits over traditional minimal access techniques and has been proven safe and effective. Further research is needed to better define the optimal application of this technology. Credentialing and educational requirements also need to be delineated.

  20. Survival of falling robots

    Science.gov (United States)

    Cameron, Jonathan M.; Arkin, Ronald C.

    1992-02-01

    As mobile robots are used in more uncertain and dangerous environments, it will become important to design them so that they can survive falls. In this paper, we examine a number of mechanisms and strategies that animals use to withstand these potentially catastrophic events and extend them to the design of robots. A brief survey of several aspects of how common cats survive falls provides an understanding of the issues involved in preventing traumatic injury during a falling event. After outlining situations in which robots might fall, a number of factors affecting their survival are described. From this background, several robot design guidelines are derived. These include recommendations for the physical structure of the robot as well as requirements for the robot control architecture. A control architecture is proposed based on reactive control techniques and action-oriented perception that is geared to support this form of survival behavior.

  1. Nasa's Ant-Inspired Swarmie Robots

    Science.gov (United States)

    Leucht, Kurt W.

    2016-01-01

    As humans push further beyond the grasp of earth, robotic missions in advance of human missions will play an increasingly important role. These robotic systems will find and retrieve valuable resources as part of an in-situ resource utilization (ISRU) strategy. They will need to be highly autonomous while maintaining high task performance levels. NASA Kennedy Space Center has teamed up with the Biological Computation Lab at the University of New Mexico to create a swarm of small, low-cost, autonomous robots to be used as a ground-based research platform for ISRU missions. The behavior of the robot swarm mimics the central-place foraging strategy of ants to find and collect resources in a previously unmapped environment and return those resources to a central site. This talk will guide the audience through the Swarmie robot project from its conception by students in a New Mexico research lab to its robot trials in an outdoor parking lot at NASA. The software technologies and techniques used on the project will be discussed, as well as various challenges and solutions that were encountered by the development team along the way.

  2. Manifold learning in machine vision and robotics

    Science.gov (United States)

    Bernstein, Alexander

    2017-02-01

    Smart algorithms are used in Machine vision and Robotics to organize or extract high-level information from the available data. Nowadays, Machine learning is an essential and ubiquitous tool to automate extraction patterns or regularities from data (images in Machine vision; camera, laser, and sonar sensors data in Robotics) in order to solve various subject-oriented tasks such as understanding and classification of images content, navigation of mobile autonomous robot in uncertain environments, robot manipulation in medical robotics and computer-assisted surgery, and other. Usually such data have high dimensionality, however, due to various dependencies between their components and constraints caused by physical reasons, all "feasible and usable data" occupy only a very small part in high dimensional "observation space" with smaller intrinsic dimensionality. Generally accepted model of such data is manifold model in accordance with which the data lie on or near an unknown manifold (surface) of lower dimensionality embedded in an ambient high dimensional observation space; real-world high-dimensional data obtained from "natural" sources meet, as a rule, this model. The use of Manifold learning technique in Machine vision and Robotics, which discovers a low-dimensional structure of high dimensional data and results in effective algorithms for solving of a large number of various subject-oriented tasks, is the content of the conference plenary speech some topics of which are in the paper.

  3. Fundamentals of soft robot locomotion

    OpenAIRE

    Calisti, M.; Picardi, G.; Laschi, C.

    2017-01-01

    Soft robotics and its related technologies enable robot abilities in several robotics domains including, but not exclusively related to, manipulation, manufacturing, human���robot interaction and locomotion. Although field applications have emerged for soft manipulation and human���robot interaction, mobile soft robots appear to remain in the research stage, involving the somehow conflictual goals of having a deformable body and exerting forces on the environment to achieve locomotion. This p...

  4. Robotic liver surgery

    Science.gov (United States)

    Leung, Universe

    2014-01-01

    Robotic surgery is an evolving technology that has been successfully applied to a number of surgical specialties, but its use in liver surgery has so far been limited. In this review article we discuss the challenges of minimally invasive liver surgery, the pros and cons of robotics, the evolution of medical robots, and the potentials in applying this technology to liver surgery. The current data in the literature are also presented. PMID:25392840

  5. Robotized transcranial magnetic stimulation

    CERN Document Server

    Richter, Lars

    2014-01-01

    Presents new, cutting-edge algorithms for robot/camera calibration, sensor fusion and sensor calibration Explores the main challenges for accurate coil positioning, such as head motion, and outlines how active robotic motion compensation can outperform hand-held solutions Analyzes how a robotized system in medicine can alleviate concerns with a patient's safety, and presents a novel fault-tolerant algorithm (FTA) sensor for system safety

  6. Raspberry Pi robotics projects

    CERN Document Server

    Grimmett, Richard

    2015-01-01

    This book is for enthusiasts who want to use the Raspberry Pi to build complex robotics projects. With the aid of the step-by-step instructions in this book, you can construct complex robotics projects that can move, talk, listen, see, swim, or fly. No previous Raspberry Pi robotics experience is assumed, but even experts will find unexpected and interesting information in this invaluable guide.

  7. Robots as Confederates

    DEFF Research Database (Denmark)

    Fischer, Kerstin

    2016-01-01

    This paper addresses the use of robots in experimental research for the study of human language, human interaction, and human nature. It is argued that robots make excellent confederates that can be completely controlled, yet which engage human participants in interactions that allow us to study...... numerous linguistic and psychological variables in isolation in an ecologically valid way. Robots thus combine the advantages of observational studies and of controlled experimentation....

  8. Robotics in General Surgery

    OpenAIRE

    Wall, James; Chandra, Venita; Krummel, Thomas

    2008-01-01

    In summary, robotics has made a significant contribution to General Surgery in the past 20 years. In its infancy, surgical robotics has seen a shift from early systems that assisted the surgeon to current teleoperator systems that can enhance surgical skills. Telepresence and augmented reality surgery are being realized, while research and development into miniaturization and automation is rapidly moving forward. The future of surgical robotics is bright. Researchers are working to address th...

  9. Robotic hand project

    OpenAIRE

    Karaçizmeli, Cengiz; Çakır, Gökçe; Tükel, Dilek

    2014-01-01

    In this work, the mechatronic based robotic hand is controlled by the position data taken from the glove which has flex sensors mounted to capture finger bending of the human hand. The angular movement of human hand’s fingers are perceived and processed by a microcontroller, and the robotic hand is controlled by actuating servo motors. It has seen that robotic hand can simulate the movement of the human hand that put on the glove, during tests have done. This robotic hand can be used not only...

  10. Perspectives of construction robots

    Science.gov (United States)

    Stepanov, M. A.; Gridchin, A. M.

    2018-03-01

    This article is an overview of construction robots features, based on formulating the list of requirements for different types of construction robots in relation to different types of construction works.. It describes a variety of construction works and ways to construct new or to adapt existing robot designs for a construction process. Also, it shows the prospects of AI-controlled machines, implementation of automated control systems and networks on construction sites. In the end, different ways to develop and improve, including ecological aspect, the construction process through the wide robotization, creating of data communication networks and, in perspective, establishing of fully AI-controlled construction complex are formulated.

  11. Robots de servicio

    OpenAIRE

    Aracil, Rafael; Balaguer, Carlos; Armada, Manuel

    2008-01-01

    8 págs, 9 figs. El término Robots de Servicio apareció a finales de los años 80 como una necesidad de desarrollar máquinas y sistemas capaces de trabajar en entornos diferentes a los fabriles. Los Robots de Servicio tenían que poder trabajar en entornos noestructurados, en condiciones ambientales cambiantes y con una estrecha interacción con los humanos. En 1995 fue creado por la IEEE Robotics and Automation Society, el Technical Committee on Service Robots, y este comité definió en el año...

  12. Human-Robot Interaction

    Science.gov (United States)

    Sandor, Aniko; Cross, E. Vincent, II; Chang, Mai Lee

    2015-01-01

    Human-robot interaction (HRI) is a discipline investigating the factors affecting the interactions between humans and robots. It is important to evaluate how the design of interfaces affect the human's ability to perform tasks effectively and efficiently when working with a robot. By understanding the effects of interface design on human performance, workload, and situation awareness, interfaces can be developed to appropriately support the human in performing tasks with minimal errors and with appropriate interaction time and effort. Thus, the results of research on human-robot interfaces have direct implications for the design of robotic systems. For efficient and effective remote navigation of a rover, a human operator needs to be aware of the robot's environment. However, during teleoperation, operators may get information about the environment only through a robot's front-mounted camera causing a keyhole effect. The keyhole effect reduces situation awareness which may manifest in navigation issues such as higher number of collisions, missing critical aspects of the environment, or reduced speed. One way to compensate for the keyhole effect and the ambiguities operators experience when they teleoperate a robot is adding multiple cameras and including the robot chassis in the camera view. Augmented reality, such as overlays, can also enhance the way a person sees objects in the environment or in camera views by making them more visible. Scenes can be augmented with integrated telemetry, procedures, or map information. Furthermore, the addition of an exocentric (i.e., third-person) field of view from a camera placed in the robot's environment may provide operators with the additional information needed to gain spatial awareness of the robot. Two research studies investigated possible mitigation approaches to address the keyhole effect: 1) combining the inclusion of the robot chassis in the camera view with augmented reality overlays, and 2) modifying the camera

  13. Advanced robot locomotion.

    Energy Technology Data Exchange (ETDEWEB)

    Neely, Jason C.; Sturgis, Beverly Rainwater; Byrne, Raymond Harry; Feddema, John Todd; Spletzer, Barry Louis; Rose, Scott E.; Novick, David Keith; Wilson, David Gerald; Buerger, Stephen P.

    2007-01-01

    This report contains the results of a research effort on advanced robot locomotion. The majority of this work focuses on walking robots. Walking robot applications include delivery of special payloads to unique locations that require human locomotion to exo-skeleton human assistance applications. A walking robot could step over obstacles and move through narrow openings that a wheeled or tracked vehicle could not overcome. It could pick up and manipulate objects in ways that a standard robot gripper could not. Most importantly, a walking robot would be able to rapidly perform these tasks through an intuitive user interface that mimics natural human motion. The largest obstacle arises in emulating stability and balance control naturally present in humans but needed for bipedal locomotion in a robot. A tracked robot is bulky and limited, but a wide wheel base assures passive stability. Human bipedal motion is so common that it is taken for granted, but bipedal motion requires active balance and stability control for which the analysis is non-trivial. This report contains an extensive literature study on the state-of-the-art of legged robotics, and it additionally provides the analysis, simulation, and hardware verification of two variants of a proto-type leg design.

  14. Robotic assisted laparoscopic colectomy.

    LENUS (Irish Health Repository)

    Pandalai, S

    2010-06-01

    Robotic surgery has evolved over the last decade to compensate for limitations in human dexterity. It avoids the need for a trained assistant while decreasing error rates such as perforations. The nature of the robotic assistance varies from voice activated camera control to more elaborate telerobotic systems such as the Zeus and the Da Vinci where the surgeon controls the robotic arms using a console. Herein, we report the first series of robotic assisted colectomies in Ireland using a voice activated camera control system.

  15. Autonomous military robotics

    CERN Document Server

    Nath, Vishnu

    2014-01-01

    This SpringerBrief reveals the latest techniques in computer vision and machine learning on robots that are designed as accurate and efficient military snipers. Militaries around the world are investigating this technology to simplify the time, cost and safety measures necessary for training human snipers. These robots are developed by combining crucial aspects of computer science research areas including image processing, robotic kinematics and learning algorithms. The authors explain how a new humanoid robot, the iCub, uses high-speed cameras and computer vision algorithms to track the objec

  16. Soft-Material Robotics

    OpenAIRE

    Wang, L; Nurzaman, SG; Iida, Fumiya

    2017-01-01

    There has been a boost of research activities in robotics using soft materials in the past ten years. It is expected that the use and control of soft materials can help realize robotic systems that are safer, cheaper, and more adaptable than the level that the conventional rigid-material robots can achieve. Contrary to a number of existing review and position papers on soft-material robotics, which mostly present case studies and/or discuss trends and challenges, the review focuses on the fun...

  17. Robotics for nuclear facilities

    International Nuclear Information System (INIS)

    Abe, Akira; Nakayama, Ryoichi; Kubo, Katsumi

    1988-01-01

    It is highly desirable that automatic or remotely controlled machines perform inspection and maintenance tasks in nuclear facilities. Toshiba has been working to develop multi-functional robots, with one typical example being a master-slave manipulator for use in reprocessing facilities. At the same time, the company is also working on the development of multi-purpose intelligent robots. One such device, an automatic inspection robot, to be deployed along a monorail, performs inspection by means of image processing technology, while and advanced intelligent maintenance robot is equipped with a special wheel-locomotion mechanism and manipulator and is designed to perform maintenance tasks. (author)

  18. Increasing Robotic Science Applications

    Data.gov (United States)

    National Aeronautics and Space Administration — The principal objectives are to demonstrate robotic-based scientific investigations and resource prospecting, and develop and demonstrate modular science instrument...

  19. DSLs in robotics

    DEFF Research Database (Denmark)

    Schultz, Ulrik Pagh; Bordignon, Mirko; Stoy, Kasper

    2017-01-01

    Robotic systems blend hardware and software in a holistic way that intrinsically raises many crosscutting concerns such as concurrency, uncertainty, and time constraints. These concerns make programming robotic systems challenging as expertise from multiple domains needs to be integrated...... conceptually and technically. Programming languages play a central role in providing a higher level of abstraction. This briefing presents a case study on the evolution of domain-specific languages based on modular robotics. The case study on the evolution of domain-specific languages is based on a series...... of DSL prototypes developed over five years for the domain of modular, self-reconfigurable robots....

  20. Advances in soft computing, intelligent robotics and control

    CERN Document Server

    Fullér, Robert

    2014-01-01

    Soft computing, intelligent robotics and control are in the core interest of contemporary engineering. Essential characteristics of soft computing methods are the ability to handle vague information, to apply human-like reasoning, their learning capability, and ease of application. Soft computing techniques are widely applied in the control of dynamic systems, including mobile robots. The present volume is a collection of 20 chapters written by respectable experts of the fields, addressing various theoretical and practical aspects in soft computing, intelligent robotics and control. The first part of the book concerns with issues of intelligent robotics, including robust xed point transformation design, experimental verification of the input-output feedback linearization of differentially driven mobile robot and applying kinematic synthesis to micro electro-mechanical systems design. The second part of the book is devoted to fundamental aspects of soft computing. This includes practical aspects of fuzzy rule ...

  1. A Research Synthesis of Therapeutic Interventions for Whiplash-Associated Disorder: Part 1 – Overview and Summary

    Directory of Open Access Journals (Sweden)

    Robert W Teasell

    2010-01-01

    Full Text Available Whiplash-associated disorder (WAD represents a significant public health problem, resulting in a substantial socioeconomic burden throughout the industrialized world, wherever costs are documented. While many treatments have been advocated for patients with WAD, scientific evidence of their effectiveness is often lacking. A systematic review was conducted to evaluate the strength of evidence supporting various WAD therapies. Multiple databases (including Web of Science, EMBASE and PubMed were searched to identify all studies published from January 1980 through March 2009 that evaluated the effectiveness of any clearly defined treatment for acute (less than two weeks, subacute (two to 12 weeks or chronic (longer than 12 weeks WAD. The present article, the first in a five-part series, provides an overview of the review methodology as well as a summary and discussion of the review’s main findings. Eighty-three studies met the inclusion criteria, 40 of which were randomized controlled trials. The majority of studies (n=47 evaluated treatments initiated in the chronic stage of the disorder, while 23 evaluated treatments for acute WAD and 13 assessed therapies for subacute WAD. Exercise and mobilization programs for acute and chronic WAD had the strongest supporting evidence, although many questions remain regarding the relative effectiveness of various protocols. At present, there is insufficient evidence to support any treatment for subacute WAD. For patients with chronic WAD who do not respond to conventional treatments, it appears that radiofrequency neurotomy may be the most effective treatment option. The present review found a relatively weak but growing research base on which one could make recommendations for patients at any stage of the WAD continuum. Further research is needed to determine which treatments are most effective at reducing the disabling symptoms associated with WAD.

  2. Medical Robotics - A Real Challenge of Present and Especially Future

    Directory of Open Access Journals (Sweden)

    Ionel STARETU

    2013-12-01

    Full Text Available If we make a brief scan of the field known as Medical Robotics, we find that in recent years there has been an impetuous development of applications involving medical robots. Obviously, the most spectacular are remote robotic surgery systems, which, for example, in U.S. have been used in more than 3.5-4 million interventions. The systems AESOP, da Vinci and ZEUS are currently run in minimally invasive robotic surgery. Encouraging results were obtained at MIT (USA using robots in physiotherapy. Pearl is a robot designed as personal assistant of older patients, affected by disabilities. The Universities of Pittsburgh and Carnegie Mellon successfully develop it. In Plymouth and Aachen, researchers are involved in the creation of intelligent wheelchairs. At the University of Karlsruhe, robotic systems applicable to neurosurgery are created. Thus, the MICRoN project aims to create a robot to manipulate micron-sized objects with nanometer precision, applications including intervention in the living biological cells. In several research centers one works on the improvement of neural interfaces, from which it is expected a new generation of prostheses, controlled through functional electrical stimulation. It is also projected that the microsystem technology (MST will have a major impact in medicine through the introduction of new diagnostic techniques, dosing, remote microsurgery and neural prostheses, all based on the concept of minimally invasive therapy, mentioned above. This is the approximate image of research in Medical Robotics and obviously of some related fields, whose dynamics has been impressive lately, a trend that is maintained and even has clear signs of amplification, and fully justifies this approach. In this context, we will present the main concepts and applications of medical robotics in order to achieve a more suggestive and convincing image of this area of great interest and perspective.

  3. Development of Methodologies, Metrics, and Tools for Investigating Human-Robot Interaction in Space Robotics

    Science.gov (United States)

    Ezer, Neta; Zumbado, Jennifer Rochlis; Sandor, Aniko; Boyer, Jennifer

    2011-01-01

    Human-robot systems are expected to have a central role in future space exploration missions that extend beyond low-earth orbit [1]. As part of a directed research project funded by NASA s Human Research Program (HRP), researchers at the Johnson Space Center have started to use a variety of techniques, including literature reviews, case studies, knowledge capture, field studies, and experiments to understand critical human-robot interaction (HRI) variables for current and future systems. Activities accomplished to date include observations of the International Space Station s Special Purpose Dexterous Manipulator (SPDM), Robonaut, and Space Exploration Vehicle (SEV), as well as interviews with robotics trainers, robot operators, and developers of gesture interfaces. A survey of methods and metrics used in HRI was completed to identify those most applicable to space robotics. These methods and metrics included techniques and tools associated with task performance, the quantification of human-robot interactions and communication, usability, human workload, and situation awareness. The need for more research in areas such as natural interfaces, compensations for loss of signal and poor video quality, psycho-physiological feedback, and common HRI testbeds were identified. The initial findings from these activities and planned future research are discussed. Human-robot systems are expected to have a central role in future space exploration missions that extend beyond low-earth orbit [1]. As part of a directed research project funded by NASA s Human Research Program (HRP), researchers at the Johnson Space Center have started to use a variety of techniques, including literature reviews, case studies, knowledge capture, field studies, and experiments to understand critical human-robot interaction (HRI) variables for current and future systems. Activities accomplished to date include observations of the International Space Station s Special Purpose Dexterous Manipulator

  4. Strategy for robot motion and path planning in robot taping

    Science.gov (United States)

    Yuan, Qilong; Chen, I.-Ming; Lembono, Teguh Santoso; Landén, Simon Nelson; Malmgren, Victor

    2016-06-01

    Covering objects with masking tapes is a common process for surface protection in processes like spray painting, plasma spraying, shot peening, etc. Manual taping is tedious and takes a lot of effort of the workers. The taping process is a special process which requires correct surface covering strategy and proper attachment of the masking tape for an efficient surface protection. We have introduced an automatic robot taping system consisting of a robot manipulator, a rotating platform, a 3D scanner and specially designed taping end-effectors. This paper mainly talks about the surface covering strategies for different classes of geometries. The methods and corresponding taping tools are introduced for taping of following classes of surfaces: Cylindrical/extended surfaces, freeform surfaces with no grooves, surfaces with grooves, and rotational symmetrical surfaces. A collision avoidance algorithm is introduced for the robot taping manipulation. With further improvements on segmenting surfaces of taping parts and tape cutting mechanisms, such taping solution with the taping tool and the taping methodology can be combined as a very useful and practical taping package to assist humans in this tedious and time costly work.

  5. Organizational System for the LEGO WeDo 2.0 Robotics System

    Science.gov (United States)

    Dolecheck, Suzann Hagan; Ewers, Timothy

    2017-01-01

    In this article, we explain an organizational system for the new LEGO Education WeDo 2.0 Core Set used in 4-H robotics; in school enrichment, afterschool, and other youth robotics programs; and by hobbyists. The system presented is for organizing WeDo parts into a translucent parts tray that includes part names and numbers. The article provides…

  6. Soft Robotics: from scientific challenges to technological applications

    Science.gov (United States)

    Laschi, C.

    2016-05-01

    Soft robotics is a recent and rapidly growing field of research, which aims at unveiling the principles for building robots that include soft materials and compliance in the interaction with the environment, so as to exploit so-called embodied intelligence and negotiate natural environment more effectively. Using soft materials for building robots poses new technological challenges: the technologies for actuating soft materials, for embedding sensors into soft robot parts, for controlling soft robots are among the main ones. This is stimulating research in many disciplines and many countries, such that a wide community is gathering around initiatives like the IEEE TAS TC on Soft Robotics and the RoboSoft CA - A Coordination Action for Soft Robotics, funded by the European Commission. Though still in its early stages of development, soft robotics is finding its way in a variety of applications, where safe contact is a main issue, in the biomedical field, as well as in exploration tasks and in the manufacturing industry. And though the development of the enabling technologies is still a priority, a fruitful loop is growing between basic research and application-oriented research in soft robotics.

  7. Approaching human performance the functionality-driven Awiwi robot hand

    CERN Document Server

    Grebenstein, Markus

    2014-01-01

    Humanoid robotics have made remarkable progress since the dawn of robotics. So why don't we have humanoid robot assistants in day-to-day life yet? This book analyzes the keys to building a successful humanoid robot for field robotics, where collisions become an unavoidable part of the game. The author argues that the design goal should be real anthropomorphism, as opposed to mere human-like appearance. He deduces three major characteristics to aim for when designing a humanoid robot, particularly robot hands: _ Robustness against impacts _ Fast dynamics _ Human-like grasping and manipulation performance   Instead of blindly copying human anatomy, this book opts for a holistic design me-tho-do-lo-gy. It analyzes human hands and existing robot hands to elucidate the important functionalities that are the building blocks toward these necessary characteristics.They are the keys to designing an anthropomorphic robot hand, as illustrated in the high performance anthropomorphic Awiwi Hand presented in this book.  ...

  8. Robot technology

    International Nuclear Information System (INIS)

    Vertut, Jean; Coiffet, Philippe.

    1985-01-01

    Teleoperation is concerned with the exploration and exploitation of spaces which do not allow, because of their inaccessibility or hostility, direct access to man. This volume (Part 1) covers the advances in mastering teleoperation, using only a knowledge of mechanics. The story is one of a gradual orderly succession of creative designs over many years. Diagrams and photographs illustrate the designs. This a comprehensive coverage of the subject. Following a chapter on the background to the subject the chapters cover the classification of teleoperation systems, mechanical master-slave telemanipulators for handling radioactive materials, motorized unilateral telemanipulators with open-loop control, bilateral servo manipulators, transporters and vehicles and, finally, one on the art of teleoperation at the time of the introduction of computer science. The book has been translated from French. (U.K.)

  9. Multi-robot control interface

    Science.gov (United States)

    Bruemmer, David J [Idaho Falls, ID; Walton, Miles C [Idaho Falls, ID

    2011-12-06

    Methods and systems for controlling a plurality of robots through a single user interface include at least one robot display window for each of the plurality of robots with the at least one robot display window illustrating one or more conditions of a respective one of the plurality of robots. The user interface further includes at least one robot control window for each of the plurality of robots with the at least one robot control window configured to receive one or more commands for sending to the respective one of the plurality of robots. The user interface further includes a multi-robot common window comprised of information received from each of the plurality of robots.

  10. Robotics and nuclear power. Report by the Technology Transfer Robotics Task Team

    International Nuclear Information System (INIS)

    1985-06-01

    A task team was formed at the request of the Department of Energy to evaluate and assess technology development needed for advanced robotics in the nuclear industry. The mission of these technologies is to provide the nuclear industry with the support for the application of advanced robotics to reduce nuclear power generating costs and enhance the safety of the personnel in the industry. The investigation included robotic and teleoperated systems. A robotic system is defined as a reprogrammable, multifunctional manipulator designed to move materials, parts, tools, or specialized devices through variable programmed motions for the performance of a variety of tasks. A teleoperated system includes an operator who remotely controls the system by direct viewing or through a vision system

  11. Rehabilitation Robots: Concepts and Applications in Stroke Rehabilitation

    Directory of Open Access Journals (Sweden)

    Mohammad Ali Ahmadi-Pajouh

    2017-02-01

    Full Text Available Robotics is a tool to assist human in different applications from industry to medicine. There are many reasons that human tends to use these machines. They are very reliable in repetitive, high precision, preprogrammed and high risk jobs in which human is not too good enough. In medicine, robotic applications are evolving so fast that in near future nobody can imagine a surgery without a robot involved. In Rehabilitation we have the same scenario; there are commercialized robots to assist disable people to eat and perform daily activities. There are also clinical rehabilitation robots which can train handicaps. They can help subjects as a passive tool that improves low level impairments such as rigidity. On the other hand robots can train brain as an active tool to have a better movement again. We will see how robots can help therapist to apply repetitive passive movements in quadriplegic subject (i.e. in Brunnstrom stages 1 to 3. On the other hand they can teach subjects how to complete a task in an active manner (i.e. in stages 5 and 6 which can facilitate neuroplasticity. There are different robots designed for different organs; for example rehabilitation of upper extremities (e.g. Gloreha or lower extremities (e.g. Lokomat. There are also exoskeleton robots to help subjects to grip objects and perform ADLs easily (e.g. Bioservo or help paraplegic patient to walk again (e.g. Rewalk. In this talk, we will also discuss about how robots are helping rehab specialist to improve standard protocols. For example we will show how action observation therapy, bimanual therapy, assistive active therapy, proprioceptive facilitation and passive mobilization therapy are realized using an upper extremity rehabilitation robot. Robotics is the future of technology and rehabilitation needs this technology. Be part of this technology!

  12. Vocal Production of Young Children with Disabilities during Child-Robot Interactions. Social Robots Research Reports, Number 5

    Science.gov (United States)

    Dunst, Carl J.; Hamby, Deborah W.; Trivette, Carol M.; Prior, Jeremy; Derryberry, Graham

    2013-01-01

    The effects of a socially interactive robot on the vocalization production of five children with disabilities (4 with autism, 1 with a sensory processing disorder) were the focus of the intervention study described in this research report. The interventions with each child were conducted over 4 or 5 days in the children's homes and involved…

  13. Essential technologies for developing human and robot collaborative system

    International Nuclear Information System (INIS)

    Ishikawa, Nobuyuki; Suzuki, Katsuo

    1997-10-01

    In this study, we aim to develop a concept of new robot system, i.e., 'human and robot collaborative system', for the patrol of nuclear power plants. This paper deals with the two essential technologies developed for the system. One is the autonomous navigation program with human intervention function which is indispensable for human and robot collaboration. The other is the position estimation method by using gyroscope and TV image to make the estimation accuracy much higher for safe navigation. Feasibility of the position estimation method is evaluated by experiment and numerical simulation. (author)

  14. Automating the Incremental Evolution of Controllers for Physical Robots

    DEFF Research Database (Denmark)

    Faina, Andres; Jacobsen, Lars Toft; Risi, Sebastian

    2017-01-01

    the evolution of digital objects.…” The work presented here investigates how fully autonomous evolution of robot controllers can be realized in hardware, using an industrial robot and a marker-based computer vision system. In particular, this article presents an approach to automate the reconfiguration...... of the test environment and shows that it is possible, for the first time, to incrementally evolve a neural robot controller for different obstacle avoidance tasks with no human intervention. Importantly, the system offers a high level of robustness and precision that could potentially open up the range...

  15. Design and Implementation an Autonomous Humanoid Robot Based on Fuzzy Rule-Based Motion Controller

    Directory of Open Access Journals (Sweden)

    Mohsen Taheri

    2010-04-01

    Full Text Available Research on humanoid robotics in Mechatronics and Automation Laboratory, Electrical and Computer Engineering, Islamic Azad University Khorasgan branch (Isfahan of Iran was started at
    the beginning of this decade. Various research prototypes for humanoid robots have been designed and are going through evolution over these years. This paper describes the hardware and software design of the kid size humanoid robot systems of the PERSIA Team in 2009. The robot has 20 actuated degrees of freedom based on Hitec HSR898. In this paper we have tried to focus on areas such as mechanical structure, Image processing unit, robot controller, Robot AI and behavior
    learning. In 2009, our developments for the Kid size humanoid robot include: (1 the design and construction of our new humanoid robots (2 the design and construction of a new hardware and software controller to be used in our robots. The project is described in two main parts: Hardware and Software. The software is developed a robot application which consists walking controller, autonomous motion robot, self localization base on vision and Particle Filter, local AI, Trajectory Planning, Motion Controller and Network. The hardware consists of the mechanical structure and the driver circuit board. Each robot is able to walk, fast walk, pass, kick and dribble when it catches
    the ball. These humanoids have been successfully participating in various robotic soccer competitions. This project is still in progress and some new interesting methods are described in the current report.

  16. Developing a Motion Comic for HIV/STD Prevention for Young People Ages 15-24, Part 2: Evaluation of a Pilot Intervention.

    Science.gov (United States)

    Willis, Leigh A; Kachur, Rachel; Castellanos, Ted J; Nichols, Kristen; Mendoza, Maria C B; Gaul, Zaneta J; Spikes, Pilgrim; Gamayo, Ashley C; Durham, Marcus D; LaPlace, Lisa; Straw, Julie; Staatz, Colleen; Buge, Hadiza; Hogben, Matthew; Robinson, Susan; Brooks, John; Sutton, Madeline Y

    2018-03-01

    In the United States, young people (ages 15-24 years) are disproportionately affected by human immunodeficiency virus (HIV) and other sexually transmitted diseases (STDs), due at least in part to inadequate or incorrect HIV/STD-related knowledge, attitudes, beliefs, and behavioral intentions (KABI). Comic book narratives are a proven method of HIV/STD prevention communication to strengthen KABI for HIV/STD prevention. Motion comics, a new type of comic media, are an engaging and low-cost means of narrative storytelling. The objective of this study was to quantitatively evaluate the effectiveness of a pilot six-episode HIV/STD-focused motion comic series to improve HIV/STD-related KABI among young people. We assessed change in HIV/STD knowledge, HIV stigma, condom attitudes, HIV/STD testing attitudes, and behavioral intentions among 138 participants in 15 focus groups immediately before and after viewing the motion comic series. We used paired t-tests and indicators of overall improvement to assess differences between surveys. We found a significant decrease in HIV stigma (p comic intervention improved HIV/STD-related KABI of young adult viewers by reducing HIV stigma and increasing behavioral intentions to engage in safer sex. Our results demonstrate the promise of this novel intervention and support its use to deliver health messages to young people.

  17. Tool-change coupling for robots

    International Nuclear Information System (INIS)

    Cooper, C.

    1988-01-01

    A coupling device for use in enabling a robotic unit to couple automatically with any one of a number of tools, comprises two coupling parts connected respectively to the tool and the arm. The two parts can be brought into interengaged relationship by appropriate manipulation of the arm and can be locked together by means of a locking element, controlled by piston and cylinder assembly which enters a tapered bore in a spigot after the spigot, which is mounted on the coupling part, has entered a bore in the other coupling part. The parts also incorporate registering passages for providing continuity of pressurised air supply between the robotic unit and a fluid-powered device incorporated in the tool. (author)

  18. Robots: l'embarras de richesses [:survey of robots available

    International Nuclear Information System (INIS)

    Meieran, H.; Brittain, K.; Sturkey, R.

    1989-01-01

    A survey of robots available for use in the nuclear industry is presented. Two new categories of mobile robots have been introduced since the last survey (April 1987): pipe crawlers and underwater robots. The number of robots available has risen to double what it was two years ago and four times what it was in 1986. (U.K.)

  19. Biomass feeds vegetarian robot; Biomassa voedt vegetarische robot

    Energy Technology Data Exchange (ETDEWEB)

    Van den Brandt, M. [Office for Science and Technology, Embassy of the Kingdom of the Netherlands, Washington (United States)

    2009-09-15

    This brief article addresses the EATR robot (Energetically Autonomous Tactical Robot) that was developed by Cyclone Power and uses biomass as primary source of energy for propulsion. [Dutch] Een kort artikel over de door Cyclone Power ontwikkelde EATR-robot (Energetically Autonomous Tactical Robot) die voor de voortdrijving biomassa gebruikt als primaire energiebron.

  20. Healthy Start - Départ Santé: A pilot study of a multilevel intervention to increase physical activity, fundamental movement skills and healthy eating in rural childcare centres.

    Science.gov (United States)

    Froehlich Chow, Amanda; Leis, Anne; Humbert, Louise; Muhajarine, Nazeem; Engler-Stringer, Rachel

    2016-10-20

    In order to improve healthy behaviours among rural children in their early years, a physical activity and healthy eating intervention (Healthy Start - Départ Santé) was implemented in rural childcare centres throughout Saskatchewan. The objective of the current study was to evaluate the impact of a multimodal physical activity and healthy eating intervention on educators' provision of opportunities for children to improve their physical activity levels, fundamental movement skills and healthy eating behaviours. Six childcare centres (three Francophone and three Anglophone) located in five different rural and semi-rural communities in Saskatchewan participated in this intervention. A total of 69 children with a mean age of 4 years 9 months, and 19 female early childhood educators. Guided by an ecological framework, we implemented a population health controlled intervention, using a wait list control design (48 weeks delayed intervention), and evaluated its impact in rural childcare centres. Mixed methods were employed to determine the effectiveness of the intervention. Overall, educators felt that the intervention supported the provision of physical activity and healthy eating opportunities for children. Increases in children's physical activity levels were reported following the intervention. The lessons learned in this study can be used to improve the Healthy Start - Départ Santé intervention so that its implementation can be effectively expanded to childcare centres within and outside Saskatchewan, in turn, supporting the healthy development of early years (0-5) children in the province and beyond.

  1. NOSC/ONR Robotics Bibliography (1961-1981).

    Science.gov (United States)

    1982-09-01

    28, 6 Dec., 1979 @, p4 "DEFENSE EQUIPMENT FIRM TRAINS ROBOT TO PERFORM CRAFTSMAN-SKILLED TASK", Industrial Engineering, vol 13, no 5, May 1981 @, p90...1974 @, pCI-I-8 Gupton, J. A. Jr., "BUILD THIS UNICORN -i ROBOT PART I", Radio-Electronics, vol 51, no 8, 1980 @, p 3 7 ,4 1 ,76 Gupton, J. A. Jr...34BUILD THIS UNICORN -i ROBOT PART II", Radio-Electronics, vol 51, no 9, Sept. 1980 @, p55-8 Gupton, J. A., Jr., "TALK TO A TURTLE; BUILD A COMPUTER

  2. Effective programming of energy consuming industrial robot systems

    International Nuclear Information System (INIS)

    Trnka, K.; Pinter, T.; Knazik, M.; Bozek, P.

    2012-01-01

    This paper discusses the problem of effective motion planning for industrial robots. The first part dealt with current method for off-line motion planning. In the second part is presented the work done with one of the simulation system with automatic trajectory generation and off-line programming capability [4]. An spot welding process is involved. The practical application of this step strongly depends on the method for robot path optimization with high accuracy, thus, transform the path into a time and energy optimal robot program for the real world, which is discussed in the third step. (Authors)

  3. Can we trust robots?

    NARCIS (Netherlands)

    Coeckelbergh, Mark

    2011-01-01

    Can we trust robots? Responding to the literature on trust and e-trust, this paper asks if the question of trust is applicable to robots, discusses different approaches to trust, and analyses some preconditions for trust. In the course of the paper a phenomenological-social approach to trust is

  4. Robotics in endoscopy.

    Science.gov (United States)

    Klibansky, David; Rothstein, Richard I

    2012-09-01

    The increasing complexity of intralumenal and emerging translumenal endoscopic procedures has created an opportunity to apply robotics in endoscopy. Computer-assisted or direct-drive robotic technology allows the triangulation of flexible tools through telemanipulation. The creation of new flexible operative platforms, along with other emerging technology such as nanobots and steerable capsules, can be transformational for endoscopic procedures. In this review, we cover some background information on the use of robotics in surgery and endoscopy, and review the emerging literature on platforms, capsules, and mini-robotic units. The development of techniques in advanced intralumenal endoscopy (endoscopic mucosal resection and endoscopic submucosal dissection) and translumenal endoscopic procedures (NOTES) has generated a number of novel platforms, flexible tools, and devices that can apply robotic principles to endoscopy. The development of a fully flexible endoscopic surgical toolkit will enable increasingly advanced procedures to be performed through natural orifices. The application of platforms and new flexible tools to the areas of advanced endoscopy and NOTES heralds the opportunity to employ useful robotic technology. Following the examples of the utility of robotics from the field of laparoscopic surgery, we can anticipate the emerging role of robotic technology in endoscopy.

  5. Neuronal nets in robotics

    International Nuclear Information System (INIS)

    Jimenez Sanchez, Raul

    1999-01-01

    The paper gives a generic idea of the solutions that the neuronal nets contribute to the robotics. The advantages and the inconveniences are exposed that have regarding the conventional techniques. It also describe the more excellent applications as the pursuit of trajectories, the positioning based on images, the force control or of the mobile robots management, among others

  6. Modelling of Hydraulic Robot

    DEFF Research Database (Denmark)

    Madsen, Henrik; Zhou, Jianjun; Hansen, Lars Henrik

    1997-01-01

    This paper describes a case study of identifying the physical model (or the grey box model) of a hydraulic test robot. The obtained model is intended to provide a basis for model-based control of the robot. The physical model is formulated in continuous time and is derived by application...

  7. Robots that care

    NARCIS (Netherlands)

    Looije, R.; Arendsen, J.; Saldien, J.; Vanderborght, B.; Broekens, J.; Neerincx, M.

    2010-01-01

    Many countries face pressure on their health care systems. To alleviate this pressure, 'self care' and 'self monitoring' are often stimulated with the use of new assistive technologies. Social robotics is a research area where robotic technology is optimized for various social functions. One of

  8. Robotics and Industrial Arts.

    Science.gov (United States)

    Edmison, Glenn A.; And Others

    Robots are becoming increasingly common in American industry. By l990, they will revolutionize the way industry functions, replacing hundreds of workers and doing hot, dirty jobs better and more quickly than the workers could have done them. Robotics should be taught in high school industrial arts programs as a major curriculum component. The…

  9. Robotics in medicine

    Science.gov (United States)

    Kuznetsov, D. N.; Syryamkin, V. I.

    2015-11-01

    Modern technologies play a very important role in our lives. It is hard to imagine how people can get along without personal computers, and companies - without powerful computer centers. Nowadays, many devices make modern medicine more effective. Medicine is developing constantly, so introduction of robots in this sector is a very promising activity. Advances in technology have influenced medicine greatly. Robotic surgery is now actively developing worldwide. Scientists have been carrying out research and practical attempts to create robotic surgeons for more than 20 years, since the mid-80s of the last century. Robotic assistants play an important role in modern medicine. This industry is new enough and is at the early stage of development; despite this, some developments already have worldwide application; they function successfully and bring invaluable help to employees of medical institutions. Today, doctors can perform operations that seemed impossible a few years ago. Such progress in medicine is due to many factors. First, modern operating rooms are equipped with up-to-date equipment, allowing doctors to make operations more accurately and with less risk to the patient. Second, technology has enabled to improve the quality of doctors' training. Various types of robots exist now: assistants, military robots, space, household and medical, of course. Further, we should make a detailed analysis of existing types of robots and their application. The purpose of the article is to illustrate the most popular types of robots used in medicine.

  10. Multi-robot caravanning

    KAUST Repository

    Denny, Jory; Giese, Andrew; Mahadevan, Aditya; Marfaing, Arnaud; Glockenmeier, Rachel; Revia, Colton; Rodriguez, Samuel; Amato, Nancy M.

    2013-01-01

    of waypoints. At the heart of our algorithm is the use of leader election to efficiently exploit the unique environmental knowledge available to each robot in order to plan paths for the group, which makes it general enough to work with robots that have

  11. Reflection on robotic intelligence

    NARCIS (Netherlands)

    Bartneck, C.

    2006-01-01

    This paper reflects on the development or robots, both their physical shape as well as their intelligence. The later strongly depends on the progress made in the artificial intelligence (AI) community which does not yet provide the models and tools necessary to create intelligent robots. It is time

  12. Robots Cannot Lie

    DEFF Research Database (Denmark)

    Borggreen, Gunhild

    2014-01-01

    En analyse af den japanske robot-menneske teaterstykke Hataraku Watashi med fokus på Austins og Butlers begreb om performativitet.......En analyse af den japanske robot-menneske teaterstykke Hataraku Watashi med fokus på Austins og Butlers begreb om performativitet....

  13. Intelligent robot action planning

    Energy Technology Data Exchange (ETDEWEB)

    Vamos, T; Siegler, A

    1982-01-01

    Action planning methods used in intelligent robot control are discussed. Planning is accomplished through environment understanding, environment representation, task understanding and planning, motion analysis and man-machine communication. These fields are analysed in detail. The frames of an intelligent motion planning system are presented. Graphic simulation of the robot's environment and motion is used to support the planning. 14 references.

  14. Robot Vision Library

    Science.gov (United States)

    Howard, Andrew B.; Ansar, Adnan I.; Litwin, Todd E.; Goldberg, Steven B.

    2009-01-01

    The JPL Robot Vision Library (JPLV) provides real-time robot vision algorithms for developers who are not vision specialists. The package includes algorithms for stereo ranging, visual odometry and unsurveyed camera calibration, and has unique support for very wideangle lenses

  15. Innovations in robotic surgery.

    Science.gov (United States)

    Gettman, Matthew; Rivera, Marcelino

    2016-05-01

    Developments in robotic surgery have continued to advance care throughout the field of urology. The purpose of this review is to evaluate innovations in robotic surgery over the past 18 months. The release of the da Vinci Xi system heralded an improvement on the Si system with improved docking, the ability to further manipulate robotic arms without clashing, and an autofocus universal endoscope. Robotic simulation continues to evolve with improvements in simulation training design to include augmented reality in robotic surgical education. Robotic-assisted laparoendoscopic single-site surgery continues to evolve with improvements on technique that allow for tackling previously complex pathologic surgical anatomy including urologic oncology and reconstruction. Last, innovations of new surgical platforms with robotic systems to improve surgeon ergonomics and efficiency in ureteral and renal surgery are being applied in the clinical setting. Urologic surgery continues to be at the forefront of the revolution of robotic surgery with advancements in not only existing technology but also creation of entirely novel surgical systems.

  16. Infant discrimination of humanoid robots

    Directory of Open Access Journals (Sweden)

    Goh eMatsuda

    2015-09-01

    Full Text Available Recently, extremely humanlike robots called androids have been developed, some of which are already being used in the field of entertainment. In the context of psychological studies, androids are expected to be used in the future as fully controllable human stimuli to investigate human nature. In this study, we used an android to examine infant discrimination ability between human beings and non-human agents. Participants (N = 42 infants were assigned to three groups based on their age, i.e., 6- to 8-month-olds, 9- to 11-month-olds, and 12- to 14-month-olds, and took part in a preferential looking paradigm. Of three types of agents involved in the paradigm—a human, an android modeled on the human, and a mechanical-looking robot made from the android—two at a time were presented side-by-side as they performed a grasping action. Infants’ looking behavior was measured using an eye tracking system, and the amount of time spent focusing on each of three areas of interest (face, goal, and body was analyzed. Results showed that all age groups predominantly looked at the robot and at the face area, and that infants aged over 9 months watched the goal area for longer than the body area. There was no difference in looking times and areas focused on between the human and the android. These findings suggest that 6- to 14-month-olds are unable to discriminate between the human and the android, although they can distinguish the mechanical robot from the human.

  17. Introduction to autonomous manipulation case study with an underwater robot, SAUVIM

    CERN Document Server

    Marani, Giacomo

    2014-01-01

    “Autonomous manipulation” is a challenge in robotic technologies. It refers to the capability of a mobile robot system with one or more manipulators that performs intervention tasks requiring physical contacts in unstructured environments and without continuous human supervision. Achieving autonomous manipulation capability is a quantum leap in robotic technologies as it is currently beyond the state of the art in robotics. This book addresses issues with the complexity of the problems encountered in autonomous manipulation including representation and modeling of robotic structures, kinematic and dynamic robotic control, kinematic and algorithmic singularity avoidance, dynamic task priority, workspace optimization and environment perception. Further development in autonomous manipulation should be able to provide robust improvements of the solutions for all of the above issues. The book provides an extensive tract on sensory-based autonomous manipulation for intervention tasks in unstructured environment...

  18. Social Intelligence for a Robot Engaging People in Cognitive Training Activities

    Directory of Open Access Journals (Sweden)

    Jeanie Chan

    2012-10-01

    Full Text Available Current research supports the use of cognitive training interventions to improve the brain functioning of both adults and children. Our work focuses on exploring the potential use of robot assistants to allow for these interventions to become more accessible. Namely, we aim to develop an intelligent, socially assistive robot that can engage individuals in person-centred cognitively stimulating activities. In this paper, we present the design of a novel control architecture for the robot Brian 2.0, which enables the robot to be a social motivator by providing assistance, encouragement and celebration during an activity. A hierarchical reinforcement learning approach is used in the architecture to allow the robot to: 1 learn appropriate assistive behaviours based on the structure of the activity, and 2 personalize an interaction based on user states. Experiments show that the control architecture is effective in determining the robot's optimal assistive behaviours during a memory game interaction.

  19. Benefits and problems of health-care robots in aged care settings: A comparison trial.

    Science.gov (United States)

    Broadbent, Elizabeth; Kerse, Ngaire; Peri, Kathryn; Robinson, Hayley; Jayawardena, Chandimal; Kuo, Tony; Datta, Chandan; Stafford, Rebecca; Butler, Haley; Jawalkar, Pratyusha; Amor, Maddy; Robins, Ben; MacDonald, Bruce

    2016-03-01

    This study investigated whether multiple health-care robots could have any benefits or cause any problems in an aged care facility. Fifty-three residents and 53 staff participated in a non-randomised controlled trial over 12 weeks. Six robots provided entertainment, communication and health-monitoring functions in staff rooms and activity lounges. These settings were compared to control settings without robots. There were no significant differences between groups in resident or staff outcomes, except a significant increase in job satisfaction in the control group only. The intervention group perceived the robots had more agency and experience than the control group did. Perceived agency of the robots decreased over time in both groups. Overall, we received very mixed responses with positive, neutral and negative comments. The robots had no major benefits or problems. Future research could give robots stronger operational roles, use more specific outcome measures, and perform cost-benefit analyses. © 2015 AJA Inc.

  20. Robot skills for manufacturing

    DEFF Research Database (Denmark)

    Pedersen, Mikkel Rath; Nalpantidis, Lazaros; Andersen, Rasmus Skovgaard

    2016-01-01

    -asserting robot skills for manufacturing. We show how a relatively small set of skills are derived from current factory worker instructions, and how these can be transferred to industrial mobile manipulators. General robot skills can not only be implemented on these robots, but also be intuitively concatenated...... products are introduced by manufacturers. In order to compete on global markets, the factories of tomorrow need complete production lines, including automation technologies that can effortlessly be reconfigured or repurposed, when the need arises. In this paper we present the concept of general, self...... in running production facilities at an industrial partner. It follows from these experiments that the use of robot skills, and associated task-level programming framework, is a viable solution to introducing robots that can intuitively and on the fly be programmed to perform new tasks by factory workers....