WorldWideScience

Sample records for internal stress distributions

  1. Measurement of probability distributions for internal stresses in dislocated crystals

    Energy Technology Data Exchange (ETDEWEB)

    Wilkinson, Angus J.; Tarleton, Edmund; Vilalta-Clemente, Arantxa; Collins, David M. [Department of Materials, University of Oxford, Parks Road, Oxford OX1 3PH (United Kingdom); Jiang, Jun; Britton, T. Benjamin [Department of Materials, Imperial College London, Royal School of Mines, Exhibition Road, London SW7 2AZ (United Kingdom)

    2014-11-03

    Here, we analyse residual stress distributions obtained from various crystal systems using high resolution electron backscatter diffraction (EBSD) measurements. Histograms showing stress probability distributions exhibit tails extending to very high stress levels. We demonstrate that these extreme stress values are consistent with the functional form that should be expected for dislocated crystals. Analysis initially developed by Groma and co-workers for X-ray line profile analysis and based on the so-called “restricted second moment of the probability distribution” can be used to estimate the total dislocation density. The generality of the results are illustrated by application to three quite different systems, namely, face centred cubic Cu deformed in uniaxial tension, a body centred cubic steel deformed to larger strain by cold rolling, and hexagonal InAlN layers grown on misfitting sapphire and silicon carbide substrates.

  2. Internal stress distribution for generating closure domains in laser-irradiated Fe–3%Si(110) steels

    International Nuclear Information System (INIS)

    Iwata, Keiji; Imafuku, Muneyuki; Orihara, Hideto; Sakai, Yusuke; Ohya, Shin-Ichi; Suzuki, Tamaki; Shobu, Takahisa; Akita, Koichi; Ishiyama, Kazushi

    2015-01-01

    Internal stress distribution for generating closure domains occurring in laser-irradiated Fe–3%Si(110) steels was investigated using high-energy X-ray analysis and domain theory based on the variational principle. The measured triaxial stresses inside the specimen were compressive and the stress in the rolling direction became more dominant than stresses in the other directions. The calculations based on the variational principle of magnetic energy for closure domains showed that the measured triaxial stresses made the closure domains more stable than the basic domain without closure domains. The experimental and calculation results reveal that the laser-introduced internal stresses result in the occurrence of the closure domains

  3. Photoelastic Studies of Internal Stress Distributions of Unidirectional Composites.

    Science.gov (United States)

    1980-12-01

    34 verre a, If t nece, e.ry and Identify by block number) ..... ’Io-dimensional phutoelastli, models were used to determine internal taading-. and...Secretary of Defense for Research and Engineering, le Pe, ,tagon,, Uashington, D.C. 10301 ]2 Commandr, T)efens. lecn, ical Information Center, Cameron

  4. Influence of Transformation Plasticity on the Distribution of Internal Stress in Three Water-Quenched Cylinders

    Science.gov (United States)

    Liu, Yu; Qin, Shengwei; Zhang, Jiazhi; Wang, Ying; Rong, Yonghua; Zuo, Xunwei; Chen, Nailu

    2017-10-01

    Based on the hardenability of three medium carbon steels, cylinders with the same 60-mm diameter and 240-mm length were designed for quenching in water to obtain microstructures, including a pearlite matrix (Chinese steel mark: 45), a bainite matrix (42CrMo), and a martensite matrix (40CrNiMo). Through the combination of normalized functions describing transformation plasticity (TP), the thermo-elasto-plastic constitutive equation was deduced. The results indicate that the finite element simulation (FES) of the internal stress distribution in the three kinds of hardenable steel cylinders based on the proposed exponent-modified (Ex-Modified) normalized function is more consistent with the X-ray diffraction (XRD) measurements than those based on the normalized functions proposed by Abrassart, Desalos, and Leblond, which is attributed to the fact that the Ex-Modified normalized function better describes the TP kinetics. In addition, there was no significant difference between the calculated and measured stress distributions, even though TP was taken into account for the 45 carbon steel; that is, TP can be ignored in FES. In contrast, in the 42CrMo and 40CrNiMo alloyed steels, the significant effect of TP on the residual stress distributions was demonstrated, meaning that TP must be included in the FES. The rationality of the preceding conclusions was analyzed. The complex quenching stress is a consequence of interactions between the thermal and phase transformation stresses. The separated calculations indicate that the three steels exhibit similar thermal stress distributions for the same water-quenching condition, but different phase transformation stresses between 45 carbon steel and alloyed steels, leading to different distributions of their axial and tangential stresses.

  5. Tungsten heavy metal alloys relations between the crystallographic texture and the internal stress distribution

    International Nuclear Information System (INIS)

    Nicolas, G.; Voltz, M.

    2001-01-01

    Quite often the W-Ni-Fe-Co heavy alloys are subjected to a thermomechanical processing of swaging and aging in order to obtain the highest possible level of resistance. Within the framework of this plastic deformation on cylindrical parts, the swaging leads to the distribution of morphological and crystallographic texture as well as specific internal stresses. The resulting mechanical characteristics are correlated to structural and sub-structural variations. (author)

  6. Three-Dimensional Finite Element Analysis of the Stress Distribution at the Internal Implant-Abutment Connection.

    Science.gov (United States)

    Cho, Sung-Yong; Huh, Yoon-Hyuk; Park, Chan-Jin; Cho, Lee-Ra

    2016-01-01

    This study investigated stress distribution in four different implant-abutment interface conditions in the internal tapered connection implant system. Four different implant diameters (3.5 mm, 4.0 mm, 4.5 mm, and 5.0 mm) and two abutment types (hexagonal and conical) were simulated. Four unique implant-abutment interface conditions were assumed based on wall thickness, mating surface length, distance to the vertical stop, and abutment shape. Axial and oblique loading was applied during abutment screw preload, and the Von Mises stresses were measured at the implant-abutment and abutment-screw interfaces. The implant-abutment interface stress decreased as the wall thickness increased. As the mating surface increased, the stress distribution trended downward, and when the distance to the implant vertical stop was 0 μm, the Von Mises stress was extremely high at the vertical stop. Despite their different shapes, the abutments showed similar stress distributions. However, the maximum Von Mises stress was higher in the conical connection than in the hexagonal connection, particularly at the contralateral side to loading. To decrease the stress distribution at the implant-abutment interface, the implant wall thickness, mating surface contact length, distance to the vertical stop, and abutment shape should be carefully considered.

  7. Internal Stress Distribution Measurement of TIG Welded SUS304 Samples Using Neutron Diffraction Technique

    Science.gov (United States)

    Muslih, M. Refai; Sumirat, I.; Sairun; Purwanta

    2008-03-01

    The distribution of residual stress of SUS304 samples that were undergone TIG welding process with four different electric currents has been measured. The welding has been done in the middle part of the samples that was previously grooved by milling machine. Before they were welded the samples were annealed at 650 degree Celsius for one hour. The annealing process was done to eliminate residual stress generated by grooving process so that the residual stress within the samples was merely produced from welding process. The calculation of distribution of residual stress was carried out by measuring the strains within crystal planes of Fe(220) SUS304. Strain, Young modulus, and Poisson ratio of Fe(220) SUS304 were measured using DN1-M neutron diffractometer. Young modulus and Poisson ratio of Fe(220) SUS304 sample were measured in-situ. The result of calculations showed that distribution of residual stress of SUS304 in the vicinity of welded area is influenced both by treatments given at the samples-making process and by the electric current used during welding process.

  8. Three-Dimensional Finite Element Analysis on Stress Distribution of Internal Implant-Abutment Engagement Features.

    Science.gov (United States)

    Cho, Sung-Yong; Huh, Yun-Hyuk; Park, Chan-Jin; Cho, Lee-Ra

    To investigate the stress distribution in an implant-abutment complex with a preloaded abutment screw by comparing implant-abutment engagement features using three-dimensional finite element analysis (FEA). For FEA modeling, two implants-one with a single (S) engagement system and the other with a double (D) engagement system-were placed in the human mandibular molar region. Two types of abutments (hexagonal, conical) were connected to the implants. Different implant models (a single implant, two parallel implants, and mesial and tilted distal implants with 1-mm bone loss) were assumed. A static axial force and a 45-degree oblique force of 200 N were applied as the sum of vectors to the top of the prosthetic occlusal surface with a preload of 30 Ncm in the abutment screw. The von Mises stresses at the implant-abutment and abutment-screw interfaces were measured. In the single implant model, the S-conical abutment type exhibited broader stress distribution than the S-hexagonal abutment. In the double engagement system, the stress concentration was high in the lower contact area of the implant-abutment engagement. In the tilted implant model, the stress concentration point was different from that in the parallel implant model because of the difference in the bone level. The double engagement system demonstrated a high stress concentration at the lower contact area of the implant-abutment interface. To decrease the stress concentration, the type of engagement features of the implant-abutment connection should be carefully considered.

  9. Internal stress distribution of X-ring using photoelastic experimental hybrid method

    Energy Technology Data Exchange (ETDEWEB)

    Bernard, Alunda Ouma [Dedan Kimathi University of Technology, Nyeri (Kenya); Hawong, Jai Sug; Lim, Hyun Seok [Yeungnam University, Gyeongsan (Korea, Republic of); Shin, Dong Chul [Koje College, Geoje (Korea, Republic of)

    2014-05-15

    Sealing elements are essential parts of many machines, and are used to prevent the loss of a fluid or gas. When such fluids are not properly sealed, catastrophic failures may result. Many different types of rings have been developed to suit various industrial needs. Considerable research has been done on the O-ring. We analyze the internal stresses developed in an X-ring under a uniform squeeze rate of 20%, which is suitable for static applications, using a photoelastic experimental hybrid method. The internal pressures applied were 0.98, 1.96, 2.94, 3.92, 4.90, and 5.88 MPa. We show that sealing rings with X geometry have considerably higher internal stresses than O-ring seals. In addition, we demonstrate that after extrusion, for an internal pressure of 5.88 MPa, the two lobes on the upper contact surface merge, thereby increasing the contact length of the upper side significantly. Extrusion in the X-ring occurred when the internal pressure was 4.90 MPa.

  10. T-stresses for internally cracked components

    International Nuclear Information System (INIS)

    Fett, T.

    1997-12-01

    The failure of cracked components is governed by the stresses in the vicinity of the crack tip. The singular stress contribution is characterised by the stress intensity factor K, the first regular stress term is represented by the so-called T-stress. T-stress solutions for components containing an internal crack were computed by application of the Bundary Collocation Method (BCM). The results are compiled in form of tables or approximative relations. In addition a Green's function of T-stresses is proposed for internal cracks which enables to compute T-stress terms for any given stress distribution in the uncracked body. (orig.) [de

  11. Distribution of steady state temperatures and thermoelastic stresses in a cylindrical shell with internal heat generation and cooled on both sides or only on one side

    International Nuclear Information System (INIS)

    Melese d'Hospital, G.B.

    1979-10-01

    General expressions for steady state temperatures and elastic thermal stress distributions are derived for a hollow fuel element cooled on both sides. The main simplifying assumptions consist of one dimensional heat transfer and a single medium. Dimensionless numerical results are plotted in the case of uniform internal heat generation and for constant thermal conductivity. Solid rods and flat plates are treated as special cases. As could be expected, cooling on both sides rather than on only one side, leads to significant reduction in maximum fuel temperature and thermal stresses for a given power density, or to a significant increase in power density for either given maximum temperature drop in the fuel or for maximum tensile thermal stress. Typically, for a rod diameter ratio of 2, the power density could be increased by a factor of 3 to 4 without increasing the maximum stress. Similarly, for the same power density, replacing internal cooling of a hollow fuel element by external cooling reduces the maximum fuel temperature drop by a factor of 1.5 and the average fuel temperature drop (or maximum tensile stress) by a factor of 2, with the same maximum compressive stress

  12. The multi-layered ring under parabolic distribution of radial stresses combined with uniform internal and external pressure

    Directory of Open Access Journals (Sweden)

    Christos F. Markides

    2017-04-01

    Full Text Available A recently introduced solution for the stress- and displacement-fields, developed in a multi-layered circular ring, composed of a finite number of linearly elastic concentric layers, subjected to a parabolic distribution of ra-dial stresses, is here extended to encompass a more general loading scheme, closer to actual conditions. The loading scheme includes, besides the para¬-bolic radial stresses, a combination of uniform pressures acting along the outer- and inner- most boundaries of the layered ring. The analytic solution of the problem is achieved by adopting Savin’s pioneering approach for an infinite plate with a hole strengthened by rings. Taking advantage of the results provided by the ana¬lytic solution, a numerical model, simulating the configuration of a three-layered ring (quite commonly encountered in practic¬al applications is validated. The numerical model is then used for a parametric analysis enlightening some crucial aspects of the overall response of the ring.

  13. Stress State of Elastic Thick-Walled Ring With Self-Balanced Pressures Distributed on Its Internal and External Borders

    Directory of Open Access Journals (Sweden)

    Kravchuk Aleksandr Stepanovich

    2015-10-01

    Full Text Available For the first time with the help of the theory of analytic functions and Kolosov-Muskhelishvili formulas the problem of the two-dimensional theory of elasticity for a thickwalled ring with the uneven pressures, acting on its borders, was solved. The pressure on the inner and outer boundaries is represented by Fourier series. The authors represent the two complex functions which solve boundary problem in the form of Laurent series. The logarithmic terms in these series are absent because the boundary problem has the self-balancing loads on each boundary of ring. The coefficients in the Laurent series are calculated by the boundary conditions. Firstly, the equations were obtained in the general form. But the hypothesis about even distributions of pressures at borders of ring was used for constructing an example. It leads to the fact that all coefficients of analytic functions represented in Laurent series have to be only real. As a solving example, the representation of pressures in equivalent hypotrochoids was used. The application of the computer algebra system Mathematica greatly simplifies the calculation of the distribution of stresses and displacements in ring. It does not require manual formal separation of real and imaginary parts in terms of Kolosov-Muskhelishvili to display the distribution of the physical parameters. It separates them only for calculated numbers with the help of built-in functions.

  14. Temperature distribution and thermal stress

    Indian Academy of Sciences (India)

    Abstract. Thermal effects of a double-end-pumped cubic Nd:YVO4 laser crystal are investigated in this paper. A detailed analysis of temperature distribution and thermal stress in cubic crystal with circular shape pumping is discussed. It has been shown that by considering the total input powers as constant, the ...

  15. Bayesian Prior Probability Distributions for Internal Dosimetry

    Energy Technology Data Exchange (ETDEWEB)

    Miller, G.; Inkret, W.C.; Little, T.T.; Martz, H.F.; Schillaci, M.E

    2001-07-01

    The problem of choosing a prior distribution for the Bayesian interpretation of measurements (specifically internal dosimetry measurements) is considered using a theoretical analysis and by examining historical tritium and plutonium urine bioassay data from Los Alamos. Two models for the prior probability distribution are proposed: (1) the log-normal distribution, when there is some additional information to determine the scale of the true result, and (2) the 'alpha' distribution (a simplified variant of the gamma distribution) when there is not. These models have been incorporated into version 3 of the Bayesian internal dosimetric code in use at Los Alamos (downloadable from our web site). Plutonium internal dosimetry at Los Alamos is now being done using prior probability distribution parameters determined self-consistently from population averages of Los Alamos data. (author)

  16. Internal Stress in a Model Elasto-Plastic Fluid

    OpenAIRE

    Ooshida, Takeshi; Sekimoto, Ken

    2004-01-01

    Plastic materials can carry memory of past mechanical treatment in the form of internal stress. We introduce a natural definition of the vorticity of internal stress in a simple two-dimensional model of elasto-plastic fluids, which generates the internal stress. We demonstrate how the internal stress is induced under external loading, and how the presence of the internal stress modifies the plastic behavior.

  17. Internal stress analysis by acoustic polarimetry

    International Nuclear Information System (INIS)

    Rouge, Jean; Robert, Andre

    The associated improvements of acoustics and electronics allow the field of applications relative to the ultrasonic methods to be extended to the non destructive control of materials and structures. Thus, the acoustical polarimetry is a new method allowing the measurement in orientation and intensity of residual or induced internal stresses in metals or other materials [fr

  18. Stress distribution in two-dimensional silos

    Science.gov (United States)

    Blanco-Rodríguez, Rodolfo; Pérez-Ángel, Gabriel

    2018-01-01

    Simulations of a polydispersed two-dimensional silo were performed using molecular dynamics, with different numbers of grains reaching up to 64 000, verifying numerically the model derived by Janssen and also the main assumption that the walls carry part of the weight due to the static friction between grains with themselves and those with the silo's walls. We vary the friction coefficient, the radii dispersity, the silo width, and the size of grains. We find that the Janssen's model becomes less relevant as the the silo width increases since the behavior of the stresses becomes more hydrostatic. Likewise, we get the normal and tangential stress distribution on the walls evidencing the existence of points of maximum stress. We also obtained the stress matrix with which we observe zones of concentration of load, located always at a height around two thirds of the granular columns. Finally, we observe that the size of the grains affects the distribution of stresses, increasing the weight on the bottom and reducing the normal stress on the walls, as the grains are made smaller (for the same total mass of the granulate), giving again a more hydrostatic and therefore less Janssen-type behavior for the weight of the column.

  19. Macro design effects on stress distribution around implants: A photoelastic stress analysis

    Directory of Open Access Journals (Sweden)

    Serhat Emre Ozkir

    2012-01-01

    Conclusion: As there were observable differences between the implant types, straight placed cylindrical implants showed better stress distribution characteristics, while inclined tapering implants had better stress distribution characteristics.

  20. Stress distributions of coils for toroidal magnetic field

    International Nuclear Information System (INIS)

    Kajita, Tateo; Miyamoto, Kenro.

    1976-01-01

    The stress distributions of a D shaped coil and a circular coil are computed by the finite element method. The dependences of the stress distribution on the geometrical parameters of the stress distribution on the geometrical parameters of the coils and supporting methods are examined. The maximum amount of the stress in the D shaped coil is not much smaller than that of the circular one. However, the stress distribution of the D shaped coil becomes much more uniform. The supporting method has as much effect as the geometrical parameters of the coil on the stress distribution. (auth.)

  1. Finite element analysis of thermal stress distribution in different ...

    African Journals Online (AJOL)

    Nigerian Journal of Clinical Practice. Journal Home ... Von Mises and thermal stress distributions were evaluated. Results: In all ... distribution. Key words: Amalgam, finite element method, glass ionomer cement, resin composite, thermal stress ...

  2. Photoelastic stress analysis in mitred bend under internal pressure

    International Nuclear Information System (INIS)

    Sawa, Yoshiaki

    1987-01-01

    The stress analysis and stress relaxation in mitred bend subjected to internal pressure have been studied by means of the photoelastic stress freezing method. The experimental results show that stress concentration occurs in the wedge tip of the intersectional plane and it is considerably influenced by the bent angle. Then, the stress relaxation was obtained by planing the wedge tip. (author)

  3. Finite Element Simulation and Experimental Verification of Internal Stress of Quenched AISI 4140 Cylinders

    Science.gov (United States)

    Liu, Yu; Qin, Shengwei; Hao, Qingguo; Chen, Nailu; Zuo, Xunwei; Rong, Yonghua

    2017-03-01

    The study of internal stress in quenched AISI 4140 medium carbon steel is of importance in engineering. In this work, the finite element simulation (FES) was employed to predict the distribution of internal stress in quenched AISI 4140 cylinders with two sizes of diameter based on exponent-modified (Ex-Modified) normalized function. The results indicate that the FES based on Ex-Modified normalized function proposed is better consistent with X-ray diffraction measurements of the stress distribution than FES based on normalized function proposed by Abrassart, Desalos and Leblond, respectively, which is attributed that Ex-Modified normalized function better describes transformation plasticity. Effect of temperature distribution on the phase formation, the origin of residual stress distribution and effect of transformation plasticity function on the residual stress distribution were further discussed.

  4. Dose distribution following selective internal radiation therapy

    International Nuclear Information System (INIS)

    Fox, R.A.; Klemp, P.F.; Egan, G.; Mina, L.L.; Burton, M.A.; Gray, B.N.

    1991-01-01

    Selective Internal Radiation Therapy is the intrahepatic arterial injection of microspheres labelled with 90Y. The microspheres lodge in the precapillary circulation of tumor resulting in internal radiation therapy. The activity of the 90Y injected is managed by successive administrations of labelled microspheres and after each injection probing the liver with a calibrated beta probe to assess the dose to the superficial layers of normal tissue. Predicted doses of 75 Gy have been delivered without subsequent evidence of radiation damage to normal cells. This contrasts with the complications resulting from doses in excess of 30 Gy delivered from external beam radiotherapy. Detailed analysis of microsphere distribution in a cubic centimeter of normal liver and the calculation of dose to a 3-dimensional fine grid has shown that the radiation distribution created by the finite size and distribution of the microspheres results in an highly heterogeneous dose pattern. It has been shown that a third of normal liver will receive less than 33.7% of the dose predicted by assuming an homogeneous distribution of 90Y

  5. Internal stresses in α-plutonium during deformation

    International Nuclear Information System (INIS)

    Merz, M.D.

    1976-01-01

    Internal stresses were measured in fine grained (2 μm) and coarse grained (20 μm) α-plutonium. In the fine grained metal the internal stress sigmasub(i), which was interpreted as the stress driving recovery processes near grain boundaries, was weakly dependent on applied stress, sigmasub(a). The effective stress, sigmasub(e) = sigma sub(a) - sigmasub(i), which is the stress to move dislocations, increased nearly 1:1 with applied stress, especially at high applied stresses. The strain rate obeyed the relation epsilon=K(T)sigmasub(e)sup(n) where K(T) is a temperature dependent term and n approximately = 3. The recovery rate in fine grained α-plutonium during creep was concluded to be very sensitive to internal stress. The internal stress in α-plutonium with 20 μm grain size was much higher than in the finer grain metal. (Auth.)

  6. Current distribution tomography for determination of internal current density distributions

    International Nuclear Information System (INIS)

    Gailey, P.C.

    1993-01-01

    A method is presented for determination of current densities inside a cylindrical object using measurements of the magnetic fields outside the object. The cross section of the object is discretized with the current assumed constant over each defined region. Magnetic fields outside the object are related to the internal current densities through a geometry matrix which can be inverted to yield a solution for the current densities in terms of the measured fields. The primary limitation of this technique results from singularities in the geometry matrix that arise due to cylindrical symmetry of the problem. Methods for circumventing the singularities to obtain information about the distribution of current densities are discussed. This process of current distribution tomography is designed to determine internal body current densities using measurements of the external magnetic field distribution. It is non-invasive, and relatively simple to implement. Although related to a more general study of magnetic imaging which has been used to investigate endogenous currents in the brain and other parts of the body, it is restricted to currents either applied directly or induced by exposure to an external field. The research is related to public concern about the possibility of health effects resulting from exposure to power frequency electric and magnetic fields

  7. Stress Distribution, Friction and Listeria Propulsion

    Science.gov (United States)

    Prost, Jacques

    2003-03-01

    I will review our work on the physics of listeria propulsion based on an unavoidable elastic analysis of the stress distribution in the actin gel and dynamical boundary conditions (both normal and tangential). I will show in particular that it provides a natural explanation for the symmetry breaking transition occurring with beads (work with K. Sekimoto and F. Julicher), of the saltatory behavior of beads reported by A Bernheim et al (Nature 2002) and of the shape of soft beads (with O. Campas and J.F Joanny). This last analysis proves that, as announced in an earlier paper (F; Gerbal et al Biophys Journal 2000) the rear part of the gel contributes negatively to the motion.

  8. A novel stress distribution analytical model of O-ring seals under different properties of materials

    International Nuclear Information System (INIS)

    Wu, Di; Wang, Shao Ping; Wang, Xing Jian

    2017-01-01

    The elastomeric O-ring seals have been widely used as sealing elements in hydraulic systems. The sealing performance of O-ring seals is related to stress distribution. The stresses distribution depends on the squeeze rate and internal pressure, and would vary with properties of O-ring seals materials. Thus, in order to study the sealing performance of O-ring seals, it is necessary to describe the analytic relationship between stress distribution and properties of O-ring seals materials. For this purpose, a novel Stress distribution analytical model (SDAM) is proposed in this paper. The analytical model utilizes two stress complex functions to describe the stress distribution of O-ring seals. The proposed SDAM can express not only the analytical relationship between stress distribution and Young’s modulus, but also the one between stress distribution and Poisson’s ratio. Finally, compared results between finite element analysis and the SDAM validate that the proposed model can effectively reveal the stress distribution under different properties for O-ring materials

  9. A novel stress distribution analytical model of O-ring seals under different properties of materials

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Di; Wang, Shao Ping; Wang, Xing Jian [School of Automation Science and Electrical Engineering, Beihang University, Beijing (China)

    2017-01-15

    The elastomeric O-ring seals have been widely used as sealing elements in hydraulic systems. The sealing performance of O-ring seals is related to stress distribution. The stresses distribution depends on the squeeze rate and internal pressure, and would vary with properties of O-ring seals materials. Thus, in order to study the sealing performance of O-ring seals, it is necessary to describe the analytic relationship between stress distribution and properties of O-ring seals materials. For this purpose, a novel Stress distribution analytical model (SDAM) is proposed in this paper. The analytical model utilizes two stress complex functions to describe the stress distribution of O-ring seals. The proposed SDAM can express not only the analytical relationship between stress distribution and Young’s modulus, but also the one between stress distribution and Poisson’s ratio. Finally, compared results between finite element analysis and the SDAM validate that the proposed model can effectively reveal the stress distribution under different properties for O-ring materials.

  10. stress distribution in continuo ribution in continuous thin ribution

    African Journals Online (AJOL)

    eobe

    studied stresses in thin-walled box girder bridges but stress distribution walled box girder bridges .... the classical thin plate theory and trigonometric series. Lertsima et al. ..... remedied by applying spline finite strip method. Compared to other ...

  11. Internal stresses in α-plutonium during deformation

    International Nuclear Information System (INIS)

    Merz, M.D.

    1975-01-01

    Internal stresses were measured in fine-grained (2 μm) and coarse-grained (20 μm) α-plutonium. A stress drop technique (strain transient dip test) was used and the measurements were made for applied creep stresses, sigma/sub a/, from 45 MPa (6250 psi) to 207 MPa (30000 psi) and temperatures from 60 to 113 0 C. The internal stress sigma/sub i/ varied from 17 to 84 MPa and had a weak dependence on applied stress. The effective stress, given by sigma/sub e/ = sigma/sub a/-sigma/sub i/, which is associated with the stress to move dislocations, increased nearly one to one with applied stress, especially at high stresses. The strain rate obeyed the relation epsilon = K(T)sigma/sub e//sup n/ where K(T) is a temperature-dependent term given approximately by Kexp (-104 KJ/mol/RT) and n approximately equal to 3. In fine-grained α-plutonium, the internal stress was interpreted as the stress driving recovery processes near grain boundaries. Measurements of internal stress in α- plutonium with 20-μm grain size indicated a much higher internal stress than for the 2-μm grain size. (5 fig) (auth)

  12. Towards a Stress Free Education: International Perspective

    Science.gov (United States)

    Sedere, Upali M.

    2010-01-01

    Stress is simply the body's response to changes that create taxing demands. When one cannot cope with it, these cause distresses. Stress is not always bad. The manageable stress motivates individuals to achieve what he/she wishes to achieve. When one can cope with stress it is called "eustress" which is good. Education in many countries…

  13. Internal stress control of boron thin film

    International Nuclear Information System (INIS)

    Satomi, N.; Kitamura, M.; Sasaki, T.; Nishikawa, M.

    1998-01-01

    The occurrence of stress in thin films has led to serious stability problems in practical use. We have investigated the stress in the boron films to find the deposition condition of the boron films with less stress. It was found that the stress in the boron film varies sufficiently from compressive to tensile stress, that is from -1.0 to 1.4 GPa, depending on the evaporation conditions, such as deposition rate and the substrate temperature. Hydrogen ion bombardment resulted in the enhancement of the compressive stress, possibly due to ion peening effect, while under helium ion bombardment, stress relief was observed. The boron film with nearly zero stress was obtained by the evaporation at a deposition rate of 0.5 nm s -1 and substrate temperature of 300 C. (orig.)

  14. Internal stress control of boron thin film

    Energy Technology Data Exchange (ETDEWEB)

    Satomi, N.; Kitamura, M.; Sasaki, T.; Nishikawa, M. [Osaka Univ., Suita (Japan). Graduate Sch. of Eng.

    1998-09-01

    The occurrence of stress in thin films has led to serious stability problems in practical use. We have investigated the stress in the boron films to find the deposition condition of the boron films with less stress. It was found that the stress in the boron film varies sufficiently from compressive to tensile stress, that is from -1.0 to 1.4 GPa, depending on the evaporation conditions, such as deposition rate and the substrate temperature. Hydrogen ion bombardment resulted in the enhancement of the compressive stress, possibly due to ion peening effect, while under helium ion bombardment, stress relief was observed. The boron film with nearly zero stress was obtained by the evaporation at a deposition rate of 0.5 nm s{sup -1} and substrate temperature of 300 C. (orig.) 12 refs.

  15. Internal stresses in an austeno-ferritic duplex stainless steel

    International Nuclear Information System (INIS)

    Verhaeghe, B.; Brechet, Y.; Louchet, F.; Massoud, J.P.; Touzeau, D.

    1996-04-01

    Austeno-ferritic duplex steels possess microstructures containing comparable volume fractions of hard and soft phases which are bi-percolated. They are therefore liable to develop large internal stresses during straining. The evolution and the relaxation of these stresses and the occurrence of damage are characterized using Bauschinger tests. Thermally aged and non-aged material behaviour are compared. Plastic flow in the hard phase is shown to be significantly efficient in releasing these internal stresses. (authors). 15 refs., 8 figs

  16. Internal Casting Stresses and Dimensional Stability

    DEFF Research Database (Denmark)

    Andriollo, Tito; Vedel-Smith, Nikolaj Kjelgaard; Thorborg, Jesper

    2017-01-01

    , accelerated stress corrosion, decreased fatigue resistance, and so on. In addition, they can also be responsible for undesirable shape distortions, which may compromise the fulfillment of geometrical tolerance requirements. As a consequence, a good understanding of what residual stresses are, how they form......It is common knowledge that cast iron components may be affected by the presence of residual stresses. This often represents a serious threat, because residual stresses almost invariably cause a significant degradation of the most important material properties, such as reduced fracture toughness...

  17. Use of frozen stress in extracting stress intensity factor distributions in three dimensional cracked body problems

    Science.gov (United States)

    Smith, C. W.

    1992-01-01

    The adaptation of the frozen stress photoelastic method to the determination of the distribution of stress intensity factors in three dimensional problems is briefly reviewed. The method is then applied to several engineering problems of practical significance.

  18. Stress Distribution in Graded Cellular Materials Under Dynamic Compression

    Directory of Open Access Journals (Sweden)

    Peng Wang

    Full Text Available Abstract Dynamic compression behaviors of density-homogeneous and density-graded irregular honeycombs are investigated using cell-based finite element models under a constant-velocity impact scenario. A method based on the cross-sectional engineering stress is developed to obtain the one-dimensional stress distribution along the loading direction in a cellular specimen. The cross-sectional engineering stress is contributed by two parts: the node-transitive stress and the contact-induced stress, which are caused by the nodal force and the contact of cell walls, respectively. It is found that the contact-induced stress is dominant for the significantly enhanced stress behind the shock front. The stress enhancement and the compaction wave propagation can be observed through the stress distributions in honeycombs under high-velocity compression. The single and double compaction wave modes are observed directly from the stress distributions. Theoretical analysis of the compaction wave propagation in the density-graded honeycombs based on the R-PH (rigid-plastic hardening idealization is carried out and verified by the numerical simulations. It is found that stress distribution in cellular materials and the compaction wave propagation characteristics under dynamic compression can be approximately predicted by the R-PH shock model.

  19. Research on stress distribution regularity of cement sheaths of radial well based on ABAQUS

    Science.gov (United States)

    Shi, Jihui; Cheng, Yuanfang; Li, Xiaolong; Xiao, Wen; Li, Menglai

    2017-12-01

    To ensure desirable outcome of hydraulic fracturing based on ultra-short radius radial systems, it is required to investigate the stress distribution regularity and stability of the cement sheath. On the basis of the theoretical model of the cement sheath stress distribution, a reservoir mechanical model was built using the finite element software, ABAQUS, according to the physical property of a certain oil reservoir of the Shengli oilfield. The stress distribution of the casing-cement-sheath-formation system under the practical condition was simulated, based on which analyses were conducted from multiple points of view. Results show that the stress on the internal interface of the cement sheath exceeds that on the external interface, and fluctuates with higher amplitudes, which means that the internal interface is the most failure-prone. The unevenness of the cement sheath stress distribution grows with the increasing horizontal principal stress ratio, and so does the variation magnitude. This indicates that higher horizontal principal stress ratios are unfavourable for the structural stability of the cement sheath. Both the wellbore quantity of the URRS and the physical property of the material can affect the cement sheath distribution. It is suggested to optimize the quantity of the radial wellbore and use cement with a lower elastic modulus and higher Poisson’s ratio. At last, the impact level of the above factor was analysed, with the help of the grey correlation analysis.

  20. Representation of stress distributions inprismatic and cylindrical linear elements

    Directory of Open Access Journals (Sweden)

    Fernando Giménez-Palomares

    2017-08-01

    Full Text Available The  loads  applied  on  a  linear  structural  element  generate  internal  forces  in  the  cross  sections  which,  in turn, result in stresses along the element. The nature, extent and shape of stress distributions are required  parameters  to  compute  the  strength  of  structural  elements  or  machinery  components  in  order  to  its analysis or design. In this work, it is presented a virtual laboratory which allows to obtain different stress distributions  in  an  isostatic  beam,  prismatic  or  cylindrical,  subjected  to  axial  forces,  shear  forces  and bending moments. The virtual laboratory permits a great interactivity, allowing the simulation of various real  situations  in  which  the  user  can  modify  the  magnitude  and  direction  of  acting  loads,  and  also  the boundary conditions of the beam. The ultimate goal of this paper is to present a tool aimed to support the learning and teaching of subjects related to Elasticy and Strength of Materials that are found in bachelor university degrees.

  1. Distribution of incremental static stress caused by earthquakes

    Directory of Open Access Journals (Sweden)

    Y. Y. Kagan

    1994-01-01

    Full Text Available Theoretical calculations, simulations and measurements of rotation of earthquake focal mechanisms suggest that the stress in earthquake focal zones follows the Cauchy distribution which is one of the stable probability distributions (with the value of the exponent α equal to 1. We review the properties of the stable distributions and show that the Cauchy distribution is expected to approximate the stress caused by earthquakes occurring over geologically long intervals of a fault zone development. However, the stress caused by recent earthquakes recorded in instrumental catalogues, should follow symmetric stable distributions with the value of α significantly less than one. This is explained by a fractal distribution of earthquake hypocentres: the dimension of a hypocentre set, ��, is close to zero for short-term earthquake catalogues and asymptotically approaches 2¼ for long-time intervals. We use the Harvard catalogue of seismic moment tensor solutions to investigate the distribution of incremental static stress caused by earthquakes. The stress measured in the focal zone of each event is approximated by stable distributions. In agreement with theoretical considerations, the exponent value of the distribution approaches zero as the time span of an earthquake catalogue (ΔT decreases. For large stress values α increases. We surmise that it is caused by the δ increase for small inter-earthquake distances due to location errors.

  2. HammerCloud: A Stress Testing System for Distributed Analysis

    International Nuclear Information System (INIS)

    Ster, Daniel C van der; García, Mario Úbeda; Paladin, Massimo; Elmsheuser, Johannes

    2011-01-01

    Distributed analysis of LHC data is an I/O-intensive activity which places large demands on the internal network, storage, and local disks at remote computing facilities. Commissioning and maintaining a site to provide an efficient distributed analysis service is therefore a challenge which can be aided by tools to help evaluate a variety of infrastructure designs and configurations. HammerCloud is one such tool; it is a stress testing service which is used by central operations teams, regional coordinators, and local site admins to (a) submit arbitrary number of analysis jobs to a number of sites, (b) maintain at a steady-state a predefined number of jobs running at the sites under test, (c) produce web-based reports summarizing the efficiency and performance of the sites under test, and (d) present a web-interface for historical test results to both evaluate progress and compare sites. HammerCloud was built around the distributed analysis framework Ganga, exploiting its API for grid job management. HammerCloud has been employed by the ATLAS experiment for continuous testing of many sites worldwide, and also during large scale computing challenges such as STEP'09 and UAT'09, where the scale of the tests exceeded 10,000 concurrently running and 1,000,000 total jobs over multi-day periods. In addition, HammerCloud is being adopted by the CMS experiment; the plugin structure of HammerCloud allows the execution of CMS jobs using their official tool (CRAB).

  3. HammerCloud: A Stress Testing System for Distributed Analysis

    CERN Document Server

    van der Ster, Daniel C; Ubeda Garcia, Mario; Paladin, Massimo

    2011-01-01

    Distributed analysis of LHC data is an I/O-intensive activity which places large demands on the internal network, storage, and local disks at remote computing facilities. Commissioning and maintaining a site to provide an efficient distributed analysis service is therefore a challenge which can be aided by tools to help evaluate a variety of infrastructure designs and configurations. HammerCloud (HC) is one such tool; it is a stress testing service which is used by central operations teams, regional coordinators, and local site admins to (a) submit arbitrary number of analysis jobs to a number of sites, (b) maintain at a steady-state a predefined number of jobs running at the sites under test, (c) produce web-based reports summarizing the efficiency and performance of the sites under test, and (d) present a web-interface for historical test results to both evaluate progress and compare sites. HC was built around the distributed analysis framework Ganga, exploiting its API for grid job management. HC has been ...

  4. 76 FR 2711 - Cinram Distribution, LLC, a Subsidiary of Cinram International, Simi Valley Distribution Center...

    Science.gov (United States)

    2011-01-14

    ... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-74,357] Cinram Distribution, LLC, a Subsidiary of Cinram International, Simi Valley Distribution Center, Including On-Site Leased... of Cinram Distribution, LLC, a subsidiary of Cinram International, Simi Valley Distribution Center...

  5. Effect study of multi-bubbles on stress distribution of fuel particle

    International Nuclear Information System (INIS)

    Zhao Yi; Wang Xiaomin; Long Chongsheng

    2015-01-01

    The finite element model was proposed to simulate the process of the UO_2 dispersion fuel particle sustaining the internal pressure of multi-bubbles, and the stress distribution of fuel particle with intra-bubbles was calculated. The results show that when the bubbles line equidistantly along x axis, the max normal stress along y axis increases with the number of bubbles, meanwhile, the increment of the normal stress gradually decreases. There is a limit that the effect of bubble's number imposes on the max normal stress in the fuel particle. When multi-column of bubbles exist, the max normal stress along x axis in the fuel particle increases, and the max normal stress along y axis decreases with the increase of the number of bubble column. The stress concentration in the fuel particle decreases with the spacing radius ratio increasing. (authors)

  6. Thermographic Analysis of Stress Distribution in Welded Joints

    Directory of Open Access Journals (Sweden)

    Domazet Ž.

    2010-06-01

    Full Text Available The fatigue life prediction of welded joints based on S-N curves in conjunction with nominal stresses generally is not reliable. Stress distribution in welded area affected by geometrical inhomogeneity, irregular welded surface and weld toe radius is quite complex, so the local (structural stress concept is accepted in recent papers. The aim of this paper is to determine the stress distribution in plate type aluminum welded joints, to analyze the reliability of TSA (Thermal Stress Analysis in this kind of investigations, and to obtain numerical values for stress concentration factors for practical use. Stress distribution in aluminum butt and fillet welded joints is determined by using the three different methods: strain gauges measurement, thermal stress analysis and FEM. Obtained results show good agreement - the TSA mutually confirmed the FEM model and stresses measured by strain gauges. According to obtained results, it may be stated that TSA, as a relatively new measurement technique may in the future become a standard tool for the experimental investigation of stress concentration and fatigue in welded joints that can help to develop more accurate numerical tools for fatigue life prediction.

  7. Thermographic Analysis of Stress Distribution in Welded Joints

    Science.gov (United States)

    Piršić, T.; Krstulović Opara, L.; Domazet, Ž.

    2010-06-01

    The fatigue life prediction of welded joints based on S-N curves in conjunction with nominal stresses generally is not reliable. Stress distribution in welded area affected by geometrical inhomogeneity, irregular welded surface and weld toe radius is quite complex, so the local (structural) stress concept is accepted in recent papers. The aim of this paper is to determine the stress distribution in plate type aluminum welded joints, to analyze the reliability of TSA (Thermal Stress Analysis) in this kind of investigations, and to obtain numerical values for stress concentration factors for practical use. Stress distribution in aluminum butt and fillet welded joints is determined by using the three different methods: strain gauges measurement, thermal stress analysis and FEM. Obtained results show good agreement - the TSA mutually confirmed the FEM model and stresses measured by strain gauges. According to obtained results, it may be stated that TSA, as a relatively new measurement technique may in the future become a standard tool for the experimental investigation of stress concentration and fatigue in welded joints that can help to develop more accurate numerical tools for fatigue life prediction.

  8. ELASTIC-PLASTIC AND RESIDUAL STRESS ANALYSIS OF AN ALUMINUM DISC UNDER INTERNAL PRESSURES

    Directory of Open Access Journals (Sweden)

    Numan Behlül BEKTAŞ

    2004-02-01

    Full Text Available This paper deals with elastic-plastic stress analysis of a thin aluminum disc under internal pressures. An analytical solution is performed for satisfying elastic-plastic stress-strain relations and boundary conditions for small plastic deformations. The Von-Mises Criterion is used as a yield criterion, and elastic perfectly plastic material is assumed. Elastic-plastic and residual stress distributions are obtained from inner radius to outer radius, and they are presented in tables and figures. All radial stress components, ?r, are compressive, and they are highest at the inner radius. All tangential stress components, ??, are tensile, and they are highest where the plastic deformation begins. Magnitude of the tangential residual stresses is higher than those the radial residual stresses.

  9. Social Support and Acculturative Stress among Korean International Students

    Science.gov (United States)

    Ra, Young-An

    2016-01-01

    Previous studies have reported that international students in the US experience unique difficulties and acculturative stress related to cultural differences, language barriers, academic pressure, and interpersonal relationships (Mallinckrodt & Leong, 1992). Berry, Kim, Minde, and Mok (1987) defined this "acculturative stress" as…

  10. Needs and Acculturative Stress of International Students in CACREP Programs

    Science.gov (United States)

    Behl, Malvika; Laux, John M.; Roseman, Christopher P.; Tiamiyu, Mojisola; Spann, Sammy

    2017-01-01

    International students enrolled in programs accredited by the Council for Accreditation of Counseling and Related Educational Programs provided acculturative stress and needs data. Acculturative stress was correlated with academic, social, language, and cultural needs. Furthermore, relationships were found between students' types of needs.…

  11. Interface topography and residual stress distributions in W coatings for fusion armour applications

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, G. [Department of Materials, University of Oxford, Parks Road, Oxford OX1 3PH (United Kingdom)], E-mail: g.thomas@cranfield.ac.uk; Vincent, R. [Department of Materials, University of Oxford, Parks Road, Oxford OX1 3PH (United Kingdom); Matthews, G. [UKAEA Fusion, K2 Culham Science Centre, Abingdon OX14 3DB (United Kingdom); Dance, B. [TWI Ltd, Granta Park, Great Abingdon, Cambridge CB1 6AL (United Kingdom); Grant, P.S. [Department of Materials, University of Oxford, Parks Road, Oxford OX1 3PH (United Kingdom)

    2008-03-25

    Vacuum plasma sprayed (VPS) tungsten (W) coatings are potential plasma facing components in future fusion power plants. However, the large coefficient of thermal expansion mismatch between W and underlying structural steels and other metallic materials poses a significant problem for manufacturing and service life because of the evolution of large thermally induced stresses leading to failure. In this paper, the effects of the substrate/coating interface 3D geometry on stress distributions are investigated using finite element analysis and VPS experiments to manufacture up to 2 mm thick W coatings. The key factors that affect internal stress distributions during thermal exposure have been identified including graded composition inter-layers, stress concentration effects, mechanical adhesion, and the possible role of segmentation in relieving coating stresses on surface sculptured substrates.

  12. Interface topography and residual stress distributions in W coatings for fusion armour applications

    International Nuclear Information System (INIS)

    Thomas, G.; Vincent, R.; Matthews, G.; Dance, B.; Grant, P.S.

    2008-01-01

    Vacuum plasma sprayed (VPS) tungsten (W) coatings are potential plasma facing components in future fusion power plants. However, the large coefficient of thermal expansion mismatch between W and underlying structural steels and other metallic materials poses a significant problem for manufacturing and service life because of the evolution of large thermally induced stresses leading to failure. In this paper, the effects of the substrate/coating interface 3D geometry on stress distributions are investigated using finite element analysis and VPS experiments to manufacture up to 2 mm thick W coatings. The key factors that affect internal stress distributions during thermal exposure have been identified including graded composition inter-layers, stress concentration effects, mechanical adhesion, and the possible role of segmentation in relieving coating stresses on surface sculptured substrates

  13. 10th International Symposium on Intelligent Distributed Computing

    CERN Document Server

    Seghrouchni, Amal; Beynier, Aurélie; Camacho, David; Herpson, Cédric; Hindriks, Koen; Novais, Paulo

    2017-01-01

    This book presents the combined peer-reviewed proceedings of the tenth International Symposium on Intelligent Distributed Computing (IDC’2016), which was held in Paris, France from October 10th to 12th, 2016. The 23 contributions address a range of topics related to theory and application of intelligent distributed computing, including: Intelligent Distributed Agent-Based Systems, Ambient Intelligence and Social Networks, Computational Sustainability, Intelligent Distributed Knowledge Representation and Processing, Smart Networks, Networked Intelligence and Intelligent Distributed Applications, amongst others.

  14. Isothermal martensitic transformation as an internal-stress-increasing process

    International Nuclear Information System (INIS)

    Liu, Y.; Xie, Z.L.; Haenninen, H.; Humbeeck, J. van; Pietikaeinen, J.

    1995-01-01

    Based on the results that the magnitude of the stabilization of retained austenite increases with increasing the amount of martensite transformed, it has been assumed that the martensitic transformation is accompanied with an increase in internal resisting stress which subsequently results in the stabilization of retained austenite. By simplifying this internal resisting stress to be a type of hydrostatic compressive stress acting on retained austenite due to surrounding martensite plates, a thermodynamical analysis for an isothermal martensitic transformation under applied hydrostatic pressure has been performed. The calculated results, to some extent, show a good agreement with the experimental data. (orig.)

  15. Coping Strategies for Managing Acculturative Stress among Asian International Students

    Science.gov (United States)

    Ra, Young-An; Trusty, Jerry

    2015-01-01

    This article examines the effects of specific coping strategies on managing acculturative stress and acculturation of Asian international students, based on a sample of 220 Asian international students in the U.S. The data were analyzed with hierarchical multiple regression using Baron and Kenny's (1986) mediation procedure. The results supported…

  16. Core stress distribution of phase shifting multimode polymer optical fiber

    International Nuclear Information System (INIS)

    Furukawa, Rei; Matsuura, Motoharu; Nagata, Morio; Mishima, Kenji; Inoue, Azusa; Tagaya, Akihiro; Koike, Yasuhiro

    2013-01-01

    Poly-(methyl methacrylate-co-benzyl methacrylate) polarization-maintaining optical fibers are known for their high response to normal stress. In this report, responses to higher stress levels up to 0.45 MPa were investigated. The stress amplitude and direction in the fiber cross section were calculated and analyzed with a coincident mode-field obtained from the near-field pattern. The stress amplitude varies significantly in the horizontal direction and is considered to create multiple phases, explaining the measurement results. To investigate possible permanent deformation, the core yield point profile was analyzed. Although it largely exceeds the average applied stress, the calculated stress distribution indicates that the core could partially experience stress that exceeds the yield point

  17. A study of stress distribution in elbows mounted on stanchions

    International Nuclear Information System (INIS)

    Basavanhally, N.R.; Tonet, N.

    1983-01-01

    It is a common practice, both in the nuclear and power piping industry, to have integral attachments on piping to either form a restraint or an anchor. For small attachments, such as lugs, one can use the readily available methods (eg., ASME Code Case N-318) to evaluate the local stresses at these attachments. For elbows or curved pipes mounted on stanchions, the evaluation of local stresses is more complex. In the present analysis, a 3D finite element model was implemented to determine the stress intensification factor that can be applied to piping stress under internal pressure and in-plane bending type of loads. The analysis indicates that, for an internal pressure load, in-plane bending is generated. For such supports, a stress intensification factor should be used to account for the increased loads. The results also indicate that there is an optimum elbow to stanchion post radius ratio which should be used in designing such supports. (orig.)

  18. Internal Stresses in Wires for High Field Magnets

    International Nuclear Information System (INIS)

    Han, K.; Embury, J.D.; Lawson, A.C.; Von Dreele, R.B.; Wood, J.T.; Richardson, J.W. Jr.

    1998-01-01

    The codeformation of Cu-Ag or Cu-Nb composite wires used for high field magnets has a number of important microstructural consequences, including the production of very fine scale structures, the development of very high internal surface area to volume ratios during the drawing and the storage of defects at interphase interfaces. In addition, the fabrication and codeformation of phases which differ in crystal structure, thermal expansion, elastic modulus and lattice parameter lead to the development of short wavelength internal stresses. These internal stresses are measured by neutron diffraction and transmission electron microscopy as a function of the imposed drawing strain. The internal stresses lead to important changes in elastic plastic response which can be related to both magnet design and service life and these aspects will be described in detail

  19. Vertical Distribution of Tidal Flow Reynolds Stress in Shallow Sea

    Institute of Scientific and Technical Information of China (English)

    SONG Zhi-yao; NI Zhi-hui; LU Guo-nian

    2009-01-01

    Based on the results of the tidal flow Reynolds stresses of the field observations,indoor experiments,and numerical models,the parabolic distribution of the tidal flow Reynolds stress is proposed and its coefficients are determined theoretically in this paper.Having been well verified with the field data and experimental data,the proposed distribution of Reynolds stress is also compared with numerical model results,and a good agreement is obtained,showing that this distribution can well reflect the basic features of Reynolds stress deviating from the linear distribution that is downward when the tidal flow is of acceleration,upward when the tidal flow is of deceleration.Its dynamics cause is also discussed preliminarily and the influence of the water depth is pointed out from the definition of Reynolds stress,turbulent generation,transmission,and so on.The established expression for the vertical distribution of the tidal flow Reynolds stress is not only simple and explicit,but can also well reflect the features of the tidal flow acceleration and deceleration for further study on the velocity profile of tidal flow.

  20. Risk factors for psychological stress among international business travellers.

    Science.gov (United States)

    Striker, J; Luippold, R S; Nagy, L; Liese, B; Bigelow, C; Mundt, K A

    1999-04-01

    This study investigated sources of self reported psychological stress among international business travellers at the World Bank, following up on a previous study showing that travellers submitted more insurance claims for psychological disorders. Hypotheses were that work, personal, family, and health concerns, as well as time zone travel, contribute to travel stress. A travel survey was developed from focus groups and consisted of questions about these potential sources of travel stress. Surveys were sent to a random sample of staff, stratified by number of travel missions, age range, and sex. Canonical correlation analyses estimated the association between key survey items on sources of stress and two measures of travel stress. 498 staff completed the survey. More than a third reported high to very high travel stress. Correlations between predictors and travel stress showed that social and emotional concerns (such as impact of travel on family and sense of isolation) contributed the most to such stress, followed by health concerns, and workload upon return from travel. Surprisingly, time zone travel did not contribute to the self reported stress of these travellers. There were few modifiers of stress, although respondents suggested that a day of rest after travel and reduced workloads would help. The current study confirms clinical impressions about several correlates of travel stress. Similar research with travellers in other organisations could help to determine whether the findings from this study are valid and what measures can be taken to reduce the psychological health risks to travellers.

  1. Risk factors for psychological stress among international business travellers

    Science.gov (United States)

    Striker, J.; Luippold, R. S.; Nagy, L.; Liese, B.; Bigelow, C.; Mundt, K. A.

    1999-01-01

    OBJECTIVES: This study investigated sources of self reported psychological stress among international business travellers at the World Bank, following up on a previous study showing that travellers submitted more insurance claims for psychological disorders. Hypotheses were that work, personal, family, and health concerns, as well as time zone travel, contribute to travel stress. METHODS: A travel survey was developed from focus groups and consisted of questions about these potential sources of travel stress. Surveys were sent to a random sample of staff, stratified by number of travel missions, age range, and sex. Canonical correlation analyses estimated the association between key survey items on sources of stress and two measures of travel stress. RESULTS: 498 staff completed the survey. More than a third reported high to very high travel stress. Correlations between predictors and travel stress showed that social and emotional concerns (such as impact of travel on family and sense of isolation) contributed the most to such stress, followed by health concerns, and workload upon return from travel. Surprisingly, time zone travel did not contribute to the self reported stress of these travellers. There were few modifiers of stress, although respondents suggested that a day of rest after travel and reduced workloads would help. CONCLUSIONS: The current study confirms clinical impressions about several correlates of travel stress. Similar research with travellers in other organisations could help to determine whether the findings from this study are valid and what measures can be taken to reduce the psychological health risks to travellers.   PMID:10450241

  2. Prediction of residual stress distributions due to surface machining and welding and crack growth simulation under residual stress distribution

    International Nuclear Information System (INIS)

    Ihara, Ryohei; Katsuyama, JInya; Onizawa, Kunio; Hashimoto, Tadafumi; Mikami, Yoshiki; Mochizuki, Masahito

    2011-01-01

    Research highlights: → Residual stress distributions due to welding and machining are evaluated by XRD and FEM. → Residual stress due to machining shows higher tensile stress than welding near the surface. → Crack growth analysis is performed using calculated residual stress. → Crack growth result is affected machining rather than welding. → Machining is an important factor for crack growth. - Abstract: In nuclear power plants, stress corrosion cracking (SCC) has been observed near the weld zone of the core shroud and primary loop recirculation (PLR) pipes made of low-carbon austenitic stainless steel Type 316L. The joining process of pipes usually includes surface machining and welding. Both processes induce residual stresses, and residual stresses are thus important factors in the occurrence and propagation of SCC. In this study, the finite element method (FEM) was used to estimate residual stress distributions generated by butt welding and surface machining. The thermoelastic-plastic analysis was performed for the welding simulation, and the thermo-mechanical coupled analysis based on the Johnson-Cook material model was performed for the surface machining simulation. In addition, a crack growth analysis based on the stress intensity factor (SIF) calculation was performed using the calculated residual stress distributions that are generated by welding and surface machining. The surface machining analysis showed that tensile residual stress due to surface machining only exists approximately 0.2 mm from the machined surface, and the surface residual stress increases with cutting speed. The crack growth analysis showed that the crack depth is affected by both surface machining and welding, and the crack length is more affected by surface machining than by welding.

  3. The measurement of internal stress fields in weldments and around cracks using high resolution neutron diffraction

    International Nuclear Information System (INIS)

    Allen, A.J.; Hutchings, M.T.; Windsor, C.G.

    1987-01-01

    The paper describes and illustrates the capability of neutron diffraction to measure the complete internal lattice macrostrain field, and hence the stress field, within steel components and weldments arising from their fabrication. A brief outline is given of the theory of the neutron method. The experimental considerations are discussed. The method is illustrated by its application to the measurement of the stress distribution in a:- uniaxially stressed mild steel rod, a double - V test weld, a tube-plate weld, and a cracked fatigue test specimen. (U.K.)

  4. Distribution of Stress in Deformation Zone of Niobium Microalloyed Steel

    Science.gov (United States)

    Jandrlić, Ivan; Rešković, Stoja; Brlić, Tin

    2018-07-01

    Microalloyed steels today represent a significant part of total world production and processing of steel. Although widely used, there are scarce data on the stress distribution in the deformation zone of these steels. Research was carried out on two steel grades, both low-carbon structural steels with the same basic chemical composition, with one of them additionally microalloyed with niobium. Differences in the stress distribution in the deformation zone between two tested steels were continuously observed and measured using the methods of digital image correlation and thermography. It has been found out that niobium microalloyed steel has significantly more complex material flow and stress distribution in the deformation zone when compared to the plain low carbon steel.

  5. Distribution of Stress in Deformation Zone of Niobium Microalloyed Steel

    Science.gov (United States)

    Jandrlić, Ivan; Rešković, Stoja; Brlić, Tin

    2018-03-01

    Microalloyed steels today represent a significant part of total world production and processing of steel. Although widely used, there are scarce data on the stress distribution in the deformation zone of these steels. Research was carried out on two steel grades, both low-carbon structural steels with the same basic chemical composition, with one of them additionally microalloyed with niobium. Differences in the stress distribution in the deformation zone between two tested steels were continuously observed and measured using the methods of digital image correlation and thermography. It has been found out that niobium microalloyed steel has significantly more complex material flow and stress distribution in the deformation zone when compared to the plain low carbon steel.

  6. Residual-stress distributions near stainless steel butt weldments

    International Nuclear Information System (INIS)

    Elligson, W.A.; Shack, W.J.

    1978-01-01

    Concern for the integrity of stainless steel butt-weldments in boiling-water-reactor (BWR) piping systems has stimulated study of the conditions that cause stress corrosion cracking (SCC) in the heat-affected zones (HAZ) of the weldments. It is generally agreed that a high stress exceeding the initial yield strength is one of the essential elements for crack initiation. Since design procedures usually ensure that load stresses are below initial yield, the source of the high stresses necessary to produce SCC is thought to be the residual stresses due to welding. To examine the level of residual stresses in the weldments of interest, bulk residual stresses were measured on 100 mm (4-in.) and 254 mm (10-in.) diameter Schedule 80 piping weldments using strain relief techniques. Both laboratory welded specimens and field welded specimens from reactors in service were studied. Axial bulk residual stress distributions were obtained at 45 0 intervals around the circumference. At each azimuthal position, the residual stresses were measured at seven axial positions: on the weld centerline and 13, 20, and 25 mm on either side of the weld centerline on both the inside and outside surfaces

  7. Distribution and diversity of flora and fauna in International Institute ...

    African Journals Online (AJOL)

    Distribution and diversity of flora and fauna in International Institute Of Tropical Agriculture (IITA) forest and nature reserve, Ibadan, Oyo state, Nigeria. ... was also sighted in the study site and several other birds which normally winter around the lake. Key words: Ecology, Distribution, Diversity, Forest, Nature Reserve, IITA, ...

  8. Transient Stress Intensity Factors of Functionally Graded Hollow Cylinders with Internal Circumferential Cracks

    Directory of Open Access Journals (Sweden)

    Iman Eshraghi

    Full Text Available Abstract In this paper, transient thermomechanical stress intensity factors for functionally graded cylinders with complete internal circumferential cracks are obtained using the weight function method. The finite difference method is used to calculate the time dependent temperature distribution and thermal stresses along the cylinder thickness. Furthermore, finite element analysis is performed to determine the weight function coefficients and to investigate the accuracy of the predicted stress intensity factors from the weight functions. Variation of the stress intensity factors with time and effects of the material gradation on the results are investigated, as well. It is shown that the proposed technique can be used to accurately predict transient thermomechanical stress intensity factors for functionally graded cylinders with arbitrary material gradation.

  9. Imaging shear stress distribution and evaluating the stress concentration factor of the human eye

    Science.gov (United States)

    Joseph Antony, S.

    2015-03-01

    Healthy eyes are vital for a better quality of human life. Historically, for man-made materials, scientists and engineers use stress concentration factors to characterise the effects of structural non-homogeneities on their mechanical strength. However, such information is scarce for the human eye. Here we present the shear stress distribution profiles of a healthy human cornea surface in vivo using photo-stress analysis tomography, which is a non-intrusive and non-X-ray based method. The corneal birefringent retardation measured here is comparable to that of previous studies. Using this, we derive eye stress concentration factors and the directional alignment of major principal stress on the surface of the cornea. Similar to thermometers being used for monitoring the general health in humans, this report provides a foundation to characterise the shear stress carrying capacity of the cornea, and a potential bench mark for validating theoretical modelling of stresses in the human eye in future.

  10. Acculturative Stress and Adjustment Experiences of Greek International Students

    Science.gov (United States)

    Poulakis, Mixalis; Dike, Craig A.; Massa, Amber C.

    2017-01-01

    This study investigated eight Greek international college students' experiences of acculturation and acculturative stress at a mid-western university in the United States. Semi-structured interviews were conducted with participants and Consensual Qualitative Research methodology was utilized for data analysis to identify contextual themes and…

  11. Macro design effects on stress distribution around implants: a photoelastic stress analysis.

    Science.gov (United States)

    Ozkir, Serhat Emre; Terzioglu, Hakan

    2012-01-01

    Biomechanics is one of the main factors for achieving long-term success of implant supported prostheses. Long-term failures mostly depend on biomechanical complications. It is important to distinguish the effects of macro design of the implants. In this study, the photoelastic response of four different types of implants that were inserted with different angulations were comparatively analyzed. The implant types investigated were screw cylinder (ITI, Straumann AG, Basel, Switzerland), stepped cylinder (Frialit2, Friadent GmbH, Manheim, Germany), root form (Camlog Rootline, Alatatec, Wilshelm, Germany), and cylindrical implant, with micro-threads on the implant neck (Astra, AstraTech, Mölndal, Sweden). In the test models, one of the implants was inserted straight, while the other one was aligned mesially with 15° angles. The superstructures were prepared as single crowns. A 150N loading was applied to the restorations throughout the test. A comparison of the implant designs showed that there were no significant differences between the straight implants; however, between the inclined implants, the most favorable stress distribution was seen with the stepped cylinder implants. The least favorable stress concentration was observed around the root formed implants. Microthreads around the implant neck appeared to be effective in a homogenous stress distribution. Observations showed that misaligned implants caused less stress than straight implants, but the stress concentrations were not homogenous. As there were observable differences between the implant types, straight placed cylindrical implants showed better stress distribution characteristics, while inclined tapering implants had better stress distribution characteristics.

  12. Effect of geometric construction on residual stress distribution in designing a nuclear rotor joined by multipass narrow gap welding

    International Nuclear Information System (INIS)

    Tan, Long; Zhang, Linjie; Zhang, Jianxun; Zhuang, Dong

    2014-01-01

    Highlights: • The internal stress of the pipe is measured using local material removal method. • Bottom protrusion at weld seam can release the stress and mitigate stress evolution. The through-wall axial stress is bending type under the effect of the rotor discs. • The impact of geometric construction on the stress evolution begins after pass 15. - Abstract: The purpose of this study is to investigate the effect of geometric construction on the distribution of residual stresses before and after heat treatment in designing a nuclear welded rotor. The local material removal method was used to measure internal residual stress of the experimental pipe after post weld heat treatment. Three finite element models were employed as follows: a model of experimental pipe, a model with a bottom protrusion existed at the weld region, and a model of two rotor discs butt-welded with a bottom protrusion at the weld region. Investigated results showed that the bottom protrusion existed at the weld region can decrease the residual stress and mitigate the stress evolution significantly on the inner surface. Under the binding effect of the rotor discs, the axial stress of inner surface region is compressive stress; the through-wall axial stress at the weld center line can be deemed to a bending type; both the hoop stress and axial stress at the weld center line on the inner surface are compressive. The impact of geometric construction on the stress evolution at the root bead begins after pass 15 deposited

  13. 9th International Symposium on Intelligent Distributed Computing

    CERN Document Server

    Camacho, David; Analide, Cesar; Seghrouchni, Amal; Badica, Costin

    2016-01-01

    This book represents the combined peer-reviewed proceedings of the ninth International Symposium on Intelligent Distributed Computing – IDC’2015, of the Workshop on Cyber Security and Resilience of Large-Scale Systems – WSRL’2015, and of the International Workshop on Future Internet and Smart Networks – FI&SN’2015. All the events were held in Guimarães, Portugal during October 7th-9th, 2015. The 46 contributions published in this book address many topics related to theory and applications of intelligent distributed computing, including: Intelligent Distributed Agent-Based Systems, Ambient Intelligence and Social Networks, Computational Sustainability, Intelligent Distributed Knowledge Representation and Processing, Smart Networks, Networked Intelligence and Intelligent Distributed Applications, amongst others.

  14. Market risk stress testing for internationally active financial institutions

    Directory of Open Access Journals (Sweden)

    Marković Petar

    2011-01-01

    Full Text Available The paper develops a comprehensive framework for market risk stress testing in internationally active financial institutions. We begin by defining the scope and type of the stress test and explaining how to select risk factors and the stress time horizon. We then address challenges related to data gathering, followed by in-depth discussion of techniques for developing realistic shock scenarios. Next the process of shock application to a particular portfolio is described, followed by determination of portfolio profit and loss. We conclude by briefly discussing the issue of assigning probability to stress scenarios. We illustrate the framework by considering the development of a ‘worst case’ scenario using global financial market data from Thomson Reuters Datastream.

  15. Stress concentration factors for an internally pressurized circular vessel containing a radial U-notch

    International Nuclear Information System (INIS)

    Carvalho, E.A. de

    2005-01-01

    This paper evaluates the stress concentration factors for an internally pressurized cylinder containing a radial U-notch along its length. This work studies the cases where the external to internal radius ratio (Ψ) is equal to 1.26, 1.52, 2.00, and 3.00 and the notch radius to internal radius ratio (Φ) is fixed and equal to 0.026. The U-notch depth varies from 0.1 to 0.6 of the wall thickness. Results are also presented for a fixed size semi-circular notch. Hoop stresses at the external wall are presented, showing regions where the stress matches the nominal one and the favourable places to install strain sensors. The finite element method is used to determine the stress concentration factors (K t ) for the above described situations and for a special case where a varying semi-circular notch is present with Ψ=3.00. This notch depth varies from 0.013 to 0.3 of the wall thickness. It is pointed out that even relatively small notches introduce large stress concentrations and disrupt the hoop stress distribution all over the cross section. Results are also compared to an example found in the literature for semi-circular notches and K t curves for both cases present the same shape

  16. Simulation of Stress Distribution in a Thick- Walled Bushing Produced by Die-Casting

    Directory of Open Access Journals (Sweden)

    Pisarek B.P.

    2017-12-01

    Full Text Available Metallographic investigations and a computer simulation of stresses in a gravity die-casting bushing were performed. Simulation of the casting process, solidification of the thick-walled bushing and calculations of the stress was performed using MAGMA5.3 software. The size variability of phases κII affecting the formation of phase stresses σf, depending on the location of the metallographic test area, was identified. The distribution of thermal σt and shrinkage stresses σs, depending on the location of the control point SC in the bushing's volume, was estimated. Probably the nature of these stresses will change slightly even after machining. This can cause variations in operating characteristics (friction coefficient, wear. Due to the strong inhomogeneity of the stress distribution in the bushing's casting, it is necessary to perform further tests of the possibility to conduct thermal treatment guaranteeing homogenization of the internal stresses in the casting, as well as to introduce changes in the bushing' s construction and the casting technology. The paper presents the continuation of the results of research aimed at identifying the causes of defects in the thick-walled bushing, die-casting made of CuAl10Fe5Ni5Cr aluminium bronze.

  17. Evaluation of the stress distribution on the pressure vessel head with multi-openings

    Energy Technology Data Exchange (ETDEWEB)

    Kim, K.S.; Kim, T.W.; Jeong, K.H.; Lee, G.M. [Korea Atomic Energy Research Institute, Taejon (Korea)

    1998-06-01

    This report discusses and analyzes the stress distribution on the pressure vessel head with multi-openings(3 PSV nozzles, 2 SDS nozzles and 1 Man Way) according to patterns of the opening distance. The pressurizer of Korea Standardized Nuclear Power Plant(Ulchin 3 and 4), which meets requirements of the cyclic operation and opening design defined by ASME code, was used as the basic model for that. Stress changes according to the distance between openings were investigated and the factors which should be considered for the opening design were analyzed. Also, the nozzle loads at Level A, B conditions and internal pressure were applied in order to evaluate changes of head stress distributions due to nozzle loads. (author). 6 refs., 29 figs., 4 tabs.

  18. 7th International Symposium on Intelligent Distributed Computing

    CERN Document Server

    Jung, Jason; Badica, Costin

    2014-01-01

    This book represents the combined peer-reviewed proceedings of the Seventh International Symposium on Intelligent Distributed Computing - IDC-2013, of the Second Workshop on Agents for Clouds - A4C-2013, of the Fifth International Workshop on Multi-Agent Systems Technology and Semantics - MASTS-2013, and of the International Workshop on Intelligent Robots - iR-2013. All the events were held in Prague, Czech Republic during September 4-6, 2013. The 41 contributions published in this book address many topics related to theory and applications of intelligent distributed computing and multi-agent systems, including: agent-based data processing, ambient intelligence, bio-informatics, collaborative systems, cryptography and security, distributed algorithms, grid and cloud computing, information extraction, intelligent robotics, knowledge management, linked data, mobile agents, ontologies, pervasive computing, self-organizing systems, peer-to-peer computing, social networks and trust, and swarm intelligence.  .

  19. Study of the stress distribution around an orthotropic bi-material notch tip

    Czech Academy of Sciences Publication Activity Database

    Klusák, Jan; Profant, T.; Kotoul, M.

    417-418, - (2010), s. 385-388 ISSN 1013-9826. [International Conference on Fracture and Damage Mechanics /8./. Malta, 08.09.2009-10.09.2009] R&D Projects: GA ČR GA101/08/0994; GA AV ČR 1QS200410502 Institutional research plan: CEZ:AV0Z20410507 Keywords : Generalized fracture mechanics * Singular stress distribution * Orthotropic bimaterial notch Subject RIV: JL - Materials Fatigue, Friction Mechanics www.scientific.net

  20. Trade and the distributional politics of international labour standards

    OpenAIRE

    Oslington, Paul

    2005-01-01

    This paper constructs a simple general equilibrium model of the trade and distributional effects of spreading advanced country international labour standards to developing countries. Labour standards (including minimum safety requirements, prohibition of prison and child labour, and rights to unionise) are represented as a floor to the cost of employing labour. The model shows how the spread of standards affects the terms of trade and pattern of international specialisation, and can shift ...

  1. The Two Defaults Scenario for Stressing Credit Portfolio Loss Distributions

    Directory of Open Access Journals (Sweden)

    Dirk Tasche

    2015-12-01

    Full Text Available The impact of a stress scenario of default events on the loss distribution of a credit portfolio can be assessed by determining the loss distribution conditional on these events. While it is conceptually easy to estimate loss distributions conditional on default events by means of Monte Carlo simulation, it becomes impractical for two or more simultaneous defaults as then the conditioning event is extremely rare. We provide an analytical approach to the calculation of the conditional loss distribution for the CreditRisk + portfolio model with independent random loss given default distributions. The analytical solution for this case can be used to check the accuracy of an approximation to the conditional loss distribution whereby the unconditional model is run with stressed input probabilities of default (PDs. It turns out that this approximation is unbiased. Numerical examples, however, suggest that the approximation may be seriously inaccurate but that the inaccuracy leads to overestimation of tail losses and, hence, the approach errs on the conservative side.

  2. Stress distribution and topography of Tellus Regio, Venus

    Science.gov (United States)

    Williams, David R.; Greeley, Ronald

    1989-01-01

    The Tellus Regio area of Venus represents a subset of a narrow latitude band where Pioneer Venus Orbiter (PVO) altimetry data, line-of-sight (LOS) gravity data, and Venera 15/16 radar images have all been obtained with good resolution. Tellus Regio also has a wide variety of surface morphologic features, elevations ranging up to 2.5 km, and a relatively low LOS gravity anomaly. This area was therefore chosen in order to examine the theoretical stress distributions resulting from various models of compensation of the observed topography. These surface stress distributions are then compared with the surface morphology revealed in the Venera 15/16 radar images. Conclusions drawn from these comparisons will enable constraints to be put on various tectonic parameters relevant to Tellus Regio. The stress distribution is calculated as a function of the topography, the equipotential anomaly, and the assumed model parameters. The topography data is obtained from the PVO altimetry. The equipotential anomaly is estimated from the PVO LOS gravity data. The PVO LOS gravity represents the spacecraft accelerations due to mass anomalies within the planet. These accelerations are measured at various altitudes and angles to the local vertical and therefore do not lend themselves to a straightforward conversion. A minimum variance estimator of the LOS gravity data is calculated, taking into account the various spacecraft altitudes and LOS angles and using the measured PVO topography as an a priori constraint. This results in an estimated equivalent surface mass distribution, from which the equipotential anomaly is determined.

  3. Stress distribution and topography of Tellus Regio, Venus

    International Nuclear Information System (INIS)

    Williams, D.R.; Greeley, R.

    1989-01-01

    The Tellus Regio area of Venus represents a subset of a narrow latitude band where Pioneer Venus Orbiter (PVO) altimetry data, line-of-sight (LOS) gravity data, and Venera 15/16 radar images have all been obtained with good resolution. Tellus Regio also has a wide variety of surface morphologic features, elevations ranging up to 2.5 km, and a relatively low LOS gravity anomaly. This area was therefore chosen in order to examine the theoretical stress distributions resulting from various models of compensation of the observed topography. These surface stress distributions are then compared with the surface morphology revealed in the Venera 15/16 radar images. Conclusions drawn from these comparisons will enable constraints to be put on various tectonic parameters relevant to Tellus Regio. The stress distribution is calculated as a function of the topography, the equipotential anomaly, and the assumed model parameters. The topography data is obtained from the PVO altimetry. The equipotential anomaly is estimated from the PVO LOS gravity data. The PVO LOS gravity represents the spacecraft accelerations due to mass anomalies within the planet. These accelerations are measured at various altitudes and angles to the local vertical and therefore do not lend themselves to a straightforward conversion. A minimum variance estimator of the LOS gravity data is calculated, taking into account the various spacecraft altitudes and LOS angles and using the measured PVO topography as an a priori constraint. This results in an estimated equivalent surface mass distribution, from which the equipotential anomaly is determined

  4. Intelligent Distributed Computing VI : Proceedings of the 6th International Symposium on Intelligent Distributed Computing

    CERN Document Server

    Badica, Costin; Malgeri, Michele; Unland, Rainer

    2013-01-01

    This book represents the combined peer-reviewed proceedings of the Sixth International Symposium on Intelligent Distributed Computing -- IDC~2012, of the International Workshop on Agents for Cloud -- A4C~2012 and of the Fourth International Workshop on Multi-Agent Systems Technology and Semantics -- MASTS~2012. All the events were held in Calabria, Italy during September 24-26, 2012. The 37 contributions published in this book address many topics related to theory and applications of intelligent distributed computing and multi-agent systems, including: adaptive and autonomous distributed systems, agent programming, ambient assisted living systems, business process modeling and verification, cloud computing, coalition formation, decision support systems, distributed optimization and constraint satisfaction, gesture recognition, intelligent energy management in WSNs, intelligent logistics, machine learning, mobile agents, parallel and distributed computational intelligence, parallel evolutionary computing, trus...

  5. Distributed Autonomous Robotic Systems : the 12th International Symposium

    CERN Document Server

    Cho, Young-Jo

    2016-01-01

    This volume of proceedings includes 32 original contributions presented at the 12th International Symposium on Distributed Autonomous Robotic Systems (DARS 2014), held in November 2014. The selected papers in this volume are authored by leading researchers from Asia, Europe, and the Americas, thereby providing a broad coverage and perspective of the state-of-the-art technologies, algorithms, system architectures, and applications in distributed robotic systems. .

  6. International Review of Standards and Labeling Programs for Distribution Transformers

    Energy Technology Data Exchange (ETDEWEB)

    Letschert, Virginie [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Scholand, Michael [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Carreño, Ana María [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Hernandez, Carolina [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2017-06-20

    Transmission and distribution (T&D) losses in electricity networks represent 8.5% of final energy consumption in the world. In Latin America, T&D losses range between 6% and 20% of final energy consumption, and represent 7% in Chile. Because approximately one-third of T&D losses take place in distribution transformers alone, there is significant potential to save energy and reduce costs and carbon emissions through policy intervention to increase distribution transformer efficiency. A large number of economies around the world have recognized the significant impact of addressing distribution losses and have implemented policies to support market transformation towards more efficient distribution transformers. As a result, there is considerable international experience to be shared and leveraged to inform countries interested in reducing distribution losses through policy intervention. The report builds upon past international studies of standards and labeling (S&L) programs for distribution transformers to present the current energy efficiency programs for distribution transformers around the world.

  7. Stress-strength reliability for general bivariate distributions

    Directory of Open Access Journals (Sweden)

    Alaa H. Abdel-Hamid

    2016-10-01

    Full Text Available An expression for the stress-strength reliability R=P(X1distribution. Such distribution includes bivariate compound Weibull, bivariate compound Gompertz, bivariate compound Pareto, among others. In the parametric case, the maximum likelihood estimates of the parameters and reliability function R are obtained. In the non-parametric case, point and interval estimates of R are developed using Govindarajulu's asymptotic distribution-free method when X1 and X2 are dependent. An example is given when the population distribution is bivariate compound Weibull. Simulation is performed, based on different sample sizes to study the performance of estimates.

  8. Effect of internal stress on the strength of PZT ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Tai, Weon Pil; Yun, Yeo Bum; Kim, Song Hee [Kangwon National Univ., Chunchon (Korea, Republic of)

    1996-01-01

    The aim of this study is to investigate the change of bending strength and fatigue strength in the unpolled and poled Pb(Zr, Ti)O ferroelectrics of tetragonal, morphotropic phase boundary (MPB) and rhombohedral composition in terms of internal stress which is measured by XRD method. Before poling treatment the highest bending strength was found in rhombohedral composition. After poling treatment, the bending strength decreased in all compositions but it decreased most remarkably in tetragonal composition. The most prominent decrease of bending strength after poling treatment in tetragonal was attributed to the occurrence of microcracks due to high anisotropic internal stress around grain boundary which was induced by domain alignment toward electric field direction in the microstructure having tetragonality. The decrease of bending strength after poling in MPB and rhombohedral composition was not due to the occurrence of microcracks but to the increase in tensile internal stress perpendicular to the direction of crack propagation by domain alignment. Fatigue strength was higher before poling treatment than after poling treatment for various compositions. 13 refs., 2 tabs., 5 figs.

  9. Influence of parafunctional loading and prosthetic connection on stress distribution: a 3D finite element analysis.

    Science.gov (United States)

    Torcato, Leonardo Bueno; Pellizzer, Eduardo Piza; Verri, Fellippo Ramos; Falcón-Antenucci, Rosse Mary; Santiago Júnior, Joel Ferreira; de Faria Almeida, Daniel Augusto

    2015-11-01

    Clinicians should consider parafunctional occlusal load when planning treatment. Prosthetic connections can reduce the stress distribution on an implant-supported prosthesis. The purpose of this 3-dimensional finite element study was to assess the influence of parafunctional loading and prosthetic connections on stress distribution. Computer-aided design software was used to construct 3 models. Each model was composed of a bone and an implant (external hexagon, internal hexagon, or Morse taper) with a crown. Finite element analysis software was used to generate the finite element mesh and establish the loading and boundary conditions. A normal force (200-N axial load and 100-N oblique load) and parafunctional force (1000-N axial and 500-N oblique load) were applied. Results were visualized as the maximum principal stress. Three-way analysis of variance and Tukey test were performed, and the percentage of contribution of each variable to the stress concentration was calculated from sum-of squares-analysis. Stress was concentrated around the implant at the cortical bone, and models with the external hexagonal implant showed the highest stresses (PProsthetic Dentistry. Published by Elsevier Inc. All rights reserved.

  10. 11th International Symposium on Distributed Autonomous Robotic Systems

    CERN Document Server

    Chirikjian, Gregory

    2014-01-01

    Distributed robotics is a rapidly growing and maturing interdisciplinary research area lying at the intersection of computer science, network science, control theory, and electrical and mechanical engineering. The goal of the Symposium on Distributed Autonomous Robotic Systems (DARS) is to exchange and stimulate research ideas to realize advanced distributed robotic systems. This volume of proceedings includes 31 original contributions presented at the 2012 International Symposium on Distributed Autonomous Robotic Systems (DARS 2012) held in November 2012 at the Johns Hopkins University in Baltimore, MD USA. The selected papers in this volume are authored by leading researchers from Asia, Europa, and the Americas, thereby providing a broad coverage and perspective of the state-of-the-art technologies, algorithms, system architectures, and applications in distributed robotic systems. The book is organized into five parts, representative of critical long-term and emerging research thrusts in the multi-robot com...

  11. Rod internal pressure quantification and distribution analysis using Frapcon

    Energy Technology Data Exchange (ETDEWEB)

    Jessee, Matthew Anderson [ORNL; Wieselquist, William A [ORNL; Ivanov, Kostadin [Pennsylvania State University, University Park

    2015-09-01

    This report documents work performed supporting the Department of Energy (DOE) Office of Nuclear Energy (NE) Fuel Cycle Technologies Used Fuel Disposition Campaign (UFDC) under work breakdown structure element 1.02.08.10, ST Analysis. In particular, this report fulfills the M4 milestone M4FT- 15OR0810036, Quantify effects of power uncertainty on fuel assembly characteristics, within work package FT-15OR081003 ST Analysis-ORNL. This research was also supported by the Consortium for Advanced Simulation of Light Water Reactors (http://www.casl.gov), an Energy Innovation Hub (http://www.energy.gov/hubs) for Modeling and Simulation of Nuclear Reactors under U.S. Department of Energy Contract No. DE-AC05-00OR22725. The discharge rod internal pressure (RIP) and cladding hoop stress (CHS) distributions are quantified for Watts Bar Nuclear Unit 1 (WBN1) fuel rods by modeling core cycle design data, operation data (including modeling significant trips and downpowers), and as-built fuel enrichments and densities of each fuel rod in FRAPCON-3.5. A methodology is developed which tracks inter-cycle assembly movements and assembly batch fabrication information to build individual FRAPCON inputs for each evaluated WBN1 fuel rod. An alternate model for the amount of helium released from the zirconium diboride (ZrB2) integral fuel burnable absorber (IFBA) layer is derived and applied to FRAPCON output data to quantify the RIP and CHS for these types of fuel rods. SCALE/Polaris is used to quantify fuel rodspecific spectral quantities and the amount of gaseous fission products produced in the fuel for use in FRAPCON inputs. Fuel rods with ZrB2 IFBA layers (i.e., IFBA rods) are determined to have RIP predictions that are elevated when compared to fuel rod without IFBA layers (i.e., standard rods) despite the fact that IFBA rods often have reduced fill pressures and annular fuel pellets. The primary contributor to elevated RIP predictions at burnups less than and greater than 30 GWd

  12. 9th International conference on distributed computing and artificial intelligence

    CERN Document Server

    Santana, Juan; González, Sara; Molina, Jose; Bernardos, Ana; Rodríguez, Juan; DCAI 2012; International Symposium on Distributed Computing and Artificial Intelligence 2012

    2012-01-01

    The International Symposium on Distributed Computing and Artificial Intelligence 2012 (DCAI 2012) is a stimulating and productive forum where the scientific community can work towards future cooperation in Distributed Computing and Artificial Intelligence areas. This conference is a forum in which  applications of innovative techniques for solving complex problems will be presented. Artificial intelligence is changing our society. Its application in distributed environments, such as the internet, electronic commerce, environment monitoring, mobile communications, wireless devices, distributed computing, to mention only a few, is continuously increasing, becoming an element of high added value with social and economic potential, in industry, quality of life, and research. These technologies are changing constantly as a result of the large research and technical effort being undertaken in both universities and businesses. The exchange of ideas between scientists and technicians from both the academic and indus...

  13. Distributed computing and artificial intelligence : 10th International Conference

    CERN Document Server

    Neves, José; Rodriguez, Juan; Santana, Juan; Gonzalez, Sara

    2013-01-01

    The International Symposium on Distributed Computing and Artificial Intelligence 2013 (DCAI 2013) is a forum in which applications of innovative techniques for solving complex problems are presented. Artificial intelligence is changing our society. Its application in distributed environments, such as the internet, electronic commerce, environment monitoring, mobile communications, wireless devices, distributed computing, to mention only a few, is continuously increasing, becoming an element of high added value with social and economic potential, in industry, quality of life, and research. This conference is a stimulating and productive forum where the scientific community can work towards future cooperation in Distributed Computing and Artificial Intelligence areas. These technologies are changing constantly as a result of the large research and technical effort being undertaken in both universities and businesses. The exchange of ideas between scientists and technicians from both the academic and industry se...

  14. Influence of Hardening Model on Weld Residual Stress Distribution

    Energy Technology Data Exchange (ETDEWEB)

    Mullins, Jonathan; Gunnars, Jens (Inspecta Technology AB, Stockholm (Sweden))

    2009-06-15

    This study is the third stage of a project sponsored by the Swedish Radiation Safety Authority (SSM) to improve the weld residual stress modelling procedures currently used in Sweden. The aim of this study was to determine which material hardening model gave the best agreement with experimentally measured weld residual stress distributions. Two girth weld geometries were considered: 19mm and 65mm thick girth welds with Rin/t ratios of 10.5 and 2.8, respectively. The FE solver ABAQUS Standard v6.5 was used for analysis. As a preliminary step some improvements were made to the welding simulation procedure used in part one of the project. First, monotonic stress strain curves and a mixed isotropic/kinematic hardening model were sourced from the literature for 316 stainless steel. Second, more detailed information was obtained regarding the geometry and welding sequence for the Case 1 weld (compared with phase 1 of this project). Following the preliminary step, welding simulations were conducted using isotropic, kinematic and mixed hardening models. The isotropic hardening model gave the best overall agreement with experimental measurements; it is therefore recommended for future use in welding simulations. The mixed hardening model gave good agreement for predictions of the hoop stress but tended to under estimate the magnitude of the axial stress. It must be noted that two different sources of data were used for the isotropic and mixed models in this study and this may have contributed to the discrepancy in predictions. When defining a mixed hardening model it is difficult to delineate the relative contributions of isotropic and kinematic hardening and for the model used it may be that a greater isotropic hardening component should have been specified. The kinematic hardening model consistently underestimated the magnitude of both the axial and hoop stress and is not recommended for use. Two sensitivity studies were also conducted. In the first the effect of using a

  15. Influence of Hardening Model on Weld Residual Stress Distribution

    International Nuclear Information System (INIS)

    Mullins, Jonathan; Gunnars, Jens

    2009-06-01

    This study is the third stage of a project sponsored by the Swedish Radiation Safety Authority (SSM) to improve the weld residual stress modelling procedures currently used in Sweden. The aim of this study was to determine which material hardening model gave the best agreement with experimentally measured weld residual stress distributions. Two girth weld geometries were considered: 19mm and 65mm thick girth welds with Rin/t ratios of 10.5 and 2.8, respectively. The FE solver ABAQUS Standard v6.5 was used for analysis. As a preliminary step some improvements were made to the welding simulation procedure used in part one of the project. First, monotonic stress strain curves and a mixed isotropic/kinematic hardening model were sourced from the literature for 316 stainless steel. Second, more detailed information was obtained regarding the geometry and welding sequence for the Case 1 weld (compared with phase 1 of this project). Following the preliminary step, welding simulations were conducted using isotropic, kinematic and mixed hardening models. The isotropic hardening model gave the best overall agreement with experimental measurements; it is therefore recommended for future use in welding simulations. The mixed hardening model gave good agreement for predictions of the hoop stress but tended to under estimate the magnitude of the axial stress. It must be noted that two different sources of data were used for the isotropic and mixed models in this study and this may have contributed to the discrepancy in predictions. When defining a mixed hardening model it is difficult to delineate the relative contributions of isotropic and kinematic hardening and for the model used it may be that a greater isotropic hardening component should have been specified. The kinematic hardening model consistently underestimated the magnitude of both the axial and hoop stress and is not recommended for use. Two sensitivity studies were also conducted. In the first the effect of using a

  16. Mapping residual and internal stress in materials by neutron diffraction

    International Nuclear Information System (INIS)

    Withers, Ph.J.

    2007-01-01

    Neutron diffraction provides one of the few means of mapping residual stresses deep within the bulk of materials and components. This article reviews the basic scientific methodology by which internal strains and stresses are inferred from recorded diffraction peaks. Both conventional angular scans and time-of-flight measurements are reviewed and compared. Their complementarity with analogous synchrotron X-ray methods is also highlighted. For measurements to be exploited in structural integrity calculations underpinning the safe operation of engineering components, measurement standards have been defined and the major findings are summarised. Examples are used to highlight the unique capabilities of the method showing how it can provide insights ranging from the basic physics of slip mechanisms in hexagonal polycrystalline materials, through the materials optimisation of stress induced transformations in smart nano-materials, to the industrial introduction of novel friction welding processes exploiting stress residual measurements transferred from prototype sub-scale tests to the joining of full-scale aero-engine assemblies. (author)

  17. Distributed Computing and Artificial Intelligence, 12th International Conference

    CERN Document Server

    Malluhi, Qutaibah; Gonzalez, Sara; Bocewicz, Grzegorz; Bucciarelli, Edgardo; Giulioni, Gianfranco; Iqba, Farkhund

    2015-01-01

    The 12th International Symposium on Distributed Computing and Artificial Intelligence 2015 (DCAI 2015) is a forum to present applications of innovative techniques for studying and solving complex problems. The exchange of ideas between scientists and technicians from both the academic and industrial sector is essential to facilitate the development of systems that can meet the ever-increasing demands of today’s society. The present edition brings together past experience, current work and promising future trends associated with distributed computing, artificial intelligence and their application in order to provide efficient solutions to real problems. This symposium is organized by the Osaka Institute of Technology, Qatar University and the University of Salamanca.

  18. Grain boundary cavity growth under applied stress and internal pressure

    International Nuclear Information System (INIS)

    Mancuso, J.F.

    1977-08-01

    The growth of grain boundary cavities under applied stress and internal gas pressure was investigated. Methane gas filled cavities were produced by the C + 4H reversible CH4 reaction in the grain boundaries of type 270 nickel by hydrogen charging in an autoclave at 500 0 C with a hydrogen pressure of either 3.4 or 14.5 MPa. Intergranular fracture of nickel was achieved at a charging temperature of 300 0 C and 10.3 MPa hydrogen pressure. Cavities on the grain boundaries were observed in the scanning electron microscope after fracture. Photomicrographs of the cavities were produced in stereo pairs which were analyzed so as to correct for perspective distortion and also to determine the orientational dependence of cavity growth under an applied tensile stress

  19. Analysis of neutron diffraction peak broadening caused by internal stresses in composite materials

    International Nuclear Information System (INIS)

    Todd, R.I.; Borsa, C.; Derby, B.

    1994-01-01

    Neutron diffraction is an essential tool in the study of internal stresses in composite materials. In most work only the peak shifts caused by the related elastic strains are considered, but other valuable information exists in the form of peak shape changes. The conditions under which the pure diffraction profile of the composite (i.e. the profile when all sources of broadening not caused by the residual stresses are removed) represents the probability distribution of the peak shifts corresponding to the strains are examined. It is shown that in these conditions, the pure diffraction profile has no attributes of particle size broadening (and vice versa), thereby providing a test for the validity of results interpreted in this way. The experimental derivation of measured strain distributions in Al 2 O 3 /SiCp composites using neutron diffraction is described. No apparent particle size broadening was detected, demonstrating the validity of the results, which also satisfied other tests for consistency

  20. Stress distribution characteristics in the vicinity of coal seam floor

    Science.gov (United States)

    Cui, Zimo; Chanda, Emmanuel; Zhao, Jingli; Wang, Zhihe

    2018-01-01

    Although longwall top-coal caving (LTCC) has been a popular, more productive and cost-effective method in recent years, roadway floor heave and rock bursts frequently appear when exploiting such coal seams with large dip angle. This paper proposes addressing this problem by adopting three-dimensional roadway layout of stagger arrangement (3-D RLSA). In this study, the first step was to analyse the stress distribution characteristics in the vicinity of coal seam floor based on the stress slip line field theory. In the second step, numerical calculation using FLAC3D was conducted. Finally, an evaluation of the 3-D RLSA for solving this particular issue was given. Results indicate that for this particular mine the proposed 3-D RLSA results in 24% increase in the coal recovery ratio and a modest reduction in excavation and maintenance costs compared to the conventional LTCC method.

  1. Analysis of the temperature and stress distributions in ceramic window materials subjected to microwave heating

    International Nuclear Information System (INIS)

    Ferber, M.K.; Kimrey, H.D.; Becher, P.F.

    1983-07-01

    The temperature and stress and distributions generated in ceramic materials currently employed in microwave gyrotron tube windows were determined for a variety of operating conditions. Both edge- and face-cooled windows of either polycrystalline BeO or polycrystalline Al 2 O 3 were considered. The actual analysis involved three steps. First, a computer program was used to determine the electric field distribution within the window at a given power level and frequency (TE 02 wave propagation assumed). This program was capable of describing both the radial and axial dependence of the electric field. The effects of multiple internal reflections at the various dielectric interfaces were also accounted for. Secondly, the field distribution was used to derive an expression for the heat generated per unit volume per unit time within the window due to dieletric losses. A generalized heat conduction computer code was then used to compute the temperature distribution based on the heat generation function. Third, the stresses were determined from the temperature profiles using analytical expression or a finite-element computer program. Steady-state temperature and stress profiles were computed for the face-cooled and edge-cooled windows

  2. Distribution of internal mammary lymphadenopathy in breast carcinoma: CT appraisal

    International Nuclear Information System (INIS)

    Scatarige, J.C.; Fishman, E.K.; Zinreich, E.S.; Almaraz, R.

    1987-01-01

    The authors studied the anatomic distribution of enlarged internal mammary lymph nodes in breast carcinoma by reviewing thoracic CT examinations in 219 women with operable, advanced or recurrent disease. Enlarged internal mammary lymph nodes were observed in 45 patients (20.5%); they were unilateral in 32 and bilateral in 13. Lymphadenopathy was limited to one anterior intercostal space in 43%, two spaces in 26%, and three or more species in 31%. Dominant modal disease was centered at the first anterior intercostal space in 14%, the second space in 60%, and the third space in 26%. Isolated adenopathy in the fourth intercostal space was not observed. The authors' data concur with current surgical practice when internal mammary lymph nodes are sampled. Implications for preoperative imaging strategy are discussed

  3. Electron-beam-charged dielectrics: Internal charge distribution

    Science.gov (United States)

    Beers, B. L.; Pine, V. W.

    1981-01-01

    Theoretical calculations of an electron transport model of the charging of dielectrics due to electron bombardment are compared to measurements of internal charge distributions. The emphasis is on the distribution of Teflon. The position of the charge centroid as a function of time is not monotonic. It first moves deeper into the material and then moves back near to the surface. In most time regimes of interest, the charge distribution is not unimodal, but instead has two peaks. The location of the centroid near saturation is a function of the incident current density. While the qualitative comparison of theory and experiment are reasonable, quantitative comparison shows discrepancies of as much as a factor of two.

  4. The Future of Electricity Distribution Regulation. Lessons from International Experience

    Energy Technology Data Exchange (ETDEWEB)

    Nillesen, P.H.L.

    2008-12-03

    This thesis contains five essays on the regulation of electricity distribution networks, each presenting a different point of view. Two essays use US data to demonstrate that incentive-based regulation has valuable application within a management setting and can lead to gaming behaviour within a regulatory setting. One essay discusses the lessons that can be drawn from the failed first electricity distribution price control review in the Netherlands. One essay presents the views of 75 international regulation managers and gives recommendations on ways to improve the regulatory quality and process. The final essay analyses the economic consequences of the forced ownership unbundling of the electricity distribution networks in 1998 in New Zealand, and draws lessons for future structural remedies that may be sought in other countries.

  5. The Future of Electricity Distribution Regulation. Lessons from International Experience

    International Nuclear Information System (INIS)

    Nillesen, P.H.L.

    2008-01-01

    This thesis contains five essays on the regulation of electricity distribution networks, each presenting a different point of view. Two essays use US data to demonstrate that incentive-based regulation has valuable application within a management setting and can lead to gaming behaviour within a regulatory setting. One essay discusses the lessons that can be drawn from the failed first electricity distribution price control review in the Netherlands. One essay presents the views of 75 international regulation managers and gives recommendations on ways to improve the regulatory quality and process. The final essay analyses the economic consequences of the forced ownership unbundling of the electricity distribution networks in 1998 in New Zealand, and draws lessons for future structural remedies that may be sought in other countries

  6. Influence of Cement Particle-Size Distribution on Early Age Autogenous Strains and Stresses in Cement-Based Materials

    DEFF Research Database (Denmark)

    Bentz, Dale P.; Jensen, Ole Mejlhede; Hansen, Kurt Kielsgaard

    2001-01-01

    The influence of cement particle-size distribution on autogenous strains and stresses in cement pastes of identical water-to-cement ratios is examined for cement powders of four different finenesses. Experimental measurements include chemical shrinkage, to quantify degree of hydration; internal r...

  7. Internal stress model for pre-primary stage of low-stress creep

    International Nuclear Information System (INIS)

    Kloc, L

    2010-01-01

    Initial transient stage in low-stress creep experiments was observed in all such experiments. Recently, evidences were presented that this stage cannot be considered as a normal creep primary stage, though the shape of the creep curve is similar. The strain reached during this so called pre-primary stage is fully recoverable upon unloading; the internal stresses must play important role in the effect. Model of standard linear anelastic solid was modified by introduction of creeping body instead of viscous dashpot. Both power law and hyperbolic sine creep law were used to fit observed creep curves of model and structural materials. Mainly the model using hyeprbolic sine creep law provides good fit to individual creep curves and sets of creep curves at different stresses.

  8. Numerical modeling of regional stress distributions for geothermal exploration

    Science.gov (United States)

    Guillon, Theophile; Peter-Borie, Mariane; Gentier, Sylvie; Blaisonneau, Arnold

    2017-04-01

    Any high-enthalpy unconventional geothermal projectcan be jeopardized by the uncertainty on the presence of the geothermal resource at depth. Indeed, for the majority of such projects the geothermal resource is deeply seated and, with the drilling costs increasing accordingly, must be located as precisely as possible to increase the chance of their economic viability. In order to reduce the "geological risk", i.e., the chance to poorly locate the geothermal resource, a maximum amount of information must be gathered prior to any drilling of exploration and/or operational well. Cross-interpretation from multiple disciplines (e.g., geophysics, hydrology, geomechanics …) should improve locating the geothermal resource and so the position of exploration wells ; this is the objective of the European project IMAGE (grant agreement No. 608553), under which the work presented here was carried out. As far as geomechanics is concerned, in situ stresses can have a great impact on the presence of a geothermal resource since they condition both the regime within the rock mass, and the state of the major fault zones (and hence, the possible flow paths). In this work, we propose a geomechanical model to assess the stress distribution at the regional scale (characteristic length of 100 kilometers). Since they have a substantial impact on the stress distributions and on the possible creation of regional flow paths, the major fault zones are explicitly taken into account. The Distinct Element Method is used, where the medium is modeled as fully deformable blocks representing the rock mass interacting through mechanically active joints depicting the fault zones. The first step of the study is to build the model geometry based on geological and geophysical evidences. Geophysical and structural geology results help positioning the major fault zones in the first place. Then, outcrop observations, structural models and site-specific geological knowledge give information on the fault

  9. Marital Processes, Neuroticism, and Stress as Risk Factors for Internalizing Symptoms.

    Science.gov (United States)

    Brock, Rebecca L; Lawrence, Erika

    2014-03-01

    Marital discord has a robust association with depression, yet it is rarely considered within broader etiological frameworks of psychopathology. Further, little is known about the particular aspects of relationships that have the greatest impact on psychopathology. The purpose of the present study was to test a novel conceptual framework including neuroticism, specific relationship processes (conflict management, partner support, emotional intimacy, and distribution of power and control), and stress as predictors of internalizing symptoms (depression and anxiety). Questionnaire and interview data were collected from 103 husbands and wives 5 times over the first 7 years of marriage. Results suggest that neuroticism (an expression of the underlying vulnerability for internalizing disorders) contributes to symptoms primarily through high levels of non-marital stress, an imbalance of power/control in one's marriage, and poor partner support for husbands, and through greater emotional disengagement for wives. Marital processes, neuroticism, and stress work together to significantly predict internalizing symptoms, demonstrating the need to routinely consider dyadic processes in etiological models of individual psychopathology. Specific recommendations for adapting and implementing couple interventions to prevent and treat individual psychopathology are discussed.

  10. The internal stress measurement the neutron diffraction bring happiness to your country

    Energy Technology Data Exchange (ETDEWEB)

    Minakawa, Nobuaki [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    2003-03-01

    The neutron was discovered by Chadwick in 1932. The first reactor was constructed by the USA in 1942. After that, the research and development of reactors advanced. Numbers of reactors were constructed in Europe and in the US. The researches, which use the neutron, were performed actively and excellent results were obtained in wide fields. The penetrating power of the neutron and the neutron diffraction method began to attract attention for the application to the internal stress measurement, too. In Japan, the neutron diffractometer for the residual stress measurement exclusive was installed in the JRR-3M research reactor of JAERI in 1992, and the research was started. At present, we are using it for the stress measurements of the parts of aircrafts, railways, automobiles, buildings, machines, home electronics products and so on including nuclear reactors. Reliable science must be introduced in order to support safety and long life operation and to supply them at reasonable cost. Among the various scientific probes to find faults in materials, diffraction technique is used to measure the strain distribution in materials by observing the local changes of the distance between crystallographic planes and the stress distribution is computed to improve manufacturing processes. It is only neutron diffraction that can be used to measure the strain inside the materials. Here, I present an overview of the utilization of neutron scattering research for the industrial uses and the history of the neutron scattering research in JAERI briefly. (J.P.N.)

  11. The internal stress measurement the neutron diffraction will bring happiness to your country

    International Nuclear Information System (INIS)

    Minakawa, Nobuaki

    2003-01-01

    The neutron was discovered by Chadwick in 1932. The first reactor was constructed by the USA in 1942. After that, the research and development of reactors advanced. Numbers of reactors were constructed in Europe and in the US. The researches, which use the neutron, were performed actively and excellent results were obtained in wide fields. The penetrating power of the neutron and the neutron diffraction method began to attract attention for the application to the internal stress measurement, too. In Japan, the neutron diffractometer for the residual stress measurement exclusive was installed in the JRR-3M research reactor of JAERI in 1992, and the research was started. At present, we are using it for the stress measurements of the parts of air crafts, railways, automobiles, buildings, machines, home electronics products and so on including nuclear reactors. Reliable science must be introduced in order to support safety and long life operation and to supply them at reasonable cost. Among the various scientific probes to find faults in materials, diffraction technique is used to measure the strain distribution in materials by observing the local changes of the distance between crystallographic planes and the stress distribution is computed to improve manufacturing processes. It is only neutron diffraction that can be used to measure the strain inside the materials. Here, I present an overview of the utilization of neutron scattering research for the industrial uses and the history of the neutron scattering research in JAERI briefly. (J.P.N.)

  12. 13th International Conference on Distributed Computing and Artificial Intelligence

    CERN Document Server

    Silvestri, Marcello; González, Sara

    2016-01-01

    The special session Decision Economics (DECON) 2016 is a scientific forum by which to share ideas, projects, researches results, models and experiences associated with the complexity of behavioral decision processes aiming at explaining socio-economic phenomena. DECON 2016 held in the University of Seville, Spain, as part of the 13th International Conference on Distributed Computing and Artificial Intelligence (DCAI) 2016. In the tradition of Herbert A. Simon’s interdisciplinary legacy, this book dedicates itself to the interdisciplinary study of decision-making in the recognition that relevant decision-making takes place in a range of critical subject areas and research fields, including economics, finance, information systems, small and international business, management, operations, and production. Decision-making issues are of crucial importance in economics. Not surprisingly, the study of decision-making has received a growing empirical research efforts in the applied economic literature over the last ...

  13. Association between Independent Reports of Maternal Parenting Stress and Children's Internalizing Symptomatology

    Science.gov (United States)

    Rodriguez, Christina M.

    2011-01-01

    Although considerable research has investigated parenting stress and children's externalizing behavior problems, comparatively less has considered parenting stress in relation to children's internalizing difficulties. Even less research on parenting stress has incorporated children's report of their internalizing symptoms or the potential…

  14. Wind Power Forecasting Error Distributions: An International Comparison

    DEFF Research Database (Denmark)

    Hodge, Bri-Mathias; Lew, Debra; Milligan, Michael

    2012-01-01

    Wind power forecasting is essential for greater penetration of wind power into electricity systems. Because no wind forecasting system is perfect, a thorough understanding of the errors that may occur is a critical factor for system operation functions, such as the setting of operating reserve...... levels. This paper provides an international comparison of the distribution of wind power forecasting errors from operational systems, based on real forecast data. The paper concludes with an assessment of similarities and differences between the errors observed in different locations....

  15. 11th International Conference on Distributed Computing and Artificial Intelligence

    CERN Document Server

    Bersini, Hugues; Corchado, Juan; Rodríguez, Sara; Pawlewski, Paweł; Bucciarelli, Edgardo

    2014-01-01

    The 11th International Symposium on Distributed Computing and Artificial Intelligence 2014 (DCAI 2014) is a forum to present applications of innovative techniques for studying and solving complex problems. The exchange of ideas between scientists and technicians from both the academic and industrial sector is essential to facilitate the development of systems that can meet the ever-increasing demands of today’s society. The present edition brings together past experience, current work and promising future trends associated with distributed computing, artificial intelligence and their application in order to provide efficient solutions to real problems. This year’s technical program presents both high quality and diversity, with contributions in well-established and evolving areas of research (Algeria, Brazil, China, Croatia, Czech Republic, Denmark, France, Germany, Ireland, Italy, Japan, Malaysia, Mexico, Poland, Portugal, Republic of Korea, Spain, Taiwan, Tunisia, Ukraine, United Kingdom), representing ...

  16. The Influence of Distributed Leadership on Job Stress in Technical and Vocational Education

    OpenAIRE

    Siva Rabindarang; Khuan Wai Bing; Khoo Yin Yin

    2014-01-01

    Distributed leadership proposed in the field of leadership studies for the improvement of organizational effectiveness. Job stress is the work situation that can affect the organizational performance. Thus, these studies carried out to measure the influence of distributed leadership on job stress. Studies on distributed leadership and job stress are scarce especially in technical and vocational education. Therefore, the purpose of this study is to determine the influence of distributed leader...

  17. Primitive Path Analysis and Stress Distribution in Highly Strained Macromolecules.

    Science.gov (United States)

    Hsu, Hsiao-Ping; Kremer, Kurt

    2018-01-16

    Polymer material properties are strongly affected by entanglement effects. For long polymer chains and composite materials, they are expected to be at the origin of many technically important phenomena, such as shear thinning or the Mullins effect, which microscopically can be related to topological constraints between chains. Starting from fully equilibrated highly entangled polymer melts, we investigate the effect of isochoric elongation on the entanglement structure and force distribution of such systems. Theoretically, the related viscoelastic response usually is discussed in terms of the tube model. We relate stress relaxation in the linear and nonlinear viscoelastic regimes to a primitive path analysis (PPA) and show that tension forces both along the original paths and along primitive paths, that is, the backbone of the tube, in the stretching direction correspond to each other. Unlike homogeneous relaxation along the chain contour, the PPA reveals a so far not observed long-lived clustering of topological constraints along the chains in the deformed state.

  18. The Relationships among Perfectionism, Acculturation, and Stress in Asian International Students

    Science.gov (United States)

    Nilsson, Johanna E.; Butler, Jenay; Shouse, Sarah; Joshi, Chetan

    2008-01-01

    This study examined relationships among perfectionism, acculturation, and stress in 76 Asian international students. Results showed that perfectionism and acculturation predicted stress, together accounting for 50% of the variance in stress. Furthermore, acculturation explained students' experience of stress above and beyond perfectionism, and 1…

  19. The stress distribution in shell bodies and wings as an equilibrium problem

    Science.gov (United States)

    Wagner, H

    1937-01-01

    This report treats the stress distribution in shell-shaped airplane components (fuselage, wings) as an equilibrium problem; it includes both cylindrical and non-cylindrical shells. In particular, it treats the stress distribution at the point of stress application and at cut-out points.

  20. Grading Practices and Distributions Across Internal Medicine Clerkships.

    Science.gov (United States)

    Fazio, Sara B; Torre, Dario M; DeFer, Thomas M

    2016-01-01

    Clerkship evaluation and grading practices vary widely between U.S. medical schools. Grade inflation continues to exist, and grade distribution is likely to be different among U.S. medical schools. Increasing the number of available grades curtails "grade inflation." A national survey of all Clerkship Directors in Internal Medicine members was administered in 2011. The authors assessed key aspects of grading. Response rate was 76%. Among clerkship directors (CDs), 61% of respondents agreed that grade inflation existed in the internal medicine clerkship at their school, and 43% believed that it helped students obtain better residency positions. With respect to grading practices, 79% of CDs define specific behaviors needed to achieve each grade, and 36% specify an ideal grade distribution. In addition, 44% have a trained core faculty responsible for evaluating students, 35% describe formal grading meetings, and 39% use the Reporter-Interpreter-Manager-Educator (RIME) scheme. Grading scales were described as follows: 4% utilize a pass/fail system, 13% a 3-tier (e.g., Honors/Pass/Fail), 45% 4-tier, 35% 5-tier, and 4% 6+-tier system. There was a trend to higher grades with more tiers available. Grade inflation continues in the internal medicine clerkship. Almost half of CDs feel that this practice assists students to obtain better residency positions. A minority of programs have a trained core faculty who are responsible for evaluation. About one third have formal grading meetings and use the RIME system; both have been associated with more robust and balanced grading practices. In particular, there is a wide variation between schools in the percentage of students who are awarded the highest grade, which has implications for residency applications. Downstream users of clinical clerkship grades must be fully aware of these variations in grading in order to appropriately judge medical student performance.

  1. Formation and distribution of international tourism flows in geographical space

    Directory of Open Access Journals (Sweden)

    Oleksandr Korol

    2017-10-01

    Full Text Available Properties of geographical space that are of key importance for international tourism, as length and discreteness, are analyzed in the article. Length makes tourists cover distances, whereas discreteness manifests itself in spatial heterogeneity. Tourism in conditions of homogeneous space is vain. That is, heterogeneity brings sense to travels as well as determines their direction. So, the effect of geographical space’s length and spatial heterogeneity on formation and distribution of tourism flows is assessed, international tourism’s geographical essence is disclosed also. Apperception of geographical space in usual environment and its effect on tourist’s original motives are described. Following the bases of behaviorism, the tourism original motives, in particular those for migration, comfort, contrast and aesthetics are substantiated. The motive for migration is a kind of “pushing” tourists outside their usual environment. To stop all fears that may cause anxiety in destination, the latter should guarantee satisfaction of those human needs which A. Maslow refers to as basic needs. The necessity to satisfy these needs forms in tourists the motive for comfort. Closely located destinations in neighboring countries can be of little difference form usual environment. Driven by the motive for contrast, tourists aspire to visit places that totally differ from their usual environment, and contrast (are exotic to it. Thus, the motive for contrast seemingly “pulls” the tourists up to certain (exotic destinations. Finally, following the considered spatial specificities of land surface and tourist-driving original motives, a conceptual model of formation and distribution of international tourism flows in geographical space is developed.

  2. Stress Distribution during Rapid Canine Retraction with a Distraction Device: A Finite Element Study

    Directory of Open Access Journals (Sweden)

    Nareen Chakravarthy Challagulla

    2013-01-01

    Conclusion: The periodontium in the maxillary first molar region showed the maximum stress and the canine showed unequal stress distribution with more stress at the crest of the alveolar bone and lesser stress at the apical region which lessens root resorption.

  3. Studies of internal stress in diamond films prepared by DC plasma chemical vapour deposition

    International Nuclear Information System (INIS)

    Wang Wanlu; Gao Jinying; Liao Kejun; Liu Anmin

    1992-01-01

    The internal stress in diamond thin films deposited by DC plasma CVD was studied as a function of methane concentration and deposited temperature. Experimental results have shown that total stress in diamond thin films is sensitive to the deposition conditions. The results also indicate that the compressive stress can be explained in terms of amorphous state carbon and hydrogen, and tensile stress is ascribed to the grain boundary relaxation model due to high internal surface area and microstructure with voids

  4. Tibiofemoral contact stress and stress distribution evaluation of total knee arthroplasties.

    Science.gov (United States)

    Szivek, J A; Cutignola, L; Volz, R G

    1995-08-01

    The Fuji film (Itochu, Los Angeles, CA) area analysis technique demonstrates that a more accurate assessment of tibiofemoral contact stresses is possible when the film is used at 37 degrees C and at the upper end of its sensitivity range (in this case, a 2,000-N load). An AMK with a regular and Hylamer-M insert (DePuy, Warsaw, IN), an MG II (Zimmer, Warsaw, IN), an Omnifit (Osteonics, Allendale, NJ), an Ortholoc III (Dow Corning Wright, Midland, MI), a PCA II (Howmedica, Rutherford, NJ), and a PFC (Johnson & Johnson Orthopaedics, Raynham, MA) had average contact stresses that varied only 12% at 60 degrees flexion. At 0 degrees, 15 degrees and 60 degrees flexion, stresses ranged from 13 to 25 MPa. Contact area distribution ratios, which were smaller at 37 degrees C than at 24 degrees C, provide a quantitative means of grouping implants according to the shape of the tibiofemoral contact area. The Omnifit, MG II, PCA II, and PFC had small ratios (symmetric areas). The AMK and Ortholoc III had large ratios (asymmetric contact areas). If the impression is reflective of wear, it would be expected to be focal in knees with small ratios and contact areas, and uniform in knees with large ratios and contact areas, whereas large ratios and small areas would imply a linear wear pattern. Calibrated electrical resistance contact stress measurements indicated that the Fuji film measurements underestimated the magnitude of contact stresses. They also provided a means of quantifying the rate of area increase during initial loading of the knees, with the highest area increase noted for the knee with the roughest insert (Ortholoc III) and the lowest area increase for the knee with the smoothest insert (PCA II).

  5. Investigation of stress distribution in normal and oblique partial penetration. Welded nozzles by 3-D photoelastic stress freezing method

    International Nuclear Information System (INIS)

    Miyamoto, H.; Kubo, M.; Katori, T.

    1981-01-01

    Experimental investigation by 3-D photoelasticity has been carried out to measure the stress distribution of partial penetration welded nozzles attached to the bottom head of a pressure vessel. A 3-D photoelastic stress freezing method was chosen as the most effective means of observation of the stress distribution in the vicinity of the nozzle/wall weld. The experimental model was a 1:20 scale spherical bottom head. Both an axisymmetric nozzle and an asymmetric nozzle were investigated. Epoxy resin, which is a thermosetting plastic, was used as the model material. The oblique effect was examined by comparing the stress distribution of the asymmetric nozzle with that of the axisymmetric nozzle. Furthermore, the experimental results were compared with the analytical results using 3-D finite element method (FEM). The stress distributions obtained from the frozen fringe pattern of the 3-D photoelastic model were in good agreement with those by 3-D FEM. (orig.)

  6. Estimation of stress distribution in ferromagnetic tensile specimens using low cost eddy current stress measurement system and BP neural network.

    Directory of Open Access Journals (Sweden)

    Jianwei Li

    Full Text Available Estimation of the stress distribution in ferromagnetic components is very important for evaluating the working status of mechanical equipment and implementing preventive maintenance. Eddy current testing technology is a promising method in this field because of its advantages of safety, no need of coupling agent, etc. In order to reduce the cost of eddy current stress measurement system, and obtain the stress distribution in ferromagnetic materials without scanning, a low cost eddy current stress measurement system based on Archimedes spiral planar coil was established, and a method based on BP neural network to obtain the stress distribution using the stress of several discrete test points was proposed. To verify the performance of the developed test system and the validity of the proposed method, experiment was implemented using structural steel (Q235 specimens. Standard curves of sensors at each test point were achieved, the calibrated data were used to establish the BP neural network model for approximating the stress variation on the specimen surface, and the stress distribution curve of the specimen was obtained by interpolating with the established model. The results show that there is a good linear relationship between the change of signal modulus and the stress in most elastic range of the specimen, and the established system can detect the change in stress with a theoretical average sensitivity of -0.4228 mV/MPa. The obtained stress distribution curve is well consonant with the theoretical analysis result. At last, possible causes and improving methods of problems appeared in the results were discussed. This research has important significance for reducing the cost of eddy current stress measurement system, and advancing the engineering application of eddy current stress testing.

  7. Estimation of stress distribution in ferromagnetic tensile specimens using low cost eddy current stress measurement system and BP neural network.

    Science.gov (United States)

    Li, Jianwei; Zhang, Weimin; Zeng, Weiqin; Chen, Guolong; Qiu, Zhongchao; Cao, Xinyuan; Gao, Xuanyi

    2017-01-01

    Estimation of the stress distribution in ferromagnetic components is very important for evaluating the working status of mechanical equipment and implementing preventive maintenance. Eddy current testing technology is a promising method in this field because of its advantages of safety, no need of coupling agent, etc. In order to reduce the cost of eddy current stress measurement system, and obtain the stress distribution in ferromagnetic materials without scanning, a low cost eddy current stress measurement system based on Archimedes spiral planar coil was established, and a method based on BP neural network to obtain the stress distribution using the stress of several discrete test points was proposed. To verify the performance of the developed test system and the validity of the proposed method, experiment was implemented using structural steel (Q235) specimens. Standard curves of sensors at each test point were achieved, the calibrated data were used to establish the BP neural network model for approximating the stress variation on the specimen surface, and the stress distribution curve of the specimen was obtained by interpolating with the established model. The results show that there is a good linear relationship between the change of signal modulus and the stress in most elastic range of the specimen, and the established system can detect the change in stress with a theoretical average sensitivity of -0.4228 mV/MPa. The obtained stress distribution curve is well consonant with the theoretical analysis result. At last, possible causes and improving methods of problems appeared in the results were discussed. This research has important significance for reducing the cost of eddy current stress measurement system, and advancing the engineering application of eddy current stress testing.

  8. Photoelastic investigation of the stresses in a stepped cylinder under internal pressure

    International Nuclear Information System (INIS)

    Sawa, Yoshiaki; Nishida, Masataka

    1985-01-01

    The states of stress distribution of the stepped cylinder under inner-pressure are studied by means of stress freezing photoelastic method. The experimental results reveal that fiber stress concentration occurs on the circular arc and hoop stress concentration occurs at the jointing point of the straight line and the arc and that each maximum value of fiver stress and hoop stress depends very greatly on the diameter of a small cylinder and the radius of curvature. And the relationship between the stress concentration factors and these shape factors are given. Effects of wall thickness on the stress concentration factors are also determined. (author)

  9. Spatial distribution of absorbed dose onboard of International Space Station

    International Nuclear Information System (INIS)

    Jadrnickova, I.; Spumy, F.; Tateyama, R.; Yasuda, N.; Kawashima, H.; Kurano, M.; Uchihori, Y.; Kitamura, H.; Akatov, Yu.; Shurshakov, V.; Kobayashi, I.; Ohguchi, H.; Koguchi, Y.

    2009-01-01

    The passive detectors (LD and PNTD) were exposed onboard of Russian Service Module Qn the International Space Station (ISS) from August 2004 to October 2005 (425 days). The detectors were located at 6 different positions inside the Service Module and also in 32 pockets on the surface of the spherical tissue-equivalent phantom located in crew cabin. Distribution of absorbed doses and dose equivalents measured with passive detectors, as well as LET spectra of fluences of registered particles, are presented as the function of detectors' location. The variation of dose characteristics for different locations can be up to factor of 2. In some cases, data measured with passive detectors are also compared with the data obtained by means of active instruments. (authors)

  10. Laser quench hardening of steel: Effects of superimposed elastic pre-stress on the hardness and residual stress distribution

    Science.gov (United States)

    Meserve, Justin

    Cold drawn AISI 4140 beams were LASER surface hardened with a 2 kW CO2 LASER. Specimens were treated in the free state and while restrained in a bending fixture inducing surface tensile stresses of 94 and 230 MPa. Knoop hardness indentation was used to evaluate the through thickness hardness distribution, and a layer removal methodology was used to evaluate the residual stress distribution. Results showed the maximum surface hardness attained was not affected by pre-stress during hardening, and ranged from 513 to 676 kg/mm2. The depth of effective hardening varied at different magnitudes of pre-stress, but did not vary proportionately to the pre-stress. The surface residual stress, coinciding with the maximum compressive residual stress, increased as pre-stress was increased, from 1040 MPa for the nominally treated specimens to 1270 MPa for specimens pre-stressed to 230 MPa. The maximum tensile residual stress observed in the specimens decreased from 1060 MPa in the nominally treated specimens to 760 MPa for specimens pre-stressed to 230 MPa. Similarly, thickness of the compressive residual stress region increased and the depth at which maximum tensile residual stress occurred increased as the pre-stress during treatment was increased Overall, application of tensile elastic pre-stress during LASER hardening is beneficial to the development of compressive residual stress in AISI 4140, with minimal impact to the hardness attained from the treatment. The newly developed approach for LASER hardening may support efforts to increase both the wear and fatigue resistance of parts made from hardenable steels.

  11. THE STRESS STATE OF THE RADIALLY INHOMOGENEOUS HEMISPHERICAL SHELL UNDER LOCALLY DISTRIBUTED VERTICAL LOAD

    Directory of Open Access Journals (Sweden)

    Andreev Vladimir Igorevich

    2018-01-01

    Full Text Available Subject: one of the promising trends in the development of structural mechanics is the development of methods for solving problems in the theory of elasticity for bodies with continuous inhomogeneity of any deformation characteristics: these methods make it possible to use the strength of the material most fully. In this paper, we consider the two-dimensional problem for the case when a vertical, locally distributed load acts on the hemisphere and the inhomogeneity is caused by the influence of the temperature field. Research objectives: derive governing system of equations in spherical coordinates for determination of the stress state of the radially inhomogeneous hemispherical shell under locally distributed vertical load. Materials and methods: as a mechanical model, we chose a thick-walled reinforced concrete shell (hemisphere with inner and outer radii a and b, respectively, b > a. The shell’s parameters are a = 3.3 m, b = 4.5 m, Poisson’s ratio ν = 0.16; the load parameters are f = 10MPa - vertical localized load distributed over the outer face, θ0 = 30°, temperature on the internal surface of the shell Ta = 500 °C, temperature on the external surface of the shell Tb = 0 °C. The resulting boundary-value problem (a system of differential equations with variable coefficients is solved using the Maple software package. Results: maximal compressive stresses σr with allowance for material inhomogeneity are reduced by 10 % compared with the case when the inhomogeneity is ignored. But it is not so important compared with a 3-fold decrease in the tensile stress σθ on the inner surface and a 2-fold reduction in the tensile stress σθ on the outer surface of the hemisphere as concretes generally have a tensile strength substantially smaller than the compressive strength. Conclusions: the method presented in this article makes it possible to reduce the deformation characteristics of the material, i.e. it leads to a reduction in stresses

  12. Assessing Acculturative Stress of International Students at a U.S. Community College

    Science.gov (United States)

    Hansen, Hardaye R.; Shneyderman, Yuliya; McNamara, Gloria S.; Grace, Lisa

    2018-01-01

    Research shows that international college students experience high levels of acculturative stress, which can adversely impact their health and college success. The levels of immersion in one's native culture and the culture of the U.S. may impact levels of acculturative stress in international students. This cross-sectional study examined…

  13. Analysis of Acculturative Stress and Sociocultural Adaptation among International Students at a Non-Metropolitan University

    Science.gov (United States)

    Mahmood, Hajara; Burke, Monica Galloway

    2018-01-01

    This quantitative descriptive study analyzed levels of acculturative stress and sociocultural adaptation among international students at a non-metropolitan university in the United States related to certain demographic characteristics. Surveys were used to measure international students' levels of acculturative stress and sociocultural adaptation,…

  14. Acculturative Stress, Poor Mental Health and Condom-Use Intention among International Students in China

    Science.gov (United States)

    Yang, Ningxi; Xu, Yayun; Chen, Xinguang; Yu, Bin; Yan, Hong; Li, Shiyue

    2018-01-01

    Objectives: Engaging in sexual risk behaviour can be a maladaptive strategy for international students to deal with stress. This study examined the role of poor mental health in mediating the relationship between acculturative stress and condom-use intention among international students in Beijing, China. Methods: The study used a cross-sectional…

  15. Aspects of acculturation stress among international students attending a university in the USA.

    Science.gov (United States)

    Chavajay, Pablo; Skowronek, Jeffrey

    2008-12-01

    Acculturation stress reported by 130 international students attending a university in Utah for about 2 yr. was examined. On the Acculturative Stress Scale for International Students, few students reported experiencing acculturation stress, but responses to four open-ended questions indicated many students perceived experience of acculturation stresses related to discrimination, feelings of loneliness, and academic concerns. The contrast of findings for the scale scores and the open-ended questions indicate the complexity of assessing international students' acculturation experiences of living and studying in the USA and suggest the usefulness of complementary methodologies for assessing such experience.

  16. PREFACE: 7th International Conference on Modern Practice in Stress and Vibration Analysis

    Science.gov (United States)

    Dulieu-Barton, J. M.

    2009-07-01

    The proceedings contain the papers presented at the 7th International Conference on Modern Practice in Stress and Vibration Analysis. The collection of papers represents the range of activities that are carried out to understand the functionality of engineering systems and structures through stress/strain based evaluation and dynamic response. The scope is broad and covers theoretical studies, modelling and experimental evaluations. Many of the papers cover integration techniques and approaches to better understanding of system performance and failure. All of the papers have been peer reviewed by at least two experts and represent the state of the art of research in this area. The conference is the seventh in the series, following on from previous conferences in Bath, Glasgow, Nottingham, Dublin, Sheffield and Liverpool. Although based in the British Isles the conference has a truly international flavour with offerings from 22 countries. The conference is organised by the Institute of Physics Applied Mechanics Group (formerly the Stress and Vibration Group). It incorporates activities associated with the British Society for Strain Measurement including the Measurements Lecture, the EMex Exhibition and the Young Stress Analyst Competition. The organising committee is grateful for the support of all of the authors, the scientific committee and keynote speakers who played a significant role in the review process, to John Edwards who was instrumental in managing the paper review and submission process, Dawn Stewart and Claire Garland of the Institute of Physics for organising the conference, social programme and registration and Biana Gale of the British Society for Strain Measurement for organising the Exhibition. The organising committee is also grateful to the sponsors of the conference for their kind support and to the co-sponsors for distributing information on the conference. Professor Janice M Dulieu-Barton Professor of Experimental Mechanics University of

  17. Neutron depolarization study of internal stresses in amorphous Fe40Ni40B20

    International Nuclear Information System (INIS)

    de Jong, M.; Sietsma, J.; Rekveldt, M.T.; van den Beukel, A.

    1997-01-01

    The magnetic domain structure of amorphous ferromagnets with nonzero magnetostriction is mainly determined by the internal stress state because of the magneto-elastic coupling. The stress and field dependence of the domain structure contains important information on the internal stresses in the material. The three-dimensional neutron depolarization technique has been used to study the stress- and field-dependence of the bulk domain structures in both as-quenched and annealed ribbons of the metallic glass Fe 40 Ni 40 B 20 . A three-layer domain structure model corresponding to compressive and tensile internal stresses is presented to explain the measured data. The influence of surface roughness on the interpretation of neutron depolarization measurements in amorphous ribbons is discussed. Finally, the internal stress relaxation due to the annealing is explained in terms of the viscous behaviour of the glass. copyright 1997 American Institute of Physics

  18. Perceived Support as a Predictor of Acculturative Stress among International Students in the United States

    Science.gov (United States)

    Bai, Jieru

    2016-01-01

    A quantitative study was conducted to measure the acculturative stress of international students and investigate the predictors of acculturative stress. A total of 186 students participated in the survey. Results showed that 22.4% of the students in this study exceeded the normal stress level and might need counseling or psychological…

  19. Effects of Assertiveness Training and Expressive Writing on Acculturative Stress in International Students: A Randomized Trial

    Science.gov (United States)

    Tavakoli, Shedeh; Lumley, Mark A.; Hijazi, Alaa M.; Slavin-Spenny, Olga M.; Parris, George P.

    2009-01-01

    International university students often experience acculturative stress, and culturally appropriate techniques to manage stress are needed. This randomized trial tested the effects of group assertiveness training, private expressive writing, their combination, and a wait-list control on the acculturative stress, affect, and health of 118…

  20. Self-Critical Perfectionism, Acculturative Stress, and Depression among International Students

    Science.gov (United States)

    Rice, Kenneth G.; Choi, Chun-Chung; Zhang, Yanmei; Morero, Yanina Ines; Anderson, Debra

    2012-01-01

    The authors tested a classic diathesis-stress, stress-enhancement model of perfectionism with subgroups of Chinese (N = 129) and Asian Indian (N = 166) international graduate students attending a major U.S. university. More specifically, the authors tested whether self-critical perfectionism, acculturative stress, and their interaction accounted…

  1. Comparison of the stress distribution in the metallic layers of flexible pipes using two alternative Bflex formulations

    OpenAIRE

    Shi, Yunzhu

    2014-01-01

    Axisymmetric load is the most common load acting on flexible pipe. Modelling axisymmetric load correctly is very important to estimate the strength of a flexible pipe. The purpose of the thesis is to compare the stress distribution in metallic layers under three load case, i.e. tension, internal pressure and external pressure. Literature study and discussion to mechanical properties of flexible pipe and finite element modelling method are included in the thesis. The modelling program is BFLEX...

  2. Evidence for shear stress-mediated dilation of the internal carotid artery in humans

    DEFF Research Database (Denmark)

    Carter, Howard Henry; Atkinson, Ceri L; Heinonen, Ilkka H A

    2016-01-01

    -mediated dilation of larger conduit arteries in humans. There was a strong association between change in shear and diameter of the internal carotid (r=0.68; Ptime in humans, that shear stress is an important stimulus for hypercapnic vasodilation of the internal carotid...... increases carotid shear stress, a known stimulus to vasodilation in other conduit arteries. To explore the hypothesis that shear stress contributes to hypercapnic internal carotid dilation in humans, temporal changes in internal and common carotid shear rate and diameter, along with changes in middle.......01) carotids. Diameter also increased (Ptime course is associated with shear...

  3. Work stress and emotional exhaustion in nurses: the mediating role of internal locus of control.

    Science.gov (United States)

    Partlak Günüşen, Neslihan; Ustün, Besti; Erdem, Sabri

    2014-01-01

    Burnout is a major problem for nursing. There is a strong relationship between work stress and emotional exhaustion. Although studies report a negative correlation between the internal locus of control and emotional exhaustion and work stress, the number of studies available on the subject is limited. This study intends to examine the extent to which the relationship between work stress and emotional exhaustion is mediated by nurses' internal locus of control. The study adopted a cross-sectional survey design. The data were analyzed using structural equation modeling techniques. The study sample consisted of 347 nurses who worked in a university hospital in Izmir, Turkey and who agreed to participate in the study. The Work-Related Strain Inventory was used to evaluate the nurses' work stress level, Maslach Burnout Inventory was used to evaluate their emotional exhaustion levels, and the Locus of Control Scale was used to evaluate the internal locus of control. The variables of the study were based on the Neuman Systems Model. Work stress was positively related to internal locus of control (β3 = .21, p 0.1). Internal locus of control was negatively related to emotional exhaustion (β = -.14, p Work stress is directly (β = .87, p Work stress is directly (β = .87, p work stress was mediated, the impact of internal locus of control was limited. It is recommended that different variables be included in future studies so that they can mediate the relationship between work stress and emotional exhaustion.

  4. Visualizing Stress and Temperature Distribution During Elevated Temperature Deformation of IN-617 Using Nanomechanical Raman Spectroscopy

    Science.gov (United States)

    Zhang, Yang; Wang, Hao; Tomar, Vikas

    2018-04-01

    This work presents direct measurements of stress and temperature distribution during the mesoscale microstructural deformation of Inconel-617 (IN-617) during 3-point bending tests as a function of temperature. A novel nanomechanical Raman spectroscopy (NMRS)-based measurement platform was designed for simultaneous in situ temperature and stress mapping as a function of microstructure during deformation. The temperature distribution was found to be directly correlated to stress distribution for the analyzed microstructures. Stress concentration locations are shown to be directly related to higher heat conduction and result in microstructural hot spots with significant local temperature variation.

  5. Residual Stress Distribution In Heat Affected Zone Of Welded Steel By Means Of Neutron Diffraction Method

    International Nuclear Information System (INIS)

    Fajar, Andika; Prasuad; Gunawan; Muslich, M. Rifai

    1996-01-01

    Three dimensional residual stress distribution in the heat affected zone of 10 mm thick welded steel by means of neutron diffraction technique has been measured. The results showed that the residual stress was distributed near the welded metal, namely within about 46,25 mm. The major tensile stresses occurred in the X-direction, and they attained a level greater than 2000 MPa through the position far away fram the weld. The tensile stresses in the Y and Z- directions lied between 500 and 1500 MPa, The results also suggest that the stress in the surface was greater than that in the middle of the sample

  6. Bed shear stress distribution in straight channels with arbitrary cross section

    DEFF Research Database (Denmark)

    Christensen, Henrik Bo; Fredsøe, Jørgen

    1998-01-01

    The bed shear stress distribution in straight open channels is affected by mechanisms as bed curvature of the cross section profile, shear diffusion, and secondary currents. This paper compares some analytical and numerical methods to estimate the bed shear stress distribution. The methods...

  7. Coping, perceived stress, and job satisfaction among medical interns: The mediating effect of mindfulness

    Directory of Open Access Journals (Sweden)

    M Vinothkumar

    2016-01-01

    Full Text Available Background: Past research studies on the exploration of attributes to the stress of doctors/medical interns were reported more often than the types of coping strategies, healthy practices to strengthen their internal resources to deal effectively with the stressful situations. Objectives: The present study was conducted to find such internal resource – “mindfulness” as a mediator of coping, perceived stress, and job satisfaction among medical interns. Methods: A cross-sectional descriptive study comprised 120 medical interns forms from various medical colleges in Mangalore were recruited and completed the assessment on mindfulness, cognitive-emotive regulation, coping strategies, perceived stress, and job satisfaction from doctoral interns were collected. Results: Initial correlation analysis results indicate that adaptive coping strategies significantly associate with greater mindfulness and less perceived stress. In turn, mindfulness is negatively correlated with nonadaptive coping strategies and perceived. Job satisfaction showed no significant relationship with any of the other variables. Mediational models indicate that the relationship between adaptive coping strategies and perceived stress was significantly mediated by mindfulness. Furthermore, partial mediation between nonadaptive strategies and perceived stress through mindfulness indicates that respondents reported a high level of nonadaptive strategy experience and a lower level of mindfulness can be counterproductive as they encourage the ineffective way to deal with the stresses. Conclusion: The implication of the results were discussed with suggesting a possible intervention to improve the adaptive strategies and mindfulness among the medical interns.

  8. Coping, perceived stress, and job satisfaction among medical interns: The mediating effect of mindfulness.

    Science.gov (United States)

    Vinothkumar, M; Arathi, A; Joseph, Merin; Nayana, Prasad; Jishma, E Joshy; Sahana, U

    2016-01-01

    Past research studies on the exploration of attributes to the stress of doctors/medical interns were reported more often than the types of coping strategies, healthy practices to strengthen their internal resources to deal effectively with the stressful situations. The present study was conducted to find such internal resource - "mindfulness" as a mediator of coping, perceived stress, and job satisfaction among medical interns. A cross-sectional descriptive study comprised 120 medical interns forms from various medical colleges in Mangalore were recruited and completed the assessment on mindfulness, cognitive-emotive regulation, coping strategies, perceived stress, and job satisfaction from doctoral interns were collected. Initial correlation analysis results indicate that adaptive coping strategies significantly associate with greater mindfulness and less perceived stress. In turn, mindfulness is negatively correlated with nonadaptive coping strategies and perceived. Job satisfaction showed no significant relationship with any of the other variables. Mediational models indicate that the relationship between adaptive coping strategies and perceived stress was significantly mediated by mindfulness. Furthermore, partial mediation between nonadaptive strategies and perceived stress through mindfulness indicates that respondents reported a high level of nonadaptive strategy experience and a lower level of mindfulness can be counterproductive as they encourage the ineffective way to deal with the stresses. The implication of the results were discussed with suggesting a possible intervention to improve the adaptive strategies and mindfulness among the medical interns.

  9. Measurement of stress distributions in truck tyre contact patch in real rolling conditions

    Science.gov (United States)

    Anghelache, Gabriel; Moisescu, Raluca

    2012-12-01

    Stress distributions on three orthogonal directions have been measured across the contact patch of truck tyres using the complex measuring system that contains a transducer assembly with 30 sensing elements placed in the road surface. The measurements have been performed in straight line, in real rolling conditions. Software applications for calibration, data acquisition, and data processing were developed. The influence of changes in inflation pressure and rolling speed on the shapes and sizes of truck tyre contact patch has been shown. The shapes and magnitudes of normal, longitudinal, and lateral stress distributions, measured at low speed, have been presented and commented. The effect of wheel toe-in and camber on the stress distribution results was observed. The paper highlights the impact of the longitudinal tread ribs on the shear stress distributions. The ratios of stress distributions in the truck tyre contact patch have been computed and discussed.

  10. A numerical study on stress distribution across the ankle joint: Effects of material distribution of bone, muscle force and ligaments.

    Science.gov (United States)

    Mondal, Subrata; Ghosh, Rajesh

    2017-09-01

    The goal of this study is to develop a realistic three dimensional FE model of intact ankle joint. Three dimensional FE model of the intact ankle joint was developed using computed tomography data sets. The effect of muscle force, ligaments and proper material property distribution of bone on stress distribution across the intact ankle joint was studied separately. Present study indicates bone material property, ligaments and muscle force have influence on stress distribution across the ankle joint. Proper bone material, ligaments and muscle must be considered in the computational model for pre-clinical analysis of ankle prosthesis.

  11. Stress distribution in quasi-crystalline granular piles

    NARCIS (Netherlands)

    Trigger, S.A.; Heijst, van G.J.F.; Krasnopolskaya, T.S.; Schram, P.P.J.M.

    2001-01-01

    The main goal of this paper is a rigorous consideration of the stress problem in some simple models of granular piles. Discrete models are considered and the transition to the continuous description is accomplished in order to find the coarse-grained average stress. Some phenomenological rules are

  12. X-ray study of residual stress distribution of ground ceramics

    International Nuclear Information System (INIS)

    Sakaida, Yoshihisa; Tanaka, Keisuke; Ikuhara, Yuichi; Suzuki, Kenzi.

    1997-01-01

    The residual stress distribution of ground ceramics was determined from the eigen strain existing in the ground surface. The eigen strain of ground ceramics was tensile, and exponentially decreased with the distance from the surface. The residual stress distribution is given as a superposition of an exponential function of compression and a linear function. It is found that the actual residual stress distribution can be approximated by a compressive exponential function because the magnitude of tensile residual stress is negligibly small compared to the compressive residual stress. In the experiments, the diffraction angle was measured on ground silicon nitride for a wide range of sin 2 ψ using the glancing incidence X-ray diffraction technique. A strong nonlinearity was found in the 2θ-sin 2 ψ diagram at very high ψ-angles. From the analysis of nonlinearity, the residual stress distribution was determined. The residual stress distribution of silicon nitride coincided with the distribution calculated from the eigen strain distribution. Transmission electron microscopy was used to clarify the origin of generation of the residual stress. Both strain contrasts and microcracks were observed below the ground surface ; straight dislocations were also observed within silicon nitride grains near the ground surface. (author)

  13. Analytical model and application of stress distribution on mining coal floor

    Institute of Scientific and Technical Information of China (English)

    ZHU Shu-yun; JIAN Zhen-quan; HOU Hong-liang; XIAO Wei-guo; YAO Pu

    2008-01-01

    Given the analysis of underground pressure, a stress calculation model of coal floor stress has been established based on a theory of elasticity. The model presents the law of stress distribution on the relatively fixed position of the mining coal floor: the extent of stress variation in a fixed floor position decreases gradually along with depth, the decreasing rate of the vertical stress is clearly larger than that of the horizontal stress at a specific depth. The direction of the maximum principal stress changes gradually from a vertical direction to a horizontal direction with the advance of the working face. The deformation and permeability of the rock mass of the coal floor are obtained by contrasting the difference of the principal stress established from theoretical calculations with curves of stress-strain and permeability-strain from tests, which is an important mechanical basis for preventing water inrush from confined aquifers.

  14. Stress and coping strategies among nursing students: an international study.

    Science.gov (United States)

    Labrague, Leodoro J; McEnroe-Petitte, Denise M; Papathanasiou, Ioanna V; Edet, Olaide B; Tsaras, Konstantinos; Leocadio, Michael C; Colet, Paolo; Kleisiaris, Christos F; Fradelos, Evangelos C; Rosales, Rheajane A; Vera Santos-Lucas, Katherine; Velacaria, Pearl Irish T

    2017-12-20

    Mounting literature on stress and coping in nursing students are available; however, most of the findings are confined to a single cultural group. This study was conducted to determine the level of stress, its sources and coping strategies among nursing students from three countries: Greece, the Philippines and Nigeria. Using a descriptive, comparative research design, 547 nursing students (161 Greek nursing students, 153 Filipino nursing students, 233 Nigerian nursing students) participated in the study from August 2015 to April 2016. Two standardized instruments were used, the Perceived Stress Scale (PSS) and the Coping Behavior Inventory (CBI). Findings revealed that the degree of stress and the type of stressors and coping styles utilized by nursing students differ according to the country of origin. The year of study predicted overall stress (β = -0.149, p stress and lessen its impact such as stress management counseling, counseling programs, establishing peer and family support systems, and formulating hospital policies that will support nursing students.

  15. Income Distribution Determinants and Inequality – International Comparison

    OpenAIRE

    Škare, Marinko; Stjepanovic, Saša

    2014-01-01

    This study shows the relationship between income distribution and other relevant economic variables and their impact on income distribution. Panel data analysis is used to study 200 world economies and identify main income determinants. Using such a large panel to study income distribution and inequality of household income make empirical results of this study significant. Paper results show there is a large discrepancy of income distribution measured by household consumption for different cl...

  16. Finite element analysis of thermal stress distribution in different ...

    African Journals Online (AJOL)

    Nigerian Journal of Clinical Practice • Jan-Feb 2016 • Vol 19 • Issue 1. Abstract ... Key words: Amalgam, finite element method, glass ionomer cement, resin composite, thermal stress ... applications for force analysis and assessment of different.

  17. Income Distribution Determinants and Inequality – International Comparison

    Directory of Open Access Journals (Sweden)

    Marinko Škare

    2014-08-01

    Full Text Available This study shows the relationship between income distribution and other relevant economic variables and their impact on income distribution. Panel data analysis is used to study 200 world economies and identify main income determinants. Using such a large panel to study income distribution and inequality of household income make empirical results of this study significant. Paper results show there is a large discrepancy of income distribution measured by household consumption for different classes (income deciles. Inflation, unemployment, export, labour force, population and unemployment however are the main determinants between income distribution dynamics according to the result of this study.

  18. Job stress, satisfaction, and coping strategies among medical interns in a South Indian tertiary hospital.

    Science.gov (United States)

    Chandramouleeswaran, Susmita; Edwin, Natasha C; Braganza, Deepa

    2014-07-01

    It has previously been demonstrated that there is a significant drop in all domains of quality of life among interns during internship. A modified version of the health consultant's job stress and satisfaction questionnaire (HCJSSQ) was used to assess and quantify aspects of internship that were perceived as stressful and satisfying. Methods used to cope with work place stress were explored. A prospective cohort study was undertaken among 93 medical interns doing a rotating internship at the Christian Medical College and Hospital, a tertiary-care hospital in southern India. After completion of 6 months of internship, the modified version of the HCJSSQ was administered to all participants. The data were entered into Statistical Package for the Social Sciences (SPSS) Version 9 by double data entry technique. Percentages of interns reporting high levels of stress, satisfaction were calculated. While 63.4% of interns reported high levels of satisfaction, 45.2% of the interns experienced high levels of stress, 17.6% coped with work stress by using alcohol and nicotine, and 37% coped through unhealthy eating habits. More people found internship satisfying than stressful. However, a high proportion found it stressful, and many reported unhealthy coping mechanisms.

  19. The Co-Development of Parenting Stress and Childhood Internalizing and Externalizing Problems.

    Science.gov (United States)

    Stone, Lisanne L; Mares, Suzanne H W; Otten, Roy; Engels, Rutger C M E; Janssens, Jan M A M

    Although the detrimental influence of parenting stress on child problem behavior is well established, it remains unknown how these constructs affect each other over time. In accordance with a transactional model, this study investigates how the development of internalizing and externalizing problems is related to the development of parenting stress in children aged 4-9. Mothers of 1582 children participated in three one-year interval data waves. Internalizing and externalizing problems as well as parenting stress were assessed by maternal self-report. Interrelated development of parenting with internalizing and externalizing problems was examined using Latent Growth Modeling. Directionality of effects was further investigated by using cross-lagged models. Parenting stress and externalizing problems showed a decrease over time, whereas internalizing problems remained stable. Initial levels of parenting stress were related to initial levels of both internalizing and externalizing problems. Decreases in parenting stress were related to larger decreases in externalizing problems and to the (stable) course of internalizing problems. Some evidence for reciprocity was found such that externalizing problems were associated with parenting stress and vice versa over time, specifically for boys. Our findings support the transactional model in explaining psychopathology.

  20. The Role of Stress Exposure and Family Functioning in Internalizing Outcomes of Urban Families.

    Science.gov (United States)

    Sheidow, Ashli J; Henry, David B; Tolan, Patrick H; Strachan, Martha K

    2014-11-01

    Although research suggests that stress exposure and family functioning are associated with internalizing problems in adolescents and caregivers, surprisingly few studies have investigated the mechanisms that underlie this association. To determine whether family functioning buffers the development of internalizing problems in stress-exposed families, we assessed the relation between stress exposure, family functioning, and internalizing symptoms among a large sample of inner-city male youth and their caregivers living in poverty across five waves of data collection. We hypothesized that stress exposure and family functioning would predict development of subsequent youth and caregiver internalizing problems and that family functioning would moderate this relation, with higher functioning families demonstrating greater resiliency to stress exposure. We used a longitudinal, prospective design to evaluate whether family functioning (assessed at waves one through four) activated or buffered the effects of stress exposure (assessed at wave one) on subsequent internalizing symptoms (assessed at waves four and five). Stress from Developmental Transitions and family functioning were significant predictors of depressive symptoms and anxiety in youth; however, family functioning did not moderate the relation. Family functioning mediated the relation between stress from Daily Hassles and internalizing outcomes suggesting that poor parenting practices, low structure, and low emotional cohesion activate depression and anxiety in youth exposed to chronic and frequent everyday stressors. Surprisingly, only family functioning predicted depressive symptoms in caregivers. Results validate the use of a comprehensive, multi-informant assessment of stress when investigating internalizing outcomes in youth and support using family-based interventions in the treatment and prevention of internalizing.

  1. Measurement of lattice rotations and internal stresses in over one hundred individual grains during a stress-induced martensitic transformation

    Directory of Open Access Journals (Sweden)

    Hachi Younes El

    2015-01-01

    Full Text Available To better understand the properties of polycrystals at a microscopic scale during cyclic mechanical loading we have measured the relationship between grain orientations, their positions inside the sample and their internal stresses. In this work, in-situ 3DXRD technique was performed on over hundred grains during the stress-induced martensitic transformation in a Cu-Al-Be shape memory alloy. Information about the position, orientation, and stress field was obtained for each austenitic grain. These results have been used to develop a procedure that allows automatic processing for a large number of grains, matching them during loading and leads to a quantitative stress field. A strong heterogeneity of stress state between the grains at the surface and in the volume is evident.

  2. Impact of phytopathogen infection and extreme weather stress on internalization of Salmonella Typhimurium in lettuce.

    Science.gov (United States)

    Ge, Chongtao; Lee, Cheonghoon; Nangle, Ed; Li, Jianrong; Gardner, David; Kleinhenz, Matthew; Lee, Jiyoung

    2014-01-03

    Internalization of human pathogens, common in many types of fresh produce, is a threat to human health since the internalized pathogens cannot be fully inactivated/removed by washing with water or sanitizers. Given that pathogen internalization can be affected by many environmental factors, this study was conducted to investigate the influence of two types of plant stress on the internalization of Salmonella Typhimurium in iceberg lettuce during pre-harvest. The stresses were: abiotic (water stress induced by extreme weather events) and biotic (phytopathogen infection by lettuce mosaic virus [LMV]). Lettuce with and without LMV infection were purposefully contaminated with green fluorescence protein-labeled S. Typhimurium on the leaf surfaces. Lettuce was also subjected to water stress conditions (drought and storm) which were simulated by irrigating with different amounts of water. The internalized S. Typhimurium in the different parts of the lettuce were quantified by plate count and real-time quantitative PCR and confirmed with a laser scanning confocal microscope. Salmonella internalization occurred under the conditions outlined above; however internalization levels were not significantly affected by water stress alone. In contrast, the extent of culturable S. Typhimurium internalized in the leafy part of the lettuce decreased when infected with LMV under water stress conditions and contaminated with high levels of S. Typhimurium. On the other hand, LMV-infected lettuce showed a significant increase in the levels of culturable bacteria in the roots. In conclusion, internalization was observed under all experimental conditions when the lettuce surface was contaminated with S. Typhimurium. However, the extent of internalization was only affected by water stress when lettuce was infected with LMV. © 2013.

  3. Stress distribution in a transversely loaded cross-shaped single fiber SCS-6/Ti-6Al-4V composite

    International Nuclear Information System (INIS)

    Warrier, S.G.; Gundel, D.B.; Majumdar, B.S.; Miracle, D.B.

    1996-01-01

    In most structural applications utilizing fiber reinforced metal matrix composites (MMCs), the mechanical response normal to the fiber direction has to be considered. The transverse response is very sensitive to the interface bond strength, which has commonly been determined by testing straight-sided 90 degree specimens and interpreting debond initiation from the knee in the stress-strain curve as well as from a sudden drop in the Poisson's ratio. In an attempt to modify the debond initiation site to an internal location free of uncharacteristic states of stress, a cross-shaped specimen has been developed. Experiments conducted by Gundel et al. indicated that this geometry was successful in obtaining the appropriate crack initiation site. In the present study, finite element analysis (FEA) was done on the cross-shaped specimen to obtain the stress distribution in the composite under transverse loading, in an effort to corroborate the success of this geometry in determining the true transverse response of the composite

  4. Residual stress distribution in carbon steel pipe welded joint measured by neutron diffraction

    International Nuclear Information System (INIS)

    Hayashi, Makoto; Ishiwata, Masayuki; Morii, Yukio; Minakawa, Nobuaki

    2000-01-01

    In order to estimate crack growth behavior of fatigue and stress corrosion cracking in pipes, the residual stress distribution near the pipe weld region has to be measured through the wall thickness. Since the penetration depth of neutron is deep enough to pass through the thick pipe wall, the neutron diffraction technique for the residual stress measurement is effective for this purpose. At the first step the residual stress distribution near the weld region in a butt-welded carbon steel pipe was measured by the neutron diffraction. Significant stresses extended only to a distance of 30 mm from the center of the weld. The major tensile stresses occurred in the hoop direction in the fusion and heat affected zones of the weldment, and they attained a level greater than 200 MPa through the thickness. While the axial residual stress at the inside surface was 50 MPa, the stress at the outside surface was -100 MPa. The comparison of residual stress distributions measured by the neutron diffraction, the X-ray diffraction and the strain gauge method reveals that the neutron diffraction is the most effective for measuring the residual stress inside the structural components. (author)

  5. The Co-Development of Parenting Stress and Childhood Internalizing and Externalizing Problems

    OpenAIRE

    Stone, Lisanne L.; Mares, Suzanne H. W.; Otten, Roy; Engels, Rutger C. M. E.; Janssens, Jan M. A. M.

    2015-01-01

    Although the detrimental influence of parenting stress on child problem behavior is well established, it remains unknown how these constructs affect each other over time. In accordance with a transactional model, this study investigates how the development of internalizing and externalizing problems is related to the development of parenting stress in children aged 4-9. Mothers of 1582 children participated in three one-year interval data waves. Internalizing and externalizing problems as wel...

  6. Application of x-ray method for measuring internal stress in the gear teeth surface layer

    International Nuclear Information System (INIS)

    Zaborowski, T.

    1996-01-01

    This paper presents the methodics of the internal stress measurements concerning cylindrical gear teeth of involute profile. There are the method selected, relation between stress and strain presented and conditions of investigation discussed in the study, including preparation of samples for investigation and conditions of the strain measurement. Exemplifying results of stress measurements for teeth of gears made of 4OH steel are shown. Suitability of the developed investigation method is indicated

  7. Acculturative Stress, Parental and Professor Attachment, and College Adjustment in Asian International Students

    Science.gov (United States)

    Han, Suejung; Pistole, M. Carole; Caldwell, Jarred M.

    2017-01-01

    This study examined parental and professor attachment as buffers against acculturative stress and as predictors of college adjustment of 210 Asian international students (AISs). Moderated hierarchical regression analyses revealed that acculturative stress negatively and secure parental and professor attachment positively predicted academic…

  8. Multi-Dimensionality of Acculturative Stress among Chinese International Students: What Lies behind Their Struggles?

    Science.gov (United States)

    Zhang, Yue; Jung, Eunjoo

    2017-01-01

    This study aimed to identify the underlying dimensions of acculturative stress that Chinese international students may encounter in the U.S. In addition, we re-examined students' background characteristics and perceived social support from family, friends, and their school as predictors of students' different dimensions of acculturative stress. In…

  9. Estimation of residual stress distribution for pressurizer nozzle of Kori nuclear power plant considering safe end

    Energy Technology Data Exchange (ETDEWEB)

    Song, Tae Kwang; Bae, Hong Yeol; Chun, Yun Bae; Oh, Chang Young; Kim, Yun Jae [Korea University, Seoul (Korea, Republic of); Lee, Kyoung Soo; Park, Chi Yong [Korea Electric Power Research Institute, Daejeon (Korea, Republic of)

    2008-08-15

    In nuclear power plants, ferritic low alloy steel nozzle was connected with austenitic stainless steel piping system through alloy 82/182 butt weld. Accurate estimation of residual stress for weldment is important in the sense that alloy 82/182 is susceptible to stress corrosion cracking. There are many results which predict residual stress distribution for alloy 82/182 weld between nozzle and pipe. However, nozzle and piping system usually connected through safe end which has short length. In this paper, residual stress distribution for pressurizer nozzle of Kori nuclear power plant was predicted using FE analysis, which considered safe end. As a result, existing residual stress profile was redistributed and residual stress of inner surface was decreased specially. It means that safe end should be considered to reduce conservatism when estimating the piping system.

  10. Variation behavior of residual stress distribution by manufacturing processes in welded pipes of austenitic stainless steel

    International Nuclear Information System (INIS)

    Ihara, Ryohei; Hashimoto, Tadafumi; Mochizuki, Masahito

    2012-01-01

    Stress corrosion cracking (SCC) has been observed near heat affected zone (HAZ) of primary loop recirculation pipes made of low-carbon austenitic stainless steel type 316L in the nuclear power plants. For the non-sensitization material, residual stress is the important factor of SCC, and it is generated by machining and welding. In the actual plants, welding is conducted after machining as manufacturing processes of welded pipes. It could be considered that residual stress generated by machining is varied by welding as a posterior process. This paper presents residual stress variation due to manufacturing processes of pipes using X-ray diffraction method. Residual stress distribution due to welding after machining had a local maximum stress in HAZ. Moreover, this value was higher than residual stress generated by welding or machining. Vickers hardness also had a local maximum hardness in HAZ. In order to clarify hardness variation, crystal orientation analysis with EBSD method was performed. Recovery and recrystallization were occurred by welding heat near the weld metal. These lead hardness decrease. The local maximum region showed no microstructure evolution. In this region, machined layer was remained. Therefore, the local maximum hardness was generated at machined layer. The local maximum stress was caused by the superposition effect of residual stress distributions due to machining and welding. Moreover, these local maximum residual stress and hardness are exceeded critical value of SCC initiation. In order to clarify the effect of residual stress on SCC initiation, evaluation including manufacturing processes is important. (author)

  11. Update in the methodology of the chronic stress paradigm: internal control matters

    Directory of Open Access Journals (Sweden)

    Boyks Marco

    2011-04-01

    Full Text Available Abstract To date, the reliability of induction of a depressive-like state using chronic stress models is confronted by many methodological limitations. We believe that the modifications to the stress paradigm in mice proposed herein allow some of these limitations to be overcome. Here, we discuss a variant of the standard stress paradigm, which results in anhedonia. This anhedonic state was defined by a decrease in sucrose preference that was not exhibited by all animals. As such, we propose the use of non-anhedonic, stressed mice as an internal control in experimental mouse models of depression. The application of an internal control for the effects of stress, along with optimized behavioural testing, can enable the analysis of biological correlates of stress-induced anhedonia versus the consequences of stress alone in a chronic-stress depression model. This is illustrated, for instance, by distinct physiological and molecular profiles in anhedonic and non-anhedonic groups subjected to stress. These results argue for the use of a subgroup of individuals who are negative for the induction of a depressive phenotype during experimental paradigms of depression as an internal control, for more refined modeling of this disorder in animals.

  12. Update in the methodology of the chronic stress paradigm: internal control matters.

    Science.gov (United States)

    Strekalova, Tatyana; Couch, Yvonne; Kholod, Natalia; Boyks, Marco; Malin, Dmitry; Leprince, Pierre; Steinbusch, Harry Mw

    2011-04-27

    To date, the reliability of induction of a depressive-like state using chronic stress models is confronted by many methodological limitations. We believe that the modifications to the stress paradigm in mice proposed herein allow some of these limitations to be overcome. Here, we discuss a variant of the standard stress paradigm, which results in anhedonia. This anhedonic state was defined by a decrease in sucrose preference that was not exhibited by all animals. As such, we propose the use of non-anhedonic, stressed mice as an internal control in experimental mouse models of depression. The application of an internal control for the effects of stress, along with optimized behavioural testing, can enable the analysis of biological correlates of stress-induced anhedonia versus the consequences of stress alone in a chronic-stress depression model. This is illustrated, for instance, by distinct physiological and molecular profiles in anhedonic and non-anhedonic groups subjected to stress. These results argue for the use of a subgroup of individuals who are negative for the induction of a depressive phenotype during experimental paradigms of depression as an internal control, for more refined modeling of this disorder in animals.

  13. Yield stress distribution in injection-moulded glassy polymers

    NARCIS (Netherlands)

    Verbeeten, W.M.H.; Kanters, M.J.W.; Engels, T.A.P.; Govaert, L.E.

    2015-01-01

    A methodology for structural analysis simulations is presented that incorporates the distribution of mechanical propertiesalong the geometrical dimensions of injection-moulded amorphous polymer products. It is based on a previously developedmodelling approach, where the thermomechanical history

  14. Discrete element simulation of internal stress in SiCp/aluminum ...

    African Journals Online (AJOL)

    2002-07-22

    Jul 22, 2002 ... microcosmic two-dimensional numerical model of SiCp / Al matrix composites was established and the simulation of the size ... In the metal matrix composite ... stress and strain distribution, strengthen mechanisms and overall ...

  15. Internal stresses in steel plate generated by shape memory alloy inserts

    International Nuclear Information System (INIS)

    Malard, B.; Pilch, J.; Sittner, P.; Davydov, V.; Sedlák, P.; Konstantinidis, K.; Hughes, D.J.

    2012-01-01

    Graphical abstract: Display Omitted Highlights: ► Thermoresponsive internal stresses introduced into steel by embedding SMA inclusions. ► Neutron strain scanning on steel plate coupons with NiTi inserts at 21 °C and 130 °C. ► Internal stress field in steel evaluated directly from strains and by FE simulation. ► Internal stress generation by SMA insert resistant to thermal and mechanical fatigue. - Abstract: Neutron strain scanning was employed to investigate the internal stress fields in steel plate coupons with embedded prestrained superelastic NiTi shape memory alloy inserts. Strain fields in steel were evaluated at T = 21 °C and 130 °C on virgin coupons as well as on mechanically and thermally fatigued coupons. Internal stress fields were evaluated by direct calculation of principal stress components from the experimentally measured lattice strains as well as by employing an inverse finite element modeling approach. It is shown that if the NiTi inserts are embedded into the elastic steel matrix following a carefully designed technological procedure, the internal stress fields vary with temperature in a reproducible and predictable way. It is estimated that this mechanism of internal stress generation can be safely applied in the temperature range from −20 °C to 150 °C and is relatively resistant to thermal and mechanical fatigue. The predictability and fatigue endurance of the mechanism are of essential importance for the development of future smart metal matrix composites or smart structures with embedded shape memory alloy components.

  16. Biomechanical effects of two different collar implant structures on stress distribution under cantilever fixed partial dentures.

    Science.gov (United States)

    Merıç, Gökçe; Erkmen, Erkan; Kurt, Ahmet; Eser, Atilim; özden, Ahmet Utku

    2011-11-01

    The purpose of the study was to compare the effects of two distinct collar geometries of implants on stress distribution in the bone around the implants supporting cantilever fixed partial dentures (CFPDs) as well as in the implant-abutment complex and superstructures. The three-dimensional finite element method was selected to evaluate the stress distribution. CFPDs which was supported by microthread collar structured (MCS) and non-microthread collar structured (NMCS) implants was modeled; 300 N vertical, 150 N oblique and 60 N horizontal forces were applied to the models separately. The stress values in the bone, implant-abutment complex and superstructures were calculated. In the MCS model, higher stresses were located in the cortical bone and implant-abutment complex in the case of vertical load while decreased stresses in cortical bone and implant-abutment complex were noted within horizontal and oblique loading. In the case of vertical load, decreased stresses have been noted in cancellous bone and framework. Upon horizontal and oblique loading, a MCS model had higher stress in cancellous bone and framework than the NMCS model. Higher von Mises stresses have been noted in veneering material for NMCS models. It has been concluded that stress distribution in implant-supported CFPDs correlated with the macro design of the implant collar and the direction of applied force.

  17. Network integration of distributed generation: international research and development

    Energy Technology Data Exchange (ETDEWEB)

    Watson, J.

    2003-07-01

    This report provides information on privately and publicly funded research and development programmes in distributed generation (DG) in the USA, the European Union and Japan. Protection systems for the installation of DG, power electronics for the connection of DG to electricity distribution systems, reliability modelling, power quality issues, connection standards, and simulation and computer modelling are examined. The relevance of the programmes to the UK is considered.

  18. Flow through internal elastic lamina affects shear stress on smooth muscle cells (3D simulations).

    Science.gov (United States)

    Tada, Shigeru; Tarbell, John M

    2002-02-01

    We describe a three-dimensional numerical simulation of interstitial flow through the medial layer of an artery accounting for the complex entrance condition associated with fenestral pores in the internal elastic lamina (IEL) to investigate the fluid mechanical environment around the smooth muscle cells (SMCs) right beneath the IEL. The IEL was modeled as an impermeable barrier to water flow except for the fenestral pores, which were assumed to be uniformly distributed over the IEL. The medial layer was modeled as a heterogeneous medium composed of a periodic array of cylindrical SMCs embedded in a continuous porous medium representing the interstitial proteoglycan and collagen matrix. Depending on the distance between the IEL bottom surface and the upstream end of the proximal layer of SMCs, the local shear stress on SMCs right beneath the fenestral pore could be more than 10 times higher than that on the cells far removed from the IEL under the conditions that the fenestral pore diameter and area fraction of pores were kept constant at 1.4 microm and 0.05, respectively. Thus these proximal SMCs may experience shear stress levels that are even higher than endothelial cells exposed to normal blood flow (order of 10 dyn/cm(2)). Furthermore, entrance flow through fenestral pores alters considerably the interstitial flow field in the medial layer over a spatial length scale of the order of the fenestral pore diameter. Thus the spatial gradient of shear stress on the most superficial SMC is noticeably higher than computed for endothelial cell surfaces.

  19. Finite element based stress analysis of BWR internals exposed to accident loads

    Energy Technology Data Exchange (ETDEWEB)

    Altstadt, E; Weiss, F P; Werner, M; Willschuetz, H G

    1998-10-01

    During a hypothetical accident the reactor pressure vessel internals of boiling water reactors can be exposed to considerable loads resulting from temperature gradients and pressure waves. Three dimensional FE models were developed for the core shroud, the upper and the lower core supporting structure, the steam separator pipes and the feed water distributor. The models of core shroud, upper core structure and lower core structure were coupled by means of the substructure technique. All FE models can be used for thermal and for structural mechanical analyses. As an example the FE analysis for the case of a station black-out scenario (loss of power supply for the main circulating pumps) with subsequent emergency core cooling is demonstrated. The transient temperature distributions within the core shroud and within the steam dryer pipes as well were calculated based on the fluid temperatures and the heat transfer coefficients provided by thermo-hydraulic codes. At the maximum temperature gradients in the core shroud, the mechanical stress distribution was computed in a static analysis with the actual temperature field being the load. (orig.)

  20. «We were shocked»: Soviet captivity and internment as acculturation stress

    Directory of Open Access Journals (Sweden)

    Наталья Викторовна Суржикова

    2009-09-01

    Full Text Available N.V. Surzhikova's article based at the specific source type - memories - covers social and cultural issues of the Soviet captivity and internment. The author analyses manifestation of cultural shock or a stress of acculturation that proceeded from the direct contact of the prisoners and interned persons with another cultural conditions as well as mechanisms and limits of their adaptation.

  1. Factors Related to the Acculturation Stress of International Students in a Faith-Based Institution

    Science.gov (United States)

    de Souza, Liane Videres

    2012-01-01

    The number of international students attending American educational institutions is increasing annually. Based upon Maslow theory of needs, it was hypothesized that the acculturation process contributes to stress and anxiety among international students; therefore, it is important to understand some of the variables that influence this process for…

  2. Impact of Social Support and Coping on Acculturation and Acculturative Stress of East Asian International Students

    Science.gov (United States)

    Ra, Young-An; Trusty, Jerry

    2017-01-01

    The purpose of this study was to investigate the effects of social support and coping on acculturation and acculturative stress of international students. The authors used hierarchical multiple regression analysis to study a sample of 232 East Asian international students. The results indicate that social support and coping were partial mediators…

  3. The Interplay of International Students' Acculturative Stress, Social Support, and Acculturation Modes

    Science.gov (United States)

    Sullivan, Christopher; Kashubeck-West, Susan

    2015-01-01

    This study examined the relationship between acculturation modes (assimilation, integration, separation and marginalization), social support, and acculturative stress in undergraduate and graduate international students (N=104) at a medium-sized public university in the Midwestern United States. The study found that international students with…

  4. The Relationship Between Second Language Anxiety and International Nursing Students Stress

    Science.gov (United States)

    Khawaja, Nigar G.; Chan, Sabrina; Stein, Georgia

    2017-01-01

    We examined the relationship between second language anxiety and international nursing student stress after taking into account the demographic, cognitive, and acculturative factors. International nursing students (N = 152) completed an online questionnaire battery. Hierarchical regression analysis revealed that spoken second language anxiety and…

  5. Residual stress measurement of large scaled welded pipe using neutron diffraction method. Effect of SCC crack propagation and repair weld on residual stress distribution

    International Nuclear Information System (INIS)

    Suzuki, Hiroshi; Katsuyama, Jinya; Tobita, Tohru; Morii, Yukio

    2011-01-01

    The RESA-1 neutron engineering diffractometer in the JRR-3 (Japan Research Reactor No.3) at the Japan Atomic Energy Agency, which is used for stress measurements, was upgraded to realize residual stress measurements of large scaled mechanical components. A series of residual stress measurements was made to obtain through-thickness residual stress distributions in a Type 304 stainless steel butt-welded pipe of 500A-sch.80 using the upgraded RESA-1 diffractometer. We evaluated effects of crack propagation such as stress corrosion cracking (SCC) and a part-circumference repair weld on the residual stress distributions induced by girth welding. Measured residual stress distributions near original girth weld revealed good agreement with typical results shown in some previous works using finite element method, deep hole drilling as well as neutron diffraction. After introducing a mock crack with 10 mm depth in the heat affected zone on the inside wall of the pipe by electro discharge machining, the axial residual stresses were found to be released in the part of the mock crack. However, changes in the through-wall bending stress component and the self-equilibrated stress component were negligible and hence the axial residual stress distribution in the ligament was remained in the original residual stresses near girth weld without the mock crack. Furthermore, changes in hoop and radial residual stress were also small. The residual stress distributions after a part repair welding on the outer circumference of the girth weld were significantly different from residual stress distributions near the original girth weld. The through-thickness average axial residual stress was increased due to increase of the tensile membrane stress and mitigation of the bending stress after repair welding. Throughout above studies, we evidenced that the neutron diffraction technique is useful and powerful tool for measuring residual stress distributions in large as well as thick mechanical

  6. Effects of Prosthesis Stem Tapers on Stress Distribution of Cemented Hip Arthroplasty

    International Nuclear Information System (INIS)

    Abdullah, Abdul Halim; Nor, Mohd Asri Mohd; Saman, Alias Mohd; Tamin, Mohd Nasir; Kadir, Mohammed Rafiq Abdul

    2010-01-01

    Aseptic loosening effects are critical issues in encouraging long term stability of cemented hip arthroplasty. Stress shielding is believed to be an important factor that contributes to the aseptic loosening problems. The numerous changes in the prosthesis stem design are intended to minimize the stress shielding and aseptic loosening problems and to improve the long term performance of the implants. In this study, the stress distribution in cemented hip arthroplasty is established using finite element method. The taper of the prosthesis is designed to be 3 deg. at anterior/posterior, 3 deg. at medial/lateral and 10 deg. from wide lateral to narrow medial. Major muscle loads and contact forces are simulated for walking (toe-off phase) and stair climbing load cases. Effects of prosthesis stem tapers on the resulting stress distribution are investigated. Results show that compressive stress dominates in the medial plane while tensile stress in the lateral plane of the femur. The corresponding stress levels of intact femur for walking and stair-climbing load cases are 22 and 29 MPa, respectively. The magnitude of Tresca stress for the THA femur in stair-climbing load case remains higher in the region of 85 MPa while the walking load case induces around 40 MPa. The stress range in the straight and single taper stem prosthesis is lower than 260 MPa, while localized Tresca stress is in the order of the yield strength of Ti-6Al-4V alloy for double and triple taper stem design.

  7. Stress and strain distribution in three different mini dental implant designs using in implant retained overdenture: a finite element analysis study.

    Science.gov (United States)

    Aunmeungtong, W; Khongkhunthian, P; Rungsiyakull, P

    2016-01-01

    Finite Element Analysis (FEA) has been used for prediction of stress and strain between dental implant components and bone in the implant design process. Purpose of this study was to characterize and analyze stress and strain distribution occurring in bone and implants and to compare stress and strain of three different implant designs. Three different mini dental implant designs were included in this study: 1. a mini dental implant with an internal implant-abutment connection (MDIi); 2. a mini dental implant with an external implant-abutment connection (MDIe); 3. a single piece mini dental implant (MDIs). All implant designs were scanned using micro-CT scans. The imaging details of the implants were used to simulate models for FEA. An artificial bone volume of 9×9 mm in size was constructed and each implant was placed separately at the center of each bone model. All bone-implant models were simulatively loaded under an axial compressive force of 100 N and a 45-degree force of 100 N loading at the top of the implants using computer software to evaluate stress and strain distribution. There was no difference in stress or strain between the three implant designs. The stress and strain occurring in all three mini dental implant designs were mainly localized at the cortical bone around the bone-implant interface. Oblique 45° loading caused increased deformation, magnitude and distribution of stress and strain in all implant models. Within the limits of this study, the average stress and strain in bone and implant models with MDIi were similar to those with MDIe and MDIs. The oblique 45° load played an important role in dramatically increased average stress and strain in all bone-implant models. Mini dental implants with external or internal connections have similar stress distribution to single piece mini dental implants. In clinical situations, the three types of mini dental implant should exhibit the same behavior to chewing force.

  8. Effects on Subtalar Joint Stress Distribution After Cannulated Screw Insertion at Different Positions and Directions.

    Science.gov (United States)

    Yuan, Cheng-song; Chen, Wan; Chen, Chen; Yang, Guang-hua; Hu, Chao; Tang, Kang-lai

    2015-01-01

    We investigated the effects on subtalar joint stress distribution after cannulated screw insertion at different positions and directions. After establishing a 3-dimensional geometric model of a normal subtalar joint, we analyzed the most ideal cannulated screw insertion position and approach for subtalar joint stress distribution and compared the differences in loading stress, antirotary strength, and anti-inversion/eversion strength among lateral-medial antiparallel screw insertion, traditional screw insertion, and ideal cannulated screw insertion. The screw insertion approach allowing the most uniform subtalar joint loading stress distribution was lateral screw insertion near the border of the talar neck plus medial screw insertion close to the ankle joint. For stress distribution uniformity, antirotary strength, and anti-inversion/eversion strength, lateral-medial antiparallel screw insertion was superior to traditional double-screw insertion. Compared with ideal cannulated screw insertion, slightly poorer stress distribution uniformity and better antirotary strength and anti-inversion/eversion strength were observed for lateral-medial antiparallel screw insertion. Traditional single-screw insertion was better than double-screw insertion for stress distribution uniformity but worse for anti-rotary strength and anti-inversion/eversion strength. Lateral-medial antiparallel screw insertion was slightly worse for stress distribution uniformity than was ideal cannulated screw insertion but superior to traditional screw insertion. It was better than both ideal cannulated screw insertion and traditional screw insertion for anti-rotary strength and anti-inversion/eversion strength. Lateral-medial antiparallel screw insertion is an approach with simple localization, convenient operation, and good safety. Copyright © 2015 American College of Foot and Ankle Surgeons. Published by Elsevier Inc. All rights reserved.

  9. Evaluating stress distribution in two different designs of class I partial removable dentures

    Directory of Open Access Journals (Sweden)

    F. Geramipanah

    1998-05-01

    Full Text Available In Present study a digital model of hemimaxillectomy was reconstructed by computer and stress distribution of removable partial dentures in tissues, periodontal ligament and bone were thoroughly evaluated. The maximum stress of two different removable partial denture designs which contained buccal and lingual c-shaped clasps respectively were analyzed and compared. It was assumed that a 90 gram force which is equal to an average obturator’s weight is applied outwardly. The results showed that the maximum stress distribution in these two designs is not significantly different.

  10. Nonlocal approach to the analysis of the stress distribution in granular systems. I. Theoretical framework

    Science.gov (United States)

    Kenkre, V. M.; Scott, J. E.; Pease, E. A.; Hurd, A. J.

    1998-05-01

    A theoretical framework for the analysis of the stress distribution in granular materials is presented. It makes use of a transformation of the vertical spatial coordinate into a formal time variable and the subsequent study of a generally non-Markoffian, i.e., memory-possessing (nonlocal) propagation equation. Previous treatments are obtained as particular cases corresponding to, respectively, wavelike and diffusive limits of the general evolution. Calculations are presented for stress propagation in bounded and unbounded media. They can be used to obtain desired features such as a prescribed stress distribution within the compact.

  11. Stress and Friction Distribution around Slab Corner in Continuous Casting Mold with Different Corner Structures

    Science.gov (United States)

    Yu, Sheng; Long, Mujun; Chen, Huabiao; Chen, Dengfu; Liu, Tao; Duan, Huamei; Cao, Junsheng

    2018-06-01

    The non-uniform friction and thermal stress in the mold are important as causes of the transverse cracks around strand corner. To analyze the stress distribution features around strand corner, a three-dimensional thermo-elastoplastic finite-element mold model with different corner structures (right-angle, big-chamfer, multi-chamfer, and fillet) was established. The temperature field in the mold was indirectly coupled through a three-dimensional fluid flow and heat transfer model. In addition, the non-uniform mold friction stress loaded on the strand surface was calculated through a friction model. The results show that the stress distribution on the shell is similar to the temperature distribution. The stress concentration appears in the strand corner and the lower part of wide face. The friction stress enhances the corner stress around the edge of the air-gap. For chamfered molds, the stress around the corner between the wide face and chamfer face is larger than that between the narrow face and chamfer face. Around the corner region, both the stress peak and the area of the large stress zone of the right-angle strand are the largest, while those of big-chamfered, multi-chamfered, and fillet strands decrease in that order. The stress peak position of the chamfered strands is closer to the mold exit than that of the right-angle strand. Compared with the use of the right-angle mold, the application of chamfered molds is able to reduce the stress concentration around the strand corner.

  12. Stress and Friction Distribution around Slab Corner in Continuous Casting Mold with Different Corner Structures

    Science.gov (United States)

    Yu, Sheng; Long, Mujun; Chen, Huabiao; Chen, Dengfu; Liu, Tao; Duan, Huamei; Cao, Junsheng

    2018-02-01

    The non-uniform friction and thermal stress in the mold are important as causes of the transverse cracks around strand corner. To analyze the stress distribution features around strand corner, a three-dimensional thermo-elastoplastic finite-element mold model with different corner structures (right-angle, big-chamfer, multi-chamfer, and fillet) was established. The temperature field in the mold was indirectly coupled through a three-dimensional fluid flow and heat transfer model. In addition, the non-uniform mold friction stress loaded on the strand surface was calculated through a friction model. The results show that the stress distribution on the shell is similar to the temperature distribution. The stress concentration appears in the strand corner and the lower part of wide face. The friction stress enhances the corner stress around the edge of the air-gap. For chamfered molds, the stress around the corner between the wide face and chamfer face is larger than that between the narrow face and chamfer face. Around the corner region, both the stress peak and the area of the large stress zone of the right-angle strand are the largest, while those of big-chamfered, multi-chamfered, and fillet strands decrease in that order. The stress peak position of the chamfered strands is closer to the mold exit than that of the right-angle strand. Compared with the use of the right-angle mold, the application of chamfered molds is able to reduce the stress concentration around the strand corner.

  13. An Analysis of Freight Forwarder Operations in an International Distribution Channel.

    Science.gov (United States)

    1987-01-01

    44 3. International Marketing Mix ....................... 45 4. Security Assistance Distribution Channel .......... 69 5...an item is ultimately derived from the interaction of variables in the marketing mix . Of those variables, the distribution functions seem to allow the...Component of the Marketing Mix ,"Proceedings, NCPDM Fall Meeting, National council of Physical Distribution Management, San Francisco, CA., 1982. 7

  14. Stress distribution of metatarsals during forefoot strike versus rearfoot strike: A finite element study.

    Science.gov (United States)

    Li, Shudong; Zhang, Yan; Gu, Yaodong; Ren, James

    2017-12-01

    Due to the limitations of experimental approaches, comparison of the internal deformation and stresses of the human man foot between forefoot and rearfoot landing is not fully established. The objective of this work is to develop an effective FE modelling approach to comparatively study the stresses and energy in the foot during forefoot strike (FS) and rearfoot strike (RS). The stress level and rate of stress increase in the Metatarsals are established and the injury risk between these two landing styles is evaluated and discussed. A detailed subject specific FE foot model is developed and validated. A hexahedral dominated meshing scheme was applied on the surface of the foot bones and skin. An explicit solver (Abaqus/Explicit) was used to stimulate the transient landing process. The deformation and internal energy of the foot and stresses in the metatarsals are comparatively investigated. The results for forefoot strike tests showed an overall higher average stress level in the metatarsals during the entire landing cycle than that for rearfoot strike. The increase rate of the metatarsal stress from the 0.5 body weight (BW) to 2 BW load point is 30.76% for forefoot strike and 21.39% for rearfoot strike. The maximum rate of stress increase among the five metatarsals is observed on the 1st metatarsal in both landing modes. The results indicate that high stress level during forefoot landing phase may increase potential of metatarsal injuries. Copyright © 2017 Elsevier Ltd. All rights reserved.

  15. theoretical investigation of stresses distributions in hollow sandcrete

    African Journals Online (AJOL)

    user

    The test thin plate distributes the load on the block and the hollow block is regarded as a two ... Some research works had been done on the relationship between cavity ... The results would help reduce the cost, labour and time necessary to.

  16. Distribution of Side Abutment Stress in Roadway Subjected to Dynamic Pressure and Its Engineering Application

    Directory of Open Access Journals (Sweden)

    Yao Qiangling

    2015-01-01

    Full Text Available The borehole stress-meter was employed in this study to investigate the distribution of the side abutment stress in roadway subjected to dynamic pressure. The results demonstrate that the side abutment stress of the mining roadway reaches a peak value when the distance to the gob is 8 m and the distribution curve of the side abutment stress can be divided into three zones: stress rising zone, stress stabilizing zone, and stress decreasing zone. Further numerical investigation was carried out to study the effect of the coal mass strength, coal seam depth, immediate roof strength, and thickness on the distribution of the side abutment stress. Based on the research results, we determined the reasonable position of the mining roadway and the optimal width of the barrier pillar. The engineering application demonstrates that the retention of the barrier pillar with a width of 5 m along the gob as the haulage roadway for the next panel is feasible, which delivers favorable technological and economic benefits.

  17. The Effect of Resection Angle on Stress Distribution after Root-End Surgery

    Science.gov (United States)

    Monteiro, Jaiane Bandoli; Dal Piva, Amanda Maria de Oliveira; Tribst, João Paulo Mendes; Borges, Alexandre Luiz Souto; Tango, Rubens Nisie

    2018-01-01

    Introduction: This study aimed to investigate the influence of the resection angle on the stress distribution of retrograde endodontic treated maxillary incisors under oblique-load application. Methods and Materials: A maxillary central incisor which was endodontically treated and restored with a fiber glass post was obtained in a 3-dimensional numerical model and distributed into three groups according to type of resection: control; restored with fiber post without retrograde obturation, R45 and R90 with 45º and 90º resection from tooth axial axis, respectively and restored with Fuji II LC (GC America). The numerical models received a 45º occlusal load of 200 N/cm2 on the middle of lingual surface. All materials and structures were considered linear elastic, homogeneous and isotropic. Numerical models were plotted and meshed with isoparametric elements, and the results were analyzed using maximum principal stress (MPS). Results: MPS showed greater stress values in the bone tissue for control group than the other groups. Groups with apicectomy showed acceptable stress distribution on the fiber post, cement layer and root dentin, presenting more improved values than control group. Conclusion: Apicectomy at 90º promotes more homogeneity on stress distribution on the fiber post, cement layer and root dentin, which suggests less probability of failure. However, due to its facility and stress distribution also being better than control group, apicectomy at 45° could be a good choice for clinicians. PMID:29707013

  18. Thermodynamic method for generating random stress distributions on an earthquake fault

    Science.gov (United States)

    Barall, Michael; Harris, Ruth A.

    2012-01-01

    This report presents a new method for generating random stress distributions on an earthquake fault, suitable for use as initial conditions in a dynamic rupture simulation. The method employs concepts from thermodynamics and statistical mechanics. A pattern of fault slip is considered to be analogous to a micro-state of a thermodynamic system. The energy of the micro-state is taken to be the elastic energy stored in the surrounding medium. Then, the Boltzmann distribution gives the probability of a given pattern of fault slip and stress. We show how to decompose the system into independent degrees of freedom, which makes it computationally feasible to select a random state. However, due to the equipartition theorem, straightforward application of the Boltzmann distribution leads to a divergence which predicts infinite stress. To avoid equipartition, we show that the finite strength of the fault acts to restrict the possible states of the system. By analyzing a set of earthquake scaling relations, we derive a new formula for the expected power spectral density of the stress distribution, which allows us to construct a computer algorithm free of infinities. We then present a new technique for controlling the extent of the rupture by generating a random stress distribution thousands of times larger than the fault surface, and selecting a portion which, by chance, has a positive stress perturbation of the desired size. Finally, we present a new two-stage nucleation method that combines a small zone of forced rupture with a larger zone of reduced fracture energy.

  19. Stress Distribution around Laser-Welded Cutting Wheels Using a Spherical Indentation

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Yun Hee; Lee, Wan Kyu; Jeong, In Hyeon; Nahm, Seung Hoon [KRISS, Daejeon (Korea, Republic of)

    2008-04-15

    A spherical indentation has been proposed as a nondestructive method of measuring local residual stress field in laser-voided joints. The apparent yield strengths interpreted from the spherical indentation data of as-welded cutting wheel were compared with the intrinsic yield strengths measured at nearly equivalent locations in annealed wheel. Their difference along the distance from the welding line is welding stress distribution because the intrinsic yield strength is invariant regardless of the elastic residual stress. The spherical indentations show that the laser-welded diamond cutting wheel displays a 10 min-wide distribution of the welding residual stress and has peak compressive and tensile stresses in the shank and tip regions, respectively.

  20. Impact of peak electricity demand in distribution grids: a stress test

    NARCIS (Netherlands)

    Hoogsteen, Gerwin; Molderink, Albert; Hurink, Johann L.; Smit, Gerardus Johannes Maria; Schuring, Friso; Kootstra, Ben

    2015-01-01

    The number of (hybrid) electric vehicles is growing, leading to a higher demand for electricity in distribution grids. To investigate the effects of the expected peak demand on distribution grids, a stress test with 15 electric vehicles in a single street is conducted and described in this paper.

  1. Fluid moderator control system reactor internals distribution system

    International Nuclear Information System (INIS)

    Fensterer, H.F.; Klassen, W.E.; Veronesi, L.; Boyle, D.E.; Salton, R.B.

    1987-01-01

    This patent describes a spectral shift pressurized water nuclear reactor employing a low neutron moderating fluid for the spectral shift including a reactor pressure vessel, a core comprising a plurality of fuel assemblies, a core support plate, apparatus comprising means for penetrating the reactor vessel for introducing the moderating fluid into the reactor vessel. Means associated with the core support plate for directly distributing the moderating fluid to and from the fuel assemblies comprises at least one inlet flow channel in the core plate; branch inlet feed lines connect to the inlet flow channel in the core plate; vertical inlet flow lines flow connected to the branch inlet feed lines; each vertical flow line communicates with a fuel assembly; the distribution means further comprise lines serving as return flow lines, each of which is connected to one of the fuel assemblies; branch exit flow lines in the core plate flow connected to the return flow lines of the fuel assembly; and at least one outlet flow channel flow connected to the branch exit flow lines; and a flow port interposed between the penetration means and the distribution means for flow connecting the penetration means with the distribution means

  2. Disordered long-range internal stresses in deformed copper and the mechanisms underlying plastic deformation

    International Nuclear Information System (INIS)

    Levine, Lyle E.; Geantil, Peter; Larson, Bennett C.; Tischler, Jonathan Z.; Kassner, Michael E.; Liu, Wenjun; Stoudt, Mark R.; Tavazza, Francesca

    2011-01-01

    Highlights: → Axial elastic strains were measured from numerous individual, contiguous dislocation cell walls and cell interiors. → The mean stresses for the cell walls and cell interiors were of opposite sign, in agreement with theoretical predictions. → The separation between the mean cell wall and cell interior stresses was about 20% of the flow stress. → Broad distributions of dipolar stresses were observed that are consistent with a simple size-scaling model. - Abstract: The strength of wavy glide metals increases dramatically during deformation as dislocations multiply and entangle, forming dense dislocation wall structures. Numerous competing models have been proposed for this process but experimental validation and guidance for further model development require new experimental approaches capable of resolving local stresses within the dislocation microstructure. We use three-dimensional X-ray microscopy combining submicrometer spatial resolution with diffracted-beam masking to make direct measurements of axial elastic strain (and thus stress) in individual dislocation cell walls and their adjacent cell interiors in heavily deformed copper. These spatially resolved measurements show broad, asymmetric distributions of dipolar stresses that directly discriminate between long-standing deformation models and demonstrate that the distribution of local stresses is statistically connected to the global behavior through simple rules.

  3. The Migration, Mental Stress, and Tobacco use of Internal Migrants in China: The Moderating Effect of the Social Context of the Host Society.

    Science.gov (United States)

    Xie, Shenghua

    2017-11-10

    Previous studies on the relationship between mental stress and the tobacco use of internal migrants have not fully considered the social context of the host society. This study aims to examine how mental stress influences cigarette smoking in internal migrants in China by considering the social context of the host society. We used the RUMiC data that were collected in 15 cities distributed throughout 9 provinces of China. A total of 8,446 and 5,426 migrant workers were interviewed in 2008 and 2009, respectively. We selected individuals based on the criteria of age, salary, and hukou status. A total of 8,880 observations are valid for this study. This research used the logistic regression method to test the association between mental stress and the tobacco use of internal migrants. The results show that mental stress is not necessarily associated with the tobacco use of internal migrants. However, the effects of mental stress on tobacco use are moderated by the social context of the host society. This article calls for more attention to be paid to the moderate effect of social context in the host society on the association between mental stress and cigarette smoking of internal migrants. Moreover, this article underscores the importance of factors related to local societies in making and enacting tobacco control policies for migrants in developing countries.

  4. Influence of ion irradiation on internal residual stress in DLC films

    Energy Technology Data Exchange (ETDEWEB)

    Karaseov, Platon A., E-mail: platon.karaseov@rphf.spbstu.r [St. Petersburg State Polytechnic University, Polytechnicheskaya St. 29, 195251 St. Petersburg (Russian Federation); Podsvirov, Oleg A.; Karabeshkin, Konstantin V. [St. Petersburg State Polytechnic University, Polytechnicheskaya St. 29, 195251 St. Petersburg (Russian Federation); Vinogradov, Andrei Ya. [Ioffe Physicotechnical Institute RAS, Polytechnicheskaya 26, 195252 St. Petersburg (Russian Federation); Azarov, Alexander Yu. [St. Petersburg State Polytechnic University, Polytechnicheskaya St. 29, 195251 St. Petersburg (Russian Federation); Karasev, Nikita N. [State University of Information Technologies, Mechanics and Optics, Sablinskaya Str. 14, 197101 St. Petersburg (Russian Federation); Titov, Andrei I.; Smirnov, Alexander S. [St. Petersburg State Polytechnic University, Polytechnicheskaya St. 29, 195251 St. Petersburg (Russian Federation)

    2010-10-01

    The dependence of internal residual stress in thin diamond-like carbon films grown on Si substrate by PECVD technique on most important growth parameters, namely RF-power, DC bias voltage and substrate temperature, is described. Results show that compressive stress reaches the highest value of 2.7 GPa at low RF-power and DC bias. Increase of substrate temperature from 250 to 350 {sup o}C leads to nonlinear increase of stress value. Inhomogeneity of residual stress along the film surface disappears when film is deposited at temperatures above 275 {sup o}C. Post-growth film irradiation by P{sup +} and In{sup +} ions cause decrease of compressive stress followed by its inversion to tensile. For all ion energy combinations used residual stress changes linearly with normalized fluence up to 0.2 DPA with slope (8.7 {+-} 1.3) GPa/DPA.

  5. Path Analysis of Acculturative Stress Components and Their Relationship with Depression Among International Students in China.

    Science.gov (United States)

    Liu, Yang; Chen, Xinguang; Li, Shiyue; Yu, Bin; Wang, Yan; Yan, Hong

    2016-12-01

    Acculturative stress prevents international students from adapting to the host culture, increasing their risk for depression. International students in China are a growing and at-risk population for acculturative stress and depression. With data from the International Student Health and Behaviour Survey (Yu et al., ) in China, seven acculturative stress components were detected in a previous study (Yu et al., ), including a central component (self-confidence), three distal components (value conflict, identity threat and rejection) and three proximal components (poor cultural competence, opportunity deprivation and homesickness). The current study extended the previous study to investigate the relationship between these components and depression with data also from International Student Health and Behaviour Survey. Participants were 567 students (59% male, 40.4% African, mean age = 22.75, SD = 4.11) recruited in Wuhan, China. The sample scored high on the Acculturative Stress Scale for International Students (M = 92.81, SD = 23.93) and Center for Epidemiologic Studies Short Depression Scale (M = 0.97, SD = 0.53). Acculturative stress was positively associated with depression; the association between the three distal stress components and depression was fully mediated through self-confidence, while the three proximal components had a direct effect and a self-confidence-mediated indirect effect. These findings extended the value of the previous study, highlighted the central role of self-confidence in understanding acculturative stress and depression and provided new data supporting more effective counselling for international students in China. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

  6. Frustration-induced internal stresses are responsible for quasilocalized modes in structural glasses

    Science.gov (United States)

    Lerner, Edan; Bouchbinder, Eran

    2018-03-01

    It has been recently shown [E. Lerner, G. Düring, and E. Bouchbinder, Phys. Rev. Lett. 117, 035501 (2016), 10.1103/PhysRevLett.117.035501] that the nonphononic vibrational modes of structural glasses at low frequencies ω are quasilocalized and follow a universal density of states D (ω ) ˜ω4 . Here we show that the gapless nature of the observed density of states depends on the existence of internal stresses that generically emerge in glasses due to frustration, thus elucidating a basic element underlying this universal behavior. Similarly to jammed particulate packings, low-frequency modes in structural glasses emerge from a balance between a local elasticity term and an internal stress term in the dynamical matrix, where the difference between them is orders of magnitude smaller than their typical magnitude. By artificially reducing the magnitude of internal stresses in a computer glass former in three dimensions, we show that a gap is formed in the density of states below which no vibrational modes exist, thus demonstrating the crucial importance of internal stresses. Finally, we show that while better annealing the glass upon cooling from the liquid state significantly reduces its internal stresses, the self-organizational processes during cooling render the gapless D (ω ) ˜ω4 density of state unaffected.

  7. Understanding Stress-Related Behavioral Phenotypes: Report from the 1st International Neuroscience Summer School and the 11th InternationalStress and Behavior” Conference

    Directory of Open Access Journals (Sweden)

    J. L. LaPorte

    2008-01-01

    Full Text Available The 1st International Neuroscience Summer School and the 11th International Multidisciplinary Neuroscience and Biopsychiatry Conference on Stress and Behavior were held in St. Petersburg, Russia, during May 9–20, 2008. The summer school gathered 30 talented young scientists from 15 countries worldwide, and was dedicated to different topics of behavioral neuroscience. Many interactive courses were provided on neuropharmacology, animal phenotyping, and biopsychology. The conference's excellent scientific and social program attracted almost 500 delegates from 40 countries from many areas of stress research. The eclectic interaction between medical doctors, basic scientists, psychologists, and students made for a productive and collaborative environment, which contributed greatly to the success of the school and conference.

  8. Effect of constraint condition and internal medium on residual stress under overlay welding for dissimilar metal welding

    International Nuclear Information System (INIS)

    Song, Tae Kwang; Kim, Yun Jae; Lee, Kyoung Soo; Park, Chi Yong; Kim, Jong Sung; Kim, Jin Weon

    2007-01-01

    In nuclear power plants, residual stress of dissimilar metal weld propagates cracks in the weld metal which is susceptible to stress corrosion cracking. Overlay welding is a process widely used to mitigate residual stress replacing inside tensile stress by compression stress. However, according to the result of this study the effect of overlay welding on residual stress depends on both internal medium and constraint condition. The purpose of this study is to maximize the positive effect of overlay welding by finite element analyses

  9. STRESS DISTRIBUTION IN THE STRATIFIED MASS CONTAINING VERTICAL ALVEOLE

    Directory of Open Access Journals (Sweden)

    Bobileva Tatiana Nikolaevna

    2017-08-01

    Full Text Available Almost all subsurface rocks used as foundations for various types of structures are stratified. Such heterogeneity may cause specific behaviour of the materials under strain. Differential equations describing the behaviour of such materials contain rapidly fluctuating coefficients, in view of this, solution of such equations is more time-consuming when using today’s computers. The method of asymptotic averaging leads to getting homogeneous medium under study to averaged equations with fixed factors. The present article is concerned with stratified soil mass consisting of pair-wise alternative isotropic elastic layers. In the results of elastic modules averaging, the present soil mass with horizontal rock stratification is simulated by homogeneous transversal-isotropic half-space with isotropy plane perpendicular to the standing axis. Half-space is loosened by a vertical alveole of circular cross-section, and virgin ground is under its own weight. For horizontal parting planes of layers, the following two types of surface conditions are set: ideal contact and backlash without cleavage. For homogeneous transversal-isotropic half-space received with a vertical alveole, the analytical solution of S.G. Lekhnitsky, well known in scientific papers, is used. The author gives expressions for stress components and displacements in soil mass for different marginal conditions on the alveole surface. Such research problems arise when constructing and maintaining buildings and when composite materials are used.

  10. Residual stress distribution analysis of heat treated APS TBC using image based modelling.

    Science.gov (United States)

    Li, Chun; Zhang, Xun; Chen, Ying; Carr, James; Jacques, Simon; Behnsen, Julia; di Michiel, Marco; Xiao, Ping; Cernik, Robert

    2017-08-01

    We carried out a residual stress distribution analysis in a APS TBC throughout the depth of the coatings. The samples were heat treated at 1150 °C for 190 h and the data analysis used image based modelling based on the real 3D images measured by Computed Tomography (CT). The stress distribution in several 2D slices from the 3D model is included in this paper as well as the stress distribution along several paths shown on the slices. Our analysis can explain the occurrence of the "jump" features near the interface between the top coat and the bond coat. These features in the residual stress distribution trend were measured (as a function of depth) by high-energy synchrotron XRD (as shown in our related research article entitled 'Understanding the Residual Stress Distribution through the Thickness of Atmosphere Plasma Sprayed (APS) Thermal Barrier Coatings (TBCs) by high energy Synchrotron XRD; Digital Image Correlation (DIC) and Image Based Modelling') (Li et al., 2017) [1].

  11. Analysis and measurement of residual stress distribution of vanadium/ceramics joints for fusion reactor applications

    International Nuclear Information System (INIS)

    Nemoto, Y.; Ueda, K.

    1998-01-01

    Vanadium alloys are considered as candidate structural materials for fusion reactor system. When vanadium alloys are used in fusion reactor system, joining with ceramics for insulating is one of material issues to be solved to make component of fusion reactor. In the application of ceramics/metal jointing and coating, residual stress caused by difference of thermal expansion rate between ceramics and metals is an important factor in obtaining good bonding strength and soundness of coating. In this work, residual stress distribution in direct diffusion bonded vanadium/alumina joint (jointing temperature: 1400 C) was measured by small area X-ray diffraction method. And the comparison of finite element method (FEM) analysis and actual stress distribution was carried out. Tensile stress concentration at the edge of the boundary of the joint in alumina was observed. The residual stress concentration may cause cracks in alumina, or failure of bonding. Actually, cracks in alumina caused by thermal stress after bonding at 1500 C was observed. The stress concentration of the joint must be reduced to obtain good bonded joint. Lower bonding temperature or to devise the shape of the outer surface of the joint will reduce the stress concentration. (orig.)

  12. The influence of die geometry on stress distribution by experimental and FEM simulation on electrolytic copper wiredrawing

    Directory of Open Access Journals (Sweden)

    Leonardo Kyo Kabayama

    2009-09-01

    Full Text Available The study of die geometry is vital in determining the surface and mechanical properties of drawn wires, and consequently, their application. In this work, annealed electrolytic copper wire (ETP, with 0.5 mm original diameter was reduced by 19% in dies with 2β = 10º and 18º and Hc = 35 and 50%. The best experimental results were then studied by the Finite Element Method to simulate residual stress distribution. The experimental results show that the friction coefficient decreases as the wire drawing speed increases, and that low 2β and Hc values bring about the most favorable wiredrawing conditions. The simulation shows a variation in the axial and radial tensions, both for the compression and traction stresses on all regions during the wire drawing process. In conclusion, the influence of the internal die geometry on the drawn wire is clarified.

  13. Search for stress dependence in the internal friction of fused silica

    International Nuclear Information System (INIS)

    Willems, Phil; Lamb, Corinne; Heptonstall, Alastair; Hough, Jim

    2003-01-01

    The quality factor (Q) of the vertical bounce mode of a fused silica fiber pendulum is measured at high and low stresses. The internal friction of fused silica fibers is found to be independent of stress from 12.8 to 213 MPa at a level of 1.6x10 -8 . Comparison with Q's of fiber bending modes is consistent with losses concentrated in the surface of the fiber

  14. Predicting developmental changes in internalizing symptoms: examining the interplay between parenting and neuroendocrine stress reactivity.

    Science.gov (United States)

    Kuhlman, Kate R; Olson, Sheryl L; Lopez-Duran, Nestor L

    2014-07-01

    In this study, we examined whether parenting and HPA-axis reactivity during middle childhood predicted increases in internalizing symptoms during the transition to adolescence, and whether HPA-axis reactivity mediated the impact of parenting on internalizing symptoms. The study included 65 children (35 boys) who were assessed at age 5, 7, and 11. Parenting behaviors were assessed via parent report at age 5 and 11. The child's HPA-axis reactivity was measured at age 7 via a stress task. Internalizing symptoms were measured via teacher reports at age 5 and 11. High maternal warmth at age 5 predicted lower internalizing symptoms at age 11. Also, high reported maternal warmth and induction predicted lower HPA-axis reactivity. Additionally, greater HPA-axis reactivity at age 7 was associated with greater increases in internalizing symptoms from age 5 to 11. Finally, the association between age 5 maternal warmth and age 11 internalizing symptoms was partially mediated by lower cortisol in response to the stress task. Thus, parenting behaviors in early development may influence the physiological stress response system and therefore buffer the development of internalizing symptoms during preadolescence when risk for disorder onset is high. © 2013 Wiley Periodicals, Inc.

  15. Low Vagal Tone Magnifies the Association Between Psychosocial Stress Exposure and Internalizing Psychopathology in Adolescents

    Science.gov (United States)

    McLaughlin, Katie A.; Rith-Najarian, Leslie; Dirks, Melanie A.; Sheridan, Margaret A.

    2014-01-01

    Vagal tone is a measure of cardiovascular function that facilitates adaptive responses to environmental challenge. Low vagal tone is associated with poor emotional and attentional regulation in children and has been conceptualized as a marker of sensitivity to stress. We investigated whether the associations of a wide range of psychosocial stressors with internalizing and externalizing psychopathology were magnified in adolescents with low vagal tone. Resting heart period data were collected from a diverse community sample of adolescents (ages 13–17; N =168). Adolescents completed measures assessing internalizing and externalizing psychopathology and exposure to stressors occurring in family, peer, and community contexts. Respiratory sinus arrhythmia (RSA) was calculated from the interbeat interval time series. We estimated interactions between RSA and stress exposure in predicting internalizing and externalizing symptoms and evaluated whether interactions differed by gender. Exposure to psychosocial stressors was associated strongly with psychopathology. RSA was unrelated to internalizing or externalizing problems. Significant interactions were observed between RSA and child abuse, community violence, peer victimization, and traumatic events in predicting internalizing but not externalizing symptoms. Stressors were positively associated with internalizing symptoms in adolescents with low RSA but not in those with high RSA. Similar patterns were observed for anxiety and depression. These interactions were more consistently observed for male than female individuals. Low vagal tone is associated with internalizing psychopathology in adolescents exposed to high levels of stressors. Measurement of vagal tone in clinical settings might provide useful information about sensitivity to stress in child and adolescent clients. PMID:24156380

  16. Do hospital shift charge nurses from different cultures experience similar stress? An international cross sectional study.

    Science.gov (United States)

    Admi, Hanna; Eilon-Moshe, Yael

    2016-11-01

    prerequisite educational program should be mandatory for nurses prior to their nomination as shift charge nurses. Programs should be tailored to address the stress experienced by shift charge nurses. Ongoing mentorship and workshops are recommended to develop and maintain leadership abilities to cope with role stress. Future research should explore internationally the unique nature and stress of the shift charge nurse's role and replicate this study by using the Charge Nurse Stress Questionnaire in other countries. Further international comparative studies are recommended to evaluate stress perceptions of nurses in other roles and in different practice areas. Copyright © 2016 Elsevier Ltd. All rights reserved.

  17. Burnout and stress amongst interns in Irish hospitals: contributing factors and potential solutions.

    Science.gov (United States)

    Hannan, E; Breslin, N; Doherty, E; McGreal, M; Moneley, D; Offiah, G

    2018-05-01

    The transition from medical school to internship can be daunting for newly qualified doctors. High rates of stress and burnout have been reported, with negative impacts on patient care and physician wellbeing. We surveyed interns in our hospital group to evaluate rates of stress and burnout, as well as identify the causative factors and propose potential solutions to these. A hundred and one interns working in four different hospitals over a 2-year period were invited to participate in an anonymous survey. The survey collected basic demographic details and surveyed aspects of mental health using the burnout scale, Maslach Burnout Inventory (MBI) and the stress scale and 12-item General Health Questionnaire (GHQ-12). Interns were also asked to rate a variety of workplace factors on a Likert scale based on the degree of stress caused. Finally, they were surveyed on their awareness of support services available to them. Our results showed that 37% of interns met the criteria for psychological distress, high levels of emotional exhaustion, high depersonalisation and a low sense of personal accomplishment were reported in 55.4, 51.5 and 41.6%, respectively. Inadequate preparation for practice, financial worries, poor role definition and sleep deprivation were reported as significant stressors. Most were unaware of available support services and expressed interest in leaving Ireland after internship. Burnout and stress are significant problems amongst doctors in Irish hospitals. Ensuring better preparation for clinical practice and awareness of support services is vital to tackle this issue.

  18. Measurement of the residual stress distribution in a thick pre-stretched aluminum plate

    Science.gov (United States)

    Yuan, S. X.; Li, X. Q.; M, S.; Zhang, Y. C.; Gong, Y. D.

    2008-12-01

    Thick pre-stretched aluminum alloy plates are widely used in aircraft, while machining distortion caused by initial residual stress release in thick plates is a common and serious problem. To reduce the distortion, the residual stress distribution in thick plate must be measured. According to the characteristics of the thick pre-stretched aluminum alloy plate, based the elastic mechanical theory, this article deduces the modified layer-removal strain method adapting two different strain situations, which are caused by tensile and compressive stress. To validate this method, the residual stresses distribution along the thick direction of plate 2D70T351 is measured by this method, it is shown that the new method deduced in this paper is simple and accurate, and is very useful in engineering.

  19. Bayesian Approach for Constant-Stress Accelerated Life Testing for Kumaraswamy Weibull Distribution with Censoring

    Directory of Open Access Journals (Sweden)

    Abeer Abd-Alla EL-Helbawy

    2016-09-01

    Full Text Available The accelerated life tests provide quick information on the life time distributions by testing materials or products at higher than basic conditional levels of stress such as pressure, high temperature, vibration, voltage or load to induce failures. In this paper, the acceleration model assumed is log linear model. Constant stress tests are discussed based on Type I and Type II censoring. The Kumaraswmay Weibull distribution is used. The estimators of the parameters, reliability, hazard rate functions and p-th percentile at normal condition, low stress, and high stress are obtained. In addition, credible intervals for parameters of the models are constructed. Optimum test plan are designed. Some numerical studies are used to solve the complicated integrals such as Laplace and Markov Chain Monte Carlo methods.

  20. Bayesian Approach for Constant-Stress Accelerated Life Testing for Kumaraswamy Weibull Distribution with Censoring

    Directory of Open Access Journals (Sweden)

    Abeer Abd-Alla EL-Helbawy

    2016-12-01

    Full Text Available The accelerated life tests provide quick information on the life time distributions by testing materials or products at higher than basic conditional levels of stress such as pressure, high temperature, vibration, voltage or load to induce failures. In this paper, the acceleration model assumed is log linear model. Constant stress tests are discussed based on Type I and Type II censoring. The Kumaraswmay Weibull distribution is used. The estimators of the parameters, reliability, hazard rate functions and p-th percentile at normal condition, low stress, and high stress are obtained. In addition, credible intervals for parameters of the models are constructed. Optimum test plan are designed. Some numerical studies are used to solve the complicated integrals such as Laplace and Markov Chain Monte Carlo methods.

  1. Experimental Study of the Effect of Internal Defects on Stress Waves during Automated Fiber Placement

    Directory of Open Access Journals (Sweden)

    Zhenyu Han

    2018-04-01

    Full Text Available The detection technique of component defects is currently only realized to detect offline defects and online surface defects during automated fiber placement (AFP. The characteristics of stress waves can be effectively applied to identify and detect internal defects in material structure. However, the correlation mechanism between stress waves and internal defects remains unclear during the AFP process. This paper proposes a novel experimental method to test stress waves, where continuous loading induced by process itself is used as an excitation source without other external excitation. Twenty-seven groups of thermosetting prepreg laminates under different processing parameters are manufactured to obtain different void content. In order to quantitatively estimate the void content in the prepreg structure, the relation model between the void content and ultrasonic attenuation coefficient is revealed using an A-scan ultrasonic flaw detector and photographic methods by optical microscope. Furthermore, the high-frequency noises of stress waves are removed using Haar wavelet transform. The peaks, the Manhattan distance and mean stress during the laying process are analyzed and evaluated. Partial conclusions in this paper could provide theoretical support for online real-time detection of internal defects based on stress wave characteristics.

  2. Internal Stress Monitoring of In-Service Structural Steel Members with Ultrasonic Method

    Science.gov (United States)

    Li, Zuohua; He, Jingbo; Teng, Jun; Wang, Ying

    2016-01-01

    Internal stress in structural steel members is an important parameter for steel structures in their design, construction, and service stages. However, it is hard to measure via traditional approaches. Among the existing non-destructive testing (NDT) methods, the ultrasonic method has received the most research attention. Longitudinal critically refracted (Lcr) waves, which propagate parallel to the surface of the material within an effective depth, have shown great potential as an effective stress measurement approach. This paper presents a systematic non-destructive evaluation method to determine the internal stress in in-service structural steel members using Lcr waves. Based on theory of acoustoelasticity, a stress evaluation formula is derived. Factor of stress to acoustic time difference is used to describe the relationship between stress and measurable acoustic results. A testing facility is developed and used to demonstrate the performance of the proposed method. Two steel members are measured by using the proposed method and the traditional strain gauge method for verification. Parametric studies are performed on three steel members and the aluminum plate to investigate the factors that influence the testing results. The results show that the proposed method is effective and accurate for determining stress in in-service structural steel members. PMID:28773347

  3. Internal Stress Monitoring of In-Service Structural Steel Members with Ultrasonic Method.

    Science.gov (United States)

    Li, Zuohua; He, Jingbo; Teng, Jun; Wang, Ying

    2016-03-23

    Internal stress in structural steel members is an important parameter for steel structures in their design, construction, and service stages. However, it is hard to measure via traditional approaches. Among the existing non-destructive testing (NDT) methods, the ultrasonic method has received the most research attention. Longitudinal critically refracted (Lcr) waves, which propagate parallel to the surface of the material within an effective depth, have shown great potential as an effective stress measurement approach. This paper presents a systematic non-destructive evaluation method to determine the internal stress in in-service structural steel members using Lcr waves. Based on theory of acoustoelasticity, a stress evaluation formula is derived. Factor of stress to acoustic time difference is used to describe the relationship between stress and measurable acoustic results. A testing facility is developed and used to demonstrate the performance of the proposed method. Two steel members are measured by using the proposed method and the traditional strain gauge method for verification. Parametric studies are performed on three steel members and the aluminum plate to investigate the factors that influence the testing results. The results show that the proposed method is effective and accurate for determining stress in in-service structural steel members.

  4. Radionuclides distribution in internal organs of wild animals in alienation zone of Chernobyl NPP

    International Nuclear Information System (INIS)

    Gorbatova, T.A.; Kudryashov, V.P.; Mironov, V.P.

    2002-01-01

    Activities of caesium 137, strontium 90, plutonium isotopes and americium 241 are experimentally defined in the internal organs of bearer and wolf alienation zone of Chernobyl NPP. Radionuclides distribution in the internal organs of wild animals is defined by destruction of nuclear fuel particles

  5. Distribution and natural history of stress fractures in U.S. Marine recruits

    International Nuclear Information System (INIS)

    Greaney, R.B.; Gerber, F.H.; Laughlin, R.L.; Kmet, J.P.; Metz, C.D.; Kilcheski, T.S.; Rao, B.R.; Silverman, E.D.

    1983-01-01

    In a prospective study of stress injuries of the lower extremities of U.S. Marine recruits, researchers derived a frequency distribution of stress fractures. The most frequently fractured bone was the tibia (73%), while the single most common site was the posterior calcaneal tuberosity (21%). The natural history of stress fractures by scintigraphy and radiography has been outlined, showing the evolutionary changes on either study as a universal progression independent of injury site or type of stress. An identical spectrum of changes should be present within any group undergoing intense new exercise. The frequency distribution of stress fractures should be a function of differing forms and intensities of exercise, therefore, our figures should not be applied to other groups. Researchers used the presence of a scintigraphic abnormality at a symptomatic site as the criterion for diagnosis of stress fracture. Since the distribution of skeletal radiotracer uptake is directly dependent on local metabolic activity, it is expected that a focal alteration in bone metabolism will result in a scintigram approaching 100% sensitivity for the abnormality (9). In the proper clinical setting, the specificity should approximate this figure; however, a focal, nonstress-related bone abnormality which has not manifested any radiographic change, such as early osteomyelitis, could result in a false-positive examination. Specificity cannot, therefore, be accurately determined without an actual determination of the pathologic changes within the bone, necessarily involving biopsy

  6. Selective Internal Heat Distribution in Modified Trombe Wall

    Science.gov (United States)

    Szyszka, Jerzy; Kogut, Janusz; Skrzypczak, Izabela; Kokoszka, Wanda

    2017-12-01

    At present, the requirements for thermal insulation of the external walls in buildings are being increased. There is a need to reduce energy consumption for heating rooms during the winter season. This may be achieved by increasing the thermal resistance of the outer partitions, using solutions that utilize either recuperation or solar radiation. The most popular systems include either solar collectors, or heat pump links or ground exchangers. Trombe walls (TW) are a very promising passive heating system, which requires little or no effort to operate, and may be very convenient in different climate conditions. A typical TW consists of a masonry wall painted a dark, heat absorbing paint colour and faced with a single or double layer of glass. The principle of operation is based on the photothermal conversion of solar radiation. There are various modifications of TW. They may improve the energy efficiency in relation to the climate conditions in which they operate. The hybrid solutions are also known. The efficiency of walls is related to the use of proper materials. In TW, the compromise should be sought between the thermal resistance and the ability to distribute heat from the absorbed energy of solar radiation. The paper presents an overview of the most commonly used solutions and discusses its own concept dedicated to the climate conditions of Central Europe.

  7. Measurements of three dimensional residual stress distribution on laser irradiated spot

    International Nuclear Information System (INIS)

    Tanaka, Hirotomo; Akita, Koichi; Ohya, Shin-ichi; Sano, Yuji; Naito, Hideki

    2004-01-01

    Three dimensional residual stress distributions on laser irradiated spots were measured using synchrotron radiation to study the basic mechanism of laser peening. A water-immersed sample of high tensile strength steel was irradiated with Q-switched and frequency-doubled Nd:YAG laser. The residual stress depth profile of the sample was obtained by alternately repeating the measurement and surface layer removal by electrolytic polishing. Tensile residual stresses were observed on the surface of all irradiated spots, whereas residual stress changed to compressive just beneath the surface. The depth of compressive residual stress imparted by laser irradiation and plastic deformation zone increased with increasing the number of laser pulses irradiated on the same spot. (author)

  8. The influence of muscle forces on the stress distribution in the lumbar spine

    DEFF Research Database (Denmark)

    Wong, C; Rasmussen, J; Simonsen, Erik B.

    2011-01-01

    muscles. Results: In general the von Mises stress was larger by 30 %, and even higher when looking at the von Mises stress distribution in the superio-anterior and central part of the vertebral body and in the pedicles. Conclusion: The application of spine muscles to a finite element model showed markedly...... larger von Mises stress responses in the central and anterior part of the vertebral body, which can be tolerated in the young and healthy spine, but it would increase the risk of compression fractures in the elderly, osteoporotic spine.......Introduction: Previous studies of bone stresses in the human lumbar spine have relied on simplified models when modeling the spinal musculature, even though muscle forces are likely major contributors to the stresses in the vertebral bones. Detailed musculoskeletal spine models have recently become...

  9. Yield shear stress model of magnetorheological fluids based on exponential distribution

    International Nuclear Information System (INIS)

    Guo, Chu-wen; Chen, Fei; Meng, Qing-rui; Dong, Zi-xin

    2014-01-01

    The magnetic chain model that considers the interaction between particles and the external magnetic field in a magnetorheological fluid has been widely accepted. Based on the chain model, a yield shear stress model of magnetorheological fluids was proposed by introducing the exponential distribution to describe the distribution of angles between the direction of magnetic field and the chain formed by magnetic particles. The main influencing factors were considered in the model, such as magnetic flux density, intensity of magnetic field, particle size, volume fraction of particles, the angle of magnetic chain, and so on. The effect of magnetic flux density on the yield shear stress was discussed. The yield stress of aqueous Fe 3 O 4 magnetreological fluids with volume fraction of 7.6% and 16.2% were measured by a device designed by ourselves. The results indicate that the proposed model can be used for calculation of yield shear stress with acceptable errors. - Highlights: • A yield shear stress model of magnetorheological fluids was proposed. • Use exponential distribution to describe the distribution of magnetic chain angles. • Experimental and predicted results were in good agreement for 2 types of MR

  10. Stress and turnover intent in international organizations: social support and work life balance as resources

    OpenAIRE

    Giauque, David; Anderfuhren-Biget, Simon; Varone, Frédéric

    2016-01-01

    This study investigates whether work opportunities have an impact on stress and the related turnover intentions of employees working in intergovernmental international organizations. It contextualizes the job resources and demands model within international organizations’ specific work conditions. The empirical test is based on original data from a survey administered in four major organizations of the United Nations system. Results demonstrate that social work opportunities and work-life bal...

  11. Determination of stress distribution in III-V single crystal layers for heterogeneous integration applications

    Energy Technology Data Exchange (ETDEWEB)

    Jackson, M.; Hayashi, S. [Dept. of Materials Science and Engineering, University of California, Los Angeles, CA 90095 (United States); Goorsky, M.S.; Sandhu, R.; Chang-Chien, P.; Gutierrez-Aitken, A.; Tsai, R. [Northrop Grumman Space Technology, Redondo Beach, CA 90278 (United States); Noori, A.; Poust, B. [Dept. of Materials Science and Engineering, University of California, Los Angeles, CA 90095 (United States); Northrop Grumman Space Technology, Redondo Beach, CA 90278 (United States)

    2007-08-15

    Double crystal X-ray diffraction imaging and a variable temperature stage are employed to determine the stress distribution in heterogeneous wafer bonded layers though the superposition of images produced at different rocking curve angles. The stress distribution in InP layers transferred to a silicon substrate at room temperature exhibits an anticlastic deformation, with different regions of the wafer experiencing different signs of curvature. Measurements at elevated temperatures ({<=}125 C) reveals that differences in thermal expansion coefficients dominate the stress and that interfacial particulates introduce very high local stress gradients that increase with increased temperature. For thinned GaAs substrates (100 {mu}m) bonded using patterned metal interlayers to a separate GaAs substrate at {approx}200 C, residual stresses are produced at room temperature due to local stress points from metallization contacts and vias and the complex stress patterns can be observed using the diffraction imaging technique. (copyright 2007 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  12. Show what you know and deal with stress yourself: a qualitative interview study of medical interns' perceptions of stress and gender.

    Science.gov (United States)

    Verdonk, Petra; Räntzsch, Viktoria; de Vries, Remko; Houkes, Inge

    2014-05-17

    Medical students report high stress levels and in particular, the clinical phase is a demanding one. The field of medicine is still described as having a patriarchal culture which favors aspects like a physicians' perceived certainty and rationalism. Also, the Effort-Recovery Model explains stress as coming from a discrepancy between job demands, job control, and perceived work potential. Gendered differences in stress are reported, but not much is known about medical interns' perceptions of how gender plays in relation to stress. The aim of this study is to explore how medical interns experience and cope with stress, as well as how they reflect on the gendered aspects of stress. In order to do this, we have performed a qualitative study. In 2010-2011, semi-structured qualitative interviews were conducted with seventeen medical interns across all three years of the Masters programme (6 male, 11 female) at a Dutch medical school. The interview guide is based on gender theory, the Effort-Recovery Model, and empirical literature. Transcribed interviews have been analyzed thematically. First, stress mainly evolves from having to prove one's self and show off competencies and motivation ("Show What You Know…"). Second, interns seek own solutions for handling stress because it is not open for discussion (… "And Deal With Stress Yourself"). Patient encounters are a source of pride and satisfaction rather than a source of stress. But interns report having to present themselves as 'professional and self-confident', remaining silent about experiencing stress. Female students are perceived to have more stress and to study harder in order to live up to expectations. The implicit message interns hear is to remain silent about insecurities and stress, and, in particular, female students might face disadvantages. Students who feel less able to manifest the 'masculine protest' may benefit from a culture that embraces more collaborative styles, such as having open conversation

  13. Exploring valid internal-control genes in Porphyra yezoensis (Bangiaceae) during stress response conditions

    Science.gov (United States)

    Wang, Wenlei; Wu, Xiaojie; Wang, Chao; Jia, Zhaojun; He, Linwen; Wei, Yifan; Niu, Jianfeng; Wang, Guangce

    2014-07-01

    To screen the stable expression genes related to the stress (strong light, dehydration and temperature shock) we applied Absolute real-time PCR technology to determine the transcription numbers of the selected test genes in P orphyra yezoensis, which has been regarded as a potential model species responding the stress conditions in the intertidal. Absolute real-time PCR technology was applied to determine the transcription numbers of the selected test genes in P orphyra yezoensis, which has been regarded as a potential model species in stress responding. According to the results of photosynthesis parameters, we observed that Y(II) and F v/ F m were significantly affected when stress was imposed on the thalli of P orphyra yezoensis, but underwent almost completely recovered under normal conditions, which were collected for the following experiments. Then three samples, which were treated with different grade stresses combined with salinity, irradiation and temperature, were collected. The transcription numbers of seven constitutive expression genes in above samples were determined after RNA extraction and cDNA synthesis. Finally, a general insight into the selection of internal control genes during stress response was obtained. We found that there were no obvious effects in terms of salinity stress (at salinity 90) on transcription of most genes used in the study. The 18S ribosomal RNA gene had the highest expression level, varying remarkably among different tested groups. RPS8 expression showed a high irregular variance between samples. GAPDH presented comparatively stable expression and could thus be selected as the internal control. EF-1α showed stable expression during the series of multiple-stress tests. Our research provided available references for the selection of internal control genes for transcripts determination of P. yezoensis.

  14. Effect of platform connection and abutment material on stress distribution in single anterior implant-supported restorations: a nonlinear 3-dimensional finite element analysis.

    Science.gov (United States)

    Carvalho, Marco Aurélio; Sotto-Maior, Bruno Salles; Del Bel Cury, Altair Antoninha; Pessanha Henriques, Guilherme Elias

    2014-11-01

    Although various abutment connections and materials have recently been introduced, insufficient data exist regarding the effect of stress distribution on their mechanical performance. The purpose of this study was to investigate the effect of different abutment materials and platform connections on stress distribution in single anterior implant-supported restorations with the finite element method. Nine experimental groups were modeled from the combination of 3 platform connections (external hexagon, internal hexagon, and Morse tapered) and 3 abutment materials (titanium, zirconia, and hybrid) as follows: external hexagon-titanium, external hexagon-zirconia, external hexagon-hybrid, internal hexagon-titanium, internal hexagon-zirconia, internal hexagon-hybrid, Morse tapered-titanium, Morse tapered-zirconia, and Morse tapered-hybrid. Finite element models consisted of a 4×13-mm implant, anatomic abutment, and lithium disilicate central incisor crown cemented over the abutment. The 49 N occlusal loading was applied in 6 steps to simulate the incisal guidance. Equivalent von Mises stress (σvM) was used for both the qualitative and quantitative evaluation of the implant and abutment in all the groups and the maximum (σmax) and minimum (σmin) principal stresses for the numerical comparison of the zirconia parts. The highest abutment σvM occurred in the Morse-tapered groups and the lowest in the external hexagon-hybrid, internal hexagon-titanium, and internal hexagon-hybrid groups. The σmax and σmin values were lower in the hybrid groups than in the zirconia groups. The stress distribution concentrated in the abutment-implant interface in all the groups, regardless of the platform connection or abutment material. The platform connection influenced the stress on abutments more than the abutment material. The stress values for implants were similar among different platform connections, but greater stress concentrations were observed in internal connections

  15. Elastic-plastic stress distributions near the endcap of a fuel element

    International Nuclear Information System (INIS)

    Tayal, M.; Hallgrimson, K.D.; Sejnoha, R.; Singh, P.N.

    1993-06-01

    This paper discusses the stress patterns in and near the endcap of a CANDU fuel element from the perspective of stress corrosion cracking. Simulations of out-reactor burst tests suggest that local plastic strains stay comparatively low for internal pressures below 26-30 MPa. Photoelastic measurements as well as analytical assessments show that the reentrant corner at the sheath/endcap junction results in high concentration of stresses and strains. Analytical assessments show that the in-reactor stresses and strains at the reentrant corner are highly multiaxial, and well into the plastic range. The maximum principal stress correlates well with the location and the direction of circumferential endcap cracks observed in fuel that failed in the Bruce reactor. Thus the maximum principal stress appears promising in ranking various geometries of the sheath/endcap junction with respect to their relative susceptibility to stress corrosion cracking. Design studies suggest that the most effective practical ways of lowering the stresses near the weld, in order of decreasing importance, are to provide a larger interference-free length between the ridge and the endcaps; to increase the pellet/sheath radial gap; to increase the pellet/endcap axial gap; and to keep the gas pressure low. (author). 16 refs., 16 figs

  16. Stress distributions due to hydrogen concentrations in electrochemically charged and aged austenitic stainless steel

    International Nuclear Information System (INIS)

    Rozenak, P.; Loew, A.

    2008-01-01

    As a result of hydrogen concentration gradients in type austenitic stainless steels, formed during electrochemical charging and followed by hydrogen loss during aging, at room temperature, surface stresses were developed. These stresses were measured by X-ray technique and the crack formation thus induced could be studied using equilibrium stress equations. After various electrochemical charging and aging times, X-ray diffraction patterns obtained from samples indicated that the reflected and broadened diffraction peaks are the result of the formation of a non-uniform but continuous solid solution in the austenitic matrix. Since both hydrogen penetrations during charging and hydrogen release during aging are diffusion controlled processes and huge hydrogen concentration gradients in the thin surface layer, at depths comparable with the depth of X-ray penetration, are observed. The non-uniform hydrogen concentration in the austenitic matrix, results to the non-uniform expansion of the atomic microstructure and latter inevitably leads to the development of internal stresses. The internal stresses development formulae's are very similar to those relating to non-uniform heating of the materials, where thermal stresses appear due to non-uniform expansion or contraction. The relevant well developed theory is applicable in our case of non-uniform hydrogen concentrations in a solid solution of electrochemically charged and aged austenitic matrix. A few cracks were present on the surface after some minutes of electrochemical charging and the severity of cracking increased as hydrogen was lost during subsequent aging. This is consistent with the expectation of high compressive stresses in the bulk of the specimen during charging and high tensile surface stresses (at the level of 1 x 10 11 Pa) during the aging process. These stresses can induce the formation of surface cracks during the aging process after electrochemical charging in the AISI 316 stainless steel

  17. A numerical study of internal brick stresses in AGR moderator bricks

    Energy Technology Data Exchange (ETDEWEB)

    McNally, K., E-mail: kevin.mcnally@hsl.gsi.gov.uk [Health and Safety Laboratory, Harpur Hill, Buxton, Derbyshire SK17 9JN (United Kingdom); Fahad, M. [NGRG, School of MACE, University of Manchester, Manchester M13 9PL (United Kingdom); Tan, E.; Warren, N. [Health and Safety Laboratory, Harpur Hill, Buxton, Derbyshire SK17 9JN (United Kingdom); Hall, G.N.; Marsden, B.J. [NGRG, School of MACE, University of Manchester, Manchester M13 9PL (United Kingdom)

    2016-12-01

    Highlights: • A methodology for studying the uncertainty in internal brick stresses was developed. • A computationally efficient methodology based upon a surrogate model was utilised. • Uncertainty in material relationships, particularly those related to secondary creep was the dominant source of uncertainty. - Abstract: Physically-based models are often used to model changes in geometry and the associated stress fields of graphite moderator bricks within an advanced gas-cooled reactor (AGR). These models require inputs that describe the loading conditions, and coded relationships describing the behaviour of material properties. Material relationships are primarily based upon data obtained from inspection campaigns at operating reactors. However, the data from trepanning campaigns do not provide information on some of the key relationships and parameters that affect the internal stresses generated within the moderator bricks. In this work we explore how uncertain material property relationships affect the internal brick stresses in early- and late-life. We describe two computer experiments designed to study early- and late-life brick stresses and report the results from global sensitivity analysis of the models. The work makes use of an emulator, a surrogate for the FE model, in order to make the sensitivity analyses computationally feasible.

  18. A numerical study of internal brick stresses in AGR moderator bricks

    International Nuclear Information System (INIS)

    McNally, K.; Fahad, M.; Tan, E.; Warren, N.; Hall, G.N.; Marsden, B.J.

    2016-01-01

    Highlights: • A methodology for studying the uncertainty in internal brick stresses was developed. • A computationally efficient methodology based upon a surrogate model was utilised. • Uncertainty in material relationships, particularly those related to secondary creep was the dominant source of uncertainty. - Abstract: Physically-based models are often used to model changes in geometry and the associated stress fields of graphite moderator bricks within an advanced gas-cooled reactor (AGR). These models require inputs that describe the loading conditions, and coded relationships describing the behaviour of material properties. Material relationships are primarily based upon data obtained from inspection campaigns at operating reactors. However, the data from trepanning campaigns do not provide information on some of the key relationships and parameters that affect the internal stresses generated within the moderator bricks. In this work we explore how uncertain material property relationships affect the internal brick stresses in early- and late-life. We describe two computer experiments designed to study early- and late-life brick stresses and report the results from global sensitivity analysis of the models. The work makes use of an emulator, a surrogate for the FE model, in order to make the sensitivity analyses computationally feasible.

  19. A Study of Stress Distribution in Layered and Gradient Tribological Coatings (Preprint)

    Science.gov (United States)

    2006-11-01

    FG) Ti/TiC coating design. On the top of the 440C stainless steel substrate, α-Ti is added as a bond layer with 50nm thickness to improve the... stainless steel substrate and the rigid spherical indenter was performed. Figure 5 (a) shows the normalized Hertzian point contact pressure distribution...AFRL-ML-WP-TP-2007-402 A STUDY OF STRESS DISTRIBUTION IN LAYERED AND GRADIENT TRIBOLOGICAL COATINGS (PREPRINT) Young Sup Kang, Shashi K

  20. X-ray fractography by using synchrotron radiation source. Residual stress distribution just beneath fatigue fracture surface

    International Nuclear Information System (INIS)

    Akita, Koichi; Yoshioka, Yasuo; Suzuki, Hiroshi; Sasaki, Toshihiko

    2000-01-01

    The residual stress distributions just beneath the fatigue fracture surface were measured using synchrotron radiation with three different wavelengths, i.e., three different penetration depths. The residual stress distributions were estimated from three kinds of diffraction data by the following process. First, a temporary residual stress distribution in the depth direction is assumed. Theoretical 2θ-sin 2 ψ diagrams for each wavelength, where each has a different penetration depth, are calculated by the cosψ method developed by one of the authors. The sum total of the differences between the theoretical and experimental values of the diffraction angle in 2θ-sin 2 ψ diagrams is calculated. This total value is minimized by changing the assumed stress distribution by the quasi-Newton optimization method. Finally, optimized 2θ-sin 2 ψ diagrams for each penetration depth and detailed stress distribution are determined. The true surface residual stress is obtained from this stress distribution. No effect of load ratio R (= P min /P max ) on the residual stresses of the fatigue fracture surfaces in low-carbon steels was observed when the sin 2 ψ method was used for stress measurement. However, the residual stresses became higher with increasing R when these were measured by the proposed method. On the basis of this, the stress intensity factor range, ΔK, can be estimated from the residual stress on the fatigue fracture surface. (author)

  1. Association of Acculturative Stress, Islamic Practices, and Internalizing Symptoms among Arab American Adolescents

    Science.gov (United States)

    Goforth, Anisa N.; Pham, Andy V.; Chun, Heejung; Castro-Olivo, Sara M.; Yosai, Erin R.

    2016-01-01

    Although the numbers of Arab American immigrant youth in schools is increasing, there is little understanding of their mental health and the sociocultural factors that might influence it. This study examined the relationship between 2 sociocultural factors (i.e., acculturative stress and religious practices) and internalizing symptoms in first-…

  2. Correlates and Predictors of Parenting Stress among Internationally Adopting Mothers: A Longitudinal Investigation

    Science.gov (United States)

    Viana, Andres G.; Welsh, Janet A.

    2010-01-01

    This study examined correlates and predictors of parenting stress among internationally adopting (IA) mothers with the goal of expanding the knowledge base on the experiences of adoptive parents. One hundred and forty-three IA mothers completed pre-adoption (Time 0) and six months post-adoption (Time 1) surveys with questions regarding child-,…

  3. The co-development of parenting stress and childhood internalizing and externalizing problems

    NARCIS (Netherlands)

    Stone, L.L.; Mares, S.H.W.; Otten, R.; Engels, R.C.M.E.; Janssens, J.M.A.M.

    2016-01-01

    Although the detrimental influence of parenting stress on child problem behavior is well established, it remains unknown how these constructs affect each other over time. In accordance with a transactional model, this study investigates how the development of internalizing and externalizing problems

  4. Evaluation of stress intensity factor for craks in surface of tubes with internal pressure

    International Nuclear Information System (INIS)

    Cesari, F.; Hellen, T.K.

    1977-01-01

    In this report the authors have examined the different methods for calculation of the stress intensity factor in tubes subject at internal pressure with surface cracks. The analysis includes cracks in 2-D axialsymmetric and 3-D. Moreover the authors have clarified the difference between the ASME Sec.11 and the procedure more rigorous

  5. Managing the Role Stress of Public Relations Practitioners in International Schools

    Science.gov (United States)

    Bunnell, Tristan

    2006-01-01

    This article examines the diverse role and work of public relations practitioners in the growing body of international schools. It examines evidence of "role stress" in the form of the subsets of role overload, role ambiguity, role conflict and role preparedness. Three particular aspects were identified. The role seems prone to change alongside…

  6. Monitoring stress among internal medicine residents: an experience-driven, practical and short measure.

    Science.gov (United States)

    Myszkowski, Nils; Villoing, Barbara; Zenasni, Franck; Jaury, Philippe; Boujut, Emilie

    2017-07-01

    Residents experience severely high levels of stress, depression and burnout, leading to perceived medical errors, as well as to symptoms of impairment, such as chronic anger, cognitive impairment, suicidal behavior and substance abuse. Because research has not yet provided a psychometrically robust population-specific tool to measure the level of stress of medicine residents, we aimed at building and validating such a measure. Using an inductive scale development approach, a short, pragmatic measure was built, based on the interviews of 17 medicine residents. The Internal Medicine Residency Stress Scale (IMRSS) was then administered in a sample of 259 internal medicine residents (199 females, 60 males, M Age  = 25.6) along with the Hospital Anxiety and Depression Scale, Maslach Burnout Inventory, Satisfaction With Life Scale and Ways of Coping Checklist. The IMRSS showed satisfactory internal reliability (Cronbach's α = .86), adequate structural validity - studied through Confirmatory Factor Analysis (χ 2 /df = 2.51, CFI = .94; SRMR = .037, RMSEA = .076) - and good criterion validity - the IMRSS was notably strongly correlated with emotional exhaustion (r = .64; p is recommended to quickly and frequently assess and monitor stress among internal medicine residents.

  7. Effect of processing conditions on residual stress distributions by bead-on-plate welding after surface machining

    International Nuclear Information System (INIS)

    Ihara, Ryohei; Mochizuki, Masahito

    2014-01-01

    Residual stress is important factor for stress corrosion cracking (SCC) that has been observed near the welded zone in nuclear power plants. Especially, surface residual stress is significant for SCC initiation. In the joining processes of pipes, butt welding is conducted after surface machining. Residual stress is generated by both processes, and residual stress distribution due to surface machining is varied by the subsequent butt welding. In previous paper, authors reported that residual stress distribution generated by bead on plate welding after surface machining has a local maximum residual stress near the weld metal. The local maximum residual stress shows approximately 900 MPa that exceeds the stress threshold for SCC initiation. Therefore, for the safety improvement of nuclear power plants, a study on the local maximum residual stress is important. In this study, the effect of surface machining and welding conditions on residual stress distribution generated by welding after surface machining was investigated. Surface machining using lathe machine and bead on plate welding with tungsten inert gas (TIG) arc under various conditions were conducted for plate specimens made of SUS316L. Then, residual stress distributions were measured by X-ray diffraction method (XRD). As a result, residual stress distributions have the local maximum residual stress near the weld metal in all specimens. The values of the local maximum residual stresses are almost the same. The location of the local maximum residual stress is varied by welding condition. It could be consider that the local maximum residual stress is generated by same generation mechanism as welding residual stress in surface machined layer that has high yield stress. (author)

  8. Deformation of a geo-medium with considering for internal self-balancing stresses

    Science.gov (United States)

    Lavrikov, S. V.; Revuzhenko, A. F.

    2016-11-01

    Based on the general concept of rock as a medium with inner sources and sinks of energy, the authors consider an approach to mathematical modeling of a geo-medium with account for internal self-balancing stresses. The description of stresses and strains at the level of microstructural elements and macrovolume of the medium uses methods of non-Archimedean analysis. The model allows describing the accumulation of elastic energy in the form of internal self-balancing stresses. A finite element algorithm and a software program for solving plane boundary-value problems have been developed. The calculated data on rock specimen compression are given. It is shown that the behavior of plastic deformation zones depends on the pre-assigned initial microstresses.

  9. Analysis of the international distribution of per capita CO2 emissions using the polarization concept

    International Nuclear Information System (INIS)

    Duro, Juan Antonio; Padilla, Emilio

    2008-01-01

    The concept of polarization is linked to the extent that a given distribution leads to the formation of homogeneous groups with opposing interests. This concept, which is basically different from the traditional one of inequality, is related to the level of inherent potential conflict in a distribution. The polarization approach has been widely applied in the analysis of income distribution. The extension of this approach to the analysis of international distribution of CO 2 emissions is quite useful as it gives a potent informative instrument for characterizing the state and evolution of the international distribution of emissions and its possible political consequences in terms of tensions and the probability of achieving agreements. In this paper we analyze the international distribution of per capita CO 2 emissions between 1971 and 2001 through the adaptation of the polarization concept and measures. We find that the most interesting grouped description deriving from the analysis is a two groups' one, which broadly coincide with Annex B and non-Annex B countries of the Kyoto Protocol, which shows the power of polarization analysis for explaining the generation of groups in the real world. The analysis also shows a significant reduction in international polarization in per capita CO 2 emissions between 1971 and 1995, but not much change since 1995, which might indicate that polarized distribution of emission is still one of the important factors leading to difficulties in achieving agreements for reducing global emissions. (author)

  10. Factors affecting stress distribution and displacements in crystals III-V grown by Czochralski method with liquid encapsulation

    International Nuclear Information System (INIS)

    Schvezov, C.E.; Samarasekera, I.; Weinberg, F.

    1988-01-01

    A mathematical model based on the finite element method for calculating temperature and shear stress distributions in III-V crystals grown by LEC technique was developed. The calculated temperature are in good agreements with the experimental measurements. The shear stress distribution was calculated for several environmental conditions. The results showed that the magnitude and the distribution of shear stresses are highly sensitive to the crystal environment, including thickness and temperature distribution in boron oxides and the gas. The shear stress is also strongly influenced by interface curvature and cystals radius. (author) [pt

  11. Determination of Hot-Carrier Distribution Functions in Uniaxially Stressed p-Type Germanium

    DEFF Research Database (Denmark)

    Christensen, Ove

    1973-01-01

    This paper gives a description of an experimental determination of distribution functions in k→ space of hot holes in uniaxially compressed germanium. The hot-carrier studies were made at 85°K at fields up to 1000 V/cm and uniaxial stresses up to 11 800 kg/cm2. The field and stress were always in...... probabilities with stress. A model based on the nonparabolicity of the upper p3 / 2 level is proposed for the negative differential conductivity in stressed p-type Ge....... function has been assumed. The parameters of the distribution function are then fitted to the experimental modulation. The calculation of absorption was performed numerically, using a four-band k→·p→ model. This model was checked for consistency by comparing with piezoabsorption measurements performed...... in thermal equilibrium. The average carrier energy calculated from the distribution function shows a fast increase with stress and almost saturates when the strain splitting of the two p3 / 2 levels reaches the optical-phonon energy. This saturation is interpreted in terms of the change in scattering...

  12. Stress Prediction for Distributed Structural Health Monitoring Using Existing Measurements and Pattern Recognition.

    Science.gov (United States)

    Lu, Wei; Teng, Jun; Zhou, Qiushi; Peng, Qiexin

    2018-02-01

    The stress in structural steel members is the most useful and directly measurable physical quantity to evaluate the structural safety in structural health monitoring, which is also an important index to evaluate the stress distribution and force condition of structures during structural construction and service phases. Thus, it is common to set stress as a measure in steel structural monitoring. Considering the economy and the importance of the structural members, there are only a limited number of sensors that can be placed, which means that it is impossible to obtain the stresses of all members directly using sensors. This study aims to develop a stress response prediction method for locations where there are insufficent sensors, using measurements from a limited number of sensors and pattern recognition. The detailed improved aspects are: (1) a distributed computing process is proposed, where the same pattern is recognized by several subsets of measurements; and (2) the pattern recognition using the subset of measurements is carried out by considering the optimal number of sensors and number of fusion patterns. The validity and feasibility of the proposed method are verified using two examples: the finite-element simulation of a single-layer shell-like steel structure, and the structural health monitoring of the space steel roof of Shenzhen Bay Stadium; for the latter, the anti-noise performance of this method is verified by the stress measurements from a real-world project.

  13. Statistics on Near Wall Structures and Shear Stress Distribution from 3D Holographic Measurement.

    Science.gov (United States)

    Sheng, J.; Malkiel, E.; Katz, J.

    2007-11-01

    Digital Holographic Microscopy performs 3D velocity measurement in the near-wall region of a turbulent boundary layer in a square channel over a smooth wall at Reτ=1,400. Resolution of ˜1μm over a sample volume of 1.5x2x1.5mm (x^+=50, y^+=60, z^+=50) is sufficient for resolving buffer layer and lower log layer structures, and for measuring instantaneous wall shear stress distributions from velocity gradients in the viscous sublayer. Results, based on 700 instantaneous realizations, provide detailed statistics on the spatial distribution of both wall stress components along with characteristic flow structures. Conditional sampling based on maxima and minima of wall shear stresses, as well as examination of instantaneous flow structures, lead to development of a conceptual model for a characteristic flow phenomenon that seems to generating extreme stress events. This structure develops as an initially spanwise vortex element rises away from the surface, due to local disturbance, causing a local stress minimum. Due to increasing velocity with elevation, this element bends downstream, forming a pair of inclined streamwise vortices, aligned at 45^0 to freestream, with ejection-like flow between them. Entrainment of high streamwise momentum on the outer sides of this vortex pair generates streamwise shear stress maxima, 70 δν downstream, which are displaced laterally by 35 δν from the local minimum.

  14. Evaluation of stress distribution characteristics on various bar designs of three-implant-supported mandibular overdentures

    Directory of Open Access Journals (Sweden)

    Emre Tokar

    2017-01-01

    Full Text Available Objective: Implant-supported-overdentures, instead of conventional complete dentures, are frequently recommended to rehabilitate patients having edentulous mandible. The aim of this study was to evaluate the stress distribution characteristics of mandibular implant-supported overdentures with four different bar attachment designs. Materials and Method: A photoelastic mandibular model with three implants (3.75 mm - 13 mm placed at the interforaminal region was generated from a cast of an edentulous mandible. Four mandibular bar overdenture designs were fabricated: bar-clip, bar-galvano, bar-locator, and bar-ceka. Axial vertical loads (135 N were applied to the central fossa of the right first molar area for each overdenture design. Stress concentrations were recorded photographically and analyzed visually. Results: The tested bar attachment designs revealed low and moderate stress levels. The lowest stress was observed with the bar-clip design, followed by bar-locator, bar-ceka, and bar-galvano designs. Conclusion: The loads were distributed to all of the implants. Studied designs experienced moderate stress levels around the loaded side implant. Bars with distally placed stud attachments and surface treatment with electroforming seems to increase stress levels around the implants.

  15. Influence of Sewer Sediments on Flow Friction and Shear Stress Distribution

    DEFF Research Database (Denmark)

    Perrusquia, G.; Petersen, O.; Larsen, Torben

    1995-01-01

    Most sewers contain more or less deposited sediments. The paper discusses the distribution of the boundary shear stresses and the hydraulic resistance in part-full sewer pipes with such deposited sediments. The discussion is based on a series of numerical experiments using a validated numerical...

  16. Is the wide distribution of aspen a result of its stress tolerance?

    Science.gov (United States)

    V. J. Lieffers; S. M. Landhausser; E. H. Hogg

    2001-01-01

    Populus tremuloides is distributed from drought-prone fringes of the Great Plains to extremely cold sites at arctic treeline. To occupy these conditions aspen appears to be more tolerant of stress than the other North American species of the genus Populus. Cold winters, cold soil conditions during the growing season, periodic drought, insect defoliation, and...

  17. Transient temperature and stress distributions in the pressure vessel's wall of a nuclear reactor

    International Nuclear Information System (INIS)

    Silva, G.A. da

    1979-01-01

    In order to calculate the temperature distribution in a reactor vessel wall which is under the effect of gamma radiation originated in the reactor core, a numerical solution is proposed. This problem may arise from a reactor cooling pump failure .The thermal stresses are also calculated. (Author) [pt

  18. The influence of initial defects on mechanical stress and deformation distribution in oxidized silicon

    Directory of Open Access Journals (Sweden)

    Kulinich O. A.

    2008-10-01

    Full Text Available The near-surface silicon layers in silicon – dioxide silicon systems with modern methods of research are investigated. It is shown that these layers have compound structure and their parameters depend on oxidation and initial silicon parameters. It is shown the influence of initial defects on mechanical stress and deformation distribution in oxidized silicon.

  19. Thermal stress comparison in modular power converter topologies for smart transformers in the electrical distribution system

    DEFF Research Database (Denmark)

    Andresen, Markus; Ma, Ke; Liserre, Marco

    2015-01-01

    A Smart Transformer (ST) can cover an important managing role in the future electrical distribution grid. For the moment, the reliability and cost are not competitive with traditional transformers and create a barrier for its application. This work conduct detail designs and analysis...... for a promising modular ST solution, which is composed of Modular Multi-level converter, Quad Active Bridge DC-DC converters, and two-level voltage source converters. The focus is put on the loading conditions and thermal stress of power semiconductor devices in order to discover critical parts of the whole...... system when performing various mission profiles in the realistic distribution grid. It is concluded that the thermal stress for all stages is low during normal operation and especially the isolation stage is stressed least....

  20. Parameter Estimations and Optimal Design of Simple Step-Stress Model for Gamma Dual Weibull Distribution

    Directory of Open Access Journals (Sweden)

    Hamdy Mohamed Salem

    2018-03-01

    Full Text Available This paper considers life-testing experiments and how it is effected by stress factors: namely temperature, electricity loads, cycling rate and pressure. A major type of accelerated life tests is a step-stress model that allows the experimenter to increase stress levels more than normal use during the experiment to see the failure items. The test items are assumed to follow Gamma Dual Weibull distribution. Different methods for estimating the parameters are discussed. These include Maximum Likelihood Estimations and Confidence Interval Estimations which is based on asymptotic normality generate narrow intervals to the unknown distribution parameters with high probability. MathCAD (2001 program is used to illustrate the optimal time procedure through numerical examples.

  1. A fully coupled finite element model for stress distribution in buried gas pipeline

    International Nuclear Information System (INIS)

    Yahya Sukirman; Zainal Zakaria; Woong Soon Yue

    2001-01-01

    The study of stress-strain relationship is very important in many designs of buried structures over the years. The behavior and mechanism between the interaction of soil and buried structures such as a natural pipeline will mostly contributes to the integrity of the pipeline. This paper presents a fully coupled finite element of consolidation analysis model to study the stress-strain distribution along a buried pipeline before it excess its maximum deformation limit. The behavior of the soil-pipeline system can be modelled by a non-linear elasto-plastic based on Mohr-Coulomb and critical state yield surfaces. The deformation and deflection of the pipeline due to drained and external loading condition will be considered here. Finally the stress-strain distribution of the buried pipeline will be utilised to obtain the maximum deformation limit and the deflection of the buried pipeline. (Author)

  2. A simplified method of evaluating the stress wave environment of internal equipment

    Science.gov (United States)

    Colton, J. D.; Desmond, T. P.

    1979-01-01

    A simplified method called the transfer function technique (TFT) was devised for evaluating the stress wave environment in a structure containing internal equipment. The TFT consists of following the initial in-plane stress wave that propagates through a structure subjected to a dynamic load and characterizing how the wave is altered as it is transmitted through intersections of structural members. As a basis for evaluating the TFT, impact experiments and detailed stress wave analyses were performed for structures with two or three, or more members. Transfer functions that relate the wave transmitted through an intersection to the incident wave were deduced from the predicted wave response. By sequentially applying these transfer functions to a structure with several intersections, it was found that the environment produced by the initial stress wave propagating through the structure can be approximated well. The TFT can be used as a design tool or as an analytical tool to determine whether a more detailed wave analysis is warranted.

  3. Adaptation of BAp crystal orientation to stress distribution in rat mandible during bone growth

    Energy Technology Data Exchange (ETDEWEB)

    Nakano, T; Fujitani, W; Ishimoto, T [Division of Materials and Manufacturing Science, Graduate School of Engineering, Osaka University, 2-1, Yamada-oka, Suita, Osaka 565-0871 (Japan); Umakoshi, Y [National Institute for Materials Science, 1-2-1, Sengen, Tsukuba, Ibaragi, 305-0471 (Japan)], E-mail: nakano@mat.eng.osaka-u.ac.jp

    2009-05-01

    Biological apatite (BAp) c-axis orientation strongly depends on stress distribution in vivo and tends to align along the principal stress direction in bones. Dentulous mandible is subjected to a complicated stress condition in vivo during chewing but few studies have been carried out on the BAp c-axis orientation; so the adaptation of BAp crystal orientation to stress distribution was examined in rat dentulous mandible during bone growth and mastication. Female SD rats 4 to 14 weeks old were prepared, and the bone mineral density (BMD) and BAp crystal orientation were analyzed in a cross-section of mandible across the first molar focusing on two positions: separated from and just under the tooth root on the same cross-section perpendicular to the mesiodistal axis. The degree of BAp orientation was analyzed by a microbeam X-ray diffractometer using Cu-K{alpha} radiation equipped with a detector of curved one-dimensional PSPC and two-dimensional PSPC in the reflection and transmission optics, respectively. BMD quickly increased during bone growth up to 14 weeks, although it was independent of the position from the tooth root. In contrast, BAp crystal orientation strongly depended on the age and the position from the tooth root, even in the same cross-section and direction, especially along the mesiodistal and the biting axes. With increased biting stress during bone growth, the degree of BAp orientation increased along the mesiodistal axis in a position separated from the tooth root more than that near the tooth root. In contrast, BAp preferential alignment clearly appeared along the biting axis near the tooth root. We conclude that BAp orientation rather than BMD sensitively adapts to local stress distribution, especially from the chewing stress in vivo in the mandible.

  4. Tissue distribution of 3H-corticosterone in response to stress

    International Nuclear Information System (INIS)

    Kolta, M.G.; Soliman, K.F.A.

    1981-01-01

    The level and distribution of 3 H-corticosterone ( 3 H-B) was investigated in adult male Sprague-Dawley rats in response to diethyl ether stress, epinephrine (EP) and/or dexamethasone administration. Diethyl ether stress caused a significant increase in the 3 H-B counts by some of the body tissues and brain regions studied. Plasma 3 H-B counts in the stressed rats were found to be twice as much as in the control animals. When EP (1.0 mg/kg) was injected, the tissue-plasma ratios of 3 H-B were significantly lower (P 3 H-B count in the plasma in response to diethyl ether stress or EP may indicate a decline in rate of corticosterone metabolism. (author)

  5. Propagation of internal stresses in composite materials during heating and cooling according to thermal cycles of welding

    International Nuclear Information System (INIS)

    Gukasyan, L.E.; Belov, V.V.

    1977-01-01

    Investigations of free thermal expansion of a composite material, of fibre and matrix during welding thermal cycle make it possible to estimate mean internal strain and stress in the composite components, as well as the residual internal stress and strain present in the composite material after manufacturing. The samples investigated consisted of nickel-chromium EhI445 alloy, reinforced by tungsten-rhenium alloy fibres. As the composite material was cooled and heated in course of welding, the stress and strain changed their sign twice, the first time upon heating, the second time upon cooling. After complete cooling of the composite material residual stresses in the fibre stay at the proportionality level, while those in the matrix are lower. Experimental evidence of internal stress and strain appearing in the composite material during heating are fairly consistent with calculations in the elastic region, if account is taken of the temperature of internal residual stress relaxation upon heating

  6. An Analysis of 19 International Case Studies of Stress Prevention Through Work Reorganization Using the Demand/Control Model

    Science.gov (United States)

    Karasek, Robert A.

    2004-01-01

    Nineteen international case studies of workplace stress prevention initiatives are analyzed. The focus of these cases, which span a variety of workplaces and locations, is on preventing stress through work reorganization rather than remedial approaches for stress relief. It is found that the majority of the occupations represented in the case…

  7. Stress intensity factors for complete internal and external cracks in spherical shells

    International Nuclear Information System (INIS)

    Chao, Y.J.; Chen, H.

    1989-01-01

    Cracks or flows found in the nuclear structure must be fully evaluated to assure the safety of the plant. The weight function method has been widely used in the determination of stress intensity factors for cracks under stress gradient e.g. for thermal shock loading. The unique features of the weight function method is that once the weight function for a particular cracked geometry is determined the stress intensity factors at the crack tip for any loading applied to the flawed structure can be calculated by a simple integration. In this paper the stress intensity factors of the complete, part-through internal and external cracks in a spherical shell are determined. The finite element method was used to develop the weight functions for the flawed geometry. The approximate crack surface profile was used to derive the weight functions. The stress intensity factors associated with the cracks in spherical shells under internal pressure are determined by both the weight functions and the direct finite element method

  8. Differential relations between youth internalizing/externalizing problems and cortisol responses to performance vs. interpersonal stress.

    Science.gov (United States)

    Laurent, Heidemarie; Vergara-Lopez, Chrystal; Stroud, Laura R

    2016-09-01

    Efforts to define hypothalamic-pituitary-adrenal (HPA) axis profiles conferring risk for psychopathology have yielded inconclusive results, perhaps in part due to limited assessment of the stress response. In particular, research has typically focused on HPA responses to performance tasks, while neglecting the interpersonal stressors that become salient during adolescence. In this study we investigated links between psychosocial adjustment - youth internalizing and externalizing problems, as well as competence - and HPA responses to both performance and interpersonal stressors in a normative sample of children and adolescents. Participants (n = 59) completed a set of performance (public speaking, mental arithmetic, mirror tracing) and/or interpersonal (peer rejection) tasks and gave nine saliva samples, which were assayed for cortisol. Hierarchical linear models of cortisol response trajectories in relation to child behavior checklist (CBCL) scores revealed stressor- and sex-specific associations. Whereas internalizing problems related to earlier peaking, less dynamic cortisol responses to interpersonal stress (across males and females), externalizing problems related to lower, earlier peaking and less dynamic cortisol responses to performance stress for males only, and competence-related to later peaking cortisol responses to interpersonal stress for females only. Implications for understanding contextual stress profiles underlying different forms of psychopathology are discussed.

  9. TEMP-STRESS analysis of a reinforced concrete vessel under internal pressure

    International Nuclear Information System (INIS)

    Marchertas, A.H.; Kennedy, J.M.; Pfeiffer, P.A.

    1987-01-01

    Prediction of the response of the Sandia National laboratory 1/6-scale reinforced concrete containment model test was obtained by Argonne National Laboratory (ANL) employing a computer program developed by ANL. The test model was internally pressurized to failure. The two-dimensional code TEMP-STRESS [1-5] has been developed at ANL for stress analysis of plane and axisymmetric 2-D reinforced structures under various thermal conditions. The program is applicable to a wide variety of nonlinear problems, and is utilized in the present study. The comparison of these pretest computations with test data on the containment model should be a good indication of the state of the code

  10. Stress Corrosion Evaluation of Various Metallic Materials for the International Space Station Water Recycling System

    Science.gov (United States)

    Torres, P. D.

    2015-01-01

    A stress corrosion evaluation was performed on Inconel 625, Hastelloy C276, titanium commercially pure (TiCP), Ti-6Al-4V, Ti-6Al-4V extra low interstitial, and Cronidur 30 steel as a consequence of a change in formulation of the pretreatment for processing the urine in the International Space Station Environmental Control and Life Support System Urine Processing Assembly from a sulfuric acid-based to a phosphoric acid-based solution. The first five listed were found resistant to stress corrosion in the pretreatment and brine. However, some of the Cronidur 30 specimens experienced reduction in load-carrying ability.

  11. Role of Reynolds stress and toroidal momentum transport in the dynamics of internal transport barriers

    International Nuclear Information System (INIS)

    Kim, S. S.; Jhang, Hogun; Diamond, P. H.

    2012-01-01

    We study the interplay between intrinsic rotation and internal transport barrier (ITB) dynamics through the dynamic change of the parallel Reynolds stress. Global flux-driven gyrofluid simulations are used for this study. In particular, we investigate the role of parallel velocity gradient instability (PVGI) in the ITB formation and the back transition. It is found that the excitation of PVGI is followed by a change in the Reynolds stress which drives a momentum redistribution. This significantly influences E×B shear evolution and subsequent ITB dynamics. Nonlocal interactions among fluctuations are also observed during the PVGI excitation, resulting in turbulence suppression at the ITB.

  12. A Microstructural Study of Load Distribution in Cartilage: A Comparison of Stress Relaxation versus Creep Loading

    Directory of Open Access Journals (Sweden)

    Ashvin Thambyah

    2015-01-01

    Full Text Available The compressive response of articular cartilage has been extensively investigated and most studies have focussed largely on the directly loaded matrix. However, especially in relation to the tissue microstructure, less is known about load distribution mechanisms operating outside the directly loaded region. We have addressed this issue by using channel indentation and DIC microscopy techniques that provide visualisation of the matrix microstructural response across the regions of both direct and nondirect loading. We hypothesise that, by comparing the microstructural response following stress relaxation and creep compression, new insights can be revealed concerning the complex mechanisms of load bearing. Our results indicate that, with stress relaxation, the initial mode of stress decay appears to primarily involve relaxation of the surface layer. In the creep loading protocol, the main mode of stress release is a lateral distribution of load via the mid matrix. While these two modes of stress redistribution have a complex relationship with the zonally differentiated tissue microstructure and the depth of strain, four mechanostructural mechanisms are proposed to describe succinctly the load responses observed.

  13. Numerical investigation on residual stress distribution and evolution during multipass narrow gap welding of thick-walled stainless steel pipes

    International Nuclear Information System (INIS)

    Liu, C.; Zhang, J.X.; Xue, C.B.

    2011-01-01

    Research highlights: → We performed pass-by-pass simulation of stresses for welding of thick-walled pipes. → The distributions and evolution of the residual stresses are demonstrated. → After the groove is filled to a height, the through-wall stress is almost unchanged. - Abstracts: The detailed pass-by-pass finite element (FE) simulation is presented to investigate the residual stresses in narrow gap multipass welding of pipes with a wall thickness of 70 mm and 73 weld passes. The simulated residual stress on the outer surface is validated with the experimental one. The distribution and evolution of the through-wall residual stresses are demonstrated. The investigated results show that the residual stresses on the outer and inner surfaces are tensile in the weld zone and its vicinity. The through-wall axial residual stresses at the weld center line and the HAZ line demonstrate a distribution of bending type. The through-wall hoop residual stress within the weld is mostly tensile. After the groove is filled to a certain height, the peak tensile stresses and the stress distribution patterns for both axial and hoop stresses remain almost unchanged.

  14. Effect of preemptive weld overlay sequence on residual stress distribution for dissimilar metal weld of Kori nuclear power plant pressurizer

    Energy Technology Data Exchange (ETDEWEB)

    Bae, Hong Yeol; Song, Tae Kwang; Chun, Yun Bae; Oh, Chang Young; Kim, Yun Jae [Korea Univ., Seoul (Korea, Republic of); Lee, Kyoung Soo; Park, Chi Yong [Korea Electric Power Research Institute, Daejeon (Korea, Republic of)

    2008-07-01

    Weld overlay is one of the residual stress mitigation method which arrest crack. An overlay weld sued in this manner is termed a Preemptive Weld OverLay(PWOL). PWOL was good for distribution of residual stress of Dissimilar Metal Weld(DMW) by previous research. Because range of overlay welding is wide relatively, residual stress distribution on PWR is affected by welding sequence. In order to examine the effect of welding sequence, PWOL was applied to a specific DMW of KORI nuclear power plant by finite element analysis method. As a result, the welding direction that from nozzle to pipe is better good for residual stress distribution on PWR.

  15. Effect of preemptive weld overlay sequence on residual stress distribution for dissimilar metal weld of Kori nuclear power plant pressurizer

    International Nuclear Information System (INIS)

    Bae, Hong Yeol; Song, Tae Kwang; Chun, Yun Bae; Oh, Chang Young; Kim, Yun Jae; Lee, Kyoung Soo; Park, Chi Yong

    2008-01-01

    Weld overlay is one of the residual stress mitigation method which arrest crack. An overlay weld sued in this manner is termed a Preemptive Weld OverLay(PWOL). PWOL was good for distribution of residual stress of Dissimilar Metal Weld(DMW) by previous research. Because range of overlay welding is wide relatively, residual stress distribution on PWR is affected by welding sequence. In order to examine the effect of welding sequence, PWOL was applied to a specific DMW of KORI nuclear power plant by finite element analysis method. As a result, the welding direction that from nozzle to pipe is better good for residual stress distribution on PWR

  16. Forbearance coping, identification with heritage culture, acculturative stress, and psychological distress among Chinese international students.

    Science.gov (United States)

    Wei, Meifen; Liao, Kelly Yu-Hsin; Heppner, Puncky Paul; Chao, Ruth Chu-Lien; Ku, Tsun-Yao

    2012-01-01

    Based on Berry's (1997) theoretical framework for acculturation, our goal in this study was to examine whether the use of a culturally relevant coping strategy (i.e., forbearance coping, a predictor) would be associated with a lower level of psychological distress (a psychological outcome), for whom (i.e., those with weaker vs. stronger identification with heritage culture, a moderator), and under what situations (i.e., lower vs. higher acculturative stress, a moderator). A total of 188 Chinese international students completed an online survey. Results from a hierarchical regression indicated a significant 3-way interaction of forbearance coping, identification with heritage culture, and acculturative stress on psychological distress. For those with a weaker identification with their heritage culture, when acculturative stress was higher, the use of forbearance coping was positively associated with psychological distress. However, this was not the case when acculturative stress was lower. In other words, the use of forbearance coping was not significantly associated with psychological distress when acculturative stress was lower. Moreover, for those with a stronger cultural heritage identification, the use of forbearance coping was not significantly associated with psychological distress regardless of whether acculturative stress was high or low. Future research and implications are discussed. (c) 2012 APA, all rights reserved.

  17. A randomized controlled trial of mindfulness to reduce stress and burnout among intern medical practitioners.

    Science.gov (United States)

    Ireland, Michael J; Clough, Bonnie; Gill, Kim; Langan, Fleur; O'Connor, Angela; Spencer, Lyndall

    2017-04-01

    Stress and burnout are highly prevalent among medical doctors, and are associated with negative consequences for doctors, patients, and organizations. The purpose of the current study was to examine the effectiveness of a mindfulness training intervention in reducing stress and burnout among medical practitioners, by means of a Randomised Controlled Trial design. Participants were 44 intern doctors completing an emergency department rotation in a major Australian hospital. Participants were randomly assigned to either an active control (one hour extra break per week) or the 10-week mindfulness training intervention. Measures of stress and burnout were taken pre-, mid- and post intervention. Participants undergoing the 10-week mindfulness training program reported greater improvements in stress and burnout relative to participants in the control condition. Significant reduction in stress and burnout was observed for participants in the mindfulness condition. No such reductions were observed for participants in the control condition. Mindfulness interventions may provide medical practitioners with skills to effectively manage stress and burnout, thereby reducing their experience of these symptoms. It is likely that doctors would benefit from the inclusion of such a training program as a part of their general medical education.

  18. Effect of thermoplastic appliance thickness on initial stress distribution in periodontal ligament

    Directory of Open Access Journals (Sweden)

    De-Shin Liu

    2015-04-01

    Full Text Available A numerical investigation into the initial stress distribution induced within the periodontal ligament by thermoplastic appliances with different thicknesses is performed. Based on the plaster model of a 25-year-old male patient, a finite element model of the maxillary lateral incisors and their supporting structures is constructed. In addition, four finite element models of thermoplastic appliances with different thicknesses in the range of 0.5–1.25 mm are also constructed based on the same plaster model. Finite element analysis simulations are performed to examine the effects of the force delivered by the thermoplastic appliances on the stress response of the periodontal ligament during the elastic recovery process. The results show that the stress induced in the periodontal ligament increases with an increasing appliance thickness. For example, the stress triples from 0.0012 to 0.0038 MPa as the appliance thickness is increased from 0.75 to 1.25 mm. The results presented in this study provide a useful insight into as a result of the compressive and tensile stresses induced by thermoplastic appliances of different thicknesses. Moreover, the results enable the periodontal ligament stress levels produced by thermoplastic appliances of different thicknesses to be reliably estimated.

  19. Effect of cryogenic treatment on distribution of residual stress in case carburized En 353 steel

    International Nuclear Information System (INIS)

    Bensely, A.; Venkatesh, S.; Mohan Lal, D.; Nagarajan, G.; Rajadurai, A.; Junik, Krzysztof

    2008-01-01

    The effect of cryogenic treatment on the distribution of residual stress in the case carburized steel (En 353) was studied using X-ray diffraction technique. Two types of cryogenic treatment: shallow cryogenic treatment (193 K) and deep cryogenic treatment (77 K) were adopted, as a supplement to conventional heat treatment. The amount of retained austenite in conventionally heat-treated, shallow cryogenically treated and deep cryogenically treated samples was found to be 28%, 22% and 14%, respectively. The conventionally heat-treated, shallow cryogenically treated and deep cryogenically treated samples in untempered condition had a surface residual stress of -125 MPa, -115 MPa and -235 MPa, respectively. After tempering the conventionally heat-treated, shallow cryogenically treated and deep cryogenically treated samples had a surface residual stress of -150 MPa, -80 MPa and -80 MPa, respectively. A comparative study of the three treatments revealed that there was an increase in the compressive residual stress in steel that was subjected to cryogenic treatment prior to tempering. The experimental investigation revealed that deep cryogenically treated steel when subjected to tempering has undergone a reduction in compressive residual stress. Such stress relieving behaviour was mainly due to the increased precipitation of fine carbides in specimens subjected to DCT with tempering

  20. Dependence of ΔE effect on internal stresses in nickel: Experimental results by laser interferometry

    International Nuclear Information System (INIS)

    Chicharro, J.M.; Bayon, A.; Salazar, F.

    2006-01-01

    The speckle heterodyne interferometry is applied to the study of the dependence of Young's modulus on both the magnetic field and the internal stresses in a soft ferromagnetic material. Young's modulus is determined from the first natural longitudinal frequency of a slender magnetic rod positioned within a solenoid. Vibration of the sample is detected by an optical heterodyne system with a wide bandwidth. The samples are heated to above the Curie point and then cooled at several rates in order to induce different internal stresses. The study refers to nickel rods 10mm in diameter and 110mm in length. The grain sizes of the samples are also determined and related to changes in ΔE

  1. Dependence of {delta}E effect on internal stresses in nickel: Experimental results by laser interferometry

    Energy Technology Data Exchange (ETDEWEB)

    Chicharro, J.M. [Dept. de Mecanica Aplicada e Ingenieria de Proyectos, E.T.S.I. Industriales, Universidad de Castilla-La Mancha, Avd. Camilo Jose Cela s/n, 13071 Ciudad Real (Spain)]. E-mail: josemanuel.chicharro@uclm.es; Bayon, A. [Dept. de Fisica Aplicada a los Recursos Naturales, E.T.S.I. Minas, Universidad Politecnica de Madrid, c/Rios Rosas, 21, 28003 Madrid (Spain); Salazar, F. [Dept. de Fisica Aplicada a los Recursos Naturales, E.T.S.I. Minas, Universidad Politecnica de Madrid, c/Rios Rosas, 21, 28003 Madrid (Spain)

    2006-02-15

    The speckle heterodyne interferometry is applied to the study of the dependence of Young's modulus on both the magnetic field and the internal stresses in a soft ferromagnetic material. Young's modulus is determined from the first natural longitudinal frequency of a slender magnetic rod positioned within a solenoid. Vibration of the sample is detected by an optical heterodyne system with a wide bandwidth. The samples are heated to above the Curie point and then cooled at several rates in order to induce different internal stresses. The study refers to nickel rods 10mm in diameter and 110mm in length. The grain sizes of the samples are also determined and related to changes in {delta}E.

  2. Stress Corrosion Evaluation of Nitinol 60 for the International Space Station Water Recycling System

    Science.gov (United States)

    Torres, P. D.

    2016-01-01

    A stress corrosion cracking (SCC) evaluation of Nitinol 60 was performed because this alloy is considered a candidate bearing material for the Environmental Control and Life Support System (ECLSS), specifically in the Urine Processing Assembly of the International Space Station. An SCC evaluation that preceded this one during the 2013-2014 timeframe included various alloys: Inconel 625, Hastelloy C-276, titanium (Ti) commercially pure (CP), Ti 6Al-4V, extra-low interstitial (ELI) Ti 6Al-4V, and Cronidur 30. In that evaluation, most specimens were exposed for a year. The results of that evaluation were published in NASA/TM-2015-218206, entitled "Stress Corrosion Evaluation of Various Metallic Materials for the International Space Station Water Recycling System,"1 available at the NASA Scientific and Technical Information program web page: http://www.sti.nasa.gov. Nitinol 60 was added to the test program in 2014.

  3. Finite element simulations of internal stresses generated during the ferroelastic deformation of NiTi bodies

    International Nuclear Information System (INIS)

    Manach, P.Y.; Favier, D.; Rio, G.

    1996-01-01

    The aim of this paper is to analyse the generation of internal stresses during the predeformation of NiTi shape memory alloys in the martensitic state. This allows to determine the initial stress state in which the material will transform during the shape memory effect due to heating consecutively to this prestrain. In that way a three-dimensional finite element model of the deformation of shape memory alloys has been developed, the constitutive law being defined using an elastohysteresis tensor model. The influence of behavioural and geometrical factors are illustrated considering the numerical simulation of different cases of practical importance for industrial applications : the study of the bending behaviour of a NiTi cantilever beam as well as the study of the swelling of a pipe connection under both uniform and non uniform internal displacement fields. (orig.)

  4. Distribution of stress in greenhouses frames estimated by aerodynamic coefficients of Brazilian and European standards

    Directory of Open Access Journals (Sweden)

    José Gabriel Vieira Neto

    2016-04-01

    Full Text Available ABSTRACT Widely disseminated in both national and international scenarios, greenhouses are agribusiness solutions which are designed to allow for greater efficiency and control of the cultivation of plants. Bearing this in mind, the construction of greenhouses should take into consideration the incidence of wind, and other such aspects of comfort and safety, and ensure they are factored into the design of structural elements. In this study, we evaluated the effects of pressure coefficients established by the European standard EN 13031-1 (2001 and the Brazilian standard ABNT (1988, which are applicable to the structures of greenhouses with flat roofs, taking into account the following variables: roof slope, external and internal pressure coefficients and height-span ratio of the structure. Using the ANSYSTM computer program, zones of columns and roof were discretized by the Beam44 finite element to identify the maximum and minimum stress portions connected to the aerodynamic coefficients. With this analysis, we found that, in the smallest roof slope (a equal to 20°, the frame stress was quite similar for standards adopted. On the other hand, for the greatest inclination (a equal to 26°, the stress was consistently lower under the Brazilian standard. In view of this, we came to the conclusion that the differences between stresses when applying both standards were more significant at the higher degrees of height-span ratio and roof slope.

  5. The probability distribution of intergranular stress corrosion cracking life for sensitized 304 stainless steels in high temperature, high purity water

    International Nuclear Information System (INIS)

    Akashi, Masatsune; Kenjyo, Takao; Matsukura, Shinji; Kawamoto, Teruaki

    1984-01-01

    In order to discuss the probability distribution of intergranular stress corrsion carcking life for sensitized 304 stainless steels, a series of the creviced bent beem (CBB) and the uni-axial constant load tests were carried out in oxygenated high temperature, high purity water. The following concludions were resulted; (1) The initiation process of intergranular stress corrosion cracking has been assumed to be approximated by the Poisson stochastic process, based on the CBB test results. (2) The probability distribution of intergranular stress corrosion cracking life may consequently be approximated by the exponential probability distribution. (3) The experimental data could be fitted to the exponential probability distribution. (author)

  6. 1st International Symposium on Stress-Associated RNA Granules in Human Disease and Viral Infection

    Directory of Open Access Journals (Sweden)

    Bruce W. Banfield

    2014-09-01

    Full Text Available In recent years, important linkages have been made between RNA granules and human disease processes. On June 8-10 of this year, we hosted a new symposium, dubbed the 1st International Symposium on Stress-Associated RNA Granules in Human Disease and Viral Infection. This symposium brought together experts from diverse research disciplines ranging from cancer and neuroscience to infectious disease. This report summarizes speaker presentations and highlights current challenges in the field.

  7. Analysis of Effective and Internal Cyclic Stress Components in the Inconel Superalloy Fatigued at Elevated Temperature

    Czech Academy of Sciences Publication Activity Database

    Šmíd, Miroslav; Petrenec, Martin; Polák, Jaroslav; Obrtlík, Karel; Chlupová, Alice

    2011-01-01

    Roč. 278, 4 July (2011), s. 393-398 ISSN 1022-6680. [European Symposium on Superalloys and their Application. Wildbad Kreuth, 25.5.2010-28.5.2010] R&D Projects: GA ČR GA106/08/1631 Institutional research plan: CEZ:AV0Z20410507 Keywords : low cycle fatigue * superalloys * high temperature * hysteresis loop * effective and internal stresses Subject RIV: JL - Materials Fatigue, Friction Mechanics; JL - Materials Fatigue, Friction Mechanics (UFM-A)

  8. Dip-Test Internal Stress and the Composite Model of Creep Deformation

    Czech Academy of Sciences Publication Activity Database

    Dobeš, Ferdinand; Orlová, Alena

    2005-01-01

    Roč. 482, - (2005), s. 291-294 ISSN 0255-5476. [Materials Structure & Micromechanics of Fracture /4./. Brno, 23.06.2004-25.06.2004] R&D Pro jects: GA AV ČR(CZ) IAA2041202 Institutional research plan: CEZ:AV0Z20410507 Keywords : creep * internal stress * subgrain Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.399, year: 2005

  9. Stress and strain distribution in three different mini dental implant designs using in implant retained overdenture: a finite element analysis study

    Science.gov (United States)

    AUNMEUNGTONG, W.; KHONGKHUNTHIAN, P.; RUNGSIYAKULL, P.

    2016-01-01

    SUMMARY Finite Element Analysis (FEA) has been used for prediction of stress and strain between dental implant components and bone in the implant design process. Purpose Purpose of this study was to characterize and analyze stress and strain distribution occurring in bone and implants and to compare stress and strain of three different implant designs. Materials and methods Three different mini dental implant designs were included in this study: 1. a mini dental implant with an internal implant-abutment connection (MDIi); 2. a mini dental implant with an external implant-abutment connection (MDIe); 3. a single piece mini dental implant (MDIs). All implant designs were scanned using micro-CT scans. The imaging details of the implants were used to simulate models for FEA. An artificial bone volume of 9×9 mm in size was constructed and each implant was placed separately at the center of each bone model. All bone-implant models were simulatively loaded under an axial compressive force of 100 N and a 45-degree force of 100 N loading at the top of the implants using computer software to evaluate stress and strain distribution. Results There was no difference in stress or strain between the three implant designs. The stress and strain occurring in all three mini dental implant designs were mainly localized at the cortical bone around the bone-implant interface. Oblique 45° loading caused increased deformation, magnitude and distribution of stress and strain in all implant models. Conclusions Within the limits of this study, the average stress and strain in bone and implant models with MDIi were similar to those with MDIe and MDIs. The oblique 45° load played an important role in dramatically increased average stress and strain in all bone-implant models. Clinical implications Mini dental implants with external or internal connections have similar stress distribution to single piece mini dental implants. In clinical situations, the three types of mini dental implant

  10. Analysis of internal network requirements for the distributed Nordic Tier-1

    DEFF Research Database (Denmark)

    Behrmann, G.; Fischer, L.; Gamst, Mette

    2010-01-01

    The Tier-1 facility operated by the Nordic DataGrid Facility (NDGF) differs significantly from other Tier-1s in several aspects: It is not located at one or a few locations but instead distributed throughout the Nordic, it is not under the governance of a single organisation but but is instead...... build from resources under the control of a number of different national organisations. Being physically distributed makes the design and implementation of the networking infrastructure a challenge. NDGF has its own internal OPN connecting the sites participating in the distributed Tier-1. To assess...

  11. Deformation path effects on the internal stress development in cold worked austenitic steel deformed in tension

    International Nuclear Information System (INIS)

    Ahmed, I.I.; Grant, B.; Sherry, A.H.; Quinta da Fonseca, J.

    2014-01-01

    The effects of cold work level and strain paths on the flow stress of austenitic stainless steels, including Bauschinger effect and associated internal stresses were investigated with both mechanical testing and neutron diffraction techniques. The main objective was to assess the effects of cold rolling: to 5%, 10%, 20% and 40% reduction and uniaxial straining on the evolution of the internal strains during the re-straining to 5% tensile strain in-situ, which is relevant for stress corrosion cracking (SCC) studies. The results of mechanical testing showed that the yield strength of material increased when it was reloaded in the forward direction and decreased well below the flow stress when the loading direction was reversed, showing a strong Bauschinger effect. The magnitude of Bauschinger effect is independent on whether tensile or compressive prestraining comes first but rather on the amount of prestrain. The assessment of the effect of prestraining methods showed that the magnitude of yield asymmetry was higher in the material prestrained by uniaxial deformation than those prestrained by cold rolling. Neutron diffraction test results showed that the elastic lattice strain difference between the maximum and minimum strain values increased consistently with the applied stress during the re-straining to 5% tensile strain in-situ along the 3 orthogonal directions of the rolled plate. It also emerged that, following the in-situ loading of cold rolled materials to 5% tensile strain, the largest strain difference occurred in the material prestrained to 20% reduction. In cold rolled samples, the peak width increased with cold work levels and during re-straining to 5% along rolling, transverse to rolling and normal directions which simulated reversed condition. In contrast to the cold rolled samples, there was neither increase nor decrease in the peak width of samples prestrained by uniaxial deformation on re-straining in reverse direction. This was rationalised in

  12. TEMP-STRESS analysis of a reinforced concrete vessel under internal pressure

    International Nuclear Information System (INIS)

    Marchertas, A.H.; Kennedy, J.M.; Pfeiffer, P.A.

    1987-01-01

    The TEMP-STRESS FEM represents an axisymmetric simulation of the reinforced concrete vessel to internal pressurization. The information shows the global deformation, the state of strain/stress within the containment vessel with respect to the imposed pressures. Thus, the location and progress of concrete cracking, the stretching of the liner and the reinforcing bars and final failure are indicated through the entire loading range. Equilibrium of the entire system is assured at definite loading increments. With the progress of concrete cracking, the resisting load is continuously transferred to the reinforcing bars and the liner. Thus, after the tensile strength is exceeded and the concrete stress is set to zero, the internal pressures are entirely resisted by the liner and the reserve strength of the reinforcing bars. The reinforcing bars are mechanically connected to each other by splices, the ultimate strength of which is less than that of the rebars themselves. The corresponding strain at this limiting stress is lower than the ultimate strain of the liner. Therefore, the specified ultimate strength of the splices limits the pressurization of the vessel. Furthermore, once any of the splices fail, then load is transferred to the adjacent members, causing their failure and general failure of the vessel. (orig./HP)

  13. Adolescent internalizing symptoms and negative life events: the sensitizing effects of earlier life stress and cortisol.

    Science.gov (United States)

    Ruttle, Paula L; Armstrong, Jeffrey M; Klein, Marjorie H; Essex, Marilyn J

    2014-11-01

    Although adolescence is marked by increased negative life events and internalizing problems, few studies investigate this association as an ongoing longitudinal process. Moreover, while there are considerable individual differences in the degree to which these phenomena are linked, little is known about the origins of these differences. The present study examines early life stress (ELS) exposure and early-adolescent longitudinal afternoon cortisol level as predictors of the covariation between internalizing symptoms and negative life events across high school. ELS was assessed by maternal report during infancy, and the measure of cortisol was derived from assessments at ages 11, 13, and 15 years. Life events and internalizing symptoms were assessed at ages 15, 17, and 18 years. A two-level hierarchical linear model revealed that ELS and cortisol were independent predictors of the covariation of internalizing symptoms and negative life events. Compared to those with lower levels of ELS, ELS-exposed adolescents displayed tighter covariation between internalizing symptoms and negative life events. Adolescents with lower longitudinal afternoon cortisol displayed tighter covariation between negative life events and internalizing symptoms, while those with higher cortisol demonstrated weaker covariation, partially due to increased levels of internalizing symptoms when faced with fewer negative life events.

  14. Effect of process variables on the Drucker-Prager cap model and residual stress distribution of tablets estimated by the finite element method.

    Science.gov (United States)

    Hayashi, Yoshihiro; Otoguro, Saori; Miura, Takahiro; Onuki, Yoshinori; Obata, Yasuko; Takayama, Kozo

    2014-01-01

    A multivariate statistical technique was applied to clarify the causal correlation between variables in the manufacturing process and the residual stress distribution of tablets. Theophylline tablets were prepared according to a Box-Behnken design using the wet granulation method. Water amounts (X1), kneading time (X2), lubricant-mixing time (X3), and compression force (X4) were selected as design variables. The Drucker-Prager cap (DPC) model was selected as the method for modeling the mechanical behavior of pharmaceutical powders. Simulation parameters, such as Young's modulus, Poisson rate, internal friction angle, plastic deformation parameters, and initial density of the powder, were measured. Multiple regression analysis demonstrated that the simulation parameters were significantly affected by process variables. The constructed DPC models were fed into the analysis using the finite element method (FEM), and the mechanical behavior of pharmaceutical powders during the tableting process was analyzed using the FEM. The results of this analysis revealed that the residual stress distribution of tablets increased with increasing X4. Moreover, an interaction between X2 and X3 also had an effect on shear and the x-axial residual stress of tablets. Bayesian network analysis revealed causal relationships between the process variables, simulation parameters, residual stress distribution, and pharmaceutical responses of tablets. These results demonstrated the potential of the FEM as a tool to help improve our understanding of the residual stress of tablets and to optimize process variables, which not only affect tablet characteristics, but also are risks of causing tableting problems.

  15. Elevated temperature design of KALIMER reactor internals accounting for creep and stress-rupture effects

    International Nuclear Information System (INIS)

    Koo, Gyeong Hoi; Yoo, Bong

    2000-01-01

    In most LMFBR (Liquid Metal Fast Breed Reactor) design, the operating temperature is very high and the time-dependent creep and stress-rupture effects become so important in reactor structural design. Therefore, unlike with conventional PWR, the normal operating conditions can be basically dominant design loading because the hold time at elevated temperature condition is so long and enough to result in severe total creep ratcheting strains during total service lifetime. In this paper, elevated temperature design of the conceptually designed baffle annulus regions of KALIMER (Korea Advanced Liquid Metal Reactor) reactor internal structures is carried out for normal operating conditions which have the operating temperature 530 deg. C and the total service lifetime of 30 years. For the elevated temperature design of reactor internal structures, the ASME Code Case N-201-4 is used. Using this code, the time-dependent stress limits, the accumulated total inelastic strain during service lifetime, and the creep-fatigue damages are evaluated with the calculation results by the elastic analysis under conservative assumptions. The application procedures of elevated temperature design of the reactor internal structures using ASME code case N-201-4 with the elastic analysis method are described step by step in detail. This paper will be useful guide for actual application of elevated temperature design of various reactor types accounting for creep and stress-rupture effects. (author)

  16. Analysis of internal stress and anelasticity in the shock-compressed state from unloading wave data

    International Nuclear Information System (INIS)

    Johnson, J.N.; Lomdahl, P.S.; Wills, J.M.

    1991-01-01

    This paper reports on time resolved shock-wave measurements have often been used to infer microstructural behavior in crystalline solids. The authors apply this approach to an interpretation of the release-wave response of an aluminum alloy (6061-T6) as it is dynamically unloaded from a shock-compressed state of 20.7 GPa. The anelastic behavior in the initial portion of the unloading wave is attributed to the accumulation of internal stresses created by the shock process. Specific internal-stress models which are investigated are the double pile-up, the single pile-up, and single dislocation loops between pinning points. It is found that the essential characteristics of double and single pile-ups can be represented by a single dislocation between two pinned dislocations of like sing. Calculations of anelastic wave speeds at constant unloading strain rate are then compared with experimental data. The results suggest that the residual internal stress is due to pinned loops of density 10 15 M - 2 , and the viscous drag coefficient in the shock-compressed state is on the order of 10 - 7 MPa s (approximately two orders of magnitude greater than expected under ambient conditions)

  17. Theoretical Analysis of Stress Distribution in Bonded Single Strap and Stiffened Joints

    Directory of Open Access Journals (Sweden)

    Behnam Ghoddous

    Full Text Available Abstract In this paper, distribution of peeling stress in two types of adhesively-bonded joints is investigated. The joints are a single strap and a stiffened joint. Theses joints are under uniform tensile load and materials are assumed orthotropic. Layers can be identical or different in mechanical or geometrical properties. A two-dimensional elasticity theory that includes the complete stress-strain and the complete strain-displacement relations for adhesive and adherends is used in this analysis. The displacement is assumed to be linear in the adhesive layer. A set of differential equations was derived and solved by using appropriate boundary conditions. Results revealed that the peak peeling stress developed within the adhesive layer is a function of geometrical and mechanical properties. FEM solution is used as the second method to verify the analytical results. A good agreement is observed between analytical and FEM solutions.

  18. Comparing of Normal Stress Distribution in Static and Dynamic Soil-Structure Interaction Analyses

    International Nuclear Information System (INIS)

    Kholdebarin, Alireza; Massumi, Ali; Davoodi, Mohammad; Tabatabaiefar, Hamid Reza

    2008-01-01

    It is important to consider the vertical component of earthquake loading and inertia force in soil-structure interaction analyses. In most circumstances, design engineers are primarily concerned about the analysis of behavior of foundations subjected to earthquake-induced forces transmitted from the bedrock. In this research, a single rigid foundation with designated geometrical parameters located on sandy-clay soil has been modeled in FLAC software with Finite Different Method and subjected to three different vertical components of earthquake records. In these cases, it is important to evaluate effect of footing on underlying soil and to consider normal stress in soil with and without footing. The distribution of normal stress under the footing in static and dynamic states has been studied and compared. This Comparison indicated that, increasing in normal stress under the footing caused by vertical component of ground excitations, has decreased dynamic vertical settlement in comparison with static state

  19. Non--Local Approach to the Analysis of the Stress Distribution in Granular Systems.

    Science.gov (United States)

    Scott, J. E.; Kenkre, V. M.; Hurd, A. J.

    1998-03-01

    A continuum mechanical theory of the stress distribution in granular materials is presented, where the transformation of the vertical spatial coordinate into a formal time variable converts the study of the static stress distribution into a generally non--Markoffian, i.e., memory-possessing (non-local) propagation analysis. Previous treatments (J. -P). Bouchaud, M. E. Cates, and P. Claudin, J. Phys. I France 5, 639 (1995). (C. -h). Liu, S. R. Nagel, D. A. Schecter, S. N. Coppersmith, S. Majumdar, O. Narayan, and T. A. Witten, Science 269, 513 (1995). are shown to be particular cases of our theory corresponding to, respectively, wave-like and dif fusive limits of the general evolution. Calculations are presented for the example of ceramic or metal powder compaction in dies, with emphasis on the understanding of previously unexplained features as seen in experimental data found in the literature o ver the past 50 years. Specific proposals for new experimental investigations are presented.

  20. The Effect of Internal Salary Increment Distributions on Retention Behaviors of Western New York Teachers

    Science.gov (United States)

    Patterson, Michele M.

    2013-01-01

    This is a study of district internal salary distribution practices and its effect on retention. The study is a replication study as recommended by Jacobson (1986) and Lankford and Wyckoff (1997) whereby their research shows the prevalence of "back loading" and ineffectiveness relative to retention. In the case of this study, the…

  1. 76 FR 32231 - International Business Machines (IBM), Sales and Distribution Business Unit, Global Sales...

    Science.gov (United States)

    2011-06-03

    ... for the workers and former workers of International Business Machines (IBM), Sales and Distribution... reconsideration alleges that IBM outsourced to India and China. During the reconsideration investigation, it was..., Armonk, New York. The subject worker group supply computer software development and maintenance services...

  2. A distributed control algorithm for internal flow management in a multi-zone climate unit

    NARCIS (Netherlands)

    Persis, C. De; Jessen, J.J.; Izadi-Zamanabadi, R.; Schiøler, H.

    2008-01-01

    We examine a distributed control problem for internal flow management in a multi-zone climate unit. The problem consists of guaranteeing prescribed indoor climate conditions in a cascade connection of an arbitrarily large number of communicating zones, in which air masses are exchanged to redirect

  3. 76 FR 21033 - International Business Machines (IBM), Sales and Distribution Business Unit, Global Sales...

    Science.gov (United States)

    2011-04-14

    ... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-74,364] International Business Machines (IBM), Sales and Distribution Business Unit, Global Sales Solution Department, Off-Site Teleworker in Centerport, New York; Notice of Affirmative Determination Regarding Application for Reconsideration By application dated November 29, 2011,...

  4. Research on the internal pressure behavior of metal gas distribution pipelines with different types of tubing defects

    Directory of Open Access Journals (Sweden)

    Filip Stefan Mihai

    2017-01-01

    Full Text Available The paper aims to approach an important subject related to natural gas distribution networks which, depending on the expansion of the localities, are composed of intercommunicating pipes, pressure reducing stations and branch connections fittings. The urban networks are the most complex ones and the rural areas networks are the simplest. However, irrespective of their installation, they must meet the safety operating requirements as much as possible. According to standards, all these components must be tight and pressure resistant. In this regard, we intend to approach a very important issue related to the behavior of the tubular steel material showing corrosion and/or material defects, and to the internal stress caused by the gas pressure on the walls of the tubing material.

  5. Distinctive hippocampal zinc distribution patterns following stress exposure in an animal model of PTSD.

    Science.gov (United States)

    Sela, Hagit; Cohen, Hagit; Karpas, Zeev; Zeiri, Yehuda

    2017-03-22

    Emerging evidence suggests that zinc (Zn) deficiency is associated with depression and anxiety in both human and animal studies. The present study sought to assess whether there is an association between the magnitude of behavioral responses to stress and patterns of Zn distribution. The work has focused on one case study, the association between an animal model of posttraumatic stress disorder (PTSD) and the Zn distribution in the rat hippocampus. Behaviors were assessed with the elevated plus-maze and acoustic startle response tests 7 days later. Preset cut-off criteria classified exposed animals according to their individual behavioral responses. To further characterize the distribution of Zn that occurs in the hippocampus 8 days after the exposure, laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS) imaging was used. It has been found that Zn distribution in the dentate gyrus (DG) sub-region in the hippocampus is clearly more widely spread for rats that belong to the extreme behavioral response (EBR) group as compared to the control group. Comparison of the Zn concentration changes in the cornu ammonis 1 (CA1) and the DG sub-regions of the hippocampus shows that the concentration changes are statistically significantly higher in the EBR rats compared to the rats in the control and minimal behavioral response (MBR) groups. In order to understand the mechanism of stress-induced hippocampal Zn dyshomeostasis, relative quantitative analyses of metallothionein (MT), B-cell lymphoma 2 (Bcl-2) and caspase 3 immunoreactivity were performed. Significant differences in the number of caspase-ir and Bcl-2 cells were found in the hippocampal DG sub-region between the EBR group and the control and MBR groups. The results of this study demonstrate a statistically significant association between the degree of behavioral disruption resulting from stress exposure and the patterns of Zn distribution and concentration changes in the various hippocampal regions

  6. Correlates and predictors of parenting stress among internationally adopting mothers: A longitudinal investigation.

    Science.gov (United States)

    Viana, Andres G; Welsh, Janet A

    2010-07-01

    This study examined correlates and predictors of parenting stress among internationally adopting (IA) mothers with the goal of expanding the knowledge base on the experiences of adoptive parents. One hundred and forty-three IA mothers completed pre-adoption (Time 0) and six months post-adoption (Time 1) surveys with questions regarding child-, parent-, and family-related characteristics. Mother reports of higher depression symptoms, higher expectations of child developmental and behavioral/emotional problems, and a greater number of children in the family at pre-adoption were significantly related to higher parenting stress six months post-adoption. In contrast, mother reports of higher expectations for child acceptance and higher perceived social support at pre-adoption were significantly related to lower parenting stress six months post-adoption. Higher maternal depression symptoms, higher expectations of child behavior/emotional problems, and a greater number of children in the family at pre-adoption together accounted for 22% of the variance in parenting stress six months post-adoption. Concurrent higher maternal depression symptoms and higher reports of child behavioral/emotional problems predicted higher parenting stress six months post-adoption over and above pre-adoption predictors, and accounted for an additional 33% of the variance. Results and directions for future research are discussed from a transactional perspective, with particular emphasis on the importance of pre-adoptive information for adoption research and practice.

  7. Joining U.S. NRC international round robin for weld residual stress analysis. Stress analysis and validation in PWSCC mitigation program

    International Nuclear Information System (INIS)

    Maekawa, Akira; Serizawa, Hisashi; Murakawa, Hidekazu

    2012-01-01

    It is necessary to establish properly reliable weld residual stress analysis methods for accurate crack initiation and growth assessment of primary water stress corrosion cracking (PWSCC), which may occur in nickel-based dissimilar metal welds in pressurized water reactors. The U.S. Nuclear Regulatory Commission conducted an international round robin for weld residual stress analysis to improve stress analysis methods and to examine the uncertainties involved in the calculated stress values. In this paper, the results from the authors' participation in the round robin were reported. In the round robin, the weld residual stress in a nickel-based dissimilar metal weld of a pressurizer surge nozzle mock-up was computed under various analysis conditions. Based on these residual stress analysis results, a welding simulation code currently being developed that uses the iterative substructure method was validated and affecting factors on the analysis results were identified. (author)

  8. Effect of phytohormones on absorption and distribution of ions in salt-stressed bean plants

    Directory of Open Access Journals (Sweden)

    Zofia Starck

    2014-01-01

    Full Text Available Bean plant seedlings grown in water culture were treated for 5 days either with NaCl or with 7-times concentrated nutrient solution (diminished water potential by 3-103 hPa in both cases. Control and stressed plants were treated for 24 hrs with zeatin and GA,. NaCl-stress reduced distinctly ion absorption rate (K, Ca and P. Zeatin and GA3 promoted potassium uptake, but only in NaCI-treated plants. These hormones diminished Na accumulation in metabolically active organs but increased P- and Ca-content. In plants grown under both kind of stresses zeatin and GA3 partially reestablished the ratio of the main mono- to divalent cations, which increased in the leaves and apical part of the stressed plants. ABA introduced into the nutrient solution caused inhibition of the ion uptake (K, Ca, Mg and P. similar to that caused by NaCl-stress. The above reported results seem to confirm the supposition, that hormones act as an important factor contributing to regulation of both uptake and distribution of ions. In this way growth substances may also participate in the regulation of transport of various substances (among others - assimilates in the whole plant.

  9. Macroscopic electrical field distribution and field-induced surface stresses of needle-shaped field emitters

    Energy Technology Data Exchange (ETDEWEB)

    Moy, Charles K.S., E-mail: charles.moy@sydney.edu.au [Australian Centre for Microscopy and Microanalysis, The University of Sydney, Sydney, NSW 2006 (Australia); ARC Centre of Excellence for Design in Light Metals, The University of Sydney, Sydney, NSW 2006 (Australia); School of Civil Engineering, The University of Sydney, Sydney, NSW 2006 (Australia); Ranzi, Gianluca [ARC Centre of Excellence for Design in Light Metals, The University of Sydney, Sydney, NSW 2006 (Australia); School of Civil Engineering, The University of Sydney, Sydney, NSW 2006 (Australia); Petersen, Timothy C. [Australian Centre for Microscopy and Microanalysis, The University of Sydney, Sydney, NSW 2006 (Australia); Ringer, Simon P. [Australian Centre for Microscopy and Microanalysis, The University of Sydney, Sydney, NSW 2006 (Australia); ARC Centre of Excellence for Design in Light Metals, The University of Sydney, Sydney, NSW 2006 (Australia)

    2011-05-15

    One major concern since the development of the field ion microscope is the mechanical strength of the specimens. The macroscopic shape of the imaging tip greatly influences field-induced stresses and there is merit in further study of this phenomenon from a classical perspective. Understanding the geometrical, as opposed to localized electronic, factors that affect the stress might improve the quality and success rate of atom probe experiments. This study uses macroscopic electrostatic principles and finite element modelling to investigate field-induced stresses in relation to the shape of the tip. Three two-dimensional idealized models are considered, namely hyperbolic, parabolic and sphere-on-orthogonal-cone; the shapes of which are compared to experimental tips prepared by electro-polishing. Three dimensional morphologies of both a nano-porous and single-crystal aluminium tip are measured using electron tomography to quantitatively test the assumption of cylindrical symmetry for electro-polished tips. The porous tip was prepared and studied to demonstrate a fragile specimen for which such finite element studies could determine potential mechanical failure, prior to any exhaustive atom probe investigation. -- Research highlights: {yields} We use electrostatic principles and finite element to model field-induced stresses. {yields} We study two-dimensional idealized needle-shaped field emitters. {yields} Stress distribution of hyperbolic, parabolic and sphere-on-orthogonal-cone tips mapped. {yields} Electron tomography to obtain the morphology of three-dimensional aluminium tips. {yields} Studies of the morphology of the porous tip demonstrate a fragile specimen.

  10. The effect of unerupted permanent tooth crowns on the distribution of masticatory stress in children.

    Directory of Open Access Journals (Sweden)

    Ashley S Hammond

    Full Text Available Human mothers wean their children from breast milk at an earlier developmental stage than do ape mothers, resulting in human children chewing solid and semi-solid foods using the deciduous dentition. Mechanical forces generated by chewing solid foods during the post-weaning period travel through not only the deciduous teeth, but also the enamel caps of the developing permanent teeth within the maxilla and mandible, which are not present in the adult face. The effects of mechanical stress propagating through these very stiff structures have yet to be examined. Based on a heuristic model, we predicted that the enamel of the embedded developing teeth would act to reduce stresses in the surrounding bony elements of the juvenile face. We tested this hypothesis by simulating occlusal loading in a finite element (FE model of a child's cranium with a complete set of deciduous teeth and the first permanent molars embedded in the bony crypt in the maxilla. We modeled bone and enamel with appropriate material properties and assessed the effect of embedding high-stiffness enamel structures on stress distribution in the juvenile face. Against expectation, the presence of unerupted enamel caps does not affect the magnitude or location of stresses in the juvenile face. Our results do not support the hypothesis that the unerupted secondary teeth act to moderate stresses in the juvenile face.

  11. Calorimetric features of release of plastic deformation induced internal stresses, and approach to equilibrium state on annealing of crystals and glasses

    Energy Technology Data Exchange (ETDEWEB)

    Johari, G.P., E-mail: joharig@mcmaster.ca

    2014-04-01

    Highlights: • Stress release in a glass occurs at a faster rate than structural relaxation. • Plastically-deformed glass would show two exothermic minima, and no glass transition. • Enthalpy matching procedure would yield an inaccurate fictive temperature. • Complex heat capacity may distinguish plastically-deformed from quench-formed glass. - Abstract: Plastic deformation of crystals and glasses produces internal strains (stresses), which change their energy and other thermodynamic properties. On annealing, these stresses decrease at a rate faster than the structure relaxes toward the equilibrium state. Mechanism of such relaxations in crystals differs from that in glasses and it also differs for glasses of different types. In all cases, the energy related properties decrease with time isothermally and on heating, resembling the structure relaxation of a stress-free glass. We consider these features and argue that kinetics of enthalpy loss with time yields the rate constants of the stress release and of the structure change, and not the viscosity determining α-relaxation time. Since thermal cycling does not recover the enthalpy from internal stresses, a glass with stresses has neither a glass-softening temperature, T{sub g}, nor a fictive temperature, T{sub f}. Plastic deformation would not rejuvenate a physically aged glass to the properties of its un-aged state. The Prigogine–Defay ratio can be extended to all T{sub f}s, and used to investigate the effect of distribution of relaxation times on its value, but it can not be defined for an internally stressed glass. After discussing the effects of annealing on the heat capacity and DSC scans, we conclude that on slow heating, glass with deformation-induced stresses would show two exothermic minima, and normal glass would show only one such minimum. Temperature-modulated scanning calorimetry would also distinguish an internally stressed glass from an equally high-enthalpy, stress-free glass. Enthalpy

  12. Numerical simulation of stress distribution in Al2 O3-TiC/Q235 diffusion bonded joints

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    The distributions of the axial stress and shear stress in Al2O3-TiC/Q235 diffusion bonded joints were studied using finite element method (FEM). The effect of interlayer thickness on the axial stress and shear stress was also investigated. The results indicate that the gradients of the axial stress and shear stress are great near the joint edge. The maximal shear stress produces at the interface of the Al2O3-TiC and Ti interlayer. With the increase of Cu interlayer thickness, the magnitudes of the axial stress and shear stress first decrease and then increase. The distribution of the axial stress changes greatly with a little change in the shear stress. The shear fracture initiates at the interface of the Al2O3-TiC/ Ti interlayer with high shear stress and then propagates to the Al2O3-TiC side, which is consistent with the stress FEM calculating results.

  13. Distribution of stress on TMJ disc induced by use of chincup therapy: assessment by the finite element method

    Science.gov (United States)

    Calçada, Flávio Siqueira; Guimarães, Antônio Sérgio; Teixeira, Marcelo Lucchesi; Takamatsu, Flávio Atsushi

    2017-01-01

    ABSTRACT Objective: To assess the distribution of stress produced on TMJ disc by chincup therapy, by means of the finite element method. Methods: a simplified three-dimensional TMJ disc model was developed by using Rhinoceros 3D software, and exported to ANSYS software. A 4.9N load was applied on the inferior surface of the model at inclinations of 30, 40, and 50 degrees to the mandibular plane (GoMe). ANSYS was used to analyze stress distribution on the TMJ disc for the different angulations, by means of finite element method. Results: The results showed that the tensile and compressive stresses concentrations were higher on the inferior surface of the model. More presence of tensile stress was found in the middle-anterior region of the model and its location was not altered in the three directions of load application. There was more presence of compressive stress in the middle and mid-posterior regions, but when a 50o inclined load was applied, concentration in the middle region was prevalent. Tensile and compressive stresses intensities progressively diminished as the load was more vertically applied. Conclusions: stress induced by the chincup therapy is mainly located on the inferior surface of the model. Loads at greater angles to the mandibular plane produced distribution of stresses with lower intensity and a concentration of compressive stresses in the middle region. The simplified three-dimensional model proved useful for assessing the distribution of stresses on the TMJ disc induced by the chincup therapy. PMID:29160348

  14. On the calculation of internal forces in mechanically stressed polyatomic molecules

    International Nuclear Information System (INIS)

    Avdoshenko, Stanislav M.; Konda, Sai Sriharsha M.; Makarov, Dmitrii E.

    2014-01-01

    We discuss how to define and to compute internal forces in a molecule subjected to mechanical stress. Because of the inherently many-body character of intramolecular interactions, internal forces cannot be uniquely defined without specifying a set of internal coordinates used to describe the molecular structure. When such a set is comprised of 3N − 6 interactomic distances (N being the number of atoms) and includes the bond lengths of interest, we show that the associated forces, while satisfying the equation F = ∂V/∂R (where R is the bond length, F is the internal force in this bond, and V is the potential energy of the molecule), can be determined from the molecular geometry alone. We illustrate these ideas using several toy models ranging from small molecules to a graphene sheet and show that the magnitude of the internal force in a bond is not necessarily a good predictor of its strength in response to mechanical loading. At the same time, analysis of internal forces reveals interesting phenomena such as the force multiplication effect, where weak external forces may, e.g., be used to break strong bonds, and offers insight into the catch-bond phenomenon where chemical reactivity is suppressed through application of a force

  15. X-ray evaluation of residual stress distributions within surface machined layer generated by surface machining and sequential welding

    International Nuclear Information System (INIS)

    Taniguchi, Yuu; Okano, Shigetaka; Mochizuki, Masahito

    2017-01-01

    The excessive tensile residual stress generated by welding after surface machining may be an important factor to cause stress corrosion cracking (SCC) in nuclear power plants. Therefore we need to understand and control the residual stress distribution appropriately. In this study, residual stress distributions within surface machined layer generated by surface machining and sequential welding were evaluated by X-ray diffraction method. Depth directional distributions were also investigated by electrolytic polishing. In addition, to consider the effect of work hardened layer on the residual stress distributions, we also measured full width at half maximum (FWHM) obtained from X-ray diffraction. Testing material was a low-carbon austenitic stainless steel type SUS316L. Test specimens were prepared by surface machining with different cutting conditions. Then, bead-on-plate welding under the same welding condition was carried out on the test specimens with different surface machined layer. As a result, the tensile residual stress generated by surface machining increased with increasing cutting speed and showed nearly uniform distributions on the surface. Furthermore, the tensile residual stress drastically decreased with increasing measurement depth within surface machined layer. Then, the residual stress approached 0 MPa after the compressive value showed. FWHM also decreased drastically with increasing measurement depth and almost constant value from a certain depth, which was almost equal regardless of the machining condition, within surface machined layer in all specimens. After welding, the transverse distribution of the longitudinal residual stress varied in the area apart from the weld center according to machining conditions and had a maximum value in heat affected zone. The magnitude of the maximum residual stress was almost equal regardless of the machining condition and decreased with increasing measurement depth within surface machined layer. Finally, the

  16. Relationship between occupational stress and depressive mood among interns and residents in a tertiary hospital, Seoul, Korea.

    Science.gov (United States)

    Kim, Keon; Lee, Sunhwa; Choi, Yoon Hee

    2015-06-01

    Occupational stress can have a harmful effect on the individual both physically and psychologically. In Korea, occupational stress of physician is rarely demonstrated. Although it is well reported that physicians tend to have a high incidence of minor psychiatric disorders, the magnitude of the problem remains unclear. Interns and residents are thought to be under substantial amount of stress, and tend to have psychiatric disorder. In this paper, we aimed to evaluate the relationship between the occupational stress and depression of residents. The participants of this study were surgical and medical residents in a tertiary hospital in Korea. For measurement of occupational stress, we used an occupational stress scale. In addition, to evaluate the prevalence of depression, we used the Beck Depression Inventory. Female doctors showed higher degree of occupational stress than the males. The interns and chief residents showed higher degree of occupational stress than the other residents. Interestingly, in this study, most of the participants experienced a depressive mood. Compared with the general population, job demand and culture of workplace were high. Occupational stress was the only significant predictor of a depressive mood. Hospital residents experience a high degree of occupational stress leading to a depressed mood due to various risk factors. Therefore, it is essential to recognize the occupational stress of residents early, to encourage positive competition and peer and social support, and to help improve the residents' ability to cope with stress.

  17. Stress distribution in the 16MND5 bainitic steel. Experimental analysis and polycrystalline modelling

    International Nuclear Information System (INIS)

    Pesci, R.; Inal, K.; Berveiller, M.; Masson, R.

    2003-01-01

    The 16MND5 bainitic steel being a two-phase material (ferrite/cementite), the X-Ray Diffraction (XRD) is the most efficient tool to determine the stress states into the ferritic phase (sin 2 ψ method). The latter, coupled to the observations realized during tensile tests (specimen surface and facies), have permitted to establish criteria to describe the behavior and the damaging processes of the material on a crystallographic scale, in the lower part of the ductile-to-brittle transition region and at lower temperatures [-196 deg. C;-60 deg. C]. During the loading, the damage is observed with a Scanning Electron Microscope, while the internal stresses are determined by XRD: the stress states are less important in ferrite than in bainite (macroscopic stress), the difference not exceeding 150 MPa. A multi-scale polycrystalline model is developed concurrently with the experimental measurements: a Mori-Tanaka formulation is used to describe the elastoplastic behavior of a ferritic single crystal reinforced by cementite precipitates, while the transition to the polycrystal is achieved by a self-consistent approach. The developed modeling takes into account the temperature effects on the stress states in each phase and includes a cleavage criterion (critical value of the stress normal to [100] planes), which expresses the damage of the material: thus, it enables to predict the actual experimental behavior of the 16MND5 steel in relation to temperature, and to take into account the failure process which is fragile from -120 deg. C. Besides, it is also possible to calculate the strains of the diffracting planes, which can be compared to those measured by XRD: this enables to evaluate the heterogeneity of the strains for each crystallographic orientation. (authors)

  18. Growth recovery in newly arrived international adoptees in Italy: relation to parenting stress.

    Science.gov (United States)

    Canzi, Elena; Rosnati, Rosa; Miller, Laurie C

    2018-04-12

    Following initial adversities, most internationally adopted children arrive with significant growth delays. Post-placement recovery has been widely documented, but research about risk or protective factors is still limited. Even less is known about the relationship between growth recovery and the quality of the family environment. 28 children in 26 adoptive families were involved in this longitudinal study. A comprehensive evaluation (including anthropometry, cognitive assessment [using the Leiter International Performance Scale-Revised], and completion by both parents of the Parenting Stress Index - Short Form) was done at arrival of the child, and 1 year later. Results evidenced that on arrival nearly half of children had growth measurements in the normal range. All the children showed a significant recovery in height and weight at 6 and 12 months post-placement. Initial and follow up growth measurements correlated strongly. Growth recovery was related to the age of the child at adoption, the proportion of time the child had resided in institutional care, as well as parenting stress. Results suggested that the higher the parenting stress experienced the less improvements occurred in children: for mothers for height and weight, for fathers for all the growth indicators. Results suggested the critical importance of family factor in influencing children's growth recovery.

  19. Consensus statement update on posttraumatic stress disorder from the international consensus group on depression and anxiety.

    Science.gov (United States)

    Ballenger, James C; Davidson, Jonathan R T; Lecrubier, Yves; Nutt, David J; Marshall, Randall D; Nemeroff, Charles B; Shalev, Arieh Y; Yehuda, Rachel

    2004-01-01

    To provide an update to the "Consensus Statement on Posttraumatic Stress Disorder From the International Consensus Group on Depression and Anxiety" that was published in a supplement to The Journal of Clinical Psychiatry (2000) by presenting important developments in the field, the latest recommendations for patient care, and suggestions for future research. The 4 members of the International Consensus Group on Depression and Anxiety were James C. Ballenger (chair), Jonathan R. T. Davidson, Yves Lecrubier, and David J. Nutt. Other faculty who were invited by the chair were Randall D. Marshall, Charles B. Nemeroff, Arieh Y. Shalev, and Rachel Yehuda. The consensus statement is based on the 7 review articles in this supplement and the related scientific literature. Group meetings were held over a 2-day period. On day 1, the group discussed topics to be represented by the 7 review articles in this supplement, and the chair identified key issues for further debate. On day 2, the group discussed these issues to arrive at a consensus view. After the group meetings, the consensus statement was drafted by the chair and approved by all faculty. There have been advancements in the science and treatment of posttraumatic stress disorder. Attention to this disorder has increased with recent world events; however, continued efforts are needed to improve diagnosis, treatment, and prevention of posttraumatic stress disorder.

  20. Predicting Posttraumatic Stress Symptom Prevalence and Local Distribution after an Earthquake with Scarce Data.

    Science.gov (United States)

    Dussaillant, Francisca; Apablaza, Mauricio

    2017-08-01

    After a major earthquake, the assignment of scarce mental health emergency personnel to different geographic areas is crucial to the effective management of the crisis. The scarce information that is available in the aftermath of a disaster may be valuable in helping predict where are the populations that are in most need. The objectives of this study were to derive algorithms to predict posttraumatic stress (PTS) symptom prevalence and local distribution after an earthquake and to test whether there are algorithms that require few input data and are still reasonably predictive. A rich database of PTS symptoms, informed after Chile's 2010 earthquake and tsunami, was used. Several model specifications for the mean and centiles of the distribution of PTS symptoms, together with posttraumatic stress disorder (PTSD) prevalence, were estimated via linear and quantile regressions. The models varied in the set of covariates included. Adjusted R2 for the most liberal specifications (in terms of numbers of covariates included) ranged from 0.62 to 0.74, depending on the outcome. When only including peak ground acceleration (PGA), poverty rate, and household damage in linear and quadratic form, predictive capacity was still good (adjusted R2 from 0.59 to 0.67 were obtained). Information about local poverty, household damage, and PGA can be used as an aid to predict PTS symptom prevalence and local distribution after an earthquake. This can be of help to improve the assignment of mental health personnel to the affected localities. Dussaillant F , Apablaza M . Predicting posttraumatic stress symptom prevalence and local distribution after an earthquake with scarce data. Prehosp Disaster Med. 2017;32(4):357-367.

  1. ABA pretreatment can alter the distribution of polysomes in salt-stressed barley sprouts

    Directory of Open Access Journals (Sweden)

    Szypulska Ewa

    2016-12-01

    Full Text Available The study analyzed caryopses of barley (Hordeum vulgare cv. Stratus. Caryopses were germinated in darkness at 20°C in three experimental setups: (a in distilled water for 24 hours, followed by 100 mM NaCl for another 24 hours (salinity stress, SS, (b in 100 μM of abscisic acid for the first 24 hours, followed by rinsing with distilled water to remove residual ABA, and in 100 mM NaCl for another 24 hours (ABA pretreatment + salinity stress, ABAS, (c in distilled water only (control, C. Changes in the content of free polysomes (FP, membrane-bound polysomes (MBP, cytoskeleton-bound polysomes (CBP and cytomatrix-bound polysomes (CMBP were examined in barley sprouts germinated in SS and ABAS treatments for 48 hours. In salt-stressed barley sprouts, the concentrations of membrane-bound and cytoskeleton-bound polysomes (MBP, CBP and CMBP decreased significantly, whereas an increase was noted only in the free polysome (FP fraction. ABA pretreatment altered the distribution of polysomes in stressed plants. The content of cytoskeletonbound polysomes (CBP and CMBP increased, FP levels decreased, whereas no changes in MBP content were observed in response to ABA treatment. Our results suggest that plants respond to salt stress by increasing the concentrations of free polysomes that are probably released from damaged cell structures, mainly membranes. Our present and previous findings indicate that ABA could inhibit the release of FP in stressed plants by enhancing polysome binding to the cytoskeleton.

  2. [Influence of different designs of marginal preparation on stress distribution in the mandibular premolar restored with endocrown].

    Science.gov (United States)

    Guo, Jing; Wang, Xiao-Yu; Li, Xue-Sheng; Sun, Hai-Yang; Liu, Lin; Li, Hong-Bo

    2016-02-01

    To evaluate the effect of different designs of marginal preparation on stress distribution in the mandibular premolar restored with endocrown using three-dimensional finite element method. Four models with different designs of marginal preparation, including the flat margin, 90° shoulder, 135° shoulder and chamfer shoulder, were established to imitate mandibular first premolar restored with endocrown. A load of 100 N was applied to the intersection of the long axis and the occlusal surface, either parallel or with an angle of 45° to the long axis of the tooth. The maximum values of Von Mises stress and the stress distribution around the cervical region of the abutment and the endocrown with different designs of marginal preparation were analyzed. The load parallel to the long axis of the tooth caused obvious stress concentration in the lingual portions of both the cervical region of the tooth tissue and the restoration. The stress distribution characteristics on the cervical region of the models with a flat margin and a 90° shoulder were more uniform than those in the models with a 135° shoulder and chamfer shoulder. Loading at 45° to the long axis caused stress concentration mainly on the buccal portion of the cervical region, and the model with a flat margin showed the most favorable stress distribution patterns with a greater maximum Von Mises stress under this circumstance than that with a parallel loading. Irrespective of the loading direction, the stress value was the lowest in the flat margin model, where the stress value in the cervical region of the endocrown was greater than that in the counterpart of the tooth tissue. The stress level on the enamel was higher than that on the dentin nearby in the flat margin model. From the stress distribution point of view, endocrowns with flat margin followed by a 90° shoulder are recommended.

  3. Waiting time distribution revealing the internal spin dynamics in a double quantum dot

    Science.gov (United States)

    Ptaszyński, Krzysztof

    2017-07-01

    Waiting time distribution and the zero-frequency full counting statistics of unidirectional electron transport through a double quantum dot molecule attached to spin-polarized leads are analyzed using the quantum master equation. The waiting time distribution exhibits a nontrivial dependence on the value of the exchange coupling between the dots and the gradient of the applied magnetic field, which reveals the oscillations between the spin states of the molecule. The zero-frequency full counting statistics, on the other hand, is independent of the aforementioned quantities, thus giving no insight into the internal dynamics. The fact that the waiting time distribution and the zero-frequency full counting statistics give a nonequivalent information is associated with two factors. Firstly, it can be explained by the sensitivity to different timescales of the dynamics of the system. Secondly, it is associated with the presence of the correlation between subsequent waiting times, which makes the renewal theory, relating the full counting statistics and the waiting time distribution, no longer applicable. The study highlights the particular usefulness of the waiting time distribution for the analysis of the internal dynamics of mesoscopic systems.

  4. A new coal-permeability model: Internal swelling stress and fracture-matrix interaction

    Energy Technology Data Exchange (ETDEWEB)

    Liu, H.H.; Rutqvist, J.

    2009-10-01

    We have developed a new coal-permeability model for uniaxial strain and constant confining stress conditions. The model is unique in that it explicitly considers fracture-matrix interaction during coal deformation processes and is based on a newly proposed internal-swelling stress concept. This concept is used to account for the impact of matrix swelling (or shrinkage) on fracture-aperture changes resulting from partial separation of matrix blocks by fractures that do not completely cut through the whole matrix. The proposed permeability model is evaluated with data from three Valencia Canyon coalbed wells in the San Juan Basin, where increased permeability has been observed during CH{sub 4} gas production, as well as with published data from laboratory tests. Model results are generally in good agreement with observed permeability changes. The importance of fracture-matrix interaction in determining coal permeability, demonstrated in this work using relatively simple stress conditions, underscores the need for a dual-continuum (fracture and matrix) mechanical approach to rigorously capture coal-deformation processes under complex stress conditions, as well as the coupled flow and transport processes in coal seams.

  5. Initial Characterization of Internal Medicine Resident Resilience and Association with Stress and Burnout

    Directory of Open Access Journals (Sweden)

    Amber-Nicole Bird

    2016-01-01

    Full Text Available Introduction. Burnout is prevalent in medical trainees. Little data exists on resident resilience. Methods. Anonymous surveys were provided to a convenience sample of internal medicine residents. Resilience was assessed using the Connor-Davidson resilience scale. Responses were categorized into low (<70, intermediate (70–79, and high (80–100 resilience. Results. 77 residents from six institutions completed surveys. 26% of residents had high resilience, 43% intermediate, and 31% low. The mean resilience score was 73.6±9.6 and lower than the general population (mean 80.4±12.5, p<0.001. Trainees with high resilience were more likely to never have stress interfere with their relationships outside of work (high: 40%; low: 0%; p<0.001. High resilience residents were more likely to have the skills to manage stress and burnout (high: 80%; low: 46%; p=0.02 and less likely to feel inferior to peers (high: 20.0%; low: 70.8%; p<0.001. There was a trend towards those with high resilience reporting less burnout (high: 40.0%; intermediate: 27%; low: 16.7%; p=0.08. Only 60% report a program outlet to discuss burnout. Conclusions. There is a wide range of resilience among IM residents and scores were lower than the general population. Low resilience is associated with more stress interfering with relationships, feeling inferior to peers, and fewer skills to manage stress and burnout.

  6. Axial contraction in etched optical fiber due to internal stress reduction.

    Science.gov (United States)

    Lim, Kok-Sing; Yang, Hang-Zhou; Chong, Wu-Yi; Cheong, Yew-Ken; Lim, Chin-Hong; Ali, Norfizah M; Ahmad, Harith

    2013-02-11

    When an optical fiber is dipped in an etching solution, the internal stress profile in the fiber varies with the fiber diameter. We observed a physical contraction as much as 0.2% in the fiber axial dimension when the fiber was reduced from its original diameter to ~6 µm through analysis using high resolution microscope images of the grating period of an etched FBG at different fiber diameters. This axial contraction is related to the varying axial stress profile in the fiber when the fiber diameter is reduced. On top of that, the refractive index of fiber core increases with reducing fiber diameter due to stress-optic effect. The calculated index increment is as much as 1.8 × 10(-3) at the center of fiber core after the diameter is reduced down to ~6 µm. In comparison with the conventional model that assumes constant grating period and neglects the variation in stress-induced index change in fiber core, our proposed model indicates a discrepancy as much as 3nm in Bragg wavelength at a fiber diameter of ~6 µm.

  7. Effects of heat stress on dynamic absorption process, tissue distribution and utilization efficiency of vitamin C in broilers

    International Nuclear Information System (INIS)

    Liu Guohua; Chen Guosheng; Cai Huiyi

    1998-01-01

    The experiment was conducted to determine the effects of heat stress on ascorbic acid nutritional physiology of broilers with radioisotope technology. 3 H-Vc was fed to broilers and then the blood, liver, kidney, breast muscle, and excreta were sampled to determine the dynamic absorption process, the tissue distribution and the utilization efficiency of vitamin C. The results indicated that the absorption, metabolism and mobilization of supplemented vitamin C in broilers with heat stress was faster than that in broilers without heat stress. However, the utilization efficiency of supplemented vitamin C in broilers with heat stress was not higher than that of broilers without heat stress

  8. Temperature-time distribution and thermal stresses on the RTG fins and shell during water cooling

    Science.gov (United States)

    Turner, R. H.

    1983-01-01

    Radioisotope thermoelectric generator (RTG) packages designed for space missions generally do not require active cooling. However, the heat they generate cannot remain inside of the launch vehicle bay and requires active removal. Therefore, before the Shuttle bay door is closed, the RTG coolant tubes attached to the heat rejection fins must be filled with water, which will circulate and remove most of the heat from the cargo bay. There is concern that charging a system at initial temperature around 200 C with water at 24 C can cause unacceptable thermal stresses in the RTG shell and fins. A computer model is developed to estimate the transient temperature distribution resulting from such charging. The thermal stresses resulting from the temperature gradients do not exceed the elastic deformation limit for the material. Since the simplified mathematical model for thermal stresses tends to overestimate stresses, it is concluded that the RTG can be cooled by introducing water at 24 C to the initially hot fin coolant tubes while the RTG is in the Shuttle cargo bay.

  9. Effects of Abiotic and Biotic Stresses on the Internalization and Dissemination of Human Norovirus Surrogates in Growing Romaine Lettuce.

    Science.gov (United States)

    DiCaprio, Erin; Purgianto, Anastasia; Li, Jianrong

    2015-07-01

    Human norovirus (NoV) is the major causative agent of fresh-produce-related outbreaks of gastroenteritis; however, the ecology and persistence of human NoV in produce systems are poorly understood. In this study, the effects of abiotic and biotic stresses on the internalization and dissemination of two human NoV surrogates (murine norovirus 1 [MNV-1] and Tulane virus [TV]) in romaine lettuce were determined. To induce abiotic stress, romaine lettuce was grown under drought and flood conditions that mimic extreme weather events, followed by inoculation of soil with MNV-1 or TV. Independently, lettuce plants were infected with lettuce mosaic virus (LMV) to induce biotic stress, followed by inoculation with TV. Plants were grown for 14 days, and viral titers in harvested tissues were determined by plaque assays. It was found that drought stress significantly decreased the rates of both MNV-1 and TV internalization and dissemination. In contrast, neither flood stress nor biotic stress significantly impacted viral internalization or dissemination. Additionally, the rates of TV internalization and dissemination in soil-grown lettuce were significantly higher than those for MNV-1. Collectively, these results demonstrated that (i) human NoV surrogates can be internalized via roots and disseminated to shoots and leaves of romaine lettuce grown in soil, (ii) abiotic stress (drought) but not biotic stress (LMV infection) affects the rates of viral internalization and dissemination, and (iii) the type of virus affects the efficiency of internalization and dissemination. This study also highlights the need to develop effective measures to eliminate internalized viruses in fresh produce. Copyright © 2015, American Society for Microbiology. All Rights Reserved.

  10. The Effect of Perfectionism and Acculturative Stress on Levels of Depression Experienced by East Asian International Students

    Science.gov (United States)

    Hamamura, Toshitaka; Laird, Philip G.

    2014-01-01

    This study examined relationships among acculturative stress, grade point average satisfaction, maladaptive perfectionism, and depression in 52 East Asian international students and 126 North American students. Results indicated that a combined effect of perfectionism and acculturative stress accounted for more than 30% of the variance related to…

  11. Constraints on Stress Components at the Internal Singular Point of an Elastic Compound Structure

    Science.gov (United States)

    Pestrenin, V. M.; Pestrenina, I. V.

    2017-03-01

    The classical analytical and numerical methods for investigating the stress-strain state (SSS) in the vicinity of a singular point consider the point as a mathematical one (having no linear dimensions). The reliability of the solution obtained by such methods is valid only outside a small vicinity of the singular point, because the macroscopic equations become incorrect and microscopic ones have to be used to describe the SSS in this vicinity. Also, it is impossible to set constraint or to formulate solutions in stress-strain terms for a mathematical point. These problems do not arise if the singular point is identified with the representative volume of material of the structure studied. In authors' opinion, this approach is consistent with the postulates of continuum mechanics. In this case, the formulation of constraints at a singular point and their investigation becomes an independent problem of mechanics for bodies with singularities. This method was used to explore constraints at an internal singular point (representative volume) of a compound wedge and a compound rib. It is shown that, in addition to the constraints given in the classical approach, there are also constraints depending on the macroscopic parameters of constituent materials. These constraints turn the problems of deformable bodies with an internal singular point into nonclassical ones. Combinations of material parameters determine the number of additional constraints and the critical stress state at the singular point. Results of this research can be used in the mechanics of composite materials and fracture mechanics and in studying stress concentrations in composite structural elements.

  12. Predicted tyre-soil interface area and vertical stress distribution based on loading characteristics

    DEFF Research Database (Denmark)

    Schjønning, Per; Stettler, M.; Keller, Thomas

    2015-01-01

    The upper boundary condition for all models simulating stress patterns throughout the soil profile is the stress distribution at the tyre–soil interface. The so-called FRIDA model (Schjønning et al., 2008. Biosyst. Eng. 99, 119–133) treats the contact area as a superellipse and has been shown...... of the actual to recommended inflation pressure ratio. We found that VT and Kr accounted for nearly all variation in the data with respect to the contact area. The contact area width was accurately described by a combination of tyre width and Kr, while the superellipse squareness parameter, n, diminished...... slightly with increasing Kr. Estimated values of the contact area length related to observed data with a standard deviation of about 0.06 m. A difference between traction and implement tyres called for separate prediction equations, especially for the contact area. The FRIDA parameters α and β, reflecting...

  13. Numerical Simulation of Temperature Field and Residual Stress Distribution for Laser Cladding Remanufacturing

    Directory of Open Access Journals (Sweden)

    Liang Hua

    2014-05-01

    Full Text Available A three-dimensional finite element model was employed to simulate the cladding process of Ni-Cr-B-Si coatings on 16MnR steel under different parameters of laser power, scanning speed, and spot diameter. The temperature and residual stress distribution, the depth of the heat affected zone (HAZ, and the optimized parameters for laser cladding remanufacturing technology were obtained. The orthogonal experiment and intuitive analysis on the depth of the HAZ were performed to study the influence of different cladding parameters. A new criterion based on the ratio of the maximum tensile residual stress and fracture strength of the substrate was proposed for optimization of the remanufacturing parameters. The result showed well agreement with that of the HAZ analysis.

  14. Ongoing nationwide outbreak of Salmonella Agona associated with internationally distributed infant milk products, France, December 2017.

    Science.gov (United States)

    Jourdan-da Silva, Nathalie; Fabre, Laetitia; Robinson, Eve; Fournet, Nelly; Nisavanh, Athinna; Bruyand, Mathias; Mailles, Alexandra; Serre, Estelle; Ravel, Magali; Guibert, Véronique; Issenhuth-Jeanjean, Sylvie; Renaudat, Charlotte; Tourdjman, Mathieu; Septfons, Alexandra; de Valk, Henriette; Le Hello, Simon

    2018-01-01

    On 1 December 2017, an outbreak of Salmonella Agona infections among infants was identified in France. To date, 37 cases (median age: 4 months) and two further international cases have been confirmed. Five different infant milk products manufactured at one facility were implicated. On 2 and 10 December, the company recalled the implicated products; on 22 December, all products processed at the facility since February 2017. Trace-forward investigations indicated product distribution to 66 countries.

  15. Exchange rate pass-through and the role of international distribution channels

    OpenAIRE

    Desiraju, Ramarao; Shrikhande, Milind

    1996-01-01

    Manufacturers selling in foreign markets often do not completely pass on the effects of fluctuations in exchange rates to the prices of their products. Our paper addresses this puzzle and studies the effects of the international distribution channel on exchange rate pass-through. We develop an exchange rate pass-through model that takes into account the role of an intermediary between a domestic manufacturer and its consumers in a foreign market. We find that the magnitude of the pass-through...

  16. Influence of anisotropy effect and internal stresses upon the superconductive critical temperature of plastically deformed tin

    International Nuclear Information System (INIS)

    Wagner, D.; Stangler, F.

    1976-01-01

    The influence of plastic deformation on the superconductive critical temperature of tin single crystals has been investigated experimentally. It was shown by measurements that the lattice defects produced by plastic deformation lead to an anisotropy effect (according to the theory of Markowitz and Kadanoff), as do impurities in alloyed material. The decrease in T/sub c/ due to this effect can be measured, however, only with samples of certain special orientations. Samples with other orientations show an increase in T/sub c/, which can be explained by the assumption of internal stresses from dislocation pileups. A model is discussed which accounts for the measured rise in T/sub c/

  17. FLANGE-ORNL, Flanged Pipe Joint Stress Analysis, Internal Pressure, Moment Loads, Temperature

    International Nuclear Information System (INIS)

    Rodabaugh, E.C.; Moore, S.E.

    1979-01-01

    1 - Description of problem or function: FLANGE-ORNL calculates appropriate loads, stresses, and displacements for the flanges, bolts, and gaskets that comprise a flanged piping joint for internal pressure or moment loading on the pipe, temperature difference between the flange hub and ring, and variations in bolt load that result from pressure, hub-ring temperature gradient and/or bolt-ring temperature differences. Flanges considered may be tapered-hub, straight or blind. 2 - Method of solution: The solution is based on discontinuity analysis and the theory of plates and shells

  18. Modelling and analysis of the stress distribution in a multi-thin film system Pt/USG/Si

    Science.gov (United States)

    Yao, W. Z.; Roqueta, F.; Craveur, J. C.; Belhenini, S.; Gardes, P.; Tougui, A.

    2018-04-01

    Residual stress analysis is commonly achieved through curvature measurement with the help of Stoney’s formula. However, this conventional approach is inadequate for multi-layer thin film systems, which are widely used in today’s microelectronics. Also, for the thin film case, the residual stress is composed of thermal stress and intrinsic stress. Measuring the wafer curvature at room temperature provides a value for the average stresses in the layer, the two components cannot be distinguished by the existing methodologies of curvature measurement. To alleviate these problems, a modified curvature method combining finite element (FE) modelling is proposed to study the stress distribution in a Pt/USG/Si structure. A 2D FE model is firstly built in order to calculate the thermal stress in the multilayer structure, the obtained thermal stresses in respective films are verified by an analytical model. Then, we calculate the warpage of the multilayer structure by considering the intrinsic stress in the respective films. The residual stresses in the films are determined by minimizing the difference between the simulated warpage and that of experimental measurement. The proposed approach can be used to calculate not only the average residual stress but also thermal and intrinsic stress components in the USG and Platinum films. The obtained residual and intrinsic stresses from a numerical model are compared with the values of other studies. There is no limitation for the application of our methodologies regarding the number of the layers in the stack.

  19. Preliminary study of internal wave effects to chlorophyll distribution in the Lombok Strait and adjacent areas

    Science.gov (United States)

    Arvelyna, Yessy; Oshima, Masaki

    2005-01-01

    This paper studies the effect of internal wave in the Lombok Strait to chlorophyll distribution in the surrounded areas using ERS SAR, ASTER, SeaWiFS and AVHRR-NOAA images data during 1996-2004 periods. The observation results shows that the internal waves were propagated to the south and the north of strait and mostly occurred during transitional season from dry to wet and wet season (rainy season) between September to December when the layers are strongly stratified. Wavelet transform of image using Meyer wavelet analysis is applied for internal wave detection in ERS SAR and ASTER images, for symmetric extension of data at the image boundaries, to prevent discontinuities by a periodic wrapping of data in fast algorithm and space-saving code. Internal wave created elongated pattern in detail and approximation of image from level 2 to 5 and retained value between 2-4.59 times compared to sea surface, provided accuracy in classification over than 80%. In segmentation process, the Canny edge detector is applied on the approximation image at level two to derive internal wave signature in image. The proposed method can extract the internal wave signature, maintain the continuity of crest line while reduce small strikes from noise. The segmentation result, i.e. the length between crest and trough, is used to compute the internal wave induced current using Korteweg-de Vries (KdV) equation. On ERS SAR data contains surface signature of internal wave (2001/8/20), we calculated that internal wave propagation speed was 1.2 m/s and internal wave induced current was 0.56 m/s, respectively. From the observation of ERS SAR and SeaWiFS images data, we found out that the distribution of maximum chlorophyll area at southern coastline off Bali Island when strong internal wave induced current occurred in south of the Lombok Strait was distributed further to westward, i.e. from 9.25°-10.25°LS, 115°-116.25°SE to 8.8°-10.7°LS, 114.5°-116°SE, and surface chlorophyll concentration

  20. Using internal discharge data in a distributed conceptual model to reduce uncertainty in streamflow simulations

    Science.gov (United States)

    Guerrero, J.; Halldin, S.; Xu, C.; Lundin, L.

    2011-12-01

    Distributed hydrological models are important tools in water management as they account for the spatial variability of the hydrological data, as well as being able to produce spatially distributed outputs. They can directly incorporate and assess potential changes in the characteristics of our basins. A recognized problem for models in general is equifinality, which is only exacerbated for distributed models who tend to have a large number of parameters. We need to deal with the fundamentally ill-posed nature of the problem that such models force us to face, i.e. a large number of parameters and very few variables that can be used to constrain them, often only the catchment discharge. There is a growing but yet limited literature showing how the internal states of a distributed model can be used to calibrate/validate its predictions. In this paper, a distributed version of WASMOD, a conceptual rainfall runoff model with only three parameters, combined with a routing algorithm based on the high-resolution HydroSHEDS data was used to simulate the discharge in the Paso La Ceiba basin in Honduras. The parameter space was explored using Monte-Carlo simulations and the region of space containing the parameter-sets that were considered behavioral according to two different criteria was delimited using the geometric concept of alpha-shapes. The discharge data from five internal sub-basins was used to aid in the calibration of the model and to answer the following questions: Can this information improve the simulations at the outlet of the catchment, or decrease their uncertainty? Also, after reducing the number of model parameters needing calibration through sensitivity analysis: Is it possible to relate them to basin characteristics? The analysis revealed that in most cases the internal discharge data can be used to reduce the uncertainty in the discharge at the outlet, albeit with little improvement in the overall simulation results.

  1. Pressure distribution of implant-supported removable partial dentures with stress-breaking attachments.

    Science.gov (United States)

    Kono, Kentaro; Kurihara, Daisuke; Suzuki, Yasunori; Ohkubo, Chikahiro

    2014-04-01

    This in vitro study investigated the pressure distribution of the implant-supported removable partial dentures (RPDs) with the stress-breaking attachments under the occlusal force. The experimental model of bilateral missing premolars and molars was modified from a commercial simulation model. Five pressure sensors were embedded near the bilateral first molars, first premolars, and medio-lingual alveolar crest. Two implants were placed near the second molars, and they were connected to the denture base using the following conditions: complete separation between the denture base and implant with cover screws (CRPD), flexible connection with a stress-breaking ball (SBB) attachment, and rigid connection without stress breaking with healing caps (HC). The pressure at five different areas of the soft tissue and the displacement of the RPDs were simultaneously measured, loading up to 50 N. The coefficient of variation (CV) for each connection was calculated from all data of the pressure at five areas to evaluate the pressure distribution. The pressure on medio-lingual alveolar crest and molars of the HC was less than SBB and CRPD. In contrast, the pressure on premolars of SBB was greater than for the HC and CRPD. The CV of SBB was less than that of HC and CRPD. Denture displacement of HC and SBB was less than for CRPD. Within the in vitro limitations, precise denture settlements and pressure distribution under the denture base could be controlled using an SBB attachment. An SBB attachment might be able to protect the implant from harmful force. Crown Copyright © 2014. Published by Elsevier Ltd. All rights reserved.

  2. Theoretical role of adjunctive implant positional support in stress distribution of distal-extension mandibular removable partial dentures.

    Science.gov (United States)

    Xiao, Wei; Li, Zhiyong; Shen, Shiqian; Chen, Shaowu; Wang, Yining; Wang, Jiawei

    2014-01-01

    This preliminary study evaluated the adjunctive supporting role of diverse implant positions on stress distribution in a Class I removable partial denture (RPD) design. Nine three-dimensional finite element models were prepared to simulate mandibular RPD designs with three different loading conditions applied. Implant supported designs demonstrated lower stress value concentrations and mucosal displacement.

  3. 78 FR 64153 - Policy Statement on the Principles for Development and Distribution of Annual Stress Test Scenarios

    Science.gov (United States)

    2013-10-28

    .... OCC-2012-0016] Policy Statement on the Principles for Development and Distribution of Annual Stress... the stress test horizon. The variables specified for each scenario generally address economic activity... institutions by November 15th of each year. This document articulates the principles that the OCC will apply to...

  4. 78 FR 72534 - Policy Statement on the Principles for Development and Distribution of Annual Stress Test Scenarios

    Science.gov (United States)

    2013-12-03

    ... FEDERAL DEPOSIT INSURANCE CORPORATION 12 CFR Part 325 Policy Statement on the Principles for... stress test horizon. The variables specified for each scenario generally address economic activity, asset..., 2012, that articulated the principles the FDIC will apply to develop and distribute the stress test...

  5. Stress distribution in dental prosthesis under an occlusal combined dynamic loading

    International Nuclear Information System (INIS)

    Merdji, A.; Bachir Bouiadjra, B.; Ould Chikh, B.; Mootanah, R.; Aminallah, L.; Serier, B.; Muslih, I.M.

    2012-01-01

    Highlights: ► The mechanical stress reaches the highest in areas of cortical bones. ► The mechanical stress in the cancellous bone reaches greatest in the bottom of the dental implant. ► Implant with low-volume bone might cause increased stress concentration in the cortical bone. -- Abstract: The biomechanical behavior of osseointegrated dental prostheses systems plays an important role in its functional longevity inside the bone. Simulation of these systems requires an accurate modeling of the prosthesis components, the jaw bone, the implant–bone interface, and the response of the system to different types of applied forces. The purpose of this study was to develop a new three-dimensional model of an osseointegrated molar dental prosthesis and to carry out finite element analysis to evaluate stress distributions in the bone and the dental prosthesis compounds under an occlusal combined dynamic load was applied to the top of the occlusale face of the prosthesis crown. The jaw bone model containing cortical bone and cancellous bone was constructed by using computer tomography scan pictures and Computer Aided Design tools. The dental prosthesis compounds were constructed, simulating the commercially available cylindrical implant of 4.8 mm diameter and 10 mm length. Both finite element models were created in Abaqus finite element software. All materials used in the models were considered to be isotropic, homogeneous and linearly elastic. The elastic properties, loads and constraints used in the model were taken from published data. Results of our finite element analyses, indicated that the maximum stresses were located around the mesial neck of the implant, in the marginal bone. Thus, this area should be preserved clinically in order to maintain the bone–implant interface structurally and functionally.

  6. Study on improved procedure for determination of three dimensional distributions of the initial rock stresses. 3

    International Nuclear Information System (INIS)

    Mizuta, Yoshiaki

    2004-02-01

    In the fiscal year of 2003, our committee achieved the following work items during the contract period, from September 3rd, 2003 to February 13th, 2004. The more accurate numerical data with respect to the geological/geometrical conditions including the fault were provided from Tono Geoscience Center and the numerical models by Finite Element Method (FEM), Finite Difference Method (FDM) and Boundary Element Method (BEM) were built taking those strata data into account. For small region modeling by FEM, three layers models, Shoumasama model and Tono-Shoumasama model, as well as Tono Mine model, were constructed, and each strain state at the far field boundary was determined. In order to get better agreement in local stress states with the measured values, a far field strain state was determined to the modified model in which material properties of upper granite and lower granite are different. In intermediate region modeling by FDM, actual strata data was taken into account, whereas strata boundary was assumed to be horizontal in former modeling, and far field stress field was analyzed. Intermediate region modeling by BEM was also carried out and far field stress state was determined. In wide region modeling by FEM, the fault was build in the model and fault slip was taken into account, and evaluation of strain state at the far field boundary was carried out for inhomogeneous rock including fault. It was proposed to output three-dimensional distribution of the maximum shear stress coefficients in order to advance three-dimensional modeling. It will make clear effect of shape, scale and property of the fault on stress state characteristic. This report describes minutely the results of the studies mentioned above. (author)

  7. Real-time patient-specific finite element analysis of internal stresses in the soft tissues of a residual limb: a new tool for prosthetic fitting.

    Science.gov (United States)

    Portnoy, S; Yarnitzky, G; Yizhar, Z; Kristal, A; Oppenheim, U; Siev-Ner, I; Gefen, A

    2007-01-01

    Fitting of a prosthetic socket is a critical stage in the process of rehabilitation of a trans-tibial amputation (TTA) patient, since a misfit may cause pressure ulcers or a deep tissue injury (DTI: necrosis of the muscle flap under intact skin) in the residual limb. To date, prosthetic fitting typically depends on the subjective skills of the prosthetist, and is not supported by biomedical instrumentation that allows evaluation of the quality of fitting. Specifically, no technology is presently available to provide real-time continuous information on the internal distribution of mechanical stresses in the residual limb during fitting of the prosthesis, or while using it and this severely limits patient evaluations. In this study, a simplified yet clinically oriented patient-specific finite element (FE) model of the residual limb was developed for real-time stress analysis. For this purpose we employed a custom-made FE code that continuously calculates internal stresses in the residual limb, based on boundary conditions acquired in real-time from force sensors, located at the limb-prosthesis interface. Validation of the modeling system was accomplished by means of a synthetic phantom of the residual limb, which allowed simultaneous measurements of interface pressures and internal stresses. Human studies were conducted subsequently in five TTA patients. The dimensions of bones and soft tissues were obtained from X-rays of the residual limb of each patient. An indentation test was performed in order to obtain the effective elastic modulus of the soft tissues of the residual limb. Seven force sensors were placed between the residual limb and the prosthetic liner, and subjects walked on a treadmill during analysis. Generally, stresses under the shinbones were approximately threefold higher than stresses at the soft tissues behind the bones. Usage of a thigh corset decreased the stresses in the residual limb during gait by approximately 80%. Also, the stresses

  8. Prediction of residual stress distribution in multi-stacked thin film by curvature measurement and iterative FEA

    International Nuclear Information System (INIS)

    Choi, Hyeon Chang; Park, Jun Hyub

    2005-01-01

    In this study, residual stress distribution in multi-stacked film by MEMS (Micro-Electro Mechanical System) process is predicted using Finite Element Method (FEM). We develop a finite element program for REsidual Stress Analysis (RESA) in multi-stacked film. The RESA predicts the distribution of residual stress field in multi-stacked film. Curvatures of multi-stacked film and single layers which consist of the multi-stacked film are used as the input to the RESA. To measure those curvatures is easier than to measure a distribution of residual stress. To verify the RESA, mean stresses and stress gradients of single and multilayers are measured. The mean stresses are calculated from curvatures of deposited wafer by using Stoney's equation. The stress gradients are calculated from the vertical deflection at the end of cantilever beam. To measure the mean stress of each layer in multi-stacked film, we measure the curvature of wafer with the film after etching layer by layer in multi-stacked film

  9. EFFECTS OF VARIOUS SOIL ENVIRONMENTAL STRESSES ON THE OCCURRENCE, DISTRIBUTION AND EFFECTIVENESS OF VA MYCORRHIZAE

    Directory of Open Access Journals (Sweden)

    A.G. KHAN

    1995-01-01

    Full Text Available The vesicular - arbuscular (VA mycorrhizal fungi are geographically ubiquitous soil inhabitants and form universal symbiotic relationship with plants from every phylum. These fungi link host plants with host soils and their biota in the mycorrhizosphere and play an important role in plant health, productivity and soil structure. Although VA mycorrhizal fungi do not show any host specificity, there is increasing evidence that various climatic and edaphic environmental factors such as land use and management practices, physical, chemical and biological properties of host soils and host plant characteristics influence their occurrence, taxonomic distribution and effectiveness. The interaction of these factors with vesicular-arbuscular mycorrhizae (VAM is poorly understood except in a few cases. It is now very clear that VA mycorrhizal associations are ecologically significant factors that require more attention than previously accorded. This paper discusses the occurrence, distribution and significance of VAM in environmentally stressed soil conditions that limit plant growth such as drought, waterlogging and salinity.

  10. Development of integrated damage detection system for international America's Cup class yacht structures using a fiber optic distributed sensor

    Science.gov (United States)

    Akiyoshi, Shimada; Naruse, Hiroshi; Uzawa, Kyoshi; Murayama, Hideaki; Kageyama, Kazuro

    2000-06-01

    We constructed a new health monitoring system to detect damage using a fiber optic distributed sensor, namely a Brillouin optical time domain reflectometer (BOTDR), and installed it in International America's Cup Class (IACC) yachts, the Japanese entry in America's Cup 2000. IACC yachts are designed to be as fast as possible, so it is essential that they are lightweight and encounter minimum water resistance. Advanced composite sandwich structures, made with carbon fiber reinforced plastic (CFRP) skins and a honeycomb core, are used to achieve the lightweight structure. Yacht structure designs push the strength of the materials to their limit and so it is important to detect highly stressed or damaged regions that might cause a catastrophic fracture. The BOTDR measures changes in the Brillouin frequency shift caused by distributed strain along one optical fiber. We undertook two experiments: a pulling test and a four point bending test on a composite beam. The former showed that no slippage occurred between the optical fiber glass and its coating. The latter confirmed that a debonding between the skin and the core of 300 mm length could be found with the BOTDR. Next we examined the effectiveness with which this system can assess the structural integrity of IACC yachts. The results show that our system has the potential for use as a damage detection system for smart structures.

  11. 77 FR 17525 - Cinram Distribution, LLC, a Subsidiary of Cinram International Income Fund, Including On-Site...

    Science.gov (United States)

    2012-03-26

    ... International Income Fund had their wages reported through a separate unemployment insurance (UI) tax account..., a Subsidiary of Cinram International Income Fund, Including On-Site Leased Workers From Good People..., 2012, applicable to workers of Cinram Distribution, LLC, a subsidiary of Cinram International Income...

  12. The Role of Attachment, Travel Experiences and English Proficiency in International Students' Acculturative Stress and Depressive Symptoms

    Science.gov (United States)

    Smiljanic, Iskra

    2017-01-01

    This study examined the relationship between attachment, travel experiences, and English proficiency and international students' acculturative stress and depressive symptoms. A total of 91 graduate international students completed online surveys. Pearson correlations showed that both attachment anxiety and avoidance were positively correlated with…

  13. Relationship between Religious Orientation (Internal-External) With Methods of Overcoming Stress in Students of Islamic Azad University of Abhar

    Science.gov (United States)

    Jafari, Alireza

    2011-01-01

    This study explored the relationship between religious orientation (internal-external) and the ways of coping stress (problem-based and emotion-based) in the students of IAU (Islamic Azad University), Abhar Branch. Religion with internal origin is comprehensive and has well-organized principles. However, religion with external origin is a device…

  14. Associations among mothers' representations of their relationship with their toddlers, maternal parenting stress, and toddlers' internalizing and externalizing behaviors.

    Science.gov (United States)

    Sher-Censor, Efrat; Shulman, Cory; Cohen, Esther

    2018-02-01

    This study examined the array of associations among the emotional valence and the coherence of mothers' representations of their relationship with their toddlers, mothers' reported parenting stress, and toddlers' internalizing and externalizing behaviors. To evaluate maternal representations, 55 mothers were interviewed using the Five Minute Speech Sample procedure (FMSS; Magaña et al., 1986), which was coded for criticism and positive comments (Magaňa-Amato, 1993), as well as coherence (Sher-Censor & Yates, 2015). Mothers also completed the Parenting Stress Index - Short Form (PSI; Abidin, 1997) to evaluate their parenting stress and the Child Behavior Checklist (CBCL/1.5-5; Achenbach & Rescorla, 2000) to assess their toddlers' internalizing and externalizing behaviors. Results indicated that parenting stress was associated with maternal criticism and fewer positive comments in the FMSS, but not with the coherence of mothers' FMSS. Parenting stress, criticism, and lower coherence in the FMSS were associated with maternal reports of externalizing behaviors. Only parenting stress and lower coherence in the FMSS were related to mothers' reports of internalizing behaviors of the child. Thus, the emotional valence and the coherence of mothers' representations of their relationship with their child and parenting stress may each constitute a distinct aspect of parenting and contribute to the understanding of individual differences in toddlers' internalizing and externalizing behaviors. Implications for research and practice with families of toddlers are discussed. Copyright © 2017 Elsevier Inc. All rights reserved.

  15. Stress

    Science.gov (United States)

    ... can be life-saving. But chronic stress can cause both physical and mental harm. There are at least three different types of stress: Routine stress related to the pressures of work, family, and other daily responsibilities Stress brought about ...

  16. The Interactive Effects of Stressful Family Life Events and Cortisol Reactivity on Adolescent Externalizing and Internalizing Behaviors

    Science.gov (United States)

    Steeger, Christine M.; Cook, Emily C.; Connell, Christian M.

    2016-01-01

    This study investigated the associations between stressful family life events and adolescent externalizing and internalizing behaviors, and the interactive effects of family life events and cortisol reactivity on problem behaviors. In a sample of 100 mothers and their adolescents (M age = 15.09; SD age = 0.98; 68% girls), adolescent cortisol reactivity was measured in response to a mother-adolescent conflict interaction task designed to elicit a stress response. Mothers reported on measures of family life events and adolescent problem behaviors. Results indicated that a heightened adolescent cortisol response moderated the relations between stressful family life events and both externalizing and internalizing behaviors. Results support context-dependent theoretical models, suggesting that for adolescents with higher cortisol reactivity (compared to those with lower cortisol reactivity), higher levels of stressful family life events were associated with greater problem behaviors, whereas lower levels of stressful family life events were related to fewer problem behaviors. PMID:26961703

  17. Heterogeneous Cytoskeletal Force Distribution Delineates the Onset Ca2+ Influx Under Fluid Shear Stress in Astrocytes

    Directory of Open Access Journals (Sweden)

    Mohammad M. Maneshi

    2018-03-01

    Full Text Available Mechanical perturbations increase intracellular Ca2+ in cells, but the coupling of mechanical forces to the Ca2+ influx is not well understood. We used a microfluidic chamber driven with a high-speed pressure servo to generate defined fluid shear stress to cultured astrocytes, and simultaneously measured cytoskeletal forces using a force sensitive actinin optical sensor and intracellular Ca2+. Fluid shear generated non-uniform forces in actinin that critically depended on the stimulus rise time emphasizing the presence of viscoelasticity in the activating sequence. A short (ms shear pulse with fast rise time (2 ms produced an immediate increase in actinin tension at the upstream end of the cell with minimal changes at the downstream end. The onset of Ca2+ rise began at highly strained areas. In contrast to stimulus steps, slow ramp stimuli produced uniform forces throughout the cells and only a small Ca2+ response. The heterogeneity of force distribution is exaggerated in cells having fewer stress fibers and lower pre-tension in actinin. Disruption of cytoskeleton with cytochalasin-D (Cyt-D eliminated force gradients, and in those cells Ca2+ elevation started from the soma. Thus, Ca2+ influx with a mechanical stimulus depends on local stress within the cell and that is time dependent due to viscoelastic mechanics.

  18. Influence of Connector Width on the Stress Distribution of Posterior Bridges under Loading

    Directory of Open Access Journals (Sweden)

    A. Azary

    2011-06-01

    Full Text Available Objective: In all ceramic fixed partial dentures the connector area is a common fracture location. The survival time of three-unit fixed partial dentures may be improved by altering the connector design in regions of maximum tension. The purpose of this study was to determine the effect of buccolingual increase of the connector width on the stress distribution in posterior fixed partial dentures made of IPS Empress 2. To simulate the anatomical condition, we used three-dimensional finite element analysis to generate.Materials and Methods: Three models of three-unit bridges replacing the first molar were prepared. The buccolingual connector width varied from 3.0 to 5.0 mm. Bridges were vertically loaded with 600 N at one point on the central fossa of the pontic, at 12 points along the cusp-fossa contact (50 N each, or at eight points along the cusp-marginal ridge contact (75 N each. Alternatively, a load of 225 N was applied at a 45º angle from the lingual side.Results: Stress concentrations were observed within or near the connectors. The von Mises stress decreased by increasing connector width, regardless of whether the loading was applied vertically or at an angle.Conclusion: Within the limitations of this study, we conclude that increasing the connector width decreases the failure probability when a vertical or angled load is applied.

  19. Distribution of Selenium and Oxidative Stress in Breast Tumor-Bearing Mice

    Directory of Open Access Journals (Sweden)

    Pei-Chung Chen

    2013-02-01

    Full Text Available The present study investigated the effects of breast tumors on the blood and tissue distribution of essential trace mineral selenium (Se, and oxidative stress status of mice. Female 10-week-old BALB/cByJNarl mice were randomly assigned into control (CNL and breast tumor-bearing (TB groups. TB mice were injected subcutaneously into the right hind thigh with 5 × 106 EMT6 mouse mammary tumor cells. After 22 days, we measured Se concentrations, Se-dependent glutathione peroxidase (GPx activities, and malondialdehyde (MDA products (indicator of oxidative stress in plasma, various tissues, and plasma vascular endothelial growth factor (VEGF concentrations. There were no significant differences in body weights and daily intake between both groups. Compared with the CNL group, TB mice have decreases in plasma Se concentrations and GPx activities, as well as higher plasma VEGF and MDA concentrations. Plasma Se concentrations were also negatively correlated with plasma MDA and VEGF concentrations. Furthermore, tissue Se concentrations and GPx activities in TB animals were lower; whereas the MDA concentrations higher in various tissues including liver, kidney, brain, lung, spleen, and thymic tissues. In conclusion, disruption of Se homeostasis critically reflects oxidative stress in target tissues, thus may increase the risk for progression of breast cancer and metastasis.

  20. Miniaturization of Micro-Solder Bumps and Effect of IMC on Stress Distribution

    Science.gov (United States)

    Choudhury, Soud Farhan; Ladani, Leila

    2016-07-01

    As the joints become smaller in more advanced packages and devices, intermetallic (IMCs) volume ratio increases, which significantly impacts the overall mechanical behavior of joints. The existence of only a few grains of Sn (Tin) and IMC materials results in anisotropic elastic and plastic behavior which is not detectable using conventional finite element (FE) simulation with average properties for polycrystalline material. In this study, crystal plasticity finite element (CPFE) simulation is used to model the whole joint including copper, Sn solder and Cu6Sn5 IMC material. Experimental lap-shear test results for solder joints from the literature were used to validate the models. A comparative analysis between traditional FE, CPFE and experiments was conducted. The CPFE model was able to correlate the experiments more closely compared to traditional FE analysis because of its ability to capture micro-mechanical anisotropic behavior. Further analysis was conducted to evaluate the effect of IMC thickness on stress distribution in micro-bumps using a systematic numerical experiment with IMC thickness ranging from 0% to 80%. The analysis was conducted on micro-bumps with single crystal Sn and bicrystal Sn. The overall stress distribution and shear deformation changes as the IMC thickness increases. The model with higher IMC thickness shows a stiffer shear response, and provides a higher shear yield strength.

  1. Application of a distributed optical fiber sensing technique in monitoring the stress of precast piles

    International Nuclear Information System (INIS)

    Lu, Y; Shi, B; Wei, G Q; Zhang, D; Chen, S E

    2012-01-01

    Due to its ability in providing long distance, distributed sensing, the optical fiber sensing technique based on a Brillouin optical time domain reflectometer (BOTDR) has a unique advantage in monitoring the stability and safety of linear structures. This paper describes the application of a BOTDR-based technique to measure the stress within precast piles. The principle behind the BOTDR and the embedding technique for the sensing optical fiber in precast piles is first introduced, and then the analysis method and deformation and stress calculation based on distributed strain data are given. Finally, a methodology for using a BOTDR-based monitoring workflow for in situ monitoring of precast piles, combined with a practical example, is introduced. The methodology requires implantation of optical fibers prior to pile placement. Field experimental results show that the optical fiber implantation method with slotting, embedding, pasting and jointing is feasible, and have accurately measured the axial force, side friction, end-bearing resistance and bearing feature of the precast pile according to the strain measuring data. (paper)

  2. Analysis of temperature and stress distribution of superheater tubes after attemperation or sootblower activation

    International Nuclear Information System (INIS)

    Madejski, Paweł; Taler, Dawid

    2013-01-01

    Highlights: • The CFD simulation was used to calculate 3D steam and tube wall temperature distributions in the platen superheater. • The CFD results can be used in design of superheaters made of tubes with complex cross-section. • The CFD analysis enables the proper selection of the steel grade. • The transient temperature and stress distributions were calculated using Finite Volume Method. • The detailed analysis prevents superheater tubes from excessive stresses during sootblower or attemperator activation. - Abstract: Superheaters are characterized by high metal temperatures due to higher steam temperature and low heat transfer coefficients on the tube inner surfaces. Superheaters have especially difficult operating conditions, particularly during attemperator and sootblower activations, when temperature and steam flow rate as well as tube wall temperature change with time. A detailed thermo-mechanical analysis of the superheater tubes makes it possible to identify the cause of premature high-temperature failures and aids greatly in the changes in tubing arrangement and improving start-up technology. This paper presents a thermal and strength analysis of a tube “double omega”, used in the steam superheaters in CFB boilers

  3. Effect of Taper on Stress Distribution of All Ceramic Fixed Partial Dentures: a 3D-FEA Study

    Directory of Open Access Journals (Sweden)

    F. Gerami-Panah

    2005-09-01

    Full Text Available Statement of Problem: Mechanical failure of ceramic materials is controlled by brittle fracture, mostly occurred in tension. In 3-unit all-ceramic FPDs the connector area is considered to be at fracture risk because of tensile stress concentrations.Purpose: The aim of this FE analysis was to evaluate the effect of taper on stress distribution in all-ceramic FPDs.Materials and Methods: In this experimental study two 3-D finite element models of thee-unit IPS-Empress 2 FPDs replacing mandible second premolar were created by means of finite element software. The digital images were obtained from CT scan of human skull. Abutment was reduced with 12 and 22 degrees of taper. The cement layer,PDL, cancellous bone and cortical bone were also modeled. Frameworks of core material were fabricated. A static load of 100 N was applied at mid pontic area.Resolved stresses were calculated according to the Von Mises criterion and principal stresses.Results: In both models stresses were concentrated at the connectors. The maximum stresses were lower in the model with larger taper. The maximum Von Mises stress was recorded at the connector region of the premolar and the pontic. In model with larger taper the patterns of stresses were also more distributed and less concentrated.Conclusion: The highest Von Mises and principal stress were recorded at the connectors. Tensile stresses developed at the gingival connector of premolar and pontic was higher than molar. The stress level in model with 22-degree taper was lower compare to 12-degree and the stress pattern was more distributed, lowered the risk ofconcentrations.

  4. The Effect of Composite Thickness on the Stress Distribution Pattern of Restored Premolar Teeth with Cusp Reduction.

    Science.gov (United States)

    Panahandeh, Narges; Torabzadeh, Hassan; Ziaee, Nargess; Mahdian, Mina; Tootiaee, Bahman; Ghasemi, Amir

    2017-07-01

    Different thicknesses of restorative material can alter the stress distribution pattern in remaining tooth structure. The assumption is that a thicker composite restoration will induce a higher fracture resistance. Therefore, the present study evaluated the effect of composite thickness on stress distribution in a restored premolar with cusp reduction. A 3D solid model of a maxillary second premolar was prepared and meshed. MOD cavities were designed with different cusp reduction thicknesses (0, 0.5, 1, 1.5, 2.5 mm). Cavities were restored with Valux Plus composite. They were loaded with 200 N force on the occlusal surface in the direction of the long axis. Von Mises stresses were evaluated with Abaqus software. Stress increased from occlusal to gingival and was maximum in the cervical region. The stressed area in the palatal cusp was more than that of the buccal cusp. Increasing the thickness of composite altered the shear stress to compressive stress in the occlusal area of the teeth. The model with 2.5 mm cusp reduction exhibited the most even stress distribution. © 2015 by the American College of Prosthodontists.

  5. SPR Characteristics Curve and Distribution of Residual Stress in Self-Piercing Riveted Joints of Steel Sheets

    OpenAIRE

    Haque, Rezwanul; Wong, Yat C.; Paradowska, Anna; Blacket, Stuart; Durandet, Yvonne

    2017-01-01

    Neutron diffraction was used to describe the residual stress distributions in self-piercing riveted (SPR) joints. The sheet material displayed a compressive residual stress near the joint, and the stress gradually became tensile in the sheet material far away from the joint. The stress in the rivet leg was lower in the thick joint of the softer steel sheet than in the thin joint of the harder steel sheet. This lower magnitude was attributed to the lower force gradient during the rivet flaring...

  6. Stress distribution and contact area measurements of a gecko toe using a high-resolution tactile sensor.

    Science.gov (United States)

    Eason, Eric V; Hawkes, Elliot W; Windheim, Marc; Christensen, David L; Libby, Thomas; Cutkosky, Mark R

    2015-02-02

    The adhesive systems of geckos have been widely studied and have been a great source of bioinspiration. Load-sharing (i.e. preventing stress concentrations through equal distribution of loads) is necessary to maximize the performance of an adhesive system, but it is not known to what extent load-sharing occurs in gecko toes. In this paper, we present in vivo measurements of the stress distribution and contact area on the toes of a tokay gecko (Gekko gecko) using a custom tactile sensor with 100 μm spatial resolution. We found that the stress distributions were nonuniform, with large variations in stress between and within lamellae, suggesting that load-sharing in the tokay gecko is uneven. These results may be relevant to the understanding of gecko morphology and the design of improved synthetic adhesive systems.

  7. Stress distribution and contact area measurements of a gecko toe using a high-resolution tactile sensor

    International Nuclear Information System (INIS)

    Eason, Eric V; Hawkes, Elliot W; Christensen, David L; Cutkosky, Mark R; Windheim, Marc; Libby, Thomas

    2015-01-01

    The adhesive systems of geckos have been widely studied and have been a great source of bioinspiration. Load-sharing (i.e. preventing stress concentrations through equal distribution of loads) is necessary to maximize the performance of an adhesive system, but it is not known to what extent load-sharing occurs in gecko toes. In this paper, we present in vivo measurements of the stress distribution and contact area on the toes of a tokay gecko (Gekko gecko) using a custom tactile sensor with 100 μm spatial resolution. We found that the stress distributions were nonuniform, with large variations in stress between and within lamellae, suggesting that load-sharing in the tokay gecko is uneven. These results may be relevant to the understanding of gecko morphology and the design of improved synthetic adhesive systems. (paper)

  8. The Influence of Pressure Distribution on the Maximum Values of Stress in FEM Analysis of Plain Bearings

    Directory of Open Access Journals (Sweden)

    Vasile Cojocaru

    2016-12-01

    Full Text Available Several methods can be used in the FEM studies to apply the loads on a plain bearing. The paper presents a comparative analysis of maximum stress obtained for three loading scenarios: resultant force applied on the shaft – bearing assembly, variable pressure with sinusoidal distribution applied on the bearing surface, variable pressure with parabolic distribution applied on the bearing surface.

  9. [Influence of attachment type on stress distribution of implant-supported removable partial dentures].

    Science.gov (United States)

    Yang, Xue; Rong, Qi-guo; Yang, Ya-dong

    2015-02-18

    To compare influences of different retention attachments on stress among supporting structures. By 3-dimensional laser scanner and reverse engineering computer aided design (CAD) software, a basic partially edentulous digital model with mandibular premolar and molar missing was established. Implant attachment and removable partial dentures (RPD) were added into the basic model to build three kinds of models: RPD only, RPD + implant + Locator attachment, and RPD + implant + Magfit attachment. Vertical and inclined loads were put on artificial teeth unilaterally. By means of 3-dimensional finite element analysis, the stress distribution and displacement of the main supportive structures were compared. A complete 3-dimensional finite element model was established, which contained tooth structure, and periodontal structures. The displacement of the denture was smaller in Locator (9.38 μm vertically, 45.48 μm obliquely) and Magfit models (9.54 μm vertically, 39.45 μm obliquely) compared with non-implant RPD model (95.27 μm vertically, 155.70 μm obliquely). Compared with the two different attachments, cortical bone stress value was higher in Locator model (Locator model 10.850 MPa vertically, 43.760 MPa obliquely; Magfit model 7.100 MPa vertically, 19.260 MPa obliquely).The stress value of abutment periodontal ligamentin Magfit model (0.420 MPa vertically) was lower than that in Locator model (0.520 MPa vertically). The existence of implant could reduce maximum von Mises value of each supportive structure when Kennedy I partially edentulous mandible was restored. Comparing the structure of Magfit and Locator attachment, the contact of Magfit attachment was rigid, while Locator was resilient. Locator attachment could improve stability of the denture dramatically. Locator had stronger effect on defending horizontal movement of the denture.

  10. Status report: Intergranular stress corrosion cracking of BWR core shrouds and other internal components

    International Nuclear Information System (INIS)

    1996-03-01

    On July 25, 1994, the US Nuclear Regulatory Commission (NRC) issued Generic Letter (GL) 94-03 to obtain information needed to assess compliance with regulatory requirements regarding the structural integrity of core shrouds in domestic boiling water reactors (BWRs). This report begins with a brief description of the safety significance of intergranular stress corrosion cracking (IGSCC) as it relates to the design and function of BWR core shrouds and other internal components. It then presents a brief history of shroud cracking events both in the US and abroad, followed by an indepth summary of the industry actions to address the issue of IGSCC in BWR core shrouds and other internal components. This report summarizes the staff's basis for issuing GL 94-03, as well as the staff's assessment of plant-specific responses to GL 94-03. The staff is continually evaluating the licensee inspection programs and the results from examinations of BWR core shrouds and other internal components. This report is representative of submittals to and evaluations by the staff as of September 30, 1995. An update of this report will be issued at a later date

  11. Evaluation of Residual Stress Distribution and Relaxation on In Situ TiB2/7050 Al Composites

    Directory of Open Access Journals (Sweden)

    Kunyang Lin

    2018-04-01

    Full Text Available Interior residual stresses induced by quenching may cause distortion during subsequent machining processes. Hence, various strategies have been employed to relieve the interior residual stress, such as stretching, post treatment, and other techniques. In this study, the stress distribution inside TiB2/7050 Al composite extrusions was investigated and the effects of different methods on relieving the quenching-induced stress were compared. Firstly, three TiB2/7050 Al composite extrusions were treated by stretching, stretching and heat treatment, and stretching and cold treatment processes, respectively. Then, the multiple-cut contour method was employed to assess the residual stresses in the three workpieces. Experimental results indicate that the interior stress of TiB2/7050 Al composite extrusions after stretching ranges from −89 MPa to +55 MPa, which is larger than that in 7050 aluminum alloy, which ranges from −25 Pa to +25 MPa. The heat treatment performs better than the cold treatment to reduce the post-stretching residual stress, with a reduction of 23.2–46.4% compared to 11.3–40.8%, respectively. From the stress map, it is found that the stress distribution after the heat treatment is more uniform compared with that after the cold treatment.

  12. Variable content and distribution of arabinogalactan proteins in banana (Musa spp.) under low temperature stress.

    Science.gov (United States)

    Yan, Yonglian; Takáč, Tomáš; Li, Xiaoquan; Chen, Houbin; Wang, Yingying; Xu, Enfeng; Xie, Ling; Su, Zhaohua; Šamaj, Jozef; Xu, Chunxiang

    2015-01-01

    Information on the spatial distribution of arabinogalactan proteins (AGPs) in plant organs and tissues during plant reactions to low temperature (LT) is limited. In this study, the extracellular distribution of AGPs in banana leaves and roots, and their changes under LT stress were investigated in two genotypes differing in chilling tolerance, by immuno-techniques using 17 monoclonal antibodies against different AGP epitopes. Changes in total classical AGPs in banana leaves were also tested. The results showed that AGP epitopes recognized by JIM4, JIM14, JIM16, and CCRC-M32 antibodies were primarily distributed in leaf veins, while those recognized by JIM8, JIM13, JIM15, and PN16.4B4 antibodies exhibited predominant sclerenchymal localization. Epitopes recognized by LM2, LM14, and MAC207 antibodies were distributed in both epidermal and mesophyll cells. Both genotypes accumulated classical AGPs in leaves under LT treatment, and the chilling tolerant genotype contained higher classical AGPs at each temperature treatment. The abundance of JIM4 and JIM16 epitopes in the chilling-sensitive genotype decreased slightly after LT treatment, and this trend was opposite for the tolerant one. LT induced accumulation of LM2- and LM14-immunoreactive AGPs in the tolerant genotype compared to the sensitive one, especially in phloem and mesophyll cells. These epitopes thus might play important roles in banana LT tolerance. Different AGP components also showed differential distribution patterns in banana roots. In general, banana roots started to accumulate AGPs under LT treatment earlier than leaves. The levels of AGPs recognized by MAC207 and JIM13 antibodies in the control roots of the tolerant genotype were higher than in the chilling sensitive one. Furthermore, the chilling tolerant genotype showed high immuno-reactivity against JIM13 antibody. These results indicate that several AGPs are likely involved in banana tolerance to chilling injury.

  13. Identification of potential internal control genes for real-time PCR analysis during stress response in Pyropia haitanensis

    Science.gov (United States)

    Wang, Xia; Feng, Jianhua; Huang, Aiyou; He, Linwen; Niu, Jianfeng; Wang, Guangce

    2017-11-01

    Pyropia haitanensis has prominent stress-resistance characteristics and is endemic to China. Studies into the stress responses in these algae could provide valuable information on the stress-response mechanisms in the intertidal Rhodophyta. Here, the effects of salinity and light intensity on the quantum yield of photosystem II in Py. haitanensis were investigated using pulse-amplitude-modulation fluorometry. Total RNA and genomic DNA of the samples under different stress conditions were isolated. By normalizing to the genomic DNA quantity, the RNA content in each sample was evaluated. The cDNA was synthesized and the expression levels of seven potential internal control genes were evaluated using qRT-PCR method. Then, we used geNorm, a common statistical algorithm, to analyze the qRT-PCR data of seven reference genes. Potential genes that may constantly be expressed under different conditions were selected, and these genes showed stable expression levels in samples under a salinity treatment, while tubulin, glyceraldehyde-3-phosphate dehydrogenase and actin showed stability in samples stressed by strong light. Based on the results of the pulse amplitude-modulation fluorometry, an absolute quantification was performed to obtain gene copy numbers in certain stress-treated samples. The stably expressed genes as determined by the absolute quantification in certain samples conformed to the results of the geNorm screening. Based on the results of the software analysis and absolute quantification, we proposed that elongation factor 3 and 18S ribosomal RNA could be used as internal control genes when the Py. haitanensis blades were subjected to salinity stress, and that α-tubulin and 18S ribosomal RNA could be used as the internal control genes when the stress was from strong light. In general, our findings provide a convenient reference for the selection of internal control genes when designing experiments related to stress responses in Py. haitanensis.

  14. Internalization of external cost for the production and distribution of electricity in Flanders, Belgium

    International Nuclear Information System (INIS)

    Torfs, R.; De Nocker, L.; Schrooten, L.; Aernouts, K.; Liekens, I.

    2005-04-01

    This report elaborates the external costs of electricity production and distribution in Flanders, Belgium, and tests them against prices and taxes for electricity use. The authors examined whether these external costs decrease in time and whether such a decrease leads to internalization in the price for the users through taxes, levies or other economic instruments. The external costs mainly include external environmental costs caused by air pollution and greenhouse gases, but also damage caused by accidents, hindrance and radioactive substances that may be released. [nl

  15. 13th International Symposium on Distributed Computing and Artificial Intelligence 2016

    CERN Document Server

    Semalat, Ali; Bocewicz, Grzegorz; Sitek, Paweł; Nielsen, Izabela; García, Julián; Bajo, Javier

    2016-01-01

    The 13th International Symposium on Distributed Computing and Artificial Intelligence 2016 (DCAI 2016) is a forum to present applications of innovative techniques for studying and solving complex problems. The exchange of ideas between scientists and technicians from both the academic and industrial sector is essential to facilitate the development of systems that can meet the ever-increasing demands of today’s society. The present edition brings together past experience, current work and promising future trends associated with distributed computing, artificial intelligence and their application in order to provide efficient solutions to real problems. This symposium is organized by the University of Sevilla (Spain), Osaka Institute of Technology (Japan), and the Universiti Teknologi Malaysia (Malaysia).

  16. Influence of Additive Manufactured Scaffold Architecture on the Distribution of Surface Strains and Fluid Flow Shear Stresses and Expected Osteochondral Cell Differentiation.

    Science.gov (United States)

    Hendrikson, Wim J; Deegan, Anthony J; Yang, Ying; van Blitterswijk, Clemens A; Verdonschot, Nico; Moroni, Lorenzo; Rouwkema, Jeroen

    2017-01-01

    Scaffolds for regenerative medicine applications should instruct cells with the appropriate signals, including biophysical stimuli such as stress and strain, to form the desired tissue. Apart from that, scaffolds, especially for load-bearing applications, should be capable of providing mechanical stability. Since both scaffold strength and stress-strain distributions throughout the scaffold depend on the scaffold's internal architecture, it is important to understand how changes in architecture influence these parameters. In this study, four scaffold designs with different architectures were produced using additive manufacturing. The designs varied in fiber orientation, while fiber diameter, spacing, and layer height remained constant. Based on micro-CT (μCT) scans, finite element models (FEMs) were derived for finite element analysis (FEA) and computational fluid dynamics (CFD). FEA of scaffold compression was validated using μCT scan data of compressed scaffolds. Results of the FEA and CFD showed a significant impact of scaffold architecture on fluid shear stress and mechanical strain distribution. The average fluid shear stress ranged from 3.6 mPa for a 0/90 architecture to 6.8 mPa for a 0/90 offset architecture, and the surface shear strain from 0.0096 for a 0/90 offset architecture to 0.0214 for a 0/90 architecture. This subsequently resulted in variations of the predicted cell differentiation stimulus values on the scaffold surface. Fluid shear stress was mainly influenced by pore shape and size, while mechanical strain distribution depended mainly on the presence or absence of supportive columns in the scaffold architecture. Together, these results corroborate that scaffold architecture can be exploited to design scaffolds with regions that guide specific tissue development under compression and perfusion. In conjunction with optimization of stimulation regimes during bioreactor cultures, scaffold architecture optimization can be used to improve

  17. [Effect of zirconia abutment angulation on stress distribution in the abutment and the bone around implant: a finite element study].

    Science.gov (United States)

    Yang, Yan-zhong; Tian, Xiao-hua; Zhou, Yan-min

    2015-08-01

    To investigate the effect of three different zirconia angular abutments on the stress distribution in bone and abutment using three-dimensional finite element analysis, and provide instruction for clinical application. Finite element analysis (FEA) was applied to analyze the stress distribution of three different zirconia/titanium angular abutments and bone around implant. The maximum Von Minses stress that existed in abutment, bolt and bone of the angular abutment model was significantly higher than that existed in the straight abutment model. The maximum Von Minses stress that existed in abutment, bolt and bone of the 20 ° angular abutment model was significantly higher than that existed in 15 ° angular abutment model. There was no significant difference between zirconia abutment model and titanium abutment model. The abutment angulation has a significant influence on the stress distribution in the abutment, bolt and bone, and exacerbates as the angulation increases, which suggest that we should take more attention to the implant orientation and use straight abutment or little angular abutment. The zirconia abutment can be used safely, and there is no noticeable difference between zirconia abutment and titanium abutment on stress distribution.

  18. A deep learning approach to estimate stress distribution: a fast and accurate surrogate of finite-element analysis.

    Science.gov (United States)

    Liang, Liang; Liu, Minliang; Martin, Caitlin; Sun, Wei

    2018-01-01

    Structural finite-element analysis (FEA) has been widely used to study the biomechanics of human tissues and organs, as well as tissue-medical device interactions, and treatment strategies. However, patient-specific FEA models usually require complex procedures to set up and long computing times to obtain final simulation results, preventing prompt feedback to clinicians in time-sensitive clinical applications. In this study, by using machine learning techniques, we developed a deep learning (DL) model to directly estimate the stress distributions of the aorta. The DL model was designed and trained to take the input of FEA and directly output the aortic wall stress distributions, bypassing the FEA calculation process. The trained DL model is capable of predicting the stress distributions with average errors of 0.492% and 0.891% in the Von Mises stress distribution and peak Von Mises stress, respectively. This study marks, to our knowledge, the first study that demonstrates the feasibility and great potential of using the DL technique as a fast and accurate surrogate of FEA for stress analysis. © 2018 The Author(s).

  19. The bio-distribution of the antidepressant clomipramine is modulated by chronic stress in mice: Effects on behavior

    Directory of Open Access Journals (Sweden)

    Georgia eBalsevich

    2015-01-01

    Full Text Available Major depression is one of the most common psychiatric disorders, severely affecting the quality of life of millions of people worldwide. Despite the availability of several classes of antidepressants, treatment efficacy is still very variable and many patients do not respond to the treatment. Clomipramine (CMI, a classical and widely used antidepressant, shows widespread interindividual variability of efficacy, while the environmental factors contributing to such variability remain unclear. We investigated whether chronic stress modulates the bio-distribution of CMI, and as a result the behavioral response to CMI treatment in a mouse model of chronic social defeat stress. Our results show that stress exposure increased anxiety-like and depressive-like behaviors and altered the stress response. Chronic defeat stress furthermore significantly altered CMI bio-distribution. Interestingly, CMI bio-distribution highly correlated with anxiety-like and depressive-like behaviors only under basal conditions. Taken together, we provide first evidence demonstrating that chronic stress exposure modulates CMI bio-distribution and behavioral responses. This may contribute to CMI’s broad interindividual variability, and is especially relevant in clinical practice.

  20. Influence of occlusal contact area on cusp defection and stress distribution.

    Science.gov (United States)

    Costa, Anna Karina Figueiredo; Xavier, Thaty Aparecida; Paes-Junior, Tarcisio José Arruda; Andreatta-Filho, Oswaldo Daniel; Borges, Alexandre Luiz Souto

    2014-11-01

    The purpose of this study was to evaluate the effect of occlusal contact area for loading on the cuspal defection and stress distribution in a first premolar restored with a high elastic modulus restorative material. The Rhinoceros 4.0 software was used for modeling the three-dimensional geometries of dental and periodontal structures and the inlay restoration. Thus, two different models, intact and restored teeth with three occlusal contact areas, 0.1, 0.5 and 0.75 mm(2), on enamel at the occlusal surface of buccal and lingual cusps. Finite element analysis (FEA) was performed with the program ANSYS (Workbench 13.0), which generated a mesh with tetrahedral elements with greater refinement in the regions of interest, and was constrained at the bases of cortical and trabecular bone in all axis and loaded with 100 N normal to each contact area. To analysis of maximum principal stress, the smaller occlusal contact area showed greater compressive stress in region of load application for both the intact and inlay restored tooth. However, tensile stresses at the occlusal isthmus were similar for all three tested occlusal contact areas (60 MPa). To displacement of the cusps was higher for teeth with inlay (0.46-0.48 mm). For intact teeth, the smaller contact area showed greater displacement (0.10 mm). For teeth with inlays, the displacement of the cusps were similar in all types of occlusal area. Cuspal displacement was higher in the restored tooth when compared to the intact tooth, but there were no significant variations even with changes in the occlusal contact area. RELEVANCE CLINICAL: Occlusal contacts have a great influence on the positioning of teeth being able to maintain the position and stability of the mandible. Axial loads would be able to generate more uniform stress at the root presenting a greater concentration of load application in the point and the occlusal surface. Thus, is necessary to analyze the relationship between these occlusal contacts as dental

  1. Influence of intrinsic and extrinsic forces on 3D stress distribution using CUDA programming

    Science.gov (United States)

    Räss, Ludovic; Omlin, Samuel; Podladchikov, Yuri

    2013-04-01

    In order to have a better understanding of the influence of buoyancy (intrinsic) and boundary (extrinsic) forces in a nonlinear rheology due to a power law fluid, some basics needs to be explored through 3D numerical calculation. As first approach, the already studied Stokes setup of a rising sphere will be used to calibrate the 3D model. Far field horizontal tectonic stress is applied to the sphere, which generates a vertical acceleration, buoyancy driven. This simple and known setup allows some benchmarking performed through systematic runs. The relative importance of intrinsic and extrinsic forces producing the wide variety of rates and styles of deformation, including absence of deformation and generating 3D stress patterns, will be determined. Relation between vertical motion and power law exponent will also be explored. The goal of these investigations will be to run models having topography and density structure from geophysical imaging as input, and 3D stress field as output. The stress distribution in Swiss Alps and Plateau and its implication for risk analysis is one of the perspective for this research. In fact, proximity of the stress to the failure is fundamental for risk assessment. Sensitivity of this to the accurate topography representation can then be evaluated. The developed 3D numerical codes, tuned for mid-sized cluster, need to be optimized, especially while running good resolution in full 3D. Therefor, two largely used computing platforms, MATLAB and FORTRAN 90 are explored. Starting with an easy adaptable and as short as possible MATLAB code, which is then upgraded in order to reach higher performance in simulation times and resolution. A significant speedup using the rising NVIDIA CUDA technology and resources is also possible. Programming in C-CUDA, creating some synchronization feature, and comparing the results with previous runs, helps us to investigate the new speedup possibilities allowed through GPU parallel computing. These codes

  2. Finite Element Analysis of the Effect of Proximal Contour of Class II Composite Restorations on Stress Distribution

    Directory of Open Access Journals (Sweden)

    Hossein Abachizadeh

    2012-09-01

    Full Text Available Introduction: The aim of this study was to evaluate the effect of proximal contour of class II composite restorations placed with straight or contoured matrix band using composite resins with different modulus of elasticity on stress distribution by finite element method. Methods: In order to evaluate the stress distribution of class II composite restorations using finite element method, upper right first molar and second premolar were modeled. Proximal boxes were designed and restored with universal Z250 and packable P60 composite resins (3M ESPE using two matrix systems: flat Tofflemire matrix and precurved sectional matrix. Finally models were evaluated under loads of 200 and 400 Newton at 90 degrees angle and the results were graphically illustrated in the form of Von Misses stresses. Results: In general the stress obtained under 400 Newton load was significantly greater than the stress of models under 200 Newton load. Von Misses stress distribution pattern of two different Z250 and P60 composites were very similar in all modes of loading and proximal contour. In all analyzed models there was a significant difference between models restored with Tofflemire matrix with flat contour and models restored with sectional matrix with curved contour. This difference was greater in first molar than second premolar. Conclusion: Use of a contoured matrix band results in less stress in class II composite resin restorations.

  3. Stress distribution and displacement of abutment of middle implant-natural teeth fixed bridge under different loading

    International Nuclear Information System (INIS)

    Chen Erjun; Zhou Yanmin; Ma Chenchun; Cong Zhiqiang; Jiang Yonghua

    2004-01-01

    Objective: To study stress distribution and displacement of abutment of middle implant-natural teeth fixed bridge under different loading. Methods: The stress distribution and displacement of abutment were studied and analyzed by means of three-dimensional finite element when different loading was applied. Results: The biggest stress of middle implant was 4-5 times as big as that of natural teeth. Under concentrated vertical loading, the biggest stress of implant was about 2 times higher than that under dispersed vertical loading. There was no significant difference of biggest stress on the implant between concentrated oblique loading and dispersed oblique loading. The biggest stress of implant under oblique loading was 3 times as big as that under dispersed vertical loading. The biggest stress of natural teeth under dispersed loading was lower than that under concentrated loading. The maximum displacement of implant in occlusal-gum direction was great lower than that of natural teeth. Both in buccal-lingual direction and medial-distal direction, the displacement of implant were about equal to that of natural teeth. Conclusion: The oblique loading is the main force to destroy the middle implant-natural teeth fixed bridge. The lean of cusp should be reduced. The abnormally high occlusal points should be deleted. The bite points should be well distributed. The fixed bridge is feasible. (authors)

  4. Stochastic variability in stress, sleep duration, and sleep quality across the distribution of body mass index: insights from quantile regression.

    Science.gov (United States)

    Yang, Tse-Chuan; Matthews, Stephen A; Chen, Vivian Y-J

    2014-04-01

    Obesity has become a problem in the USA and identifying modifiable factors at the individual level may help to address this public health concern. A burgeoning literature has suggested that sleep and stress may be associated with obesity; however, little is know about whether these two factors moderate each other and even less is known about whether their impacts on obesity differ by gender. This study investigates whether sleep and stress are associated with body mass index (BMI) respectively, explores whether the combination of stress and sleep is also related to BMI, and demonstrates how these associations vary across the distribution of BMI values. We analyze the data from 3,318 men and 6,689 women in the Philadelphia area using quantile regression (QR) to evaluate the relationships between sleep, stress, and obesity by gender. Our substantive findings include: (1) high and/or extreme stress were related to roughly an increase of 1.2 in BMI after accounting for other covariates; (2) the pathways linking sleep and BMI differed by gender, with BMI for men increasing by 0.77-1 units with reduced sleep duration and BMI for women declining by 0.12 unit with 1 unit increase in sleep quality; (3) stress- and sleep-related variables were confounded, but there was little evidence for moderation between these two; (4) the QR results demonstrate that the association between high and/or extreme stress to BMI varied stochastically across the distribution of BMI values, with an upward trend, suggesting that stress played a more important role among adults with higher BMI (i.e., BMI > 26 for both genders); and (5) the QR plots of sleep-related variables show similar patterns, with stronger effects on BMI at the upper end of BMI distribution. Our findings suggested that sleep and stress were two seemingly independent predictors for BMI and their relationships with BMI were not constant across the BMI distribution.

  5. Control superstructure of rigid polyelectrolytes in oppositely charged hydrogels via programmed internal stress

    Science.gov (United States)

    Takahashi, Riku; Wu, Zi Liang; Arifuzzaman, Md; Nonoyama, Takayuki; Nakajima, Tasuku; Kurokawa, Takayuki; Gong, Jian Ping

    2014-08-01

    Biomacromolecules usually form complex superstructures in natural biotissues, such as different alignments of collagen fibres in articular cartilages, for multifunctionalities. Inspired by nature, there are efforts towards developing multiscale ordered structures in hydrogels (recognized as one of the best candidates of soft biotissues). However, creating complex superstructures in gels are hardly realized because of the absence of effective approaches to control the localized molecular orientation. Here we introduce a method to create various superstructures of rigid polyanions in polycationic hydrogels. The control of localized orientation of rigid molecules, which are sensitive to the internal stress field of the gel, is achieved by tuning the swelling mismatch between masked and unmasked regions of the photolithographic patterned gel. Furthermore, we develop a double network structure to toughen the hydrogels with programmed superstructures, which deform reversibly under large strain. This work presents a promising pathway to develop superstructures in hydrogels and should shed light on designing biomimetic materials with intricate molecular alignments.

  6. Determination of internal controls for quantitative gene expression of Isochrysis zhangjiangensis at nitrogen stress condition

    Science.gov (United States)

    Wu, Shuang; Zhou, Jiannan; Cao, Xupeng; Xue, Song

    2016-02-01

    Isochrysis zhangjiangensis is a potential marine microalga for biodiesel production, which accumulates lipid under nitrogen limitation conditions, but the mechanism on molecular level is veiled. Quantitative real-time polymerase chain reaction (qPCR) provides the possibility to investigate the gene expression levels, and a valid reference for data normalization is an essential prerequisite for firing up the analysis. In this study, five housekeeping genes, actin (ACT), α-tubulin (TUA), ß-tubulin (TUB), ubiquitin (UBI), 18S rRNA (18S) and one target gene, diacylglycerol acyltransferase (DGAT), were used for determining the reference. By analyzing the stabilities based on calculation of the stability index and on operating the two types of software, geNorm and bestkeeper, it showed that the reference genes widely used in higher plant and microalgae, such as UBI, TUA and 18S, were not the most stable ones in nitrogen-stressed I. zhangjiangensis, and thus are not suitable for exploring the mRNA expression levels under these experimental conditions. Our results show that ACT together with TUB is the most feasible internal control for investigating gene expression under nitrogen-stressed conditions. Our findings will contribute not only to future qPCR studies of I. zhangjiangensis, but also to verification of comparative transcriptomics studies of the microalgae under similar conditions.

  7. On Shear Stress Distributions for Flow in Smooth or Partially Rough Annuli

    Energy Technology Data Exchange (ETDEWEB)

    Kjellstroem, B; Hedberg, S

    1966-08-15

    It is commonly assumed that for turbulent flow in annuli the radii of zero shear and maximum velocity are coincident. By inspection of the differential equations for such flow and by an integral analysis it is shown that this is not necessarily true. To check whether important differences could occur, experiments were made in which velocity and shear stress distributions were measured in one smooth and two partially rough annuli. The results show no difference in the radii for the smooth annulus, but for the partially rough annuli there was a small but significant difference. This difference explains the breakdown of Hall's transformation theory reported by other investigators. The error introduced by use of Hall's theory is however small, of the order of 10 % or less.

  8. On Shear Stress Distributions for Flow in Smooth or Partially Rough Annuli

    International Nuclear Information System (INIS)

    Kjellstroem, B.; Hedberg, S.

    1966-08-01

    It is commonly assumed that for turbulent flow in annuli the radii of zero shear and maximum velocity are coincident. By inspection of the differential equations for such flow and by an integral analysis it is shown that this is not necessarily true. To check whether important differences could occur, experiments were made in which velocity and shear stress distributions were measured in one smooth and two partially rough annuli. The results show no difference in the radii for the smooth annulus, but for the partially rough annuli there was a small but significant difference. This difference explains the breakdown of Hall's transformation theory reported by other investigators. The error introduced by use of Hall's theory is however small, of the order of 10 % or less

  9. Sex differences in the tracer distribution on stress thallium-201 imaging, (1)

    International Nuclear Information System (INIS)

    Tamaki, Nagara; Koda, Hideki; Adachi, Yukihide; Sugihara, Takao; Kato, Mihoko; Tanaka, Nobuyuki; Tamari, Kimimasa.

    1988-01-01

    To determine the sex differences in the tracer distribution on stress thallium-201 imaging, the studies of 18 normal males and 18 normal females were subjected to quantitative circumferential profile analysis in each projection image. Although the exercise duration was shorter in females (11±3 min) than in males (14±3 min) (p<0.01), the peak heart rate, peak systolic pressure and the lung-to-myocardial count ratio were similar between them. The averaged profile curves in female showed a significant reduction in tracer uptake in anterior and upper septal regions, particularly in the study of lateral view, which may be attributed to breast attenuation. In addition, the percent washout of thallium in 3 hours was higher in females (48±8%) than in males (43±7%) (p<0.01), particularly in the study of anterior view. We conclude that important differences in the pattern of thallium uptake and washout between males and females should be considered for interpretation of stress thallium imaging. (author)

  10. Factorial Validity and Internal Consistency of Malaysian Adapted Depression Anxiety Stress Scale - 21 in an Adolescent Sample

    OpenAIRE

    Hairul Anuar Hashim; Freddy Golok; Rosmatunisah Ali

    2011-01-01

    Background: Psychometrically sound measurement instrument is a fundamental requirement across broad range of research areas. In negative affect research, Depression Anxiety Stress Scale (DASS) has been identified as a psychometrically sound instrument to measure depression, anxiety and stress, especially the 21-item version. However, its psychometric properties in adolescents have been less consistent. Objectives: Thus, the present study sought to examine the factorial validity and internal c...

  11. Distribution system choice in a service industry: An analysis of international insurance firms operating in the United States

    NARCIS (Netherlands)

    Parente, R.; Choi, B.P.; Slangen, A.H.L.; Ketkar, S.

    2010-01-01

    Service firms play an increasingly important role in the global economy. However, the internationalization strategies of such firms, and especially their distribution system choices, have been underexplored in the international management literature. One specific service industry that has

  12. Effect of Oval Posts on Stress Distribution in Endodontically Treated Teeth: A Three-Dimensional Finite Element Analysis

    Directory of Open Access Journals (Sweden)

    Mojtaba Mahmoodi

    2017-09-01

    Full Text Available Introduction: In post-core crown restorations, the use of prefabricated composite posts concentrate stress at the cervical region and the use of metal posts (prefabricated and customized posts concentrates stress at the interfaces. Fiber reinforced composite posts (FRCs with oval cross-section (oval posts were proposed for post-core crown restorations to reduce the stress levels at the cervical region. The aim of the present study was to investigate the impact of oval cross-section composite posts on stress distribution of premolar with oval-shaped canal by using three-dimensional (3D finite element analysis. Materials and Methods: An extracted premolar tooth was mounted, sectioned, and photographed to create a 3D model. The surrounding tissues of the tooth, periodontal ligament, as well as cortical and trabecular bones were modeled. Seven taper posts with two different cross-section geometries (circular and oval shapes were modeled, as well. Then, the effect of post geometry, post material (carbon fiber and fiberglass, and cement material were investigated by 3D finite element analysis and the stress distribution results were compared. Results: In all the models, the highest stress levels of the dentin were accumulated at the coronal third of the root, and the highest stress levels at the bonding layers were accumulated at the cervical margin. Narrow circular posts induced the highest stress levels, whereas the stress levels were reduced by using thick oval posts. Application of elastic cement reduces the stress at the bonding layers but increases stress at the dentin. Conclusion: Finite element analysis showed that prefabricated oval posts are superior to traditional circular ones. The use of cement with low elastic modulus reduces the risk of debonding but raises the risk of root fracture.

  13. Measurements of internal stresses in bond coating using high energy x-rays from synchrotron radiation source

    CERN Document Server

    Suzuki, K; Akiniwa, Y; Nishio, K; Kawamura, M; Okado, H

    2002-01-01

    Thermal barrier coating (TBC) techniques enable high temperature combustion of turbines made of Ni-base alloy. TBC is made of zirconia top coating on NiCoCrAlY bond coating. The internal stresses in the bond coating play essential role in the delamination or fracture of TBC in service. With the X-rays from laboratory equipments, it is impossible to measure nondestructively the internal stress in the bond coating under the top coating. synchrotron radiations with a high energy and high brightness have a large penetration depth as compared with laboratory X-rays. Using the high energy X-rays from the synchrotron radiation, it is possible to measure the internal stress in the bond coating through the top coating. In this study, the furnace, which can heat a specimen to 1473 K, was developed for the stress measurement of the thermal barrier coatings. The internal stresses in the bond coating were measured at the room temperature, 773 K, 1073 K and 1373 K by using the 311 diffraction from Ni sub 3 Al with about 73...

  14. Psychological well-being of interns in Hong Kong: what causes them stress and what helps them.

    Science.gov (United States)

    Lam, T P; Wong, J G W S; Ip, Mary S M; Lam, K F; Pang, S L

    2010-01-01

    Many doctors experience psychological ill health. Interns are known to be particularly vulnerable. To examine the level of depression, anxiety and stress in interns in Hong Kong, as well as the causes and how they cope. A questionnaire was designed based on the themes identified in three focus groups of medical graduates of Year 2004 of the University of Hong Kong. The 21-item Depression, Anxiety and Stress Scale (DASS 21) was also administered. All 155 graduates of the same year were invited to participate with a response rate of 63%. Percentages of respondents with abnormal levels of depression, anxiety and stress were 35.8%, 35.4% and 29.2%, respectively. Frequent calls during night shift, long working hours and heavy workload constituted the most significant stressors. Factor analysis of the stressors showed that seven factors could explain 68% of the total variance: multidisciplinary team working issues, clinical difficulties, job seeking and employment, workload issues, ethical and interpersonal issues, adjustment to job rotation and performance appraisal. Holidays, peers and sleep offered the most significant relief. Interns experience considerable depression, anxiety and stress. The source of stress is multi-faceted, but workload is the most significant stressor. Peer support groups may relief stress.

  15. Stress-intensity factors for a thick-walled cylinder containing an annular imbedded or external or internal surface crack

    Science.gov (United States)

    Erdol, R.; Erdogan, F.

    1976-01-01

    The elastostatic axisymmetric problem for a long thick-walled cylinder containing a ring-shaped internal or edge crack is considered. Using the standard transform technique the problem is formulated in terms of an integral equation which has a simple Cauchy kernel for the internal crack and a generalized Cauchy kernel for the edge crack as the dominant part. As examples the uniform axial load and the steady-state thermal stress problems have been solved and the related stress intensity factors have been calculated. Among other findings the results show that in the cylinder under uniform axial stress containing an internal crack the stress intensity factor at the inner tip is always greater than that at the outer tip for equal net ligament thicknesses and in the cylinder with an edge crack which is under a state of thermal stress the stress intensity factor is a decreasing function of the crack depth, tending to zero as the crack depth approaches the wall thickness.

  16. Effect of Local Strain Distribution of Cold-Rolled Alloy 690 on Primary Water Stress Corrosion Crack Growth Behavior

    Directory of Open Access Journals (Sweden)

    Kim S.-W.

    2017-06-01

    Full Text Available This work aims to study the stress corrosion crack growth behavior of cold-rolled Alloy 690 in the primary water of a pressurized water reactor. Compared with Alloy 600, which shows typical intergranular cracking along high angle grain boundaries, the cold-rolled Alloy 690, with its heterogeneous microstructure, revealed an abnormal crack growth behavior in mixed mode, that is, in transgranular cracking near a banded region, and in intergranular cracking in a matrix region. From local strain distribution analysis based on local mis-orientation, measured along the crack path using the electron back scattered diffraction method, it was suggested that the abnormal behavior was attributable to a heterogeneity of local strain distribution. In the cold-rolled Alloy 690, the stress corrosion crack grew through a highly strained area formed by a prior cold-rolling process in a direction perpendicular to the maximum principal stress applied during a subsequent stress corrosion cracking test.

  17. Investigating the Effect of Drought Stress on Growth and distribution of Purple Nutsedge (Cyperus rotundus L.

    Directory of Open Access Journals (Sweden)

    N. Karimi Arpanahi

    2017-08-01

    Full Text Available Introduction: Drought is one of the most important and common environmental stresses in the country, which affect different stages of plant growth and development. Drought can affect plants growth in various ways, thereby reduces and delays germination, and decreases shoot growth and dry matter production. In the case of high water stress, it results showed great reductions in photosynthesis and disruption of the physiological processes, as well as growth stop and eventually plant death.Purple nutsedge (Cyperus rotundus L. has been listed as the world’s worst weed based onits worldwide distribution (92 countries and interference with over 50 crops. It causes high yield losses in fruiting vegetables and cucurbits in eastern and southeastern parts of Iran, where drought stress is a common phenomenon. Therefore, it is of utmost importance to understand the response of this noxious weed species to drought stress. Materials and Methods: In order to study the effect of drought stress on growth and distribution of purple nutsedge, two separate experiments were carried out in a randomized complete block design with three replications in the Research Greenhouse at Birjand University in 2013. The first experiment consisted of 6 irrigation interval levels (3, 6, 9, 12, 15 and 18- day irrigation intervals and the second one were 5 irrigation levels based on field capacity (12.5, 25, 50, 75 and 100 % FC. Results and Discussion: ANOVA results of both experiments showed that all growth characteristics of purple nutsedge were affected by drought stress. The results of irrigation interval stress experiment showed that the maximum height (76 cm, leaf area (110.83 cm2, stem number (4.66 stemperpot, shoot dry weight (4.132 gr per plant, tuber number (7.66 tuber per pot and total underground organs dry weight (4.435 gr per plant were observed in 3- day irrigation interval. Also, the lowest amount of these characteristics was obtained in 18- day irrigation interval

  18. Validation of post-traumatic stress disorder (PTSD) and complex PTSD using the International Trauma Questionnaire.

    Science.gov (United States)

    Hyland, P; Shevlin, M; Brewin, C R; Cloitre, M; Downes, A J; Jumbe, S; Karatzias, T; Bisson, J I; Roberts, N P

    2017-09-01

    The 11th version of the International Classification of Diseases (ICD-11) has proposed two related trauma diagnoses: Post-traumatic stress disorder (PTSD) and Complex PTSD (CPTSD). Using a newly developed, disorder-specific measure of PTSD and CPTSD called the International Trauma Questionnaire (ITQ) the current study will (i) assess the factorial validity of ICD-11 PTSD and CPTSD; (ii) provide the first test of the discriminant validity of these constructs; and (iii) provide the first comparison of ICD-11, and Diagnostic and Statistical Manual, Fifth Edition (DSM-5), PTSD diagnostic rates using disorder-specific measures. ICD-11 and DSM-5 PTSD-specific measures were completed by a British clinical sample of trauma-exposed patients (N = 171). The structure and validity of ICD-11 PTSD and CPTSD were assessed by means of factor analysis and assessing relationships with criterion variables. Diagnostic rates under ICD-11 were significantly lower than those under DSM-5. A two-factor second-order model reflecting the distinction between PTSD and CPTSD best represented the data from the ITQ; and the PTSD and CPTSD factors differentially predicted multiple psychological variables. The factorial and discriminant validity of ICD-11 PTSD and CPTSD was supported, and ICD-11 produces fewer diagnostic cases than DSM-5. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  19. Effects of water stress on the distribution of 14C-assimilates in young apple trees (mauls pumila mill.)

    International Nuclear Information System (INIS)

    Dong Jiankang; Deng Ximin; Zeng Xiang

    1994-01-01

    Young apple trees were treated by water stress and 14 CO 2 was fed to leaves. Distribution of assimilates in source and sink organs was determined. The results show that plant water deficit increased the proportion of 14 C-assimilates remained in source leaves, and decreased the proportion of 13 C-assimilates exported into the developing fruits. Water stress also significantly decreased the photosynthetic rate of leaves and the growth rate of plants

  20. Personality assessment inventory internalizing and externalizing structure in veterans with posttraumatic stress disorder: associations with aggression.

    Science.gov (United States)

    Van Voorhees, Elizabeth E; Dennis, Paul A; Elbogen, Eric B; Clancy, Carolina P; Hertzberg, Michael A; Beckham, Jean C; Calhoun, Patrick S

    2014-01-01

    Posttraumatic stress disorder (PTSD) is associated with aggressive behavior in veterans, and difficulty controlling aggressive urges has been identified as a primary postdeployment readjustment concern. Yet only a fraction of veterans with PTSD commit violent acts. The goals of this study were to (1) examine the higher-order factor structure of Personality Assessment Inventory (PAI) scales in a sample of U.S. military veterans seeking treatment for PTSD; and (2) to evaluate the incremental validity of higher-order latent factors of the PAI over PTSD symptom severity in modeling aggression. The study sample included male U.S. Vietnam (n = 433) and Iraq/Afghanistan (n = 165) veterans who were seeking treatment for PTSD at an outpatient Veterans Affairs (VA) clinic. Measures included the Clinician Administered PTSD Scale, the PAI, and the Conflict Tactics Scale. The sample was randomly split into two equal subsamples (n's = 299) to allow for cross-validation of statistically derived factors. Parallel analysis, variable clustering analysis, and confirmatory factor analyses were used to evaluate the factor structure, and regression was used to examine the association of factor scores with self-reports of aggression over the past year. Three factors were identified: internalizing, externalizing, and substance abuse. Externalizing explained unique variance in aggression beyond PTSD symptom severity and demographic factors, while internalizing and substance abuse did not. Service era was unrelated to reports of aggression. The constructs of internalizing versus externalizing dimensions of PTSD may have utility in identifying characteristics of combat veterans in the greatest need of treatment to help manage aggressive urges. Published 2014 Wiley Periodicals, Inc.

  1. preparation and distribution of microfiche in International Nuclear Information System (INIS)

    International Nuclear Information System (INIS)

    Kajiro, Tadashi; Habara, Tadashi

    1981-01-01

    INIS started the activity in 1970 aiming at the unified treatment of atomic energy literatures in the world. At present, 66 countries and 13 international organs participate in it, and the INIS Section in IAEA supervises the system. The participants treat the atomic energy literatures published in respective countries and send to the INIS Section in the form of magnetic tapes and others. These informations are returned to respective countries through the publication of ''INIS Atomindex'' and the distribution of the magnetic tapes for mechanized retrieval. Recently, the number of abstracted papers reached about 80000/year. One of the features of this system is to utilize microfiche as the medium of literature distribution, and the literatures which cannot be bought through bookstores are available in the form of microfiche from the INIS Clearing House. The microfiche before the establishment of INIS, the troubles concerning the equipment and the problems of the originals to make microfiche, the change of duplicating films and the conversion of frame number, the adoption of the standard for microfiche production and quality inspection, the second change of duplicating films, the recent improvement of microfiche, and the present state of the production and distribution of microfiche in the INIS Section are described. (Kako, I.)

  2. SPR Characteristics Curve and Distribution of Residual Stress in Self-Piercing Riveted Joints of Steel Sheets

    Directory of Open Access Journals (Sweden)

    Rezwanul Haque

    2017-01-01

    Full Text Available Neutron diffraction was used to describe the residual stress distributions in self-piercing riveted (SPR joints. The sheet material displayed a compressive residual stress near the joint, and the stress gradually became tensile in the sheet material far away from the joint. The stress in the rivet leg was lower in the thick joint of the softer steel sheet than in the thin joint of the harder steel sheet. This lower magnitude was attributed to the lower force gradient during the rivet flaring stage of the SPR process curve. This study shows how the residual stress results may be related to the physical occurrences that happened during joining, using the characteristics curve. The study also shows that neutron diffraction technique enabled a crack in the rivet tip to be detected which was not apparent from a cross-section.

  3. The residual stress distribution in welded pipe inner surface of stainless steel from the nuclear power plant in Ringhals

    International Nuclear Information System (INIS)

    Larsson, L.E.

    1984-06-01

    The axial residual stress distribution on the inner surface of welded pipes of stainless steel SS 2333 (AISI 304) have been measured using the X-ray diffraction technique. Four halves of two pipes with the outer diameter of 114 mm and wall thickness of 10 mm were investigated. The result on the pipe inner surface shows compressive stresses in the weld metal and tensile stresses within a region between 8-23 mm with a maximum of 180MPa at a distance of 17 mm from the weld centerline. The maximum axial and circumferential residual stresses on the pipe outer surface are of the magnitude of 100 MPa. By cutting the pipes into two halves these stresses are relaxed by about 35 MPa. (author)

  4. High energy x-ray synchrotron radiation analysis of residual stress distribution of shot-peened steels

    International Nuclear Information System (INIS)

    Tanaka, Keisuke; Akiniwa, Yoshiaki; Kimachi, Hirohisa; Suzuki, Kenji; Yanase, Etsuya; Nishio, Kouji; Kusumi, Yukihiro

    2001-01-01

    A high energy X-ray beam from synchrotron radiation source SPring-8 was used to determine the residual stress distribution beneath the shot-peened surface of carbon steel plates. By using the monochromatic X-ray beam with an energy of 72 keV, the relation between 2θ and sin 2 ψ was obtained by the side-inclination method upto sin 2 ψ = 0.9. The distribution of the residual stress was determined from the non-linearity of the relation between 2θ and sin 2 ψ. (author)

  5. Determination of the plastic deformation and residual stress tensor distribution using surface and bulk intrinsic magnetic properties

    International Nuclear Information System (INIS)

    Hristoforou, E.; Svec, P. Sr.

    2015-01-01

    We have developed an unique method to provide the stress calibration curve in steels: performing flaw-less welding in the under examination steel, we obtained to determine the level of the local plastic deformation and the residual stress tensors. These properties where measured using both the X-ray and the neutron diffraction techniques, concerning their surface and bulk stresses type II (intra-grain stresses) respectively, as well as the stress tensor type III by using the electron diffraction technique. Measuring the distribution of these residual stresses along the length of a welded sample or structure, resulted in determining the local stresses from the compressive to tensile yield point. Local measurement of the intrinsic surface and bulk magnetic property tensors allowed for the un-hysteretic correlation. The dependence of these local magnetic tensors with the above mentioned local stress tensors, resulting in a unique and almost un-hysteretic stress calibration curve of each grade of steel. This calibration integrated the steel's mechanical and thermal history, as well as the phase transformations and the presence of precipitations occurring during the welding process.Additionally to that, preliminary results in different grade of steels reveal the existence of a universal law concerning the dependence of magnetic and magnetostrictive properties of steels on their plastic deformation and residual stress state, as they have been accumulated due to their mechanical and thermal fatigue and history. This universality is based on the unique dependence of the intrinsic magnetic properties of steels normalized with a certain magnetoelastic factor, upon the plastic deformation or residual stress state, which, in terms, is normalized with their yield point of stress. (authors)

  6. Bimodal effect of oxidative stress in internal anal sphincter smooth muscle

    Science.gov (United States)

    Singh, Jagmohan; Kumar, Sumit

    2015-01-01

    Changes in oxidative stress may affect basal tone and relaxation of the internal anal sphincter (IAS) smooth muscle in aging. We examined this issue by investigating the effects of the oxidative stress inducer 6-anilino-5,8-quinolinedione (LY-83583) in basal as well as U-46619-stimulated tone, and nonadrenergic, noncholinergic (NANC) relaxation in rat IAS. LY-83583, which works via generation of reactive oxygen species in living cells, produced a bimodal effect in IAS tone: lower concentrations (0.1 nM to 10 μM) produced a concentration-dependent increase, while higher concentrations (50–100 μM) produced a decrease in IAS tone. An increase in IAS tone by lower concentrations was associated with an increase in RhoA/Rho kinase (ROCK) activity. This was evident by the increase in RhoA/ROCK in the particulate fractions, in ROCK activity, and in the levels of phosphorylated (p) Thr696-myosin phosphatase target subunit 1 and pThr18/Ser19-20-kDa myosin light chain. Conversely, higher concentrations of LY-83583 produced inhibitory effects on RhoA/ROCK. Interestingly, both the excitatory and inhibitory effects of LY-83583 in the IAS were reversed by superoxide dismutase. The excitatory effects of LY-83583 were found to resemble those with neuronal nitric oxide synthase (nNOS) inhibition by l-NNA, since it produced a significant increase in the IAS tone and attenuated NANC relaxation. These effects of LY-83583 and l-NNA were reversible by l-arginine. This suggests the role of nNOS inhibition and RhoA/ROCK activation in the increase in IAS tone by LY-83583. These data have important implications in the pathophysiology and therapeutic targeting of rectoanal disorders, especially associated with IAS dysfunction. PMID:26138467

  7. Using X-ray microbeam diffraction to study the long-range internal stresses in aluminum processed by ECAP

    International Nuclear Information System (INIS)

    Lee, I-Fang; Phan, Thien Q.; Levine, Lyle E.; Tischler, Jonathan Z.; Geantil, Peter T.; Huang, Yi; Langdon, Terence G.; Kassner, Michael E.

    2013-01-01

    Aluminum alloy 1050 was processed by equal-channel angular pressing (ECAP) using a single pass (equivalent uniaxial strain of about 0.88). Long-range internal stresses (LRISs) were assessed in the grain/subgrain interiors using X-ray microbeam diffraction to measure the spacing of {5 3 1} planes, with normals oriented approximately +27.3°, +4.9° and −17.5° off the pressing (axial) direction. The results are consistent with mechanical analysis that suggests the maximum tensile plastic-strain after one pass is expected for +22.5°, roughly zero along the pressing axis, and maximum compressive strain for the −67.5° direction. The magnitude of the measured maximum compressive long-range internal stress is about 0.13σ a (applied stress) in low-dislocation regions within the grain/subgrain interiors. This work is placed in the context of earlier work where convergent beam electron diffraction was used to analyze LRISs in close proximity to the deformation-induced boundaries. The results are complementary and the measured stresses are consistent with a composite model for long-range internal stresses

  8. Effect of elasticity on stress distribution in CAD/CAM dental crowns: Glass ceramic vs. polymer-matrix composite.

    Science.gov (United States)

    Duan, Yuanyuan; Griggs, Jason A

    2015-06-01

    Further investigations are required to evaluate the mechanical behaviour of newly developed polymer-matrix composite (PMC) blocks for computer-aided design/computer-aided manufacturing (CAD/CAM) applications. The purpose of this study was to investigate the effect of elasticity on the stress distribution in dental crowns made of glass-ceramic and PMC materials using finite element (FE) analysis. Elastic constants of two materials were determined by ultrasonic pulse velocity using an acoustic thickness gauge. Three-dimensional solid models of a full-coverage dental crown on a first mandibular molar were generated based on X-ray micro-CT scanning images. A variety of load case-material property combinations were simulated and conducted using FE analysis. The first principal stress distribution in the crown and luting agent was plotted and analyzed. The glass-ceramic crown had stress concentrations on the occlusal surface surrounding the area of loading and the cemented surface underneath the area of loading, while the PMC crown had only stress concentration on the occlusal surface. The PMC crown had lower maximum stress than the glass-ceramic crown in all load cases, but this difference was not substantial when the loading had a lateral component. Eccentric loading did not substantially increase the maximum stress in the prosthesis. Both materials are resistant to fracture with physiological occlusal load. The PMC crown had lower maximum stress than the glass-ceramic crown, but the effect of a lateral loading component was more pronounced for a PMC crown than for a glass-ceramic crown. Knowledge of the stress distribution in dental crowns with low modulus of elasticity will aid clinicians in planning treatments that include such restorations. Copyright © 2015 Elsevier Ltd. All rights reserved.

  9. Scanning electron-acoustic imaging of residual stress distributions in aluminum metal and ZrSiO4 multiphase ceramics

    International Nuclear Information System (INIS)

    Zhang, B.Y.; Jiang, F.M.; Shi, Y.; Yin, Q.R.; Qian, M.L.

    1997-01-01

    The scanning electron-acoustic imaging technique has been used in the characterization of the residual stress field distributions existing in the subsurface in aluminum disks and 20 vol% SiC ( w)/ZrSiO 4 multiphase ceramics left by Vicker close-quote s indentation. The experimental results reveal that the distribution areas are the plastic-elastic interchange zones. The electron-acoustic signal generation mechanism in the samples are discussed. copyright 1997 American Institute of Physics

  10. Influence of implantoplasty on stress distribution of exposed implants at different bone insertion levels

    Directory of Open Access Journals (Sweden)

    João Paulo Mendes TRIBST

    2017-12-01

    Full Text Available Abstract This study evaluated the effect of implantoplasty on different bone insertion levels of exposed implants. A model of the Bone Level Tapered implant (Straumann Institute, Waldenburg, Switzerland was created through the Rhinoceros software (version 5.0 SR8, McNeel North America, Seattle, WA, USA. The abutment was fixed to the implant through a retention screw and a monolithic crown was modeled over a cementation line. Six models were created with increasing portions of the implant threads exposed: C1 (1 mm, C2 (2 mm, C3 (3 mm, C4 (4 mm, C5 (5 mm and C6 (6 mm. The models were made in duplicates and one of each pair was used to simulate implantoplasty, by removing the threads (I1, I2, I3, I4, I5 and I6. The final geometry was exported in STEP format to ANSYS (ANSYS 15.0, ANSYS Inc., Houston, USA and all materials were considered homogeneous, isotropic and linearly elastic. To assess distribution of stress forces, an axial load (300 N was applied on the cusp. For the periodontal insert, the strains increased in the peri-implant region according to the size of the exposed portion and independent of the threads’ presence. The difference between groups with and without implantoplasty was less than 10%. Critical values were found when the inserted portion was smaller than the exposed portion. In the exposed implants, the stress generated on the implant and retention screw was higher in the models that received implantoplasty. For the bone tissue, exposure of the implant’s thread was a damaging factor, independent of implantoplasty. Implantoplasty treatment can be safely used to control peri-implantitis if at least half of the implant is still inserted in bone.

  11. Using Distributed Operations to Enable Science Research on the International Space Station

    Science.gov (United States)

    Bathew, Ann S.; Dudley, Stephanie R. B.; Lochmaier, Geoff D.; Rodriquez, Rick C.; Simpson, Donna

    2011-01-01

    In the early days of the International Space Station (ISS) program, and as the organization structure was being internationally agreed upon and documented, one of the principal tenets of the science program was to allow customer-friendly operations. One important aspect of this was to allow payload developers and principle investigators the flexibility to operate their experiments from either their home sites or distributed telescience centers. This telescience concept was developed such that investigators had several options for ISS utilization support. They could operate from their home site, the closest telescience center, or use the payload operations facilities at the Marshall Space Flight Center in Huntsville, Alabama. The Payload Operations Integration Center (POIC) processes and structures were put into place to allow these different options to its customers, while at the same time maintain its centralized authority over NASA payload operations and integration. For a long duration space program with many scientists, researchers, and universities expected to participate, it was imperative that the program structure be in place to successfully facilitate this concept of telescience support. From a payload control center perspective, payload science operations require two major elements in order to make telescience successful within the scope of the ISS program. The first element is decentralized control which allows the remote participants the freedom and flexibility to operate their payloads within their scope of authority. The second element is a strong ground infrastructure, which includes voice communications, video, telemetry, and commanding between the POIC and the payload remote site. Both of these elements are important to telescience success, and both must be balanced by the ISS program s documented requirements for POIC to maintain its authority as an integration and control center. This paper describes both elements of distributed payload

  12. The Role of Distal Minority Stress and Internalized Transnegativity in Suicidal Ideation and Nonsuicidal Self-Injury Among Transgender Adults.

    Science.gov (United States)

    Staples, Jennifer M; Neilson, Elizabeth C; Bryan, Amanda E B; George, William H

    Transgender people are at elevated risk for nonsuicidal self-injury (NSSI) and suicidal ideation compared to the general population. Transgender (trans) refers to a diverse group of people who experience incongruence between their gender identity and sex assigned at birth. The present study is guided by the minority stress model and the psychological mediation framework, which postulate that sexual minority groups experience elevated stress as a result of anti-minority prejudice, contributing to negative mental health outcomes. This study utilized these theories to investigate the role of internalized transnegativity-internalization of negative societal attitudes about one's trans identity-in the relationships of distal trans stress to suicidal ideation and NSSI. A U.S. national sample of trans adults (N = 237) completed a battery of online measures. Structural equation modeling (SEM) was used to compare models with mediation and moderation effects. Results suggested that internalized transnegativity acts as both a mediator and a moderator in the relationship between distal trans stress and suicidal ideation. Log likelihood comparisons suggested moderation models had the superior fit for these data. Results suggest that clinical interventions should directly target individuals' internalized transnegativity as well as societal-level transnegativity.

  13. Early Pubertal Maturation and Internalizing Problems in Adolescence: Sex Differences in the Role of Cortisol Reactivity to Interpersonal Stress

    Science.gov (United States)

    Natsuaki, Misaki N.; Klimes-Dougan, Bonnie; Ge, Xiaojia; Shirtcliff, Elizabeth A.; Hastings, Paul D.; Zahn-Waxler, Carolyn

    2009-01-01

    An accumulating body of literature has shown a link between early pubertal maturation and internalizing problems, particularly among girls. Our knowledge is, however, limited with regard to what accounts for this association. Based on a hypothesis that early maturing girls have heightened stress sensitivity that increases the risk of internalizing…

  14. Quality of life among adolescents with sickle cell disease: Mediation of pain by internalizing symptoms and parenting stress

    Directory of Open Access Journals (Sweden)

    Daniel Lauren C

    2008-08-01

    Full Text Available Abstract Background This study aimed to clarify associations between pain, psychological adjustment, and family functioning with health-related quality of life (HRQOL in a sample of adolescents with sickle cell disease (SCD utilizing teen- and parent-report. Methods Forty-two adolescents (between the ages of 12 and 18 with SCD and their primary caregivers completed paper-and-pencil measures of pain, teen's psychological adjustment, and HRQOL. In addition, primary caregivers completed a measure of disease-related parenting stress. Medical file review established disease severity. Results Pearson correlations identified significant inverse associations of pain frequency with physical and psychosocial domains of HRQOL as rated by the teen and primary caregiver. Generally, internalizing symptoms (i.e. anxiety and depression and disease-related parenting stress were also significantly correlated with lower HRQOL. Examination of possible mediator models via a series of regression analyses confirmed that disease-related parenting stress served as a mediator between pain frequency and physical and psychosocial HRQOL. Less consistent were findings for mediation models involving internalizing symptoms. For these, parent-rated teen depression and teen anxiety served as mediators of the association of pain frequency and HRQOL. Conclusion Results are consistent with extant literature that suggests the association of pain and HRQOL and identify concomitant pain variables of internalizing symptoms and family variables as mediators. Efforts to improve HRQOL should aim to address internalizing symptoms associated with pain as well as parenting stress in the context of SCD management.

  15. Contributions to Internal Stress from Free Dislocations and from Substructure Boundaries in Dislocation Structure Formed in High Temperature Creep

    Czech Academy of Sciences Publication Activity Database

    Orlová, Alena; Dobeš, Ferdinand

    2008-01-01

    Roč. 567-568, - (2008), s. 173-176 ISSN 0255-5476. [MSMF /5./. Brno, 27.06.2007-29.06.2007] R&D Projects: GA AV ČR 1QS200410502 Institutional research plan: CEZ:AV0Z20410507 Keywords : creep * internal stress * subgrain * dislocation density Subject RIV: BM - Solid Matter Physics ; Magnetism

  16. Treatment of stress fracture of the olecranon in throwing athletes with internal fixation through a small incision

    Directory of Open Access Journals (Sweden)

    Fujioka Hiroyuki

    2012-12-01

    Full Text Available Abstract The present study is a report of retrospective case series of stress fracture of the olecranon. Six patients presented posterior elbow pain in throwing in baseball and softball, but fracture was not diagnosed in radiographs. We detected stress fracture of the olecranon using computed tomographic (CT scan and treated the patient with internal fixation with a headless cannulated double threaded screw through a small skin incision. All patients returned to competitive level without elbow complaints after the operation. When throwing athletes present with unusual posterior elbow pain and no significant findings on radiographs, a CT scan examination should be performed. We recommend surgical treatment of internal fixation with a screw through a small skin incision, as a good option for stress fracture of the olecranon in order to allow early return to sports activity in competitive athletes.

  17. The Distribution and Environmental Impacts of Noise Pollution Sadouqi Martyr Yazd International Airport Using GIS

    Directory of Open Access Journals (Sweden)

    H Zarei Mahmoud Abadi

    2016-03-01

    Full Text Available Introduction: Persecutors of aircraft noise at an airport has a close relationship with the alternate of landing and take-off weight of the aircraft and operations planning during the night. Now aircraft that spill in Yazd airport and take-off of aircraft is of jet engines or so-turbofan mean that the resulting sound will be very high. Methods: In this descriptive, cross-sectional  measurement of noise from aircraft traffic noise measuring station 7,The completed questionnaires to assess the effects of noise pollution in Yazd International Airport and the surrounding noise sensitive areas in 2014 by a portable audio device measurement is done. Results: The most amount of noise caused by aircraft traffic in the airport area and in adjacent areas with average noise level 84.8 dB at station No. 5 Regional Airport, located south of the airport, with an average noise level which was 75.5 dB. The results of analysis of questionnaires showed that 75 percent of people living in residential areas around the airport are being harassed by aircraft noise. Results indicate that, sleep disorders, nervousness, stress and mental illness and interfere with speech, regardless of the priority of different factors in the study area, are of the highest impact of aircraft noise. Conclusion: Aircraft noise is the strongest negative environmental factors that affect employees and residents around Yazd International Airport and can be harmful to health. The noise for health personnel, particularly those of daily tasks, are daily exposed to aircraft intense noise , are highly undesirable. So, essentially preventive severe conditions such as mandatory use of protective devices and soundproof acoustic shortening service personnel are needed for these people.

  18. Cross-cultural differences in color preferences: implication for international film distribution

    Science.gov (United States)

    Lee, Kyung Jae

    2002-06-01

    This paper proposes the necessity of manipulating colors of movie contents to fit diverse audiences around the world. Since films are highly color-dependent messages, it is critical to understand how people in different cultures respond differently to color. In recent years, the international market for filmed entertainment has grown more than the U.S. market. However, a lack of research on audience preferences shows no constant guide for the motion picture industry. The film production stage is often disregarded to deliver the appropriate visual color contents for local audience when U.S. films are distributed to foreign markets. Therefore, it is assumed that it would cause distractions for local audiences and it could result in poor ticket sales. When the U.S. produced films are distributed in Asia, colors of original films are always shown without manipulation. It is common that when a U.S. manufactured car is imported to Japan, a driver seat is installed on the right side and also other parts are modified for local customers. Film development is also significantly dependent on audience behavior, so film content also needs to be localized for the different culture. This paper will only address a hypothesis of the implementation of color marketing methodology present in motion pictures.

  19. Tissue distribution patterns of solubilized metals from internalized tungsten alloy in the F344 rat

    Directory of Open Access Journals (Sweden)

    Vernieda B. Vergara

    2016-06-01

    Full Text Available Because of its unique physical and chemical properties, tungsten has been increasingly utilized in a variety of civilian and military applications. This expanded use also raises the risk of human exposure through internalization by various routes. In most cases the toxicological and carcinogenic properties of these tungsten-based compounds are not known nor are the dissolution biokinetics and ultimate fate of the associated metals. Using a laboratory rodent model system designed to assess the health effects of embedded metals, and a tungsten alloy comprised of tungsten (91.1%, nickel (6.0%, and cobalt (2.9%, we investigated the tissue distribution patterns of the metals over a six month period. Despite its perceived insolubility, tungsten rapidly solubilized from the implanted metal fragments, as did nickel and cobalt. All three metals distributed systemically over time with extremely elevated levels of all three metals found in kidney, liver, and spleen. Unexpectedly, tungsten was found to cross the blood-brain and blood-testis barriers and localize in those tissues. These results, along with recent reports suggesting that tungsten is a tumor promoter, raises serious concerns as to the long-term health effects of exposure to tungsten and tungsten-based compounds.

  20. International and Domestic Sustainable Forest Management Policies: Distributive Effects on Power among State Agencies in Bangladesh

    Directory of Open Access Journals (Sweden)

    Lukas Giessen

    2016-04-01

    Full Text Available The last two decades of forest policy discussions have been dominated by calls for sustainable management of forest resources. Consequently, multiple international and domestic policies, supporting sustainable forest management (SFM, have evolved in numerous jurisdictions. Policies in developing countries often rely on foreign donors’ projects, which supplement domestic SFM policy. These policies assign various policy tasks to specific public bureaucracies, who then compete for these very tasks, as well as the related staff and budgets. Therefore, project and policy task assignment greatly influences bureaucratic power. This article analyzes the distributive effects of SFM policy on power (in terms of coercion, incentives and dominant information among relevant domestic and foreign donor bureaucracies in Bangladesh. Concepts from power theory, bureaucratic politics theory, and concepts of policy and policy process were combined to analyze 121 Bangladeshi SFM policies from 1992–2013, which assign a total of 1012 policy tasks to specific public bureaucracies. Using qualitative content analysis, inferences about power were assigned to specific competing bureaucracies by the totality of SFM policies made. Results identify domestic and foreign bureaucracies whose power distribution benefit most from the SFM policies viz. their competitors. It is concluded that bureaucracies gaining the most power set the limits and directions in designing, implementing and evaluating various elements of any national SFM policies.

  1. Preparation of ring-shaped composite bonded magnets with continuously controlled anisotropy distribution for internal space

    International Nuclear Information System (INIS)

    Yamashita, F; Yamada, O; Ohya, S; Kobayashi, O; Nakano, M; Fukunaga, H

    2010-01-01

    We have already reported an advanced method for producing a radially-anisotropic rare earth composite bonded magnet with continuously controlled direction of anisotropy. The magnet has been applied to an inner rotor as a practical usage. In this study, the outstanding preparation method was adopted into the preparation of a magnet applied for an outer rotor. An optimized condition of extrusion and compaction at an elevated temperature could be obtained. In addition, a low pressure configuration to the ring-shaped magnet from plural preformed magnets was carried out, which had specific distribution of magnetic anisotropy for internal space for a small motor, by using self recoverability based on the viscous deformation without an alignment field. No deterioration of magnetic properties was detected through the process even if those magnets were miniaturized. Resultantly, the (BH) max of a ring-shaped magnet with the continuously controlled direction of magnetic anisotropy attained the value of 186 kJ/m 3 , and we obtained sine-wave magnetic anisotropy distribution, even if those magnets were miniaturized.

  2. Accelerated Electromechanical Modeling of a Distributed Internal Combustion Engine Generator Unit

    Directory of Open Access Journals (Sweden)

    Serhiy V. Bozhko

    2012-07-01

    Full Text Available Distributed generation with a combustion engine prime mover is still widely used to supply electric power in a variety of applications. These applications range from backup power supply systems and combined wind-diesel generation to providing power in places where grid connection is either technically impractical or financially uneconomic. Modelling of such systems as a whole is extremely difficult due to the long-time load profiles needed and the computational difficulty of including small time-constant electrical dynamics with large time-constant mechanical dynamics. This paper presents the development of accelerated, reduced-order models of a distributed internal combustions engine generator unit. Overall these models are shown to achieve a massive improvement in the computational time required for long-time simulations while also achieving an extremely high level of dynamic accuracy. It is demonstrated how these models are derived, used and verified against benchmark models created using established techniques. Throughout the paper the modelling set as a whole, including multi level detail, is presented, detailed and finally summarised into a crucial tool for general system investigation and multiple target optimisation.

  3. Influence of phase transformations on the asymptotic residual stress distribution arising near a sharp V-notch tip

    International Nuclear Information System (INIS)

    Ferro, P

    2012-01-01

    In this work, the residual stress distribution induced by the solidification and cooling of a fusion zone in the vicinity of a sharp V-notch tip is investigated. The intensity of the residual asymptotic stress fields, quantified by the notch stress intensity factors, was studied for two different V-notch specimen geometries under generalized plane-strain conditions. In order to analyze the influence of phase transformations on the obtained results, simulations with and without the effects of phase transformation were carried out on ASTM SA 516 steel plates. Thanks to the possibilities of numerical modelling, additional analyses were performed without taking into account the transformation plasticity phenomenon. It was found that phase transformation effects (both volume change and transformation plasticity) have a great influence on the intensity and sign of the asymptotic stress fields at the sharp V-notch tips. This result is believed to be very important for the correct numerical determination (and future applications) of notch stress intensity factors resulting from asymptotic residual stress distributions induced by transient thermal loads. The analyses were performed with the finite element code SYSWELD. (paper)

  4. Effect of elliptic or circular holes on the stress distribution in plates of wood or plywood considered as orthotropic materials

    Science.gov (United States)

    C. B. Smith

    1944-01-01

    This is a mathematical analysis of the stress distribution existing near a hole in a wood or plywood plate subjected to tension, as, for example, near holes in the tension flanges of wood box beams. It is assumed that the strains are small and remain within the proportional limit. In this analysis a large, rectangular, orthotropic plate with a small elliptic hole at...

  5. Influence of prosthesis type and material on the stress distribution in bone around implants: A 3-dimensional finite element analysis

    Directory of Open Access Journals (Sweden)

    Gökçe Meriç

    2011-03-01

    Conclusions: Prosthesis design and materials affect the load-transmission mechanism. Although additional experimental and clinical studies are needed, FRC FPDs can be considered a suitable alternative treatment choice for implant-supported prostheses. Within the limitations of the study, the 3-unit FPD supported by 2 implants with a cantilevered extension revealed acceptable stress distributions.

  6. Acculturation, Acculturative Stress, and Depressive Symptoms in International Migrants: A Study with Vietnamese Women in South Korea.

    Science.gov (United States)

    Cho, Yong Ju; Jang, Yuri; Ko, Jung Eun; Lee, Sun Hae; Moon, Soo Kyung

    2017-10-10

    Globally, there have been increasing numbers of migrant women; these women are at an increased risk for depressive symptoms. The purpose of this study was to examine the associations among acculturation, acculturative stress and depressive symptoms in Vietnamese women who migrated to South Korea through marriages. We hypothesized that acculturative stress would serve as a mediator in the relationship between acculturation and depressive symptoms. Our findings from surveys with 217 Vietnamese immigrant women showed that the indirect effect of acculturation on depressive symptoms, mediated through acculturative stress [- .15 (.04)], was significant (bias corrected 95% confidence interval for the indirect effect = - .25, - .08). Low levels of acculturation increased acculturative stress, which in turn led to the elevated symptoms of depression. Our findings not only illuminate the adaptation processes of international, female migrants but also suggest avenues to protect and promote their mental well-being.

  7. Preschoolers’ Genetic, Physiological, and Behavioral Sensitivity Factors Moderate Links Between Parenting Stress and Child Internalizing, Externalizing, and Sleep Problems

    Science.gov (United States)

    Davis, Molly; Thomassin, Kristel; Bilms, Joanie; Suveg, Cynthia; Shaffer, Anne; Beach, Steven R. H.

    2017-01-01

    This study examined three potential moderators of the relations between maternal parenting stress and preschoolers’ adjustment problems: a genetic polymorphism - the short allele of the serotonin transporter (5-HTTLPR, ss/sl allele) gene, a physiological indicator - children’s baseline respiratory sinus arrhythmia (RSA), and a behavioral indicator - mothers’ reports of children’s negative emotionality. A total of 108 mothers (Mage = 30.68 years, SDage = 6.06) reported on their parenting stress as well as their preschoolers’ (Mage = 3.50 years, SDage = .51, 61% boys) negative emotionality and internalizing, externalizing, and sleep problems. Results indicated that the genetic sensitivity variable functioned according to a differential susceptibility model; however, the results involving physiological and behavioral sensitivity factors were most consistent with a diathesis-stress framework. Implications for prevention and intervention efforts to counter the effects of parenting stress are discussed. PMID:28295263

  8. Internal electric-field-lines distribution in CdZnTe detectors measured using X-ray mapping

    International Nuclear Information System (INIS)

    Bolotnikov, A.E.; Camarda, G.S.; Cui, Y.; Hossain, A.; Yang, G.; Yao, H.W.; James, R.B.

    2009-01-01

    The ideal operation of CdZnTe devices entails having a uniformly distributed internal electric field. Such uniformity especially is critical for thick long-drift-length detectors, such as large-volume CPG and 3-D multi-pixel devices. Using a high-spatial resolution X-ray mapping technique, we investigated the distribution of the electric field in real devices. Our measurements demonstrate that in thin detectors, 1 cm, with a large aspect ratio (thickness-to-width ratio), we observed two effects: the electric field lines bending away from or towards the side surfaces, which we called, respectively, the focusing field-line distribution and the defocusing field-line distribution. In addition to these large-scale variations, the field-line distributions were locally perturbed by the presence of extended defects and residual strains existing inside the crystals. We present our data clearly demonstrating the non-uniformity of the internal electric field

  9. Consensus statement on posttraumatic stress disorder from the International Consensus Group on Depression and Anxiety.

    Science.gov (United States)

    Ballenger, J C; Davidson, J R; Lecrubier, Y; Nutt, D J; Foa, E B; Kessler, R C; McFarlane, A C; Shalev, A Y

    2000-01-01

    To provide primary care clinicians with a better understanding of management issues in posttraumatic stress disorder (PTSD) and guide clinical practice with recommendations on the appropriate management strategy. The 4 members of the International Consensus Group on Depression and Anxiety were James C. Ballenger (chair), Jonathan R. T. Davidson, Yves Lecrubier, and David J. Nutt. Other faculty invited by the chair were Edna B. Foa, Ronald C. Kessler, Alexander C. McFarlane, and Arieh Y. Shalev. The consensus statement is based on the 6 review articles that are published in this supplement and the scientific literature relevant to the issues reviewed in these articles. Group meetings were held over a 2-day period. On day 1, the group discussed the review articles and the chair identified key issues for further debate. On day 2, the group discussed these issues to arrive at a consensus view. After the group meetings, the consensus statement was drafted by the chair and approved by all attendees. PTSD is often a chronic and recurring condition associated with an increased risk of developing secondary comorbid disorders, such as depression. Selective serotonin reuptake inhibitors are generally the most appropriate choice of first-line medication for PTSD, and effective therapy should be continued for 12 months or longer. The most appropriate psychotherapy is exposure therapy, and it should be continued for 6 months, with follow-up therapy as needed.

  10. Stress

    Science.gov (United States)

    ... taking care of an aging parent. With mental stress, the body pumps out hormones to no avail. Neither fighting ... with type 1 diabetes. This difference makes sense. Stress blocks the body from releasing insulin in people with type 2 ...

  11. Velocity and stress distributions of deep seismic zone under Izu-Bonin, Japan

    Science.gov (United States)

    Jiang, Guoming; Zhang, Guibin; Jia, Zhengyuan

    2017-04-01

    Deep earthquakes can provide the deep information of the Earth directly. We have collected the waveform data from 77 deep earthquakes with depth greater than 300 km under Izu-Bonin in Japan. To obtain the velocity structures of P- and S-wave, we have inversed the double-differences of travel times from deep event-pairs. These velocity anomalies can further yield the Poisson's ratio and the porosity. Our results show that the average P-wave velocity anomaly is lower 6%, however the S-wave anomaly is higher 2% than the iasp91 model. The corresponding Poisson's ratio and porosity anomaly are -24% and -4%, respectively, which suggest that the possibility of water in the deep seismic zone is very few and the porosity might be richer. To obtain the stress distribution, we have used the ISOLA method to analyse the non-double-couple components of moment tensors of 77 deep earthquakes. The focal mechanism results show that almost half of all earthquakes have larger double-couple (DC) components, but others have clear isotropic (ISO) or compensated linear vector dipole (CLVD) components. The non-double-couple components (ISO and CLVD) seem to represent the volume around a deep earthquake changes as it occurs, which could be explained the metastable olivine phase transition. All results indicate that the metastable olivine wedge (MOW) might exist in the Pacific slab under the Izu-Bonin region and the deep earthquakes might be induced by the phase change of metastable olivine.

  12. Vacuolar Chloride Fluxes Impact Ion Content and Distribution during Early Salinity Stress1

    Science.gov (United States)

    Baetz, Ulrike; Tohge, Takayuki; Martinoia, Enrico; De Angeli, Alexis

    2016-01-01

    The ability to control the cytoplasmic environment is a prerequisite for plants to cope with changing environmental conditions. During salt stress, for instance, Na+ and Cl− are sequestered into the vacuole to help maintain cytosolic ion homeostasis and avoid cellular damage. It has been observed that vacuolar ion uptake is tied to fluxes across the plasma membrane. The coordination of both transport processes and relative contribution to plant adaptation, however, is still poorly understood. To investigate the link between vacuolar anion uptake and whole-plant ion distribution during salinity, we used mutants of the only vacuolar Cl− channel described to date: the Arabidopsis (Arabidopsis thaliana) ALMT9. After 24-h NaCl treatment, almt9 knock-out mutants had reduced shoot accumulation of both Cl− and Na+. In contrast, almt9 plants complemented with a mutant variant of ALMT9 that exhibits enhanced channel activity showed higher Cl− and Na+ accumulation. The altered shoot ion contents were not based on differences in transpiration, pointing to a vacuolar function in regulating xylem loading during salinity. In line with this finding, GUS staining demonstrated that ALMT9 is highly expressed in the vasculature of shoots and roots. RNA-seq analysis of almt9 mutants under salinity revealed specific expression profiles of transporters involved in long-distance ion translocation. Taken together, our study uncovers that the capacity of vacuolar Cl− loading in vascular cells plays a crucial role in controlling whole-plant ion movement rapidly after onset of salinity. PMID:27503602

  13. Solid-solid phase transformation via internal stress-induced virtual melting, significantly below the melting temperature. Application to HMX energetic crystal.

    Science.gov (United States)

    Levitas, Valery I; Henson, Bryan F; Smilowitz, Laura B; Asay, Blaine W

    2006-05-25

    We theoretically predict a new phenomenon, namely, that a solid-solid phase transformation (PT) with a large transformation strain can occur via internal stress-induced virtual melting along the interface at temperatures significantly (more than 100 K) below the melting temperature. We show that the energy of elastic stresses, induced by transformation strain, increases the driving force for melting and reduces the melting temperature. Immediately after melting, stresses relax and the unstable melt solidifies. Fast solidification in a thin layer leads to nanoscale cracking which does not affect the thermodynamics or kinetics of the solid-solid transformation. Thus, virtual melting represents a new mechanism of solid-solid PT, stress relaxation, and loss of coherence at a moving solid-solid interface. It also removes the athermal interface friction and deletes the thermomechanical memory of preceding cycles of the direct-reverse transformation. It is also found that nonhydrostatic compressive internal stresses promote melting in contrast to hydrostatic pressure. Sixteen theoretical predictions are in qualitative and quantitative agreement with experiments conducted on the PTs in the energetic crystal HMX. In particular, (a) the energy of internal stresses is sufficient to reduce the melting temperature from 551 to 430 K for the delta phase during the beta --> delta PT and from 520 to 400 K for the beta phase during the delta --> beta PT; (b) predicted activation energies for direct and reverse PTs coincide with corresponding melting energies of the beta and delta phases and with the experimental values; (c) the temperature dependence of the rate constant is determined by the heat of fusion, for both direct and reverse PTs; results b and c are obtained both for overall kinetics and for interface propagation; (d) considerable nanocracking, homogeneously distributed in the transformed material, accompanies the PT, as predicted by theory; (e) the nanocracking does not

  14. Effect of internal tides in the distribution and abundance of microzooplankton in Todos Santos Bay (Ensenada, B.C.)

    Science.gov (United States)

    Valencia, A.; Ibañez Tejero, L.; Ladah, L. B.; Sanchez Velasco, L.; Barton, E. D.

    2016-02-01

    Microzooplankton trophically connects phytoplankton and zooplanktonic adults. Their distribution and abundance can be directly related to the inherent physical processes in the marine environment. In coastal waters, the distribution and transport of zooplankton, including microzooplankton, can be influenced by high frequency effects such as internal tides. To date, most of the work on planktonic organisms and their interaction with the internal tide has been focused on a few species, such as barnacles, bryozoans and crabs. The aim of this study was to determine the effect of internal tide on the vertical distribution and abundance of microzooplankton, with an emphasis on copepod nauplii, during the evolution of the internal tide in a summer period of strong thermal stratification. Samples were obtained by vertical plankton net (150 micron mesh) hauls at three depth strata (surface, mid-water and bottom in 25 m depth), independently, with a sampling frequency of every hour. The internal tide was detected by rapid changes in temperature and currents observed with thermistor chains and a bottom-mounted upward looking ADCP. Preliminary results shows a strong mode-1 baroclinic tidal signal. The highest abundance of copepod nauplii and microzooplankton biomass occurred at depth, associated with a strong tidal current. The abundance of copepod nauplii and the abundance of microzooplankton biomass in the surface and intermediate strata showed strong vertical displacements between both strata. Data suggest the vertical distribution of microzooplankton can be dependent on the internal tide.

  15. Overall bolt stress optimization

    DEFF Research Database (Denmark)

    Pedersen, Niels Leergaard

    2013-01-01

    The state of stress in bolts and nuts with International Organization for Standardization metric thread design is examined and optimized. The assumed failure mode is fatigue, so the applied preload and the load amplitude together with the stress concentrations define the connection strength....... Maximum stress in the bolt is found at the fillet under the head, at the thread start, or at the thread root. To minimize the stress concentration, shape optimization is applied. Nut shape optimization also has a positive effect on the maximum stress. The optimization results show that designing a nut......, which results in a more evenly distribution of load along the engaged thread, has a limited influence on the maximum stress due to the stress concentration at the first thread root. To further reduce the maximum stress, the transition from bolt shank to the thread must be optimized. Stress reduction...

  16. Stress distribution and displacement of maxillary anterior teeth during en-masse intrusion and retraction: A FEM study

    Directory of Open Access Journals (Sweden)

    Parag Bohara

    2017-01-01

    Full Text Available Background: Space closure by en masse intrusion and retraction in orthodontics is of particular interest. Aim: The aim of this study was to evaluate the stress distribution and displacement of maxillary anterior teeth. Materials and Methods: Four different finite element models of maxillary arch were constructed to understand the nature of stresses and displacement patterns of anterior teeth during en masse intrusion and retraction on force application with different combinations of mini-implants and retraction hooks. Results: In this study, tensile stresses were seen in the cervical region and various movements of teeth such as lingual crown tipping, bodily movement, lingual root tipping, intrusion, and extrusion were observed. Conclusion: Nature of stresses changes from tensile to compressive from cervical area to apical area. Various tooth displacements suggest that different combinations of mini-implants and retraction hooks affect the direction of the tooth movement.

  17. Evaluation of stress distribution of implant-retained mandibular overdenture with different vertical restorative spaces: A finite element analysis

    Science.gov (United States)

    Ebadian, Behnaz; Farzin, Mahmoud; Talebi, Saeid; Khodaeian, Niloufar

    2012-01-01

    Background: Available restorative space and bar height is an important factor in stress distribution of implant-supported overdentures. The purpose of this study was to evaluate the effect of different vertical restorative spaces and different bar heights on the stress distribution around implants by 3D finite element analysis. Materials and Methods: 3D finite element models were developed from mandibular overdentures with two implants in the interforaminal region. In these models, four different bar heights from gingival crest (0.5, 1, 1.5, 2 mm) with 15 mm occlusal plane height and three different occlusal plane heights from gingival crest (9, 12, 15 mm) with 2 mm bar height were analyzed. A vertical unilateral and a bilateral load of 150 N were applied to the central occlusal fossa of the first molar and the stress of bone around implant was analyzed by finite element analysis. Results: By increasing vertical restorative space, the maximum stress values around implants were found to be decreased in unilateral loading models but slightly increased in bilateral loading cases. By increasing bar height from gingival crest, the maximum stress values around implants were found to be increased in unilateral loading models but slightly decreased in bilateral loading cases. In unilateral loading models, maximum stress was found in a model with 9 mm occlusal plane height and 1.5 mm bar height (6.254 MPa), but in bilateral loading cases, maximum stress was found in a model with 15 mm occlusal plane height and 0.5 mm bar height (3.482 MPa). Conclusion: The reduction of bar height and increase in the thickness of acrylic resin base in implant-supported overdentures are biomechanically favorable and may result in less stress in periimplant bone. PMID:23559952

  18. A new method of residual stress distribution analysis for corroded Zircaloy-4 cladding

    International Nuclear Information System (INIS)

    Godlewski, J.; Cadalbert, R.

    1992-01-01

    An X-ray diffraction method of residual stress measurement is developed to determine the stress level in the metal near the metal/oxide interface of Zircaloy-4 cladding samples oxidized in steam water at 400degC under a pressure of 10.3 MPa. The stress gradient is obtained and the evolution of the average stress is determined as function of the oxidation time. The presence of tetragonal zirconia phase in quite large quantity near the metal/oxide interface could be correlated to the high stress level in the base metal, adjacent to the interface. (author)

  19. A new method for residual stress distribution - analysis of corroded zircaloy-4 cladding

    International Nuclear Information System (INIS)

    Godlewski, J.; Cadalbert, R.

    1992-01-01

    An X-ray diffraction method for residual stress measurement is developed to determine the stress level in the metal near the metal/oxide interface of Zircaloy-4 cladding samples oxidized in steam water at 400 deg C under a pressure of 10.3 MPa. The stress gradient is obtained and the evolution of the average stress is determined as a function of the oxidation time. The presence of tetragonal zirconia phase in quite large quantity near the metal/oxide interface could be correlated to the high stress level in the base metal, adjacent to the interface. 12 refs., 5 figs., 1 tab

  20. The effect of internal and external stress on two-way shape-memory behaviour in Co49Ni21.6Ga29.4 single crystals

    International Nuclear Information System (INIS)

    Liu, G D; Dai, X F; Luo, H Z; Liu, H Y; Meng, F B; Li, Y; Yu, X; Chen, J L; Wu, G H

    2011-01-01

    The effect of the internal stress on the two-way shape memory in Co 49 Ni 21.6 Ga 29.4 single crystals has been investigated. We found that the internal stress generated natively by the solidifying process works as a tensile force along the growth direction. Applying different compressive pre-stresses along the [0 0 1] direction, the shape-memory strain can be continuously changed from +1.0% to -2.3%. In the [1 1 0] direction, the strain monotonically increases from -2.0% to -4.0% due to a strong detwinning produced by the consistent effect of the external and internal stresses.

  1. The VIII International Congress on Stress Proteins in Biology and Medicine: täynnä henkeä.

    Science.gov (United States)

    Bonorino, Cristina; Sistonen, Lea; Eriksson, John; Mezger, Valérie; Santoro, Gabriella; Hightower, Lawrence E

    2018-03-01

    About 150 international scientists gathered in Turku, Finland, in August of 2017 for the eighth in a series of international congresses about the roles of stress proteins in biology and medicine. The scientific theme and title of the 2017 Congress was "Stress Management Mechanisms and Pathways." The meeting covered a broad range of topics, reflecting the wide scope of the Cell Stress Society International (CSSI) and highlighting the numerous recent breakthroughs in stress response biology and medicine. The keynote lecturers included Marja Jäättelä, Richard Morimoto, Anne Bertolotti, and Peter Walter. The Executive Council of the CSSI elected new Fellows and Senior Fellows. The Spirit of Budapest Award was presented to Peter Csermely, Wolfgang Schumann, and Subhash Lakhotia in recognition of pioneering service contributions to the CSSI. The CSSI Medallion for Career Achievement was awarded to Larry Hightower and CSSI president Gabriella Santoro proclaimed Tuesday, August 15, 2017, Robert M. Tanguay Day at the congress in recognition of Robert's many years of scientific accomplishment and work on behalf of the CSSI. Additional special events were the awarding of the Ferruccio Ritossa Early Career Award to Serena Carra and the Alfred Tissières Young Investigator Award to Ayesha Murshid. As is the tradition at CSSI congresses, there were social events that included an exciting piano performance by a trio of young Finnish pianists, at the Sibelius Museum.

  2. Academic stress and positive affect: Asian value and self-worth contingency as moderators among Chinese international students.

    Science.gov (United States)

    Liao, Kelly Yu-Hsin; Wei, Meifen

    2014-01-01

    The theoretical model proposed by Berry and colleagues (Berry, 1997; Berry, Kim, Minde, & Mok, 1987) highlights the importance of identifying moderators in the acculturation process. Accordingly, the current study examined the Asian cultural value of family recognition through achievement (FRTA) and contingency of self-worth on academic competence (CSW-AC) as moderators in the association between academic stress and positive affect among Chinese international students. A total of 370 Chinese international students completed online surveys. Results from a hierarchical regression indicated that while academic stress was negatively associated with positive affect, FRTA was positively associated with positive affect. In other words, those with high academic stress reported a lower level of positive affect. However, individuals who endorsed high levels of FRTA reported a higher level of positive affect. In addition, results also revealed a significant interaction between academic stress and CSW-AC on positive affect. Thus, the study's finding supported the moderator role of CSW-AC. Simple effect analyses were conducted to examine the significant interaction. The results showed that higher levels of CSW-AC strengthened the negative association between academic stress and positive affect but lower levels of CSW-AC did not. Future research directions and implications are discussed.

  3. Relationship between parenting stress and informant discrepancies on symptoms of ADHD/ODD and internalizing behaviors in preschool children

    Science.gov (United States)

    Ni, Hsing-Chang; Liang, Sophie Hsin-Yi; Lin, Hsiang-Yuan; Lin, Chiao-Fan; Tseng, Yu-Han

    2017-01-01

    Parent and teacher ratings of child behaviors are often discrepant, and these discrepancies may be correlated with parenting stress. The present study explored whether various parenting stress factors are associated with discrepancies between parent and teacher ratings of attention-deficit/hyperactivity disorder and oppositional defiant disorder (ODD) as well as internalizing symptoms in preschool children. We recruited 299 Taiwanese preschool children (aged 4–6 years) from the community or via clinical referrals. A structural equation modeling was used to analyze the relationships among three factors derived from the Parenting Stress Index-Short Form and informant discrepancies on symptoms of inattention, hyperactivity/impulsivity, ODD, and internalizing behaviors. Scores reported by parents were higher for each of the symptoms examined than those reported by teachers, and the degree of agreement between informants ranged from low to moderate. The parental distress factor of parenting stress was associated only with parent ratings, whereas other factors of parenting stress—parent-child dysfunctional interaction and parents’ stress resulted from their child’s temperament—were correlated with both parent and teacher ratings. Only parental distress factor predicted informant discrepancies for all behavioral symptoms assessed. Our findings suggest that parental distress should be considered when parent rating scores show significant discrepancies from that of teacher rating scores. PMID:29016602

  4. A database to evaluate stress intensity factors of elbows with throughwall flaws under combined internal pressure and bending moment

    International Nuclear Information System (INIS)

    Chattopadhyay, J.; Dutta, B.K.; Kushwaha, H.S.; Mahajan, S.C.; Kakodkar, A.

    1993-01-01

    The advent of Leak-Before-Break (LBB) concept has replaced the traditional design basis event of Double Ended Guillotine Break (DEGB) in the design of primary heat transport (PHT) piping. The use of LBB concept requires postulation of largest credible cracks at highly stressed locations and demonstration of its stability under the maximum credible loading conditions. Stress analysis of PHT piping in nuclear power plants shows that the highly stressed piping components are normally elbows and branch tees. This necessitates detailed fracture mechanics evaluation of piping connections by computing Stress Intensity Factor (SIF) and/or J-integral. Simple analytical solutions for evaluation of SIF and J-integral for cracks in straight pipes are readily available in literature. However, the same type of solutions for elbows and tees are limited in open literature. In the present work, a database is generated to evaluate SIF for throughwall circumferential and longitudinal cracks under combined internal pressure and bending moment. Different parameters to characterise a cracked elbow are pipe factor (h), pipe bore radius to thickness ratio (r/t) and crack length. Another parameter (σ) is used to consider the relative magnitude of stresses due to internal pressure and remote bending moment. The database has been used to derive closed form expressions to evaluate SIF for elbow with cracks in terms of the aforementioned parameters. (author). 8 refs., 12 figs., 3 tabs

  5. Experimental investigation of localized stress-induced leakage current distribution in gate dielectrics using array test circuit

    Science.gov (United States)

    Park, Hyeonwoo; Teramoto, Akinobu; Kuroda, Rihito; Suwa, Tomoyuki; Sugawa, Shigetoshi

    2018-04-01

    Localized stress-induced leakage current (SILC) has become a major problem in the reliability of flash memories. To reduce it, clarifying the SILC mechanism is important, and statistical measurement and analysis have to be carried out. In this study, we applied an array test circuit that can measure the SILC distribution of more than 80,000 nMOSFETs with various gate areas at a high speed (within 80 s) and a high accuracy (on the 10-17 A current order). The results clarified that the distributions of localized SILC in different gate areas follow a universal distribution assuming the same SILC defect density distribution per unit area, and the current of localized SILC defects does not scale down with the gate area. Moreover, the distribution of SILC defect density and its dependence on the oxide field for measurement (E OX-Measure) were experimentally determined for fabricated devices.

  6. Distribution of 137Cs in Meat and Internal Organs of Wild Boar

    International Nuclear Information System (INIS)

    Babic, D.; Marovic, G.; Skoko, B.; Vickovic, I.

    2013-01-01

    Wild boar (Sus scrofa) is one of the most common species of game on the territory of Croatia. Similarly to other game, it can accumulate fission products more effectively than domestic animals. Therefore, it is a good biondicator for radioactive contamination of ecosystems. The purpose of our research has been to investigate current radioactive contamination of wild boars by 137Cs and its distribution inside the animal body. Therefore, during the winter of 2009 and summer of 2010, we collected samples of meat, internal organs (heart, lungs, spleen, kidney and liver) and bones from 11 animals. All the animals were from the area of the research locality S umbar . The average activity concentration of 137Cs found in meat samples was (1.47 ± 0.01) Bqkg -1 , and in bones (0.12 ± 0.01) Bqkg -1 . Activity concentration found in organs was (in ascending order): lungs (1.63 ± 0.01) Bqkg -1 , spleen (2.29 ± 0.04) Bqkg -1 , liver (2.54 ± 0.02) Bqkg -1 , heart (2.70 ± 0.02) Bqkg -1 , and kidney (3.18 ± 0.06) Bqkg -1 . We also calculated the values of the ratio of activity concentrations in internal organs and meat. Comparison of the obtained values with those for samples collected after the Chernobyl accident shows that the present ones are higher for liver and kidney, while those for heart are almost the same. Since vital organs of wild boars are more loaded than meat and bones, the impact of radioactive contamination on health of these animals should be more closely investigated. Also, these results imply that kidney is the most accumulating organ for 137Cs.(author)

  7. Collection and presentation of animal data relating to internally distributed radionuclides

    International Nuclear Information System (INIS)

    Lathrop, K.A.

    1981-01-01

    Data obtained from laboratory animals on the distribution of an internally administered radionuclide may be put to use by various people in ways quite different from the one for which the original observations were made. Consideration for these other scientists, sometimes in unrelated fields, can be shown by attention to a few details in the method of data collection and reporting that may improve the author's credibility, the reader's comprehension, and the value of the data. Briefly stated, two rules should be followed: Account for 100% of the administered radioactivity; and report data as fraction of administered activity per organ. The first rule serves as an internal check on the proper functioning of counting equipment, and may disclose excretion, contamination of counting tubes, or failure to inject the desired amount of activity. The second rule allows anyone to make use of the raw data. Presentation of the data only in complicated, manipulated form either totally prevents reconstruction of the raw data, or demands tedious, uncertain conversions. Examples of such manipulated data include percent dose per gram per 1% body weight and percent kilogram dose per gram. At the other extreme in reporting data for radioactivity, and to be equally avoided, are completely unprocessed values, such as counts per minute, with no reference made to the number of counts injected or to the time lapse between counts. Adherence to these two principles will permit the reader to follow through on any permutations of the data that the author may make, and to apply the data in unrelated situations

  8. Welding residual stress improvement in internal components by water jet peening

    International Nuclear Information System (INIS)

    Enomoto, K.; Hirano, K.; Hayashi, M.; Hayashi, E.

    1996-01-01

    Cavitations are generated when highly pressurized water is jetted in water. Surface residual stress is improved remarkably due to the peening effect of extremely high pressure caused by the collapse of cavitation bubbles. This technique is called water jet peening (WJP). WJP is expected to be an effective maintenance technique for the prevention of stress corrosion cracking caused by residual stress in various components of power generating plants. Various kinds of specimens were water jet peened to evaluate the fundamental characteristics of WJP and to select the most appropriate conditions for the residual stress improvement. Test results showed that WJP markedly improved the tensile residual stress caused by welding and grinding to the high compressive residual stress and seems to prevent the stress corrosion cracking

  9. Stress at the Korean Mountains: meeting report of the 8th International Workshop on the Molecular Biology of Stress Responses

    OpenAIRE

    De Maio, Antonio; Tanguay, Robert M.; Kampinga, Harm; Lee, Eunil; Kim, Chang Duck; Hightower, Lawrence

    2010-01-01

    South Korea is a country exemplified by a combination of upscale new technology and ancient mysticism. The busy streets of Seoul hustle and bustle like any large, active metropolis, yet the city's inhabitants radiate an intrinsic sense of peace, creating a timeless atmosphere. The combination of emerging technology and profound respect for the Korean culture and heritage makes this country a unique environment in which to organize a successful scientific meeting. Cell Stress Society Internati...

  10. Study of temperature distribution of pipes heated by moving rectangular gauss distribution heat source. Development of pipe outer surface irradiated laser stress improvement process (L-SIP)

    International Nuclear Information System (INIS)

    Ohta, Takahiro; Kamo, Kazuhiko; Asada, Seiji; Terasaki, Toshio

    2009-01-01

    The new process called L-SIP (outer surface irradiated Laser Stress Improvement Process) is developed to improve the tensile residual stress of the inner surface near the butt welded joints of pipes in the compression stress. The temperature gradient occurs in the thickness of pipes in heating the outer surface rapidly by laser beam. By the thermal expansion difference between the inner surface and the outer surface, the compression stress occurs near the inner surface of pipes. In this paper, the theoretical equation for the temperature distributions of pipes heated by moving rectangular Gauss distribution heat source on the outer surface is derived. The temperature histories of pipes calculated by theoretical equation agree well with FEM analysis results. According to the theoretical equation, the controlling parameters of temperature distributions and histories are q/2a y , vh, a x /h and a y /h, where q is total heat input, a y is heat source length in the axial direction, a x is Gaussian radius of heat source in the hoop direction, ν is moving velocity, and h is thickness of the pipe. The essential variables for L-SIP, which are defined on the basis of the measured temperature histories on the outer surface of the pipe, are Tmax, F 0 =kτ 0 /h 2 , vh, W Q and L Q , where Tmax is maximum temperature on the monitor point of the outer surface, k is thermal diffusivity coefficient, τ 0 is the temperature rise time from 100degC to maximum temperature on the monitor point of the outer surface, W Q is τ 0 x ν, and L Q is the uniform temperature length in the axial direction. It is verified that the essential variables for L-SIP match the controlling parameters by the theoretical equation. (author)

  11. Finite element analysis of the stress distributions in peri-implant bone in modified and standard-threaded dental implants

    Directory of Open Access Journals (Sweden)

    Serkan Dundar

    2016-01-01

    Full Text Available The aim of this study was to examine the stress distributions with three different loads in two different geometric and threaded types of dental implants by finite element analysis. For this purpose, two different implant models, Nobel Replace and Nobel Active (Nobel Biocare, Zurich, Switzerland, which are currently used in clinical cases, were constructed by using ANSYS Workbench 12.1. The stress distributions on components of the implant system under three different static loadings were analysed for the two models. The maximum stress values that occurred in all components were observed in FIII (300 N. The maximum stress values occurred in FIII (300 N when the Nobel Replace implant is used, whereas the lowest ones, in the case of FI (150 N loading in the Nobel Active implant. In all models, the maximum tensions were observed to be in the neck region of the implants. Increasing the connection between the implant and the bone surface may allow more uniform distribution of the forces of the dental implant and may protect the bone around the implant. Thus, the implant could remain in the mouth for longer periods. Variable-thread tapered implants can increase the implant and bone contact.

  12. Stress distribution at the dissimilar metal weld of safety injection nozzle according to safe-end length and SMW thickness

    International Nuclear Information System (INIS)

    Kim, Tae Jin; Jeong, Woo Chul; Huh, Nam Su

    2015-01-01

    In the present paper, we evaluate the effects of the safe-end length and thickness of the similar metal weld (SMW) of safety injection nozzles on stress distributions at the dissimilar metal weld (DMW). For this evaluation, we carry out detailed 2-D axisymmetric finite element analyses by considering four different values of the safe-end length and four different values of the thickness of SMW. Based on the results obtained, we found that the SMW thickness affects the axial stresses at the center of the DMW for the shorter safe-end length; on the other hand, it does not affect the hoop stresses. In terms of the safe-end length, the values of the axial and hoop stresses at the inner surface of the DMW center increase as the safe-end length increases. In particular, for the cases considered in the present study, the stress distributions at the DMW center can be categorized according to certain values of safe-end length

  13. The role of prosthetic abutment material on the stress distribution in a maxillary single implant-supported fixed prosthesis

    International Nuclear Information System (INIS)

    Peixoto, Hugo Eduardo; Bordin, Dimorvan; Del Bel Cury, Altair A.; Silva, Wander José da; Faot, Fernanda

    2016-01-01

    Purpose: Evaluate the influence of abutment's material and geometry on stress distribution in a single implant-supported prosthesis. Materials and Methods: Three-dimensional models were made based on tomographic slices of the upper middle incisor area, in which a morse taper implant was positioned and a titanium (Ti) or zirconia (ZrN) universal abutments was installed. The commercially available geometry of titanium (T) and zirconia (Z) abutments were used to draw two models, TM1 and ZM1 respectively, which served as control groups. These models were compared with 2 experimental groups were the mechanical properties of Z were applied to the titanium abutment (TM2) and vice versa for the zirconia abutment (ZM2). Subsequently, loading was simulated in two steps, starting with a preload phase, calculated with the respective friction coefficients of each materials, followed by a combined preload and chewing force. The maximum von Mises stress was described. Data were analyzed by two-way ANOVA that considered material composition, geometry and loading (p 0.05). Conclusion: The screw was the piece most intensely affected, mainly through the preload force, independent of the abutment's material. - Highlights: • The abutment's screw was the most impaired piece of the dental implant system. • The highest stress was located at first thread of the abutment's screw. • The preload is the main factor in the abutment's screw stress. • Abutment configuration and material can have a positive contribution for the stress distribution

  14. Composite resin reinforced with pre-tensioned fibers: a three-dimensional finite element study on stress distribution.

    Science.gov (United States)

    Jie, Lin; Shinya, Akikazu; Lassila, Lippo V J; Vallittu, Pekka K

    2013-01-01

    Pre-tensioned construction material is utilized in engineering applications of high strength demands. The purpose of this study was to evaluate the effect of the pre-tensioning fibers of fiber-reinforced composite (FRC) using three-dimensional finite element (FE) analysis. The 3D FE models of particulate composite resin (CR), FRC and composite resin reinforced with pre-tensioned fibers (PRE-T-FRC) were constructed. The uniaxial three-point bending test was simulated using FE analysis to calculate the principal stress distribution. In the FRC and PRE-T-FRC, stresses were higher than CR, and they were located in the fiber. However, the maximum principal stress value at the composite of PRE-T-FRC was lower than the FRC and CR. Composite resin reinforced with pre-tensioned fibers was advantageous for stress distribution and lowering the stress at the composite itself. Experimental studies on physical properties of pre-tensioned FRC are encouraged to be conducted.

  15. Finite Element Analysis of the Effect of Superstructure Materials and Loading Angle on Stress Distribution around the Implant

    Directory of Open Access Journals (Sweden)

    Jafari K

    2014-12-01

    Full Text Available Statement of Problem: A general process in implant design is to determine the reason of possible problems and to find the relevant solutions. The success of the implant depends on the control technique of implant biomechanical conditions. Objectives: The goal of this study was to evaluate the influence of both abutment and framework materials on the stress of the bone around the implant by using threedimensional finite element analysis. Materials and Methods: A three-dimensional model of a patient’s premaxillary bone was fabricated using Cone Beam Computed Tomography (CBCT. Then, three types of abutment from gold, nickel-chromium and zirconia and also three types of crown frame from silver-palladium, nickel-chromium and zirconia were designed. Finally, a 178 N force at angles of zero, 30 and 45 degrees was exerted on the implant axis and the maximum stress and strain in the trabecular, cortical bones and cement was calculated. Results: With changes of the materials and mechanical properties of abutment and frame, little difference was observed in the level and distribution pattern of stress. The stress level was increased with the rise in the angle of pressure exertion. The highest stress concentration was related to the force at the angle of 45 degrees. The results of the cement analysis proved an inverse relationship between the rate of elastic modulus of the frame material and that of the maximum stress in the cement. Conclusions: The impact of the angle at which the force was applied was more significant in stress distribution than that of abutment and framework core materials.

  16. Iodine stress corrosion cracking (SCC) of unirradiated Zircaloy-4 tubing by means of internal gas pressurization, (1)

    International Nuclear Information System (INIS)

    Onchi, Takeo; Inoue, Tadashi

    1982-01-01

    The internal gas pressurization tests were conducted at 360 0 C, to examine the influence of iodine concentration on the iodine stress corrosion cracking (SCC) susceptibility of Zircaloy-4 tubing of 17 x 17 type PWR design. The iodine contents studied were ranging of 0.06 to 6 mg/cm 2 , corresponding to 30 from 0.3 mg/cm 3 . Applied hoop stress vs. time-to-failure relationships were obtained in argon gas with iodine, as well as without iodine, from the tests of maximum holding times up to 72 hrs. The relationships obtained were insensitive to iodine contents. The applied stress lowering in iodine atmosphere approached a threshold stress below which SCC failure did not occur within the holding time, but not in argon gas alone. The threshold stresses were approximately 25.5 kg/mm 2 (250 Mpa), independent on iodine concentrations. Based on fracture mechanics approach and fractographic analysis, an interpretation was made of those applied stress and time-to-failure relationships. (author)

  17. FEM Modeling of In-Plane Stress Distribution in Thick Brittle Coatings/Films on Ductile Substrates Subjected to Tensile Stress to Determine Interfacial Strength.

    Science.gov (United States)

    Wang, Kaishi; Zhang, Fangzhou; Bordia, Rajendra K

    2018-03-27

    The ceramic-metal interface is present in various material structures and devices that are vulnerable to failures, like cracking, which are typically due to their incompatible properties, e.g., thermal expansion mismatch. In failure of these multilayer systems, interfacial shear strength is a good measure of the robustness of interfaces, especially for planar films. There is a widely-used shear lag model and method by Agrawal and Raj to analyse and measure the interfacial shear strength of thin brittle film on ductile substrates. The use of this classical model for a type of polymer derived ceramic coatings (thickness ~18 μm) on steel substrate leads to high values of interfacial shear strength. Here, we present finite element simulations for such a coating system when it is subjected to in-plane tension. Results show that the in-plane stresses in the coating are non-uniform, i.e., varying across the thickness of the film. Therefore, they do not meet one of the basic assumptions of the classical model: uniform in-plane stress. Furthermore, effects of three significant parameters, film thickness, crack spacing, and Young's modulus, on the in-plane stress distribution have also been investigated. 'Thickness-averaged In-plane Stress' (TIS), a new failure criterion, is proposed for estimating the interfacial shear strength, which leads to a more realistic estimation of the tensile strength and interfacial shear strength of thick brittle films/coatings on ductile substrates.

  18. Neutron diffraction study of internal stresses in brazed CFC/Mo divertor structures for NET/ITER

    Energy Technology Data Exchange (ETDEWEB)

    Ceretti, M [Laboratoire Leon-Brillouin, CEA/CE Saclay, F-91191, Gif-sur-Yvette (France); Coppola, R [ENEA/Casaccia, INN-FIS, C.P. 2400, I-00100 Rome (Italy); Di Pietro, E [ENEA/Frascati, Dip. FUS, C.P. 2400, I-00100 Rome (Italy); Lodini, A [Laboratoire Leon-Brillouin, CEA/CE Saclay, F-91191, Gif-sur-Yvette (France) Universite de Champagne-Ardennes, Reims (France); Perrin, M [Laboratoire Leon-Brillouin, CEA/CE Saclay, F-91191, Gif-sur-Yvette (France); Piant, A [Laboratoire Leon-Brillouin, CEA/CE Saclay, F-91191, Gif-sur-Yvette (France); Rustichelli, F [Istituto di Scienze Fisiche, Universita di Ancona (Italy)

    1994-09-01

    This contribution presents the first results of a study, performed by neutron diffraction, on the internal stresses remaining after brazing at 860 C in graphite/molybdenum samples developed for NET/ITER. Samples of polycrystalline graphite and a carbon-fiber composite are considered. The deformation field is characterized close to the brazing interface, within a linear spatial resolution of approximately 2 mm. The results are discussed with reference to those obtainable by other methods and to theoretical considerations. ((orig.))

  19. Effect of Integration Patterns Around Implant Neck on Stress Distribution in Peri-Implant Bone: A Finite Element Analysis.

    Science.gov (United States)

    Han, Jingyun; Sun, Yuchun; Wang, Chao

    2017-08-01

    To investigate the biomechanical performance of different osseointegration patterns between cortical bone and implants using finite element analysis. Fifteen finite element models were constructed of the mandibular fixed prosthesis supported by implants. Masticatory loads (200 N axial, 100 N oblique, 40 N horizontal) were applied. The cortical bone/implant interface was divided equally into four layers: upper, upper-middle, lower-middle, and lower. The bone stress and implant displacement were calculated for 5 degrees of uniform integration (0, 20%, 40%, 60%, and 100%) and 10 integration patterns. The stress was concentrated in the bone margin and gradually decreased as osseointegration progressed, when the integrated and nonintegrated areas were alternated on the bone-implant surface. Compared with full integration, the integration of only the lower-middle layer or lower half layers significantly decreased von Mises, tensile, and compressive stresses in cortical bone under oblique and horizontal loads, and these patterns did not induce higher stress in the cancellous bone. For the integration of only the upper or upper-middle layer, stress in the cortical and cancellous bones significantly increased and was considerably higher than in the case of nonintegration. In addition, the maximum stress in the cortical bone was sensitive to the quantity of integrated nodes at the bone margin; lower quantity was associated with higher stress. There was no significant difference in the displacement of implants among 15 models. Integration patterns of cortical bone significantly affect stress distribution in peri-implant bone. The integration of only the lower-middle or lower half layers helps to increase the load-bearing capacity of peri-implant bone and decrease the risk of overloading, while upper integration may further increase the risk of bone resorption. © 2016 by the American College of Prosthodontists.

  20. A Distributed Computing Framework for Real-Time Detection of Stress and of Its Propagation in a Team.

    Science.gov (United States)

    Pandey, Parul; Lee, Eun Kyung; Pompili, Dario

    2016-11-01

    Stress is one of the key factor that impacts the quality of our daily life: From the productivity and efficiency in the production processes to the ability of (civilian and military) individuals in making rational decisions. Also, stress can propagate from one individual to other working in a close proximity or toward a common goal, e.g., in a military operation or workforce. Real-time assessment of the stress of individuals alone is, however, not sufficient, as understanding its source and direction in which it propagates in a group of people is equally-if not more-important. A continuous near real-time in situ personal stress monitoring system to quantify level of stress of individuals and its direction of propagation in a team is envisioned. However, stress monitoring of an individual via his/her mobile device may not always be possible for extended periods of time due to limited battery capacity of these devices. To overcome this challenge a novel distributed mobile computing framework is proposed to organize the resources in the vicinity and form a mobile device cloud that enables offloading of computation tasks in stress detection algorithm from resource constrained devices (low residual battery, limited CPU cycles) to resource rich devices. Our framework also supports computing parallelization and workflows, defining how the data and tasks divided/assigned among the entities of the framework are designed. The direction of propagation and magnitude of influence of stress in a group of individuals are studied by applying real-time, in situ analysis of Granger Causality. Tangible benefits (in terms of energy expenditure and execution time) of the proposed framework in comparison to a centralized framework are presented via thorough simulations and real experiments.

  1. Nonlocal approach to the analysis of the stress distribution in granular systems. II. Application to experiment

    International Nuclear Information System (INIS)

    Scott, J.E.; Kenkre, V.M.; Hurd, A.J.

    1998-01-01

    A theory of stress propagation in granular materials developed recently [Kenkre, Scott, Pease, and Hurd, preceding paper, Phys. Rev. E 57, 5841 (1998)] is applied to the compaction of ceramic and metal powders in pipes with previously unexplained experimental features such as nonmonotonic density and stress variation along the axis of cylindrical compacts. copyright 1998 The American Physical Society

  2. Stress distribution in a semi-infinite body symmetrically loaded over a circular area

    Science.gov (United States)

    Mcginness, H.

    1980-01-01

    Algorithms are developed for computing stresses in a semi-infinite body when loaded by a uniform pressure acting over a circular area. The algorithm allows easy determination of any stress component in a semi-infinite body having a known Poisson's ratio. Example curves are plotted for Portland cement grout and metal representative values.

  3. Nonlocal approach to the analysis of the stress distribution in granular systems. II. Application to experiment

    Science.gov (United States)

    Scott, J. E.; Kenkre, V. M.; Hurd, A. J.

    1998-05-01

    A theory of stress propagation in granular materials developed recently [Kenkre, Scott, Pease, and Hurd, preceding paper, Phys. Rev. E 57, 5841 (1998)] is applied to the compaction of ceramic and metal powders in pipes with previously unexplained experimental features such as nonmonotonic density and stress variation along the axis of cylindrical compacts.

  4. Male Asian international students' perceived racial discrimination, masculine identity, and subjective masculinity stress: a moderated mediation model.

    Science.gov (United States)

    Wong, Y Joel; Tsai, Pei-Chun; Liu, Tao; Zhu, Qingqing; Wei, Meifen

    2014-10-01

    This study examined male Asian international college students' perceptions of racial discrimination, subjective masculinity stress, centrality of masculine identity, and psychological distress by testing a moderated mediation model. Participants were 160 male Asian international college students from 2 large public universities. Participants' perceived racial discrimination was positively related to their subjective masculinity stress only at high (but not low) levels of masculine identity centrality. Additionally, subjective masculinity stress was positively related to psychological distress, although this association was stronger among those who reported high levels of masculine identity centrality. The authors also detected a moderated mediation effect in which subjective masculinity stress mediated the relationship between perceived racial discrimination and psychological distress only at high (but not low) levels of masculine identity centrality. These findings contribute to the counseling psychology literature by highlighting the connections between race- and gender-related stressors as well as the relevance of masculine identity to an understanding of men's mental health. PsycINFO Database Record (c) 2014 APA, all rights reserved.

  5. The distribution of wall shear stress downstream of a change in roughness

    International Nuclear Information System (INIS)

    Loureiro, J.B.R.; Sousa, F.B.C.C.; Zotin, J.L.Z.; Silva Freire, A.P.

    2010-01-01

    In the present work, six different experimental techniques are used to characterize the non-equilibrium flow downstream of a rough-to-smooth step change in surface roughness. Over the rough surface, wall shear stress results obtained through the form drag and the Reynolds stress methods are shown to be mutually consistent. Over the smooth surface, reference wall shear stress data is obtained through two optical methods: linear velocity profiles obtained through laser-Doppler anemometry and a sensor surface, the diverging fringe Doppler sensor. The work shows that the two most commonly used methods to determine the wall shear stress, the log-law gradient method and the Reynolds shear stress method, are completely inappropriate in the developing flow region. Preston tubes, on the other hand, are shown to perform well in the region of a non-equilibrium flow.

  6. Tunable superstructure fiber Bragg grating with chirp-distribution modulation based on the effect of external stress.

    Science.gov (United States)

    Huang, Yize; Li, Yi; Zhu, Huiqun; Tong, Guoxiang; Fang, Baoying; Li, Liu; Shen, Yujian; Zheng, Qiuxin; Liang, Qian; Yan, Meng; Wang, Feng; Qin, Yuan; Ding, Jie; Wang, Xiaohua

    2012-09-15

    We report an external stress modulation method for producing a superstructure fiber Bragg grating (FBG) with approximate cascaded resonant cavities composed of different index chirp distributions. The 15 mm uncoated apodized uniform-period FBG is pressed by the vertical stress from the upper 11 pieces of the pattern plate controlled by a piezoelectric ceramic actuator. The piece length is 1 mm, and the interval of the adjacent pieces is 0.4 mm. The reflectivity of the modulated FBG gradually shows six obvious multichannel 75%-85% reflection peaks with the increase of the vertical stress of each pattern-plate piece from 0 to 30 N. The channel spacing is steady at about 10 GHz for a C-band wavelength division multiplexing system.

  7. Finite element analysis to determine the stress distribution, displacement and safety factor on a microplate for the fractured jaw case

    Science.gov (United States)

    Pratama, Juan; Mahardika, Muslim

    2018-03-01

    Microplate is a connecting plate that can be used for jaw bone fixation. In the last two decades, microplate has been used so many times to help reconstruction of fractured jaw bone which is called mandibular bone or mandible bone. The plate is used to provide stable fixation of the fractured bone tissue during healing and reconstruction process. In this study Finite Element Analysis was used to predict the stress concentration and distribution on a microplate, displacement on the microplate and also to determine the safety factor of the microplate based on maximum allowable stress value, and finally to ascertain whether microplate is safe to use or not. The microplate was produced from punching process using titanium grade 1 (pure titanium) as material with a thickness of 500 µm. The results of the research indicated that the microplate was safe to use according to the maximum stress around the hole, displacement around the hole and also the safety factor of the microplate.

  8. A prediction method of temperature distribution and thermal stress for the throttle turbine rotor and its application

    Directory of Open Access Journals (Sweden)

    Yang Yu

    2017-01-01

    Full Text Available In this paper, a prediction method of the temperature distribution for the thermal stress for the throttle-regulated steam turbine rotor is proposed. The rotor thermal stress curve can be calculated according to the preset power requirement, the operation mode and the predicted critical parameters. The results of the 660 MW throttle turbine rotor show that the operators are able to predict the operation results and to adjust the operation parameters in advance with the help of the inertial element method. Meanwhile, it can also raise the operation level, thus providing the technical guarantee for the thermal stress optimization control and the safety of the steam turbine rotor under the variable load operation.

  9. Temperature and blood flow distribution in the human leg during passive heat stress.

    Science.gov (United States)

    Chiesa, Scott T; Trangmar, Steven J; González-Alonso, José

    2016-05-01

    The influence of temperature on the hemodynamic adjustments to direct passive heat stress within the leg's major arterial and venous vessels and compartments remains unclear. Fifteen healthy young males were tested during exposure to either passive whole body heat stress to levels approaching thermal tolerance [core temperature (Tc) + 2°C; study 1; n = 8] or single leg heat stress (Tc + 0°C; study 2; n = 7). Whole body heat stress increased perfusion and decreased oscillatory shear index in relation to the rise in leg temperature (Tleg) in all three major arteries supplying the leg, plateauing in the common and superficial femoral arteries before reaching severe heat stress levels. Isolated leg heat stress increased arterial blood flows and shear patterns to a level similar to that obtained during moderate core hyperthermia (Tc + 1°C). Despite modest increases in great saphenous venous (GSV) blood flow (0.2 l/min), the deep venous system accounted for the majority of returning flow (common femoral vein 0.7 l/min) during intense to severe levels of heat stress. Rapid cooling of a single leg during severe whole body heat stress resulted in an equivalent blood flow reduction in the major artery supplying the thigh deep tissues only, suggesting central temperature-sensitive mechanisms contribute to skin blood flow alone. These findings further our knowledge of leg hemodynamic responses during direct heat stress and provide evidence of potentially beneficial vascular alterations during isolated limb heat stress that are equivalent to those experienced during exposure to moderate levels of whole body hyperthermia. Copyright © 2016 the American Physiological Society.

  10. Increasing Aridity is Enhancing Silver Fir (Abies Alba Mill). Water Stress in its South-Western Distribution Limit

    Energy Technology Data Exchange (ETDEWEB)

    Macias, M. [Department of Geology, University of Helsinki, Gustaf Haellstroeminkatu 2, P.O. Box 64, FI-00014 Helsinki (Finland); Andreu, L.; Bosch, O.; Gutierrez, E. [Departament d' Ecologia, Universitat de Barcelona, Avgda. Diagonal, 645, Barcelona, 08028, Catalonia (Spain); Camarero, J.J. [Unidad de Recursos Forestales, Centro de Investigacion Agroalimentaria, Gobierno de Aragon, Apdo. 727, Zaragoza, 50080, Aragon (Spain)

    2006-12-15

    Tree populations located at the geographical distribution limit of the species may provide valuable information about the response of tree growth to climate warming across climatic gradients. Dendroclimatic information was extracted from a network of 10 silver-fir (Abies alba) populations in the south-western distribution limit of the species (Pyrenees, NE Iberian Peninsula). Ring-width chronologies were built for five stands sampled in mesic sites from the Main Range in the Pyrenees, and for five forests located in the southern Peripheral Ranges where summer drought is more pronounced. The radial growth of silver-fir in this region is constrained by water stress during the summer previous to growth, as suggested by the negative relationship with previous September temperature and, to a lesser degree, by a positive relationship with previous end of summer precipitation. Climatic data showed a warming trend since the 1970s across the Pyrenees, with more severe summer droughts. The recent warming changed the climate-growth relationships, causing higher growth synchrony among sites, and a higher year-to-year growth variation, especially in the southernmost forests. Moving-interval response functions suggested an increasing water-stress effect on radial growth during the last half of the 20th century. The growth period under water stress has extended from summer up to early autumn. Forests located in the southern Peripheral Ranges experienced a more intense water stress, as seen in a shift of their response to precipitation and temperature. The Main-Range sites mainly showed a response to warming. The intensification of water-stress during the late 20th century might affect the future growth performance of the highly-fragmented A. alba populations in the southwestern distribution limit of the species.

  11. Internal stress evolution in Fe laths deformed at low temperature analysed by dislocation dynamics simulations

    International Nuclear Information System (INIS)

    Chaussidon, Julien; Fivel, Marc; Robertson, Christian; Marini, Bernard

    2010-01-01

    Stress evolution in Fe laths undergoing plastic deformation is investigated using three-dimensional dislocation dynamics simulations adapted to body centred cubic crystals, in the ductile to brittle transition temperature range. The selected boundary conditions, applied stress tensor and initial dislocation structures account for the realistic microstructure observed in bainitic steels. The effective stress field projected in the three different {1 0 0}cleavage planes is calculated for two different temperatures (50 and 200 K) and presented quantitatively, in the form of stress/frequency diagrams. It is shown that plastic activity tends to relax the stress acting in certain cleavage planes (the (0 1 0) and (0 0 1) planes) while, at the same time, amplifying the stress acting in other cleavage planes (the (1 0 0) planes). The selective stress amplification in the latter planes depends on the applied load direction, in combination with the limited set of available slip systems and the lath geometry. In the examined configuration, this selection effect is more pronounced with decreasing temperature, emphasizing the role of thermally activated plasticity on deformation-induced stress concentrations

  12. Assessing Faculty Experiences with and Perceptions of an Internal Quality Assurance Process for Undergraduate Distributed Learning Courses: A Pilot Study

    Science.gov (United States)

    Rucker, Ryan; Edwards, Karen; Frass, Lydia R.

    2015-01-01

    To ensure that online courses match traditional classes' quality, some institutions are implementing internal standards for online course design and quality review. The University of South Carolina created the Distributed Learning Quality Review program, based on "Quality Matters'" standards. It was designed to be faculty-guided, as…

  13. Receptor activation and 2 distinct COOH-terminal motifs control G-CSF receptor distribution and internalization kinetics

    NARCIS (Netherlands)

    L.H.J. Aarts (Bart); O. Roovers (Onno); A.C. Ward (Alister); I.P. Touw (Ivo)

    2004-01-01

    textabstractWe have studied the intracellular distribution and internalization kinetics of the granulocyte colony-stimulating factor receptor (G-CSF-R) in living cells using fusion constructs of wild-type or mutant G-CSF-R and enhanced green fluorescent protein (EGFP). Under

  14. Effect of different types of prosthetic platforms on stress-distribution in dental implant-supported prostheses

    Energy Technology Data Exchange (ETDEWEB)

    Minatel, Lurian [Pró-Reitoria de Pesquisa e Pós-graduação (PRPPG), Universidade do Sagrado Coração, USC, 10–50 Irmã Armindal, Jardim Brasil, Bauru, 17011–160, SP (Brazil); Verri, Fellippo Ramos [Department of Dental Materials and Prosthodontics, Araçatuba Dental School, UNESP - Univ Estadual Paulista, 1193 José Bonifácio Street, Vila Mendonça, Araçatuba 16015–050 (Brazil); Kudo, Guilherme Abu Halawa [Pró-Reitoria de Pesquisa e Pós-graduação (PRPPG), Universidade do Sagrado Coração, USC, 10–50 Irmã Armindal, Jardim Brasil, Bauru, 17011–160, SP (Brazil); Faria Almeida, Daniel Augusto de; Souza Batista, Victor Eduardo de; Aparecido Araujo Lemos, Cleidiel; Piza Pellizzer, Eduardo [Department of Dental Materials and Prosthodontics, Araçatuba Dental School, UNESP - Univ Estadual Paulista, 1193 José Bonifácio Street, Vila Mendonça, Araçatuba 16015–050 (Brazil); and others

    2017-02-01

    A biomechanical analysis of different types of implant connections is relevant to clinical practice because it may impact the longevity of the rehabilitation treatment. Therefore, the objective of this study is to evaluate the Morse taper connections and the stress distribution of structures associated with the platform switching (PSW) concept. It will do this by obtaining data on the biomechanical behavior of the main structure in relation to the dental implant using the 3-dimensional finite element methodology. Four models were simulated (with each containing a single prosthesis over the implant) in the molar region, with the following specifications: M1 and M2 is an external hexagonal implant on a regular platform; M3 is an external hexagonal implant using PSW concept; and M4 is a Morse taper implant. The modeling process involved the use of images from InVesalius CT (computed tomography) processing software, which were refined using Rhinoceros 4.0 and SolidWorks 2011 CAD software. The models were then exported into the finite element program (FEMAP 11.0) to configure the meshes. The models were processed using NeiNastram software. The main results are that M1 (regular diameter 4 mm) had the highest stress concentration area and highest microstrain concentration for bone tissue, dental implants, and the retaining screw (P < 0.05). Using the PSW concept increases the area of the stress concentrations in the retaining screw (P < 0.05) more than in the regular platform implant. It was concluded that the increase in diameter is beneficial for stress distribution and that the PSW concept had higher stress concentrations in the retaining screw and the crown compared to the regular platform implant. - Highlights: • The external hexagon implants was unfavorable biomechanical. • The Morse taper implant presented the best biomechanical result. • Platform switching concept increased stress in screw-retained prostheses.

  15. Effect of different types of prosthetic platforms on stress-distribution in dental implant-supported prostheses

    International Nuclear Information System (INIS)

    Minatel, Lurian; Verri, Fellippo Ramos; Kudo, Guilherme Abu Halawa; Faria Almeida, Daniel Augusto de; Souza Batista, Victor Eduardo de; Aparecido Araujo Lemos, Cleidiel; Piza Pellizzer, Eduardo

    2017-01-01

    A biomechanical analysis of different types of implant connections is relevant to clinical practice because it may impact the longevity of the rehabilitation treatment. Therefore, the objective of this study is to evaluate the Morse taper connections and the stress distribution of structures associated with the platform switching (PSW) concept. It will do this by obtaining data on the biomechanical behavior of the main structure in relation to the dental implant using the 3-dimensional finite element methodology. Four models were simulated (with each containing a single prosthesis over the implant) in the molar region, with the following specifications: M1 and M2 is an external hexagonal implant on a regular platform; M3 is an external hexagonal implant using PSW concept; and M4 is a Morse taper implant. The modeling process involved the use of images from InVesalius CT (computed tomography) processing software, which were refined using Rhinoceros 4.0 and SolidWorks 2011 CAD software. The models were then exported into the finite element program (FEMAP 11.0) to configure the meshes. The models were processed using NeiNastram software. The main results are that M1 (regular diameter 4 mm) had the highest stress concentration area and highest microstrain concentration for bone tissue, dental implants, and the retaining screw (P < 0.05). Using the PSW concept increases the area of the stress concentrations in the retaining screw (P < 0.05) more than in the regular platform implant. It was concluded that the increase in diameter is beneficial for stress distribution and that the PSW concept had higher stress concentrations in the retaining screw and the crown compared to the regular platform implant. - Highlights: • The external hexagon implants was unfavorable biomechanical. • The Morse taper implant presented the best biomechanical result. • Platform switching concept increased stress in screw-retained prostheses.

  16. A finite element analysis of the stress distribution to the mandible from impact forces with various orientations of third molars*

    Science.gov (United States)

    Liu, Yun-feng; Wang, Russell; Baur, Dale A.; Jiang, Xian-feng

    2018-01-01

    Objective: To investigate the stress distribution to the mandible, with and without impacted third molars (IM3s) at various orientations, resulting from a 2000-Newton impact force either from the anterior midline or from the body of the mandible. Materials and methods: A 3D mandibular virtual model from a healthy dentate patient was created and the mechanical properties of the mandible were categorized to 9 levels based on the Hounsfield unit measured from computed tomography (CT) images. Von Mises stress distributions to the mandibular angle and condylar areas from static impact forces (Load I-front blow and Load II left blow) were evaluated using finite element analysis (FEA). Six groups with IM3 were included: full horizontal bony, full vertical bony, full 450 mesioangular bony, partial horizontal bony, partial vertical, and partial 450 mesioangular bony impaction, and a baseline group with no third molars. Results: Von Mises stresses in the condyle and angle areas were higher for partially than for fully impacted third molars under both loading conditions, with partial horizontal IM3 showing the highest fracture risk. Stresses were higher on the contralateral than on the ipsilateral side. Under Load II, the angle area had the highest stress for various orientations of IM3s. The condylar region had the highest stress when IM3s were absent. Conclusions: High-impact forces are more likely to cause condylar rather than angular fracture when IM3s are missing. The risk of mandibular fracture is higher for partially than fully impacted third molars, with the angulation of impaction having little effect on facture risk. PMID:29308606

  17. Method to estimate the internal stresses due to moisture in wood using transmission properties of microwaves

    International Nuclear Information System (INIS)

    Takemura, T.; Taniguchi, T.

    2004-01-01

    The purpose of this paper is to offer a new method for detecting stress in wood due to moisture along the lines of a theory reported previously. According to the theory, the stress in wood could be estimated from the moisture content of the wood and the power voltage of a microwave moisture meter (i.e., attenuation of the projected microwave). This seems to suggest a possibility of utilizing microwaves in the field of stress detection. To develop such an idea, the stress formulas were initially modified to the form of an uni-variable function of power voltage, and the application method of the formulas to detection was tried. Finally, these results were applied to the data of sugi (Cryptomeria japonica) lumber in the previous experiment. The estimated strains showed fairly good agreement with those observed. It could be concluded from this study that the proposed method might be available for detecting stress in wood due to moisture

  18. Reproducibility of aluminum foam properties: Effect of precursor distribution on the structural anisotropy and the collapse stress and its dispersion

    International Nuclear Information System (INIS)

    Nosko, M.; Simancik, F.; Florek, R.

    2010-01-01

    The porous structure of aluminum foam manufactured through the foaming of precursors containing blowing agent is stochastic in nature, usually with a random distribution of pores of different size and shape, creating difficulties in the modeling and prediction of foam properties. In this study, the effect of the initial location of the precursor material in the mold on the foam structure and compression behavior was investigated. Structural characterization showed that the porosity distribution, surface skin thickness and pore orientation was affected by the location of the precursors in the mold and by the extrusion direction of the precursors. Moreover, compression tests demonstrated a significant effect of the structural anisotropy on the collapse stress and its dispersion. The collapse stress of the foam increased if the loading was performed parallel to the thicker surface skin or parallel to the preferential pore orientation, leading to a 20% difference in collapse stress. The dispersion of the collapse stress could be significantly decreased if the loading was performed with regard to the structural anisotropy.

  19. Stress Distribution in Single Dental Implant System: Three-Dimensional Finite Element Analysis Based on an In Vitro Experimental Model.

    Science.gov (United States)

    Rezende, Carlos Eduardo Edwards; Chase-Diaz, Melody; Costa, Max Doria; Albarracin, Max Laurent; Paschoeto, Gabriela; Sousa, Edson Antonio Capello; Rubo, José Henrique; Borges, Ana Flávia Sanches

    2015-10-01

    This study aimed to analyze the stress distribution in single implant system and to evaluate the compatibility of an in vitro model with finite element (FE) model. The in vitro model consisted of Brånemark implant; multiunit set abutment of 5 mm height; metal-ceramic screw-retained crown, and polyurethane simulating the bone. Deformations were recorded in the peri-implant region in the mesial and distal aspects, after an axial 300 N load application at the center of the occlusal aspect of the crown, using strain gauges. This in vitro model was scanned with micro CT to design a three-dimensional FE model and the strains in the peri-implant bone region were registered to check the compatibility between both models. The FE model was used to evaluate stress distribution in different parts of the system. The values obtained from the in vitro model (20-587 με) and the finite element analysis (81-588 με) showed agreement among them. The highest stresses because of axial and oblique load, respectively were 5.83 and 40 MPa for the cortical bone, 55 and 1200 MPa for the implant, and 80 and 470 MPa for the abutment screw. The FE method proved to be effective for evaluating the deformation around single implant. Oblique loads lead to higher stress concentrations.

  20. Partial LVAD restores ventricular outputs and normalizes LV but not RV stress distributions in the acutely failing heart in silico

    OpenAIRE

    Sack, Kevin L.; Baillargeon, Brian; Acevedo-Bolton, Gabriel; Genet, Martin; Rebelo, Nuno; Kuhl, Ellen; Klein, Liviu; Weiselthaler, Georg M.; Burkhoff, Daniel; Franz, Thomas; Guccione, Julius M.

    2016-01-01

    Purpose: Heart failure is a worldwide epidemic that is unlikely to change as the population ages and life expectancy increases. We sought to detail significant recent improvements to the Dassault Systèmes Living Heart Model (LHM) and use the LHM to compute left ventricular (LV) and right ventricular (RV) myofiber stress distributions under the following 4 conditions: (1) normal cardiac function; (2) acute left heart failure (ALHF); (3) ALHF treated using an LV assist device (LVAD) flow rate o...

  1. Evaluation on double-wall-tube residual stress distribution of sodium-heated steam generator by neutron diffraction and numerical analysis

    International Nuclear Information System (INIS)

    Kisohara, N.; Suzuki, H.; Akita, K.; Kasahara, N.

    2012-01-01

    A double-wall-tube is nominated for the steam generator heat transfer tube of future sodium fast reactors (SFRs) in Japan, to decrease the possibility of sodium/water reaction. The double-wall-tube consists of an inner tube and an outer tube, and they are mechanically contacted to keep the heat transfer of the interface between the inner and outer tubes by their residual stress. During long term SG operation, the contact stress at the interface gradually falls down due to stress relaxation. This phenomenon might increase the thermal resistance of the interface and degrade the tube heat transfer performance. The contact stress relaxation can be predicted by numerical analysis, and the analysis requires the data of the initial residual stress distributions in the tubes. However, unclear initial residual stress distributions prevent precious relaxation evaluation. In order to resolve this issue, a neutron diffraction method was employed to reveal the tri-axial (radius, hoop and longitudinal) initial residual stress distributions in the double-wall-tube. Strain gauges also were used to evaluate the contact stress. The measurement results were analyzed using a JAEA's structural computer code to determine the initial residual stress distributions. Based on the stress distributions, the structural computer code has predicted the transition of the relaxation and the decrease of the contact stress. The radial and longitudinal temperature distributions in the tubes were input to the structural analysis model. Since the radial thermal expansion difference between the inner (colder) and outer (hotter) tube reduces the contact stress and the tube inside steam pressure contributes to increasing it, the analytical model also took these effects into consideration. It has been conduced that the inner and outer tubes are contacted with sufficient stresses during the plant life time, and that effective heat transfer degradation dose not occur in the double-wall-tube SG. (authors)

  2. The role of prosthetic abutment material on the stress distribution in a maxillary single implant-supported fixed prosthesis

    Energy Technology Data Exchange (ETDEWEB)

    Peixoto, Hugo Eduardo, E-mail: hugo.e.peixoto@hotmail.com [Implantology Team, Latin American Institute of Research and Education in Dentistry, Curitiba, Paraná (Brazil); Bordin, Dimorvan, E-mail: dimorvan_bordin@hotmail.com [Department of Prosthodontics and Periodontology, Piracicaba Dental School, State University of Campinas, Limeira avenue, 901-Vila Rezende, Piracicaba, SP 13414-903 (Brazil); Del Bel Cury, Altair A., E-mail: altcury@fop.unicamp.br [Department of Prosthodontics and Periodontology, Piracicaba Dental School, State University of Campinas, Limeira avenue, 901-Vila Rezende, Piracicaba, SP 13414-903 (Brazil); Silva, Wander José da, E-mail: wanderjose@fop.unicamp.br [Department of Prosthodontics and Periodontology, Piracicaba Dental School, State University of Campinas, Limeira avenue, 901-Vila Rezende, Piracicaba, SP 13414-903 (Brazil); Faot, Fernanda, E-mail: fernanda.faot@gmail.com [Department of Restorative Dentistry, School of Dentistry, Federal University of Pelotas, Gonçalves Chaves, 457, 2nd floor, Pelotas, Rio Grande do Sul 96015-560 (Brazil)

    2016-08-01

    Purpose: Evaluate the influence of abutment's material and geometry on stress distribution in a single implant-supported prosthesis. Materials and Methods: Three-dimensional models were made based on tomographic slices of the upper middle incisor area, in which a morse taper implant was positioned and a titanium (Ti) or zirconia (ZrN) universal abutments was installed. The commercially available geometry of titanium (T) and zirconia (Z) abutments were used to draw two models, TM1 and ZM1 respectively, which served as control groups. These models were compared with 2 experimental groups were the mechanical properties of Z were applied to the titanium abutment (TM2) and vice versa for the zirconia abutment (ZM2). Subsequently, loading was simulated in two steps, starting with a preload phase, calculated with the respective friction coefficients of each materials, followed by a combined preload and chewing force. The maximum von Mises stress was described. Data were analyzed by two-way ANOVA that considered material composition, geometry and loading (p < 0.05). Results: Titanium and zirconia abutments showed similar von Mises stresses in the mechanical part of the four models. The area with the highest concentration of stress was the screw thread, following by the screw body. The highest stress levels occurred in screw thread was observed during the preloading phase in the ZM1 model (931 MPa); and during the combined loading in the TM1 model (965 MPa). Statistically significant differences were observed for loading, the material × loading interaction, and the loading × geometry interaction (p < 0.05). Preloading contributed for 77.89% of the stress (p < 0.05). There were no statistically significant differences to the other factors (p > 0.05). Conclusion: The screw was the piece most intensely affected, mainly through the preload force, independent of the abutment's material. - Highlights: • The abutment's screw was the most impaired piece of the

  3. Application of the photoelastic experimental hybrid method with new numerical method to the high stress distribution

    International Nuclear Information System (INIS)

    Hawong, Jai Sug; Lee, Dong Hun; Lee, Dong Ha; Tche, Konstantin

    2004-01-01

    In this research, the photoelastic experimental hybrid method with Hook-Jeeves numerical method has been developed: This method is more precise and stable than the photoelastic experimental hybrid method with Newton-Rapson numerical method with Gaussian elimination method. Using the photoelastic experimental hybrid method with Hook-Jeeves numerical method, we can separate stress components from isochromatics only and stress intensity factors and stress concentration factors can be determined. The photoelastic experimental hybrid method with Hook-Jeeves had better be used in the full field experiment than the photoelastic experimental hybrid method with Newton-Rapson with Gaussian elimination method

  4. Regulation of distributed generation. A European Policy Paper on the Integration of Distributed Generation in the Internal Electricity Market

    International Nuclear Information System (INIS)

    Van Sambeek, E.J.W.; Scheepers, M.J.J.

    2004-06-01

    In the SUSTELNET project criteria and guidelines have been developed that can create a level playing field in electricity markets between distributed generation (DG) and large scale power generation and will improve the network and market access of DG and electricity supply from renewable energy resources (RES). This report focuses on the European dimensions of DG regulation. The key findings of the SUSTELNET project are compared with the EU legislation, i.e. the current Electricity, Renewables and CHP Directives. Additional EU policy, regulation and initiatives are identified that can help Member States in developing future economically efficient and sustainable electricity supply systems

  5. Modelling effects of tyre inflation pressure on the stress distribution near the soil-tyre interface

    DEFF Research Database (Denmark)

    Schjønning, Per; Lamandé, Mathieu; Tøgersen, Frede A

    2008-01-01

    stress in the contact area for two radial-ply agricultural trailer tyres (650/65R30.5 and 800/50R34) loaded with 60 kN. The study took place on a sandy soil at a water content slightly less than field capacity. We tested the effect of three different inflation pressures (50, 100 and 240 k......Pa) in a randomised block design with three replicates. The vertical stress was measured with load cells located in 0.1 m soil depth. The vertical stress data were used also for identifying the soil area in contact with the tyre, i.e. the tyre footprint. A model (named FRIDA) is proposed that describes the tyre...... footprint by a super ellipse and the stress distribution by a combined exponential (perpendicular to the driving direction) and power-law (along the driving direction) function. The contact area doubled when the inflation pressure was reduced from 240 to 50 kPa. For both tyres, the measured peak stress...

  6. Stress

    DEFF Research Database (Denmark)

    Keller, Hanne Dauer

    2015-01-01

    Kapitlet handler om stress som følelse, og det trækker primært på de få kvalitative undersøgelser, der er lavet af stressforløb.......Kapitlet handler om stress som følelse, og det trækker primært på de få kvalitative undersøgelser, der er lavet af stressforløb....

  7. Stress !!!

    OpenAIRE

    Fledderus, M.

    2012-01-01

    Twee op de vijf UT-studenten hebben last van ernstige studiestress, zo erg zelfs dat het ze in hun privéleven belemmert. Die cijfers komen overeen met het landelijk beeld van stress onder studenten. Samen met 14 andere universiteits- en hogeschoolbladen enquêteerde UT Nieuws bijna 5500 studenten. Opvallend is dat mannelijke studenten uit Twente zich veel minder druk lijken te maken over hun studie. Onder vrouwen ligt de stress juist erg hoog ten opzichte van het landelijk gemiddelde.

  8. Latin America multidisciplinary research on heat shock proteins and cell stress: proceedings of the first conference of the Latin America Chapter of the Cell Stress Society International.

    Science.gov (United States)

    Bausero, María A

    2015-09-01

    The First Conference of the Latin America Chapter of the Cell Stress Society International (CSSI) organized by CSSI was held in Montevideo, Uruguay, on March 11-14, 2014. The Latin America Chapter of the CSSI (LAC-CSSI) was established at the Workshop on the Molecular Biology of the Stress Response, Porto Alegre, Brazil, May 2012. The chapter's first meeting took place in the beautiful city of Montevideo and was chaired by the first (LAC-CSSI) elected president Professor María Bausero. Forty-two invited speakers presented their work to more than 100 scientists. The first day of the conference was dedicated to an introductory program for students, young investigators, and participants new to the field of molecular chaperones and the stress response. These seminars were held in the Pasteur Institute of Montevideo and the Faculty of Sciences of the University of the Republic. These institutions were carefully selected to give foreign participants a broad view of the diversity of students and institutions doing research in Uruguay, as well as an opportunity for direct interaction with our scientists and students. Invited speakers for the seminar series were Dr. Wolfgang Schumann, Dr. Cristina Bonorino, Dr. Antonio De Maio, Dr. Ian Brown, Dr. Rafael Radi, Dr. Daniel Ciocca, and Dr. Celia Quijano. The remaining days of the conference took place at the Sheraton Hotel in Montevideo, and the scientific sessions are discussed below.

  9. Effects of neutron radiation and residual stresses on the corrosion of welds in light water reactor internals

    International Nuclear Information System (INIS)

    Schaaf, Bob van der; Gavillet, Didier; Lapena, Jesus; Ohms, Carsten; Roth, Armin; Dyck, Steven van

    2006-01-01

    After many years of operation in Light Water Reactors (LWR) Irradiation Assisted Stress Corrosion Cracking (IASCC) of internals has been observed. In particular the heat-affected zone (HAZ) has been associated with IASCC attack. The welding process induces residual stresses and micro-structural modifications. Neutron irradiation affects the materials response to mechanical loading. IASCC susceptibility of base materials is widely studied, but the specific conditions of irradiated welds are rarely assessed. Core component relevant welds of Type 304 and 347 steels have been fabricated and were irradiated in the High Flux Reactor (HFR) in Petten to 0.3 and 1 dpa (displacement per atom). In-service welds were cut from the thermal shield of the decommissioned BR-3 reactor. Residual stresses, measured using neutron diffraction, ring core tests and X-ray showed residual stress levels up to 400 MPa. Micro-structural characterization showed higher dislocation densities in the weld and HAZ. Neutron radiation increased the dislocation density, resulting in hardening and reduced fracture toughness. The sensitization degree of the welds, measured with the electrochemical potentio-dynamic reactivation method, was negligible. The Slow Strain Rate Tensile (SSRT) tests, performed at 290 deg. C in water with 200 ppb dissolved oxygen, (DO), did not reveal inter-granular cracking. Inter-granular attack of in-service steel is observed in water with 8 ppm (DO), attributed not only to IASCC, but also to IGSCC from thermal sensitization during fabrication. Stress-relieve annealing has caused Cr-grain boundary precipitation, indicating the sensitization. The simulated internal welds, irradiated up to 1.0 dpa, did not show inter-granular cracking with 8 ppm DO. (authors)

  10. Lithospheric flexure under the Hawaiian volcanic load: Internal stresses and a broken plate revealed by earthquakes

    Science.gov (United States)

    Klein, Fred W.

    2016-01-01

    Several lines of earthquake evidence indicate that the lithospheric plate is broken under the load of the island of Hawai`i, where the geometry of the lithosphere is circular with a central depression. The plate bends concave downward surrounding a stress-free hole, rather than bending concave upward as with past assumptions. Earthquake focal mechanisms show that the center of load stress and the weak hole is between the summits of Mauna Loa and Mauna Kea where the load is greatest. The earthquake gap at 21 km depth coincides with the predicted neutral plane of flexure where horizontal stress changes sign. Focal mechanism P axes below the neutral plane display a striking radial pattern pointing to the stress center. Earthquakes above the neutral plane in the north part of the island have opposite stress patterns; T axes tend to be radial. The M6.2 Honomu and M6.7 Kiholo main shocks (both at 39 km depth) are below the neutral plane and show radial compression, and the M6.0 Kiholo aftershock above the neutral plane has tangential compression. Earthquakes deeper than 20 km define a donut of seismicity around the stress center where flexural bending is a maximum. The hole is interpreted as the soft center where the lithospheric plate is broken. Kilauea's deep conduit is seismically active because it is in the ring of maximum bending. A simplified two-dimensional stress model for a bending slab with a load at one end yields stress orientations that agree with earthquake stress axes and radial P axes below the neutral plane. A previous inversion of deep Hawaiian focal mechanisms found a circular solution around the stress center that agrees with the model. For horizontal faults, the shear stress within the bending slab matches the slip in the deep Kilauea seismic zone and enhances outward slip of active flanks.

  11. FEM Modeling of In-Plane Stress Distribution in Thick Brittle Coatings/Films on Ductile Substrates Subjected to Tensile Stress to Determine Interfacial Strength

    Directory of Open Access Journals (Sweden)

    Kaishi Wang

    2018-03-01

    Full Text Available The ceramic-metal interface is present in various material structures and devices that are vulnerable to failures, like cracking, which are typically due to their incompatible properties, e.g., thermal expansion mismatch. In failure of these multilayer systems, interfacial shear strength is a good measure of the robustness of interfaces, especially for planar films. There is a widely-used shear lag model and method by Agrawal and Raj to analyse and measure the interfacial shear strength of thin brittle film on ductile substrates. The use of this classical model for a type of polymer derived ceramic coatings (thickness ~18 μm on steel substrate leads to high values of interfacial shear strength. Here, we present finite element simulations for such a coating system when it is subjected to in-plane tension. Results show that the in-plane stresses in the coating are non-uniform, i.e., varying across the thickness of the film. Therefore, they do not meet one of the basic assumptions of the classical model: uniform in-plane stress. Furthermore, effects of three significant parameters, film thickness, crack spacing, and Young’s modulus, on the in-plane stress distribution have also been investigated. ‘Thickness-averaged In-plane Stress’ (TIS, a new failure criterion, is proposed for estimating the interfacial shear strength, which leads to a more realistic estimation of the tensile strength and interfacial shear strength of thick brittle films/coatings on ductile substrates.

  12. Velocity and shear stress distribution downstream of mechanical heart valves in pulsatile flow.

    Science.gov (United States)

    Giersiepen, M; Krause, U; Knott, E; Reul, H; Rau, G

    1989-04-01

    Ten mechanical valves (TAD 27 mm): Starr-Edwards Silastic Ball, Björk-Shiley Standard, Björk-Shiley Concave-Convex, Björk-Shiley Monostrut, Hall-Kaster (Medtronic-Hall), OmniCarbon, Bicer Val, Sorin, Saint-Jude Medical and Hemex (Duromedics) are investigated in a comparative in vitro study. The velocity and turbulent shear stress profiles of the valves were determined by Laser Doppler anemometry in two different downstream axes within a model aortic root. Depending on the individual valve design, velocity peaks up to 1.5 m/s and turbulent shear stress peaks up to 150 N/m2 were measured during the systolic phase. These shear stress peaks mainly occurred in areas of flow separation and intense momentum exchange. Directly downstream of the valves (measuring axis 0.55.dAorta) turbulent shear stress peaks occurred at peak systole and during the deceleration phase, while in the second measuring axis (1.5.dAorta) turbulence levels were lower. Shear stress levels were high at the borders of the fluid jets. The results are discussed from a fluid-dynamic point of view.

  13. Acculturative Stress and Disengagement: Learning from the Adjustment Challenges Faced by East Asian International Graduate Students

    Science.gov (United States)

    Lyken-Segosebe, D. E.

    2017-01-01

    International graduate students meet TOEFL, GPA, and other admissions criteria to gain entry into US colleges and universities. During their stay in the USA, they provide educational and economic contributions for their host country. In contrast to their educational and economic potential, international students often demonstrate poor academic and…

  14. β-distribution for Reynolds stress and turbulent heat flux in relaxation turbulent boundary layer of compression ramp

    Science.gov (United States)

    Hu, YanChao; Bi, WeiTao; Li, ShiYao; She, ZhenSu

    2017-12-01

    A challenge in the study of turbulent boundary layers (TBLs) is to understand the non-equilibrium relaxation process after sep-aration and reattachment due to shock-wave/boundary-layer interaction. The classical boundary layer theory cannot deal with the strong adverse pressure gradient, and hence, the computational modeling of this process remains inaccurate. Here, we report the direct numerical simulation results of the relaxation TBL behind a compression ramp, which reveal the presence of intense large-scale eddies, with significantly enhanced Reynolds stress and turbulent heat flux. A crucial finding is that the wall-normal profiles of the excess Reynolds stress and turbulent heat flux obey a β-distribution, which is a product of two power laws with respect to the wall-normal distances from the wall and from the boundary layer edge. In addition, the streamwise decays of the excess Reynolds stress and turbulent heat flux also exhibit power laws with respect to the streamwise distance from the corner of the compression ramp. These results suggest that the relaxation TBL obeys the dilation symmetry, which is a specific form of self-organization in this complex non-equilibrium flow. The β-distribution yields important hints for the development of a turbulence model.

  15. Stress distribution patterns of implant supported overdentures-analog versus finite element analysis: A comparative in-vitro study

    Directory of Open Access Journals (Sweden)

    Soumyadev Satpathy

    2015-01-01

    Full Text Available Aims and Objectives: The aim of this study was to asses & compare the load transfer characteristics of Ball/O-ring and Bar/Clip attachment systems in implant supported overdentures using analog and finite element analysis models. Methodology: For the analog part of the study, castable bar was used for the bar and clip attachment and a metallic housing with a rubber O-ring component was used for the ball/O-ring attachment. The stress on the implant surface was measured using the strain-gauge technique. For the finite element analysis, the model were fabricated and load applications were done in a similar manner as in analog study. Results: The difference between both the attachment systems was found to be statistically significant (P<0.001. Conclusion: Ball/O-ring attachment system transmitted lesser amount of stresses to the implants on the non-loading side, as compared to the Bar-Clip attachment system. When overall stress distribution is compared, the Bar-Clip attachment seems to perform better than the Ball/O-ring attachment, because the force was distributed better.

  16. The global distribution of giant radiating dike swarms on Venus: Implications for the global stress state

    Science.gov (United States)

    Grosfils, Eric B.; Head, James W.

    1994-01-01

    Magellan radar data of Venus reveal 163 large radial lineament systems composed of graben, fissure, and fracture elements. On the basis of their structure, plan view geometry, and volcanic associations, at least 72% are interpreted to have formed primarily through subsurface dike swarm emplacement, the remainder through uplift or a combination of these two mechanisms. The population of swarms is used to determine regional and global stress orientation. The stress configuration recorded from 330-210 deg E (Aphrodite Terra) is best explained by isostatic compensation of existing long wavelength topography or coupling between mantle flow and the lithosphere. The rest are correlated with concentrations of rifting and volcanism in the Beta-Atla-Themis region. The global stress field on Venus is different than that of Earth, where plate boundary forces dominate.

  17. Validation of Weld Residual Stress Modeling in the NRC International Round Robin Study

    International Nuclear Information System (INIS)

    Mullins, Jonathan; Gunnars, Jens

    2013-01-01

    Weld residual stresses (WRS) have a large influence on the behavior of cracks growing under normal operation loads and on the leakage flow from a through-wall crack. Accurate prediction on weld residual stresses is important to make proper decisions when cracks in weld joints are detected. During the latest years, there has been a strong development in both analytical procedures to numerically determine WRS and experimental measurements of WRS. The USNRC (United States Nuclear Regulatory Commission) has formed a program for validation of WRS predictions through comparison of numerically calculated residual stress fields in dissimilar welds measured by different methods. The present report describes the results of the project with special focus on the contribution from Inspecta Technology. Objectives: The principal objective of the project is to compare different WRS predictions for a dissimilar pipe weld with careful measurements on a mock-up weld. The results of the project will make it possible to make recommendations on computational procedures for WRS in dissimilar metal welds. Results: It is concluded that numerical analysis of weld residual stresses using the finite element method is very useful for the estimation of weld residual stresses in complex geometries and dissimilar metal welds. The validation study increases the understanding of uncertainties associated with different modeling approaches and helps to identify the most sensitive parameters

  18. Comparison in stress of caring mothers of children with developmental, external and internal disorders and normal children

    Directory of Open Access Journals (Sweden)

    Narges Zamani

    2017-06-01

    Full Text Available However, having a baby brings positive emotions such as happiness, sense of maturity and proud, parenting's issue could cause high level of stress and child's characteristics was a detrimental factor which can effect on parent's stress, so the aim of this research was comparison of stress of caring in mothers of children with developmental, external, and internal disorders and normal children. The study population included all mothers of children with developmental, emotional, and disruptive behavior disorders, and mothers with normal children in Hamadan (a city in Iran. 240 mothers (4 groups include 60 mothers were chosen based on simple random sampling. Family inventory of life events and changes Mc Cubbin, Patterson & Wilson was used for assessing participants. The results showed that maternal stress in mothers with children who have diagnosis of disruptive behavior disorders were significantly more than of mothers of children with developmental disorders, emotional and mothers of normal children. The present study showed that disruptive behavior disorders in children have a greater impact on their mothers. So, we suggest approved psychological interventions for helping mothers of children with psychological problems, particularly children with external disorders.

  19. Preschoolers' genetic, physiological, and behavioral sensitivity factors moderate links between parenting stress and child internalizing, externalizing, and sleep problems.

    Science.gov (United States)

    Davis, Molly; Thomassin, Kristel; Bilms, Joanie; Suveg, Cynthia; Shaffer, Anne; Beach, Steven R H

    2017-05-01

    This study examined three potential moderators of the relations between maternal parenting stress and preschoolers' adjustment problems: a genetic polymorphism-the short allele of the serotonin transporter (5-HTTLPR, ss/sl allele) gene, a physiological indicator-children's baseline respiratory sinus arrhythmia (RSA), and a behavioral indicator-mothers' reports of children's negative emotionality. A total of 108 mothers (M age  = 30.68 years, SD age  = 6.06) reported on their parenting stress as well as their preschoolers' (M age  = 3.50 years, SD age  = 0.51, 61% boys) negative emotionality and internalizing, externalizing, and sleep problems. Results indicated that the genetic sensitivity variable functioned according to a differential susceptibility model; however, the results involving physiological and behavioral sensitivity factors were most consistent with a diathesis-stress framework. Implications for prevention and intervention efforts to counter the effects of parenting stress are discussed. © 2017 Wiley Periodicals, Inc.

  20. Internal stress relaxation and load redistribution during the twinning-detwinning-dominated cyclic deformation of a wrought magnesium alloy, ZK60A

    International Nuclear Information System (INIS)

    Wu, L.; Agnew, S.R.; Brown, D.W.; Stoica, G.M.; Clausen, B.; Jain, A.; Fielden, D.E.; Liaw, P.K.

    2008-01-01

    A study of the internal strain (stress) evolution during cyclic deformation dominated by {101-bar2} twinning and detwinning mechanisms within a magnesium alloy, ZK60A, was conducted using in situ neutron diffraction. It is shown that once the matrix grains twin, the (00.2) matrix and twin grains are relaxed relative to the neighbors. This load redistribution between the soft- and hard-grain orientations is a result of plastic anisotropy. The twins which formed during the initial compression sustain a tensile stress along the c-axis, when the applied compressive stress is less than ∼80 MPa upon unloading. This local (intergranular) tensile stress is hypothesized to be effective for driving the detwinning event under a macroscopic compressive field along the c-axis. The activation stresses, 15 and 6 MPa, respectively, for the {101-bar2} extension twinning and detwinning, are approximated, based on the relaxation of the internal stresses in the matrix and twin grains