WorldWideScience

Sample records for internal position monitoring

  1. Photon beam position monitor

    Science.gov (United States)

    Kuzay, Tuncer M.; Shu, Deming

    1995-01-01

    A photon beam position monitor for use in the front end of a beamline of a high heat flux and high energy photon source such as a synchrotron radiation storage ring detects and measures the position and, when a pair of such monitors are used in tandem, the slope of a photon beam emanating from an insertion device such as a wiggler or an undulator inserted in the straight sections of the ring. The photon beam position monitor includes a plurality of spaced blades for precisely locating the photon beam, with each blade comprised of chemical vapor deposition (CVD) diamond with an outer metal coating of a photon sensitive metal such as tungsten, molybdenum, etc., which combination emits electrons when a high energy photon beam is incident upon the blade. Two such monitors are contemplated for use in the front end of the beamline, with the two monitors having vertically and horizontally offset detector blades to avoid blade "shadowing". Provision is made for aligning the detector blades with the photon beam and limiting detector blade temperature during operation.

  2. DELTA beam position monitor

    International Nuclear Information System (INIS)

    Brinker, S.; Heisterhagen, R.; Wille, K.

    1991-01-01

    For the electron storage ring DELTA (Dortmund ELectron Test Accelerator) a beam-position-monitor system based on button pickups has been designed. Two different concepts for the monitor electronics have been developed obtaining a long-term stability better than ± 150 μm and a short-term resolution below ± 10 μm. There are no hybrids integrated in the electronic circuits as all four button signals should be amplified and digitized to provide redundancy. First, a concept using four separated electronic branches, one for each button, was tested. Then a concept with a multiplexer in front followed by only one amplifier was designed. This concept, the electronic circuits and the measurements are presented

  3. Beam Position Monitor Engineering

    International Nuclear Information System (INIS)

    Smith, Stephen R.

    1996-07-01

    The design of beam position monitors often involves challenging system design choices. Position transducers must be robust, accurate, and generate adequate position signal without unduly disturbing the beam. Electronics must be reliable and affordable, usually while meeting tough requirements on precision. accuracy, and dynamic range. These requirements may be difficult to achieve simultaneously, leading the designer into interesting opportunities for optimization or compromise. Some useful techniques and tools are shown. Both finite element analysis and analytic techniques will be used to investigate quasi-static aspects of electromagnetic fields such as the impedance of and the coupling of beam to striplines or buttons. Finite-element tools will be used to understand dynamic aspects of the electromagnetic fields of beams, such as wake-fields and transmission-line and cavity effects in vacuum-to-air feed through. Mathematical modeling of electrical signals through a processing chain will be demonstrated, in particular to illuminate areas where neither a pure time-domain nor a pure frequency-domain analysis is obviously advantageous. Emphasis will be on calculational techniques, in particular on using both time-domain and frequency domain approaches to the applicable parts of interesting problems

  4. International monitoring of technology

    International Nuclear Information System (INIS)

    Fischer, W.; Stein, G.

    1990-01-01

    The monitoring of the civilian nuclear energy sector has been effected successfully by IAEA and EURATOM and has contributed to a reduction of fears within the communities of nations. Certainly, it will not be possible to subject the whole world and whole spectrum of technology to monitoring. However, the nations should be enabled to reduce their greatest fears concerning an abuse and a misuse of technology by verification, and to check the compliance with such international agreements which regulate the application of a number of technologies. There are some (as yet rudimentary) approaches to an international verification in the field of environmental protection and resource policies. Nuclear energy with its sophisticated verification procedure has taken one great step ahead of the other fields. The strengths and weaknesses of its verification regime should be learned from when filling the virgin fields of international technology monitoring and its instrument, i.e. international verification. (orig./HSCH) [de

  5. Electrostatic beam-position monitor

    CERN Multimedia

    CERN PhotoLab

    1969-01-01

    Electrostatic beam-position monitor installed in its final location (bake-out cover removed). The ISR will contain about 110 of these monitors. Their accuracy is better than 1 mm, their band width about 1 MHz.

  6. Monitoring and Surveillance in the Workplace: Lessons Learnt? – Investigating the International Legal Position

    Directory of Open Access Journals (Sweden)

    Verine Etsebeth

    2007-06-01

    Full Text Available When considering the legal implications of monitoring and surveillance in the workplace, the question may be asked why companies deploy computer surveillance and monitoring in the first place. Several reasons may be put forward to justify why more than 80% of all major American firms monitor employee e-mails and Internet usage. However, what most companies forget is the fact that the absence or presence of monitoring and surveillance activities in a company holds serious legal consequences for companies. From the discussion in this paper it will become apparent that there is a vast difference in how most countries approach this subject matter. On the one hand America does not afford any employee a reasonable expectation of privacy when it comes to the use of corporate computer resources and systems, while in contrast to this position the United Kingdom goes out of its way to protect each employee’s reasonable expectation of privacy. This paper will not only investigate the different approaches followed by some of the world-leader, but will also investigate the legal consequences embedded in each approach. This paper will ultimately enable the reader to judge for himself/herself which approach his/her country should follow while being fully informed of the legal consequences attached to the chosen approach.

  7. Integration of real-time internal electromagnetic position monitoring coupled with dynamic multileaf collimator tracking: an intensity-modulated radiation therapy feasibility study.

    Science.gov (United States)

    Smith, Ryan L; Sawant, Amit; Santanam, Lakshmi; Venkat, Raghu B; Newell, Laurence J; Cho, Byung-Chul; Poulsen, Per; Catell, Herbert; Keall, Paul J; Parikh, Parag J

    2009-07-01

    Continuous tumor position measurement coupled with a tumor tracking system would result in a highly accurate radiation therapy system. Previous internal position monitoring systems have been limited by fluoroscopic radiation dose and low delivery efficiency. We aimed to incorporate a continuous, electromagnetic, three-dimensional position tracking system (Calypso 4D Localization System) with a dynamic multileaf collimator (DMLC)-based dose delivery system. A research version of the Calypso System provided real-time position of three Beacon transponders. These real-time three-dimensional positions were sent to research MLC controller with a motion-tracking algorithm that changed the planned leaf sequence. Electromagnetic transponders were embedded in a solid water film phantom that moved with patient lung trajectories while being irradiated with two different plans: a step-and-shoot intensity-modulated radiation therapy (S-IMRT) field and a dynamic IMRT (D-IMRT) field. Dosimetric results were recorded under three conditions: no intervention, DMLC tracking, and a spatial gating system. Dosimetric accuracy was comparable for gating and DMLC tracking. Failure rates for gating/DMLC tracking are as follows: +/-3 cGy 10.9/ 7.5% for S-IMRT, 3.3/7.2% for D-IMRT; gamma (3mm/3%) 0.2/1.2% for S-IMRT, 0.2/0.2% for D-IMRT. DMLC tracking proved to be as efficient as standard delivery, with a two- to fivefold efficiency increase over gating. Real-time target position information was successfully integrated into a DMLC effector system to modify dose delivery. Experimental results show both comparable dosimetric accuracy as well as improved efficiency compared with spatial gating.

  8. Tevatron Beam Position Monitor Upgrade

    CERN Document Server

    Wolbers, Stephen; Barker, B; Bledsoe, S; Boes, T; Bowden, Mark; Cancelo, Gugstavo I; Dürling, G; Forster, B; Haynes, B; Hendricks, B; Kasza, T; Kutschke, Robert K; Mahlum, R; Martens, Michael A; Mengel, M; Olsen, M; Pavlicek, V; Pham, T; Piccoli, Luciano; Steimel, Jim; Treptow, K; Votava, Margaret; Webber, Robert C; West, B; Zhang, D

    2005-01-01

    The Tevatron Beam Position Monitor (BPM) readout electronics and software have been upgraded to improve measurement precision, functionality and reliability. The original system, designed and built in the early 1980s, became inadequate for current and future operations of the Tevatron. The upgraded system consists of 960 channels of new electronics to process analog signals from 240 BPMs, new front-end software, new online and controls software, and modified applications to take advantage of the improved measurements and support the new functionality. The new system reads signals from both ends of the existing directional stripline pickups to provide simultaneous proton and antiproton position measurements. Measurements using the new system are presented that demonstrate its improved resolution and overall performance.

  9. Monitoring international nuclear activity

    Energy Technology Data Exchange (ETDEWEB)

    Firestone, R.B.

    2006-05-19

    The LBNL Table of Isotopes website provides primary nuclearinformation to>150,000 different users annually. We have developedthe covert technology to identify users by IP address and country todetermine the kinds of nuclear information they are retrieving. Wepropose to develop pattern recognition software to provide an earlywarning system to identify Unusual nuclear activity by country or regionSpecific nuclear/radioactive material interests We have monitored nuclearinformation for over two years and provide this information to the FBIand LLNL. Intelligence is gleaned from the website log files. Thisproposal would expand our reporting capabilities.

  10. Internationally monitored retrievable storage system

    International Nuclear Information System (INIS)

    Hafele, W.

    1996-01-01

    The proposed internationally monitored retrievable storage system (IMRSS) is intended to provide an orderly and secure alternative to continuation of the current individualistic spent-fuel management trends in nuclear-power countries. The IMRSS concept, in its broadest terms, proposes that an international entity undertake the management responsibility for spent fuel after its discharge from power plant cooling ponds. The IMRSS envisages international management of a small number of surface (or near-surface) storage facilities distributed globally (in major nuclear countries and elsewhere) and a transportation system between nuclear plants and the storage facilities. The International Atomic Energy Agency (IAEA) would maintain responsibility for adherence to safeguards criteria. The IMRSS operation would be similar to that of an international bank, with each nation maintaining title to its spent fuel and able to withdraw it for peaceful purposes. The system would provide transparency, accountability, and security. The IMRSS would be a step to establishing an inter- national regime for the prudent management of spent fuel and excess civilian plutonium. The IMRSS concept has been studied in three international workshops. Among the major issues that have been addressed are the global distribution of spent fuel if current trends continue, the need for international criteria and management to ensure public health and nonproliferation, the value of spent-fuel retrievability, the future role of a plutonium resource in the fuel cycle, the operating format of a practical IMRSS, and the integration of an IMRSS with existing geopolitical agreements and arrangements

  11. Remote monitoring for international safeguards

    International Nuclear Information System (INIS)

    Dupree, S.A.; Sonnier, C.S.

    1999-01-01

    Remote monitoring is not a new technology, and its application to safeguards-relevant activities has been examined for a number of years. On behalf of the U.S. Department of Energy and international partners, remote monitoring systems have been emplaced in nuclear facilities and laboratories in various parts of the world. The experience gained from these Geld trials of remote monitoring systems has shown the viability of the concept of using integrated monitoring systems. Although a wide variety of sensors has been used in the remote monitoring field trials conducted to date, the possible range of instrumentation that might be used has scarcely been touched. As the technology becomes widespread, large amounts of data will become available to inspectors responsible for safeguards activities at the sites. Effective use of remote monitoring will require processing, archiving, presenting, and assessing of these data. To provide reasonable efficiency in the application of this technology, data processing should be done in a careful and organized manner. The problem will be not an issue of poring over scant records but of surviving under a deluge of information made possible by modern technology Fortunately, modem technology, which created the problem of the data glut, is available to come to the assistance of those inundated by data. Apart from the technological problems, one of the most important aspects of remote monitoring is the potential constraint related to the transmission of data out of a facility or beyond national borders. Remote monitoring across national borders can be seriously considered only in the context of a comprehensive, transparent, and open implementation regime. (author)

  12. Organization of internal contamination monitoring

    International Nuclear Information System (INIS)

    Badreddine, A.

    1986-07-01

    The nuclear energy takes a big part in the world's energy production. The nuclear techniques are used in most fields of life. Nevertheless the use of radioactive materials may cause prejudice to human beings by radiation contamination. The International Commission on Radiological Protection gives the general rules and regulations to avoid this danger. In the publication No. 30, the ICRP gives a metabolic model for the respiratory system and values of Annual Limit of Intake. The ALI for inhalation supposes a standard AMAD (Activity Median Aerodynamic Diameter) of 1 um. We have measured the AMAD in a laboratory under different conditions of functioning in order to show its variation. Then we have analysed the effect of this variation on the internal contamination monitoring. Thus we have calculated the Effective Committed Dose (ECD), the ALI, then the Derived Investigation Level (DIL) for different values of AMAD for Whole-Body Counting (WBC)

  13. Internal Electrostatic Discharge Monitor - IESDM

    Science.gov (United States)

    Kim, Wousik; Goebel, Dan M.; Jun, Insoo; Garrett, Henry B.

    2011-01-01

    A document discusses an innovation designed to effectively monitor dielectric charging in spacecraft components to measure the potential for discharge in order to prevent damage from internal electrostatic discharge (IESD). High-energy electrons penetrate the structural materials and shielding of a spacecraft and then stop inside dielectrics and keep accumulating. Those deposited charges generate an electric field. If the electric field becomes higher than the breakdown threshold (approx. =2 x 10(exp 5) V/cm), discharge occurs. This monitor measures potentials as a function of dielectric depth. Differentiation of potential with respect to the depth yields electric field. Direct measurement of the depth profile of the potential in a dielectric makes real-time electronic field evaluation possible without simulations. The IESDM has been designed to emulate a multi-layer circuit board, to insert very thin metallic layers between the dielectric layers. The conductors serve as diagnostic monitoring locations to measure the deposited electron-charge and the charge dynamics. Measurement of the time-dependent potential of the metal layers provides information on the amount of charge deposited in the dielectrics and the movement of that charge with time (dynamics).

  14. The AGS Booster Beam Position Monitor system

    International Nuclear Information System (INIS)

    Ciardullo, D.J.; Abola, A.; Beadle, E.R.; Smith, G.A.; Thomas, R.; Van Zwienen, W.; Warkentien, R.; Witkover, R.L.

    1991-01-01

    To accelerate both protons and heavy ions, the AGS Booster requires a broadband (multi-octave) beam position monitoring system with a dynamic range spanning several orders of magnitude (2 x 10 10 to 1.5 x 10 13 particles per pulse). System requirements include the ability to acquire single turn trajectory and average orbit information with ± 0.1 mm resolution. The design goal of ± 0.5 mm corrected accuracy requires that the detectors have repeatable linear performance after periodic bakeout at 300 degree C. The system design and capabilities of the Booster Beam Position Monitor will be described, and initial results presented. 7 refs., 5 figs

  15. APCAL1: Beam Position Monitor Program

    Energy Technology Data Exchange (ETDEWEB)

    Early, R.A.

    1979-12-01

    APCAL1 is an applications program operational on the PEP MODCOMP IV computer for the purpose of converting beam position monitor (BPM) button voltage readings to x,y coordinates. Calibration information and the BPM readings are read from the MODCOMP IV data base. Corresponding x,y coordinates are written in the data base for use by other programs. APCAL1 is normally activated by another program but can be activated by a touch panel for checkout purposes.

  16. Beam Position Monitor System for PEP II

    Energy Technology Data Exchange (ETDEWEB)

    Smith, Stephen R.; Aiello, G.Roberto; Hendrickson, Linda J.; Johnson, Ronald G.; Mills, Mark R.; Olsen, Jeff J.; /SLAC

    2011-09-12

    We describe the beam position monitor system built for PEP-II, the B-factory at SLAC. The system reports beam position for bunches of between 5 x 10{sup 8} and 8 x 10{sup 10} electron charges, either singly or as continuous streams of bunches every 4.2 ns. Resolution at full charge is to be better than 10 microns in a single turn. Higher resolution is available via on-board multi-turn averaging. The position signal is processed in a 20 MHz bandwidth around 952 MHz. This bandwidth, rather broader than that typical of RF position monitors, allows good resolution for low charge single bunches. Additional novel features include stringent control of return losses in order to minimize cross-talk between nearby bunches which may contain very different charges. The digitizing electronics is multiplexed between the two PEP-II storage rings. Design, construction, and installation experience, as well as first results with beam are presented.

  17. 5th International Symposium on Positive Systems

    CERN Document Server

    Farina, Lorenzo; Setola, Roberto; Germani, Alfredo

    2017-01-01

    This book presents high-quality original contributions on positive systems, including topics such as: monotone dynamical systems in mathematical biology and game theory; mathematical developments for networked systems in biology, chemistry and the social sciences; linear and nonlinear positive operators; dynamical analysis, observation and control of positive distributed parameter systems; stochastic realization theory; biological systems with positive variables and positive controls; iterated function systems; nonnegative dynamic processes; and dimensioning problems for collaborative systems. The book comprises a selection of the best papers presented at the POSTA 2016, the 5th International Symposium on Positive Systems, which was held in Rome, Italy, in September 2016. This conference series represents a targeted response to the growing need for research that reports on and critically discusses a wide range of topics concerning the theory and applications of positive systems.

  18. A machine protection beam position monitor system

    International Nuclear Information System (INIS)

    Medvedko, E.; Smith, S.; Fisher, A.

    1998-01-01

    Loss of the stored beam in an uncontrolled manner can cause damage to the PEP-II B Factory. We describe here a device which detects large beam position excursions or unexpected beam loss and triggers the beam abort system to extract the stored beam safely. The bad-orbit abort trigger beam position monitor (BOAT BPM) generates a trigger when the beam orbit is far off the center (>20 mm), or rapid beam current loss (dI/dT) is detected. The BOAT BPM averages the input signal over one turn (136 kHz). AM demodulation is used to convert input signals at 476 MHz to baseband voltages. The detected signal goes to a filter section for suppression of the revolution frequency, then on to amplifiers, dividers, and comparators for position and current measurements and triggering. The derived current signal goes to a special filter, designed to perform dI/dT monitoring at fast, medium, and slow current loss rates. The BOAT BPM prototype test results confirm the design concepts

  19. Multigigahertz beam-current and position monitor

    International Nuclear Information System (INIS)

    Carlson, R.L.; Stout, L.E.

    1985-01-01

    A self-integrating magnetic-loop device having a risetime of less than 175 ps has been developed to monitor the temporal behavior of the electron beam current and position within each 3.3-ns micropulse generated by the PHERMEX rf linear accelerator. Beam current is measured with a 2-GHz bandwidth by combining these loops in a four-port hybrid summer. Another application of these loops uses two 180 0 hybrids to give 2-GHz time-resolved beam position to an accuracy of 1 mm. These sensors are nonintrusive to the propagating beam and allow ultrafast beam measurements previously restricted to the technique of recording the Cerenkov-light emission from an intercepting Kapton foil using a streak camera

  20. Measuring emittance using beam position monitors

    International Nuclear Information System (INIS)

    Russell, S.; Carlsten, B.

    1993-01-01

    The Los Alamos Advanced Free Electron Laser uses a high charge (greater than InC), low emittance (normalized rams emittance less than 5π mm mrad) photoinjector driven accelerator. The high brightness achieved is due, in large part, to the rapid acceleration of the electrons to relativistic velocities. As a result, the beam does not have time to thermalize its distribution and its universe profile is, in general, non-Gaussian. This, coupled with the very high brightness, makes it difficult to measure the transverse emittance. Techniques used must be able to withstand the rigors of very intense electron beams, and not be reliant on Gaussian assumptions. Beam position monitors are ideal for this. They are not susceptible to beam damage, and it has been shown previously that they can be used to measure the transverse emittance of a beam with a Gaussian profile. However, this Gaussian restriction is not necessary and, in fact, a transverse emittance measurement using beam position monitors is independent of the beam's distribution

  1. Counterstreaming electron beam profile and position monitor

    International Nuclear Information System (INIS)

    Schriber, S.O.; Hohban, K.J.

    1977-01-01

    Individual profiles and positions of two counterstreaming 10 MeV electron beams were measured using the strongly forward directed bremsstrahlung radiation produced when a small fraction of the beam impinges on a tantalum foil. The 0.02 mm wide foil is driven through the electron beams by an external motor connected to the foil by a linear vacuum feedthrough. Bremsstrahlung radiation is detected by a series of ordinary semiconductor diodes spaced around the circumference of the beam vacuum pipe in two planes. The planes are on opposite sides of the foil and are equidistant and parallel to the plane of motion of the foil. The diodes produce output currents proportional to the bremsstrahlung radiation intensity and require no biasing voltages. Design and operational features of the beam monitor for electron beams up to 100 MeV are described. Measurements on counterstreaming 10 MeV pulsed electron beams are presented. Spatial resolutions of 0.3 mm are easily discernable

  2. Advanced Light Source beam position monitor

    International Nuclear Information System (INIS)

    Hinkson, J.

    1991-01-01

    The Advanced Light Source (ALS) is a synchrotron radiation facility nearing completion at LBL. As a third-generation machine, the ALS is designed to produce intense light from bend magnets, wigglers, and undulators (insertion devices). The facility will include a 50 MeV electron linear accelerator, a 1.5 GeV booster synchrotron, beam transport lines, a 1--2 GeV storage ring, insertion devices, and photon beam lines. Currently, the beam injection systems are being commissioned, and the storage ring is being installed. Electron beam position monitors (BPM) are installed throughout the accelerator and constitute the major part of accelerator beam diagnostics. The design of the BPM instruments is complete, and 50 units have been constructed for use in the injector systems. We are currently fabricating 100 additional instruments for the storage ring. In this paper I discuss engineering fabrication, testing and performance of the beam pickup electrodes and the BPM electronics

  3. Signal Processing for Beam Position Monitors

    CERN Document Server

    Vismara, Giuseppe

    2000-01-01

    At the first sight the problem to determine the beam position from the ratio of the induced charges of the opposite electrodes of a beam monitor seems trivial, but up to now no unique solution has been found that fits the various demands of all particle accelerators. The purpose of this paper is to help "instrumentalists" to choose the best processing system for their particular application, depending on the machine size, the input dynamic range, the required resolution and the acquisition speed. After a general introduction and an analysis of the electrical signals to be treated (frequency and time domain), the definition of the electronic specifications will be reviewed. The tutorial will present the different families in which the processing systems can be grouped. A general description of the operating principles with relative advantages and disadvantages for the most employed processing systems is presented. Special emphasis will be put on recent technological developments based on telecommunication circ...

  4. Indirect monitoring of internal exposure for actinides

    International Nuclear Information System (INIS)

    Carneiro G, C.J.; Barreto F, J.; Todo A, A.

    2006-01-01

    The procedure used to the assessment of internal exposure of workers involved with dismantling lightning rods and radioactive smoke detectors is described. Due to the presence of the sources of 241 Am in these devices, a monitoring program to the workers have been implemented. This paper presents an analytical method for the separation and analysis of plutonium (Pu) and americium (Am) in urine samples using solid-phase extraction chromatography and alpha spectrometry. The mean recovery obtained with this technique is about 80% and the detection limit for 24 h urine sample range between 0.6 mBqL -1 and 1.0 mBqL -1 . The assessment of intakes and internal doses are performed following ICRP Publication 78 recommendations and appropriated biokinetic models (ICRP, 1997). Assumptions have been made for routine monitoring of these workers and it is also discussed the establishment of the internal monitoring program using the results of alpha measurements. (Author)

  5. Indirect monitoring of internal exposure for actinides

    Energy Technology Data Exchange (ETDEWEB)

    Carneiro G, C.J.; Barreto F, J.; Todo A, A. [Instituto de Pesquisas Energeticas e Nucleares, IPEN/CNEN, Av. Professor Lineu Prestes No. 2242, Zip code 05508-000, Sao Paulo (Brazil)

    2006-07-01

    The procedure used to the assessment of internal exposure of workers involved with dismantling lightning rods and radioactive smoke detectors is described. Due to the presence of the sources of {sup 241} Am in these devices, a monitoring program to the workers have been implemented. This paper presents an analytical method for the separation and analysis of plutonium (Pu) and americium (Am) in urine samples using solid-phase extraction chromatography and alpha spectrometry. The mean recovery obtained with this technique is about 80% and the detection limit for 24 h urine sample range between 0.6 mBqL{sup -1} and 1.0 mBqL{sup -1}. The assessment of intakes and internal doses are performed following ICRP Publication 78 recommendations and appropriated biokinetic models (ICRP, 1997). Assumptions have been made for routine monitoring of these workers and it is also discussed the establishment of the internal monitoring program using the results of alpha measurements. (Author)

  6. Analytical N beam position monitor method

    Science.gov (United States)

    Wegscheider, A.; Langner, A.; Tomás, R.; Franchi, A.

    2017-11-01

    Measurement and correction of focusing errors is of great importance for performance and machine protection of circular accelerators. Furthermore LHC needs to provide equal luminosities to the experiments ATLAS and CMS. High demands are also set on the speed of the optics commissioning, as the foreseen operation with β*-leveling on luminosity will require many operational optics. A fast measurement of the β -function around a storage ring is usually done by using the measured phase advance between three consecutive beam position monitors (BPMs). A recent extension of this established technique, called the N-BPM method, was successfully applied for optics measurements at CERN, ALBA, and ESRF. We present here an improved algorithm that uses analytical calculations for both random and systematic errors and takes into account the presence of quadrupole, sextupole, and BPM misalignments, in addition to quadrupolar field errors. This new scheme, called the analytical N-BPM method, is much faster, further improves the measurement accuracy, and is applicable to very pushed beam optics where the existing numerical N-BPM method tends to fail.

  7. Beam position monitoring system at CESR

    International Nuclear Information System (INIS)

    Billing, M.G.; Bergan, W.F.; Forster, M.J.; Meller, R.E.; Rendina, M.C.; Rider, N.T.; Sagan, D.C.; Shanks, J.; Sikora, J.P.; Stedinger, M.G.; Strohman, C.R.; Palmer, M.A.; Holtzapple, R.L.

    2017-01-01

    The Cornell Electron-positron Storage Ring (CESR) has been converted from a High Energy Physics electron-positron collider to operate as a dedicated synchrotron light source for the Cornell High Energy Synchrotron Source (CHESS) and to conduct accelerator physics research as a test accelerator, capable of studying topics relevant to future damping rings, colliders and light sources. Some of the specific topics that were targeted for the initial phase of operation of the storage ring in this mode, labeled CESRTA (CESR as a Test Accelerator), included 1) tuning techniques to produce low emittance beams, 2) the study of electron cloud development in a storage ring and 3) intra-beam scattering effects. The complete conversion of CESR to CESRTA occurred over a several year period and is described elsewhere. As a part of this conversion the CESR beam position monitoring (CBPM) system was completely upgraded to provide the needed instrumental capabilities for these studies. This paper describes the new CBPM system hardware, its function and representative measurements performed by the upgraded system.

  8. Numerical simulation of the PEP-II beam position monitor

    Energy Technology Data Exchange (ETDEWEB)

    Kurita, N.; Martin, D.; Ng, C.-K.; Smith, S. [Stanford Linear Accelerator Center, Menlo Park, CA (United States); Weiland, T.

    1996-08-01

    We use MAFIA to analyze the PEP-II button-type beam position monitor (BPM). Employing proper termination of the BPM into a coaxial cable, the output signal at the BPM is determined. Thus the issues of signal sensitivity and power output can be addressed quantitatively, including all transient effects and wakefields. Besides this first quantitative analysis of a true BPM 3D structure, we find that internal resonant modes are a major source of high value narrow-band impedances. The effects of these resonances on coupled-bunch instabilities are discussed. An estimate of the power dissipation in the ceramic vacuum seal under high current operation is given. (author)

  9. Wire Position Monitoring with FPGA based Electronics

    International Nuclear Information System (INIS)

    Eddy, N.; Lysenko, O.

    2009-01-01

    This fall the first Tesla-style cryomodule cooldown test is being performed at Fermilab. Instrumentation department is preparing the electronics to handle the data from a set of wire position monitors (WPMs). For simulation purposes a prototype pipe with a WMP has been developed and built. The system is based on the measurement of signals induced in pickups by 320 MHz signal carried by a wire through the WPM. The wire is stretched along the pipe with a tensioning load of 9.07 kg. The WPM consists of four 50 (Omega) striplines spaced 90 o apart. FPGA based digitizer scans the WPM and transmits the data to a PC via VME interface. The data acquisition is based on the PC running LabView. In order to increase the accuracy and convenience of the measurements some modifications were required. The first is implementation of an average and decimation filter algorithm in the integrator operation in the FPGA. The second is the development of alternative tool for WPM measurements in the PC. The paper describes how these modifications were performed and test results of a new design. The last cryomodule generation has a single chain of seven WPMs (placed in critical positions: at each end, at the three posts and between the posts) to monitor a cold mass displacement during cooldown. The system was developed in Italy in collaboration with DESY. Similar developments have taken place at Fermilab in the frame of cryomodules construction for SCRF research. This fall preliminary cryomodule cooldown test is being performed. In order to prepare an appropriate electronic system for the test a prototype pipe with a WMP has been developed and built, figure 1. The system is based on the measurement of signals induced in pickups by 320 MHz signal carried by a wire through the WPM. The 0.5 mm diameter Cu wire is stretched along the pipe with a tensioning load of 9.07 kg and has a length of 1.1 m. The WPM consists of four 50 (Omega) striplines spaced 90 o apart. An FPGA based digitizer

  10. Monitoring programmes for internal exposure: designing criteria

    International Nuclear Information System (INIS)

    Rojo, Ana M.; Gomez Parada, Ines.

    2007-01-01

    The purpose of this document is to offer guidance for the decision whether a monitoring programme is required and how it should be designed. It can be also used as a tool for making the standing programmes consistent with the most recent publications on internal dosimetry, such as ISO 20553 'Monitoring of workers occupationally exposed to a risk of internal contamination with radioactive material', specific publications of the IAEA and ICRP, and including the conclusions of the OMINEX Project ('Optimisation of Monitoring for Internal Exposures') and IDEAS Project. It is established that the general purpose of the monitoring is verify that each worker is protected adequately against risks from radionuclide intakes and document that the protection complies with legal requirements. The criteria for a particular monitoring programme designing is based on the magnitude of the probable intake and the possibility of detecting a significant event when it occurs. So, the risk assessment for each work process must be evaluated and each worker is classified accordingly. This classification implies the acceptance of reference effective dose values (1 y 6 mSv/y ). (author) [es

  11. A beam position monitor using an amorphous magnetic core

    International Nuclear Information System (INIS)

    Kobayashi, Toshiaki; Ueda, Toru; Yoshida, Yoichi; Kozawa, Takahiro; Uesaka, Mitsuru; Miya, Kenzo; Tagawa, Seiichi; Kobayashi, Hitoshi.

    1994-01-01

    A beam position monitor for an electron accelerator has been developed by using an amorphous magnetic core. The position is detected by the difference of leakage inductances of four pickup coils wound on the amorphous magnetic core. The accuracy of the beam position monitor is less than 1 mm for the various electron pulses from nanosecond to microsecond. (author)

  12. International Radiation Monitoring and Information System (IRMIS)

    Science.gov (United States)

    Mukhopadhyay, Sanjoy; Baciu, Florian; Stowisek, Jan; Saluja, Gurdeep; Kenny, Patrick; Albinet, Franck

    2017-09-01

    This article describes the International Radiation Monitoring Information System (IRMIS) which was developed by the International Atomic Energy Agency (IAEA) with the goal to provide Competent Authorities, the IAEA and other international organizations with a client server based web application to share and visualize large quantities of radiation monitoring data. The data maps the areas of potential impact that can assist countries to take appropriate protective actions in an emergency. Ever since the Chernobyl nuclear power plant accident in April of 19861 European Community (EC) has worked towards collecting routine environmental radiological monitoring data from national networked monitoring systems. European Radiological Data Exchange Platform (EURDEP) was created in 19952 to that end - to provide radiation monitoring data from most European countries reported in nearly real-time. During the response operations for the Fukushima Dai-ichi nuclear power plant accident (March 2011) the IAEA Incident and Emergency Centre (IEC) managed, harmonized and shared the large amount of data that was being generated from different organizations. This task underscored the need for a system which allows sharing large volumes of radiation monitoring data in an emergency. In 2014 EURDEP started the submission of the European radiological data to the International Radiation Monitoring Information System (IRMIS) as a European Regional HUB for IRMIS. IRMIS supports the implementation of the Convention on Early Notification of a Nuclear Accident by providing a web application for the reporting, sharing, visualizing and analysing of large quantities of environmental radiation monitoring data during nuclear or radiological emergencies. IRMIS is not an early warning system that automatically reports when there are significant deviations in radiation levels or when values are detected above certain levels. However, the configuration of the visualization features offered by IRMIS may

  13. Requirements for internal contamination monitoring units

    International Nuclear Information System (INIS)

    Werner, E.; Beyer, D.; Doerfel, H.; Erlenbach, H.; Fischbach, G.; Henrichs, K.; Keller, K.D.; Koenig, K.; Riedel, W.; Scheler, R.; Schieferdecker, H.

    1994-01-01

    For the evaluation of internal contamination by officially authorized monitoring units according to section 63 (6) of the German radiation protection ordinance, a directive will be prepared in order to define uniform requirements for the laboratories in charge of incorporation monitoring by appointment of the relevant authorities. These requirements refer to equipment, to performance of measurements, to interpretation of measured values, to quality control as well as to documentation and to delivery of results. The duties of such laboratories comprise measurements of radioactivity, evaluation of intakes of radionuclides and of the resulting internal radiation dose, but also transmission of results to the employer, to the central dose registry, and under certain circumstances to the authorities. Among the requirements to be met by the laboratory for incorporation control are a sufficient measuring efficiency, the implementation of in-house checks, and the participation in intercomparison programs. For the accomplishment of such duties the laboratory needs appropriate apparatus, rooms, facilities, and staffing. (orig.) [de

  14. 49 CFR 192.477 - Internal corrosion control: Monitoring.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Internal corrosion control: Monitoring. 192.477... Control § 192.477 Internal corrosion control: Monitoring. If corrosive gas is being transported, coupons... internal corrosion. Each coupon or other means of monitoring internal corrosion must be checked two times...

  15. Reflected Light Monitor for Multi-point Position Measurements

    CERN Document Server

    Kakoyan, V H; CERN. Geneva; Margaryan, Yu L; Danielyan, V D

    1999-01-01

    A new semitransparent straightness monitor for high-precision control of the spatial displacements is described. The monitor combines the properties of a thin semitransparent mirror and a segmented photodiode sensor. Laboratory measurements with a prototype monitor show that a position resolution of the order of 5 microns can be achieved.

  16. Internal dosimetry monitoring equipment: Present and future

    International Nuclear Information System (INIS)

    Selby, J.; Carbaugh, E.H.; Lynch, T.P.; Strom, D.J.; Lardy, M.M.

    1993-09-01

    We have attempted to characterize the current and future status of in vivo and in vitro measurement programs coupled with the associated radioanalytical methods and workplace monitoring. Developments in these areas must be carefully integrated by internal dosimetrists, radiochemists and field health physicists. Their goal should be uniform improvement rather than to focus on one specific area (e.g., dose modeling) to the neglect of other areas where the measurement capabilities are substantially less sophisticated and, therefore, the potential source of error is greatest

  17. Survey of environment related monitoring programmes of international organizations and their contribution to international monitoring programmes

    International Nuclear Information System (INIS)

    1986-12-01

    The report is a summary of environment-related monitoring programmes of international governmental organizations and their contribution to international monitoring programmes. it presents the situation as of November 1986: This survey has been prepared by a consultant for the Secretariat as a background document for the second meeting of the Environment Experts, Economic Summit in Munich, November 1986. It serves information purposes only. No claim for completeness is intended. This report may also prove to be helpful for administrators and the scientific community as regards gaining knowledge on present arrangements, approaches and environmental activities in the framework of international organizations. In this light, the present report could facilitate communication and progress in solving pressing environmental problems on the international level. (orig.)

  18. Performance of a reentrant cavity beam position monitor

    Directory of Open Access Journals (Sweden)

    Claire Simon

    2008-08-01

    Full Text Available The beam-based alignment and feedback systems, essential operations for the future colliders, require high resolution beam position monitors (BPMs. In the framework of the European CARE/SRF program, a reentrant cavity BPM with its associated electronics was developed by the CEA/DSM/Irfu in collaboration with DESY. The design, the fabrication, and the beam test of this monitor are detailed within this paper. This BPM is designed to be inserted in a cryomodule, work at cryogenic temperature in a clean environment. It has achieved a resolution better than 10  μm and has the possibility to perform bunch to bunch measurements for the x-ray free electron laser (X-FEL and the International Linear Collider (ILC. Its other features are a small size of the rf cavity, a large aperture (78 mm, and an excellent linearity. A first prototype of a reentrant cavity BPM was installed in the free electron laser in Hamburg (FLASH, at Deutsches Elektronen-Synchrotron (DESY and demonstrated its operation at cryogenic temperature inside a cryomodule. The second, installed, also, in the FLASH linac to be tested with beam, measured a resolution of approximately 4  μm over a dynamic range ±5  mm in single bunch.

  19. Operation of the International Monitoring System Network

    Science.gov (United States)

    Araujo, Fernando; Castillo, Enrique; Nikolova, Svetlana; Daly, Timothy

    2010-05-01

    The IMS is a globally distributed network of monitoring facilities using sensors from four technologies. It is designed to detect the seismic and acoustic waves produced by nuclear test explosions and the subsequently released radioactive isotopes. Monitoring stations transmit their data to the IDC in Vienna, Austria, over a global private network known as the Global Communications Infrastructure (GCI). In order to satisfy the strict data and network availability requirements of the IMS Network, the operation of the facilities and the GCI are managed by IDC Operations. IDC Operations has three functions: the first is to ensure proper operation and functioning of the stations, the second to ensure proper operation and functioning of the GCI, and the third, handled by the IDC Operations Centre is to provide network oversight and incident management. At the core of the IMS Network operations are a series of tools for: monitoring the stations' state of health and data quality, troubleshooting incidents, communicating with internal and external stakeholders, and reporting. An overview of the tools currently used by IDC Operations as well as those under development will be presented. This will include an outline of the IDC's strategy for operations and its dependence on entities both inside and outside the CTBTO.

  20. Prospective evaluation of the need for internal monitoring

    International Nuclear Information System (INIS)

    Barton, T.P.; Bowers, R.R.; Volza, P.

    1992-01-01

    This paper reports that under the revision of 10 CFR 20, workers must be monitored for internal dose only if a prospective evaluation shows that they are likely to exceed 10 percent of an ALI in a year. Past positive whole body counts were reviewed at the Perry Nuclear Power Plant, and the largest uptake was found to be 1.3 percent of an ALI. Past RWPs which had the potential for significant airborne exposure were identified and reviewed. The highest possible uptake was calculated to be 2.5 percent of an ALI, not taking credit for respiratory protection. Committed dose from alpha and pure beta emitters which would not be identified by gamma-sensitive bioassay was found to be negligible. Based on this prospective evaluation, monitoring personnel for internal dose is not required at this facility

  1. Beam position monitor data acquisition for the Advanced Photon Source

    Energy Technology Data Exchange (ETDEWEB)

    Lenkszus, F.R.; Kahana, E.; Votaw, A.J.; Decker, G.A.; Chung, Y.; Ciarlette, D.J.; Laird, R.J.

    1993-06-01

    This paper describes the Beam Position Monitor (BPM) data acquisition scheme for the Advanced Photon Source (APS) storage ring. The storage ring contains 360 beam position monitors distributed around its 1104-meter circumference. The beam position monitor data acquisition system is capable of making turn-by-turn measurements of all BPMs simultaneously. It is VXI-based with each VXI crate containing the electronics for 9 BPMS. The VXI Local Bus is used to provide sustained data transfer rates of up to 13 mega-transfers per second to a scanner module. The system provides single-bunch tracking, bunch-to-bunch measurements, fast digital-averaged positions, beam position history buffering, and synchronized multi-turn measurements. Data is accessible to the control system VME crates via an MXI bus. Dedicated high-speed ports are provided to supply position data to beam orbit feedback systems.

  2. Beam position monitor data acquisition for the Advanced Photon Source

    Energy Technology Data Exchange (ETDEWEB)

    Lenkszus, F.R.; Kahana, E.; Votaw, A.J.; Decker, G.A.; Chung, Y.; Ciarlette, D.J.; Laird, R.J.

    1993-01-01

    This paper describes the Beam Position Monitor (BPM) data acquisition scheme for the Advanced Photon Source (APS) storage ring. The storage ring contains 360 beam position monitors distributed around its 1104-meter circumference. The beam position monitor data acquisition system is capable of making turn-by-turn measurements of all BPMs simultaneously. It is VXI-based with each VXI crate containing the electronics for 9 BPMS. The VXI Local Bus is used to provide sustained data transfer rates of up to 13 mega-transfers per second to a scanner module. The system provides single-bunch tracking, bunch-to-bunch measurements, fast digital-averaged positions, beam position history buffering, and synchronized multi-turn measurements. Data is accessible to the control system VME crates via an MXI bus. Dedicated high-speed ports are provided to supply position data to beam orbit feedback systems.

  3. Global positioning system (GPS) civil monitoring performance specification.

    Science.gov (United States)

    2009-04-30

    This Civil Monitoring Performance Specification (CMPS) is published and maintained at : the direction of the Program Manager for Civil Applications, Global Positioning Systems : Wing (GPSW). The purpose of this document is to provide a comprehensive ...

  4. Microbial Monitoring of the International Space Station

    Science.gov (United States)

    Pierson, Duane L.; Botkin, Douglas J.; Bruce, Rebekah J.; Castro, Victoria A.; Smith, Melanie J.; Oubre, Cherie M.; Ott, C. Mark

    2013-01-01

    Humans living and working in the harsh environment of space present many challenges for habitability engineers and microbiologists. Spacecraft must provide an internal environment in which physical (gas composition, pressure, temperature, and humidity), chemical, and biological environmental parameters are maintained at safe levels. Microorganisms are ubiquitous and will accompany all human-occupied spacecraft, but if biological contamination were to reach unacceptable levels, long-term human space flight would be impossible. Prevention of microbiological problems, therefore, must have a high priority. Historically, prevention of infectious disease in the crew has been the highest priority, but experience gained from the NASA-Mir program showed that microbial contamination of vehicle and life-support systems, such as biofouling of water and food, are of equal importance. The major sources of microbiological risk factors for astronauts include food, drinking water, air, surfaces, payloads, research animals, crew members, and personnel in close contact with the astronauts. In our efforts to eliminate or mitigate the negative effects of microorganisms in spacecraft, the National Aeronautics and Space Administration (NASA) implemented comprehensive microbial analyses of the major risk factors. This included the establishment of acceptability requirements for food, water, air, surfaces, and crew members. A robust monitoring program was then implemented to verify that the risks were within acceptable limits. Prevention of microbiological problems is preferred over mitigation of problems during flight, and preventive steps must begin very early in the design phase. Spacecraft development must include requirements to control free water from humidity, condensate, hygiene activities, and other releases. If water is available, microbes are likely to grow because sufficient nutrients are potentially available. Materials selected for the spacecraft must not promote or support

  5. Beam position monitor using a reentrant coaxial cavity

    International Nuclear Information System (INIS)

    Bossart, R.

    1991-01-01

    A special beam position monitor is used in the enlarged straight sections of the SPS accelerator at CERN, in order to measure the position of the proton beam bunched at 200 MHz. A reentrant coaxial cavity connected to the circular vacuum chamber acts as shunt impedance for measuring the wall currents induced by the beam on the vacuum chamber. The coaxial cavity works at 200 MHz much below it's resonance frequency. Both the horizontal and vertical beam position can be measured by four orthogonal signal ports. A good response of the beam position monitor has been obtained as for signal power, precision of centre position, linearity of the position measurement and decoupling between horizontal and vertical position measurement. The total position error ε amounts to ε≤±0.6 mm±0.01 x, where x is the distance of the beam centre from the monitor centre, measured along the x-axis, for horizontal and vertical beam positions up to 60 mm. This paper describes the analysis of the reentrant coaxial cavity and it's application as a position monitor at very high frequencies. (author)

  6. Monitoring requirements for assessment of internal dose

    International Nuclear Information System (INIS)

    Eckerman, K.F.

    1985-01-01

    Data obtained by routine personnel monitoring is usually not a sufficient basis for estimation of dose. Collected data must be interpreted carefully and supplemented with appropriate information before reasonably accurate estimates of dose (i.e., accurate enough to indicate whether or nor personnel are exposed in excess of recommended limits) can be developed. When the exposure is of sufficient magnitude that a rather precise estimate of dose is needed, the health physicist will bring to bear on the problem other, more refined, methods of dosimetry. These might include a reconstruction of the incident and, for internal emitters, an extensive series of in vivo measurements or analyses of excreta. Thus, cases of special significance must often be evaluated using techniques and resources beyond those routinely employed. This is not a criticism of most routine monitoring programs. These programs are usually carefully designed in a manner commensurate with the degree of exposure routinely encountered and the requirement of a practical program of radiation protection. 10 refs

  7. National and international nuclear material monitoring

    International Nuclear Information System (INIS)

    Waddoups, I.G.

    1996-01-01

    The status of nuclear materials in both the U.S. and Former Soviet Union is changing based upon the execution of agreements relative to weapons materials production and weapon dismantlement. The result of these activities is that a considerably different emphasis is being placed on how nuclear materials are viewed and utilized. Even though much effort is being expended on the final disposition of these materials, the interim need for storage and security of the material is increasing. Both safety and security requirements exist to govern activities when these materials are placed in storage. These requirements are intended to provide confidence that the material is not being misused and that the storage operations are conducted safely. Both of these goals can be significantly enhanced if technological monitoring of the material is performed. This paper will briefly discuss the traditional manual methods of U.S. and international material monitoring and then present approaches and technology that are available to achieve the same goals under the evolving environment

  8. Monitoring the beam position in the SLC interaction region

    International Nuclear Information System (INIS)

    Denard, J.C.; Bowden, G.B.; Oxoby, G.J.; Pellegrin, J.L.; Ross, M.C.

    1987-03-01

    The Stanford Linear Collider requires special Beam Position Monitors near the Interaction Point (IP) to bring the two beams (e + and e - ) into collision. These beams pass through two monitors on each side of the IP with a short time separation (about 20 and 50 ns). The mechanics of the monitors as well as the electronics will be described. In order to bring beams of several microns diameter into collision at the IP, these monitors measure beam deflection induced by the presence of the opposite beam

  9. Monitoring the beam position in the SLC interaction region

    International Nuclear Information System (INIS)

    Denard, J.C.; Bowden, G.B.; Oxoby, G.J.; Pellegrin, J.L.; Ross, M.C.

    1987-01-01

    The Stanford Linear Collider requires special Beam Position Monitors near the Interaction Point (IP) to bring the two beams (e/sup +/ and /sup e-/) into collision. These beams pass through two monitors on each side of the IP with a short time separation (about 20 and 50ns). The mechanics of the monitors as well as the electronics will be described. In order to bring beams of several microns diameter into collision at the IP, these monitors measure beam deflection induced by the presence of the opposite beam

  10. MONITORED GEOLOGIC REPOSITORY INTERNAL HAZARDS ANALYSIS

    International Nuclear Information System (INIS)

    S.E. Salzman

    1999-01-01

    This analysis was performed by the Management and Operating Contractor (M andO) Safety Assurance Department to identify and document the internal hazards and preliminary events associated with preclosure operations of the Monitored Geologic Repository (MGR). Internal hazards are those hazards presented by operation of the facility and associated processes. These are in contrast to external hazards which involve natural phenomena and external man-made hazards. The hazard analysis methodology used in this analysis provides a systematic means to identify facility hazards and associated events that may result in radiological consequences to the public and facility worker during the MGR preclosure period. The events are documented in a preliminary events list and are intended to be used as input to the MGR Design Basis Event (DBE) selection process. It is expected that the results from this analysis will undergo further screening and analysis based on the criteria that apply to the performance of DBE analyses for the preclosure period of repository operation. As the MGR design progresses, this analysis will be reviewed to ensure no new hazards are introduced and that previously evaluated hazards have not increased in severity

  11. Operation of International Monitoring System Network

    Science.gov (United States)

    Nikolova, Svetlana; Araujo, Fernando; Aktas, Kadircan; Malakhova, Marina; Otsuka, Riyo; Han, Dongmei; Assef, Thierry; Nava, Elisabetta; Mickevicius, Sigitas; Agrebi, Abdelouaheb

    2015-04-01

    The IMS is a globally distributed network of monitoring facilities using sensors from four technologies: seismic, hydroacoustic, infrasound and radionuclide. It is designed to detect the seismic and acoustic waves produced by nuclear test explosions and the subsequently released radioactive isotopes. Monitoring stations transmit their data to the IDC in Vienna, Austria, over a global private network known as the GCI. Since 2013, the data availability (DA) requirements for IMS stations account for quality of the data, meaning that in calculation of data availability data should be exclude if: - there is no input from sensor (SHI technology); - the signal consists of constant values (SHI technology); Even more strict are requirements for the DA of the radionuclide (particulate and noble gas) stations - received data have to be analyzed, reviewed and categorized by IDC analysts. In order to satisfy the strict data and network availability requirements of the IMS Network, the operation of the facilities and the GCI are managed by IDC Operations. Operations has following main functions: - to ensure proper operation and functioning of the stations; - to ensure proper operation and functioning of the GCI; - to ensure efficient management of the stations in IDC; - to provide network oversight and incident management. At the core of the IMS Network operations are a series of tools for: monitoring the stations' state of health and data quality, troubleshooting incidents, communicating with internal and external stakeholders, and reporting. The new requirements for data availability increased the importance of the raw data quality monitoring. This task is addressed by development of additional tools for easy and fast identifying problems in data acquisition, regular activities to check compliance of the station parameters with acquired data by scheduled calibration of the seismic network, review of the samples by certified radionuclide laboratories. The DA for the networks of

  12. Positive Aspects of International Student Transitions: A Qualitative Inquiry

    Science.gov (United States)

    Moores, Lisa; Popadiuk, Natalee

    2011-01-01

    Despite the considerable growth of the international student population, positive aspects of their experience have received little attention. The current study combines a Critical Incident Technique methodology and a positive psychology lens to explore the cross-cultural transition of seven international students, focusing on facilitative factors,…

  13. Emergency preparedness and internal contamination monitoring

    International Nuclear Information System (INIS)

    Rahola, T.; Suomela, M.

    2000-01-01

    After the radiation accidents in Chernobyl, Ukraina in 1986 and in Goiania, Brasil in 1987, much resource have been spent on improving emergency preparedness. Especially regarding transfer of information using the most recent techniques and establishment of 24 hour emergency service of radiation safety experts the development has been fast. The very first measures in a possible emergency situation have been trained nationally and internationally. Less attention has been paid to measures in a somewhat later phase. To be able to react fast enough in an emergency situation it is essential to have well documented plans, written instructions and suitable measurement equipment ready for use. Equally important is that there is trained staff prepared to do measurements without delay. In the first phase of a nuclear accident radioactive iodine is of primary concern regarding internal contamination. After the Chernobyl accident the number of childhood thyroidea cancer clearly exceeded the expected number. Reliable direct measurements of I-131 in the thyroidea in Ukraina, Russia and Belarussia were done only to a limited number of children. Many uncertainties are involved in the data used for dose estimation. Later the body burdens of radiocesium or other radionuclides might be of most importance. Normal whole-body counting instruments can be used if only small groups need to be measured. For large groups of people in an emergency situation faster methods are needed. Different types of monitors installed at places where radiation workers are controlled for internal contamination as well as gamma cameras at hospitals can be used. Rapid field measurements of the whole-body and especially of the thyroid can been done with less sophisticated instruments. In the acute phase of a nuclear accident such measurements should be done without delay. Instruments and staff trained to use them should be available and plans for which groups of people to measure prepared. The detection level

  14. Monitoring and Reporting Tools of the International Data Centre and International Monitoring System

    Science.gov (United States)

    Lastowka, L.; Anichenko, A.; Galindo, M.; Villagran Herrera, M.; Mori, S.; Malakhova, M.; Daly, T.; Otsuka, R.; Stangel, H.

    2007-05-01

    The Comprehensive Test-Ban Treaty (CTBT) which prohibits all nuclear explosions was opened for signature in 1996. Since then, the Preparatory Commission for the CTBT Organization has been working towards the establishment of a global verification regime to monitor compliance with the ban on nuclear testing. The International Monitoring System (IMS) comprises facilities for seismic, hydroacoustic, infrasound and radionuclide monitoring, and the means of communication. This system is supported by the International Data Centre (IDC), which provides objective products and services necessary for effective global monitoring. Upon completion of the IMS, 321 stations will be contributing to both near real-time and reviewed data products. Currently there are 194 facilities in IDC operations. This number is expected to increase by about 40% over the next few years, necessitating methods and tools to effectively handle the expansion. The requirements of high data availability as well as operational transparency are fundamental principals of IMS network operations, therefore, a suite of tools for monitoring and reporting have been developed. These include applications for monitoring Global Communication Infrastructure (GCI) links, detecting outages in continuous and segmented data, monitoring the status of data processing and forwarding to member states, and for systematic electronic communication and problem ticketing. The operation of the IMS network requires the help of local specialists whose cooperation is in some cases ensured by contracts or other agreements. The PTS (Provisional Technical Secretariat) strives to make the monitoring of the IMS as standardized and efficient as possible, and has therefore created the Operations Centre in which the use of most the tools are centralized. Recently the tasks of operations across all technologies, including the GCI, have been centralized within a single section of the organization. To harmonize the operations, an ongoing State

  15. rf beam-current, -phase, and -position monitors

    International Nuclear Information System (INIS)

    Young, L.

    1984-01-01

    A prototype rf beam monitor has been tested on the Racetrack Microtron's (RTM) 100 kV injector beam line at the National Bureau of Standards (NBS). This beam monitor is capable of measuring the current, the relative phase, and the position of the beam. The beam is bunched at 2380 MHz for acceleration by the linac in the injector beam line. This train of beam bunches passing through the beam monitor cavities excites the cavities at this resonance frequency of 2380 MHz. Probes in the cavities couple some of the beam-excited rf power out of the cavities. This rf power can be amplified if necessary and then analyzed by a double balanced mixer (DBM). The DBM can also be used as a phase detector. The effective shunt impedance of the cavities was measured with the CW beam. For the position monitor cavity, the shunt impedance is proportional to the displacement from the axis. The measured response of the prototype rf beam current monitor setup is a linear function of beam current. Response of the rf beam-position monitor is also shown

  16. Design of the AGS Booster Beam Position Monitor electronics

    International Nuclear Information System (INIS)

    Ciardullo, D.J.; Smith, G.A.; Beadle, E.R.

    1991-01-01

    The operational requirements of the AGS Booster Beam Position Monitor system necessitate the use of electronics with wide dynamic range and broad instantaneous bandwidth. Bunch synchronization is provided by a remote timing sequencer coupled to the local ring electronics via digital fiber-optic links. The Sequencer and local ring circuitry work together to provide single turn trajectory or average orbit and intensity information, integrated over 1 to 225 bunches. Test capabilities are built in for the purpose of enhancing BPM system accuracy. This paper describes the design of the Booster Beam Position Monitor electronics, and presents performance details of the front end processing, acquisition and timing circuitry

  17. Simulations of LEIR Injection Line Beam Position Monitors

    CERN Document Server

    Maltseva, Mariya

    2016-01-01

    In this paper sensitivity characteristics of a beam position monitor are described. Characteristics are obtained during the simulations in CST Studio, the results are compared with the calculated values. The results for a low-beta beam and with a wire are compared.

  18. Linac BPM [Beam Position Monitor] modification program status

    International Nuclear Information System (INIS)

    Smith, S.; Williams, S.

    1990-01-01

    In the fall of 1988 the Beam Position Monitor (BPM) Task Force recommended that linac BPM processors be pulled out of the linac, modified, adjusted for offsets, recalibrated, and reinstalled. As of the end of 1989 this process had been completed on all linac type BPM processors. This paper discusses these modifications and tests

  19. High current precision long pulse electron beam position monitor

    CERN Document Server

    Nelson, S D; Fessenden, T J; Holmes, C

    2000-01-01

    Precision high current long pulse electron beam position monitoring has typically experienced problems with high Q sensors, sensors damped to the point of lack of precision, or sensors that interact substantially with any beam halo thus obscuring the desired signal. As part of the effort to develop a multi-axis electron beam transport system using transverse electromagnetic stripline kicker technology, it is necessary to precisely determine the position and extent of long high energy beams for accurate beam position control (6 - 40 MeV, 1 - 4 kA, 2 μs beam pulse, sub millimeter beam position accuracy.) The kicker positioning system utilizes shot-to-shot adjustments for reduction of relatively slow (< 20 MHz) motion of the beam centroid. The electron beams passing through the diagnostic systems have the potential for large halo effects that tend to corrupt position measurements.

  20. Internal control in the company in order to financial monitoring

    Directory of Open Access Journals (Sweden)

    Osipov A.V.

    2017-04-01

    Full Text Available the article explores the definition of financial monitoring, financial analysis and internal control in aspect to their correlation to fight money laundering and terrorism financing. Internal control is analyzed from the point of view of law, economics and management. The author pays much attention in the article to the work of systems of financial monitoring in organizations.

  1. Beam position monitor for energy recovered linac beams

    Energy Technology Data Exchange (ETDEWEB)

    Powers, Thomas; Evtushenko, Pavel

    2017-06-06

    A method of determining the beam position in an energy recovered linac (ERL). The method makes use of in phase and quadrature (I/Q) demodulation techniques to separate the pickup signal generated by the electromagnetic fields generated by the first and second pass beam in the energy recovered linac. The method includes using analog or digital based I/Q demodulation techniques in order to measure the relative amplitude of the signals from a position sensitive beam pickup such as a button, strip line or microstripline beam position monitor.

  2. Beam Position and Phase Monitor - Wire Mapping System

    Energy Technology Data Exchange (ETDEWEB)

    Watkins, Heath A [Los Alamos National Laboratory; Shurter, Robert B. [Los Alamos National Laboratory; Gilpatrick, John D. [Los Alamos National Laboratory; Kutac, Vincent G. [Los Alamos National Laboratory; Martinez, Derwin [Los Alamos National Laboratory

    2012-04-10

    The Los Alamos Neutron Science Center (LANSCE) deploys many cylindrical beam position and phase monitors (BPPM) throughout the linac to measure the beam central position, phase and bunched-beam current. Each monitor is calibrated and qualified prior to installation to insure it meets LANSCE requirements. The BPPM wire mapping system is used to map the BPPM electrode offset, sensitivity and higher order coefficients. This system uses a three-axis motion table to position the wire antenna structure within the cavity, simulating the beam excitation of a BPPM at a fundamental frequency of 201.25 MHz. RF signal strength is measured and recorded for the four electrodes as the antenna position is updated. An effort is underway to extend the systems service to the LANSCE facility by replacing obsolete electronic hardware and taking advantage of software enhancements. This paper describes the upgraded wire positioning system's new hardware and software capabilities including its revised antenna structure, motion control interface, RF measurement equipment and Labview software upgrades. The main purpose of the wire mapping system at LANSCE is to characterize the amplitude response versus beam central position of BPPMs before they are installed in the beam line. The wire mapping system is able to simulate a beam using a thin wire and measure the signal response as the wire position is varied within the BPPM aperture.

  3. Program Officer, Monitoring and Evaluation | IDRC - International ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    The PO champions the utility and data quality of the Centre's monitoring systems to support learning and reporting. S/he is a “super user” who provides support and advice to staff across the Centre on uses and improvements to our data systems. S/he will provide support to the diverse approaches to monitoring and help ...

  4. Performance of a high resolution cavity beam position monitor system

    International Nuclear Information System (INIS)

    Walston, Sean; Boogert, Stewart; Chung, Carl; Fitsos, Pete; Frisch, Joe; Gronberg, Jeff; Hayano, Hitoshi; Honda, Yosuke; Kolomensky, Yury; Lyapin, Alexey; Malton, Stephen; May, Justin; McCormick, Douglas; Meller, Robert; Miller, David; Orimoto, Toyoko; Ross, Marc; Slater, Mark; Smith, Steve; Smith, Tonee; Terunuma, Nobuhiro; Thomson, Mark; Urakawa, Junji; Vogel, Vladimir; Ward, David; White, Glen

    2007-01-01

    It has been estimated that an RF cavity Beam Position Monitor (BPM) could provide a position measurement resolution of less than 1nm. We have developed a high resolution cavity BPM and associated electronics. A triplet comprised of these BPMs was installed in the extraction line of the Accelerator Test Facility (ATF) at the High Energy Accelerator Research Organization (KEK) for testing with its ultra-low emittance beam. The three BPMs were each rigidly mounted inside an alignment frame on six variable-length struts which could be used to move the BPMs in position and angle. We have developed novel methods for extracting the position and tilt information from the BPM signals including a robust calibration algorithm which is immune to beam jitter. To date, we have demonstrated a position resolution of 15.6nm and a tilt resolution of 2.1μrad over a dynamic range of approximately +/-20μm

  5. Performance of a High Resolution Cavity Beam Position Monitor System

    Energy Technology Data Exchange (ETDEWEB)

    Walston, S; Boogert, S; Chung, C; Fitsos, P; Frisch, J; Gronberg, J; Hayano, H; Honda, Y; Kolomensky, Y; Lyapin, A; Malton, S; May, J; McCormick, D; Meller, R; Miller, D; Orimoto, T; Ross, M; Slater, M; Smith, S; Smith, T; Terunuma, N; Thomson, M; Urakawa, J; Vogel, V; Ward, D; White, G

    2006-12-18

    It has been estimated that an RF cavity Beam Position Monitor (BPM) could provide a position measurement resolution of less than one nanometer. We have developed a high resolution cavity BPM and associated electronics. A triplet comprised of these BPMs was installed in the extraction line of the Accelerator Test Facility (ATF) at the High Energy Accelerator Research Organization (KEK) for testing with its ultra-low emittance beam. The three BPMs were each rigidly mounted inside an alignment frame on six variable-length struts which could be used to move the BPMs in position and angle. We have developed novel methods for extracting the position and tilt information from the BPM signals including a robust calibration algorithm which is immune to beam jitter. To date, we have demonstrated a position resolution of 15.6 nm and a tilt resolution of 2.1 {micro}rad over a dynamic range of approximately {+-} 20 {micro}m.

  6. Performance of a High Resolution Cavity Beam Position Monitor System

    Energy Technology Data Exchange (ETDEWEB)

    Walston, Sean; Boogert, Stewart; Chung, Carl; Fitsos, Joe; Frisch, Joe; Gronberg, Jeff; Hayano, Hitoshi; Honda, Yosuke; Kolomensky, Yury; Lyapin, Alexey; Malton, Stephen; May, Justin; McCormick, Douglas; Meller, Robert; Miller, David John; Orimoto, Toyoko; Ross, Marc; Slater, Mark; Smith, Steve; Smith, Tonee; Terunuma, Nobuhiro; /Fermilab /UC,

    2007-06-08

    It has been estimated that an RF cavity Beam Position Monitor (BPM) could provide a position measurement resolution of less than one nanometer. We have developed a high resolution cavity BPM and associated electronics. A triplet comprised of these BPMs was installed in the extraction line of the Accelerator Test Facility (ATF) at the High Energy Accelerator Research Organization (KEK) for testing with its ultra-low emittance beam. The three BPMs were each rigidly mounted inside an alignment frame on six variable-length struts which could be used to move the BPMs in position and angle. We have developed novel methods for extracting the position and tilt information from the BPM signals including a robust calibration algorithm which is immune to beam jitter. To date, we have demonstrated a position resolution of 15.6 nm and a tilt resolution of 2.1 {mu}rad over a dynamic range of approximately {+-} 20 {mu}m.

  7. Comparison of beam-position-transfer functions using circular beam-position monitors

    International Nuclear Information System (INIS)

    Gilpatrick, J.D.

    1997-01-01

    A cylindrical beam-position monitor (BPM) used in many accelerator facilities has four electrodes on which beam-image currents induce bunched-beam signals. These probe-electrode signals are geometrically configured to provide beam-position information about two orthogonal axes. An electronic processor performs a mathematical transfer function (TF) on these BPM-electrode signals to produce output signals whose time-varying amplitude is proportional to the beam's vertical and horizontal position. This paper will compare various beam-position TFs using both pencil beams and will further discuss how diffuse beams interact with some of these TFs

  8. A phase-space beam position monitor for synchrotron radiation

    International Nuclear Information System (INIS)

    Samadi, Nazanin; Bassey, Bassey; Martinson, Mercedes; Belev, George; Dallin, Les; Jong, Mark de; Chapman, Dean

    2015-01-01

    A system has been developed to measure the vertical position and angle of the electron beam at a single location from a synchrotron source. The system uses a monochromator tuned to the absorption edge of a contrast material and has a sensitivity comparable with other beam position monitors. The stability of the photon beam position on synchrotron beamlines is critical for most if not all synchrotron radiation experiments. The position of the beam at the experiment or optical element location is set by the position and angle of the electron beam source as it traverses the magnetic field of the bend-magnet or insertion device. Thus an ideal photon beam monitor would be able to simultaneously measure the photon beam’s position and angle, and thus infer the electron beam’s position in phase space. X-ray diffraction is commonly used to prepare monochromatic beams on X-ray beamlines usually in the form of a double-crystal monochromator. Diffraction couples the photon wavelength or energy to the incident angle on the lattice planes within the crystal. The beam from such a monochromator will contain a spread of energies due to the vertical divergence of the photon beam from the source. This range of energies can easily cover the absorption edge of a filter element such as iodine at 33.17 keV. A vertical profile measurement of the photon beam footprint with and without the filter can be used to determine the vertical centroid position and angle of the photon beam. In the measurements described here an imaging detector is used to measure these vertical profiles with an iodine filter that horizontally covers part of the monochromatic beam. The goal was to investigate the use of a combined monochromator, filter and detector as a phase-space beam position monitor. The system was tested for sensitivity to position and angle under a number of synchrotron operating conditions, such as normal operations and special operating modes where the photon beam is intentionally altered

  9. Simulgeo and its application for the muon barrel position monitor

    International Nuclear Information System (INIS)

    Brunel, L.

    1999-01-01

    The design process of the Muon Barrel Position Monitor of the CMS (compact muon solenoid) experiment for LHC is at the origin of the need of a software like Simulgeo. The software Silmugeo started to be developed in 1995 in order to allow the study of many systems. The idea of Simulgeo is to automatically make the modelling of a system and automatically construct the design matrix. This paper makes in part 2 an overview of the possibilities of Simulgeo, in part 3 it presents the standard objects. In part 4, it explains the mathematical basis and in part 5 the computing aspect. In part 6, it shows an application to the Muon Barrel Position Monitor Project and, in part 7, it mentions other projects where it has been used

  10. FERMILAB SWITCHYARD RESONANT BEAM POSITION MONITOR ELECTRONICS UPGRADE RESULTS

    Energy Technology Data Exchange (ETDEWEB)

    Petersen, T. [Fermilab; Diamond, J. [Fermilab; Liu, N. [Fermilab; Prieto, P. S. [Fermilab; Slimmer, D. [Fermilab; Watts, A. [Fermilab

    2016-10-12

    The readout electronics for the resonant beam position monitors (BPMs) in the Fermilab Switchyard (SY) have been upgraded, utilizing a low noise amplifier transition board and Fermilab designed digitizer boards. The stripline BPMs are estimated to have an average signal output of between -110 dBm and -80 dBm, with an estimated peak output of -70 dBm. The external resonant circuit is tuned to the SY machine frequency of 53.10348 MHz. Both the digitizer and transition boards have variable gain in order to accommodate the large dynamic range and irregularity of the resonant extraction spill. These BPMs will aid in auto-tuning of the SY beamline as well as enabling operators to monitor beam position through the spill.

  11. Characterization of beam position monitors in two-dimensions

    International Nuclear Information System (INIS)

    Power, J.; Gilpatrick, D.; Neri, F.; Shurter, B.

    1992-01-01

    We describe characterization of a beam position measuring system. We used an automatic test fixture to map the response in two dimensions of dual-axis beam position monitors (BPMs) and their associated ratio-signal processing electronics and applied signals to a thin wire whose position is controlled by stepper motor actuators on x-y stages. The wire may be moved within a circular area of up to 50 mm in diameter with 5-μm accuracy. The resulting signals picked up by a BPM are recorded for each point on a grid within the mapping area. We present a comparison of the theoretical with the actual response, as well as techniques employed to calculate suitable correction functions that accurately predict the beam position over at least 80% of the probe's inner aperture. (Author) 4 figs., 5 refs

  12. A beam position monitor for low current dc beams

    International Nuclear Information System (INIS)

    Adderley, P.; Barry, W.; Heefner, J.; Kloeppel, P.; Rossmanith, R.; Wise, M.; Jachim, S.

    1989-01-01

    The 4 GeV recirculating linac, CEBAF, if presently under construction and will produce a CW beam with average current between.1 and 200 μA. In order to measure beam position, the beam current will be amplitude modulated at a frequency of 10 MHz. The modulation is detected by an inductive loop type monitor with electronics sensitive only to the modulation frequency. The first test with beam from the CEBAF injector indicate that beam position can be measured with an accuracy of .1 mm at a modulated beam current of 1 μA. 1 ref., 6 figs., 1 tab

  13. Design of the AGS Booster beam position monitor system

    Energy Technology Data Exchange (ETDEWEB)

    Beadle, E.; Brennan, J.M.; Ciardullo, D.J.; Savino, J.; Stanziani, V.; Thomas, R.; Van Zwienen, W.; Witkover, R.L.; Schulte, E. (Brookhaven National Lab., Upton, NY (USA); European Organization for Nuclear Research, Geneva (Switzerland))

    1989-01-01

    The AGS Booster beam position monitor system must cover a wide range of beam intensity and bunch length for proton and heavy ion acceleration. The detector is designed to maintain 0.1 mm local tolerance following 300{degree}C bakeout. The electronics will be located in the tunnel, communicating via fiber optic links to avoid ground loops. The design will be described and test results for prototype units presented. 5 refs., 4 figs.

  14. Beam based measurement of beam position monitor electrode gains

    OpenAIRE

    D. L. Rubin; M. Billing; R. Meller; M. Palmer; M. Rendina; N. Rider; D. Sagan; J. Shanks; C. Strohman

    2010-01-01

    Low emittance tuning at the Cornell Electron Storage Ring (CESR) test accelerator depends on precision measurement of vertical dispersion and transverse coupling. The CESR beam position monitors (BPMs) consist of four button electrodes, instrumented with electronics that allow acquisition of turn-by-turn data. The response to the beam will vary among the four electrodes due to differences in electronic gain and/or misalignment. This variation in the response of the BPM electrodes will couple ...

  15. Indoor Positioning and Monitoring System Using Smartphone and WLAN (IPMS

    Directory of Open Access Journals (Sweden)

    Hamid Mohammed Ali

    2015-09-01

    Full Text Available Buildings such as malls, offices, airports and hospitals nowadays have become very complicated which increases the need for a solution that helps people to find their locations in these buildings. GPS or cell signals are commonly used for positioning in an outdoor environment and are not accurate in indoor environment. Smartphones are becoming a common presence in our daily life, also the existing infrastructure, the Wi-Fi access points, which is commonly available in most buildings, has motivated this work to build hybrid mechanism that combines the APs fingerprint together with smartphone barometer sensor readings, to accurately determine the user position inside building floor relative to well-known landmarks in the floor. Also the proposed system offers a monitoring activity which lets the administrator to watch and locate certain user inside the building.The system is tested in a big building indoor environment and achieved positioning accuracies of approximately 2.1 meters.

  16. Longitudinal impedance of LHC version-1 stripline beam position monitor

    CERN Document Server

    Vos, L

    1997-01-01

    The electrodes in the first version of the LHC beam position monitor are 50 \\W striplines. An enlarged aperture is required to keep the inner face of the electrodes in the shadow of the mechanical aperture of the machine. The longitudinal impedance of this device consists of two distinct components, one from the cavity and the other from the electrodes. The cavity part of the impedance can be reduced by inter-electrode shields as proposed by G. Lambertson. A complementary way of reducing this part of the impedance is to use tapered edges. The cavity wake potential of the beam position monitor is computed both with the 3D code MAFIA and analytically for a very short bunch (20 mm) and for a normal high energy LHC bunch (75 mm). The computation is done separately for the inter-electrode shields and for the tapered ends. The agreement between the two methods is very good, hence it can be concluded that the cavity impedance of the monitor cavity is well known up to the cut-off frequency of the LHC pipe (5.1 GHz). ...

  17. Design studies on the RHIC position monitor system

    International Nuclear Information System (INIS)

    Shea, T.

    1992-09-01

    The Relativistic Heavy Ion Collider (RHIC) under construction at Brookhaven National Laboratory will consist of two superconducting storage rings 3.8 km in circumference sharing one tunnel in a side by side configuration. After injection from the existing AGS, the collider will accelerate and store a range of ion species extending from protons through gold to energies of 250 GeV for protons and 100 GeV/nucleon for fully stripped gold ions. Storage times should exceed 10 hours. As in most modem colliders the RHIC beam position monitor system is the most extensive beam diagnostic in terms of both cost and channel multiplicity. The final system will consist of approximately 500 position monitors with over 600 measurement planes of electronics. Development of this system began early so that the monitors would be available for installation into the magnet cryostats. The following document summarizes some of the efforts undertaken during the design phase of this system. Because much of this work is still in progress, the document is necessarily incomplete and some details may not reflect the final system configuration

  18. International society of sports nutrition position stand: nutrient timing

    OpenAIRE

    Kerksick, Chad M.; Arent, Shawn; Schoenfeld, Brad J.; Stout, Jeffrey R.; Campbell, Bill; Wilborn, Colin D.; Taylor, Lem; Kalman, Doug; Smith-Ryan, Abbie E.; Kreider, Richard B.; Willoughby, Darryn; Arciero, Paul J.; VanDusseldorp, Trisha A.; Ormsbee, Michael J.; Wildman, Robert

    2017-01-01

    Position statement The International Society of Sports Nutrition (ISSN) provides an objective and critical review regarding the timing of macronutrients in reference to healthy, exercising adults and in particular highly trained individuals on exercise performance and body composition. The following points summarize the position of the ISSN: Nutrient timing incorporates the use of methodical planning and eating of whole foods, fortified foods and dietary supplements. The timing of energy inta...

  19. Monitoring on internal temperature of composite insulator with embedding fiber Bragg grating for early diagnosis

    Science.gov (United States)

    Chen, Wen; Tang, Ming

    2017-04-01

    The abnormal temperature rise is the precursor of the defective composite insulator in power transmission line. However no consolidated techniques or methodologies can on line monitor its internal temperature now. Thus a new method using embedding fiber Bragg grating (FBG) in fiber reinforced polymer (FRP) rod is adopted to monitor its internal temperature. To correctly demodulate the internal temperature of FRP rod from the Bragg wavelength shift of FBG, the conversion coefficient between them is deduced theoretically based on comprehensive investigation on the thermal stresses of the metal-composite joint, as well as its material and structural properties. Theoretical model shows that the conversion coefficients of FBG embedded in different positions will be different because of non-uniform thermal stress distribution, which is verified by an experiment. This work lays the theoretical foundation of monitoring the internal temperature of composite insulator with embedding FBG, which is of great importance to its health structural monitoring, especially early diagnosis.

  20. Design, test, and calibration of an electrostatic beam position monitor

    Directory of Open Access Journals (Sweden)

    Maurice Cohen-Solal

    2010-03-01

    Full Text Available The low beta of proton or ion beams favors an electrostatic pickup to measure the transverse beam centroid position. Often papers on beam position monitors (BPM are focused on a particular aspect of the problem; however, it is important to consider all various issues of a position measurement system. Based on our experience at the IPHI (high intensity injector proton facility at CEA-Saclay, this paper will address all aspects to design, test, and calibrate a BPM for proton linear accelerators, while emphasizing the determination of the absolute beam position. We present details of the readout electronics, and describe the calibration of the BPM using a test station. For calculation and simulation of the electrical signals we developed a Mathematica script. The error analysis presented, on the basis of six BPMs installed in the high energy section of IPHI, demonstrates the expected accuracy of the position measurement. These studies also identify the parameters that could improve the performance of the beam position control. The experience from these developments is currently being used for the BPM design and test stand dedicated to the Spiral2 accelerator at Ganil-Caen which will deliver heavy ion beams.

  1. Design of position monitor module in radioactive material transport monitoring system

    International Nuclear Information System (INIS)

    Adi Abimanyu; Dwi Yuliansari N

    2013-01-01

    Aspects of safety and security of radioactive substances from the sender to the receiver is to be secured so as not to harm humans. In general, monitoring is done through conversation by telephone to determine the location and rate of exposure of radioactive substances. Through the development of science and technology makes it possible to develop a system of monitoring the transport of radioactive substances in real time by combining radiation monitor module, position monitors module and sending information nir-cable. Position monitor module developed using GPS-receiver and a micro controller ATMega8 based serial interrupts communication. Testing is done by testing communication between micro controller and GPS and also testing reading position by GPS receiver. From the test results concluded that the developed modules is good in serial communication is based on serial interrupts, good position measurement to be used outdoors and is not good enough for measurements indoors because the GPS receiver used is not using an outdoor antenna. (author)

  2. Monitoring poverty in the Philippines | IDRC - International ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    2011-07-15

    Jul 15, 2011 ... So Escaño flew from Puerto Princesa, the capital of Palawan, to Manila to visit Celia M. Reyes, Project Director for MIMAP-Philippines and Research Fellow at the Philippine Institute for Development Studies (PIDS). Launched in 1990 by the International Development Research Centre (IDRC), the Micro ...

  3. Beam position dependence of a wall-current monitor

    International Nuclear Information System (INIS)

    Tamiya, K.; Asami, A.; Suwada, T.; Urano, T.; Kobayashi, H.

    1995-01-01

    It was pointed out recently that there exists an appreciable beam position dependence in the wall-current monitor widely used in electron accelerators. Detailed study of this dependence is performed on a test bench varying the pulse width and the frequency of the input signal simulating the beam. The results of experiments show that when the pulse width becomes shorter more appreciable becomes the dependence, and it approaches to that of calculated from the method of images. A unified analysis is under way. (author)

  4. Process monitoring in international safeguards for reprocessing plants: A demonstration

    Energy Technology Data Exchange (ETDEWEB)

    Ehinger, M.H.

    1989-01-01

    In the period 1985--1987, the Oak Ridge National Laboratory investigated the possible role of process monitoring for international safeguards applications in fuel reprocessing plants. This activity was conducted under Task C.59, ''Review of Process Monitoring Safeguards Technology for Reprocessing Facilities'' of the US program of Technical Assistance to the International Atomic Energy Agency (IAEA) Safeguards program. The final phase was a demonstration of process monitoring applied in a prototypical reprocessing plant test facility at ORNL. This report documents the demonstration and test results. 35 figs.

  5. Beam based measurement of beam position monitor electrode gains

    Directory of Open Access Journals (Sweden)

    D. L. Rubin

    2010-09-01

    Full Text Available Low emittance tuning at the Cornell Electron Storage Ring (CESR test accelerator depends on precision measurement of vertical dispersion and transverse coupling. The CESR beam position monitors (BPMs consist of four button electrodes, instrumented with electronics that allow acquisition of turn-by-turn data. The response to the beam will vary among the four electrodes due to differences in electronic gain and/or misalignment. This variation in the response of the BPM electrodes will couple real horizontal offset to apparent vertical position, and introduce spurious measurements of coupling and vertical dispersion. To alleviate this systematic effect, a beam based technique to measure the relative response of the four electrodes has been developed. With typical CESR parameters, simulations show that turn-by-turn BPM data can be used to determine electrode gains to within ∼0.1%.

  6. Noise estimation of beam position monitors at RHIC

    Energy Technology Data Exchange (ETDEWEB)

    Shen, X. [Indiana Univ., Bloomington, IN (United States); Bai, M. [Brookhaven National Lab. (BNL), Upton, NY (United States). Collider-Accelerator Dept.; Lee, S. Y. [Indiana Univ., Bloomington, IN (United States)

    2014-02-10

    Beam position monitors (BPM) are used to record the average orbits and transverse turn-by-turn displacements of the beam centroid motion. The Relativistic Hadron Ion Collider (RHIC) has 160 BPMs for each plane in each of the Blue and Yellow rings: 72 dual-plane BPMs in the insertion regions (IR) and 176 single-plane modules in the arcs. Each BPM is able to acquire 1024 or 4096 consecutive turn-by-turn beam positions. Inevitably, there are broadband noisy signals in the turn-by-turn data due to BPM electronics as well as other sources. A detailed study of the BPM noise performance is critical for reliable optics measurement and beam dynamics analysis based on turn-by-turn data.

  7. Monitoring internal organ motion with continuous wave radar in CT

    International Nuclear Information System (INIS)

    Pfanner, Florian; Maier, Joscha; Allmendinger, Thomas; Flohr, Thomas; Kachelrieß, Marc

    2013-01-01

    Purpose: To avoid motion artifacts in medical imaging or to minimize the exposure of healthy tissues in radiation therapy, medical devices are often synchronized with the patient's respiratory motion. Today's respiratory motion monitors require additional effort to prepare the patients, e.g., mounting a motion belt or placing an optical reflector on the patient's breast. Furthermore, they are not able to measure internal organ motion without implanting markers. An interesting alternative to assess the patient's organ motion is continuous wave radar. The aim of this work is to design, implement, and evaluate such a radar system focusing on application in CT.Methods: The authors designed a radar system operating in the 860 MHz band to monitor the patient motion. In the intended application of the radar system, the antennas are located close to the patient's body inside the table of a CT system. One receive and four transmitting antennas are used to avoid the requirement of exact patient positioning. The radar waves propagate into the patient's body and are reflected at tissue boundaries, for example at the borderline between muscle and adipose tissue, or at the boundaries of organs. At present, the authors focus on the detection of respiratory motion. The radar system consists of the hardware mentioned above as well as of dedicated signal processing software to extract the desired information from the radar signal. The system was evaluated using simulations and measurements. To simulate the radar system, a simulation model based on radar and wave field equations was designed and 4D respiratory-gated CT data sets were used as input. The simulated radar signals and the measured data were processed in the same way. The radar system hardware and the signal processing algorithms were tested with data from ten volunteers. As a reference, the respiratory motion signal was recorded using a breast belt simultaneously with the radar measurements.Results: Concerning the

  8. Considerations of selection suggested for internal contamination monitoring in Cuba

    International Nuclear Information System (INIS)

    Cruz S, R.; Lopez B, G.; Placeres V, C.; Arado L, J.; Jova S, L.

    1996-01-01

    A method for calculating effective risk of radionuclide intake and hypothetical annual dose that will receive a person who works with unsealed sources is proposed. Calculated committed dose equivalent and metabolic characteristic of radionuclides permit to select the type of monitoring 'in vivo' and/or 'in vitro'. The method was applied to 396 workers from 28 institutions, where 20 radionuclides in 124 different products for 266 applications are used. From this study 62% of the workers had to be monitored for internal contamination, meanly by 'in vitro' monitoring. In practices of Nuclear Medicine and other medical uses 75% of the workers had to be monitored. These results permitted to corroborate the criteria for internal contamination monitoring program carried out by Center for Hygiene and Radiation Protection and permitted to identify needs for control of radionuclides intakes. (authors).5 refs., 3 figs

  9. Nonlinearities in the Response of Beam Position Monitors

    CERN Document Server

    Assmann, R W; Matheson, B; Prochnow, J

    2000-01-01

    At the LEP e+/e- collider at CERN, Geneva, a Spectrometer is used to determine the beam energy with a relative accuracy of 10-4. The Spectrometer measures the change in bending angle in a dipole magnet, the beam trajectory being obtained using beam position monitors (BPMs), which must have an accuracy close to 1 micron in order to achieve the desired precision. The BPMs used feature an aluminium block with an elliptical aperture and capacitive pickup electrodes. The response depends on the electrode geometry and also on the shape of the monitor aperture. In addition, the size of the beam itself contributes if the beam is off-centre. The beam size varies according to the beta and dispersion functions at the Spectrometer, so that each BPM may exhibit a systematic shift of the measured beam position. We have investigated the implications of such shifts on the performance of the Spectrometer. We present analytical results, a computer model of the BPM response, and comparison with measurements. The model suggest...

  10. Swimming championship finalist positions on success in international swimming competitions.

    Directory of Open Access Journals (Sweden)

    I Yustres

    Full Text Available The primary goal was to determine whether the achievement of finalist positions in the Junior Championship was associated with the achievement of success in the International Swimming Federation (FINA World Championship (WC. Secondary goals included analyzing the effect of various factors (gender, age, country, etc on swimmers' performances. Data were obtained from FINA information about the finalists from 2007 to 2015 WCs and finalists from 2006 to 2013 Junior-WCs (2400 entries. Final filtered database just included swimmers who participated in both junior and senior WCs (719 entries. A univariate general linear model (GLM was used to examine the association between time; origin (swimmer who participated in Junior WC or not; maintenance years (number of years achieving finalist positions; country; and age, adjusting for year of competition. An ordinal logistic regression (OLR model was used to identify predictors of achieving the top positions. The origin variable was not significant in either the GLM or the OLR. The only significant variables in the GLM were maintenance years (F4,706 = 7.689; p < .05 and year of competition (F4,706 = 23.239; p < .05. The OLR revealed a strong association (p < .001 between the position variable and maintenance years, getting better positions as you get more WCs (odds = 1.85. In conclusion, no evidence was obtained to conclude finalist position in Junior WC have influence in achieve success in FINA WC. Maintenance years in WCs have a positive impact to achieve better positions.

  11. The Coo Effect in the International Brand Positioning Strategy

    Directory of Open Access Journals (Sweden)

    Barbara Kobuszewski Volles

    2016-12-01

    Full Text Available Abstract Purpose: This study aims to develop a model in order to understand how Chinese companies strategically position their brands, considering the causes of the country of origin (COO effect, when going through the process of internationalization. Design/methodology/approach: The study approach a qualitative case study that incorporates two different Chinese companies with subsidiaries settled in Brazil. It was conducted depth interviews with different components of the studied firms. Findings: In this way, it was developed a model that try to explain the positive and/or negative effect of general attributes from China (labor market, institution framework and education on the brand positioning divers (value preposition, points of leverage, primary target and image reinforcement, which influences on the cost-benefit strategy approach of the brands when positioning internationally. Research limitations/implications: Considering that this research is a qualitative study of two Chinese companies, further qualitative and quantitative studies would be fruitful to the validity of the presented model. Originality/value: In order to contribute to the academic field, it was found that this research present a unique model considering different causes of the COO effect that might affect the international branding positioning.

  12. Beam position monitor system of J-PARC RCS

    Energy Technology Data Exchange (ETDEWEB)

    Hayashi, N., E-mail: naoki.hayashi@j-parc.jp [Accelerator Division, J-PARC Center, Japan Atomic Energy Agency (JAEA), Tokai, Naka, Ibaraki 319-1195 (Japan); Kawase, M.; Hatakeyama, S.; Hiroki, S.; Saeki, R.; Takahashi, H.; Teruyama, Y.; Toyokawa, R. [Accelerator Division, J-PARC Center, Japan Atomic Energy Agency (JAEA), Tokai, Naka, Ibaraki 319-1195 (Japan); Arakawa, D.; Hiramatsu, S.; Lee, S.; Satou, K.; Tejima, M.; Toyama, T. [High Energy Accelerator Research Organization (KEK), Tsukuba, Ibaraki 305-0801 (Japan)

    2012-06-11

    The J-PARC RCS is a 25 Hz Rapid-Cycling proton Synchrotron and its designed beam power is 1 MW. The beam position monitor (BPM) system at J-PARC RCS is described in this paper. The pre-defined diameter of the BPM detectors is larger than 250 mm, however, the system has to measure the beam position very accurately. In addition, it is necessary to have a large dynamic range. The system should work not only for the high intensity but also for low intensity, such as during beam commissioning, when the intensity is below 1% of the design intensity. There are 54 BPM detectors around the ring and most of them are placed inside steering magnets because of quite limited space. The BPM detector is an electro-static type and it has four electrodes, and a pair of electrodes gives a good linear response with a diagonal cut shape to detect the charge center precisely. The signal processing units, which are equipped with 14-bit 40 MS/s ADC and 600 MHz DSP, have been developed. They are accessed via shared memory space and controlled by EPICS. Such a processing unit is capable of recording the full 25 Hz pulse data for the so-called 'COD mode' (averaged beam position calculation) and it can also store the whole waveform data for further analysis, like turn-by-turn position calculation. The resolution was estimated to be 20{mu}m for 'COD mode' and to be 0.3 mm for the turn-by-turn mode with relatively low intensity of 8 Multiplication-Sign 10{sup 11}ppp. The position accuracy is estimated to be about 0.5 mm using a newly developed Beam Based Alignment (BBA) method.

  13. Digital beam position monitor for the HAPPEX experiment

    Energy Technology Data Exchange (ETDEWEB)

    Sherlon Kauffman; John Musson; Hai Dong; Lisa Kaufman; Arne Freyberger

    2005-05-01

    The proposed HAPPEX experiment at CEBAF employs a three cavity monitor system for high precision (1um), high bandwidth (100 kHz) position measurements. This is performed using a cavity triplet consisting of two TM110-mode cavities (one each for X and Y planes) combined with a conventional TM010-mode cavity for a phase and magnitude reference. Traditional systems have used the TM010 cavity output to directly down convert the BPM cavity signals to base band. The multi-channel HAPPEX digital receiver simultaneously I/Q samples each cavity and extracts position using a CORDIC algorithm. The hardware design consists of a RF receiver daughter board and a digital processor motherboard that resides in a VXI crate. The daughter board down converts 1.497 GHz signals from the TM010 cavity and X and Y signals from the TM110 cavities to 3 MHz and extracts the quadrature digital signals. The motherboard processes this data and computes beam intensity and X-Y positions with resolution of 1um, 100 kHz output bandwidth, and overall latency of 1us. The results are available in both the analog and digital format.

  14. Digital Beam Position Monitor for the Happex Experiment

    Energy Technology Data Exchange (ETDEWEB)

    S.R. Kauffman; H. Dong; A. Freyberger; L. Kaufman; J. Musson

    2005-05-16

    The proposed HAPPEX experiment at CEBAF employs a three cavity monitor system for high-precision (1 mm), high-bandwidth (100 kHz) position measurements. This is performed using a cavity triplet consisting of two TM110-mode cavities (one each for X and Y planes) combined with a conventional TM-010-mode cavity for a phase and magnitude reference. Traditional systems have used the TM010 cavity output to directly down convert the BPM cavity signals to base band. The Multi-channel HAPPEX digital receiver simultaneously I/Q samples each cavity and extracts position using a CORDIC algorithm. The hardware design consists of a digital receiver daughter board and digital processor motherboard that resides in a VXI crate. The daughter board down converts 1.497 GHz signals from the TM010 cavity and X and Y signals from the TM110 cavities to 4 MHz, and extracts the quadrature digital signals. The motherboard processes this data and computes beam intensity and X-Y positions with a resolution of one mm, 100 kHz output bandwidth, and overall latency of ten microseconds. The results are available in both analog and digital format.

  15. Swimming championship finalist positions on success in international swimming competitions.

    Science.gov (United States)

    Yustres, I; Martín, R; Fernández, L; González-Ravé, J M

    2017-01-01

    The primary goal was to determine whether the achievement of finalist positions in the Junior Championship was associated with the achievement of success in the International Swimming Federation (FINA) World Championship (WC). Secondary goals included analyzing the effect of various factors (gender, age, country, etc) on swimmers' performances. Data were obtained from FINA information about the finalists from 2007 to 2015 WCs and finalists from 2006 to 2013 Junior-WCs (2400 entries). Final filtered database just included swimmers who participated in both junior and senior WCs (719 entries). A univariate general linear model (GLM) was used to examine the association between time; origin (swimmer who participated in Junior WC or not); maintenance years (number of years achieving finalist positions); country; and age, adjusting for year of competition. An ordinal logistic regression (OLR) model was used to identify predictors of achieving the top positions. The origin variable was not significant in either the GLM or the OLR. The only significant variables in the GLM were maintenance years (F4,706 = 7.689; p getting better positions as you get more WCs (odds = 1.85). In conclusion, no evidence was obtained to conclude finalist position in Junior WC have influence in achieve success in FINA WC. Maintenance years in WCs have a positive impact to achieve better positions.

  16. The equivalent internal orientation and position noise for contour integration.

    Science.gov (United States)

    Baldwin, Alex S; Fu, Minnie; Farivar, Reza; Hess, Robert F

    2017-10-12

    Contour integration is the joining-up of local responses to parts of a contour into a continuous percept. In typical studies observers detect contours formed of discrete wavelets, presented against a background of random wavelets. This measures performance for detecting contours in the limiting external noise that background provides. Our novel task measures contour integration without requiring any background noise. This allowed us to perform noise-masking experiments using orientation and position noise. From these we measure the equivalent internal noise for contour integration. We found an orientation noise of 6° and position noise of 3 arcmin. Orientation noise was 2.6x higher in contour integration compared to an orientation discrimination control task. Comparing against a position discrimination task found position noise in contours to be 2.4x lower. This suggests contour integration involves intermediate processing that enhances the quality of element position representation at the expense of element orientation. Efficiency relative to the ideal observer was lower for the contour tasks (36% in orientation noise, 21% in position noise) compared to the controls (54% and 57%).

  17. OMINEX: Survey of internal dose monitoring programmes for radiation workers

    International Nuclear Information System (INIS)

    Rahola, T.; Etherington, G.; Berard, P.; Le Guen, B.; Hurtgen, C.

    2003-01-01

    Monitoring of the workforce in the nuclear industries is carried out primarily in order to demonstrate compliance with European Union (EU) legislation and the Basic Safety Standards for the protection of the health of workers against the dangers arising from ionising radiation recommended by the International Atomic Energy Agency (IAEA). There is, however, no common strategy for internal dose monitoring programmes currently in use in the EU countries. Surveys have been carried out in which organisations were asked to provide information on the design of their internal dose monitoring programmes and on the costs of these programmes. Information was requested from both EU countries and Associated States. Databases for storage and reporting of all gained information were constructed, and results from the surveys have been compiled. This work was carried out within the EC 5th Framework Programme project, OMINEX, which aims to provide advice and guidance on designing and implementing internal dose monitoring programmes in the workplace in such a way that best use is made of available resources, while minimising costs. (author)

  18. Applying EVM principles to Tevatron Beam Position Monitor Project

    International Nuclear Information System (INIS)

    Banerjee, Bakul

    2005-01-01

    At Fermi National Accelerator Laboratory (Fermilab), the Tevatron high energy particle collider must meet the increasing scientific demand of higher beam luminosity. To achieve this higher luminosity goal, U. S. Department of Energy (DOE) sponsored a major upgrade of capabilities of Fermilab's accelerator complex that spans five years and costs over fifty million dollars. Tevatron Beam Position Monitor (BPM) system upgrade is a part of this project, generally called RunII upgrade project. Since the purpose of the Tevatron collider is to detect the smashing of proton and anti-protons orbiting the circular accelerator in opposite directions, capability to detect positions of both protons and antiprotons at a high resolution level is a desirable functionality of the monitoring system. The original system was installed during early 1980s, along with the original construction of the Tevatron. However, electronic technology available in 1980s did not allow for the detection of significantly smaller resolution of antiprotons. The objective of the upgrade project is to replace the existing BPM system with a new system utilizing capabilities of modern electronics enhanced by a front-end software driven by a real-time operating software. The new BPM system is designed to detect both protons and antiprotons with increased resolution of up to an order of magnitude. The new system is capable of maintaining a very high-level of data integrity and system reliability. The system consists of 27 VME crates installed at 27 service buildings around the Tevatron ring servicing 236 beam position monitors placed underground, inside the accelerator tunnel. Each crate consists of a single Timing Generator Fanout module, custom made by Fermilab staff, one MVME processor card running VxWorks 5.5, multiple Echotek Digital Receiver boards complimented by custom made Filter Board. The VxWorks based front-end software communicates with the Main Accelerator Control software via a special

  19. Brazilian participation in the International Monitoring System for Nuclear Explosions

    International Nuclear Information System (INIS)

    Veloso, Jose Alberto Vivas

    1995-01-01

    On January 1, 1995, Brazil was integrated to the world-wide seismic system, through the Seismological Observatory of the University of Brasilia, dedicated to detect and identify underground nuclear explosions. This is an unprecedented global effort program to conduct a seismic test of rapid data collection, distribution and processing evolving the most advanced sensors, global communications and data processing technologies. By the end of February, 49 countries were incorporated and the present test represents a first training step towards the final definition of an International Monitoring System to monitoring a Comprehensive test Band Treaty. Besides accomplishing its main goal, the global monitoring program will be able to supply rapidly, through the International Data Center, important information to the seismological community. (author). 2 figs

  20. Cycle 24 COS FUV Internal/External Wavelength Scale Monitor

    Science.gov (United States)

    Fischer, William J.

    2018-02-01

    We report on the monitoring of the COS FUV wavelength scale zero-points during Cycle 24 in program 14855. Select cenwaves were monitored for all FUV gratings at Lifetime Position 3. The target and cenwaves have remained the same since Cycle 21, with a change only to the target acquisition sequence. All measured offsets are within the error goals, although the G140L cenwaves show offsets at the short-wavelength end of segment A that are approaching the tolerance. This behavior will be closely monitored in subsequent iterations of the program.

  1. Atomics International environmental monitoring and facility effluent annual report, 1976

    International Nuclear Information System (INIS)

    Moore, J.D.

    1977-01-01

    Environmental and facility effluent radioactivity monitoring at Atomics International (AI) is performend by the Radiation and Nuclear Safety Unit of the Health, Safety, and Radiation Services Department. Soil, vegetation, and surface water are routinely sampled to a distance of 10 miles from AI sites. Continuous ambient air sampling and thermoluminescent dosimetry are performed on site for monitoring airborne radioactivity and site ambient radiation levels. Radioactivity in effluents discharged to the atmosphere from AI facilities is continuously sampled and monitored to ensure that levels released to unrestricted areas are within appropriate limits, and to identify processes which may require additional engineering safeguards to minimize radioactivity levels in such effluents. In addition, selected nonradioactive constituents in surface water discharged to unrestricted areas are determined. This report summarizes and discusses monitoring results for 1976. The results of a special soil plutonium survey performed during the year are also summarized

  2. International Symposium on Monitoring Behavior and Supervisory Control

    CERN Document Server

    Johannsen, Gunnar

    1976-01-01

    This book includes all papers presented at the International Symposium on Monitoring Behavior and Supervisory Control held at Berchtesgaden, Federal Republic of Germany, March 8-12, 1976. The Symposium was sponsored by the Scientific Affairs Division of the North Atlantic Treaty Organization, Brussels, and the government of the Federal Republic of Germany, Bonn. We believe the book constitutes an important and timely status report on monitoring behavior and supervisory control by human operators of complex man-machine systems in which the computer is sharing key functions with the man. These systems include aircraft and other vehicles, nuclear and more conventional power plants, and processes for the manu­ facture of chemicals, petroleum, and discrete parts. By "monitoring" we mean the systematic observation by a human operator of mul tiple sources of information, e. g. , ranging from integrated display consoles to disparate "live situations". The monitor's purpose is to determine whether operations are norm...

  3. Readout ASIC of pair-monitor for international linear collider

    International Nuclear Information System (INIS)

    Sato, Yutaro; Ikeda, Hirokazu; Ito, Kazutoshi; Miyamoto, Akiya; Nagamine, Tadashi; Sasaki, Rei; Takubo, Yosuke; Tauchi, Toshiaki; Yamamoto, Hitoshi

    2010-01-01

    The pair-monitor is a beam profile monitor at the interaction point of the international linear collider. A prototype of the readout ASIC for the pair-monitor has been designed and tested. Since the pair-monitor uses the hit distribution of electrons and positrons generated by the beam-crossing to measure the beam profile, the readout ASIC is designed to count the number of hits. In a prototype ASIC, 36 readout cells were implemented by TSMC 0.25-μm CMOS process. Each readout cell is equipped with an amplifier, comparator, 8-bit counter and 16 count-registers. By the operation test, all the ASIC component were confirmed to work correctly. As the next step, we develop the prototype ASIC with the silicon on insulator technology. It is produced with OKI 0.2-μm FD-SOI CMOS process.

  4. Internal maternal position of women who became pregnant using IVF

    Directory of Open Access Journals (Sweden)

    Vera A. Yakupova

    2015-03-01

    Full Text Available Nowadays in vitro fertilization procedure is widespread. Due to improvements in medical technology parenting has become possible for couples who were doomed to childlessness. Practical request for psychological support couples who have decided to take part in the IVF program has been raised. Shaping the internal position of the IVF parent takes place in special psychological conditions. The IVF procedure is preceded by a period of infertility, the procedure is often the last chance to have a baby alone. Participation in the IVF program involves regular contact with doctors, medical personnel access to the intimate sphere of life couples. The paper analyzes the attitude of women participating in the IVF pregnancy program, the unborn baby and parenting - the elements constituting the parent position. The study which was attended by 224 pregnant women, 62 participants of IVF program and 162 women with physiological pregnancy was carried out on the basis of Kulakov Scientific Centre for Obstetrics, Gynecology and Perinatology. When analyzing the data obtained we were able to identify features of the internal position of women who became pregnant using IVF. In comparison with a group of women with physiological pregnancy, the IVF program participants tend to romanticize the role of parent and child. IVF program participants demonstrate unwillingness to take on the role of parent. The main motivation of mothers in the IVF group concentrated on the very fact of pregnancy and childbirth, proper parenting, while care and support for children is not appealing to women who became pregnant using IVF. Important conditions for becoming a parent are the experience of motherhood and the time of pregnancy expectation.

  5. Development of Web based system for individual internal monitoring programme

    International Nuclear Information System (INIS)

    Lima, Vanessa Rogeria de

    2007-01-01

    The purposes of the internal monitoring, in general, are to verify and document that each worker is protected adequately against risks from radionuclide intakes and the protection complies with legal requirements. Therefore, an overall radiation protection programme, starts with an assessment to identify work situations in which there is a risk of internal contamination of workers and to quantify the likely intake of radioactive material and the resulting committed effective dose. As a part of a continuous improvement of the monitoring programme for occupationally exposed workers at IPEN, it is being developed a Web based system to access the internal dosimetry database. The system was implemented using Hypertext Preprocessor, PHP, and a PostgreSQL database. This system will introduce a new paradigm in the routine of the internal dosimetry service, providing a fast access to the information among the measurement laboratories staff, dose evaluation group and the radiation protection supervisor. The database maintains information about worker identification, physical and chemical characteristics of the radionuclide, type of monitoring, measurement data and the dose. Moreover, this information will be readily available to provide support for regulatory compliance and quality control requirements. (author)

  6. GSETT-3: testing the experimental international seismic monitoring system

    International Nuclear Information System (INIS)

    Ringdal, Frode

    1995-01-01

    Global seismic monitoring system has been developed by the Conference on Disarmaments (CDs) ad hoc group of scientific experts to consider international cooperative measures to detect and identify seismic events (the GSE), based in Geneva. In the course of its work, the GSE has conducted two large-scale global technical tests, Global Seismic Events Technical Test-1 (GSETT-1) in 1984 and GSETT-2 in 1991. The GSE has now embarked upon its third and most ambitious technical test, GSETT-3, which will encompass the development, testing and evaluation of a working prototype of the eventual Comprehensive Test Ban Treaty (CTBT) seismic monitoring system

  7. Position-sensitive radiation monitoring (surface contamination monitor). Innovative technology summary report

    International Nuclear Information System (INIS)

    1999-06-01

    The Shonka Research Associates, Inc. Position-Sensitive Radiation Monitor both detects surface radiation and prepares electronic survey map/survey report of surveyed area automatically. The electronically recorded map can be downloaded to a personal computer for review and a map/report can be generated for inclusion in work packages. Switching from beta-gamma detection to alpha detection is relatively simple and entails moving a switch position to alpha and adjusting the voltage level to an alpha detection level. No field calibration is required when switching from beta-gamma to alpha detection. The system can be used for free-release surveys because it meets the federal detection level sensitivity limits requires for surface survey instrumentation. This technology is superior to traditionally-used floor contamination monitor (FCM) and hand-held survey instrumentation because it can precisely register locations of radioactivity and accurately correlate contamination levels to specific locations. Additionally, it can collect and store continuous radiological data in database format, which can be used to produce real-time imagery as well as automated graphics of survey data. Its flexible design can accommodate a variety of detectors. The cost of the innovative technology is 13% to 57% lower than traditional methods. This technology is suited for radiological surveys of flat surfaces at US Department of Energy (DOE) nuclear facility decontamination and decommissioning (D and D) sites or similar public or commercial sites

  8. Internal city marketing: Positive activation of inhabitants through supported voluntarism

    Directory of Open Access Journals (Sweden)

    Irena Ograjenšek

    2015-03-01

    Full Text Available Urban settlements which were planned and established during the socialist period either in their entirety or partially (in form of fast-growing districts can be found all over Central and Eastern Europe. In most of them authorities have been fighting numerous economic and social problems, many either caused by, or stemming from, lack of social cohesion. One visible sign of such problems are neglected public spaces, often doomed to be in a poor condition due to lack of co-ordinated action. In this paper we demonstrate the importance of social capital and public administration’s courage and creativity when applying the tools of internal city marketing for what we call ‘supported voluntarism’ aimed at positive transformation of public spaces in a post-socialist residential neighbourhood using the Slovenian post-socialist city of Velenje as a showcase.

  9. The CTBT : New Zealand's involvement in the international monitoring system

    International Nuclear Information System (INIS)

    Matthews, M.

    1998-01-01

    The Comprehensive Test-Ban Treaty (CTBT), to which most countries are now signatories, is seen as a major step towards the curtailment of nuclear weapons production and eventual disarmament. The Treaty can only be effectively implemented, however, if there is a monitoring system in place to verify that weapons testing is not taking place and, if it does occur, to identify the violator. The diesign of the International Monitoring System (IMS) has therefore been a significant part of the Treaty negotiations. This article focuses o New Zealand's involvement in the IMS, in atmospheric radioactivity and infrasound monitoring. Because of its history of involvement in environmental monitoring, National Radiation Laboratory (NRL) has been providing expert input into Treaty negotiations concerning the radionucled component of the IMS. The Institute of Geological and Nuclear Sciences (IGNS) monitors seismic activity at a number of locations in New Zealand and the South Pacific, and has also provided expert input to the design of the global seismic component of the IMS. The New Zealand government has offered the monitoring facilities of NRL and IGNS for inclusion in the global IMS. (author)

  10. International conference on individual monitoring of ionising radiation

    International Nuclear Information System (INIS)

    Vanhavere, Filip

    2016-01-01

    This special issue of the journal Radiation Protection Dosimetry is dedicated to the Proceedings of the International Conference on Individual Monitoring of Ionising Radiation (IM2015), which is the fifth of a series of conferences dealing with individual monitoring. This conference series is initiated by EURADOS, the European Radiation Dosimetry Group, and is organised every 5 years. In 2015, the conference was jointly organised by the Belgian Nuclear Research Centre (SCK.CEN), AV Controlatom, and the Vrije Universiteit Brussel. It brought together scientists from regulatory authorities, individual monitoring services (IMS), research bodies, European networks and companies, for the purpose of facilitating the dissemination of knowledge, exchanging experiences and promoting new ideas in the field of individual monitoring. After the conference, 124 papers were submitted for publication in these peer-reviewed proceedings. From these, 103 were finally accepted for publication. The help of the numerous referees and the guest editors is very much appreciated. These proceedings provide a full image of the IM2015 conference. The high-level publications will be useful to improve the state of individual monitoring all over the world and aim to inspire many scientists to continue their work on a better monitoring of radiologically exposed workers

  11. Global Positioning System (GPS) civil signal monitoring (CSM) trade study report

    Science.gov (United States)

    2014-03-07

    This GPS Civil Signal Monitoring (CSM) Trade Study has been performed at the direction of DOT/FAA Navigation Programs as the agency of reference for consolidating civil monitoring requirements on the Global Positioning System (GPS). The objective of ...

  12. A Vision of International Drought Monitoring Among Pacific Rim Nations

    Science.gov (United States)

    Lawrimore, J. H.; Heim, R. R.

    2008-05-01

    Drought is an environmental hazard which results in billions of dollars in economic losses as well as societal suffering and increased mortality in many parts of the world each year. No country is immune from its effects and there is documented evidence of an increasing trend in droughts in many regions since the 1970s. There is also a high likelihood of droughts affecting an ever larger proportion of the world as global temperatures continue to rise. This reality along with the wide-ranging societal and economic impacts of drought upon the world's countries calls out for coordinated international drought monitoring and response. A demonstration of the potential for contributions through international collaboration was made through the establishment of a North American Drought Monitor (NADM) partnership between the United States, Mexico, and Canada in 2002. The United States has also recently initiated development of a National Integrated Drought Information System (NIDIS) to coordinate drought monitoring, mitigation, and research activities at federal, state, and local levels within the United States. Building on the successes and lessons learned from these ongoing activities, efforts are now underway to foster linkages with other countries throughout both North and South America and the Pacific region as an early step toward establishment of a global drought early warnings system. Through the Group on Earth Observations (GEO) new partnerships are supporting the development of a drought monitoring system in the Pacific Rim. Countries in this region are linked by the strong influence of El Niño and La Niña, leading to periods of severe, persistent, and widespread drought, alternating with periods of heavy rain and flooding. As such, the Pacific Rim makes an ideal laboratory for addressing the challenge of drought early warning through capacity building supported by improved drought monitoring tools and data sharing principles.

  13. Impact of the internal contamination monitoring for national and international regulations

    International Nuclear Information System (INIS)

    Gaburo, J.C.; Sordi, G.M.

    1996-01-01

    An evaluation of the internal radiation dose received by workers between 1984 and 1994 was performed, after a brief description of IPEN facility. The National and International Recommendation aims to reduce the workers' doses below 1/10 of the annual limits. The routine monitoring should be eliminated, if the individual annual dose is below 3/10 of the annual limits. In this case, only the operational monitoring should be maintained. In principle, the concept of restricted area should be reviewed, because, according to Publication 26 of ICRP, 1977, it should be a supervised area instead. The new concept of restricted area recommended by the Publication 60, ICRP 1991, should be adjusted accordingly. Thus, the classification used by the Commission-controlled areas and supervised areas will be with the foreseeable dose and not with the actual dose. When the individual annual dose is kept below 1/10 of the annual limits, the routine monitoring is not necessary, and only operational monitoring is needed. Finally, the future possible activities of the Individual Internal Dosimetry Laboratory at IPEN are discussed, after the elimination of individual monitoring. (authors). 8 refs

  14. Position of Serbia on the international market of alcoholic beverages

    Directory of Open Access Journals (Sweden)

    Đorović Milutin

    2012-01-01

    Full Text Available This paper presents a comparative analysis of the major indicators of both the world and domestic markets of alcoholic beverages. Namely, for the last 21 years, for the observed subperiods, the method of comparative analysis were used to study quantitative and structural differences in the production and trade of analyzed product groups, at both the world and at the level of continents and some countries. The leading manufacturers and flows of international trade and the leading exporters and importers of wine, beer and distilled alcoholic beverages were defined, with special emphasis on the importance of Serbia, i.e. its position in the global market for all these products. Pursuant to the above, and importance of analyzed product groups for the domestic market, i.e. agroindustry and the economy as a whole, this paper specially studies balances, structure, dynamics and regional orientation of foreign trade exchange in wine, beer, and distilled alcoholic beverages. In addition, the paper points to the needs, capabilities, measures and directions of further development of domestic production and export of products analyzed.

  15. GENASIS national and international monitoring networks for persistent organic pollutants

    Science.gov (United States)

    Brabec, Karel; Dušek, Ladislav; Holoubek, Ivan; Hřebíček, Jiří; Kubásek, Miroslav; Urbánek, Jaroslav

    2010-05-01

    Persistent organic pollutants (POPs) remain in the centre of scientific attention due to their slow rates of degradation, their toxicity, and potential for both long-range transport and bioaccumulation in living organisms. This group of compounds covers large number of various chemicals from industrial products, such as polychlorinated biphenyls, etc. The GENASIS (Global Environmental Assessment and Information System) information system utilizes data from national and international monitoring networks to obtain as-complete-as-possible set of information and a representative picture of environmental contamination by persistent organic pollutants (POPs). There are data from two main datasets on POPs monitoring: 1.Integrated monitoring of POPs in Košetice Observatory (Czech Republic) which is a long term background site of the European Monitoring and Evaluation Programme (EMEP) for the Central Europe; the data reveals long term trends of POPs in all environmental matrices. The Observatory is the only one in Europe where POPs have been monitored not only in ambient air, but also in wet atmospheric deposition, surface waters, sediments, soil, mosses and needles (integrated monitoring). Consistent data since the year 1996 are available, earlier data (up to 1998) are burdened by high variability and high detection limits. 2.MONET network is ambient air monitoring activities in the Central and Eastern European region (CEEC), Central Asia, Africa and Pacific Islands driven by RECETOX as the Regional Centre of the Stockholm Convention for the region of Central and Eastern Europe under the common name of the MONET networks (MONitoring NETwork). For many of the participating countries these activities generated first data on the atmospheric levels of POPs. The MONET network uses new technologies of air passive sampling, which was developed, tested, and calibrated by RECETOX in cooperation with Environment Canada and Lancaster University, and was originally launched as a

  16. Lateralization of the posterior parietal cortex for internal monitoring of self- versus externally generated movements.

    Science.gov (United States)

    Ogawa, Kenji; Inui, Toshio

    2007-11-01

    Internal monitoring or state estimation of movements is essential for human motor control to compensate for inherent delays and noise in sensorimotor loops. Two types of internal estimation of movements exist: self-generated movements, and externally generated movements. We used functional magnetic resonance imaging to investigate differences in brain activity for internal monitoring of self- versus externally generated movements during visual occlusion. Participants tracked a sinusoidally moving target with a mouse cursor. On some trials, vision of either target (externally generated) or cursor (self-generated) movement was transiently occluded, during which subjects continued tracking by estimating current position of either the invisible target or cursor on screen. Analysis revealed that both occlusion conditions were associated with increased activity in the presupplementary motor area and decreased activity in the right lateral occipital cortex compared to a control condition with no occlusion. Moreover, the right and left posterior parietal cortex (PPC) showed greater activation during occlusion of target and cursor movements, respectively. This study suggests lateralization of the PPC for internal monitoring of internally versus externally generated movements, fully consistent with previously reported clinical findings.

  17. International remote monitoring project Argentina Nuclear Power Station Spent Fuel Transfer Remote Monitoring System

    Energy Technology Data Exchange (ETDEWEB)

    Schneider, S.; Lucero, R.; Glidewell, D. [and others

    1997-08-01

    The Autoridad Regulataria Nuclear (ARN) and the United States Department of Energy (DOE) are cooperating on the development of a Remote Monitoring System for nuclear nonproliferation efforts. A Remote Monitoring System for spent fuel transfer will be installed at the Argentina Nuclear Power Station in Embalse, Argentina. The system has been designed by Sandia National Laboratories (SNL), with Los Alamos National Laboratory (LANL) and Oak Ridge National Laboratory (ORNL) providing gamma and neutron sensors. This project will test and evaluate the fundamental design and implementation of the Remote Monitoring System in its application to regional and international safeguards efficiency. This paper provides a description of the monitoring system and its functions. The Remote Monitoring System consists of gamma and neutron radiation sensors, RF systems, and video systems integrated into a coherent functioning whole. All sensor data communicate over an Echelon LonWorks Network to a single data logger. The Neumann DCM 14 video module is integrated into the Remote Monitoring System. All sensor and image data are stored on a Data Acquisition System (DAS) and archived and reviewed on a Data and Image Review Station (DIRS). Conventional phone lines are used as the telecommunications link to transmit on-site collected data and images to remote locations. The data and images are authenticated before transmission. Data review stations will be installed at ARN in Buenos Aires, Argentina, ABACC in Rio De Janeiro, IAEA Headquarters in Vienna, and Sandia National Laboratories in Albuquerque, New Mexico. 2 refs., 2 figs.

  18. International Society of Sports Nutrition position stand: energy drinks

    Science.gov (United States)

    2013-01-01

    Position Statement: The International Society of Sports Nutrition (ISSN) bases the following position stand on a critical analysis of the literature on the safety and efficacy of the use of energy drinks (ED) or energy shots (ES). The ISSN has concluded the following. 1. Although ED and ES contain a number of nutrients that are purported to affect mental and/or physical performance, the primary ergogenic nutrients in most ED and ES appear to be carbohydrate and/or caffeine. 2. The ergogenic value of caffeine on mental and physical performance has been well-established but the potential additive benefits of other nutrients contained in ED and ES remains to be determined. 3. Consuming ED 10-60 minutes before exercise can improve mental focus, alertness, anaerobic performance, and/or endurance performance. 4. Many ED and ES contain numerous ingredients; these products in particular merit further study to demonstrate their safety and potential effects on physical and mental performance. 5. There is some limited evidence that consumption of low-calorie ED during training and/or weight loss trials may provide ergogenic benefit and/or promote a small amount of additional fat loss. However, ingestion of higher calorie ED may promote weight gain if the energy intake from consumption of ED is not carefully considered as part of the total daily energy intake. 6. Athletes should consider the impact of ingesting high glycemic load carbohydrates on metabolic health, blood glucose and insulin levels, as well as the effects of caffeine and other stimulants on motor skill performance. 7. Children and adolescents should only consider use of ED or ES with parental approval after consideration of the amount of carbohydrate, caffeine, and other nutrients contained in the ED or ES and a thorough understanding of the potential side effects. 8. Indiscriminant use of ED or ES, especially if more than one serving per day is consumed, may lead to adverse events and harmful side effects. 9

  19. International Society of Sports Nutrition position stand: energy drinks

    Directory of Open Access Journals (Sweden)

    Campbell Bill

    2013-01-01

    Full Text Available Abstract Position Statement: The International Society of Sports Nutrition (ISSN bases the following position stand on a critical analysis of the literature on the safety and efficacy of the use of energy drinks (ED or energy shots (ES. The ISSN has concluded the following. 1. Although ED and ES contain a number of nutrients that are purported to affect mental and/or physical performance, the primary ergogenic nutrients in most ED and ES appear to be carbohydrate and/or caffeine. 2. The ergogenic value of caffeine on mental and physical performance has been well-established but the potential additive benefits of other nutrients contained in ED and ES remains to be determined. 3. Consuming ED 10-60 minutes before exercise can improve mental focus, alertness, anaerobic performance, and/or endurance performance. 4. Many ED and ES contain numerous ingredients; these products in particular merit further study to demonstrate their safety and potential effects on physical and mental performance. 5. There is some limited evidence that consumption of low-calorie ED during training and/or weight loss trials may provide ergogenic benefit and/or promote a small amount of additional fat loss. However, ingestion of higher calorie ED may promote weight gain if the energy intake from consumption of ED is not carefully considered as part of the total daily energy intake. 6. Athletes should consider the impact of ingesting high glycemic load carbohydrates on metabolic health, blood glucose and insulin levels, as well as the effects of caffeine and other stimulants on motor skill performance. 7. Children and adolescents should only consider use of ED or ES with parental approval after consideration of the amount of carbohydrate, caffeine, and other nutrients contained in the ED or ES and a thorough understanding of the potential side effects. 8. Indiscriminant use of ED or ES, especially if more than one serving per day is consumed, may lead to adverse events and

  20. International Society of Sports Nutrition position stand: energy drinks.

    Science.gov (United States)

    Campbell, Bill; Wilborn, Colin; La Bounty, Paul; Taylor, Lem; Nelson, Mike T; Greenwood, Mike; Ziegenfuss, Tim N; Lopez, Hector L; Hoffman, Jay R; Stout, Jeffrey R; Schmitz, Stephen; Collins, Rick; Kalman, Doug S; Antonio, Jose; Kreider, Richard B

    2013-01-03

    Position Statement: The International Society of Sports Nutrition (ISSN) bases the following position stand on a critical analysis of the literature on the safety and efficacy of the use of energy drinks (ED) or energy shots (ES). The ISSN has concluded the following. 1. Although ED and ES contain a number of nutrients that are purported to affect mental and/or physical performance, the primary ergogenic nutrients in most ED and ES appear to be carbohydrate and/or caffeine. 2. The ergogenic value of caffeine on mental and physical performance has been well-established but the potential additive benefits of other nutrients contained in ED and ES remains to be determined. 3. Consuming ED 10-60 minutes before exercise can improve mental focus, alertness, anaerobic performance, and/or endurance performance. 4. Many ED and ES contain numerous ingredients; these products in particular merit further study to demonstrate their safety and potential effects on physical and mental performance. 5. There is some limited evidence that consumption of low-calorie ED during training and/or weight loss trials may provide ergogenic benefit and/or promote a small amount of additional fat loss. However, ingestion of higher calorie ED may promote weight gain if the energy intake from consumption of ED is not carefully considered as part of the total daily energy intake. 6. Athletes should consider the impact of ingesting high glycemic load carbohydrates on metabolic health, blood glucose and insulin levels, as well as the effects of caffeine and other stimulants on motor skill performance. 7. Children and adolescents should only consider use of ED or ES with parental approval after consideration of the amount of carbohydrate, caffeine, and other nutrients contained in the ED or ES and a thorough understanding of the potential side effects. 8. Indiscriminant use of ED or ES, especially if more than one serving per day is consumed, may lead to adverse events and harmful side effects. 9

  1. FRAX® International Task Force of the 2010 Joint International Society for Clinical Densitometry & International Osteoporosis Foundation Position Development Conference.

    Science.gov (United States)

    Cauley, Jane A; El-Hajj Fuleihan, Ghada; Luckey, Marjorie M

    2011-01-01

    Osteoporosis is a serious worldwide epidemic. FRAX® is a web-based tool developed by the Sheffield WHO Collaborating Center team, that integrates clinical risk factors and femoral neck BMD and calculates the 10 year fracture probability in order to help health care professionals identify patients who need treatment. However, only 31 countries have a FRAX® calculator. In the absence of a FRAX® model for a particular country, it has been suggested to use a surrogate country for which the epidemiology of osteoporosis most closely approximates the index country. More specific recommendations for clinicians in these countries are not available. In North America, concerns have also been raised regarding the assumptions used to construct the US ethnic specific FRAX® calculators with respect to the correction factors applied to derive fracture probabilities in Blacks, Asians and Hispanics in comparison to Whites. In addition, questions were raised about calculating fracture risk in other ethnic groups e.g., Native Americans and First Canadians. The International Society for Clinical Densitometry (ISCD) in conjunction with the International Osteoporosis Foundation (IOF) assembled an international panel of experts that ultimately developed joint Official Positions of the ISCD and IOF advising clinicians regarding FRAX® usage. As part of the process, the charge of the FRAX® International Task Force was to review and synthesize data regarding geographic and race/ethnic variability in hip fractures, non-hip osteoporotic fractures, and make recommendations about the use of FRAX® in ethnic groups and countries without a FRAX® calculator. This synthesis was presented to the expert panel and constitutes the data on which the subsequent Official Positions are predicated. A summary of the International Task Force composition and charge is presented here. Copyright © 2011 The International Society for Clinical Densitometry. Published by Elsevier Inc. All rights reserved.

  2. International Society of Sports Nutrition Position Stand: protein and exercise.

    Science.gov (United States)

    Jäger, Ralf; Kerksick, Chad M; Campbell, Bill I; Cribb, Paul J; Wells, Shawn D; Skwiat, Tim M; Purpura, Martin; Ziegenfuss, Tim N; Ferrando, Arny A; Arent, Shawn M; Smith-Ryan, Abbie E; Stout, Jeffrey R; Arciero, Paul J; Ormsbee, Michael J; Taylor, Lem W; Wilborn, Colin D; Kalman, Doug S; Kreider, Richard B; Willoughby, Darryn S; Hoffman, Jay R; Krzykowski, Jamie L; Antonio, Jose

    2017-01-01

    The International Society of Sports Nutrition (ISSN) provides an objective and critical review related to the intake of protein for healthy, exercising individuals. Based on the current available literature, the position of the Society is as follows:An acute exercise stimulus, particularly resistance exercise, and protein ingestion both stimulate muscle protein synthesis (MPS) and are synergistic when protein consumption occurs before or after resistance exercise.For building muscle mass and for maintaining muscle mass through a positive muscle protein balance, an overall daily protein intake in the range of 1.4-2.0 g protein/kg body weight/day (g/kg/d) is sufficient for most exercising individuals, a value that falls in line within the Acceptable Macronutrient Distribution Range published by the Institute of Medicine for protein.Higher protein intakes (2.3-3.1 g/kg/d) may be needed to maximize the retention of lean body mass in resistance-trained subjects during hypocaloric periods.There is novel evidence that suggests higher protein intakes (>3.0 g/kg/d) may have positive effects on body composition in resistance-trained individuals (i.e., promote loss of fat mass).Recommendations regarding the optimal protein intake per serving for athletes to maximize MPS are mixed and are dependent upon age and recent resistance exercise stimuli. General recommendations are 0.25 g of a high-quality protein per kg of body weight, or an absolute dose of 20-40 g.Acute protein doses should strive to contain 700-3000 mg of leucine and/or a higher relative leucine content, in addition to a balanced array of the essential amino acids (EAAs).These protein doses should ideally be evenly distributed, every 3-4 h, across the day.The optimal time period during which to ingest protein is likely a matter of individual tolerance, since benefits are derived from pre- or post-workout ingestion; however, the anabolic effect of exercise is long-lasting (at least 24 h), but likely

  3. International Volcanological Field School: Introduction to Geohazard Research and Monitoring

    Science.gov (United States)

    Izbekov, P. E.; Kravchunovskaya, E. A.; Eichelberger, J. C.; Gordeev, E.; Novik, Y. O.; Chebrov, V. N.

    2012-12-01

    The Kurile-Kamchatka-Aleutian- Alaska portion of the Pacific Rim of Fire spans nearly 5,400 km. It is home for more than 110 active volcanoes, which produce 4-6 significant explosive eruptions per year. It is also the source of some of the largest tsunami-generating earthquakes in the history of mankind. Volcanic ash clouds and tsunami waves generated in this area travel for thousands of kilometers defying political boundaries, thus making the international cooperation crucial for mitigating geohazards in the Northern Pacifica. In 2003, the University of Alaska Fairbanks, the Institute of Volcanology and Seismology, the Vitus Bering Kamchatka State University, with strong support from the Kamchatka Branch of the Geophysical Survey of the Russian Academy of Sciences, have established the International Volcanological Field School. This field camp serves as an introduction to volcanology and covers fundamental aspects of geohazard research and monitoring. Offered at both sides of the Russia-US border, the School attracts students from various disciplines and cultures, providing a direct access to the best examples of explosive volcanism at Katmai National Park in Alaska and at Mutnovsky & Gorely volcanoes in Kamchatka. It complements our efforts to build a strong geoscience community in the Northern Pacifica and serves as an important tool to attract brightest young scientists to geohazard research and monitoring.

  4. Comparisons of recovery, external and internal load by playing position and match outcome in professional soccer

    Directory of Open Access Journals (Sweden)

    Juan H.S. Conde

    2018-02-01

    Full Text Available Abstract AIMS To compare the internal and external load and the recovery by playing position and the match outcome (wins, losses or draws in professional soccer. METHODS 23 male professional soccer athletes from a team of the first division of the Brazilian Championship took part into the study (age 26.1 ± 3.8 years old, weight 77.5 ± 5.0 kg, height 177.6 ± 5.1 cm. During the games, athletes were monitored by GPS and the variables of external loads were taken. Additionally, the session rating of perceived exertion (session RPE and the perceived recovery scale (PRS were collected 30 minutes and 40h after the end of the matches, respectively. RESULTS The external load was greater on full-backs and defense midfielders (p 20 km/h, covering higher distances >20 km/h; these stimuli makes them to perceive less recovered than defenders, defense and attack midfielders (p<0.05. Moreover, the defenders are those who cover lower distances by the minute and the defense midfielders are those who present the lower Peak Velocity (p<0.05. There were no significant differences between GPS variables, internal load and recovery. In addition, it was found a correlation between the external and the internal load (r=0.66; p=0.001. CONCLUSIONS The GPS variables and the perceived recovery are influenced by the playing position, but not by the match outcome.

  5. What is New in Internal Dosimetry and Monitoring?

    Energy Technology Data Exchange (ETDEWEB)

    Henrichs, K. [Siemens AG, Corporate Radiation Safety and Dangerous Goods Transport, Munich (Germany); Nosske, D. [Federal Office for Radiation Protection, Neuherberg (Germany)

    2006-07-01

    This file is divided in two parts:the first one concerns the progress in internal dosimetry. This part gives an overview on new model developments by ICRP, the series of age dependent doses for members of the public was continued by biokinetic and dosimetric models for the embryo and foetus due to activity intake by the mother (ICRP,2001) and for the infant via consumption of mother's milk after activity intake by the mother (ICRP, 2004). In both publications dose coefficients for the embryo and foetus as well the infant were given for various intake scenarios by mother. The present model development work of ICRP is a revision of Publications 30, 54, 68, and 78 based on the new human Alimentary tract model (H.A.T.M.) of ICRP (ICRP, 2006), a revision of absorption parameters for the human respiratory tract model (ICRP, 1994a), new systemic models as well as new dosimetric parameters derived with new Voxel models for the reference male and female adult. The second part concerns the progress in workers monitoring for radionuclide intake. The initiatives to improve the situation are the guidelines published by the International Atomic Energy Agency (2004), giving guidance for the assessment of occupational exposures due to intakes of radionuclides, research project funded by the European Commission: the objective of O.M.I.N.E.X. was the improvement of monitoring programmes, taking into account the uncertainties of biokinetic models and data, the programme I.D.E.A. tried to improve measuring techniques and I.D.E.A.S derives rules for the evaluation of measured activity values in terms of exposure. Standardization projects by the International Standardization Organization I.S.O.: I.S.O. (2001) published a standard defining the requirements for bioassay laboratories, which will soon followed by a second part giving the rationale behind these rules., presently the final version (I.S.O. 2005) of a standard is circulating among the I.S.O. member states which guidance on

  6. What is New in Internal Dosimetry and Monitoring?

    International Nuclear Information System (INIS)

    Henrichs, K.; Nosske, D.

    2006-01-01

    This file is divided in two parts:the first one concerns the progress in internal dosimetry. This part gives an overview on new model developments by ICRP, the series of age dependent doses for members of the public was continued by biokinetic and dosimetric models for the embryo and foetus due to activity intake by the mother (ICRP,2001) and for the infant via consumption of mother's milk after activity intake by the mother (ICRP, 2004). In both publications dose coefficients for the embryo and foetus as well the infant were given for various intake scenarios by mother. The present model development work of ICRP is a revision of Publications 30, 54, 68, and 78 based on the new human Alimentary tract model (H.A.T.M.) of ICRP (ICRP, 2006), a revision of absorption parameters for the human respiratory tract model (ICRP, 1994a), new systemic models as well as new dosimetric parameters derived with new Voxel models for the reference male and female adult. The second part concerns the progress in workers monitoring for radionuclide intake. The initiatives to improve the situation are the guidelines published by the International Atomic Energy Agency (2004), giving guidance for the assessment of occupational exposures due to intakes of radionuclides, research project funded by the European Commission: the objective of O.M.I.N.E.X. was the improvement of monitoring programmes, taking into account the uncertainties of biokinetic models and data, the programme I.D.E.A. tried to improve measuring techniques and I.D.E.A.S derives rules for the evaluation of measured activity values in terms of exposure. Standardization projects by the International Standardization Organization I.S.O.: I.S.O. (2001) published a standard defining the requirements for bioassay laboratories, which will soon followed by a second part giving the rationale behind these rules., presently the final version (I.S.O. 2005) of a standard is circulating among the I.S.O. member states which guidance on the

  7. Beam Position Monitor and Energy Analysis at the Fermilab Accelerator Science and Technology Facility

    Energy Technology Data Exchange (ETDEWEB)

    Lopez, David Juarez [Univ. of Guanajuato (Mexico)

    2015-08-01

    Fermilab Accelerator Science and Technology Facility has produced its first beam with an energy of 20 MeV. This energy is obtained by the acceleration at the Electron Gun and the Capture Cavity 2 (CC2). When fully completed, the accelerator will consist of a photoinjector, one International Liner Collider (ILC)-type cryomodule, multiple accelerator R&D beamlines, and a downstream beamline to inject 300 MeV electrons into the Integrable Optics Test Accelerator (IOTA). We calculated the total energy of the beam and the corresponding energy to the Electron Gun and CC2. Subsequently, a Beam Position Monitors (BPM) error analysis was done, to calculate the device actual resolution.

  8. Participatory Patterns in an International Air Quality Monitoring Initiative.

    Science.gov (United States)

    Sîrbu, Alina; Becker, Martin; Caminiti, Saverio; De Baets, Bernard; Elen, Bart; Francis, Louise; Gravino, Pietro; Hotho, Andreas; Ingarra, Stefano; Loreto, Vittorio; Molino, Andrea; Mueller, Juergen; Peters, Jan; Ricchiuti, Ferdinando; Saracino, Fabio; Servedio, Vito D P; Stumme, Gerd; Theunis, Jan; Tria, Francesca; Van den Bossche, Joris

    2015-01-01

    The issue of sustainability is at the top of the political and societal agenda, being considered of extreme importance and urgency. Human individual action impacts the environment both locally (e.g., local air/water quality, noise disturbance) and globally (e.g., climate change, resource use). Urban environments represent a crucial example, with an increasing realization that the most effective way of producing a change is involving the citizens themselves in monitoring campaigns (a citizen science bottom-up approach). This is possible by developing novel technologies and IT infrastructures enabling large citizen participation. Here, in the wider framework of one of the first such projects, we show results from an international competition where citizens were involved in mobile air pollution monitoring using low cost sensing devices, combined with a web-based game to monitor perceived levels of pollution. Measures of shift in perceptions over the course of the campaign are provided, together with insights into participatory patterns emerging from this study. Interesting effects related to inertia and to direct involvement in measurement activities rather than indirect information exposure are also highlighted, indicating that direct involvement can enhance learning and environmental awareness. In the future, this could result in better adoption of policies towards decreasing pollution.

  9. Optimization of signal processing algorithm for digital beam position monitor

    International Nuclear Information System (INIS)

    Lai Longwei; Yi Xing; Leng Yongbin; Yan Yingbing; Chen Zhichu

    2013-01-01

    Based on turn-by-turn (TBT) signal processing, the paper emphasizes on the optimization of system timing and implementation of digital automatic gain control, slow application (SA) modules. Beam position including TBT, fast application (FA) and SA data can be acquired. On-line evaluation on Shanghai Synchrotron Radiation Facility (SSRF) shows that the processor is able to get the multi-rate position data which contain true beam movements. When the storage ring is 174 mA and 500 bunches filled, the resolutions of TBT data, FA data and SA data achieve 0.84, 0.44 and 0.23 μm respectively. The above results prove that the design could meet the performance requirements. (authors)

  10. Survey of special nuclear material vehicle monitors for domestic and international safeguards

    International Nuclear Information System (INIS)

    Fehlau, P.E.; Atwater, H.F.; Caldwell, J.T.; Shunk, E.R.

    1979-01-01

    Special nuclear materials vehicle monitors, including gateside vehicle monitors, hand-held personnel-vehicle monitors, and a new tunnel monitor concept for very large vehicles, are discussed. The results of a comparison of effectiveness of monitors for domestic application are presented. The results of calculations and small scale prototype measurements are given for a tunnel-like neutron monitor for monitoring at the perimeter of an enrichment plant subjected to International Safeguards

  11. The effect of thyroid autoantibody positivity on the functions of internal ear.

    Science.gov (United States)

    Gunes, Akif; Karakus, Mehmet Fatih; Telli, Tugba Akin; Gunes, Nurcan Akbas; Mutlu, Murad

    2017-11-01

    The objective of the study is to investigate if any significant difference exists in hearing thresholds and tympanometric examination results among patients whose thyroid antibody positivity was detected approximately 1 year or at least 5 years ago. Study population aged less than 40 years consisted of 17 patients who had thyroid antibody positivities for an average of 1 year (first group), 15 patients who were followed up for at least 5 years for thyroid antibody positivity (second group), and 18 volunteers (third group). Tympanometric examination results, stapes reflex, SRT, SD, and pure tone values were examined. When the second group and the third group were compared, significant results were obtained at hearing frequencies between 500 and 4000 Hz. When the first group and the third group were compared, only at 1000 Hz threshold significant results were obtained. During evaluation of hearing frequencies between 250 and 8000 Hz, significant results were not observed between the second group and the first group. When the first and the second groups were compared with the control group, significant results were obtained as for tympanometric examination findings and significant results were not observed between the second group and the first group. A significant difference was not detected as for the results of stapes reflex. Since thyroid antibody positivity affects the functions of internal ear, these patients should be more closely monitored. Since these effects become deeper in line with increased exposure to autoantibody positivity, variations in auditory responses should be more attentively monitored.

  12. Fault Monitoring and Fault Recovery Control for Position Moored Tanker

    DEFF Research Database (Denmark)

    Fang, Shaoji; Blanke, Mogens

    2011-01-01

    This paper addresses fault tolerant control for position mooring of a shuttle tanker operating in the North Sea. A complete framework for fault diagnosis is presented but the loss of a sub-sea mooring line buoyancy element is given particular attention, since this fault could lead to mooring line...... breakage and a high-risk abortion of an oil-loading operation. With significant drift forces from waves, non-Gaussian elements dominate forces and the residuals designed for fault diagnosis. Hypothesis testing need be designed using dedicated change detection for the type of distribution encountered....... Properties of detection and fault-tolerant control are demonstrated by high fidelity simulations....

  13. Monitoring beam position in the TRISTAN AR-to-MR transport lines

    International Nuclear Information System (INIS)

    Ieiri, Takao; Arinaga, Mitsuhiro

    1994-01-01

    A beam-position monitor (BPM) has been installed in the transport lines between the Accumulation Ring (AR) and the Main Ring (MR) of TRISTAN. This monitor can detect the beam position and its charge every passage of the beam. Variations of the beam position have been observed during the routine operation. An investigation into the AR extraction components has been carried out in order to clarify a source of the variations. (author)

  14. Monitoring External and Internal Loads of Brazilian Soccer Referees During Official Matches

    Science.gov (United States)

    Costa, Eduardo C.; Vieira, Caio M. A.; Moreira, Alexandre; Ugrinowitsch, Carlos; Castagna, Carlo; Aoki, Marcelo S.

    2013-01-01

    This study aimed to assess the external and internal loads of Brazilian soccer referees during official matches. A total of 11 field referees (aged 36.2 ± 7.5 years) were monitored during 35 matches. The external (distance covered, mean and maximal speed) and internal load parameters (session ratings of perceived exertion [RPE] training load [TL], Edwards' TL, and time spent in different heart rate [HR] zones) were assessed in 3-4 matches per referee. External load parameters were measured using a wrist Global Positioning System (GPS) receiver. No differences in distance covered (5.219 ± 205 vs. 5.230 ± 237 m) and maximal speed (19.3 ± 1.0 vs. 19.4 ± 1.4 km·h-1) were observed between the halves of the matches (p > 0.05). However, the mean speed was higher in the first half of the matches (6.6 ± 0.4 vs. 6.4 ± 0.3 km·h-1) (p < 0.05) than in the second half. The mean HR during the matches was ~89% of HRmax. In ~95% of the matches, the referees demonstrated a HR ≥ 80% of HRmax. Nonetheless, the time spent at 90-100% of HRmax was higher in the first half (59.9 vs. 52.3%) (p < 0.05). Significant correlations between session RPE TL and distance covered at 90-100% of HRmax (r = 0.62) and session RPE TL and maximal speed (r = 0.54) (p < 0.05) were noted. Furthermore, there was a positive correlation between session RPE TL and Edwards' TL (r = 0.61) (p < 0.05). Brazilian soccer referees demonstrated high external and internal load demands during official matches. The portable GPS/HR monitors and session RPE method can provide relevant information regarding the magnitude of the physiological strain during official matches. Key Points High external and internal loads were imposed on Brazilian soccer referees during official matches. There was a high positive correlation between a subjective marker of internal load (session RPE) and parameters of external load (distance covered between 90-100% of HRmax and maximal speed). There was a high positive correlation between

  15. International society of sports nutrition position stand: nutrient timing.

    Science.gov (United States)

    Kerksick, Chad M; Arent, Shawn; Schoenfeld, Brad J; Stout, Jeffrey R; Campbell, Bill; Wilborn, Colin D; Taylor, Lem; Kalman, Doug; Smith-Ryan, Abbie E; Kreider, Richard B; Willoughby, Darryn; Arciero, Paul J; VanDusseldorp, Trisha A; Ormsbee, Michael J; Wildman, Robert; Greenwood, Mike; Ziegenfuss, Tim N; Aragon, Alan A; Antonio, Jose

    2017-01-01

    The International Society of Sports Nutrition (ISSN) provides an objective and critical review regarding the timing of macronutrients in reference to healthy, exercising adults and in particular highly trained individuals on exercise performance and body composition. The following points summarize the position of the ISSN:Nutrient timing incorporates the use of methodical planning and eating of whole foods, fortified foods and dietary supplements. The timing of energy intake and the ratio of certain ingested macronutrients may enhance recovery and tissue repair, augment muscle protein synthesis (MPS), and improve mood states following high-volume or intense exercise.Endogenous glycogen stores are maximized by following a high-carbohydrate diet (8-12 g of carbohydrate/kg/day [g/kg/day]); moreover, these stores are depleted most by high volume exercise.If rapid restoration of glycogen is required ( 70) glycemic indexthe addition of caffeine (3-8 mg/kg)combining carbohydrates (0.8 g/kg/h) with protein (0.2-0.4 g/kg/h) Extended (> 60 min) bouts of high intensity (> 70% VO 2 max) exercise challenge fuel supply and fluid regulation, thus carbohydrate should be consumed at a rate of ~30-60 g of carbohydrate/h in a 6-8% carbohydrate-electrolyte solution (6-12 fluid ounces) every 10-15 min throughout the entire exercise bout, particularly in those exercise bouts that span beyond 70 min. When carbohydrate delivery is inadequate, adding protein may help increase performance, ameliorate muscle damage, promote euglycemia and facilitate glycogen re-synthesis.Carbohydrate ingestion throughout resistance exercise (e.g., 3-6 sets of 8-12 repetition maximum [RM] using multiple exercises targeting all major muscle groups) has been shown to promote euglycemia and higher glycogen stores. Consuming carbohydrate solely or in combination with protein during resistance exercise increases muscle glycogen stores, ameliorates muscle damage, and facilitates greater acute and

  16. Biosecurity and Health Monitoring at the Zebrafish International Resource Center.

    Science.gov (United States)

    Murray, Katrina N; Varga, Zoltán M; Kent, Michael L

    2016-07-01

    The Zebrafish International Resource Center (ZIRC) is a repository and distribution center for mutant, transgenic, and wild-type zebrafish. In recent years annual imports of new zebrafish lines to ZIRC have increased tremendously. In addition, after 15 years of research, we have identified some of the most virulent pathogens affecting zebrafish that should be avoided in large production facilities, such as ZIRC. Therefore, while importing a high volume of new lines we prioritize safeguarding the health of our in-house fish colony. Here, we describe the biosecurity and health-monitoring program implemented at ZIRC. This strategy was designed to prevent introduction of new zebrafish pathogens, minimize pathogens already present in the facility, and ensure a healthy zebrafish colony for in-house uses and shipment to customers.

  17. Requirements for internal contamination monitoring units; Anforderungen an Inkorporationsmessstellen

    Energy Technology Data Exchange (ETDEWEB)

    Werner, E. [GSF, Inst. fuer Biophysikalische Strahlenforschung, Frankfurt am Main (Germany); Beyer, D. [Forschungszentrum Juelich, Abt. ASS (Germany); Doerfel, H. [Hauptabteilung Sicherheit, Kernforschungszentrum Karlsruhe (Germany); Erlenbach, H. [Zentralstelle fuer Sicherheitstechnik NRW, Duesseldorf (Germany); Fischbach, G. [Siemens Brennelementewerk, Hanau (Germany); Henrichs, K. [Siemens AG, Muenchen (Germany); Keller, K.D. [Radiologische Universitaetsklinik, Tuebingen (Germany); Koenig, K. [Bundesamt fuer Strahlenschutz, ISH, Neuherberg (Germany); Riedel, W. [Freie Univ. Berlin, Klinikum Steglitz (Germany); Scheler, R. [Bundesamt fuer Strahlenschutz, FB Strahlenschutz, Berlin (Germany); Schieferdecker, H. [Hauptabteilung Sicherheit, Kernforschungszentrum Karlsruhe (Germany)

    1994-12-31

    For the evaluation of internal contamination by officially authorized monitoring units according to section 63 (6) of the German radiation protection ordinance, a directive will be prepared in order to define uniform requirements for the laboratories in charge of incorporation monitoring by appointment of the relevant authorities. These requirements refer to equipment, to performance of measurements, to interpretation of measured values, to quality control as well as to documentation and to delivery of results. The duties of such laboratories comprise measurements of radioactivity, evaluation of intakes of radionuclides and of the resulting internal radiation dose, but also transmission of results to the employer, to the central dose registry, and under certain circumstances to the authorities. Among the requirements to be met by the laboratory for incorporation control are a sufficient measuring efficiency, the implementation of in-house checks, and the participation in intercomparison programs. For the accomplishment of such duties the laboratory needs appropriate apparatus, rooms, facilities, and staffing. (orig.) [Deutsch] Zur Ermittlung der Koerperdosen nach Paragraph 63 StrlSchV sind fuer die gemaess Abs. 6 von der zustaendigen Behoerde zu bestimmenden Messstellen in einer Richtlinie einheitliche Anforderungen festzulegen. Diese beziehen sich auf deren Ausstattung, die Durchfuehrung der Messungen, Auswertungen und Qualitaetskontrollen sowie die Aufzeichnung und Uebermittlung der Ergebnisse. Die Aufgaben der Messstellen umfassen die Messungen der Radioaktivitaet im Koerper bzw. in Koerperausscheidungen, die Ermittlung der Zufuhr an Radionukliden sowie der daraus resultierenden Koerperdosis und die Weiterleitung der Ergebnisse an den Auftraggeber, an das zentrale Dosisregister und in bestimmten Faellen an die Behoerde. Zu den von einer Messstelle zu erfuellenden Anforderungen gehoeren eine ausreichende Messeffektivitaet, die Durchfuehrung von Eigenkontrollen

  18. Activation monitoring accuracy in experiments on internal targets

    International Nuclear Information System (INIS)

    Barabash, L.Z.; Buklej, A.E.; Gavrilov, V.B.

    1975-01-01

    Experiments showed that by using combined targets, comprising a monitor aluminium foil and the substance examined, in the internal beam of a proton synchrotron, one can determine the number of particles that had passed through the target by the induced activity of 24 Na in aluminium. A combined target consisting of three aluminium foils (2.3 m.g./sq.cm) and a foil of the test substance (30-170 mg/sq.cm) was used. Monitoring was performed by the activity of the middle aluminium foil. Subsequent to respective measurements, the foils were extracted from the accelerator chamber and aged for 12-16 hr to cause decay of short-lived activities. The foil γ-ray spectrum was then recorded by means of a coaxial Ge-Li detector (40 cc, 8 keV). Results of control measurements were cited. The method ensured relatively accurate measurements (ca. 2%) of the dependence of cross-sections of the atomic number of the target nucleus

  19. International society of sports nutrition position stand: caffeine and performance

    OpenAIRE

    Goldstein, Erica R; Ziegenfuss, Tim; Kalman, Doug; Kreider, Richard; Campbell, Bill; Wilborn, Colin; Taylor, Lem; Willoughby, Darryn; Stout, Jeff; Graves, B Sue; Wildman, Robert; Ivy, John L; Spano, Marie; Smith, Abbie E; Antonio, Jose

    2010-01-01

    Abstract Position Statement: The position of The Society regarding caffeine supplementation and sport performance is summarized by the following seven points: 1.) Caffeine is effective for enhancing sport performance in trained athletes when consumed in low-to-moderate dosages (~3-6 mg/kg) and overall does not result in further enhancement in performance when consumed in higher dosages (≥ 9 mg/kg). 2.) Caffeine exerts a greater ergogenic effect when consumed in an anhydrous state as compared ...

  20. Standardized monitoring of Rangifer health during International Polar Year

    Directory of Open Access Journals (Sweden)

    Susan Kutz

    2013-06-01

    Full Text Available Normal 0 21 false false false SV X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Normal tabell"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin-top:0cm; mso-para-margin-right:0cm; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0cm; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-fareast-language:EN-US;} Monitoring of individual animal health indices in wildlife populations can be a powerful tool for evaluation of population health, detecting changes, and informing management decisions. Standardized monitoring allows robust comparisons within and across populations, and over time and vast geographic regions. As an International Polar Year Initiative, the CircumArctic Rangifer Monitoring and Assessment network established field protocols for standardized monitoring of caribou and reindeer (Rangifer tarandus health, which included body condition, contaminants, and pathogen exposure and abundance. To facilitate use of the protocols, training sessions were held, additional resources were developed, and language was translated where needed. From March 2007 to September 2010, at least 1206 animals from 16 circumpolar herds were sampled in the field using the protocols. Four main levels of sampling were done and ranged from basic to comprehensive sampling. Possible sources of sampling error were noted by network members early in the process and protocols were modified or supplemented with additional visual resources to improve clarity when needed. This is the first time that such broad and comprehensive circumpolar sampling of migratory caribou and wild reindeer, using standardized protocols covering both body

  1. Harmonisation (legal, dosimetric, quality aspects) of individual monitoring, and integration of monitoring for external and internal exposures (EURADOS working group)

    International Nuclear Information System (INIS)

    Lopez, M.A.; Currivan, L.; Falk, R.; Olko, P.; Wernli, C.; Castellani, C.M.; Dijk, J.W.E. van

    2003-01-01

    The EURADOS Working Group II on 'Harmonisation of individual monitoring' consists of experts from almost all EU Member States and Newly Associated States (NAS), involved in tasks related to the assessment of doses for internal and external radiation. The final objective is to achieve harmonisation in individual monitoring for occupational exposures. Sub-group 2 activities are focused on investigating how the results from personal dosemeters for external radiation and workplace monitoring and from monitoring for internal exposure can be combined into a complete and consistent system of individual monitoring. Three questionnaires were prepared, covering Individual monitoring of external radiation (Questionnaire 1), 'Internal exposure' (Questionnaire 2) and 'Natural sources of radiation at workplace' (Questionnaire 3). With the agreement of a 'contact-person' selected in each country, the distribution of the three EURADOS 2002 questionnaires was carried out by e-mail among the dosimetry facilities of 28 European countries. The preliminary results of these actions are presented here. (author)

  2. Survey of international dose monitoring programmes for radiation workers. WP1 in the project OMINEX- (Optimisation of Monitoring for Internal Exposure)

    International Nuclear Information System (INIS)

    Rahola, T.; Muikku, M.; Pusa, S.; Etherington, G.; Berard, P.; Guen, B. Le; Hurtgen, C.

    2004-05-01

    Monitoring of the workforce in the nuclear industries is carried out primarily in order to demonstrate compliance with European Union Basic Safety Standards for the protection of the health of workers against the dangers arising from ionizing radiation. There is however no compilation of information on internal dose monitoring programmes currently in use in the EU countries. Surveys were therefore carried out in which organisations were asked to provide information on the design of their internal dose monitoring programmes and on the costs of these programmes. Information was requested from both EU countries and Associated States. Databases for storage and reporting of all information gained were constructed, and results from the surveys compiled. This work was carried out within the EC 5th Framework Programme project OMINEX (Optimisation of Monitoring for Internal Exposure), which aims to provide advice and guidance on designing and implementing internal dose monitoring programmes in the workplace in such a way that best use is made of available resources, while minimising costs. This paper gives the results of the survey of the design of internal dose monitoring programmes. A major conclusion is that, particularly for the actinides, a wide range of approaches to monitoring are in use. There is no consensus on primary monitoring methods. All organisations monitor workers to assess individual doses for entry onto a legal dose record. Cumulative distributions show that most organisations aim to assess doses down to 0.1 - 0.5 mSv. (orig.)

  3. International Social Medicine between the Wars : Positioning a Volatile Concept

    Directory of Open Access Journals (Sweden)

    Borowy, Iris

    2007-12-01

    Full Text Available International health work during the 1930s was influenced by several inter-acting developments which caused general attention to turn away from pathogens and individual diseases to social conditions and their impact on the status of public health. Internationally, the League of Nations Health Organisation became the centre of initiatives in social medicine. After 1932, the search for the health implications of the depression invigorated ongoing social studies. Thus, nutrition, housing and rural hygiene became major issues, followed by discussions on sports. All these topics had important political connotations because they touched sensitive questions of welfare, status and the distribution of wealth and poverty within societies. In the process, they opened discussions on abstract issues like social and moral justice and on tangible questions of political systems.

  4. A review on bridge dynamic displacement monitoring using global positioning system and accelerometer

    Science.gov (United States)

    Yunus, Mohd Zulkifli Mohd; Ibrahim, Nuremira; Ahmad, Fatimah Shafinaz

    2018-02-01

    This paper reviews previous research on bridge dynamic displacement monitoring using Global Positioning System (GPS) and an accelerometer for Structural Health Monitoring (SHM) of bridge. These include the review of the advantages and disadvantages of the measurement as well as the methodology of the measurements used in the recent research study. This review could provide a preliminary decision overview for students or researchers before initiating a research related to the bridge dynamic displacement monitoring.

  5. The APS X-ray undulator photon beam position monitor and tests at CHESS and NSLS

    International Nuclear Information System (INIS)

    Shu, D.; Rodricks, B.; Barraza, J.; Sanchez, T.; Kuzay, T.M.

    1992-01-01

    The advent of thirs generation synchrotron sources, like the Advanced Photon Source (APS), will provide significant increases in brilliance over existing synchrotron sources. The APS X-ray undulators will increase the brilliance in the 3-40 keV range by several orders of magnitude. Thus, the design of the photon beam position monitor is a challenging engineering task. The beam position monitors must withstand the high thermal load, be able to achieve submicron spatial resolution while maintaining their stability, and be compatible with both undulators and wigglers. A preliminary APS prototype photon beam position monitor consisting of a CVD-diamond-based, tungsten-coated blade was tested on the APS/CHESS undulator at the Cornell High Energy Synchrotron Radiation Source (CHESS) and on the NSLS X-13 undulator beamline. Results from these tests, as well as the design of this prototype APS photon beam position monitor, will be discussed in this paper. (orig.)

  6. Life Support and Environmental Monitoring International System Maturation Team Considerations

    Science.gov (United States)

    Anderson, Molly; Gatens, Robyn; Ikeda, Toshitami; Ito, Tsuyoshi; Hovland, Scott; Witt, Johannes

    2016-01-01

    Human exploration of the solar system is an ambitious goal. Future human missions to Mars or other planets will require the cooperation of many nations to be feasible. Exploration goals and concepts have been gathered by the International Space Exploration Coordination Group (ISECG) at a very high level, representing the overall goals and strategies of each participating space agency. The Global Exploration Roadmap published by ISECG states that international partnerships are part of what drives the mission scenarios. It states "Collaborations will be established at all levels (missions, capabilities, technologies), with various levels of interdependency among the partners." To make missions with interdependency successful, technologists and system experts need to share information early, before agencies have made concrete plans and binding agreements. This paper provides an overview of possible ways of integrating NASA, ESA, and JAXA work into a conceptual roadmap of life support and environmental monitoring capabilities for future exploration missions. Agencies may have immediate plans as well as long term goals or new ideas that are not part of official policy. But relationships between plans and capabilities may influence the strategies for the best ways to achieve partner goals. Without commitments and an organized program like the International Space Station, requirements for future missions are unclear. Experience from ISS has shown that standards and an early understanding of requirements are an important part of international partnerships. Attempting to integrate systems that were not designed together can create many problems. Several areas have been identified that could be important to discuss and understand early: units of measure, cabin CO2 levels, and the definition and description of fluids like high purity oxygen, potable water and residual biocide, and crew urine and urine pretreat. Each of the partners is exploring different kinds of technologies

  7. Performance of photon position monitors and stability of undulator beams at the Advanced Light Source

    International Nuclear Information System (INIS)

    Warwick, T.; Andresen, N.; Portmann, G.; Jackson, A.

    1994-01-01

    Position monitors are implemented in three undulator beamlines at the ALS. Their performance has been studied carefully on one of these lines and is reviewed. The monitors work as expected and show the ALS to be an exceptionally stable source of synchrotron radiation

  8. Causes and consequences of timing errors associated with global positioning system collar accelerometer activity monitors

    Science.gov (United States)

    Adam J. Gaylord; Dana M. Sanchez

    2014-01-01

    Direct behavioral observations of multiple free-ranging animals over long periods of time and large geographic areas is prohibitively difficult. However, recent improvements in technology, such as Global Positioning System (GPS) collars equipped with motion-sensitive activity monitors, create the potential to remotely monitor animal behavior. Accelerometer-equipped...

  9. PerPos: a Translucent Positioning Middleware Supporting Adaptation of Internal Positioning Processes

    DEFF Research Database (Denmark)

    Jensen, Jakob Langdal; Schougaard, Kari Rye; Kjærgaard, Mikkel Baun

    2010-01-01

    process. To address this problem this paper proposes a positioning middleware named PerPos that is translucent and adaptable, i.e., it supports both high- and low-level interaction. The PerPos middleware provides translucency with respect to the positioning process and allows programmatic definition...

  10. International Professional Positions - Adjusting to the Japanese Culture

    Science.gov (United States)

    Friend, Megan

    2015-04-01

    Starting a new professional position in a foreign country offers some exciting and wonderful new prospects, as well as many challenging ones. Unique experiences, the opportunity to learn about and become intimately familiar with a new culture, the chance to learn a new language, and, of course, the opportunity to pursue research opportunities not available in the US, are all positive aspects of deciding to join a foreign research institute. Adjusting to a new culture, and particularly a new workplace culture, can be very difficult, however. I will relay my experiences as a postdoc, and then an assistant professor, at one of the leading research institutes in Japan. Having lived and worked there for over two and a half years, I have discovered both the positive (ramen and ``onsen'' - outdoor public bath) and negative (``karoushi'' - death from overwork) sides of this major life decision. I hope to answer questions prospective foreign researchers may have about the difficult and very rewarding prospect of joining a foreign research institute.

  11. International Society of Sports Nutrition position stand: meal frequency

    Directory of Open Access Journals (Sweden)

    Stout Jeffrey R

    2011-03-01

    Full Text Available Abstract Position Statement: Admittedly, research to date examining the physiological effects of meal frequency in humans is somewhat limited. More specifically, data that has specifically examined the impact of meal frequency on body composition, training adaptations, and performance in physically active individuals and athletes is scant. Until more research is available in the physically active and athletic populations, definitive conclusions cannot be made. However, within the confines of the current scientific literature, we assert that: 1. Increasing meal frequency does not appear to favorably change body composition in sedentary populations. 2. If protein levels are adequate, increasing meal frequency during periods of hypoenergetic dieting may preserve lean body mass in athletic populations. 3. Increased meal frequency appears to have a positive effect on various blood markers of health, particularly LDL cholesterol, total cholesterol, and insulin. 4. Increased meal frequency does not appear to significantly enhance diet induced thermogenesis, total energy expenditure or resting metabolic rate. 5. Increasing meal frequency appears to help decrease hunger and improve appetite control. The following literature review has been prepared by the authors in support of the aforementioned position statement.

  12. ITRAP - an international pilot study on border monitoring systems

    International Nuclear Information System (INIS)

    Beck, P.; Duftschmid, K.E.

    1999-01-01

    The paper describes the design and preliminary results of an extended pilot study of commercially available monitoring systems for the detection of nuclear and other radioactive materials at borders. The study consists of a laboratory test phase and field tests at the Austrian/Hungarian border and the Vienna airport, each for a duration of one year. The results will be used to derive realistic performance requirements for border control systems in view of optimized technical and economic conditions as well as to propose an 'investigation level'. The ITRAP study consists of three phases. In the first phase equipment currently available on the market is subjected to laboratory testing at the Austrian Research Centres Seibersdorf. The instrument categories include hand-held, portable, and fixed-installed equipment. The test criteria defined as minimum requirements have been established together with the manufacturers. The laboratory tests started in May 1998 and will last until end of this year. During the second phase, the field study, equipment passing the laboratory tests will be installed at a major Austrian-Hungarian border crossing (Nickelsdorf) for monitoring of cars, trucks and trains, as well as at the Vienna airport for pedestrians, luggage and cargo. In this phase the results gained from the lab tests about the 'fitness for use' will be verified in practice, in close co-operation with the law enforcement officers at the borders. Also training issues and questions of maintenance and support shall be evaluated. In the third phase, realistic specifications and performance requirements shall be derived with the help of international experts and selected specialists from the users and manufacturers. The results of the field study will focus not only on the technical aspects of monitoring equipment (e.g. detection threshold and rate of false alarms) but also on the operational (e.g. ease of use, reliability, training requirements, field support) and economic

  13. Analytical expression for position sensitivity of linear response beam position monitor having inter-electrode cross talk

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, Mukesh, E-mail: mukeshk@rrcat.gov.in [Beam Diagnostics Section, Indus Operations, Beam Dynamics & Diagnostics Division, Raja Ramanna Centre for Advanced Technology, Indore, 452013 MP (India); Homi Bhabha National Institute, Training School Complex, Anushakti Nagar, Mumbai 400 094 (India); Ojha, A.; Garg, A.D.; Puntambekar, T.A. [Beam Diagnostics Section, Indus Operations, Beam Dynamics & Diagnostics Division, Raja Ramanna Centre for Advanced Technology, Indore, 452013 MP (India); Senecha, V.K. [Homi Bhabha National Institute, Training School Complex, Anushakti Nagar, Mumbai 400 094 (India); Ion Source Lab., Proton Linac & Superconducting Cavities Division, Raja Ramanna Centre for Advanced Technology, Indore, 452013 MP (India)

    2017-02-01

    According to the quasi electrostatic model of linear response capacitive beam position monitor (BPM), the position sensitivity of the device depends only on the aperture of the device and it is independent of processing frequency and load impedance. In practice, however, due to the inter-electrode capacitive coupling (cross talk), the actual position sensitivity of the device decreases with increasing frequency and load impedance. We have taken into account the inter-electrode capacitance to derive and propose a new analytical expression for the position sensitivity as a function of frequency and load impedance. The sensitivity of a linear response shoe-box type BPM has been obtained through simulation using CST Studio Suite to verify and confirm the validity of the new analytical equation. Good agreement between the simulation results and the new analytical expression suggest that this method can be exploited for proper designing of BPM.

  14. International society of sports nutrition position stand: caffeine and performance.

    Science.gov (United States)

    Goldstein, Erica R; Ziegenfuss, Tim; Kalman, Doug; Kreider, Richard; Campbell, Bill; Wilborn, Colin; Taylor, Lem; Willoughby, Darryn; Stout, Jeff; Graves, B Sue; Wildman, Robert; Ivy, John L; Spano, Marie; Smith, Abbie E; Antonio, Jose

    2010-01-27

    Position Statement: The position of The Society regarding caffeine supplementation and sport performance is summarized by the following seven points: 1.) Caffeine is effective for enhancing sport performance in trained athletes when consumed in low-to-moderate dosages (~3-6 mg/kg) and overall does not result in further enhancement in performance when consumed in higher dosages (>/= 9 mg/kg). 2.) Caffeine exerts a greater ergogenic effect when consumed in an anhydrous state as compared to coffee. 3.) It has been shown that caffeine can enhance vigilance during bouts of extended exhaustive exercise, as well as periods of sustained sleep deprivation. 4.) Caffeine is ergogenic for sustained maximal endurance exercise, and has been shown to be highly effective for time-trial performance. 5.) Caffeine supplementation is beneficial for high-intensity exercise, including team sports such as soccer and rugby, both of which are categorized by intermittent activity within a period of prolonged duration. 6.) The literature is equivocal when considering the effects of caffeine supplementation on strength-power performance, and additional research in this area is warranted. 7.) The scientific literature does not support caffeine-induced diuresis during exercise, or any harmful change in fluid balance that would negatively affect performance.

  15. International society of sports nutrition position stand: caffeine and performance

    Directory of Open Access Journals (Sweden)

    Wildman Robert

    2010-01-01

    Full Text Available Abstract Position Statement: The position of The Society regarding caffeine supplementation and sport performance is summarized by the following seven points: 1. Caffeine is effective for enhancing sport performance in trained athletes when consumed in low-to-moderate dosages (~3-6 mg/kg and overall does not result in further enhancement in performance when consumed in higher dosages (≥ 9 mg/kg. 2. Caffeine exerts a greater ergogenic effect when consumed in an anhydrous state as compared to coffee. 3. It has been shown that caffeine can enhance vigilance during bouts of extended exhaustive exercise, as well as periods of sustained sleep deprivation. 4. Caffeine is ergogenic for sustained maximal endurance exercise, and has been shown to be highly effective for time-trial performance. 5. Caffeine supplementation is beneficial for high-intensity exercise, including team sports such as soccer and rugby, both of which are categorized by intermittent activity within a period of prolonged duration. 6. The literature is equivocal when considering the effects of caffeine supplementation on strength-power performance, and additional research in this area is warranted. 7. The scientific literature does not support caffeine-induced diuresis during exercise, or any harmful change in fluid balance that would negatively affect performance.

  16. International Society of Sports Nutrition position stand: protein and exercise

    Directory of Open Access Journals (Sweden)

    Landis Jamie

    2007-09-01

    Full Text Available Abstract Position Statement The following seven points related to the intake of protein for healthy, exercising individuals constitute the position stand of the Society. They have been approved by the Research Committee of the Society. 1 Vast research supports the contention that individuals engaged in regular exercise training require more dietary protein than sedentary individuals. 2 Protein intakes of 1.4 – 2.0 g/kg/day for physically active individuals is not only safe, but may improve the training adaptations to exercise training. 3 When part of a balanced, nutrient-dense diet, protein intakes at this level are not detrimental to kidney function or bone metabolism in healthy, active persons. 4 While it is possible for physically active individuals to obtain their daily protein requirements through a varied, regular diet, supplemental protein in various forms are a practical way of ensuring adequate and quality protein intake for athletes. 5 Different types and quality of protein can affect amino acid bioavailability following protein supplementation. The superiority of one protein type over another in terms of optimizing recovery and/or training adaptations remains to be convincingly demonstrated. 6 Appropriately timed protein intake is an important component of an overall exercise training program, essential for proper recovery, immune function, and the growth and maintenance of lean body mass. 7 Under certain circumstances, specific amino acid supplements, such as branched-chain amino acids (BCAA's, may improve exercise performance and recovery from exercise.

  17. Internal monitoring of GBTx emulator using IPbus for CBM experiment

    Science.gov (United States)

    Mandal, Swagata; Zabolotny, Wojciech; Sau, Suman; Chkrabarti, Amlan; Saini, Jogender; Chattopadhyay, Subhasis; Pal, Sushanta Kumar

    2015-09-01

    The Compressed Baryonic Matter (CBM) experiment is a part of the Facility for Antiproton and Ion Research (FAIR) in Darmstadt at GSI. In CBM experiment a precisely time synchronized fault tolerant self-triggered electronics is required for Data Acquisition (DAQ) system in CBM experiments which can support high data rate (up to several TB/s). As a part of the implementation of the DAQ system of Muon Chamber (MUCH) which is one of the important detectors in CBM experiment, a FPGA based Gigabit Transceiver (GBTx) emulator is implemented. Readout chain for MUCH consists of XYTER chips (Front end electronics) which will be directly connected to detector, GBTx emulator, Data Processing Board (DPB) and First level event selector board (FLIB) with backend software interface. GBTx emulator will be connected with the XYTER emulator through LVDS (Low Voltage Differential Signalling) line in the front end and in the back end it is connected with DPB through 4.8 Gbps optical link. IPBus over Ethernet is used for internal monitoring of the registers within the GBTx. In IPbus implementation User Datagram Protocol (UDP) stack is used in transport layer of OSI model so that GBTx can be controlled remotely. A Python script is used at computer side to drive IPbus controller.

  18. Selective international migration by social position, health behaviour and personality.

    Science.gov (United States)

    Silventoinen, Karri; Hammar, Niklas; Hedlund, Ebba; Koskenvuo, Markku; Rönnemaa, Tapani; Kaprio, Jaakko

    2008-04-01

    Immigrants is an important minority in many countries, but little is known how they are self-selected. We analysed differences in psycho-social and health behavioural factors between international migrants and non-migrants prior to migration in a large cohort of Finnish twins. A questionnaire was sent to Finnish twins in 1975 (response rate 89%, N = 26555 twin individuals). Follow-up data on migration and mortality were derived from population registries in Finland and Sweden up to 31 March 2002. In 1998, another questionnaire was sent to Finnish twins migrated to Sweden and their co-twins (response rate 71%, N = 1534 twin individuals). The data were analysed using Cox and conditional logistic regression models. Life dissatisfaction, higher alcohol use and smoking at baseline predicted future migration. In men additionally, unemployment, neuroticism and extroversion increased the probability to migrate. Similar associations were found for alcohol use in men and smoking in men and women within twin pairs discordant for migration. Twins also reported retrospectively that prior to migration the migrated twin had been less satisfied with his/her educational institution or job and was generally less satisfied with life, used more alcohol (men) and smoked more (women) than the co-twin stayed in Finland. Migrants are self-selected by health behavioural and personality factors, which may compromise their health. The special requirements of migrants should be recognized in health care.

  19. Design and characterization of a prototype stripline beam position monitor for the Clic Drive Beam*

    CERN Document Server

    Benot-Morell, A; Wendt, M; Nappa, J M; Tassan-Viol, J; Vilalte, S; Smith, S

    2012-01-01

    The prototype of a stripline Beam Position Monitor (BPM) with its associated readout electronics is under development at CERN, in collaboration with SLAC, LAPP and IFIC. The anticipated position resolution and accuracy are expected to be below 2μm and 20μm respectively for operation of the BPM in the CLIC drive beam (DB) linac. This paper describes the particular CLIC DB conditions with respect to the beam position monitoring, presents the measurement concept, and summarizes electromagnetic simulations and RF measurements performed on the prototype.

  20. International Society of Sports Nutrition position stand: Nutrient timing

    Directory of Open Access Journals (Sweden)

    Ziegenfuss Tim

    2008-10-01

    Full Text Available Abstract Position Statement: The position of the Society regarding nutrient timing and the intake of carbohydrates, proteins, and fats in reference to healthy, exercising individuals is summarized by the following eight points: 1. Maximal endogenous glycogen stores are best promoted by following a high-glycemic, high-carbohydrate (CHO diet (600 – 1000 grams CHO or ~8 – 10 g CHO/kg/d, and ingestion of free amino acids and protein (PRO alone or in combination with CHO before resistance exercise can maximally stimulate protein synthesis. 2. During exercise, CHO should be consumed at a rate of 30 – 60 grams of CHO/hour in a 6 – 8% CHO solution (8 – 16 fluid ounces every 10 – 15 minutes. Adding PRO to create a CHO:PRO ratio of 3 – 4:1 may increase endurance performance and maximally promotes glycogen re-synthesis during acute and subsequent bouts of endurance exercise. 3. Ingesting CHO alone or in combination with PRO during resistance exercise increases muscle glycogen, offsets muscle damage, and facilitates greater training adaptations after either acute or prolonged periods of supplementation with resistance training. 4. Post-exercise (within 30 minutes consumption of CHO at high dosages (8 – 10 g CHO/kg/day have been shown to stimulate muscle glycogen re-synthesis, while adding PRO (0.2 g – 0.5 g PRO/kg/day to CHO at a ratio of 3 – 4:1 (CHO: PRO may further enhance glycogen re-synthesis. 5. Post-exercise ingestion (immediately to 3 h post of amino acids, primarily essential amino acids, has been shown to stimulate robust increases in muscle protein synthesis, while the addition of CHO may stimulate even greater levels of protein synthesis. Additionally, pre-exercise consumption of a CHO + PRO supplement may result in peak levels of protein synthesis. 6. During consistent, prolonged resistance training, post-exercise consumption of varying doses of CHO + PRO supplements in varying dosages have been shown to stimulate

  1. Internal exposure in nuclear medicine: application of IAEA criteria to determine the need for internal monitoring

    Directory of Open Access Journals (Sweden)

    Bernardo Maranhão Dantas

    2008-12-01

    Full Text Available The manipulation of unsealed sources in nuclear medicine poses significant risks of internal exposure to the staff. According to the International Atomic Energy Agency, the radiological protection program should include an evaluation of such risks and an individual monitoring plan, assuring acceptable radiological safety conditions in the workplace. The IAEA Safety Guide RS-G-1.2 recommends that occupational monitoring should be implemented whenever it is likely that committed effective doses from annual intakes of radionuclides would exceed 1 mSv. It also suggests a mathematical criterion to determine the need to implement internal monitoring. This paper presents a simulation of the IAEA criteria applied to commonly used radionuclides in nuclear medicine, taking into consideration usual manipulated activities and handling conditions. It is concluded that the manipulation of 131I for therapy presents the higher risk of internal exposure to the workers, requiring the implementation of an internal monitoring program by the Nuclear Medicine Centers.A manipulação de fontes abertas em Serviços de Medicina Nuclear envolve riscos de exposição externa e contaminação interna. O plano de proteção radiológica das Instalações licenciadas pela CNEN deve incluir a avaliação de tais riscos e propor um programa de monitoração individual de forma a controlar as exposições e garantir a manutenção das condições de segurança radiológica. As recomendações da AIEA apresentadas no Safety Guide RS-G-1.2 sugerem que seja implementado um programa de monitoração interna do trabalhador sempre que houver possibilidade da contaminação interna conduzir a valores de dose efetiva comprometida anual igual ou superior a 1 mSv. Este trabalho apresenta a simulação da aplicação de tais critérios para os radionuclídeos mais utilizados na área de Medicina Nuclear, levando-se em consideração as condições usuais de manipulação das fontes e as

  2. Mechanical valves in the pulmonary position: An international retrospective analysis.

    Science.gov (United States)

    Pragt, Hanna; van Melle, Joost P; Javadikasgari, Hoda; Seo, Dong Man; Stulak, John M; Knez, Igor; Hörer, Jürgen; Muñoz-Guijosa, Christian; Dehaki, Mahyar G; Shin, Hong Ju; Dearani, Joseph A; Dehaki, Maziar G; Pieper, Petronella G; Eulenburg, Christine; Dos, Laura; Ebels, Tjark

    2017-10-01

    Life expectancy of patients with congenital heart disease has improved over the past decades, increasing the need for a durable pulmonary prosthetic valve. Biological valves in various forms have become the valve of choice for pulmonary valve replacement (PVR), but structural valve deterioration is unavoidable in the long term. Use of a mechanical valve could be an alternative, but data on long-term outcomes are sparse. We retrospectively collected and analyzed data on 364 patients with mechanical valves implanted in the pulmonary position between 1965 and 2014. The data originate from medical centers in Barcelona (Spain), Graz (Austria), Groningen (the Netherlands), Munich (Germany), Rochester (United States), Seoul (Republic of Korea), and Tehran (Iran). Median follow-up duration was 4.26 years (range, 0-27 years), mean age at implantation was 27.16 ± 12.2 years. Tetralogy of Fallot was the most common primary cardiac diagnosis, with a subgroup of 69.8%. Freedom from valvular thrombosis was 91% (95% confidence interval [CI], 87%-94%) at 5 years and 86% (95% CI, 81%-91%) at 10 years post-PVR. With a success rate up to 88%, thrombolysis was a successful therapy. Freedom from reoperation was 97% (95% CI, 94%-99%) at 5 years post-PVR and 91% (95% CI, 85%-95%) at 10 years. Mechanical PVR is associated with a limited risk of valvular thrombosis. Thrombolysis was an effective treatment in the majority. Copyright © 2017 The American Association for Thoracic Surgery. Published by Elsevier Inc. All rights reserved.

  3. Integrity monitoring of vehicle positioning in urban environment using RTK-GNSS, IMU and speedometer

    Science.gov (United States)

    El-Mowafy, Ahmed; Kubo, Nobuaki

    2017-05-01

    Continuous and trustworthy positioning is a critical capability for advanced driver assistance systems (ADAS). To achieve continuous positioning, methods such as global navigation satellite systems real-time kinematic (RTK), Doppler-based positioning, and positioning using low-cost inertial measurement unit (IMU) with car speedometer data are combined in this study. To ensure reliable positioning, the system should have integrity monitoring above a certain level, such as 99%. Achieving this level when combining different types of measurements that have different characteristics and different types of errors is a challenge. In this study, a novel integrity monitoring approach is presented for the proposed integrated system. A threat model of the measurements of the system components is discussed, which includes both the nominal performance and possible fault modes. A new protection level is presented to bound the maximum directional position error. The proposed approach was evaluated through a kinematic test in an urban area in Japan with a focus on horizontal positioning. Test results show that by integrating RTK, Doppler with IMU/speedometer, 100% positioning availability was achieved. The integrity monitoring availability was assessed and found to meet the target value where the position errors were bounded by the protection level, which was also less than an alert level, indicating the effectiveness of the proposed approach.

  4. Integrity monitoring of vehicle positioning in urban environment using RTK-GNSS, IMU and speedometer

    International Nuclear Information System (INIS)

    El-Mowafy, Ahmed; Kubo, Nobuaki

    2017-01-01

    Continuous and trustworthy positioning is a critical capability for advanced driver assistance systems (ADAS). To achieve continuous positioning, methods such as global navigation satellite systems real-time kinematic (RTK), Doppler-based positioning, and positioning using low-cost inertial measurement unit (IMU) with car speedometer data are combined in this study. To ensure reliable positioning, the system should have integrity monitoring above a certain level, such as 99%. Achieving this level when combining different types of measurements that have different characteristics and different types of errors is a challenge. In this study, a novel integrity monitoring approach is presented for the proposed integrated system. A threat model of the measurements of the system components is discussed, which includes both the nominal performance and possible fault modes. A new protection level is presented to bound the maximum directional position error. The proposed approach was evaluated through a kinematic test in an urban area in Japan with a focus on horizontal positioning. Test results show that by integrating RTK, Doppler with IMU/speedometer, 100% positioning availability was achieved. The integrity monitoring availability was assessed and found to meet the target value where the position errors were bounded by the protection level, which was also less than an alert level, indicating the effectiveness of the proposed approach. (paper)

  5. Bayesian Inference for Source Term Estimation: Application to the International Monitoring System Radionuclide Network

    Science.gov (United States)

    2014-10-01

    Laboratories (CRL) medical isotope production facility. The sampling of the resulting posterior distribution of the source parameters is un- dertaken...International Monitoring System radionuclide network used for Case 2. The location of the Xe-133 tracer source (red marker) was at Chalk River Laboratories ...space. 5 Applications The International Monitoring System (IMS) consists of a comprehensive network of seismic, hydroacoustic , infrasound, and

  6. Electromagnetic Design and Optimization of Directivity of Stripline Beam Position Monitors for the High Luminosity Large Hadron Collider

    CERN Document Server

    Draskovic, Drasko; Jones, Owain Rhodri; Lefèvre, Thibaut; Wendt, Manfred

    2015-01-01

    This paper presents the preliminary electromagnetic design of a stripline Beam Position Monitor (BPM) for the High Luminosity program of the Large Hadron Collider (HL-LHC) at CERN. The design is fitted into a new octagonal shielded Beam Screen for the low-beta triplets and is optimized for high directivity. It also includes internal Tungsten absorbers, required to reduce the energy deposition in the superconducting magnets. The achieved broadband directivity in wakefield solver simulations presents significant improvement over the directivity of the current stripline BPMs installed in the LHC.

  7. Evaluation of sensitivity evaluation of a contamination monitor for use in monitoring of internal exposure of workers in nuclear medicine

    International Nuclear Information System (INIS)

    Dantas, Bernando Maranhao; Assis, Janima Cruz de; Oliveira, Salomao Marques de; Dantas, Ana Leticia Almeida

    2014-01-01

    In practice of nuclear medicine, expert personnel routinely handle radiopharmaceuticals for diagnosis and radiotherapy. The control of intakes of radionuclides by workers can be performed through internal dosimetry techniques, as an integral part of the radiation protection program of the installation. The use of radiopharmaceuticals for diagnostic and therapeutic purposes in vivo and in vitro in Brazil is regulated by CNEN-NE Standards and 3:05 CNEN-NN 3.01. The International Atomic Energy Agency (IAEA) recommends the establishment of an internal monitoring program on workers, especially those subject to possible exposure to annual effective doses greater than 1 mSv. Note that, currently, in Brazil, are not available qualified laboratories to provide internal monitoring services in all regions in the country, if it were applied by CNEN, the requirement for internal monitoring of workers. This paper presents the development of a simple and low-cost methodology for in vivo monitoring of 131 I in the thyroid. The proposed methodology is the use of portable monitor of surface contamination, equipment available and routinely used in all nuclear medicine services in Brazil. The monitor is calibrated with neck-thyroid simulator developed at the Laboratory of In Vivo Monitoring of IRD/CNEN-RJ. The equipment tested is suitable for application in in vivo occupational monitoring thyroid. This conclusion is based on the fact that the detection system has sufficient sensitivity for monitoring up to seven days after the incorporation of the radionuclide and guarantees 131 I detection in values that result in effective doses below 1 mSv for the exposure scenarios adopted

  8. Stability study of the higher order mode beam position monitors at the Accelerating cavities at FLASH

    CERN Document Server

    Shi, L; Jones., R M

    2014-01-01

    erating cavities at FLASH linac, DESY, are equipped with electronics for beam position monitoring, which are based on HOM signals from special couplers. These monitors provide the beam position without additional vacuum components and at low cost. Moreover, they can be used to align the beam in the cavities to reduce the HOM effects on the beam. However, the HOMBPM (Higher Order Mode based Beam Position Monitor) shows an instability problem over time. In this paper, we will present the status of studies on this issue. Several methods are utilized to calibrate the HOMBPMs. These methods include DLR (Direct Linear Regression), and SVD (Singular Value Decomposition). We found that SVD generally is more suitable for HOMBPM calibration. We focus on the HOMBPMs at 1.3 GHz cavities. Techniques developed here are applicable to 3.9 ...

  9. Development of beam position monitor of the transport line from LINAC to AR in TRISTAN

    International Nuclear Information System (INIS)

    Tejima, M.; Satoh, M.; Mori, K.

    1994-01-01

    We constructed and installed 9 Beam Position Monitors (BPM) having four strip-lines along the beam transport line from the linac to the accumulating ring (AR) last summer. Every signal was gathered in the local control room, the beam signal is measured by using the digitizing oscilloscope and sent to the micro-computer(μ-com) through the GPIB. The picture of beam positions on the μ-com terminal is converted to the video signal and transmitted to a TV monitor at the central control room. (author)

  10. MONITORING EXTERNAL AND INTERNAL LOADS OF BRAZILIAN SOCCER REFEREES DURING OFFICIAL MATCHES

    Directory of Open Access Journals (Sweden)

    Eduardo C. Costa

    2013-09-01

    Full Text Available This study aimed to assess the external and internal loads of Brazilian soccer referees during official matches. A total of 11 field referees (aged 36.2 ± 7.5 years were monitored during 35 matches. The external (distance covered, mean and maximal speed and internal load parameters (session ratings of perceived exertion [RPE] training load [TL], Edwards' TL, and time spent in different heart rate [HR] zones were assessed in 3-4 matches per referee. External load parameters were measured using a wrist Global Positioning System (GPS receiver. No differences in distance covered (5.219 ± 205 vs. 5.230 ± 237 m and maximal speed (19.3 ± 1.0 vs. 19.4 ± 1.4 km·h-1 were observed between the halves of the matches (p > 0.05. However, the mean speed was higher in the first half of the matches (6.6 ± 0.4 vs. 6.4 ± 0.3 km·h-1 (p 80% of HRmax. Nonetheless, the time spent at 90-100% of HRmax was higher in the first half (59.9 vs. 52.3% (p < 0.05. Significant correlations between session RPE TL and distance covered at 90-100% of HRmax (r = 0.62 and session RPE TL and maximal speed (r = 0.54 (p < 0.05 were noted. Furthermore, there was a positive correlation between session RPE TL and Edwards' TL (r = 0.61 (p < 0.05. Brazilian soccer referees demonstrated high external and internal load demands during official matches. The portable GPS/HR monitors and session RPE method can provide relevant information regarding the magnitude of the physiological strain during official matches

  11. Pilot study: Assessing the effect of continual position monitoring technology on compliance with patient turning protocols.

    Science.gov (United States)

    Schutt, Suann Cirigliano; Tarver, Christine; Pezzani, Michelle

    2018-01-01

    The study aim was to evaluate if continual patient position monitoring, taking into account self-turns and clinician-assisted turns, would increase the percentage of time a patient's position changed at least every 2 hr. While patient turning has clinical benefits, current models to help staff remember to turn patients, such as "turn clocks" and timers, have not resulted in high compliance with turning protocols. In addition, reminders are based on arbitrary 2-hr windows (such as turning on "even" hours) rather than on individual patient activity, including self-turns. This is a first inpatient, non-randomized, pre-/postintervention study. Data collection occurred from May 2013-February 2014 on a 39-bed medical unit in a community hospital. Baseline patient turning data were recorded by a sensor; however, the patient data were not displayed at the nurses' station to establish compliance with the hospital's turning protocol. Postintervention, patient position information was wirelessly displayed on nurses' station computer monitors in real time. A Student t test was used to compare baseline to postintervention "mean time in compliance." Data from 138 patients ( N  =   7,854 hr of monitoring) were collected. The baseline phase yielded 4,322 hr of position monitoring data and the postintervention phase yielded 3,532 hr of data. Statistically significant improvement was demonstrated in the percentage of time a patient's position changed at least every 2 hr from baseline to postintervention.

  12. Beam position monitoring in the AGS Linac to Booster transfer line

    International Nuclear Information System (INIS)

    Shea, T.J.; Brodowski, J.; Witkover, R.

    1991-01-01

    A beam position monitor system has been developed and used in the commissioning of Brookhaven's Linac to Booster transfer line. This line transports a chopped, RF modulated H- beam from the 200 MeV Linac to the AGS Booster. Over a 15dB dynamic range in beam current, the position monitor system provides a real-time, normalized position signal with an analog bandwidth of about 20 MHz. Seven directional coupler style pickups are installed in the line with each pickup sensing both horizontal and vertical position. Analog processing electronics are located in the tunnel and incorporate the amplitude modulation to phase modulation normalization technique. To avoid interference from the 200 MHz linac RF system, processing is performed at 400 MHz. This paper provides a system overview and report results from the commissioning experience

  13. INTERNAL CONTROL AND MONITORING. CONCEPTS, TOOLS AND MODELS OF IMPLEMENTATION

    Directory of Open Access Journals (Sweden)

    Ana Monica POP

    2016-12-01

    Full Text Available The internal control system is currently under international control in a proper manner since the early 90s, when The Internal Control-Integrated Framework was published in 1992 by the Committee of Sponsoring Organizations of the Treadway Commission knowing over the years a series of steps that have marked key moments in shaping this system designed in particular to protect the financial resources of the institutions.

  14. International consensus on use of continuous glucose monitoring

    DEFF Research Database (Denmark)

    Danne, Thomas; Nimri, Revital; Battelino, Tadej

    2017-01-01

    microvascular and macrovascular complications. Continuous glucose monitoring (CGM), either from real-time use (rtCGM) or intermittently viewed (iCGM), addresses many of the limitations inherent in HbA1c testing and self-monitoring of blood glucose. Although both provide themeans to move beyond the HbA1c...... measurement as the sole marker of glycemic control, standardized metrics for analyzing CGM data are lacking. Moreover, clear criteria for matching people with diabetes to themost appropriate glucose monitoring methodologies, as well as standardized advice about howbest to use the new information they provide...

  15. A fast non-intercepting linac beam position and current monitor

    International Nuclear Information System (INIS)

    Hansen, J.W.; Wille, M.

    1982-01-01

    A non-intercepting beam monitor consisting of four detecting loops is used to determine the spatial postion and current of a pulsed beam from an electron linear accelerator. The monitor detects the magnetic field radiated by the substructure of the electron bunches created by the accelerating microwave. The detecting loops are interconnected two by two, by means of two coaxial hybrid junctions, the two sets positioned perpendicular to each other. By means of the two signals from the diametrically positioned detecting loops, a good spatial displacement and current monitoring sensitivity are achieved by subtracting one signal from the other and adding the two signals, respectively. For displacements below 2 mm from the center axis an average sensitivity of 0.5 mV/mm x mA is measured, whereas displacements more than 2 mm yields 1.3 mV/mm x mA. A sensitivity of 0.2 mV/mA in current monitoring is measured, and the rise time of the monitored pulse signal is better than 5 ns measured from 10 to 90% of the pulse height. Design strategy and performance of the monitor are described. (orig.)

  16. Sea floor litter monitoring : International Bottom Trawl Survey 2016

    OpenAIRE

    Hal, van, Ralf

    2017-01-01

    The Marine Strategy Framework Directive (MSFD) requires the European Member States to develop programmes of measures to achieve or maintain Good Environmental Status (GES) in European Seas. To be able to evaluate the quality state of the marine waters on a regular basis and the effect of measures taken, monitoring programs for MSFD descriptors and indicators have been established by the Member states. GES is described by 11 descriptors, and marine litter is one of them. The Dutch monitoring p...

  17. Partner Positioning: Examining International Higher Education Partnerships through a Mutuality Lens

    Science.gov (United States)

    George Mwangi, Chrystal A.

    2017-01-01

    Scholarship on international higher education partnerships is often framed by strategic management and organization theories. These approaches are useful, but can minimize how power dynamics and positioning of partners impact engagement and outcomes. This study uses qualitative inquiry to examine 60 international higher education partnerships…

  18. Effects of School-Wide Positive Behavior Support on Internalizing Problems: Current Evidence and Future Directions

    Science.gov (United States)

    McIntosh, Kent; Ty, Sophie V.; Miller, Lynn D.

    2014-01-01

    School-wide Positive Behavior Support (SWPBS) has a large evidence base for preventing and addressing externalizing problem behavior, but there is little research examining its effects on internalizing problems, such as anxiety and depression. Given the prevalence of internalizing problems in today's children and youth, it is worthwhile to examine…

  19. Some international activities in environmental health monitoring and surveillance.

    Science.gov (United States)

    Vouk, V B; Ozolins, G; Hasegawa, Y; Pařizek, J

    1982-12-01

    Environmental health monitoring and surveillance include activities such as collection of information on the production and use of chemicals; preparation of inventories of waste discharges; measurement of physical, chemical and biological agents in air, water and food, at work place and at home; epidemiological investigations, and collection and analysis of environmental, and health statistical data. There are two main objectives of these activities: estimation of human exposure to potentially harmful environmental factors and timely detection of adverse health effects; and the assessment of environmental conditions in relation to established guidelines and standards. Environmental health monitoring and surveillance projects initiated, organized and implemented by the Specialized Agencies and other bodies of the United Nations system include monitoring of air and water quality and of food and animal feed contamination; pilot projects on air pollution exposure assessment and biological monitoring; and ionizing radiation surveillance. Principles of environmental and health monitoring in occupational environment, and of monitoring and surveillance of environmental health effects are outlined. Two examples are provided of national environmental health surveillance systems.

  20. Renewal of beam position monitor electronics of the SPring-8 storage ring

    International Nuclear Information System (INIS)

    Sasaki, Shigeki; Fujita, Takahiro

    2007-01-01

    Signal processing electronics for the beam position monitors (BPM) of the SPring-8 Storage Ring were renewed during the summer shutdown period of 2006. The configurations of the electronics of before and after the alteration are described. The evaluation of the performance of the electronics is shown with the data taken by using the actual beams. (author)

  1. Multipoint alignment monitoring with amorphous silicon position detectors in a complex light path

    International Nuclear Information System (INIS)

    Alberdi, J.; Arce, P.; Barcala, J.M.; Calvo, E.; Ferrando, A.; Josa, M.I.; Molinero, A.; Navarrete, J.; Oller, J.C.; Yuste, C.; Calderon, A.; Gomez, G.; Gonzalez-Sanchez, F.J.; Martinez-Rivero, C.; Matorras, F.; Rodrigo, T.; Ruiz-Arbol, P.; Sobron, M.; Vila, I.; Virto, A.L.

    2010-01-01

    This document presents an application of the new generation of amorphous silicon position detecting (ASPD) sensors to multipoint alignment. Twelve units are monitored along a 20 m long laser beam, where the light path is deflected by 90 o using a pentaprism.

  2. Results from multipoint alignment monitoring using the new generation of amorphous silicon position detectors

    International Nuclear Information System (INIS)

    Alberdi, J.; Arce, P.; Barcala, J.M.; Calvo, E.; Ferrando, A.; Josa, M.I.; Molinero, A.; Navarrete, J.; Oller, J.C.; Yuste, C.; Calderon, A.; Gomez, G.; Gonzalez-Sanchez, F.J.; Martinez-Rivero, C.; Matorras, F.; Rodrigo, T.; Ruiz-Arbol, P.; Sobron, M.; Vila, I.; Virto, A.L.

    2008-01-01

    We present the measured performance of a new generation of large sensitive area (28x28 mm 2 ) semitransparent amorphous silicon position detector sensors. More than 100 units have been characterized. They show a very high performance. To illustrate a multipoint application, we present results from the monitoring of five sensors placed in a 5.5-m-long light path

  3. Length of stay for patients undergoing invasive electrode monitoring with stereoelectroencephalography and subdural grids correlates positively with increased institutional profitability.

    Science.gov (United States)

    Chan, Alvin Y; Kharrat, Sohayla; Lundeen, Kelly; Mnatsakanyan, Lilit; Sazgar, Mona; Sen-Gupta, Indranil; Lin, Jack J; Hsu, Frank P K; Vadera, Sumeet

    2017-06-01

    Lowering the length of stay (LOS) is thought to potentially decrease hospital costs and is a metric commonly used to manage capacity. Patients with epilepsy undergoing intracranial electrode monitoring may have longer LOS because the time to seizure is difficult to predict or control. This study investigates the effect of economic implications of increased LOS in patients undergoing invasive electrode monitoring for epilepsy. We retrospectively collected and analyzed patient data for 76 patients who underwent invasive monitoring with either subdural grid (SDG) implantation or stereoelectroencephalography (SEEG) over 2 years at our institution. Data points collected included invasive electrode type, LOS, profit margin, contribution margins, insurance type, and complication rates. LOS correlated positively with both profit and contribution margins, meaning that as LOS increased, both the profit and contribution margins rose, and there was a low rate of complications in this patient group. This relationship was seen across a variety of insurance providers. These data suggest that LOS may not be the best metric to assess invasive monitoring patients (i.e., SEEG or SDG), and increased LOS does not necessarily equate with lower or negative institutional financial gain. Further research into LOS should focus on specific specialties, as each may differ in terms of financial implications. Wiley Periodicals, Inc. © 2017 International League Against Epilepsy.

  4. A prototype cavity beam position monitor for the CLIC Main Beam

    CERN Document Server

    Cullinany , F; Joshi, N; Lyapin, A; Bastard, D; Calvo, E; Chritin, N; Guillot-Vignot, F; Lefevre, T; Søby, L; Wendt, M; Lunin, A; Yakovlev, V P; Smith, S

    2012-01-01

    The Compact Linear Collider (CLIC) places unprecedented demands on its diagnostics systems. A large number of cavity beam position monitors (BPMs) throughout the main linac and beam delivery system (BDS) must routinely perform with 50 nm spatial resolution. Multiple position measurements within a single 156 ns bunch train are also required. A prototype low-Q cavity beam position monitor has been designed and built to be tested on the CLIC Test Facility (CTF3) probe beam. This paper presents the latest measurements of the prototype cavity BPM and the design and simulation of the radio frequency (RF) signal processing electronics with regards to the final performance. Installation of the BPM in the CTF3 probe beamline is also discussed.

  5. Single-shot beam-position monitor for x-ray free electron laser

    Science.gov (United States)

    Tono, Kensuke; Kudo, Togo; Yabashi, Makina; Tachibana, Takeshi; Feng, Yiping; Fritz, David; Hastings, Jerome; Ishikawa, Tetsuya

    2011-02-01

    We have developed an x-ray beam-position monitor for detecting the radiation properties of an x-ray free electron laser (FEL). It is composed of four PIN photodiodes that detect backscattered x-rays from a semitransparent diamond film placed in the beam path. The signal intensities from the photodiodes are used to compute the beam intensity and position. A proof-of-principle experiment at a synchrotron light source revealed that the error in the beam position is reduced to below 7 μm by using a nanocrystal diamond film prepared by plasma-enhanced chemical vapor deposition. Owing to high dose tolerance and transparency of the diamond film, the monitor is suitable for routine diagnostics of extremely intense x-ray pulses from the FEL.

  6. Peru and Guatemala Internal Midline Monitoring Assessment of Reading

    Data.gov (United States)

    US Agency for International Development — Save the Children is implementing Leer Juntos, a USAID-funded three-year project targeting rural, indigenous communities in Guatemala and Peru with the objective of...

  7. Accuracy Analysis of Precise Point Positioning of Compass Navigation System Applied to Crustal Motion Monitoring

    Science.gov (United States)

    Wang, Yuebing

    2017-04-01

    Based on the observation data of Compass/GPSobserved at five stations, time span from July 1, 2014 to June 30, 2016. UsingPPP positioning model of the PANDA software developed by Wuhan University,Analyzedthe positioning accuracy of single system and Compass/GPS integrated resolving, and discussed the capability of Compass navigation system in crustal motion monitoring. The results showed that the positioning accuracy in the east-west directionof the Compass navigation system is lower than the north-south direction (the positioning accuracy de 3 times RMS), in general, the positioning accuracyin the horizontal direction is about 1 2cm and the vertical direction is about 5 6cm. The GPS positioning accuracy in the horizontal direction is better than 1cm and the vertical direction is about 1 2cm. The accuracy of Compass/GPS integrated resolving is quite to GPS. It is worth mentioning that although Compass navigation system precision point positioning accuracy is lower than GPS, two sets of velocity fields obtained by using the Nikolaidis (2002) model to analyze the Compass and GPS time series results respectively, the results showed that the maximum difference of the two sets of velocity field in horizontal directions is 1.8mm/a. The Compass navigation system can now be used to monitor the crustal movement of the large deformation area, based on the velocity field in horizontal direction.

  8. Cycle 24 COS NUV Internal/External Wavelength Scale Monitor

    Science.gov (United States)

    Fischer, William J.

    2018-02-01

    We report on the monitoring of the COS NUV wavelength scale zero-points during Cycle 24 in program 14859. Select cenwaves were monitored for all NUV gratings. The target and cenwaves have remained the same since Cycle 18, with changes only to the target acquisition sequence and the number of visits per cycle. With minor exceptions, measured offsets are within the error goals. The declining sensitivity of the G285M grating is beginning to present a challenge for precise cross-correlation.

  9. Preliminry results of the 1975 international personnel monitoring survey

    International Nuclear Information System (INIS)

    Becker, K.

    1975-11-01

    About 70 detailed questions have been answered in mid-1975 by 83 personnel monitoring services in 33 countries, representing almost half a million, or approximately 28 percent, of the world's total radiation workers, as well as by 11 customers of U. S. commercial services. Extensive data are given on many questions regarding the current system in use, future plans, and experiences, for example on the type(s) of TLD, film and readout instrumentation; monitoring period; applications for extremity and environmental monitoring; advantages and disadvantages of various systems; R and D projects; experience with beta and neutron dosimetry; intentional fake exposures; lower and upper dose limits; recordkeeping; and reporting of the results. The larger services in the advanced countries lead in the transition from film to TLD. More than half of the radiation workers already wear TLDs, or will do so within about two years. Important unsolved problems are fast neutron monitoring and the low information content and high initial cost of TLD. The trend is towards large, centralized, automatic services and recordkeeping, with extensive computer use for evaluation and data handling. There is a need for better performance standards and testing, and more information exchange and cooperation between services. (auth)

  10. An International Haze-Monitoring Network for Students.

    Science.gov (United States)

    Mims, Forrest M.

    1999-01-01

    Describes the haze-monitoring program that was added to the protocols of the Global Learning and Observations to Benefit the Environment (GLOBE) Program. Finds that sun photometry provides a convenient means for allowing students to perform hands-on science while learning about various topics in history, electronics, algebra, statistics, graphing,…

  11. The potential use of domestic safeguards interior monitors in International Safeguards

    International Nuclear Information System (INIS)

    Williams, J.D.; Dupree, S.A.; Sonnier, C.S.

    1998-01-01

    An important future element of International Safeguards instrumentation is expected to be the merging of containment/surveillance and nondestructive assay equipment with domestic physical protection equipment into integrated systems, coupled with remote monitoring. Instrumentation would include interior monitoring and assessment and entry/exit monitoring. Of particular importance is the application of interior monitors in spaces of declared inactivity; for example, in nuclear material storage locations that are entered infrequently. The use of modern interior monitors in International Safeguards offers potential for improving effectiveness and efficiency. Within the context of increased cooperation, one can readily envision increased interaction between International Safeguards and Domestic Safeguards, including increased joint use of State System of Accounting and Control data

  12. Current sedation and monitoring practice for colonoscopy: an International Observational Study (EPAGE)

    DEFF Research Database (Denmark)

    Froehlich, F; Harris, JK; Wietlisbach, V

    2006-01-01

    in endoscopy centers internationally. PATIENTS AND METHODS: This observational study included consecutive patients referred for colonoscopy at 21 centers in 11 countries. Endoscopists reported sedation and monitoring practice, using a standard questionnaire for each patient. RESULTS: 6004 patients were...

  13. Processing of Internal and External Signals for Performance Monitoring in the Context of Emotional Faces.

    Science.gov (United States)

    Christian Valt, Christian; Palazova, Marina; Stürmer, Birgit

    2017-01-01

    Performance monitoring can be based on internal or external signals. We recorded event-related potentials (ERPs) to investigate whether relating performance to external signals affects internal performance monitoring. Thirty participants performed a task in which responses were followed by faces whose expressions were partially contingent upon performance. Instructions given to half of the participants mentioned a link between task performance and the upcoming face expression. Instructed participants showed smaller error-related negativity (Ne/ERN) to erroneous responses and larger N170 to faces as compared to participants in the not-instructed group. In addition, we observed a correlation between ΔNe/ERN and P1-latency benefit for angry faces after errors. Taken together, processing of internally generated signals for performance monitoring is reduced by instructions referring to an emotional face. Furthermore, we relate the correlation between the magnitude of internal monitoring and facilitation in processing angry faces to priming induced by the negative affective meaning of errors.

  14. A contactless positioning system for monitoring discontinuities in three dimensions with geological and geotechnical applications.

    Science.gov (United States)

    Rinaldi-Montes, Natalia; Rowberry, Matt; Frontera, Carlos; Baroň, Ivo; Garcés, Javier; Blahůt, Jan; Pérez-López, Raúl; Pennos, Christos; Martí, Xavi

    2017-07-01

    In this paper, a contactless positioning system is presented which has been designed to monitor the kinematic behavior of mechanical discontinuities in three dimensions. The positioning system comprises a neodymium magnet, fixed on one side of a discontinuity, and a magnetoresistive sensing array, fixed on the opposing side. Each of the anisotropic magnetoresistive sensors in the sensing array records the magnetic field along three orthogonal directions. The positioning system intrinsically generates compact data packages which are transmitted effectively using a range of standard wireless telecommunication technologies. These data are then modeled using a global least squares fitting procedure in which the adjustable parameters are represented by the position and orientation of the neodymium magnet. The instrumental resolution of the positioning system can be tuned depending on the strength of the magnetic field generated by the neodymium magnet and the distance between the neodymium magnet and the magnetoresistive sensing array. For a typical installation, the displacement resolution is shown to be circa 10 μm while the rotation resolution is circa 0.1°. The first permanently deployed positioning system was established in June 2016 to monitor the behavior of an N-S trending fault located at the contact between the eastern Alps and the Vienna Basin. The robust design of the positioning system is demonstrated by the fact that no interruptions in the broadcasted data streams have occurred since its installation. It has a range of potential applications in many areas of basic and applied research including geology, geotechnical engineering, and structural health monitoring.

  15. A contactless positioning system for monitoring discontinuities in three dimensions with geological and geotechnical applications

    Science.gov (United States)

    Rinaldi-Montes, Natalia; Rowberry, Matt; Frontera, Carlos; BaroÅ, Ivo; Garcés, Javier; Blahůt, Jan; Pérez-López, Raúl; Pennos, Christos; Martí, Xavi

    2017-07-01

    In this paper, a contactless positioning system is presented which has been designed to monitor the kinematic behavior of mechanical discontinuities in three dimensions. The positioning system comprises a neodymium magnet, fixed on one side of a discontinuity, and a magnetoresistive sensing array, fixed on the opposing side. Each of the anisotropic magnetoresistive sensors in the sensing array records the magnetic field along three orthogonal directions. The positioning system intrinsically generates compact data packages which are transmitted effectively using a range of standard wireless telecommunication technologies. These data are then modeled using a global least squares fitting procedure in which the adjustable parameters are represented by the position and orientation of the neodymium magnet. The instrumental resolution of the positioning system can be tuned depending on the strength of the magnetic field generated by the neodymium magnet and the distance between the neodymium magnet and the magnetoresistive sensing array. For a typical installation, the displacement resolution is shown to be circa 10 μm while the rotation resolution is circa 0.1°. The first permanently deployed positioning system was established in June 2016 to monitor the behavior of an N-S trending fault located at the contact between the eastern Alps and the Vienna Basin. The robust design of the positioning system is demonstrated by the fact that no interruptions in the broadcasted data streams have occurred since its installation. It has a range of potential applications in many areas of basic and applied research including geology, geotechnical engineering, and structural health monitoring.

  16. The Formation of a Positive International Image of Country as a Means of Enhancing Competitiveness

    Directory of Open Access Journals (Sweden)

    Novikova Ludmyla V.

    2017-11-01

    Full Text Available The article is aimed at studying the essence of the concept of «image of the state» and substantiating the conceptual model of forming a positive international image of country as a means of enhancing competitiveness in the international market. The essence of the concept of «image of the State» has been defined. The factors influencing the formation of the international image of country have been distributed and systematized. The principles on which the process of formation of country image of modern format, receiving public recognition and adequate international estimation, have been allocated. A conceptual model of formation of positive international image of country, based on the hypothesis of influence of positive image on creation of significant competitive advantages in the international market of goods and services, has been proposed. The key features of the model are defined as: clear distribution of the roles of the stakeholders of national image – subjects of the global economic system, level of their involvement in the process of formation and integration of the State economy into the system of international institutions.

  17. Proceedings of the international workshop on monitoring forest degradation in Southeast Asia

    Science.gov (United States)

    Leif A. Mortenson; James J. Halperin; Patricia N. Manley; Rich L. Turner

    2013-01-01

    The international workshop on monitoring forest degradation in Southeast Asia provided a forum for discussion of the technical, social and political challenges and successes that have occurred during recent work in sub-national forest degradation monitoring. The 2012 workshop, held in Bangkok, Thailand, followed recent US Forest Service/LEAF (USAID's Lowering...

  18. The pre-operational monitoring - how useful are recommendations of international organizations and various national programs

    International Nuclear Information System (INIS)

    Mihailovic, M.

    1980-01-01

    National legislation and the preoperational monitoring program around Nuclear Power Plant Krsko are described. The usefulness of international recommendations and various national preoperational monitoring programs is examined. Modifications are described which were introduced with the aim of identifying the site specific critical exposure pathways. The role of qualified and experienced experts is discussed. (H.K.)

  19. Update on Monitoring Technologies for International Safeguards and Fissile Material Verification

    International Nuclear Information System (INIS)

    Croessmann, C. Dennis; Glidewell, Don D.; Mangan, Dennis L.; Smathers, Douglas C.

    1999-01-01

    Monitoring technologies are playing an increasingly important part in international safeguards and fissile material verification. The developments reduce the time an inspector must spend at a site while assuring continuity of knowledge. Monitoring technologies' continued development has produced new seal systems and integrated video surveillance advances under consideration for Trilateral Initiative use. This paper will present recent developments for monitoring systems at Embalse, Argentina, VNHEF, Sarov, Russian, and Savannah River Site, Aiken, South Carolina

  20. Improved design and in-situ measurements of new beam position monitors for Indus-2

    Science.gov (United States)

    Kumar, M.; Babbar, L. K.; Holikatti, A. C.; Yadav, S.; Tyagi, Y.; Puntambekar, T. A.; Senecha, V. K.

    2018-01-01

    Beam position monitors (BPM) are important diagnostic devices used in particle accelerators to monitor position of the beam for various applications. Improved version of button electrode BPM has been designed using CST Studio Suite for Indus-2 ring. The new BPMs are designed to replace old BPMs which were designed and installed more than 12 years back. The improved BPMs have higher transfer impedance, resonance free output signal, equal sensitivity in horizontal and vertical planes and fast decaying wakefield as compared to old BPMs. The new BPMs have been calibrated using coaxial wire method. Measurement of transfer impedance and time domain signals has also been performed in-situ with electron beam during Indus-2 operation. The calibration and beam based measurements results showed close agreement with the design parameters. This paper presents design, electromagnetic simulations, calibration result and in-situ beam based measurements of newly designed BPMs.

  1. An experimental evaluation of monochromatic x-ray beam position monitors at diamond light source

    Energy Technology Data Exchange (ETDEWEB)

    Bloomer, Chris, E-mail: chris.bloomer@diamond.ac.uk; Rehm, Guenther; Dolbnya, Igor P. [Diamond Light Source Ltd, Oxfordshire (United Kingdom)

    2016-07-27

    Maintaining the stability of the X-ray beam relative to the sample point is of paramount importance for beamlines and users wanting to perform cutting-edge experiments. The ability to detect, and subsequently compensate for, variations in X-ray beam position with effective diagnostics has multiple benefits: a reduction in commissioning and start-up time, less ‘down-time’, and an improvement in the quality of acquired data. At Diamond Light Source a methodical evaluation of a selection of monochromatic X-ray Beam Position Monitors (XBPMs), using a range of position detection techniques, and from a range of suppliers, was carried out. The results of these experiments are presented, showing the measured RMS noise on the position measurement of each device for a given flux, energy, beam size, and bandwidth. A discussion of the benefits and drawbacks of each of the various devices and techniques is also included.

  2. An experimental evaluation of monochromatic x-ray beam position monitors at diamond light source

    International Nuclear Information System (INIS)

    Bloomer, Chris; Rehm, Guenther; Dolbnya, Igor P.

    2016-01-01

    Maintaining the stability of the X-ray beam relative to the sample point is of paramount importance for beamlines and users wanting to perform cutting-edge experiments. The ability to detect, and subsequently compensate for, variations in X-ray beam position with effective diagnostics has multiple benefits: a reduction in commissioning and start-up time, less ‘down-time’, and an improvement in the quality of acquired data. At Diamond Light Source a methodical evaluation of a selection of monochromatic X-ray Beam Position Monitors (XBPMs), using a range of position detection techniques, and from a range of suppliers, was carried out. The results of these experiments are presented, showing the measured RMS noise on the position measurement of each device for a given flux, energy, beam size, and bandwidth. A discussion of the benefits and drawbacks of each of the various devices and techniques is also included.

  3. Large Size High Performance Transparent Amorphous Silicon Sensors for Laser Beam Position Detection and Monitoring

    International Nuclear Information System (INIS)

    Calderon, A.; Martinez Rivero, C.; Matorras, F.; Rodrigo, T.; Sobron, M.; Vila, I.; Virto; Alberdi, J.; Arce, P.; Barcala, J. M.; Calvo, E.; Ferrando, A.; Josa, M. I.; Luque, J. M.; Molinero, A.; Navarrete, J.; Oller, J. C.; Kohler, C.; Lutz, B.; Schubert, M. B.

    2006-01-01

    We present the measured performance of a new generation of semitransparente amorphous silicon position detectors. They have a large sensitive area (30 x 30 mm2) and show good properties such as a high response (about 20 mA/W), an intinsic position resolution better than 3 m, a spatial point reconstruction precision better than 10 m, deflection angles smaller than 10 rad and a transmission power in the visible and NIR higher than 70%. In addition, multipoint alignment monitoring, using up to five sensors lined along a light path of about 5 meters, can be achieved with a resolution better than 20m. (Author)

  4. Pilot study: Assessing the effect of continual position monitoring technology on compliance with patient turning protocols

    OpenAIRE

    Schutt, Suann Cirigliano; Tarver, Christine; Pezzani, Michelle

    2017-01-01

    Abstract Aim The study aim was to evaluate if continual patient position monitoring, taking into account self‐turns and clinician‐assisted turns, would increase the percentage of time a patient's position changed at least every 2 hr. Background While patient turning has clinical benefits, current models to help staff remember to turn patients, such as “turn clocks” and timers, have not resulted in high compliance with turning protocols. In addition, reminders are based on arbitrary 2‐hr windo...

  5. Construction and measurement techniques for the APS LEUTL project RF beam position monitors.

    Energy Technology Data Exchange (ETDEWEB)

    Gorski, A.

    1999-04-20

    The design, construction, and assembly procedure of 24 rf beam position monitors used in the Advanced Photon Source low-energy undulator test line and linear accelerator (linac) are described. Beam stability as well as beam positioning capabilities are essential to the LEUTL project. A design objective of the LEUTL facility is to achieve better than 1-{micro}m resolution. The highest care was used in the mechanical fabrication and assembly of the BPM units. The latest experimental results using these BPMs are presented.

  6. Impedance simulations and measurements on the LHC collimators with embedded beam position monitors

    Directory of Open Access Journals (Sweden)

    N. Biancacci

    2017-01-01

    Full Text Available The LHC collimation system is a critical element for the safe operation of the LHC machine. The necessity of fast accurate positioning of the collimator’s jaws, recently introduced the need to have button beam position monitors directly embedded in the jaws extremities of the LHC tertiary collimators and some secondary collimators. This addition led to a new design of these collimators including ferrites to damp higher order modes instead of rf fingers. In this work we will present the impedance bench measurements and simulations on a TCT (Transverse Tertiary Collimator prototype including estimations for beam stability for the LHC.

  7. Beam Position and Phase Monitors Characterized and Installed in the LANSCE CCL

    Energy Technology Data Exchange (ETDEWEB)

    Gilpatrick, John D [Los Alamos National Laboratory; Kutac, Vincent G. [Los Alamos National Laboratory; Martinez, Derwin [Los Alamos National Laboratory; McCrady, Rodney C. [Los Alamos National Laboratory; O' Hara, James F. [Los Alamos National Laboratory; Olivas, Felix R. [Los Alamos National Laboratory; Shurter, Robert B. [Los Alamos National Laboratory; Watkins, Heath A. [Los Alamos National Laboratory

    2012-04-11

    The Los Alamos Neutron Science Center - Risk Mitigation Project is in the process of replacing older Coupled-Cavity-Linac (CCL) Beam-Position Monitors (BPMs) with newer Beam Position and Phase Monitors (BPPMs) and their associated electronics and cable plants. In many locations, these older BPMs include a separate Delta-T loop for measuring the beam's central phase and energy. Thirty-one BPPMs have been installed and many have monitored the charged particle beam. The installation of these newer BPPMs is the first step to installing complete BPPM measurement systems. Prior to the installation, a characterization of each BPPM took place. The characterization procedure includes a mechanical inspection, a vacuum testing, and associated electrical tests. The BPPM electrical tests for all four electrodes include contact resistance measurements, Time Domain Reflectometer (TDR) measurements, relative 201.25-MHz phase measurements, and finally a set of position-sensitive mapping measurements were performed which included associated fitting routines. This paper will show these data for a typical characterized BPPM.

  8. Biosecurity and Health Monitoring at the Zebrafish International Resource Center

    OpenAIRE

    Murray, Katrina N.; Varga, Zolt?n M.; Kent, Michael L.

    2016-01-01

    The Zebrafish International Resource Center (ZIRC) is a repository and distribution center for mutant, transgenic, and wild-type zebrafish. In recent years annual imports of new zebrafish lines to ZIRC have increased tremendously. In addition, after 15 years of research, we have identified some of the most virulent pathogens affecting zebrafish that should be avoided in large production facilities, such as ZIRC. Therefore, while importing a high volume of new lines we prioritize safeguarding ...

  9. International research to monitor sustainable forest spatial patterns: proceedings of the 2005 IUFRO World Congress symposium

    Science.gov (United States)

    Kurt Riitters; Christine Estreguil

    2007-01-01

    Presentations from the symposium "International Research to Monitor Sustainable Forest Spatial Patterns," which was organized as part of the International Union of Forest Research Organizations (IUFRO) World Congress in August 2005, are summarized in this report. The overall theme of the World Congress was "Forests in the Balance: Linking Tradition and...

  10. On-line internal corrosion monitoring and data management for remote pipelines: a technology update

    Energy Technology Data Exchange (ETDEWEB)

    Wold, Kjell; Stoen, Roar; Jenssen, Hallgeir [Roxar Flow Measurement AS, Stavanger (Norway); Carvalho, Anna Maria [Roxar do Brasil Ltda., Rio de Janeiro, RJ (Brazil)

    2009-07-01

    Internal corrosion monitoring of remote pipelines can be costly and demanding on resources. Online and non-intrusive monitoring directly on the pipe wall can improve the quality of measurements, make installation more convenient and allow more efficient communication of data. The purpose of this paper is to describe a non-intrusive technology, and show examples on field installations of the system. Furthermore, the non-intrusive technology data can be stored, interpreted and combined with conventional (intrusive) system information, in order to get a full picture of internal corrosion profile, corrosion rate and trends regarding the pipeline being monitored. (author)

  11. National savings and the international investment position: what does the current account tell us?

    Directory of Open Access Journals (Sweden)

    Wim Boonstra

    2008-06-01

    Full Text Available This article discusses the relation between the balance of payments and the international investment position of countries. It starts with the observation that the net international investment position of many countries is developing independently from their current account balances. This phenomenon can be explained by valuechanges of cross border assets and liabilities that are not registered on the balance of payments. These value changes have impact on the net external investment position of a country as soon as the returns on its external assets and liabilities start to diverge. Such divergent developments can be attributed to currency developments,differences of composition of external assets and liabilities and performance effects. These mechanisms are discussed, followed by two case studies, viz. the case of the ‘black hole’ (the Netherlands and the case of ‘dark matter’(the US. Understanding the relation between the international investment position of a country and its balance of payments becomes more and more relevant as countries prepare for ageing of the population. Some countries explicitly aim at the creation of a national savings surplus in order to create a net international asset position. The consequences of the failure of such a policy are discussed in a concluding paragraph.

  12. The Process for the Formulation of the International Telehealth Position Statement for Occupational Therapy

    Science.gov (United States)

    JACOBS, KAREN; CASON, JANA; MCCULLOUGH, ANN

    2015-01-01

    The World Federation of Occupational Therapists (WFOT) consists of 84 member organizations representing over 420,000 occupational therapists internationally (WFOT, 2014). In 2014, WFOT published the WFOT Telehealth Position Statement on the use of telehealth in occupational therapy. The process for the formulation of the official document involved reviewing WFOT member organizations’ telehealth position statements and data collected from a survey sent to member organizations’ delegates in April 2014. Qualitative data from 39 countries yielded factors to consider in five key areas: licensure/registration requirements, the cost of technology, privacy and security, reimbursement/payment models, and other issues (e.g., need for collaboration/transfer of knowledge, client selection, provider competencies, standard of care). The WFOT Telehealth Position Statement addressed each of these areas. The collaborative effort resulting in the development of the WFOT Telehealth Position Statement serves as a model for other international organizations. PMID:27563380

  13. The Process for the Formulation of the International Telehealth Position Statement for Occupational Therapy

    Directory of Open Access Journals (Sweden)

    Karen Jacobs

    2015-07-01

    Full Text Available The World Federation of Occupational Therapists (WFOT consists of 84 member organizations representing over 420,000 occupational therapists internationally (WFOT, 2014.  In 2014, WFOT published the WFOT Telehealth Position Statement on the use of telehealth in occupational therapy. The process for the formulation of the official document involved reviewing WFOT member organizations’ telehealth position statements and data collected from a survey sent to member organizations’ delegates in April 2014.  Qualitative data from 39 countries yielded factors to consider in five key areas:  licensure/registration requirements, the cost of technology, privacy and security, reimbursement/payment models, and other issues (e.g., need for collaboration/transfer of knowledge, client selection, provider competencies, standard of care.  The WFOT Telehealth Position Statement addressed each of these areas.  The collaborative effort resulting in the development of the WFOT Telehealth Position Statement serves as a model for other international organizations.

  14. The Process for the Formulation of the International Telehealth Position Statement for Occupational Therapy.

    Science.gov (United States)

    Jacobs, Karen; Cason, Jana; McCullough, Ann

    2015-01-01

    The World Federation of Occupational Therapists (WFOT) consists of 84 member organizations representing over 420,000 occupational therapists internationally (WFOT, 2014). In 2014, WFOT published the WFOT Telehealth Position Statement on the use of telehealth in occupational therapy. The process for the formulation of the official document involved reviewing WFOT member organizations' telehealth position statements and data collected from a survey sent to member organizations' delegates in April 2014. Qualitative data from 39 countries yielded factors to consider in five key areas: licensure/registration requirements, the cost of technology, privacy and security, reimbursement/payment models, and other issues (e.g., need for collaboration/transfer of knowledge, client selection, provider competencies, standard of care). The WFOT Telehealth Position Statement addressed each of these areas. The collaborative effort resulting in the development of the WFOT Telehealth Position Statement serves as a model for other international organizations.

  15. Radiation protection - Monitoring of workers occupationally exposed to a risk of internal contamination with radioactive material

    International Nuclear Information System (INIS)

    2006-01-01

    In the course of employment, individuals might work with radioactive materials that, under certain circumstances, could be taken into the body. Protecting workers against risks of incorporated radionuclides requires the monitoring of potential intakes and/or the quantification of actual intakes and exposures. The selection of measures and programmes for this purpose requires decisions concerning methods, techniques, frequencies etc. for measurements and dose assessment. The criteria permitting the evaluation of the necessity of such a monitoring programme or for the selection of methods and frequencies of monitoring usually depend upon the legislation, the purpose of the radiation protection programme, the probabilities of potential radionuclide intakes, and the characteristics of the materials handled. This International Standard offers guidance for the decision whether a monitoring programme is required and how it should be designed. Its intention is to optimise the efforts for such a monitoring programme consistent with legal requirements and with the purpose of the radiation protection programme. Recommendations of international expert bodies and international experience with the practical application of these recommendations in radiation protection programmes have been considered in the development of this International Standard. Its application facilitates the exchanges of information between authorities, supervisory institutions and employers. The International Standard is not a substitute for legal requirements. In the International Standard, the word 'shall' is used to denote a requirement and no deviation is allowed. The word 'should' is used to denote a recommendation from which justified deviations are allowed. The word 'may' is used to denote permission

  16. International society of sports nutrition position stand: diets and body composition

    OpenAIRE

    Aragon, Alan A.; Schoenfeld, Brad J.; Wildman, Robert; Kleiner, Susan; VanDusseldorp, Trisha; Taylor, Lem; Earnest, Conrad P.; Arciero, Paul J.; Wilborn, Colin; Kalman, Douglas S.; Stout, Jeffrey R.; Willoughby, Darryn S.; Campbell, Bill; Arent, Shawn M.; Bannock, Laurent

    2017-01-01

    Position Statement: The International Society of Sports Nutrition (ISSN) bases the following position stand on a critical analysis of the literature regarding the effects of diet types (macronutrient composition; eating styles) and their influence on body composition. The ISSN has concluded the following. 1) There is a multitude of diet types and eating styles, whereby numerous subtypes fall under each major dietary archetype. 2) All body composition assessment methods have strengths and limi...

  17. A real-time applicator position monitoring system for gynecologic intracavitary brachytherapy

    Energy Technology Data Exchange (ETDEWEB)

    Xia, Junyi, E-mail: junyi-xia@uiowa.edu; Waldron, Timothy; Kim, Yusung [Department of Radiation Oncology, University of Iowa, Iowa City, Iowa 52242 (United States)

    2014-01-15

    Purpose: To develop a real-time applicator position monitoring system (RAPS) for intracavitary brachytherapy using an infrared camera and reflective markers. Methods: 3D image-guided brachytherapy requires high accuracy of applicator localization; however, applicator displacement can happen during patient transfer for imaging and treatment delivery. No continuous applicator position monitoring system is currently available. The RAPS system was developed for real-time applicator position monitoring without additional radiation dose to patients. It includes an infrared camera, reflective markers, an infrared illuminator, and image processing software. After reflective markers are firmly attached to the applicator and the patient body, applicator displacement can be measured by computing the relative change in distance between the markers. The reflective markers are magnetic resonance imaging (MRI) compatible, which is suitable for MRI-guided HDR brachytherapy paradigm. In our prototype, a Microsoft Kinect sensor with a resolution of 640 by 480 pixels is used as an infrared camera. A phantom study was carried out to compare RAPS' measurements with known displacements ranging from −15 to +15 mm. A reproducibility test was also conducted. Results: The RAPS can achieve 4 frames/s using a laptop with Intel{sup ®} Core™2 Duo processor. When the pixel size is 0.95 mm, the difference between RAPS' measurements and known shift values varied from 0 to 0.8 mm with the mean value of 0.1 mm and a standard deviation of 0.44 mm. The system reproducibility was within 0.6 mm after ten reposition trials. Conclusions: This work demonstrates the feasibility of a real-time infrared camera based gynecologic intracavitary brachytherapy applicator monitoring system. Less than 1 mm accuracy is achieved when using an off-the-shelf infrared camera.

  18. Deficits in error monitoring are associated with externalizing but not internalizing behaviors among children with a history of institutionalization.

    Science.gov (United States)

    Troller-Renfree, Sonya; Nelson, Charles A; Zeanah, Charles H; Fox, Nathan A

    2016-10-01

    Children raised in institutions are at increased risk of developing internalizing and externalizing problems. However, not all children raised in institutions develop psychopathology. Deficits in error monitoring may be one risk pathway for children with a history of institutionalization given that these skills are related to both internalizing and externalizing psychiatric disorders. Error monitoring and the neural circuitry that supports it have a protracted developmental time course and are highly susceptible to the effects of adversity. As such, they may play an important moderating role between a history of institutional rearing and subsequent psychopathology. We investigated the impact of psychosocial deprivation on behavioral and neural responses (event-related potentials: ERPs) to a Flanker task assessing error monitoring and the relations between these measures and psychopathology for 12-year-old children in the Bucharest Early Intervention Project (BEIP). The BEIP involves two groups of institutionalized children randomly assigned in infancy to receive either a foster care intervention (FCG) or care as usual (CAUG). Children who experienced institutional care, particularly those in the CAUG, showed perturbed behavioral performance and ERPs on the Flanker task. Additionally, an ERP measure of error monitoring [error-related negativity (ERN)] moderated the relations between time spent in institutions and externalizing and ADHD behaviors. When the amplitude of the ERN was smaller, time spent in institutional care was positively related to ADHD and externalizing behaviors, whereas time spent in institutions was unrelated to externalizing problems when children evidenced a larger ERN. Neural correlates of error monitoring did not moderate the relations between time spent in institutionalized care and internalizing behaviors. Exposure to institutional care early in life may affect brain circuitry associated with error monitoring. Perturbations in this neural

  19. Marketing Management: Monitoring the International Environment Factors Using Global Maps

    Directory of Open Access Journals (Sweden)

    Štěpán Kala

    2015-01-01

    Full Text Available The article discusses the issue of the global marketing environment in line with the factors determining its external conditions. The aim is to specify the marketing-environment indicators in the international context and interpret the use of geographical maps illustratively documenting the differences of particular parameters in various parts of the global market. The research-results help update the theoretical framework of global environment factors. These data are also important for practice. Many enterprises consider the question of optimising their sources and directing their goals towards the opportunities available thanks to global markets. The global environment mapping is thereby an important basis for the marketing activities whose implementation across national boundaries is going to be mainly influenced by peculiarities of the environment involving foreign markets and their changes.

  20. Noble gas atmospheric monitoring for international safeguards at reprocessing plants

    International Nuclear Information System (INIS)

    Nakhleh, C.W.; Poths, J.; Stanbro, W.D.; Perry, R.T. Jr.; Wilson, W.B.; Fearey, B.L.

    1997-01-01

    The use of environmental sampling is a major component of the improvements of International Atomic Energy Agency safeguards being carried out under Program 93+2. Nonradioactive noble gas isotopic measurements in the effluent stream of large reprocessing facilities may provide useful confirmatory information on the burnup and reactor type of the spent fuel undergoing reprocessing. The authors have taken and analyzed stack samples at an operating facility. The data show clear fission signals. The authors are currently applying a maximum-likelihood estimation procedure to determine the fuel burnup from these data. They anticipate that the general features involved in the table noble gas problem--selection of appropriate signals, measurement of those signals under realistic conditions, and inverse calculation of parameters of interest from the environmental data--will be present in all environmental sampling problems. These methods should therefore be widely applicable

  1. International health research monitoring: exploring a scientific and a cooperative approach using participatory action research.

    Science.gov (United States)

    Chantler, Tracey; Cheah, Phaik Yeong; Miiro, George; Hantrakum, Viriya; Nanvubya, Annet; Ayuo, Elizabeth; Kivaya, Esther; Kidola, Jeremiah; Kaleebu, Pontiano; Parker, Michael; Njuguna, Patricia; Ashley, Elizabeth; Guerin, Philippe J; Lang, Trudie

    2014-02-17

    To evaluate and determine the value of monitoring models developed by the Mahidol Oxford Tropical Research Unit and the East African Consortium for Clinical Research, consider how this can be measured and explore monitors' and investigators' experiences of and views about the nature, purpose and practice of monitoring. A case study approach was used within the context of participatory action research because one of the aims was to guide and improve practice. 34 interviews, five focus groups and observations of monitoring practice were conducted. Fieldwork occurred in the places where the monitoring models are coordinated and applied in Thailand, Cambodia, Uganda and Kenya. Participants included those coordinating the monitoring schemes, monitors, senior investigators and research staff. Transcribed textual data from field notes, interviews and focus groups was imported into a qualitative data software program (NVIVO V. 10) and analysed inductively and thematically by a qualitative researcher. The initial coding framework was reviewed internally and two main categories emerged from the subsequent interrogation of the data. The categories that were identified related to the conceptual framing and nature of monitoring, and the practice of monitoring, including relational factors. Particular emphasis was given to the value of a scientific and cooperative style of monitoring as a means of enhancing data quality, trust and transparency. In terms of practice the primary purpose of monitoring was defined as improving the conduct of health research and increasing the capacity of researchers and trial sites. The models studied utilise internal and network wide expertise to improve the ethics and quality of clinical research. They demonstrate how monitoring can be a scientific and constructive exercise rather than a threatening process. The value of cooperative relations needs to be given more emphasis in monitoring activities, which seek to ensure that research protects

  2. Assessment of HIV-positive in-patients using the International ...

    African Journals Online (AJOL)

    Assessment of HIV-positive in-patients using the International Classification of Functioning, Disability and Health (ICF) at Chris Hani Baragwanath Hospital, ... may serve as a baseline for developing appropriate and context-sensitive rehabilitation interventions and management strategies for people living with HIV or AIDS.

  3. Physical Activity and Psychological Benefits. International Society of Sport Psychology Position Statement.

    Science.gov (United States)

    Physician and Sportsmedicine, 1992

    1992-01-01

    International Society of Sport Psychology clarifies the psychological benefits of physical activity, noting the positive relationship between physical activity level and mental health. Exercise can reduce anxiety, decrease depression levels, reduce neuroticism and anxiety, reduce stress, and have beneficial emotional effects for both sexes across…

  4. Individual monitoring program for internal contamination by inhaled uranium

    International Nuclear Information System (INIS)

    Vazquez, C.; Chapel, M.L.; Saenz Gancedo, R.

    1988-01-01

    The metabolic behaviour of inhaled uranium is studied. Using a particular analytical method applied to the models and dose assessment methods recommended by ICRP, the organ committed equivalent dose and effective equivalent dose are calculated. The exact ALI and DAC are derived from there. In the paper, the influence that various parameters have on those results are considered for the specific case of a particular nuclear element fabrication factory. Different AMAD and solubility type of inhaled material are specially analyzed. The results show the paramount importance of some of these parameters on the secondary and derived dose limits. Relationships between the real intake, as a fraction of ALI, and the lung retention or urine excretion are shown for different cases and intake forms hypothesis. Minimum detectable intakes with the available experimental techniques are then established. The results shown in the papel are a useful tool to help on the decision on the type and frequency of the individual monitoring techniques to be established in different circumstances. (Author)

  5. Internal contamination monitoring in the German Democratic Republic. Report on the experience of twelve years

    International Nuclear Information System (INIS)

    Poulheim, K.F.; Arndt, D.; Klucke, H.; Loessner, V.; Scheler, R.; Schlueter, W.

    1979-01-01

    After a short explanation of the organization for monitoring internal contamination in the German Democratic Republic, an estimation of working places is presented. Criteria are given for selecting persons to be subjected to a direct or indirect measurement of internal contamination. While, in the National Board of Nuclear Safety and Radiation Protection, examinations for internal contamination had formerly been made by groups of persons selected on the basis of special aspects of their work, such monitoring has for several years had a systematic character. From among all persons exposed to unsealed radionuclides, a group of persons to be subjected to monitoring has been established. The selection was made by calculating on the basis of model concepts and topical working-place data an individual incorporation risk which is specific for a given working area. The central and peripheral measuring devices of the monitoring system are presented. The central, very effective devices consist of a pair of whole-body counters. The methods of measuring internal contamination directly are supplemented by methods for measuring biological samples and exhaled breath. The monitoring system is complemented by smaller peripheral devices. Monitoring results obtained over a period of about 12 years are discussed. (author)

  6. Official Positions for FRAX® clinical regarding international differences from Joint Official Positions Development Conference of the International Society for Clinical Densitometry and International Osteoporosis Foundation on FRAX®.

    Science.gov (United States)

    Cauley, Jane A; El-Hajj Fuleihan, Ghada; Arabi, Asma; Fujiwara, Saeko; Ragi-Eis, Sergio; Calderon, Andrew; Chionh, Siok Bee; Chen, Zhao; Curtis, Jeffrey R; Danielson, Michelle E; Hanley, David A; Kroger, Heikki; Kung, Annie W C; Lesnyak, Olga; Nieves, Jeri; Pluskiewicz, Wojciech; El Rassi, Rola; Silverman, Stuart; Schott, Anne-Marie; Rizzoli, Rene; Luckey, Marjorie

    2011-01-01

    Osteoporosis is a serious worldwide epidemic. Increased risk of fractures is the hallmark of the disease and is associated with increased morbidity, mortality and economic burden. FRAX® is a web-based tool developed by the Sheffield WHO Collaborating Center team, that integrates clinical risk factors, femoral neck BMD, country specific mortality and fracture data and calculates the 10 year fracture probability in order to help health care professionals identify patients who need treatment. However, only 31 countries have a FRAX® calculator at the time paper was accepted for publication. In the absence of a FRAX® model for a particular country, it has been suggested to use a surrogate country for which the epidemiology of osteoporosis most closely approximates the index country. More specific recommendations for clinicians in these countries are not available. In North America, concerns have also been raised regarding the assumptions used to construct the US ethnic specific FRAX® calculators with respect to the correction factors applied to derive fracture probabilities in Blacks, Asians and Hispanics in comparison to Whites. In addition, questions were raised about calculating fracture risk in other ethnic groups e.g., Native Americans and First Canadians. In order to provide additional guidance to clinicians, a FRAX® International Task Force was formed to address specific questions raised by physicians in countries without FRAX® calculators and seeking to integrate FRAX® into their clinical practice. The main questions that the task force tried to answer were the following: The Task Force members conducted appropriate literature reviews and developed preliminary statements that were discussed and graded by a panel of experts at the ISCD-IOF joint conference. The statements approved by the panel of experts are discussed in the current paper. Copyright © 2011. Published by Elsevier Inc.

  7. A novel straightness measurement system applied to the position monitoring of large Particle Physics Detectors

    CERN Document Server

    Goudard, R; Ribeiro, R; Klumb, F

    1999-01-01

    The Compact Muon Solenoid experiment, CMS, is one of the two general purpose experiments foreseen to operate at the Large Hadron Collider, LHC, at CERN, the European Laboratory for Particle Physics. The experiment aims to study very high energy collisions of proton beams. Investigation of the most fundamental properties of matter, in particular the study of the nature of the electroweak symmetry breaking and the origin of mass, is the experiment scope. The central Tracking System, a six meter long cylinder with 2.4 m diameter, will play a major role in all physics searches of the CMS experiment. Its performance depends upon the intrinsic detector performance, on the stability of the supporting structure and on the overall survey, alignment and position monitoring system. The proposed position monitoring system is based on a novel lens-less laser straightness measurement method able to detect deviations from a nominal position of all structural elements of the Central Tracking system. It is based on the recipr...

  8. Wireless online position monitoring of manual valve types for plant configuration management in nuclear power plants

    International Nuclear Information System (INIS)

    Agarwal, Vivek; Buttles, John W.; Beaty, Lawrence H.; Naser, Joseph; Hallbert, Bruce P.

    2016-01-01

    In the current competitive energy market, the nuclear industry is committed to lower the operations and maintenance cost; increase productivity and efficiency while maintaining safe and reliable operation. The present operating model of nuclear power plants is dependent on large technical staffs that put the nuclear industry at long-term economic disadvantage. Technology can play a key role in nuclear power plant configuration management in offsetting labor costs by automating manually performed plant activities. The technology being developed, tested, and demonstrated in this paper will enable the continued safe operation of today’s fleet of light water reactors by providing the technical means to monitor components in plants today that are only routinely monitored through manual activities. The wireless enabled valve position indicators that are the subject of this paper are able to provide a valid position indication available continuously, rather than only periodically. As a result, a real-time (online) availability of valve positions using an affordable technologies are vital to plant configuration when compared with long-term labor rates, and provide information that can be used for a variety of plant engineering, maintenance, and management applications.

  9. EVALUATION OF POSTGRADUATES STRICTO SENSU: MONITORING POLICY FOR INTERNATIONAL GRADUATES

    Directory of Open Access Journals (Sweden)

    Wilma Terezinha Anselmo Lima

    Full Text Available Objective: Search for references in relationship to international alumni on the website of the postgraduate programs of all postgraduate courses at Ribeirão Preto Medical School - FMRP. Methods: Verify with more attention to the ones with 5, 6 and 7 notes, and also the same search on the website of courses with notes 5, 6 and 7 of CAPES - Medicine III. Results: Of the 22 programs of FMRP only three had any information on the site about the destiny of the postgraduates; they were: Surgical Clinics, Genetics, and Basic and Applied Immunology. Programs in the area of Medicine III, notes 5, 6 and 7, only Ophthalmology and Visual Programs and Translational Sciences Surgery, both of UNIFESP, presented such information. Conclusion: It is urgent: to create project and funding evaluation mechanisms that are approved by different sources; to stimulate more efficient controls in relation to teachers and their students who participate in these projects; and to stimulate the interaction of teachers and students with the institution and the program.

  10. Noninvasive intracranial pressure monitoring via optic nerve sheath diameter for robotic surgery in steep Trendelenburg position

    Directory of Open Access Journals (Sweden)

    Shagun Bhatia Shah

    2015-01-01

    Full Text Available Background: Recent reports of increased intracranial pressure (ICP due to steep Trendelenburg (ST position causing neurological deterioration, decreased regional cerebral oxygen saturation and postoperative visual loss after robotic urological and gynecological surgeries led us to consider a simple technique of ICP monitoring. Ours is one of the first instances reported of quantitative noninvasive measurement of increase in ICP with ST position by serial measurement of binocular optic nerve sheath diameter (ONSD in patients undergoing robot assisted urological and gynecological oncosurgery. We tested whether ONSD values rose to above the upper limits of normal and for what length of time they remained elevated. Materials and Methods: Prospective, randomized, interventional, parallel group, active control study conducted on 252 American Society of Anesthesiologists I and II patients. ONSD was measured using 7.5 MHz linear ultrasound probe in supine and Trendelenburg positions. Statistics: Student′s t-test to compare the inter-group mean ONSD and the repetitive t-test for intra-group analysis. Result: Comparison of the mean ONSD values of both groups yielded a 2-tailed significance P <0.01 at all compared time points intra- and post-operatively. In Group-O (open surgery; supine position, the baseline mean bilateral ONSD was 4.36 mm, which did not show any statistically significant change throughout open surgery and postoperative period. On de-docking the robot, 6.2 mm was the mean ONSD value in Group-R (robotic group while 4.3 mm was the corresponding value in control Group-O. Conclusion: ONSD evaluation is a simple, quick, safe, readily available, reliable, cost effective, noninvasive, potential standard of care for screening and monitoring of patients undergoing robotic surgery in ST position.

  11. ACCELERATORS: Design and simulation of a beam position monitor for the high current proton linac

    Science.gov (United States)

    Ruan, Yu-Fang; Xu, Tao-Guang; Fu, Shi-Nian

    2009-03-01

    In this paper, the 2-D electrostatic field software, POISSON, is used to calculate the characteristic impedance of a BPM (beam position monitor) for a high current proton linac. Furthermore, the time-domain 3-D module of MAFIA with a beam microbunch at a varying offset from the axis is used to compute the induced voltage on the electrodes as a function of time. Finally, the effect of low β beams on the induced voltage, the sensitivity and the signal dynamic range of the BPM are discussed.

  12. Beam position monitoring system for the proposed asymmetric B Factory at SLAC

    International Nuclear Information System (INIS)

    Pellegrin, J.L.

    1992-10-01

    The beam position monitor system of the B Factory is drastically different from the actual PEP system. We present a description of the new configuration and list the features which have been adopted to make this system a highly reliable diagnostic tool. An electrode geometry is suggested, based on the maximum-acceptable power extracted from the beam, and the measurement resolution is estimated by assuming some practical bandwidth and the noise level. Finally, an estimate of the system precision is made by adding up what is expected to be the most significant systematic errors

  13. A contactless positioning system for monitoring discontinuities in three dimensions with geological and geotechnical applications

    Czech Academy of Sciences Publication Activity Database

    Rinaldi-Montes, N.; Rowberry, Matthew David; Frontera, C.; Baroň, I.; Garcés, G.; Blahůt, Jan; Pérez-López, R.; Pennos, C.; Martí, Xavier

    2017-01-01

    Roč. 88, č. 7 (2017), č. článku 074501. ISSN 0034-6748 R&D Projects: GA MŠk LM2010008 Institutional support: RVO:67985891 ; RVO:68378271 Keywords : mechanical discontinuities * contactless positioning system * magnetoresistive sensing * geotechnical engineering * structural health monitoring Subject RIV: JB - Sensors, Measurment, Regulation; BM - Solid Matter Physics ; Magnetism (FZU-D) OBOR OECD: Environmental and geological engineering , geotechnics; Condensed matter physics (including formerly solid state physics, supercond.) (FZU-D) Impact factor: 1.515, year: 2016

  14. Self-generation and positivity effects following transcranial random noise stimulation in medial prefrontal cortex: A reality monitoring task in older adults.

    Science.gov (United States)

    Mammarella, Nicola; Di Domenico, Alberto; Palumbo, Rocco; Fairfield, Beth

    2017-06-01

    Activation of medial Prefrontal Cortex (mPFC) has been typically found during reality monitoring tasks (i.e., distinguishing between internal self-generated vs external information). No study, however, has yet investigated whether transcranial Random Noise Stimulation (tRNS) over the mPFC leads to a reduction in reality-monitoring misattributions in aging. In particular, stimulating mPFC should increase the number of cognitive operations engaged while encoding and this distinctive information may help older adults to discriminate between internal and external sources better. In addition, given that older adults are more sensitive to positively-charged information compared to younger adults and that mPFC is typically recruited during encoding of positive stimuli with reference to themselves, activation of mPFC should further sustain source retrieval in older adults. In this double-blind, sham-controlled study, we examined whether tRNS over the mPFC of healthy younger and older adults during encoding enhances subsequent reality monitoring for seen versus imagined emotionally-charged words. Our findings show that tRNS enhances reality monitoring for positively-charged imagined words in the older adult group alone, highlighting the role that mPFC plays in their memory for positive information. In line with the control-based account of positivity effects, our results add evidence about the neurocognitive processes involved in reality monitoring when older adults face emotionally-charged events. Copyright © 2016 Elsevier Ltd. All rights reserved.

  15. EVALUATION OF POSTGRADUATES STRICTO SENSU: MONITORING POLICY FOR INTERNATIONAL GRADUATES.

    Science.gov (United States)

    Lima, Wilma Terezinha Anselmo

    2015-01-01

    Search for references in relationship to international alumni on the website of the postgraduate programs of all postgraduate courses at Ribeirão Preto Medical School - FMRP. Verify with more attention to the ones with 5, 6 and 7 notes, and also the same search on the website of courses with notes 5, 6 and 7 of CAPES - Medicine III. Of the 22 programs of FMRP only three had any information on the site about the destiny of the postgraduates; they were: Surgical Clinics, Genetics, and Basic and Applied Immunology. Programs in the area of ​​Medicine III, notes 5, 6 and 7, only Ophthalmology and Visual Programs and Translational Sciences Surgery, both of UNIFESP, presented such information. It is urgent: to create project and funding evaluation mechanisms that are approved by different sources; to stimulate more efficient controls in relation to teachers and their students who participate in these projects; and to stimulate the interaction of teachers and students with the institution and the program. Verificar a existência de referências aos egressos internacionais nos sites dos programas de pós-graduação de todos os cursos de pós-graduação da Faculdade de Medicina de Ribeirão Preto - FMRP. Verificar com mais atenção aos cursos notas 5, 6 e 7, e também a mesma busca nos sites dos cursos com notas 5, 6 e 7 da Medicina III da CAPES. Dos 22 programas da FMRP apenas três tinham no site alguma informação sobre o destino dos egressos, foram eles: Clínica Cirúrgica, Genética e Imunologia Básica e Aplicada. Dos programas da área de Medicina III, notas 5, 6 e 7 apenas os programas de Oftalmologia e Ciências Visuais e Cirurgia Translacional, ambos da UNIFESP, apresentavam informações sobre o destino dos seus egressos. É urgente criar mecanismos de avaliação para os projetos de incentivo e fomento à pesquisa dos diferentes órgãos; estimular controles mais eficientes e atualizados em relação aos docentes e seus respectivos discentes que

  16. International issues: Obtaining an adult neurology residency position in the United States: an overview.

    Science.gov (United States)

    Jordan, Justin T; Sellner, Johann; Struhal, Walter; Schneider, Logan; Mayans, David

    2014-04-08

    Around the world, there are marked differences in neurology training, including training duration and degree of specialization. In the United States, adult neurology residency is composed of 1 year of internal medicine training (preliminary year) and 3 years of neurology-specific training. Child neurology, which is not the focus of this article, is 2 years of pediatrics and 3 years of neurology training. The route to adult neurology residency training in the United States is standardized and is similar to most other US specialties. Whereas US medical graduates often receive stepwise guidance from their medical school regarding application for residency training, international graduates often enter this complex process with little or no such assistance. Despite this discrepancy, about 10%-15% of residency positions in the United States are filled by international medical graduates.(1,2) In adult neurology specifically, 35% of matched positions were filled by international graduates in 2013, 75% of whom were not US citizens.(1) In an effort to provide a preliminary understanding of the application process and related terminology (table 1) and thereby encourage international residency applicants, we describe the steps necessary to apply for neurology residency in the United States.

  17. Performance of the Lancelot Beam Position Monitor at the Diamond Light Source

    Science.gov (United States)

    Chagani, H.; Garcia-Nathan, T. B.; Jiang, C.; Kachatkou, A.; Marchal, J.; Omar, D.; Tartoni, N.; van Silfhout, R. G.; Williams, S.

    2017-12-01

    The Lancelot beam position and profile monitor records the scattered radiation off a thin, low-density foil, which passes through a pinhole perpendicular to the path of the beam and is detected by a Medipix3RX sensor. This arrangement does not expose the detector to the direct beam at synchrotrons and results in a negligible drop in flux downstream of the module. It allows for magnified images of the beam to be acquired in real time with high signal-to-noise ratios, enabling measurements of tiny displacements in the position of the centroid of approximately 1 μm. It also provides a means for independently measuring the photon energy of the incident monoenergetic photon beam. A constant frame rate of up to 245 Hz is achieved. The results of measurements with two Lancelot detectors installed in different environments at the Diamond Light Source are presented and their performance is discussed.

  18. High-Precision Resonant Cavity Beam Position, Emittance and Third-Moment Monitors

    CERN Document Server

    Barov, Nikolai; Miller, Roger H; Nantista, Christopher D; Weidemann, A W

    2005-01-01

    Linear colliders and FEL facilities need fast, nondestructive beam position and profile monitors to facilitate machine tune-up, and for use with feedback control. FAR-TECH, Inc. is developing a resonant cavity diagnostic to simultaneously measure the dipole, quadrupole and sextupole moments of the beam distribution. Measurements of dipole and quadrupole moments at multiple locations yield information about beam orbit and emittance. The sextupole moment can reveal information about beam asymmetry which is useful in diagnosing beam tail deflections caused by short range dipole wakefields. In addition to the resonance enhancement of a single-cell cavity, use of a multi-cell standign-wave structure further enhances signal strength and improves the resolution of the device. An estimated rms beam size resolution is sub micro-meters and beam position is sub nano-meter.

  19. Model-independent analysis of the Fermilab Tevatron turn-by-turn beam position monitor measurements

    Energy Technology Data Exchange (ETDEWEB)

    Petrenko, A.V.; /Novosibirsk, IYF; Valishev, A.A.; Lebedev, V.A.; /Fermilab

    2011-09-01

    Coherent transverse beam oscillations in the Tevatron were analyzed with the model-independent analysis (MIA) technique. This allowed one to obtain the model-independent values of coupled betatron amplitudes, phase advances, and dispersion function around the ring from a single dipole kick measurement. In order to solve the MIA mode mixing problem which limits the accuracy of determination of the optical functions, we have developed a new technique of rotational MIA mode untangling. The basic idea is to treat each beam position monitor (BPM) as two BPMs separated in a ring by exactly one turn. This leads to a simple criterion of MIA mode separation: the betatron phase advance between any BPM and its counterpart shifted by one turn should be equal to the betatron tune and therefore should not depend on the BPM position in the ring. Furthermore, we describe a MIA-based technique to locate vibrating magnets in a storage ring.

  20. Prototyping of beam position monitor for medium energy beam transport section of RAON heavy ion accelerator

    Energy Technology Data Exchange (ETDEWEB)

    Jang, Hyojae, E-mail: lkcom@ibs.re.kr; Jin, Hyunchang; Jang, Ji-Ho; Hong, In-Seok [Rare Isotope Science Project, Institute for Basic Science, Daejeon (Korea, Republic of)

    2016-02-15

    A heavy ion accelerator, RAON is going to be built by Rare Isotope Science Project in Korea. Its target is to accelerate various stable ions such as uranium, proton, and xenon from electron cyclotron resonance ion source and some rare isotopes from isotope separation on-line. The beam shaping, charge selection, and modulation should be applied to the ions from these ion sources because RAON adopts a superconducting linear accelerator structure for beam acceleration. For such treatment, low energy beam transport, radio frequency quadrupole, and medium energy beam transport (MEBT) will be installed in injector part of RAON accelerator. Recently, development of a prototype of stripline beam position monitor (BPM) to measure the position of ion beams in MEBT section is under way. In this presentation, design of stripline, electromagnetic (EM) simulation results, and RF measurement test results obtained from the prototyped BPM will be described.

  1. Anti-Corruption Measures: Persistent Problems Exist in Monitoring Bulk Cash Flows at Kabul International Airport

    Science.gov (United States)

    2012-12-11

    SIGAR SP-13-1 Anti- Corruption / Currency Movement at KBL Special Inspector General for Afghanistan Reconstruction SIGAR ANTI... CORRUPTION MEASURES: PERSISTENT PROBLEMS EXIST IN MONITORING BULK CASH FLOWS AT KABUL INTERNATIONAL AIRPORT This product was completed under SIGAR’s...REPORT TYPE 3. DATES COVERED 00-00-2012 to 00-00-2012 4. TITLE AND SUBTITLE Anti- Corruption Measures: Persistent Problems Exist in Monitoring Bulk

  2. A Demonstration of GPS Landslide Monitoring Using Online Positioning User Service (OPUS)

    Science.gov (United States)

    Wang, G.

    2011-12-01

    Global Positioning System (GPS) technologies have been frequently applied to landslide study, both as a complement, and as an alternative to conventional surveying methods. However, most applications of GPS for landslide monitoring have been limited to the academic community for research purposes. High-accuracy GPS has not been widely equipped in geotechnical companies and used by technicians. The main issue that limits the applications of GPS in the practice of high-accuracy landslide monitoring is the complexity of GPS data processing. This study demonstrated an approach using the Online Positioning User Service (OPUS) (http://www.ngs.noaa.gov/OPUS) provided by the National Geodetic Survey (NGS) of National Oceanic and Atmospheric Administration (NOAA) to process GPS data and conduct long-term landslide monitoring in the Puerto Rico and Virgin Islands Region. Continuous GPS data collected at a creeping landslide site during two years were used to evaluate different scenarios for landslide surveying: continuous or campaign, long duration or short duration, morning or afternoon (different weather conditions). OPUS uses Continuously Operating Reference Station (CORS) managed by NGS (http://www.ngs.noaa.giv/CORS/) as references and user data as a rover to solve a position. There are 19 CORS permanent GPS stations in the Puerto Rico and Virgin Islands region. The dense GPS network provides a precise and reliable reference frame for subcentimeter-accuracy landslide monitoring in this region. Our criterion for the accuracy was the root-mean-square (RMS) of OPUS solutions over a 2-year period with respect to true landslide displacement time series overt the same period. The true landslide displacements were derived from a single-baseline (130 m) GPS processing by using 24-hour continuous data. If continuous GPS surveying is performed in the field, then OPUS static processing can provide 0.6 cm horizontal and 1.1 cm vertical precision with few outliers. If repeated

  3. Beam feasibility study of a collimator with in-jaw beam position monitors

    Energy Technology Data Exchange (ETDEWEB)

    Wollmann, Daniel, E-mail: daniel.wollmann@cern.ch [CERN, Geneva (Switzerland); Nosych, Andriy A. [CERN, Geneva (Switzerland); Cockcroft Institute, Daresbury (United Kingdom); The University of Liverpool, Liverpool (United Kingdom); Valentino, Gianluca; Aberle, Oliver; Aßmann, Ralph W.; Bertarelli, Alessandro; Boccard, Christian; Bruce, Roderik; Burkart, Florian; Calvo, Eva; Cauchi, Marija; Dallocchio, Alessandro; Deboy, Daniel; Gasior, Marek; Jones, Rhodri; Kain, Verena; Lari, Luisella; Redaelli, Stefano; Rossi, Adriana [CERN, Geneva (Switzerland)

    2014-12-21

    At present, the beam-based alignment of the LHC collimators is performed by touching the beam halo with both jaws of each collimator. This method requires dedicated fills at low intensities that are done infrequently and makes this procedure time consuming. This limits the operational flexibility, in particular in the case of changes of optics and orbit configuration in the experimental regions. The performance of the LHC collimation system relies on the machine reproducibility and regular loss maps to validate the settings of the collimator jaws. To overcome these limitations and to allow a continuous monitoring of the beam position at the collimators, a design with jaw-integrated Beam Position Monitors (BPMs) was proposed and successfully tested with a prototype (mock-up) collimator in the CERN SPS. Extensive beam experiments allowed to determine the achievable accuracy of the jaw alignment for single and multi-turn operation. In this paper, the results of these experiments are discussed. The non-linear response of the BPMs is compared to the predictions from electromagnetic simulations. Finally, the measured alignment accuracy is compared to the one achieved with the present collimators in the LHC.

  4. Beam feasibility study of a collimator with in-jaw beam position monitors

    Science.gov (United States)

    Wollmann, Daniel; Nosych, Andriy A.; Valentino, Gianluca; Aberle, Oliver; Aßmann, Ralph W.; Bertarelli, Alessandro; Boccard, Christian; Bruce, Roderik; Burkart, Florian; Calvo, Eva; Cauchi, Marija; Dallocchio, Alessandro; Deboy, Daniel; Gasior, Marek; Jones, Rhodri; Kain, Verena; Lari, Luisella; Redaelli, Stefano; Rossi, Adriana

    2014-12-01

    At present, the beam-based alignment of the LHC collimators is performed by touching the beam halo with both jaws of each collimator. This method requires dedicated fills at low intensities that are done infrequently and makes this procedure time consuming. This limits the operational flexibility, in particular in the case of changes of optics and orbit configuration in the experimental regions. The performance of the LHC collimation system relies on the machine reproducibility and regular loss maps to validate the settings of the collimator jaws. To overcome these limitations and to allow a continuous monitoring of the beam position at the collimators, a design with jaw-integrated Beam Position Monitors (BPMs) was proposed and successfully tested with a prototype (mock-up) collimator in the CERN SPS. Extensive beam experiments allowed to determine the achievable accuracy of the jaw alignment for single and multi-turn operation. In this paper, the results of these experiments are discussed. The non-linear response of the BPMs is compared to the predictions from electromagnetic simulations. Finally, the measured alignment accuracy is compared to the one achieved with the present collimators in the LHC.

  5. The spatial coherence structure of infrasonic waves: analysis of data from International Monitoring System arrays

    Science.gov (United States)

    Green, David N.

    2015-04-01

    The spatial coherence structure of 30 infrasound array detections, with source-to-receiver ranges of 25-6500 km, has been measured within the 0.25-1 Hz passband. The data were recorded at International Monitoring System (IMS) microbarograph arrays with apertures of between 1 and 4 km. Such array detections are of interest for Comprehensive Nuclear-Test-Ban Treaty monitoring. The majority of array detections (e.g. 80 per cent of recordings in the third-octave passband centred on 0.63 Hz) exhibit spatial coherence loss anisotropy that is consistent with previous lower frequency atmospheric acoustic studies; coherence loss is more rapid perpendicular to the acoustic propagation direction than parallel to it. The thirty array detections display significant interdetection variation in the magnitude of spatial coherence loss. The measurements can be explained by the simultaneous arrival of wave fronts at the recording array with angular beamwidths of between 0.4 and 7° and velocity bandwidths of between 2 and 40 m s-1. There is a statistically significant positive correlation between source-to-receiver range and the magnitude of coherence loss. Acoustic multipathing generated by interactions with fine-scale wind and temperature gradients along stratospheric propagation paths is qualitatively consistent with the observations. In addition, the study indicates that to isolate coherence loss generated by propagation effects, analysis of signals exhibiting high signal-to-noise ratios (SNR) is required (SNR2 > 11 in this study). The rapid temporal variations in infrasonic noise observed in recordings at IMS arrays indicates that correcting measured coherence values for the effect of noise, using pre-signal estimates of noise power, is ineffective.

  6. Optimization of four-button beam position monitor configuration for small-gap vacuum chambers

    Energy Technology Data Exchange (ETDEWEB)

    Kim, S.H.

    1998-03-27

    Induced charges on a four-button beam position monitor (BPM) system attached on a beam chamber of narrow rectangular cross sections are calculated as a 2-D electrostatic problem of image charges. The calculation shows that for a narrow chamber of width/height (2w/2h) {much_gt} 1, over 90% of the induced charges are distributed within a distance of 2h from the charged beam position in the direction of the chamber width. Therefore, a four-button system with a button diameter of (2--2.5)h and no button offset from the beam position is the most efficient configuration. The four-button BPMs used for 8-mm and 5-mm chambers in the APS have relatively low sensitivities because the button locations are outside the range where the induced charge densities are low and the button diameters are less than 2h. Using derived formulae, button sensitivities and beam position coefficients are calculated for the buttons of the most efficient case and of the 8-mm and 5-mm chambers. The formulae may be used to validate the method of computer modeling for BPM buttons on a beam chamber of an arbitrary cross section.

  7. The European Union Building Peace Near and Afar: Monitoring the Implementation of International Peace Agreements

    Directory of Open Access Journals (Sweden)

    Máire Braniff

    2013-11-01

    Full Text Available The European Union’s (EU support and contribution to international peace and security continues to develop with involvement in the Balkans, South Caucasus, Africa, Middle East and South Asia (Council of the European Union 2005. Within the broad range of civilian and military interventions under the Common Security and Defence policy (CSDP there have been two monitoring missions that have emerged from peace agreements, in Aceh (2005-2006 and in Georgia (2008 to date. This article maps the evolution EU’s role in international peace building by focusing on how this role is increasingly constructed by the scope of monitoring missions which it has embarked upon outside of its borders. A thematic analysis of literature is used to explore how the EU’s monitoring role has evolved regarding the different degrees of intervention, time-frame and size of the monitoring mission which have resulted in a multi-level impact regarding societal transition. The article finds that political will, shadows of past and future missions and intergovernmental concerns dominates how the EU’s monitoring missions unfurl, affecting the practice of monitors and other EU actors in local conflict settings and contemplates scenarios for future monitoring missions.

  8. Upgrading to lead firm position via international acquisition: learning from the global biomass power plant industry

    DEFF Research Database (Denmark)

    Hansen, Ulrich Elmer; Fold, Niels; Hansen, Teis

    2016-01-01

    This article examines the case of a Chinese firm that has upgraded to lead firm position in the global biomass power plant industry mainly through acquisitions of technological frontier firms in Denmark. Sustaining the lead firm position was, however, challenged by difficulties in developing...... innovative capability. Drawing on the literature on (i) firm-level technological capability and (ii) knowledge transfer in international acquisitions, we explain the reasons for insufficient innovative capability building. Based on these empirical findings, we suggest maintaining the existing upgrading...

  9. What Factors Coordinate the Optimal Position of a Single Monitoring Well Down Gradient of a Hazardous Site?

    Science.gov (United States)

    Bode, F.; Nowak, W.

    2013-12-01

    Drinking-water well catchments include many sources for potential contaminations like gas stations, roads, or fields used for agriculture. Additionally, there are many contaminated sites that need to be monitored inside and outside drinking water catchments. Finding optimal positions of monitoring wells for such purposes is challenging because there are various parameters (and their uncertainties) that influence the reliability and optimality of a suggested monitoring location. For example, there may be uncertainty in the exact position of the contamination, in the source volume, in the direction of the velocity field which can vary in angle and absolute value, and in other parameters that describe, e.g., dispersion and decay. Many national regulations and UN guidelines suggest monitoring as measure of risk control, but make no statements how to asses or design monitoring under the fact of uncertainty. To obtain optimal positions of monitoring wells, a large body of recent studies uses formal optimization approaches. Our goal is to obtain a better system understanding at a fundamental process level for the one-on-one situation of a single monitoring well for a single monitoring target. This knowledge can be used for a better understanding of the optimization results in complex situations, and also to better guide and restrict optimization procedures by newly obtained export knowledge. In order to obtain fundamental statements regardless of specific simulation settings, we use an analytical model based on the 2D steady-state advection-dispersion equation to predict contaminant transport from the monitoring target. Monte Carlo simulation techniques are applied to represent parametric uncertainty. Thus, we can obtain maps of contaminant detection probability for all possible placements of the monitoring well. The optimal position is defined by the highest detection probability. First findings show that uncertainty in the spill location pushes the optimal monitoring

  10. Web system for dosimetric data management of internal monitoring programme at IPEN

    International Nuclear Information System (INIS)

    Lima, Vanesa R. de; Rodriguez Junior, Orlando; Todo, Alberto S.

    2008-01-01

    Full text: The internal monitoring programme are carried out for the occupationally exposed workers that develop activities in the radioisotope production plant, fuel cycle facilities, waste management installations, cyclotron and the reactor facility at Institute of Nuclear Energy and Research (IPEN). According to the National Nuclear Energy Commission (CNEN), Regulation NN-3.01, the dose of each worker should be maintained at least for a period of 30 years. With this purpose, an online system, called 'IntDosWeb', was developed with the objective of the management for data dosimetric of internal monitoring programme. The system IntDosWeb, based on free software, was developed in programming language PHP and environment database PostgreSQL. This system is to be available at the local net, Intranet. The database maintains information about identification of the worker that handles non-sealed radioactive sources, physical and chemical characteristics of the radionuclides, monitoring types, measurement data and the dose. This system is able to generate annual reports of the individuals and the historical dose. Several simulation cases have been put into effect to check the on-line software functional capabilities. The users can access the dosimetric information according to following database field: monitoring period, monitoring type, intake pattern, radionuclide type and monitoring data from a specific installation or from each worker. The system was tested in the routinely service of internal dosimetry at IPEN. The rastreability of the information made in the internal monitoring programme was a success and also guaranteeing the reliability and integrity of the stored information. The IntDosWeb was shown as a helpful tool for analysis of the committed effective dose in the radiation protection programme, besides obeying the legal demands of the Brazilian Regulatory Commission. (author)

  11. International trade and the position of European low-skilled labour

    OpenAIRE

    Jansen, Marion

    2000-01-01

    This paper presents a discussion of the potential channels through which international trade affects the position of low skilled workers in the European Union. After an analysis of the European Union's trade flows showing the predominant role of intra-industry trade with other industrialised countries, the discussion focuses on the potential effects of intra-industry trade on low skilled labour. Particular attention is paid to possible interactions between trade and technological change and t...

  12. Spatial Spectroscopy Approach for Detection of Internal Defect of Component without Zero-Position Sensors

    Directory of Open Access Journals (Sweden)

    Qizhou Wu

    2016-01-01

    Full Text Available Conventional approach to detect the internal defect of a component needs sensors to mark the “zero” positions, which is time-consuming and lowers down the detecting efficiency. In this study, we proposed a novelty approach that uses spatial spectroscopy to detect internal defect of objects without zero-position sensors. Specifically, the spatial variation wave of distance between the detecting source and object surface is analyzed, from which a periodical cycle is determined with the correlative approaches. Additionally, a wavelet method is adopted to reduce the noise of the periodic distance signal. This approach is validated by the ultrasound detection of a component with round cross section and elliptical shape in axis. The experimental results demonstrate that this approach greatly saves the time spent on the judgment of a complete cycle and improves the detecting efficiency of internal defect in the component. The approach can be expanded to other physical methods for noninvasive detection of internal defect, such as optical spectroscopy or X-ray scanning, and it can be used for hybrid medium, such as biological tissues.

  13. A configurable electronics system for the ESS-Bilbao beam position monitors

    Energy Technology Data Exchange (ETDEWEB)

    Muguira, L., E-mail: lmuguira@essbilbao.org [ESS-Bilbao, Edificio Rectorado, Vivero de Empresas, 48940 Leioa (Bizkaia) (Spain); Belver, D. [ESS-Bilbao, Edificio Rectorado, Vivero de Empresas, 48940 Leioa (Bizkaia) (Spain); Etxebarria, V. [University of Basque Country (UPV/EHU), Department of Electricity and Electronics, Science and Technology Faculty, 48940 Leioa (Bizkaia) (Spain); Varnasseri, S.; Arredondo, I.; Campo, M. del; Echevarria, P.; Garmendia, N.; Feuchtwanger, J. [ESS-Bilbao, Edificio Rectorado, Vivero de Empresas, 48940 Leioa (Bizkaia) (Spain); Jugo, J.; Portilla, J. [University of Basque Country (UPV/EHU), Department of Electricity and Electronics, Science and Technology Faculty, 48940 Leioa (Bizkaia) (Spain)

    2013-09-01

    A versatile and configurable system has been developed in order to monitorize the beam position and to meet all the requirements of the future ESS-Bilbao Linac. At the same time the design has been conceived to be open and configurable so that it could eventually be used in different kinds of accelerators, independent of the charged particle, with minimal change. The design of the Beam Position Monitors (BPMs) system includes a test bench both for button-type pick-ups (PU) and striplines (SL), the electronic units and the control system. The electronic units consist of two main parts. The first part is an Analog Front-End (AFE) unit where the RF signals are filtered, conditioned and converted to base-band. The second part is a Digital Front-End (DFE) unit which is based on an FPGA board where the base-band signals are sampled in order to calculate the beam position, the amplitude and the phase. To manage the system a Multipurpose Controller (MC) developed at ESSB has been used. It includes the FPGA management, the EPICS integration and Archiver Instances. A description of the system and a comparison between the performance of both PU and SL BPM designs measured with this electronics system are fully described and discussed. -- Author-Highlights: • A versatile and configurable BPM system for the ESS-Bilbao Linac has been designed. • The design works for PU and SL detectors, both in continuous and pulsed wave modes. • Several tests at simulated beamlines at 352 MHz and 175 MHz have been performed. • The BPM system has been integrated in EPICS and Archiver.

  14. Long bunch trains measured using a prototype cavity beam position monitor for the Compact Linear Collider

    Directory of Open Access Journals (Sweden)

    F. J. Cullinan

    2015-11-01

    Full Text Available The Compact Linear Collider (CLIC requires beam position monitors (BPMs with 50 nm spatial resolution for alignment of the beam line elements in the main linac and beam delivery system. Furthermore, the BPMs must be able to make multiple independent measurements within a single 156 ns long bunch train. A prototype cavity BPM for CLIC has been manufactured and tested on the probe beam line at the 3rd CLIC Test Facility (CTF3 at CERN. The transverse beam position is determined from the electromagnetic resonant modes excited by the beam in the two cavities of the pickup, the position cavity and the reference cavity. The mode that is measured in each cavity resonates at 15 GHz and has a loaded quality factor that is below 200. Analytical expressions for the amplitude, phase and total energy of signals from long trains of bunches have been derived and the main conclusions are discussed. The results of the beam tests are presented. The variable gain of the receiver electronics has been characterized using beam excited signals and the form of the signals for different beam pulse lengths with the 2/3  ns bunch spacing has been observed. The sensitivity of the reference cavity signal to charge and the horizontal position signal to beam offset have been measured and are compared with theoretical predictions based on laboratory measurements of the BPM pickup and the form of the resonant cavity modes as determined by numerical simulation. Finally, the BPM was calibrated so that the beam position jitter at the BPM location could be measured. It is expected that the beam jitter scales linearly with the beam size and so the results are compared to predicted values for the latter.

  15. Respiratory gating based on internal electromagnetic motion monitoring during stereotactic liver radiation therapy: First results.

    Science.gov (United States)

    Poulsen, Per Rugaard; Worm, Esben Schjødt; Hansen, Rune; Larsen, Lars Peter; Grau, Cai; Høyer, Morten

    2015-01-01

    Intrafraction motion may compromise the target dose in stereotactic body radiation therapy (SBRT) of tumors in the liver. Respiratory gating can improve the treatment delivery, but gating based on an external surrogate signal may be inaccurate. This is the first paper reporting on respiratory gating based on internal electromagnetic monitoring during liver SBRT. Two patients with solitary liver metastases were treated with respiratory-gated SBRT guided by three implanted electromagnetic transponders. The treatment was delivered in end-exhale with beam-on when the centroid of the three transponders deviated less than 3 mm [left-right (LR) and anterior-posterior (AP) directions] and 4mm [cranio-caudal (CC)] from the planned position. For each treatment fraction, log files were used to determine the transponder motion during beam-on in the actual gated treatments and in simulated treatments without gating. The motion was used to reconstruct the dose to the clinical target volume (CTV) with and without gating. The reduction in D95 (minimum dose to 95% of the CTV) relative to the plan was calculated for both treatment courses. With gating the maximum course mean (standard deviation) geometrical error in any direction was 1.2 mm (1.8 mm). Without gating the course mean error would mainly increase for Patient 1 [to -2.8 mm (1.6 mm) (LR), 7.1 mm (5.8 mm) (CC), -2.6 mm (2.8mm) (AP)] due to a large systematic cranial baseline drift at each fraction. The errors without gating increased only slightly for Patient 2. The reduction in CTV D95 was 0.5% (gating) and 12.1% (non-gating) for Patient 1 and 0.3% (gating) and 1.7% (non-gating) for Patient 2. The mean duty cycle was 55%. Respiratory gating based on internal electromagnetic motion monitoring was performed for two liver SBRT patients. The gating added robustness to the dose delivery and ensured a high CTV dose even in the presence of large intrafraction motion.

  16. Monitoring the electron beam position at the TESLA test facility free electron laser

    International Nuclear Information System (INIS)

    Kamps, T.

    2000-01-01

    The operation of a free electron laser working in the Self Amplified Spontaneous Emission mode (SASE FEL) requires the electron trajectory to be aligned with very high precision in overlap with the photon beam. In order to ensure this overlap, one module of the SASE FEL undulator at the TESLA Test Facility (TTF) is equipped with a new type of waveguide beam position monitor (BPM). Four waveguides are arranged symmetrically around the beam pipe, each channel couples through a small slot to the electromagnetic beam field. The induced signal depends on the beam intensity and on the transverse beam position in terms of beam-to-slot distance. With four slot--waveguide combinations a linear position sensitive signal can be achieved, which is independent of the beam intensity. The signals transduced by the slots are transferred by ridged waveguides through an impedance matching stage into a narrowband receiver tuned to 12 GHz. The present thesis describes design, tests, and implementation of this new type of BPM. (orig.)

  17. Ion beam induced surface graphitization of CVD diamond for x-ray beam position monitor applications

    International Nuclear Information System (INIS)

    Liu, Chian; Shu, D.; Kuzay, T.M.; Wen, L.; Melendres, C.A.; Argonne National Lab., IL

    1996-01-01

    The Advanced Photon Source at ANL is a third-generation synchrotron facility that generates powerful x-ray beams on its undulator beamlines. It is important to know the position and angle of the x- ray beam during experiments. Due to very high heat flux levels, several patented x-ray beam position monitors (XBPM) exploiting chemical vapor deposition (CVD) diamond have been developed. These XBPMs have a thin layer of low-atomic-mass metallic coating so that photoemission from the x rays generate a minute but measurable current for position determination. Graphitization of the CVD diamond surface creates a very thin, intrinsic and conducting layer that can stand much higher temperatures and minimal x-ray transmission losses compared to the coated metallic layers. In this paper, a laboratory sputter ion source was used to transform selected surfaces of a CVD diamond substrate into graphite. The effect of 1-5 keV argon ion bombardment on CVD diamond surfaces at various target temperatures from 200 to 500 C was studied using Auger electron spectroscopy and in-situ electrical resistivity measurements. Graphitization after the ion bombardment has been confirmed and optimum conditions for graphitization studied. Raman spectroscopy was used to identify the overall diamond structure in the bulk of CVD diamond substrate after the ion bombardments. It was found that target temperature plays an important role in stability and electrical conductivity of the irradiated CVD diamonds

  18. Monitoring of Diaphragm Position in Pulsatile Pnumatic Ventricular Assisted Device by Ultrasound Sensor

    Science.gov (United States)

    Kamimura, Tadayuki; Homma, Akihiko; Tsukiya, Tomonori; Kakuta, Yukihide; Lee, Hwansung; Tatsumi, Eisuke; Taenaka, Yoshiyuki; Kitamura, Soichiro

    A new method using ultrasound sensors to detect the diaphragm position of a ventricular assist device (VAD) was proposed. Two small ultrasound sensors of 2.4mm diameter were attached to the outside surface of blood chamber of a pneumatic VAD. The receiving crystal received the ultrasound from the transmitting crystal reflected by the diaphragm. The diaphragm position was calculated by using geometric relation among two sensors and ultrasound propagation time. Validity of this method was evaluated in a mock circulation test under various driving conditions of VAD by comparing the ultrasound signals with driving pressure waveforms. The ultrasound signals could detect full-fill (FF) and full-eject (FE) status shortly before the spikes appeared on pressure waves, which are currently available to detect FE and FF but accompanies excessive extension of the diaphragm. This method would be helpful to avoid overloading of diaphragm. Linear correlation was observed between the output from VAD and blood volume calculated from the change of diaphragm position multiplied by the heart rate. This monitoring method of diaphragm of a VAD was proven to have advantages over the current method toward better control of a pneumatic VAD.

  19. The problems of individual monitoring for internal exposure of monazite storage facility workers

    International Nuclear Information System (INIS)

    Ekidin, A.; Kirdin, I.; Yarmoshenko, I.; Zhukovsky, M.

    2006-01-01

    traditionally two situations of internal inhalation exposure by alpha emitting nuclides are considered in radiological protection: occupational exposure due to inhalation of plutonium aerosols; inhalation exposure by 222 Rn daughters in working places and in home. for these situations the problems of radioactive aerosols intake, nuclide dynamics in human body, internal dosimetry, nuclide excretion, monitoring of internal exposure have been investigated in details especially for plutonium inhalation exposure. The results of these studies are presented in details in ICRP Publications and UNSCEAR reports. However there is very specific case in which the special analysis of internal inhalation exposure is need. it is the working places with anomalous, extremely high concentration of thoron ( 220 Rn) daughters. The problems of internal radiation exposure of workers in such working place are the main topic of this publication. (authors)

  20. Vibration monitoring of the mechanical behavior of the internal structures of PWR reactors

    International Nuclear Information System (INIS)

    Assedo, R.; Carre, J.C.; Sol, J.C.

    1979-01-01

    The internal structures of pressurized water reactors are the seat of vibrations induced by fluctuations in primary fluid flow. A knowledge of these phenomena is indispensable in order to ensure that the structures are in proper mechanical order. It can also be used for operational monitoring. This paper describes all the methods developed and the results already achieved in this domain. The first part deals with tests on mockup associated with the calculation models which afforded a good knowledge of the vibrational characteristics of the internal structures, as well as the measurements made during hot tests of certain reactors which made it possible to qualify these models on real structures. The second part describes the means of detection (neutron noise, external accelerometers) as well as the processing methods used in the follow-up. A few typical results obtained on site are then presented. Finally, the general principles of operational monitoring of the mechanical behavior of the internal structures are described [fr

  1. Beam position monitor multiplexer controller upgrade at the LAMPF proton storage ring

    International Nuclear Information System (INIS)

    Scarborough, W.K.; Cohen, S.

    1992-01-01

    The beam position monitor (BPM) is one of the primary diagnostic tools used for the tuning of the proton storage ring (PSR) at the Clinton P. Anderson Meson Physics Facility (LAMPF). A replacement for the existing, monolithic, wire-wrapped microprocessor-based BPM multiplexer controller has been built. The controller has been redesigned as a modular system retaining the same functionality of the original system built in 1981. Individual printed circuit cards are used for each controller function to insure greater maintainability and ease of keeping a spare parts inventory. Programmable logic device technology has substantially reduced the component count of the new controller. Diagnostic software was written to support the development of the upgraded controller. The new software actually uncovered some flaws in the original CAMAC interface. (author)

  2. DESIGN AND FABRICATION OF THE BEAM POSITION MONITOR FOR THE PEFP LINAC

    Directory of Open Access Journals (Sweden)

    HYEOK-JUNG KWON

    2013-08-01

    Full Text Available The beam position monitor (BPM is an essential component for the PEFP 100-MeV linac's commissioning. A prototype stripline-type linac BPM was designed for this purpose. The electrode aperture is 20 mm in diameter, and the electrode is 25 mm long, so it can be installed between Drift Tube Linac (DTL101 and DTL102, which is the shortest distance. One end of the electrode is connected to the Sub Miniature Type A (SMA feed through for signal measurement, and the other end is terminated as a short. The signal amplitude of the fundamental component was calculated and compared with that of the second harmonic component. The designed BPM was fabricated and a low-power RF test was conducted. In this paper, the design, fabrication and low power test of the BPM for the PEFP linac are presented.

  3. Low-emittance tuning of storage rings using normal mode beam position monitor calibration

    Directory of Open Access Journals (Sweden)

    A. Wolski

    2011-07-01

    Full Text Available We describe a new technique for low-emittance tuning of electron and positron storage rings. This technique is based on calibration of the beam position monitors (BPMs using excitation of the normal modes of the beam motion, and has benefits over conventional methods. It is relatively fast and straightforward to apply, it can be as easily applied to a large ring as to a small ring, and the tuning for low emittance becomes completely insensitive to BPM gain and alignment errors that can be difficult to determine accurately. We discuss the theory behind the technique, present some simulation results illustrating that it is highly effective and robust for low-emittance tuning, and describe the results of some initial experimental tests on the CesrTA storage ring.

  4. Cavity beam position monitor system for the Accelerator Test Facility 2

    Directory of Open Access Journals (Sweden)

    Y. I. Kim

    2012-04-01

    Full Text Available The Accelerator Test Facility 2 (ATF2 is a scaled demonstrator system for final focus beam lines of linear high energy colliders. This paper describes the high resolution cavity beam position monitor (BPM system, which is a part of the ATF2 diagnostics. Two types of cavity BPMs are used, C-band operating at 6.423 GHz, and S-band at 2.888 GHz with an increased beam aperture. The cavities, electronics, and digital processing are described. The resolution of the C-band system with attenuators was determined to be approximately 250 nm and 1  μm for the S-band system. Without attenuation the best recorded C-band cavity resolution was 27 nm.

  5. Detection of coherent beam-beam modes with digitized beam position monitor signals

    CERN Document Server

    Stancari, G.; White, S.M.

    2014-01-01

    A system for bunch-by-bunch detection of transverse proton and antiproton coherent oscillations in the Fermilab Tevatron collider is described. It is based on the signal from a single beam-position monitor located in a region of the ring with large amplitude functions. The signal is digitized over a large number of turns and Fourier-analyzed offline with a dedicated algorithm. To enhance the signal, band-limited noise is applied to the beam for about 1 s. This excitation does not adversely affect the circulating beams even at high luminosities. The device has a response time of a few seconds, a frequency resolution of $1.6\\times 10^{-5}$ in fractional tune, and it is sensitive to oscillation amplitudes of 60 nm. It complements Schottky detectors as a diagnostic tool for tunes, tune spreads, and beam-beam effects. Measurements of coherent mode spectra are presented and compared with models of beam-beam oscillations.

  6. Numerical analysis of the beam position monitor pickup for the Iranian light source facility

    Science.gov (United States)

    Shafiee, M.; Feghhi, S. A. H.; Rahighi, J.

    2017-03-01

    In this paper, we describe the design of a button type Beam Position Monitor (BPM) for the low emittance storage ring of the Iranian Light Source Facility (ILSF). First, we calculate sensitivities, induced power and intrinsic resolution based on solving Laplace equation numerically by finite element method (FEM), in order to find the potential at each point of BPM's electrode surface. After the optimization of the designed BPM, trapped high order modes (HOM), wakefield and thermal loss effects are calculated. Finally, after fabrication of BPM, it is experimentally tested by using a test-stand. The results depict that the designed BPM has a linear response in the area of 2×4 mm2 inside the beam pipe and the sensitivity of 0.080 and 0.087 mm-1 in horizontal and vertical directions. Experimental results also depict that they are in a good agreement with numerical analysis.

  7. Positional demands of international rugby union: evaluation of player actions and movements.

    Science.gov (United States)

    Quarrie, Kenneth L; Hopkins, Will G; Anthony, Mike J; Gill, Nicholas D

    2013-07-01

    In rugby union, published analyses of actions and movements of players during matches have been limited to small samples of games at regional or national level. To analyse movements and activities of players in international rugby union matches with a sample size sufficient to clearly delineate positional roles. Observational study. Actions of 763 players were coded from video recordings of 90 international matches played by the New Zealand national team (the All Blacks) from 2004 to 2010. Movements of players were coded for 27 of these matches via a semi-automated player-tracking system. Movements and activities of all players from both teams were coded. Cluster analysis of activities and time-motion variables produced five subgroups of forwards (props, hookers, locks, flankers, Number 8 forwards) and five subgroups of backs (scrum-half, fly-half, midfield backs, wings and fullbacks). Forwards sustained much higher contact loads per match than backs, via scrums, rucks, tackles and mauls. Mean distance covered per match ranged from 5400 to 6300m, with backs generally running further than forwards. There were marked differences between positional groups in the amount of distance covered at various speeds. The amount of play per match varies by position due to differences in rates at which players are substituted. The distance covered by players at relatively fast running speeds (in excess of 5ms(-1)) appears to be higher during international matches than when competing at lower levels of the professional game. The specific match demands for positional groups need to be considered when managing player workloads. Copyright © 2012 Sports Medicine Australia. Published by Elsevier Ltd. All rights reserved.

  8. Resolution and drift measurements on the Advanced Photon Source beam position monitors

    International Nuclear Information System (INIS)

    Chung, Y.; Kahana, E.

    1994-01-01

    The resolution and long-term drift of the Advanced Photon Source (APS) beam position monitor (BPM) electronics were measured using the charged particle beams in the ESRF storage ring with various beam current and configurations (single bunch, 8 and 16 equally spaced bunches, and 1/3-fill). The energy of the stored electrons was 6 GeV. The integrated BPM electronics system as used for this work is capable of measuring the beam position on a turn-by-turn basis, which can be accumulated for N turns (N = 2 n , n = 1, 2, ... , 11). Estimation of the BPM resolution apart from the low-frequency beam motion was made by measuring the standard deviation in the measured beam position with different Ns. The analysis of the results indicates a BPM resolution of 18/√ N [μm] for the APS storage ring, which is equivalent to 0.07 μm/√Hz. For the miniature insertion device BPM with 2.8 times higher sensitivity, the resolution will be 0.02 μm/√Hz. The long-term drift of the BPM electronics independent of the actual beam motion was measured at 2 μm/hr, which settled after approximately 1.5 hours. This drift can be attributed mainly to the temperature effect. Comparison of the results with the laboratory measurements shows good agreement. Implication of the BPM resolution limit on the proposed global and local beam position feedback systems for the APS storage ring will also be discussed

  9. Three-dimensional surface scanning for accurate patient positioning and monitoring during breast cancer radiotherapy

    Energy Technology Data Exchange (ETDEWEB)

    Gaisberger, C.; Mitterlechner, B.; Huber, S.; Weichenberger, H.; Sedlmayer, F.; Deutschmann, H. [Paracelsus Medical Univ. Clinics, Salzburg (Austria). Dept. of Radiotherapy and Radio-Oncology; Paracelsus Medical Univ., Salzburg (Austria). Inst. for Research and Development of Advanced Radiation Technologies (radART); Steininger, P. [Paracelsus Medical Univ., Salzburg (Austria). Inst. for Research and Development of Advanced Radiation Technologies (radART)

    2013-10-15

    Purpose: Clinical evaluation of an optical three-dimensional surface scanning (3D-SS) system for patient positioning and monitoring during radiotherapy (RT) for breast cancer. Materials and methods: A ceiling-mounted scanner was developed to acquire multiple 3D body surface images and tested in 14 conservatively operated breast cancer patients. A reference skin surface was derived from the planning computed tomography (CT) scan as basis for rigid registration with the surface scans. In addition to electronic portal images (EPIs), optical scans were acquired at three defined time points before and during daily RT. Patient setup was guided by laser alignments and corrected according to EPI findings. The accuracy of the 3D-SS system was validated by comparison of the optical scans to EPIs generated in parallel. Interfraction shifts were investigated by comparison of the first 3D-SS image with the reference body outline. Intrafractional motions were analysed by comparing the three daily surface scans with the first EPI. Results: Comparison of EPIs and 3D-SS images revealed good accordance (- 0.05 {+-} 0.94 mm). Analysis of daily patient positions revealed average deviations of 0.4 {+-} 2.4 mm laterally, 0.3 {+-} 1.9 mm longitudinally and 0.2 {+-} 3.3 mm vertically. After 2 weeks, a systematic interfraction shift in patient positioning was noted, particularly in the vertical direction (4.9 {+-} 0.56 mm), which was attributed to patients progressively relaxing. 3D-SS images showed intrafractional shifts of 1.2 {+-} 0.7 mm over a time course of 2 min. Conclusion: Optical surface scanning is a simple, fast and reproducible method for breast cancer patient alignment. Particularly for more sophisticated irradiation techniques, it helps to improve accuracy in patient positioning during radiotherapy without the exposure to additional ionizing radiation. (orig.)

  10. Nonlinear Ultrasonic Techniques to Monitor Radiation Damage in RPV and Internal Components

    Energy Technology Data Exchange (ETDEWEB)

    Jacobs, Laurence [Georgia Inst. of Technology, Atlanta, GA (United States); Kim, Jin-Yeon [Georgia Inst. of Technology, Atlanta, GA (United States); Qu, Jisnmin [Northwestern Univ., Evanston, IL (United States); Ramuhalli, Pradeep [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wall, Joe [Electric Power Research Inst. (EPRI), Knoxville, TN (United States)

    2015-11-02

    The objective of this research is to demonstrate that nonlinear ultrasonics (NLU) can be used to directly and quantitatively measure the remaining life in radiation damaged reactor pressure vessel (RPV) and internal components. Specific damage types to be monitored are irradiation embrittlement and irradiation assisted stress corrosion cracking (IASCC). Our vision is to develop a technique that allows operators to assess damage by making a limited number of NLU measurements in strategically selected critical reactor components during regularly scheduled outages. This measured data can then be used to determine the current condition of these key components, from which remaining useful life can be predicted. Methods to unambiguously characterize radiation related damage in reactor internals and RPVs remain elusive. NLU technology has demonstrated great potential to be used as a material sensor – a sensor that can continuously monitor a material’s damage state. The physical effect being monitored by NLU is the generation of higher harmonic frequencies in an initially monochromatic ultrasonic wave. The degree of nonlinearity is quantified with the acoustic nonlinearity parameter, β, which is an absolute, measurable material constant. Recent research has demonstrated that nonlinear ultrasound can be used to characterize material state and changes in microscale characteristics such as internal stress states, precipitate formation and dislocation densities. Radiation damage reduces the fracture toughness of RPV steels and internals, and can leave them susceptible to IASCC, which may in turn limit the lifetimes of some operating reactors. The ability to characterize radiation damage in the RPV and internals will enable nuclear operators to set operation time thresholds for vessels and prescribe and schedule replacement activities for core internals. Such a capability will allow a more clear definition of reactor safety margins. The research consists of three tasks: (1

  11. 4th International Conference on Condition Monitoring of Machinery in Non-Stationary Operations

    CERN Document Server

    Zimroz, Radoslaw; Bartelmus, Walter; Haddar, Mohamed

    2016-01-01

    The book provides readers with a snapshot of recent research and technological trends in the field of condition monitoring of machinery working under a broad range of operating conditions. Each chapter, accepted after a rigorous peer-review process, reports on an original piece of work presented and discussed at the 4th International Conference on Condition Monitoring of Machinery in Non-stationary Operations, CMMNO 2014, held on December 15-16, 2014, in Lyon, France. The contributions have been grouped into three different sections according to the main subfield (signal processing, data mining, or condition monitoring techniques) they are related to. The book includes both theoretical developments as well as a number of industrial case studies, in different areas including, but not limited to: noise and vibration; vibro-acoustic diagnosis; signal processing techniques; diagnostic data analysis; instantaneous speed identification; monitoring and diagnostic systems; and dynamic and fault modeling. This book no...

  12. Internal Impingement of the Shoulder: A Risk of False Positive Test Outcomes in External Impingement Tests?

    Directory of Open Access Journals (Sweden)

    Tim Leschinger

    2017-01-01

    Full Text Available Background. External impingement tests are considered as being particularly reliable for identifying subacromial and coracoid shoulder impingement mechanisms. The purpose of the present study was to evaluate if these tests are likely to provoke an internal shoulder impingement mechanism which, in cases of a pathologic condition, can lead to a positive test result. Method. In 37 subjects, the mechanical contact between the glenoid rim and the rotator cuff (RC was measured quantitatively and qualitatively in external impingement test positions using an open MRI system. Results. Mechanical contact of the supraspinatus with the posterosuperior glenoid was present in 30 subjects in the Neer test. In the Hawkins test, the subscapularis was in contact with the anterosuperior glenoid in 33 subjects and the supraspinatus in 18. In the horizontal impingement test, anterosuperior contact of the supraspinatus with the glenoid was identified in 35 subjects. Conclusion. The Neer, Hawkins, and horizontal impingement tests are likely to provoke the mechanism of an internal shoulder impingement. A posterosuperior internal impingement mechanism is being provoked predominately in the Neer test. The Hawkins test narrows the distance between the insertions of the subscapularis and supraspinatus and the anterosuperior labrum, which leads to an anterosuperior impingement mechanism.

  13. Adopting the international financial reporting standards: a positive impact on 2004 income and consolidated equity

    Energy Technology Data Exchange (ETDEWEB)

    Mallet, O

    2005-03-01

    This document provides preliminary information on the quantitative impact of transition to the International Financial Reporting Standards (IFRS) on AREVA 2004 financial position, in accordance with AMF recommendations regarding financial communications during the transition period.The basis for preparing 2004 information on transition to the IFRS comes from: the International Accounting Standards (IAS)/IFRS, as approved by the European Union. The impact of IAS 32/39 and IFRS 4 will not be recognized in shareholders equity until January 1, 2005; AREVA anticipation of the resolution of technical issues and ongoing projects under discussion by the International Accounting Standards Board (IASB) and the International Financial Reporting Interpretations Committee (IFRIC). Uncertainty factors on practical methods for applying certain standards and ongoing interpretations by IFRIC and regulatory organizations could impact the exactness of restatements identified at this stage. For all of these reasons, it is conceivable that the opening balance sheet at January 1, 2004, as presented in this document, will not be the balance sheet actually used to establish the consolidated financial statements for 2005. (author)

  14. Advanced laser-based tracking device for motor vehicle lane position monitoring and steering assistance

    Science.gov (United States)

    Bachalo, William D.; Inenaga, Andrew; Schuler, Carlos A.

    1995-12-01

    Aerometrics is developing an innovative laser-diode based device that provides a warning signal when a motor-vehicle deviates from the center of the lane. The device is based on a sensor that scans the roadway on either side of the vehicle and determines the lateral position relative to the existing painted lines marking the lane. No additional markings are required. A warning is used to alert the driver of excessive weaving or unanticipated departure from the center of the lane. The laser beams are at invisible wavelengths to that operation of the device does not pose a distraction to the driver or other motorists: When appropriate markers are not present on the road, the device is capable of detecting this condition and warn the driver. The sensor system is expected to work well irrespective of ambient light levels, fog and rain. This sensor has enormous commercial potential. It could be marketed as an instrument to warn drivers that they are weaving, used as a research tool to monitor driving patterns, be required equipment for those previously convicted of driving under the influence, or used as a backup sensor for vehicle lateral position control. It can also be used in storage plants to guide robotic delivery vehicles. In this paper, the principles of operation of the sensor, and the results of Aerometrics ongoing testing will be presented.

  15. Beam position monitor R&D for keV ion beams

    CERN Document Server

    Naveed, S; Nosych, A; Søby,L

    2013-01-01

    Beams of cooled antiprotons at keV energies shall be provided by the Ultra-low energy Storage Ring (USR) at the Facility for Low energy Antiproton and Ion Research (FLAIR) and the Extra Low ENergy Antiproton ring (ELENA) at CERN's Antiproton Decelerator (AD) facility. Both storage rings put challenging demands on the beam position monitoring (BPM) system as their capacitive pick-ups should be capable of determining the beam position of beams at low intensities and low velocities, close to the noise level of state-of-the-art electronics. In this contribution we describe the design and anticipated performance of BPMs for low-energy ion beams with a focus on the ELENA orbit measurement systems. We also present the particular challenges encountered in the numerical simulation of pickup response at very low beta values. Finally, we provide an outlook on how the implementation of faster algorithms for the simulation of BPM characteristics could potentially help speed up such studies considerably.

  16. Development of a high-resolution cavity-beam position monitor

    Directory of Open Access Journals (Sweden)

    Yoichi Inoue

    2008-06-01

    Full Text Available We have developed a high-resolution cavity-beam position monitor (BPM to be used at the focal point of the ATF2, which is a test beam line that is now being built to demonstrate stable orbit control at ∼nanometer resolution. The design of the cavity structure was optimized for the Accelerator Test Facility (ATF beam in various ways. For example, the cavity has a rectangular shape in order to isolate two dipole modes in orthogonal directions, and a relatively thin gap that is less sensitive to trajectory inclination. A two stage homodyne mixer with highly sensitive electronics and phase-sensitive detection was also developed. Two BPM blocks, each containing two cavity BPMs, were installed in the existing ATF beam line using a rigid support frame. After testing the basic characteristics, we measured the resolution using three BPMs. The system demonstrated 8.7 nm position resolution over a dynamic range of 5  μm.

  17. Internal exposure monitoring of personnel of a nuclear power plant with pressurized-water reactors

    International Nuclear Information System (INIS)

    Krueger, F.W.; Poulheim, K.F.; Rueger, G.; Schreiter, W.D.

    1982-01-01

    In the GDR a programme for monitoring the internal radiation exposure of personnel has been established in the Bruno Leuschner Nuclear Power Plant, Greifswald, which allows one to estimate the effective dose equivalent in the way recommended by the ICRP. The measuring equipment used, and the methods of calibration and of evaluation of results are described. At present about 400 persons are monthly monitored with a thorax monitor in the nuclear power plant. If an investigation level - corresponding to an effective dose equivalent of 0.3mSv/month - is exceeded, a more exact measurement is made in the whole-body counter at the National Board for Nuclear Safety and Radiation Protection of the GDR. In addition, a selected group of 50 persons is measured twice yearly in the whole-body counter. The measurements show the high effectiveness of the protective measures against radionuclide intake by workers in the nuclear power plant, resulting in a contribution of less than 1% to the collective dose of the personnel. A correlation has been found between external and internal exposure indicating that, in general, there will be a higher intake only under conditions resulting also in higher external exposures. The highest individual values of internal exposure found are below 0.5mSv/month and thus within the range of the lower detection limit of dosimeter films used for monitoring the external exposure. (author)

  18. Individual internal monitoring of workers of Fabrica de Combustivel Nuclear - FCN

    International Nuclear Information System (INIS)

    Castro, Marcelo X.

    2005-01-01

    In nuclear fuel fabrication facilities, workers are exposed to different compounds of enriched uranium. Due to the high cost of the individual monitoring programme for internal dose assessment in the routine monitoring programmes, usually only one type of measurement is assigned. In complex situations like the one described in this paper, where several parameters can compromise the accuracy of the bioassay interpretation it is need to have a combination of techniques to evaluate the internal dose. According to ICRP 78 (1997), the general order of preference in terms of accuracy of interpretation is: body activity measurement, excreta analysis and personal air sampling. A group of fifteen workers from controlled area of the fuel fabrication facility was selected to evaluate the internal dose using all different available techniques during a certain period. The workers were monitored for determination of uranium content in the daily urinary excretion, faecal excretion, chest counting and personal air sampling (PAS). The results have shown that at least two types of sensitivity techniques must be used, since there are some sources of uncertainties on the bioassay interpretation, like mixture of uranium compounds intake and different routes of intake. The combination of urine and faeces analysis has shown be the more appropriate methodology for assessing internal dose in this situation. (author)

  19. Employing moderate resolution sensors in human rights and international humanitarian law monitoring

    Science.gov (United States)

    Marx, Andrew J.

    Organizations concerned with human rights are increasingly using remote sensing as a tool to improve their detection of human rights and international humanitarian law violations. However, as these organizations have transitioned to human rights monitoring campaigns conducted over large regions and extended periods of time, current methods of using fine- resolution sensors and manpower-intensive analyses have become cost- prohibitive. To support the continued growth of remote sensing in human rights and international humanitarian law monitoring campaigns, this study researches how moderate resolution land observatories can provide complementary data to operational human rights monitoring efforts. This study demonstrates the capacity of moderate resolutions to provide data to monitoring efforts by developing an approach that uses Landsat Enhanced Thematic Mapper Plus (ETM+) as part of a system for the detection of village destruction in Darfur, Sudan. Village destruction is an indicator of a human rights or international humanitarian law violations in Darfur during the 2004 study period. This analysis approach capitalizes on Landsat's historical archive and systematic observations by constructing a historic spectral baseline for each village in the study area that supports automated detection of a potentially destroyed village with each new overpass of the sensor. Using Landsat's near-infrared band, the approach demonstrates high levels of accuracy when compared with a U.S. government database documenting destroyed villages. This approach is then applied to the Darfur conflict from 2002 to 2008, providing new data on when and where villages were destroyed in this widespread and long-lasting conflict. This application to the duration of a real-world conflict illustrates the abilities and shortcomings of moderate resolution sensors in human rights monitoring efforts. This study demonstrates that moderate resolution satellites have the capacity to contribute

  20. Ground truth data collection on mining industrial explosions registered by the International Monitoring System

    International Nuclear Information System (INIS)

    Ehl'tekov, A.Yu.; Gordon, V.P.; Firsov, V.A.; Chervyakov, V.B.

    2004-01-01

    The presentation is dedicated to organizational and technical issues connected with the task of Comprehensive Test-Ban-Treaty Organization timely notification on large chemical explosions including data on explosion location and time, on applied explosive substance quantity and type, and also on configuration and assumed purpose of explosion. Explosions registered by International Monitoring System are of special interest. Their data could be used for calibration of the monitoring system. Ground truth data collection and some explosions location results on Russia's mining enterprises were given. Ground truth data collection peculiarities according to mining industrial explosions were considered. (author)

  1. Assessment of necessary regularity of internal irradiation monitoring on the basis of direct and indirect methods of dosimetry

    International Nuclear Information System (INIS)

    Malykhin, V.M.; Ivanova, N.I.

    1981-01-01

    It is shown that when assessing the necessary periodicity of internal irradiation monitoring, it is required to take account of the nature (rhythm) of radionuclide intake to the organism during the monitoring period, the effective period of radionuclide biological half-life, its activity in the organism, sensitivity of the technique applied and the labour-consumig character of the monitoring method [ru

  2. A Prospective Cohort Study of Gated Stereotactic Liver Radiation Therapy Using Continuous Internal Electromagnetic Motion Monitoring

    DEFF Research Database (Denmark)

    Worm, Esben S; Høyer, Morten; Hansen, Rune

    2018-01-01

    PURPOSE: Intrafraction motion can compromise the treatment accuracy in liver stereotactic body radiation therapy (SBRT). Respiratory gating can improve treatment delivery; however, gating based on external motion surrogates is inaccurate. The present study reports the use of Calypso-based internal.......0 percentage points (range 0.7-22.0) without gating and 0.8 percentage point (range 0.2-2.0) with gating. CONCLUSIONS: Gating using internal motion monitoring was successfully applied for liver SBRT. It markedly improved the geometric and dosimetric accuracy compared with nongated standard treatment....

  3. Monitoring for Radioactive Material in International Mail Transported by Public Postal Operators. Reference Manual (Chinese Edition)

    International Nuclear Information System (INIS)

    2012-01-01

    The illegal transport of conventional explosives and biological material has been observed in public mail and could lead to serious health hazards. In response to Member States' requests to establish guidance for detecting the movement of radioactive material in international mail, the IAEA and the Universal Postal Union (UPU) undertook a joint effort to prepare this publication. It considers how radioactive materials in international mail might be detected, how best to monitor for these materials in mail facilities and how to respond appropriately. This publication brings together a concise but comprehensive description of the various techniques and equipment used to detect and control radioactive material during mail processing.

  4. Automated long-term monitoring of parallel microfluidic operations applying a machine vision-assisted positioning method.

    Science.gov (United States)

    Yip, Hon Ming; Li, John C S; Xie, Kai; Cui, Xin; Prasad, Agrim; Gao, Qiannan; Leung, Chi Chiu; Lam, Raymond H W

    2014-01-01

    As microfluidics has been applied extensively in many cell and biochemical applications, monitoring the related processes is an important requirement. In this work, we design and fabricate a high-throughput microfluidic device which contains 32 microchambers to perform automated parallel microfluidic operations and monitoring on an automated stage of a microscope. Images are captured at multiple spots on the device during the operations for monitoring samples in microchambers in parallel; yet the device positions may vary at different time points throughout operations as the device moves back and forth on a motorized microscopic stage. Here, we report an image-based positioning strategy to realign the chamber position before every recording of microscopic image. We fabricate alignment marks at defined locations next to the chambers in the microfluidic device as reference positions. We also develop image processing algorithms to recognize the chamber positions in real-time, followed by realigning the chambers to their preset positions in the captured images. We perform experiments to validate and characterize the device functionality and the automated realignment operation. Together, this microfluidic realignment strategy can be a platform technology to achieve precise positioning of multiple chambers for general microfluidic applications requiring long-term parallel monitoring of cell and biochemical activities.

  5. Automated Long-Term Monitoring of Parallel Microfluidic Operations Applying a Machine Vision-Assisted Positioning Method

    Directory of Open Access Journals (Sweden)

    Hon Ming Yip

    2014-01-01

    Full Text Available As microfluidics has been applied extensively in many cell and biochemical applications, monitoring the related processes is an important requirement. In this work, we design and fabricate a high-throughput microfluidic device which contains 32 microchambers to perform automated parallel microfluidic operations and monitoring on an automated stage of a microscope. Images are captured at multiple spots on the device during the operations for monitoring samples in microchambers in parallel; yet the device positions may vary at different time points throughout operations as the device moves back and forth on a motorized microscopic stage. Here, we report an image-based positioning strategy to realign the chamber position before every recording of microscopic image. We fabricate alignment marks at defined locations next to the chambers in the microfluidic device as reference positions. We also develop image processing algorithms to recognize the chamber positions in real-time, followed by realigning the chambers to their preset positions in the captured images. We perform experiments to validate and characterize the device functionality and the automated realignment operation. Together, this microfluidic realignment strategy can be a platform technology to achieve precise positioning of multiple chambers for general microfluidic applications requiring long-term parallel monitoring of cell and biochemical activities.

  6. Comprehensive test ban treaty international monitoring system security threats and proposed security attributes

    Energy Technology Data Exchange (ETDEWEB)

    Draelos, T.J.; Craft, R.L.

    1996-03-01

    To monitor compliance with a Comprehensive Test Ban Treaty (CTBT), a sensing network, referred to as the International Monitoring System (IMS), is being deployed. Success of the IMS depends on both its ability to preform its function and the international community`s confidence in the system. To ensure these goals, steps must be taken to secure the system against attacks that would undermine it; however, it is not clear that consensus exists with respect to the security requirements that should be levied on the IMS design. In addition, CTBT has not clearly articulated what threats it wishes to address. This paper proposes four system-level threats that should drive IMS design considerations, identifies potential threat agents, and collects into one place the security requirements that have been suggested by various elements of the IMS community. For each such requirement, issues associated with the requirement are identified and rationale for the requirement is discussed.

  7. Rapid monitoring of large groups of internally contaminated people following a radiation accident

    International Nuclear Information System (INIS)

    1994-05-01

    In the management of an emergency, it is necessary to assess the radiation exposures of people in the affected areas. An essential component in the programme is the monitoring of internal contamination. Existing fixed installations for the assessment of incorporated radionuclides may be of limited value in these circumstances because they may be inconveniently sited, oversensitive for the purpose, or inadequately equipped and staffed to cope with the large numbers referred to them. The IAEA considered it important to produce guidance on rapid monitoring of large groups of internally contaminated people. The purpose of this document is to provide Member States with an overview on techniques that can be applied during abnormal or accidental situations. Refs and figs

  8. Analysis of production potential and competitive position of Serbia on the international wine market

    Directory of Open Access Journals (Sweden)

    Petrović Jelena

    2015-01-01

    Full Text Available The purpose of this research is analysis and forecasting of the most important trends on the international wine market, as well as identifying opportunities for wine export from Serbia. The aim of the research is to analyse the movement of the wine production and trade on the international market by applying the appropriate methodology. The paper is structured in the following segments: 1 examining the impact of number of vines and yields per vine on the acheved volume of grape production in the Republic of Serbia in the observed period; 2 examining the competitive position of the Republic of Serbia on the international wine market; and 3 analysis of the value and structure of foreign trade of wine between the Republic of Serbia and other countries. Comparative analysis, correlation analysis and regression analysis are used in the paper. The results of this paper indicate: 1 higher impact of yields per vine on the volume of grape production in relation to the impact of the number of vines on the volume of grape production; 2 increasing deficit of foreign trade of wine between Serbia and other world countries; and 3 that Serbia reduced coverage of import of wine by export of wine in the observed period.

  9. International heat pump status and policy review 1993-1996. Part 2. National Position Papers

    International Nuclear Information System (INIS)

    Breembroek, G.; Lazaro, F.

    1999-07-01

    Four years after the publication of the International heat pump status and policy review, the International Energy Agency (IEA) Heat Pump Centre set out to compile an update of this study. The update reviews developments in the years 1993-96 and provides an outlook on future developments. Where available it includes data on 1997 as well. In 1997, roughly 90 million heat pumps were in operation worldwide (55 million in 1992). The main objective of the update of the International heat pump status and policy review is to provide an assessment of basic factors affecting heat pumps, policy measures regarding heat pumps, the status of various heat pump technologies and the current and expected penetration of heat pumps in all marker sectors. The analysis is based on a survey of the heat pump situation in 18 countries: Austria, Canada, China, Denmark, France, Germany, Greece, Italy, Japan, the Netherlands, Norway, South Africa, South Korea, Spain, Sweden, Switzerland, UK and USA. In part one, for which a separate abstract has been prepared, the information from all these countries is brought together, compared and analysed. The information is gathered from detailed reviews of the situations in the individual countries, the so-called National Position Papers, which can be found in this volume (part two) of the report. The reports reveal that overall the heat pump market showed a favourable development in the years 1993-96

  10. [Position of health at international relations. Part I. Structural dimensions of health].

    Science.gov (United States)

    Cianciara, Dorota; Wysocki, Mirosław J

    2011-01-01

    In the article, the health is perceived as complex, multidimensional concept and not as absence of disease. This is consistent with public health perspective, where public health is regarded as public as well as political activity. It aims to solve health and social problems, depends on analysis of phenomena, needs the negotiations and relies on making decision on feasible directions of changes--what, why, how, where, when and by whom should be done. Public health policy developed as a result of international relations, and UN family fora especially, is regarded as significant for creating of health position. The aim of this article was: (1) the analysis of selected concepts and definitions related to structural dimensions of health, used in UN international arrangements; (2) an attempt to explain the evolution of health structure notions at worldwide agenda. The UN main bodies, programmes and funds working on the health field are mentioned and voting rules in UN General Assembly and World Health Assembly are reminded. The following structural dimensions were considered: (a) well-being, (b) human rights, (c) everyday resource, health potential, (4) equity. All were explored in WHO Constitution, Universal Declaration of Human Rights, International Covenant on Economic, Social and Cultural Rights, Ottawa Charter for Health Promotion and numerous WHA and UN GA resolutions, decisions as well as other documents. Some remarkable differences in English and Polish language versions and meanings were pointed out. It was argued that present perception of structural dimension of health is strongly derived from the preamble of the WHO Constitution adopted and signed on 22 July 1946 by the representatives of 61 States. It is an evidence of the strength of this document and wisdom of its authors. The greater progress is associated. with concepts and notion of organizational dimensions of health perceived as action and processes leading to health. Long-term efforts to strengthen

  11. The Military Spouse Education and Career Opportunities Program: Recommendations for an Internal Monitoring System

    Science.gov (United States)

    2016-01-01

    have a surplus of posi- tions available for teachers of English as a Second Language because the federal government changed the national immigration...mycaa/Career/Search.aspx Swan, Gerry, “Tools for Data-Driven Decision Making in Teacher Education ,” Journal of Computing in Teacher Education , Vol...The Military Spouse Education and Career Opportunities Program Recommendations for an Internal Monitoring System Gabriella C. Gonzalez, Laura L

  12. Ultrasound monitoring in cannulation of the internal jugular vein: anatomic and technical considerations.

    Science.gov (United States)

    Docktor, B; So, C B; Saliken, J C; Gray, R R

    1996-06-01

    To examine the effect of variations in anatomic features and operator experience on the success and complication rates of sonographically monitored cannulation of the internal jugular vein. The authors prospectively collected data for ultrasound-monitored cannulation of the internal jugular vein in 150 patients. In all cases the radiologist recorded the side of puncture, the number of passes needed, the number of vein punctures (one or two), whether the walls were opposed during puncture and any complications. For the last 80 patients the following information was also recorded: the distance from the skin to the internal jugular vein, the diameter of the vein with the Valsalva manoeuvre and the location of the vein relative to the carotid artery. All but three of the cannulations were performed by one of three radiologists, all of whom had at least 5 years of experience. Cannulation was successful in all of the patients, and the first pass was successful in 133 (88.7%). These results are better than those of blind placement techniques reported in the literature. The only complications were hematoma and carotid puncture, which both occurred in the same two patients (1.3%). There was no significant difference among the radiologists in the number of passes needed (one-way analysis of variance, p > 0.05). The number of passes was independent of anatomic factors, including depth from skin, vein diameter or relative location. However, significantly more passes were needed for left-side punctures than for right-side punctures (Student t-test, p < 0.05). Real-time ultrasound monitoring is superior to blind techniques in cannulation of the internal jugular vein because of its ease, accuracy and safety. Sonographic real-time monitoring minimizes the impact of anatomic factors on success and complication rates. It is a safe and efficacious approach that should be preferred in the placement of central lines.

  13. European Society of Hypertension position paper on ambulatory blood pressure monitoring.

    Science.gov (United States)

    O'Brien, Eoin; Parati, Gianfranco; Stergiou, George; Asmar, Roland; Beilin, Laurie; Bilo, Grzegorz; Clement, Denis; de la Sierra, Alejandro; de Leeuw, Peter; Dolan, Eamon; Fagard, Robert; Graves, John; Head, Geoffrey A; Imai, Yutaka; Kario, Kazuomi; Lurbe, Empar; Mallion, Jean-Michel; Mancia, Giuseppe; Mengden, Thomas; Myers, Martin; Ogedegbe, Gbenga; Ohkubo, Takayoshi; Omboni, Stefano; Palatini, Paolo; Redon, Josep; Ruilope, Luis M; Shennan, Andrew; Staessen, Jan A; vanMontfrans, Gert; Verdecchia, Paolo; Waeber, Bernard; Wang, Jiguang; Zanchetti, Alberto; Zhang, Yuqing

    2013-09-01

    Ambulatory blood pressure monitoring (ABPM) is being used increasingly in both clinical practice and hypertension research. Although there are many guidelines that emphasize the indications for ABPM, there is no comprehensive guideline dealing with all aspects of the technique. It was agreed at a consensus meeting on ABPM in Milan in 2011 that the 34 attendees should prepare a comprehensive position paper on the scientific evidence for ABPM.This position paper considers the historical background, the advantages and limitations of ABPM, the threshold levels for practice, and the cost-effectiveness of the technique. It examines the need for selecting an appropriate device, the accuracy of devices, the additional information and indices that ABPM devices may provide, and the software requirements.At a practical level, the paper details the requirements for using ABPM in clinical practice, editing considerations, the number of measurements required, and the circumstances, such as obesity and arrhythmias, when particular care needs to be taken when using ABPM.The clinical indications for ABPM, among which white-coat phenomena, masked hypertension, and nocturnal hypertension appear to be prominent, are outlined in detail along with special considerations that apply in certain clinical circumstances, such as childhood, the elderly and pregnancy, and in cardiovascular illness, examples being stroke and chronic renal disease, and the place of home measurement of blood pressure in relation to ABPM is appraised.The role of ABPM in research circumstances, such as pharmacological trials and in the prediction of outcome in epidemiological studies is examined and finally the implementation of ABPM in practice is considered in relation to the issue of reimbursement in different countries, the provision of the technique by primary care practices, hospital clinics and pharmacies, and the growing role of registries of ABPM in many countries.

  14. Development and clinical application of a patient-position monitoring system

    Science.gov (United States)

    Gerig, Lee H.; El-Hakim, Sabry F.; Szanto, Janos; Salhani, Doug; Girard, A.

    1994-10-01

    We have developed and clinically tested a computer vision system capable of real time monitoring of the position of an oncology (cancer) patient undergoing radiation therapy. The system is able to report variations in patient setup from day to day, as well as patient motion during an individual treatment. The system consists of two CCD cameras mounted in the treatment room and focused on the treatment unit isocenter. The cameras are interfaced to a PC via a two channel video board. Special targets, placed on the patient surface are automatically recognized and extracted by our 3D vision software. The three coordinates of each target are determined using a triangulation algorithm. System accuracy, stability and reproducibility were tested in the laboratory as well as in the radiation therapy room. Beside accuracy, the system must ensure the highest reliability and safety in the actual application environment. In this paper we also report on the results of clinical testing performed on a total of 23 patients having various treatment sites and techniques. The system in its present configuration is capable of measuring multiple targets placed on the patient surface during radiation therapy. In the clinical environment the system has an accuracy and repeatability of better than 0.5 mm in Cartesian space over extended periods (> 1 month). The system can measure and report patient position in less than 5 seconds. Clinically we have found that the system can easily and accurately detect patient motion during treatment as well as variations in patient setup from day to day. A brief description of the system and detailed analysis of its performance in the laboratory and in the clinic are presented.

  15. ANITA Air Monitoring on the International Space Station: Results Compared to Other Measurements

    Science.gov (United States)

    Honne, A.; Schumann-Olsen, H.; Kaspersen, K.; Limero, T.; Macatangay, A.; Mosebach, H.; Kampf, D.; Mudgett, P. D.; James, J. T.; Tan, G.; hide

    2009-01-01

    ANITA (Analysing Interferometer for Ambient Air) is a flight experiment precursor for a permanent continuous air quality monitoring system on the ISS (International Space Station). For the safety of the crew, ANITA can detect and quantify quasi-online and simultaneously 33 gas compounds in the air with ppm or sub-ppm detection limits. The autonomous measurement system is based on FTIR (Fourier Transform Infra-Red spectroscopy). The system represents a versatile air quality monitor, allowing for the first time the detection and monitoring of trace gas dynamics in a spacecraft atmosphere. ANITA operated on the ISS from September 2007 to August 2008. This paper summarizes the results of ANITA s air analyses with emphasis on comparisons to other measurements. The main basis of comparison is NASA s set of grab samples taken onboard the ISS and analysed on ground applying various GC-based (Gas Chromatography) systems.

  16. Detection of atmospheric nuclear explosions: the infrasound component of the International Monitoring System

    International Nuclear Information System (INIS)

    Christie, D.R.; Vivas Veloso, J.A.; Campus, P.; Bell, M.; Hoffmann, T.; Langlois, A.; Martysevich, P.; Demirovic, E.; Carvalho, J.

    2001-01-01

    The infrasound component of the International Monitoring System (IMS) for Comprehensive Nuclear-Test-Ban Treaty verification will consist of 60 array stations distributed as uniformly as possible over the surface of the globe. This network will be far larger and more sensitive than any other previously operated infrasound network. In this paper, we discuss the design and performance characteristics of this monitoring network and the current status of the site survey and installation programs. A brief review of significant developments in infrasound monitoring technology in the last few years is also presented along with a summary of the various areas where data from this unique global network is likely to be of value to the scientific community. (orig.) [de

  17. Direct internal dosimetry. A new way for routine incorporation monitoring of γ-emitting radionuclides

    International Nuclear Information System (INIS)

    Doerfel, H.

    1996-01-01

    The INDOS detector system offers the following advantages with respect to routine incorporation monitoring: The measurement is performed automatically and there is no need for trained staff. The measuring time is short and thus a relative large number of persons may be monitored with a relative high measuring frequency. First estimates of the individual effective dose equivalent rate are available immediately after the measurement. 1) The direct determination of the dose equivalent in principle is more precise than the conventional procedures for internal dosimetry, because (i) the retention of radionuclides in the body may be measured explicitly and (ii) the dependence of the dose equivalent on the body proportions is corrected implicitly. 2) The measuring procedure is comparable to the external dosimetry with respect to accuracy and lower limit of detection. Thus, the results of internal and external dosimetry can be summed up in an easy and reasonable manner. 3) The detector system can be installed in any building; it also can be installed as a mobile unit in a car or a container for long distance transportation by aircraft or train. 4) Last but not least, the cost for monitoring with INDOS is much lower than for the conventional monitoring procedures using whole body counters. (author)

  18. The role of internal forward models and proprioception in hand position estimation.

    Science.gov (United States)

    Yavari, Fatemeh; Towhidkhah, Farzad; Ahmadi-Pajouh, Mohammad-Ali; Darainy, Mohammad

    2015-09-01

    Our ability to properly move and react in different situations is largely dependent on our perception of our limbs' position. At least three sources - vision, proprioception, and internal forward models (FMs) - seem to contribute to this perception. To the best of our knowledge, the effect of each source has not been studied individually. Specifically, role of FM has been ignored in some previous studies. We hypothesized that FM has a critical role in subjects' perception which needs to be considered in the relevant studies to obtain more reliable results. Therefore, we designed an experiment with the goal of investigating FM and proprioception role in subjects' perception of their hand's position. Three groups of subjects were recruited in the study. Based on the experiment design, it was supposed that subjects in different groups relied on proprioception, FM, and both of them for estimating their unseen hand's position. Comparing the results of three groups revealed significant difference between their estimation' errors. FM provided minimum estimation error, while proprioception had a bias error in the tested region. Integrating proprioception with FM decreased this error. Integration of two Gaussian functions, fitted to the error distribution of FM and proprioception groups, was simulated and created a mean error value almost similar to the experimental observation. These results suggest that FM role needs to be considered when studying the perceived position of the limbs. This can lead to gain better insights into the mechanisms underlying the perception of our limbs' position which might have potential clinical and rehabilitation applications, e.g., in the postural control of elderly which are at high risk of falls and injury because of deterioration of their perception with age.

  19. Final implementation, commissioning, and performance of embedded collimator beam position monitors in the Large Hadron Collider

    Science.gov (United States)

    Valentino, Gianluca; Baud, Guillaume; Bruce, Roderik; Gasior, Marek; Mereghetti, Alessio; Mirarchi, Daniele; Olexa, Jakub; Redaelli, Stefano; Salvachua, Belen; Valloni, Alessandra; Wenninger, Jorg

    2017-08-01

    During Long Shutdown 1, 18 Large Hadron Collider (LHC) collimators were replaced with a new design, in which beam position monitor (BPM) pick-up buttons are embedded in the collimator jaws. The BPMs provide a direct measurement of the beam orbit at the collimators, and therefore can be used to align the collimators more quickly than using the standard technique which relies on feedback from beam losses. Online orbit measurements also allow for reducing operational margins in the collimation hierarchy placed specifically to cater for unknown orbit drifts, therefore decreasing the β* and increasing the luminosity reach of the LHC. In this paper, the results from the commissioning of the embedded BPMs in the LHC are presented. The data acquisition and control software architectures are reviewed. A comparison with the standard alignment technique is provided, together with a fill-to-fill analysis of the measured orbit in different machine modes, which will also be used to determine suitable beam interlocks for a tighter collimation hierarchy.

  20. Final implementation, commissioning, and performance of embedded collimator beam position monitors in the Large Hadron Collider

    Directory of Open Access Journals (Sweden)

    Gianluca Valentino

    2017-08-01

    Full Text Available During Long Shutdown 1, 18 Large Hadron Collider (LHC collimators were replaced with a new design, in which beam position monitor (BPM pick-up buttons are embedded in the collimator jaws. The BPMs provide a direct measurement of the beam orbit at the collimators, and therefore can be used to align the collimators more quickly than using the standard technique which relies on feedback from beam losses. Online orbit measurements also allow for reducing operational margins in the collimation hierarchy placed specifically to cater for unknown orbit drifts, therefore decreasing the β^{*} and increasing the luminosity reach of the LHC. In this paper, the results from the commissioning of the embedded BPMs in the LHC are presented. The data acquisition and control software architectures are reviewed. A comparison with the standard alignment technique is provided, together with a fill-to-fill analysis of the measured orbit in different machine modes, which will also be used to determine suitable beam interlocks for a tighter collimation hierarchy.

  1. 13th Workshop on Radiation Monitoring for the International Space Station - Final Program

    International Nuclear Information System (INIS)

    2008-01-01

    The Workshop on Radiation Monitoring for the International Space Station (WRMISS) has been held annually since 1996. The major purpose of WRMISS is to provide a forum for discussion of technical issues concerning radiation dosimetry aboard the International Space Station. This includes discussion of new results, improved instrumentation, detector calibration, and radiation environment and transport models. The goal of WRMISS is to enhance international efforts to provide the best information on the space radiation environment in low-Earth orbit and on the exposure of astronauts and cosmonauts in order to optimize the radiation safety of the ISS crew. During the 13 th Annual WRMISS, held in the Institute of Nuclear Physics (Krakow, Poland) on 8-10 September 2008, participants presented 47 lectures

  2. Calibration of an advanced photon source linac beam position monitor used for positron position measurement of a beam containing both positrons and electrons

    International Nuclear Information System (INIS)

    Sereno, Nicholas S.

    1998-01-01

    The Advanced Photon Source (APS) linac beam position monitors can be used to monitor the position of a beam containing both positrons and electrons. To accomplish this task, both the signal at the bunching frequency of 2856 MHz and the signal at 2x2856 MHz are acquired and processed for each stripline. The positron beam position is obtained by forming a linear combination of both 2856 and 5712 MHz signals for each stripline and then performing the standard difference over sum computation. The required linear combination of the 2856 and 5712 MHz signals depends on the electrical calibration of each stripline/cable combination. In this paper, the calibration constants for both 2856 MHz and 5712 MHz signals for each stripline are determined using a pure beam of electrons. The calibration constants are obtained by measuring the 2856 and 5712 MHz stripline signals at various electron beam currents and positions. Finally, the calibration constants measured using electrons are used to determine positron beam position for the mixed beam case

  3. Advances in seismic monitoring at Deception Island volcano (Antarctica since the International Polar Year

    Directory of Open Access Journals (Sweden)

    Enrique Carmona

    2014-06-01

    Full Text Available Deception Island is an active volcano located in the south Shetland Islands, Antarctica. It constitutes a natural laboratory to test geophysical instruments in extreme conditions, since they have to endure not only the Antarctic climate but also the volcanic environment. Deception is one of the most visited places in Antarctica, both by scientists and tourists, which emphasize the importance of volcano monitoring. Seismic monitoring has been going on since 1986 during austral summer surveys. The recorded data include volcano-tectonic earthquakes, long-period events and volcanic tremor, among others. The level of seismicity ranges from quiet periods to seismic crises (e.g. 1992-1993, 1999. Our group has been involved in volcano monitoring at Deception Island since 1994. Based on this experience, in recent years we have made the most of the opportunities of the International Polar Year 2007-2008 to introduce advances in seismic monitoring along four lines: (1 the improvement of the seismic network installed for seismic monitoring during the summer surveys; (2 the development and improvement of seismic arrays for the detection and characterization of seismo-volcanic signals; (3 the design of automated event recognition tools, to simplify the process of data interpretation; and (4 the deployment of permanent seismic stations. These advances help us to obtain more data of better quality, and therefore to improve our interpretation of the seismo-volcanic activity at Deception Island, which is a crucial step in terms of hazards assessment.

  4. Advancing internal erosion monitoring using seismic methods in field and laboratory studies

    Science.gov (United States)

    Parekh, Minal L.

    This dissertation presents research involving laboratory and field investigation of passive and active methods for monitoring and assessing earthen embankment infrastructure such as dams and levees. Internal erosion occurs as soil particles in an earthen structure migrate to an exit point under seepage forces. This process is a primary failure mode for dams and levees. Current dam and levee monitoring practices are not able to identify early stages of internal erosion, and often the result is loss of structure utility and costly repairs. This research contributes to innovations for detection and monitoring by studying internal erosion and monitoring through field experiments, laboratory experiments, and social and political framing. The field research in this dissertation included two studies (2009 and 2012) of a full-scale earthen embankment at the IJkdijk in the Netherlands. In both of these tests, internal erosion occurred as evidenced by seepage followed by sand traces and boils, and in 2009, eventual failure. With the benefit of arrays of closely spaced piezometers, pore pressure trends indicated internal erosion near the initiation time. Temporally and spatially dense pore water pressure measurements detected two pore water pressure transitions characteristic to the development of internal erosion, even in piezometers located away from the backward erosion activity. At the first transition, the backward erosion caused anomalous pressure decrease in piezometers, even under constant or increasing upstream water level. At the second transition, measurements stabilized as backward erosion extended further upstream of the piezometers, as shown in the 2009 test. The transitions provide an indication of the temporal development and the spatial extent of backward erosion. The 2012 IJkdijk test also included passive acoustic emissions (AE) monitoring. This study analyzed AE activity over the course of the 7-day test using a grid of geophones installed on the

  5. Communications and Positioning by Satelhte in the International Road Transport System

    Directory of Open Access Journals (Sweden)

    Draško Marin

    2012-10-01

    Full Text Available This article describes the basic technology of satellite .I'Stemsrelated to the geostationary satellites particular(v with regardto the .\\'Stem of satellites in the European network ofEUTELSAT (European Telecommunications Satellite Organizationcovering Europe, North Africa and part of the MiddleEast.This enables positioning of vehicles in the internationalroad transport system in the territory which has been covered bythe satellite signal.The EUTELTRACS system within the EUTELSAT organizationenables not only positioning with preciseness ofabout 300 m, but also two-way communications between vehiclesand company headquarters, which is an advantage comparedto the other positioning systems.EUTELTRACS service belongs to the land mobile satelliteservices with secondary status (it must not impose any interferenceto other radio-communication services and cannot claimprotection from other services.The use of frequency bands is for the up-links 14.0-14.25GHz, and for the down-links 10.25-11.20 GHz, 11.45-11.70GHz and 12.50-12.75 GHz.The EUTELTRACS system provides services by means ofOmniTRACS terminals and CEPT (European Conference ofPostal and Telecommunications Administrations administrationsissue type approvals, designating the terminal markingand make decisions regarding free circulation of terminals inconformity with their national regulations.The OmniTRACS terminal.l'stem has been specially presentedas well as the fixed part of EUTELTRACS .\\'Stem withthe satellite segment.Every transport company has been considered as a subscriberto an authorised EUTELTRACS service provider.The service for tracing trucks in the international trafficthroughout Europe and Middle East can be fully expressed byincluding the stronger transport companies (more than 10trucks which can establish the transport more rationallythrough EUTELTRACS service.The implementation of the EUTELTRACS service hasbeen imposed on the Croatian companies, whose internationaltransport could

  6. Disarmament and control of nuclear weapons: Russian positions and their national and international determining factors

    International Nuclear Information System (INIS)

    Facon, Isabelle

    2009-01-01

    In a context where Russia seems to come back to some key principles which guided its international action since the end of Cold War, and relationships between Russia and the USA have been degraded since the US intervention in Iraq (2003), the author examines whether these new Russian postures also concern strategic disarmament, whether Russia is loosing its interest in traditional arrangements of strategic stability, and what are Moscow's priorities within the perspective of expiry of the START 1 Treaty. Thus, the author discusses the role of nuclear weapons in the Russian defence policy, outlines the paradoxes of Russian negotiation positions in the fields of disarmament and arms control, and highlights indirect approaches adopted by Russia on these issues

  7. Positioning Space Solar Power (SSP) as the Next Logical Step after the International Space Station (ISS)

    Science.gov (United States)

    Charania, A.

    2002-01-01

    At the end of the first decade of the 21st century, the International Space Station (ISS) will stand as a testament of the engineering capabilities of the international community. The choices for the next logical step for this community remain vast and conflicting: a Mars mission, moon colonization, Space Solar Power (SSP), etc. This examination focuses on positioning SSP as one such candidate for consideration. A marketing roadmap is presented that reveals the potential benefits of SSP to both the space community and the global populace at large. Recognizing that scientific efficiency itself has no constituency large enough to persuade entities to outlay funds for such projects, a holistic approach is taken to positioning SSP. This includes the scientific, engineering, exploratory, economic, political, and development capabilities of the system. SSP can be seen as both space exploration related and a resource project for undeveloped nations. Coupling these two non-traditional areas yields a broader constituency for the project that each one alone could generate. Space exploration is many times seen as irrelevant to the condition of the populace of the planet from which the money comes for such projects. When in this new century, billions of people on the planet still have never made a phone call or even have access to clean water, the origins of this skepticism can be understandable. An area of concern is the problem of not living up to the claims of overeager program marketers. Just as the ISS may never live up to the claims of its advocates in terms of space research, any SSP program must be careful in not promising utopian global solutions to any future energy starved world. Technically, SSP is a very difficult problem, even harder than creating the ISS, yet the promise it can hold for both space exploration and Earth development can lead to a renaissance of the relevance of space to the lives of the citizens of the world.

  8. Correlative Studies in Clinical Trials: A Position Statement From the International Thyroid Oncology Group.

    Science.gov (United States)

    Bible, Keith C; Cote, Gilbert J; Demeure, Michael J; Elisei, Rossella; Jhiang, Sissy; Ringel, Matthew D

    2015-12-01

    Patients with progressive thyroid cancer in distant metastatic sites represent a population with a need for new therapeutic options. Aspiring to improve the treatment of such patients, the objective of this position statement from the International Thyroid Oncology Group (ITOG) is to clarify the importance of incorporating high-quality correlative studies into clinical trials. ITOG was formed to develop and support high-quality multicenter and multidisciplinary clinical trials for patients with aggressive forms of thyroid cancer. The Correlative Sciences Committee of the ITOG focuses on the quality and types of correlative studies included in ITOG-associated clinical trials. This document represents expert consensus from ITOG regarding this issue based on extensive collective experience in clinical and translational trials informed by basic science. The Correlative Studies Committee identified an international writing group representative of diverse specialties, including basic sciences. Drafts were reviewed by all members of the writing group, the larger committee, and the ITOG board. After consideration of all comments by the writing group and modification of the document, the final document was then approved by the authors and the ITOG board. High-quality correlative studies, which include variety in the types of correlates, should be intrinsic to the design of thyroid cancer clinical trials to offer the best opportunity for each study to advance treatment for patients with advanced and progressive thyroid cancer.

  9. POSITIVE INTERACTION IN AN INCLUSIVE EDUCATION: MANIFESTATION OF THE INTERNATIONAL CHILD DEVELOPMENT PROGRAMME (ICDP

    Directory of Open Access Journals (Sweden)

    Farid Alamdar oglu Suleymanov

    2016-01-01

    Full Text Available Abstract. Kind relation between a child and caregiver (parent, teacher is a critically vital point for psychological development of children. Better relations also contribute to the child’s healthy growth and intellectual, social and emotional development. Fundamental caregiving skills function as particularly important contribution to the quality and effectiveness all caregiving. In order to facilitate full development of a child, it is important that the caregiver have a positive conception of the child. In other words, a caregiver should regard a child as a person with potential for development. From this perspective International Child Development Programme (ICDP functions as a resource-based communication and mediation approach which trains caregiver to develop a positive conception of their children and gain wider and deeper insight and confidence about their responsibilities and roles. Based on the themes of ICDP, the current research studied the quality of positive interaction between teacher assistants (TA and children with special needs (CSN in an inclusive primary education in Azerbaijan. The findings suggest that some elements of ICDP approach exist in teacher-student interaction. However, these interaction patterns are unprofessional and need development through relevant in-service trainings. Methods. In this research a case study design of qualitative research was used to investigate teacher assistants’ (TA understanding of positive attitude and how they establish positive relations with the students with special needs whom they take care of. As for the research method, the case study will adopt triangulation, a multiple methods of data collection which will include interview and observation to extend confidence in its validity and improve the quality of the data and accuracy of the findings. Results. Comparative analyses of triangulation data demonstrate that TAs’ performance within the context of teacher-student positive

  10. First experiences of beam presence detection based on dedicated beam position monitors

    International Nuclear Information System (INIS)

    Jalal, A.; Gabourin, S.; Gasior, M.; Todd, B.

    2012-01-01

    High intensity particle beam injection into the LHC is only permitted when a low intensity pilot beam is already circulating in the LHC. This requirement addresses some of the risks associated with high intensity injection, and is enforced by a so-called Beam Presence Flag (BPF) system which is part of the interlock chain between the LHC and its injector complex. For the 2010 LHC run, the detection of the presence of this pilot beam was implemented using the LHC Fast Beam Current Transformer (FBCT) system. However, the primary function of the FBCTs, that is reliable measurement of beam currents, did not allow the BPF system to satisfy all quality requirements of the LHC Machine Protection System (MPS). Safety requirements associated with high intensity injections triggered the development of a dedicated system, based on Beam Position Monitors (BPM). This system was meant to work first in parallel with the FBCT BPF system and eventually replace it. At the end of 2010 and in 2011, this new BPF implementation based on BPMs was designed, built, tested and deployed. This paper reviews both the FBCT and BPM implementation of the BPF system, outlining the changes during the transition period. The paper briefly describes the testing methods, focuses on the results obtained from the tests performed during the end of 2010 LHC run and shows the changes made for the BPM BPF system deployment in LHC in 2011. Whilst the system has been proved to work with a threshold of 6*10 8 charges, it has been implemented with a threshold of 2*10 9 charges to protect the LHC. (authors)

  11. MONITORING OF INTERNATIONAL DONOR ASSISTANCE IN THE CONTEXT OF THE DEVELOPMENT OF AMALGAMATED TERRITORIAL COMMUNITIES

    Directory of Open Access Journals (Sweden)

    Elina Boichenko

    2017-12-01

    Full Text Available The research is conducted within the framework of the joint project of the F. Ebert Foundation (Germany and the Institute of Economic and Legal Studies of the National Academy of Sciences of Ukraine (Ukraine “The Experience of the Association of Territorial Communities in Eastern Ukraine: Economic and Legal Aspects”. The subject of the study is the theoretical, methodological, and practical aspects of monitoring international donor assistance in the context of the development of amalgamated territorial communities (ATC based on the example of Bilokurakyne and Novopskov ATC. Methodology. The system approach (in substantiating the directions of monitoring and established procedures for monitoring each component of the life of amalgamated territorial communities, logical generalization (in determining the state of development of amalgamated territorial communities, method of absolute, relative, and mean values, analysis of the dynamics series and structural shifts (in determining the dominant trends in the formation and development of ATC, method of economic analysis and synthesis (in determining the content of the monitoring, method of comparison (when the violations in the process of ATC, graphical method (the construction algorithm combined operation and development of local communities imaging method (for presenting the results of the total amount of international aid to ATC are used in the work. The purpose of the research is to develop theoretical, methodological, and practical approaches to the monitoring of international donor assistance in the context of the development of amalgamated territorial communities. The article suggests using monitoring as the most effective tool for controlling economic and social phenomena and processes. The authorial scheme for constructing a procedure for the monitoring of functioning and development of amalgamated territorial communities is developed. The monitoring of international donor support of the

  12. A prospective international observational prevalence study on prone positioning of ARDS patients: the APRONET (ARDS Prone Position Network) study

    NARCIS (Netherlands)

    Guérin, C.; Beuret, P.; Constantin, J. M.; Bellani, G.; Garcia-Olivares, P.; Roca, O.; Meertens, J. H.; Maia, P. Azevedo; Becher, T.; Peterson, J.; Larsson, A.; Gurjar, M.; Hajjej, Z.; Kovari, F.; Assiri, A. H.; Mainas, E.; Hasan, M. S.; Morocho-Tutillo, D. R.; Baboi, L.; Chrétien, J. M.; François, G.; Ayzac, L.; Chen, L.; Brochard, L.; Mercat, A.; Hajjej, Zied; Sellami, Walid; Ferjani, M.; Gurjar, Mohan; Assiri, Amer; Al Bshabshe, Ali; Almekhlafi, Ghaleb; Mandourah, Yasser; Hasan, Mohd Shahnaz; Rai, Vineya; Marzida, M.; Corcoles Gonzalez, Virgilio; Sanchez Iniesta, Rafael; Garcia, Pablo; Garcia-Montesinos de La Peña, Manuel; Garcia Herrera, Adriana; Roca, Oriol; Garcia-de-Acilu, Marina; Masclans Enviz, Joan Ramon; Mancebo, Jordi; Heili, Sarah; Artigas Raventos, Antonio; Blanch Torra, Lluís; Roche-Campo, Ferran; Rialp, Gemma; Forteza, Catalina; Berrazueta, Ana; Martinez, Esther; Penuelas, Oscar; Jara-Rubio, Ruben; Mallat, Jihad; Thevenin, D.; Zogheib, Elie; Mercat, Alain; Levrat, Albrice; Porot, Veronique; Bedock, B.; Grech, Ludovic; Plantefeve, Gaetan; Badie, Julio; Besch, Guillaume; Pili-Floury, Sébastien; Guisset, Olivier; Robine, Adrien; Prat, Gwenael; Doise, Jean-Marc; Badet, Michel; Thouret, J. M.; Just, Bernard; Perbet, Sébastien; Lautrette, Alexandre; Souweine, B.; Chabanne, Russell; Danguy des Déserts, Marc; Rigaud, Jean-Philippe; Marchalot, Antoine; Rigaud, J. P.; Bele, Nicolas; Beague, Sébastien; Hours, Sandrine; Marque, Sophie; Durand, Michel; Payen, J. F.; Stoclin, Annabelle; Gaffinel, Alain; Winer, Arnaud; Chudeau, Nicolas; Tirot, Patrice; Thyrault, Martial; Paulet, Rémi; Thyrault, M.; Aubrun, Frederic; Guerin, Claude; Floccard, Bernard; Rimmele, T.; Argaud, Laurent; Hernu, Romain; Crozon Clauzel, Jullien; Wey, Pierre-François; Bourdin, Gael; Pommier, C.; Cueuille, Nadège; de Varax, N. N.; Marchi, Elisa; Papazian, L.; Jochmans, Sebastien; Monchi, M.; Jaber, Samir; de Jong, Audrey; Moulaire, Valerie; Capron, Matthieu; Jarrige, L.; Barberet, Guillaume; Lakhal, Karim; Rozec, B.; Dellamonica, Jean; Robert, Alexandre; Bernardin, G.; Danin, Pierre-Eric; Raucoules, M.; Runge, Isabelle; Foucrier, Arnaud; Hamada, Sophie; Tesniere, Antoine; Fromentin, Mélanie; Samama, C. M.; Mira, Jean-Paul; Diehl, Jean-Luc; Mekontso Dessap, Armand; Arbelot, Charlotte; Demoule, Alexandre; Roche, Anne; Similowski, T.; Ricard, Jean-Damien; Gaudry, Stéphane; Dreyfuss, D.; de Montmolin, Etienne; Da Silva, Daniel; Verdiere, B.; Ardisson, Fanny; Lemiale, Virginie; Azoulay, Elie; Bruel, Cédric; Tiercelet, Kelly; Fartoukh, Muriel; Voiriot, Guillaume; Hoffmann, Clement; Leclerc, T.; Thille, Arnaud; Robert, Réné; Beuret, Pascal; Beduneau, Gaëtan; Beuzelin, Marion; Tamion, F.; Morel, Jérôme; Tremblay, Aymeric; Molliex, S.; Amal, Jean-Michel; Meaudre, Eric; Goutorbe, Philippe; Laffon, Marc; Gros, Antoine; Nica, Alexandru; Barjon, Genevieve; Dahyot-Fizelier, Claire; Imzi, Nadia; Gally, Josette; Real, N. N.; Sauneuf, Bertrand; Souloy, Xavier; Girbes, Armand; Tuinman, Pieter Roel; Schultz, Marcus; Winters, Tineke; Mijzen, Lisa; Roekaerts, P. M. H. J.; Vermeijden, Wytze; Beishuizen, Albertus; Trof, R.; Corsten, Stijn; Kesecioglu, Jozef; Meertens, John; Dieperink, Wim; Pickers, Peter; Roovers, Noortje; Maia, Paulo; Duque, Melanie; Rua, Fernando; Pereira de Figueired, António Manuel; Ramos, Armindo; Fragoso, Elsa; Azevedo, Pilar; Gouveia, Joao; Costa E Silva, Zélia; Silva, Goncalo; Chaves, Susana; Nobrega, J. J.; Lopes, Luís; Valerio, Bernardino; Araujo, Ana Carolina; de Freitas, Paulo Telles; Bouw, Maria Jose; Melao, Maria; Granja, C.; Marcal, Paulo; Fernandes, Antero; Joao, Gonçalves Pereira; Maia, Dionísio Faria; Spadaro, Savino; Volta, Carlo Alberto; Bellani, Giacomo; Citerio, G.; Mauri, Tommaso; Alban, Laura; Pesenti, A.; Mistraletti, Giovanni; Formenti, Paolo; Tommasino, C.; Tardini, Francesca; Fumagalli, R.; Colombo, Riccardo; Fossali, Tommaso; Catena, E.; Todeschini, Manuel; Gnesin, Paolo; Cracchiolo, Andrea Neville; Palma, Daniela; Tetamo, R.; Albiero, Daniela; Costantini, Elena; Raimondi, F.; Coppadoro, Andrea; Vascotto, Ettore; Lusenti, F.; Becher, Tobias; Schädler, Dirk; Weiler, N.; Karagiannidis, Christian; Petersson, Johan; Konrad, D.; Kawati, Rafael; Wessbergh, Joanna; Valtysson, J.; Rockstroh, Matthias; Borgstrom, Sten; Larsson, Niklas; Thunberg, J.; Camsooksai, Julie; Briggs, N. N.; Kovari, Ferenc; Cuesta, J.; Anwar, Sibs; O'Brien, B.; Barberis, Luigi; Sturman, J.; Mainas, Efstratios; Karatzas, S.; Piza, Petr; Sottiaux, Thierry; Adam, J. F.; Gawda, Ryszard; Gawor, Maen; Alqdah, M.; Cohen, D.; Brochard, Laurent; Baker, A.; Ñamendys-Silva, Silvio Antonio; Garcia-Guillen, Francisco Javier; Morocho Tutillo, Diego Rolando; Jibaja Vega, Manuel; Zakalik, Graciela; Pagella, Gonzalo; Marengo, J.

    2018-01-01

    While prone positioning (PP) has been shown to improve patient survival in moderate to severe acute respiratory distress syndrome (ARDS) patients, the rate of application of PP in clinical practice still appears low. This study aimed to determine the prevalence of use of PP in ARDS patients (primary

  13. Optimization of internal contamination monitoring programmes by studying uncertainties linked to dosimetric assessment

    International Nuclear Information System (INIS)

    Davesne, Estelle

    2010-01-01

    To optimise the protection of workers against ionizing radiations, the International Commission on Radiological Protection recommends the use of dose constraint and limits. To verify the compliance of the means of protection with these values when a risk of internal contamination exists, monitoring programmes formed of periodic bioassay measurements are performed. However, uncertainty in the dose evaluation arises from the variability of the activity measurement and from the incomplete knowledge of the exposure conditions. This uncertainty was taken into account by means of classical, Bayesian and possibilist statistics. The developed methodology was applied to the evaluation of the potential exposure during nuclear fuel preparation or mining; and to the analysis of the monitoring programme of workers purifying plutonium in AREVA NC La Hague reprocessing plant. From the measurement decision threshold, the minimum dose detectable (MDD) by the programme with a given confidence level can be calculated through the software OPSCI. It is shown to be a useful support in the optimisation of monitoring programmes when seeking a compromise between their sensitivity and their costs. (author)

  14. Returnees, Student-Migrants and Second Chance Learners: Case Studies of Positional and Transformative Outcomes of Australian International Education

    Science.gov (United States)

    Robertson, Shanthi; Hoare, Lynnel; Harwood, Aramiha

    2011-01-01

    There is a clear need for new research into the work and life outcomes for graduates of Australian international education. Drawing upon divergent post-study transitions, this article aims to present a multi-faceted, qualitative foundation for the consideration of both positional and transformative impacts of international education on graduates'…

  15. Internal seismological stations for monitoring a comprehensive test ban treaty test ban treaty

    International Nuclear Information System (INIS)

    Dahlman, O.; Israelson, H.

    1980-06-01

    Verification of the compliance with a comprehensive test ban on nuclear explosions is expected to be carried out by a seismological verification system of some fifty globally distributed teleseismic stations designed to monitor underground explosions at large distances (beyond 2000 km). The internal stations, which are intended to operate at much shorter distances, have however also been discussed. Such internal stations would be set up in the USSR and in the US and possibly also in the UK. Estimates partaining to currently used detection techniques (P waves) indicate that a limited number (less than 30) of such stations would not improve significantly upon the detection capability that a global network of stations would have throughout the territories of the US and the USSR. Observations in certain areas in eastern North America indicate that Lg-waves would be more suitable for detection purposes than would P-waves. Internal stations would provide a substantial lowering of detection threshold. Firm conclusions on this point have however to await further studies on Lg-waves. Internal stations would probably provide supplementary identification at short distances. Such data could contribute to more confident identification of seismic events detected by a global network and thereby reduce the risk for misinterpreting earthquakes as clandestine nuclear explosions. According to the estimated detection capabilities in this paper 10 internal stations would not improve significantly upon the detection capability that a global network would have in the US and the USSR. They might however serve an essential political purpose. (author)

  16. General guidelines for the assessment of internal dose from monitoring data: Progress of the IDEAS project

    International Nuclear Information System (INIS)

    Doerfel, H.; Andrasi, A.; Bailey, M.; Blanchardon, E.; Cruz-Suarez, R.; Berkovski, V.; Castellani, C. M.; Hurtgenv, C.; Leguen, B.; Malatova, I.; Marsh, J.; Stather, J.; Zeger, J.

    2007-01-01

    In recent major international intercomparison exercises on intake and internal dose assessments from monitoring data, the results calculated by different participants varied significantly. Based on this experience the need for harmonisation of the procedures has been formulated within an EU 5. Framework Programme research project. The aim of the project, IDEAS, is to develop general guidelines for standardising assessments of intakes and internal doses. The IDEAS project started in October 2001 and ended in June 2005. The project is closely related to some goals of the work of Committee 2 of the ICRP and since 2003 there has been close cooperation between the two groups. To ensure that the guidelines are applicable to a wide range of practical situations, the first step was to compile a database of well-documented cases of internal contamination. In parallel, an improved version of an existing software package was developed and distributed to the partners for further use. A large number of cases from the database was evaluated independently by the partners and the results reviewed. Based on these evaluations, guidelines were drafted and discussed with dosimetry professionals from around the world by means of a virtual workshop on the Internet early in 2004. The guidelines have been revised and refined on the basis of the experiences and discussions in this virtual workshop. The general philosophy of the Guidelines is presented here, focusing on the principles of harmonisation, optimisation and proportionality. Finally, the proposed Levels of Task to structure the approach of internal dose evaluation are reported. (authors)

  17. Perceptions of growth monitoring and promotion among an international panel of district medical officers.

    Science.gov (United States)

    Roberfroid, Dominique; Lefèvre, Pierre; Hoerée, Tom; Kolsteren, Patrick

    2005-09-01

    The growth chart has been proposed as an educational tool to make the child's growth visible to both health workers and caregivers and to enhance communication between them. In the case of growth faltering, this would trigger timely corrective measures. Although the relevance of growth monitoring and promotion (GMP) has often been questioned in the literature, opinions of District Medical Officers responsible for local implementation of GMP are unknown. The aim of this qualitative research was to explore the perceptions and difficulties of an international panel of District Medical Officers regarding GMP. As an exploratory study, in-depth interviews of an international panel of District Medical Officers (n=19) were conducted. Data were coded using the QSR Nudist 5.0 software. A discrepancy between intended purposes and practice of GMP was detected at two levels. First, lack of participation of care-givers was reported. Second, the District Medical Officers expressed a restrictive interpretation of the concept of growth monitoring. The communication with parents was never reported as a means or a result of GMP, neither as an evaluation criterion of programme efficiency. The growth chart was mainly considered a tool intended to be used by health services for the purpose of diagnosis. This two-fold discrepancy between the intention of international policy-planners and practice of local programme implementers could be a crucial factor affecting the performance of GMP. More emphasis should be put on social communication and involvement of caregivers.

  18. [Position of health at international relations. Part II. Organizational dimensions of health].

    Science.gov (United States)

    Cianciara, Dorota; Wysocki, Mirosław J

    2011-01-01

    The aim of this article was: (1) the analysis of some concepts and definitions related with "set up of health", used in UN international arrangements; (2) an attempt to explain the evolution of organizational dimensions of health at worldwide agenda. The following organizational dimensions of health were discussed: (a) health for all, (b) health promotion, intersectoral and multisectoral actions, health in all policies, (c) health development, health as an element of human development, (d) investment for health, (e) health diplomacy and (f) mainstreaming of health. The analysis was based on World Health Assembly and UN General Assembly resolutions as well as supranational reports and statements available through conventional channels, not grey literature. It is apparent that some of notions are not in common use in Poland, some seems to be unknown. It was argued that some general and discreet thoughts and statements concerning organizational aspects of health were expressed in the preamble of WHO Constitution. Nevertheless they are not comparable with later propositions and proceedings. The first modern concepts and notions related as process were developed at late seventies. They originated from efforts to realize a vision of health for all and formulate national policies, strategies and plans of action for attaining this goal. The turning point was in 1981, when WHA adopted Global Strategy for Heath for All by the Year 2000. Since then one can observe considerable progress and new concepts came into existence, more and more precise and better reflecting the sense of health actions. The evolution of organizational dimensions of health was described in the context of brand positioning. It was assumed that first step of positioning was concentrated on structural dimensions of health. That served to awareness raise, attitudes change and motivation to action. That made a foundation to the next step--positioning based on process approach to health. Among others the

  19. Quality in cytopathology: an analysis of the internal quality monitoring indicators of the Instituto Nacional de Câncer

    Directory of Open Access Journals (Sweden)

    Mario Lucio C. Araujo Jr

    2015-04-01

    Full Text Available Introduction: Quality control programs are required to ensure the effectiveness of Pap smear, which still remain a key strategy for control of cervical cancer worldwide. Objective: This study was based on the retrospective and quantitative analysis of the post-analytical phase indicators from the internal quality monitoring (IQM program for cytopathology laboratories, such as: positivity rate, atypical squamous cell (ASC/satisfactory exams ratio, ASC/abnormal test results ratio, ASC/squamous intraepithelial lesions (SIL ratio, percentage of tests compatible with high-grade squamous intraepithelial lesion (HSIL, and total of false negative. Materials and methods: The information was extracted from the computerized system of the Section for Integrated Technology in Cytopathology (Seção Integrada de Tecnologia em Citopatologia [SITEC], a reference institution for cancer cytopathology, from July 2013 to June 2014. From a total of 156,888 Pap smears, 157,454 were considered satisfactory for indicator analysis and 566 were excluded because they were considered unsatisfactory and/or rejected for analysis. The data was organized in tables using Microsoft Excel 2010 software, and categorized as indicators. Results: The averages for the indicators were: 7.2% for positivity rate, 56.9 for ASC/abnormal test ratio, 4.1 for ASC/satisfactory tests ratio, 1.4 for ASC/SIL ratio, 0.6% percentage for tests compatible with HSIL, and 2.1% for false-negative rate. Conclusion: The results show that an Internal Quality Monitoring Program is essencial to ensure quality for cytopathology laboratories, and a randomized review of at least 10% of the negative exams, as recommended by the Brazilian Ministry of Health/Instituto Nacional de Câncer (INCA, since is an effective method, especially for large laboratories.

  20. Vibro-acoustic condition monitoring of Internal Combustion Engines: A critical review of existing techniques

    Science.gov (United States)

    Delvecchio, S.; Bonfiglio, P.; Pompoli, F.

    2018-01-01

    This paper deals with the state-of-the-art strategies and techniques based on vibro-acoustic signals that can monitor and diagnose malfunctions in Internal Combustion Engines (ICEs) under both test bench and vehicle operating conditions. Over recent years, several authors have summarized what is known in critical reviews mainly focused on reciprocating machines in general or on specific signal processing techniques: no attempts to deal with IC engine condition monitoring have been made. This paper first gives a brief summary of the generation of sound and vibration in ICEs in order to place further discussion on fault vibro-acoustic diagnosis in context. An overview of the monitoring and diagnostic techniques described in literature using both vibration and acoustic signals is also provided. Different faulty conditions are described which affect combustion, mechanics and the aerodynamics of ICEs. The importance of measuring acoustic signals, as opposed to vibration signals, is due since the former seem to be more suitable for implementation on on-board monitoring systems in view of their non-intrusive behaviour, capability in simultaneously capturing signatures from several mechanical components and because of the possibility of detecting faults affecting airborne transmission paths. In view of the recent needs of the industry to (-) optimize component structural durability adopting long-life cycles, (-) verify the engine final status at the end of the assembly line and (-) reduce the maintenance costs monitoring the ICE life during vehicle operations, monitoring and diagnosing system requests are continuously growing up. The present review can be considered a useful guideline for test engineers in understanding which types of fault can be diagnosed by using vibro-acoustic signals in sufficient time in both test bench and operating conditions and which transducer and signal processing technique (of which the essential background theory is here reported) could be

  1. Development of a Millimeter-Wave Beam Position and Profile Monitor for Transmission Efficiency Improvement in an ECRH System

    Directory of Open Access Journals (Sweden)

    Shimozuma T.

    2015-01-01

    Full Text Available In a high power Electron Cyclotron Resonance Heating (ECRH system, a long-distance and low-loss transmission system is required to realize effective heating of nuclear fusion-relevant plasmas. A millimeter-wave beam position and profile monitor, which can be used in a high-power, evacuated, and cooled transmission line, is proposed, designed, manufactured, and tested. The beam monitor consists of a reflector, Peltier-device array and a heat-sink. It was tested using simulated electric heater power or gyrotron output power. The data obtained from the monitor were well agreed with the heat source position and profile. The methods of data analysis and mode-content analysis of a propagating millimeter-wave in the corrugated wave-guide are proposed.

  2. 3rd International Conference on Condition Monitoring of Machinery in Non-Stationary Operations

    CERN Document Server

    Rubini, Riccardo; D'Elia, Gianluca; Cocconcelli, Marco; Chaari, Fakher; Zimroz, Radoslaw; Bartelmus, Walter; Haddar, Mohamed

    2014-01-01

    This book presents the processings of the third edition of the Condition Monitoring of Machinery in Non-Stationary Operations (CMMNO13) which was held in Ferrara, Italy. This yearly event merges an international community of researchers who met – in 2011 in Wroclaw (Poland) and in 2012 in Hammamet (Tunisia) – to discuss issues of diagnostics of rotating machines operating in complex motion and/or load conditions. The growing interest of the industrial world on the topics covered by the CMMNO13 involves the fields of packaging, automotive, agricultural, mining, processing and wind machines in addition to that of the systems for data acquisition.The participation of speakers and visitors from industry makes the event an opportunity for immediate assessment of the potential applications of advanced methodologies for the signal analysis. Signals acquired from machines often contain contributions from several different components as well as noise. Therefore, the major challenge of condition monitoring is to po...

  3. Health monitoring and disease prevention at the Zebrafish International Resource Center.

    Science.gov (United States)

    Varga, Z M; Murray, K N

    2016-01-01

    In this chapter we review the components of the fish health program at the Zebrafish International Resource Center. We describe health-monitoring strategies to assess individual and colony health, practices to prevent the spread of pathogens within the fish colony, and a biosecurity program designed to prevent entry of new fish pathogens. While this program is designed for a facility on a recirculating water system with expectations of high volumes of import and export, many of the components can be directly applied or modified for application in facilities of different sizes and with other programmatic goals. Copyright © 2016 Elsevier Inc. All rights reserved.

  4. The CRRES IDM spacecraft experiment for insulator discharge pulses. [Internal Discharge Monitor

    Science.gov (United States)

    Frederickson, A. R.; Mullen, E. G.; Kerns, K. J.; Robinson, P. A.; Holeman, E. G.

    1993-01-01

    The Internal Discharge Monitor (IDM) is designed to observe electrical pulses from common electrical insulators in space service. The characteristics of the instrument are described. The IDM was flown on the Combined Release and Radiation Effects Satellite (CRRES). The sixteen insulator samples included G10 circuit boards, FR4 and PTFE fiberglass circuit boards, FEP Teflon, alumina, and wires with common insulations. The samples are fully enclosed, mutually isolated, and space radiation penetrates 0.02 cm of aluminum before striking the samples. Published data in the literature provides a simple method for determining the flux of penetrating electrons. The pulse rate is compared to the penetrating flux of electrons.

  5. International Association for Hospice and Palliative Care Position Statement: Euthanasia and Physician-Assisted Suicide

    Science.gov (United States)

    Woodruff, Roger; Pettus, Katherine; Downing, Julia; Buitrago, Rosa; Munyoro, Esther; Venkateswaran, Chitra; Bhatnagar, Sushma; Radbruch, Lukas

    2017-01-01

    Abstract Background: Reports about regulations and laws on Euthanasia and Physician Assisted Suicide (PAS) are becoming increasingly common in the media. Many groups have expressed opposition to euthanasia and PAS while those in favor argue that severely chronically ill and debilitated patients have a right to control the timing and manner of their death. Others argue that both PAS and euthanasia are ethically legitimate in rare and exceptional cases. Given that these discussions as well as the new and proposed laws and regulations may have a powerful impact on patients, caregivers, and health care providers, the International Association for Hospice and Palliative Care (IAHPC) has prepared this statement. Purpose: To describe the position of the IAHPC regarding Euthanasia and PAS. Method: The IAHPC formed a working group (WG) of seven board members and two staff officers who volunteered to participate in this process. An online search was performed using the terms “position statement”, “euthanasia” “assisted suicide” “PAS” to identify existing position statements from health professional organizations. Only statements from national or pan-national associations were included. Statements from seven general medical and nursing associations and statements from seven palliative care organizations were identified. A working document including a summary of the different position statements was prepared and based on these, an initial draft was prepared. Online discussions among the members of the WG took place for a period of three months. The differences were reconciled by email discussions. The resulting draft was shared with the full board. Additional comments and suggestions were incorporated. This document represents the final version approved by the IAHPC Board of Directors. Result: IAHPC believes that no country or state should consider the legalization of euthanasia or PAS until it ensures universal access to palliative care services and to

  6. International Association for Hospice and Palliative Care Position Statement: Euthanasia and Physician-Assisted Suicide.

    Science.gov (United States)

    De Lima, Liliana; Woodruff, Roger; Pettus, Katherine; Downing, Julia; Buitrago, Rosa; Munyoro, Esther; Venkateswaran, Chitra; Bhatnagar, Sushma; Radbruch, Lukas

    2017-01-01

    Reports about regulations and laws on Euthanasia and Physician Assisted Suicide (PAS) are becoming increasingly common in the media. Many groups have expressed opposition to euthanasia and PAS while those in favor argue that severely chronically ill and debilitated patients have a right to control the timing and manner of their death. Others argue that both PAS and euthanasia are ethically legitimate in rare and exceptional cases. Given that these discussions as well as the new and proposed laws and regulations may have a powerful impact on patients, caregivers, and health care providers, the International Association for Hospice and Palliative Care (IAHPC) has prepared this statement. To describe the position of the IAHPC regarding Euthanasia and PAS. The IAHPC formed a working group (WG) of seven board members and two staff officers who volunteered to participate in this process. An online search was performed using the terms "position statement", "euthanasia" "assisted suicide" "PAS" to identify existing position statements from health professional organizations. Only statements from national or pan-national associations were included. Statements from seven general medical and nursing associations and statements from seven palliative care organizations were identified. A working document including a summary of the different position statements was prepared and based on these, an initial draft was prepared. Online discussions among the members of the WG took place for a period of three months. The differences were reconciled by email discussions. The resulting draft was shared with the full board. Additional comments and suggestions were incorporated. This document represents the final version approved by the IAHPC Board of Directors. IAHPC believes that no country or state should consider the legalization of euthanasia or PAS until it ensures universal access to palliative care services and to appropriate medications, including opioids for pain and dyspnea. In

  7. TRIGA control rod position and reactivity transient Monitoring by Neural Networks

    International Nuclear Information System (INIS)

    Rosa, R.; Palomba, M.; Sepielli, M.

    2008-01-01

    Plant sensors drift or malfunction and operator actions in nuclear reactor control can be supported by sensor on-line monitoring, and data validation through soft-computing process. On-line recalibration can often avoid manual calibration or drifting component replacement. DSP requires prompt response to the modified conditions. Artificial Neural Network (ANN) and Fuzzy logic ensure: prompt response, link with field measurement and physical system behaviour, data incoming interpretation, and detection of discrepancy for mis-calibration or sensor faults. ANN (Artificial Neural Network) is a system based on the operation of biological neural networks. Although computing is day by day advancing, there are certain tasks that a program made for a common microprocessor is unable to perform. A software implementation of an ANN can be made with Pros and Cons. Pros: A neural network can perform tasks that a linear program can not; When an element of the neural network fails, it can continue without any problem by their parallel nature; A neural network learns and does not need to be reprogrammed; It can be implemented in any application; It can be implemented without any problem. Cons: The architecture of a neural network is different from the architecture of microprocessors therefore needs to be emulated; it requires high processing time for large neural networks; and the neural network needs training to operate. Three possibilities of training exist: Supervised learning: the network is trained providing input and matching output patterns; Unsupervised learning: input patterns are not a priori classified and the system must develop its own representation of the input stimuli; Reinforcement Learning: intermediate form of the above two types of learning, the learning machine does some action on the environment and gets a feedback response from the environment. Two TRIGAN ANN applications are considered: control rod position and fuel temperature. The outcome obtained in this

  8. Monitoring Countries in a Changing World: A New Look at DIF in International Surveys.

    Science.gov (United States)

    Zwitser, Robert J; Glaser, S Sjoerd F; Maris, Gunter

    2017-03-01

    This paper discusses the issue of differential item functioning (DIF) in international surveys. DIF is likely to occur in international surveys. What is needed is a statistical approach that takes DIF into account, while at the same time allowing for meaningful comparisons between countries. Some existing approaches are discussed and an alternative is provided. The core of this alternative approach is to define the construct as a large set of items, and to report in terms of summary statistics. Since the data are incomplete, measurement models are used to complete the incomplete data. For that purpose, different models can be used across countries. The method is illustrated with PISA's reading literacy data. The results indicate that this approach fits the data better than the current PISA methodology; however, the league tables are nearly identical. The implications for monitoring changes over time are discussed.

  9. Internal dose assessment for environmental monitoring in nuclear power plant accidents

    Directory of Open Access Journals (Sweden)

    Mianji Fereidoun A.

    2013-01-01

    Full Text Available A method for exploiting human's internal contamination data for radioactive release estimation in nuclear power plant accidents is proposed. Nevertheless, such data is often very rough and uncertain; it is accessible even in toughest situations when most of the active and passive monitors are damaged by the accident. These data can be used in combination with other collectable data for estimating the event scale in severe nuclear power plan accidents. The rationale behind the method is that nuclear power plant accidents are often associated with internal contamination of radiation workers involved in the early stages of emergency response activities mainly due to the release of 131I in atmosphere. The proposed inverse analytical approach uses the 131I intake of contaminated workers, their working conditions, chronology of events, and applied personal safety measures during the first hours or days of the emergency response activities to estimate the magnitude of 131I concentration in the air.

  10. Between forwarding and mentoring: a qualitative study of recommending medical doctors for international postdoctoral research positions

    Directory of Open Access Journals (Sweden)

    Marušić Matko

    2011-06-01

    Full Text Available Abstract Background Young scientists rarely have extensive international connections that could facilitate their mobility. They often rely on their doctoral supervisors and other senior academics, who use their networks to generate opportunities for young scientists to gain international experience and provide the initial trigger for an outward move. Methods To explore the process of informal recommending of young physicians from a small country for postdoctoral research positions in foreign countries, we conducted in-depth interviews with eight senior academics who acted as recommenders and eight physicians who, based on the recommendations of senior academics, spent at least a year working in a laboratory abroad. Interviews were transcribed and analyzed by using the framework approach. Results The findings showed that recommending can take four distinct forms: 1 forwarding information, 2 passive recommending, 3 active recommending, and 4 mentor recommending. These forms differ in their level of commitment and mutual trust among actors, and possible control over the success of the process. Two groups of recommendees - 'naive' and 'experienced' - can be distinguished based on their previous scientific experience and research collaboration with the recommender. Crucial for the success of the process is an adequate preparation of recommendees' stay abroad, as well as their return and reintegration. The benefits of recommending extend beyond the individual participants to the scientific community and broader society of the sending country. Conclusions With a sufficient level of commitment by the actors, informal recommending can be a part of or grow into an all-encompassing developmental relationship equal to mentoring. The importance of senior academics' informal contacts and recommendations in promoting junior scientists' mobility should be acknowledged and encouraged by the research institutions and universities, particularly in developing

  11. Production structure and international competition position of the German environmental protection economy; Produktionsstruktur und internationale Wettbewerbsposition der deutschen Umweltschutzwirtschaft

    Energy Technology Data Exchange (ETDEWEB)

    Legler, Harald; Schasse, Ulrich [Niedersaechsisches Institut fuer Wirtschaftsforschung e.V., Hannover (Germany)

    2009-06-15

    There exists a connection between the economic structural orientation and international competitiveness on the one hand as well as the environmental political requirements on the other hand. The environmental protection economy fits quite well the profile that Germany is demanded in the international change. Under this aspect, the authors of the contribution under consideration report on the production structure and on the international competition position of the German environmental protection economy. The authors report on (a) the production structure and production dynamics of the environmental protection industry; (b) German environmental protection economy in the international comparison; (c) Goods, building works and services for environmental protection in Germany.

  12. Operational Experience with Beam Alignment and Monitoring Using Non-Destructive Beam Position Monitors in the Cyclotron Beamlines at iThemba LABS

    CERN Document Server

    Conradie, J L; Delsink, J L G; Fourie, D T; Kormany, Z; Mansfield, P T; Rohwer, P F; Sakildien, M

    2005-01-01

    At iThemba LABS proton beams, accelerated in a K=200 separated-sector cyclotron with a K=8 solid-pole injector cyclotron, are utilized for the production of radioisotopes and particle radiotherapy. Beams of heavy ions and polarized protons, pre-accelerated in a second injector cyclotron, are available for nuclear physics research. Beam position monitors have been developed for non-destructive alignment and continuous display of the beam position in the beam lines for the more intense beams used for therapy and the production of radioisotopes in cooperation* with Forschungszentrum Jülich. The monitors consist of four-section strip lines. Narrow-band super-heterodyne RF electronic equipment with automatic frequency and gain control measures the signals at the selected harmonic. A control module sequentially processes the signals and delivers calculated horizontal and vertical beam position data via a serial network to the computer control system. Eleven monitors have been installed in the transfer beam line be...

  13. Expansion of Microbial Monitoring Capabilities on the International Space Station (ISS)

    Science.gov (United States)

    Khodadad, Christina L.; Oubre, Cherie; Castro, Victoria; Flint, Stephanie; Melendez, Orlando; Ott, C. Mark; Roman, Monsi

    2017-01-01

    Microbial monitoring is one of the tools that the National Aeronautics and Space Administration (NASA) uses on the International Space Station (ISS) to help maintain crew health and safety. In combination with regular housekeeping and disinfection when needed, microbial monitoring provides important information to the crew about the quality of the environment. Rotation of astronauts, equipment, and cargo on the ISS can affect the microbial load in the air, surfaces, and water. The current ISS microbial monitoring methods are focused on culture-based enumeration during flight and require a significant amount of crew time as well as long incubation periods of up to 5 days there by proliferating potential pathogens. In addition, the samples require return to Earth for complete identification of the microorganisms cultivated. Although the current approach assess the quality of the ISS environment, molecular technology offers faster turn-around of information particularly beneficial in an off-nominal situation. In 2011, subject matter experts from industry and academia recommended implementation of molecular-based technologies such as quantitative real-time polymerase chain reaction (qPCR) for evaluation to replace current, culture-based technologies. The RAZOR EX (BioFire Defense, Inc, Salt Lake City, UT) a ruggedized, compact, COTS (commercial off the shelf) qPCR instrument was tested, evaluated and selected in the 2 X 2015 JSC rapid flight hardware demonstration initiative as part of the Water Monitoring Suite. RAZOR EX was launched to ISS on SpaceX-9 in July 2016 to evaluate the precision and accuracy of the hardware by testing various concentrations of DNA in microgravity compared to ground controls. Flight testing was completed between September 2016 and March 2017. Data presented will detail the hardware performance of flight testing results compared to ground controls. Future goals include additional operational ground-based testing and assay development to

  14. International Society of Sports Nutrition Position Stand: beta-hydroxy-beta-methylbutyrate (HMB

    Directory of Open Access Journals (Sweden)

    Wilson Jacob M

    2013-02-01

    Full Text Available Abstract Position Statement: The International Society of Sports Nutrition (ISSN bases the following position stand on a critical analysis of the literature on the use of beta-hydroxy-beta-methylbutyrate (HMB as a nutritional supplement. The ISSN has concluded the following. 1. HMB can be used to enhance recovery by attenuating exercise induced skeletal muscle damage in trained and untrained populations. 2. If consuming HMB, an athlete will benefit from consuming the supplement in close proximity to their workout. 3. HMB appears to be most effective when consumed for 2 weeks prior to an exercise bout. 4. Thirty-eight mg·kg·BM-1 daily of HMB has been demonstrated to enhance skeletal muscle hypertrophy, strength, and power in untrained and trained populations when the appropriate exercise prescription is utilized. 5. Currently, two forms of HMB have been used: Calcium HMB (HMB-Ca and a free acid form of HMB (HMB-FA. HMB-FA may increase plasma absorption and retention of HMB to a greater extent than HMB-CA. However, research with HMB-FA is in its infancy, and there is not enough research to support whether one form is superior. 6. HMB has been demonstrated to increase LBM and functionality in elderly, sedentary populations. 7. HMB ingestion in conjunction with a structured exercise program may result in greater declines in fat mass (FM. 8. HMB’s mechanisms of action include an inhibition and increase of proteolysis and protein synthesis, respectively. 9. Chronic consumption of HMB is safe in both young and old populations.

  15. International Society of Sports Nutrition Position Stand: beta-hydroxy-beta-methylbutyrate (HMB)

    Science.gov (United States)

    2013-01-01

    Position Statement: The International Society of Sports Nutrition (ISSN) bases the following position stand on a critical analysis of the literature on the use of beta-hydroxy-beta-methylbutyrate (HMB) as a nutritional supplement. The ISSN has concluded the following. 1. HMB can be used to enhance recovery by attenuating exercise induced skeletal muscle damage in trained and untrained populations. 2. If consuming HMB, an athlete will benefit from consuming the supplement in close proximity to their workout. 3. HMB appears to be most effective when consumed for 2 weeks prior to an exercise bout. 4. Thirty-eight mg·kg·BM-1 daily of HMB has been demonstrated to enhance skeletal muscle hypertrophy, strength, and power in untrained and trained populations when the appropriate exercise prescription is utilized. 5. Currently, two forms of HMB have been used: Calcium HMB (HMB-Ca) and a free acid form of HMB (HMB-FA). HMB-FA may increase plasma absorption and retention of HMB to a greater extent than HMB-CA. However, research with HMB-FA is in its infancy, and there is not enough research to support whether one form is superior. 6. HMB has been demonstrated to increase LBM and functionality in elderly, sedentary populations. 7. HMB ingestion in conjunction with a structured exercise program may result in greater declines in fat mass (FM). 8. HMB’s mechanisms of action include an inhibition and increase of proteolysis and protein synthesis, respectively. 9. Chronic consumption of HMB is safe in both young and old populations. PMID:23374455

  16. External Ventricular Catheters: Is It Appropriate to Use an Open/Monitor Position to Adequately Trend Intracranial Pressure in a Neuroscience Critical Care Environment?

    Science.gov (United States)

    Sunderland, Nicole E; Villanueva, Nancy E; Pazuchanics, Susan J

    2016-10-01

    Intracranial pressure (ICP) monitoring can be an important assessment tool in critically and acutely ill patients. An external ventricular drain offers a comprehensive way to monitor ICP and drain cerebrospinal fluid. The Monro-Kellie hypothesis, Pascal's principle, and fluid dynamics were used to formulate an assumption that an open/monitor position on the stopcock is an adequate trending measure for ICP monitoring while concurrently draining cerebrospinal fluid. Data were collected from 50 patients and totaled 1053 separate number sets. The open/monitor position was compared with the clamped position every hour. An order for "open to drain" was needed for appropriate measurement and nursing care. Results showed the absolute average differences between open/monitor and clamped positions at 1.6268 mm Hg. This finding suggests that it is appropriate to use an open/monitor position via an external ventricular drain for adequate trending of patients' ICP.

  17. Position of Serbia on the international market of milk, dairy products, eggs and wool

    Directory of Open Access Journals (Sweden)

    Đorović Milutin

    2011-01-01

    Full Text Available This paper presents a comparative analysis of the major indicators of both world and domestic markets of milk, dairy products, eggs and wool. Namely, for the past 20 years, for the observed subperiods, the method of comparative analysis was used to study quantitative and structural differences in the production and trade of analyzed product groups, at both the world and at the level of continents and some countries. The leading manufacturers and flows of international trade and the leading exporters and importers of milk, dairy products, eggs and wool were defined, with special emphasis on importance of Serbia, i.e. its position in the global market for these products. Pursuant to the above, and importance of analyzed product groups for the domestic market, i.e. agroindustry and the economy as a whole, this paper specially studies balances, structure, dynamics and regional orientation of foreign trade in milk, dairy products, eggs and wool. In addition, the paper points to the needs, capabilities, measures and directions of further development of domestic production and export of products analyzed.

  18. Data Analysis of Seismic Sequence in Central Italy in 2016 using CTBTO- International Monitoring System

    Science.gov (United States)

    Mumladze, Tea; Wang, Haijun; Graham, Gerhard

    2017-04-01

    The seismic network that forms the International Monitoring System (IMS) of the Comprehensive Nuclear-test-ban Treaty Organization (CTBTO) will ultimately consist of 170 seismic stations (50 primary and 120 auxiliary) in 76 countries around the world. The Network is still under the development, but currently more than 80% of the network is in operation. The objective of seismic monitoring is to detect and locate underground nuclear explosions. However, the data from the IMS also can be widely used for scientific and civil purposes. In this study we present the results of data analysis of the seismic sequence in 2016 in Central Italy. Several hundred earthquakes were recorded for this sequence by the seismic stations of the IMS. All events were accurately located the analysts of the International Data Centre (IDC) of the CTBTO. In this study we will present the epicentral and magnitude distribution, station recordings and teleseismic phases as obtained from the Reviewed Event Bulletin (REB). We will also present a comparison of the database of the IDC with the databases of the European-Mediterranean Seismological Centre (EMSC) and U.S. Geological Survey (USGS). Present work shows that IMS data can be used for earthquake sequence analyses and can play an important role in seismological research.

  19. Software requirements elicitation to support internal monitoring of quality assurance system for higher education in Indonesia

    Science.gov (United States)

    Amalia, A.; Gunawan, D.; Hardi, S. M.; Rachmawati, D.

    2018-02-01

    The Internal Quality Assurance System (in Indonesian: SPMI (Sistem Penjaminan Mutu Internal) is a systemic activity of quality assurance of higher education in Indonesia. SPMI should be done by all higher education or universities in Indonesia based on the Regulation of the Minister of Research, Technology and Higher Education of the Republic of Indonesia Number 62 of 2016. Implementation of SPMI must refer to the principle of SPMI that is independent, standardize, accurate, well planned and sustainable, documented and systematic. To assist the SPMI cycle properly, universities need a supporting software to monitor all the activities of SPMI. But in reality, many universities are not optimal in building this SPMI monitoring system. One of the obstacles is the determination of system requirements in support of SPMI principles is difficult to achieve. In this paper, we observe the initial phase of the engineering requirements elicitation. Unlike other methods that collect system requirements from users and stakeholders, we find the system requirements of the SPMI principles from SPMI guideline book. The result of this paper can be used as a choice in determining SPMI software requirements. This paper can also be used by developers and users to understand the scenario of SPMI so that could overcome the problems of understanding between this two parties.

  20. Proceedings of the International Workshop on Sustainable ForestManagement: Monitoring and Verification of Greenhouse Gases

    Energy Technology Data Exchange (ETDEWEB)

    Sathaye (Ed.), Jayant; Makundi (Ed.), Willy; Goldberg (Ed.),Beth; Andrasko (Ed.), Ken; Sanchez (Ed.), Arturo

    1997-07-01

    The International Workshop on Sustainable Forest Management: Monitoring and Verification of Greenhouse Gases was held in San Jose, Costa Rica, July 29-31, 1996. The main objectives of the workshop were to: (1) assemble key practitioners of forestry greenhouse gas (GHG) or carbon offset projects, remote sensing of land cover change, guidelines development, and the forest products certification movement, to offer presentations and small group discussions on findings relevant to the crucial need for the development of guidelines for monitoring and verifying offset projects, and (2) disseminate the findings to interested carbon offset project developers and forestry and climate change policy makers, who need guidance and consistency of methods to reduce project transaction costs and increase probable reliability of carbon benefits, at appropriate venues. The workshop brought together about 45 participants from developed, developing, and transition countries. The participants included researchers, government officials, project developers, and staff from regional and international agencies. Each shared his or her perspectives based on experience in the development and use of methods for monitoring and verifying carbon flows from forest areas and projects. A shared sense among the participants was that methods for monitoring forestry projects are well established, and the techniques are known and used extensively, particularly in production forestry. Introducing climate change with its long-term perspective is often in conflict with the shorter-term perspective of most forestry projects and standard accounting principles. The resolution of these conflicts may require national and international agreements among the affected parties. The establishment of guidelines and protocols for better methods that are sensitive to regional issues will be an important first step to increase the credibility of forestry projects as viable mitigation options. The workshop deliberations led

  1. The position of the Bureau of International Recycling on unwanted radioactivity and scrap

    International Nuclear Information System (INIS)

    Neenan, P.; Bartley, R.

    1999-01-01

    The Bureau of International Recycling (BIR) speaks as the unified voice of the international recycling industry on a world level, promoting free-trade in non-hazardous recyclables and the increased usage of recycled goods. In October 1998, BIR presented its 'Guide to Radioactivity' to its members in order to explain the basics of radioactivity, to help determine what actions material recyclers should take and to provide an initial contact guide for summoning expert help. The Guide was promulgated together with a survey questionnaire; initial results of this survey have been collated. BIR members do not trade in radioactive materials and do not wish to receive hazardous radioactive contaminated materials. Furthermore it is very uncommon to find this unwelcome and unwanted material. The burden of handling contaminated materials should not rest on the recycling industry alone, however, as the hazards associated with processing contaminated materials are potentially extreme, recyclers have a role to help safeguard both their workforce and subsequent customers. Some BIR members have invested in in-plant detection equipment of various types from a variety of suppliers to detect contamination from 'lost' sources or from naturally occurring radioactive materials (NORM). Strict State control on sources in use would be very welcome to limit these ' losses'. Not all BIR members are in a position to provide or operate detection equipment; therefore, BIR would welcome States providing detection and control at sea ports and at border checkpoints on railways and roads. Some states have proposed permitting requirements for the handling of radioactive contaminated materials and have tried, inappropriately, to impose on the mainstream recycling industry, permits designed for the specialist decontamination or decommissioning industry. Current discussions on applying the transport of dangerous goods regulations would lead to unnecessary and impracticable additional restraints to

  2. The application of artificial vision to the monitoring of immobility and the position of patients in external therapy

    International Nuclear Information System (INIS)

    Piombo, Ch.; Petit, J.L.; Costa, A.; Lagrange, J.L.

    1995-01-01

    The result of a radiation treatment is linked to the accuracy of the patient's position, his immobility during the treatment time and the repeatability of the patient's position during the various sessions. The psychological aspects which prevent the use of immobilisation constraints have lead radiotherapists to examine the use of artificial vision to perform qualimetry based on immobility and repositioning. As concerns immobility monitoring: the image of the scene, sampled according to a reference grid to reduce the size of the information, is compared in real time to a file which constitutes the reference to the initial position. This enables the detection of non stationary points which are indicative of local movements. To eliminate the artefacts, a check is performed over the eight neighbouring points of each sample, and only the points which represent a real movement are considered. As the quality of detection is linked to the computation time, observation windows are determined by the physician during the first session which enable detection to be limited to observation of the defined fields only. As concerns position monitoring: the positional differences between the position corresponding to the first session taken as a reference, and the position under observation to be monitored, result from the measurements obtained by the co-location of a vector modelling the current image with the vector modelling in the same manner the reference image limited by a window over the part of the image visualising the target volume. A successive presentation is made of the environmental specifications, the heuristics involved in the processing of images providing the elimination of acquisition chain interference, variations in the brightness of treatment rooms and natural physiological movements such as the blinking of cyclids, and the experimental results obtained on site

  3. The JPL Electronic Nose: Monitoring Air in the US Lab on the International Space Station

    Science.gov (United States)

    Ryan, M. A.; Manatt, K. S.; Gluck, S.; Shevade, A. V.; Kisor, A. K.; Zhou, H.; Lara, L. M.; Homer, M. L.

    2010-01-01

    An electronic nose with a sensor array of 32 conductometric sensors has been developed at the Jet Propulsion Laboratory (JPL) to monitor breathing air in spacecraft habitat. The Third Generation ENose is designed to operate in the environment of the US Lab on the International Space Station (ISS). It detects a selected group of analytes at target concentrations in the ppm regime at an environmental temperature range of 18 - 30 oC, relative humidity from 25 - 75% and pressure from 530 to 760 torr. The monitoring targets are anomalous events such as leaks and spills of solvents, coolants or other fluids. The JPL ENose operated as a technology demonstration for seven months in the U.S. Laboratory Destiny during 2008-2009. Analysis of ENose monitoring data shows that there was regular, periodic rise and fall of humidity and occasional releases of Freon 218 (perfluoropropane), formaldehyde, methanol and ethanol. There were also several events of unknown origin, half of them from the same source. Each event lasted from 20 to 100 minutes, consistent with the air replacement time in the US Lab.

  4. Monitoring the Microgravity Environment Quality On-Board the International Space Station Using Soft Computing Techniques

    Science.gov (United States)

    Jules, Kenol; Lin, Paul P.

    2001-01-01

    This paper presents an artificial intelligence monitoring system developed by the NASA Glenn Principal Investigator Microgravity Services project to help the principal investigator teams identify the primary vibratory disturbance sources that are active, at any moment in time, on-board the International Space Station, which might impact the microgravity environment their experiments are exposed to. From the Principal Investigator Microgravity Services' web site, the principal investigator teams can monitor via a graphical display, in near real time, which event(s) is/are on, such as crew activities, pumps, fans, centrifuges, compressor, crew exercise, platform structural modes, etc., and decide whether or not to run their experiments based on the acceleration environment associated with a specific event. This monitoring system is focused primarily on detecting the vibratory disturbance sources, but could be used as well to detect some of the transient disturbance sources, depending on the events duration. The system has built-in capability to detect both known and unknown vibratory disturbance sources. Several soft computing techniques such as Kohonen's Self-Organizing Feature Map, Learning Vector Quantization, Back-Propagation Neural Networks, and Fuzzy Logic were used to design the system.

  5. Management of bank risks in the system of internal financial monitoring

    Directory of Open Access Journals (Sweden)

    O.V. Lysenok

    2015-09-01

    Full Text Available Risk is an integral part of banking activities. That is why there are many researches on definition, measurement and monitoring of banking risks. Nowadays it is important to improve the risk management process of legalization (laundering of proceeds from crime or terrorist financing, especially in the present conditions of socio-economic development. This will improve the quality of financial monitoring in the country as a whole and will reduce the risk of attracting banks to laundering money from crime. The article reviews and examines modern management techniques and risk assessment of laundering proceeds from crime. The authors make suggestions to strengthen the tracking and detection of illegal schemes and appropriate approaches to «launder» criminal money. They also offer an appropriate model to manage the risks which accompany the process of laundering the proceeds from crime. According to the study carried out the authors provide their conclusions and recommendations to improve risk management in the system of internal financial monitoring of banks.

  6. Program of individual monitoring of the internal contamination and their implementation in the Republic the Cuba

    International Nuclear Information System (INIS)

    Lopez Bejerano, Gladys M.; Capote Ferrera, Eduardo; Fernandez Gomez, Isis M.; Acosta Rodriguez, Nancy; Carrazana Gonzalez, Jorge A.; Cruz Suarez, Rodolfo

    2008-01-01

    Full text: In different Cuban institutions linked fundamentally to the medical practice of nuclear medicine and the investigations, it is worked with sources open of ionizing radiations, that which makes indispensable the existence of a system of radiological surveillance that includes the control radiological individual of the received doses as a result of the occupational, such exhibition that is guaranteed that the exhibition of the Hard-working Exposed Occupationally, stay inside the recommended limits, in the International Basic Norms of Protection against the Ionizing radiations and safe-deposit of the Sources of Radiation (NBIS) and in turn adopted in the Norma Cuban. From the year 1986 in the Center of Protection and Hygiene of the Radiations is carried out in way centralized this control; but with the inconvenience of not being able to carry out the same one to workers from the domestic interior when not being feasible the transfer of these toward its headquarters, reason why the doses were ignored received in an important number of these. In and of itself the Laboratory of Internal Contamination of this institution in these years has developed managed works to define firstly, for each institution, the program of monitoring of the internal contamination of its workers using for it the methodology recommended by the OIEA where the potential doses are evaluated that for incorporation these they receive and whose results suggested the introduction of a program of individual monitoring as behavior to continue in most of the institutions. In correspondence with it was designed and established a program that included the study of feasibility of the existent equipment in the institutions to carry out the monitoring of the internal contamination using technical of measuring in vivo and in vitro, as it corresponds, their calibration, the establishment of procedures that respond to the requirements of a System of Quality for the Norma ISO/IEC 17025 and

  7. Roadmap for the international collaborative epidemiologic monitoring of safety and effectiveness of new high priority vaccines.

    Science.gov (United States)

    Izurieta, Hector S; Zuber, Patrick; Bonhoeffer, Jan; Chen, Robert T; Sankohg, Osman; Laserson, Kayla F; Sturkenboom, Miriam; Loucq, Christian; Weibel, Daniel; Dodd, Caitlin; Black, Steve

    2013-08-02

    With the advent of new vaccines targeted to highly endemic diseases in low- and middle-income countries (LMIC) and with the expansion of vaccine manufacturing globally, there is an urgent need to establish an infrastructure to evaluate the benefit-risk profiles of vaccines in LMIC. Fortunately the usual decade(s)-long time gap between introduction of new vaccines in high and low income countries is being significantly reduced or eliminated due to initiatives such as the Global Alliance for Vaccines and Immunizations (GAVI) and the Decade of Vaccines for the implementation of the Global Vaccine Action Plan. While hoping for more rapid disease control, this time shift may potentially add risk, unless appropriate capacity for reliable and timely evaluation of vaccine benefit-risk profiles in some LMIC's are developed with external assistance from regional or global level. An ideal vaccine safety and effectiveness monitoring system should be flexible and sustainable, able to quickly detect possible vaccine-associated events, distinguish them from programmatic errors, reliably and quickly evaluate the suspected event and its association with vaccination and, if associated, determine the benefit-risk of vaccines to inform appropriate action. Based upon the demonstrated feasibility of active surveillance in LMIC as shown by the Burkina Faso assessment of meningococcal A conjugate vaccine or that of rotavirus vaccine in Mexico and Brazil, and upon the proof of concept international GBS study, we suggest a sustainable, flexible, affordable and timely international collaborative vaccine safety monitoring approach for vaccines being newly introduced. While this paper discusses only the vaccine component, the same system could also be eventually used for monitoring drug effectiveness (including the use of substandard drugs) and drug safety. Published by Elsevier Ltd.

  8. The difference in the position of Mexico, Japan and China as recipients of international tourism and their position in Competitiveness Index Travel and Tourism

    Directory of Open Access Journals (Sweden)

    Irma Magaña Carrillo

    2012-06-01

    Full Text Available Mexico, as a tourist destination that is recipient of tourists, ranks among the top ten in terms of international arrivals. Nevertheless, in terms of competitiveness, according to the index of Travel and Tourism Competitiveness, its ranking is very low. This research project looks to understand and explain the differences in tourist competitiveness between Mexico and other countries within the Asia-Pacific Basin. This article is preoccupied with the question posed by Mexico’s evident contradicting position as that of being on the one hand, leader in terms of international arrivals, and on the other, having a low competitive performance, according to the index of international tourist competitiveness. Comparing Mexico to Japan and China, helps to understand what aspects, among those considered in the index pillars, should be contemplated in order to strengthen Mexico’s levels of competitiveness, as suggested in the Tourist Sectorial Plan 2007-2012.

  9. European society of hypertension position paper on ambulatory blood pressure monitoring

    NARCIS (Netherlands)

    O'Brien, Eoin; Parati, Gianfranco; Stergiou, George; Asmar, Roland; Beilin, Laurie; Bilo, Grzegorz; Clement, Denis; de la Sierra, Alejandro; de Leeuw, Peter; Dolan, Eamon; Fagard, Robert; Graves, John; Head, Geoffrey A.; Imai, Yutaka; Kario, Kazuomi; Lurbe, Empar; Mallion, Jean-Michel; Mancia, Giuseppe; Mengden, Thomas; Myers, Martin; Ogedegbe, Gbenga; Ohkubo, Takayoshi; Omboni, Stefano; Palatini, Paolo; Redon, Josep; Ruilope, Luis M.; Shennan, Andrew; Staessen, Jan A.; vanMontfrans, Gert; Verdecchia, Paolo; Waeber, Bernard; Wang, Jiguang; Zanchetti, Alberto; Zhang, Yuqing

    2013-01-01

    Ambulatory blood pressure monitoring (ABPM) is being used increasingly in both clinical practice and hypertension research. Although there are many guidelines that emphasize the indications for ABPM, there is no comprehensive guideline dealing with all aspects of the technique. It was agreed at a

  10. International society of sports nutrition position stand: diets and body composition.

    Science.gov (United States)

    Aragon, Alan A; Schoenfeld, Brad J; Wildman, Robert; Kleiner, Susan; VanDusseldorp, Trisha; Taylor, Lem; Earnest, Conrad P; Arciero, Paul J; Wilborn, Colin; Kalman, Douglas S; Stout, Jeffrey R; Willoughby, Darryn S; Campbell, Bill; Arent, Shawn M; Bannock, Laurent; Smith-Ryan, Abbie E; Antonio, Jose

    2017-01-01

    Position Statement: The International Society of Sports Nutrition (ISSN) bases the following position stand on a critical analysis of the literature regarding the effects of diet types (macronutrient composition; eating styles) and their influence on body composition. The ISSN has concluded the following. 1) There is a multitude of diet types and eating styles, whereby numerous subtypes fall under each major dietary archetype. 2) All body composition assessment methods have strengths and limitations. 3) Diets primarily focused on fat loss are driven by a sustained caloric deficit. The higher the baseline body fat level, the more aggressively the caloric deficit may be imposed. Slower rates of weight loss can better preserve lean mass (LM) in leaner subjects. 4) Diets focused primarily on accruing LM are driven by a sustained caloric surplus to facilitate anabolic processes and support increasing resistance-training demands. The composition and magnitude of the surplus, as well as training status of the subjects can influence the nature of the gains. 5) A wide range of dietary approaches (low-fat to low-carbohydrate/ketogenic, and all points between) can be similarly effective for improving body composition. 6) Increasing dietary protein to levels significantly beyond current recommendations for athletic populations may result in improved body composition. Higher protein intakes (2.3-3.1 g/kg FFM) may be required to maximize muscle retention in lean, resistance-trained subjects under hypocaloric conditions. Emerging research on very high protein intakes (>3 g/kg) has demonstrated that the known thermic, satiating, and LM-preserving effects of dietary protein might be amplified in resistance-training subjects. 7) The collective body of intermittent caloric restriction research demonstrates no significant advantage over daily caloric restriction for improving body composition. 8) The long-term success of a diet depends upon compliance and suppression or

  11. Automated system of monitoring and positioning of functional units of mining technological machines for coal-mining enterprises

    Directory of Open Access Journals (Sweden)

    Meshcheryakov Yaroslav

    2018-01-01

    Full Text Available This article is show to the development of an automated monitoring and positioning system for functional nodes of mining technological machines. It describes the structure, element base, algorithms for identifying the operating states of a walking excavator; various types of errors in the functioning of microelectromechanical gyroscopes and accelerometers, as well as methods for their correction based on the Madgwick fusion filter. The results of industrial tests of an automated monitoring and positioning system for functional units on one of the opencast coal mines of Kuzbass are presented. This work is addressed to specialists working in the fields of the development of embedded systems and control systems, radio electronics, mechatronics, and robotics.

  12. Measurement of resonance modes causative of beam position monitor signal noise in vacuum chamber of storage ring

    International Nuclear Information System (INIS)

    Joo, Youngdo; Hwang, Ilmoon; Park, Sungju; Kim, Changbum

    2011-01-01

    It is known that the position reading obtained from the beam position monitor (BPM) mounted at the storage ring can be corrupted by the resonance mode. We carried out a three dimensional finite-difference time-domain (FDTD) simulation of vacuum chambers of the storage ring of the Pohang Light Source (PLS) without simplified modeling to measure the frequencies of resonance modes excited in the vacuum chamber. The frequencies of resonance modes obtained by the eigenmode simulation are well matched with the peak frequencies of RF transmission scattering matrix (S 21 ) graph of sector vacuum chamber measured using a network analyzer. It is found that a transverse electric (TE) resonance mode exists in the operation frequency band of BPM and the vertically oriented electric field of TE resonance mode is linked to the BPM position reading noise. Based on this study, we can easily design a vacuum chamber free from the BPM position reading noise caused by the TE resonance mode.

  13. Reconstruction of lattice parameters and beam momentum distribution from turn-by-turn beam position monitor readings in circular accelerators

    Directory of Open Access Journals (Sweden)

    C. S. Edmonds

    2014-05-01

    Full Text Available In high chromaticity circular accelerators, rapid decoherence of the betatron motion of a particle beam can make the measurement of lattice and bunch values, such as Courant-Snyder parameters and betatron amplitude, difficult. A method for reconstructing the momentum distribution of a beam from beam position measurements is presented. Further analysis of the same beam position monitor data allows estimates to be made of the Courant-Snyder parameters and the amplitude of coherent betatron oscillation of the beam. The methods are tested through application to data taken on the linear nonscaling fixed field alternating gradient accelerator, EMMA.

  14. Individual monitoring of internal exposure of 131I of workers from the nuclear medicine service FUESMEN, Argentina

    International Nuclear Information System (INIS)

    Arenas, G.; Acosta, N.; Venier, V.; Bedoya Toboo, C.

    2013-01-01

    It is presented the FUESMEN experience in routine monitoring of thyroid internal doses due to inhalation of 131 I in workers of the Nuclear Medicine Service in normal operation or accidental exposure. It is used a surface contamination monitor, type Geiger Mueller, calibrated with a acrylic phantom based on specifications of the simulator of thyroid of ICRU 48 with 131 I reference activity. Through the obtained measurements is achieved to validate the use of Portable Monitor to carry out preliminary exploration on the monitoring scenarios of incidental situations

  15. The image of Russia in 2010—2011 international indices: positioning crisis

    Directory of Open Access Journals (Sweden)

    Berendeev Mikhail

    2011-09-01

    Full Text Available This paper considers the political and economic shortcomings of the image of Russia and its perception by the international community in 2010—2011. International indices are a comprehensive information source in terms of the economic and political image of a country and, to a great extent, a decisive factor in the global trends relevant to different countries and their development potentials. The author also compares the international images of Russia and the Baltic Sea region countries.

  16. A Fast Non Intercepting Linac Electron Beam Position and Current Monitor

    DEFF Research Database (Denmark)

    Hansen, Jørgen-Walther; Wille, Mads

    1982-01-01

    are achieved by subtracting one signal from the other and adding the two signals, respectively. For displacements below 2 mm from the center axis an average sensitivity of 0.5 mV/mm·mA is measured, whereas displacements more than 2 mm yields 1.3 mV / mm·mA. A sensitivity of 0.2 mV / mA in current monitoring...

  17. Biological Monitoring of HER-2 Positive Patients Using Serum HER-2 and Circulating Tumor Cells

    National Research Council Canada - National Science Library

    Fournier, Marcia

    2002-01-01

    ...: Blood samples were collected from 55 women with HER-2 positive (lHC+++ and/or FlSH+) metastatic breast cancer and 30 healthy female volunteers Blood samples were collected at baseline, during With the first cycle...

  18. INFORMAS (International Network for Food and Obesity/non-communicable diseases Research, Monitoring and Action Support): overview and key principles.

    Science.gov (United States)

    Swinburn, B; Sacks, G; Vandevijvere, S; Kumanyika, S; Lobstein, T; Neal, B; Barquera, S; Friel, S; Hawkes, C; Kelly, B; L'abbé, M; Lee, A; Ma, J; Macmullan, J; Mohan, S; Monteiro, C; Rayner, M; Sanders, D; Snowdon, W; Walker, C

    2013-10-01

    Non-communicable diseases (NCDs) dominate disease burdens globally and poor nutrition increasingly contributes to this global burden. Comprehensive monitoring of food environments, and evaluation of the impact of public and private sector policies on food environments is needed to strengthen accountability systems to reduce NCDs. The International Network for Food and Obesity/NCDs Research, Monitoring and Action Support (INFORMAS) is a global network of public-interest organizations and researchers that aims to monitor, benchmark and support public and private sector actions to create healthy food environments and reduce obesity, NCDs and their related inequalities. The INFORMAS framework includes two 'process' modules, that monitor the policies and actions of the public and private sectors, seven 'impact' modules that monitor the key characteristics of food environments and three 'outcome' modules that monitor dietary quality, risk factors and NCD morbidity and mortality. Monitoring frameworks and indicators have been developed for 10 modules to provide consistency, but allowing for stepwise approaches ('minimal', 'expanded', 'optimal') to data collection and analysis. INFORMAS data will enable benchmarking of food environments between countries, and monitoring of progress over time within countries. Through monitoring and benchmarking, INFORMAS will strengthen the accountability systems needed to help reduce the burden of obesity, NCDs and their related inequalities. © 2013 The Authors. Obesity Reviews published by John Wiley & Sons Ltd on behalf of the International Association for the Study of Obesity.

  19. The effect of textile-based inductive coil sensor positions for heart rate monitoring.

    Science.gov (United States)

    Koo, Hye Ran; Lee, Young-Jae; Gi, Sunok; Khang, Seonah; Lee, Joo Hyeon; Lee, Jae-Ho; Lim, Min-Gyu; Park, Hee-Jung; Lee, Jeong-Whan

    2014-02-01

    In the research related to heart rate measurement, few studies have been done using magnetic-induced conductivity sensing methods to measure the heart rate. The aim of this study was to analyze the effect of the position of a textile-based inductive coil sensor on the measurement of the heart rate. In order to assess the capability of the textile-based inductive coil sensor and the repeatability of measured cardiac muscle contractions, we proposed a new quality index based on the morphology of measured signals using a textile-based inductive coil sensor. We initially explored eight potential positions of the inductive sensor in a pilot experiment, followed by three sensor positions in the main experiment. A simultaneously measured electrocardiography (ECG) signal (Lead II) which was used as a reference signal for a comparison of the R-peak location with signals obtained from selected positions of the textile-based inductive coil sensor. The result of the main experiment indicated that the total quality index obtained from the sensor position 'P3', which was located 3 cm away from the left side from the center front line on the chest circumference line, was the highest (QI value = 1.30) among the three positions across all the subjects. This finding led us to conclude that (1) the position of the textile-based inductive coil sensor significantly affected the quality of the measurement results, and that (2) P3 would be the most appropriate position for the textile-based inductive coil sensor for heart rate measurements based on the magnetic-induced conductivity sensing principle.

  20. Development and Characterization of Tissue Equivalent Proportional Counter for Radiation Monitoring in International Space Station

    Directory of Open Access Journals (Sweden)

    Uk-Won Nam

    2013-06-01

    Full Text Available Tissue equivalent proportional counter (TEPC can measure the Linear Energy Transfer (LET spectrum and calculate the equivalent dose for the complicated radiation field in space. In this paper, we developed and characterized a TEPC for radiation monitoring in International Space Station (ISS. The prototype TEPC which can simulate a 2 μm of the site diameter for micro-dosimetry has been tested with a standard alpha source (241Am, 5.5 MeV. Also, the calibration of the TEPC was performed by the 252Cf neutron standard source in Korea Research Institute of Standards and Science (KRISS. The determined calibration factor was kf = 3.59×10-7 mSv/R.

  1. INTERNAL FRICTION USE IN MONITORING THE DEGRADATION PROCESSES IN A MATERIAL

    Directory of Open Access Journals (Sweden)

    Peter Palček

    2011-10-01

    Full Text Available During the measurement of the fatigue life of material, the specimen undergoes large number of stress cycles. While the observed number of cycles before failure is considered to be the most important result (often the only one, more knowledge can be obtained. Measuring energy consumption of specimen during the cycling, the changes of microstructure of material (especially dislocation structure and crack initialization can be traced. The evolution of dynamic modulus can be watched on the same equipment. These information becomes very important, especially in the research of gigacycle fatigue strength and fatigue limit below which the continued loading does not lead to structural failure. In this article some remarks on microstructural changes in materials, which can be monitored by nondestructive measurement of internal friction are presented.

  2. Implementation of internal monitoring programs for workers occupationally exposed by 131I in nuclear medicine services in Brazil

    International Nuclear Information System (INIS)

    Oliveira, S.M.; Dantas, A.L.A.; Dantas, B.M.

    2017-01-01

    In nuclear medicine services (NMS), workers routinely handle radionuclides for diagnostic and therapy. This practice represents a risk of incorporation by these radionuclides. The International Atomic Energy Agency (IAEA) recommends the implementation of an internal monitoring program on workers exposed to annual effective doses greater than 1 mSv, as for example, those who handle 131 I for therapy in NMS. Currently, in Brazil, there are not enough available laboratories qualified to provide internal monitoring services to attend all possible demand of internal monitoring if it such regulation were applied by the Brazilian Nuclear Regulatory Board (CNEN). The objective of this work is to disseminate simple and inexpensive methods for in vivo routine thyroid monitoring of 131 I using equipment available in the NMS. Devices available in two public hospitals located in the city of Rio de Janeiro were calibrated for use in occupational internal monitoring. The equipment evaluated in this work presented enough sensitivity for such application, being suitable to access intakes of 131 I in the thyroid and able to estimate doses below 1 mSv. (author)

  3. Internalized Heterosexism among HIV-Positive, Gay-Identified Men: Implications for HIV Prevention and Care

    Science.gov (United States)

    Johnson, Mallory O.; Carrico, Adam W.; Chesney, Margaret A.; Morin, Stephen F.

    2008-01-01

    Internalized heterosexism (IH), or the internalization of societal antihomosexual attitudes, has been consistently linked to depression and low self-esteem among gay men, and it has been inconclusively associated with substance use and sexual risk in gay and bisexual men. Using structural equation modeling, the authors tested a model framed in…

  4. The International Law Commision at the End of Quinquennium: an Exceptional Session and Positive Results

    Czech Academy of Sciences Publication Activity Database

    Šturma, Pavel

    2016-01-01

    Roč. 7, nemá (2016), s. 437-450 ISSN 1805-0565. E-ISSN 1805-0999 Institutional support: RVO:68378122 Keywords : international law * International Law Commission * United Nations body Subject RIV: AG - Legal Sciences http://www.cyil.eu/

  5. Academic stress and positive affect: Asian value and self-worth contingency as moderators among Chinese international students.

    Science.gov (United States)

    Liao, Kelly Yu-Hsin; Wei, Meifen

    2014-01-01

    The theoretical model proposed by Berry and colleagues (Berry, 1997; Berry, Kim, Minde, & Mok, 1987) highlights the importance of identifying moderators in the acculturation process. Accordingly, the current study examined the Asian cultural value of family recognition through achievement (FRTA) and contingency of self-worth on academic competence (CSW-AC) as moderators in the association between academic stress and positive affect among Chinese international students. A total of 370 Chinese international students completed online surveys. Results from a hierarchical regression indicated that while academic stress was negatively associated with positive affect, FRTA was positively associated with positive affect. In other words, those with high academic stress reported a lower level of positive affect. However, individuals who endorsed high levels of FRTA reported a higher level of positive affect. In addition, results also revealed a significant interaction between academic stress and CSW-AC on positive affect. Thus, the study's finding supported the moderator role of CSW-AC. Simple effect analyses were conducted to examine the significant interaction. The results showed that higher levels of CSW-AC strengthened the negative association between academic stress and positive affect but lower levels of CSW-AC did not. Future research directions and implications are discussed.

  6. MONITORING TECHNOLOGY FOR EARLY DETECTION OF INTERNAL CORROSION FOR PIPELINE INTEGRITY

    Energy Technology Data Exchange (ETDEWEB)

    Glenn M. Light; Sang Y. Kim; Robert L. Spinks; Hegeon Kwun; Patrick C. Porter

    2003-09-01

    Transmission gas pipelines are an important part of energy-transportation infrastructure vital to the national economy. The prevention of failures and continued safe operation of these pipelines are therefore of national interest. These lines, mostly buried, are protected and maintained by protective coating and cathodic protection systems, supplemented by periodic inspection equipped with sensors for inspection. The primary method for inspection is ''smart pigging'' with an internal inspection device that traverses the pipeline. However, some transmission lines are however not suitable for ''pigging'' operation. Because inspection of these ''unpiggable'' lines requires excavation, it is cost-prohibitive, and the development of a methodology for cost-effectively assessing the structural integrity of ''unpiggable'' lines is needed. This report describes the laboratory and field evaluation of a technology called ''magnetostrictive sensor (MsS)'' for monitoring and early detection of internal corrosion in known susceptible sections of transmission pipelines. With the MsS technology, developed by Southwest Research Institute{reg_sign} (SwRI{reg_sign}), a pulse of a relatively low frequency (typically under 100-kHz) mechanical wave (called guided wave) is launched along the pipeline and signals reflected from defects or welds are detected at the launch location in the pulse-echo mode. This technology can quickly examine a long length of piping for defects, such as corrosion wastage and cracking in circumferential direction, from a single test location, and has been in commercial use for inspection of above-ground piping in refineries and chemical plants. The MsS technology is operated primarily in torsional guided waves using a probe consisting of a thin ferromagnetic strip (typically nickel) bonded to a pipe and a number of coil-turns (typically twenty or so turns) wound

  7. Development of capacitive beam position, beam current and Schottky-signal monitors for the Cryogenic Storage Ring (CSR)

    International Nuclear Information System (INIS)

    Laux, Felix

    2011-01-01

    In this thesis novel techniques based on capacitive pickups for the determination of the beam current, the beam position and the Schottky-signal in storage rings have been developed. Beam current measurements at the heavy ion storage ring TSR with a capacitive pickup have been found in very good agreement with the theory. Using this device the accurate measurement of beam currents at the TSR far below 1 μA is now possible. This method will also be used at the Cryogenic Storage Ring (CSR) at which beam currents in the range of 1 nA-1 μA are expected. For the first time, position measurements with a resonant amplifier system for capacitive pickups have been examined at the TSR for later use of this technique in the CSR. With this method an increased signal-to-noise ratio can be achieved using a parallel inductance. A comparison with measurements using the rest gas beam profile monitor has shown very good agreement even at very low intensities. Experiments with the cryo-capable electronics for the CSR beam position monitors have shown an achievable quality factor of Q=500, resulting in the prospect of precise position measurements at the CSR even at very low beam currents. The CSR Schottky-Pickup will also be equipped with a resonant amplifier system with a comparable quality factor. An estimation of the signal-to-noise ratio suggests a detection limit of a few protons. (orig.)

  8. High-rate RTK and PPP multi-GNSS positioning for small-scale dynamic displacements monitoring

    Science.gov (United States)

    Paziewski, Jacek; Sieradzki, Rafał; Baryła, Radosław; Wielgosz, Pawel

    2017-04-01

    The monitoring of dynamic displacements and deformations of engineering structures such as buildings, towers and bridges is of great interest due to several practical and theoretical reasons. The most important is to provide information required for safe maintenance of the constructions. High temporal resolution and precision of GNSS observations predestine this technology to be applied to most demanding application in terms of accuracy, availability and reliability. GNSS technique supported by appropriate processing methodology may meet the specific demands and requirements of ground and structures monitoring. Thus, high-rate multi-GNSS signals may be used as reliable source of information on dynamic displacements of ground and engineering structures, also in real time applications. In this study we present initial results of application of precise relative GNSS positioning for detection of small scale (cm level) high temporal resolution dynamic displacements. Methodology and algorithms applied in self-developed software allowing for relative positioning using high-rate dual-frequency phase and pseudorange GPS+Galileo observations are also given. Additionally, an approach was also made to use the Precise Point Positioning technique to such application. In the experiment were used the observations obtained from high-rate (20 Hz) geodetic receivers. The dynamic displacements were simulated using specially constructed device moving GNSS antenna with dedicated amplitude and frequency. The obtained results indicate on possibility of detection of dynamic displacements of the GNSS antenna even at the level of few millimetres using both relative and Precise Point Positioning techniques after suitable signals processing.

  9. New X-ray beam position monitors with submicron resolution utilizing imaging of scattered X-rays at CHESS

    International Nuclear Information System (INIS)

    Revesz, Peter; Temnykh, Alexander B.; Pauling, Alan K.

    2011-01-01

    At CHESS' A, F and G wiggler beam lines three new video beam position monitors (VBPMs) have been commissioned. These new VBPMs utilize X-rays scattered from the graphite filter (A and F line) or from a beryllium window (G-line) as the white wiggler beam passes through them. As the X-rays scatter in all directions from the scattering medium, a slit camera creates an image of the beam's footprint on a fluorescent screen. This image is then viewed by a CCD camera and analyzed using a computer program to calculate the intensity centroid, the beam profile and integrated intensity. These data are delivered to the CHESS signal archiving system for storage and display. The new systems employ digital cameras. These cameras are free of the noise inherent to the analog systems with long video signal connections. As a result, the beam position data delivered by the new systems are more reliable and accurate as shown by beam position traces using different beam position monitors on the same beam line.

  10. Monitoring internal corrosion in natural gas pipelines; Monitoracao da corrosao interna em gasodutos

    Energy Technology Data Exchange (ETDEWEB)

    Nobrega, Ana C.V.; Silva, Djalma R.; Pimenta, Gutemberg S. [Universidade Federal do Rio Grande do Norte, Natal, RN (Brazil); Barbosa, Andrea F.F. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil). Centro de Pesquisas

    2003-07-01

    For susceptibilities to the corrosion of the pipelines and equipment made in carbon steel and used by the natural gas, it makes be necessary to identify the acting corrosive agents and monitoring them along time, controlling failures for internal corrosion. Also, of that process it origins the black powder (solid particles) that can not commit the structural integrity of the equipment, but it can also bring the company other implications very serious, like quality of the sold product, as well as stops due to blockages and wastes for erosion of the equipment. The monitoring methodology and control of the corrosion in field consisted of the use of corrosion test equipment, chemical characterization of samples of black powder and liquids and analysis of the operational data of processes and plants. Like this, it was identified for the gas pipeline in analysis the most responsible parameters for the corrosive action of the fluid, establishing a controlling methodology and operational actions to maintain the corrosion rates at safe levels and structural warranty of the same. (author)

  11. PREFACE: 25th International Congress on Condition Monitoring and Diagnostic Engineering (COMADEM 2012)

    Science.gov (United States)

    Ball, Andrew; Mishra, Rakesh; Gu, Fengshou; Rao, Raj B. K. N.

    2012-05-01

    The proactive multidisciplinary conceptual philosophy of Condition Monitoring and Diagnostic Engineering Management (COMADEM) was conceived and has been nurtured, developed and sustained since 1988. Since then, it is gratifying to note that the condition monitoring, diagnostic and prognostic community worldwide (representing industrialists, academics, research and development organizations, professional/private establishments and many hardware/software vending organizations) has warmly welcomed and supported this venture. As is evidenced, many have reaped (and are reaping) the benefits of COMADEM interdiscipline through continuous knowledge discovery, generation and dissemination. We are now proud to celebrate the 25th Annual Event (Silver Jubilee) in Huddersfield, the most beautiful part of the United Kingdom. The theme of this Congress is 'Sustained Prosperity through Proactive Monitoring, Diagnosis, Prognosis and Management'. This proceedings is enriched by contributions from many keynote experts representing many industry and academic establishments worldwide. Authors from more than 30 different countries have pooled their rich multidisciplinary up-to-date knowledge, in order to share their invaluable experience with the COMADEM community. In this proceedings, the readers will find more than 120 refereed papers encompassing a number of topical areas of interest relating to the theme of the congress. The proceedings of COMADEM 2012 will appear in the Open Access Journal of Physics: Conference Series (JPCS), which is part of the IOP Conference Series. All papers published in the IOP Conference Series are fully citable and upon publication will be free to download. We would like to express our deep gratitude to all the keynote speakers, authors, referees, exhibitors, Technical Co-Sponsoring Organizations, Gold Sponsors, IOP Publishers, COMADEM 2012 organizing committee members, delegates and many others on whom the success of this prestigious event depends

  12. Scientific and technological monitoring: international overview on R. and D. related to Pra's

    International Nuclear Information System (INIS)

    Llory, M.; Stioui, A.

    1993-03-01

    In 1989, the R and D Division of Electricite de France launched a programme for a Technological and Scientific Overview (TSO) covering a certain number of topics considered to be important for the future of EDF. Probabilistic approaches to studies related to safety were considered to be strategically important to EDF, and therefore this area was selected for further study. A TSO is a process which can only start on the basis of a structured state-of-the-art organized as a basis of knowledge, together with the highlighting of a certain number of scientific and strategic ''set of references . The state-of-the-art of R and D related to Probabilistic Safety Assessment (PSA) was carried out in collaboration between the EDF R and D Division (SR branch) and SRI International. The approach chosen included: segmentation of the wide field of PSAs into subject areas, topics and sensitive points to be monitored; conception of a grid for the interviews; approximately thirty in-depth interviews of organizations and experts representative of the domain; analysis leading to identify certain problems areas or particularly important features. Emerging themes for research and further consideration in relation to PSAs, their application and their limits were also identified. Based on this state-of-the-art, various themes of monitoring were defined (living PSAs, limits of PSAs,...) and an organizational structure for monitoring was set up in the branch. The state of the art is not static, it is the reason why an in-depth extension of the study was undertaken on issues of special interest for EDF. (authors). 2 figs., 2 refs

  13. Materials International Space Station Experiment-6 (MISSE-6) Atomic Oxygen Fluence Monitor Experiment

    Science.gov (United States)

    Banks, Bruce A.; Miller, Sharon K.; Waters, Deborah L.

    2010-01-01

    An atomic oxygen fluence monitor was flown as part of the Materials International Space Station Experiment-6 (MISSE-6). The monitor was designed to measure the accumulation of atomic oxygen fluence with time as it impinged upon the ram surface of the MISSE 6B Passive Experiment Container (PEC). This was an active experiment for which data was to be stored on a battery-powered data logger for post-flight retrieval and analysis. The atomic oxygen fluence measurement was accomplished by allowing atomic oxygen to erode two opposing wedges of pyrolytic graphite that partially covered a photodiode. As the wedges of pyrolytic graphite erode, the area of the photodiode that is illuminated by the Sun increases. The short circuit current, which is proportional to the area of illumination, was to be measured and recorded as a function of time. The short circuit current from a different photodiode, which was oriented in the same direction and had an unobstructed view of the Sun, was also to be recorded as a reference current. The ratio of the two separate recorded currents should bear a linear relationship with the accumulated atomic oxygen fluence and be independent of the intensity of solar illumination. Ground hyperthermal atomic oxygen exposure facilities were used to evaluate the linearity of the ratio of short circuit current to the atomic oxygen fluence. In flight, the current measurement circuitry failed to operate properly, thus the overall atomic oxygen mission fluence could only be estimated based on the physical erosion of the pyrolytic graphite wedges. The atomic oxygen fluence was calculated based on the knowledge of the space atomic oxygen erosion yield of pyrolytic graphite measured from samples on the MISSE 2. The atomic oxygen fluence monitor, the expected result and comparison of mission atomic oxygen fluence based on the erosion of the pyrolytic graphite and Kapton H atomic oxygen fluence witness samples are presented in this paper.

  14. System for monitoring the position, intensity, uniformity, and directivity of a beam of ionizing radiation

    International Nuclear Information System (INIS)

    Boux, R.

    1976-01-01

    A monitoring device transparent to ionizing radiation, designed to measure the orientation, intensity and uniformity of an incident beam, comprises a cylindrical housing forming at least one ionization chamber with one or more ion-collecting electrodes transverse to the housing axis, each electrode being subdivided into a plurality of mutually insulated conductive elements connected to respective amplifiers. The elements of at least one electrode include one or more outer elements surrounding or bracketing one or more inner elements to measure the radiation in a central zone and a peripheral zone. The outputs of the respective amplifiers are additively and subtractively combined in an evaluation circuit

  15. Evaluation of sensitivity evaluation of a contamination monitor for use in monitoring of internal exposure of workers in nuclear medicine; Avaliacao da sensibilidade de um monitor de contaminacao para aplicacao em monitoracao da exposicao interna de trabalhadores em medicina nuclear

    Energy Technology Data Exchange (ETDEWEB)

    Dantas, Bernando Maranhao; Assis, Janima Cruz de; Oliveira, Salomao Marques de; Dantas, Ana Leticia Almeida, E-mail: bmdantas@ird.gov.br [Instituto de Radioprotecao e Dosimetria (IRD/CNEN-RJ), Rio de Janeiro, RJ (Brazil). Lab. de Monitoracao In Vivo. Div. de Dosimetria

    2014-07-01

    In practice of nuclear medicine, expert personnel routinely handle radiopharmaceuticals for diagnosis and radiotherapy. The control of intakes of radionuclides by workers can be performed through internal dosimetry techniques, as an integral part of the radiation protection program of the installation. The use of radiopharmaceuticals for diagnostic and therapeutic purposes in vivo and in vitro in Brazil is regulated by CNEN-NE Standards and 3:05 CNEN-NN 3.01. The International Atomic Energy Agency (IAEA) recommends the establishment of an internal monitoring program on workers, especially those subject to possible exposure to annual effective doses greater than 1 mSv. Note that, currently, in Brazil, are not available qualified laboratories to provide internal monitoring services in all regions in the country, if it were applied by CNEN, the requirement for internal monitoring of workers. This paper presents the development of a simple and low-cost methodology for in vivo monitoring of {sup 131}I in the thyroid. The proposed methodology is the use of portable monitor of surface contamination, equipment available and routinely used in all nuclear medicine services in Brazil. The monitor is calibrated with neck-thyroid simulator developed at the Laboratory of In Vivo Monitoring of IRD/CNEN-RJ. The equipment tested is suitable for application in in vivo occupational monitoring thyroid. This conclusion is based on the fact that the detection system has sufficient sensitivity for monitoring up to seven days after the incorporation of the radionuclide and guarantees {sup 131}I detection in values that result in effective doses below 1 mSv for the exposure scenarios adopted.

  16. Providing Books and Other Print Materials for Classroom and School Libraries. A Position Statement of the International Reading Association.

    Science.gov (United States)

    International Reading Association, Newark, DE.

    This position paper of the International Reading Association (IRA) calls for an immediate increase in funding for books in classroom, school, and town libraries. According to the paper, the condition of these libraries has weakened over the last decade--there are fewer books per child, and the condition of the books and the staffing of the…

  17. Internal and External Temperature Monitoring of a Li-Ion Battery with Fiber Bragg Grating Sensors

    Directory of Open Access Journals (Sweden)

    Susana Novais

    2016-08-01

    Full Text Available The integration of fiber Bragg grating (FBG sensors in lithium-ion cells for in-situ and in-operando temperature monitoring is presented herein. The measuring of internal and external temperature variations was performed through four FBG sensors during galvanostatic cycling at C-rates ranging from 1C to 8C. The FBG sensors were placed both outside and inside the cell, located in the center of the electrochemically active area and at the tab-electrode connection. The internal sensors recorded temperature variations of 4.0 ± 0.1 °C at 5C and 4.7 ± 0.1 °C at 8C at the center of the active area, and 3.9 ± 0.1 °C at 5C and 4.0 ± 0.1 °C at 8C at the tab-electrode connection, respectively. This study is intended to contribute to detection of a temperature gradient in real time inside a cell, which can determine possible damage in the battery performance when it operates under normal and abnormal operating conditions, as well as to demonstrate the technical feasibility of the integration of in-operando microsensors inside Li-ion cells.

  18. The United States as a Net Debtor Nation: Overview of the International Investment Position

    National Research Council Canada - National Science Library

    Jackson, James K

    2005-01-01

    ... foreigners own in the United States. These assets generate flows of capital into and out of the economy that have important implications for the value of the dollar in international exchange markets...

  19. The United States as a Net Debtor Nation: Overview of the International Investment Position

    National Research Council Canada - National Science Library

    Jackson, James K

    2007-01-01

    ... foreigners own in the United States. These assets generate flows of capital into and out of the economy that have important implications for the value of the dollar in international exchange markets...

  20. The United States as a Net Debtor Nation: Overview of the International Investment Position

    National Research Council Canada - National Science Library

    Jackson, James K

    2008-01-01

    ... foreigners own in the United States. These assets generate flows of capital into and out of the economy that have important implications for the value of the dollar in international exchange markets...

  1. Enterprise Marketing Risks Into the Selection by the Different Strategically Position Alternatives to the International Markets

    Directory of Open Access Journals (Sweden)

    Lucretia Mariana CONSTANTINESCU

    2012-11-01

    Full Text Available Entering into the international market is placed into the strategies area to geographical diversification which offer to companies a profitable source of growth. The “products – market/strategy” area is associated with the interdependency between the decisions that need to be made by strategic top management and also the strategic marketing of the company. For the strategies portfolio oriented to the business internalization of the company, the market risks are designed as a factor with important consequences to the marketing strategy of each company that depends on the hard reality of the competition on the international markets. This paper aims to analyze the different strategic risk categories to the companies that make the decision to be implemented on the external target-markets, thus compelling the companies to associate the international marketing opportunities within in a secondary objective connected to ensure the safety of the company shares for the choice of a new external market.

  2. Internalized HIV/AIDS-related stigma in a sample of HIV-positive people in Bangladesh.

    Science.gov (United States)

    Hasan, M Tanvir; Nath, Samir Ranjan; Khan, Nabilah S; Akram, Owasim; Gomes, Tony Michael; Rashid, Sabina F

    2012-03-01

    Internalized stigma among people living with HIV/AIDS (PLHA) is prevalent in Bangladesh. A better understanding of the effects of stigma on PLHA is required to reduce this and to minimize its harmful effects. This study employed a quantitative approach by conducting a survey with an aim to know the prevalence of internalized stigma and to identify the factors associated with internalized stigma among a sample of 238 PLHA (male=152 and female=86) in Bangladesh. The findings suggest that there is a significant difference between groups with the low- and the high-internalized HIV/AIDS stigma in terms of both age and gender. The prevalence of internalized stigma varied according to the poverty status of PLHA. An exploratory factor analysis (EFA) found 10 of 15 items loaded highly on the three factors labelled self-acceptance, self-exclusion, and social withdrawal. About 68% of the PLHA felt ashamed, and 54% felt guilty because of their HIV status. More than half (87.5% male and 19.8% female) of the PLHA blamed themselves for their HIV status while many of them (38.2% male and 8.1% female) felt that they should be punished. The male PLHA more frequently chose to withdraw themselves from family and social gatherings compared to the female PLHA. They also experienced a higher level of internalized stigma compared to the female PLHA. The results suggest that the prevalence of internalized stigma is high in Bangladesh, and much needs to be done by different organizations working for and with the PLHA to reduce internalized stigma among this vulnerable group.

  3. Towards a Long-Term Strategy for Voluntary-Based Internal Radiation Contamination Monitoring: A Population-Level Analysis of Monitoring Prevalence and Factors Associated with Monitoring Participation Behavior in Fukushima, Japan.

    Science.gov (United States)

    Nomura, Shuhei; Tsubokura, Masaharu; Ozaki, Akihiko; Murakami, Michio; Hodgson, Susan; Blangiardo, Marta; Nishikawa, Yoshitaka; Morita, Tomohiro; Oikawa, Tomoyoshi

    2017-04-09

    Following Japan's 2011 Fukushima nuclear incident, we assessed voluntary-based monitoring behavior in Minamisoma City-located 10-40 km from the Fukushima nuclear plant-to inform future monitoring strategies. The monitoring in Minamisoma included occasional free of charge internal-radiation-exposure measurements. Out of around 70,000 individuals residing in the city before the incident, a total of 45,788 residents (female: 52.1%) aged ≥21 were evaluated. The monitoring prevalence in 2011-2012 was only 30.2%, and this decreased to 17.9% in 2013-2014. Regression analyses were performed to estimate factors associated with the monitoring prevalence and participation behavior. The results show that, in comparison with the age cohort of 21-30 years, the cohort of 71-80 and ≥81 years demonstrated significantly lower monitoring prevalence; female residents had higher monitoring prevalence than male residents; those who were living in evacuation zones at the time of the incident had higher monitoring prevalence than those who lived outside any of the evacuation zones; for those living outside Fukushima and neighboring Prefectures post-incident monitoring prevalence decreased significantly in 2013-2014. Our findings inform the discussion on the concepts of radiation risk perception and accessibility to monitoring and societal decision-making regarding the maintenance of the monitoring program with low monitoring prevalence. We also stress the possibility that the monitoring can work both to check that internal contamination levels are within acceptable limits, and as a risk communication tool, alleviating individuals' concern and anxiety over radiation contamination.

  4. Empirical research on the internal audit position of companies in Serbia

    Directory of Open Access Journals (Sweden)

    Ljubisavljević Snežana

    2011-01-01

    Full Text Available In the context of the globalization of business operations and the increasing use of information technologies, complexity of business transactions, and business risk, the role of internal audit is becoming increasingly important and the range of tasks performed by internal auditors is growing. As a part of the company control system, the internal audit assesses the efficiency, effectiveness, economy, and fairness of the realization of tasks, provides consulting services to the enterprise’s management, and promotes the effectiveness of risk management with the aim of creating added value and enhancing business activities. It is the aim of this work, through empirical research conducted in large and medium-sized Serbian companies, to show the degree of development of the internal audit, the perception of accountants in respect to the tasks and responsibilities of internal audit, and whether there is a connection between the enterprise size and legal form on the one hand, and the organization and responsibilities of internal audit on the other.

  5. STUDENTS’ INFORMATION AND СOMMUNICATION COMPETENCE AS AN ASPECT OF MONITORING (OESD AND IEA INTERNATIONAL COMPARATIVE STUDY EXPERIENCE

    Directory of Open Access Journals (Sweden)

    Olena O. Hrytsenchuk

    2013-12-01

    Full Text Available The article deals the experience of the The International Association for the Evaluation of Educational Achievement - IEA and the Organisation for Economic Cooperation and Development - OECD in monitoring studies of students’ information and communication competence ( IC - competence of secondary schools, presented an analysis of common approaches to monitoring studies IC - competence of pupils in Europe at the present stage. There are identified peculiarities, common trends and future development.

  6. An intelligent portal monitor for fast suppression of false positives due to radiopharmaceuticals

    International Nuclear Information System (INIS)

    Johnson, M.W.; Butterfield, K.B.

    1985-01-01

    Monitoring the movement of radioactive material through secure or sensitive areas may be complicated by the existence of unanticipated sources of radiation carried by individuals passing through the area. Typical of such sources are radiopharmaceuticals prescribed for a medical procedure. The authors report here on an apparatus designed to quickly discriminate between in-vivo radiopharmaceuticals and other nuclear materials, based on a pattern-recognition algorithm and microcomputer. Principles of operation are discussed, and the data base for the pattern-recognition algorithms is displayed. Operating experience with the apparatus in a trial location is also discussed. The apparatus correctly identifies in-vivo radiopharmaceuticals in over 80% of all trials; challenges with radioisotopes other than radiopharmaceuticals have led the apparatus, without exception, to reject the challenge isotope as incompatible with medical practice. The apparatus thus rapidly discriminates between individuals bearing radiopharmaceuticals and those bearing illicit sources, such as special nuclear materials

  7. Occupational exposure to ultrafine particles among airport employees--combining personal monitoring and global positioning system

    DEFF Research Database (Denmark)

    Møller, Karina Lauenborg; Thygesen, Lau Caspar; Schipperijn, Jasper

    2014-01-01

    at several airports, especially on the apron, but knowledge on individual exposure profiles among different occupational groups working at an airport is lacking. PURPOSE: The aim of this study was to compare personal exposure to UFP among five different occupational groups working at Copenhagen Airport (CPH......). METHOD: 30 employees from five different occupational groups (baggage handlers, catering drivers, cleaning staff and airside and landside security) at CPH were instructed to wear a personal monitor of particle number concentration in real time and a GPS device. The measurements were carried out on 8 days...... distributed over two weeks in October 2012. The overall differences between the groups were assessed using linear mixed model. RESULTS: Data showed significant differences in exposure levels among the groups when adjusted for variation within individuals and for effect of time and date (p

  8. Reproducibility of a Noninvasive System for Eye Positioning and Monitoring in Stereotactic Radiotherapy of Ocular Melanoma.

    Science.gov (United States)

    Iskanderani, Omar; Béliveau-Nadeau, Dominique; Doucet, Robert; Coulombe, Geneviève; Pascale, Deborah; Roberge, David

    2017-06-01

    Our preferred treatment for juxtapapillary choroidal melanoma is stereotactic radiotherapy. We aim to describe our immobilization system and quantify its reproducibility. Patients were identified in our radiosurgery database. Patients were imaged at computed tomography simulator with an in-house system which allows visual monitoring of the eye as the patient fixates a small target. All patients were reimaged at least once prior to and/or during radiotherapy. The patients were treated on the CyberKnife system, 60 Gy in 10 daily fractions, using skull tracking in conjunction with our visual monitoring system. In order to quantify the reproducibility of the eye immobilization system, computed tomography scans were coregistered using rigid 6-dimensional skull registration. Using the coregistered scans, x, y, and z displacements of the lens/optic nerve insertion were measured. From these displacements, 3-dimensional vectors were calculated. Thirty-four patients were treated from October 2010 to September 2015. Thirty-nine coregistrations were performed using 73 scans (2-3 scans per patient). The mean displacements of lens and optic nerve insertion were 0.1 and 0.0 mm. The median 3-dimensional displacements (absolute value) of lens and nerve insertion were 0.8 and 0.7 mm (standard deviation: 0.5 and 0.6 mm). Ninety-eight percent of 3-dimensional displacements were below 2 mm (maximum 2.4 mm). The calculated planning target volume (PTV) margins were 0.8, 1.4, and 1.5 mm in the anterior-posterior, craniocaudal, and right-left axes, respectively. Following this analysis, no further changes have been applied to our planning margin of 2 to 2.5 mm as it is also meant to account for uncertainties in magnetic resonance imaging to computed tomography registration, skull tracking, and also contouring variability. We have found our stereotactic eye immobilization system to be highly reproducible (<1 mm) and free of systematic error.

  9. THE TEST PROGRAMME CONCERNING AIRCRAFT POSITIONING AND TRAFFIC MONITORING – PART II

    Directory of Open Access Journals (Sweden)

    Henryk JAFERNIK

    2016-12-01

    Full Text Available This paper presents the results of studies on the determination of an aircraft’s trajectory and positioning accuracy. The PPP method was applied to determine the aircraft’s position in kinematic mode for code observations in the GPS system. Computations were executed in the “PPP_KINEMTIC” software, whose source code was written using the Scilab 5.3.2 platform. The PPP_KINEMTIC software allows for the latitude coordinate to be estimated with accuracy between 1 and 6 m, the longitude coordinate to be estimated with accuracy between 0.5 and 2.5 m, and the ellipsoidal height to be estimated with accuracy between 1 and 7 m. The average value of the MRSE term equals 5 m with a magnitude between 1 and 8.5 m. In the paper, general libraries of the PPP_KINEMTIC application were presented and the PPP method was characterized too.

  10. Solar Eclipse Monitoring for Solar Energy Applications Using the Solar and Moon Position Algorithms

    Energy Technology Data Exchange (ETDEWEB)

    Reda, I.

    2010-03-01

    This report includes a procedure for implementing an algorithm (described by Jean Meeus) to calculate the moon's zenith angle with uncertainty of +/-0.001 degrees and azimuth angle with uncertainty of +/-0.003 degrees. The step-by-step format presented here simplifies the complicated steps Meeus describes to calculate the Moon's position, and focuses on the Moon instead of the planets and stars. It also introduces some changes to accommodate for solar radiation applications.

  11. Development of an expert system for the taking into account of uncertainties in the monitoring of internal contaminations

    International Nuclear Information System (INIS)

    Davesne, E.; Blanchardon, E.; Casanova, P.; Chojnacki, E.; Paquet, F.

    2010-01-01

    Internal contaminations may result from professional exposure and they can be monitored by anthropo-radiometric and radio-toxicological measurements which are interpreted in terms of embedded activity and effective dose by means of biokinetic and dosimetric models. In spite of standards, some uncertainties in the dosimetric interpretation of radio-toxicological measurements may remain. The authors report the development of a software (OPSCI code) which takes into account uncertainties related to the worker internal dosimetry, the calculation of the minimum detectable dose related to an exposure, and the development of a data monitoring programme

  12. A novel diamond-based beam position monitoring system for the High Radiation to Materials facility at CERN SPS

    CERN Document Server

    AUTHOR|(CDS)2092886; Höglund, Carina

    The High Radiation to Materials facility employs a high intensity pulsed beam imposing several challenges on the beam position monitors. Diamond has been shown to be a resilient material with its radiation hardness and mechanical strength, while it is also simple due to its wide bandgap removing the need for doping. A new type of diamond based beam position monitor has been constructed, which includes a hole in the center of the diamond where the majority of the beam is intended to pass through. This increases the longevity of the detectors as well as allowing them to be used for high intensity beams. The purpose of this thesis is to evaluate the performance of the detectors in the High Radiation to Materials facility for various beam parameters, involving differences in position, size, bunch intensity and bunch number. A prestudy consisting of calibration of the detectors using single incident particles is also presented. The detectors are shown to work as intended after a recalibration of the algorithm, alb...

  13. In-situ monitoring of pitting corrosion on vertically positioned 304 stainless steel by analyzing acoustic-emission energy parameter

    International Nuclear Information System (INIS)

    Wu, Kaige; Jung, Woo-Sang; Byeon, Jai-Won

    2016-01-01

    Highlights: • Pitting process in vertically positioned 304 SS is investigated by AE energy. • Gravity-influenced elongated pit, crack and rupture of pit cover were observed. • Hydrogen bubble evolution and pit covers rupturing were separately monitored by AE. • Four stages of AE energy were correlated with observed pitting mechanism. - Abstract: The acoustic emission (AE) energy was analyzed to monitor the pitting process on a vertically positioned 304-stainless steel. The gravity-dependent morphology of the elongated corrosion pits was observed. A scatter plot of the duration and energy indicated two AE clusters with different energy levels. There was a time delay after the detection of the low-energy hydrogen-bubble signals. Subsequently, high-energy signals were observed, whose AE source was attributed to large-scale cracks formed during the rupture of the elongated pit cover. An in-situ analysis of the AE energy evolution provided detailed insights into the corrosion process in relation to the specimen position.

  14. The international competitive position of the Dutch top sectors; De internationale concurrentiepositie van de topsectoren

    Energy Technology Data Exchange (ETDEWEB)

    Raspe, O.; Weterings, A.; Thissen, M.

    2012-03-15

    Creating an excellent investment climate for the Dutch top sectors; that is the strategy of the Dutch government to improve the economic competitiveness of the Netherlands. In this endeavour, the Dutch cabinet is advised by ten top teams. With this study, the Environmental Assessment Agency (PBL) aims to supplement the action agendas of the top teams, which mainly involve generic and sector-specific measures. Based on empirical know-how and quantitative analysis of the competitive position of the top sectors within Europe, PBL shows that characteristics of the regional business climate are particularly important for the international competitiveness of the top sectors. A benchmark of 250 European regions shows how the Dutch regions score as compared to their most important competitors in Europe. This benchmark shows that drawing up the investment agenda for the Dutch top sectors is tailored work. For example, for the top sector energy in South Holland, it is important to invest in a strong private knowledge base (research and development by businesses). For the top sector logistics in North Holland, on the other hand, a better connectivity by road is important. For the high-tech businesses in Noord-Brabant, strengthening the high-tech cluster in this region would be beneficial. Therefore, PBL recommends a spatial-economic vision on the competitive powers of the top sectors. This vision should focus on priority areas North Holland and South Holland, and on crucial connections such as Schiphol and the highways 'Triple A', A2, A4 and A12. [Dutch] Een excellent vestigingsklimaat creëren voor de topsectoren. Dat is de strategie van het kabinet-Rutte om de economische concurrentiekracht van Nederland te verbeteren. Het kabinet laat zich daarbij adviseren door tien topteams. Met deze studie wil het Planbureau voor de Leefomgeving (PBL) een aanvulling bieden op de actieagenda's van de topteams, die vooral generieke en sectorspecifieke maatregelen betreffen

  15. Monitoring system and methods for a distributed and recoverable digital control system

    Science.gov (United States)

    Stange, Kent (Inventor); Hess, Richard (Inventor); Kelley, Gerald B (Inventor); Rogers, Randy (Inventor)

    2010-01-01

    A monitoring system and methods are provided for a distributed and recoverable digital control system. The monitoring system generally comprises two independent monitoring planes within the control system. The first monitoring plane is internal to the computing units in the control system, and the second monitoring plane is external to the computing units. The internal first monitoring plane includes two in-line monitors. The first internal monitor is a self-checking, lock-step-processing monitor with integrated rapid recovery capability. The second internal monitor includes one or more reasonableness monitors, which compare actual effector position with commanded effector position. The external second monitor plane includes two monitors. The first external monitor includes a pre-recovery computing monitor, and the second external monitor includes a post recovery computing monitor. Various methods for implementing the monitoring functions are also disclosed.

  16. An Evaluation of Two Internal Surrogates for Determining the Three-Dimensional Position of Peripheral Lung Tumors

    International Nuclear Information System (INIS)

    Spoelstra, Femke; Soernsen de Koste, John R. van; Vincent, Andrew; Cuijpers, Johan P.; Slotman, Ben J.; Senan, Suresh

    2009-01-01

    Purpose: Both carina and diaphragm positions have been used as surrogates during respiratory-gated radiotherapy. We studied the correlation of both surrogates with three-dimensional (3D) tumor position. Methods and Materials: A total of 59 repeat artifact-free four-dimensional (4D) computed tomography (CT) scans, acquired during uncoached breathing, were identified in 23 patients with Stage I lung cancer. Repeat scans were co-registered to the initial 4D CT scan, and tumor, carina, and ipsilateral diaphragm were manually contoured in all phases of each 4D CT data set. Correlation between positions of carina and diaphragm with 3D tumor position was studied by use of log-likelihood ratio statistics. Models to predict 3D tumor position from internal surrogates at end inspiration (EI) and end expiration (EE) were developed, and model accuracy was tested by calculating SDs of differences between predicted and actual tumor positions. Results: Motion of both the carina and diaphragm significantly correlated with tumor motion, but log-likelihood ratios indicated that the carina was more predictive for tumor position. When craniocaudal tumor position was predicted by use of craniocaudal carina positions, the SDs of the differences between the predicted and observed positions were 2.2 mm and 2.4 mm at EI and EE, respectively. The corresponding SDs derived with the diaphragm positions were 3.7 mm and 3.9 mm at EI and EE, respectively. Prediction errors in the other directions were comparable. Prediction accuracy was similar at EI and EE. Conclusions: The carina is a better surrogate of 3D tumor position than diaphragm position. Because residual prediction errors were observed in this analysis, additional studies will be performed using audio-coached scans.

  17. The internal model: A study of the relative contribution of proprioception and visual information to failure detection in dynamic systems. [sensitivity of operators versus monitors to failures

    Science.gov (United States)

    Kessel, C.; Wickens, C. D.

    1978-01-01

    The development of the internal model as it pertains to the detection of step changes in the order of control dynamics is investigated for two modes of participation: whether the subjects are actively controlling those dynamics or are monitoring an autopilot controlling them. A transfer of training design was used to evaluate the relative contribution of proprioception and visual information to the overall accuracy of the internal model. Sixteen subjects either tracked or monitored the system dynamics as a 2-dimensional pursuit display under single task conditions and concurrently with a sub-critical tracking task at two difficulty levels. Detection performance was faster and more accurate in the manual as opposed to the autopilot mode. The concurrent tracking task produced a decrement in detection performance for all conditions though this was more marked for the manual mode. The development of an internal model in the manual mode transferred positively to the automatic mode producing enhanced detection performance. There was no transfer from the internal model developed in the automatic mode to the manual mode.

  18. Phase acceleration: a new important parameter in GPS occultation monitoring of the atmospheric internal waves

    Science.gov (United States)

    Pavelyev, A. G.; Liou, Y. A.; Wickert, J.; Schmidt, T.; Pavelev, A. A.; Gubenko, V. N.

    2009-04-01

    After forty years of radio occultation (RO) experiments it is clear now that the phase acceleration of radio waves has the same importance as the Doppler frequency. This was shown by use of analysis of high-stability GPS RO signals. Phase acceleration technique allows one to convert the phase and Doppler frequency changes to the refraction attenuation variations. From the derived refraction attenuation one can estimate the integral absorption of radio waves by use of the amplitude data. This is important for measurement of water vapor and minor atmospheric gas constituents in future RO missions because of excluding the difficulty with removing the refraction attenuation effect from the amplitude data. Phase acceleration/intensity technique can be applied to separate the influence of layered structures from contributions of irregularities and turbulence in the atmosphere and ionosphere. Phase acceleration/intensity technique can be applied also for location and determination of the height and inclination of the layered structures in the atmosphere and ionosphere. In many cases the layered structures in the atmosphere indicate quasi-periodical altitude dependence that reveals their wave origin. The altitude profile of the vertical gradient of refractivity of the layered structures can be used to find the main characteristics of the internal wave activity with a global coverage. In general case, when the type of internal waves are not known, the height dependence of the vertical gradient of refractivity can be applied for monitoring the seasonal and geographical distributions of wave activity at different levels in the atmosphere. In the case of the internal gravity waves (GW) one can measure important GW parameters by use of the vertical profile of the refractivity: the intrinsic phase speed, the horizontal wind perturbations and, under some assumptions, the intrinsic frequency as functions of height in the atmosphere. Advantages of the phase acceleration

  19. Project of a beam position monitor for the ESRF storage ring

    International Nuclear Information System (INIS)

    Loyer, F.; Scheidt, K.

    1992-01-01

    The realisation of the ESRF design objectives demands new standards of precision and reproductibility for the closed orbit correction which require a BPM system with functionality and performances of superior quality. To guarantee difficult performance characteristic, all sources of error have been analysed: Qpole magnetic axis measurement, BPM block mechanical position, BPM block electrical offset and offset of electronics signal treatment. The choice of the concept (RF time multiplexing of the 4 electrode signals) to keep these errors to a minimum and the method used to further eliminate them are described. The complete electronics treatment chain and the performances obtained in laboratory is presented. (R.P.) 3 refs.; 5 figs

  20. An alarm instrument for monitoring leakage of oil storage tanks and the location of their leak position using radioisotope tracers

    International Nuclear Information System (INIS)

    Lu Qingqian; Sun Xiaolei; Hu Xusheng

    1990-01-01

    Usually it is difficult to find out gasoline leakage at the bottom of a storage tank from the very beginning. In order to solve this problem, a leak-monitoring technique and an instrument based on the detection of nuclear radiation have been successfully developed. The instrument possesses high sensitivity, short reaction time, excellent stability and rellability. When very small leaks at the bottom of a tank appear, the instrument will show a leak signal and give an alarm. In the meantime, however, the tank can be still used until the preparations for repairing are completed. Then its leak position can be accurately located by using radioisotope tracers

  1. Intelligent portal monitor for fast suppression of false positives due to radiopharmaceuticals

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, M.W.; Butterfield, K.B.

    1985-01-01

    Monitoring the movement of radioactive material through secure or sensitive areas may be complicated by the existence of unanticipated sources of radiation carried by individuals passing through the area. Typical of such sources are radiopharmaceuticals prescribed for a medical procedure. We report here on an apparatus designed to quickly discriminate between in-vivo radiopharmaceuticals and other nuclear materials, based on a pattern-recognition algorithm and a microcomputer. Principles of operation are discussed, and the data base for the pattern-recognition algorithm is displayed. Operating experience with the apparatus in a trial location is also discussed. Our apparatus correctly identifies in-vivo radiopharmaceuticals in over 80% of all trials; challenges with radioisotopes other than radiopharmaceuticals have led the apparatus, without exception, to reject the challenge isotope as incompatible with medical practice. The apparatus thus rapidly discriminates between individuals bearing radiopharmaceuticals and those bearing illicit sources, such as special nuclear materials. Examples of applications are presented. 7 refs., 4 figs., 1 tab.

  2. Social assessment of wind power. Part 4: International position and development conditions of the Danish wind turbine industry

    International Nuclear Information System (INIS)

    Karnoee, P.; Joergensen, U.

    1995-12-01

    Today, the Danish wind turbine industry is positioned as a global market leader on a fast growing international market. The conclusion and observation of this report are: 1. The international market for wind power is likely to grow fast over the next 5 years (a self-reinforcing development) and the Danish wind turbine industry has the potential to increase export from the present DKK 2 billion per year to DKK 4 billion per year. 2. The leading market position is achieved after the collapse of the California market in 1987. The last four years have been export-driven growth together with the development of complementary assets to support a strong product technology. 3. The Danish position might be threatened by the new competitors, but it is our view that it takes 2-3 years before they have equivalent competences, and since the Danish companies are presently also mobilizing resources and competences it is not likely that they are easily outperformed. 4. A continued installation of wind power in Denmark is important to support the sustaining of the international position in the coming years. Through, it is not the volume size of the domestic market, but rather a stable market which serves as a home base for the industry. Not only for the reference and testing of new wind turbines, but also the knowledge networks between manufacturers and suppliers and between manufacturers and the Test Station for Windmills at Risoe. (EG) 51 refs

  3. Monitoring and evaluation of human resources for health: an international perspective

    Directory of Open Access Journals (Sweden)

    Gupta Neeru

    2003-04-01

    Full Text Available Abstract Background Despite the undoubted importance of human resources to the functions of health systems, there is little consistency between countries in how human resource strategies are monitored and evaluated. This paper presents an integrated approach for developing an evidence base on human resources for health (HRH to support decision-making, drawing on a framework for health systems performance assessment. Methods Conceptual and methodological issues for selecting indicators for HRH monitoring and evaluation are discussed, and a range of primary and secondary data sources that might be used to generate indicators are reviewed. Descriptive analyses are conducted drawing primarily on one type of source, namely routinely reported data on the numbers of health personnel and medical schools as covered by national reporting systems and compiled by the World Health Organization. Regression techniques are used to triangulate a given HRH indicator calculated from different data sources across multiple countries. Results Major variations in the supply of health personnel and training opportunities are found to occur by region. However, certain discrepancies are also observed in measuring the same indicator from different sources, possibly related to the occupational classification or to the sources' representation. Conclusion Evidence-based information is needed to better understand trends in HRH. Although a range of sources exist that can potentially be used for HRH assessment, the information that can be derived from many of these individual sources precludes refined analysis. A variety of data sources and analytical approaches, each with its own strengths and limitations, is required to reflect the complexity of HRH issues. In order to enhance cross-national comparability, data collection efforts should be processed through the use of internationally standardized classifications (in particular, for occupation, industry and education at the

  4. Towards a Long-Term Strategy for Voluntary-Based Internal Radiation Contamination Monitoring: Representativeness of the Monitoring Results in Fukushima, Japan.

    Science.gov (United States)

    Nomura, Shuhei; Tsubokura, Masaharu; Murakami, Michio; Ono, Kyoko; Nishikawa, Yoshitaka; Oikawa, Tomoyoshi

    2017-06-20

    Following Japan's 2011 Fukushima nuclear incident, voluntary participation, rather than mandatory, was adopted as the default scenario for individual radiation monitoring. We evaluated the representativeness of the internal monitoring results from voluntary participants in Minamisoma City, which is located 10-40 km from the Fukushima nuclear plant. Of approximately 70,000 individuals who were residing in Minamisoma City before the incident, a total of 19,263 residents (aged ≥21 years) participated in the monitoring from 1 October 2011 to 31 March 2015. Based on regression projection techniques with the available data obtained from the voluntary participants, the modeled probabilities of radiocesium (Cs) detection in October 2011 for Cs-137 and Cs-134 were 66.9% and 52.9%, respectively, which declined dramatically within a year following the incident. The rate of decline had stagnated since mid-2012, and the probability was close to zero after mid-2014. Sufficient agreement between the modeled probabilities of Cs detection (for the whole population) versus the measured Cs levels (for voluntary participants) was observed, except for Cs-134 in October 2011, indicating that the voluntary monitoring participant group was a good representative sample. Our findings affirmed the clinical importance of voluntary-based monitoring as a screening and dose-assessment tool in a post-nuclear incident. Our study informs societal decision-making regarding the long-term maintenance of the monitoring program under the current low exposure levels.

  5. Web-based continuous internal corrosion monitoring of a sweet natural gas pipeline

    Energy Technology Data Exchange (ETDEWEB)

    Cauchi, Sam; Vorozcovs, Andrew [Fiber Optic Systems Technology Inc. (FOX-TEK), Bedford, Nova Scotia (Canada)

    2009-07-01

    Inspection of pipelines susceptible to internal corrosion is a key ingredient in maintaining their reliable throughput. While conventional inspection consisting of in line inspection, radiography and ultrasound remain the mainstay of most integrity programs, challenging circumstances in some cases make the availability of such data inadequate, cost prohibitive, and at times entirely unavailable. These scenarios include aggressive internal corrosion, expensive excavation conditions, low or stagnant flow, and non-piggable pipeline segments. While some gas pipelines in these circumstances are considered relatively low risk and low consequence, due to the significant reclamation costs and cleanup time associated with liquid pipelines, those areas identified as being high-risk are often high-consequence and thus require a specialized inspection solution. For areas deemed to be at high-risk, or areas of low-risk with high consequence, Electrical Field Mapping (EFM) has provided a practical solution to safe operation without introducing expensive and potentially dangerous dig programs. Historically, however, this inspection approach has required manual data acquisition as part of a scheduled EFM site visit schedule. Due to the tedious nature of this data acquisition approach, the remoteness of some pipeline inspection sites and the complexity of data analysis, it has been difficult to closely monitor the most critical assets on a continuous basis. The manual component of this approach also often eliminates EFM as a practical solution due to lack of properly trained personnel. In this paper, we will discuss a new approach to data acquisition where data is acquired, transmitted, analyzed, and displayed completely automatically and remotely with virtually no human overhead or recurring operating costs. An overview of the PinPoint monitoring setup covering 180 degrees of pipe circumference is described. This advanced EFM system allows operators to observe, essentially in real

  6. A Prospective Cohort Study of Gated Stereotactic Liver Radiation Therapy Using Continuous Internal Electromagnetic Motion Monitoring.

    Science.gov (United States)

    Worm, Esben S; Høyer, Morten; Hansen, Rune; Larsen, Lars P; Weber, Britta; Grau, Cai; Poulsen, Per R

    2018-02-13

    Intrafraction motion can compromise the treatment accuracy in liver stereotactic body radiation therapy (SBRT). Respiratory gating can improve treatment delivery; however, gating based on external motion surrogates is inaccurate. The present study reports the use of Calypso-based internal electromagnetic motion monitoring for gated liver SBRT. Fifteen patients were included in a study of 3-fraction respiratory gated liver SBRT guided by 3 implanted electromagnetic transponders. The planning target volume was created by a 5-mm axial and 7-mm (n = 12) or 10-mm (n = 3) craniocaudal expansion of the clinical target volume (CTV) and covered with 67% of the prescribed CTV mean dose. Treatment was gated to the end-exhale phase of the respiratory cycle with beam-on when the target deviated 1 to 2 mm occurred. Log files of transponder motion were used to determine the geometric error and reconstruct the delivered CTV dose in the actual gated treatments and in simulated nongated treatments. No severe side effects were observed in relation to transponder implantation. All 45 treatment fractions were successfully guided using the Calypso system. The mean number of couch corrections during each gated fraction was 2.8 (range 0-7). The mean duty cycle during gated treatment was 62.5% (range 29.1%-84.9%). Without gating, the mean 3-dimensional geometric error during a fraction would have been 5.4 mm (range 2.7-12.1). Gating reduced this error to 2.0 mm (range 1.2-3.0). The patient mean reduction in minimum dose to 95% of the CTV relative to the planned dose was 6.0 percentage points (range 0.7-22.0) without gating and 0.8 percentage point (range 0.2-2.0) with gating. Gating using internal motion monitoring was successfully applied for liver SBRT. It markedly improved the geometric and dosimetric accuracy compared with nongated standard treatment. Copyright © 2018 Elsevier Inc. All rights reserved.

  7. Japan's position in international climate policy: navigating between Kyoto and the APP

    NARCIS (Netherlands)

    van Asselt, H.D.; Kanie, N.; Iguchi, M.

    2009-01-01

    The emergence of technology-oriented agreements such as the 2005 Asia-Pacific Partnership on Clean Development and Climate (APP) may have significant implications for the future of global climate governance, as these agreements could be perceived as an alternative for the existing international

  8. Ultrasonic thickness structural health monitoring photoelastic visualization and measurement accuracy for internal pipe corrosion

    Science.gov (United States)

    Eason, Thomas J.; Bond, Leonard J.; Lozev, Mark G.

    2015-03-01

    Oil refinery production of fuels is becoming more challenging as a result of the changing world supply of crude oil towards properties of higher density, higher sulfur concentration, and higher acidity. One such production challenge is an increased risk of naphthenic acid corrosion that can result in various surface degradation profiles of uniform corrosion, non-uniform corrosion, and localized pitting in piping systems at temperatures between 150°C and 400°C. The irregular internal surface topology and high external surface temperature leads to a challenging in-service monitoring application for accurate pipe wall thickness measurements. Improved measurement technology is needed to continuously profile the local minimum thickness points of a non-uniformly corroding surface. The measurement accuracy and precision must be sufficient to provide a better understanding of the integrity risk associated with refining crude oils of higher acid concentration. This paper discusses potential technologies for measuring localized internal corrosion in high temperature steel piping and describes the approach under investigation to apply flexible ultrasonic thin-film piezoelectric transducer arrays fabricated by the sol-gel manufacturing process. Next, the elastic wave beam profile of a sol-gel transducer is characterized via photoelastic visualization. Finally, the variables that impact measurement accuracy and precision are discussed and a maximum likelihood statistical method is presented and demonstrated to quantify the measurement accuracy and precision of various time-of-flight thickness calculation methods in an ideal environment. The statistical method results in confidence values analogous to the a90 and a90/95 terminology used in Probability-of-Detection (POD) assessments.

  9. The effectiveness of cerebral oxygenation monitoring during arthroscopic shoulder surgery in the beach chair position: a randomized blinded study.

    Science.gov (United States)

    Cox, Ryan M; Jamgochian, Grant C; Nicholson, Kristen; Wong, Justin C; Namdari, Surena; Abboud, Joseph A

    2018-04-01

    Beach chair positioning for shoulder surgery is associated with measurable cerebral desaturation events (CDEs) in up to 80% of patients. Near-infrared spectroscopy (NIRS) technology allows real-time measurement of cerebral oxygenation and may minimize the frequency of CDEs. The purpose of this study was to investigate the incidence of CDEs when anesthetists were aware of and blinded to NIRS monitoring and to determine the short-term cognitive effects of surgery in the beach chair position. NIRS was used to monitor cerebral oxygenation saturation in 41 consecutive patients undergoing arthroscopic shoulder surgery in the beach chair position. Patients were randomized to 2 groups, anesthetists aware of or blinded to NIRS data. The Montreal Cognitive Assessment (MoCA) was used to assess cognitive function preoperatively, immediately postoperatively, and at 2 and 6 weeks postoperatively. Overall, 7 (17.5%) patients experienced a CDE, 5 (25%) in the aware group and 2 (10%) in the blinded group. There was no significant difference in MoCA scores between the aware and blinded groups preoperatively (27.9.1 vs. 28.2; P = .436), immediately postoperatively (26.1 vs. 26.2; P = .778), 2 weeks postoperatively (28.0 vs. 28.1; P = .737), or 6 weeks postoperatively (28.5 vs. 28.4; P = .779). There was a correlation of NIRS with systolic blood pressure (r = 0.448), diastolic blood pressure (r = 0.708), and mean arterial pressure (r = 0.608). In our series, the incidence of CDEs was much lower than previously reported and was not lowered by use of NIRS. Patients did not have significant cognitive deficits after arthroscopic surgery in the beach chair position, and there was a correlation between NIRS and intraoperative brachial blood pressure. Copyright © 2017 Journal of Shoulder and Elbow Surgery Board of Trustees. Published by Elsevier Inc. All rights reserved.

  10. Retrospective analysis of the associations and effectiveness of performing therapeutic drug monitoring in pregnant HIV-positive women in two large centres in Manchester.

    Science.gov (United States)

    Whitfield, Thomas; Dessain, Amabel; Taylor, Kelly; McQuillan, Orla; Kingston, Margaret; Ajdukiewicz, Katherine

    2017-04-01

    There is no proven benefit for the routine use of therapeutic drug monitoring in HIV-positive pregnant women either for improving viral control or preventing mother-to-child transmission. This analysis reviewed a cohort of 171 HIV-positive pregnant women delivering between 1 January 2008 and 28 May 2013 to first establish which baseline characteristics are associated with having therapeutic drug monitoring performed, and whether therapeutic drug monitoring was associated with improved HIV control during pregnancy or mother-to-child transmission. Therapeutic drug monitoring was performed in 39% ( n = 66) of patients; it was associated with baseline characteristics of poor adherence to therapy (therapeutic drug monitoring 23% versus non-therapeutic drug monitoring 10%, p = 0.025) and the use of protease inhibitors (therapeutic drug monitoring 94% versus non-therapeutic drug monitoring 77%, p = 0.005). By multivariate analysis therapeutic drug monitoring was associated with medication alterations during pregnancy (therapeutic drug monitoring 68% versus non-therapeutic drug monitoring 12%, p = < 0.001), but not associated with any difference in viral load breakthrough during pregnancy (therapeutic drug monitoring 12% versus non-therapeutic drug monitoring 7%, p = 0.456) and viral load detectable at birth (therapeutic drug monitoring 14% versus non-therapeutic drug monitoring 9%, p = 0.503). There were no instances of mother-to-child transmission. Therapeutic drug monitoring's association with medication changes is postulated as partially causal in this cohort. There was no evidence of any association with improved control or reduced transmission of HIV to advocate routine therapeutic drug monitoring use.

  11. Development of a highly sensitive current and position monitor with HTS squids and an HTS magnetic shield

    International Nuclear Information System (INIS)

    Watanabe, T.; Ikeda, T.; Kase, M.; Yano, Y.; Watanabe, S.; Sasaki, Y.; Kawaguchi, T.

    2005-01-01

    A highly sensitive current and position monitor with HTS (High-Temperature Superconducting) SQUIDs (Superconducting QUantum Interference Device) and an HTS magnetic shield for the measurement of the intensity of faint beams, such as a radioisotope beam, has been developed for the RIKEN RI beam factory project. The HTS magnetic shield and the HTS current sensor including the HTS SQUID are cooled by a low-vibration pulse-tube refrigerator. Both the HTS magnetic shield and the HTS current sensor were fabricated by dip-coating a thin Bi 2 -Sr 2 -Ca 2 -Cu 3 -O x (Bi-2223) layer on 99.9% MgO ceramic substrates. The HTS technology enables us to develop a system equipped with a downsized and highly sensitive current monitor. Recently, a prototype system was completed and installed in the beam transport line of the RIKEN Ring Cyclotron to measure the DC-current of high-energy heavy-ion beams. As a result, we succeeded in measuring the intensity of the 600 nA 40 Ar 17+ beam (95 MeV/u). We describe the present status of the monitor system and the results of the beam measurements. (author)

  12. Performance Test of the Next Generation X-Ray Beam Position Monitor System for The APS Upgrade

    Energy Technology Data Exchange (ETDEWEB)

    Yang, B.; Lee, S.; Westferro, F.; Jaski, Y.; Lenkszus, F.; Sereno, N.; Ramanathan, M.

    2017-03-25

    The Advanced Photon Source is developing its next major upgrade (APS-U) based on the multi-bend achromat lattice. Improved beam stability is critical for the upgrade and will require keeping short-time beam angle change below 0.25 µrad and long-term angle drift below 0.6 µrad. A reliable white x-ray beam diagnostic system in the front end will be a key part of the planned beam stabilization system. This system includes an x-ray beam position monitor (XBPM) based on x-ray fluorescence (XRF) from two specially designed GlidCop A-15 absorbers, a second XBPM using XRF photons from the Exit Mask, and two white beam intensity monitors using XRF from the photon shutter and Compton-scattered photons from the front end beryllium window or a retractable diamond film in windowless front ends. We present orbit stability data for the first XBPM used in the feedback control during user operations, as well as test data from the second XBPM and the intensity monitors. They demonstrate that the XBPM system meets APS-U beam stability requirements.

  13. Effects of natural disaster trends: a case study for expanding the pre-positioning network of CARE International.

    Science.gov (United States)

    Bozkurt, Melda; Duran, Serhan

    2012-08-01

    The increasing number of natural disasters in the last decade necessitates the increase in capacity and agility while delivering humanitarian relief. A common logistics strategy used by humanitarian organizations to respond this need is the establishment of pre-positioning warehouse networks. In the pre-positioning strategy, critical relief inventories are located near the regions at which they will be needed in advance of the onset of the disaster. Therefore, pre-positioning reduces the response time by totally or partially eliminating the procurement phase and increasing the availability of relief items just after the disaster strikes. Once the pre-positioning warehouse locations are decided and warehouses on those locations become operational, they will be in use for a long time. Therefore, the chosen locations should be robust enough to enable extensions, and to cope with changing trends in disaster types, locations and magnitudes. In this study, we analyze the effects of natural disaster trends on the expansion plan of pre-positioning warehouse network implemented by CARE International. We utilize a facility location model to identify the additional warehouse location(s) for relief items to be stored as an extension of the current warehouse network operated by CARE International, considering changing natural disaster trends observed over the past three decades.

  14. International Pellet Watch: global monitoring of persistent organic pollutants (POPs) in coastal waters. 1. Initial phase data on PCBs, DDTs, and HCHs.

    Science.gov (United States)

    Ogata, Yuko; Takada, Hideshige; Mizukawa, Kaoruko; Hirai, Hisashi; Iwasa, Satoru; Endo, Satoshi; Mato, Yukie; Saha, Mahua; Okuda, Keiji; Nakashima, Arisa; Murakami, Michio; Zurcher, Nico; Booyatumanondo, Ruchaya; Zakaria, Mohamad Pauzi; Dung, Le Quang; Gordon, Miriam; Miguez, Carlos; Suzuki, Satoru; Moore, Charles; Karapanagioti, Hrissi K; Weerts, Steven; McClurg, Tim; Burres, Erick; Smith, Wally; Van Velkenburg, Michael; Lang, Judith Selby; Lang, Richard C; Laursen, Duane; Danner, Brenda; Stewardson, Nickol; Thompson, Richard C

    2009-10-01

    Samples of polyethylene pellets were collected at 30 beaches from 17 countries and analyzed for organochlorine compounds. PCB concentrations in the pellets were highest on US coasts, followed by western Europe and Japan, and were lower in tropical Asia, southern Africa and Australia. This spatial pattern reflected regional differences in the usage of PCBs and was positively correlated with data from Mussel Watch, another monitoring approach. DDTs showed high concentrations on the US west coast and in Vietnam. In Vietnam, DDT was predominant over its metabolites (DDE and DDD), suggesting the principal source may be current usage of the pesticide for malaria control. High concentrations of pesticide HCHs were detected in the pellets from southern Africa, suggesting current usage of the pesticides in southern Africa. This study demonstrates the utility and feasibility of the International Pellet Watch approach to monitor POPs at a global scale.

  15. Limb defects associated with major congenital anomalies : Clinical and epidemiological study from the international clearinghouse for birth defects monitoring systems

    NARCIS (Netherlands)

    Rosano, A; Botto, LD; Olney, RS; Khoury, MJ; Ritvanen, A; Goujard, J; Stoll, C; Cocchi, G; Merlob, P; Mutchinick, O; Cornel, MC; Castilla, EE; Martinez-Frias, ML; Zampino, G; Erickson, JD; Mastroiacovo, P

    2000-01-01

    Although limb defects associated with other congenital anomalies are rarely studied, they may provide insights into limb development that may be useful for etiologic studies and public health monitoring, me pooled data from II birth defect registries that are part of the International Clearinghouse

  16. SU-F-J-25: Position Monitoring for Intracranial SRS Using BrainLAB ExacTrac Snap Verification

    Energy Technology Data Exchange (ETDEWEB)

    Jang, S; McCaw, T; Huq, M [University of Pittsburgh Cancer Institute, Pittsburgh, PA (United States)

    2016-06-15

    Purpose: To determine the accuracy of position monitoring with BrainLAB ExacTrac snap verification following couch rotations during intracranial SRS. Methods: A CT scan of an anthropomorphic head phantom was acquired using 1.25mm slices. The isocenter was positioned near the centroid of the frontal lobe. The head phantom was initially aligned on the treatment couch using cone-beam CT, then repositioned using ExacTrac x-ray verification with residual errors less than 0.2mm and 0.2°. Snap verification was performed over the full range of couch angles in 15° increments with known positioning offsets of 0–3mm applied to the phantom along each axis. At each couch angle, the smallest tolerance was determined for which no positioning deviation was detected. Results: For couch angles 30°–60° from the center position, where the longitudinal axis of the phantom is approximately aligned with the beam axis of one x-ray tube, snap verification consistently detected positioning errors exceeding the maximum 8mm tolerance. Defining localization error as the difference between the known offset and the minimum tolerance for which no deviation was detected, the RMS error is mostly less than 1mm outside of couch angles 30°–60° from the central couch position. Given separate measurements of patient position from the two imagers, whether to proceed with treatment can be determined by the criterion of a reading within tolerance from just one (OR criterion) or both (AND criterion) imagers. Using a positioning tolerance of 1.5mm, snap verification has sensitivity and specificity of 94% and 75%, respectively, with the AND criterion, and 67% and 93%, respectively, with the OR criterion. If readings exceeding maximum tolerance are excluded, the sensitivity and specificity are 88% and 86%, respectively, with the AND criterion. Conclusion: With a positioning tolerance of 1.5mm, ExacTrac snap verification can be used during intracranial SRS with sensitivity and specificity between 85

  17. Evaluation of the Air Quality Monitor's Performance on the International Space Station

    Science.gov (United States)

    Limero, Thomas; Reese, Eric; Ballard, Ken; Durham, Tamara

    2010-01-01

    The Air Quality Monitor (AQM) was flown to the International Space Station (ISS) as an experiment to evaluate its potential to replace the aging Volatile Organic Analyzer (VOA), which ceased operations in August 2009. The AQM (Figure 1) is a small gas chromatography/differential mobility spectrometer (GC/DMS) manufactured by Sionex. Data was presented at last year s ISIMS conference that detailed the preparation of the AQM for flight, including instrument calibration. Furthermore, initial AQM data was compared to VOA results from simultaneous runs of the two instruments. Although comparison with VOA data provided a measure of confidence in the AQM performance, it is the comparison with results from simultaneously acquired air samples (grab sample containers-GSCs) that will define the success (or failure) of the AQM performance. This paper will update the progress in the AQM investigation by comparing AQM data to results from the analyses of GSC samples, returned from ISS. Additionally, a couple of example will illustrate the AQM s ability to detect disruptions in the spacecraft s air quality. Discussion will also focus upon a few unexpected issues that have arisen and how these will be a addressed in the final operational unit now being built.

  18. Assessment and monitoring of air pollution effects. Possibilities and constraints of international cooperation

    International Nuclear Information System (INIS)

    Panzer, K.F.; Hassan, I.A.; Vellisariou, D.A.

    1996-01-01

    Under the geneva convention on long-range transboundary air pollution, an international cooperative programme on 'Assessment and monitoring of Air effects' had been set-up in 1985. of the 34 signatory states of the convention, 28 participate in the implementation of the programme. The objective is to assess effects of air pollution on forests in europe, using a common survey method in order to assure comparability of survey results. In 1987, 20 countries conducted harmonized forest health surveys based on the assessment of two visible symptoms, loss and/or discoloration of foliage. harmonization of the surveys was quickly achieved because of the simplicity of the methodical approach. The price of rapidly obtaining large-area information on defoliation of forests is, that no distinction can be made in the assessment process between defoliation caused by air pollution and defoliation caused by natural, biotic or a biotic causes. Further improvements of the interpretability of survey results can be expected if additional visible symptoms can be defined for the major species in the different european regions. Possibilities and constraints of incorporating differentiating symptoms into the annual health surveys are discussed. 1 fig., 2 tabs

  19. Analyser position for end-tidal carbon dioxide monitoring in a rebreather circuit.

    Science.gov (United States)

    Ineson, Alastair; Henderson, Kaylene; Teubner, David; Mitchell, Simon

    2010-12-01

    A diving rebreather currently nearing release incorporates an infra-red CO2 analyser at the end of the exhale hose and uses the expired gas CO2 measurement made at this position to detect hypercapnia. This configuration may allow exhaled anatomic and mouthpiece dead space gas to mix with alveolar gas in the exhale hose thus falsely lowering the CO2 measurement, especially at low tidal volumes. A test circuit was constructed using a typical rebreather mouthpiece and exhale hose connected into an anaesthetic machine breathing loop. True end-tidal PCO2 was measured in gas sampled from the mouth and compared breath-by-breath to the PCO2 measured in gas sampled at the end of the exhale hose. Two subjects each completed 60 breaths at tidal volumes of 500, 750, 1000, 1500 and 2000 ml. There was a small (≤ 0.21 kPa) mean difference between true end-tidal CO2 and end-of-hose CO2 at tidal volumes of 1000 ml or more. However, at lower tidal volumes, the mean difference increased and, at 500 ml, it was 1.04 kPa and 0.70 kPa in subjects 1 and 2 respectively. Measurement of the peak exhaled PCO2 at the end of a rebreather exhale hose may provide a reasonable estimation of the true end-tidal CO2 at large tidal volumes, but may significantly underestimate the true end-tidal CO2 at low tidal volumes.

  20. A compact and portable X-ray beam position monitor using Medipix3

    Science.gov (United States)

    Rico-Alvarez, O.; Kachatkou, A.; Marchal, J.; Willis, B.; Sawhney, K.; Tartoni, N.; van Silfhout, R. G.

    2014-12-01

    The present work reports on the design and implementation of a novel portable X-ray beam diagnostics (XBPM) device. The device is transparent to the X-ray beam and provides real-time measurements of beam position, intensity, and size. The measurement principle is based on a pinhole camera which records scattered radiation from a Kapton foil which is placed in the beam path. The use of hybrid detectors (Medipix3) that feature a virtually noiseless readout system with capability of single photon detection and energy resolving power enables the diagnostics with a better resolution and higher sensitivity compared to the use of traditional indirect X-ray detection schemes. We describe the detailed system design, which consists of a vacuum compatible focal plane sensor array, a sensor conditioning and readout board and a heterogeneous data processing unit, which also acts as a network server that handles network communications with clients. The readout protocol for the Medipix3 sensor is implemented using field programmable gate array (FPGA) logic resulting in a versatile and scalable system that is capable of performing advanced functions such as data compression techniques and feature extraction. For the system performance measurements, we equipped the instrument with a single Medipix3 die, bump bonded to a Si sensor, rather than four for which it was designed. Without data compression, it is capable of acquiring magnified images and profiles of synchrotron X-ray beams at a transfer rate through Ethernet of 27 frames/s for one Medipix3 die.

  1. A new tool to monitor training and performance of sport horses using global positioning system (GPS) with integrated GSM capabilities.

    Science.gov (United States)

    Hebenbrock, M; Düe, M; Holzhausen, H; Sass, A; Stadler, P; Ellendorff, F

    2005-07-01

    Global Positioning Systems (GPS) are considered suitable to monitor the position and velocity of horses during cross-country competition or in training. Furthermore, simultaneous recording of life data such as heart rate could be useful to assess the horse's condition during exercise. To test the suitability and reliability of a commercially available GPS system with integrated heart rate recording system and with built in GSM for data transmission, the Fidelak Equipilot Type EP-2003-15/G-2.11 (EP-15/G) was evaluated first for reliability of pulse recording from a pulse generator within the physiological range of horses; furthermore distance, velocity and heart rate recordings were carried out on a standard 1000 m field track with five repetitions. Agreement (% deviation from actually measured distance and from stopwatch-distance based velocity calculations) and variability (Coefficient of Variation for distance, velocity, heart rate) were calculated. From the results it was safe to assume that the heart rate sensor recorded horse heart rates at a high degree of accuracy. Overall distances and velocities are in high agreement with actually measured values. However, overall variability expressed in terms of relative variability (C.V.) is smaller for distance recording (C.V. 0.68%) when compared to velocity (C.V. 1.01%). The system tested is suitable and reliable for simultaneously recording of distance, velocity and heart rates for horses during cross country exercise. GPS-based monitoring of movement along with simultaneous recording of physiological data and the possibility to call upon data will not only be of benefit for training horses or for surveillance during competition, it may also be suitable for distant patient monitoring and in behavioural studies as well as in veterinary medicine in general.

  2. Position of Serbia on the international market of milk, dairy products, eggs and wool

    OpenAIRE

    Đorović Milutin; Stevanović Simo; Lazić Verica

    2011-01-01

    This paper presents a comparative analysis of the major indicators of both world and domestic markets of milk, dairy products, eggs and wool. Namely, for the past 20 years, for the observed subperiods, the method of comparative analysis was used to study quantitative and structural differences in the production and trade of analyzed product groups, at both the world and at the level of continents and some countries. The leading manufacturers and flows of international trade and the leading ex...

  3. Selective internalization of self-assembled artificial oil bodies by HER2/neu-positive cells

    International Nuclear Information System (INIS)

    Chiang, Chung-Jen; Lin, Che-Chin; Lin, Li-Jen; Chang, Chih-Hsiang; Chao, Yun-Peng

    2011-01-01

    A novel delivery carrier was developed using artificial oil bodies (AOBs). Plant seed oil bodies (OBs) consist of a triacylglycerol matrix surrounded by a monolayer of phospholipids embedded with the storage protein oleosin (Ole). Ole consists of a central hydrophobic domain with two amphiphatic arms that extrude from the surface of OBs. In this study, a bivalent anti-HER2/neu affibody domain (ZH2) was fused with Ole at the C terminus. After overproduction in Escherichia coli, the fusion protein (Ole-ZH2) was recovered to assemble AOBs. The size of self-assembled AOBs was tailored by varying the oil/Ole-ZH2 ratio and pH to reach a nanoscale. Upon co-incubation with tumor cells, the nanoscale AOBs encapsulated with a hydrophobic fluorescence dye were selectively internalized by HER2/neu-overexpressing cells and displayed biocompatibility with the cells. In addition, the ZH2-mediated endosomal entry of AOBs occurred in a time- and AOB dose-dependent manner. The internalization efficiency was as high as 90%. The internalized AOBs disintegrated at the non-permissive pH (e.g. in acidic endosomes) and the cargo dye was released. Results of in vitro study revealed a sustained and prolonged release profile. Taken together, our findings indicate the potential of AOBs as a delivery carrier.

  4. Selective internalization of self-assembled artificial oil bodies by HER2/neu-positive cells

    Energy Technology Data Exchange (ETDEWEB)

    Chiang, Chung-Jen; Lin, Che-Chin [Department of Medical Laboratory Science and Biotechnology, China Medical University, Taichung, Taiwan (China); Lin, Li-Jen [School of Chinese Medicine, China Medical University, Taichung, Taiwan (China); Chang, Chih-Hsiang; Chao, Yun-Peng, E-mail: cjchiang@mail.cmu.edu.tw, E-mail: ypchao@fcu.edu.tw [Department of Chemical Engineering, Feng Chia University, Taichung, Taiwan (China)

    2011-01-07

    A novel delivery carrier was developed using artificial oil bodies (AOBs). Plant seed oil bodies (OBs) consist of a triacylglycerol matrix surrounded by a monolayer of phospholipids embedded with the storage protein oleosin (Ole). Ole consists of a central hydrophobic domain with two amphiphatic arms that extrude from the surface of OBs. In this study, a bivalent anti-HER2/neu affibody domain (ZH2) was fused with Ole at the C terminus. After overproduction in Escherichia coli, the fusion protein (Ole-ZH2) was recovered to assemble AOBs. The size of self-assembled AOBs was tailored by varying the oil/Ole-ZH2 ratio and pH to reach a nanoscale. Upon co-incubation with tumor cells, the nanoscale AOBs encapsulated with a hydrophobic fluorescence dye were selectively internalized by HER2/neu-overexpressing cells and displayed biocompatibility with the cells. In addition, the ZH2-mediated endosomal entry of AOBs occurred in a time- and AOB dose-dependent manner. The internalization efficiency was as high as 90%. The internalized AOBs disintegrated at the non-permissive pH (e.g. in acidic endosomes) and the cargo dye was released. Results of in vitro study revealed a sustained and prolonged release profile. Taken together, our findings indicate the potential of AOBs as a delivery carrier.

  5. International positioning of South African electricity prices and commodity differentiated pricing

    Directory of Open Access Journals (Sweden)

    George A. Thopila

    2013-07-01

    Full Text Available The South African electricity industry has seen a dramatic increase in prices over the past 3 years. This increase has been blanketed across all sectors and is based on a number of factors such as sector, usage and, in the case of domestic pricing, suburb. The cost of electricity in South Africa, particularly to the industrial sector, has been among the lowest in the world. In this paper, we analyse the recent price increases in the South African electricity sector and discuss the price determination mechanism employed by Eskom, South Africa's electricity provider. We also analyse the revenue and sales of Eskom and review the electricity price from an international perspective. The concept of differential pricing and international benchmarking is analysed as a possibility for the South African industrial electricity industry, so that all sectors are not adversely affected by across-the-board increases. Our aim is to raise the question of whether South Africa's electricity prices are in line with international increases and to suggest the possibility of differentiated prices in the local electricity sector.

  6. Competitive strategies and strategic positioning of oil companies in the international oil business: theory and practice in perspective

    International Nuclear Information System (INIS)

    Dos Santos, E.M.; Teixeira Carneiro, J.M.; Ferreira Deschamps Cvalcanti, M.A.

    1999-01-01

    This is the first work of a series of four articles aiming to analyse the concepts of competitive strategy and strategic positioning of firms in the international oil industry. The authors present the essence of their analytical model, which are based on the theoretical framework of competitive strategy developed by Michael Porter, from the University of Harvard. The second article is published hereunder, the third and fourth ones will appear in the next issue. (authors)

  7. Impact of experimentally induced positive and anxious mood on alcohol expectancy strength in internally motivated drinkers.

    Science.gov (United States)

    Grant, Valerie V; Stewart, Sherry H

    2007-01-01

    The effects of musically-induced positive and anxious mood on explicit alcohol-related cognitions (alcohol expectancy strength) in 47 undergraduate students who consume alcohol either to enhance positive mood states (for enhancement motives) or to cope with anxiety (for anxiety-related coping motives) were investigated. Pre- and post-mood induction, participants completed the emotional reward and emotional relief subscales of the Alcohol Craving Questionnaire - Now. The hypothesis that anxiety-related coping motivated drinkers in the anxious mood condition (but not those in the positive mood condition) would exhibit increases in strength of explicit emotional relief alcohol expectancies after the mood induction was supported. An additional, unanticipated finding was that enhancement-motivated drinkers in the anxious condition also showed significant increases in strength of explicit emotional relief (but not emotional reward) alcohol expectancies. The hypothesis that enhancement-motivated (but not anxiety-related coping motivated) participants would exhibit increases in explicit emotional reward expectancies following exposure to the positive mood induction procedure was not supported. Taken together with past research findings, the current results highlight the importance of distinguishing between subtypes of negative affect (i.e., anxious and depressed affect) in exploring the affective antecedents of explicit alcohol outcome expectancies.

  8. The primary care physician and Alzheimer's disease: an international position paper.

    NARCIS (Netherlands)

    Villars, H.; Oustric, S.; Andrieu, S.; Baeyens, J.P.; Bernabei, R.; Brodaty, H.; Brummel-Smith, K.; Celafu, C.; Chappell, N.; Fitten, J.; Frisoni, G.; Froelich, L.; Guerin, O.; Gold, G.; Holmerova, I.; Iliffe, S.; Lukas, A.; Melis, R.J.F.; Morley, J.E.; Nies, H.; Nourhashemi, F.; Petermans, J.; Ribera Casado, J.; Rubenstein, L.; Salva, A.; Sieber, C.; Sinclair, A.; Schindler, R.; Stephan, E.; Wong, R.Y.; Vellas, B.

    2010-01-01

    This paper aims to define the role of the primary care physician (PCP) in the management of Alzheimer's disease (AD) and to propose a model for a work plan. The proposals in this position paper stem from a collaborative work of experts involved in the care of AD patients. It combines evidence from a

  9. 10 CFR 20.1502 - Conditions requiring individual monitoring of external and internal occupational dose.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 1 2010-01-01 2010-01-01 false Conditions requiring individual monitoring of external and... PROTECTION AGAINST RADIATION Surveys and Monitoring § 20.1502 Conditions requiring individual monitoring of..., columns 1 and 2, of appendix B to §§ 20.1001-20.2402; (2) Minors likely to receive, in 1 year, a committed...

  10. Design of a Standing-Wave Multi-Cavity Beam-Monitor for Simultaneous Beam Position and Emittance Measurements

    Science.gov (United States)

    Kim, Jin-Soo; Miller, Roger; Nantista, Christopher

    2004-12-01

    A high precision emittance measurement requires precise beam position at the measurement location. At present there is no existing technique, commercial or otherwise, for non-destructive pulse-to-pulse simultaneous beam position and emittance measurement. FAR-TECH, Inc. is currently developing a high precision cavity-based beam monitor for simultaneous beam position and emittance measurements pulse-to-pulse, without beam interception and without moving parts. The design and anlysis of a multi-cavity standing wave structure for a pulse-to-pulse emittance measurement system in which the quadrupole and the dipole standing wave modes resonate at harmonics of the beam operating frequency is presented. Considering the Next Linear Collider beams, an optimized 9-cavity standing wave system is designed for simultaneous high precision beam position and emittance measurements. It operates with the π - quadrupole mode resonating at 16th harmonic of the NLC bunch frequency, and the 3 π /4 dipole mode at 12th harmonic (8.568 GHz). The 9-cavity system design indicates that the two dipoles resonate almost at the same frequency 8.583 GHz and the quadrupole at 11.427 GHz according to the scattering parameter calculations. The design can be trivially scaled so that the dipole frequency is at 8.568 GHz, and the quadrupole frequency can then be tuned during fabrication to achieve the desired 11.424 GHz. The output powers from these modes are estimated for the NLC beams. An estimated rms-beam size resolution is sub micro-meters and beam positions in sub nano-meters.

  11. INAA analysis of rocks: A routine method using Fe as an internal flux monitor

    International Nuclear Information System (INIS)

    Kay, R.W.; Kay, S. Mahlburg

    1992-01-01

    Over the past decade at Cornell, trace elements in over 2500 rocks have been analyzed by INAA. The samples, mainly volcanic rocks, have known concentrations of major elements (e.g. Si, Ti, Al, Mg, Ca, K, Fe, Na) and the last two of these (Fe and Na) are also determined by activation, using rock standards (e.g. USGS standards BCRl, BHVO, etc.). Differences between Fe determined by INAA and that determined as a part of the major element analysis are mainly attributed to volatile (H 2 O, CO 2 ) loss (especially when major element analyses were done by electron microprobe on fused powders, whereas the INAA analyses were done on the powders), and to flux variability during irradiation. Instead of reporting two values for Fe we use Fe as an internal flux monitor, with Na and the trace elements being reported relative to the given Fe value. The ratio Na/Fe is used as a sensitive check on the identity of the sample and as a monitor of alkali loss affecting the major element analysis. Other than this modification (Kay et aL 1987, also reported in Chappell and Hergt, 1989) we use an INAA method similar to mat practiced by many labs. Powdered samples (about 0.5 g) are sealed in high-purity silica tubes and irradiated in the Cornell Triga reactor. Samples are counted for a minimum of 2 hours (up to 10 hours) 7 and 40 days after irradiation. Data are reduced using a program written at Cornell, with peak and background regions that have been checked for interferences. Corrections are routinely applied for Ce (Fe), Nd (Br), Tb (Th), Eu (Ba), Lu (U), and Yb (Th) (interference is from element in parentheses). A U fission yield correction is applied to La, Ce, Nd, and Ba. A correction for Ta introduced by grinding in WC containers can be made using known Ta/W ratios in the grinding containers. The correction amounted to 10-20% of the Ta gross peak. Recently, samples have been prepared in a ceramic grinding containers; for these, no Ta correction is needed. Trace elements determined

  12. The long term storage of radioactive waste: Safety and sustainability. A position paper of international experts

    International Nuclear Information System (INIS)

    2003-06-01

    The purpose of the report is to reflect the currently prevailing views among experts in the field of radioactive waste storage and disposal. It is intended for use as a central and authoritative reference point for national discussions and policy papers. It is therefore potentially useful to national committees and bodies concerned with the management of radioactive waste. It may also be of value to concerned members of the public since it is written in language that should be comprehensible to the informed lay person. It was produced as a result of several meetings of experts in the first part of 2002. Since then, it has been reviewed by the international Waste Safety Standards Committee (WASSC), by the WASSC Subgroup on Principles and Criteria for the Disposal of Radioactive Waste at its meeting in October 2000 and by a technical committee convened specifically to review the paper at a meeting held in November 2002. Finally, the essential conclusions of the paper were presented to and discussed with participants to the International Conference on Issues and Trends in Radioactive Waste Management, held in Vienna in December 2002

  13. Status of higher order mode beam position monitors in 3.9 GHz superconducting accelerating cavities at FLASH

    CERN Document Server

    Zhang, P; Jones, R M; Flisgen, T; Van Rienen, U; Shinton, I R R

    2013-01-01

    Higher order mode (HOM) beam position monitors (BPM) are being developed for the 3.9 GHz third harmonic superconducting accelerating cavities at FLASH. The transverse beam position in a cavity can be determined utilizing beam-excited HOMs based on dipole components. The existing couplers used for HOM suppression provide necessary signals. The diagnostics principle is similar to a cavity BPM, but requires no additional vacuum instruments on the linac. The challenges of HOM-BPM for 3.9 GHz cavities lie in the dense HOM spectrum arising from the coupling of the majority HOMs amongst the four cavities in the cryo-module ACC39. HOMs with particularly promising diagnostics features were evaluated using a spectrum analyzer and custom-built test electronics with various data analysis techniques, data reduction was focused on. After careful theoretical and experimental assessment of the HOM spectrum, multi-cavity modes in the region of 5 GHz were chosen to provide a global position over the complete module with superi...

  14. Internal Hydrolysis Indicator for Sample Specific Monitoring of β-Glucuronidase Activity.

    Science.gov (United States)

    Taylor, Lacy L; Flint, Noah A; Ma, Vinh; Hill, Brandy M; Clark, Chantry J; Strathmann, Frederick G

    2017-06-01

    Metabolized forms of benzodiazepines (benzos) can cause issues with mass spectrometry identification. Benzodiazepines undergo a process called glucuronidation during metabolism that attaches a glucuronic acid for increased solubility. Often in clinical testing an enzymatic hydrolysis step is implemented to increase the sensitivity of benzodiazepines by hydrolyzing β-D-glucuronic acid from benzodiazepine-glucuronide conjugates in urine samples using the β-Glucuronidase enzyme. In this study resorufin β-D-glucuronide, a substrate of the β-Glucuronidase enzyme, was added to patient samples to determine if proper hydrolysis had occurred. The presence of resorufin as an Internal Hydrolysis Indicator (IHI) shows the activity and efficiency of the enzyme in each patient sample. Synthetic/patient urine samples were obtained and mixed with hydrolysis buffer containing resorufin β-D-glucuronide. The β-Glucuronidase enzyme was used to hydrolyze the benzodiazepine analytes as well as resorufin β-D-glucuronide. The enzymatic hydrolysis addition increased the positivity rate of benzodiazepines by 42.5%. The β-Glucuronidase substrate resorufin (IHI) displayed variability in area counts between patient samples. Comparative studies with internal standards and resorufin (IHI) showed no correlation between recovery and analyte variability. Hydrolysis reactions greatly improved the sensitivity of benzodiazepines by liquid chromatography time-of-flight mass spectrometry analysis. The large variation in resorufin (IHI) area counts amongst patient samples indicates possible variability in enzymatic hydrolysis activity. The enzymatic hydrolysis step is a part of the extraction procedure and should be controlled for in each patient sample. © The Author 2017. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  15. Internal Dosimetry Monitoring- Detection Limits for a Selected Set of Radionuclides and Their Translation Into Committed Effective Dose

    International Nuclear Information System (INIS)

    Brandl, A.; Hrnecek, E.; Steger, F.

    2004-01-01

    To harmonize the practice of internal dosimetry monitoring across the country, the Austrian Standards Institute is currently drafting a new set of standards which are concerned with occupational incorporation monitoring of individuals handling non-sealed radioactive material. This set of standards is expected to consist of three parts discussing the general necessity and frequency, the requirements for monitoring institutions, and the determination and rigorous calculation of committed effective dose after incorporation of radioactive material, respectively. Considerations of the requirements for routine monitoring laboratories have led to an evaluation of the detection limits for routine monitoring equipment. For a selected set of radionuclides, these detection limits are investigated in detail. The main emphasis is placed on the decay chains of naturally occurring radionuclides showing some significant potential for being out of equilibrium due to chemical processes in certain mining industries. The radionuclides considered in this paper are 226Ra, 228Ra, 228Th, 232Th, 234U, 235U, and 238U. Given the routine monitoring intervals of the Austrian Standard, these detection limits are translated into information on committed effective dose. This paper investigates whether routine monitoring equipment is sufficient to ensure compliance with EC directive 96/29/Euratom for this selected set of radionuclides. (Author) 9 refs

  16. Evaluation of a technique for in vivo internal monitoring of 18F within a Brazilian Laboratory Network

    International Nuclear Information System (INIS)

    Oliveira, C. M.; Lima, F. F.; De Oliveira, M. L.; Da Silva, T. V.; Dantas, A. L.; Dantas, B. M.; Alonso, T. C.; Da Silva, A. G.

    2013-01-01

    18 FDG, an analogue of glucose labelled with the radionuclide 18 F, is the most widely used radiopharmaceutical in positron emission tomography/computed tomography technique. In Brazil, there are currently eight 18 FDG plants in operation and other facilities are expected to start their production in the near future. The growth in the production and clinical use of 18 FDG represents an increasing risk of worker exposures. According to national regulations and international recommendations, internal exposures should be effectively controlled in order to keep doses as low as possible. The implementation of a routine monitoring programme towards the estimation of internal doses related to the incorporation of 18 F is difficult, mainly due to its short physical half-life, the cost of a bioassay laboratory and the need of a monitoring service promptly available near the production plant. This paper describes the implementation and evaluation of a methodology for in vivo brain monitoring of 18 F to be applied in cases of suspected incorporation of 18 FDG. The technique presented a minimum detectable effective dose in the order of nano-Sieverts, which allows its application for occupational monitoring purposes. (authors)

  17. Positioning of sodium-glucose cotransporter-2 inhibitors in national and international guidelines.

    Science.gov (United States)

    Morillas, Carlos

    2016-11-01

    Sodium-glucose cotransporter-2 inhibitors (SGLT2-i) selectively and reversibly inhibit sodium-glucose cotransporter-2 (SGLT2), promoting renal glucose excretion and reducing plasma glycaemia. By increasing renal glucose excretion, these drugs favour a negative energy balance, leading to weight loss. Their glucoselowering effect is independent of insulin. Although these drugs have only recently been developed, they have been included in all the main national and international guidelines since 2014. The present review summarises the most important recommendations on the use of SGLT2 in patients with DM2 contained in the most recently published guidelines and consensus statements. Copyright © 2016 Elsevier España, S.L.U. All rights reserved.

  18. SLICEIT and TAHMO Partnerships: Students Local and International Collaboration for Climate and Environmental Monitoring, Technology Development, Education, Adaptation and Mitigation

    Science.gov (United States)

    Aishlin, P. S.; Selker, J. S.

    2015-12-01

    Climate change understanding and impacts vary by community, yet the global nature of climate change requires international collaboration to address education, monitoring, adaptation and mitigation needs. We propose that effective climate change monitoring and education can be accomplished via student-led local and international community partnerships. By empowering students as community leaders in climate-environmental monitoring and education, as well as exploration of adaptation/mitigation needs, well-informed communities and young leadership are developed to support climate change science moving forward. Piloted 2013-2015, the SLICEIT1 program partnered with TAHMO2 to connect student leaders in North America, Europe and Africa. At the international level, schools in the U.S.A and Netherlands were partnered with schools in Ghana, Kenya, and Uganda for science and cultural exchange. Each school was equipped with a climate or other environmental sensing system, real-time data publication and curricula for both formal and informal science, technology, engineering and math education and skill development. African counterparts in TAHMO's School-2-School program collect critically important data for enhanced on-the-ground monitoring of weather conditions in data-scarce regions of Africa. In Idaho, student designed, constructed and installed weather stations provide real time data for classroom and community use. Student-designed formal educational activities are disseminated to project partners, increasing hands-on technology education and peer-based learning. At the local level, schools are partnered with a local agency, research institute, nonprofit organization, industry and/or community partner that supplies a climate science expert mentor to SLICEIT program leaders and teachers. Mentor engagement is facilitated and secured by program components that directly benefit the mentor's organization and local community via climate/environment monitoring, student workforce

  19. Response of monitors of surface contamination to internal exposition control from 131I in the 'nuclear medicine services'

    International Nuclear Information System (INIS)

    Puerta, Nancy; Rojo, Ana M.; Villella, Adrian; Gossio, Sebastian; Parada, Ines Gomez; Acosta, Norma; Arenas, German

    2013-01-01

    The IAEA, in its publication RS-G-1.2, proposes individual control of workers occupationally exposed with risk of internal exposure when the potential exposure provided by incorporation leads to a value of annual committed effective dose equal to or greater than 1 mSv. Because the radionuclide 131 I is the most important to control internal exposure in Nuclear Medicine Services, it is evaluated if the surface contamination monitors, commonly used in nuclear medicine centers of Argentina, would implement individual control of internal exposure to 131 I. Selected detectors were calibrated with a dummy neck and thyroid with calibrated sources of 131 I and 133 Ba reference. For each detector is was estimated the detection efficiency for 131 I and its detection limit. Each instrument was evaluated for the lowest effective dose possible to detect compromised by individual routine monitoring with different measurement intervals . We analyzed the response of each team for determining conditions that may be effective for the control of internal exposure of 131 I. Finally , we conclude that the daily individual monitoring surface contamination detectors available in the Nuclear Medicine Services is feasible to implement and ensures detection of significant additions of 131 I

  20. ITRAP - International laboratory and field test site exercise for radiation detection instruments and monitoring systems at border crossings

    International Nuclear Information System (INIS)

    Beck, P.; Schmitzer, C.; Duftschmid, K.E.; Arlt, R.

    2001-01-01

    Illicit trafficking in nuclear materials has become more and more a problem, due to the circulation of a high number of radioactive sources and the big amount of nuclear material. The IAEA database counts at present more than 300 verified cases. The endangering cased thereby ranges from possible health defect for the publication to terrorists activities and production of nuclear weapons. In addition to the primary criminal reasons the illegal disposal of radioactive sources as salvage, scrap and others show a further problem, which has lead to severe accidents and lethal effects in the past (e.g. Goiana, Mexico). Some countries have already under taken countermeasures (e.g. Monitoring at the Finnish-Russian and German- Polish border, border monitoring in Italy). The International Atomic Energy Agency (IAEA) has reacted on this actual problem by setting up a new program to fight against nuclear criminality and has suggested a pilot study for the practical test of border monitoring systems. Co-ordinated by the Federal Ministry of Economy and Labour the Austrian Government financed the pilot study ITRAP (Illicit Trafficking Radiation Detection Assessment Program) carried out by the Austrian Research Centers Seibersdorf (ARCS). Aim of the study was to work out the technical requirements and the practicability of an useful monitoring system at border crossings. The results of the study will be offered by the IAEA to the member states as international recommendations for border monitoring systems

  1. INFORMAS (International Network for Food and Obesity/non-communicable diseases Research, Monitoring and Action Support): summary and future directions.

    Science.gov (United States)

    Kumanyika, S

    2013-10-01

    This supplement presents the foundational elements for INFORMAS (International Network for Food and Obesity/non-communicable diseases Research, Monitoring and Action Support). As explained in the overview article by Swinburn and colleagues, INFORMAS has a compelling rationale and has set forth clear objectives, outcomes, principles and frameworks for monitoring and benchmarking key aspects of food environments and the policies and actions that influence the healthiness of food environments. This summary highlights the proposed monitoring approaches for the 10 interrelated INFORMAS modules: public and private sector policies and actions; key aspects of food environments (food composition, labelling, promotion, provision, retail, prices, and trade and investment) and population outcomes (diet quality). This ambitious effort should be feasible when approached in a step-wise manner, taking into account existing monitoring efforts, data sources, country contexts and capacity, and when adequately resourced. After protocol development and pilot testing of the modules, INFORMAS aims to be a sustainable, low-cost monitoring framework. Future directions relate to institutionalization, implementation and, ultimately, to leveraging INFORMAS data in ways that will bring key drivers of food environments into alignment with public health goals. © 2013 The Authors. Obesity Reviews published by John Wiley & Sons Ltd on behalf of the International Association for the Study of Obesity.

  2. Novel, continuous monitoring of fine‐scale movement using fixed‐position radiotelemetry arrays and random forest location fingerprinting

    Science.gov (United States)

    Harbicht, Andrew B.; Castro-Santos, Theodore R.; Ardren, William R.; Gorsky, Dimitry; Fraser, Dylan

    2017-01-01

    Radio‐tag signals from fixed‐position antennas are most often used to indicate presence or absence of individuals, or to estimate individual activity levels from signal strength variation within an antenna's detection zone. The potential of such systems to provide more precise information on tag location and movement has not been explored in great detail in an ecological setting.By reversing the roles that transmitters and receivers play in localization methods common to the telecommunications industry, we present a new telemetric tool for accurately estimating the location of tagged individuals from received signal strength values. The methods used to characterize the study area in terms of received signal strength are described, as is the random forest model used for localization. The resulting method is then validated using test data before being applied to true data collected from tagged individuals in the study site.Application of the localization method to test data withheld from the learning dataset indicated a low average error over the entire study area (movement data for tagged fish along a single axis (a migratory path) and is particularly useful for monitoring passage along migratory routes. The new methods applied in this study can also be expanded to include multiple axes (x, y, z) and multiple environments (aquatic and terrestrial) for remotely monitoring wildlife movement.

  3. International aspirations for speech-language pathologists' practice with multilingual children with speech sound disorders: development of a position paper.

    Science.gov (United States)

    McLeod, Sharynne; Verdon, Sarah; Bowen, Caroline

    2013-01-01

    A major challenge for the speech-language pathology profession in many cultures is to address the mismatch between the "linguistic homogeneity of the speech-language pathology profession and the linguistic diversity of its clientele" (Caesar & Kohler, 2007, p. 198). This paper outlines the development of the Multilingual Children with Speech Sound Disorders: Position Paper created to guide speech-language pathologists' (SLPs') facilitation of multilingual children's speech. An international expert panel was assembled comprising 57 researchers (SLPs, linguists, phoneticians, and speech scientists) with knowledge about multilingual children's speech, or children with speech sound disorders. Combined, they had worked in 33 countries and used 26 languages in professional practice. Fourteen panel members met for a one-day workshop to identify key points for inclusion in the position paper. Subsequently, 42 additional panel members participated online to contribute to drafts of the position paper. A thematic analysis was undertaken of the major areas of discussion using two data sources: (a) face-to-face workshop transcript (133 pages) and (b) online discussion artifacts (104 pages). Finally, a moderator with international expertise in working with children with speech sound disorders facilitated the incorporation of the panel's recommendations. The following themes were identified: definitions, scope, framework, evidence, challenges, practices, and consideration of a multilingual audience. The resulting position paper contains guidelines for providing services to multilingual children with speech sound disorders (http://www.csu.edu.au/research/multilingual-speech/position-paper). The paper is structured using the International Classification of Functioning, Disability and Health: Children and Youth Version (World Health Organization, 2007) and incorporates recommendations for (a) children and families, (b) SLPs' assessment and intervention, (c) SLPs' professional

  4. The participatory design of a performance oriented monitoring and evaluation system in an international development environment.

    Science.gov (United States)

    Guerra-López, Ingrid; Hicks, Karen

    2015-02-01

    This article illustrates the application of the impact monitoring and evaluation process for the design and development of a performance monitoring and evaluation framework in the context of human and institutional capacity development. This participative process facilitated stakeholder ownership in several areas including the design, development, and use of a new monitoring and evaluation system, as well their targeted results and accomplishments through the use of timely performance data gathered through ongoing monitoring and evaluation. The process produced a performance indicator map, a comprehensive monitoring and evaluation framework, and data collection templates to promote the development, implementation, and sustainability of the monitoring and evaluation system of a farmer's trade union in an African country. Copyright © 2014 Elsevier Ltd. All rights reserved.

  5. An international position paper on mother-infant (perinatal) mental health, with guidelines for clinical practice.

    Science.gov (United States)

    Brockington, Ian; Butterworth, Ruth; Glangeaud-Freudenthal, Nine

    2017-02-01

    The purpose of this paper is to set out informal, provisional and comprehensive but concise guidelines for mother-infant (perinatal) mental health (psychiatry), as an area of specialisation. It is informal in the sense that the authors are clinicians and researchers from many different nations, who share a common goal and vision, speaking on their own behalf and not with the backing of any authority or society. It is provisional in the expectation that it can be improved by criticism and new research findings. It is a comprehensive summary of the development of the specialty, its core knowledge and recommended investigations and interventions. It is concise (under 6,000 words, taking less than an hour to read) in order to increase readership and facilitate translation. No attempt has been made to parade the evidence for these suggestions, because the document would have been too long to translate, and for many to read. Instead, drafts were circulated for criticism by those included in the authorship, resulting in a consensus (finalised by the three principal authors), providing a framework to guide service provision, clinical practice and research. The full list of authors, from 33 nations, is given in the postscript. They include mother-infant (or parent-infant) and perinatal adult or child psychiatrists and those with a special interest; mother-infant, perinatal and forensic psychologists; psychiatric nurses; the founders of Postpartum Support International and the Association for Postnatal Illness; representatives of social work and obstetrics and the management of these services, and research scientists working in the field.

  6. Development of nanometer resolution C-Band radio frequency beam position monitors in the Final Focus Test Beam

    Energy Technology Data Exchange (ETDEWEB)

    Slaton, T.; Mazaheri, G. [Stanford Univ., CA (US). Stanford Linear Accelerator Center; Shintake, T. [National Lab. for High Energy Physics, Tsukuba, Ibaraki (Japan)

    1998-08-01

    Using a 47 GeV electron beam, the Final Focus Test Beam (FFTB) produces vertical spot sizes around 70 nm. These small beam sizes introduce an excellent opportunity to develop and test high resolution Radio Frequency Beam Position Monitors (RF-BPMs). These BPMs are designed to measure pulse to pulse beam motion (jitter) at a theoretical resolution of approximately 1 nm. The beam induces a TM{sub 110} mode with an amplitude linearly proportional to its charge and displacement from the BPM's (cylindrical cavity) axis. The C-band (5,712 MHz) TM{sub 110} signal is processed and converted into beam position for use by the Stanford Linear Collider (SLC) control system. Presented are the experimental procedures, acquisition, and analysis of data demonstrating resolution of jitter near 25 nm. With the design of future e{sup +}e{sup -} linear colliders requiring spot sizes close to 3 nm, understanding and developing RF-BPMs will be essential in resolving and controlling jitter.

  7. The international project of radiation and hydrochemical investigation and monitoring of general Caspian rivers

    International Nuclear Information System (INIS)

    Passell, H.D.; Barber, D.S.; Kadyrzhanov, K.K; Solodukhin, V.P.; Chernykh, E.E.; Arutyunyan, R.V.; Valyaev, A.N.; Kadik, A.A.; Stepanetts, O.V; Vernadsky, V.I.; Alizade, A.A.; Gutiev, I.S.; Mamedov, R.F.; Nadareishvili, K.S.; Chkhartishvili, A.G.; Tsitskishvili, M.S.; Chubaryan, E. V; Gevorgyan, R.G.; Puskyulyan, K.I.

    2005-01-01

    Full text: The scientific community of six countries (USA, Kazakhstan, Russia, Georgia, Armenia, and Azerbaijan) has developed the ecological project 'Joint International Researches and Creation of the General System of Radiation and Hydro-chemical Monitoring of Rivers of the Caspian Sea Basin.' The purpose of this project is to investigate and characterized contamination by radionuclides and toxic and chemically hazardous elements and create a valid system of radiation and hydro-chemical monitoring of the main river basins of the Caspian region: the Volga, Ural, Emba and Kura. The basins of these rivers cover large parts of Europe and Asia, including parts of Russia, West Kazakhstan and the South Caucasus and including territories of Georgia, Armenia and Azerbaijan. The total area of the basins of these rivers exceeds combined area of such large European states as France, Spain and Germany, and comprises 1631 sq. km. All these rivers are the main life-supporting water arteries for the region's inhabitants, a population that comprises tens of millions of people Also, the outlets of these rivers determine the condition of the aquatic environment of the Caspian Sea. The ecological condition of the aquatic environment of all the rivers of the Caspian Sea is to a great extent due to contamination, the main components of which are anthropogenic radioactive elements, heavy metals and oil products. At present, information about contamination levels of these rivers is not known and is occasionally contradictory. In this connection there is an obvious need of qualified investigation of contamination levels and its character in the basins of these rivers and in creating a common monitoring system to assess the quality of the aquatic environment. The present project is devoted to this matter. 1. The project provides for the following main tasks: 1. Wide-ranging investigation of the level and character of contamination by radionuclides and toxic elements of the river basins

  8. International Committee for Monitoring Assisted Reproductive Technologies world report: Assisted Reproductive Technology 2008, 2009 and 2010.

    Science.gov (United States)

    Dyer, S; Chambers, G M; de Mouzon, J; Nygren, K G; Zegers-Hochschild, F; Mansour, R; Ishihara, O; Banker, M; Adamson, G D

    2016-07-01

    What were utilization, outcomes and practices in assisted reproductive technology (ART) globally in 2008, 2009 and 2010? Global utilization and effectiveness remained relatively constant despite marked variations among countries, while the rate of single and frozen embryo transfers (FETs) increased with a concomitant slight reduction in multiple birth rates. ART is widely practised in all regions of the world. Monitoring utilization, an approximation of availability and access, as well as effectiveness and safety is an important component of universal access to reproductive health. This is a retrospective, cross-sectional survey on utilization, effectiveness and safety of ART procedures performed globally from 2008 to 2010. Between 58 and 61 countries submitted data from a total of nearly 2500 ART clinics each year. Aggregate country data were processed and analyzed based on forms and methods developed by the International Committee for Monitoring Assisted Reproductive Technologies (ICMART). Results are presented at country, regional and global level. For the years 2008, 2009 and 2010, >4 461 309 ART cycles were initiated, resulting in an estimated 1 144 858 babies born. The number of aspirations increased by 6.4% between 2008 and 2010, while FET cycles increased by 27.6%. Globally, ART utilization remained relatively constant at 436 cycles/million in 2008 and 474 cycles/million population in 2010, but with a wide country range of 8-4775 cycles/million population. ICSI remained constant at around 66% of non-donor aspiration cycles. The IVF/ICSI combined delivery rate (DR) per fresh aspiration was 19.8% in 2008; 19.7% in 2009 and 20.0% in 2010, with corresponding DRs for FET of 18.8, 19.7 and 20.7%. In fresh non-donor cycles, single embryo transfer increased from 25.7% in 2008 to 30.0% in 2010, while the average number of embryos transferred fell from 2.1 to 1.9, again with wide regional variation. The rates of twin deliveries following fresh non-donor transfers

  9. It gets better: resolution of internalized homophobia over time and associations with positive health outcomes among MSM.

    Science.gov (United States)

    Herrick, Amy L; Stall, Ron; Chmiel, Joan S; Guadamuz, Thomas E; Penniman, Typhanye; Shoptaw, Steven; Ostrow, David; Plankey, Michael W

    2013-05-01

    Health disparities research among gay and bisexual men has focused primarily on risk and deficits. However, a focus on resiliencies within this population may greatly benefit health promotion. We describe a pattern of resilience (internalized homophobia (IHP) resolution) over the life-course and its associations with current health outcomes. 1,541 gay and bisexual men from the Multi-Center AIDS Cohort study, an ongoing prospective study of the natural and treated histories of HIV, completed a survey about life-course events thought to be related to health. The majority of men resolved IHP over time independent of demographics. Men who resolved IHP had significantly higher odds of positive health outcomes compared to those who did not. These results provide evidence of resilience among participants that is associated with positive health outcomes. Understanding resiliencies and incorporating them into interventions may help to promote health and well-being among gay and bisexual men.

  10. Global Monitoring of Mountain Glaciers Using High-Resolution Spotlight Imaging from the International Space Station

    Science.gov (United States)

    Donnellan, A.; Green, J. J.; Bills, B. G.; Goguen, J.; Ansar, A.; Knight, R. L.; Hallet, B.; Scambos, T. A.; Thompson, L. G.; Morin, P. J.

    2013-12-01

    Mountain glaciers around the world are retreating rapidly, contributing about 20% to present-day sea level rise. Numerous studies have shown that mountain glaciers are sensitive to global environmental change. Temperate-latitude glaciers and snowpack provide water for over 1 billion people. Glaciers are a resource for irrigation and hydroelectric power, but also pose flood and avalanche hazards. Accurate mass balance assessments have been made for only 280 glaciers, yet there are over 130,000 in the World Glacier Inventory. The rate of glacier retreat or advance can be highly variable, is poorly sampled, and inadequately understood. Liquid water from ice front lakes, rain, melt, or sea water and debris from rocks, dust, or pollution interact with glacier ice often leading to an amplification of warming and further melting. Many mountain glaciers undergo rapid and episodic events that greatly change their mass balance or extent but are sparsely documented. Events include calving, outburst floods, opening of crevasses, or iceberg motion. Spaceborne high-resolution spotlight optical imaging provides a means of clarifying the relationship between the health of mountain glaciers and global environmental change. Digital elevation models (DEMs) can be constructed from a series of images from a range of perspectives collected by staring at a target during a satellite overpass. It is possible to collect imagery for 1800 targets per month in the ×56° latitude range, construct high-resolution DEMs, and monitor changes in high detail over time with a high-resolution optical telescope mounted on the International Space Station (ISS). Snow and ice type, age, and maturity can be inferred from different color bands as well as distribution of liquid water. Texture, roughness, albedo, and debris distribution can be estimated by measuring bidirectional reflectance distribution functions (BRDF) and reflectance intensity as a function of viewing angle. The non-sun-synchronous orbit

  11. Ambulatory circadian monitoring (ACM) based on thermometry, motor activity and body position (TAP): a comparison with polysomnography.

    Science.gov (United States)

    Ortiz-Tudela, Elisabet; Martinez-Nicolas, Antonio; Albares, Javier; Segarra, Francesc; Campos, Manuel; Estivill, Eduard; Rol, Maria Angeles; Madrid, Juan Antonio

    2014-03-14

    An integrated variable based on the combination of wrist Temperature, motor Activity and body Position (TAP) was previously developed at our laboratory to evaluate the functioning of the circadian system and sleep-wake rhythm under ambulatory conditions. However, the reliability of TAP needed to be validated with polysomnography (PSG). 22 subjects suffering from sleep disorders were monitored for one night with a temperature sensor (iButton), an actimeter (HOBO) and exploratory PSG. Mean waveforms, sensitivity (SE), specificity (SP), agreement rates (AR) and comparisons between TAP and sleep stages were studied. The TAP variable was optimized for SE, SP and AR with respect to each individual variable (SE: 92%; SP: 78%; AR: 86%). These results improved upon estimates previously published for actigraphy. Furthermore, TAP values tended to decrease as sleep depth increased, reaching the lowest point at phase 3. Finally, TAP estimates for sleep latency (SL: 37±9 min), total sleep time (TST: 367±13 min), sleep efficiency (SE: 86.8±1.9%) and number of awakenings (NA>5 min: 3.3±.4) were not significantly different from those obtained with PSG (SL: 29±4 min; SE: 89.9±1.8%; NA>5 min: 2.3±.4), despite the heterogeneity of the sleep pathologies monitored. The TAP variable is a novel measurement for evaluating circadian system status and sleep-wake rhythms with a level of reliability better to that of actigraphy. Furthermore, it allows the evaluation of a patient's sleep-wake rhythm in his/her normal home environment, and at a much lower cost than PSG. Future studies in specific pathologies would verify the relevance of TAP in those conditions. Copyright © 2014 Elsevier Inc. All rights reserved.

  12. Strategies of internationalization and positioning of brands and products of south of minas gerais in the international market

    Directory of Open Access Journals (Sweden)

    Nilton dos Santos Portugal

    2010-04-01

    Full Text Available The region of the South of Minas Gerais have important polar regions of industrial growth, with segments of intermediate goods of consumption such as nourishing aluminum, electronics, clothes, footwear products and a modern industrial park of pieces to automobile industry. The force of the commerce and the agriculture business are still distinguished. With a US$ 2 billion average monthly, Minas exportations in 2008 grew above national average, the state is the second bigger exporter of the country and the south region its third bigger force (State Secretary of Economic Development - January 2009. In this direction, the study is justified for the fact that it is important to know the strategies used for sucessful companies which act in the international market, being able to serve as research source and parameter for those that have potential for such performance contributing for the development of the e region and economic growth of the country. The work presents a bibliographical revision on internationalization strategies and positioning of value, finishing with a study of multiple cases in two big companies, of the South of Minas Gerais, exporting of finished products, its strategies for the exportations, positioning of its products and brand in the international trade and the restrict factors of this internationalization, as well as its consequences in the development of these organizations.

  13. Validation of the ANDON KD-5915 blood pressure monitor for home blood pressure monitoring according to the European Society of Hypertension International Protocol.

    Science.gov (United States)

    Huang, Qi-Fang; Wang, Jie; Sheng, Chang-Sheng; Zhang, Na-Na; Li, Yan; Wang, Ji-Guang

    2010-08-01

    This study aimed to evaluate the accuracy of the automated oscillometric upper arm blood pressure monitor KD-5915 (ANDON Health, Tianjin, China) for home blood pressure monitoring according to the International Protocol. Systolic and diastolic blood pressures were sequentially measured in 33 adult Chinese individuals using a mercury sphygmomanometer (two observers) and the KD-5915 device (one supervisor). Ninety-nine pairs of comparisons were obtained from 15 participants in phase 1 and the remaining 18 participants in phase 2 of the validation study. Data analysis was performed using the ESHIP Analyzer. The KD-5915 device successfully passed phase 1 of the validation study with a number of absolute differences between the device and observers within 5, 10, and 15 mmHg for at least 27 of 45, 34 of 45, and 43 of 45 measurements, respectively. The device also achieved the targets for phase 2.1, with 66 of 99, 81 of 99, and 95 of 99 device-observer differences within 5, 10, and 15 mmHg, respectively, for systolic blood pressure, and with 79 of 99, 95 of 99, and 99 of 99 differences within 5, 10, and 15 mmHg, respectively, for diastolic blood pressure. In phase 2.2, 23, and 27 participants had at least two of the three device-observer differences within 5 mmHg (required Z22) for systolic blood pressure and diastolic blood pressure, respectively. The ANDON upper arm blood pressure monitor KD-5915 has passed the International Protocol requirements, and hence can be recommended for use at home in adults.

  14. Real-time monitoring of position and motion of a non-stationary object with a highly sensitive magnetic impedance sensor

    Directory of Open Access Journals (Sweden)

    O. Thiabgoh

    2018-03-01

    Full Text Available The real-time monitoring of the position and speed of a moving object is crucial for safety compliance in industrial applications. The effectiveness of current sensing technology is limited by sensing distance and messy environments. In this work, a position and speed sensor based on the giant magneto-impedance effect was fabricated using a Joule annealed Co-rich magnetic microwire. The fabricated GMI sensor response was explored over a frequency range of 1 MHz–1 GHz. The impedance spectrum showed a high GMI ratio and high field sensitivity response at low magnetic fields. The GMI sensor based longitudinal effect was found to be more sensitive than a commercial Gaussmeter. The practical utility of the high sensitivity of the sensor at weak magnetic fields for far-off distance monitoring of position and speed was demonstrated. This GMI-based sensor is highly promising for real-time position detection and oscillatory motion monitoring. Keywords: Real-time monitoring, Position and speed sensor, Oscillatory motion, Vibration monitoring, RF magnetic sensor, High-frequency magneto-impedance, PACS: 75.50.Kj

  15. Suitability of monitoring methods for the optimisation of Radiological Protection in the case of internal exposure through inhalation

    International Nuclear Information System (INIS)

    Degrange, J.P.; Gibert, B.; Basire, D.

    2000-01-01

    The radiological protection system recommended by the International Commission for Radiological Protection (ICRP) for justified practices relied pn the limitation and optimisation principles. The monitoring of internal exposure is most often based on the periodic assessment of individual exposure in order to essentially insure the simple compliance with the annual dose limits. Optimisation of protection implies a realistic, sensitive and analytical assessment of individual and collective exposures in order to allow the indentification of the main sources of exposure (main sources of contamination, most exposed operators, work activities contributing the most to the exposure) and the selection of the optimal protection options. Therefore the monitoring methods must allow the realistic assessment of individual dose levels far lower than annual limits together with measurements as frequent as possible. The aim of this presentation is to discuss the ability of various monitoring methods (collective and individual air sampling, in vivo and in vitro bioassays) to fulfil those needs. This discussion is illustrated by the particular case of the internal exposure to natural uranium compounds through inhalation. Firstly, the sensitivity and the degree to which each monitoring method is realistic are quantified and discussed on the basis of the application of the new ICRP dosimetric model, and their analytical capability for the optimisation of radiological protection is then indicated. Secondly, a case study is presented which shows the capability of individual air sampling techniques to analyse the exposure of the workers and the inadequacy of static air sampling to accurately estimate the exposures when contamination varies significantly over time and space in the workstations. As far as exposure to natural uranium compounds through inhalation is concerned, the study for assessing the sensitivity, analytic ability and accuracy of the different measuring systems shows that

  16. CT evaluation of patient deep inspiration self-breath-holding: How precisely can patients reproduce the tumor position in the absence of respiratory monitoring devices?

    International Nuclear Information System (INIS)

    Onishi, Hiroshi; Kuriyama, Kengo; Komiyama, Takafumi; Tanaka, Shiho; Ueki, Junko; Sano, Naoki; Araki, Tsutomu; Ikenaga, Satoshi; Tateda, Yoshihito; Aikawa, Yoshihito

    2003-01-01

    tumor position under self-breath-holding by patients during deep inspiration after sufficient practice and in the absence of respiratory monitoring devices was satisfactorily accurate, and differences in tumor position were smaller under breath-holding using the Active mode than using the Passive mode. We believe this new technique is likely to prove extremely useful for the irradiation of lung tumors with a small internal margin and for reduced proportion of high-dose irradiated normal lung to total lung volume

  17. Thermal management and prototype testing of Compton scattering X-ray beam position monitor for the Advanced Photon Source Upgrade

    Science.gov (United States)

    Lee, S. H.; Yang, B. X.; Collins, J. T.; Ramanathan, M.

    2017-02-01

    Accurate and stable x-ray beam position monitors (XBPMs) are key elements in obtaining the desired user beam stability in the Advanced Photon Source Upgrade. In the next-generation XBPMs for the canted-undulator front ends, where two undulator beams are separated by 1.0 mrad, the lower beam power (changes through the interface via thermal simulations, the thermal contact resistance (TCR) of TIMs at an interface between two solid materials under even contact pressure must be known. This paper addresses the TCR measurements of several TIMs, including gold, silver, pyrolytic graphite sheet, and 3D graphene foam. In addition, a prototype of a Compton-scattering XBPM with diamond blades was installed at APS Beamline 24-ID-A in May 2015 and has been tested. This paper presents the design of the Compton-scattering XBPM, and compares thermal simulation results obtained for the diamond blade of this XBPM by the finite element method with in situ empirical measurements obtained by using reliable infrared technology.

  18. Enhanced 911/global position system wizard: a telemedicine application for the prevention of severe hypoglycemia--monitor, alert, and locate.

    Science.gov (United States)

    Dassau, Eyal; Jovanovic, Lois; Doyle, Francis J; Zisser, Howard C

    2009-11-01

    Intensive insulin therapy has an inherent risk of hypoglycemia that can lead to loss of consciousness, cardiac arrhythmia, seizure, and death ("dead-in-bed syndrome"). This risk of hypoglycemia is a major concern for patients, families, and physicians. The need for an automated system that can alert in the event of severe hypoglycemia is evident. In engineering systems, where there is a risk of malfunction of the primary control system, alert and safety mechanisms are implemented in layers of protection. This concept has been adopted in the proposed system that integrates a hypoglycemia prediction algorithm with a global position system (GPS) locator and short message service such that the current glucose value with the rate of change (ROC) and the location of the subject can be communicated to a predefined list. Furthermore, if the system is linked to the insulin pump, it can suspend the pump or decrease the basal insulin infusion rate to prevent the pending event. The system was evaluated on clinical datasets of glucose tracings from the DexCom Seven system. Glucose tracings were analyzed for hypoglycemia events and then a text message was broadcast to a predefined list of people who were notified with the glucose value, ROC, GPS coordinates, and a Google map of the location. In addition to providing a safety layer to a future artificial pancreas, this system also can be easily implemented in current continuous glucose monitors to help provide information and alerts to people with diabetes.

  19. An OpenMP Parallelisation of Real-time Processing of CERN LHC Beam Position Monitor Data

    CERN Document Server

    Renshall, H

    2012-01-01

    SUSSIX is a FORTRAN program for the post processing of turn-by-turn Beam Position Monitor (BPM) data, which computes the frequency, amplitude, and phase of tunes and resonant lines to a high degree of precision. For analysis of LHC BPM data a specific version run through a C steering code has been implemented in the CERN Control Centre to run on a server under the Linux operating system but became a real time computational bottleneck preventing truly online study of the BPM data. Timing studies showed that the independent processing of each BPMs data was a candidate for parallelization and the Open Multiprocessing (OpenMP) package with its simple insertion of compiler directives was tried. It proved to be easy to learn and use, problem free and efficient in this case reaching a factor of ten reductions in real-time over twelve cores on a dedicated server. This paper reviews the problem, shows the critical code fragments with their OpenMP directives and the results obtained.

  20. Validation of an Internet-Based Long Version of the International Physical Activity Questionnaire in Danish Adults Using Combined Accelerometry and Heart Rate Monitoring

    DEFF Research Database (Denmark)

    Hansen, Andreas Wolff; Dahl-Petersen, Inger; Helge, Jørn Wulff

    2014-01-01

    BACKGROUND: The International Physical Activity Questionnaire (IPAQ) is commonly used in surveys but reliability and validity has not been established in the Danish population. METHODS: Among participants in the Danish Health Examination survey 2007-2008, 142 healthy participants (45% men) wore...... a unit that combined accelerometry and heart rate monitoring (Acc+HR) for 7 consecutive days and then completed the IPAQ. Background data were obtained from the survey. Physical activity energy expenditure (PAEE) and time in moderate, vigorous and sedentary intensity level were derived from the IPAQ...... and compared with estimates from Acc+HR using Spearman´s correlation coefficients and Bland-Altman plots. Repeatability of the IPAQ was also assessed. RESULTS: PAEE from the two methods was significantly positively correlated (0.28 and 0.49 for women and men, respectively). Men significantly overestimated PAEE...

  1. CTBTO international monitoring system: Status of work in Cameroon and perspectives

    International Nuclear Information System (INIS)

    Nyobe, J.B.

    2002-01-01

    The presentation outlines Cameroon's participation in CTBTO programme and its seismic activities. Areas of inter-regional and international cooperation are described. Suggestions are made on ways in which Cameroon can contribute to the work of the commission

  2. International Energy Agency (IEA) Greenhouse Gas (GHG) Weyburn-Midale CO₂ Monitoring and Storage Project

    Energy Technology Data Exchange (ETDEWEB)

    Sacuta, Norm [Petroleum Technology Research Centre Incorporated, Saskatchewan (Canada); Young, Aleana [Petroleum Technology Research Centre Incorporated, Saskatchewan (Canada); Worth, Kyle [Petroleum Technology Research Centre Incorporated, Saskatchewan (Canada)

    2015-12-22

    The IEAGHG Weyburn-Midale CO₂ Monitoring and Storage Project (WMP) began in 2000 with the first four years of research that confirmed the suitability of the containment complex of the Weyburn oil field in southeastern Saskatchewan as a storage location for CO₂ injected as part of enhanced oil recovery (EOR) operations. The first half of this report covers research conducted from 2010 to 2012, under the funding of the United States Department of Energy (contract DEFE0002697), the Government of Canada, and various other governmental and industry sponsors. The work includes more in-depth analysis of various components of a measurement, monitoring and verification (MMV) program through investigation of data on site characterization and geological integrity, wellbore integrity, storage monitoring (geophysical and geochemical), and performance/risk assessment. These results then led to the development of a Best Practices Manual (BPM) providing oilfield and project operators with guidance on CO₂ storage and CO₂-EOR. In 2013, the USDOE and Government of Saskatchewan exercised an optional phase of the same project to further develop and deploy applied research tools, technologies, and methodologies to the data and research at Weyburn with the aim of assisting regulators and operators in transitioning CO₂-EOR operations into permanent storage. This work, detailed in the second half of this report, involves seven targeted research projects – evaluating the minimum dataset for confirming secure storage; additional overburden monitoring; passive seismic monitoring; history-matched modelling; developing proper wellbore design; casing corrosion evaluation; and assessment of post CO₂-injected core samples. The results from the final and optional phases of the Weyburn-Midale Project confirm the suitability of CO₂-EOR fields for the injection of CO₂, and further, highlight the necessary MMV and follow-up monitoring required for these operations to be considered

  3. Turning process monitoring of internal combustion engine piston’s cylindrical surface

    Directory of Open Access Journals (Sweden)

    Twardowski Pawel

    2017-01-01

    Full Text Available In this paper the monitoring method of turning process of combustion engine piston’s cylindrical surface is proposed. During this process, the PCD diamond tool cuts the piston’s cylindrical surface with the 3 grooves. The first groove is made in the cast iron insert. In case, when the machining allowances are selected inappropriately, the tool cuts the cast iron insert and consequently generates the reject. The proposed monitoring system based on vibration signals analysis enables the detection of these critical situations and react, in order to maintain the production quality.

  4. Performance Evaluation of the Operational Air Quality Monitor for Water Testing Aboard the International Space Station

    Science.gov (United States)

    Wallace, William T.; Limero, Thomas F.; Gazda, Daniel B.; Minton, John M.; Macatangay, Ariel V.; Dwivedi, Prabha; Fernandez, Facundo M.

    2014-01-01

    Real-time environmental monitoring on ISS is necessary to provide data in a timely fashion and to help ensure astronaut health. Current real-time water TOC monitoring provides high-quality trending information, but compound-specific data is needed. The combination of ETV with the AQM showed that compounds of interest could be liberated from water and analyzed in the same manner as air sampling. Calibration of the AQM using water samples allowed for the quantitative analysis of ISS archival samples. Some calibration issues remain, but the excellent accuracy of DMSD indicates that ETV holds promise for as a sample introduction method for water analysis in spaceflight.

  5. Evaluating dosage effects for the positive action program: How implementation impacts internalizing symptoms, aggression, school hassles, and self-esteem.

    Science.gov (United States)

    Smokowski, Paul R; Guo, Shenyang; Wu, Qi; Evans, Caroline B R; Cotter, Katie L; Bacallao, Martica

    2016-01-01

    Positive Action (PA) is a school-based intervention for elementary-, middle-, and high-school students that aims to decrease problem behaviors (e.g., violence, substance use) and increase positive behaviors (e.g., academic achievement, school engagement). PA has a long history of documented success achieving these aims, making it an Evidence Based Practice (EBP). Intervention research on EBP's has established the importance of implementation fidelity, especially with regard to program dosage; failure to properly implement an EBP can have negative consequences on targeted outcomes, especially if participants are exposed to a low dosage of the program (e.g., fewer lessons than specified). Much of the current research on PA has neglected to examine how program dosage impacts PA's effect on targeted outcomes. Using propensity score models, multiple imputation, and a 2-level hierarchical linear model, the current study fills this gap and examines how different dosages of PA as measured by years participating in PA and number of PA lessons, impacts adolescent internalizing symptoms, aggression, perceptions of school hassles, and self-esteem over a 3-year period. The current sample included middle school students in grades 6, 7, and 8 (N = 5,894). The findings indicate that students who received 3 years of the PA intervention and a high number of PA lessons had a significantly higher self-esteem score than those who received 0 years of PA or zero lessons. Participants who received 1 year of PA also reported significantly lower school hassle scores than those who received 0 years. Dosage had no statistically significant effects on aggression or internalizing score. Implications are discussed. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

  6. Positive predictive value of the International Classification of Diseases, 10th edition diagnosis codes for anemia caused by bleeding in the Danish National Registry of Patients.

    Science.gov (United States)

    Zalfani, Jihen; Frøslev, Trine; Olsen, Morten; Ben Ghezala, Inès; Gammelager, Henrik; Arendt, Johan Fb; Erichsen, Rune

    2012-01-01

    Valid data on anemia caused by bleeding are needed for epidemiological research and monitoring health care. The Danish National Registry of Patients (DNRP) is a nationwide medical database with information on all Danish residents' hospital history. We aimed to assess the positive predictive value (PPV) of the diagnostic coding of anemia caused by bleeding in the DNRP. In the DNRP, we identified all patients with International Classification of Disease, 10th edition codes for anemia caused by bleeding (acute: D50.0; chronic: D62.6) at three Danish hospitals from 2000 through 2009. For these patients we computed the PPV using hemoglobin level data, from Aarhus University laboratory database, as reference standard. Anemia was defined by a hemoglobin level less than 7.0 mmol/L for women and less than 8.0 mmol/L for men. We identified 3391 patients in the DNRP with a diagnosis of anemia caused by bleeding. The overall PPV was 95.4% (95% confidence interval [CI]: 94.6%-96.0%). The PPV was 97.6% (95% CI: 96.6%-98.3%) for men and 94.0% (95% CI: 92.9%-94.9%) for women, and the PPV increased with age at diagnosis. The PPV varied according to type of discharging departments, from 89.2% (95% CI: 83.4%-93.4%) in gynecology to 96.8% (95% CI: 94.9%-98.2%) in surgery, and was lower for outpatients compared with inpatients. We found a high PPV of the coding for anemia caused by bleeding in the DNRP. The registry is a valid source of data on anemia caused by bleeding for various purposes including research and monitoring health care.

  7. The Second-Image Reversed and Climate Policy: How International Influences Helped Changing Brazil’s Positions on Climate Change

    Directory of Open Access Journals (Sweden)

    Sjur Kasa

    2013-03-01

    Full Text Available International climate policy over the last 7–8 years has been characterized by the increasing involvement of developing countries. While COP-13 at Bali marked a stronger willingness to participate in mitigation efforts in principle, there are now numerous examples of domestic programs for mitigation by this group of countries. Brazil has gone furthest among developing countries, with a substantial voluntary commitment to reduce its emissions proclaimed in 2009. The dynamics behind the change in Brazil’s position are discussed, with a particular eye to the effects of international influences. In conjunction with important domestic changes, a set of interacting influences through a variety of pathways both changed preferences among important interest groups in Brazilian society towards favoring some kind of commitments and helped to change the structure of government forums and decision-making rules in a way that empowered reform-minded ministries. It is argued that this perspective, drawn from Peter Gourevitch’s idea of the “second image reversed”, is increasingly relevant for understanding the influence of the broad “regime complex” on climate change on politics in developing countries.

  8. Negative and positive participant responses to the composite international diagnostic interview - Results of the Netherlands Mental Health Survey and Incidence Study

    NARCIS (Netherlands)

    Graaf, R. de; Have, M.L. ten; Dorsselaer, S.A.F.M. van; Schoemaker, C.G.; Vollebergh, W.A.M.

    2004-01-01

    Little is known about the emotional responses of participants in community surveys to standardised psychiatric interviews like the Composite International Diagnostic Interview (CIDI). This study investigates the proportion of subjects responding negatively or positively to the CIDI, and identifies

  9. Fertilia: a European International Cooperation (INCO EU) project for monitoring trace elements in agricultural ecosystems

    Czech Academy of Sciences Publication Activity Database

    Marmiroli, N.; Maestri, E.; Mucchino, C.; Antonioli, G.; Marmiroli, M.; Izquierdo, C. G.; Hernandez, T.; Waclawek, W.; Mocko, A.; Bozym, M.; Nowak, A.; Nowak, J.; Večeřa, Zbyněk; Dočekal, Bohumil

    2001-01-01

    Roč. 13, č. 1 (2001), s. 41-54 ISSN 1120-4826 Grant - others:Copernicus(BE) ERB IC-15-CT98-0124 Institutional research plan: CEZ:AV0Z4031919 Keywords : monitoring * trace elements * agricultural ecosystems Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 0.207, year: 2001

  10. Selection criteria for patients with chronic ankle instability in controlled research: a position statement of the international ankle consortium

    NARCIS (Netherlands)

    Gribble, P.A.; Delahunt, E.; Bleakley, C.; Caulfield, B.; Docherty, C.L.; Fourchet, F.; Fong, D.; Hertel, J.; Hiller, C.; Kaminski, T.W.; McKeon, P.O.; Refshauge, K.M.; Wees, P.J. van der; Vicenzino, B.; Wikstrom, E.A.

    2013-01-01

    The International Ankle Consortium is an international community of researchers and clinicians whose primary scholastic purpose is to promote scholarship and dissemination of research-informed knowledge related to pathologies of the ankle complex. The constituents of the International Ankle

  11. A Study on the Optimal Positions of ECG Electrodes in a Garment for the Design of ECG-Monitoring Clothing for Male.

    Science.gov (United States)

    Cho, Hakyung; Lee, Joo Hyeon

    2015-09-01

    Smart clothing is a sort of wearable device used for ubiquitous health monitoring. It provides comfort and efficiency in vital sign measurements and has been studied and developed in various types of monitoring platforms such as T-shirt and sports bra. However, despite these previous approaches, smart clothing for electrocardiography (ECG) monitoring has encountered a serious shortcoming relevant to motion artifacts caused by wearer movement. In effect, motion artifacts are one of the major problems in practical implementation of most wearable health-monitoring devices. In the ECG measurements collected by a garment, motion artifacts are usually caused by improper location of the electrode, leading to lack of contact between the electrode and skin with body motion. The aim of this study was to suggest a design for ECG-monitoring clothing contributing to reduction of motion artifacts. Based on the clothing science theory, it was assumed in this study that the stability of the electrode in a dynamic state differed depending on the electrode location in an ECG-monitoring garment. Founded on this assumption, effects of 56 electrode positions were determined by sectioning the surface of the garment into grids with 6 cm intervals in the front and back of the bodice. In order to determine the optimal locations of the ECG electrodes from the 56 positions, ECG measurements were collected from 10 participants at every electrode position in the garment while the wearer was in motion. The electrode locations indicating both an ECG measurement rate higher than 80.0 % and a large amplitude during motion were selected as the optimal electrode locations. The results of this analysis show four electrode locations with consistently higher ECG measurement rates and larger amplitudes amongst the 56 locations. These four locations were abstracted to be least affected by wearer movement in this research. Based on this result, a design of the garment-formed ECG monitoring platform

  12. Validation of the Andon KD-5965 upper-arm blood pressure monitor for home blood pressure monitoring according to the European Society of Hypertension International Protocol revision 2010.

    Science.gov (United States)

    Huang, Jinhua; Li, Zhijie; Li, Guimei; Liu, Zhaoying

    2015-10-01

    This study aimed to evaluate the accuracy of the Andon KD-5965 upper-arm blood pressure monitor according to the European Society of Hypertension International Protocol revision 2010. Systolic and diastolic blood pressures were sequentially measured in 33 adults, with 20 women using a mercury sphygmomanometer (two observers) and the Andon KD-5965 device (one supervisor). A total of 99 pairs of comparisons were obtained from 33 participants for judgments in two parts with three grading phases. The device achieved the targets in part 1 of the validation study. The number of absolute differences between the device and observers within 5, 10, and 15 mmHg was 70/99, 91/99, and 98/99, respectively, for systolic blood pressure and 81/99, 99/99, and 99/99, respectively, for diastolic blood pressure. The device also fulfilled the criteria in part 2 of the validation study. Twenty-five and 29 participants, for systolic and diastolic blood pressure, respectively, had at least two of the three device-observers differences within 5 mmHg (required≥24). Two and one participants for systolic and diastolic blood pressure, respectively, had all three device-observers comparisons greater than 5 mmHg. According to the validation results, with better performance for diastolic blood pressure than that for systolic blood pressure, the Andon automated oscillometric upper-arm blood pressure monitor KD-5965 fulfilled the requirements of the European Society of Hypertension International Protocol revision 2010, and hence can be recommended for blood pressure measurement in adults.

  13. Substance Use Among Nurses and Nursing Students: A Joint Position Statement of the Emergency Nurses Association and the International Nurses Society on Addictions.

    Science.gov (United States)

    Strobbe, Stephen; Crowley, Melanie

    Alcohol and other substance use by nurses potentially places patients, the public, and nurses themselves at risk for serious injury or death. Nursing students are also at risk for problems related to substance use. When viewed and treated as a chronic medical illness, treatment outcomes for substance use disorders are comparable with those of other diseases and can result in lasting benefits. Professional monitoring programs that employ an alternative-to-discipline approach have been shown to be effective in the treatment of health professionals with substance use disorders and are considered a standard for recovery, with high rates of completion and return to practice. It is the position of the Emergency Nurses Association and the International Nurses Society on Addictions that 1. health care facilities provide education to nurses and other employees regarding alcohol and other drug use and establish policies, procedures, and practices to promote safe, supportive, drug-free workplaces; 2. health care facilities and schools of nursing adopt alternative-to-discipline approaches to treating nurses and nursing students with substance use disorders, with stated goals of retention, rehabilitation, and reentry into safe, professional practice; 3. drug diversion, in the context of personal use, is viewed primarily as a symptom of a serious and treatable disease and not exclusively as a crime; and 4. nurses and nursing students are aware of the risks associated with substance use, impaired practice, and drug diversion and have the responsibility and means to report suspected or actual concerns.

  14. Growth and endocrine disorders in thalassemia: The international network on endocrine complications in thalassemia (I-CET position statement and guidelines

    Directory of Open Access Journals (Sweden)

    Vincenzo De Sanctis

    2013-01-01

    Full Text Available The current management of thalassemia includes regular transfusion programs and chelation therapy. It is important that physicians be aware that endocrine abnormalities frequently develop mainly in those patients with significant iron overload due to poor compliance to treatment, particularly after the age of 10 years. Since the quality of life of thalassemia patients is a fundamental aim, it is vital to monitor carefully their growth and pubertal development in order to detect abnormalities and to initiate appropriate and early treatment. Abnormalities should be identified and treatment initiated in consultation with a pediatric or an adult endocrinologist and managed accordingly. Appropriate management shall put in consideration many factors such as age, severity of iron overload, presence of chronic liver disease, thrombophilia status, and the presence of psychological problems. All these issues must be discussed by the physician in charge of the patient′s care, the endocrinologist and the patient himself. Because any progress in research in the field of early diagnosis and management of growth disorders and endocrine complications in thalassemia should be passed on to and applied adequately to all those suffering from the disease, on the 8 May 2009 in Ferrara, the International Network on Endocrine Complications in Thalassemia (I-CET was founded in order to transmit the latest information on these disorders to the treating physicians. The I-CET position statement outlined in this document applies to patients with transfusion-dependent thalassemia major to help physicians to anticipate, diagnose, and manage these complications properly.

  15. Mercury in fish from two Nicaraguan lakes: A recommendation for increased monitoring of fish for international commerce

    Energy Technology Data Exchange (ETDEWEB)

    McCrary, Jeffrey K. [University of Central America, Apdo. 69, Managua (Nicaragua) and College of Natural Resources, Virginia Tech, Blacksburg, VA 24061 (United States)]. E-mail: jmccrary2@yahoo.com; Castro, Mark [Appalachian Laboratory, University of Maryland Center for Environmental Science, 301 Braddock Road, Frostburg, MD 21532 (United States); McKaye, Kenneth R. [University of Central America, Apdo. 69, Managua (Nicaragua); Appalachian Laboratory, University of Maryland Center for Environmental Science, 301 Braddock Road, Frostburg, MD 21532 (United States)

    2006-06-15

    We measured total mercury concentrations in water and fish of Lake Managua and Lake Apoyo. Water mercury concentrations were 10-fold higher in Lake Managua than in Lake Apoyo, although differences in mercury concentration in the most common native fish were not significant. One-fourth of the commercially fished tilapia in Lake Managua exceeded maximum recommended mercury levels for consumption among pregnant women and other at-risk groups, although bioavailability to fishes was lower than in previously studied sites in Brazil and Western Maryland. The lower bioavailiability may present important information for management options to reduce mercury exposure to fishes and humans. We recommend closer mercury monitoring among freshwater fish destined for international commerce. - Fish commonly exported into the international food supply may be contaminated with mercury.

  16. Mercury in fish from two Nicaraguan lakes: A recommendation for increased monitoring of fish for international commerce

    International Nuclear Information System (INIS)

    McCrary, Jeffrey K.; Castro, Mark; McKaye, Kenneth R.

    2006-01-01

    We measured total mercury concentrations in water and fish of Lake Managua and Lake Apoyo. Water mercury concentrations were 10-fold higher in Lake Managua than in Lake Apoyo, although differences in mercury concentration in the most common native fish were not significant. One-fourth of the commercially fished tilapia in Lake Managua exceeded maximum recommended mercury levels for consumption among pregnant women and other at-risk groups, although bioavailability to fishes was lower than in previously studied sites in Brazil and Western Maryland. The lower bioavailiability may present important information for management options to reduce mercury exposure to fishes and humans. We recommend closer mercury monitoring among freshwater fish destined for international commerce. - Fish commonly exported into the international food supply may be contaminated with mercury

  17. Sea floor litter monitored using catches of the International Bottom Trawl Survey

    OpenAIRE

    Hal, van, R.

    2015-01-01

    The Marine Strategy Framework Directive (MSFD) requires from the European Member States to develop programmes of measures to achieve or maintain Good Environmental Status (GES) in European Seas. To be able to evaluate the quality state and trends of the marine waters on a regular basis and the effect of measures, monitoring programs for MSFD descriptors and indicators have been established by the Member states. GES is described by 11 descriptors, and marine litter is one of them. The Dutch mo...

  18. AN INTERNATIONAL COOPERATION BY USING AN ALL-ENCOMPASSING PASSIVE RADON MONITOR.

    Science.gov (United States)

    Tommasino, L; Chen, J; Falcomer, R; Janik, M; Kanda, R; DeFelice, F; Cardellini, F; Trevisi, R; Leonardi, F; Magnoni, M; Chiaberto, E; Agnesod, G; Ragani, M Faure; Espinosa, G; Golzarri, J; Kozak, K; Mazur, J

    2017-11-01

    The recently developed radon film-badge makes it possible to measure radon indoors, in soil, in water and/or in aqueous media (e.g. mud). As a result of its wide response linearity, this monitor has been successfully used to measure radon in-water with concentrations from 10 to ~10 000 Bq/L. By exploiting the unique characteristics of this badge, a mini-survey has been carried out by Health Canada in which radon in water was measured from 12 private wells, as well as in tap water originating from the Ottawa River. Due to the widespread interest of different laboratories in using these passive monitors, laboratories were provided with plastic films to construct their own badges by using in-house CR-39 detectors. Monitors were then irradiated by a known radon concentration at the National Institute of Radiation Metrology (ENEA)'s radon chamber and sent back to each laboratory for processing and counting. Even though these laboratories have been using different etching- and counting-procedures, the film-badge responses varied only within ~12%. © The Author 2017. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  19. An international cooperation by using an all-encompassing passive radon monitor

    International Nuclear Information System (INIS)

    Tommasino, L.; Chen, J.; Falcomer, R.; Janik, M.; Kanda, R.; DeFelice, F.; Cardellini, F.; Trevisi, R.; Leonardi, F.; Magnoni, M.; Chiaberto, E.; Agnesod, G.; Ragani, M. Faure; Espinosa, G.; Golzarri, J.; Kozak, K.; Mazur, J.

    2017-01-01

    The recently developed radon film-badge makes it possible to measure radon indoors, in soil, in water and/or in aqueous media (e.g. mud). As a result of its wide response linearity, this monitor has been successfully used to measure radon in-water with concentrations from 10 to ∼10 000 Bq/L. By exploiting the unique characteristics of this badge, a mini-survey has been carried out by Health Canada in which radon in water was measured from 12 private wells, as well as in tap water originating from the Ottawa River. Due to the widespread interest of different laboratories in using these passive monitors, laboratories were provided with plastic films to construct their own badges by using in-house CR-39 detectors. Monitors were then irradiated by a known radon concentration at the National Institute of Radiation Metrology (ENEA) s radon chamber and sent back to each laboratory for processing and counting. Even though these laboratories have been using different etching- and counting procedures, the film-badge responses varied only within ∼12%. (authors)

  20. Polycyclic Aromatic Hydrocarbons (PAHs) and Hopanes in Plastic Resin Pellets as Markers of Oil Pollution via International Pellet Watch Monitoring.

    Science.gov (United States)

    Yeo, Bee Geok; Takada, Hideshige; Hosoda, Junki; Kondo, Atsuko; Yamashita, Rei; Saha, Mahua; Maes, Thomas

    2017-08-01

    Oil pollution in the marine environment is an unavoidable problem due to chronic input from local sources, particularly in urban areas and oil spills. Oil pollution not only causes immediate physical damages to surrounding wildlife but also some components, including higher molecular weight PAHs, can persist in the environment for many years and pose insidious threats to the ecosystem. Long-term and nontargeted monitoring of oil pollution is important. This paper examines the ability of International Pellet Watch (IPW) for initial identification and monitoring of oil pollution by analysing PAHs and hopanes in plastic pellet samples collected globally by volunteers. PAH concentrations with the sum of 28 parent and methyl PAHs vary geographically, ranging from 0.035 to 24.4 µg/g-pellet, in line with the presence or absence of local oil pollution sources, such as oil refineries or oil spill sites. This suggests that PAHs can be used to monitor petroleum pollution in IPW. A colour-coded categorization for PAH concentrations within IPW monitoring also is established to facilitate data presentation and understanding. PAH concentrations are generally higher in Western Europe, especially around the North Sea shorelines, moderate in East Asia and North America, and lower in South East Asia, Oceania, South America, and Africa. Hopane concentrations, with a smaller spatial variation (1.7-101 µg/g-pellet), showed no spatial pattern. This result and the poor correlation between hopanes and PAHs suggest that hopane concentrations alone are unsuited to identify petroleum pollution. However, hopane compositions can be used for fingerprinting sources of oil pollution. Thus, both PAHs and hopanes in IPW allow for low cost, remote monitoring of global oil pollution.

  1. Assessing worst case scenarios in movement demands derived from global positioning systems during international rugby union matches: Rolling averages versus fixed length epochs

    Science.gov (United States)

    Cunningham, Daniel J.; Shearer, David A.; Carter, Neil; Drawer, Scott; Pollard, Ben; Bennett, Mark; Eager, Robin; Cook, Christian J.; Farrell, John; Russell, Mark

    2018-01-01

    The assessment of competitive movement demands in team sports has traditionally relied upon global positioning system (GPS) analyses presented as fixed-time epochs (e.g., 5–40 min). More recently, presenting game data as a rolling average has become prevalent due to concerns over a loss of sampling resolution associated with the windowing of data over fixed periods. Accordingly, this study compared rolling average (ROLL) and fixed-time (FIXED) epochs for quantifying the peak movement demands of international rugby union match-play as a function of playing position. Elite players from three different squads (n = 119) were monitored using 10 Hz GPS during 36 matches played in the 2014–2017 seasons. Players categorised broadly as forwards and backs, and then by positional sub-group (FR: front row, SR: second row, BR: back row, HB: half back, MF: midfield, B3: back three) were monitored during match-play for peak values of high-speed running (>5 m·s-1; HSR) and relative distance covered (m·min-1) over 60–300 s using two types of sample-epoch (ROLL, FIXED). Irrespective of the method used, as the epoch length increased, values for the intensity of running actions decreased (e.g., For the backs using the ROLL method, distance covered decreased from 177.4 ± 20.6 m·min-1 in the 60 s epoch to 107.5 ± 13.3 m·min-1 for the 300 s epoch). For the team as a whole, and irrespective of position, estimates of fixed effects indicated significant between-method differences across all time-points for both relative distance covered and HSR. Movement demands were underestimated consistently by FIXED versus ROLL with differences being most pronounced using 60 s epochs (95% CI HSR: -6.05 to -4.70 m·min-1, 95% CI distance: -18.45 to -16.43 m·min-1). For all HSR time epochs except one, all backs groups increased more (p < 0.01) from FIXED to ROLL than the forward groups. Linear mixed modelling of ROLL data highlighted that for HSR (except 60 s epoch), SR was the only group not

  2. Fault detection and diagnosis for compliance monitoring in international supply chains

    NARCIS (Netherlands)

    Wang, Yuxin; Tian, Yifu; Teixeira, André; Hulstijn, Joris; Tan, Yao-Hua

    Currently international supply chains are facing risks concerning faults in compliance, such as altering shipping documentations, fictitious inventory, and inter-company manipulations. In this paper a method to detect and diagnose fault scenarios regarding customs compliance in supply chains is

  3. Monitoring the International Monetary System: Its Development in the West, and Future in the East

    Directory of Open Access Journals (Sweden)

    Todd J. Barry

    2016-06-01

    Full Text Available The “gold standard” is frequently mentioned in text books, but few without an economics background can fully understand it. This paper thus begins in 1896, when U.S. Presidential candidate William Jennings Bryan declared, “You shall not crucify mankind on a cross of gold.” Since going back to the middle ages, the world has had numerous monetary systems, which are here explained in comprehensible terms. A modern reoccurring idea is to return to some form of the gold standard, while some argue for switching to the Chinese yuan or another international reserve currency, which the International Monetary Fund (IMF will adopt in their Special Drawing Rights starting in October, 2016. This paper is normative in that it comments on the current international structure, but uses economic principles to support its argument in favor of an internationally strong dollar. It thus traces the history of a topically contentious subject, with a basic regression indicating important predictive factors for the future. It offers that a new gold standard would not be in the world’s interest, interfering with monetary policy, while emerging market countries would be best to import more and financially deepen, which the regression shows was why the Chinese yuan was adopted by the IMF, then looking ahead to other parts of Asia and towards bitcoins.

  4. Use of Mobile Technology for Monitoring and Evaluation in International Health and Development Programs

    Science.gov (United States)

    Bruce, Kerry

    2013-01-01

    Background: Mobile phones and other technologies are widely used in health programming in developing countries, many introduced by international nongovernmental organizations (INGOs) to accelerate data collection. This research examined: How are INGOs adopting the innovation of mobile technology into M&E systems for health care programs in…

  5. 2000 Volvo Award winner in biomechanical studies: Monitoring in vivo implant loads with a telemeterized internal spinal fixation device.

    Science.gov (United States)

    Rohlmann, A; Graichen, F; Weber, U; Bergmann, G

    2000-12-01

    Implant loads were measured in 10 patients using telemeterized internal spinal fixation devices. To determine the postoperative temporal course of implant loads. Little information exists regarding the temporal course of loads on internal spinal fixation devices. The telemeterized internal spinal fixator allows the measurement of three force components and three moments acting in the fixator. Implant loads were determined in up to 20 measuring sessions for different activities, including walking, standing, sitting, lying in the supine position, and lifting an extended leg while in the supine position. Implant loads often increased shortly after anterior interbody fusion was performed. Several patients retained the same high level even after fusion had taken place. This explains the reason why screw breakage sometimes occurs more than half a year after implantation. The time of fusion could not be pinpointed from the loading curves. The results show that fixators may be highly loaded even after fusion has occurred. A flexion bending moment acts on the implant even with the body in a relaxed lying position. This means that already shortly after the anterior procedure, the shape of the spine is not neutral and unloaded, but slightly deformed, which loads the fixators. Pedicle screw breakage more than half a year after insertion does not prove that anterior interbody fusion has not occurred.

  6. Results of the Ongoing Monitoring of the Position of a Geostationary Telecommunication Satellite by the Method of Spatially Separated Basis Receiving of Digital Satellite Television Signals

    Directory of Open Access Journals (Sweden)

    Bushuev F.

    2016-10-01

    Full Text Available The results of the ongoing monitoring of the position of geostationary telecommunication satellite Eutelsat-13B (13° East are presented in the article. The results were obtained using a radio engineering complex (RC of four stations receiving digital satellite television and a data processing centre. The stations are located in Kyiv, Mukachevo, Kharkiv and Mykolaiv.

  7. Development of a Versatile Ultrasonic Internal Pipe/Vessel Component Monitor for In-Service Inspection of Nuclear Reactor Components

    Energy Technology Data Exchange (ETDEWEB)

    Searfass, Clifford T. [Structural Integrity Associates, Inc., State College, PA (United States); Malinowski, Owen M. [Structural Integrity Associates, Inc., State College, PA (United States); Van Velsor, Jason K. [Structural Integrity Associates, Inc., State College, PA (United States)

    2015-03-22

    The stated goal of this work was to develop a versatile system which could accurately measure vessel and valve internal vibrations and cavitation formation under in-service conditions in nuclear power plants, ultrasonically. The developed technology will benefit the nuclear power generation industry by allowing plant operators to monitor valve and vessel internals during operation. This will help reduce planned outages and plant component failures. During the course of this work, Structural Integrity Associates, Inc. gathered information from industry experts that target vibration amplitudes to be detected should be in the range of 0.001-in to 0.005-in (0.025-mm to 0.127-mm) and target vibration frequency ranges which should be detected were found to be between 0-Hz and 300-Hz. During the performed work, an ultrasonic measuring system was developed which utilized ultrasonic pulse-echo time-of-flight measurements to measure vibration frequency and amplitude. The developed system has been shown to be able to measure vibration amplitudes as low as 0.0008-in (0.020-mm) with vibration frequencies in the range of 17-Hz to 1000-Hz. Therefore, the developed system was able to meet the industry needs for vibration measurement. The developed ultrasonic system was also to be able to measure cavitation formation by monitoring the received ultrasonic time- and frequency-domain signals. This work also demonstrated the survivability of commercially available probes at temperatures up to 300-F for several weeks.

  8. Validation of the Oregon Scientific BPU 330 for self-monitoring of blood pressure according to the International Protocol

    Directory of Open Access Journals (Sweden)

    Li Li

    2008-10-01

    Full Text Available Li Li1, XinYu Zhang1, ChunHong Yan1, QingXiang Liang21Biomedical Engineering Lab, Faculty of Information Engineering, ShenZhen University, ShenZhen, China; 2Bao An People’s Hospital, ShenZhen, ChinaObjective: Extensive marketing of devices for self-measurement of blood pressure has created a need for purchasers to be able to satisfy themselves that such devices have been evaluated according to agreed criteria. The Oregon Scientific BPU 330 blood pressure monitor is an electronic device for upper arm measurement. This study assessed the accuracy of the Oregon Scientific BPU 330 blood pressure monitor according to the International Protocol by the Working Group on Blood Pressure Monitoring of the European Society of Hypertension for validation of blood pressure measuring devices.Method: 52 participants over 30 years of age were studied in the validation. Nine blood pressure measurements were taken alternately with a mercury sphygmomanometer by two observers, and by the supervisor, using the BPU 330 device. A total of 33 participants were selected for the analysis. The validation was divided into two phases. Phase 1 included 15 participants. If the device passed phase 1, 18 more participants were included. The 99 pairs of measurements were compared according to the International Protocol. The device was given a pass/fail recommendation based on its accuracy compared with the mercury standard (within 5, 10, and 15 mmHg, as well as the number met in the ranges specified by the International Protocol.Results: The mean and standard deviation of the difference between the mean of the observers and the BPU 330 device were 1.7 ± 4.7 mmHg and 2.8 ± 3.9 mmHg for systolic blood pressure (SBP and diastolic blood pressure (DBP, respectively. In phase 1, the device passed with a total of 33, 43, and 44 SBP readings; 38, 44, and 45 DBP readings were within 5, 10, and 15 mmHg, respectively. In phase 2.1, 81, 95, and 96 for SBP, and 83, 95, and 98 for DBP

  9. Internal Stress Monitoring of In-Service Structural Steel Members with Ultrasonic Method

    OpenAIRE

    Li, Z; He, J; Teng, J; Wang, Y

    2016-01-01

    Internal stress in structural steel members is an important parameter for steel structures in their design, construction, and service stages. However, it is hard to measure via traditional approaches. Among the existing non-destructive testing (NDT) methods, the ultrasonic method has received the most research attention. Longitudinal critically refracted (Lcr) waves, which propagate parallel to the surface of the material within an effective depth, have shown great potential as an effective s...

  10. Review of techniques for monitoring the healing fracture of bones for implementation in an internally fixated pelvis.

    Science.gov (United States)

    Wong, Lydia Chwang Yuh; Chiu, Wing Kong; Russ, Matthias; Liew, Susan

    2012-03-01

    Sacral fractures from high-impact trauma often cause instability in the pelvic ring structure. Treatment is by internal fixation which clamps the fractured edges together to promote healing. Healing could take up to 12 weeks whereby patients are bedridden to avoid hindrances to the fracture from movement or weight bearing activities. Immobility can lead to muscle degradation and longer periods of rehabilitation. The ability to determine the time at which the fracture is stable enough to allow partial weight-bearing is important to reduce hospitalisation time. This review looks into different techniques used for monitoring the fracture healing of bones which could lead to possible methods for in situ and non-invasive assessment of healing fracture in a fixated pelvis. Traditional techniques being used include radiology and CT scans but were found to be unreliable at times and very subjective in addition to being non in situ. Strain gauges have proven to be very effective for accurate assessment of fracture healing as well as stability for long bones with external fixators but may not be suitable for an internally fixated pelvis. Ultrasound provides in situ monitoring of stiffness recovery but only assesses local fracture sites close to the skin surface and has only been tested on long bones. Vibration analysis can detect non-uniform healing due to its assessment of the overall structure but may suffer from low signal-to-noise ratio due to damping. Impedance techniques have been used to assess properties of non-long bones but recent studies have only been conducted on non-biological materials and more research needs to be done before it can be applicable for monitoring healing in the fixated pelvis. Copyright © 2011 IPEM. Published by Elsevier Ltd. All rights reserved.

  11. Predicting positive mental health in internally displaced persons in Indonesia: the roles of economic improvement and exposure to violent conflict.

    Science.gov (United States)

    Saragih Turnip, Sherly; Sörbom, Dag; Hauff, Edvard

    2016-01-01

    Positive mental health, rather than just the absence of mental illness, is rarely investigated among the internally displaced persons (IDPs) affected by violent conflict in low-income countries. The purpose of this study was to investigate a model that could explain the interrelationship between factors contributing to positive mental health in displaced populations. In a longitudinal study we examine poverty, exposure to traumatic events and the change of material well-being after one year. We collec