WorldWideScience

Sample records for intercity bus lines

  1. Emission inventory estimation of an intercity bus terminal.

    Science.gov (United States)

    Qiu, Zhaowen; Li, Xiaoxia; Hao, Yanzhao; Deng, Shunxi; Gao, H Oliver

    2016-06-01

    Intercity bus terminals are hotspots of air pollution due to concentrated activities of diesel buses. In order to evaluate the bus terminals' impact on air quality, it is necessary to estimate the associated mobile emission inventories. Since the vehicles' operating condition at the bus terminal varies significantly, conventional calculation of the emissions based on average emission factors suffers the loss of accuracy. In this study, we examined a typical intercity bus terminal-the Southern City Bus Station of Xi'an, China-using a multi-scale emission model-(US EPA's MOVES model)-to quantity the vehicle emission inventory. A representative operating cycle for buses within the station is constructed. The emission inventory was then estimated using detailed inputs including vehicle ages, operating speeds, operating schedules, and operating mode distribution, as well as meteorological data (temperature and humidity). Five functional areas (bus yard, platforms, disembarking area, bus travel routes within the station, and bus entrance/exit routes) at the terminal were identified, and the bus operation cycle was established using the micro-trip cycle construction method. Results of our case study showed that switching to compressed natural gas (CNG) from diesel fuel could reduce PM2.5 and CO emissions by 85.64 and 6.21 %, respectively, in the microenvironment of the bus terminal. When CNG is used, tail pipe exhaust PM2.5 emission is significantly reduced, even less than brake wear PM2.5. The estimated bus operating cycles can also offer researchers and policy makers important information for emission evaluation in the planning and design of any typical intercity bus terminals of a similar scale.

  2. Preliminary concept for statewide intercity bus and rail transit system : priority corridor ranking and analysis.

    Science.gov (United States)

    2009-03-01

    This product summarizes the preliminary concept and priority corridors for development of a potential : statewide intercity bus and rail network. The concept is based upon the results of Tasks 1 through 5 of Texas : Department of Transportation Proje...

  3. Deregulation and Intercity Bus Operations in Florida: A Preliminary Study.

    Science.gov (United States)

    1981-03-02

    revenues have been consistent recently, but expenses have risen. The three areas most frequently served by Rabbit Bus Lines are Disney World, Sea World...Manager, Shoreline Stages had annual revenues of roughly $890,000 in 1980. In terms of trips, about ninety percent of this carrier’s traffic is interstate...this traffic constitutes the bulk of Shoreline Stage’s business by revenue , volume of traffic, and number of passengers. Charter trips to Disney

  4. Driver Performance Problems of Intercity Bus Public Transportation Safety in Indonesia

    Science.gov (United States)

    Suraji, A.; Harnen, S.; Wicaksono, A.; Djakfar, L.

    2017-11-01

    The risk of an inter-city bus public accident can be influenced by various factors such as the driver’s performance. Therefore, knowing the various influential factors related to driver’s performance is very necessary as an effort to realize road traffic safety. This study aims to determine the factors that fall on the accident associated with the driver’s performance and make mathematical modeling factors that affect the accident. Methods of data retrieval were obtained from NTSC secondary data. The data was processed by identifying factors that cause the accident. Furthermore data processing and analysis used the PCA method to obtain mathematical modeling of factors influencing the inter-city bus accidents. The results showed that the main factors that cause accidents are health, discipline, and driver competence.

  5. Life cycle cost analysis of a car, a city bus and an intercity bus powertrain for year 2005 and 2020

    International Nuclear Information System (INIS)

    Hellgren, Jonas

    2007-01-01

    The international economy, in the beginning of the 20th century, is characterized by uncertainty about the supply and the price of oil. Together with the fast decrease of electrical propulsion component prices, it becomes more and more cost effective to develop vehicles with alternative powertrains. This paper focuses on two questions: Are alternative powertrains especially cost effective for specific applications?; How does an increased fossil fuel price influences the choose of powertrain? To assess these questions, a computer tool named THEPS, developed in a Ph.D. project, is used. Three applications and three scenarios are analysed. The applications, a car, a city bus and an intercity bus, are vehicles all assumed to operate in Sweden. One scenario represents year 2005, the other two year 2020. The two future scenarios are characterized by different fossil fuel prices. The study, presented in the paper, indicates that alternative powertrains can be competitive from a cost perspective, in some applications, already in year 2005. It is for example cost effective to equip a city bus, running in countries with a high fuel price, with a hybrid powertrain. The study also indicates that pure electric, hybrid and/or fuel cell cars will probably be a more cost effective choice than conventional cars in year 2020. Another indication is that it will not be clear which powertrain concept to choose. The reason is that many cost effective powertrain concepts will be offered. The best choice will depend on the application

  6. Effect of Variation of Speed Limits on Intercity Bus Fuel Consumption, Coach and Driver Utilization, and Corporate Profitability

    Science.gov (United States)

    1975-11-01

    The effect of speed limit and passenger load on fuel consumption was determined using actual intercity buses with simulated passenger loads over different types of terrain. In addition to road tests, laboratory type measurements were made on four int...

  7. A Bilevel Programming Model to Optimize Train Operation Based on Satisfaction for an Intercity Rail Line

    Directory of Open Access Journals (Sweden)

    Zhipeng Huang

    2014-01-01

    Full Text Available The passenger travel demands for intercity rail lines fluctuate obviously during different time periods, which makes the rail departments unable to establish an even train operation scheme. This paper considers an optimization problem for train operations which respond to passenger travel demands of different periods in intercity rail lines. A satisfactory function of passenger travelling is proposed by means of analyzing the passengers’ travel choice behavior and correlative influencing factors. On this basis, the paper formulates a bilevel programming model which maximizes interests of railway enterprises and travelling satisfaction of each passenger. The trains operation in different periods can be optimized through upper layer planning of the model, while considering the passenger flow distribution problem based on the Wardrop user equilibrium principle in the lower layer planning. Then, a genetic algorithm is designed according to model features for solving the upper laying. The Frank-Wolfe algorithm is used for solving the lower layer planning. Finally, a numerical example is provided to demonstrate the application of the method proposed in this paper.

  8. Bus line classification using neural networks

    OpenAIRE

    Jiménez Alonso, Felipe; Serradilla García, Francisco; Román de Andrés, Alfonso; Naranjo Hernandez, Jose Eugenio

    2014-01-01

    Grouping urban bus routes is necessary when there are evidences of significant differences among them. In Jiménez et al. (2013), a reduced sample of routes was grouped into clusters utilizing kinematic measured data. As a further step, in this paper, the remaining urban bus routes of a city, for which no kinematic measurements are available, are classified. For such purpose we use macroscopic geographical and functional variables to describe each route, while the clustering process is perform...

  9. Benefit-cost analysis framework for evaluating inter-city transit investment.

    Science.gov (United States)

    2008-10-01

    This report describes the development and application of a benefit/cost analysis (BCA) model to support the evaluation of investment decisions for intercity bus services. The model recognizes two principle types of intercity bus benefits: benefits th...

  10. Extracting potential bus lines of Customized City Bus Service based on public transport big data

    Science.gov (United States)

    Ren, Yibin; Chen, Ge; Han, Yong; Zheng, Huangcheng

    2016-11-01

    Customized City Bus Service (CCBS) can reduce the traffic congestion and environmental pollution that caused by the increasing in private cars, effectively. This study aims to extract the potential bus lines and each line's passenger density of CCBS by mining the public transport big data. The datasets used in this study are mainly Smart Card Data (SCD) and bus GPS data of Qingdao, China, from October 11th and November 7th 2015. Firstly, we compute the temporal-origin-destination (TOD) of passengers by mining SCD and bus GPS data. Compared with the traditional OD, TOD not only has the spatial location, but also contains the trip's boarding time. Secondly, based on the traditional DBSCAN algorithm, we put forwards an algorithm, named TOD-DBSCAN, combined with the spatial-temporal features of TOD.TOD-DBSCAN is used to cluster the TOD trajectories in peak hours of all working days. Then, we define two variables P and N to describe the possibility and passenger destiny of a potential CCBS line. P is the probability of the CCBS line. And N represents the potential passenger destiny of the line. Lastly, we visualize the potential CCBS lines extracted by our procedure on the map and analyse relationship between potential CCBS lines and the urban spatial structure.

  11. Global Optimization for Bus Line Timetable Setting Problem

    Directory of Open Access Journals (Sweden)

    Qun Chen

    2014-01-01

    Full Text Available This paper defines bus timetables setting problem during each time period divided in terms of passenger flow intensity; it is supposed that passengers evenly arrive and bus runs are set evenly; the problem is to determine bus runs assignment in each time period to minimize the total waiting time of passengers on platforms if the number of the total runs is known. For such a multistage decision problem, this paper designed a dynamic programming algorithm to solve it. Global optimization procedures using dynamic programming are developed. A numerical example about bus runs assignment optimization of a single line is given to demonstrate the efficiency of the proposed methodology, showing that optimizing buses’ departure time using dynamic programming can save computational time and find the global optimal solution.

  12. SunLine Transit Agency Advanced Technology Fuel Cell Bus Evaluation: First Results Report

    Energy Technology Data Exchange (ETDEWEB)

    Eudy, L.; Chandler, K.

    2011-03-01

    This report describes operations at SunLine Transit Agency for their newest prototype fuel cell bus and five compressed natural gas (CNG) buses. In May 2010, SunLine began operating its sixth-generation hydrogen fueled bus, an Advanced Technology (AT) fuel cell bus that incorporates the latest design improvements to reduce weight and increase reliability and performance. The agency is collaborating with the U.S. Department of Energy's (DOE) National Renewable Energy Laboratory (NREL) to evaluate the bus in revenue service. This report provides the early data results and implementation experience of the AT fuel cell bus since it was placed in service.

  13. SunLine Transit Agency Advanced Technology Fuel Cell Bus Evaluation: Fourth Results Report

    Energy Technology Data Exchange (ETDEWEB)

    Eudy, L.; Chandler, K.

    2013-01-01

    SunLine Transit Agency, which provides public transit services to the Coachella Valley area of California, has demonstrated hydrogen and fuel cell bus technologies for more than 10 years. In May 2010, SunLine began demonstrating the advanced technology (AT) fuel cell bus with a hybrid electric propulsion system, fuel cell power system, and lithium-based hybrid batteries. This report describes operations at SunLine for the AT fuel cell bus and five compressed natural gas buses. The U.S. Department of Energy's National Renewable Energy Laboratory (NREL) is working with SunLine to evaluate the bus in real-world service to document the results and help determine the progress toward technology readiness. NREL has previously published three reports documenting the operation of the fuel cell bus in service. This report provides a summary of the results with a focus on the bus operation from February 2012 through November 2012.

  14. Short-term exposure to PM 10, PM 2.5, ultrafine particles and CO 2 for passengers at an intercity bus terminal

    Science.gov (United States)

    Cheng, Yu-Hsiang; Chang, Hsiao-Peng; Hsieh, Cheng-Ju

    2011-04-01

    The Taipei Bus Station is the main transportation hub for over 50 bus routes to eastern, central, and southern Taiwan. Daily traffic volume at this station is about 2500 vehicles, serving over 45,000 passengers daily. The station is a massive 24-story building housing a bus terminal, a business hotel, a shopping mall, several cinemas, offices, private residential suites, and over 900 parking spaces. However, air quality inside this bus terminal is a concern as over 2500 buses are scheduled to run daily. This study investigates the PM 10, PM 2.5, UFP and CO 2 levels inside and outside the bus terminal. All measurements were taken between February and April 2010. Measurement results show that coarse PM inside the bus terminal was resuspended by the movement of large numbers of passengers. The fine and ultrafine PM in the station concourse were from outside vehicles. Moreover, fine and ultrafine PM at waiting areas were exhausted directly from buses in the building. The CO 2 levels at waiting areas were likely elevated by bus exhaust and passengers exhaling. The PM 10, PM 2.5 and CO 2 levels at the bus terminal were lower than Taiwan's EPA suggested standards for indoor air quality. However, UFP levels at the bus terminal were significantly higher than those in the urban background by about 10 times. Therefore, the effects of UFPs on the health of passengers and workers must be addressed at this bus terminal since the levels of UFPs are higher than >1.0 × 10 5 particles cm -3.

  15. SunLine Transit Agency Advanced Technology Fuel Cell Bus Evaluation: Third Results Reports

    Energy Technology Data Exchange (ETDEWEB)

    Eudy, L.; Chandler, K.

    2012-05-01

    This report describes operations at SunLine Transit Agency for their newest prototype fuel cell bus and five compressed natural gas (CNG) buses. In May 2010, SunLine began operating its sixth-generation hydrogen fueled bus, an Advanced Technology (AT) fuel cell bus that incorporates the latest design improvements to reduce weight and increase reliability and performance. The agency is collaborating with the U.S. Department of Energy's (DOE) National Renewable Energy Laboratory (NREL) to evaluate the bus in revenue service. NREL has previously published two reports documenting the operation of the fuel cell bus in service. This report provides a summary of the results with a focus on the bus operation from July 2011 through January 2012.

  16. SunLine Transit Agency Advanced Technology Fuel Cell Bus Evaluation: Second Results Report and Appendices

    Energy Technology Data Exchange (ETDEWEB)

    Eudy, L.; Chandler, K.

    2011-10-01

    This report describes operations at SunLine Transit Agency for their newest prototype fuel cell bus and five compressed natural gas (CNG) buses. In May 2010, SunLine began operating its sixth-generation hydrogen fueled bus, an Advanced Technology (AT) fuel cell bus that incorporates the latest design improvements to reduce weight and increase reliability and performance. The agency is collaborating with the U.S. Department of Energy's (DOE) National Renewable Energy Laboratory (NREL) to evaluate the bus in revenue service. This is the second results report for the AT fuel cell bus since it was placed in service, and it focuses on the newest data analysis and lessons learned since the previous report. The appendices, referenced in the main report, provide the full background for the evaluation. They will be updated as new information is collected but will contain the original background material from the first report.

  17. 77 FR 6178 - FY 2012 Discretionary Funding Opportunities: Bus and Bus Facilities Programs (State of Good...

    Science.gov (United States)

    2012-02-07

    ... not limited to: Rail, ferry, intercity bus and private transportation providers. In order to be..., intercity bus, and private transportation providers. In order to be eligible for funding, intermodal... automobile travel, improving the pedestrian environment of a community or, use of environmental design...

  18. Conceptual design and development of a superconducting bus-line for the Large Helical Device

    International Nuclear Information System (INIS)

    Mito, T.; Takahata, K.; Yamada, S.; Yamamoto, J.; Uede, T.; Ikeda, M.

    1993-01-01

    A superconducting bus-line is proposed and preliminarily tested as an electrical feeder between the superconducting coils of the Large Helical Device (LHD) and their electrical power supply. The bus-line consists of a superconductor and its cryogenic transfer-line. The superconductor is a specially developed aluminum stabilized NbTi wire, which is installed in the innermost channel of the transfer-line. The vacuum insulated transfer-line consists of four corrugated tubes assembled coaxially. Liquid helium flows through the innermost channel and shield gas flows through another annular channel in the line. We are completing the conceptual design of the bus-line and the installation plan for the LHD experimental hall and are carrying out development of wires, including an investigation of their mechanical properties and electrical insulation. This report describes the conceptual design of the superconducting bus-line for the LHD, and the results we obtained recently during the design and development of a full-scale demonstration facility. (orig.)

  19. SunLine Transit Agency Fuel Cell Transit Bus: Fourth Evaluation Report (Report and Appendices)

    Energy Technology Data Exchange (ETDEWEB)

    Chandler, K.; Eudy, L.

    2009-01-01

    This report describes operations at SunLine Transit Agency for a prototype fuel cell bus and five new compressed natural gas (CNG) buses. This is the fourth evaluation report for this site, and it describes results and experiences from April 2008 through October 2008. These results are an addition to those provided in the previous three evaluation reports.

  20. SunLine Transit Agency Fuel Cell Transit Bus: Fifth Evaluation Report (Report and Appendices)

    Energy Technology Data Exchange (ETDEWEB)

    Eudy, L.; Chandler, K.

    2009-08-01

    This report describes operations at SunLine Transit Agency for a prototype fuel cell bus and five compressed natural gas (CNG) buses. This is the fifth evaluation report for this site, and it describes results and experiences from October 2008 through June 2009. These results are an addition to those provided in the previous four evaluation reports.

  1. A disaggregate model to predict the intercity travel demand

    Energy Technology Data Exchange (ETDEWEB)

    Damodaran, S.

    1988-01-01

    This study was directed towards developing disaggregate models to predict the intercity travel demand in Canada. A conceptual framework for the intercity travel behavior was proposed; under this framework, a nested multinomial model structure that combined mode choice and trip generation was developed. The CTS (Canadian Travel Survey) data base was used for testing the structure and to determine the viability of using this data base for intercity travel-demand prediction. Mode-choice and trip-generation models were calibrated for four modes (auto, bus, rail and air) for both business and non-business trips. The models were linked through the inclusive value variable, also referred to as the long sum of the denominator in the literature. Results of the study indicated that the structure used in this study could be applied for intercity travel-demand modeling. However, some limitations of the data base were identified. It is believed that, with some modifications, the CTS data could be used for predicting intercity travel demand. Future research can identify the factors affecting intercity travel behavior, which will facilitate collection of useful data for intercity travel prediction and policy analysis.

  2. Modeling the Equilibrium Bus Line Choice Behavior and Transit System Design with Oblivious Users

    Directory of Open Access Journals (Sweden)

    Chuan-Lin Zhao

    2014-01-01

    Full Text Available In most of transportation literature, users are assumed to be perfectly rational in minimizing their own travel costs or perceived travel costs. However, users may not be perfectly rational in implementing their choices in reality. There exists a kind of boundedly rational users, that is, oblivious users. These oblivious users make their route choices by simple criteria, for example, selecting the shortest (or the most direct route only based on physical distance or simply following routes recommended by a GPS system. This paper investigates how the existence of oblivious users affects the equilibrium bus line choice behavior in a public transit system. And we propose a method to design a more realistic system.

  3. Methodology of mixed load customized bus lines and adjustment based on time windows

    Science.gov (United States)

    Song, Rui

    2018-01-01

    Custom bus routes need to be optimized to meet the needs of a customized bus for personalized trips of different passengers. This paper introduced a customized bus routing problem in which trips for each depot are given, and each bus stop has a fixed time window within which trips should be completed. Treating a trip as a virtual stop was the first consideration in solving the school bus routing problem (SBRP). Then, the mixed load custom bus routing model was established with a time window that satisfies its requirement and the result were solved by Cplex software. Finally, a simple network diagram with three depots, four pickup stops, and five delivery stops was structured to verify the correctness of the model, and based on the actual example, the result is that all the buses ran 124.42 kilometers, the sum of kilometers was 10.35 kilometers less than before. The paths and departure times of the different busses that were provided by the model were evaluated to meet the needs of the given conditions, thus providing valuable information for actual work. PMID:29320505

  4. Potential development of an intercity passenger transit system in Texas : final project report.

    Science.gov (United States)

    2010-05-01

    This report describes the findings of a research study of the potential for development of an intercity rail and : express bus system in the state of Texas. Rather than focus on regional commuter or light rail systems : radiating from urban areas, th...

  5. Fitness to drive among commercial intercity drivers in Benin-City ...

    African Journals Online (AJOL)

    Background: Unfit drivers are prone to road traffic accident, therefore their health is paramount in ensuring the safety of road users. To determine the fitness to drive among commercial intercity bus drivers in Benin City, Edo State Material and methods: A descriptive cross-sectional study was conducted among 194 ...

  6. Intercity Travel Demand Analysis Model

    OpenAIRE

    Ming Lu; Hai Zhu; Xia Luo; Lei Lei

    2014-01-01

    It is well known that intercity travel is an important component of travel demand which belongs to short distance corridor travel. The conventional four-step method is no longer suitable for short distance corridor travel demand analysis for the time spent on urban traffic has a great impact on traveler's main mode choice. To solve this problem, the author studied the existing intercity travel demand analysis model, then improved it based on the study, and finally established a combined model...

  7. Increasing throughput of multiplexed electrical bus in pipe-lined architecture

    Science.gov (United States)

    Asaad, Sameh; Brezzo, Bernard V; Kapur, Mohit

    2014-05-27

    Techniques are disclosed for increasing the throughput of a multiplexed electrical bus by exploiting available pipeline stages of a computer or other system. For example, a method for increasing a throughput of an electrical bus that connects at least two devices in a system comprises introducing at least one signal hold stage in a signal-receiving one of the two devices, such that a maximum frequency at which the two devices are operated is not limited by a number of cycles of an operating frequency of the electrical bus needed for a signal to propagate from a signal-transmitting one of the two devices to the signal-receiving one of the two devices. Preferably, the signal hold stage introduced in the signal-receiving one of the two devices is a pipeline stage re-allocated from the signal-transmitting one of the two devices.

  8. 26 CFR 48.4221-8 - Tax-free sales of tires, tubes, and tread rubber used on intercity, local, and school buses.

    Science.gov (United States)

    2010-04-01

    ... if the bus has a passenger seating capacity of at least 20 adults and the transportation is available... of a school. Incidental use (deadheading) of the school bus without passengers to or from a point to... used on intercity, local, and school buses. 48.4221-8 Section 48.4221-8 Internal Revenue INTERNAL...

  9. Copper Heat Exchanger for the External Auxiliary Bus-Bars Routing Line in the LHC Insertion Regions

    CERN Document Server

    Garion, C; Seyvet, F; Sitko, M; Skoczen, B; Tock, J P

    2006-01-01

    The corrector magnets and the main quadrupoles of the LHC dispersion suppressors are powered by a special superconducting line (called auxiliary bus-bars line N), external to the cold mass and housed in a 50 mm diameter stainless steel tube fixed to the cold mass. As the line is periodically connected to the cold mass, the same gaseous and liquid helium cools both the magnets and the line. The final sub-cooling process (from around 4.5 K down to 1.9 K) consists in the phase transformation from liquid to superfluid helium. Heat is extracted from the line through the magnets via their point of junction. In dispersion suppressor zones, approximately 40 m long, the sub-cooling of the line is slightly delayed with respect to the magnets. This might have an impact on the readiness of the accelerator for operation. In order to accelerate the process, a special heat exchanger has been designed. It is located in the middle of the dispersion suppressor portion of the line. Its main function consists in providing a loca...

  10. Technology assessment of future intercity passenger transporation systems. Volume 2: Identification of issues affecting intercity transportation

    Science.gov (United States)

    1976-01-01

    Papers on major issues and trends that affect the future of intercity transportation are presented. Specific areas covered include: political, social, technological, institutional, and economic mechanisms, the workings of which determine how future intercity transporation technologies will evolve and be put into service; the major issues of intercity transportation from the point of view of reform, including candidate transporation technologies; and technical analysis of trends affecting the evolution of intercity transportation technologies.

  11. Intercity Travel Demand Analysis Model

    Directory of Open Access Journals (Sweden)

    Ming Lu

    2014-01-01

    Full Text Available It is well known that intercity travel is an important component of travel demand which belongs to short distance corridor travel. The conventional four-step method is no longer suitable for short distance corridor travel demand analysis for the time spent on urban traffic has a great impact on traveler's main mode choice. To solve this problem, the author studied the existing intercity travel demand analysis model, then improved it based on the study, and finally established a combined model of main mode choice and access mode choice. At last, an integrated multilevel nested logit model structure system was built. The model system includes trip generation, destination choice, and mode-route choice based on multinomial logit model, and it achieved linkage and feedback of each part through logsum variable. This model was applied in Shenzhen intercity railway passenger demand forecast in 2010 as a case study. As a result, the forecast results were consistent with the actuality. The model's correctness and feasibility were verified.

  12. Acute subdural hemorrhage while traveling by bus: a risk factor in the elderly?

    Science.gov (United States)

    Soysal, Suna; Topacoglu, Hakan; Acarbay, Sabiha; Ozbas, Kerem

    2005-01-01

    A 71-year-old man was delivered to our emergency department by an intercity bus. About 4 hours into a journey, he had complained of a headache to his wife. After one more hour, she noted a change in his level of alertness and notified the bus driver. A computed tomography scan of the head showed a subdural hemorrhage.

  13. Rationalization of Public Road Passenger Transport by Merging Bus Lines on the Example of Zadar County

    OpenAIRE

    Goran Kos; Predrag Brlek; Igor Franolić

    2012-01-01

    This study consists of the analysis of public passenger transport in Zadar County, that is, transport on the County and school lines and suggestions of transport rationalization. The rationalization comprises the application of the County and school lines integration, as well as suggestions of other measures which aim to reduce transport costs financed by Zadar County. The objectives to rationalize public passenger transport have been defined, all County transport lines of schoolchildren and ...

  14. 49 CFR 374.317 - Identification-bus and driver.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 5 2010-10-01 2010-10-01 false Identification-bus and driver. 374.317 Section 374... SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION FEDERAL MOTOR CARRIER SAFETY REGULATIONS PASSENGER CARRIER REGULATIONS Adequacy of Intercity Motor Common Carrier Passenger Service § 374.317 Identification...

  15. Rationalization of Public Road Passenger Transport by Merging Bus Lines on the Example of Zadar County

    Directory of Open Access Journals (Sweden)

    Goran Kos

    2012-07-01

    Full Text Available This study consists of the analysis of public passenger transport in Zadar County, that is, transport on the County and school lines and suggestions of transport rationalization. The rationalization comprises the application of the County and school lines integration, as well as suggestions of other measures which aim to reduce transport costs financed by Zadar County. The objectives to rationalize public passenger transport have been defined, all County transport lines of schoolchildren and other passengers have been analysed as well as actual deficiencies in the city, County and school transport needs. Road transport infrastructure, carriers and transportation vehicles have been analysed. The future transport demand has been reviewed and the prediction of passengers on lines has been provided. Within the next five to ten years no relevant changes will take place, meaning that the balance in transport supply and demand will not be disrupted significantly. This study presents the measures for transport cost reduction and increase in the safety level in the performance of public transport.

  16. Development of an on-line radon monitoring apparatus and design of the on-line radon monitoring platform based on CAN bus

    International Nuclear Information System (INIS)

    Guo Huiping; Lu Ning; Shang Aiguo; Zhou Chunlin; Chen Yingfen; Yu Hongwei

    2004-12-01

    For actual demand, an idea of 'on-line monitoring' is put forward as a way of radon monitoring, instead of traditional so called 'off-line monitoring'. In this way, the apparatus has some automatic functions such as continuous monitoring, real-time alarm; thereby, there is no need for operators' intervention in each monitoring process. With technique of hardware and software design in automation's field, the authors have successfully developed the prototype and finished the scale of it in a standard radon-chamber. This apparatus is composed of detector part and secondary-instrument. The detector part is made up of a passive diffusion collecting chamber, high voltage static electricity, semiconductor detector, charge-sensitive preamplifier and forming circuit. The secondary-instrument is actually a micro-controller system, which consists of a single-chip micro-controller cored measure-controlling unit, display unit, printing unit and alarming unit. Taking this apparatus as a cell, a 'on-line Radon Monitoring Platform' based on CAN bus has been put forward, which can realize multi-points environmental radioactivity real-time monitoring radioactivity and data process. (authors)

  17. The erigone bus study

    International Nuclear Information System (INIS)

    Durieu, L.; Vignes, M.; Wolstenholme, P.

    1982-01-01

    A study has been made of some factors determining the performance and cost-effectiveness of microcomputer bus systems implemented in Europa crates. An experimental system has been specified and a number of modules constructed in accordance with the specification, in order to test the validity of some of the ideas proposed. It has been demonstrated that the bus interfacing logic can be simple and inexpensive, while maintaining a high degree of processor independence and also a high degree of transparency in operation. The number of pins required by the bus is minimized by multiplexing address and data. A series termination for the drive of the multiplexed lines permits cross-talk to be reduced to insignificant levels: this technique is recommended for wider application. The experimental bus is proposed as a basis for the construction of simple microcomputer-based instrumentation systems. (orig.)

  18. Intercity Passenger Parametric Analysis: Overview: Maglev Analysis

    Science.gov (United States)

    1990-04-02

    This document provides information intended to clarify consideration of some of the technically-based questions which arise in connection with intercity passenger transportation, and to provide insight into the characteristics and potential roles o...

  19. The LHC SSS cold mass inside the cryostat. The complexity of the bus-bars for the power supply of the magnets and cryogenic links can be seen. The two apertures in the centre will house the beam lines

    CERN Document Server

    2003-01-01

    The LHC SSS cold mass inside the cryostat. The complexity of the bus-bars for the power supply of the magnets and cryogenic links can be seen. The two apertures in the centre will house the beam lines

  20. Air quality in inter-city buses : final report

    International Nuclear Information System (INIS)

    2005-01-01

    Various studies have suggested that air quality inside automobiles and school buses may be poorer than ambient or nearby air quality, and that concentrations of vehicle-related pollutants in city buses may be sufficiently elevated to pose concerns for vehicle occupants and operators. This paper presented the results of preliminary investigation of levels of some pollutants in inter-city buses to determine whether a fuller investigation is warranted. Another objective of the investigation was to develop methods for assessing air quality within road vehicles. Students carried monitoring equipment on 28 inter-city trips made by Greyhound Canada buses during July and August 2004. The equipment recorded average levels of carbon monoxide (CO) and nitrogen dioxide (NO 2 ), as well as concentrations of particulate matter. Bus routes were selected that allowed for an average of 10 hours of total sampling time in a day. Data was recorded on pumps, run times and routes taken. Results indicated that levels of CO in the buses were much lower than the national standard of acceptable levels for CO. Levels of NO 2 were on average lower, but 5 of the 19 recorded values exceeded acceptable levels. Average particulate levels recorded in the buses were considered acceptable, although some of the recorded levels were higher than desirable. It was concluded that further work on in-vehicle levels of NO 2 and particulate matter could be warranted. Although several procedural and equipment problems were encountered, the methods used in the investigation appeared to be valid, and were thought to be suitable for further work on in-vehicle concentrations of pollutants. 21 refs

  1. Analysis of robustness of urban bus network

    Science.gov (United States)

    Tao, Ren; Yi-Fan, Wang; Miao-Miao, Liu; Yan-Jie, Xu

    2016-02-01

    In this paper, the invulnerability and cascade failures are discussed for the urban bus network. Firstly, three static models(bus stop network, bus transfer network, and bus line network) are used to analyse the structure and invulnerability of urban bus network in order to understand the features of bus network comprehensively. Secondly, a new way is proposed to study the invulnerability of urban bus network by modelling two layered networks, i.e., the bus stop-line network and the bus line-transfer network and then the interactions between different models are analysed. Finally, by modelling a new layered network which can reflect the dynamic passenger flows, the cascade failures are discussed. Then a new load redistribution method is proposed to study the robustness of dynamic traffic. In this paper, the bus network of Shenyang City which is one of the biggest cities in China, is taken as a simulation example. In addition, some suggestions are given to improve the urban bus network and provide emergency strategies when traffic congestion occurs according to the numerical simulation results. Project supported by the National Natural Science Foundation of China (Grant Nos. 61473073, 61374178, 61104074, and 61203329), the Fundamental Research Funds for the Central Universities (Grant Nos. N130417006, L1517004), and the Program for Liaoning Excellent Talents in University (Grant No. LJQ2014028).

  2. Bus basics

    International Nuclear Information System (INIS)

    Dobinson, R.W.

    1983-01-01

    The aims of this course are: 1. To introduce the general concepts of buses used to interconnect processors, perpherals, and instrumentation. 2. To classify, albeit crudely, different types of bus systems. 3. To give some examples of past, present, and future buses as applied to the field of high-energy physics, including some details of software. 4. To provide references for further study. (orig.)

  3. Study of Intercity Travel Characteristics in Chinese Urban Agglomeration

    OpenAIRE

    Zhuoran, Li; Yan, Wang; Shichen, Zhao

    2015-01-01

    Due to rapid urban development in china, traffic problems are fast becoming considerably serious. In this study, we focus on intercity travel characteristics’ research. By investigating the travel characteristics of passengers and the intercity traffic demand forecast, we aim to discriminate the geographical spatial characteristics of departure places and to establish coupling law of city public transportation hubs and urban space which directly connect with the intercity rail station. In fut...

  4. System and prospects of China's intercity rail transit technology

    Science.gov (United States)

    Gong, Ming

    2018-06-01

    City clusters and metropolitan areas in China are flourishing in the midst of the deepening urbanization in the country, thereby resulting in the emergence of intercity rail transit. Intercity railways connect mainline and urban railways for an integrated regional transportation system that underpins and leads the development of city clusters and metropolitan areas. This study explores the development mode and service characteristics of intercity rail transit, as well as proposes overviews on this system and prospects of its future technology in China.

  5. 75 FR 16552 - High-Speed Intercity Passenger Rail (HSIPR) Program

    Science.gov (United States)

    2010-04-01

    ...; Enhancing intercity travel options; Ensuring a state of good repair of key intercity passenger rail assets... DEPARTMENT OF TRANSPORTATION Federal Railroad Administration High-Speed Intercity Passenger Rail... selections for the High-Speed Intercity Passenger Rail (HSIPR) Program. This notice builds on the program...

  6. High-speed and intercity passenger rail testing strategy.

    Science.gov (United States)

    2013-05-01

    This high-speed and intercity passenger rail (HSIPR) testing strategy addresses the requirements for testing of high-speed train sets and technology before introduction to the North American railroad system. The report documents the results of a surv...

  7. Intercity passenger rail : the congress faces critical decisions about the role of and funding for intercity passenger rail systems

    Science.gov (United States)

    2001-07-25

    With the growth in the nation's highway and aviation systems in the : previous decades, intercity passenger rail service lost its competitive edge. Highways have enabled cars to be competitive with conventional passenger trains (those operating up to...

  8. GO Bus impact analysis.

    Science.gov (United States)

    2013-08-01

    NJ TRANSIT launched two relatively new enhanced bus services: GO 25 serving the : Springfield Avenue corridor in 2008 and GO 28 serving the Bloomfield Avenue corridor in 2009. : As an enhanced but not full Bus Rapid Transit (BRT) service, GO Bus feat...

  9. Evaluation of the seat fastening in the frame of a road bus submitted to frontal impact

    Directory of Open Access Journals (Sweden)

    Márcio Walber

    Full Text Available The collective intercity transportation by bus is currently a mean of locomotion much sought after by people. Security in accidents is a very important factor that must be taken into account in design of bus body structure, being the evaluation of passenger safety of this type of vehicle is an important subject that should be checked, because in many accidents occur disconnection between seats and fastening members causing serious passengers injury, often fatal. This work aims at evaluation the behavior of frame fixing of seats of intercity bus bodies, submitted to the frontal impact situation in a rigid wall of 100% offset, through evaluation by finite element method (FEM. This study uses a numerical model corresponding to the body structure and chassis, developed through flexible beam elements, combining with shell elements for the structure of the seats and its fastening members, with the objective of not missing the essential aspects of the problem, allowing the solution with a reduced computational time. The numerical model of bus body and seat was impacted against a rigid wall at a speed of 8.89 m/s, being its validation according to the deceleration curve established by Regulation 80. Then it was gotten the Von Mises stress in fastening members of the seat structure in bus body. It is also presented a proposal to improve the fastening of the seat structure, comparing the results of the stress gotten in the two types fastening submitted to the frontal impact.

  10. Intelligent Bus Stops in the Flexible Bus Systems

    OpenAIRE

    Razi Iqbal; Muhammad Usman Ghani

    2014-01-01

    The purpose of this paper is to discuss Intelligent Bus Stops in a special Demand Responsive Transit (DRT), the Flexible Bus System. These Intelligent Bus Stops are more efficient and information rich than Traditional Bus Stops. The real time synchronization of the Flexible Bus System makes it unique as compared to Traditional Bus Systems. The Main concern is to make Bus Stops intelligent and information rich. Buses are informed about the no. of passengers waiting at the upcoming ...

  11. Land use impacts of bus rapid transit : phase II -- effects of BRT station proximity on property values along the Boston silver line Washington Street Corridor.

    Science.gov (United States)

    2012-07-01

    The development of Bus Rapid Transit (BRT) systems is relatively recent in the U.S.; however, several systems are operating and many : more are being planned. A comprehensive understanding of the relationship between land uses and BRT systems is need...

  12. New TPG bus route 28

    CERN Multimedia

    2003-01-01

    Geneva's Public Transport services (TPG) have recently inaugurated a new bus line 28, connecting the La Tour Hospital in Meyrin to the international organisations in Geneva, via the airport. All signs associated with this route will be yellow in colour. Timetables and route details can be found at http://www.tpg.ch. Relations with the Host States Service http://www.cern.ch/relations/ Tel. 72848

  13. Estimating bus passenger waiting times from incomplete bus arrivals data

    OpenAIRE

    McLeod, F.N.

    2007-01-01

    This paper considers the problem of estimating bus passenger waiting times at bus stops using incomplete bus arrivals data. This is of importance to bus operators and regulators as passenger waiting time is a key performance measure. Average waiting times are usually estimated from bus headways, that is, time gaps between buses. It is both time-consuming and expensive to measure bus arrival times manually so methods using automatic vehicle location systems are attractive; however, these syste...

  14. Intelligent Bus Stops in the Flexible Bus Systems

    Directory of Open Access Journals (Sweden)

    Razi Iqbal

    2014-09-01

    Full Text Available The purpose of this paper is to discuss Intelligent Bus Stops in a special Demand Responsive Transit (DRT, the Flexible Bus System. These Intelligent Bus Stops are more efficient and information rich than Traditional Bus Stops. The real time synchronization of the Flexible Bus System makes it unique as compared to Traditional Bus Systems. The Main concern is to make Bus Stops intelligent and information rich. Buses are informed about the no. of passengers waiting at the upcoming Bus Stops. If there are no passengers to ride or get off on upcoming Bus Stop, the Bus can skip that Bus Stop and head towards the next Bus Stop where passenger is waiting, which will decrease the ride time of the passengers on the Bus and also the wait time of the passengers waiting on the upcoming Bus Stops. Providing more information at Bus Stops about the Destination (Time to Destination, Distance to Destination etc. and Buses (Bus Location, Arrival Time of Bus etc. makes it easier for the passengers to decide whether to ride a particular Bus or not.

  15. TPG bus passes

    CERN Multimedia

    Staff Association

    2013-01-01

    The CERN Staff Association will stop selling TPG bus passes. All active and retired members of the CERN personnel will be able to purchase Unireso bus passes from the CERN Hostel - Building 39 (Meyrin site) from 1st February 2013. For more information: https://cds.cern.ch/journal/CERNBulletin/2013/04/Announcements/1505279?ln=en

  16. EVALUTION OF THE SINGLE INTERCITY FREIGHT TRANSPORTATION WAITING TIME

    Directory of Open Access Journals (Sweden)

    N. Ponomariova

    2015-07-01

    Full Text Available The example of vechicle operation on the pendulum intercity route during single freightages processing is considered. Two approaches to the definition of the single freightage waiting time by the carrier are proposed. These approaches allow to take into account the probability of the single freightage obtaining by the carrier during the different load level of the transport enterprise capacity.

  17. Pattern of Eye Diseases among Commercial Intercity Vehicle Drivers ...

    African Journals Online (AJOL)

    Objective: To determine the pattern of eye diseases among commercial intercity vehicle drivers (CIVDs) in Ilorin, Nigeria. Design: A cross-sectional descriptive study. Methodology: Out of the estimated 450 drivers operating in the five major motor parks for CIVDs in Ilorin, 399 consecutive drivers participated in the study.

  18. Viaggio Comfort - intercity coaches for the twenty-first century; Viaggio Comfort - Intercity-Reisezugwagen fuer das 21. Jahrhundert

    Energy Technology Data Exchange (ETDEWEB)

    Adam, H.D.; Simbuerger, A. [Siemens Transportation Systems, Wien (Austria); Oreski, W. [Siemens Transportation Systems, Graz (Austria)

    2008-05-15

    Modern passenger coaches for intercity trains with a top speed in the range of 230-250 km/h are creating new opportunities for travel by rail in Europe and offer an economically very attractive complement to high-speed services at speeds of more than 300 km/h. (orig.)

  19. Creative Bus Financing.

    Science.gov (United States)

    Malone, Wade

    1982-01-01

    Alternative ways of financing school bus purchases include financing privately through contractors or commercial banks, financing through sources such as insurance companies and pension funds, leasing the buses, or contracting for transportation services. (Author/MLF)

  20. SPFC bus design studies

    Energy Technology Data Exchange (ETDEWEB)

    Potter, L.; Reinkingh, J.

    1999-07-01

    This report presents the results of a study assessing the design options for a solid polymer fuel cell bus. Commercial and operation requirements, environmental and market drivers, and fuel processor modeling are examined. Power train specifications and detailed system design are investigated covering fuel cell system dynamic response, hybrid system size, fuel cell system start-up time, system specifications, and hybrid bus component dimensions and costs. (UK)

  1. Savannah River bus project

    Energy Technology Data Exchange (ETDEWEB)

    Summers, W.A. [Westinghouse Savannah River Co., Aiken, SC (United States)

    1998-08-01

    The H2Fuel Bus is the world`s first hybrid hydrogen electric transit bus. It was developed through a public/private partnership involving several leading technology and industrial organizations in the Southeast, with primary funding and program management provided by the Department of Energy. The primary goals of the project are to gain valuable information on the technical readiness and economic viability of hydrogen buses and to enhance the public awareness and acceptance of emerging hydrogen technologies. The bus has been operated by the transit agency in Augusta, Georgia since April, 1997. It employs a hybrid IC engine/battery/electric drive system, with onboard hydrogen fuel storage based on the use of metal hydrides. Initial operating results have demonstrated an overall energy efficiency (miles per Btu) of twice that of a similar diesel-fueled bus and an operating range twice that of an all-battery powered electric bus. Tailpipe emissions are negligible, with NOx less than 0.2 ppm. Permitting, liability and insurance issues were addressed on the basis of extensive risk assessment and safety analyses, with the inherent safety characteristic of metal hydride storage playing a major role in minimizing these concerns. Future plans for the bus include continued transit operation and use as a national testbed, with potential modifications to demonstrate other hydrogen technologies, including fuel cells.

  2. LHC on the bus

    CERN Multimedia

    Laëtitia Pedroso

    2010-01-01

    On 15 December, an airport bus will be transformed in the image of CERN. The bus will be seen by the thousands of travellers arriving in Geneva, informing them of the possibility to visit CERN.   Sketch of the bus. The good relationship between Geneva International Airport and CERN started several years ago. In 2004 the airport put advertising space in the arrivals area at CERN's disposal free of charge. Now, starting on 15 December, a 40-foot long bus will display a giant sticker advertisement depicting CERN as it takes passengers over the airport tarmac to their planes. This is no ordinary sticker, and it was no mean task to attach it to the bus. The task of producing and attaching it was entrusted to Geneva-based specialists Mathys SA. With the ski season opening on 15 December, there will be many travellers arriving at the airport, and the bus will be ready to receive them. When one thinks of CERN, the subjects that naturally come to mind are the LHC, the mysteries of the Universe...

  3. PyBus -- A Python Software Bus

    OpenAIRE

    Lavrijsen, W

    2005-01-01

    A software bus, just like its hardware equivalent, allows for the discovery, installation, configuration, loading, unloading, and run-time replacement of software components, as well as channeling of inter-component communication. Python, a popular open-source programming language, encourages a modular design on software written in it, but it offers little or no component functionality. However, the language and its interpreter provide sufficient hooks to implement a thin, integral layer...

  4. Air quality inside the passenger compartment of a bus.

    Science.gov (United States)

    Conceição, E Z; Silva, M C; Viegas, D X

    1997-01-01

    The indoor air quality in the passenger compartment of an intercity bus is studied. A system used for the remotion of the contaminants from the compartment, based on an extraction duct, was projected using a simple, unidimensional flow model with capability to predict the air exchange rate as a function of the vehicle velocity. Some tests using tracer gan methods were performed in a real vehicle with the contaminant remotion system mounted, in order to validate the calculation model and evaluate the performances of the system. A good agreement between the predicted and the experimental results was verified and the obtained air exchange rate was quite reasonable when compared with the former situation, without extraction duct.

  5. Intercity passenger transportation: energy efficiency and conservation case study

    Energy Technology Data Exchange (ETDEWEB)

    Khan, A.M.

    1981-01-01

    To demonstrate a methodology for energy analysis and to advance technical knowledge on the energy conservation potential in intercity passenger transportation, this paper reports findings of a case study of the Toronto-Ottawa-Montreal multimodal system. From a total (direct and indirect) energy perspective for origin-destination travel, energy efficiency and conservation potential of technological improvements, modal shifts and increased load factors are reported. 11 refs.

  6. Michigan transportation facts & figures : public transportation

    Science.gov (United States)

    2002-08-16

    This on-line document is part of a series, Transportation Facts & Figures, by the Michigan Department of Transportation (MDOT). The Public Transit section of Transportation Facts & Figures cover such topics as intercity bus service, intercity rail se...

  7. Modeling a Multinomial Logit Model of Intercity Travel Mode Choice Behavior for All Trips in Libya

    OpenAIRE

    Manssour A. Abdulsalam Bin Miskeen; Ahmed Mohamed Alhodairi; Riza Atiq Abdullah Bin O. K. Rahmat

    2013-01-01

    In the planning point of view, it is essential to have mode choice, due to the massive amount of incurred in transportation systems. The intercity travellers in Libya have distinct features, as against travellers from other countries, which includes cultural and socioeconomic factors. Consequently, the goal of this study is to recognize the behavior of intercity travel using disaggregate models, for projecting the demand of nation-level intercity travel in Libya. Multinom...

  8. Bus fuel consumption model

    Energy Technology Data Exchange (ETDEWEB)

    Zargari, S.A. [Iran Univ. of Science and Technology, Teheran (Iran, Islamic Republic of); Khan, A.M. [Carleton Univ., Ottawa, ON (Canada). Dept. of Civil and Environmental Engineering

    2000-07-01

    The interest in rapid bus transit has increased sharply with the realization that modern metropolitan areas rely on public transit to provide for strong economies and communities. As a prevention tool against traffic congestion, deteriorating air quality and rising greenhouse gas emissions, this study of bus fuel consumption was designed to assist in the planning and management of rapid bus transit. The Australian Road Research Board's (ARRB) Road Fuel Consumption Model was used as a starting point. The estimations required were realized with the help of Newtonian Mechanics. The four states of vehicular traffic were examined: acceleration, cruise, deceleration, and idle. The estimated total power required from the engine to overcome resistance forces, to run vehicle accessories and overcome internal engine friction was calculated. The data for the standard and articulated bus was obtained from OC Transpo in Ottawa. The study permitted the authors to conclude that the estimations for the parameters for power requirements and fuel consumption for heavy duty vehicles are appropriate. The methodology for the estimation of fuel consumption on the Transitway, which is part of the rapid bus transit system, proved adequate. In addition, the methodology was useful to estimate fuel savings resulting from demand management strategies with potential for modal shift. 9 refs., 6 tabs.

  9. Model Perancangan Sistem Pemesanan Tiket Bus Antar Kota Antar Propinsi Khusus di Cabang

    Directory of Open Access Journals (Sweden)

    Harijanto Pangestu

    2013-06-01

    Full Text Available At certain moments, especially on national holiday transportation users greatly increase. The manual ticket booking system of inter-city buses is not very effective and efficient as indicated that it takes long time to book tickets and find information about ticket availability for a specific purpose on a certain day. Besides, inaccuracies often happen on synchronizing ticket availability with seat availability. Due to those problems, it needs to be made a model of ticketing information system of inter-city buses. The initial phase focused on booking tickets at a branch office. The next stage of development is integrating the  information system of all branch offices to the central office. The purpose of this paper is to create a model of the system design if inter-city bus ticket reservation in inter-provincial branches can provide convenience for the branch to book tickets booked by customers. The methodology used in this research is a preliminary study by library research, followed by analysis on running systems through survey findings, then identification of information needs. From the results of this study it is found that a more specific design and implementation are expected to be made so as to provide more benefits to its users. The results of this study can be further developed and integrated with the central office.

  10. Learning NServiceBus

    CERN Document Server

    Boike, David

    2013-01-01

    This is a practical tutorial containing hands-on examples for creating a messaging and SOA based service bus.This book is for .NET developers who are looking for ways to overcome problems related to buggy third party web service integrations, codebases that have grown into a big ball of mud, and batch jobs failure.

  11. 75 FR 26839 - Metrics and Standards for Intercity Passenger Rail Service under Section 207 of the Passenger...

    Science.gov (United States)

    2010-05-12

    ... and Standards for Intercity Passenger Rail Service under Section 207 of the Passenger Rail Investment... performance and service quality of intercity passenger train operations. In compliance with the statute, the... Intercity Passenger Rail Service,'' on the FRA's Web site. Simultaneously, the FRA published a notice in the...

  12. Florida intercity high speed rail passenger service

    Energy Technology Data Exchange (ETDEWEB)

    Najafi, F.T.; Watford, S.; Moore, G.; Des, A. [Florida Univ., Gainesville, FL (United States). Dept. of Civil Engineering

    1997-10-01

    Plans for a new high-speed rail (HSR) transportation system in Florida were reviewed. HSR is believed to be the least expensive, most energy-efficient and least environmentally harmful alternative to air and highway travel. The system in Florida will be used as a case study to determine its overall impact on the environment, people and economy. The 300-plus mile system will move travelers at speeds of over 200 mph between Miami, Orlando, and Tampa. The study will identify the impacts of a HSR system on existing transportation networks, environment, energy, growth and growth distribution, safety, economy, travel time, and tourism. Transportation problems and the innovative mechanisms needed to realize the joint public and private venture approach to planning, locating, permitting, managing, financing, constructing and maintaining an inter-regional HSR line for the state were studied. The all-electric train would greatly help the environment in two ways: (1) zero emissions from the train itself, and (2) the reduction of trips by automobile and aircraft would reduce the amount of fuel and energy being used. 4 refs., 1 fig.

  13. Collaborative Optimization of Stop Schedule Plan and Ticket Allotment for the Intercity Train

    Directory of Open Access Journals (Sweden)

    Xichun Chen

    2016-01-01

    Full Text Available As regards the ticket allotment issue of the intercity passenger corridor designed for different train grades, the matching relationship between the ticket allotment and the passenger flow demand is studied. The passenger flow conversion equation which is based on the collaborative optimization of the intercity train stop schedule plan and ticket allotment is established. Then the mathematical model aiming at the maximum revenue of intercity train system and the highest satisfaction from the passengers is established. The particle swarm harmony search algorithm is designed to solve the model. The example verifies the effectiveness of the model and algorithm, which indicates that, through the collaborative optimization of the stop schedule plan and ticket allotment for different grades intercity trains, the sectional utilization rate of the train can be improved; meanwhile, the optimum matching between the intercity train revenue and the passenger satisfaction can be realized.

  14. Project survey for trolley-bus transport; Johdinautoliikenteen hankeselvitys

    Energy Technology Data Exchange (ETDEWEB)

    Anttila, T.; Eklund, P.; Airaksinen, S.; Maettoe, R.; Laehdetie, A.

    2011-04-15

    To investigate the feasibility and rationality of the revival of trolley bus traffic in Helsinki a full size project plan was conducted for a variety of alternatives. This included a survey on the latest developments of the trolley bus technology, three optional plans for route network, a budgetary level design for a fully functional depot in Koskela bus depot, examination of urban landscape structures, a study on organisational options, particular technical specifications applicable on suitable trolley buses and an examination of the impacts on the environment and on the future development of public transport. The basic concept of a trolley bus as a means of electric public transport vehicle has found its form over the years, but all the components of the system undergo at present intensive development. In context of this survey also the option of a fully autonomous electric bus powered by accumulators or fuel cells and the like was investigated. However, such technology is still totally inadequate for a heavy duty bus. There are no economically competitive and effective systems available as yet. The trolley bu is the far most reliable system and gives the best life cycle economy for a foreseeable future. Earliest estimates for alternative electric technologies in regular bus service are viable just after one investment cycle some time beyond 2030. Then it should be possible to run without the support of a comprehensive overhead line. The latest achievements in the development of trolley bus are auxiliary engine and accumulator systems allowing for more autonomous propulsion. Nowadays, trolley buses are equipped with an auxiliary power unit that alleviates the traditional restrictions of the overhead line. The modern trolley bus may run short distances without the trolley lines. Recuperation of the kinetic energy at deceleration (braking) either into the overhead line network or by storing it in the vehicle is one of the characteristics of modern trolley buses

  15. An Optimization Model for the Selection of Bus-Only Lanes in a City.

    Science.gov (United States)

    Chen, Qun

    2015-01-01

    The planning of urban bus-only lane networks is an important measure to improve bus service and bus priority. To determine the effective arrangement of bus-only lanes, a bi-level programming model for urban bus lane layout is developed in this study that considers accessibility and budget constraints. The goal of the upper-level model is to minimize the total travel time, and the lower-level model is a capacity-constrained traffic assignment model that describes the passenger flow assignment on bus lines, in which the priority sequence of the transfer times is reflected in the passengers' route-choice behaviors. Using the proposed bi-level programming model, optimal bus lines are selected from a set of candidate bus lines; thus, the corresponding bus lane network on which the selected bus lines run is determined. The solution method using a genetic algorithm in the bi-level programming model is developed, and two numerical examples are investigated to demonstrate the efficacy of the proposed model.

  16. An Optimization Model for the Selection of Bus-Only Lanes in a City.

    Directory of Open Access Journals (Sweden)

    Qun Chen

    Full Text Available The planning of urban bus-only lane networks is an important measure to improve bus service and bus priority. To determine the effective arrangement of bus-only lanes, a bi-level programming model for urban bus lane layout is developed in this study that considers accessibility and budget constraints. The goal of the upper-level model is to minimize the total travel time, and the lower-level model is a capacity-constrained traffic assignment model that describes the passenger flow assignment on bus lines, in which the priority sequence of the transfer times is reflected in the passengers' route-choice behaviors. Using the proposed bi-level programming model, optimal bus lines are selected from a set of candidate bus lines; thus, the corresponding bus lane network on which the selected bus lines run is determined. The solution method using a genetic algorithm in the bi-level programming model is developed, and two numerical examples are investigated to demonstrate the efficacy of the proposed model.

  17. Modelling Field Bus Communications in Mixed-Signal Embedded Systems

    Directory of Open Access Journals (Sweden)

    Alassir Mohamad

    2008-01-01

    Full Text Available Abstract We present a modelling platform using the SystemC-AMS language to simulate field bus communications for embedded systems. Our platform includes the model of an I/O controller IP (in this specific case an C controller that interfaces a master microprocessor with its peripherals on the field bus. Our platform shows the execution of the embedded software and its analog response on the lines of the bus. Moreover, it also takes into account the influence of the circuits's I/O by including their IBIS models in the SystemC-AMS description, as well as the bus lines imperfections. Finally, we present simulation results to validate our platform and measure the overhead introduced by SystemC-AMS over a pure digital SystemC simulation.

  18. Modelling Field Bus Communications in Mixed-Signal Embedded Systems

    Directory of Open Access Journals (Sweden)

    Patrick Garda

    2008-08-01

    Full Text Available We present a modelling platform using the SystemC-AMS language to simulate field bus communications for embedded systems. Our platform includes the model of an I/O controller IP (in this specific case an I2C controller that interfaces a master microprocessor with its peripherals on the field bus. Our platform shows the execution of the embedded software and its analog response on the lines of the bus. Moreover, it also takes into account the influence of the circuits's I/O by including their IBIS models in the SystemC-AMS description, as well as the bus lines imperfections. Finally, we present simulation results to validate our platform and measure the overhead introduced by SystemC-AMS over a pure digital SystemC simulation.

  19. Analysing passenger arrivals rates and waiting time at bus stops

    OpenAIRE

    Kaparias, I.; Rossetti, C.; Trozzi, V.

    2015-01-01

    The present study investigates the rather under-explored topic of passenger waiting times at public transport facilities. Using data collected from part of London’s bus network by means of physical counts, measurements and observations, and complemented by on-site passenger interviews, the waiting behaviour is analysed for a number of bus stops served by different numbers of lines. The analysis employs a wide range of statistical methods and tools, and concentrates on three aspects: passenger...

  20. Circuit breaker and bus

    International Nuclear Information System (INIS)

    Vogel, H.F.

    1978-01-01

    Two close-open operations are required each pulse cycle at approximately 3 MA with the breaker in series with the burn supply, both forming a leg in parallel with the E-coil and the homopolar. To conduct the 3-MA current, approximately 30 breaker units are connected in parallel. Each unit is equipped with a counterpulse capacitor bank, and the bus for the 30 units is provided with a common saturable reactor core made of strip steel wound around the bus. Oil breakers of a special design are chosen because of their high arc resistance facilitating the current transfer to the homopolar machine and for obtaining precision timing in opening and closing of the contacts. The precision timing is achieved by a shock wave method with the oil serving as hydraulic medium. Each of the parallel breaker units possesses two sets of contacts, a stationary and a transient one. A 1-mΩ resistor in series with the transient contacts of each breaker unit is to improve the current sharing. The bus consists of room temperature copper, stranded and transposed to help provide current equalization under transient conditions

  1. Miniature JPL Universal Instrument Bus

    Data.gov (United States)

    National Aeronautics and Space Administration — Develop a Universal Digital Processor Bus architecture using state of the art commercial packaging technologies. This work will transition commercial advanced- yet...

  2. A PRACTICAL STUDY ON APPLICABILITY OF THE INCENTIVE SUBSIDY TO BUS NETWORK IN KUMAMOTO CITY

    Science.gov (United States)

    Mizokami, Shoshi; Fujimi, Toshio; Hirano, Toshihiko

    Recently, the number of passenger of public bus services in Japan tends to decrease due to the motorization. This condition leads to a severe management situation, including in Kumamoto City. Since 1984, the deficit of bus companies operation in provision of bus services in Kumamoto has been covered by Kumamoto City Government on the basis of lines subsidy, and the city allocated a number of subsidy of about 200 million yen in 2007. Currently, The Kumamoto city government plans to reduce the amount of subsidy to bus companies by introducing the giving of incentive to bus companies in order to trim bus company deficit. This study aims to construct the mathematical model of the incentive reward and apply the model to realignment of buses lines networks in Kumamoto Metropolitan Area.

  3. Learning NServiceBus Sagas

    CERN Document Server

    Helton, Rich

    2015-01-01

    If you are an Enterprise C# developer who wishes to extend your knowledge of NServiceBus and Enterprise Service Bus in C#, this is the book for you. This book is designed to enhance the education of ESBs and their messaging, whether you are a beginner or a seasoned expert in Enterprise C#, Apex, and Visualforce pages.

  4. Modeling Intercity Mode Choice and Airport Choice in the United States

    OpenAIRE

    Ashiabor, Senanu Y.

    2007-01-01

    The aim of this study was to develop a framework to model travel choice behavior in order to estimate intercity travel demand at nation-level in the United States. Nested and mixed logit models were developed to study national-level intercity transportation in the United States. A separate General Aviation airport choice model to estimates General Aviation person-trips and number of aircraft operations though more than 3000 airports was also developed. The combination of the General Aviati...

  5. Application of the Expanded Theory of Planned Behavior in Intercity Travel Behavior

    OpenAIRE

    Peng, Jing; Zhi-cai, Juan; Lin-jie, Gao

    2014-01-01

    Congestion in intercity corridors of metropolitan area has been increasing steadily. To alleviate congestion, many major investment projects, such as the high speed railway projects, were proposed by agency. To evaluate the adequacy and efficiency of these projects, the intercity travel behavior should be analyzed in metropolitan area. The paper constructed a Multiple Indicators and Multiple Causes (MIMIC) model according to an expanded theory of planned behavior (TPB) to study the travel beh...

  6. Evaluating Opportunities to Enhance Hoosier State Train Ridership through a Survey of Riders’ Opinions and an Assessment of Access to the Line

    Science.gov (United States)

    2017-12-01

    Passenger rail is an integral part of intercity transportation networks, especially in areas where residents do not have access to a car or there are not any other options for intercity travel. The Hoosier State Train (HST) line connects five station...

  7. Natural gas powered bus

    International Nuclear Information System (INIS)

    Ambuehl, D.; Fernandez, J.

    2003-01-01

    This report for the Swiss Federal Office of Energy presents the results of a project carried out by the Swiss Federal Institute of Technology in Zurich to evaluate the performance of a natural-gas-powered bus in comparison with two diesel buses. The report provides details on the vehicles, their routes and the results of interviews made with both passengers and drivers. Details of measurements made on fuel consumption and pollutant emissions are presented in tabular and graphical form, as are those made on noise emissions inside and outside the vehicles. The conclusions of the project are presented including economic aspects of using gas as a motor fuel. Also, the views of passengers, who were more concerned with comfort aspects, and drivers, who were more interested in technical aspects, are quoted

  8. Hybrid Electric Transit Bus

    Science.gov (United States)

    Viterna, Larry A.

    1997-01-01

    A government, industry, and university cooperative is developing an advanced hybrid electric city transit bus. Goals of this effort include doubling the fuel economy compared to current buses and reducing emissions to one-tenth of current EPA standards. Unique aspects of the vehicle's power system include the use of ultra-capacitors as an energy storage system, and a planned natural gas fueled turbogenerator developed from a small jet engine. Power from both the generator and energy storage system is provided to a variable speed electric motor attached to the rear axle. At over 15000 kg gross weight, this is the largest vehicle of its kind ever built using ultra-capacitor energy storage. This paper describes the overall power system architecture, the evolution of the control strategy, and its performance over industry standard drive cycles.

  9. Terminals for Suburb Bus Transport in Bratislava

    Science.gov (United States)

    Schlosser, Tibor; Schlosser, Peter; Cápayová, Silvia; Hodáková, Dominika

    2017-10-01

    The main objective of this article is to describe the strategy for development of the public transport terminals in the city of Bratislava, Capital of Slovak Republic. The reason goes from the private operator Slovak Lines, who operates the suburb bus transport in the agglomeration of the city. For this operator was created a transport model, while placing emphasis on optimizing the compliance of suburban public transport with urban public transport in the city of Bratislava and evaluating the significance of the new Bus Station to be constructed at Mlynské Nivy - in a new down town centre of the city. The main issue is to ensure the best available offer of public transport (PT) to passengers in the Bratislava agglomeration. The subject of the study was oriented to specify and propose changes in the transport infrastructure and integrated public transport organisation on the area of the city in terms of the significant position of the new Mlynské Nivy Bus Station (MN BS), which is under preparation with realization in the year 2017.

  10. 76 FR 37184 - Discretionary Bus and Bus Facilities Program

    Science.gov (United States)

    2011-06-24

    ... transporting bicycles on public transportation vehicles. The FY 2011 Appropriations Act allows a 90 percent Federal share for the total cost of a biodiesel bus. The Act also allows a 90 percent Federal share for...

  11. American Fuel Cell Bus Project Evaluation. Second Report

    Energy Technology Data Exchange (ETDEWEB)

    Eudy, Leslie [National Renewable Energy Lab. (NREL), Golden, CO (United States); Post, Matthew [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2015-09-01

    This report presents results of the American Fuel Cell Bus (AFCB) Project, a demonstration of fuel cell electric buses operating in the Coachella Valley area of California. The prototype AFCB was developed as part of the Federal Transit Administration's (FTA's) National Fuel Cell Bus Program. Through the non-profit consortia CALSTART, a team led by SunLine Transit Agency and BAE Systems developed a new fuel cell electric bus for demonstration. SunLine added two more AFCBs to its fleet in 2014 and another in 2015. FTA and the AFCB project team are collaborating with the U.S. Department of Energy (DOE) and DOE's National Renewable Energy Laboratory to evaluate the buses in revenue service. This report summarizes the performance results for the buses through June 2015.

  12. Air-pollution and economics: diesel bus versus electric bus

    OpenAIRE

    Adheesh, SR; Vasisht, Shravanth M; Ramasesha, Sheela K

    2016-01-01

    The Bangalore Metropolitan Transport Corporation (BMTC) took an initiative to check the overall benefits of introducing electric buses as a suitable replacement for the diesel buses to tackle the burgeoning pollution in the city of Bengaluru, India. For a trial run of three months, an electric bus was procured from a Chinese company `Build Your Dreams' (BYD). Data were collected by BMTC on the operation and maintenance of the bus. This new initiative, if rightly guided, could have a direct im...

  13. IMPACTS OF BUS STOP IMPROVEMENTS

    Science.gov (United States)

    2018-03-23

    Improving bus stops by providing shelters, seating, signage, and sidewalks is relatively inexpensive and popular among riders and local officials. Making such improvements, however, is not often a priority for U.S. transit providers because of compet...

  14. Scaling Laws in Chennai Bus Network

    OpenAIRE

    Chatterjee, Atanu; Ramadurai, Gitakrishnan

    2015-01-01

    In this paper, we study the structural properties of the complex bus network of Chennai. We formulate this extensive network structure by identifying each bus stop as a node, and a bus which stops at any two adjacent bus stops as an edge connecting the nodes. Rigorous statistical analysis of this data shows that the Chennai bus network displays small-world properties and a scale-free degree distribution with the power-law exponent, $\\gamma > 3$.

  15. Staying Safe in the Car and on the Bus

    Science.gov (United States)

    ... a booster! Get in the Back Here's another important safety rule: Sit in the back seat. Kids 12 ... or band concerts once in a while, it's important to follow these rules. When you see the bus driving up, everyone waiting should get into a line. ...

  16. Superconducting link bus design for the accelerator project for upgrade of LHC

    International Nuclear Information System (INIS)

    Nobrega, F.; Brandt, J.; Cheban, S.; Feher, S.; Kaducak, M.; Kashikhin, V.; Peterson, T.

    2011-01-01

    The Accelerator Project for Upgrade of LHC (APUL) is a U.S. project participating in and contributing to CERN's Large Hadron Collider (LHC) upgrade program. Fermi National Accelerator Laboratory in collaboration with Brookhaven National Laboratory was developing sub-systems for the upgrade of the LHC final focus magnet systems. Part of the upgrade called for various lengths of superconducting power transmission lines known as SC Links which were up to 100 m long. The SC Link electrically connects the current leads in the Distribution Feed Boxes to the interaction region magnets. The SC Link is an extension of the magnet bus housed within a cryostat. The present concept for the bus consists of 22 power cables, 4 x 13 kA, 2 x 7 kA, 8 x 2.5 kA and 8 x 0.6 kA bundled into one bus. Different cable and strand possibilities were considered for the bus design including Rutherford cable. The Rutherford cable bus design potentially would have required splices at each sharp elbow in the SC Link. The advantage of the round bus design is that splices are only required at each end of the bus during installation at CERN. The round bus is very flexible and is suitable for pulling through the cryostat. Development of the round bus prototype and of 2 splice designs is described in this paper. Magnetic analysis and mechanical test results of the 13 kA cable and splices are presented.

  17. Bus systems in motor vehicles; Bussysteme im Kfz

    Energy Technology Data Exchange (ETDEWEB)

    Schule, Roland

    2008-07-01

    There is hardly any modern vehicle without a bus system. This interactive learning software explains why electric and electronic systems in motor vehicles should be linked and uses various bus types to illustrate the various alternatives, bus structures, and data types. The physical side of bus systems is gone into, the data structure is explained, and the various bus typologies are outlined. From the fundamentals of bus systems, the software proceeds to present the most important bus systems and their main properties. Subjects: Diagnosis bus, LIN bus, CAN bus, MOST bus, Bluetooth. The bus systems EIA-485, LVDS, D{sup 2}B, byteflight, and Flexray are briefly characterised. (orig.)

  18. The U.S. Rural Population and Scheduled Intercity Transportation in 2010 : A Five-Year Decline in Transportation Access.

    Science.gov (United States)

    2011-02-01

    Between 2005 and 2010, 3.5 million rural residents lost access to scheduled intercity transportation, increasing the percent of rural residents without access to intercity transportation from 7 to 11 percent. In 2005, 5.4 million rural residents lack...

  19. Fuel cell bus operation, system investigation H2 bus

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    The WP covers two tasks: - Prepartion of Technical Catalogue: In cooperation with ICIL, AR have compiled a technical catalogue, providing the impartial descriptions, both of existing technology and regulations, and the likely future developments of these, as to remedy the first problem faced by a potential hydrogen bus fleet operator viz the absence of an impartial description of the available vehicle and fuels systems together with the absence of a description of regulatory and safety factors which need consideration. - Fuel Cell Bus Operation - System Investigation H 2 Bus: The application of fuel cell electric generation systems to hybrid electrical buses or electrical busses without any storage system on board is considered. The task will cover safety and environmental aspects, a cost estimate and a market evaluation. (orig.)

  20. Modal shifts in short-haul passenger travel and the consequent energy impacts. [Intercity travel under 500 miles

    Energy Technology Data Exchange (ETDEWEB)

    1980-03-01

    A study was performed to evaluate the impacts of strategies to effect modal shifts in short-haul passenger travel (defined herein as intercity travel under 500 miles) from energy-intensive modes to those modes that are less energy-intensive. A series of individual strategies, ranging from incentives to the less energy-intensive modes (bus, rail) to penalties to the more energy-intensive modes (auto, air) was examined to determine energy saved and policy implications relative to strategy implementation. The most effective of the individual strategies were then combined in all permutations, and the analysis was repeated. As part of the analytical process, effects of factors other than energy (user cost and time, emissions, government subsidy, and travel fatailities) were examined in a benefit/cost analysis. Finally, energy savings, benefit/cost impacts, implementation considerations, and policy implications were evaluated to arrive at conclusions as to the effectiveness of the more-influential strategies and to the overall effectiveness of induced modal shifts. The principal conclusion of the study is that the maximum 1980 energy saving that might be realized by modal shifts, discounting the concurrent effects of demand suppression and improvement of mode efficiency, is approximately 83 x 10/sup 12/ Btu (46,500 bbl gasoline per day), 3.8% of the total projected 1980 energy consumption in the short-haul transportation sector and 0.23% of the total US petroleum use. It was also concluded that strategies to achieve these small savings by modal shifts would result in significant economic, social, and business disruptions.

  1. RS-485 Bus Design of a Missile Simulation Training System

    Directory of Open Access Journals (Sweden)

    Liu Fang

    2013-07-01

    Full Text Available In a missile simulation training system with one-master and multi-slaves distributed system structure, a universal controller is necessary due to the system composed with several controllers. In this research, the designed controllers communicate with each other and upper control computer through RS-485 field bus. RS-485 bus including interface circuits, transmission protocol, Cyclic Redundancy Check (CRC method and upper control test software is designed and proposed. The universal controller adopting the designed RS-485 interface circuits is connected through twisted-pair and makes the simulation system, then the controller is tested in line. The results show that the RS-485 bus communicates effectively using the protocol and CRC method, data transmission rates reaches 115.2 kbps, and has a good stability.

  2. Technology assessment of future intercity passenger transportation systems. Volume 7: Study recommendations

    Science.gov (United States)

    1976-01-01

    Research and analysis tasks to alleviate negative impacts, to augment positive impacts, or to better understand the impacts produced by the potential introduction of the alternate transportation technologies are identified. The project team's recommendations on research and analysis efforts which have resulted from the technology assessment are provided. Many of the recommendations apply to the future supply of intercity passenger transportation services, categorized by mode. Other recommendations pertain to broad issues in intercity transportation--e.g., finance, regulation, traveler values--that will affect all modes.

  3. Made of modules - the Setra versatile bus; Aus Modulen kombiniert - die Baureihe Setra-Kombibus

    Energy Technology Data Exchange (ETDEWEB)

    Hamsten, B.; Stangl, G. [EvoBus GmbH, Stuttgart (Germany)

    1997-07-01

    Setra is in the process of replacing its most successful bus 200 UL which, with its many versions, was for more than ten years leader in the market saegment of intercity public service buses. The development of the new bus family, the `Kombibus` Kombi means versatile, was started from scratch. The entirely new bus is made from modules, and the consistency with which this idea was carried through is the real innovation. Not only are driveline and running gear standardised modules - this has been common practice with buses for a long time - but also the body in white, the components and fittings of the body, the equipment, and the many extras. With only four different cross sections through the passenger compartment a wide spectrum of buses is covered, ranging from a plain low-floor bus to the luxurious travel coach. The `Kombibus` permits the operator of a bus fleet to combine modules to make exactly the bus he requires without the need for a new type. At the same time, the manufacturer has gained the advantage of being able to serve a larger market segment with fewer parts and components, at lower cost and with a shorter delivery time. (orig.) [Deutsch] Setra ist dabei, die erfolgreiche Baureihe 200, die seit mehr als zehn Jahren Markftuehrer in dem Segment Ueberlandlinienbus ist, durch die von Grund auf neu entwickelte Familie `Kombibus` abzuloesen. Innovativ am `Kombibus` ist die Konsequenz, mit der das Modulkonzept auf alle Komponenten angewendet wurde. Nicht nur Triebstrang und Fahrwerk wurden danach festgelegt, sondern auch die Karosserie, ihr Rohbau ebenso wie ihre Ausruestung und das gesamte Zubehoer. Mit nur vier verschiedenen Querschnittsformen durch den Fahrgastraum wird ein Spektrum abgedeckt, welches vom nuechternen Niederflur- bis hin zum komfortablen Reisebus reicht. Den Betreibern von Omnibussen bietet der `Kombibus` die Moeglichkeit, sich den genau auf ihre Anforderungen zugeschnittenen Bus zusammenzustellen. Fuer den Hersteller ergibt sich der

  4. San Antonio's 1983 Bus Passenger Survey

    Science.gov (United States)

    1983-10-01

    Many transit operators routinely collect ridership data in order to provide a : basis for the planning of bus services. Often a survey is conducted of bus : riders to determine their riding habits, their views about the quality of : current service, ...

  5. School Bus Accidents and Driver Age.

    Science.gov (United States)

    McMichael, Judith

    The study examines the rates and types of school bus accidents according to the age of the school bus driver. Accident rates in North Carolina for the school year 1971-72 were analyzed using three sources of data: accident reports, driver and mileage data, and questionnaires administered to a sample of school bus drivers. Data were obtained on…

  6. Application of the Expanded Theory of Planned Behavior in Intercity Travel Behavior

    Directory of Open Access Journals (Sweden)

    Jing Peng

    2014-01-01

    Full Text Available Congestion in intercity corridors of metropolitan area has been increasing steadily. To alleviate congestion, many major investment projects, such as the high speed railway projects, were proposed by agency. To evaluate the adequacy and efficiency of these projects, the intercity travel behavior should be analyzed in metropolitan area. The paper constructed a Multiple Indicators and Multiple Causes (MIMIC model according to an expanded theory of planned behavior (TPB to study the travel behavior of choosing from the choice set of the traditional train, the high speed railway and the coach by demographic and psychological factors. Through empirical data collection and analysis, we found that demographic factors of travelers indeed positively engender the latent variables in MIMIC, and descriptive norm and habit had direct or indirect significant effect on travel behavior and intention. On the basis of the effect of psychological constructors of the expanded TPB on the intercity travel behavior and differentiation of traveler's demographic characteristics, the agency can make reasonable policies and proper information for the intercity transportation. The results will support the basic theory of optimizing the transportation system in metropolitan area. Implications for researchers and suggestions for future research are also addressed in this study.

  7. 49 CFR 37.91 - Wheelchair locations and food service on intercity rail trains.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 1 2010-10-01 2010-10-01 false Wheelchair locations and food service on intercity rail trains. 37.91 Section 37.91 Transportation Office of the Secretary of Transportation TRANSPORTATION SERVICES FOR INDIVIDUALS WITH DISABILITIES (ADA) Acquisition of Accessible Vehicles By Public Entities § 37.91 Wheelchair locations and food...

  8. 76 FR 14443 - High-Speed Intercity Passenger Rail (HSIPR) Program

    Science.gov (United States)

    2011-03-16

    ... agreement. 3.4 Eligible Projects 3.4.1 Definition of Capital Projects Capital projects are defined by 49 U.S... the project's financing; Encouragement of the implementation of positive train control (PTC...: Notice of funding availability for high-speed and intercity passenger rail projects. SUMMARY: This notice...

  9. Optimizing Tailored Bus Bridging Paths

    NARCIS (Netherlands)

    Gu, Wei; Yu, Jie; Ji, Yuxiong; van der Gun, J.P.T.; Pel, A.J.; Zhang, H. Michael; van Arem, B.

    2017-01-01

    Metro disruptions due to unexpected events reduce transit system reliability, resulting in significant productivity loss and long passenger delays. Bus bridging strategy is often used to connect stations affected by metro disruptions such that passengers could continue their journey. The literature

  10. Bus transport in Greater Manchester

    DEFF Research Database (Denmark)

    Sørensen, Claus Hedegaard; Gudmundsson, Henrik

    component regards the organisation of public bus transport at the local level. This involves the deregulation and privatisation reforms introduced by the Conservative Government from 1986 onwards, as well as the ‘partnerships’ and other new instruments introduced by the Labour Government in the Transport...

  11. Pybus - A Python Software Bus

    International Nuclear Information System (INIS)

    Lavrijsen, Wim T.L.P.

    2004-01-01

    A software bus, just like its hardware equivalent, allows for the discovery, installation, configuration, loading, unloading, and run-time replacement of software components, as well as channeling of inter-component communication. Python, a popular open-source programming language, encourages a modular design on software written in it, but it offers little or no component functionality. However, the language and its interpreter provide sufficient hooks to implement a thin, integral layer of component support. This functionality can be presented to the developer in the form of a module, making it very easy to use. This paper describes a Pythonmodule, PyBus, with which the concept of a ''software bus'' can be realized in Python. It demonstrates, within the context of the ATLAS software framework Athena, how PyBus can be used for the installation and (run-time) configuration of software, not necessarily Python modules, from a Python application in a way that is transparent to the end-user

  12. Electrical system architecture having high voltage bus

    Science.gov (United States)

    Hoff, Brian Douglas [East Peoria, IL; Akasam, Sivaprasad [Peoria, IL

    2011-03-22

    An electrical system architecture is disclosed. The architecture has a power source configured to generate a first power, and a first bus configured to receive the first power from the power source. The architecture also has a converter configured to receive the first power from the first bus and convert the first power to a second power, wherein a voltage of the second power is greater than a voltage of the first power, and a second bus configured to receive the second power from the converter. The architecture further has a power storage device configured to receive the second power from the second bus and deliver the second power to the second bus, a propulsion motor configured to receive the second power from the second bus, and an accessory motor configured to receive the second power from the second bus.

  13. A descriptive study on public transport user behaviour from Live Bus Arrivals

    OpenAIRE

    Dell’Amico, M.; Hadjidimitriou, S.; Kaparias, I.

    2014-01-01

    In order to offer public transport that meet citizens’ needs for transport and further increase the use of bus services, Public Authorities need to analyse and understand travellers behaviour. Automatic Vehicle Location (AVL) data provide information on the observed time of arrival and departure of a bus at each stop. These data are fed into an algorithm to provide information to users on the expected time of arrival at the bus stop by an on-line service. In the city of London this service is...

  14. Avionic Data Bus Integration Technology

    Science.gov (United States)

    1991-12-01

    address the hardware-software interaction between a digital data bus and an avionic system. Very Large Scale Integration (VLSI) ICs and multiversion ...the SCP. In 1984, the Sperry Corporation developed a fault tolerant system which employed multiversion programming, voting, and monitoring for error... MULTIVERSION PROGRAMMING. N-version programming. 226 N-VERSION PROGRAMMING. The independent coding of a number, N, of redundant computer programs that

  15. Mode shift strategies in intercity transportation and their effect on energy consumption

    Science.gov (United States)

    Sokolsky, S.

    1975-01-01

    Policies are examined which, if implemented, could lead to significant energy savings in intercity travel in the northeast corridor arena, without restricting the traveler's freedom of mode choice. The effects on arena energy consumption of introducing new, more energy-efficient aircraft are investigated; and several strategies unrelated to the implementation of new aircraft are introduced to yield reductions in overall intercity energy use. In both parts of this analysis, resulting changes in patronage (modal share) and energy use are demonstrated, leading to new insights into the effectiveness of different potential policies for achieving energy conservation. Some observations on induced demand trends that could be associated with certain strategies and the resultant potential effect on energy conservation are provided.

  16. MEASURING CAR DRIVERS’ WILLINGNESS TO PAY FOR IMPROVED INTERCITY TRANSPORTATION SERVICE: A CASE STUDY IN LIBYA

    Directory of Open Access Journals (Sweden)

    MANSSOUR A. ABDULASALM MISKEEN

    2016-08-01

    Full Text Available The current study investigates solutions to optimize the intercity highway network and to facilitate the understanding of the transport mode of Libyans, according to the proposed transport policies, in terms of reducing car usage for intercity trips. In this study, different models namely the logit and spike models are applied to estimate the mean of the willingness to pay (WTP value for some proposed policies in order to be able to compare the results from each policy and analyses to what extent that each was regarded as suitable for our data characteristics. A large number of respondents were unwilling to pay any money for the different proposed policies on transportation. Therefore, the Spike model was used to avoid errors in estimation and create a WTP pricing model for the different proposed policies on transportation. The overall results indicate that the spike model outperforms the logit model significantly.

  17. Proceedings of the 1st International Workshop on High-Speed and Intercity Railways

    CERN Document Server

    Ye, Xiao-Wei

    2012-01-01

    This book contains the papers included in the proceedings of the 1st International Workshop on High-speed and Intercity Railways (IWHIR 2011) held in Shenzhen and Hong Kong, China from July 19 to July 22, 2011, which is organized by The Hong Kong Polytechnic University, in collaboration with Southwest Jiaotong University, Beijing Jiaotong University, Dalian Jiaotong University, China Engineering Consultants, Inc., Zhejiang University, and Tsinghua University. Continuing the great initiatives and momentums of the rapid development in high-speed and intercity railways worldwide in recent years, IWHIR 2011 aims at providing a platform for academic scholars and practicing engineers to share knowledge and experience, to promote collaboration, and to strengthen R&D activities related to railway engineering. Engineers, scientists, professors, and students from universities, research institutes, and related industrial companies have been cordially invited to participate in the workshop. These papers have covered ...

  18. LINES

    Directory of Open Access Journals (Sweden)

    Minas Bakalchev

    2015-10-01

    Full Text Available The perception of elements in a system often creates their interdependence, interconditionality, and suppression. The lines from a basic geometrical element have become the model of a reductive world based on isolation according to certain criteria such as function, structure, and social organization. Their traces are experienced in the contemporary world as fragments or ruins of a system of domination of an assumed hierarchical unity. How can one release oneself from such dependence or determinism? How can the lines become less “systematic” and forms more autonomous, and less reductive? How is a form released from modernistic determinism on the new controversial ground? How can these elements or forms of representation become forms of action in the present complex world? In this paper, the meaning of lines through the ideas of Le Corbusier, Leonidov, Picasso, and Hitchcock is presented. Spatial research was made through a series of examples arising from the projects of the architectural studio “Residential Transformations”, which was a backbone for mapping the possibilities ranging from playfulness to exactness, as tactics of transformation in the different contexts of the contemporary world.

  19. National fuel cell bus program : proterra fuel cell hybrid bus report, Columbia demonstration.

    Science.gov (United States)

    2011-10-01

    This report summarizes the experience and early results from a fuel cell bus demonstration funded by the Federal Transit Administration (FTA) under the National Fuel Cell Bus Program. A team led by the Center for Transportation and the Environment an...

  20. Bus Route Design with a Bayesian Network Analysis of Bus Service Revenues

    OpenAIRE

    Liu, Yi; Jia, Yuanhua; Feng, Xuesong; Wu, Jiang

    2018-01-01

    A Bayesian network is used to estimate revenues of bus services in consideration of the effect of bus travel demands, passenger transport distances, and so on. In this research, the area X in Beijing has been selected as the study area because of its relatively high bus travel demand and, on the contrary, unsatisfactory bus services. It is suggested that the proposed Bayesian network approach is able to rationally predict the probabilities of different revenues of various route services, from...

  1. GIS based analysis of Intercity Fatal Road Traffic Accidents in Iran.

    Science.gov (United States)

    Alizadeh, A; Zare, M; Darparesh, M; Mohseni, S; Soleimani-Ahmadi, M

    2015-01-01

    Road traffic accidents including intercity car traffic accidents (ICTAs) are among the most important causes of morbidity and mortality due to the growing number of vehicles, risky behaviors, and changes in lifestyle of the general population. A sound knowledge of the geographical distribution of car traffic accidents can be considered as an approach towards the accident causation and it can be used as an administrative tool in allocating the sources for traffic accidents prevention. This study was conducted to investigate the geographical distribution and the time trend of fatal intercity car traffic accidents in Iran. To conduct this descriptive study, all Iranian intercity road traffic mortality data were obtained from the Police reports in the Statistical Yearbook of the Governor's Budget and Planning. The obtained data were for 17 complete Iranian calendar years from March 1997 to March 2012. The incidence rate (IR) of fatal ICTAs for each year was calculated as the total number of fatal ICTAs in every 100000 population in specified time intervals. Figures and maps indicating the trends and geographical distribution of fatal ICTAs were prepared while using Microsoft Excel and ArcGis9.2 software. The number of fatal car accidents showed a general increasing trend from 3000 in 1996 to 13500 in 2012. The incidence of fatal intercity car accidents has changed from six in 100000 population in 1996 to 18 in 100000 population in 2012. GIS based data showed that the incidence rate of ICTAs in different provinces of Iran was very divergent. The highest incidence of fatal ICTAs was in Semnan province (IR= 35.2), followed by North Khorasan (IR=22.7), and South Khorasan (IR=22). The least incidence of fatal ICTAs was in Tehran province (IR=2.4) followed by Khozestan (IR=6.5), and Eastern Azarbayejan (IR=6.6). The compensation cost of fatal ICTAs also showed an increasing trend during the studied period. Since an increasing amount of money was being paid yearly for the car

  2. GIS based analysis of Intercity Fatal Road Traffic Accidents in Iran

    Science.gov (United States)

    Alizadeh, A; Zare, M; Darparesh, M; Mohseni, S; Soleimani-Ahmadi, M

    2015-01-01

    Road traffic accidents including intercity car traffic accidents (ICTAs) are among the most important causes of morbidity and mortality due to the growing number of vehicles, risky behaviors, and changes in lifestyle of the general population. A sound knowledge of the geographical distribution of car traffic accidents can be considered as an approach towards the accident causation and it can be used as an administrative tool in allocating the sources for traffic accidents prevention. This study was conducted to investigate the geographical distribution and the time trend of fatal intercity car traffic accidents in Iran. To conduct this descriptive study, all Iranian intercity road traffic mortality data were obtained from the Police reports in the Statistical Yearbook of the Governor’s Budget and Planning. The obtained data were for 17 complete Iranian calendar years from March 1997 to March 2012. The incidence rate (IR) of fatal ICTAs for each year was calculated as the total number of fatal ICTAs in every 100000 population in specified time intervals. Figures and maps indicating the trends and geographical distribution of fatal ICTAs were prepared while using Microsoft Excel and ArcGis9.2 software. The number of fatal car accidents showed a general increasing trend from 3000 in 1996 to 13500 in 2012. The incidence of fatal intercity car accidents has changed from six in 100000 population in 1996 to 18 in 100000 population in 2012. GIS based data showed that the incidence rate of ICTAs in different provinces of Iran was very divergent. The highest incidence of fatal ICTAs was in Semnan province (IR= 35.2), followed by North Khorasan (IR=22.7), and South Khorasan (IR=22). The least incidence of fatal ICTAs was in Tehran province (IR=2.4) followed by Khozestan (IR=6.5), and Eastern Azarbayejan (IR=6.6). The compensation cost of fatal ICTAs also showed an increasing trend during the studied period. Since an increasing amount of money was being paid yearly for the

  3. Road safety issues for bus transport management.

    Science.gov (United States)

    Cafiso, Salvatore; Di Graziano, Alessandro; Pappalardo, Giuseppina

    2013-11-01

    Because of the low percentage of crashes involving buses and the assumption that public transport improves road safety by reducing vehicular traffic, public interest in bus safety is not as great as that in the safety of other types of vehicles. It is possible that less attention is paid to the significance of crashes involving buses because the safety level of bus systems is considered to be adequate. The purpose of this study was to evaluate the knowledge and perceptions of bus managers with respect to safety issues and the potential effectiveness of various technologies in achieving higher safety standards. Bus managers were asked to give their opinions on safety issues related to drivers (training, skills, performance evaluation and behaviour), vehicles (maintenance and advanced devices) and roads (road and traffic safety issues) in response to a research survey. Kendall's algorithm was used to evaluate the level of concordance. The results showed that the majority of the proposed items were considered to have great potential for improving bus safety. The data indicated that in the experience of the participants, passenger unloading and pedestrians crossing near bus stops are the most dangerous actions with respect to vulnerable users. The final results of the investigation showed that start inhibition, automatic door opening, and the materials and internal architecture of buses were considered the items most strongly related to bus passenger safety. Brake assistance and vehicle monitoring systems were also considered to be very effective. With the exception of driver assistance systems for passenger and pedestrian safety, the perceptions of the importance of other driver assistance systems for vehicle monitoring and bus safety were not unanimous among the bus company managers who participated in this survey. The study results showed that the introduction of new technologies is perceived as an important factor in improving bus safety, but a better understanding

  4. American fuel cell bus project : first analysis report.

    Science.gov (United States)

    2013-06-01

    This report summarizes the experience and early results from the American Fuel Cell Bus Project, a fuel cell electric bus demonstration : funded by the Federal Transit Administration (FTA) under the National Fuel Cell Bus Program. A team led by CALST...

  5. Fuel Cell Electric Bus Evaluations | Hydrogen and Fuel Cells | NREL

    Science.gov (United States)

    Bus Evaluations Fuel Cell Electric Bus Evaluations NREL's technology validation team evaluates fuel cell electric buses (FCEBs) to provide comprehensive, unbiased evaluation results of fuel cell bus early transportation applications for fuel cell technology. Buses operate in congested areas where

  6. American Fuel Cell Bus Project Evaluation: Third Report

    Energy Technology Data Exchange (ETDEWEB)

    Eudy, Leslie [National Renewable Energy Lab. (NREL), Golden, CO (United States); Post, Matthew [National Renewable Energy Lab. (NREL), Golden, CO (United States); Jeffers, Matthew [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2017-05-01

    This report presents results of the American Fuel Cell Bus (AFCB) Project, a demonstration of fuel cell electric buses operating in the Coachella Valley area of California. The prototype AFCB, which was developed as part of the Federal Transit Administration's (FTA) National Fuel Cell Bus Program, was delivered to SunLine in November 2011 and was put in revenue service in mid-December 2011. Two new AFCBs with an upgraded design were delivered in June/July of 2014 and a third new AFCB was delivered in February 2015. FTA and the AFCB project team are collaborating with the U.S. Department of Energy (DOE) and DOE's National Renewable Energy Laboratory to evaluate the buses in revenue service. This report covers the performance of the AFCBs from July 2015 through December 2016.

  7. Design & Development of FPGA Based VME Bus Controller

    OpenAIRE

    Himali Patel; Poornima Talwai

    2015-01-01

    The VME bus interface Controller (VIC068A) is used to interface Local CPU bus and VME bus. VME Bus Controller is used in wide application areas where high reliability, good accuracy and high speed are desired to withstand industrial environment like nuclear power plant and process industries. VME Bus controller can configure as Master, Slave, Interrupt Handler, arbiter as well as power monitor. Commercial VME Bus interface controller chips are available from a few vend...

  8. Mastering NServiceBus and persistence

    CERN Document Server

    Helton, Rich

    2014-01-01

    This book is intended for developers, designers, and architects alike who wish to build C# NServiceBus enterprise architectures and learn how ESB persists data and messages to help them attain their goals. No prior knowledge of persistence in NServiceBus is required.

  9. Digital processing data communication systems (bus systems)

    International Nuclear Information System (INIS)

    Fleck, K.

    1980-01-01

    After an introduction to the technology of digital processing data communication systems there are the following chapters: digital communication of processing data in automation technology, the technology of biserial communication, the implementaiton of a bus system, the data transmission of the TDC-2000 system of Honeywell's and the process bus CS 275 in the automation system TELEPERM M of Siemens AG. (WB) [de

  10. First multivendor scheme in CFE to protection of 400 kV transmission line, using optical TC's, digital relays and bus IEC 61850-9-2; Primer esquema multivendedor en CFE para proteccion de linea de transmision de 400 kV, utilizando TC's opticos, relevadores digitales y bus IEC 61850-9-2

    Energy Technology Data Exchange (ETDEWEB)

    Garcia-Colon, V.R; Rasgado, J.P [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico); Lara C, H; Melendez, C; Juarez, N [Subdireccion de Transmision, Comision Federal de Electricidad (Mexico)

    2013-03-15

    This paper presents the details of design, installation and putting into service in the Comision Federal de Electricidad (CFE), of the first multi-vendor scheme that exists in the world, for the protection of a 400kV transmission line, which uses optical current transformers and digital relays IEC 61850-9-2. This system arises as a pilot project of the Subdireccion de Transmision of the CFE with the Instituto de Investigaciones Electricas (IIE). To ensure success in the implementation of the protection scheme, CFE joined a team coordinated by the Instituto de Investigaciones Electricas (IIE)involving nine international companies and a university. Pilot protection scheme is in operation under continuous monitoring, in one of the transmission lines of CFE that interconnect Manuel Moreno Torres with El Juile substations. The construction features, the challenges that were overcome and the first results obtained in operation are presented below. [Spanish] Este articulo presenta los detalles del diseno, instalacion y puesta en servicio en la Comision Federal de Electricidad (CFE) del primer esquema multivendedor que existe en el mundo, para la proteccion de una linea de transmision de 400kV, que utiliza transformadores de corriente opticos y relevadores digitales IEC 61850-9-2. Este sistema surge como un proyecto piloto de la Subdireccion de Transmision de la CFE con el Instituto de Investigaciones Electricas (IIE). Para asegurar el exito en la implementacion del esquema de proteccion, la CFE integro un equipo de trabajo coordinado por el Instituto de Investigaciones Electricas (IIE) en el que participaron 9 empresas internacionales y una universidad. El esquema de proteccion piloto, se encuentra en operacion bajo monitoreo continuo, en una de las lineas de transmision de la CFE que interconecta las subestaciones de Manuel Moreno Torres y El Juile. Las caracteristicas de construccion, los retos que fueron vencidos y los primeros resultados obtenidos en su operacion se

  11. Biobjective Optimization and Evaluation for Transit Signal Priority Strategies at Bus Stop-to-Stop Segment

    Directory of Open Access Journals (Sweden)

    Rui Li

    2016-01-01

    Full Text Available This paper proposes a new optimization framework for the transit signal priority strategies in terms of green extension, red truncation, and phase insertion at the stop-to-stop segment of bus lines. The optimization objective is to minimize both passenger delay and the deviation from bus schedule simultaneously. The objective functions are defined with respect to the segment between bus stops, which can include the adjacent signalized intersections and downstream bus stops. The transit priority signal timing is optimized by using a biobjective optimization framework considering both the total delay at a segment and the delay deviation from the arrival schedules at bus stops. The proposed framework is evaluated using a VISSIM model calibrated with field traffic volume and traffic signal data of Caochangmen Boulevard in Nanjing, China. The optimized TSP-based phasing plans result in the reduced delay and improved reliability, compared with the non-TSP scenario under the different traffic flow conditions in the morning peak hour. The evaluation results indicate the promising performance of the proposed optimization framework in reducing the passenger delay and improving the bus schedule adherence for the urban transit system.

  12. Intercity deceased donor renal transplantation: A single-center experience from a developing country

    Directory of Open Access Journals (Sweden)

    T R Mehta

    2013-01-01

    Full Text Available In a developing country such as India, deceased donor renal transplantation (DDRTx accounts for only about 1% of all renal transplants (RTx. Our institute initiated an intercity DDRTx in the year 2006, which significantly increased the number of RTx. We retrieved 74 kidneys from 37 deceased donors from various cities of Gujarat from January 2006 to December 2009. We transplanted the allografts in 66 recipients and a retrospective analysis of the donor profile and management and recipient outcome was performed. The mean age of the donors was 43.3 ± 18.8 years. The causes of death included road traffic accident in 51.35% of the donors and cerebrovascular stroke in 48.65% of the donors; 83.78% of the donors required ionotropes for hemodynamic stability in addition to vigorous intravenous fluid replacement. The average urine output of the donors was 350 ± 150 mL. The organs were perfused and stored in HTK solution. The mean cold ischemia time (CIT was 9.12 ± 5.25 h. The mean anastomosis time in the recipient was 30.8 ± 8.7 min. 57.6% of the recipients established urine output on the operating table and 42.4% developed delayed graft function. At the end of 1 month after transplantation, the mean serum creatinine was comparable to the Ahmadabad city DDRTx, although the CIT was significantly longer in the intercity patients. Intercity organ harvesting is a viable option to increase the donor pool. Distance may not be an impediment, and good recipient outcome is possible in spite of prolonged CIT in case of proper harvesting and preservation.

  13. Bus Route Design with a Bayesian Network Analysis of Bus Service Revenues

    Directory of Open Access Journals (Sweden)

    Yi Liu

    2018-01-01

    Full Text Available A Bayesian network is used to estimate revenues of bus services in consideration of the effect of bus travel demands, passenger transport distances, and so on. In this research, the area X in Beijing has been selected as the study area because of its relatively high bus travel demand and, on the contrary, unsatisfactory bus services. It is suggested that the proposed Bayesian network approach is able to rationally predict the probabilities of different revenues of various route services, from the perspectives of both satisfying passenger demand and decreasing bus operation cost. This way, the existing bus routes in the studied area can be optimized for their most probable high revenues.

  14. Signs of musculoskeletal disorders in bus drivers and fare collectors

    Directory of Open Access Journals (Sweden)

    Malú de Oliveira Freire

    2007-09-01

    Full Text Available To describe the signs of musculoskeletal disorders (SMD in drivers and fare ollectors and to investigate their association with hours worked per day, nutritional status and level of physical activity (PA. A cross-sectional study undertaken with 40 bus drivers and 39 fare collectors working intercity routes. The “Nordic Musculoskeletal Questionnaire” was used to identify SMD. The working day was defi ned according to median values ( ABSTRACT O objetivo deste estudo foi descrever os sintomas de distúrbios osteomusculares (SDO em motoristas e cobradores de ônibus e investigar sua associação com jornada de trabalho, estado nutricional e nível de atividade física. Estudo transversal realizado com 40 motoristas e 39 cobradores de ônibus de viagens intermunicipais. Os SDO foram verificados, utilizando-se o Questionário Nórdico de Sintomas Osteomusculares. A jornada de trabalho foi categorizada a partir dos valores da mediana (< 8 horas e ≥ 8 horas. O índice de massa corporal (IMC foi usado para verificar o estado nutricional. O nível de atividade física foi avaliado, usando-se o Questionário Internacional de Atividade Física (versão curta. As associações foram verifi cadas por teste qui-quadrado. A freqüência de dor em alguma região do corpo (últimos 12 meses foi de 70,0% e 76,9% para motoristas e cobradores respectivamente; 30,0% dos motoristas e 33,3% dos cobradores referiram dor nos últimos 7 dias; 26,6% e 33,3% dos motoristas e cobradores, respectivamente, tiveram que evitar o trabalho devido às dores. As maiores prevalências (últimos 12 meses foram observadas nas seguintes regiões anatômicas: ombros (32,5%, para motoristas e; lombar (48,7%, para cobradores. Houve diferença significativa (p = 0,029 entre motoristas e cobradores quanto ao relato de dor na região “lombar”. A prevalência de sobrepeso foi maior nos motoristas (72,0% do que nos cobradores (33,3%, as diferenças foram signifi cativas (p = 0

  15. Bus and Tag Terminators for IBM system/360

    CERN Multimedia

    Control units were connected to the channels with "Bus and Tag" cable pairs. The bus cables carried the address and data information and the tag cables identified what data was on the bus. There were three general types of bus-and-tag cables produced by IBM.

  16. PCISIM - A Simulation Tool for PCI Bus Based Systems

    DEFF Research Database (Denmark)

    Sharp, Robin

    1999-01-01

    This document describes a PCI bus simulator for use in evaluating the feasibility of system designs based on this bus.......This document describes a PCI bus simulator for use in evaluating the feasibility of system designs based on this bus....

  17. Estudio operacional de carril bus y priorización semafórica en el eje Castilla-Hermida

    OpenAIRE

    Melero Gallego, Pilar

    2016-01-01

    RESUMEN: El presente estudio consiste en el análisis de las opciones para la priorización del transporte público en el eje Castilla – Hermida (Santander). Se plantean tres escenarios posibles, la situación inicial sin ningún tipo de priorización, la situación de la implantación de un carril reservado a autobuses en el margen derecho con priorización semafórica del carril bus, y una última en la que se plantea la implantación de un carril bus de prioridad intermitente (BLIP – Bus Lines With...

  18. Large truck and bus crash facts, 2010.

    Science.gov (United States)

    2012-09-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and : property damage only crashes involving large trucks and buses in 2010. Selected crash statistics on passenger : vehicles are also presen...

  19. Large truck and bus crash facts, 2012.

    Science.gov (United States)

    2014-06-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and property damage only crashes involving large trucks and buses in 2012. Selected crash statistics on passenger vehicles are also presented ...

  20. Large truck and bus crash facts, 2013.

    Science.gov (United States)

    2015-04-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and property damage only crashes involving large trucks and buses in 2013. Selected crash statistics on passenger vehicles are also presented ...

  1. Large truck and bus crash facts, 2009.

    Science.gov (United States)

    2011-10-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and : property damage only crashes involving large trucks and buses in 2009. Selected crash statistics on passenger : vehicles are also presen...

  2. Large truck and bus crash facts, 2011.

    Science.gov (United States)

    2013-10-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and : property damage only crashes involving large trucks and buses in 2011. Selected crash statistics on passenger : vehicles are also presen...

  3. Passenger bus industry weather information application.

    Science.gov (United States)

    2011-03-21

    Adverse weather significantly affects the United States national transportation system, including commercial companies : that rely on highways to support their enterprises. The Passenger Bus (Motorcoach) Industry (PBI) is one such affected : user who...

  4. Understanding & modeling bus transit driver availability.

    Science.gov (United States)

    2014-07-01

    Bus transit agencies are required to hire extraboard (i.e. back-up) operators to account for unexpected absences. Incorrect sizing of extra driver workforce is problematic for a number of reasons. Overestimating the appropriate number of extraboard o...

  5. Bicycle-bus conflict area study.

    Science.gov (United States)

    2009-11-01

    Increasing bicycle use and bus ridership are both desirable policy goals : from a sustainability standpoint, but on city streets these two modes of : transport are often in conflict. While occupying opposite ends of the size : and weight spectrum, th...

  6. TMS communications software. Volume 2: Bus interface unit

    Science.gov (United States)

    Gregor, P. J.

    1979-01-01

    A data bus communication system to support the space shuttle's Trend Monitoring System (TMS) and to provide a basis for evaluation of the bus concept is described. Installation of the system included developing both hardware and software interfaces between the bus and the specific TMS computers and terminals. The software written for the microprocessor-based bus interface units is described. The software implements both the general bus communications protocol and also the specific interface protocols for the TMS computers and terminals.

  7. Comparison and status of 32 bit backplane bus architectures

    International Nuclear Information System (INIS)

    Muller, K.D.

    1985-01-01

    With the introduction of 32 bit microprocessors several new 32 bit backplane bus architectures have been developed and are in the process for standardization. Among these are Future Bus (IEEE P896.1), VME-Bus (IEEE 1014), MULTIBUS II, Nu-Bus and Fastbus (IEEE 960). The paper describes and compares the main features of these bus architectures and mentions the status of national and international standardization efforts

  8. The seated bus passenger--a review.

    Science.gov (United States)

    Levis, J A

    1978-09-01

    The paper describes the inter-relationship of anthropometry, rig studies and dynamic testing of aspects related to problems of the seated bus passenger. It seeks to draw together sub-sections of a very large study sponsored by the government through the Transport and Road Research Laboratory and undertaken by the Human Factors Group of Leyland Truck and Bus. It is relevant to all those designing passenger carrying transport systems.

  9. The Gozo discovery bus : a successful experiment

    OpenAIRE

    Vella, Maryrose

    2008-01-01

    The introduction of a tourist discovery bus in Gozo came about as a result of an EU Project which is part of the Interreg III B Archimed programmes in which the Islands and Small States Institute of the University of Malta participated. Other countries participating in this programme besides Malta, represented by the Islands and Small States Institute, are Italy, Cyprus and Greece. The discovery bus service was aimed at encouraging more tourists to come to Gozo and enabling them to visit stra...

  10. NOC AND BUS ARCHITECTURE: A COMPARISON

    OpenAIRE

    RAJEEV KAMAL; NEERAJ YADAV

    2012-01-01

    Network-on-chip designs promise to offer considerable advantages over the traditional bus-based architecture. As continuing scaling of Moore’s law enables ever greater transistor densities, design complexity, power limitations and application convergence networks have started to replace busses in much smaller systems and the enhancement of NoC. This paper summarizes the advantages of the NoC and the limitations of traditional bus based architecture. In this paper we discuss a detailed compari...

  11. Common bus multinode sensor system

    International Nuclear Information System (INIS)

    Kelly, T.F.; Naviasky, E.H.; Evans, W.P.; Jefferies, D.W.; Smith, J.R.

    1988-01-01

    This patent describes a nuclear power plant including a common bus multinode sensor system for sensors in the nuclear power plant, each sensor producing a sensor signal. The system consists of: a power supply providing power; a communication cable coupled to the power supply; plural remote sensor units coupled between the cable and one or more sensors, and comprising: a direct current power supply, connected to the cable and converting the power on the cable into direct current; an analog-to-digital converter connected to the direct current power supply; an oscillator reference; a filter; and an integrated circuit sensor interface connected to the direct current power supply, the analog-to-digital converter, the oscillator crystal and the filter, the interface comprising: a counter receiving a frequency designation word from external to the interface; a phase-frequency comparator connected to the counter; an oscillator connected to the oscillator reference; a timing counter connected to the oscillator, the phase/frequency comparator and the analog-to-digital converter; an analog multiplexer connectable to the sensors and the analog-to-digital converter, and connected to the timing counter; a shift register operatively connected to the timing counter and the analog-to-digital converter; an encoder connected to the shift register and connectable to the filter; and a voltage controlled oscillator connected to the filter and the cable

  12. Security awareness for public bus transportation : case studies of attacks against the Israeli public bus system.

    Science.gov (United States)

    2012-03-01

    This report presents 16 case studies of attacks planned or carried out against Israeli bus targets, along with statistical data on the number, frequency, and lethality of attacks against bus targets that have taken place in Israel since 1970 and duri...

  13. Digital processing data communication systems (bus systems). Digitale Prozessdaten-Kommunikations-Systeme (Bus Systeme)

    Energy Technology Data Exchange (ETDEWEB)

    Fleck, K

    1980-01-01

    After an introduction to the technology of digital processing data communication systems there are the following chapters: digital communication of processing data in automation technology, the technology of biserial communication, the implementaiton of a bus system, the data transmission of the TDC-2000 system of Honeywell's and the process bus CS 275 in the automation system TELEPERM M of Siemens AG.

  14. Dynamic Bus Travel Time Prediction Models on Road with Multiple Bus Routes

    Science.gov (United States)

    Bai, Cong; Peng, Zhong-Ren; Lu, Qing-Chang; Sun, Jian

    2015-01-01

    Accurate and real-time travel time information for buses can help passengers better plan their trips and minimize waiting times. A dynamic travel time prediction model for buses addressing the cases on road with multiple bus routes is proposed in this paper, based on support vector machines (SVMs) and Kalman filtering-based algorithm. In the proposed model, the well-trained SVM model predicts the baseline bus travel times from the historical bus trip data; the Kalman filtering-based dynamic algorithm can adjust bus travel times with the latest bus operation information and the estimated baseline travel times. The performance of the proposed dynamic model is validated with the real-world data on road with multiple bus routes in Shenzhen, China. The results show that the proposed dynamic model is feasible and applicable for bus travel time prediction and has the best prediction performance among all the five models proposed in the study in terms of prediction accuracy on road with multiple bus routes. PMID:26294903

  15. Dynamic Bus Travel Time Prediction Models on Road with Multiple Bus Routes.

    Science.gov (United States)

    Bai, Cong; Peng, Zhong-Ren; Lu, Qing-Chang; Sun, Jian

    2015-01-01

    Accurate and real-time travel time information for buses can help passengers better plan their trips and minimize waiting times. A dynamic travel time prediction model for buses addressing the cases on road with multiple bus routes is proposed in this paper, based on support vector machines (SVMs) and Kalman filtering-based algorithm. In the proposed model, the well-trained SVM model predicts the baseline bus travel times from the historical bus trip data; the Kalman filtering-based dynamic algorithm can adjust bus travel times with the latest bus operation information and the estimated baseline travel times. The performance of the proposed dynamic model is validated with the real-world data on road with multiple bus routes in Shenzhen, China. The results show that the proposed dynamic model is feasible and applicable for bus travel time prediction and has the best prediction performance among all the five models proposed in the study in terms of prediction accuracy on road with multiple bus routes.

  16. Enabling Bus Transit Service Quality Co-Monitoring Through Smartphone-Based Platform

    DEFF Research Database (Denmark)

    Li, Corinna; Zegras, P. Christopher; Zhao, Fang

    2017-01-01

    ’ word, meaning “agencies using public feedback to supplement official monitoring and regulation.”] bus service quality. The pilot project adapted a smartphone-based travel survey system, Future Mobility Sensing, to collect real-time customer feedback and objective operational measurements on specific...... monitoring through a more real-time, customer-centric perspective. The pilot project operated publicly for 3 months on the Silver Line bus rapid transit in Boston, Massachusetts. Seventy-six participants completed the entrance survey; half of them actively participated and completed more than 500...

  17. An Extended IEEE 118-Bus Test System With High Renewable Penetration

    Energy Technology Data Exchange (ETDEWEB)

    Pena, Ivonne; Martinez-Anido, Carlo Brancucci; Hodge, Bri-Mathias

    2018-01-01

    This article describes a new publicly available version of the IEEE 118-bus test system, named NREL-118. The database is based on the transmission representation (buses and lines) of the IEEE 118-bus test system, with a reconfigured generation representation using three regions of the US Western Interconnection from the latest Western Electricity Coordination Council (WECC) 2024 Common Case [1]. Time-synchronous hourly load, wind, and solar time series are provided for over one year (8784 hours). The public database presented and described in this manuscript will allow researchers to model a test power system using detailed transmission, generation, load, wind, and solar data. This database includes key additional features that add to the current IEEE 118-bus test model, such as: the inclusion of 10 generation technologies with different heat rate functions, minimum stable levels and ramping rates, GHG emissions rates, regulation and contingency reserves, and hourly time series data for one full year for load, wind and solar generation.

  18. Ecodriving for Reduction of Bus Transit Emission with Vehicle’s Hybrid Dynamic Model

    Directory of Open Access Journals (Sweden)

    Xiuzheng Zheng

    2015-01-01

    Full Text Available This paper formulates a global ecodriving optimal control to advise the green driving speed for bus transit to minimize the exhaust emission using Vehicle-to-Infrastructure (V2I communication. Assuming communication between vehicles and infrastructure (V2I and knowledge of traffic signal timings and waiting passengers at stations are known, an optimal driving speed is proposed to minimize the total vehicle emissions of the bus route. The dwell time of the bus transit at each station which includes two parts is proposed. A traffic lights timing model is employed as constraints to control the formation of the green wave band. Vehicle specific power (VSP model is further applied to evaluate the exhaust emission level linked with the speed and acceleration of the bus transit. An approximate sixteen-kilometer traffic network including fourteen intersections and fifteen stations of Beijing bus transit line 1 in Chaoyang District, Beijing, is chosen to investigate the performance of the developed ecodriving approach.

  19. Classifying the Diversity of Bus Mapping Systems

    Science.gov (United States)

    Said, Mohd Shahmy Mohd; Forrest, David

    2018-05-01

    This study represents the first stage of an investigation into understanding the nature of different approaches to mapping bus routes and bus network, and how they may best be applied in different public transport situations. In many cities, bus services represent an important facet of easing traffic congestion and reducing pollution. However, with the entrenched car culture in many countries, persuading people to change their mode of transport is a major challenge. To promote this modal shift, people need to know what services are available and where (and when) they go. Bus service maps provide an invaluable element of providing suitable public transport information, but are often overlooked by transport planners, and are under-researched by cartographers. The method here consists of the creation of a map evaluation form and performing assessment of published bus networks maps. The analyses were completed by a combination of quantitative and qualitative data analysis of various aspects of cartographic design and classification. This paper focuses on the resulting classification, which is illustrated by a series of examples. This classification will facilitate more in depth investigations into the details of cartographic design for such maps and help direct areas for user evaluation.

  20. A Feeder-Bus Dispatch Planning Model for Emergency Evacuation in Urban Rail Transit Corridors

    Science.gov (United States)

    Wang, Yun; Yan, Xuedong; Zhou, Yu; Zhang, Wenyi

    2016-01-01

    The mobility of modern metropolises strongly relies on urban rail transit (URT) systems, and such a heavy dependence causes that even minor service interruptions would make the URT systems unsustainable. This study aims at optimally dispatching the ground feeder-bus to coordinate with the urban rails’ operation for eliminating the effect of unexpected service interruptions in URT corridors. A feeder-bus dispatch planning model was proposed for the collaborative optimization of URT and feeder-bus cooperation under emergency situations and minimizing the total evacuation cost of the feeder-buses. To solve the model, a concept of dummy feeder-bus system is proposed to transform the non-linear model into traditional linear programming (ILP) model, i.e., traditional transportation problem. The case study of Line #2 of Nanjing URT in China was adopted to illustrate the model application and sensitivity analyses of the key variables. The modeling results show that as the evacuation time window increases, the total evacuation cost as well as the number of dispatched feeder-buses decrease, and the dispatched feeder-buses need operate for more times along the feeder-bus line. The number of dispatched feeder-buses does not show an obvious change with the increase of parking spot capacity and time window, indicating that simply increasing the parking spot capacity would cause huge waste for the emergent bus utilization. When the unbalanced evacuation demand exists between stations, the more feeder-buses are needed. The method of this study will contribute to improving transportation emergency management and resource allocation for URT systems. PMID:27676179

  1. A Quantitative and Systematic Methodology to Investigate Energy Consumption Issues in Multimodal Intercity Transportation Systems

    Directory of Open Access Journals (Sweden)

    Lili Du

    2015-09-01

    Full Text Available Energy issues in transportation systems have garnered increasing attention recently. This study proposes a systematic methodology for policy-makers to minimize energy consumption in multimodal intercity transportation systems considering suppliers’ operational constraints and travelers’ mobility requirements. A bi-level optimization model is developed for this purpose and considers the air, rail, private auto, and transit modes. The upper-level model is a mixed integer nonlinear program aiming to minimize energy consumption subject to transportation suppliers’ operational constraints and traffic demand distribution to paths resulting from the lower-level model. The lower-level model is a linear program seeking to maximize the trip utilities of travelers. The interactions between the multimodal transportation suppliers and intercity traffic demand are considered under the goal of minimizing system energy consumption. The proposed bi-level mixed integer model is relaxed and transformed into a mathematical program with complementarity constraints, and solved using a customized branch-and-bound algorithm. Numerical experiments, conducted using multimodal travel options between Lafayette, Indiana and Washington, D.C. reiterate that shifting traffic demand from private cars to the transit and rail modes significantly reduce energy consumption. Moreover, the proposed methodology provides tools to quantitatively analyze system energy consumption and traffic demand distribution among transportation modes under specific policy instruments. The results illustrate the need to systematically incorporate the interactions among traveler preferences, network structure, and supplier operational schemes to provide policy-makers insights for developing traffic demand shift mechanisms to minimize system energy consumption. Hence, the proposed methodology provide policy-makers the capability to analyze energy consumption in the transportation sector by a

  2. Evaluating neighborhood structures for modeling intercity diffusion of large-scale dengue epidemics.

    Science.gov (United States)

    Wen, Tzai-Hung; Hsu, Ching-Shun; Hu, Ming-Che

    2018-05-03

    Dengue fever is a vector-borne infectious disease that is transmitted by contact between vector mosquitoes and susceptible hosts. The literature has addressed the issue on quantifying the effect of individual mobility on dengue transmission. However, there are methodological concerns in the spatial regression model configuration for examining the effect of intercity-scale human mobility on dengue diffusion. The purposes of the study are to investigate the influence of neighborhood structures on intercity epidemic progression from pre-epidemic to epidemic periods and to compare definitions of different neighborhood structures for interpreting the spread of dengue epidemics. We proposed a framework for assessing the effect of model configurations on dengue incidence in 2014 and 2015, which were the most severe outbreaks in 70 years in Taiwan. Compared with the conventional model configuration in spatial regression analysis, our proposed model used a radiation model, which reflects population flow between townships, as a spatial weight to capture the structure of human mobility. The results of our model demonstrate better model fitting performance, indicating that the structure of human mobility has better explanatory power in dengue diffusion than the geometric structure of administration boundaries and geographic distance between centroids of cities. We also identified spatial-temporal hierarchy of dengue diffusion: dengue incidence would be influenced by its immediate neighboring townships during pre-epidemic and epidemic periods, and also with more distant neighbors (based on mobility) in pre-epidemic periods. Our findings suggest that the structure of population mobility could more reasonably capture urban-to-urban interactions, which implies that the hub cities could be a "bridge" for large-scale transmission and make townships that immediately connect to hub cities more vulnerable to dengue epidemics.

  3. VICbus: A standard inter-crate bus

    International Nuclear Information System (INIS)

    Parkman, C.F.

    1990-01-01

    VICbus is a standard inter-crate cable bus being developed by a working group of the ISO/IEC. Derived from an initiative of the VMEbus Working Group of ESONE, VICbus aims to provide users of multi-crate VMEbus and other backplane bus systems with a standard inter-crate connection. Multi-drop operation is provided for up to 31 devices on a cable of maximum 100 metres in length. Two data transfer protocols are specified, compelled (asynchronous) transfers for transparent interconnection of backplane bus systems (VMEbus in the first instance), and high-speed, non-compelled (synchronous) transfers between VICbus interfaces. A limited interrupt mechanism is specified, as well as simple, but efficient arbitration technique. Conventional technology is employed: copper cables, existing transcievers, and differential signal transmission, together with proven low-level protocols. Data transfer rates in excess of 30 Mbyte/s will be possible on a cable length of 30 metres

  4. Metro orange line BRT project evaluation.

    Science.gov (United States)

    2011-10-01

    In partnership with the Los Angeles County Metropolitan Transportation Authority (Metro) and the Federal Transit Administration (FTA), the National Bus Rapid Transit Institute (NBRTI) conducted an evaluation of the Metro Orange Line BRT service, whic...

  5. Risk factors affecting fatal bus accident severity: Their impact on different types of bus drivers.

    Science.gov (United States)

    Feng, Shumin; Li, Zhenning; Ci, Yusheng; Zhang, Guohui

    2016-01-01

    While the bus is generally considered to be a relatively safe means of transportation, the property losses and casualties caused by bus accidents, especially fatal ones, are far from negligible. The reasons for a driver to incur fatalities are different in each case, and it is essential to discover the underlying risk factors of bus fatality severity for different types of drivers in order to improve bus safety. The current study investigates the underlying risk factors of fatal bus accident severity to different types of drivers in the U.S. by estimating an ordered logistic model. Data for the analysis are retrieved from the Buses Involved in Fatal Accidents (BIFA) database from the USA for the years 2006-2010. Accidents are divided into three levels by counting their equivalent fatalities, and the drivers are classified into three clusters by the K-means cluster analysis. The analysis shows that some risk factors have the same impact on different types of drivers, they are: (a) season; (b) day of week; (c) time period; (d) number of vehicles involved; (e) land use; (f) manner of collision; (g) speed limit; (h) snow or ice surface condition; (i) school bus; (j) bus type and seating capacity; (k) driver's age; (l) driver's gender; (m) risky behaviors; and (n) restraint system. Results also show that some risk factors only have impact on the "young and elder drivers with history of traffic violations", they are: (a) section type; (b) number of lanes per direction; (c) roadway profile; (d) wet road surface; and (e) cyclist-bus accident. Notably, history of traffic violations has different impact on different types of bus drivers. Copyright © 2015 Elsevier Ltd. All rights reserved.

  6. Economic and demographic impacts of passenger rail systems : the impact of intercity passenger rails on population and employment change in the United States, 2000-2010.

    Science.gov (United States)

    2015-12-01

    This research examines the impact of intercity passenger rails on change in population and employment at the county level in the continental United States from 2000 to 2010. This research adopts an integrated spatial regression approach that incorpor...

  7. The Bus Station Spacing Optimization Based on Game Theory

    Directory of Open Access Journals (Sweden)

    Changjiang Zheng

    2015-01-01

    Full Text Available With the development of city, the problem of traffic is becoming more and more serious. Developing public transportation has become the key to solving this problem in all countries. Based on the existing public transit network, how to improve the bus operation efficiency, and reduce the residents transit trip cost has become a simple and effective way to develop the public transportation. Bus stop spacing is an important factor affecting passengers’ travel time. How to set up bus stop spacing has become the key to reducing passengers’ travel time. According to comprehensive traffic survey, theoretical analysis, and summary of urban public transport characteristics, this paper analyzes the impact of bus stop spacing on passenger in-bus time cost and out-bus time cost and establishes in-bus time and out-bus time model. Finally, the paper gets the balance best station spacing by introducing the game theory.

  8. Bus accident severity and passenger injury: evidence from Denmark

    DEFF Research Database (Denmark)

    Prato, Carlo Giacomo; Kaplan, Sigal

    2014-01-01

    Purpose Bus safety is a concern not only in developing countries, but also in the U.S. and Europe. In Denmark, disentangling risk factors that are positively or negatively related to bus accident severity and injury occurrence to bus passengers can contribute to promote safety as an essential...... principle of sustainable transit and advance the vision “every accident is one too many”. Methods Bus accident data were retrieved from the national accident database for the period 2002–2011. A generalized ordered logit model allows analyzing bus accident severity and a logistic regression enables...... examining occurrence of injury to bus passengers. Results Bus accident severity is positively related to (i) the involvement of vulnerable road users, (ii) high speed limits, (iii) night hours, (iv) elderly drivers of the third party involved, and (v) bus drivers and other drivers crossing in yellow or red...

  9. Connecticut Transit (CTTRANSIT) Fuel Cell Transit Bus Preliminary Evaluation Results

    Science.gov (United States)

    2008-10-16

    This report describes operations at Connecticut Transit (CTTRANSIT) in Hartford for one prototype fuel cell bus and three new diesel buses operating from the same location. The report discusses the planned fuel cell bus demonstration and equipment us...

  10. Request-Centric Wireless Bus Information Management System

    Directory of Open Access Journals (Sweden)

    Ying-Chih Chen

    2016-11-01

    Full Text Available This invention relates to a wireless bus information management system, which includes bus stop and vehicle management subsystems. The management signals are transmittable between bus stops and the vehicle. Based on vehicle management signals, the bus stop management subsystem can obtain information about the bus route identification, the number of unoccupied seats, the intention to stop or not, etc. Similarly, with the bus stop management signals, the vehicle management subsystem can make the decision of stopping. Accordingly, when a passenger wants to get off the vehicle or there are unoccupied seats, the vehicle management subsystem will inform the bus stop management subsystem such that the passengers waiting at the bus stop may flexibly schedule their travel plan. The proposed distributed wireless system is detailed by a prototype implementation and a simulation analysis, which is shown to be feasible and scalable.

  11. Analysis of a diesel-electric hybrid urban bus system

    Science.gov (United States)

    Marr, W. W.; Sekar, R. R.; Ahlheim, M. C.

    A hybrid bus powered by a diesel engine and a battery pack was analyzed over an idealized bus-driving cycle in Chicago. Three hybrid configurations, two parallel and one series, were evaluated. The results indicate that the fuel economy of a hybrid bus, taking into account the regenerative braking, is comparable with that of a conventional diesel bus. Life-cycle costs are slightly higher because of the added weight and cost of the battery.

  12. Security awareness for public bus transportation : case studies of attacks against the Israeli public bus system [research brief].

    Science.gov (United States)

    2012-03-01

    Government regulators and transportation operators of public bus systems are concerned about terrorist attacks. Bus attacks in Israel between late September 2000 and the end of 2006, a period known as the Second Intifada, are particularly well known....

  13. A programmable systolic trigger processor for FERA bus data

    International Nuclear Information System (INIS)

    Appelquist, G.; Hovander, B.; Sellden, B.; Bohm, C.

    1992-09-01

    A generic CAMAC based trigger processor module for fast processing of large amounts of ADC data, has been designed. This module has been realised using complex programmable gate arrays (LCAs from XILINX). The gate arrays have been connected to memories and multipliers in such a way that different gate array configurations can cover a wide range of module applications. Using this module, it is possible to construct complex trigger processors. The module uses both the fast ECL FERA bus and the CAMAC bus for inputs and outputs. The latter, however, is primarily used for set-up and control but may also be used for data output. Large numbers of ADCs can be served by a hierarchical arrangement of trigger processor modules, processing ADC data with pipe-line arithmetics producing the final result at the apex of the pyramid. The trigger decision will be transmitted to the data acquisition system via a logic signal while numeric results may be extracted by the CAMAC controller. The trigger processor was originally developed for the proposed neutral particle search experiment at CERN, NUMASS. There it was designed to serve as a second level trigger processor. It was required to correct all ADC raw data for efficiency and pedestal, calculate the total calorimeter energy, obtain the optimal time of flight data and calculate the particle mass. A suitable mass cut would then deliver the trigger decision. More complex triggers were also considered. (au)

  14. 76 FR 68819 - State of Good Repair Bus and Bus Facilities Discretionary Program Funds

    Science.gov (United States)

    2011-11-07

    ... Availability on June 24, 2011. The SGR Initiative makes funds available to public transit providers to finance capital projects to replace, rehabilitate, and purchase buses and related equipment and to construct bus...

  15. 76 FR 37393 - FY 2011 Discretionary Livability Funding Opportunity; Section 5309 Bus and Bus Facilities...

    Science.gov (United States)

    2011-06-27

    ... 90 percent Federal share for the total cost of a biodiesel bus. The Act also allows a 90 percent... transit systems or roadways. iv. Will improve accessibility and transport services for economically...

  16. Advanced Competencies for School Bus Drivers.

    Science.gov (United States)

    Illinois State Board of Education, Springfield.

    Four units are provided for formal classroom instruction in advanced competencies for school bus drivers in Illinois. Units cover passenger control, accidents and emergencies, detecting hazards, and first aid. Each unit contains some or all of the following components: table of contents; a list of objectives; informative material, including an…

  17. Functional Bus Driver-Pupil Passenger Relationships.

    Science.gov (United States)

    Farmer, Ernest

    1987-01-01

    Successful school bus drivers bring much more than mechanical know-how to the job. They develop good rapport with students while acting to bring undesirable student behavior under control. Drivers must also show an interest in students' welfare and have a good sense of humor. (MLH)

  18. School Bus Accidents: Reducing Incidents and Injuries

    Science.gov (United States)

    Mahoney, Daniel

    2009-01-01

    The number of children injured in nonfatal school bus accidents annually is more than double the number previously estimated. In Ohio alone, approximately 20,800 children younger than 18 were occupants of school buses that were involved in crashes in 2003 and 2004 (McGeehan 2007). Among those children, most had minor or no injuries. However, there…

  19. An Experimental Platform for Autonomous Bus Development

    Directory of Open Access Journals (Sweden)

    Héctor Montes

    2017-11-01

    Full Text Available Nowadays, with highly developed instrumentation, sensing and actuation technologies, it is possible to foresee an important advance in the field of autonomous and/or semi-autonomous transportation systems. Intelligent Transport Systems (ITS have been subjected to very active research for many years, and Bus Rapid Transit (BRT is one area of major interest. Among the most promising transport infrastructures, the articulated bus is an interesting, low cost, high occupancy capacity and friendly option. In this paper, an experimental platform for research on the automatic control of an articulated bus is presented. The aim of the platform is to allow full experimentation in real conditions for testing technological developments and control algorithms. The experimental platform consists of a mobile component (a commercial articulated bus fully instrumented and a ground test area composed of asphalt roads inside the Consejo Superior de Investigaciones Científicas (CSIC premises. This paper focuses also on the development of a human machine interface to ease progress in control system evaluation. Some experimental results are presented in order to show the potential of the proposed platform.

  20. Bus safety study : a report to Congress.

    Science.gov (United States)

    2013-11-01

    Section 20021(b) of the Moving Ahead for Progress for the 21st Century (MAP-21) legislation requires the Secretary of Transportation : to submit a report of the results of a Bus Safety Study to the Committee on Banking, Housing, and Urban Affai...

  1. Technology Validation: Fuel Cell Bus Evaluations

    Energy Technology Data Exchange (ETDEWEB)

    Eudy, Leslie [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2018-01-02

    This presentation describing the FY 2016 accomplishments for the National Renewable Energy Laboratory's Fuel Cell Bus Evaluations project was presented at the U.S. Department of Energy Hydrogen and Fuel Cells Program Annual Merit Review and Peer Evaluation Meeting, June 7, 2016.

  2. Repeater For A Digital-Communication Bus

    Science.gov (United States)

    Torres-Guzman, Esteban; Olson, Stephen; Heaps, Tim

    1993-01-01

    Digital repeater circuit designed to extend range of communication on MIL-STD-1553 bus beyond original maximum allowable length of 300 ft. Circuit provides two-way communication, one way at time, and conforms to specifications of MIL-STD-1553. Crosstalk and instability eliminated.

  3. Energy DataBus (Fact Sheet)

    Energy Technology Data Exchange (ETDEWEB)

    2013-07-01

    NREL has developed the Energy DataBus, an open-sourced software that collects massive amounts of energy-related data at second-to-second intervals; stores it in a massive, scalable database; and turns it into useful information.

  4. Stochastic Bus Dispatching Model untuk Optimalisasi Jumlah Bus Transjakarta Koridor 3

    Directory of Open Access Journals (Sweden)

    Zahedi Zahedi

    2011-12-01

    Full Text Available The increasing number of road user causing traffic jam finds out a way, busway. However, in its implementation, the number of fleet available does not enough to take the passengers. It results in the an amassed of passengers at several bus stops. This leads to passenger dissatisfaction satisfaction which eventually causes Transjakarta users to reuse private cars. Definitely this situation may builds up traffic jams. Stochastic Bus Dispatching Model is used to simulate public transportation that operates regularly. 

  5. A synchronous serial bus for multidimensional array acoustic logging tool

    Science.gov (United States)

    Men, Baiyong; Ju, Xiaodong; Lu, Junqiang; Qiao, Wenxiao

    2016-12-01

    In high-temperature and spatial borehole applications, a distributed structure is employed in a multidimensional array acoustic logging tool (MDALT) based on a phased array technique for electronic systems. However, new challenges, such as synchronous multichannel data acquisition, multinode real-time control and bulk data transmission in a limited interval, have emerged. To address these challenges, we developed a synchronous serial bus (SSB) in this study. SSB works in a half-duplex mode via a master-slave architecture. It also consists of a single master, several slaves, a differential clock line and a differential data line. The clock line is simplex, whereas the data line is half-duplex and synchronous to the clock line. A reliable communication between the master and the slaves with real-time adjustment of synchronisation is achieved by rationally designing the frame format and protocol of communication and by introducing a scramble code and a Hamming error-correcting code. The control logic of the master and the slaves is realized in field programmable gate array (FPGA) or complex programmable logic device (CPLD). The clock speed of SSB is 10 MHz, the effective data rate of the bulk data transmission is over 99%, and the synchronous errors amongst the slaves are less than 10 ns. Room-temperature test, high-temperature test (175 °C) and field test demonstrate that the proposed SSB is qualified for MDALT.

  6. Germany's Intercity Express with ABB three-phase propulsion. The high-speed era begins for German Federal Railway

    Energy Technology Data Exchange (ETDEWEB)

    Schmidt, D.

    1991-01-01

    June 2, 1991, marked for German Federal Railway (DB) the start of a new era. On that day its new Intercity Express (ICE) trains began regular operation, setting new standards not only in travel comfort but also in technical and operational innovation. The train's present running speed on the Hamburg-Frankfurt-Munich line, which includes the longest section of DB's new high-speed 'Neubaustrecke' routes, is 250 km/h. Of the 60 ICE trains ordered by DB, 41 had been delivered by September 1991. ABB invested its entire AC drive know-how in the development of the train's power cars. Acting within a consortium, ABB Henschel supplied about one third of the electrical equipment, including transformers, power converters and the control equipment, which includes DAVID, a modern diagnostics system. Other ABB deliveries were the displays for the drivers' cabs and the locomotive's safety equipment. Among the mechanical parts ABB supplied were the bogies, doors, walls and roofs, and the brake modules. (orig.).

  7. Valuation of travel time savings for intercity travel: The Madrid-Barcelona corridor

    DEFF Research Database (Denmark)

    Roman, Concepcion; Carlos Martin, Juan; Espino, Raquel

    2014-01-01

    We derive values of travel time savings (VOT) for the Madrid-Barcelona corridor, linking the two largest cities in Spain, based on the estimation of discrete choice models among the main public transport services in the corridor: air transport, high speed rail (HSR) and bus. The new HSR alternative...... (which started to operate in February 2008) competes directly with one of the densest airline domestic markets in the world, and its introduction produced substantial improvements in level of service, achieving reductions in travel time of more than 50% over the conventional train. A specifically...... to provide useful information to quantify users' benefits during the lifespan of a given project. We found, as expected, that HSR and air transport users exhibit substantially higher values for saving travel time than bus travellers. Also as expected, savings of waiting time are more valued than savings...

  8. Shuttle bus services quality assessment Tangerang Selatan toward smart city

    Science.gov (United States)

    Fassa, Ferdinand; Sitorus, Fredy Jhon Philip; Adikesuma, Tri Nugraha

    2017-11-01

    Around the world, shuttle bus operation played the significant role to accommodate transportation for commuting bus passengers. Shuttle Bus services in cities are provided by various bus agencies with kinds of own specific purposes. For instance, at Tangerang Selatan, Indonesia, it was said that shuttle bus In Trans Bintaro is run and operated by private bus companies hire by Bintaro developer. The aim of this research is to identify factors of satisfaction of shuttle bus service in Kota Tangerang Selatan, Indonesia. Several factors are used to analyze sums of 20 parameters performance indicators of Shuttle Bus. A face to face interview using a questionnaire (N=200) was used to collect data on October and March 2017. Likert and diagram Cartesian were used to model the all the parameters. This research succeeded in finding some categories of Shuttle bus service attributes such as accessibility, comfort, and safety. Users agreed that eight indicators in shuttle bus have the excellent achievement, while three indicators on performance remain low and should receive more attention especially punctuality of the bus.

  9. Study and Application of Forced Convection in Road Bus Heating System

    Directory of Open Access Journals (Sweden)

    Scheila Sandi Biazus

    2015-03-01

    Full Text Available This work deals with a replacing the heating system of intercity buses, made by long heat exchangers distributed on the sides of the passenger saloon by small and compact ones that use forced convection to heat dissipation. At the beginning the calculation was made of the heat capacity of a heat exchanger with the parameters defined by the supplier, and then conducted an analysis of change in these parameters in order to improve its efficiency. The method for examining the heat exchanger is based on the correlations available in the convection flow inside and outside to determine the respective convective coefficients, and therefore the overall coefficient of heat transfer. Following, the heat exchanger in its original form, was tested on bench. Thus, from the thermal load of the bus model studied, the amount of exchangers required has been defined to satisfy the thermal comfort of passengers. Field tests of the heating systems with new heat exchangers were performed to obtain actual data of the proposed system. The original factory system showed to be efficient in meeting the needs thermal load and economically viable, such that the critical thermal load can be met with ten heaters installed along the body. Furthermore, this system offers the possibility of varying the parameters to best fit to the project, where the flow variation of the fans or the spacing between the fins of the heat exchanger decreases the amount of heaters required. At the same time, the system showed the need for further study to assess its distribution along the passenger saloon in order to meet a best uniformity temperature distribution.

  10. Concise N-doped Carbon Nanosheets/Vanadium Nitride Nanoparticles Materials via Intercalative Polymerization for Supercapacitors.

    Science.gov (United States)

    Tan, Yongtao; Liu, Ying; Tang, Zhenghua; Wang, Zhe; Kong, Lingbin; Kang, Long; Liu, Zhen; Ran, Fen

    2018-02-13

    N-doped carbon nanosheets/vanadium nitride nanoparticles (N-CNS/VNNPs) are synthesized via a novel method combining surface-initiated in-situ intercalative polymerization and thermal-treatment process in NH 3 /N 2 atmosphere. The pH value of the synthesis system plays a critical role in constructing the structure and enhancing electrochemical performance for N-CNS/VNNPs, which are characterized by SEM, TEM, XRD, and XPS, and measured by electrochemical station, respectively. The results show that N-CNS/VNNPs materials consist of 2D N-doped carbon nanosheets and 0D VN nanoparticles. With the pH value decreasing from 2 to 0, the sizes of both carbon nanosheets and VN nanoparticles decreased to smaller in nanoscale. The maximum specific capacitance of 280 F g -1 at the current density of 1 A g -1 for N-CNS/VNNPs is achieved in three-electrode configuration. The asymmetric energy device of Ni(OH) 2 ||N-CNS/VNNPs offers a specific capacitance of 89.6 F g -1 and retention of 60% at 2.7 A g -1 after 5000 cycles. The maximum energy density of Ni(OH) 2 ||N-CNS/VNNPs asymmetric energy device is as high as 29.5 Wh kg -1 .

  11. VME bus based microcomputer system boards

    International Nuclear Information System (INIS)

    Chandra, A.K.; Ganesh, G.; Mayya, Anuradha; Chachondia, A.S.; Premraj, M.K.

    1991-01-01

    Several operator information systems for nuclear plants has been developed in the Division and these have involved extensive use of microcomputer boards for achieving various functions. Standard VME bus based boards have been developed to provide the most used functions. These boards have been fabricated and tested and used in several systems including Channel Temperature Monitoring systems, Disturbance Recording Systems etc. and are also proposed to be used in additional systems under developement. The use of standard bus and boards provides considerable savings in engineering time, prototyping, testing and evaluation costs, and maintenance support. This report desribes the various boards developed and the functions available on each. (author). 4 refs., 11 figs., 3 appendixes

  12. The Datacon Master -- Renovation of a Datacon field bus communications system for accelerator control

    International Nuclear Information System (INIS)

    Kerner, T.M.

    1995-01-01

    The Datacon system is a serial coaxial transformer isolated communication field bus system used to control and monitor accelerator remote devices. The Datacon field bus has been a BNL accelerator standard since its initial use in 1965. A single Datacon field bus supports up to 256 devices on a multidrop RG62A/U coaxial cable with up to 33 devices or 2,000 feet between repeaters or buffered branches. The forcing factor to renovate was the inability to repair the aging PDP-8E and PDP10 computers. The maintenance on this aging system was costly and the large number of accelerator devices dependent on the Datacon system could not be converted in a reasonable period of time to a new modern field bus. A commercial VMEbus host CPU mated with a custom designed VMEbus SBC event driven serial communications engine featuring a superscaler RISC 32-bit Intel i960 CPU met the design challenge. The commercial VMEbus host runs the VxWorks real-time operating system and connects to UNIX workstations over a Ethernet LAN. The V110 Datacon Master is the custom designed front end computer that integrates an accelerator event time line system with accelerator devices for up to 8 ppm users adding new capabilities

  13. Exposure Assessment of Diesel Bus Emissions

    Directory of Open Access Journals (Sweden)

    Werner Hofmann

    2006-12-01

    Full Text Available The goal of this study was to measure ultrafine particle concentrations with diameters less than 1 μm emitted by diesel buses and to assess resulting human exposure levels. The study was conducted at the Woolloongabba Busway station in Brisbane, Australia in the winter months of 2002 during which temperature inversions frequently occurred. Most buses that utilize the station are fuelled by diesel, the exhaust of which contains a significant quantity of particle matter. Passengers waiting at the station are exposed to these particles emitted from the buses. During the course of this study, passenger census was conducted, based on video surveillance, yielding person-by-person waiting time data. Furthermore, a bus census revealed accurate information about the total number of diesel versus Compressed Natural Gas (CNG powered buses. Background (outside of the bus station and platform measurements of ultrafine particulate number size distributions were made to determine ambient aerosol concentrations. Particle number exposure concentration ranges from 10 and 40 to 60% of bus related exhaust fumes. This changes dramatically when considering the particle mass exposure concentration, where most passengers are exposed to about 50 to 80% of exhaust fumes. The obtained data can be very significant for comparison with similar work of this type because it is shown in previous studies that exhaust emissions causes cancer in laboratory animals. It was assumed that significant differences between platform and background distributions were due to bus emissions which, combined with passenger waiting times, yielded an estimate of passenger exposure to ultrafine particles from diesel buses. From an exposure point of view, the Busway station analyzed resembles a street canyon. Although the detected exhaust particle concentration at the outbound platform is found to be in the picogram range, exposure increases with the time passengers spend on the platform

  14. Brazilian hybrid electric fuel cell bus

    Energy Technology Data Exchange (ETDEWEB)

    Miranda, P.E.V.; Carreira, E.S. [Coppe-Federal Univ. of Rio de Janeiro (Brazil). Hydrogen Lab.

    2010-07-01

    The first prototype of a hybrid electric fuel cell bus developed with Brazilian technology is unveiled. It is a 12 m urban-type, low-floor, air-conditioned bus that possesses three doors, air suspension, 29 seats and reversible wheelchair site. The bus body was built based on a double-deck type monoblock vehicle that is able to sustain important load on its roof. This allowed positioning of the type 3 hydrogen tanks and the low weight traction batteries on the roof of the vehicles without dynamic stabilization problems. A novel hybrid energy configuration was designed in such a way that the low-power (77 kWe) fuel cell works on steady-state operation mode, not responding directly to the traction motor load demand. The rate of kinetic energy regeneration upon breaking was optimized by the use of an electric hybrid system with predominance of batteries and also by utilizing supercapacitors. The electric-electronic devices and the security control softwares for the auxiliary and traction systems were developed in-house. The innovative hybrid-electric traction system configuration led to the possibility to decrease the fuel cell power, with positive impact on weight and system volume reduction, as well as to significantly decrease the hydrogen consumption. (orig.)

  15. Peptic ulcer among urban bus drivers in Denmark

    DEFF Research Database (Denmark)

    Netterstrøm, Bo; Juel, K

    1990-01-01

    As part of a survey on the work environment of bus drivers, 2045 (83%) of 2465 male bus drivers in the three major cities in Denmark in 1978 answered a postal questionnaire on health and working conditions. In order to evaluate the relative occurrence of peptic ulcer among the bus drivers, a follow......-up study was also conducted. All hospital discharges with a peptic ulcer diagnosis among the bus drivers were registered from the Danish National Patient Register. All Danish men were used as reference group. On the basis of the 1978-questionnaire association between occupational and psychosocial factors...... and subsequent hospital discharge with a peptic ulcer diagnosis was studied. The prevalence of abdominal pain alleviated by food intake was 12% among bus drivers and 6% in the reference group. The incidence of hospital discharge with duodenal ulcer among younger bus drivers was twice the incidence among Danish...

  16. Analytical approach for modeling and performance analysis of microring resonators as optical filters with multiple output bus waveguides

    Science.gov (United States)

    Lakra, Suchita; Mandal, Sanjoy

    2017-06-01

    A quadruple micro-optical ring resonator (QMORR) with multiple output bus waveguides is mathematically modeled and analyzed by making use of the delay-line signal processing approach in Z-domain and Mason's gain formula. The performances of QMORR with two output bus waveguides with vertical coupling are analyzed. This proposed structure is capable of providing wider free spectral response from both the output buses with appreciable cross talk. Thus, this configuration could provide increased capacity to insert a large number of communication channels. The simulated frequency response characteristic and its dispersion and group delay characteristics are graphically presented using the MATLAB environment.

  17. Aspek Hukum Perlindungan terhadap Penumpang Bus dalam Mewujudkan Perlindungan Konsumen

    OpenAIRE

    Harahap, Rabiah Z

    2016-01-01

    Bus is the one of transportation which is often used by society. Society as passenger of bus righteously gains protection. Many of accident happens in public transportation especially bus that rises a question the important of protection for people as the accicent victim. This question is worthy to be solved because many of public transportation company ignores the passenger's right. Based on this, government shall take control with presentation of new regulation that aims protection people ...

  18. Design Report for Isolated RS-485 Bus Node

    Science.gov (United States)

    2016-07-01

    TERMS Android , RS-485, isolated, USB, smartphone 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT UU 18. NUMBER...controlled wired RS-485 network. The Android -based smartphone or tablet is used in conjunction with a USB to serial bridge to operate as the bus master in...the system. The Android device operates in USB Host mode and communicates to the RS-485 bus as if a single peripheral on the USB bus. 15. SUBJECT

  19. Network Analysis of Urban Traffic with Big Bus Data

    OpenAIRE

    Zhao, Kai

    2016-01-01

    Urban traffic analysis is crucial for traffic forecasting systems, urban planning and, more recently, various mobile and network applications. In this paper, we analyse urban traffic with network and statistical methods. Our analysis is based on one big bus dataset containing 45 million bus arrival samples in Helsinki. We mainly address following questions: 1. How can we identify the areas that cause most of the traffic in the city? 2. Why there is a urban traffic? Is bus traffic a key cause ...

  20. Indonesian commercial bus drum brake system temperature model

    International Nuclear Information System (INIS)

    Wibowo, D. B.; Haryanto, I.; Laksono, N. P.

    2016-01-01

    Brake system is the most significant aspect of an automobile safety. It must be able to slow the vehicle, quickly intervening and reliable under varying conditions. Commercial bus in Indonesia, which often stops suddenly and has a high initial velocity, will raise the temperature of braking significantly. From the thermal analysis it is observed that for the bus with the vehicle laden mass of 15 tons and initial velocity of 80 km/h the temperature is increasing with time and reaches the highest temperature of 270.1 °C when stops on a flat road and reaches 311.2 °C on a declination road angle, ø, 20°. These temperatures exceeded evaporation temperature of brake oil DOT 3 and DOT 4. Besides that, the magnitude of the braking temperature also potentially lowers the friction coefficient of more than 30%. The brakes are pressed repeatedly and high-g decelerations also causes brake lining wear out quickly and must be replaced every 1 month as well as the emergence of a large thermal stress which can lead to thermal cracking or thermal fatigue crack. Brake fade phenomenon that could be the cause of many buses accident in Indonesia because of the failure of the braking function. The chances of accidents will be even greater when the brake is worn and not immediately replaced which could cause hot spots as rivets attached to the brake drum and brake oil is not changed for more than 2 years that could potentially lower the evaporation temperature because of the effect hygroscopic.

  1. Indonesian commercial bus drum brake system temperature model

    Science.gov (United States)

    Wibowo, D. B.; Haryanto, I.; Laksono, N. P.

    2016-03-01

    Brake system is the most significant aspect of an automobile safety. It must be able to slow the vehicle, quickly intervening and reliable under varying conditions. Commercial bus in Indonesia, which often stops suddenly and has a high initial velocity, will raise the temperature of braking significantly. From the thermal analysis it is observed that for the bus with the vehicle laden mass of 15 tons and initial velocity of 80 km/h the temperature is increasing with time and reaches the highest temperature of 270.1 °C when stops on a flat road and reaches 311.2 °C on a declination road angle, ø, 20°. These temperatures exceeded evaporation temperature of brake oil DOT 3 and DOT 4. Besides that, the magnitude of the braking temperature also potentially lowers the friction coefficient of more than 30%. The brakes are pressed repeatedly and high-g decelerations also causes brake lining wear out quickly and must be replaced every 1 month as well as the emergence of a large thermal stress which can lead to thermal cracking or thermal fatigue crack. Brake fade phenomenon that could be the cause of many buses accident in Indonesia because of the failure of the braking function. The chances of accidents will be even greater when the brake is worn and not immediately replaced which could cause hot spots as rivets attached to the brake drum and brake oil is not changed for more than 2 years that could potentially lower the evaporation temperature because of the effect hygroscopic.

  2. Indonesian commercial bus drum brake system temperature model

    Energy Technology Data Exchange (ETDEWEB)

    Wibowo, D. B., E-mail: rmt.bowo@gmail.com; Haryanto, I., E-mail: ismoyo2001@yahoo.de; Laksono, N. P., E-mail: priyolaksono89@gmail.com [Mechanical Engineering Dept., Faculty of Engineering, Diponegoro University (Indonesia)

    2016-03-29

    Brake system is the most significant aspect of an automobile safety. It must be able to slow the vehicle, quickly intervening and reliable under varying conditions. Commercial bus in Indonesia, which often stops suddenly and has a high initial velocity, will raise the temperature of braking significantly. From the thermal analysis it is observed that for the bus with the vehicle laden mass of 15 tons and initial velocity of 80 km/h the temperature is increasing with time and reaches the highest temperature of 270.1 °C when stops on a flat road and reaches 311.2 °C on a declination road angle, ø, 20°. These temperatures exceeded evaporation temperature of brake oil DOT 3 and DOT 4. Besides that, the magnitude of the braking temperature also potentially lowers the friction coefficient of more than 30%. The brakes are pressed repeatedly and high-g decelerations also causes brake lining wear out quickly and must be replaced every 1 month as well as the emergence of a large thermal stress which can lead to thermal cracking or thermal fatigue crack. Brake fade phenomenon that could be the cause of many buses accident in Indonesia because of the failure of the braking function. The chances of accidents will be even greater when the brake is worn and not immediately replaced which could cause hot spots as rivets attached to the brake drum and brake oil is not changed for more than 2 years that could potentially lower the evaporation temperature because of the effect hygroscopic.

  3. The value of an intercâmbio: brazilian student mobility, bilateralism & international education

    Directory of Open Access Journals (Sweden)

    Eric Spears

    2014-05-01

    Full Text Available Brazil’s emergence in the global economy as a member of the BRIC (Brazil, Russia, India, China, and South Africa states has prompted the federal government to establish the Brazilian Scientific Mobility Program (Science Without Borders in order to advance the country’s social capital and infrastructure in STEM (Science, Technology, Engineering, and Math related disciplines and industries. Public and private investment in the Scientific Mobility Program has transformed the way in which Brazilian government, universities, and citizenry places value the intercâmbio (student exchange experience in the United States. STEM-related disciplines are now disproportionately funded versus social sciences, humanities, and fine arts fields. This development has altered the way in which student mobility in the United States is given worth and changed the trajectory of international education in Brazil. This research provides a conceptual analysis of the Brazilian Scientific Mobility Program by using a critical political economy perspective. The essay conceptualizes the Science Without Borders initiative at global, national, and local levels. This research also explores what implications the bilateral U.S.-Brazil Educational Partnership may have on future policy, practice, and ultimately, funding of Brazilian student mobility. A emergência do Brasil no âmbito da economia mundializada como participante do BRIC (Brasil, Rússia, Índia, China e África do Sul mobilizou o governo federal brasileiro a estabelecer um programa estatal de mobilidade acadêmica (Programa Ciência sem Fronteiras de modo a fazer avançar o capital social do país (general intellect e a infraestrutura em STEM (Ciência, Tecnologia, Engenharia e Matemática relacionadas à indústria. Investimentos públicos e privados no programa de mobilidade acadêmica transformaram o modo como o governo brasileiro e as universidades valorizam o intercâmbio estudantil com os Estados Unidos. As

  4. Countermeasures for Developing New Energy Bus Standards in China

    Science.gov (United States)

    Shi, Xin

    2018-01-01

    With the rapid development of new energy vehicle technology, new energy bus has become more and more popular in China, and the relevant standards and policy are urgently needed to guide the market. According to the assessment of the development situation on new energy vehicle technology and new energy bus, combing with traffic policy guidance and the development trend of new energy vehicles, this paper aims to put forward the countermeasures of the new energy bus standard in China, including standard system, key standards and relevant recommendations. Research result is expected to provide decision support for the wide application of new energy bus in China.

  5. Status of the IEEE P896 Future Backplane Bus

    International Nuclear Information System (INIS)

    Gustavson, D.B.

    1983-10-01

    The IEEE P896 Future Backplane Bus project has been influenced by and has influenced FASTBUS and several other contemporary bus designs. This paper summarizes the current status of that project, which is directed toward the needs of modern 32-bit microprocessor systems with multiple processors. Some of the technology developed for P896 will be important for future non-ECL implementations of FASTBUS and other buses. In particular, new bus drivers and receivers should greatly improve the performance and reliability of backplane buses and cable buses. The current status of the P896 serial bus is also summarized

  6. The Software Bus, an Object-Oriented Data Exchange System

    International Nuclear Information System (INIS)

    Akerbaek, T.; Louka, M.

    1996-01-01

    This document describes the Software Bus System, developed for object-oriented task to task communication in a TCP/IP based network. The Software Bus is a set of library functions, developed to be used for the Picasso-3 UIMS, and as a general purpose tool for dynamically interfacing programs at run-time. The Software Bus offers a high level object-oriented data exchange mechanism that relieves the application programmer of the low level TCP/IP-programming and communication protocol handling. The Software Bus is currently available under several UNIX platforms and a version for Windows NT is planned for late 1996. (author)

  7. Examining the Association of Economic Development with Intercity Multimodal Transport Demand in China: A Focus on Spatial Autoregressive Analysis

    Directory of Open Access Journals (Sweden)

    Jinbao Zhao

    2018-02-01

    Full Text Available Transportation is generally perceived as a catalyst for economic development. This has been highlighted in previous studies. However, less attention has been paid to examine the relationship between economy and transport demand by exploring spatially cross-sectional data, especially for countries with significant regional economic imbalance, like China. In this article, we assess the economic influence of intercity multimodal transport demand at the prefecture level in China. Spatial autoregressive regression models are used to examine the impact of transport demand on economy by deep analysis of transport modes (land, air, and water and regions (eastern, central, and western. Through contrasting results from spatial lag model and spatial error model with those from the ordinary least square, this study finds that the estimation results can become more accurate by controlling for spatial autocorrelation, especially at the national level. Through rigorous analysis it is identified that except for water passenger traffic, all other intercity transport demand significantly contribute to a city’s economic development level in gross domestic product. In particular, air transport demands distribute more evenly and are estimated with the highest beta coefficients at both national and regional levels. In addition, the beta coefficients for land, air and water transportation are estimated with different magnitudes and significances at the national and regional levels. This study contributes to the ongoing discussion on the relationship between intercity multimodal transport demand and economic development level. Findings from this paper provide planning makers with valid and efficient strategies to better develop the economy by leveraging the special “⊣” cluster pattern of economic development and the benefits of air transportation.

  8. Integrated Optimization of Service-Oriented Train Plan and Schedule on Intercity Rail Network with Varying Demand

    Directory of Open Access Journals (Sweden)

    Wenliang Zhou

    2015-01-01

    Full Text Available For a better service level of a train operating plan, we propose an integrated optimization method of train planning and train scheduling, which generally are optimized, respectively. Based on the cost analysis of both passengers travelling and enterprises operation, and the constraint analysis of trains operation, we construct a multiobjective function and build an integrated optimization model with the aim of reducing both passenger travel costs and enterprise operating costs. Then, a solving algorithm is established based on the simulated annealing algorithm. Finally, using as an example the Changzhutan intercity rail network, as an example we analyze the optimized results and the influence of the model parameters on the results.

  9. Bus Rapid Transit and Socioeconomic Condition of Bus Commuters in Lagos State

    Directory of Open Access Journals (Sweden)

    Owolabi L. Kuye

    2017-10-01

    Full Text Available Road transport is one of the most common means of transportation across the world. Bus transportation in Nigeria had witnessed many problems for the past decades considering the growing population with the attendant loss of lives and properties in most cities like Lagos in Nigeria. This paper focuses on the adequacy of services provided by Bus Rapid Transit (BRT in Lagos State with respect to the extent to which it influences the socioeconomic conditions of bus commuters. It examines the effect of services rendered by BRT on cost reduction potential, income and safety. Multistage sampling technique was used to select 20 samples each from all respondents in all local government area in Lagos State to reach a total of three hundred and thirty (330 samples. The data collection instrument was the questionnaire which was validated. Data collected were analysed with the use of descriptive statistics such as means, percentages and standard deviation and inferential statistics such as regression and analysis of variance techniques. Findings showed that BRT services has reduced the cost of bus commuters and also increased safety and security thereby increasing the socioeconomic condition of Lagosians. The study recommends improvements in BRT services through the deployment of technology as it had been used in developed countries.

  10. Oracle Service Bus 11g Development Cookbook

    CERN Document Server

    Schmutz, Guido; van Zoggel, Jan

    2012-01-01

    This cookbook is full of immediately useable recipes showing you how to develop service and message-oriented (integration) applications on the Oracle Service Bus. In addition to its cookbook style, which ensures the solutions are presented in a clear step-by-step manner, the explanations go into great detail, which makes it good learning material for everyone who has experience in OSB and wants to improve. Most of the recipes are designed in such a way that each recipe is presented as a separate, standalone entity and reading of prior recipes is not required. The finished solution of each reci

  11. Bus bar joints stability and protection

    CERN Document Server

    Verweij, A

    2009-01-01

    A defective bus connection between two dipole magnets was the primary cause of the incident in sector 34 on September 19th. I will show how this could have happened, i.e. how a highly resistive joint has caused a thermal runaway and burned (or opened) before the QPS threshold was reached. In the second part of the talk I will present the new detection limits for the QPS upgrade of the RB and RQ circuits, required to avoid similar thermal runaways in the future.

  12. Redesign of Transjakarta Bus Driver's Cabin

    Science.gov (United States)

    Mardi Safitri, Dian; Azmi, Nora; Singh, Gurbinder; Astuti, Pudji

    2016-02-01

    Ergonomic risk at work stations with type Seated Work Control was one of the problems faced by Transjakarta bus driver. Currently “Trisakti” type bus, one type of bus that is used by Transjakarta in corridor 9, serving route Pinang Ranti - Pluit, gained many complaints from drivers. From the results of Nordic Body Map questionnaires given to 30 drivers, it was known that drivers feel pain in the neck, arms, hips, and buttocks. Allegedly this was due to the seat position and the button/panel bus has a considerable distance range (1 meter) to be achieved by drivers. In addition, preliminary results of the questionnaire using Workstation Checklist identified their complaints about uncomfortable cushion, driver's seat backrest, and the exact position of the AC is above the driver head. To reduce the risk level of ergonomics, then did research to design the cabin by using a generic approach to designing products. The risk analysis driver posture before the design was done by using Rapid Upper Limb Assessment (RULA), Rapid Entire Body Assessment (REBA), and Quick Exposure Checklist (QEC), while the calculation of the moment the body is done by using software Mannequin Pro V10.2. Furthermore, the design of generic products was done through the stages: need metric-matrix, house of quality, anthropometric data collection, classification tree concept, concept screening, scoring concept, design and manufacture of products in the form of two-dimensional. While the design after design risk analysis driver posture was done by using RULA, REBA, and calculation of moments body as well as the design visualized using software 3DMax. From the results of analysis before the draft design improvements cabin RULA obtained scores of 6, REBA 9, and the result amounted to 57.38% QEC and moment forces on the back is 247.3 LbF.inch and on the right hip is 72.9 LbF.in. While the results of the proposed improvements cabin design RULA obtained scores of 3, REBA 4, and the moment of force on

  13. Morphology of single inhalable particle inside public transit biodiesel fueled bus.

    Science.gov (United States)

    Shandilya, Kaushik K; Kumar, Ashok

    2010-01-01

    In an urban-transit bus, fueled by biodiesel in Toledo, Ohio, single inhalable particle samples in October 2008 were collected and detected by scanning electron microscopy and energy dispersive X-ray spectrometry (SEM/EDS). Particle size analysis found bimodal distribution at 0.2 and 0.5 microm. The particle morphology was characterized by 14 different shape clusters: square, pentagon, hexagon, heptagon, octagon, nonagon, decagon, agglomerate, sphere, triangle, oblong, strip, line or stick, and unknown, by quantitative order. The square particles were common in the samples. Round and triangle particles are more, and pentagon, hexagon, heptagon, octagon, nonagon, decagon, strip, line or sticks are less. Agglomerate particles were found in abundance. The surface of most particles was coarse with a fractal edge that can provide a suitable chemical reaction bed in the polluted atmospheric environment. The three sorts of surface patterns of squares were smooth, semi-smooth, and coarse. The three sorts of square surface patterns represented the morphological characteristics of single inhalable particles in the air inside the bus in Toledo. The size and shape distribution results were compared to those obtained for a bus using ultra low sulfur diesel.

  14. A Conceptual Approach for Optimising Bus Stop Spacing

    Science.gov (United States)

    Johar, Amita; Jain, S. S.; Garg, P. k.

    2017-06-01

    An efficient public transportation system is essential of any country. The growth, development and shape of the urban areas are mainly due to availability of good transportation (Shah et al. in Inst Town Plan India J 5(3):50-59, 1). In developing countries, like India, travel by local bus in a city is very common. The accidents, congestion, pollution and appropriate location of bus stops are the major problems arising in metropolitan cities. Among all the metropolitan cities in India, Delhi has highest percentage of growth of population and vehicles. Therefore, it is important to adopt efficient and effective ways to improve mobility in different metropolitan cities in order to overcome the problem and to reduce the number of private vehicles on the road. The primary objective of this paper is to present a methodology for developing a model for optimum bus stop spacing (OBSS). It describes the evaluation of existing urban bus route, data collection, development of model for optimizing urban bus route and application of model. In this work, the bus passenger generalized cost method is used to optimize the spacing between bus stops. For the development of model, a computer program is required to be written. The applicability of the model has been evaluated by taking the data of urban bus route of Delhi Transport Corporation (DTC) in Excel sheet in first phase. Later on, it is proposed to develop a programming in C++ language. The developed model is expected to be useful to transport planner for rational design of the spacing of bus stops to save travel time and to generalize operating cost. After analysis it is found that spacing between the bus stop comes out to be between 250 and 500 m. The Proposed Spacing of bus stops is done considering the points that they don't come nearer to metro/rail station, entry or exit of flyover and near traffic signal.

  15. Transient Stability Improvement of IEEE 9 Bus System Using Power World Simulator

    Directory of Open Access Journals (Sweden)

    Kaur Ramandeep

    2016-01-01

    Full Text Available The improvement of transient stability of power system was one of the most challenging research areas in power engineer.The main aim of this paper was transient stability analysis and improvement of IEEE 9 bus system. These studies were computed using POWER WORLD SIMULATOR. The IEEE 9 bus system was modelled in power world simulator and load flow studies were performed to determine pre-fault conditions in the system using Newton-Raphson method. The transient stability analysis was carried out using Runga method during three-phase balanced fault. For the improvement transient stability, the general methods adopted were fast acting exciters, FACT devices and addition of parallel transmission line. These techniques play an important role in improving the transient stability, increasing transmission capacity and damping low frequency oscillations.

  16. Schedule and complex motion of shuttle bus induced by periodic inflow of passengers

    Science.gov (United States)

    Nagatani, Takashi; Naito, Yuichi

    2011-09-01

    We have studied the dynamic behavior of a bus in the shuttle bus transportation with a periodic inflow. A bus schedule is closely related to the dynamics. We present the modified circle map model for the dynamics of the shuttle bus. The motion of the shuttle bus depends on the loading parameter and the inflow period. The shuttle bus displays the periodic, quasi-periodic, and chaotic motions with varying both loading parameter and inflow rate.

  17. 26 CFR 48.6427-2 - Credits or payments to purchaser of diesel or special motor fuels used in intercity, local, or...

    Science.gov (United States)

    2010-04-01

    ... compensation) passenger land transportation available to the general public or in a school bus in the... (for compensation) passenger land transportation available to the general public or in school bus... during the taxable year for passenger land transportation or school bus operations if section 6427(i) and...

  18. Illinois School Bus Driver Instructional Program. Trainee Guide. Revised.

    Science.gov (United States)

    Illinois State Board of Education, Springfield.

    This trainee guide contains six units of materials for use by those studying to become school bus drivers in the State of Illinois. Covered in the units are the following topics: school bus driver role and responsibility, passenger control, first aid, driving fundamentals, accidents and emergencies, and detecting hazards. Each unit contains a…

  19. Connecticut nutmeg fuel cell bus project : first analysis report.

    Science.gov (United States)

    2012-07-01

    This report summarizes the experience and early results from a fuel cell bus demonstration funded by the Federal Transit Administra-tion (FTA) under the National Fuel Cell Bus Program (NFCBP). A team led by the Northeast Advanced Vehicle Consortium a...

  20. Connecticut Transit (CTTRANSIT) Fuel Cell Transit Bus: Preliminary Evaluation Results

    Energy Technology Data Exchange (ETDEWEB)

    Chandler, K.; Eudy, L.

    2008-10-01

    This report provides preliminary results from a National Renewable Energy Laboratory evaluation of a protoptye fuel cell transit bus operating at Connecticut Transit in Hartford. Included are descriptions of the planned fuel cell bus demonstration and equipment; early results and agency experience are also provided.

  1. 3D reconstructions of a controlled bus bombing

    DEFF Research Database (Denmark)

    Villa, Chiara; Hansen, Nikolaj Friis; Hansen, Kamilla Maria

    2018-01-01

    Objectives: to demonstrate the usefulness of 3D reconstructions to better understand the dynamic of a controlled bus bombing. Materials and methods: 3D models of the victims (pigs) were created from post-mortem CT scanning using Mimic software; 3D models of the crime scene (bus) were generated by...

  2. Review of bus drivers' occupational stress and stress prevention

    NARCIS (Netherlands)

    Kompier, M.A.J.; Di Martino, V.

    1995-01-01

    Although heterogeneous in methodology and content, 32 studies from 13 countries on bus drivers' work and health are similar in their conclusions. Bus-driving–characterized by high demands, low control and low support – can be regarded as a classic example of high-strain occupation, with high risks

  3. 32 CFR 935.138 - Motor bus operation.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 6 2010-07-01 2010-07-01 false Motor bus operation. 935.138 Section 935.138 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE TERRITORIAL AND INSULAR REGULATIONS WAKE ISLAND CODE Motor Vehicle Code § 935.138 Motor bus operation. Each person operating a motor...

  4. Bus Lifecycle Cost Model for Federal Land Management Agencies.

    Science.gov (United States)

    2011-09-30

    The Bus Lifecycle Cost Model is a spreadsheet-based planning tool that estimates capital, operating, and maintenance costs for various bus types over the full lifecycle of the vehicle. The model is based on a number of operating characteristics, incl...

  5. A Joint Modeling Analysis of Passengers’ Intercity Travel Destination and Mode Choices in Yangtze River Delta Megaregion of China

    Directory of Open Access Journals (Sweden)

    Yanli Wang

    2016-01-01

    Full Text Available Joint destination-mode travel choice models are developed for intercity long-distance travel among sixteen cities in Yangtze River Delta Megaregion of China. The model is developed for all the trips in the sample and also by two different trip purposes, work-related business and personal business trips, to accommodate different time values and attraction factors. A nested logit modeling framework is applied to model trip destination and mode choices in two different levels, where the lower level is a mode choice model and the upper level is a destination choice model. The utility values from various travel modes in the lower level are summarized into a composite utility, which is then specified into the destination choice model as an intercity impedance factor. The model is then applied to predict the change in passenger number from Shanghai to Yangzhou between scenarios with and without high-speed rail service to demonstrate the applicability. It is helpful for understanding and modeling megaregional travel destination and mode choice behaviors in the context of developing country.

  6. Discriminating Intercalative Effects of Threading Intercalator Nogalamycin, from Classical Intercalator Daunomycin, Using Single Molecule Atomic Force Spectroscopy.

    Directory of Open Access Journals (Sweden)

    T Banerjee

    Full Text Available DNA threading intercalators are a unique class of intercalating agents, albeit little biophysical information is available on their intercalative actions. Herein, the intercalative effects of nogalamycin, which is a naturally-occurring DNA threading intercalator, have been investigated by high-resolution atomic force microscopy (AFM and spectroscopy (AFS. The results have been compared with those of the well-known chemotherapeutic drug daunomycin, which is a non-threading classical intercalator bearing structural similarity to nogalamycin. A comparative AFM assessment revealed a greater increase in DNA contour length over the entire incubation period of 48 h for nogalamycin treatment, whereas the contour length increase manifested faster in case of daunomycin. The elastic response of single DNA molecules to an externally applied force was investigated by the single molecule AFS approach. Characteristic mechanical fingerprints in the overstretching behaviour clearly distinguished the nogalamycin/daunomycin-treated dsDNA from untreated dsDNA-the former appearing less elastic than the latter, and the nogalamycin-treated DNA distinguished from the daunomycin-treated DNA-the classically intercalated dsDNA appearing the least elastic. A single molecule AFS-based discrimination of threading intercalation from the classical type is being reported for the first time.

  7. Optimal decisions of sharing rate and ticket price of different transportation modes in inter-city transportation corridor

    Directory of Open Access Journals (Sweden)

    Zhaoping Tang

    2015-11-01

    Full Text Available Purpose: The paper concerns competition of different transportation modes coexist in inter-city transportation corridor. The purpose of this paper is to express the competitive relationship by building mathematical model and obtain the best sharing rate and the optimal ticket price of different transportation modes. Design/methodology/approach: Firstly, analyzing influencing factors of passenger choice about transportation modes, we designed an utility function of transportation modes. Secondly, referring to the game theory and logit modle, a non-cooperative game model between railway and highway was built. Finally, the model was applied to Nanchang-Jiujiang transportation corridor in China for an empirical analysis. Findings: The results indicate that the proposed non-cooperative game model is rational and reliable, and it supplies a scientific method to determine the optimal ticket price and passenger sharing rate of different transportation modes, and can be applied to the competition study on different transportation modes in inter-city transportation corridor. Originality/value: The main contribution of this paper is to built the non-cooperative game model, which can consider the needs of different travelers, and achieve reasonable passenger divergence of different transportation modes and coordinated development of whole transport market.

  8. Discriminating Intercalative Effects of Threading Intercalator Nogalamycin, from Classical Intercalator Daunomycin, Using Single Molecule Atomic Force Spectroscopy.

    Science.gov (United States)

    Banerjee, T; Banerjee, S; Sett, S; Ghosh, S; Rakshit, T; Mukhopadhyay, R

    2016-01-01

    DNA threading intercalators are a unique class of intercalating agents, albeit little biophysical information is available on their intercalative actions. Herein, the intercalative effects of nogalamycin, which is a naturally-occurring DNA threading intercalator, have been investigated by high-resolution atomic force microscopy (AFM) and spectroscopy (AFS). The results have been compared with those of the well-known chemotherapeutic drug daunomycin, which is a non-threading classical intercalator bearing structural similarity to nogalamycin. A comparative AFM assessment revealed a greater increase in DNA contour length over the entire incubation period of 48 h for nogalamycin treatment, whereas the contour length increase manifested faster in case of daunomycin. The elastic response of single DNA molecules to an externally applied force was investigated by the single molecule AFS approach. Characteristic mechanical fingerprints in the overstretching behaviour clearly distinguished the nogalamycin/daunomycin-treated dsDNA from untreated dsDNA-the former appearing less elastic than the latter, and the nogalamycin-treated DNA distinguished from the daunomycin-treated DNA-the classically intercalated dsDNA appearing the least elastic. A single molecule AFS-based discrimination of threading intercalation from the classical type is being reported for the first time.

  9. Sustainable transport and the organisation of bus services in Manchester

    DEFF Research Database (Denmark)

    Gudmundsson, Henrik; Sørensen, Claus Hedegaard

    2008-01-01

    alternative modes of transport to private cars, such as public transport. In this paper we focus only on the potential of bus transport services in cities for attracting travellers from cars. It is a basic assumption behind this paper that the ability of public bus transport to attract travellers from cars...... depends on how the bus sector is organised. By organisation we adopt an institutional point of view and consider basic modes of governance. Basic modes of governance include the forms “market”, “hierarchy” and “network” (Powell 1990). So-called New Public Management (NPM) reforms have changed the modes...... of governance of bus transport in several countries, including Denmark and the United Kingdom. Our focus is on how New Public Mangement Reforms have changed the mix of governance modes and thus may have influenced the ability of urban bus transport to attract travellers from cars. We focus on a particular case...

  10. SISTEM RESERVASI TIKET BUS DI TERMINAL ARJOSARI MALANG

    Directory of Open Access Journals (Sweden)

    Surya Wirawan

    2013-10-01

    Full Text Available Bus Ticket Reservation System is an application that can be used to help booking bus tickets and the buyer will get a report via SMS Gateway. The reservation system is made by conducting field studies in Arjosari Bus Station Malang. This system uses SMS Gateway to send the report to the buyer after booking bus tickets online. SMS Gateway on this application serves as a liaison which delays sms between External Short Message entitiy (ESME and Short Message Service Center (SMSC and so does in reserve.The reservation system made is developed with the PHP programming language and has a prototype system pattern. System functions were tested using the validation testing, performance testing, and usability testing. The results percentage of responses usability testing is 67.7%. This shows that Ticket Reservation System at Arjosari Bus Station can be used well enough.

  11. Research on the Coordinated Design of Bus and Taxi Station

    Directory of Open Access Journals (Sweden)

    Jiangfeng Xi

    2015-01-01

    Full Text Available Rises in the number of transit buses, bus routes, and overall traffic volume in China’s cities, coupled with interference from other transport modes, such as taxis loading and unloading passengers nearby, have led to increasing traffic delays at bus stops, which is considered one of the factors degrading service levels and traffic operations on urban roadways. This paper studies traffic characteristics at bus stops, investigates variations in delay from different types or designs of bus stops, and analyzes the impact of it on traffic capacity, the purpose of which is to propose a solution to predicting the feasibility of an integrated design of bus stops and taxi stands with the help of mathematical models and based on the objectives of optimal traffic operations and passenger transfer.

  12. Improved design of HIRFL-CSR EVME bus controller

    International Nuclear Information System (INIS)

    Zhao Long; Liu Wufeng; Qiao Weimin; Jing Lan

    2009-01-01

    The EVME bus controller which is a key component of the HIRFL-CSR control system was improved. Besides reconfiguring the embedded Linux, a utility program was developed for data exchange between the controller and the database. The bus controller is based on ARM920T(ARM9) micro processor which is BGA packaged. The bus controller has the universal interface of VGA display, keyboard, and mouse. The backboard interface logic is programmed in an in-system configurable FPGA device. The bus can drive high current up to 64 mA, with the flexibility of the programmable signal definitions. All the improved performance helped the EVME bus controller play a crucial role in HIRFL-CSR control system. (authors)

  13. Bacterial Quality of Drinking Water in Bushehr Intercity Buses in 2010

    Directory of Open Access Journals (Sweden)

    Dariush Ranjbar Vakilabadi

    2012-12-01

    Full Text Available Background and Objective: Road transportation and specifically bus travel accounts for the bulk of travel. Contaminated drinking water consumption is one of the issues that threaten health, and always there is pollution possibility in drinking water in buses. This study evaluated the microbial quality of consumed drinking water in buses and also compared it with available standards. Materials and Methods: This study is a cross-sectional study. By considering similar studies, 95% confidence interval and based on the samples size formula for tradition of proportion, 80 buses from 122 buses that entered Bushehr Passenger Depot from other cities or exited it were randomly selected. Over a three-month period, samples were taken from drinking water in these buses. Temperature, pH, residual chlorine, total coliform (TC, and fecal coliform (E. coli in each sample were measured in accordance with the standard method. Statistical analysis of the data was carried out with SPSS Version 16, and the t-test was performed for statistical difference. Results: The results showed that residual chlorine in 97.5% was zero and pH values of the samples were in the range of 6.8-8.7. TC and E. coli numbers in 12.5% and 8.8% of the samples were higher than those of standards, respectively. Conclusion: Use of ice, washing time of the drinking water tank (daily or weekly, and method of usage and storage of drinking water (with 20-liter tanks had significant effects on the bacterial loads of the drinking water in the tanks (p value <0.05. Some factors such as tank material, driver's education and age, type and model of the bus, filling time of the tank (daily or weekly, the method of filling and emptying the tank (complete clearing out of the tank or otherwise, and distance had no significant effect on the quality of the drinking water in the buses.

  14. Work fatigue in urban bus drivers

    Directory of Open Access Journals (Sweden)

    Teresa Makowiec-Dąbrowska

    2015-10-01

    Full Text Available Background: Bus drivers are a special group of professional drivers who are at a very high risk of fatigue. The aim of the study was to examine whether the driver’s subjective assessment of fatigue allows for the determination of its level and identification of its causes. Material and Methods: The study group comprised 45 randomly selected bus drivers (mean age – 43.7±7.9 years, period of employment as drivers – 14.7±8.6 years. Examinations were performed in all subjects four times – before and after work on the “easy” route (outside the city center, small traffic intensity and before and after work on the “difficult” route (city center, heavy traffic. The fatigue test questionnaire, based on the list of symptoms of fatigue prepared by the Japan Research Committee of Fatigue, was used in the study. Results: The rating of fatigue after the work was significantly higher than that before the work. The profile of fatigue after work was not influenced by the type of route, but the assessment of most symptoms of fatigue reached a higher level after the “difficult” routes and the differences were statistically significant for 7 symptoms. Only the ratings of leg fatigue, feeling of heaviness, and the necessity to squint eyes and gaze with effort reached the higher levels after driving the “easy” routes. It has been found that the level of fatigue was significantly correlated with the job characteristics (driving time, the length of the route, number of stops, etc. and with the abundance of food ingested and type of beverage (coffee vs. others drunk prior to driving. Conclusions: The questionnaire used in our study to assess the subjective feeling of fatigue has proved to be a sensitive and useful tool for indicating the level and causes of fatigue. The relationship between the symptoms of fatigue and the characteristics of job and lifestyle shows that actions must be taken by both the employers and employees to prevent fatigue

  15. The Wheels on the Bus Go “Buy Buy Buy”: School Bus Advertising Laws

    Science.gov (United States)

    2012-01-01

    School buses, a practical necessity for millions of children, are at the center of new efforts to raise revenue. School bus advertising laws bring public health and commercialization concerns to the school setting. In doing so, they potentially expose school districts to First Amendment lawsuits. I examined various school bus advertising bills and laws. I reviewed First Amendment “forum analysis” as applied in the transit and school settings to clarify how this legal test may affect school districts subject to such laws. I have made recommendations for school districts to enact appropriate policies to ensure that such advertising does not undermine public health and to enable the districts to maintain control over their property. PMID:22742065

  16. The wheels on the bus go "buy buy buy": school bus advertising laws.

    Science.gov (United States)

    Pomeranz, Jennifer L

    2012-09-01

    School buses, a practical necessity for millions of children, are at the center of new efforts to raise revenue. School bus advertising laws bring public health and commercialization concerns to the school setting. In doing so, they potentially expose school districts to First Amendment lawsuits. I examined various school bus advertising bills and laws. I reviewed First Amendment "forum analysis" as applied in the transit and school settings to clarify how this legal test may affect school districts subject to such laws. I have made recommendations for school districts to enact appropriate policies to ensure that such advertising does not undermine public health and to enable the districts to maintain control over their property.

  17. Assessing Bus Performance Rating in Kajang, Selangor

    Science.gov (United States)

    Norhisham, S.; Ismail, A.; Sidek, L. M.; Borhan, M. N.; Zaini, N.; Yen, A. T. G.

    2018-04-01

    The Transit Capacity and Quality of Service Manual (TCQSM) was chosen based on the review with four manuals and guidelines for the method will be applied. Six (6) attributes, namely Hours of Service, Passenger Load, Transit Auto Travel Time, Service Frequency, Punctuality Performance and Service Coverage were chosen for evaluation.[6][7][8]. A total of three (3) operators with seven (7) routes were identified in Kajang. Based on the final results, the Quality of Service (QOS) findings was rated as D, which was regarded as minimum or satisfactory. Most stakeholders’ recommendations were: for the operators to provide information on bus scheduling and have accurate information for the passengers. It was suggested that in future this study can be extended to all routes and could be repeated after the opening of the Mass Rapid Transit (MRT) stations in Kajang, so as to provide a comparison and better evaluation of the public buses in Kajang.

  18. Bus bar electrical feedthrough for electrorefiner system

    Science.gov (United States)

    Williamson, Mark; Wiedmeyer, Stanley G; Willit, James L; Barnes, Laurel A; Blaskovitz, Robert J

    2013-12-03

    A bus bar electrical feedthrough for an electrorefiner system may include a retaining plate, electrical isolator, and/or contact block. The retaining plate may include a central opening. The electrical isolator may include a top portion, a base portion, and a slot extending through the top and base portions. The top portion of the electrical isolator may be configured to extend through the central opening of the retaining plate. The contact block may include an upper section, a lower section, and a ridge separating the upper and lower sections. The upper section of the contact block may be configured to extend through the slot of the electrical isolator and the central opening of the retaining plate. Accordingly, relatively high electrical currents may be transferred into a glovebox or hot-cell facility at a relatively low cost and higher amperage capacity without sacrificing atmosphere integrity.

  19. Field bus technology in accelerator control systems

    International Nuclear Information System (INIS)

    Tang Shuming

    1999-01-01

    Since eighties to now, the computer technology, network communication and ULSI technology have been developing rapidly. The level of control for industries and scientific experiments has been upgraded accordingly, so as to meet the increasing requirements for automation. The control systems become more complicated; the devices in control systems become more and more intelligent. However the cost of DCS (Distributed Control System) is quite expensive and the period of system integration is very long. More than ten measurement results for two methods defined in the world, in order to get inter operability of intelligent devices and reduce the costs. The author presents the development trend of fieldbuses briefly and describes the main performances of CAN, LONWORKS, WOLDFIP and PROFIBUS which are mainly used in the world today. The author proposes that the field bus technology will be introduced into the accelerator control systems in the country

  20. Status of the FASTBUS standard data bus

    International Nuclear Information System (INIS)

    Larsen, R.S.

    1980-11-01

    FASTBUS is a new laboratory standard data bus intended for use in experimental data acquisition and control. The development of FASTBUS began with a feasibility study in 1976, and is presently at the development prototyping stage. The principal aims of the standard are to provide a factor of ten or more improvement in speed of data transfers over present systems, as well as to provide an architecture for systems containing multiple processors. Developmental prototypes now in progress include crates, backplanes, cooling devices, power supplies, test and diagnostic modules, and user modules. A sizeable software development effort is also underway. Several experiments have made commitments to use FASTBUS. A review of current work and potential applications is given. 10 figures

  1. Cyber Risk Assessment of Transmission Lines in Smart Grids

    Directory of Open Access Journals (Sweden)

    Xuan Liu

    2015-12-01

    Full Text Available The increasing use of information technologies in power systems has increased the risk of power systems to cyber-attacks. In this paper, we assess the risk of transmission lines being overloaded due to cyber-based false data injection attacks. The cyber risk assessment is formulated as bilevel optimization problems that determine the maximum line flows under false data injection attacks. We propose efficient techniques to reduce the computation complexity of solving the bilevel problems. Specifically, primary and secondary filtering techniques are employed to identify the lines whose flows will never exceed their limits, which can significantly reduce computation burden. A special feasibility cut-based acceleration technique is introduced to further reduce the computation burden. The simulation results on the IEEE 30-bus, IEEE 118-bus, IEEE 300-bus and IEEE 2383-bus systems verify the proposed risk assessment model and the effectiveness of the proposed filtering and acceleration techniques.

  2. The influence of gymnastics in motor coordination and reaction time in urban public bus drivers

    Directory of Open Access Journals (Sweden)

    Stela Paula Mezzomo

    2014-12-01

    Full Text Available This study investigated the influence of labour gymnastics (LG on bus drivers' basic skills such as reaction time and gross motor coordination. Sixty male bus drivers (37.06 ± 7.66 years old from two bus lines in the city of Santa Maria (RS took part of this study. The participants were split into two groups, experimental group (EG and control group (CG. Subjects that were part of the EG took part in a LG intervention program, 2-3 times a week, over a year. Gross motor coordination was assessed by BURPEE Protocol (Johnson & Nelson, 1979, whereas reaction time by software providing a visual stimulus. Data normality was checked through Shapiro-Wilk test, which pointed to normal distribution only for the variables simple reaction time (SRT and choice reaction time (CRT in the EG. Therefore the non-parametric Mann-Whitney U test was selected to compare differences between groups. A statistically significant difference for gross motor coordination was found (z= −2.525, p= 0.012, suggesting the effectiveness of LG to improve motor skills. As regards SRT and CRT, no significant difference was found, in spite of better outcomes having been recorded after the LG program.

  3. Dynamic Voltage Stability Studies using a Modified IEEE 30-Bus System

    Directory of Open Access Journals (Sweden)

    Oluwafemi Emmanuel Oni

    2016-09-01

    Full Text Available Power System stability is an essential study in the planning and operation of an efficient, economic, reliable and secure electric power system because it encompasses all the facet of power systems operations, from planning, to conceptual design stages of the project as well as during the systems operating life span. This paper presents different scenario of power system stability studies on a modified IEEE 30-bus system which is subjected to different faults conditions. A scenario whereby the longest high voltage alternating current (HVAC line is replaced with a high voltage direct current (HVDC line was implemented. The results obtained show that the HVDC line enhances system stability more compared to the contemporary HVAC line. Dynamic analysis using RMS simulation tool was used on DigSILENT PowerFactory.

  4. Task Analysis Assessment on Intrastate Bus Traffic Controllers

    Science.gov (United States)

    Yen Bin, Teo; Azlis-Sani, Jalil; Nur Annuar Mohd Yunos, Muhammad; Ismail, S. M. Sabri S. M.; Tajedi, Noor Aqilah Ahmad

    2016-11-01

    Public transportation acts as social mobility and caters the daily needs of the society for passengers to travel from one place to another. This is true for a country like Malaysia where international trade has been growing significantly over the past few decades. Task analysis assessment was conducted with the consideration of cognitive ergonomic view towards problem related to human factors. Conducting research regarding the task analysis on bus traffic controllers had allowed a better understanding regarding the nature of work and the overall monitoring activities of the bus services. This paper served to study the task analysis assessment on intrastate bus traffic controllers and the objectives of this study include to conduct task analysis assessment on the bus traffic controllers. Task analysis assessment for the bus traffic controllers was developed via Hierarchical Task Analysis (HTA). There are a total of five subsidiary tasks on level one and only two were able to be further broken down in level two. Development of HTA allowed a better understanding regarding the work and this could further ease the evaluation of the tasks conducted by the bus traffic controllers. Thus, human error could be reduced for the safety of all passengers and increase the overall efficiency of the system. Besides, it could assist in improving the operation of the bus traffic controllers by modelling or synthesizing the existing tasks if necessary.

  5. Swisstrolley 3 - An articulated trolley bus; SWISSTROLLEY 3. Gelenktrolleybus

    Energy Technology Data Exchange (ETDEWEB)

    Gisler, H.-J.

    2006-07-01

    This illustrated final report for the Swiss Federal Office of Energy (SFOE) takes a look at the Swisstrolley 3 low-floor, articulated trolley bus developed in Switzerland by the Hess AG company. Various features of the variants of the trolley bus, including single vehicle, single and double-articulated buses and bus trailers, are discussed. The reductions achieved in energy consumption, weight and noise are discussed. Typical values for power consumption are presented in graphical form. Economic viability and passenger-friendliness are examined, as are possibilities for further improvement.

  6. DWPF Melter No.2 Prototype Bus Bar Test Report

    International Nuclear Information System (INIS)

    Gordon, J.

    2003-01-01

    Characterization and performance testing of a prototype DWPF Melter No.2 Dome Heater Bus Bar are described. The prototype bus bar was designed to address the design features of the existing system which may have contributed to water leaks on Melter No.1. Performance testing of the prototype revealed significant improvement over the existing design in reduction of both bus bar and heater connection maximum temperature, while characterization revealed a few minor design and manufacturing flaws in the bar. The prototype is recommended as an improvement over the existing design. Recommendations are also made in the area of quality control to ensure that critical design requirements are met

  7. Using microcomputers for lighting appliance control using a DALI bus

    Directory of Open Access Journals (Sweden)

    Sysala Tomas

    2016-01-01

    Full Text Available Article concerns the DALI bus theoretical and practical aspects. The DALI bus is a modern technology developed especially for illumination systems control. Authors are outlining communication basic principles related to the physical layer and going up to more complex data transactions among particular devices. The article main topic is aimed at two device models development based on microcontroller and exploiting that technology. The first of those two devices is a DALI slave unit enabling the light source or multi switch with light indication components control via DALI bus. The second device measures the ambient illumination intensity and it also detects errors in the load.

  8. Optimizing Performance of at-grade Intersection with Bus Rapid Transit Corridor and Heterogeneous Traffic

    Directory of Open Access Journals (Sweden)

    Hemant Kumar Sharma

    2012-06-01

    Full Text Available Bus Rapid Transit (BRT has emerged as a preferred mode of public transport in various countries all over the world for its cost effectiveness in construction as well as in operation and maintenance. The rapid transit feature of BRT is seen as a solution to many traffic problems in these countries. However, in developing countries like India, the right -of-way for most of the roads is restricted and traffic is heterogeneous in nature. Provision of BRT in existing right -of-way reduces the capacity available for other motorized traffic. As the buses travel with a certain frequency on dedicated bus- ways, the dedicated corridor remains unused for most of the period when other traffic on motorized vehicle (MV lanes suffers from congestion. The problem gets severe at intersections. However, if buses are operated in mixed traffic it is no more rapid transit. Hence, a solution is required to address this problem and optimize the performance of traffic as a whole. This paper presents the effect if dedicated bus-ways end at a reasonable distance before the stop line at a busy signalized at-grade intersection, and bus lanes (beyond that are made available to all the motorized vehicular traffic (heterogeneous traffic at intersection. The performance evaluation is done in terms of average queue length, maximum queue length, average delay time per vehicle, vehicle throughput, average speed in network and emission of Carbon monoxide CO, mono-nitrogen oxides NOx and Volatile organic compounds (VOC. It is observed that availability of bus lanes to other motorized traffic for a reasonable distance before intersection considerably reduces the average queue length, maximum queue length, average delay time per vehicle and emission per vehicle, while there is an increase in vehicle throughput and average speed of all the vehicles in the network. Thus it results in reduction of congestion and performance enhancement of at-grade intersections and network. Results of

  9. Bus systems in the automation- and process engineering. Fundamentals, systems and trends in the industrial communication. 6. rev. and actual. ed.; Bussysteme in der Automatisierungs- und Prozesstechnik. Grundlagen, Systeme und Trends der industriellen Kommunikation

    Energy Technology Data Exchange (ETDEWEB)

    Schnell, G.; Wiedemann, B. (eds.)

    2006-07-01

    This specialist book deals with the most important bussystems used in the automation. Special emphasis is given to field bussystems, may be master/slave or multimaster-systems. A comprehensive introduction to technical fundamentals informs about grid topologies, communication models, bus access processes, data saving, telegram formates, line standards, transmission possibilities and network connections. Special chapters are covering grid hierarchies by CIM and the international bus standardization. In the second part different bus systems are described in detail. The 6th edition is completed by themes about peripheral busses on PC (USB and firewire). (GL)

  10. In situ intercalative polymerization of poly (ε-caprolactone)/ 12-amino lauric acid-modified clay nano composites

    International Nuclear Information System (INIS)

    Reyes, Larry; Monserate, Juvy J.; Sumera, Florentino

    2013-01-01

    Polymer/layered silicate nano composites were prepared by in situ intercalative polymerization method from from ε-caprolactone (ε-CL) and 12-amino lauric acid modified montmorillonite (AMMT). The organo-modified clay was investigated for its capacity to facilitate ring-opening polymerization of ε-caprolactone within its silicate layers. The effect of varying the organo-modified clay loading (5%, 10% and 15% by weight) on the molecular weight of the poly (ε-caprolactone) (PCL) product was assessed by gel-permeation chromatography. The molecular weight of the polymer with different clay loadings ranged from ∼30,000 g/mo to ∼70,000 g/mol, where the 10% loading produced the highest molecular weight. Fourier Transform infrared (FTIR), and 1 H and 13 C Nuclear Magnetic Resonance (NMR) Spectroscopy were conducted to probe the composition of the polymer and the catalytic activity of AMMT to polymerize ε-CL. FTIR analyses showed two medium intensity and narrow CO-O stretching vibrations for the PCL products at around 1240 cm-1 and 1160 cm-1, which are attributed to ester skeletal backbone. 1 HNMR spectroscopic analysis revealed signals at 4.07 ppm and 3.66 ppm which can be attributed to εmethylene of caprolactone and methyl of ending ester group, respectively. The formation of the nano composites were assessed by X-ray Diffraction (XRD) and Transmission Electron Microscopy (TEM), XRD analyses showed a broadening and disappearance of diffraction peak of AMMT in the nana composite which may indicate the formation of the intercalated and partially exfoliated PCVL/AMMT nana composites. TEM observations corroborated the presence of intercalated and exfoliated layers of AMMT after polymerization. The present work demonstrates that AMMT can be used as an alternative g reen catalyst's for the production of biodegradable polymers, where the in situ intercalative polymerization was employed as a direct method of preparing polymer/layered silicates (author)

  11. Efficient and Robust Data Collection Using Compact Micro Hardware, Distributed Bus Architectures and Optimizing Software

    Science.gov (United States)

    Chau, Savio; Vatan, Farrokh; Randolph, Vincent; Baroth, Edmund C.

    2006-01-01

    Future In-Space propulsion systems for exploration programs will invariably require data collection from a large number of sensors. Consider the sensors needed for monitoring several vehicle systems states of health, including the collection of structural health data, over a large area. This would include the fuel tanks, habitat structure, and science containment of systems required for Lunar, Mars, or deep space exploration. Such a system would consist of several hundred or even thousands of sensors. Conventional avionics system design will require these sensors to be connected to a few Remote Health Units (RHU), which are connected to robust, micro flight computers through a serial bus. This results in a large mass of cabling and unacceptable weight. This paper first gives a survey of several techniques that may reduce the cabling mass for sensors. These techniques can be categorized into four classes: power line communication, serial sensor buses, compound serial buses, and wireless network. The power line communication approach uses the power line to carry both power and data, so that the conventional data lines can be eliminated. The serial sensor bus approach reduces most of the cabling by connecting all the sensors with a single (or redundant) serial bus. Many standard buses for industrial control and sensor buses can support several hundreds of nodes, however, have not been space qualified. Conventional avionics serial buses such as the Mil-Std-1553B bus and IEEE 1394a are space qualified but can support only a limited number of nodes. The third approach is to combine avionics buses to increase their addressability. The reliability, EMI/EMC, and flight qualification issues of wireless networks have to be addressed. Several wireless networks such as the IEEE 802.11 and Ultra Wide Band are surveyed in this paper. The placement of sensors can also affect cable mass. Excessive sensors increase the number of cables unnecessarily. Insufficient number of sensors

  12. Optimization Model for Headway of a Suburban Bus Route

    Directory of Open Access Journals (Sweden)

    Xiaohong Jiang

    2014-01-01

    Full Text Available Due to relatively low passenger demand, headways of suburban bus route are usually longer than those of urban bus route. Actually it is also difficult to balance the benefits between passengers and operators, subject to the service standards from the government. Hence the headway of a suburban bus route is usually determined on the empirical experience of transport planners. To cope with this problem, this paper proposes an optimization model for designing the headways of suburban bus routes by minimizing the operating and user costs. The user costs take into account both the waiting time cost and the crowding cost. The feasibility and validity of the proposed model are shown by applying it to the Route 206 in Jiangning district, Nanjing city of China. Weightages of passengers’ cost and operating cost are further discussed, considering different passenger flows. It is found that the headway and objective function are affected by the weightages largely.

  13. Large truck and bus crash facts, 2008. 

    Science.gov (United States)

    2010-03-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and : property damage only crashes involving large trucks and buses in 2008. Selected crash statistics on passenger : vehicles are also presen...

  14. CFD Investigation on Long-Haul Passenger Bus

    Science.gov (United States)

    Tan, C. F.; Tee, B. T.; Law, H. C.; Lim, T. L.

    2015-09-01

    Air flow distribution is one of the important factors that will influence the bus passenger comfort during long haul travel. Poor air flow distribution not only cause discomfort to the bus passenger but also influence their travel mode as well. The main purpose of this study is to investigate the air flow performance of the bus air-conditioning system through CFD simulation approach. A 3D CAD model of air ducts was drawn and hence analysed by using CFD software, namely ANSYS Fluent, to determine the airflow rate for every outlets of the air-conditioning system. The simulated result was then validated with experimental data obtained from prototype model of air duct. Based on the findings, new design concepts is proposed with the aim to meet the industry requirement as well as to improve the bus passenger comfort during long haul travel.

  15. Transit bus applications of lithium ion batteries : progress and prospects

    Science.gov (United States)

    2012-12-31

    This report provides an overview of diverse transit bus applications of advanced Lithium Ion Batteries (LIBs). The report highlights and illustrates several FTA programs that fostered the successful development, demonstration, and deployment of fuel-...

  16. Analysis of movable bus stop boarding and alighting areas.

    Science.gov (United States)

    2013-05-01

    This study explored the feasibility of using movable and reusable boarding and alighting (B&A) pads at bus stops. : Potential design alternatives in terms of materials and structural support for these pads were evaluated. The review : focused on the ...

  17. How to Reduce Those Costly School Bus Accidents.

    Science.gov (United States)

    Farmer, Ernest

    1985-01-01

    The deterrent to school bus accidents is preparedness. Training programs for drivers and mechanics, equipment specifications, and a community support base are some of the ways to prevent tragedy. (MLF)

  18. Southwest Direct Express Bus Demonstration in Orlando, FL

    Science.gov (United States)

    1988-04-01

    In August 1983, the Orange-Seminole-Osceola Transit Authority (OSOTA) initiated six express bus routes in the southwest corridor of Orlando (known collectively as the Southwest Direct) as an UMTA-funded demonstration project. While one objective of t...

  19. Black silicon solar cells with black bus-bar strings

    DEFF Research Database (Denmark)

    Davidsen, Rasmus Schmidt; Tang, Peter Torben; Mizushima, Io

    2016-01-01

    We present the combination of black silicon texturing and blackened bus-bar strings as a potential method for obtaining all-black solar panels, while using conventional, front-contacted solar cells. Black silicon was realized by maskless reactive ion etching resulting in total, average reflectance...... below 0.5% across a 156x156 mm2 silicon wafer. Four different methods to obtain blackened bus-bar strings were compared with respect to reflectance, and two of these methods (i.e., oxidized copper and etched solder) were used to fabricate functional allblack solar 9-cell panels. The black bus-bars (e.......g., by oxidized copper) have a reflectance below 3% in the entire visible wavelength range. The combination of black silicon cells and blackened bus-bars results in aesthetic, all-black panels based on conventional, front-contacted solar cells without compromising efficiency....

  20. Understanding Factors of Distraction among Intrastate Bus Driver

    Directory of Open Access Journals (Sweden)

    Yunos Muhammad Nur Annuar Mohd

    2017-01-01

    Full Text Available The increase in number of the world population have affected the demand for public transport especially in larger cities. Intrastate buses are chosen as the main public transport by many people due to its affordable fares. Therefore, a better performance of the intrastate bus drivers would be significant to cater the high demand. Nevertheless, distraction among the intrastate bus drivers have been found as one of the major factors that could affect the performance of the drivers. Therefore, the objective of this paper is to provide a better understanding on the factors of distraction among intrastate bus drivers. This paper refers to findings from previous researches which are related to this field of study. In conclusion, this paper will provide a list of factors of distraction among the intrastate bus drivers which may degrade their performance.

  1. FTA fuel cell bus program : research accomplishments through 2011.

    Science.gov (United States)

    2012-03-01

    Prepared by the Federal Transit Administration (FTA) Office of Research, Demonstration, and Innovation (TRI), this report summarizes the accomplishments of fuel-cell-transit-bus-related research and demonstrations projects supported by FTA through 20...

  2. STRATEGI PENGEMBANGAN TRANSPORTASI WISATA KURA-KURA BUS DI BALI

    Directory of Open Access Journals (Sweden)

    Ayu Kusuma

    2018-01-01

    Full Text Available Kura-Kura Bus is one of tourist transportation companies in Bali with public shuttle bus service in tourism route. Data analysis in this research were using SWOT and AHP analysis, with participants who have position minimal as a supervisor. Participants selected based on their expertise and relevance with this article. Based on the results of SWOT and AHP analysis to develop tourist transportation is Kura-Kura Bus, which is considered the most realistic scenario is an optimistic scenario, with the goal to be a safe and comfortable transportation. To achieve the goal, based on priority strategies that could be done by management of Kura-Kura Bus are developing unique products, finding new markets, favoring public transport services, enchance brand reputation, developing smartphone application, and cross promotion with supplier.

  3. DIMETHYL ETHER (DME)-FUELED SHUTTLE BUS DEMONSTRATION PROJECT

    Energy Technology Data Exchange (ETDEWEB)

    Elana M. Chapman; Shirish Bhide; Jennifer Stefanik; Howard Glunt; Andre L. Boehman; Allen Homan; David Klinikowski

    2003-04-01

    The objectives of this research and demonstration program are to convert a campus shuttle bus to operation on dimethyl ether, a potential ultra-clean alternative diesel fuel. To accomplish this objective, this project includes laboratory evaluation of a fuel conversion strategy, as well as, field demonstration of the DME-fueled shuttle bus. Since DME is a fuel with no lubricity (i.e., it does not possess the lubricating quality of diesel fuel), conventional fuel delivery and fuel injection systems are not compatible with dimethylether. Therefore, to operate a diesel engine on DME one must develop a fuel-tolerant injection system, or find a way to provide the necessary lubricity to the DME. In this project, they have chosen the latter strategy in order to achieve the objective with minimal need to modify the engine. The strategy is to blend DME with diesel fuel, to obtain the necessary lubricity to protect the fuel injection system and to achieve low emissions. The bulk of the efforts over the past year were focused on the conversion of the campus shuttle bus. This process, started in August 2001, took until April 2002 to complete. The process culminated in an event to celebrate the launching of the shuttle bus on DME-diesel operation on April 19, 2002. The design of the system on the shuttle bus was patterned after the system developed in the engine laboratory, but also was subjected to a rigorous failure modes effects analysis with help from Dr. James Hansel of Air Products. The result of this FMEA was the addition of layers of redundancy and over-pressure protection to the system on the shuttle bus. The system became operation in February 2002. Preliminary emissions tests and basic operation of the shuttle bus took place at the Pennsylvania Transportation institute's test track facility near the University Park airport. After modification and optimization of the system on the bus, operation on the campus shuttle route began in early June 2002. However, the

  4. The Major Roles Of Long Distance Bus Transport In Developing Countries With Emphasis On Addis Ababa, Ethiopia

    Directory of Open Access Journals (Sweden)

    Kassa Fekadu

    2015-03-01

    Full Text Available This article presents the major roles of long distance bus transport that radiates from Addis Ababa to the hinterland. The purpose is to assess and identify the major roles of Long Distance Bus Transport in Addis Ababa. The methodology is focused on both primary and secondary sources. The primary informants, who were principally distinguished from the passengers, operators, and key government officials from the transport office, include the head of bus terminal and Association, and selected experts. In terms of analysis, the qualitative approach was used by applying a thick description of the issue. The findings revealed that the availability of towns comes mainly because of the routes which give access and distribution of road passenger transport. The LDB (Long Distance Bus along the line has played a great role in the making of metropolitan linkage. The presence of these routes contributes more to the rise of urbanization and it has also played a role in the creation of towns and rural areas found around certain radius at the two sides of highways. Thus, it has a high probability for the expansion of urban sprawl and formation of conurbation in the future. The prescription for this study is to work with stakeholders to reduce the congestion of passengers in the terminals and the association also should serve the society 24/7 or 18/7.

  5. Scenario-based electric bus operation: A case study of Putrajaya, Malaysia

    OpenAIRE

    Lay Eng Teoh; Hooi Ling Khoo; Siew Yoke Goh; Lai Mun Chong

    2018-01-01

    Globally, transportation sector has emerged as one of the major sources of air pollution. Correspondingly, green mobility (with electric bus) is gaining increasing attention as an essential step to mitigate emission concern. As such, a proper electric bus network design and fleet planning is important especially for bus operator to acquire an adequate number of electric bus, right on time, in order to operate electric bus system viably. Thus, this paper aims to examine the possibility to oper...

  6. Regenerative Braking System for Series Hybrid Electric City Bus

    OpenAIRE

    Zhang, Junzhi; Lu, Xin; Xue, Junliang; Li, Bos

    2008-01-01

    Regenerative Braking Systems (RBS) provide an efficient method to assist hybrid electric buses achieve better fuel economy while lowering exhaust emissions. This paper describes the design and testing of three regenerative braking systems, one of which is a series regenerative braking system and two of which are parallel regenerative braking systems. The existing friction based Adjustable Braking System (ABS) on the bus is integrated with each of the new braking systems in order to ensure bus...

  7. Digital bus technology in new coal-fired plants

    Energy Technology Data Exchange (ETDEWEB)

    Blaney, J.; Murray, J. [Emerson Process Management (United States)

    2007-10-15

    The main issues associated with including digital bus technology such as Foundation fieldbus, Profibus-DP or DeviceNet, in a coal-fired power plant are deciding which systems to install and determining how to implement it. Although still new, digital bus experiences to date have shown that the technology performs solidly and when wiring best practices are followed a significantly shorted commissioning cycle can be achieved. 1 fig., 2 tabs.

  8. VHDL resolved function based inner communication bus for FPGA

    Science.gov (United States)

    Pozniak, Krzysztof T.

    2017-08-01

    This article discusses a method of building an internal, universal and parametric bus. The solution was designed for a variety of FPGA families and popular VHDL compilers. The algorithm of automatic configuration of address space and methods of receiving and sending addressed data are discussed. The basic solution realized in VHDL language in a behavioral form and chosen examples of practical use of the internal bus are presented in detail.

  9. Decreasing the exhaust outlet temperatures on a class III bus with the lowest impact on the exhaust backpressure and the fuel consumption

    Science.gov (United States)

    Aslan, E.; Ozturk, Y.; Dileroglu, S.

    2017-07-01

    The focus of this study is to determine the most appropriate exhaust tail pipe form among three different type of designs with respect to their temperature loss efficiency for a 9.5m intercity bus equipped with an Euro VI diesel engine and an automated transmission. To provide lower temperatures at the exhaust outlet, mentioned designs were submitted on to a CFD simulation using Ansys Fluent 17.1, while for manufactured products, temperature measurement tests were conducted in an environmental chamber with Omega K-type thermocouples, and Flir T420 thermal camera was used to monitor outer surface temperature distributions to make a comparison between theoretical and practical results. In order to obtain these practical results, actual tests were performed in an environmental chamber with a constant ambient temperature during the vehicle exhaust emission system regeneration process. In conclusion, an exhaust tail pipe design with a diffuser having a circular contraction and expansion forms is designated since it was the most optimized option in terms of temperature loss efficiency, inconsiderable exhaust backpressure increase and manufacturing costs.

  10. Effect of passenger position on fear of danger experienced during sudden bus stops.

    Science.gov (United States)

    Aoki, Takeo; Uetake, Teruo; Shimoda, Masahiro

    2009-06-01

    The purpose of this study was to identify the effect of bus passengers' positions on their fear of danger when a bus stopped suddenly. A temporary bus running course with one bus stop was set up on the campus of the Tokyo University of Agriculture and Technology (TUAT). The bus ran the course 14 times with the bus stopping twice during the course, once at the bus stop and again just after re-starting from the bus stop. The driver was asked to brake more strongly than usual when stopping. Sixteen students (15 males and 1 female) between the ages of 18 and 21 years participated. In turn, all participants were asked to take 14 different postures in the bus. Participants were also asked to report their level of fear on a rating scale each time the bus stopped. The study showed that (1) passengers' fear of danger at the first sudden stop was typically higher than that at the second stop, (2) standing passengers who held hand straps experienced more fear than those who held fixed safety devices, (3) bus passengers sitting on the centre of the rear seat had a great risk of injury if the bus stopped suddenly, and (4) when passengers faced the window and stood transversely with respect to from the moving direction of the bus and the bus stopped suddenly, passengers' fear of danger was affected by the side of the bus on which they stood as well as which hand they used to grasp a safety device.

  11. CROSS-FRONTIER PUBLIC TRANSPORT: Y BUS

    CERN Multimedia

    CERN Housing Service

    2002-01-01

    'Y' buses cover the journey between Val Thoiry in France (shopping centre including'Migros' and other stores) and Blandonnet in Switzerland, where they stop outside the 'Jumbo' shop, now renamed 'Carrefour'. In France, the buses connect up Thoiry, Sergy and St. Genis, then cross the border to stop outside CERN, Meyrin, before continuing towards Geneva along the 'Route de Meyrin', stopping outside the 'La Tour' hospital, then at the terminus Blandonnet. The normal fare on French territory with a slight incursion into Switzerland for this purpose as far as CERN, Meyrin, is 1.20 Euros per single journey (ticket valid for one hour). The same amount is charged for any single journey in Switzerland. For example, the cost of a single journey between St. Genis and the 'La Tour' hospital would be 2.40 Euros. The season ticket ('Abonnement de Travail') opens the right to purchase a ticket valid over any period of seven days which entitles the holder to as many journeys as required between the bus stop nearest to the pl...

  12. DIMETHYL ETHER (DME)-FUELED SHUTTLE BUS DEMONSTRATION PROJECT

    Energy Technology Data Exchange (ETDEWEB)

    Elana M. Chapman; Shirish Bhide; Jennifer Stefanik; Howard Glunt; Andre L. Boehman; Allen Homan; David Klinikowski

    2003-04-01

    The objectives of this research and demonstration program are to convert a campus shuttle bus to operation on dimethyl ether, a potential ultra-clean alternative diesel fuel. To accomplish this objective, this project includes laboratory evaluation of a fuel conversion strategy, as well as, field demonstration of the DME-fueled shuttle bus. Since DME is a fuel with no lubricity (i.e., it does not possess the lubricating quality of diesel fuel), conventional fuel delivery and fuel injection systems are not compatible with dimethyl ether. Therefore, to operate a diesel engine on DME one must develop a fuel-tolerant injection system, or find a way to provide the necessary lubricity to the DME. In this project, they have chosen the latter strategy in order to achieve the objective with minimal need to modify the engine. Their strategy is to blend DME with diesel fuel, to obtain the necessary lubricity to protect the fuel injection system and to achieve low emissions. The bulk of the efforts over the past year were focused on the conversion of the campus shuttle bus. This process, started in August 2001, took until April 2002 to complete. The process culminated in an event to celebrate the launching of the shuttle bus on DME-diesel operation on April 19, 2002. The design of the system on the shuttle bus was patterned after the system developed in the engine laboratory, but also was subjected to a rigorous failure modes effects analysis (FMEA, referred to by Air Products as a ''HAZOP'' analysis) with help from Dr. James Hansel of Air Products. The result of this FMEA was the addition of layers of redundancy and over-pressure protection to the system on the shuttle bus. The system became operational in February 2002. Preliminary emissions tests and basic operation of the shuttle bus took place at the Pennsylvania Transportation Institute's test track facility near the University Park airport. After modification and optimization of the system on

  13. Environmental Assessment of Bus Transport in the Trondheim Region - Evaluation of Relevant Bus and Fuel Technologies and their Potential for Mitigating Emissions from Passenger Transportation

    OpenAIRE

    Buø, Tonje

    2015-01-01

    The overall aim of this thesis is to assess the carbon footprint of transport by bus in the Trondheim region. Bus transportation is promoted as a strategy both to combat local pollution problems in urban areas and to mitigate global greenhouse gas emissions from passenger transport. Still, the environmental impacts of bus transport have received fairly limited attention in research. The environmental impacts of bus transport are calculated through life cycle assessment. A model is develo...

  14. IMPROVEMENT OF BUS OPERATIONAL CHARACTERISTICS WHILE USING INTEGRATED CONTROL OF SUSPENSION AND TRANSMISSION

    Directory of Open Access Journals (Sweden)

    V. V. Mikhailau

    2016-01-01

    Full Text Available Semi-natural tests for active pneumatic suspension of a 18-tonne tourist bus with the system of automatic body stabilization of the mobile machine and feed-back coupling according to kinematics parameter. The test have been executed in the cases when the bus is stocked with an automatic hydro-mechanical transmission in the process of speed picking up, gear-changing or road braking which is assigned by accidental road humps. A computer simulation of dynamic structures in combination with virtual devices and real objects (HIL – Hardware-in-the-Loop Simulation has been carried in the paper. Personal computers, software, programmed logic controller, frequency generator, solenoid-operated valve have been used for the investigation process. The paper proposes an unconventional method for improvement operational characteristics which is based on integrated control of a suspension and automatic hydro-mechanical transmission. A mathematical model includes systems of automatic transmission, suspension and module for generation of accidental road humps. The model has been considered as a basis for semi-natural laboratory bench with industrially-manufactured controller, other components of automatic systems and standard control organs. The most efficient method for body stabilization is control of the suspension according to the parameter of angular rate during vertical turn of an automobile’s center line with a turning point in the center of mass. The developed algorithm and stabilization system according to angular rate of body’s center line turning have made it possible to improve dynamics of the bus while making gear-changing and to reduce fuel consumption during starting-up and speed picking-up processes. During the braking process such system simultaneously decreases oscillation amplitude of some parameters more than two-fold.

  15. An evaluation of a lane support system for bus rapid transit on narrow shoulders and the relation to bus driver mental workload

    NARCIS (Netherlands)

    Ward, Nicholas J.; Shankwitz, Craig; Gorgestani, Alec; Donath, Max; De Waard, Dick; Boer, Erwin R.

    2006-01-01

    The use of dedicated bus shoulders is a key method for implementing bus rapid transit (BRT) in areas that do not have the space for additional infrastructure. However, the narrow width of the bus shoulder and the need to anticipate traffic hazards in the adjacent lane can both be significant

  16. An Improved Model for Headway-Based Bus Service Unreliability Prevention with Vehicle Load Capacity Constraint at Bus Stops

    Directory of Open Access Journals (Sweden)

    Weiya Chen

    2012-01-01

    Full Text Available This paper presents an improved model for improving headway-based bus route service reliability at bus stops using real-time preventive operation control, taking into account dynamic interaction among random passenger demand, stochastic driving conditions of route segments, and vehicle load capacity constraint. In this model, the real-time information of passenger demand and vehicle operation is involved to predict the imminent unacceptable headway deviation, in the case of which some in-time preventive control strategies are deployed according to the given control rules. As a case study, a single fixed bus route with high-frequency services was simulated and different scenarios of real-time preventive operation control were performed. Headway adherence and average passenger wait time were used to measure bus service reliability. The results show that the improved model is closer to the real bus route service, and using real-time information to predict potential service unreliability and trigger in-time preventive control can reduce bus bunching and avoid big gap.

  17. ANALISIS SARANA ANGKUTAN UMUM BUS DAMRI DI KOTA SEMARANG

    Directory of Open Access Journals (Sweden)

    Subhan Rizal Amin

    2015-12-01

    Full Text Available This study aims to analyze the availability and use of public transportation by taking a case study of the Damri bus which has Ngaliyan-Pucanggading route. The availability of public transport is not comparable to the demand for public transportation services so that the problems of transportation emerge. Additionally, the use of public transport becomes an important factor to develop the transportation. The study is conducted by surveying the Damri passengers of B.04 lane and logistic regression is used for the analysis. The method of determining the needs of transportation is issued by Departemen Perhubungan. It is used to calculate and determine whether the public transportation should be added or reduced. Then, the factors used as the independent variables in the analysis are the Damri’s safety, effectiveness, efficiency, service and reliability. The results show that Perum Damri does not need to add more Damri bus for B.04 because the results’ calculation is 0.6. and the factors that significantly influence the use Damri bus is the variable of safety, effectiveness and efficiency. However, the variables of service and reliability do not significantly influence the use of B.04 Damri bus.Penelitian ini bertujuan untuk menganalisis ketersediaan dan penggunaan angkutan sarana angkutan umum penumpang dengan mengambil studi kasus pada bus Damri jalur dengan trayek Ngaliyan-Pucanggading. Ketersediaan sarana angkutan umum yang tersedia tidak sebanding dengan besarnya permintaan akan jasa angkutan umum oleh masyarakat umum sehingga muncul permasalahan transportasi. Di samping itu, penggunaan angkutan umum yang beroperasi menjadi faktor penting dalam upaya pengembangan sarana transportasi. Penelitian ini dilakukan dengan menggunakan metode survey terhadap para penumpang bus Damri jalur B.04 dan dianalisis dengan Regresi Logistik. Metode penentuan kebutuhan armada dikeluarkan oleh Departemen Perhubungan yang digunakan untuk menghitung apakah suatu

  18. Circuit for Communication Over Power Lines

    Science.gov (United States)

    Krasowski, Michael J.; Prokop, Normal F.; Greer, Lawrence C., III; Nappier, Jennifer

    2011-01-01

    Many distributed systems share common sensors and instruments along with a common power line supplying current to the system. A communication technique and circuit has been developed that allows for the simple inclusion of an instrument, sensor, or actuator node within any system containing a common power bus. Wherever power is available, a node can be added, which can then draw power for itself, its associated sensors, and actuators from the power bus all while communicating with other nodes on the power bus. The technique modulates a DC power bus through capacitive coupling using on-off keying (OOK), and receives and demodulates the signal from the DC power bus through the same capacitive coupling. The circuit acts as serial modem for the physical power line communication. The circuit and technique can be made of commercially available components or included in an application specific integrated circuit (ASIC) design, which allows for the circuit to be included in current designs with additional circuitry or embedded into new designs. This device and technique moves computational, sensing, and actuation abilities closer to the source, and allows for the networking of multiple similar nodes to each other and to a central processor. This technique also allows for reconfigurable systems by adding or removing nodes at any time. It can do so using nothing more than the in situ power wiring of the system.

  19. Iterated Local Search Algorithm with Strategic Oscillation for School Bus Routing Problem with Bus Stop Selection

    Directory of Open Access Journals (Sweden)

    Mohammad Saied Fallah Niasar

    2017-02-01

    Full Text Available he school bus routing problem (SBRP represents a variant of the well-known vehicle routing problem. The main goal of this study is to pick up students allocated to some bus stops and generate routes, including the selected stops, in order to carry students to school. In this paper, we have proposed a simple but effective metaheuristic approach that employs two features: first, it utilizes large neighborhood structures for a deeper exploration of the search space; second, the proposed heuristic executes an efficient transition between the feasible and infeasible portions of the search space. Exploration of the infeasible area is controlled by a dynamic penalty function to convert the unfeasible solution into a feasible one. Two metaheuristics, called N-ILS (a variant of the Nearest Neighbourhood with Iterated Local Search algorithm and I-ILS (a variant of Insertion with Iterated Local Search algorithm are proposed to solve SBRP. Our experimental procedure is based on the two data sets. The results show that N-ILS is able to obtain better solutions in shorter computing times. Additionally, N-ILS appears to be very competitive in comparison with the best existing metaheuristics suggested for SBRP

  20. Schedule and complex motion of shuttle bus induced by periodic inflow of passengers

    International Nuclear Information System (INIS)

    Nagatani, Takashi; Naito, Yuichi

    2011-01-01

    We have studied the dynamic behavior of a bus in the shuttle bus transportation with a periodic inflow. A bus schedule is closely related to the dynamics. We present the modified circle map model for the dynamics of the shuttle bus. The motion of the shuttle bus depends on the loading parameter and the inflow period. The shuttle bus displays the periodic, quasi-periodic, and chaotic motions with varying both loading parameter and inflow rate. -- Highlights: → We studied the dynamic behavior of a bus in the shuttle bus transportation. → We presented the modified circle map model for the bus schedule. → We clarified the dependence of the tour time on both loading parameter and inflow period.

  1. Improvement of multiprocessing performance by using optical centralized shared bus

    Science.gov (United States)

    Han, Xuliang; Chen, Ray T.

    2004-06-01

    With the ever-increasing need to solve larger and more complex problems, multiprocessing is attracting more and more research efforts. One of the challenges facing the multiprocessor designers is to fulfill in an effective manner the communications among the processes running in parallel on multiple multiprocessors. The conventional electrical backplane bus provides narrow bandwidth as restricted by the physical limitations of electrical interconnects. In the electrical domain, in order to operate at high frequency, the backplane topology has been changed from the simple shared bus to the complicated switched medium. However, the switched medium is an indirect network. It cannot support multicast/broadcast as effectively as the shared bus. Besides the additional latency of going through the intermediate switching nodes, signal routing introduces substantial delay and considerable system complexity. Alternatively, optics has been well known for its interconnect capability. Therefore, it has become imperative to investigate how to improve multiprocessing performance by utilizing optical interconnects. From the implementation standpoint, the existing optical technologies still cannot fulfill the intelligent functions that a switch fabric should provide as effectively as their electronic counterparts. Thus, an innovative optical technology that can provide sufficient bandwidth capacity, while at the same time, retaining the essential merits of the shared bus topology, is highly desirable for the multiprocessing performance improvement. In this paper, the optical centralized shared bus is proposed for use in the multiprocessing systems. This novel optical interconnect architecture not only utilizes the beneficial characteristics of optics, but also retains the desirable properties of the shared bus topology. Meanwhile, from the architecture standpoint, it fits well in the centralized shared-memory multiprocessing scheme. Therefore, a smooth migration with substantial

  2. Scenario-based electric bus operation: A case study of Putrajaya, Malaysia

    Directory of Open Access Journals (Sweden)

    Lay Eng Teoh

    2018-03-01

    Full Text Available Globally, transportation sector has emerged as one of the major sources of air pollution. Correspondingly, green mobility (with electric bus is gaining increasing attention as an essential step to mitigate emission concern. As such, a proper electric bus network design and fleet planning is important especially for bus operator to acquire an adequate number of electric bus, right on time, in order to operate electric bus system viably. Thus, this paper aims to examine the possibility to operate electric bus as a replacement for the conventional bus operation (with natural gas buses for the study area in Putrajaya, Malaysia. In order to determine a proper-designed electric bus operating system in terms of electric bus route, service frequency and quantity, the proposed methodology is developed with the aid of a traffic modeling software to cater various scenarios. Based on the existing (conventional traffic and transit system in Putrajaya, the developed electric bus operating model is calibrated accordingly by considering various operational concerns including battery capacity and charging facility. The resultant findings revealed that the developed electric bus operating system in Putrajaya outperforms the conventional bus operation, not only in generating a higher profit margin for the bus operator, but also satisfying the passengers in a better manner (by carrying more passengers per unit of bus with a lower energy consumption.

  3. 23 CFR 450.104 - Definitions.

    Science.gov (United States)

    2010-04-01

    ... public, but does not include school bus, charter, or intercity bus transportation or intercity passenger... offer a significant alternative to regional highway travel. Revision means a change to a long-range...

  4. The modal transfer analysis by adding transport costs. Case study: The use of bus and private vehicle student Institut Teknologi Sumatera

    Science.gov (United States)

    Muliarto, H.; Alhamidi; Syahbandi, M.

    2017-06-01

    Since the last two years the Institut Teknologi Sumatera to accept new students in large numbers. Increasing the number of students is directly proportional to the increase of private vehicles that enter the campus it is not in line with the policy of the Institut Teknologi Sumatera as Smart, Friendly, and Forest Campus. Institut Teknologi Sumatera as Smart, Friendly, and Forest Campus fact has made some deal with mass public transport, Damri, to provide bus transportation to the Institut Teknologi Sumatera, but the number of bus users is still inferior to the number of private vehicle users. This study was conducted to see the modal transfer of the entire academic community ITERA, from private cars to public transport such as buses, with the addition of transportation costs in the form of parking rates. This study shows the dominant displacement can occur if the respondent charged parking fees of IDR 4.000. Besides the displacement mode of transportation from using private vehicles be using the bus can occur if Trans Lampung fix three systems including bus departure and arrival schedules, facility service providers that support, and the addition of the Bus Trans Lampung.

  5. Potential Influence of Metro on Bus: A Case Study

    Science.gov (United States)

    Selvakumar, M.; Abishek Reddy, M.; Sathish, V.; Venkatesh, R.

    2018-06-01

    A modal shift occurs when one mode of transport has a comparative advantage in a similar market over another. The present work concerns with the development of modal shift model for urban travel in Chennai, India. The modal shift model was calibrated using binary logit technique and validated using hold-out sample method. The validated model was used to predict the probability of shift in selected corridor. The recent introduction of metro rail in Chennai has lead to an increasing competition among public transport modes. To study the influence of metro on bus transport, a Stated Preference (SP) survey was conducted among express bus travellers. Using the SP survey data, a modal shift model was calibrated to estimate the plausible shift from bus to metro. Results indicate that variables like fare- difference, age, and income play an important role in the shift behaviour. When metro fare increases with respect to express bus fare, bus passengers are less willing to use metro and vice-versa.

  6. 1393 Ring Bus at JPL: Description and Status

    Science.gov (United States)

    Wysocky, Terry R.

    2007-01-01

    Completed Ring Bus IC V&V Phase - Ring Bus Test Plan Completed for SIM Project - Applicable to Other Projects Implemented a Avionics Bus Based upon the IEEE 1393 Standard - Excellent Starting Point for a General Purpose High-Speed Spacecraft Bus - Designed to Meet SIM Requirements for - Real-time deterministic, distributed systems. - Control system requirements - Fault detection and recovery Other JPL Projects Considering Implementation F'light Software Ring Bus Driver Module Began in 2006, Continues Participating in Standard Revision. Search for Earth-like planets orbiting nearby stars and measure the masses and orbits of the planets it finds. Survey 2000 nearby stars for planetary systems to learn whether our Solar System is unusual, or typical. Make a new catalog of star position 100 times more accurate than current measurements. Learn how our galaxy formed and will evolve by studying the dynamics of its stars. Critically test models of exactly how stars shine, including exotic objects like black holes, neutron stars and white dwarfs.

  7. A new MV bus transfer scheme for nuclear power plants

    International Nuclear Information System (INIS)

    Chang, C.K.

    2015-01-01

    The auxiliary power system of many generating stations consists of offsite power supply system and onsite power supply system, including emergency diesel generators (EDG) to provide secure power to auxiliary loads. If a normal power supply fails to supply power, then the power source is transferred to a standby power supply. In the case of nuclear power plants (NPP), the unit auxiliary transformer (UAT) and standby auxiliary transformer (SAT) - or station service transformer - are installed and powered from 2 offsite power circuits to meet regulatory requirements. The transfer methods of a motor bus from a normal source to a standby source used in power generating stations are fast bus transfer, in-phase transfer, or residual transfer. Fast bus transfer method is the most popular and residual voltage transfer method that is used as a backup in medium voltage buses in general. The use of the advanced technology like open circuit voltage prediction and digital signal processing algorithms can improve the reliability of fast transfer scheme. However, according to the survey results of the recent operation records in nuclear power plants, there were many instances where the fast transfer scheme has failed. To assure bus transfer in any conditions and circumstances, un-interruptible bus transfer scheme utilizing the state of the art medium voltage UPS (Un-interruptible Power Supply) is discussed and elaborated

  8. Bus network redesign for inner southeast suburbs of Melbourne, Australia

    Science.gov (United States)

    Pandangwati, S. T.; Milyanab, N. A.

    2017-06-01

    Public transport is the most effective mode of transport in the era of climate change and oil depletion. It can address climate change issues by reducing urban greenhouse gas emission and oil consumption while at the same time improving mobility. However, many public transport networks are not effective and instead create high operating costs with low frequencies and occupancy. Melbourne is one example of a metropolitan area that faces this problem. Even though the city has well-integrated train and tram networks, Melbourne’s bus network still needs to be improved. This study used network planning approach to redesign the bus network in the City of Glen Eira, a Local Government Area (LGA) in the southeastern part of Metropolitan Melbourne. The study area is the area between Gardenvale North and Oakleigh Station, as well as between Caulfield and Patterson Stations. This area needs network improvement mainly because of the meandering bus routes that run within it. This study aims to provide recommendations for improving the performance of bus services by reducing meandering routes, improving transfer point design and implementing coordinated timetables. The recommendations were formulated based on a ‘ready-made’ concept to increase bus occupancy. This approach can be implemented in other cities with similar problems and characteristics including those in Indonesia.

  9. Potential Influence of Metro on Bus: A Case Study

    Science.gov (United States)

    Selvakumar, M.; Abishek Reddy, M.; Sathish, V.; Venkatesh, R.

    2018-03-01

    A modal shift occurs when one mode of transport has a comparative advantage in a similar market over another. The present work concerns with the development of modal shift model for urban travel in Chennai, India. The modal shift model was calibrated using binary logit technique and validated using hold-out sample method. The validated model was used to predict the probability of shift in selected corridor. The recent introduction of metro rail in Chennai has lead to an increasing competition among public transport modes. To study the influence of metro on bus transport, a Stated Preference (SP) survey was conducted among express bus travellers. Using the SP survey data, a modal shift model was calibrated to estimate the plausible shift from bus to metro. Results indicate that variables like fare-difference, age, and income play an important role in the shift behaviour. When metro fare increases with respect to express bus fare, bus passengers are less willing to use metro and vice-versa.

  10. Determination of the Optimum Heat Transfer Coefficient and Temperature Rise Analysis for a Lithium-Ion Battery under the Conditions of Harbin City Bus Driving Cycles

    Directory of Open Access Journals (Sweden)

    Xiaogang Wu

    2017-10-01

    Full Text Available This study investigated the heat problems that occur during the operation of power batteries, especially thermal runaway, which usually take place in high temperature environments. The study was conducted on a ternary polymer lithium-ion battery. In addition, a lumped parameter thermal model was established to analyze the thermal behavior of the electric bus battery system under the operation conditions of the driving cycles of the Harbin city electric buses. Moreover, the quantitative relationship between the optimum heat transfer coefficient of the battery and the ambient temperature was investigated. The relationship between the temperature rise (Tr, the number of cycles (c, and the heat transfer coefficient (h under three Harbin bus cycles have been investigated at 30 °C, because it can provide a basis for the design of the battery thermal management system. The results indicated that the heat transfer coefficient that meets the requirements of the battery thermal management system is the cubic power function of the ambient temperature. Therefore, if the ambient temperature is 30 °C, the heat transfer coefficient should be at least 12 W/m2K in the regular bus lines, 22 W/m2K in the bus rapid transit lines, and 32 W/m2K in the suburban lines.

  11. Driving a Bus in India: A Study of Indore Bus Rapid Transport System

    Directory of Open Access Journals (Sweden)

    Siddhartha K. RASTOGI

    2017-12-01

    Full Text Available Indore is a typical tier-2 town in the central province of India, fast becoming a regional commercial hub in an economically booming state. The city has a population of over 2 million with no significant public transport. Among the multiple options available, the city started implementing a dedicated corridor based Bus Rapid Transport System (BRTS. The project was jointly mooted by the central, state, and city authorities. However, the system encountered a range of problems, including conflicts and pulls between multiple implementing agencies, delays in delivery of hardware and constructions, land acquisition and compensation, vested interests, public interest litigations, and court orders. The paper analyses the BRTS, introduced in Indore in the midst of 2013, from multiple party perspectives with an underlying search for public policy and public management insights. The broad results indicate feasibility and desirability of the project; however, real problems emerge in public and public perception management.

  12. Optimal Locations of Bus Stops Connecting Subways near Urban Intersections

    Directory of Open Access Journals (Sweden)

    Yuan Cui

    2015-01-01

    Full Text Available Unsuitable locations of bus stops which provide feeder transportation connecting subways near urban intersections usually lead to the low efficiency of public transport and level of passenger service. A multiobjective optimization model to distribute such stop locations is proposed to attain the shortest total walk distance of passengers and minimum delay time of cars through intersections and travel time of buses. The Pareto frontier and optimal solutions for the proposed model are given by the distance-based and enumerative methods. The Xizhimen bus stop is selected to implement case studies for verifying the validity of the proposed model. The analysis of sensitivity on possible solutions is also carried out in the case studies. The results show that the proposed model is capable of optimizing the locations of bus stops connecting subways near intersections and helpful to improve the level of passengers service and operational efficiency of public transportation.

  13. Rethinking passive transport: bus fare exemptions and young people's wellbeing.

    Science.gov (United States)

    Jones, Alasdair; Steinbach, Rebecca; Roberts, Helen; Goodman, Anna; Green, Judith

    2012-05-01

    Much recent public health research has emphasised the health impacts for young people of 'active travel' modes, typically defined as walking and cycling. Less research has focused on public transport modes. Drawing on qualitative data, we examine the links between bus travel and wellbeing in London, where young people currently have free bus travel. Our findings indicate that bus travel can be both a physically and socially active experience for young people. We suggest a more nuanced understanding of 'active travel' is now needed, alongside greater attention to urban public transport networks as key sites that impact on important determinants of wellbeing such as independent mobility and social inclusion. Copyright © 2012 Elsevier Ltd. All rights reserved.

  14. DESIGN OF CITY BUS LIFT FOR THE HANDICAPPEDS

    Directory of Open Access Journals (Sweden)

    K. Turgut GÜRSEL

    2003-03-01

    Full Text Available Although the technological developments, the handicappeds do not take part sufficiently in the social and economic life, because buildings, road construction features and means of the transport are not suitable for them. In this study, a lift for handicappeds was designed, that is supposed to be installed to the middle door of city buses. The lift, whose installation should require a few changes at the bus, is driven by a hydraulic system from the street to the level of the bus floor and vice-versa. In the work, at first a construction was developed in accordance with the dimensions of the middle door of a city bus. After determining of dimensions of all elements, a hydraulic mechanism was constructed, that raises the handicapped, its wheelchair and the platform. Furthermore the construction of the elements of the system were determined, and its proofs of strength analysis were indicated

  15. Spatial analysis of bus transport networks using network theory

    Science.gov (United States)

    Shanmukhappa, Tanuja; Ho, Ivan Wang-Hei; Tse, Chi Kong

    2018-07-01

    In this paper, we analyze the bus transport network (BTN) structure considering the spatial embedding of the network for three cities, namely, Hong Kong (HK), London (LD), and Bengaluru (BL). We propose a novel approach called supernode graph structuring for modeling the bus transport network. A static demand estimation procedure is proposed to assign the node weights by considering the points of interests (POIs) and the population distribution in the city over various localized zones. In addition, the end-to-end delay is proposed as a parameter to measure the topological efficiency of the bus networks instead of the shortest distance measure used in previous works. With the aid of supernode graph representation, important network parameters are analyzed for the directed, weighted and geo-referenced bus transport networks. It is observed that the supernode concept has significant advantage in analyzing the inherent topological behavior. For instance, the scale-free and small-world behavior becomes evident with supernode representation as compared to conventional or regular graph representation for the Hong Kong network. Significant improvement in clustering, reduction in path length, and increase in centrality values are observed in all the three networks with supernode representation. The correlation between topologically central nodes and the geographically central nodes reveals the interesting fact that the proposed static demand estimation method for assigning node weights aids in better identifying the geographically significant nodes in the network. The impact of these geographically significant nodes on the local traffic behavior is demonstrated by simulation using the SUMO (Simulation of Urban Mobility) tool which is also supported by real-world empirical data, and our results indicate that the traffic speed around a particular bus stop can reach a jammed state from a free flow state due to the presence of these geographically important nodes. A comparison

  16. Cost characteristics of tilt-rotor, conventional air and high speed rail short-haul intercity passenger service

    Science.gov (United States)

    Schoendorfer, David L.; Morlok, Edward K.

    1985-01-01

    The cost analysis done to support an assessment of the potential for a small tilt-rotor aircraft to operate in short-haul intercity passenger service is described in detail. Anticipated costs of tilt-rotor air service were compared to the costs of two alternatives: conventional air and high speed rail (HSR). Costs were developed for corridor service, varying key market characteristics including distance, passenger volumes, and minimum frequency standards. The resulting cost vs output information can then be used to compare modal costs for essentially identical service quality and passenger volume or for different service levels and volumes for each mode, as appropriate. Extensive sensitivity analyses are performed. The cost-output features of these technologies are compared. Tilt-rotor is very attractive compared to HSR in terms of costs over the entire range of volume. It also has costs not dramatically different from conventional air, but tilt-rotor costs are generally higher. Thus some of its other advantages, such as the VTOL capability, must offset the cost disadvantage for it to be a preferred or competitive mode in any given market. These issues are addressed in the companion report which considers strategies for tilt-rotor development in commercial air service.

  17. Lightweight power bus for a baseload nuclear reactor in space

    International Nuclear Information System (INIS)

    Oberly, C.E.; Massie, L.D.; Hoffman, D.J.

    1989-01-01

    Space environmental interactions with the power distribution/power processing subsystem can become a serious problem for power systems rated at 10's to 100's of kilowatts. Utilization of ceramic superconductors at 1000 A/cm/sup 2/, which has already been demonstrated at 77 K in a conductor configuration may eliminate both bus mass and distribution voltage problems in a high power satellite. The analytical results presented here demonstrate that a superconducting coaxial power transmission bus offers significant benefits in reduced distribution voltage and mass

  18. Quantum bus of metal nanoring with surface plasmon polaritons

    International Nuclear Information System (INIS)

    Lin Zhirong; Guo Guoping; Tu Tao; Li Haiou; Zou Changling; Ren Xifeng; Guo Guangcan; Chen Junxue; Lu Yonghua

    2010-01-01

    We develop an architecture for distributed quantum computation using quantum bus of plasmonic circuits and spin qubits in self-assembled quantum dots. Deterministic quantum gates between two distant spin qubits can be reached by using an adiabatic approach in which quantum dots couple with highly detuned plasmon modes in a metallic nanoring. Plasmonic quantum bus offers a robust and scalable platform for quantum optics experiments and the development of on-chip quantum networks composed of various quantum nodes, such as quantum dots, molecules, and nanoparticles.

  19. Overview of Multi-DC-Bus Solutions for DC Microgrids

    DEFF Research Database (Denmark)

    Ricchiuto, D.; Mastromauro, R.A.; Liserre, Marco

    2013-01-01

    DC Microgrids have recently received a lot of attention in the last years due to high penetration of renewable energy sources as well as distributed energy storage systems. In the future DC microgrids could be preferable respect to AC microgrids in terms of redundancy since multi-DC-Bus solutions...... could provide a continuative power supply to the loads. An overview of Multi-DC-Bus solutions is presented in this paper. The performances are compared on the basis of possible DC microgrid configurations, redundancy, different DC voltage levels....

  20. Bus bays inventory using a terrestrial laser scanning system

    Directory of Open Access Journals (Sweden)

    Bobkowska Katarzyna

    2017-01-01

    Full Text Available This article presents the use of laser scanning technology for the assessment of bus bay geo-location. Ground laser scanning is an effective tool for collecting three-dimensional data. Moreover, the analysis of a point cloud dataset can be a source of a lot of information. The authors have outlined an innovative use of data collection and analysis using the TLS regarding information on the flatness of bus bays. The results were finalized in the form of colour three-dimensional maps of deviations and pavement type.

  1. Black silicon with black bus-bar strings

    DEFF Research Database (Denmark)

    Davidsen, Rasmus Schmidt; Tang, Peter Torben; Mizushima, Io

    2016-01-01

    We present the combination of black silicon texturing and blackened bus-bar strings as a potential method for obtaining all-black solar panels, while using conventional, front-contacted solar cells. Black silicon was realized by mask-less reactive ion etching resulting in total, average reflectance...... below 0.5% across a 156x156 mm2 silicon wafer. Black bus-bars were realized by oxidized copper resulting in reflectance below 3% in the entire visible wavelength range. The combination of these two technologies may result in aesthetic, all-black panels based on conventional, front-contacted solar cells...

  2. Design of temperature monitoring system based on CAN bus

    Science.gov (United States)

    Zhang, Li

    2017-10-01

    The remote temperature monitoring system based on the Controller Area Network (CAN) bus is designed to collect the multi-node remote temperature. By using the STM32F103 as main controller and multiple DS18B20s as temperature sensors, the system achieves a master-slave node data acquisition and transmission based on the CAN bus protocol. And making use of the serial port communication technology to communicate with the host computer, the system achieves the function of remote temperature storage, historical data show and the temperature waveform display.

  3. Digital transmitter for data bus communications system

    Science.gov (United States)

    Proch, G. E. (Inventor)

    1975-01-01

    An improved digital transmitter for transmitting serial pulse code modulation (pcm) data at high bit rates over a transmission line is disclosed. When not transmitting, the transmitter features a high output impedance which prevents the transmitter from loading the transmission line. The pcm input is supplied to a logic control circuit which produces two discrete logic level signals which are supplied to an amplifier. The amplifier, which is transformer coupled to the output isolation circuitry, converts the discrete logic level signals to two high current level, ground isolated signals in the secondary windings of the coupling transformer. The latter signals are employed as inputs to the isolation circuitry which includes two series transistor pairs operating into a hybrid transformer functioning to isolate the transmitter circuitry from the transmission line.

  4. Line outage contingency analysis including the system islanding ...

    African Journals Online (AJOL)

    The optimally ordered sparse [Bʹ], [Bʺ] matrices for the integrated system are used for load flow analysis to determine modified values of voltage phase angles [d] and bus voltages [V] to determine the over loading effect on the remaining lines due to outage of a selected line outage contingency. In case of over loading in ...

  5. Evaluation of Urban Bus Transport Failure in Gujranwala City of Pakistan

    OpenAIRE

    MUHAMMAD WAQAR ASLAM; ZAHARA BATOOL

    2017-01-01

    This research work has evaluated the performance of urban public bus transport service operating in Gujranwala city of Pakistan. The assessment has been made in terms of financial viability, bus condition, operational performance and user perception. Based on the data requirements, various traffic/transport surveys were conducted including Passenger Boarding and Alighting Survey, Bus Count Survey, Bus Inspection Survey, Illegal Operations Survey and Public Transport User Interview Survey in c...

  6. Active Power Filter DC Bus Voltage Piecewise Reaching Law Variable Structure Control

    OpenAIRE

    Liu, Baolian; Ding, Zujun; Zhao, Huanyu; Jin, Defei

    2014-01-01

    The DC bus voltage stability control is one key technology to ensure that Active Power Filter (APF) operates stably. The external disturbances such as power grid and load fluctuation and the system parameters changing may affect the stability of APF DC bus voltage and the normal operation of APF. The mathematical model of DC bus voltage is established according to power balance principle and a DC bus voltage piecewise reaching law variable structure control algorithm is proposed to solve the ...

  7. Kajian Keamanan Pengoperasian Public Transport Tinjauan Terhadap Kekuatan Rangka Body Bus

    OpenAIRE

    Sudiro, B. M

    2010-01-01

    In order to meet the safety and security of the public transportation, design specification of construction body bus or bus frame structures should have an appropriate structural strength and comply with standard design including the safety factor and selection of material besides static and dynamic testing of the part of body bus. It is also realized that a bus carrying passengers have to give secure to the passengers also driver.The fact that a technology concerning with metal works indus...

  8. Developing a viable electric bus service: the Milton Keynes demonstration project

    OpenAIRE

    Miles, John; Potter, Stephen

    2014-01-01

    Buses can be a serious source of city centre air pollution. Electric buses deliver zero emissions but, because of the time required to recharge, more buses are needed for a given timetable than diesel counterparts, so making mainstream electric bus operations prohibitively expensive.\\ud \\ud Early 2014 saw the implementation in Milton Keynes of an electric bus service designed to overcome this problem. An entire bus route has been converted to electric operation with inductive charging at bus ...

  9. DETERMINATION OF THE DELAY DEPARTURE TIME OF THE BUS FROM STOPPING POINT INTO THE CAR FLOW

    Directory of Open Access Journals (Sweden)

    P. Gorbachov

    2014-10-01

    Full Text Available An analytical model for estimation of the bus departure delax from the bus stopping point after passenger loading is presented. The model allows to take into account the traffic density on a particular road section of the transport network, as well as the bus parameters.

  10. Computer-Based Video Instruction to Teach Students with Intellectual Disabilities to Use Public Bus Transportation

    Science.gov (United States)

    Mechling, Linda; O'Brien, Eileen

    2010-01-01

    This study investigated the effectiveness of computer-based video instruction (CBVI) to teach three young adults with moderate intellectual disabilities to push a "request to stop bus signal" and exit a city bus in response to target landmarks. A multiple probe design across three students and one bus route was used to evaluate effectiveness of…

  11. 49 CFR 383.123 - Requirements for a school bus endorsement.

    Science.gov (United States)

    2010-10-01

    ... devices required for school buses by State or Federal law or regulation. (ii) Emergency exits and... 49 Transportation 5 2010-10-01 2010-10-01 false Requirements for a school bus endorsement. 383.123... Requirements for a school bus endorsement. (a) An applicant for a school bus endorsement must satisfy the...

  12. The Role of the Coroner in School Bus Accident Prevention: Some Recommendations.

    Science.gov (United States)

    Fox, Michael

    1995-01-01

    Following the deaths of two elementary school students in bus-related accidents in 1992, the Coroner of Quebec held extensive hearings investigating school bus safety and accident prevention. A subsequent report addressed responsibilities of government and school board officials to correct deficiencies in school bus services and provided…

  13. School Bus Safety: What Can Our Schools Do to Protect Our Children?

    Science.gov (United States)

    Dargan, Thomas J.; Silverstone, Adam H.

    2014-01-01

    School districts and school bus contractors are entrusted with the most important of all road users--our nation's children. In the wake of recent newsworthy accidents and attention grabbing headlines regarding unfit bus drivers, claims premised upon school bus accidents have become increasingly tangential and, in turn, personal injury attorneys…

  14. O valor de um intercâmbio: mobilidade estudantil brasileira, bilateralismo & internacionalização da educação. The value of an intercâmbio: brazilian student mobility, bilateralism & international education

    Directory of Open Access Journals (Sweden)

    Eric Spears

    2014-05-01

    Full Text Available Brazil’s emergence in the global economy as a member of the BRIC (Brazil, Russia, Índia, China, and South Africa states has prompted the federal government to establish the Brazilian Scientific Mobility Program (Science Without Borders in order to advance the country’s social capital and infrastructure in STEM (Science, Technology, Engineering, and Math related disciplines and industries. Public and private investment in the Scientific Mobility Program has transformed the way in which Brazilian government, universities, and citizenry places value the intercâmbio (student exchange experience in the United States. STEM-related disciplines are now disproportionately funded versus social sciences, humanities, and fine arts fields. This development has altered the way in which student mobility in the United States is given worth and changed the trajectory of international education in Brazil. This research provides a conceptual analysis of the Brazilian Scientific Mobility Program by using a critical political economy perspective. The essay conceptualizes the Science without Borders initiative at global, national, and local levels. This research also explores what implications the bilateral U.S.-Brazil Educational Partnership may have on future policy, practice, and ultimately, funding of Brazilian student mobility. A emergência do Brasil no âmbito da economia mundializada como participante do BRIC (Brasil, Rússia, Índia, China e África do Sul mobilizou o governo federal brasileiro a estabelecer um programa estatal de mobilidade acadêmica (Programa Ciência sem Fronteiras de modo a fazer avançar o capital social do país (general intellect e a infraestrutura em STEM (Ciência, Tecnologia, Engenharia e Matemática relacionadas à indústria. Investimentos públicos e privados no programa de mobilidade acadêmica transformaram o modo como o governo brasileiro e as universidades valorizam o intercâmbio estudantil com os Estados Unidos. As

  15. Old-Fashioned Bus Trips: New Age Professional Development

    Science.gov (United States)

    Feldhues, Katherine; Epley, Hannah K.

    2018-01-01

    Two 4-H Camp-related bus tours offered new nontraditional professional development (PD) experiences that better align Extension's PD opportunities with the organization's experiential education pedagogy. Creating quality PD opportunities for employees is important because such experiences can affect overall work performance, community connections,…

  16. Analyzing injury severity of bus passengers with different movements.

    Science.gov (United States)

    Li, Duo; Zhao, Yifei; Bai, Qiang; Zhou, Bei; Ling, Hongbiao

    2017-07-04

    Though public transport vehicles are rarely involved in mass casualty accidents, when they are, the number of injuries and fatalities is usually high due to the high passenger capacity. Of the few studies that have been conducted on bus safety, the majority focused on vehicle safety features, road environmental factors, as well as driver characteristics. Nevertheless, few studies have attempted to investigate the underlying risk factors related to bus occupants. This article presents an investigation aimed at identifying the risk factors affecting injury severity of bus passengers with different movements. Three different passenger movement types including standing, seated, and boarding/alighting were analyzed individually using classification and regression tree (CART) method based on publicly available accident database of Great Britain. According to the results of exploratory analyses, passenger age and vehicle maneuver are associated with passenger injury severity in all 3 types of accidents. Moreover, the variable "skidding and overturning" is associated with injury severity of seated passengers and driver age is correlated with injury severity of standing and boarding/alighting passengers. The CART method shows its ability to identify and easily explain the complicated patterns affecting passenger injury severity. Several countermeasures to reduce bus passenger injury severity are recommended.

  17. A Quantitative Economics Of Seasonality In Bus Patronage In Nigeria

    African Journals Online (AJOL)

    Seasonal variation is a well-known phenomenon, in many endeavrous and enterprises. Passenger of patronage of road transportation by bus is generally implicated as exhibiting excessive seasonality. The study thus set out to empirically investigate the myth or reality of the thesis that trip generation and trip attraction can ...

  18. Aerodynamic study of state transport bus using computational fluid dynamics

    Science.gov (United States)

    Kanekar, Siddhesh; Thakre, Prashant; Rajkumar, E.

    2017-11-01

    The main purpose of this study was to develop the aerodynamic study of a Maharashtra state road transport bus. The rising fuel price and strict government regulations makes the road transport uneconomical now days. With the objective of increasing fuel efficiency and reducing the emission of harmful exhaust gases. It has been proven experimentally that vehicle consumes almost 40% of the available useful engine power to overcome the drag resistance. This provides us a huge scope to study the influence of aerodynamic drag. The initial of the project was to identify the drag coefficient of the existing ordinary type model called “Parivartan” from ANSYS fluent. After preliminary analysis of the existing model corresponding changes are made in such a way that their implementation should be possible at workshop level. The simulation of the air flow over the bus was performed in two steps: design on SolidWorks CAD and ANSYS (FLUENT) is used as a virtual analysis tool to estimate the drag coefficient of the bus. We have used the turbulence models k-ε Realizable having a better approximation of the actual result. Around 28% improvement in the drag coefficient is achieved by CFD driven changes in the bus design. Coefficient of drag is improved by 28% and fuel efficiency increased by 20% by CFD driven changes.

  19. Bus-oriented digital control techniques in nuclear power plants

    International Nuclear Information System (INIS)

    Salm, M.

    1987-01-01

    The author states the conservative principles which govern the authorization procedures for nuclear reactor control systems. Using the example of a feedwater supply regulator, employing a digital, bus-oriented control system, he describes how the stigma attached to the word nuclear can be alleviated. (G.T.H.)

  20. Energy efficient motion control of the electric bus on route

    Science.gov (United States)

    Kotiev, G. O.; Butarovich, D. O.; Kositsyn, B. B.

    2018-02-01

    At present, the urgent problem is the reduction of energy costs of urban motor transport. The article proposes a method of solving this problem by developing an energy-efficient law governing the movement of an electric bus along a city route. To solve this problem, an algorithm is developed based on the dynamic programming method. The proposed method allows you to take into account the constraints imposed on the phase coordinates, control action, as well as on the time of the route. In the course of solving the problem, the model of rectilinear motion of an electric bus on a horizontal reference surface is considered, taking into account the assumptions that allow it to be adapted for the implementation of the method. For the formation of a control action in the equations of motion dynamics, an algorithm for changing the traction / braking torque on the wheels of an electric bus is considered, depending on the magnitude of the control parameter and the speed of motion. An optimal phase trajectory was obtained on a selected section of the road for the prototype of an electric bus. The article presents the comparison of simulation results obtained with the optimal energy efficient control law with the results obtained by a test driver. The comparison proved feasibility of the energy efficient control law for the automobile city electric transport.

  1. Economic impacts of bus rapid transit in southeast Michigan.

    Science.gov (United States)

    2015-12-01

    In recent years, Bus Rapid Transit (BRT) has generated great interest across the United States. There are more than 20 BRT : systems in existence, and more are in the planning stage (including in Detroit). Within the next few years, BRT will be plann...

  2. Improving School Bus Safety. Transportation Research Board Special Report 222.

    Science.gov (United States)

    National Academy of Sciences - National Research Council, Washington, DC. Transportation Research Board.

    While school buses transport more passengers per trip, the rate of occupant fatalities per mile driven for school buses is one-quarter that for passenger cars. Nevertheless, the public expects school districts and other school bus operators to take all reasonable precautions to protect children as they travel to and from school. Although a variety…

  3. Implementation of a Walking School Bus: Lessons Learned

    Science.gov (United States)

    Kong, Alberta S.; Sussman, Andrew L.; Negrete, Sylvia; Patterson, Nissa; Mittleman, Rachel; Hough, Richard

    2009-01-01

    Background: Obesity is rapidly becoming the most common chronic medical condition affecting children. To address this crisis, an Albuquerque, New Mexico, elementary school partnered with University of New Mexico researchers and conducted a Walking School Bus (WSB). The purpose of this article is to examine the feasibility of implementing a WSB.…

  4. Optical bus of centralized relay protection and automation system of ...

    African Journals Online (AJOL)

    The article deals with the system of information collection and transfer from a centralized relay protection and automation system for medium voltage electrical units based on a passive optical bus. The issues of electromagnetic compatibility of technical devices are also considered, and the intensity of electromagnetic ...

  5. A Novel Time Synchronization Method for Dynamic Reconfigurable Bus

    Directory of Open Access Journals (Sweden)

    Zhang Weigong

    2016-01-01

    Full Text Available UM-BUS is a novel dynamically reconfigurable high-speed serial bus for embedded systems. It can achieve fault tolerance by detecting the channel status in real time and reconfigure dynamically at run-time. The bus supports direct interconnections between up to eight master nodes and multiple slave nodes. In order to solve the time synchronization problem among master nodes, this paper proposes a novel time synchronization method, which can meet the requirement of time precision in UM-BUS. In this proposed method, time is firstly broadcasted through time broadcast packets. Then, the transmission delay and time deviations via three handshakes during link self-checking and channel detection can be worked out referring to the IEEE 1588 protocol. Thereby, each node calibrates its own time according to the broadcasted time. The proposed method has been proved to meet the requirement of real-time time synchronization. The experimental results show that the synchronous precision can achieve a bias less than 20 ns.

  6. Bussikontsern Go Bus ihaldab Harjumaa turgu / Signe Kalberg

    Index Scriptorium Estoniae

    Kalberg, Signe, 1959-

    2005-01-01

    AS-i Tarbus ja kaheksa bussiettevõtte ühinemisel moodustati AS Go Bus, ettevõte plaanib veel mitme bussifirma liitmist. Atko Grupi juhatuse esimehe Margo Tomingase, AS Sebe nõukogu esimehe Hugo Osula arvamus. Lisa: Konkurentsiamet hoiab silma peal

  7. Spanish version of Bus Drivers' Job Demands Scale (BDJD-24).

    Science.gov (United States)

    Boada-Grau, Joan; Prizmic-Kuzmica, Aldo-Javier; González-Fernández, Marcos-David; Vigil-Colet, Andreu

    2013-01-01

    Karasek and Theorell's Job Demands-Control Model argues that adverse health-related outcomes, both psychological and physiological, arise from a combination of high job demand and a low level of job control. The objective was to adapt Meijman and Kompier's Bus Drivers' Job Demands Scale (BDJD-24), which enables us to assess the job demands of bus drivers, to Spanish. The final version of the Spanish adaptation was applied to a sample made up of 287 bus drivers living in Spain (80.1% men and 19.9% women), whose average age was 40.44 (SD= 11.78). The results yielded a three-factor structure for the scale used: Time Pressure, Safety, and Passengers. These findings confirm that the Spanish version replicates the factor structure of the original English scale. The reliability of the three subscales was acceptable, ranging from .75 to .84. Furthermore, the subscales were also related to different external correlates and to other scales and showed good convergent and criterion validity. The present instrument can be used to evaluate job demands of bus drivers, as its psychometrics are substantially sound.

  8. High-Tech School Bus Teaches Students on the Road

    Science.gov (United States)

    Katims, Lauren

    2011-01-01

    Last year, kindergarten through high school students in the rural Hector, Arkansas, School District barely had the technology resources that keep kids interested in math and science. This year, they potentially have the most advanced resources in the country--before they even step into the classroom. One school bus in Arkansas' Pope County has…

  9. Measuring Bus Drivers' Occupational Stress Under Changing Working Conditions

    NARCIS (Netherlands)

    Hlotova, Y.; Cats, O.; Meijer, S.A.

    2014-01-01

    Stress is an immense problem in modern society; approximately half of all occupational illnesses are directly or indirectly related to stress. The work of a bus driver is typically associated with high stress levels that negatively influence individual well-being as well as workforce management. The

  10. Steering characteristic of an articulated bus under quasi steady maneuvering

    Science.gov (United States)

    Ubaidillah, Setiawan, Budi Agus; Aridharma, Airlangga Putra; Lenggana, Bhre Wangsa; Caesar, Bernardus Placenta Previo

    2018-02-01

    Articulated buses have been being preferred as public transportation modes due to their operational capacity. Therefore, passenger safety must be the priority of this public service vehicle. This research focused on the analytical approach of steering characteristics of an articulated bus when it maneuvered steadily. Such turning condition could be referred as a stability parameter of the bus for preliminary handling assessment. The analytical approach employed kinematics relationship between front and rear bodies as well as steering capabilities. The quasi steady model was developed to determine steering parameters such as turning radius, oversteer, and understeer. The mathematical model was useful for determining both coefficients of understeer and oversteer. The dimension of articulated bus followed a commonly used bus as utilized in Trans Jakarta busses. Based on the simulation, for one minimum center of the body, the turning radius was calculated about 8.8 m and 7.6 m at steady turning speed of 10 km/h. In neutral condition, the minimum road radius should be 6.5 m at 10 km/h and 6.9 m at 40 km/h. For two centers of the body and oversteer condition, the front body has the turning radius of 8.8 m, while, the rear body has the turning radius of 9.8 m at both turning speeds of 40 km/h. The other steering parameters were discussed accordingly.

  11. GeoBus: sharing science research with schools

    Science.gov (United States)

    Roper, Kathryn; Robinson, Ruth; Moorhouse, Ben

    2016-04-01

    GeoBus (www.geobus.org.uk) is an educational outreach project that was developed in 2012 by the Department of Earth and Environmental Sciences at the University of St Andrews, and it is currently sponsored by industry, NERC, The Crown Estate, and the Scottish Government. The aims of GeoBus are to support the teaching of Earth Science in secondary (middle and high) schools by providing teaching support to schools that have little or no experience in teaching this subject. This is, in part, done through the sharing of new science research outcomes and the experiences of young researchers with school pupils to provide a bridge between industry, higher education institutions, research councils and schools. Since its launch, over 40,000 pupils will have been involved in experiential Earth science learning activities in 190 different schools (over 400 separate visits) across the length and breadth of Scotland: many of these schools are in remote and disadvantaged regions. A new GeoBus project is under development within the Department of Earth Sciences at UCL in London. A key aim of GeoBus is to incorporate new research into our workshops with the main challenge being the development of appropriate resources that incorporate the key learning aims and requirements of the science and geography curricula. GeoBus works closely with researchers, teachers and educational practitioners to tailor the research outcomes to the curricula as much as possible. Over the past four years, GeoBus has developed 17 workshops, 5 challenge events and extensive field trips and each of these activities are trialled and evaluated within the university, and adjustments are made before the activities are delivered in schools. Activities are continually reviewed and further developments are made in response to both teacher and pupil feedback. This critical reflection of the project's success and impact is important to insure a positive and significant contribution to the science learning in

  12. Real life testing of a Hybrid PEM Fuel Cell Bus

    Science.gov (United States)

    Folkesson, Anders; Andersson, Christian; Alvfors, Per; Alaküla, Mats; Overgaard, Lars

    Fuel cells produce low quantities of local emissions, if any, and are therefore one of the most promising alternatives to internal combustion engines as the main power source in future vehicles. It is likely that urban buses will be among the first commercial applications for fuel cells in vehicles. This is due to the fact that urban buses are highly visible for the public, they contribute significantly to air pollution in urban areas, they have small limitations in weight and volume and fuelling is handled via a centralised infrastructure. Results and experiences from real life measurements of energy flows in a Scania Hybrid PEM Fuel Cell Concept Bus are presented in this paper. The tests consist of measurements during several standard duty cycles. The efficiency of the fuel cell system and of the complete vehicle are presented and discussed. The net efficiency of the fuel cell system was approximately 40% and the fuel consumption of the concept bus is between 42 and 48% lower compared to a standard Scania bus. Energy recovery by regenerative braking saves up 28% energy. Bus subsystems such as the pneumatic system for door opening, suspension and brakes, the hydraulic power steering, the 24 V grid, the water pump and the cooling fans consume approximately 7% of the energy in the fuel input or 17% of the net power output from the fuel cell system. The bus was built by a number of companies in a project partly financed by the European Commission's Joule programme. The comprehensive testing is partly financed by the Swedish programme "Den Gröna Bilen" (The Green Car). A 50 kW el fuel cell system is the power source and a high voltage battery pack works as an energy buffer and power booster. The fuel, compressed hydrogen, is stored in two high-pressure stainless steel vessels mounted on the roof of the bus. The bus has a series hybrid electric driveline with wheel hub motors with a maximum power of 100 kW. Hybrid Fuel Cell Buses have a big potential, but there are

  13. Characterisation of an urban bus network for environmental purposes.

    Science.gov (United States)

    André, Michel; Villanova, André

    2004-12-01

    Since pollutant emissions are closely related to the operating conditions of vehicles, their evaluation usually involves studying these operating conditions (through bus instrumentation and monitoring under actual operation), the design of representative driving or engine test cycles and the measurement of pollutant emissions. A preliminary characterisation of the routes on a bus network should make it possible to identify typical routes, the driving conditions and pollutant emissions of which are then studied. Two approaches are envisaged and applied to the Paris area, for which a wealth of information is available, which should be transferable to other bus networks. Both approaches are based on factorial analysis and automatic clustering, to allow optimum description and the identification of a pertinent typology of the bus routes in several classes. The first attempt at characterisation is based on statistics relating to bus operations: route characteristics (length, dedicated bus lanes, number of stops, location of stops: schools, tourist sites, hospitals, railways or underground stations), travel time, commercial speed, annual statistics (number of passengers, number of vehicles per hour, total kilometres), the irregularity of travel (variation of travel times, injuries, congestion.), as well as information on the problems encountered (congestion, distribution of the passenger load, junctions, bends). A second approach is based on the analysis of the "urban context" in which buses are driven. Population, employment, housing, road network, traffic and places that generate or disturb traffic (schools, railway stations, shopping areas, etc.) are calculated for the Ile de France region, by cells of 100 x 100 m, and collected in a geographical information system (GIS). Statistical analyses enable a typology of these urban cells to be established, the main parameters being density, type of housing, road types and traffic levels. The bus routes are then analysed

  14. THE PREVALENCE OF MUSCULOSKELETAL DISORDERS AMONG BUS DRIVERS IN TRICITY

    Directory of Open Access Journals (Sweden)

    Lalit

    2015-10-01

    Full Text Available Background: Musculoskeletal disorders are widespread in many countries around the world. It has been reported that about 58 percent of the world's population over the age of 10 years spent one third of their life span at work. The population at a high risk include nursing facilities, transportation, mining, food processing, leather tanning, heavy and light manufacturing. Transport workers have been found to be at high risk of developing work related musculoskeletal disorders (WRMSDs. There has been literature evidence regarding the prevalence of musculoskeletal disorders in bus drivers of various cities of different countries. But no study has been done so far in Tricity (Chandigarh, Panchkula and Mohali for the same. The purpose of this study is to investigate the prevalence and characteristics of work related musculoskeletal disorders (WRMSDs among bus drivers of Tricity. Methods: 300 bus drivers were included in the study according to the inclusion and exclusion criteria. The standardized Nordic questionnaire for musculoskeletal disorder and a self administered questionnaire were filled by therapist after the personal interview of each driver. Results: Unpaired t test was used to measure the difference in variable of two groups and Karl Pearson’s correlation coefficient was used to determine the correlation between two entities. In the present study, the subjects were in the age group of 25 to 50 years. Out of the total sample of 300 male bus drivers in Tricity, 159 reported that they had WRMSDs. The prevalence of WRMSDs among bus drivers in Tricity was 53%. In present study, the prevalence of low back pain was highest among the bus drivers that are 30.3%, then neck pain 17.3%, knee pain 14.7%, shoulder 6.3%, ankle and feet 5.7%, upper back 4%, hip and thigh 4%, elbow 1.3% and wrist and hand 1.3%. Thus low back pain, neck pain and knee pain are the most prevalent WRMSDs amongst bus drivers. Conclusions: Work-related biomechanical

  15. Optimal bus temperature for thermal comfort during a cool day.

    Science.gov (United States)

    Velt, K B; Daanen, H A M

    2017-07-01

    A challenge for electric buses is to minimize heating and cooling power to maximally extend the driving range, but still provide sufficient thermal comfort for the driver and passengers. Therefore, we investigated the thermal sensation (TS) and thermal comfort (TC) of passengers in buses during a cool day (temperature 13.4 ± 0.5 °C, relative humidity (RH) 60 ± 5.8%) typical for the Dutch temperate maritime climate. 28 Males and 72 females rated TS and TC and gave information on age, stature, body weight and worn garments. The temperature in the bus of 22.5 ± 1.1 °C and RH of 59.9 ± 5.8% corresponded to a slightly warm feeling (TS = 0.85 ± 1.06) and TC of 0.39 ± 0.65. TS related significantly to bus temperature, clothing insulation and age. Linear regression based on these parameters showed that the temperature in the bus corresponding to TC = 0 and TS = 0 would have been 20.9 ± 0.6 °C. In conclusion, a 1.6 °C lower bus temperature during the investigated cool day probably would have led to less thermal discomfort and energy savings of electrical busses. The methodology to relate climatic measurements to subjective assessments is currently employed in a wider climatic range and may prove to be useful to find a better balance between thermal comfort and energy savings of the bus. Copyright © 2017 Elsevier Ltd. All rights reserved.

  16. Concentrations of polycyclic aromatic hydrocarbons in resuspendable fraction of settled bus dust and its implications for human exposure

    International Nuclear Information System (INIS)

    Gao, Peng; Liu, Sa; Feng, Yujie; Lin, Nan; Lu, Binyu; Zhang, Zhaohan; Cui, Fuyi; Xing, Baoshan; Hammond, S. Katharine

    2015-01-01

    This preliminary study measured Polycyclic Aromatic Hydrocarbons (PAHs) concentrations in the resuspendable fraction of settled dust on 39 bus lines, to evaluate the impact of engine type (gasoline and compressed natural gas) on exposure for commuters and drivers. Benzo(b)fluoranthene(BbF) was the predominant PAH in resuspendable fraction of settled bus dust. The concentration of total PAHs was 92.90 ± 116.00 μg/g (range: 0.57–410) in gasoline buses and 3.97 ± 1.81 (range: 2.01–9.47) in compressed natural gas (CNG) buses. Based on Benzo[a]pyrene (BaP) equivalent concentrations for the sum of 16 PAHs, the average daily dose (ADD) via dust ingestion and dermal contact was calculated. The ADD of PAHs was higher for commuters and drivers in gasoline-powered buses than in buses using CNG buses. For both short and long duration journeys, young commuters were exposed to higher levels of PAHs via dust ingestion and dermal contact than adult commuters. - Highlights: • Resuspendable fraction of settled dust from microenvironment of buses in Harbin monitored for PAHs exposure assessment. • Higher levels of PAHs pollutants at gasoline-powered buses than at compressed natural gas-powered buses. • Non-occupational and occupational exposures in the microenvironment of buses are assessed. - Occupational and non-occupational exposure to PAHs from the microenvironment of bus

  17. Retrofitting bus fleet for natural gas operation

    International Nuclear Information System (INIS)

    Stella, E.; Foresti, P.

    1992-01-01

    Buses, operating within a Florence (Italy) municipal transportation system, and equipped with Otto cycle engines, were selected for retrofitting taking into account the suitability of each vehicle's specific routing and service requirements. Cost benefit analyses indicated that it wouldn't be economically feasible to retrofit buses equipped with diesel engines. A computerized refuelling system was set up at the fleet's central service station which was hooked up to the natural gas utility's supply line. This paper tables the cost benefit analysis data comparing gasoline and methane operation and reflecting the cost savings which are expected to be accrued through this methanization program over a span of 14 years

  18. Rancang Bangun Sistem Pemesanan Tiket Bus Kupang-Atambua Berbasis SMS Gateway

    Directory of Open Access Journals (Sweden)

    Emerensiana Ngaga

    2016-11-01

    Full Text Available Bus merupakan alat transportasi yang paling banyak digunakan masyarakat karena harga yang murah dan masih terjangkau untuk masyarakat kalangan ekonomi menengah ke bawah.  Umumnya pemesanan tiket bus dilakukan dengan mendatangi langsung tempat penjualan tiket bus atau dengan cara menelepon ke kantor agen. Proses pemesanan seperti ini  memiliki kekurangan dimana pegawai kerepotan dalam mencatat dan seringkali terjadi kesalahan dalam mencatat pemesanan tiket. Sedangkan untuk waktu pemesanan, umumnya calon penumpang melakukan pemesanan tiket, satu atau dua hari sebelum keberangkatan dan ada juga yang tidak sempat memesan tiket beberapa hari sebelumnya dan melakukan pembelian tiket pada hari keberangkatan sehingga sering kali tidak mendapatkan tiket. Penelitian ini bertujuan merancang bangun sistem pemesanan tiket bus berbasis SMS Gateway yang memberikan kemudahan layanan pemesanan tiket bus bagi masyarakat secara jarak jauh serta kemudahan mengetahui informasi penjadwalan bus dengan cepat. Aplikasi dibangun menggunakan metode Unified Process, dengan bahasa pemrograman Java NetBeansIDE 7.3.1, MySQL sebagai database dan Gammu sebagai software untuk membantu pembangunan aplikasi SMS Gateway. Hasil dari penelitian ini adalah sebuah sistem pemesanan tiket bus yang memberikan alternatif baru proses pemesanan tiket bus secara baik tanpa ada permasalahan jarak dan waktu. Selain itu masyarakat juga dapat mengetahui informasi jadwal bus, harga tiket dan juga informasi bila terjadi perubahan jadwal keberangkatan bus.   Kata kunci— Bus, Tiket, SMS Gateway, Unified Process

  19. Estereótipos na comunicação intercultural: o caso do intercâmbio cultural na PUCRS

    OpenAIRE

    Espindola, Polianne Merie

    2010-01-01

    Este é um estudo da estereotipia existente na comunicação intercultural. O objetivo é entender a natureza do estereótipo mental e seu papel na comunicação entre interlocutores de culturas distintas. Para tanto, observa os estudantes estrangeiros em programas de intercâmbio no campus da Pontifícia Universidade Católica do Rio Grande do Sul. O estudo define o conceito de estereótipo e explicita seu papel na comunicação intercultural; verifica sua relevância na construção das narrativas entre cu...

  20. O intercâmbio de hospitalidade e a sua influência nos jovens viajantes: o caso do Couchsurfing na cidade do Porto

    OpenAIRE

    Tootill, Isabel Cunha

    2017-01-01

    Os meios de comunicação têm, ao longo das últimas décadas, sofrido vastas alterações devido aos acelerados desenvolvimentos tecnológicos, resultando numa profunda transformação da natureza dos relacionamentos humanos. A evolução de plataformas online, nomeadamente de redes sociais online, tem contribuído neste sentido, incitando a partilha de conteúdos, a colaboração, a comunicação e o desenvolvimento relacional entre utilizadores. Neste sentido, o intercâmbio de hospitalidade ...

  1. A study of an arbiter function in the structures of a shared bus

    Science.gov (United States)

    Seck, J.-P.

    The results of a comparative study of synchronous and asynchronous arbiters for managing user access to a shared bus is presented. The best available method is determined to be modular arbiter structures attached only to the decision module. Linear and circular arbitration strategies are examined for suitability for automatic decision-making. A multiple strategies arbiter scheme is devised, involving the superposition of various strategies of one sequential machine into another. It is then possible to modify the strategy on-line if the current strategy is ineffective. The utilization of a multiple structure of cascading arbiter devices is noted to be effective if response time is not a critical matter. Finally, attention is given to automatic circuit testing and fault detection. An example is furnished in terms of a management system for a shared memory in a multimicroprocessor structure.

  2. Lessons Learned in High Frequency Data Transmission Design: ATLAS Strips Bus Tape

    CERN Document Server

    AUTHOR|(INSPIRE)INSPIRE-00213647; The ATLAS collaboration; Fadeyev, Vitaliy; Grillo, Alexander; Martinez-McKinney, George Forest; Phillips, Peter William; Sawyer, Craig; Sullivan, Stephanie W; Wastie, Roy; Weidberg, Anthony; Nielsen, Jason

    2017-01-01

    Requirements of HEP experiments lead to highly integrated systems with many electrical, mechanical and thermal constraints. A complex performance optimisation is therefore required. High speed data transmission lines are designed using copper-polyimide flexible bus tapes rather than cable harnesses to minimize radiation length. Methods to improve the signal integrity of point-to-point links and multi-drop configurations in an ultra-low-mass system are described. FEA calculations are an essential guide to the optimisation which allow data rates of 640 Mbps for point-to-point links over a length of up to 1.4m, as well as 160 Mbps for multi-drop configuration. The designs were validated using laboratory measurements of S-parameters and direct BER tests.

  3. Electrical engineering unit for the reactive power control of the load bus at the voltage instability

    Science.gov (United States)

    Kotenev, A. V.; Kotenev, V. I.; Kochetkov, V. V.; Elkin, D. A.

    2018-01-01

    For the purpose of reactive power control error reduction and decrease of the voltage sags in the electric power system caused by the asynchronous motors started the mathematical model of the load bus was developed. The model was built up of the sub-models of the following elements: a transformer, a transmission line, a synchronous and an asynchronous loads and a capacitor bank load, and represents the automatic reactive power control system taking into account electromagnetic processes of the asynchronous motors started and reactive power changing of the electric power system elements caused by the voltage fluctuation. The active power/time and reactive power/time characteristics based on the recommended procedure of the equivalent electric circuit parameters calculation were obtained. The derived automatic reactive power control system was shown to eliminate the voltage sags in the electric power system caused by the asynchronous motors started.

  4. Compliance with driver's license laws and illegal licensing among commercial bus drivers in Lagos, Nigeria: policy implications and evidence for action.

    Science.gov (United States)

    Okafor, I P; Odeyemi, K A; Dolapo, D C; Adegbola, A A

    2014-09-01

    To determine the level of compliance with driver's license laws among commercial bus drivers in Lagos, Nigeria. Two intercity motor parks were selected by simple random sampling and all consenting minibus drivers participated in the study. Key Informant Interviews (KIIs) were also conducted with selected officials in the driver training and licensing authorities. Compliance with the minimum age for driving was high (93.6%), so also was having driving test prior to driver's license procurement (83.3%). Formal driver training and VA testing were very low, (26.1% and 32.9% respectively) Overall, only 9.3% of them were found to have fulfilled all the pre-license obligations before obtaining their first driver's license. The odds of a driver with a secondary education having formal driver training is 3.33 times higher than those with no education (OR 3.33, 95% CI 1.01-11.35). Drivers who were 60 years or older were 3.62 times more likely to be compliant than those who were between 20-29 years (OR 3.62, 95% CI 0.56-29.19). For the 98.3% of them who possessed valid licenses, 52.3% of them obtained them illegally. All the key officials saw RTIs as a serious public health problem but faced several challenges in the course of their work. Overall compliance with pre-license regulations was very poor. There is need for a review and strict enforcement of driver's license laws to improve compliance. Also vital are fostering inter-sectoral collaboration and improvement in the operations of all establishments involved in driver training and license procurement in Nigeria.

  5. Discharging a DC bus capacitor of an electrical converter system

    Science.gov (United States)

    Kajouke, Lateef A; Perisic, Milun; Ransom, Ray M

    2014-10-14

    A system and method of discharging a bus capacitor of a bidirectional matrix converter of a vehicle are presented here. The method begins by electrically shorting the AC interface of the converter after an AC energy source is disconnected from the AC interface. The method continues by arranging a plurality of switching elements of a second energy conversion module into a discharge configuration to establish an electrical current path from a first terminal of an isolation module, through an inductive element, and to a second terminal of the isolation module. The method also modulates a plurality of switching elements of a first energy conversion module, while maintaining the discharge configuration of the second energy conversion module, to at least partially discharge a DC bus capacitor.

  6. Distributed cooperative synchronization strategy for multi-bus microgrids

    DEFF Research Database (Denmark)

    Sun, Yao; Zhong, Chaolu; Hou, Xiaochao

    2017-01-01

    Microgrids can operate in both grid-connected mode and islanded mode. In order to smooth transfer from islanded mode to grid-connected mode, it is necessary to synchronize the point of common coupling (PCC) with main utility grid (UG) in voltage frequency, phase and amplitude. Conventional...... synchronization methods based on centralized communication are very costly and not suitable for multi-bus microgrids that have a large number of distributed generators (DGs). To address this concern, this study presents an active synchronization control strategy based on distributed cooperation technology...... for multi-bus microgrids. The proposed method can reconnect the microgrid in island to UG seamlessly with sparse communication channels. Synchronization correction signals are generated by a voltage controller, which are only transmitted to the leader DGs. Meanwhile, each DG exchanges information with its...

  7. Foundation field bus in the Spanish nuclear sector

    International Nuclear Information System (INIS)

    Saez de Montagut Revenga, G.

    2013-01-01

    This paper deals with the modification made in power plants nuclear ASCO 1 and 2 in which scans is the level Control system of Heaters to implementing an Ovation system, as well as the standard Foundation Field bus for field communications. This digitalisation has required a detailed study of the implications on security that could have the centralization of control loops in main feedwater system.

  8. BC Transit Fuel Cell Bus Project: Evaluation Results Report

    Energy Technology Data Exchange (ETDEWEB)

    Eudy, L. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Post, M. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2014-02-01

    This report evaluates a fuel cell electric bus demonstration led by British Columbia Transit (BC Transit) in Whistler, Canada. BC Transit is collaborating with the California Air Resources Board and the U.S. Department of Energy's National Renewable Energy Laboratory to evaluate the buses in revenue service. This evaluation report covers two years of revenue service data on the buses from April 2011 through March 2013.

  9. The Designing Bus for Nuclear Safety Class Controller

    International Nuclear Information System (INIS)

    Lee, Dongil; Lee, Myeongkyun; Yun, Donghwa; Ryoo, Kwangki

    2013-01-01

    EtherCAT (Ethernet for Control Automation Technology) is based on the IEEE 802.3 standard as one of the communication which is the I/O (Input/Output), sensors and communication function of PLC (Programmable Logic Controller) in industry and factory environment use is increasing. The Nuclear Safety Class Controller implemented by the EtherCAT applied bus can be shown the improving performance of data transmission in the controller

  10. Parallel data grabbing card based on PCI bus RS422

    International Nuclear Information System (INIS)

    Zhang Zhenghui; Shen Ji; Wei Dongshan; Chen Ziyu

    2005-01-01

    This article briefly introduces the developments of the parallel data grabbing card based on RS422 and PCI bus. It could be applied for grabbing the 14 bits parallel data in high speed, coming from the devices with RS422 interface. The methods of data acquisition which bases on the PCI protocol, the functions and their usages of the chips employed, the ideas and principles of the hardware and software designing are presented. (authors)

  11. The Designing Bus for Nuclear Safety Class Controller

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Dongil; Lee, Myeongkyun; Yun, Donghwa [PONUTech Co,. Ltd., Research Institute, Ulsan (Korea, Republic of); Ryoo, Kwangki [Hanbat National Univ., Daejeon (Korea, Republic of)

    2013-10-15

    EtherCAT (Ethernet for Control Automation Technology) is based on the IEEE 802.3 standard as one of the communication which is the I/O (Input/Output), sensors and communication function of PLC (Programmable Logic Controller) in industry and factory environment use is increasing. The Nuclear Safety Class Controller implemented by the EtherCAT applied bus can be shown the improving performance of data transmission in the controller.

  12. Low back trouble among urban bus drivers in Denmark

    DEFF Research Database (Denmark)

    Netterstrøm, Bo; Juel, K

    1989-01-01

    herniation was 137 compared to all Danish men. These differences were statistically significant. Of psychosocial factors only "the feeling of being mentally unbalanced" was found to be statistically significantly related to subsequent hospital discharge with a LBT-diagnosis. Long seniority as bus driver...... of those discharged from hospital with LBT makes it probable that LBT has etiologic factors in the work environment. The sedentary position and whole-body vibrations may be contributory causes....

  13. A counting-card circuit based on PCI bus

    International Nuclear Information System (INIS)

    Shi Jing; Li Yong; Chinese Academy of Sciences, Lanzhou; Su Hong; Dong Chengfu; Li Xiaogang; Ma Xiaoli

    2004-01-01

    A counting-card circuit based on PCI bus that we developed recently used for advanced personal computer will be introduced in this paper briefly. The maximum count capacity of this counting-card is 10 9 -1, ranging from 0 to 999 999 999, the maximum counting time range, 1 x 10 6 s, can be set in 1 cycle, the maximum counting rate is 20 MHz for positive input. (authors)

  14. Oxidative and nitrosative stress markers in bus drivers

    Czech Academy of Sciences Publication Activity Database

    Rössner ml., Pavel; Švecová, Vlasta; Milcová, Alena; Lněničková, Zdena; Solanský, I.; Santella, R. M.; Šrám, Radim

    2007-01-01

    Roč. 617, - (2007), s. 23-32 ISSN 0027-5107 R&D Projects: GA MŽP SL/5/160/05; GA AV ČR 1QS500390506 Institutional research plan: CEZ:AV0Z50390512 Keywords : oxidative stress * bus drivers * air pollution Subject RIV: DN - Health Impact of the Environment Quality Impact factor: 4.159, year: 2007

  15. Multi drop bus controller for IBM PC/AT

    International Nuclear Information System (INIS)

    Bardik, Yu.I.; Kalistratov, E.N.; Matyushin, A.A.; Obukhov, G.A.; Trofimov, N.N.

    1993-01-01

    The module PC-AT-PBC gives a possibility to create a working place based on the computer IBM PC/AT for testing of hardware which is compatible with the multi drop bus. The KP1830BE31 micro program change turns the module into timing generator for power supply controllers of the UNK correction system. The structure of the module, functional parts, library functions and two application programs have been described. 4 refs., 9 figs

  16. Definition and Evaluation of Bus and Truck Automation Operations Concepts

    OpenAIRE

    Tsao, H.-S. Jacob; Botha, Jan L.

    2002-01-01

    Traffic congestion will continue to worsen and likely worsen at a faster rate than ever. People throughput and freight throughput have become critical issues for California and the rest of the nation. PATH has been funding a one-year research project entitled "Definition and Evaluation of Bus and Truck Automation Operations Concepts," proposed by the authors. This report summarizes the results of the research project achieved during the first six months. During those six months, we reviewed l...

  17. Evaluation of Bus Vibration Comfort Based on Passenger Crowdsourcing Mode

    Directory of Open Access Journals (Sweden)

    Hong Zhao

    2016-01-01

    Full Text Available Vibration comfort is an important factor affecting the quality of service (QoS of bus. In order to make people involved in supervising bus’s vibration comfort and improve passengers’ riding experience, a novel mode of passenger crowdsourcing is introduced. In this paper, comfort degree of bus vibration is calculated from bus’s vibration signals collected by passengers’ smartphones and sent through WiFi to the Boa web server which shows the vibration comfort on the LCD deployed in bus and maybe trigger alarm lamp when the vibration is beyond the threshold. Three challenges here have been overcome: firstly, space coordinate transformation algorithm is used to solve the constant drift of signals collected; secondly, a low-pass filter is designed to isolate gravity from signals real-timely via limited computing resources; thirdly, an embedded evaluation system is developed according to the calculation procedure specified by criterion ISO 2631-1997. Meanwhile, the model proposed is tested in a practical running environment, the vibration data in whole travel are recorded and analyzed offline. The results show that comfort degree of vibration obtained from the experimental system is identical with the truth, and this mode is proved to be effective.

  18. HEV Test Bench Based on CAN Bus Sensor Communication

    Directory of Open Access Journals (Sweden)

    Shupeng ZHAO

    2014-02-01

    Full Text Available The HEV test bench based on Controller Area Network bus was studied and developed. Control system of HEV power test bench used the CAN bus technology. The application of CAN bus technology on control system development has opened up a new research direction for domestic automobile experimental platform. The HEV power control system development work was completed, including power master controller, electric throttle controller, driving simulation platform, CAN2.0 B communication protocol procedures for formulation, CAN communication monitoring system, the simulation model based on MATLAB code automatic generation technology research, etc. Maximum absorption power of the test bench is 90 kW, the test bench top speed is 6000 r/min, the CAN communication data baud rate is 10~500 k, the conventional electric measurement parameter part precision satisfies the requirement of development of HEV. On the HEV test bench the result of regenerative braking experiment shows that the result got by the test bench was closer to the results got by outdoor road test. And the fuel consumption experiment test results show that the HEV fuel consumption and the charge-discharge character are in linear relationship. The establishment of the test platform for the evaluation of the development of hybrid electric vehicle and power provides physical simulation and test platform.

  19. Electric bus migration in Bengaluru with dynamic charging technologies

    Directory of Open Access Journals (Sweden)

    Ankit Kumar Begwani

    2017-12-01

    Full Text Available Rapid but unplanned urban development coupled with economic growth has resulted in congestion and pollution concerns in Indian cities. This forced India consider taking concrete steps towards design policies that would help stir the nation towards a more sustainable future. India, along with other bigger Asian economies like China, needs to address the growing global concerns over climate change and design their framework and policies to help cut down the greenhouse gas emissions. Transportation is a major source of pollution. A shift towards a pro-public transport policy would solve the traffic congestion problems and address the emission concerns. India has a significantly higher modal share of public transportation in its major cities. Public bus transport system acts as a lifeline to the India’s poor and middle class citizens. The following study focuses on the need for a replacement of conventional fossil fuel dependent buses with Electric buses in the existing public transport bus fleet in the city of Bengaluru. A design has been developed to utilize wireless charging technologies to realize electric bus migration in Bengaluru.

  20. Pilot survey of subway and bus stop noise levels.

    Science.gov (United States)

    Gershon, Robyn R M; Neitzel, Richard; Barrera, Marissa A; Akram, Muhammad

    2006-09-01

    Excessive noise exposure is a serious global urban health problem, adversely affecting millions of people. One often cited source of urban noise is mass transit, particularly subway systems. As a first step in determining risk within this context, we recently conducted an environmental survey of noise levels of the New York City transit system. Over 90 noise measurements were made using a sound level meter. Average and maximum noise levels were measured on subway platforms, and maximum levels were measured inside subway cars and at several bus stops for comparison purposes. The average noise level measured on the subway platforms was 86 +/- 4 dBA (decibel-A weighting). Maximum levels of 106, 112, and 89 dBA were measured on subway platforms, inside subway cars, and at bus stops, respectively. These results indicate that noise levels in subway and bus stop environments have the potential to exceed recommended exposure guidelines from the World Health Organization (WHO) and U.S. Environmental Protection Agency (EPA), given sufficient exposure duration. Risk reduction strategies following the standard hierarchy of control measures should be applied, where feasible, to reduce subway noise exposure.

  1. Replacement model of city bus: A dynamic programming approach

    Science.gov (United States)

    Arifin, Dadang; Yusuf, Edhi

    2017-06-01

    This paper aims to develop a replacement model of city bus vehicles operated in Bandung City. This study is driven from real cases encountered by the Damri Company in the efforts to improve services to the public. The replacement model propounds two policy alternatives: First, to maintain or keep the vehicles, and second is to replace them with new ones taking into account operating costs, revenue, salvage value, and acquisition cost of a new vehicle. A deterministic dynamic programming approach is used to solve the model. The optimization process was heuristically executed using empirical data of Perum Damri. The output of the model is to determine the replacement schedule and the best policy if the vehicle has passed the economic life. Based on the results, the technical life of the bus is approximately 20 years old, while the economic life is an average of 9 (nine) years. It means that after the bus is operated for 9 (nine) years, managers should consider the policy of rejuvenation.

  2. Safety evaluation of a hydrogen fueled transit bus

    Energy Technology Data Exchange (ETDEWEB)

    Coutts, D.A.; Thomas, J.K.; Hovis, G.L.; Wu, T.T. [Westinghouse Savannah River Co., Aiken, SC (United States)

    1997-12-31

    Hydrogen fueled vehicle demonstration projects must satisfy management and regulator safety expectations. This is often accomplished using hazard and safety analyses. Such an analysis has been completed to evaluate the safety of the H2Fuel bus to be operated in Augusta, Georgia. The evaluation methods and criteria used reflect the Department of Energy`s graded approach for qualifying and documenting nuclear and chemical facility safety. The work focused on the storage and distribution of hydrogen as the bus motor fuel with emphases on the technical and operational aspects of using metal hydride beds to store hydrogen. The safety evaluation demonstrated that the operation of the H2Fuel bus represents a moderate risk. This is the same risk level determined for operation of conventionally powered transit buses in the United States. By the same criteria, private passenger automobile travel in the United States is considered a high risk. The evaluation also identified several design and operational modifications that resulted in improved safety, operability, and reliability. The hazard assessment methodology used in this project has widespread applicability to other innovative operations and systems, and the techniques can serve as a template for other similar projects.

  3. Violence against metropolitan bus drivers and fare collectors in Brazil

    Directory of Open Access Journals (Sweden)

    Ada Ávila Assunção

    2015-01-01

    Full Text Available OBJECTIVE To analyze the correlation between sociodemographic factors and working conditions of bus workers in a metropolitan area and violence against them. METHODS This cross-sectional study used a nonprobabilistic sample estimated according to the number of workers employed in bus companies located in three cities in the Belo Horizonte metropolitan region in 2012 (N = 17,470. Face-to-face interviews were conducted using a digital questionnaire. The factors associated with violence were analyzed in two stages using Poisson regression, according to each level. The magnitude of the association was evaluated using prevalence ratios with robust variance and a statistical significance of 5%, and 95% confidence intervals were obtained. RESULTS The study sample comprised 782 drivers and 691 fare collectors; 45.0% participants reported at least one act of violence in the workplace in the last 12 months, with passengers being predominantly responsible. The age of the bus workers was inversely associated with violence. Chronic diseases, sickness absenteeism, and working conditions were also associated with violence. CONCLUSIONS The findings on the correlation between violence and working conditions are essential for implementing prevention strategies by transportation service managers.

  4. Intercâmbio acadêmico cultural internacional: uma experiência de crescimento pessoal e científico

    Directory of Open Access Journals (Sweden)

    Indiara Sartori Dalmolin

    2013-06-01

    Full Text Available Este estudo objetivou descrever a experiência discente ao integrar um programa de mobilidade acadêmica internacional, durante a graduação em enfermagem. Trata-se de relato da vivência acadêmica em Portugal, na Universidade do Algarve, viabilizada pela Universidade Federal de Santa Maria, Rio Grande do Sul, Brasil. A experiência de intercâmbio realizada no período de seis meses, possibilitou a aquisição de novos conhecimentos científicos e culturais, inclusive inovações de tecnologias em saúde, desenvolvimento de pesquisa e vínculos acadêmicos. Como contribuições, espera-se estimular e intensificar a mobilidade internacional especialmente no âmbito da graduação, considerando a sua importância para o aperfeiçoamento da formação acadêmica e a excelência do ensino superior brasileiro por meio do intercâmbio científico e cultural no exterior.

  5. Cellular Automata Based Modeling for Evaluating Different Bus Stop Designs in China

    Directory of Open Access Journals (Sweden)

    Haoyang Ding

    2015-01-01

    Full Text Available A cellular automaton model is proposed to simulate mixed traffic flow composed of motor vehicles and bicycles near bus stops. Three typical types of bus stops which are common in China are considered in the model, including two types of curbside bus stops and one type of bus bay stops. Passenger transport capacity of three types of bus stops, which is applied to evaluate the bus stop design, is calculated based on the corresponding traffic flow rate. According to the simulation results, the flow rates of both motor vehicles and bicycles exhibit phase transition from free flow to the saturation one at the critical point. The results also show that the larger the interaction between motor vehicle and bicycle flow is near curbside bus stops, the more the value of saturated flows drops. Curbside bus stops are more suitable when the conflicts between two flows are small and the inflow rate of motor vehicles is low. On the contrary, bus bay stops should be applied due to their ability to reduce traffic conflicts. Findings of this study can provide useful suggestions on bus stop selection considering different inflow rate of motor vehicles and bicycles simultaneously.

  6. Working conditions of bus drivers in the private sector and bus crashes in Kandy district, Sri Lanka: a case-control study.

    Science.gov (United States)

    Jayatilleke, A U; Nakahara, S; Dharmaratne, S D; Jayatilleke, A C; Poudel, K C; Jimba, M

    2009-04-01

    To explore the effects of working conditions of private-bus drivers on bus crashes in Kandy district, Sri Lanka. A case-control study was carried out from August to September 2006. All private-bus drivers registered in Kandy district and involved in crashes reported to the police between November 2005 and April 2006 (n = 63) were selected as cases. Two control groups were included: private-bus drivers working on the same routes as the case drivers (n = 90) and private-bus drivers selected randomly from other routes of the district (n = 111). Data were collected using an anonymous self-administered questionnaire. Associations between working conditions and crashes were analysed using logistic regression. A strong association was observed between drivers' disagreements about working hours and bus crashes (matched controls, adjusted odds ratio (AOR) 5.98, 95% CI 1.02 to 34.90; unmatched controls, AOR 18.74, 95% CI 2.00 to 175.84). A significant association was also observed between low salaries (US$100) and private-bus crashes (matched controls, AOR 1.01, 95% CI 0.40 to 2.54; unmatched controls, AOR 3.09, 95% CI 1.26 to 7.57). Drivers' disagreements about working hours and low salaries were significant risk factors for private-bus crashes in Kandy district, Sri Lanka. Therefore, new legislation for private-bus owners on the working hours and salaries of their drivers to prevent private-bus crashes is recommended.

  7. MIL-STD-1553 dynamic bus controller/remote terminal hybrid set

    Science.gov (United States)

    Friedman, S. N.

    This paper describes the performance, physical and electrical requirements of a Dual Redundant BUS Interface Unit (BIU) acting as a BUS Controller Interface Unit (BCIU) or Remote Terminal Unit (RTU) between a Motorola 68000 VME BUS and MIL-STD-1553B Multiplex Data Bus. A discussion of how the BIU Hybrid set is programmed, and operates as a BCIU or RTU, will be included. This paper will review Dynamic Bus Control and other Mode Code capabilities. The BIU Hybrid Set interfaces to a 68000 Microprocessor with a VME Bus using programmed I/O transfers. This special interface will be discussed along with the internal Dual Access Memory (4K x 16) used to support the data exchanges between the CPU and the BIU Hybrid Set. The hybrid set's physical size and power requirements will be covered. This includes the present Double Eurocard the BIU function is presently being offered on.

  8. Identification of voltage stability condition of a power system using measurements of bus variables

    Directory of Open Access Journals (Sweden)

    Durlav Hazarika

    2014-12-01

    Full Text Available Several online methods were proposed for investigating the voltage stability condition of an interconnected power system using the measurements of voltage and current phasors at a bus. For this purpose, phasor measurement units (PMUs are used. A PMU is a device which measures the electrical waves on an electrical network, using a common time source (reference bus for synchronisation. This study proposes a method for online monitoring of voltage stability condition of a power system using measurements of bus variables namely – (i real power, (ii reactive power and (iii bus voltage magnitude at a bus. The measurements of real power, reactive power and bus voltage magnitude could be extracted/captured from a smart energy meter. The financial involvement for implementation of the proposed method would significantly lower compared with the PMU-based method.

  9. Bitmap-Wise Wireless M-Bus Coordination for Sustainable Real Time Energy Management

    Directory of Open Access Journals (Sweden)

    Kwang-il Hwang

    2014-07-01

    Full Text Available Even though WM-Bus is being considered to be the most promising network protocol for smart metering, it is not suitable for a sustainable real-time home energy management system (HEMS, which requires higher reliability and longer lifetime despite real time bi-directional communications. Therefore, in this paper we propose a Bitmap-wise WM-Bus (BWM-Bus, coping well with sustainable real-time HEMS. In particular, the proposed scheme addresses the several problems in WM-Bus for HEMS by introducing novel functions: asynchronous meter trigger, adaptive slot scheduling, and bitmap-wise retransmission request. Through experiments, we demonstrate that BWM-Bus guarantees higher data success ratio with lower data aggregation time, as well as longer lifetime than WM-Bus standard.

  10. A Model of Bus Bunching under Reliability-based Passenger Arrival Patterns

    OpenAIRE

    Fonzone, Achille; Schmöcker, Jan-Dirk; Liu, Ronghui

    2015-01-01

    If bus service departure times are not completely unknown to the passengers, non-uniform passenger arrival patterns can be expected. We propose that passengers decide their arrival time at stops based on a continuous logit model that considers the risk of missing services. Expected passenger waiting times are derived in a bus system that allows also for overtaking between bus services. We then propose an algorithm to derive the dwell time of subsequent buses serving a stop in order to illustr...

  11. The Bus Extension Module Design and Verification of POSAFE-Q Using LVDS

    International Nuclear Information System (INIS)

    Lee, Youn Sang; Song, Seung Whan; No, Young Hun; Yoo, Kwan Woo

    2012-01-01

    This paper described the Bus Extension Module using Low Voltage Differential Signal (LVDS). A Bus Extension Module use Safety-Related PLC (Programmable Logic Controller), called POSAFE-Q (made by POSCO ICT), for handling many data (I/O) extension rack. A processor module of POSAFE-Q can control I/O Module installed another rack. This paper explains Bus Extension Module and Data transfer technology using LVDS. (author)

  12. Small Explorer Data System MIL-STD-1773 fiber optic bus

    Science.gov (United States)

    Flanegan, Mark; Label, Ken

    1992-01-01

    The MIL-STD-1773 Fiber Optic Data Bus as implemented in the GSFC Small Explorer Data System (SEDS) for the Small Explorer Program is described. It provides an overview of the SEDS MIL-STD-1773 bus components system design considerations, reliability figures, acceptance and qualification testing requirements, radiation requirements and tests, error handling considerations, and component heritage. The first mission using the bus will be launched in June of 1992.

  13. Evaluation of Urban Bus Transport Failure in Gujranwala City of Pakistan

    Directory of Open Access Journals (Sweden)

    MUHAMMAD WAQAR ASLAM

    2017-07-01

    Full Text Available This research work has evaluated the performance of urban public bus transport service operating in Gujranwala city of Pakistan. The assessment has been made in terms of financial viability, bus condition, operational performance and user perception. Based on the data requirements, various traffic/transport surveys were conducted including Passenger Boarding and Alighting Survey, Bus Count Survey, Bus Inspection Survey, Illegal Operations Survey and Public Transport User Interview Survey in consultation with concerned department/agencies. Field surveys were also conducted to get input from passengers and local people. Initial investigation informed that out of four operational bus routes, only two routes are profitable. The overall bus operation is running in loss (only 0.3% net profit. It has barely any profit for the bus operator against its investment thereby making the urban bus operation financially non-viable. The whole revenue flow is dependent on passenger ticketing revenue only. Around 35% of the buses are in poor condition with major issues of quality of tyres, no speedometer, worse condition of seats, floor and ceiling, and display of route. Illegal operation of Qingqis/Rickshaws (as para-transit mode along the bus routes is also decreasing the revenue by capturing the passenger volume. According to passenger opinion analysis, around 55% of the passenger are not satisfied with the service quality and prefer other modes of transport. Their major concerns are absence of facilities for disables and bus stops, bus seating and standing capacity, poor bus condition and pick pocketing. Collectively, these factors are contributing

  14. The impact of bus drivers ’ lifestyle on the occurrence of health problems and absenteeism

    OpenAIRE

    Andrej Jerman; Maja Meško

    2016-01-01

    Research Question: Do bus drivers’ lifestyles affect the occurrence of health problems and absenteeism? Purpose: The purpose of the study was to determine whether the lifestyle of professional bus drivers affects the occurrence of health problems and the phenomenon of absenteeism. Method: A quantitative research method was used in the research. Data were collected using a structured questionnaire, on a sample of 230 professional bus drivers from differ...

  15. Best Operational and Maintenance Practices for City Bus Fleets to Maximize Fuel Economy

    OpenAIRE

    Energy Sector Management Assistance Program

    2011-01-01

    In most large cities in developing countries, buses continue to be the public transport option of choice, carrying a large share of urban travelers. However, transit bus companies in these countries are often cash-strapped. In many cases, the operating cost per bus kilometer exceeds revenues and bus fares are often kept low irrespective of the cost of providing service. Many cities are dom...

  16. Changes in Service and Associated Ridership Impacts near a New Light Rail Transit Line

    Directory of Open Access Journals (Sweden)

    Jeongwoo Lee

    2017-10-01

    Full Text Available Los Angeles (LA, for many years a city with limited rail transit, is substantially expanding its public transit system. This paradigm change in transportation policy and investment creates new requirements for monitoring. One area needing evaluation is whether new, high quality transit options, such as light rail, near existing transit services increase sustainable transportation mode shares and reduce car travel. Few studies have explored light rail’s role as a catalyst to increase overall transit use and achieve sustainability goals within an auto-oriented city like LA. Metro’s data show that trips taken on its bus and rail system dropped overall by 10.5% between 2009 and 2016, but its rail ridership grew 21% during the same period due to the debut of the Gold Line and Expo Line extensions. We analyze changes to bus service and associated ridership impacts that resulted from the opening of these two LRT lines in LA. The immediate effect of the city’s bus service changes along the Gold Line light rail extension appear to be associated with a net “bus plus rail” ridership decline in that corridor. In contrast, the Expo Line corridor experienced an initial increase in ridership during the two years immediately after its opening, possibly because the bus service was not reduced by the same magnitude as along the Gold Line extension. Our findings indicate that changes in bus service made to coincide with the introduction of new light rail transit (LRT can negatively affect the overall transit ridership in the corridor. Planners and policy makers should closely monitor changes in bus service and ridership associated with new rail transit to ensure investments results in an overall net increase in more sustainable travel.

  17. Analysis of bus passenger comfort perception based on passenger load factor and in-vehicle time.

    Science.gov (United States)

    Shen, Xianghao; Feng, Shumin; Li, Zhenning; Hu, Baoyu

    2016-01-01

    Although bus comfort is a crucial indicator of service quality, existing studies tend to focus on passenger load and ignore in-vehicle time, which can also affect passengers' comfort perception. Therefore, by conducting surveys, this study examines passengers' comfort perception while accounting for both factors. Then, using the survey data, it performs a two-way analysis of variance and shows that both in-vehicle time and passenger load significantly affect passenger comfort. Then, a bus comfort model is proposed to evaluate comfort level, followed by a sensitivity analysis. The method introduced in this study has theoretical implications for bus operators attempting to improve bus service quality.

  18. ARCNET as a field bus in the Fermilab linac control system

    International Nuclear Information System (INIS)

    Shea, M.F.; Goodwin, R.W.; Kucera, M.J.; Shtirbu, S.

    1992-01-01

    Data acquisition hardware in accelerator control systems is connected by a field bus to networked computers that supply data to consoles. Industry attempts to standardize on a low level field bus have not succeeded in providing a single well-supported bus. This paper describes a data acquisition chassis that connects to VMEbus computers using ARCNET, a full featured token-passing local area network, as the field bus. The performance of this technique as implemented in the control system for the Fermilab Linac is given. (author)

  19. Hierarchical Delay-Dependent Distributed Coordinated Control for DC Ring-Bus Microgrids

    DEFF Research Database (Denmark)

    Dou, Chunxia; Yue, Dong; Zhang, Zhanqiang

    2017-01-01

    In this paper, a hierarchical distributed coordinated control method is proposed based on the multi-agent system for dc ring-bus microgrids to improve the bus voltage performance. First, a two-level multi-agent system is built, where each first-level unit control agent is associated with a distri......In this paper, a hierarchical distributed coordinated control method is proposed based on the multi-agent system for dc ring-bus microgrids to improve the bus voltage performance. First, a two-level multi-agent system is built, where each first-level unit control agent is associated...

  20. Analyzing the Relationship Between Bus Pollution Policies and Morbidity Using a Quasi-Experiment.

    Science.gov (United States)

    Ngo, Nicole S

    2015-09-01

    Transit buses are used by millions of commuters every day, but they emit toxic diesel fumes. In 1988, the U.S. Environmental Protection Agency implemented emission standards for transit buses, which have been continually updated. Yet there is no quantitative evidence of the health benefits from these bus pollution policies due to data constraints and confounding variables. In this study, a quasi-experiment is used to exploit the geographic and temporal variation in emission standards by using bus vintage as a proxy for bus emissions. This is accomplished using a unique, rich panel data set, which includes daily information on bus vintage and route for the New York City Transit bus fleet between 2006 and 2009. This information is merged with daily data on emergency department (ED) visits for respiratory illnesses, which include patients' residences at the census block level and exact admission date. Economic benefits resulting from these bus pollution policies are then estimated. Results show that stricter transit bus emission standards by the U.S. Environmental Protection Agency for particulate matter are associated with reduced ED visits for respiratory diseases for patients living within a few hundred feet of a bus route. These findings demonstrate that bus pollution policies have made critical improvements to public health.

  1. Concentrations and risk assessment of selected monoaromatic hydrocarbons in buses and bus stations of Hangzhou, China.

    Science.gov (United States)

    Li, Shuang; Chen, Shuguang; Zhu, Lizhong; Chen, Xiasheng; Yao, Chaoying; Shen, Xueyou

    2009-03-01

    Air pollution surveys of ten selected monoaromatic hydrocarbons (MAHCs) were conducted in buses and bus stations in Hangzhou, China. The mean concentrations of MAHCs in the air of buses and bus stations were 95.9 and 36.5 microg/m(3), respectively, of which toluene was the highest in all the sampling sites. Mean concentrations of all MAHCs in buses were statistically higher than those nearby bus stations (pbus drivers were 1.11x10(-5) and 4.00x10(-5), respectively, which were way above the limit set by USEPA. The health risk caused by MAHCs in bus microenvironment should be cautioned.

  2. Study Of The Risks Arising From Natural Disasters And Hazards On Urban And Intercity Motorways By Using Failure Mode Effect Analysis (FMEA) Methods

    Science.gov (United States)

    DELİCE, Yavuz

    2015-04-01

    Highways, Located in the city and intercity locations are generally prone to many kind of natural disaster risks. Natural hazards and disasters that may occur firstly from highway project making to construction and operation stages and later during the implementation of highway maintenance and repair stages have to be taken into consideration. And assessment of risks that may occur against adverse situations is very important in terms of project design, construction, operation maintenance and repair costs. Making hazard and natural disaster risk analysis is largely depending on the definition of the likelihood of the probable hazards on the highways. However, assets at risk , and the impacts of the events must be examined and to be rated in their own. With the realization of these activities, intended improvements against natural hazards and disasters will be made with the utilization of Failure Mode Effects Analysis (FMEA) method and their effects will be analyzed with further works. FMEA, is a useful method to identify the failure mode and effects depending on the type of failure rate effects priorities and finding the most optimum economic and effective solution. Although relevant measures being taken for the identified risks by this analysis method , it may also provide some information for some public institutions about the nature of these risks when required. Thus, the necessary measures will have been taken in advance in the city and intercity highways. Many hazards and natural disasters are taken into account in risk assessments. The most important of these dangers can be listed as follows; • Natural disasters 1. Meteorological based natural disasters (floods, severe storms, tropical storms, winter storms, avalanches, etc.). 2. Geological based natural disasters (earthquakes, tsunamis, landslides, subsidence, sinkholes, etc) • Human originated disasters 1. Transport accidents (traffic accidents), originating from the road surface defects (icing

  3. Insights into iodine behaviour and speciation in the Phébus primary circuit

    International Nuclear Information System (INIS)

    Girault, N.; Payot, F.

    2013-01-01

    during the four Phébus-bundle tests. In these tests, the impact of different oxido-reducing and thermal– hydraulics conditions prevailing in the primary circuit as well as the impact of boron and control rod materials on iodine behaviour has been investigated. In this test series, iodine behaviour in the FPT3 primary circuit clearly departed from the others because a much higher iodine retention was observed upstream the steam generator (due to partial boron-rich blockage after 14,500 s) but above all a much higher gaseous iodine fraction in hot and cold legs was formed as compared to other tests. In the three other Phébus FP tests, iodine was generally poorly retained in the primary circuit (70% of released iodine reaching the containment vessel). Two main zones of significant deposition were identified coinciding with sections in which temperatures dropped rapidly. These were the fuel bundle exit (upper plenum and vertical line) where the gas cooled from very high fuel temperatures down to 700 °C and the steam generator riser (upstream part and hot leg entrance) where temperatures cooled from 700 °C to 150 °C. As expected, iodine was mainly transported under vapour forms in the circuit hot leg. However, Phébus FP tests provided new insights into iodine transport, as several volatile iodine vapour species not associated to caesium were evidenced. In all tests, a significant amount of iodine under a gaseous form was found in the containment early during the bundle transient phase, implying that this gas was originated from the circuit. Except for FPT3, measurements of gaseous iodine in the circuit, from discrete samplings, were however more contradictory as only negligible amounts of gaseous iodine were generally measured in the cold leg. Due to the limitations of such measurements (trapping efficiencies, limited period of samplings) the gaseous iodine occurrence in the primary circuit during FPT0/1/2 could neither be stated nor refuted. Finally, Phébus FP test

  4. Massachusetts Fuel Cell Bus Project: Demonstrating a Total Transit Solution for Fuel Cell Electric Buses in Boston

    Energy Technology Data Exchange (ETDEWEB)

    2017-05-22

    The Federal Transit Administration's National Fuel Cell Bus Program focuses on developing commercially viable fuel cell bus technologies. Nuvera is leading the Massachusetts Fuel Cell Bus project to demonstrate a complete transit solution for fuel cell electric buses that includes one bus and an on-site hydrogen generation station for the Massachusetts Bay Transportation Authority (MBTA). A team consisting of ElDorado National, BAE Systems, and Ballard Power Systems built the fuel cell electric bus, and Nuvera is providing its PowerTap on-site hydrogen generator to provide fuel for the bus.

  5. Physics Bus: An Innovative Model for Public Engagement

    Science.gov (United States)

    Fox, Claire

    The Physics Bus is about doing science for fun. It is an innovative model for science outreach whose mission is to awaken joy and excitement in physics for all ages and walks of life - especially those underserved by science enrichment. It is a mobile exhibition of upcycled appliances-reimagined by kids-that showcase captivating physics phenomena. Inside our spaceship-themed school bus, visitors will find: a microwave ionized-gas disco-party, fog rings that shoot from a wheelbarrow tire, a tv whose electron beam is controlled by a toy keyboard, and over 20 other themed exhibits. The Physics Bus serves a wide range of public in diverse locations from local neighborhoods, urban parks and rural schools, to cross-country destinations. Its approachable, friendly and relaxed environment allows for self-paced and self-directed interactions, providing a positive and engaging experience with science. We believe that this environment enriches lives and inspires people. In this presentation we will talk about the nuts and bolts that make this model work, how the project got started, and the resources that keep it going. We will talk about the advantages of being a grassroots and community-based organization, and how programs like this can best interface with universities. We will explain the benefits of focusing on direct interactions and why our model avoids ``teaching'' physics content with words. Situating our approach within a body of research on the value of informal science we will discuss our success in capturing and engaging our audience. By the end of this presentation we hope to broaden your perception of what makes a successful outreach program and encourage you to value and support alternative outreach models such as this one. In Collaboration with: Eva Luna, Cornell University; Erik Herman, Cornell University; Christopher Bell, Ithaca City School District.

  6. DIMETHYL ETHER (DME)-FUELED SHUTTLE BUS DEMONSTRATION PROJECT

    Energy Technology Data Exchange (ETDEWEB)

    Elana M. Chapman; Shirish Bhide; Jennifer Stefanik; Andre L. Boehman; David Klinikowski

    2003-04-01

    The objectives of this research and demonstration program are to convert a campus shuttle bus to operation on dimethyl ether, a potential ultra-clean alternative diesel fuel. To accomplish this objective, this project includes laboratory evaluation of a fuel conversion strategy, as well as, field demonstration of the DME-fueled shuttle bus. Since DME is a fuel with no lubricity (i.e., it does not possess the lubricating quality of diesel fuel), conventional fuel delivery and fuel injection systems are not compatible with dimethyl ether. Therefore, to operate a diesel engine on DME one must develop a fuel-tolerant injection system, or find a way to provide the necessary lubricity to the DME. In this project, they have chosen the latter strategy in order to achieve the objective with minimal need to modify the engine. The strategy is to blend DME with diesel fuel, to obtain the necessary lubricity to protect the fuel injection system and to achieve low emissions. The laboratory studies have included work with a Navistar V-8 turbodiesel engine, demonstration of engine operation on DME-diesel blends and instrumentation for evaluating fuel properties. The field studies have involved performance, efficiency and emissions measurements with the Champion Motorcoach ''Defender'' shuttle bus which will be converted to DME-fueling. The results include baseline emissions, performance and combustion measurements on the Navistar engine for operation on a federal low sulfur diesel fuel (300 ppm S). Most recently, they have completed engine combustion studies on DME-diesel blends up to 30 wt% DME addition.

  7. Scheduling with Bus Access Optimization for Distributed Embedded Systems

    DEFF Research Database (Denmark)

    Eles, Petru; Doboli, Alex; Pop, Paul

    2000-01-01

    of control. Our goal is to derive a worst case delay by which the system completes execution, such that this delay is as small as possible; to generate a logically and temporally deterministic schedule; and to optimize parameters of the communication protocol such that this delay is guaranteed. We have......In this paper, we concentrate on aspects related to the synthesis of distributed embedded systems consisting of programmable processors and application-specific hardware components. The approach is based on an abstract graph representation that captures, at process level, both dataflow and the flow......, generates an efficient bus access scheme as well as the schedule tables for activation of processes and communications....

  8. Development of bus duct inspection robot at nuclear power plant

    International Nuclear Information System (INIS)

    Hamada, Mamoru; Hoshi, Teruaki; Komura, Yoshinari

    2017-01-01

    Under the present situation, nuclear power plant has some places which are inspected with difficulty or not inspected due to narrowness or physical restriction, when carrying out periodical inspection. The subject of our research and development is to improve the accuracy of inspection and also to save labor (liberation from distress work of the worker) by applying a robot technology to the periodical inspection of the nuclear power plant. As a specific example, we report that developed robot can inspect inside the narrow space of Isolated Phase Bus ducts, which connect between a turbine generator and the main transformer. (author)

  9. Multifactor-Driven Hierarchical Routing on Enterprise Service Bus

    Science.gov (United States)

    Mi, Xueqiang; Tang, Xinhuai; Yuan, Xiaozhou; Chen, Delai; Luo, Xiangfeng

    Message Routing is the foremost functionality on Enterprise Service Bus (ESB), but current ESB products don't provide an expected solution for it, especially in the aspects of runtime route change mechanism and service orchestration model. In order to solve the above drawbacks, this paper proposes a multifactor-driven hierarchical routing (MDHR) model. MDHR defines three layers for message routing on ESB. Message layer gives the original support for message delivery. Application layer can integration or encapsulate some legacy applications or un-standard services. Business layer introduces business model to supplies developers with a business rule configuration, which supports enterprise integration patterns and simplifies the service orchestration on ESB.

  10. BC Transit Fuel Cell Bus Project Evaluation Results: Second Report

    Energy Technology Data Exchange (ETDEWEB)

    Eudy, L.; Post, M.

    2014-09-01

    Second report evaluating a fuel cell electric bus (FCEB) demonstration led by British Columbia Transit (BC Transit) in Whistler, Canada. BC Transit is collaborating with the California Air Resources Board and the U.S. Department of Energy's National Renewable Energy Laboratory to evaluate the buses in revenue service. NREL published its first report on the demonstration in February 2014. This report is an update to the previous report; it covers 3 full years of revenue service data on the buses from April 2011 through March 2014 and focuses on the final experiences and lessons learned.

  11. Economic Optimization Analysis of Chengdu Electric Community Bus Operation

    Science.gov (United States)

    Yidong, Wang; Yun, Cai; Zhengping, Tan; Xiong, Wan

    2018-03-01

    In recent years, the government has strongly supported and promoted electric vehicles and has given priority to demonstration and popularization in the field of public transport. The economy of public transport operations has drawn increasing attention. In this paper, Chengdu wireless charging pure electric community bus is used as the research object, the battery, air conditioning, driver’s driving behavior and other economic influence factors were analyzed, and optimizing the operation plan through case data analysis, through the reasonable battery matching and mode of operation to help businesses effectively save operating costs and enhance economic efficiency.

  12. Fuel options for public bus fleets in Sweden

    OpenAIRE

    Xylia, Maria; Silveira, Semida

    2015-01-01

    The Swedish public transport sector has defined two major targets, i.e., to run 90% of the total vehicle kilometers of the fleet on non-fossil fuels and double the volume of travel via public transport by 2020, increasing the share of public transport in relation to the total personal transport in the country . The f3 report Fuel options for public bus fleets in Sweden highlights the challenges and solutions encountered, particularly when it comes to the adoption of renewable fuels in the reg...

  13. Modeling and simulation of bus assem-bling process using DES/ABS approach

    Directory of Open Access Journals (Sweden)

    Pawel PAWLEWSKI

    2017-03-01

    Full Text Available This paper presents the results of the project, which goal is to analyze the production process capability after reengineering the assembly process due to expansion of a bus production plant. The verification of the designed work organization for the new configuration of workstations on new production hall is necessary. To solve these  problems authors propose a method based on mixing DES (Discrete Event Simulation and ABS (Agent Based Simulation approach. DES is using to model the main process – material flow (buses, ABS is using to model assembling operations of teams of  workers.One of obtained goal is to build a simulation model, which presents the new assembly line in the factory, taking into ac-count the arrangement of workstations and work teams in the new production hall as well as the transport between workstations. Second goal is to present work organization of work teams and division of individual workers’ labor (who belongs to a particular work team and performs operations on buses in a particular workstation in order to determine the best allocation of tasks and the optimum size of individual work teams. Proposed solution enables to determine the effect of assembly interferences on the work of particular work teams and the efficiency of the whole production system, to define the efficiency of the designed assembly lines and proposing changes aimed at the quality improvement of the created conception. 

  14. InterCity tilting e.m.u. for Deutsche Bahn; InterCity-Triebzuege mit Neigetechnik fuer die Deutsche Bahn

    Energy Technology Data Exchange (ETDEWEB)

    Behmann, U.

    1999-07-01

    When changing time schedule in the end of may 1999 the German Railway (DB) starts with a new generation of electric intercity trains for 1 AC 15 kV 16 2/3 Hz. Five trains with tilt mechanism will travel between Stuttgart - Singen - Schaffhausen - Zurich. For this purpose these trains are equipped in addition with swiss current collectors and safety engineering. [German] Zum Fahrplanwechsel Ende Mai 1999 wird die Deutsche Bahn (DB) mit einer neuen Generation elektrischer InterCity-Triebzuege fuer 1 AC 15 kV 16 2/3 Hz in den kommerziellen Dienst gehen. Mit fuenf Zuegen Baureihe (BR) 415 mit Neigetechnik (ICT) wird sie die Relation Stuttgart - Singen - Schaffhausen - Zuerich bedienen. Dafuer wurden diese fuenf Zuege zusaetzlich mit schweizerischer Stromabnehmerwippe und Zugsicherungseinrichtung ausgeruestet. (orig/GL)

  15. CFD analysis of flow in engine compartment of large urban bus; Ogata bus no engine room nai nagare kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Hoshino, H; Otake, M; Iioka, K [Nissan Diesel Motor Co. Ltd., Saitama (Japan); Sato, K [Subaru Research Center Co. Ltd., Tokyo (Japan)

    1997-10-01

    A CFD simulation was performed to analyze the air flow in the engine compartment of a large urban bus. The conventional simulation technique takes a long time to perform the parameter study of a complex engine compartment shape. In this study, the use of orthogonal grids made modeling the engine compartment easy, so parameter study on modification of the engine compartment structure could be conducted in a short time. Thus this simulation enables engineers to more clearly understand the air flow patterns in the engine compartment, and to get guidlines for modifying the compartment structure to improve the cooling performance. 1 ref., 12 figs.

  16. King County Metro Battery Electric Bus Demonstration: Preliminary Project Results

    Energy Technology Data Exchange (ETDEWEB)

    2017-05-22

    The U.S. Federal Transit Administration (FTA) funds a variety of research projects that support the commercialization of zero-emission bus technology. To evaluate projects funded through these programs, FTA has enlisted the help of the National Renewable Energy Laboratory (NREL) to conduct third-party evaluations of the technologies deployed under the FTA programs. NREL works with the selected agencies to evaluate the performance of the zero-emission buses compared to baseline conventional buses in similar service. The evaluation effort will advance the knowledge base of zero-emission technologies in transit bus applications and provide 'lessons learned' to aid other fleets in incrementally introducing next generation zero-emission buses into their operations. This report provides preliminary performance evaluation results from a demonstration of three zero-emission battery electric buses at King County Metro in King County, Washington. NREL developed this preliminary results report to quickly disseminate evaluation results to stakeholders. Detailed evaluation results will be published in future reports.

  17. Operational efficiency of the lighting system of bus salons

    Directory of Open Access Journals (Sweden)

    Brytkovskyi V.M.

    2016-08-01

    Full Text Available In recent years the problem of safety of people is studied primarily in aspects of natural and man-made disasters, fire, health and safety in the workplace. A problem connected with the way of life of the people, in particular with the use of bus transport remains almost out of sight. In addition to the foregoing, there is another side to the issue: modern development of industry and transport is characterized by large-scale introduction of technical measures aimed at saving energy In the specified aspect theoretical dependences for evaluation of technological economic efficiency of light sources in indoor lighting system buses are grounded. This theoretical dependency will make analytical framework justification applying the respective sources of light, taking into account the hygiene requirements to illumination. The methodology of calculation of economic efficiency of lighting of bus salons is offered. Estimating parameter is justified relative objective function value costs per unit of time or distance. The greatest costs are typical for lamps with incandescent bulbs. The least is common to lamps with fluorescent lamps. Led bulbs have no significant advantage even over incandescent lamps. The reason for this is the relatively high color temperature radiation of LED lamps that requires more light levels and, consequently, the high cost of energy, as well as relatively large initial cost of these lamps.

  18. Design of a steering stabilizer based on CAN bus

    Science.gov (United States)

    Zhan, Zhaomin; Yan, Yibin

    2018-04-01

    This design realizes a posture correction device of griping steering wheel based on CAN bus, which is embedded in the steering wheel of vehicles. The system aims to detect the drivers' abnormal griping postures and provides drivers with classification alerts, by combining the recorded griping postures data and the vehicle speed data that are obtained via the CAN bus. The warning information are automatically stored and retained in the device for 12 months. To enhance the alerting effect, the count of this warning message for both the latest month and the last 12 months are displayed on the dashboard panel. In addition to prevent itself from being blocked and self-detect any faults in advance, the appliance also provide a self-test function, which will communicate with the integrated instrument system in vehicle and do simulation test right after the vehicle power on. This appliance can help to urge and ensure drivers to operate the steering wheel correctly, effectively, and timely; prevent some typical incorrect behaviors which commonly happen along with the change of griping postures, such as the using cellphone, and ultimately, reduce the incidence of traffic accidents.

  19. Development of a multi-mode hybrid electric bus

    Energy Technology Data Exchange (ETDEWEB)

    Shemmans, M.J. [Overland Custom Coach, Thorndale, ON (Canada); Bland, C. [BET Services Inc., Mississauga, ON (Canada)

    2004-04-01

    This paper describes the development of an energy efficient, low floor, 28 foot hybrid electric bus for use as an airport shuttle bus or other specialized transit operations. A multi-mode concept was also adopted to include the capability of operating in battery-only drive, engine-only drive or a range of hybrid electric drive modes. The electric drivetrain was powered by a battery pack or a combination of a battery pack and an internal combustion engine-powered electric generator. The participating companies in this project include Overland Custom Coach, BET Services Inc., Siemens and Transport Canada. The technical feasibility study was described with reference to duty cycles, performance issues, vehicle weight, mechanical drive issues, brakes, suspension, powertrain cooling, heating, ventilation, electrical system, batteries and control system. The commercial feasibility was also described in terms of capital and operating costs. Results of the prototype tests validate the possibilities of zero or reduced emission transit in real world applications. 25 tabs., 32 figs.

  20. Studying customer loyalty at Daewoo express bus service, Pakistan

    Directory of Open Access Journals (Sweden)

    Usman Yousaf

    2013-09-01

    Full Text Available Background: Meeting service quality standards and striving for loyalty are two critical areas which have until now been overlooked by both the passenger transport industry and academia in Pakistan therefore the study sheds useful light on an issue hitherto untouched. Therefore increased sample size will help in increasing generalizability of study. Methods: This paper is designed to study the level of loyalty at Daewoo Express Bus Service in Sargodha by measuring customer satisfaction. Researchers used a small sample of only 96 respondents (passengers and only studies customer's behavior in the service quality of Daewoo Express Bus Service however it may differ in other passenger transport services. Results and conclusions: This paper reveals that there is a positive and significant relationship between loyalty (dependant variable and price perceptions, reliability, retrieving and smoothing (independent variables. However, the study found that reliability of services is the most important dimension among other independent variables (price perceptions, smoothing, reliability, retrieving effecting customers loyalty at Daewoo Express. Paper under consideration would surely assist Daewoo`s management team to take care of the loopholes existing in the current service level and likely threats which Daewoo might face.

  1. CERPEN FARUK “BUS KOTA” DALAM SEMIOTIK ROLAND BARTHES

    Directory of Open Access Journals (Sweden)

    Ken Widyatwati

    2016-04-01

    Full Text Available Literature called beautiful if it contains the mandate, message, ideas and meanings that are useful for the readers. Short story “Bus Kota” (City Bus containing the mandate, message, ideas and meanings that are useful to the reader. The mandate will be revealed by Roland Barthes' semiotic theory in the book S/Z. Literature has its own allure and text have accrued but not due to independence because of the difference in quality. Texts merge into a unity, or restore any text not as an individual but as a form of plurality. Literature as part of a social system is an expression of the author's sense of the outpouring of public life. Literary works can express themselves in the author's view the social and cultural changes in society because of the development of information technology and rapid. Technological developments and socio-cultural information can change in society so as to affect the psychology of the people. Society must have a thickness of faith not only for themselves, but to be able to maintain equanimity in the life of a pluralistic society

  2. A fuel cell city bus with three drivetrain configurations

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Junping [Key Laboratory of Education Ministry for Modern Design and Rotor-Bearing System, Xi' an Jiaotong University, Xi' an 710049 (China); Chen, Yong [School of Automobile and Transporting Engineering, Liaoning Institute of Technology, Jinzhou, Liaoning 121001 (China); Chen, Quanshi [State Key Laboratory of Automobile Safety and Energy Conservation, Tsinghua University, Beijing 100084 (China)

    2006-09-22

    Three fuel cell city buses of the energy hybrid- and power hybrid-type were re-engineered with three types of drivetrain configuration to optimize the structure and improve the performance. The energy distribution, hydrogen consumption, state of charge (SOC) and the power variation rate were analyzed when different drivetrain configurations and parameters were used. When powered only by a fuel cell, the bus cannot recover the energy through regenerative braking. The variation of the fuel cell power is large and frequent, which is not good for the fuel cell. When the fuel cell is linked to a battery pack in parallel, the bus can recover the energy through regenerative braking. The energy distribution is determined by the parameters of the fuel cell and the battery pack in the design stage to reduce the power variation rate of the fuel cell. When the fuel cell and DC/DC converter connected in series links the battery pack in parallel, energy can be recovered and the energy distribution can be adjusted online. The power variation rate of both the fuel cell and the battery pack are reduced. (author)

  3. Channel access: A software bus for the LAACS

    International Nuclear Information System (INIS)

    Hill, J.O.

    1990-01-01

    The host processor for a code running within a distributed process control system is often predetermined by constraints built into the software architecture of the control system. Input/output (I/O) channels directly connected to the host processors are usually easier to access in software than channels on remote processors. It is often difficult to modernize selective parts of a control system's software while leaving the other parts unchanged. Likewise, software developed at one laboratory is often difficult to integrate into a control system developed at another laboratory. Software that runs in one machine or operating-system architecture is often unable to communicate with control-system software running on a different platform. For the Los Alamos Accelerator Control System (LAACS) we have attempted to address the above difficulties with a software communication facility which we call Channel Access. Channel Access provides a 'software bus' that allows programs to be connected through a network to I/O channels on real-time processors in a manner similar to the way in which hardware modules are integrated within a standardized hardware bus such as CAMAC or VME. We have already placed an operator interface on Channel Access and we are currently designing alarm, archiving and sequencing tools as well. Numerous application-specific programs use Channel Access. This paper describes the unique feature of this approach and its performance as an integral part of the Los Alamos Accelerator Control System. (orig.)

  4. Particulate air pollution and vascular reactivity: the bus stop study.

    Science.gov (United States)

    Dales, Robert; Liu, Ling; Szyszkowicz, Mietek; Dalipaj, Mary; Willey, Jeff; Kulka, Ryan; Ruddy, Terrence D

    2007-11-01

    Particulate air pollution is associated with cardiovascular morbidity but mechanisms are not well understood. We tested the effects on vascular reactivity of exposure to fine particulates matter mass (PM(2.5)), number of particles bus stops. Flow-mediated vasodilation (FMD) of the brachial artery was then measured by ultrasound and expressed as: (maximum artery diameter after release of a blood pressure cuff inflated above systolic pressure-baseline resting diameter)/baseline resting diameter. A 30 microg/m(3) increase in PM(2.5) exposure corresponded to a 0.48% reduction in FMD, P=0.05 representing a 5% relative change in the maximum ability to dilate. Results were consistent between the two bus stops and not sensitive to type of analysis. No significant association was found between FMD and NO(2), PM(1.0) or traffic density. PM(2.5) may reduce the capacity to vasodilate, a potential explanation for the documented association with cardiovascular morbidity.

  5. Diesel bus emissions measured in a tunnel study.

    Science.gov (United States)

    Jamriska, Milan; Morawska, Lidia; Thomas, Steven; He, Congrong

    2004-12-15

    The emission factors of a bus fleet consisting of approximately 300 diesel-powered buses were measured in a tunnel study under well-controlled conditions during a 2-d monitoring campaign in Brisbane. Particle number and mass concentration levels of submicrometer particles and PM2.5 were monitored by SMPS and DustTrak instruments at the tunnel's entrance and exit, respectively. Correlation between DustTrak and TEOM response to diesel emissions was assessed, and the DustTrak results were recalculated into TEOM equivalent data. The mean value of the number and mass emission factors was (3.11+/-2.41) x 10(14) particles km(-1) for submicrometer particles and 583+/-451 mg km(-1) for PM2.5 (DustTrak), respectively. TEOM PM2.5 equivalent emission factor was 267+/-207 mg km(-1). The results are in good agreement with the emission factors determined from steady-state dynamometer testing of 12 buses from the same Brisbane City bus fleet. The results indicate that when carefully designed, both approaches, the dynamometer and on-road studies, can provide comparable results, applicable for the assessment of the effect of traffic emissions on airborne particle pollution. A brief overview of emission factors determined from other on-road and dynamometer studies reported in the literature as well as with the regulatory values used for the vehicle emission inventory assessment is presented and compared with the results obtained in this study.

  6. Bus Implementation Using New Low Power PFSCL Tristate Buffers

    Directory of Open Access Journals (Sweden)

    Neeta Pandey

    2016-01-01

    Full Text Available This paper proposes new positive feedback source coupled logic (PFSCL tristate buffers suited to bus applications. The proposed buffers use switch to attain high impedance state and modify the load or the current source section. An interesting consequence of this is overall reduction in the power consumption. The proposed tristate buffers consume half the power compared to the available switch based counterpart. The issues with available PFSCL tristate buffers based bus implementation are identified and benefits of employing the proposed tristate buffer topologies are put forward. SPICE simulation results using TSMC 180 nm CMOS technology parameters are included to support the theoretical formulations. The performance of proposed tristate buffer topologies is examined on the basis of propagation delay, output enable time, and power consumption. It is found that one of the proposed tristate buffer topology outperforms the others in terms of all the performance parameters. An examination of behavior of available and the proposed PFSCL tristate buffer topologies under parameter variations and mismatch shows a maximum variation of 14%.

  7. School Bus Transportation of Children With Special Health Care Needs.

    Science.gov (United States)

    O'Neil, Joseph; Hoffman, Benjamin D

    2018-05-01

    School systems are responsible for ensuring that children with special needs are safely transported on all forms of federally approved transportation provided by the school system. A plan to provide the most current and proper support to children with special transportation needs should be developed by the Individualized Education Program team, including the parent, school transportation director, and school nurse, in conjunction with physician orders and recommendations. With this statement, we provide current guidance for the protection of child passengers with specific health care needs. Guidance that applies to general school transportation should be followed, inclusive of staff training, provision of nurses or aides if needed, and establishment of a written emergency evacuation plan as well as a comprehensive infection control program. Researchers provide the basis for recommendations concerning occupant securement for children in wheelchairs and children with other special needs who are transported on a school bus. Pediatricians can help their patients by being aware of guidance for restraint systems for children with special needs and by remaining informed of new resources. Pediatricians can also play an important role at the state and local level in the development of school bus specifications. Copyright © 2018 by the American Academy of Pediatrics.

  8. Activities of four bus terminals of Semarang City gateway and the related GHG emission

    Science.gov (United States)

    Huboyo, H. S.; Wardhana, I. W.; Sutrisno, E.; Wangi, L. S.; Lina, R. A.

    2018-01-01

    The activities of the bus terminal, including loading-unloading passengers, bus idling, and bus movements at the terminal, will emit GHG’s emission. This research analyzes GHG emission from four terminals, i.e., Mangkang, Terboyo, Penggaron, and Sukun in Semarang City. The emission was estimated by observing detail activities of public transport means, especially for moving and idling time. The emission was calculated by Tier 2 method based on the vehicle type as well as fuel consumption. The highest CO2e during vehicle movements at Sukun area was contributed by large bus about 2.08 tons/year, while at Terboyo terminal was contributed by medium bus about 347.97 tons/year. At Mangkang terminals, the highest emission for vehicle movements was attributed by medium bus as well of about 53.18 tons/year. At last, Penggaron terminal’s highest GHG emission was attributed by BRT about 26.47 tons/year. During idling time, the highest contributor to CO2e was the large bus at the three terminals, i.e., Sukun of 43.53 tons/year, Terboyo of 196.56 tons/year, and Mangkang of 84.26 tons/year, while at Penggaron, BRT dominated with CO2e of 26.47 tons/year. The management of public transport in terminals is crucial to mitigate the emission related to bus terminals activities.

  9. 77 FR 74452 - Bus Testing: Calculation of Average Passenger Weight and Test Vehicle Weight

    Science.gov (United States)

    2012-12-14

    ... require FTA to work with bus manufacturers and transit agencies to establish a new pass/ fail standard for... buses from the current value of 150 pounds to a new value of 175 pounds. This increase was proposed to... new pass/fail standards that require a more comprehensive review of its overall bus testing program...

  10. Successfulness of bus rapid transit systems in Asia. Ex-post evaluation

    NARCIS (Netherlands)

    Kogdenko, Nadja

    2010-01-01

    SUMMARY Bus Rapid Transit (BRT) can be defined as “a bus-based mass transit system that delivers fast, comfortable, and cost-effective urban mobility”. It offers the opportunity to create a high-quality mass transit system at affordable costs, which is p

  11. For Safety and Sanity's Sake, Help Bus Drivers Keep Peace on the Ride to School.

    Science.gov (United States)

    Trotter, Andrew

    1987-01-01

    Outlines common-sense tips for disciplining student bus riders that are recommended by several driver-training programs. Themes include the following: (1) Set a few clear rules for proper bus behavior; (2) be positive; and (3) establish amiable communication with the children and with the principal as well. (CJH)

  12. Converter Power Density Increase using Low Inductive Integrated DC-link Capacitor/Bus

    DEFF Research Database (Denmark)

    Trintis, Ionut; Franke, Toke; Rannested, Bjørn

    2015-01-01

    The power losses in switching devices have a direct effect on the maximum converter power. For a voltage source converter, the DC-link bus has a major influence on the power loss and safe operating area of the power devices. The Power Ring Film CapacitorTM integrated with an optimized bus structu...

  13. Evoking Emotions and Unpacking Layered Histories through Young Children's Illustrations of Racial Bus Segregation

    Science.gov (United States)

    Kuby, Candace R.

    2013-01-01

    Drawing on theories of multi-modality and critical visual literacy, this article focuses on images that five-and six year-olds painted in a class-made book, Voice on the Bus, about racial segregation. The article discusses how children used illustrations to convey their understandings of Rosa Parks' bus arrest in Alabama. A post-structural view…

  14. Bus Operation Monitoring Oriented Public Transit Travel Index System and Calculation Models

    Directory of Open Access Journals (Sweden)

    Jiancheng Weng

    2013-01-01

    Full Text Available This study proposed a two-dimensional index system which is concerned essentially with urban travel based on travel modes and user satisfaction. First, the public transit was taken as an example to describe the index system establishing process. In consideration of convenience, rapid, reliability, comfort, and safety, a bus service evaluation index system was established. The indicators include the N-minute coverage of bus stops, average travel speed, and fluctuation of travel time between stops and bus load factor which could intuitively describe the characteristics of public transport selected to calculate bus travel indexes. Then, combined with the basic indicators, the calculation models of Convenience Index (CI, Rapid Index (RI, Reliability Index (RBI, and Comfort Index (CTI were established based on the multisource data of public transit including the real-time bus GPS data and passenger IC card data. Finally, a case study of Beijing bus operation evaluation and analysis was conducted by taking real bus operation data including GPS data and passenger transaction recorder (IC card data. The results showed that the operation condition of the public transit was well reflected and scientifically classified by the bus travel index models.

  15. Air flow through a non-airconditioned bus with open windows

    Indian Academy of Sciences (India)

    Thus, bus travel which is the backbone of public transport in India will continue ... was not possible to replicate the same Reynolds number as in a real bus. With the .... The Kolmogorov time scale, τη can be estimated to be 6 × 10. −3 s. Thus ...

  16. Operating Time Division for a Bus Route Based on the Recovery of GPS Data

    Directory of Open Access Journals (Sweden)

    Jian Wang

    2017-01-01

    Full Text Available Bus travel time is an important source of data for time of day partition of the bus route. However, in practice, a bus driver may deliberately speed up or slow down on route so as to follow the predetermined timetable. The raw GPS data collected by the GPS device equipped on the bus, as a result, cannot reflect its real operating conditions. To address this concern, this study first develops a method to identify whether there is deliberate speed-up or slow-down movement of a bus. Building upon the relationships between the intersection delay, link travel time, and traffic flow, a recovery method is established for calculating the real bus travel time. Using the dwell time at each stop and the recovered travel time between each of them as the division indexes, a sequential clustering-based time of day partition method is proposed. The effectiveness of the developed method is demonstrated using the data of bus route 63 in Harbin, China. Results show that the partition method can help bus enterprises to design reasonable time of day intervals and significantly improve their level of service.

  17. Study on the optimum design of bus window pillar join40t; Bus window pillar ketsugo buzai no saiteki sekkei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Tomioka, N [Nihon University, Tokyo (Japan); Lim, S; Kim, M; Lee, H; Kang, S; Bae, D

    1997-10-01

    Automobile body structure is generally assembled using various spot welded box sectional members. Especially, in the case of the bus, the shape of window pillar joint is assembled m T-type. This T-type member has some problem such as high stress concentration, low fatigue strength and structural rigidity. Therefore, in this report, performed a study on the optimum design of the bus window pillar joint for such problem by FEM analysis and experiments. 1 ref., 10 figs., 2 tabs.

  18. A Study of BUS Architecture Design for Controller of Nuclear Power Plant Using FPGA

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Dongil; Yun, Donghwa; Hwang, Sungjae; Kim, Myeongyun; Lee, Dongyun [PONUTech Co. Ltd., Seoul (Korea, Republic of)

    2014-05-15

    CPU (Central Processing Unit) operating speed and communication rate have been more technically improved than before. However, whole system is been a degradation of performance by electronic and structural limitation of parallel bus. Transmission quantity and speed have a limit and need arbiter in order to do arbitration because several boards shared parallel bus. Arbiter is a high complexity in implementing so it increases component per chip. If a parallel bus uses, it will occurs some problems what are reflection noise, power/ground noise (or ground bounce) as SSN (Simultaneous Switching Noise) and crosstalk noise like magnetic coupling. In this paper, in order to solve a problem of parallel bus in controller of NPP (Nuclear Power Plant), proposes the bus architecture design using FPGA (Field Programmable Gate Array) based on LVDS (Low Voltage Differential Signaling)

  19. A Study of BUS Architecture Design for Controller of Nuclear Power Plant Using FPGA

    International Nuclear Information System (INIS)

    Lee, Dongil; Yun, Donghwa; Hwang, Sungjae; Kim, Myeongyun; Lee, Dongyun

    2014-01-01

    CPU (Central Processing Unit) operating speed and communication rate have been more technically improved than before. However, whole system is been a degradation of performance by electronic and structural limitation of parallel bus. Transmission quantity and speed have a limit and need arbiter in order to do arbitration because several boards shared parallel bus. Arbiter is a high complexity in implementing so it increases component per chip. If a parallel bus uses, it will occurs some problems what are reflection noise, power/ground noise (or ground bounce) as SSN (Simultaneous Switching Noise) and crosstalk noise like magnetic coupling. In this paper, in order to solve a problem of parallel bus in controller of NPP (Nuclear Power Plant), proposes the bus architecture design using FPGA (Field Programmable Gate Array) based on LVDS (Low Voltage Differential Signaling)

  20. Active Power Filter DC Bus Voltage Piecewise Reaching Law Variable Structure Control

    Directory of Open Access Journals (Sweden)

    Baolian Liu

    2014-01-01

    Full Text Available The DC bus voltage stability control is one key technology to ensure that Active Power Filter (APF operates stably. The external disturbances such as power grid and load fluctuation and the system parameters changing may affect the stability of APF DC bus voltage and the normal operation of APF. The mathematical model of DC bus voltage is established according to power balance principle and a DC bus voltage piecewise reaching law variable structure control algorithm is proposed to solve the above problem, and the design method is given. The simulation and experiment results proved that the proposed variable structure control algorithm can eliminate the chattering problem existing in traditional variable structure control effectively, is insensitive to system disturbance, and has good robustness and fast dynamic response speed and stable DC bus voltage with small fluctuation. The above advantages ensure the compensation effect of APF.

  1. Bus driving assistance system for town area by using ATmega328P microcontroller

    Science.gov (United States)

    Zakaria, Mohamad Fauzi; Soon, Tan Jiah; Rohani, Munzilah Md

    2017-09-01

    Recently, several bus accidents happened because of bus driver's behavior. In fact, there is no dedicated tool for assisting them to drive safely. This project gives solutions to this by assisting the driver, according to the speed and acceleration of the bus. These data are collected by using a motion processing unit (MPU-6050) and a global positioning system (GPS) and then indicate the driving mode status on the LEDs. All data and status are recorded in a secure digital (SD) card for the authority or the bus company to analyze the driving behavior of a bus driver. This system has been successfully developed and tested in two different areas which includes the UTHM main campus and the road from Parit Raja to Batu Pahat.

  2. Integrated Optimization of Bus Line Fare and Operational Strategies Using Elastic Demand

    Directory of Open Access Journals (Sweden)

    Chunyan Tang

    2017-01-01

    Full Text Available An optimization approach for designing a transit service system is proposed. Its objective would be the maximization of total social welfare, by providing a profitable fare structure and tailoring operational strategies to passenger demand. These operational strategies include full route operation (FRO, limited stop, short turn, and a mix of the latter two strategies. The demand function is formulated to reflect the attributes of these strategies, in-vehicle crowding, and fare effects on demand variation. The fare is either a flat fare or a differential fare structure; the latter is based on trip distance and achieved service levels. This proposed methodology is applied to a case study of Dalian, China. The optimal results indicate that an optimal combination of operational strategies integrated with a differential fare structure results in the highest potential for increasing total social welfare, if the value of parameter ε related to additional service fee is low. When this value increases up to more than a threshold, strategies with a flat fare show greater benefits. If this value increases beyond yet another threshold, the use of skipped stop strategies is not recommended.

  3. Assessment of Passenger Satisfaction with Public Bus Transport Services: A Case Study of Lucknow City (India

    Directory of Open Access Journals (Sweden)

    Singh Sanjay

    2016-12-01

    Full Text Available The main aim of this study is threefold. First, it tries to assess the passenger satisfaction with public bus transport services in the city of Lucknow in India. Second, it tries to examine the service quality attributes that influence the passenger satisfaction. Third, it tries to evaluate the relative importance of service quality attributes to find out the priority for service quality improvements to enhance passenger satisfaction. The study is based on a survey of objective as well as subjective questions conducted between May and July 2014. Five major bus stops of Lucknow were selected for the survey. Total 148 respondents were randomly selected to elicit their overall satisfaction and factors that influence their satisfaction in the use of public bus transport services in Lucknow using a self-rated questionnaire. The collected sample of responses is subjected to principal component analysis, a statistical technique for dimensionality reduction of the dataset, and descriptive analysis. The result of theses analyses shows that passengers are mostly dissatisfied with public bus transport services in Lucknow. Using principal component analysis, five underlying factors were extracted that influenced passenger satisfaction with public bus transport services in the city. Out of these five factors, comfort and safety has the greatest impact on overall satisfaction, followed by the adequacy of capacity of public bus transport services, orderly and clean environment inside buses, elegant design of buses and bus stops, and accessibility to public bus transport services in the city. The study thus provides a direction for public bus transport administration in the city to understand the gaps that exist and try to fill them to improve its services so that passenger satisfaction can be enhanced and consequently more people can be attracted towards public bus transport.

  4. Mars Comm/Nav MicroSat Network Using the Multi-Mission Bus Launched Piggyback by Ariane 5

    Science.gov (United States)

    Hastrup, R. C.; Cesarone, R. J.; Morabito, D. D.

    1999-01-01

    Recently, NASA's Jet Propulsion Laboratory completed a Mars Exploration Program Architecture Definition Study with strong international participation. The recommendations of this study include establishment of a low cost in-situ communications and navigation satellite network to provide enabling and enhancing support for the international exploration of Mars. This would be the first step toward establishing a "virtual presence throughout the solar system" as called for in NASA's Strategic Plan. Response to the proposed comm/nav satellite network has been very favorably received, as reflected by the inclusion of a line item in NASA's budget submittal to Congress, which provides funding for implementation of the network with first launch in the 2003 opportunity. Funding has already been provided for a phase A study being conducted this year. This paper presents the planned implementation of the comm/nav network, which will utilize microsats based on a multi-mission spacecraft bus being designed for launch by the Ariane 5 as a secondary payload. A companion paper at this conference, entitled "The Multi-Purpose Mars Micro-Mission System Design Utilizing Ariane 5 Piggyback Launch", describes the multimission bus design. This paper addresses the application of the multi-mission bus to the comm/nav microsat mission. Following an introduction, which provides the background that has led to the proposed comm/nav network, the paper discusses the projected user needs with emphasis on the various possible robotic missions (landers, rovers, ascent vehicles, balloons, aircraft, etc.) progressing toward eventual piloted missions. Next, the paper describes the concept for an evolving network of comm/nav microsats and the expected capability to satisfy the user needs. Results of communications and navigation performance analysis are summarized for attractive satellite constellation configurations. The important comm/nav microsat functional requirements on the multi

  5. 49 CFR 37.169 - Interim requirements for over-the-road bus service operated by private entities.

    Science.gov (United States)

    2010-10-01

    ... of such devices, shall be permitted in the passenger compartment. When the bus is at rest at a stop... 49 Transportation 1 2010-10-01 2010-10-01 false Interim requirements for over-the-road bus service... Interim requirements for over-the-road bus service operated by private entities. (a) Private entities...

  6. Tinjauan Yuridis Perjanjian Kerjasama Pengadaan Armada Kendaraan Bus Wisata Antara PT. Lingga Jati Al Manshurin Dengan P.O. Karona

    OpenAIRE

    Sinabang, Rajamin P.

    2010-01-01

    Perkembangan masyarakat telah dipengaruhi oleh kemajuan teknologi. Hal ini yang memperbaharui penggunaan berbagai aturan hukum untuk bentuk-bentuk tertentu, hingga sampai pada bentuk pelayanan (service) tertentu dari pengusaha dalam bidang teknologi, khususnya dalam usaha pengangkutan darat. Sehingga dibutuhkan bus dari perusahaan penyedia armada kendaraan bus untuk pengangkutan tersebut, yaitu melalui perjanjian kerjasama pengadaan armada bus, yang dilakukan oleh PT. Lingga Jati Al Manshurin...

  7. 40 CFR 85.1404 - Maintenance of records for urban bus operators; submittal of information; right of entry.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Maintenance of records for urban bus... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Urban Bus Rebuild Requirements § 85.1404 Maintenance of records for urban bus operators; submittal...

  8. Heat generation by eddy currents in a shell of superconducting bus-bars for SIS100 particle accelerator at FAIR

    Directory of Open Access Journals (Sweden)

    Tomków Łukasz

    2017-12-01

    Full Text Available Superconducting magnets in the SIS100 particle accelerator require the supply of liquid helium and electric current. Both are transported with by-pass lines designed at Wrocław University of Technology. Bus-bars used to transfer an electric current between the sections of the accelerator will be encased in a steel shell. Eddy currents are expected to appear in the shell during fast-ramp operation of magnets. Heat generation, which should be limited in any cryogenic system, will appear in the shell. In this work the amount of heat generated is assessed depending on the geometry of an assembly of the bus-bars and the shell. Numerical and analytical calculations are described. It was found that heat generation in the shell is relatively small when compared to other sources present in the accelerator and its value strongly depends on the geometry of the shell. The distribution of eddy currents and generated heat for different geometrical options are presented. Based on the results of the calculations the optimal design is proposed.

  9. Experimental Results of a DC Bus Voltage Level Control for a Load-Controlled Marine Current Energy Converter

    Directory of Open Access Journals (Sweden)

    Johan Forslund

    2015-05-01

    Full Text Available This paper investigates three load control methods for a  marine current energy converter using a vertical axis current  turbine (VACT mounted on a permanent magnet synchronous generator  (PMSG. The three cases are; a fixed AC load, a fixed pulse width  modulated (PWM DC load and DC bus voltage control of a DC  load. Experimental results show that the DC bus voltage control  reduces the variations of rotational speed by a factor of 3.5 at the cost  of slightly increased losses in the generator and transmission lines.  For all three cases, the tip speed ratio \\(\\lambda\\ can be kept close to  the expected \\(\\lambda_{opt}\\. The power coefficient is estimated to be  0.36 at \\(\\lambda_{opt}\\; however, for all three cases, the average  extracted power was about \\(\\sim 19\\\\%. A maximum power point  tracking (MPPT system, with or without water velocity measurement,  could increase the average extracted power.

  10. Concentrations of polycyclic aromatic hydrocarbons in resuspendable fraction of settled bus dust and its implications for human exposure.

    Science.gov (United States)

    Gao, Peng; Liu, Sa; Feng, Yujie; Lin, Nan; Lu, Binyu; Zhang, Zhaohan; Cui, Fuyi; Xing, Baoshan; Hammond, S Katharine

    2015-03-01

    This preliminary study measured Polycyclic Aromatic Hydrocarbons (PAHs) concentrations in the resuspendable fraction of settled dust on 39 bus lines, to evaluate the impact of engine type (gasoline and compressed natural gas) on exposure for commuters and drivers. Benzo(b)fluoranthene(BbF) was the predominant PAH in resuspendable fraction of settled bus dust. The concentration of total PAHs was 92.90 ± 116.00 μg/g (range: 0.57-410) in gasoline buses and 3.97 ± 1.81 (range: 2.01-9.47) in compressed natural gas (CNG) buses. Based on Benzo[a]pyrene (BaP) equivalent concentrations for the sum of 16 PAHs, the average daily dose (ADD) via dust ingestion and dermal contact was calculated. The ADD of PAHs was higher for commuters and drivers in gasoline-powered buses than in buses using CNG buses. For both short and long duration journeys, young commuters were exposed to higher levels of PAHs via dust ingestion and dermal contact than adult commuters. Copyright © 2014 Elsevier Ltd. All rights reserved.

  11. Bluetooth wireless monitoring, diagnosis and calibration interface for control system of fuel cell bus in Olympic demonstration

    Energy Technology Data Exchange (ETDEWEB)

    Hua, Jianfeng; Lin, Xinfan; Xu, Liangfei; Li, Jianqiu; Ouyang, Minggao [Tsinghua University, State Key Laboratory of Automotive Safety and Energy, Beijing100084 (China)

    2009-01-15

    With the worldwide deterioration of the natural environment and the fossil fuel crisis, the possible commercialization of fuel cell vehicles has become a hot topic. In July 2008, Beijing started a clean public transportation plan for the 29th Olympic games. Three fuel cell city buses and 497 other low-emission vehicles are now serving the Olympic core area and Beijing urban areas. The fuel cell buses will operate along a fixed bus line for 1 year as a public demonstration of green energy vehicles. Due to the specialized nature of fuel cell engines and electrified power-train systems, measurement, monitoring and calibration devices are indispensable. Based on the latest Bluetooth wireless technology, a novel Bluetooth universal data interface was developed for the control system of the fuel cell city bus. On this platform, a series of wireless portable control auxiliary systems have been implemented, including wireless calibration, a monitoring system and an in-system programming platform, all of which are ensuring normal operation of the fuel cell buses used in the demonstration. (author)

  12. Oxidative and nitrosative stress markers in bus drivers.

    Science.gov (United States)

    Rossner, Pavel; Svecova, Vlasta; Milcova, Alena; Lnenickova, Zdena; Solansky, Ivo; Santella, Regina M; Sram, Radim J

    2007-04-01

    Exposure to ambient air pollution is associated with many diseases. Oxidative and nitrosative stress are believed to be two of the major sources of particulate matter (PM)-mediated adverse health effects. PM in ambient air arises from industry, local heating, and vehicle emissions and poses a serious problem mainly in large cities. In the present study we analyzed the level of oxidative and nitrosative stress among 50 bus drivers from Prague, Czech Republic, and 50 matching controls. We assessed simultaneously the levels of 15-F(2t)-isoprostane (15-F(2t)-IsoP) and 8-oxodeoxyguanosine (8-oxodG) in urine and protein carbonyl groups and 3-nitrotyrosine (NT) in blood plasma. For the analysis of all four markers we used ELISA techniques. We observed significantly increased levels of oxidative and nitrosative stress markers in bus drivers. The median levels (min, max) of individual markers in bus drivers versus controls were as follows: 8-oxodG: 7.79 (2.64-12.34)nmol/mmol versus 6.12 (0.70-11.38)nmol/mmol creatinine (p<0.01); 15-F(2t)-IsoP: 0.81 (0.38-1.55)nmol/mmol versus 0.68 (0.39-1.79)nmol/mmol creatinine (p<0.01); carbonyl levels: 14.1 (11.8-19.0)nmol/ml versus 12.9 (9.8-16.6)nmol/ml plasma (p<0.001); NT: 694 (471-3228)nmol/l versus 537 (268-13833)nmol/l plasma (p<0.001). 15-F(2t)-IsoP levels correlated with vitamin E (R=0.23, p<0.05), vitamin C (R=-0.33, p<0.01) and cotinine (R=0.47, p<0.001) levels. Vitamin E levels also positively correlated with 8-oxodG (R=0.27, p=0.01) and protein carbonyl levels (R=0.32, p<0.001). Both oxidative and nitrosative stress markers positively correlated with PM2.5 and PM10 exposure. In conclusion, our study indicates that exposure to PM2.5 and PM10 results in increased oxidative and nitrosative stress.

  13. Integration of refrigerators into facility automation with the aid of bus systems; Integration der Kaeltetechnik in die Gebaeudeautomation mit Bus-Systemen

    Energy Technology Data Exchange (ETDEWEB)

    Baumgarth, S.; Heiser, M. [Fachhochschule Braunschweig-Wolfenbuettel, Wolfenbuettel (DE). Inst. fuer Verbrennungstechnik und Prozessautomation (IVP)

    2000-07-01

    The integration of refrigeration systems in building automation is illustrated by the example of a ventilation system and a cooling ceiling. Cold is supplied by a coldwater unit. This necessitates supply of consumption data to the central refrigeration system. So far, technical facilities are commonly controlled by DDC systems and in-house bus systems. The demand for open communication between different systems resulted in the development of neutral systems like FND and Profibus, which were followed by a multitude of other, less generally accepted systems. In the field of electrical installations, the European Installation Bus EIB was generally accepted as a certified, open bus system which can be combined with DDC technology and integrated in in-house control systems. Another technology developed in the USA is the Local Operating Network, LON, whic has a hither transmission rate and higher information content for the various bus members. The contribution compares the two bus systems. [German] Die Einbindung der Kaeltetechnik in die Gebaeudeautomation wird an den Beispielen Lueftungsanlage und Kuehldecke vorgestellt. Die erforderliche Kaelte soll durch einen Kaltwasserersatz energieoptimiert bereitgestellt werden. Dazu muessen Informationen aus dem Verbraucherbereich in der Kaeltezentrale zur Verfuegung stehen. RTL-Anlagen wurden bisher mittels DDC-Technik und firmenspezifischen Bus-Systemen geregelt und gesteuert. Wenn verschiedene Anlagen durch DDC-Systeme unterschiedlicher Hersteller betrieben wurden, so war anfaenglich eine gemeinsame Ueberwachung auf einer zentralen Leitwarte nur ueber Gateways moeglich. Aus der Forderung nach offener Kommunikation unterschiedlicher Systeme entstanden die ersten firmenneutralen Entwicklungen FND und Profibus. Es folgten eine Vielzahl weiterer Netz- und Busdefinitionen und deren Kommunikationsprotokolle, denen jedoch weitgehend eine allgemeine Anerkennung versagt blieb. Im Bereich der Elektroinstallation profilierte sich der

  14. Research on a Scania 11 liter ethanol fueled bus engine

    Energy Technology Data Exchange (ETDEWEB)

    Egebaeck, K E; Pettersson, E

    1996-05-01

    This report presents research carried out on an alcohol fueled bus engine. The engine used was a six cylinder 11 liter compression ignition turbo-charged engine with an inter cooler. The research program included studies of the impact on the emissions when changing different engine components and different settings of the engine. A study of the impact on the engine performance and emissions when using different fuel compositions was also carried out. During the course of the work, the engine was equipped with oxidation catalysts of two different types, one of which was more efficient than the other concerning the oxidation of unburnt fuel related components. One of the main purposes of the research was to improve the emission characteristics of the engine by an optimization of the engine and its setting. The exhaust emissions were thoroughly characterized with respect to both regulated and unregulated emissions. 13 refs, figs, tabs

  15. Optimum power quality service in multi-bus microgrid systems

    DEFF Research Database (Denmark)

    Meng, Lexuan; Guerrero, Josep M.

    2017-01-01

    Power quality requirements for different consumers and electric equipment are distinguished. Conventionally a common power quality standard is applied to the whole power grid inducing debate between several sides, including consumers, generation sites and technical commissions. Customized power...... quality standard settings for different consumers become a widely accepted solution. The main challenge is on the proper regulation of power quality in different areas. This paper considers a multi-bus microgrid system where the power quality in each has flexible and individual standard. Distributed...... generators are utilized to provide power quality regulation functions. An optimization method based strategy is proposed and implemented with the power converter control system. A general mathematical model is established which can be used in the optimization problem for evaluating the objective function...

  16. Multi Bus DC-DC Converter in Electric Hybrid Vehicles

    Science.gov (United States)

    Krithika, V.; Subramaniam, C.; Sridharan, R.; Geetha, A.

    2018-04-01

    This paper is cotncerned with the design, simulation and fabrication of the prototype of a Multi bus DC- DC converter operating from 42V DC and delivering 14V DC and 260V DC. As a result, three DC buses are interconnected through a single power electronic circuitry. Such a requirement is energized in the development of a hybrid electric automobile which uses the technology of fuel cell. This is implemented by using a Bidirectional DC-DC converter configuration which is ideally suitable for multiple outputs with mutual electrical isolation. For the sake of reduced size and cost of step-up transformer, selection of a high frequency switching cycle at 10 KHz was done.

  17. A fast ECL bus memory: dual input memory

    International Nuclear Information System (INIS)

    Cesaroni, F.; Pascale, G.; Gentile, S.; Gao, Z.

    1992-01-01

    A fast and flexible dual input memory (DIM) has been constructed as single CAMAC unit. The device has been designed to receive via front panel two 16-bit data words, which can be stored in sequential mode into a memory and, at the same time, presented on the output. The design implemented also the possibility to connect 16-bit differential ECL outputs of many DIMs modules on the same bus. Its timing characteristics for writing and reading into and from memory is only 20 ns. This makes the module a useful element for all kinds of fast acquisition systems, as tempory storage of data, or data source or spy module. It will be, for example, used in the new energy tripper of the L3 experiment, designed for 8x8 bunch mode operation of LEP in 1992. (orig.)

  18. FAIR: A new fast trigger and readout bus system

    International Nuclear Information System (INIS)

    Ordine, A.; Boiano, A.; Zaghi, A.

    1998-01-01

    FAIR (FAst Intercrate Readout) is a synchronous ECL bus system dedicated to readout. It is based on a new trigger and readout hardware level protocol and on a new control system that learns how to setup and control modules. The hardware protocol along with the data structure allow both readout and event building at the same time at the rate of 22 ns/longword (1.44 Gbit/s) without the need of CPUs. It performs trigger management and full pipelining by using a multilevel FIFO structure. FAIR provides for a multi-crate front-end environment and uses an embedded serial network to accomplish front-end control and setup. The data transfer measured performances and the control system are presented in some detail

  19. FAKTOR PENYEBAB KERUSAKAN SISTEM MESIN PADA BUS APTB PPD

    Directory of Open Access Journals (Sweden)

    Laela Chairani

    2015-06-01

    Full Text Available Comfort and safety of public transportation, particularly APTB PPD buses, becomes high expectations for its customers. Those expectations must be supported by the application of a good engine maintenance system. By using the method of Reliability Centered Maintenance may be determined appropriate actions to mitigate damage. From the analysis known the failures of the APTB PPD bus are malfunctions of the fuel engine, power transfer systems, difficulty to move the gear lever, and lubricating system for the rough engine noise. The cause of engine malfunction is dirty diesel filter, vehicle acceleration malfunction is due to the clutch plate wear out. Difficulty to move the gear lever indicates that the clutch slips. Rough engine noise caused by the flow of oil to the engine stalled as the result of dirty oil filter. The results of the logic tree analysis show that for each failure requires scheduling of time directed task.

  20. Kajian Implementasi Graph Database pada Rute Bus Rapid Transit

    Directory of Open Access Journals (Sweden)

    Panji Wisnu Wirawan

    2017-12-01

    Full Text Available Bus Rapid Transit (BRT merupakan salah satu sarana transportasi publik yang memiliki rute perjalanan tertentu atau disebut sebagai koridor. Satu koridor BRT dengan koridor yang lain bukanlah koridor yang terpisah, melainkan saling terhubung. Dalam melakukan perjalanan, penumpang BRT boleh jadi melakukan perpindahan koridor melalui shelter. Informasi tersebut perlu didapatkan seorang calon penumpang sebelum melakukan perjalanan supaya tidak terjadi perpindahan koridor yang salah. Teknologi informasi memungkinkan representasi informasi pencarian koridor yang tepat ketika penumpang akan melakukan sebuah perjalanan, terlebih dengan hadirnya graph database. Graph Database memungkinkan representasi BRT yang baik karena sifat graph yang secara standar telah menunjukkan node dan relationship. Artikel ini mengkaji penerapan graph database untuk data pada BRT. Selain itu, artikel ini mendesain sebuah algoritma pencarian koridor BRT. Harapannya, algoritma tersebut dapat digunakan untuk membangun aplikasi yang memanfaatkan data pada graph database. Hasil kajian menunjukkan bahwa graph database dapat diterapkan untuk data BRT dan algoritma yang dibangun dapat digunakan untuk menyajikan informasi rute sekaligus menyampaikan informasi perpindahan koridor.

  1. Using a Control System Ethernet Network as a Field Bus

    CERN Document Server

    De Van, William R; Lawson, Gregory S; Wagner, William H; Wantland, David M; Williams, Ernest

    2005-01-01

    A major component of a typical accelerator distributed control system (DCS) is a dedicated, large-scale local area communications network (LAN). The SNS EPICS-based control system uses a LAN based on the popular IEEE-802.3 set of standards (Ethernet). Since the control system network infrastructure is available throughout the facility, and since Ethernet-based controllers are readily available, it is tempting to use the control system LAN for "fieldbus" communications to low-level control devices (e.g. vacuum controllers; remote I/O). These devices may or may not be compatible with the high-level DCS protocols. This paper presents some of the benefits and risks of combining high-level DCS communications with low-level "field bus" communications on the same network, and describes measures taken at SNS to promote compatibility between devices connected to the control system network.

  2. Research on Community Structure in Bus Transport Networks

    International Nuclear Information System (INIS)

    Yang Xuhua; Wang Bo; Sun Youxian

    2009-01-01

    We abstract the bus transport networks (BTNs) to two kinds of complex networks with space L and space P methods respectively. Using improved community detecting algorithm (PKM agglomerative algorithm), we analyze the community property of two kinds of BTNs graphs. The results show that the BTNs graph described with space L method have obvious community property, but the other kind of BTNs graph described with space P method have not. The reason is that the BTNs graph described with space P method have the intense overlapping community property and general community division algorithms can not identify this kind of community structure. To overcome this problem, we propose a novel community structure called N-depth community and present a corresponding community detecting algorithm, which can detect overlapping community. Applying the novel community structure and detecting algorithm to a BTN evolution model described with space P, whose network property agrees well with real BTNs', we get obvious community property. (general)

  3. Foothill Transit Battery Electric Bus Demonstration Results: Second Report

    Energy Technology Data Exchange (ETDEWEB)

    Eudy, Leslie [National Renewable Energy Lab. (NREL), Golden, CO (United States); Jeffers, Matthew [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2017-06-28

    This report summarizes results of a battery electric bus (BEB) evaluation at Foothill Transit, located in the San Gabriel and Pomona Valley region of Los Angeles County, California. Foothill Transit is collaborating with the California Air Resources Board and the U.S. Department of Energy's (DOE's) National Renewable Energy Laboratory to evaluate its fleet of Proterra BEBs in revenue service. The focus of this evaluation is to compare performance of the BEBs to that of conventional technology and to track progress over time toward meeting performance targets. This project has also provided an opportunity for DOE to conduct a detailed evaluation of the BEBs and charging infrastructure. This is the second report summarizing the results of the BEB demonstration at Foothill Transit and it provides data on the buses from August 2015 through December 2016. Data are provided on a selection of compressed natural gas buses as a baseline comparison.

  4. Autonomous Navigation and Obstacle Avoidance of a Micro-Bus

    Directory of Open Access Journals (Sweden)

    Carlos Fernández

    2013-04-01

    Full Text Available At present, the topic of automated vehicles is one of the most promising research areas in the field of Intelligent Transportation Systems (ITS. The use of automated vehicles for public transportation also contributes to reductions in congestion levels and to improvements in traffic flow. Moreover, electrical public autonomous vehicles are environmentally friendly, provide better air quality and contribute to energy conservation. The driverless public transportation systems, which are at present operating in some airports and train stations, are restricted to dedicated roads and exhibit serious trouble dynamically avoiding obstacles in the trajectory. In this paper, an electric autonomous mini-bus is presented. All datasets used in this article were collected during the experiments carried out in the demonstration event of the 2012 IEEE Intelligent Vehicles Symposium that took place in Alcalá de Henares (Spain. The demonstration consisted of a route 725 metres long containing a list of latitude-longitude points (waypoints. The mini-bus was capable of driving autonomously from one waypoint to another using a GPS sensor. Furthermore, the vehicle is provided with a multi-beam Laser Imaging Detection and Ranging (LIDAR sensor for surrounding reconstruction and obstacle detection. When an obstacle is detected in the planned path, the planned route is modified in order to avoid the obstacle and continue its way to the end of the mission. On the demonstration day, a total of 196 attendees had the opportunity to get a ride on the vehicles. A total of 28 laps were successfully completed in full autonomous mode in a private circuit located in the National Institute for Aerospace Research (INTA, Spain. In other words, the system completed 20.3 km of driverless navigation and obstacle avoidance.

  5. Real-time bus location monitoring using Arduino

    Science.gov (United States)

    Ibrahim, Mohammad Y. M.; Audah, Lukman

    2017-09-01

    The Internet of Things (IoT) is the network of objects, such as a vehicles, mobile devices, and buildings that have electronic components, software, and network connectivity that enable them to collect data, run commands, and be controlled through the Internet. Controlling physical items from the Internet will increase efficiency and save time. The growing number of devices used by people increases the practicality of having IoT devices on the market. The IoT is also an opportunity to develop products that can save money and time and increase work efficiency. Initially, they need more efficiency for real-time bus location systems, especially in university campuses. This system can easily find the accurate locations of and distances between each bus stop and the estimated time to reach a new location. This system has been separated into two parts, which are the hardware and the software. The hardware parts are the Arduino Uno and the Global Positioning System (GPS), while Google Earth and GpsGate are the software parts. The GPS continuously takes input data from the satellite and stores the latitude and longitude values in the Arduino Uno. If we want to track the vehicle, we need to send the longitude and latitude as a message to the Google Earth software to convert these into maps for navigation. Once the Arduino Uno is activated, it takes the last received latitude and longitude positions' values from GpsGate and sends a message to Google Earth. Once the message has been sent to Google Earth, the current location will be shown, and navigation will be activated automatically. Then it will be broadcast using ManyCam, Google+ Hangouts, and YouTube, as well as Facebook, and appear to users. The additional features use Google Forms for determining problems faced by students, who can also take immediate action against the responsible department. Then after several successful simulations, the results will be shown in real time on a map.

  6. Analysis of Public Bus Transportation of a Brazilian City Based on the Theory of Complex Networks Using the P-Space

    Directory of Open Access Journals (Sweden)

    A. A. De Bona

    2016-01-01

    Full Text Available The city of Curitiba, located at Southern Brazil, is recognized by its urban planning structured on three pillars: land use, collective transportation, and traffic. With 3.8 million people in its metropolitan area, the public transport system deals with approximately 2.5 million passengers daily. The structure and properties of such a transportation system have substantial implications for the urban planning and public politics for sustainable development of Curitiba. Therefore, this paper analyzes the structure of the public transportation system of Curitiba through the theory of complex networks in a static approach of network topology and presents a comparative analysis of the results from Curitiba, three cities from China (Shanghai, Beijing, and Guangzhou, and three cities from Poland (GOP, Warszawa, and Łódź. The transportation network was modeled as a complex network with exact geographical coordinates of its bus stops. In all bus lines, the method used was the P-Space. The results show that this bus network has characteristics of both small-world and scale-free networks.

  7. Sliding-Mode Control of a Charger/Discharger DC/DC Converter for DC-Bus Regulation in Renewable Power Systems

    Directory of Open Access Journals (Sweden)

    Sergio Ignacio Serna-Garcés

    2016-03-01

    Full Text Available Stand-alone power systems based on renewable energy sources are used to replace generators based on fossil fuels. Those renewable power systems also require Energy Storage Devices (ESD interfaced by a charger/discharger power converter, which consist of a bidirectional DC/DC converter, and a DC bus. This paper proposes a single sliding-mode controller (SMC for the charger/discharger DC/DC converter to provide a stable DC bus voltage in any operation condition: charging or discharging the ESD, or even without any power exchange between the ESD and the DC bus. Due to the non-linear nature of the power converter, the SMC parameters are adapted on-line to ensure global stability in any operation condition. Such stability of the adaptive SMC is mathematically demonstrated using analytical expressions for the transversality, reachability and equivalent control conditions. Moreover, a design procedure for the adaptive SMC parameters is provided in order to ensure the dynamic response required for the correct operation of the load. Finally, simulations and experimental tests validate the proposed controller and design procedure.

  8. Comparison of the combustion engine operating parameters and the ecological indicators of an urban bus in dynamic type approval tests and in actual operating conditions

    Directory of Open Access Journals (Sweden)

    Rymaniak Lukasz

    2017-01-01

    Full Text Available The article presents the considerations regarding a city bus combustion engine performanceparameters in dynamic type approval tests and in real operating conditions when servicing an urban bus line. A comparison of the designated engine operating time shares with respect to load and crankshaft rotational speed was made. The analysis included the ETC and WHTC tests, which showed significant discrepancies in the work areas of internal combustion engines in these test when compared to actual driving conditions. The details of the type approval tests used and the method of their denormalization for the drive unit were presented. The vehicle used for this research was an eighteen meter city bus equipped with a CI engine with a displacement of 9.2 dm3. The latest PEMS mobile equipment technology was used to conduct the road measurements. This allowed the emission indicators for CO, HC, NOx and PM to be determined, including specific emissions. The obtained values were then compared with the Euro V limits.The analysis of the test results was supplemented with the calculation of fuel consumption using the carbonbalance method.

  9. Study on emission characteristics of hybrid bus under driving cycles in typical Chinese city

    Science.gov (United States)

    Xie, Yongdong; Xu, Guangju

    2017-09-01

    In this study, hybrid city bus was taken as the research object, through the vehicle drum test, the vehicle emissions of hybrid bus, the transient emissions of gas pollutants, as well as the particle size and number distribution were surveyed. The results of the studies are listed as follows: First, compared to traditional fuel bus, hybrid bus could reduce about 44% of the NOx emissions, 33% of the total hydrocarbon emissions, and 51% of the particles emissions. Furthermore, the distribution of particles number concentration of test vehicle became high in middle and low in both sides. More specifically, the particle number concentration was mainly concentrated in the range from 0.021 to 0.755μm, the maximum was 0.2μm, and particle size of particulate matter (PM) less than 1.2μm accounted for 95% of the total number concentration. Particulate mass concentration was increased with increment of particle size, and the maximum of particulate mass (PM) concentration was 6.2μm. On average, whether traditional fuel bus or hybrid bus, the particle size of particulate matter(PM) less than 2.5μm accounted for more than 98% in the particles emission. It is found that the particles are more likely to deposit to the lung, respiratory bronchioles and alveoli, causing respiratory and lung diseases. Therefore, how to control the PM emissions of hybrid bus is the key factor of the study.

  10. COMPARISON OF PARALLEL AND SERIES HYBRID POWERTRAINS FOR TRANSIT BUS APPLICATION

    Energy Technology Data Exchange (ETDEWEB)

    Gao, Zhiming [ORNL; Daw, C Stuart [ORNL; Smith, David E [ORNL; Jones, Perry T [ORNL; LaClair, Tim J [ORNL; Parks, II, James E [ORNL

    2016-01-01

    The fuel economy and emissions of both conventional and hybrid buses equipped with emissions aftertreatment were evaluated via computational simulation for six representative city bus drive cycles. Both series and parallel configurations for the hybrid case were studied. The simulation results indicate that series hybrid buses have the greatest overall advantage in fuel economy. The series and parallel hybrid buses were predicted to produce similar CO and HC tailpipe emissions but were also predicted to have reduced NOx tailpipe emissions compared to the conventional bus in higher speed cycles. For the New York bus cycle (NYBC), which has the lowest average speed among the cycles evaluated, the series bus tailpipe emissions were somewhat higher than they were for the conventional bus, while the parallel hybrid bus had significantly lower tailpipe emissions. All three bus powertrains were found to require periodic active DPF regeneration to maintain PM control. Plug-in operation of series hybrid buses appears to offer significant fuel economy benefits and is easily employed due to the relatively large battery capacity that is typical of the series hybrid configuration.

  11. Performance Analysis of Trans-Jakarta Bus Suburban Service Move-Across Greater Jakarta

    Science.gov (United States)

    Tangkudung, ESW; Widyadayinta, C.

    2018-03-01

    Trans-Jakarta have developed their services scope as Suburban Service or Feeder move-across service that operate from greater Jakarta into Jakarta central vice versa. One of the route is Ciputat – Bundaran Hotel Indonesia (Tosari) and integrated with corridor 1 (one) and 8 (eight). This service is not travel on the exclusive lane or bus-way. Objective of Government Jakarta to provide this service is to decrease private car to enter the central of Jakarta. The objective of this study is to find the performance of the service. Survey have conducted static and dynamic on work day to get variable of travel time and delay, waiting time of passenger at the bus stop, headway and ridership of the bus. Service Standard Minimum of Trans-Jakarta have compared with the result of variable headway, travel speed, and waiting time at bus stop as concern of all the passengers. Analysis use correlation test method and linear regression model have done. The performance of Trans-Jakarta bus suburban service, based on travel speed indicator is fairly bad, only 8.1% of trip could comply with Minimum Service Standard. Bus performance based on the indicator of density in the bus is good, where all points are below the maximum limit i.e. 8 people/m2 at peak hour and 5 people/m2 at off-peak hour.

  12. Analisis Penentuan Tarif Layanan Bus Kota Berdasarkan Marginal Cost Pricing (Studi Pada Perum Damri Kota Surabaya

    Directory of Open Access Journals (Sweden)

    Dewi Prastiwi

    2013-10-01

    Full Text Available The concept of regional autonomy has implications for financing in all sectors, including transport. To be able to provide adequate public transport facilities, one of the opportunities is the mobilization of funds through tariff collection mechanism. Determination of transport rates set out in the local rules based approach Incrementalism and line items. This approach represents a lack of economic and psychological capabilities and suitability of the benefits received by the sacrifices that have been issued. Therefore research is needed to analyze the determination of rates of local regulations bound public services locally. This study aimed to analyze the determination of the city bus rate by Cost Pricing (MCP marginal approach, that was the determination of tariff by considering the social benefits received by customers, so if there were additional rates so consumers should receive additional social benefits. Based MCP, Perum Damri can assign the same rate if the consumer gets the same standard of service, but if there was a decline in the standard of service, then the rates should be differentiated.

  13. Methodology for the analysis of pollutant emissions from a city bus

    International Nuclear Information System (INIS)

    Armas, Octavio; Lapuerta, Magín; Mata, Carmen

    2012-01-01

    In this work a methodology is proposed for measurement and analysis of gaseous emissions and particle size distributions emitted by a diesel city bus during its typical operation under urban driving conditions. As test circuit, a passenger transportation line at a Spanish city was used. Different ways for data processing and representation were studied and, derived from this work, a new approach is proposed. The methodology was useful to detect the most important uncertainties arising during registration and processing of data derived from a measurement campaign devoted to determine the main pollutant emissions. A HORIBA OBS-1300 gas analyzer and a TSI engine exhaust particle spectrometer were used with 1 Hz frequency data recording. The methodology proposed allows for the comparison of results (in mean values) derived from the analysis of either complete cycles or specific categories (or sequences). The analysis by categories is demonstrated to be a robust and helpful tool to isolate the effect of the main vehicle parameters (relative fuel–air ratio and velocity) on pollutant emissions. It was shown that acceleration sequences have the highest contribution to the total emissions, whereas deceleration sequences have the least. (paper)

  14. Methodology for the analysis of pollutant emissions from a city bus

    Science.gov (United States)

    Armas, Octavio; Lapuerta, Magín; Mata, Carmen

    2012-04-01

    In this work a methodology is proposed for measurement and analysis of gaseous emissions and particle size distributions emitted by a diesel city bus during its typical operation under urban driving conditions. As test circuit, a passenger transportation line at a Spanish city was used. Different ways for data processing and representation were studied and, derived from this work, a new approach is proposed. The methodology was useful to detect the most important uncertainties arising during registration and processing of data derived from a measurement campaign devoted to determine the main pollutant emissions. A HORIBA OBS-1300 gas analyzer and a TSI engine exhaust particle spectrometer were used with 1 Hz frequency data recording. The methodology proposed allows for the comparison of results (in mean values) derived from the analysis of either complete cycles or specific categories (or sequences). The analysis by categories is demonstrated to be a robust and helpful tool to isolate the effect of the main vehicle parameters (relative fuel-air ratio and velocity) on pollutant emissions. It was shown that acceleration sequences have the highest contribution to the total emissions, whereas deceleration sequences have the least.

  15. Cloud computing-based energy optimization control framework for plug-in hybrid electric bus

    International Nuclear Information System (INIS)

    Yang, Chao; Li, Liang; You, Sixiong; Yan, Bingjie; Du, Xian

    2017-01-01

    Considering the complicated characteristics of traffic flow in city bus route and the nonlinear vehicle dynamics, optimal energy management integrated with clustering and recognition of driving conditions in plug-in hybrid electric bus is still a challenging problem. Motivated by this issue, this paper presents an innovative energy optimization control framework based on the cloud computing for plug-in hybrid electric bus. This framework, which includes offline part and online part, can realize the driving conditions clustering in offline part, and the energy management in online part. In offline part, utilizing the operating data transferred from a bus to the remote monitoring center, K-means algorithm is adopted to cluster the driving conditions, and then Markov probability transfer matrixes are generated to predict the possible operating demand of the bus driver. Next in online part, the current driving condition is real-time identified by a well-trained support vector machine, and Markov chains-based driving behaviors are accordingly selected. With the stochastic inputs, stochastic receding horizon control method is adopted to obtain the optimized energy management of hybrid powertrain. Simulations and hardware-in-loop test are carried out with the real-world city bus route, and the results show that the presented strategy could greatly improve the vehicle fuel economy, and as the traffic flow data feedback increases, the fuel consumption of every plug-in hybrid electric bus running in a specific bus route tends to be a stable minimum. - Highlights: • Cloud computing-based energy optimization control framework is proposed. • Driving cycles are clustered into 6 types by K-means algorithm. • Support vector machine is employed to realize the online recognition of driving condition. • Stochastic receding horizon control-based energy management strategy is designed for plug-in hybrid electric bus. • The proposed framework is verified by simulation and hard

  16. Optimization of transit bus fleet's life cycle assessment impacts with alternative fuel options

    International Nuclear Information System (INIS)

    Ercan, Tolga; Zhao, Yang; Tatari, Omer; Pazour, Jennifer A.

    2015-01-01

    Public transportation is one of the most promising transportation modes to reduce the environmental emissions of the transportation sector in the U.S. In order to mitigate the environmental impacts brought by the transit bus system, new energy buses are introduced into the vehicle market. The goal of this study is to find an optimal bus fleet combination for different driving conditions to minimize life cycle cost, greenhouse gas emissions, and conventional air pollutant emission impacts. For this purpose, a Multi-Objective Linear Programming approach is used to select the optimum bus fleet combinations. Given different weight scenarios, this method could effectively provide solutions for decision makers with various budget constraints or emission reduction requirements. The results indicate that in heavily congested driving cycles such as the Manhattan area, the battery electric bus is the dominant vehicle type, while the hybrid bus has more balanced performances in most scenarios because of its lower initial investment comparing to battery electric buses. Petroleum powered buses have seldom been selected by the model. The trade-off analysis shows that the overall greenhouse gas impact performance is sensitive to the life cycle cost after certain points, which could provide valuable information for the bus fleet combination planning. - Highlights: • Hybrid-Life Cycle Assessment analysis approach for transit bus operations. • Optimizing the economic and sustainability impacts of transit bus fleet operation. • CO 2 emissions and other air pollutants related health and environmental damage cost. • Trade-offs between CO 2 emissions and cost of transit bus fleet operation.

  17. Connecticut Transit (CTTRANSIT) Fuel Cell Transit Bus: Third Evaluation Report and Appendices

    Energy Technology Data Exchange (ETDEWEB)

    Chandler, K.; Eudy, L.

    2010-01-01

    This report describes operations at Connecticut Transit (CTTRANSIT) in Hartford for one prototype fuel cell bus and three new diesel buses operating from the same location. The prototype fuel cell bus was manufactured by Van Hool and ISE Corp. and features an electric hybrid drive system with a UTC Power PureMotion 120 Fuel Cell Power System and ZEBRA batteries for energy storage. The fuel cell bus started operation in April 2007, and evaluation results through October 2009 are provided in this report.

  18. Characterizing the range of children's air pollutant exposure during school bus commutes.

    Science.gov (United States)

    Sabin, Lisa D; Behrentz, Eduardo; Winer, Arthur M; Jeong, Seong; Fitz, Dennis R; Pankratz, David V; Colome, Steven D; Fruin, Scott A

    2005-09-01

    Real-time and integrated measurements of gaseous and particulate pollutants were conducted inside five conventional diesel school buses, a diesel bus with a particulate trap, and a bus powered by compressed natural gas (CNG) to determine the range of children's exposures during school bus commutes and conditions leading to high exposures. Measurements were made during 24 morning and afternoon commutes on two Los Angeles Unified School District bus routes from South to West Los Angeles, with seven additional runs on a rural/suburban route, and three runs to test the effect of window position. For these commutes, the mean concentrations of diesel vehicle-related pollutants ranged from 0.9 to 19 microg/m(3) for black carbon, 23 to 400 ng/m(3) for particle-bound polycyclic aromatic hydrocarbon (PB-PAH), and 64 to 220 microg/m(3) for NO(2). Concentrations of benzene and formaldehyde ranged from 0.1 to 11 microg/m(3) and 0.3 to 5 microg/m(3), respectively. The highest real-time concentrations of black carbon, PB-PAH and NO(2) inside the buses were 52 microg/m(3), 2000 ng/m(3), and 370 microg/m(3), respectively. These pollutants were significantly higher inside conventional diesel buses compared to the CNG bus, although formaldehyde concentrations were higher inside the CNG bus. Mean black carbon, PB-PAH, benzene and formaldehyde concentrations were higher when the windows were closed, compared with partially open, in part, due to intrusion of the bus's own exhaust into the bus cabin, as demonstrated through the use of a tracer gas added to each bus's exhaust. These same pollutants tended to be higher on urban routes compared to the rural/suburban route, and substantially higher inside the bus cabins compared to ambient measurements. Mean concentrations of pollutants with substantial secondary formation, such as PM(2.5), showed smaller differences between open and closed window conditions and between bus routes. Type of bus, traffic congestion levels, and encounters with

  19. On the road : non-fossil fuel deployment for the public bus fleet of Sweden

    OpenAIRE

    Xylia, Maria; Silveira, Semida

    2015-01-01

    The public transport sector in Sweden has set a target to run 90% of its total vehicle-kilometers on renewable fuels by 2020, and double its market share in the long term. The focus of this paper is the adoption of renewable fuels in public bus fleets. Data for all 21 Swedish counties were gathered and analyzed, mapping the bus fleets’ condition in relation to renewable fuel deployment, CO2 emissions and energy efficiency. The main factors affecting fuel choices in the bus fleets were investi...

  20. Level of Bus Performance Based On the Relationship Between Distance and Travel Time of Universiti Tun Hussein Onn Malaysia (UTHM Bus Services

    Directory of Open Access Journals (Sweden)

    Prasetijo Joewono

    2017-01-01

    Full Text Available UTHM bus service is an important transport mode for most students at Universiti Tun Hussein Onn because it such primary public vehicle to support students movements around the campus, within and outside student apartments. This service is often associated with the quality of service in terms of time, stops and comforts. Therefore, this following study is focused on investigation on several UTHM bas routes which was based on bas operations such as distance and travel time/travel distance that would determine the level of service provided. Primary data were collected mainly to obtain information relate to speed, bas position, time movement/circulations of bus and time headway. These were obtained by installing GPS-Slute Gear i-trail along bus travels. In addition, additional data were collected by exploring previous studies regarding to the bus services such as Highway Capacity Manual (HCM 2010. The approach used was based on assessment of progress used to determine the level of quest service and such obstacle frequently occurs with results on bus delays, volume of unequal that can be overcome according to the assessments that have been provided.

  1. A Rule-Based Energy Management Strategy for a Plug-in Hybrid School Bus Based on a Controller Area Network Bus

    Directory of Open Access Journals (Sweden)

    Jiankun Peng

    2015-06-01

    Full Text Available This paper presents a rule-based energy management strategy for a plug-in hybrid school bus (PHSB. In order to verify the effectiveness and rationality of the proposed energy management strategy, the powertrain and control models were built with MATLAB/Simulink. The PHSB powertrain model includes an engine model, ISG (integrated started and generator model, drive motor model, power battery packs model, driver model, and vehicle longitudinal dynamics model. To evaluate the controller area network (CAN bus performance features such as the bus load, signal hysteresis, and to verify the reliability and real-time performance of the CAN bus multi-node control method, a co-simulation platform was built with CANoe and MATLAB/Simulink. The co-simulation results show that the control strategy can meet the requirements of the PHSB’s dynamic performance. Meanwhile, the charge-depleting mode (CD and charge-sustaining mode (CS can switch between each other and maintain a state-of-charge (SoC of around 30%, indicating that the energy management strategy effectively extends the working period of the CD mode and improves the fuel economy further. The energy consumption per 100 km includes 13.7 L diesel and 10.5 kW·h electricity with an initial SoC of 75%. The CANoe simulation results show that the bus communication performs well without error frames.

  2. Bus Rapid Transit system’s influence on urban development: An inquiry to Boston and Seoul BRT systems’ technical characteristics

    Science.gov (United States)

    Prayogi, Lutfi

    2018-03-01

    This article explores the relation between bus rapid transit (BRT) system and urban development. This article was written through a multi-staged comprehensive literature review. It includes a general overview of widely acknowledged BRT technical characteristics. It explains the approach taken in understanding the relation between BRT system provision and urban development around the system. Findings regarding the influence of Boston Silver Line 4 and 5 and Seoul BRT systems on urban development around the systems are quoted and used as case studies. Investigation on the technical characteristics of Boston SL4/5 and Seoul BRT systems are provided. This article shows that the two BRT systems that influence urban development around the systems have technical characteristics that enable the BRT systems to have high performance. However, while the quoted BRT systems can influence urban development, they have significantly different performance.

  3. Risk factors associated with bus accident severity in the United States: A generalized ordered logit model

    DEFF Research Database (Denmark)

    Kaplan, Sigal; Prato, Carlo Giacomo

    2012-01-01

    of 2011. Method: The current study investigates the underlying risk factors of bus accident severity in the United States by estimating a generalized ordered logit model. Data for the analysis are retrieved from the General Estimates System (GES) database for the years 2005–2009. Results: Results show...... that accident severity increases: (i) for young bus drivers under the age of 25; (ii) for drivers beyond the age of 55, and most prominently for drivers over 65 years old; (iii) for female drivers; (iv) for very high (over 65 mph) and very low (under 20 mph) speed limits; (v) at intersections; (vi) because......Introduction: Recent years have witnessed a growing interest in improving bus safety operations worldwide. While in the United States buses are considered relatively safe, the number of bus accidents is far from being negligible, triggering the introduction of the Motor-coach Enhanced Safety Act...

  4. Analysis of Journey to Work Travel Behavior by Car and Bus in the Sydney Metropolitan Region

    Directory of Open Access Journals (Sweden)

    Suthanaya P.A.

    2011-01-01

    Full Text Available Car dependence is a fundamental problem in the sustainability of cities with low-density suburban sprawl. Increasing the use of public transport is one of the policy objectives commonly adopted to overcome this problem. It is essential to study journey to work travel behavior by car and bus. This paper applied preference function to analyze travel behavior and Moran’s I spatial statistic to evaluate the spatial association. The results indicated that the commuting preferences of residents have moved towards distance maximization. In general, bus was preferred for shorter distance trips whilst car was preferred for longer distance trips. Unlike car, by increasing distances from the Central Business District, residents tended to use bus for shorter distance trip. A significant positive spatial association was identified for both the slope preferences by car and bus where zones with a preference towards longer or shorter trips tended to travel to zones with similar preferences.

  5. Exploring public bus service quality in South Africa: A structural equation modelling approach

    Directory of Open Access Journals (Sweden)

    Ayanda M. Vilakazi

    2014-07-01

    Full Text Available This study, which is a deviation from the usual practice of using SERVQUAL or an adaptedversion thereof, uses McKnight, Pagano and Paaswell’s (1986 service quality dimensions,namely reliability; extent of service; comfort; safety; and affordability (RECSA and structuralequation modelling to determine commuters’ perception of public bus service quality in amajor city in South Africa. The RECSA model was adapted and fitted to the data collectedfrom a convenience sample of bus commuters in Johannesburg, using structural equationmodelling. It was ascertained that reliability, service, comfort and safety influenced thepublic bus commuters’ perception of the overall service quality. The implications of theaforementioned findings for providers of public bus services are explained.

  6. City of Fresno peer exchange on bus rapid transit : a TPCB peer exchange

    Science.gov (United States)

    2013-09-11

    This report highlights key recommendations and best practices identified at the peer exchange on Bus Rapid Transit (BRT), held on May 21 and May 22, 2013, in Fresno, California. This event was sponsored by the Transportation Planning Capacity Buildin...

  7. Outsourcing of Defense Supply Center, Columbus, Bus and Taxi Service Operations

    National Research Council Canada - National Science Library

    Granetto, Paul

    1999-01-01

    Introduction. We performed the audit in response to allegations to the Defense Hotline that the Defense Supply Center, Columbus, outsourcing study for bus and taxi service operations was based on incorrect methodology...

  8. State and Federal project development procedures for bus rapid transit : managing differences and reducing implementation delays

    Science.gov (United States)

    2011-08-01

    This report documents an investigation into the transportation project development process in the : context of the implementation of bus rapid transit systems on the State Highway System as well as such : systems being part of the Federal New Starts ...

  9. NREL Showcases Hydrogen Internal Combustion Engine Bus, Helps DOE Set Standards for Outreach (Fact Sheet)

    Energy Technology Data Exchange (ETDEWEB)

    2010-11-01

    This fact sheet describes the National Renewable Energy Laboratory's (NREL's) accomplishments in showcasing a Ford hydrogen-powered internal combustion engine (H2ICE) bus at The Taste of Colorado festival in Denver. NREL started using its U.S. Department of Energy-funded H2ICE bus in May 2010 as the primary shuttle vehicle for VIP visitors, members of the media, and new employees. In September 2010, NREL featured the bus at The Taste of Colorado. This was the first major outreach event for the bus. NREL's educational brochure, vehicle wrap designs, and outreach efforts serve as a model for other organizations with DOE-funded H2ICE buses. Work was performed by the Hydrogen Education Group and Market Transformation Group in the Hydrogen Technologies and Systems Center.

  10. State of bus safety in the U.S. : summary of federal and state regulations.

    Science.gov (United States)

    2014-06-01

    This report provides a comprehensive overview of transit bus safety regulations and standards developed by all 50 states, as well as : information on how state departments of transportation (DOT) regulate the maintenance or operation of transit/parat...

  11. Modeling and Simulation of Bus Dispatching Policy for Timed Transfers on Signalized Networks

    Science.gov (United States)

    Cho, Hsun-Jung; Lin, Guey-Shii

    2007-12-01

    The major work of this study is to formulate the system cost functions and to integrate the bus dispatching policy with signal control. The integrated model mainly includes the flow dispersion model for links, signal control model for nodes, and dispatching control model for transfer terminals. All such models are inter-related for transfer operations in one-center transit network. The integrated model that combines dispatching policies with flexible signal control modes can be applied to assess the effectiveness of transfer operations. It is found that, if bus arrival information is reliable, an early dispatching decision made at the mean bus arrival times is preferable. The costs for coordinated operations with slack times are relatively low at the optimal common headway when applying adaptive route control. Based on such findings, a threshold function of bus headway for justifying an adaptive signal route control under various time values of auto drivers is developed.

  12. 75 FR 2583 - Over-the-Road Bus Accessibility Program Grants

    Science.gov (United States)

    2010-01-15

    ... complying with DOT's over- the-road bus accessibility regulation. The authorizing legislation calls for..., 915 Chicago, IL 60606, Tel. 312-353- Second Avenue, Suite 3142, 2789. Seattle, WA 98174-1002, Tel. 206...

  13. Annoyance evaluation and the effect of noise on the health of bus drivers

    Directory of Open Access Journals (Sweden)

    Portela S Bruno

    2013-01-01

    Full Text Available In the present study, we evaluated annoyance and the effects of noise on the health of bus drivers. For that, 200 bus drivers from a public transport company participated in a cross-sectional study. Annoyance and effects on health was measured with analog scale: Sleep quality, occurrence of tinnitus, headache, irritation, and annoyance from bus engine, traffic, and passengers. Data of age and working time of bus drivers also were obtained. For noise exposure, LA eq was evaluated in 80 buses. Statistical analysis consisted of mean, standard deviation, minimum, and maximum, Kruskal-Wallis test with post-hoc Dunn, one-way ANOVA with post-hoc Tukey and Spearman′s correlation coefficient. Results indicate three groups of bus drivers (not annoyed: (N.A., a little annoyed (L.A. and highly annoyed (H.A.. The group H.A. was younger and with less working time in relation to others, with a significant difference only for age. Regarding sleep quality, there was no significant difference. For results on the occurrence of tinnitus, headache and irritation after work, group H.A. had significantly higher means. Result of annoyance to the bus engine was significantly higher in H.A. than in L.A. and N.A. Annoyance to traffic and passengers, no significant differences were found, but the highest results were found for L.A., followed by H.A. and N.A. Equivalent sound pressure level in buses was above of the limit for occupational comfort. It was concluded that bus drivers has considerable level of noise annoyance and some health effects are perceived. The noise is a factor discomfort ergonomic that may cause effects on health of bus drivers. This study aims to evaluate annoyance and the effects of noise on the health of bus drivers. Cross-sectional study with buses and bus drivers. For that, 200 bus drivers from a public transport company participated in a cross-sectional study. Annoyance and effects on health was measured with analog scale: Sleep quality

  14. Individual and population intake fractions of diesel particulate matter (DPM) in bus stop microenvironments

    International Nuclear Information System (INIS)

    Xu, Jia; Jin, Taosheng; Miao, Yaning; Han, Bin; Gao, Jiajia; Bai, Zhipeng; Xu, Xiaohong

    2015-01-01

    Diesel particulate matter (DPM) is associated with adverse human health effects. This study aims to investigate the relationship between DPM exposure and emissions by estimating the individual intake fraction (iF_i) and population intake fraction (iF_p) of DPM. Daily average concentrations of particulate matter at two bus stops during rush hours were measured, and then they were apportioned to DPM due to heavy-duty diesel bus emissions using Chemical Mass Balance Model. The DPM emissions of diesel buses for different driving conditions (idling, creeping and traveling) were estimated on the basis of field observations and published emission factors. The median iF_i of DPM was 0.67 and 1.39 per million for commuters standing at the bus stop and pedestrians/cyclists passing through the bus stop during rush hours, respectively. The median iF_p of DPM was 94 per million. Estimations of iF_i and iF_p of DPM are potentially significant for exposure assessment and risk management. - Highlights: • Methods to estimate the individual and population intake fraction in bus stop microenvironments were established. • Source apportionment was performed to estimate the DPM due to diesel bus emissions in bus stop microenvironments. • The DPM emission in bus stop microenvironments rather than in the entire urban area was considered. • The movement of people and their exposure duration were introduced in the estimation of population intake fraction. - This work established a method to estimate the individual and population intake fraction in transportation microenvironments on the basis of PM source apportionment.

  15. Bavarian liquid hydrogen bus demonstration project - safety, licensing and acceptability aspects

    Energy Technology Data Exchange (ETDEWEB)

    Wurster, R.; Knorr, H.; Pruemm, W.

    1999-07-01

    A regular 12 m city bus of the MAN SL 202 type with an internal combustion engine adapted to hydrogen operation and auxiliary gasoline operation was demonstrated in the Bavarian cities of Erlangen and Munich between April 1996 and August 1998. Three bus operators, Erlanger Stadtwerke, Stadtwerke Muenchen and Autobus Oberbayern were testing the bus in three different operating schemes. In order to be able to perform this worldwide first public demonstration of a liquid hydrogen (LH{sub 2}) city bus in regular service, several requirements with respect to safety, licensing, training and acceptability had to be fulfilled. These activities were focusing mainly on the hydrogen specific issues such as (a) integration of onboard LH{sub 2} storage vessels, piping and instrumentation, (b) implementation of storage and refueling infrastructure in the operators' yards, (c) adaptation of the maintenance garages, (d) training of operating and maintenance personnel. During phase II of the demonstration activity a poll was performed on passengers traveling onboard the hydrogen-powered city bus in order to determined the level of acceptance among the users of the bus. The bus was designed and manufactured by MAN Nutzfahrzeuge Aktiengesellschaft. The cryogenic fuel storage and the refueling equipment were designed and manufactured by Linde AG. The realization of the hardware was financially supported by the European Commission (EC) within the Euro-Quebec Hydro-Hydrogen Pilot Project. The demonstration phase was financially supported by EC and the Bavarian State Government. Ludwig-Boelkow-Systemtechnik performed project monitoring for both funding organizations. The presentation will summarize the most important results of this demonstration phase and will address the measures undertaken in order to get the bus, the refueling infrastructure and the maintenance and operating procedures approved by the relevant authorities.

  16. The impact of bus drivers ’ lifestyle on the occurrence of health problems and absenteeism

    Directory of Open Access Journals (Sweden)

    Andrej Jerman

    2016-06-01

    Full Text Available Research Question: Do bus drivers’ lifestyles affect the occurrence of health problems and absenteeism? Purpose: The purpose of the study was to determine whether the lifestyle of professional bus drivers affects the occurrence of health problems and the phenomenon of absenteeism. Method: A quantitative research method was used in the research. Data were collected using a structured questionnaire, on a sample of 230 professional bus drivers from different bus transport companies in Slovenia. Selected data were analyzed with chi-square test and multiple regression analysis. Results: We determined that there is a relationship between the state of health of professional bus drivers and participation in sport activity and that there is a statistically significant impact of lifestyle on the absenteeism of professional bus drivers. Organization: The study points to the necessity of management’s awareness to improve the conditions for the health status of employees and, consequently, absenteeism. Managers need to be more vigilant in ensuring conditions and social security that will allow employees a higher quality lifestyle. Society: The poor quality lifestyle of professional bus drivers, which includes different addictions, inadequate physical activity, and poor working conditions, is a significant factor causing absenteeism. All these factors influence the onset of negative consequences, such as the direct cost of compensation payments, costs of replacing the absent person, a reduction in productivity, which in turn affect economic growth and the high cost of health care. Originality: This is the first focus group study of professional bus drivers that targets lifestyle and its connection to absenteeism. Limitations/Future Research: The main limitation of the study is the number of respondents. The reason for this is that professional drivers are less responsive in the survey and that the study was conducted only in Slovenia, country of two

  17. Telemetry Standards, RCC Standard 106-17. Chapter 8. Digital Data Bus Acquisition Formatting Standard

    Science.gov (United States)

    2017-07-01

    incorrect word count/message and illegal mode codes are not considered bus errors. 8.6.2 Source Signal The source of data is a signal conforming to...Telemetry Standards, RCC Standard 106-17 Chapter 8, July 2017 CHAPTER 8 Digital Data Bus Acquisition Formatting Standard Acronyms...check FCS frame check sequence HDDR high-density digital recording MIL-STD Military Standard msb most significant bit PCM pulse code modulation

  18. Shelter from the Storm: Optimizing Distribution of Bus Stop Shelters in Los Angeles

    OpenAIRE

    Law, Philip; Taylor, Brian D.

    2010-01-01

    The functions of bus stop shelters and factors affecting their placement at stops in transit systems are analyzed. Drawing on information from a variety of sources, current shelter placement policy in Los Angeles was found to be guided principally by the revenue-generating potential of shelter advertisements, secondarily by political concerns over geographic equity, and only peripherally on the basis of bus stop use. Using data on shelter and stop locations, boardings, and headways, a methodo...

  19. Driving Behavior Analysis through CAN Bus Data in an Uncontrolled Environment

    OpenAIRE

    Fugiglando, Umberto; Massaro, Emanuele; Santi, Paolo; Milardo, Sebastiano; Abida, Kacem; Stahlmann, Rainer; Netter, Florian; Ratti, Carlo

    2017-01-01

    Cars can nowadays record several thousands of signals through the CAN bus technology and potentially provide real-time information on the car, the driver and the surrounding environment. This paper proposes a new method for the analysis and classification of driver behavior using a selected subset of CAN bus signals, specifically gas pedal position, brake pedal pressure, steering wheel angle, steering wheel momentum, velocity, RPM, frontal and lateral acceleration. Data has been collected in ...

  20. Design of Bus Protocol Intelligent Initiation System Based On RS485

    Directory of Open Access Journals (Sweden)

    Li Liming

    2017-01-01

    Full Text Available In order to design an effective and reliable RS485 bus protocol based on RS485 bus, this paper introduces the structure and transmission mode of the command frame and the response frame, and also introduce four control measures and the communication in order to process quality of this system. The communication protocol is open, tolerant, reliable and fast, and can realize ignition more reliable and accurate in the intelligent initiation system.

  1. Exploring public bus service quality in South Africa: A structural equation modelling approach

    OpenAIRE

    Ayanda M. Vilakazi; Krishna K. Govender

    2014-01-01

    This study, which is a deviation from the usual practice of using SERVQUAL or an adaptedversion thereof, uses McKnight, Pagano and Paaswell’s (1986) service quality dimensions,namely reliability; extent of service; comfort; safety; and affordability (RECSA) and structuralequation modelling to determine commuters’ perception of public bus service quality in amajor city in South Africa. The RECSA model was adapted and fitted to the data collectedfrom a convenience sample of bus commuters in Joh...

  2. Thermal and mechanical properties of palm oil-based polyurethane acrylate/clay nanocomposites prepared by in-situ intercalative method and electron beam radiation

    International Nuclear Information System (INIS)

    Salih, A. M.; Ahmad, Mansor Bin; Ibrahim, Nor Azowa; Dahlan, Khairul Zaman Hj Mohd; Tajau, Rida; Mahmood, Mohd Hilmi; Yunus, Wan Md. Zin Wan

    2014-01-01

    Palm oil based-polyurethane acrylate (POBUA)/clay nanocomposites were prepared via in-situ intercalative polymerization using epoxidized palm oil acrylate (EPOLA) and 4,4' methylene diphenyl diisocyante (MDI). Organically modified Montmorillonite (ODA-MMT) was incorporated in EPOLA (1, 3 and 5%wt), and then subjected to polycondensation reaction with MDI. Nanocomposites solid films were obtained successfully by electron beam radiation induced free radical polymerization (curing). FTIR results reveal that the prepolymer was obtained successfully, with nanoclay dispersed in the matrix. The intercalation of the clay in the polymer matrix was investigated by XRD and the interlayer spacing of clay was found to be increased up to 37 Å, while the structure morphology of the nanocomposites was investigated by TEM and SEM. The nanocomposites were found to be a mixture of exfoliated and intercalated morphologies. The thermal stability of the nanocomposites was significantly increased by incorporation of nanoclay into the polymer matrix. DSC results reveal that the Tg was shifted to higher values, gradually with increasing the amount of filler in the nanocomposites. Tensile strength and Young's modulus of the nanocomposites showed remarkable improvement compared to the neat POBUA

  3. Thermal and mechanical properties of palm oil-based polyurethane acrylate/clay nanocomposites prepared by in-situ intercalative method and electron beam radiation

    Energy Technology Data Exchange (ETDEWEB)

    Salih, A. M. [Department of Chemistry, Faculty of Science, University Putra Malaysia 43400, UPM, Serdang, Selangor, Malaysia and Department of Radiation Processing, Sudan Atomic Energy Commission, Khartoum 1111 (Sudan); Ahmad, Mansor Bin; Ibrahim, Nor Azowa [Department of Chemistry, Faculty of Science, University Putra Malaysia 43400, UPM, Serdang, Selangor (Malaysia); Dahlan, Khairul Zaman Hj Mohd [Polycomposite Sdn Bhd, No.75-2, Jalan TKS 1, Taman Kajang Sentral, 43000 Kajang, Selangor (Malaysia); Tajau, Rida [Radiation Processing Technology Division, Nuclear Malaysia, Bangi, 43000 Kajang, Selangor (Malaysia); Mahmood, Mohd Hilmi [No. 107, Jalan 2, Taman Kajang Baru, Sg Jelok, 43000 Kajang, Selangor (Malaysia); Yunus, Wan Md. Zin Wan [Department of Chemistry, Centre for Defence Foundation Studies, National Defence University of Malaysia, 57000, Sungai Besi Camp, Kuala Lumpur (Malaysia)

    2014-02-12

    Palm oil based-polyurethane acrylate (POBUA)/clay nanocomposites were prepared via in-situ intercalative polymerization using epoxidized palm oil acrylate (EPOLA) and 4,4' methylene diphenyl diisocyante (MDI). Organically modified Montmorillonite (ODA-MMT) was incorporated in EPOLA (1, 3 and 5%wt), and then subjected to polycondensation reaction with MDI. Nanocomposites solid films were obtained successfully by electron beam radiation induced free radical polymerization (curing). FTIR results reveal that the prepolymer was obtained successfully, with nanoclay dispersed in the matrix. The intercalation of the clay in the polymer matrix was investigated by XRD and the interlayer spacing of clay was found to be increased up to 37 Å, while the structure morphology of the nanocomposites was investigated by TEM and SEM. The nanocomposites were found to be a mixture of exfoliated and intercalated morphologies. The thermal stability of the nanocomposites was significantly increased by incorporation of nanoclay into the polymer matrix. DSC results reveal that the Tg was shifted to higher values, gradually with increasing the amount of filler in the nanocomposites. Tensile strength and Young's modulus of the nanocomposites showed remarkable improvement compared to the neat POBUA.

  4. Thermal and mechanical properties of palm oil-based polyurethane acrylate/ clay nano composites prepared by in-situ intercalative method and electron beam radiation

    International Nuclear Information System (INIS)

    Salih, A.M.; Mansor Ahmad; Nor Azowa Ibrahim; Rida Tajau; Wan Mohd Zin Wan Yunus

    2013-01-01

    Full-text: Palm oil based-polyurethane acrylate (POBUA)/ clay nano composites were prepared via in-situ intercalative polymerization using epoxidized palm oil acrylate (EPOLA) and 4,4 ' methylene diphenyl diisocyante (MDI). Organically modified Montmorillonite (ODA-MMT) was incorporated in EPOLA (1, 3 and 5 % wt), and then subjected to polycondensation reaction with MDI. Nano composites solid films were obtained successfully by electron beam radiation induced free radical polymerization (curing). FTIR results reveal that the prepolymer was obtained successfully, with nano clay dispersed in the matrix. The intercalation of the clay in the polymer matrix was investigated by XRD and the interlayer spacing of clay was found to be increased up to 37 Angstrom, while the structure morphology of the nano composites was investigated by TEM and SEM. The nano composites were found to be a mixture of exfoliated and intercalated morphologies. The thermal stability of the nano composites was significantly increased by incorporation of nano clay into the polymer matrix. DSC results reveal that the T g was shifted to higher values, gradually with increasing the amount of filler in the nano composites. Tensile strength and Young's modulus of the nano composites showed remarkable improvement compared to the neat POBUA. (author)

  5. [Injuries sustained by bus passengers in the municipality of Odense 1996-1999].

    Science.gov (United States)

    Barsi, T; Faergemann, C; Larsen, L B

    2001-10-22

    Owing to several recent bus-related accidents in Denmark, we wished to investigate injuries sustained by passengers. From our ongoing registration of patients treated in the casualty department at Odense University Hospital, we identified all residents of Odense Municipality who had sustained injuries as bus passengers from 1996 to 1999. Market analysis and demographic information were used to calculate the incidence and risk. Over this four-year period, 327 consecutive injuries had been sustained by 246 bus passengers, 72 men and 174 women, mean ages 44 and 53 years. The incidence rate was 3.3 injured per 10,000 inhabitants per year, with no increasing tendency during the study period. The risk was 2.2 injured per 1,000,000 bus passengers per year, highest in women and increasing with age. Injuries most frequently occurred when the bus stopped (31%), as passengers were boarding or alighting (23%), or during collision with another vehicle (20%). Most commonly injured areas were the lower (30%) and upper (28%) extremities and the head or neck (27%). Contusions and sprains were the most common injuries (59%). The most common fractures were those of the humerus and hip region. Bus passenger injuries are not a growing problem. The incidence increases with age.

  6. Evaluating the Impacts of Bus Fare on Social Equity Based on IC Card Data in China

    Directory of Open Access Journals (Sweden)

    Shaowu Cheng

    2016-10-01

    Full Text Available Bus fare equity has attracted significant attention in China in the past few years. Compared with developed countries, China’s intelligent transportation systems are in their infancy, with immature bus fare policies being used in many public transit systems. The methods used for evaluating public transit fare equity in developed countries compare different fare policies based on rich data and cannot be directly applied in developing countries like China. In this paper, we present a method that uses IC card data, bus-mounted GPS data, and relevant statistical yearbook data to evaluate the equity of flat bus fare. The method ranks the factors that influence the impacts of bus fare on social equity for different passenger groups and indicates that trip distance and passenger boarding time are the two primary factors for bus fare equity from a resource allocation perspective. Finally, we present a case study that evaluates the flat fare policy for route 204 in Suzhou using the proposed method. The results show that the proposed method is feasible.

  7. An observational comparison of the older and younger bus passenger experience in a developing world city.

    Science.gov (United States)

    Aceves-González, Carlos; May, Andrew; Cook, Sharon

    2016-06-01

    This study was an unobtrusive observational analysis of 333 older and younger bus passengers in Guadalajara, Mexico. A set of data were collected for each observed passenger, as well as more general observations related to driver behaviour, bus design and bus service characteristics. There were significant differences between older and younger passengers in terms of boarding and alighting times, use of handrails, seat location preferences, passenger stability and coping strategies in order to maintain postural stability. The conditions of travel are conducive to a poor passenger experience for the older passengers in particular. Although the problems may be attributed to bus design and driver behaviour typical of that in developing countries, they are also influenced by the wider transport infrastructure, and a lack of a regulatory regime which places drivers under time pressure and in direct competition with each other. Practitioner Summary: Bus services must cater for all ages of passengers, including the elderly. This unobtrusive observational study investigated the passenger experience in a developing world city. Bus and wider service design were found to compromise the journey experience, with the older users being particularly negatively impacted. Design recommendations are provided.

  8. Bus Travel Time Deviation Analysis Using Automatic Vehicle Location Data and Structural Equation Modeling

    Directory of Open Access Journals (Sweden)

    Xiaolin Gong

    2015-01-01

    Full Text Available To investigate the influences of causes of unreliability and bus schedule recovery phenomenon on microscopic segment-level travel time variance, this study adopts Structural Equation Modeling (SEM to specify, estimate, and measure the theoretical proposed models. The SEM model establishes and verifies hypotheses for interrelationships among travel time deviations, departure delays, segment lengths, dwell times, and number of traffic signals and access connections. The finally accepted model demonstrates excellent fitness. Most of the hypotheses are supported by the sample dataset from bus Automatic Vehicle Location system. The SEM model confirms the bus schedule recovery phenomenon. The departure delays at bus terminals and upstream travel time deviations indeed have negative impacts on travel time fluctuation of buses en route. Meanwhile, the segment length directly and negatively impacts travel time variability and inversely positively contributes to the schedule recovery process; this exogenous variable also indirectly and positively influences travel times through the existence of signalized intersections and access connections. This study offers a rational approach to analyzing travel time deviation feature. The SEM model structure and estimation results facilitate the understanding of bus service performance characteristics and provide several implications for bus service planning, management, and operation.

  9. EtherBone - A Network Layer for the Wishbone SoC Bus

    CERN Document Server

    Kreider, M; Lewis, J; Włostowski, T; Serrano, J

    2011-01-01

    Today, there are several System on a Chip (SoC) bus systems. Typically, these buses are confined on-chip and rely on higher level components to communicate with the outside world. Taking these systems a step further, we see the possibility of extending the reach of the SoC bus to remote FPGAs or processors. This leads to the idea of the EtherBone (EB) core, which connects a Wishbone (WB) Ver. 4 Bus via a Gigabit Ethernet based network link to remote peripheral devices. EB acts as a transparent interconnect module towards attached WB Bus devices. Address information and data from one or more WB bus cycles is preceded with a descriptive header and encapsulated in a UDP/IP packet. Because of this standard compliance, EB is able to traverse Wide Area Networks and is therefore not bound to a geographic location. Due to the low level nature of the WB bus, EB provides a sound basis for remote hardware tools like a JTAG debugger, In-System-Programmer (ISP), boundary scan interface or logic analyser module. EB was de...

  10. ETHERBONE - a network layer for the wishbone SoC bus

    International Nuclear Information System (INIS)

    Kreider, M.; Terpstra, W.; Lewis, J.; Serrano, J.; Wlostowski, T.

    2012-01-01

    Today, there are several System on a Chip (SoC) bus systems. Typically, these buses are confined on-chip and rely on higher level components to communicate with the outside world. Taking these systems a step further, we see the possibility of extending the reach of the SoC bus to remote FPGAs or processors. This leads to the idea of the EtherBone (EB) core, which connects a Wishbone (WB) Ver. 4 Bus via a Gigabit Ethernet based network link to remote peripheral devices. EB acts as a transparent interconnect module towards attached WB Bus devices. Address information and data from one or more WB bus cycles is preceded with a descriptive header and encapsulated in a UDP/IP packet. Because of this standard compliance, EB is able to traverse Wide Area Networks and is therefore not bound to a geographic location. Due to the low level nature of the WB bus, EB provides a sound basis for remote hardware tools like a JTAG debugger, In-System-Programmer (ISP), boundary scan interface or logic analyser module. EB was developed in the scope of the White-Rabbit Timing Project (WR) at CERN and GSI/FAIR, which employs GigaBit Ethernet technology to communicate with memory mapped slave devices. WR will make use of EB as means to issue commands to its timing nodes and control connected accelerator hardware. (authors)

  11. An interconnecting bus power optimization method combining interconnect wire spacing with wire ordering

    International Nuclear Information System (INIS)

    Zhu Zhang-Ming; Hao Bao-Tian; En Yun-Fei; Yang Yin-Tang; Li Yue-Jin

    2011-01-01

    On-chip interconnect buses consume tens of percents of dynamic power in a nanometer scale integrated circuit and they will consume more power with the rapid scaling down of technology size and continuously rising clock frequency, therefore it is meaningful to lower the interconnecting bus power in design. In this paper, a simple yet accurate interconnect parasitic capacitance model is presented first and then, based on this model, a novel interconnecting bus optimization method is proposed. Wire spacing is a process for spacing wires for minimum dynamic power, while wire ordering is a process that searches for wire orders that maximally enhance it. The method, i.e., combining wire spacing with wire ordering, focuses on bus dynamic power optimization with a consideration of bus performance requirements. The optimization method is verified based on various nanometer technology parameters, showing that with 50% slack of routing space, 25.71% and 32.65% of power can be saved on average by the proposed optimization method for a global bus and an intermediate bus, respectively, under a 65-nm technology node, compared with 21.78% and 27.68% of power saved on average by uniform spacing technology. The proposed method is especially suitable for computer-aided design of nanometer scale on-chip buses. (interdisciplinary physics and related areas of science and technology)

  12. Evaluation of Effective Factors on Travel Time in Optimization of Bus Stops Placement Using Genetic Algorithm

    Science.gov (United States)

    Bargegol, Iraj; Ghorbanzadeh, Mahyar; Ghasedi, Meisam; Rastbod, Mohammad

    2017-10-01

    In congested cities, locating and proper designing of bus stops according to the unequal distribution of passengers is crucial issue economically and functionally, since this subject plays an important role in the use of bus system by passengers. Location of bus stops is a complicated subject; by reducing distances between stops, walking time decreases, but the total travel time may increase. In this paper, a specified corridor in the city of Rasht in north of Iran is studied. Firstly, a new formula is presented to calculate the travel time, by which the number of stops and consequently, the travel time can be optimized. An intended corridor with specified number of stops and distances between them is addressed, the related formulas to travel time are created, and its travel time is calculated. Then the corridor is modelled using a meta-heuristic method in order that the placement and the optimal distances of bus stops for that are determined. It was found that alighting and boarding time along with bus capacity are the most effective factors affecting travel time. Consequently, it is better to have more concentration on indicated factors for improving the efficiency of bus system.

  13. Optimal Design of the Feeder-Bus Network Based on the Transfer System

    Directory of Open Access Journals (Sweden)

    Lianbo Deng

    2013-01-01

    Full Text Available This paper studied the classic feeder-bus network design problem (FBNDP, which can be described as follows: for the passenger travel demand between rail stations and bus stops on a given urban transit network, it designs the optimal feeder bus routes and frequencies so as to minimize the passengers’ travel expense and the operator’s cost. We extended the demand pattern of M-to-1 in most existing researches to M-to-M. We comprehensively considered the passenger travel cost, which includes the waiting and riding cost on the bus, riding cost on rail, and transfer cost between these two transportation modes, and presented a new genetic algorithm that determines the optimal feeder-bus operating frequencies under strict constraint conditions. The numerical examples under different demand patterns have been experienced and analysed, which showed the robustness and efficiency of the presented algorithm. We also found that the distribution pattern of the travel demand has a significant influence on the feeder-bus network construction.

  14. Modelling modal shift due to the enhanced level of bus service

    Directory of Open Access Journals (Sweden)

    P. Vedagiri

    2009-06-01

    Full Text Available This study is concerned with the estimation of the probable shift of auto-rickshaw (three wheeled motorized para-transit vehicle users to the bus due to an increase in its level of service after providing exclusive bus lanes on Indian city roads carrying heterogeneous traffic. The quantum of an increase in the level of bus service due to the introduction of an exclusive bus lane was determined using a recently developed simulation model of heterogeneous traffic flow. The data on other factors (variables that might cause modal shift from the auto-rickshaw to the bus was collected conducting a home-interview survey based on the stated preference approach. A binary logit model of mode-choice was then calibrated using the collected data and the model was also validated using a holdout sample. A mode-choice probability curve to depict the possible shift of auto-rickshaw users to the bus is developed taking difference in the travel times of two-modes as the basis to serve as a user friendly tool to analyze the possible modal shift for a wide range of the values of the involved variables.

  15. An Integrative Risk Management/Governance Framework for Homeland Security Decision Making

    Science.gov (United States)

    2008-03-01

    key modes of transportation include highways, motor carrier (trucking), motor coach ( intercity bus), maritime, pipeline, rail (passenger and freight...2004 Overview: A blast tore apart a metro train car in Moscow during the morning rush hour on February 6, 2004. The train was traveling between the...Circle Line train, No. 204, traveling from Liverpool Street to Aldgate Station. Within one minute, a second explosion took place on Circle Line train

  16. Research on a Novel Hydraulic/Electric Synergy Bus

    Directory of Open Access Journals (Sweden)

    Kegang Zhao

    2017-12-01

    Full Text Available In recent years, increasing concerns regarding environmental pollution and requirements for lower fossil fuel consumption have increased interest in alternative hybrid powertrains. As a result, this paper presents a novel hydraulic/electric synergy powertrain with multiple working modes. The three energy sources (i.e., engine, battery, and hydraulic accumulator in this configuration are regulated by a dual planetary gear set to achieve optimal performances. This paper selects the component sizes of a hybrid electric vehicle (HEV, a hydraulic hybrid vehicle (HHV, and a hydraulic/electric synergy vehicle (HESV, based on the dynamic performance of a target vehicle (TV. In addition, this paper develops the forward simulation models of the four aforementioned vehicles in the MATLAB/Simulink/Driveline platform, in which the fuel economy simulations are carried out in relation to the Chinese urban bus cycle. The simulation results show that the fuel consumption of the three hybrid vehicles is similar, but much better than, that of the TV. Finally, based on the operating cost calculations over a five-year working period, the lowest cost ranges of the three hybrid vehicles are determined, which provides a method for choosing the optimal hybrid scheme.

  17. Adaptive UIX Layer for University Information SOA-BUS

    Directory of Open Access Journals (Sweden)

    Octavian DOSPINESCU

    2017-01-01

    Full Text Available The user interface (UI layer is considered one of the key components of software applications since it connects their end-users to functionalities. Well-engineered and robust software applications could eventually fail to be adopted due to a weak UI layer. In the current market, when creating sites, UI designers have to determine how to plan the best interface according to the devices of the users, namely desktops, laptops, tablets or smartphones. Having this in mind, the current paper aims to present the adaptive UIX Layer for a University Information SOA-Bus (UISB – a topic discussed in previous works [1], [2]. In this respect, we reviewed the literature on responsive and adaptive web design in order to identify the best front-end approach to the UISB. According to our findings, there is a strong debate in the academic field as well in the IT business in what concerns UI design. Recent interests have shown that the new trend in drafting the front-end layer is choosing between a responsive and an adaptive design. While arguments provided by both sides have failed to ease the decision makers’ choices on what type of design to choose, we aim to bring some light on the subject by proposing different layers for the UISB.

  18. System Interconnect Bus (SIB) compatible multi crate CAMAC Controller (CC)

    International Nuclear Information System (INIS)

    Jha, K.; Borkar, S.P.; Ghodgaonkar, M.D.; D'Costa, C.

    2001-01-01

    This paper describes design of SIB compatible crate controller with PC interface. SIB is a general-purpose parallel 1/O interface bus used for connecting multi crate system with single PC-interface. The crate controller comprises of a dedicated PC-AT add-on SIB interface card and two width CAMAC module designed to work at station 24 and station 25 of CAMAC crate. PC Interface card (SIBINT) is used for communication between PC/AT host computer and CAMAC Crates. The controller module incorporates a set of registers, logic to generate CAMAC data way timing. Transmission protocol used is RS485 standard. This controller is used for multiple CAMAC crates system, interfaced to PC, using a 60 core twisted pair flat ribbon cable. The crate controller is developed for use in process control, general-purpose data acquisition and control system and laboratory automation. Sustained data transfer rate achieved by controller is 115 Kword/sec each word being 32 bits in length. (author)

  19. Modified network simulation model with token method of bus access

    Directory of Open Access Journals (Sweden)

    L.V. Stribulevich

    2013-08-01

    Full Text Available Purpose. To study the characteristics of the local network with the marker method of access to the bus its modified simulation model was developed. Methodology. Defining characteristics of the network is carried out on the developed simulation model, which is based on the state diagram-layer network station with the mechanism of processing priorities, both in steady state and in the performance of control procedures: the initiation of a logical ring, the entrance and exit of the station network with a logical ring. Findings. A simulation model, on the basis of which can be obtained the dependencies of the application the maximum waiting time in the queue for different classes of access, and the reaction time usable bandwidth on the data rate, the number of network stations, the generation rate applications, the number of frames transmitted per token holding time, frame length was developed. Originality. The technique of network simulation reflecting its work in the steady condition and during the control procedures, the mechanism of priority ranking and handling was proposed. Practical value. Defining network characteristics in the real-time systems on railway transport based on the developed simulation model.

  20. Evolution of weighted complex bus transit networks with flow

    Science.gov (United States)

    Huang, Ailing; Xiong, Jie; Shen, Jinsheng; Guan, Wei

    2016-02-01

    Study on the intrinsic properties and evolutional mechanism of urban public transit networks (PTNs) has great significance for transit planning and control, particularly considering passengers’ dynamic behaviors. This paper presents an empirical analysis for exploring the complex properties of Beijing’s weighted bus transit network (BTN) based on passenger flow in L-space, and proposes a bi-level evolution model to simulate the development of transit routes from the view of complex network. The model is an iterative process that is driven by passengers’ travel demands and dual-controlled interest mechanism, which is composed of passengers’ spatio-temporal requirements and cost constraint of transit agencies. Also, the flow’s dynamic behaviors, including the evolutions of travel demand, sectional flow attracted by a new link and flow perturbation triggered in nearby routes, are taken into consideration in the evolutional process. We present the numerical experiment to validate the model, where the main parameters are estimated by using distribution functions that are deduced from real-world data. The results obtained have proven that our model can generate a BTN with complex properties, such as the scale-free behavior or small-world phenomenon, which shows an agreement with our empirical results. Our study’s results can be exploited to optimize the real BTN’s structure and improve the network’s robustness.