WorldWideScience

Sample records for intelligent on-board processing

  1. Employee on Boarding Process Automation

    OpenAIRE

    Khushboo Nalband; Priyanka Jadhav; Geetanjali Salunke

    2017-01-01

    On boarding, also known as organizational socialization, plays a vital role in building the initial relationship between an organization and an employee. It also contributes to an employees’ satisfaction, better performance and greater organizational commitment thus increasing an employees’ effectiveness and productivity in his/her role. Therefore, it is essential that on boarding process of an organization is efficient and effective to improve new employees’ retention. Generally this on boar...

  2. On-board processing for telecommunications satellites

    Science.gov (United States)

    Nuspl, P. P.; Dong, G.

    1991-01-01

    In this decade, communications satellite systems will probably face dramatic challenges from alternative transmission means. To balance and overcome such competition, and to prepare for new requirements, INTELSAT has developed several on-board processing techniques, including Satellite-Switched TDMA (SS-TDMA), Satellite-Switched FDMA (SS-FDMA), several Modulators/Demodulators (Modem), a Multicarrier Multiplexer and Demodulator MCDD), an International Business Service (IBS)/Intermediate Data Rate (IDR) BaseBand Processor (BBP), etc. Some proof-of-concept hardware and software were developed, and tested recently in the INTELSAT Technical Laboratories. These techniques and some test results are discussed.

  3. Flight Hardware Virtualization for On-Board Science Data Processing

    Data.gov (United States)

    National Aeronautics and Space Administration — Utilize Hardware Virtualization technology to benefit on-board science data processing by investigating new real time embedded Hardware Virtualization solutions and...

  4. On-board processing of video image sequences

    DEFF Research Database (Denmark)

    Andersen, Jakob Dahl; Chanrion, Olivier Arnaud; Forchhammer, Søren

    2008-01-01

    and evaluated. On-board there are six video cameras each capturing images of 1024times1024 pixels of 12 bpp at a frame rate of 15 fps, thus totalling 1080 Mbits/s. In comparison the average downlink data rate for these images is projected to be 50 kbit/s. This calls for efficient on-board processing to select...

  5. Intelligent agents for training on-board fire fighting

    NARCIS (Netherlands)

    Bosch, K. van den; Harbers, M.; Heuvelink, A.; Doesburg, W. van

    2009-01-01

    Simulation-based training in complex decision making often requires ample personnel for playing various roles (e.g. team mates, adversaries). Using intelligent agents may diminish the need for staff. However, to achieve goal-directed training, events in the simulation as well as the behavior of key

  6. On board fuel processing for using in electric vehicles

    International Nuclear Information System (INIS)

    Paez, Daniel E.; Marquez, Marco A.

    1999-01-01

    The increase in vehicle population, the emission effects upon the environment, and the growing concern of industrialized nations to reduce oil dependency, are the arguments for the new developments that may change the automobile revolution within the next decades. However, the electricity to move the future vehicles must come from the processing of liquid fuels on board. Liquid fuels such as gasoline have the advantage of having good on-site system for distribution and supply directly to the vehicle and will compete for staying as the energy source of the future. What are the opportunities in R and D and how to take advantage of them are analyzed in this document. Liquid fuel processing technologies and fuel options are also described by PDVSA-INTEVEP

  7. Reconfigurable On-Board Vision Processing for Small Autonomous Vehicles

    Directory of Open Access Journals (Sweden)

    James K. Archibald

    2006-12-01

    Full Text Available This paper addresses the challenge of supporting real-time vision processing on-board small autonomous vehicles. Local vision gives increased autonomous capability, but it requires substantial computing power that is difficult to provide given the severe constraints of small size and battery-powered operation. We describe a custom FPGA-based circuit board designed to support research in the development of algorithms for image-directed navigation and control. We show that the FPGA approach supports real-time vision algorithms by describing the implementation of an algorithm to construct a three-dimensional (3D map of the environment surrounding a small mobile robot. We show that FPGAs are well suited for systems that must be flexible and deliver high levels of performance, especially in embedded settings where space and power are significant concerns.

  8. Reconfigurable On-Board Vision Processing for Small Autonomous Vehicles

    Directory of Open Access Journals (Sweden)

    Fife WadeS

    2007-01-01

    Full Text Available This paper addresses the challenge of supporting real-time vision processing on-board small autonomous vehicles. Local vision gives increased autonomous capability, but it requires substantial computing power that is difficult to provide given the severe constraints of small size and battery-powered operation. We describe a custom FPGA-based circuit board designed to support research in the development of algorithms for image-directed navigation and control. We show that the FPGA approach supports real-time vision algorithms by describing the implementation of an algorithm to construct a three-dimensional (3D map of the environment surrounding a small mobile robot. We show that FPGAs are well suited for systems that must be flexible and deliver high levels of performance, especially in embedded settings where space and power are significant concerns.

  9. Flight Hardware Virtualization for On-Board Science Data Processing Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Utilize Hardware Virtualization technology to benefit on-board science data processing by investigating new real time embedded Hardware Virtualization solutions and...

  10. Clinical Process Intelligence

    DEFF Research Database (Denmark)

    Vilstrup Pedersen, Klaus

    2006-01-01

    .e. local guidelines. From a knowledge management point of view, this externalization of generalized processes, gives the opportunity to learn from, evaluate and optimize the processes. "Clinical Process Intelligence" (CPI), will denote the goal of getting generalized insight into patient centered health...

  11. Business process intelligence

    NARCIS (Netherlands)

    Castellanos, M.; Alves De Medeiros, A.K.; Mendling, J.; Weber, B.; Weijters, A.J.M.M.; Cardoso, J.; Aalst, van der W.M.P.

    2009-01-01

    Business Process Intelligence (BPI,) is an emerging area that is getting increasingly popularfor enterprises. The need to improve business process efficiency, to react quickly to changes and to meet regulatory compliance is among the main drivers for BPI. BPI refers to the application of Business

  12. Autonomous, On-board Processing for Sensor Systems

    Data.gov (United States)

    National Aeronautics and Space Administration — Fuse high performance reconfigurable processors with emerging fault-tolerance & autonomous processing techniques for a 10-100x decrease in processing time. This...

  13. On Board Data Acquisition System with Intelligent Transducers for Unmanned Aerial Vehicles

    Science.gov (United States)

    Rochala, Zdzisław

    2012-02-01

    This report presents conclusions from research project no. ON50900363 conducted at the Mechatronics Department, Military University of Technology in the years 2007-2010. As the main object of the study involved the preparation of a concept and the implementation of an avionics data acquisition system intended for research during flight of unmanned aerial vehicles of the mini class, this article presents a design of an avionics system and describes equipment solutions of a distributed measurement system intended for data acquisition consisting of intelligent transducers. The data collected during a flight controlled by an operator confirmed proper operation of the individual components of the data acquisition system.

  14. High-Speed On-Board Data Processing for Science Instruments

    Science.gov (United States)

    Beyon, Jeffrey Y.; Ng, Tak-Kwong; Lin, Bing; Hu, Yongxiang; Harrison, Wallace

    2014-01-01

    A new development of on-board data processing platform has been in progress at NASA Langley Research Center since April, 2012, and the overall review of such work is presented in this paper. The project is called High-Speed On-Board Data Processing for Science Instruments (HOPS) and focuses on a high-speed scalable data processing platform for three particular National Research Council's Decadal Survey missions such as Active Sensing of CO2 Emissions over Nights, Days, and Seasons (ASCENDS), Aerosol-Cloud-Ecosystems (ACE), and Doppler Aerosol Wind Lidar (DAWN) 3-D Winds. HOPS utilizes advanced general purpose computing with Field Programmable Gate Array (FPGA) based algorithm implementation techniques. The significance of HOPS is to enable high speed on-board data processing for current and future science missions with its reconfigurable and scalable data processing platform. A single HOPS processing board is expected to provide approximately 66 times faster data processing speed for ASCENDS, more than 70% reduction in both power and weight, and about two orders of cost reduction compared to the state-of-the-art (SOA) on-board data processing system. Such benchmark predictions are based on the data when HOPS was originally proposed in August, 2011. The details of these improvement measures are also presented. The two facets of HOPS development are identifying the most computationally intensive algorithm segments of each mission and implementing them in a FPGA-based data processing board. A general introduction of such facets is also the purpose of this paper.

  15. Intelligent multivariate process supervision

    International Nuclear Information System (INIS)

    Visuri, Pertti.

    1986-01-01

    This thesis addresses the difficulties encountered in managing large amounts of data in supervisory control of complex systems. Some previous alarm and disturbance analysis concepts are reviewed and a method for improving the supervision of complex systems is presented. The method, called multivariate supervision, is based on adding low level intelligence to the process control system. By using several measured variables linked together by means of deductive logic, the system can take into account the overall state of the supervised system. Thus, it can present to the operators fewer messages with higher information content than the conventional control systems which are based on independent processing of each variable. In addition, the multivariate method contains a special information presentation concept for improving the man-machine interface. (author)

  16. Information processing requirements for on-board monitoring of automatic landing

    Science.gov (United States)

    Sorensen, J. A.; Karmarkar, J. S.

    1977-01-01

    A systematic procedure is presented for determining the information processing requirements for on-board monitoring of automatic landing systems. The monitoring system detects landing anomalies through use of appropriate statistical tests. The time-to-correct aircraft perturbations is determined from covariance analyses using a sequence of suitable aircraft/autoland/pilot models. The covariance results are used to establish landing safety and a fault recovery operating envelope via an event outcome tree. This procedure is demonstrated with examples using the NASA Terminal Configured Vehicle (B-737 aircraft). The procedure can also be used to define decision height, assess monitoring implementation requirements, and evaluate alternate autoland configurations.

  17. On-board Payload Data Processing from Earth to Space Segment

    Science.gov (United States)

    Tragni, M.; Abbattista, C.; Amoruso, L.; Cinquepalmi, L.; Bgongiari, F.; Errico, W.

    2013-09-01

    Matching the users application requirements with the more and more huge data streaming of the satellite missions is becoming very complex. But we need both of them. To face both the data management (memory availability) and their transmission (band availability) many recent R&D activities are studying the right way to move the data processing from the ground segment to the space segment by the development of the so-called On-board Payload Data Processing (OPDP). The space designer are trying to find new strategies to increase the on board computation capacity and its viability to overcome such limitations, memory and band, focusing the transmission of remote sensing information (not only data) towards their final use. Some typical applications which can benefit of the on board payload data processing include the automatic control of a satellites constellation which can modify its scheduled acquisitions directly on-board and according to the information extracted from the just acquired data, increasing, for example, the capability of monitoring a specific objective (such as oil spills, illegal traffic) with a greater versatility than a traditional ground segment workflow. The authors and their companies can count on a sound experience in design and development of open, modular and compact on-board processing systems. Actually they are involved in a program, the Space Payload Data Processing (SpacePDP) whose main objective is to develop an hardware and a software framework able to perform both the space mission standard tasks (sensors control, mass storage devices management, uplink and downlink) and the specific tasks required by each mission. SpacePDP is an Open and modular Payload Data Processing system, composed of Hardware and Software modules included a SDK. The whole system is characterised by flexible and customizable building blocks that form the system architectures and by a very easy way to be integrated in the missions by the SDK (a development

  18. Real-Time On-Board Airborne Demonstration of High-Speed On-Board Data Processing for Science Instruments (HOPS)

    Science.gov (United States)

    Beyon, Jeffrey Y.; Ng, Tak-Kwong; Davis, Mitchell J.; Adams, James K.; Bowen, Stephen C.; Fay, James J.; Hutchinson, Mark A.

    2015-01-01

    The project called High-Speed On-Board Data Processing for Science Instruments (HOPS) has been funded by NASA Earth Science Technology Office (ESTO) Advanced Information Systems Technology (AIST) program since April, 2012. The HOPS team recently completed two flight campaigns during the summer of 2014 on two different aircrafts with two different science instruments. The first flight campaign was in July, 2014 based at NASA Langley Research Center (LaRC) in Hampton, VA on the NASA's HU-25 aircraft. The science instrument that flew with HOPS was Active Sensing of CO2 Emissions over Nights, Days, and Seasons (ASCENDS) CarbonHawk Experiment Simulator (ACES) funded by NASA's Instrument Incubator Program (IIP). The second campaign was in August, 2014 based at NASA Armstrong Flight Research Center (AFRC) in Palmdale, CA on the NASA's DC-8 aircraft. HOPS flew with the Multifunctional Fiber Laser Lidar (MFLL) instrument developed by Excelis Inc. The goal of the campaigns was to perform an end-to-end demonstration of the capabilities of the HOPS prototype system (HOPS COTS) while running the most computationally intensive part of the ASCENDS algorithm real-time on-board. The comparison of the two flight campaigns and the results of the functionality tests of the HOPS COTS are presented in this paper.

  19. High-Speed On-Board Data Processing for Science Instruments: HOPS

    Science.gov (United States)

    Beyon, Jeffrey

    2015-01-01

    The project called High-Speed On-Board Data Processing for Science Instruments (HOPS) has been funded by NASA Earth Science Technology Office (ESTO) Advanced Information Systems Technology (AIST) program during April, 2012 â€" April, 2015. HOPS is an enabler for science missions with extremely high data processing rates. In this three-year effort of HOPS, Active Sensing of CO2 Emissions over Nights, Days, and Seasons (ASCENDS) and 3-D Winds were of interest in particular. As for ASCENDS, HOPS replaces time domain data processing with frequency domain processing while making the real-time on-board data processing possible. As for 3-D Winds, HOPS offers real-time high-resolution wind profiling with 4,096-point fast Fourier transform (FFT). HOPS is adaptable with quick turn-around time. Since HOPS offers reusable user-friendly computational elements, its FPGA IP Core can be modified for a shorter development period if the algorithm changes. The FPGA and memory bandwidth of HOPS is 20 GB/sec while the typical maximum processor-to-SDRAM bandwidth of the commercial radiation tolerant high-end processors is about 130-150 MB/sec. The inter-board communication bandwidth of HOPS is 4 GB/sec while the effective processor-to-cPCI bandwidth of commercial radiation tolerant high-end boards is about 50-75 MB/sec. Also, HOPS offers VHDL cores for the easy and efficient implementation of ASCENDS and 3-D Winds, and other similar algorithms. A general overview of the 3-year development of HOPS is the goal of this presentation.

  20. Computational Intelligence in Image Processing

    CERN Document Server

    Siarry, Patrick

    2013-01-01

    Computational intelligence based techniques have firmly established themselves as viable, alternate, mathematical tools for more than a decade. They have been extensively employed in many systems and application domains, among these signal processing, automatic control, industrial and consumer electronics, robotics, finance, manufacturing systems, electric power systems, and power electronics. Image processing is also an extremely potent area which has attracted the atten­tion of many researchers who are interested in the development of new computational intelligence-based techniques and their suitable applications, in both research prob­lems and in real-world problems. Part I of the book discusses several image preprocessing algorithms; Part II broadly covers image compression algorithms; Part III demonstrates how computational intelligence-based techniques can be effectively utilized for image analysis purposes; and Part IV shows how pattern recognition, classification and clustering-based techniques can ...

  1. Aktuelles Schlagwort: Business Process Intelligence

    NARCIS (Netherlands)

    Mutschler, B.B.; Reichert, M.U.

    In jüngerer Vergangenheit rückt vermehrt die Erfassung und Analyse von Prozessechtdaten (z.B. zum Start und Ende von Prozessaktivitäten) in den Blickpunkt. Solche Daten werden von den meisten prozessorientierten Informationssystemen geliefert. Das Schlagwort Business Process Intelligence (BPI)

  2. Business Intelligence in Process Control

    Science.gov (United States)

    Kopčeková, Alena; Kopček, Michal; Tanuška, Pavol

    2013-12-01

    The Business Intelligence technology, which represents a strong tool not only for decision making support, but also has a big potential in other fields of application, is discussed in this paper. Necessary fundamental definitions are offered and explained to better understand the basic principles and the role of this technology for company management. Article is logically divided into five main parts. In the first part, there is the definition of the technology and the list of main advantages. In the second part, an overview of the system architecture with the brief description of separate building blocks is presented. Also, the hierarchical nature of the system architecture is shown. The technology life cycle consisting of four steps, which are mutually interconnected into a ring, is described in the third part. In the fourth part, analytical methods incorporated in the online analytical processing and data mining used within the business intelligence as well as the related data mining methodologies are summarised. Also, some typical applications of the above-mentioned particular methods are introduced. In the final part, a proposal of the knowledge discovery system for hierarchical process control is outlined. The focus of this paper is to provide a comprehensive view and to familiarize the reader with the Business Intelligence technology and its utilisation.

  3. Machine intelligence and signal processing

    CERN Document Server

    Vatsa, Mayank; Majumdar, Angshul; Kumar, Ajay

    2016-01-01

    This book comprises chapters on key problems in machine learning and signal processing arenas. The contents of the book are a result of a 2014 Workshop on Machine Intelligence and Signal Processing held at the Indraprastha Institute of Information Technology. Traditionally, signal processing and machine learning were considered to be separate areas of research. However in recent times the two communities are getting closer. In a very abstract fashion, signal processing is the study of operator design. The contributions of signal processing had been to device operators for restoration, compression, etc. Applied Mathematicians were more interested in operator analysis. Nowadays signal processing research is gravitating towards operator learning – instead of designing operators based on heuristics (for example wavelets), the trend is to learn these operators (for example dictionary learning). And thus, the gap between signal processing and machine learning is fast converging. The 2014 Workshop on Machine Intel...

  4. Artificial intelligence and process management

    International Nuclear Information System (INIS)

    Epton, J.B.A.

    1989-01-01

    Techniques derived from work in artificial intelligence over the past few decades are beginning to change the approach in applying computers to process management. To explore this new approach and gain real practical experience of its potential a programme of experimental applications was initiated by Sira in collaboration with the process industry. This programme encompassed a family of experimental applications ranging from process monitoring, through supervisory control and troubleshooting to planning and scheduling. The experience gained has led to a number of conclusions regarding the present level of maturity of the technology, the potential for further developments and the measures required to secure the levels of system integrity necessary in on-line applications to critical processes. (author)

  5. Combined on-board hydride slurry storage and reactor system and process for hydrogen-powered vehicles and devices

    Science.gov (United States)

    Brooks, Kriston P; Holladay, Jamelyn D; Simmons, Kevin L; Herling, Darrell R

    2014-11-18

    An on-board hydride storage system and process are described. The system includes a slurry storage system that includes a slurry reactor and a variable concentration slurry. In one preferred configuration, the storage system stores a slurry containing a hydride storage material in a carrier fluid at a first concentration of hydride solids. The slurry reactor receives the slurry containing a second concentration of the hydride storage material and releases hydrogen as a fuel to hydrogen-power devices and vehicles.

  6. On Gamma Ray Instrument On-Board Data Processing Real-Time Computational Algorithm for Cosmic Ray Rejection

    Science.gov (United States)

    Kizhner, Semion; Hunter, Stanley D.; Hanu, Andrei R.; Sheets, Teresa B.

    2016-01-01

    gamma ray events and the problem is to detect and reject the much more voluminous cosmic ray projections, so that the remaining science data can be telemetered to the ground over the constrained communication link. The state-of-the-art in cosmic rays detection and rejection does not provide an adequate computational solution. This paper presents a novel approach to the AdEPT on-board data processing burdened with the CR detection top pole bottleneck problem. This paper is introducing the data processing object, demonstrates object segmentation and distribution for processing among many processing elements (PEs) and presents solution algorithm for the processing bottleneck - the CR-Algorithm. The algorithm is based on the a priori knowledge that a CR pierces the entire instrument pressure vessel. This phenomenon is also the basis for a straightforward CR simulator, allowing the CR-Algorithm performance testing. Parallel processing of the readout image's (2(N+M) - 4) peripheral voxels is detecting all CRs, resulting in O(n) computational complexity. This algorithm near real-time performance is making AdEPT class spaceflight instruments feasible.

  7. On-board event processing algorithms for a CCD-based space borne X-ray spectrometer

    International Nuclear Information System (INIS)

    Chun, H.J.; Bowles, J.A.; Branduardi-Raymont, G.; Gowen, R.A.

    1996-01-01

    This paper describes two alternative algorithms which are applied to reduce the telemetry requirements for a Charge Coupled Device (CCD) based, space-borne, X-ray spectrometer by on-board reconstruction of the X-ray events split over two or more adjacent pixels. The algorithms have been developed for the Reflection Grating Spectrometer (RGS) on the X-ray multi-mirror (XMM) mission, the second cornerstone project in the European Space Agency's Horizon 2000 programme. The overall instrument and some criteria which provide the background of the development of the algorithms, implemented in Tartan ADA on an MA31750 microprocessor, are described. The on-board processing constraints and requirements are discussed, and the performances of the algorithms are compared. Test results are presented which show that the recursive implementation is faster and has a smaller executable file although it uses more memory because of its stack requirements. (orig.)

  8. Report : business process intelligence challenge 2013

    NARCIS (Netherlands)

    Dongen, van B.F.; Weber, B.; Ferreira, D.R.; De Weerdt, J.; Lohmann, N.; Song, M.; Wohed, P.

    2014-01-01

    For the third time, the Business Process Intelligence workshop hosted the Business Process Intelligence Challenge. The goal of this challenge is twofold. On the one hand, the challenge allows researchers and practitioners in the field to show their analytical capabilities to a broader audience. On

  9. Intelligence amplification framework for enhancing scheduling processes

    NARCIS (Netherlands)

    Dobrkovic, Andrej; Liu, Luyao; Iacob, Maria Eugenia; van Hillegersberg, Jos

    2016-01-01

    The scheduling process in a typical business environment consists of predominantly repetitive tasks that have to be completed in limited time and often containing some form of uncertainty. The intelligence amplification is a symbiotic relationship between a human and an intelligent agent. This

  10. The Predictive Aspect of Business Process Intelligence

    DEFF Research Database (Denmark)

    Pérez, Moisés Lima; Møller, Charles

    2007-01-01

    This paper presents the arguments for a research proposal on predicting business events in a Business Process Intelligence (BPI) context. The paper argues that BPI holds a potential for leveraging enterprise benefits by supporting real-time processes. However, based on the experiences from past...... business intelligence projects the paper argues that it is necessary to establish a new methodology to mine and extract the intelligence on the business level which is different from that, which will improve a business process in an enterprise. In conclusion the paper proposes a new research project aimed...

  11. High-Speed On-Board Data Processing Platform for LIDAR Projects at NASA Langley Research Center

    Science.gov (United States)

    Beyon, J.; Ng, T. K.; Davis, M. J.; Adams, J. K.; Lin, B.

    2015-12-01

    The project called High-Speed On-Board Data Processing for Science Instruments (HOPS) has been funded by NASA Earth Science Technology Office (ESTO) Advanced Information Systems Technology (AIST) program during April, 2012 - April, 2015. HOPS is an enabler for science missions with extremely high data processing rates. In this three-year effort of HOPS, Active Sensing of CO2 Emissions over Nights, Days, and Seasons (ASCENDS) and 3-D Winds were of interest in particular. As for ASCENDS, HOPS replaces time domain data processing with frequency domain processing while making the real-time on-board data processing possible. As for 3-D Winds, HOPS offers real-time high-resolution wind profiling with 4,096-point fast Fourier transform (FFT). HOPS is adaptable with quick turn-around time. Since HOPS offers reusable user-friendly computational elements, its FPGA IP Core can be modified for a shorter development period if the algorithm changes. The FPGA and memory bandwidth of HOPS is 20 GB/sec while the typical maximum processor-to-SDRAM bandwidth of the commercial radiation tolerant high-end processors is about 130-150 MB/sec. The inter-board communication bandwidth of HOPS is 4 GB/sec while the effective processor-to-cPCI bandwidth of commercial radiation tolerant high-end boards is about 50-75 MB/sec. Also, HOPS offers VHDL cores for the easy and efficient implementation of ASCENDS and 3-D Winds, and other similar algorithms. A general overview of the 3-year development of HOPS is the goal of this presentation.

  12. On-board Data Processing to Lower Bandwidth Requirements on an Infrared Astronomy Satellite: Case of Herschel-PACS Camera

    Directory of Open Access Journals (Sweden)

    Christian Reimers

    2005-09-01

    Full Text Available This paper presents a new data compression concept, “on-board processing,” for infrared astronomy, where space observatories have limited processing resources. The proposed approach has been developed and tested for the PACS camera from the European Space Agency (ESA mission, Herschel. Using lossy and lossless compression, the presented method offers high compression ratio with a minimal loss of potentially useful scientific data. It also provides higher signal-to-noise ratio than that for standard compression techniques. Furthermore, the proposed approach presents low algorithmic complexity such that it is implementable on the resource-limited hardware. The various modules of the data compression concept are discussed in detail.

  13. Technology Readiness Level (TRL) Advancement of the MSPI On-Board Processing Platform for the ACE Decadal Survey Mission

    Science.gov (United States)

    Pingree, Paula J.; Werne, Thomas A.; Bekker, Dmitriy L.; Wilson, Thor O.

    2011-01-01

    The Xilinx Virtex-5QV is a new Single-event Immune Reconfigurable FPGA (SIRF) device that is targeted as the spaceborne processor for the NASA Decadal Survey Aerosol-Cloud-Ecosystem (ACE) mission's Multiangle SpectroPolarimetric Imager (MSPI) instrument, currently under development at JPL. A key technology needed for MSPI is on-board processing (OBP) to calculate polarimetry data as imaged by each of the 9 cameras forming the instrument. With funding from NASA's ESTO1 AIST2 Program, JPL is demonstrating how signal data at 95 Mbytes/sec over 16 channels for each of the 9 multi-angle cameras can be reduced to 0.45 Mbytes/sec, thereby substantially reducing the image data volume for spacecraft downlink without loss of science information. This is done via a least-squares fitting algorithm implemented on the Virtex-5 FPGA operating in real-time on the raw video data stream.

  14. THERMO-MECHANICALLY PROCESSED ROLLED WIRE FOR HIGH-STRENGTH ON-BOARD WIRE

    Directory of Open Access Journals (Sweden)

    V. A. Lutsenko

    2011-01-01

    Full Text Available It is shown that at twisting of wire of diameter 1,83 mm, produced by direct wire drawing of thermomechanically processed rolled wire of diameter 5,5 mm of steel 90, metal stratification is completely eliminated at decrease of carbon, manganese and an additional alloying of chrome.

  15. Towards a universal competitive intelligence process model

    Directory of Open Access Journals (Sweden)

    Rene Pellissier

    2013-08-01

    Full Text Available Background: Competitive intelligence (CI provides actionable intelligence, which provides a competitive edge in enterprises. However, without proper process, it is difficult to develop actionable intelligence. There are disagreements about how the CI process should be structured. For CI professionals to focus on producing actionable intelligence, and to do so with simplicity, they need a common CI process model.Objectives: The purpose of this research is to review the current literature on CI, to look at the aims of identifying and analysing CI process models, and finally to propose a universal CI process model.Method: The study was qualitative in nature and content analysis was conducted on all identified sources establishing and analysing CI process models. To identify relevant literature, academic databases and search engines were used. Moreover, a review of references in related studies led to more relevant sources, the references of which were further reviewed and analysed. To ensure reliability, only peer-reviewed articles were used.Results: The findings reveal that the majority of scholars view the CI process as a cycle of interrelated phases. The output of one phase is the input of the next phase.Conclusion: The CI process is a cycle of interrelated phases. The output of one phase is the input of the next phase. These phases are influenced by the following factors: decision makers, process and structure, organisational awareness and culture, and feedback.

  16. Data Processing and Primary results of Lunar Penetrating Radar on Board the Chinese Yutu Rover

    Science.gov (United States)

    Su, Yan; Xing, Shuguo; Feng, Jianqing; Dai, Shun; Ding, Chunyu; Xiao, Yuan; Zhang, Hongbo; Zhao, Shu; Xue, Xiping; Zhang, Xiaoxia; Liu, Bin; Yao, Meijuan; Li, Chunlai

    2015-04-01

    Radar is an attractive and powerful technique to observe the Moon. Radar mapping of the Moon's topography was first done by the Arecibo telescope at a wave- length of 70 cm in 1964 (Thompson & Dyce 1966). Chang'e-3 (CE-3) was successfully launched on 2013 December 2, and the landing place is in Mare Imbrium, about 40km south of the 6km diameter Laplace F crater, at 44.1214ON, 19.5116OW. The Lunar ground-Penetrating Radar (LPR) is one of scientific payloads of the Yutu rover, aiming to achieve the first direct measurements and explore the lunar subsurface structure. Compared with ALSE and LRS, LPR works at higher frequencies of 60 MHz and 500 MHz. Thus it can probe regions with shallower depth including the regolith and lunar crust at higher range resolution. The LPR uses one transmitting and one receiving dipole antenna for 60 MHz which are installed at the back of the rover. For 500 MHz, one transmitting and two bow-tie receiving antennas are attached to the bottom of the rover. It transmits a pulsed signal and receives the radar echo signal along the path that the Yutu rover traverses. The free space range resolutions are ~ 50 cm and ~ 25 m for 60 MHz and 500 MHz respectively. The radar data stop being sampled and are sent back to Earth when Yutu is stationary. Observations are simultaneously carried out at frequencies of 60 MHz and 500 MHz. Since the Yutu rover had severe problems during its second lunar day, it is pity that the Yutu rover only transversed a limited distance of 114.8m. In total, 566 MB of data were obtained. The scientific data are archived and distributed by National Astronomical Observatories, Chinese Academy of Sciences. Data processing has been done in order to eliminate the effect of the instrument. To obtain clear radar images, more data processing need to be applied such as coordinate transformation, data editing, background removal, the operations of smoothing and gain resetting. The radar signal could detect hundreds of meters deep at

  17. Parallel processing for artificial intelligence 1

    CERN Document Server

    Kanal, LN; Kumar, V; Suttner, CB

    1994-01-01

    Parallel processing for AI problems is of great current interest because of its potential for alleviating the computational demands of AI procedures. The articles in this book consider parallel processing for problems in several areas of artificial intelligence: image processing, knowledge representation in semantic networks, production rules, mechanization of logic, constraint satisfaction, parsing of natural language, data filtering and data mining. The publication is divided into six sections. The first addresses parallel computing for processing and understanding images. The second discus

  18. Intelligent medical image processing by simulated annealing

    International Nuclear Information System (INIS)

    Ohyama, Nagaaki

    1992-01-01

    Image processing is being widely used in the medical field and already has become very important, especially when used for image reconstruction purposes. In this paper, it is shown that image processing can be classified into 4 categories; passive, active, intelligent and visual image processing. These 4 classes are explained at first through the use of several examples. The results show that the passive image processing does not give better results than the others. Intelligent image processing, then, is addressed, and the simulated annealing method is introduced. Due to the flexibility of the simulated annealing, formulated intelligence is shown to be easily introduced in an image reconstruction problem. As a practical example, 3D blood vessel reconstruction from a small number of projections, which is insufficient for conventional method to give good reconstruction, is proposed, and computer simulation clearly shows the effectiveness of simulated annealing method. Prior to the conclusion, medical file systems such as IS and C (Image Save and Carry) is pointed out to have potential for formulating knowledge, which is indispensable for intelligent image processing. This paper concludes by summarizing the advantages of simulated annealing. (author)

  19. Intelligent process control operator aid -- An artificial intelligence approach

    International Nuclear Information System (INIS)

    Sharma, D.D.; Miller, D.D.; Hajek, B.; Chandrasekaran, B.

    1986-01-01

    This paper describes an approach for designing intelligent process and power plant control operator aids. It is argued that one of the key aspects of an intelligent operator aid is the capability for dynamic procedure synthesis with incomplete definition of initial state, unknown goal states, and the dynamic world situation. The dynamic world state is used to determine the goal, select appropriate plan steps from prespecified procedures to achieve the goal, control the execution of the synthesized plan, and provide for dynamic recovery from failure often using a goal hierarchy. The dynamic synthesis of a plan requires integration of various problems solving capabilities such as plan generation, plan synthesis, plan modification, and failure recovery from a plan. The programming language for implementing the DPS framework provides a convenient tool for developing applications. An application of the DPS approach to a Nuclear Power Plant emergency procedure synthesis is also described. Initial test results indicate that the approach is successful in dynamically synthesizing the procedures. The authors realize that the DPS framework is not a solution for all control tasks. However, many existing process and plant control problems satisfy the requirements discussed in the paper and should be able to benefit from the framework described

  20. New Perspectives on Intelligence Collection and Processing

    Science.gov (United States)

    2016-06-01

    MASINT Measurement and Signature Intelligence NPS Naval Postgraduate School OSINT Open Source Intelligence pdf Probability Density Function SIGINT...MASINT): different types of sensors • Open Source Intelligence ( OSINT ): from all open sources • Signals Intelligence (SIGINT): intercepting the

  1. Application of artificial intelligence in process control

    CERN Document Server

    Krijgsman, A

    1993-01-01

    This book is the result of a united effort of six European universities to create an overall course on the appplication of artificial intelligence (AI) in process control. The book includes an introduction to key areas including; knowledge representation, expert, logic, fuzzy logic, neural network, and object oriented-based approaches in AI. Part two covers the application to control engineering, part three: Real-Time Issues, part four: CAD Systems and Expert Systems, part five: Intelligent Control and part six: Supervisory Control, Monitoring and Optimization.

  2. Using Intelligent Agents to Manage Business Processes

    OpenAIRE

    Jennings, N. R.; Faratin, P.; Johnson, M. J.; O'Brien, P.; Wiegand, M. E.

    1996-01-01

    Management of the business process requires pertinent, consistent and up-to-date information gathering and information dissemination. These complex and time consuming tasks prompt organizations to develop an Information Technology system to assist with the management of various aspects of their business processes. Intelligent agents are the strongest solution candidates because of their many advantages, namely: autonomy, social ability, responsiveness and proactiveness. Given these characteri...

  3. Artificial intelligence applied to process signal analysis

    Science.gov (United States)

    Corsberg, Dan

    1988-01-01

    Many space station processes are highly complex systems subject to sudden, major transients. In any complex process control system, a critical aspect of the human/machine interface is the analysis and display of process information. Human operators can be overwhelmed by large clusters of alarms that inhibit their ability to diagnose and respond to a disturbance. Using artificial intelligence techniques and a knowledge base approach to this problem, the power of the computer can be used to filter and analyze plant sensor data. This will provide operators with a better description of the process state. Once a process state is recognized, automatic action could be initiated and proper system response monitored.

  4. Intelligent processing for thick composites

    Science.gov (United States)

    Shin, Daniel Dong-Ok

    2000-10-01

    Manufacturing thick composite parts are associated with adverse curing conditions such as large in-plane temperature gradient and exotherms. The condition is further aggravated because the manufacturer's cycle and the existing cure control systems do not adequately counter such affects. In response, the forecast-based thermal control system is developed to have better cure control for thick composites. Accurate cure kinetic model is crucial for correctly identifying the amount of heat generated for composite process simulation. A new technique for identifying cure parameters for Hercules AS4/3502 prepreg is presented by normalizing the DSC data. The cure kinetics is based on an autocatalytic model for the proposed method, which uses dynamic and isothermal DSC data to determine its parameters. Existing models are also used to determine kinetic parameters but rendered inadequate because of the material's temperature dependent final degree of cure. The model predictions determined from the new technique showed good agreement to both isothermal and dynamic DSC data. The final degree of cure was also in good agreement with experimental data. A realistic cure simulation model including bleeder ply analysis and compaction is validated with Hercules AS4/3501-6 based laminates. The nonsymmetrical temperature distribution resulting from the presence of bleeder plies agreed well to the model prediction. Some of the discrepancies in the predicted compaction behavior were attributed to inaccurate viscosity and permeability models. The temperature prediction was quite good for the 3cm laminate. The validated process simulation model along with cure kinetics model for AS4/3502 prepreg were integrated into the thermal control system. The 3cm Hercules AS4/3501-6 and AS4/3502 laminate were fabricated. The resulting cure cycles satisfied all imposed requirements by minimizing exotherms and temperature gradient. Although the duration of the cure cycles increased, such phenomena was

  5. On-Board Mining in the Sensor Web

    Science.gov (United States)

    Tanner, S.; Conover, H.; Graves, S.; Ramachandran, R.; Rushing, J.

    2004-12-01

    On-board data mining can contribute to many research and engineering applications, including natural hazard detection and prediction, intelligent sensor control, and the generation of customized data products for direct distribution to users. The ability to mine sensor data in real time can also be a critical component of autonomous operations, supporting deep space missions, unmanned aerial and ground-based vehicles (UAVs, UGVs), and a wide range of sensor meshes, webs and grids. On-board processing is expected to play a significant role in the next generation of NASA, Homeland Security, Department of Defense and civilian programs, providing for greater flexibility and versatility in measurements of physical systems. In addition, the use of UAV and UGV systems is increasing in military, emergency response and industrial applications. As research into the autonomy of these vehicles progresses, especially in fleet or web configurations, the applicability of on-board data mining is expected to increase significantly. Data mining in real time on board sensor platforms presents unique challenges. Most notably, the data to be mined is a continuous stream, rather than a fixed store such as a database. This means that the data mining algorithms must be modified to make only a single pass through the data. In addition, the on-board environment requires real time processing with limited computing resources, thus the algorithms must use fixed and relatively small amounts of processing time and memory. The University of Alabama in Huntsville is developing an innovative processing framework for the on-board data and information environment. The Environment for On-Board Processing (EVE) and the Adaptive On-board Data Processing (AODP) projects serve as proofs-of-concept of advanced information systems for remote sensing platforms. The EVE real-time processing infrastructure will upload, schedule and control the execution of processing plans on board remote sensors. These plans

  6. Editorial: "Business process intelligence : connecting data and processes"

    NARCIS (Netherlands)

    Aalst, van der W.M.P.; Zhao, J.L.; Wang, H.; Wang, Harry Jiannan

    2015-01-01

    This introduction to the special issue on Business Process Intelligence (BPI) discusses the relation between data and processes. The recent attention for Big Data illustrates that organizations are aware of the potential of the torrents of data generated by today's information systems. However, at

  7. On-board Data Mining

    Science.gov (United States)

    Tanner, Steve; Stein, Cara; Graves, Sara J.

    Networks of remote sensors are becoming more common as technology improves and costs decline. In the past, a remote sensor was usually a device that collected data to be retrieved at a later time by some other mechanism. This collected data were usually processed well after the fact at a computer greatly removed from the in situ sensing location. This has begun to change as sensor technology, on-board processing, and network communication capabilities have increased and their prices have dropped. There has been an explosion in the number of sensors and sensing devices, not just around the world, but literally throughout the solar system. These sensors are not only becoming vastly more sophisticated, accurate, and detailed in the data they gather but they are also becoming cheaper, lighter, and smaller. At the same time, engineers have developed improved methods to embed computing systems, memory, storage, and communication capabilities into the platforms that host these sensors. Now, it is not unusual to see large networks of sensors working in cooperation with one another. Nor does it seem strange to see the autonomous operation of sensorbased systems, from space-based satellites to smart vacuum cleaners that keep our homes clean and robotic toys that help to entertain and educate our children. But access to sensor data and computing power is only part of the story. For all the power of these systems, there are still substantial limits to what they can accomplish. These include the well-known limits to current Artificial Intelligence capabilities and our limited ability to program the abstract concepts, goals, and improvisation needed for fully autonomous systems. But it also includes much more basic engineering problems such as lack of adequate power, communications bandwidth, and memory, as well as problems with the geolocation and real-time georeferencing required to integrate data from multiple sensors to be used together.

  8. Intelligent systems for KSC ground processing

    Science.gov (United States)

    Heard, Astrid E.

    1992-01-01

    The ground processing and launch of Shuttle vehicles and their payloads is the primary task of Kennedy Space Center. It is a process which is largely manual and contains little inherent automation. Business is conducted today much as it was during previous NASA programs such as Apollo. In light of new programs and decreasing budgets, NASA must find more cost effective ways in which to do business while retaining the quality and safety of activities. Advanced technologies including artificial intelligence could cut manpower and processing time. This paper is an overview of the research and development in Al technology at KSC with descriptions of the systems which have been implemented, as well as a few under development which are promising additions to ground processing software. Projects discussed cover many facets of ground processing activities, including computer sustaining engineering, subsystem monitor and diagnosis tools and launch team assistants. The deployed Al applications have proven an effectiveness which has helped to demonstrate the benefits of utilizing intelligent software in the ground processing task.

  9. Real-time context aware reasoning in on-board intelligent traffic systems: An Architecture for Ontology-based Reasoning using Finite State Machines

    NARCIS (Netherlands)

    Stoter, Arjan; Dalmolen, Simon; Drenth, Eduard; Cornelisse, Erik; Mulder, Wico

    2011-01-01

    In-vehicle information management is vital in intelligent traffic systems. In this paper we motivate an architecture for ontology-based context-aware reasoning for in-vehicle information management. An ontology is essential for system standardization and communication, and ontology-based reasoning

  10. Markov decision processes in artificial intelligence

    CERN Document Server

    Sigaud, Olivier

    2013-01-01

    Markov Decision Processes (MDPs) are a mathematical framework for modeling sequential decision problems under uncertainty as well as Reinforcement Learning problems. Written by experts in the field, this book provides a global view of current research using MDPs in Artificial Intelligence. It starts with an introductory presentation of the fundamental aspects of MDPs (planning in MDPs, Reinforcement Learning, Partially Observable MDPs, Markov games and the use of non-classical criteria). Then it presents more advanced research trends in the domain and gives some concrete examples using illustr

  11. Parallel processing for artificial intelligence 2

    CERN Document Server

    Kumar, V; Suttner, CB

    1994-01-01

    With the increasing availability of parallel machines and the raising of interest in large scale and real world applications, research on parallel processing for Artificial Intelligence (AI) is gaining greater importance in the computer science environment. Many applications have been implemented and delivered but the field is still considered to be in its infancy. This book assembles diverse aspects of research in the area, providing an overview of the current state of technology. It also aims to promote further growth across the discipline. Contributions have been grouped according to their

  12. The process of implementing Competitive Intelligence in a company

    Directory of Open Access Journals (Sweden)

    František Bartes

    2013-01-01

    Full Text Available It is a common occurrence in business practice that the management of a company, in an effort to jump-start the function of the Competitive Intelligence unit, makes a number of mistakes and errors. Yet it is not difficult to avoid these missteps and achieve the desired level of Competitive Intelligence activities in a purposeful and effective manner. The author believes that a resolution of this problem lies in his concept of Competitive Intelligence viewed as a system application discipline (like value analysis or value engineering, which is why he approaches the problem of actual implementation of Competitive Intelligence in a company by referring to standards ČSN EN 12 973 and ČSN EN 1325-2. The author then proposes his own procedure for implementing Competitive Intelligence in a company. He first describes the various ways of securing the Competitive Intelligence services. Depending on the manner of securing these services, it is necessary to choose the actual method of bringing Competitive Intelligence into the company. The author goes on to lists the essentials that every program of Competitive Intelligence implementation should have. The process of Competitive Intelligence implementation unfolds in three stages, those being: 1. Managerial preparation for the introduction of Competitive Intelligence. 2. Personnel-oriented and professional preparation for applying Competitive Intelligence. 3. Organizational preparation for the implementation and practice of Competitive Intelligence. In Discussion, the author points out the most common mistakes he encountered in practice when implementing the Competitive Intelligence function.

  13. Process mining : business intelligence software wordt eindelijk intelligent

    NARCIS (Netherlands)

    Aalst, van der W.M.P.

    2007-01-01

    Business Intelligence is een begrip dat verwijst naar software die gebruikt kan worden om gegevens over operationele bedrijfsprocessen te verzamelen en deze vervolgens te analyseren. Het doel van BI software is het verkrijgen van meer kennis en inzicht, welke gebruikt kunnen worden om processen

  14. Tool path strategy and cutting process monitoring in intelligent machining

    Science.gov (United States)

    Chen, Ming; Wang, Chengdong; An, Qinglong; Ming, Weiwei

    2018-06-01

    Intelligent machining is a current focus in advanced manufacturing technology, and is characterized by high accuracy and efficiency. A central technology of intelligent machining—the cutting process online monitoring and optimization—is urgently needed for mass production. In this research, the cutting process online monitoring and optimization in jet engine impeller machining, cranio-maxillofacial surgery, and hydraulic servo valve deburring are introduced as examples of intelligent machining. Results show that intelligent tool path optimization and cutting process online monitoring are efficient techniques for improving the efficiency, quality, and reliability of machining.

  15. Artificial intelligence in the materials processing laboratory

    Science.gov (United States)

    Workman, Gary L.; Kaukler, William F.

    1990-01-01

    Materials science and engineering provides a vast arena for applications of artificial intelligence. Advanced materials research is an area in which challenging requirements confront the researcher, from the drawing board through production and into service. Advanced techniques results in the development of new materials for specialized applications. Hand-in-hand with these new materials are also requirements for state-of-the-art inspection methods to determine the integrity or fitness for service of structures fabricated from these materials. Two problems of current interest to the Materials Processing Laboratory at UAH are an expert system to assist in eddy current inspection of graphite epoxy components for aerospace and an expert system to assist in the design of superalloys for high temperature applications. Each project requires a different approach to reach the defined goals. Results to date are described for the eddy current analysis, but only the original concepts and approaches considered are given for the expert system to design superalloys.

  16. Damage localization using a power-efficient distributed on-board signal processing algorithm in a wireless sensor network

    International Nuclear Information System (INIS)

    Liu, Lei; Liu, Shuntao; Yuan, Fuh-Gwo

    2012-01-01

    A distributed on-board algorithm that is embedded and executed within a group of wireless sensors to locate structural damages in isotropic plates is presented. The algorithm is based on an energy-decay model of Lamb waves and singular value decomposition (SVD) to determine damage locations. A sensor group consists of a small number of sensors, each of which independently collects wave signals and evaluates wave energy upon an external triggering signal sent from a base station. The energy values, usually a few bytes in length, are then sent to the base station to determine the presence and location of damages. In comparison with traditional centralized approaches in which whole datasets are required to be transmitted, the proposed algorithm yields much less wireless communication traffic, yet with a modest amount of computation required within sensors. Experiments have shown that the algorithm is robust to locate damage for isotropic plate structures and is very power efficient, with more than an order-of-magnitude power saving

  17. High-flux MFI-alumina hollow fibres: a membrane-based process for on-board CO2 capture from internal combustion vehicles

    International Nuclear Information System (INIS)

    Nicolas, C.H.

    2011-01-01

    This work focuses on the conception and development of a membrane-based process for an on-board CO 2 capture/storage application. In a first part, we simulate an on-board CO 2 capture unit based on a membrane process for the case study of a heavy vehicle (≥3500 kg). This study includes an energy analysis of the impact of gas separation and compression on the required membrane surface and module volume, as well the autonomy of the storage unit and the energy overconsumption involved in the process. In a second part, we study the influence of the hollow-fibre support quality on the final intergrowth level of nano-composite MFI-alumina membranes. Special attention is devoted to the influence of the isomorphic substitution of silica by boron and germanium, and replacement of the counter-cation (proton) by other elements, on the CO 2 /N 2 separation and permeance properties. Next, a complete chapter has been devoted to the evaluation of the thermodynamic (adsorption) and kinetic (diffusion) parameters in the CO 2 /N 2 separation. Finally, we analyze the influence of standard pollutants (water, NO x , hydrocarbons) on the CO 2 separation properties of the synthesized membranes. (author)

  18. INTELLIGENT SUPPORT OF EDUCATIONAL PROCESSES AT LEVEL OF SPECIALITY

    Directory of Open Access Journals (Sweden)

    Irina I. Kazmina

    2013-01-01

    Full Text Available The article is devoted to intelligent support of educational processes at level of speciality with the help of information system. In this paper intelligent information system of Modern Humanitarian Academy is considered and three directions of development of intelligent support within the scope of developed information system are offered. These directions include: development of model of student, data mining of quality of teaching and prediction of quality of teaching in the future. 

  19. Using artificial intelligence to automate remittance processing.

    Science.gov (United States)

    Adams, W T; Snow, G M; Helmick, P M

    1998-06-01

    The consolidated business office of the Allegheny Health Education Research Foundation (AHERF), a large integrated healthcare system based in Pittsburgh, Pennsylvania, sought to improve its cash-related business office activities by implementing an automated remittance processing system that uses artificial intelligence. The goal was to create a completely automated system whereby all monies it processed would be tracked, automatically posted, analyzed, monitored, controlled, and reconciled through a central database. Using a phased approach, the automated payment system has become the central repository for all of the remittances for seven of the hospitals in the AHERF system and has allowed for the complete integration of these hospitals' existing billing systems, document imaging system, and intranet, as well as the new automated payment posting, and electronic cash tracking and reconciling systems. For such new technology, which is designed to bring about major change, factors contributing to the project's success were adequate planning, clearly articulated objectives, marketing, end-user acceptance, and post-implementation plan revision.

  20. Magnetic field on board

    International Nuclear Information System (INIS)

    Estevez Radio, H.; Fernandez Arenal, C.A.

    1995-01-01

    Here, the calculation of the magnetic field on board ships is performed, using matrix calculus, in a similar way as when the magnetic field in matter is studied. Thus the final formulas are written in a more compact form and they are obtained through a simpler way, more suitable for the university education. (Author)

  1. Internet-based intelligent information processing systems

    CERN Document Server

    Tonfoni, G; Ichalkaranje, N S

    2003-01-01

    The Internet/WWW has made it possible to easily access quantities of information never available before. However, both the amount of information and the variation in quality pose obstacles to the efficient use of the medium. Artificial intelligence techniques can be useful tools in this context. Intelligent systems can be applied to searching the Internet and data-mining, interpreting Internet-derived material, the human-Web interface, remote condition monitoring and many other areas. This volume presents the latest research on the interaction between intelligent systems (neural networks, adap

  2. On Intelligent Design and Planning Method of Process Route Based on Gun Breech Machining Process

    Science.gov (United States)

    Hongzhi, Zhao; Jian, Zhang

    2018-03-01

    The paper states an approach of intelligent design and planning of process route based on gun breech machining process, against several problems, such as complex machining process of gun breech, tedious route design and long period of its traditional unmanageable process route. Based on gun breech machining process, intelligent design and planning system of process route are developed by virtue of DEST and VC++. The system includes two functional modules--process route intelligent design and its planning. The process route intelligent design module, through the analysis of gun breech machining process, summarizes breech process knowledge so as to complete the design of knowledge base and inference engine. And then gun breech process route intelligently output. On the basis of intelligent route design module, the final process route is made, edited and managed in the process route planning module.

  3. Predicting speech intelligibility in conditions with nonlinearly processed noisy speech

    DEFF Research Database (Denmark)

    Jørgensen, Søren; Dau, Torsten

    2013-01-01

    The speech-based envelope power spectrum model (sEPSM; [1]) was proposed in order to overcome the limitations of the classical speech transmission index (STI) and speech intelligibility index (SII). The sEPSM applies the signal-tonoise ratio in the envelope domain (SNRenv), which was demonstrated...... to successfully predict speech intelligibility in conditions with nonlinearly processed noisy speech, such as processing with spectral subtraction. Moreover, a multiresolution version (mr-sEPSM) was demonstrated to account for speech intelligibility in various conditions with stationary and fluctuating...

  4. Intelligent Transportation Control based on Proactive Complex Event Processing

    Directory of Open Access Journals (Sweden)

    Wang Yongheng

    2016-01-01

    Full Text Available Complex Event Processing (CEP has become the key part of Internet of Things (IoT. Proactive CEP can predict future system states and execute some actions to avoid unwanted states which brings new hope to intelligent transportation control. In this paper, we propose a proactive CEP architecture and method for intelligent transportation control. Based on basic CEP technology and predictive analytic technology, a networked distributed Markov decision processes model with predicting states is proposed as sequential decision model. A Q-learning method is proposed for this model. The experimental evaluations show that this method works well when used to control congestion in in intelligent transportation systems.

  5. Multiple multichannel spectra acquisition and processing system with intelligent interface

    International Nuclear Information System (INIS)

    Chen Ying; Wei Yixiang; Qu Jianshi; Zheng Futang; Xu Shengkui; Xie Yuanming; Qu Xing; Ji Weitong; Qiu Xuehua

    1986-01-01

    A Multiple multichannel spectra acquisition and processing system with intelligent interface is described. Sixteen spectra measured with various lengths, channel widths, back biases and acquisition times can be identified and collected by the intelligent interface simultaneously while the connected computer is doing data processing. The execution time for the Ge(Li) gamma-ray spectrum analysis software on IBM PC-XT is about 55 seconds

  6. Intelligent Transportation Control based on Proactive Complex Event Processing

    OpenAIRE

    Wang Yongheng; Geng Shaofeng; Li Qian

    2016-01-01

    Complex Event Processing (CEP) has become the key part of Internet of Things (IoT). Proactive CEP can predict future system states and execute some actions to avoid unwanted states which brings new hope to intelligent transportation control. In this paper, we propose a proactive CEP architecture and method for intelligent transportation control. Based on basic CEP technology and predictive analytic technology, a networked distributed Markov decision processes model with predicting states is p...

  7. The big data processing platform for intelligent agriculture

    Science.gov (United States)

    Huang, Jintao; Zhang, Lichen

    2017-08-01

    Big data technology is another popular technology after the Internet of Things and cloud computing. Big data is widely used in many fields such as social platform, e-commerce, and financial analysis and so on. Intelligent agriculture in the course of the operation will produce large amounts of data of complex structure, fully mining the value of these data for the development of agriculture will be very meaningful. This paper proposes an intelligent data processing platform based on Storm and Cassandra to realize the storage and management of big data of intelligent agriculture.

  8. Sustainability Reporting Process Model using Business Intelligence

    OpenAIRE

    Alxneit, Thorsten Julius

    2015-01-01

    Sustainability including the reporting requirements is one of the most relevant topics for companies. In recent years, many software providers have launched new software tools targeting companies committed to implementing sustainability reporting. But it’s not only companies willing to use their Business Intelligence (BI) solution, there are also basic principles such as the single source of truth and tendencies to combine sustainability reporting with the financial reporting (...

  9. An Approach to quantify the Costs of Business Process Intelligence.

    NARCIS (Netherlands)

    Mutschler, B.B.; Bumiller, J.; Reichert, M.U.; Desel, J.; Frank, U.

    2005-01-01

    Today, enterprises are forced to continuously optimize their business as well as service processes. In this context the process-centered alignment of information systems is crucial. The use of business process intelligence (BPI) tools offers promising perspectives in this respect. However, when

  10. Artificial intelligence in process design and operation

    International Nuclear Information System (INIS)

    Sudduth, A.L.

    1988-01-01

    Artificial Intelligence (AI) has recently become prominent in the discussion of computer applications in the utility business. In order to assess this technology, a research project was performed to determine whether software development techniques based on AI could be used to facilitate management of information associated with the design of a generating station. The approach taken was the development of an expert system, using a relatively simple set of rules acting on a more complex knowledge base. A successful prototype for the application was developed and its potential extension to a production environment demonstrated. During the course of prototype development, other possible applications of AI in design engineering were discovered, and areas of particular interest selected for further investigation. A plan for AI R and D was formulated. That plan and other possible future work in AI are discussed

  11. Intelligent query processing for semantic mediation of information systems

    Directory of Open Access Journals (Sweden)

    Saber Benharzallah

    2011-11-01

    Full Text Available We propose an intelligent and an efficient query processing approach for semantic mediation of information systems. We propose also a generic multi agent architecture that supports our approach. Our approach focuses on the exploitation of intelligent agents for query reformulation and the use of a new technology for the semantic representation. The algorithm is self-adapted to the changes of the environment, offers a wide aptitude and solves the various data conflicts in a dynamic way; it also reformulates the query using the schema mediation method for the discovered systems and the context mediation for the other systems.

  12. Cognitive Process as a Basis for Intelligent Retrieval Systems Design.

    Science.gov (United States)

    Chen, Hsinchun; Dhar, Vasant

    1991-01-01

    Two studies of the cognitive processes involved in online document-based information retrieval were conducted. These studies led to the development of five computational models of online document retrieval which were incorporated into the design of an "intelligent" document-based retrieval system. Both the system and the broader implications of…

  13. Meaning of cognitive processes for creating artificial intelligence

    OpenAIRE

    Pangrác, Vojtěch

    2011-01-01

    This diploma thesis brings an integral view at cognitive processes connected with artificial intelligence systems, and makes a comparison with the processes observed in nature, including human being. A historical background helps us to look at the whole issue from a certain point of view. The main axis of interest comes after the historical overview and includes the following: environment -- stimulations -- processing -- reflection in the cognitive system -- reaction to stimulation; I balance...

  14. Intelligent control for scalable video processing

    NARCIS (Netherlands)

    Wüst, C.C.

    2006-01-01

    In this thesis we study a problem related to cost-effective video processing in software by consumer electronics devices, such as digital TVs. Video processing is the task of transforming an input video signal into an output video signal, for example to improve the quality of the signal. This

  15. Advances in Reasoning-Based Image Processing Intelligent Systems Conventional and Intelligent Paradigms

    CERN Document Server

    Nakamatsu, Kazumi

    2012-01-01

    The book puts special stress on the contemporary techniques for reasoning-based image processing and analysis: learning based image representation and advanced video coding; intelligent image processing and analysis in medical vision systems; similarity learning models for image reconstruction; visual perception for mobile robot motion control, simulation of human brain activity in the analysis of video sequences; shape-based invariant features extraction; essential of paraconsistent neural networks, creativity and intelligent representation in computational systems. The book comprises 14 chapters. Each chapter is a small monograph, representing resent investigations of authors in the area. The topics of the chapters cover wide scientific and application areas and complement each-other very well. The chapters’ content is based on fundamental theoretical presentations, followed by experimental results and comparison with similar techniques. The size of the chapters is well-ballanced which permits a thorough ...

  16. Intelligent Controller Design for a Chemical Process

    OpenAIRE

    Mr. Glan Devadhas G; Dr.Pushpakumar S.

    2010-01-01

    Chemical process control is a challenging problem due to the strong on*line non*linearity and extreme sensitivity to disturbances of the process. Ziegler – Nichols tuned PI and PID controllers are found to provide poor performances for higher*order and non–linear systems. This paper presents an application of one*step*ahead fuzzy as well as ANFIS (adaptive*network*based fuzzy inference system) tuning scheme for an Continuous Stirred Tank Reactor CSTR process. The controller is designed based ...

  17. Towards a universal competitive intelligence process model

    Directory of Open Access Journals (Sweden)

    Rene Pellissier

    2013-08-01

    Objectives: The purpose of this research is to review the current literature on CI, to look at the aims of identifying and analysing CI process models, and finally to propose a universal CI process model. Method: The study was qualitative in nature and content analysis was conducted on all identified sources establishing and analysing CI process models. To identify relevant literature, academic databases and search engines were used. Moreover, a review of references in related studies led to more relevant sources, the references of which were further reviewed and analysed. To ensure reliability, only peer-reviewed articles were used. Results: The findings reveal that the majority of scholars view the CI process as a cycle of interrelated phases. The output of one phase is the input of the next phase. Conclusion: The CI process is a cycle of interrelated phases. The output of one phase is the input of the next phase. These phases are influenced by the following factors: decision makers, process and structure, organisational awareness and culture, and feedback.

  18. The Role of Intelligence Quotient and Emotional Intelligence in Cognitive Control Processes

    Science.gov (United States)

    Checa, Purificación; Fernández-Berrocal, Pablo

    2015-01-01

    The relationship between intelligence quotient (IQ) and cognitive control processes has been extensively established. Several studies have shown that IQ correlates with cognitive control abilities, such as interference suppression, as measured with experimental tasks like the Stroop and Flanker tasks. By contrast, there is a debate about the role of Emotional Intelligence (EI) in individuals' cognitive control abilities. The aim of this study is to examine the relation between IQ and EI, and cognitive control abilities evaluated by a typical laboratory control cognitive task, the Stroop task. Results show a negative correlation between IQ and the interference suppression index, the ability to inhibit processing of irrelevant information. However, the Managing Emotions dimension of EI measured by the Mayer-Salovey-Caruso Emotional Intelligence Test (MSCEIT), but not self-reported of EI, negatively correlates with the impulsivity index, the premature execution of the response. These results suggest that not only is IQ crucial, but also competences related to EI are essential to human cognitive control processes. Limitations and implications of these results are also discussed. PMID:26648901

  19. The role of Intelligence Quotient and Emotional Intelligence in cognitive control processes

    Directory of Open Access Journals (Sweden)

    Purificación eCheca

    2015-12-01

    Full Text Available The relationship between intelligence quotient (IQ and cognitive control processes has been extensively established. Several studies have shown that IQ correlates with cognitive control abilities, such as interference suppression, as measured with experimental tasks like the Stroop and Flanker tasks. By contrast, there is a debate about the role of Emotional Intelligence (EI in individuals’ cognitive control abilities. The aim of this study is to examine the relation between IQ and EI, and cognitive control abilities evaluated by a typical laboratory control cognitive task, the Stroop task. Results show a negative correlation between IQ and the interference suppression index, the ability to inhibit processing of irrelevant information. However, the Managing Emotions dimension of EI measured by the Mayer-Salovey-Caruso Emotional Intelligence Test, but not self-reported of EI, negatively correlates with the impulsivity index, the premature execution of the response. These results suggest that not only is IQ crucial, but also competences related to EI are essential to human cognitive control processes. Limitations and implications of these results are also discussed

  20. Matching intelligent systems with business process reengineering

    NARCIS (Netherlands)

    Hart, 't M.W.

    1996-01-01

    According to Venkatraman (1991) five degrees of IT-induced business reconfiguration can be distinguished: (1) localized exploitation of IT, (2) internal integration, (3) business process redesign, (4) business network redesign, and (5) business scope redefinition. On each of these levels, different

  1. Intelligent Predictive Control of Nonlienar Processes Using

    DEFF Research Database (Denmark)

    Nørgård, Peter Magnus; Sørensen, Paul Haase; Poulsen, Niels Kjølstad

    1996-01-01

    This paper presents a novel approach to design of generalized predictive controllers (GPC) for nonlinear processes. A neural network is used for modelling the process and a gain-scheduling type of GPC is subsequently designed. The combination of neural network models and predictive control has...... frequently been discussed in the neural network community. This paper proposes an approximate scheme, the approximate predictive control (APC), which facilitates the implementation and gives a substantial reduction in the required amount of computations. The method is based on a technique for extracting...... linear models from a nonlinear neural network and using them in designing the control system. The performance of the controller is demonstrated in a simulation study of a pneumatic servo system...

  2. Building the competitive intelligence knowledge: processes and activities in a corporate organisation

    OpenAIRE

    Sreenivasulu, V.

    1999-01-01

    This paper discusses the process of building and developing comprehensive tools, techniques, support systems, and better methods of harnessing the competitive intelligence knowledge processes. The author stresses the need for building sophisticated methodological competitive intelligence knowledge acquisition, systematic collection of competitive intelligence knowledge from various sources for critical analysis, process, organization, synthesis, assessment, screening, filtering and interpreta...

  3. A conceptual framework for intelligent real-time information processing

    Science.gov (United States)

    Schudy, Robert

    1987-01-01

    By combining artificial intelligence concepts with the human information processing model of Rasmussen, a conceptual framework was developed for real time artificial intelligence systems which provides a foundation for system organization, control and validation. The approach is based on the description of system processing terms of an abstraction hierarchy of states of knowledge. The states of knowledge are organized along one dimension which corresponds to the extent to which the concepts are expressed in terms of the system inouts or in terms of the system response. Thus organized, the useful states form a generally triangular shape with the sensors and effectors forming the lower two vertices and the full evaluated set of courses of action the apex. Within the triangle boundaries are numerous processing paths which shortcut the detailed processing, by connecting incomplete levels of analysis to partially defined responses. Shortcuts at different levels of abstraction include reflexes, sensory motor control, rule based behavior, and satisficing. This approach was used in the design of a real time tactical decision aiding system, and in defining an intelligent aiding system for transport pilots.

  4. An intelligent allocation algorithm for parallel processing

    Science.gov (United States)

    Carroll, Chester C.; Homaifar, Abdollah; Ananthram, Kishan G.

    1988-01-01

    The problem of allocating nodes of a program graph to processors in a parallel processing architecture is considered. The algorithm is based on critical path analysis, some allocation heuristics, and the execution granularity of nodes in a program graph. These factors, and the structure of interprocessor communication network, influence the allocation. To achieve realistic estimations of the executive durations of allocations, the algorithm considers the fact that nodes in a program graph have to communicate through varying numbers of tokens. Coarse and fine granularities have been implemented, with interprocessor token-communication duration, varying from zero up to values comparable to the execution durations of individual nodes. The effect on allocation of communication network structures is demonstrated by performing allocations for crossbar (non-blocking) and star (blocking) networks. The algorithm assumes the availability of as many processors as it needs for the optimal allocation of any program graph. Hence, the focus of allocation has been on varying token-communication durations rather than varying the number of processors. The algorithm always utilizes as many processors as necessary for the optimal allocation of any program graph, depending upon granularity and characteristics of the interprocessor communication network.

  5. Intelligent Adaptation Process for Case Based Systems

    International Nuclear Information System (INIS)

    Nassar, A.M.; Mohamed, A.H.; Mohamed, A.H.

    2014-01-01

    Case Based Reasoning (CBR) Systems is one of the important decision making systems applied in many fields all over the world. The effectiveness of any CBR system based on the quality of the storage cases in the case library. Similar cases can be retrieved and adapted to produce the solution for the new problem. One of the main issues faced the CBR systems is the difficulties of achieving the useful cases. The proposed system introduces a new approach that uses the genetic algorithm (GA) technique to automate constructing the cases into the case library. Also, it can optimize the best one to be stored in the library for the future uses. However, the proposed system can avoid the problems of the uncertain and noisy cases. Besides, it can simply the retrieving and adaptation processes. So, it can improve the performance of the CBR system. The suggested system can be applied for many real-time problems. It has been applied for diagnosis the faults of the wireless network, diagnosis of the cancer diseases, diagnosis of the debugging of a software as cases of study. The proposed system has proved its performance in this field

  6. Employing the intelligence cycle process model within the Homeland Security Enterprise

    OpenAIRE

    Stokes, Roger L.

    2013-01-01

    CHDS State/Local The purpose of this thesis was to examine the employment and adherence of the intelligence cycle process model within the National Network of Fusion Centers and the greater Homeland Security Enterprise by exploring the customary intelligence cycle process model established by the United States Intelligence Community (USIC). This thesis revealed there are various intelligence cycle process models used by the USIC and taught to the National Network. Given the numerous differ...

  7. Artificial intelligence, expert systems, computer vision, and natural language processing

    Science.gov (United States)

    Gevarter, W. B.

    1984-01-01

    An overview of artificial intelligence (AI), its core ingredients, and its applications is presented. The knowledge representation, logic, problem solving approaches, languages, and computers pertaining to AI are examined, and the state of the art in AI is reviewed. The use of AI in expert systems, computer vision, natural language processing, speech recognition and understanding, speech synthesis, problem solving, and planning is examined. Basic AI topics, including automation, search-oriented problem solving, knowledge representation, and computational logic, are discussed.

  8. Working memory and intelligibility of hearing-aid processed speech

    Science.gov (United States)

    Souza, Pamela E.; Arehart, Kathryn H.; Shen, Jing; Anderson, Melinda; Kates, James M.

    2015-01-01

    Previous work suggested that individuals with low working memory capacity may be at a disadvantage in adverse listening environments, including situations with background noise or substantial modification of the acoustic signal. This study explored the relationship between patient factors (including working memory capacity) and intelligibility and quality of modified speech for older individuals with sensorineural hearing loss. The modification was created using a combination of hearing aid processing [wide-dynamic range compression (WDRC) and frequency compression (FC)] applied to sentences in multitalker babble. The extent of signal modification was quantified via an envelope fidelity index. We also explored the contribution of components of working memory by including measures of processing speed and executive function. We hypothesized that listeners with low working memory capacity would perform more poorly than those with high working memory capacity across all situations, and would also be differentially affected by high amounts of signal modification. Results showed a significant effect of working memory capacity for speech intelligibility, and an interaction between working memory, amount of hearing loss and signal modification. Signal modification was the major predictor of quality ratings. These data add to the literature on hearing-aid processing and working memory by suggesting that the working memory-intelligibility effects may be related to aggregate signal fidelity, rather than to the specific signal manipulation. They also suggest that for individuals with low working memory capacity, sensorineural loss may be most appropriately addressed with WDRC and/or FC parameters that maintain the fidelity of the signal envelope. PMID:25999874

  9. Advanced multiresponse process optimisation an intelligent and integrated approach

    CERN Document Server

    Šibalija, Tatjana V

    2016-01-01

    This book presents an intelligent, integrated, problem-independent method for multiresponse process optimization. In contrast to traditional approaches, the idea of this method is to provide a unique model for the optimization of various processes, without imposition of assumptions relating to the type of process, the type and number of process parameters and responses, or interdependences among them. The presented method for experimental design of processes with multiple correlated responses is composed of three modules: an expert system that selects the experimental plan based on the orthogonal arrays; the factor effects approach, which performs processing of experimental data based on Taguchi’s quality loss function and multivariate statistical methods; and process modeling and optimization based on artificial neural networks and metaheuristic optimization algorithms. The implementation is demonstrated using four case studies relating to high-tech industries and advanced, non-conventional processes.

  10. [INVITED] Computational intelligence for smart laser materials processing

    Science.gov (United States)

    Casalino, Giuseppe

    2018-03-01

    Computational intelligence (CI) involves using a computer algorithm to capture hidden knowledge from data and to use them for training ;intelligent machine; to make complex decisions without human intervention. As simulation is becoming more prevalent from design and planning to manufacturing and operations, laser material processing can also benefit from computer generating knowledge through soft computing. This work is a review of the state-of-the-art on the methodology and applications of CI in laser materials processing (LMP), which is nowadays receiving increasing interest from world class manufacturers and 4.0 industry. The focus is on the methods that have been proven effective and robust in solving several problems in welding, cutting, drilling, surface treating and additive manufacturing using the laser beam. After a basic description of the most common computational intelligences employed in manufacturing, four sections, namely, laser joining, machining, surface, and additive covered the most recent applications in the already extensive literature regarding the CI in LMP. Eventually, emerging trends and future challenges were identified and discussed.

  11. Artificial intelligence implementation in the APS process diagnostic

    Energy Technology Data Exchange (ETDEWEB)

    Guessasma, Sofiane; Salhi, Zahir; Montavon, Ghislain; Gougeon, Patrick; Coddet, Christian

    2004-07-25

    Thermal spray process is a technique of coating manufacturing implementing a wide variety of materials and processes. This technique is characterized by up to 150 processing parameters influencing the coating properties. The control of the coating quality is needed through the consideration of a robust methodology that takes into account the parameter interdependencies, the process variability and offers the ability to quantify the processing parameter-process response relationships. The aim of this work is to introduce a new approach based on artificial intelligence responding to these requirements. A detailed procedure is presented considering an artificial neural network (ANN) structure which encodes implicitly the physical phenomena governing the process. The implementation of such a structure was coupled to experimental results of an optic sensor controlling the powder particle fusion state before the coating formation. The optimization steps were discussed and the predicted results were compared to the experimental ones allowing the identification of the control factors.

  12. Artificial intelligence implementation in the APS process diagnostic

    International Nuclear Information System (INIS)

    Guessasma, Sofiane; Salhi, Zahir; Montavon, Ghislain; Gougeon, Patrick; Coddet, Christian

    2004-01-01

    Thermal spray process is a technique of coating manufacturing implementing a wide variety of materials and processes. This technique is characterized by up to 150 processing parameters influencing the coating properties. The control of the coating quality is needed through the consideration of a robust methodology that takes into account the parameter interdependencies, the process variability and offers the ability to quantify the processing parameter-process response relationships. The aim of this work is to introduce a new approach based on artificial intelligence responding to these requirements. A detailed procedure is presented considering an artificial neural network (ANN) structure which encodes implicitly the physical phenomena governing the process. The implementation of such a structure was coupled to experimental results of an optic sensor controlling the powder particle fusion state before the coating formation. The optimization steps were discussed and the predicted results were compared to the experimental ones allowing the identification of the control factors

  13. Natural language processing in psychiatry. Artificial intelligence technology and psychopathology.

    Science.gov (United States)

    Garfield, D A; Rapp, C; Evens, M

    1992-04-01

    The potential benefit of artificial intelligence (AI) technology as a tool of psychiatry has not been well defined. In this essay, the technology of natural language processing and its position with regard to the two main schools of AI is clearly outlined. Past experiments utilizing AI techniques in understanding psychopathology are reviewed. Natural language processing can automate the analysis of transcripts and can be used in modeling theories of language comprehension. In these ways, it can serve as a tool in testing psychological theories of psychopathology and can be used as an effective tool in empirical research on verbal behavior in psychopathology.

  14. Ramp Technology and Intelligent Processing in Small Manufacturing

    Science.gov (United States)

    Rentz, Richard E.

    1992-01-01

    To address the issues of excessive inventories and increasing procurement lead times, the Navy is actively pursuing flexible computer integrated manufacturing (FCIM) technologies, integrated by communication networks to respond rapidly to its requirements for parts. The Rapid Acquisition of Manufactured Parts (RAMP) program, initiated in 1986, is an integral part of this effort. The RAMP program's goal is to reduce the current average production lead times experienced by the Navy's inventory control points by a factor of 90 percent. The manufacturing engineering component of the RAMP architecture utilizes an intelligent processing technology built around a knowledge-based shell provided by ICAD, Inc. Rules and data bases in the software simulate an expert manufacturing planner's knowledge of shop processes and equipment. This expert system can use Product Data Exchange using STEP (PDES) data to determine what features the required part has, what material is required to manufacture it, what machines and tools are needed, and how the part should be held (fixtured) for machining, among other factors. The program's rule base then indicates, for example, how to make each feature, in what order to make it, and to which machines on the shop floor the part should be routed for processing. This information becomes part of the shop work order. The process planning function under RAMP greatly reduces the time and effort required to complete a process plan. Since the PDES file that drives the intelligent processing is 100 percent complete and accurate to start with, the potential for costly errors is greatly diminished.

  15. The Relationship between Multiple Intelligences with Preferred Science Teaching and Science Process Skills

    Directory of Open Access Journals (Sweden)

    Mohd Ali Samsudin

    2015-02-01

    Full Text Available This study was undertaken to identify the relationship between multiple intelligences with preferred science teaching and science process skills. The design of the study is a survey using three questionnaires reported in the literature: Multiple Intelligences Questionnaire, Preferred Science Teaching Questionnaire and Science Process Skills Questionnaire. The study selected 300 primary school students from five (5 primary schools in Penang, Malaysia. The findings showed a relationship between kinesthetic, logical-mathematical, visual-spatial and naturalistic intelligences with the preferred science teaching. In addition there was a correlation between kinesthetic and visual-spatial intelligences with science process skills, implying that multiple intelligences are related to science learning.

  16. The ethical intelligence: a tool guidance in the process of the negotiation

    Directory of Open Access Journals (Sweden)

    Cristina Seijo

    2014-08-01

    Full Text Available The present article is the result of a research, which has as object present a theoretical contrast that invites to the reflection on the ethical intelligence as a tool guidance in the negotiation. In the same one there are approached the different types of ethical intelligence; spatial intelligence, rational intelligence, emotional intelligence among others, equally one refers associative intelligence to the processes of negotiation and to the tactics of negotiation. In this respect, it is possible to deal to the ethical intelligence as the aptitude to examine the moral standards of the individual and of the society to decide between what this one correct or incorrect and to be able like that to solve the different problematic ones for which an individual or a society cross. For this reason, one invites to start mechanisms of transparency and participation by virtue of which the ethical intelligence is born in mind as the threshold that orientates this process of negotiation. 

  17. New On-board Microprocessors

    Science.gov (United States)

    Weigand, R.

    Two new processor devices have been developed for the use on board of spacecrafts. An 8-bit 8032-microcontroller targets typical controlling applications in instruments and sub-systems, or could be used as a main processor on small satellites, whereas the LEON 32-bit SPARC processor can be used for high performance controlling and data processing tasks. The ADV80S32 is fully compliant to the Intel 80x1 architecture and instruction set, extended by additional peripherals, 512 bytes on-chip RAM and a bootstrap PROM, which allows downloading the application software using the CCSDS PacketWire pro- tocol. The memory controller provides a de-multiplexed address/data bus, and allows to access up to 16 MB data and 8 MB program RAM. The peripherals have been de- signed for the specific needs of a spacecraft, such as serial interfaces compatible to RS232, PacketWire and TTC-B-01, counters/timers for extended duration and a CRC calculation unit accelerating the CCSDS TM/TC protocol. The 0.5 um Atmel manu- facturing technology (MG2RT) provides latch-up and total dose immunity; SEU fault immunity is implemented by using SEU hardened Flip-Flops and EDAC protection of internal and external memories. The maximum clock frequency of 20 MHz allows a processing power of 3 MIPS. Engineering samples are available. For SW develop- ment, various SW packages for the 8051 architecture are on the market. The LEON processor implements a 32-bit SPARC V8 architecture, including all the multiply and divide instructions, complemented by a floating-point unit (FPU). It includes several standard peripherals, such as timers/watchdog, interrupt controller, UARTs, parallel I/Os and a memory controller, allowing to use 8, 16 and 32 bit PROM, SRAM or memory mapped I/O. With on-chip separate instruction and data caches, almost one instruction per clock cycle can be reached in some applications. A 33-MHz 32-bit PCI master/target interface and a PCI arbiter allow operating the device in a plug-in card

  18. Working memory and intelligibility of hearing-aid processed speech

    Directory of Open Access Journals (Sweden)

    Pamela eSouza

    2015-05-01

    Full Text Available Previous work suggested that individuals with low working memory capacity may be at a disadvantage in adverse listening environments, including situations with background noise or substantial modification of the acoustic signal. This study explored the relationship between patient factors (including working memory capacity and intelligibility and quality of modified speech for older individuals with sensorineural hearing loss. The modification was created using a combination of hearing aid processing (wide-dynamic range compression and frequency compression applied to sentences in multitalker babble. The extent of signal modification was quantified via an envelope fidelity index. We also explored the contribution of components of working memory by including measures of processing speed and executive function. We hypothesized that listeners with low working memory capacity would perform more poorly than those with high working memory capacity across all situations, and would also be differentially affected by high amounts of signal modification. Results showed a significant effect of working memory capacity for speech intelligibility, and an interaction between working memory, amount of hearing loss and signal modification. Signal modification was the major predictor of quality ratings. These data add to the literature on hearing-aid processing and working memory by suggesting that the working memory-intelligibility effects may be related to aggregate signal fidelity, rather than on the specific signal manipulation. They also suggest that for individuals with low working memory capacity, sensorineural loss may be most appropriately addressed with wide-dynamic range compression and/or frequency compression parameters that maintain the fidelity of the signal envelope.

  19. Adaptive Moving Object Tracking Integrating Neural Networks And Intelligent Processing

    Science.gov (United States)

    Lee, James S. J.; Nguyen, Dziem D.; Lin, C.

    1989-03-01

    A real-time adaptive scheme is introduced to detect and track moving objects under noisy, dynamic conditions including moving sensors. This approach integrates the adaptiveness and incremental learning characteristics of neural networks with intelligent reasoning and process control. Spatiotemporal filtering is used to detect and analyze motion, exploiting the speed and accuracy of multiresolution processing. A neural network algorithm constitutes the basic computational structure for classification. A recognition and learning controller guides the on-line training of the network, and invokes pattern recognition to determine processing parameters dynamically and to verify detection results. A tracking controller acts as the central control unit, so that tracking goals direct the over-all system. Performance is benchmarked against the Widrow-Hoff algorithm, for target detection scenarios presented in diverse FLIR image sequences. Efficient algorithm design ensures that this recognition and control scheme, implemented in software and commercially available image processing hardware, meets the real-time requirements of tracking applications.

  20. Intelligence

    Science.gov (United States)

    Sternberg, Robert J.

    2012-01-01

    Intelligence is the ability to learn from experience and to adapt to, shape, and select environments. Intelligence as measured by (raw scores on) conventional standardized tests varies across the lifespan, and also across generations. Intelligence can be understood in part in terms of the biology of the brain—especially with regard to the functioning in the prefrontal cortex—and also correlates with brain size, at least within humans. Studies of the effects of genes and environment suggest that the heritability coefficient (ratio of genetic to phenotypic variation) is between .4 and .8, although heritability varies as a function of socioeconomic status and other factors. Racial differences in measured intelligence have been observed, but race is a socially constructed rather than biological variable, so such differences are difficult to interpret. PMID:22577301

  1. Intelligence.

    Science.gov (United States)

    Sternberg, Robert J

    2012-03-01

    Intelligence is the ability to learn from experience and to adapt to, shape, and select environments. Intelligence as measured by (raw scores on) conventional standardized tests varies across the lifespan, and also across generations. Intelligence can be understood in part in terms of the biology of the brain-especially with regard to the functioning in the prefrontal cortex-and also correlates with brain size, at least within humans. Studies of the effects of genes and environment suggest that the heritability coefficient (ratio of genetic to phenotypic variation) is between .4 and .8, although heritability varies as a function of socioeconomic status and other factors. Racial differences in measured intelligence have been observed, but race is a socially constructed rather than biological variable, so such differences are difficult to interpret.

  2. The AGILE on-board Kalman filter

    International Nuclear Information System (INIS)

    Giuliani, A.; Cocco, V.; Mereghetti, S.; Pittori, C.; Tavani, M.

    2006-01-01

    On-board reduction of particle background is one of the main challenges of space instruments dedicated to gamma-ray astrophysics. We present in this paper a discussion of the method and main simulation results of the on-board background filter of the Gamma-Ray Imaging Detector (GRID) of the AGILE mission. The GRID is capable of detecting and imaging with optimal point spread function gamma-ray photons in the range 30MeV-30GeV. The AGILE planned orbit is equatorial, with an altitude of 550km. This is an optimal orbit from the point of view of the expected particle background. For this orbit, electrons and positrons of kinetic energies between 20MeV and hundreds of MeV dominate the particle background, with significant contributions from high-energy (primary) and low-energy protons, and gamma-ray albedo-photons. We present here the main results obtained by extensive simulations of the on-board AGILE-GRID particle/photon background rejection algorithms based on a special application of Kalman filter techniques. This filter is applied (Level-2) sequentially after other data processing techniques characterizing the Level-1 processing. We show that, in conjunction with the Level-1 processing, the adopted Kalman filtering is expected to reduce the total particle/albedo-photon background rate to a value (=<10-30Hz) that is compatible with the AGILE telemetry. The AGILE on-board Kalman filter is also effective in reducing the Earth-albedo-photon background rate, and therefore contributes to substantially increase the AGILE exposure for celestial gamma-ray sources

  3. Acoustic richness modulates the neural networks supporting intelligible speech processing.

    Science.gov (United States)

    Lee, Yune-Sang; Min, Nam Eun; Wingfield, Arthur; Grossman, Murray; Peelle, Jonathan E

    2016-03-01

    The information contained in a sensory signal plays a critical role in determining what neural processes are engaged. Here we used interleaved silent steady-state (ISSS) functional magnetic resonance imaging (fMRI) to explore how human listeners cope with different degrees of acoustic richness during auditory sentence comprehension. Twenty-six healthy young adults underwent scanning while hearing sentences that varied in acoustic richness (high vs. low spectral detail) and syntactic complexity (subject-relative vs. object-relative center-embedded clause structures). We manipulated acoustic richness by presenting the stimuli as unprocessed full-spectrum speech, or noise-vocoded with 24 channels. Importantly, although the vocoded sentences were spectrally impoverished, all sentences were highly intelligible. These manipulations allowed us to test how intelligible speech processing was affected by orthogonal linguistic and acoustic demands. Acoustically rich speech showed stronger activation than acoustically less-detailed speech in a bilateral temporoparietal network with more pronounced activity in the right hemisphere. By contrast, listening to sentences with greater syntactic complexity resulted in increased activation of a left-lateralized network including left posterior lateral temporal cortex, left inferior frontal gyrus, and left dorsolateral prefrontal cortex. Significant interactions between acoustic richness and syntactic complexity occurred in left supramarginal gyrus, right superior temporal gyrus, and right inferior frontal gyrus, indicating that the regions recruited for syntactic challenge differed as a function of acoustic properties of the speech. Our findings suggest that the neural systems involved in speech perception are finely tuned to the type of information available, and that reducing the richness of the acoustic signal dramatically alters the brain's response to spoken language, even when intelligibility is high. Copyright © 2015 Elsevier

  4. ON-BOARD COMPUTER SYSTEM FOR KITSAT-1 AND 2

    Directory of Open Access Journals (Sweden)

    H. S. Kim

    1996-06-01

    Full Text Available KITSAT-1 and 2 are microsatellites weighting 50kg and all the on-board data are processed by the on-board computer system. Hence, these on-board computers require to be highly reliable and be designed with tight power consumption, mass and size constraints. On-board computer(OBC systems for KITSAT-1 and 2 are also designed with a simple flexible hardware for reliability and software takes more responsibility than hardware. KITSAT-1 and 2 on-board computer system consist of OBC 186 as the primary OBC and OBC80 as its backup. OBC186 runs spacecraft operating system (SCOS which has real-time multi-tasking capability. Since their launch, OBC186 and OBC80 have been operating successfully until today. In this paper, we describe the development of OBC186 hardware and software and analyze its in-orbit operation performance.

  5. USE OF ARTIFICIAL INTELLIGENCE TECHNIQUES IN QUALITY IMPROVING PROCESS

    OpenAIRE

    KALİTE İYİLEŞTİRME SÜRECİNDE YAPAY ZEKÃ KAYA; Orhan ENGİN

    2005-01-01

    Today, changing of competition conditions and customer preferences caused to happen many differences in the viewpoint of firms' quality studies. At the same time, improvements in computer technologies accelerated use of artificial intelligence. Artificial intelligence technologies are being used to solve many industry problems. In this paper, we investigated the use of artificial intelligence techniques to solve quality problems. The artificial intelligence techniques, which are used in quali...

  6. Automatic maintenance payload on board of a Mexican LEO microsatellite

    Science.gov (United States)

    Vicente-Vivas, Esaú; García-Nocetti, Fabián; Mendieta-Jiménez, Francisco

    2006-02-01

    Few research institutions from Mexico work together to finalize the integration of a technological demonstration microsatellite called Satex, aiming the launching of the first ever fully designed and manufactured domestic space vehicle. The project is based on technical knowledge gained in previous space experiences, particularly in developing GASCAN automatic experiments for NASA's space shuttle, and in some support obtained from the local team which assembled the México-OSCAR-30 microsatellites. Satex includes three autonomous payloads and a power subsystem, each one with a local microcomputer to provide intelligent and dedicated control. It also contains a flight computer (FC) with a pair of full redundancies. This enables the remote maintenance of processing boards from the ground station. A fourth communications payload depends on the flight computer for control purposes. A fifth payload was decided to be developed for the satellite. It adds value to the available on-board computers and extends the opportunity for a developing country to learn and to generate domestic space technology. Its aim is to provide automatic maintenance capabilities for the most critical on-board computer in order to achieve continuous satellite operations. This paper presents the virtual computer architecture specially developed to provide maintenance capabilities to the flight computer. The architecture is periodically implemented by software with a small amount of physical processors (FC processors) and virtual redundancies (payload processors) to emulate a hybrid redundancy computer. Communications among processors are accomplished over a fault-tolerant LAN. This allows a versatile operating behavior in terms of data communication as well as in terms of distributed fault tolerance. Obtained results, payload validation and reliability results are also presented.

  7. Fluid Intelligence and Automatic Neural Processes in Facial Expression Perception

    DEFF Research Database (Denmark)

    Liu, Tongran; Xiao, Tong; Li, Xiaoyan

    2015-01-01

    The relationship between human fluid intelligence and social-emotional abilities has been a topic of considerable interest. The current study investigated whether adolescents with different intellectual levels had different automatic neural processing of facial expressions. Two groups of adolescent...... males were enrolled: a high IQ group and an average IQ group. Age and parental socioeconomic status were matched between the two groups. Participants counted the numbers of the central cross changes while paired facial expressions were presented bilaterally in an oddball paradigm. There were two.......2). Participants were required to concentrate on the primary task of counting the central cross changes and to ignore the expressions to ensure that facial expression processing was automatic. Event-related potentials (ERPs) were obtained during the tasks. The visual mismatch negativity (vMMN) components were...

  8. Integrating artificial and human intelligence into tablet production process.

    Science.gov (United States)

    Gams, Matjaž; Horvat, Matej; Ožek, Matej; Luštrek, Mitja; Gradišek, Anton

    2014-12-01

    We developed a new machine learning-based method in order to facilitate the manufacturing processes of pharmaceutical products, such as tablets, in accordance with the Process Analytical Technology (PAT) and Quality by Design (QbD) initiatives. Our approach combines the data, available from prior production runs, with machine learning algorithms that are assisted by a human operator with expert knowledge of the production process. The process parameters encompass those that relate to the attributes of the precursor raw materials and those that relate to the manufacturing process itself. During manufacturing, our method allows production operator to inspect the impacts of various settings of process parameters within their proven acceptable range with the purpose of choosing the most promising values in advance of the actual batch manufacture. The interaction between the human operator and the artificial intelligence system provides improved performance and quality. We successfully implemented the method on data provided by a pharmaceutical company for a particular product, a tablet, under development. We tested the accuracy of the method in comparison with some other machine learning approaches. The method is especially suitable for analyzing manufacturing processes characterized by a limited amount of data.

  9. Synthetic-Creative Intelligence and Psychometric Intelligence: Analysis of the Threshold Theory and Creative Process

    Science.gov (United States)

    Ferrando, Mercedes; Soto, Gloria; Prieto, Lola; Sáinz, Marta; Ferrándiz, Carmen

    2016-01-01

    There has been an increasing body of research to uncover the relationship between creativity and intelligence. This relationship usually has been examined using traditional measures of intelligence and seldom using new approaches (i.e. Ferrando et al. 2005). In this work, creativity is measured by tools developed based on Sternberg's successful…

  10. The brain as a distributed intelligent processing system: an EEG study.

    Science.gov (United States)

    da Rocha, Armando Freitas; Rocha, Fábio Theoto; Massad, Eduardo

    2011-03-15

    Various neuroimaging studies, both structural and functional, have provided support for the proposal that a distributed brain network is likely to be the neural basis of intelligence. The theory of Distributed Intelligent Processing Systems (DIPS), first developed in the field of Artificial Intelligence, was proposed to adequately model distributed neural intelligent processing. In addition, the neural efficiency hypothesis suggests that individuals with higher intelligence display more focused cortical activation during cognitive performance, resulting in lower total brain activation when compared with individuals who have lower intelligence. This may be understood as a property of the DIPS. In our study, a new EEG brain mapping technique, based on the neural efficiency hypothesis and the notion of the brain as a Distributed Intelligence Processing System, was used to investigate the correlations between IQ evaluated with WAIS (Wechsler Adult Intelligence Scale) and WISC (Wechsler Intelligence Scale for Children), and the brain activity associated with visual and verbal processing, in order to test the validity of a distributed neural basis for intelligence. The present results support these claims and the neural efficiency hypothesis.

  11. The brain as a distributed intelligent processing system: an EEG study.

    Directory of Open Access Journals (Sweden)

    Armando Freitas da Rocha

    Full Text Available BACKGROUND: Various neuroimaging studies, both structural and functional, have provided support for the proposal that a distributed brain network is likely to be the neural basis of intelligence. The theory of Distributed Intelligent Processing Systems (DIPS, first developed in the field of Artificial Intelligence, was proposed to adequately model distributed neural intelligent processing. In addition, the neural efficiency hypothesis suggests that individuals with higher intelligence display more focused cortical activation during cognitive performance, resulting in lower total brain activation when compared with individuals who have lower intelligence. This may be understood as a property of the DIPS. METHODOLOGY AND PRINCIPAL FINDINGS: In our study, a new EEG brain mapping technique, based on the neural efficiency hypothesis and the notion of the brain as a Distributed Intelligence Processing System, was used to investigate the correlations between IQ evaluated with WAIS (Wechsler Adult Intelligence Scale and WISC (Wechsler Intelligence Scale for Children, and the brain activity associated with visual and verbal processing, in order to test the validity of a distributed neural basis for intelligence. CONCLUSION: The present results support these claims and the neural efficiency hypothesis.

  12. The Brain as a Distributed Intelligent Processing System: An EEG Study

    Science.gov (United States)

    da Rocha, Armando Freitas; Rocha, Fábio Theoto; Massad, Eduardo

    2011-01-01

    Background Various neuroimaging studies, both structural and functional, have provided support for the proposal that a distributed brain network is likely to be the neural basis of intelligence. The theory of Distributed Intelligent Processing Systems (DIPS), first developed in the field of Artificial Intelligence, was proposed to adequately model distributed neural intelligent processing. In addition, the neural efficiency hypothesis suggests that individuals with higher intelligence display more focused cortical activation during cognitive performance, resulting in lower total brain activation when compared with individuals who have lower intelligence. This may be understood as a property of the DIPS. Methodology and Principal Findings In our study, a new EEG brain mapping technique, based on the neural efficiency hypothesis and the notion of the brain as a Distributed Intelligence Processing System, was used to investigate the correlations between IQ evaluated with WAIS (Whechsler Adult Intelligence Scale) and WISC (Wechsler Intelligence Scale for Children), and the brain activity associated with visual and verbal processing, in order to test the validity of a distributed neural basis for intelligence. Conclusion The present results support these claims and the neural efficiency hypothesis. PMID:21423657

  13. Intelligent sensor networks the integration of sensor networks, signal processing and machine learning

    CERN Document Server

    Hu, Fei

    2012-01-01

    Although governments worldwide have invested significantly in intelligent sensor network research and applications, few books cover intelligent sensor networks from a machine learning and signal processing perspective. Filling this void, Intelligent Sensor Networks: The Integration of Sensor Networks, Signal Processing and Machine Learning focuses on the close integration of sensing, networking, and smart signal processing via machine learning. Based on the world-class research of award-winning authors, the book provides a firm grounding in the fundamentals of intelligent sensor networks, incl

  14. Intelligent control system for continuous technological process of alkylation

    Science.gov (United States)

    Gebel, E. S.; Hakimov, R. A.

    2018-01-01

    Relevance of intelligent control for complex dynamic objects and processes are shown in this paper. The model of a virtual analyzer based on a neural network is proposed. Comparative analysis of mathematical models implemented in MathLab software showed that the most effective from the point of view of the reproducibility of the result is the model with seven neurons in the hidden layer, the training of which was performed using the method of scaled coupled gradients. Comparison of the data from the laboratory analysis and the theoretical model are showed that the root-mean-square error does not exceed 3.5, and the calculated value of the correlation coefficient corresponds to a "strong" connection between the values.

  15. The process of implementing Competitive Intelligence in a company

    OpenAIRE

    František Bartes

    2013-01-01

    It is a common occurrence in business practice that the management of a company, in an effort to jump-start the function of the Competitive Intelligence unit, makes a number of mistakes and errors. Yet it is not difficult to avoid these missteps and achieve the desired level of Competitive Intelligence activities in a purposeful and effective manner. The author believes that a resolution of this problem lies in his concept of Competitive Intelligence viewed as a system application discipline ...

  16. Intelligent Integration between Human Simulated Intelligence and Expert Control Technology for the Combustion Process of Gas Heating Furnace

    Directory of Open Access Journals (Sweden)

    Yucheng Liu

    2014-01-01

    Full Text Available Due to being poor in control quality of the combustion process of gas heating furnace, this paper explored a sort of strong robust control algorithm in order to improve the control quality of the combustion process of gas heating furnace. The paper analyzed the control puzzle in the complex combustion process of gas heating furnace, summarized the cybernetics characteristic of the complex combustion process, researched into control strategy of the uncertainty complex control process, discussed the control model of the complex process, presented a sort of intelligent integration between human-simulated intelligence and expert control technology, and constructed the control algorithm for the combustion process controlling of gas heating furnace. The simulation results showed that the control algorithm proposed in the paper is not only better in dynamic and steady quality of the combustion process, but also obvious in energy saving effect, feasible, and effective in control strategy.

  17. Natural language processing in an intelligent writing strategy tutoring system.

    Science.gov (United States)

    McNamara, Danielle S; Crossley, Scott A; Roscoe, Rod

    2013-06-01

    The Writing Pal is an intelligent tutoring system that provides writing strategy training. A large part of its artificial intelligence resides in the natural language processing algorithms to assess essay quality and guide feedback to students. Because writing is often highly nuanced and subjective, the development of these algorithms must consider a broad array of linguistic, rhetorical, and contextual features. This study assesses the potential for computational indices to predict human ratings of essay quality. Past studies have demonstrated that linguistic indices related to lexical diversity, word frequency, and syntactic complexity are significant predictors of human judgments of essay quality but that indices of cohesion are not. The present study extends prior work by including a larger data sample and an expanded set of indices to assess new lexical, syntactic, cohesion, rhetorical, and reading ease indices. Three models were assessed. The model reported by McNamara, Crossley, and McCarthy (Written Communication 27:57-86, 2010) including three indices of lexical diversity, word frequency, and syntactic complexity accounted for only 6% of the variance in the larger data set. A regression model including the full set of indices examined in prior studies of writing predicted 38% of the variance in human scores of essay quality with 91% adjacent accuracy (i.e., within 1 point). A regression model that also included new indices related to rhetoric and cohesion predicted 44% of the variance with 94% adjacent accuracy. The new indices increased accuracy but, more importantly, afford the means to provide more meaningful feedback in the context of a writing tutoring system.

  18. Advances in intelligent process-aware information systems concepts, methods, and technologies

    CERN Document Server

    Oberhauser, Roy; Reichert, Manfred

    2017-01-01

    This book provides a state-of-the-art perspective on intelligent process-aware information systems and presents chapters on specific facets and approaches applicable to such systems. Further, it highlights novel advances and developments in various aspects of intelligent process-aware information systems and business process management systems. Intelligence capabilities are increasingly being integrated into or created in many of today’s software products and services. Process-aware information systems provide critical computing infrastructure to support the various processes involved in the creation and delivery of business products and services. Yet the integration of intelligence capabilities into process-aware information systems is a non-trivial yet necessary evolution of these complex systems. The book’s individual chapters address adaptive process management, case management processes, autonomically-capable processes, process-oriented information logistics, process recommendations, reasoning over ...

  19. Data Processing Languages for Business Intelligence. SQL vs. R

    Directory of Open Access Journals (Sweden)

    Marin FOTACHE

    2016-01-01

    Full Text Available As data centric approach, Business Intelligence (BI deals with the storage, integration, processing, exploration and analysis of information gathered from multiple sources in various formats and volumes. BI systems are generally synonymous to costly, complex platforms that require vast organizational resources. But there is also an-other face of BI, that of a pool of data sources, applications, services developed at different times using different technologies. This is “democratic” BI or, in some cases, “fragmented”, “patched” (or “chaotic” BI. Fragmentation creates not only integration problems, but also supports BI agility as new modules can be quickly developed. Among various languages and tools that cover large extents of BI activities, SQL and R are instrumental for both BI platform developers and BI users. SQL and R address both monolithic and democratic BI. This paper compares essential data processing features of two languages, identifying similarities and differences among them and also their strengths and limits.

  20. Feature-based tolerancing for intelligent inspection process definition

    International Nuclear Information System (INIS)

    Brown, C.W.

    1993-07-01

    This paper describes a feature-based tolerancing capability that complements a geometric solid model with an explicit representation of conventional and geometric tolerances. This capability is focused on supporting an intelligent inspection process definition system. The feature-based tolerance model's benefits include advancing complete product definition initiatives (e.g., STEP -- Standard for Exchange of Product model dam), suppling computer-integrated manufacturing applications (e.g., generative process planning and automated part programming) with product definition information, and assisting in the solution of measurement performance issues. A feature-based tolerance information model was developed based upon the notion of a feature's toleranceable aspects and describes an object-oriented scheme for representing and relating tolerance features, tolerances, and datum reference frames. For easy incorporation, the tolerance feature entities are interconnected with STEP solid model entities. This schema will explicitly represent the tolerance specification for mechanical products, support advanced dimensional measurement applications, and assist in tolerance-related methods divergence issues

  1. Simulation research on the process of large scale ship plane segmentation intelligent workshop

    Science.gov (United States)

    Xu, Peng; Liao, Liangchuang; Zhou, Chao; Xue, Rui; Fu, Wei

    2017-04-01

    Large scale ship plane segmentation intelligent workshop is a new thing, and there is no research work in related fields at home and abroad. The mode of production should be transformed by the existing industry 2.0 or part of industry 3.0, also transformed from "human brain analysis and judgment + machine manufacturing" to "machine analysis and judgment + machine manufacturing". In this transforming process, there are a great deal of tasks need to be determined on the aspects of management and technology, such as workshop structure evolution, development of intelligent equipment and changes in business model. Along with them is the reformation of the whole workshop. Process simulation in this project would verify general layout and process flow of large scale ship plane section intelligent workshop, also would analyze intelligent workshop working efficiency, which is significant to the next step of the transformation of plane segmentation intelligent workshop.

  2. Information Processing and Coaching Treatments in an Intelligent Tutoring System

    National Research Council Canada - National Science Library

    Dillon, Ronna

    1997-01-01

    The purpose of this effort was to develop an intelligent tutoring system (ITS) to train test administrators how to operate computerized adaptive testing Armed Services Vocational Aptitude Battery (CAT-ASVAB...

  3. Artificial intelligence in NMR imaging and image processing

    International Nuclear Information System (INIS)

    Kuhn, M.H.

    1988-01-01

    NMR tomography offers a wealth of information and data acquisition variants. Artificial intelligence is able to efficiently support the selection of measuring parameters and the evaluation of results. (orig.) [de

  4. Intelligent technologies in process of highly-precise products manufacturing

    Science.gov (United States)

    Vakhidova, K. L.; Khakimov, Z. L.; Isaeva, M. R.; Shukhin, V. V.; Labazanov, M. A.; Ignatiev, S. A.

    2017-10-01

    One of the main control methods of the surface layer of bearing parts is the eddy current testing method. Surface layer defects of bearing parts, like burns, cracks and some others, are reflected in the results of the rolling surfaces scan. The previously developed method for detecting defects from the image of the raceway was quite effective, but the processing algorithm is complicated and lasts for about 12 ... 16 s. The real non-stationary signals from an eddy current transducer (ECT) consist of short-time high-frequency and long-time low-frequency components, therefore a transformation is used for their analysis, which provides different windows for different frequencies. The wavelet transform meets these conditions. Based on aforesaid, a methodology for automatically detecting and recognizing local defects in bearing parts surface layer has been developed on the basis of wavelet analysis using integral estimates. Some of the defects are recognized by the amplitude component, otherwise an automatic transition to recognition by the phase component of information signals (IS) is carried out. The use of intelligent technologies in the manufacture of bearing parts will, firstly, significantly improve the quality of bearings, and secondly, significantly improve production efficiency by reducing (eliminating) rejections in the manufacture of products, increasing the period of normal operation of the technological equipment (inter-adjustment period), the implementation of the system of Flexible facilities maintenance, as well as reducing production costs.

  5. Detection, information fusion, and temporal processing for intelligence in recognition

    Energy Technology Data Exchange (ETDEWEB)

    Casasent, D. [Carnegie Mellon Univ., Pittsburgh, PA (United States)

    1996-12-31

    The use of intelligence in vision recognition uses many different techniques or tools. This presentation discusses several of these techniques for recognition. The recognition process is generally separated into several steps or stages when implemented in hardware, e.g. detection, segmentation and enhancement, and recognition. Several new distortion-invariant filters, biologically-inspired Gabor wavelet filter techniques, and morphological operations that have been found very useful for detection and clutter rejection are discussed. These are all shift-invariant operations that allow multiple object regions of interest in a scene to be located in parallel. We also discuss new algorithm fusion concepts by which the results from different detection algorithms are combined to reduce detection false alarms; these fusion methods utilize hierarchical processing and fuzzy logic concepts. We have found this to be most necessary, since no single detection algorithm is best for all cases. For the final recognition stage, we describe a new method of representing all distorted versions of different classes of objects and determining the object class and pose that most closely matches that of a given input. Besides being efficient in terms of storage and on-line computations required, it overcomes many of the problems that other classifiers have in terms of the required training set size, poor generalization with many hidden layer neurons, etc. It is also attractive in its ability to reject input regions as clutter (non-objects) and to learn new object descriptions. We also discuss its use in processing a temporal sequence of input images of the contents of each local region of interest. We note how this leads to robust results in which estimation efforts in individual frames can be overcome. This seems very practical, since in many scenarios a decision need not be made after only one frame of data, since subsequent frames of data enter immediately in sequence.

  6. A MURI Center for Intelligent Biomimetic Image Processing and Classification

    Science.gov (United States)

    2007-11-01

    times, labeled "plage" or "open space" or "natural", the system learns to associate multiple classes with a given input. Testbed image examples have shown...brain color perception and category learning. Commentary on "Coordinating perceptually grounded categories through language " by Luc Steels and Tony...Symposium on Computational Intelligence (ISCI), Kosice, Slovakia, June 2002. 9. Carpenter, G.A., Award from the Slovak Artificial Intelligence Society, 2002

  7. Racial Equality in Intelligence: Predictions from a Theory of Intelligence as Processing

    Science.gov (United States)

    Fagan, Joseph F.; Holland, Cynthia R.

    2007-01-01

    African-Americans and Whites were asked to solve problems typical of those administered on standard tests of intelligence. Half of the problems were solvable on the basis of information generally available to either race and/or on the basis of information newly learned. Such knowledge did not vary with race. Other problems were only solvable on…

  8. Effect of promoting self-esteem by participatory learning process on emotional intelligence among early adolescents.

    Science.gov (United States)

    Munsawaengsub, Chokchai; Yimklib, Somkid; Nanthamongkolchai, Sutham; Apinanthavech, Suporn

    2009-12-01

    To study the effect of promoting self-esteem by participatory learning program on emotional intelligence among early adolescents. The quasi-experimental study was conducted in grade 9 students from two schools in Bangbuathong district, Nonthaburi province. Each experimental and comparative group consisted of 34 students with the lowest score of emotional intelligence. The instruments were questionnaires, Program to Develop Emotional Intelligence and Handbook of Emotional Intelligence Development. The experimental group attended 8 participatory learning activities in 4 weeks to Develop Emotional Intelligence while the comparative group received the handbook for self study. Assessment the effectiveness of program was done by pre-test and post-test immediately and 4 weeks apart concerning the emotional intelligence. Implementation and evaluation was done during May 24-August 12, 2005. Data were analyzed by frequency, percentage, mean, standard deviation, Chi-square, independent sample t-test and paired sample t-test. Before program implementation, both groups had no statistical difference in mean score of emotional intelligence. After intervention, the experimental group had higher mean score of emotional intelligence both immediately and 4 weeks later with statistical significant (p = 0.001 and self-esteem by participatory learning process could enhance the emotional intelligence in early-adolescent. This program could be modified and implemented for early adolescent in the community.

  9. Process monitoring for intelligent manufacturing processes - Methodology and application to Robot Assisted Polishing

    DEFF Research Database (Denmark)

    Pilny, Lukas

    Process monitoring provides important information on the product, process and manufacturing system during part manufacturing. Such information can be used for process optimization and detection of undesired processing conditions to initiate timely actions for avoidance of defects, thereby improving...... quality assurance. This thesis is aimed at a systematic development of process monitoring solutions, constituting a key element of intelligent manufacturing systems towards zero defect manufacturing. A methodological approach of general applicability is presented in this concern.The approach consists...... of six consecutive steps for identification of product Vital Quality Characteristics (VQCs) and Key Process Variables (KPVs), selection and characterization of sensors, optimization of sensors placement, validation of the monitoring solutions, definition of the reference manufacturing performance...

  10. Processing of acceleration and dive data on-board satellite relay tags to investigate diving and foraging behaviour in free-ranging marine predators.

    Science.gov (United States)

    Cox, Sam L; Orgeret, Florian; Gesta, Mathieu; Rodde, Charles; Heizer, Isaac; Weimerskirch, Henri; Guinet, Christophe

    2018-01-01

    Biologging technologies are changing the way in which the marine environment is observed and monitored. However, because device retrieval is typically required to access the high-resolution data they collect, their use is generally restricted to those animals that predictably return to land. Data abstraction and transmission techniques aim to address this, although currently these are limited in scope and do not incorporate, for example, acceleration measurements which can quantify animal behaviours and movement patterns over fine-scales.In this study, we present a new method for the collection, abstraction and transmission of accelerometer data from free-ranging marine predators via the Argos satellite system. We test run the technique on 20 juvenile southern elephant seals Mirounga leonina from the Kerguelen Islands during their first months at sea following weaning. Using retrieved archival data from nine individuals that returned to the colony, we compare and validate abstracted transmissions against outputs from established accelerometer processing procedures.Abstracted transmissions included estimates, across five segments of a dive profile, of time spent in prey catch attempt (PrCA) behaviours, swimming effort and pitch. These were then summarised and compared to archival outputs across three dive phases: descent, bottom and ascent. Correlations between the two datasets were variable but generally good (dependent on dive phase, marginal R 2 values of between .45 and .6 to >.9) and consistent between individuals. Transmitted estimates of PrCA behaviours and swimming effort were positively biased to those from archival processing.Data from this study represent some of the first remotely transmitted quantifications from accelerometers. The methods presented and analysed can be used to provide novel insight towards the behaviours and movements of free-ranging marine predators, such as juvenile southern elephant seals, from whom logger retrieval is challenging

  11. Intelligent systems/software engineering methodology - A process to manage cost and risk

    Science.gov (United States)

    Friedlander, Carl; Lehrer, Nancy

    1991-01-01

    A systems development methodology is discussed that has been successfully applied to the construction of a number of intelligent systems. This methodology is a refinement of both evolutionary and spiral development methodologies. It is appropriate for development of intelligent systems. The application of advanced engineering methodology to the development of software products and intelligent systems is an important step toward supporting the transition of AI technology into aerospace applications. A description of the methodology and the process model from which it derives is given. Associated documents and tools are described which are used to manage the development process and record and report the emerging design.

  12. Decision Support for Software Process Management Teams: An Intelligent Software Agent Approach

    National Research Council Canada - National Science Library

    Church, Lori

    2000-01-01

    ... to market, eliminate redundancy, and ease job stress. This thesis proposes a conceptual model for software process management decision support in the form of an intelligent software agent network...

  13. Interated Intelligent Industrial Process Sensing and Control: Applied to and Demonstrated on Cupola Furnaces

    Energy Technology Data Exchange (ETDEWEB)

    Mohamed Abdelrahman; roger Haggard; Wagdy Mahmoud; Kevin Moore; Denis Clark; Eric Larsen; Paul King

    2003-02-12

    The final goal of this project was the development of a system that is capable of controlling an industrial process effectively through the integration of information obtained through intelligent sensor fusion and intelligent control technologies. The industry of interest in this project was the metal casting industry as represented by cupola iron-melting furnaces. However, the developed technology is of generic type and hence applicable to several other industries. The system was divided into the following four major interacting components: 1. An object oriented generic architecture to integrate the developed software and hardware components @. Generic algorithms for intelligent signal analysis and sensor and model fusion 3. Development of supervisory structure for integration of intelligent sensor fusion data into the controller 4. Hardware implementation of intelligent signal analysis and fusion algorithms

  14. SmartWeld/SmartProcess - intelligent model based system for the design and validation of welding processes

    Energy Technology Data Exchange (ETDEWEB)

    Mitchner, J.

    1996-04-01

    Diagrams are presented on an intelligent model based system for the design and validation of welding processes. Key capabilities identified include `right the first time` manufacturing, continuous improvement, and on-line quality assurance.

  15. The Relationship between Multiple Intelligences with Preferred Science Teaching and Science Process Skills

    OpenAIRE

    Mohd Ali Samsudin; Noor Hasyimah Haniza; Corrienna Abdul-Talib; Hayani Marlia Mhd Ibrahim

    2015-01-01

    This study was undertaken to identify the relationship between multiple intelligences with preferred science teaching and science process skills. The design of the study is a survey using three questionnaires reported in the literature: Multiple Intelligences Questionnaire, Preferred Science Teaching Questionnaire and Science Process Skills Questionnaire. The study selected 300 primary school students from five (5) primary schools in Penang, Malaysia. The findings showed a relationship betwee...

  16. The application of neural networks with artificial intelligence technique in the modeling of industrial processes

    International Nuclear Information System (INIS)

    Saini, K. K.; Saini, Sanju

    2008-01-01

    Neural networks are a relatively new artificial intelligence technique that emulates the behavior of biological neural systems in digital software or hardware. These networks can 'learn', automatically, complex relationships among data. This feature makes the technique very useful in modeling processes for which mathematical modeling is difficult or impossible. The work described here outlines some examples of the application of neural networks with artificial intelligence technique in the modeling of industrial processes.

  17. Financial intelligence of business process outsourcing professional in Davao City Philippines

    Directory of Open Access Journals (Sweden)

    Samantha Ferraren

    2016-12-01

    Full Text Available This research determined the financial intelligence using the Kiyosaki Cashflow Quadrant. The study employed the Kiyosaki Cashflow Quadrant to classify employees financial intelligence as likely to be an investor, big business owner, self-employed and employed. The Ordinal Regression was employed in determining the parameters of the chosen variables through Maximum Likelihood Estimation (MLE. The results showed that income is a significant factor in the financial intelligence of the Business Process Outsourcing (BPO employees; the higher the income the better is the financial intelligence. The type of BPO employer is a significantly determined by the degree of financial intelligence in the BPO employees in financial services had higher financial intelligence than that of non-financial services. There is a significant relationship between financial literacy and financial intelligence.Although, there were some rank and file employees who earned less, and they may be classified as investor because of their behavior towards money. Financial wellness program for BPO employees in financial and non-financial services alike was recommended to improve financial intelligence to be able to achieve financial freedom .

  18. Artificial Intelligence in ADA: Pattern-Directed Processing. Final Report.

    Science.gov (United States)

    Reeker, Larry H.; And Others

    To demonstrate to computer programmers that the programming language Ada provides superior facilities for use in artificial intelligence applications, the three papers included in this report investigate the capabilities that exist within Ada for "pattern-directed" programming. The first paper (Larry H. Reeker, Tulane University) is…

  19. Gender Quotas on Board of Directors

    DEFF Research Database (Denmark)

    Smith, Nina

    2013-01-01

    Beside arguments of fairness and equal opportunities, it is often argued that gender diversity on boards of directors may improve firm performance, but the empirical results are mixed and often negative. Based on the available research, gender quotas on boards of directors cannot be justified...

  20. Is general intelligence little more than the speed of higher-order processing?

    Science.gov (United States)

    Schubert, Anna-Lena; Hagemann, Dirk; Frischkorn, Gidon T

    2017-10-01

    Individual differences in the speed of information processing have been hypothesized to give rise to individual differences in general intelligence. Consistent with this hypothesis, reaction times (RTs) and latencies of event-related potential have been shown to be moderately associated with intelligence. These associations have been explained either in terms of individual differences in some brain-wide property such as myelination, the speed of neural oscillations, or white-matter tract integrity, or in terms of individual differences in specific processes such as the signal-to-noise ratio in evidence accumulation, executive control, or the cholinergic system. Here we show in a sample of 122 participants, who completed a battery of RT tasks at 2 laboratory sessions while an EEG was recorded, that more intelligent individuals have a higher speed of higher-order information processing that explains about 80% of the variance in general intelligence. Our results do not support the notion that individuals with higher levels of general intelligence show advantages in some brain-wide property. Instead, they suggest that more intelligent individuals benefit from a more efficient transmission of information from frontal attention and working memory processes to temporal-parietal processes of memory storage. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

  1. Original article Functioning of memory and attention processes in children with intelligence below average

    Directory of Open Access Journals (Sweden)

    Aneta Rita Borkowska

    2014-05-01

    Full Text Available BACKGROUND The aim of the research was to assess memorization and recall of logically connected and unconnected material, coded graphically and linguistically, and the ability to focus attention, in a group of children with intelligence below average, compared to children with average intelligence. PARTICIPANTS AND PROCEDURE The study group included 27 children with intelligence below average. The control group consisted of 29 individuals. All of them were examined using the authors’ experimental trials and the TUS test (Attention and Perceptiveness Test. RESULTS Children with intelligence below average memorized significantly less information contained in the logical material, demonstrated lower ability to memorize the visual material, memorized significantly fewer words in the verbal material learning task, achieved lower results in such indicators of the visual attention process pace as the number of omissions and mistakes, and had a lower pace of perceptual work, compared to children with average intelligence. CONCLUSIONS The results confirm that children with intelligence below average have difficulties with memorizing new material, both logically connected and unconnected. The significantly lower capacity of direct memory is independent of modality. The results of the study on the memory process confirm the hypothesis about lower abilities of children with intelligence below average, in terms of concentration, work pace, efficiency and perception.

  2. The role of across-frequency envelope processing for speech intelligibility

    DEFF Research Database (Denmark)

    Chabot-Leclerc, Alexandre; Jørgensen, Søren; Dau, Torsten

    2013-01-01

    Speech intelligibility models consist of a preprocessing part that transforms the stimuli into some internal (auditory) representation, and a decision metric that quantifies effects of transmission channel, speech interferers, and auditory processing on the speech intelligibility. Here, two recent...... speech intelligibility models, the spectro-temporal modulation index [STMI; Elhilali et al. (2003)] and the speech-based envelope power spectrum model [sEPSM; Jørgensen and Dau (2011)] were evaluated in conditions of noisy speech subjected to reverberation, and to nonlinear distortions through either...

  3. The role of across-frequency envelope processing for speech intelligibility

    DEFF Research Database (Denmark)

    Chabot-Leclerc, Alexandre; Jørgensen, Søren; Dau, Torsten

    2013-01-01

    Speech intelligibility models consist of a preprocessing part that transforms the stimuli into some internal (auditory) representation, and a decision metric that quantifies effects of transmission channel, speech interferers, and auditory processing on the speech intelligibility. Here, two recent...... speech intelligibility models, the spectro-temporal modulation index (STMI; Elhilali et al., 2003) and the speech-based envelope power spectrum model (sEPSM; Jørgensen and Dau, 2011) were evaluated in conditions of noisy speech subjected to reverberation, and to nonlinear distortions through either...

  4. Mothers' daily person and process praise: implications for children's theory of intelligence and motivation.

    Science.gov (United States)

    Pomerantz, Eva M; Kempner, Sara G

    2013-11-01

    This research examined if mothers' day-to-day praise of children's success in school plays a role in children's theory of intelligence and motivation. Participants were 120 children (mean age = 10.23 years) and their mothers who took part in a 2-wave study spanning 6 months. During the first wave, mothers completed a 10-day daily interview in which they reported on their use of person (e.g., "You are smart") and process (e.g., "You tried hard") praise. Children's entity theory of intelligence and preference for challenge in school were assessed with surveys at both waves. Mothers' person, but not process, praise was predictive of children's theory of intelligence and motivation: The more person praise mothers used, the more children subsequently held an entity theory of intelligence and avoided challenge over and above their earlier functioning on these dimensions.

  5. Intelligent methods for the process parameter determination of plastic injection molding

    Science.gov (United States)

    Gao, Huang; Zhang, Yun; Zhou, Xundao; Li, Dequn

    2018-03-01

    Injection molding is one of the most widely used material processing methods in producing plastic products with complex geometries and high precision. The determination of process parameters is important in obtaining qualified products and maintaining product quality. This article reviews the recent studies and developments of the intelligent methods applied in the process parameter determination of injection molding. These intelligent methods are classified into three categories: Case-based reasoning methods, expert system- based methods, and data fitting and optimization methods. A framework of process parameter determination is proposed after comprehensive discussions. Finally, the conclusions and future research topics are discussed.

  6. Cognitive and emotional demands of black humour processing: the role of intelligence, aggressiveness and mood.

    Science.gov (United States)

    Willinger, Ulrike; Hergovich, Andreas; Schmoeger, Michaela; Deckert, Matthias; Stoettner, Susanne; Bunda, Iris; Witting, Andrea; Seidler, Melanie; Moser, Reinhilde; Kacena, Stefanie; Jaeckle, David; Loader, Benjamin; Mueller, Christian; Auff, Eduard

    2017-05-01

    Humour processing is a complex information-processing task that is dependent on cognitive and emotional aspects which presumably influence frame-shifting and conceptual blending, mental operations that underlie humour processing. The aim of the current study was to find distinctive groups of subjects with respect to black humour processing, intellectual capacities, mood disturbance and aggressiveness. A total of 156 adults rated black humour cartoons and conducted measurements of verbal and nonverbal intelligence, mood disturbance and aggressiveness. Cluster analysis yields three groups comprising following properties: (1) moderate black humour preference and moderate comprehension; average nonverbal and verbal intelligence; low mood disturbance and moderate aggressiveness; (2) low black humour preference and moderate comprehension; average nonverbal and verbal intelligence, high mood disturbance and high aggressiveness; and (3) high black humour preference and high comprehension; high nonverbal and verbal intelligence; no mood disturbance and low aggressiveness. Age and gender do not differ significantly, differences in education level can be found. Black humour preference and comprehension are positively associated with higher verbal and nonverbal intelligence as well as higher levels of education. Emotional instability and higher aggressiveness apparently lead to decreased levels of pleasure when dealing with black humour. These results support the hypothesis that humour processing involves cognitive as well as affective components and suggest that these variables influence the execution of frame-shifting and conceptual blending in the course of humour processing.

  7. Relationships among processing speed, working memory, and fluid intelligence in children.

    Science.gov (United States)

    Fry, A F; Hale, S

    2000-10-01

    The present review focuses on three issues, (a) the time course of developmental increases in cognitive abilities; (b) the impact of age on individual differences in these abilities, and (c) the mechanisms by which developmental increases in different aspects of cognition affect each other. We conclude from our review of the literature that the development of processing speed, working memory, and fluid intelligence, all follow a similar time course, suggesting that all three abilities develop in concert. Furthermore, the strength of the correlation between speed and intelligence does not appear to change with age, and most of the effect of the age-related increase in speed on intelligence appears to be mediated through the effect of speed on working memory. Finally, most of the effect of the age-related improvement in working memory on intelligence is itself attributable to the effect of the increase in speed on working memory, providing evidence of a cognitive developmental cascade.

  8. New Rationales for Women on Boards

    OpenAIRE

    Choudhury, B.

    2014-01-01

    Should measures promoting women to corporate boards be solely justified in terms of economic arguments? Traditionally, such measures have tended to rely on utilitarian arguments, despite the fact that the most prominent of these arguments—the relationship between women’s presence on boards and firm financial performance—is equivocal. Conversely, this article argues that rationales for increasing women on boards should be based on both equality and economics grounds. An equality rationale is n...

  9. Intelligent techniques in signal processing for multimedia security

    CERN Document Server

    Santhi, V

    2017-01-01

    This book proposes new algorithms to ensure secured communications and prevent unauthorized data exchange in secured multimedia systems. Focusing on numerous applications’ algorithms and scenarios, it offers an in-depth analysis of data hiding technologies including watermarking, cryptography, encryption, copy control, and authentication. The authors present a framework for visual data hiding technologies that resolves emerging problems of modern multimedia applications in several contexts including the medical, healthcare, education, and wireless communication networking domains. Further, it introduces several intelligent security techniques with real-time implementation. As part of its comprehensive coverage, the book discusses contemporary multimedia authentication and fingerprinting techniques, while also proposing personal authentication/recognition systems based on hand images, surveillance system security using gait recognition, face recognition under restricted constraints such as dry/wet face condi...

  10. The remarkable cell: Intelligently designed or by evolutionary process?

    Directory of Open Access Journals (Sweden)

    Mark Pretorius

    2013-02-01

    Full Text Available The objective of this article was to deal with the challenging theme of the Origin of Life. Science has been arguing the when and how of the beginning of life for centuries. It is a subject which remains perplexing despite all the technological advances made in science. The first part of the article dealt with the idea of a universe and earth divinely created to sustain life. The second part dealt with the premise that the first life forms were the miraculous work of an intelligent designer, which is revealed by the sophisticated and intricate design of these first life forms. The article concluded with an explanation that these life forms are in stark contrast to the idea of a random Darwinian type evolution for life�s origin, frequently referred to as abiogenesis or spontaneous generation.

  11. Towards a New Approach of the Economic Intelligence Process: Basic Concepts, Analysis Methods and Informational Tools

    Directory of Open Access Journals (Sweden)

    Sorin Briciu

    2009-04-01

    Full Text Available One of the obvious trends in current business environment is the increased competition. In this context, organizations are becoming more and more aware of the importance of knowledge as a key factor in obtaining competitive advantage. A possible solution in knowledge management is Economic Intelligence (EI that involves the collection, evaluation, processing, analysis, and dissemination of economic data (about products, clients, competitors, etc. inside organizations. The availability of massive quantities of data correlated with advances in information and communication technology allowing for the filtering and processing of these data provide new tools for the production of economic intelligence.The research is focused on innovative aspects of economic intelligence process (models of analysis, activities, methods and informational tools and is providing practical guidelines for initiating this process. In this paper, we try: (a to contribute to a coherent view on economic intelligence process (approaches, stages, fields of application; b to describe the most important models of analysis related to this process; c to analyze the activities, methods and tools associated with each stage of an EI process.

  12. Using Software Zelio Soft in Educational Process to Simulation Control Programs for Intelligent Relays

    Science.gov (United States)

    Michalik, Peter; Mital, Dusan; Zajac, Jozef; Brezikova, Katarina; Duplak, Jan; Hatala, Michal; Radchenko, Svetlana

    2016-10-01

    Article deals with point to using intelligent relay and PLC systems in practice, to their architecture and principles of programming and simulations for education process on all types of school from secondary to universities. Aim of the article is proposal of simple examples of applications, where is demonstrated methodology of programming on real simple practice examples and shown using of chosen instructions. In practical part is described process of creating schemas and describing of function blocks, where are described methodologies of creating program and simulations of output reactions on changeable inputs for intelligent relays.

  13. "Intelligent" tools for workflow process redesign : a research agenda

    NARCIS (Netherlands)

    Netjes, M.; Vanderfeesten, I.T.P.; Reijers, H.A.; Bussler, C.; Haller, A.

    2006-01-01

    Although much attention is being paid to business processes during the past decades, the design of business processes and particularly workflow processes is still more art than science. In this workshop paper, we present our view on modeling methods for workflow processes and introduce our research

  14. Competitive Intelligence.

    Science.gov (United States)

    Bergeron, Pierrette; Hiller, Christine A.

    2002-01-01

    Reviews the evolution of competitive intelligence since 1994, including terminology and definitions and analytical techniques. Addresses the issue of ethics; explores how information technology supports the competitive intelligence process; and discusses education and training opportunities for competitive intelligence, including core competencies…

  15. Optimization of Planck-LFI on-board data handling

    Energy Technology Data Exchange (ETDEWEB)

    Maris, M; Galeotta, S; Frailis, M; Zacchei, A; Fogliani, S; Gasparo, F [INAF-OATs, Via G.B. Tiepolo 11, 34131 Trieste (Italy); Tomasi, M; Bersanelli, M [Universita di Milano, Dipartimento di Fisica, Via G. Celoria 16, 20133 Milano (Italy); Miccolis, M [Thales Alenia Space Italia S.p.A., S.S. Padana Superiore 290, 20090 Vimodrone (Italy); Hildebrandt, S; Chulani, H; Gomez, F [Instituto de Astrofisica de Canarias (IAC), C/o Via Lactea, s/n E38205 - La Laguna, Tenerife (Spain); Rohlfs, R; Morisset, N; Binko, P [ISDC Data Centre for Astrophysics, University of Geneva, ch. d' Ecogia 16, 1290 Versoix (Switzerland); Burigana, C; Butler, R C; Cuttaia, F; Franceschi, E [INAF-IASF Bologna, Via P. Gobetti, 101, 40129 Bologna (Italy); D' Arcangelo, O, E-mail: maris@oats.inaf.i [IFP-CNR, via Cozzi 53, 20125 Milano (Italy)

    2009-12-15

    To asses stability against 1/f noise, the Low Frequency Instrument (LFI) on-board the Planck mission will acquire data at a rate much higher than the data rate allowed by the science telemetry bandwith of 35.5 Kbps. The data are processed by an on-board pipeline, followed on-ground by a decoding and reconstruction step, to reduce the volume of data to a level compatible with the bandwidth while minimizing the loss of information. This paper illustrates the on-board processing of the scientific data used by Planck/LFI to fit the allowed data-rate, an intrinsecally lossy process which distorts the signal in a manner which depends on a set of five free parameters (N{sub aver}, r{sub 1}, r{sub 2}, q, O) for each of the 44 LFI detectors. The paper quantifies the level of distortion introduced by the on-board processing as a function of these parameters. It describes the method of tuning the on-board processing chain to cope with the limited bandwidth while keeping to a minimum the signal distortion. Tuning is sensitive to the statistics of the signal and has to be constantly adapted during flight. The tuning procedure is based on a optimization algorithm applied to unprocessed and uncompressed raw data provided either by simulations, pre-launch tests or data taken in flight from LFI operating in a special diagnostic acquisition mode. All the needed optimization steps are performed by an automated tool, OCA2, which simulates the on-board processing, explores the space of possible combinations of parameters, and produces a set of statistical indicators, among them: the compression rate C{sub r} and the processing noise epsilon{sub Q}. For Planck/LFI it is required that C{sub r} = 2.4 while, as for other systematics, epsilon{sub Q} would have to be less than 10% of rms of the instrumental white noise. An analytical model is developed that is able to extract most of the relevant information on the processing errors and the compression rate as a function of the signal

  16. Processing Speed and Intelligence as Predictors of School Achievement: Mediation or Unique Contribution?

    Science.gov (United States)

    Dodonova, Yulia A.; Dodonov, Yury S.

    2012-01-01

    The relationships between processing speed, intelligence, and school achievement were analyzed on a sample of 184 Russian 16-year-old students. Two speeded tasks required the discrimination of simple geometrical shapes and the recognition of the presented meaningless figures. Raven's Advanced Progressive Matrices and the verbal subtests of…

  17. Optimization of chemical composition in the manufacturing process of flotation balls based on intelligent soft sensing

    Directory of Open Access Journals (Sweden)

    Dučić Nedeljko

    2016-01-01

    Full Text Available This paper presents an application of computational intelligence in modeling and optimization of parameters of two related production processes - ore flotation and production of balls for ore flotation. It is proposed that desired chemical composition of flotation balls (Mn=0.69%; Cr=2.247%; C=3.79%; Si=0.5%, which ensures minimum wear rate (0.47 g/kg during copper milling is determined by combining artificial neural network (ANN and genetic algorithm (GA. Based on the results provided by neuro-genetic combination, a second neural network was derived as an ‘intelligent soft sensor’ in the process of white cast iron production. The proposed ANN 12-16-12-4 model demonstrated favourable prediction capacity, and can be recommended as a ‘intelligent soft sensor’ in the alloying process intended for obtaining favourable chemical composition of white cast iron for production of flotation balls. In the development of intelligent soft sensor data from the two real production processes was used. [Projekat Ministarstva nauke Republike Srbije, br. TR35037 i br. TR35015

  18. A Multidirectional Model for Assessing Learning Disabled Students' Intelligence: An Information-Processing Framework.

    Science.gov (United States)

    Swanson, H. Lee

    1982-01-01

    An information processing approach to the assessment of learning disabled students' intellectual performance is presented. The model is based on the assumption that intelligent behavior is comprised of a variety of problem- solving strategies. An account of child problem solving is explained and illustrated with a "thinking aloud" protocol.…

  19. The influence of masker type on early reflection processing and speech intelligibility (L)

    DEFF Research Database (Denmark)

    Arweiler, Iris; Buchholz, Jörg M.; Dau, Torsten

    2013-01-01

    Arweiler and Buchholz [J. Acoust. Soc. Am. 130, 996-1005 (2011)] showed that, while the energy of early reflections (ERs) in a room improves speech intelligibility, the benefit is smaller than that provided by the energy of the direct sound (DS). In terms of integration of ERs and DS, binaural...... listening did not provide a benefit from ERs apart from a binaural energy summation, such that monaural auditory processing could account for the data. However, a diffuse speech shaped noise (SSN) was used in the speech intelligibility experiments, which does not provide distinct binaural cues...... to the auditory system. In the present study, the monaural and binaural benefit from ERs for speech intelligibility was investigated using three directional maskers presented from 90° azimuth: a SSN, a multi-talker babble, and a reversed two-talker masker. For normal-hearing as well as hearing-impaired listeners...

  20. Integrated Intelligent Modeling, Design and Control of Crystal Growth Processes

    National Research Council Canada - National Science Library

    Prasad, V

    2000-01-01

    .... This MURI program took an integrated approach towards modeling, design and control of crystal growth processes and in conjunction with growth and characterization experiments developed much better...

  1. Interactive analysis of geodata based intelligence

    Science.gov (United States)

    Wagner, Boris; Eck, Ralf; Unmüessig, Gabriel; Peinsipp-Byma, Elisabeth

    2016-05-01

    When a spatiotemporal events happens, multi-source intelligence data is gathered to understand the problem, and strategies for solving the problem are investigated. The difficulties arising from handling spatial and temporal intelligence data represent the main problem. The map might be the bridge to visualize the data and to get the most understand model for all stakeholders. For the analysis of geodata based intelligence data, a software was developed as a working environment that combines geodata with optimized ergonomics. The interaction with the common operational picture (COP) is so essentially facilitated. The composition of the COP is based on geodata services, which are normalized by international standards of the Open Geospatial Consortium (OGC). The basic geodata are combined with intelligence data from images (IMINT) and humans (HUMINT), stored in a NATO Coalition Shared Data Server (CSD). These intelligence data can be combined with further information sources, i.e., live sensors. As a result a COP is generated and an interaction suitable for the specific workspace is added. This allows the users to work interactively with the COP, i.e., searching with an on board CSD client for suitable intelligence data and integrate them into the COP. Furthermore, users can enrich the scenario with findings out of the data of interactive live sensors and add data from other sources. This allows intelligence services to contribute effectively to the process by what military and disaster management are organized.

  2. Modeling and Control of Multivariable Process Using Intelligent Techniques

    Directory of Open Access Journals (Sweden)

    Subathra Balasubramanian

    2010-10-01

    Full Text Available For nonlinear dynamic systems, the first principles based modeling and control is difficult to implement. In this study, a fuzzy controller and recurrent fuzzy controller are developed for MIMO process. Fuzzy logic controller is a model free controller designed based on the knowledge about the process. In fuzzy controller there are two types of rule-based fuzzy models are available: one the linguistic (Mamdani model and the other is Takagi–Sugeno model. Of these two, Takagi-Sugeno model (TS has attracted most attention. The fuzzy controller application is limited to static processes due to their feedforward structure. But, most of the real-time processes are dynamic and they require the history of input/output data. In order to store the past values a memory unit is needed, which is introduced by the recurrent structure. The proposed recurrent fuzzy structure is used to develop a controller for the two tank heating process. Both controllers are designed and implemented in a real time environment and their performance is compared.

  3. Business Intelligence Applied to the ALMA Software Integration Process

    Science.gov (United States)

    Zambrano, M.; Recabarren, C.; González, V.; Hoffstadt, A.; Soto, R.; Shen, T.-C.

    2012-09-01

    Software quality assurance and planning of an astronomy project is a complex task, specially if it is a distributed collaborative project such as ALMA, where the development centers are spread across the globe. When you execute a software project there is much valuable information about this process itself that you might be able to collect. One of the ways you can receive this input is via an issue tracking system that will gather the problem reports relative to software bugs captured during the testing of the software, during the integration of the different components or even worst, problems occurred during production time. Usually, there is little time spent on analyzing them but with some multidimensional processing you can extract valuable information from them and it might help you on the long term planning and resources allocation. We present an analysis of the information collected at ALMA from a collection of key unbiased indicators. We describe here the extraction, transformation and load process and how the data was processed. The main goal is to assess a software process and get insights from this information.

  4. Intelligent process mapping through systematic improvement of heuristics

    Science.gov (United States)

    Ieumwananonthachai, Arthur; Aizawa, Akiko N.; Schwartz, Steven R.; Wah, Benjamin W.; Yan, Jerry C.

    1992-01-01

    The present system for automatic learning/evaluation of novel heuristic methods applicable to the mapping of communication-process sets on a computer network has its basis in the testing of a population of competing heuristic methods within a fixed time-constraint. The TEACHER 4.1 prototype learning system implemented or learning new postgame analysis heuristic methods iteratively generates and refines the mappings of a set of communicating processes on a computer network. A systematic exploration of the space of possible heuristic methods is shown to promise significant improvement.

  5. QuikForm: Intelligent deformation processing of structural alloys

    Energy Technology Data Exchange (ETDEWEB)

    Bourcier, R.J.; Wellman, G.W.

    1994-09-01

    There currently exists a critical need for tools to enhance the industrial competitiveness and agility of US industries involved in deformation processing of structural alloys. In response to this need, Sandia National Laboratories has embarked upon the QuikForm Initiative. The goal of this program is the development of computer-based tools to facilitate the design of deformation processing operations. The authors are currently focusing their efforts on the definition/development of a comprehensive system for the design of sheet metal stamping operations. The overall structure of the proposed QuikForm system is presented, and the focus of their thrust in each technical area is discussed.

  6. Intelligent workflow driven processing for electronic mail management

    African Journals Online (AJOL)

    Email has become one of the most efficient means of electronics communication for many years and email management has become a critical issue due to congestion. Different client/individuals encounter problems while processing their emails due to large volume of email being received and lot of request to be replied.

  7. Enhancing the Scientific Process with Artificial Intelligence: Forest Science Applications

    Science.gov (United States)

    Ronald E. McRoberts; Daniel L. Schmoldt; H. Michael Rauscher

    1991-01-01

    Forestry, as a science, is a process for investigating nature. It consists of repeatedly cycling through a number of steps, including identifying knowledge gaps, creating knowledge to fill them, and organizing, evaluating, and delivering this knowledge. Much of this effort is directed toward creating abstract models of natural phenomena. The cognitive techniques of AI...

  8. Personality and Information Processing Speed: Independent Influences on Intelligent Performance

    Science.gov (United States)

    Bates, Timothy C.; Rock, Andrew

    2004-01-01

    Raven's matrices and inspection time (IT) were recorded from 56 subjects under five arousal levels. Raven's and IT correlated strongly (r = -0.7) as predicted by processing-speed theories of "g." In line with Eysenck's [Eysenck, H. J. (1967). "The biological basis of personality". Springfield, IL: Thomas] arousal theory of extraversion, there was…

  9. The Use Of Computer Intelligent Processing Technologies Among ...

    African Journals Online (AJOL)

    This paper assesses the awareness and usage of a novel approach to data and information processing among scientists, researchers and students in the field of environmental sciences. In depth and structured interview was conducted, targeting a population who are working in a variety of environmental issues. The data ...

  10. Intelligent process control of fiber chemical vapor deposition

    Science.gov (United States)

    Jones, John Gregory

    Chemical Vapor Deposition (CVD) is a widely used process for the application of thin films. In this case, CVD is being used to apply a thin film interface coating to single crystal monofilament sapphire (Alsb2Osb3) fibers for use in Ceramic Matrix Composites (CMC's). The hot-wall reactor operates at near atmospheric pressure which is maintained using a venturi pump system. Inert gas seals obviate the need for a sealed system. A liquid precursor delivery system has been implemented to provide precise stoichiometry control. Neural networks have been implemented to create real-time process description models trained using data generated based on a Navier-Stokes finite difference model of the process. Automation of the process to include full computer control and data logging capability is also presented. In situ sensors including a quadrupole mass spectrometer, thermocouples, laser scanner, and Raman spectrometer have been implemented to determine the gas phase reactants and coating quality. A fuzzy logic controller has been developed to regulate either the gas phase or the in situ temperature of the reactor using oxygen flow rate as an actuator. Scanning electron microscope (SEM) images of various samples are shown. A hierarchical control structure upon which the control structure is based is also presented.

  11. Software architecture for intelligent image processing using Prolog

    Science.gov (United States)

    Jones, Andrew C.; Batchelor, Bruce G.

    1994-10-01

    We describe a prototype system for interactive image processing using Prolog, implemented by the first author on an Apple Macintosh computer. This system is inspired by Prolog+, but differs from it in two particularly important respects. The first is that whereas Prolog+ assumes the availability of dedicated image processing hardware, with which the Prolog system communicates, our present system implements image processing functions in software using the C programming language. The second difference is that although our present system supports Prolog+ commands, these are implemented in terms of lower-level Prolog predicates which provide a more flexible approach to image manipulation. We discuss the impact of the Apple Macintosh operating system upon the implementation of the image-processing functions, and the interface between these functions and the Prolog system. We also explain how the Prolog+ commands have been implemented. The system described in this paper is a fairly early prototype, and we outline how we intend to develop the system, a task which is expedited by the extensible architecture we have implemented.

  12. 12th International Conference on Intelligent Information Hiding and Multimedia Signal Processing

    CERN Document Server

    Tsai, Pei-Wei; Huang, Hsiang-Cheh

    2017-01-01

    This volume of Smart Innovation, Systems and Technologies contains accepted papers presented in IIH-MSP-2016, the 12th International Conference on Intelligent Information Hiding and Multimedia Signal Processing. The conference this year was technically co-sponsored by Tainan Chapter of IEEE Signal Processing Society, Fujian University of Technology, Chaoyang University of Technology, Taiwan Association for Web Intelligence Consortium, Fujian Provincial Key Laboratory of Big Data Mining and Applications (Fujian University of Technology), and Harbin Institute of Technology Shenzhen Graduate School. IIH-MSP 2016 is held in 21-23, November, 2016 in Kaohsiung, Taiwan. The conference is an international forum for the researchers and professionals in all areas of information hiding and multimedia signal processing. .

  13. Predicting speech intelligibility based on the signal-to-noise envelope power ratio after modulation-frequency selective processing

    DEFF Research Database (Denmark)

    Jørgensen, Søren; Dau, Torsten

    2011-01-01

    A model for predicting the intelligibility of processed noisy speech is proposed. The speech-based envelope power spectrum model has a similar structure as the model of Ewert and Dau [(2000). J. Acoust. Soc. Am. 108, 1181-1196], developed to account for modulation detection and masking data. The ...... process provides a key measure of speech intelligibility. © 2011 Acoustical Society of America.......A model for predicting the intelligibility of processed noisy speech is proposed. The speech-based envelope power spectrum model has a similar structure as the model of Ewert and Dau [(2000). J. Acoust. Soc. Am. 108, 1181-1196], developed to account for modulation detection and masking data....... The model estimates the speech-to-noise envelope power ratio, SNR env, at the output of a modulation filterbank and relates this metric to speech intelligibility using the concept of an ideal observer. Predictions were compared to data on the intelligibility of speech presented in stationary speech...

  14. A Latent Variable Analysis of Working Memory Capacity, Short-Term Memory Capacity, Processing Speed, and General Fluid Intelligence.

    Science.gov (United States)

    Conway, Andrew R. A.; Cowan, Nelsin; Bunting, Michael F.; Therriault, David J.; Minkoff, Scott R. B.

    2002-01-01

    Studied the interrelationships among general fluid intelligence, short-term memory capacity, working memory capacity, and processing speed in 120 young adults and used structural equation modeling to determine the best predictor of general fluid intelligence. Results suggest that working memory capacity, but not short-term memory capacity or…

  15. Influence of Family Processes, Motivation, and Beliefs about Intelligence on Creative Problem Solving of Scientifically Talented Individuals

    Science.gov (United States)

    Cho, Seokhee; Lin, Chia-Yi

    2011-01-01

    Predictive relationships among perceived family processes, intrinsic and extrinsic motivation, incremental beliefs about intelligence, confidence in intelligence, and creative problem-solving practices in mathematics and science were examined. Participants were 733 scientifically talented Korean students in fourth through twelfth grades as well as…

  16. Information processing speed mediates the relationship between white matter and general intelligence in schizophrenia.

    Science.gov (United States)

    Alloza, Clara; Cox, Simon R; Duff, Barbara; Semple, Scott I; Bastin, Mark E; Whalley, Heather C; Lawrie, Stephen M

    2016-08-30

    Several authors have proposed that schizophrenia is the result of impaired connectivity between specific brain regions rather than differences in local brain activity. White matter abnormalities have been suggested as the anatomical substrate for this dysconnectivity hypothesis. Information processing speed may act as a key cognitive resource facilitating higher order cognition by allowing multiple cognitive processes to be simultaneously available. However, there is a lack of established associations between these variables in schizophrenia. We hypothesised that the relationship between white matter and general intelligence would be mediated by processing speed. White matter water diffusion parameters were studied using Tract-based Spatial Statistics and computed within 46 regions-of-interest (ROI). Principal component analysis was conducted on these white matter ROI for fractional anisotropy (FA) and mean diffusivity, and on neurocognitive subtests to extract general factors of white mater structure (gFA, gMD), general intelligence (g) and processing speed (gspeed). There was a positive correlation between g and gFA (r= 0.67, p =0.001) that was partially and significantly mediated by gspeed (56.22% CI: 0.10-0.62). These findings suggest a plausible model of structure-function relations in schizophrenia, whereby white matter structure may provide a neuroanatomical substrate for general intelligence, which is partly supported by speed of information processing. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

  17. Automated business process management – in times of digital transformation using machine learning or artificial intelligence

    Directory of Open Access Journals (Sweden)

    Paschek Daniel

    2017-01-01

    Full Text Available The continuous optimization of business processes is still a challenge for companies. In times of digital transformation, faster changing internal and external framework conditions and new customer expectations for fastest delivery and best quality of goods and many more, companies should set up their internal process at the best way. But what to do if framework conditions changed unexpectedly? The purpose of the paper is to analyse how the digital transformation will impact the Business Process Management (BPM while using methods like machine learning or artificial intelligence. Therefore, the core components will be explained, compared and set up in relation. To identify application areas interviews and analysis will be held up with digital companies. The finding of the paper will be recommendation for action in the field of BPM and process optimization through machine learning and artificial intelligence. The Approach of optimizing and management processes via machine learning and artificial intelligence will support companies to decide which tool will be the best for automated BPM.

  18. Intelligent Optimization of a Mixed Culture Cultivation Process

    Directory of Open Access Journals (Sweden)

    Petia Koprinkova-Hristova

    2015-04-01

    Full Text Available In the present paper a neural network approach called "Adaptive Critic Design" (ACD was applied to optimal tuning of set point controllers of the three main substrates (sugar, nitrogen source and dissolved oxygen for PHB production process. For approximation of the critic and the controllers a special kind of recurrent neural networks called Echo state networks (ESN were used. Their structure allows fast training that will be of crucial importance in on-line applications. The critic network is trained to minimize the temporal difference error using Recursive Least Squares method. Two approaches - gradient and heuristic - were exploited for training of the controllers. The comparison is made with respect to achieved improvement of the utility function subject of optimization as well as with known expert strategy for control the PHB production process.

  19. Improving content marketing processes with the approaches by artificial intelligence

    OpenAIRE

    Kose, Utku; Sert, Selcuk

    2017-01-01

    Content marketing is todays one of the most remarkable approaches in the context of marketing processes of companies. Value of this kind of marketing has improved in time, thanks to the latest developments regarding to computer and communication technologies. Nowadays, especially social media based platforms have a great importance on enabling companies to design multimedia oriented, interactive content. But on the other hand, there is still something more to do for improved content marketing...

  20. Artificial Intelligence for Inferential Control of Crude Oil Stripping Process

    Directory of Open Access Journals (Sweden)

    Mehdi Ebnali

    2018-01-01

    Full Text Available Stripper columns are used for sweetening crude oil, and they must hold product hydrogen sulfide content as near the set points as possible in the faces of upsets. Since product    quality cannot be measured easily and economically online, the control of product quality is often achieved by maintaining a suitable tray temperature near its set point. Tray temperature control method, however, is not a proper option for a multi-component stripping column because the tray temperature does not correspond exactly to the product composition. To overcome this problem, secondary measurements can be used to infer the product quality and adjust the values of the manipulated variables. In this paper, we have used a novel inferential control approach base on adaptive network fuzzy inference system (ANFIS for stripping process. ANFIS with different learning algorithms is used for modeling the process and building a composition estimator to estimate the composition of the bottom product. The developed estimator is tested, and the results show that the predictions made by ANFIS structure are in good agreement with the results of simulation by ASPEN HYSYS process simulation package. In addition, inferential control by the implementation of ANFIS-based online composition estimator in a cascade control scheme is superior to traditional tray temperature control method based on less integral time absolute error and low duty consumption in reboiler.

  1. Suppressive mechanisms in visual motion processing: From perception to intelligence.

    Science.gov (United States)

    Tadin, Duje

    2015-10-01

    Perception operates on an immense amount of incoming information that greatly exceeds the brain's processing capacity. Because of this fundamental limitation, the ability to suppress irrelevant information is a key determinant of perceptual efficiency. Here, I will review a series of studies investigating suppressive mechanisms in visual motion processing, namely perceptual suppression of large, background-like motions. These spatial suppression mechanisms are adaptive, operating only when sensory inputs are sufficiently robust to guarantee visibility. Converging correlational and causal evidence links these behavioral results with inhibitory center-surround mechanisms, namely those in cortical area MT. Spatial suppression is abnormally weak in several special populations, including the elderly and individuals with schizophrenia-a deficit that is evidenced by better-than-normal direction discriminations of large moving stimuli. Theoretical work shows that this abnormal weakening of spatial suppression should result in motion segregation deficits, but direct behavioral support of this hypothesis is lacking. Finally, I will argue that the ability to suppress information is a fundamental neural process that applies not only to perception but also to cognition in general. Supporting this argument, I will discuss recent research that shows individual differences in spatial suppression of motion signals strongly predict individual variations in IQ scores. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

  2. The process of deforestation in weak democracies and the role of Intelligence.

    Science.gov (United States)

    Obydenkova, Anastassia; Nazarov, Zafar; Salahodjaev, Raufhon

    2016-07-01

    This article examines the interconnection between national intelligence, political institutions, and the mismanagement of public resources (deforestations). The paper examines the reasons for deforestation and investigates the factors accountable for it. The analysis builds on authors-compiled cross-national dataset on 185 countries over the time period of twenty years, from 1990 to 2010. We find that, first, nation's intelligence reduces significantly the level of deforestation in a state. Moreover, the nations' IQ seems to play an offsetting role in the natural resource conservation (forest management) in the countries with weak democratic institutions. The analysis also discovered the presence of the U-shaped relationship between democracy and deforestation. Intelligence sheds more light on this interconnection and explains the results. Our results are robust to various sample selection strategies and model specifications. The main implication from our study is that intelligence not only shapes formal rules and informal regulations such as social trust, norms and traditions but also it has the ability to reverse the paradoxical process known as "resource curse." The study contributes to better understanding of reasons of deforestation and shed light on the debated impact of political regime on forest management. Copyright © 2016 Elsevier Inc. All rights reserved.

  3. Recent Technological Advances in Natural Language Processing and Artificial Intelligence

    OpenAIRE

    Shah, Nishal Pradeepkumar

    2012-01-01

    A recent advance in computer technology has permitted scientists to implement and test algorithms that were known from quite some time (or not) but which were computationally expensive. Two such projects are IBM's Jeopardy as a part of its DeepQA project [1] and Wolfram's Wolframalpha[2]. Both these methods implement natural language processing (another goal of AI scientists) and try to answer questions as asked by the user. Though the goal of the two projects is similar, both of them have a ...

  4. 2nd International Symposium on Signal Processing and Intelligent Recognition Systems

    CERN Document Server

    Bandyopadhyay, Sanghamitra; Krishnan, Sri; Li, Kuan-Ching; Mosin, Sergey; Ma, Maode

    2016-01-01

    This Edited Volume contains a selection of refereed and revised papers originally presented at the second International Symposium on Signal Processing and Intelligent Recognition Systems (SIRS-2015), December 16-19, 2015, Trivandrum, India. The program committee received 175 submissions. Each paper was peer reviewed by at least three or more independent referees of the program committee and the 59 papers were finally selected. The papers offer stimulating insights into biometrics, digital watermarking, recognition systems, image and video processing, signal and speech processing, pattern recognition, machine learning and knowledge-based systems. The book is directed to the researchers and scientists engaged in various field of signal processing and related areas. .

  5. An Intelligent System for Modelling, Design and Analysis of Chemical Processes

    DEFF Research Database (Denmark)

    Gani, Rafiqul

    ICAS, Integrated Computer Aided System, is a software that consists of a number of intelligent tools, which are very suitable, among others, for computer aided modelling, sustainable design of chemical and biochemical processes, and design-analysis of product-process monitoring systems. Each...... the computer aided modelling tool will illustrate how to generate a desired process model, how to analyze the model equations, how to extract data and identify the model and make it ready for various types of application. In sustainable process design, the example will highlight the issue of integration...

  6. AMIE Camera System on board SMART-1

    Science.gov (United States)

    Josset, J. L.; Beauvivre, S.; Amie Team

    The Advanced Moon micro-Imager Experiment AMIE on board ESA SMART-1 the first European mission to the Moon launched on 27th September 2003 is an imaging system with scientific technical and public outreach oriented objectives The science objectives are to image the Lunar Poles permanent shadow areas ice deposit eternal light crater rims ancient Lunar Non-mare volcanism local spectro-photometry and physical state of the lunar sur-face and to map high latitudes regions south mainly at far side South Pole Aitken basin The technical objectives are to perform a laserlink experiment detec-tion of laser beam emitted by ESA Tenerife ground station flight demonstration of new technologies and on-board autonomy navigation The public outreach and educational objectives are to promote planetary exploration We present the AMIE instrument and perfomances with respect to the first results

  7. On-boarding the Middle Manager.

    Science.gov (United States)

    OʼConnor, Mary

    The trend of promoting clinical experts into management roles continues. New middle managers need a transitional plan that includes support, mentoring, and direction from senior leaders, including the chief nursing officer (CNO). This case study demonstrates how the CNO of one organization collaborated with a faculty member colleague to develop and implement a yearlong personalized on-boarding program for a group of new nurse middle managers.

  8. Network-Capable Application Process and Wireless Intelligent Sensors for ISHM

    Science.gov (United States)

    Figueroa, Fernando; Morris, Jon; Turowski, Mark; Wang, Ray

    2011-01-01

    Intelligent sensor technology and systems are increasingly becoming attractive means to serve as frameworks for intelligent rocket test facilities with embedded intelligent sensor elements, distributed data acquisition elements, and onboard data acquisition elements. Networked intelligent processors enable users and systems integrators to automatically configure their measurement automation systems for analog sensors. NASA and leading sensor vendors are working together to apply the IEEE 1451 standard for adding plug-and-play capabilities for wireless analog transducers through the use of a Transducer Electronic Data Sheet (TEDS) in order to simplify sensor setup, use, and maintenance, to automatically obtain calibration data, and to eliminate manual data entry and error. A TEDS contains the critical information needed by an instrument or measurement system to identify, characterize, interface, and properly use the signal from an analog sensor. A TEDS is deployed for a sensor in one of two ways. First, the TEDS can reside in embedded, nonvolatile memory (typically flash memory) within the intelligent processor. Second, a virtual TEDS can exist as a separate file, downloadable from the Internet. This concept of virtual TEDS extends the benefits of the standardized TEDS to legacy sensors and applications where the embedded memory is not available. An HTML-based user interface provides a visual tool to interface with those distributed sensors that a TEDS is associated with, to automate the sensor management process. Implementing and deploying the IEEE 1451.1-based Network-Capable Application Process (NCAP) can achieve support for intelligent process in Integrated Systems Health Management (ISHM) for the purpose of monitoring, detection of anomalies, diagnosis of causes of anomalies, prediction of future anomalies, mitigation to maintain operability, and integrated awareness of system health by the operator. It can also support local data collection and storage. This

  9. Women on boards and corporate social responsibility

    Directory of Open Access Journals (Sweden)

    Francesca Gennari

    2016-02-01

    Full Text Available Data by EU Commission show a low representation of women on boards. The scope of this article is to read contemporary and according to a managerial approach the possible causes of this situation: the availability of skills possessed by women to cover top positions, the presence of binding or self-regulatory rules and the corporate culture towards CSR approach. Our research is focused on EU countries, where the gender equality on board is currently matter of attention and regulatory interventions. We conclude that the scarce presence of women in the boardrooms is not ascribable to a scarcity of expertise, but it is associated with a social background and a corporate culture not inspired by corporate global responsibility values. Regulatory interventions may accelerate the consciousness of gender balance on boards, but without companies’ commitment in CSR matters and without a clear vision of corporate global responsibility (including economic, social and environmental aspects, they tend to become additional tasks in the management of corporate compliance risk.

  10. A Feminist Framework for Nurses on Boards.

    Science.gov (United States)

    Sundean, Lisa J; Polifroni, E Carol

    Nurses' knowledge, skills, and expertise uniquely situate them to contribute to health care transformation as equal partners in organizational board governance. The Institute of Medicine, the 10,000 Nurses on Boards Coalition, and a growing number of nurse and health care scholars advocate nurse board leadership; however, nurses are rarely appointed as voting board members. When no room is made for nurses to take a seat at the table, the opportunity is lost to harness the power of nursing knowledge for health care transformation and social justice. No philosophical framework underpins the emerging focus on nurse board leadership. The purpose of this article is to add to the extant nursing literature by suggesting feminism as a philosophical framework for nurses on boards. Feminism contributes to the knowledge base of nursing as it relates to the expanding roles of nurses in health care transformation, policy, and social justice. Furthermore, a feminist philosophical framework for nurses on boards sets the foundation for new theory development and validates ongoing advancement of the nursing profession. Copyright © 2016 Elsevier Inc. All rights reserved.

  11. Advanced Hybrid On-Board Data Processor - SpaceCube 2.0

    Data.gov (United States)

    National Aeronautics and Space Administration — Develop advanced on-board processing to meet the requirements of the Decadal Survey missions: advanced instruments (hyper-spectral, SAR, etc) require advanced...

  12. The use of artificial intelligence techniques to improve the multiple payload integration process

    Science.gov (United States)

    Cutts, Dannie E.; Widgren, Brian K.

    1992-01-01

    A maximum return of science and products with a minimum expenditure of time and resources is a major goal of mission payload integration. A critical component then, in successful mission payload integration is the acquisition and analysis of experiment requirements from the principal investigator and payload element developer teams. One effort to use artificial intelligence techniques to improve the acquisition and analysis of experiment requirements within the payload integration process is described.

  13. USING THE INFORMATION OF ON-BOARD DIAGNOSTIC SYSTEMS IN DETERMINING THE TECHNICAL STATE OF THE LOCOMOTIVE

    Directory of Open Access Journals (Sweden)

    B. Ye. Bodnar

    2008-12-01

    Full Text Available The issues of increase of efficiency of information processing by оn-board systems of diagnostics of locomotives are considered. The examples of information processing by the on-board system of diagnostics of electric locomotives DE1 are presented. The suggestions on improvement of systematization and processing of information by on-board systems of diagnostics are given.

  14. Developing an Intelligent Automatic Appendix Extraction Method from Ultrasonography Based on Fuzzy ART and Image Processing

    Directory of Open Access Journals (Sweden)

    Kwang Baek Kim

    2015-01-01

    Full Text Available Ultrasound examination (US does a key role in the diagnosis and management of the patients with clinically suspected appendicitis which is the most common abdominal surgical emergency. Among the various sonographic findings of appendicitis, outer diameter of the appendix is most important. Therefore, clear delineation of the appendix on US images is essential. In this paper, we propose a new intelligent method to extract appendix automatically from abdominal sonographic images as a basic building block of developing such an intelligent tool for medical practitioners. Knowing that the appendix is located at the lower organ area below the bottom fascia line, we conduct a series of image processing techniques to find the fascia line correctly. And then we apply fuzzy ART learning algorithm to the organ area in order to extract appendix accurately. The experiment verifies that the proposed method is highly accurate (successful in 38 out of 40 cases in extracting appendix.

  15. On-Board Rendezvous Targeting for Orion

    Science.gov (United States)

    Weeks, Michael W.; DSouza, Christopher N.

    2010-01-01

    The Orion On-board GNC system is among the most complex ever developed for a space mission. It is designed to operate autonomously (independent of the ground). The rendezvous system in particular was designed to operate on the far side of the moon, and in the case of loss-of-communications with the ground. The vehicle GNC system is designed to retarget the rendezvous maneuvers, given a mission plan. As such, all the maneuvers which will be performed by Orion, have been designed and are being incorporated into the flight code.

  16. Energy storage on board of railway vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Steiner, M.; Scholten, J. [Bombardier Transportation, Mannheim (Germany)

    2004-07-01

    The proposed energy storage on board of a Railway vehicle leads to a big step in the reduction of consumed energy. Up to 30% energy saving are expected in a light rail vehicle, at the same time reducing the peak power demand drastically. In addition, with the energy storage an operation without catenary could become reality, which was successfully demonstrated with the prototype light rail vehicle driving with switched off pantograph. This prototype vehicle is in passenger operation since September 2003, the implemented software is optimised on energy savings and first experience is very promising. (authors)

  17. Intelligent Processing Equipment Developments Within the Navy's Manufacturing Technology Centers of Excellence

    Science.gov (United States)

    Nanzetta, Philip

    1992-01-01

    The U.S. Navy has had an active Manufacturing Technology (MANTECH) Program aimed at developing advanced production processes and equipment since the late-1960's. During the past decade, however, the resources of the MANTECH program were concentrated in Centers of Excellence. Today, the Navy sponsors four manufacturing technology Centers of Excellence: the Automated Manufacturing Research Facility (AMRF); the Electronics Manufacturing Productivity Facility (EMPF); the National Center for Excellence in Metalworking Technology (NCEMT); and the Center of Excellence for Composites Manufacturing Technology (CECMT). This paper briefly describes each of the centers and summarizes typical Intelligent Equipment Processing (IEP) projects that were undertaken.

  18. Development of a process model for intelligent control of gas metal arc welding

    International Nuclear Information System (INIS)

    Smartt, H.B.; Johnson, J.A.; Einerson, C.J.; Watkins, A.D.; Carlson, N.M.

    1991-01-01

    This paper discusses work in progress on the development of an intelligent control scheme for arc welding. A set of four sensors is used to detect weld bead cooling rate, droplet transfer mode, weld pool and joint location and configuration, and weld defects during welding. A neural network is being developed as the bridge between the multiple sensor set a conventional proportional-integral controller that provides independent control of process variables. This approach is being developed for the gas metal arc welding process. 20 refs., 8 figs

  19. Study on intelligent processing system of man-machine interactive garment frame model

    Science.gov (United States)

    Chen, Shuwang; Yin, Xiaowei; Chang, Ruijiang; Pan, Peiyun; Wang, Xuedi; Shi, Shuze; Wei, Zhongqian

    2018-05-01

    A man-machine interactive garment frame model intelligent processing system is studied in this paper. The system consists of several sensor device, voice processing module, mechanical parts and data centralized acquisition devices. The sensor device is used to collect information on the environment changes brought by the body near the clothes frame model, the data collection device is used to collect the information of the environment change induced by the sensor device, voice processing module is used for speech recognition of nonspecific person to achieve human-machine interaction, mechanical moving parts are used to make corresponding mechanical responses to the information processed by data collection device.it is connected with data acquisition device by a means of one-way connection. There is a one-way connection between sensor device and data collection device, two-way connection between data acquisition device and voice processing module. The data collection device is one-way connection with mechanical movement parts. The intelligent processing system can judge whether it needs to interact with the customer, realize the man-machine interaction instead of the current rigid frame model.

  20. On-board cryogenic system for magnetic levitation of trains

    Energy Technology Data Exchange (ETDEWEB)

    Baldus, S A.W.; Kneuer, R; Stephan, A

    1975-02-01

    An experimental car based on electrodynamic levitation with superconducting magnets was developed and manufactured with an on-board cryogenic system. This system has to cope with new conditions and cryogenic tasks. It can be characterized in principle by liquid helium heat exchanger units, compressors, transfer lines, rotable and movable couplings and junctions. All transfer lines and couplings consist of three coaxial ducts for three different streams. Processes and components are discussed, and a brief description of the first results for the whole system under simulation conditions is given.

  1. On-board cryogenic system for magnetic levitation of trains

    International Nuclear Information System (INIS)

    Asztalos, St.; Baldus, W.; Kneuer, R.; Stephan, A.

    1974-01-01

    An experimental car based on electrodynamic levitation with superconducting magnets has been developed and manufactured by AEG, BBC, Siemens and other partners, together with Linde AG as the firm responsible for the on-board cryogenic system. This system has to cope with new conditions and cryogenic tasks. It can be characterized in principle by liquid helium heat exchanger units, compressors, transfer lines, rotatable and movable couplings and junctions. All transfer lines and couplings consist of three coaxial ducts for three different streams. This paper reports on processes and components. A brief description of the first results for the whole system under simulation conditions is given. (author)

  2. Comparing Binaural Pre-processing Strategies II: Speech Intelligibility of Bilateral Cochlear Implant Users.

    Science.gov (United States)

    Baumgärtel, Regina M; Hu, Hongmei; Krawczyk-Becker, Martin; Marquardt, Daniel; Herzke, Tobias; Coleman, Graham; Adiloğlu, Kamil; Bomke, Katrin; Plotz, Karsten; Gerkmann, Timo; Doclo, Simon; Kollmeier, Birger; Hohmann, Volker; Dietz, Mathias

    2015-12-30

    Several binaural audio signal enhancement algorithms were evaluated with respect to their potential to improve speech intelligibility in noise for users of bilateral cochlear implants (CIs). 50% speech reception thresholds (SRT50) were assessed using an adaptive procedure in three distinct, realistic noise scenarios. All scenarios were highly nonstationary, complex, and included a significant amount of reverberation. Other aspects, such as the perfectly frontal target position, were idealized laboratory settings, allowing the algorithms to perform better than in corresponding real-world conditions. Eight bilaterally implanted CI users, wearing devices from three manufacturers, participated in the study. In all noise conditions, a substantial improvement in SRT50 compared to the unprocessed signal was observed for most of the algorithms tested, with the largest improvements generally provided by binaural minimum variance distortionless response (MVDR) beamforming algorithms. The largest overall improvement in speech intelligibility was achieved by an adaptive binaural MVDR in a spatially separated, single competing talker noise scenario. A no-pre-processing condition and adaptive differential microphones without a binaural link served as the two baseline conditions. SRT50 improvements provided by the binaural MVDR beamformers surpassed the performance of the adaptive differential microphones in most cases. Speech intelligibility improvements predicted by instrumental measures were shown to account for some but not all aspects of the perceptually obtained SRT50 improvements measured in bilaterally implanted CI users. © The Author(s) 2015.

  3. A New Dimension of Business Intelligence: Location-based Intelligence

    OpenAIRE

    Zeljko Panian

    2012-01-01

    Through the course of this paper we define Locationbased Intelligence (LBI) which is outgrowing from process of amalgamation of geolocation and Business Intelligence. Amalgamating geolocation with traditional Business Intelligence (BI) results in a new dimension of BI named Location-based Intelligence. LBI is defined as leveraging unified location information for business intelligence. Collectively, enterprises can transform location data into business intelligence applic...

  4. Development and evaluation of an intelligent traceability system for frozen tilapia fillet processing.

    Science.gov (United States)

    Xiao, Xinqing; Fu, Zetian; Qi, Lin; Mira, Trebar; Zhang, Xiaoshuan

    2015-10-01

    The main export varieties in China are brand-name, high-quality bred aquatic products. Among them, tilapia has become the most important and fast-growing species since extensive consumer markets in North America and Europe have evolved as a result of commodity prices, year-round availability and quality of fresh and frozen products. As the largest tilapia farming country, China has over one-third of its tilapia production devoted to further processing and meeting foreign market demand. Using by tilapia fillet processing, this paper introduces the efforts for developing and evaluating ITS-TF: an intelligent traceability system integrated with statistical process control (SPC) and fault tree analysis (FTA). Observations, literature review and expert questionnaires were used for system requirement and knowledge acquisition; scenario simulation was applied to evaluate and validate ITS-TF performance. The results show that traceability requirement is evolved from a firefighting model to a proactive model for enhancing process management capacity for food safety; ITS-TF transforms itself as an intelligent system to provide functions on early warnings and process management by integrated SPC and FTA. The valuable suggestion that automatic data acquisition and communication technology should be integrated into ITS-TF was achieved for further system optimization, perfection and performance improvement. © 2014 Society of Chemical Industry.

  5. [Is there a physician on board?].

    Science.gov (United States)

    Andersen, H T

    1998-11-01

    Physicians responding to emergency calls on board airliners in intercontinental traffic may not be aware of certain legal complications which may arise. For instance, the medical practitioner may hold a license valid in one country, the air carrier may be registered in another, and the patient may be a third state national. Legislation varies between nations, as do court decisions. Physicians may be aware neither of the laws and regulations which apply nor the subtle differences between terms and interpretations used in formal language. This article contains a scenario description from a commercial air liner in intercontinental transit carrying a patient unknown to the physician who responds to a call for medical assistance. The main considerations to be made, the more likely diagnoses and various strategies for immediate interventions are reviewed. Likewise, appraisal and use of medical equipment on board are discussed, as are issues concerning responsibility and liability when equipment is used in supposedly "trained hands". Main themes in the current international medico-legal debate are considered with emphasis on the "Good Samaritan Principle", the responsibility of commercial air carriers, and telemedicine with insurance against law suits. The article concludes with some practical advice to the travelling medical community.

  6. An intelligent approach for cooling radiator fault diagnosis based on infrared thermal image processing technique

    International Nuclear Information System (INIS)

    Taheri-Garavand, Amin; Ahmadi, Hojjat; Omid, Mahmoud; Mohtasebi, Seyed Saeid; Mollazade, Kaveh; Russell Smith, Alan John; Carlomagno, Giovanni Maria

    2015-01-01

    This research presents a new intelligent fault diagnosis and condition monitoring system for classification of different conditions of cooling radiator using infrared thermal images. The system was adopted to classify six types of cooling radiator faults; radiator tubes blockage, radiator fins blockage, loose connection between fins and tubes, radiator door failure, coolant leakage, and normal conditions. The proposed system consists of several distinct procedures including thermal image acquisition, image pre-processing, image processing, two-dimensional discrete wavelet transform (2D-DWT), feature extraction, feature selection using a genetic algorithm (GA), and finally classification by artificial neural networks (ANNs). The 2D-DWT is implemented to decompose the thermal images. Subsequently, statistical texture features are extracted from the original images and are decomposed into thermal images. The significant selected features are used to enhance the performance of the designed ANN classifier for the 6 types of cooling radiator conditions (output layer) in the next stage. For the tested system, the input layer consisted of 16 neurons based on the feature selection operation. The best performance of ANN was obtained with a 16-6-6 topology. The classification results demonstrated that this system can be employed satisfactorily as an intelligent condition monitoring and fault diagnosis for a class of cooling radiator. - Highlights: • Intelligent fault diagnosis of cooling radiator using thermal image processing. • Thermal image processing in a multiscale representation structure by 2D-DWT. • Selection features based on a hybrid system that uses both GA and ANN. • Application of ANN as classifier. • Classification accuracy of fault detection up to 93.83%

  7. Working memory - not processing speed - mediates fluid intelligence deficits associated with attention deficit/hyperactivity disorder symptoms.

    Science.gov (United States)

    Brydges, Christopher R; Ozolnieks, Krista L; Roberts, Gareth

    2017-09-01

    Attention deficit/hyperactivity disorder (ADHD) is a psychological condition characterized by inattention and hyperactivity. Cognitive deficits are commonly observed in ADHD patients, including impaired working memory, processing speed, and fluid intelligence, the three of which are theorized to be closely associated with one another. In this study, we aimed to determine if decreased fluid intelligence was associated with ADHD, and was mediated by deficits in working memory and processing speed. This study tested 142 young adults from the general population on a range of working memory, processing speed, and fluid intelligence tasks, and an ADHD self-report symptoms questionnaire. Results showed that total and hyperactive ADHD symptoms correlated significantly and negatively with fluid intelligence, but this association was fully mediated by working memory. However, inattentive symptoms were not associated with fluid intelligence. Additionally, processing speed was not associated with ADHD symptoms at all, and was not uniquely predictive of fluid intelligence. The results provide implications for working memory training programs for ADHD patients, and highlight potential differences between the neuropsychological profiles of ADHD subtypes. © 2015 The British Psychological Society.

  8. Optimization process planning using hybrid genetic algorithm and intelligent search for job shop machining.

    Science.gov (United States)

    Salehi, Mojtaba; Bahreininejad, Ardeshir

    2011-08-01

    Optimization of process planning is considered as the key technology for computer-aided process planning which is a rather complex and difficult procedure. A good process plan of a part is built up based on two elements: (1) the optimized sequence of the operations of the part; and (2) the optimized selection of the machine, cutting tool and Tool Access Direction (TAD) for each operation. In the present work, the process planning is divided into preliminary planning, and secondary/detailed planning. In the preliminary stage, based on the analysis of order and clustering constraints as a compulsive constraint aggregation in operation sequencing and using an intelligent searching strategy, the feasible sequences are generated. Then, in the detailed planning stage, using the genetic algorithm which prunes the initial feasible sequences, the optimized operation sequence and the optimized selection of the machine, cutting tool and TAD for each operation based on optimization constraints as an additive constraint aggregation are obtained. The main contribution of this work is the optimization of sequence of the operations of the part, and optimization of machine selection, cutting tool and TAD for each operation using the intelligent search and genetic algorithm simultaneously.

  9. Artificial Intelligence.

    Science.gov (United States)

    Wash, Darrel Patrick

    1989-01-01

    Making a machine seem intelligent is not easy. As a consequence, demand has been rising for computer professionals skilled in artificial intelligence and is likely to continue to go up. These workers develop expert systems and solve the mysteries of machine vision, natural language processing, and neural networks. (Editor)

  10. Event Detection Intelligent Camera: Demonstration of flexible, real-time data taking and processing

    Energy Technology Data Exchange (ETDEWEB)

    Szabolics, Tamás, E-mail: szabolics.tamas@wigner.mta.hu; Cseh, Gábor; Kocsis, Gábor; Szepesi, Tamás; Zoletnik, Sándor

    2015-10-15

    Highlights: • We present EDICAM's operation principles description. • Firmware tests results. • Software test results. • Further developments. - Abstract: An innovative fast camera (EDICAM – Event Detection Intelligent CAMera) was developed by MTA Wigner RCP in the last few years. This new concept was designed for intelligent event driven processing to be able to detect predefined events and track objects in the plasma. The camera provides a moderate frame rate of 400 Hz at full frame resolution (1280 × 1024), and readout of smaller region of interests can be done in the 1–140 kHz range even during exposure of the full image. One of the most important advantages of this hardware is a 10 Gbit/s optical link which ensures very fast communication and data transfer between the PC and the camera, enabling two level of processing: primitive algorithms in the camera hardware and high-level processing in the PC. This camera hardware has successfully proven to be able to monitoring the plasma in several fusion devices for example at ASDEX Upgrade, KSTAR and COMPASS with the first version of firmware. A new firmware and software package is under development. It allows to detect predefined events in real time and therefore the camera is capable to change its own operation or to give warnings e.g. to the safety system of the experiment. The EDICAM system can handle a huge amount of data (up to TBs) with high data rate (950 MB/s) and will be used as the central element of the 10 camera overview video diagnostic system of Wendenstein 7-X (W7-X) stellarator. This paper presents key elements of the newly developed built-in intelligence stressing the revolutionary new features and the results of the test of the different software elements.

  11. The Virtual UNICOS Process Expert: integration of Artificial Intelligence tools in Control Systems

    CERN Multimedia

    Vilches Calvo, I; Barillere, R

    2009-01-01

    UNICOS is a CERN framework to produce control applications. It provides operators with ways to interact with all process items from the most simple (e.g. I/O channels) to the most abstract objects (e.g. a part of the plant). This possibility of fine grain operation is particularly useful to recover from abnormal situations if operators have the required knowledge. The Virtual UNICOS Process Expert project aims at providing operators with means to handle difficult operation cases for which the intervention of process experts is usually requested. The main idea of project is to use the openness of the UNICOS-based applications to integrate tools (e.g. Artificial Intelligence tools) which will act as Process Experts to analyze complex situations, to propose and to execute smooth recovery procedures.

  12. Gaussian process based intelligent sampling for measuring nano-structure surfaces

    Science.gov (United States)

    Sun, L. J.; Ren, M. J.; Yin, Y. H.

    2016-09-01

    Nanotechnology is the science and engineering that manipulate matters at nano scale, which can be used to create many new materials and devices with a vast range of applications. As the nanotech product increasingly enters the commercial marketplace, nanometrology becomes a stringent and enabling technology for the manipulation and the quality control of the nanotechnology. However, many measuring instruments, for instance scanning probe microscopy, are limited to relatively small area of hundreds of micrometers with very low efficiency. Therefore some intelligent sampling strategies should be required to improve the scanning efficiency for measuring large area. This paper presents a Gaussian process based intelligent sampling method to address this problem. The method makes use of Gaussian process based Bayesian regression as a mathematical foundation to represent the surface geometry, and the posterior estimation of Gaussian process is computed by combining the prior probability distribution with the maximum likelihood function. Then each sampling point is adaptively selected by determining the position which is the most likely outside of the required tolerance zone among the candidates and then inserted to update the model iteratively. Both simulationson the nominal surface and manufactured surface have been conducted on nano-structure surfaces to verify the validity of the proposed method. The results imply that the proposed method significantly improves the measurement efficiency in measuring large area structured surfaces.

  13. Cognitive Processing Speed, Working Memory, and the Intelligibility of Hearing Aid-Processed Speech in Persons with Hearing Impairment

    Directory of Open Access Journals (Sweden)

    Wycliffe Kabaywe Yumba

    2017-08-01

    Full Text Available Previous studies have demonstrated that successful listening with advanced signal processing in digital hearing aids is associated with individual cognitive capacity, particularly working memory capacity (WMC. This study aimed to examine the relationship between cognitive abilities (cognitive processing speed and WMC and individual listeners’ responses to digital signal processing settings in adverse listening conditions. A total of 194 native Swedish speakers (83 women and 111 men, aged 33–80 years (mean = 60.75 years, SD = 8.89, with bilateral, symmetrical mild to moderate sensorineural hearing loss who had completed a lexical decision speed test (measuring cognitive processing speed and semantic word-pair span test (SWPST, capturing WMC participated in this study. The Hagerman test (capturing speech recognition in noise was conducted using an experimental hearing aid with three digital signal processing settings: (1 linear amplification without noise reduction (NoP, (2 linear amplification with noise reduction (NR, and (3 non-linear amplification without NR (“fast-acting compression”. The results showed that cognitive processing speed was a better predictor of speech intelligibility in noise, regardless of the types of signal processing algorithms used. That is, there was a stronger association between cognitive processing speed and NR outcomes and fast-acting compression outcomes (in steady state noise. We observed a weaker relationship between working memory and NR, but WMC did not relate to fast-acting compression. WMC was a relatively weaker predictor of speech intelligibility in noise. These findings might have been different if the participants had been provided with training and or allowed to acclimatize to binary masking noise reduction or fast-acting compression.

  14. Research on application of intelligent computation based LUCC model in urbanization process

    Science.gov (United States)

    Chen, Zemin

    2007-06-01

    Global change study is an interdisciplinary and comprehensive research activity with international cooperation, arising in 1980s, with the largest scopes. The interaction between land use and cover change, as a research field with the crossing of natural science and social science, has become one of core subjects of global change study as well as the front edge and hot point of it. It is necessary to develop research on land use and cover change in urbanization process and build an analog model of urbanization to carry out description, simulation and analysis on dynamic behaviors in urban development change as well as to understand basic characteristics and rules of urbanization process. This has positive practical and theoretical significance for formulating urban and regional sustainable development strategy. The effect of urbanization on land use and cover change is mainly embodied in the change of quantity structure and space structure of urban space, and LUCC model in urbanization process has been an important research subject of urban geography and urban planning. In this paper, based upon previous research achievements, the writer systematically analyzes the research on land use/cover change in urbanization process with the theories of complexity science research and intelligent computation; builds a model for simulating and forecasting dynamic evolution of urban land use and cover change, on the basis of cellular automation model of complexity science research method and multi-agent theory; expands Markov model, traditional CA model and Agent model, introduces complexity science research theory and intelligent computation theory into LUCC research model to build intelligent computation-based LUCC model for analog research on land use and cover change in urbanization research, and performs case research. The concrete contents are as follows: 1. Complexity of LUCC research in urbanization process. Analyze urbanization process in combination with the contents

  15. Work process and task-based design of intelligent assistance systems in German textile industry

    Science.gov (United States)

    Löhrer, M.; Ziesen, N.; Altepost, A.; Saggiomo, M.; Gloy, Y. S.

    2017-10-01

    The mid-sized embossed German textile industry must face social challenges e.g. demographic change or technical changing processes. Interaction with intelligent systems (on machines) and increasing automation changes processes, working structures and employees’ tasks on all levels. Work contents are getting more complex, resulting in the necessity for diversified and enhanced competencies. Mobile devices like tablets or smartphones are increasingly finding their way into the workplace. Employees who grew up with new forms of media have certain advantages regarding the usage of modern technologies compared to older employees. Therefore, it is necessary to design new systems which help to adapt the competencies of both younger and older employees to new automated production processes in the digital work environment. The key to successful integration of technical assistance systems is user-orientated design and development that includes concepts for competency development under consideration of, e.g., ethical and legal aspects.

  16. The research of new type stratified water injection process intelligent measurement technology

    Science.gov (United States)

    Zhao, Xin

    2017-10-01

    To meet the needs of injection and development of Daqing Oilfield, the injection of oil from the early stage of general water injection to the subdivision of water is the purpose of improving the utilization degree and the qualified rate of water injection, improving the performance of water injection column and the matching process. Sets of suitable for high water content of the effective water injection technology supporting technology. New layered water injection technology intelligent measurement technology will be more information testing and flow control combined into a unified whole, long-term automatic monitoring of the work of the various sections, in the custom The process has the characteristics of "multi-layer synchronous measurement, continuous monitoring of process parameters, centralized admission data", which can meet the requirement of subdivision water injection, but also realize the automatic synchronization measurement of each interval, greatly improve the efficiency of tiered injection wells to provide a new means for the remaining oil potential.

  17. Political and Budgetary Oversight of the Ukrainian Intelligence Community: Processes, Problems and Prospects for Reform

    National Research Council Canada - National Science Library

    Petrov, Oleksii

    2007-01-01

    .... Official government documents, news reports and other literature on the intelligence system in Ukraine, as well as studies of intelligence oversight within democracies are the primary sources of data...

  18. On-board attitude determination for the Explorer Platform satellite

    Science.gov (United States)

    Jayaraman, C.; Class, B.

    1992-01-01

    This paper describes the attitude determination algorithm for the Explorer Platform satellite. The algorithm, which is baselined on the Landsat code, is a six-element linear quadratic state estimation processor, in the form of a Kalman filter augmented by an adaptive filter process. Improvements to the original Landsat algorithm were required to meet mission pointing requirements. These consisted of a more efficient sensor processing algorithm and the addition of an adaptive filter which acts as a check on the Kalman filter during satellite slew maneuvers. A 1750A processor will be flown on board the satellite for the first time as a coprocessor (COP) in addition to the NASA Standard Spacecraft Computer. The attitude determination algorithm, which will be resident in the COP's memory, will make full use of its improved processing capabilities to meet mission requirements. Additional benefits were gained by writing the attitude determination code in Ada.

  19. A Spatially Intelligent Public Participation System for the Environmental Impact Assessment Process

    Directory of Open Access Journals (Sweden)

    Lei Lei

    2013-05-01

    Full Text Available An environmental impact assessment (EIA is a decision-making process that evaluates the possible significant effects that a proposed project may exert on the environment. The EIA scoping and reviewing stages often involve public participation. Although its importance has long been recognized, public participation in the EIA process is often regarded as ineffective, due to time, budget, resource, technical and procedural constraints, as well as the complexity of environmental information. Geographic Information System (GIS and Volunteer Geographic Information (VGI have the potential to contribute to data collection, sharing and presentation, utilize local user-generated content to benefit decision-making and increase public outreach. This research integrated GIS, VGI, social media tools, data mining and mobile technology to design a spatially intelligent framework that presented and shared EIA information effectively to the public. A spatially intelligent public participative system (SIPPS was also developed as a proof-of-concept of the framework. The research selected the Tehachapi Renewable Transmission Project (TRTP as the pilot study area. Survey questionnaires were designed to collect feedback and conduct evaluation. Results show that SIPPS was able to improve the effectiveness of public participation, promote environmental awareness and achieve good system usability.

  20. Reactive Goal Decomposition Hierarchies for On-Board Autonomy

    Science.gov (United States)

    Hartmann, L.

    2002-01-01

    to state and environment and in general can terminate the execution of a decomposition and attempt a new decomposition at any level in the hierarchy. This goal decomposition system is suitable for workstation, microprocessor and fpga implementation and thus is able to support the full range of prototyping activities, from mission design in the laboratory to development of the fpga firmware for the flight system. This approach is based on previous artificial intelligence work including (1) Brooks' subsumption architecture for robot control, (2) Firby's Reactive Action Package System (RAPS) for mediating between high level automated planning and low level execution and (3) hierarchical task networks for automated planning. Reactive goal decomposition hierarchies can be used for a wide variety of on-board autonomy applications including automating low level operation sequences (such as scheduling prerequisite operations, e.g., heaters, warm-up periods, monitoring power constraints), coordinating multiple spacecraft as in formation flying and constellations, robot manipulator operations, rendez-vous, docking, servicing, assembly, on-orbit maintenance, planetary rover operations, solar system and interstellar probes, intelligent science data gathering and disaster early warning. Goal decomposition hierarchies can support high level fault tolerance. Given models of on-board resources and goals to accomplish, the decomposition hierarchy could allocate resources to goals taking into account existing faults and in real-time reallocating resources as new faults arise. Resources to be modeled include memory (e.g., ROM, FPGA configuration memory, processor memory, payload instrument memory), processors, on-board and interspacecraft network nodes and links, sensors, actuators (e.g., attitude determination and control, guidance and navigation) and payload instruments. A goal decomposition hierarchy could be defined to map mission goals and tasks to available on-board resources. As

  1. Open-source intelligence in the Czech military knowledge syst em and process design

    OpenAIRE

    Krejci, Roman

    2002-01-01

    Owing to the recent transitions in the Czech Republic, the Czech military must satisfy a large set of new requirements. One way the military intelligence can become more effective and can conserve resources is by increasing the efficiency of open-source intelligence (OSINT), which plays an important part in intelligence gathering in the age of information. When using OSINT effectively, the military intelligence can elevate its responsiveness to different types of crises and can also properly ...

  2. Study of an intelligent system for wells elevation and petroliferous processes control; Estudo de um sistema inteligente para elevacao de pocos e controle de processos petroliferos

    Energy Technology Data Exchange (ETDEWEB)

    Patricio, Antonio Rodrigues

    1996-11-01

    The petroleum production problems were studied by means of an integrated process evaluation of a rod pumping well, a gas lift well and a process until for produced fluids. Using the artificial intelligent concepts as fuzzy logic and neural systems is presented SIEP, An Intelligent for Production Lift and Process Control, aimed to do the integrated management of the petroleum production process. (author)

  3. Emotional Intelligence Tests: Potential Impacts on the Hiring Process for Accounting Students

    Science.gov (United States)

    Nicholls, Shane; Wegener, Matt; Bay, Darlene; Cook, Gail Lynn

    2012-01-01

    Emotional intelligence is increasingly recognized as being important for professional career success. Skills related to emotional intelligence (e.g. organizational commitment, public speaking, teamwork, and leadership) are considered essential. Human resource professionals have begun including tests of emotional intelligence (EI) in job applicant…

  4. On-board data management study for EOPAP

    Science.gov (United States)

    Davisson, L. D.

    1975-01-01

    The requirements, implementation techniques, and mission analysis associated with on-board data management for EOPAP were studied. SEASAT-A was used as a baseline, and the storage requirements, data rates, and information extraction requirements were investigated for each of the following proposed SEASAT sensors: a short pulse 13.9 GHz radar, a long pulse 13.9 GHz radar, a synthetic aperture radar, a multispectral passive microwave radiometer facility, and an infrared/visible very high resolution radiometer (VHRR). Rate distortion theory was applied to determine theoretical minimum data rates and compared with the rates required by practical techniques. It was concluded that practical techniques can be used which approach the theoretically optimum based upon an empirically determined source random process model. The results of the preceding investigations were used to recommend an on-board data management system for (1) data compression through information extraction, optimal noiseless coding, source coding with distortion, data buffering, and data selection under command or as a function of data activity, (2) for command handling, (3) for spacecraft operation and control, and (4) for experiment operation and monitoring.

  5. Intelligent monitoring and fault diagnosis for ATLAS TDAQ: a complex event processing solution

    CERN Document Server

    Magnoni, Luca; Luppi, Eleonora

    Effective monitoring and analysis tools are fundamental in modern IT infrastructures to get insights on the overall system behavior and to deal promptly and effectively with failures. In recent years, Complex Event Processing (CEP) technologies have emerged as effective solutions for information processing from the most disparate fields: from wireless sensor networks to financial analysis. This thesis proposes an innovative approach to monitor and operate complex and distributed computing systems, in particular referring to the ATLAS Trigger and Data Acquisition (TDAQ) system currently in use at the European Organization for Nuclear Research (CERN). The result of this research, the AAL project, is currently used to provide ATLAS data acquisition operators with automated error detection and intelligent system analysis. The thesis begins by describing the TDAQ system and the controlling architecture, with a focus on the monitoring infrastructure and the expert system used for error detection and automated reco...

  6. The Viewpoint Paradigm: a semiotic based approach for the intelligibility of a cooperative designing process

    Directory of Open Access Journals (Sweden)

    Pierre-Jean Charrel

    2002-11-01

    Full Text Available The concept of viewpoint is studied in the field of the modelling and the knowledge management concerned in the upstream phases of a designing process. The concept is approached by semiotics, i.e. in dealing with the requirements so that an actor gives sense to an object. This gives means to transform the intuitive concepts of viewpoint and relation between viewpoints into the Viewpoint Paradigm: the sense of an object is the integration of the viewpoints which exert on it. The elements of this paradigm are integrated in a general model, which defines two concepts formally: Viewpoint and Correlation of viewpoints. The Viewpoint Paradigm is then implemented in operational concerns which are related with the intelligibility of the designing process. Two models of viewpoint and correlation are proposed. They raise of viewpoints management such as one can identify them in the written documents of a project.

  7. IBIS: the imager on-board integral

    International Nuclear Information System (INIS)

    Ubertini, P.; Bazzano, A.; Lebrun, F.; Goldwurm, A.; Laurent, P.; Mirabel, I.F.; Vigroux, L.; Di Cocco, G.; Labanti, C.; Bird, A.J.; Broenstad, K.; La Rosa, G.; Sacco, B.; Quadrini, E.M.; Ramsey, B.; Weisskopf, M.C.; Reglero, V.; Sabau, L.; Staubert, R.; Zdziarski, A.A.

    2003-01-01

    The IBIS telescope is the high angular resolution gamma-ray imager on-board the INTEGRAL Observatory, successfully launched from Baikonur (Kazakhstan) on October 2002. This medium size ESA project, planned for a 2 year mission with possible extension to 5, is devoted to the observation of the gamma-ray sky in the energy range from 3 keV to 10 MeV (Winkler 2001). The IBIS imaging system is based on two independent solid state detector arrays optimised for low (15-1000 keV) and high (0.175-10.0 MeV) energies surrounded by an active VETO System. This high efficiency shield is essential to minimise the background induced by high energy particles in the highly ex-centric out of van Allen belt orbit. A Tungsten Coded Aperture Mask, 16 mm thick and ∼ 1 squared meter in dimension is the imaging device. The IBIS telescope will serve the scientific community at large providing a unique combination of unprecedented high energy wide field imaging capability coupled with broad band spectroscopy and high resolution timing over the energy range from X to gamma rays. To date the IBIS telescope is working nominally in orbit since more than 9 month. (authors)

  8. Energy-efficient hierarchical processing in the network of wireless intelligent sensors (WISE)

    Science.gov (United States)

    Raskovic, Dejan

    Sensor network nodes have benefited from technological advances in the field of wireless communication, processing, and power sources. However, the processing power of microcontrollers is often not sufficient to perform sophisticated processing, while the power requirements of digital signal processing boards or handheld computers are usually too demanding for prolonged system use. We are matching the intrinsic hierarchical nature of many digital signal-processing applications with the natural hierarchy in distributed wireless networks, and building the hierarchical system of wireless intelligent sensors. Our goal is to build a system that will exploit the hierarchical organization to optimize the power consumption and extend battery life for the given time and memory constraints, while providing real-time processing of sensor signals. In addition, we are designing our system to be able to adapt to the current state of the environment, by dynamically changing the algorithm through procedure replacement. This dissertation presents the analysis of hierarchical environment and methods for energy profiling used to evaluate different system design strategies, and to optimize time-effective and energy-efficient processing.

  9. An Integrated Open Approach to Capturing Systematic Knowledge for Manufacturing Process Innovation Based on Collective Intelligence

    Directory of Open Access Journals (Sweden)

    Gangfeng Wang

    2018-02-01

    Full Text Available Process innovation plays a vital role in the manufacture realization of increasingly complex new products, especially in the context of sustainable development and cleaner production. Knowledge-based innovation design can inspire designers’ creative thinking; however, the existing scattered knowledge has not yet been properly captured and organized according to Computer-Aided Process Innovation (CAPI. Therefore, this paper proposes an integrated approach to tackle this non-trivial issue. By analyzing the design process of CAPI and technical features of open innovation, a novel holistic paradigm of process innovation knowledge capture based on collective intelligence (PIKC-CI is constructed from the perspective of the knowledge life cycle. Then, a multi-source innovation knowledge fusion algorithm based on semantic elements reconfiguration is applied to form new public knowledge. To ensure the credibility and orderliness of innovation knowledge refinement, a collaborative editing strategy based on knowledge lock and knowledge–social trust degree is explored. Finally, a knowledge management system MPI-OKCS integrating the proposed techniques is implemented into the pre-built CAPI general platform, and a welding process innovation example is provided to illustrate the feasibility of the proposed approach. It is expected that our work would lay the foundation for the future knowledge-inspired CAPI and smart process planning.

  10. A study on the real-time reliability of on-board equipment of train control system

    Science.gov (United States)

    Zhang, Yong; Li, Shiwei

    2018-05-01

    Real-time reliability evaluation is conducive to establishing a condition based maintenance system for the purpose of guaranteeing continuous train operation. According to the inherent characteristics of the on-board equipment, the connotation of reliability evaluation of on-board equipment is defined and the evaluation index of real-time reliability is provided in this paper. From the perspective of methodology and practical application, the real-time reliability of the on-board equipment is discussed in detail, and the method of evaluating the realtime reliability of on-board equipment at component level based on Hidden Markov Model (HMM) is proposed. In this method the performance degradation data is used directly to realize the accurate perception of the hidden state transition process of on-board equipment, which can achieve a better description of the real-time reliability of the equipment.

  11. ECG Signal Processing, Classification and Interpretation A Comprehensive Framework of Computational Intelligence

    CERN Document Server

    Pedrycz, Witold

    2012-01-01

    Electrocardiogram (ECG) signals are among the most important sources of diagnostic information in healthcare so improvements in their analysis may also have telling consequences. Both the underlying signal technology and a burgeoning variety of algorithms and systems developments have proved successful targets for recent rapid advances in research. ECG Signal Processing, Classification and Interpretation shows how the various paradigms of Computational Intelligence, employed either singly or in combination, can produce an effective structure for obtaining often vital information from ECG signals. Neural networks do well at capturing the nonlinear nature of the signals, information granules realized as fuzzy sets help to confer interpretability on the data and evolutionary optimization may be critical in supporting the structural development of ECG classifiers and models of ECG signals. The contributors address concepts, methodology, algorithms, and case studies and applications exploiting the paradigm of Comp...

  12. Argumentative SOX Compliant and Quality Decision Support Intelligent Expert System over the Suppliers Selection Process

    Directory of Open Access Journals (Sweden)

    Jesus Angel Fernandez Canelas

    2013-01-01

    Full Text Available The objective of this paper is to define a decision support system over SOX (Sarbanes-Oxley Act compatibility and quality of the Suppliers Selection Process based on Artificial Intelligence and Argumentation Theory knowledge and techniques. The present SOX Law, in effect nowadays, was created to improve financial government control over US companies. This law is a factor standard out United States due to several factors like present globalization, expansion of US companies, or key influence of US stock exchange markets worldwide. This paper constitutes a novel approach to this kind of problems due to following elements: (1 it has an optimized structure to look for the solution, (2 it has a dynamic learning method to handle court and control gonvernment bodies decisions, (3 it uses fuzzy knowledge to improve its performance, and (4 it uses its past accumulated experience to let the system evolve far beyond its initial state.

  13. Study on robot motion control for intelligent welding processes based on the laser tracking sensor

    Science.gov (United States)

    Zhang, Bin; Wang, Qian; Tang, Chen; Wang, Ju

    2017-06-01

    A robot motion control method is presented for intelligent welding processes of complex spatial free-form curve seams based on the laser tracking sensor. First, calculate the tip position of the welding torch according to the velocity of the torch and the seam trajectory detected by the sensor. Then, search the optimal pose of the torch under constraints using genetic algorithms. As a result, the intersection point of the weld seam and the laser plane of the sensor is within the detectable range of the sensor. Meanwhile, the angle between the axis of the welding torch and the tangent of the weld seam meets the requirements. The feasibility of the control method is proved by simulation.

  14. Development of an intelligent CAI system for a distributed processing environment

    International Nuclear Information System (INIS)

    Fujii, M.; Sasaki, K.; Ohi, T.; Itoh, T.

    1993-01-01

    In order to operate a nuclear power plant optimally in both normal and abnormal situations, the operators are trained using an operator training simulator in addition to classroom instruction. Individual instruction using a CAI (Computer-Assisted Instruction) system has become popular as a method of learning plant information, such as plant dynamics, operational procedures, plant systems, plant facilities, etc. The outline is described of a proposed network-based intelligent CAI system (ICAI) incorporating multi-medial PWR plant dynamics simulation, teaching aids and educational record management using the following environment: existing standard workstations and graphic workstations with a live video processing function, TCP/IP protocol of Unix through Ethernet and X window system. (Z.S.) 3 figs., 2 refs

  15. Intelligent Processing Equipment Research and Development Programs of the Department of Commerce

    Science.gov (United States)

    Simpson, J. A.

    1992-01-01

    The intelligence processing equipment (IPE) research and development (R&D) programs of the Department of Commerce are carried out within the National Institute of Standards and Technology (NIST). This institute has had work in support of industrial productivity as part of its mission since its founding in 1901. With the advent of factory automation these efforts have increasingly turned to R&D in IPE. The Manufacturing Engineering Laboratory (MEL) of NIST devotes a major fraction of its efforts to this end while other elements within the organization, notably the Material Science and Engineering Laboratory, have smaller but significant programs. An inventory of all such programs at NIST and a representative selection of projects that at least demonstrate the scope of the efforts are presented.

  16. Service with a smile: do emotional intelligence, gender, and autonomy moderate the emotional labor process?

    Science.gov (United States)

    Johnson, Hazel-Anne M; Spector, Paul E

    2007-10-01

    This survey study of 176 participants from eight customer service organizations investigated how individual factors moderate the impact of emotional labor strategies on employee well-being. Hierarchical regression analyses indicated that gender and autonomy were significant moderators of the relationships between emotional labor strategies and the personal outcomes of emotional exhaustion, affective well-being, and job satisfaction. Females were more likely to experience negative consequences when engaging in surface acting. Autonomy served to alleviate negative outcomes for individuals who used emotional labor strategies often. Contrary to our hypotheses, emotional intelligence did not moderate the relationship between the emotional labor strategies and personal outcomes. Results demonstrated how the emotional labor process can influence employee well-being. (c) 2007 APA, all rights reserved.

  17. The Relationship between Emotional Intelligence and Cool and Hot Cognitive Processes: A Systematic Review

    Science.gov (United States)

    Gutiérrez-Cobo, María José; Cabello, Rosario; Fernández-Berrocal, Pablo

    2016-01-01

    Although emotion and cognition were considered to be separate aspects of the psyche in the past, researchers today have demonstrated the existence of an interplay between the two processes. Emotional intelligence (EI), or the ability to perceive, use, understand, and regulate emotions, is a relatively young concept that attempts to connect both emotion and cognition. While EI has been demonstrated to be positively related to well-being, mental and physical health, and non-aggressive behaviors, little is known about its underlying cognitive processes. The aim of the present study was to systematically review available evidence about the relationship between EI and cognitive processes as measured through “cool” (i.e., not emotionally laden) and “hot” (i.e., emotionally laden) laboratory tasks. We searched Scopus and Medline to find relevant articles in Spanish and English, and divided the studies following two variables: cognitive processes (hot vs. cool) and EI instruments used (performance-based ability test, self-report ability test, and self-report mixed test). We identified 26 eligible studies. The results provide a fair amount of evidence that performance-based ability EI (but not self-report EI tests) is positively related with efficiency in hot cognitive tasks. EI, however, does not appear to be related with cool cognitive tasks: neither through self-reporting nor through performance-based ability instruments. These findings suggest that performance-based ability EI could improve individuals’ emotional information processing abilities. PMID:27303277

  18. An Intelligent Complex Event Processing with D Numbers under Fuzzy Environment

    Directory of Open Access Journals (Sweden)

    Fuyuan Xiao

    2016-01-01

    Full Text Available Efficient matching of incoming mass events to persistent queries is fundamental to complex event processing systems. Event matching based on pattern rule is an important feature of complex event processing engine. However, the intrinsic uncertainty in pattern rules which are predecided by experts increases the difficulties of effective complex event processing. It inevitably involves various types of the intrinsic uncertainty, such as imprecision, fuzziness, and incompleteness, due to the inability of human beings subjective judgment. Nevertheless, D numbers is a new mathematic tool to model uncertainty, since it ignores the condition that elements on the frame must be mutually exclusive. To address the above issues, an intelligent complex event processing method with D numbers under fuzzy environment is proposed based on the Technique for Order Preferences by Similarity to an Ideal Solution (TOPSIS method. The novel method can fully support decision making in complex event processing systems. Finally, a numerical example is provided to evaluate the efficiency of the proposed method.

  19. Artificial Intelligence Tools for Scaling Up of High Shear Wet Granulation Process.

    Science.gov (United States)

    Landin, Mariana

    2017-01-01

    The results presented in this article demonstrate the potential of artificial intelligence tools for predicting the endpoint of the granulation process in high-speed mixer granulators of different scales from 25L to 600L. The combination of neurofuzzy logic and gene expression programing technologies allowed the modeling of the impeller power as a function of operation conditions and wet granule properties, establishing the critical variables that affect the response and obtaining a unique experimental polynomial equation (transparent model) of high predictability (R 2 > 86.78%) for all size equipment. Gene expression programing allowed the modeling of the granulation process for granulators of similar and dissimilar geometries and can be improved by implementing additional characteristics of the process, as composition variables or operation parameters (e.g., batch size, chopper speed). The principles and the methodology proposed here can be applied to understand and control manufacturing process, using any other granulation equipment, including continuous granulation processes. Copyright © 2016 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

  20. Development of automatic radiographic inspection system using digital image processing and artificial intelligence

    International Nuclear Information System (INIS)

    Itoga, Kouyu; Sugimoto, Koji; Michiba, Koji; Kato, Yuhei; Sugita, Yuji; Onda, Katsuhiro.

    1991-01-01

    The application of computers to welding inspection is expanding rapidly. The classification of the application is the collection, analysis and processing of data, the graphic display of results, the distinction of the kinds of defects and the evaluation of the harmufulness of defects and the judgement of acceptance or rejection. The application of computer techniques to the automation of data collection was realized at the relatively early stage. Data processing and the graphic display of results are the techniques in progress now, and the application of artificial intelligence to the distinction of the kinds of defects and the evaluation of harmfulness is expected to expand rapidly. In order to computerize radiographic inspection, the abilities of image processing technology and knowledge engineering must be given to computers. The object of this system is the butt joints by arc welding of the steel materials of up to 30 mm thickness. The digitizing transformation of radiographs, the distinction and evaluation of transmissivity and gradation by image processing, and only as for those, of which the picture quality satisfies the standard, the extraction of defect images, their display, the distinction of the kinds and the final judgement are carried out. The techniques of image processing, the knowledge for distinguishing the kinds of defects and the concept of the practical system are reported. (K.I.)

  1. A New Tool for Intelligent Parallel Processing of Radar/SAR Remotely Sensed Imagery

    Directory of Open Access Journals (Sweden)

    A. Castillo Atoche

    2013-01-01

    Full Text Available A novel parallel tool for large-scale image enhancement/reconstruction and postprocessing of radar/SAR sensor systems is addressed. The proposed parallel tool performs the following intelligent processing steps: image formation, for the application of different system-level effects of image degradation with a particular remote sensing (RS system and simulation of random noising effects, enhancement/reconstruction by employing nonparametric robust high-resolution techniques, and image postprocessing using the fuzzy anisotropic diffusion technique which incorporates a better edge-preserving noise removal effect and faster diffusion process. This innovative tool allows the processing of high-resolution images provided with different radar/SAR sensor systems as required by RS endusers for environmental monitoring, risk prevention, and resource management. To verify the performance implementation of the proposed parallel framework, the processing steps are developed and specifically tested on graphic processing units (GPU, achieving considerable speedups compared to the serial version of the same techniques implemented in C language.

  2. Real-time operation guide system for sintering process with artificial intelligence

    Institute of Scientific and Technical Information of China (English)

    FAN Xiao-hui; CHEN Xu-ling; JIANG Tao; LI Tao

    2005-01-01

    In order to optimize the sintering process, a real-time operation guide system with artificial intelligence was developed, mainly including the data acquisition online subsystem, the sinter chemical composition controller, the sintering process state controller, and the abnormal conditions diagnosis subsystem. Knowledge base of the sintering process controlling was constructed, and inference engine of the system was established. Sinter chemical compositions were controlled by the strategies of self-adaptive prediction, internal optimization and center on basicity. And the state of sintering was stabilized centering on permeability. In order to meet the needs of process change and make the system clear, the system has learning ability and explanation function. The software of the system was developed in Visual C++ programming language. The application of the system shows that the hitting accuracy of sinter compositions and burning through point prediction are more than 85%; the first-grade rate of sinter chemical composition, stability rate of burning through point and stability rate of sintering process are increased by 3%, 9% and 4%, respectively.

  3. Artificial Intelligence Mechanisms on Interactive Modified Simplex Method with Desirability Function for Optimising Surface Lapping Process

    Directory of Open Access Journals (Sweden)

    Pongchanun Luangpaiboon

    2014-01-01

    Full Text Available A study has been made to optimise the influential parameters of surface lapping process. Lapping time, lapping speed, downward pressure, and charging pressure were chosen from the preliminary studies as parameters to determine process performances in terms of material removal, lap width, and clamp force. The desirability functions of the-nominal-the-best were used to compromise multiple responses into the overall desirability function level or D response. The conventional modified simplex or Nelder-Mead simplex method and the interactive desirability function are performed to optimise online the parameter levels in order to maximise the D response. In order to determine the lapping process parameters effectively, this research then applies two powerful artificial intelligence optimisation mechanisms from harmony search and firefly algorithms. The recommended condition of (lapping time, lapping speed, downward pressure, and charging pressure at (33, 35, 6.0, and 5.0 has been verified by performing confirmation experiments. It showed that the D response level increased to 0.96. When compared with the current operating condition, there is a decrease of the material removal and lap width with the improved process performance indices of 2.01 and 1.14, respectively. Similarly, there is an increase of the clamp force with the improved process performance index of 1.58.

  4. An architectural framework for developing intelligent applications for the carbon dioxide capture process

    Energy Technology Data Exchange (ETDEWEB)

    Luo, C.; Zhou, Q.; Chan, C.W. [Regina Univ., SK (Canada)

    2009-07-01

    This presentation reported on the development of automated application solutions for the carbon dioxide (CO{sub 2}) capture process. An architectural framework was presented for developing intelligent systems for the process system. The chemical absorption process consists of dozens of components. It therefore generates more than a hundred different types of data. Developing automated support for these tasks is desirable because the monitoring, analysis and diagnosis of the data is very complex. The proposed framework interacts with an implemented domain ontology for the CO{sub 2} capture process, which consists of information derived from senior operators of the CO{sub 2} pilot plant at the International Test Centre for Carbon Dioxide Capture at University of Regina. The well-defined library within the framework reduces development time and cost. The framework also has built-in web-based software components for data monitoring, management, and analysis. These components provide support for generating automated solutions for the CO{sub 2} capture process. An automated monitoring system that was also developed based on the architectural framework.

  5. Political and Budgetary Oversight of the Ukrainian Intelligence Community: Processes, Problems and Prospects for Reform

    National Research Council Canada - National Science Library

    Petrov, Oleksii

    2007-01-01

    This thesis addresses the problem of providing policy and budget oversight of Ukrainian intelligence organizations in accordance with norms and practices developed in contemporary Western democracies...

  6. Process querying : enabling business intelligence through query-based process analytics

    NARCIS (Netherlands)

    Polyvyanyy, A.; Ouyang, C.; Barros, A.; van der Aalst, W.M.P.

    2017-01-01

    The volume of process-related data is growing rapidly: more and more business operations are being supported and monitored by information systems. Industry 4.0 and the corresponding industrial Internet of Things are about to generate new waves of process-related data, next to the abundance of event

  7. Prodiag--a hybrid artificial intelligence based reactor diagnostic system for process faults

    International Nuclear Information System (INIS)

    Reifman, J.; Wei, T.Y.C.; Vitela, J.E.; Applequist, C. A.; Chasensky, T.M.

    1996-01-01

    Commonwealth Research Corporation (CRC) and Argonne National Laboratory (ANL) are collaborating on a DOE-sponsored Cooperative Research and Development Agreement (CRADA), project to perform feasibility studies on a novel approach to Artificial Intelligence (Al) based diagnostics for component faults in nuclear power plants. Investigations are being performed in the construction of a first-principles physics-based plant level process diagnostic expert system (ES) and the identification of component-level fault patterns through operating component characteristics using artificial neural networks (ANNs). The purpose of the proof-of-concept project is to develop a computer-based system using this Al approach to assist process plant operators during off-normal plant conditions. The proposed computer-based system will use thermal hydraulic (T-H) signals complemented by other non-T-H signals available in the data stream to provide the process operator with the component which most likely caused the observed process disturbance.To demonstrate the scale-up feasibility of the proposed diagnostic system it is being developed for use with the Chemical Volume Control System (CVCS) of a nuclear power plant. A full-scope operator training simulator representing the Commonwealth Edison Braidwood nuclear power plant is being used both as the source of development data and as the means to evaluate the advantages of the proposed diagnostic system. This is an ongoing multi-year project and this paper presents the results to date of the CRADA phase

  8. Information Design for “Weak Signal” detection and processing in Economic Intelligence: A case study on Health resources

    Directory of Open Access Journals (Sweden)

    Sahbi Sidhom

    2011-12-01

    Full Text Available The topics of this research cover all phases of “Information Design” applied to detect and profit from weak signals in economic intelligence (EI or business intelligence (BI. The field of the information design (ID applies to the process of translating complex, unorganized or unstructured data into valuable and meaningful information. ID practice requires an interdisciplinary approach, which combines skills in graphic design (writing, analysis processing and editing, human performances technology and human factors. Applied in the context of information system, it allows end-users to easily detect implicit topics known as “weak signals” (WS. In our approach to implement the ID, the processes cover the development of a knowledge management (KM process in the context of EI. A case study concerning information monitoring health resources is presented using ID processes to outline weak signals. Both French and American bibliographic databases were applied to make the connection to multilingual concepts in the health watch process.

  9. Black-White Differences in Cognitive Processing: A Study of the Planning, Attention, Simultaneous, and Successive Theory of Intelligence

    Science.gov (United States)

    Naglieri, Jack A.; Rojahn, Johannes; Matto, Holly C.; Aquilino, Sally A.

    2005-01-01

    Researchers have typically found a mean difference of about 15 points between Blacks and Whites on traditional measures of intelligence. Some have argued that the difference between Blacks and Whites would be smaller on measures of cognitive processing. This study examined Black (n = 298) and White (n = 1,691) children on Planning, Attention,…

  10. An intelligent readout controller for Fastbus, the Fermilab FSCC

    International Nuclear Information System (INIS)

    Bowden, M.; Kwarciany, R.; Urish, J.

    1990-01-01

    This paper reports on the Fermilab FASTBUS Smart Crate Controller which is intended as a fast, versatile, and cost effective solution for the readout of FASTBUS crates. The on-board 68020 provides intelligence and a programmable microsequencer controls the main readout path. The FSCC supports communication via serial RS 232, Ethernet, and FASTBUS. The main readout path may be programmed for a variety of protocols. Currently, RS 422, VDAS, ECL line, and fiber-optic interfaces are being developed. Hardware interfacing is via the FASTBUS auxiliary connector using a personality card. Provision is made for some on-board formatting and processing of data. The 68020 may sample the data, also headers and word counts may be inserted into the data stream. Data is buffered by FIFOs to allow asynchronous readout

  11. Intelligence in Artificial Intelligence

    OpenAIRE

    Datta, Shoumen Palit Austin

    2016-01-01

    The elusive quest for intelligence in artificial intelligence prompts us to consider that instituting human-level intelligence in systems may be (still) in the realm of utopia. In about a quarter century, we have witnessed the winter of AI (1990) being transformed and transported to the zenith of tabloid fodder about AI (2015). The discussion at hand is about the elements that constitute the canonical idea of intelligence. The delivery of intelligence as a pay-per-use-service, popping out of ...

  12. Process sensors characterization based on noise analysis technique and artificial intelligence

    International Nuclear Information System (INIS)

    Mesquita, Roberto N. de; Perillo, Sergio R.P.; Santos, Roberto C. dos

    2005-01-01

    The time response of pressure and temperature sensors from the Reactor Protection System (RPS) is a requirement that must be satisfied in nuclear power plants, furthermore is an indicative of its degradation and its remaining life. The nuclear power industry and others have been eager to implement smart sensor technologies and digital instrumentation concepts to reduce manpower and effort currently spent on testing and calibration. Process parameters fluctuations during normal operation of a reactor are caused by random variations in neutron flux, heat transfer and other sources. The output sensor noise can be considered as the response of the system to an input representing the statistical nature of the underlying process which can be modeled using a time series model. Since the noise signal measurements are influenced by many factors, such as location of sensors, extraneous noise interference, and randomness in temperature and pressure fluctuation - the quantitative estimate of the time response using autoregressive noise modeling is subject to error. This technique has been used as means of sensor monitoring. In this work a set of pressure sensors installed in one experimental loop adapted from a flow calibration setup is used to test and analyze signals in a new approach using artificial intelligence techniques. A set of measurements of dynamic signals in different experimental conditions is used to distinguish and identify underlying process sources. A methodology that uses Blind Separation of Sources with a neural networks scheme is being developed to improve time response estimate reliability in noise analysis. (author)

  13. Process sensors characterization based on noise analysis technique and artificial intelligence

    Energy Technology Data Exchange (ETDEWEB)

    Mesquita, Roberto N. de; Perillo, Sergio R.P.; Santos, Roberto C. dos [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil)]. E-mail: rnavarro@ipen.br; sperillo@ipen.br; rcsantos@ipen.br

    2005-07-01

    The time response of pressure and temperature sensors from the Reactor Protection System (RPS) is a requirement that must be satisfied in nuclear power plants, furthermore is an indicative of its degradation and its remaining life. The nuclear power industry and others have been eager to implement smart sensor technologies and digital instrumentation concepts to reduce manpower and effort currently spent on testing and calibration. Process parameters fluctuations during normal operation of a reactor are caused by random variations in neutron flux, heat transfer and other sources. The output sensor noise can be considered as the response of the system to an input representing the statistical nature of the underlying process which can be modeled using a time series model. Since the noise signal measurements are influenced by many factors, such as location of sensors, extraneous noise interference, and randomness in temperature and pressure fluctuation - the quantitative estimate of the time response using autoregressive noise modeling is subject to error. This technique has been used as means of sensor monitoring. In this work a set of pressure sensors installed in one experimental loop adapted from a flow calibration setup is used to test and analyze signals in a new approach using artificial intelligence techniques. A set of measurements of dynamic signals in different experimental conditions is used to distinguish and identify underlying process sources. A methodology that uses Blind Separation of Sources with a neural networks scheme is being developed to improve time response estimate reliability in noise analysis. (author)

  14. Expert system in OPS5 for intelligent processing of the alarms in nuclear plants

    International Nuclear Information System (INIS)

    Cavalcante Junior, Jose Airton Chaves

    1997-11-01

    This work intends to establish a model of knowledge representation based on a expert system to supervise either security or operating to be applied generally on monitoring and detecting faults of industrial processes. The model structure proposed here let the system represent the knowledge related to faults on a process using a combination of rules either basic or associative. Besides, the model proposed has a mechanism of propagation of events in real time that acts on this structure making it possible to have an intelligent alarm processing. The rules used by the system define faults from the data acquired by instrumentation (basic rules), or from the establishment of a conjunction of faults already existent (associate rules). The computing implementation of the model defined in this work was developed in OPS5. It was applied on an example consisting of the shutdown of the Angra-I's power plant and was called FDAX (FDA Extended). For the simulated tests the FDAX was connected to the SICA (Integrated System of Angra-I Computers). It results save validity to the model, confirming thus its performance to real time applications. (author)

  15. Gender Differences in the Relationship between Emotional Intelligence and Right Hemisphere Lateralization for Facial Processing

    Science.gov (United States)

    Castro-Schilo, Laura; Kee, Daniel W.

    2010-01-01

    The present study examined relationships between emotional intelligence, measured by the Mayer-Salovey-Caruso Emotional Intelligence Test, and right hemisphere dominance for a free vision chimeric face test. A sample of 122 ethnically diverse college students participated and completed online versions of the forenamed tests. A hierarchical…

  16. The Impact of Business Intelligence (BI Competence on Customer Relationship Management (CRM Process: An Empirical Investigation of the Banking Industry

    Directory of Open Access Journals (Sweden)

    Ali Mortezaei

    2018-03-01

    Full Text Available Nowadays, establishing long-term and effective relationships with customers is a key factor in understanding customers’ needs and preferences and achieving competitive advantage. In addition, companies are facing with a growing need for information and analytical knowledge about their customers, market, competitors, organizational environment, and other factors affecting their business. Business intelligence has been considered as a response to this need. The purpose of this study is to investigate the role of business intelligence competence in improving customer relationship management process. Based on the literature review and the competence – capability relationship paradigm, a conceptual model was developed comprising of different dimensions of business intelligence competence and customer relationship management processes. The data were collected from the banking sector and partial least squares structural equation modelling was employed for data analysis. Empirical results showed that organizational business intelligence competence, comprising of managerial, technical, and cultural competence, has a significantly positive impact on enhancing capabilities of customer relationship management process including initiation, maintenance, and termination of the relationship.

  17. A new on-board imaging treatment technique for palliative and emergency treatments in radiation oncology

    International Nuclear Information System (INIS)

    Held, Mareike

    2016-01-01

    This dissertation focuses on the use of on-board imaging systems as the basis for treatment planning, presenting an additional application for on-board images. A clinical workflow is developed to simulate, plan, and deliver a simple radiation oncology treatment rapidly, using 3D patient scans. The work focuses on an on-line dose planning and delivery process based on on-board images entirely performed with the patient set up on the treatment couch of the linear accelerator. This potentially reduces the time between patient simulation and treatment to about 30 minutes. The basis for correct dose calculation is the accurate image gray scale to tissue density calibration. The gray scale, which is defined in CT Numbers, is dependent on the energy spectrum of the beam. Therefore, an understanding of the physics characteristics of each on-board system is required to evaluate the impact on image quality, especially regarding the underlying cause of image noise, contrast, and non-uniformity. Modern on-board imaging systems, including kV and megavoltage (MV) cone beam (CB) CT as well as MV CT, are characterized in terms of image quality and stability. A library of phantom and patient CT images is used to evaluate the dose calculation accuracy for the on-board images. The dose calculation objective is to stay within 5% local dose differences compared to standard kV CT dose planning. The objective is met in many treatment cases. However, dose calculation accuracy depends on the anatomical treatment site. While on-board CT-based treatments of the head and extremities are predictable within 5% on all systems, lung tissue and air cavities may create local dose discrepancies of more than 5%. The image quality varies between the tested units. Consequently, the CT number-to-density calibration is defined independently for each system. In case of some imaging systems, the CT numbers of the images are dependent on the protocol used for on-board imaging, which defines the imaging dose

  18. A new on-board imaging treatment technique for palliative and emergency treatments in radiation oncology

    Energy Technology Data Exchange (ETDEWEB)

    Held, Mareike

    2016-03-23

    This dissertation focuses on the use of on-board imaging systems as the basis for treatment planning, presenting an additional application for on-board images. A clinical workflow is developed to simulate, plan, and deliver a simple radiation oncology treatment rapidly, using 3D patient scans. The work focuses on an on-line dose planning and delivery process based on on-board images entirely performed with the patient set up on the treatment couch of the linear accelerator. This potentially reduces the time between patient simulation and treatment to about 30 minutes. The basis for correct dose calculation is the accurate image gray scale to tissue density calibration. The gray scale, which is defined in CT Numbers, is dependent on the energy spectrum of the beam. Therefore, an understanding of the physics characteristics of each on-board system is required to evaluate the impact on image quality, especially regarding the underlying cause of image noise, contrast, and non-uniformity. Modern on-board imaging systems, including kV and megavoltage (MV) cone beam (CB) CT as well as MV CT, are characterized in terms of image quality and stability. A library of phantom and patient CT images is used to evaluate the dose calculation accuracy for the on-board images. The dose calculation objective is to stay within 5% local dose differences compared to standard kV CT dose planning. The objective is met in many treatment cases. However, dose calculation accuracy depends on the anatomical treatment site. While on-board CT-based treatments of the head and extremities are predictable within 5% on all systems, lung tissue and air cavities may create local dose discrepancies of more than 5%. The image quality varies between the tested units. Consequently, the CT number-to-density calibration is defined independently for each system. In case of some imaging systems, the CT numbers of the images are dependent on the protocol used for on-board imaging, which defines the imaging dose

  19. On-Board, Real-Time Preprocessing System for Optical Remote-Sensing Imagery.

    Science.gov (United States)

    Qi, Baogui; Shi, Hao; Zhuang, Yin; Chen, He; Chen, Liang

    2018-04-25

    With the development of remote-sensing technology, optical remote-sensing imagery processing has played an important role in many application fields, such as geological exploration and natural disaster prevention. However, relative radiation correction and geometric correction are key steps in preprocessing because raw image data without preprocessing will cause poor performance during application. Traditionally, remote-sensing data are downlinked to the ground station, preprocessed, and distributed to users. This process generates long delays, which is a major bottleneck in real-time applications for remote-sensing data. Therefore, on-board, real-time image preprocessing is greatly desired. In this paper, a real-time processing architecture for on-board imagery preprocessing is proposed. First, a hierarchical optimization and mapping method is proposed to realize the preprocessing algorithm in a hardware structure, which can effectively reduce the computation burden of on-board processing. Second, a co-processing system using a field-programmable gate array (FPGA) and a digital signal processor (DSP; altogether, FPGA-DSP) based on optimization is designed to realize real-time preprocessing. The experimental results demonstrate the potential application of our system to an on-board processor, for which resources and power consumption are limited.

  20. On-Board, Real-Time Preprocessing System for Optical Remote-Sensing Imagery

    Science.gov (United States)

    Qi, Baogui; Zhuang, Yin; Chen, He; Chen, Liang

    2018-01-01

    With the development of remote-sensing technology, optical remote-sensing imagery processing has played an important role in many application fields, such as geological exploration and natural disaster prevention. However, relative radiation correction and geometric correction are key steps in preprocessing because raw image data without preprocessing will cause poor performance during application. Traditionally, remote-sensing data are downlinked to the ground station, preprocessed, and distributed to users. This process generates long delays, which is a major bottleneck in real-time applications for remote-sensing data. Therefore, on-board, real-time image preprocessing is greatly desired. In this paper, a real-time processing architecture for on-board imagery preprocessing is proposed. First, a hierarchical optimization and mapping method is proposed to realize the preprocessing algorithm in a hardware structure, which can effectively reduce the computation burden of on-board processing. Second, a co-processing system using a field-programmable gate array (FPGA) and a digital signal processor (DSP; altogether, FPGA-DSP) based on optimization is designed to realize real-time preprocessing. The experimental results demonstrate the potential application of our system to an on-board processor, for which resources and power consumption are limited. PMID:29693585

  1. Intelligent Mission Controller Node

    National Research Council Canada - National Science Library

    Perme, David

    2002-01-01

    The goal of the Intelligent Mission Controller Node (IMCN) project was to improve the process of translating mission taskings between real-world Command, Control, Communications, Computers, and Intelligence (C41...

  2. An intelligent system for monitoring and diagnosis of the CO{sub 2} capture process

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Q.; Chan, C.W.; Tontiwachwuthikul, P. [University of Regina, Regina, SK (Canada). Faculty of Engineering

    2011-07-15

    Amine-based carbon dioxide capture has been widely considered as a feasible ideal technology for reducing large-scale CO{sub 2} emissions and mitigating global warming. The operation of amine-based CO{sub 2} capture is a complicated task, which involves monitoring over 100 process parameters and careful manipulation of numerous valves and pumps. The current research in the field of CO{sub 2} capture has emphasized the need for improving CO{sub 2} capture efficiency and enhancing plant performance. In the present study, artificial intelligence techniques were applied for developing a knowledge-based expert system that aims at effectively monitoring and controlling the CO{sub 2} capture process and thereby enhancing CO{sub 2} capture efficiency. In developing the system, the inferential modeling technique (IMT) was applied to analyze the domain knowledge and problem-solving techniques, and a knowledge base was developed on DeltaV Simulate. The expert system helps to enhance CO{sub 2} capture system performance and efficiency by reducing the time required for diagnosis and problem solving if abnormal conditions occur. The expert system can be used as a decision-support tool that helps inexperienced operators control the plant: it can be used also for training novice operators.

  3. Intelligent Technique for Signal Processing to Identify the Brain Disorder for Epilepsy Captures Using Fuzzy Systems

    Directory of Open Access Journals (Sweden)

    Gurumurthy Sasikumar

    2016-01-01

    Full Text Available The new direction of understand the signal that is created from the brain organization is one of the main chores in the brain signal processing. Amid all the neurological disorders the human brain epilepsy is measured as one of the extreme prevalent and then programmed artificial intelligence detection technique is an essential due to the crooked and unpredictable nature of happening of epileptic seizures. We proposed an Improved Fuzzy firefly algorithm, which would enhance the classification of the brain signal efficiently with minimum iteration. An important bunching technique created on fuzzy logic is the Fuzzy C means. Together in the feature domain with the spatial domain the features gained after multichannel EEG signals remained combined by means of fuzzy algorithms. And for better precision segmentation process the firefly algorithm is applied to optimize the Fuzzy C-means membership function. Simultaneously for the efficient clustering method the convergence criteria are set. On the whole the proposed technique yields more accurate results and that gives an edge over other techniques. This proposed algorithm result compared with other algorithms like fuzzy c means algorithm and PSO algorithm.

  4. An intelligent signal processing and pattern recognition technique for defect identification using an active sensor network

    Science.gov (United States)

    Su, Zhongqing; Ye, Lin

    2004-08-01

    The practical utilization of elastic waves, e.g. Rayleigh-Lamb waves, in high-performance structural health monitoring techniques is somewhat impeded due to the complicated wave dispersion phenomena, the existence of multiple wave modes, the high susceptibility to diverse interferences, the bulky sampled data and the difficulty in signal interpretation. An intelligent signal processing and pattern recognition (ISPPR) approach using the wavelet transform and artificial neural network algorithms was developed; this was actualized in a signal processing package (SPP). The ISPPR technique comprehensively functions as signal filtration, data compression, characteristic extraction, information mapping and pattern recognition, capable of extracting essential yet concise features from acquired raw wave signals and further assisting in structural health evaluation. For validation, the SPP was applied to the prediction of crack growth in an alloy structural beam and construction of a damage parameter database for defect identification in CF/EP composite structures. It was clearly apparent that the elastic wave propagation-based damage assessment could be dramatically streamlined by introduction of the ISPPR technique.

  5. Middle manager role and contribution towards the competitive intelligence process: A case of Irish subsidiaries

    Directory of Open Access Journals (Sweden)

    Willie Chinyamurindi

    2016-07-01

    Full Text Available Background: Calls have been made especially during a period of global competition and economic austerity for research that focuses on how competitive intelligence (CI is actually generated within organisations. Objectives: The aim of this study was to understand the views and experiences of middle managers with regard to their role and contribution towards the CI process within Irish subsidiaries of the Multinational Corporation (MNC. Method: The study adopts a qualitative approach using the semi-structured interview technique to generate narratives and themes around how CI is generated using a sample of 15 middle managers drawn from five participating Irish subsidiaries. Results: Based on the analysis of the narratives of the middle managers, three main themes emerged as findings. Firstly, the process of gathering CI was facilitated by the reliance on internal and external tools. Secondly, information gathered from the use of such tools was then communicated by middle managers to top managers to inform the making of strategic decisions. Thus, (and thirdly, middle managers were found to occupy an important role not only through the execution of their management duties but by extending this influence towards the generation of information deemed to affect the competitive position of not just the subsidiary but also the parent company. Conclusion: The study concludes by focusing on the implications and recommendations based on the three themes drawn from the empirical data.

  6. Spacecube: A Family of Reconfigurable Hybrid On-Board Science Data Processors

    Science.gov (United States)

    Flatley, Thomas P.

    2015-01-01

    SpaceCube is a family of Field Programmable Gate Array (FPGA) based on-board science data processing systems developed at the NASA Goddard Space Flight Center (GSFC). The goal of the SpaceCube program is to provide 10x to 100x improvements in on-board computing power while lowering relative power consumption and cost. SpaceCube is based on the Xilinx Virtex family of FPGAs, which include processor, FPGA logic and digital signal processing (DSP) resources. These processing elements are leveraged to produce a hybrid science data processing platform that accelerates the execution of algorithms by distributing computational functions to the most suitable elements. This approach enables the implementation of complex on-board functions that were previously limited to ground based systems, such as on-board product generation, data reduction, calibration, classification, eventfeature detection, data mining and real-time autonomous operations. The system is fully reconfigurable in flight, including data parameters, software and FPGA logic, through either ground commanding or autonomously in response to detected eventsfeatures in the instrument data stream.

  7. On-Board File Management and Its Application in Flight Operations

    Science.gov (United States)

    Kuo, N.

    1998-01-01

    In this paper, the author presents the minimum functions required for an on-board file management system. We explore file manipulation processes and demonstrate how the file transfer along with the file management system will be utilized to support flight operations and data delivery.

  8. Artificial Intelligence Based Selection of Optimal Cutting Tool and Process Parameters for Effective Turning and Milling Operations

    Science.gov (United States)

    Saranya, Kunaparaju; John Rozario Jegaraj, J.; Ramesh Kumar, Katta; Venkateshwara Rao, Ghanta

    2016-06-01

    With the increased trend in automation of modern manufacturing industry, the human intervention in routine, repetitive and data specific activities of manufacturing is greatly reduced. In this paper, an attempt has been made to reduce the human intervention in selection of optimal cutting tool and process parameters for metal cutting applications, using Artificial Intelligence techniques. Generally, the selection of appropriate cutting tool and parameters in metal cutting is carried out by experienced technician/cutting tool expert based on his knowledge base or extensive search from huge cutting tool database. The present proposed approach replaces the existing practice of physical search for tools from the databooks/tool catalogues with intelligent knowledge-based selection system. This system employs artificial intelligence based techniques such as artificial neural networks, fuzzy logic and genetic algorithm for decision making and optimization. This intelligence based optimal tool selection strategy is developed using Mathworks Matlab Version 7.11.0 and implemented. The cutting tool database was obtained from the tool catalogues of different tool manufacturers. This paper discusses in detail, the methodology and strategies employed for selection of appropriate cutting tool and optimization of process parameters based on multi-objective optimization criteria considering material removal rate, tool life and tool cost.

  9. Visual function and cognitive speed of processing mediate age-related decline in memory span and fluid intelligence.

    Science.gov (United States)

    Clay, Olivio J; Edwards, Jerri D; Ross, Lesley A; Okonkwo, Ozioma; Wadley, Virginia G; Roth, David L; Ball, Karlene K

    2009-06-01

    To evaluate the relationship between sensory and cognitive decline, particularly with respect to speed of processing, memory span, and fluid intelligence. In addition, the common cause, sensory degradation and speed of processing hypotheses were compared. Structural equation modeling was used to investigate the complex relationships among age-related decrements in these areas. Cross-sectional data analyses included 842 older adult participants (M = 73 years). After accounting for age-related declines in vision and processing speed, the direct associations between age and memory span and between age and fluid intelligence were nonsignificant. Older age was associated with visual decline, which was associated with slower speed of processing, which in turn was associated with greater cognitive deficits. The findings support both the sensory degradation and speed of processing accounts of age-related, cognitive decline. Furthermore, the findings highlight positive aspects of normal cognitive aging in that older age may not be associated with a loss of fluid intelligence if visual sensory functioning and processing speed can be maintained.

  10. Planning pesticides usage for herbal and animal pests based on intelligent classification system with image processing and neural networks

    Directory of Open Access Journals (Sweden)

    Dimililer Kamil

    2018-01-01

    Full Text Available Pests are divided into two as herbal and animal pests in agriculture, and detection and use of minimum pesticides are quite challenging task. Last three decades, researchers have been improving their studies on these manners. Therefore, effective, efficient, and as well as intelligent systems are designed and modelled. In this paper, an intelligent classification system is designed for detecting pests as herbal or animal to use of proper pesticides accordingly. The designed system suggests two main stages. Firstly, images are processed using different image processing techniques that images have specific distinguishing geometric patterns. The second stage is neural network phase for classification. A backpropagation neural network is used for training and testing with processed images. System is tested, and experiment results show efficiency and effective classification rate. Autonomy and time efficiency within the pesticide usage are also discussed.

  11. TECHNICAL MAINTENANCE EFFICIENCY OF THE AIRCRAFT MAINTENANCE-FREE ON-BOARD SYSTEM BETWEEN SCHEDULED MAINTENANCES

    Directory of Open Access Journals (Sweden)

    A. M. Bronnikov

    2017-01-01

    Full Text Available The avionics concept of the maintenance-free on-board equipment implies the absence of necessity to maintain onboard systems between scheduled maintenance, preserving the required operational and technical characteristics; it should be achieved by automatic diagnosis of the technical condition and the application of active means of ensuring a failsafe design, allowing to change the structure of the system to maintain its functions in case of failure. It is supposed that such equipment will reduce substantially and in the limit eliminate traditional maintenance of aircraft between scheduled maintenance, ensuring maximum readiness for use, along with improving safety. The paper proposes a methodology for evaluating the efficiency of maintenance-free between scheduled maintenance aircraft system with homogeneous redundancy. The excessive redundant elements allow the system to accumulate failures which are repaired during the routine maintenance. If the number of failures of any reserve is approaching a critical value, the recovery of the on-board system (elimination of all failures is carried out between scheduled maintenance by conducting rescue and recovery operations. It is believed that service work leads to the elimination of all failures and completely updates the on-board system. The process of system operational status changes is described with the discrete-continuous model in the flight time. The average losses in the sorties and the average cost of operation are used as integrated efficiency indicators of system operation. For example, the evaluation of the operation efficiency of formalized on-board system with homogeneous redundancy demonstrates the efficiency of the proposed methodology and the possibility of its use while analyzing the efficiency of the maintenance-free operation equipment between scheduled periods. As well as a comparative analysis of maintenance-free operation efficiency of the on-board system with excessive

  12. 2015 Chinese Intelligent Systems Conference

    CERN Document Server

    Du, Junping; Li, Hongbo; Zhang, Weicun; CISC’15

    2016-01-01

    This book presents selected research papers from the 2015 Chinese Intelligent Systems Conference (CISC’15), held in Yangzhou, China. The topics covered include multi-agent systems, evolutionary computation, artificial intelligence, complex systems, computation intelligence and soft computing, intelligent control, advanced control technology, robotics and applications, intelligent information processing, iterative learning control, and machine learning. Engineers and researchers from academia, industry and the government can gain valuable insights into solutions combining ideas from multiple disciplines in the field of intelligent systems.

  13. Artificial intelligence framework for simulating clinical decision-making: a Markov decision process approach.

    Science.gov (United States)

    Bennett, Casey C; Hauser, Kris

    2013-01-01

    In the modern healthcare system, rapidly expanding costs/complexity, the growing myriad of treatment options, and exploding information streams that often do not effectively reach the front lines hinder the ability to choose optimal treatment decisions over time. The goal in this paper is to develop a general purpose (non-disease-specific) computational/artificial intelligence (AI) framework to address these challenges. This framework serves two potential functions: (1) a simulation environment for exploring various healthcare policies, payment methodologies, etc., and (2) the basis for clinical artificial intelligence - an AI that can "think like a doctor". This approach combines Markov decision processes and dynamic decision networks to learn from clinical data and develop complex plans via simulation of alternative sequential decision paths while capturing the sometimes conflicting, sometimes synergistic interactions of various components in the healthcare system. It can operate in partially observable environments (in the case of missing observations or data) by maintaining belief states about patient health status and functions as an online agent that plans and re-plans as actions are performed and new observations are obtained. This framework was evaluated using real patient data from an electronic health record. The results demonstrate the feasibility of this approach; such an AI framework easily outperforms the current treatment-as-usual (TAU) case-rate/fee-for-service models of healthcare. The cost per unit of outcome change (CPUC) was $189 vs. $497 for AI vs. TAU (where lower is considered optimal) - while at the same time the AI approach could obtain a 30-35% increase in patient outcomes. Tweaking certain AI model parameters could further enhance this advantage, obtaining approximately 50% more improvement (outcome change) for roughly half the costs. Given careful design and problem formulation, an AI simulation framework can approximate optimal

  14. Modeling of steam distillation mechanism during steam injection process using artificial intelligence.

    Science.gov (United States)

    Daryasafar, Amin; Ahadi, Arash; Kharrat, Riyaz

    2014-01-01

    Steam distillation as one of the important mechanisms has a great role in oil recovery in thermal methods and so it is important to simulate this process experimentally and theoretically. In this work, the simulation of steam distillation is performed on sixteen sets of crude oil data found in the literature. Artificial intelligence (AI) tools such as artificial neural network (ANN) and also adaptive neurofuzzy interference system (ANFIS) are used in this study as effective methods to simulate the distillate recoveries of these sets of data. Thirteen sets of data were used to train the models and three sets were used to test the models. The developed models are highly compatible with respect to input oil properties and can predict the distillate yield with minimum entry. For showing the performance of the proposed models, simulation of steam distillation is also done using modified Peng-Robinson equation of state. Comparison between the calculated distillates by ANFIS and neural network models and also equation of state-based method indicates that the errors of the ANFIS model for training data and test data sets are lower than those of other methods.

  15. Digital image analysis in breast pathology-from image processing techniques to artificial intelligence.

    Science.gov (United States)

    Robertson, Stephanie; Azizpour, Hossein; Smith, Kevin; Hartman, Johan

    2018-04-01

    Breast cancer is the most common malignant disease in women worldwide. In recent decades, earlier diagnosis and better adjuvant therapy have substantially improved patient outcome. Diagnosis by histopathology has proven to be instrumental to guide breast cancer treatment, but new challenges have emerged as our increasing understanding of cancer over the years has revealed its complex nature. As patient demand for personalized breast cancer therapy grows, we face an urgent need for more precise biomarker assessment and more accurate histopathologic breast cancer diagnosis to make better therapy decisions. The digitization of pathology data has opened the door to faster, more reproducible, and more precise diagnoses through computerized image analysis. Software to assist diagnostic breast pathology through image processing techniques have been around for years. But recent breakthroughs in artificial intelligence (AI) promise to fundamentally change the way we detect and treat breast cancer in the near future. Machine learning, a subfield of AI that applies statistical methods to learn from data, has seen an explosion of interest in recent years because of its ability to recognize patterns in data with less need for human instruction. One technique in particular, known as deep learning, has produced groundbreaking results in many important problems including image classification and speech recognition. In this review, we will cover the use of AI and deep learning in diagnostic breast pathology, and other recent developments in digital image analysis. Copyright © 2017 Elsevier Inc. All rights reserved.

  16. Modeling of Steam Distillation Mechanism during Steam Injection Process Using Artificial Intelligence

    Science.gov (United States)

    Ahadi, Arash; Kharrat, Riyaz

    2014-01-01

    Steam distillation as one of the important mechanisms has a great role in oil recovery in thermal methods and so it is important to simulate this process experimentally and theoretically. In this work, the simulation of steam distillation is performed on sixteen sets of crude oil data found in the literature. Artificial intelligence (AI) tools such as artificial neural network (ANN) and also adaptive neurofuzzy interference system (ANFIS) are used in this study as effective methods to simulate the distillate recoveries of these sets of data. Thirteen sets of data were used to train the models and three sets were used to test the models. The developed models are highly compatible with respect to input oil properties and can predict the distillate yield with minimum entry. For showing the performance of the proposed models, simulation of steam distillation is also done using modified Peng-Robinson equation of state. Comparison between the calculated distillates by ANFIS and neural network models and also equation of state-based method indicates that the errors of the ANFIS model for training data and test data sets are lower than those of other methods. PMID:24883365

  17. Prediction of Surface Roughness in End Milling Process Using Intelligent Systems: A Comparative Study

    Directory of Open Access Journals (Sweden)

    Abdel Badie Sharkawy

    2011-01-01

    Full Text Available A study is presented to model surface roughness in end milling process. Three types of intelligent networks have been considered. They are (i radial basis function neural networks (RBFNs, (ii adaptive neurofuzzy inference systems (ANFISs, and (iii genetically evolved fuzzy inference systems (G-FISs. The machining parameters, namely, the spindle speed, feed rate, and depth of cut have been used as inputs to model the workpiece surface roughness. The goal is to get the best prediction accuracy. The procedure is illustrated using experimental data of end milling 6061 aluminum alloy. The three networks have been trained using experimental training data. After training, they have been examined using another set of data, that is, validation data. Results are compared with previously published results. It is concluded that ANFIS networks may suffer the local minima problem, and genetic tuning of fuzzy networks cannot insure perfect optimality unless suitable parameter setting (population size, number of generations etc. and tuning range for the FIS, parameters are used which can be hardly satisfied. It is shown that the RBFN model has the best performance (prediction accuracy in this particular case.

  18. Advanced On Board Inert Gas Generation System (OBBIGS), Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — Valcor Engineering Corporation proposes to develop an advanced On Board Inert Gas Generation System, OBIGGS, for aircraft fuel tank inerting to prevent hazardous...

  19. Intelligent Vehicle Health Management

    Science.gov (United States)

    Paris, Deidre E.; Trevino, Luis; Watson, Michael D.

    2005-01-01

    As a part of the overall goal of developing Integrated Vehicle Health Management systems for aerospace vehicles, the NASA Faculty Fellowship Program (NFFP) at Marshall Space Flight Center has performed a pilot study on IVHM principals which integrates researched IVHM technologies in support of Integrated Intelligent Vehicle Management (IIVM). IVHM is the process of assessing, preserving, and restoring system functionality across flight and ground systems (NASA NGLT 2004). The framework presented in this paper integrates advanced computational techniques with sensor and communication technologies for spacecraft that can generate responses through detection, diagnosis, reasoning, and adapt to system faults in support of INM. These real-time responses allow the IIVM to modify the affected vehicle subsystem(s) prior to a catastrophic event. Furthermore, the objective of this pilot program is to develop and integrate technologies which can provide a continuous, intelligent, and adaptive health state of a vehicle and use this information to improve safety and reduce costs of operations. Recent investments in avionics, health management, and controls have been directed towards IIVM. As this concept has matured, it has become clear the INM requires the same sensors and processing capabilities as the real-time avionics functions to support diagnosis of subsystem problems. New sensors have been proposed, in addition, to augment the avionics sensors to support better system monitoring and diagnostics. As the designs have been considered, a synergy has been realized where the real-time avionics can utilize sensors proposed for diagnostics and prognostics to make better real-time decisions in response to detected failures. IIVM provides for a single system allowing modularity of functions and hardware across the vehicle. The framework that supports IIVM consists of 11 major on-board functions necessary to fully manage a space vehicle maintaining crew safety and mission

  20. Driver's various information process and multi-ruled decision-making mechanism: a fundamental of intelligent driving shaping model

    Directory of Open Access Journals (Sweden)

    Wuhong Wang

    2011-05-01

    Full Text Available The most difficult but important problem in advance driver assistance system development is how to measure and model the behavioral response of drivers with focusing on the cognition process. This paper describes driver's deceleration and acceleration behavior based on driving situation awareness in the car-following process, and then presents several driving models for analysis of driver's safety approaching behavior in traffic operation. The emphasis of our work is placed on the research of driver's various information process and multi-ruled decisionmaking mechanism by considering the complicated control process of driving; the results will be able to provide a theoretical basis for intelligent driving shaping model.

  1. Artificial intelligence versus statistical modeling and optimization of continuous bead milling process for bacterial cell lysis

    Directory of Open Access Journals (Sweden)

    Shafiul Haque

    2016-11-01

    Full Text Available AbstractFor a commercially viable recombinant intracellular protein production process, efficient cell lysis and protein release is a major bottleneck. The recovery of recombinant protein, cholesterol oxidase (COD was studied in a continuous bead milling process. A full factorial Response Surface Model (RSM design was employed and compared to Artificial Neural Networks coupled with Genetic Algorithm (ANN-GA. Significant process variables, cell slurry feed rate (A, bead load (B, cell load (C and run time (D, were investigated and optimized for maximizing COD recovery. RSM predicted an optimum of feed rate of 310.73 mL/h, bead loading of 79.9% (v/v, cell loading OD600 nm of 74, and run time of 29.9 min with a recovery of ~3.2 g/L. ANN coupled with GA predicted a maximum COD recovery of ~3.5 g/L at an optimum feed rate (mL/h: 258.08, bead loading (%, v/v: 80%, cell loading (OD600 nm: 73.99, and run time of 32 min. An overall 3.7-fold increase in productivity is obtained when compared to a batch process. Optimization and comparison of statistical vs. artificial intelligence techniques in continuous bead milling process has been attempted for the very first time in our study. We were able to successfully represent the complex non-linear multivariable dependence of enzyme recovery on bead milling parameters. The quadratic second order response functions are not flexible enough to represent such complex non-linear dependence. ANN being a summation function of multiple layers are capable to represent complex non-linear dependence of variables in this case; enzyme recovery as a function of bead milling parameters. Since GA can even optimize discontinuous functions present study cites a perfect example of using machine learning (ANN in combination with evolutionary optimization (GA for representing undefined biological functions which is the case for common industrial processes involving biological moieties.

  2. Artificial intelligence for the modeling and control of combustion processes: a review

    Energy Technology Data Exchange (ETDEWEB)

    Kalogirou, S.A. [Higher Technical Inst., Nicosia, Cyprus (Greece). Dept. of Mechanical Engineering

    2003-07-01

    Artificial intelligence (AI) systems are widely accepted as a technology offering an alternative way to tackle complex and ill-defined problems. They can learn from examples, are fault tolerant in the sense that they are able to handle noisy and incomplete data, are able to deal with non-linear problems, and once trained can perform prediction and generalization at high speed. They have been used in diverse applications in control, robotics, pattern recognition, forecasting, medicine, power systems, manufacturing, optimization, signal processing, and social/psychological sciences. They are particularly useful in system modeling such as in implementing complex mappings and system identification. Al systems comprise areas like, expert systems, artificial neural networks, genetic algorithms, fuzzy logic and various hybrid systems, which combine two or more techniques. The major objective of this paper is to illustrate how Al techniques might play an important role in modeling and prediction of the performance and control of combustion process. The paper outlines an understanding of how AI systems operate by way of presenting a number of problems in the different disciplines of combustion engineering. The various applications of AI are presented in a thematic rather than a chronological or any other order. Problems presented include two main areas: combustion systems and internal combustion (IC) engines. Combustion systems include boilers, furnaces and incinerators modeling and emissions prediction, whereas, IC engines include diesel and spark ignition engines and gas engines modeling and control. Results presented in this paper, are testimony to the potential of Al as a design tool in many areas of combustion engineering. (author)

  3. Artificial intelligence for the modeling and control of combustion processes: a review

    Energy Technology Data Exchange (ETDEWEB)

    Soteris A. Kalogirou, [Higher Technical Institute, Nicosia (Cyprus). Department of Mechanical Engineering

    2003-07-01

    Artificial intelligence (AI) systems are widely accepted as a technology offering an alternative way to tackle complex and ill-defined problems. They can learn from examples, are fault tolerant in the sense that they are able to handle noisy and incomplete data, are able to deal with non-linear problems, and once trained can perform prediction and generalization at high speed. They have been used in diverse applications in control, robotics, pattern recognition, forecasting, medicine, power systems, manufacturing, optimization, signal processing, and social/psychological sciences. They are particularly useful in system modeling such as in implementing complex mappings and system identification. AI systems comprise areas like, expert systems, artificial neural networks, genetic algorithms, fuzzy logic and various hybrid systems, which combine two or more techniques. The major objective of this paper is to illustrate how AI techniques might play an important role in modeling and prediction of the performance and control of combustion process. The paper outlines an understanding of how AI systems operate by way of presenting a number of problems in the different disciplines of combustion engineering. The various applications of AI are presented in a thematic rather than a chronological or any other order. Problems presented include two main areas: combustion systems and internal combustion (IC) engines. Combustion systems include boilers, furnaces and incinerators modeling and emissions prediction, whereas, IC engines include diesel and spark ignition engines and gas engines modeling and control. Results presented in this paper, are testimony to the potential of AI as a design tool in many areas of combustion engineering. 109 refs., 31 figs., 11 tabs.

  4. Computer aided diagnosis based on medical image processing and artificial intelligence methods

    Science.gov (United States)

    Stoitsis, John; Valavanis, Ioannis; Mougiakakou, Stavroula G.; Golemati, Spyretta; Nikita, Alexandra; Nikita, Konstantina S.

    2006-12-01

    Advances in imaging technology and computer science have greatly enhanced interpretation of medical images, and contributed to early diagnosis. The typical architecture of a Computer Aided Diagnosis (CAD) system includes image pre-processing, definition of region(s) of interest, features extraction and selection, and classification. In this paper, the principles of CAD systems design and development are demonstrated by means of two examples. The first one focuses on the differentiation between symptomatic and asymptomatic carotid atheromatous plaques. For each plaque, a vector of texture and motion features was estimated, which was then reduced to the most robust ones by means of ANalysis of VAriance (ANOVA). Using fuzzy c-means, the features were then clustered into two classes. Clustering performances of 74%, 79%, and 84% were achieved for texture only, motion only, and combinations of texture and motion features, respectively. The second CAD system presented in this paper supports the diagnosis of focal liver lesions and is able to characterize liver tissue from Computed Tomography (CT) images as normal, hepatic cyst, hemangioma, and hepatocellular carcinoma. Five texture feature sets were extracted for each lesion, while a genetic algorithm based feature selection method was applied to identify the most robust features. The selected feature set was fed into an ensemble of neural network classifiers. The achieved classification performance was 100%, 93.75% and 90.63% in the training, validation and testing set, respectively. It is concluded that computerized analysis of medical images in combination with artificial intelligence can be used in clinical practice and may contribute to more efficient diagnosis.

  5. Computer aided diagnosis based on medical image processing and artificial intelligence methods

    International Nuclear Information System (INIS)

    Stoitsis, John; Valavanis, Ioannis; Mougiakakou, Stavroula G.; Golemati, Spyretta; Nikita, Alexandra; Nikita, Konstantina S.

    2006-01-01

    Advances in imaging technology and computer science have greatly enhanced interpretation of medical images, and contributed to early diagnosis. The typical architecture of a Computer Aided Diagnosis (CAD) system includes image pre-processing, definition of region(s) of interest, features extraction and selection, and classification. In this paper, the principles of CAD systems design and development are demonstrated by means of two examples. The first one focuses on the differentiation between symptomatic and asymptomatic carotid atheromatous plaques. For each plaque, a vector of texture and motion features was estimated, which was then reduced to the most robust ones by means of ANalysis of VAriance (ANOVA). Using fuzzy c-means, the features were then clustered into two classes. Clustering performances of 74%, 79%, and 84% were achieved for texture only, motion only, and combinations of texture and motion features, respectively. The second CAD system presented in this paper supports the diagnosis of focal liver lesions and is able to characterize liver tissue from Computed Tomography (CT) images as normal, hepatic cyst, hemangioma, and hepatocellular carcinoma. Five texture feature sets were extracted for each lesion, while a genetic algorithm based feature selection method was applied to identify the most robust features. The selected feature set was fed into an ensemble of neural network classifiers. The achieved classification performance was 100%, 93.75% and 90.63% in the training, validation and testing set, respectively. It is concluded that computerized analysis of medical images in combination with artificial intelligence can be used in clinical practice and may contribute to more efficient diagnosis

  6. Computer aided diagnosis based on medical image processing and artificial intelligence methods

    Energy Technology Data Exchange (ETDEWEB)

    Stoitsis, John [National Technical University of Athens, School of Electrical and Computer Engineering, Athens 157 71 (Greece)]. E-mail: stoitsis@biosim.ntua.gr; Valavanis, Ioannis [National Technical University of Athens, School of Electrical and Computer Engineering, Athens 157 71 (Greece); Mougiakakou, Stavroula G. [National Technical University of Athens, School of Electrical and Computer Engineering, Athens 157 71 (Greece); Golemati, Spyretta [National Technical University of Athens, School of Electrical and Computer Engineering, Athens 157 71 (Greece); Nikita, Alexandra [University of Athens, Medical School 152 28 Athens (Greece); Nikita, Konstantina S. [National Technical University of Athens, School of Electrical and Computer Engineering, Athens 157 71 (Greece)

    2006-12-20

    Advances in imaging technology and computer science have greatly enhanced interpretation of medical images, and contributed to early diagnosis. The typical architecture of a Computer Aided Diagnosis (CAD) system includes image pre-processing, definition of region(s) of interest, features extraction and selection, and classification. In this paper, the principles of CAD systems design and development are demonstrated by means of two examples. The first one focuses on the differentiation between symptomatic and asymptomatic carotid atheromatous plaques. For each plaque, a vector of texture and motion features was estimated, which was then reduced to the most robust ones by means of ANalysis of VAriance (ANOVA). Using fuzzy c-means, the features were then clustered into two classes. Clustering performances of 74%, 79%, and 84% were achieved for texture only, motion only, and combinations of texture and motion features, respectively. The second CAD system presented in this paper supports the diagnosis of focal liver lesions and is able to characterize liver tissue from Computed Tomography (CT) images as normal, hepatic cyst, hemangioma, and hepatocellular carcinoma. Five texture feature sets were extracted for each lesion, while a genetic algorithm based feature selection method was applied to identify the most robust features. The selected feature set was fed into an ensemble of neural network classifiers. The achieved classification performance was 100%, 93.75% and 90.63% in the training, validation and testing set, respectively. It is concluded that computerized analysis of medical images in combination with artificial intelligence can be used in clinical practice and may contribute to more efficient diagnosis.

  7. Intelligent systems

    CERN Document Server

    Irwin, J David

    2011-01-01

    Technology has now progressed to the point that intelligent systems are replacing humans in the decision making processes as well as aiding in the solution of very complex problems. In many cases intelligent systems are already outperforming human activities. Artificial neural networks are not only capable of learning how to classify patterns, such images or sequence of events, but they can also effectively model complex nonlinear systems. Their ability to classify sequences of events is probably more popular in industrial applications where there is an inherent need to model nonlinear system

  8. Advanced intelligent systems

    CERN Document Server

    Ryoo, Young; Jang, Moon-soo; Bae, Young-Chul

    2014-01-01

    Intelligent systems have been initiated with the attempt to imitate the human brain. People wish to let machines perform intelligent works. Many techniques of intelligent systems are based on artificial intelligence. According to changing and novel requirements, the advanced intelligent systems cover a wide spectrum: big data processing, intelligent control, advanced robotics, artificial intelligence and machine learning. This book focuses on coordinating intelligent systems with highly integrated and foundationally functional components. The book consists of 19 contributions that features social network-based recommender systems, application of fuzzy enforcement, energy visualization, ultrasonic muscular thickness measurement, regional analysis and predictive modeling, analysis of 3D polygon data, blood pressure estimation system, fuzzy human model, fuzzy ultrasonic imaging method, ultrasonic mobile smart technology, pseudo-normal image synthesis, subspace classifier, mobile object tracking, standing-up moti...

  9. Intelligent computational systems for space applications

    Science.gov (United States)

    Lum, Henry; Lau, Sonie

    Intelligent computational systems can be described as an adaptive computational system integrating both traditional computational approaches and artificial intelligence (AI) methodologies to meet the science and engineering data processing requirements imposed by specific mission objectives. These systems will be capable of integrating, interpreting, and understanding sensor input information; correlating that information to the "world model" stored within its data base and understanding the differences, if any; defining, verifying, and validating a command sequence to merge the "external world" with the "internal world model"; and, controlling the vehicle and/or platform to meet the scientific and engineering mission objectives. Performance and simulation data obtained to date indicate that the current flight processors baselined for many missions such as Space Station Freedom do not have the computational power to meet the challenges of advanced automation and robotics systems envisioned for the year 2000 era. Research issues which must be addressed to achieve greater than giga-flop performance for on-board intelligent computational systems have been identified, and a technology development program has been initiated to achieve the desired long-term system performance objectives.

  10. The Influence of Cochlear Mechanical Dysfunction, Temporal Processing Deficits, and Age on the Intelligibility of Audible Speech in Noise for Hearing-Impaired Listeners

    Directory of Open Access Journals (Sweden)

    Peter T. Johannesen

    2016-05-01

    Full Text Available The aim of this study was to assess the relative importance of cochlear mechanical dysfunction, temporal processing deficits, and age on the ability of hearing-impaired listeners to understand speech in noisy backgrounds. Sixty-eight listeners took part in the study. They were provided with linear, frequency-specific amplification to compensate for their audiometric losses, and intelligibility was assessed for speech-shaped noise (SSN and a time-reversed two-talker masker (R2TM. Behavioral estimates of cochlear gain loss and residual compression were available from a previous study and were used as indicators of cochlear mechanical dysfunction. Temporal processing abilities were assessed using frequency modulation detection thresholds. Age, audiometric thresholds, and the difference between audiometric threshold and cochlear gain loss were also included in the analyses. Stepwise multiple linear regression models were used to assess the relative importance of the various factors for intelligibility. Results showed that (a cochlear gain loss was unrelated to intelligibility, (b residual cochlear compression was related to intelligibility in SSN but not in a R2TM, (c temporal processing was strongly related to intelligibility in a R2TM and much less so in SSN, and (d age per se impaired intelligibility. In summary, all factors affected intelligibility, but their relative importance varied across maskers.

  11. Artificial intelligence in process control: Knowledge base for the shuttle ECS model

    Science.gov (United States)

    Stiffler, A. Kent

    1989-01-01

    The general operation of KATE, an artificial intelligence controller, is outlined. A shuttle environmental control system (ECS) demonstration system for KATE is explained. The knowledge base model for this system is derived. An experimental test procedure is given to verify parameters in the model.

  12. Joint Intelligence Operations Center (JIOC) Baseline Business Process Model & Capabilities Evaluation Methodology

    Science.gov (United States)

    2012-03-01

    Targeting Review Board OPLAN Operations Plan OPORD Operations Order OPSIT Operational Situation OSINT Open Source Intelligence OV...Analysis Evaluate FLTREPs MISREPs Unit Assign Assets Feedback Asset Shortfalls Multi-Int Collection Political & Embasy Law Enforcement HUMINT OSINT ...Embassy Information OSINT Manage Theater HUMINT Law Enforcement Collection Sort Requests Platform Information Agency Information M-I Collect

  13. Overview of the research and development on knowledge information processing and intelligent robots

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, K

    1982-04-01

    To implement intelligent computers, the problem of formalization of human intellectual activity must be considered. Insight into formalized intellectual activity can be gained by examination of its four abilities: (1) problem-solving; (2) learning, recognition and understanding; (3) language analysis and understanding; and (4) intellectual interaction. These are the topics discussed in the paper. 68 references.

  14. Overall comparative analysis of management and outcomes of cardiac cases reported on board merchant ships.

    Science.gov (United States)

    Apostolatos, Charalampos; Andria, Vivian; Licari, Julie

    Telemedical assistance has always been the cornerstone of medical care on board. Significant technological progress has provided improved scientific tools and equipment for high-quality communication and prompt management of either minor incidents or major emergencies on board. Med Solutions International is a medical management company, offering services exclusively to the maritime industry. Registered vessels contact the medical team and healthcare professionals provide immediate guidelines for onboard management as well as necessary action thereafter, i.e. examination ashore or urgent medical evacuation. Since cardiac conditions or diseases are potentially the most dangerous when traveling at sea, it is of major importance to analyse and evaluate the overall management and outcomes of cases reporting symptoms of possible heart disease so as to improve telemedical assistance services in future. The study included cases reporting cardiac symptoms from 5 major shipping companies during the year 2016. Data was collected from telecommunication, emails and seafarers' final medical reports. A descriptive analysis of overall management and outcomes was performed. The study showed that the number of confirmed cardiovascular cases on board was very low. Among 551 total cases and 44 cases with reported cardiac symptoms there was only one heart attack, one pulmonary oedema and one suspected myocarditis. In the majority of cases, chest pain was musculoskeletal or due to respiratory infection. Symptoms resulting from issues such as stress or anxiety often present as potential cardiac conditions. Stress may also amplify the severity of symptoms. Language barriers between the seafarer, the master and the doctor often make communication very difficult. According to our findings there are grounds to intensify the prevention process through more efficient pre-employment medical examinations and improve management on board through more intensive training. Communication problems

  15. APXS on board Chandrayaan-2 Rover

    Science.gov (United States)

    Shanmugam, M.; Sripada, V. S. Murty; Acharya, Y. B.; Goyal, S. K.

    2012-07-01

    Alpha Particle X-ray Spectrometer (APXS) is a well proven instrument for quantitative in situ elemental analysis of the planetary surfaces and has been successfully employed for Mars surface exploration. Chandrayaan-2, ISRO's second lunar mission having an Orbiter, Lander and Rover has provided an opportunity to explore the lunar surface with superior detectors such as Silicon Drift Detector (SDD) with energy resolution of about 150eV @ 5.9keV. The objective of the APXS instrument is to analyse several soil/rock samples along the rover traverse for the major elements with characteristic X-rays in 1 to 25keV range. The working principle of APXS involves measuring the intensity of characteristic X-rays emitted from the sample due to Alpha Particle Induced X-ray Emission (PIXE) and X-ray florescence (XRF) processes using suitable radioactive sources, allowing the determination of elements from Na to Br, spanning the energy range of 0.9 to 16keV. For this experiment ^{244}Cm radioactive source has been chosen which emits both Alpha particles (5.8MeV) and X-rays (14.1keV, 18keV). APXS uses six Alpha sources, each about 5mCi activity. Unlike Mars, lunar environment poses additional challenges due to the regolith and extreme surface temperature changes, to operate the APXS. Our APXS instrument consists of two packages namely APXS sensor head and APXS signal electronics. The sensor head assembly contains SDD, six alpha sources and front end electronic circuits such as preamplifier and shaper circuits and will be mounted on a robotic arm which on command brings the sensor head close to the lunar surface at a height of 35±10mm. SDD module to be used in the experiment has 30mm ^{2} active detector area with in-built peltier cooler and heat sink to maintain the detector at about -35°C. The detector is covered with 8 micron thick Be window which results in the low energy threshold of about 1keV. The size of the APXS sensor head is 70x70x70mm ^{3} (approx). APXS signal

  16. On-board system for physical and microphysical measurements

    International Nuclear Information System (INIS)

    Ravaut, M.; Allet, C.; Dole, B.; Gribkoff, A.; Schibler, P.; Charpentier, C.

    1981-10-01

    This report presents the system of physical and microphysical measurement instrumentation on board the HUREL-DUBOIS HD 34 aircraft, built in cooperation with the Institut National d'Astronomie et de Geophysique (I.N.A.G.) and the Institut Geographique National (I.G.N.). The feasibility study of the system was carried out in the first half of 1978 and took shape in an on-site proving campaign in November 1979. As a result, the on-board system was able to participate in the BUGEY experimental campaign of March 1980, a glimpse of which is given in this report [fr

  17. Intelligent Traffic Quantification System

    Science.gov (United States)

    Mohanty, Anita; Bhanja, Urmila; Mahapatra, Sudipta

    2017-08-01

    Currently, city traffic monitoring and controlling is a big issue in almost all cities worldwide. Vehicular ad-hoc Network (VANET) technique is an efficient tool to minimize this problem. Usually, different types of on board sensors are installed in vehicles to generate messages characterized by different vehicle parameters. In this work, an intelligent system based on fuzzy clustering technique is developed to reduce the number of individual messages by extracting important features from the messages of a vehicle. Therefore, the proposed fuzzy clustering technique reduces the traffic load of the network. The technique also reduces congestion and quantifies congestion.

  18. Machine listening intelligence

    Science.gov (United States)

    Cella, C. E.

    2017-05-01

    This manifesto paper will introduce machine listening intelligence, an integrated research framework for acoustic and musical signals modelling, based on signal processing, deep learning and computational musicology.

  19. Intelligent Optics Laboratory

    Data.gov (United States)

    Federal Laboratory Consortium — The Intelligent Optics Laboratory supports sophisticated investigations on adaptive and nonlinear optics; advancedimaging and image processing; ground-to-ground and...

  20. Platforme pour la collecte et l'exploitation efficaces et sécurisées de données dans les réseaux véhiculaires intelligents

    OpenAIRE

    Bouali , Tarek

    2016-01-01

    Nowadays, automotive area is witnessing a tremendous evolution due to the increasing growth in communication technologies, environmental sensing & perception aptitudes, and storage & processing capacities that we can find in recent vehicles. Indeed, a car is being a kind of intelligent mobile agent able to perceive its environment, sense and process data using on-board systems and interact with other vehicles or existing infrastructure. These advancements stimulate the development of several ...

  1. Artificial Intelligence Framework for Simulating Clinical Decision-Making: A Markov Decision Process Approach

    OpenAIRE

    Bennett, Casey C.; Hauser, Kris

    2013-01-01

    In the modern healthcare system, rapidly expanding costs/complexity, the growing myriad of treatment options, and exploding information streams that often do not effectively reach the front lines hinder the ability to choose optimal treatment decisions over time. The goal in this paper is to develop a general purpose (non-disease-specific) computational/artificial intelligence (AI) framework to address these challenges. This serves two potential functions: 1) a simulation environment for expl...

  2. Writing cases as a knowledge capture process in a competitive intelligence program

    OpenAIRE

    Mallowan , Monica; Marcon , Christian

    2009-01-01

    International audience; Students in Competitive Intelligence (CI) programs submit a report following their internship in an organisation. It is proposed that the result of their experiences be shared with their peers, in the form of cases written for in-class analysis. A knowledge base is thus created, which gradually becomes the program's memory and, by its constant renewal and connection with the reality, the most useful teaching tool for the professor.

  3. Dust analysis on board the Destiny+ mission to 3200 Phaethon

    Science.gov (United States)

    Krüger, H.; Kobayashi, M.; Arai, T.; Srama, R.; Sarli, B. V.; Kimura, H.; Moragas-Klostermeyer, G.; Soja, R.; Altobelli, N.; Grün, E.

    2017-09-01

    The Japanese Destiny+ spacecraft will be launched to the active asteroid 3200 Phaethon in 2022. Among the proposed core payload is an in-situ dust instrument based on the Cassini Cosmic Dust Analyzer. We use the ESA Interplanetary Meteoroid Engineering Model (IMEM), to study detection conditions and fluences of interplanetary and interstellar dust with a dust analyzer on board Destiny+.

  4. Digital tomosynthesis with an on-board kilovoltage imaging device

    International Nuclear Information System (INIS)

    Godfrey, Devon J.; Yin, F.-F.; Oldham, Mark; Yoo, Sua; Willett, Christopher

    2006-01-01

    Purpose: To generate on-board digital tomosynthesis (DTS) and reference DTS images for three-dimensional image-guided radiation therapy (IGRT) as an alternative to conventional portal imaging or on-board cone-beam computed tomography (CBCT). Methods and Materials: Three clinical cases (prostate, head-and-neck, and liver) were selected to illustrate the capabilities of on-board DTS for IGRT. Corresponding reference DTS images were reconstructed from digitally reconstructed radiographs computed from planning CT image sets. The effect of scan angle on DTS slice thickness was examined by computing the mutual information between coincident CBCT and DTS images, as the DTS scan angle was varied from 0 o to 165 o . A breath-hold DTS acquisition strategy was implemented to remove respiratory motion artifacts. Results: Digital tomosynthesis slices appeared similar to coincident CBCT planes and yielded substantially more anatomic information than either kilovoltage or megavoltage radiographs. Breath-hold DTS acquisition improved soft-tissue visibility by suppressing respiratory motion. Conclusions: Improved bony and soft-tissue visibility in DTS images is likely to improve target localization compared with radiographic verification techniques and might allow for daily localization of a soft-tissue target. Breath-hold DTS is a potential alternative to on-board CBCT for sites prone to respiratory motion

  5. Intelligence and treaty ratification

    International Nuclear Information System (INIS)

    Cahn, A.H.

    1990-01-01

    This paper reports that there are two sets of questions applicable to the ratification phase: what is the role of intelligence in the ratification process? What effect did intelligence have on that process. The author attempts to answer these and other questions

  6. Intelligible Artificial Intelligence

    OpenAIRE

    Weld, Daniel S.; Bansal, Gagan

    2018-01-01

    Since Artificial Intelligence (AI) software uses techniques like deep lookahead search and stochastic optimization of huge neural networks to fit mammoth datasets, it often results in complex behavior that is difficult for people to understand. Yet organizations are deploying AI algorithms in many mission-critical settings. In order to trust their behavior, we must make it intelligible --- either by using inherently interpretable models or by developing methods for explaining otherwise overwh...

  7. Development of on-board fuel metering and sensing system

    Science.gov (United States)

    Hemanth, Y.; Manikanta, B. S. S.; Thangaraja, J.; Bharanidaran, R.

    2017-11-01

    Usage of biodiesel fuels and their blends with diesel fuel has a potential to reduce the tailpipe emissions and reduce the dependence on crude oil imports. Further, biodiesel fuels exhibit favourable greenhouse gas emission and energy balance characteristics. While fossil fuel technology is well established, the technological implications of biofuels particularly biodiesel is not clearly laid out. Hence, the objective is to provide an on-board metering control in selecting the different proportions of diesel and bio-diesel blends. An on-board fuel metering system is being developed using PID controller, stepper motors and a capacitance sensor. The accuracy was tested with the blends of propanol-1, diesel and are found to be within 1.3% error. The developed unit was tested in a twin cylinder diesel engine with biodiesel blended diesel fuel. There was a marginal increase (5%) in nitric oxide and 14% increase in smoke emission with 10% biodiesel blended diesel at part load conditions.

  8. Passengers' perception of the safety demonstration on board an aircraft

    Science.gov (United States)

    Ruenruoy, Ratchada

    The cabin safety demonstration on board an aircraft is one of the methods to provide safety information for passengers before aircraft takeoff. However, passengers' enthusiasm toward safety demonstrations is normally low. Therefore, the study of passengers' perception toward safety briefings on board an aircraft is important in increasing the safety awareness for the travelling public on commercial aircraft. A survey was distributed to measure the perceptions of Middle Tennessee State University (MTSU) faculty and staff, Aerospace students, and international students who have traveled in the last year. It was generally found that watching the cabin safety demonstration before aircraft takeoff was believed to be important for passengers. However, the attention to the safety demonstration remained low because the safety briefings were not good enough in terms of clear communication, particularly in the recorded audio demonstration and the live safety demonstration methods of briefing.

  9. Reverse osmosis seawater test facility on board NS Otto Hahn

    International Nuclear Information System (INIS)

    Boeddeker, K.W.; Hilgendorff, W.; Kaschemekat, J.

    1977-01-01

    To evaluate the performance of reverse osmosis membranes and prototype modules for the desalination of sea water under near technical conditions, a test station has been installed on board the nuclear research vessel NS Otto Hahn. A newly designed plate module with variable membrane area and favorable membrane exchange properties is being used as a test instrument for membranes and operating conditions. (orig./HK) [de

  10. Female Institutional Directors on Boards and Firm Value

    OpenAIRE

    Pucheta Martínez, María Consuelo; Bel Oms, Inmaculada; Olcina Sempere, Gustau

    2016-01-01

    The aim of this research is to examine what impact female institutional directors on boards have on corporate performance. Previous research shows that institutional female directors cannot be considered as a homogeneous group since they represent investors who may or may not maintain business relations with the companies on whose corporate boards they sit. Thus, it is not only the effect of female institutional directors as a whole on firm value that has been analysed, but also the impact of...

  11. Second Harmonic Imaging improves Echocardiograph Quality on board the International Space Station

    Science.gov (United States)

    Garcia, Kathleen; Sargsyan, Ashot; Hamilton, Douglas; Martin, David; Ebert, Douglas; Melton, Shannon; Dulchavsky, Scott

    2008-01-01

    Ultrasound (US) capabilities have been part of the Human Research Facility (HRF) on board the International Space Station (ISS) since 2001. The US equipment on board the ISS includes a first-generation Tissue Harmonic Imaging (THI) option. Harmonic imaging (HI) is the second harmonic response of the tissue to the ultrasound beam and produces robust tissue detail and signal. Since this is a first-generation THI, there are inherent limitations in tissue penetration. As a breakthrough technology, HI extensively advanced the field of ultrasound. In cardiac applications, it drastically improves endocardial border detection and has become a common imaging modality. U.S. images were captured and stored as JPEG stills from the ISS video downlink. US images with and without harmonic imaging option were randomized and provided to volunteers without medical education or US skills for identification of endocardial border. The results were processed and analyzed using applicable statistical calculations. The measurements in US images using HI improved measurement consistency and reproducibility among observers when compared to fundamental imaging. HI has been embraced by the imaging community at large as it improves the quality and data validity of US studies, especially in difficult-to-image cases. Even with the limitations of the first generation THI, HI improved the quality and measurability of many of the downlinked images from the ISS and should be an option utilized with cardiac imaging on board the ISS in all future space missions.

  12. [Assessment of adaptation to on-board conditions on "The Ship for World Youth"].

    Science.gov (United States)

    Kuramoto, H; Kurabayashi, L; Yamato, H; Inamura, H

    1992-01-01

    The adaptation process of youth from 13 countries on board "The 3rd Ship for World Youth" cruise which was held from January 18 to March 20 in 1991 was analyzed. The age of almost all of the participants was in the 20's (average age was 24.9 yrs), and there were 103 participants (47 males, 56 females) from Japan, 171 participants (86 males, 85 females) from North, Middle and South America, and Oceanian countries for total of 274 participants (133 males, 141 females). The living environment on board differed significantly from daily living conditions of the participants, particularly due to the need to communicate in a foreign language, and to live in harmony with different cultures in a confinement situation, such that they were inevitably susceptible to various stressors. Among the participants there were some who needed psychiatric care and treatment. In order to assess quantitatively psychosomatic reactions to those stressors, a 28-item scaled GHQ (= General Health Questionnaire) assessment was performed four times on board with the following findings: 1. Highest scores were seen shortly after embarkment and decreased as the participants got accustomed to the living conditions on board. 2. The scores of the Japanese participants were higher than those of foreign participants, possibly indicating awkward adaptational skill on the part of Japanese participants especially during the first stage. 3. Japanese females scored slightly higher than Japanese males throughout the course of the program. 4. No clear difference in scores between Japanese participants aged under 25 y and over 26 y was observed. 5. A large proportion (77.3%) of Japanese participants had Y-G personality test results classifying them in the 'stable positive' group (D group). These participants had significantly lower scaled GHQ scores than those in the non-D group, indicating a high adaptational ability of D group participants.

  13. Thermoluminescent dose measurements on board Salyut type orbital stations

    International Nuclear Information System (INIS)

    Akatov, Yu.A.; Arkhangelskij, V.V.; Aleksandrov, A.P.

    1984-06-01

    A small, vibration- and shock-resistant thermoluminescent dosemeter (TLD) system - named PILLE - was developed for orbital stations at the Central Research Institute for Physics, Hungary, to measure the cosmic radiation dose on-board. The first on-board measurements with this system were performed by B. Farkas, the Hungarian astronaut, on the Salyut-6 space station in 1980. The same instrument was used by other crews in the following years. Doses measured at different sites in Salyut-6 are presented. The dose rates varied from 0.7 to 0.11 mGy.day -1 . After the first cosmic measurements, the system was further developed. The minimum detectable dose of the new TLD system is 1 μGy, i.e. less by one order of magnitude than that of the former system. The self-irradiation dose rate of the TLD bulbs is also reduced by more than an order of magnitude to 10 nGy.h -1 , by use of potassium-free glass for the bulb envelope. This new type of PILLE TLD system is currently on-board Salyut-7. The dose rates (0.12-0.23 mGy.day -1 ) measured in 1983 are presented in detail. (author)

  14. Principles of artificial intelligence

    CERN Document Server

    Nilsson, Nils J

    1980-01-01

    A classic introduction to artificial intelligence intended to bridge the gap between theory and practice, Principles of Artificial Intelligence describes fundamental AI ideas that underlie applications such as natural language processing, automatic programming, robotics, machine vision, automatic theorem proving, and intelligent data retrieval. Rather than focusing on the subject matter of the applications, the book is organized around general computational concepts involving the kinds of data structures used, the types of operations performed on the data structures, and the properties of th

  15. Understanding the Globalization of Intelligence

    DEFF Research Database (Denmark)

    Svendsen, Adam David Morgan

    "This book provides an introduction to the complexities of contemporary Western Intelligence and its dynamics during an era of globalization. Towards an understanding of the globalization of intelligence process, Svendsen focuses on the secretive phenomenon of international or foreign intelligence...... cooperation ('liaison'), as it occurs in both theory and practice. Reflecting a complex coexistence plurality of several different and overlapping concepts in action, the challenging process of the globalization of intelligence emerges as essential for complex issue management purposes during a globalized era...

  16. Understanding Genetic Breast Cancer Risk: Processing Loci of the BRCA Gist Intelligent Tutoring System.

    Science.gov (United States)

    Wolfe, Christopher R; Reyna, Valerie F; Widmer, Colin L; Cedillos-Whynott, Elizabeth M; Brust-Renck, Priscila G; Weil, Audrey M; Hu, Xiangen

    2016-07-01

    The BRCA Gist Intelligent Tutoring System helps women understand and make decisions about genetic testing for breast cancer risk. BRCA Gist is guided by Fuzzy-Trace Theory, (FTT) and built using AutoTutor Lite. It responds differently to participants depending on what they say. Seven tutorial dialogues requiring explanation and argumentation are guided by three FTT concepts: forming gist explanations in one's own words, emphasizing decision-relevant information, and deliberating the consequences of decision alternatives. Participants were randomly assigned to BRCA Gist , a control, or impoverished BRCA Gist conditions removing gist explanation dialogues, argumentation dialogues, or FTT images. All BRCA Gist conditions performed significantly better than controls on knowledge, comprehension, and risk assessment. Significant differences in knowledge, comprehension, and fine-grained dialogue analyses demonstrate the efficacy of gist explanation dialogues. FTT images significantly increased knowledge. Providing more elements in arguments against testing correlated with increased knowledge and comprehension.

  17. Pipeline defect prediction using long range ultrasonic testing and intelligent processing

    International Nuclear Information System (INIS)

    Dino Isa; Rajprasad Rajkumar

    2009-01-01

    This paper deals with efforts to improve nondestructive testing (NDT) techniques by using artificial intelligence in detecting and predicting pipeline defects such as cracks and wall thinning. The main emphasis here will be on the prediction of corrosion type defects rather than just detection after the fact. Long range ultrasonic testing will be employed, where a ring of piezoelectric transducers are used to generate torsional guided waves. Various defects such as cracks as well as corrosion under insulation (CUI) will be simulated on a test pipe. The machine learning algorithm known as the Support Vector Machine (SVM) will be used to predict and classify transducer signals using regression and large margin classification. Regression results show that the SVM is able to accurately predict future defects based on trends of previous defect. The classification performance was also exceptional showing a facility to detect defects at different depths as well as for distinguishing closely spaced defects. (author)

  18. Prototype interface facility for intelligent handling and processing of medical image and data

    Science.gov (United States)

    Lymberopoulos, Dimitris C.; Garantziotis, Giannis; Spiropoulos, Kostas V.; Kotsopoulos, Stavros A.; Goutis, Costas E.

    1993-06-01

    This paper introduces an interface facility (IF) developed within the overall framework of RACE research project. Due to the nature of the project which it has been focused in the Remote Medical Expert Consultation, the involvement of distances, the versatile user advocation and familiarity with newly introduced methods of medical diagnosis, considerable deficiencies can arise. The aim was to intelligently assist the user/physician by providing an ergonomic environment which would contain operational and functional deficiencies to the lowest possible levels. IF, energizes and activates system and application level commands and procedures along with the necessary exemplified and instructional help facilities, in order to concisely allow the user to interact with the system safely and easily at all levels.

  19. Supporting the personnel reliability decision-making process with artificial intelligence

    International Nuclear Information System (INIS)

    Harte, D.C.

    1991-01-01

    Recent legislation concerning personnel security has vastly increased the responsibility and accountability of the security manager. Access authorization, fitness for duty, and personnel security access programs require decisions regarding an individual's trustworthiness and reliability based on the findings of a background investigation. While these guidelines provide significant data and are useful as a tool, limited resources are available to the adjudicator of derogatory information on what is and is not acceptable in terms of granting access to sensitive areas of nuclear plants. The reason why one individual is deemed unacceptable and the next acceptable may be questioned and cause discriminatory accusations. This paper is continuation of discussion on workforce reliability, focusing on the use of artificial intelligence to support the decisions of a security manager. With this support, the benefit of previous decisions helps ensure consistent adjudication of background investigations

  20. Intelligent Monitoring System with High Temperature Distributed Fiberoptic Sensor for Power Plant Combustion Processes

    Energy Technology Data Exchange (ETDEWEB)

    Kwang Y. Lee; Stuart S. Yin; Andre Boehman

    2006-09-26

    The objective of the proposed work is to develop an intelligent distributed fiber optical sensor system for real-time monitoring of high temperature in a boiler furnace in power plants. Of particular interest is the estimation of spatial and temporal distributions of high temperatures within a boiler furnace, which will be essential in assessing and controlling the mechanisms that form and remove pollutants at the source, such as NOx. The basic approach in developing the proposed sensor system is three fold: (1) development of high temperature distributed fiber optical sensor capable of measuring temperatures greater than 2000 C degree with spatial resolution of less than 1 cm; (2) development of distributed parameter system (DPS) models to map the three-dimensional (3D) temperature distribution for the furnace; and (3) development of an intelligent monitoring system for real-time monitoring of the 3D boiler temperature distribution. Under Task 1, we have set up a dedicated high power, ultrafast laser system for fabricating in-fiber gratings in harsh environment optical fibers, successfully fabricated gratings in single crystal sapphire fibers by the high power laser system, and developed highly sensitive long period gratings (lpg) by electric arc. Under Task 2, relevant mathematical modeling studies of NOx formation in practical combustors have been completed. Studies show that in boiler systems with no swirl, the distributed temperature sensor may provide information sufficient to predict trends of NOx at the boiler exit. Under Task 3, we have investigated a mathematical approach to extrapolation of the temperature distribution within a power plant boiler facility, using a combination of a modified neural network architecture and semigroup theory. Given a set of empirical data with no analytic expression, we first developed an analytic description and then extended that model along a single axis.

  1. An Integrated Architecture for On-Board Aircraft Engine Performance Trend Monitoring and Gas Path Fault Diagnostics

    Science.gov (United States)

    Simon, Donald L.

    2010-01-01

    Aircraft engine performance trend monitoring and gas path fault diagnostics are closely related technologies that assist operators in managing the health of their gas turbine engine assets. Trend monitoring is the process of monitoring the gradual performance change that an aircraft engine will naturally incur over time due to turbomachinery deterioration, while gas path diagnostics is the process of detecting and isolating the occurrence of any faults impacting engine flow-path performance. Today, performance trend monitoring and gas path fault diagnostic functions are performed by a combination of on-board and off-board strategies. On-board engine control computers contain logic that monitors for anomalous engine operation in real-time. Off-board ground stations are used to conduct fleet-wide engine trend monitoring and fault diagnostics based on data collected from each engine each flight. Continuing advances in avionics are enabling the migration of portions of the ground-based functionality on-board, giving rise to more sophisticated on-board engine health management capabilities. This paper reviews the conventional engine performance trend monitoring and gas path fault diagnostic architecture commonly applied today, and presents a proposed enhanced on-board architecture for future applications. The enhanced architecture gains real-time access to an expanded quantity of engine parameters, and provides advanced on-board model-based estimation capabilities. The benefits of the enhanced architecture include the real-time continuous monitoring of engine health, the early diagnosis of fault conditions, and the estimation of unmeasured engine performance parameters. A future vision to advance the enhanced architecture is also presented and discussed

  2. Intelligent Tutor

    Science.gov (United States)

    1990-01-01

    NASA also seeks to advance American education by employing the technology utilization process to develop a computerized, artificial intelligence-based Intelligent Tutoring System (ITS) to help high school and college physics students. The tutoring system is designed for use with the lecture and laboratory portions of a typical physics instructional program. Its importance lies in its ability to observe continually as a student develops problem solutions and to intervene when appropriate with assistance specifically directed at the student's difficulty and tailored to his skill level and learning style. ITS originated as a project of the Johnson Space Center (JSC). It is being developed by JSC's Software Technology Branch in cooperation with Dr. R. Bowen Loftin at the University of Houston-Downtown. Program is jointly sponsored by NASA and ACOT (Apple Classrooms of Tomorrow). Other organizations providing support include Texas Higher Education Coordinating Board, the National Research Council, Pennzoil Products Company and the George R. Brown Foundation. The Physics I class of Clear Creek High School, League City, Texas are providing the classroom environment for test and evaluation of the system. The ITS is a spinoff product developed earlier to integrate artificial intelligence into training/tutoring systems for NASA astronauts flight controllers and engineers.

  3. Artificial intelligence

    CERN Document Server

    Hunt, Earl B

    1975-01-01

    Artificial Intelligence provides information pertinent to the fundamental aspects of artificial intelligence. This book presents the basic mathematical and computational approaches to problems in the artificial intelligence field.Organized into four parts encompassing 16 chapters, this book begins with an overview of the various fields of artificial intelligence. This text then attempts to connect artificial intelligence problems to some of the notions of computability and abstract computing devices. Other chapters consider the general notion of computability, with focus on the interaction bet

  4. Intelligent mechatronics; Intelligent mechatronics

    Energy Technology Data Exchange (ETDEWEB)

    Hashimoto, H. [The University of Tokyo, Tokyo (Japan). Institute of Industrial Science

    1995-10-01

    Intelligent mechatronics (IM) was explained as follows: a study of IM essentially targets realization of a robot namely, but in the present stage the target is a creation of new values by intellectualization of machine, that is, a combination of the information infrastructure and the intelligent machine system. IM is also thought to be constituted of computers positively used and micromechatronics. The paper next introduces examples of IM study, mainly those the author is concerned with as shown below: sensor gloves, robot hands, robot eyes, tele operation, three-dimensional object recognition, mobile robot, magnetic bearing, construction of remote controlled unmanned dam, robot network, sensitivity communication using neuro baby, etc. 27 figs.

  5. The National Air Intelligence Center Software Process Improvement Effort (NAIC SPI)

    National Research Council Canada - National Science Library

    Blankenship, Donald

    2001-01-01

    ...) Software Process Improvements effort. The objective of this effort was for the contractor to provide engineering and software process improvement for NAIC/SCD to reach SEI's CMM Level 2 in process maturity...

  6. Service-oriented architecture of adaptive, intelligent data acquisition and processing systems for long-pulse fusion experiments

    International Nuclear Information System (INIS)

    Gonzalez, J.; Ruiz, M.; Barrera, E.; Lopez, J.M.; Arcas, G. de; Vega, J.

    2010-01-01

    The data acquisition systems used in long-pulse fusion experiments need to implement data reduction and pattern recognition algorithms in real time. In order to accomplish these operations, it is essential to employ software tools that allow for hot swap capabilities throughout the temporal evolution of the experiments. This is very important because processing needs are not equal during different phases of the experiment. The intelligent test and measurement system (ITMS) developed by UPM and CIEMAT is an example of a technology for implementing scalable data acquisition and processing systems based on PXI and CompactPCI hardware. In the ITMS platform, a set of software tools allows the user to define the processing algorithms associated with the different experimental phases using state machines driven by software events. These state machines are specified using the State Chart XML (SCXML) language. The software tools are developed using JAVA, JINI, an SCXML engine and several LabVIEW applications. Within this schema, it is possible to execute data acquisition and processing applications in an adaptive way. The power of SCXML semantics and the ability to work with XML user-defined data types allow for very easy programming of the ITMS platform. With this approach, the ITMS platform is a suitable solution for implementing scalable data acquisition and processing systems based on a service-oriented model with the ability to easily implement remote participation applications.

  7. Services oriented architecture for adaptive and intelligent data acquisition and processing systems in long pulse fusion experiments

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez, J.; Ruiz, M.; Barrera, E.; Lopez, J.M.; De Arcas, G. [Universidad Politecnica de Madrid (Spain); Vega, J. [Association EuratomCIEMAT para Fusion, Madrid (Spain)

    2009-07-01

    Data acquisition systems used in long pulse fusion experiments require to implement data reduction and pattern recognition algorithms in real time. In order to accomplish these operations is essential to dispose software tools that allow hot swap capabilities throughout the temporal evolution of the experiments. This is very important because the processing needs are not equal in the different experiment's phases. The intelligent test and measurement system (ITMS) developed by UPM and CIEMAT is an example of technology for implementing scalable data acquisition and processing systems based in PXI and compact PCI hardware. In the ITMS platform a set of software tools allows the user to define the processing associated with the different experiment's phases using state machines driven by software events. These state machines are specified using State Chart XML (SCXML) language. The software tools are developed using: JAVA, JINI, a SCXML engine and several LabVIEW applications. With this schema it is possible to execute data acquisition and processing applications in an adaptive way. The powerful of SCXML semantics and the possibility of to work with XML user defined data types allow a very easy programming of ITMS platform. With this approach ITMS platform is a suitable solution for implementing scalable data acquisition and processing systems, based in a services oriented model, with ease possibility for implement remote participation applications. (authors)

  8. Service-oriented architecture of adaptive, intelligent data acquisition and processing systems for long-pulse fusion experiments

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez, J. [Grupo de Investigacion en Instrumentacion y Acustica Aplicada. Universidad Politecnica de Madrid, Crta. Valencia Km-7 Madrid 28031 (Spain); Ruiz, M., E-mail: mariano.ruiz@upm.e [Grupo de Investigacion en Instrumentacion y Acustica Aplicada. Universidad Politecnica de Madrid, Crta. Valencia Km-7 Madrid 28031 (Spain); Barrera, E.; Lopez, J.M.; Arcas, G. de [Grupo de Investigacion en Instrumentacion y Acustica Aplicada. Universidad Politecnica de Madrid, Crta. Valencia Km-7 Madrid 28031 (Spain); Vega, J. [Asociacion EURATOM/CIEMAT para Fusion, Madrid (Spain)

    2010-07-15

    The data acquisition systems used in long-pulse fusion experiments need to implement data reduction and pattern recognition algorithms in real time. In order to accomplish these operations, it is essential to employ software tools that allow for hot swap capabilities throughout the temporal evolution of the experiments. This is very important because processing needs are not equal during different phases of the experiment. The intelligent test and measurement system (ITMS) developed by UPM and CIEMAT is an example of a technology for implementing scalable data acquisition and processing systems based on PXI and CompactPCI hardware. In the ITMS platform, a set of software tools allows the user to define the processing algorithms associated with the different experimental phases using state machines driven by software events. These state machines are specified using the State Chart XML (SCXML) language. The software tools are developed using JAVA, JINI, an SCXML engine and several LabVIEW applications. Within this schema, it is possible to execute data acquisition and processing applications in an adaptive way. The power of SCXML semantics and the ability to work with XML user-defined data types allow for very easy programming of the ITMS platform. With this approach, the ITMS platform is a suitable solution for implementing scalable data acquisition and processing systems based on a service-oriented model with the ability to easily implement remote participation applications.

  9. Fish radurization on board of mediterranean fishing boats

    International Nuclear Information System (INIS)

    Leonardi, M.; Tata, A.

    1988-01-01

    The paper presents the results of a feasibility-study carrie out by ENEA with the technical support of ICRAP. Owing to its conclusions, the authors can locate some areas of possible application of fish-radurization both for the inner and for the foreign market. The former may offer in particular the opportunity of the on-board radurization, because of its peculiar characteristics. The latter may be particularly receptive in the case of those countries where refrigerating line is lacking and where the distribution of fresh fish-products seems rather difficult

  10. On-board image compression for the RAE lunar mission

    Science.gov (United States)

    Miller, W. H.; Lynch, T. J.

    1976-01-01

    The requirements, design, implementation, and flight performance of an on-board image compression system for the lunar orbiting Radio Astronomy Explorer-2 (RAE-2) spacecraft are described. The image to be compressed is a panoramic camera view of the long radio astronomy antenna booms used for gravity-gradient stabilization of the spacecraft. A compression ratio of 32 to 1 is obtained by a combination of scan line skipping and adaptive run-length coding. The compressed imagery data are convolutionally encoded for error protection. This image compression system occupies about 1000 cu cm and consumes 0.4 W.

  11. Applying CASE Tools for On-Board Software Development

    Science.gov (United States)

    Brammer, U.; Hönle, A.

    For many space projects the software development is facing great pressure with respect to quality, costs and schedule. One way to cope with these challenges is the application of CASE tools for automatic generation of code and documentation. This paper describes two CASE tools: Rhapsody (I-Logix) featuring UML and ISG (BSSE) that provides modeling of finite state machines. Both tools have been used at Kayser-Threde in different space projects for the development of on-board software. The tools are discussed with regard to the full software development cycle.

  12. Dual cell conductivity during ionic exchange processes: the intelligent transmitter EXA DC 400

    International Nuclear Information System (INIS)

    Mier, A.

    1997-01-01

    Why is differential conductivity important versus standard conductivity measurement? That entirely depends on the application. If we have a process where the conductivity changes ge.. Cation exchanger, then standard conductivity measurement is not appropriate. With dual cell conductivity we can rate the process and eliminate conductivity changes outside the process. Therefore we achieve more precise control or monitoring of that process. (Author)

  13. Dental ethics and emotional intelligence.

    Science.gov (United States)

    Rosenblum, Alvin B; Wolf, Steve

    2014-01-01

    Dental ethics is often taught, viewed, and conducted as an intell enterprise, uninformed by other noncognitive factors. Emotional intelligence (EQ) is defined distinguished from the cognitive intelligence measured by Intelligence Quotient (IQ). This essay recommends more inclusion of emotional, noncognitive input to the ethical decision process in dental education and dental practice.

  14. Artificial Intelligence and Moral intelligence

    OpenAIRE

    Laura Pana

    2008-01-01

    We discuss the thesis that the implementation of a moral code in the behaviour of artificial intelligent systems needs a specific form of human and artificial intelligence, not just an abstract intelligence. We present intelligence as a system with an internal structure and the structural levels of the moral system, as well as certain characteristics of artificial intelligent agents which can/must be treated as 1- individual entities (with a complex, specialized, autonomous or selfdetermined,...

  15. HTML 5 Displays for On-Board Flight Systems

    Science.gov (United States)

    Silva, Chandika

    2016-01-01

    During my Internship at NASA in the summer of 2016, I was assigned to a project which dealt with developing a web-server that would display telemetry and other system data using HTML 5, JavaScript, and CSS. By doing this, it would be possible to view the data across a variety of screen sizes, and establish a standard that could be used to simplify communication and software development between NASA and other countries. Utilizing a web- approach allowed us to add in more functionality, as well as make the displays more aesthetically pleasing for the users. When I was assigned to this project my main task was to first establish communication with the current display server. This display server would output data from the on-board systems in XML format. Once communication was established I was then asked to create a dynamic telemetry table web page that would update its header and change as new information came in. After this was completed, certain minor functionalities were added to the table such as a hide column and filter by system option. This was more for the purpose of making the table more useful for the users, as they can now filter and view relevant data. Finally my last task was to create a graphical system display for all the systems on the space craft. This was by far the most challenging part of my internship as finding a JavaScript library that was both free and contained useful functions to assist me in my task was difficult. In the end I was able to use the JointJs library and accomplish the task. With the help of my mentor and the HIVE lab team, we were able to establish stable communication with the display server. We also succeeded in creating a fully dynamic telemetry table and in developing a graphical system display for the advanced modular power system. Working in JSC for this internship has taught me a lot about coding in JavaScript and HTML 5. I was also introduced to the concept of developing software as a team, and exposed to the different

  16. The Acquisition of Context Data of Study Process and their Application in Classroom and Intelligent Tutoring Systems

    Directory of Open Access Journals (Sweden)

    Bicans Janis

    2015-12-01

    Full Text Available Over the last decade, researchers are investigating the potential of the educational paradigm shift from the traditional “one-size-fits all” teaching approach to an adaptive and more personalized study process. Availability of fast mobile connections along with the portative handheld device evolution, like phones and tablets, enable teachers and learners to communicate and interact with each other in a completely different way and speed. The mentioned devices not only deliver tutoring material to the learner, but might also serve as sensors to provide data about the learning process itself, e.g., learning conditions, location, detailed information on learning of tutoring material and other information. This sensor data put into the context of the study process can be widely used to improve student experience in the classroom and e-learning by providing more precise and detailed information to the teacher and/or an intelligent tutoring system for the selection of an appropriate tutoring strategy. This paper analyses and discusses acquisition, processing, and application scenarios of contextual information.

  17. On-board aircrew dosimetry using a semiconductor spectrometer

    CERN Document Server

    Spurny, F

    2002-01-01

    Radiation fields on board aircraft contain particles with energies up to a few hundred MeV. Many instruments have been tested to characterise these fields. This paper presents the results of studies on the use of an Si diode spectrometer to characterise these fields. The spectrometer has been in use since spring 2000 on more than 130 return flights to monitor and characterise the on-board field. During a Czech Airlines flight from Prague to New York it was possible to register the effects of an intense solar flare, (ground level event, GLE 60), which occurred on 15 April 2001. It was found that the number of deposition events registered was increased by about 70% and the dose in Si by a factor of 2.0 when compared with the presence of galactic cosmic rays alone. Directly measured data are interpreted with respect to on-earth reference field calibration (photons, CERN high-energy particles); it was found that this approach leads to encouraging results and should be followed up. (7 refs).

  18. Trends in ambient intelligent systems the role of computational intelligence

    CERN Document Server

    Khan, Mohammad; Abraham, Ajith

    2016-01-01

    This book demonstrates the success of Ambient Intelligence in providing possible solutions for the daily needs of humans. The book addresses implications of ambient intelligence in areas of domestic living, elderly care, robotics, communication, philosophy and others. The objective of this edited volume is to show that Ambient Intelligence is a boon to humanity with conceptual, philosophical, methodical and applicative understanding. The book also aims to schematically demonstrate developments in the direction of augmented sensors, embedded systems and behavioral intelligence towards Ambient Intelligent Networks or Smart Living Technology. It contains chapters in the field of Ambient Intelligent Networks, which received highly positive feedback during the review process. The book contains research work, with in-depth state of the art from augmented sensors, embedded technology and artificial intelligence along with cutting-edge research and development of technologies and applications of Ambient Intelligent N...

  19. Individual differences in working memory, secondary memory, and fluid intelligence: evidence from the levels-of-processing span task.

    Science.gov (United States)

    Rose, Nathan S

    2013-12-01

    Individual differences in working memory (WM) are related to performance on secondary memory (SM), and fluid intelligence (gF) tests. However, the source of the relation remains unclear, in part because few studies have controlled for the nature of encoding; therefore, it is unclear whether individual variation is due to encoding, maintenance, or retrieval processes. In the current study, participants performed a WM task (the levels-of-processing span task; Rose, Myerson, Roediger III, & Hale, 2010) and a SM test that tested for both targets and the distracting processing words from the initial WM task. Deeper levels of processing at encoding did not benefit WM, but did benefit subsequent SM, although the amount of benefit was smaller for those with lower WM spans. This result suggests that, despite encoding cues that facilitate retrieval from SM, low spans may have engaged in shallower, maintenance-focused processing to maintain the words in WM. Low spans also recalled fewer targets, more distractors, and more extralist intrusions than high spans, although this was partially due to low spans' poorer recall of targets, which resulted in a greater number of opportunities to commit recall errors. Delayed recall of intrusions and commission of source errors (labeling targets as processing words and vice versa) were significant negative predictors of gF. These results suggest that the ability to use source information to recall relevant information and withhold recall of irrelevant information is a critical source of both individual variation in WM and the relation between WM, SM, and gF. (PsycINFO Database Record (c) 2013 APA, all rights reserved).

  20. Monitoring the Microgravity Environment Quality On-Board the International Space Station Using Soft Computing Techniques

    Science.gov (United States)

    Jules, Kenol; Lin, Paul P.

    2001-01-01

    This paper presents an artificial intelligence monitoring system developed by the NASA Glenn Principal Investigator Microgravity Services project to help the principal investigator teams identify the primary vibratory disturbance sources that are active, at any moment in time, on-board the International Space Station, which might impact the microgravity environment their experiments are exposed to. From the Principal Investigator Microgravity Services' web site, the principal investigator teams can monitor via a graphical display, in near real time, which event(s) is/are on, such as crew activities, pumps, fans, centrifuges, compressor, crew exercise, platform structural modes, etc., and decide whether or not to run their experiments based on the acceleration environment associated with a specific event. This monitoring system is focused primarily on detecting the vibratory disturbance sources, but could be used as well to detect some of the transient disturbance sources, depending on the events duration. The system has built-in capability to detect both known and unknown vibratory disturbance sources. Several soft computing techniques such as Kohonen's Self-Organizing Feature Map, Learning Vector Quantization, Back-Propagation Neural Networks, and Fuzzy Logic were used to design the system.

  1. An evolutionary approach for business process redesign : towards an intelligent system

    NARCIS (Netherlands)

    Netjes, M.; Limam Mansar, S.; Reijers, H.A.; Aalst, van der W.M.P.; Cardoso, J.; Cordeiro, J.; Filipe, J.

    2007-01-01

    Although extensive literature on BPR is available, there is still a lack of concrete guidance on actually changing processes for the better. It is our goal to provide a redesign approach which describes and supports the steps to derive from an existing process a better performing redesign. In this

  2. Supporting the full BPM life-cycle using process mining and intelligent redesign

    NARCIS (Netherlands)

    Netjes, M.; Reijers, H.A.; Aalst, van der W.M.P.; Siau, K.

    2007-01-01

    Abstract. Business Process Management (BPM) systems provide a broad range of facilities to enact and manage operational business processes. Ideally, these systems should provide support for the complete BPM life-cycle: (re)design, configuration, execution, control, and diagnosis by the FileNet P8

  3. Bio-inspired Artificial Intelligence: А Generalized Net Model of the Regularization Process in MLP

    Directory of Open Access Journals (Sweden)

    Stanimir Surchev

    2013-10-01

    Full Text Available Many objects and processes inspired by the nature have been recreated by the scientists. The inspiration to create a Multilayer Neural Network came from human brain as member of the group. It possesses complicated structure and it is difficult to recreate, because of the existence of too many processes that require different solving methods. The aim of the following paper is to describe one of the methods that improve learning process of Artificial Neural Network. The proposed generalized net method presents Regularization process in Multilayer Neural Network. The purpose of verification is to protect the neural network from overfitting. The regularization is commonly used in neural network training process. Many methods of verification are present, the subject of interest is the one known as Regularization. It contains function in order to set weights and biases with smaller values to protect from overfitting.

  4. Shifts in information processing level: the speed theory of intelligence revisited.

    Science.gov (United States)

    Sircar, S S

    2000-06-01

    A hypothesis is proposed here to reconcile the inconsistencies observed in the IQ-P3 latency relation. The hypothesis stems from the observation that task-induced increase in P3 latency correlates positively with IQ scores. It is hypothesised that: (a) there are several parallel information processing pathways of varying complexity which are associated with the generation of P3 waves of varying latencies; (b) with increasing workload, there is a shift in the 'information processing level' through progressive recruitment of more complex polysynaptic pathways with greater processing power and inhibition of the oligosynaptic pathways; (c) high-IQ subjects have a greater reserve of higher level processing pathways; (d) a given 'task-load' imposes a greater 'mental workload' in subjects with lower IQ than in those with higher IQ. According to this hypothesis, a meaningful comparison of the P3 correlates of IQ is possible only when the information processing level is pushed to its limits.

  5. Single-mode glass waveguide technology for optical interchip communication on board level

    Science.gov (United States)

    Brusberg, Lars; Neitz, Marcel; Schröder, Henning

    2012-01-01

    The large bandwidth demand in long-distance telecom networks lead to single-mode fiber interconnects as result of low dispersion, low loss and dense wavelength multiplexing possibilities. In contrast, multi-mode interconnects are suitable for much shorter lengths up to 300 meters and are promising for optical links between racks and on board level. Active optical cables based on multi-mode fiber links are at the market and research in multi-mode waveguide integration on board level is still going on. Compared to multi-mode, a single-mode waveguide has much more integration potential because of core diameters of around 20% of a multi-mode waveguide by a much larger bandwidth. But light coupling in single-mode waveguides is much more challenging because of lower coupling tolerances. Together with the silicon photonics technology, a single-mode waveguide technology on board-level will be the straight forward development goal for chip-to-chip optical interconnects integration. Such a hybrid packaging platform providing 3D optical single-mode links bridges the gap between novel photonic integrated circuits and the glass fiber based long-distance telecom networks. Following we introduce our 3D photonic packaging approach based on thin glass substrates with planar integrated optical single-mode waveguides for fiber-to-chip and chip-to-chip interconnects. This novel packaging approach merges micro-system packaging and glass integrated optics. It consists of a thin glass substrate with planar integrated singlemode waveguide circuits, optical mirrors and lenses providing an integration platform for photonic IC assembly and optical fiber interconnect. Thin glass is commercially available in panel and wafer formats and characterizes excellent optical and high-frequency properties. That makes it perfect for microsystem packaging. The paper presents recent results in single-mode waveguide technology on wafer level and waveguide characterization. Furthermore the integration in a

  6. The end-to-end testbed of the optical metrology system on-board LISA Pathfinder

    Energy Technology Data Exchange (ETDEWEB)

    Steier, F; Cervantes, F Guzman; Marin, A F GarcIa; Heinzel, G; Danzmann, K [Max-Planck-Institut fuer Gravitationsphysik (Albert-Einstein-Institut) and Universitaet Hannover (Germany); Gerardi, D, E-mail: frank.steier@aei.mpg.d [EADS Astrium Satellites GmbH, Friedrichshafen (Germany)

    2009-05-07

    LISA Pathfinder is a technology demonstration mission for the Laser Interferometer Space Antenna (LISA). The main experiment on-board LISA Pathfinder is the so-called LISA Technology Package (LTP) which has the aim to measure the differential acceleration between two free-falling test masses with an accuracy of 3 x 10{sup -14} ms{sup -2} Hz{sup -1/2} between 1 mHz and 30 mHz. This measurement is performed interferometrically by the optical metrology system (OMS) on-board LISA Pathfinder. In this paper, we present the development of an experimental end-to-end testbed of the entire OMS. It includes the interferometer and its sub-units, the interferometer backend which is a phasemeter and the processing of the phasemeter output data. Furthermore, three-axes piezo-actuated mirrors are used instead of the free-falling test masses for the characterization of the dynamic behaviour of the system and some parts of the drag-free and attitude control system (DFACS) which controls the test masses and the satellite. The end-to-end testbed includes all parts of the LTP that can reasonably be tested on earth without free-falling test masses. At its present status it consists mainly of breadboard components. Some of those have already been replaced by engineering models of the LTP experiment. In the next steps, further engineering and flight models will also be inserted in this testbed and tested against well-characterized breadboard components. The presented testbed is an important reference for the unit tests and can also be used for validation of the on-board experiment during the mission.

  7. Towards Intelligent Supply Chains

    DEFF Research Database (Denmark)

    Siurdyban, Artur; Møller, Charles

    2012-01-01

    applied to the context of organizational processes can increase the success rate of business operations. The framework is created using a set of theoretical based constructs grounded in a discussion across several streams of research including psychology, pedagogy, artificial intelligence, learning...... of deploying inapt operations leading to deterioration of profits. To address this problem, we propose a unified business process design framework based on the paradigm of intelligence. Intelligence allows humans and human-designed systems cope with environmental volatility, and we argue that its principles......, business process management and supply chain management. It outlines a number of system tasks combined in four integrated management perspectives: build, execute, grow and innovate, put forward as business process design propositions for Intelligent Supply Chains....

  8. Why so few Women on Boards of Directors?

    DEFF Research Database (Denmark)

    Smith, Nina; Parrotta, Pierpaolo

    2015-01-01

    This paper analyzes the determinants of women’s representation on boards of directors based on a panel of all privately owned or listed Danish firms with at least 50 employees observed during the period 1998–2010. We focus on the directors who are not elected by the employees and test three...... nonemployee-elected female board members. We also find clear evidence of a tokenism behavior in Danish companies. The likelihood of enlarging the share of non-employee-elected female board members is significantly smaller if one, two, or more women have sat on the board of directors. Finally, the pipeline...... suggests that an important way to increase the female proportion of non-employee-elected board members is that more women reach top executive positions....

  9. Monitoring on board spacecraft by means of passive detectors

    International Nuclear Information System (INIS)

    Ambrozova, I.; Brabcova, K.; Spurny, F.; Shurshakov, V. A.; Kartsev, I. S.; Tolochek, R. V.

    2011-01-01

    To estimate the radiation risk of astronauts during space missions, it is necessary to measure dose characteristics in various compartments of the spacecraft; this knowledge can be further used for estimating the health hazard in planned missions. This contribution presents results obtained during several missions on board the International Space Station (ISS) during 2005-09. A combination of thermoluminescent and plastic nuclear track detectors was used to measure the absorbed dose and dose equivalent. These passive detectors have several advantages, especially small dimensions, which enabled their placement at various locations in different compartments inside the ISS or inside the phantom. Variation of dosimetric quantities with the phase of the solar cycle and the position inside the ISS is discussed. (authors)

  10. Artificial Intelligence.

    Science.gov (United States)

    Information Technology Quarterly, 1985

    1985-01-01

    This issue of "Information Technology Quarterly" is devoted to the theme of "Artificial Intelligence." It contains two major articles: (1) Artificial Intelligence and Law" (D. Peter O'Neill and George D. Wood); (2) "Artificial Intelligence: A Long and Winding Road" (John J. Simon, Jr.). In addition, it contains two sidebars: (1) "Calculating and…

  11. Comparison of MODIS and VIIRS On-board Blackbody Performance

    Science.gov (United States)

    Xiong, Jack; Butler, Jim; Wu, Aisheng; Chiang, Vincent; McIntire, Jeff; Oudari, Hassan

    2012-01-01

    MODIS has 16 thermal emissive bands (TEBs), covering wavelengths from 3.7 to 14.4 microns. MODIS TEBs are calibrated on-orbit by a v-grooved blackbody (BB) on a scan-by-scan basis. The BB temperatures are measured by a set of 12 thennistors. As expected, the BB temperature uncertainty and stability have direct impact on the quality of TEB calibration and, therefore, the quality of the science products derived from TEB observations. Since launch, Terra and Aqua MODIS have successfully operated for more than 12 and 10 years, respectively. Their on-board BB performance has been satisfactory in meeting the TEB calibration requirements. The first VIIRS, launched on-board the Suomi NPP spacecraft on October 28, 2011, has successfully completed its initial Intensive Calibration and Validation (ICV) phase. VIIRS has 7 thermal emissive bands (TEBs), covering wavelengths from 3.7 to 12.4 microns. Designed with strong MODIS heritage, VIIRS uses a similar BB for its TEB calibration. Like MODIS, VIIRS BB is nominally controlled at a pre-determined temperature (set point). Periodically, a BB Warm-Up and Cool-Down (WUCD) operation is performed, during which the BB temperatures vary from instrument ambient (temperature) to 315K. This paper examines NPP VIIRS BB on-orbit performance. It focuses on its BB temperature scan-to-scan variations at nominally controlled temperature as well as during its WUCD operation and their impact on TEB calibration uncertainty. Comparisons of VIIRS (NPP) and MODIS (Terra and Aqua) BB on-orbit performance and lessons learned for future improvements are also presented in this paper.

  12. Predictive NO x emission monitoring on board a passenger ferry

    Science.gov (United States)

    Cooper, D. A.; Andreasson, K.

    NO x emissions from a medium speed diesel engine on board a servicing passenger ferry have been indirectly measured using a predictive emission monitoring system (PEMS) over a 1-yr period. Conventional NO x measurements were carried out with a continuous emission monitoring system (CEMS) at the start of the study to provide historical data for the empirical PEMS function. On three other occasions during the year the CEMS was also used to verify the PEMS and follow any changes in emission signature of the engine. The PEMS consisted of monitoring exhaust O 2 concentrations (in situ electrochemical probe), engine load, combustion air temperature and humidity, and barometric pressure. Practical experiences with the PEMS equipment were positive and measurement data were transferred to a land-based office by using a modem data communication system. The initial PEMS function (PEMS1) gave systematic differences of 1.1-6.9% of the calibration domain (0-1725 ppm) and a relative accuracy of 6.7% when compared with CEMS for whole journeys and varying load situations. Further improvements on the performance could be obtained by updating this function. The calculated yearly emission for a total engine running time of 4618 h was 316 t NO x±38 t and the average NO x emission corrected for ambient conditions 14.3 g kWh corr-1. The exhaust profile of the engine in terms of NO x, CO and CO 2 emissions as determined by CEMS was similar for most of the year. Towards the end of the study period, a significantly lower NO x emission was detected which was probably caused by replacement of fuel injector nozzles. The study suggests that PEMS can be a viable option for continuous, long-term NO x measurements on board ships.

  13. Predictive NOx emission monitoring on board a passenger ferry

    International Nuclear Information System (INIS)

    Cooper, D.A.; Andreasson, K.

    1999-01-01

    NO x emissions from a medium speed diesel engine on board a servicing passenger ferry have been indirectly measured using a predictive emission monitoring system (PEMS) over a 1-yr period. Conventional NO x measurements were carried out with a continuous emission monitoring system (CEMS) at the start of the study to provide historical data for the empirical PEMS function. On three other occasions during the year the CEMS was also used to verify the PEMS and follow any changes in emission signature of the engine. The PEMS consisted of monitoring exhaust O 2 concentrations (in situ electrochemical probe), engine load, combustion air temperature and humidity, and barometric pressure. Practical experiences with the PEMS equipment were positive and measurement data were transferred to a land-based office by using a modem data communication system. The initial PEMS function (PEMS1) gave systematic differences of 1.1-6.9% of the calibration domain (0-1725 ppm) and a relative accuracy of 6.7% when compared with CEMS for whole journeys and varying load situations. Further improvements on the performance could be obtained by updating this function. The calculated yearly emission for a total engine running time of 4618 h was 316 t NO x ± 38 t and the average NO x emission corrected for ambient conditions 14.3 g kWh corr -1 . The exhaust profile of the engine in terms of NO x , CO and CO 2 emissions as determined by CEMS was similar for most of the year. Towards the end of the study period, a significantly lower NO x emission was detected which was probably caused by replacement of fuel injector nozzles. The study suggests that PEMS can be a viable option for continuous, long-term NO x measurements on board ships. (author)

  14. Corporate sponsored education initiatives on board the ISS

    Science.gov (United States)

    Durham, Ian T.; Durham, Alyson S.; Pawelczyk, James A.; Brod, Lawrence B.; Durham, Thomas F.

    1999-01-01

    This paper proposes the creation of a corporate sponsored ``Lecture from Space'' program on board the International Space Station (ISS) with funding coming from a host of new technology and marketing spin-offs. This program would meld existing education initiatives in NASA with new corporate marketing techniques. Astronauts in residence on board the ISS would conduct short ten to fifteen minute live presentations and/or conduct interactive discussions carried out by a teacher in the classroom. This concept is similar to a program already carried out during the Neurolab mission on Shuttle flight STS-90. Building on that concept, the interactive simulcasts would be broadcast over the Internet and linked directly to computers and televisions in classrooms worldwide. In addition to the live broadcasts, educational programs and demonstrations can be recorded in space, and marketed and sold for inclusion in television programs, computer software, and other forms of media. Programs can be distributed directly into classrooms as an additional presentation supplement, as well as over the Internet or through cable and broadcast television, similar to the Canadian Discovery Channel's broadcasts of the Neurolab mission. Successful marketing and advertisement can eventually lead to the creation of an entirely new, privately run cottage industry involving the distribution and sale of educationally related material associated with the ISS that would have the potential to become truly global in scope. By targeting areas of expertise and research interest in microgravity, a large curriculum could be developed using space exploration as a unifying theme. Expansion of this concept could enhance objectives already initiated through the International Space University to include elementary and secondary school students. The ultimate goal would be to stimulate interest in space and space related sciences in today's youth through creative educational marketing initiatives while at the

  15. Automated business process management – in times of digital transformation using machine learning or artificial intelligence

    OpenAIRE

    Paschek Daniel; Luminosu Caius Tudor; Draghici Anca

    2017-01-01

    The continuous optimization of business processes is still a challenge for companies. In times of digital transformation, faster changing internal and external framework conditions and new customer expectations for fastest delivery and best quality of goods and many more, companies should set up their internal process at the best way. But what to do if framework conditions changed unexpectedly? The purpose of the paper is to analyse how the digital transformation will impact the Business Proc...

  16. The prediction of breast cancer biopsy outcomes using two CAD approaches that both emphasize an intelligible decision process

    International Nuclear Information System (INIS)

    Elter, M.; Schulz-Wendtland, R.; Wittenberg, T.

    2007-01-01

    Mammography is the most effective method for breast cancer screening available today. However, the low positive predictive value of breast biopsy resulting from mammogram interpretation leads to approximately 70% unnecessary biopsies with benign outcomes. To reduce the high number of unnecessary breast biopsies, several computer-aided diagnosis (CAD) systems have been proposed in the last several years. These systems help physicians in their decision to perform a breast biopsy on a suspicious lesion seen in a mammogram or to perform a short term follow-up examination instead. We present two novel CAD approaches that both emphasize an intelligible decision process to predict breast biopsy outcomes from BI-RADS findings. An intelligible reasoning process is an important requirement for the acceptance of CAD systems by physicians. The first approach induces a global model based on decison-tree learning. The second approach is based on case-based reasoning and applies an entropic similarity measure. We have evaluated the performance of both CAD approaches on two large publicly available mammography reference databases using receiver operating characteristic (ROC) analysis, bootstrap sampling, and the ANOVA statistical significance test. Both approaches outperform the diagnosis decisions of the physicians. Hence, both systems have the potential to reduce the number of unnecessary breast biopsies in clinical practice. A comparison of the performance of the proposed decision tree and CBR approaches with a state of the art approach based on artificial neural networks (ANN) shows that the CBR approach performs slightly better than the ANN approach, which in turn results in slightly better performance than the decision-tree approach. The differences are statistically significant (p value <0.001). On 2100 masses extracted from the DDSM database, the CRB approach for example resulted in an area under the ROC curve of A(z)=0.89±0.01, the decision-tree approach in A(z)=0.87±0

  17. How holistic processing of faces relates to cognitive control and intelligence.

    Science.gov (United States)

    Gauthier, Isabel; Chua, Kao-Wei; Richler, Jennifer J

    2018-04-16

    The Vanderbilt Holistic Processing Test for faces (VHPT-F) is the first standard test designed to measure individual differences in holistic processing. The test measures failures of selective attention to face parts through congruency effects, an operational definition of holistic processing. However, this conception of holistic processing has been challenged by the suggestion that it may tap into the same selective attention or cognitive control mechanisms that yield congruency effects in Stroop and Flanker paradigms. Here, we report data from 130 subjects on the VHPT-F, several versions of Stroop and Flanker tasks, as well as fluid IQ. Results suggested a small degree of shared variance in Stroop and Flanker congruency effects, which did not relate to congruency effects on the VHPT-F. Variability on the VHPT-F was also not correlated with Fluid IQ. In sum, we find no evidence that holistic face processing as measured by congruency in the VHPT-F is accounted for by domain-general control mechanisms.

  18. An Introduction to Intelligent Processing Programs Developed by the Air Force Manufacturing Technology Directorate

    Science.gov (United States)

    Sampson, Paul G.; Sny, Linda C.

    1992-01-01

    The Air Force has numerous on-going manufacturing and integration development programs (machine tools, composites, metals, assembly, and electronics) which are instrumental in improving productivity in the aerospace industry, but more importantly, have identified strategies and technologies required for the integration of advanced processing equipment. An introduction to four current Air Force Manufacturing Technology Directorate (ManTech) manufacturing areas is provided. Research is being carried out in the following areas: (1) machining initiatives for aerospace subcontractors which provide for advanced technology and innovative manufacturing strategies to increase the capabilities of small shops; (2) innovative approaches to advance machine tool products and manufacturing processes; (3) innovative approaches to advance sensors for process control in machine tools; and (4) efforts currently underway to develop, with the support of industry, the Next Generation Workstation/Machine Controller (Low-End Controller Task).

  19. Introduction of artificial intelligence techniques for computerized management of defects in an industrial process

    International Nuclear Information System (INIS)

    Utzel, N.

    1991-06-01

    An optimized management of Tore Supra Tokamak requires a computerized defect management. The aim is the analysis of an inhibited situation not corrected by automatisms of the process and that can be handled only by human intervention. The operator should understand, make a diagnosis and act to restore the system. In this report are studied an expert system helping the operator to analyze defects of the two main cooling loops (decarbonated water and pressurized water), management of the history of malfunction and recording of diagnosises, elaboration of an adapted expert model and installation of a methodology for defect management in other processes of Tore Supra [fr

  20. Pathogen intelligence

    Directory of Open Access Journals (Sweden)

    Michael eSteinert

    2014-01-01

    Full Text Available Different species inhabit different sensory worlds and thus have evolved diverse means of processing information, learning and memory. In the escalated arms race with host defense, each pathogenic bacterium not only has evolved its individual cellular sensing and behaviour, but also collective sensing, interbacterial communication, distributed information processing, joint decision making, dissociative behaviour, and the phenotypic and genotypic heterogeneity necessary for epidemiologic success. Moreover, pathogenic populations take advantage of dormancy strategies and rapid evolutionary speed, which allow them to save co-generated intelligent traits in a collective genomic memory. This review discusses how these mechanisms add further levels of complexity to bacterial pathogenicity and transmission, and how mining for these mechanisms could help to develop new anti-infective strategies.

  1. Intelligent Modeling Combining Adaptive Neuro Fuzzy Inference System and Genetic Algorithm for Optimizing Welding Process Parameters

    Science.gov (United States)

    Gowtham, K. N.; Vasudevan, M.; Maduraimuthu, V.; Jayakumar, T.

    2011-04-01

    Modified 9Cr-1Mo ferritic steel is used as a structural material for steam generator components of power plants. Generally, tungsten inert gas (TIG) welding is preferred for welding of these steels in which the depth of penetration achievable during autogenous welding is limited. Therefore, activated flux TIG (A-TIG) welding, a novel welding technique, has been developed in-house to increase the depth of penetration. In modified 9Cr-1Mo steel joints produced by the A-TIG welding process, weld bead width, depth of penetration, and heat-affected zone (HAZ) width play an important role in determining the mechanical properties as well as the performance of the weld joints during service. To obtain the desired weld bead geometry and HAZ width, it becomes important to set the welding process parameters. In this work, adaptative neuro fuzzy inference system is used to develop independent models correlating the welding process parameters like current, voltage, and torch speed with weld bead shape parameters like depth of penetration, bead width, and HAZ width. Then a genetic algorithm is employed to determine the optimum A-TIG welding process parameters to obtain the desired weld bead shape parameters and HAZ width.

  2. Intelligence Ethics:

    DEFF Research Database (Denmark)

    Rønn, Kira Vrist

    2016-01-01

    Questions concerning what constitutes a morally justified conduct of intelligence activities have received increased attention in recent decades. However, intelligence ethics is not yet homogeneous or embedded as a solid research field. The aim of this article is to sketch the state of the art...... of intelligence ethics and point out subjects for further scrutiny in future research. The review clusters the literature on intelligence ethics into two groups: respectively, contributions on external topics (i.e., the accountability of and the public trust in intelligence agencies) and internal topics (i.......e., the search for an ideal ethical framework for intelligence actions). The article concludes that there are many holes to fill for future studies on intelligence ethics both in external and internal discussions. Thus, the article is an invitation – especially, to moral philosophers and political theorists...

  3. 10th International Symposium on Intelligent Distributed Computing

    CERN Document Server

    Seghrouchni, Amal; Beynier, Aurélie; Camacho, David; Herpson, Cédric; Hindriks, Koen; Novais, Paulo

    2017-01-01

    This book presents the combined peer-reviewed proceedings of the tenth International Symposium on Intelligent Distributed Computing (IDC’2016), which was held in Paris, France from October 10th to 12th, 2016. The 23 contributions address a range of topics related to theory and application of intelligent distributed computing, including: Intelligent Distributed Agent-Based Systems, Ambient Intelligence and Social Networks, Computational Sustainability, Intelligent Distributed Knowledge Representation and Processing, Smart Networks, Networked Intelligence and Intelligent Distributed Applications, amongst others.

  4. Logic Programs as a Specification and Description Tool in the Design Process of an Intelligent Tutoring System

    OpenAIRE

    Möbus, Claus

    1987-01-01

    We propose the use of logic programs when designing intelligent tutoring systems. With their help we specified the small-step semantics of the learning curriculum, designed the graphical user interface, derived instructions and modelled students' knowledge.

  5. Ultrasonic velocity measurements- a potential sensor for intelligent processing of austenitic stainless steels

    International Nuclear Information System (INIS)

    Venkadesan, S.; Palanichamy, P.; Vasudevan, M.; Baldev Raj

    1996-01-01

    Development of sensors based on Non-Destructive Evaluation (NDE) techniques for on-line sensing of microstructure and properties requires a thorough knowledge on the relation between the sensing mechanism/measurement of an NDE technique and the microstructure. As a first step towards developing an on-line sensor for studying the dynamic microstructural changes during processing of austenitic stainless steels, ultrasonic velocity measurements have been carried out to study the microstructural changes after processing. Velocity measurements could follow the progress of annealing starting from recovery, onset and completion of recrystallization, sense the differences in the microstructure obtained after hot deformation and estimate the grain size. This paper brings out the relation between the sensing method based on ultrasonic velocity measurements and the microstructure in austenitic stainless steel. (author)

  6. Semantic Business Intelligence - a New Generation of Business Intelligence

    Directory of Open Access Journals (Sweden)

    Dinu AIRINEI

    2012-01-01

    Full Text Available Business Intelligence Solutions represents applications used by companies to manage process and analyze data to provide substantiated decision. In the context of Semantic Web develop-ment trend is to integrate semantic unstructured data, making business intelligence solutions to be redesigned in such a manner that can analyze, process and synthesize, in addition to traditional data and data integrated with semantic another form and structure. This invariably leads appearance of new BI solution, called Semantic Business Intelligence.

  7. On-line Cutting Tool Condition Monitoring in Machining Processes Using Artificial Intelligence

    OpenAIRE

    Vallejo, Antonio J.; Morales-Menéndez, Rub&#;n; Alique, J.R.

    2008-01-01

    This chapter presented new ideas for monitoring and diagnosis of the cutting tool condition with two different algorithms for pattern recognition: HMM, and ANN. The monitoring and diagnosis system was implemented for peripheral milling process in HSM, where several Aluminium alloys and cutting tools were used. The flank wear (VB) was selected as the criterion to evaluate the tool's life and four cutting tool conditions were defined to be recognized: New, half new, half worn, and worn conditio...

  8. Investment Cost Model in Business Process Intelligence in Banking And Electricity Company

    Directory of Open Access Journals (Sweden)

    Arta Moro Sundjaja

    2016-06-01

    Full Text Available Higher demand from the top management in measuring business process performance causes the incremental implementation of BPM and BI in the enterprise. The problem faced by top managements is how to integrate their data from all system used to support the business and process the data become information that able to support the decision-making processes. Our literature review elaborates several implementations of BPI on companies in Australia and Germany, challenges faced by organizations in developing BPI solution in their organizations and some cost model to calculate the investment of BPI solutions. This paper shows the success in BPI application of banks and assurance companies in German and electricity work in Australia aims to give a vision about the importance of BPI application. Many challenges in BPI application of companies in German and Australia, BPI solution, and data warehouse design development have been discussed to add insight in future BPI development. And the last is an explanation about how to analyze cost associated with BPI solution investment.

  9. ON-BOARD MONITORING OF TECHNICAL STATE FOR POWER UNITS OF WHEELED AND TRACKED VEHICLES

    Directory of Open Access Journals (Sweden)

    Yu. D. Karpievich

    2016-01-01

    Full Text Available The paper considers new methodologies pertaining to on-board diagnosis of wear-out rate for friction linings of a clutch driven disk and friction discs of a hydraulic press clutch of transmission gear boxes which are based on physical process that uses friction work as an integrated indicator. A new methodology in determination of life-span rate for engine oil has been developed in the paper. The paper presents block schematic diagrams for on-board monitoring of technical state for power units of wheeled and tracked vehicles. Usage of friction work as an integrated indicator for determination of wear-out rate for friction linings of clutch driven disk and friction discs of a haydraulic press clutch makes it possible timely at any operational period of wheeled and tracked vehicles to determine their residual operation life and forecast their replacement.While taking volume of the used fuel for determination of engine oil life-span rate it permits quickly and effectively at any operational period of wheeled and tracked vehicles to determine residual useful life of the engine oil and also forecast its replacement.

  10. Intelligence Naturelle et Intelligence Artificielle

    OpenAIRE

    Dubois, Daniel

    2011-01-01

    Cet article présente une approche systémique du concept d’intelligence naturelle en ayant pour objectif de créer une intelligence artificielle. Ainsi, l’intelligence naturelle, humaine et animale non-humaine, est une fonction composée de facultés permettant de connaître et de comprendre. De plus, l'intelligence naturelle reste indissociable de la structure, à savoir les organes du cerveau et du corps. La tentation est grande de doter les systèmes informatiques d’une intelligence artificielle ...

  11. Artificial Intelligence In Processing A Sequence Of Time-Varying Images

    Science.gov (United States)

    Siler, W.; Tucker, D.; Buckley, J.; Hess, R. G.; Powell, V. G.

    1985-04-01

    A computer system is described for unsupervised analysis of five sets of ultrasound images of the heart. Each set consists of 24 frames taken at 33 millisecond intervals. The images are acquired in real time with computer control of the ultrasound apparatus. After acquisition the images are segmented by a sequence of image-processing programs; features are extracted and stored in a version of the Carnegie- Mellon Blackboard. Region classification is accomplished by a fuzzy logic expert system FLOPS based on OPS5. Preliminary results are given.

  12. Intelligent environmental sensing

    CERN Document Server

    Mukhopadhyay, Subhas

    2015-01-01

    Developing environmental sensing and monitoring technologies become essential especially for industries that may cause severe contamination. Intelligent environmental sensing uses novel sensor techniques, intelligent signal and data processing algorithms, and wireless sensor networks to enhance environmental sensing and monitoring. It finds applications in many environmental problems such as oil and gas, water quality, and agriculture. This book addresses issues related to three main approaches to intelligent environmental sensing and discusses their latest technological developments. Key contents of the book include:   Agricultural monitoring Classification, detection, and estimation Data fusion Geological monitoring Motor monitoring Multi-sensor systems Oil reservoirs monitoring Sensor motes Water quality monitoring Wireless sensor network protocol  

  13. Longitudinal Mediation of Processing Speed on Age-Related Change in Memory and Fluid Intelligence

    Science.gov (United States)

    Robitaille, Annie; Piccinin, Andrea M.; Muniz, Graciela; Hoffman, Lesa; Johansson, Boo; Deeg, Dorly J.H.; Aartsen, Marja J.; Comijs, Hannie C.; Hofer, Scott M.

    2014-01-01

    Age-related decline in processing speed has long been considered a key driver of cognitive aging. While the majority of empirical evidence for the processing speed hypothesis has been obtained from analyses of between-person age differences, longitudinal studies provide a direct test of within-person change. Using recent developments in longitudinal mediation analysis, we examine the speed–mediation hypothesis at both the within- and between-person levels in two longitudinal studies, LASA and OCTO-Twin. We found significant within-person indirect effects of change in age, such that increasing age was related to lower speed which, in turn, relates to lower performance across repeated measures on other cognitive outcomes. Although between-person indirect effects were also significant in LASA, they were not in OCTO-Twin. These differing magnitudes of direct and indirect effects across levels demonstrate the importance of separating between- and within-person effects in evaluating theoretical models of age-related change. PMID:23957224

  14. Fiber optical sensing on-board communication satellites

    Science.gov (United States)

    Hurni, A.; Lemke, N. M. K.; Roner, M.; Obermaier, J.; Putzer, P.; Kuhenuri Chami, N.

    2017-11-01

    Striving constantly to reduce mass, AIT effort and overall cost of the classical point-to-point wired temperature sensor harness on-board telecommunication satellites, OHB System (formerly Kayser-Threde) has introduced the Hybrid Sensor Bus (HSB) system. As a future spacecraft platform element, HSB relies on electrical remote sensor units as well as fiber-optical sensors, both of which can serially be connected in a bus architecture. HSB is a modular measurement system with many applications, also thanks to the opportunities posed by the digital I²C bus. The emphasis, however, is on the introduction of fiber optics and especially fiber-Bragg grating (FBG) temperature sensors as disruptive innovation for the company's satellite platforms. The light weight FBG sensors are directly inscribed in mechanically robust and radiation tolerant fibers, reducing the need for optical fiber connectors and splices to a minimum. Wherever an FBG sensor shall be used, the fiber is glued together with a corresponding temperature transducer to the satellites structure or to a subsystem. The transducer is necessary to provide decoupling of mechanical stress, but simultaneously ensure a high thermal conductivity. HSB has been developed in the frame of an ESA-ARTES program with European and German co-funding and will be verified as flight demonstrator on-board the German Heinrich Hertz satellite (H2Sat). In this paper the Engineering Model development of HSB is presented and a Fiber-optical Sensor Multiplexer for a more flexible sensor bus architecture is introduced. The HSB system aims at telecommunication satellite platforms with an operational life time beyond 15 years in geostationary orbit. It claims a high compatibility in terms of performance and interfaces with existing platforms while it was designed with future applications with increased radiation exposure already in mind. In its basic configuration HSB consists of four modules which are the Power Supply Unit, the HSB

  15. The Professionalization of Intelligence Cooperation

    DEFF Research Database (Denmark)

    Svendsen, Adam David Morgan

    "Providing an in-depth insight into the subject of intelligence cooperation (officially known as liason), this book explores the complexities of this process. Towards facilitating a general understanding of the professionalization of intelligence cooperation, Svendsen's analysis includes risk...... management and encourages the realisation of greater resilience. Svendsen discusses the controversial, mixed and uneven characterisations of the process of the professionalization of intelligence cooperation and argues for a degree of 'fashioning method out of mayhem' through greater operational...

  16. Intelligent tuning of vibration mitigation process for single link manipulator using fuzzy logic

    Directory of Open Access Journals (Sweden)

    Ahmed A. Ali

    2017-08-01

    Full Text Available In this work, active vibration mitigation for smart single link manipulator is presented. Two piezoelectric transducers were utilized to act as actuator and sensor respectively. Classical Proportional (P controller was tested numerically and experimentally. The comparison between measured results showed good agreement. The proposed work includes the introducing of fuzzy logic for tuning controller's gain within finite element method. Classical Proportional-Integral (PI, Fuzzy-P and Fuzzy-PI controllers were totally integrated as a series of [IF-Then] states and solved numerically by using Finite Element (FE solver (ANSYS. Proposed method will pave the way on solving the tuning process totally within single FE solver with high efficiency. Proposed method satisfied mitigation in the overall free response with about 52% and 74% of the manipulator settling time when Fuzzy-P and Fuzzy-PI controllers were activated respectively. This contribution can be utilized for many other applications related to fuzzy topics.

  17. An intelligent approach to optimize the EDM process parameters using utility concept and QPSO algorithm

    Directory of Open Access Journals (Sweden)

    Chinmaya P. Mohanty

    2017-04-01

    Full Text Available Although significant research has gone into the field of electrical discharge machining (EDM, analysis related to the machining efficiency of the process with different electrodes has not been adequately made. Copper and brass are frequently used as electrode materials but graphite can be used as a potential electrode material due to its high melting point temperature and good electrical conductivity. In view of this, the present work attempts to compare the machinability of copper, graphite and brass electrodes while machining Inconel 718 super alloy. Taguchi’s L27 orthogonal array has been employed to collect data for the study and analyze effect of machining parameters on performance measures. The important performance measures selected for this study are material removal rate, tool wear rate, surface roughness and radial overcut. Machining parameters considered for analysis are open circuit voltage, discharge current, pulse-on-time, duty factor, flushing pressure and electrode material. From the experimental analysis, it is observed that electrode material, discharge current and pulse-on-time are the important parameters for all the performance measures. Utility concept has been implemented to transform a multiple performance characteristics into an equivalent performance characteristic. Non-linear regression analysis is carried out to develop a model relating process parameters and overall utility index. Finally, the quantum behaved particle swarm optimization (QPSO and particle swarm optimization (PSO algorithms have been used to compare the optimal level of cutting parameters. Results demonstrate the elegance of QPSO in terms of convergence and computational effort. The optimal parametric setting obtained through both the approaches is validated by conducting confirmation experiments.

  18. How semantics can inform the geological mapping process and support intelligent queries

    Science.gov (United States)

    Lombardo, Vincenzo; Piana, Fabrizio; Mimmo, Dario

    2017-04-01

    The geologic mapping process requires the organization of data according to the general knowledge about the objects, namely the geologic units, and to the objectives of a graphic representation of such objects in a map, following an established model of geotectonic evolution. Semantics can greatly help such a process in two concerns: the provision of a terminological base to name and classify the objects of the map; on the other, the implementation of a machine-readable encoding of the geologic knowledge base supports the application of reasoning mechanisms and the derivation of novel properties and relations about the objects of the map. The OntoGeonous initiative has built a terminological base of geological knowledge in a machine-readable format, following the Semantic Web tenets and the Linked Data paradigm. The major knowledge sources of the OntoGeonous initiative are GeoScience Markup Language schemata and vocabularies (through its last version, GeoSciML 4, 2015, published by the IUGS CGI Commission) and the INSPIRE "Data Specification on Geology" directives (an operative simplification of GeoSciML, published by INSPIRE Thematic Working Group Geology of the European Commission). The Linked Data paradigm has been exploited by linking (without replicating, to avoid inconsistencies) the already existing machine-readable encoding for some specific domains, such as the lithology domain (vocabulary Simple Lithology) and the geochronologic time scale (ontology "gts"). Finally, for the upper level knowledge, shared across several geologic domains, we have resorted to NASA SWEET ontology. The OntoGeonous initiative has also produced a wiki that explains how the geologic knowledge has been encoded from shared geoscience vocabularies (https://www.di.unito.it/wikigeo/). In particular, the sections dedicated to axiomatization will support the construction of an appropriate data base schema that can be then filled with the objects of the map. This contribution will discuss

  19. Innovative on board payload optical architecture for high throughput satellites

    Science.gov (United States)

    Baudet, D.; Braux, B.; Prieur, O.; Hughes, R.; Wilkinson, M.; Latunde-Dada, K.; Jahns, J.; Lohmann, U.; Fey, D.; Karafolas, N.

    2017-11-01

    For the next generation of HighThroughPut (HTP) Telecommunications Satellites, space end users' needs will result in higher link speeds and an increase in the number of channels; up to 512 channels running at 10Gbits/s. By keeping electrical interconnections based on copper, the constraints in term of power dissipation, number of electrical wires and signal integrity will become too demanding. The replacement of the electrical links by optical links is the most adapted solution as it provides high speed links with low power consumption and no EMC/EMI. But replacing all electrical links by optical links of an On Board Payload (OBP) is challenging. It is not simply a matter of replacing electrical components with optical but rather the whole concept and architecture have to be rethought to achieve a high reliability and high performance optical solution. In this context, this paper will present the concept of an Innovative OBP Optical Architecture. The optical architecture was defined to meet the critical requirements of the application: signal speed, number of channels, space reliability, power dissipation, optical signals crossing and components availability. The resulting architecture is challenging and the need for new developments is highlighted. But this innovative optically interconnected architecture will substantially outperform standard electrical ones.

  20. Fuel saving performances of marine diesel engine oils on board

    Energy Technology Data Exchange (ETDEWEB)

    Hirose, Yasunori; Henmi, Takashi; Minamitani, Hiromu; Akizawa, Hayao; Hamada, Minoru; Ashida, Jiro

    1988-05-01

    After the second oil crisis, the percentage of the fuel cost against the operational cost of a ship has been showing the rising tendency, engine manufacturers have placed the top priority on the improvement of fuel consumption, operators have been conducting various energy saving measures and refiners have been paying efforts to improve lubricating oil. This article reports the study on the lubricating oil characteristics affecting the fuel consumption per power output, particularly the viscosity and the adding effect of friction modifier additives by using dynamo-generator diesel engines on board the ships already in commission. The investigation was conducted by comparing the cases of using several sample oils with the cases of using the reference oils. According to the results, the viscous property of engine oil was most effective on fuel consumption and the lower the viscosity of oil, the more the fuel consumption effect was. However, the addition of friction modifier additives did hardly show any improvement of the above effect. (5 figs, 4 tabs, 3 refs)

  1. Intelligent Machine Vision Based Modeling and Positioning System in Sand Casting Process

    Directory of Open Access Journals (Sweden)

    Shahid Ikramullah Butt

    2017-01-01

    Full Text Available Advanced vision solutions enable manufacturers in the technology sector to reconcile both competitive and regulatory concerns and address the need for immaculate fault detection and quality assurance. The modern manufacturing has completely shifted from the manual inspections to the machine assisted vision inspection methodology. Furthermore, the research outcomes in industrial automation have revolutionized the whole product development strategy. The purpose of this research paper is to introduce a new scheme of automation in the sand casting process by means of machine vision based technology for mold positioning. Automation has been achieved by developing a novel system in which casting molds of different sizes, having different pouring cup location and radius, position themselves in front of the induction furnace such that the center of pouring cup comes directly beneath the pouring point of furnace. The coordinates of the center of pouring cup are found by using computer vision algorithms. The output is then transferred to a microcontroller which controls the alignment mechanism on which the mold is placed at the optimum location.

  2. Developing a Business Intelligence Process for a Training Module in SharePoint 2010

    Science.gov (United States)

    Schmidtchen, Bryce; Solano, Wanda M.; Albasini, Colby

    2015-01-01

    Prior to this project, training information for the employees of the National Center for Critical Processing and Storage (NCCIPS) was stored in an array of unrelated spreadsheets and SharePoint lists that had to be manually updated. By developing a content management system through a web application platform named SharePoint, this training system is now highly automated and provides a much less intensive method of storing training data and scheduling training courses. This system was developed by using SharePoint Designer and laying out the data structure for the interaction between different lists of data about the employees. The automation of data population inside of the lists was accomplished by implementing SharePoint workflows which essentially lay out the logic for how data is connected and calculated between certain lists. The resulting training system is constructed from a combination of five lists of data with a single list acting as the user-friendly interface. This interface is populated with the courses required for each employee and includes past and future information about course requirements. The employees of NCCIPS now have the ability to view, log, and schedule their training information and courses with much more ease. This system will relieve a significant amount of manual input and serve as a powerful informational resource for the employees of NCCIPS in the future.

  3. Fetal QRS extraction from abdominal recordings via model-based signal processing and intelligent signal merging

    International Nuclear Information System (INIS)

    Haghpanahi, Masoumeh; Borkholder, David A

    2014-01-01

    Noninvasive fetal ECG (fECG) monitoring has potential applications in diagnosing congenital heart diseases in a timely manner and assisting clinicians to make more appropriate decisions during labor. However, despite advances in signal processing and machine learning techniques, the analysis of fECG signals has still remained in its preliminary stages. In this work, we describe an algorithm to automatically locate QRS complexes in noninvasive fECG signals obtained from a set of four electrodes placed on the mother’s abdomen. The algorithm is based on an iterative decomposition of the maternal and fetal subspaces and filtering of the maternal ECG (mECG) components from the fECG recordings. Once the maternal components are removed, a novel merging technique is applied to merge the signals and detect the fetal QRS (fQRS) complexes. The algorithm was trained and tested on the fECG datasets provided by the PhysioNet/CinC challenge 2013. The final results indicate that the algorithm is able to detect fetal peaks for a variety of signals with different morphologies and strength levels encountered in clinical practice. (paper)

  4. Designing a framework of intelligent information processing for dentistry administration data.

    Science.gov (United States)

    Amiri, N; Matthews, D C; Gao, Q

    2005-07-01

    This study was designed to test a cumulative view of current data in the clinical database at the Faculty of Dentistry, Dalhousie University. We planned to examine associations among demographic factors and treatments. Three tables were selected from the database of the faculty: patient, treatment and procedures. All fields and record numbers in each table were documented. Data was explored using SQL server and Visual Basic and then cleaned by removing incongruent fields. After transformation, a data warehouse was created. This was imported to SQL analysis services manager to create an OLAP (Online Analytic Process) cube. The multidimensional model used for access to data was created using a star schema. Treatment count was the measurement variable. Five dimensions--date, postal code, gender, age group and treatment categories--were used to detect associations. Another data warehouse of 8 tables (international tooth code # 1-8) was created and imported to SAS enterprise miner to complete data mining. Association nodes were used for each table to find sequential associations and minimum criteria were set to 2% of cases. Findings of this study confirmed most assumptions of treatment planning procedures. There were some small unexpected patterns of clinical interest. Further developments are recommended to create predictive models. Recent improvements in information technology offer numerous advantages for conversion of raw data from faculty databases to information and subsequently to knowledge. This knowledge can be used by decision makers, managers, and researchers to answer clinical questions, affect policy change and determine future research needs.

  5. Use of Information Intelligent Components for the Analysis of Complex Processes of Marine Energy Systems

    Directory of Open Access Journals (Sweden)

    Chernyi Sergei

    2016-09-01

    Full Text Available Synchronous motors and their modifications (ac converter-fed motor, etc. enable to develop low-noise, reliable and economically efficient electric drive systems. The construction of up-to-date systems based on the synchronous machines is impossible without development of the computing software incorporating mathematical and computing simulation. In its turn, modelling of the synchronous machines as a rule is based on the equations by Park-Gorev, application of which requires adoption of a series of allowances. These allowances in a number of cases do not permit to obtain adequate results of the simulation coinciding with the results of field experiments of the systems under review. Moreover, while applying the system of equations by Park-Gorev to research the systems including interaction of synchronous machines with semiconducting converters of electric energy it is necessary simulate the process of formation their controlling signals in the sphere of frequency. If the states of converter’s keys are defined not only by controlling impulses but also by the state of currents in the synchronous machines flowing through them, such approach is not reasonable.

  6. Advertising and algorithms – the obvious gains and hidden losses of using software with intelligent agent capabilities in the creative process of art directors and copywriters

    OpenAIRE

    Barker, Richie

    2017-01-01

    Situated at the intersection of information technology, advertising and creativity theory, this thesis presents a detailed picture of the influence of autonomous software applications on the creative process of advertising art directors and copywriters. These applications, which are known in the field of information technology as ‘intelligent agents,’ commonly possess the ability to learn from the user and autonomously pursue their own goals. The search engine Google, which employs intelligen...

  7. Artificial intelligence in cardiology

    OpenAIRE

    Bonderman, Diana

    2017-01-01

    Summary Decision-making is complex in modern medicine and should ideally be based on available data, structured knowledge and proper interpretation in the context of an individual patient. Automated algorithms, also termed artificial intelligence that are able to extract meaningful patterns from data collections and build decisions upon identified patterns may be useful assistants in clinical decision-making processes. In this article, artificial intelligence-based studies in clinical cardiol...

  8. Flow chemistry: intelligent processing of gas-liquid transformations using a tube-in-tube reactor.

    Science.gov (United States)

    Brzozowski, Martin; O'Brien, Matthew; Ley, Steven V; Polyzos, Anastasios

    2015-02-17

    reactive gas in a given reaction mixture. We have developed a tube-in-tube reactor device consisting of a pair of concentric capillaries in which pressurized gas permeates through an inner Teflon AF-2400 tube and reacts with dissolved substrate within a liquid phase that flows within a second gas impermeable tube. This Account examines our efforts toward the development of a simple, unified methodology for the processing of gaseous reagents in flow by way of development of a tube-in-tube reactor device and applications to key C-C, C-N, and C-O bond forming and hydrogenation reactions. We further describe the application to multistep reactions using solid-supported reagents and extend the technology to processes utilizing multiple gas reagents. A key feature of our work is the development of computer-aided imaging techniques to allow automated in-line monitoring of gas concentration and stoichiometry in real time. We anticipate that this Account will illustrate the convenience and benefits of membrane tube-in-tube reactor technology to improve and concomitantly broaden the scope of gas/liquid/solid reactions in organic synthesis.

  9. Intelligence and treaty ratification

    International Nuclear Information System (INIS)

    Sojka, G.L.

    1990-01-01

    What did the intelligence community and the Intelligence Committee di poorly in regard to the treaty ratification process for arms control? We failed to solve the compartmentalization problem/ This is a second-order problem, and, in general, analysts try to be very open; but there are problems nevertheless. There are very few, if any, people within the intelligence community who are cleared for everything relevant to our monitoring capability emdash short of probably the Director of Central Intelligence and the president emdash and this is a major problem. The formal monitoring estimates are drawn up by individuals who do not have access to all the information to make the monitoring judgements. This paper reports that the intelligence community did not present a formal document on either Soviet incentives of disincentives to cheat or on the possibility of cheating scenarios, and that was a mistake. However, the intelligence community was very responsive in producing those types of estimates, and, ultimately, the evidence behind them in response to questions. Nevertheless, the author thinks the intelligence community would do well to address this issue up front before a treaty is submitted to the Senate for advice and consent

  10. Possibilities of reduction of the on-board energy for an innovative subway

    OpenAIRE

    Allègre, A-L.; Barrade, P.; Delarue, P.; Bouscayrol, A.; Chattot, E.; El-Fassi, S.

    2009-01-01

    An innovative subway has been proposed using supercapacitors as energy source. In this paper, are presented different possibilities to reduce on-board stored energy in order to downsize the on-board energy storage subsystem. Special attention is paid to the influence of a feeding rail extension or a downward slope at the beginning of the interstation on the on-board stored energy. A map is built to facilitate the selection of the solution which leads to reduce the on-board energy.

  11. Assessment of emotion processing skills in acquired brain injury using an ability-based test of emotional intelligence.

    Science.gov (United States)

    Hall, Sarah E; Wrench, Joanne M; Wilson, Sarah J

    2018-04-01

    Social and emotional problems are commonly reported after moderate to severe acquired brain injury (ABI) and pose a significant barrier to rehabilitation. However, progress in assessment of emotional skills has been limited by a lack of validated measurement approaches. This study represents the first formal psychometric evaluation of the use of the Mayer-Salovey-Caruso Emotional Intelligence Test (MSCEIT) V2.0 as a tool for assessing skills in perceiving, using, understanding and managing emotions following ABI. The sample consisted of 82 participants aged 18-80 years in the postacute phase of recovery (2 months-7 years) after moderate to severe ABI. Participants completed the MSCEIT V2.0 and measures of cognition and mood. Sociodemographic and clinical variables were collated from participant interview and medical files. Results revealed deficits across all MSCEIT subscales (approximately 1 SD below the normative mean). Internal consistency was adequate at overall, area, and branch levels, and MSCEIT scores correlated in expected ways with key demographic, clinical, cognitive, and mood variables. MSCEIT performance was related to injury severity and clinician-rated functioning after ABI. Confirmatory factor analysis favored a 3-factor model of EI due to statistical redundancy of the Using Emotions branch. Overall, these findings suggest that the MSCEIT V2.0 is sensitive to emotion processing deficits after moderate to severe ABI, and can yield valid and reliable scores in an ABI sample. In terms of theoretical contributions, our findings support a domain-based, 3-factor approach for characterizing emotion-related abilities in brain-injured individuals. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

  12. Fatigue stress detection of VIRTIS cryocoolers on board Rosetta

    Science.gov (United States)

    Giuppi, Stefano; Politi, Romolo; Capria, Maria Teresa; Piccioni, Giuseppe; De Sanctis, Maria Cristina; Erard, Stéphane; Tosi, Federico; Capaccioni, Fabrizio; Filacchione, Gianrico

    Rosetta is a planetary cornerstone mission of the European Space Agency (ESA). It is devoted to the study of minor bodies of our solar system and it will be the first mission ever to land on a comet (the Jupiter-family comet 67P/Churyumov-Gerasimenko). VIRTIS-M is a sophisticated imaging spectrometer that combines two data channels in one compact instrument, respectively for the visible and the infrared range (0.25-5.0 μm). VIRTIS-H is devoted to infrared spectroscopy (2.5-5.0 μm) with high spectral resolution. Since the satellite will be inside the tail of the comet during one of the most important phases of the mission, it would not be appropriate to use a passive cooling system, due to the high flux of contaminants on the radiator. Therefore the IR sensors are cooled by two Stirling cycle cryocoolers produced by RICOR. Since RICOR operated life tests only on ground, it was decided to conduct an analysis on VIRTIS onboard Rosetta telemetries with the purpose of study possible differences in the cryocooler performancies. The analysis led to the conclusion that cryocoolers, when operating on board, are subject to a fatigue stress not present in the on ground life tests. The telemetries analysis shows a cyclic variation in cryocooler rotor angular velocity when -M or -H or both channel are operating (it has been also noted an influence of -M channel operations in -H cryocooler rotor angular velocity and vice versa) with frequencies mostly linked to operational parameters values. The frequencies have been calculated for each mission observation applying the Fast Fourier Transform (FFT). In order to evaluate possible hedge effects it has been also applied the Hanning window to compare the results. For a more complete evaluation of cryocoolers fatigue stress, for each mission observation the angular acceleration and the angular jerk have been calculated.

  13. Design of on-board Bluetooth wireless network system based on fault-tolerant technology

    Science.gov (United States)

    You, Zheng; Zhang, Xiangqi; Yu, Shijie; Tian, Hexiang

    2007-11-01

    In this paper, the Bluetooth wireless data transmission technology is applied in on-board computer system, to realize wireless data transmission between peripherals of the micro-satellite integrating electronic system, and in view of the high demand of reliability of a micro-satellite, a design of Bluetooth wireless network based on fault-tolerant technology is introduced. The reliability of two fault-tolerant systems is estimated firstly using Markov model, then the structural design of this fault-tolerant system is introduced; several protocols are established to make the system operate correctly, some related problems are listed and analyzed, with emphasis on Fault Auto-diagnosis System, Active-standby switch design and Data-Integrity process.

  14. Modelling intelligent behavior

    Science.gov (United States)

    Green, H. S.; Triffet, T.

    1993-01-01

    An introductory discussion of the related concepts of intelligence and consciousness suggests criteria to be met in the modeling of intelligence and the development of intelligent materials. Methods for the modeling of actual structure and activity of the animal cortex have been found, based on present knowledge of the ionic and cellular constitution of the nervous system. These have led to the development of a realistic neural network model, which has been used to study the formation of memory and the process of learning. An account is given of experiments with simple materials which exhibit almost all properties of biological synapses and suggest the possibility of a new type of computer architecture to implement an advanced type of artificial intelligence.

  15. Alzheimer's disease and intelligence.

    Science.gov (United States)

    Yeo, R A; Arden, R; Jung, R E

    2011-06-01

    A significant body of evidence has accumulated suggesting that individual variation in intellectual ability, whether assessed directly by intelligence tests or indirectly through proxy measures, is related to risk of developing Alzheimer's disease (AD) in later life. Important questions remain unanswered, however, such as the specificity of risk for AD vs. other forms of dementia, and the specific links between premorbid intelligence and development of the neuropathology characteristic of AD. Lower premorbid intelligence has also emerged as a risk factor for greater mortality across myriad health and mental health diagnoses. Genetic covariance contributes importantly to these associations, and pleiotropic genetic effects may impact diverse organ systems through similar processes, including inefficient design and oxidative stress. Through such processes, the genetic underpinnings of intelligence, specifically, mutation load, may also increase the risk of developing AD. We discuss how specific neurobiologic features of relatively lower premorbid intelligence, including reduced metabolic efficiency, may facilitate the development of AD neuropathology. The cognitive reserve hypothesis, the most widely accepted account of the intelligence-AD association, is reviewed in the context of this larger literature.

  16. Computer automation and artificial intelligence

    International Nuclear Information System (INIS)

    Hasnain, S.B.

    1992-01-01

    Rapid advances in computing, resulting from micro chip revolution has increased its application manifold particularly for computer automation. Yet the level of automation available, has limited its application to more complex and dynamic systems which require an intelligent computer control. In this paper a review of Artificial intelligence techniques used to augment automation is presented. The current sequential processing approach usually adopted in artificial intelligence has succeeded in emulating the symbolic processing part of intelligence, but the processing power required to get more elusive aspects of intelligence leads towards parallel processing. An overview of parallel processing with emphasis on transputer is also provided. A Fuzzy knowledge based controller for amination drug delivery in muscle relaxant anesthesia on transputer is described. 4 figs. (author)

  17. Introduction to the Special Issue on Intelligent and Cooperative Vehicles

    Directory of Open Access Journals (Sweden)

    Vicente Milanes

    2015-11-01

    Full Text Available Intelligent vehicles constitute one of the hot research topics on the Intelligent Transportation Systems (ITS field. The development of Advanced Driver Assistance Systems (ADAS based on multi-fusion information coming from on-board cameras, lidar or radar sensors is leading to more sophisticated passive and active safety systems. Additionally, the growing interest in using wireless communications to connect the vehicle either with other vehicles or the infrastructure is moving the intelligent vehicle research field toward smart interaction, moving to the Cooperative ITS (C-ITS research field. [...

  18. New technologies for supporting real-time on-board software development

    Science.gov (United States)

    Kerridge, D.

    1995-03-01

    The next generation of on-board data management systems will be significantly more complex than current designs, and will be required to perform more complex and demanding tasks in software. Improved hardware technology, in the form of the MA31750 radiation hard processor, is one key component in addressing the needs of future embedded systems. However, to complement these hardware advances, improved support for the design and implementation of real-time data management software is now needed. This will help to control the cost and risk assoicated with developing data management software development as it becomes an increasingly significant element within embedded systems. One particular problem with developing embedded software is managing the non-functional requirements in a systematic way. This paper identifies how Logica has exploited recent developments in hard real-time theory to address this problem through the use of new hard real-time analysis and design methods which can be supported by specialized tools. The first stage in transferring this technology from the research domain to industrial application has already been completed. The MA37150 Hard Real-Time Embedded Software Support Environment (HESSE) is a loosely integrated set of hardware and software tools which directly support the process of hard real-time analysis for software targeting the MA31750 processor. With further development, this HESSE promises to provide embedded system developers with software tools which can reduce the risks associated with developing complex hard real-time software. Supported in this way by more sophisticated software methods and tools, it is foreseen that MA31750 based embedded systems can meet the processing needs for the next generation of on-board data management systems.

  19. Intelligent Design

    DEFF Research Database (Denmark)

    Hjorth, Poul G.

    2005-01-01

    Forestillingen om at naturen er designet af en guddommelig 'intelligens' er et smukt filosofisk princip. Teorier om Intelligent Design som en naturvidenskabeligt baseret teori er derimod helt forfærdelig.......Forestillingen om at naturen er designet af en guddommelig 'intelligens' er et smukt filosofisk princip. Teorier om Intelligent Design som en naturvidenskabeligt baseret teori er derimod helt forfærdelig....

  20. Intelligent editor/printer enhancements

    Science.gov (United States)

    Woodfill, M. C.; Pheanis, D. C.

    1983-01-01

    Microprocessor support hardware, software, and cross assemblers relating to the Motorola 6800 and 6809 process systems were developed. Pinter controller and intelligent CRT development are discussed. The user's manual, design specifications for the MC6809 version of the intelligent printer controller card, and a 132-character by 64-line intelligent CRT display system using a Motorola 6809 MPU, and a one-line assembler and disassembler are provided.

  1. Intelligent Agent Appropriation in the Tracking Phase of an Environmental Scanning Process: A Case Study of a French Trade Union

    Science.gov (United States)

    Lafaye, Christophe

    2009-01-01

    Introduction: The rapid growth of the Internet has modified the boundaries of information acquisition (tracking) in environmental scanning. Despite the numerous advantages of this new medium, information overload is an enormous problem for Internet scanners. In order to help them, intelligent agents (i.e., autonomous, automated software agents…

  2. Exploring Possible Neural Mechanisms of Intelligence Differences Using Processing Speed and Working Memory Tasks: An fMRI Study

    Science.gov (United States)

    Waiter, Gordon D.; Deary, Ian J.; Staff, Roger T.; Murray, Alison D.; Fox, Helen C.; Starr, John M.; Whalley, Lawrence J.

    2009-01-01

    To explore the possible neural foundations of individual differences in intelligence test scores, we examined the associations between Raven's Matrices scores and two tasks that were administered in a functional magnetic resonance imaging (fMRI) setting. The two tasks were an n-back working memory (N = 37) task and inspection time (N = 47). The…

  3. 49 CFR 395.15 - Automatic on-board recording devices.

    Science.gov (United States)

    2010-10-01

    ... information concerning on-board system sensor failures and identification of edited data. Such support systems... driving today; (iv) Total hours on duty for the 7 consecutive day period, including today; (v) Total hours...-driver operation; (7) The on-board recording device/system identifies sensor failures and edited data...

  4. An overview of CAFE credits and incorporation of the benefits of on-board carbon capture.

    Science.gov (United States)

    2014-05-01

    This report discusses the application of Corporate Average Fuel Economy (CAFE) : credits that are currently available to vehicle manufacturers in the U.S., and the implications of : on-board carbon capture and sequestration (on-board CCS) on fu...

  5. Intelligent Extruder

    Energy Technology Data Exchange (ETDEWEB)

    AlperEker; Mark Giammattia; Paul Houpt; Aditya Kumar; Oscar Montero; Minesh Shah; Norberto Silvi; Timothy Cribbs

    2003-04-24

    ''Intelligent Extruder'' described in this report is a software system and associated support services for monitoring and control of compounding extruders to improve material quality, reduce waste and energy use, with minimal addition of new sensors or changes to the factory floor system components. Emphasis is on process improvements to the mixing, melting and de-volatilization of base resins, fillers, pigments, fire retardants and other additives in the :finishing'' stage of high value added engineering polymer materials. While GE Plastics materials were used for experimental studies throughout the program, the concepts and principles are broadly applicable to other manufacturers materials. The project involved a joint collaboration among GE Global Research, GE Industrial Systems and Coperion Werner & Pleiderer, USA, a major manufacturer of compounding equipment. Scope of the program included development of a algorithms for monitoring process material viscosity without rheological sensors or generating waste streams, a novel detection scheme for rapid detection of process upsets and an adaptive feedback control system to compensate for process upsets where at line adjustments are feasible. Software algorithms were implemented and tested on a laboratory scale extruder (50 lb/hr) at GE Global Research and data from a production scale system (2000 lb/hr) at GE Plastics was used to validate the monitoring and detection software. Although not evaluated experimentally, a new concept for extruder process monitoring through estimation of high frequency drive torque without strain gauges is developed and demonstrated in simulation. A plan to commercialize the software system is outlined, but commercialization has not been completed.

  6. Intelligent playgrounds

    DEFF Research Database (Denmark)

    Larsen, Lasse Juel

    2009-01-01

    This paper examines play, gaming and learning in regard to intelligent playware developed for outdoor use. The key questions are how does these novel artefacts influence the concept of play, gaming and learning. Up until now play and game have been understood as different activities. This paper...... examines if the sharp differentiation between the two can be uphold in regard to intelligent playware for outdoor use. Play and game activities will be analysed and viewed in conjunction with learning contexts. This paper will stipulate that intelligent playware facilitates rapid shifts in contexts...

  7. Artificial intelligence

    CERN Document Server

    Ennals, J R

    1987-01-01

    Artificial Intelligence: State of the Art Report is a two-part report consisting of the invited papers and the analysis. The editor first gives an introduction to the invited papers before presenting each paper and the analysis, and then concludes with the list of references related to the study. The invited papers explore the various aspects of artificial intelligence. The analysis part assesses the major advances in artificial intelligence and provides a balanced analysis of the state of the art in this field. The Bibliography compiles the most important published material on the subject of

  8. Artificial Intelligence

    CERN Document Server

    Warwick, Kevin

    2011-01-01

    if AI is outside your field, or you know something of the subject and would like to know more then Artificial Intelligence: The Basics is a brilliant primer.' - Nick Smith, Engineering and Technology Magazine November 2011 Artificial Intelligence: The Basics is a concise and cutting-edge introduction to the fast moving world of AI. The author Kevin Warwick, a pioneer in the field, examines issues of what it means to be man or machine and looks at advances in robotics which have blurred the boundaries. Topics covered include: how intelligence can be defined whether machines can 'think' sensory

  9. IVHM Framework for Intelligent Integration for Vehicle Health Management

    Science.gov (United States)

    Paris, Deidre; Trevino, Luis C.; Watson, Michael D.

    2005-01-01

    Integrated Vehicle Health Management (IVHM) systems for aerospace vehicles, is the process of assessing, preserving, and restoring system functionality across flight and techniques with sensor and communication technologies for spacecraft that can generate responses through detection, diagnosis, reasoning, and adapt to system faults in support of Integrated Intelligent Vehicle Management (IIVM). These real-time responses allow the IIVM to modify the affected vehicle subsystem(s) prior to a catastrophic event. Furthermore, this framework integrates technologies which can provide a continuous, intelligent, and adaptive health state of a vehicle and use this information to improve safety and reduce costs of operations. Recent investments in avionics, health management, and controls have been directed towards IIVM. As this concept has matured, it has become clear that IIVM requires the same sensors and processing capabilities as the real-time avionics functions to support diagnosis of subsystem problems. New sensors have been proposed, in addition to augment the avionics sensors to support better system monitoring and diagnostics. As the designs have been considered, a synergy has been realized where the real-time avionics can utilize sensors proposed for diagnostics and prognostics to make better real-time decisions in response to detected failures. IIVM provides for a single system allowing modularity of functions and hardware across the vehicle. The framework that supports IIVM consists of 11 major on-board functions necessary to fully manage a space vehicle maintaining crew safety and mission objectives. These systems include the following: Guidance and Navigation; Communications and Tracking; Vehicle Monitoring; Information Transport and Integration; Vehicle Diagnostics; Vehicle Prognostics; Vehicle Mission Planning, Automated Repair and Replacement; Vehicle Control; Human Computer Interface; and Onboard Verification and Validation. Furthermore, the presented

  10. Finding competitive intelligence on Internet start-up companies: a study of secondary resource use and information-seeking processes

    Directory of Open Access Journals (Sweden)

    2001-01-01

    Full Text Available The paper reports findings from a study of CI activities involving Internet start-up companies in the telecommunications industry. The CI gathering was conducted by graduate students in library and information science in the context of a class project for a real business client, itself a small Internet start-up company. The primary objective of the study was to provide empirical insights into the applicability of specific types of secondary information resources to finding competitive intelligence information on small Internet start-up companies. An additional objective was to identify the characteristics of research strategies applied in the collection of CI on Internet start-ups from the perspective of current conceptual frameworks of information-seeking behaviour presented in the library and information science literature. This study revealed some interesting findings regarding the types of secondary information resources that can be used to find competitive intelligence on small, Internet start-up companies. The study also provided insight into the characteristics of the overall information-seeking strategies that are applied in this type of competitive intelligence research.

  11. Intelligent Advertising

    OpenAIRE

    Díaz Pinedo, Edilfredo Eliot

    2012-01-01

    Intelligent Advertisement diseña e implementa un sistema de publicidad para dispositivos móviles en un centro comercial, donde los clientes reciben publicidad de forma pasiva en sus dispositivos mientras están dentro.

  12. BUSINESS INTELLIGENCE

    OpenAIRE

    Bogdan Mohor Dumitrita

    2011-01-01

    The purpose of this work is to present business intelligence systems. These systems can be extremely complex and important in modern market competition. Its effectiveness also reflects in price, so we have to exlore their financial potential before investment. The systems have 20 years long history and during that time many of such tools have been developed, but they are rarely still in use. Business intelligence system consists of three main areas: Data Warehouse, ETL tools and tools f...

  13. Intelligent indexing

    International Nuclear Information System (INIS)

    Farkas, J.

    1992-01-01

    In this paper we discuss the relevance of artificial intelligence to the automatic indexing of natural language text. We describe the use of domain-specific semantically-based thesauruses and address the problem of creating adequate knowledge bases for intelligent indexing systems. We also discuss the relevance of the Hilbert space ι 2 to the compact representation of documents and to the definition of the similarity of natural language texts. (author). 17 refs., 2 figs

  14. Intelligent indexing

    Energy Technology Data Exchange (ETDEWEB)

    Farkas, J

    1993-12-31

    In this paper we discuss the relevance of artificial intelligence to the automatic indexing of natural language text. We describe the use of domain-specific semantically-based thesauruses and address the problem of creating adequate knowledge bases for intelligent indexing systems. We also discuss the relevance of the Hilbert space {iota}{sup 2} to the compact representation of documents and to the definition of the similarity of natural language texts. (author). 17 refs., 2 figs.

  15. Network control stations in the smart grid. Process and information knots for business intelligence applications; Netzleitstellen im Smart Grid. Prozess- und Informationsknoten fuer Business Intelligence Applikationen

    Energy Technology Data Exchange (ETDEWEB)

    Kautsch, Stephan; Kroll, Meinhard [ABB AG, Mannheim (Germany); Schoellhorn, Daniel [EnBW Regional AG, Stuttgart (Germany)

    2012-07-01

    The degree of automation in the distribution will increase, whereas a more extensive monitoring is possible. Smart metering in the local network station replaces the drag pointers. This allows the pre-determined load flows to be precise and it can be determined and valuable data can be collected about how resources, for example the transformers in the secondary substations, are actually utilized. The amount of information available is increasing steadily, not least because of the increasing expansion of smart meters, that also provide valuable information for the operation of the distribution networks. This ''flood'' of data that is processed by the system, filtered, and analyzed must be prepared for the user in order to make sense, but can also be used to support and optimize many business processes. Although these tasks mentioned are usually not yet allocated within the grid operator organization, they offer themselves to be placed close to the network control centers as they propose new challenges but also opportunities. (orig.)

  16. Artificial Intelligence--Applications in Education.

    Science.gov (United States)

    Poirot, James L.; Norris, Cathleen A.

    1987-01-01

    This first in a projected series of five articles discusses artificial intelligence and its impact on education. Highlights include the history of artificial intelligence and the impact of microcomputers; learning processes; human factors and interfaces; computer assisted instruction and intelligent tutoring systems; logic programing; and expert…

  17. Business Intelligence Solutions for Gaining Competitive Advantage

    Directory of Open Access Journals (Sweden)

    2007-01-01

    Full Text Available Business Intelligence is the process for increasing the competitive advantage of a company by intelligent use of available data in decision-making. Only a revolutionary Business Intelligence solution, like the proposed portal-based, can solve the complex issues faced when evaluating decision support applications and ensures the availability of any business-critical information.

  18. Assessing Cognitive Abilities: Intelligence and More

    Directory of Open Access Journals (Sweden)

    Keith E. Stanovich

    2014-02-01

    Full Text Available In modern cognitive science, rationality and intelligence are measured using different tasks and operations. Furthermore, in several contemporary dual process theories of cognition, rationality is a more encompassing construct than intelligence. Researchers need to continue to develop measures of rational thought without regard to empirical correlations with intelligence. The measurement of individual differences in rationality should not be subsumed by the intelligence concept.

  19. Data transfer based on intelligent ethernet card

    International Nuclear Information System (INIS)

    Zhu Haitao; Chinese Academy of Sciences, Beijing; Chu Yuanping; Zhao Jingwei

    2007-01-01

    Intelligent Ethernet Cards are widely used in systems where the network throughout is very large, such as the DAQ systems for modern high energy physics experiments, web service. With the example of a commercial intelligent Ethernet card, this paper introduces the architecture, the principle and the process of intelligent Ethernet cards. In addition, the results of several experiments showing the differences between intelligent Ethernet cards and general ones are also presented. (authors)

  20. Detailed Design of On-Board and Ground Segment

    DEFF Research Database (Denmark)

    Thuesen, Gøsta

    1998-01-01

    Image processing, attitude determination, quaternion estimation, and performance test of short range camera for rendez-vous and docking of spacecraft.......Image processing, attitude determination, quaternion estimation, and performance test of short range camera for rendez-vous and docking of spacecraft....

  1. Preparing for Science at Sea - a Chief Scientists Training Cruise on Board the RV Sikuliaq

    Science.gov (United States)

    Coakley, B.; Pockalny, R. A.

    2017-12-01

    As part of their education, marine geology and geophysics students spend time at sea, collecting, processing and interpreting data to earn their degrees. While this is a critical component of their preparation, it is an incomplete introduction to the process of doing science at sea. Most students are unfamiliar with the proposal process. Many students spend their time at sea performing assigned tasks without responsibility or participation in cruise planning and execution. In December 2016, we conducted a two-week-long, NSF-funded "Chief Scientist Training Cruise" aboard the R/V Sikuliaq designed to complete their introduction to seagoing science by giving the students the opportunity to plan and execute surveys based hypotheses they formulated. The educational process began with applicants responding to a request for proposals (RFP), which provided a framework for the scientific potential of the cruise. This process continued training through two days of workshops and presentations at the Hawai'i Institute of Geophysics. The students used existing data to define hypotheses, plan surveys, and collect/analyze data to test their hypothesis. The survey design was subject to the time constraints imposed by the ship schedule and the physical constraints imposed by the ship's equipment. The training and sea time made it possible to address all of steps of the scientific process, including proposal writing. Once underway, the combination of conducting the planned surveys and attending daily presentations helped familiarize the students with at-sea operations, the equipment on board the RV Sikuliaq, and the process of writing proposals to NSF for sea-going science. Questionnaires conducted prior to the cruise and in the final days before arriving in port document the success of this training program for developing the abilities and confidence in identifying significant scientific problems, preparing proposals to secure funding, and planning and directing ship surveys.

  2. On-board sound intensity tire-pavement noise study in North Carolina.

    Science.gov (United States)

    2011-12-01

    "This research investigated tire-pavement noise on various types of pavements across North Carolina by using On- : Board Sound Intensity (OBSI) method. To mitigate traffic noise, quieter pavement may provide advantages that : noise barriers cannot. T...

  3. On-Board Thermal Management of Waste Heat from a High-Energy Device

    National Research Council Canada - National Science Library

    Klatt, Nathan D

    2008-01-01

    The use of on-board high-energy devices such as megawatt lasers and microwave emitters requires aircraft system integration of thermal devices to either get rid of waste heat or utilize it in other areas of the aircraft...

  4. Intelligent automotive battery systems

    Science.gov (United States)

    Witehira, P.

    A single power-supply battery is incompatible with modern vehicles. A one-cmbination 12 cell/12 V battery, developed by Power Beat International Limited (PBIL), is described. The battery is designed to be a 'drop in' replacement for existing batteries. The cell structures, however, are designed according to load function, i.e., high-current shallow-discharge cycles and low-current deep-discharge cycles. The preferred energy discharge management logic and integration into the power distribution network of the vehicle to provide safe user-friendly usage is described. The system is designed to operate transparent to the vehicle user. The integrity of the volatile high-current cells is maintained by temperature-sensitive voltage control and discharge management. The deep-cycle cells can be fully utilized without affecting startability under extreme conditions. Electric energy management synchronization with engine starting will provide at least 6% overall reduction in hydrocarbon emissions using an intelligent on-board power-supply technology developed by PBIL.

  5. [Breastfeeding and its influence into the cognitive process of Spanish school-children (6 years old), measured by the Wechsler Intelligence Scale].

    Science.gov (United States)

    Pérez Ruiz, Juan Manuel; Miranda León, María Teresa; Peinado Herreros, José María; Iribar Ibabe, María Concepción

    2013-09-01

    Some scientific evidence support that a better cognitive development during the school age is related with breastfeeding. In this study, the potential benefit of breastfeeding duration is evaluated, related to Verbal Comprehension, Perceptual Reasoning, Working Memory and Processing Speed. A total of 103 children, first year of Primary School, six-year-old, (47 boys and 56 girls), were included from different schools in the province of Granada (Spain) at urban, semi-urban and rural areas. The global cognitive capability, as well as some specific intelligence domains which permit a more precise and deeper analysis of the cognitive processes, was evaluated through the Wechsler Intelligence Scale for Children--version IV. The results prove an association, statistically signnificative, between the best values of IQ and the other four WISC-IV indexes and a longer breastfeeding. There is a highly significant (p = 0.000) association between the best scores and those children who were breastfed during 6 months, which validates our hypothesis. The advice of breastfeeding during at least the first six months of life should be reinforced to reduce learning difficulties.

  6. Artificial intelligence in cardiology.

    Science.gov (United States)

    Bonderman, Diana

    2017-12-01

    Decision-making is complex in modern medicine and should ideally be based on available data, structured knowledge and proper interpretation in the context of an individual patient. Automated algorithms, also termed artificial intelligence that are able to extract meaningful patterns from data collections and build decisions upon identified patterns may be useful assistants in clinical decision-making processes. In this article, artificial intelligence-based studies in clinical cardiology are reviewed. The text also touches on the ethical issues and speculates on the future roles of automated algorithms versus clinicians in cardiology and medicine in general.

  7. A basic component for ISGRI, the CdTe gamma camera on board the INTEGRAL satellite

    International Nuclear Information System (INIS)

    Arques, M.; Baffert, N.; Lattard, D.

    1999-01-01

    A basic component, called Polycell, has been developed for the ISGRI (INTEGRAL Soft Gamma Ray Imager) CdTe camera on board the INTEGRAL (INTErnational Gamma-Ray Astrophysics Laboratory) satellite. Operating at room temperature, it covers the 20 keV--1 MeV energy range. It features a sub-ensemble of 16 CdTe detectors and their associated front end electronics. This electronics is based on 4-channel analog-digital ASICs. Their analog part features a low noise preamplifier, allowing a threshold below 20 keV and a pulse rise-time measurement which permits a charge loss correction. The digital part ensures the internal acquisition timing sequence as well as the dialogue with external electronics. Two versions of the ISGRI ASIC have been developed in a collaboration of two CEA microelectronics teams from CEA/DTA/LETI/DSYS and CEA/DSM/DAPNIA/SEI, respectively on a standard CMOS AMS process hardened against radiation by lay-out, and on a Silicon On Insulator process (DMILL MHS), the latter being latch-up free. This paper presents the ASIC and polycell architecture as well as experimental results obtained with polycells equipped with AMS ASICs

  8. On-Board Real-Time Optimization Control for Turbo-Fan Engine Life Extending

    Science.gov (United States)

    Zheng, Qiangang; Zhang, Haibo; Miao, Lizhen; Sun, Fengyong

    2017-11-01

    A real-time optimization control method is proposed to extend turbo-fan engine service life. This real-time optimization control is based on an on-board engine mode, which is devised by a MRR-LSSVR (multi-input multi-output recursive reduced least squares support vector regression method). To solve the optimization problem, a FSQP (feasible sequential quadratic programming) algorithm is utilized. The thermal mechanical fatigue is taken into account during the optimization process. Furthermore, to describe the engine life decaying, a thermal mechanical fatigue model of engine acceleration process is established. The optimization objective function not only contains the sub-item which can get fast response of the engine, but also concludes the sub-item of the total mechanical strain range which has positive relationship to engine fatigue life. Finally, the simulations of the conventional optimization control which just consider engine acceleration performance or the proposed optimization method have been conducted. The simulations demonstrate that the time of the two control methods from idle to 99.5 % of the maximum power are equal. However, the engine life using the proposed optimization method could be surprisingly increased by 36.17 % compared with that using conventional optimization control.

  9. Designing on-Board Data Handling for EDF (Electric Ducted Fan) Rocket

    Science.gov (United States)

    Mulyana, A.; Faiz, L. A. A.

    2018-02-01

    The EDF (Electric Ducted Fan) rocket to launch requires a system of monitoring, tracking and controlling to allow the rocket to glide properly. One of the important components in the rocket is OBDH (On-Board Data Handling) which serves as a medium to perform commands and data processing. However, TTC (Telemetry, Tracking, and Command) are required to communicate between GCS (Ground Control Station) and OBDH on EDF rockets. So the design control system of EDF rockets and GCS for telemetry and telecommand needs to be made. In the design of integrated OBDH controller uses a lot of electronics modules, to know the behavior of rocket used IMU sensor (Inertial Measurement Unit) in which consist of 3-axis gyroscope sensor and Accelerometer 3-axis. To do tracking using GPS, compass sensor as a determinant of the direction of the rocket as well as a reference point on the z-axis of gyroscope sensor processing and used barometer sensors to measure the height of the rocket at the time of glide. The data can be known in real-time by sending data through radio modules at 2.4 GHz frequency using XBee-Pro S2B to GCS. By using windows filter, noises can be reduced, and it used to guarantee monitoring and controlling system can work properly.

  10. Intelligent environmental data warehouse

    International Nuclear Information System (INIS)

    Ekechukwu, B.

    1998-01-01

    Making quick and effective decisions in environment management are based on multiple and complex parameters, a data warehouse is a powerful tool for the over all management of massive environmental information. Selecting the right data from a warehouse is an important factor consideration for end-users. This paper proposed an intelligent environmental data warehouse system. It consists of data warehouse to feed an environmental researchers and managers with desire environmental information needs to their research studies and decision in form of geometric and attribute data for study area, and a metadata for the other sources of environmental information. In addition, the proposed intelligent search engine works according to a set of rule, which enables the system to be aware of the environmental data wanted by the end-user. The system development process passes through four stages. These are data preparation, warehouse development, intelligent engine development and internet platform system development. (author)

  11. Satellite on-board real-time SAR processor prototype

    Science.gov (United States)

    Bergeron, Alain; Doucet, Michel; Harnisch, Bernd; Suess, Martin; Marchese, Linda; Bourqui, Pascal; Desnoyers, Nicholas; Legros, Mathieu; Guillot, Ludovic; Mercier, Luc; Châteauneuf, François

    2017-11-01

    A Compact Real-Time Optronic SAR Processor has been successfully developed and tested up to a Technology Readiness Level of 4 (TRL4), the breadboard validation in a laboratory environment. SAR, or Synthetic Aperture Radar, is an active system allowing day and night imaging independent of the cloud coverage of the planet. The SAR raw data is a set of complex data for range and azimuth, which cannot be compressed. Specifically, for planetary missions and unmanned aerial vehicle (UAV) systems with limited communication data rates this is a clear disadvantage. SAR images are typically processed electronically applying dedicated Fourier transformations. This, however, can also be performed optically in real-time. Originally the first SAR images were optically processed. The optical Fourier processor architecture provides inherent parallel computing capabilities allowing real-time SAR data processing and thus the ability for compression and strongly reduced communication bandwidth requirements for the satellite. SAR signal return data are in general complex data. Both amplitude and phase must be combined optically in the SAR processor for each range and azimuth pixel. Amplitude and phase are generated by dedicated spatial light modulators and superimposed by an optical relay set-up. The spatial light modulators display the full complex raw data information over a two-dimensional format, one for the azimuth and one for the range. Since the entire signal history is displayed at once, the processor operates in parallel yielding real-time performances, i.e. without resulting bottleneck. Processing of both azimuth and range information is performed in a single pass. This paper focuses on the onboard capabilities of the compact optical SAR processor prototype that allows in-orbit processing of SAR images. Examples of processed ENVISAT ASAR images are presented. Various SAR processor parameters such as processing capabilities, image quality (point target analysis), weight and

  12. Semantic Business Intelligence - a New Generation of Business Intelligence

    OpenAIRE

    Dinu AIRINEI; Dora-Anca BERTA

    2012-01-01

    Business Intelligence Solutions represents applications used by companies to manage process and analyze data to provide substantiated decision. In the context of Semantic Web develop-ment trend is to integrate semantic unstructured data, making business intelligence solutions to be redesigned in such a manner that can analyze, process and synthesize, in addition to traditional data and data integrated with semantic another form and structure. This invariably leads appearance of new BI solutio...

  13. Intelligent Universe

    Energy Technology Data Exchange (ETDEWEB)

    Hoyle, F

    1983-01-01

    The subject is covered in chapters, entitled: chance and the universe (synthesis of proteins; the primordial soup); the gospel according to Darwin (discussion of Darwin theory of evolution); life did not originate on earth (fossils from space; life in space); the interstellar connection (living dust between the stars; bacteria in space falling to the earth; interplanetary dust); evolution by cosmic control (microorganisms; genetics); why aren't the others here (a cosmic origin of life); after the big bang (big bang and steady state); the information rich universe; what is intelligence up to; the intelligent universe.

  14. Artificial intelligence

    International Nuclear Information System (INIS)

    Perret-Galix, D.

    1992-01-01

    A vivid example of the growing need for frontier physics experiments to make use of frontier technology is in the field of artificial intelligence and related themes. This was reflected in the second international workshop on 'Software Engineering, Artificial Intelligence and Expert Systems in High Energy and Nuclear Physics' which took place from 13-18 January at France Telecom's Agelonde site at La Londe des Maures, Provence. It was the second in a series, the first having been held at Lyon in 1990

  15. Artificial Intelligence and Moral intelligence

    Directory of Open Access Journals (Sweden)

    Laura Pana

    2008-07-01

    Full Text Available We discuss the thesis that the implementation of a moral code in the behaviour of artificial intelligent systems needs a specific form of human and artificial intelligence, not just an abstract intelligence. We present intelligence as a system with an internal structure and the structural levels of the moral system, as well as certain characteristics of artificial intelligent agents which can/must be treated as 1- individual entities (with a complex, specialized, autonomous or selfdetermined, even unpredictable conduct, 2- entities endowed with diverse or even multiple intelligence forms, like moral intelligence, 3- open and, even, free-conduct performing systems (with specific, flexible and heuristic mechanisms and procedures of decision, 4 – systems which are open to education, not just to instruction, 5- entities with “lifegraphy”, not just “stategraphy”, 6- equipped not just with automatisms but with beliefs (cognitive and affective complexes, 7- capable even of reflection (“moral life” is a form of spiritual, not just of conscious activity, 8 – elements/members of some real (corporal or virtual community, 9 – cultural beings: free conduct gives cultural value to the action of a ”natural” or artificial being. Implementation of such characteristics does not necessarily suppose efforts to design, construct and educate machines like human beings. The human moral code is irremediably imperfect: it is a morality of preference, of accountability (not of responsibility and a morality of non-liberty, which cannot be remedied by the invention of ethical systems, by the circulation of ideal values and by ethical (even computing education. But such an imperfect morality needs perfect instruments for its implementation: applications of special logic fields; efficient psychological (theoretical and technical attainments to endow the machine not just with intelligence, but with conscience and even spirit; comprehensive technical

  16. Exploratory study of the relationship between the musical, visuospatial, bodily-kinesthetic intelligence and drive creativity in the process of learning

    Directory of Open Access Journals (Sweden)

    Paula MARCHENA CRUZ

    2017-12-01

    Full Text Available Currently, the Spanish educational system focuses its attention on the development of priority subjects such as language and mathematics versus other secondary such as music (Palacios, 2006, without considering numerous neuropsychological research that provides new theories of mind and learning that can positively influence the transformation of current educational models (Martin-Lobo, 2015. This research aims to determine the relation between musical intelligence, bodily-kinesthetic intelligence, intelligence visuospatial and motor creativity in a sample among 5 years old students from the last year of Early Childhood Education. The instrument used to assess the three intelligences, based on Gardner’s theory, was the Multiple Intelligences questionnaire for children of pre-school age (Prieto and Ballester, 2003; for the evaluation of motor creativity was used Test of Creative Thinking in Action and Movement (Torrance, Reisman and Floyd, 1981. A descriptive and correlational statistical analysis (using the Pearson correlation index applying the Microsoft Excel program along with the supplement known as Ezanalyze. The results indicated no significant relationship between musical intelligence and motor creativity (p = 0.988; the visuospatial intelligence and motor creativity (p = 0.992; and the bodily-kinesthetic intelligence and motor creativity (p = 0.636. Although there was significant relation between the musical and visuospatial intelligence (p = 0.000; the musical and bodily-kinesthetic intelligence (p = 0.000; and the bodily-kinesthetic and visuospatial intelligence (p = 0.025.

  17. INTENSITY OF THE DYNAMICS OF PHYSICAL PREPAREDNESS IN THE PROCESS OF STUDENTS GROWING UP WITH DIFFERENT LEVELS OF INTELLIGENCE

    Directory of Open Access Journals (Sweden)

    E. M. Revenko

    2016-01-01

    Full Text Available The purpose of the investigation is the scientific substantiation forthe implementation of a differentiated approach to the organization of physical education on the basis of accounting students individually-typological features of the age.Methods. Motor abilities of students are studied by measuring: force (backbone dynamometry, strength endurance (pulling up on the bar, speed-strength abilities (long jump from their seats, as well as high-speed capacity (running at 30, 60 or 100 meters, depending on the age, aerobic endurance (running at 1000 or 3000 m, depending on age. The dynamics of the integrated physical preparedness (DIPP of each student is estimated by calculating the arithmetic mean value of the growth rate of the development of motor abilities listed above (the results of 5 tests. Evaluation of general intelligence (GI of schoolchildren in 8, 10 and 11 classes, students of 1 – 3 courses carried out by the test of R. Amthauer adapted by L. A. Yasyukova [13], and the 6 classes pupils – through the intellectual test (GIT [1].Results. It was experimentally established that students of 6, 8, 10, 11 grades and 1 – 3 courses at higher intelligence level have a low dynamics of physical fitness. On the contrary, students with a lower level of intelligence revealed a high dynamics of physical fitness. Marked discrepancies in the dynamics of the development of mental and motor areas of maturing personality are interpreted as individual-typological features of age-related development. Based on these facts it is concluded that the organization of physical education on the basis of program-regulatory approach with common unified requirements involved, will not allow to create conditions for highquality physical education of the younger generation and the formation of a sustainable motivation for self-employment by physical exercises.Scientific novelty. Scientific evidence of sustained differences in the dynamics of the

  18. Fiber-Optic Communication Links Suitable for On-Board Use in Modern Aircraft

    Science.gov (United States)

    Nguyen, Hung; Ngo, Duc; Alam, Mohammad F.; Atiquzzaman, Mohammed; Sluse, James; Slaveski, Filip

    2004-01-01

    The role of the Advanced Air Transportation Technologies program undertaken at the NASA Glenn Research Centers has been focused mainly on the improvement of air transportation safety, with particular emphasis on air transportation communication systems in on-board aircraft. The conventional solutions for digital optical communications systems specifically designed for local/metro area networks are, unfortunately, not capable of transporting the microwave and millimeter RF signals used in avionics systems. Optical networks capable of transporting RF signals are substantially different from the standard digital optical communications systems. The objective of this paper is to identify a number of different communication link architectures for RF/fiber optic transmission using a single backbone fiber for carrying VHF and UHF RF signals in the aircraft. To support these architectures, two approaches derived from both hybrid RF-optical and all-optical processing methodologies are discussed with single and multiple antennas for explicitly transporting VHF and UHF signals, while the relative merits and demerits of each architecture are also addressed. Furthermore, the experimental results of wavelength division multiplexing (WDM) link architecture from our test-bed platform, configured for aircraft environment to support simultaneous transmission of multiple RF signals over a single optical fiber, exhibit no appreciable signal degradation at wavelengths of both 1330 and 1550 nm, respectively. Our measurements of signal to noise ratio carried out for the transmission of FM and AM analog modulated signals at these wavelengths indicate that WDM is a fiber optic technology which is potentially suitable for avionics applications.

  19. Multi-gigabit optical interconnects for next-generation on-board digital equipment

    Science.gov (United States)

    Venet, Norbert; Favaro, Henri; Sotom, Michel; Maignan, Michel; Berthon, Jacques

    2017-11-01

    Parallel optical interconnects are experimentally assessed as a technology that may offer the high-throughput data communication capabilities required to the next-generation on-board digital processing units. An optical backplane interconnect was breadboarded, on the basis of a digital transparent processor that provides flexible connectivity and variable bandwidth in telecom missions with multi-beam antenna coverage. The unit selected for the demonstration required that more than tens of Gbit/s be supported by the backplane. The demonstration made use of commercial parallel optical link modules at 850 nm wavelength, with 12 channels running at up to 2.5 Gbit/s. A flexible optical fibre circuit was developed so as to route board-to-board connections. It was plugged to the optical transmitter and receiver modules through 12-fibre MPO connectors. BER below 10-14 and optical link budgets in excess of 12 dB were measured, which would enable to integrate broadcasting. Integration of the optical backplane interconnect was successfully demonstrated by validating the overall digital processor functionality.

  20. Plant intelligence

    Science.gov (United States)

    Lipavská, Helena; Žárský, Viktor

    2009-01-01

    The concept of plant intelligence, as proposed by Anthony Trewavas, has raised considerable discussion. However, plant intelligence remains loosely defined; often it is either perceived as practically synonymous to Darwinian fitness, or reduced to a mere decorative metaphor. A more strict view can be taken, emphasizing necessary prerequisites such as memory and learning, which requires clarifying the definition of memory itself. To qualify as memories, traces of past events have to be not only stored, but also actively accessed. We propose a criterion for eliminating false candidates of possible plant intelligence phenomena in this stricter sense: an “intelligent” behavior must involve a component that can be approximated by a plausible algorithmic model involving recourse to stored information about past states of the individual or its environment. Re-evaluation of previously presented examples of plant intelligence shows that only some of them pass our test. “You were hurt?” Kumiko said, looking at the scar. Sally looked down. “Yeah.” “Why didn't you have it removed?” “Sometimes it's good to remember.” “Being hurt?” “Being stupid.”—(W. Gibson: Mona Lisa Overdrive) PMID:19816094

  1. Speech Intelligibility

    Science.gov (United States)

    Brand, Thomas

    Speech intelligibility (SI) is important for different fields of research, engineering and diagnostics in order to quantify very different phenomena like the quality of recordings, communication and playback devices, the reverberation of auditoria, characteristics of hearing impairment, benefit using hearing aids or combinations of these things.

  2. ECONOMIC INTELLIGENCE - THEORETICAL AND PRACTICAL ASPECTS

    Directory of Open Access Journals (Sweden)

    VIRGIL - ION POPOVICI

    2014-12-01

    Full Text Available Economic Intelligence (EI may be a solution in knowledge management as involves collecting, evaluating, processing, analysis and dissemination of economic data within organizations. The ultimate goal of economic intelligence (EI is to take advantage of this opportunity to develop and improve methods for identifying relevant information sources, analysis of information collected and manipulation, to give the user all the necessary decisions. Scope of the Economic Intelligence focused on information available outside the organization, covering wide areas from technology to market or legal issues. Economic Intelligence (EI is closely related to other approaches to information management, and knowledge management and business intelligence, excelling in the use of software tools.

  3. Fiducial-Based Translational Localization Accuracy of Electromagnetic Tracking System and On-Board Kilovoltage Imaging System

    International Nuclear Information System (INIS)

    Santanam, Lakshmi; Malinowski, Kathleen; Hubenshmidt, James; Dimmer, Steve; Mayse, Martin L.; Bradley, Jeffrey; Chaudhari, Amir; Lechleiter, Kirsten; Goddu, Sree Krishna Murty; Esthappan, Jacqueline; Mutic, Sasa; Low, Daniel A.; Parikh, Parag

    2008-01-01

    Purpose: The Calypso medical four-dimensional localization system uses AC electromagnetics, which do not require ionizing radiation, for accurate, real-time tumor tracking. This investigation compared the static and dynamic tracking accuracy of this system to that of an on-board imaging kilovoltage X-ray system for concurrent use of the two systems. Methods and Materials: The localization accuracies of a kilovoltage imaging system and a continuous electromagnetic tracking system were compared. Using an in-house developed four-dimensional stage, quality-assurance fixture containing three radiofrequency transponders was positioned at a series of static locations and then moved through the ellipsoidal and nonuniform continuous paths. The transponder positions were tracked concurrently by the Calypso system. For static localization, the transponders were localized using portal images and digitally reconstructed radiographs by commercial matching software. For dynamic localization, the transponders were fluoroscopically imaged, and their positions were determined retrospectively using custom-written image processing programs. The localization data sets were synchronized with and compared to the known quality assurance fixture positions. The experiment was repeated to retrospectively track three transponders implanted in a canine lung. Results: The root mean square error of the on-board imaging and Calypso systems was 0.1 cm and 0.0 cm, respectively, for static localization, 0.22 mm and 0.33 mm for dynamic phantom positioning, and 0.42 mm for the canine study. Conclusion: The results showed that both localization systems provide submillimeter accuracy. The Calypso and on-board imaging tracking systems offer distinct sets of advantages and, given their compatibility, patients could benefit from the complementary nature of the two systems when used concurrently

  4. Prospecção e monitoramento informacional no processo de inteligência competitiva Information scanning and information mining in the process of competitive intelligence

    Directory of Open Access Journals (Sweden)

    Marta Lígia Pomim Valentim

    2004-01-01

    Full Text Available A prospecção e o monitoramento informacional são atividades base para a inteligência competitiva, entendida como um processo dinâmico, composto pela gestão da informação e pela gestão do conhecimento. O processo de inteligência competitiva (I. C. nas organizações ocorre a partir de diferentes atividades informacionais, dentre elas estão as ligadas a prospecção e ao monitoramento. O papel destas atividades é essencial, pois alimentam todo o processo com dados, informação e conhecimento, constroem diversas estruturas formais e informais de informação dentro da organização, além do que, as atividades de prospecção e monitoramento geram serviços e produtos informacionais sistematizados, com alto valor agregado.The information scanning and information mining are activities base for the competitive intelligence, understood as a dynamic process, composed by the information management and knowledge management. The process of competitive intelligence (I. C. in the organizations it happens starting from different informational activities, they are the tied up ones information scanning and information mining. The function of these activities is essential, because they feed the whole process with data, information and knowledge, they build several formal structures and you inform inside of information of the organization, in addition, the information scanning and information mining activities generate information services and products systematized, with high value aggregate.

  5. Agile deployment and code coverage testing metrics of the boot software on-board Solar Orbiter's Energetic Particle Detector

    Science.gov (United States)

    Parra, Pablo; da Silva, Antonio; Polo, Óscar R.; Sánchez, Sebastián

    2018-02-01

    In this day and age, successful embedded critical software needs agile and continuous development and testing procedures. This paper presents the overall testing and code coverage metrics obtained during the unit testing procedure carried out to verify the correctness of the boot software that will run in the Instrument Control Unit (ICU) of the Energetic Particle Detector (EPD) on-board Solar Orbiter. The ICU boot software is a critical part of the project so its verification should be addressed at an early development stage, so any test case missed in this process may affect the quality of the overall on-board software. According to the European Cooperation for Space Standardization ESA standards, testing this kind of critical software must cover 100% of the source code statement and decision paths. This leads to the complete testing of fault tolerance and recovery mechanisms that have to resolve every possible memory corruption or communication error brought about by the space environment. The introduced procedure enables fault injection from the beginning of the development process and enables to fulfill the exigent code coverage demands on the boot software.

  6. Improved chemical identification from sensor arrays using intelligent algorithms

    Science.gov (United States)

    Roppel, Thaddeus A.; Wilson, Denise M.

    2001-02-01

    Intelligent signal processing algorithms are shown to improve identification rates significantly in chemical sensor arrays. This paper focuses on the use of independently derived sensor status information to modify the processing of sensor array data by using a fast, easily-implemented "best-match" approach to filling in missing sensor data. Most fault conditions of interest (e.g., stuck high, stuck low, sudden jumps, excess noise, etc.) can be detected relatively simply by adjunct data processing, or by on-board circuitry. The objective then is to devise, implement, and test methods for using this information to improve the identification rates in the presence of faulted sensors. In one typical example studied, utilizing separately derived, a-priori knowledge about the health of the sensors in the array improved the chemical identification rate by an artificial neural network from below 10 percent correct to over 99 percent correct. While this study focuses experimentally on chemical sensor arrays, the results are readily extensible to other types of sensor platforms.

  7. Thermal diagnostic of the optical window on board LISA Pathfinder

    International Nuclear Information System (INIS)

    Nofrarias, M; MarIn, A F GarcIa; Lobo, A; Heinzel, G; Ramos-Castro, J; Sanjuan, J; Danzmann, K

    2007-01-01

    Vacuum conditions inside the LTP gravitational reference sensor must be under 10 -5 Pa, a rather demanding requirement. The optical window (OW) is an interface which seals the vacuum enclosure and, at the same time, lets the laser beam go through for interferometric metrology with the test masses. The OW is a plane-parallel plate clamped in a titanium flange, and is considerably sensitive to thermal and stress fluctuations. It is critical for the required precision measurements, hence its temperature will be carefully monitored in flight. This paper reports on the results of a series of OW characterization laboratory runs, intended to study its response to selected thermal signals, as well as their fit to numerical models, and the meaning of the latter. We find that a single-pole ARMA transfer function provides a consistent approximation to the OW response to thermal excitations, and derive a relationship with the physical processes taking place in the OW. We also show how the system noise reduction can be accomplished by means of that transfer function

  8. Deployment and Intelligent Nanosatellite Operations Colorado Final Technical Report

    National Research Council Canada - National Science Library

    Hansen, Elaine; Beckwith, Dave; Koehler, Christ; Levin-Stankevich, Steve; Michels, Jennifer; Wichman, Steve

    2006-01-01

    The main purpose of the DINO satellite was to generate topographic maps of the tops of clouds through stereoscopic imaging based on photographs from the on-board digital cameras, with most processing...

  9. Intelligent Integrated System Health Management

    Science.gov (United States)

    Figueroa, Fernando

    2012-01-01

    Intelligent Integrated System Health Management (ISHM) is the management of data, information, and knowledge (DIaK) with the purposeful objective of determining the health of a system (Management: storage, distribution, sharing, maintenance, processing, reasoning, and presentation). Presentation discusses: (1) ISHM Capability Development. (1a) ISHM Knowledge Model. (1b) Standards for ISHM Implementation. (1c) ISHM Domain Models (ISHM-DM's). (1d) Intelligent Sensors and Components. (2) ISHM in Systems Design, Engineering, and Integration. (3) Intelligent Control for ISHM-Enabled Systems

  10. Novel applications of intelligent systems

    CERN Document Server

    Kasabov, Nikola; Filev, Dimitar; Jotsov, Vladimir

    2016-01-01

    In this carefully edited book some selected results of theoretical and applied research in the field of broadly perceived intelligent systems are presented. The problems vary from industrial to web and problem independent applications. All this is united under the slogan: "Intelligent systems conquer the world”. The book brings together innovation projects with analytical research, invention, retrieval and processing of knowledge and logical applications in technology. This book is aiming to a wide circle of readers and particularly to the young generation of IT/ICT experts who will build the next generations of intelligent systems.

  11. Computational Foundations of Natural Intelligence.

    Science.gov (United States)

    van Gerven, Marcel

    2017-01-01

    New developments in AI and neuroscience are revitalizing the quest to understanding natural intelligence, offering insight about how to equip machines with human-like capabilities. This paper reviews some of the computational principles relevant for understanding natural intelligence and, ultimately, achieving strong AI. After reviewing basic principles, a variety of computational modeling approaches is discussed. Subsequently, I concentrate on the use of artificial neural networks as a framework for modeling cognitive processes. This paper ends by outlining some of the challenges that remain to fulfill the promise of machines that show human-like intelligence.

  12. Computational Foundations of Natural Intelligence

    Directory of Open Access Journals (Sweden)

    Marcel van Gerven

    2017-12-01

    Full Text Available New developments in AI and neuroscience are revitalizing the quest to understanding natural intelligence, offering insight about how to equip machines with human-like capabilities. This paper reviews some of the computational principles relevant for understanding natural intelligence and, ultimately, achieving strong AI. After reviewing basic principles, a variety of computational modeling approaches is discussed. Subsequently, I concentrate on the use of artificial neural networks as a framework for modeling cognitive processes. This paper ends by outlining some of the challenges that remain to fulfill the promise of machines that show human-like intelligence.

  13. Special Issue on Intelligent Robots

    Directory of Open Access Journals (Sweden)

    Genci Capi

    2013-08-01

    Full Text Available The research on intelligent robots will produce robots that are able to operate in everyday life environments, to adapt their program according to environment changes, and to cooperate with other team members and humans. Operating in human environments, robots need to process, in real time, a large amount of sensory data—such as vision, laser, microphone—in order to determine the best action. Intelligent algorithms have been successfully applied to link complex sensory data to robot action. This editorial briefly summarizes recent findings in the field of intelligent robots as described in the articles published in this special issue.

  14. Biotechnological experiments in space flights on board of space stations

    Science.gov (United States)

    Nechitailo, Galina S.

    2012-07-01

    factors of space flight change direction of biological processes, and show a possibility to get special kinds of bioproducts with new properties.

  15. Evaluation of the use of on-board spacecraft energy storage for electric propulsion missions

    Science.gov (United States)

    Poeschel, R. L.; Palmer, F. M.

    1983-01-01

    On-board spacecraft energy storage represents an under utilized resource for some types of missions that also benefit from using relatively high specific impulse capability of electric propulsion. This resource can provide an appreciable fraction of the power required for operating the electric propulsion subsystem in some missions. The most probable mission requirement for utilization of this energy is that of geostationary satellites which have secondary batteries for operating at high power levels during eclipse. The study summarized in this report selected four examples of missions that could benefit from use of electric propulsion and on-board energy storage. Engineering analyses were performed to evaluate the mass saved and economic benefit expected when electric propulsion and on-board batteries perform some propulsion maneuvers that would conventionally be provided by chemical propulsion. For a given payload mass in geosynchronous orbit, use of electric propulsion in this manner typically provides a 10% reduction in spacecraft mass.

  16. New control method of on-board ATP system of Shinkansen trains

    Energy Technology Data Exchange (ETDEWEB)

    Fukuda, N.; Watanabe, T. [Railway Technical Research Inst. (Japan)

    2000-07-01

    We studied a new control method of the on-board automatic train protection (ATP) system for Shinkansen trains to shorten the operation time and not to degrade ride comfort at changes in deceleration of the train, while maintaining the safety and reliability of the present ATP signal system. We propose a new on-board pattern brake control system based on the present ATP data without changing the wayside equipment. By simulating the ATP braking of the proposed control method, we succeeded in shortening the operation time by 48 seconds per one station in comparison with the present ATP brake control system. This paper reports the concept of the system and simulation results of the on-board pattern. (orig.)

  17. Artificial Intelligence.

    Science.gov (United States)

    Lawrence, David R; Palacios-González, César; Harris, John

    2016-04-01

    It seems natural to think that the same prudential and ethical reasons for mutual respect and tolerance that one has vis-à-vis other human persons would hold toward newly encountered paradigmatic but nonhuman biological persons. One also tends to think that they would have similar reasons for treating we humans as creatures that count morally in our own right. This line of thought transcends biological boundaries-namely, with regard to artificially (super)intelligent persons-but is this a safe assumption? The issue concerns ultimate moral significance: the significance possessed by human persons, persons from other planets, and hypothetical nonorganic persons in the form of artificial intelligence (AI). This article investigates why our possible relations to AI persons could be more complicated than they first might appear, given that they might possess a radically different nature to us, to the point that civilized or peaceful coexistence in a determinate geographical space could be impossible to achieve.

  18. Close ISR Support: Re-organizing the Combined Forces Air Component Commander’s Intelligence, Surveillance and Reconnaissance Processes and Agencies

    Science.gov (United States)

    2009-12-01

    Intelligence IO–Information Operations IOT –In Order To IP–Iraqi Police IPB–Intelligence Preparation of the Battlespace IR–infrared xxiii IROC... forensic backtracking highlighted potential cache sites or improvised explosive device (IED) emplacement areas which could then be better analyzed by the...target indicator (GMTI) forensic backtracking to link suspicious GMTI movements with other intelligence signatures.388 As will be discussed in

  19. Experimenting Galileo on Board the International Space Station

    Science.gov (United States)

    Fantinato, Samuele; Pozzobon, Oscar; Sands, Obed S.; Welch, Bryan W.; Clapper, Carolyn J.; Miller, James J.; Gamba, Giovanni; Chiara, Andrea; Montagner, Stefano; Giordano, Pietro; hide

    2016-01-01

    The SCaN Testbed is an advanced integrated communications system and laboratory facility installed on the International Space Station (ISS) in 2012. The testbed incorporates a set of new generation of Software Defined Radio (SDR) technologies intended to allow researchers to develop, test, and demonstrate new communications, networking, and navigation capabilities in the actual environment of space. Qascom, in cooperation with ESA and NASA, is designing a Software Defined Radio GalileoGPS Receiver capable to provide accurate positioning and timing to be installed on the ISS SCaN Testbed. The GalileoGPS waveform will be operated in the JPL SDR that is constituted by several hardware components that can be used for experimentations in L-Band and S-Band. The JPL SDR includes an L-Band Dorne Margolin antenna mounted onto a choke ring. The antenna is connected to a radio front end capable to provide one bit samples for the three GNSS frequencies (L1, L2 and L5) at 38 MHz, exploiting the subharmonic sampling. The baseband processing is then performed by an ATMEL AT697 processor (100 MIPS) and two Virtex 2 FPGAs. The JPL SDR supports the STRS (Space Telecommunications Radio System) that provides common waveform software interfaces, methods of instantiation, operation, and testing among different compliant hardware and software products. The standard foresees the development of applications that are modular, portable, reconfigurable, and reusable. The developed waveform uses the STRS infrastructure-provided application program interfaces (APIs) and services to load, verify, execute, change parameters, terminate, or unload an application. The project is divided in three main phases. 1)Design and Development of the GalileoGPS waveform for the SCaN Testbed starting from Qascom existing GNSS SDR receiver. The baseline design is limited to the implementation of the single frequency Galileo and GPS L1E1 receiver even if as part of the activity it will be to assess the

  20. The EGSE science software of the IBIS instrument on-board INTEGRAL satellite

    International Nuclear Information System (INIS)

    La Rosa, Giovanni; Fazio, Giacomo; Segreto, Alberto; Gianotti, Fulvio; Stephen, John; Trifoglio, Massimo

    2000-01-01

    IBIS (Imager on Board INTEGRAL Satellite) is one of the key instrument on-board the INTEGRAL satellite, the follow up mission of the high energy missions CGRO and Granat. The EGSE of IBIS is composed by a Satellite Interface Simulator, a Control Station and a Science Station. Here are described the solutions adopted for the architectural design of the software running on the Science Station. Some preliminary results are used to show the science functionality, that allowed to understand the instrument behavior, all along the test and calibration campaigns of the Engineering Model of IBIS

  1. Geographical influence on the radiation exposure of an air crew on board a subsonic aircraft

    International Nuclear Information System (INIS)

    Bottollier-Depois, J.F.; Spurny, F.; Votockova, I.

    1996-01-01

    Radiation fields on board a subsonic aircraft have been studied on board an Airbus A310-300 during the flights Prague - Abu Dhabi - Bangkok and Bangkok - Abu Dhabi - Prague, during February 1995. A complex set of measuring instruments has been used for these studies: tissue equivalent proportional counter, moderator-type neutron rem-meter, environmental radiation dose rate meter, thermoluminescent and track etch detectors and bubble detectors. The results obtained are presented and analyzed; they are compared with the results obtained in the flights Prague - Montreal - Prague. Conclusions concerning the influence of geographical parameters on the aircrew exposure levels are formulated. (author). 13 refs., 2 figs., 3 tabs

  2. Air crew exposure on board a subsonic aircraft studied with complex dosimetric sets

    International Nuclear Information System (INIS)

    Spurny, F.; Votockova, I.; Bottollier-Depois, J.F.

    1996-01-01

    Radiation fields on board a subsonic aircraft have been studied using a complex set of measuring instruments i.e. tissue equivalent proportional counter (TEPC), neutron rem-meter, environmental radiation dose rate meter, thermoluminescent detectors (TLDs), track etch detectors (TEDs) and bubble damage neutron detectors (BDNDs). The measurements have been realised on board the Airbus A310-300 during the flights Prague-Montreal and Montreal-Prague, in February 1995. The results obtained are presented, analysed and discussed both from the point of view of the detector responses and the general exposure levels. (authors). 23 refs., 1 fig., 4 tabs

  3. Development and application of an emitter for research of an on-board ultraviolet polarimeter

    Science.gov (United States)

    Nevodovskyi, P. V.; Geraimchuk, M. D.; Vidmachenko, A. P.; Ivakhiv, O. V.

    2018-05-01

    In carrying out of the work a layout of on-board small-sized ultraviolet polarimeter (UVP) was created. UVP is the device, which provides an implementation of passive remote studies of stratospheric aerosol from the board of the microsatellite of the Earth by the method of polarimetry. For carrying out of tests and the research of polarimetric equipment, a special stand was created at MAO of NAS of Ukraine. In its composition is an ultraviolet emitter. Emitter is one of the main components of a special stand for the study of on-board ultraviolet polarimeters.

  4. Data security in Intelligent Transport Systems

    Directory of Open Access Journals (Sweden)

    Tomas Zelinka

    2012-10-01

    Full Text Available Intelligent Transport Services expect availability of the secure seamless communications solutions typically covering widely spread areas. Different ITS solutions require different portfolio of telecommunications service quality. These parameters have to correspond with ITS service performance parameters required by specific service. Even though quite extensive range of public wireless data services with reasonable coverage are provided, most of them are provided with no guaranteed quality and security. ITS requirements can be in most parameters easier reached if multi-path communications systems are applied core solution is combined with both public as well as private ones where and when it is needed. Such solution requires implementation of relevant flexible system architecture supported by the efficient decision processes. This paper is concentrated the telecommunications security issues relevant to the ITS wide area networking. Expected level of security varies in dependence on relevant ITS service requirements. Data volumes transferred both in private data vehicle on board networks as well as between vehicles and infrastructure (C2I or other vehicles (C2C progressively grow. Such trend upsurges the fatal problems appearance probability in case security of the wide area networks is not relevantly treated. That is reason why relevant communications security treatment becomes crucial part of the ITS solution. Besides of available "off shelf" security tools we present solution based on non-public universal identifier with dynamical extension (time and position dependency as an autonomous variables and data selection according to actor role or category. Presented results were obtained within projects e-Ident1, DOTEK2 and SRATVU3.

  5. The promise of cyborg intelligence.

    Science.gov (United States)

    Brown, Michael F; Brown, Alexander A

    2017-03-01

    Yu et al. (2016) demonstrated that algorithms designed to find efficient routes in standard mazes can be integrated with the natural processes controlling rat navigation and spatial choices, and they pointed out the promise of such "cyborg intelligence" for biorobotic applications. Here, we briefly describe Yu et al.'s work, explore its relevance to the study of comparative cognition, and indicate how work involving cyborg intelligence would benefit from interdisciplinary collaboration between behavioral scientists and engineers.

  6. Neuronal factors determining high intelligence.

    Science.gov (United States)

    Dicke, Ursula; Roth, Gerhard

    2016-01-05

    Many attempts have been made to correlate degrees of both animal and human intelligence with brain properties. With respect to mammals, a much-discussed trait concerns absolute and relative brain size, either uncorrected or corrected for body size. However, the correlation of both with degrees of intelligence yields large inconsistencies, because although they are regarded as the most intelligent mammals, monkeys and apes, including humans, have neither the absolutely nor the relatively largest brains. The best fit between brain traits and degrees of intelligence among mammals is reached by a combination of the number of cortical neurons, neuron packing density, interneuronal distance and axonal conduction velocity--factors that determine general information processing capacity (IPC), as reflected by general intelligence. The highest IPC is found in humans, followed by the great apes, Old World and New World monkeys. The IPC of cetaceans and elephants is much lower because of a thin cortex, low neuron packing density and low axonal conduction velocity. By contrast, corvid and psittacid birds have very small and densely packed pallial neurons and relatively many neurons, which, despite very small brain volumes, might explain their high intelligence. The evolution of a syntactical and grammatical language in humans most probably has served as an additional intelligence amplifier, which may have happened in songbirds and psittacids in a convergent manner. © 2015 The Author(s).

  7. Intelligence in children

    Directory of Open Access Journals (Sweden)

    Martín Nader

    2015-09-01

    Full Text Available Partial results of an investigation are presented whose primary objective is to adapt and to standardize the neurocognitive assessment battery C.A.S. of Das and Naglieri (1997 in a child sample. The test is an operationalization of a non traditional intelligence model (PASS that considers the intelligent behaviors as a group of four cognitive basic processes (planning, attention, simultaneous and successive processing. The objectives of this work are to obtain the psychometric properties of the instrument and also, to analyze if differences exist according to sex and age. The study type is crosswise - transactional. It was administered the CAS to 150 children residents in Buenos Aires among the ages of 6 to 12 years (population general non consultant and the WISC-III to a sample of 50 children. 

  8. Intelligent Design and Intelligent Failure

    Science.gov (United States)

    Jerman, Gregory

    2015-01-01

    Good Evening, my name is Greg Jerman and for nearly a quarter century I have been performing failure analysis on NASA's aerospace hardware. During that time I had the distinct privilege of keeping the Space Shuttle flying for two thirds of its history. I have analyzed a wide variety of failed hardware from simple electrical cables to cryogenic fuel tanks to high temperature turbine blades. During this time I have found that for all the time we spend intelligently designing things, we need to be equally intelligent about understanding why things fail. The NASA Flight Director for Apollo 13, Gene Kranz, is best known for the expression "Failure is not an option." However, NASA history is filled with failures both large and small, so it might be more accurate to say failure is inevitable. It is how we react and learn from our failures that makes the difference.

  9. Intelligent structural optimization: Concept, Model and Methods

    International Nuclear Information System (INIS)

    Lu, Dagang; Wang, Guangyuan; Peng, Zhang

    2002-01-01

    Structural optimization has many characteristics of Soft Design, and so, it is necessary to apply the experience of human experts to solving the uncertain and multidisciplinary optimization problems in large-scale and complex engineering systems. With the development of artificial intelligence (AI) and computational intelligence (CI), the theory of structural optimization is now developing into the direction of intelligent optimization. In this paper, a concept of Intelligent Structural Optimization (ISO) is proposed. And then, a design process model of ISO is put forward in which each design sub-process model are discussed. Finally, the design methods of ISO are presented

  10. Development and Flight Results of a PC104/QNX-Based On-Board Computer and Software for the YES2 Tether Experiment

    Science.gov (United States)

    Spiliotopoulos, I.; Mirmont, M.; Kruijff, M.

    2008-08-01

    This paper highlights the flight preparation and mission performance of a PC104-based On-Board Computer for ESA's second Young Engineer's Satellite (YES2), with additional attention to the flight software design and experience of QNX as multi-process real-time operating system. This combination of Commercial-Of-The-Shelf (COTS) technologies is an accessible option for small satellites with high computational demands.

  11. An independent confirmatory factor analysis of the Wechsler Intelligence Scale for Children-fourth Edition (WISC-IV) integrated: what do the process approach subtests measure?

    Science.gov (United States)

    Benson, Nicholas; Hulac, David M; Bernstein, Joshua D

    2013-09-01

    The Wechsler intelligence scale for children--fourth edition (WISC-IV) Integrated contains the WISC-IV core and supplemental subtests along with process approach subtests designed to facilitate a process-oriented approach to score interpretation. The purpose of this study was to examine the extent to which WISC-IV Integrated subtests measure the constructs they are purported to measure. In addition to examining the measurement and scoring model provided in the manual, this study also tested hypotheses regarding Cattell-Horn-Carroll abilities that might be measured along with other substantive questions regarding the factor structure of the WISC-IV Integrated and the nature of abilities measured by process approach subtests. Results provide insight regarding the constructs measured by these subtests. Many subtests appear to be good to excellent measures of psychometric g (i.e., the general factor presumed to cause the positive correlation of mental tasks). Other abilities measured by subtests are described. For some subtests, the majority of variance is not accounted for by theoretical constructs included in the scoring model. Modifications made to remove demands such as memory recall and verbal expression were found to reduce construct-irrelevant variance. The WISC-IV Integrated subtests appear to measure similar constructs across ages 6-16, although strict factorial invariance was not supported.

  12. Development of an on-board H2 storage and recovery system based on lithium borohydride.

    Science.gov (United States)

    2014-02-28

    Alkali metal borohydrides based on sodium and lithium, NaBH4 and LiBH4, have been evaluated as a potential hydrogen storage and recovery system for on-board vehicle use. The borohydride salts could be dissolved in water, followed by a hydrolytic reac...

  13. On-board conversion of methanol to dimethyl ether as an alternative diesel fuel

    Energy Technology Data Exchange (ETDEWEB)

    Armbruster, H; Heinzelmann, G; Struis, R; Stucki, S [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    1999-08-01

    The catalytic dehydration of methanol to dimethyl ether was investigated for application on-board a methanol fuelled vehicle. Several catalysts have been tested in a fixed bed reactor. Our approach is to develop a small and efficient reactor converting liquid MeOH under pressure and at low reaction temperatures. (author) 2 figs., 5 refs.

  14. Lifestyle factors in Croatian seafarers as relating to health and stress on board.

    Science.gov (United States)

    Slišković, Ana; Penezić, Zvjezdan

    2017-01-01

    Seafaring is characterized by specific stressors and health risks. The purpose of this article was to compare the prevalence of various lifestyle factors between the shipping and home environments, and in addition to test the relations between lifestyle factors, perceived stress on board, and health in seafarers. A total of 530 Croatian seafarers participated in an on-line survey. The questionnaire contained requests for demographic data and a set of questions relating to lifestyle, stress on board, physical health symptoms, and mental health. The data showed higher sleep deprivation, higher levels of smoking and unhealthier diet at sea than at home, with prevalence of alcohol consumption and physical exercise being more favourable for the shipping environment. Sleep deprivation, unhealthy diet, lack of physical exercise, and smoking are shown as negative correlates of various measures of health. Stress on board was associated with sleep deprivation and unhealthy diet, and with more unfavourable physical and mental health. The results give practical implications for promoting health in seafarers. Some of the lifestyle factors tested, such as alcohol use, smoking and physical exercise, fall rather under individual control, but others, such as a healthy, balanced diet on board and sleeping hygiene at sea, should be improved by shipping management.

  15. 40 CFR 85.2222 - On-board diagnostic test procedures.

    Science.gov (United States)

    2010-07-01

    ... on-board diagnostic systems on 1996 and newer light-duty vehicles and light-duty trucks shall consist... the unset readiness code(s) in question may be issued a passing certificate without being required to... lit malfunction indicator light (MIL) must be failed, though setting the unset readiness flags in...

  16. Influence of on-board irradiation on the shelflife of redfish

    International Nuclear Information System (INIS)

    Reinacher, E.; Ehlermann, D.

    1978-01-01

    Continuing former investigations during two voyages of the RV 'Anton Dohrn' redfish (Sebastes marinus) was irradiated on board and stored under different conditions, wrapped and unwrapped under melting ice. A part of the irradiated, unwrapped samples was stored under irradiated ice. As in the former investigations the irradiation treatment effected no prolongation of shelflife in the range of marketable quality. (orig.) [de

  17. Performance analysis of different organic Rankine cycle configurations on board liquefied natural gas-fuelled vessels

    DEFF Research Database (Denmark)

    Baldasso, Enrico; Andreasen, Jesper Graa; Meroni, Andrea

    2017-01-01

    Gas-fuelled shipping is expected to increase significantly in the coming years. Similarly, much effort is devoted to the study of waste heat recovery systems to be implemented on board ships. In this context, the organic Rankine cycle (ORC) technology is considered one of the most promising...

  18. THE DEVELOPMENT OF METHOD AND ON-BOARD DEVICES FOR COLLISION AVOIDANCE WHEN OVERTAKING

    Directory of Open Access Journals (Sweden)

    Podryhalo, M.

    2013-06-01

    Full Text Available A method for improving the safety of overtaking maneuver by using the on-board collision avoidance system, which has an increased assessment reliability of safety of vehicles overtaking that move in the same direction is offered. The proposed system takes into account the main factors that affect the overtaking maneuver.

  19. New technologies for fire suppression on board naval craft, FiST

    NARCIS (Netherlands)

    Rahm, M.; Hiltz, J.; Wal, R. van der; Hertzberg, T.; Lindström, J.

    2014-01-01

    For three years Canada, Sweden and the Netherlands have been investigating new technologies for fire suppression on board naval crafts within the FiST project. The project has focused on a number of technologies. These included the evaluation of water based fire suppression systems and in particular

  20. Accidents on board merchant ships. Suggestions based on Centro Internazionale Radio Medico (CIRM) experience.

    Science.gov (United States)

    Napoleone, Paolo

    2016-01-01

    This statistical study was performed to find out the occurrence of accidents on board ships assisted by Centro Internazionale Radio Medico (CIRM) during the years 2010-2015, with the aim of providing suggestions in accident prevention, based on such a wide experience. The case histories of CIRM in the years 2010-2015 were examined. The total number of accidents per year was calculated and compared as a percentage with the total number of cases assisted by CIRM per year. The incidence of accidents on board in these years ranged between 14.4% and 18.4% of total cases assisted per year, which is constantly increasing. The most common injuries on board among cases treated by CIRM were contusions and wounds. Also burns and eye injuries were significantly represented. Multiple injuries and head injuries were found to be the most frequent cause of death on board due to an accident. More information on the occurrence and type of accidents and on the body injured areas should represent the basis for developing strategies and campaigns for their prevention.

  1. CALIBRATION OF MODIFIED LIULIN DETECTOR FOR COSMIC RADIATION MEASUREMENTS ON-BOARD AIRCRAFT

    Czech Academy of Sciences Publication Activity Database

    Kyselová, Dagmar; Ambrožová, Iva; Krist, Pavel; Kubančák, Ján; Uchihori, Y.; Kitamura, H.; Ploc, Ondřej

    2015-01-01

    Roč. 164, č. 4 (2015), s. 489-492 ISSN 0144-8420 R&D Projects: GA MŠk(CZ) LG13031 Institutional support: RVO:61389005 Keywords : Liulin detector * on-board aircraft * cosmic radiation measurement Subject RIV: BG - Nuclear, Atomic and Molecular Physics, Colliders Impact factor: 0.894, year: 2015

  2. Validation of multi-channel scanning microwave radiometer on-board Oceansat-1

    Digital Repository Service at National Institute of Oceanography (India)

    Muraleedharan, P.M.; Pankajakshan, T.; Harikrishnan, M.

    Sea surface temperature (SST), sea surface wind speed (WS) and columnar water vapour (WV) derived from Multi-frequency Scanning Microwave Radiometer (MSMR) sensor on-board IRS-P4 (Oceansat-1) were validated against the in situ measurements from ship...

  3. AGB Statement on Board Responsibility for the Oversight of Educational Quality

    Science.gov (United States)

    Association of Governing Boards of Universities and Colleges, 2011

    2011-01-01

    This "Statement on Board Responsibility for the Oversight of Educational Quality," approved by the Board of Directors of the Association of Governing Boards (AGB) in March 2011, urges institutional administrators and governing boards to engage fully in this area of board responsibility. The seven principles in this statement offer suggestions to…

  4. Towards human-oriented norms : Considering the effects of noise and vibration exposure on board ships

    NARCIS (Netherlands)

    Kurt, R.E.; Khalid, H.; Turan, O.; Houben, M.M.J.; Bos, J.E.; Helvacioglu, I.H.

    2016-01-01

    With modern trends of decrease in crew numbers on board ships together with increased operational demands and paperwork, crew fatigue and comfort have become more critical and are being given more importance. It is well known that environmental factors affect crew comfort and performance. The two

  5. Survivability of chilled water networks on board ships when using dincs

    NARCIS (Netherlands)

    Smit, C.S.

    2012-01-01

    Fast reaction is required when a chilled water distribution network on board a naval ship is damaged. Without immediate isolation of the leakage area, all water supply is lost soon, with immense consequences for the ship’s operational state. The only solution for that is using an automated recovery

  6. Towards human-oriented norms: Considering the effects of noise exposure on board ships

    NARCIS (Netherlands)

    Kurt, R.E.; Khalid, H.; Turan, O.; Houben, M.; Bos, J.; Helvacioglu, I.H.

    2016-01-01

    With modern trends of decrease in crew numbers on board ships together with increased operational demands and paperwork, crew fatigue and comfort have become more critical and are being given more importance. It is well known that environmental factors affect crew comfort and performance. The two

  7. Atlantic mackerel and Horse mackerel egg survey 2016: Dutch participation on board FV Atlantic Lady: May

    NARCIS (Netherlands)

    Damme, van C.J.G.

    2016-01-01

    From 10 till 25 May 2016 IMARES carried out a mackerel and horse mackerel egg survey on board the FV Atlantic Lady. This survey was part of the international mackerel and horse mackerel egg survey coordinated by ICES. The Redersvereniging voor de Zeevisserij (RVZ) asked IMARES to carry out this

  8. WE-AB-303-09: Rapid Projection Computations for On-Board Digital Tomosynthesis in Radiation Therapy

    International Nuclear Information System (INIS)

    Iliopoulos, AS; Sun, X; Pitsianis, N; Yin, FF; Ren, L

    2015-01-01

    Purpose: To facilitate fast and accurate iterative volumetric image reconstruction from limited-angle on-board projections. Methods: Intrafraction motion hinders the clinical applicability of modern radiotherapy techniques, such as lung stereotactic body radiation therapy (SBRT). The LIVE system may impact clinical practice by recovering volumetric information via Digital Tomosynthesis (DTS), thus entailing low time and radiation dose for image acquisition during treatment. The DTS is estimated as a deformation of prior CT via iterative registration with on-board images; this shifts the challenge to the computational domain, owing largely to repeated projection computations across iterations. We address this issue by composing efficient digital projection operators from their constituent parts. This allows us to separate the static (projection geometry) and dynamic (volume/image data) parts of projection operations by means of pre-computations, enabling fast on-board processing, while also relaxing constraints on underlying numerical models (e.g. regridding interpolation kernels). Further decoupling the projectors into simpler ones ensures the incurred memory overhead remains low, within the capacity of a single GPU. These operators depend only on the treatment plan and may be reused across iterations and patients. The dynamic processing load is kept to a minimum and maps well to the GPU computational model. Results: We have integrated efficient, pre-computable modules for volumetric ray-casting and FDK-based back-projection with the LIVE processing pipeline. Our results show a 60x acceleration of the DTS computations, compared to the previous version, using a single GPU; presently, reconstruction is attained within a couple of minutes. The present implementation allows for significant flexibility in terms of the numerical and operational projection model; we are investigating the benefit of further optimizations and accurate digital projection sub

  9. WE-AB-303-09: Rapid Projection Computations for On-Board Digital Tomosynthesis in Radiation Therapy

    Energy Technology Data Exchange (ETDEWEB)

    Iliopoulos, AS; Sun, X [Duke University, Durham, NC (United States); Pitsianis, N [Aristotle University of Thessaloniki (Greece); Duke University, Durham, NC (United States); Yin, FF; Ren, L [Duke University Medical Center, Durham, NC (United States)

    2015-06-15

    Purpose: To facilitate fast and accurate iterative volumetric image reconstruction from limited-angle on-board projections. Methods: Intrafraction motion hinders the clinical applicability of modern radiotherapy techniques, such as lung stereotactic body radiation therapy (SBRT). The LIVE system may impact clinical practice by recovering volumetric information via Digital Tomosynthesis (DTS), thus entailing low time and radiation dose for image acquisition during treatment. The DTS is estimated as a deformation of prior CT via iterative registration with on-board images; this shifts the challenge to the computational domain, owing largely to repeated projection computations across iterations. We address this issue by composing efficient digital projection operators from their constituent parts. This allows us to separate the static (projection geometry) and dynamic (volume/image data) parts of projection operations by means of pre-computations, enabling fast on-board processing, while also relaxing constraints on underlying numerical models (e.g. regridding interpolation kernels). Further decoupling the projectors into simpler ones ensures the incurred memory overhead remains low, within the capacity of a single GPU. These operators depend only on the treatment plan and may be reused across iterations and patients. The dynamic processing load is kept to a minimum and maps well to the GPU computational model. Results: We have integrated efficient, pre-computable modules for volumetric ray-casting and FDK-based back-projection with the LIVE processing pipeline. Our results show a 60x acceleration of the DTS computations, compared to the previous version, using a single GPU; presently, reconstruction is attained within a couple of minutes. The present implementation allows for significant flexibility in terms of the numerical and operational projection model; we are investigating the benefit of further optimizations and accurate digital projection sub

  10. System for intelligent teleoperation research

    International Nuclear Information System (INIS)

    Orlando, N.E.

    1983-01-01

    The Automation Technology Branch of NASA Langley Research Center is developing a research capability in the field of artificial intelligence, particularly as applicable in teleoperator/robotics development for remote space operations. As a testbed for experimentation in these areas, a system concept has been developed and is being implemented. This system, termed DAISIE (Distributed Artificially Intelligent System for Interacting with the Environment), interfaces the key processes of perception, reasoning, and manipulation by linking hardware sensors and manipulators to a modular artificial intelligence (AI) software system in a hierarchical control structure. Verification experiments have been performed: one experiment used a blocksworld database and planner embedded in the DAISIE system to intelligently manipulate a simple physical environment; the other experiment implemented a joint-space collision avoidance algorithm. Continued system development is planned

  11. Intelligent instrumentation principles and applications

    CERN Document Server

    Bhuyan, Manabendra

    2011-01-01

    With the advent of microprocessors and digital-processing technologies as catalyst, classical sensors capable of simple signal conditioning operations have evolved rapidly to take on higher and more specialized functions including validation, compensation, and classification. This new category of sensor expands the scope of incorporating intelligence into instrumentation systems, yet with such rapid changes, there has developed no universal standard for design, definition, or requirement with which to unify intelligent instrumentation. Explaining the underlying design methodologies of intelligent instrumentation, Intelligent Instrumentation: Principles and Applications provides a comprehensive and authoritative resource on the scientific foundations from which to coordinate and advance the field. Employing a textbook-like language, this book translates methodologies to more than 80 numerical examples, and provides applications in 14 case studies for a complete and working understanding of the material. Beginn...

  12. Identity development, intelligence structure, and interests: a cross-sectional study in a group of Italian adolescents during the decision-making process

    Directory of Open Access Journals (Sweden)

    Pellerone M

    2015-08-01

    Full Text Available Monica Pellerone,1 Alessia Passanisi,1 Mario Filippo Paolo Bellomo2 1Faculty of Human and Social Science, “Kore” University of Enna, Enna, 2Credito Emiliano Bank, Piazza Armerina, Italy Background: Forming one’s identity is thought to be the key developmental task of adolescence, but profound changes in personality traits also occur in this period. The negotiation of complex social settings, the creation of an integrated identity, and career choice are major tasks of adolescence. The adolescent, having to make choices for his or her future, has not only to consider his or her own aspirations and interests but also to possess a capacity for exploration and commitment; in fact, career commitments can be considered as a fit between the study or career that is chosen and personal values, skills, and preferences. Methods: The objective of the study reported here was to investigate the role of identity on profile of interests; the relation between identity and decisional style; the correlation between identity, aptitudes, interests, and school performance; and the predictive variables to school success. The research involved 417 Italian students who live in Enna, a small city located in Sicily, Italy, aged 16–19 years (197 males and 220 females in the fourth year (mean =17.2, standard deviation =0.52 and the fifth year (mean =18.2, standard deviation =0.64 of senior secondary school. The research lasted for one school year; the general group of participants consisted of 470 students, and although all participants agreed to be part of the research, there was a dropout rate of 11.28%. They completed the Ego Identity Process Questionnaire to measure their identity development, the Intelligence Structure Test to investigate aptitudes, the Self-Directed Search to value interests, and General Decision Making Style questionnaire to describe their individual decisional style. Results: The data showed that high-school performance was positively

  13. MICROBIOLOGICAL EFFECTS OF ON-BOARD FISHING VESSEL HANDLING IN MERLUCCIUS MERLUCCIUS

    Directory of Open Access Journals (Sweden)

    P. Serratore

    2011-01-01

    Full Text Available The purpose of the present study was to determine the impact of different manipulation techniques applied on board fishing vessel, on the microbiological quality of the flesh of European hake (Merluccius merluccius during storage at +3°C ± 1°C for a time (T of 10 days after landing (T1-T10. Samples of fish were taken from a fishing vessel of the Adriatic Sea and from one of the Tyrrhenian Sea, treated on-board under different icing conditions: 1 a low ice/product weight ratio and 2 an optimal ice/product weight ratio, up to 1:3 (3. Spoilage bacteria as Total Bacterial Count (TBC and specific spoilage bacteria as Sulphide Producing Bacteria (SPB were enumerated in fish flesh as Colony Forming Units (CFU/g on Plate Count Agar and Lyngby Agar at 20°C for 3-5 days. TBC of the Adriatic fishes (gutted on-board resulted 103 UFC/g at T1-T6, and 104-105 at T10, whereas TBC of the Tyrrhenian fishes (not gutted on-board resulted 10-102 UFC/g at T2- T3, 103 at T6, and 104-105 at T10. SPB resulted 10- 102 UFC/g at T1-T6, and 103- 104 at T10, with absolute values higher in the Adriatic fishes, in respect with the Tyrrhenian fishes, and in the low icing conditions in respect with the optimal icing condition. At the experimented condition, the lowering of the microbiological quality of fish flesh during storage, seems to be more dependent on the gutting versus not gutting on-board practice rather than on the low versus optimal icing treatment.

  14. Integrating RFID Technology and EPC Network into a B2B Retail Supply Chain: A Step Toward Intelligent Business Processes

    Directory of Open Access Journals (Sweden)

    Samuel Fosso Wamba

    2007-06-01

    Full Text Available This article introduces RFID technology and the EPC Network and investigates their potential for B-to-B eCommerce supply chain management. Based on empirical data gathered from four tightly interrelated firms from three layers of a supply chain, several scenarios integrating RFID and the EPC Network have been tested and evaluated. In the context of warehousing activities in one specific retail supply chain, the results indicate that i the business process approach seems quite appropriate to capture the real potential of RFID and the EPC Network; ii RFID technology and the EPC Network can improve the “shipping” and the “receiving” processes; iii they can automatically trigger some business processes; iv they foster a higher level of information sharing between supply chain members; and v they promote the emergence of new business processes such as “process-to-process,” “process-to-machine,” and “machine-to-machine.” The paper helps to improve our understanding of the real potential of RFID and the EPC Network for business processes.

  15. GPS and Galileo Developments on Board the International Space Station With the Space Communications and Navigation (SCaN) Testbed

    Science.gov (United States)

    Pozzobon, Oscar; Fantinato, Samuele; Dalla Chiara, Andrea; Gamba, Giovanni; Crisci, Massimo; Giordana, Pietro; Enderle, Werner; Chelmins, David; Sands, Obed S.; Clapper, Carolyn J.; hide

    2016-01-01

    The Space Communications and Navigation (SCaN) is a facility developed by NASA and hosted on board the International Space Station (ISS) on an external truss since 2013.It has the objective of testing navigation and communication experimentations with a Software Defined Radio (SDR) approach, which permits software updates for testing new experimentations.NASA has developed the Space Telecommunications Radio System (STRS) architecture standard for SDRs used in space and ground-based platforms to provide commonality among radio developments to provide enhanced capability. The hardware is equipped with both L band front-end radios and the NASA space network communicates with it using S-band, Ku-band and Ka-band links.In May 2016 Qascom started GARISS (GPS and Galileo Receiver for the ISS), an activity of experimentation in collaboration with ESA and NASA that has the objective to develop and validate the acquisition and processing of combined GPS and Galileo signals on board the ISS SCaN testbed. This paper has the objective to present the mission, and provide preliminary details about the challenges in the design, development and verification of the waveform that will be installed on equipment with limited resources. GARISS is also the first attempt to develop a waveform for the ISS as part of an international collaboration between US and Europe. Although the final mission objective is to target dual frequency processing, initial operations will foresee a single frequency processing. Initial results and trade-off between the two options, as well as the final decision will be presented and discussed. The limited resources on board the SCaN with respect to the challenging requirements to acquire and track contemporaneously two satellite navigation systems, with different modulations and data structure, led to the need to assess the possibility of aiding from ground through the S-band. This option would allow assistance to the space receiver in order to provide

  16. Simulation based on intelligent agents of the process of negotiation of the electric power market in Colombia

    International Nuclear Information System (INIS)

    Pastrana David, Maria Marcela; Guzman Luna, Jaime A; Ovalle Carranza, Demetrio Arturo

    2005-01-01

    The aim of this paper is describing the phases of analyzing, designing, building and validation of a multi-agent system to simulate the negotiation process of Colombian electric energy market. This project intent to exhibit advantages of multi-agent systems to model simulation processes. Analysis and design phases use MAS-common KADS rnethodology, which is one of the well known for agent-based system modeling. For this purpose, it is modeled the part of negotiation process among market human agents, which is representing by energy buying and selling among energy generators, commercial agents, and consumers

  17. Patterns and Intelligent Systems

    International Nuclear Information System (INIS)

    Cordes, Gail A.

    2003-01-01

    The recognition and analysis of evolving patterns provides a unifying concept for studying and implementing intelligent information processing for open feedback control systems within the nuclear industry. Control is considered as influence of a large system to achieve the goals of the human (who might or might not be part of an open feedback loop) and is not limited to operation of a component within a nuclear power plant. The intelligent control system includes open logic and can automatically react to new data in an unprogrammed way. This application of evolving patterns integrates current research developments in human cognition and scientific semiotics with traditional feedback control. A preliminary implementation of such a system using existing computational techniques is postulated, and tools that are lacking at this time are identified. Proof-of-concept applications for the nuclear industry are referenced

  18. Fostering collective intelligence education

    Directory of Open Access Journals (Sweden)

    Jaime Meza

    2016-06-01

    Full Text Available New educational models are necessary to update learning environments to the digitally shared communication and information. Collective intelligence is an emerging field that already has a significant impact in many areas and will have great implications in education, not only from the side of new methodologies but also as a challenge for education. This paper proposes an approach to a collective intelligence model of teaching using Internet to combine two strategies: idea management and real time assessment in the class. A digital tool named Fabricius has been created supporting these two elements to foster the collaboration and engagement of students in the learning process. As a result of the research we propose a list of KPI trying to measure individual and collective performance. We are conscious that this is just a first approach to define which aspects of a class following a course can be qualified and quantified.

  19. Business Intelligence

    OpenAIRE

    Petersen, Anders

    2001-01-01

    Cílem této bakalářské práce je seznámení s Business Intelligence a zpracování vývojového trendu, který ovlivňuje podobu řešení Business Intelligence v podniku ? Business Activity Monitoring. Pro zpracování tohoto tématu byla použita metoda studia odborných pramenů, a to jak v českém, tak v anglickém jazyce. Hlavním přínosem práce je ucelený, v českém jazyce zpracovaný materiál pojednávající o Business Activity Monitoring. Práce je rozdělena do šesti hlavních kapitol. Prvních pět je věnováno p...

  20. Web Intelligence and Artificial Intelligence in Education

    Science.gov (United States)

    Devedzic, Vladan

    2004-01-01

    This paper surveys important aspects of Web Intelligence (WI) in the context of Artificial Intelligence in Education (AIED) research. WI explores the fundamental roles as well as practical impacts of Artificial Intelligence (AI) and advanced Information Technology (IT) on the next generation of Web-related products, systems, services, and…