Impact Analysis for Fuel Assemblies in Spent Fuel Storage Rack

International Nuclear Information System (INIS)

Oh, Jinho

2013-01-01

The design and structural integrity evaluation of a spent fuel storage rack (SFSR) utilized for storing and protecting the spent fuel assemblies generated during the operation of a reactor are very important in terms of nuclear safety and waste management. The objective of this study is to show the validity of the SFSR design as well as fuel assembly through a structural integrity evaluation based on a numerical analysis. In particular, a dynamic time history analysis considering the gaps between the fuel assemblies and the walls of the storage cell pipes in the SFSR was performed to check the structural integrity of the fuel assembly and storage cell pipe

Impact Analysis for Fuel Assemblies in Spent Fuel Storage Rack

Energy Technology Data Exchange (ETDEWEB)

Oh, Jinho [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2013-07-01

The design and structural integrity evaluation of a spent fuel storage rack (SFSR) utilized for storing and protecting the spent fuel assemblies generated during the operation of a reactor are very important in terms of nuclear safety and waste management. The objective of this study is to show the validity of the SFSR design as well as fuel assembly through a structural integrity evaluation based on a numerical analysis. In particular, a dynamic time history analysis considering the gaps between the fuel assemblies and the walls of the storage cell pipes in the SFSR was performed to check the structural integrity of the fuel assembly and storage cell pipe.

Comment on id-based remote data integrity checking with data privacy preserving

Science.gov (United States)

Zhang, Jianhong; Meng, Hongxin

2017-09-01

Recently, an ID-based remote data integrity checking protocol with perfect data privacy preserving (IEEE Transactions on Information Forensics and Security, doi: 10.1109/TIFS.2016.2615853) was proposed to achieve data privacy protection and integrity checking. Unfortunately, in this letter, we demonstrate that their protocol is insecure. An active hacker can modify the stored data without being detected by the verifier in the auditing. And we also show malicious cloud server can convince the verifier that the stored data are kept intact after the outsourced data blocks are deleted. Finally, the reasons to produce such attacks are given.

Stability check source measurements with a secondary standard dosimeter in SSDL-Pakistan

International Nuclear Information System (INIS)

Salman, S.; Mahmoud, K.; Orfi, S.D.

1988-01-01

The stability check source is an integral part of a Secondary Standard Dosimetry System. The purpose of the stability check source is to confirm that the overall response of the dosimeter has not changed significantly since the instrument was calibrated. In case any change in the sensitivity of the ionization chamber or measuring assembly occurs the same is reflected in the reference check source measurements. Stability check source measurements are taken in a Primary Standard Dosimetry Laboratory (PSDL) at the time of calibration of secondary standard dosimeter and mean time (in seconds) to the reference setting of 50 scale divisions with ambient conditions of air at 20 deg. C, 101.3 kPa and 50% RH is quoted in a calibration certificate. This quoted stability check source time figure is the basis for future confirmation of overall response of the secondary standard dosimeter system. This note presents the results of stability check source measurements carried out in SSDL Pakistan over a period of five years

The NIRspec assembly integration and test status

Science.gov (United States)

Wettemann, Thomas; Ehrenwinkler, Ralf; Johnson, Thomas E.; Maschmann, Marc; Mosner, Peter; te Plate, Maurice; Rödel, Andreas

2017-11-01

The Near-Infrared Spectrograph (NIRSpec) is one of the four instruments on the James Webb Space Telescope (JWST) scheduled for launch in 2018. NIRSpec has been manufactured and tested by an European industrial consortium led by Airbus Defence and Space and delivered to the European Space Agency (ESA) and NASA in September 2013. Since then it has successfully been integrated into the JWST Integrated Science Instrument Module (ISIM) and is currently in ISIM Cryo-Vacuum Test#2. Since however two of its most important assemblies, the Focal Plane Assembly (FPA) and the Micro-Shutter Assembly (MSA) need to be replaced by new units we will present the status of the instrument, the status of its new flight assemblies in manufacturing and testing and give an outlook on the planned exchange activities and the following instrument re-verification.

Integrity Checking and Maintenance with Active Rules in XML Databases

DEFF Research Database (Denmark)

Christiansen, Henning; Rekouts, Maria

2007-01-01

While specification languages for integrity constraints for XML data have been considered in the literature, actual technologies and methodologies for checking and maintaining integrity are still in their infancy. Triggers, or active rules, which are widely used in previous technologies for the p...... updates, the method indicates trigger conditions and correctness criteria to be met by the trigger code supplied by a developer or possibly automatic methods. We show examples developed in the Sedna XML database system which provides a running implementation of XML triggers....

Integrating model checking with HiP-HOPS in model-based safety analysis

International Nuclear Information System (INIS)

Sharvia, Septavera; Papadopoulos, Yiannis

2015-01-01

The ability to perform an effective and robust safety analysis on the design of modern safety–critical systems is crucial. Model-based safety analysis (MBSA) has been introduced in recent years to support the assessment of complex system design by focusing on the system model as the central artefact, and by automating the synthesis and analysis of failure-extended models. Model checking and failure logic synthesis and analysis (FLSA) are two prominent MBSA paradigms. Extensive research has placed emphasis on the development of these techniques, but discussion on their integration remains limited. In this paper, we propose a technique in which model checking and Hierarchically Performed Hazard Origin and Propagation Studies (HiP-HOPS) – an advanced FLSA technique – can be applied synergistically with benefit for the MBSA process. The application of the technique is illustrated through an example of a brake-by-wire system. - Highlights: • We propose technique to integrate HiP-HOPS and model checking. • State machines can be systematically constructed from HiP-HOPS. • The strengths of different MBSA techniques are combined. • Demonstrated through modeling and analysis of brake-by-wire system. • Root cause analysis is automated and system dynamic behaviors analyzed and verified

Integrating succession and community assembly perspectives.

Science.gov (United States)

Chang, Cynthia; HilleRisLambers, Janneke

2016-01-01

Succession and community assembly research overlap in many respects, such as through their focus on how ecological processes like dispersal, environmental filters, and biotic interactions influence community structure. Indeed, many recent advances have been made by successional studies that draw on modern analytical techniques introduced by contemporary community assembly studies. However, community assembly studies generally lack a temporal perspective, both on how the forces structuring communities might change over time and on how historical contingency (e.g. priority effects and legacy effects) and complex transitions (e.g. threshold effects) might alter community trajectories. We believe a full understanding of the complex interacting processes that shape community dynamics across large temporal scales can best be achieved by combining concepts, tools, and study systems into an integrated conceptual framework that draws upon both succession and community assembly theory.

Ergonomic risk assessment with DesignCheck to evaluate assembly work in different phases of the vehicle development process.

Science.gov (United States)

Winter, Gabriele; Schaub, Karlheinz G; Großmann, Kay; Laun, Gerhard; Landau, Kurt; Bruder, Ralph

2012-01-01

Occupational hazards exist, if the design of the work situation is not in accordance with ergonomic design principles. At assembly lines ergonomics is applied to the design of work equipment and tasks and to work organisation. The ignoring of ergonomic principles in planning and design of assembly work leads to unfavourable working posture, action force and material handling. Disorders of the musculoskeletal system are of a common occurrence throughout Europe. Musculoskeletal disorders are a challenge against the background of disabled workers. The changes in a worker's capability have to be regarded in the conception of redesigned and new assembly lines. In this way ergonomics becomes progressively more important in planning and design of vehicles: The objective of ergonomic design in different stages of the vehicles development process is to achieve an optimal adaptation of the assembly work to workers. Hence the ergonomic screening tool "Design Check" (DC) was developed to identify ergonomic deficits in workplace layouts. The screening-tool is based on the current ergonomic state of the art in the design of physical work and relevant EU legal requirements. It was tested within a federal German research project at selected work stations at the assembly lines at Dr.-Ing. h.c. F. Porsche AG / Stuttgart. Meanwhile the application of the screening-tool DC is transferred in other parts of the Porsche AG, Stuttgart. It is also realized as an ergonomic standard method to perform assembly work in different phases of the vehicle development process.

Ball check valve

International Nuclear Information System (INIS)

Bevilacqua, F.

1978-01-01

A pressurized nuclear reactor having an instrument assembly sheathed in a metallic tube which is extended vertically upward into the reactor core by traversing a metallic guide tube which is welded to the wall of the vessel is described. Sensors in each instrument assembly are connected to instruments outside the vessel to manifest the conditions within the core. Each instrument assembly probe is moved into position within a metallic guide channel. The guide channel penetrates the wall of the vessel and forms part of the barrier to the environment within the pressure vessel. Each channel includes a ball check valve which is opened by the instrument assembly probe when the probe passes through the valve. A ball valve element is moved from its seat by the probe to a position lateral of the bore of the channel and is guided to its seat along a sloped path within the valve body when the probe is removed. 5 claims, 3 figures

Integrating DNA strand-displacement circuitry with DNA tile self-assembly

Science.gov (United States)

Zhang, David Yu; Hariadi, Rizal F.; Choi, Harry M.T.; Winfree, Erik

2013-01-01

DNA nanotechnology has emerged as a reliable and programmable way of controlling matter at the nanoscale through the specificity of Watson–Crick base pairing, allowing both complex self-assembled structures with nanometer precision and complex reaction networks implementing digital and analog behaviors. Here we show how two well-developed frameworks, DNA tile self-assembly and DNA strand-displacement circuits, can be systematically integrated to provide programmable kinetic control of self-assembly. We demonstrate the triggered and catalytic isothermal self-assembly of DNA nanotubes over 10 μm long from precursor DNA double-crossover tiles activated by an upstream DNA catalyst network. Integrating more sophisticated control circuits and tile systems could enable precise spatial and temporal organization of dynamic molecular structures. PMID:23756381

Integral measurements on Caliban and Prospero assemblies for nuclear data validation; Mesures integrales sur les assemblages Caliban et Prospero pour la validation des donnees nucleaires

Energy Technology Data Exchange (ETDEWEB)

Casoli, P.; Authier, N.; Richard, B. [CEA Valduc, 21 - Is-sur-Tille (France); Ducauze-Philippe, M.; Cartier, J. [CEA Bruyeres-le-Chatel, 91 (France)

2011-07-15

How can the quality of nuclear data libraries be checked? Performing reference experiments also called benchmarks allows the testing of evaluated data. During these experiments, integral values such as reaction rates or neutron effective multiplication coefficients are measured. In this paper, the principles of benchmark construction are explained and illustrated with several works performed on the CALIBAN et PROSPERO critical assemblies operated by the Valduc center: benchmarks for dosimetry, activation reactions studies, neutron noise measurements. (authors)

WE-E-BRB-10: DosCheck - an Electronic Chart Checking Tool for Dosimetrists.

Science.gov (United States)

Yang, D; Wu, Y; Yaddanapudi, S; Moore, K; Pierbuxg, B; Brame, S; Mutic, S

2012-06-01

In addition to treatment planning, dosimetrists have to prepare documentation and manually enter data in treatment management system (TMS) which did not transfer or setup automatically. The required documents and data are dependent on the disease site, treatment machine and clinical workflow. Errors and inconsistencies can cause redundant work, treatment delays and potentially treatment errors. To address these issues, an electronic checking software tool, DosCheck was clinically implemented to check the existence of necessary documentations and the integrity of manually-entered data. The purpose of this software is to reduce the frequency of human errors and to improve efficiency. DosCheck reads data and documents from 1) TMS, 2) Pinnacle TPS, and 3) DICOM plan files stored in a DICOM-RT PACS. It processes documents in Word and PDF format, treatment plan data in Pinnacle native format and DICOM format, and Mosaiq data in database records. The software cross-checks data accuracy and consistency by following rules that are pre-defined according to the clinical requirements and treatment sties. It interacts with dosimetrists and presents instantaneous results via graphical user interface. DosCheck has been implemented in C#. It performs a full check for a patient with 20 seconds. It has been clinically commissioned and is used daily by all dosimetrists at our institution. Retrospective analysis shows that DosCheck identifies 30% to 40% of previously reported dosimetrist human errors. Additional ∼30% errors are checked by other tools that could be integrated DosCheck in the near future. As an electronic data checking tool, DosCheck can obtain and process data and documents from multiple clinical computer systems in the radiation oncology department, and perform checks according to clinical rules. It is able to improve the accuracy and efficiency of clinical data and document process, and therefore to reduce any potential inconsistencies and errors. © 2012 American

Cryogenic Fiber Optic Assemblies for Spaceflight Environments: Design, Manufacturing, Testing, and Integration

Science.gov (United States)

Thomes, W. Joe; Ott, Melanie N.; Chuska, Richard; Switzer, Robert; Onuma, Eleanya; Blair, Diana; Frese, Erich; Matyseck, Marc

2016-01-01

Fiber optic assemblies have been used on spaceflight missions for many years as an enabling technology for routing, transmitting, and detecting optical signals. Due to the overwhelming success of NASA in implementing fiber optic assemblies on spaceflight science-based instruments, system scientists increasingly request fibers that perform in extreme environments while still maintaining very high optical transmission, stability, and reliability. Many new applications require fiber optic assemblies that will operate down to cryogenic temperatures as low as 20 Kelvin. In order for the fiber assemblies to operate with little loss in optical throughput at these extreme temperatures requires a system level approach all the way from how the fiber assembly is manufactured to how it is held, routed, and integrated. The NASA Goddard Code 562 Photonics Group has been designing, manufacturing, testing, and integrating fiber optics for spaceflight and other high reliability applications for nearly 20 years. Design techniques and lessons learned over the years are consistently applied to developing new fiber optic assemblies that meet these demanding environments. System level trades, fiber assembly design methods, manufacturing, testing, and integration will be discussed. Specific recent examples of ground support equipment for the James Webb Space Telescope (JWST); the Ice, Cloud and Land Elevation Satellite-2 (ICESat-2); and others will be included.

Actinides integral measurements on FCA assemblies

International Nuclear Information System (INIS)

Mukaiyama, Takehiko; Okajima, Shigeaki

1984-01-01

Actinide integral measurements were performed on eight assemblies of FCA where neutron energy spectra were shifted systematically from soft to hard in order to evaluate and modify the nuclear cross section data of major actinides. Experimental values on actinide fission rates and sample reactivity worths are compared with the calculated values using JENDL-2 and ENDF/B-V (or IV) data sets. (author)

Localized synthesis, assembly and integration of silicon nanowires

Science.gov (United States)

Englander, Ongi

Localized synthesis, assembly and integration of one-dimensional silicon nanowires with MEMS structures is demonstrated and characterized in terms of local synthesis processes, electric-field assisted self-assembly, and a proof-of-concept nanoelectromechanical system (HEMS) demonstration. Emphasis is placed on the ease of integration, process control strategies, characterization techniques and the pursuit of integrated devices. A top-down followed by a bottom-up integration approach is utilized. Simple MEMS heater structures are utilized as the microscale platforms for the localized, bottom-up synthesis of one-dimensional nanostructures. Localized heating confines the high temperature region permitting only localized nanostructure synthesis and allowing the surroundings to remain at room temperature thus enabling CMOS compatible post-processing. The vapor-liquid-solid (VLS) process in the presence of a catalytic nanoparticle, a vapor phase reactant, and a specific temperature environment is successfully employed locally. Experimentally, a 5nm thick gold-palladium layer is used as the catalyst while silane is the vapor phase reactant. The current-voltage behavior of the MEMS structures can be correlated to the approximate temperature range required for the VLS reaction to take place. Silicon nanowires averaging 45nm in diameter and up to 29mum in length synthesized at growth rates of up to 1.5mum/min result. By placing two MEMS structures in close proximity, 4--10mum apart, localized silicon nanowire growth can be used to link together MEMS structures to yield a two-terminal, self-assembled micro-to-nano system. Here, one MEMS structure is designated as the hot growth structure while a nearby structure is designated as the cold secondary structure, whose role is to provide a natural stopping point for the VLS reaction. The application of a localized electric-field, 5 to 13V/mum in strength, during the synthesis process, has been shown to improve nanowire

The Assembly of the LHC Short Straight Sections (SSS) at CERN Project Status and Lessons Learned

CERN Document Server

Parma, Vittorio; Dos Santos de Campos, Paulo M; Feitor, Rogerio C; Gandel, Makcim; López, R; Schmidlkofer, Martin; Slits, Ivo

2005-01-01

The series production of the LHC SSS has started in the beginning of 2004 and is foreseen to last until end 2006. The production consists in the assembly of 474 cold masses housing superconducting quadrupoles and corrector magnets within their cryostats. 87 cold mass variants, resulting from various combinations of main quadrupole and corrector magnets, have to be assembled in 55 cryostat types, depending on the specific cryogenic and electrical powering schemes required by the collider topology. The assembly activity features the execution of more than 5 km of leak-tight welding of stainless steel and aluminium cryogenic lines, designed for 20-bar pressure, according to high qualification standards and undergoing severe QA inspections. Some 2500 leak detection tests, using He mass spectrometry, are required to check the tightness of the cryogenic circuits. Extensive electrical control work, to check the integrity of the magnet instrumentation and electrical circuits throughout the assembly of the SSS, is als...

Integration of Self-Assembled Microvascular Networks with Microfabricated PEG-Based Hydrogels.

Science.gov (United States)

Cuchiara, Michael P; Gould, Daniel J; McHale, Melissa K; Dickinson, Mary E; West, Jennifer L

2012-11-07

Despite tremendous efforts, tissue engineered constructs are restricted to thin, simple tissues sustained only by diffusion. The most significant barrier in tissue engineering is insufficient vascularization to deliver nutrients and metabolites during development in vitro and to facilitate rapid vascular integration in vivo. Tissue engineered constructs can be greatly improved by developing perfusable microvascular networks in vitro in order to provide transport that mimics native vascular organization and function. Here a microfluidic hydrogel is integrated with a self-assembling pro-vasculogenic co-culture in a strategy to perfuse microvascular networks in vitro. This approach allows for control over microvascular network self-assembly and employs an anastomotic interface for integration of self-assembled micro-vascular networks with fabricated microchannels. As a result, transport within the system shifts from simple diffusion to vessel supported convective transport and extra-vessel diffusion, thus improving overall mass transport properties. This work impacts the development of perfusable prevascularized tissues in vitro and ultimately tissue engineering applications in vivo.

Target Assembly to Check Boresight Alignment of Active Sensors

Science.gov (United States)

Ramos-Izquierdo, Luis; Scott, V. Stanley; Riris, Haris; Cavanaugh, John; Liiva, Peter; Rodriguez, Michael

2011-01-01

A compact and portable target assembly (Fig. 1) has been developed to measure the boresite alignment of LRO's Lunar Orbiter Laser Altimeter (LOLA) instrument at the spacecraft level. The concept for this target assembly has evolved over many years with earlier versions used to test the Mars Observer Laser Altimeter (MOLA), the Geoscience Laser Altimeter System (GLAS), and the Mercury Laser Altimeter (MLA) space-based instruments.

A Method for Model Checking Feature Interactions

DEFF Research Database (Denmark)

Pedersen, Thomas; Le Guilly, Thibaut; Ravn, Anders Peter

2015-01-01

This paper presents a method to check for feature interactions in a system assembled from independently developed concurrent processes as found in many reactive systems. The method combines and refines existing definitions and adds a set of activities. The activities describe how to populate the ...... the definitions with models to ensure that all interactions are captured. The method is illustrated on a home automation example with model checking as analysis tool. In particular, the modelling formalism is timed automata and the analysis uses UPPAAL to find interactions....

An Integrated Approach of Model checking and Temporal Fault Tree for System Safety Analysis

Energy Technology Data Exchange (ETDEWEB)

Koh, Kwang Yong; Seong, Poong Hyun [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of)

2009-10-15

Digitalization of instruments and control systems in nuclear power plants offers the potential to improve plant safety and reliability through features such as increased hardware reliability and stability, and improved failure detection capability. It however makes the systems and their safety analysis more complex. Originally, safety analysis was applied to hardware system components and formal methods mainly to software. For software-controlled or digitalized systems, it is necessary to integrate both. Fault tree analysis (FTA) which has been one of the most widely used safety analysis technique in nuclear industry suffers from several drawbacks as described in. In this work, to resolve the problems, FTA and model checking are integrated to provide formal, automated and qualitative assistance to informal and/or quantitative safety analysis. Our approach proposes to build a formal model of the system together with fault trees. We introduce several temporal gates based on timed computational tree logic (TCTL) to capture absolute time behaviors of the system and to give concrete semantics to fault tree gates to reduce errors during the analysis, and use model checking technique to automate the reasoning process of FTA.

Multispectral Thermal Imager Optical Assembly Performance and Integration of the Flight Focal Plane Assembly

International Nuclear Information System (INIS)

Blake, Dick; Byrd, Don; Christensen, Wynn; Henson, Tammy; Krumel, Les; Rappoport, William; Shen, Gon-Yen

1999-01-01

The Multispectral Thermal Imager Optical Assembly (OA) has been fabricated, assembled, successfully performance tested, and integrated into the flight payload structure with the flight Focal Plane Assembly (FPA) integrated and aligned to it. This represents a major milestone achieved towards completion of this earth observing E-O imaging sensor that is to be operated in low earth orbit. The OA consists of an off-axis three mirror anastigmatic (TMA) telescope with a 36 cm unobscured clear aperture, a wide-field-of-view (WFOV) of 1.82 along the direction of spacecraft motion and 1.38 across the direction of spacecraft motion. It also contains a comprehensive on-board radiometric calibration system. The OA is part of a multispectral pushbroom imaging sensor which employs a single mechanically cooled focal plane with 15 spectral bands covering a wavelength range from 0.45 to 10.7 m. The OA achieves near diffraction-limited performance from visible to the long-wave infrared (LWIR) wavelengths. The two major design drivers for the OA are 80% enpixeled energy in the visible bands and radiometric stability. Enpixeled energy in the visible bands also drove the alignment of the FPA detectors to the OA image plane to a requirement of less than 20 m over the entire visible detector field of view (FOV). Radiometric stability requirements mandated a cold Lyot stop for stray light rejection and thermal background reduction. The Lyot stop is part of the FPA assembly and acts as the aperture stop for the imaging system. The alignment of the Lyot stop to the OA drove the centering and to some extent the tilt alignment requirements of the FPA to the OA

Clean industrial room for drift tube assembling

International Nuclear Information System (INIS)

Glonti, G.L.; Gongadze, A.L.; Evtukhovich, P.G.

2001-01-01

Description of a clean industrial room for assembly of drift tubes for the muon spectrometer of the ATLAS experiment is presented. High quality specifications on the detectors to be produced demanded creation of a workplace with stable temperature and humidity, as well as minimum quantity of dust in the room. Checking of parameters of intra-room air during long period of continuous work has confirmed correctness of the designed characteristics of the climatic system installed in the clean room. The room large volume (∼ 190 m 3 ), the powerful and flexible climatic system, and simplicity of service allow assembling of detectors with length up to 5 m. Subsequent checking of functionality of the assembled detectors has shown high quality of assembling (the amount of rejected tubes does not exceed 2%). It demonstrates conformity to the assembling quality requirements for mass production of drift chambers for the muon spectrometer. (author)

Clean Industrial Room for Drift Tube Assembling

CERN Document Server

Glonti, GL; Evtoukhovitch, P G; Kroa, G; Manz, A; Potrap, I N; Rihter, P; Stoletov, G D; Tskhadadze, E G; Chepurnov, V F; Chirkov, A V; Shelkov, G A

2001-01-01

Description of a clean industrial room for assembly of drift tubes for the muon spectrometer of the ATLAS experiment is presented. High quality specifications on the detectors to be produced demanded creation of a workplace with stable temperature and humidity, as well as minimum quantity of dust in the room. Checking of parameters of intra-room air during long period of continuous work has been confirmed correctness of the designed characteristics of the climatic system installed in the clean room. The room large volum (\\sim 190 m^3), the powerful and flexible climatic system, and simplicity of service allow assembling of detectors with length up to 5 m. Subsequent checking of functionality of the assembled detectors has shown high quality of assembling (the amount of rejected tubes does not exceed 2 %). It demonstrates conformity to the assembling quality requirements for mass production of drift chambers for the muon spectrometer.

Scram system with continuos check

International Nuclear Information System (INIS)

Rodriguez Sacco, Walter.

1976-02-01

The equipment described pretends to be a further step to the use of integrated circuits in nuclear instrumentation, considering that this type of control was traditionally carried out on the bases of electromechanical elements. A continuous self-check method has been applied in accordance with the high reliability requiered for this type of equipments. The developed equipment fulfils the condition that any deficiency in its component elements, causes an anormal self-detected operation. The equipment covers two systems: the Scram one, that includes the sequence generator-detector, the rods check and scram chain, and the Check system that uses pulses from the sequence detector. (author) [es

CasEMBLR: Cas9-Facilitated Multiloci Genomic Integration of in Vivo Assembled DNA Parts in Saccharomyces cerevisiae

DEFF Research Database (Denmark)

Jakociunas, Tadas; Rajkumar, Arun Stephen; Zhang, Jie

2015-01-01

, we present a method for marker-free multiloci integration of in vivo assembled DNA parts. By the use of CRISPR/Cas9-mediated one-step double-strand breaks at single, double and triple integration sites we report the successful in vivo assembly and chromosomal integration of DNA parts. We call our...

Assembly and Multiplex Genome Integration of Metabolic Pathways in Yeast Using CasEMBLR.

Science.gov (United States)

Jakočiūnas, Tadas; Jensen, Emil D; Jensen, Michael K; Keasling, Jay D

2018-01-01

Genome integration is a vital step for implementing large biochemical pathways to build a stable microbial cell factory. Although traditional strain construction strategies are well established for the model organism Saccharomyces cerevisiae, recent advances in CRISPR/Cas9-mediated genome engineering allow much higher throughput and robustness in terms of strain construction. In this chapter, we describe CasEMBLR, a highly efficient and marker-free genome engineering method for one-step integration of in vivo assembled expression cassettes in multiple genomic sites simultaneously. CasEMBLR capitalizes on the CRISPR/Cas9 technology to generate double-strand breaks in genomic loci, thus prompting native homologous recombination (HR) machinery to integrate exogenously derived homology templates. As proof-of-principle for microbial cell factory development, CasEMBLR was used for one-step assembly and marker-free integration of the carotenoid pathway from 15 exogenously supplied DNA parts into three targeted genomic loci. As a second proof-of-principle, a total of ten DNA parts were assembled and integrated in two genomic loci to construct a tyrosine production strain, and at the same time knocking out two genes. This new method complements and improves the field of genome engineering in S. cerevisiae by providing a more flexible platform for rapid and precise strain building.

A participatory and integrative approach to improve productivity and ergonomics in assembly

NARCIS (Netherlands)

Looze, M.P. de; Rhijn, J.W. van; Deursen, J. van; Tuinzaad, G.H.; Reijneveld, C.N.

2003-01-01

A participatory and integrative approach was applied to improve the productivity and ergonomics of the assembly lines in two factories, producing magnetic stop valves and office furniture, respectively. Main elements of the approach are the active participation of the company and the integration of

Assembly and Multiplex Genome Integration of Metabolic Pathways in Yeast Using CasEMBLR

DEFF Research Database (Denmark)

Jakočiūnas, Tadas; Jensen, Emil D.; Jensen, Michael Krogh

2018-01-01

and marker-free integration of the carotenoid pathway from 15 exogenously supplied DNA parts into three targeted genomic loci. As a second proof-of-principle, a total of ten DNA parts were assembled and integrated in two genomic loci to construct a tyrosine production strain, and at the same time knocking......Genome integration is a vital step for implementing large biochemical pathways to build a stable microbial cell factory. Although traditional strain construction strategies are well established for the model organism Saccharomyces cerevisiae, recent advances in CRISPR/Cas9-mediated genome...... engineering allow much higher throughput and robustness in terms of strain construction. In this chapter, we describe CasEMBLR, a highly efficient and marker-free genome engineering method for one-step integration of in vivo assembled expression cassettes in multiple genomic sites simultaneously. Cas...

INTEGRATED APPROACH TO GENERATION OF PRECEDENCE RELATIONS AND PRECEDENCE GRAPHS FOR ASSEMBLY SEQUENCE PLANNING

Institute of Scientific and Technical Information of China (English)

无

2002-01-01

An integrated approach to generation of precedence relations and precedence graphs for assembly sequence planning is presented, which contains more assembly flexibility. The approach involves two stages. Based on the assembly model, the components in the assembly can be divided into partially constrained components and completely constrained components in the first stage, and then geometric precedence relation for every component is generated automatically. According to the result of the first stage, the second stage determines and constructs all precedence graphs. The algorithms of these two stages proposed are verified by two assembly examples.

New faces of porous Prussian blue: interfacial assembly of integrated hetero-structures for sensing applications.

Science.gov (United States)

Kong, Biao; Selomulya, Cordelia; Zheng, Gengfeng; Zhao, Dongyuan

2015-11-21

Prussian blue (PB), the oldest synthetic coordination compound, is a classic and fascinating transition metal coordination material. Prussian blue is based on a three-dimensional (3-D) cubic polymeric porous network consisting of alternating ferric and ferrous ions, which provides facile assembly as well as precise interaction with active sites at functional interfaces. A fundamental understanding of the assembly mechanism of PB hetero-interfaces is essential to enable the full potential applications of PB crystals, including chemical sensing, catalysis, gas storage, drug delivery and electronic displays. Developing controlled assembly methods towards functionally integrated hetero-interfaces with adjustable sizes and morphology of PB crystals is necessary. A key point in the functional interface and device integration of PB nanocrystals is the fabrication of hetero-interfaces in a well-defined and oriented fashion on given substrates. This review will bring together these key aspects of the hetero-interfaces of PB nanocrystals, ranging from structure and properties, interfacial assembly strategies, to integrated hetero-structures for diverse sensing.

The design and analysis of integral assembly experiments for CTR neutronics

International Nuclear Information System (INIS)

Beynon, T.D.; Curtis, R.H.; Lambert, C.

1978-01-01

The use of simple-geometry integral assemblies of lithium metal or lithium compounds for the study of the neutronics of various CTR designs is considered and four recent experiments are analysed. The relatively long mean free path of neutrons in these assemblies produces significantly different design problems from those encountered in similar experiments for fission reactor design. By considering sensitivity profiles for various parameters it is suggested that experiments can be designed to be optimised for data adjustments. (author)

Integrating succession and community assembly perspectives [version 1; referees: 2 approved

Directory of Open Access Journals (Sweden)

Cynthia Chang

2016-09-01

Full Text Available Succession and community assembly research overlap in many respects, such as through their focus on how ecological processes like dispersal, environmental filters, and biotic interactions influence community structure. Indeed, many recent advances have been made by successional studies that draw on modern analytical techniques introduced by contemporary community assembly studies. However, community assembly studies generally lack a temporal perspective, both on how the forces structuring communities might change over time and on how historical contingency (e.g. priority effects and legacy effects and complex transitions (e.g. threshold effects might alter community trajectories. We believe a full understanding of the complex interacting processes that shape community dynamics across large temporal scales can best be achieved by combining concepts, tools, and study systems into an integrated conceptual framework that draws upon both succession and community assembly theory.

THE BASIC PRINCIPLES OF THE INTEGRATED MANAGEMENT OF THE PROCESS OF ASSEMBLY AND THREADING

Directory of Open Access Journals (Sweden)

Anton Skorkin

2017-11-01

Full Text Available The subject matter of this article is the issues related to the integrated management of assembling operations of fastening and threading elements at all stages of their implementation. The goal is to develop the generalized structure of the data management system of the process of assembly and threading. The objectives are: to justify the principles of managing the assembly and threading process at each stage of the assembly to improve the efficiency of these operations, to study the power, accuracy and performance characteristics of the connections and to draw the conclusion that suggested the theory of assembly management is efficient. The following results are obtained. The article presents the analytical dependencies of the force indexes of threading in the course of the package and sheet assembly, including the tightening force while joining; the assembly of a multilayered package of dissimilar sheet materials was analyzed. On the basis of the theoretical analysis, the dependences of the power indices of threading during the package and sheet assembly were determined. The assembly of the package of sheet materials was investigated, including a multilayered package of dissimilar materials of a “metal-plastic” type. Conclusions. The process of assembling threaded joints with the use of management principles was used; these principles enable increasing the efficiency of the assembly process, reducing the complexity of the basic operations, and improving the quality of the joints obtained. The use adaptive control of the screwing speed on the main threading transitions is suggested for reducing the torque.  The technology of making threaded joints with given properties is developed, the main ways of increasing the efficiency of assembly and threading processes are determined on the basis of the integrated control system for the assembly process.

Structural characterisation of medically relevant protein assemblies by integrating mass spectrometry with computational modelling.

Science.gov (United States)

Politis, Argyris; Schmidt, Carla

2018-03-20

Structural mass spectrometry with its various techniques is a powerful tool for the structural elucidation of medically relevant protein assemblies. It delivers information on the composition, stoichiometries, interactions and topologies of these assemblies. Most importantly it can deal with heterogeneous mixtures and assemblies which makes it universal among the conventional structural techniques. In this review we summarise recent advances and challenges in structural mass spectrometric techniques. We describe how the combination of the different mass spectrometry-based methods with computational strategies enable structural models at molecular levels of resolution. These models hold significant potential for helping us in characterizing the function of protein assemblies related to human health and disease. In this review we summarise the techniques of structural mass spectrometry often applied when studying protein-ligand complexes. We exemplify these techniques through recent examples from literature that helped in the understanding of medically relevant protein assemblies. We further provide a detailed introduction into various computational approaches that can be integrated with these mass spectrometric techniques. Last but not least we discuss case studies that integrated mass spectrometry and computational modelling approaches and yielded models of medically important protein assembly states such as fibrils and amyloids. Copyright © 2017 The Author(s). Published by Elsevier B.V. All rights reserved.

Nondestructive Assay Data Integration with the SKB-50 Assemblies - FY16 Update

International Nuclear Information System (INIS)

Tobin, Stephen Joseph; Fugate, Michael Lynn; Trellue, Holly Renee; DeBaere, Paul; Sjoland, Anders; Liljenfeldt, Henrik; Hu, Jianwei; Backstrom, Ulrika; Bengtsson, Martin; Burr, Tomas; Eliasson, Annika; Favalli, Andrea; Gauld, Ian; Grogan, Brandon; Jansson, Peter; Junell, Henrik; Schwalbach, Peter; Vaccaro, Stefano; Vo, Duc Ta; Wildestrand, Henrik

2016-01-01

A project to research the application of non-destructive assay (NDA) techniques for spent fuel assemblies is underway at the Central Interim Storage Facility for Spent Nuclear Fuel (for which the Swedish acronym is Clab) in Oskarshamn, Sweden. The research goals of this project contain both safeguards and non-safeguards interests. These nondestructive assay (NDA) technologies are designed to strengthen the technical toolkit of safeguard inspectors and others to determine the following technical goals more accurately; Verify initial enrichment, burnup, and cooling time of facility declaration for spent fuel assemblies; Detect replaced or missing pins from a given spent fuel assembly to confirm its integrity; and Estimate plutonium mass and related plutonium and uranium fissile mass parameters in spent fuel assemblies. Estimate heat content, and measure reactivity (multiplication).

Nondestructive Assay Data Integration with the SKB-50 Assemblies - FY16 Update

Energy Technology Data Exchange (ETDEWEB)

Tobin, Stephen Joseph [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Fugate, Michael Lynn [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Trellue, Holly Renee [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); DeBaere, Paul [DG Energy, Luxembourg (Germany); Sjoland, Anders [Swedish Nuclear Fuel and Waste Management Company, Stockholm (Sweden); Liljenfeldt, Henrik [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hu, Jianwei [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Backstrom, Ulrika [Swedish Nuclear Fuel and Waste Management Company, Stockholm (Sweden); Vattenfall AB, Stockholm (Sweden); Bengtsson, Martin [Swedish Nuclear Fuel and Waste Management Company, Stockholm (Sweden); Vattenfall AB, Stockholm (Sweden); Burr, Tomas [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); International Atomic Energy Agency, Vienna (Austria); Eliasson, Annika [Swedish Nuclear Fuel and Waste Management Company, Stockholm (Sweden); Favalli, Andrea [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Gauld, Ian [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Grogan, Brandon [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jansson, Peter [Uppsala Univ. (Sweden); Junell, Henrik [Swedish Nuclear Fuel and Waste Management Company, Stockholm (Sweden); Schwalbach, Peter [DG Energy, Luxembourg (Germany); Vaccaro, Stefano [DG Energy, Luxembourg (Germany); Vo, Duc Ta [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Wildestrand, Henrik [Swedish Nuclear Fuel and Waste Management Company, Stockholm (Sweden); Vattenfall AB, Stockholm (Sweden)

2016-10-28

A project to research the application of non-destructive assay (NDA) techniques for spent fuel assemblies is underway at the Central Interim Storage Facility for Spent Nuclear Fuel (for which the Swedish acronym is Clab) in Oskarshamn, Sweden. The research goals of this project contain both safeguards and non-safeguards interests. These nondestructive assay (NDA) technologies are designed to strengthen the technical toolkit of safeguard inspectors and others to determine the following technical goals more accurately; Verify initial enrichment, burnup, and cooling time of facility declaration for spent fuel assemblies; Detect replaced or missing pins from a given spent fuel assembly to confirm its integrity; and Estimate plutonium mass and related plutonium and uranium fissile mass parameters in spent fuel assemblies. Estimate heat content, and measure reactivity (multiplication).

Structural integrity assessment and stress measurement of CHASNUPP-1 fuel assembly

Directory of Open Access Journals (Sweden)

Waseem

2016-01-01

Full Text Available Fuel assembly of the PWR nuclear power plant is a long and flexible structure. This study has been made in an attempt to find the structural integrity of the fuel assembly (FA of Chashma Nuclear Power Plant-1 (CHASNUPP-1 at room temperature in air. The non-linear contact and structural tensile analysis have been performed using ANSYS 13.0, in order to determine the fuel assembly (FA elongation behaviour as well as the location and values of the stress intensity and stresses developed in axial direction under applied tensile load of 9800 N or 2 g being the fuel assembly handling or lifting load [Y. Zhang et al., Fuel assembly design report, SNERDI, China, 1994]. The finite element (FE model comprises spacer grids, fuel rods, flexible contacts between the fuel rods and grid's supports system and guide thimbles with dash-pots and flow holes, in addition to the spot welds between spacer grids and guide thimbles, has been developed using Shell181, Conta174 and Targe170 elements. FA is a non-straight structure. The actual behavior of the geometry is non-linear due to its curvature or design tolerance. It has been observed that fuel assembly elongation values obtained through FE analysis and experiment [SNERDI Tech. Doc., Mechanical strength and calculation for fuel assembly, Technical Report, F3.2.1, China, 1994] under applied tensile load are comparable and show approximately linear behaviors. Therefore, it seems that the permanent elongation of fuel assembly may not occur at the specified load. Moreover, the values of stresses obtained at different locations of the fuel assembly are also comparable with the stress values of the experiment determined at the same locations through strain gauges. Since the results of both studies (analytical and experimental are comparable, therefore, validation of the FE methodology is confirmed. The stress intensity of the FE model and maximum stresses developed along the guide thimbles in axial direction are

The use of check valve performance data to support new concepts (probabilistic risk assessment, condition monitoring) for check valve program

Energy Technology Data Exchange (ETDEWEB)

Hart, K.A.; Gower, D.

1996-12-01

The concept of developing an integrated check valve database based on the Nuclear Power Reliability Data System (NPRDS) data was presented at the last Symposium. The Nuclear Industry Check Valve Group (NIC), working in cooperation with the Oak Ridge National Laboratory (ORNL), has completed an operational database of check valve performance from 1984 to the present. NIC has committed to the nuclear industry to periodically update the data and maintain this information accessible. As the new concepts of probabilistic risk analysis and condition monitoring are integrated into the American Society of Mechanical Engineers (ASME) Code, a critical element will be performance data. From check valve performance data, feasible failure modes and rates can be established. When a failure rate or frequency of failures can be established based on a significant enough population (sampling), a more solid foundation for focusing resources and determining appropriate frequencies and testing can be determined. The presentation will give the updated status of the NIC Check Valve Performance Database covering (1) methodology used to combine the original ORNL data; (2) process/controls established for continuing update and refinement of the data; (3) discussion of how this data is being utilized by (a) OM-22 for condition monitoring, and (b) risk-based inservice testing work of Westinghouse Owners` Group; and (4) results/trends of data evaluations. At the 1994 Symposium, ORNL provided an update as of 1991 to their original work of 1984 -1990 which they had performed to characterize check valve degradations and failures in the nuclear industry. These characterizations will be updated to 1995 and additional reviews provided to give insight into the current condition and trends of check valve performance.

The use of check valve performance data to support new concepts (probabilistic risk assessment, condition monitoring) for check valve program

International Nuclear Information System (INIS)

Hart, K.A.; Gower, D.

1996-01-01

The concept of developing an integrated check valve database based on the Nuclear Power Reliability Data System (NPRDS) data was presented at the last Symposium. The Nuclear Industry Check Valve Group (NIC), working in cooperation with the Oak Ridge National Laboratory (ORNL), has completed an operational database of check valve performance from 1984 to the present. NIC has committed to the nuclear industry to periodically update the data and maintain this information accessible. As the new concepts of probabilistic risk analysis and condition monitoring are integrated into the American Society of Mechanical Engineers (ASME) Code, a critical element will be performance data. From check valve performance data, feasible failure modes and rates can be established. When a failure rate or frequency of failures can be established based on a significant enough population (sampling), a more solid foundation for focusing resources and determining appropriate frequencies and testing can be determined. The presentation will give the updated status of the NIC Check Valve Performance Database covering (1) methodology used to combine the original ORNL data; (2) process/controls established for continuing update and refinement of the data; (3) discussion of how this data is being utilized by (a) OM-22 for condition monitoring, and (b) risk-based inservice testing work of Westinghouse Owners' Group; and (4) results/trends of data evaluations. At the 1994 Symposium, ORNL provided an update as of 1991 to their original work of 1984 -1990 which they had performed to characterize check valve degradations and failures in the nuclear industry. These characterizations will be updated to 1995 and additional reviews provided to give insight into the current condition and trends of check valve performance

Engineering Abstractions in Model Checking and Testing

DEFF Research Database (Denmark)

Achenbach, Michael; Ostermann, Klaus

2009-01-01

Abstractions are used in model checking to tackle problems like state space explosion or modeling of IO. The application of these abstractions in real software development processes, however, lacks engineering support. This is one reason why model checking is not widely used in practice yet...... and testing is still state of the art in falsification. We show how user-defined abstractions can be integrated into a Java PathFinder setting with tools like AspectJ or Javassist and discuss implications of remaining weaknesses of these tools. We believe that a principled engineering approach to designing...... and implementing abstractions will improve the applicability of model checking in practice....

Technical findings and regulatory analysis for Generic Safety Issue II.E.4.3, ''Containment Integrity Check''

International Nuclear Information System (INIS)

Serkiz, A.W.

1988-04-01

This report contains the technical findings and regulatory analysis for Generic Safety Issue II.E.4.3, ''Containment Integrity Check.'' An evaluation of the containment isolation history from 1965 to 1983 reveals that (except for a small number of events) containment integrity has been maintained and that the majority of reported events have been events related to exceeding Technical Specification limits (or 0.6 of the allowable leakage level). In addition, more recent risk analyses have shown that allowable leakage rates even if increased by a factor of 10 would not significantly increase risk. Potential methods of continuous monitoring are identified and evaluated. Therefore, these technical findings and risk evaluations support closure of Generic Safety Issue II.E.4.3

Self-assembly as a design tool for the integration of photonic structures into excitonic solar cells

KAUST Repository

Guldin, S.

2011-09-20

One way to successfully enhance light harvesting of excitonic solar cells is the integration of optical elements that increase the photon path length in the light absorbing layer. Device architectures which incorporate structural order in form of one- or three-dimensional refractive index lattices can lead to the localization of light in specific parts of the spectrum, while retaining the cell\\'s transparency in others. Herein, we present two routes for the integration of photonic crystals (PCs) into dye-sensitized solar cells (DSCs). In both cases, the self-assembly of soft matter plays a key role in the fabrication process of the TiO2 electrode. One approach relies on a combination of colloidal self-assembly and the self-assembly of block copolymers, resulting in a double layer dye-sensitized solar cell with increased light absorption from the 3D PC element. An alternative route is based on the fact that the refractive index of the mesoporous layer can be finely tuned by the interplay between block copolymer self-assembly and hydrolytic TiO2 sol-gel chemistry. Alternating deposition of high and low refractive index layers enables the integration of a 1D PC into a DSC.

Improvement of seawater booster pump outlet check valve

International Nuclear Information System (INIS)

Li Xuning; Du Yansong; Huang Huimin

2010-01-01

Conventional island seawater booster pump set of QNPC 310 MWe unit are very important in the whole circulating cooling system, and the integrate function of seawater booster pump outlet check valve is the foundation of steady operation of the seawater booster pump set. The article mainly introduce that through the analyses to the reason to the problem that the seawater booster pump outlet check valve of QNPC 310 MWe unit appeared in past years by our team, and considering the influence of operation condition and circumstance, the team improve the seawater booster pump outlet check valve from swing check valve to shuttle check valve which operate more appropriately in the system. By the test of continuous practice, we make further modification to the inner structure of shuttle check valve contrapuntally, and therefore we solve the problem in seawater booster pump outlet check valve fundamentally which has troubled the security of system operation in past years, so we realize the aim of technical improvement and ensure that the system operate in safety and stability. (authors)

Simple Check Valves for Microfluidic Devices

Science.gov (United States)

Willis, Peter A.; Greer, Harold F.; Smith, J. Anthony

2010-01-01

A simple design concept for check valves has been adopted for microfluidic devices that consist mostly of (1) deformable fluorocarbon polymer membranes sandwiched between (2) borosilicate float glass wafers into which channels, valve seats, and holes have been etched. The first microfluidic devices in which these check valves are intended to be used are micro-capillary electrophoresis (microCE) devices undergoing development for use on Mars in detecting compounds indicative of life. In this application, it will be necessary to store some liquid samples in reservoirs in the devices for subsequent laboratory analysis, and check valves are needed to prevent cross-contamination of the samples. The simple check-valve design concept is also applicable to other microfluidic devices and to fluidic devices in general. These check valves are simplified microscopic versions of conventional rubber- flap check valves that are parts of numerous industrial and consumer products. These check valves are fabricated, not as separate components, but as integral parts of microfluidic devices. A check valve according to this concept consists of suitably shaped portions of a deformable membrane and the two glass wafers between which the membrane is sandwiched (see figure). The valve flap is formed by making an approximately semicircular cut in the membrane. The flap is centered over a hole in the lower glass wafer, through which hole the liquid in question is intended to flow upward into a wider hole, channel, or reservoir in the upper glass wafer. The radius of the cut exceeds the radius of the hole by an amount large enough to prevent settling of the flap into the hole. As in a conventional rubber-flap check valve, back pressure in the liquid pushes the flap against the valve seat (in this case, the valve seat is the adjacent surface of the lower glass wafer), thereby forming a seal that prevents backflow.

CheckMATE 2: From the model to the limit

Science.gov (United States)

Dercks, Daniel; Desai, Nishita; Kim, Jong Soo; Rolbiecki, Krzysztof; Tattersall, Jamie; Weber, Torsten

2017-12-01

We present the latest developments to the CheckMATE program that allows models of new physics to be easily tested against the recent LHC data. To achieve this goal, the core of CheckMATE now contains over 60 LHC analyses of which 12 are from the 13 TeV run. The main new feature is that CheckMATE 2 now integrates the Monte Carlo event generation via MadGraph5_aMC@NLO and Pythia 8. This allows users to go directly from a SLHA file or UFO model to the result of whether a model is allowed or not. In addition, the integration of the event generation leads to a significant increase in the speed of the program. Many other improvements have also been made, including the possibility to now combine signal regions to give a total likelihood for a model.

Development of Out-pile Test Technology for Fuel Assembly Performance Verification

Energy Technology Data Exchange (ETDEWEB)

Chun, Tae Hyun; In, W. K.; Oh, D. S. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)] (and others)

2007-03-15

Out-pile tests with full scale fuel assembly are to verify the design and to evaluate the performance of the final products. HTL for the hydraulic tests and FAMeCT for mechanical/structural tests were constructed in this project. The maximum operating conditions of HTL are 30 bar, 320 .deg. C, and 500 m3/hr. This facility can perform the pressure drop test, fuel assembly uplift test, and flow induced vibration test. FAMeCT can perform the bending and vibration tests. The verification of the developed facilities were carried out by comparing the reference data of the fuel assembly which was obtained at the Westinghouse Co. The compared data showed a good coincidence within uncertainties. FRETONUS was developed for high temperature and high pressure fretting wear simulator and performance test. A performance test was conducted for 500 hours to check the integrity, endurance, data acquisition capability of the simulator. The technology of turbulent flow analysis and finite element analysis by computation was developed. From the establishments of out-pile test facilities for full scale fuel assembly, the domestic infrastructure for PWR fuel development has been greatly upgraded.

Integrity Evaluation of Control Rod Assembly for Sodium-Cooled Fast Reactor due to Drop Impact

Energy Technology Data Exchange (ETDEWEB)

Lee, Hyun Seung; Yoon, Kyung Ho; Kim, Hyung Kyu; Cheon, Jin Sik; Lee, Chan Bock [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2017-03-15

The CA (Control Assembly) of an SFR has a CRA(Control Rod Assembly) with an inner duct and control rod. During an emergency situation, the CRA falls into the duct of the CA for a rapid shut-down. The drop time and impact velocity of the CRA are important parameters with respect to the reactivity insertion time and the structural integrity of the CRA. The objective of this study was to investigate the dynamic behavior and integrity of the CRA owing to a drop impact. The impact analysis of the CRA under normal/abnormal drop conditions was carried out using the commercial FEM code LS-DYNA. Results of the drop impact analysis demonstrated that the CRA maintained structural integrity, and could be safely inserted into the flow hole of the damper under abnormal conditions.

Integrity Evaluation of Control Rod Assembly for Sodium-Cooled Fast Reactor due to Drop Impact

International Nuclear Information System (INIS)

Lee, Hyun Seung; Yoon, Kyung Ho; Kim, Hyung Kyu; Cheon, Jin Sik; Lee, Chan Bock

2017-01-01

The CA (Control Assembly) of an SFR has a CRA(Control Rod Assembly) with an inner duct and control rod. During an emergency situation, the CRA falls into the duct of the CA for a rapid shut-down. The drop time and impact velocity of the CRA are important parameters with respect to the reactivity insertion time and the structural integrity of the CRA. The objective of this study was to investigate the dynamic behavior and integrity of the CRA owing to a drop impact. The impact analysis of the CRA under normal/abnormal drop conditions was carried out using the commercial FEM code LS-DYNA. Results of the drop impact analysis demonstrated that the CRA maintained structural integrity, and could be safely inserted into the flow hole of the damper under abnormal conditions.

Human Contamination in Public Genome Assemblies.

Science.gov (United States)

Kryukov, Kirill; Imanishi, Tadashi

2016-01-01

Contamination in genome assembly can lead to wrong or confusing results when using such genome as reference in sequence comparison. Although bacterial contamination is well known, the problem of human-originated contamination received little attention. In this study we surveyed 45,735 available genome assemblies for evidence of human contamination. We used lineage specificity to distinguish between contamination and conservation. We found that 154 genome assemblies contain fragments that with high confidence originate as contamination from human DNA. Majority of contaminating human sequences were present in the reference human genome assembly for over a decade. We recommend that existing contaminated genomes should be revised to remove contaminated sequence, and that new assemblies should be thoroughly checked for presence of human DNA before submitting them to public databases.

ITER design, integration and assembly studies assisted by virtual reality

Energy Technology Data Exchange (ETDEWEB)

Keller, D., E-mail: delphine.keller@cea.fr [CEA, IRFM, F-13108 St-Paul-Lez-Durance (France); ITER Organization, Route de Vinon-sur-Verdon, F-13115 St-Paul-Lez-Durance (France); Doceul, L.; Ferlay, F.; Jiolat, G. [CEA, IRFM, F-13108 St-Paul-Lez-Durance (France); Cordier, J.J.; Kuehn, I.; Manfreo, B.; Reich, J. [ITER Organization, Route de Vinon-sur-Verdon, F-13115 St-Paul-Lez-Durance (France)

2013-10-15

Highlights: ► VR technologies applied to Fusion enable to better and faster understand integration issues. ► Problems are solved and validated on a numerical mock up. ► Integration and accessibility issues can be identified in the earliest design. ► VR technologies are very helpful for assembly and maintenance operation simulations. ► New tools for real time simulations of hands-on operations are currently under development. -- Abstract: In a project like ITER where schedule, resources and cost is continuously optimized, emphasis has to be put on developing long lead items first while keeping other designs very low in definition. Hence, at a particular stage of the project, several components have to coexist in the integrated system while handling different level of maturity. Therefore, all the difficulty consists in managing the interfaces between all these components and to minimize the risk of design changes on the most advanced components. As a future exploitant, ITER is in charge of managing these interfaces and to ensure that maintenance of especially safety important class components (SIC) is feasible. These operation and maintenance constraints have to be taken into account since the earliest design of the components itselves. In this context, CEA IRFM is taking the benefit of using its virtual reality (VR) platform and simulation tools to assist ITER Organization in improving the efficiency of the inconsistencies identification and the machine sub-system design optimization. Currently, two contracts are on-going: the first one concerns the cryostat and in-vessel components; the second one concerns the overall Tokamak (TKM) and diagnostic buildings. This paper describes how VR tools applied to fusion and especially to ITER can help design and Integration with taking into account assembly and maintenance requirements at early stage in the design of complex systems.

ITER design, integration and assembly studies assisted by virtual reality

International Nuclear Information System (INIS)

Keller, D.; Doceul, L.; Ferlay, F.; Jiolat, G.; Cordier, J.J.; Kuehn, I.; Manfreo, B.; Reich, J.

2013-01-01

Highlights: ► VR technologies applied to Fusion enable to better and faster understand integration issues. ► Problems are solved and validated on a numerical mock up. ► Integration and accessibility issues can be identified in the earliest design. ► VR technologies are very helpful for assembly and maintenance operation simulations. ► New tools for real time simulations of hands-on operations are currently under development. -- Abstract: In a project like ITER where schedule, resources and cost is continuously optimized, emphasis has to be put on developing long lead items first while keeping other designs very low in definition. Hence, at a particular stage of the project, several components have to coexist in the integrated system while handling different level of maturity. Therefore, all the difficulty consists in managing the interfaces between all these components and to minimize the risk of design changes on the most advanced components. As a future exploitant, ITER is in charge of managing these interfaces and to ensure that maintenance of especially safety important class components (SIC) is feasible. These operation and maintenance constraints have to be taken into account since the earliest design of the components itselves. In this context, CEA IRFM is taking the benefit of using its virtual reality (VR) platform and simulation tools to assist ITER Organization in improving the efficiency of the inconsistencies identification and the machine sub-system design optimization. Currently, two contracts are on-going: the first one concerns the cryostat and in-vessel components; the second one concerns the overall Tokamak (TKM) and diagnostic buildings. This paper describes how VR tools applied to fusion and especially to ITER can help design and Integration with taking into account assembly and maintenance requirements at early stage in the design of complex systems

PSYCHE, ENDF/B Data Consistency Check in ENDF Format

International Nuclear Information System (INIS)

Dunford, Charles L.

2007-01-01

1 - Description of program or function: PSYCHE is a program for checking the physics content of an evaluated data file. It can recognise the difference between ENDF-5 or ENDF-6 formats and performs its tests accordingly. Version 7.01 (April 2005): set success flag after return from begin, added potential scattering test formerly in Fizcon. Version 7.02 (May 2005): Fixed bug in calculation of L=2 penetrability. 2 - Method of solution: PSYCHE checks for energy conservation for emitted neutrons and photons, checks Wick's limit for elastic scattering, analyses resonance parameter statistics, calculates thermal cross sections and resonance integrals, examines continuity across resonance region boundaries and checks 'Q' values against mass tables

General Principles of Integrity Checking of Digital Images and Application for Steganalysis

Directory of Open Access Journals (Sweden)

Kobozeva Alla A.

2016-06-01

Full Text Available The new common approach for integrity checking of digital images is developed. The new features of formal parameters defining image are revealed, theoretically grounded and practically tested. The characteristics of the mutual arrangement of left and right singular vectors corresponding to the largest singular value of the image’s matrix (block of matrix and the vector composed of singular numbers is obtained. Formal parameters are obtained using normal singular decomposition of matrix (block of matrix which is uniquely determined. It is shown that for most blocks of original image (no matter lossy or lossless the angle between the left (right mentioned singular vector and vector composed of singular numbers is defined by the angle between the n-optimal vector and the vector of standard basis of the range corresponding dimension. It is shown that the determined feature brakes for the mentioned formal parameters in a non-original image. This shows the integrity violation of the image, i.e. the existence of the additional information embedded using steganography algorithms. So this can be used as a basis for development of new universal steganography methods and algorithms, and one example of the realization is proposed. The efficiency of the proposed algorithm won’t depend on the details of steganography method used for embedding. All the obtained results can be easily adapted for the digital video and audio analysis.

Transaction management with integrity checking

DEFF Research Database (Denmark)

Martinenghi, Davide; Christiansen, Henning

2005-01-01

Database integrity constraints, understood as logical conditions that must hold for any database state, are not fully supported by current database technology. It is typically up to the database designer and application programmer to enforce integrity via triggers or tests at the application level....... 2.~In concurrent database systems, besides the traditional correctness criterion, the execution schedule must ensure that the different transactions can overlap in time without destroying the consistency requirements tested by other, concurrent transactions....

Check, check, double check: checking the autopilot causes distrust : Experimental studies on the effects of compulsive perseveration

NARCIS (Netherlands)

Dek, E.C.P.

2015-01-01

Obsessive-compulsive disorder (OCD) is characterized by persistent doubt. The majority of patients with OCD engage in repeated checking to reduce these feelings of uncertainty. However, numerous studies demonstrated that repetitive behavior ironically increases uncertainty: perseverative checking

Structural Integrity Evaluation for the IVTM Gripper in PGSFR

Energy Technology Data Exchange (ETDEWEB)

Kim, S. H.; Koo, G. H. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-10-15

The materials of the gripper used for the analysis are the 316SS in the gripper body parts and the Inconel 718 alloy in the gripper finger parts, respectively. For six sections of the IVTM gripper, the structural integrity according to ASME-NB design rule is checked for the dead weight and refueling load because it is under the low temperature during the refueling operation. As a result of the evaluation, it is reviewed the IVTM gripper design has the structural adequacy. IVTM (In-Vessel Transfer Machine) is the instrument for transferring the core assembly inside the reactor vessel. The IVTM use the gripper finger for the connection and disconnection with the core assembly, which is designed to be possible for the rotation and vertical movement of the gripper. We can see that the IVTM gripper is supported by the gripper guide structure. In the gripper movement, the gripper is lowered to pick up the core assembly with its fingers closed. On contact with the end of the core assembly, the gripper fingers are opened, and then connected with the core assembly. The gripper is then raised with the core assembly. This is the gripper mechanism to handle the core assembly. The purpose of this study is to analyze the gripper stresses and displacements for the design loads applied to the gripper, and also to evaluate the structural integrity of the gripper design for 60 year lifetime.

Integration of disabled people in an automated work process

Science.gov (United States)

Jalba, C. K.; Muminovic, A.; Epple, S.; Barz, C.; Nasui, V.

2017-05-01

Automation processes enter more and more into all areas of life and production. Especially people with disabilities can hardly keep step with this change. In sheltered workshops in Germany people with physical and mental disabilities get help with much dedication, to be integrated into the work processes. This work shows that cooperation between disabled people and industrial robots by means of industrial image processing can successfully result in the production of highly complex products. Here is described how high-pressure hydraulic pumps are assembled by people with disabilities in cooperation with industrial robots in a sheltered workshop. After the assembly process, the pumps are checked for leaks at very high pressures in a completely automated process.

Integrating software testing and run-time checking in an assertion verification framework

OpenAIRE

Mera, E.; López García, Pedro; Hermenegildo, Manuel V.

2009-01-01

We have designed and implemented a framework that unifies unit testing and run-time verification (as well as static verification and static debugging). A key contribution of our approach is that a unified assertion language is used for all of these tasks. We first propose methods for compiling runtime checks for (parts of) assertions which cannot be verified at compile-time via program transformation. This transformation allows checking preconditions and postconditions, including conditional...

Transient analysis for a system with a tilted disc check valve

International Nuclear Information System (INIS)

Jeung, Jaesik; Lee, Kyukwang; Cho, Daegwan

2014-01-01

Check valves are used to prevent reverse flow conditions in a variety of systems in nuclear power plants. When a check valve is closed by a reverse flow, the transient load can jeopardize the structural integrity on the piping system and its supports. It may also damage intended function of the in-line components even though the severity of the load differs and depends strongly on types of the check valves. To incorporate the transient load in the piping system, it is very important to properly predict the system response to transients such as a check valve closure accompanied by pump trip and to evaluate the system transient. The one-dimensional transient simulation codes such as the RELAP5/MOD3.3 and TRACE were used. There has not been a single model that integrates the two codes to handle the behavior of a tilted disc check valve, which is designed to mitigate check valve slams by shorting the travel of the disc. In this paper a model is presented to predict the dynamic motion of a tilted disc check valve in the transient simulation using the RELAP5/MOD3.3 code and the model is incorporated in a system transient analysis using control variables of the code. In addition, transient analysis for Essential Service Water (ESW) system is performed using the proposed model and the associated load is evaluated for the system. (author)

A voice-actuated wind tunnel model leak checking system

Science.gov (United States)

Larson, William E.

1989-01-01

A computer program has been developed that improves the efficiency of wind tunnel model leak checking. The program uses a voice recognition unit to relay a technician's commands to the computer. The computer, after receiving a command, can respond to the technician via a voice response unit. Information about the model pressure orifice being checked is displayed on a gas-plasma terminal. On command, the program records up to 30 seconds of pressure data. After the recording is complete, the raw data and a straight line fit of the data are plotted on the terminal. This allows the technician to make a decision on the integrity of the orifice being checked. All results of the leak check program are stored in a database file that can be listed on the line printer for record keeping purposes or displayed on the terminal to help the technician find unchecked orifices. This program allows one technician to check a model for leaks instead of the two or three previously required.

Apparatus for integrated fuel assembly inspection system

International Nuclear Information System (INIS)

Ahmed, H.J.; Burchill, S.R.

1988-01-01

In a fuel assembly inspection apparatus, the combination is described comprising: (a) an elongated fixture mounted in a stationary upright position; (b) upper means mounted to an upper portion of the fixture and lower means mounted adjacent to a lower portion of the fixture, the upper and lower means being disposed outwardly from a side of the fixture for supporting a nuclear fuel assembly therebetween and extending along the side of the fixture; (c) a bottom carriage having a central opening adapted to receive the fuel assembly therethrough when supported between the upper and lower means such that the bottom carriage being connected only to, and extending in cantilever fashion outwardly from, the side of the fixture for generally vertical movement along the side of the fixture and along the fuel assembly extending along the side of the fixture; (d) drive means for selectively moving the bottom carriage; and (e) means disposed on the bottom carriage for measuring the envelop, of the fuel assembly when the bottom carriage is moved to and stationed at selected axial positions along the fuel assembly

Raman laser spectrometer optical head: qualification model assembly and integration verification

Science.gov (United States)

Ramos, G.; Sanz-Palomino, M.; Moral, A. G.; Canora, C. P.; Belenguer, T.; Canchal, R.; Prieto, J. A. R.; Santiago, A.; Gordillo, C.; Escribano, D.; Lopez-Reyes, G.; Rull, F.

2017-08-01

Raman Laser Spectrometer (RLS) is the Pasteur Payload instrument of the ExoMars mission, within the ESA's Aurora Exploration Programme, that will perform for the first time in an out planetary mission Raman spectroscopy. RLS is composed by SPU (Spectrometer Unit), iOH (Internal Optical Head), and ICEU (Instrument Control and Excitation Unit). iOH focuses the excitation laser on the samples (excitation path), and collects the Raman emission from the sample (collection path, composed on collimation system and filtering system). Its original design presented a high laser trace reaching to the detector, and although a certain level of laser trace was required for calibration purposes, the high level degrades the Signal to Noise Ratio confounding some Raman peaks. So, after the bread board campaign, some light design modifications were implemented in order to fix the desired amount of laser trace, and after the fabrication and the commitment of the commercial elements, the assembly and integration verification process was carried out. A brief description of the iOH design update for the engineering and qualification model (iOH EQM) as well as the assembly process are briefly described in this papers. In addition, the integration verification and the first functional tests, carried out with the RLS calibration target (CT), results are reported on.

Integrated Radiation Transport and Nuclear Fuel Performance for Assembly-Level Simulations

Energy Technology Data Exchange (ETDEWEB)

Clarno, Kevin T [ORNL; Hamilton, Steven P [ORNL; Philip, Bobby [ORNL; Berrill, Mark A [ORNL; Sampath, Rahul S [ORNL; Allu, Srikanth [ORNL; Pugmire, Dave [ORNL; Dilts, Gary [Los Alamos National Laboratory (LANL); Banfield, James E [ORNL

2012-02-01

The Advanced Multi-Physics (AMP) Nuclear Fuel Performance code (AMPFuel) is focused on predicting the temperature and strain within a nuclear fuel assembly to evaluate the performance and safety of existing and advanced nuclear fuel bundles within existing and advanced nuclear reactors. AMPFuel was extended to include an integrated nuclear fuel assembly capability for (one-way) coupled radiation transport and nuclear fuel assembly thermo-mechanics. This capability is the initial step toward incorporating an improved predictive nuclear fuel assembly modeling capability to accurately account for source-terms and boundary conditions of traditional (single-pin) nuclear fuel performance simulation, such as the neutron flux distribution, coolant conditions, and assembly mechanical stresses. A novel scheme is introduced for transferring the power distribution from the Scale/Denovo (Denovo) radiation transport code (structured, Cartesian mesh with smeared materials within each cell) to AMPFuel (unstructured, hexagonal mesh with a single material within each cell), allowing the use of a relatively coarse spatial mesh (10 million elements) for the radiation transport and a fine spatial mesh (3.3 billion elements) for thermo-mechanics with very little loss of accuracy. In addition, a new nuclear fuel-specific preconditioner was developed to account for the high aspect ratio of each fuel pin (12 feet axially, but 1 4 inches in diameter) with many individual fuel regions (pellets). With this novel capability, AMPFuel was used to model an entire 17 17 pressurized water reactor fuel assembly with many of the features resolved in three dimensions (for thermo-mechanics and/or neutronics), including the fuel, gap, and cladding of each of the 264 fuel pins; the 25 guide tubes; the top and bottom structural regions; and the upper and lower (neutron) reflector regions. The final, full assembly calculation was executed on Jaguar using 40,000 cores in under 10 hours to model over 162

Quality control of FWC during assembly/commissioning on SST-1

International Nuclear Information System (INIS)

Patel, Hiteshkumar; Santra, Prosenjit; Jaiswal, Snehal

2015-01-01

First Wall components (FWC) of SST-1 tokamak, which are in the immediate vicinity of plasma comprises of limiters, divertors, baffles, passive stabilizers are designed to operate long duration (1000 s) discharges of elongated plasma. All FWC consists of a copper alloy heat sink modules with SS cooling tubes brazed onto it, graphite tiles acting as armour material facing the plasma, and are mounted to the vacuum vessels with suitable Inconel support structures at ring and port locations. The FWC are very recently assembled and commissioned successfully inside the vacuum vessel of SST-1 under going a rigorous quality control and checks at every stage of the assembly process. This paper will present the quality control and checks of FWC from commencement of assembly procedure, namely material test reports, leak testing of high temperature baked components, assembled dimensional tolerances, leak testing of all welded joints, graphite tile tightening torques, electrical continuity of passive stabilizers, and electrical isolation of passive stabilizers from vacuum vessel, baking and cooling hydraulic connections inside vacuum vessel. (author)

CFD Analysis for Advanced Integrated Head Assembly

Energy Technology Data Exchange (ETDEWEB)

Jo, Won Ho; Kang, Tae Kyo; Cho, Yeon Ho; Kim, Hyun Min [KEPCO Engineering and Construction Co., Daejeon (Korea, Republic of)

2016-10-15

The Integrated Head Assembly (IHA) is permanently installed on the reactor vessel closure head during the normal plant operation and refueling operation. It consists of a number of systems and components such as the head lifting system, seismic support system, Control Element Drive Mechanism (CEDM) cooling system, cable support system, cooling shroud assemblies. With the operating experiences of the IHA, the needs for the design change to the current APR1400 IHA arouse to improve the seismic resistance and to accommodate the convenient maintenance. In this paper, the effects of the design changes were rigorously studied for the various sizes of the inlet openings to assure the proper cooling of the CEDMs. And the system pressure differentials and required flow rate for the CEDM cooling fan were analyzed regarding the various operating conditions for determining the capacity of the fan. As a part of the design process of the AIHA, the number of air inlets and baffle regions are reduced by simplifying the design of the APR1400 IHA. The design change of the baffle regions has been made such that the maximum possible space are occupied inside the IHA cooling shroud shell while avoiding the interference with CEDMs. So, only the air inlet opening was studied for the design change to supply a sufficient cooling air flow for each CEDM. The size and location of the air inlets in middle cooling shroud assembly were determined by the CFD analyses of the AIHA. And the case CFD analyses were performed depending on the ambient air temperature and fan operating conditions. The size of the air inlet openings is increased by comparison with the initial AIHA design, and it is confirmed that the cooling air flow rate for each CEDM meet the design requirement of 800 SCFM ± 10% with the increased air inlets. At the initial analysis, the fan outlet flow rate was assumed as 48.3 lbm/s, but the result revealed that the less outflow rate at the fan is enough to meet the design requirement

The Effects of Check-In, Check-Up, Check-Out for Students with Moderate Intellectual Disability during On- and Off-Site Vocational Training

Science.gov (United States)

Boden, Lauren J.; Jolivette, Kristine; Alberto, Paul A.

2018-01-01

Check-in/check-out is a secondary-tier intervention within the positive behavior interventions and supports framework. Check-in/check-out pairs the use of an adult mentor with a daily progress report to help students meet individualized behavioral goals. This study adds to the research base by examining the effects of check-in, check-up, check-out…

Regular health checks

DEFF Research Database (Denmark)

Grønhøj Larsen, Christian; Jørgensen, Karsten Juhl; Gøtzsche, Peter C

2012-01-01

To investigate whether Danish providers of general health checks present a balanced account of possible benefits and harms on their websites and whether the health checks are evidence-based.......To investigate whether Danish providers of general health checks present a balanced account of possible benefits and harms on their websites and whether the health checks are evidence-based....

Towards an automated checked baggage inspection system augmented with robots

Science.gov (United States)

DeDonato, Matthew P.; Dimitrov, Velin; Padır, Taskin

2014-05-01

We present a novel system for enhancing the efficiency and accuracy of checked baggage screening process at airports. The system requirements address the identification and retrieval of objects of interest that are prohibited in a checked luggage. The automated testbed is comprised of a Baxter research robot designed by Rethink Robotics for luggage and object manipulation, and a down-looking overhead RGB-D sensor for inspection and detection. We discuss an overview of current system implementations, areas of opportunity for improvements, robot system integration challenges, details of the proposed software architecture and experimental results from a case study for identifying various kinds of lighters in checked bags.

Checking Java Programs

CERN Document Server

Darwin, Ian

2007-01-01

This Short Cut tells you about tools that will improve the quality of your Java code, using checking above and beyond what the standard tools do, including: Using javac options, JUnit and assertions Making your IDE work harder Checking your source code with PMD Checking your compiled code (.class files) with FindBugs Checking your program's run-time behavior with Java PathFinder

Integrating community assembly and biodiversity to better understand ecosystem function: the Community Assembly and the Functioning of Ecosystems (CAFE) approach.

Science.gov (United States)

Bannar-Martin, Katherine H; Kremer, Colin T; Ernest, S K Morgan; Leibold, Mathew A; Auge, Harald; Chase, Jonathan; Declerck, Steven A J; Eisenhauer, Nico; Harpole, Stanley; Hillebrand, Helmut; Isbell, Forest; Koffel, Thomas; Larsen, Stefano; Narwani, Anita; Petermann, Jana S; Roscher, Christiane; Cabral, Juliano Sarmento; Supp, Sarah R

2018-02-01

The research of a generation of ecologists was catalysed by the recognition that the number and identity of species in communities influences the functioning of ecosystems. The relationship between biodiversity and ecosystem functioning (BEF) is most often examined by controlling species richness and randomising community composition. In natural systems, biodiversity changes are often part of a bigger community assembly dynamic. Therefore, focusing on community assembly and the functioning of ecosystems (CAFE), by integrating both species richness and composition through species gains, losses and changes in abundance, will better reveal how community changes affect ecosystem function. We synthesise the BEF and CAFE perspectives using an ecological application of the Price equation, which partitions the contributions of richness and composition to function. Using empirical examples, we show how the CAFE approach reveals important contributions of composition to function. These examples show how changes in species richness and composition driven by environmental perturbations can work in concert or antagonistically to influence ecosystem function. Considering how communities change in an integrative fashion, rather than focusing on one axis of community structure at a time, will improve our ability to anticipate and predict changes in ecosystem function. © 2017 The Authors. Ecology Letters published by CNRS and John Wiley & Sons Ltd.

Titanium dioxide nanowire sensor array integration on CMOS platform using deterministic assembly.

Science.gov (United States)

Gall, Oren Z; Zhong, Xiahua; Schulman, Daniel S; Kang, Myungkoo; Razavieh, Ali; Mayer, Theresa S

2017-06-30

Nanosensor arrays have recently received significant attention due to their utility in a wide range of applications, including gas sensing, fuel cells, internet of things, and portable health monitoring systems. Less attention has been given to the production of sensor platforms in the μW range for ultra-low power applications. Here, we discuss how to scale the nanosensor energy demand by developing a process for integration of nanowire sensing arrays on a monolithic CMOS chip. This work demonstrates an off-chip nanowire fabrication method; subsequently nanowires link to a fused SiO 2 substrate using electric-field assisted directed assembly. The nanowire resistances shown in this work have the highest resistance uniformity reported to date of 18%, which enables a practical roadmap towards the coupling of nanosensors to CMOS circuits and signal processing systems. The article also presents the utility of optimizing annealing conditions of the off-chip metal-oxides prior to CMOS integration to avoid limitations of thermal budget and process incompatibility. In the context of the platform demonstrated here, directed assembly is a powerful tool that can realize highly uniform, cross-reactive arrays of different types of metal-oxide nanosensors suited for gas discrimination and signal processing systems.

Compliant heterogeneous assemblies of micro-VCSELs as a new materials platform for integrated optoelectronics

Science.gov (United States)

Kang, Dongseok; Lee, Sung-Min; Kwong, Anthony; Yoon, Jongseung

2015-03-01

Despite many unique advantages, vertical cavity surface emitting lasers (VCSELs) have been available mostly on rigid, planar wafers over restricted areas, thereby limiting their usage for applications that can benefit from large-scale, programmable assemblies, hybrid integration with dissimilar materials and devices, or mechanically flexible constructions. Here, materials design and fabrication strategies that address these limitations of conventional VCSELs are presented. Specialized design of epitaxial materials and etching processes, together with printing-based deterministic assemblies and substrate thermal engineering, enabled defect-free release of microscale VCSELs and their device- and circuit-level implementation on non-native, flexible substrates with performance comparable to devices on the growth substrate.

Sequential induction of three recombination directionality factors directs assembly of tripartite integrative and conjugative elements.

Science.gov (United States)

Haskett, Timothy L; Terpolilli, Jason J; Ramachandran, Vinoy K; Verdonk, Callum J; Poole, Phillip S; O'Hara, Graham W; Ramsay, Joshua P

2018-03-01

Tripartite integrative and conjugative elements (ICE3) are a novel form of ICE that exist as three separate DNA regions integrated within the genomes of Mesorhizobium spp. Prior to conjugative transfer the three ICE3 regions of M. ciceri WSM1271 ICEMcSym1271 combine and excise to form a single circular element. This assembly requires three coordinated recombination events involving three site-specific recombinases IntS, IntG and IntM. Here, we demonstrate that three excisionases-or recombination directionality factors-RdfS, RdfG and RdfM are required for ICE3 excision. Transcriptome sequencing revealed that expression of ICE3 transfer and conjugation genes was induced by quorum sensing. Quorum sensing activated expression of rdfS, and in turn RdfS stimulated transcription of both rdfG and rdfM. Therefore, RdfS acts as a "master controller" of ICE3 assembly and excision. The dependence of all three excisive reactions on RdfS ensures that ICE3 excision occurs via a stepwise sequence of recombination events that avoids splitting the chromosome into a non-viable configuration. These discoveries expose a surprisingly simple control system guiding molecular assembly of these novel and complex mobile genetic elements and highlight the diverse and critical functions of excisionase proteins in control of horizontal gene transfer.

Liaison concatenation – A method to obtain feasible assembly ...

Indian Academy of Sciences (India)

non-possible assembly sequences using liaison graph. In this paper a new ... Applications (CATIA) software is a user friendly CAD tool with the feasibility of .... to perform the contact analysis to check the possibility of interference. Table 5.

Experiment for Integrating Dutch 3d Spatial Planning and Bim for Checking Building Permits

Science.gov (United States)

van Berlo, L.; Dijkmans, T.; Stoter, J.

2013-09-01

This paper presents a research project in The Netherlands in which several SMEs collaborated to create a 3D model of the National spatial planning information. This 2D information system described in the IMRO data standard holds implicit 3D information that can be used to generate an explicit 3D model. The project realized a proof of concept to generate a 3D spatial planning model. The team used the model to integrate it with several 3D Building Information Models (BIMs) described in the open data standard Industry Foundation Classes (IFC). Goal of the project was (1) to generate a 3D BIM model from spatial planning information to be used by the architect during the early design phase, and (2) allow 3D checking of building permits. The team used several technologies like CityGML, BIM clash detection and GeoBIM to explore the potential of this innovation. Within the project a showcase was created with a part of the spatial plan from the city of The Hague. Several BIM models were integrated in the 3D spatial plan of this area. A workflow has been described that demonstrates the benefits of collaboration between the spatial domain and the AEC industry in 3D. The research results in a showcase with conclusions and considerations for both national and international practice.

Quality control of FWC during assembly and commissioning in SST-1 Tokamak

Science.gov (United States)

Patel, Hitesh; Santra, Prosenjit; Parekh, Tejas; Biswas, Prabal; Jayswal, Snehal; Chauhan, Pradeep; Paravastu, Yuvakiran; George, Siju; Semwal, Pratibha; Thankey, Prashant; Ramesh, Gattu; Prakash, Arun; Dhanani, Kalpesh; Raval, D. C.; Khan, Ziauddin; Pradhan, Subrata

2017-04-01

First Wall Components (FWC) of SST-1 tokamak, which are in the immediate vicinity of plasma, comprises of limiters, divertors, baffles, passive stabilizers designed to operate long duration (∼1000 s) discharges of elongated plasma. All FWC consist of copper alloy heat sink modules with SS cooling tubes brazed onto it, graphite tiles acting as armour material facing the plasma, and are mounted to the vacuum vessels with suitable Inconel support structures at inter-connected ring & port locations. The FWC are very recently assembled and commissioned successfully inside the vacuum vessel of SST-1 undergoing a rigorous quality control and checks at every stage of the assembly process. This paper will present the quality control aspects and checks of FWC from commencement of assembly procedure, namely material test reports, leak testing of high temperature baked components, assembled dimensional tolerances, leak testing of all welded joints, graphite tile tightening torques, electrical continuity and electrical isolation of passive stabilizers from vacuum vessel, baking and cooling hydraulic connections inside vacuum vessel.

14 CFR 121.411 - Qualifications: Check airmen (airplane) and check airmen (simulator).

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Qualifications: Check airmen (airplane) and... § 121.411 Qualifications: Check airmen (airplane) and check airmen (simulator). (a) For the purposes of this section and § 121.413: (1) A check airman (airplane) is a person who is qualified, and permitted...

Impact analysis of spent fuel jacket assemblies

International Nuclear Information System (INIS)

Aramayo, G.A.

1994-01-01

As part of the analyses performed in support of the reracking of the High Flux Isotope Reactor pool, it became necessary to prove the structural integrity of the spent fuel jacket assemblies subjected to gravity drop that result from postulated accidents associated with the handling of these assemblies while submerged in the pool. The spent fuel jacket assemblies are an integral part of the reracking project, and serve to house fuel assemblies. The structure integrity of the jacket assemblies from loads that result from impact from a height of 10 feet onto specified targets has been performed analytically using the computer program LS-DYNA3D. Nine attitudes of the assembly at the time of impact have been considered. Results of the analyses show that there is no failure of the assemblies as a result of the impact scenarios considered

Heterogeneous MEMS device assembly and integration

Science.gov (United States)

Topart, Patrice; Picard, Francis; Ilias, Samir; Alain, Christine; Chevalier, Claude; Fisette, Bruno; Paultre, Jacques E.; Généreux, Francis; Legros, Mathieu; Lepage, Jean-François; Laverdière, Christian; Ngo Phong, Linh; Caron, Jean-Sol; Desroches, Yan

2014-03-01

In recent years, smart phone applications have both raised the pressure for cost and time to market reduction, and the need for high performance MEMS devices. This trend has led the MEMS community to develop multi-die packaging of different functionalities or multi-technology (i.e. wafer) approaches to fabricate and assemble devices respectively. This paper reports on the fabrication, assembly and packaging at INO of various MEMS devices using heterogeneous assembly at chip and package-level. First, the performance of a giant (e.g. about 3 mm in diameter), electrostatically actuated beam steering mirror is presented. It can be rotated about two perpendicular axes to steer an optical beam within an angular cone of up to 60° in vector scan mode with an angular resolution of 1 mrad and a response time of 300 ms. To achieve such angular performance relative to mirror size, the microassembly was performed from sub-components fabricated from 4 different wafers. To combine infrared detection with inertial sensing, an electroplated proof mass was flip-chipped onto a 256×1 pixel uncooled bolometric FPA and released using laser ablation. In addition to the microassembly technology, performance results of packaged devices are presented. Finally, to simulate a 3072×3 pixel uncooled detector for cloud and fire imaging in mid and long-wave IR, the staggered assembly of six 512×3 pixel FPAs with a less than 50 micron pixel co-registration is reported.

Assembly and integration of geo-scientific knowledge and arguments

International Nuclear Information System (INIS)

Gierszewki, P.; Gautschi, A.; Nguyen, T.S.; Laaksohaju, M.; Rohlig, K.J.; Peake, T.; Peltier, R.; Pitkanen, P.; Skagius Elert, K.; Sykes, J.F.

2007-01-01

The purpose of this working group was to consider the assembly and integration of geo-scientific knowledge and arguments. In an introductory presentation, K. Skagius Elert presented 'Assessment of Uncertainty and Confidence in Site Descriptive Models Experience from the On-going Site Investigation Programme in Sweden'. The detailed description of concepts and procedures established at SKB for the development of a Site Descriptive Model (SDM) provided a starting point for the discussion of the working group. The SDM components and the procedures to achieve them were used as 'references' for the discussion of comparable elements in other national programmes. The observations have been placed into two broad themes: 1. How to manage the integration? 2. How to handle uncertainties? No specific prescription was identified for either of these questions; rather a range of suggestions were noted based on experience. The appropriate solution will depend on the organisation, the site, the state of the programme, and other factors. A final observation from the working group was on the handling of evolution of the site with time. This topic incorporates aspects of both site integration and uncertainty management. Specifically, the integrated site description model (SDM) noted above represents a description of the site as it presently exists. This description takes into account the site history, but does not describe its evolution. The latter involves a number of uncertainties. This time evolution of the site can be described through Scenarios. The definition of scenarios, similar to the definition of the SDM, is an integrated and multidisciplinary process in order to ensure a self-consistent description. It will involve use of common assumptions. Since it involves the future and the associated uncertainties, it can be useful to draw on expert panels to help define the key assumptions and outlines for scenarios. (authors)

Study of the Electrolytic Reduction of Uranium Oxide in LiCl-Li2O Molten Salts with an Integrated Cathode Assembly

International Nuclear Information System (INIS)

Park, Sung Bin; Seo, Chung Seok; Kang, Dae Seung; Kwon, Seon Gil; Park, Seong Won

2005-01-01

The electrolytic reduction of uranium oxide in a LiCl-Li 2 O molten salt system has been studied in a 10 g U 3 O 3 /batch-scale experimental apparatus with an integrated cathode assembly at 650 .deg. C. The integrated cathode assembly consists of an electric conductor, the uranium oxide to be reduced and the membrane for loading the uranium oxide. From the cyclic voltammograms for the LiCl-3 wt% Li 3 O system and the U 3 O 3 -LiCl-3 wt% Li 2 O system according to the materials of the membrane in the cathode assembly, the mechanisms of the predominant reduction reactions in the electrolytic reactor cell were to be understood; direct and indirect electrolytic reduction of uranium oxide. Direct and indirect electrolytic reductions have been performed with the integrated cathode assembly. Using the 325-mesh stainless steel screen the uranium oxide failed to be reduced to uranium metal by a direct and indirect electrolytic reduction because of a low current efficiency and with the porous magnesia membrane the uranium oxide was reduced successfully to uranium metal by an indirect electrolytic reduction because of a high current efficiency.

Optimization of Two-Level Disassembly/Remanufacturing/Assembly System with an Integrated Maintenance Strategy

Directory of Open Access Journals (Sweden)

Zouhour Guiras

2018-04-01

Full Text Available With an increase of environmental pressure on economic activities, reverse flow is increasingly important. It seeks to save resources, eliminate waste, and improve productivity. This paper investigates the optimization of the disassembly, remanufacturing and assembly system, taking into account assembly-disassembly system degradation. An analytical model is developed to consider disassembly, remanufacturing of used/end-of-life product and assembly of the finished product. The finished product is composed of remanufactured and new components. A maintenance policy is sequentially integrated to reduce the system unavailability. The aim of this study is to help decision-makers, under certain conditions, choose the most cost-effective process for them to satisfy the customer as well as to adapt to the potential risk that can perturb the disassembly-assembly system. A heuristic is developed to determine the optimal ordered date of the used end-of-life product as well as the optimum release dates of new external components. The results reveal that considering some remanufacturing and purchase components costs, the proposed model is more economical in comparison with a model without remanufactured parts. Numerical results are provided to illustrate the impact of the variation of the ordering cost and quality of the used end-of-life product on the system profitability. Finally, the risk due to system repair periods is discussed, which has an impact on managerial decision-making.

Fuel Assembly Damping Summary

Energy Technology Data Exchange (ETDEWEB)

Lee, Kanghee; Kang, Heungseok; Oh, Dongseok; Yoon, Kyungho; Kim, Hyungkyu; Kim, Jaeyong [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2013-10-15

This paper summary the fuel assembly damping data in air/in still water/under flow, released from foreign fuel vendors, compared our data with the published data. Some technical issues in fuel assembly damping measurement testing are also briefly discussed. Understanding of each fuel assembly damping mechanisms according to the surrounding medium and flow velocity can support the fuel design improvement in fuel assembly dynamics and structural integrity aspect. Because the upgraded requirements of the newly-developed advanced reactor system will demands to minimize fuel design margin in integrity evaluation, reduction in conservatism of fuel assembly damping can contribute to alleviate the fuel design margin for sure. Damping is an energy dissipation mechanism in a vibrating mechanical structure and prevents a resonant structure from having infinite vibration amplitudes. The sources of fuel assembly damping are various from support friction to flow contribution, and it can be increased by the viscosity or drag of surrounding fluid medium or the average velocity of water flowing. Fuel licensing requires fuel design evaluation in transient or accidental condition. Dynamic response analysis of fuel assembly is to show fuel integrity and requires information on assembly-wise damping in dry condition and under wet or water flowing condition. However, damping measurement test for the full-scale fuel assembly prototype is not easy to carry out because of the scale (fuel prototype, test facility), unsteadiness of test data (scattering, random sampling and processing), instrumentation under water flowing (water-proof response measurement), and noise. LWR fuel technology division in KAERI is preparing the infra structure for damping measurement test of full-scale fuel assembly, to support fuel industries and related research activities. Here is a preliminary summary of fuel assembly damping, published in the literature. Some technical issues in fuel assembly damping

Intelligent Data Visualization for Cross-Checking Spacecraft System Diagnosis

Science.gov (United States)

Ong, James C.; Remolina, Emilio; Breeden, David; Stroozas, Brett A.; Mohammed, John L.

2012-01-01

Any reasoning system is fallible, so crew members and flight controllers must be able to cross-check automated diagnoses of spacecraft or habitat problems by considering alternate diagnoses and analyzing related evidence. Cross-checking improves diagnostic accuracy because people can apply information processing heuristics, pattern recognition techniques, and reasoning methods that the automated diagnostic system may not possess. Over time, cross-checking also enables crew members to become comfortable with how the diagnostic reasoning system performs, so the system can earn the crew s trust. We developed intelligent data visualization software that helps users cross-check automated diagnoses of system faults more effectively. The user interface displays scrollable arrays of timelines and time-series graphs, which are tightly integrated with an interactive, color-coded system schematic to show important spatial-temporal data patterns. Signal processing and rule-based diagnostic reasoning automatically identify alternate hypotheses and data patterns that support or rebut the original and alternate diagnoses. A color-coded matrix display summarizes the supporting or rebutting evidence for each diagnosis, and a drill-down capability enables crew members to quickly view graphs and timelines of the underlying data. This system demonstrates that modest amounts of diagnostic reasoning, combined with interactive, information-dense data visualizations, can accelerate system diagnosis and cross-checking.

Sequential induction of three recombination directionality factors directs assembly of tripartite integrative and conjugative elements.

Directory of Open Access Journals (Sweden)

Timothy L Haskett

2018-03-01

Full Text Available Tripartite integrative and conjugative elements (ICE3 are a novel form of ICE that exist as three separate DNA regions integrated within the genomes of Mesorhizobium spp. Prior to conjugative transfer the three ICE3 regions of M. ciceri WSM1271 ICEMcSym1271 combine and excise to form a single circular element. This assembly requires three coordinated recombination events involving three site-specific recombinases IntS, IntG and IntM. Here, we demonstrate that three excisionases-or recombination directionality factors-RdfS, RdfG and RdfM are required for ICE3 excision. Transcriptome sequencing revealed that expression of ICE3 transfer and conjugation genes was induced by quorum sensing. Quorum sensing activated expression of rdfS, and in turn RdfS stimulated transcription of both rdfG and rdfM. Therefore, RdfS acts as a "master controller" of ICE3 assembly and excision. The dependence of all three excisive reactions on RdfS ensures that ICE3 excision occurs via a stepwise sequence of recombination events that avoids splitting the chromosome into a non-viable configuration. These discoveries expose a surprisingly simple control system guiding molecular assembly of these novel and complex mobile genetic elements and highlight the diverse and critical functions of excisionase proteins in control of horizontal gene transfer.

Engineering within the assembly, verification, and integration (AIV) process in ALMA

Science.gov (United States)

Lopez, Bernhard; McMullin, Joseph P.; Whyborn, Nicholas D.; Duvall, Eugene

2010-07-01

The Atacama Large Millimeter/submillimeter Array (ALMA) is a joint project between astronomical organizations in Europe, North America, and East Asia, in collaboration with the Republic of Chile. ALMA will consist of at least 54 twelve-meter antennas and 12 seven-meter antennas operating as an interferometer in the millimeter and sub-millimeter wavelength range. It will be located at an altitude above 5000m in the Chilean Atacama desert. As part of the ALMA construction phase the Assembly, Verification and Integration (AIV) team receives antennas and instrumentation from Integrated Product Teams (IPTs), verifies that the sub-systems perform as expected, performs the assembly and integration of the scientific instrumentation and verifies that functional and performance requirements are met. This paper aims to describe those aspects related to the AIV Engineering team, its role within the 4-station AIV process, the different phases the group underwent, lessons learned and potential space for improvement. AIV Engineering initially focused on the preparation of the necessary site infrastructure for AIV activities, on the purchase of tools and equipment and on the first ALMA system installations. With the first antennas arriving on site the team started to gather experience with AIV Station 1 beacon holography measurements for the assessment of the overall antenna surface quality, and with optical pointing to confirm the antenna pointing and tracking capabilities. With the arrival of the first receiver AIV Station 2 was developed which focuses on the installation of electrical and cryogenic systems and incrementally establishes the full connectivity of the antenna as an observing platform. Further antenna deliveries then allowed to refine the related procedures, develop staff expertise and to transition towards a more routine production process. Stations 3 and 4 deal with verification of the antenna with integrated electronics by the AIV Science Team and is not covered

Integration of micro nano and bio technologies with layer-by-layer self-assembly

Science.gov (United States)

Kommireddy, Dinesh Shankar

In the past decade, layer-by-layer (LbL) nanoassembly has been used as a tool for immobilization and surface modification of materials with applications in biology and physical sciences. Often, in such applications, LbL assembly is integrated with various techniques to form functional surface coatings and immobilized matrices. In this work, integration of LbL with microfabrication and microfluidics, and tissue engineering are explored. In an effort to integrate microfabrication with LbL nanoassembly, microchannels were fabricated using soft-lithography and the surface of these channels was used for the immobilization of materials using LbL and laminar flow patterning. Synthesis of poly(dimethyldiallyl ammonium chloride)/poly(styrene sulfonate) and poly(dimethyldiallyl ammonium chloride)/bovine serum albumin microstrips is demonstrated with the laminar flow microfluidic reactor. Resulting micropatterns are 8-10 mum wide, separated with few micron gaps. The width of these microstrips as well as their position in the microchannel is controlled by varying the flow rate, time of interaction and concentration of the individual components, which is verified by numerical simulation. Spatially resolved pH sensitivity was observed by modifying the surface of the channel with a pH sensitive dye. In order to investigate the integration of LbL assembly with tissue engineering, glass substrates were coated with nanoparticle/polyelectrolyte layers, and two different cell types were used to test the applicability of these coatings for the surface modification of medical implants. Titanium dioxide (TiO 2), silicon dioxide, halloysite and montmorillonite nanoparticles were assembled with oppositely charged polyelectrolytes. In-vitro cytotoxicity tests of the nanoparticle substrates on human dermal firbroblasts (HDFs) showed that the nanoparticle surfaces do not have toxic effects on the cells. HDFs retained their phenotype on the nanoparticle coatings, by synthesizing type

14 CFR 91.1089 - Qualifications: Check pilots (aircraft) and check pilots (simulator).

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 2 2010-01-01 2010-01-01 false Qualifications: Check pilots (aircraft) and check pilots (simulator). 91.1089 Section 91.1089 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... RULES Fractional Ownership Operations Program Management § 91.1089 Qualifications: Check pilots...

Design of an integral missile shield in integrated head assembly for pressurized water reactor at commercial nuclear plants

International Nuclear Information System (INIS)

Baliga, Ravi; Watts, Tom Neal; Kamath, Harish

2015-01-01

In ICONE22, the authors presented the Integrated Head Assembly (IHA) design concept implemented at Callaway Nuclear Power Plant in Missouri, USA. The IHA concept is implemented to reduce the outage duration and the associated radiation exposure to the workers by reducing critical path time during Plant Refueling Outage. One of the head area components in the IHA is a steel missile shield designed to protect the Control Rod Drive Mechanism (CRDM) assembly from damaging other safety-related components in the vicinity in the Containment. Per Federally implemented General Design Criteria for commercial nuclear plants in the USA, the design of Nuclear Steam Supply System (NSSS) must provide protection from the damages caused by a postulated event of CRDM housing units and their associated parts disengaging from the reactor vessel assembly. This event is considered as a Loss of Coolant Accident (LOCA) and assumes that once the CRDM housing unit and their associated parts disengage from the reactor vessel internals assembly, they travel upward by the water jet with the following sequence of events: Per Reference 1, the drive shaft and control rod cluster are forced out of the reactor core by the differential pressure across the drive shaft with the assumption that the drive shaft and control rod cluster, latched together, are fully inserted when the accident occurs. After the travel, the rod cluster control spider will impact the lower side of the upper support plate inside the reactor vessel fracturing the flexure arms in the joint freeing the drive shaft from the control rod cluster. The control rod cluster is stopped by the upper support plate and will remain below the upper support plate during this accident. However, the drive shaft will continue to accelerate in the upward direction until it is stopped by a safety feature in the IHA. The integral missile shield as a safety feature in the IHA is designed to stop the CRDM drive shaft from moving further up in the

Overview of Prevention for Water Hammer by Check Valve Action in Nuclear Reactor

International Nuclear Information System (INIS)

Kim, Dayong; Yoon, Hyungi; Seo, Kyoungwoo; Kim, Seonhoon

2016-01-01

Water hammer can cause serious damage to pumping system and unexpected system pressure rise in the pipeline. In nuclear reactor, water hammer can influence on the integrity of safety related system. Water hammer in nuclear reactor have been caused by voiding in normally water-filled lines, steam condensation line containing both steam and water, as well as by rapid check valve action. Therefore, this study focuses on the water hammer by check valve among the sources of water hammer occurrence and suggests proper methodology for check valve type selection against water hammer. This study focuses on the water hammer by check valve action among the sources of water hammer occurrence and suggests proper methodology for check valve type selection against water hammer. If the inadvertent pump trip or pipe rupture in high velocity and pressure pipe is predicted, the fast response check valve such as tiled disc, dual disc and nozzle check valve should be installed in the system. If the inadvertent pump trip or pipe rupture in very high velocity and pressure pipe and excessively large revered flow velocity are predicted, the very slowly closing check valve such as controlled closure check valve should be installed in the system

Overview of Prevention for Water Hammer by Check Valve Action in Nuclear Reactor

Energy Technology Data Exchange (ETDEWEB)

Kim, Dayong; Yoon, Hyungi; Seo, Kyoungwoo; Kim, Seonhoon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

Water hammer can cause serious damage to pumping system and unexpected system pressure rise in the pipeline. In nuclear reactor, water hammer can influence on the integrity of safety related system. Water hammer in nuclear reactor have been caused by voiding in normally water-filled lines, steam condensation line containing both steam and water, as well as by rapid check valve action. Therefore, this study focuses on the water hammer by check valve among the sources of water hammer occurrence and suggests proper methodology for check valve type selection against water hammer. This study focuses on the water hammer by check valve action among the sources of water hammer occurrence and suggests proper methodology for check valve type selection against water hammer. If the inadvertent pump trip or pipe rupture in high velocity and pressure pipe is predicted, the fast response check valve such as tiled disc, dual disc and nozzle check valve should be installed in the system. If the inadvertent pump trip or pipe rupture in very high velocity and pressure pipe and excessively large revered flow velocity are predicted, the very slowly closing check valve such as controlled closure check valve should be installed in the system.

Characteristics of an integrated cathode assembly for the electrolytic reduction of uranium oxide in a LiCl-Li2O molten salt

International Nuclear Information System (INIS)

Sung Bin Park; Byung Heung Park; Sang Mun Jeong; Jin Mok Hur; Chung Seok Seo; Seong Won Park; Seung-Hoon Choi

2006-01-01

Electrochemical behavior of the reduction of uranium oxide was studied in a LiCl-Li 2 O molten salt system with an integrated cathode assembly. The mechanism for the electrolytic reduction of uranium oxide was studied through cyclic voltammetry. By means of a chronopotentiometry, the effects of the thickness of the uranium oxide, the thickness of the MgO membrane and the material of the conductor of an integrated cathode assembly on the overpotential of the cathode were investigated. From the voltamograms, the reduction potential of the uranium oxide and Li 2 O was obtained and the two mechanisms of the electrolytic reduction were considered with regard to the applied cathode potential. From the chronopotentiograms, the exchange current, the transfer coefficient and the maximum allowable current based on the Tafel behavior were obtained with regard to the thickness of the uranium oxide, and of the MgO membrane and the material of the conductor of an integrated cathode assembly. (author)

Hierarchical remote data possession checking method based on massive cloud files

Directory of Open Access Journals (Sweden)

Ma Haifeng

2017-06-01

Full Text Available Cloud storage service enables users to migrate their data and applications to the cloud, which saves the local data maintenance and brings great convenience to the users. But in cloud storage, the storage servers may not be fully trustworthy. How to verify the integrity of cloud data with lower overhead for users has become an increasingly concerned problem. Many remote data integrity protection methods have been proposed, but these methods authenticated cloud files one by one when verifying multiple files. Therefore, the computation and communication overhead are still high. Aiming at this problem, a hierarchical remote data possession checking (hierarchical-remote data possession checking (H-RDPC method is proposed, which can provide efficient and secure remote data integrity protection and can support dynamic data operations. This paper gives the algorithm descriptions, security, and false negative rate analysis of H-RDPC. The security analysis and experimental performance evaluation results show that the proposed H-RDPC is efficient and reliable in verifying massive cloud files, and it has 32–81% improvement in performance compared with RDPC.

Robotically Assembled Aerospace Structures: Digital Material Assembly using a Gantry-Type Assembler

Science.gov (United States)

Trinh, Greenfield; Copplestone, Grace; O'Connor, Molly; Hu, Steven; Nowak, Sebastian; Cheung, Kenneth; Jenett, Benjamin; Cellucci, Daniel

2017-01-01

This paper evaluates the development of automated assembly techniques for discrete lattice structures using a multi-axis gantry type CNC machine. These lattices are made of discrete components called "digital materials." We present the development of a specialized end effector that works in conjunction with the CNC machine to assemble these lattices. With this configuration we are able to place voxels at a rate of 1.5 per minute. The scalability of digital material structures due to the incremental modular assembly is one of its key traits and an important metric of interest. We investigate the build times of a 5x5 beam structure on the scale of 1 meter (325 parts), 10 meters (3,250 parts), and 30 meters (9,750 parts). Utilizing the current configuration with a single end effector, performing serial assembly with a globally fixed feed station at the edge of the build volume, the build time increases according to a scaling law of n4, where n is the build scale. Build times can be reduced significantly by integrating feed systems into the gantry itself, resulting in a scaling law of n3. A completely serial assembly process will encounter time limitations as build scale increases. Automated assembly for digital materials can assemble high performance structures from discrete parts, and techniques such as built in feed systems, parallelization, and optimization of the fastening process will yield much higher throughput.

TPX assembly plan

International Nuclear Information System (INIS)

Knutson, D.

1993-01-01

The TPX machine will be assembled in the TFTR Test Cell at the Plasma Physics Laboratory, utilizing the existing TFTR machine foundation. Preparation of the area for assembly will begin after completion of the decontamination and decommissioning phase on TFTR and certification that the radiation levels remaining, if any, are consistent with the types of operations planned. Assembly operations begin with the arrival of the first components, and conclude, approximately 24 months later, with the successful completion of the integrated systems tests and the achievement of a first plasma

Assembly tool design

International Nuclear Information System (INIS)

Kanamori, Naokazu; Nakahira, Masataka; Ohkawa, Yoshinao; Tada, Eisuke; Seki, Masahiro

1996-06-01

The reactor core of the International Thermonuclear Experimental Reactor (ITER) is assembled with a number of large and asymmetric components within a tight tolerance in order to assure the structural integrity for various loads and to provide the tritium confinement. In addition, the assembly procedure should be compatible with remote operation since the core structures will be activated by 14-MeV neutrons once it starts operation and thus personal access will be prohibited. Accordingly, the assembly procedure and tool design are quite essential and should be designed from the beginning to facilitate remote operation. According to the ITER Design Task Agreement, the Japan Atomic Energy Research Institute (JAERI) has performed design study to develop the assembly procedures and associated tool design for the ITER tokamak assembly. This report describes outlines of the assembly tools and the remaining issues obtained in this design study. (author)

Experimental study of new generation WWER-1000 fuel assemblies at JSC NCCP

International Nuclear Information System (INIS)

Enin, A.; Rozhkov, V.; Sinikov, Y.; Ustimenko, A.; Shustov, M.

2003-01-01

An experimental program for the study of fuel assembly thermomechanical stability has been established together with RF SSC IPPE and Russian Scientific Center Kurchatov Institute. Assembly fragments and small dummy models of fuel assembly skeletons and fuel rod bundles have been used for the tests. The test results are used for the design selection, verification of the design codes and substantiation of operating capacity of fuel assemblies with a rigid skeleton. The mechanical characteristics of units make it possible to perform fuel assembly strength and rigidity calculations, including the cases of abnormal operation. The mechanical characteristics of the skeleton and fuel rod bundle dummy models make it possible to check for the adequacy of the fuel assembly design model. The mechanical characteristics obtained during fuel rods bundle push through experiments make it possible to substantiate the fuel assembly serviceability under the conditions of fuel rods bundle and skeleton interaction

Characterization of the Caliban and Prospero Critical Assemblies Neutron Spectra for Integral Measurements Experiments

Science.gov (United States)

Casoli, P.; Authier, N.; Jacquet, X.; Cartier, J.

2014-04-01

Caliban and Prospero are two highly enriched uranium metallic core reactors operated on the CEA Center of Valduc. These critical assemblies are suitable for integral experiments, such as fission yields measurements or perturbation measurements, which have been carried out recently on the Caliban reactor. Different unfolding methods, based on activation foils and fission chambers measurements, are used to characterize the reactor spectra and especially the Caliban spectrum, which is very close to a pure fission spectrum.

Target Assembly Facility

Data.gov (United States)

Federal Laboratory Consortium — The Target Assembly Facility integrates new armor concepts into actual armored vehicles. Featuring the capability ofmachining and cutting radioactive materials, it...

Burnable absorber-integrated Guide Thimble (BigT) - 1. Design concepts and neutronic characterization on the fuel assembly benchmarks

International Nuclear Information System (INIS)

Yahya, Mohd-Syukri; Yu, Hwanyeal; Kim, Yonghee

2016-01-01

This paper presents the conceptual designs of a new burnable absorber (BA) for the pressurized water reactor (PWR), which is named 'Burnable absorber-integrated Guide Thimble' (BigT). The BigT integrates BA materials into standard guide thimble in a PWR fuel assembly. Neutronic sensitivities and practical design considerations of the BigT concept are points of highlight in the first half of the paper. Specifically, the BigT concepts are characterized in view of its BA material and spatial self-shielding variations. In addition, the BigT replaceability requirement, bottom-end design specifications and thermal-hydraulic considerations are also deliberated. Meanwhile, much of the second half of the paper is devoted to demonstrate practical viability of the BigT absorbers via comparative evaluations against the conventional BA technologies in representative 17x17 and 16x16 fuel assembly lattices. For the 17x17 lattice evaluations, all three BigT variants are benchmarked against Westinghouse's existing BA technologies, while in the 16x16 assembly analyses, the BigT designs are compared against traditional integral gadolinia-urania rod design. All analyses clearly show that the BigT absorbers perform as well as the commercial BA technologies in terms of reactivity and power peaking management. In addition, it has been shown that sufficiently high control rod worth can be obtained with the BigT absorbers in place. All neutronic simulations were completed using the Monte Carlo Serpent code with ENDF/B-VII.0 library. (author)

Self assembly of organic nanostructures and dielectrophoretic assembly of inorganic nanowires.

Science.gov (United States)

Dholakia, Geetha; Kuo, Steven; Allen, E. L.

2007-03-01

Self assembly techniques enable the organization of organic molecules into nanostructures. Currently engineering strategies for efficient assembly and routine integration of inorganic nanoscale objects into functional devices is very limited. AC Dielectrophoresis is an efficient technique to manipulate inorganic nanomaterials into higher dimensional structures. We used an alumina template based sol-gel synthesis method for the growth of various metal oxide nanowires with typical diameters of 100-150 nm, ranging in length from 3-10 μm. Here we report the dielectrophoretic assembly of TiO2 nanowires, an important material for photocatalysis and photovoltaics, onto interdigitated devices. Self assembly in organic nanostructures and its dependence on structure and stereochemistry of the molecule and dielectrophoretic field dependence in the assembly of inorganic nanowires will be compared and contrasted. Tunneling spectroscopy and DOS of these nanoscale systems will also be discussed.

Efficient Integrity Checking for Databases with Recursive Views

DEFF Research Database (Denmark)

Martinenghi, Davide; Christiansen, Henning

2005-01-01

Efficient and incremental maintenance of integrity constraints involving recursive views is a difficult issue that has received some attention in the past years, but for which no widely accepted solution exists yet. In this paper a technique is proposed for compiling such integrity constraints in...... approaches have not achieved comparable optimization with the same level of generality....

Repeated checking causes memory distrust

NARCIS (Netherlands)

van den Hout, M.; Kindt, M.

2003-01-01

This paper attempts to explain why in obsessive-compulsive disorder (OCD) checkers distrust in memory persists despite extensive checking. It is argued that: (1) repeated checking increases familiarity with the issues checked; (2) increased familiarity promotes conceptual processing which inhibits

LEU WWR-M2 fuel assemblies burnable test

International Nuclear Information System (INIS)

Kirsanov, G.A.; Konoplev, K.A.; Pikulik, R.G.; Sajkov, Yu. P.; Tchmshkyan, D.V.; Tedoradze, L.V.; Zakharov, A.S.

2000-01-01

The results of in-pile irradiation tests of LEU WWR-M2 fuel assemblies with reduced enrichment of fuel are submitted in the report. The tests are made according to the Russian Program on Reduced Enrichment for Research and Test Reactors (RERTR). United States Department of Energy and the Ministry of Atomic Energy of Russian Federation jointly fund this Program. The irradiation tests of 5 WWR-M2 experimental assemblies are carried out at WWR-M reactor of the Petersburg Nuclear Physics Institute (PNPI). The information on assembly design and technique of irradiation tests is presented. In the irradiation tests the integrity of fuel assemblies is periodically measured. The report presents the data for the integrity maintained during the burnup of 5 fuel assemblies up to 45%. These results demonstrate the high reliability of the experimental fuel assemblies within the guaranteed burnup limits specified by the manufacturer. The tests are still in progress; it is planned to test and analyze the change in integrity for burnup of up to 70% - 75% or more. LEU WWR-M2 fuel assemblies are to be offered for export by their Novosibirsk manufacturer. Currently, HEU WWR-M2 fuel assemblies are used in Hungary, Ukraine and Vietnam. LEU WWR-M2 fuel assemblies were designed as a possible replacement for the HEU WWR-M2 fuel assemblies in those countries, but their use can be extended to other research reactors. (author)

Nuclear reactor seismic fuel assembly grid

International Nuclear Information System (INIS)

Anthony, A.J.

1977-01-01

The strength of a nuclear reactor fuel assembly is enhanced by increasing the crush strength of the zircaloy spacer grids which locate and support the fuel elements in the fuel assembly. Increased resistance to deformation as a result of laterally directed forces is achieved by increasing the section modulus of the perimeter strip through bending the upper and lower edges thereof inwardly. The perimeter strip is further rigidized by forming, in the central portion thereof, dimples which extend inwardly with respect to the fuel assembly. The integrity of the spacer grid may also be enhanced by providing back-up arches for some or all of the integral fuel element locating springs and the strength of the fuel assembly may be further enhanced by providing, intermediate its ends, a steel seismic grid. 13 claims, 6 figures

What is a good health check? An interview study of health check providers' views and practices.

Science.gov (United States)

Stol, Yrrah H; Asscher, Eva C A; Schermer, Maartje H N

2017-10-02

Health checks identify (risk factors for) disease in people without symptoms. They may be offered by the government through population screenings and by other providers to individual users as 'personal health checks'. Health check providers' perspective of 'good' health checks may further the debate on the ethical evaluation and possible regulation of these personal health checks. In 2015, we interviewed twenty Dutch health check providers on criteria for 'good' health checks, and the role these criteria play in their practices. Providers unanimously formulate a number of minimal criteria: Checks must focus on (risk factors for) treatable/preventable disease; Tests must be reliable and clinically valid; Participation must be informed and voluntary; Checks should provide more benefits than harms; Governmental screenings should be cost-effective. Aspirational criteria mentioned were: Follow-up care should be provided; Providers should be skilled and experienced professionals that put the benefit of (potential) users first; Providers should take time and attention. Some criteria were contested: People should be free to test on any (risk factor for) disease; Health checks should only be performed in people at high risk for disease that are likely to implement health advice; Follow up care of privately funded tests should not drain on collective resources. Providers do not always fulfil their own criteria. Their reasons reveal conflicts between criteria, conflicts between criteria and other ethical values, and point to components in the (Dutch) organisation of health care that hinder an ethical provision of health checks. Moreover, providers consider informed consent a criterion that is hard to establish in practice. According to providers, personal health checks should meet the same criteria as population screenings, with the exception of cost-effectiveness. Providers do not always fulfil their own criteria. Results indicate that in thinking about the ethics of health

Parallel Algorithms for Model Checking

NARCIS (Netherlands)

van de Pol, Jaco; Mousavi, Mohammad Reza; Sgall, Jiri

2017-01-01

Model checking is an automated verification procedure, which checks that a model of a system satisfies certain properties. These properties are typically expressed in some temporal logic, like LTL and CTL. Algorithms for LTL model checking (linear time logic) are based on automata theory and graph

FAID/SPAR field tests at Kahl: A final report

International Nuclear Information System (INIS)

McKenzie, J.M.; Self, B.G.; Crawford, T.J.; Suber, L.A.

1986-01-01

LWR fuel assemblies are convenient units for item accounting. A pplication of a fuel assembly seal which gives both integrity and a unique identity to the fuel assembly offers the potential of increased safeguards over present methods. This is particularly the case if the seal can be read at frequent intervals. The BWR Kahl reactor has been used to field evaluate FAID type ultrasonic seals. Twenty-four seals were applied to fresh fuel assemblies before their being placed in the reactor core. At convenient times when the reactor was shut down and the fuel moved to the spent fuel storage pool, the seal's identity and integrity were checked with a seal pattern reader (SPAR). After the reactor was decommissioned all seals were reidentified and their integrity checked. Five seals were removed from their fuel assemblies and embrittlement of the fracture link observed. Several seals were in the reactor core for three years

Human Assisted Assembly Processes

Energy Technology Data Exchange (ETDEWEB)

CALTON,TERRI L.; PETERS,RALPH R.

2000-01-01

Automatic assembly sequencing and visualization tools are valuable in determining the best assembly sequences, but without Human Factors and Figure Models (HFFMs) it is difficult to evaluate or visualize human interaction. In industry, accelerating technological advances and shorter market windows have forced companies to turn to an agile manufacturing paradigm. This trend has promoted computerized automation of product design and manufacturing processes, such as automated assembly planning. However, all automated assembly planning software tools assume that the individual components fly into their assembled configuration and generate what appear to be a perfectly valid operations, but in reality the operations cannot physically be carried out by a human. Similarly, human figure modeling algorithms may indicate that assembly operations are not feasible and consequently force design modifications; however, if they had the capability to quickly generate alternative assembly sequences, they might have identified a feasible solution. To solve this problem HFFMs must be integrated with automated assembly planning to allow engineers to verify that assembly operations are possible and to see ways to make the designs even better. Factories will very likely put humans and robots together in cooperative environments to meet the demands for customized products, for purposes including robotic and automated assembly. For robots to work harmoniously within an integrated environment with humans the robots must have cooperative operational skills. For example, in a human only environment, humans may tolerate collisions with one another if they did not cause much pain. This level of tolerance may or may not apply to robot-human environments. Humans expect that robots will be able to operate and navigate in their environments without collisions or interference. The ability to accomplish this is linked to the sensing capabilities available. Current work in the field of cooperative

Biomedical Applications of Self-Assembling Peptides

NARCIS (Netherlands)

Radmalekshahi, Mazda; Lempsink, Ludwijn; Amidi, Maryam; Hennink, Wim E.; Mastrobattista, Enrico

2016-01-01

Self-assembling peptides have gained increasing attention as versatile molecules to generate diverse supramolecular structures with tunable functionality. Because of the possibility to integrate a wide range of functional domains into self-assembling peptides including cell attachment sequences,

Assembly and Integration Process of the First High Density Detector Array for the Atacama Cosmology Telescope

Science.gov (United States)

Li, Yaqiong; Choi, Steve; Ho, Shuay-Pwu; Crowley, Kevin T.; Salatino, Maria; Simon, Sara M.; Staggs, Suzanne T.; Nati, Federico; Wollack, Edward J.

2016-01-01

The Advanced ACTPol (AdvACT) upgrade on the Atacama Cosmology Telescope (ACT) consists of multichroicTransition Edge Sensor (TES) detector arrays to measure the Cosmic Microwave Background (CMB) polarization anisotropies in multiple frequency bands. The first AdvACT detector array, sensitive to both 150 and 230 GHz, is fabricated on a 150 mm diameter wafer and read out with a completely different scheme compared to ACTPol. Approximately 2000 TES bolometers are packed into the wafer leading to both a much denser detector density and readout circuitry. The demonstration of the assembly and integration of the AdvACT arrays is important for the next generation CMB experiments, which will continue to increase the pixel number and density. We present the detailed assembly process of the first AdvACT detector array.

Check valves aging assessment

International Nuclear Information System (INIS)

Haynes, H.D.

1991-01-01

In support of the NRC Nuclear Plant Aging Research (NPAR) program, the Oak Ridge National Laboratory (ORNL) has carried out an assessment of several check value diagnostic monitoring methods, in particular, those based on measurements of acoustic emission, ultrasonics, and magnetic flux. The evaluations have focussed on the capabilities of each method to provide information useful in determining check valve aging and service wear effects, check valve failures, and undesirable operating modes. This paper describes the benefits and limitations associated with each method and includes recent laboratory and field test data, including data obtained from the vendors who recently participated in a comprehensive series of tests directed by a nuclear industry users group. In addition, as part of the ORNL Advanced Diagnostic Engineering Research and Development Center (ADEC), two novel nonintrusive monitoring methods were developed that provide several unique capabilities. These methods, based on external ac- an dc-magnetic monitoring are also described. None of the examined methods could, by themselves, monitor both the instantaneous position and motion of check valve internals and valve leakage; however, the combination of acoustic emission monitoring with one of the other methods provides the means to determine vital check valve operational information

27 CFR 70.101 - Bad checks.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 2 2010-04-01 2010-04-01 false Bad checks. 70.101 Section....101 Bad checks. If any check or money order in payment of any amount receivable under Title 26 of the... appropriate TTB officer that such check was tendered in good faith and that such person had reasonable cause...

Structural integrity of rod cluster control assembly of Chashma Nuclear Power Plant -1

International Nuclear Information System (INIS)

Siddiqui, A.; Zafar, F.; Murtaza, G.

2008-01-01

This study has been made in an attempt to verify the structural integrity of Rod Cluster Control Assembly (RCCA) of Chashma Nuclear Power Plant-1(CHASNUPP-1) using ANSYS computer code. The CHASNUPP-1 (PWR type, 300 MWe capacity, unit 1) was built by China at Chashma (District Mianwali), Pakistan. The plant is successfully operating since 2000. The rod cluster control assemblies (RCCA) are used to control fast reactivity changes in PWR type reactors during the normal operation and accident conditions. To fulfill this function the RCCA is stepped upwards or downwards by control rod drive mechanism (CRDM). The stepping action produces a large amount of acceleration. The load produced during stepping is normally considered as limiting one. In this work we have considered the experimental results of a test conducted in China. The test was performed to measure the acceleration produced in upward and downward stepping by CRDM on RCCA, at room temperatures, both in air and static water. The test results showed acceleration (g, m/s 2 ) values, 10.8 - 51.0 and 46.4 - 78.0, in air and static water environments, respectively. Making the analysis on conservative side we selected the highest value of acceleration, 78 g, for our study. To ensure the structural strength, a finite element model of CHASNUPP-1 RCCA has been developed simulating the loading conditions prevailing during reactor operation. This model has been analyzed using the Finite Element Code. The Maximum Stress intensity obtained through this analysis, 186 MPa, is less than the yield stress of RCCA material (∼SS 321), 205 MPa, thus fulfills its structural integrity criteria. (authors)

Check In / Check Out. The Public Space as an Internet of Things

NARCIS (Netherlands)

van t Hof, C.C.G.; van Est, R.; Daemen, F.

2011-01-01

Mobile phones, public transport smart cards, security cameras and GPS systems in our car - we are surrounded by digital devices. They track us, guide us, help us, and control us. The book Check In / Check Out. The Public Space as an Internet of Things shows us how our digital and physical worlds are

Check in / check out : the public space as an internet of things

NARCIS (Netherlands)

Hof, van 't C.; Est, van R.; Daemen, F.

2011-01-01

Mobile phones, public transport smart cards, security cameras and GPS systems in our car - we are surrounded by digital devices. They track us, guide us, help us, and control us. The book Check In / Check Out. The Public Space as an Internet of Things shows us how our digital and physical worlds are

What is a good health check? An interview study of health check providers' views and practices

NARCIS (Netherlands)

Y. Stol (Yrrah); E.C.A. Asscher (Eva); M.H.N. Schermer (Maartje)

2017-01-01

markdownabstract__Background:__ Health checks identify (risk factors for) disease in people without symptoms. They may be offered by the government through population screenings and by other providers to individual users as 'personal health checks'. Health check providers' perspective of 'good'

checkCIF/PLATON (full publication check)

Indian Academy of Sciences (India)

editor handling your paper, to upload your CIF via our web site. PLATON version of 05/02/2014; check.def file version of 05/02/2014. Datablock I - ellipsoid plot http://vm02b.iucr.org/cgi-bin/checkcif_hkl.pl（第 3／4 页）2014-2-12 09:09:12 ...

INTEGRATION OF SHIP HULL ASSEMBLY SEQUENCE PLANNING, SCHEDULING AND BUDGETING

Directory of Open Access Journals (Sweden)

Remigiusz Romuald Iwańkowicz

2015-02-01

Full Text Available The specificity of the yard work requires the particularly careful treatment of the issues of scheduling and budgeting in the production planning processes. The article presents the method of analysis of the assembly sequence taking into account the duration of individual activities and the demand for resources. A method of the critical path and resource budgeting were used. Modelling of the assembly was performed using the acyclic graphs. It has been shown that the assembly sequences can have very different feasible budget regions. The proposed model is applied to the assembly processes of large-scale welded structures, including the hulls of ships. The presented computational examples have a simulation character. They show the usefulness of the model and the possibility to use it in a variety of analyses.

Reexamination of cross-sections for fast neutrons by computational checking of single material integral experiments

International Nuclear Information System (INIS)

Schriewer, J.; Hehn, G.; Mattes, M.

1976-06-01

Transmission experiments for fast neutrons and pure materials offer the possibility to check the accuracy of nuclear data compilations by recalculating the measured discharge spectra. In this paper the calculations were mainly based on two Benchmark experiments with pure iron carried out at the Karlsruhe Nuclear Research Center. One of the experiments employed a 252 Cf fission source and spherically symmetric arrangement; the other was based on transmission of an iron cylinder by 14-MeV neutrons from a D+T source. The checking calculations were based on the data compilation ENDF/B-IV (occasionally also ENDF/B-III) and on the transport codes ANISN (1D) and DOT-2 (2D) with lined up ESTOQ (for calculating the first-collision source). The calculations with the Cf source showed good agreement with the results of measurement, whereas the checking of the arrangement with 14 MeV neutrons yielded a marked underestimation of the neutron flux density in the range of 2 MeV up to 14 MeV. The discussion of the results including the choice of codes was done on the basis of a literature review on the Benchmark experiments for iron with fast neutrons carried out until now. (orig.) [de

Plutonium assemblies in reload 1 of the Dodewaard Reactor

International Nuclear Information System (INIS)

Bairiot, H.; Deramaix, P.; Vandenberg, C.; Leenders, L.; Mostert, P.

1977-01-01

Since 1963, Belgonucleaire has been developing the design of plutonium assemblies of the island type (i.e., plutonium rods inserted in the control zone of the assembly and enriched uranium rods at the periphery) for light water reactors. The application to boiling water reactors (BWRs) led to the introduction, in April 1971, of two prototype plutonium island assemblies in the Dodewaard BWR (The Netherlands): Those assemblies incorporating plutonium in 42 percent of the rods are interchangeable with standard uranium assemblies of the same reload. Their design, which had to meet these criteria, was performed using the routine order in use at Belgonucleaire; experimental checks included a mock-up configuration simulated in the VENUS critical facility at Mol and open-vessel cold critical experiments performed in the Dodewaard core. The pelleted plutonium rods were fabricated and controlled by Belgonucleaire following the manufacturing procedures developed at the production plant. In one of the assemblies, three vibrated plutonium fuel rods with a lower fuel density were introduced in the three most highly rated positions to reduce the power rating. Those plutonium assemblies experienced peak pellet ratings up to 535 W/cm and were discharged in April 1974 after having reached a mean burnup of approximately 21,000 MWd/MT. In-core instrumentation during operation, visual examinations, and reactivity substitution experiments during reactor shutdown did not indicate any special feature for those assemblies compared to the standard uranium assemblies, thereby demonstrating their interchangeability

[Design and implementation of data checking system for Chinese materia medica resources survey].

Science.gov (United States)

Wang, Hui; Zhang, Xiao-Bo; Ge, Xiao-Guang; Jin, Yan; Jing, Zhi-Xian; Qi, Yuan-Hua; Wang, Ling; Zhao, Yu-Ping; Wang, Wei; Guo, Lan-Ping; Huang, Lu-Qi

2017-11-01

The Chinese material medica resources (CMMR) national survey information management system has collected a large amount of data. To help dealing with data recheck, reduce the work of inside, improve the recheck of survey data from provincial and county level, National Resource Center for Chinese Materia Medical has designed a data checking system for Chinese material medica resources survey based on J2EE technology, Java language, Oracle data base in accordance with the SOA framework. It includes single data check, check score, content manage, check the survey data census data with manual checking and automatic checking about census implementation plan, key research information, general survey information, cultivation of medicinal materials information, germplasm resources information the medicine information, market research information, traditional knowledge information, specimen information of this 9 aspects 20 class 175 indicators in two aspects of the quantity and quality. The established system assists in the completion of the data consistency and accuracy, pushes the county survey team timely to complete the data entry arrangement work, so as to improve the integrity, consistency and accuracy of the survey data, and ensure effective and available data, which lay a foundation for providing accurate data support for national survey of the Chinese material medica resources (CMMR) results summary, and displaying results and sharing. Copyright© by the Chinese Pharmaceutical Association.

Diagnostic framework and health check tool for engineering and technology projects

Directory of Open Access Journals (Sweden)

Simon P Philbin

2014-10-01

Full Text Available Purpose: Development of a practitioner oriented diagnostic framework and health check tool to support the robust assessment of engineering and technology projects.Design/methodology/approach: The research is based on a literature review that draws together insights on project assessment and critical success factors to establish an integrated systems view of projects. This is extended to allow a comprehensive diagnostic framework to be developed along with a high-level health check tool that can be readily deployed on projects. The utility of the diagnostic framework and health check tool are explored through three illustrative case studies, with two from Canada and one from the United Kingdom. Findings andOriginality/value: The performance of engineering and technology projects can be viewed through a systems perspective and being a function of six sub-systems that are: process, technology, resources, impact, knowledge and culture. The diagnostic framework that is developed through this research integrates these sub-systems to provide a comprehensive assessment methodology for projects, which is linked to existing best practice for project reviews, performance management and maturity models. The case studies provide managerial insights that are related to the diagnostic framework but crucially also position the approach in the context of industrial applications for construction engineering and technology management.Research limitations/implications: The case study approach includes two case studies from the construction and facilities development sector with the third case study from the research and technology sector. Further work is required to investigate the use of the diagnostic framework and health check tool in other sectors.Practical implications: The health check tool will be of practical benefit to new projects managers that require access to a robust and convenient project review methodology for assessing the status and health of a

Photonic hybrid assembly through flexible waveguides

NARCIS (Netherlands)

Wörhoff, Kerstin; Prak, Albert; postma, F; Leinse, A; Wu, K.; Peters, T.J.; Tichem, M.; Amaning-Appiah, B.; Renukappa, V.; Vollrath, G.; Balcells-Ventura, J.; Uhlig, P.; Seyfried, M.; Rose, D.; Santos, Raquel; Leijtens, XJM; Flintham, B.; Wale, M.; Robbins, D.; Vivien, Laurent; Pavesi, Lorenzo; Pelli, Stefano

2016-01-01

Fully automated, high precision, cost-effective assembly technology for photonic packages remains one of the main challenges in photonic component manufacturing. Next to the cost aspect the most demanding assembly task for multiport photonic integrated circuits (PICs) is the high-precision (±0.1

Integrated safeguards and security for a highly automated process

International Nuclear Information System (INIS)

Zack, N.R.; Hunteman, W.J.; Jaeger, C.D.

1993-01-01

Before the cancellation of the New Production Reactor Programs for the production of tritium, the reactors and associated processing were being designed to contain some of the most highly automated and remote systems conceived for a Department of Energy facility. Integrating safety, security, materials control and accountability (MC and A), and process systems at the proposed facilities would enhance the overall information and protection-in-depth available. Remote, automated fuel handling and assembly/disassembly techniques would deny access to the nuclear materials while upholding ALARA principles but would also require the full integration of all data/information systems. Such systems would greatly enhance MC and A as well as facilitate materials tracking. Physical protection systems would be connected with materials control features to cross check activities and help detect and resolve anomalies. This paper will discuss the results of a study of the safeguards and security benefits achieved from a highly automated and integrated remote nuclear facility and the impacts that such systems have on safeguards and computer and information security

Integrating complex functions: coordination of nuclear pore complex assembly and membrane expansion of the nuclear envelope requires a family of integral membrane proteins.

Science.gov (United States)

Schneiter, Roger; Cole, Charles N

2010-01-01

The nuclear envelope harbors numerous large proteinaceous channels, the nuclear pore complexes (NPCs), through which macromolecular exchange between the cytosol and the nucleoplasm occurs. This double-membrane nuclear envelope is continuous with the endoplasmic reticulum and thus functionally connected to such diverse processes as vesicular transport, protein maturation and lipid synthesis. Recent results obtained from studies in Saccharomyces cerevisiae indicate that assembly of the nuclear pore complex is functionally dependent upon maintenance of lipid homeostasis of the ER membrane. Previous work from one of our laboratories has revealed that an integral membrane protein Apq12 is important for the assembly of functional nuclear pores. Cells lacking APQ12 are viable but cannot grow at low temperatures, have aberrant NPCs and a defect in mRNA export. Remarkably, these defects in NPC assembly can be overcome by supplementing cells with a membrane fluidizing agent, benzyl alcohol, suggesting that Apq12 impacts the flexibility of the nuclear membrane, possibly by adjusting its lipid composition when cells are shifted to a reduced temperature. Our new study now expands these findings and reveals that an essential membrane protein, Brr6, shares at least partially overlapping functions with Apq12 and is also required for assembly of functional NPCs. A third nuclear envelope membrane protein, Brl1, is related to Brr6, and is also required for NPC assembly. Because maintenance of membrane homeostasis is essential for cellular survival, the fact that these three proteins are conserved in fungi that undergo closed mitoses, but are not found in metazoans or plants, may indicate that their functions are performed by proteins unrelated at the primary sequence level to Brr6, Brl1 and Apq12 in cells that disassemble their nuclear envelopes during mitosis.

A Theoretical and Experimental Study of DNA Self-assembly

Science.gov (United States)

Chandran, Harish

providing detailed designs for local molecular computations that involve spatially contiguous molecules arranged on addressable substrates via enzyme-free DNA hybridization reaction cascades. We use the Visual DSD simulation software in conjunction with localized reaction rates obtained from biophysical modeling to create chemical reaction networks of localized hybridization circuits that are then model checked using the PRISM model checking software. We develop a DNA detection system employing the triggered self-assembly of a novel DNA dendritic nanostructure. Detection begins when a specific, single-stranded target DNA strand triggers a hybridization chain reaction between two distinct DNA hairpins. Each hairpin opens and hybridizes up to two copies of the other, and hence each layer of the growing dendritic nanostructure can in principle accommodate an exponentially increasing number of cognate molecules, generating a nanostructure with high molecular weight. We build linear activatable assemblies employing a novel protection/deprotection strategy to strictly enforce the direction of tiling assembly growth to ensure the robustness of the assembly process. Our system consists of two tiles that can form a linear co-polymer. These tiles, which are initially protected such that they do not react with each other, can be activated to form linear co-polymers via the use of a strand displacing enzyme.

Photonic hybrid assembly through flexible waveguides

NARCIS (Netherlands)

Wörhoff, K.; Prak, A.; Postma, F.; Leinse, A.; Wu, K.; Peters, T. J.; Tichem, M.; Amaning-Appiah, B.; Renukappa, V.; Vollrath, G.; Balcells-Ventura, J.; Uhlig, P.; Seyfried, M.; Rose, D.; Santos, R.; Leijtens, X.J.M.; Flintham, B.; Wale, M.; Robbins, D.

2016-01-01

Fully automated, high precision, cost-effective assembly technology for photonic packages remains one of the main challenges in photonic component manufacturing. Next to the cost aspect the most demanding assembly task for multiport photonic integrated circuits (PICs) is the high-precision (±0.1 μm)

Model Checking Markov Chains: Techniques and Tools

NARCIS (Netherlands)

Zapreev, I.S.

2008-01-01

This dissertation deals with four important aspects of model checking Markov chains: the development of efficient model-checking tools, the improvement of model-checking algorithms, the efficiency of the state-space reduction techniques, and the development of simulation-based model-checking

Handling apparatus for a nuclear reactor fuel assembly

International Nuclear Information System (INIS)

Shallenberger, J.M.; Hornak, L.P.; Desmarchais, W.E.

1978-01-01

An apparatus is disclosed for handling radioactive fuel assembly during transfer operations. The radioactive fuel assembly is drawn up into a shielding sleeve which substantially reduces the level of radioactivity immediately surrounding the sleeve thereby permitting direct access by operating personnel. The lifting assembly which draws the fuel assembly up within the shielding sleeve is mounted to and forms an integral part of the handling apparatus. The shielding sleeve accompanies the fuel assembly during all of the transfer operations

Model Checking Structured Infinite Markov Chains

NARCIS (Netherlands)

Remke, Anne Katharina Ingrid

2008-01-01

In the past probabilistic model checking hast mostly been restricted to finite state models. This thesis explores the possibilities of model checking with continuous stochastic logic (CSL) on infinite-state Markov chains. We present an in-depth treatment of model checking algorithms for two special

Model checking software for phylogenetic trees using distribution and database methods

Directory of Open Access Journals (Sweden)

Requeno José Ignacio

2013-12-01

Full Text Available Model checking, a generic and formal paradigm stemming from computer science based on temporal logics, has been proposed for the study of biological properties that emerge from the labeling of the states defined over the phylogenetic tree. This strategy allows us to use generic software tools already present in the industry. However, the performance of traditional model checking is penalized when scaling the system for large phylogenies. To this end, two strategies are presented here. The first one consists of partitioning the phylogenetic tree into a set of subgraphs each one representing a subproblem to be verified so as to speed up the computation time and distribute the memory consumption. The second strategy is based on uncoupling the information associated to each state of the phylogenetic tree (mainly, the DNA sequence and exporting it to an external tool for the management of large information systems. The integration of all these approaches outperforms the results of monolithic model checking and helps us to execute the verification of properties in a real phylogenetic tree.

SCT Barrel Assembly Complete

CERN Multimedia

L. Batchelor

As reported in the April 2005 issue of the ATLAS eNews, the first of the four Semiconductor Tracker (SCT) barrels, complete with modules and services, arrived safely at CERN in January of 2005. In the months since January, the other three completed barrels arrived as well, and integration of the four barrels into the entire barrel assembly commenced at CERN, in the SR1 building on the ATLAS experimental site, in July. Assembly was completed on schedule in September, with the addition of the innermost layer to the 4-barrel assembly. Work is now underway to seal the barrel thermal enclosure. This is necessary in order to enclose the silicon tracker in a nitrogen atmosphere and provide it with faraday-cage protection, and is a delicate and complicated task: 352 silicon module powertapes, 352 readout-fibre bundles, and over 400 Detector Control System sensors must be carefully sealed into the thermal enclosure bulkhead. The team is currently verifying the integrity of the low mass cooling system, which must be d...

Electron transfer dynamics across self-assembled N-(2-mercaptoethyl) octadecanamide/mycolic acid layers: impedimetric insights into the structural integrity and interaction with anti-mycolic acid antibodies

CSIR Research Space (South Africa)

Ozoemena, KI

2010-01-01

Full Text Available The integrity and properties of mycolic acid (MA) antigens integrated into a self-assembled monolayer (SAM) of N-(2-mercaptoethyl)octadecanamide, (MEODA), on a gold electrode have been interrogated using cyclic voltammetry (CV) and electrochemical...

Fuel assembly reconstitution

International Nuclear Information System (INIS)

Morgado, Mario M.; Oliveira, Monica G.N.; Ferreira Junior, Decio B.M.; Santos, Barbara O. dos; Santos, Jorge E. dos

2009-01-01

Fuel failures have been happened in Nuclear Power Plants worldwide, without lost of integrity and safety, mainly for the public, environment and power plants workers. The most common causes of these events are corrosion (CRUD), fretting and pellet cladding interaction. These failures are identified by increasing the activity of fission products, verified by chemical analyses of reactor coolant. Through these analyses, during the fourth operation cycle of Angra 2 Nuclear Power Plant, was possible to observe fuel failure indication. This indication was confirmed in the end of the cycle during the unloading of reactor core through leakage tests of fuel assembly, using the equipment called 'In Mast Sipping' and 'Box Sipping'. After confirmed, the fuel assembly reconstitution was scheduled, and happened in April, 2007, where was identified the cause and the fuel rod failure, which was substitute by dummy rods (zircaloy). The cause was fretting by 'debris'. The actions to avoid and prevent fuel assemblies failures are important. The goals of this work are to describe the methodology of fuel assembly reconstitution using the FARE (Fuel Assembly Reconstitution Equipment) system, to describe the results of this task in economic and security factors of the company and show how the fuel assembly failures are identified during operation and during the outage. (author)

The Assembly and Test of Pressure Vessel for Irradiation

International Nuclear Information System (INIS)

Park, Kook Nam; Lee, Jong Min; Youn, Young Jung; June, Hyung Kil; Ahn, Sung Ho; Lee, Kee Hong; Kim, Young Ki; Kennedy, Timothy C.

2009-01-01

The Fuel Test Loop(FTL) which is capable of an irradiation testing under a similar operating condition to those of PWR(Pressurized Water Reactor) and CANDU(CANadian Deuterium Uranium reactor) nuclear power plants has been developed and installed in HANARO, KAERI(Korea Atomic Energy Research Institute). It consists of In-Pile Section(IPS) and Out-of Pile System(OPS). The IPS, which is located inside the pool is divided into 3-parts: the in-pool pipes, the IVA(IPS Vessel Assembly) and the support structures. The test fuel is loaded inside a double wall, inner pressure vessel and outer pressure vessel, to keep the functionality of the reactor coolant pressure boundary. The IVA is manufactured by local company and the functional test and verification were done through pressure drop, vibration, hydraulic and leakage tests. The brazing technique for the instrument lines has been checked for its functionality and performance. An IVA has been manufactured by local technique and have finally tested under high temperature and high pressure. The IVA and piping did not experience leakage, as we have checked the piping, flanges, assembly parts. We have obtained good data during the three cycle test which includes a pressure test, pressure and temperature cycling, and constant temperature

The Assembly and Test of Pressure Vessel for Irradiation

Energy Technology Data Exchange (ETDEWEB)

Park, Kook Nam; Lee, Jong Min; Youn, Young Jung; June, Hyung Kil; Ahn, Sung Ho; Lee, Kee Hong; Kim, Young Ki [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Kennedy, Timothy C. [Oregon State University, Corvallis (United States)

2009-02-15

The Fuel Test Loop(FTL) which is capable of an irradiation testing under a similar operating condition to those of PWR(Pressurized Water Reactor) and CANDU(CANadian Deuterium Uranium reactor) nuclear power plants has been developed and installed in HANARO, KAERI(Korea Atomic Energy Research Institute). It consists of In-Pile Section(IPS) and Out-of Pile System(OPS). The IPS, which is located inside the pool is divided into 3-parts: the in-pool pipes, the IVA(IPS Vessel Assembly) and the support structures. The test fuel is loaded inside a double wall, inner pressure vessel and outer pressure vessel, to keep the functionality of the reactor coolant pressure boundary. The IVA is manufactured by local company and the functional test and verification were done through pressure drop, vibration, hydraulic and leakage tests. The brazing technique for the instrument lines has been checked for its functionality and performance. An IVA has been manufactured by local technique and have finally tested under high temperature and high pressure. The IVA and piping did not experience leakage, as we have checked the piping, flanges, assembly parts. We have obtained good data during the three cycle test which includes a pressure test, pressure and temperature cycling, and constant temperature.

Software tool for physics chart checks.

Science.gov (United States)

Li, H Harold; Wu, Yu; Yang, Deshan; Mutic, Sasa

2014-01-01

Physics chart check has long been a central quality assurance (QC) measure in radiation oncology. The purpose of this work is to describe a software tool that aims to accomplish simplification, standardization, automation, and forced functions in the process. Nationally recognized guidelines, including American College of Radiology and American Society for Radiation Oncology guidelines and technical standards, and the American Association of Physicists in Medicine Task Group reports were identified, studied, and summarized. Meanwhile, the reported events related to physics chart check service were analyzed using an event reporting and learning system. A number of shortfalls in the chart check process were identified. To address these problems, a software tool was designed and developed under Microsoft. Net in C# to hardwire as many components as possible at each stage of the process. The software consists of the following 4 independent modules: (1) chart check management; (2) pretreatment and during treatment chart check assistant; (3) posttreatment chart check assistant; and (4) quarterly peer-review management. The users were a large group of physicists in the author's radiation oncology clinic. During over 1 year of use the tool has proven very helpful in chart checking management, communication, documentation, and maintaining consistency. The software tool presented in this work aims to assist physicists at each stage of the physics chart check process. The software tool is potentially useful for any radiation oncology clinics that are either in the process of pursuing or maintaining the American College of Radiology accreditation.

25 CFR 115.704 - May we accept for deposit into a trust account retirement checks/payments or pension fund checks...

Science.gov (United States)

2010-04-01

... checks/payments or pension fund checks/payments even though those funds are not specified in § 115.702... May we accept for deposit into a trust account retirement checks/payments or pension fund checks.../payments or pension fund checks/payments or any funds from sources that are not identified in the table in...

Model checking as an aid to procedure design

International Nuclear Information System (INIS)

Zhang, Wenhu

2001-01-01

The OECD Halden Reactor Project has been actively working on computer assisted operating procedures for many years. The objective of the research has been to provide computerised assistance for procedure design, verification and validation, implementation and maintenance. For the verification purpose, the application of formal methods has been considered in several reports. The recent formal verification activity conducted at the Halden Project is based on using model checking to the verification of procedures. This report presents verification approaches based on different model checking techniques and tools for the formalization and verification of operating procedures. Possible problems and relative merits of the different approaches are discussed. A case study of one of the approaches is presented to show the practical application of formal verification. Application of formal verification in the traditional procedure design process can reduce the human resources involved in reviews and simulations, and hence reduce the cost of verification and validation. A discussion of the integration of the formal verification with the traditional procedure design process is given at the end of this report. (Author)

Development of unfolding method to obtain pin-wise source strength distribution from PWR spent fuel assembly measurement

International Nuclear Information System (INIS)

Sitompul, Yos Panagaman; Shin, Hee-Sung; Park, Se-Hwan; Oh, Jong Myeong; Seo, Hee; Kim, Ho Dong

2013-01-01

An unfolding method has been developed to obtain a pin-wise source strength distribution of a 14 × 14 pressurized water reactor (PWR) spent fuel assembly. Sixteen measured gamma dose rates at 16 control rod guide tubes of an assembly are unfolded to 179 pin-wise source strengths of the assembly. The method calculates and optimizes five coefficients of the quadratic fitting function for X-Y source strength distribution, iteratively. The pin-wise source strengths are obtained at the sixth iteration, with a maximum difference between two sequential iterations of about 0.2%. The relative distribution of pin-wise source strength from the unfolding is checked using a comparison with the design code (Westinghouse APA code). The result shows that the relative distribution from the unfolding and design code is consistent within a 5% difference. The absolute value of the pin-wise source strength is also checked by reproducing the dose rates at the measurement points. The result shows that the pin-wise source strengths from the unfolding reproduce the dose rates within a 2% difference. (author)

[Pre-verbality in focusing and the need for self check. An attempt at "focusing check"].

Science.gov (United States)

Masui, T; Ikemi, A; Murayama, S

1983-06-01

Though the Focusing process is not entirely non-verbal, in Focusing, careful attention is paid by the Focuser and the Listener to the pre-verbal experiential process. In other words, Focusing involves attending to the felt sense that is not easily expressed in words immediately. Hence, during the process of learning to Focus, the Focusing teacher attempts to communicate the experiences of Focusing to the student which are not easily done by words. Due to such difficulties, the Focusing student may (and quite frequently does) mistake the experiential process in Focusing with other processes. Often, the felt sense can be confused with other phenomena such as "autogenic discharge". Also the Focuser may not stay with the felt sense and drift into "free association" or frequently, certain processes in "meditation" can be confused with Focusing. Therefore, there is a need for a "check" by which the Focusing student can confirm the Focusing experience for himself. For the Focusing student, such a "check" serves not only to confirm the Focusing process, but also an aid to learning Focusing. We will report here a "Focusing Check" which we developed by translating Eugene Gendlin's "Focusing Check" and making several modifications in it so that it will be more understandable to the Japanese. Along with the "Focusing Check" we developed, the authors discuss the need for such a check.

[Infection prevention check-in and infection prevention check-out to prevent nosocomial infections].

Science.gov (United States)

Kramer, A; Schilling, M; Heidecke, C D

2010-02-01

A precondition for the success of the prevention of SSI is the complete realisation of the proven anti-infective measures in form of the multi-barrier strategy or the so-called bundles. In daily practice it is important to follow the fixed instructions, i. e., to ensure a high compliance. In much the same way as an airline pilot or co-pilot must examine whether all instruments are functioning before each take-off, a comparable procedure should be developed as a pre-operative control for the observance of all -defined measures by the responsible surgeon and for the post-operative supervision by the patient. For the control of the observance of the defined pre-operative prevention measures, a check list with 12 items was developed, named the "infection prevention check-in". The check list is authorised by the responsible surgeon be-fore each operation. For the surveillance of the general hygiene in the post-operative period the "infection prevention check-out" with 14 items was developed. Thereby the patient is able to evaluate the staff's compliance with the hygienic measures at the time of dismissal. With the introduction of the check-lists a simple means is given to involve both the team of the surgeons and the ward staff, together with the patient, into the infection prophylaxis even more effectively. In order to assess the success of those measures, the influence on the rate of SSI is to be determined prospectively. Georg Thieme Verlag Stuttgart, New York.

QuickChecking static analysis properties

DEFF Research Database (Denmark)

Midtgaard, Jan; Møller, Anders

2017-01-01

A static analysis can check programs for potential errors. A natural question that arises is therefore: who checks the checker? Researchers have given this question varying attention, ranging from basic testing techniques, informal monotonicity arguments, thorough pen-and-paper soundness proofs....... Moreover, we offer a number of generic, type-safe combinators to check transfer functions and operators on lattices, to help ensure that these are, eg, monotone, strict, or invariant. We substantiate our claims by quickchecking a type analysis for the Lua programming language....

Neural nets for the plausibility check of measured values in the integrated measurement and information system for the surveillance of environmental radioactivity (IMIS)

International Nuclear Information System (INIS)

Haase, G.

2003-01-01

Neural nets to the plausibility check of measured values in the ''integrated measurement and information system for the surveillance of environmental radioactivity, IMIS'' is a research project supported by the Federal Minister for the Environment, Nature Conservation and Nuclear Safety. A goal of this project was the automatic recognition of implausible measured values in the data base ORACLE, which measured values from surveillance of environmental radioactivity of most diverse environmental media contained. The conversion of this project [ 1 ] was realized by institut of logic, complexity and deduction systems of the university Karlsruhe under the direction of Professor Dr. Menzel, Dr. Martin Riedmueller and Martin Lauer. (orig.)

Storage method for spent fuel assembly

International Nuclear Information System (INIS)

Tajiri, Hiroshi.

1992-01-01

In the present invention, spent fuel assemblies are arranged at a dense pitch in a storage rack by suppressing the reactivity of the assemblies, to increase storage capacity for the spent fuel assemblies. That is, neutron absorbers are filled in the cladding tube of an absorbing rod, and the diameter thereof is substantially equal with that of a fuel rod. A great amount of the absorbing rods are arranged at the outer circumference of the fuel assembly. Then, they are fixed integrally to the fuel assembly and stored in a storage rack. In this case, the storage rack may be constituted only with angle materials which are inexpensive and installed simply. With such a constitution, in the fuel assembly having absorbing rods wound therearound, neutrons are absorbed by absorbing rods and the reactivity is lowered. Accordingly, the assembly arrangement pitch in the storage rack can be made dense. As a result, the storage capacity for the assemblies is increased. (I.S.)

Rocket Assembly and Checkout Facility

Data.gov (United States)

Federal Laboratory Consortium — FUNCTION: Integrates, tests, and calibrates scientific instruments flown on sounding rocket payloads. The scientific instruments are assembled on an optical bench;...

Classification of assembly techniques for micro products

DEFF Research Database (Denmark)

Hansen, Hans Nørgaard; Tosello, Guido; Gegeckaite, Asta

2005-01-01

of components and level of integration are made. This paper describes a systematic characterization of micro assembly methods. This methodology offers the opportunity of a cross comparison among different techniques to gain a choosing principle of the favourable micro assembly technology in a specific case...

49 CFR 570.10 - Wheel assemblies.

Science.gov (United States)

2010-10-01

... bead through one full wheel revolution and note runout in excess of one-eighth of an inch. (c) Mounting... 49 Transportation 6 2010-10-01 2010-10-01 false Wheel assemblies. 570.10 Section 570.10... Pounds or Less § 570.10 Wheel assemblies. (a) Wheel integrity. A tire rim, wheel disc, or spider shall...

Comparison of de novo assembly statistics of Cucumis sativus L.

Science.gov (United States)

Wojcieszek, Michał; Kuśmirek, Wiktor; Pawełkowicz, Magdalena; PlÄ der, Wojciech; Nowak, Robert M.

2017-08-01

Genome sequencing is the core of genomic research. With the development of NGS and lowering the cost of procedure there is another tight gap - genome assembly. Developing the proper tool for this task is essential as quality of genome has important impact on further research. Here we present comparison of several de Bruijn assemblers tested on C. sativus genomic reads. The assessment shows that newly developed software - dnaasm provides better results in terms of quantity and quality. The number of generated sequences is lower by 5 - 33% with even two fold higher N50. Quality check showed reliable results were generated by dnaasm. This provides us with very strong base for future genomic analysis.

Modernization of internal target assembly for AIC-144 cyclotron - proposal

International Nuclear Information System (INIS)

Petelenz, B.; Szalkowski, M.

2007-01-01

The report describes a prototype of the remotely controlled internal target assembly, designed and built in the Institute of Nuclear Physics. After a series of technical tests, the machine was used in 2006 to produce 73 As from proton bombarded germanium targets. Before this, distribution of the proton beam on the target was checked by autoradiography of irradiated copper foils exposed on large area thermoluminescence detectors. Since the experiments exhibited some severe drawbacks of the machine, the report gives hints how to get rid of them, which is the answer to the question asked by the Deputy Director of the Institute on the topic. The construction parts of the assembly are listed in the Chapter 10. (author)

Self-checking in a logic protection system using a redundant computer structure

International Nuclear Information System (INIS)

Darier, P.; Lallement, D.

1978-01-01

The logic protection system described has a parallel and redundant computer structure. Each assembly consists of an analog and digital acquisition module, a processing unit and a simple and reliable logical decision device adapted to the redundancy of the system (two-out-of-three or two-out-of-four). Each processing unit monitors all the detection units, processes the values received and works out the corresponding decisions. The decisions are collated in the final stage in a majority decision element which sets the protective action in motion. At all levels the quality of data transmission and validity of processing are tested in order that the best strategy may be applied in the event of damage to the system. Several self-checking techniques were used: they include a set of electronic test modules connected to the processing unit, on-line system testing and control software and time control devices which provide a final verification of the overall operation of the system. Self-checking and test operations are performed regularly throughout surveillance cycles. Problems of fault detection and of protection against the effects of faults are examined from the aspect of hardware and software. (author)

25 CFR 11.421 - Bad checks.

Science.gov (United States)

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Bad checks. 11.421 Section 11.421 Indians BUREAU OF... Criminal Offenses § 11.421 Bad checks. (a) A person who issues or passes a check or similar sight order for..., and the issuer failed to make good within 10 days after receiving notice of that refusal. ...

Assembly & Metrology of First Wall Components of SST-1

Science.gov (United States)

Parekh, Tejas; Santra, Prosenjit; Biswas, Prabal; Patel, Hiteshkumar; Paravastu, Yuvakiran; Jaiswal, Snehal; Chauhan, Pradeep; Babu, Gattu Ramesh; A, Arun Prakash; Bhavsar, Dhaval; Raval, Dilip C.; Khan, Ziauddin; Pradhan, Subrata

2017-04-01

First Wall Components (FWC) of SST-1 tokamak, which are in the immediate vicinity of plasma comprises of limiters, divertors, baffles, passive stabilizers are designed to operate long duration (1000 s) discharges of elongated plasma. All FWC consists of a copper alloy heat sink modules with SS cooling tubes brazed onto it, graphite tiles acting as armour material facing the plasma, and are mounted to the vacuum vessels with suitable Inconel support structures at ring & port locations. The FWC are very recently assembled and commissioned successfully inside the vacuum vessel of SST-1 undergoing a meticulous planning of assembly sequence, quality checks at every stage of the assembly process. This paper will present the metrology aspects & procedure of each FWC, both outside the vacuum vessel, and inside the vessel, assembly tolerances, tools, equipment and jig/fixtures, used at each stage of assembly, starting from location of support bases on vessel rings, fixing of copper modules on support structures, around 3800 graphite tile mounting on 136 copper modules with proper tightening torques, till final toroidal and poloidal geometry of the in-vessel components are obtained within acceptable limits, also ensuring electrical continuity of passive stabilizers to form a closed saddle loop, electrical isolation of passive stabilizers from vacuum vessel.

QuickChecking Static Analysis Properties

DEFF Research Database (Denmark)

Midtgaard, Jan; Møller, Anders

2015-01-01

A static analysis can check programs for potential errors. A natural question that arises is therefore: who checks the checker? Researchers have given this question varying attention, ranging from basic testing techniques, informal monotonicity arguments, thorough pen-and-paper soundness proofs...... of a lattice. Moreover, we offer a number of generic, type-safe combinators to check transfer functions and operators on lattices, to help ensure that these are, e.g., monotone, strict, or invariant. We substantiate our claims by quickchecking a type analysis for the Lua programming language...

Effects of low heterogeneity in fast critical assemblies

International Nuclear Information System (INIS)

Belov, S.P.; Dulin, V.A.; Zhukov, A.V.; Kuzin, E.N.; Mozhaev, V.K.; Sitnikov, V.I.; Tsibulya, A.M.; Shapar', A.V.; Zayfert, E.; Kuntsman, B.; Khayntsel'man, B.

1989-01-01

The problem of the low heterogeneity of fast critical assemblies, which are used to simulate fast reactors that are under design, has begun to assume increasing importance as the errors in nuclear data and group constants decrease and the capabilities of design codes improve. The design of the fuel channels of the fast critical assemblies of a BFS differs from that of the fuel subassemblies of a power reactor. The principal difference is that critical assemblies have a more heterogeneous structure than a reactor core does. As a result, the effects of this heterogeneity turn out to be appreciable for a number of functionals. Of particular interest was the measurement of the main neutronic characteristics of a fast reactor in its actual design and in the mockup produced by using BFS facilities. The authors measured and calculated the most important functionals (the ratios of the average cross sections of the main absorbing and fissioning elements, etc.) for both a homogeneous medium (fuel assemblies) and a heterogeneous medium (slugs, tubes) of practically identical composition. The objective of this work was to compare the discrepancy between experiment and calculations for the central functionals in the homogeneous and heterogeneous cases after corrections. This is a check of the accuracy of the simulation of homogeneous cores in fast power reactors by using the tools of the BFS fast critical assembly

Diagnostic information in compliance checking

NARCIS (Netherlands)

Ramezani Taghiabadi, E.; Fahland, D.; Aalst, van der W.M.P.

2012-01-01

Compliance checking is gaining importance as today's organizations need to show that operational processes are executed in a controlled manner while satisfying predefined (legal) requirements. Deviations may be costly and expose the organization to severe risks. Compliance checking is of growing

Non intrusive check valve diagnostics at Bruce A

International Nuclear Information System (INIS)

Marsch, S.P.

1997-01-01

Bruce A purchased non intrusive check valve diagnostic equipment in 1995 to ensure operability and availability of critical check valves in the Station. Diagnostics can be used to locate and monitor check valve degradation modes. Bruce A initiated a pilot program targeting check valves with flow through them and ones that completed open or close cycles. Approaches to determine how to confirm operability of passive check valves using non intrusive techniques were explored. A sample population of seventy-three check valves was selected to run the pilot program on prior to complete implementation. The pilot program produced some significant results and some inconclusive results. The program revealed a major finding that check valve performance modeling is required to ensure continuous operability of check valves. (author)

Non intrusive check valve diagnostics at Bruce A

Energy Technology Data Exchange (ETDEWEB)

Marsch, S.P. [Ontario Hydro, Bruce Nuclear Generating Station A, Tiverton, ON (Canada)

1997-07-01

Bruce A purchased non intrusive check valve diagnostic equipment in 1995 to ensure operability and availability of critical check valves in the Station. Diagnostics can be used to locate and monitor check valve degradation modes. Bruce A initiated a pilot program targeting check valves with flow through them and ones that completed open or close cycles. Approaches to determine how to confirm operability of passive check valves using non intrusive techniques were explored. A sample population of seventy-three check valves was selected to run the pilot program on prior to complete implementation. The pilot program produced some significant results and some inconclusive results. The program revealed a major finding that check valve performance modeling is required to ensure continuous operability of check valves. (author)

49 CFR 571.209 - Standard No. 209; Seat belt assemblies.

Science.gov (United States)

2010-10-01

... seat belt assembly to fit the user, including such hardware that may be integral with a buckle... the proper use of the assembly, stressing particularly the importance of wearing the assembly snugly... of Standard No. 208. (a)(1) A manual seat belt assembly, which is subject to the requirements of S5.1...

Implementing Check in/Check out for Students with Intellectual Disability in Self-Contained Classrooms

Science.gov (United States)

Boden, Lauren J.; Ennis, Robin P.; Jolivette, Kristine

2012-01-01

Check in/check out (CICO) is a secondary-tier intervention implemented within the framework of schoolwide positive behavior interventions and supports (SWPBIS) that uses school-based contingencies to encourage positive behavior. CICO is a five-step cycle which uses daily progress report cards (DPR) to monitor progress toward schoolwide or…

Direct measurement of Cu surface self-diffusion on a checked surface

International Nuclear Information System (INIS)

Cousty, Jacques; Peix, Roger; Perraillon, Bernard.

1976-01-01

A radiotracer technique ( 64 Cu) was developed to measure surface diffusion on copper surfaces of total impurity concentration not exceeding some 10 -3 monolayers. The apparatus used consists of a slow electron diffraction device, an Auger analysis spectrometer (CMA), an ion gun and an evaporation device assembled in an ultra-vacuum chamber holding a residual pressure below 10 -10 Torr. A sample handler enables the surface studied to be positioned in front of each of these instruments. During the diffusion treatment the chemical composition of the surface is checked intermittently, and afterwards the spread of the deposit is measured outside the ultravacuum chamber. Slices several microns thick are removed and dissolved separately in dishes containing HNO 3 . The activity is then measured with a flow counter [fr

Biochemia Medica has started using the CrossCheck plagiarism detection software powered by iThenticate

Science.gov (United States)

Šupak-Smolčić, Vesna; Šimundić, Ana-Maria

2013-01-01

In February 2013, Biochemia Medica has joined CrossRef, which enabled us to implement CrossCheck plagiarism detection service. Therefore, all manuscript submitted to Biochemia Medica are now first assigned to Research integrity editor (RIE), before sending the manuscript for peer-review. RIE submits the text to CrossCheck analysis and is responsible for reviewing the results of the text similarity analysis. Based on the CrossCheck analysis results, RIE subsequently provides a recommendation to the Editor-in-chief (EIC) on whether the manuscript should be forwarded to peer-review, corrected for suspected parts prior to peer-review or immediately rejected. Final decision on the manuscript is, however, with the EIC. We hope that our new policy and manuscript processing algorithm will help us to further increase the overall quality of our Journal. PMID:23894858

Nuclear imaging of the fuel assembly in ignition experiments

Energy Technology Data Exchange (ETDEWEB)

Grim, G. P.; Guler, N.; Merrill, F. E.; Morgan, G. L.; Danly, C. R.; Volegov, P. L.; Wilde, C. H.; Wilson, D. C.; Clark, D. S.; Hinkel, D. E.; Jones, O. S.; Raman, K. S.; Izumi, N.; Fittinghoff, D. N.; Drury, O. B.; Alger, E. T.; Arnold, P. A.; Ashabranner, R. C.; Atherton, L. J.; Barrios, M. A.; Batha, S.; Bell, P. M.; Benedetti, L. R.; Berger, R. L.; Bernstein, L. A.; Berzins, L. V.; Betti, R.; Bhandarkar, S. D.; Bionta, R. M.; Bleuel, D. L.; Boehly, T. R.; Bond, E. J.; Bowers, M. W.; Bradley, D. K.; Brunton, G. K.; Buckles, R. A.; Burkhart, S. C.; Burr, R. F.; Caggiano, J. A.; Callahan, D. A.; Casey, D. T.; Castro, C.; Celliers, P. M.; Cerjan, C. J.; Chandler, G. A.; Choate, C.; Cohen, S. J.; Collins, G. W.; Cooper, G. W.; Cox, J. R.; Cradick, J. R.; Datte, P. S.; Dewald, E. L.; Di Nicola, P.; Di Nicola, J. M.; Divol, L.; Dixit, S. N.; Dylla-Spears, R.; Dzenitis, E. G.; Eckart, M. J.; Eder, D. C.; Edgell, D. H.; Edwards, M. J.; Eggert, J. H.; Ehrlich, R. B.; Erbert, G. V.; Fair, J.; Farley, D. R.; Felker, B.; Fortner, R. J.; Frenje, J. A.; Frieders, G.; Friedrich, S.; Gatu-Johnson, M.; Gibson, C. R.; Giraldez, E.; Glebov, V. Y.; Glenn, S. M.; Glenzer, S. H.; Gururangan, G.; Haan, S. W.; Hahn, K. D.; Hammel, B. A.; Hamza, A. V.; Hartouni, E. P.; Hatarik, R.; Hatchett, S. P.; Haynam, C.; Hermann, M. R.; Herrmann, H. W.; Hicks, D. G.; Holder, J. P.; Holunga, D. M.; Horner, J. B.; Hsing, W. W.; Huang, H.; Jackson, M. C.; Jancaitis, K. S.; Kalantar, D. H.; Kauffman, R. L.; Kauffman, M. I.; Khan, S. F.; Kilkenny, J. D.; Kimbrough, J. R.; Kirkwood, R.; Kline, J. L.; Knauer, J. P.; Knittel, K. M.; Koch, J. A.; Kohut, T. R.; Kozioziemski, B. J.; Krauter, K.; Krauter, G. W.; Kritcher, A. L.; Kroll, J.; Kyrala, G. A.; Fortune, K. N. La; LaCaille, G.; Lagin, L. J.; Land, T. A.; Landen, O. L.; Larson, D. W.; Latray, D. A.; Leeper, R. J.; Lewis, T. L.; LePape, S.; Lindl, J. D.; Lowe-Webb, R. R.; Ma, T.; MacGowan, B. J.; MacKinnon, A. J.; MacPhee, A. G.; Malone, R. M.; Malsbury, T. N.; Mapoles, E.; Marshall, C. D.; Mathisen, D. G.; McKenty, P.; McNaney, J. M.; Meezan, N. B.; Michel, P.; Milovich, J. L.; Moody, J. D.; Moore, A. S.; Moran, M. J.; Moreno, K.; Moses, E. I.; Munro, D. H.; Nathan, B. R.; Nelson, A. J.; Nikroo, A.; Olson, R. E.; Orth, C.; Pak, A. E.; Palma, E. S.; Parham, T. G.; Patel, P. K.; Patterson, R. W.; Petrasso, R. D.; Prasad, R.; Ralph, J. E.; Regan, S. P.; Rinderknecht, H.; Robey, H. F.; Ross, G. F.; Ruiz, C. L.; Seguin, F. H.; Salmonson, J. D.; Sangster, T. C.; Sater, J. D.; Saunders, R. L.; Schneider, M. B.; Schneider, D. H.; Shaw, M. J.; Simanovskaia, N.; Spears, B. K.; Springer, P. T.; Stoeckl, C.; Stoeffl, W.; Suter, L. J.; Thomas, C. A.; Tommasini, R.; Town, R. P.; Traille, A. J.; Wonterghem, B. Van; Wallace, R. J.; Weaver, S.; Weber, S. V.; Wegner, P. J.; Whitman, P. K.; Widmann, K.; Widmayer, C. C.; Wood, R. D.; Young, B. K.; Zacharias, R. A.; Zylstra, A.

2013-05-01

First results from the analysis of neutron image data collected on implosions of cryogenically layered deuterium-tritium capsules during the 2011-2012 National Ignition Campaign are reported. The data span a variety of experimental designs aimed at increasing the stagnation pressure of the central hotspot and areal density of the surrounding fuel assembly. Images of neutrons produced by deuterium–tritium fusion reactions in the hotspot are presented, as well as images of neutrons that scatter in the surrounding dense fuel assembly. The image data are compared with 1D and 2D model predictions, and consistency checked using other diagnostic data. The results indicate that the size of the fusing hotspot is consistent with the model predictions, as well as other imaging data, while the overall size of the fuel assembly, inferred from the scattered neutron images, is systematically smaller than models’ prediction. Preliminary studies indicate these differences are consistent with a significant fraction (20%–25%) of the initial deuterium-tritium fuel mass outside the compact fuel assembly, due either to low mode mass asymmetry or high mode 3D mix effects at the ablator-ice interface.

Nuclear imaging of the fuel assembly in ignition experiments

Energy Technology Data Exchange (ETDEWEB)

Grim, G. P.; Guler, N.; Merrill, F. E.; Morgan, G. L.; Danly, C. R.; Volegov, P. L.; Wilde, C. H.; Wilson, D. C.; Batha, S.; Herrmann, H. W.; Kline, J. L.; Kyrala, G. A. [Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States); Clark, D. S.; Hinkel, D. E.; Jones, O. S.; Raman, K. S.; Izumi, N.; Fittinghoff, D. N.; Drury, O. B.; Alger, E. T. [Lawrence Livermore National Laboratory, Livermore, California 94551-0808 (United States); and others

2013-05-15

First results from the analysis of neutron image data collected on implosions of cryogenically layered deuterium-tritium capsules during the 2011-2012 National Ignition Campaign are reported. The data span a variety of experimental designs aimed at increasing the stagnation pressure of the central hotspot and areal density of the surrounding fuel assembly. Images of neutrons produced by deuterium–tritium fusion reactions in the hotspot are presented, as well as images of neutrons that scatter in the surrounding dense fuel assembly. The image data are compared with 1D and 2D model predictions, and consistency checked using other diagnostic data. The results indicate that the size of the fusing hotspot is consistent with the model predictions, as well as other imaging data, while the overall size of the fuel assembly, inferred from the scattered neutron images, is systematically smaller than models' prediction. Preliminary studies indicate these differences are consistent with a significant fraction (20%–25%) of the initial deuterium-tritium fuel mass outside the compact fuel assembly, due either to low mode mass asymmetry or high mode 3D mix effects at the ablator-ice interface.

A planar PDMS micropump using in-contact minimized-leakage check valves

International Nuclear Information System (INIS)

Ni, Junhui; Li, Beizhi; Huang, Fengliang; Wang, Bin; Lin, Qiao

2010-01-01

We present a micropump with a simple planar design featuring compliant in-contact check valves in a single layer, which allows for a simple structure and easy system integration. The micropump, based on poly(dimethylsiloxane) (PDMS), primarily consists of a pneumatically driven thin membrane, a pump chamber, and two in-plane check valves. The pair of check valves is based on an in-contact flap–stopper configuration and is able to minimize leakage flow, greatly enhancing the reliability and performance of the micropump. Systematic experimental characterization of the micropump has been performed in terms of the frequency response of the pumping flow rate with respect to factors including device geometry (e.g. chamber height) and operating parameters (e.g. pneumatic driving pressure and backpressure). The results demonstrate that this micropump is capable of reliably generating a maximum flow rate of 41 µL min −1 and operating against a high backpressure of up to 25 kPa. In addition, a lumped-parameter theoretical model for the planar micropump is also developed for accurate analysis of the device behavior. These results demonstrate the capability of this micropump for diverse applications in lab-on-a-chip systems.

Compositional and Quantitative Model Checking

DEFF Research Database (Denmark)

Larsen, Kim Guldstrand

2010-01-01

This paper gives a survey of a composition model checking methodology and its succesfull instantiation to the model checking of networks of finite-state, timed, hybrid and probabilistic systems with respect; to suitable quantitative versions of the modal mu-calculus [Koz82]. The method is based...

Goat production check list

DEFF Research Database (Denmark)

Henriksen, Jørgen; Nielsen, Mette Benedicte Olaf; Madsen, Jørgen

2009-01-01

This check list, financed by DanChurchAid, highlights all issues should be carefully investigated before investing in distribution of goats and in interventions to assist poor rural communities to improve their livelihood through goat production.......This check list, financed by DanChurchAid, highlights all issues should be carefully investigated before investing in distribution of goats and in interventions to assist poor rural communities to improve their livelihood through goat production....

12 CFR Appendix A to Part 229 - Routing Number Guide to Next-Day Availability Checks and Local Checks

Science.gov (United States)

2010-01-01

... Checks and Local Checks A Appendix A to Part 229 Banks and Banking FEDERAL RESERVE SYSTEM (CONTINUED) BOARD OF GOVERNORS OF THE FEDERAL RESERVE SYSTEM AVAILABILITY OF FUNDS AND COLLECTION OF CHECKS... Association. The routing number takes two forms: a fractional form and a nine-digit form. A paying bank...

Model Checking Real-Time Systems

DEFF Research Database (Denmark)

Bouyer, Patricia; Fahrenberg, Uli; Larsen, Kim Guldstrand

2018-01-01

This chapter surveys timed automata as a formalism for model checking real-time systems. We begin with introducing the model, as an extension of finite-state automata with real-valued variables for measuring time. We then present the main model-checking results in this framework, and give a hint...

Can i just check...? Effects of edit check questions on measurement error and survey estimates

NARCIS (Netherlands)

Lugtig, Peter; Jäckle, Annette

2014-01-01

Household income is difficult to measure, since it requires the collection of information about all potential income sources for each member of a household.Weassess the effects of two types of edit check questions on measurement error and survey estimates: within-wave edit checks use responses to

Model-Checking Discrete Duration Calculus

DEFF Research Database (Denmark)

Hansen, Michael Reichhardt

1994-01-01

can do model-checking. The subset we consider is expressive enough to formalize the requirements to the gas burner system given by A.P. Ravn (1993); but only for a discrete time domain. Model-checking is done by reducing the correctness problem ℳ|=𝒟 to the inclusion problem of regular...

Assembly and metrology of first wall components of SST-1

International Nuclear Information System (INIS)

Parekh, Tejas; Santra, Prosenjit; Biswas, Prabal

2015-01-01

First Wall components (FWC) of SST-1 tokamak, which are in the immediate vicinity of plasma comprises of limiters, divertors, baffles, passive stabilizers are designed to operate long duration (1000 s) discharges of elongated plasma. All FWC consists of a copper alloy heat sink modules with SS cooling tubes brazed onto it, graphite tiles acting as armour material facing the plasma, and are mounted to the vacuum vessels with suitable Inconel support structures at ring and port locations. The FWC are very recently assembled and commissioned successfully inside the vacuum vessel of SST-1 under going a meticulous planning of assembly sequence, quality checks at every stage of the assembly process. This paper will present the metrology aspects and procedure of each FWC, both outside the vacuum vessel, and inside the vessel, assembly tolerances, tools, equipment and jig/fixtures, used at each stage of assembly, starting from location of support bases on vessel rings, fixing of copper modules on support structures, around 3800 graphite tile mounting on 136 copper modules with proper tightening torques, till final toroidal and poloidal geometry of the in-vessel components are obtained within acceptable limits, also ensuring electrical continuity of passive stabilizers to form a closed saddle loop, electrical isolation of passive stabilizers from vacuum vessel. (author)

a Design of the Driver Airbag Module with Floating Horn Assembly

Science.gov (United States)

Suh, Chang-Min; Lee, Young-Hoon; Suh, Duck-Young

The driver airbag system is designed as a supplemental restraint system in addition to the seatbelt, and is designed to protect the driver's head and chest against severe injury by a device that is actuated in case of vehicle's fronted impact. Deployment of an airbag module with floating horn assembly is a highly dynamic process. The concept of driver airbag module with floating horn assembly and aluminum emblem is presented as a useful parameter when the airbag deploys and the energy is evaluated as performance factor in airbag module. Floating horn assembly is also one of the major factors for driver airbag module design to perform its horn function and check the package between driver airbag module and steering wheel. This study on the design of driver airbag module with floating horn assembly proved the feasibility as a new safety device. However, the system level study is needed for decrease of passenger injury. This study can be used for the implementation of a prototype of DABM with floating horn device.

On Simplification of Database Integrity Constraints

DEFF Research Database (Denmark)

Christiansen, Henning; Martinenghi, Davide

2006-01-01

Without proper simplification techniques, database integrity checking can be prohibitively time consuming. Several methods have been developed for producing simplified incremental checks for each update but none until now of sufficient quality and generality for providing a true practical impact,...

31 CFR 248.6 - Recovery of original check.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 2 2010-07-01 2010-07-01 false Recovery of original check. 248.6... § 248.6 Recovery of original check. (a) If the claimant recovers an original check after he has... or agency concerned regarding the negotiability of such original check. (b) In the event the...

CMM Interim Check (U)

Energy Technology Data Exchange (ETDEWEB)

Montano, Joshua Daniel [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-03-23

Coordinate Measuring Machines (CMM) are widely used in industry, throughout the Nuclear Weapons Complex and at Los Alamos National Laboratory (LANL) to verify part conformance to design definition. Calibration cycles for CMMs at LANL are predominantly one year in length. Unfortunately, several nonconformance reports have been generated to document the discovery of a certified machine found out of tolerance during a calibration closeout. In an effort to reduce risk to product quality two solutions were proposed – shorten the calibration cycle which could be costly, or perform an interim check to monitor the machine’s performance between cycles. The CMM interim check discussed makes use of Renishaw’s Machine Checking Gauge. This off-the-shelf product simulates a large sphere within a CMM’s measurement volume and allows for error estimation. Data was gathered, analyzed, and simulated from seven machines in seventeen different configurations to create statistical process control run charts for on-the-floor monitoring.

Commissioning of the STAR test section for experimental simulation of loss of coolant accident using the EC-208 instrumented fuel assembly of the IEA-R1 reactor

Energy Technology Data Exchange (ETDEWEB)

Maprelian, Eduardo; Torres, Walmir M.; Prado, Adelk C.; Umbehaun, Pedro E.; Franca, Renato L.; Santos, Samuel C.; Macedo, Luiz A.; Sabundjian, Gaiane, E-mail: emaprel@ipen.br, E-mail: wmtorres@ipen.br, E-mail: acprado@ipen.br, E-mail: umbehaun@ipen.br, E-mail: rlfranca@ipen.br, E-mail: samuelcs@ipen.br, E-mail: lamacedo@ipen.br, E-mail: gdjian@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SO (Brazil)

2015-07-01

The three basic safety functions of Research Reactors (RR) are the safe shutdown of the reactor, the proper cooling of the decay heat of the fuel elements and the confinement of radioactive materials. Compared to Nuclear Power Reactors, RR power release is small, yet its three safety functions must be met to ensure the integrity of the reactor. During a loss of coolant accident (LOCA) in pool type RR, partial or complete loss of pool water may occur, with consequent partial or complete uncovering of the fuel assemblies. In such an accident, the decay heat removal safety function must not be compromised. The Test Section for Experimental Simulation of Loss of Coolant Accident (STAR) is in commissioning phase. This test section will provide experimental data on partial and total uncovering of the EC-208 instrumented fuel assembly (IFA) irradiated in the IEA-R1. Experimental results will be useful in validation of computer codes for RR safety analysis, particularly on heat removal efficiency aspects (safety function) in accident conditions. STAR comprises a base on which is installed the IFA, the cylindrical stainless steel hull, the compressed air system for the test section emptying and refilling, and the instrumentation for temperature and level measurements. The commissioning tests or pre-operational check, consist of several preliminary tests to verify experimental procedures, the difficulties during assembling of STAR in the pool, the difficulties in control the emptying and refilling velocities, as well as, the repeatability capacity, tests of equipment, valves and systems and tests of instrumentation and data acquisition system. Safety, accuracy and easiness of operation will be checked. (author)

Environmental Reality Check.

Science.gov (United States)

Manicone, Santo

2001-01-01

Discusses the importance of educational facilities conducting "reality check" self-audits to uncover the real truth behind underlying environmental problems. An environmental compliance multimedia checklist is included. (GR)

Quantifying quality in DNA self-assembly

Science.gov (United States)

Wagenbauer, Klaus F.; Wachauf, Christian H.; Dietz, Hendrik

2014-01-01

Molecular self-assembly with DNA is an attractive route for building nanoscale devices. The development of sophisticated and precise objects with this technique requires detailed experimental feedback on the structure and composition of assembled objects. Here we report a sensitive assay for the quality of assembly. The method relies on measuring the content of unpaired DNA bases in self-assembled DNA objects using a fluorescent de-Bruijn probe for three-base ‘codons’, which enables a comparison with the designed content of unpaired DNA. We use the assay to measure the quality of assembly of several multilayer DNA origami objects and illustrate the use of the assay for the rational refinement of assembly protocols. Our data suggests that large and complex objects like multilayer DNA origami can be made with high strand integration quality up to 99%. Beyond DNA nanotechnology, we speculate that the ability to discriminate unpaired from paired nucleic acids in the same macromolecule may also be useful for analysing cellular nucleic acids. PMID:24751596

Deterministic nanoparticle assemblies: from substrate to solution

International Nuclear Information System (INIS)

Barcelo, Steven J; Gibson, Gary A; Yamakawa, Mineo; Li, Zhiyong; Kim, Ansoon; Norris, Kate J

2014-01-01

The deterministic assembly of metallic nanoparticles is an exciting field with many potential benefits. Many promising techniques have been developed, but challenges remain, particularly for the assembly of larger nanoparticles which often have more interesting plasmonic properties. Here we present a scalable process combining the strengths of top down and bottom up fabrication to generate deterministic 2D assemblies of metallic nanoparticles and demonstrate their stable transfer to solution. Scanning electron and high-resolution transmission electron microscopy studies of these assemblies suggested the formation of nanobridges between touching nanoparticles that hold them together so as to maintain the integrity of the assembly throughout the transfer process. The application of these nanoparticle assemblies as solution-based surface-enhanced Raman scattering (SERS) materials is demonstrated by trapping analyte molecules in the nanoparticle gaps during assembly, yielding uniformly high enhancement factors at all stages of the fabrication process. (paper)

Digital gene expression analysis based on integrated de novo transcriptome assembly of sweet potato [Ipomoea batatas (L. Lam].

Directory of Open Access Journals (Sweden)

Xiang Tao

Full Text Available BACKGROUND: Sweet potato (Ipomoea batatas L. [Lam.] ranks among the top six most important food crops in the world. It is widely grown throughout the world with high and stable yield, strong adaptability, rich nutrient content, and multiple uses. However, little is known about the molecular biology of this important non-model organism due to lack of genomic resources. Hence, studies based on high-throughput sequencing technologies are needed to get a comprehensive and integrated genomic resource and better understanding of gene expression patterns in different tissues and at various developmental stages. METHODOLOGY/PRINCIPAL FINDINGS: Illumina paired-end (PE RNA-Sequencing was performed, and generated 48.7 million of 75 bp PE reads. These reads were de novo assembled into 128,052 transcripts (≥ 100 bp, which correspond to 41.1 million base pairs, by using a combined assembly strategy. Transcripts were annotated by Blast2GO and 51,763 transcripts got BLASTX hits, in which 39,677 transcripts have GO terms and 14,117 have ECs that are associated with 147 KEGG pathways. Furthermore, transcriptome differences of seven tissues were analyzed by using Illumina digital gene expression (DGE tag profiling and numerous differentially and specifically expressed transcripts were identified. Moreover, the expression characteristics of genes involved in viral genomes, starch metabolism and potential stress tolerance and insect resistance were also identified. CONCLUSIONS/SIGNIFICANCE: The combined de novo transcriptome assembly strategy can be applied to other organisms whose reference genomes are not available. The data provided here represent the most comprehensive and integrated genomic resources for cloning and identifying genes of interest in sweet potato. Characterization of sweet potato transcriptome provides an effective tool for better understanding the molecular mechanisms of cellular processes including development of leaves and storage roots

7 CFR 1944.540 - Requesting TSA checks.

Science.gov (United States)

2010-01-01

... 7 Agriculture 13 2010-01-01 2009-01-01 true Requesting TSA checks. 1944.540 Section 1944.540... TSA checks. (a) The initial TSA check may cover the applicant's needs for the first calendar month. If... the next whole month. (b) The initial advance of TSA grant funds may not be requested simultaneously...

An integrated approach for determining plutonium mass in spent fuel assemblies with nondestructive assay

International Nuclear Information System (INIS)

Swinhoe, Martyn T.; Tobin, Stephen J.; Fensin, Mike L.; Menlove, Howard O.

2009-01-01

be part of a system that cost-effectively meets the burnup credit needs of a repository. Behind each of these reasons is a regulatory structure with MC and A requirements. In the case of the IAEA, the accountable quantity is elemental plutonium. The material in spent fuel (fissile isotopes, fission products, etc.) emits signatures that provide information about the content and history of the fuel. A variety of nondestructive assay (NDA) techniques are available to quantify these signatures. The effort presented in this paper is investigation of the capabilities of 12 NDA techniques. For these 12, none is conceptually capable of independently determining the Pu content in a spent fuel assembly while at the same time being able to detect the diversion of a significant quantity of rods. For this reason the authors are investigating the capability of 12 NDA techniques with the end goal of integrating a few techniques together into a system that is capable of measuring Pu mass in an assembly. The work described here is the beginning of what is anticipated to be a five year effort: (1) two years of modeling to select the best technologies, (2) one year fabricating instruments and (3) two years measuring spent fuel. This paper describes the first two years of this work. In order to cost effectively and robustly model the performance of the 12 NDA techniques, an 'assembly library' was created. The library contains the following: (a) A diverse range of PWR spent fuel assemblies (burnup, enrichment, cooling time) similar to that which exists in spent pools today and in the future. (b) Diversion scenarios that capture a range of possible rod removal options. (c) The spatial and isotopic detail needed to accurately quantify the capability of all the NDA techniques so as to enable integration. It is our intention to make this library available to other researchers in the field for inter-comparison purposes. The performance of each instrument will be quantified for the full

40 CFR 86.328-79 - Leak checks.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Leak checks. 86.328-79 Section 86.328... Gasoline-Fueled and Diesel-Fueled Heavy-Duty Engines; Gaseous Exhaust Test Procedures § 86.328-79 Leak checks. (a) Vacuum side leak check. (1) Any location within the analysis system where a vacuum leak could...

Swing check valve

International Nuclear Information System (INIS)

Eminger, H.E.

1977-01-01

A swing check valve which includes a valve body having an inlet and outlet is described. A recess in the valve body designed to hold a seal ring and a check valve disc swingable between open and closed positions. The disc is supported by a high strength wire secured at one end in a support spacer pinned through bearing blocks fixed to the valve body and at its other end in a groove formed on the outer peripheral surface of the disc. The parts are designed and chosen such to provide a lightweight valve disc which is held open by minimum velocity of fluid flowing through the valve which thus reduces oscillations and accompanying wear of bearings supporting the valve operating parts. (Auth.)

Integrative structure modeling with the Integrative Modeling Platform.

Science.gov (United States)

Webb, Benjamin; Viswanath, Shruthi; Bonomi, Massimiliano; Pellarin, Riccardo; Greenberg, Charles H; Saltzberg, Daniel; Sali, Andrej

2018-01-01

Building models of a biological system that are consistent with the myriad data available is one of the key challenges in biology. Modeling the structure and dynamics of macromolecular assemblies, for example, can give insights into how biological systems work, evolved, might be controlled, and even designed. Integrative structure modeling casts the building of structural models as a computational optimization problem, for which information about the assembly is encoded into a scoring function that evaluates candidate models. Here, we describe our open source software suite for integrative structure modeling, Integrative Modeling Platform (https://integrativemodeling.org), and demonstrate its use. © 2017 The Protein Society.

De Novo Genome and Transcriptome Assembly of the Canadian Beaver (Castor canadensis

Directory of Open Access Journals (Sweden)

Si Lok

2017-02-01

Full Text Available The Canadian beaver (Castor canadensis is the largest indigenous rodent in North America. We report a draft annotated assembly of the beaver genome, the first for a large rodent and the first mammalian genome assembled directly from uncorrected and moderate coverage (< 30 × long reads generated by single-molecule sequencing. The genome size is 2.7 Gb estimated by k-mer analysis. We assembled the beaver genome using the new Canu assembler optimized for noisy reads. The resulting assembly was refined using Pilon supported by short reads (80 × and checked for accuracy by congruency against an independent short read assembly. We scaffolded the assembly using the exon–gene models derived from 9805 full-length open reading frames (FL-ORFs constructed from the beaver leukocyte and muscle transcriptomes. The final assembly comprised 22,515 contigs with an N50 of 278,680 bp and an N50-scaffold of 317,558 bp. Maximum contig and scaffold lengths were 3.3 and 4.2 Mb, respectively, with a combined scaffold length representing 92% of the estimated genome size. The completeness and accuracy of the scaffold assembly was demonstrated by the precise exon placement for 91.1% of the 9805 assembled FL-ORFs and 83.1% of the BUSCO (Benchmarking Universal Single-Copy Orthologs gene set used to assess the quality of genome assemblies. Well-represented were genes involved in dentition and enamel deposition, defining characteristics of rodents with which the beaver is well-endowed. The study provides insights for genome assembly and an important genomics resource for Castoridae and rodent evolutionary biology.

Plant experience with check valves in passive systems

Energy Technology Data Exchange (ETDEWEB)

Pahladsingh, R R [GKN Joint Nuclear Power Plant, Dodewaard (Netherlands)

1996-12-01

In the design of the advanced nuclear reactors there is a tendency to introduce more passive safety systems. The 25 year old design of the GKN nuclear reactor is different from the present BWR reactors because of some special features, such as the Natural Circulation - and the Passive Isolation Condenser system. When reviewing the design, one can conclude that the plant has 25 years of experience with check valves in passive systems and as passive components in systems. The result of this experience has been modeled in a plant-specific ``living PSA`` for the plant. A data-analysis has been performed on components which are related to the safety systems in the plant. As part of this study also the check valves have been taken in consideration. At GKN, the check valves have shown to be reliable components in the systems and no catastrophic failures have been experienced during the 25 years of operation. Especially the Isolation Condenser with its operation experience can contribute substantially to the insight of check valves in stand-by position at reactor pressure and operating by gravity under different pressure conditions. With the introduction of several passive systems in the SBWR-600 design, such as the Isolation Condensers, Gravity Driven Cooling, and Suppression Pool Cooling System, the issue of reliability of check valves in these systems is actual. Some critical aspects for study in connection with check valves are: What is the reliability of a check valve in a system at reactor pressure, to open on demand; what is the reliability of a check valve in a system at low pressure (gravity), to open on demand; what is the reliability of a check valve to open/close when the stand-by check wave is at zero differential pressure. The plant experience with check valves in a few essential safety systems is described and a brief introduction will be made about the application of check valves in the design of the new generation reactors is given. (author). 6 figs, 1 tab.

DEPUTY: analysing architectural structures and checking style

International Nuclear Information System (INIS)

Gorshkov, D.; Kochelev, S.; Kotegov, S.; Pavlov, I.; Pravilnikov, V.; Wellisch, J.P.

2001-01-01

The DepUty (dependencies utility) can be classified as a project and process management tool. The main goal of DepUty is to assist by means of source code analysis and graphical representation using UML, in understanding dependencies of sub-systems and packages in CMS Object Oriented software, to understand architectural structure, and to schedule code release in modularised integration. It also allows a new-comer to more easily understand the global structure of CMS software, and to void circular dependencies up-front or re-factor the code, in case it was already too close to the edge of non-maintainability. The authors will discuss the various views DepUty provides to analyse package dependencies, and illustrate both the metrics and style checking facilities it provides

Automatization and familiarity in repeated checking

NARCIS (Netherlands)

Dek, E.C.P.|info:eu-repo/dai/nl/313959552; van den Hout, M.A.|info:eu-repo/dai/nl/070445354; Giele, C.L.|info:eu-repo/dai/nl/318754460; Engelhard, I.M.|info:eu-repo/dai/nl/239681533

2015-01-01

Repetitive, compulsive-like checking of an object leads to reductions in memory confidence, vividness, and detail. Experimental research suggests that this is caused by increased familiarity with perceptual characteristics of the stimulus and automatization of the checking procedure (Dek, van den

Simplification of integrity constraints for data integration

DEFF Research Database (Denmark)

Christiansen, Henning; Martinenghi, Davide

2004-01-01

, because either the global database is known to be consistent or suitable actions have been taken to provide consistent views. The present work generalizes simplification techniques for integrity checking in traditional databases to the combined case. Knowledge of local consistency is employed, perhaps...

ENDF-UTILITY-CODES, codes to check and standardize data in the Evaluated Nuclear Data File (ENDF)

International Nuclear Information System (INIS)

Dunford, Charles L.

2007-01-01

1 - Description of program or function: The ENDF Utility Codes include 9 codes to check and standardize data in the Evaluated Nuclear Data File (ENDF). Four programs of this release, GETMAT, LISTEF, PLOTEF and SETMDC are no more maintained since release 6.13. The suite of ENDF utility codes includes: - CHECKR (version 7.01) is a program for checking that an evaluated data file conforms to the ENDF format. - FIZCON (version 7.02) is a program for checking that an evaluated data file has valid data and conforms to recommended procedures. - GETMAT (version 6.13) is designed to retrieve one or more materials from an ENDF formatted data file. The output will contain only the selected materials. - INTER (version 7.01) calculates thermal cross sections, g-factors, resonance integrals, fission spectrum averaged cross sections and 14.0 MeV (or other energy) cross sections for major reactions in an ENDF-6 or ENDF-5 format data file. - LISTEF (version 6.13) is designed to produce summary and annotated listings of a data file in either ENDF-6 or ENDF-5 format. - PLOTEF (version 6.13) is designed to produce graphical displays of a data file in either ENDF-5 or ENDF-6 format. The form of graphical output depends on the graphical devices available at the installation where this code will be used. - PSYCHE (version 7.02) is a program for checking the physics content of an evaluated data file. It can recognise the difference between ENDF-5 or ENDF-6 formats and performs its tests accordingly. - SETMDC (version 6.13) is a utility program that converts the source decks of programs to different computers (DOS, UNIX, LINUX, VMS, Windows). - STANEF (version 7.01) performs bookkeeping operations on a data file containing one or more material evaluations in ENDF format. The version 7.02 of the ENDF Utility Codes corrects all bugs reported to NNDC as of April 1, 2005 and supersedes all previous releases. Three codes CHECKR, STANEF, and INTER were actually ported from the 7.01 release

Diagnostic information in temporal compliance checking

NARCIS (Netherlands)

Ramezani Taghiabadi, E.; Fahland, D.; Dongen, van B.F.; Aalst, van der W.M.P.

2012-01-01

Compliance checking is gaining importance as today’s organizations need to show that operational processes are executed in a controlled manner while satisfying prede¿ned (legal) requirements. Deviations may be costly and expose the organization to severe risks. Compliance checking is of growing

31 CFR 245.8 - Receipt or recovery of original check.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 2 2010-07-01 2010-07-01 false Receipt or recovery of original check... CHECKS § 245.8 Receipt or recovery of original check. (a) If the original check is received or recovered... of instructions with respect to the negotiability of such check. (b) If the original check is...

Forgetting what you have checked: a link between working memory impairment and checking behaviors in obsessive-compulsive disorder.

Science.gov (United States)

Jaafari, N; Frasca, M; Rigalleau, F; Rachid, F; Gil, R; Olié, J-P; Guehl, D; Burbaud, P; Aouizerate, B; Rotgé, J-Y; Vibert, N

2013-02-01

Compulsive checking behaviors are common in obsessive-compulsive disorder (OCD). Several authors have suggested that these checking rituals could be related to memory deficits. Our aim was to test whether patients with OCD show working memory impairment in relation to their checking behavior. We evaluated the verbal and visuospatial components of patients' and controls' working memory using the reading span and backward location span tests. Checking behaviors were measured by recording participants' eye movements during an image comparison task using a non-invasive, infra-red TOBII 1750 eyetracker. Participants were seated, head-free, in a natural position in front of the eyetracker screen where the images were displayed. Patients with OCD made more gaze moves to compare images than controls. Both patients' working memory spans were reduced, and the patients' deficit in the comparison task was negatively related to their working memory spans. This work demonstrates that checking behavior in OCD is linked to a general reduction of the patients' verbal and visuospatial working memory span. Copyright © 2011 Elsevier Masson SAS. All rights reserved.

Integrating Test-Form Formatting into Automated Test Assembly

Science.gov (United States)

Diao, Qi; van der Linden, Wim J.

2013-01-01

Automated test assembly uses the methodology of mixed integer programming to select an optimal set of items from an item bank. Automated test-form generation uses the same methodology to optimally order the items and format the test form. From an optimization point of view, production of fully formatted test forms directly from the item pool using…

Model Checking Infinite-State Markov Chains

NARCIS (Netherlands)

Remke, Anne Katharina Ingrid; Haverkort, Boudewijn R.H.M.; Cloth, L.

2004-01-01

In this paper algorithms for model checking CSL (continuous stochastic logic) against infinite-state continuous-time Markov chains of so-called quasi birth-death type are developed. In doing so we extend the applicability of CSL model checking beyond the recently proposed case for finite-state

38 CFR 21.4505 - Check delivery.

Science.gov (United States)

2010-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false Check delivery. 21.4505...) VOCATIONAL REHABILITATION AND EDUCATION Education Loans § 21.4505 Check delivery. (a) General. Education... surviving spouse is enrolled for delivery by the educational institution. (b) Delivery and certification. (1...

check cif.pdf

Indian Academy of Sciences (India)

AMMIN

Calculated. Reported. Volume ... PLAT094_ALERT_2_C Ratio of Maximum / Minimum Residual Density .... 3.24 Report ... checkCIF was carefully designed to identify outliers and unusual parameters, but every test has its limitations and alerts ...

46 CFR 10.214 - Security Check.

Science.gov (United States)

2010-10-01

... 46 Shipping 1 2010-10-01 2010-10-01 false Security Check. 10.214 Section 10.214 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY MERCHANT MARINE OFFICERS AND SEAMEN MERCHANT MARINER CREDENTIAL General Requirements for All Merchant Mariner Credentials § 10.214 Security Check. Until April 15, 2009...

An assembly sequence planning method based on composite algorithm

Directory of Open Access Journals (Sweden)

Enfu LIU

2016-02-01

Full Text Available To solve the combination explosion problem and the blind searching problem in assembly sequence planning of complex products, an assembly sequence planning method based on composite algorithm is proposed. In the composite algorithm, a sufficient number of feasible assembly sequences are generated using formalization reasoning algorithm as the initial population of genetic algorithm. Then fuzzy knowledge of assembly is integrated into the planning process of genetic algorithm and ant algorithm to get the accurate solution. At last, an example is conducted to verify the feasibility of composite algorithm.

A participatory and integrative approach to increase productivity and comfort in assembly

NARCIS (Netherlands)

Looze, M.P. de; Rhijn, G. van; Tuinzaad, B.; Deursen, J. van

2000-01-01

Manufacturers of manually assembled products are more and more forced to improve the flow of assembly orders together with a more efficient employment, in order to meet increasing demands on short delivery times, high product variety, good quality and low manufacturing costs. At the same time, the

7 CFR 58.243 - Checking quality.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Checking quality. 58.243 Section 58.243 Agriculture... Procedures § 58.243 Checking quality. All milk, milk products and dry milk products shall be subject to inspection and analysis by the dairy plant for quality and condition throughout each processing operation...

Liaison based assembly design

Energy Technology Data Exchange (ETDEWEB)

Ames, A.; Kholwadwala, D.; Wilson, R.H.

1996-12-01

Liaison Based Assembly Design extends the current information infrastructure to support design in terms of kinematic relationships between parts, or liaisons. These liaisons capture information regarding contact, degrees-of-freedom constraints and containment relationships between parts in an assembly. The project involved defining a useful collection of liaison representations, investigating their properties, and providing for maximum use of the data in downstream applications. We tested our ideas by implementing a prototype system involving extensions to Pro/Engineer and the Archimedes assembly planner. With an expanded product model, the design system is more able to capture design intent. When a product update is attempted, increased knowledge availability improves our ability to understand the effect of design changes. Manufacturing and analysis disciplines benefit from having liaison information available, so less time is wasted arguing over incomplete design specifications and our enterprise can be more completely integrated.

Mothers' use of and attitudes to BabyCheck.

OpenAIRE

Thomson, Hilary; Ross, Sue; Wilson, Philip; McConnachie, Alex; Watson, Richard

2002-01-01

A copy of BabyCheck was sent to 497 mothers shortly after the birth of their baby. Six months later they were sent a questionnaire asking about their use of and attitudes to, BabyCheck. Questionnaires were returned by 323 (65%) mothers; 215 (67%) of them reported reading BabyCheck, the majority found it easy to understand (74%) and agreed with the advice (67%). Eighty-four (26%) of the mothers who returned the questionnaires reported using BabyCheck when their baby was ill; of these, 71% agre...

CMM Interim Check Design of Experiments (U)

Energy Technology Data Exchange (ETDEWEB)

Montano, Joshua Daniel [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-07-29

Coordinate Measuring Machines (CMM) are widely used in industry, throughout the Nuclear Weapons Complex and at Los Alamos National Laboratory (LANL) to verify part conformance to design definition. Calibration cycles for CMMs at LANL are predominantly one year in length and include a weekly interim check to reduce risk. The CMM interim check makes use of Renishaw’s Machine Checking Gauge which is an off-the-shelf product simulates a large sphere within a CMM’s measurement volume and allows for error estimation. As verification on the interim check process a design of experiments investigation was proposed to test a couple of key factors (location and inspector). The results from the two-factor factorial experiment proved that location influenced results more than the inspector or interaction.

7 CFR 1421.11 - Spot checks.

Science.gov (United States)

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false Spot checks. 1421.11 Section 1421.11 Agriculture... ASSISTANCE LOANS AND LOAN DEFICIENCY PAYMENTS FOR 2008 THROUGH 2012 General § 1421.11 Spot checks. (a) CCC... CCC access to the farm and storage facility as necessary to conduct collateral inspections, or “spot...

32 CFR 635.6 - Name checks.

Science.gov (United States)

2010-07-01

... 32 National Defense 4 2010-07-01 2010-07-01 true Name checks. 635.6 Section 635.6 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) LAW ENFORCEMENT AND CRIMINAL INVESTIGATIONS LAW ENFORCEMENT REPORTING Records Administration § 635.6 Name checks. (a) Information contained in military police records may be...

45 CFR 201.70 - Treatment of replacement checks.

Science.gov (United States)

2010-10-01

... 45 Public Welfare 2 2010-10-01 2010-10-01 false Treatment of replacement checks. 201.70 Section... STATES FOR PUBLIC ASSISTANCE PROGRAMS Review and Audits § 201.70 Treatment of replacement checks. (a... (FFP) for replacement checks under titles I, VI-A, X, XIV, XVI (AABD) except under the circumstances...

Recent improvements in check valve monitoring methods

International Nuclear Information System (INIS)

Haynes, H.D.

1991-01-01

In support of the NRC Nuclear Plant Aging Research (NPAR) program, ORNL has carried out an evaluation of three check valve monitoring methods: acoustic emission, ultrasonic inspection, and magnetic flux signature analysis (MFSA). This work has focussed on determining the capabilities of each method to provide diagnostic information useful in determining check valve aging and service wear effects (degradation) and undesirable operating modes. In addition, as part of the ORNL Advanced Diagnostic Engineering Research and Development Center (ADEC), two novel nonintrusive monitoring methods were developed (external ac- and dc-magnetic monitoring) that provide several improvements over the other methods. None of the examined methods could, by themselves, monitor the instantaneous position and motion of check valve internals and valve leakage; however, the combination of acoustic emission monitoring with one of the other methods provides the means to determine vital check valve operational information. This paper describes the benefits and limitations associated with each method and includes recent laboratory and field test data to illustrate the capabilities of these methods to detect simulated check valve degradation. 3 refs., 22 figs., 4 tabs

Recent improvements in check valve monitoring methods

International Nuclear Information System (INIS)

Haynes, H.D.

1990-01-01

In support of the NRC Nuclear Plant Aging Research (NPAR) program, ORNL has carried out an evaluation of three check valve monitoring methods: acoustic emission, ultrasonic inspection, and magnetic flux signature analysis (MFSA). This work has focused on determining the capabilities of each method to provide diagnostic information useful in determining check valve aging and service wear effects (degradation) and undesirable operating modes. In addition, as part of the ORNL Advanced Diagnostic Engineering Research and Development Center (ADEC), two noval nonintrusive monitoring methods were developed (external ac- and dc-magnetic monitoring) that provide several improvements over the other methods. None of the examined methods could, by themselves, monitor the instantaneous position and motion of check valve internals and valve leakage; however, the combination of acoustic emission monitoring with one of the other methods provides the means to determine vital check valve operational information. This paper describes the benefits and limitations associated with each method and includes recent laboratory and field test data to illustrate the capabilities of these methods to detect simulated check valve degradation. 3 refs., 22 figs., 4 tabs

Inter-enterprise system and application integration: a reality check

NARCIS (Netherlands)

Cardoso, J.; Aalst, van der W.M.P.; Bussler, C.; Sheth, A.P.; Sandkuhl, K.; Filipe, J.; Cordeiro, J.; Cardoso, J.

2008-01-01

This paper structures the summary of the panel held at the 9th International Conference on Enterprise Information Systems, Funchal, Madeira, 12-16 June 2007 that addressed the following question: "Are you still working on Inter-Enterprise System and Application Integration?" The panel aggregated

Workload analyse of assembling process

Science.gov (United States)

Ghenghea, L. D.

2015-11-01

The workload is the most important indicator for managers responsible of industrial technological processes no matter if these are automated, mechanized or simply manual in each case, machines or workers will be in the focus of workload measurements. The paper deals with workload analyses made to a most part manual assembling technology for roller bearings assembling process, executed in a big company, with integrated bearings manufacturing processes. In this analyses the delay sample technique have been used to identify and divide all bearing assemblers activities, to get information about time parts from 480 minutes day work time that workers allow to each activity. The developed study shows some ways to increase the process productivity without supplementary investments and also indicated the process automation could be the solution to gain maximum productivity.

Check valve diagnostics utilizing acoustic and magnetic technologies

International Nuclear Information System (INIS)

Agostinelli, A.

1991-01-01

The potential hazards associated with check valve failures make it necessary to detect check valve problems before they cause significant damage. In the nuclear industry, check valve failures are known to have resulted in damaging water hammer conditions, overpressurization of low pressure systems, steam binding of auxiliary feedwater pumps, and other serious component damage in power plant environments. Similar problems exist in fossil power and various process industries, but the resources dedicated to valve maintenance issues are greatly reduced. However, the trend toward plant life extension, predictive maintenance, and maximum operating efficiency will raise the general awareness of check valve maintenance in commercial (non-nuclear) applications. Although this paper includes specific references to the nuclear industry, the check valve problem conditions and diagnostic techniques apply across all power and process plant environments. The ability to accurately diagnose check valve conditions using non-intrusive, predictive maintenance testing methods allows for a more cost-efficient, productive maintenance program. One particular diagnostic system, called Quickcheck trademark, assists utilities in addressing these concerns. This article presents actual field test data and analysis that demonstrate the power of check valve diagnostics. Prior to presenting the field data, a brief overview of the system is overviewed

THE INFLUENCE OF CHECK DAMS ON FLUVIAL PROCESSES AND RIPARIAN VEGETATION IN MOUNTAIN REACHES OF TORRENTS

Directory of Open Access Journals (Sweden)

Giuseppe Bombino

2010-09-01

Full Text Available The complex hydrogeomorphological processes within the active channel of rivers strongly influence riparian vegetation development and organization, particularly in mountain streams where such processes can be remarkably impacted by engineering control works. In four mountain reaches of Calabrian fiumaras we analyze, through previously arranged methods (integrated by a multivariate statistic analysis, the relationships among hydrogeomorphological river characteristics and structure and the development of riparian vegetation within the active channel in transects located in proximity of check dams and in less disturbed sites. The results of this study demonstrate clear and relevant contrasts, due to the presence of check dams, in the physical and vegetation properties of upstream, downstream and intermediate sites around check dams. The multivariate statistical approach through the Principal Component Analysis (PCA highlighted evident relationships in all transects between groups of physical and vegetation properties. The regression analysis performed between the vegetation properties and the width:depth ratio or the specific discharge showed very different relationships between groups of transects, due to evident changes in channel morphology and in flow regime locally induced by check dams. Overall we have shown that check dams have far reaching effects in the extent and development of riparian vegetation of mountain torrent reaches, which extend far beyond physical adjustments to changed morphological, hydraulic and sedimentary conditions.

Automation of Geometry Input for Building Code Compliance Check

DEFF Research Database (Denmark)

Petrova, Ekaterina Aleksandrova; Johansen, Peter Lind; Jensen, Rasmus Lund

2017-01-01

Documentation of compliance with the energy performance regulations at the end of the detailed design phase is mandatory for building owners in Denmark. Therefore, besides multidisciplinary input, the building design process requires various iterative analyses, so that the optimal solutions can....... That has left the industry in constant pursuit of possibilities for integration of the tool within the Building Information Modelling environment so that the potential provided by the latter can be harvested and the processed can be optimized. This paper presents a solution for automated data extraction...... from building geometry created in Autodesk Revit and its translation to input for compliance check analysis....

Integrative self-assembly of functional hybrid nanoconstructs by inorganic wrapping of single biomolecules, biomolecule arrays and organic supramolecular assemblies.

Science.gov (United States)

Patil, Avinash J; Li, Mei; Mann, Stephen

2013-08-21

Synthesis of functional hybrid nanoscale objects has been a core focus of the rapidly progressing field of nanomaterials science. In particular, there has been significant interest in the integration of evolutionally optimized biological systems such as proteins, DNA, virus particles and cells with functional inorganic building blocks to construct mesoscopic architectures and nanostructured materials. However, in many cases the fragile nature of the biomolecules seriously constrains their potential applications. As a consequence, there is an on-going quest for the development of novel strategies to modulate the thermal and chemical stabilities, and performance of biomolecules under adverse conditions. This feature article highlights new methods of "inorganic molecular wrapping" of single or multiple protein molecules, individual double-stranded DNA helices, lipid bilayer vesicles and self-assembled organic dye superstructures using inorganic building blocks to produce bio-inorganic nanoconstructs with core-shell type structures. We show that spatial isolation of the functional biological nanostructures as "armour-plated" enzyme molecules or polynucleotide strands not only maintains their intact structure and biochemical properties, but also enables the fabrication of novel hybrid nanomaterials for potential applications in diverse areas of bionanotechnology.

Integrative self-assembly of functional hybrid nanoconstructs by inorganic wrapping of single biomolecules, biomolecule arrays and organic supramolecular assemblies

Science.gov (United States)

Patil, Avinash J.; Li, Mei; Mann, Stephen

2013-07-01

Synthesis of functional hybrid nanoscale objects has been a core focus of the rapidly progressing field of nanomaterials science. In particular, there has been significant interest in the integration of evolutionally optimized biological systems such as proteins, DNA, virus particles and cells with functional inorganic building blocks to construct mesoscopic architectures and nanostructured materials. However, in many cases the fragile nature of the biomolecules seriously constrains their potential applications. As a consequence, there is an on-going quest for the development of novel strategies to modulate the thermal and chemical stabilities, and performance of biomolecules under adverse conditions. This feature article highlights new methods of ``inorganic molecular wrapping'' of single or multiple protein molecules, individual double-stranded DNA helices, lipid bilayer vesicles and self-assembled organic dye superstructures using inorganic building blocks to produce bio-inorganic nanoconstructs with core-shell type structures. We show that spatial isolation of the functional biological nanostructures as ``armour-plated'' enzyme molecules or polynucleotide strands not only maintains their intact structure and biochemical properties, but also enables the fabrication of novel hybrid nanomaterials for potential applications in diverse areas of bionanotechnology.

Statistical Model Checking of Rich Models and Properties

DEFF Research Database (Denmark)

Poulsen, Danny Bøgsted

in undecidability issues for the traditional model checking approaches. Statistical model checking has proven itself a valuable supplement to model checking and this thesis is concerned with extending this software validation technique to stochastic hybrid systems. The thesis consists of two parts: the first part...... motivates why existing model checking technology should be supplemented by new techniques. It also contains a brief introduction to probability theory and concepts covered by the six papers making up the second part. The first two papers are concerned with developing online monitoring techniques...... systems. The fifth paper shows how stochastic hybrid automata are useful for modelling biological systems and the final paper is concerned with showing how statistical model checking is efficiently distributed. In parallel with developing the theory contained in the papers, a substantial part of this work...

Investigation of properties of novel silicon pixel assemblies employing thin n-in-p sensors and 3D-integration

International Nuclear Information System (INIS)

Weigell, Philipp

2013-01-01

Until the end of the 2020 decade the LHC programme will be defining the high energy frontier of particle physics. During this time, three upgrade steps of the accelerator are currently planned to further increase the luminosity and energy reach. In the course of these upgrades the specifications of several parts of the current LHC detectors will be exceeded. Especially, the innermost tracking detectors are challenged by the increasing track densities and the radiation damage. This thesis focuses on the implications for the ATLAS experiment. Here, around 2021/2, after having collected an integrated luminosity of around 300 fb -1 , the silicon and gas detector components of the inner tracker will reach the end of their lifetime and will need to be replaced to ensure sufficient performance for continued running - especially if the luminosity is raised to about 5 x 10 35 cm -2 s -1 as currently planned. An all silicon inner detector is foreseen to be installed. This upgrade demands cost effective pixel assemblies with a minimal material budget, a larger active area fraction as compared to the current detectors, and a higher granularity. Furthermore, the assemblies must be able to withstand received fluences up to 2 . 10 16 n eq /cm 2 . A new pixel assembly concept answering the challenges posed by the high instantaneous luminosities is investigated in this thesis. It employs five novel technologies, namely n-in-p pixel sensors, thin pixel sensors, slim edges with or without implanted sensor sides, and 3D-integration incorporating a new interconnection technology, named Solid Liquid InterDiffusion (SLID) as well as Inter-Chip-Vias (ICVs). n-in-p sensors are cost-effective, since they only need patterned processing on one side. Their performance before and after irradiation is investigated and compared to results obtained with currently used n-in-n sensors. Reducing the thickness of the sensors lowers the amount of multiple scattering within the tracking system and leads

Investigation of properties of novel silicon pixel assemblies employing thin n-in-p sensors and 3D-integration

Energy Technology Data Exchange (ETDEWEB)

Weigell, Philipp

2013-01-15

Until the end of the 2020 decade the LHC programme will be defining the high energy frontier of particle physics. During this time, three upgrade steps of the accelerator are currently planned to further increase the luminosity and energy reach. In the course of these upgrades the specifications of several parts of the current LHC detectors will be exceeded. Especially, the innermost tracking detectors are challenged by the increasing track densities and the radiation damage. This thesis focuses on the implications for the ATLAS experiment. Here, around 2021/2, after having collected an integrated luminosity of around 300 fb{sup -1}, the silicon and gas detector components of the inner tracker will reach the end of their lifetime and will need to be replaced to ensure sufficient performance for continued running - especially if the luminosity is raised to about 5 x 10{sup 35} cm{sup -2}s{sup -1} as currently planned. An all silicon inner detector is foreseen to be installed. This upgrade demands cost effective pixel assemblies with a minimal material budget, a larger active area fraction as compared to the current detectors, and a higher granularity. Furthermore, the assemblies must be able to withstand received fluences up to 2 . 10{sup 16} n{sub eq}/cm{sup 2}. A new pixel assembly concept answering the challenges posed by the high instantaneous luminosities is investigated in this thesis. It employs five novel technologies, namely n-in-p pixel sensors, thin pixel sensors, slim edges with or without implanted sensor sides, and 3D-integration incorporating a new interconnection technology, named Solid Liquid InterDiffusion (SLID) as well as Inter-Chip-Vias (ICVs). n-in-p sensors are cost-effective, since they only need patterned processing on one side. Their performance before and after irradiation is investigated and compared to results obtained with currently used n-in-n sensors. Reducing the thickness of the sensors lowers the amount of multiple scattering

Virtualization for Cost-Effective Teaching of Assembly Language Programming

Science.gov (United States)

Cadenas, José O.; Sherratt, R. Simon; Howlett, Des; Guy, Chris G.; Lundqvist, Karsten O.

2015-01-01

This paper describes a virtual system that emulates an ARM-based processor machine, created to replace a traditional hardware-based system for teaching assembly language. The virtual system proposed here integrates, in a single environment, all the development tools necessary to deliver introductory or advanced courses on modern assembly language…

UTP and Temporal Logic Model Checking

Science.gov (United States)

Anderson, Hugh; Ciobanu, Gabriel; Freitas, Leo

In this paper we give an additional perspective to the formal verification of programs through temporal logic model checking, which uses Hoare and He Unifying Theories of Programming (UTP). Our perspective emphasizes the use of UTP designs, an alphabetised relational calculus expressed as a pre/post condition pair of relations, to verify state or temporal assertions about programs. The temporal model checking relation is derived from a satisfaction relation between the model and its properties. The contribution of this paper is that it shows a UTP perspective to temporal logic model checking. The approach includes the notion of efficiency found in traditional model checkers, which reduced a state explosion problem through the use of efficient data structures

Coverage Metrics for Model Checking

Science.gov (United States)

Penix, John; Visser, Willem; Norvig, Peter (Technical Monitor)

2001-01-01

When using model checking to verify programs in practice, it is not usually possible to achieve complete coverage of the system. In this position paper we describe ongoing research within the Automated Software Engineering group at NASA Ames on the use of test coverage metrics to measure partial coverage and provide heuristic guidance for program model checking. We are specifically interested in applying and developing coverage metrics for concurrent programs that might be used to support certification of next generation avionics software.

First experiences with the LHC BLM sanity checks

Science.gov (United States)

Emery, J.; Dehning, B.; Effinger, E.; Nordt, A.; Sapinski, M. G.; Zamantzas, C.

2010-12-01

The reliability concerns have driven the design of the Large Hardron Collider (LHC) Beam Loss Monitoring (BLM) system from the early stage of the studies up to the present commissioning and the latest development of diagnostic tools. To protect the system against non-conformities, new ways of automatic checking have been developed and implemented. These checks are regularly and systematically executed by the LHC operation team to ensure that the system status is after each test "as good as new". The sanity checks are part of this strategy. They are testing the electrical part of the detectors (ionisation chamber or secondary emission detector), their cable connections to the front-end electronics, further connections to the back-end electronics and their ability to request a beam abort. During the installation and in the early commissioning phase, these checks have shown their ability to find also non-conformities caused by unexpected failure event scenarios. In every day operation, a non-conformity discovered by this check inhibits any further injections into the LHC until the check confirms the absence of non-conformities.

First experiences with the LHC BLM sanity checks

International Nuclear Information System (INIS)

Emery, J; Dehning, B; Effinger, E; Nordt, A; Sapinski, M G; Zamantzas, C

2010-01-01

The reliability concerns have driven the design of the Large Hardron Collider (LHC) Beam Loss Monitoring (BLM) system from the early stage of the studies up to the present commissioning and the latest development of diagnostic tools. To protect the system against non-conformities, new ways of automatic checking have been developed and implemented. These checks are regularly and systematically executed by the LHC operation team to ensure that the system status is after each test a s good as new . The sanity checks are part of this strategy. They are testing the electrical part of the detectors (ionisation chamber or secondary emission detector), their cable connections to the front-end electronics, further connections to the back-end electronics and their ability to request a beam abort. During the installation and in the early commissioning phase, these checks have shown their ability to find also non-conformities caused by unexpected failure event scenarios. In every day operation, a non-conformity discovered by this check inhibits any further injections into the LHC until the check confirms the absence of non-conformities.

First experiences with the LHC BLM sanity checks

Energy Technology Data Exchange (ETDEWEB)

Emery, J; Dehning, B; Effinger, E; Nordt, A; Sapinski, M G; Zamantzas, C, E-mail: Jonathan.emery@cern.ch [CERN, CH-1211 Geneve 23 (Switzerland)

2010-12-15

The reliability concerns have driven the design of the Large Hardron Collider (LHC) Beam Loss Monitoring (BLM) system from the early stage of the studies up to the present commissioning and the latest development of diagnostic tools. To protect the system against non-conformities, new ways of automatic checking have been developed and implemented. These checks are regularly and systematically executed by the LHC operation team to ensure that the system status is after each test {sup a}s good as new{sup .} The sanity checks are part of this strategy. They are testing the electrical part of the detectors (ionisation chamber or secondary emission detector), their cable connections to the front-end electronics, further connections to the back-end electronics and their ability to request a beam abort. During the installation and in the early commissioning phase, these checks have shown their ability to find also non-conformities caused by unexpected failure event scenarios. In every day operation, a non-conformity discovered by this check inhibits any further injections into the LHC until the check confirms the absence of non-conformities.

Do alcohol compliance checks decrease underage sales at neighboring establishments?

Science.gov (United States)

Erickson, Darin J; Smolenski, Derek J; Toomey, Traci L; Carlin, Bradley P; Wagenaar, Alexander C

2013-11-01

Underage alcohol compliance checks conducted by law enforcement agencies can reduce the likelihood of illegal alcohol sales at checked alcohol establishments, and theory suggests that an alcohol establishment that is checked may warn nearby establishments that compliance checks are being conducted in the area. In this study, we examined whether the effects of compliance checks diffuse to neighboring establishments. We used data from the Complying with the Minimum Drinking Age trial, which included more than 2,000 compliance checks conducted at more than 900 alcohol establishments. The primary outcome was the sale of alcohol to a pseudo-underage buyer without the need for age identification. A multilevel logistic regression was used to model the effect of a compliance check at each establishment as well as the effect of compliance checks at neighboring establishments within 500 m (stratified into four equal-radius concentric rings), after buyer, license, establishment, and community-level variables were controlled for. We observed a decrease in the likelihood of establishments selling alcohol to underage youth after they had been checked by law enforcement, but these effects quickly decayed over time. Establishments that had a close neighbor (within 125 m) checked in the past 90 days were also less likely to sell alcohol to young-appearing buyers. The spatial effect of compliance checks on other establishments decayed rapidly with increasing distance. Results confirm the hypothesis that the effects of police compliance checks do spill over to neighboring establishments. These findings have implications for the development of an optimal schedule of police compliance checks.

Integrated Quality Control of Precision Assemblies using Computed Tomography

DEFF Research Database (Denmark)

Stolfi, Alessandro

coor-dinate measuring machines (CMMs) when working with complex and fragile parts. This Ph.D. project at DTU Mechanical Engineering concerns the applicability of CT for quality control of precision assem-blies. Investigations to quantify the accuracy of CT measurements, reference artefacts to correct...

Three-Dimensional Self-Assembled Photonic Crystal Waveguide

Science.gov (United States)

Baek, Kang-Hyun

Photonic crystals (PCs), two- or three-dimensionally periodic, artificial, and dielectric structures, have a specific forbidden band for electromagnetic waves, referred to as photonic bandgap (PBG). The PBG is analogous to the electronic bandgap in natural crystal structures with periodic atomic arrangement. A well-defined and embedded planar, line, or point defect within the PCs causes a break in its structural periodicity, and introduces a state in the PBG for light localization. It offers various applications in integrated optics and photonics including optical filters, sharp bending light guides and very low threshold lasers. Using nanofabrication processes, PCs of the 2-D slab-type and 3-D layer-by-layer structures have been investigated widely. Alternatively, simple and low-cost self-assembled PCs with full 3-D PBG, inverse opals, have been suggested. A template with face centered cubic closed packed structure, opal, may initially be built by self-assembly of colloidal spheres, and is selectively removed after infiltrating high refractive index materials into the interstitials of spheres. In this dissertation, the optical waveguides utilizing the 3-D self-assembled PCs are discussed. The waveguides were fabricated by microfabrication technology. For high-quality colloidal silica spheres and PCs, reliable synthesis, self-assembly, and characterization techniques were developed. Its theoretical and experimental demonstrations are provided and correlated. They suggest that the self-assembled PCs with PBG are feasible for the applications in integrated optics and photonics.

Optimal production planning for PCB assembly

CERN Document Server

Ho, William

2006-01-01

Focuses on the optimization of the Printed circuit board (PCB) assembly lines' efficiency. This book integrates the component sequencing and the feeder arrangement problems together for the pick-and-place machine and the chip shooter machines.

SoS contract verification using statistical model checking

Directory of Open Access Journals (Sweden)

Alessandro Mignogna

2013-11-01

Full Text Available Exhaustive formal verification for systems of systems (SoS is impractical and cannot be applied on a large scale. In this paper we propose to use statistical model checking for efficient verification of SoS. We address three relevant aspects for systems of systems: 1 the model of the SoS, which includes stochastic aspects; 2 the formalization of the SoS requirements in the form of contracts; 3 the tool-chain to support statistical model checking for SoS. We adapt the SMC technique for application to heterogeneous SoS. We extend the UPDM/SysML specification language to express the SoS requirements that the implemented strategies over the SoS must satisfy. The requirements are specified with a new contract language specifically designed for SoS, targeting a high-level English- pattern language, but relying on an accurate semantics given by the standard temporal logics. The contracts are verified against the UPDM/SysML specification using the Statistical Model Checker (SMC PLASMA combined with the simulation engine DESYRE, which integrates heterogeneous behavioral models through the functional mock-up interface (FMI standard. The tool-chain allows computing an estimation of the satisfiability of the contracts by the SoS. The results help the system architect to trade-off different solutions to guide the evolution of the SoS.

Automated Array Assembly, Phase 2. Quarterly technical progress report, April-June 1979

Energy Technology Data Exchange (ETDEWEB)

Carbajal, B.G.

1979-07-01

The Automated Array Assembly Task, Phase 2 of the Low Cost Solar Array (LSA) Project is a process development task. This contract provides for the fabrication of modules from large area Tandem Junction Cells (TJC). The key activities in this contract effort are (a) Large Area TJC including cell design, process verification and cell fabrication and (b) Tandem Junction Module (TJM) including definition of the cell-module interfaces, substrate fabrication, interconnect fabrication and module assembly. The overall goal is to advance solar cell module process technology to meet the 1986 goal of a production capability of 500 megawatts per year at a cost of less than $500 per peak kilowatt. This contract will focus on the Tandem Junction Module process. During this quarter, effort was focused on design and process verification. The large area TJC design was completed and the design verification was completed. Process variation experiments led to refinements in the baseline TJC process. Formed steel substrates were porcelainized. Cell array assembly techniques using infrared soldering are being checked out. Dummy cell arrays up to 5 cell by 5 cell have been assembled using all backside contacts.

Muscle assembly: a titanic achievement?

Science.gov (United States)

Gregorio, C C; Granzier, H; Sorimachi, H; Labeit, S

1999-02-01

The formation of perfectly aligned myofibrils in striated muscle represents a dramatic example of supramolecular assembly in eukaryotic cells. Recently, considerable progress has been made in deciphering the roles that titin, the third most abundant protein in muscle, has in this process. An increasing number of sarcomeric proteins (ligands) are being identified that bind to specific titin domains. Titin may serve as a molecular blueprint for sarcomere assembly and turnover by specifying the precise position of its ligands within each half-sarcomere in addition to functioning as a molecular spring that maintains the structural integrity of the contracting myofibrils.

Nuclear fuel: modelling the advanced plutonium assembly

International Nuclear Information System (INIS)

Kaoua, Th.; Lenain, R.

2004-01-01

The benefits of modeling in the nuclear sector are illustrated by the example of the design study for a new plutonium fuel assembly, APA, capable of ensuring maximum consumption of this fuel in pressurized-water reactors. Beyond the physical design of the assembly and its integration into the reactor, this serves for the working out of a complete materials flow and assists in modeling production from the entire inventory of nuclear power stations. (authors)

Nuclear fuel: modelling the advanced plutonium assembly

International Nuclear Information System (INIS)

N'kaoua, Th.; Lenain, R.

2002-01-01

The benefits of modeling in the nuclear sector are illustrated by the example of the design study for a new plutonium fuel assembly, APA, capable of ensuring maximum consumption of this fuel in pressurized-water reactors. Beyond the physical design of the assembly and its integration into the reactor, this serves for the working out of a complete materials flow and assists in modeling production from the entire inventory of nuclear power stations. (authors)

Checking and Balancing: Banking and Budgeting.

Science.gov (United States)

Thypin, Marilyn; Glasner, Lynne

A short fictional work for limited English speakers is presented that relates a young couple's experience in learning about managing their money more carefully by budgeting and maintaining a checking account. Since the couple did not have a checking account, they had to go to their savings bank in order to pay each bill and they had to keep cash…

Glovebox pressure relief and check valve

Energy Technology Data Exchange (ETDEWEB)

Blaedel, K.L.

1986-03-17

This device is a combined pressure relief valve and check valve providing overpressure protection and preventing back flow into an inert atmosphere enclosure. The pressure relief is embodied by a submerged vent line in a mercury reservior, the releif pressure being a function of the submerged depth. The pressure relief can be vented into an exhaust system and the relieving pressure is only slightly influenced by the varying pressure in the exhaust system. The check valve is embodied by a ball which floats on the mercury column and contacts a seat whenever vacuum exists within the glovebox enclosure. Alternatively, the check valve is embodied by a vertical column of mercury, the maximum back pressure being a function of the height of the column of mercury.

Glovebox pressure relief and check valve

International Nuclear Information System (INIS)

Blaedel, K.L.

1986-01-01

This device is a combined pressure relief valve and check valve providing overpressure protection and preventing back flow into an inert atmosphere enclosure. The pressure relief is embodied by a submerged vent line in a mercury reservior, the releif pressure being a function of the submerged depth. The pressure relief can be vented into an exhaust system and the relieving pressure is only slightly influenced by the varying pressure in the exhaust system. The check valve is embodied by a ball which floats on the mercury column and contacts a seat whenever vacuum exists within the glovebox enclosure. Alternatively, the check valve is embodied by a vertical column of mercury, the maximum back pressure being a function of the height of the column of mercury

Thermal battery automated assembly station conceptual design

Energy Technology Data Exchange (ETDEWEB)

Jacobs, D

1988-08-01

Thermal battery assembly involves many operations which are labor- intense. In August 1986, a project team was formed at GE Neutron Devices to investigate and evaluate more efficient and productive battery assembly techniques through the use of automation. The result of this study was the acceptance of a plan to automate the piece part pellet fabrication and battery stacking operations by using computerized pellet presses and robots which would be integrated by a main computer. This report details the conceptual design and development plan to be followed in the fabrication, development, and implementation of a thermal battery automated assembly station. 4 figs., 8 tabs.

Repeated checking induces uncertainty about future threat

NARCIS (Netherlands)

Giele, C.L.|info:eu-repo/dai/nl/318754460; Engelhard, I.M.|info:eu-repo/dai/nl/239681533; van den Hout, M.A.|info:eu-repo/dai/nl/070445354; Dek, E.C.P.|info:eu-repo/dai/nl/313959552; Damstra, Marianne; Douma, Ellen

2015-01-01

Studies have shown that obsessive-compulsive (OC) -like repeated checking paradoxically increases memory uncertainty. This study tested if checking also induces uncertainty about future threat by impairing the distinction between danger and safety cues. Participants (n = 54) engaged in a simulated

A classification scheme for LWR fuel assemblies

Energy Technology Data Exchange (ETDEWEB)

Moore, R.S.; Williamson, D.A.; Notz, K.J.

1988-11-01

With over 100 light water nuclear reactors operating nationwide, representing designs by four primary vendors, and with reload fuel manufactured by these vendors and additional suppliers, a wide variety of fuel assembly types are in existence. At Oak Ridge National Laboratory, both the Systems Integration Program and the Characteristics Data Base project required a classification scheme for these fuels. This scheme can be applied to other areas and is expected to be of value to many Office of Civilian Radioactive Waste Management programs. To develop the classification scheme, extensive information on the fuel assemblies that have been and are being manufactured by the various nuclear fuel vendors was compiled, reviewed, and evaluated. It was determined that it is possible to characterize assemblies in a systematic manner, using a combination of physical factors. A two-stage scheme was developed consisting of 79 assembly types, which are grouped into 22 assembly classes. The assembly classes are determined by the general design of the reactor cores in which the assemblies are, or were, used. The general BWR and PWR classes are divided differently but both are based on reactor core configuration. 2 refs., 15 tabs.

A classification scheme for LWR fuel assemblies

International Nuclear Information System (INIS)

Moore, R.S.; Williamson, D.A.; Notz, K.J.

1988-11-01

With over 100 light water nuclear reactors operating nationwide, representing designs by four primary vendors, and with reload fuel manufactured by these vendors and additional suppliers, a wide variety of fuel assembly types are in existence. At Oak Ridge National Laboratory, both the Systems Integration Program and the Characteristics Data Base project required a classification scheme for these fuels. This scheme can be applied to other areas and is expected to be of value to many Office of Civilian Radioactive Waste Management programs. To develop the classification scheme, extensive information on the fuel assemblies that have been and are being manufactured by the various nuclear fuel vendors was compiled, reviewed, and evaluated. It was determined that it is possible to characterize assemblies in a systematic manner, using a combination of physical factors. A two-stage scheme was developed consisting of 79 assembly types, which are grouped into 22 assembly classes. The assembly classes are determined by the general design of the reactor cores in which the assemblies are, or were, used. The general BWR and PWR classes are divided differently but both are based on reactor core configuration. 2 refs., 15 tabs

Fuel assembly

International Nuclear Information System (INIS)

Nomata, Terumitsu.

1993-01-01

Among fuel pellets to be loaded to fuel cans of a fuel assembly, fuel pellets having a small thermal power are charged in a region from the end of each of spacers up to about 50mm on the upstream of coolants that flow vertically at the periphery of fuel rods. Coolants at the periphery of fuel rods are heated by the heat generation, to result in voids. However, since cooling effect on the upstream of the spacers is low due to influences of the spacers. Further, since the fuel pellets disposed in the upstream region have small thermal power, a void coefficient is not increased. Even if a thermal power exceeding cooling performance should be generated, there is no worry of causing burnout in the upstream region. Even if burnout should be caused, safety margin and reliability relative to burnout are improved, to increase an allowable thermal power, thereby enabling to improve integrity and reliability of fuel rods and fuel assemblies. (N.H.)

Inkjet 3D printed check microvalve

International Nuclear Information System (INIS)

Walczak, Rafał; Adamski, Krzysztof; Lizanets, Danylo

2017-01-01

3D printing enables fast and relatively easy fabrication of various microfluidic structures including microvalves. A check microvalve is the simplest valve enabling control of the fluid flow in microchannels. Proper operation of the check valve is ensured by a movable element that tightens the valve seat during backward flow and enables free flow for forward pressure. Thus, knowledge of the mechanical properties of the movable element is crucial for optimal design and operation of the valve. In this paper, we present for the first time the results of investigations on basic mechanical properties of the building material used in multijet 3D printing. Specified mechanical properties were used in the design and fabrication of two types of check microvalve—with deflecting or hinge-fixed microflap—with 200 µ m and 300 µ m thickness. Results of numerical simulation and experimental data of the microflap deflection were obtained and compared. The valves were successfully 3D printed and characterised. Opening/closing characteristics of the microvalve for forward and backward pressures were determined. Thus, proper operation of the check microvalve so developed was confirmed. (technical note)

Dynamics of assembly production flow

Science.gov (United States)

Ezaki, Takahiro; Yanagisawa, Daichi; Nishinari, Katsuhiro

2015-06-01

Despite recent developments in management theory, maintaining a manufacturing schedule remains difficult because of production delays and fluctuations in demand and supply of materials. The response of manufacturing systems to such disruptions to dynamic behavior has been rarely studied. To capture these responses, we investigate a process that models the assembly of parts into end products. The complete assembly process is represented by a directed tree, where the smallest parts are injected at leaves and the end products are removed at the root. A discrete assembly process, represented by a node on the network, integrates parts, which are then sent to the next downstream node as a single part. The model exhibits some intriguing phenomena, including overstock cascade, phase transition in terms of demand and supply fluctuations, nonmonotonic distribution of stockout in the network, and the formation of a stockout path and stockout chains. Surprisingly, these rich phenomena result from only the nature of distributed assembly processes. From a physical perspective, these phenomena provide insight into delay dynamics and inventory distributions in large-scale manufacturing systems.

Thermal Aspects Related to Power Assemblies

Directory of Open Access Journals (Sweden)

PLESCA, A.

2010-02-01

Full Text Available In many cases when a power assembly based on power semiconductors is used, catastrophic failure is the result of steep temperature gradient in the localized temperature distribution. Hence, an optimal heatsink design for certain industrial applications has become a real necessity. In this paper, the Pro/ENGINEER software with the thermal simulation integrated tool, Pro/MECHANICA, has been used for thermal study of a specific power semiconductor assembly. A series of steady-state and transient thermal simulations have been performed. The experimental tests have confirmed the simulation results. Therefore, the use of specific 3D modeling and simulation software allows to design special power semiconductor assemblies with a better thermal transfer between its heatsink and power electronic components at given operating conditions.

A general design strategy for block copolymer directed self-assembly patterning of integrated circuits contact holes using an alphabet approach.

Science.gov (United States)

Yi, He; Bao, Xin-Yu; Tiberio, Richard; Wong, H-S Philip

2015-02-11

Directed self-assembly (DSA) is a promising lithography candidate for technology nodes beyond 14 nm. Researchers have shown contact hole patterning for random logic circuits using DSA with small physical templates. This paper introduces an alphabet approach that uses a minimal set of small physical templates to pattern all contacts configurations on integrated circuits. We illustrate, through experiments, a general and scalable template design strategy that links the DSA material properties to the technology node requirements.

Surface Assembly of the End Cap Muon Spectrometer

CERN Multimedia

S. Palestini

Before the final installation in the ATLAS detector, the chambers of the inner and middle forward stations of the Muon spectrometer are integrated and assembled on large support structures. Work on the sectors of the Thin Gap Chamber (TGC) Big Wheels (trigger chambers) and of the Muon Drift Tube (MDT) Big Wheels (precision tracking chambers) started early this year, and has recently expanded to all the foreseen working areas, covering most the surface of building 180. Several operations are performed, often in parallel, by different teams: final integration of the detectors, assembly of the support structures, installation and test of services, installation of chambers, and final tests. Control of the geometry is performed frequently both on assembly tooling and on complete sectors. The final tests verify the response of the detectors and of the electronics, including read-out and trigger electronics, the alignment system, and the detector control. The sectors are designed as a unit that can be fully commis...

A versatile passive and active non-destructive device for spent fuel assemblies monitoring

International Nuclear Information System (INIS)

Berne, R.; Bignan, G.; Andrieu, G.; Dethan, B.

1993-01-01

The monitoring of spent fuel assemblies in reactor pools or in reprocessing plants with NDA methods is interesting (non-destructivity, non-intrusivity) for process control, safety-criticality and/or nuclear material management. In this context, the authors present the results of the development and design of a prototype device (physical methods used, qualification...) called PYTHON. The aim of PYTHON is to check the declared characteristic values of an irradiated assembly before taking it into a transport cask for safety criticality control. The PYTHON device consists of a detector head in two sections and a 252 Cf source if active neutron counting is to be used. Each section of the detection head consists of two detectors: one fission chamber and one ionization chamber

Systematic Review of the Check-In, Check-Out Intervention for Students at Risk for Emotional and Behavioral Disorders

Science.gov (United States)

Hawken, Leanne S.; Bundock, Kaitlin; Kladis, Kristin; O'Keeffe, Breda; Barret, Courtenay A.

2014-01-01

The purpose of this systematic literature review was to summarize outcomes of the Check-in Check-out (CICO) intervention across elementary and secondary settings. Twenty-eight studies utilizing both single subject and group (experimental and quasi-experimental) designs were included in this review. Median effect sizes across the eight group…

Engineering of automated assembly of beam-shaping optics

Science.gov (United States)

Haag, Sebastian; Sinhoff, Volker; Müller, Tobias; Brecher, Christian

2014-03-01

Beam-shaping is essential for any kind of laser application. Assembly technologies for beam-shaping subassemblies are subject to intense research and development activities and their technical feasibility has been proven in recent years while economic viability requires more efficient engineering tools for process planning and production ramp up of complex assembly tasks for micro-optical systems. The work presented in this paper aims for significant reduction of process development and production ramp up times for the automated assembly of micro-optical subassemblies for beam-collimation and beam-tilting. The approach proposed bridges the gap between the product development phase and the realization of automation control through integration of established software tools such as optics simulation and CAD modeling as well as through introduction of novel software tools and methods to efficiently describe active alignment strategies. The focus of the paper is put on the methodological approach regarding the engineering of assembly processes for beam-shaping micro-optics and the formal representation of assembly objectives similar to representation in mechanical assemblies. Main topic of the paper is the engineering methodology for active alignment processes based on the classification of optical functions for beam-shaping optics and corresponding standardized measurement setups including adaptable alignment algorithms. The concepts are applied to industrial use-cases: (1) integrated collimation module for fast- and slow-axis and (2) beam-tilting subassembly consisting of a fast-axis collimator and micro-lens array. The paper concludes with an overview of current limitations as well as an outlook on the next development steps considering adhesive bonding processes.

Next-generation nozzle check valve significantly reduces operating costs

Energy Technology Data Exchange (ETDEWEB)

Roorda, O. [SMX International, Toronto, ON (Canada)

2009-01-15

Check valves perform an important function in preventing reverse flow and protecting plant and mechanical equipment. However, the variety of different types of valves and extreme differences in performance even within one type can change maintenance requirements and life cycle costs, amounting to millions of dollars over the typical 15-year design life of piping components. A next-generation non-slam nozzle check valve which prevents return flow has greatly reduced operating costs by protecting the mechanical equipment in a piping system. This article described the check valve varieties such as the swing check valve, a dual-plate check valve, and nozzle check valves. Advancements in optimized design of a non-slam nozzle check valve were also discussed, with particular reference to computer flow modelling such as computational fluid dynamics; computer stress modelling such as finite element analysis; and flow testing (using rapid prototype development and flow loop testing), both to improve dynamic performance and reduce hydraulic losses. The benefits of maximized dynamic performance and minimized pressure loss from the new designed valve were also outlined. It was concluded that this latest non-slam nozzle check valve design has potential applications in natural gas, liquefied natural gas, and oil pipelines, including subsea applications, as well as refineries, and petrochemical plants among others, and is suitable for horizontal and vertical installation. The result of this next-generation nozzle check valve design is not only superior performance, and effective protection of mechanical equipment but also minimized life cycle costs. 1 fig.

Principle and opening-closing character analysis of DC check valve

International Nuclear Information System (INIS)

Han Xu; Zhou Yu

2006-01-01

When the behaviour of main pump in PWR power plant change, as a result of arresting fluid countercurrent current by check valve, water hammer phenomena met occur more or less in loop. Serious water hammer not only met brought incident of over pressure, imperil pressure boundary, but also may engender check valve lapse. DC check valve is a kind of new theory check valve, is designed to avoid serious water hammer phenomena at tradition check valve closing, the analyses and experiment indicate that DC check valve can availably solve water hammer problem in the loop, and be able to reliably prevent fluid countercurrent. (authors)

Partial-order reduction for GPU model checking

NARCIS (Netherlands)

Neele, T.S.; Wijs, A.J.; Bošnački, D.; van de Pol, J.C.

2016-01-01

Model checking using GPUs has seen increased popularity over the last years. Because GPUs have a limited amount of memory, only small to medium-sized systems can be verified. For on-the-fly explicitstate model checking, we improve memory efficiency by applying partialorder reduction. We propose

40 CFR 89.317 - NOX converter check.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false NOX converter check. 89.317 Section 89.317 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED..., the chemiluminescent oxides of nitrogen analyzer shall be checked for NO2 to NO converter efficiency...

Assessment of check-dam groundwater recharge with water-balance calculations

Science.gov (United States)

Djuma, Hakan; Bruggeman, Adriana; Camera, Corrado; Eliades, Marinos

2017-04-01

Studies on the enhancement of groundwater recharge by check-dams in arid and semi-arid environments mainly focus on deriving water infiltration rates from the check-dam ponding areas. This is usually achieved by applying simple water balance models, more advanced models (e.g., two dimensional groundwater models) and field tests (e.g., infiltrometer test or soil pit tests). Recharge behind the check-dam can be affected by the built-up of sediment as a result of erosion in the upstream watershed area. This natural process can increase the uncertainty in the estimates of the recharged water volume, especially for water balance calculations. Few water balance field studies of individual check-dams have been presented in the literature and none of them presented associated uncertainties of their estimates. The objectives of this study are i) to assess the effect of a check-dam on groundwater recharge from an ephemeral river; and ii) to assess annual sedimentation at the check-dam during a 4-year period. The study was conducted on a check-dam in the semi-arid island of Cyprus. Field campaigns were carried out to measure water flow, water depth and check-dam topography in order to establish check-dam water height, volume, evaporation, outflow and recharge relations. Topographic surveys were repeated at the end of consecutive hydrological years to estimate the sediment built up in the reservoir area of the check dam. Also, sediment samples were collected from the check-dam reservoir area for bulk-density analyses. To quantify the groundwater recharge, a water balance model was applied at two locations: at the check-dam and corresponding reservoir area, and at a 4-km stretch of the river bed without check-dam. Results showed that a check-dam with a storage capacity of 25,000 m3 was able to recharge to the aquifer, in four years, a total of 12 million m3 out of the 42 million m3 of measured (or modelled) streamflow. Recharge from the analyzed 4-km long river section without

Design and Testing of the Fusion Virtual Assembly System FVAS1.0

International Nuclear Information System (INIS)

Pengcheng Long; Songlin Liu; Yican Wu

2006-01-01

Virtual assembly (VA), utilizing virtual reality (VR) technologies to plan and evaluate assembly process, retains the benefits (time-saving, inexpensive and no hazardous) of VR technologies and conquers the shortcoming of physical prototypes, such as long circle, high cost, low precision, and so on. Presented in this paper is the Fusion Virtual Assembly System FVAS 1.0 that makes possible engineering application for assemblies of large-scale complex nuclear facilities. FVAS 1.0 is designed to support the planning, evaluation and demonstration of assembly process, and training assemblers, and to work on PC (personal computer) platform. In this paper, architecture and main features of FVAS are introduced firstly. Then, design of the key sections (such as collision detection, virtual roaming) are described in detail. Finally, some successful application cases are presented. To enhance the real-time performance for large-scale nuclear facilities simulation, a policy based on separation of display scene and collision detection scene has been adopted. The display scene can be predigested to reduce the time of scene refreshment, and the collision detection performance is greatly improved by using the mature interference check ability of commercial CAD systems. Convenient observation mechanism brings more practicability. So a multi-viewpoints roaming scheme has been utilized to facilitate users' assembly operation. Users can obtain much optical information from multiple angles by switching between multi-viewpoints. The ESAT superconducting tokamak is characterized by large volume, complicated constitution and high assembly precision, e.g. the strict precision requirement in the assembly for the three tori (the tori of vacuum vessel, thermal shield, and toroidal coil). FVAS 1.0 has succeeded in demonstrating the assembly process of ESAT components. Furthermore, FVAS 1.0 has been applied to evaluate FDS-I (Fusion-Driven Sub-critical system) concept from assembly point of

Self-Assembly of Microscale Parts through Magnetic and Capillary Interactions

Directory of Open Access Journals (Sweden)

Madan Dubey

2011-03-01

Full Text Available Self-assembly is a promising technique to overcome fundamental limitations with integrating, packaging, and general handling of individual electronic-related components with characteristic lengths significantly smaller than 1 mm. Here we describe the use of magnetic and capillary forces to self-assemble 280 µm sized silicon building blocks into interconnected structures which approach a three-dimensional crystalline configuration. Integrated permanent magnet microstructures provided magnetic forces, while a low-melting-point solder alloy provided capillary forces. A finite element model of forces between the magnetic features demonstrated the utility of magnetic forces at this size scale. Despite a slight departure from designed dimensions in the actual fabricated parts, the combination of magnetic and capillary forces improved the assembly yield to 8%, over approximately 0.1% achieved previously with capillary forces alone.

AUTOMATED HOTEL CHECK-IN SERTA DAMPAKNYA PADA TENAGA KERJA LOKAL

Directory of Open Access Journals (Sweden)

Ni Gusti Nyoman Suci Murni

2017-10-01

Full Text Available The tourism sector is one of the most heavily influenced sectors of information technology. Hotels that are a component of tourism cannot be separated from these influences, especially in information services, room reservations, check-in / check-out service, and other services. With the sophistication of information technology, everyone can access any information, from anywhere; at a very cheap price even every country provides free facilities for that purpose. This study uses qualitative methods where the data source obtained by looking for some libraries related to self check-in. The results show that there are some differences that applied between the check-in manual and self check-in, and the impact caused by the application of self check-in. The positive impact of self check-in are speeding up the check-in process, saving payrolls, simplifying services, simplifying reporting, and saving time. While the negative impacts such as reducing employment in developing countries, reducing social communication / human touch, reducing the understanding of cross cultural understanding, allowing the occurrence of crime (cyber crime as well as very expensive initial cost.

Integrated Testing of a Carbon Dioxide Removal Assembly and a Temperature-Swing Adsorption Compressor for Closed-Loop Air Revitalization

Science.gov (United States)

Knox, J. C.; Mulloth, Lila; Frederick, Kenneth; Affleck, Dave

2003-01-01

Accumulation and subsequent compression of carbon dioxide that is removed from space cabin are two important processes involved in a closed-loop air revitalization scheme of the International Space Station (ISS). The carbon dioxide removal assembly (CDRA) of ISS currently operates in an open loop mode without a compressor. This paper describes the integrated test results of a flight-like CDRA and a temperature-swing adsorption compressor (TSAC) for carbon dioxide removal and compression. The paper provides details of the TSAC operation at various CO2 loadings and corresponding performance of CDRA.

SPEED ROLLER STAND MEASUREMENT SYSTEM CHECKING TECHNIQUE

Directory of Open Access Journals (Sweden)

Y. Zybtsev

2011-01-01

Full Text Available The study has shown that the accuracy of brakes checking by inertial stands depends upon the applied methods of measurement of braking parameters (stand slowing down, braking distance, brakes triggering time, current speed as well as the methods of metrological checking of measuring system canals.

Partial-Order Reduction for GPU Model Checking

NARCIS (Netherlands)

Neele, T.; Wijs, A.; Bosnacki, D.; van de Pol, Jan Cornelis; Artho, C; Legay, A.; Peled, D.

2016-01-01

Model checking using GPUs has seen increased popularity over the last years. Because GPUs have a limited amount of memory, only small to medium-sized systems can be verified. For on-the-fly explicit-state model checking, we improve memory efficiency by applying partial-order reduction. We propose

Check Verbraucherpolitik und Verbraucherbeteiligung

DEFF Research Database (Denmark)

Hagen, Kornelia; Micklitz, Hans-W.; Oehler, Andreas

2013-01-01

The paper discusses the opportunities for an empirically grounded decision support system as an instrument for independent and scientifically based consumer policy consulting. To date, consumer policy is dominated by the information paradigm and the leitbild of the rational, sovereign...... and information-seeking consumer. Yet, both everyday practice and research in behavioural economics show that this view lacks empirical ground. In fact, there are different consumer types and different forms of rationalities at work. Effective consumer policy making should be based on the empirically revealed...... an empirically based “Check Consumer Policy and Consumer Participation” as a systematic decision and evaluation tool for policy makers. This check should be independent from the government and should be grounded on an empirical view of the consumer. Consumer policy tools should be tested with real consumers...

An Integrated Picture of Star Formation, Metallicity Evolution, and Galactic Stellar Mass Assembly

Science.gov (United States)

Cowie, L. L.; Barger, A. J.

2008-10-01

We present an integrated study of star formation and galactic stellar mass assembly from z = 0.05 to 1.5 and galactic metallicity evolution from z = 0.05 to 0.9 using a very large and highly spectroscopically complete sample selected by rest-frame NIR bolometric flux in the GOODS-N. We assume a Salpeter IMF and fit Bruzual & Charlot models to compute the galactic stellar masses and extinctions. We determine the expected formed stellar mass density growth rates produced by star formation and compare them with the growth rates measured from the formed stellar mass functions by mass interval. We show that the growth rates match if the IMF is slightly increased from the Salpeter IMF at intermediate masses (~10 M⊙). We investigate the evolution of galaxy color, spectral type, and morphology with mass and redshift and the evolution of mass with environment. We find that applying extinction corrections is critical when analyzing galaxy colors; e.g., nearly all of the galaxies in the green valley are 24 μm sources, but after correcting for extinction, the bulk of the 24 μm sources lie in the blue cloud. We find an evolution of the metallicity-mass relation corresponding to a decrease of 0.21 +/- 0.03 dex between the local value and the value at z = 0.77 in the 1010-1011 M⊙ range. We use the metallicity evolution to estimate the gas mass of the galaxies, which we compare with the galactic stellar mass assembly and star formation histories. Overall, our measurements are consistent with a galaxy evolution process dominated by episodic bursts of star formation and where star formation in the most massive galaxies (gtrsim1011 M⊙) ceases at z Technology, the University of California, and NASA and was made possible by the generous financial support of the W. M. Keck Foundation.

Development of an Advanced Recycle Filter Tank Assembly for the ISS Urine Processor Assembly

Science.gov (United States)

Link, Dwight E., Jr.; Carter, Donald Layne; Higbie, Scott

2010-01-01

Recovering water from urine is a process that is critical to supporting larger crews for extended missions aboard the International Space Station. Urine is collected, preserved, and stored for processing into water and a concentrated brine solution that is highly toxic and must be contained to avoid exposure to the crew. The brine solution is collected in an accumulator tank, called a Recycle Filter Tank Assembly (RFTA) that must be replaced monthly and disposed in order to continue urine processing operations. In order to reduce resupply requirements, a new accumulator tank is being developed that can be emptied on orbit into existing ISS waste tanks. The new tank, called the Advanced Recycle Filter Tank Assembly (ARFTA) is a metal bellows tank that is designed to collect concentrated brine solution and empty by applying pressure to the bellows. This paper discusses the requirements and design of the ARFTA as well as integration into the urine processor assembly.

A real time analysis of the self-assembly process using thermal analysis inside the differential scanning calorimeter instrument.

Science.gov (United States)

Roy, Debmalya; Shastri, Babita; Mukhopadhyay, K

2012-07-12

The supramolecular assembly of the regioregular poly-3-hexylthiophene (rr-P3HT) in solution has been investigated thoroughly in the past. In the current study, our focus is on the enthalpy of nanofiber formation using thermal analysis techniques by performing the self-assembly process inside the differential scanning calorimetry (DSC) instrument. Thermogravimetric analysis (TGA) was carried out to check the concentration of the solvent during the self-assembly process of P3HT in p-xylene. Ultraviolet visible (UV-vis) spectophotometric technique, small-angle X-ray scattering (SAXS) experiment, atomic force microscopic (AFM), and scanning electron microscopic (SEM) images were used to characterize the different experimental yields generated by cooling the reaction mixture at desired temperatures. Comparison of the morphologies of self-assembled products at different fiber formation temperatures gives us an idea about the possible crystallization parameters which could affect the P3HT nanofiber morphology.

Reconstitutable control assembly having removable control rods with detachable split upper end plugs

International Nuclear Information System (INIS)

Gjertsen, R.K.; Knott, R.P.; Sparrow, J.A.

1989-01-01

This patent describes, in a reconstitutable control assembly for use with a nuclear fuel assembly, the control assembly including a spider structure and at least one control rod, an attachment joint for detachable fastening the control rod to the spider structure. The attachment joint comprising: a hollow connecting finger on the spider structure; and an elongated detachable split upper end plug on the control rod having a pair of separate upper and lower plug portions, the upper plug portion having integrally-connected tandemly- arranged upper, middle and lower sections. The lower plug portion having integrally-connected tandemly-arranged upper, middle and lower segments

Verification of communication protocols in web services model-checking service compositions

CERN Document Server

Tari, Zahir; Mukherjee, Anshuman

2014-01-01

Gathers recent advancements in the field of self-organizing wireless sensor networks and provides readers with the essential, state-of-the-art information about sensor networking. In the near future, wireless sensor networks will become an integral part of our day-to-day life. To solve different sensor networking related issues, researchers have put a great deal of effort into coming up with innovative ideas. Verification of Communication Protocols in Web Services: Model-Checking Service Compositions gathers recent advancements in the field of self-organizing wireless sensor networks and provides readers with integral information about sensor networking. It introduces current technological trends, particularly in node organization, and provides implementation details of each networking type to help readers set up sensor networks in their related job fields. In addition, it identifies the limitations of current technologies, as well as future research directions.

40 CFR 86.327-79 - Quench checks; NOX analyzer.

Science.gov (United States)

2010-07-01

... any flow rate into the reaction chamber. This includes, but is not limited to, sample capillary, ozone... Quench checks; NOX analyzer. (a) Perform the reaction chamber quench check for each model of high vacuum reaction chamber analyzer prior to initial use. (b) Perform the reaction chamber quench check for each new...

Development of a virtual manufacturing assembly simulation system

Directory of Open Access Journals (Sweden)

Abdulrahman M Al-Ahmari

2016-03-01

Full Text Available Assembly operations are a key component of modern manufacturing systems. Designing, planning, and conducting assembly operations represent an important part of the cost of a product. Virtual reality provides an efficient and cost-effective solution to manufacturing design, planning, and prototyping. Still there are certain issues (such as data translation, integration of various hardware and software systems, and real-time collision detection faced while applying this advanced technology to the assembly domain. For example, existing works focus on using virtual reality systems and environments mainly to design new products and to plan for assembly. Little focus has been given to develop virtual reality environments that contribute to train operators on assembly operations and to bridge the gap between design and implementation/execution of assembly. Therefore, the research work presented in this article focuses on developing a fully functional virtual manufacturing assembly simulation system that solves the issues related to virtual reality environments. The proposed system uses a virtual environment to create an interactive workbench that can be used for evaluating assembly decisions and training assembly operations. It is a comprehensive system that provides visual, auditory, tactile, as well as force feedback. The system works successfully even with large components.

Optical Assembly and Characterization System for Nano-Photonics Research

Science.gov (United States)

2016-03-01

freedoms) 3 (3) Carried out initial research work related to semiconductor membrane transfer printing. Based on the customer designed PDMS stamp...for optical characterization and membrane printing/assembly. The system has the following features: Micro-precision alignment with integrated 50 nm...a FL300-12 Automated Alignment System was acquired from Ficontec (USA) Corporation for optical characterization and membrane printing/assembly. The

NRC valve performance test program - check valve testing

International Nuclear Information System (INIS)

Jeanmougin, N.M.

1987-01-01

The Valve Performance Test Program addresses the current requirements for testing of pressure isolation valves (PIVs) in light water reactors. Leak rate monitoring is the current method used by operating commercial power plants to survey the condition of their PIVs. ETEC testing of three check valves (4-inch, 6-inch, and 12-inch nominal diameters) indicates that leak rate testing is not a reliable method for detecting impending valve failure. Acoustic emission monitoring of check valves shows promise as a method of detecting loosened internals damage. Future efforts will focus on evaluation of acoustic emission monitoring as a technique for determining check valve condition. Three gate valves also will be tested to evaluate whether the check valve results are applicable to gate type PIVs

Polymer cantilever platform for dielectrophoretic assembly of carbon nanotubes

DEFF Research Database (Denmark)

Johansson, Alicia; Calleja, M.; Dimaki, Maria

2004-01-01

A polymer cantilever platform for dielectrophoretic assembly of carbon nanotubes has been designed and realized. Multi-walled carbon nanotubes from aqueous solution have been assembled between two metal electrodes that are separated by 2 mu m and embedded in the polymer cantilever. The entire chip......, except for the metallic electrodes and wiring, was fabricated in the photoresist SU-8. SU-8 allows for an inexpensive, flexible and fast fabrication method, and the cantilever platform provides a hydrophobic surface that should be well suited for nanotube assembly. The device can be integrated in a micro...

12 CFR 229.36 - Presentment and issuance of checks.

Science.gov (United States)

2010-01-01

... Section 229.36 Banks and Banking FEDERAL RESERVE SYSTEM (CONTINUED) BOARD OF GOVERNORS OF THE FEDERAL RESERVE SYSTEM AVAILABILITY OF FUNDS AND COLLECTION OF CHECKS (REGULATION CC) Collection of Checks § 229... on the check, whether in magnetic ink or in fractional form; (3) At any branch or head office, if the...

FIZCON, ENDF/B Cross-Sections Redundancy Check

International Nuclear Information System (INIS)

Dunford, Charles L.

2007-01-01

1 - Description of program or function: FIZCON is a program for checking that an evaluated data file has valid data and conforms to recommended procedures. Version 7.01 (April 2005): set success flag after return from beginning; fixed valid level check for an isomer; fixed subsection energy range test in ckf9; changed lower limit on potential scattering test; fixed error in j-value test when l=0 and i=0; added one more significant figure to union grid check and sum up output messages; partial fission cross sections mt=19,20,21 and 38 did not require secondary energy distributions in file 5; corrected product test for elastic scattering; moved potential scattering test to psyche. Version 7.02 (May 2005): Fixed resonance parameter sum test. 2 - Method of solution: FIZCON can recognise the difference between ENDF-6 and ENDF-5 formats and performs its tests accordingly. Some of the tests performed include: data arrays are in increasing energy order; resonance parameter widths add up to the total; Q-values are reasonable and consistent; no required sections are missing and all cover the proper energy range; secondary distributions are normalized to 1.0; energy conservation in decay spectra. Optional tests can be performed to check the redundant cross sections, and algorithms can be used to check for possible incorrect entry of data values (Deviant Point test)

[Memory Checking Tests].

Science.gov (United States)

Hart, Joseph T.

Two basic tests for checking memory skills are included in these appendices. The first, the General Information Test, uses the same 150 items for each of its two versions. One version is a completion-type test which measures recall by requiring the examinee to supply a specific response. The other version supplements each of the 150 items with…

Check Sample Abstracts.

Science.gov (United States)

Alter, David; Grenache, David G; Bosler, David S; Karcher, Raymond E; Nichols, James; Rajadhyaksha, Aparna; Camelo-Piragua, Sandra; Rauch, Carol; Huddleston, Brent J; Frank, Elizabeth L; Sluss, Patrick M; Lewandrowski, Kent; Eichhorn, John H; Hall, Janet E; Rahman, Saud S; McPherson, Richard A; Kiechle, Frederick L; Hammett-Stabler, Catherine; Pierce, Kristin A; Kloehn, Erica A; Thomas, Patricia A; Walts, Ann E; Madan, Rashna; Schlesinger, Kathie; Nawgiri, Ranjana; Bhutani, Manoop; Kanber, Yonca; Abati, Andrea; Atkins, Kristen A; Farrar, Robert; Gopez, Evelyn Valencerina; Jhala, Darshana; Griffin, Sonya; Jhala, Khushboo; Jhala, Nirag; Bentz, Joel S; Emerson, Lyska; Chadwick, Barbara E; Barroeta, Julieta E; Baloch, Zubair W; Collins, Brian T; Middleton, Owen L; Davis, Gregory G; Haden-Pinneri, Kathryn; Chu, Albert Y; Keylock, Joren B; Ramoso, Robert; Thoene, Cynthia A; Stewart, Donna; Pierce, Arand; Barry, Michelle; Aljinovic, Nika; Gardner, David L; Barry, Michelle; Shields, Lisa B E; Arnold, Jack; Stewart, Donna; Martin, Erica L; Rakow, Rex J; Paddock, Christopher; Zaki, Sherif R; Prahlow, Joseph A; Stewart, Donna; Shields, Lisa B E; Rolf, Cristin M; Falzon, Andrew L; Hudacki, Rachel; Mazzella, Fermina M; Bethel, Melissa; Zarrin-Khameh, Neda; Gresik, M Vicky; Gill, Ryan; Karlon, William; Etzell, Joan; Deftos, Michael; Karlon, William J; Etzell, Joan E; Wang, Endi; Lu, Chuanyi M; Manion, Elizabeth; Rosenthal, Nancy; Wang, Endi; Lu, Chuanyi M; Tang, Patrick; Petric, Martin; Schade, Andrew E; Hall, Geraldine S; Oethinger, Margret; Hall, Geraldine; Picton, Avis R; Hoang, Linda; Imperial, Miguel Ranoa; Kibsey, Pamela; Waites, Ken; Duffy, Lynn; Hall, Geraldine S; Salangsang, Jo-Anne M; Bravo, Lulette Tricia C; Oethinger, Margaret D; Veras, Emanuela; Silva, Elvia; Vicens, Jimena; Silva, Elvio; Keylock, Joren; Hempel, James; Rushing, Elizabeth; Posligua, Lorena E; Deavers, Michael T; Nash, Jason W; Basturk, Olca; Perle, Mary Ann; Greco, Alba; Lee, Peng; Maru, Dipen; Weydert, Jamie Allen; Stevens, Todd M; Brownlee, Noel A; Kemper, April E; Williams, H James; Oliverio, Brock J; Al-Agha, Osama M; Eskue, Kyle L; Newlands, Shawn D; Eltorky, Mahmoud A; Puri, Puja K; Royer, Michael C; Rush, Walter L; Tavora, Fabio; Galvin, Jeffrey R; Franks, Teri J; Carter, James Elliot; Kahn, Andrea Graciela; Lozada Muñoz, Luis R; Houghton, Dan; Land, Kevin J; Nester, Theresa; Gildea, Jacob; Lefkowitz, Jerry; Lacount, Rachel A; Thompson, Hannis W; Refaai, Majed A; Quillen, Karen; Lopez, Ana Ortega; Goldfinger, Dennis; Muram, Talia; Thompson, Hannis

2009-02-01

The following abstracts are compiled from Check Sample exercises published in 2008. These peer-reviewed case studies assist laboratory professionals with continuing medical education and are developed in the areas of clinical chemistry, cytopathology, forensic pathology, hematology, microbiology, surgical pathology, and transfusion medicine. Abstracts for all exercises published in the program will appear annually in AJCP.

Controllable assembly of silver nanoparticles induced by femtosecond laser direct writing

International Nuclear Information System (INIS)

Wang, Huan; Liu, Sen; Zhang, Yong-Lai; Wang, Jian-Nan; Wang, Lei; Xia, Hong; Chen, Qi-Dai; Sun, Hong-Bo; Ding, Hong

2015-01-01

We report controllable assembly of silver nanoparticles (Ag NPs) for patterning of silver microstructures. The assembly is induced by femtosecond laser direct writing (FsLDW). A tightly focused femtosecond laser beam is capable of trapping and driving Ag NPs to form desired micropatterns with a high resolution of ∼190 nm. Taking advantage of the ‘direct writing’ feature, three microelectrodes have been integrated with a microfluidic chip; two silver-based microdevices including a microheater and a catalytic reactor have been fabricated inside a microfluidic channel for chip functionalization. The FsLDW-induced programmable assembly of Ag NPs may open up a new way to the designable patterning of silver microstructures toward flexible fabrication and integration of functional devices. (focus issue paper)

High-power fused assemblies enabled by advances in fiber-processing technologies

Science.gov (United States)

Wiley, Robert; Clark, Brett

2011-02-01

The power handling capabilities of fiber lasers are limited by the technologies available to fabricate and assemble the key optical system components. Previous tools for the assembly, tapering, and fusion of fiber laser elements have had drawbacks with regard to temperature range, alignment capability, assembly flexibility and surface contamination. To provide expanded capabilities for fiber laser assembly, a wide-area electrical plasma heat source was used in conjunction with an optimized image analysis method and a flexible alignment system, integrated according to mechatronic principles. High-resolution imaging and vision-based measurement provided feedback to adjust assembly, fusion, and tapering process parameters. The system was used to perform assembly steps including dissimilar-fiber splicing, tapering, bundling, capillary bundling, and fusion of fibers to bulk optic devices up to several mm in diameter. A wide range of fiber types and diameters were tested, including extremely large diameters and photonic crystal fibers. The assemblies were evaluated for conformation to optical and mechanical design criteria, such as taper geometry and splice loss. The completed assemblies met the performance targets and exhibited reduced surface contamination compared to assemblies prepared on previously existing equipment. The imaging system and image analysis algorithms provided in situ fiber geometry measurement data that agreed well with external measurement. The ability to adjust operating parameters dynamically based on imaging was shown to provide substantial performance benefits, particularly in the tapering of fibers and bundles. The integrated design approach was shown to provide sufficient flexibility to perform all required operations with a minimum of reconfiguration.

The Detector Control System of the ATLAS SemiCondutor Tracker during Macro-Assembly and Integration

CERN Document Server

Abdesselam, A; Basiladze, S; Bates, R L; Bell, P; Bingefors, N; Böhm, J; Brenner, R; Chamizo-Llatas, M; Clark, A; Codispoti, G; Colijn, A P; D'Auria, S; Dorholt, O; Doherty, F; Ferrari, P; Ferrère, D; Górnicki, E; Koperny, S; Lefèvre, R; Lindquist, L-E; Malecki, P; Mikulec, B; Mohn, B; Pater, J; Pernegger, H; Phillips, P; Robichaud-Véronneau, A; Robinson, D; Roe, S; Sandaker, H; Sfyrla, A; Stanecka, E; Stastny, J; Viehhauser, G; Vossebeld, J; Wells, P

2008-01-01

The ATLAS SemiConductor Tracker (SCT) is one of the largest existing semiconductor detectors. It is situated between the Pixel detector and the Transition Radiation Tracker at one of the four interaction points of the Large Hadron Collider (LHC). During 2006-2007 the detector was lowered into the ATLAS cavern and installed in its final position. For the assembly, integration and commissioning phase, a complete Detector Control System (DCS) was developed to ensure the safe operation of the tracker. This included control of the individual powering of the silicon modules, a bi-phase cooling system and various types of sensors monitoring the SCT environment and the surrounding test enclosure. The DCS software architecture, performance and operational experience will be presented in the view of a validation of the DCS for the final SCT installation and operation phase.

Implementing Model-Check for Employee and Management Satisfaction

Science.gov (United States)

Jones, Corey; LaPha, Steven

2013-01-01

This presentation will discuss methods to which ModelCheck can be implemented to not only improve model quality, but also satisfy both employees and management through different sets of quality checks. This approach allows a standard set of modeling practices to be upheld throughout a company, with minimal interaction required by the end user. The presenter will demonstrate how to create multiple ModelCheck standards, preventing users from evading the system, and how it can improve the quality of drawings and models.

Co-Check: Collaborative Outsourced Data Auditing in Multicloud Environment

Directory of Open Access Journals (Sweden)

Jian Mao

2017-01-01

Full Text Available With the increasing demand for ubiquitous connectivity, wireless technology has significantly improved our daily lives. Meanwhile, together with cloud-computing technology (e.g., cloud storage services and big data processing, new wireless networking technology becomes the foundation infrastructure of emerging communication networks. Particularly, cloud storage has been widely used in services, such as data outsourcing and resource sharing, among the heterogeneous wireless environments because of its convenience, low cost, and flexibility. However, users/clients lose the physical control of their data after outsourcing. Consequently, ensuring the integrity of the outsourced data becomes an important security requirement of cloud storage applications. In this paper, we present Co-Check, a collaborative multicloud data integrity audition scheme, which is based on BLS (Boneh-Lynn-Shacham signature and homomorphic tags. According to the proposed scheme, clients can audit their outsourced data in a one-round challenge-response interaction with low performance overhead. Our scheme also supports dynamic data maintenance. The theoretical analysis and experiment results illustrate that our scheme is provably secure and efficient.

Accurate DNA assembly and genome engineering with optimized uracil excision cloning

DEFF Research Database (Denmark)

Cavaleiro, Mafalda; Kim, Se Hyeuk; Seppala, Susanna

2015-01-01

Simple and reliable DNA editing by uracil excision (a.k.a. USER cloning) has been described by several research groups, but the optimal design of cohesive DNA ends for multigene assembly remains elusive. Here, we use two model constructs based on expression of gfp and a four-gene pathway that pro......Simple and reliable DNA editing by uracil excision (a.k.a. USER cloning) has been described by several research groups, but the optimal design of cohesive DNA ends for multigene assembly remains elusive. Here, we use two model constructs based on expression of gfp and a four-gene pathway...... that produces β-carotene to optimize assembly junctions and the uracil excision protocol. By combining uracil excision cloning with a genomic integration technology, we demonstrate that up to six DNA fragments can be assembled in a one-tube reaction for direct genome integration with high accuracy, greatly...... facilitating the advanced engineering of robust cell factories....

Ultra-Portable Smartphone Controlled Integrated Digital Microfluidic System in a 3D-Printed Modular Assembly

Directory of Open Access Journals (Sweden)

Mohamed Yafia

2015-09-01

Full Text Available Portable sensors and biomedical devices are influenced by the recent advances in microfluidics technologies, compact fabrication techniques, improved detection limits and enhanced analysis capabilities. This paper reports the development of an integrated ultraportable, low-cost, and modular digital microfluidic (DMF system and its successful integration with a smartphone used as a high-level controller and post processing station. Low power and cost effective electronic circuits are designed to generate the high voltages required for DMF operations in both open and closed configurations (from 100 to 800 V. The smartphone in turn commands a microcontroller that manipulate the voltage signals required for droplet actuation in the DMF chip and communicates wirelessly with the microcontroller via Bluetooth module. Moreover, the smartphone acts as a detection and image analysis station with an attached microscopic lens. The holder assembly is fabricated using three-dimensional (3D printing technology to facilitate rapid prototyping. The holder features a modular design that enables convenient attachment/detachment of a variety of DMF chips to/from an electrical busbar. The electrical circuits, controller and communication system are designed to minimize the power consumption in order to run the device on small lithium ion batteries. Successful controlled DMF operations and a basic colorimetric assay using the smartphone are demonstrated.

The criticality check and its applicability for nuclear material accounting

International Nuclear Information System (INIS)

Sanchez Espinoza, V.H.; Adam, E.; Knorr, J.

1988-01-01

Different procedures are used by the realization of nuclear material check by the IAEA. The criticality check belongs to these methods and it appropriates especially to verification of the nuclear material inventory of reactors. General aspects of the applicability of this check procedure are formulated and application criteria are deduced. By the example of solid-moderated homogeneous zero-power reactors it is demonstrated the unsecurity which is to be reckoned by applying the criticality check. Finally a possibility for the reduction of errors in core material determination by additional measuring methods without questioning the criticality check method is presented. (author)

Targeted assembly of short sequence reads.

Directory of Open Access Journals (Sweden)

René L Warren

Full Text Available As next-generation sequence (NGS production continues to increase, analysis is becoming a significant bottleneck. However, in situations where information is required only for specific sequence variants, it is not necessary to assemble or align whole genome data sets in their entirety. Rather, NGS data sets can be mined for the presence of sequence variants of interest by localized assembly, which is a faster, easier, and more accurate approach. We present TASR, a streamlined assembler that interrogates very large NGS data sets for the presence of specific variants by only considering reads within the sequence space of input target sequences provided by the user. The NGS data set is searched for reads with an exact match to all possible short words within the target sequence, and these reads are then assembled stringently to generate a consensus of the target and flanking sequence. Typically, variants of a particular locus are provided as different target sequences, and the presence of the variant in the data set being interrogated is revealed by a successful assembly outcome. However, TASR can also be used to find unknown sequences that flank a given target. We demonstrate that TASR has utility in finding or confirming genomic mutations, polymorphisms, fusions and integration events. Targeted assembly is a powerful method for interrogating large data sets for the presence of sequence variants of interest. TASR is a fast, flexible and easy to use tool for targeted assembly.

Calibration and check light source

Energy Technology Data Exchange (ETDEWEB)

Nejedla, B; Krotil, J

1979-02-15

The light source is designed for calibrating photomultipliers and checking the function of the thermoluminescent dosemeters evaluation equipment. The check light source consists of a polymer material-based (polyvinyl toluene) plastic scintillator and a 2-phenyl-5-(4-bisphenyl)-1,3,4-oxadiazol and/or paraterphenyl activator, and of emission spectrum shifters for response in the green and the blue light regions. The plastic scintillator is sealed in a case to whose bottom a radiation source is fixed, such as a /sup 90/Sr-/sup 90/Y source of an activity of 1.85x10/sup 3/s/sup -1/ to 0.74x10/sup 9/s/sup -1/.

Pre-assembling electric circuits of braided conductors

International Nuclear Information System (INIS)

Mercado Gomez, Martin Elias

1999-01-01

The present article has for object to give to know an innovative concept of pre-assembling electric circuits for distribution of normal and regulated power, to the work position like integral subsystems of the calls intelligent buildings

Opto-mechanical assembly procurement for the National Ignition Facility

International Nuclear Information System (INIS)

House, W.; Simon, T.

1999-01-01

A large number of the small optics procurements for the National Ignition Facility (NIF) at Lawrence Livermore National Laboratory (LLNL) will be in the form of completely assembled, tested, and cleaned subsystems. These subsystems will be integrated into the NIF at LLNL. To accomplish this task, the procurement packages will include, optical and mechanical drawings, acceptance test and cleanliness requirements. In January 1999, the first such integrated opto-mechanical assembly was received and evaluated at LLNL. With the successful completion of this important trial procurement, we were able to establish the viability of purchasing clean, ready to install, opto-mechanical assemblies from vendors within the optics industry. 32 vendors were chosen from our supplier database for quote, then five were chosen to purchase from. These five vendors represented a cross section of the optics industry. From a ''value'' catalog supplier (that did the whole job internally) to a partnership between three specialty companies, these vendors demonstrated they have the ingenuity and capability to deliver cost competitive, NIF-ready, opto- mechanical assemblies. This paper describes the vendor selection for this procurement, technical requirements including packaging, fabrication, coating, and cleanliness specifications, then testing and verification. It also gives real test results gathered from inspections performed at LLNL that show how our vendors scored on the various requirements. Keywords: Opto-Mechanical, assembly, NIF, packaging, shipping, specifications, procurement, MIL-STD-1246C, surface cleanliness

Patterning of self-assembled monolayers by phase-shifting mask and its applications in large-scale assembly of nanowires

Energy Technology Data Exchange (ETDEWEB)

Gao, Fan; Zhang, Dakuan; Wang, Jianyu; Sheng, Yun; Wang, Xinran; Chen, Kunji; Zhou, Minmin [Key Laboratory of Advanced Photonic and Electronic Materials and School of Electronic Science and Engineering, Nanjing University, Nanjing 210093 (China); Yan, Shancheng [Key Laboratory of Advanced Photonic and Electronic Materials and School of Electronic Science and Engineering, Nanjing University, Nanjing 210093 (China); School of Geography and Biological Information, Nanjing University of Posts and Telecommunications, Nanjing 210046 (China); Shen, Jiancang; Pan, Lijia; Shi, Yi, E-mail: yshi@nju.edu.cn [Key Laboratory of Advanced Photonic and Electronic Materials and School of Electronic Science and Engineering, Nanjing University, Nanjing 210093 (China); Collaborative Innovation Center of Advanced Micro-structures, Nanjing University, Nanjing 210093 (China)

2015-01-26

A nonselective micropatterning method of self-assembled monolayers (SAMs) based on laser and phase-shifting mask (PSM) is demonstrated. Laser beam is spatially modulated by a PSM, and periodic SAM patterns are generated sequentially through thermal desorption. Patterned wettability is achieved with alternating hydrophilic/hydrophobic stripes on octadecyltrichlorosilane monolayers. The substrate is then used to assemble CdS semiconductor nanowires (NWs) from a solution, obtaining well-aligned NWs in one step. Our results show valuably the application potential of this technique in engineering SAMs for integration of functional devices.

26 CFR 301.6657-1 - Bad checks.

Science.gov (United States)

2010-04-01

... 26 Internal Revenue 18 2010-04-01 2010-04-01 false Bad checks. 301.6657-1 Section 301.6657-1... Additions to the Tax and Additional Amounts § 301.6657-1 Bad checks. (a) In general. Except as provided in... district director that it was tendered in good faith with reasonable cause to believe that it would be duly...

Vertical pump with free floating check valve

International Nuclear Information System (INIS)

Lindsay, M.

1980-01-01

A vertical pump is described which has a bottom discharge with a free floating check valve disposed in the outlet plenum thereof. The free floating check valve comprises a spherical member with a hemispherical cage-like member attached thereto which is capable of allowing forward or reverse flow under appropriate conditions while preventing reverse flow under inappropriate conditions

A Framework for Geometric Reasoning About Human Figures and Factors in Assembly Processes

Energy Technology Data Exchange (ETDEWEB)

Calton, Terri L.

1999-07-20

Automatic assembly sequencing and visualization tools are valuable in determining the best assembly sequences, but without Human Factors and Figure Models (HFFMs) it is difficult to evaluate or visualize human interaction. In industry, accelerating technological advances and shorter market windows have forced companies to turn to an agile manufacturing paradigm. This trend has promoted computerized automation of product design and manufacturing processes, such as automated assembly planning. However, all automated assembly planning software tools assume that the individual components fly into their assembled configuration and generate what appear to be perfectly valid operations, but in reality some operations cannot physically be carried out by a human. For example, the use of a ratchet may be reasoned feasible for an assembly operation; however, when a hand is placed on the tool the operation is no longer feasible, perhaps because of inaccessibility, insufficient strength or human interference with assembly components. Similarly, human figure modeling algorithms may indicate that assembly operations are not feasible and consequently force design modifications, however, if they had the capability to quickly generate alternative assembly sequences, they might have identified a feasible solution. To solve this problem, HFFMs must be integrated with automated assembly planning which allows engineers to quickly verify that assembly operations are possible and to see ways to make the designs even better. This paper presents a framework for integrating geometry-based assembly planning algorithms with commercially available human figure modeling software packages. Experimental results to selected applications along with lessons learned are presented.

Consistency check of iron and sodium cross sections with integral benchmark experiments using a large amount of experimental information

International Nuclear Information System (INIS)

Baechle, R.-D.; Hehn, G.; Pfister, G.; Perlini, G.; Matthes, W.

1984-01-01

Single material benchmark experiments are designed to check neutron and gamma cross-sections of importance for deep penetration problems. At various penetration depths a large number of activation detectors and spectrometers are placed to measure the radiation field as completely as possible. The large amount of measured data in benchmark experiments can be evaluated best by the global detector concept applied to nuclear data adjustment. A new iteration procedure is presented for adjustment of a large number of multigroup cross sections, which has been implemented now in the modular adjustment code ADJUST-EUR. A theoretical test problem has been deviced to check the total program system with high precision. The method and code are going to be applied for validating the new European Data Files (JEF and EFF) in progress. (Auth.)

Force-controlled robotic assembly processes of rigid and flexible objects methodologies and applications

CERN Document Server

Ghalyan, Ibrahim Fahad Jasim

2016-01-01

This book provides comprehensive and integrated approaches for rigid and flexible object assembly. It presents comparison studies with the available force-guided robotic processes and covers contact-state modeling, scheme control strategies, and position searching algorithms. Further, it includes experimental validations for different assembly situations, including those for the assembly of industrial parts taken from the automotive industry. .

Multifunctional Materials Based on Self Assembly of Molecular Nanostructures

National Research Council Canada - National Science Library

Stupp, Samuel

2001-01-01

.... The objective was to integrate self assembly, encoded in the triblock structure, luminescent properties, and the properties characteristic of materials that have macroscopically polar structure...

STABILITAS CHECK DAM DI ARBORETUM DESA SUMBER BRANTAS

Directory of Open Access Journals (Sweden)

Endang Purwati

2012-09-01

Full Text Available Abstract: The stability of check-dam in arboretum of Sumber Brantas village. Sumber Brantas water sources area is arboretum territory which has to be maintained as conservation either for technical or vegetation (plants cover by sustainable development. Arboretum territory is made as asylum in irrigation system district of Brantas River. This research discusses technical conservation activity to build the check dam in conserving the area. Check dam is built dimensionally by using HEC-RAS Program to get safe and stable dimension for rolling, shifting and piping of Sf > 1.5, and based on hydrologic analysis to get maximum flood discharge of 48.01 m3second-1. Hydraulic analysis is used to get water level profile and pressure for the dam body. Stability of the structure will be controlled by construction load (weight of check dam and its fully sediment storage condition. The result of this research shows that the safe and stable dimension for check dam are as follows: 28 meter of width; 3 meter of main height; 1.5 meter of sub-height; 10 meter of stilling basin length (Main Dam–Sub Dam.

Model Checking Temporal Logic Formulas Using Sticker Automata

Science.gov (United States)

Feng, Changwei; Wu, Huanmei

2017-01-01

As an important complex problem, the temporal logic model checking problem is still far from being fully resolved under the circumstance of DNA computing, especially Computation Tree Logic (CTL), Interval Temporal Logic (ITL), and Projection Temporal Logic (PTL), because there is still a lack of approaches for DNA model checking. To address this challenge, a model checking method is proposed for checking the basic formulas in the above three temporal logic types with DNA molecules. First, one-type single-stranded DNA molecules are employed to encode the Finite State Automaton (FSA) model of the given basic formula so that a sticker automaton is obtained. On the other hand, other single-stranded DNA molecules are employed to encode the given system model so that the input strings of the sticker automaton are obtained. Next, a series of biochemical reactions are conducted between the above two types of single-stranded DNA molecules. It can then be decided whether the system satisfies the formula or not. As a result, we have developed a DNA-based approach for checking all the basic formulas of CTL, ITL, and PTL. The simulated results demonstrate the effectiveness of the new method. PMID:29119114

Deployment of check-in nodes in complex networks

Science.gov (United States)

Jiang, Zhong-Yuan; Ma, Jian-Feng

2017-01-01

In many real complex networks such as the city road networks and highway networks, vehicles often have to pass through some specially functioned nodes to receive check-in like services such as gas supplement at gas stations. Based on existing network structures, to guarantee every shortest path including at least a check-in node, the location selection of all check-in nodes is very essential and important to make vehicles to easily visit these check-in nodes, and it is still remains an open problem in complex network studies. In this work, we aim to find possible solutions for this problem. We first convert it into a set cover problem which is NP-complete and propose to employ the greedy algorithm to achieve an approximate result. Inspired by heuristic information of network structure, we discuss other four check-in node location deployment methods including high betweenness first (HBF), high degree first (HDF), random and low degree first (LDF). Finally, we compose extensive simulations in classical scale-free networks, random networks and real network models, and the results can well confirm the effectiveness of the greedy algorithm. This work has potential applications into many real networks.

Types for DSP Assembler Programs

DEFF Research Database (Denmark)

Larsen, Ken

2006-01-01

for reuse, and a procedure that computes point-wise vector multiplication. The latter uses a common idiom of prefetching memory resulting in out-of-bounds reading from memory. I present two extensions to the baseline type system: The first extension is a simple modification of some type rules to allow out......-ofbounds reading from memory. The second extension is based on two major modifications of the baseline type system: • Abandoning the type-invariance principle of memory locations and using a variation of alias types instead. • Introducing aggregate types, making it possible to have different views of a block...... of memory, thus enabling type checking of programs that directly manage and reuse memory. I show that both the baseline type system and the extended type system can be used to give type annotations to handwritten DSP assembler code, and that these annotations precisely and succinctly describe...

The impact of gender on the assessment of body checking behavior.

Science.gov (United States)

Alfano, Lauren; Hildebrandt, Tom; Bannon, Katie; Walker, Catherine; Walton, Kate E

2011-01-01

Body checking includes any behavior aimed at global or specific evaluations of appearance characteristics. Men and women are believed to express these behaviors differently, possibly reflecting different socialization. However, there has been no empirical test of the impact of gender on body checking. A total of 1024 male and female college students completed two measures of body checking, the Body Checking Questionnaire and the Male Body Checking Questionnaire. Using multiple group confirmatory factor analysis, differential item functioning (DIF) was explored in a composite of these measures. Two global latent factors were identified (female and male body checking severity), and there were expected gender differences in these factors even after controlling for DIF. Ten items were found to be unbiased by gender and provide a suitable brief measure of body checking for mixed gender research. Practical applications for body checking assessment and theoretical implications are discussed. Copyright © 2010 Elsevier Ltd. All rights reserved.

Compliance checking of data-aware and resource-aware compliance requirements

NARCIS (Netherlands)

Ramezani Taghiabadi, E.; Gromov, V.; Fahland, D.; Aalst, van der W.M.P.; Meersman, R.; Panetto, H.; Dillon, T.; Missikoff, M.; Liu, L.; Pastor, O.; Cuzzocrea, A.; Sllis, T.

2014-01-01

Compliance checking is gaining importance as today’s organizations need to show that their business practices are in accordance with predefined (legal) requirements. Current compliance checking techniques are mostly focused on checking the control-flow perspective of business processes. This paper

OntoCheck: verifying ontology naming conventions and metadata completeness in Protégé 4.

Science.gov (United States)

Schober, Daniel; Tudose, Ilinca; Svatek, Vojtech; Boeker, Martin

2012-09-21

Although policy providers have outlined minimal metadata guidelines and naming conventions, ontologies of today still display inter- and intra-ontology heterogeneities in class labelling schemes and metadata completeness. This fact is at least partially due to missing or inappropriate tools. Software support can ease this situation and contribute to overall ontology consistency and quality by helping to enforce such conventions. We provide a plugin for the Protégé Ontology editor to allow for easy checks on compliance towards ontology naming conventions and metadata completeness, as well as curation in case of found violations. In a requirement analysis, derived from a prior standardization approach carried out within the OBO Foundry, we investigate the needed capabilities for software tools to check, curate and maintain class naming conventions. A Protégé tab plugin was implemented accordingly using the Protégé 4.1 libraries. The plugin was tested on six different ontologies. Based on these test results, the plugin could be refined, also by the integration of new functionalities. The new Protégé plugin, OntoCheck, allows for ontology tests to be carried out on OWL ontologies. In particular the OntoCheck plugin helps to clean up an ontology with regard to lexical heterogeneity, i.e. enforcing naming conventions and metadata completeness, meeting most of the requirements outlined for such a tool. Found test violations can be corrected to foster consistency in entity naming and meta-annotation within an artefact. Once specified, check constraints like name patterns can be stored and exchanged for later re-use. Here we describe a first version of the software, illustrate its capabilities and use within running ontology development efforts and briefly outline improvements resulting from its application. Further, we discuss OntoChecks capabilities in the context of related tools and highlight potential future expansions. The OntoCheck plugin facilitates

UK Department of Environment Quality Checking Laboratory

International Nuclear Information System (INIS)

Burgoyne, K.E.; Green, T.H.; Maxwell, D.J.; Smith, D.L.G.

1990-01-01

The purpose of Taywood Engineering Ltd was to develop and evaluate techniques for the non-destructive and destructive examination of both low and intermediate level radioactive waste packages. The contract also included a study on the conceptual design and cost of a permanent Waste Quality Checking facility. The June 1986 contract was completed in November 1989. A second contract was awarded in September 1989 to extend the scope to include Quality Checking of hazardous waste and to increase the throughput of low level waste. This paper highlights the techniques developed during these programmes and applied to a range of real low level waste packages. The feasibility of operating a pilot scale facility for the independent Quality Checking of LLW has been successfully demonstrated. (orig.)

Model checking exact cost for attack scenarios

DEFF Research Database (Denmark)

Aslanyan, Zaruhi; Nielson, Flemming

2017-01-01

Attack trees constitute a powerful tool for modelling security threats. Many security analyses of attack trees can be seamlessly expressed as model checking of Markov Decision Processes obtained from the attack trees, thus reaping the benefits of a coherent framework and a mature tool support....... However, current model checking does not encompass the exact cost analysis of an attack, which is standard for attack trees. Our first contribution is the logic erPCTL with cost-related operators. The extended logic allows to analyse the probability of an event satisfying given cost bounds and to compute...... the exact cost of an event. Our second contribution is the model checking algorithm for erPCTL. Finally, we apply our framework to the analysis of attack trees....

COMMON AGRICULTURAL POLICY FROM HEALTH CHECK DECISIONS TO THE POST-2013 REFORM

Directory of Open Access Journals (Sweden)

Niculescu Oana Marilena

2011-07-01

Full Text Available The paper proposed for being presented belongs to the field research International Affairs and European Integration. The paper entitled Common Agricultural Policy from Health Check decisions to the post-2013 reform aims to analyze the Common Agricultural Policy (CAP from the Health Check adoption in November 2008 to a new reform post-2013. The objectives of the paper are the presentation of the Health Check with its advantages and disadvantages as well as the analysis of the opportunity of a new European policy and its reforming having in view that the analysis of Health Check condition was considered a compromise. The paper is related to the internal and international research consisting in several books, studies, documents that analyze the particularities of the most debated, controversial and reformed EU policy. A personal study is represented by the first report within the PhD paper called The reform of CAP and its implications for Romanias agriculture(coordinator prof. Gheorghe Hurduzeu PhD, Academy of Economic Studies Bucharest, Faculty of International Business, research studies in the period 2009-2012. The research methodology used consists in collecting and analysis data from national and international publications, their validation, followed by a dissemination of the results in order to express a personal opinion regarding CAP and its reform. The results of the research consist in proving the opportunity of a new reform due to the fact that Health Check belongs already to the past. The paper belongs to the field research mentioned, in the attempt to prove the opportunity of building a new EU agricultural policy. The challenges CAP is facing are: food safety, environmental and climate changes, territorial balance as well as new challenges-improving sustainable management of natural resources, maintaining competitiveness in the context of globalization growth, strengthening EU cohesion in rural areas, increasing the support of CAP for

The Belle II silicon vertex detector assembly and mechanics

Energy Technology Data Exchange (ETDEWEB)

Adamczyk, K. [H. Niewodniczanski Institute of Nuclear Physics, Krakow 31-342 (Poland); Aihara, H. [Department of Physics, University of Tokyo, Tokyo 113-0033 (Japan); Angelini, C. [Dipartimento di Fisica, Università di Pisa, I-56127 Pisa (Italy); INFN Sezione di Pisa, I-56127 Pisa (Italy); Aziz, T.; Babu, V. [Tata Institute of Fundamental Research, Mumbai 400005 (India); Bacher, S. [H. Niewodniczanski Institute of Nuclear Physics, Krakow 31-342 (Poland); Bahinipati, S. [Indian Institute of Technology Bhubaneswar, Satya Nagar (India); Barberio, E.; Baroncelli, Ti.; Baroncelli, To. [School of Physics, University of Melbourne, Melbourne, Victoria 3010 (Australia); Basith, A.K. [Indian Institute of Technology Madras, Chennai 600036 (India); Batignani, G. [Dipartimento di Fisica, Università di Pisa, I-56127 Pisa (Italy); INFN Sezione di Pisa, I-56127 Pisa (Italy); Bauer, A. [Institute of High Energy Physics, Austrian Academy of Sciences, 1050 Vienna (Austria); Behera, P.K. [Indian Institute of Technology Madras, Chennai 600036 (India); Bergauer, T. [Institute of High Energy Physics, Austrian Academy of Sciences, 1050 Vienna (Austria); Bettarini, S., E-mail: stefano.bettarini@pi.infn.it [Dipartimento di Fisica, Università di Pisa, I-56127 Pisa (Italy); INFN Sezione di Pisa, I-56127 Pisa (Italy); Bhuyan, B. [Indian Institute of Technology Guwahati, Assam 781039 (India); Bilka, T. [Faculty of Mathematics and Physics, Charles University, 121 16 Prague (Czech Republic); Bosi, F. [INFN Sezione di Pisa, I-56127 Pisa (Italy); Bosisio, L. [Dipartimento di Fisica, Università di Trieste, I-34127 Trieste (Italy); INFN Sezione di Trieste, I-34127 Trieste (Italy); and others

2017-02-11

The Belle II experiment at the asymmetric SuperKEKB collider in Japan will operate at an instantaneous luminosity approximately 50 times greater than its predecessor (Belle). The central feature of the experiment is a vertex detector comprising two layers of pixelated silicon detectors (PXD) and four layers of double-sided silicon microstrip detectors (SVD). One of the key measurements for Belle II is CP violation asymmetry in the decays of beauty and charm hadrons, which hinges on a precise charged-track vertex determination and low-momentum track measurement. Towards this goal, a proper assembly of the SVD components with precise alignment ought to be performed and the geometrical tolerances should be checked to fall within the design limits. We present an overview of the assembly procedure that is being followed, which includes the precision gluing of the SVD module components, wire-bonding of the various electrical components, and precision 3D coordinate measurements of the final SVD modules. Finally, some results from the latest test-beam are reported.

Linear pulse motor type control element drive mechanism for the integral reactor

International Nuclear Information System (INIS)

Yu, J. Y.; Choi, S.; Kim, J. H.; Huh, H.; Park, K. B.

2007-01-01

The integral reactor SMART currently under development at Korea Atomic Energy Research Institute is designed with soluble boron free operation and use of nuclear heating for reactor startup. These design features require the Control Element Drive Mechanism (CEDM) for SMART to have fine-step movement capability as well as high reliability for the fine reactivity control. In this paper, design characteristics of a new concept CEDM driven by the Linear Pulse Motor (LPM) which meets the design requirements of the integral reactor SMART are introduced. The primary dimensions of the linear pulse motor are determined by the electro-magnetic analysis and the results are also presented. In parallel with the electro-magnetic analysis, the conceptual design of the CEDM is visualized and checked for interferences among parts by assembling three dimensional (3D) models on the computer. Prototype of LPM with double air-gaps for the CEDM sub-assemblies to lift 100 kg is designed, analysed, manufactured and tested to confirm the validity of the CEDM design concept. A converter and a test facility are manufactured to verify the dynamic performance of the LPM. The mover of the LPM is welded with ferromagnetic material and non-ferromagnetic material to get the magnetic flux path between inner stator and outer stator. The thrust forces of LPM predicted by analytic model have shown good agreement with experimental results from the prototype LPM. It is found that the LPM type CEDM has high force density and simple drive mechanism to reduce volume and satisfy the reactor operating circumstances with high pressure and temperature

A self-checking identification formula for radiation workers in India

International Nuclear Information System (INIS)

Srivastava, D.N.; Srivastava, M.K.; Gohel, Chetna; Kher, R.K.; Awari, J.M.; Joshi, V.D.

1998-01-01

Accurate monitoring of radiation exposure of workers in any nuclear installation, institution or laboratory handling radiation sources forms an integral part of the radiation protection programme. This requires a system of unique identification of each radiation worker. When the radiation monitoring service started in India in 1953, the first identification formula of six digits was allotted to each radiation worker. This formula remained in use till 1970. With more number of institutions coming up, in the due course a second identification formula of eight digits was introduced which was in use during the period 1971-1978. For better data processing, a third identification formula of the same number of digits was introduced in 1978 with specific information about the category and location of the institution. To account for increasing number of institutions, a fourth formula consisting of 10 digits was started in 1995 which is currently in use. However, none of these formulas contained personal information about the radiation worker. Moreover, they were not self-checking type. Self-checking ability is extremely important for the preparation of a systematic data base and error free flow of information. With these considerations, a new 14 digit self-checking formula is being proposed in this report. Besides being less prone to error, it gives information in respect of date of birth, sex, institution category, location etc.. It does not suffer from the problem of millennium at the turn of century. It has enough capacity to account for a large number of institutions of different categories that might come up in future, and very large number of radiation workers in each institution. The inclusion of date of birth in a suitable format makes the capacity of the system virtually limitless and perpetual. (author)

Context-aware compliance checking

NARCIS (Netherlands)

Werf, van der J.M.E.M.; Verbeek, H.M.W.; Aalst, van der W.M.P.; Barros, A.; Gal, A.; Kindler, E.

2012-01-01

Organizations face more and more the burden to show that their business is compliant with respect to many different boundaries. The activity of compliance checking is commonly referred to as auditing. As information systems supporting the organization’s business record their usage, process mining

Flexture plate motion-transfer mechanism, beam-splitter assembly, and interferometer incorporating the same

Energy Technology Data Exchange (ETDEWEB)

Carangelo, Robert M. (Glastonbury, CT); Dettori, Mark D. (Farmington, CT); Grigely, Lawrence J. (South Windsor, CT); Murray, Terence C. (Winchester, MA); Solomon, Peter R. (West Hartford, CT); Van Dine, C. Peter (Bolton, CT); Wright, David D. (Vershire, VT)

1996-01-01

A multiplicity of one-piece flexure plates are assembled in pairs to provide a support system on which a retroreflector may be mounted for reciprocal motion. Combined with balance bodies, the flexure plates provide a support system having portions that are dynamically and statically balanced with one another, irrespective of orientation, so as to thereby immunize the unit against extraneous forces. The motion transfer assembly is especially adapted for use to support a moving retroreflector in a two-arm interferometer that may further include a beamsplitter assembly constructed from a one-piece, integrally formed body, the body having convergent, optically flat planar surfaces of specular reflectance, and means for adjustably mounting a beamsplitter therein. The spectrometer is of modular construction, and employs an integrated clocking sub-assembly as well as a light-weight voice-coil motor.

Magnetic self-assembly of small parts

Science.gov (United States)

Shetye, Sheetal B.

Modern society's propensity for miniaturized end-user products is compelling electronic manufacturers to assemble and package different micro-scale, multi-technology components in more efficient and cost-effective manners. As the size of the components gets smaller, issues such as part sticking and alignment precision create challenges that slow the throughput of conventional robotic pick-n-place systems. As an alternative, various self-assembly approaches have been proposed to manipulate micro to millimeter scale components in a parallel fashion without human or robotic intervention. In this dissertation, magnetic self-assembly (MSA) is demonstrated as a highly efficient, completely parallel process for assembly of millimeter scale components. MSA is achieved by integrating permanent micromagnets onto component bonding surfaces using wafer-level microfabrication processes. Embedded bonded powder methods are used for fabrication of the magnets. The magnets are then magnetized using pulse magnetization methods, and the wafers are then singulated to form individual components. When the components are randomly mixed together, self-assembly occurs when the intermagnetic forces overcome the mixing forces. Analytical and finite element methods (FEM) are used to study the force interactions between the micromagnets. The multifunctional aspects of MSA are presented through demonstration of part-to-part and part-to-substrate assembly of 1 mm x 1mm x 0.5 mm silicon components. Part-to-part assembly is demonstrated by batch assembly of free-floating parts in a liquid environment with the assembly yield of different magnetic patterns varying from 88% to 90% in 20 s. Part-to-substrate assembly is demonstrated by assembling an ordered array onto a fixed substrate in a dry environment with the assembly yield varying from 86% to 99%. In both cases, diverse magnetic shapes/patterns are used to control the alignment and angular orientation of the components. A mathematical model is

Neutron data testing for plutonium isotopes in experiments at fast critical assemblies

International Nuclear Information System (INIS)

Bednyakov, S.M.; Dulin, V.A.; Manturov, G.N.; Mozhaev, V.K.; Semenov, M.Yu.; Tsibulya, A.M.

1996-01-01

Experimental results on checking neutron data, obtained at the fast critical assemblies, are presented. They constitute sufficiently large collection of data making it possible to test nuclear neutron constants of plutonium isotopes for the new system of group constants BNAB-93. The work contains comparison of the measurement results on average fission cross section ratios and reactivity coefficients ratios for 239,240,241 Pu (to 235 U) with calculational data, obtained on the basis of the new testing system of the BNAB-93 group constants system. 14 refs., 6 figs

Get Your Kids Moving and Check Some Chores off Your List

Science.gov (United States)

... Check Recipe Certification Program Nutrition Requirements Heart-Check Professional Resources Contact the Heart-Check Certification Program Simple Cooking and Recipes Dining Out Choosing a Restaurant Deciphering ...

Micro-‘‘factory’’ for self-assembled peptide nanostructures

DEFF Research Database (Denmark)

Castillo, Jaime; Rodriguez-Trujíllo, Romén; Gauthier, Sébastian

2011-01-01

This study describes an integrated micro ‘‘factory’’ for the preparation of biological self-assembled peptide nanotubes and nanoparticles on a polymer chip, yielding controlled growth conditions. Self-assembled peptides constitute attractive building blocks for the fabrication of biological...... nanostructures due to the mild conditions of their synthesis process. This biological material can form nanostructures in a rapid way and the synthesis method is less expensive as compared to that of carbon nanotubes or silicon nanowires. The present article thus reports on the on-chip fabrication of self-assembled...

Consistency Checking of Web Service Contracts

DEFF Research Database (Denmark)

Cambronero, M. Emilia; Okika, Joseph C.; Ravn, Anders Peter

2008-01-01

Behavioural properties are analyzed for web service contracts formulated in Business Process Execution Language (BPEL) and Choreography Description Language (CDL). The key result reported is an automated technique to check consistency between protocol aspects of the contracts. The contracts...... are abstracted to (timed) automata and from there a simulation is set up, which is checked using automated tools for analyzing networks of finite state processes. Here we use the Concurrency Work Bench. The proposed techniques are illustrated with a case study that include otherwise difficult to analyze fault...

The upgrade of integrity analysis module and the mechanical behavior evaluation for the assembly duct

Energy Technology Data Exchange (ETDEWEB)

Lee, Byoung Oon; Lee, Dong Uk; Kim, Young Il [Korea Atomic Energy Research Institute, Taejeon (Korea)

2002-05-01

The high neutron fluxes and operating temperatures associated with KALIMER are inducing the important radiation damage phenomena, which can cause significant dimensional changes in the core components of the reactor.The thermo-mechanical analysis of the assembly ducts for KALIMER are mainly performed to evaluate the following items.1) change of reactivity. 2) force at pads on core assemblies. 3) withdrawal force at refueling. 4) loading and refueling deviation of assembly ducts. 5) bowing modes for control assembly. In this report, the model for the evaluation of reactivity change as well as the refueling model and the withdrawl force model are upgraded. And the reactivity change is considered as the most important parameter among the above items. Therefore, the sensitivity analyses mainly associated with reactivity change are carried out. As the results, the pad gap between the assembly ducts preliminary driven for keeping the (-) reactivity change. 9 refs., 24 figs., 2 tabs. (Author)

Architecturing hierarchical function layers on self-assembled viral templates as 3D nano-array electrodes for integrated Li-ion microbatteries.

Science.gov (United States)

Liu, Yihang; Zhang, Wei; Zhu, Yujie; Luo, Yanting; Xu, Yunhua; Brown, Adam; Culver, James N; Lundgren, Cynthia A; Xu, Kang; Wang, Yuan; Wang, Chunsheng

2013-01-09

This work enables an elegant bottom-up solution to engineer 3D microbattery arrays as integral power sources for microelectronics. Thus, multilayers of functional materials were hierarchically architectured over tobacco mosaic virus (TMV) templates that were genetically modified to self-assemble in a vertical manner on current-collectors, so that optimum power and energy densities accompanied with excellent cycle-life could be achieved on a minimum footprint. The resultant microbattery based on self-aligned LiFePO(4) nanoforests of shell-core-shell structure, with precise arrangement of various auxiliary material layers including a central nanometric metal core as direct electronic pathway to current collector, delivers excellent energy density and stable cycling stability only rivaled by the best Li-ion batteries of conventional configurations, while providing rate performance per foot-print and on-site manufacturability unavailable from the latter. This approach could open a new avenue for microelectromechanical systems (MEMS) applications, which would significantly benefit from the concept that electrochemically active components be directly engineered and fabricated as an integral part of the integrated circuit (IC).

Integration Process for the Habitat Demonstration Unit

Science.gov (United States)

Gill, Tracy; Merbitz, Jerad; Kennedy, Kriss; Tri, Terry; Howe, A. Scott

2010-01-01

The Habitat Demonstration Unit (HDU) is an experimental exploration habitat technology and architecture test platform designed for analog demonstration activities The HDU project has required a team to integrate a variety of contributions from NASA centers and outside collaborators and poses a challenge in integrating these disparate efforts into a cohesive architecture To complete the development of the HDU from conception in June 2009 to rollout for operations in July 2010, a cohesive integration strategy has been developed to integrate the various systems of HDU and the payloads, such as the Geology Lab, that those systems will support The utilization of interface design standards and uniquely tailored reviews have allowed for an accelerated design process Scheduled activities include early fit-checks and the utilization of a Habitat avionics test bed prior to equipment installation into HDU A coordinated effort to utilize modeling and simulation systems has aided in design and integration concept development Modeling tools have been effective in hardware systems layout, cable routing and length estimation, and human factors analysis Decision processes on the shell development including the assembly sequence and the transportation have been fleshed out early on HDU to maximize the efficiency of both integration and field operations Incremental test operations leading up to an integrated systems test allows for an orderly systems test program The HDU will begin its journey as an emulation of a Pressurized Excursion Module (PEM) for 2010 field testing and then may evolve to a Pressurized Core Module (PCM) for 2011 and later field tests, depending on agency architecture decisions The HDU deployment will vary slightly from current lunar architecture plans to include developmental hardware and software items and additional systems called opportunities for technology demonstration One of the HDU challenges has been designing to be prepared for the integration of

Tritium breeding experiments in a fusion blanket assembly using a low-intensity neutron generator

International Nuclear Information System (INIS)

Dalton, A.W.; Woodley, H.J.; McGregor, B.J.

1987-01-01

Experiments have been carried out to determine the accuracy with which tritium production rates (TPRs) can be measured in a fusion blanket assembly of non-spherical geometry by a non-central low intensity D-T neutron source (2x10 10 neutrons per second). The tritium production was determined for samples of lithium carbonate containing high enrichments of 6 Li(96%) and 7 Li(99.9%). The measured data were used to check the accuracy with which the TPRs could be numerically predicted using current nuclear data and calculational methods. The numerical predictions from tritium production from the 7 Li samples agreed within the experimental errors of the measurements, but 6 Li measurements which differ by more than 20 per cent from the predicted values were observed in the lower half of the assembly

Checking BEBC superconducting magnet

CERN Multimedia

CERN PhotoLab

1974-01-01

The superconducting coils of the magnet for the 3.7 m Big European Bubble Chamber (BEBC) had to be checked, see Annual Report 1974, p. 60. The photo shows a dismantled pancake. By December 1974 the magnet reached again the field design value of 3.5 T.

Self-assembly as a design tool for the integration of photonic structures into excitonic solar cells

KAUST Repository

Guldin, S.; Docampo, P.; Hü ttner, S.; Kohn, P.; Stefik, M.; Snaith, H. J.; Wiesner, U.; Steiner, U.

2011-01-01

) into dye-sensitized solar cells (DSCs). In both cases, the self-assembly of soft matter plays a key role in the fabrication process of the TiO2 electrode. One approach relies on a combination of colloidal self-assembly and the self-assembly of block

Quality checking of radioactive and hazardous waste

International Nuclear Information System (INIS)

Billington, D.M.; Burgoyne, S.M.J.; Dale, C.J.

1992-01-01

This report describes the work of the HMIP Waste Quality Checking Laboratory (WQCL) for the period September 1989 -August 1991. The WQCL has conducted research and development of procedures for the receipt, sampling and analysis of low level solid radioactive waste (LLW), intermediate level radioactive waste (ILW) and hazardous chemical waste (HW). Operational facilities have been commissioned for quality checking both LLW and HW. Waste quality checking has been completed on LLW packages seized from the UK waste disposal route by HMIP Inspectors. Packages have ranged in size from the 200 litre steel drum to half-height ISO freight container. Development work was continued on methods of sample extraction and radio-chemical analysis for cement encapsulated ILW in the form of magnox, graphite and stainless steel. This work was undertaken on non-radioactive simulants. (author)

Model Checking Markov Reward Models with Impulse Rewards

NARCIS (Netherlands)

Cloth, Lucia; Katoen, Joost-Pieter; Khattri, Maneesh; Pulungan, Reza; Bondavalli, Andrea; Haverkort, Boudewijn; Tang, Dong

This paper considers model checking of Markov reward models (MRMs), continuous-time Markov chains with state rewards as well as impulse rewards. The reward extension of the logic CSL (Continuous Stochastic Logic) is interpreted over such MRMs, and two numerical algorithms are provided to check the

Checking Consistency of Pedigree Information is NP-complete

DEFF Research Database (Denmark)

Aceto, Luca; Hansen, Jens A.; Ingolfsdottir, Anna

Consistency checking is a fundamental computational problem in genetics. Given a pedigree and information on the genotypes of some of the individuals in it, the aim of consistency checking is to determine whether these data are consistent with the classic Mendelian laws of inheritance. This probl...

Strategic Planning through Model Checking of ATL Formulae

NARCIS (Netherlands)

Jamroga, W.J.; Rutkowski, L.; Siekmann, J.; Tadeusiewicz, R.; Zadeh, L.A.

2004-01-01

Model checking of temporal logic has already been proposed for automatic planning. In this paper, we introduce a simple adaptation of the ATL model checking algorithm that returns a strategy to achieve given goal. We point out that the algorithm generalizes minimaxing, and that ATL models generalize

First experiences with the LHC BLM sanity checks

CERN Document Server

Emery, J; Effinger, E; Nordt, A; Sapinski, M G; Zamantzas, C

2010-01-01

The reliability concerns have driven the design of the Large Hardron Collider (LHC) Beam Loss Monitoring (BLM) system from the early stage of the studies up to the present commissioning and the latest development of diagnostic tools. To protect the system against non-conformities, new ways of automatic checking have been developed and implemented. These checks are regularly and systematically executed by the LHC operation team to ensure that the system status is after each test "as good as new". The sanity checks are part of this strategy. They are testing the electrical part of the detectors (ionisation chamber or secondary emission detector), their cable connections to the front-end electronics, further connections to the back-end electronics and their ability to request a beam abort. During the installation and in the early commissioning phase, these checks have shown their ability to find also non-conformities caused by unexpected failure event scenarios. In every day operation, a non-conformity discovere...

Review and analysis of check valve failure data

International Nuclear Information System (INIS)

Todd, M.D.; Casada, D.A.

1992-01-01

Check valve operating problems in recent years have resulted in significant operating transients, increased cost and decreased system availability. There has been, in response, additional attention given to check valves by utilities, as well as the US Nuclear Regulatory Commission and the American Society of Mechanical Engineers Operation and Maintenance Committee. All these organizations have the fundamental goal of ensuring reliable operation of check valves. A key ingredient to an engineering-oriented reliability improvement effort is a thorough understanding of relevant historical experience. Oak Ridge National Laboratory is currently conducting a detailed review of historical failure data available through the Institute of Nuclear Power Operation's Nuclear Plant Reliability Data System. The focus of the review is on check valve failures that have involved significant degradation of the valve internal parts. A variety of parameters are being considered during the review, including size, age, system of service, method of failure discovery, the affected valve parts, attributed causes, and corrective actions

Integrated system for automated financial document processing

Science.gov (United States)

Hassanein, Khaled S.; Wesolkowski, Slawo; Higgins, Ray; Crabtree, Ralph; Peng, Antai

1997-02-01

A system was developed that integrates intelligent document analysis with multiple character/numeral recognition engines in order to achieve high accuracy automated financial document processing. In this system, images are accepted in both their grayscale and binary formats. A document analysis module starts by extracting essential features from the document to help identify its type (e.g. personal check, business check, etc.). These features are also utilized to conduct a full analysis of the image to determine the location of interesting zones such as the courtesy amount and the legal amount. These fields are then made available to several recognition knowledge sources such as courtesy amount recognition engines and legal amount recognition engines through a blackboard architecture. This architecture allows all the available knowledge sources to contribute incrementally and opportunistically to the solution of the given recognition query. Performance results on a test set of machine printed business checks using the integrated system are also reported.

Safety and Availability Checking for User Authorization Queries in RBAC

Directory of Open Access Journals (Sweden)

Jian-feng Lu

2012-09-01

Full Text Available This paper introduces the notion of safety and availability checking for user authorization query processing, and develop a recursive algorithm use the ideas from backtracking-based search techniques to search for the optimal solution. For the availability checking, we introduce the notion of max activatable set (MAS, and show formally how MAS can be determined in a hybrid role hierarchy. For the safety checking, we give a formal definition of dynamic separation-of-duty (DSoD policies, and show how to reduce the safety checking for DSoD to a SAT instance.

The Activity Check of Brachytherapy Isotope

International Nuclear Information System (INIS)

Kim, Gun Oh; Lee, Byung Koo; Kwon, Young Ho

2004-01-01

An isotope Ir-192, which is used in brachytherapy depends on import in whole quantities. There are a few ways for its activity. measurement using Welltype chamber or the way to rely on authentic decay table of manufacturer. In-air dosimetry using Farmer Chamber, etc. In this paper, let me introduce the way using Farmer chamber which is easier and simple. With the Farmer chamber and source calibration jig, take a measurement the activity of an isotope Ir-192 and compare the value with the value from decay table of manufacturer and check the activity of source. The result of measurement, compared the value from decay table, by ±2.1. (which belongs to recommendable value for AAPM ±5% as difference of error range). It is possible to use on clinical medicine. With the increase in use of brachytherapy, the increase of import is essential. And an accurate activity check of source is compulsory. For the activity check of source, it was possible to use Farmer chamber and source calibration jig without additional purchase of Well type chamber.

Accident Analysis of High Density Storage Rack for Fresh Fuel Assemblies

International Nuclear Information System (INIS)

Jang, K. J.; Lee, M. J.; Jin, H. U.; Park, J. H.; Shin, S. Y.

2009-01-01

Recently KONES and KNF have developed the so called suspension-type High Density Storage Rack (HDSR) for fresh fuel assemblies. The USNRC OT position paper specifies that the design of the rack must ensure the functional integrity of the fuel racks under all credible fuel assembly drop events. In this context the functional integrity means the criticality safety. That is to say, the drop events must not bring any danger to the criticality safety of HDSR. This paper shows the results of the analysis carried out to demonstrate the regulatory compliance of the proposed racks under postulated accidental drop events

The Focal Plane Assembly for the Athena X-Ray Integral Field Unit Instrument

Science.gov (United States)

Jackson, B. D.; Van Weers, H.; van der Kuur, J.; den Hartog, R.; Akamatsu, H.; Argan, A.; Bandler, S. R.; Barbera, M.; Barret, D.; Bruijn, M. P.;

31 CFR 211.1 - Withholding delivery of checks.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 2 2010-07-01 2010-07-01 false Withholding delivery of checks. 211.1 Section 211.1 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) FISCAL SERVICE, DEPARTMENT OF THE TREASURY FINANCIAL MANAGEMENT SERVICE DELIVERY OF CHECKS AND WARRANTS TO...

Stress analysis of fuel assemblies under seismic load

International Nuclear Information System (INIS)

Kiselev, A.; Krutko, E.; Kiselev, I.; Tutnov, A.

2011-01-01

One of the important parts of fuel assemblies (FA) safety validation is their strength estimation under the dynamic loads, such as the vibration effects caused by the work of reactor units and the seismic exposure of an earthquake, leading to extreme inertia loads on all elements of the NPP. Taking into account structural features of FA and a very large mass, the exposure of seismic loads can lead to significant deformation of fuel assemblies. It is necessary to assess the magnitude of the force interaction between the FA in case of an earthquake to estimate the strength and performance of fuel assemblies. It is also necessary to compute FA bending forms and maximum values for further RPS control rods inserting time estimation, and for disassembly possibility justification of the core and individual FA after the earthquake. The problem of WWER-1000 core dynamic behavior modeling with TVS-2M fuel assemblies under the seismic loads exposure using the finite element method is described. Each fuel assembly is represented by equivalent rod finite element model. The reactor core is simulated by 163 fuel assemblies in accordance with the reactor core construction. Stiffness characteristics of fuel assemblies are determined on the results of a series of static and dynamic TVS-2M FA field tests. The special algorithm was developed to consider the fuel rod slippage effect during deformation. The special contact elements are introduced into the model of the core to take into account the interaction of fuel assemblies with their neighbors and with core barrel. Solution of the dynamic equilibrium equations system of finite element model is implemented by direct integration using the explicit scheme. Parallel algorithms for numerical integration on multiprocessor computers with graphics processing unit is developed to improve the efficiency of calculations. Values of nodes displacement in finite element model of reactor core as a function of seismic excitation time are obtained

Multi-Valued Modal Fixed Point Logics for Model Checking

Science.gov (United States)

Nishizawa, Koki

In this paper, I will show how multi-valued logics are used for model checking. Model checking is an automatic technique to analyze correctness of hardware and software systems. A model checker is based on a temporal logic or a modal fixed point logic. That is to say, a system to be checked is formalized as a Kripke model, a property to be satisfied by the system is formalized as a temporal formula or a modal formula, and the model checker checks that the Kripke model satisfies the formula. Although most existing model checkers are based on 2-valued logics, recently new attempts have been made to extend the underlying logics of model checkers to multi-valued logics. I will summarize these new results.

Estimated emission reductions from California's enhanced Smog Check program.

Science.gov (United States)

Singer, Brett C; Wenzel, Thomas P

2003-06-01

The U.S. Environmental Protection Agency requires that states evaluate the effectiveness of their vehicle emissions inspection and maintenance (I/M) programs. This study demonstrates an evaluation approach that estimates mass emission reductions over time and includes the effect of I/M on vehicle deterioration. It includes a quantitative assessment of benefits from pre-inspection maintenance and repairs and accounts for the selection bias effect that occurs when intermittent high emitters are tested. We report estimates of one-cycle emission benefits of California's Enhanced Smog Check program, ca. 1999. Program benefits equivalent to metric tons per day of prevented emissions were calculated with a "bottom-up" approach that combined average per vehicle reductions in mass emission rates (g/gal) with average per vehicle activity, resolved by model year. Accelerated simulation mode test data from the statewide vehicle information database (VID) and from roadside Smog Check testing were used to determine 2-yr emission profiles of vehicles passing through Smog Check and infer emission profiles that would occur without Smog Check. The number of vehicles participating in Smog Check was also determined from the VID. We estimate that in 1999 Smog Check reduced tailpipe emissions of HC, CO, and NO(x) by 97, 1690, and 81 t/d, respectively. These correspond to 26, 34, and 14% of the HC, CO, and NO(x) that would have been emitted by vehicles in the absence of Smog Check. These estimates are highly sensitive to assumptions about vehicle deterioration in the absence of Smog Check. Considering the estimated uncertainty in these assumptions yields a range for calculated benefits: 46-128 t/d of HC, 860-2200 t/d of CO, and 60-91 t/d of NO(x). Repair of vehicles that failed an initial, official Smog Check appears to be the most important mechanism of emission reductions, but pre-inspection maintenance and repair also contributed substantially. Benefits from removal of nonpassing

Turbomachinery Design Quality Checks to Avoid Friction Induced Structural Failure

Science.gov (United States)

Moore, Jerry H.

1999-01-01

A unique configuration of the P&W SSME Alternate Fuel Turbopump turbine disk/blade assembly, combined with a severe thermal environment, resulted in several structural anomalies that were driven by frictional contact forces. Understanding the mechanics of these problems provides new quality checks for future turbo machinery designs. During development testing in 1997 of the SSME alternate fuel turbopump at Stennis Space Center, several potentially serious problems surfaced with the turbine disk/blade assembly that had not been experienced in extensive earlier testing. Changes to the operational thermal environment were noted based on analytical prediction of modifications that affected performance and on stationary thermal measurements adjacent to the rotor assembly. A detailed structural investigation was required to reveal the mechanism of distress induced by the change. The turbine disk experienced cracking in several locations due to increased thermal gradient induced stress during start and shutdown transients. This was easily predictable using standard analysis procedures and expected once the thermal environment was characterized. What was not expected was the curling of a piston ring used for blade axial retention in the disk, indentation of the axial face of the blade attachment by a spacer separating the first and second stage blades, and most significantly, galling and cracking of the blade root attachment that could have resulted in blade release. Past experience, in gas turbine environments, set a precedent of never relying on friction for help and to evaluate it only in specific instances where it was obvious that it would degrade capability. In each of the three cases above, friction proved to be a determining factor that pushed the components into an unsatisfactory mode of operation. The higher than expected temperatures and rapid thermal transients combined with friction to move beyond past experience. The turbine disk/blade assembly configuration

305 Building 2 ton bridge crane and monorail assembly analysis

International Nuclear Information System (INIS)

Axup, M.D.

1995-12-01

The analyses in the appendix of this document evaluate the integrity of the existing bridge crane structure, as depicted on drawing H-3-34292, for a bridge crane and monorail assembly with a load rating of 2 tons. This bridge crane and monorail assembly is a modification of a 1 1/2 ton rated manipulator bridge crane which originally existed in the 305 building

Delivery quality assurance with ArcCHECK

International Nuclear Information System (INIS)

Neilson, Christopher; Klein, Michael; Barnett, Rob; Yartsev, Slav

2013-01-01

Radiation therapy requires delivery quality assurance (DQA) to ensure that treatment is accurate and closely follows the plan. We report our experience with the ArcCHECK phantom and investigate its potential optimization for the DQA process. One-hundred seventy DQA plans from 84 patients were studied. Plans were classified into 2 groups: those with the target situated on the diodes of the ArcCHECK (D plans) and those with the target situated at the center (C plans). Gamma pass rates for 8 target sites were examined. The parameters used to analyze the data included 3%/3 mm with the Van Dyk percent difference criteria (VD) on, 3%/3 mm with the VD off, 2%/2 mm with the VD on, and x/3 mm with the VD on and the percentage dosimetric agreement “x” for diode plans adjusted. D plans typically displayed maximum planned dose (MPD) on the cylindrical surface containing ArcCHECK diodes than center plans, resulting in inflated gamma pass rates. When this was taken into account by adjusting the percentage dosimetric agreement, C plans outperformed D plans by an average of 3.5%. ArcCHECK can streamline the DQA process, consuming less time and resources than radiographic films. It is unnecessary to generate 2 DQA plans for each patient; a single center plan will suffice. Six of 8 target sites consistently displayed pass rates well within our acceptance criteria; the lesser performance of head and neck and spinal sites can be attributed to marginally lower doses and increased high gradient of plans

Assessment of diagnostic methods for determining degradation of check valves

International Nuclear Information System (INIS)

Haynes, H.D.; Farmer, W.S.

1992-01-01

The Oak Ridge National Laboratory (ORNL) has carried out a comprehensive aging assessment of check valves in support of the Nuclear Plant Aging Research (NPAR) program. This paper provides a summary of the ORNL check valve aging assessment with emphasis on the identification, evaluation, and application of check valve monitoring methods and techniques. Several check valve monitoring methods are described and compared. These methods include: acoustic emission monitoring, ultrasonic inspection, magnetic flux signature analysis (MFSA), external magnetics. These diagnostic technologies were shown to be useful in determining check valve condition (e.g., disc position, disc motion, and seat leakage), although none of the methods was by itself, successful in monitoring all three condition indicators. The combination of acoustic emission with either ultrasonics or one of the magnetic technologies, however, yields a monitoring system that succeeds in providing the sensitivity to detect all major check valve operating conditions. Other areas covered in the paper include descriptions of relevant regulatory issues, utility group activities, and interactions ORNL has had with outside organizations for the purpose of disseminating research results

Radioactive check sources for alpha and beta sensitive radiological instrumentation

International Nuclear Information System (INIS)

Barnett, J.M.; Kane, J.E. II.

1994-06-01

Since 1991, the Westinghouse Hanford Company has examined the construction and use of alpha and beta radioactive check sources for calibrating instruments and for performing response checks of instruments used for operational and environmental radiation detection. The purpose of using a radioactive check source is to characterize the response of a radiation monitoring instrument in the presence of radioactivity. To accurately calibrate the instrument and check its response, the check source used must emulate as closely as possible the actual physical and isotopic conditions being monitored. The isotope employed and the physical methods used to fabricate the check source (among other factors) determine instrument response. Although information from applicable national and international standards, journal articles, books, and government documents was considered, empirical data collected is most valuable when considering the type of source to use for a particular application. This paper presents source construction methods, use considerations, and standard recommendations. The results of a Hanford Site evaluation of several types of alpha and beta sources are also given

Current status of the post boiling transition research in Japan. Integrity evaluation of nuclear fuel assemblies after boiling transition and development of rewetting correlations

International Nuclear Information System (INIS)

Hara, Takashi; Mizokami, Shinya; Kudo, Yoshiro; Komura, Seiichi; Nagata, Yoshifumi; Morooka, Shinichi

2003-01-01

Development of rewetting correlation formula was the key to predict fuel-cladding temperature after Boiling Transition (BT). Japanese BWR utilities and vendors performed some tests of rewetting and made two rewetting correlation formulas. The effect on fuel integrity after BT depends on temperature of fuel rod and time of dryout. Main cause of losing fuel integrity during BWR's Anticipated Operational Occurrences (AOO) after BT is embrittlement of the claddings due to oxidation. Ballooning of fuel rod is excepted because its pressure boundary isn't broken. In Japan, the Standards Committee of Atomic Energy Society of Japan (AESJ) is making post BT standard. This standard provides guidelines based on the latest knowledge to judge fuel integrity in case of BT and the validity of reusing the fuel assembly that experienced BT in BWRs. (author)

Double checking medicines: defence against error or contributory factor?

Science.gov (United States)

Armitage, Gerry

2008-08-01

The double checking of medicines in health care is a contestable procedure. It occupies an obvious position in health care practice and is understood to be an effective defence against medication error but the process is variable and the outcomes have not been exposed to testing. This paper presents an appraisal of the process using data from part of a larger study on the contributory factors in medication errors and their reporting. Previous research studies are reviewed; data are analysed from a review of 991 drug error reports and a subsequent series of 40 in-depth interviews with health professionals in an acute hospital in northern England. The incident reports showed that errors occurred despite double checking but that action taken did not appear to investigate the checking process. Most interview participants (34) talked extensively about double checking but believed the process to be inconsistent. Four key categories were apparent: deference to authority, reduction of responsibility, automatic processing and lack of time. Solutions to the problems were also offered, which are discussed with several recommendations. Double checking medicines should be a selective and systematic procedure informed by key principles and encompassing certain behaviours. Psychological research may be instructive in reducing checking errors but the aviation industry may also have a part to play in increasing error wisdom and reducing risk.

Integral test of International Reactor Dosimetry and Fusion File with Li{sub 2}O assembly and DT neutron source at JAEA/FNS

Energy Technology Data Exchange (ETDEWEB)

Sato, Satoshi, E-mail: sato.satoshi92@jaea.go.jp [Japan Atomic Energy Agency, Tokai-mura, Naka-gun, Ibaraki-ken (Japan); Kwon, Saerom; Ohta, Masayuki [Japan Atomic Energy Agency, Tokai-mura, Naka-gun, Ibaraki-ken (Japan); Ochiai, Kentaro [Japan Atomic Energy Agency, Rokkasho-mura, Kamikita-gun, Aomori-ken (Japan); Konno, Chikara [Japan Atomic Energy Agency, Tokai-mura, Naka-gun, Ibaraki-ken (Japan)

2016-11-01

In order to validate a new library of dosimetry cross section data, International Reactor Dosimetry and Fusion File release 1.0 (IRDFF 1.0), not only for DT neutrons but also for neutrons with energy of less than 14 MeV, we perform an integral test with a Li{sub 2}O rectangular assembly of 60.7 cm in thickness and a DT neutron source at JAEA/FNS. We place a lot of activation foils at depths of 10.1 cm and 30.4 cm for measurements of dosimetry reaction rates in small space along the central axis in the assembly, measure decay gamma-rays from the activation foils with high-purity Ge detectors after the DT neutron irradiation by the foil activation technique, and deduce a variety of dosimetry reaction rates. We calculate the reaction rates by using a Monte Carlo code MCNP5-1.40 and the nuclear data library ENDF/B-VII.1 with the IRDFF-v.1.05 as the response functions for the dosimetry reactions. The calculation results generally show good agreements with the measured ones, and it can be confirmed that most of the data in IRDFF-v.1.05 are valid for the neutron field in the Li{sub 2}O assembly with the DT neutrons.

Mounting Systems for Structural Members, Fastening Assemblies Thereof, and Vibration Isolation Systems Including the Same

Science.gov (United States)

Young, Ken (Inventor); Hindle, Timothy (Inventor); Barber, Tim Daniel (Inventor)

2016-01-01

Mounting systems for structural members, fastening assemblies thereof, and vibration isolation systems including the same are provided. Mounting systems comprise a pair of mounting brackets, each clamped against a fastening assembly forming a mounting assembly. Fastening assemblies comprise a spherical rod end comprising a spherical member having a through opening and an integrally threaded shaft, first and second seating members on opposite sides of the spherical member and each having a through opening that is substantially coaxial with the spherical member through opening, and a partially threaded fastener that threadably engages each mounting bracket forming the mounting assembly. Structural members have axial end portions, each releasably coupled to a mounting bracket by the integrally threaded shaft. Axial end portions are threaded in opposite directions for permitting structural member rotation to adjust a length thereof to a substantially zero strain position. Structural members may be vibration isolator struts in vibration isolation systems.

Fault Tree Analysis with Temporal Gates and Model Checking Technique for Qualitative System Safety Analysis

International Nuclear Information System (INIS)

Koh, Kwang Yong; Seong, Poong Hyun

2010-01-01

Fault tree analysis (FTA) has suffered from several drawbacks such that it uses only static gates and hence can not capture dynamic behaviors of the complex system precisely, and it is in lack of rigorous semantics, and reasoning process which is to check whether basic events really cause top events is done manually and hence very labor-intensive and time-consuming for the complex systems while it has been one of the most widely used safety analysis technique in nuclear industry. Although several attempts have been made to overcome this problem, they can not still do absolute or actual time modeling because they adapt relative time concept and can capture only sequential behaviors of the system. In this work, to resolve the problems, FTA and model checking are integrated to provide formal, automated and qualitative assistance to informal and/or quantitative safety analysis. Our approach proposes to build a formal model of the system together with fault trees. We introduce several temporal gates based on timed computational tree logic (TCTL) to capture absolute time behaviors of the system and to give concrete semantics to fault tree gates to reduce errors during the analysis, and use model checking technique to automate the reasoning process of FTA

LFI Radiometric Chain Assembly (RCA) data handling ``Rachel''

Science.gov (United States)

Malaspina, M.; Franceschi, E.; Battaglia, P.; Binko, P.; Butler, R. C.; D'Arcangelo, O.; Fogliani, S.; Frailis, M.; Franceschet, C.; Galeotta, S.; Gasparo, F.; Gregorio, A.; Lapolla, M.; Leonardi, R.; Maggio, G.; Mandolesi, N.; Manzato, P.; Maris, M.; Meharga, M.; Meinhold, P.; Morisset, N.; Pasian, F.; Perrotta, F.; Rohlfs, R.; Sandri, M.; Tomasi, M.; Türler, M.; Zacchei, A.; Zonca, A.

2009-12-01

Planck's Low Frequency Instrument is an array of 22 pseudo-correlation radiometers at 30, 44, and 70 GHz. Before integrating the overall array assembly, a first set of tests has been performed for each radiometer chain assembly (RCA), consisting of two radiometers. In this paper, we describe Rachel, a software application which has been purposely developed and used during the RCA test campaign to carry out both near-realtime on-line data analysis and data storage (in FITS format) of the raw output from the radiometric chains.

LFI Radiometric Chain Assembly (RCA) data handling 'Rachel'

International Nuclear Information System (INIS)

Malaspina, M; Franceschi, E; Butler, R C; Mandolesi, N; Battaglia, P; Franceschet, C; Lapolla, M; Binko, P; Meharga, M; D'Arcangelo, O; Fogliani, S; Frailis, M; Galeotta, S; Gasparo, F; Maggio, G; Manzato, P; Maris, M; Gregorio, A; Leonardi, R; Meinhold, P

2009-01-01

Planck's Low Frequency Instrument is an array of 22 pseudo-correlation radiometers at 30, 44, and 70 GHz. Before integrating the overall array assembly, a first set of tests has been performed for each radiometer chain assembly (RCA), consisting of two radiometers. In this paper, we describe Rachel, a software application which has been purposely developed and used during the RCA test campaign to carry out both near-realtime on-line data analysis and data storage (in FITS format) of the raw output from the radiometric chains.

Structure and experimental program for SNEAK 12 - an assembly for fast breeder safety experiments

International Nuclear Information System (INIS)

Helm, F.

1979-01-01

The critical assembly SNEAK 12 and its foreseen experimental program have the main purpose to check the validity of neutron physics calculational methods used in the analysis of accidental situations of fast breeder reactors. In the investigation of accidental courses configurations have to be considered, which are caused by assembly deformation and meltdown and which are characterized by irregular fuel and structural material arrangements with cavities and empty channels. The reactivity differences between the unperturbed core and a series of perturbed configurations have to be determined. The individual configurations have to be chosen in such a way, that the calculational methods for the different aspects of the accident sequence (formation of cavities and channels, relocation of fissile and fertile material and steel) can be tested one by one. Two different cores are foreseen: SNEAK 12A as a one-zone core with enriched uranium fuel and SNEAK 12B with a central test zone with plutonium-uranium mixed-oxide fuel surrounded by a driver zone of enriched uranium. The report describes these cores and their assemblies, and the experimental program is outlined

Self-assembly from milli- to nanoscales: methods and applications

International Nuclear Information System (INIS)

Mastrangeli, M; Celis, J-P; Abbasi, S; Varel, C; Böhringer, K F; Van Hoof, C

2009-01-01

The design and fabrication techniques for microelectromechanical systems (MEMS) and nanodevices are progressing rapidly. However, due to material and process flow incompatibilities in the fabrication of sensors, actuators and electronic circuitry, a final packaging step is often necessary to integrate all components of a heterogeneous microsystem on a common substrate. Robotic pick-and-place, although accurate and reliable at larger scales, is a serial process that downscales unfavorably due to stiction problems, fragility and sheer number of components. Self-assembly, on the other hand, is parallel and can be used for device sizes ranging from millimeters to nanometers. In this review, the state-of-the-art in methods and applications for self-assembly is reviewed. Methods for assembling three-dimensional (3D) MEMS structures out of two-dimensional (2D) ones are described. The use of capillary forces for folding 2D plates into 3D structures, as well as assembling parts onto a common substrate or aggregating parts to each other into 2D or 3D structures, is discussed. Shape matching and guided assembly by magnetic forces and electric fields are also reviewed. Finally, colloidal self-assembly and DNA-based self-assembly, mainly used at the nanoscale, are surveyed, and aspects of theoretical modeling of stochastic assembly processes are discussed. (topical review)

Body Covering and Body Image: A Comparison of Veiled and Unveiled Muslim Women, Christian Women, and Atheist Women Regarding Body Checking, Body Dissatisfaction, and Eating Disorder Symptoms.

Science.gov (United States)

Wilhelm, Leonie; Hartmann, Andrea S; Becker, Julia C; Kişi, Melahat; Waldorf, Manuel; Vocks, Silja

2018-02-21

Although Islam is the fastest growing religion worldwide, only few studies have investigated body image in Muslim women, and no study has investigated body checking. Therefore, the present study examined whether body image, body checking, and disordered eating differ between veiled and unveiled Muslim women, Christian women, and atheist women. While the groups did not differ regarding body dissatisfaction, unveiled Muslim women reported more checking than veiled Muslim and Christian women, and higher bulimia scores than Christian. Thus, prevention against eating disorders should integrate all women, irrespective of religious affiliation or veiling, with a particular focus on unveiled Muslim women.

Related Fact Checks: a tool for combating fake news

OpenAIRE

Guha, Sreya

2017-01-01

The emergence of "Fake News" and misinformation via online news and social media has spurred an interest in computational tools to combat this phenomenon. In this paper we present a new "Related Fact Checks" service, which can help a reader critically evaluate an article and make a judgment on its veracity by bringing up fact checks that are relevant to the article. We describe the core technical problems that need to be solved in building a "Related Fact Checks" service, and present results ...

Check-up Measurement (update). Deliverable D5.22

NARCIS (Netherlands)

Holtzer, A.C.G.; Giessen, A.M.D. van der; Djurica, M.

2015-01-01

This deliverable D5.22 presents the GEN6 check-up measurement. It describes the most prominent outcomes of the GEN6 project up to this point in time. The check-up measurement helps to focus the monitoring towards the most relevant achievements of the project, such that an efficient and well-targeted

Treasury Check Verification Query (TCVQ)

Data.gov (United States)

Social Security Administration — The TCVQ system determines the SSN of an individual whose check has been returned to a local field office. The FO is able to request this information via the TCVQ...

Precise Truss Assembly Using Commodity Parts and Low Precision Welding

Science.gov (United States)

Komendera, Erik; Reishus, Dustin; Dorsey, John T.; Doggett, W. R.; Correll, Nikolaus

2014-01-01

Hardware and software design and system integration for an intelligent precision jigging robot (IPJR), which allows high precision assembly using commodity parts and low-precision bonding, is described. Preliminary 2D experiments that are motivated by the problem of assembling space telescope optical benches and very large manipulators on orbit using inexpensive, stock hardware and low-precision welding are also described. An IPJR is a robot that acts as the precise "jigging", holding parts of a local structure assembly site in place, while an external low precision assembly agent cuts and welds members. The prototype presented in this paper allows an assembly agent (for this prototype, a human using only low precision tools), to assemble a 2D truss made of wooden dowels to a precision on the order of millimeters over a span on the order of meters. The analysis of the assembly error and the results of building a square structure and a ring structure are discussed. Options for future work, to extend the IPJR paradigm to building in 3D structures at micron precision are also summarized.

From self-organization to self-assembly: a new materialism?

Science.gov (United States)

Vincent, Bernadette Bensaude

2016-09-01

While self-organization has been an integral part of academic discussions about the distinctive features of living organisms, at least since Immanuel Kant's Critique of Judgement, the term 'self-assembly' has only been used for a few decades as it became a hot research topic with the emergence of nanotechnology. Could it be considered as an attempt at reducing vital organization to a sort of assembly line of molecules? Considering the context of research on self-assembly I argue that the shift of attention from self-organization to self-assembly does not really challenge the boundary between chemistry and biology. Self-assembly was first and foremost investigated in an engineering context as a strategy for manufacturing without human intervention and did not raise new perspectives on the emergence of vital organization itself. However self-assembly implies metaphysical assumptions that this paper tries to disentangle. It first describes the emergence of self-assembly as a research field in the context of materials science and nanotechnology. The second section outlines the metaphysical implications and will emphasize a sharp contrast between the ontology underlying two practices of self-assembly developed under the umbrella of synthetic biology. And unexpectedly, we shall see that chemists are less on the reductionist side than most synthetic biologists. Finally, the third section ventures some reflections on the kind of design involved in self-assembly practices.

Progress Check Module; Basic Electricity and Electronics Individualized Learning System. Progress Check Booklet.

Science.gov (United States)

Bureau of Naval Personnel, Washington, DC.

The Progress Check Booklet is designed to be used by the student working in the programed course to determine if he has mastered the concepts in the course booklets on: electrical current; voltage; resistance; measuring current and voltage in series circuits; relationships of current, voltage, and resistance; parellel circuits; combination…

31 CFR 10.31 - Negotiation of taxpayer checks.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 1 2010-07-01 2010-07-01 false Negotiation of taxpayer checks. 10.31 Section 10.31 Money and Finance: Treasury Office of the Secretary of the Treasury PRACTICE BEFORE THE INTERNAL REVENUE SERVICE Duties and Restrictions Relating to Practice Before the Internal Revenue Service § 10.31 Negotiation of taxpayer checks. ...

Hydrazine-mediated construction of nanocrystal self-assembly materials.

Science.gov (United States)

Zhou, Ding; Liu, Min; Lin, Min; Bu, Xinyuan; Luo, Xintao; Zhang, Hao; Yang, Bai

2014-10-28

Self-assembly is the basic feature of supramolecular chemistry, which permits to integrate and enhance the functionalities of nano-objects. However, the conversion of self-assembled structures to practical materials is still laborious. In this work, on the basis of studying one-pot synthesis, spontaneous assembly, and in situ polymerization of aqueous semiconductor nanocrystals (NCs), NC self-assembly materials are produced and applied to design high performance white light-emitting diode (WLED). In producing self-assembly materials, the additive hydrazine (N2H4) is curial, which acts as the promoter to achieve room-temperature synthesis of aqueous NCs by favoring a reaction-controlled growth, as the polyelectrolyte to weaken inter-NC electrostatic repulsion and therewith facilitate the one-dimensional self-assembly, and in particular as the bifunctional monomers to polymerize with mercapto carboxylic acid-modified NCs via in situ amidation reaction. This strategy is versatile for mercapto carboxylic acid-modified aqueous NCs, for example CdS, CdSe, CdTe, CdSe(x)Te(1-x), and Cd(y)Hg(1-y)Te. Because of the multisite modification with carboxyl, the NCs act as macromonomers, thus producing cross-linked self-assembly materials with excellent thermal, solvent, and photostability. The assembled NCs preserve strong luminescence and avoid unpredictable fluorescent resonance energy transfer, the main problem in design WLED from multiple NC components. These advantages allow the fabrication of NC-based WLED with high color rendering index (86), high luminous efficacy (41 lm/W), and controllable color temperature.

42 CFR 433.40 - Treatment of uncashed or cancelled (voided) Medicaid checks.

Science.gov (United States)

2010-10-01

...) Medicaid checks. 433.40 Section 433.40 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT...) Medicaid checks. (a) Purpose. This section provides the rules to ensure that States refund the Federal...— Cancelled (voided) check means a Medicaid check issued by a State or fiscal agent which prior to its being...

Application of risk-based methods to inservice testing of check valves

Energy Technology Data Exchange (ETDEWEB)

Closky, N.B.; Balkey, K.R.; McAllister, W.J. [and others

1996-12-01

Research efforts have been underway in the American Society of Mechanical Engineers (ASME) and industry to define appropriate methods for the application of risk-based technology in the development of inservice testing (IST) programs for pumps and valves in nuclear steam supply systems. This paper discusses a pilot application of these methods to the inservice testing of check valves in the emergency core cooling system of Georgia Power`s Vogtle nuclear power station. The results of the probabilistic safety assessment (PSA) are used to divide the check valves into risk-significant and less-risk-significant groups. This information is reviewed by a plant expert panel along with the consideration of appropriate deterministic insights to finally categorize the check valves into more safety-significant and less safety-significant component groups. All of the more safety-significant check valves are further evaluated in detail using a failure modes and causes analysis (FMCA) to assist in defining effective IST strategies. A template has been designed to evaluate how effective current and emerging tests for check valves are in detecting failures or in finding significant conditions that are precursors to failure for the likely failure causes. This information is then used to design and evaluate appropriate IST strategies that consider both the test method and frequency. A few of the less safety-significant check valves are also evaluated using this process since differences exist in check valve design, function, and operating conditions. Appropriate test strategies are selected for each check valve that has been evaluated based on safety and cost considerations. Test strategies are inferred from this information for the other check valves based on similar check valve conditions. Sensitivity studies are performed using the PSA model to arrive at an overall IST program that maintains or enhances safety at the lowest achievable cost.

Remote versus face-to-face check-ups for asthma.

Science.gov (United States)

Kew, Kayleigh M; Cates, Christopher J

2016-04-18

Asthma remains a significant cause of avoidable morbidity and mortality. Regular check-ups with a healthcare professional are essential to monitor symptoms and adjust medication.Health services worldwide are considering telephone and internet technologies as a way to manage the rising number of people with asthma and other long-term health conditions. This may serve to improve health and reduce the burden on emergency and inpatient services. Remote check-ups may represent an unobtrusive and efficient way of maintaining contact with patients, but it is uncertain whether conducting check-ups in this way is effective or whether it may have unexpected negative consequences. To assess the safety and efficacy of conducting asthma check-ups remotely versus usual face-to-face consultations. We identified trials from the Cochrane Airways Review Group Specialised Register (CAGR) up to 24 November 2015. We also searched www.clinicaltrials.gov, the World Health Organization (WHO) trials portal, reference lists of other reviews and contacted trial authors for additional information. We included parallel randomised controlled trials (RCTs) of adults or children with asthma that compared remote check-ups conducted using any form of technology versus standard face-to-face consultations. We excluded studies that used automated telehealth interventions that did not include personalised contact with a health professional. We included studies reported as full-text articles, as abstracts only and unpublished data. Two review authors screened the literature search results and independently extracted risk of bias and numerical data. We resolved any disagreements by consensus, and we contacted study authors for missing information.We analysed dichotomous data as odds ratios (ORs) using study participants as the unit of analysis, and continuous data as mean differences using the random-effects models. We rated all outcomes using the Grading of Recommendations Assessment, Development and

Pre-Alignment Checks. Automotive Mechanics. Steering & Suspension. Instructor's Guide [and] Student Guide.

Science.gov (United States)

Spignesi, B.

This instructional package, one in a series of individualized instructional units on automotive steering and suspension, consists of a student guide and an instructor guide dealing with prealignment checks. Covered in the module are the following steps in a prealignment check: checking the ride height of a vehicle, checking the ball joints and the…

Is drive for muscularity related to body checking behaviors in men athletes?

Directory of Open Access Journals (Sweden)

Leonardo de Sousa Fortes

Full Text Available Abstract The aim of this study was to analyze the relationship between drive for muscularity and body checking behaviors in men athletes. Two hundred and twelve Brazilian athletes over 15 years of age participated. We used the Drive for Muscularity Scale (DMS to evaluate the drive for muscularity. The Male Body Checking Questionnaire was used to assess body checking behaviors. The findings demonstrated a relationship between the "body image-oriented muscularity" subscale of the DMS and body checking behaviors (p = 0.001. The results indicated differences in body checking among athletes with high and low levels of drive for muscularity. We concluded that drive for muscularity was related to body checking behaviors in men athletes.

Assessing Personality and Mood With Adjective Check List Methodology: A Review

Science.gov (United States)

Craig, Robert J.

2005-01-01

This article addresses the benefits and problems in using adjective check list methodology to assess personality. Recent developments in this assessment method are reviewed, emphasizing seminal adjective-based personality tests (Gough's Adjective Check List), mood tests (Lubin's Depressive Adjective Test, Multiple Affect Adjective Check List),…

Spot-checks to measure general hygiene practice.

Science.gov (United States)

Sonego, Ina L; Mosler, Hans-Joachim

2016-01-01

A variety of hygiene behaviors are fundamental to the prevention of diarrhea. We used spot-checks in a survey of 761 households in Burundi to examine whether something we could call general hygiene practice is responsible for more specific hygiene behaviors, ranging from handwashing to sweeping the floor. Using structural equation modeling, we showed that clusters of hygiene behavior, such as primary caregivers' cleanliness and household cleanliness, explained the spot-check findings well. Within our model, general hygiene practice as overall concept explained the more specific clusters of hygiene behavior well. Furthermore, the higher general hygiene practice, the more likely children were to be categorized healthy (r = 0.46). General hygiene practice was correlated with commitment to hygiene (r = 0.52), indicating a strong association to psychosocial determinants. The results show that different hygiene behaviors co-occur regularly. Using spot-checks, the general hygiene practice of a household can be rated quickly and easily.

Model Checking Algorithms for CTMDPs

DEFF Research Database (Denmark)

Buchholz, Peter; Hahn, Ernst Moritz; Hermanns, Holger

2011-01-01

Continuous Stochastic Logic (CSL) can be interpreted over continuoustime Markov decision processes (CTMDPs) to specify quantitative properties of stochastic systems that allow some external control. Model checking CSL formulae over CTMDPs requires then the computation of optimal control strategie...

Efficient probabilistic model checking on general purpose graphic processors

NARCIS (Netherlands)

Bosnacki, D.; Edelkamp, S.; Sulewski, D.; Pasareanu, C.S.

2009-01-01

We present algorithms for parallel probabilistic model checking on general purpose graphic processing units (GPGPUs). For this purpose we exploit the fact that some of the basic algorithms for probabilistic model checking rely on matrix vector multiplication. Since this kind of linear algebraic

Multicriteria Analysis of Assembling Buildings from Steel Frame Structures

Science.gov (United States)

Miniotaite, Ruta

2017-10-01

Steel frame structures are often used in the construction of public and industrial buildings. They are used for: all types of slope roofs; walls of newly-built public and industrial buildings; load bearing structures; roofs of renovated buildings. The process of assembling buildings from steel frame structures should be analysed as an integrated process influenced by such factors as construction materials and machinery used, the qualification level of construction workers, complexity of work, available finance. It is necessary to find a rational technological design solution for assembling buildings from steel frame structures by conducting a multiple criteria analysis. The analysis provides a possibility to evaluate the engineering considerations and find unequivocal solutions. The rational alternative of a complex process of assembling buildings from steel frame structures was found through multiple criteria analysis and multiple criteria evaluation. In multiple criteria evaluation of technological solutions for assembling buildings from steel frame structures by pairwise comparison method the criteria by significance are distributed as follows: durability is the most important criterion in the evaluation of alternatives; the price (EUR/unit of measurement) of a part of assembly process; construction workers’ qualification level (category); mechanization level of a part of assembling process (%), and complexity of assembling work (in points) are less important criteria.

CrossCheck plagiarism screening : Experience of the Journal of Epidemiology

Science.gov (United States)

Hashimoto, Katsumi

Due to technological advances in the past two decades, researchers now have unprecedented access to a tremendous amount of useful information. However, because of the extreme pressure to publish, this abundance of information can sometimes tempt researchers to commit scientific misconduct. A serious form of such misconduct is plagiarism. Editors are always concerned about the possibility of publishing plagiarized manuscripts. The plagiarism detection tool CrossCheck allows editors to scan and analyze manuscripts effectively. The Journal of Epidemiology took part in a trial of CrossCheck, and this article discusses the concerns journal editors might have regarding the use of CrossCheck and its analysis. In addition, potential problems identified by CrossCheck, including self-plagiarism, are introduced.

CAPD Software Development for Automatic Piping System Design: Checking Piping Pocket, Checking Valve Level and Flexibility

International Nuclear Information System (INIS)

Ari Satmoko; Edi Karyanta; Dedy Haryanto; Abdul Hafid; Sudarno; Kussigit Santosa; Pinitoyo, A.; Demon Handoyo

2003-01-01

One of several steps in industrial plant construction is preparing piping layout drawing. In this drawing, pipe and all other pieces such as instrumentation, equipment, structure should be modeled A software called CAPD was developed to replace and to behave as piping drafter or designer. CAPD was successfully developed by adding both subprogram CHKUPIPE and CHKMANV. The first subprogram can check and gives warning if there is piping pocket in the piping system. The second can identify valve position and then check whether valve can be handled by operator hand The main program CAPD was also successfully modified in order to be capable in limiting the maximum length of straight pipe. By limiting the length, piping flexibility can be increased. (author)

Modelling and Analysis of Smart Grid: A Stochastic Model Checking Case Study

DEFF Research Database (Denmark)

Yuksel, Ender; Zhu, Huibiao; Nielson, Hanne Riis

2012-01-01

that require novel methods and applications. In this context, an important issue is the verification of certain quantitative properties of the system. In this paper, we consider a specific Chinese Smart Grid implementation as a case study and address the verification problem for performance and energy......Cyber-physical systems integrate information and communication technology functions to the physical elements of a system for monitoring and controlling purposes. The conversion of traditional power grid into a smart grid, a fundamental example of a cyber-physical system, raises a number of issues...... consumption. We employ stochastic model checking approach and present our modelling and analysis study using PRISM model checker....

Support of Construction and Verification of Out-of-Pile Fuel Assembly Test Facilities

International Nuclear Information System (INIS)

Park, Nam Gyu; Kim, K. T.; Park, J. K.

2006-12-01

Fuel assembly and components should be verified by the out-of-pile test facilities in order to load the developed fuel in reactor. Even though most of the component-wise tests have been performed using the facilities in land, the assembly-wise tests has been depended on the oversees' facility due to the lack of the facilities. KAERI started to construct the assembly-wise mechanical/hydraulic test facilities and KNF, as an end user, is supporting the mechanical/hydraulic test facility construction by using the technologies studied through the fuel development programs. The works performed are as follows: - Test assembly shipping container design and manufacturing support - Fuel handling tool design : Gripper, Upper and lower core simulators for assembly mechanical test facility, Internals for assembly hydraulic test facility - Manufacture of test specimens : skeleton and assembly for preliminary functional verification of assembly mechanical/hydraulic test facilities, two assemblies for the verification of assembly mechanical/hydraulic test facilities, Instrumented rod design and integrity evaluation - Verification of assembly mechanical/hydraulic test facilities : test data evaluation

Support of Construction and Verification of Out-of-Pile Fuel Assembly Test Facilities

Energy Technology Data Exchange (ETDEWEB)

Park, Nam Gyu; Kim, K. T.; Park, J. K. [KNF, Daejeon (Korea, Republic of)] (and others)

2006-12-15

Fuel assembly and components should be verified by the out-of-pile test facilities in order to load the developed fuel in reactor. Even though most of the component-wise tests have been performed using the facilities in land, the assembly-wise tests has been depended on the oversees' facility due to the lack of the facilities. KAERI started to construct the assembly-wise mechanical/hydraulic test facilities and KNF, as an end user, is supporting the mechanical/hydraulic test facility construction by using the technologies studied through the fuel development programs. The works performed are as follows: - Test assembly shipping container design and manufacturing support - Fuel handling tool design : Gripper, Upper and lower core simulators for assembly mechanical test facility, Internals for assembly hydraulic test facility - Manufacture of test specimens : skeleton and assembly for preliminary functional verification of assembly mechanical/hydraulic test facilities, two assemblies for the verification of assembly mechanical/hydraulic test facilities, Instrumented rod design and integrity evaluation - Verification of assembly mechanical/hydraulic test facilities : test data evaluation.

The development of flow test technology for PWR fuel assembly

International Nuclear Information System (INIS)

Chung, Moon Ki; Cha, Chong Hee; Chung, Chang Hwan; Chun, Se Young; Song, Chul Hwa; Chung, Heung Joon; Won, Soon Yeun; Cho, Yeong Rho; Kim, Bok Deuk

1988-05-01

KAERI has an extensive program to develope PWR fuel assembly. In relation to the program, development of flow test technology is needed to evaluate the thermal hydraulic compactibility and mechanical integrity of domestically fabricated nuclear fuels. A high-pressure and high-temperature flow test facility was designed to test domestically fabricated fuel assembly. The test section of the facility has capacity of a 6x6 full length PWR fuel assembly. A flow test rig was designed and installed at Cold Test Loop to carry out model experiments with 5x5 rod assembly under atmosphere pressure to get information about the characteristics of pressure loss of spacer grids and velocity distribution in the subchannels. LDV measuring technology was established using TSI's Laser Dopper Velocimeter 9100-3 System

Experimental investigation of the check valve behaviour when the flow is reversing

Directory of Open Access Journals (Sweden)

Himr D.

2017-01-01

Full Text Available Check valve in a pipeline is supposed to prevent the reverse flow and to allow the flow in the positive direction. The construction of check valves follows these requirements, but the check valve must not cause pressure pulsations in transients. It means when the fluid is accelerating or decelerating. The article describes an experimental investigation of a swing check valve when the flow is changing its direction. The check valve was placed in an experimental circuit, where the pressure on the upstream and downstream side of the valve was measured and the current value of flow rate was determined. The goal was to simulate conditions in the real system, where the check valve slam had been observed.

IRaPPA: information retrieval based integration of biophysical models for protein assembly selection.

Science.gov (United States)

Moal, Iain H; Barradas-Bautista, Didier; Jiménez-García, Brian; Torchala, Mieczyslaw; van der Velde, Arjan; Vreven, Thom; Weng, Zhiping; Bates, Paul A; Fernández-Recio, Juan

2017-06-15

In order to function, proteins frequently bind to one another and form 3D assemblies. Knowledge of the atomic details of these structures helps our understanding of how proteins work together, how mutations can lead to disease, and facilitates the designing of drugs which prevent or mimic the interaction. Atomic modeling of protein-protein interactions requires the selection of near-native structures from a set of docked poses based on their calculable properties. By considering this as an information retrieval problem, we have adapted methods developed for Internet search ranking and electoral voting into IRaPPA, a pipeline integrating biophysical properties. The approach enhances the identification of near-native structures when applied to four docking methods, resulting in a near-native appearing in the top 10 solutions for up to 50% of complexes benchmarked, and up to 70% in the top 100. IRaPPA has been implemented in the SwarmDock server ( http://bmm.crick.ac.uk/∼SwarmDock/ ), pyDock server ( http://life.bsc.es/pid/pydockrescoring/ ) and ZDOCK server ( http://zdock.umassmed.edu/ ), with code available on request. moal@ebi.ac.uk. Supplementary data are available at Bioinformatics online. © The Author 2017. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com

Masking potency and whiteness of noise at various noise check sizes.

Science.gov (United States)

Kukkonen, H; Rovamo, J; Näsänen, R

1995-02-01

The masking effect of spatial noise can be increased by increasing either the rms contrast or check size of noise. In this study, the authors investigated the largest noise check size that still mimics the effect of white noise in grating detection and how it depends on the bandwidth and spatial frequency of a grating. The authors measured contrast energy thresholds, E, for vertical cosine gratings at various spatial frequencies and bandwidths. Gratings were embedded in two-dimensional spatial noise. The side length of the square noise checks was varied in the experiments. The spectral density, N(0,0), of white spatial noise at zero frequency was calculated by multiplying the noise check area by the rms contrast of noise squared. The physical signal-to-noise ratio at threshold [E/N(0,0)]0.5 was initially constant but then started to decrease. The largest noise check that still produced a constant physical signal-to-noise ratio at threshold was directly proportional to the spatial frequency. When expressed as a fraction of grating cycle, the largest noise check size depended only on stimulus bandwidth. The smallest number of noise checks per grating cycle needed to mimic the effect of white noise decreased from 4.2 to 2.6 when the number of grating cycles increased from 1 to 64. Spatial noise can be regarded as white in grating detection if there are at least four square noise checks per grating cycle at all spatial frequencies.

Electric Field Guided Assembly of One-Dimensional Nanostructures for High Performance Sensors

Directory of Open Access Journals (Sweden)

Wing Kam Liu

2012-05-01

Full Text Available Various nanowire or nanotube-based devices have been demonstrated to fulfill the anticipated future demands on sensors. To fabricate such devices, electric field-based methods have demonstrated a great potential to integrate one-dimensional nanostructures into various forms. This review paper discusses theoretical and experimental aspects of the working principles, the assembled structures, and the unique functions associated with electric field-based assembly. The challenges and opportunities of the assembly methods are addressed in conjunction with future directions toward high performance sensors.

Study of check image using computed radiography

International Nuclear Information System (INIS)

Sato, Hiroshi

2002-01-01

There are two image forming methods both a check image and a portal image in the linacogram. It has been established the image forming method in the check image using computed radiography (CR). On the other hand, it is not established the image forming method in the portal image using CR yet. Usually, in the electric portal imaging device (EPID) is mainly used just before radiotherapy start. The usefulness of the portal image forming method by CR using in place of EPID is possible to confirm the precision for determining to specific position at the irradiate part and to the irradiate method for the human organs. There are some technical problems that, since in the early time, the linac graphy (LG) image have low resolution power. In order to improve to the resolution power in LG image, CR image technologies have been introduced to the check image forming method. Heavy metallic sheet (HMS) is used to the front side of CR-IP cassette, and high contactness sponge is used to the back side of the cassette. Improved contactness between HMS and imaging plate (IP) by means of the high contactness sponge contributed to improve the resolution power in the check images. A lot of paper which is connected with these information have been reported. Imaging plate ST-III should be used to maintain high sensitivity in the check film image forming method. The same image forming method in the check image established by CR has been introduced into the portal image forming method in order to improve the resolution power. However, as a result, it couldn't acquired high resolution image forming in the portal images because of the combination of ST-III and radiotherapy dose. After several trials, it has been recognized that HR-V imaging plate for mammography is the most useful application to maintain high resolution power in the portal images. Also, it is possible to modify the image quality by changing GS parameter which is one of image processing parameters in CR. Furthermore, in case

Model checking biological systems described using ambient calculus

DEFF Research Database (Denmark)

Mardare, Radu Iulian; Priami, Corrado; Qualia, Paola

2005-01-01

Model checking biological systems described using ambient calculus. In Proc. of the second International Workshop on Computational Methods in Systems Biology (CMSB04), Lecture Notes in Bioinformatics 3082:85-103, Springer, 2005.......Model checking biological systems described using ambient calculus. In Proc. of the second International Workshop on Computational Methods in Systems Biology (CMSB04), Lecture Notes in Bioinformatics 3082:85-103, Springer, 2005....

Model Checking the Remote Agent Planner

Science.gov (United States)

Khatib, Lina; Muscettola, Nicola; Havelund, Klaus; Norvig, Peter (Technical Monitor)

2001-01-01

This work tackles the problem of using Model Checking for the purpose of verifying the HSTS (Scheduling Testbed System) planning system. HSTS is the planner and scheduler of the remote agent autonomous control system deployed in Deep Space One (DS1). Model Checking allows for the verification of domain models as well as planning entries. We have chosen the real-time model checker UPPAAL for this work. We start by motivating our work in the introduction. Then we give a brief description of HSTS and UPPAAL. After that, we give a sketch for the mapping of HSTS models into UPPAAL and we present samples of plan model properties one may want to verify.

Feasible reactor power cutback logic development for an integral reactor

International Nuclear Information System (INIS)

Han, Soon-Kyoo; Lee, Chung-Chan; Choi, Suhn; Kang, Han-Ok

2013-01-01

Major features of integral reactors that have been developed around the world recently are simplified operating systems and passive safety systems. Even though highly simplified control system and very reliable components are utilized in the integral reactor, the possibility of major component malfunction cannot be ruled out. So, feasible reactor power cutback logic is required to cope with the malfunction of components without inducing reactor trip. Simplified reactor power cutback logic has been developed on the basis of the real component data and operational parameters of plant in this study. Due to the relatively high rod worth of the integral reactor the control rod assembly drop method which had been adapted for large nuclear power plants was not desirable for reactor power cutback of the integral reactor. Instead another method, the control rod assembly control logic of reactor regulating system controls the control rod assembly movements, was chosen as an alternative. Sensitivity analyses and feasibility evaluations were performed for the selected method by varying the control rod assembly driving speed. In the results, sensitivity study showed that the performance goal of reactor power cutback system could be achieved with the limited range of control rod assembly driving speed. (orig.)

Simple nonparametric checks for model data fit in CAT

NARCIS (Netherlands)

Meijer, R.R.

2005-01-01

In this paper, the usefulness of several nonparametric checks is discussed in a computerized adaptive testing (CAT) context. Although there is no tradition of nonparametric scalability in CAT, it can be argued that scalability checks can be useful to investigate, for example, the quality of item

Dynamic State Space Partitioning for External Memory Model Checking

DEFF Research Database (Denmark)

Evangelista, Sami; Kristensen, Lars Michael

2009-01-01

We describe a dynamic partitioning scheme usable by model checking techniques that divide the state space into partitions, such as most external memory and distributed model checking algorithms. The goal of the scheme is to reduce the number of transitions that link states belonging to different...

Creating Büchi automata for multi-valued model checking

NARCIS (Netherlands)

Vijzelaar, Stefan J.J.; Fokkink, Wan J.

2017-01-01

In explicit state model checking of linear temporal logic properties, a Büchi automaton encodes a temporal property. It interleaves with a Kripke model to form a state space, which is searched for counterexamples. Multi-valued model checking considers additional truth values beyond the Boolean true

Amino Acid Availability Modulates Vacuolar H+-ATPase Assembly*

Science.gov (United States)

Stransky, Laura A.; Forgac, Michael

2015-01-01

The vacuolar H+-ATPase (V-ATPase) is an ATP-dependent proton pump composed of a peripheral ATPase domain (V1) and a membrane-integral proton-translocating domain (V0) and is involved in many normal and disease processes. An important mechanism of regulating V-ATPase activity is reversible assembly of the V1 and V0 domains. Increased assembly in mammalian cells occurs under various conditions and has been shown to involve PI3K. The V-ATPase is necessary for amino acid-induced activation of mechanistic target of rapamycin complex 1 (mTORC1), which is important in controlling cell growth in response to nutrient availability and growth signals. The V-ATPase undergoes amino acid-dependent interactions with the Ragulator complex, which is involved in recruitment of mTORC1 to the lysosomal membrane during amino acid sensing. We hypothesized that changes in the V-ATPase/Ragulator interaction might involve amino acid-dependent changes in V-ATPase assembly. To test this, we measured V-ATPase assembly by cell fractionation in HEK293T cells treated with and without amino acids. V-ATPase assembly increases upon amino acid starvation, and this effect is reversed upon readdition of amino acids. Lysosomes from amino acid-starved cells possess greater V-ATPase-dependent proton transport, indicating that assembled pumps are catalytically active. Amino acid-dependent changes in both V-ATPase assembly and activity are independent of PI3K and mTORC1 activity, indicating the involvement of signaling pathways distinct from those implicated previously in controlling assembly. By contrast, lysosomal neutralization blocks the amino acid-dependent change in assembly and reactivation of mTORC1 after amino acid starvation. These results identify an important new stimulus for controlling V-ATPase assembly. PMID:26378229

Lightweight IMM Multi-Junction Photovoltaic Flexible Blanket Assembly, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — DSS's recently completed successful NASA SBIR Phase 1 program has established a TRL 3/4 classification for an innovative IMM PV Integrated Modular Blanket Assembly...

Fuel assembly

International Nuclear Information System (INIS)

Ueda, Makoto.

1991-01-01

In a fuel assembly in which spectral shift type moderator guide members are arranged, the moderator guide member has a flow channel resistance member, that provides flow resistance against the moderators, in the upstream of a moderator flowing channel, by which the ratio of removing coolants is set greater at the upstream than downstream. With such a constitution, the void distribution increasing upward in the channel box except for the portion of the moderator guide member is moderated by the increase of the area of the void region that expands downward in the guide member. Accordingly, the axial power distribution is flattened throughout the operation cycle and excess distortion is eliminated to improve the fuel integrity. (T.M.)

Acoustic emission testing of piston check valves

International Nuclear Information System (INIS)

Stewart, D.L.

1994-01-01

Based on test experience at Comanche Peak Unit 1, an acoustic emission data evaluation matrix for piston check valves has been developed. The degradations represented in this matrix were selected based on Edwards piston check valve failure data reported in the Nuclear Plant Reliability Data System. Evidence to support this matrix was collected from site test data on a variety of valve types. Although still under refinement, the matrix provides three major attributes for closure verification, which have proven useful in developing test procedures for inservice testing and preventing unnecessary disassembly

Symbolic Dependency Graphs for PCTL Model-Checking

DEFF Research Database (Denmark)

Mariegaard, Anders; Larsen, Kim Guldstrand

2017-01-01

We consider the problem of model-checking a subset of probabilistic CTL, interpreted over (discrete-time) Markov reward models, allowing the specification of lower bounds on the probability of the set of paths satisfying a cost-bounded path formula. We first consider a reduction to fixed-point co......We consider the problem of model-checking a subset of probabilistic CTL, interpreted over (discrete-time) Markov reward models, allowing the specification of lower bounds on the probability of the set of paths satisfying a cost-bounded path formula. We first consider a reduction to fixed...

Molecular Assemblies, Genes and Genomics Integrated Efficiently (MAGGIE)

Energy Technology Data Exchange (ETDEWEB)

Baliga, Nitin S

2011-05-26

Final report on MAGGIE. We set ambitious goals to model the functions of individual organisms and their community from molecular to systems scale. These scientific goals are driving the development of sophisticated algorithms to analyze large amounts of experimental measurements made using high throughput technologies to explain and predict how the environment influences biological function at multiple scales and how the microbial systems in turn modify the environment. By experimentally evaluating predictions made using these models we will test the degree to which our quantitative multiscale understanding wilt help to rationally steer individual microbes and their communities towards specific tasks. Towards this end we have made substantial progress towards understanding evolution of gene families, transcriptional structures, detailed structures of keystone molecular assemblies (proteins and complexes), protein interactions, biological networks, microbial interactions, and community structure. Using comparative analysis we have tracked the evolutionary history of gene functions to understand how novel functions evolve. One level up, we have used proteomics data, high-resolution genome tiling microarrays, and 5' RNA sequencing to revise genome annotations, discover new genes including ncRNAs, and map dynamically changing operon structures of five model organisms: For Desulfovibrio vulgaris Hildenborough, Pyrococcus furiosis, Sulfolobus solfataricus, Methanococcus maripaludis and Haiobacterium salinarum NROL We have developed machine learning algorithms to accurately identify protein interactions at a near-zero false positive rate from noisy data generated using tagfess complex purification, TAP purification, and analysis of membrane complexes. Combining other genome-scale datasets produced by ENIGMA (in particular, microarray data) and available from literature we have been able to achieve a true positive rate as high as 65% at almost zero false positives

EASY-2005: Validation and new tools for data checking

International Nuclear Information System (INIS)

Forrest, R.A.; Kopecky, J.

2007-01-01

The European Activation System (EASY) has been developed for activation calculations within the Fusion Technology programme. It comprises the EAF nuclear data libraries and the FISPACT inventory code. EASY-2005 contains about five times more neutron-induced reactions (62,637) than the previous version; due to an increase in the upper energy limit from 20 to 60 MeV. Many measurements of activation in well-defined neutron spectra have been made; these integral results are used to validate EAF. Details of the validation covering 453 reactions are given. Model calculations were used to produce the majority of the data, and the large number of reactions, and the lack of experimental data, make it necessary to develop new checking tools. Within the SAFEPAQ-II code, the new methodology of statistical analysis of cross sections (SACS) has been developed. This enables various quantities such as maximum cross section (σ max ) to be plotted as a function of asymmetry parameter (s) for each reaction type. Such plots show well-defined trends and inconsistent data for a particular reaction can readily be identified. The use of integral data and SACS for improvement are discussed, in relation to the maintenance version, EASY-2005.1 and the planned new version, EASY-2007

Seismic Response Analysis of Assembled Reactor Vessel Internals

International Nuclear Information System (INIS)

Je, Sang-Yun; Chang, Yoon-Suk; Kang, Sung-Sik

2015-01-01

RVIs (Reactor Vessel Internals) perform important safe-related functions such as upholding the nuclear fuel assembly as well as providing the coolant passage of the reactor core and supporting the control rod drive mechanism. Therefore, the components including RVIs have to be designed and constructed taking into account the structural integrity under various accident scenarios. The reliable seismic analysis is essentially demanded to maintain the safe-related functions of RVIs. In this study, a modal analysis was performed based on the previous researches to examine values of frequencies, mode shapes and participation factors. Subsequently, the structural integrity respecting to the earthquake was evaluated through a response spectrum analysis by using the output variables of modal analysis. In this study, the structural integrity of the assembled RVIs was carried out against the seismic event via the modal and response spectrum analyses. Even though 287MPa of the maximum stress value occurred at the connected region between UGS and CSA, which was lower than its allowable value. At present, fluid-structure interaction effects are being examined for further realistic simulation, which will be reported in the near future

Checking in: An Analysis of the (Lack of) Body Checking in Women's Ice Hockey

Science.gov (United States)

Weaving, Charlene; Roberts, Samuel

2012-01-01

Despite the growing popularity of women's ice hockey in North America, players continue to face limitations because of the prohibition of body checking. In this paper, we argue from a liberal feminist philosophical perspective that this prohibition reinforces existing traditional stereotypes of female athletes. Because the women's game does not…

Detailed channel thermal-hydraulic calculation of nuclear reactor fuel assemblies

International Nuclear Information System (INIS)

Zhukov, A.V.; Sorokin, A.P.; Ushakov, P.A.; Yur'ev, Yu.S.

1981-01-01

The system of equations of mass balance, quantity of motion and energy used in calculation of nuclear reactor fuel assemblies is obtained. The equation system is obtained on the base of integral equations of hydrodynamics interaction in assemblies of smooth fuel elements and fuel elements with wire packing. The calculation results of coolant heating distributions by the fast reactor assembly channels are presented. The analysis of the results obtained shows that interchannel exchange essentially uniforms the coolant heating distribution in the peripheral range of the assembly but it does not remove non-uniformity caused by power distribution non-uniformity in the cross section. Geometry of the peripheral assembly range plays an essential role in the heating distribution. Change of the calculation gap between the peripheral fuel elements and assembly shells can result either in superheating or in subcooling in the peripheral channels relatively to joint internal channels of the assembly. Heat supply to the coolant passing through interassembly gaps decreases temperature in the assembly periphery and results in the increase of temperature non-uniformity by the perimeter of peripheral fuel elements. It is concluded that the applied method of the channel-by-channel calculation is ef-- fective in thermal-physical calculation of nuclear reactor fuel assemblies and it permits to solve a wide range of problems [ru

16 CFR 240.12 - Checking customer's use of payments.

Science.gov (United States)

2010-01-01

... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Checking customer's use of payments. 240.12 Section 240.12 Commercial Practices FEDERAL TRADE COMMISSION GUIDES AND TRADE PRACTICE RULES GUIDES FOR ADVERTISING ALLOWANCES AND OTHER MERCHANDISING PAYMENTS AND SERVICES § 240.12 Checking customer's use of...

Analysis of subcritical control rod worth measurements in assembly BZB/3

International Nuclear Information System (INIS)

Giese, H.

1981-07-01

A series of subcritical absorber array measurements was performed in version three of the BIZET assembly BZB in order to check the ability of standard reactor computational codes used by the BIZET participants in predicting control rod worths in large fast reactors. Assembly BZB/3 was a two-zone core with a diameter of about 2.5 m and a core height of 0.89 m, fuelled with plutonium. Fifteen control rod positions and twelve secondary shutdown rod positions were simulated in the core. The measurements comprised the insertion of single absorbers as well as various groups of absorbers and were based on the modified source multiplication method. The KfK analysis was confined to the calculation of eigenvalues for different absorber arrays, also with a view to a comparison with the results of a former BZA evaluation with calculation-to-experiment values of up to C/E ∼ 1.10. The C/E-values found for BZB/3 ranged from 1.02 to 1.10 and did not show a systematic variation at different radial positions or different degrees of absorber asymmetry

Regular Check-Ups Are Important

Science.gov (United States)

... Attack Wear Red for Heart Health Tools for Pregnant Women, New Moms, Women Considering Pregnancy Be a Healthy ... your community (i.e. a faith-based setting, workplace, school, or civic group) ... screening on National Women’s Check-Up Day (the day after Mother’s Day ...

Checking behavioral conformance of artifacts

NARCIS (Netherlands)

Fahland, D.; Leoni, de M.; Dongen, van B.F.; Aalst, van der W.M.P.

2011-01-01

The usefulness of process models (e.g., for analysis, improvement, or execution) strongly depends on their ability to describe reality. Conformance checking is a technique to validate how good a given process model describes recorded executions of the actual process. Recently, artifacts have been

Toward allotetraploid cotton genome assembly: integration of a high-density molecular genetic linkage map with DNA sequence information

Science.gov (United States)

2012-01-01

Background Cotton is the world’s most important natural textile fiber and a significant oilseed crop. Decoding cotton genomes will provide the ultimate reference and resource for research and utilization of the species. Integration of high-density genetic maps with genomic sequence information will largely accelerate the process of whole-genome assembly in cotton. Results In this paper, we update a high-density interspecific genetic linkage map of allotetraploid cultivated cotton. An additional 1,167 marker loci have been added to our previously published map of 2,247 loci. Three new marker types, InDel (insertion-deletion) and SNP (single nucleotide polymorphism) developed from gene information, and REMAP (retrotransposon-microsatellite amplified polymorphism), were used to increase map density. The updated map consists of 3,414 loci in 26 linkage groups covering 3,667.62 cM with an average inter-locus distance of 1.08 cM. Furthermore, genome-wide sequence analysis was finished using 3,324 informative sequence-based markers and publicly-available Gossypium DNA sequence information. A total of 413,113 EST and 195 BAC sequences were physically anchored and clustered by 3,324 sequence-based markers. Of these, 14,243 ESTs and 188 BACs from different species of Gossypium were clustered and specifically anchored to the high-density genetic map. A total of 2,748 candidate unigenes from 2,111 ESTs clusters and 63 BACs were mined for functional annotation and classification. The 337 ESTs/genes related to fiber quality traits were integrated with 132 previously reported cotton fiber quality quantitative trait loci, which demonstrated the important roles in fiber quality of these genes. Higher-level sequence conservation between different cotton species and between the A- and D-subgenomes in tetraploid cotton was found, indicating a common evolutionary origin for orthologous and paralogous loci in Gossypium. Conclusion This study will serve as a valuable genomic resource

Pressure effects on lipids and bio-membrane assemblies

Directory of Open Access Journals (Sweden)

Nicholas J. Brooks

2014-11-01

Full Text Available Membranes are amongst the most important biological structures; they maintain the fundamental integrity of cells, compartmentalize regions within them and play an active role in a wide range of cellular processes. Pressure can play a key role in probing the structure and dynamics of membrane assemblies, and is also critical to the biology and adaptation of deep-sea organisms. This article presents an overview of the effect of pressure on the mesostructure of lipid membranes, bilayer organization and lipid–protein assemblies. It also summarizes recent developments in high-pressure structural instrumentation suitable for experiments on membranes.

SU-D-BRD-07: Automatic Patient Data Audit and Plan Quality Check to Support ARIA and Eclipse

Energy Technology Data Exchange (ETDEWEB)

Li, X; Li, H; Wu, Y; Mutic, S; Yang, D [Washington University School of Medicine, St. Louis, MO (United States)

2014-06-01

Purpose: To ensure patient safety and treatment quality in RT departments that use Varian ARIA and Eclipse, we developed a computer software system and interface functions that allow previously developed electron chart checking (EcCk) methodologies to support these Varian systems. Methods: ARIA and Eclipse store most patient information in its MSSQL database. We studied the contents in the hundreds database tables and identified the data elements used for patient treatment management and treatment planning. Interface functions were developed in both c-sharp and MATLAB to support data access from ARIA and Eclipse servers using SQL queries. These functions and additional data processing functions allowed the existing rules and logics from EcCk to support ARIA and Eclipse. Dose and structure information are important for plan quality check, however they are not stored in the MSSQL database but as files in Varian private formats, and cannot be processed by external programs. We have therefore implemented a service program, which uses the DB Daemon and File Daemon services on ARIA server to automatically and seamlessly retrieve dose and structure data as DICOM files. This service was designed to 1) consistently monitor the data access requests from EcCk programs, 2) translate the requests for ARIA daemon services to obtain dose and structure DICOM files, and 3) monitor the process and return the obtained DICOM files back to EcCk programs for plan quality check purposes. Results: EcCk, which was previously designed to only support MOSAIQ TMS and Pinnacle TPS, can now support Varian ARIA and Eclipse. The new EcCk software has been tested and worked well in physics new start plan check, IMRT plan integrity and plan quality checks. Conclusion: Methods and computer programs have been implemented to allow EcCk to support Varian ARIA and Eclipse systems. This project was supported by a research grant from Varian Medical System.

Is there a need for special preventive medical check-ups in employees exposed to experimental animal dust?

Science.gov (United States)

Schmid, Klaus; Jüngert, Barbara; Hager, Meta; Drexler, Hans

2009-02-01

Due to new legal requirements in Germany, the employer must request preventive medical check-ups for activities involving exposure to dust from experimental animals in the rooms in which the animals are kept. The objective is to report our first experiences with these medical check-ups in the context of academic research. The check-ups were carried out since November 2005 and comprised a questionnaire and a medical examination, including a pulmonary function test with whole-body plethysmography. Respiratory, nasal and ocular symptoms related to occupational exposure to animals were documented. Participation in skin prick tests (ubiquitous inhalation allergens and laboratory animal allergens), a bronchial provocation test with methacholine, and serological examinations for total IgE and specific IgE antibodies was voluntary. Data on 132 persons are presented. One hundred and six of these had already been exposed for at least 1 year. Main complaints at the workplace were sneezing and runny nose. Ocular symptoms and bronchial asthma were reported infrequently. The development of at least one of these symptoms occurred in 34% of employees with an exposure of at least 1 year. If the weekly exposure duration was at least 5 h, the proportion of employees with complaints rose to 44.9%. In employees occupationally exposed to mice and rats, work-related complaints occurred in 33.7 and 37.8%, respectively, and sensitisation rates were 12.7 and 16.3%, respectively. Employees with and without complaints differed in history of allergic symptoms, and workplace safety measures. In employees with occupational contact with laboratory animal dust, the frequency of complaints was high. The results confirm the necessity of regular medical check-ups for employees with contact with laboratory animal dust. Nevertheless, the medical check-ups must be part of a prevention strategy including education, engineering controls, administrative controls, use of personal protective equipment and

SU-D-BRD-07: Automatic Patient Data Audit and Plan Quality Check to Support ARIA and Eclipse

International Nuclear Information System (INIS)

Li, X; Li, H; Wu, Y; Mutic, S; Yang, D

2014-01-01

Purpose: To ensure patient safety and treatment quality in RT departments that use Varian ARIA and Eclipse, we developed a computer software system and interface functions that allow previously developed electron chart checking (EcCk) methodologies to support these Varian systems. Methods: ARIA and Eclipse store most patient information in its MSSQL database. We studied the contents in the hundreds database tables and identified the data elements used for patient treatment management and treatment planning. Interface functions were developed in both c-sharp and MATLAB to support data access from ARIA and Eclipse servers using SQL queries. These functions and additional data processing functions allowed the existing rules and logics from EcCk to support ARIA and Eclipse. Dose and structure information are important for plan quality check, however they are not stored in the MSSQL database but as files in Varian private formats, and cannot be processed by external programs. We have therefore implemented a service program, which uses the DB Daemon and File Daemon services on ARIA server to automatically and seamlessly retrieve dose and structure data as DICOM files. This service was designed to 1) consistently monitor the data access requests from EcCk programs, 2) translate the requests for ARIA daemon services to obtain dose and structure DICOM files, and 3) monitor the process and return the obtained DICOM files back to EcCk programs for plan quality check purposes. Results: EcCk, which was previously designed to only support MOSAIQ TMS and Pinnacle TPS, can now support Varian ARIA and Eclipse. The new EcCk software has been tested and worked well in physics new start plan check, IMRT plan integrity and plan quality checks. Conclusion: Methods and computer programs have been implemented to allow EcCk to support Varian ARIA and Eclipse systems. This project was supported by a research grant from Varian Medical System

Progress realized by numerized Eddy current checking-chains

International Nuclear Information System (INIS)

Guerin, F.; Blanchet, A.

1985-01-01

Until the last ten years , the tubes of the Steam Generators of the Nuclear Stations were inspected by means of Eddy Current with analogical checkings-chains. HBS Company has perfected a numerized checking-chain allowing transmission up to 300 m of the E.C. signals. In a near future, it will be then possible to do periodical inspections of Steam Generators from cabins located out of the reactor building [fr

Adjustments in channel morphology due to land-use changes and check dam installation in mountain torrents of Calabria (Southern Italy)

Science.gov (United States)

Fortugno, Diego; Zema, Demetrio Antonio; Bombino, Giuseppe; Tamburino, Vincenzo; Quinonero Rubio, Juan Manuel; Boix-Fayos, Carolina

2016-04-01

In Mediterranean semi-arid conditions the geomorphic effects of land-use changes and check dam installation on active channel headwater morphology are not completely understood. In such environments, the availability of specific studies, which monitor channel adjustments as a response to reforestation and check dams over representative observation periods, could help develop new management strategies and erosion control measures. This investigation is an integrated approach assessing the adjustments of channel morphology in a typical torrent (Sant'Agata, Calabria, Southern Italy) after land-use changes (e.g. fire, reforestation, land abandonment) and check dam construction across a period of about 60 years (1955-2012). A statistical analysis of historical rainfall records, an analysis of land-use change in the catchment area and a geomorphological mapping of channel adjustments were carried out and combined with field surveys of bed surface grain-size over a 5-km reach including 14 check dams. The analysis of the historical rainfall records showed a slight decrease in the amount and erosivity of precipitation. Mapping of land-use changes highlighted a general increase of vegetal coverage on the slopes adjacent to the monitored reaches. Together with the check dam network installation, this increase could have induced a reduction in water and sediment supply. The different erosional and depositional forms and adjustments showed a general narrowing between consecutive check dams together with local modifications detected upstream (bed aggradation and cross section expansion together with low-flow realignments) and downstream (local incision) of the installed check dams. Changes in the torrent bends were also detected as a response to erosional and depositional processes with different intensities. The study highlighted: (i) the efficiency of check dams against the disrupting power of the most intense floods by stabilising the active channel; and (ii) the influence of

A novel cognitive intervention for compulsive checking: Targeting maladaptive beliefs about memory.

Science.gov (United States)

Alcolado, Gillian M; Radomsky, Adam S

2016-12-01

Compulsive checking is one of the most common symptoms of obsessive-compulsive disorder (OCD). Recently it has been proposed that those who check compulsively may believe their memory is poor, rather than having an actual memory impairment. The current study sought to develop and assess a brief cognitive intervention focused on improving maladaptive beliefs about memory, as they pertain to both checking symptoms and memory performance. Participants (N = 24) with a diagnosis of OCD and clinical levels of checking symptomatology were randomly assigned either to receive two weekly 1-hour therapy sessions or to self-monitor during a similar waitlist period. Time spent checking, checking symptoms, maladaptive beliefs about memory, and visuospatial memory were assessed both pre- and post-treatment/waitlist. Results showed that compared to the waitlist condition, individuals in the treatment condition displayed significant decreases in their maladaptive beliefs about memory and checking symptoms from pre- to post-intervention. They also exhibited increased recall performance on a measure of visuospatial memory. Changes in beliefs about memory were predictors of reduced post-intervention checking, but were not predictive of increased post-intervention memory scores. The lack of long term follow-up data and use of a waitlist control leave questions about the stability and specificity of the intervention. Findings provide preliminary evidence that strategies targeting beliefs about memory may be worthy of inclusion in cognitive-behavioural approaches to treating compulsive checking. Copyright © 2015 Elsevier Ltd. All rights reserved.

[Factors Associated with Stress Check Attendance: Possible Effect of Timing of Annual Health Examination].

Science.gov (United States)

Ishimaru, Tomohiro; Hattori, Michihiro; Nagata, Masako; Kuwahara, Keisuke; Watanabe, Seiji; Mori, Koji

2018-01-01

The stress check program has been part of annual employees' health screening since 2015. Employees are recommended, but not obliged, to undergo the stress check offered. This study was designed to examine the factors associated with stress check attendance. A total of 31,156 Japanese employees who underwent an annual health examination and a stress check service at an Occupational Health Service Center in 2016 participated in this study. Data from the annual health examination and stress check service included stress check attendance, date of attendance (if implemented), gender, age, workplace industry, number of employees at the workplace, and tobacco and alcohol consumption. Data were analyzed using multiple logistic regression. The mean rate of stress check attendance was 90.8%. A higher rate of stress check attendance was associated with a lower duration from the annual health examination, age ≥30 years, construction and transport industry, and 50-999 employees at the workplace. A lower rate of stress check attendance was associated with medical and welfare industry and ≥1,000 employees at the workplace. These findings provide insights into developing strategies for improving the rate of stress check attendance. In particular, stress check attendance may improve if the stress check service and annual health examination are conducted simultaneously.

Development of a butterfly check valve model under natural circulation conditions

International Nuclear Information System (INIS)

Rao, Yuxian; Yu, Lei; Fu, Shengwei; Zhang, Fan

2015-01-01

Highlights: • Bases on Lim’s swing check valve model, a butterfly check valve model was developed. • The method to quantify the friction torque T F in Li’s model was corrected. • The developed model was implemented into the RELAP5 code and verified. - Abstract: A butterfly check valve is widely used to prevent a reverse flow in the pipe lines of a marine nuclear power plant. Under some conditions, the natural circulation conditions in particular, the fluid velocity through the butterfly check valve might become too low to hold the valve disk fully open, thereby the flow resistance of the butterfly check valve varies with the location of the valve disk and as a result the fluid flow is significantly affected by the dynamic motion of the valve disk. Simulation of a pipe line that includes some butterfly check valves, especially under natural circulation conditions, is thus complicated. This paper focuses on the development of a butterfly check valve model to enhance the capability of the thermal–hydraulic system code and the developed model is implemented into the RELAP5 code. Both steady-state calculations and transient calculations were carried out for the primary loop system of a marine nuclear power plant and the calculation results are compared with the experimental data for verification purpose. The simulation results show an agreement with the experimental data

Genomes correction and assembling: present methods and tools

Science.gov (United States)

Wojcieszek, Michał; Pawełkowicz, Magdalena; Nowak, Robert; Przybecki, Zbigniew

2014-11-01

Recent rapid development of next generation sequencing (NGS) technologies provided significant impact into genomics field of study enabling implementation of many de novo sequencing projects of new species which was previously confined by technological costs. Along with advancement of NGS there was need for adjustment in assembly programs. New algorithms must cope with massive amounts of data computation in reasonable time limits and processing power and hardware is also an important factor. In this paper, we address the issue of assembly pipeline for de novo genome assembly provided by programs presently available for scientist both as commercial and as open - source software. The implementation of four different approaches - Greedy, Overlap - Layout - Consensus (OLC), De Bruijn and Integrated resulting in variation of performance is the main focus of our discussion with additional insight into issue of short and long reads correction.

Discrete-time rewards model-checked

NARCIS (Netherlands)

Larsen, K.G.; Andova, S.; Niebert, Peter; Hermanns, H.; Katoen, Joost P.

2003-01-01

This paper presents a model-checking approach for analyzing discrete-time Markov reward models. For this purpose, the temporal logic probabilistic CTL is extended with reward constraints. This allows to formulate complex measures – involving expected as well as accumulated rewards – in a precise and

Schedulability of Herschel revisited using statistical model checking

DEFF Research Database (Denmark)

David, Alexandre; Larsen, Kim Guldstrand; Legay, Axel

2015-01-01

-approximation technique. We can safely conclude that the system is schedulable for varying values of BCET. For the cases where deadlines are violated, we use polyhedra to try to confirm the witnesses. Our alternative method to confirm non-schedulability uses statistical model-checking (SMC) to generate counter...... and blocking times of tasks. Consequently, the method may falsely declare deadline violations that will never occur during execution. This paper is a continuation of previous work of the authors in applying extended timed automata model checking (using the tool UPPAAL) to obtain more exact schedulability...... analysis, here in the presence of non-deterministic computation times of tasks given by intervals [BCET,WCET]. Computation intervals with preemptive schedulers make the schedulability analysis of the resulting task model undecidable. Our contribution is to propose a combination of model checking techniques...

IFMIF Li target back-plate design integration and thermo-mechanical analysis

International Nuclear Information System (INIS)

Riccardi, B.; Roccella, S.; Micciche, G.

2006-01-01

The International Fusion Materials Irradiation Facility (IFMIF) is an accelerator-driven intense neutron source where fusion reactor candidate materials will be tested. The neutron flux is produced by means of a deuteron beam (current 250 mA, energy 40 MeV) that strikes a liquid lithium target circulating in a lithium loop. The support on which the liquid lithium flows, i.e. the back-plate, is the most heavily exposed component to neutron flux. A '' bayonet '' concept solution for the back-plate was proposed by ENEA with the objectives of improving the back-plate reliability and simplifying the remote handling procedures. On the base of this concept, a back-plate mock-up was fabricated and validated. Starting from the findings of the mock up design, a back-plate design integration exercise was carried out in order to check if the back-plate geometrical features are compatible with the target assembly and the Vertical Test Assemblies (VTA). The work carried out has demonstrated that even with the changes operated for the design integration (increase of in-plane dimensions and reduction of thickness) the bayonet concept is able to guarantee a tight connection to the target assembly. A thermo-mechanical analysis of the back-plate has been carried out by means of ABAQUS code. The thermal load used as input for the calculations, i.e. the neutron heat generation, has been estimated by means of Monte Carlo Mc-Delicious code. The two boundary constraint cases (full and minimum contact with target assembly) considered for each back-plate geometry option represent the extreme cases of the real operating condition of the plate. The influence of the contact heat exchange coefficient and the back-plate thickness has been also evaluated. For all these reasons, the results of the analysis can be considered as the domain of variability of the real working conditions. The results show that AISI 316L steel is not suitable as black-plate material: the stress induced in the plate, in

Remote preenrollment checking of consent forms to reduce nonconformity.

Science.gov (United States)

Journot, Valérie; Pérusat-Villetorte, Sophie; Bouyssou, Caroline; Couffin-Cadiergues, Sandrine; Tall, Aminata; Chêne, Geneviève

2013-01-01

In biomedical research, the signed consent form must be checked for compliance with regulatory requirements. Checking usually is performed on site, most frequently after a participant's final enrollment. We piloted a procedure for remote preenrollment consent forms checking. We applied it in five trials and assessed its efficiency to reduce form nonconformity before participant enrollment. Our clinical trials unit (CTU) routinely uses a consent form with an additional copy that contains a pattern that partially masks the participant's name and signature. After completion and signatures by the participant and investigator, this masked copy is faxed to the CTU for checking. In case of detected nonconformity, the CTU suspends the participant's enrollment until the form is brought into compliance. We checked nonconformities of consent forms both remotely before enrollment and on site in five trials conducted in our CTU. We tabulated the number and nature of nonconformities by location of detection: at the CTU or on site. We used these data for a pseudo before-and-after analysis and estimated the efficiency of this remote checking procedure in terms of reduction of nonconformities before enrollment as compared to the standard on-site checking procedure. We searched for nonconformity determinants among characteristics of trials, consent forms, investigator sites, and participants through multivariate logistic regression so as to identify opportunities for improvement in our procedure. Five trials, starting sequentially but running concurrently, with remote preenrollment and on-site checking of consent forms from 415 participants screened in 2006-2009 led to 518 consent forms checked; 94 nonconformities were detected in 75 forms, 75 (80%) remotely and 19 more (20%) on site. Nonconformities infrequently concerned dates of signatures (7%) and information about participants (12%). Most nonconformities dealt with investigator information (76%), primarily contact information

Spin Interactions and Cross-checks of Polarization in NH$_{3}$ Target

CERN Document Server

Kiselev, Yu; Doshita, N; Gautheron, F; Hess, Ch; Iwata, T; Koivuniemi, J; Kondo, K; Magnon, A; Mallot, G; Michigami, T; Meyer, W; Reicherz, G

2008-01-01

We study the magnetic structure of irradiated ammonia (NH$_{3}$) polarized by Dynamic Nuclear Polarization method at 0.2 K and at 2.5 T field. In this material, the electron spins, induced by ionizing radiation, couple $^{14}$N and $^{1}$H spins by the indirect spin-spin interaction. As a result, the local frequencies of $^{1}$H-spins are varied depending on $^{14}$N spin polarizations and lead to an asymmetry in the proton signal. This asymmetry allowes a good detection of $^{14}$N spins directly on the proton Larmor frequency. In the long COMPASS target at CERN, we use the cross-checks between spectral asymmetries and integral polarizations to decrease the relative error for longitudinal target polarizations up to $\\pm$2.0%.

A Design for an Orbital Assembly Facility for Complex Missions

Science.gov (United States)

Feast, S.; Bond, A.

A design is presented for an Operations Base Station (OBS) in low earth orbit that will function as an integral part of a space transportation system, enabling assembly and maintenance of a Cis-Lunar transportation infrastructure and integration of vehicles for other high energy space missions to be carried out. Construction of the OBS assumes the use of the SKYLON Single-Stage-to-Orbit (SSTO) spaceplane, which imposes design and assembly constraints due to its payload mass limits and payload bay dimensions. It is assumed that the space transport infrastructure and high mission energy vehicles would also make use of SKYLON to deploy standard transport equipment and stages bound by these same constraints. The OBS is therefore a highly modular arrangement, incorporating some of these other vehicle system elements in its layout design. Architecturally, the facilities of the OBS are centred around the Assembly Dock which is in the form of a large cylindrical spaceframe structure with two large doors on either end incorporating a skin of aluminised Mylar to enclose the dock. Longitudinal rails provide internal tether attachments to anchor vehicles and components while manipulators are used for the handling and assembling of vehicle structures. The exterior of the OBS houses the habitation modules for workforce and vehicle crews along with propellant farms and other operational facilities.

RCC-C: Design and construction rules for fuel assemblies of PWR nuclear power plants

International Nuclear Information System (INIS)

2015-01-01

The RCC-C code contains all the requirements for the design, fabrication and inspection of nuclear fuel assemblies and the different types of core components (rod cluster control assemblies, burnable poison rod assemblies, primary and secondary source assemblies and thimble plug assemblies). The design, fabrication and inspection rules defined in RCC-C leverage the results of the research and development work pioneered in France, Europe and worldwide, and which have been successfully used by industry to design and build nuclear fuel assemblies and incorporate the resulting feedback. The code's scope covers: fuel system design, especially for assemblies, the fuel rod and associated core components, the characteristics to be checked for products and parts, fabrication methods and associated inspection methods. The RCC-C code is used by the operator of the PWR nuclear power plants in France as a reference when sourcing fuel from the world's top two suppliers in the PWR market, given that the French operator is the world's largest buyer of PWR fuel. Fuel for EPR projects is manufactured according to the provisions of the RCC-C code. The code is available in French and English. The 2005 edition has been translated into Chinese. Contents of the 2015 edition of the RCC-C code: Chapter 1 - General provisions: 1.1 Purpose of the RCC-C, 1.2 Definitions, 1.3 Applicable standards, 1.4 Equipment subject to the RCC-C, 1.5 Management system, 1.6 Processing of non-conformances; Chapter 2 - Description of the equipment subject to the RCC-C: 2.1 Fuel assembly, 2.2 Core components; Chapter 3 - Design: Safety functions, operating functions and environment of fuel assemblies and core components, design and safety principles; Chapter 4 - Manufacturing: 4.1 Materials and part characteristics, 4.2 Assembly requirements, 4.3 Manufacturing and inspection processes, 4.4 Inspection methods, 4.5 Certification of NDT inspectors, 4.6 Characteristics to be inspected for the

The importance of drug checking outside the context of nightlife in Slovenia.

Science.gov (United States)

Sande, Matej; Šabić, Simona

2018-01-12

The main purpose of the research was to evaluate the implementation of the drug checking service in Slovenia and to obtain the opinion of users included in harm reduction programmes for high-risk drug users and of drug users in nightlife settings on drug checking, the reasons for drug checking, and their attitude towards adulterants in the drugs that they use. The two final unrepresentative research samples included 102 respondents from harm reduction programmes and 554 respondents from the online sample. The questionnaire was designed based on analysis of the interviews conducted with professionals from the programmes, who took part in the drug checking project, and based on previous research on drug use in nightlife. The main findings related to users' opinions on the drug checking service are that users from both samples perceive drug checking as a contribution to risk reduction and that they find providing information for them about the harmful adulterants and substances that they use very important. In addition, users from both samples considered accessibility of the drug checking service as very important and would be in favour of brief counselling at the collection of the drug sample. One of the salient differences between samples was that nightlife drug users found it more important to recognise substances in the drugs that they use. Drug users from two different samples attach a relatively high importance to the drug checking service, and they consider it to be a contribution to risk reduction. As well as drug users in nightlife settings, high-risk drug users also perceive the drug checking service to be important, which is relevant in the phase of planning drug checking services outside the context of nightlife and for the act of incorporating these services into contemporary harm reduction policy.

Pixel Detector Trial Assembly Test in the SR1 building

CERN Multimedia

D. Giugni

2004-01-01

During the last two months the Pixel group [LBL, Milan and Wuppertal] made a successful integration test on the mechanics of the barrel. The scope of the test was to qualify the integration procedures and the various assembling tools. The test took place in the clean room of the SR1 building at CERN, where the detector has been assembled around a dummy beam pipe made of Stainless Steel. The process is rather complex: the shells come in two parts and they have to be clamped together to get the full shell. This operation is carried out by a dedicated tool which is shown to the right in the picture below. The layer 1 shell is clamped around a "service" pipe that will be used for moving the full layer to the integration tool [ITT] which is visible on the left. View of the tools devoted to the Pixel barrel integration in the SR1 building Also visible in the picture is the global frame that is actually held by the tool. It will engage the layers sliding onto the rails. The first two layers are sequentially...

Influence of check dams on debris-flow run-out intensity

Directory of Open Access Journals (Sweden)

A. Remaître

2008-12-01

Full Text Available Debris flows are very dangerous phenomena claiming thousands of lives and millions of Euros each year over the world. Disaster mitigation includes non-structural (hazard mapping, insurance policies, active structural (drainage systems and passive structural (check dams, stilling basins countermeasures. Since over twenty years, many efforts are devoted by the scientific and engineering communities to the design of proper devices able to capture the debris-flow volume and/or break down the energy. If considerable theoretical and numerical work has been performed on the size, the shape and structure of check dams, allowing the definition of general design criteria, it is worth noting that less research has focused on the optimal location of these dams along the debris-flow pathway.

In this paper, a methodological framework is proposed to evaluate the influence of the number and the location of the check dams on the reduction of the debris-flow intensity (in term of flow thickness, flow velocity and volume. A debris-flow model is used to simulate the run-out of the debris flow. The model uses the Janbu force diagram to resolve the force equilibrium equations; a bingham fluid rheology is introduced and represents the resistance term. The model has been calibrated on two muddy debris-flow events that occurred in 1996 and 2003 at the Faucon watershed (South French Alps.

Influence of the check dams on the debris-flow intensity is quantified taking into account several check dams configurations (number and location as input geometrical parameters. Results indicate that debris-flow intensity is decreasing with the distance between the source area and the first check dams. The study demonstrates that a small number of check dams located near the source area may decrease substantially the debris-flow intensity on the alluvial fans.

Experimental check of the Gerasimov-Drell-Hearn sum rule for H1

International Nuclear Information System (INIS)

Dutz, H.; Drachenfels, W. von; Frommberger, F.; Hillert, W.; Klein, F.; Menze, D.; Rohlof, C.; Schoch, B.; Helbing, K.; Speckner, T.; Zeitler, G.; Anton, G.; Bock, A.; Godo, M.; Kiel, B.; Michel, T.; Naumann, J.; Krimmer, J.; Grabmayr, P.; Sauer, M.

2004-01-01

For the first time we checked the fundamental Gerasimov-Drell-Hearn (GDH) sum rule for the proton experimentally in the photon energy range from 0.2-2.9 GeV with the tagged photon facilities at MAMI (Mainz) and ELSA (Bonn). New data of the doubly polarized total cross section difference are presented in the energy range from 1.6 to 2.9 GeV. The contribution to the GDH integral from 0.2-2.9 GeV yields [254±5(stat)±12(syst)] μb with negative contributions in the Regge regime at photon energies above 2.1 GeV. This trend supports the validity of the GDH sum rule

Efficient Multi-Valued Bounded Model Checking for LTL over Quasi-Boolean Algebras

OpenAIRE

Andrade, Jefferson O.; Kameyama, Yukiyoshi

2012-01-01

Multi-valued Model Checking extends classical, two-valued model checking to multi-valued logic such as Quasi-Boolean logic. The added expressivity is useful in dealing with such concepts as incompleteness and uncertainty in target systems, while it comes with the cost of time and space. Chechik and others proposed an efficient reduction from multi-valued model checking problems to two-valued ones, but to the authors' knowledge, no study was done for multi-valued bounded model checking. In thi...

Assembly of a check-patterned CuS{sub x}–TiO{sub 2} film with an electron-rich pool and its application for the photoreduction of carbon dioxide to methane

Energy Technology Data Exchange (ETDEWEB)

Lee, Homin; Kwak, Byeong Sub [Department of Chemistry, College of Science, Yeungnam University, Gyeongsan, Gyeongbuk 38541 (Korea, Republic of); Park, No-Kuk [School of Chemical Engineering, Yeungnam University, Gyeongsan, Gyeongbuk 38541 (Korea, Republic of); Baek, Jeom-In [KEPCO Research Institute, Korea Electric Power Corporation, 105 Munji-ro, Yuseong-gu, Daejeon 34056 (Korea, Republic of); Ryu, Ho-Jung [Korea Institute of Energy Research, 152 Gajeong-ro, Yuseong-gu, Daejeon 34129 (Korea, Republic of); Kang, Misook, E-mail: mskang@ynu.ac.kr [Department of Chemistry, College of Science, Yeungnam University, Gyeongsan, Gyeongbuk 38541 (Korea, Republic of)

2017-01-30

Highlights: • A new check-patterned CuS{sub x}–TiO{sub 2} film was prepared by the squeeze printing method. • Significantly increased amounts of CO{sub 2} were adsorbed on the CuS{sub x}–TiO{sub 2} film. • High amounts of CH{sub 4} (53.2 μmolg{sub cat}{sup −1} L{sup −1}) were produced over the CuS{sub x}–TiO{sub 2} film. • An electron-rich pool was supposedly formed at the boundary between TiO{sub 2} and CuS{sub x}. - Abstract: A new check-patterned CuS{sub x}–TiO{sub 2} film was designed to improve the photoreduction of CO{sub 2} to CH{sub 4}. The check-patterned CuS{sub x}–TiO{sub 2} film with a 3D-network microstructure was fabricated by a facile squeeze method. The as-synthesized TiO{sub 2} and CuS{sub x} powders, as well as the patterned film, were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), UV–visible spectroscopy, cyclic voltammetry (CV), and photoluminescence (PL) spectroscopy, as well as photocurrent density and CO{sub 2} temperature-programmed desorption (TPD) measurements. Compared to pure CuS{sub x} and TiO{sub 2}, the check-patterned CuS{sub x}–TiO{sub 2} film exhibited significantly increased adsorption of CO{sub 2} on its networked microstructure, attributed to the enlarged interfaces between the microparticles. The check-patterned CuS{sub x}–TiO{sub 2} film exhibited superior photocatalytic behavior, with 53.2 μmolg{sub cat}{sup −1} L{sup −1} of CH{sub 4} produced after 8 h of reaction, whereas 18.1 and 7.3 μmolg{sub cat}{sup −1} L{sup −1} of CH{sub 4} were produced from pure TiO{sub 2} and CuS{sub x} films under the same reaction conditions, respectively. A model for enhanced photoactivity over the check-patterned CuS{sub x} − TiO{sub 2} film was proposed. Results indicated that the check-patterned CuS–TiO{sub 2} material is quite promising as a photocatalyst for the reduction of CO{sub 2} to CH{sub 4}.

Dielectrophoretic assembly of carbon nanotube devices

DEFF Research Database (Denmark)

Dimaki, Maria

The purpose of this project has been to assemble single-walled carbon nanotubes on electrodes at the tip of a biocompatible cantilever and use these for chemical species sensing in air and liquid, for example in order to measure the local activity from ion channels in the cell membrane....... The electrical resistance of carbon nanotubes has been shown to be extremely sensitive to gas molecules. Dielectrophoresis is a method capable of quickly attracting nanotubes on microelectrodes by using an electric field, thus enabling nanotube integration in microsystems. Dielectrophoresis offers also....... A model for the dielectrophoretic assembly of carbon nanotubes on microelectrodes was developed and several simulations were conducted using values from the available literature for the various key parameters. The model can give qualitative results regarding the parameters dominating the dielectrophoretic...

Controlled Synthesis of Nanowire Assemblies by Ion-Track Template Electrodeposition

OpenAIRE

Rauber, Markus

2012-01-01

The development of methods that allow the organization of nanostructures into integrated arrangements is crucial to realizing applications based on nanowires. Although various such methods exist, the direct synthesis of complex nanowire structures is one of the most suitable approaches for translating a large quantity of nanostructures into micro-/macroscale dimensions. In particular, three-dimensional (3-D) nanowire assemblies with a high integration level and adjustable connecti...

Efficient Multi-Valued Bounded Model Checking for LTL over Quasi-Boolean Algebras

Science.gov (United States)

Andrade, Jefferson O.; Kameyama, Yukiyoshi

Multi-valued Model Checking extends classical, two-valued model checking to multi-valued logic such as Quasi-Boolean logic. The added expressivity is useful in dealing with such concepts as incompleteness and uncertainty in target systems, while it comes with the cost of time and space. Chechik and others proposed an efficient reduction from multi-valued model checking problems to two-valued ones, but to the authors' knowledge, no study was done for multi-valued bounded model checking. In this paper, we propose a novel, efficient algorithm for multi-valued bounded model checking. A notable feature of our algorithm is that it is not based on reduction of multi-values into two-values; instead, it generates a single formula which represents multi-valuedness by a suitable encoding, and asks a standard SAT solver to check its satisfiability. Our experimental results show a significant improvement in the number of variables and clauses and also in execution time compared with the reduction-based one.

Mapsembler, targeted and micro assembly of large NGS datasets on a desktop computer

Directory of Open Access Journals (Sweden)

Peterlongo Pierre

2012-03-01

Full Text Available Abstract Background The analysis of next-generation sequencing data from large genomes is a timely research topic. Sequencers are producing billions of short sequence fragments from newly sequenced organisms. Computational methods for reconstructing whole genomes/transcriptomes (de novo assemblers are typically employed to process such data. However, these methods require large memory resources and computation time. Many basic biological questions could be answered targeting specific information in the reads, thus avoiding complete assembly. Results We present Mapsembler, an iterative micro and targeted assembler which processes large datasets of reads on commodity hardware. Mapsembler checks for the presence of given regions of interest that can be constructed from reads and builds a short assembly around it, either as a plain sequence or as a graph, showing contextual structure. We introduce new algorithms to retrieve approximate occurrences of a sequence from reads and construct an extension graph. Among other results presented in this paper, Mapsembler enabled to retrieve previously described human breast cancer candidate fusion genes, and to detect new ones not previously known. Conclusions Mapsembler is the first software that enables de novo discovery around a region of interest of repeats, SNPs, exon skipping, gene fusion, as well as other structural events, directly from raw sequencing reads. As indexing is localized, the memory footprint of Mapsembler is negligible. Mapsembler is released under the CeCILL license and can be freely downloaded from http://alcovna.genouest.org/mapsembler/.

Independent checks of linear accelerators equipped with multileaf collimators

International Nuclear Information System (INIS)

Pavlikova, I.; Ekendahl, D.; Horakova, I.

2005-01-01

National Radiation Protection Institute (NRPI) provides independent checks of therapeutic equipment as a part of state supervision. In the end of 2003, the audit was broaden for linear accelerators equipped with multileaf collimators (MLC). NRPI provides TLD postal audits and on-site independent checks. This contribution describes tests for multileaf collimators and intensity modulated radiation therapy (IMRT) technique that are accomplished within the independent on-site check of linear accelerators. The character and type of tests that are necessary to pursue for multileaf collimator depends on application technique. There are three basic application of the MLC. The first we call 'static MLC' and it serves for replacing conventional blocking or for adjusting the field shape to match the beam's-eye view projection of a planning target volume during an arc rotation of the x-ray beam. This procedure is called conformal radiotherapy. The most advanced technique with MLC is intensity modulated radiation therapy. The dose can be delivered to the patient with IMRT in various different ways: dynamic MLC, segmented MLC and IMRT arc therapy. Independent audits represent an important instrument of quality assurance. Methodology for independent check of static MLC was successfully verified on two types of accelerators: Varian and Elekta. Results from pilot measurements with dynamic MLC imply that the methodology is applicable for Varian accelerators. In the future, the experience with other types of linear accelerators will contribute to renovation, modification, and broaden independent checks methodology. (authors)

Main results of post-irradiation examinations of new-generation fuel assemblies VVER-1000

International Nuclear Information System (INIS)

Zvir, E.; Markov, D.; Polenok, V.; Zhitelev, V.; Kobylyansky, G.

2009-01-01

To increase the competitiveness of Russian nuclear fuel at the foreign market and to improve its technical and economic performance in order to provide a necessary level of safety, it is necessary to solve certain important tasks: Increase of fuel burn-up; Extension of operational lifetime of fuel assemblies and operational reliability of nuclear fuel; Introduction of cost-beneficial and flexible fuel cycles. Alternative fuel assemblies TVSA VVER-1000 and TVS-2 are used as a basis to optimize the nuclear fuel and develop advanced fuel cycles for nuclear power plants with VVER-1000 reactor types. Four fuel assemblies TVSA operated during 1 and up to 6 reactor cycles, reference fuel assembly TVS-2 operated during three reactor cycles and achieved an average fuel burnup of 48MW·day/kgU as well as failed fuel assembly TVS-2 operated during one cycle were examined at RIAR in recent years. The main objectives of these examinations were to obtain experimental data in support of operational integrity of products or to find out reasons of their failure. The performed post-irradiation examinations confirmed the operational integrity of alternative fuel assemblies TVSA including their geometrical stability up to the average fuel burnup of 55 MW·day/kgU over the fuel assembly (FA) (up to the maximal fuel burnup of ∼73 MW·day/kgU in fuel rods) and of TVS-2 up to the average fuel burnup of 48 MW·day/kgU over the fuel assembly. The changes introduced in the design of VVER-1000 fuel assembly during the development of alternative fuel assembly TVSA and TVS-2 did not make any negative effect on fuel rods. It was proved that causes of fuel rod failure were not related to design features of fuel assemblies. The design features and operating conditions of fuel assemblies under examinations are briefly described. Post-irradiation examinations proved the geometrical stability of fuel assemblies TVSA and TVS-2 under operation up to the fuel burnup of ∼50 MW day/kgU, as for the

Cuba: Multidimensional numerical integration library

Science.gov (United States)

Hahn, Thomas

2016-08-01

The Cuba library offers four independent routines for multidimensional numerical integration: Vegas, Suave, Divonne, and Cuhre. The four algorithms work by very different methods, and can integrate vector integrands and have very similar Fortran, C/C++, and Mathematica interfaces. Their invocation is very similar, making it easy to cross-check by substituting one method by another. For further safeguarding, the output is supplemented by a chi-square probability which quantifies the reliability of the error estimate.

Assembly factors for the membrane arm of human complex I.

Science.gov (United States)

Andrews, Byron; Carroll, Joe; Ding, Shujing; Fearnley, Ian M; Walker, John E

2013-11-19

Mitochondrial respiratory complex I is a product of both the nuclear and mitochondrial genomes. The integration of seven subunits encoded in mitochondrial DNA into the inner membrane, their association with 14 nuclear-encoded membrane subunits, the construction of the extrinsic arm from 23 additional nuclear-encoded proteins, iron-sulfur clusters, and flavin mononucleotide cofactor require the participation of assembly factors. Some are intrinsic to the complex, whereas others participate transiently. The suppression of the expression of the NDUFA11 subunit of complex I disrupted the assembly of the complex, and subcomplexes with masses of 550 and 815 kDa accumulated. Eight of the known extrinsic assembly factors plus a hydrophobic protein, C3orf1, were associated with the subcomplexes. The characteristics of C3orf1, of another assembly factor, TMEM126B, and of NDUFA11 suggest that they all participate in constructing the membrane arm of complex I.

Magnetic Check Valve

Science.gov (United States)

Morris, Brian G.; Bozeman, Richard J., Jr.

1994-01-01

Poppet in proposed check valve restored to closed condition by magnetic attraction instead of spring force. Oscillations suppressed, with consequent reduction of wear. Stationary magnetic disk mounted just upstream of poppet, also containing magnet. Valve body nonmagnetic. Forward pressure or flow would push poppet away from stationary magnetic disk so fluid flows easily around poppet. Stop in valve body prevents poppet from being swept away. When flow stopped or started to reverse, magnetic attraction draws poppet back to disk. Poppet then engages floating O-ring, thereby closing valve and preventing reverse flow. Floating O-ring facilitates sealing at low loads.

Member Checking: A Tool to Enhance Trustworthiness or Merely a Nod to Validation?

Science.gov (United States)

Birt, Linda; Scott, Suzanne; Cavers, Debbie; Campbell, Christine; Walter, Fiona

2016-06-22

The trustworthiness of results is the bedrock of high quality qualitative research. Member checking, also known as participant or respondent validation, is a technique for exploring the credibility of results. Data or results are returned to participants to check for accuracy and resonance with their experiences. Member checking is often mentioned as one in a list of validation techniques. This simplistic reporting might not acknowledge the value of using the method, nor its juxtaposition with the interpretative stance of qualitative research. In this commentary, we critique how member checking has been used in published research, before describing and evaluating an innovative in-depth member checking technique, Synthesized Member Checking. The method was used in a study with patients diagnosed with melanoma. Synthesized Member Checking addresses the co-constructed nature of knowledge by providing participants with the opportunity to engage with, and add to, interview and interpreted data, several months after their semi-structured interview. © The Author(s) 2016.

Employees are ambivalent about health checks in the occupational setting

NARCIS (Netherlands)

Damman, O.C.; van der Beek, A.J.; Timmermans, D.R.M.

2015-01-01

Background: Employees are increasingly provided with preventive health checks. However, participation rates are low and several ethical issues arise, such as a potential perceived threat to autonomy and privacy. Aims: To assess what employees think about preventive health checks in the occupational

Evaluation of Dosimetry Check software for IMRT patient-specific quality assurance.

Science.gov (United States)

Narayanasamy, Ganesh; Zalman, Travis; Ha, Chul S; Papanikolaou, Niko; Stathakis, Sotirios

2015-05-08

The purpose of this study is to evaluate the use of the Dosimetry Check system for patient-specific IMRT QA. Typical QA methods measure the dose in an array dosimeter surrounded by homogenous medium for which the treatment plan has been recomputed. With the Dosimetry Check system, fluence measurements acquired on a portal dosimeter is applied to the patient's CT scans. Instead of making dose comparisons in a plane, Dosimetry Check system produces isodose lines and dose-volume histograms based on the planning CT images. By exporting the dose distribution from the treatment planning system into the Dosimetry Check system, one is able to make a direct comparison between the calculated dose and the planned dose. The versatility of the software is evaluated with respect to the two IMRT techniques - step and shoot and volumetric arc therapy. The system analyzed measurements made using EPID, PTW seven29, and IBA MatriXX, and an intercomparison study was performed. Plans from patients previously treated at our institution with treated anatomical site on brain, head & neck, liver, lung, and prostate were analyzed using Dosimetry Check system for any anatomical site dependence. We have recommendations and possible precautions that may be necessary to ensure proper QA with the Dosimetry Check system.

Sequence assembly

DEFF Research Database (Denmark)

Scheibye-Alsing, Karsten; Hoffmann, S.; Frankel, Annett Maria

2009-01-01

Despite the rapidly increasing number of sequenced and re-sequenced genomes, many issues regarding the computational assembly of large-scale sequencing data have remain unresolved. Computational assembly is crucial in large genome projects as well for the evolving high-throughput technologies and...... in genomic DNA, highly expressed genes and alternative transcripts in EST sequences. We summarize existing comparisons of different assemblers and provide a detailed descriptions and directions for download of assembly programs at: http://genome.ku.dk/resources/assembly/methods.html....

First experiences with the LHC BLM sanity checks

OpenAIRE

Emery, J; Dehning, B; Effinger, E; Nordt, A; Sapinski, M G; Zamantzas, C

2010-01-01

The reliability concerns have driven the design of the Large Hardron Collider (LHC) Beam Loss Monitoring (BLM) system from the early stage of the studies up to the present commissioning and the latest development of diagnostic tools. To protect the system against non-conformities, new ways of automatic checking have been developed and implemented. These checks are regularly and systematically executed by the LHC operation team to ensure that the system status is after each test "as good as ne...

Grab Windows training opportunities; check CERN Windows roadmap!

CERN Multimedia

IT Department

2011-01-01

CERN Operating Systems and Information Services group (IT-OIS) actively monitors market trends to check how new software products correspond to CERN needs. In the Windows world, Windows 7 has been a big hit, with over 1500 Windows 7 PCs within less than a year since its support was introduced at CERN. No wonder: Windows XP is nearly 10 years old and is steadily approaching the end of its life-cycle. At CERN, support for Windows XP will stop at the end of December 2012. Compared to Vista, Windows 7 has the same basic hardware requirements, but offers higher performance, so the decision to upgrade is rather straightforward. CERN support for Vista will end in June 2011. In the world of Microsoft Office, version 2007 offers better integration with the central services than the older version 2003. Progressive upgrade from 2003 to 2007 is planned to finish in September 2011, but users are encouraged to pro-actively upgrade at their convenience. Please note that Office 2007 brings an important change in the area of ...

Most advanced HTP fuel assembly design for EPR

International Nuclear Information System (INIS)

Francillon, Eric; Kiehlmann, Horst-Dieter

2006-01-01

End 2003, the Finnish electricity utility Teollisuuden Voima Oy (TVO) signed the contract for building an EPR in Olkiluoto (Finland). Mid 2004, the French electricity utility EDF selected an EPR to be built in France. In 2005, Framatome ANP, an AREVA and Siemens company, announced that they will be pursuing a design certification in the U.S. The EPR development is based on the latest PWR product lines of former Framatome (N4) and Siemens Nuklear (Konvoi). As an introductory part, different aspects of the EPR core characteristics connected to fuel assembly design are presented. It includes means of ensuring reactivity control like hybrid AIC/B4C control rod absorbers and gadolinium as burnable absorber integrated in fuel rods, and specific options for in-core instrumentation, such as Aeroball type instrumentation. Then the design requirements for the EPR fuel assembly are presented in term of very high burnup capacity, rod cladding and fuel assembly reliability. Framatome ANP fuel assembly product characteristics meeting these requirements are then described. EPR fuel assembly design characteristics benefit from the experience feedback of the latest fuel assembly products designed within Framatome ANP, leading to resistance to assembly deformation, high fuel rod restraint and prevention of handling hazards. EPR fuel assembly design features the best components composing the cornerstones of the upgraded family of fuel assemblies that FRAMATOME ANP proposes today. This family is based on a set of common characteristics and associated features, which include the HMP grid as bottom end spacer, the MONOBLOC guide tube and the Robust FUELGUARD as lower tie plate, the use of the M5 Alloy, as cladding and structure material. This fully re-crystallized, ternary Zr-Nb-O alloy produces radically improved in-reactor corrosion, very low hydrogen uptake and growth and an excellent creep behavior, which are described there. EPR fuel assembly description also includes fuel rod

BWR 9 X 9 Fuel Assembly Thermal-Hydraulic Tests (2): Hydraulic Vibration Test

International Nuclear Information System (INIS)

Yoshiaki Tsukuda; Katsuichiro Kamimura; Toshiitsu Hattori; Akira Tanabe; Noboru Saito; Masahiko Warashina; Yuji Nishino

2002-01-01

Nuclear Power Engineering Corporation (NUPEC) conducted thermal-hydraulic projects for verification of thermal-hydraulic design reliability for BWR high-burnup 8 x 8 and 9 x 9 fuel assemblies, entrusted by the Ministry of Economy, Trade and Industry (METI). As a part of the NUPEC thermal-hydraulic projects, hydraulic vibration tests using full-scale test assemblies simulating 9 x 9 fuel assemblies were carried out to evaluate BWR fuel integrity. The test data were applied to development of a new correlation for the estimation of fuel rod vibration amplitude. (authors)

Integral data for fast reactors

International Nuclear Information System (INIS)

Collins, P.J.; Poenitz, W.P.; McFarlane, H.F.

1988-01-01

Requirements at Argonne National Laboratory to establish the best estimates and uncertainties for LMR design parameters have lead to an extensive evaluation of the available critical experiment database. Emphasis has been put upon selection of a wide range of cores, including both benchmark, assemblies covering a range of spectra and compositions and power reactor mock-up assemblies with diverse measured parameters. The integral measurements have been revised, where necessary, using the most recent reference data and a covariance matrix constructed. A sensitivity database has been calculated, embracing all parameters, which enables quantification of the relevance of the integral data to parameters calculated with ENDF/B-V.2 cross sections

SU-D-BRD-03: Improving Plan Quality with Automation of Treatment Plan Checks