WorldWideScience

Sample records for integrated sulphuric acid

  1. Modelling of temporal and spatial evolution of sulphur oxides and sulphuric acid under large, two-stroke marine engine-like conditions using integrated CFD-chemical kinetics

    DEFF Research Database (Denmark)

    Pang, Kar Mun; Karvounis, Nikolas; Walther, Jens Honore

    2017-01-01

    In this work, three-dimensional computational fluid dynamics (CFD) studies of sulphur oxides (SOx) andsulphuric acid (H2SO4) formation processes in a large, low speed two-stroke marine diesel engine are carriedout. The current numerical study aims to investigate the conversion of sulphuric dioxide...... that the flameimpinges at the cylinder liner near top dead centre. The gas is cooled rapidly by the wall temperatureand H2SO4 is produced in the region where the local temperature is less than 600 K. Based on the fluegas correlation, the acid dew point temperature is higher than the wall temperature, suggesting...

  2. A statistical proxy for sulphuric acid concentration

    Directory of Open Access Journals (Sweden)

    S. Mikkonen

    2011-11-01

    Full Text Available Gaseous sulphuric acid is a key precursor for new particle formation in the atmosphere. Previous experimental studies have confirmed a strong correlation between the number concentrations of freshly formed particles and the ambient concentrations of sulphuric acid. This study evaluates a body of experimental gas phase sulphuric acid concentrations, as measured by Chemical Ionization Mass Spectrometry (CIMS during six intensive measurement campaigns and one long-term observational period. The campaign datasets were measured in Hyytiälä, Finland, in 2003 and 2007, in San Pietro Capofiume, Italy, in 2009, in Melpitz, Germany, in 2008, in Atlanta, Georgia, USA, in 2002, and in Niwot Ridge, Colorado, USA, in 2007. The long term data were obtained in Hohenpeissenberg, Germany, during 1998 to 2000. The measured time series were used to construct proximity measures ("proxies" for sulphuric acid concentration by using statistical analysis methods. The objective of this study is to find a proxy for sulfuric acid that is valid in as many different atmospheric environments as possible. Our most accurate and universal formulation of the sulphuric acid concentration proxy uses global solar radiation, SO2 concentration, condensation sink and relative humidity as predictor variables, yielding a correlation measure (R of 0.87 between observed concentration and the proxy predictions. Interestingly, the role of the condensation sink in the proxy was only minor, since similarly accurate proxies could be constructed with global solar radiation and SO2 concentration alone. This could be attributed to SO2 being an indicator for anthropogenic pollution, including particulate and gaseous emissions which represent sinks for the OH radical that, in turn, is needed for the formation of sulphuric acid.

  3. Leaching of basic oxygen furnace sludge with sulphuric acid

    Directory of Open Access Journals (Sweden)

    Andrea Miškufová

    2010-03-01

    Full Text Available In this study the hydrometallurgical processing of BOF sludge in the sulphuric acid solutions under atmospheric pressureand temperatures up to 100 °C is investigated on a laboratory scale. The influence of sulphuric acid concentration, temperature, timeand liquid to solid ratio (L:S on the leaching process was studied. The main aim of this study was to determine optimal conditions whenthe maximum amount of zinc passes into the solution.

  4. Ozonation of Sulfur Dioxide in Sulphuric Acid Solution

    Institute of Scientific and Technical Information of China (English)

    LIU Limei; ZHANG Shuting; L(U) Xuebin; YU Xiaoyan; ZHI Suli

    2013-01-01

    In this study,the oxidation rates of sulfur dioxide (SO2) in sulphuric acid solution by ozone and oxygen were compared,and the oxidation mechanism of ozone on SO2 was investigated.The results showed that the oxidation-reduction potential of the acidic solution was enhanced,the transformation rate of sulfuric acid to sulphuric acid was increased and the absorption driving force was improved in the presence of ozone.By comparing the amount of sulfate ions measured in the experiments and the theoretical amount of sulfate ions calculated from the amount of ozone consumed in the reaction,it can be confirmed that oxygen free radicals from dissociation of ozone are reactive as an efficient oxidant and oxygen from ozone generator participates in the reaction with SO2.0.602tmol of effective oxygen was introduced into the reaction by one mole of ozone in 10.15 min at sulphuric acid concentration of 3% (by mass),SO2 concentration of 1.33% (by volume) and oxygen flow rate of 1.5 L·min-1 from ozone generator.

  5. Microbiological transformations of phosphorus and sulphur compounds in acid soils

    Directory of Open Access Journals (Sweden)

    Stamenov Dragana

    2012-01-01

    Full Text Available The dynamics of phosphorus and sulphur in soil is closely related to the dynamics of the biological cycle in which microorganisms play a central role. There is not much microbiological activity in acid soils because aerobes are scarce, rhizosphere is restricted to the shallow surface layer, and the biomass of microorganisms decreases with higher acidity. The aim of the research was to investigate the number of microorganisms, which decompose organic and inorganic phosphorus compounds and organic sulphur compounds in calcocambisol, luvisol, and pseudogley. The following parameters were determined in the soil samples: pH in H2O and in 1MKCl; the content of CaCO3 (%; humus content (%, nitrogen content (%; the content of physiologically active phosphorus and potassium (mg P2O5/100g of soil; mg K2O/100g of soil. The number of microorganisms was determined by the method of agar plates on appropriate nutrient media: the number of microorganisms solubilizing phosphates on a medium by Muramcov; the number of microorganisms that decompose organic phosphorus compounds on a medium with lecithin; and the number of microorganisms that transform organic sulphur compounds on a medium by Baar. All three types of soil are acid non-carbonate soils with a low level of available phosphorus and a more favorable amount of potassium, nitrogen, and humus. The largest number of bacteria, which transform organic phosphorus compounds, was found in calcocambisol. The largest number of phosphate solubilizing bacteria was recorded in pseudogley, whereas the largest number of phosphate solubilizing fungi was recorded in calcocambisol. The largest number of bacteria, which transform organic sulphur compounds, was recorded in pseudogley.

  6. Intensification of zinc dissolution process in sulphuric acid

    Directory of Open Access Journals (Sweden)

    Stanojević D.

    2005-01-01

    Full Text Available Many high purity salts are produced by dissolving pure metal in non-oxidizing mineral acids. If hydrogen overpotential on the given metal is high, then the rate of overall process is defined by reaction of hydrogen ion reduction. This study investigated the possibility of accelerated dissolving of metal zinc in sulphuric acid by introducing copper cathode on which evolving hydrogen is much easier than on zinc. It was found out that the acceleration of zinc dissolving is possible and, at constant surface of copper cathode depends on the quality of electrical contact between copper electrode and zinc.

  7. Aerosol dynamics simulations on the connection of sulphuric acid and new particle formation

    Directory of Open Access Journals (Sweden)

    S.-L. Sihto

    2008-06-01

    Full Text Available We have performed a series of simulations with an aerosol dynamics box model to study the connection between new particle formation and sulphuric acid concentration. For nucleation either activation mechanism with a linear dependence on the sulphuric acid concentration or ternary H2O-H2SO4-NH3 nucleation was assumed. We investigated the factors that affect the sulphuric acid dependence during the early stages of particle growth, and tried to find conditions which would yield the linear dependence between the particle number concentration at 3–6 nm and sulphuric acid, as observed in field experiments. The simulations showed that the correlation with sulphuric acid may change during the growth from nucleation size to 3–6 nm size range, the main reason being the size dependent growth rate between 1 and 3 nm. In addition, the assumed size for the nucleated clusters had a crucial impact on the sulphuric acid dependence at 3 nm. The simulations yielded a linear dependence between the particle number concentration at 3 nm and sulphuric acid, when a low saturation vapour pressure for the condensable organic vapour was assumed, or when nucleation took place at ~2 nm instead of ~1 nm. Comparison of results with activation and ternary nucleation showed that ternary nucleation cannot explain the experimentally observed linear or square dependence on sulphuric acid.

  8. Preparation of Cs-Rb-V series sulphuric acid catalyst

    Institute of Scientific and Technical Information of China (English)

    陈振兴; 杨刚; 叶华

    2001-01-01

    Cs-Rb-V series low temperature sulphuric acid catalyst was prepared for the first time by using carbonized mother liquor containing alkali-metal salts. The results show that the conversion of SO2 on catalyst prepared directly with carbonized mother liquor could reach to 24.8% at 410℃. If n(Na)/n(V) was adjusted properly, the conversion of SO2 could be increased to 35.6% at 410℃. Refined carbonized mother liquor could make the catalytic activity even higher at low temperature, the conversion of SO2 could be increased to 36.65% at 410℃. The catalyst was examined with differential thermal analysis. It was found that both endothermic peaks and exothermic peaks of catalyst shifted forward obviously and the catalyst possessed higher activity at low temperature.

  9. Method of removing sulphur and acid compounds from gasoline

    Energy Technology Data Exchange (ETDEWEB)

    Bilokur, V.F.; Selezhev, N.I.; Starkov, N.M.; Zhordochkin, N.A.

    1980-02-12

    A method of removing sulphur and acid compounds from gasoline is proposed. In order to increase the degree of purification, maintain continuity of the process and eliminate production waste, the gasoline is washed with water with subsequent treatment with 25 percent aqueous solution of monoethanol amine (I). With rewashing using water, the relative ratios are for gasoline (solution I 0.5:1-1:1 and gasoline) and water 1:0.8-1:1. After purification I is regenerated and circulated, and gasoline impurities not removed in the regeneration process are adsorbed by activated charcoal from a flow of regenerated I. The base gasoline is sent to a washing column where continuous removal of hydrogen soluble impurities takes place. It is settled in a settling tank and sent to the pump absorber intake line. Solution I is sent there. The mixture is sent to the absorber (temperature 35-45 degrees C, pressure 4-6 atm) where a process of absorption of sulphur and acid compounds takes place and is then sent to the settling tank in which rapid separation of phases occurs to the bottom the saturated absorbent, to the top the purified gasoline. The latter is sent to be washed by water, and the absorbent is sent for desorption to the desorber (temperature towards the top 102-105 degrees C, bottom 112-115 degrees C, pressure 0.7 atm). The temperature of water washing is 30-50 degrees C. After purification this method the gasoline contains 0.2-0.25 percent total S, does not contain H/sub 2/S and features a K. Ch. (mg KON/100 ml gasoline) of approximately 0.04-0.05.

  10. Morphology and evolution of sulphuric acid caves in South Italy

    Science.gov (United States)

    D'Angeli, Ilenia M.; De Waele, Jo; Galdenzi, Sandro; Madonia, Giuliana; Parise, Mario; Vattano, Marco

    2016-04-01

    Sulphuric acid speleogenesis (SAS) related to the upwelling of acid water enriched in H2S and CO2 represents an unusual way of cave development. Since meteoric infiltration waters are not necessarily involved in speleogenesis, caves can form without the typical associated karst expressions (i.e. dolines) at the surface. The main mechanism of sulphuric acid dissolution is the oxidation of H2S (Jones et al., 2015) which can be amplified by bacterial mediation (Engel et al., 2004). In these conditions, carbonate dissolution associated with gypsum replacement, is generally believed to be faster than the normal epigenic one (De Waele et al., 2016). In Italy several SAS caves have been identified, but only few systems have been studied in detail: Frasassi and Acquasanta Terme (Marche)(Galdenzi et al., 2010), Monte Cucco (Umbria) (Galdenzi & Menichetti, 1995), and Montecchio (Tuscany) (Piccini et al., 2015). Other preliminary studies have been carried out in Calabria (Galdenzi, 2007) and Sicily (De Waele et al., 2016). Several less studied SAS cave systems located in South Italy, and in particular in Apulia (Santa Cesarea Terme), Sicily (Acqua Fitusa, Acqua Mintina) and Calabria (Mt. Sellaro and Cassano allo Ionio) have been selected in the framework of a PhD thesis on SAS caves and their speleogenesis. Using both limestone tablet weight loss (Galdenzi et al., 2012) and micro erosion meter (MEM) (Furlani et al., 2010) methods the dissolution rate above and under water in the caves will be quantified. Geomorphological observations, landscape analysis using GIS tools, and the analysis of gypsum and other secondary minerals (alunite and jarosite) (stable isotopes and dating) will help to reconstruct the speleogenetic stages of cave formation. Preliminary microbiological analysis will determine the microbial diversity and ecology in the biofilms. References Engel S.A., Stern L.A., Bennett P.C., 2004 - Microbial contributions to cave formation: New insight into sulfuric acid

  11. Comparison of the SAWNUC model with CLOUD measurements of sulphuric acid-water nucleation

    Science.gov (United States)

    Ehrhart, Sebastian; Ickes, Luisa; Almeida, Joao; Amorim, Antonio; Barmet, Peter; Bianchi, Federico; Dommen, Josef; Dunne, Eimear M.; Duplissy, Jonathan; Franchin, Alessandro; Kangasluoma, Juha; Kirkby, Jasper; Kürten, Andreas; Kupc, Agnieszka; Lehtipalo, Katrianne; Nieminen, Tuomo; Riccobono, Francesco; Rondo, Linda; Schobesberger, Siegfried; Steiner, Gerhard; Tomé, António; Wimmer, Daniela; Baltensperger, Urs; Wagner, Paul E.; Curtius, Joachim

    2016-10-01

    Binary nucleation of sulphuric acid-water particles is expected to be an important process in the free troposphere at low temperatures. SAWNUC (Sulphuric Acid Water Nucleation) is a model of binary nucleation that is based on laboratory measurements of the binding energies of sulphuric acid and water in charged and neutral clusters. Predictions of SAWNUC are compared for the first time comprehensively with experimental binary nucleation data from the CLOUD chamber at European Organization for Nuclear Research. The experimental measurements span a temperature range of 208-292 K, sulphuric acid concentrations from 1·106 to 1·109 cm-3, and distinguish between ion-induced and neutral nucleation. Good agreement, within a factor of 5, is found between the experimental and modeled formation rates for ion-induced nucleation at 278 K and below and for neutral nucleation at 208 and 223 K. Differences at warm temperatures are attributed to ammonia contamination which was indicated by the presence of ammonia-sulphuric acid clusters, detected by an Atmospheric Pressure Interface Time of Flight (APi-TOF) mass spectrometer. APi-TOF measurements of the sulphuric acid ion cluster distributions ((H2SO4)i·HSO4- with i = 0, 1, ..., 10) show qualitative agreement with the SAWNUC ion cluster distributions. Remaining differences between the measured and modeled distributions are most likely due to fragmentation in the APi-TOF. The CLOUD results are in good agreement with previously measured cluster binding energies and show the SAWNUC model to be a good representation of ion-induced and neutral binary nucleation of sulphuric acid-water clusters in the middle and upper troposphere.

  12. Leaching of vanadium from sulphuric acid manufacture spent catalysts

    Directory of Open Access Journals (Sweden)

    García, Diego Juan

    2001-02-01

    Full Text Available Recovery of vanadium contained in spent catalysts from the manufacture of sulphuric acid has been studied in this work, resulting in an industrial multistage process for the treatment of them avoiding direct deposition or dumping. Characterization of supplied spent catalysts samples, confirmed vanadium levels showed in the literature. The study of variables influencing leaching process: type of leaching agent, leaching agent concentration, S/L ratio, stirring speed and temperature, allows to fix the most advantageous conditions using industrial application criterion and verifying that the process is difusión controlled. The work is completed by developing an industrial leaching cycle simulation with the aim of reproducing real performance of spent catalyst, proposing operating conditions, and verifying the non-toxic character of the final residue obtained.

    En el presente trabajo se ha estudiado la recuperación del vanadio contenido en los catalizadores agotados procedentes de la fabricación del ácido sulfúrico, planteando un proceso industrial multietapa para el tratamiento de estos residuos, evitando su deposición o vertido directos. La caracterización de las muestras de catalizadores agotados disponibles confirmó los valores encontrados en la bibliografía. Se estudiaron las variables que influyen en el proceso de lixiviación (tipo de agente de lixiviación y concentración del mismo, relación S/L, velocidad de agitación y temperatura definiendo las condiciones más adecuadas desde el punto de vista industrial y verificando que el proceso está controlado por mecanismos difusionales. El trabajo se completa con la simulación de un ciclo industrial de lavado del catalizador y la verificación de la nula toxicidad de los lixiviados obtenidos por degradación del residuo final. 24 Aplicación de la resistencia de ruido al estudio de pinturas ricas en zinc Noise resistance applied to the study of zinc rich paints

  13. Atmospheric sulphuric acid and neutral cluster measurements using CI-APi-TOF

    Directory of Open Access Journals (Sweden)

    T. Jokinen

    2011-12-01

    Full Text Available The first ambient measurements using nitrate ion based Chemical Ionization with the Atmospheric Pressure interface Time-Of-Flight mass spectrometer (CI-APi-TOF for sulphuric acid and neutral cluster detection are presented. We have found CI-APi-TOF a highly stable and sensitive tool for molecular sulphuric acid detection. The lowest limit of detection for sulphuric acid was determined to be 3 × 104 molecules cm−3 for two hour averaging. Signals from sulphuric acid clusters up to tetramer accompanied by ammonia were also obtained but these were found to result from naturally charged clusters formed by ion induced clustering in the atmosphere during nucleation. Opposite to earlier studies with cluster mass spectrometers, we had no indication of neutral clusters. The reason is either less efficient charging of clusters in comparison to molecular sulphuric acid, or in low concentration of neutral clusters at our measurement site during these particular nucleation events. We show that utilizing high resolution mass spectrometry is crucial in separating the weak sulfuric acid cluster signal from the other compounds.

  14. Atmospheric sulphuric acid and neutral cluster measurements using CI-APi-TOF

    Directory of Open Access Journals (Sweden)

    T. Jokinen

    2012-05-01

    Full Text Available The first ambient measurements using nitrate ion based Chemical Ionization with the Atmospheric Pressure interface Time-Of-Flight mass spectrometer (CI-APi-TOF for sulphuric acid and neutral cluster detection are presented. We have found CI-APi-TOF a highly stable and sensitive tool for molecular sulphuric acid detection. The lowest limit of detection for sulphuric acid was determined to be 3.6 × 104 molecules cm−3 for 15 min averaging. Signals from sulphuric acid clusters up to tetramer containing ammonia were also obtained but these were found to result from naturally charged clusters formed by ion induced clustering in the atmosphere during nucleation. Opposite to earlier studies with cluster mass spectrometers, we had no indication of neutral clusters. The reason is either less efficient charging of clusters in comparison to molecular sulphuric acid, or the low concentration of neutral clusters at our measurement site during these particular nucleation events. We show that utilizing high resolution mass spectrometry is crucial in separating the weak sulfuric acid cluster signal from other compounds.

  15. Microbial ecology of a novel sulphur cycling consortia from AMD: implications for acid generation

    Science.gov (United States)

    Loiselle, L. M.; Norlund, K. L.; Hitchcock, A. P.; Warren, L. A.

    2009-05-01

    Recent work1 identified a novel microbial consortia consisting of two bacterial strains common to acid mine drainage (AMD) environments (autotrophic sulphur oxidizer Acidithiobacillus ferrooxidans and heterotrophic Acidiphilium spp.) in an environmental enrichment from a mine tailings lake. The two strains showed a specific spatial arrangement within an EPS macrostructure or "pod" allowing linked metabolic redox cycling of sulphur. Sulphur species characterisation of the pods using scanning transmission X-ray microscopy (STXM) indicated that autotrophic tetrathionate disproportionation by A. ferrooxidans producing colloidal elemental sulphur (S0) is coupled to heterotrophic S0 reduction by Acidiphilium spp. Geochemical modelling of the microbial sulphur reactions indicated that if they are widespread in AMD environments, then global AMD-driven CO2 liberation from mineral weathering have been overestimated by 40-90%1. Given the common co-occurrence of these two bacteria in AMD settings, the purpose of this study was to evaluate if these pods could be induced in the laboratory by pure strains and if so, whether their combined sulphur geochemistry mimicked the previous findings. Laboratory batch experiments assessed the development of pods with pure strain type cultures (A. ferrooxidans ATCC 19859 with mixotroph Acidiphilium acidophilum ATCC 738 or strict heterotroph Acp. cryptum ATCC 2158) using fluorescent in situ hybridization (FISH) imaging. The microbial sulphur geochemistry was characterized under autotrophic conditions identical to those used with the environmental AMD enrichment in which the pods were discovered. Results showed that the combined pure strain A. ferrooxidans and Acp. acidophilum form pods identical in structure to the AMD enrichment. To test the hypothesis that these pods form for mutual metabolic benefit, experiments were performed amending pure strain and AMD enrichment bacterial treatments with organic carbon and/or additional sulphur to

  16. A procedure for the quantitative analysis of the sulphur amino acids of rat tissues.

    Science.gov (United States)

    Gaitonde, M K; Gaull, G E

    1967-03-01

    1. A method is described for the quantitative separation of the sulphur compounds in a single sample of tissue by passing an extract through a serial assembly of ion-exchange resins in the order: Dowex 2 (Cl(-) form), Dowex 1 (CO(3) (2-) form), Amberlite CG-50 (H(+) form) and Zeo-Karb 225 (H(+) form). 2. Groups of sulphur amino acids were eluted separately from each column; the recovery of sulphur compounds after their labelling with (35)S in vivo by injection of l-[(35)S]-methionine was 91-106%. Individual sulphur compounds were further resolved by one-dimensional or two-dimensional paper chromatography. 3. Evidence is presented on the occurrence of S-adenosylmethionine and S-adenosylhomocysteine in rat liver and brain. Rat liver and brain contained 83.6 and 31.4mmu-moles/g. respectively of S-adenosylmethionine.

  17. Biofilter for generation of concentrated sulphuric acid from H2S.

    Science.gov (United States)

    Rabbani, K A; Charles, W; Kayaalp, A; Cord-Ruwisch, R; Ho, G

    2016-08-01

    Biofilters are used for the conversion of odorous hydrogen sulphide to odourless sulphate in wastewater treatment plants under the right conditions of moisture and pH. One of the consequences of maintaining the suitable pH and moisture content is the production of large volumes of weakly acidic leachate. This paper presents a biofilter with a maximum H2S elimination capacity of 16.3 g m(-3) h(-1) and removal efficiency greater than 95 % which produces small volumes (1 mL of solution L(-1) of reactor day(-1)) of sulphuric acid with a concentration greater than 5.5 M after 150 days of continuous operation. The concentrated sulphuric acid was produced by intermittently trickling a minimum amount of nutrient solution down the upflow biofilter which created a moisture and pH gradient within the biofilter resulting in an environment at the top for the bacterial conversion of H2S, while sulphuric acid was accumulated at the base. Genetic diversity profiling of samples taken from different sections of the biofilter confirms that the upper sections of the biofilter had the best environment for the bacteria to convert H2S to sulphate. The formation of concentrated sulphuric acid presents an opportunity for the recovery of sulphur from the waste stream as a usable product.

  18. An isotopic analysis of ionising radiation as a source of sulphuric acid

    Directory of Open Access Journals (Sweden)

    M. B. Enghoff

    2012-06-01

    Full Text Available Sulphuric acid is an important factor in aerosol nucleation and growth. It has been shown that ions enhance the formation of sulphuric acid aerosols, but the exact mechanism has remained undetermined. Furthermore some studies have found a deficiency in the sulphuric acid budget, suggesting a missing source. In this study the production of sulphuric acid from SO2 through a number of different pathways is investigated. The production methods are standard gas phase oxidation by OH radicals produced by ozone photolysis with UV light, liquid phase oxidation by ozone, and gas phase oxidation initiated by gamma rays. The distributions of stable sulphur isotopes in the products and substrate were measured using isotope ratio mass spectrometry. All methods produced sulphate enriched in 34S and we find an enrichment factor (δ34S of 8.7 ± 0.4‰ (1 standard deviation for the UV-initiated OH reaction. Only UV light (Hg emission at 253.65 nm produced a clear non-mass-dependent excess of 33S. The pattern of isotopic enrichment produced by gamma rays is similar, but not equal, to that produced by aqueous oxidation of SO2 by ozone. This, combined with the relative yields of the experiments, suggests a mechanism in which ionising radiation may lead to hydrated ion clusters that serve as nanoreactors for S(IV to S(VI conversion.

  19. An isotope view on ionising radiation as a source of sulphuric acid

    Directory of Open Access Journals (Sweden)

    M. B. Enghoff

    2012-02-01

    Full Text Available Sulphuric acid is an important factor in aerosol nucleation and growth. It has been shown that ions enhance the formation of sulphuric acid aerosols, but the exact mechanism has remained undetermined. Furthermore some studies have found a deficiency in the sulphuric acid budget, suggesting a missing source. In this study the production of sulphuric acid from SO2 through a number of different pathways is investigated. The production methods are standard gas phase oxidation by OH radicals produced by ozone photolysis with UV light, liquid phase oxidation by ozone, and gas phase oxidation initiated by gamma rays. The distributions of stable sulphur isotopes in the products and substrate were measured using isotope ratio mass spectrometry. All methods produced sulphate enriched in 34S and we find a δ34S value of 8.7 ± 0.4‰ (1 standard deviation for the UV-initiated OH reaction. Only UV light (Hg emission at 253.65 nm produced a clear non-mass-dependent excess of 33S. The pattern of isotopic enrichment produced by gamma rays is similar, but not equal, to that produced by aqueous oxidation of SO2 by ozone. This, combined with the relative yields of the experiments, suggests a mechanism in which ionising radiation may lead to hydrated ion clusters that serve as nanoreactors for S(IV to S(VI conversion.

  20. Irreversible loss of ice nucleation active sites in mineral dust particles caused by sulphuric acid condensation

    Directory of Open Access Journals (Sweden)

    R. C. Sullivan

    2010-07-01

    Full Text Available During the FROST-2 (FReezing Of duST measurement campaign conducted at the Leipzig Aerosol Cloud Interaction Simulator (LACIS, we investigated changes in the ice nucleation properties of 300 nm Arizona test dust mineral particles following thermochemical processing by varying amounts and combinations of exposure to sulphuric acid vapour, ammonia gas, water vapour, and heat. The processed aerosol's heterogeneous ice nucleation properties were determined in both the water subsaturated and supersaturated humidity regimes at −30 °C and −25 °C using Colorado State University's continuous flow diffusion chamber. The amount of sulphuric acid coating material was estimated by an aerosol mass spectrometer and from CCN-derived hygroscopicity measurements. The condensation of sulphuric acid decreased the dust particles' ice nucleation ability in proportion to the amount of sulphuric acid added. Heating the coated particles in a thermodenuder at 250 °C – intended to evaporate the sulphuric acid coating – reduced their freezing ability even further. We attribute this behaviour to accelerated acid digestion of ice active surface sites by heat. Exposing sulphuric acid coated dust to ammonia gas produced particles with similarly poor freezing potential; however a portion of their ice nucleation ability could be restored after heating in the thermodenuder. In no case did any combination of thermochemical treatments increase the ice nucleation ability of the coated mineral dust particles compared to unprocessed dust. These first measurements of the effect of identical chemical processing of dust particles on their ice nucleation ability in both water subsaturated and mixed-phase supersaturated cloud conditions revealed that ice nucleation was more sensitive to all coating treatments in the water subsaturated regime. The results clearly indicate irreversible impairment of ice nucleation activity in both regimes after condensation of concentrated

  1. Atmospheric sulphuric acid and aerosol formation: implications from atmospheric measurements for nucleation and early growth mechanisms

    Directory of Open Access Journals (Sweden)

    S.-L. Sihto

    2006-01-01

    Full Text Available We have investigated the formation and early growth of atmospheric secondary aerosol particles building on atmospheric measurements. The measurements were part of the QUEST 2 campaign which took place in spring 2003 in Hyytiälä (Finland. During the campaign numerous aerosol particle formation events occurred of which 15 were accompanied by gaseous sulphuric acid measurements. Our detailed analysis of these 15 events is focussed on nucleation and early growth (to a diameter of 3 nm of fresh particles. It revealed that new particle formation seems to be a function of the gaseous sulphuric acid concentration to the power from one to two when the time delay between the sulphuric acid and particle number concentration is taken into account. From the time delay the growth rates of freshly nucleated particles from 1 nm to 3 nm were determined. The mean growth rate was 1.2 nm/h and it was clearly correlated with the gaseous sulphuric acid concentration. We tested two nucleation mechanisms – recently proposed cluster activation and kinetic type nucleation – as possible candidates to explain the observed dependences, and determined experimental nucleation coefficients. We found that some events are dominated by the activation mechanism and some by the kinetic mechanism. Inferred coefficients for the two nucleation mechanisms are the same order of magnitude as chemical reaction coefficients in the gas phase and they correlate with the product of gaseous sulphuric acid and ammonia concentrations. This indicates that besides gaseous sulphuric acid also ammonia has a role in nucleation.

  2. Investigating the significance of zero-point motion in small molecular clusters of sulphuric acid and water

    Energy Technology Data Exchange (ETDEWEB)

    Stinson, Jake L., E-mail: j.stinson@ucl.ac.uk; Ford, Ian J. [Department of Physics and Astronomy and London Centre for Nanotechnology, University College London, Gower Street, London WC1E 6BT (United Kingdom); Kathmann, Shawn M. [Physical Sciences Division, Pacific Northwest National Laboratory, Richland, Washington 99352 (United States)

    2014-01-14

    The nucleation of particles from trace gases in the atmosphere is an important source of cloud condensation nuclei, and these are vital for the formation of clouds in view of the high supersaturations required for homogeneous water droplet nucleation. The methods of quantum chemistry have increasingly been employed to model nucleation due to their high accuracy and efficiency in calculating configurational energies; and nucleation rates can be obtained from the associated free energies of particle formation. However, even in such advanced approaches, it is typically assumed that the nuclei have a classical nature, which is questionable for some systems. The importance of zero-point motion (also known as quantum nuclear dynamics) in modelling small clusters of sulphuric acid and water is tested here using the path integral molecular dynamics method at the density functional level of theory. The general effect of zero-point motion is to distort the mean structure slightly, and to promote the extent of proton transfer with respect to classical behaviour. In a particular configuration of one sulphuric acid molecule with three waters, the range of positions explored by a proton between a sulphuric acid and a water molecule at 300 K (a broad range in contrast to the confinement suggested by geometry optimisation at 0 K) is clearly affected by the inclusion of zero point motion, and similar effects are observed for other configurations.

  3. An analytical procedure for determination of sulphur species and isotopes in boreal acid sulphate soils and sediments

    Directory of Open Access Journals (Sweden)

    K. BACKLUND

    2008-12-01

    Full Text Available An analytical scheme suitable for boreal acid sulphate (AS soils and sediments was developed on the basis of existing methods. The presented procedure can be used to quantify and discriminate among acid volatile sulphide, cold chromium reducible sulphur, hot chromium reducible sulphur, elemental sulphur, sulphate sulphur, organic sulphur, total reducible sulphur and total sulphur. The sulphur fractions are recovered as either Ag2S or BaSO4 precipitates and can further be used for isotope analysis. Overlaps between sulphur species are common during speciation, and must be minimized. Some of these overlaps are caused by poor sampling and storage, inappropriate conditions during the distillation, or natural variations in the sample (e.g. Fe3+ interference and grain size. The procedural impact was determined by conducting tests on both artificial and natural samples containing one or several sulphur species. The method is applied on reduced sediment from an AS soil locality (Överpurmo and a brackish lake (Larsmo Lake in western Finland and the results, including S-isotopes, are discussed.;

  4. Enhancement of the ferromagnetic order of graphite after sulphuric acid treatment

    OpenAIRE

    Barzola-Quiquia, J.; Böhlmann, W.; Esquinazi, P.; Schadewitz, A.; Ballestar, A.; Dusari, S.; Schultze-Nobre, L.; Kersting, B.

    2011-01-01

    We have studied the changes in the ferromagnetic behavior of graphite powder and graphite flakes after treatment with diluted sulphuric acid. We show that this kind of acid treatment enhances substantially the ferromagnetic magnetization of virgin graphite micrometer size powder as well as in graphite flakes. The anisotropic magnetoresistance (AMR) amplitude at 300 K measured in a micrometer size thin graphite flake after acid treatment reaches values comparable to polycrystalline cobalt.

  5. In-situ Spectroscopic Studies and Modelling of Crystallization Processes of Sulphuric Acid Catalysts

    DEFF Research Database (Denmark)

    Oehlers, C.; Fehrmann, Rasmus; Masters, Stephen Grenville

    1996-01-01

    Deactivation of commercial and prototype sulphuric acid catalysts has been investigated in-situ by ESR spectroscopy. The influence of support pore structure,and the chemical composition of the catalyst and the gas phase was dicussed.A statistical lattice model was applied to describe...

  6. Ergo betters estimates after shaky first years. [Recovery of gold, uranium and sulphuric acid

    Energy Technology Data Exchange (ETDEWEB)

    1982-05-20

    Having completed its fourth year of full operation, East Rand Gold and Uranium (ERGO) has established itself as a succesful low-cost gold producer. The recovering of gold, uranium and sulphuric acid from some old slimes dams has beaten its production estimates for 1981 till the end of March 1982. Overall Ergo has settled down well from its first years of production.

  7. Comparison of the SAWNUC model with CLOUD measurements of sulphuric acid-water nucleation

    CERN Document Server

    Ehrhart, Sebastian; Almeida, Joao; Amorim, Antonio; Barmet, Peter; Bianchi, Federico; Dommen, Josef; Dunne, Eimear M; Duplissy, Jonathan; Franchin, Alessandro; Kangasluoma, Juha; Kirkby, Jasper; Kürten, Andreas; Kupc, Agnieszka; Lehtipalo, Katrianne; Nieminen, Tuomo; Riccobono, Francesco; Rondo, Linda; Schobesberger, Siegfried; Steiner, Gerhard; Tomé, António; Wimmer, Daniela; Baltensperger, Urs; Wagner, Paul E; Curtius, Joachim

    2016-01-01

    Binary nucleation of sulphuric acid-water particles is expected to be an important process in the free troposphere at low temperatures. SAWNUC (Sulphuric Acid Water Nucleation) is a model of binary nucleation that is based on laboratory measurements of the binding energies of sulphuric acid and water in charged and neutral clusters. Predictions of SAWNUC are compared for the first time comprehensively with experimental binary nucleation data from the CLOUD chamber at European Organization for Nuclear Research. The experimental measurements span a temperature range of 208–292 K, sulphuric acid concentrations from 1·106 to 1·109 cm−3, and distinguish between ion-induced and neutral nucleation. Good agreement, within a factor of 5, is found between the experimental and modeled formation rates for ion-induced nucleation at 278 K and below and for neutral nucleation at 208 and 223 K. Differences at warm temperatures are attributed to ammonia contamination which was indicated by the presence of ammonia-sulphu...

  8. Passivation of chalcopyrite during the leaching with sulphuric acid solution in presence of sodium nitrate

    Directory of Open Access Journals (Sweden)

    Sokić Miroslav D.

    2010-01-01

    Full Text Available In this work, the process of the chalcopyrite leaching in sulphuric acid solution was investigated. Sodium nitrate was used as oxidant in the leaching process. Chemical reactions of leaching and their thermodynamic possibilities are predicted based on the calculated Gibbs energies and analysis of E−pH diagrams. The negative values of the Gibbs energy show that all chemical reactions are thermodynamically feasible at atmospheric pressure and in a temperature range 25-90°C. At high electrode potential and low pH values, Cu2+, Fe2+ and Fe3+ ions exist in water solutions. The increase of temperature reduces the probability of Fe3+ ion existence in the system. The chalcopyrite concentrate, enriched in the “Rudnik” flotation plant, with 27.08% Cu, 25.12% Fe, 4.15% Zn and 2.28% Pb was used in the work. XRD and DTA analysis of the concentrate reveals that the sample contains mainly the chalcopyrite with small amount of sphalerite. For the description of the reaction of leaching process the leach residuals, obtained at different conditions, were chosen for XRD, TG/DTA and SEM/EDX analyses. The elemental sulphur and chalcopyrite phases identified in leach residuals confirm our prediction that the elemental sulphur is formed during the leaching process. Accordingly, elemental sulphur is the main product of the reaction, while a minor amount of sulphide sulphur is oxidized to sulphate during the leaching. The sulphur formed during the reaction was precipitated at the particle surfaces, and slowed down the leaching rate in the final stage of leaching process. In the initial stage, the reaction rate was controlled by the surface reaction. The mechanism, latter has been changed into a diffusion controlled one.

  9. 硫磺和硫酸供需预测及硫磺的用途——2000年国际硫磺和硫酸会议侧记(Ⅰ)%Forecast of sulphur and sulphuric acid supply and demand and application of sulphur-Sidelights on Sulphur 2000 International Conference(Ⅰ)

    Institute of Scientific and Technical Information of China (English)

    赵增泰

    2001-01-01

    The situation of world's sulphur and sulphuric acid industry are introduced with respects to the production and consumption of sulphur and sulphuric acid, potential resource of sulphur in Venezuelan, application of sulphuric acid in nickel and cobalt production by pressure leach and of sulphur fertilizers and sulphur-containing waste solid in agriculture, and sour gas injection.%介绍了世界硫磺和硫酸生产和消费,委内瑞拉的巨大硫磺潜在资源,加压法生产镍、钴的硫磺消费,硫肥和含硫废弃物的利用,酸性气体回注到地下等情况。

  10. KINETIC AND MECHANISTIC STUDY OF OXIDATION OF ATENOLOL BY CERIUM (IV IN SULPHURIC ACIDIC MEDIUM

    Directory of Open Access Journals (Sweden)

    Fadnis G Anand

    2012-03-01

    Full Text Available The kinetics of oxidation of antihypertensive drug, atenolol by cerium (IV in sulphuric acidic medium has been studied spectrophotometrically at 360 nm. The reaction between cerium (IV and atenolol in acidic medium has exhibited 2:1 stoichiometry. The order of the reaction with respect to atenolol has been found to be one. The observed pseudo first order rate constants kobs increased with sulphuric acid and hydrogen ion concentrations where as decreased bisulphate ion concentration indicating the formation bisulphato reactive species of cerium (IV in the present reaction. The thermodynamic parameters have been evaluated from the temperature variation kinetic data. A possible mechanism is proposed which has been validated by derived rate law. An attempt has been made to use rate data for kinetic estimation of atenolol.KEYWORDS:

  11. Heterogeneous freezing of single sulphuric acid solution droplets: laboratory experiments utilising an acoustic levitator

    Science.gov (United States)

    Ettner, M.; Mitra, S. K.; Borrmann, S.

    2004-03-01

    The heterogeneous freezing temperatures of single binary sulphuric acid solution droplets were measured in dependency of acid concentration down to temperatures as low as -70°C. In order to avoid influence of supporting substrates on the freezing characteristics, the droplets were suspended by means of an acoustic levitator. The droplets contained immersed particles of graphite, kaolin or montmorillonite in order to study the influence of the presence of such contamination on the freezing temperature. The radii of the suspended droplets spanned the range between 0,4 and 1,1 mm and the concentration of the sulphuric acid solution varied between 5 and 25 weight percent. The presence of the particles in the solution raises the freezing temperature with respect to homogeneous freezing of these solution droplets. The pure solution droplets can be supercooled up to 40° below the ice-acid solution thermodynamic equilibrium curve. Depending on the concentration of sulphuric acid and the nature of the impurity the polluted droplets froze between -11°C and -35°C. The experimental set-up, combining a deep freezer with a movable ultrasonic levitator and suitable optics, proved to be a useful approach for such investigations on individual droplets.

  12. Biogenic Sulphate, Sulphur Dioxide and Methanesulphonic Acid Ratios over the North Atlantic

    Science.gov (United States)

    Seguin, A.; Norman, A.; Wadleigh, M.; Siauw, A.; Eaton, S.

    2006-12-01

    Methanesulphonic acid (MSA) and sulphate are the end products of two different oxidation pathways of atmospheric dimethylsulphide (DMS). Sulphate aerosols can act as cloud condensation nuclei that affect incoming solar radiation and thus climate. The branching ratio cannot be measured using sulphate concentrations alone due to anthropogenic sulphate contributions. Stable isotope techniques, however, can be used to define continental and biogenic emissions, determine the origin of sulphate in aerosol samples and provide insight into DMS oxidation. Size segregated aerosol filters, sulphur dioxide and atmospheric DMS were collected during the summer 2003 Canadian Surface Ocean Lower Atmospheric Study (C-SOLAS) over the North Atlantic. Isotope values along with sulphate, MSA and cation concentrations were analysed. Non-sea salt (NSS) sulphate concentrations where as high as 11000 ng/m3. Biogenic sulphate concentrations ranged between 100 and 800 ng/m3 while biogenic sulphur dioxide concentrations ranged between 20 and 4000 ng/m3. Polluted air masses see an increase in biogenic sulphur dioxide indicating an influence of human activity on the oxidation pathways of DMS. MSA and biogenic sulphur dioxide concentrations are compared to the biogenic sulphate to explore the branching ratio.

  13. A classical reactive potential for molecular clusters of sulphuric acid and water

    CERN Document Server

    Stinson, Jake L; Ford, Ian J

    2016-01-01

    We present a two-state empirical valence bond (EVB) potential describing interactions between sulphuric acid and water molecules and designed to model proton transfer between them within a classical dynamical framework. The potential has been developed in order to study the properties of molecular clusters of these species, which are thought to be relevant to atmospheric aerosol nucleation. The particle swarm optimisation method has been used to fit the parameters of the EVB model to density functional theory (DFT) calculations. Features of the parametrised model and DFT data are compared and found to be in satisfactory agreement. In particular, it is found that a single sulphuric acid molecule will donate a proton when clustered with four water molecules at 300 K and that this threshold is temperature dependent.

  14. Solubility and reactivity of peroxyacetyl nitrate (PAN) in dilute aqueous salt solutions and in sulphuric acid

    Science.gov (United States)

    Frenzel, A.; Kutsuna, S.; Takeuchi, K.; Ibusuki, T.

    The loss rates of PAN in several dilute aqueous salt solutions (NaBr, Na 2SO 3, KI, NaNO 2, FeCl 3, and FeSO 4) and in sulphuric acid were measured at 279 K with a simple bubbler experiment. They are little different from that in pure water. For 5 M sulphuric acid hydrolysis and solubility were determined in the temperature range of 243-293 K. The hydrolysis rate kh=3.2×10 -4 s -1 at 293 K is close to that in water. The observed temperature dependence of the Henry's Law constant H=10- 6.6±0.6exp((4780±420)/T) M atm -1 leads to enthalpy and entropy of solvation Δ Hsolv=-39.7±3.5 kJ mol -1 and Δ Ssolv=-126±11 J mol -1 K -1, respectively.

  15. Removal Cu(II ions from water using sulphuric acid treated Lagenaria vulgaris Shell (Cucurbitaceae

    Directory of Open Access Journals (Sweden)

    Ljupković, R.B.

    2011-09-01

    Full Text Available Removal of Cu(II ions from water solutions by sulphuric acid treated Lagenaria vulgaris shell (ccLVB was studied. Batch experiments were done by shaking a fixed mass of biosorbent (1.0 g with 250 cm3 of 50.0 mg dm–3 Cu(II solutions, at pH ranged from 2 up to 6. Metal concentration in the filtrates as well as in the initial solution was determined by flame atomic absorption spectrometry. Results show that efficiency of Cu(II ions uptake by sulphuric acid treated Lagenaria vulgaris shell is significantly greater than raw Lagenaria vulgaris biosorbent. In addition, there is no significant effect of initial pH of solution on Cu(II ions uptake by ccLVB and obtained biosorbent can be applied in a wide range of pH.

  16. Role of sulphuric acid, ammonia and galactic cosmic rays in atmospheric aerosol nucleation

    CERN Document Server

    Kirkby, Jasper; Almeida, João; Dunne, Eimear; Duplissy, Jonathan; Ehrhart, Sebastian; Franchin, Alessandro; Gagné, Stéphanie; Ickes, Luisa; Kürten, Andreas; Kupc, Agnieszka; Metzger, Axel; Riccobono, Francesco; Rondo, Linda; Schobesberger, Siegfried; Tsagkogeorgas, Georgios; Wimmer, Daniela; Amorim, Antonio; Bianchi, Federico; Breitenlechner, Martin; David, André; Dommen, Josef; Downard, Andrew; Ehn, Mikael; Flagan, Richard C; Haider, Stefan; Hansel, Armin; Hauser, Daniel; Jud, Werner; Junninen, Heikki; Kreissl, Fabian; Kvashin, Alexander; Laaksonen, Ari; Lehtipalo, Katrianne; Lima, Jorge; Lovejoy, Edward R; Makhmutov, Vladimir; Mathot, Serge; Mikkilä, Jyri; Minginette, Pierre; Mogo, Sandra; Nieminen, Tuomo; Onnela, Antti; Pereira, Paulo; Petäjä, Tuukka; Schnitzhofer, Ralf; Seinfeld, John H; Sipilä, Mikko; Stozhkov, Yuri; Stratmann, Frank; Tomé, Antonio; Vanhanen, Joonas; Viisanen, Yrjo; Vrtala, Aron; Wagner, Paul E; Walther, Hansueli; Weingartner, Ernest; Wex, Heike; Winkler, Paul M; Carslaw, Kenneth S; Worsnop, Douglas R; Baltensperger, Urs; Kulmala, Markku

    2011-01-01

    Atmospheric aerosols exert an important influence on climate1 through their effects on stratiform cloud albedo and lifetime2 and the invigoration of convective storms3. Model calculations suggest that almost half of the global cloud condensation nuclei in the atmospheric boundary layer may originate from the nucleation of aerosols from trace condensable vapours4, although the sensitivity of the number of cloud condensation nuclei to changes of nucleation rate may be small5, 6. Despite extensive research, fundamental questions remain about the nucleation rate of sulphuric acid particles and the mechanisms responsible, including the roles of galactic cosmic rays and other chemical species such as ammonia7. Here we present the first results from the CLOUD experiment at CERN. We find that atmospherically relevant ammonia mixing ratios of 100 parts per trillion by volume, or less, increase the nucleation rate of sulphuric acid particles more than 100–1,000-fold. Time-resolved molecular measurements reveal that n...

  17. Surface modification of mineral dust particles by sulphuric acid processing: implications for CCN and IN abilities

    OpenAIRE

    P. Reitz; C. Spindler; T. F. Mentel; Poulain, L.; H. Wex; K. Mildenberger; D. Niedermeier; Hartmann, S.; T. Clauss; F. Stratmann; R. C. Sullivan; Demott, P. J.; Petters, M. D.; Sierau, B.; Schneider, J.

    2011-01-01

    The ability of coated mineral dust particles to act as cloud condensation nuclei (CCN) and ice nuclei (IN) was investigated at LACIS (Leipzig Aerosol Cloud Interaction Simulator) during the FROST1- and FROST2-campaigns (Freezing of dust). Sulphuric acid was condensed on the particles which afterwards were optionally humidified, treated with ammonia vapour and/or heat. By means of aerosol mass spectrometry we found evidence that processi...

  18. Surface modification of mineral dust particles by sulphuric acid processing: implications for ice nucleation abilities

    OpenAIRE

    P. Reitz; C. Spindler; T. F. Mentel; Poulain, L.; H. Wex; K. Mildenberger; D. Niedermeier; Hartmann, S.; T. Clauss; F. Stratmann; R. C. Sullivan; Demott, P. J.; Petters, M. D.; Sierau, B.; Schneider, J.

    2011-01-01

    The ability of coated mineral dust particles to act as ice nuclei (IN) was investigated at LACIS (Leipzig Aerosol Cloud Interaction Simulator) during the FROST1- and FROST2-campaigns (Freezing of dust). Sulphuric acid was condensed on the particles which afterwards were optionally humidified, treated with ammonia vapour and/or heat. By means of aerosol mass spectrometry we found evidence that processing of mineral dust particles with su...

  19. Hydrometallurgical process for zinc recovery from electric arc furnace dust (EAFD): part I: Characterization and leaching by diluted sulphuric acid.

    Science.gov (United States)

    Oustadakis, P; Tsakiridis, P E; Katsiapi, A; Agatzini-Leonardou, S

    2010-07-15

    The present paper is the first of a series of two articles dealing with the development of an integrated process for the recovery of zinc from electric arc furnace dust (EAFD), a hazardous industrial waste generated in the collection of particulate material during steelmaking process via electric arc furnace. Part I presents the EAFD characterization and its leaching process by diluted sulphuric acid, whereas Part II deals with the purification of the leach liquor and the recovery of zinc by solvent extraction/electrowinning. The characterization of the examined electric arc furnace dust was carried out by using granulometry analysis, chemical analysis, X-ray diffraction (XRD), thermogravimetric/differential thermal analysis (TG/DTA) and scanning electron microscopy (SEM). The leaching process was based on the Zn extraction with diluted sulphuric acid from EAFD under atmospheric conditions and without using any preliminary treatment. Statistical design and analysis of experiments were used, in order to determine the main effects and interactions of the leaching process factors, which were: acid normality, temperature and solid to liquid ratio. The zinc recovery efficiency on the basis of EAFD weight reached 80%. X-ray diffraction and scanning electron microscopy were used for the characterization of the leached residues.

  20. The charging of neutral dimethylamine and dimethylamine-sulphuric acid clusters using protonated acetone

    Directory of Open Access Journals (Sweden)

    K. Ruusuvuori

    2014-11-01

    Full Text Available Sulphuric acid is generally considered one of the most important substances taking part in atmospheric particle formation. However, in typical atmospheric conditions in the lower troposphere sulphuric acid and water alone are unable to form particles. It has been suggested that strong bases may stabilize sulphuric acid clusters so that particle formation may occur. More to the point, amines – strong organic bases – have become the subject of interest as possible cause for such stabilisation. To probe whether amines play a role in atmospheric nucleation, we need to be able to measure accurately the gas-phase amine vapour concentration. Such measurements often include charging the neutral molecules and molecular clusters in the sample. Since amines are bases, the charging process should introduce a positive charge. This can be achieved for example using a positively charged reagent with a suitable proton affinity. In our study, we have used quantum chemical methods combined with a cluster dynamics code to study the use of acetone as a reagent in chemical ionization and compared the results with measurements performed with a chemical ionization atmospheric pressure interface time-of-flight mass spectrometer (CI-APi-TOF. The computational results indicate that protonated acetone is an effective reagent in chemical ionization. However, in the experiments the charger ions were not depleted at the predicted dimethylamine concentrations, indicating that either the modelling scheme or the experimental results – or both – contain unidentified sources of error.

  1. The charging of neutral dimethylamine and dimethylamine-sulphuric acid clusters using protonated acetone

    Science.gov (United States)

    Ruusuvuori, K.; Hietala, P.; Kupiainen-Määttä, O.; Jokinen, T.; Junninen, H.; Sipilä, M.; Kurtén, T.; Vehkamäki, H.

    2014-11-01

    Sulphuric acid is generally considered one of the most important substances taking part in atmospheric particle formation. However, in typical atmospheric conditions in the lower troposphere sulphuric acid and water alone are unable to form particles. It has been suggested that strong bases may stabilize sulphuric acid clusters so that particle formation may occur. More to the point, amines - strong organic bases - have become the subject of interest as possible cause for such stabilisation. To probe whether amines play a role in atmospheric nucleation, we need to be able to measure accurately the gas-phase amine vapour concentration. Such measurements often include charging the neutral molecules and molecular clusters in the sample. Since amines are bases, the charging process should introduce a positive charge. This can be achieved for example using a positively charged reagent with a suitable proton affinity. In our study, we have used quantum chemical methods combined with a cluster dynamics code to study the use of acetone as a reagent in chemical ionization and compared the results with measurements performed with a chemical ionization atmospheric pressure interface time-of-flight mass spectrometer (CI-APi-TOF). The computational results indicate that protonated acetone is an effective reagent in chemical ionization. However, in the experiments the charger ions were not depleted at the predicted dimethylamine concentrations, indicating that either the modelling scheme or the experimental results - or both - contain unidentified sources of error.

  2. An isotopic analysis of ionising radiation as a source of sulphuric acid

    DEFF Research Database (Denmark)

    Enghoff, Martin Andreas Bødker; Bork, Nicolai Christian; Hattori, S.

    2012-01-01

    a missing source. In this study the production of sulphuric acid from SO2 through a number of different pathways is investigated. The production methods are standard gas phase oxidation by OH radicals produced by ozone photolysis with UV light, liquid phase oxidation by ozone, and gas phase oxidation...... initiated by gamma rays. The distributions of stable sulphur isotopes in the products and substrate were measured using isotope ratio mass spectrometry. All methods produced sulphate enriched in S-34 and we find an enrichment factor (delta S-34) of 8.7 +/- 0.4 parts per thousand (1 standard deviation......) for the UV-initiated OH reaction. Only UV light (Hg emission at 253.65 nm) produced a clear non-mass-dependent excess of S-33. The pattern of isotopic enrichment produced by gamma rays is similar, but not equal, to that produced by aqueous oxidation of SO2 by ozone. This, combined with the relative yields...

  3. An isotope view on ionising radiation as a source of sulphuric acid

    DEFF Research Database (Denmark)

    Enghoff, Martin Andreas Bødker; Bork, Nicolai Christian; Hattori, S.

    2012-01-01

    oxidation initiated by gamma rays. The distributions of stable sulphur isotopes in the products and substrate were measured using isotope ratio mass spectrometry. All methods produced sulphate enriched in 34S and we find a δ34S value of 8.7 ± 0.4‰ (1 standard deviation) for the UV...... a missing source. In this study the production of sulphuric acid from SO2 through a number of different pathways is investigated. The production methods are standard gas phase oxidation by OH radicals produced by ozone photolysis with UV light, liquid phase oxidation by ozone, and gas phase......-initiated OH reaction. Only UV light (Hg emission at 253.65 nm) produced a clear non-mass-dependent excess of 33S. The pattern of isotopic enrichment produced by gamma rays is similar, but not equal, to that produced by aqueous oxidation of SO2 by ozone. This, combined with the relative...

  4. Stratigraphic and geophysical integrated methodologies for the interpretation of sulphur water formational environment in Salento (Italy)

    Energy Technology Data Exchange (ETDEWEB)

    Margiotta, S.; Negri, S. [Dipartimento di Scienze dei Materiali-Osservatorio di Fisica, Chimica, Geologia Ambientali-Universita del Salento (Italy)

    2008-06-13

    The Salento coal deposits (south-eastern Italy) are unutilized because these deposits are thin and nearly uneconomic but they have a high scientific and economic value due to their high organic sulphur content. The studied area is located in the western Salento peninsula where wells used by a fish-farm (''Ittica Ugento'') have shown high concentrations of hydrogen sulphide. Data from surface and boreholes stratigraphic surveys integrated with electrical resistivity tomography (ERT) allow us to define the structure, depths and geometry of the aquifer and its relationship with saltwater intrusion. Induced polarization (IP) with pole-dipole array survey has been carried out near the coastline. The value measured was over 50 msec. A direct relationship is shown to exist between IP values and the aquifer containing sulphur water. The high resolution of the data obtained with the applied methods not only shows the validity of the methodology but is the key to evaluating the groundwater resources of the area. The proposed mechanism is that of entrapment of sulphur water in a graben structure: when sulphate-enriched waters of marine origin come into contact with organic substances and lignite deposits (Galatone Formation, Oligocene), they are deprived not only of free oxygen, but also generate hydrogen sulphide as a result of the reduction of sulphates. (author)

  5. Integration of advanced oxidation processes at mild conditions in wet scrubbers for odourous sulphur compounds treatment.

    Science.gov (United States)

    Vega, Esther; Martin, Maria J; Gonzalez-Olmos, Rafael

    2014-08-01

    The effectiveness of different advanced oxidation processes on the treatment of a multicomponent aqueous solution containing ethyl mercaptan, dimethyl sulphide and dimethyl disulphide (0.5 mg L(-1) of each sulphur compound) was investigated with the objective to assess which one is the most suitable treatment to be coupled in wet scrubbers used in odour treatment facilities. UV/H2O2, Fenton, photo-Fenton and ozone treatments were tested at mild conditions and the oxidation efficiency obtained was compared. The oxidation tests were carried out in magnetically stirred cylindrical quartz reactors using the same molar concentration of oxidants (hydrogen peroxide or ozone). The results show that ozone and photo-Fenton are the most efficient treatments, achieving up to 95% of sulphur compounds oxidation and a mineralisation degree around 70% in 10 min. Furthermore, the total costs of the treatments taking into account the capital and operational costs were also estimated for a comparative purpose. The economic analysis revealed that the Fenton treatment is the most economical option to be integrated in a wet scrubber to remove volatile organic sulphur compounds, as long as there are no space constraints to install the required reactor volume. In the case of reactor volume limitation or retrofitting complexities, the ozone and photo-Fenton treatments should be considered as viable alternatives.

  6. Sensorially important aldehyde production from amino acids in model wine systems: impact of ascorbic acid, erythorbic acid, glutathione and sulphur dioxide.

    Science.gov (United States)

    Grant-Preece, Paris; Fang, Hongjuan; Schmidtke, Leigh M; Clark, Andrew C

    2013-11-01

    The efficiency of different white wine antioxidant systems in preventing aldehyde production from amino acids by oxidative processes is not well understood. The aim of this study was to assess the efficiency of sulphur dioxide alone and in combination with either glutathione, ascorbic acid or its stereoisomer erythorbic acid, in preventing formation of the sensorially important compounds methional and phenylacetaldehyde from methionine and phenylalanine in model white wine. UHPLC, GC-MS/MS, LC-MS/MS, flow injection analysis and luminescence sensors determined both compositional changes during storage, and sulphur dioxide-aldehyde apparent equilibrium constants. Depending on temperature (25 or 45°C) or extent of oxygen supply, sulphur dioxide was equally or more efficient in impeding the production of methional compared to the other antioxidant systems. For phenylacetaldehyde, erythorbic acid or glutathione with sulphur dioxide provided improved inhibition compared to sulphur dioxide alone, in conditions of limited oxygen consumption. The results also demonstrate the extent to which sulphur dioxide addition can lower the free aldehyde concentrations to below their aroma thresholds.

  7. Extraction of As (V from sulphuric acid solutions by Cyanex 925

    Directory of Open Access Journals (Sweden)

    Alguacil, F. J.

    1998-05-01

    Full Text Available The extraction of As (V from sulphuric acid solutions using the phosphine oxide Cyanex 925 dissolved in various diluents was studied. Arsenic extraction depends strongly of temperature, decreasing with the increase of this variable, and to a lesser extent on the sulphuric acid concentration, approximately up to 300 g/L H2SO4. To increase the degree of arsenic extraction it needs to operate with Cyanex 925 concentrations of at least 50 % v/v, although this also promotes the coextraction of the acid. Stripping of the loaded arsenic and sulphuric acid can be carried out using water, better As-H2SO4 separations can be obtained at lower temperatures or operating using high O/A ratios for acid stripping and lower O/A ratios for arsenic stripping.

    Se estudia la extracción de As (V de disoluciones sulfúricas mediante Cyanex 925 disuelto en varios diluyentes. La extracción de arsénico depende de la temperatura y disminuye al aumentar esta variable, y también la concentración de ácido sulfúrico, hasta 300 g/L del ácido. Para aumentar la extracción del metal es necesario trabajar con concentraciones de Cyanex 925 superiores a 50 % v/v, aunque a la vez aumenta la coextracción del ácido. La reextracción se puede llevar a cabo con agua, obteniéndose mejores separaciones As-H2SO4 trabajando con temperaturas bajas o con altas relaciones O/A, para reextraer el ácido, y bajas relaciones para el arsénico.

  8. Enhanced high temperature thermoelectric response of sulphuric acid treated conducting polymer thin films

    KAUST Repository

    Sarath Kumar, S. R.

    2015-11-24

    We report the high temperature thermoelectric properties of solution processed pristine and sulphuric acid treated poly(3, 4-ethylenedioxythiophene):poly(4-styrenesulfonate) (or PEDOT:PSS) films. The acid treatment is shown to simultaneously enhance the electrical conductivity and Seebeck coefficient of the metal-like films, resulting in a five-fold increase in thermoelectric power factor (0.052 W/m. K ) at 460 K, compared to the pristine film. By using atomic force micrographs, Raman and impedance spectra and using a series heterogeneous model for electrical conductivity, we demonstrate that acid treatment results in the removal of PSS from the films, leading to the quenching of accumulated charge-induced energy barriers that prevent hopping conduction. The continuous removal of PSS with duration of acid treatment also alters the local band structure of PEDOT:PSS, resulting in simultaneous enhancement in Seebeck coefficient.

  9. Investigating the significance of zero-point motion in small molecular clusters of sulphuric acid and water

    CERN Document Server

    Stinson, Jake; Ford, Ian

    2014-01-01

    The nucleation of particles from trace gases in the atmosphere is an important source of cloud condensation nuclei (CCN), and these are vital for the formation of clouds in view of the high supersaturations required for homogeneous water droplet nucleation. The methods of quantum chemistry have increasingly been employed to model nucleation due to their high accuracy and efficiency in calculating configurational energies; and nucleation rates can be obtained from the associated free energies of particle formation. However, even in such advanced approaches, it is typically assumed that the nuclei have a classical nature, which is questionable for some systems. The importance of zero-point motion (also known as quantum nuclear dynamics) in modelling small clusters of sulphuric acid and water is tested here using the path integral molecular dynamics (PIMD) method at the density functional theory (DFT) level of theory. The general effect of zero-point motion is to distort the mean structure slightly, and to promo...

  10. A classical reactive potential for molecular clusters of sulphuric acid and water

    Energy Technology Data Exchange (ETDEWEB)

    Stinson, Jake L.; Kathmann, Shawn M.; Ford, Ian J.

    2015-10-12

    We present a two state empirical valence bond (EVB) potential describing interactions between sulphuric acid and water molecules and designed to model proton transfer between them within a classical dynamical framework. The potential has been developed in order to study the properties of molecular clusters of these species, which are thought to be relevant to atmospheric aerosol nucleation. The particle swarm optimisation method has been used to fit the parameters of the EVB model to density functional theory (DFT) calculations. Features of the parametrised model and DFT data are compared and found to be in satisfactory agreement. In particular, it is found that a single sulphuric acid molecule will donate a proton when clustered with four water molecules at 300 K and that this threshold is temperature dependent. SMK was supported in part by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences, and Biosciences; JLS and IJF were supported by the IMPACT scheme at University College London (UCL). We acknowledge the UCL Legion High Performance Computing Facility, and associated support services together with the resources of the National Energy Research Scientific Computing Center (NERSC), which is supported by the U.S. Department of Energy under Contract No. DE-AC02- 05CH11231. JLS thanks Dr. Gregory Schenter, Dr. Theo Kurtén and Prof. Hanna Vehkamäki for important guidance and discussions.

  11. Production of activated carbon from a new precursor molasses by activation with sulphuric acid.

    Science.gov (United States)

    Legrouri, K; Khouya, E; Ezzine, M; Hannache, H; Denoyel, R; Pallier, R; Naslain, R

    2005-02-14

    Activated carbon has been prepared from molasses, a natural precursor of vegetable origin resulting from the sugar industry in Morocco. The preparation of the activated carbon from the molasses has been carried out by impregnation of the precursor with sulphuric acid, followed by carbonisation at varying conditions (temperature and gas coverage) in order to optimize preparation parameters. The influence of activation conditions was investigated by determination of adsorption capacity of methylene blue and iodine, the BET surface area, and the pore volume of the activated carbon were determined while the micropore volume was determined by the Dubinin-Radushkevich (DR) equation. The activated materials are mainly microporous and reveal the type I isotherm of the Brunauer classification for nitrogen adsorption. The activated carbons properties in this study were found for activation of the mixture (molasses/sulphuric acid) in steam at 750 degrees C. The samples obtained in this condition were highly microporous, with high surface area (> or =1200 m2/g) and the maximum adsorption capacity of methylene blue and iodine were 435 and 1430 mg/g, respectively.

  12. Effect of ions on the measurement of sulphuric acid in the CLOUD experiment at CERN

    CERN Document Server

    Rondo, L; Ehrhart, S; Schobesberger, S; Franchin, A; Junninen, H; Petäjä, T; Sipilä, M; Worsnop, D R; Curtius, J

    2014-01-01

    Ternary aerosol nucleation experiments were conducted in the CLOUD chamber at CERN in order to investigate the influence of ions on new particle formation. Neutral and ion-induced nucleation experiments, i.e., with and without the presence of ions, were carried out under precisely controlled conditions. The sulphuric acid concentration was measured with a Chemical Ionization Mass Spectrometer (CIMS) during the new particle formation experiments. The added ternary trace gases were ammonia (NH3), dimethylamine (DMA, C2H7N) or oxidised products of pinanediol (PD, C10H18O2). When pinanediol was introduced into the chamber, an increase in the mass spectrometric signal used to determine the sulphuric acid concentration (m/z 97, i.e., HSO4−) was observed due to ions from the CLOUD chamber. The enhancement was only observed during ion-induced nucleation measurements by using either galactic cosmic rays (GCR) or the proton synchrotron (PS) pion beam for the ion generation, respectively. The ion effect typically invo...

  13. Extraction of Zinc and Manganese from Alkaline and Zinc-Carbon Spent Batteries by Citric-Sulphuric Acid Solution

    Directory of Open Access Journals (Sweden)

    Francesco Ferella

    2010-01-01

    Full Text Available The paper is focused on the recovery of zinc and manganese from alkaline and zinc-carbon spent batteries. Metals are extracted by sulphuric acid leaching in the presence of citric acid as reducing agent. Leaching tests are carried out according to a 24 full factorial design, and empirical equations for Mn and Zn extraction yields are determined from experimental data as a function of pulp density, sulphuric acid concentration, temperature, and citric acid concentration. The highest values experimentally observed for extraction yields were 97% of manganese and 100% of zinc, under the following operating conditions: temperature 40∘C, pulp density 20%, sulphuric acid concentration 1.8 M, and citric acid 40 g L-1. A second series of leaching tests is also performed to derive other empirical models to predict zinc and manganese extraction. Precipitation tests, aimed both at investigating precipitation of zinc during leaching and at evaluating recovery options of zinc and manganese, show that a quantitative precipitation of zinc can be reached but a coprecipitation of nearly 30% of manganese also takes place. The achieved results allow to propose a battery recycling process based on a countercurrent reducing leaching by citric acid in sulphuric solution.

  14. Corrosion behaviour and structure of the surface layer formed on austempered ductile iron in concentrated sulphuric acid

    Energy Technology Data Exchange (ETDEWEB)

    Krawiec, H. [AGH University of Science and Technology, Department of Foundry Engineering, ul. Reymonta 23, 30-059 Cracow (Poland)]. E-mail: krawiec@uci.agh.edu.pl; Stypula, B. [AGH University of Science and Technology, Department of Foundry Engineering, ul. Reymonta 23, 30-059 Cracow (Poland); Stoch, J. [Institute of Catalysis and Surface Chemistry, Polish Academy of Sciences (PAS), ul. Niezapominajek 8, 30-239 Cracow (Poland); Mikolajczyk, M. [Institute of Catalysis and Surface Chemistry, Polish Academy of Sciences (PAS), ul. Niezapominajek 8, 30-239 Cracow (Poland)

    2006-03-15

    The aim of this paper is to investigate the structure of the surface layer formed on austempered ductile iron (ADI) after exposure to hot concentrated sulphuric acid at the open circuit potential value (OCP). The results derived from polarization measurements carried out in sulphuric acid at a temperature of 90 deg. C show that anodic dissolution of ADI is divided into three stages (corresponding to three anodic dissolution peaks). The structure of the layer formed on alloys at 90 deg. C at OCP was investigated using X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). SEM analysis shows that the main elements of the surface layer are iron, silicon, oxygen, sulphur, and carbon. The binding energy recorded in individual bands indicates that the surface layer includes mainly SiO{sub 2} and FeOOH. The presence of sulphur at the lower oxidation state (S{sup 2-}) indicates that sulphuric acid undergoes reduction during this process. The corrosion resistance of these alloys is connected with the presence of SiO{sub 2} in the surface layer.

  15. Electrodeposition of nickel powder from nickel sulphate solution in presence of glycerol and sulphuric acid

    Directory of Open Access Journals (Sweden)

    S.G. Viswanath

    2013-09-01

    Full Text Available Nickel powder was obtained by electrodeposition of nickel from boric acid, glycerol and sulphuric acid. The morphology and particle size of these powders were studied. Spongy, irregular, flaky, fibrous and aggregate particles were obtained. Size of more than 85% particles was smaller than 384µm. From XRD graphs, it was found that the smaller particles are in the range of 106 and 373 nm. The apparent density of nickel powder decreased with increase in concentration of glycerol. The stability of the powder and current efficiency were also studied. In absence of nickel sulphate there was some nickel deposition on the cathode. The effect was discussed in present work. New definition for electrodeposition was suggested.

  16. The study on the methods of testing the sulphuric acid and the phosphoric acid in the air in workshops at the same time by chromatography of ions

    Institute of Scientific and Technical Information of China (English)

    Deng-Yan Long; Yan-Ling Huang; Ying-Ying Zhao

    2015-01-01

    Objective:To discuss the method and result of testing the sulphuric acid and the phosphoric acid in the air in workshops at the same time by chromatography of ions.Method:to measure the sulphuric acid and the phosphoric acid in the air in workshops by adopting chromatography of ions. During the experiment, collect the sulphuric acid and the phosphoric acid in the air by using porous glass plates and put them into ultrapure water, or by using microporous filtering film, adopting ultrasonic elution with ultrapure water, testing them with ion chromatograph after filtering through a 0.2 μm microporous filtering film. The operating conditions of chromatography of ions includes Type Ionpac AS19 separator column (4×250 mm), ASRS300 (4 mm) anion suppressor, Type Ionpac AG19 guard column, KOH eluent and conductivity detector.Result: The testing the sulphuric acid and the phosphoric acid at the same time through chromatography of ions turns out high resolution, good linearity with the correlation over 0.999. The accuracy can be controlled between 1.6%-5.5% under the testing; the percentage of accuracy can be guaranteed between 92%-107% with high sampling and analysis efficiency.Conclusion: The method can turn out ideal results by testing the sulphuric acid and the phosphoric acid at the same time. It is simple operations, Sensitive and accurate. It is worth being used widely.

  17. Volatile sulphur compounds-forming abilities of lactic acid bacteria: C-S lyase activities.

    Science.gov (United States)

    Bustos, Irene; Martínez-Bartolomé, Miguel A; Achemchem, Fouad; Peláez, Carmen; Requena, Teresa; Martínez-Cuesta, M Carmen

    2011-08-01

    Volatile sulphur compounds (VSCs) are of prime importance in the overall aroma of cheese and make a significant contribution to their typical flavours. Thus, the control of VSCs formation offers considerable potential for industrial applications. Here, lactic acid bacteria (LAB) from different ecological origins were screened for their abilities to produce VSCs from L-methionine. From the data presented, VSC-forming abilities were shown to be strain-specific and were correlated with the C-S lyase enzymatic activities determined using different approaches. High VSCs formation were detected for those strains that were also shown to possess high thiol-producing abilities (determined either by agar plate or spectrophotometry assays). Moreover, differences in C-S lyase activities were shown to correspond with the enzymatic potential of the strains as determined by in situ gel visualization. Therefore, the assessment of the C-S lyase enzymatic potential, by means of either of these techniques, could be used as a valuable approach for the selection of LAB strains with high VSC-producing abilities thus, representing an effective way to enhance cheese sulphur aroma compounds synthesis. In this regard, this study highlights the flavour forming potential of the Streptococcus thermophilus STY-31, that therefore could be used as a starter culture in cheese manufacture. Furthermore, although C-S lyases are involved in both biosynthetic and catabolic pathways, an association between methionine and cysteine auxotrophy of the selected strains and their VSCs-producing abilities could not be found.

  18. Kinetics and mechanism of sphalerite leaching by sodium nitrate in sulphuric acid solution

    Directory of Open Access Journals (Sweden)

    Sokić M.

    2012-01-01

    Full Text Available Interest for application of hydrometallurgical processes in a processing of complex sulphide ores and concentrates has increased in recent years. Their application provides better metal recoveries and reduced emission of gaseous and toxic ageneses in the environment. The kinetics and mechanism of sphalerite leaching from complex sulphide concentrate with sulphuric acid and sodium nitrate solution at standard conditions was presented in this paper. The influences of temperature and time on the leaching degree of zinc were investigated and kinetic analysis of the process was accomplished. With temperature increasing from 60 to 90°C, the zinc leaching increased from 25.23% to 71.66% after 2 hours, i.e. from 59.40% to 99.83% after 4 hours. The selected kinetic model indicated that the diffusion through the product layer was the rate-controlling step during the sphalerite leaching. The activation energy was determined to be 55 kJ/mol in the temperature range 60-90°C. XRD, light microscopy and SEM/EDX analyses of the complex concentrate and leach residue confirmed formation of elemental sulphur and diffusion-controlled leaching mechanism.

  19. Molecular understanding of sulphuric acid-amine particle nucleation in the atmosphere

    CERN Document Server

    Almeida, João; Kürten, Andreas; Ortega, Ismael K; Kupiainen-Määttä, Oona; Praplan, Arnaud P; Adamov, Alexey; Amorim, Antonio; Bianchi, Federico; Breitenlechner, Martin; David, André; Dommen, Josef; Donahue, Neil M; Downard, Andrew; Dunne, Eimear; Duplissy, Jonathan; Ehrhart, Sebastian; Flagan, Richard C; Franchin, Alessandro; Guida, Roberto; Hakala, Jani; Hansel, Armin; Heinritzi, Martin; Henschel, Henning; Jokinen, Tuija; Junninen, Heikki; Kajos, Maija; Kangasluoma, Juha; Keskinen, Helmi; Kupc, Agnieszka; Kurtén, Theo; Kvashin, Alexander N; Laaksonen, Ari; Lehtipalo, Katrianne; Leiminger, Markus; Leppä, Johannes; Loukonen, Ville; Makhmutov, Vladimir; Mathot, Serge; McGrath, Matthew J; Nieminen, Tuomo; Olenius, Tinja; Onnela, Antti; Petäjä, Tuukka; Riccobono, Francesco; Riipinen, Ilona; Rissanen, Matti; Rondo, Linda; Ruuskanen, Taina; Santos, Filipe D; Sarnela, Nina; Schallhart, Simon; Schnitzhofer, Ralf; Seinfeld, John H; Simon, Mario; Sipilä, Mikko; Stozhkov, Yuri; Stratmann, Frank; Tomé, Antonio; Tröstl, Jasmin; Tsagkogeorgas, Georgios; Vaattovaara, Petri; Viisanen, Yrjo; Virtanen, Annele; Vrtala, Aron; Wagner, Paul E; Weingartner, Ernest; Wex, Heike; Williamson, Christina; Wimmer, Daniela; Ye, Penglin; Yli-Juuti, Taina; Carslaw, Kenneth S; Kulmala, Markku; Curtius, Joachim; Baltensperger, Urs; Vehkamaki, Hanna; Kirkby, Jasper

    2013-01-01

    Nucleation of aerosol particles from trace atmospheric vapours is thought to provide up to half of global cloud condensation nuclei. Aerosols can cause a net cooling of climate by scattering sunlight and by leading to smaller but more numerous cloud droplets, which makes clouds brighter and extends their lifetimes. Atmospheric aerosols derived from human activities are thought to have compensated for a large fraction of the warming caused by greenhouse gases. However, despite its importance for climate, atmospheric nucleation is poorly understood. Recently, it has been shown that sulphuric acid and ammonia cannot explain particle formation rates observed in the lower atmosphere. It is thought that amines may enhance nucleation, but until now there has been no direct evidence for amine ternary nucleation under atmospheric conditions. Here we use the CLOUD (Cosmics Leaving OUtdoor Droplets) chamber at CERN and find that dimethylamine above three parts per trillion by volume can enhance particle formation rates ...

  20. Ethanol and biogas production after steam pretreatment of corn stover with or without the addition of sulphuric acid

    Science.gov (United States)

    2013-01-01

    Background Lignocellulosic biomass, such as corn stover, is a potential raw material for ethanol production. One step in the process of producing ethanol from lignocellulose is enzymatic hydrolysis, which produces fermentable sugars from carbohydrates present in the corn stover in the form of cellulose and hemicellulose. A pretreatment step is crucial to achieve efficient conversion of lignocellulosic biomass to soluble sugars, and later ethanol. This study has investigated steam pretreatment of corn stover, with and without sulphuric acid as catalyst, and examined the effect of residence time (5–10 min) and temperature (190–210°C) on glucose and xylose recovery. The pretreatment conditions with and without dilute acid that gave the highest glucose yield were then used in subsequent experiments. Materials pretreated at the optimal conditions were subjected to simultaneous saccharification and fermentation (SSF) to produce ethanol, and remaining organic compounds were used to produce biogas by anaerobic digestion (AD). Results The highest glucose yield achieved was 86%, obtained after pretreatment at 210°C for 10 minutes in the absence of catalyst, followed by enzymatic hydrolysis. The highest yield using sulphuric acid, 78%, was achieved using pretreatment at 200°C for 10 minutes. These two pretreatment conditions were investigated using two different process configurations. The highest ethanol and methane yields were obtained from the material pretreated in the presence of sulphuric acid. The slurry in this case was split into a solid fraction and a liquid fraction, where the solid fraction was used to produce ethanol and the liquid fraction to produce biogas. The total energy recovery in this case was 86% of the enthalpy of combustion energy in corn stover. Conclusions The highest yield, comprising ethanol, methane and solids, was achieved using pretreatment in the presence of sulphuric acid followed by a process configuration in which the slurry from the

  1. Ethanol and biogas production after steam pretreatment of corn stover with or without the addition of sulphuric acid

    Directory of Open Access Journals (Sweden)

    Bondesson Pia-Maria

    2013-01-01

    Full Text Available Abstract Background Lignocellulosic biomass, such as corn stover, is a potential raw material for ethanol production. One step in the process of producing ethanol from lignocellulose is enzymatic hydrolysis, which produces fermentable sugars from carbohydrates present in the corn stover in the form of cellulose and hemicellulose. A pretreatment step is crucial to achieve efficient conversion of lignocellulosic biomass to soluble sugars, and later ethanol. This study has investigated steam pretreatment of corn stover, with and without sulphuric acid as catalyst, and examined the effect of residence time (5–10 min and temperature (190–210°C on glucose and xylose recovery. The pretreatment conditions with and without dilute acid that gave the highest glucose yield were then used in subsequent experiments. Materials pretreated at the optimal conditions were subjected to simultaneous saccharification and fermentation (SSF to produce ethanol, and remaining organic compounds were used to produce biogas by anaerobic digestion (AD. Results The highest glucose yield achieved was 86%, obtained after pretreatment at 210°C for 10 minutes in the absence of catalyst, followed by enzymatic hydrolysis. The highest yield using sulphuric acid, 78%, was achieved using pretreatment at 200°C for 10 minutes. These two pretreatment conditions were investigated using two different process configurations. The highest ethanol and methane yields were obtained from the material pretreated in the presence of sulphuric acid. The slurry in this case was split into a solid fraction and a liquid fraction, where the solid fraction was used to produce ethanol and the liquid fraction to produce biogas. The total energy recovery in this case was 86% of the enthalpy of combustion energy in corn stover. Conclusions The highest yield, comprising ethanol, methane and solids, was achieved using pretreatment in the presence of sulphuric acid followed by a process configuration in

  2. Interactions of meteoric smoke particles with sulphuric acid in the Earth's stratosphere

    Science.gov (United States)

    Saunders, R. W.; Dhomse, S.; Tian, W. S.; Chipperfield, M. P.; Plane, J. M. C.

    2012-05-01

    Nano-sized meteoric smoke particles (MSPs) with iron-magnesium silicate compositions, formed in the upper mesosphere as a result of meteoric ablation, may remove sulphuric acid from the gas-phase above 40 km and may also affect the composition and behaviour of supercooled H2SO4-H2O droplets in the global stratospheric aerosol (Junge) layer. This study describes a time-resolved spectroscopic analysis of the evolution of the ferric (Fe3+) ion originating from amorphous ferrous (Fe2+)-based silicate powders dissolved in varying Wt % sulphuric acid (30-75 %) solutions over a temperature range of 223-295 K. Complete dissolution of the particles was observed under all conditions. The first-order rate coefficient for dissolution decreases at higher Wt % and lower temperature, which is consistent with the increased solution viscosity limiting diffusion of H2SO4 to the particle surfaces. Dissolution under stratospheric conditions should take less than a week, and is much faster than the dissolution of crystalline Fe2+ compounds. The chemistry climate model UMSLIMCAT (based on the UKMO Unified Model) was then used to study the transport of MSPs through the middle atmosphere. A series of model experiments were performed with different uptake coefficients. Setting the concentration of 1.5 nm radius MSPs at 80 km to 3000 cm-3 (based on rocket-borne charged particle measurements), the model matches the reported Wt % Fe values of 0.5-1.0 in Junge layer sulphate particles, and the MSP optical extinction between 40 and 75 km measured by a satellite-borne spectrometer, if the global meteoric input rate is about 20 tonnes per day. The model indicates that an uptake coefficient ≥0.01 is required to account for the observed two orders of magnitude depletion of H2SO4 vapour above 40 km.

  3. Microwave promoted rapid dehydration of aldoximes to nitrites using melamine-formaldehyde resin supported sulphuric acid in dry media

    Institute of Scientific and Technical Information of China (English)

    Ramin Rezaei; Marzeih Karami

    2011-01-01

    A simple and convenient procedure for the synthesis of nitriles by dehydration of aldoxime using supported sulphuric acid on melamine-formaldehyde resin (MFR) under solvent-free condition has been developed. A variety of aromatic and aliphatic aldoximes were converted to the corresponding nitriles. The resin was recovered and reused for subsequent reactions.

  4. Increase of sulphur-containing amino acids in transgenic potato with 10 ku zein gene from maize

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The 10 k zein gene of maize was under control of patatin class ⅠPromoter of potato and transferred into potato genome by the leaf-disc method.The expression of 10 ku zein was determined in the tuber of transgenic plants by RT-PCR.Furthermore,the sulphur-containing amino acids in transgenic tuber increase remarkably.

  5. Copper and cobalt recovery from pyrite ashes of a sulphuric acid plant.

    Science.gov (United States)

    Erust, Ceren; Akcil, Ata

    2016-06-01

    The pyrite ashes formed as waste material during the calcination of concentrated pyrite ore used for producing sulphuric acid not only has a high iron content but also contains economically valuable metals. These wastes, which are currently landfilled or dumped into the sea, cause serious land and environmental pollution problems owing to the release of acids and toxic substances. In this study, physical (sulphation roasting) and hydrometallurgical methods were evaluated for their efficacy to recover non-iron metals with a high content in the pyrite ashes and to prevent pollution thereby. The preliminary enrichment tests performed via sulphation roasting were conducted at different roasting temperatures and with different acid amounts. The leaching tests investigated the impact of the variables, including different solvents, acid concentrations and leach temperatures on the copper and cobalt leaching efficiency. The experimental studies indicated that the pre-enrichment via sulphation roasting method has an effect on the leaching efficiencies of copper and cobalt, and that approximate recoveries of 80% copper and 70% cobalt were achieved in the H2O2-added H2SO4 leaching tests.

  6. On the formation of sulphuric acid – amine clusters in varying atmospheric conditions and its influence on atmospheric new particle formation

    Directory of Open Access Journals (Sweden)

    I. K. Ortega

    2012-10-01

    Full Text Available Sulphuric acid is a key component in atmospheric new particle formation. However, sulphuric acid alone does not form stable enough clusters to initiate particle formation in atmospheric conditions. Strong bases, such as amines, have been suggested to stabilize sulphuric acid clusters and thus participate in particle formation. We modelled the formation rate of clusters with two sulphuric acid and two amine molecules (JA2B2 at varying atmospherically relevant conditions with respect to concentrations of sulphuric acid ([H2SO4], dimethylamine ([DMA] and trimethylamine ([TMA], temperature and relative humidity (RH. We also tested how the model results change if we assume that the clusters with two sulphuric acid and two amine molecules would act as seeds for heterogeneous nucleation of organic vapours (other than amines with higher atmospheric concentrations than sulphuric acid. The modelled formation rates JA2B2 were functions of sulphuric acid concentration with close to quadratic dependence, which is in good agreement with atmospheric observations of the connection between the particle formation rate and sulphuric acid concentration. The coefficients KA2B2 connecting the cluster formation rate and sulphuric acid concentrations as JA2B2=KA2B2[H2SO4]2 turned out to depend also on amine concentrations, temperature and relative humidity. We compared the modelled coefficients KA2B2 with the corresponding coefficients calculated from the atmospheric observations (Kobs from environments with varying temperatures and levels of anthropogenic influence. By taking into account the modelled behaviour of JA2B2 as a function of [H2SO4], temperature and RH, the atmospheric particle formation rate was reproduced more closely than with the traditional semi-empirical formulae based on sulphuric acid concentration only. The formation rates of clusters with two sulphuric acid and two amine molecules with different amine compositions (DMA or TMA or one of both had

  7. Upgrading of a Nigerian Ixiolite ore to Columbite by Sulphuric acid treatment

    Directory of Open Access Journals (Sweden)

    Alafara A Baba

    2016-09-01

    Full Text Available A quantitative leaching of a Nigerian Ixiolite ore in sulphuric acid medium was carried out and the effect of some parameters such as acid concentration, temperature and particle size was evaluated as a function of time. The experimental results obtained showed that the Ixiolite dissolution increases with increasing acid concentration, temperature, leaching time and, decreases with particle size. With 3 mol/L H2SO4 solution, 71.14% of the ore reacted within 120 minutes at 80°C.The kinetics of dissolution of the mineral was also examined and the observed effects of the operating variables on the leaching rate were consistent with the diffusion controlled kinetic model. The calculated activation energy for the leaching process was 24.40 kJ/mol with the reaction order of 0.5, supported the proposed model. Detailed characterization of the ore before and after leaching were carried out. At optimal leaching conditions, thermodynamic feasibility of the conversion of raw Ixiolite to Columbite of industrial value, as confirmed by X-ray diffraction (XRD technique is possible.

  8. Inhibiting Properties of Morpholine as Corrosion Inhibitor for Mild Steel in 2N Sulphuric Acid and Phosphoric Acid Medium

    Directory of Open Access Journals (Sweden)

    K. Jayanthi

    2012-01-01

    Full Text Available The inhibition effect of morpholine on the corrosion of mild steel in 2N sulphuric acid and phosphoric acid has been studied by mass loss and polarization techniques between 302K and 333K. The inhibition efficiency increased with increase in concentration. The corrosion rate increased with increase in temperature and decreased with increase in concentration of inhibitor compared to blank. The adsorption of inhibitor on the mild steel surface has been found to obey Temkin's adsorption isotherm. Potentiostatic polarization results reveal that morpholine act as mixed type inhibitor. The values of activation energy (Ea, free energy of adsorption (∆Gads, enthalpy of adsorption (∆H, and entropy of adsorption (∆S were also calculated.

  9. A quantitative test of infrared optical constants for supercooled sulphuric and nitric acid droplet aerosols

    Directory of Open Access Journals (Sweden)

    R. Wagner

    2003-05-01

    Full Text Available In situ Fourier transform infrared (FTIR extinction spectra of supercooled H2SO4/H2O and HNO3/H2O solution droplets were recorded in the large coolable aerosol chamber AIDA (Aerosol Interactions and Dynamics in the Atmosphere of Forschungszentrum Karlsruhe for a range of aerosol compositions and at temperatures extending down to 192 K. The measured spectra were quantitatively analysed in terms of aerosol composition and mass concentration by using Mie theory in combination with published refractive index data as input parameters. Simultaneously, total sulphuric acid and nitric acid mass concentrations from filter analysis and total water concentrations measured with the Lyman-a hygrometer of Forschungszentrum Jülich were used to calculate the aerosol composition at thermodynamic equilibrium inside the aerosol chamber. By comparing these measured aerosol parameters with those retrieved from the analysis of the FTIR spectra, the accuracy of the literature data sets of refractive indices could be assessed. In summary, four data sets were tested in the H2SO4/H2O system as well as two data sets in the HNO3/H2O system, partly revealing significant discrepancies in the retrieved aerosol properties. Potential explanations for these differences are discussed in this paper.

  10. A METHODOLOGY BASED ON AN ECOLOGICAL ECONOMY APPROACH FOR THE INTEGRATING MANAGEMENT OF THE SULPHUROUS WATER IN AN OIL REFINERY

    Directory of Open Access Journals (Sweden)

    Gabriel Orlando Lobelles Sardiñas

    2016-10-01

    Full Text Available Despite the current highly stringent international standards regulating the contaminating emissions to the environment, the Oil refinery of Cienfuegos is still generating liquid and gaseous emissions contaminating the environment. The construction of new units as part of the Refinery expansion leads to an increase of these emissions due to the lack of technologies for the reutilization of the sulphurous water. The objective of this paper is to propose a methodology for the integral management of the sulphurous residual water in the oil refining process, including the evaluation and selection of the most feasible technological variant to minimize the sulphur contamination of water and the resulting emissions during the process. The methodology is based on the ecological economy tools, allowing a comprehensible evaluation of six technological variants at the refinery of Cienfuegos. The Life Cycle Assessment was applied (ACV by its Spanish acronym, by means of the software SimaPro 7.1. It was evaluated through the Eco Speed Method, to minimize the possible uncertainty. An economic evaluation was performed, taking into account the external costs for a more comprehensive analysis, enabling, along with the ecological indicators, the selection of the best technological variant, achieving a methodology based on a comprehensive evaluation, and as a positive impact, the implementation of the chosen variant (V5, 98.27% of the process water was recovered, as well as the sulphur that recovered from 94 to 99.8 %, reducing the emissions from 12 200 to 120 mg/Nm3 as SO2.

  11. Interactions of meteoric smoke particles with sulphuric acid in the Earth's stratosphere

    Directory of Open Access Journals (Sweden)

    R. W. Saunders

    2012-01-01

    Full Text Available Nano-sized meteoric smoke particles (MSPs with iron-magnesium silicate compositions, formed in the upper mesosphere as a result of meteoric ablation, may remove sulphuric acid from the gas-phase above 40 km and may also affect the composition and behaviour of supercooled H2SO4-H2O droplets in the global stratospheric aerosol (Junge layer. This study describes a time-resolved spectroscopic analysis of the evolution of the ferric (Fe3+ ion originating from amorphous ferrous (Fe2+-based silicate powders dissolved in varying Wt % sulphuric acid (30–75% solutions over a temperature range of 223–295 K. Complete dissolution of the particles was observed under all conditions. The first-order rate coefficient for dissolution decreases at higher Wt % and lower temperature, which is consistent with the increased solution viscosity limiting diffusion of H2SO4 to the particle surfaces. Dissolution under stratospheric conditions should take less than a week, and is much faster than the dissolution of crystalline Fe2+ compounds. The chemistry climate model UMSLIMCAT (based on the UKMO Unified Model was then used to study the transport of MSPs through the middle atmosphere. A series of model experiments were performed with different uptake coefficients. Setting the concentration of 1.5 nm radius MSPs at 80 km to 3000 cm−3 (based on rocket-borne charged particle measurements, the model matches the reported Wt % Fe values of 0.5–1.0 in Junge layer sulphate particles, and the MSP optical extinction between 40 and 75 km measured by a satellite-borne spectrometer, if the global meteoric input rate is about 20 t d−1. The model indicates that an uptake coefficient ≥0.01 is required to account for the observed two orders of magnitude depletion of H2SO4 vapour above 40 km.

  12. Interactions of meteoric smoke particles with sulphuric acid in the Earth's stratosphere

    Directory of Open Access Journals (Sweden)

    R. W. Saunders

    2012-05-01

    Full Text Available Nano-sized meteoric smoke particles (MSPs with iron-magnesium silicate compositions, formed in the upper mesosphere as a result of meteoric ablation, may remove sulphuric acid from the gas-phase above 40 km and may also affect the composition and behaviour of supercooled H2SO4-H2O droplets in the global stratospheric aerosol (Junge layer.

    This study describes a time-resolved spectroscopic analysis of the evolution of the ferric (Fe3+ ion originating from amorphous ferrous (Fe2+-based silicate powders dissolved in varying Wt % sulphuric acid (30–75 % solutions over a temperature range of 223–295 K. Complete dissolution of the particles was observed under all conditions. The first-order rate coefficient for dissolution decreases at higher Wt % and lower temperature, which is consistent with the increased solution viscosity limiting diffusion of H2SO4 to the particle surfaces. Dissolution under stratospheric conditions should take less than a week, and is much faster than the dissolution of crystalline Fe2+ compounds.

    The chemistry climate model UMSLIMCAT (based on the UKMO Unified Model was then used to study the transport of MSPs through the middle atmosphere. A series of model experiments were performed with different uptake coefficients. Setting the concentration of 1.5 nm radius MSPs at 80 km to 3000 cm−3 (based on rocket-borne charged particle measurements, the model matches the reported Wt % Fe values of 0.5–1.0 in Junge layer sulphate particles, and the MSP optical extinction between 40 and 75 km measured by a satellite-borne spectrometer, if the global meteoric input rate is about 20 tonnes per day. The model indicates that an uptake coefficient ≥0.01 is required to account for the observed two orders of magnitude depletion of H2SO4 vapour above 40 km.

  13. Effect of aliphatic, monocarboxylic, dicarboxylic, heterocyclic and sulphur-containing amino acids on Leishmania spp. chemotaxis.

    Science.gov (United States)

    Diaz, E; Zacarias, A K; Pérez, S; Vanegas, O; Köhidai, L; Padrón-Nieves, M; Ponte-Sucre, A

    2015-11-01

    In the sand-fly mid gut, Leishmania promastigotes are exposed to acute changes in nutrients, e.g. amino acids (AAs). These metabolites are the main energy sources for the parasite, crucial for its differentiation and motility. We analysed the migratory behaviour and morphological changes produced by aliphatic, monocarboxylic, dicarboxylic, heterocyclic and sulphur-containing AAs in Leishmania amazonensis and Leishmania braziliensis and demonstrated that L-methionine (10-12 m), L-tryptophan (10-11 m), L-glutamine and L-glutamic acid (10-6 m), induced positive chemotactic responses, while L-alanine (10-7 m), L-methionine (10-11 and 10-7 m), L-tryptophan (10-11 m), L-glutamine (10-12 m) and L-glutamic acid (10-9 m) induced negative chemotactic responses. L-proline and L-cysteine did not change the migratory potential of Leishmania. The flagellum length of L. braziliensis, but not of L. amazonensis, decreased when incubated in hyperosmotic conditions. However, chemo-repellent concentrations of L-alanine (Hypo-/hyper-osmotic conditions) and L-glutamic acid (hypo-osmotic conditions) decreased L. braziliensis flagellum length and L-methionine (10-11 m, hypo-/hyper-osmotic conditions) decreased L. amazonensis flagellum length. This chemotactic responsiveness suggests that Leishmania discriminate between slight concentration differences of small and structurally closely related molecules and indicates that besides their metabolic effects, AAs play key roles linked to sensory mechanisms that might determine the parasite's behaviour.

  14. Solubilities and transport properties of the stratospheric sulphuric acid aerosol: laboratory investigations using extremely thin sulphuric acid films. Final report; Loesungs- und Transporteigenschaften des stratosphaerischen Schwefelsaeureaerosols: Laboruntersuchungen an extrem duennen Schwefelsaeurefilmen. Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Schurath, U.; Proksch, V.

    2000-04-17

    We have developed a procedure to measure solubilities, diffusion coefficients and rate constants (oxidation; hydrolysis) of trace gases in sulphuric acid at stratospheric temperatures. The results will lead to a better understanding and quantification of heterogeneous reactions in/on sulphuric acid aerosol particles in stratospheric models. Sulphuric acid (19-83 wt-%) is deposited as a thin film (1-3 {mu}m) on the inner surface of a capillary column (i.d. 530 {mu}m). The trace gas under study is injected into the carrier gas which passes through the column. Solubilities, diffusion coefficients and rate constants for the hydrolysis/oxidation of the trace gases in the sulphuric acid film can be deduced from the retention times, shapes and areas of the trace gas peaks which are detected by a mass spectrometer. (orig.) [German] Es wurde ein Verfahren zur Messung von Loeslichkeiten, Diffusionskoeffizienten und Ratenkonstanten (Oxidation; Hydrolyse) von Spurengasen in Schwefelsaeure bei stratosphaerischen Temperaturen entwickelt. Die Messergebnisse dienen dem besseren Verstaendnis und der Quantifizierung von heterogenen Reaktionen am stratosphaerischen Schwefelsaeure-Aerosol in Stratosphaerenmodellen. Die Schwefelsaeure (19-83 Gew.%) befindet sich als duenner Film (1-3 {mu}m) auf der Innenseite einer Kapillarsaeule (ID=530 {mu}m), die von einem Traegergas und dem zu untersuchenden Spurengas durchstroemt wird. Die Kapillarsaeule wird in einem Kryostaten auf 186-263 K gekuehlt. Aus der Ankunftszeit, Form und Flaeche von Spurengaspeaks an einem Massenspektrometer-Detektor koennen Loeslichkeiten und Diffusionskoeffizienten sowie Ratenkonstanten fuer die Hydrolyse/Oxidation von Spurengasen im Schwefelsaeurefilm bestimmt werden. (orig.)

  15. Oxidation states of molybdenum in oxide films formed in sulphuric acid and sodium hydroxide

    Energy Technology Data Exchange (ETDEWEB)

    Okonkwo, I.A.; Doff, J.; Baron-Wiechec, A. [Corrosion and Protection Centre, School of Materials, The University of Manchester, Manchester M13 9PL (United Kingdom); Jones, G. [Waters Corporation, Floats Rd, Roundthorn Ind. Est., Manchester M23 9LZ (United Kingdom); Koroleva, E.V. [Corrosion and Protection Centre, School of Materials, The University of Manchester, Manchester M13 9PL (United Kingdom); Skeldon, P., E-mail: p.skeldon@manchester.ac.uk [Corrosion and Protection Centre, School of Materials, The University of Manchester, Manchester M13 9PL (United Kingdom); Thompson, G.E. [Corrosion and Protection Centre, School of Materials, The University of Manchester, Manchester M13 9PL (United Kingdom)

    2012-07-31

    X-ray photoelectron spectroscopy is used to investigate the oxidation states of molybdenum in thin films formed potentiostatically, over a range of potentials, in either 1 mol dm{sup -3} H{sub 2}SO{sub 4} or 10 mol dm{sup -3} NaOH at 20 Degree-Sign C. Mo 3d spectra suggested that MoO{sub 2} and Mo(OH){sub 2} were the main components of the films, with smaller amounts of MoO{sub 3} and possibly Mo{sub 2}O{sub 5}. O 1s spectra indicated the presence of oxygen as oxide and hydroxide species and as bound water. Ion beam analysis revealed the formation of thin films at all potentials, with significant losses of oxidized molybdenum to the electrolyte. - Highlights: Black-Right-Pointing-Pointer Oxides are formed on molybdenum in sulphuric acid and sodium hydroxide solutions. Black-Right-Pointing-Pointer Molybdenum IV and VI are identified by XPS, with MoO2 species dominating. Black-Right-Pointing-Pointer Thicknesses of films are determined by ion beam analysis for a range of potentials. Black-Right-Pointing-Pointer Films form at low efficiency due to loss of molybdenum species to electrolyte.

  16. Effects of gaseous sulphuric acid on diesel exhaust nanoparticle formation and characteristics.

    Science.gov (United States)

    Rönkkö, Topi; Lähde, Tero; Heikkilä, Juha; Pirjola, Liisa; Bauschke, Ulrike; Arnold, Frank; Schlager, Hans; Rothe, Dieter; Yli-Ojanperä, Jaakko; Keskinen, Jorma

    2013-10-15

    Diesel exhaust gaseous sulphuric acid (GSA) concentrations and particle size distributions, concentrations, and volatility were studied at four driving conditions with a heavy duty diesel engine equipped with oxidative exhaust after-treatment. Low sulfur fuel and lubricant oil were used in the study. The concentration of the exhaust GSA was observed to vary depending on the engine driving history and load. The GSA affected the volatile particle fraction at high engine loads; higher GSA mole fraction was followed by an increase in volatile nucleation particle concentration and size as well as increase of size of particles possessing nonvolatile core. The GSA did not affect the number of nonvolatile particles. At low and medium loads, the exhaust GSA concentration was low and any GSA driven changes in particle population were not observed. Results show that during the exhaust cooling and dilution processes, besides critical in volatile nucleation particle formation, GSA can change the characteristics of all nucleation mode particles. Results show the dual nature of the nucleation mode particles so that the nucleation mode can include simultaneously volatile and nonvolatile particles, and fulfill the previous results for the nucleation mode formation, especially related to the role of GSA in formation processes.

  17. Effect of film thickness and filler properties on sulphuric acid permeation in various commercially available epoxy mortar coatings.

    Science.gov (United States)

    Valix, M; Mineyama, H; Chen, C; Cheung, W H; Shi, J; Bustamante, H

    2011-01-01

    The performance of various commercially available epoxy mortar coatings was compared by measuring their sulphuric acid diffusivity. Apparent diffusivities, which were measured gravimetrically, were found to be dependent on coating tortuosity. In composite materials like epoxy mortars, the tortuosity was determined by filler properties and polymer alignment. Tortuosity was found to depend on the filler size, their dispersion, filler aspect ratio and concentration. The order and greater alignment of polymer aggregates, which characterises thinner coatings effects higher tortuosity and thus lower permeabilities. The result is that sulphuric acid diffusivities were observed to increase with coating thickness, which challenges the notion that greater coating thicknesses provide greater protection or environmental barrier. The effect of film thickness and filler properties observed in this study has significant implications to the current selection of coatings and sewer protection.

  18. Isolation and fractionation of soil humin using alkaline urea and dimethylsulphoxide plus sulphuric acid

    Science.gov (United States)

    Song, Guixue; Hayes, Michael H. B.; Novotny, Etelvino H.; Simpson, Andre J.

    2011-01-01

    Humin, the most recalcitrant and abundant organic fraction of soils and of sediments, is a significant contributor to the stable carbon pool in soils and is important for the global carbon budget. It has significant resistance to transformations by microorganisms. Based on the classical operational definition, humin can include any humic-type substance that is not soluble in water at any pH. We demonstrate in this study how sequential exhaustive extractions with 0.1 M sodium hydroxide (NaOH) + 6 M urea, followed by dimethylsulphoxide (DMSO) + 6% ( v/ v) sulphuric acid (H2SO4) solvent systems, can extract 70-80% of the residual materials remaining after prior exhaustive extractions in neutral and aqueous basic media. Solid-state 13C NMR spectra have shown that the components isolated in the base + urea system were compositionally similar to the humic and fulvic acid fractions isolated at pH 12.6 in the aqueous media. The NMR spectra indicated that the major components isolated in the DMSO + H2SO4 medium had aliphatic hydrocarbon associated with carboxyl functionalities and with lesser amounts of carbohydrate and peptide and minor amounts of lignin-derived components. The major components will have significant contributions from long-chain fatty acids, waxes, to cuticular materials. The isolates in the DMSO + H2SO4 medium were compositionally similar to the organic components that resisted solvation and remained associated with the soil clays. It is concluded that the base + urea system released humic and fulvic acids held by hydrogen bonding or by entrapment within the humin matrix. The recalcitrant humin materials extracted in DMSO + H2SO4 are largely biological molecules (from plants and the soil microbial population) that are likely to be protected from degradation by their hydrophobic moieties and by sorption on the soil clays. Thus, the major components of humin do not satisfy the classical definitions for humic substances which emphasise that these arise from

  19. Removal of Pb(II) ions from aqueous solutions by sulphuric acid-treated wheat bran.

    Science.gov (United States)

    Ozer, A

    2007-03-22

    Sulphuric acid-treated wheat bran (STWB) was used as an adsorbent to remove Pb(II) ions from aqueous solution. It was observed that the adsorption yield of Pb(II) ions was found to be pH dependent. The equilibrium time for the process was determined as 2h. STWB gave the highest adsorption yield at around pH 6.0. At this pH, adsorption percentage for an initial Pb(II) ions concentration of 100mg/L was found to be 82.8 at 25 degrees C for contact time of 2h. The equilibrium data obtained at different temperatures fitted to the non-linear form of Langmuir, Freundlich and Redlich-Peterson and linear form of Langmuir and Freundlich models. Isotherm constants were calculated and compared for the models used. The maximum adsorption capacity (q(max)) which was obtained linear form of Langmuir model increased from 55.56 to 79.37mg/g with increasing temperature from 25 to 60 degrees C. Similar trend was observed for other isotherm constants related to the adsorption capacity. Linear form of Langmuir isotherm data was evaluated to determine the thermodynamic parameters for the process. Thermodynamic parameters show that adsorption process of Pb(II) ions is an endothermic and more effective process at high temperatures. The pseudo nth order kinetic model was successfully applied to the kinetic data and the order (n) of adsorption reaction was calculated at the range from 1.711 to 1.929. The values of k(ad) were found to be 5.82x10(-4) and 21.81x10(-4)(min(-1))(mg/g)(1-n) at 25 and 60 degrees C, respectively. Activation energy was determined as 29.65kJ/mol for the process. This suggest that the adsorption Pb(II) ions by STWB is chemically controlled.

  20. Cellulose sulphuric acid as a biodegradable catalyst for conversion of aryl amines into azides at room temperature under mild conditions

    Indian Academy of Sciences (India)

    Firouzeh Nesmati; Ali Elhampour

    2012-07-01

    This article describes simple and efficient method for the diazotization and azidation of different aromatic amines over cellulose sulphuric acid, sodium nitrite and sodium azide under mild conditions at room temperature. Various aryl amines possessing electron-withdrawing groups or electron-donating groups have been converted into the corresponding aryl azides with 71-99% yields. The use of mild reaction conditions, avoids the use of harmful acids and toxic solvents and short reaction times are advantages of this methodology. The selected catalyst is found to be highly efficient and recyclable.

  1. Polarographic study of complexing in the molybdenum (6) - mandelic acid - sulphuric acid system

    Energy Technology Data Exchange (ETDEWEB)

    Zaitsev, P.M.; Zaitseva, Z.V.; Zhdanov, S.I.; Nikolaeva, T.D. (Vsesoyuznyj Nauchno-Issledovatel' skij Inst. Okhrany Truda, Moscow (USSR); Vsesoyuznyj Nauchno-Issledovatel' skij Inst. Khimicheskikh Reaktivov i Osobo Chistykh Veshchestv, Moscow (USSR))

    1980-09-01

    The studies of polarographic behaviour of molybdenum (6) in 0.05-2.5 M H/sub 2/SO/sub 4/ solutions, containing mandelic acid (HL), has shown that molybdenum (6) is reduced via two steps in the presence of HL. One electron is transferred in 0.05 M H/sub 2/SO/sub 4/ during the first step and two during the second one; one electron during each step is transferred if Csub(Hsub(2)SOsub(4))>=0.5 M. Such a difference is suggested to be due to the formation of a mixed-ligand complex MoO/sub 2/xHLx(H/sub 2/SO/sub 4/)/sup +/ which is reduced stepwise, one electron participating at each step. The complex formation is slow. The complex formation constant has been calculated to be 30+-2.7.

  2. The isotherm slope. A criterion for studying the adsorption mechanism of benzotriazole on copper in sulphuric acid

    Energy Technology Data Exchange (ETDEWEB)

    Bastidas, D. M.; Gomez, P. P.; Cano, E.

    2005-07-01

    The adsorption of benzotriazole (BTA) on copper surfaces in 0.001, 0.005 and 0.01 M concentrations of sulphuric acid was investigated using gravimetric measurements. BTA was tested in concentrations from 1x10''-5 to 1x10''-1 M at temperatures from 298 to 328 K. The adsorption mechanism is discussed in terms of applicability of the conventional Frumkin, Bockris-Swinkels and Kastening-Holleck isotherms, among others. The best fit was obtained using the Frumkin isotherm model. the projected molecular area of BTA was calculated to elucidate inhibitor orientation in the adsorption process. (Author) 38 refs.

  3. The isotherm slope. A criterion for studying the adsorption mechanism of benzotriazole on copper in sulphuric acid

    OpenAIRE

    Bastidas, D. M.; Gómez, R. R.; Cano, E.

    2005-01-01

    The adsorption of benzotriazole (BTA) on copper surfaces in 0.001, 0.005 and 0.01 M concentrations of sulphuric acid was investigated using gravimetric measurements. BTA was tested in concentrations from 1x10-5 to 1x10-1 M at temperatures from 298 to 328 K. The adsorption mechanism is discussed in terms of applicability of the conventional Frumkin, Bockris-Swinkels and Kastening-Holleck isotherms, among others. The best fit was obtained using the ...

  4. On the formation of sulphuric acid-amine clusters in varying atmospheric conditions and its influence on atmospheric new particle formation

    Directory of Open Access Journals (Sweden)

    P. Paasonen

    2012-05-01

    Full Text Available Sulphuric acid is a key component in atmospheric new particle formation. However, sulphuric acid alone does not form stable enough clusters to initiate particle formation in atmospheric conditions. Strong bases, such as amines, have been suggested to stabilize sulphuric acid clusters and thus participate in particle formation. We modelled the formation rate of clusters with two sulphuric acid and two amine molecules (JA2B2 at varying atmospherically relevant conditions with respect to concentrations of sulphuric acid ([H2SO4], dimethylamine ([DMA] and trimethylamine ([TMA], temperature and relative humidity (RH. The modelled formation rates JA2B2 were functions of sulphuric acid concentration with close to quadratic dependence, which is in good agreement with atmospheric observations of the connection between the particle formation rate and sulphuric acid concentration. The coefficients KA2B2 connecting the cluster formation rate and sulphuric acid concentrations as JA2B2 = KA2B2[H2SO4]2 turned out to depend also on amine concentrations, temperature and relative humidity. We tested how the model results change if the clusters with two sulphuric acid and two amine molecules are assumed to act as seeds for heterogeneous nucleation of organic vapours (other than amines with higher atmospheric concentrations than sulphuric acid. We also compared the modelled coefficients KA2B2 with the corresponding coefficients calculated from the atmospheric observations (Kobs from environments with varying temperatures and levels of anthropogenic influence. By taking into account the modelled behaviour of JA2B2 as a function of [H2SO4], temperature and RH, the atmospheric particle formation rate was reproduced more closely than with the

  5. Optimization of the 3-Point Bending Failure of Anodized Aluminum Formed in Tartaric/Sulphuric Acid Using Doehlert Design

    Science.gov (United States)

    Bensalah, W.; Feki, M.; De-Petris Wery, M.; Ayedi, H. F.

    2015-02-01

    The bending failure of anodized aluminum in tartaric/sulphuric acid bath was modeled using Doehlert design. Bath temperature, anodic current density, sulphuric acid, and tartaric acid concentrations were retained as variables. Thickness measurements and 3-point bending experiments were conducted. The deflection at failure ( D f) and the maximum load ( F m) of each sample were, then, deducted from the corresponding flexural responses. The treatment of experimental results has established mathematical models of second degree reflecting the relation of cause and effect between the factors and the studied properties. The optimum path study of thickness, deflection at failure, and maximum load, showed that the three optima were opposite. Multicriteria optimization using the desirability function was achieved in order to maximize simultaneously the three responses. The optimum conditions were: C tar = 18.2 g L-1, T = 17.3 °C, J = 2.37 A dm-2, C sul = 191 g L-1, while the estimated response values were e = 57.7 µm, D f = 5.6 mm, and F m = 835 N. Using the established models, a mathematical correlation was found between deflection at failure and thickness of the anodic oxide layer. Before bending tests, aluminum oxide layer was examined by scanning electron microscopy (SEM) and atomic force microscopy. After tests, the morphology and the composition of the anodic oxide layer were inspected by SEM, optical microscopy, and glow-discharge optical emission spectroscopy.

  6. THE EFFECT OF SULPHURIC ACID CONCENTRATION ON SOLVENT EXTRACTION OF ReO4 - BY THE LONG-CHAIN ALIPHATIC TERTIARY AMINES AND ALCOHOLS

    Directory of Open Access Journals (Sweden)

    Aleksander G. Kasikov

    2010-06-01

    Full Text Available The effect of sulphuric acid concentration on solvent extraction of ReO4- by the long-chain aliphatic tertiary amines and alcohols in a wide range of H2SO4 concentrations in initial solutions is discussed. It has been established that the influence of the sulphuric acid concentration on rhenium solvent extraction is largely due to the extraction process mechanism. In the case of the anion-exchange mechanism, ReO4- is best extracted from weakly acidic solutions, whereas when the hydrate-solvate mechanism takes place – from solutions containing 4-7 mole/l H2SO4.

  7. 发烟硫酸浓度互换公式的推导%Derivation about Concentrations Exchanging Formula of Fuming Sulphuric Acid

    Institute of Scientific and Technical Information of China (English)

    谭靖辉; 唐淑贞

    2011-01-01

    指出发烟硫酸是游离态SO3的H2SO4溶液,运用质量守恒定律对发烟硫酸浓度互换公式进行了推导,阐述了使用该公式的注意事项。%Fuming sulphuric acid was regarded as SO3 of free state in sulfuric acid solution,concentrations exchanging formula of fuming sulphuric acid was deduced by mass conservation law,attentions of formula were expounded.

  8. Hydrofluoric–nitric–sulphuric-acid surface treatment of tungsten for carbon fibre-reinforced composite hybrids in space applications

    Energy Technology Data Exchange (ETDEWEB)

    Kanerva, M., E-mail: Mikko.Kanerva@aalto.fi [Aalto University, School of Engineering, Department of Applied Mechanics, P.O.B. 14300, FI-00076 Aalto (Finland); Johansson, L.-S.; Campbell, J.M. [Aalto University, School of Chemical Technology, Department of Forest Products Technology, P.O.B. 16300, FI-00076 Aalto (Finland); Revitzer, H. [Aalto University, School of Chemical Technology, Department of Chemistry, P.O.B. 16300, FI-00076 Aalto (Finland); Sarlin, E. [Tampere University of Technology, Department of Materials Science, P.O.B. 589, FI-33101 Tampere (Finland); Brander, T.; Saarela, O. [Aalto University, School of Engineering, Department of Applied Mechanics, P.O.B. 14300, FI-00076 Aalto (Finland)

    2015-02-15

    Highlights: • XPS and AFM analysis of the effect of hydrofluoric–nitric–sulphuric-acid on tungsten. • Dreiling's model established 54.4% thinning of WO{sub 3} due to 67 s treatment. • Strain energy release rate increased ≈8.4 J/m{sup 2} at the interface. • Failure loci analysis expressed the oxide and carbon fibre surfaces as weak points. - Abstract: Hybrid material systems, such as combinations of tungsten foils and carbon fibre-reinforced plastic (CFRP), are replacing metal alloy concepts in spacecraft enclosures. However, a good adhesion between the tungsten oxide scale and the epoxy resin used is required. Here, the effects of a hydrofluoric–nitric–sulphuric-acid (HFNS) treatment on tungsten oxides and subsequent adhesion to CFRP are analysed using atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and fracture testing. The work shows that HFNS treatment results in decreased oxygen content, over 50% thinner tungsten trioxide (WO{sub 3}) layer and increased nano-roughness on thin tungsten foils. Fracture testing established a 39% increase in the average critical strain for tungsten–CFRP specimens after HFNS treatment was carried out on tungsten. The effect of the oxide scale modification regarding the critical strain energy release rate was ΔG{sub c}≈ 8.4 J/m{sup 2}.

  9. Dilution Methods in Flow Injection Analysis. Evaluation of Different Approaches as Exemplified for the Determination of Nitrosyl in Concentrated Sulphuric Acid

    DEFF Research Database (Denmark)

    Jørgensen, Ulla Vang; Nielsen, Steffen; Hansen, Elo Harald

    1998-01-01

    Instigated by developing a flow injection procedure for assay of nitrosyl in concentrated sulphuric acid, different approaches for reliable and robust on-line dilution in FIA were evaluated. These comprised the application of mixing tees in conjunction with mixing coils (including knotted reactors...... approach the criteria stipulated were that the procedure should allow a dilution factor of approximately 100, yet without excessive zone spreading, so that it, on one hand, effectively could eliminate the pronounced Schlieren effect encountered when mixing concentrated sulphuric acid with an aqueous...... in conjunction with knotted reactors of relatively large internal diameter (1.5 mm). The optimized FI-manifold was used with the Griess method for the spectrophotometric assay of nitrosyl (nitrite) in standards prepared in the matrix of concentrated sulphuric acid (detection limit 0.16 mg/l NO+-N (3s...

  10. The contribution of sulphuric acid to atmospheric particle formation and growth: a comparison between boundary layers in Northern and Central Europe

    Directory of Open Access Journals (Sweden)

    V. Fiedler

    2005-01-01

    Full Text Available Atmospheric gaseous sulphuric acid was measured and its influence on particle formation and growth was investigated building on aerosol data. The measurements were part of the EU-project QUEST and took place at two different measurement sites in Northern and Central Europe (Hyytiälä, Finland, March-April 2003 and Heidelberg, Germany, March-April 2004. From a comprehensive data set including sulphuric acid, particle number size distributions and meteorological data, particle growth rates, particle formation rates and source rates of condensable vapors were inferred. Growth rates were determined in two different ways, from particle size distributions as well as from a so-called timeshift analysis. Moreover, correlations between sulphuric acid and particle number concentration between 3 and 6 nm were examined and the influence of air masses of different origin was investigated. Measured maximum concentrations of sulphuric acid were in the range from 1x106 to 16x106cm-3. The gaseous sulphuric acid lifetime with respect to condensation on aerosol particles ranged from 2 to 33min in Hyytiälä and from 0.5 to 8 min in Heidelberg. Most calculated values (growth rates, formation rates, vapor source rates were considerably higher in Central Europe (Heidelberg, due to the more polluted air and higher preexistent aerosol concentrations. Close correlations between H2SO4 and nucleation mode particles (size range: 3-6 nm were found on most days at both sites. The percentage contribution of sulphuric acid to particle growth was below 10% at both places and to initial growth below 20%. An air mass analysis indicated that at Heidelberg new particles were formed predominantly in air advected from southwesterly directions.

  11. Investigating the significance of zero-point motion in small molecular clusters of sulphuric acid and water

    Energy Technology Data Exchange (ETDEWEB)

    Stinson, Jake L.; Kathmann, Shawn M.; Ford, Ian J.

    2014-01-14

    The nucleation of particles from trace gases in the atmosphere is an important source of cloud condensation nuclei (CCN), and these are vital for the formation of clouds in view of the high supersaturations required for homogeneous water droplet nucleation. The methods of quantum chemistry have increasingly been employed to model nucleation due to their high accuracy and efficiency in calculating configurational energies; and nucleation rates can be obtained from the associated free energies of particle formation. However, even in such advanced approaches, it is typically assumed that the nuclei have a classical nature, which is questionable for some systems. The importance of zero-point motion (also known as quantum nuclear dynamics) in modelling small clusters of sulphuric acid and water is tested here using the path integral molecular dynamics (PIMD) method at the density functional theory (DFT) level of theory. We observe a small zero-point effect on the the equilibrium structures of certain clusters. One configuration is found to display a bimodal behaviour at 300 K in contrast to the stable ionised state suggested from a zero temperature classical geometry optimisation. The general effect of zero-point motion is to promote the extent of proton transfer with respect to classical behaviour. We thank Prof. Angelos Michaelides and his group in University College London (UCL) for practical advice and helpful discussions. This work benefited from interactions with the Thomas Young Centre through seminar and discussions involving the PIMD method. SMK was supported by the U.S. Department of Energy, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences, and Biosciences. JLS and IJF were supported by the IMPACT scheme at UCL and by the U.S. Department of Energy, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences, and Biosciences. We are grateful for use of the UCL Legion High Performance Computing Facility and the

  12. 大型硫磺制酸废热回收设备的设计与布置%The design and layout of waste heat recovery equipment in large sulphur-burning sulphuric acid plants

    Institute of Scientific and Technical Information of China (English)

    王渭清

    2012-01-01

    介绍了大型硫磺制酸废热回收系统选用的不同工艺流程、设备和蒸汽参数,详细分析了废热锅炉、过热器、省煤器等设备的选型、结构、参数、尺寸、材料,并对废热回收系统的设备、管道布置及防腐保温等方面提出了优化措施。%The processes, equipment and steam parameters of waste heat recovery system used in large-scale sulphur-burning sulphuric acid plants are described. A detail analysis of the structure, parameters, dimensions and materials of waste heat boiler, superheater and economizer is made and optimization measures of equipment and pipe layout, corrosion protection and insulation are proposed.

  13. A new form of sulphur in coal: the discovery of an iron-sulphur coordination compound

    Energy Technology Data Exchange (ETDEWEB)

    Baruah, M.K.; Gogoi, P.C. [NNS College, Titabar (India). Dept. of Chemistry

    1998-07-01

    An iron-sulphur coordination compound in coal has been identified for the first time. Isolation of the compound from a high sulphur Indian coal sample was performed by extracting with tetrahydrofuran followed by methanol and ultimately separated by thin layer chromatography. Characterization of the compound by proton n.m.r., i.r., u.v. and chemical analyses of iron and sulphur reveals that iron atoms are bonded to thiophenic, aliphatic and inorganic sulphur atoms. Geochemical studies have revealed that the main sources of sulphur are inorganic and sulphur amino acids mostly cysteine, cystine and methionine. Identification of the coordination compound has confirmed the nature and occurrence of secondary sulphur in coal. This compound is considered to be a new form of sulphur because it is neither purely pyritic nor organic sulphur. The discovery of the Fe-S coordination compound is a great concern for the determination of the sulphur forms in coal. 50 refs., 3 figs.

  14. SUBSTITUTION REACTION OF HYDROXY OF CITRONELLOL WITH CHLORIDE USING A MIXTURE OF AMMONIUM CHLORIDE AND SULPHURIC ACID

    Directory of Open Access Journals (Sweden)

    Endah Sayekti

    2016-08-01

    Full Text Available Substitution reaction of hydroxy of citronellol with chloride using a mixture of ammonium chloride (NH4Cl and sulphuric acid (H2SO4 has been conducted. The citronellol was obtained from the reduction of citronellal using sodium borohydride (NaBH4 at room temperature for 30 minutes. Substitution of hydroxy of citronellol with chloride ion was carried out at 80 oC and molarity ratio of citronellol and NH4Cl 1:1, 1:2; 1:3; and 1:4 respectively. Identification of the product by gas chromatography-mass spectrometry (GC-MS showed that the substitution reaction produced 2-isopropyl-5-methyl-1-chlorocyclohexane compound with rendemen 64,49 % in mol ratio of 1:4. The infra red (IR analysis showed that there was a vibration at wave number 763 cm-1 which is a typical C-Cl vibrations.

  15. Hydrofluoric-nitric-sulphuric-acid surface treatment of tungsten for carbon fibre-reinforced composite hybrids in space applications

    Science.gov (United States)

    Kanerva, M.; Johansson, L.-S.; Campbell, J. M.; Revitzer, H.; Sarlin, E.; Brander, T.; Saarela, O.

    2015-02-01

    Hybrid material systems, such as combinations of tungsten foils and carbon fibre-reinforced plastic (CFRP), are replacing metal alloy concepts in spacecraft enclosures. However, a good adhesion between the tungsten oxide scale and the epoxy resin used is required. Here, the effects of a hydrofluoric-nitric-sulphuric-acid (HFNS) treatment on tungsten oxides and subsequent adhesion to CFRP are analysed using atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and fracture testing. The work shows that HFNS treatment results in decreased oxygen content, over 50% thinner tungsten trioxide (WO3) layer and increased nano-roughness on thin tungsten foils. Fracture testing established a 39% increase in the average critical strain for tungsten-CFRP specimens after HFNS treatment was carried out on tungsten. The effect of the oxide scale modification regarding the critical strain energy release rate was ΔGc≈ 8.4 J/m2.

  16. Waste sulphuric acid regeneration plants and on-site services%废硫酸再生装置与现场服务

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    Waste sulphuric acid regeneration has matured to provide a robust and reliable way for recycling the waste sulphuric acid using a variety of sources. Design features of MECS waste sulphuric acid regeneration plants and on-site service for sulphuric users provided by Rhodia are described. Rhodia's service includes a patented storage tank cleaning technology, which can not only clean out and recover acid sludge from storage tanks, but also avoid confined space entry.%废硫酸再生技术已经成熟,为回收利用各种来源的废硫酸提供了一条稳健、可靠的途径。主要阐述了MECS废酸再生装置的设计特点和罗地亚为硫酸用户提供的现场服务。罗地亚的现场服务包括一种专利储罐清洗技术,该技术不但可清除并回收罐底酸泥,而且可避免受限空间的进入。

  17. SOSA – a new model to simulate the concentrations of organic vapours and sulphuric acid inside the ABL – Part 1: Model description and initial evaluation

    DEFF Research Database (Denmark)

    Boy, M.; Sogachev, Andrey; Lauros, J.

    2010-01-01

    Chemistry in the atmospheric boundary layer (ABL) is controlled by complex processes of surface fluxes, flow, turbulent transport, and chemical reactions. We present a new model SOSA (model to simulate the concentration of organic vapours and sulphuric acid) and attempt to reconstruct the emissions...

  18. SOSA – a new model to simulate the concentrations of organic vapours and sulphuric acid inside the ABL – Part 1: Model description and initial evaluation

    DEFF Research Database (Denmark)

    Boy, M.; Sogachev, Andrey; Lauros, J.

    2011-01-01

    Chemistry in the atmospheric boundary layer (ABL) is controlled by complex processes of surface fluxes, flow, turbulent transport, and chemical reactions. We present a new model SOSA (model to simulate the concentration of organic vapours and sulphuric acid) and attempt to reconstruct the emissions...

  19. INVESTIGATION OF THE OPTIMUM DISSOLUTION TEMPERATURES OF PHOSPHORUS IN SULPHURIC, NITRIC AND OXALIC ACID SOLUTIONS DURING LEACHING OF IRON OXIDE ORE

    Directory of Open Access Journals (Sweden)

    C. I. NWOYE

    2009-12-01

    Full Text Available Studies were carried out to determine the optimum dissolution temperatures of phosphorus in oxalic, nitric and sulphuric acid solutions during leaching of iron oxide ore. Phosphorus dissolution rates and dissolution per unit rise in temperature were determined and compared to ascertain the preferred acid in terms of effective dephosphorization of iron oxide ore using leaching process. The results of the investigation show that the optimum dissolution temperatures of phosphorus in these acids were found to be 45, 55 and 70ºC respectively. Phosphorus dissolutions per unit rise in temperature in these acid solutions during the increasing and decreasing stage of dissolution were 9.4 and -3.07 mg/kg/ºC 2.88 and -4.7 mg/kg/ºC and also 2.16 and -7.95 mg/kg/ºC respectively. Phosphorus dissolution rates in these acid solutions during the increasing and decreasing stage of dissolution were also determined as 0.67 and -0.13 mg/kg/s, 0.14 and -0.19 mg/kg/s and also 0.1 and 0.44 mg/kg/s for oxalic, nitric and sulphuric acid solutions respectively. This confers to oxalic acid a better dissolution power on phosphorus over nitric and sulphuric acid, followed by nitric acid.

  20. Alkalis scrubbing vs sulphuric acid production with Claus tail gases%克劳斯尾气碱洗涤与生产硫酸的比较

    Institute of Scientific and Technical Information of China (English)

    M. RAMESHNI; 金苏闽(译)

    2012-01-01

    为使克劳斯硫回收装置的硫回收率达到100%,讨论并比较了碱洗涤与生产硫酸这2种尾气处理技术。这2种技术都可用于满足最苛刻的排放要求,生产硫酸的成本略低。但除了成本之外,还应考虑炼油厂的总体布置、原油类型及硫和氮含量、产品酸的市场需求、所需公用工程的供应等因素。%In order to reach the sulphur recovery of 100% from Claus plants, two technology options for the tail gas treating, caustic scrubbing and sulphuric acid production, are discussed and compared. Both of them can be applied to achieve the most stringent requirements and the cost of sulphuric acid production is slightly lower. Be- sides the cost, the factors of overall refinery configuration, crude type and sulphur and nitrogen contents, market demand for selling acid, availability of required utilities, and so on, should also be considered.

  1. Influence of solid loading on D-xylose production through dilute sulphuric acid hydrolysis of olive stones

    Directory of Open Access Journals (Sweden)

    Cuevas, M.

    2015-09-01

    Full Text Available The selective hydrolysis of hemicellulose from olive stones was attempted in order to achieve a maximum D-xylose yield. For this aim, batch hydrolysis was conducted under different operating conditions of temperature, acid concentration and solid loading. Firstly, distilled water, sulphuric acid and nitric acid were assessed as hydrolytic agents at different temperatures (200, 205, 210 and 220 °C and at a fixed acid concentration (0.025 M. Sulphuric acid and 200 °C were selected for the subsequent dilute acid hydrolysis optimization based on the obtained D-xylose yields. The combined influence of solid loading (from 29.3 to 170.7 g olive stones into 300 mL acid solution and sulphuric acid concentration (0.006–0.034 M on the release of D-xylose was then estimated by response surface methodology. According to a statistical analysis, both parameters had significant interaction effects on D-xylose production. The results illustrated that the higher the solid loading, the higher the required acid concentration. The decrease in the solid/liquid ratio in the reactor had a positive effect on D-xylose extraction and on the amount of acid used. The optimum solid loading and sulphuric acid concentration were determined to be 50 g (solid/liquid ratio 1/6 and 0.016 M, respectively. Under these conditions, the predicted D-xylose yield (expressed as g of sugar per 100 g of dry matter fed was 20.4 (87.2% of maximum attainable.Se ha desarrollado una hidrólisis selectiva de la fracción hemicelulósica del hueso de aceituna con el fin de obtener el máximo rendimiento de D-xilosa. Para ello las hidrólisis se llevaron a cabo en un reactor discontinuo a distintas condiciones de temperatura, concentración de ácido y carga de sólidos. En primer lugar se evaluó la capacidad hidrolítica del agua destilada y de los ácidos nítrico y sulfúrico a distintas temperaturas (200, 205, 210 y 220°C manteniendo fija la concentración de ácido (0,025 M. A partir de

  2. New Environment-Friendly Approach for Bastnasite Metallurgic Treatment (I): Extraction of Tetravalent Cerium from Sulphuric Acid Medium with Di(2-ethylhexyl) Phosphoric Acid

    Institute of Scientific and Technical Information of China (English)

    Zhu Zhaowu; Zhao Na; Long Zhiqi; Li Dedong; Cui Dali; Zhang Guocheng

    2005-01-01

    The extraction of cerium(IV) from sulphuric acid medium with Di(2-ethylhexyl) phosphoric acid(DEHPA) was studied. The influence of sulphate ion, acidity, extractant concentration as well as the presence of fluoride ion on the extraction of Ce(IV) was investigated, and the extraction mechanism was also discussed. The results show that sulphate ion can inhibit the extraction of Ce(IV) significantly due to its complexation with Ce(IV). Fluoride ion can enhance Ce(IV) extraction dramatically by the formation of CeF22+ and less amount of CeF3+ which can almost be extracted completely. Nevertheless, in the case as F/Ce(mole ratio) in the initial aqueous phase is approximately more than 1.5, the precipitate will be formed and the extraction can not be progressed smoothly.

  3. Influence of molybdate species on the tartaric acid/sulphuric acid anodic films grown on AA2024 T3 aerospace alloy

    Energy Technology Data Exchange (ETDEWEB)

    Garcia-Rubio, M. [Departamento de Quimica-Fisica Aplicada, Universidad Autonoma de Madrid, 28049 Madrid (Spain); Department of Surface Technologies, Engineering of Materials and Processes, Airbus Spain, Av. John Lennon s/n 28906 Getafe (Spain); Ocon, P. [Departamento de Quimica-Fisica Aplicada, Universidad Autonoma de Madrid, 28049 Madrid (Spain)], E-mail: pilar.ocon@uam.es; Climent-Font, A. [Departamento de Fisica Aplicada, Universidad Autonoma de Madrid (UAM), 28049 Madrid (Spain); Centro de Micro-Analisis de Materiales (CMAM), Universidad Autonoma de Madrid (UAM), 28049 Madrid (Spain); Smith, R.W. [Unidad de Microanalisis de Materiales, Parque Cientifico de Madrid (PCM), Campus de Cantoblanco, 28049 Madrid (Spain); Curioni, M.; Thompson, G.E.; Skeldon, P. [Corrosion and Protection Centre, School of Materials, University of Manchester, M60 1QD England (United Kingdom); Lavia, A.; Garcia, I. [Department of Surface Technologies, Engineering of Materials and Processes, Airbus Spain, Av. John Lennon s/n 28906 Getafe (Spain)

    2009-09-15

    AA2024 T3 alloy specimens have been anodised in tartaric acid/sulphuric media and tartaric acid/sulphuric media containing sodium molybdate; molybdate species were added to the anodising bath to enhance further the protection provided by the porous anodic film developed over the macroscopic alloy surface. Morphological characterisation of the anodic films formed in both electrolytes was undertaken using scanning electron and transmission electron microscopies; the chemical compositions of the films were determined by Rutherford backscattering spectroscopy that was complemented by elemental depth profiling using rf-glow discharge optical emission spectrometry. The electrochemical behaviour was evaluated using potentiodynamic polarisations and electrochemical impedance spectroscopy; the corrosion performance was examined after salt spray testing. The porous anodic film morphology was little influenced by the addition of molybdate salt, although thinner films were generated in its presence. Chemical composition of the anodic film was roughly similar; however, addition of sodium molybdate in the anodizing bath resulted in residues of molybdate species in the porous skeleton and improved corrosion resistance measured by electrochemical techniques that was confirmed by salt spray testing.

  4. Surface enhanced infrared spectroscopy-Au(1 1 1-20 nm)/sulphuric acid - new aspects and challenges

    Energy Technology Data Exchange (ETDEWEB)

    Wandlowski, Th.; Ataka, K.; Pronkin, S.; Diesing, D

    2004-03-30

    The structure and orientation of water molecules on Au(1 1 1-20 nm) film electrodes in contact with aqueous sulphuric acid solution was studied by surface enhanced infrared reflection-absorption spectroscopy (SEIRAS) employing an attenuated total reflection (ATR) configuration (ATR-SEIRAS) with a vertical spectroelectrochemical cell. The spectrum of interfacial water is strongly dependent on electrode potential, ionic strength and pH. Coadsorption of hydronium ions with weakly hydrogen-bonded water molecules was found at EE{sub pzc} strong hydrogen-bonding among water molecules and to coadsorbed sulphate species exists. Based on pH-dependent electrochemical, spectroscopic and in situ STM investigations, a new model is suggested to represent the ordered ({radical}3 x {radical}7) adlayer at maximum sulphate coverage {theta}=0.2: a Zundel or hydrated hydronium ion H{sub 5}O{sub 2}{sup +}, in which one proton is shared between two water molecules, bridges adjacent sulphate species via hydrogen-bonds along the main diagonal of the ({radical}3 x {radical}7) unit cell. This alternating arrangement gives rise to a long-range ordered, 2D network of sulphate and water species interconnected by hydrogen-bonds, and capable to form hydrogen-bonds with second-layer water species. The suggested model is consistent with all experimental observations as well as predictions from quantum-chemical and molecular dynamic simulations.

  5. About safety technology of cleaning tank storing fuming sulphuric acid%发烟硫酸贮罐清洗安全技术

    Institute of Scientific and Technical Information of China (English)

    彭友德

    2001-01-01

    To take the safety measures according to conclusion of analysis accident hidden danger, to clean successfully the tank storing fuming sulphuric acid on neutralization, then to put forward the improving measures.%根据事故隐患分析,采取安全措施,成功地用中和法清洗发烟硫酸贮罐,并提出了贮罐的改进措施。

  6. Alternatieven voor zwavelzuur in chemische luchtwassers = Alternatives for the use of sulphuric acid in air scrubbers

    NARCIS (Netherlands)

    Starmans, D.A.J.; Melse, R.W.

    2011-01-01

    Dit rapport geeft een overzicht van mogelijke zuren die te gebruiken zijn in luchtwassers voor ammoniakverwijdering, inclusief organische zuren, in stallen. Er wordt ingegaan op de veiligheid, de efficiëntie en de kosten van deze zuren.This report provides an overview of the acids that can be used i

  7. Lipid and fatty acid profile of the edible fungus Laetiporus sulphurous. Antifungal and antibacterial properties.

    Science.gov (United States)

    Sinanoglou, Vassilia J; Zoumpoulakis, Panagiotis; Heropoulos, George; Proestos, Charalampos; Ćirić, Ana; Petrovic, Jovana; Glamoclija, Jasmina; Sokovic, Marina

    2015-06-01

    Laetiporus sulphureus is a saprophyte belonging to a specific group of wood-decomposing Basidiomycetes growing on deciduous trees. This fungus has been characterized as a herbal medicine and is also known for its antimicrobial properties. In the present study, high energy extraction techniques using different solvents were compared to obtain maximum yield of the edible fungus Laetiporus sulphureus total lipids. The lipid classes and fatty acid composition of the fruiting bodies' total lipids has been studied using GC-FID and Iatroscan TLC-FID analysis. Among the lipids, the neutral lipids predominated followed by phospholipids and glycolipids. Triglycerides were the most abundant in the neutral lipid fraction, whereas phosphatidylcholine in phospholipids. The existence of relatively high amount of sterols may be correlated to fungus pharmaceutical properties. Total lipids were found to contain high unsaturated degree fatty acids (UFA/SFA>3.4) and dominated of C18:2ω-6, C18:1ω-9 and C16:0 fatty acids. Antibacterial and antifungal properties of mushrooms' lipid extracts from two different solvents were also examined. Results indicated that hexane extracts possessed better antifungal and slightly better antibacterial activity compared to chloroform extracts though both were less active than the commercial antimicrobial agents.

  8. Corrosion Inhibition of Leucaena Leucocephala Pod on Mild Steel in Sulphuric Acid Solution

    Institute of Scientific and Technical Information of China (English)

    P.Muthukrishnan; B.Jeyaprabha; P.Prakash

    2013-01-01

    The corrosion of the mild steel in 1 mol/L H2SO4 was investigated using Leucaena leucocephala pod extract (LLPE) as corrosion inhibitor by weight loss and electrochemical techniques.Inhibition efficiency of 95% was achieved with 500×10-6 of LLPE at 308 K.The polarization studies showed that LLPE acted as mixed type inhibitor.The adsorption of the studied inhibitor on mild steel obeyed Langmuir adsorption isotherm.Protective film formation against acid attack was confirmed by FT-IR,XRD and SEM techniques.

  9. Protein oxidation: an overview of metabolism of sulphur containing amino acid, cysteine.

    Science.gov (United States)

    Ahmad, Saheem; Khan, Hamda; Shahab, Uzma; Rehman, Shahnawaz; Rafi, Zeeshan; Khan, Mohd Yasir; Ansari, Ahsanullah; Siddiqui, Zeba; Ashraf, Jalaluddin Mohammad; Abdullah, Saleh M S; Habib, Safia; Uddin, Moin

    2017-01-01

    The available data suggest that among cellular constituents, proteins are the major target for oxidation primarily because of their quantity and high rate of interactions with ROS. Proteins are susceptible to ROS modifications of amino acid side chains which alter protein structure. Among the amino acids, Cysteine (Cys) is more prone to oxidation by ROS because of its high nucleophilic property. The reactivity of Cys with ROS is due to the presence of thiol group. In the oxidised form, Cys forms disulfide bond, which are primary covalent cross-link found in proteins, and which stabilize the native conformation of a protein. Indirect evidence suggests that thiol modifications by ROS may be involved in neurodegenerative disorders, but the significance and precise extent of the contributions are poorly understood. Here, we review the role of oxidized Cys in different pathological consequences and its biochemistry may increase the research in the discovery of new therapies. The purpose of this review is to re-examine the role and biochemistry of oxidised Cys residues.

  10. Influence of chalcopyrite structure on their leaching by sodium nitrate in sulphuric acid

    Directory of Open Access Journals (Sweden)

    Miroslav Sokić

    2014-03-01

    Full Text Available During the chalcopyrite leaching by sodium nitrate and sulfuric acid solution, leaching rate decreases with increasing the time and a part of chalcopyrite mineral grains remains in the leach residue. In chalcopyrite concentrate, 95.5 % of chalcopyrite mineral occurs as in liberated grains, and the rest is in association with gangue minerals, which is very favorably from the aspect of hydrometallurgical treatment. Complex forms, like impregnations and complex intergrowths, do not exist. After experiments carried out, leaching of copper achieved 84 % at temperature 80 o C and time 240 min. In the all leach residues, 97 % chalcopyrite mineral grains occur as liberated with highly corroded surfaces. Therefore, the structural assembly of chalcopyrite grains is favorable and no reason to reduce the leaching rate in the final stage of reaction. Reason for this is elemental sulfur, which was formed during the reaction, precipitated at the particle surfaces, and slowed down the leaching rate in the final stage of leaching process.

  11. The isotherm slope. A criterion for studying the adsorption mechanism of benzotriazole on copper in sulphuric acid

    Directory of Open Access Journals (Sweden)

    Bastidas, D. M.

    2005-04-01

    Full Text Available The adsorption of benzotriazole (BTA on copper surfaces in 0.001, 0.005 and 0.01 M concentrations of sulphuric acid was investigated using gravimetric measurements. BTA was tested in concentrations from 1x10-5 to 1x10-1 M at temperatures from 298 to 328 K. The adsorption mechanism is discussed in terms of applicability of the conventional Frumkin, Bockris-Swinkels and Kastening-Holleck isotherms, among others. The best fit was obtained using the Frumkin isotherm model. The projected molecular area of BTA was calculated to elucidate inhibitor orientation in the adsorption process

    En el presente trabajo se estudia la adsorción del benzotriazol (BTA sobre el cobre en solución de ácido sulfúrico con concentraciones de 0,001, 0,005 y 0,01 M utilizando medidas gravimétricas. La concentración de BTA ensayada varió de 1x10-5 M a 1x10-1 M y la temperatura de 298 K a 328 K. El mecanismo de adsorción se analiza en términos de la aplicabilidad de las isotermas convencionales de Frumkin, Bockris-Swinkels y Kastening- Holleck, entre otras. La mejor descripción de los resultados se obtuvo utilizando la isoterma de Frumkin. Para analizar la orientación del BTA en el proceso de adsorción sobre el cobre, se calculó la superficie de la molécula de BTA.

  12. Sulphuric Acid Resistant of Self Compacted Geopolymer Concrete Containing Slag and Ceramic Waste

    Directory of Open Access Journals (Sweden)

    Shafiq I.

    2017-01-01

    Full Text Available Malaysia is a one of the developing countries where the constructions of infrastructure is still ongoing, resulting in a high demand for concrete. In order to gain sustainability factors in the innovations for producing concrete, geopolymer concrete containing granulated blast-furnace slag and ceramics was selected as a cement replacement in concrete for this study. Since Malaysia had many ceramic productions and uses, the increment of the ceramic waste will also be high. Thus, a new idea to reuse this waste in construction materials have been tested by doing research on this waste. Furthermore, a previous research stated that Ordinary Portland Cement concrete has a lower durability compared to the geopolymer concrete. Geopolymer binders have been reported as being acid resistant and thus are a promising and alternative binder for sewer pipe manufacture. Lack of study regarding the durability of the geopolymer self-compacting concrete was also one of the problems. The waste will be undergoing a few processes in the laboratory in order to get it in the best form before undergoing the next process as a binder in geopolymer concrete. This research is very significant in order to apply the concept of sustainability in the construction field. In addition, the impact of this geopolymer binder is that it emits up to nine times less CO2 than Portland Cement.

  13. Signatures of Autotrophic and Heterotrophic Metabolic Activity in Enrichment Cultures from a Sulphur Oxidizing Acid Mine Site

    Science.gov (United States)

    Slater, G. F.; Bernier, L.; Cowie, B. R.; Warren, L. A.

    2006-12-01

    Delineating the role of microorganisms in geochemical processes of interest in natural environments requires the development of tools that provide the ability to distinguish amongst microbial activity associated with different metabolic guilds. The gap between phylogenetic characterization and phenotypic understanding remains, underscoring the need to consider alternative methods. Compound specific analysis of cellular components has the potential to differentiate between active metabolic processes supporting microbial communities and may be especially useful in extreme environments. The goal of this study was to determine whether the phospholipids fatty acid (PLFA) distribution and isotopic signatures associated with autotrophs and heterotrophs enriched from an acid mine drainage (AMD) system differed, and further whether natural consortial autotrophic isolates showed similar signatures to autotrophic pure strains of Acidithiobacillus ferrooxidans and A. thiooxidans. Two distinct initial enrichments with tetrathionate and CO2 yielded primarily autotrophic (95%) Acidithiobaccillus spp. sulphur oxidizing communities. The remaining microbial members of theses enrichments (subculture of the consortial isolates in a medium amended with glucose but without tetrathionate selectively resulted in their visible growth. PLFA profiles and δ13C signatures from autotrophic (1) natural enrichments, pure cultures of (2) A. ferrooxidans and (3) A. thiooxidans were similar, but collectively differed from those of the natural heterotrophic enrichment cultures. The PLFA profiles for the heterotrophic communities were made up of primarily (88-99%) C16:0 and two isomers of C18:1. In contrast, the autotrophic communities had high proportions of C16:1 (up to 18%) as well as cyclo C17 and cyclo C19 PLFA that combined comprised 18 to 58% of the observed PLFA. The δ13C signatures of the PLFA also differed strongly between the two trophic levels. The δ13C of the autotrophic PLFA, - 24 to

  14. The recuperation of sulphuric acid out of contaminated solutions by electro electrodialysis; De recuperatie van zwavelzuur uit gecontamineerde oplossingen door elektro elektrodialyse

    Energy Technology Data Exchange (ETDEWEB)

    Cattoir, S.

    1997-05-01

    The dismantling of a nuclear reactor results in large amounts of contaminated waste. The amount of waste is minimized by so-called decontamination processes. These decontamination processes result in decontaminated metal as well as contaminated effluents, containing acid and metal salts. Standard treatment of these effluents involves neutralisation of the acid using sodium hydroxide, resulting in the precipitation of hydroxides; and evaporation of the solvent. However, if the acid is extracted out of the decontamination effluents prior to neutralisation, this acid can be re-used in the decontamination process, substantially reducing the final waste. This report investigates the possibility of using Electro Electrodialysis (EED) for the extraction of 900 moles of sulphuric acid out of a 1 m{sup 3} contaminated solution, containing 22 kg of ferrous, chromous, cerous and nickel ions and 1000 moles of sulphuric acid. EED removes acids out of acid/salts solutions, using an electrolyser equipped with an anionic membrane: the acid-anion is displaced by migration through the membrane while the proton is displaced by electrolysis. This report gives a full description of the technique, the lab-scale apparatus, the analyses involved in studying the technique on lab-scale or monitoring it on full scale, the choice of electrode and membrane and of process parameters such as temperature and current density. On lab scale, EED can displace 90% of the acid out of the acid/salt solution just described, at a current density as high as 0.14 A.cm{sup -2}, at 50 degrees Celsius, if the cathode and the anode are of smoothed platina or of platinised titanium, and the anion selective membrane is the Neosepta AMH -membrane of Tokuyama. The study of EED still needs to be completed with a further study of metal deposition on the cathode, and a comparison of the technique to other (electro)membrane techniques.

  15. Industrial applications of new sulphur biotechnology

    NARCIS (Netherlands)

    Janssen, A.J.H.; Ruitenberg, R.; Buisman, C.J.N.

    2001-01-01

    The emission of sulphur compounds into the environment is undesirable because of their acidifying characteristics. The processing of sulphidic ores, oil refining and sulphuric acid production are major sources of SO2 emissions. Hydrogen sulphide is emitted into the environment as dissolved sulphide

  16. Industrial applications of new sulphur biotechnology

    NARCIS (Netherlands)

    Janssen, A.J.H.; Ruitenberg, R.; Buisman, C.J.N.

    2001-01-01

    The emission of sulphur compounds into the environment is undesirable because of their acidifying characteristics. The processing of sulphidic ores, oil refining and sulphuric acid production are major sources of SO2 emissions. Hydrogen sulphide is emitted into the environment as dissolved sulphide

  17. Connections between atmospheric sulphuric acid and new particle formation during QUEST III–IV campaigns in Heidelberg and Hyytiälä

    Directory of Open Access Journals (Sweden)

    I. Riipinen

    2007-01-01

    Full Text Available This study investigates the connections between atmospheric sulphuric acid and new particle formation during QUEST III and BACCI/QUEST IV campaigns. The campaigns have been conducted in Heidelberg (2004 and Hyytiälä (2005, the first representing a polluted site surrounded by deciduous forest, and the second a rural site in a boreal forest environment. We have studied the role of sulphuric acid in particle formation and growth by determining 1 the power-law dependencies between sulphuric acid ([H2SO4], and particle concentrations (N3–6 or formation rates at 1 nm and 3 nm (J1 and J3; 2 the time delays between [H2SO4] and N3–6 or J3, and the growth rates for 1–3 nm particles; 3 the empirical nucleation coefficients A and K in relations J1=A[H2SO4] and J1=K[H2SO4]2, respectively; 4 theoretical predictions for J1 and J3 for the days when no significant particle formation is observed, based on the observed sulphuric acid concentrations and condensation sinks. In both environments, N3–6 or J3 and [H2SO4] were linked via a power-law relation with exponents typically ranging from 1 to 2. The result suggests that the cluster activation theory and kinetic nucleation have the potential to explain the observed particle formation. However, some differences between the sites existed: The nucleation coefficients were about an order of magnitude greater in Heidelberg than in Hyytiälä conditions. The time lags between J3 and [H2SO4] were consistently lower than the corresponding delays between N3–6 and [H2SO4]. The exponents in the J3∝[H2SO4 ]nJ3-connection were consistently higher than or equal to the exponents in the relation N3–6∝[H2SO4 ]nN36. In the J1 values, no significant differences were found between the observed rates on particle formation event days and the predictions on non-event days. The J3 values predicted by the cluster activation or kinetic nucleation hypotheses, on the other hand, were considerably lower on non-event days

  18. VOC measurements within a boreal forest during spring 2005: the role of monoterpenes and sulphuric acid in selected intense nucleation events

    Directory of Open Access Journals (Sweden)

    G. Eerdekens

    2009-06-01

    Full Text Available In this study we present measurements of selected trace gases and aerosol made in a boreal forest during the BACCI-QUEST IV intensive field campaign in Hyytiälä, Finland in April 2005. Several clear aerosol "nucleation events" were observed and characterized. One type of "event" occurred synchronously with huge increases in monoterpenes, while a second event type correlated instead with sulphuric acid. Here we elucidate the origin of these two distinct forms of aerosol production at the Hyytiälä site using the measurement data, airmass back trajectories and the optical stereoisomery of monoterpenes.

  19. The use of ion-selective membranes for the recovery of sulphuric acid out of contaminated solutions. Comparing electrodialysis, electro electrodialysis and diffusion dialysis

    Energy Technology Data Exchange (ETDEWEB)

    Cattoir, S.

    1998-02-01

    The amount of waste arising from dismantled reactors is minimized by decontamination processes. These processes result in contaminated effluents, containing acid and metal salts. The quantity of final waste can be substantially reduced when the acid is extracted out of the decontamination effluents prior to neutralisation. This report discusses three membrane techniques for the displacement of acids out of mixed acid/salt solutions: electrodialysis (ED), electro electrodialysis (EED) and diffusion dialysis (DD). EED uses an electrical potential difference across an anion-selective membrane; DD uses a concentration difference across an anion-selective membrane; ED uses an electrical potential difference, across an anion- and a cation-selective membrane. EED can displace up to 90% of the sulphuric acid, the amount of metal ions in the displaced-acid solution is less than 1% of the ions in the original contaminated solution. Treatment costs are estimated to about 18 Belgian Francs per litre. In DD the purity of the displaced acid is comparable to EED. Treatment costs are about 21 Belgian Francs per litre. In ED 90% acid-displacement is easily reached, but 5% metal ions are also displaced. Treatment costs are about 6 Belgian Francs per litre. Therefore, in spite of the lower purity of the resulting acid, ED is economically speaking the best choice.

  20. SMED - Sulphur MEditerranean Dispersion

    Science.gov (United States)

    Salerno, Giuseppe G.; Sellitto, Pasquale; Corradini, Stefano; Di Sarra, Alcide Giorgio; Merucci, Luca; Caltabiano, Tommaso; La Spina, Alessandro

    2016-04-01

    Emissions of volcanic gases and particles can have profound impacts on terrestrial environment, atmospheric composition, climate forcing, and then on human health at various temporal and spatial scales. Volcanic emissions have been identified as one of the largest sources of uncertainty in our understanding of recent climate change trends. In particular, a primary role is acted by sulphur dioxide emission due to its conversion to volcanic sulphate aerosol via atmospheric oxidation. Aerosols may play a key role in the radiative budget and then in photochemistry and tropospheric composition. Mt. Etna is one of the most prodigious and persistent emitters of gasses and particles on Earth, accounting for about 10% of global average volcanic emission of CO2 and SO2. Its sulphur emissions stand for 0.7 × 106 t S/yr9 and then about 10 times bigger than anthropogenic sulphur emissions in the Mediterranean area. Centrepiece of the SMED project is to advance the understanding of volcanogenic sulphur dioxide and sulphate aerosol particles dispersion and radiative impact on the downwind Mediterranean region by an integrated approach between ground- and space-based observations and modelling. Research is addressed by exploring the potential relationship between proximal SO2 flux and aerosol measured remotely in the volcanic plume of Mt. Etna between 2000 and 2014 and distal aerosol ground-based measurements in Lampedusa, Greece, and Malta from AERONET network. Ground data are combined with satellite multispectral polar and geostationary imagers able to detect and retrieve volcanic ash and SO2. The high repetition time of SEVIRI (15 minutes) will ensure the potential opportunity to follow the entire evolution of the volcanic cloud, while, the higher spatial resolution of MODIS (1x1 km2), are exploited for investigating the probability to retrieve volcanic SO2 abundances from passive degassing. Ground and space observations are complemented with atmospheric Lagrangian model

  1. Sulphur is your business

    Energy Technology Data Exchange (ETDEWEB)

    Hyne, J.B. [Hyjay RandD Ltd (Canada)

    2011-07-01

    J.B. Hyne describes the evolution of the sulphur industry, and the hidden potential companies have yet to tap into. Sulphur was at first expelled as a pollutant (SO2) but now it is mined and extracted. Much research has been completed on the uses of sulphur, including its use in the enhancement of the material properties of asphalts and concretes. The full potential of sulphur is not always realized and there is a lack of investment interest, financial motivation, and market diversification. There are many creative ideas for the use of sulphur, including its use as a component in N,P,K fertilizers, and as a component in solar energy collectors. The latter use of sulphur derives from thiophenic sulphur extracted from oil sand bitumen (5-7% sulphur), and which is semi-conducting. Untapped opportunities for sulphur include brake fluids, sulphur concrete, elevated temperature fluids, photovoltaics and carbon and sulphur, among others. At present the missing link is for market opportunities to be opened up and explored.

  2. Sulphur condensation influence in Claus catalyst performance.

    Science.gov (United States)

    Mora, R L

    2000-12-01

    The Claus process is an efficient way of removing H(2)S from acid gas streams and this is widely practised in industries such as natural gas processing, oil refining and metal smelting. Increasingly strict pollution control regulations require maximum sulphur recovery from the Claus unit in order to minimise sulphur-containing effluent. The most widely used Claus catalyst in sulphur recovery units is non-promoted spherical activated alumina. Properties associated with optimum non-promoted Claus catalyst performance include high surface area, appropriate pore size distribution and enhanced physical properties. The objective of this paper is to outline a procedure in order to estimate Claus catalyst effectiveness after pore plugging due to sulphur condensation. Catalyst deactivation due to pore plugging by sulphur is modelled employing a Bethe lattice and its corresponding performance is described by means of a modified effectiveness factor. Model results show an improvement in the modified effectiveness factor due to modifications in catalyst porous structure.

  3. Aircraft induced sulphur impact on the atmosphere

    Science.gov (United States)

    Dessens, O.; Rogers, H. L.; Pyle, J. A.

    2009-12-01

    Sulphur is present in aviation fuel and as consequence SO2 is emitted by aviation in the atmosphere. SO2 is then rapidly oxidised in H2SO4 that can produce sulphuric acid aerosol. The impact of the sulphuric acid aerosol on the atmospheric chemistry has been studied in two different region of the atmosphere: the upper troposphere lower stratosphere (UTLS) and the surface. The first part of the study will focus on the impact of sulphur emissions from aircraft at cruise altitude within the UTLS. The results presented have been obtained with the stratospheric chemistry transport model (CTM) SLIMCAT. For that study a full microphysical module for stratospheric sulphuric aerosol (SAMM) has been included within the CTM. The impact on the ozone concentration in the UTLS is calculated for the present day subsonic fleet emissions. The sulphuric acid aerosol surface density due to aviation reach 1.8μm2/cm3 and the ozone change calculated is -0.22ppbv at the mid-latitudes Northern Hemisphere at 12 km altitude (ozone change due to NOx emissions at the same location: +4.5ppbv). These results are compared to results from other models calculated during the QUANTIFY project. The second part of the study is looking at the impact of the sulphur emitted by aviation below 3kFeet. These calculations have been performed with the tropospheric CTM pTOMCAT. For that purpose a standard tropospheric sulphur cycle as well as a tropospheric microphysic parametrisation of sulphuric acid aerosol have been introduced within pTOMCAT. Two different fuel are used under 3kFeet in the simulations: one normal kerosene and one ultra-low-sulphur (ULS) kerosene. The reduction in sulphuric acid aerosol surface density using the ULS fuel is only reaching -2 to -5% compare to the background surface level (sulphur emissions from other anthropic and biogenic sources are higher than aviation). The impact of the ULS fuel use on the ozone concentration within the planetary boundary layer is relatively weak and

  4. Copper—Induced Changes in the Urea Uptake and Urease Activity in the Cyanobacteria Anabaena doliolum and Anacystis Nidulans:Interaction With Sulphur Containing Amino Acids

    Institute of Scientific and Technical Information of China (English)

    S.SINGH; B.B.SINGH; 等

    1995-01-01

    Copper-induced changes in the urea uptake and urease activity have been investigated in the cyanobacteria Anabaena doliolum and Anacystis nidulans.Copper,at and above 5μmol/L concentration,inhibited urea uptake and urease activity systems in both the cyanobacteria in a concentration dependent manner,However,the urea uptake and urease activity systems in A.nidulans apeared slightly more tolerant to copper than that of A.doliolum.The inhibitory effect of copeer on urea uptake and urease activity was mitigated by sulphur containing amino acids(cystine and cysteine),however,methionine could not do so,indicating the involvement of sulfhydryl(-SH) groups in the assimilation of urea in cyanobacteria.

  5. Sulphur Extraction at Bryan Mound

    Energy Technology Data Exchange (ETDEWEB)

    Kirby, Carolyn L [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Lord, Anna C. Snider [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-08-01

    The Bryan Mound caprock was subjected to extens ive sulphur mining prior to the development of the Strategic Petroleum Reserve. Undoubtedl y, the mining has modified the caprock integrity. Cavern wells at Bryan Mound have been subject to a host of well integr ity concerns with many likely compromised by the cavernous capro ck, surrounding corrosive environment (H 2 SO 4 ), and associated elevated residual temperatures al l of which are a product of the mining activities. The intent of this study was to understand the sulphur mining process and how the mining has affected the stability of the caprock and how the compromised caprock has influenced the integrity of the cavern wells. After an extensiv e search to collect pert inent information through state agencies, literature sear ches, and the Sandia SPR librar y, a better understanding of the caprock can be inferred from the knowledge gaine d. Specifically, the discovery of the original ore reserve map goes a long way towards modeling caprock stability. In addition the gained knowledge of sulphur mining - subs idence, superheated corrosive wa ters, and caprock collapse - helps to better predict the post mi ning effects on wellbore integrity. This page intentionally left blank

  6. The role of phosphate additive in stabilization of sulphuric-acid-based vanadium(V) electrolyte for all-vanadium redox-flow batteries

    Science.gov (United States)

    Roznyatovskaya, Nataliya V.; Roznyatovsky, Vitaly A.; Höhne, Carl-Christoph; Fühl, Matthias; Gerber, Tobias; Küttinger, Michael; Noack, Jens; Fischer, Peter; Pinkwart, Karsten; Tübke, Jens

    2017-09-01

    Catholyte in all-vanadium redox-flow battery (VRFB) which consists of vanadium salts dissolved in sulphuric acid is known to be stabilized by phosphoric acid to slow down the thermal aging at temperatures higher than 40 °C. To reveal the role of phosphoric acid, the thermally-induced aggregation is investigated using variable-temperature 51V, 31P, 17O, 1H nuclear magnetic resonance (NMR) spectroscopy and dynamic light scattering (DLS). The results indicate that the thermal stabilization of vanadium(V) electrolyte is attained by the involvement of monomeric and dimeric vanadium(V) species in the reaction with phosphoric acid which is concurrent to the formation of neutral hydroxo-aqua vanadium(V) precipitation precursor. The dimers are stabilized by counter ions due to association reaction or if such stabilization is not possible, precipitation of vanadium pentoxide is favored. The evolution of particles size distributions at 50 °C in electrolyte samples containing 1.6 M vanadium and 4.0 M total sulphate and the pathways of precipitate formation are discussed. The optimal total phosphate concentration is found to be of 0.15 M. However, the induction time is assumed to be dependent not only on the total phosphate concentrations, but also on the ratio of total vanadium(V) to sulphate concentrations.

  7. Effectiveness of Higher Fatty Acids C8, C10 and C12, Dimethyl Dicarbonate and Sulphur Dioxide for Inhibition of Re-fermentation and Malolactic Activities in Wine

    Directory of Open Access Journals (Sweden)

    Mojmír Baroň

    2014-01-01

    Full Text Available The issue of preventing the re-fermentation and protection against undesirable malolactic fermentation (MLF in order to safe content of acids in wine is very complicated. In this paper the saturated higher fatty acids (HFA – C8, C10 and C12, dimethyldicarbonate (DMDC and sulphur dioxide (SO2 were tested. The re-fermentation test showed the strongest inhibition power at ratio 2:8, 1:9 and 0:10 as C8:C10 acids – 65 days without re-fermentation. MLF experiments confirmed that addition of SO2 into the fermenting media causes rapid inhibition of lactic acid bacteria metabolic activity. Malic acid concentrations were proportionally decreasing during 6 days of experiment and at the end the content of this acid varied between 0.16 and 0.22 g/L, the only exception formed a variant with the addition of SO2 (1.57 g/L of malic acid. After calculation of the average consumption rate of malic acid, the results showed the inhibition power – SO2 (81.05% followed by variant of 40 mg/L mixture of HFA (40.76%, a variant of 200 mg/L of DMDC (31.98% and a variant of 20 mg/L mixture of HFA (12.59%. The addition of HFA can significantly reduce the dosage of other preservatives, especially SO2. Based on results, this method can be recommend in the production of wines with residual sugar and also wines made from over-mature material to prevent undesirable MLF.

  8. Corrosion inhibition of 6061 Al-15 vol. pct. SiC(p) composite and its base alloy in a mixture of sulphuric acid and hydrochloric acid by 4-(N,N-dimethyl amino) benzaldehyde thiosemicarbazone

    Energy Technology Data Exchange (ETDEWEB)

    Pinto, Geetha Mable [Department of Chemistry, National Institute of Technology Karnataka, Surathkal, Srinivasnagar 575 025, Mangalore, Karnataka (India); Nayak, Jagannath [Department of Metallurgical and Materials Engineering, National Institute of Technology Karnataka, Surathkal, Srinivasnagar 575 025, Karnataka (India); Shetty, A. Nityananda, E-mail: nityashreya@gmail.com [Department of Chemistry, National Institute of Technology Karnataka, Surathkal, Srinivasnagar 575 025, Mangalore, Karnataka (India)

    2011-02-15

    Research highlights: {yields} Corrosion inhibition of Al-SiC composite. {yields} DMABT as corrosion inhibitor. {yields} Inhibition through physisorption of DMABT. - Abstract: The corrosion inhibition characteristics of 4-(N,N-dimethylamino) benzaldehyde thiosemicarbazone (DMABT) on the corrosion behavior of 6061 Al-15 vol. pct. SiC(p) composite and its base alloy were studied at different temperatures in acid mixture medium containing varying concentrations of hydrochloric acid and sulphuric acid using Tafel extrapolation technique and ac impedance spectroscopy (EIS). The effect of inhibitor concentration, temperature and concentration of the acid mixture media on the inhibitor action was investigated. It was found that inhibition efficiencies increase with the increase in inhibitor concentration, but decrease with the increase in temperature and with the increase in concentration of the acid media. Thermodynamic parameters for dissolution process were determined. The adsorption of DMABT on both the composite and base alloy was found to be through physisorption obeying Freundlich adsorption isotherm.

  9. Studies on the microbial sulphur cycle in acid ponds in the Niederlausitz mining region in Brandenburg; Untersuchungen zum mikrobiellen Schwefelkreislauf in sauren Tagebau-Restseen der Niederlausitz (Brandenburg)

    Energy Technology Data Exchange (ETDEWEB)

    Meier, J.

    2001-07-01

    The water quality of the acid ponds in the Niederlausitz brown coal mining region is characterised by pH values below 3 and high concentrations of dissolved iron (up to 10 mM) and sulphate (up to 30 mM). The development of these ponds is determined by the equilibrium that arises between acidifying and alkalinising processes. Acidity develops through weathering and oxidation of iron sulphides in the mining refuse, whereas alkalinity arises through the reduction of iron (III) and sulphate in the pond sediments, a process associated with the oxidation of organic matter. The purpose of the present study was to examine the influence of sulphate reduction and sulphur oxidation on the neutralising potential of the sediments in acid ponds and to characterise and identify the microorganisms involved in these processes. Comparative explorations were performed in two acid waters, namely ponds 111 and 107, and in a neutral water, namely pond B, in a semi-natural area of the Niederlausitz region. [German] Die Wasserqualitaet der sauren Bergbau-Restseen im Braunkohlerevier der Niederlausitz ist durch pH-Werte unter pH 3 und hohe Konzentrationen an geloestem Eisen (bis zu 10 mM) und Sulfat (bis zu 30 mM) gekennzeichnet. Die Entwicklung der Restseen wird durch das Gleichgewicht von aziditaets- und alkalinitaetsbildenden Prozessen bestimmt. Aziditaet entsteht bei der Verwitterung bzw. der Oxidation der Eisensulfide im Kippmassiv, waehrend Alkalinitaet bei der an die Oxidation organischer Substanz gekoppelte Reduktion von Eisen(III) und Sulfat in den Sedimenten der Seen gebildet wird. In der vorliegenden Arbeit wurde der Einfluss der Sulfratreduktion und der Schwefeloxidation auf das Neutralisierungspotenzial der Sedimente der sauren Restseen untersucht sowie die an diesen Prozessen beteiligten Mikroorganismen charakterisiert und identifiziert. Vergleichende Untersuchungen wurden in zwei sauren, Restsee 111 und 107, und in einem neutralen Gewaesser, Restsee B, im naturnahen Bereich

  10. Siro(haem)amide in Allochromatium vinosum and relevance of DsrL and DsrN, a homolog of cobyrinic acid a,c-diamide synthase, for sulphur oxidation.

    Science.gov (United States)

    Lübbe, Yvonne J; Youn, Hyung-Sun; Timkovich, Russell; Dahl, Christiane

    2006-08-01

    In the purple sulphur bacterium Allochromatium vinosum, the prosthetic group of dissimilatory sulphite reductase (DsrAB) was identified as siroamide, an amidated form of the classical sirohaem. The genes dsrAB are the first two of a large cluster of genes necessary for the oxidation of sulphur globules stored intracellularly during growth on sulphide and thiosulphate. DsrN is homologous to cobyrinic acid a,c diamide synthase and may therefore catalyze glutamine-dependent amidation of sirohaem. Indeed, an A. vinosumDeltadsrN in frame deletion mutant showed a significantly reduced sulphur oxidation rate that was fully restored upon complementation with dsrN in trans. Sulphite reductase was still present in the DeltadsrN mutant. DsrL is a homolog of the small subunits of bacterial glutamate synthases and was proposed to deliver glutamine for sirohaem amidation. However, recombinant DsrL does not exhibit glutamate synthase activity nor does the gene complement a glutamate synthase-deficient Escherichia coli strain. Deletion of dsrL showed that the encoded protein is absolutely essential for sulphur oxidation in A. vinosum.

  11. Effects of sulphuric acid and acidifying ammonium deposition on water quality and vegetation of simulated soft water ecosystem

    Energy Technology Data Exchange (ETDEWEB)

    Schuurkes, J.A.A.R.; Heck, I.C.C; Hesen, P.L.G.M.; Leuven, R.S.E.W.; Roelofs, J.G.M.

    1986-11-01

    In a greenhouse, seven identical mini-ecosystems, simulating soft water ponds, were exposed to different types of artificial rain water. The effects of rain water containing H/sub 2/SO/sub 4/ and nitrate, and rain water containing ammonium sulphate on water quality and vegetation were studied and compared. Causal relations were established between rain water quality, water chemistry and changes in floristic composition. Ammonium sulphate deposition, particularly, strongly affected water quality and vegetation development. Although ammonium sulphate deposition was only slightly acid, due to nitrification it acted as an important acid source, causing acidification to pH 3.8. Under acidified conditions, ammonium sulphate deposition led to a luxuriant growth of Juncus bulbosus and Agrostis canina. In the mini-ecosystems, H/sub 2/SO/sub 4/ deposition with a pH of 3.5 only decreased the pH of the water to 5.1 within 1 yr, the acidification of water appeared to be coupled with changes in alkalinity, sulphate, Al, Cd, Ca, Mg, K and inorganic-N. It is concluded that in NH/sub 3/-affected regions in The Netherlands, the high atmospheric deposition of ammonium sulphate probably contributes to a large extent in the acidification, eutrophication and floristic changes of oligotrophic soft waters. 10 references.

  12. Hydrometallurgical route to recover molybdenum, nickel, cobalt and aluminum from spent hydrotreating catalysts in sulphuric acid medium.

    Science.gov (United States)

    Valverde, Ivam Macedo; Paulino, Jéssica Frontino; Afonso, Julio Carlos

    2008-12-30

    This work describes a hydrometallurgical route for processing spent commercial catalysts (CoMo and NiMo/Al2O3), for recovering the active phase and support components. They were initially pre-oxidized (500 degrees C, 5h) in order to eliminate coke and other volatile species present. Pre-oxidized catalysts were dissolved in H2SO4 (9molL-1) at approximately 90 degrees C, and the remaining residues separated from the solution. Molybdenum was recovered by solvent extraction using tertiary amines. Alamine 304 presented the best performance at pH around 1.8. After this step, cobalt (or nickel) was separated by adding aqueous ammonium oxalate in the above pH. Before aluminum recovery, by adding NaOH to the acid solution, phosphorus (H2PO4-) was removed by passing the liquid through a strong anion exchange column. Final wastes occur as neutral and colorless sodium sulphate solutions and the insoluble solid in the acid leachant. The hydrometallurgical route presented in this work generates less final aqueous wastes, as it is not necessary to use alkaline medium during the metal recovery steps. The metals were isolated in very high yields (>98wt.%).

  13. Impact of sulphur fumigation on the chemistry of ginger.

    Science.gov (United States)

    Wu, Cheng-Ying; Kong, Ming; Zhang, Wei; Long, Fang; Zhou, Jing; Zhou, Shan-Shan; Xu, Jin-Di; Xu, Jun; Li, Song-Lin

    2018-01-15

    Ginger (Zingiberis Rhizoma), a commonly-consumed food supplement, is often sulphur-fumigated during post-harvest handling, but it remains unknown if sulphur fumigation induces chemical transformations in ginger. In this study, the effects of sulphur fumigation on ginger chemicals were investigated by ultra-high performance liquid chromatography coupled with quadrupole time-of-flight mass spectrometry (UHPLC-QTOF-MS/MS)-based metabolomics. The results showed that sulphur fumigation significantly altered the holistic chemical profile of ginger by triggering chemical transformations of certain original components. 6-Gingesulphonic acid, previously reported as a naturally-occurring component in ginger, was revealed to be a sulphur fumigation-induced artificial derivative, which was deduced to be generated by electrophilic addition of 6-shogaol to sulphurous acid. Using UHPLC-QTOF-MS/MS extracting ion analysis with 6-gingesulphonic acid as a characteristic chemical marker, all the commercial ginger samples inspected were determined to be sulphur-fumigated. The research outcomes provide a chemical basis for further comprehensive safety and efficacy evaluations of sulphur-fumigated ginger. Copyright © 2017 Elsevier Ltd. All rights reserved.

  14. Sulphur recirculation for reduced boiler corrosion; Minskad pannkorrosion med svavelrecirkulation

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Sven; Karlsson, Martin (Goetaverken Miljoe AB, Goeteborg (Sweden)); Blomqvist, Evalena; Baefver, Linda; Claesson, Frida; Davidsson, Kent (SP Sveriges Tekniska Forskningsinstitut, Boraas (Sweden)); Froitzheim, Jan; Pettersson, Jesper; Steenari, Britt-Marie (Chalmers Tekniska Hoegskola, Oorganisk miljoekemi, Goeteborg (Sweden))

    2010-03-15

    Sulphur recirculation is a new technology for reducing boiler corrosion and dioxin formation, which was demonstrated in full-scale tests performed at the Renova Waste to Energy plant at Saevenaes in Goeteborg (Sweden). Sulphur is recirculated from the flue gas cleaning back to the boiler, which reduces the chloride content of the deposits, which in turn reduces boiler corrosion and dioxin formation. Sulphur dioxide was separated from the flue gas in a wet scrubber by adding hydrogen peroxide, producing sulphuric acid. The sulphuric acid was injected into the furnace using nozzles with atomization air, surrounded by recirculated flue gas for improved mixing. By recirculating the sulphur, the sulphur dioxide concentration was increased in the boiler. Each sulphur atom passed the boiler several times and no external sulphur had to be added. Dioxin, ash, deposits and particle samplings together with 1000 h corrosion probe measurements were performed for normal operation (reference) and with sulphur recirculation respectively. During spring 2009, reference measurements were made and the recirculation system was installed and tested. During autumn 2009, a long term test with sulphur recirculation was made. An SO{sub 2} concentration of approximately 800 mg/m3 (n, d.g.) was maintained in the boiler by the system except during a period of extremely low sulphur content in the waste. The sulphur dioxide stack concentrations have been far below the emission limit. Sulphuric acid dew point measurements have shown that the sulphuric acid dosage did not lead to elevated SO{sub 3} concentrations, which may otherwise lead to low temperature corrosion. The chlorine content of both fly ash and boiler ash decreased and the sulphur content increased during the sulphur recirculation tests. The molar chlorine/sulphur ratio (Cl/S) decreased by two thirds in the fly ash as well as in the boiler ash, except for one sample. With sulphur recirculation in operation, the deposit growth was

  15. Anodically generated manganese(III) sulphate for the oxidation of dipeptides in aqueous sulphuric acid medium: A kinetic study

    Indian Academy of Sciences (India)

    M N Kumara; D Channe Gowda; A Thimme Gowda; K S Rangappa

    2004-01-01

    The kinetic of oxidation of dipeptides (DP) namely valyl-glycine (Val-Gly), alanyl-glycine (Ala-Gly) and glycyl-glycine (Gly-Gly), by Mn(III) have been studied in the presence of sulphate ions in acid medium at 26°C. The reaction was followed spectrophotometrically at max = 500 nm. A firstorder dependence of the rate on both [Mn(III)]$_o$ and [DP]o was observed. The rate is independent of the concentration of reduction product, Mn(II) and hydrogen ions. The effects of varying the dielectric constant of the medium and addition of anions such as sulphate, chloride and perchlorate were studied. The activation parameters have been evaluated using Arrhenius and Eyring plots. The oxidation products were isolated and characterized. A mechanism involving the reaction of DP with Mn(III) in the ratelimiting step is suggested. An apparent correlation was noted between the rate of oxidation and the hydrophobicity of these dimers, where increased hyphobicity results in increased rate of oxidation.

  16. Modeling of solvent extraction equilibrium of Cu(II from sulphuric Acid solution with MOC-55TD

    Directory of Open Access Journals (Sweden)

    Alguacil, F. J.

    1999-06-01

    Full Text Available The extraction of Cu(II from acidic sulphate aqueous solutions using the commercial MOC-55TD extractant is studied. A predictive model, which consists in a set of non-linear mass action and mass balance equations is proposed. The model was solved using a tailor-made equation-solving program. The extraction of copper can be described by the formation of CuR2 species (log Kext= 0.717 ± 0.03 in the organic phase. The copper equilibrium isotherm was also obtained at 20°C.

    Se estudia la extracción de Cu(II de disoluciones acuosas acidas, en medio sulfato, mediante la oxima comercial MOC-55TD. Se propone un modelo para predecir la extracción del metal; este modelo consiste en una serie de ecuaciones no lineales de acción de masas y balance de masas. El modelo se resolvió empleando un programa de ordenador específicamente definido para este tipo de equilibrios. La extracción de cobre se describe por la formación de la especie CuR2 (log Kext= 0,717 ± 0,03 en la fase orgánica. Se ha obtenido la isoterma de extracción de cobre a 20 °C.

  17. Estudios Cinéticos de la Disolución de Hidroboracita en Soluciones de Acido Clorhídrico y Acido Sulfúrico Dissolution Kinetics of Hydroboracite in Hydrochloric Acid and Sulphuric Acid Solutions

    Directory of Open Access Journals (Sweden)

    Graciela V Morales

    2008-01-01

    Full Text Available Se realizan estudios cinéticos de la disolución de hidroboracita en soluciones de ácido clorhídrico y ácido sulfúrico en un reactor tanque agitado discontinuo de acero inoxidable, a presión atmosférica. Se investiga el efecto de la temperatura, el tamaño de partícula, la relación sólido/líquido y la concentración de ácido sobre la velocidad de disolución. Los resultados experimentales permiten observar que la velocidad de disolución aumenta con el incremento de la concentración del ácido y de la temperatura, y disminuye con el aumento del tamaño de partícula y con la relación sólido/líquido. La energía de activación aparente calculada para la disolución de hidroboracita en soluciones de ácido clorhídrico es 44.9 kJ/mol, lo cual no permite inferir cual es la etapa controlante del proceso; mientras que la energía de activación aparente calculada para la disolución de hidroboracita en soluciones de ácido sulfúrico es 14.6 kJ/mol, lo cual permite inferir que el proceso ocurre con control difusivo.The dissolution kinetics of hydroboracite in hydrochloric acid and sulphuric acid solutions was investigated. The experiments were carried out in a steel batch reactor equipped with a mechanical stirrer, at atmospheric pressure. The effect of reaction temperature, particle size, solid/liquid ratio and acid concentration on the dissolution rate was determined. It was found that the dissolution rate increased with increasing the acid concentration and reaction temperature. However, the increase of particle size and solid/liquid ratio decreased the dissolution rate. The activation energy for the hydroboracite dissolution in hydrochloric acid was calculated as 44.9 kJ/mol, which does not permit to know the process controlling step. The activation energy for the hydroboracite dissolution in sulphuric acid was found to be 14.6 kJ/mol, which indicates that the dissolution is a diffusion controlled process.

  18. Sulphur oxidising bacteria in mangrove ecosystem: A review

    African Journals Online (AJOL)

    SAM

    2014-07-16

    Jul 16, 2014 ... short chain fatty acids, carbon dioxide and hydrogen ion. (Das et al., 2012). ... If an abundant supply of carbon is .... to generate energy from oxidation of reduced sulphur ..... Worldwide deposition of waste rubber materials, for.

  19. THE SOLUBILITY OF MILAS BAUXITE ORE IN SULPHURIC ACI

    Directory of Open Access Journals (Sweden)

    Mustafa GULFEN

    2001-06-01

    Full Text Available The effects of calcination conditions,sulphuric acid concentrations and dissolvingtemperature and period as parameters to thesolubility of the bauxite ore from Gobekdagı reservesin Mugla-Milas region were investigated. The bauxitesamples were calcined in different periods at differenttemperatures. Then the solubility of the calcinedbauxite samples in sulphuric acid solution wasexamined. Dissolving activation energy (Ea wascalculated using the optimum kinetics equation andthe results obtained from the solubility studiesexamined dissolving temperatures and periods

  20. Effects of adding sulphuric acid on composting process of cattle manure and changes of main nutrients%添加硫酸对牛粪堆肥过程及其养分变化的影响

    Institute of Scientific and Technical Information of China (English)

    胡雨彤; 时连辉; 刘登民; 仝少伟; 魏美艳; 孙杰

    2014-01-01

    为研究不同浓度硫酸对畜禽粪便条垛式堆肥中pH值以及养分含量动态变化的影响,以牛粪和锯末为试验材料,以实验室常用浓硫酸稀释成不同浓度为添加物,在露天进行43 d的条垛式堆肥,测定堆肥过程中温度、水分、pH值、全量和速效养分含量,并以种子发芽指数测定堆肥效果。结果表明,在初始物料中添加0.2 mol/L、0.3 mol/L的硫酸对缩短堆肥高温上升期,降低堆肥pH和促进有机质分解,提高堆肥中全氮、全磷、全钾、有效磷、速效钾含量具有明显效果。其中添加0.2 mol/L硫酸堆体在堆肥43天时全氮、全钾、全磷、速效钾、有效磷与堆肥对照相比分别增加了19.51%、13.49%、6.07%、21.39%、9.03%。堆肥结束时各个处理发芽指数均达到80%以上,不会对植物造成毒害作用。整体来说,牛粪堆肥中添加0.2 mol/L的硫酸,堆肥效果最好。本研究为硫酸添加物应用于实际堆肥工程提供了理论依据。%In this study , to explore the effects of different concentrations of sulphuric acid on changes of pH and main nutrient elements during the windrow compost , an experiment of cattle manure composting was carried out for 43 days.Besides the control , three mixtures were treated with addition of different concentrations of sulphuric acid , 0.1 mol/L, 0.2 mol/L and 0.3 mol/L.The results show that during 43 days, the sulphuric acid addition treatments at 0.2 mol/L and 0.3 mol/L decrease the stage of initial high temperature , pH and carbon losses significantly, and increase the contents of total N , total K, total P, available potassium and available phosphorus effectively.The total N, total K, total P, available potassium and available phosphorus in the 0.2 mol/L sulphuric acid compost are increased by 19.51%, 13.49%, 6.07%, 21.39% and 9.03% respectively compared to the control in the 43 days.The germination index ( GI) value is over 80%at the

  1. X-ray photoelectron spectroscopy of oxygen-containing layers formed by a linear potential scan on stepped gold (111) films in aqueous 1 M sulphuric acid

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez Nieto, Felipe J. [Instituto de Investigaciones Fisicoquimica Teoricas y Aplicadas INIFTA, Universidad Nacional de La Plata, Consejo Nacional de Investigaciones Cientificas y Tecnicas Sucursal 4, Casilla de Correo 16, (1900) La Plata (Argentina); Member of Comision de Investigaciones Cientificas de la Provincia de Buenos Aires (Argentina)], E-mail: rodrini@inifta.unlp.edu.ar; Fachini, Esteban; Cabrera, Carlos R. [Department of Chemistry, University of Puerto Rico, Rio Piedras Campus, P.O. Box 23346, San Juan, 00931-3346 (Puerto Rico); Arvia, Alejandro J. [Instituto de Investigaciones Fisicoquimica Teoricas y Aplicadas INIFTA, Universidad Nacional de La Plata, Consejo Nacional de Investigaciones Cientificas y Tecnicas Sucursal 4, Casilla de Correo 16, (1900) La Plata (Argentina)

    2009-01-01

    X-ray photoelectron spectroscopy (XPS) data of oxygen-containing layers (O-layers) made on stepped gold (111) film electrodes from aqueous 1 M sulphuric acid by single linear potential scans at 0.10 V s{sup -1} and 298 K are reported. The potential scan covered from the open circuit potential to anodic switching potential E{sub as} = 2.50 V versus normal hydrogen electrode (NHE) and holding times at E{sub as} in the range 30-300 s. The anodic charge density q{sub a} determined from the oxidation and reduction voltammetric scan is in the range 0.20 {<=} q{sub a} {<=} 2.5 mC cm{sup -2}. For the potential E = 0.5 V, in the absence of O-layers, the S 2p core level spectrum indicates the presence of sulphate/bisulphate adsorbates. For E{sub as} > 1.3 V, the O 1s core level spectrum involves the contribution from water, OH- and O-species. These spectra are deconvoluted utilising either three or four Gaussian contributions with values of peaked binding energy and full width at half-maximum height (FWMH) in good agreement with expectations. The envelope of these XPS O 1s signals after correction for the contribution of sulphate/bisulphate adsorbates and adventitious carbon approaches the XPS signal that has been reported for the core level spectrum in the O 1s region of oxidised gold surfaces produced by laser pulses at different molecular oxygen pressures. The O/OH concentration ratio in the O-layer increases with E{sub as} ageing time t{sub ag} and cathodic charge density q{sub c}. The hydrous nature of the O-layer, evaluated through the analysis of the core level spectra in the O 1s region, decreases as E{sub as} and t{sub ag} are increased. Results are interesting to unravel the composition and structure of electrochemically grown O-layers at the surface of the gold substrate, and the influence of the history of these O-layers on the respective XPS features.

  2. Application of balanced flow meter in sulphuric acid plant%多孔平衡流量计在硫酸装置中的应用

    Institute of Scientific and Technical Information of China (English)

    王健

    2011-01-01

    介绍了多孔平衡流量计结构、特点和工作原理。与传统差压式流量计相比,多孔平衡流量计具有精度高、直管段要求低、永久压力损失少、耐脏污不易堵、长期稳定性好、流量测量范围宽、可测量高温、高压介质等特点。可测管径15~3 000 mm,直管段长度前0.5D~2D、后0.5D~2D,精度等级可达0.3%~0.5%,量程比20:1~30:1。该流量计适合硫酸装置副产蒸汽流量测量,既可确保精度,又能减少投资和运行维护费用。%Structure,characteristics and working principle of balanced flow meter with multi-hole orifice are described. Compared with traditional differential pressure flow meter,balanced flow meter has some characteristics such as high accuracy,low requirements for straight pipe,low permanent pressure loss,resistance to dirt and block, long-term stability,wide measurement range,high measurement temperature and high media pressure.The flow meter has measurable tube diameter of 15-3 000 mm and requires upstream straight run of pipe of 0.5D-2D and downstream one of 0.5D-2D with accuracy class of 0.3%-0.5%and range ratio of 20:1 -30:1.The flow meter is suited to measurement of by-product steam flow of sulphuric acid plant for high accuracy,less investment,operation and maintenance costs.

  3. Integrating Retinoic Acid Signaling with Brain Function

    Science.gov (United States)

    Luo, Tuanlian; Wagner, Elisabeth; Drager, Ursula C.

    2009-01-01

    The vitamin A derivative retinoic acid (RA) regulates the transcription of about a 6th of the human genome. Compelling evidence indicates a role of RA in cognitive activities, but its integration with the molecular mechanisms of higher brain functions is not known. Here we describe the properties of RA signaling in the mouse, which point to…

  4. Coordinate induction of hepatic fatty acyl-CoA oxidase and P4504A1 in rat after activation of the peroxisome proliferator-activated receptor (PPAR) by sulphur-substituted fatty acid analogues.

    Science.gov (United States)

    Demoz, A; Vaagenes, H; Aarsaether, N; Hvattum, E; Skorve, J; Göttlicher, M; Lillehaug, J R; Gibson, G G; Gustafsson, J A; Hood, S

    1994-09-01

    1. In the liver of rat fed a single dose of 3-thia fatty acids, 3-dithiahexadecanedioic acid (3-thiadicarboxylic acid) and tetradecylthioacetic acid, steady-state levels of P4504A1 and fatty acyl-CoA oxidase mRNAs increased in parallel. The increases were significant 8 h after administration, reaching a maximum after 12 h and decreased from 12 to 24 h after administration. 2. The corresponding enzyme activities of P4504A1 and fatty acyl-CoA oxidase were also induced in a parallel manner by the 3-thia fatty acids. The enzyme activities were significantly increased 12 h after administration and increased further after 24 h. This may reflect a possible effect of the 3-thia fatty acids not only on mRNA levels, but also on the translation and degradation rate of the two enzymes. 3. Repeated administration of 3-thia fatty acids resulted in an increase of the specific P4504A1 protein accompanied with an increased lauric acid hydroxylase activity. The correlation between induction of P4504A1 and fatty acyl-CoA oxidase mRNAs and their enzyme activities may reflect a coordinated rather than a causative induction mechanism, and that these genes respond to a common signal. This suggests that the increased P450 activity may not be responsible or be a prerequisite for fatty acyl-CoA oxidase induction. 4. Since the peroxisome proliferator-activated receptor (PPAR) plays a role in mediating the induction of fatty acyl-CoA oxidase, we analysed the activation of PPAR by fatty acids and sulphur-substituted analogues utilizing a chimera between the N-terminal and DNA-binding domain of the glucocorticoid receptor and the putative ligand-binding domain of PPAR. Arachidonic acid activated this chimeric receptor in Chinese hamster ovary cells. Inhibitors of P450 did not affect the activation of PPAR by arachidonic acid. Furthermore, dicarboxylic acids including 1,12-dodecanedioic acid or 1,16-hexadecanedioic acid only weakly activated the chimera. 3-Thidicarboxylic acid, however, was a

  5. Producción de Ácido Sulfúrico por Medio del Tratamiento de Gases Residuales Generados en la Tostación de Piritas Production of Sulphuric Acid by Treatment of Residual Gases Generated by Pyrite Roasting

    Directory of Open Access Journals (Sweden)

    Sergio Rosas

    2007-01-01

    Full Text Available Se presenta el estudio técnico-económico para la obtención de ácido sulfúrico por medio del proceso de contacto doble. Con base en las características de los gases residuales generados por la tostación de piritas se selecciona la tecnología de limpieza del efluente y el proceso de producción de ácido sulfúrico. Para la limpieza de los gases se establece utilizar un tren de separación conformado por un separador ciclónico, un lavador Venturi, un eliminador de neblina y dos precipitadores electrostáticos de neblina ácida. Además, para la síntesis de trióxido de azufre se diseña un convertidor catalítico de cuatro camas. Finalmente, se presentan la estimación de los costos de capital y la factibilidad económica para dos concentraciones de producto.A technical-economical study of the sulphuric acid production by the double-contact process is presented. Based on the characteristics of the residual gases produced by pyrite roasting the effluent cleaning technology and the sulphuric acid production process were selected. To clean out the gaseous effluent a separation train that consists in a cyclone separator, a Venturi washer, a mist eliminator, and two electrostatic precipitators were considered. Also, for the sulphur trioxide synthesis a four-bed catalytic converter was designed. Finally, the capital cost estimation and the economic feasibility for two product concentrations are presented.

  6. Adsorption of sulphuric acid on smectite from acidic aqueous solutions Adsorção de ácido sulfúrico em esmectita de soluções aquosas ácidas

    Directory of Open Access Journals (Sweden)

    E. L. Tavani

    1999-05-01

    Full Text Available The adsorption of sulphuric acid on smectite from acidic aqueous solutions was studied. The amounts of cations dissolved in each equilibrium solution were determined by chemical analysis. Simultaneously, the original smectite and the smectite after each test were characterized by infrared, X-ray diffraction and swelling index. The results obtained permitted us to determine that the substitutions of the exchange cations and the chemical attack occurred at very different acid concentrations and treatment times. It was established that during the acid treatment of the smectite, a progressive damage of its crystalline structure was produced. Finally, the influences of the substitution of exchange cations and of the chemical attack in the swelling index were determined.A adsorção de ácido sulfúrico em esmectita de soluções aquosas ácidas é estudada. As concentrações de cátions dissolvidos em cada solução em equilíbrio foram determinadas por análise química. As esmectitas original e após cada teste foram simultaneamente caracterizadas por infravermelho, difração de raios X e índice de crescimento. Os resultados obtidos permitiram determinar que as substituições dos cátions de troca e o ataque químico ocorreram em diferentes concentrações de ácido e tempos de tratamento. Foi verificado que durante o tratamento em ácido da esmectita foi produzido um dano progressivo da sua estrutura cristalina. Finalmente foram determinadas as influências da substituição dos cátions de troca e do ataque químico no índice de crescimento.

  7. A geophysiologist's thoughts on the natural sulphur cycle

    OpenAIRE

    Lovelock, J. E.

    1997-01-01

    The climate depends on the atmospheric abundance of sulphur aerosols at all levels up to the stratopause. Volcanoes, combustion and biological emissions all contribute and usually result in cooling. The history of this topic is lively and goes back at least to the eighteenth century with Benjamin Franklin's comments on the cooling effects of the sulphuric acid aerosol from the Icelandic volcano, Laki. Mitchell first drew attention to the potential cooling effects of combustion aerosols. Charl...

  8. 贵溪冶炼厂硫酸二系列干吸工序工艺特点剖析%Analysis of technological features of drying and absorption section in Guixi Smelter'No.2 sulphuric acid plant

    Institute of Scientific and Technical Information of China (English)

    王希林

    2001-01-01

    介绍1333t/d铜冶炼烟气制酸装置干吸工序的设计特点。通过提高空塔气速、增加分酸点和喷淋密度实现干吸塔的高效设计,以节约投资。干吸工序为泵后冷却流程,干吸塔采用低位布置,节省了酸泵能耗。泵槽为卧式,从根本上解决了进口硫酸对泵槽的冲刷腐蚀问题。干燥塔和吸收塔共用一个泵槽,为避免干燥系统的SO2串入吸收系统,干燥酸从一吸塔上酸管串入。整个系统共设置5个控制回路。%The design features of drying and absorption section in a 1333t/d sulphuric acid plant based on copper smelter off-gas are described. High efficiency design was conducted for cost saving by increasing empty tower gas velocity, acid distribution points and liquid rate. The drying and absorption section adopted a pump-after cooling process with low-position arragement of drying and absorption towers to decrease power requirement of pumps. Pump tank was designed in horizontal form, so the brushing corrosion by sulphuric acid was thoroughly avoided. A common pump tank was used for both drying and absorption towers. To prevent SO2 carrying from drying system to absorption system, drying acid was added to intermediate absorption tower at the inlet pipe. Five control circuits were set in the system.

  9. Sulphur poisoning of the active materials used in SOFCs

    Energy Technology Data Exchange (ETDEWEB)

    Cunningham, R.H.; Fowles, M. [Synetix Ltd. (United Kingdom); Ormerod, R.M.; Staniforth, J. [Keele Univ. (United Kingdom)

    2004-07-01

    This report summarises the work done and main results of a project examining the Rolls-Royce Integrated Planar Solid Oxide Fuel Cell in order to determine the impact of sulphur poisoning of the anode, and sulphur and carbon poisoning of the reforming catalyst. The reversibility/irreversibility of the damage caused by sulphur was examined along with the development of a strategy involving changing operating conditions, catalysts, and processing of the natural gas feed to protect the fuel cell, and methods to minimise the deposition of carbon. The deactivation of the reforming catalyst brought about by hydrogen sulphide addition to the methane/steam mixtures, the rate of the deactivation of anodes resulting from the addition of hydrogen sulphide, problems due to cell leakage, and the module porous support are discussed. Recommendation presented cover safe concentrations of sulphur, the desulphurisation of the fuel, and the prevention of carbon deposition on the support material.

  10. Design features of a sulphuric acid plant based on lead and zinc sintering machine off-gas%硫酸用新型耐蚀合金的研究与开发

    Institute of Scientific and Technical Information of China (English)

    刘焕安

    2001-01-01

    Design features of a 150kt/a sulphuric acid plant based on lead and zinc sintering machine off-gases are described. The plant adopted a single absorption technology including closed dilute-acid-scrubbing gas cleaning and ammonia-acid off-gas treatment. The dilute acid settling system,cooling water circulation system, installation of electrostatic precipitator, high-temperature absorption technology and acid distributor of drying and absorption section, and preheater, hot bypass and insulation of conversion section are emphasized in detail.%论述硫酸对金属腐蚀的特殊性和合金设计的基本原理。介绍高温浓硫酸用高硅不锈钢HD-1、合金球墨铸铁HD-3以及稀硫酸用高钼含氮奥氏体不锈钢HD-7、HD-11的研究开发和应用范围。

  11. 活性炭脱硫富集烟气制酸系统技术改造实践%Technological revamping of sulphuric acid plant based on off-gas enriched by activated carbon desulphurization

    Institute of Scientific and Technical Information of China (English)

    李强

    2012-01-01

    The process and problems of the sulphuric acid plant based on a new 450 m2 sintering machine off-gas which is enriched by activated carbon desulphurization are introduced. Some improvements were made in accordance with lower gas temperature at spray tower inlet, insufficient bubble column height, high dust content at the inlet of drying tower, serious acid accumulation in acid distributor groove and darken product acid color. After retrofitting, the system operated well and the product acid became clear and transparent.%介绍了新450m^2烧结机烟气活性炭脱硫富集烟气制酸系统流程和存在问题。针对喷淋塔进口烟气温度偏低、泡沫柱高度不足、干燥塔进口尘含量超高、分酸槽内酸泥堆积严重、成品酸色度差等问题采取有效改造措施。改造后系统运行正常,产品酸清澈透明。

  12. Autotrophic denitrification for treatment of wastewater with high concentration of sulphur and nitrogen compounds

    OpenAIRE

    Fajardo Ortiz, María del Carmen

    2011-01-01

    Anthropogenic activities have contributed to the imbalance of nitrogen and sulphur natural cycles which causes many negative effects in nature due to the emissions of sulphur and nitrogen compounds and their transformations, e.g. rain acid, eutrophication, bad odours etc. To avoid such negative effects on environment, effluents containing high concentrations of both nitrogen and sulphur compounds must be treated previously to their discharge. Nitrification/denitrification is the conventio...

  13. Sulphur tales from the early Archean world

    Science.gov (United States)

    Montinaro, A.; Strauss, H.

    2016-07-01

    Sedimentary and magmatic rocks and their distinct sulphur isotopic signatures indicate the sources and processes of sulphur cycling, in particular through the analysis of all four stable sulphur isotopes (32S, 33S, 34S and 36S). Research over the past 15 years has substantially advanced our understanding of sulphur cycling on the early Earth, most notably through the discovery of mass-independently fractionated sulphur isotopic signatures. A strong atmospheric influence on the early Archean global sulphur cycle is apparent, much in contrast to the modern world. Diverse microbially driven sulphur cycling is clearly discernible, but its importance for Earth surface environments remains to be quantified.

  14. Oil condensation boilers and problems with sulphur. Sulphur separation for oil-fired condensation boilers and flue gas scrubbers - six measurements at different boilers

    Energy Technology Data Exchange (ETDEWEB)

    Koebel, M.; Elsener, M.

    1988-11-01

    Three condensation boilers, one condensating scrubber boiler and two waste gas scrubbers were the objects of measurements made to determine to what degree sulphur is separated. The three condensation boilers which are only equipped with a condenser for the condensation of the combustion water shaved separation levels of between 0.5 and 3.5%. They are therefore not suitable for cutting the SO/sub 2/-emissions from the combustion of sulphur-containing fuel oil. The washer boilers showed better results (40-45%) despite the fact that it works with acid washing liquid (2.85 pH). To explain the high level of separation one must assume that under oxygen influence a large part of the sulphur dioxide is further oxidised to sulphuric acid. Alkaline washers showed very good separations of up to 90%. Here again a large part of the sulphur dioxide further oxidises to sulfates.

  15. Implications for global climate change from microbially-produced acid mine drainage

    Science.gov (United States)

    Norlund, K. L.; Hitchcock, A. P.; Warren, L. A.

    2009-05-01

    Microbial catalysis of sulphur cycling in acid mine drainage (AMD) environments is well known but the reaction pathways are poorly characterised. These reaction pathways involve both acid-consuming and acid- generating steps, with important consequences for overall AMD production as well as sulphur and carbon global biogeochemical cycles. Mining-associated sulphuric acid has been implicated in climate change through the weathering of carbonate minerals resulting in the release of 29 Tg C/year as carbon dioxide. Understanding of microbial AMD generation is based predominantly on studies of Acidithiobacillus ferrooxidans despite the knowledge that other environmentally common strains of bacteria are also active sulphur oxidizers and that microbial consortia are likely very important in environmental processes. Using an integrated experimental approach including geochemical experimentation, scanning transmission X-ray microscopy (STXM) and fluorescent in situ hybridization (FISH), we document a novel syntrophic sulphur metabolism involving two common mine bacteria: autotrophic sulphur oxidizing Acidithiobacillus ferrooxidans and heterotrophic Acidiphilium spp. The proposed sulphur geochemistry associated with this bacterial consortium produces 40-90% less acid than expected based on abiotic AMD models, with significant implications for both AMD mitigation and AMD carbon flux modelling. The two bacterial strains are specifically spatially segregated within a macrostructure of extracellular polymeric substance (EPS) that provides the necessary microgeochemical conditions for coupled sulphur oxidation and reduction reactions. STXM results identify multiple sulphur oxidation states associated with the pods, indicating that they are the sites of active sulphur disproportionation and recycling. Recent laboratory experimentation using type culture strains of the bacteria involved in pod-formation suggesting that this phenomenon is likely to be widespread in environments

  16. Sumpor u ugljenu (Sulphur in Coal

    Directory of Open Access Journals (Sweden)

    Rađenović, A.

    2004-12-01

    Full Text Available The presence of sulphur in coal possesses important environmetal problems in its usage. The sulphur dioxide (S02 emissions produced during coal combustion account for a significant proportion of the total global output of anthropogenic SO2. The extent of sulphur separation depends on several variables such as the form of sulphur in coal, intimacy of contact between minerals and the products of devolatilization. The total sulphur in coal varies in the range of 0.2 - 11 wt %, although in most cases it is beetwen 1 and 3 wt %. Sulphur occurs in a variety of both inorganic and organic forms. Inorganic sulphur is found mainly as iron pyrite, marcasite, pyrrhotite, sphalerite, galena, chalcopirite and as sulphates (rarely exceeds w = 0,1 %. Organic sulphur is found in aromatic rings and aliphatic functionalities usually as mercaptans, aliphatic and aryl sulfides, disulfides and thiophenes. Organic and pyritic sulphur quantities depend on coal rank. Higher rank coals tend to have a high proportion of labile sulphur. All the organic sulphur is bivalent and it is spread throughout the organic coal matrix. Sulphur occurs in all the macerals and most minerals. Vitrinite contains the major part of organic sulphur and metals. Elemental sulphur is produced during coal weathering. The depolymerization methods as pyrolysis and hydrogenation are very drastic methods wich change the structure of the coal and the sulphur groups. In the case of pyrolysis, high levels of desulphurization, in chars and additional production of liquid hydrocarbon can be achieved. Thiophenes and sulphides were the major sulphur components of tars from coal pyrolysis. Hyrdogen sulphide and the lower mercaptans and sulphides were found in the volatile matters. Hydrogen sulphide and thiophenes are practically the only sulphur products of coal hydrogenation. H2S is produced in char hydrodesulphurization. A number of options are available for reducing sulphur emissions including the

  17. 烧结烟气脱硫制酸净化工序的设计与生产实践%Design and production practice of clearing section in a sulphuric acid plant based on sintering flue gas desulphurization

    Institute of Scientific and Technical Information of China (English)

    李强; 吕彦强

    2011-01-01

    The composition and conditions of enriched sintering flue gas from dry activated carbon method desulphurization of Iron Plant of Taiyuan Iron Steel Group Co.are described.The gas is of low flow,high temperature, high SO_2 and dust content and contains ammonia,fluorine,chlorine,mercury and other harmful impurities. The dilute sulfuric acid washing process with spray tower,1 bubble column scrubber,gas colling tower,2 bubble column scrubber and two-stage wet electrostatic precipitatores is used and clearing equipment is specially designed and selected.The sulphuric acid plant based on a 450 m sintering machine flue gas has operated stably for more than one year and every index of clearing section reaches or exceeds design value,with clearing recovery of 99.01%and 1.4 mg/m~3 dust,and trace amount of sulphuric acid mist,HF,HCl and NH_3 in flue gas at the outlet of clearing section.%介绍了太原钢铁(集团)有限公司炼铁厂烧结机烟气活性炭干法脱硫富集SO_2烟气的组分和工况。该富集SO_2烟气流量小、温度高、高含硫、高含尘并含有氨、氟、氯、汞等有害杂质,设计采用喷淋塔一一级泡沫柱洗涤器—气体冷却塔—二级泡沫柱洗涤器—两级电除雾器稀酸洗工艺加以处理,并对净化设备进行了设计选型。炼铁厂450m~烧结机烟气脱硫制酸装置已稳定运行1年多时间,净化工序各项指标均达到或超过设计值,较好地解决了恶劣工况烧结烟气净化除杂问题,净化收率达到99.01%,净化工序出口烟气尘(ρ)1.4mg/m~3,硫酸雾、HF、HCl、NH_3等微量。

  18. Scarification with sulphuric acid of Schizolobium amazonicum Huber ex Ducke seeds - FABACEAE Escarificação com ácido sulfúrico de sementes de Schizolobium amazonicum Huber ex Ducke - FABACEAE

    Directory of Open Access Journals (Sweden)

    Eniel David Cruz

    2007-06-01

    Full Text Available Seed coat impermeability to water occurs in many species, including Schizolobium amazonicum Huber ex Ducke. To promote germination in seeds with coat impermeability the use of sulphuric acid (H2SO4 is recommended. The objective of this study was to identify a better time for the scarification with sulphuric acid for S. amazonicum seeds. The effect of scarification with sulphuric acid for 20, 40 and 60 min on germination and speed germination was studied for seeds that were either sowed immediately after scarification or after a 24-hour period of immersion in water. Seeds were sown on a mix of sand and sawdust (1:1. The experimental design was completely randomized with four replications of 50 seeds. The statistical analysis of germination was carried out at six, nine, 12, 15, 18, 21 and 24 days after sowing, in a factorial scheme. For speed germination the means were compared by the Tukey test. There was an interaction between treatments to overcome dormancy and immersion time after scarification in most evaluations. Immersion in water accelerated the beginning of germination. All treatments to overcome dormancy promoted seed germination. However, scarification for 60 min, showed better germination, 92% when immediately sown and 86.5% when sown after 24 hours. Speed germination index was highest for scarified seeds for 60 min followed by immersion in water. Scarification for 60 min was the most efficient treatment to promote germination in S. amazonicum seeds.Impermeabilidade do tegumento da semente à água ocorre em muitas espécies, inclusive em Schizolobium amazonicum Huber ex Ducke. Para promover a germinação de sementes com tegumento impermeável um dos métodos recomendados é o uso de ácido sulfúrico (H2SO4. O objetivo desse estudo foi identificar o melhor tempo de escarificação com ácido sulfúrico na superação da dormência em sementes de S. amazonicum, escarificadas durante 20, 40 e 60 minutos. Parte das sementes foi semeada

  19. Ações fisiológicas do calor e do ácido sulfúrico em sementes de Brachiaria brizantha cultivar marandu Physiological actions of heat and sulphuric acid on Brachiaria brizantha 'marandu' seeds

    Directory of Open Access Journals (Sweden)

    Leila Martins

    2006-01-01

    Full Text Available Objetivando aprimorar o método de aplicação de calor para a superação da dormência de sementes de Brachiaria brizantha cultivar Marandu, foi estudado o comportamento fisiológico de amostras de dez lotes de sementes dessa forrageira, com taxas de dormência superiores a 25%, quando expostas à temperatura de 70 ºC por 5, 10, 15, 20, 25 e 30 horas e à imersão em ácido sulfúrico concentrado por 15 minutos. No início (efeito imediato e após seis meses (efeito latente de armazenamento em condições ambientes não controladas, foram feitas as seguintes avaliações: teor de água, germinação, viabilidade pelo tetrazólio, emergência em areia, índice de velocidade de emergência e comprimento da parte aérea das plântulas. Pelos resultados verificou-se que as exposições das sementes a 70 ºC ou a ácido sulfúrico concentrado reduzem a taxa de dormência e favorecem o desempenho fisiológico. Após seis meses de armazenamento, as sementes submetidas a 70 ºC por 5 horas mostram desempenho superior às dos demais tratamentos.Aiming at to improve the methodology for application of heat to break dormancy seeds of Brachiaria brizantha `Marandu', the physiological performance of samples of ten seed lots of this forage, with dormancy indices superior to 25%, was studied after exposure to 70 ºC for 5, 10, 15, 20, 25 and 30 hours and immersion in concentrated sulphuric acid for 15 minutes. At the beginning (immediate effect and after six months (latent effect storage under ambient uncontrolled conditions, the following evaluations were made: water content, germination, tetrazolium viability, sand emergence, speed of emergence index and shoot length. Results indicated that exposure of seeds to 70 ºC or to concentrated sulphuric acid reduce the dormancy rate and favor the physiological performance; after six months, the seeds submitted to 70 ºC for 5 hours show performance superior to those of the other treatments.

  20. Geochemistry: Sulphur from heaven and hell

    Science.gov (United States)

    Dauphas, Nicolas

    2013-09-01

    Fingerprints of sulphur isotopes in rocks from the ridge beneath the Atlantic Ocean suggest that a substantial fraction of sulphur at Earth's surface is left over from the formation of the planet's core. See Letter p.208

  1. Being green on sulphur: Targets, measures and side-effects

    DEFF Research Database (Denmark)

    Kontovas, Christos A.; Panagakos, George; Psaraftis, Harilaos N.

    2016-01-01

    deep-sea trades. Even though the amounts of SOx produced by ships are substantially lower than CO2, SOx emissions are highly undesirable as they cause acid rain and undesirable health effects in humans and animals. To mitigate these adverse environmental effects, the international shipping community...... has taken substantial policy measures. With the introduction of new limits for the content of sulphur in marine fuels in Northern European and North American sea areas, short-sea companies operating in these areas will face substantial additional cost. As of 1/1/2015, international regulations...... stipulate, among other things, a 0.1%limit in the sulphur content of marine fuels, or equivalent measures limiting the percent of SOx emissions to the same amount. As low-sulphur fuel is substantially more expensive than HFO, there is little or no room within these companies current margins to absorb...

  2. A geophysiologist's thoughts on the natural sulphur cycle

    Science.gov (United States)

    Lovelock, J. E.

    1997-01-01

    The climate depends on the atmospheric abundance of sulphur aerosols at all levels up to the stratopause. Volcanoes, combustion and biological emissions all contribute and usually result in cooling. The history of this topic is lively and goes back at least to the eighteenth century with Benjamin Franklin's comments on the cooling effects of the sulphuric acid aerosol from the Icelandic volcano, Laki. Mitchell first drew attention to the potential cooling effects of combustion aerosols. Charlson and his colleagues proposed that emissions of dimethyl sulphide (DMS) from ocean algae might also be important. More recently, Lovelock and Kump drew attention to the decline of biological sulphur emissions with global warming and the possible consequence of a positive feedback on climate change. The geophysiological aspects, which arose from the Gaia hypothesis in the early 1970s, form an important part of the account that follows.

  3. Effect of sulphur forms on colour and residue of sulphur during the storage at drying grapes by sulphur

    Directory of Open Access Journals (Sweden)

    Boztepe Özlem

    2016-01-01

    Full Text Available Turkey is the world leader in the manufacture and export of seedless raisins. Requirement of golden bleached raisins is increasing in food Industry of especially cake, bread and pastry year by year. In this research, the lowest residual value and the practical realization of such production was intended to determine by drying grapes with application of sulphur. In this case, sulphur residue and colour situations were determined during 12-mounth-storage according to sulphur forms. In this study sulphur studies were applied by Vitis Vinifera cv. “Sultani Çekirdeksiz” with Na2S2O5, which is liquid source of sulphur and SO2, which is gas source of sulphur. SO2 application were studied during 3, 6 and 8 hours and liquid form of sulphur is Na2S2O5 that was used during by 10, 20 and 30 minutes. Applications were prepared with 3 replicates which contain 20 kg fresh grape in each replicate. In conclusion, changes in dried grape have been identified in point of colour (chroma and hue and the sulphur content was determined according to sulphur forms in packing. Gas form of sulphur (SO2 which was applied 3 hours, gave the best result during 12-mounth-storage for colour and sulphur residue.

  4. In-situ remediation strategy for enhanced microbial de-acidification of geogenic sulphuric acid mining lakes - mesocosmic studies; In situ-Sanierungsstrategie zur Foerderung der mikrobiellen Entsaeuerung von geogen schwefelsauren Bergbaurestseen - Mesokosmosstudien

    Energy Technology Data Exchange (ETDEWEB)

    Froemmichen, R.

    2001-07-01

    The author investigated whether neutralisation of acid mining lakes can be enhanced by adding low-cost, complex organic carbon sources. Subjects: Selection of a complex carbon source suited for stimulation of dissimilatory iron and sulfate reduction; design and observation of a near-natural landscape compartment (mesocosmos) at different scales as a preparation for the field study; Description of reactions in the mesocosmic lake water and sediment; Assessment of neutralisation equivalents and neutralisation rates on the basis of an identification of reduced iron and sulphur compounds. [German] Die Hypothese, dass durch Zugabe kostenguenstiger komplexer organischer Kohlenstoffquellen in die sedimentnahe Wasserzone eines sauren Tagebaurestsees seeinterne Neutralisierungsprozesse gefoerdert werden, liegt dieser Arbeit zu Grunde. Seeinterne Neutralisationsprozesse, wie die dissimilatorische Eisen- und Sulfatreduktion, fuehren ueber die Akkumulierung von reduzierten Eisen- und Schwefelverbindungen im Sediment zur Alkalinitaetsbildung im Gewaessersystem und im Seewasser zu hoeheren pH-Werten. Daher leiten sich folgende Ziele fuer diese Arbeit ab: - Auswahl einer geeigneten komplexen Kohlenstoffquelle zur Stimulierung der dissimilatorischen Eisen- und Sulfatreduktion - Design und Beobachtung eines naturnahen Landschaftsausschnittes (Mesokosmos) unterschiedlicher Massstabsebenen in Vorbereitung fuer die Fallstudie im Freiland - Beschreibung von Stoffumsetzungen im Seewasser und -sediment der Mesokosmen - Abschaetzung von Neutralisationsaequivalenten und Bestimmung von Neutralisationsraten anhand der Identifizierung reduzierter Eisen- und Schwefelverbindungen. (orig.)

  5. 含硫氨基酸对獭兔生长及被毛发育的影响%Influences of Sulphur-Amino Acids on Growth and Hair Coat Development of Rex Rabbits

    Institute of Scientific and Technical Information of China (English)

    傅祥超; 文斌; 汪平; 张凯; 刘汉中

    2013-01-01

    In order to determine the optimal supplemental levels of methionine and cysteine in diets and their correlations of influences on growth and hair coat development of Rex rabbits, the related indices of growth and hair development were measured. A total of 315 new born Rex rabbits with the same birthday were allocated into 7 groups at random in litters. There were 7 replicates in each group and 6 rabbits in each replicate. The rabbits in the control group were fed a basal diet which contained 0. 24% methionine and 0. 23% cysteine, and the rabbits in the experimental groups were fed the diets supplemented with 0.10% , 0. 25% and 0.40% methionine or cysteine based on the basal diet, respectively. The feeding trial lasted from birth to 151 days old. The results showed as follows; supplementation of sulphur-amino acids could increased the body weight at 151 days of age and average daily gain, and above indices in the 0. 25% and 0. 40% groups had significant differences compared with the control group (P 0. 05), while the average daily feed intake showed an increasing trend (P>0.05). Compared with the control group, completion ratio of molt and hair coat density in the 0. 25% and 0. 40% groups were significantly increased (P 0. 05). From the perspective of hair coat scores at 92 and 151 days of age, supplementation of sulphur-amino acids could not significantly boost the hair coat quality of rex rabbits (P >0. 05) , and hair coat quality only showed an increasing trend with the supplemental level increasing. No significant differences were found in the above indices between methionine and cysteine groups with the corresponding levels (P >0. 05). Growth curve-fitting suggested that supplemental level of sulphur-amino acids could only change the maximum growth rate, but had little effect on the adult body weight. These results indicate that both of methionine and cysteine can promote growth and enhance hair coat development of Rex rabbits, and 0.25% dosage is the optimal

  6. Photochemical Control of the Distribution of Water and Sulphuric Acid Aerosols in the Clouds and Upper Haze of Venus with Comparison to Venus Express SOIR Observations

    Science.gov (United States)

    Parkinson, C. D.; Gao, P.; Yung, Y. L.; Bougher, S. W.; Bardeen, C.

    2014-12-01

    Observations of the middle and lower cloud layers of Venus has established the water vapour mixing ratio there as ~ 30-35 ppm (Ignatiev et al. 1997), while more recent data suggests that the water vapor mixing ratio of the upper haze of Venus is ~ 1 ppm (Bertaux et al. 2007). The transition region between these two regimes, the upper cloud, is an active site of photochemistry and production of sulfuric acid, which occurs through the formation of SO3 from the oxidation of SO2, and subsequent reactions between SO3 and water. These reactions have been shown by Parkinson et al. (2014a, submitted) as capable of causing an order of magnitude decrease of the water vapor mixing ratio in the upper cloud and upper haze if the SO2 mixing ratio at the upper cloud base were increased by only ~20%, as the resulting high SO3 concentrations rapidly react with any available water to form sulfuric acid. The opposite is true when water is in high abundance. This is likely to have profound effects on the sulfuric acid clouds and hazes themselves, as 1) the depletion of either species will decrease the production rate of sulfuric acid and 2) the saturation vapor pressure of the cloud droplets increases with decreasing water fraction, and thus a "drying" of the clouds may result in decreased cloud thickness. In this work we will use the Venus microphysical cloud models of Gao et al. (2014) and Parkinson et al. (2014b, submitted) to simulate the sulfuric acid clouds and hazes of Venus from 40 to 100 km altitude and evaluate how their structure and particle sizes depend on the background water vapor profile and sulfuric acid production rate as determined by Parkinson et al. (2014a, submitted). We also show how they respond to transient episodes of increased/decreased SO2/H2O mixing ratios and discuss the plausibility of possible causes, such as volcanic activity.

  7. Removing sulphur oxides from a fluid stream

    Energy Technology Data Exchange (ETDEWEB)

    Katz, Torsten; Riemann, Christian; Bartling, Karsten; Rigby, Sean Taylor; Coleman, Luke James Ivor; Lail, Marty Alan

    2014-04-08

    A process for removing sulphur oxides from a fluid stream, such as flue gas, comprising: providing a non-aqueous absorption liquid containing at least one hydrophobic amine, the liquid being incompletely miscible with water; treating the fluid stream in an absorption zone with the non-aqueous absorption liquid to transfer at least part of the sulphur oxides into the non-aqueous absorption liquid and to form a sulphur oxide-hydrophobic amine-complex; causing the non-aqueous absorption liquid to be in liquid-liquid contact with an aqueous liquid whereby at least part of the sulphur oxide-hydrophobic amine-complex is hydrolyzed to release the hydrophobic amine and sulphurous hydrolysis products, and at least part of the sulphurous hydrolysis products is transferred into the aqueous liquid; separating the aqueous liquid from the non-aqueous absorption liquid. The process mitigates absorbent degradation problems caused by sulphur dioxide and oxygen in flue gas.

  8. Nitrogen and Sulphur Relations in Effecting Yield and Quality of Cereals and Oilseed Crops

    Directory of Open Access Journals (Sweden)

    B.K. Nad

    2001-01-01

    Full Text Available Nitrogen and sulphur, both vital structural elements, are especially needed for the synthesis of proteins and oils. Investigations revealed the required application of sulphur is one half to one third the amount of nitrogen, and the ratio becomes narrower in mustard (Brassica juncea L., followed by wheat and rice. The efficiency of an increased level of nitrogen required a proportionately higher amount of sulphur. A critical investigation on the effective utilization of applied vis-à-vis absorbed nitrogen in wheat and mustard envisaged accumulation of NO3-N in vegetative parts when sulphur remained proportionately low. Application of sulphur hastened the chemical reduction of absorbed NO3– for its effective utilization. The effect was more pronounced in mustard than in wheat. Easily available forms of sulphur, like ammonium sulphate and gypsum, as compared to pyrite or elemental sulphur, maintained adequate N to S ratio in rice, resulting in a reduction in the percent of unfilled grain, a major consideration in rice yield. A narrow N to S ratio, with both at higher levels, increased the oil content but raised the saponification value of the oil, a measure of free fatty acids. Whereas, a proportionately narrow N to S ratio at moderate dose resulted in adequately higher seed and oil yield with relatively low saponification value, associated with increased iodine value of the oil, indicating respectively low free fatty acids and higher proportion of unsaturated fatty acids, an index for better quality of the oil.

  9. Cation profiling of passive films on stainless steel formed in sulphuric and acetic acid by deconvolution of angle-resolved X-ray photoelectron spectra

    Energy Technology Data Exchange (ETDEWEB)

    Högström, Jonas, E-mail: jhogstrom@gmail.com; Fredriksson, Wendy, E-mail: wendy.fredriksson@kemi.uu.se; Edstrom, Kristina, E-mail: kristina.edstrom@kemi.uu.se; Björefors, Fredrik, E-mail: fredrik.bjorefors@kemi.uu.se; Nyholm, Leif, E-mail: leif.nyholm@kemi.uu.se; Olsson, Claes-Olof A., E-mail: drclabbe@kth.se

    2013-11-01

    An approach for determining depth gradients of metal-ion concentrations in passive films on stainless steel using angle-resolved X-ray photoelectron spectroscopy (ARXPS) is described. The iterative method, which is based on analyses of the oxidised metal peaks, provides increased precision and hence allows faster ARXPS measurements to be carried out. The method was used to determine the concentration depth profiles for molybdenum, iron and chromium in passive films on 316L/EN 1.4432 stainless steel samples oxidised in 0.5 M H{sub 2}SO{sub 4} and acetic acid diluted with 0.02 M Na{sub 2}B{sub 4}O{sub 7} · 10H{sub 2}O and 1 M H{sub 2}O, respectively. The molybdenum concentration in the film is pin-pointed to the oxide/metal interface and the films also contained an iron-ion-enriched surface layer and a chromium-ion-dominated middle layer. Although films of similar composition and thickness (i.e., about 2 nm) were formed in the two electrolytes, the corrosion currents were found to be three orders of magnitude larger in the acetic acid solution. The differences in the layer composition, found for the two electrolytes as well as different oxidation conditions, can be explained based on the oxidation potentials of the metals and the dissolution rates of the different metal ions.

  10. 由混合电镀污泥硫酸浸出液选择性沉淀分离铬的研究%Recovery of chromium from sulphuric acid leaching solutions of mixed electroplating sludge by selective precipitation

    Institute of Scientific and Technical Information of China (English)

    徐志峰; 赵洪兴; 王成彦; 袁文辉; 杨卜

    2015-01-01

    The recovery of Cr from the sulphuric acid leaching solutions of mixed electroplating sludge (MES) is studied. After the removal of Cu by solvent extraction, the selective phosphate precipitation is applied for the separation of Cr from Fe, Ni and Zn in the MES leaching solutions. The experimental results show that the precipitation of Cr can be carried out stably and effectively and the concentration of Cr in the solutions can be lowered down to about 0.04 g/L. Cr is efficiently enriched in the precipitates which contain 13% of Cr, 0.4 %of Ni, 0.1%of Fe and 0.2%of Zn,respectively,and could be further recovered as economic products.%研究由混合电镀污泥硫酸浸出液选择性分离回收铬的方法.浸出液经萃取提铜后,应用磷酸沉淀方法实现铬与铁、镍、锌的选择性分离.实验证明,该方法稳定有效,能够达到选择性沉淀铬的目的,沉淀后液中铬的浓度可降至0.04 g/L左右.沉铬渣含铬约13%,镍、铁、锌等杂质含量可分别降至0.4%、0.1%和0.2%左右.由磷酸铬渣可进一步综合回收铬并制取铬的经济产品.

  11. Design and modeling of an advanced marine machinery system including waste heat recovery and removal of sulphur oxides

    DEFF Research Database (Denmark)

    Frimann Nielsen, Rasmus; Haglind, Fredrik; Larsen, Ulrik

    2013-01-01

    In order to reduce the formation of acid rain and its harmful effects, stricter legislations on emissions of sulphur oxides from ships applies as of 2015 in emission control areas and globally in 2020 by the international maritime organization (IMO). Consequently, prices on low sulphur fuels...... of the machinery system. The wet sulphuric acid process has shown to be an effective way of removing sulphur oxides from flue gas of land-based coal fired power plants. Moreover, organic Rankine cycles are suitable for heat to power conversion for low temperature heat sources. This paper is aimed at designing......-stroke diesel engine and a conventional waste heat recovery system. The results suggest that an organic Rankine cycle placed after the conventional waste heat recovery system is able to extract the sulphuric acid from the exhaust gas, while at the same time increase power generation from waste heat by 32...

  12. Evidence of atmospheric sulphur in the martian regolith from sulphur isotopes in meteorites.

    Science.gov (United States)

    Farquhar, J; Savarino, J; Jackson, T L; Thiemens, M H

    2000-03-02

    Sulphur is abundant at the martian surface, yet its origin and evolution over time remain poorly constrained. This sulphur is likely to have originated in atmospheric chemical reactions, and so should provide records of the evolution of the martian atmosphere, the cycling of sulphur between the atmosphere and crust, and the mobility of sulphur in the martian regolith. Moreover, the atmospheric deposition of oxidized sulphur species could establish chemical potential gradients in the martian near-surface environment, and so provide a potential energy source for chemolithoautotrophic organisms. Here we present measurements of sulphur isotopes in oxidized and reduced phases from the SNC meteorites--the group of related achondrite meteorites believed to have originated on Mars--together with the results of laboratory photolysis studies of two important martian atmospheric sulphur species (SO2 and H2S). The photolysis experiments can account for the observed sulphur-isotope compositions in the SNC meteorites, and so identify a mechanism for producing large abiogenic 34S fractionations in the surface sulphur reservoirs. We conclude that the sulphur data from the SNC meteorites reflects deposition of oxidized sulphur species produced by atmospheric chemical reactions, followed by incorporation, reaction and mobilization of the sulphur within the regolith.

  13. Sulphur dioxide removal from flue gases by electrogenerated aqueous reductants

    Energy Technology Data Exchange (ETDEWEB)

    Kelsall, G.H.

    1991-02-01

    A novel process is outlined in which aqueous absorbed SO{sub 2} species are reduced to elemental sulphur by electrogenerated reductants such as Ti{sup 3+}, V{sup 2+}, or Cr{sup 2+} ions, which do not form metal sulphides in acidic aqueous solutions. The generation of reductants in membrane-divided electrochemical reactors has been achieved with current efficiencies of {gt}90% and their oxidation by SO{sub 2} reduction has given S yields of {gt}90%.

  14. Extractable sulphate-sulphur, total sulphur and trace-element determinations in plant material by flow injection analysis

    Energy Technology Data Exchange (ETDEWEB)

    Heanes, D.L. (South Australian Department of Agriculture, Adelaide (Australia))

    1990-01-01

    A rapid, accurate and reproducible procedure for determining total sulphur(S) and trace elements (copper, zinc, manganese and iron) in plant material is described. Plant material is digested in culture tubes with a mixture of nitric and perchloric acids containing ammonium metavanadate and calcium chloride. In the acid digest, concentrations of total-S as sulphate are determined by turbidimetry and trace-elements by flame atomic absorption spectrophotometry using flow injection analysis. The results for a range of plant materials compare well with those obtained by conventional procedures for the same elements. The microprocessor controlled digestion and multielement assay procedure described here offers improved laboratory efficiencies in materials, time and cost effectiveness. The techniques should be particularly useful when plant tissues are in limited supply.

  15. Integral edge seals for phosphoric acid fuel cells

    Science.gov (United States)

    Granata, Jr., Samuel J. (Inventor); Woodle, Boyd M. (Inventor); Dunyak, Thomas J. (Inventor)

    1992-01-01

    A phosphoric acid fuel cell having integral edge seals formed by an elastomer permeating an outer peripheral band contiguous with the outer peripheral edges of the cathode and anode assemblies and the matrix to form an integral edge seal which is reliable, easy to manufacture and has creep characteristics similar to the anode, cathode and matrix assemblies inboard of the seals to assure good electrical contact throughout the life of the fuel cell.

  16. Volatile sulphur compounds elimination: A new insight in periodontal treatment

    Directory of Open Access Journals (Sweden)

    Ernie Maduratna Setiawatie

    2011-12-01

    Full Text Available Background: Recent evidences had demonstrated a link between halitosis and apoptosis in periodontitis. Periodontal pathogenic micro-organisms produce volatile sulphur compounds (VSCs. VSCs are toxic to periodontal tissue. Purpose: The purpose of this paper was to reveal the mechanism of VSCs in periodontal breakdown according to the most recent knowledges. Reviews: Halitosis is mainly attributed to VSCs such as hydrogen sulfide, methyl mercaptan and dimethyl sulfide. Several studies demonstrated a strong relationship between VSCs and periodontal disease progression. VSCs are released from amino acid breakdown from food, protein, cells, blood and saliva. In prone subjects, the VSCs may cause alteration in tissue integrity by increasing its permeability and facilitate the endotoxin to penetrate the tissue barrier. They may also causing apoptotic in gingival and periodontal tissue, which are considered the main pathogenesis in aggravating the periodontitis. VSCs may also initiate the increase of proinflammatory cytokines which is considered to have negative effects in host response. Conclusion: VSCs had been shown to have detrimental effects in gingival and periodontal ligament cells. The use of chlorine dioxine agent and topical antioxidant is beneficial in controlling the periodontal disease severity.Latar belakang: Penelitian terakhir menunjukkan adanya hubungan antara halitosis dengan terjadinya apoptosis pada periodontitis. Mikroorganisme penyebab periodontitis memproduksi volatile sulphur compounds (VSCs yang bersifat toksik terhadap jaringan periodontal. Tujuan: Tujuan penulisan ini adalah membahas mekanisme VSCs dalam menyebabkan kerusakan periodontal berdasarkan penelitian terakhir yang ada. Tinjauan pustaka: Halitosis seringkali dikaitkan dengan timbulnya VSCs seperti hidrogen sulfida, metil merkaptan, dan dimetil sulfida. Penelitian terakhir menunjukkan bahwa VSCs yang dilepaskan dari pemecahan asam amino makanan ternyata memiliki

  17. Accidental sulphuric acid poisoning in a newborn

    African Journals Online (AJOL)

    2015-05-18

    May 18, 2015 ... tion showed dried blood on the lips, there was no hyper- aemia, swellings or ... on supportive therapy including: Nil per oral, oxygen therapy at 1.5L/ min ... GI bleeding with abdominal distension, severe pallor, cold extremities,.

  18. Effect of propionic acid on citric acid fermentation in an integrated citric acid-methane fermentation process.

    Science.gov (United States)

    Xu, Jian; Bao, Jia-Wei; Su, Xian-Feng; Zhang, Hong-Jian; Zeng, Xin; Tang, Lei; Wang, Ke; Zhang, Jian-Hua; Chen, Xu-Sheng; Mao, Zhong-Gui

    2016-03-01

    In this study, an integrated citric acid-methane fermentation process was established to solve the problem of wastewater treatment in citric acid production. Citric acid wastewater was treated through anaerobic digestion and then the anaerobic digestion effluent (ADE) was further treated and recycled for the next batch citric acid fermentation. This process could eliminate wastewater discharge and reduce water resource consumption. Propionic acid was found in the ADE and its concentration continually increased in recycling. Effect of propionic acid on citric acid fermentation was investigated, and results indicated that influence of propionic acid on citric acid fermentation was contributed to the undissociated form. Citric acid fermentation was inhibited when the concentration of propionic acid was above 2, 4, and 6 mM in initial pH 4.0, 4.5 and, 5.0, respectively. However, low concentration of propionic acid could promote isomaltase activity which converted more isomaltose to available sugar, thereby increasing citric acid production. High concentration of propionic acid could influence the vitality of cell and prolong the lag phase, causing large amount of glucose still remaining in medium at the end of fermentation and decreasing citric acid production.

  19. Integrated boiler, superheater, and decomposer for sulfuric acid decomposition

    Science.gov (United States)

    Moore, Robert; Pickard, Paul S.; Parma, Jr., Edward J.; Vernon, Milton E.; Gelbard, Fred; Lenard, Roger X.

    2010-01-12

    A method and apparatus, constructed of ceramics and other corrosion resistant materials, for decomposing sulfuric acid into sulfur dioxide, oxygen and water using an integrated boiler, superheater, and decomposer unit comprising a bayonet-type, dual-tube, counter-flow heat exchanger with a catalytic insert and a central baffle to increase recuperation efficiency.

  20. Integrated Micro-Chip Amino Acid Chirality Detector for MOD

    Science.gov (United States)

    Glavin, D. P.; Bada, J. L.; Botta, O.; Kminek, G.; Grunthaner, F.; Mathies, R.

    2001-01-01

    Integration of a micro-chip capillary electrophoresis analyzer with a sublimation-based extraction technique, as used in the Mars Organic Detector (MOD), for the in-situ detection of amino acids and their enantiomers on solar system bodies. Additional information is contained in the original extended abstract.

  1. 超重力技术在硫酸尾气脱硫中的工业化应用%Industrial application of high-gravity technology in tail gas desulphurization of sulphuric acid plant

    Institute of Scientific and Technical Information of China (English)

    王柏林; 袁纪文

    2011-01-01

    The structure and working principle of high-gravity rotating packed bed are described.Zhejiang Juhua Co.'s two sulphuric acid plants originally used two-stage ammonia desulphurization process with foam column and multi spray and impact device for tail-gas desulphurization.After revamping,a two-stage ammonia desulphurization process with foam column and high-gravity rotating packed bed is used.The 72 h performance test showed that,the gases emitting from new systems contained 74-429 mg/m^3 SO2,8.5-31.9 mg/m^3 H2SO4 and 11.7-27.9 mg/m^3 NH3.The plants can save about 283 500 yuan/a on SO2 emissions cost and increase about 715 000 yuan/a of ammonium sulphate/ammonium bisulphate product value.Economic and environmental benefits are considerable.%介绍了超重力机结构和工作原理。浙江巨化股份有限公司硫酸厂2套制酸装置的尾气脱硫系统原采用泡沫塔—复喷复挡装置两级氨法脱硫工艺,技术改造后采用泡沫塔—超重力机两级氨法脱硫工二艺。改造后72h性能考核表明,新脱硫系统排放尾气ρ(SO2)最高429mg/m^3、最低74mg/m^3,ρ(H2SO4)最高31.9mg/m^3、最低8.5mg/m^3,ρ(NH3)最高27.9mg/m^3、最低11.7mg/m^3。技术改造后硫酸厂每年可节省SO2排污费约28.35万元,增产亚硫酸铵/亚硫酸氢铵产品产值约71.5万元/a,经济效益和环境效益可观。

  2. Amino acids in the sedimentary humic and fulvic acids

    Digital Repository Service at National Institute of Oceanography (India)

    Sardessai, S.

    to the coastal sedimentary humic acids implying higher association of amino acids with the carbonaceous and fine grained sedimentary humic acids. Both the humic and fulvic acids are composed of neutral, acidic, basic, aromatic and sulphur containing amino acids....

  3. Effect of acetic acid on citric acid fermentation in an integrated citric acid-methane fermentation process.

    Science.gov (United States)

    Xu, Jian; Chen, Yang-Qiu; Zhang, Hong-Jian; Tang, Lei; Wang, Ke; Zhang, Jian-Hua; Chen, Xu-Sheng; Mao, Zhong-Gui

    2014-09-01

    An integrated citric acid-methane fermentation process was proposed to solve the problem of extraction wastewater in citric acid fermentation process. Extraction wastewater was treated by anaerobic digestion and then recycled for the next batch of citric acid fermentation to eliminate wastewater discharge and reduce water resource consumption. Acetic acid as an intermediate product of methane fermentation was present in anaerobic digestion effluent. In this study, the effect of acetic acid on citric acid fermentation was investigated and results showed that lower concentration of acetic acid could promote Aspergillus niger growth and citric acid production. 5-Cyano-2,3-ditolyl tetrazolium chloride (CTC) staining was used to quantify the activity of A. niger cells, and the results suggested that when acetic acid concentration was above 8 mM at initial pH 4.5, the morphology of A. niger became uneven and the part of the cells' activity was significantly reduced, thereby resulting in deceasing of citric acid production. Effects of acetic acid on citric acid fermentation, as influenced by initial pH and cell number in inocula, were also examined. The result indicated that inhibition by acetic acid increased as initial pH declined and was rarely influenced by cell number in inocula.

  4. Integrated separation process for isolation and purification of biosuccinic acid.

    Science.gov (United States)

    Kurzrock, Tanja; Schallinger, Stefan; Weuster-Botz, Dirk

    2011-01-01

    Biotechnologically produced succinic acid has the potential to displace maleic acid and its uses. Therefore, it is of high interest for the chemical, pharmaceutical, and food industry.In addition to optimized production strains and fermentation processes, an efficient separation of succinic acid from the aqueous fermentation broth is indispensable to compete with the current petrochemical production of succinic acid. Isolation and purification of succinic acid from an Escherichia coli fermentation broth were studied with two amine-based reactive extraction systems: (i) trihexylamine in 1-octanol and (ii) diisooctylamine and dihexylamine in a mixture of 1-octanol and 1-hexanol. Back extraction of succinic acid from the organic phase was carried out using an aqueous trimethylamine solution. The trimethylammonium succinate generated after back extraction was split with an evaporation-based crystallization.The focus was on process integration, for example, reuse of the applied amines for extraction and back extraction. It was shown that the maximum trimethylamine concentration for back extraction should not exceed the stoichiometric amount (2 mol trimethylamine/mol the succinic acid in the organic phase) to ensure maximal extraction yields with the reused organic phase in subsequent extractions. Moreover, mixer-settler extraction and back extraction of succinic acid were scaled up from the milliliter- to the liter-scale making use of liquid–liquid centrifuges. The overall yield was 83.5% of the succinic acid from thefermentation supernatant. The final purity of the succinic acid crystals was 99.5%. Organic phase and amines can easily be recycled and reused. © 2011 American Institute of Chemical Engineers

  5. Design and modeling of an advanced marine machinery system including waste heat recovery and removal of sulphur oxides

    DEFF Research Database (Denmark)

    Frimann Nielsen, Rasmus; Haglind, Fredrik; Larsen, Ulrik

    2014-01-01

    that an ORC placed after the conventional waste heat recovery system is able to extract the sulphuric acid from the exhaust gas, while at the same time increase the combined cycle thermal efficiency by 2.6%. The findings indicate that the technology has potential in marine applications regarding both energy...... the efficiency of machinery systems. The wet sulphuric acid process is an effective way of removing flue gas sulphur oxides from land-based coal-fired power plants. Moreover, organic Rankine cycles (ORC) are suitable for heat to power conversion for low temperature heat sources. This paper describes the design...

  6. Trading sulphur emissions under the Second Sulphur Protocol

    Energy Technology Data Exchange (ETDEWEB)

    Foersund, Finn R.; Naevdal, Eric

    1997-07-01

    Emission trading is a potent policy instrument in theoretical analyses of environmental policy. However, trading in emission quotas of non-uniformly dispersed pollutants requires that the offsetting quantities vary with location of sources. Such a system is not yet in use. The Second Sulphur Protocol for Europe makes it possible to try out a system of ``exchange rates`` through a clause allowing ``joint implementation`` of emission reductions. In this report, the authors investigate some properties of a system with exogenous exchange rates within a simultaneous trade model based on cost efficiency. Incorporation of constraints on depositions in third party countries may be necessary in order to get third party country cooperation. It is demonstrated that imposition of constraints is feasible, but it is also revealed what demands such incorporation places on the design of the institutional setting. Constraints on trade should only be introduced when the concern for the environment of the various receptors fail to be captured adequately by the calibration of the exchange rates. 16 refs., 2 figs., 3 tabs.

  7. Interrogating trees as archives of sulphur deposition

    Science.gov (United States)

    Wynn, P. M.; Loader, N. J.; Fairchild, I. J.

    2012-04-01

    A principal driver of climatic variability over the past 1,000 years and essential forcing mechanism for climate, are the changes in atmospheric composition resulting from sulphur aerosols. Natural and anthropogenic aerosols released into the atmosphere disrupt the radiative balance through backscattering and absorption of incoming solar radiation and increase cloud albedo by acting as condensation nuclei. Understanding the impact of sulphur emissions upon climate beyond the last few hundred years however is not straightforward and natural archives of environmental information must be explored. Tree-rings represent one such archive as they are widely distributed and preserve environmental information within a precisely dateable, annually resolved timescale. Until recently the sulphur contained within tree-rings has largely remained beyond the reach of environmental scientists and climate modelers owing to difficulties associated with the extraction of a robust signal and uncertainties regarding post-depositional mobility. Our recent work using synchrotron radiation has established that the majority of non-labile sulphur in two conifer species is preserved within the cellular structure of the woody tissue after uptake and demonstrates an increasing trend in sulphur concentration during the 20th century and during known volcanic events. Due to the clear isotopic distinction between marine (+21), geological (+10 to +30), atmospheric pollution (-3 to +9 ) and volcanic sources of sulphur (0 to +5), isotopic ratios provide a diagnostic tool with which changes in the source of atmospheric sulphur can be detected in a more reliable fashion than concentration alone. Sulphur isotopes should thereby provide a fingerprint of short lived events including volcanic activity when extracted at high resolution and in conjunction with high resolution S concentrations defining the event. Here we present methodologies associated with extracting the sulphur isotopic signal from tree

  8. Integrated process for preparing a carboxylic acid from an alkane

    Science.gov (United States)

    Benderly, Abraham; Chadda, Nitin; Sevon, Douglass

    2011-12-20

    The present invention relates to an integrated process for producing unsaturated carboxylic acids from the corresponding C.sub.2-C.sub.4 alkane. The process begins with performance of thermally integrated dehydrogenation reactions which convert a C.sub.2-C.sub.4 alkane to its corresponding C.sub.2-C.sub.4 alkene, and which involve exothermically converting a portion of an alkane to its corresponding alkene by oxidative dehydrogenation in an exothermic reaction zone, in the presence of oxygen and a suitable catalyst, and then feeding the products of the exothermic reaction zone to an endothermic reaction zone wherein at least a portion of the remaining unconverted alkane is endothermically dehydrogenated to form an additional quantity of the same corresponding alkene, in the presence of carbon dioxide and an other suitable catalyst. The alkene products of the thermally integrated dehydrogenation reactions are then provided to a catalytic vapor phase partial oxidation process for conversion of the alkene to the corresponding unsaturated carboxylic acid or nitrile. Unreacted alkene and carbon dioxide are recovered from the oxidation product stream and recycled back to the thermally integrated dehydrogenation reactions.

  9. Nanoparticle-sulphur "inverse vulcanisation" polymer composites.

    Science.gov (United States)

    Bear, Joseph C; Peveler, William J; McNaughter, Paul D; Parkin, Ivan P; O'Brien, Paul; Dunnill, Charles W

    2015-07-04

    Composites of sulphur polymers with nanoparticles such as PbS, with tunable optical properties are reported. A hydrothermal route incorporating pre-formed nanoparticles was used, and their physical and chemical properties evaluated by transmission and scanning electron microscopy, thermogravimetric and elemental analyses. These polymers are easily synthesised from an industrial waste material, elemental sulphur, can be cast into virtually any form and as such represent a new class of materials designed for a responsible energy future.

  10. Energy integration of nitric acid production using pinch methodology

    Directory of Open Access Journals (Sweden)

    Ivaniš Gorica R.

    2015-01-01

    Full Text Available Pinch methodology was applied to the heat exchangers network (HEN synthesis of nitric acid production. The integration is analyzed in two ways, and the results are presented as two different solutions: (i the first solution is based on the original heat transfer equipment arrangement, (ii in order to eliminate the shortages of the first solution the second HEN was obtained using process simulation with optimized process parameters. Optimized HEN, with new arrangement of heat exchangers, gave good results in energy and process optimization. [Projekat Ministarstva nauke Republike Srbije, br. P172063

  11. Effect of NPK fertilization and elemental sulphur on growth and yield of lowbush blueberry

    Directory of Open Access Journals (Sweden)

    M. STARAST

    2008-12-01

    Full Text Available The aim of the research was to determine the effect of fertilizers on the pH of former arable soils and on the growth and the yield of the lowbush blueberry (Vaccinium angustifolium Ait.. Lowbush blueberry fertilization experiments were established in 1999 at two locations – at Kärla, Saaremaa, West Estonia and at Vasula, Tartu County, South Estonia. Experimental sites were situated on different soils: soil pHKCl at Kärla was 5.5 and at Vasula 6.2. Elemental sulphur and acidifying fertilizers (ammonium sulfate, potassium sulfate and superphosphate were used in both plantations. Fertilizers were applied based on nutrient in the soil and sulphur was applied at 100 g m–2. Plant growth was recorded in 2001, 2002 and 2003. A positive influence of NPK fertilization on yield was found in both Kärla and Vasula, and yield were 336 g and 41 g higher compared to the control, respectively. The vegetative growth and yield of blueberry depended significantly on soil pH. Elemental sulphur increased soil acidity and on loamy sand soil did not increase plant productivity. The sulphur effect on soil pH began to decrease three years after application. Sulphur can be recommended to increase soil acidity in nutrient-rich soil but, not nutrient poor soil with light texture, where only NPK fertilizers were effective.;

  12. Lithium-sulphur battery with activated carbon cloth-sulphur cathode and ionic liquid as electrolyte

    Science.gov (United States)

    Swiderska-Mocek, Agnieszka; Rudnicka, Ewelina

    2015-01-01

    In this study a binder-free activated carbon cloth-sulphur (ACC-S) composite cathode is presented. Such a cathode was obtained using the impregnating technique of microporous activated carbon cloth with elemental melted sulphur. The surface morphology of an activated carbon cloth-sulphur electrode was studied using a scanning electron microscope (SEM), which was equipped with an EDX spectroscopy attachment. Electrochemical properties of the ACC-S composite cathode was tested in an ionic liquid electrolyte consisting of 1-ethyl-3-methylimidazolium bis(trifluoromethanesulphonyl)imide (EtMeImNTf2) and bis(trifluoromethanesulphonyl)imide (LiNTf2). The ACC-sulphur cathode working together with lithium anode was tested with the use of cyclic voltammetry (CV), galvanostatic charge/discharge cycles and electrochemical impedance spectroscopy (EIS). The capacity and cyclic stability of the ACC-S composite cathode were much better than those for the sulphur cathode (a mixture of sulphur from graphene nanoplatelets and carbon black) tested in the same ionic liquid electrolyte. The ACC-sulphur cathode showed good cyclability and coulombic efficiency (99%) with the ionic liquid electrolyte. The reversible capacity of the ACC-S|electrolyte|Li cell was ca. 830 mAh g-1 after 50 cycles.

  13. Sulphur mustard degradation on zirconium doped Ti-Fe oxides

    Energy Technology Data Exchange (ETDEWEB)

    Stengl, Vaclav, E-mail: stengl@iic.cas.cz [Department of Solid State Chemistry, Institute of Inorganic Chemistry AS CR v.v.i 250 68 Husinec-Rez (Czech Republic); Grygar, Tomas Matys [Department of Solid State Chemistry, Institute of Inorganic Chemistry AS CR v.v.i 250 68 Husinec-Rez (Czech Republic); Oplustil, Frantisek; Nemec, Tomas [Military Technical Institute of Protection Brno Veslarska 230, 628 00 Brno (Czech Republic)

    2011-09-15

    Highlights: {yields} New stechiometric materials for sulphur mustard degradation. {yields} High degree of degradation, more then 95% h{sup -1}. {yields} One-pot synthesis procedure. - Abstract: Zirconium doped mixed nanodispersive oxides of Ti and Fe were prepared by homogeneous hydrolysis of sulphate salts with urea in aqueous solutions. Synthesized nanodispersive metal oxide hydroxides were characterised as the Brunauer-Emmett-Teller (BET) surface area and Barrett-Joiner-Halenda porosity (BJH), X-ray diffraction (XRD), infrared (IR) spectroscopy, scanning electron microscopy (SEM) with energy-dispersive X-ray (EDX) microanalysis, and acid-base titration. These oxides were taken for an experimental evaluation of their reactivity with sulphur mustard (chemical warfare agent HD or bis(2-chloroethyl)sulphide). The presence of Zr{sup 4+} dopant tends to increase both the surface area and the surface hydroxylation of the resulting doped oxides in such a manner that it can contribute to enabling the substrate adsorption at the oxide surface and thus accelerate the rate of degradation of warfare agents. The addition of Zr{sup 4+} to the hydrolysis of ferric sulphate with urea shifts the reaction route and promotes formation of goethite at the expense of ferrihydrite. We discovered that Zr{sup 4+} doped oxo-hydroxides of Ti and Fe exhibit a higher degradation activity towards sulphur mustard than any other yet reported reactive sorbents. The reaction rate constant of the slower parallel reaction of the most efficient reactive sorbents is increased with the increasing amount of surface base sites.

  14. The useful application of sulphur-bound waste materials

    NARCIS (Netherlands)

    Alkemade, M.M.C.; Koene, J.I.A.

    1996-01-01

    An immobilization process is described which is based on sulphur (instead of cement) as a binding agent for the treatment of hazardous waste materials. Elemental sulphur is able to bind chemically metals such as mercury and, to a lesser extent, lead as metal sulphides. Furthermore, sulphur forms a

  15. The useful application of sulphur-bound waste materials

    NARCIS (Netherlands)

    Alkemade, M.M.C.; Koene, J.I.A.

    1996-01-01

    An immobilization process is described which is based on sulphur (instead of cement) as a binding agent for the treatment of hazardous waste materials. Elemental sulphur is able to bind chemically metals such as mercury and, to a lesser extent, lead as metal sulphides. Furthermore, sulphur forms a c

  16. Wearable salivary uric acid mouthguard biosensor with integrated wireless electronics.

    Science.gov (United States)

    Kim, Jayoung; Imani, Somayeh; de Araujo, William R; Warchall, Julian; Valdés-Ramírez, Gabriela; Paixão, Thiago R L C; Mercier, Patrick P; Wang, Joseph

    2015-12-15

    This article demonstrates an instrumented mouthguard capable of non-invasively monitoring salivary uric acid (SUA) levels. The enzyme (uricase)-modified screen printed electrode system has been integrated onto a mouthguard platform along with anatomically-miniaturized instrumentation electronics featuring a potentiostat, microcontroller, and a Bluetooth Low Energy (BLE) transceiver. Unlike RFID-based biosensing systems, which require large proximal power sources, the developed platform enables real-time wireless transmission of the sensed information to standard smartphones, laptops, and other consumer electronics for on-demand processing, diagnostics, or storage. The mouthguard biosensor system offers high sensitivity, selectivity, and stability towards uric acid detection in human saliva, covering the concentration ranges for both healthy people and hyperuricemia patients. The new wireless mouthguard biosensor system is able to monitor SUA level in real-time and continuous fashion, and can be readily expanded to an array of sensors for different analytes to enable an attractive wearable monitoring system for diverse health and fitness applications.

  17. Integrating nitric oxide into salicylic acid and jasmonic acid/ethylene plant defense pathways

    DEFF Research Database (Denmark)

    Mur, Luis A J; Prats, Elena; Pierre, Sandra

    2013-01-01

    Plant defence against pests and pathogens is known to be conferred by either salicylic acid (SA) or jasmonic acid (JA)/ethylene (ET) pathways, depending on infection or herbivore-grazing strategy. It is well attested that SA and JA/ET pathways are mutually antagonistic allowing defence responses...... to be tailored to particular biotic stresses. Nitric oxide (NO) has emerged as a major signal influencing resistance mediated by both signalling pathways but no attempt has been made to integrate NO into established SA/JA/ET interactions. NO has been shown to act as an inducer or suppressor of signalling along...... the cytoplasm to reduce TGA activation. In JA biosynthesis, NO will initiate the expression of JA biosynthetic enzymes, presumably to over-come any antagonistic effects of SA on JA-mediated transcription. NO will also initiate the expression of ET biosynthetic genes but a suppressive role is also observed...

  18. Sulphur mustard degradation on zirconium doped Ti-Fe oxides.

    Science.gov (United States)

    Štengla, Václav; Grygar, Tomáš Matys; Opluštil, František; Němec, Tomáš

    2011-09-15

    Zirconium doped mixed nanodispersive oxides of Ti and Fe were prepared by homogeneous hydrolysis of sulphate salts with urea in aqueous solutions. Synthesized nanodispersive metal oxide hydroxides were characterised as the Brunauer-Emmett-Teller (BET) surface area and Barrett-Joiner-Halenda porosity (BJH), X-ray diffraction (XRD), infrared (IR) spectroscopy, scanning electron microscopy (SEM) with energy-dispersive X-ray (EDX) microanalysis, and acid-base titration. These oxides were taken for an experimental evaluation of their reactivity with sulphur mustard (chemical warfare agent HD or bis(2-chloroethyl)sulphide). The presence of Zr(4+) dopant tends to increase both the surface area and the surface hydroxylation of the resulting doped oxides in such a manner that it can contribute to enabling the substrate adsorption at the oxide surface and thus accelerate the rate of degradation of warfare agents. The addition of Zr(4+) to the hydrolysis of ferric sulphate with urea shifts the reaction route and promotes formation of goethite at the expense of ferrihydrite. We discovered that Zr(4+) doped oxo-hydroxides of Ti and Fe exhibit a higher degradation activity towards sulphur mustard than any other yet reported reactive sorbents. The reaction rate constant of the slower parallel reaction of the most efficient reactive sorbents is increased with the increasing amount of surface base sites.

  19. Strange and non-strange baryon and antibaryon production in sulphur-tungsten and sulphur-sulphur interactions at 200 A Gev/c

    Energy Technology Data Exchange (ETDEWEB)

    Holme, A.K.

    1995-11-01

    The author has studied production of strange and multistrange baryons and antibaryons in central sulphur-tungsten, sulphur-sulphur, and lead-lead interactions at relativistic energies. The spectra of strange baryons and antibaryons provide information about the dynamics of hadronic matter under the extreme conditions realised in these collisions. The particle ratios allow the degree and the nature of the flavour equilibrium to be studied, while the transverse mass distributions provide independent information of the temperatures achieved. 143 refs.

  20. Strange and non-strange baryon and antibaryon production in sulphur-tungsten and sulphur-sulphur interactions at 200 A Gev/c

    Energy Technology Data Exchange (ETDEWEB)

    Holme, A.K.

    1995-11-01

    The author has studied production of strange and multistrange baryons and antibaryons in central sulphur-tungsten, sulphur-sulphur, and lead-lead interactions at relativistic energies. The spectra of strange baryons and antibaryons provide information about the dynamics of hadronic matter under the extreme conditions realised in these collisions. The particle ratios allow the degree and the nature of the flavour equilibrium to be studied, while the transverse mass distributions provide independent information of the temperatures achieved. 143 refs.

  1. Integrated Production of Xylonic Acid and Bioethanol from Acid-Catalyzed Steam-Exploded Corn Stover.

    Science.gov (United States)

    Zhu, Junjun; Rong, Yayun; Yang, Jinlong; Zhou, Xin; Xu, Yong; Zhang, Lingling; Chen, Jiahui; Yong, Qiang; Yu, Shiyuan

    2015-07-01

    High-efficiency xylose utilization is one of the restrictive factors of bioethanol industrialization. However, xylonic acid (XA) as a new bio-based platform chemical can be produced by oxidation of xylose with microbial. So, an applicable technology of XA bioconversion was integrated into the process of bioethanol production. After corn stover was pretreated with acid-catalyzed steam-explosion, solid and liquid fractions were obtained. The liquid fraction, also named as acid-catalyzed steam-exploded corn stover (ASC) prehydrolyzate (mainly containing xylose), was catalyzed with Gluconobacter oxydans NL71 to prepare XA. After 72 h of bioconversion of concentrated ASC prehydrolyzate (containing 55.0 g/L of xylose), the XA concentration reached a peak value of 54.97 g/L, the sugar utilization ratio and XA yield were 94.08 and 95.45 %, respectively. The solid fraction was hydrolyzed to produce glucose with cellulase and then fermented with Saccharomyces cerevisiae NL22 to produce ethanol. After 18 h of fermentation of concentrated enzymatic hydrolyzate (containing 86.22 g/L of glucose), the ethanol concentration reached its highest value of 41.48 g/L, the sugar utilization ratio and ethanol yield were 98.72 and 95.25 %, respectively. The mass balance showed that 1 t ethanol and 1.3 t XA were produced from 7.8 t oven dry corn stover.

  2. NA35: sulphur-gold collision

    CERN Multimedia

    1991-01-01

    In this image the real particles produced by the collision of a 6400 GeV sulphur ion with a gold target can be seen as they pass through a streamer chamber. Streamer chambers consist of a gas chamber through which a strong pulsed electric field is passed, creating sparks as a charged particle passes through it. The NA35 experiment, which was in operation in the 1980s, was part of CERN's ongoing heavy ion project.

  3. 滋阴润燥生津汤联合硫酸羟化氯喹治疗干燥综合征患者的临床疗效%Oneself can Nourish dry soup Combined Sulphuric acid Hydroxyl,the Clinical Curative effect Analysis of Chloroquine Treatment of Sjogren's Syndrome

    Institute of Scientific and Technical Information of China (English)

    张宝国

    2016-01-01

    Objective To study the oneself can nourish dry soup combined sulphuric acid hydroxyl chloroquine in effect in the treatment of sjogren's syndrome.Methods Choose 80 cases of patients with sjogren's syndrome,were randomly divided into control group and the treatment group,al 40 cases,the control group given sulfuric acid hydroxyl chloroquine treatment,the treatment group in the control group on the basis of joint oneself can nourish dry soup treatment,compared two groups of therapeutic effect.Results The treatment group effective rate was 95.0%,control group was 80.0%,the treatment group is significantly higher than control group(P<0.05).Conclusion For sjogren's syndrome using oneself can nourish dry soup combined sulphuric acid hydroxyl chloroquine treatment can improve symptoms, obvious effect,have clinical application value.%目的:探讨滋阴润燥生津汤联合硫酸羟化氯喹治疗干燥综合征患者的临床疗效。方法选取80例干燥综合征患者为研究对象,按随机数字表法分为对照组与试验组,各40例,对照组患者给予硫酸羟化氯喹治疗,试验组患者在对照组基础上联合滋阴润燥生津汤治疗,对比两组患者的治疗效果。结果试验组患者治疗总有效率为95.0%,对照组为80.0%,试验组明显高于对照组(P<0.05)。结论对于干燥综合征患者采用滋阴润燥生津汤联合硫酸羟化氯喹治疗能改善临床症状,效果显著。

  4. Does an all-sulphur analogue of heptamolybdate exist?

    Indian Academy of Sciences (India)

    Bikshandarkoil R Srinivasan

    2004-08-01

    The complexes [MoX4]2- (M = Mo; X = O or S) exist as the monomeric tetrahedral species in aqueous alkaline solutions. Acidification of tetraoxomolybdate results in the condensation of the tetrahedral units via a series of polyoxomolybdates leading to the ultimate formation of the trioxide MoO3. Heptamolybdate [Mo7O24]6- is the first major polyanion of the acidification reaction. In contrast, acidification of tetrathiomolybdates leads to the formation of amorphous molybdenum trisulphide via a dinuclear Mo(V) complex. The formation of the dinuclear Mo(V) complex precludes the formation of any higher nuclearity Mo(VI)-S complexes in aqueous solution. Thus it is shown that the all-sulphur analogue of heptamolybdate [Mo7S2]6- does not exist in alkaline medium and also cannot be isolated from aqueous acidic medium.

  5. Integrated acid mine drainage management using fly ash.

    Science.gov (United States)

    Vadapalli, Viswanath R K; Gitari, Mugera W; Petrik, Leslie F; Etchebers, Olivier; Ellendt, Annabelle

    2012-01-01

    Fly Ash (FA) from a power station in South Africa was investigated to neutralise and remove contaminants from Acid Mine Drainage (AMD). After this primary treatment the insoluble FA residue namely solid residue (SR) was investigated as a suitable mine backfill material by means of strength testing. Moreover, SR was used to synthesise zeolite-P using a two-step synthesis procedure. Furthermore, the zeolite-P was investigated to polish process water from the primary FA-AMD reaction. The main objective of this series of investigations is to achieve zero waste and to propose an integrated AMD management using FA. Fly Ash was mixed with AMD at various predetermined FA-AMD ratios until the mixtures achieved circumneutral pH or higher. The supernatants were then analyzed using Inductively Coupled Plasma Mass Spectrometry (ICP-MS) and Ion Chromatography (IC) for cations and anions respectively. The physical strength testing of SR was carried out by mixing it with 3% Ordinary Portland Cement (OPC) and curing for 410 days. Synthesis of zeolite-P using SR was carried out by two step synthesis procedure: ageing for 24 hours followed by a mild hydrothermal synthesis at 100°C for 4 days. The polishing of process water from primary AMD treatment using FA was ascertained by mixing the process water with zeolite at a liquid to solid ratio of 100:1 for 1 hour. The results indicated that FA can be successfully used to ameliorate AMD. High removal of major AMD contaminants Fe, Al, Mg, Mn and sulphate was achieved with the ash treatment and trace elements such as Zn, Ni, Cu and Pb were also removed by the FA. Strength testing over 410 days indicated that the material gained strength over the testing period. The maximum unconfined compressive strength and elastic modulus was observed to be approximately 0.3 MPa and 150 Mpa respectively. The X-ray diffraction (XRD) analysis of the synthesized product indicated that SR was successfully converted into zeolite-P with some mullite phase

  6. Simultaneous determination of nanomole amounts of sulphur dioxide and hydrogen sulphide by flow injection analysis with on-line preconcentration by means of capillary denuder tubes.

    Science.gov (United States)

    Achilli, Marco; Gács, Istvan

    2002-01-01

    A simple and rapid method for trace determination of SO2 and H2S in gaseous samples by using a flow injection system with on line preconcentration on capillary denuder is described. The gaseous samples are led through a 0.4 M sulphamic acid solution, retaining nitrogen dioxide, ammonia and hydrogen chloride. The sulphur dioxide is collected from the carrier gas stream (250 cm3 min-1) as sulphuric acid in a capillary denuder tube coated with a thin layer of 0.01-0.03 M hydrogen peroxide solution of 0.05 mM sulphuric acid; hydrogen sulphide passes into a second tube coated with 0.075 mM sodium sulphide solution of 0.1 M aqueous sodium hydroxide. The films containing the sulphuric acid and the sodium sulphide, respectively, are eluted with the corresponding circulating absorbent streams and pass through the detectors. Sulphuric acid is detected by conductimetry and sulphide is determined spectrophotometrically at 230 nm. If nanoequivalent amounts of H2S are present in the sample containing a large concentration of SO2 (SO2/H2S concentration ratio > 20), the sulphur dioxide is filtered out of the sample gas stream by solid sodium hydrogen carbonate. A limit of detection of 3.5 micrograms m-3 is obtained.

  7. Integrating nitric oxide into salicylic acid and jasmonic acid/ ethylene plant defense pathways.

    Science.gov (United States)

    Mur, Luis A J; Prats, Elena; Pierre, Sandra; Hall, Michael A; Hebelstrup, Kim H

    2013-01-01

    Plant defense against pests and pathogens is known to be conferred by either salicylic acid (SA) or jasmonic acid (JA)/ethylene (ET) pathways, depending on infection or herbivore-grazing strategy. It is well attested that SA and JA/ET pathways are mutually antagonistic allowing defense responses to be tailored to particular biotic stresses. Nitric oxide (NO) has emerged as a major signal influencing resistance mediated by both signaling pathways but no attempt has been made to integrate NO into established SA/JA/ET interactions. NO has been shown to act as an inducer or suppressor of signaling along each pathway. NO will initiate SA biosynthesis and nitrosylate key cysteines on TGA-class transcription factors to aid in the initiation of SA-dependent gene expression. Against this, S-nitrosylation of NONEXPRESSOR OF PATHOGENESIS-RELATED PROTEINS1 (NPR1) will promote the NPR1 oligomerization within the cytoplasm to reduce TGA activation. In JA biosynthesis, NO will initiate the expression of JA biosynthetic enzymes, presumably to over-come any antagonistic effects of SA on JA-mediated transcription. NO will also initiate the expression of ET biosynthetic genes but a suppressive role is also observed in the S-nitrosylation and inhibition of S-adenosylmethionine transferases which provides methyl groups for ET production. Based on these data a model for NO action is proposed but we have also highlighted the need to understand when and how inductive and suppressive steps are used.

  8. Integrating nitric oxide into salicylic acid and jasmonic acid/ ethylene plant defence pathways.

    Directory of Open Access Journals (Sweden)

    Luis A.J. Mur

    2013-06-01

    Full Text Available Plant defence against pests and pathogens is known to be conferred by either salicylic acid (SA or jasmonic acid (JA/ethylene (ET pathways, depending on infection or herbivore-grazing strategy. It is well attested that SA and JA/ET pathways are mutually antagonistic allowing defence responses to be tailored to particular biotic stresses. Nitric oxide (NO has emerged as a major signal influencing resistance mediated by both signalling pathways but no attempt has been made to integrate NO into established SA/JA/ET interactions. NO has been shown to act as an inducer or suppressor of signalling along each pathway. NO will initiate SA biosynthesis and nitrosylate key cysteines on TGA-class transcription factors to aid in the initiation of SA—dependent gene expression. Against this, S-nitrosylation of NONEXPRESSOR OF PATHOGENESIS-RELATED PROTEINS1 (NPR1 will promote the NPR1 oligomerisation within the cytoplasm to reduce TGA activation. In JA biosynthesis, NO will initiate the expression of JA biosynthetic enzymes, presumably to over-come any antagonistic effects of SA on JA-mediated transcription. NO will also initiate the expression of ET biosynthetic genes but a suppressive role is also observed in the S –nitrosylation and inhibition of s-adenosylmethionine transferases which provides methyl groups for ethylene production. Based on these data a model for NO action is proposed but we have also highlighted the need to understand when and how inductive and suppressive steps are used.

  9. On the effects of hydrocarbon and sulphur-containing compounds on the CCN activation of combustion particles

    Directory of Open Access Journals (Sweden)

    A. Petzold

    2005-05-01

    Full Text Available The European PartEmis project (''Measurement and prediction of emissions of aerosols and gaseous precursors from gas turbine engines'' was focussed on the characterisation and quantification of exhaust emissions from a gas turbine engine. A comprehensive suite of aerosol, gas and chemi-ion measurements were conducted under different combustor operating conditions and fuel sulphur concentrations. Combustion aerosol characterisation included on-line measurements of mass and number concentration, size distribution, mixing state, thermal stability of internally mixed particles, hygroscopicity, cloud condensation nuclei (CCN activation potential, and off-line analysis of chemical composition. Modelling of CCN activation of combustion particles was conducted using microphysical and chemical properties obtained from the measurements as input data. Based on this unique data set, the role of sulphuric acid coatings on the combustion particles, formed in the cooling exhaust plume through either direct condensation of gaseous sulphuric acid or coagulation with volatile condensation particles nucleating from gaseous sulphuric acid, and the role of the organic fraction for the CCN activation of combustion particles was investigated. It was found that particles containing a large fraction of non-volatile organic compounds grow significantly less at high relative humidity than particles with a lower content of non-volatile OC. Also the effect of the non-volatile OC fraction on the potential CCN activation is significant. While a coating of water-soluble sulphuric acid increases the potential CCN activation, or lowers the activation diameter, respectively, the non-volatile organic compounds, mainly found at lower combustion temperatures, can partially compensate this sulphuric acid-related enhancement of CCN activation of carbonaceous combustion aerosol particles.

  10. Design and operation of Taiyuan Iron & Steel' s sulphuric acid plant based on SO_2 from desulphurization and enrichment of sintering off-gas%太钢烧结烟气脱硫富集SO_2烟气制酸装置的设计与运行

    Institute of Scientific and Technical Information of China (English)

    涂瑞; 李强; 葛帅华

    2012-01-01

    太原钢铁(集团)有限公司炼铁厂2台烧结机烟气采用活性炭吸附法脱硫工艺。针对脱硫富集SO2烟气流量小、温度高、SO2浓度高、尘含量高并含有氟、氯、氨、汞等有害杂质的特点,烟气制酸设计采用喷淋塔—一级泡沫柱洗涤器—气体冷却塔—二级泡沫柱洗涤器—2级电除雾器稀酸洗净化、"3+1"ⅢⅠ-ⅣⅡ二转二吸工艺流程。2套制酸装置投产近1年时间,装置运行稳定,各项工艺指标均达到设计值,硫酸产量分别达到26,38 t/d,制酸尾气ρ(SO2)均小于或等于450 mg/m3,工业硫酸品质达到国家优等品标准。%The off-gas from two sintering machines was treated for desulphurization by activated carbon adsorption process in Iron Plant of Taiyuan Iron Steel.For the characteristics of low flow,high temperature,high SO2 and dust contents and existence of ammonia,fluorine,chlorine,mercury and other harmful impurities in desulphurization enriched off-gas,the plant adopted a cleaning section consisting of spray tower,1st stage froth column scrubber,gas cooling tower,2nd stage froth column scrubber and two-stage wet electrostatic precipitatores,and a "3+1" Ⅲ Ⅰ-Ⅳ Ⅱ double absorption process.The two plants have been operating for more than one year and every index reached design value,with tail gas SO2 concentration of both lower than 450 mg/m3,sulphuric acid production of 26 t/d and 38 t/d,respectively,and sulphuric acid quality up to the national premium grade requirement.

  11. Review of the origin of sulphur in DN-1 discharge and its implication for future development, Dauin prospect, central Philippines

    Energy Technology Data Exchange (ETDEWEB)

    Bayrante, L.F.; Hermoso, D.Z.; Candelaria, M.R. [PNOC-Energy Development Corp., Fort Bonifacio Makati City (Philippines)] [and others

    1997-12-31

    Well DN-1, the first exploratory well of the Dauin geothermal prospect discharged in 1983 substantial quantities of sulphur with a near-neutral pH fluid (pH 6.4 to 7.2) containing maximum chloride levels of 3,300 mg/kg, SO{sub 4} of 300 mg/kg; and high CO{sub 2} and H{sub 2}S relative to the production wells in Palinpinon Field to the north. The chemistry of DN-1 discharge-fluid and the origin of sulphur have been the cause of apprehension for any future development due to concerns on the presence of a possible acid resource southeast of Cuernos de Negros. A reinterpretation of the previous and new surface data was undertaken in 1992 and 1996, including the origin of sulphur, to evaluate the potential of Dauin for development. The results indicate that the sulphur in DN-1 is formed from partial oxidation of hydrogen sulphide derived from the neutralised-acid fluids formed by sulphur hydrolysis at shallow levels but distant from DN-1. The study argues for the presence of near neutral exploitable resource in the prospect area.

  12. Sulphur dioxide removal using activated sorbents

    Energy Technology Data Exchange (ETDEWEB)

    Warmuzinski, K.; Jaschik, M.; Jaschik, J.; Wasilewski, W.; Mrozowski, J. [Inst. Inzynierii Chemical PAN, Gliwice (Poland)

    2001-07-01

    Results are presented of experimental investigation of the dry flue gas desulphurisation (FGD) process at low temperatures using activated sorbents. Solid wastes (ashes) from the dry (with humidification) FGD plant are used as a sorbent. The influence of basic operating parameters on the efficiency of SO{sub 2} removal is determined. More than twofold sulphur dioxide removal efficiency is obtained using activated sorbents in comparison with the efficiency obtained in the process with dry sorbents. The possibility of reduction of sorbent consumption in the dry method of FGD with humidification is found.

  13. Determinación de la Efectividad de la Remediación de Suelos Accidentalmente Contaminados con Ácido Sulfúrico mediante Métodos Geofísicos Determination of the Remediation Effectiveness of Soils Accidentally Contaminated by Sulphuric Acid by Geophysical Methods

    Directory of Open Access Journals (Sweden)

    Ignacio D Coria

    2011-01-01

    Full Text Available Este trabajo muestra que el diagnóstico de suelos contaminados con sustancias peligrosas después de la remediación puede realizarse con técnicas no invasivas, en menos tiempo, con menor costo y evitando los riesgos de contaminación cruzada de muestras del método invasivo. Los métodos no invasivos utilizados para este caso particular de una contaminación accidental con ácido sulfúrico concentrado fueron el de inducción electromagnética y el método geoeléctrico. De acuerdo con los resultados obtenidos, se concluye que la utilización complementaria de ambos métodos permite realizar un diagnóstico correcto de la efectividad de la remediación.This work demonstrates that the diagnosis of soils that have been contaminated with dangerous substances after remediation can be done with non invasive techniques, with cost and time reduction, and avoiding the sample cross contamination risks of invasive methods. The non-invasive methods used in this particular case of accidental contamination with concentrated sulphuric acid were electromagnetic induction and geoelectric. According to the results, it is concluded that the complementary use of both methods allows making a correct diagnosis of the remediation effectiveness.

  14. Effect of Sulphur in Rainfall, Irrigation Water and Percocolating Water on Soil Sulphur in Jiangxi Province

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Ten rainfall and irrigation water-collecting posts were set up in different ecotype districts of Jiangxi Province, China, to quarterly measure S content in rainfall and irrigation water. A rainwater chemical composition-collecting device was used to collect the sulphur in rainfall, and the amount of sulphur adsorbed on the resin column in the device was determined. The soil percolating water was gathered using 6 lysimeters, built up according to the profile sequence of the red soil derived from red sandstone and the red soil derived from Quaternary red clay, separately. On the lysimeters peanuts, soybean and radish were grown in rotation. Two treatments were designed: without S addition and with S addition at a rate of 14 kg S ha-1. The SO42- contents in rainfall, irrigation water and soil percolating water were determined by the turbidimetry. The results in 1997 showed that the average annual S content in rainwater was 28.13 kg S ha-1, the average S content in irrigation water was 1.7 mg S L-1, and the average content of SO24- in soil percolation water was 2.30 kg S ha-1 year-1 and 4.70 kg S ha-1 year-1 in treatments without and with sulphur application, respectively. In Jiangxi Province, apart from the losses by runoff and leaching, the sulphur in rainfall available to crops is 7.3 kg S ha-1 year-1 and additional S application is required. When rice is grown, however, irrigation water can supply 6.9 kg S ha-1, which, along with the sulphur in rainfall, can almost meet the S requirement of one cropping of rice.

  15. Meeting future SO_2 emission challenges with Topsφe's new VK-701 LEAP5~(TM) sulphuric acid catalyst%以VK-701 LEAP5~(TM)催化剂应对未来硫酸工业SO_2排放挑战

    Institute of Scientific and Technical Information of China (English)

    KURTCHRISTENSEN

    2011-01-01

    介绍了托普索公司基于LEAP5~(TM)技术而开发的一种新型催化剂VK-701。该催化剂通过改进气体在催化熔融物中的传递效率和提高V~(5+)含量,在低温下对高浓度转化气具有极高的活性。在典型的4段一转一吸硫酸装置的最后一段装填VK-701,SO_2排放量较之装填含铯催化剂可减少20%~30%,较之装填含钾催化剂可减少30%~40%。在最有效的"3+1"二转二吸装置第三段装填VK-701,SO_2排放量可减少40%,尾气ρ(SO_2)可降低至175 mg/m~3。VK-701的高活性已在一转一吸硫磺制酸装置的工业运行中得到证实。%A new catalyst designated VK-701 develpped by Topsφe on the basis of its novel LEAP5~(TM) technology is introduced.The new catalyst offers exceptionally high activity at low temperature in converted strong gases because of improved gas transport deficiencies through the catalytic melt and higher V~(5+) content.SO_2 emissions from a typical 4-bed single-absorption sulphuric acid plant can be reduced by 20%-30%by loading VK-701 in the final bed compared to a caesium-promoted catalyst or by 30%- 40%compared to a standard potassium-promoted catalyst.SO_2 emissions from the most efficient double-absorption plants can typically be reduced by 40% when loading VK-701 in the third pass of a 3 + 1 plant and achieve down to 175 mg/m~3.Operating experience from a sulphur-burning single-absorption plant confirms the high activity of VK-701.

  16. Influence of zeolite treated with sulphuric acid and sodium hydroxide on the coagulation-flocculation process of drainage. Influencia de la zeolita tratada con acido sulfurico y con hidroxido de sodio en el proceso de coagulacion floculacion en aguas superficiales

    Energy Technology Data Exchange (ETDEWEB)

    Gutierrez Duque, M.; Herrera Vasconcelos, T.; Laria Piedra, N.

    1994-01-01

    The present paper has had as objective the treatment of natural zeolite from Tasajera with sulfuric acid and sodium hydroxide (residuals acid and basic from the regeneration of cationic and anionic resins of the ''Otto Parallada'' thermoelectric plant) at different times and concentrations, with a further comparison and testing of the effectiveness of the obtained zeolite in respect to the natural one as a coadyuvant of the coagulation-flocculation process in the treatment of superficial water. (Author)

  17. Distribution of atmospheric sulphur species over various wetland regions in the southeastern U.S.A.

    Science.gov (United States)

    Berresheim, Harald

    Atmospheric dimethylsulphide (DMS), sulphur dioxide (SO 2), aerosol non-seasalt sulphate (nss-SO 4 and methanesulphonate (MSA) were measured periodically at Sapelo Island, Georgia, during March-April 1989 and April-May 1990. The spring 1990 measurements also included the sulphur gases hydrogen sulphide (H 2S), carbonyl sulphide (COS) and carbon disulphide (CS 2). In August 1989 single measurements of these compounds were also conducted in various natural environments of southern Louisiana (coastal waters, saltwater marsh, brackish/freshwater marsh, swamp). The median DMS concentration over Sapelo Island was significantly higher in April-May 1990 (92 ppt) than in March-April 1989 (18 ppt) due to enhanced biogenic DMS emission in spring. Atmospheric DMS levels increased sharply (up to 560 ppt) during advection of polluted air from paper mills located on the coastal mainland. Results obtained from measurements in Louisiana suggest that biogenic sulphur fluxes from soils and/or vegetation are significantly enhanced durign rainfall. H 2S concentrations were highly variable at each study site. Corresponding values ranged consistently higher over swamps and marshes (300-820 ppt) compared to tidal flats (3-510 ppt). Generally, DMS was the dominant biogenic sulphur gas emitted from coastal environments while further inland H 2S was the dominant species. Over all environments studied the relative contribution from natural sulphur sources to atmospheric nss-SO 4 levels ranged between approximately 15 and 50% during the individual measurement periods. Major contributions were made from regional anthropogenic sources and, on the southeastern Atlantic coast, from additional long-range transport of air masses from Africa and Europe. The effects of these sources on aerosol and rainwater acidity levels over each region are discussed.

  18. Responses to betaine and inorganic sulphur of sheep in growth performance and fibre growth.

    Science.gov (United States)

    Nezamidoust, M; Alikhani, M; Ghorbani, G R; Edriss, M A

    2014-12-01

    Sulphur-containing amino acids (SAA) are essential and usually the first limiting amino acids for growth, milk and wool production. The keratin fibre that grows from epidermal tissue is rich in SAA. The rate of fibre growth and its S content are influenced by the availability of SAA. Betaine is a dietary source for a labile methyl group and actively participates in methionine metabolism by donating methyl groups for the remethylation of homocysteine to methionine. Ruminants are capable of synthesizing SAA from inorganic S sources, and most bacteria in the rumen can use inorganic S to meet their requirements for growth. The objective of this study was to examine whether betaine and an inorganic sulphur supplement could provide methyl groups and sulphur amino acids in a way that growth performance and wool production of ewes and lambs are improved. Treatments performed included betaine supplementation, sulphate supplementation and betaine plus sulphate supplementation with five replications for each treatment. The dry matter intake of the ewes was affected by betaine plus sulphate supplementation (p betaine plus sulphate supplementation increased (p 0.05) between treatments. In the ewes, plasma methionine concentration increased (p betaine plus sulphate treatment. No corresponding difference (p > 0.05) was observed in plasma methionine concentration in the lambs. It can be concluded that betaine plus sulphate supplementation has the potential to change wool characteristics in the ewes, while these compounds were without any effect on growth and wool production of the lambs. Combining the two supplements was advantageous.

  19. Systematic Procedure for Integrated Process Operation: Reverse Electro-Enhanced Dialysis (REED) during Lactic Acid Fermentation

    DEFF Research Database (Denmark)

    Prado Rubio, Oscar Andres; Jørgensen, Sten Bay; Jonsson, Gunnar Eigil

    2011-01-01

    The integration of lactic acid fermentation and Reverse Electro-Enhanced Dialysis (REED) is investigated based upon previously developed mathematical models. A goal driven process and operation design procedure is proposed and partially investigated. The conceptual analysis of the processes...

  20. Efficacy and phytotoicity of lime sulphur in organic apple production

    NARCIS (Netherlands)

    Holb, I.J.; Jong, de P.F.; Heijne, B.

    2003-01-01

    Curative and preventive efficacy and phytotoxicity of lime sulphur spray schedules, based on a warning system, were evaluated in the Netherlands during two growing seasons under field conditions. In most cases, lime sulphur treatments applied either curatively or preventively resulted in significant

  1. The economics of sulphur in heavy fuel oil

    Energy Technology Data Exchange (ETDEWEB)

    Morgan, T. (Coopers and Lybrand Deloitte (GB))

    1991-01-01

    The sulphur premium, the price differential between high and low sulphur fuel oil, has trended upwards in recent years as Western governments have imposed increasingly tighter limits on both the quality of fuel oil supplied and emissions of polluting gases from the burning of fuel oil. This trend has had a significant impact on the relative prices of sweet and sour crudes and the economics of refining and power generation, in addition to the prices of natural gas index-linked partly to heavy fuel oil under long-term contracts. In this article, an analysis is made of the economics of sulphur content in heavy fuel oil, the outlook for the sulphur premium in Western Europe and the broader implications for the oil and gas industries. It is argued that, in spite of ever-tightening environmental controls, there is probably only relatively limited scope for a further rise in the sulphur premium over the coming years. (author).

  2. Effects of corn meal and sulphuric acid on the production of cachaça Efeitos do fubá e ácido sulfúrico sobre a produção de cachaça

    Directory of Open Access Journals (Sweden)

    Francisco Vicente Gaiotto Cleto

    2009-10-01

    Full Text Available This work was carried out to evaluate the effects of using corn meal and treating yeasts with sulfuric acid on fermentation microorganisms, wine acidity, ethanol content and cachaça yield and composition. The experiment was arranged in randomized block design, in a 2x3 factorial with five replications. The methods applied in this study are recommended by distilleries. Results showed that the yeast sulfuric acid treatment transferred acidity to the fermenting juice, without any influence on yeast viability, ethanol content and cachaça yield. On the other hand, the acid treatment controlled lactic bacteria in the inoculum. Addition of corn meal increased the concentration of lactic bacteria in the end of the fermentation and increased the levels of higher alcohols in cachaça, especially propyl and isobutyl alcohol.Avaliou-se o efeito da adição do fubá de milho no mosto de xarope de cana e o tratamento ácido do pé-de-cuba sobre a microbiota do processo fermentativo, acidez do vinho, grau alcoólico, rendimento e composição da cachaça. O delineamento experimental utilizado foi o de blocos casualizados, no esquema fatorial 2x3 e cinco repetições. A metodologia empregada e as análises foram as recomendadas pelo setor aguardenteiro. Os resultados permitiram concluir que a adição do ácido sulfúrico no pé-de-cuba transferiu a acidez para o vinho, não influenciando na viabilidade das leveduras, rendimento e composição da cachaça. Por outro lado, a acidificação do meio controlou as bactérias láticas no pé-de-cuba. A adição do fubá aumentou a concentração de bactérias lácticas ao final do processo fermentativo e dos álcoois homólogos superiores na cachaça, particularmente, os álcoois propílico e isobutílico.

  3. A chemical perspective on transcriptional fidelity dominant contributions of sugar integrity revealed by unlocked nucleic acids

    DEFF Research Database (Denmark)

    Xu, Liang; Plouffe, Steven W; Chong, Jenny;

    2013-01-01

    Transcription unlocked: A synthetic chemical biology approach involving unlocked nucleic acids was used to dissect the contribution of sugar backbone integrity to the RNA Polymerase II (Pol II) transcription process. An unexpected dominant role for sugar-ring integrity in Pol II transcriptional...

  4. On the effects of organic matter and sulphur-containing compounds on the CCN activation of combustion particles

    Directory of Open Access Journals (Sweden)

    A. Petzold

    2005-01-01

    Full Text Available The European PartEmis project (Measurement and prediction of emissions of aerosols and gaseous precursors from gas turbine engines was focussed on the characterisation and quantification of exhaust emissions from a gas turbine engine. The combustion aerosol characterisation included on-line measurements of mass and number concentration, size distribution, mixing state, thermal stability of internally mixed particles, hygroscopicity, cloud condensation nuclei (CCN activation potential, and off-line analysis of chemical composition. Based on this extensive data set, the role of sulphuric acid coating and of the organic fraction of the combustion particles for the CCN activation was investigated. Modelling of CCN activation was conducted using microphysical and chemical properties obtained from the measurements as input data. Coating the combustion particles with water-soluble sulphuric acid, increases the potential CCN activation, or lowers the activation diameter, respectively. The adaptation of a Köhler model to the experimental data yielded coatings from 0.1 to 3 vol-% of water-soluble matter, which corresponds to an increase in the fraction of CCN-activated combustion particles from ≤10−4 to ≌10−2 at a water vapour saturation ratio Sw=1.006. Additional particle coating by coagulation of combustion particles and aqueous sulphuric acid particles formed by nucleation further reduces the CCN activation diameter. In contrast, particles containing a large fraction of non-volatile organic compounds grow significantly less at high relative humidity than particles with a lower content of non-volatile OC. The resulting reduction in the potential CCN activation with an increasing fraction of non-volatile OC becomes visible as a trend in the experimental data. While a coating of water-soluble sulphuric acid increases the potential CCN activation, or lowers the activation diameter, respectively, the non-volatile organic compounds, mainly found at

  5. Integrated acid mine drainage management using fly ash

    CSIR Research Space (South Africa)

    Vadapalli, VRK

    2012-01-01

    Full Text Available objective of this series of investigations is to achieve zero waste and to propose an integrated AMD management using FA. Fly Ash was mixed with AMD at various predetermined FA-AMD ratios until the mixtures achieved circumneutral pH or higher...

  6. Treatment of reduced sulphur compounds and SO2 by Gas Phase Advanced Oxidation

    DEFF Research Database (Denmark)

    Meusinger, Carl; Bluhme, Anders Brostrøm; Ingemar, Jonas L.

    2017-01-01

    Reduced sulphur compounds (RSCs) emitted from pig farms are a major problem for agriculture, due to their health and environmental impacts and foul odour. This study investigates the removal of RSCs, including H2S, and their oxidation product SO2 using Gas Phase Advanced Oxidation (GPAO). GPAO is...... compounds. The study demonstrates the ability of GPAO to control RSC emissions with a low energy input relative to many currently available techniques. (C) 2016 Elsevier B.V. All rights reserved......., assuming the observed particles were made of sulphuric acid. In a second set of experiments a range of RSCs at mixing ratios typically found in pig farms were treated using a larger industry-scale system (Q = 600-1200 m3/h) that included a wet scrubber. Removal efficiencies >90% were found for all...

  7. Integrated process of distillation with side reactors for synthesis of organic acid esters

    Science.gov (United States)

    Panchal, Chandrakant B; Prindle, John C; Kolah, Aspri; Miller, Dennis J; Lira, Carl T

    2015-11-04

    An integrated process and system for synthesis of organic-acid esters is provided. The method of synthesizing combines reaction and distillation where an organic acid and alcohol composition are passed through a distillation chamber having a plurality of zones. Side reactors are used for drawing off portions of the composition and then recycling them to the distillation column for further purification. Water is removed from a pre-reactor prior to insertion into the distillation column. An integrated heat integration system is contained within the distillation column for further purification and optimizing efficiency in the obtaining of the final product.

  8. Nucleic Acid-based Detection of Bacterial Pathogens Using Integrated Microfluidic Platform Systems

    Directory of Open Access Journals (Sweden)

    Carl A. Batt

    2009-05-01

    Full Text Available The advent of nucleic acid-based pathogen detection methods offers increased sensitivity and specificity over traditional microbiological techniques, driving the development of portable, integrated biosensors. The miniaturization and automation of integrated detection systems presents a significant advantage for rapid, portable field-based testing. In this review, we highlight current developments and directions in nucleic acid-based micro total analysis systems for the detection of bacterial pathogens. Recent progress in the miniaturization of microfluidic processing steps for cell capture, DNA extraction and purification, polymerase chain reaction, and product detection are detailed. Discussions include strategies and challenges for implementation of an integrated portable platform.

  9. Tribology properties of composite layer of CrMoCu alloy cast iron by combined treatment of ion nitrocarburizing and sulphurizing

    Institute of Scientific and Technical Information of China (English)

    MA Shi-ning; HU Chun-hua; LI Xin; QIU Ji

    2004-01-01

    Composite layer with nitrocarbonide and sulfide was made on the surface of CrMoCu alloy cast iron by combined treatment of ion nitrocarburizing and sulphurizing. The composite layer is composed of sulfide layer, nitrocarbonide hypo-surface layer and its diffusing layer, the size of sulfide globular grains distributing equably on the surface is in nano-micron-scale, and the phase structure of the composite layer is composed of FeS, FeS1-x, Fe2C and Fe3N. Under oil lubrication, sulphurized surface shows good scuffing-resistance only under low velocity, and nitrocarburized and sulphurized surface greatly improves the scuffing-resistance and wear-resistance of CrMoCu alloy cast iron, its integrated friction and wear properties are better than those of the plain and sulphurized surfaces under all the velocities.

  10. Integrated Microfluidic Nucleic Acid Isolation, Isothermal Amplification, and Amplicon Quantification

    OpenAIRE

    Mauk, Michael G.; Changchun Liu; Jinzhao Song; Bau, Haim H.

    2015-01-01

    Microfluidic components and systems for rapid (<60 min), low-cost, convenient, field-deployable sequence-specific nucleic acid-based amplification tests (NAATs) are described. A microfluidic point-of-care (POC) diagnostics test to quantify HIV viral load from blood samples serves as a representative and instructive example to discuss the technical issues and capabilities of “lab on a chip” NAAT devices. A portable, miniaturized POC NAAT with performance comparable to conventional PCR (poly...

  11. The effect of sulphur dioxide and oxygen on the viability and culturability of a strain of Acetobacter pasteurianus and a strain of Brettanomyces bruxellensis isolated from wine.

    Science.gov (United States)

    du Toit, W J; Pretorius, I S; Lonvaud-Funel, A

    2005-01-01

    The objective of this study was to investigate the effects of free molecular and bound forms of sulphur dioxide and oxygen on the viability and culturability of a selected strain of Acetobacter pasteurianus and a selected strain of Brettanomyces bruxellensis in wine. Acetic acid bacteria and Brettanomyces/Dekkera yeasts associated with wine spoilage were isolated from bottled commercial red wines. One bacterium, A. pasteurianus strain A8, and one yeast, B. bruxellensis strain B3a, were selected for further study. The resistance to sulphur dioxide and the effect of oxygen addition on these two selected strains were determined by using plating and epifluorescence techniques for monitoring cell viability in wine. Acetobacter pasteurianus A8 was more resistant to sulphur dioxide than B. bruxellensis B3a, with the latter being rapidly affected by a short exposure time to free molecular form of sulphur dioxide. As expected, neither of these microbial strains was affected by the bound form of sulphur dioxide. The addition of oxygen negated the difference observed between plate and epifluorescence counts for A. pasteurianus A8 during storage, while it stimulated growth of B. bruxellensis B3a. Acetobacter pasteurianus A8 can survive under anaerobic conditions in wine in the presence of sulphur dioxide. Brettanomyces bruxellensis B3a is more sensitive to sulphur dioxide than A. pasteurianus A8, but can grow in the presence of oxygen. Care should be taken to exclude oxygen from contact with wine when it is being transferred or moved. Wine spoilage can be avoided by preventing growth of undesirable acetic acid bacteria and Brettanomyces/Dekkera yeasts through the effective use of sulphur dioxide and the management of oxygen throughout the winemaking process.

  12. Evaluation of elemental sulphur in biodesulphurized low rank coals

    Energy Technology Data Exchange (ETDEWEB)

    L. Gonsalvesh; S.P. Marinov; M. Stefanova; R. Carleer; J. Yperman [Bulgarian Academy of Sciences, Sofia (Bulgaria). Institute of Organic Chemistry

    2011-09-15

    A new procedure for elemental sulphur (S{sup el}) determination in coal and its fractions is offered. It includes exhaustive CHCl{sub 3} extraction and subsequent quantitative analysis of the extracts by HPLC using C{sub 18} reversed phase column. Its application gives ground to achieve better sulphur balance and to specify the changes in the organic and elemental sulphur as a result of biotreatments. Two Bulgarian high sulphur containing coal samples, i.e. subbituminious (Pirin) and lignite (Maritza East), and one Turkish lignite (Cayirhan-Beypazari) are used. Prior to biotreatments, the samples are demineralized and depyritized. In the biodesulphurization processes, the applied microorganisms are: the white rot fungi 'Phanerochaeta Chrysosporium' - ME446 and the thermophilic and acidophilic archae 'Sulfolobus Solfataricus' - ATCC 35091. In the preliminary demineralized and depyritized coals, the highest presence of S{sup el} is registered, which is explained by their natural weathering. As a result of the implemented biotreatments, the amount of S{sup el} could be reduced in the range of 16.1-53.8%. The content of S{sub el} is also assessed as part of the total sulphur and organic sulphur. The following range of S{sup el} content is measured: 0.01-0.16 wt.% or 0.3-4.6% of total sulphur and 0.3-5.1% of organic sulphur. In this way, more precise information is obtained concerning the content of organic sulphur presence. 31 refs., 4 figs., 6 tabs.

  13. Microbial release of sulphur ions from atmospheric pollution deposits

    Energy Technology Data Exchange (ETDEWEB)

    Killhan, K.; Wainwright, M.

    1981-12-01

    The surfaces of leaves of Acer pseudoplatanus growing in areas exposed to heavy atmospheric pollution are covered with atmospheric pollution deposits (APD). Using scanning electron microscopy, micro-organisms were seen to be growing in intimate association with these deposits. The deposits contained sufficient carbon and nitrogen to support growth of the fungus Fusarium solani in culture and in autoclaved and non-sterilized soils; and sufficient reduced sulphur for the in vitro growth of Thiobacillus thioparus. When T. thioparus and F. solani were grown in medium supplemented with APD as sole carbon and nitrogen sources, increases in the concentrations of soluble S/sub 2/O/sup 2 -//sub 3/; S/sub 4/O/sup 2 -//sub 6/ and SO/sup 2 -//sub 4/ resulted. Similar increases also occurred when APD was added to complete fungal growth medium. Increases in LiCl/sub 2/-extractable sulphur-ions also occurred in fresh soil amended with APD, and in autoclaved soils containing APD, and inoculated with spores of F. solani. Arylsulphatase activity increased in fresh soils and in soils autoclaved and inoculated with F. solani when APD was added; suggesting sulphur mineralization, as well as sulphur oxidation, in the release of sulphur ions from APD. We concluded that APD can support microbial growth in vitro and in soils when provided as sole carbon and sulphur source; and that micro-organisms can release sulphur ions from this complex substrate. Microbial release of sulphur ions from APD can account in part for the increased concentrations of sulphur ions in heavy atmospheric-polluted soils.

  14. Microbial release of sulphur ions from atmospheric pollution deposits

    Energy Technology Data Exchange (ETDEWEB)

    Killham, K.; Wainwright, M.

    1981-12-01

    The surface of leaves of Acer pseudoplatanus growing in areas exposed to heavy atmospheric pollution are covered with atmospheric pollution deposits (APD). Using scanning electric microscopy, micro-organisms were seen to be growing in intimate association with these deposits. The deposits contained sufficient carbon and nitrogen to support growth of the fungus Fusarium solani in culture and in autoclaved and non-sterilized soils; and sufficient reduced sulphur for in vitro growth of Thiobacillus thioparus. When T. thioparus and F. solani were grown in medium supplemented with APD as sole carbon and nitrogen sources, increases in the concentrations of soluble S/sub 2/O/sub 3//sup 2/ btw/sup -/ and; S/sub 4/O/sub 6//sup 2 -/ and SO/sub 4//sup 2 -/ resulted. Similar increases also occurred when APD was added to complete fungal growth medium. Increases in LiCl/sub 2/-extractable sulphur-ions also occurred is fresh soil amended with APD, and in autoclaved soils containing APD, and inoculated with spores of F. solani. Arylsulphatase activity increased in fresh soils and in soils autoclaved and inoculated with F. solani when APD was added; suggesting sulphur mineralization, as well as sulphur oxidation, in the release of sulphur ions from APD. We conclude that APD can support microbial growth in vitro and in soils when provided as sole carbon and sulphur source; and that micro-organisms can release sulphur ions from this complex substrate. Microbial release of sulphur ions from APD can account in part for the increased concentrations of sulphur ions in heavy atmospheric-polluted soils.

  15. Integrated production of cellulosic bioethanol and succinic acid from industrial hemp in a biorefinery concept

    DEFF Research Database (Denmark)

    Kuglarz, Mariusz; Alvarado-Morales, Merlin; Karakashev, Dimitar Borisov

    2016-01-01

    The aim of this study was to develop integrated biofuel (cellulosic bioethanol) and biochemical (succinic acid) production from industrial hemp (Cannabis sativa L.) in a biorefinery concept. Two types of pretreatments were studied (dilute-acid and alkaline oxidative method). High cellulose recovery...... (> 95%) as well as significant hemicelluloses solubilization (49-59%) after acid-based method and lignin solubilization (35-41%) after alkaline H2O2 method were registered. Alkaline pretreatment showed to be superior over the acid-based method with respect to the rate of enzymatic hydrolysis and ethanol...

  16. Sulphur doping: a facile approach to tune the electronic structure and optical properties of graphene quantum dots

    Science.gov (United States)

    Li, Xueming; Lau, Shu Ping; Tang, Libin; Ji, Rongbin; Yang, Peizhi

    2014-04-01

    Sulphur-doped carbon-based materials have attracted a great deal of interest because of their important applications in the fields of oxygen reduction reactions, hydrogen storage, supercapacitors, photocatalysts and lithium ion batteries. Here, we report a new member of sulphur-doped carbon-based materials, i.e. sulphur doped graphene quantum dots (S-GQDs). The S-GQDs were prepared by a hydrothermal method using fructose and sulphuric acid as source materials. Absorption and photoluminescence investigations show that inter-band crossings are responsible for the observed multiple emission peaks. The incorporation of ~1 at% of S into the quantum dots can effectively modify the electronic structure of the S-GQDs by introducing S-related energy levels between π and π* of C. The additional energy levels in the S-GQDs lead to efficient and multiple emission peaks.Sulphur-doped carbon-based materials have attracted a great deal of interest because of their important applications in the fields of oxygen reduction reactions, hydrogen storage, supercapacitors, photocatalysts and lithium ion batteries. Here, we report a new member of sulphur-doped carbon-based materials, i.e. sulphur doped graphene quantum dots (S-GQDs). The S-GQDs were prepared by a hydrothermal method using fructose and sulphuric acid as source materials. Absorption and photoluminescence investigations show that inter-band crossings are responsible for the observed multiple emission peaks. The incorporation of ~1 at% of S into the quantum dots can effectively modify the electronic structure of the S-GQDs by introducing S-related energy levels between π and π* of C. The additional energy levels in the S-GQDs lead to efficient and multiple emission peaks. Electronic supplementary information (ESI) available: The detailed information of chemicals, the FTIR, Raman, the STEM image and the C, O and S mapping of S-GQDs, the PLE spectra of S-GQDs, and the fitting parameters of PL decay curves of S-GQDs. See DOI

  17. Sulphur and nitrogen supply - soil acidification and the absorption of nutrients in plants; Svovel og nitrogentilfoersel - jordforsuring og plantenes naeringstilgang

    Energy Technology Data Exchange (ETDEWEB)

    Abrahamsen, G.

    1996-01-01

    Ecologically, soil is of the greatest interest as a growth medium for plants, and which affects the quality of ground water and surface water. In this connection, the paper looks upon how the increased deposition of sulphur, nitrogen and hydrogen ions affect the quality of soil as a growth medium for plants. Topics cover: Interaction between soil and plants, effects of acid rain in soil, and the effects of acid rain on plants. 11 refs., 1 tab.

  18. Sulphur dioxide - current situation and health effects; Schwefeldioxid - aktuelle Situation und gesundheitliche Auswirkungen

    Energy Technology Data Exchange (ETDEWEB)

    Englert, N. [Umweltbundesamt, Berlin (Germany)

    2000-07-01

    Sulphur dioxide is a gaseous irritant. Health effects of SO{sub 2} as an individual pollutant are seen at relatively high concentrations, in asthmatics and under conditions of forced oral breathing, however, already at concentrations clearly below 1000 {mu}g/m{sup 3}. Nowadays, even during smog episodes such concentrations are hardly reached any more. In epidemiological studies, effects on mortality and respiratory diseases are described at daily average concentrations below 100 {mu}g/m{sup 3}. Therefore, in spite of undeniable success in reducing the immissions of sulphur dioxide and particulate matter in the Western industrial countries, increased daily mortality and other adverse health effects can happen during periods of increased air pollution, especially in the more polluted European regions. The relative importance of sulphur dioxide in comparison to particulate matter is still under discussion. In Western industrial countries, however, a higher importance of particulate matter is favoured. Atmospheric reactions with water droplets result in sulphurous acid or in sulphuric acid after atmospheric oxidation to SO{sub 3}. At least part of the effects ascribed to SO{sub 2} may be caused by acid aerosols formed in this way. This may also hold true for effects of SO{sub 2} under discussion, such as an induction of allergies and an increase in cancerogenic activity of pollutants. (orig.) [German] Schwefeldioxid ist ein Reizgas. Als Einzelsubstanz wirkt es erst in relativ hoher Konzentration, bei Asthmatikern und bei (forcierter) Mundatmung aber schon im Bereich von deutlich unter 1000 {mu}g/m{sup 3}. Solche Konzentrationen werden auch in Smog-Episoden heute kaum noch erreicht. In epidemiologischen Studien werden Wirkungen auf die Mortalitaet und auf die Haeufigkeit akuter Atemwegserkrankungen auch noch bei 24-h Mittelwerten unter 100 {mu}g/m{sup 3} beschrieben. Trotz unbestreitbarer Erfolge bei der Verminderung der Belastung durch SO{sub 2} und Feinstaub in den

  19. Integrated Microfluidic Nucleic Acid Isolation, Isothermal Amplification, and Amplicon Quantification

    Directory of Open Access Journals (Sweden)

    Michael G. Mauk

    2015-10-01

    Full Text Available Microfluidic components and systems for rapid (<60 min, low-cost, convenient, field-deployable sequence-specific nucleic acid-based amplification tests (NAATs are described. A microfluidic point-of-care (POC diagnostics test to quantify HIV viral load from blood samples serves as a representative and instructive example to discuss the technical issues and capabilities of “lab on a chip” NAAT devices. A portable, miniaturized POC NAAT with performance comparable to conventional PCR (polymerase-chain reaction-based tests in clinical laboratories can be realized with a disposable, palm-sized, plastic microfluidic chip in which: (1 nucleic acids (NAs are extracted from relatively large (~mL volume sample lysates using an embedded porous silica glass fiber or cellulose binding phase (“membrane” to capture sample NAs in a flow-through, filtration mode; (2 NAs captured on the membrane are isothermally (~65 °C amplified; (3 amplicon production is monitored by real-time fluorescence detection, such as with a smartphone CCD camera serving as a low-cost detector; and (4 paraffin-encapsulated, lyophilized reagents for temperature-activated release are pre-stored in the chip. Limits of Detection (LOD better than 103 virons/sample can be achieved. A modified chip with conduits hosting a diffusion-mode amplification process provides a simple visual indicator to readily quantify sample NA template. In addition, a companion microfluidic device for extracting plasma from whole blood without a centrifuge, generating cell-free plasma for chip-based molecular diagnostics, is described. Extensions to a myriad of related applications including, for example, food testing, cancer screening, and insect genotyping are briefly surveyed.

  20. Crystal structure of a NifS-like protein from Thermotoga maritima: implications for iron sulphur cluster assembly.

    Science.gov (United States)

    Kaiser, J T; Clausen, T; Bourenkow, G P; Bartunik, H D; Steinbacher, S; Huber, R

    2000-03-24

    NifS-like proteins are ubiquitous, homodimeric, proteins which belong to the alpha-family of pyridoxal-5'-phoshate dependent enzymes. They are proposed to donate elementary sulphur, generated from cysteine, via a cysteinepersulphide intermediate during iron sulphur cluster biosynthesis, an important albeit not well understood process. Here, we report on the crystal structure of a NifS-like protein from the hyperthermophilic bacterium Thermotoga maritima (tmNifS) at 2.0 A resolution. The tmNifS is structured into two domains, the larger bearing the pyridoxal-5'-phosphate-binding active site, the smaller hosting the active site cysteine in the middle of a highly flexible loop, 12 amino acid residues in length. Once charged with sulphur the loop could possibly deliver S(0) directly to regions far remote from the protein. Based on the three-dimensional structures of the native as well as the substrate complexed form and on spectrophotometric results, a mechanism of sulphur activation is proposed. The His99, which stacks on top of the pyridoxal-5'-phosphate co-factor, is assigned a crucial role during the catalytic cycle by acting as an acid-base catalyst and is believed to have a pK(a) value depending on the co-factor redox state.

  1. Interactions between selenium and sulphur nutrition in Arabidopsis thaliana.

    Science.gov (United States)

    White, P J; Bowen, H C; Parmaguru, P; Fritz, M; Spracklen, W P; Spiby, R E; Meacham, M C; Mead, A; Harriman, M; Trueman, L J; Smith, B M; Thomas, B; Broadley, M R

    2004-08-01

    Selenium (Se) is an essential plant micronutrient, but is toxic at high tissue concentrations. It is chemically similar to sulphur (S), an essential plant macronutrient. The interactions between Se and S nutrition were investigated in the model plant Arabidopsis thaliana (L.) Heynh. Arabidopsis plants were grown on agar containing a complete mineral complement and various concentrations of selenate and sulphate. The Se/S concentration ratio in the shoot ([Se](shoot)/[S](shoot)) showed a complex dependence on the ratio of selenate to sulphate concentration in the agar ([Se](agar)/[S](agar)). Increasing [S](agar) increased shoot fresh weight (FW) and [S](shoot), but decreased [Se](shoot). Increasing [Se](agar) increased both [Se](shoot) and [S](shoot), but reduced shoot FW. The reduction in shoot FW in the presence of Se was linearly related to the shoot Se/S concentration ratio. These data suggest (i) that Se and S enter Arabidopsis through multiple transport pathways with contrasting sulphate/selenate selectivities, whose activities vary between plants of contrasting nutritional status, (ii) that rhizosphere sulphate inhibits selenate uptake, (iii) that rhizosphere selenate promotes sulphate uptake, possibly by preventing the reduction in the abundance and/or activity of sulphate transporters by sulphate and/or its metabolites, and (iv) that Se toxicity occurs because Se and S compete for a biochemical process, such as assimilation into amino acids of essential proteins.

  2. Sulphur Spring: Busy Intersection and Possible Martian Analogue

    Science.gov (United States)

    Nankivell, A.; Andre, N.; Thomas-Keprta, K.; Allen, C.; McKay, D.

    2000-01-01

    Life in extreme environments exhibiting conditions similar to early Earth and Mars, such as Sulphur Spring, may harbor microbiota serving as both relics from the past as well as present day Martian analogues.

  3. Development of the floating sulphur biofilm reactor for sulphide ...

    African Journals Online (AJOL)

    driniev

    for sulphide oxidation in biological water treatment ... effluents produced in wastewater treatment systems. This was ... Biological sulphur cycle in the treatment of high sulphate .... Treatment of Contaminated Mine and Industrial Effluents. Final.

  4. Thermodynamic Equilibrium Diagrams of Sulphur-Chromium System

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The chemical and electrochemical equilibria in the presence of gaseous phase were investigated. Many substances, which consisted of sulphur and chromium, were considered. Various thermodynamic equilibria were calculated in different pressures. Calculation results were shown as log p―1/T and E―T diagrams. These diagrams may be used to study the corrosion of chromium in sulphur-containing circumstances. The diagrams are also used to thermodynami-cally determine the existence area of various substances and so on.

  5. Treatment for Sulphur Mustard Poisoning -A Review

    Directory of Open Access Journals (Sweden)

    K. Sugendran

    1998-04-01

    Full Text Available Sulphur mustard (SM is a chemical warfare agent of historical and current interest It is a wellknown blistering agent or vesicant SM was extensively used in world war I as a chemical weaponand has been stockpiled by several counbies since that time. SM serves as an ideal war gas and is favoured militarily for its ability to incapacitate rather than to kill. Its use resulted in large numbers ofcasualties requiring prolonged and intensive medical care. Despite Geneva Protocol of 1925, which categorically bnned the production, stockpiling and use of chemical weapons in wars, SM has beenused in several wars, including the Iran-Irnq war during the 1980s, which renewed interest in it.Though, the chemical we'dpons convention was signed by more than 160 counbies in 1993 and wassubsequently ratified by several counbies, the threat from this agent persists due to its clandestineusage during war and also by teITOrist groups. There is no effective and specific antidote for local andsystemic toxicity of SM despite scientific research for more than 75 years. Many compounds weretested as antidotes for SM, but very few of them have been shown to provide some protection. The present review is aimed at evaluating the treatment regime and other clinical measures used to treat  SM victims and the various drugs and chemicals screened as antidotes for SM poisoning in experimental animals.

  6. Integrated Microfluidic Nucleic Acid Isolation, Isothermal Amplification, and Amplicon Quantification.

    Science.gov (United States)

    Mauk, Michael G; Liu, Changchun; Song, Jinzhao; Bau, Haim H

    2015-10-20

    Microfluidic components and systems for rapid (microfluidic point-of-care (POC) diagnostics test to quantify HIV viral load from blood samples serves as a representative and instructive example to discuss the technical issues and capabilities of "lab on a chip" NAAT devices. A portable, miniaturized POC NAAT with performance comparable to conventional PCR (polymerase-chain reaction)-based tests in clinical laboratories can be realized with a disposable, palm-sized, plastic microfluidic chip in which: (1) nucleic acids (NAs) are extracted from relatively large (~mL) volume sample lysates using an embedded porous silica glass fiber or cellulose binding phase ("membrane") to capture sample NAs in a flow-through, filtration mode; (2) NAs captured on the membrane are isothermally (~65 °C) amplified; (3) amplicon production is monitored by real-time fluorescence detection, such as with a smartphone CCD camera serving as a low-cost detector; and (4) paraffin-encapsulated, lyophilized reagents for temperature-activated release are pre-stored in the chip. Limits of Detection (LOD) better than 10³ virons/sample can be achieved. A modified chip with conduits hosting a diffusion-mode amplification process provides a simple visual indicator to readily quantify sample NA template. In addition, a companion microfluidic device for extracting plasma from whole blood without a centrifuge, generating cell-free plasma for chip-based molecular diagnostics, is described. Extensions to a myriad of related applications including, for example, food testing, cancer screening, and insect genotyping are briefly surveyed.

  7. Concentration of volatile sulphur-containing compounds along the gastrointestinal tract of pigs fed a high-sulphur or a low-sulphur diet

    DEFF Research Database (Denmark)

    Poulsen, Henrik Vestergaard; Canibe, Nuria; Finster, Kai

    2010-01-01

    of their production or concentration along the GI-tract of the pig, and to what extent these parameters are influenced by the sulphur content of the diet. In order to address these questions, two diets with different sulphur content were formulated. Growing pigs were fed one of each diet during a minimum of three...... weeks after which they were killed and gas samples were removed from eight segments of the intact GI-tract and analysed for VSC, hydrogen, carbon dioxide and methane. The concentration of individual VSC in gas samples from the intact GI-tract varied between segments. The total concentration of VSC...

  8. Galactic chemical evolution of sulphur. Sulphur abundances from the [S i] λ1082 nm line in giants

    Science.gov (United States)

    Matrozis, E.; Ryde, N.; Dupree, A. K.

    2013-11-01

    Context. The Galactic chemical evolution of sulphur is still under debate. At low metallicities some studies find no correlation between [S/Fe] and [Fe/H], which is typical for α-elements, while others find [S/Fe] increasing towards lower metallicities, and still others find a combination of the two. Each scenario has different implications for the Galactic chemical evolution of sulphur. Aims: The aim of this study is to contribute to the discussion on the Galactic chemical evolution of sulphur by deriving sulphur abundances from non-local thermodynamic equilibrium (LTE) insensitive spectral diagnostics in disk and halo stars with homogeneously determined stellar parameters. Methods: We derived effective temperatures from photometric colours, surface gravities from stellar isochrones and Bayesian estimation, and metallicities and sulphur abundances from spectrum synthesis. We derived sulphur abundances from the [S i] λ1082 nm line in 39 mostly cool and metal-poor giants using 1D LTE MARCS model atmospheres to model our high-resolution near-infrared spectra obtained with the VLT, NOT, and Gemini South telescopes. Results: We derive homogeneous stellar parameters for 29 of the 39 stars. Our results argue for a chemical evolution of sulphur that is typical for α-elements, contrary to some previous studies that have found high sulphur abundances ([S/Fe] ≳ 0.6) for stars with -2.5 PPARC (UK), the NRC (Canada), CONICYT (Chile), the ARC, CNPq (Brazil), and CONICET (Argentina).Based partly on observations collected at the European Southern Observatory, Chile (ESO program 080.D-0675).Figures 3 and 4 are available in electronic form at http://www.aanda.org

  9. Functional and histologic assessment of rat gastric mucosa after chronic treatment with sulphurous thermal water.

    Science.gov (United States)

    Coruzzi, Gabriella; Adami, Maristella; Pozzoli, Cristina; Solenghi, Elvira; Grandi, Daniela

    2010-01-01

    The effect of a chronic (4 weeks) administration of sulphurous thermal water on gastric acid secretion and mucosal defense was investigated in rats. Animals were randomized to receive daily intake of tap water or of thermal water obtained from a local spa center (Tabiano, Parma, Italy). Rats were followed for one month as for water and food consumption, body weight and general conditions. At the end of the watering period, the following study protocols were carried out: (a) study of basal and stimulated gastric acid secretion under general anesthesia, and (b) study of the gastric mucosal resistance against the damage induced by ethanol and indomethacin in conscious rats. Basal acid secretion and the acid response to pentagastrin or to histamine were similar in rats assuming ordinary drinking water or thermal water. As for resistance to gastric damage, histological, but not macroscopic, evaluation revealed that rats which assumed thermal water were slightly more resistant to the gastrolesive effect of ethanol (either absolute or diluted). Again, when indomethacin was used as a noxious stimulus, no difference was noted between the two groups as for macroscopic damage; only a nonsignificant reduction of damage was observed histologically in stomachs of rats assuming thermal water. In conclusion, these results indicate that chronic treatment of rats with thermal water, rich in sulphur compounds, may have only minimal effects on the rat gastric mucosa and did not significantly affect mucosal defense mechanisms. The observed tendency to gastroprotection would possibly need further investigation with longer periods of administration. Copyright 2010 S. Karger AG, Basel.

  10. Optimization of the integrated citric acid-methane fermentation process by air stripping and glucoamylase addition.

    Science.gov (United States)

    Xu, Jian; Chen, Yang-Qiu; Zhang, Hong-Jian; Wang, Ke; Tang, Lei; Zhang, Jian-Hua; Chen, Xu-Sheng; Mao, Zhong-Gui

    2015-03-01

    To solve the problem of extraction wastewater in citric acid industry, an integrated citric acid-methane fermentation process was proposed. In the integrated process, extraction wastewater was treated by mesophilic anaerobic digestion and then reused to make mash for the next batch of citric acid fermentation. In this study, an Aspergillus niger mutant strain exhibiting resistance to high metal ions concentration was used to eliminate the inhibition of 200 mg/L Na(+) and 300 mg/L K(+) in anaerobic digestion effluent (ADE) and citric acid production increased by 25.0 %. Air stripping was used to remove ammonium, alkalinity, and part of metal ions in ADE before making mash. In consequence, citric acid production was significantly improved but still lower by 6.1 % than the control. Results indicated that metal ions in ADE synergistically inhibited the activity of glucoamylase, thus reducing citric acid production. When 130 U/g glucoamylase was added before fermentation, citric acid production was 141.5 g/L, which was even higher than the control (140.4 g/L). This process could completely eliminate extraction wastewater discharge and reduce water resource consumption.

  11. Integrated sample-to-detection chip for nucleic acid test assays.

    Science.gov (United States)

    Prakash, R; Pabbaraju, K; Wong, S; Tellier, R; Kaler, K V I S

    2016-06-01

    Nucleic acid based diagnostic techniques are routinely used for the detection of infectious agents. Most of these assays rely on nucleic acid extraction platforms for the extraction and purification of nucleic acids and a separate real-time PCR platform for quantitative nucleic acid amplification tests (NATs). Several microfluidic lab on chip (LOC) technologies have been developed, where mechanical and chemical methods are used for the extraction and purification of nucleic acids. Microfluidic technologies have also been effectively utilized for chip based real-time PCR assays. However, there are few examples of microfluidic systems which have successfully integrated these two key processes. In this study, we have implemented an electro-actuation based LOC micro-device that leverages multi-frequency actuation of samples and reagents droplets for chip based nucleic acid extraction and real-time, reverse transcription (RT) PCR (qRT-PCR) amplification from clinical samples. Our prototype micro-device combines chemical lysis with electric field assisted isolation of nucleic acid in a four channel parallel processing scheme. Furthermore, a four channel parallel qRT-PCR amplification and detection assay is integrated to deliver the sample-to-detection NAT chip. The NAT chip combines dielectrophoresis and electrostatic/electrowetting actuation methods with resistive micro-heaters and temperature sensors to perform chip based integrated NATs. The two chip modules have been validated using different panels of clinical samples and their performance compared with standard platforms. This study has established that our integrated NAT chip system has a sensitivity and specificity comparable to that of the standard platforms while providing up to 10 fold reduction in sample/reagent volumes.

  12. Optimisation of pressurised liquid extraction for elimination of sulphur interferences during determination of organotin compounds in sulphur-rich sediments by gas chromatography with flame photometric detection.

    Science.gov (United States)

    Wasik, Andrzej; Radke, Barbara; Bolałek, Jerzy; Namieśnik, Jacek

    2007-05-01

    A simple method for species-selective analysis of organotin compounds (OTCs) (butyl and phenyl) in sediments was developed. The sample preparation procedure was specifically optimised for sulphur-rich sediments to eliminate interferences from elemental sulphur and organosulphur compounds. Tin species were extracted from sediment samples using pressurised liquid extraction technique (PLE), ethylated - with simultaneous extraction to isooctane - in aqueous phase with sodium tetraethylborate (NaBEt(4)) and separated/detected by gas chromatography with flame photometric detection (GC-FPD). PLE operational variables (extraction temperature and pressure, solvent composition and number of static extraction steps) and extract handling routine were fine-tuned to minimise the amount of extracted interferents while keeping OTCs recovery at an acceptable level. Best results were obtained after extraction of sediment samples with methanol/water (75% v/v methanol) solution of acetic acid/sodium acetate with tropolone addition (0.6 g l(-1)). Derivatisation of low temperature, high-pressure (50 degrees C, 13.8 MPa) extracts gives isooctane extracts which are clean enough to be directly analysed by GC-FPD without any further cleanup. Interferences from elemental sulphur were completely eliminated while concentrations of other interferents were reduced to the level not impairing quantitation of OTCs under the study. No negative effects in terms of chromatographic column deterioration were observed after repeated injections of such extracts. Two certified reference materials, BCR646 and PACS-2, were analysed to assess performance of the method. Recoveries of all OTCs under the study, except MBT, were in the range of 91-114%. MBT extraction efficiency was low (34-47%) therefore the method is unsuitable for precise determinations of this compound.

  13. Effects of cold stratification, sulphuric acid, submersion in hot and ...

    African Journals Online (AJOL)

    STORAGESEVER

    2009-07-06

    Jul 6, 2009 ... Artvin Coruh University, Faculty of Forestry, 08000 Artvin, Turkey. Accepted 11 May ... deciduous shrubs and small trees with a distribution rang- ing from the ... temperate climates primarily for ornamental purposes. (Rudolf ...

  14. Acid-base titration curves in an integrated computer learning environment

    NARCIS (Netherlands)

    Heck, A.; Kędzierska, E.; Rodgers, L.; Chmurska, M.

    2008-01-01

    The topic of acid-base reactions is a regular component of many chemistry curricula that requires integrated understanding of various areas of introductory chemistry. Many students have considerable difficulties understanding the concepts and processes involved. It has been suggested and confirmed b

  15. Integration of galacturonic acid extraction with alkaline protein extraction from green tea leaf residue

    NARCIS (Netherlands)

    Zhang, Chen; Bozileva, Elvira; Klis, van der Frits; Dong, Yiyuan; Sanders, Johan P.M.; Bruins, Marieke E.

    2016-01-01

    Leaf pectin can be used as a feedstock for galacturonic acid (GA) production, but high extraction costs limit economic feasibility. To improve the extraction efficiency, leaf pectin extraction was integrated with an already cost-effective alkaline protein extraction, focusing on high yield of GA

  16. Effect of humic acids on electricity generation integrated with xylose degradation in microbial fuel cells

    DEFF Research Database (Denmark)

    Huang, Liping; Angelidaki, Irini

    2008-01-01

    Pentose and humic acids (HA) are the main components of hydrolysates, the liquid fraction produced during thermohydrolysis of lignocellulosic material. Electricity generation integrated with xylose (typical pentose) degradation as well as the effect of HA on electricity production in microbial fu...

  17. Dietary unsaturated fatty acids affect the mammary gland integrity and health in lactating dairy cows

    NARCIS (Netherlands)

    Mach Casellas, N.; Baal, van J.; Kruijt, L.; Jacobs, A.A.A.; Smits, M.A.

    2011-01-01

    Background Information about the effects of unsaturated fatty acids (UFA) supplementation on the health and integrity of the mammary gland in lactating dairy cows is lacking. Therefore, the aim of this study was to determine the effects of unprotected dietary UFA on the global expression pattern of

  18. Esophageal acid sensitivity and mucosal integrity in patients with functional heartburn.

    Science.gov (United States)

    Weijenborg, P W; Smout, A J P M; Bredenoord, A J

    2016-11-01

    Patients with functional heartburn (FH) experience troublesome heartburn that is not related to gastroesophageal reflux. The etiology of the heartburn sensation in FH patients is unknown. In patients with reflux disease, esophageal hypersensitivity seems associated with impaired mucosal integrity. We aimed to determine esophageal sensitivity and mucosal integrity in FH and non-erosive reflux disease (NERD) patients. In this prospective experimental study, we performed an acid perfusion test and upper endoscopy with biopsies in 12 patients with NERD and nine patients with FH. Mucosal integrity was measured during endoscopy using electrical tissue impedance spectroscopy and biopsy specimens were analyzed in Ussing chambers for transepithelial electrical resistance and transepithelial permeability. Lag time to heartburn perception was significantly longer in FH patients (median 12 min) than in NERD patients (median 3 min). Once perceived, intensity of heartburn was scored equal with median visual analog scale 6.5 and 7.1 respectively. Esophageal mucosal integrity was also comparable between FH and NERD patients, both in vivo extracellular impedance and ex vivo transepithelial resistance and permeability were similar. Patients with FH did not show acid hypersensitivity as seen in patients with NERD. However, once perceived, intensity of heartburn is similar. Esophageal mucosal integrity is similar between NERD and FH patients, and is therefore unlikely to be the underlying cause of the observed difference in esophageal acid perception. © 2016 John Wiley & Sons Ltd.

  19. Sulphur poisoning and regeneration of precious metal catalysed methane combustion

    Energy Technology Data Exchange (ETDEWEB)

    Jones, J.M.; Dupont, V.A.; Fullerton, D.J.; Ross, A.B.; Westwood, A.V.K. [Department of Fuel and Energy, SPEME, University of Leeds, Leeds LS2 9JT (United Kingdom); Brydson, R. [Department of Materials, SPEME, University of Leeds, Leeds LS2 9JT (United Kingdom); Nasri, N.S. [Gas Engineering Department, Universiti Teknologi Malaysia, 81310 Skudai Johor (Malaysia)

    2003-07-01

    In many of the applications of catalytic combustion small amounts of sulphur compounds are present in the feed gas. In the case of natural gas combustion, and solid fuel syngas, the sulphur compounds are in reduced forms. The present work investigates the influence of small quantities of reduced sulphur compounds on the combustion of methane over alumina-supported precious metal catalysts. The kinetics of the methane combustion in the presence of low concentrations of a mixture of sulphur compounds (ethyl mercaptan, methyl mercaptan, carbonyl sulphide and hydrogen sulphide) are compared with those in the absence of sulphur compounds. The ease of regeneration of the poisoned catalysts, via low temperature reduction with hydrogen, is also examined. In the conditions studied all catalysts have reduced activity in the presence of the sulphur-based gas mixture, but Pt/Al{sub 2}O{sub 3} and Rh/Al{sub 2}O{sub 3} are more strongly poisoned than Pd/Al{sub 2}O{sub 3}. Qualitative studies using gas chromatography with atomic emission detection of the exhaust gases, and FTIR spectroscopy of the spent Rh/Al{sub 2}O{sub 3} catalyst, suggest that the catalysts experience a mixture of reduced and oxidised species under reaction conditions, and that sulphating of the support occurs. The regeneration step facilitates metal mobility and meets with varying success depending upon the metal. Pt/Al{sub 2}O{sub 3} in particular is difficult to regenerate by reduction in hydrogen (400C for 0.5h), and agglomeration is observed by TEM. Rh/Al{sub 2}O{sub 3} regenerates well, and low metal particle size is maintained. A non-linear deactivation model is tested to separate sulphur-induced deactivation from 'natural' deactivation in the reaction mixture and preliminary results are presented.

  20. Sample to answer: a fully integrated nucleic acid identification system for bacteria monitoring

    Science.gov (United States)

    Kim, Jungkyu; Elsnab, John; Johnson, Michael; Gale, Bruce K.

    2010-02-01

    A fully integrated microfluidic system was developed and incorporates an EC-MWCNT (electrochemical multiwalled carbon nanotube) sensor for the detection of bacteria. Sample metering, reagent metering and delivery was implemented with microvalves and pumps embedded inside the microfluidic system. The nucleic acid extraction was performed using microchannels controlled using automated platforms and a disposable microfluidic silica cartridge. The target samples were flowed and hybridized with probe ssDNA (single strand DNA) across the MWCNT-EC sensor (built on a silicon chip), which was embedded in a microfluidic cell. The 9-pad sensor was scanned before and after hybridization to measure the quantity of RNA (Ribonucleic acid) bound to the array surface. A rapid and accurate sample-in answer-out nucleic acid system was realized with automated volume metering, microfluidic sample preparation, and integrated nano-biosensors.

  1. The direct determination of the forms of sulphur in coal using microwave digestion and i.c.p.-a.e.s. analysis

    Energy Technology Data Exchange (ETDEWEB)

    Laban, K.L.; Atkin, B.P. [University of Nottingham, Nottingham (United Kingdom). School of Chemical, Environmental and Mining Engineering

    2000-01-01

    A sequential digestion method is reported for the direct determination of sulphate, pyrite and organic sulphur concentrations in coals of either bituminous or sub-bituminous rank. A three stage extraction was developed, using acid digestion in a microwave oven. In the first stage, 5 M HCl is used to dissolve sulphate phases in the coal. Pyrite is then extracted from the stage 1 residue using 2 M HNO{sub 3}. The final stage, for the determination of organic sulphur, involves the use of concentrated HNO{sub 3}, HCl, HF and boric acid for the complete decomposition of residue that remains following stage 2. The extract solutions from each stage are rapidly analysed for sulphur using i.c.p.-a.e.s. The sums of the three forms of sulphur have shown consistent agreement with certified total sulphur data for most of the coals studied. This correlation, in addition to the good precision achieved by this technique, suggests that the sequential digestion method is reliable. Furthermore, significant timesavings are achievable over some of the standard techniques demonstrating the suitability of the method for routine analyses. 12 refs., 1 fig., 8 tabs.

  2. Leaching of a Cu-Co ore from Congo using sulphuric acidhydrogen peroxide leachants

    Directory of Open Access Journals (Sweden)

    Seo S.Y.

    2013-01-01

    Full Text Available A Cu-Co ore from Katinga Province, the Republic of Congo containing 1.5% Co and 1.6% Cu was tested to determine the leachability of Cu and Co using sulphuric acid and hydrogen peroxide mixtures at different conditions. Without hydrogen peroxide, the maximum extraction of copper and cobalt were found to be ~80% and ~15%, respectively when the acid concentration was varied between 0.36 - 1.1M. When hydrogen peroxide was added (0.008-0.042M, Cu recovery was enhanced to ~90%. Recoveries of ~90% of Co could be achieved at 20ºC, using leachants consisting of 0.36M sulphuric acid and 0.025M hydrogen peroxide after 3 hours. The reaction time to reach 90% Co extraction was reduced to less than 2 hours at 30ºC. Stabcal modelling of the Eh-pH diagrams shows the importance of hydrogen peroxide as a reductant. The decrease of solution potential (300-350 mV by adding hydrogen peroxide was confirmed by Eh measurements during the tests. The leaching follows the shrinking core model kinetics, where the rate constant is linearly dependent on hydrogen peroxide concentration in the range 0-0.025M and proportional to (1/r2 where r is the average radius of the mineral particles. The activation energy for the leaching process is 72.3 kJ/mol.

  3. Electrochemical behavior of diverse vanadium ions at modified graphite felt electrode in sulphuric solution

    Institute of Scientific and Technical Information of China (English)

    LI Xiao-gang; HUANG Ke-long; LIU Su-qin; CHEN Li-quan

    2007-01-01

    PAN-based graphite feIt (PGF)treated in 98% sulphuric acid for 5 h and then kept at 450 ℃ for 2 h was evaluated for their electrochemical performance as electrodes of vanadium redox battery(VRB). Structure and characteristic of treated PAN-based graphite felt(TPGF) were determined by means of Fourier Transform Infrared Spectroscopy,Scanning Electron Microscopy, Brunauer-Einlrlett-Teller surface area analysis and VRB test system.The results show that the acid and heat synergistic effect increase the number of-COOH functional groups on the PGF surface. and the PGF is eroded by sulphuric acid oxidation.resulting in the surface area increases from 0.31 m2/g to 0.45 m2/g.The V(Ⅱ)/V(Ⅲ)redox reaction is electrochemically reversible on the TPGF electrode, while the V(Ⅳ)/V(Ⅴ)couple is a quasi reversible process.The diflusion coeffcients of the oxidation for V(Ⅳ)/V(Ⅴ)obtained from the scope of peak current Ip vs scan rate v1/2 is 4.4x10-5cm2/s. The improvement of electrochemical activity for the electrode is mainly ascribed to the increase of the number of-C00H groups on the TPGF,which behaves as active sites catalyzing the vanadium species reactions and accelerating electron transfer reaction and oxygen transfer.

  4. An optimized probucol microencapsulated formulation integrating a secondary bile acid (deoxycholic acid as a permeation enhancer

    Directory of Open Access Journals (Sweden)

    Mooranian A

    2014-09-01

    Full Text Available Armin Mooranian,1 Rebecca Negrulj,1 Nigel Chen-Tan,2 Gerald F Watts,3 Frank Arfuso,4 Hani Al-Salami11Biotechnology and Drug Development Research Laboratory, School of Pharmacy, Curtin Health Innovation Research Institute, Biosciences Research Precinct, Curtin University, 2Faculty of Science and Engineering, Curtin University, 3School of Medicine and Pharmacology, Royal Perth Hospital, University of Western Australia, 4School of Biomedical Science, Curtin Health Innovation Research Institute, Biosciences Research Precinct, Curtin University, Perth, AustraliaAbstract: The authors have previously designed, developed, and characterized a novel microencapsulated formulation as a platform for the targeted delivery of therapeutics in an animal model of type 2 diabetes, using the drug probucol (PB. The aim of this study was to optimize PB microcapsules by incorporating the bile acid deoxycholic acid (DCA, which has good permeation-enhancing properties, and to examine its effect on microcapsules’ morphology, rheology, structural and surface characteristics, and excipients’ chemical and thermal compatibilities. Microencapsulation was carried out using a BÜCHI-based microencapsulating system established in the authors’ laboratory. Using the polymer sodium alginate (SA, two microencapsulated formulations were prepared: PB-SA (control and PB-DCA-SA (test at a constant ratio (1:30 and 1:3:30, respectively. Complete characterization of the microcapsules was carried out. The incorporation of DCA resulted in better structural and surface characteristics, uniform morphology, and stable chemical and thermal profiles, while size and rheological parameters remained similar to control. In addition, PB-DCA-SA microcapsules showed good excipients’ compatibilities, which were supported by data from differential scanning calorimetry, Fourier transform infrared spectroscopy, scanning electron microscopy, and energy dispersive X-ray studies, suggesting

  5. Contributions to late Archaean sulphur cycling by life on land

    Science.gov (United States)

    Stüeken, Eva E.; Catling, David C.; Buick, Roger

    2012-10-01

    Evidence in palaeosols suggests that life on land dates back to at least 2.76Gyr ago. However, the biogeochemical effects of Archaean terrestrial life are thought to have been limited, owing to the lack of a protective ozone shield from ultraviolet radiation for terrestrial organisms before the rise of atmospheric oxygen levels several hundred million years later. Records of chromium delivery from the continents suggest that microbial mineral oxidation began at least 2.48Gyr ago but do not indicate when the terrestrial biosphere began to dominate important biogeochemical cycles. Here we combine marine sulphur abundance data with a mass balance model of the sulphur cycle to estimate the effects of the Archaean and early Proterozoic terrestrial biosphere on sulphur cycling. We find that terrestrial oxidation of pyrite by microbes using oxygen has contributed a substantial fraction of the total sulphur weathering flux since at least 2.5Gyr ago, with probable evidence of such activity 2.7-2.8Gyr ago. The late Archaean onset of terrestrial sulphur cycling is supported by marine molybdenum abundance data and coincides with a shift to more sulphidic ocean conditions. We infer that significant microbial land colonization began by 2.7-2.8Gyr ago. Our identification of pyrite oxidation at this time provides further support for the appearance of molecular oxygen several hundred million years before the Great Oxidation Event.

  6. Modelling the sulphur chemistry evolution in Orion KL

    CERN Document Server

    Esplugues, G B; Goicoechea, J R; Cernicharo, J

    2014-01-01

    We study the sulphur chemistry evolution in the Orion KL along the gas and grain phases of the cloud. We investigate the processes that dominate the sulphur chemistry and to determine how physical and chemical parameters, such as the final star mass and the initial elemental abundances, influence the evolution of the hot core and of the surrounding outflows and shocked gas (the plateau). We independently modelled the chemistry evolution of both components using the time-dependent gas-grain model UCL_CHEM and considering two different phase calculations. Phase I starts with the collapsing cloud and the depletion of atoms and molecules onto grain surfaces. Phase II starts when a central protostar is formed and the evaporation from grains takes place. We show how the gas density, the gas depletion efficiency, the initial sulphur abundance, the shocked gas temperature and the different chemical paths on the grains leading to different reservoirs of sulphur on the mantles affect sulphur-bearing molecules at differ...

  7. Surface EXAFS of Sulphur on Nickel.

    Science.gov (United States)

    Brennan, Sean Micheal

    The structural determination of adsorption geometries on surfaces has been limited to low-energy electron diffraction (LEED), photoelectron diffraction (PD), ion scattering, and surface extended x-ray absorption fine structure (SEXAFS). SEXAFS has the advantage that it can be analyzed without depending on calculated phase shifts, and does not require long range order on the surface. However, in the past SEXAFS measurements have often suffered from signal-to-noise problems which have limited the inherent high accuracy of the technique for structure determinations. Here are presented SEXAFS results on the low-Z adsorbate sulphur on Ni(100) which exhibit bulklike signal-to-noise ratios and allow the precise determination of the chemisorption site and adsorbate near -neighbor distances. The c(2x2) S on Ni(100) system was chosen because it has been studied extensively by other techniques and the relative merits of SEXAFS could be best demonstrated. The S-Ni first-nearest-neighbor distance was found to be 2.23 (+OR-) 0.02A, the accuracy being limited only by the EXAFS technique itself. For normal x-ray incidence the second-nearest-neighbor distance to Ni atoms in the (100) surface plane is clearly observed, and its distance of 4.15 (+OR-) 0.10A determines the adsorption site to be the fourfold hollow. This site is independently confirmed from analysis of the polarization-dependent nearest-neighbor SEXAFS amplitudes (relative amplitude ratios) and thirdly from determination of the absolute S coordination number on the surface by comparison with a bulk NiS standard. This variety of site-determination techniques will become even more important for the study of disordered surfaces, where the choice of adsorption sites is not restricted by the long range symmetry of the surface. When compared to the results obtained by the other available surface structural techniques it becomes clear that SEXAFS is the technique of choice for the determination of adsorbates on surfaces.

  8. Integrated printed circuit board device for cell lysis and nucleic acid extraction.

    Science.gov (United States)

    Marshall, Lewis A; Wu, Liang Li; Babikian, Sarkis; Bachman, Mark; Santiago, Juan G

    2012-11-01

    Preparation of raw, untreated biological samples remains a major challenge in microfluidics. We present a novel microfluidic device based on the integration of printed circuit boards and an isotachophoresis assay for sample preparation of nucleic acids from biological samples. The device has integrated resistive heaters and temperature sensors as well as a 70 μm × 300 μm × 3.7 cm microfluidic channel connecting two 15 μL reservoirs. We demonstrated this device by extracting pathogenic nucleic acids from 1 μL dispensed volume of whole blood spiked with Plasmodium falciparum. We dispensed whole blood directly onto an on-chip reservoir, and the system's integrated heaters simultaneously lysed and mixed the sample. We used isotachophoresis to extract the nucleic acids into a secondary buffer via isotachophoresis. We analyzed the convective mixing action with micro particle image velocimetry (micro-PIV) and verified the purity and amount of extracted nucleic acids using off-chip quantitative polymerase chain reaction (PCR). We achieved a clinically relevant limit of detection of 500 parasites per microliter. The system has no moving parts, and the process is potentially compatible with a wide range of on-chip hybridization or amplification assays.

  9. Predicting sulphur and nitrogen deposition using a simple statistical method

    Science.gov (United States)

    Oulehle, Filip; Kopáček, Jiří; Chuman, Tomáš; Černohous, Vladimír; Hůnová, Iva; Hruška, Jakub; Krám, Pavel; Lachmanová, Zora; Navrátil, Tomáš; Štěpánek, Petr; Tesař, Miroslav; Evans, Christopher D.

    2016-09-01

    Data from 32 long-term (1994-2012) monitoring sites were used to assess temporal development and spatial variability of sulphur (S) and inorganic nitrogen (N) concentrations in bulk precipitation, and S in throughfall, for the Czech Republic. Despite large variance in absolute S and N concentration/deposition among sites, temporal coherence using standardised data (Z score) was demonstrated. Overall significant declines of SO4 concentration in bulk and throughfall precipitation, as well as NO3 and NH4 concentration in bulk precipitation, were observed. Median Z score values of bulk SO4, NO3 and NH4 and throughfall SO4 derived from observations and the respective emission rates of SO2, NOx and NH3 in the Czech Republic and Slovakia showed highly significant (p Z score values were calculated for the whole period 1900-2012 and then back-transformed to give estimates of concentration for the individual sites. Uncertainty associated with the concentration calculations was estimated as 20% for SO4 bulk precipitation, 22% for throughfall SO4, 18% for bulk NO3 and 28% for bulk NH4. The application of the method suggested that it is effective in the long-term reconstruction and prediction of S and N deposition at a variety of sites. Multiple regression modelling was used to extrapolate site characteristics (mean precipitation chemistry and its standard deviation) from monitored to unmonitored sites. Spatially distributed temporal development of S and N depositions were calculated since 1900. The method allows spatio-temporal estimation of the acid deposition in regions with extensive monitoring of precipitation chemistry.

  10. The detection of sulphur in contamination spots in electron probe X-ray microanalysis

    Science.gov (United States)

    Adler, I.; Dwornik, E.J.; Rose, H.J.

    1962-01-01

    Sulphur has been identified as one of the elements present in the contamination spot which forms under the electron beam in the microprobe. The presence of the sulphur results in a rapid change in intensity measurements causing a loss of observed intensity for elements other than sulphur. The source of sulphur has been traced at least in part to the Apiezon B diffusion pump oil. A comparative X-ray fluorescence study of the Apiezon B and Octoil diffusion pump oils showed substantial amounts of sulphur in the Apiezon B. The Octoil was relatively free of sulphur.

  11. Analytical protocols for the determination of sulphur compounds characteristic of the metabolism of Chlorobium limicola

    Directory of Open Access Journals (Sweden)

    A. Aliboni

    2015-09-01

    Full Text Available Chlorobium limicola belongs to the green sulphur bacteria that has a potential for technological applications such as biogas clean up oxidising hydrogen sulphide to elemental sulphur through photosynthetic process. In the present work, analytical methods are described for the determination of different sulphur species in C. limicola cultures – sulphide by GC-FPD, sulphate by ionic HPLC and elemental sulphur by RP HPLC. The latter method eliminates the need for chloroform extraction of water suspensions of elemental sulphur. Data from sulphide and elemental sulphur analyses have been compared with ones coming from more traditional analytical methodologies.

  12. Exigências de aminoácidos sulfurados digestíveis para suínos machos castrados, mantidos em ambiente de alta temperatura dos 15 aos 30 kg Sulphurous amino acid requirements for barrows on high temperature environment from 15 to 30 kg

    Directory of Open Access Journals (Sweden)

    Roberta Gomes Marçal Vieira Vaz

    2005-10-01

    Full Text Available Para determinar a exigência de aminoácidos sulfurados de suínos machos castrados, dos 15 aos 30 kg, mantidos em ambiente de alta temperatura, foram utilizados 60 leitões mestiços (Landrace x Large White, com peso inicial de 14,97 ± 0,33 kg e idade de 50,36 ± 3,29 dias. Os animais foram distribuídos em delineamento experimental de blocos ao acaso, com cinco tratamentos (0,465; 0,511; 0,558; 0,605 e 0,652% de metionina + cistina digestível, seis repetições e dois animais por unidade experimental. As rações experimentais e a água foram fornecidas à vontade até o final do experimento, quando os animais atingiram o peso de 29,87 ± 0,52 kg. A temperatura no interior da sala foi mantida em 30,9 ± 0,7ºC e a umidade relativa em 67,5 ± 7,2%. O índice de temperatura de globo e umidade calculado no período foi de 81,2 ± 1,2. Os níveis de metionina + cistina digestível da ração influenciaram o ganho de peso diário, que aumentou, e a conversão alimentar, que reduziu de forma linear. Não se observou efeito dos tratamentos sobre o consumo de ração diário. Com relação às deposições de proteína (DP e de gordura (DG na carcaça, verificou-se efeito quadrático dos tratamentos sobre a DG, que reduziu até o nível de 0,508%, e efeito linear crescente sobre a DP. Concluiu-se que a exigência de aminoácidos sulfurados digestíveis para suínos machos castrados, mantidos em ambiente de alta temperatura, dos 15 aos 30 kg, é de 0,558% de metionina + cistina digestível na ração, que corresponde à relação metionina + cistina digestível:lisina digestível de 60%.Sixty swine (Landrace x Large White with initial weight of 14.97 ± 0.33 kg and 50.36 ± 3.29 days old were allotted to a blocks randomized experimental design, with five treatments (0.465, 0.511, 0.558, 0.605, and 0.652% digestible methionine + and cystineand six replicates of two animals, to determine the sulphurous amino acids requirements for barrows on a high

  13. Integrated production of cellulosic bioethanol and succinic acid from industrial hemp in a biorefinery concept.

    Science.gov (United States)

    Kuglarz, Mariusz; Alvarado-Morales, Merlin; Karakashev, Dimitar; Angelidaki, Irini

    2016-01-01

    The aim of this study was to develop integrated biofuel (cellulosic bioethanol) and biochemical (succinic acid) production from industrial hemp (Cannabis sativa L.) in a biorefinery concept. Two types of pretreatments were studied (dilute-acid and alkaline oxidative method). High cellulose recovery (>95%) as well as significant hemicelluloses solubilization (49-59%) after acid-based method and lignin solubilization (35-41%) after alkaline H2O2 method were registered. Alkaline pretreatment showed to be superior over the acid-based method with respect to the rate of enzymatic hydrolysis and ethanol productivity. With respect to succinic acid production, the highest productivity was obtained after liquid fraction fermentation originated from steam treatment with 1.5% of acid. The mass balance calculations clearly showed that 149kg of EtOH and 115kg of succinic acid can be obtained per 1ton of dry hemp. Results obtained in this study clearly document the potential of industrial hemp for a biorefinery. Copyright © 2015 Elsevier Ltd. All rights reserved.

  14. Overview of the Benefits and Costs og Integrating Heterogeneous Applications by Using Relaxed ACID Properties

    DEFF Research Database (Denmark)

    Frank, Lars

    2012-01-01

    In central databases the consistency of data is normally implemented by using the ACID (Atomicity, Consistency, Isolation and Durability) properties of a DBMS (Data Base Management System). In practice, it is not possible to implement the ACID properties if heterogeneous or distributed databases ...... functions of the company. The objective of this paper is to give an overview of both the benefits and costs of using application/database integration with relaxed ACID properties.......In central databases the consistency of data is normally implemented by using the ACID (Atomicity, Consistency, Isolation and Durability) properties of a DBMS (Data Base Management System). In practice, it is not possible to implement the ACID properties if heterogeneous or distributed databases...... are involved and the availability of data also has to be optimized. The objective of relaxed ACID properties across different database systems is that the users can trust the data they use even if the databases involved are temporarily inconsistent. Therefore, we will in this paper use relaxed ACID properties...

  15. Distributions of sulphur and other elements in human hair follicles

    Energy Technology Data Exchange (ETDEWEB)

    Ollerhead, R.W.; Legge, G.J.F.; Jones, L.N.

    1989-04-01

    Distributions of sulphur and other elements have been measured in several different specimens of human hair follicles. Whole specimens, longitudinal bisections, and 10 /mu/m thick longitudinal sections have been analyzed by PIXE using the Melbourne scanning proton microprobe. Elemental maps consistently showed that sulphur contents of the presumptive hair shaft (PHS) were uniformly low from 0 to 400 /mu/m (bulb end), increased continuously from about 400 to 800 /mu/m, and reached a plateau. Sulphur levels were uniformly low in the inner rooth sheath. These observations are consistent with previous protein analysis of PHS sections, indicating sequential synthesis of the major classes of keratin proteins. Maps of other elements indicated that Si, Ca, and Fe tended to be concentrated randomly, whereas, P, Cl, K, and Zn were more uniformly distributed. Average relative concentrations of Si, P, Cl, K, Ca, Fe, Cu, and Zn were estimated from total X-ray spectra. (orig.).

  16. Integrated production of lignin containing cellulose nanocrystals (LCNC) and nanofibrils (LCNF) using an easily recyclable di-carboxylic acid

    Science.gov (United States)

    Huiyang Bian; Liheng Chen; Hongqi Dai; J.Y. Zhu

    2017-01-01

    Here we demonstrate di-carboxylic acid hydrolysis for the integrated production of lignin containing cellulose nanocrystals (LCNC) and nanofibrils (LCNF) using two unbleached hardwood chemical pulps of lignin contents of 3.9 and 17.2%. Acid hydrolysis experiments used maleic acid solution of 60 wt% concentration at 120°C for 120 min under ambient pressure. Yields of...

  17. Serum Metabolomic Profiling of Sulphur Mustard-Exposed Individuals Using (1)H Nuclear Magnetic Resonance Spectroscopy.

    Science.gov (United States)

    Zamani, Zahra; Ghanei, Mostafa; Panahi, Yunus; Arjmand, Mohammad; Sadeghi, Sedigheh; Mirkhani, Fatemeh; Parvin, Shahram; Salehi, Maryam; Sahebkar, Amirhossein; Vahabi, Farideh

    2016-01-01

    Sulphur mustard is an alkylating agent that reacts with different cellular components, causing acute and delayed complications that may remain for decades after exposure. This study aimed to identify differentially expressed metabolites between mustard-exposed individuals suffering from chronic complications compared with unexposed individuals as the control group. Serum samples were obtained from 15 mustard-exposed individuals and 15 apparently healthy unexposed individuals. Metabolomic profiling was performed using (1)H nuclear magnetic resonance spectroscopy, and analyses were carried out using Chenomex and MATLAB softwares. Metabolites were identified using Human Metabolome Database, and the main metabolic pathways were identified using MetaboAnalyst software. Chemometric analysis of serum samples identified 11 differentially expressed metabolites between mustard-exposed and unexposed groups. The main pathways that were influenced by sulphur mustard exposure were related to vitamin B6 (down-regulation), bile acid (up-regulation) and tryptophan (down-regulation) metabolism. Metabolism of vitamin B6, bile acids and tryptophan are the most severely impaired pathways in individuals suffering from chronic mustard-induced complications. These findings may find implications in the monitoring of exposed patients and identification of new therapeutic approaches.

  18. Removal of odorous sulphur compounds from industrial gases by biotrickling filters

    Directory of Open Access Journals (Sweden)

    Vincenzo Torretta

    2016-06-01

    Full Text Available A pilot plant for the treatment of Sulphur-based odorous gases was installed in a line of a phosphoric acid plant located in Skhira, Tunisia. The air pollution control system train consisted of a first stage, including a chemical scrubber operating with an alkaline solution containing caustic soda, followed by a two-stage biotrickling filter (BTF filled with Mytilus edulis shells. This study evaluated the performance of the dual-stage BTF in removing hydrogen sulphide (H2S, sulphur dioxide (SO2 and dimethyl sulphide (DMS from the phosphoric acid reactor's exhaust air current. Concentrations of H2S, SO2 and DMS at the inlet of the two-stage BTF were 10-30 ppm, < 1-20 ppm and 16-30 ppm, respectively. All of the respective concentrations at the outlet of the biological step were < 1 ppm, except for the H2S in the outlet during the first day of operation (10 ppm. Removal efficiencies were generally higher than 95% for all compounds, and remained high even with an increase of the off-gas flow rate. Mass-removal capacity was at least 2.0 g m-3 h-1, 0.5 g m-3 h-1 and 6.2 g m-3 h-1, for H2S, SO2 and DMS, respectively. The removal efficiencies of the process were satisfactory, especially considering the already low inlet concentrations, due to the high quality of the raw phosphate used.

  19. Integrated assessment of acid deposition impacts using reduced-form modeling. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Sinha, R.; Small, M.J.

    1996-05-01

    Emissions of sulfates and other acidic pollutants from anthropogenic sources result in the deposition of these acidic pollutants on the earth`s surface, downwind of the source. These pollutants reach surface waters, including streams and lakes, and acidify them, resulting in a change in the chemical composition of the surface water. Sometimes the water chemistry is sufficiently altered so that the lake can no longer support aquatic life. This document traces the efforts by many researchers to understand and quantify the effect of acid deposition on the water chemistry of populations of lakes, in particular the improvements to the MAGIC (Model of Acidification of Groundwater in Catchments) modeling effort, and describes its reduced-form representation in a decision and uncertainty analysis tool. Previous reduced-form approximations to the MAGIC model are discussed in detail, and their drawbacks are highlighted. An improved reduced-form model for acid neutralizing capacity is presented, which incorporates long-term depletion of the watershed acid neutralization fraction. In addition, improved fish biota models are incorporated in the integrated assessment model, which includes reduced-form models for other physical and chemical processes of acid deposition, as well as the resulting socio-economic and health related effects. The new reduced-form lake chemistry and fish biota models are applied to the Adirondacks region of New York.

  20. Simple spectrophotometric determination of sulphur ion in water samples%分光光度法测定水样中的硫离子

    Institute of Scientific and Technical Information of China (English)

    苏庆平

    2009-01-01

    A new simple spectrophotometric method was proposed for the determination sulphur ion in water samples.In the medium of 0.05 mol/L HCl,sulphur anion turns mixed acid of the silicon and molybdenum into molybdenum blue.Its absorption maxima was found at the wavelength of 700 such as the amount of reagent and reaction time were optimized,and the interferences from common aions were also investigated.This method was successfully used for the determination of sulfur in water samples.

  1. Dry deposition of sulphur on the Mpumalanga highveld: a pilot study using the inferential method

    CSIR Research Space (South Africa)

    Zunckel, M

    1996-10-01

    Full Text Available A pilot study which uses the inferential method to estimate dry deposition of sulphur on the central Mpumalanga highveld is discussed in this paper. Ambient concentrations of sulphur dioxide, particulates and micro-meteorological measurements from 2...

  2. Sulphur enrichment in a sediment core from the central western continental margin of India

    Digital Repository Service at National Institute of Oceanography (India)

    Rao, P.S.; Rao, Ch.M.

    Anomalous sulphur values in relation to organic carbon have been found in the sediments of a core collected from the central western continental margin of India. The relationship between organic carbon and sulphur is similar to that of the sediments...

  3. SULPHUR AVAILABILITY IN BRAZILIAM SOILS: RESPONSE TO SULPHUR FERTILIZING IN PRESENCE AND AUSENCE OF LIMING DISPONIBILIDADE DE ENXOFRE EM SOLOS BRASILEIROS: RESPOSTA À ADUBAÇÃO SULFATADA NA PRESENÇA E AUSÊNCIA DE CALAGEM

    Directory of Open Access Journals (Sweden)

    Eurípedes Malavolta

    2007-09-01

    Full Text Available

    A greenhouse experiment was carried out with surface samples of 12 soils from the States of São Paulo, Minas Gerais and Goiás (Brazil. Carbon (C content varied from 0.50 to 3.03%, sulphur from 0.0104 to 0.0319% and clay varied from 8 to 60%. Corn (Zea mays L. was grown in two successive croppings in presence of three rates of S (0, 20 and 40 ppm applied as gypsum, previously incubated in presence and absence of lime. Dry matter production did not show significant difference due to the two croppings of the soils; sulphur uptake, otherwise, was thoroughly lower in the second cropping, indicating the depletion of native and applied sulphur. Sandy soils have a lower supplying power of sulphur due to its effective small reserve. Clayey soils, moreover “cerrado” soils with higher carbon contents, possess greater croppings and sulphur uptake potentials, provided the soil acidity is neutralized. Liming, besides its role as soil acidity neutralizer and as calcium and magnesium supplier, showed positive interaction with sulphur and a synergistic effect on the depletion of soils native sulphur. The rates of sulphur which maximized dry matter yield and sulphur absorption varied in the range of 20 to 70 ppm, being the highest requirements found in clayey soils with no liming.

    Conduziu-se um experimento em casa de vegetação com amostras superficiais de 12 solos, provenientes dos Estados de São Paulo, Minas Gerais e Goiás (Brasil, com teores de carbono variando entre 0,5 e 3,03%, de enxofre total entre 0,0104 e 0,319% e de argila entre 8 e 60%. Os solos foram submetidos a dois cultivos sucessivos com milho (Zea mays L., com os tratamentos: 12 solos, 3 doses de gesso (0, 20 e 40 ppm de S, previamente incubados na ausência e presença de calagem. A produção de matéria seca da parte a

  4. Managing sulphur content of pig diet to control further sulphides production during pig slurry anaerobic storage

    OpenAIRE

    Peu, P.; Picard, S.; Dourmad, J.Y.; Dabert, P.

    2010-01-01

    International audience; The mixing of different raw materials during formulation strategies of pig feeding influences sulphurs food intake and further sulphur excretion by the animals. Increased amount of sulphur in manure can result in toxicity and odour problems during storage as well as potential inhibition problems in case of anaerobic digestion treatment. The objective of this study was to determine the behaviour of different sulphur feed contents on pig excretion via faeces and urine, t...

  5. Improving Escherichia coli membrane integrity and fatty acid production by expression tuning of FadL and OmpF.

    Science.gov (United States)

    Tan, Zaigao; Black, William; Yoon, Jong Moon; Shanks, Jacqueline V; Jarboe, Laura R

    2017-02-28

    Construction of microbial biocatalysts for the production of biorenewables at economically viable yields and titers is frequently hampered by product toxicity. Membrane damage is often deemed as the principal mechanism of this toxicity, particularly in regards to decreased membrane integrity. Previous studies have attempted to engineer the membrane with the goal of increasing membrane integrity. However, most of these works focused on engineering of phospholipids and efforts to identify membrane proteins that can be targeted to improve fatty acid production have been unsuccessful. Here we show that deletion of outer membrane protein ompF significantly increased membrane integrity, fatty acid tolerance and fatty acid production, possibly due to prevention of re-entry of short chain fatty acids. In contrast, deletion of fadL resulted in significantly decreased membrane integrity and fatty acid production. Consistently, increased expression of fadL remarkably increased membrane integrity and fatty acid tolerance while also increasing the final fatty acid titer. This 34% increase in the final fatty acid titer was possibly due to increased membrane lipid biosynthesis. Tuning of fadL expression showed that there is a positive relationship between fadL abundance and fatty acid production. Combinatorial deletion of ompF and increased expression of fadL were found to have an additive role in increasing membrane integrity, and was associated with a 53% increase the fatty acid titer, to 2.3 g/L. These results emphasize the importance of membrane proteins for maintaining membrane integrity and production of biorenewables, such as fatty acids, which expands the targets for membrane engineering.

  6. Sulphur Mustard Poisoning and Its Complications in Iranian Veterans

    Directory of Open Access Journals (Sweden)

    Beeta Balali-Mood

    2009-09-01

    Full Text Available Sulphur mustard is a chemical warfare agent, which was largelyused during the World War One and in Iraq-Iran conflict. It mayalso be used as a chemical terrorism agent. Therefore, medicalprofessions should have sufficient knowledge and be preparedfor medical intervention of any such chemical attack.Sulphur mustard exerts direct toxic effects on the eyes, skin,and respiratory tract, with subsequent systemic actions on thenervous, immunologic, hematologic, digestive, and reproductivesystems. It is an alkylating agent that affects DNA synthesis andthus, delayed complications have been considered since theWorld War One. Cases of malignancies in the target organs particularlyin hematopoietic, respiratory, and digestive systemswere reported. Common delayed respiratory complications includechronic bronchitis, bronchiectasis, frequent bronchopneumonia,and pulmonary fibrosis, all of which tend to deterioratewith time. Severe dry skin, delayed keratitis, and reduction ofnatural killer cells with subsequent increased risk of infectionsand malignancies are also among the most distressing long-termconsequences of sulphur mustard intoxication. However, despiteextensive research that has been conducted on Iranian veteransduring the past decades, major gaps continue to remain in thesulphur mustard literature. Immunological and neurological dysfunctionsand the relationship between exposure to sulphur mustardand mutagenicity, carcinogenicity, and teratogenicity areimportant fields that require further studies, particularly on Iranianveterans with chronic health problems caused by sulphurmustard poisoning. There is also a paucity of information on themedical management of acute and delayed toxic effects of sulphurmustard poisoning, a subject that greatly challenges themedical professions.

  7. Modelling Sulphur Clusters for an Understanding of Ultramarine

    African Journals Online (AJOL)

    and Møller-Plesset second order perturbation theory were applied to determine the .... noselite-like (nosean) phase.19 The high ratio of sulphur atoms to ..... Soc., Dalton Trans., 1990, 593–597. ... John Wiley & Sons, New York, 2002, pp.

  8. Sulphur-oxidising and Sulphate-reducing Communities in Brazilian Mangrove Sediments

    NARCIS (Netherlands)

    Dias, A.C.F; Fasanella, C.C.; Durrer, A.; Melo, I.S.; Kuramae, E.E.; Andreote, F.D.

    2014-01-01

    Mangrove soils are anaerobic environments rich in sulphate and organic matter. Although the sulphur cycle is one of the major actors in this ecosystem, little is known regarding the sulphur bacteria communities in mangrove soils. We investigated the abundance, composition and diversity of sulphur-ox

  9. Biostrategic Removal of Sulphur Contamination in Groundwater With Sulphur-Reducing Bacteria: A Review

    Directory of Open Access Journals (Sweden)

    Sandeep Satapathy

    2017-02-01

    Full Text Available The rapid growth in the use of fertilizers and pesticides in agriculture, excessive extraction of groundwater, and rise in the number of industries with inefficient waste disposal system have been some of the key factors in degradation of groundwater quality during the past years. Although groundwater is considered as a valuable natural resource, the quality control of this resource has systematically failed in India. Irrespective of rural or urban locations, the average sulphate contamination of groundwater in India has reached 90 to 150 mg/L. Such a borderline contamination concentration poses threat both to livelihood and to economy. In addition, the negative health effects of sulphate-contaminated drinking water can range from dermatitis to lung problems and skin cancer. The biostrategic manipulation of groundwater discussed in this article involves sulphate-reducing bacteria used in addition to a 3-step procedure involving constitutive aeration, filtration, and shock chlorination. With earlier use of a similar strategy in the United States and Europe proven to be beneficial, we propose a combinatorial and economical approach for processing of groundwater for removal of sulphur contamination, which still largely remains unnoticed and neglected.

  10. On the Galactic chemical evolution of sulphur. Sulphur abundances from the [S i] 1082 nm line in giants

    CERN Document Server

    Matrozis, E; Dupree, A K

    2013-01-01

    Context. The Galactic chemical evolution of sulphur is still under debate. At low metallicities some studies find no correlation between [S/Fe] and [Fe/H], others find [S/Fe] increasing towards lower metallicities, and still others find a combination of the two. Each scenario has different implications for the Galactic chemical evolution of sulphur. Aims. To contribute to the discussion on the Galactic chemical evolution of sulphur by deriving sulphur abundances from non-LTE insensitive spectral diagnostics in Disk and Halo stars with homogeneously determined stellar parameters. Methods. We derive Teff from photometric colours, logg from stellar isochrones and Bayesian estimation, and [Fe/H] and [S/Fe] from spectrum synthesis. We derive [S/Fe] from the [S i] 1082 nm line in 39 mostly cool and metal-poor giants, using 1D LTE MARCS model atmospheres to model our high-resolution NIR spectra obtained with the VLT, NOT and Gemini South telescopes. Results. We derive homogeneous stellar parameters for 29 stars. Our...

  11. Opportunity integrated assessment facilitating critical thinking and science process skills measurement on acid base matter

    Science.gov (United States)

    Sari, Anggi Ristiyana Puspita; Suyanta, LFX, Endang Widjajanti; Rohaeti, Eli

    2017-05-01

    Recognizing the importance of the development of critical thinking and science process skills, the instrument should give attention to the characteristics of chemistry. Therefore, constructing an accurate instrument for measuring those skills is important. However, the integrated instrument assessment is limited in number. The purpose of this study is to validate an integrated assessment instrument for measuring students' critical thinking and science process skills on acid base matter. The development model of the test instrument adapted McIntire model. The sample consisted of 392 second grade high school students in the academic year of 2015/2016 in Yogyakarta. Exploratory Factor Analysis (EFA) was conducted to explore construct validity, whereas content validity was substantiated by Aiken's formula. The result shows that the KMO test is 0.714 which indicates sufficient items for each factor and the Bartlett test is significant (a significance value of less than 0.05). Furthermore, content validity coefficient which is based on 8 experts is obtained at 0.85. The findings support the integrated assessment instrument to measure critical thinking and science process skills on acid base matter.

  12. Utilization of activated carbon loaded with sulphur for sulphur fertilization in agriculture; Verwertung von mit Schwefel beladener Aktivkohle als Schwefelduenger in der Landwirtschaft

    Energy Technology Data Exchange (ETDEWEB)

    Kirfel, Kristina; Hoffmann, Heide [Humboldt Univ. Berlin (Germany). AG Agraroekologie und Oekologischer Landbau

    2013-01-15

    Due to the decrease of atmospheric sulphur deposition, sulphur fertilization has gained significance for agriculture in recent years. Carbon-sulphur-pellets (CSP), activated carbon pellets loaded with sulphur, previously used for desulphurization in biogas plants, are up to now disposed of as waste. In this context the question arises if CSP could be of use for sulphur fertilization of agricultural crops. The objective of this study was to test sulphur release and plant availability from, and plant tolerance towards CSP. A pot experiment using Zea mays with different shares of CSP was carried out. Leaf green intensity of vital plants, indicating plants' current nutritional status, was measured and differences in plant development were documented regularly. At the end of the trial period biomass and elemental contents of the test plants, as well as electrical conductivity and pH-value of the substrate-CSP-mixtures were determined. Amendments of 0.2 m.-% to 1.0 m.-% had a positive effect on plants' dry mass yield; higher shares led to considerable yield losses. By addition of CSP, sulphur content in the plant dry mass increased compared to the control without sulphur fertilization. This result indicates that sulphur adsorbed to activated carbon becomes plant available when applicated to cultural substrate. (orig.)

  13. Cu{sub 2}ZnSnS{sub 4} absorber layers obtained through sulphurization of metallic precursors: Graphite box versus sulphur flux

    Energy Technology Data Exchange (ETDEWEB)

    Sousa, M.G., E-mail: martasousa@ua.pt [I3N and Departamento de Física, Universidade de Aveiro, Campus Universitário de Santiago, 3810-193 Aveiro (Portugal); Cunha, A.F. da [I3N and Departamento de Física, Universidade de Aveiro, Campus Universitário de Santiago, 3810-193 Aveiro (Portugal); Salomé, P.M.P. [Angstrom Solar Center, Solid State Electronics, Uppsala University, Angstrom Laboratory PO Box 534, SE-751 21 Uppsala (Sweden); Fernandes, P.A. [I3N and Departamento de Física, Universidade de Aveiro, Campus Universitário de Santiago, 3810-193 Aveiro (Portugal); Departamento de Física, Instituto Superior de Engenharia do Porto, Instituto Politécnico do Porto, Rua Dr. António Bernardino de Almeida, 431, 4200-072 Porto (Portugal); Teixeira, J.P.; Leitão, J.P. [I3N and Departamento de Física, Universidade de Aveiro, Campus Universitário de Santiago, 3810-193 Aveiro (Portugal)

    2013-05-01

    In this work we employed a hybrid method, combining RF-magnetron sputtering with evaporation, for the deposition of tailor made metallic precursors, with varying number of Zn/Sn/Cu (ZTC) periods and compared two approaches to sulphurization. Two series of samples with 1 ×, 2 × and 4 × ZTC periods have been prepared. One series of precursors was sulphurized in a tubular furnace directly exposed to a sulphur vapour and N{sub 2} + 5% H{sub 2} flux at a pressure of 5.0 × 10{sup +4} Pa. A second series of identical precursors was sulphurized in the same furnace but inside a graphite box where sulphur pellets have been evaporated again in the presence of N{sub 2} + 5% H{sub 2} and at the same pressure as for the sulphur flux experiments. The morphological and chemical analyses revealed a small grain structure but good average composition for all three films sulphurized in the graphite box. As for the three films sulphurized in sulphur flux grain growth was seen with the increase of the number of ZTC periods whilst, in terms of composition, they were slightly Zn poor. The films' crystal structure showed that Cu{sub 2}ZnSnS{sub 4} is the dominant phase. However, in the case of the sulphur flux films SnS{sub 2} was also detected. Photoluminescence spectroscopy studies showed an asymmetric broad band emission which occurs in the range of 1–1.5 eV. Clearly the radiative recombination efficiency is higher in the series of samples sulphurized in sulphur flux. We have found that sulphurization in sulphur flux leads to better film morphology than when the process is carried out in a graphite box in similar thermodynamic conditions. Solar cells have been prepared and characterized showing a correlation between improved film morphology and cell performance. The best cells achieved an efficiency of 2.4%. - Highlights: ► Precursors deposited by a hybrid method with n × zinc tin copper (ZTC) periods ► Achieved good reproducibility in the deposition of metallic

  14. A study of the electrochemical processes in lithium-sulphur cells by impedance spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Kolosnitsyn, V.S.; Kuzmina, E.V.; Karaseva, E.V.; Mochalov, S.E. [Institution of the Russian Academy of Sciences Institute of Organic Chemistry of Ufa Scientific Center of the Russian Academy of Sciences, Laboratory of Electrochemistry, 71, pr. Oktyabrya, Ufa, Bashkortostan, 450054 (Russian Federation)

    2011-02-01

    The changes in the properties of lithium-sulphur cell components (electrolyte, sulphur and lithium electrodes) during cycling are studied by AC impedance spectroscopy. It is shown that during the charge and discharge of lithium-sulphur cells the conductivity of the electrolyte is changed. We believe that the observed changes in the electrolyte conductivity can be explained by the formation of soluble lithium polysulphides by electrochemical reactions. The properties of the electrolyte significantly influence the rate of the electrochemical processes which occur both on the sulphur and lithium electrodes in lithium-sulphur cells. (author)

  15. WATER PINCH TECHNOLOGY APPLICATION TO MINIMIZE SULPHUROUS WASTEWATER IN AN OIL REFINERY

    Directory of Open Access Journals (Sweden)

    Gabriel Orlando Lobelles Sardiñas

    2017-01-01

    Full Text Available In oil refining industries there is a high water consumption, which influences the high production costs and impacts the environment due to the discharge of their wastes. It is known that there are no technological conditions for the reuse of industrial water at the oil refineries, based on hydroskimming processes. The objective of this study is to implement the process integration methodology, Water Pinch, to a sour water stripper unit, as a unitary process of an oil refinery, to minimize the amount of sulphurous waste water and reduce contamination of the bay that receives these wastes. The technology is applied to evaluate the volume of sulphurous wastewater generated in the Cienfuegos oil refinery. This technology allows identifying opportunities for recovery and reuse of water, based on concentration ranges of contaminants. To achieve this purpose, a sour water stripper tower was assessed with the help of Water Pinch software, which provided an optimized distribution network, as a proposed technological improvement. This facilitated to recover and reuse 667 757, 28 m3 of water per year, and 1 035 023, 78 CUC were saved, at the same time the amount of polluting effluents decreased in approximately 2 % of non-reusable treated water.

  16. Integrative device and process of oxidization, degassing, acidity adjustment of 1BP from APOR process

    Energy Technology Data Exchange (ETDEWEB)

    Zuo, Chen; Zheng, Weifang, E-mail: wfazh@ciae.ac.cn; Yan, Taihong; He, Hui; Li, Gaoliang; Chang, Shangwen; Li, Chuanbo; Yuan, Zhongwei

    2016-02-15

    Graphical abstract: Previous (left) and present (right) device of oxidation, degassing, acidity adjustment of 1BP. - Highlights: • We designed an integrative device and process. • The utilization efficiency of N{sub 2}O{sub 4} is increased significantly. • Our work results in considerable simplification of the device. • Process parameters are determined by experiments. - Abstract: Device and process of oxidization, degassing, acidity adjustment of 1BP (The Pu production feed from U/Pu separation section) from APOR process (Advanced Purex Process based on Organic Reductants) were improved through rational design and experiments. The device was simplified and the process parameters, such as feed position and flow ratio, were determined by experiments. Based on this new device and process, the reductants N,N-dimethylhydroxylamine (DMHAN) and methylhydrazine (MMH) in 1BP solution could be oxidized with much less N{sub 2}O{sub 4} consumption.

  17. An Integrative Analysis of the Effects of Auxin on Jasmonic Acid Biosynthesis in Arabidopsis thaliana

    Institute of Scientific and Technical Information of China (English)

    Jun Liu; Xiu-Jie Wang

    2006-01-01

    Auxin and jasmonic acid (JA) are two plant phytohormones that both participate in the regulation of many developmental processes. Jasmonic acid also plays important roles in plant stress response reactions.Although extensive investigations have been undertaken to study the biological functions of auxin and JA,little attention has been paid to the cross-talk between their regulated pathways. In the few available reports examining the effects of auxin on the expression of JA or JA-responsive genes, both synergetic and antagonistic results have been found. To further investigate the relationship between auxin and JA, we adopted an integrative method that combines microarray expression data with pathway information to study the behavior of the JA biosynthesis pathway under auxin treatment. Our results showed an overall downregulation of genes involved in JA biosynthesis, providing the first report of a relationship between auxin and the JA synthesis pathway in Arabidopsis seedlings.

  18. Establishment and assessment of an integrated citric acid-methane production process.

    Science.gov (United States)

    Xu, Jian; Chen, Yang-Qiu; Zhang, Hong-Jian; Bao, Jia-Wei; Tang, Lei; Wang, Ke; Zhang, Jian-Hua; Chen, Xu-Sheng; Mao, Zhong-Gui

    2015-01-01

    To solve the problem of extraction wastewater in citric acid industrial production, an improved integrated citric acid-methane production process was established in this study. Extraction wastewater was treated by anaerobic digestion and then the anaerobic digestion effluent (ADE) was stripped by air to remove ammonia. Followed by solid-liquid separation to remove metal ion precipitation, the supernatant was recycled for the next batch of citric acid fermentation, thus eliminating wastewater discharge and reducing water consumption. 130U/g glucoamylase was added to medium after inoculation and the recycling process performed for 10 batches. Fermentation time decreased by 20% in recycling and the average citric acid production (2nd-10th) was 145.9±3.4g/L, only 2.5% lower than that with tap water (149.6g/L). The average methane production was 292.3±25.1mL/g CODremoved and stable in operation. Excessive Na(+) concentration in ADE was confirmed to be the major challenge for the proposed process.

  19. Acid mine water neutralisation with ammonium hydroxide and ...

    African Journals Online (AJOL)

    2013-05-30

    May 30, 2013 ... Keywords: acid mine water, ammonium hydroxide, barium hydroxide, sulphate removal ... oxygen becomes oxidised to soluble iron and sulphuric acid, .... The effects of the following parameters on the Fe (II) oxidation.

  20. SULPHUR DIOXIDE LEACHING OF URANIUM CONTAINING MATERIAL

    Science.gov (United States)

    Thunaes, A.; Rabbits, F.T.; Hester, K.D.; Smith, H.W.

    1958-12-01

    A process is described for extracting uranlum from uranium containing material, such as a low grade pitchblende ore, or mill taillngs, where at least part of the uraniunn is in the +4 oxidation state. After comminuting and magnetically removing any entrained lron particles the general material is made up as an aqueous slurry containing added ferric and manganese salts and treated with sulfur dioxide and aeration to an extent sufficient to form a proportion of oxysulfur acids to give a pH of about 1 to 2 but insufficient to cause excessive removal of the sulfur dioxide gas. After separating from the solids, the leach solution is adjusted to a pH of about 1.25, then treated with metallic iron in the presence of a precipitant such as a soluble phosphate, arsonate, or fluoride.

  1. Cleaner production of citric acid by recycling its extraction wastewater treated with anaerobic digestion and electrodialysis in an integrated citric acid-methane production process.

    Science.gov (United States)

    Xu, Jian; Su, Xian-Feng; Bao, Jia-Wei; Chen, Yang-Qiu; Zhang, Hong-Jian; Tang, Lei; Wang, Ke; Zhang, Jian-Hua; Chen, Xu-Sheng; Mao, Zhong-Gui

    2015-01-01

    To solve the pollution problem of extraction wastewater in citric acid production, an integrated citric acid-methane production process was proposed. Extraction wastewater was treated through anaerobic digestion and the anaerobic digestion effluent (ADE) was recycled for the next batch of citric acid fermentation, thus eliminating wastewater discharge and reducing water consumption. Excessive Na(+) contained in ADE could significantly inhibit citric acid fermentation in recycling and was removed by electrodialysis in this paper. Electrodialysis performance was improved after pretreatment of ADE with air stripping and activated carbon adsorption to remove precipitable metal ions and pigments. Moreover, the concentrate water was recycled and mixed with feed to improve the water recovery rate above 95% in electrodialysis treatment, while the dilute water was collected for citric acid fermentation. The removal rate of Na(+) in ADE was above 95% and the citric acid production was even higher than that with tap water.

  2. Possible Superconductivity at 37 K in Graphite-Sulphur Composite

    Institute of Scientific and Technical Information of China (English)

    杨海朋; 闻海虎; 赵志文; 李世亮

    2001-01-01

    Sulphur intercalated graphite composites with diamagnetic transitions at 6.7 and 37K are prepared. The magnetization hysteresis loops (MHL), x-ray diffraction (XRD) patterns, and resistance have been measured. From the MHL, a slight superconducting-like penetration process is observed at 15K in the low field region. The XRD shows no large difference from the mixture of graphite and sulphur indicating that the volume of the superconducting phase (if any) is very small. The temperature dependence of resistance shows a typical semi-conducting behaviour with a saturation in the low-temperature region. This saturation is either induced by the delocalization of conducting electrons or by possible superconductivity in this system.

  3. Sulphur hexafluoride as a stripper gas for tandem accelerators

    Science.gov (United States)

    Hotchkis, M. A. C.; Child, D.; Fink, D.; Garton, D.; Levchenko, V.; Wilcken, K.

    2013-05-01

    We have investigated sulphur hexafluoride as a stripper gas in tandem accelerators by using the ANTARES accelerator system at ANSTO to measure charge state distributions for this gas. Results are reported at 4 MV terminal voltage for injected negative ions ranging from carbon to uranium oxide. For iodine and thorium the distributions are extended across a range of energies of practical use for accelerator mass spectrometry, ion beam analysis and other accelerator applications. Charge state distributions using sulphur hexafluoride are found to have mean charge states up to 1 charge unit higher than, and to be broader than, corresponding distributions for argon gas, except in the case of carbon beams. As a result, SF6 is shown to provide significantly higher yields for charge states of heavy ions above the mean charge state. We now perform actinide AMS measurements with 9% yield to the 5+ charge state, compared to 4-5% achieved previously with argon gas.

  4. Sulphur chemistry in the envelopes of massive young stars

    CERN Document Server

    Van der Tak, F F S; Braakman, R; Van Dishoeck, E F

    2003-01-01

    The sulphur chemistry in nine regions in the earliest stages of high-mass star formation is studied through single-dish submillimeter spectroscopy. The line profiles indicate that 10-50% of the SO and SO2 emission arises in high-velocity gas, either infalling or outflowing. For the low-velocity gas, excitation temperatures are 25 K for H2S, 50 K for SO, H2CS, NS and HCS+, and 100 K for OCS and SO2, indicating that most observed emission traces the outer parts (T100 K) of six sources, the SO2 abundance is enhanced by factors of ~100-1000. This region of hot, abundant SO2 has been seen before in infrared absorption, and must be small, ~ 100 K) gas, sulphur-bearing molecules cannot be used as evolutionary tracers during star formation.

  5. Sulphur deprivation limits Fe-deficiency responses in tomato plants.

    Science.gov (United States)

    Zuchi, Sabrina; Cesco, Stefano; Varanini, Zeno; Pinton, Roberto; Astolfi, Stefania

    2009-06-01

    The aim of this work was to clarify the role of S supply in the development of the response to Fe depletion in Strategy I plants. In S-sufficient plants, Fe-deficiency caused an increase in the Fe(III)-chelate reductase activity, 59Fe uptake rate and ethylene production at root level. This response was associated with increased expression of LeFRO1 [Fe(III)-chelate reductase] and LeIRT1 (Fe2+ transporter) genes. Instead, when S-deficient plants were transferred to a Fe-free solution, no induction of Fe(III)-chelate reductase activity and ethylene production was observed. The same held true for LeFRO1 gene expression, while the increase in 59Fe2+ uptake rate and LeIRT1 gene over-expression were limited. Sulphur deficiency caused a decrease in total sulphur and thiol content; a concomitant increase in 35SO4(2-) uptake rate was observed, this behaviour being particularly evident in Fe-deficient plants. Sulphur deficiency also virtually abolished expression of the nicotianamine synthase gene (LeNAS), independently of the Fe growth conditions. Sulphur deficiency alone also caused a decrease in Fe content in tomato leaves and an increase in root ethylene production; however, these events were not associated with either increased Fe(III)-chelate reductase activity, higher rates of 59Fe uptake or over-expression of either LeFRO1 or LeIRT1 genes. Results show that S deficiency could limit the capacity of tomato plants to cope with Fe-shortage by preventing the induction of the Fe(III)-chelate reductase and limiting the activity and expression of the Fe2+ transporter. Furthermore, the results support the idea that ethylene alone cannot trigger specific Fe-deficiency physiological responses in a Strategy I plant, such as tomato.

  6. Transformer Oil Passivation and Impact of Corrsive Sulphur

    OpenAIRE

    Amaro, P.S.; Pilgrim, J.A.; Lewin, P L; Brown, R.C.D.; Wilson, G.; Jarman, P N

    2012-01-01

    In recent years a significant volume of research has been undertaken in order to understand the recent failures in oil insulated power apparatus due to deposition of copper sulphide on the conductors and in the insulation paper. Dibenzyl Disulfide (DBDS) has been found to be the leading corrosive sulphur compound in the insulation oil [1]. The process of copper sulphide formation and the deposition in the paper is still being investigated, but a recently proposed method seems to be gaining so...

  7. Chronic aspartame intake causes changes in the trans-sulphuration pathway, glutathione depletion and liver damage in mice

    Directory of Open Access Journals (Sweden)

    Isabela Finamor

    2017-04-01

    Full Text Available No-caloric sweeteners, such as aspartame, are widely used in various food and beverages to prevent the increasing rates of obesity and diabetes mellitus, acting as tools in helping control caloric intake. Aspartame is metabolized to phenylalanine, aspartic acid, and methanol. Our aim was to study the effect of chronic administration of aspartame on glutathione redox status and on the trans-sulphuration pathway in mouse liver. Mice were divided into three groups: control; treated daily with aspartame for 90 days; and treated with aspartame plus N-acetylcysteine (NAC. Chronic administration of aspartame increased plasma alanine aminotransferase (ALT and aspartate aminotransferase activities and caused liver injury as well as marked decreased hepatic levels of reduced glutathione (GSH, oxidized glutathione (GSSG, γ-glutamylcysteine ​​(γ-GC, and most metabolites of the trans-sulphuration pathway, such as cysteine, S-adenosylmethionine (SAM, and S-adenosylhomocysteine ​​(SAH. Aspartame also triggered a decrease in mRNA and protein levels of the catalytic subunit of glutamate cysteine ligase (GCLc and cystathionine γ-lyase, and in protein levels of methionine adenosyltransferase 1A and 2A. N-acetylcysteine prevented the aspartame-induced liver injury and the increase in plasma ALT activity as well as the decrease in GSH, γ-GC, cysteine, SAM and SAH levels and GCLc protein levels. In conclusion, chronic administration of aspartame caused marked hepatic GSH depletion, which should be ascribed to GCLc down-regulation and decreased cysteine levels. Aspartame triggered blockade of the trans-sulphuration pathway at two steps, cystathionine γ-lyase and methionine adenosyltransferases. NAC restored glutathione levels as well as the impairment of the trans-sulphuration pathway.

  8. Chronic aspartame intake causes changes in the trans-sulphuration pathway, glutathione depletion and liver damage in mice.

    Science.gov (United States)

    Finamor, Isabela; Pérez, Salvador; Bressan, Caroline A; Brenner, Carlos E; Rius-Pérez, Sergio; Brittes, Patricia C; Cheiran, Gabriele; Rocha, Maria I; da Veiga, Marcelo; Sastre, Juan; Pavanato, Maria A

    2017-04-01

    No-caloric sweeteners, such as aspartame, are widely used in various food and beverages to prevent the increasing rates of obesity and diabetes mellitus, acting as tools in helping control caloric intake. Aspartame is metabolized to phenylalanine, aspartic acid, and methanol. Our aim was to study the effect of chronic administration of aspartame on glutathione redox status and on the trans-sulphuration pathway in mouse liver. Mice were divided into three groups: control; treated daily with aspartame for 90 days; and treated with aspartame plus N-acetylcysteine (NAC). Chronic administration of aspartame increased plasma alanine aminotransferase (ALT) and aspartate aminotransferase activities and caused liver injury as well as marked decreased hepatic levels of reduced glutathione (GSH), oxidized glutathione (GSSG), γ-glutamylcysteine ​​(γ-GC), and most metabolites of the trans-sulphuration pathway, such as cysteine, S-adenosylmethionine (SAM), and S-adenosylhomocysteine ​​(SAH). Aspartame also triggered a decrease in mRNA and protein levels of the catalytic subunit of glutamate cysteine ligase (GCLc) and cystathionine γ-lyase, and in protein levels of methionine adenosyltransferase 1A and 2A. N-acetylcysteine prevented the aspartame-induced liver injury and the increase in plasma ALT activity as well as the decrease in GSH, γ-GC, cysteine, SAM and SAH levels and GCLc protein levels. In conclusion, chronic administration of aspartame caused marked hepatic GSH depletion, which should be ascribed to GCLc down-regulation and decreased cysteine levels. Aspartame triggered blockade of the trans-sulphuration pathway at two steps, cystathionine γ-lyase and methionine adenosyltransferases. NAC restored glutathione levels as well as the impairment of the trans-sulphuration pathway.

  9. Nitrate removal with lateral flow sulphur autotrophic denitrification reactor.

    Science.gov (United States)

    Lv, Xiaomei; Shao, Mingfei; Li, Ji; Xie, Chuanbo

    2014-01-01

    An innovative lateral flow sulphur autotrophic denitrification (LFSAD) reactor was developed in this study; the treatment performance was evaluated and compared with traditional sulphur/limestone autotrophic denitrification (SLAD) reactor. Results showed that nitrite accumulation in the LFSAD reactor was less than 1.0 mg/L during the whole operation. Denitrification rate increased with the increased initial alkalinity and was approaching saturation when initial alkalinity exceeded 2.5 times the theoretical value. Higher influent nitrate concentration could facilitate nitrate removal capacity. In addition, denitrification efficiency could be promoted under an appropriate reflux ratio, and the highest nitrate removal percentage was achieved under reflux ratio of 200%, increased by 23.8% than that without reflux. Running resistance was only about 1/9 of that in SLAD reactor with equal amount of nitrate removed, which was the prominent excellence of the new reactor. In short, this study indicated that the developed reactor was feasible for nitrate removal from waters with lower concentrations, including contaminated surface water, groundwater or secondary effluent of municipal wastewater treatment with fairly low running resistance. The innovation in reactor design in this study may bring forth new ideas of reactor development of sulphur autotrophic denitrification for nitrate-contaminated water treatment.

  10. Sulphur hexafluoride as a stripper gas for tandem accelerators

    Energy Technology Data Exchange (ETDEWEB)

    Hotchkis, M.A.C., E-mail: mah@ansto.gov.au; Child, D.; Fink, D.; Garton, D.; Levchenko, V.; Wilcken, K.

    2013-05-01

    Highlights: •Sulphur hexafluoride is investigated as a stripper gas in tandem accelerators. •For heavy ions at low terminal voltage, mean charge states are found to be up to 1 charge unit higher than with argon gas. •Charge state distributions are found to be broader than with argon gas. •For charge states above the mean charge state, yields are typically doubled using SF{sub 6}. •Using SF{sub 6} stripper gas, the efficiency of actinides AMS analysis is doubled. -- Abstract: We have investigated sulphur hexafluoride as a stripper gas in tandem accelerators by using the ANTARES accelerator system at ANSTO to measure charge state distributions for this gas. Results are reported at 4 MV terminal voltage for injected negative ions ranging from carbon to uranium oxide. For iodine and thorium the distributions are extended across a range of energies of practical use for accelerator mass spectrometry, ion beam analysis and other accelerator applications. Charge state distributions using sulphur hexafluoride are found to have mean charge states up to 1 charge unit higher than, and to be broader than, corresponding distributions for argon gas, except in the case of carbon beams. As a result, SF{sub 6} is shown to provide significantly higher yields for charge states of heavy ions above the mean charge state. We now perform actinide AMS measurements with 9% yield to the 5+ charge state, compared to 4–5% achieved previously with argon gas.

  11. Recent Development of Carbonaceous Materials for Lithium–Sulphur Batteries

    Directory of Open Access Journals (Sweden)

    Xingxing Gu

    2016-11-01

    Full Text Available The effects of climate change are just beginning to be felt, and as such, society must work towards strategies of reducing humanity’s impact on the environment. Due to the fact that energy production is one of the primary contributors to greenhouse gas emissions, it is obvious that more environmentally friendly sources of power are required. Technologies such as solar and wind power are constantly being improved through research; however, as these technologies are often sporadic in their power generation, efforts must be made to establish ways to store this sustainable energy when conditions for generation are not ideal. Battery storage is one possible supplement to these renewable energy technologies; however, as current Li-ion technology is reaching its theoretical capacity, new battery technology must be investigated. Lithium–sulphur (Li–S batteries are receiving much attention as a potential replacement for Li-ion batteries due to their superior capacity, and also their abundant and environmentally benign active materials. In the spirit of environmental harm minimization, efforts have been made to use sustainable carbonaceous materials for applications as carbon–sulphur (C–S composite cathodes, carbon interlayers, and carbon-modified separators. This work reports on the various applications of carbonaceous materials applied to Li–S batteries, and provides perspectives for the future development of Li–S batteries with the aim of preparing a high energy density, environmentally friendly, and sustainable sulphur-based cathode with long cycle life.

  12. Acid Rain Limits Global Warming

    Institute of Scientific and Technical Information of China (English)

    Will Knight; 张林玲

    2004-01-01

    @@ Acid rain restricts global warming by reducing methane① emissions from natural wetland areas, suggests a global climate study. Acid rain is the result of industrial pollution,which causes rainwater to carry small quantities of acidic compoumds② such as sulphuric and nitric acid③. Contaminated rainwater can upset rivers and lakes, killing fish and other organisms and also damage plants, trees and buildings.

  13. Copper toxicity in Chinese cabbage is not influenced by plant sulphur status, but affects sulphur metabolism-related gene expression and the suggested regulatory metabolites

    NARCIS (Netherlands)

    Shahbaz, M.; Stuiver, C. E. E.; Posthumus, F. S.; Parmar, S.; Hawkesford, M. J.; De Kok, L. J.

    The toxicity of high copper (Cu) concentrations in the root environment of Chinese cabbage (Brassica pekinensis) was little influenced by the sulphur nutritional status of the plant. However, Cu toxicity removed the correlation between sulphur metabolism-related gene expression and the suggested

  14. An air-pressure-free elastomeric valve for integrated nucleic acid analysis by capillary electrophoresis

    Science.gov (United States)

    Jung, Wooseok; Barrett, Matthew; Brooks, Carla; Rivera, Andrew; Birdsell, Dawn N.; Wagner, David M.; Zenhausern, Frederic

    2015-12-01

    We present a new elastomeric valve for integrated nucleic acid analysis by capillary electrophoresis. The valve functions include metering to capture a designated volume of biological sample into a polymerase chain reaction (PCR) chamber, sealing to preserve the sample during PCR cycling, and transfer of the PCR-products and on-chip formamide post-processing for the analysis of DNA fragments by capillary gel electrophoresis. This new valve differs from prior art polydimethylsiloxane (PDMS) valves in that the valve is not actuated externally by air-pressure or vacuum so that it simplifies a DNA analysis system by eliminating the need for an air-pressure or vacuum source, and off-cartridge solenoid valves, control circuit boards and software. Instead, the new valve is actuated by a thermal cycling peltier assembly integrated within the hardware instrument that tightly comes in contact with a microfluidic cartridge for thermal activation during PCR, so that it spontaneously closes the valve without an additional actuator system. The valve has bumps in the designated locations so that it has a self-alignment that does not require precise alignment of a valve actuator. Moreover, the thickness of the new valve is around 600 μm with an additional bump height of 400 μm so that it is easy to handle and very feasible to fabricate by injection molding compared to other PDMS valves whose thicknesses are around 30-100 μm. The new valve provided over 95% of metering performance in filling the fixed volume of the PCR chamber, preserved over 97% of the sample volume during PCR, and showed very comparable capillary electrophoresis peak heights to the benchtop assay tube controls with very consistent transfer volume of the PCR-product and on-chip formamide. The new valve can perform a core function for integrated nucleic acid analysis by capillary electrophoresis.

  15. Recovery of Zn from acid mine water and electric arc furnace dust in an integrated process.

    Science.gov (United States)

    Carranza, Francisco; Romero, Rafael; Mazuelos, Alfonso; Iglesias, Nieves

    2016-01-01

    In this paper, the purification of acid mine water and the treatment of electric arc furnace dust (EAFD) are integrated into one process with the aim of recovering the Zn content of both effluent and waste. Zinc recovery can reduce the cost of their environmental management: purified acid mine water is discharged after removing all metals; EAFD ceases to be hazardous waste; and Zn is valorised. The process consists of the recovery of Zn as zinc oxide and its purification into commercial products. First, EAFD is leached with acid water and the dissolved metals are selectively precipitated as hydroxides. After EADF leaching, ferrous iron is bio-oxidized and Fe and Al are then precipitated; in the following stage, Cu, Ni, Co and Cd are cemented and finally Zn is precipitated as ZnO. In order to purify water that finally is discharged to a river, lime is used as the neutralizing agent, which results in a precipitate of mainly gypsum, MnO, and ZnO. From the impure zinc oxide produced, various alternatives for the attainment of commercial products, such as basic zinc carbonate and electrolytic zinc, are studied in this work.

  16. FGF15/FGFR4 integrates growth factor signaling with hepatic bile acid metabolism and insulin action.

    Science.gov (United States)

    Shin, Dong-Ju; Osborne, Timothy F

    2009-04-24

    The current studies show FGF15 signaling decreases hepatic forkhead transcription factor 1 (FoxO1) activity through phosphatidylinositol (PI) 3-kinase-dependent phosphorylation. The bile acid receptor FXR (farnesoid X receptor) activates expression of fibroblast growth factor (FGF) 15 in the intestine, which acts through hepatic FGFR4 to suppress cholesterol-7alpha hydroxylase (CYP7A1) and limit bile acid production. Because FoxO1 activity and CYP7A1 gene expression are both increased by fasting, we hypothesized CYP7A1 might be a FoxO1 target gene. Consistent with recently reported results, we show CYP7A1 is a direct target of FoxO1. Additionally, we show that the PI 3-kinase pathway is key for both the induction of CYP7A1 by fasting and the suppression by FGF15. FGFR4 is the major hepatic FGF receptor isoform and is responsible for the hepatic effects of FGF15. We also show that expression of FGFR4 in liver was decreased by fasting, increased by insulin, and reduced by streptozotocin-induced diabetes, implicating FGFR4 as a primary target of insulin regulation. Because insulin and FGF both target the PI 3-kinase pathway, these observations suggest FoxO1 is a key node in the convergence of FGF and insulin signaling pathways and functions as a key integrator for the regulation of glucose and bile acid metabolism.

  17. Effects of alpha-lipoic acids on sperm membrane integrity during liquid storage of boar semen

    Directory of Open Access Journals (Sweden)

    Laura Parlapan

    2015-05-01

    Full Text Available Preliminary studies have shown that sperm membrane from swine shows high sensitivity to cryopreservation process, causing a dramatic reduction in sperm quality. This has been attributed to the production of reactive oxygen species, that cause lipid peroxidation in sperm membranes. The aim of the present study was to minimize the oxidative attack by adding different concentration of alpha-lipoic acid into the sperm liquid storage at 17ºC for 7 days. Freshly ejaculated boar semen was diluted with Beltsville Thawing Solution (BTS and supplemented with 5 levels of alpha-lipoic  acid (0.015, 0.02, 0.05, 0.1, 0.15 mmol/ml. The membrane integrity was evaluated at days 0, 1, 3, 5 and 7 of liquid preservation, using flow cytometer FACSCanto II (BD Biociencias systems. The experiment indicate that supplementation of alpha-lipoic  acid to the semen liquid storage extender improve sperm membrane

  18. Quantification of chemical sulphur species in bulk soil and organic sulphur fractions by S K-edge Xanes spectroscopy

    DEFF Research Database (Denmark)

    Boye, K; Almkvist, G; Nilsson, S I

    2011-01-01

    A new data treatment method for fitting spectra obtained by sulphur (S) K-edge X-ray absorption near-edge structure (XANES) spectroscopy was used to quantify the chemical S speciation at three experimental sites with arable soils receiving the same long-term field treatments. Two treatments, crop...... the opposite trend was observed. Sulphur XANES spectroscopy of acetylacetone extracts of physically protected and unprotected organic S in two of the soils revealed that physical protection was not related to S speciation; however, intermediate forms of oxidized S species appeared to accumulate in the residual...... enhanced the reliability of quantitative determination of contributing S species in soil samples and soil extracts. The results indicated that long-term FYM application shifted S species composition from highly oxidized towards intermediate oxidization in two of the soils, but in the third soil...

  19. Biogas--municipal solid waste incinerator bottom ash interactions: sulphur compounds removal.

    Science.gov (United States)

    Ducom, Gaëlle; Radu-Tirnoveanu, Daniela; Pascual, Christophe; Benadda, Belkacem; Germain, Patrick

    2009-07-30

    This study focuses on a new way of reusing municipal solid waste incinerator bottom ash: landfill gas purification before energetic valorisation. A pilot plant was designed and operated on a landfill site located in France (Loire). One kilogram bottom ash is able to sequestrate more than 3.0 g of hydrogen sulphide, 44 mg of methyl mercaptan, and 86 mg of dimethyl sulphide. Hydrogen sulphide retention is probably due to acid-basic reactions conducting to sulphur mineralisation under the form of low solubility metal sulphides. The reaction medium is hydration water. The retention mechanism for methyl mercaptan is probably similar but dimethyl sulphide is most likely retained by physical adsorption. As methane is not retained by bottom ash, the landfill gas energetic content will not be lowered. There seems to be no appreciable difference in these results whether bottom ash is fresh or carbonated. These results are encouraging in the perspective of a field scale application of this biogas treatment process.

  20. Optimization of digestion parameters for analysing the total sulphur of mine tailings by inductively coupled plasma optical emission spectrometry.

    Science.gov (United States)

    Alam, Raquibul; Shang, Julie Q; Cheng, Xiangrong

    2012-05-01

    The oxidation of sulphidic mine tailings and consequent acid generation poses challenges for the environment. Accurate and precise analysis of sulphur content is necessary for impact assessment and management of mine tailings. Here, the authors aim at developing a rapid and easy digestion procedure, which may analyse and measure the total amount of sulphur in mine tailings by using inductively coupled plasma. For evaluating effects of several variables, the researchers used a univariate (analysis of variance (ANOVA)) strategy and considered factors such as composition of the acid mixture, heating time, and refluxing device to optimize the performance. To do the experiment, the researchers have used two certified reference materials (KZK-1 and RTS-2) and samples of tailings from Musselwhite mine. ANOVA result shows that heating time is the most influencing factor on acid digestion of the reference materials whereas in case of a digestion of tailings sample, hydrochloric acid proved to be the most significant parameter. Satisfactory results between the measured and referenced values are found for all experiments. It is found that the aqua regia (1 ml HNO(3) + 3 ml HCl) digestion of 0.1 g of samples after only 40 min of heating at 95°C produced fast, safe, and accurate analytical results with a recovery of 97% for the selected reference materials.

  1. 1, 5-BIS [(4-DITHIOCARBOXYLATE-1-DODECYL-5-HYDROXY-3-METHYLPYRAZOLYL] PENTANE AS COPPER CORROSION INHIBITOR IN 0.1 M SULPHURIC ACID 1, 5-Bis [(4-Dithiocarboxylat-1-dodecyl-5-Hydroxy-3-METHYL PYRAZOLYL] Pentan als Kupferkorrosionsinhibitor in 0,1 M SCHWEFELSÄURE

    Directory of Open Access Journals (Sweden)

    Rosa Vera, Alfonso Oliva and Aurora Molinari

    2011-08-01

    Full Text Available The ability of tetradentate ligand 1,5-bis[(4-dithiocarboxylate-1-dodecyl-5-hydroxy-3- methylpyrazolyl]pentane (H2BDTCPP as organic surface coating to inhibit the copper corrosion in 0.1 M H2SO4 have been studied. The inhibitory properties were studied by immersion assays and the results show that H2BDTCPP behaves as a mixed inhibitor in 0.1 M H2SO4 aqueous solution, with an inhibition efficiency of 62.1 %, increasing the corrosion potential and decreasing the corrosion current of copper when it is coated over the metal surface. These properties can be attributed to the planar aromatic structure of the pyrazolyldithiocarboxylate group and to the high π/lone-pair electron density due to nitrogen, oxygen and sulphur which favour its physical and chemical adsorption.

  2. An integrated metabonomics and transcriptomics approach to understanding metabolic pathway disturbance induced by perfluorooctanoic acid.

    Science.gov (United States)

    Peng, Siyuan; Yan, Lijuan; Zhang, Jie; Wang, Zhanlin; Tian, Meiping; Shen, Heqing

    2013-12-01

    Perfluorooctanoic acid (PFOA) is one of the most representative perfluorinated compounds and liver is the major organ where PFOA is accumulated. Although the multiple toxicities had been reported, its toxicological profile remained unclear. In this study, a systems toxicology strategy integrating liquid chromatography/mass spectrometry-based metabonomics and transcriptomics analyses was applied for the first time to investigate the effects of PFOA on a representative Chinese normal human liver cell line L-02, with focusing on the metabolic disturbance. Fifteen potential biomarkers were identified on metabolic level and most observations were consistent with the altered levels of gene expression. Our results showed that PFOA induced the perturbations in various metabolic processes in L-02 cells, especially lipid metabolism-related pathways. The up-stream mitochondrial carnitine metabolism was proved to be influenced by PFOA treatment. The specific transformation from carnitine to acylcarnitines, which showed a dose-dependent effect, and the expression level of key genes involved in this pathway were observed to be altered correspondingly. Furthermore, the down-stream cholesterol biosynthesis was directly confirmed to be up-regulated by both increased cholesterol content and elevated expression level of key genes. The PFOA-induced lipid metabolism-related effects in L-02 cells started from the fatty acid catabolism in cytosol, fluctuated to the processes in mitochondria, extended to the cholesterol biosynthesis. Many other metabolic pathways like amino acid metabolism and tricarboxylic acid cycle might also be disturbed. The findings obtained from the systems biological research provide more details about metabolic disorders induced by PFOA in human liver.

  3. Pre-treatment of ligno-cellulose with biological acid recycling (the Biosulfurol process)

    NARCIS (Netherlands)

    Groenestijn, van J.W.; Hazewinkel, J.H.O.; Bakker, R.R.

    2008-01-01

    A biomass pretreatment process is being developed based on contacting ligno-cellulosic biomass with 70% sulphuric acid and subsequent hydrolysis by adding water. In this process, the hydrolysate can be fermented yielding ethanol, while the sulphuric acid is partly recovered by anion-selective membra

  4. Proton transport in triflic acid pentahydrate studied via ab initio path integral molecular dynamics.

    Science.gov (United States)

    Hayes, Robin L; Paddison, Stephen J; Tuckerman, Mark E

    2011-06-16

    Trifluoromethanesulfonic acid hydrates provide a well-defined system to study proton dissociation and transport in perfluorosulfonic acid membranes, typically used as the electrolyte in hydrogen fuel cells, in the limit of minimal water. The triflic acid pentahydrate crystal (CF(3)SO(3)H·5H(2)O) is sufficiently aqueous that it contains an extended three-dimensional water network. Despite it being extended, however, long-range proton transport along the network is structurally unfavorable and would require considerable rearrangement. Nevertheless, the triflic acid pentahydrate crystal system can provide a clear picture of the preferred locations of local protonic defects in the water network, which provides insights about related structures in the disordered, low-hydration environment of perfluorosulfonic acid membranes. Ab initio molecular dynamics simulations reveal that the proton defect is most likely to transfer to the closest water that has the expected presolvation and only contains water in its first solvation shell. Unlike the tetrahydrate of triflic acid (CF(3)SO(3)H·4H(2)O), there is no evidence of the proton preferentially transferring to a water molecule bridging two of the sulfonate groups. However, this could be an artifact of the crystal structure since the only such water molecule is separated from the proton by long O-O distances. Hydrogen bonding criteria, using the two-dimensional potential of mean force, are extracted. Radial distribution functions, free energy profiles, radii of gyration, and the root-mean-square displacement computed from ab initio path integral molecular dynamics simulations reveal that quantum effects do significantly extend the size of the protonic defect and increase the frequency of proton transfer events by nearly 15%. The calculated IR spectra confirm that the dominant protonic defect mostly exists as an Eigen cation but contains some Zundel ion characteristics. Chain lengths and ring sizes determined from the

  5. Production of citric acid using its extraction wastewater treated by anaerobic digestion and ion exchange in an integrated citric acid-methane fermentation process.

    Science.gov (United States)

    Xu, Jian; Chen, Yang-Qiu; Zhang, Hong-Jian; Tang, Lei; Wang, Ke; Zhang, Jian-Hua; Chen, Xu-Sheng; Mao, Zhong-Gui

    2014-08-01

    In order to solve the problem of extraction wastewater pollution in citric acid industry, an integrated citric acid-methane fermentation process is proposed in this study. Extraction wastewater was treated by mesophilic anaerobic digestion and then used to make mash for the next batch of citric acid fermentation. The recycling process was done for seven batches. Citric acid production (82.4 g/L on average) decreased by 34.1 % in the recycling batches (2nd-7th) compared with the first batch. And the residual reducing sugar exceeded 40 g/L on average in the recycling batches. Pigment substances, acetic acid, ammonium, and metal ions in anaerobic digestion effluent (ADE) were considered to be the inhibitors, and their effects on the fermentation were studied. Results indicated that ammonium, Na(+) and K(+) in the ADE significantly inhibited citric acid fermentation. Therefore, the ADE was treated by acidic cation exchange resin prior to reuse to make mash for citric acid fermentation. The recycling process was performed for ten batches, and citric acid productions in the recycling batches were 126.6 g/L on average, increasing by 1.7 % compared with the first batch. This process could eliminate extraction wastewater discharge and reduce water resource consumption.

  6. Volatile displacement of Meghalaya coals – A pointer to explore low sulphur coals

    Indian Academy of Sciences (India)

    P Behera

    2007-04-01

    Volatile displacement, which measures the difference between calculated and experimental volatile matter, is indicative of abnormality in coals which may be related to petrological or chemical parameters. The volatile displacement () values of Meghalaya coals were calculated from their chemical analyses. Correlations of volatile displacement () with parameters such as carbon, hydrogen, moisture, oxygen, oxygen plus sulphate sulphur, oxygen plus pyritic sulphur, oxygen plus organic sulphur and total sulphur were studied. An approximately linear relationship exists only between and moisture, and and total sulphur, and not between other parameters. Plots on Seyler’s chart indicate the coals as perhydrous to orthohydrous. The linear relationship with total sulphur indicates that the coals may have become abnormal mainly due to the marine environment of deposition and weathering.

  7. Determination of the wine preservative sulphur dioxide with cyclic voltammetry using inkjet printed electrodes.

    Science.gov (United States)

    Schneider, Marion; Türke, Alexander; Fischer, Wolf-Joachim; Kilmartin, Paul A

    2014-09-15

    During winemaking sulphur dioxide is added to prevent undesirable reactions. However, concerns over the harmful effects of sulphites have led to legal limits being placed upon such additives. There is thus a need for simple and selective determinations of sulphur dioxide in wine, especially during winemaking. The simultaneous detection of polyphenols and sulphur dioxide, using cyclic voltammetry at inert electrodes is challenging due to close oxidation potentials. In the present study, inkjet printed electrodes were developed with a suitable voltammetric signal on which the polyphenol oxidation is suppressed and the oxidation peak height for sulphur dioxide corresponds linearly to the concentration. Different types of working electrodes were printed. Electrodes consisting of gold nanoparticles mixed with silver showed the highest sensitivity towards sulphur dioxide. Low cost production of the sensor elements and ultra fast determination of sulphur dioxide by cyclic voltammetry makes this technique very promising for the wine industry. Copyright © 2014 Elsevier Ltd. All rights reserved.

  8. Bile acid mediated effects on gut integrity and performance of early-weaned piglets

    DEFF Research Database (Denmark)

    de Diego-Cabero, Nuria; Mereu, Alessandro; Menoyo, David;

    2015-01-01

    of the study on day 35. On days 1, 7 and 14 blood samples were collected from 6 pigs per treatment to measure plasma GLP-2. On day 15, 6 pigs per treatment were euthanized to obtain intestinal tissue samples for later histological and gene expression analyses. Results Supplementing the diet with CDC tended...... small intestine. Conclusions This study showed that the oral administration of CDC to early-weaned pigs has the potential to improve the protection......Background Early weaning (EW) results in a transient period of impaired integrity of the intestinal mucosa that may be associated with reduced plasma concentration of glucagon-like peptide-(GLP) 2. We have previously shown that intragastric infusion of chenodeoxycholic acid (CDC) increases...

  9. THE RELATIONSHIP BETWEEN BATCH REDOX AND SULPHUR BUBBLE DEFECT OF GLASS

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Bubble defects of glass were studied by Ruman spectrum, C equivalent of glass raw materials were analyzed by chemical method, and the solubility of sulphur in glass was determined with SC-132 Sulphur Determination. Then, the relationship between glass bubble, the redox numbers of glass batch and the solubility of sulphur in float glass were discussed. The way that can improve the quality of float glass was found.

  10. Study on Friction and Wear Characteristics and Structure of Compound Layer from Combined Treatment of Ion Nitrocarburizing-Ion Sulphurizing of CrMoCu Alloy Cast Iron

    Institute of Scientific and Technical Information of China (English)

    MA Shi-ning; HU Chun-hua; LI Xin; QIU Ji

    2004-01-01

    The technics of combined treatment of ion nitrocarburizing-ion sulphurizing of CrMoCu alloy cast iron has been investigated and the compound layer with nitrocarbonide and sulphide has been made on the surface of CrMoCu alloy cast iron. The compound layer is composed of sulfide surface layer and the nitrocarbonide hypo-surface layer and its diffusing layer. The size of sulfide globular grains distributing equably on the surface is in nano-micron-scale, and the phase structure of the compound layer is composed of FeS、 FeS2、 Fe2C and Fe3N. Under dry sliding condition, the friction-reducing of sulphurized surface is good, but its function time can't last very long. The nitrocarbonided+sulphurized surface can greatly improve the wear-resistance and the friction-reducing of CrMoCu alloy cast iron, and its integrated friction and wear properties are better than plain and sulphurized surfaces'.

  11. Molecular classification based on apomorphic amino acids (Arthropoda, Hexapoda): Integrative taxonomy in the era of phylogenomics.

    Science.gov (United States)

    Wu, Hao-Yang; Wang, Yan-Hui; Xie, Qiang; Ke, Yun-Ling; Bu, Wen-Jun

    2016-06-17

    With the great development of sequencing technologies and systematic methods, our understanding of evolutionary relationships at deeper levels within the tree of life has greatly improved over the last decade. However, the current taxonomic methodology is insufficient to describe the growing levels of diversity in both a standardised and general way due to the limitations of using only morphological traits to describe clades. Herein, we propose the idea of a molecular classification based on hierarchical and discrete amino acid characters. Clades are classified based on the results of phylogenetic analyses and described using amino acids with group specificity in phylograms. Practices based on the recently published phylogenomic datasets of insects together with 15 de novo sequenced transcriptomes in this study demonstrate that such a methodology can accommodate various higher ranks of taxonomy. Such an approach has the advantage of describing organisms in a standard and discrete way within a phylogenetic framework, thereby facilitating the recognition of clades from the view of the whole lineage, as indicated by PhyloCode. By combining identification keys and phylogenies, the molecular classification based on hierarchical and discrete characters may greatly boost the progress of integrative taxonomy.

  12. Esophageal sensitivity to acid in patients with Barrett's esophagus is not related to preserved esophageal mucosal integrity.

    Science.gov (United States)

    Weijenborg, P W; Smout, A J P M; Krishnadath, K K; Bergman, J G H M; Verheij, J; Bredenoord, A J

    2017-07-01

    Patients with Barrett's esophagus (BE) usually have severe gastroesophageal reflux. However, they often have surprisingly few reflux symptoms. We hypothesized that BE patients are less sensitive to acid than gastroesophageal reflux disease (GERD) patients without Barrett and that this is due to an unusual preservation of mucosal integrity of the squamous epithelium prohibiting transepithelial acid diffusion. We prospectively analyzed esophageal sensitivity and esophageal mucosal integrity in GERD patients with and without BE and healthy subjects. An acid perfusion test was performed and mucosal integrity was assessed in vivo by electrical tissue impedance spectroscopy and ex vivo by Ussing chamber experiments with biopsy specimens. Gastroesophageal reflux disease patients with BE were less sensitive to acid than GERD patients without BE, but more sensitive to acid than healthy controls (time to perception Barrett's 14.0 minutes, GERD 4.6 minutes, controls 17.5 minutes). However, extracellular impedance (6.2 and 5.7 vs 8.4×10(3)  Ω/m) and transepithelial resistance (94.0 and 89 vs 118 Ω/cm(2) ) was similar in BE and GERD patients and significantly lower than in healthy subjects. Transepithelial fluorescein flux was equally increased in GERD patients with and without BE (1.6 and 1.7×10(3) vs 0.6×10(3)  nmol/cm(2) /h). Esophageal hypersensitivity to acid is less pronounced in BE patients than in GERD patients without Barrett. However, mucosal integrity of the squamous epithelium is equally impaired in GERD patients with and without Barrett, indicating that factors other than esophageal mucosal barrier integrity explain the difference in acid sensitivity between those with BE and those without. © 2017 John Wiley & Sons Ltd.

  13. Proton transport in triflic acid hydrates studied via path integral car-parrinello molecular dynamics.

    Science.gov (United States)

    Hayes, Robin L; Paddison, Stephen J; Tuckerman, Mark E

    2009-12-31

    The mono-, di-, and tetrahydrates of trifluoromethanesulfonic acid, which contain characteristic H(3)O(+), H(5)O(2)(+), and H(9)O(4)(+) structures, provide model systems for understanding proton transport in materials with high perfluorosulfonic acid density such as perfluorosulfonic acid membranes commonly employed in hydrogen fuel cells. Ab initio molecular dynamics simulations indicate that protons in these solids are predisposed to transfer to the water most strongly bound to sulfonate groups via a Grotthuss-type mechanism, but quickly return to the most solvated defect structure either due to the lack of a nearby species to stabilize the new defect or a preference for the proton to be maximally hydrated. Path integral molecular dynamics of the mono- and dihydrate reveal significant quantum effects that facilitate proton transfer to the "presolvated" water or SO(3)(-) in the first solvation shell and increase the Zundel character of all the defects. These trends are quantified in free energy profiles for each bonding environment. Hydrogen bonding criteria for HOH-OH(2) and HOH-O(3)S are extracted from the two-dimensional potential of mean force. The quantum radial distribution function, radius of gyration, and root-mean-square displacement position correlation function show that the protonic charge is distributed over two or more water molecules. Metastable structural defects with one excess proton shared between two sulfonate groups and another Zundel or Eigen type cation defect are found for the mono- and dihydrate but not for the tetrahydrate crystal. Results for the tetrahydrate native crystal exhibit minor differences at 210 and 250 K. IR spectra are calculated for all native and stable defect structures. Graph theory techniques are used to characterize the chain lengths and ring sizes in the hydrogen bond network. Low conductivities when limited water is present may be attributable to trapping of protons between SO(3)(-) groups and the increased

  14. An integrated portable hand-held analyser for real-time isothermal nucleic acid amplification.

    Science.gov (United States)

    Smith, Matthew C; Steimle, George; Ivanov, Stan; Holly, Mark; Fries, David P

    2007-08-29

    A compact hand-held heated fluorometric instrument for performing real-time isothermal nucleic acid amplification and detection is described. The optoelectronic instrument combines a Printed Circuit Board/Micro Electro Mechanical Systems (PCB/MEMS) reaction detection/chamber containing an integrated resistive heater with attached miniature LED light source and photo-detector and a disposable glass waveguide capillary to enable a mini-fluorometer. The fluorometer is fabricated and assembled in planar geometry, rolled into a tubular format and packaged with custom control electronics to form the hand-held reactor. Positive or negative results for each reaction are displayed to the user using an LED interface. Reaction data is stored in FLASH memory for retrieval via an in-built USB connection. Operating on one disposable 3 V lithium battery >12, 60 min reactions can be performed. Maximum dimensions of the system are 150 mm (h) x 48 mm (d) x 40 mm (w), the total instrument weight (with battery) is 140 g. The system produces comparable results to laboratory instrumentation when performing a real-time nucleic acid sequence-based amplification (NASBA) reaction, and also displayed comparable precision, accuracy and resolution to laboratory-based real-time nucleic acid amplification instrumentation. A good linear response (R2 = 0.948) to fluorescein gradients ranging from 0.5 to 10 microM was also obtained from the instrument indicating that it may be utilized for other fluorometric assays. This instrument enables an inexpensive, compact approach to in-field genetic screening, providing results comparable to laboratory equipment with rapid user feedback as to the status of the reaction.

  15. INTERACTION OF SULPHUR WITH BIMETALLIC SURFACES: EFFECTS OF STRUCTURAL, ELECTRONIC AND CHEMICAL PROPERTIES.

    Energy Technology Data Exchange (ETDEWEB)

    RODRIGUEZ,J.A.; HRBEK,J.

    2001-10-04

    In recent years, several new interesting phenomena have been discovered when studying the interaction of sulphur with bimetallic surfaces using the modern techniques of surface science. Very small amounts of sulphur can induce dramatic changes in the morphology of bimetallic surfaces. The electronic perturbations associated with the formation of a heteronuclear metal-metal bond affect the reactivity of the bonded metals toward sulphur. This can be a very important issue to consider when trying to minimize the negative effects of sulphur poisoning or dealing with the design of desulfurization catalysts.

  16. Effect of nitrocarburizing on sulphide layer during nitrocarburizing-sulphurating treatment

    Institute of Scientific and Technical Information of China (English)

    LI Xin; MA Shi-ning; LIU Ji-yan

    2005-01-01

    Compared with the single sulphurating treatment, the duplex treatment of nitrocarburizing-sulphurating can more effectively improve the properties of steel such as friction-reducing, wear resistance and anti-scuffing. Under the same processing parameters, the sulphide layers were fabricated on the surface of CrMoCu alloy cast iron by single ion-sulphurating treatment and nitrocarburizing-sulphurating duplex treatment, respectively. Through the analysis of the sulphide, the effect of the nitrocarburizing on the fabrication of the sulphide layer was investigated. And the result shows that the fabrication of sulphide layer is promoted by the nitrocarburizing treatment.

  17. Integrated adsorptive technique for efficient recovery of m-cresol and m-toluidine from actual acidic and salty wastewater.

    Science.gov (United States)

    Chen, Da; Liu, Fuqiang; Zong, Lidan; Sun, Xiaowen; Zhang, Xiaopeng; Zhu, Changqing; Tao, Xuewen; Li, Aimin

    2016-07-15

    An integrated adsorptive technique combining an m-cresol adsorption unit, an acid retardation unit and an m-toluidine adsorption unit in sequence was designed to recover m-cresol and m-toluidine from highly acidic and salty m-cresol manufacturing wastewater. In the first column packed with hypercrosslinked polymeric resin (NDA-99), most m-cresol was captured through π-π and hydrogen-bonding interactions as well as the salting-out effect, while m-toluidine was not absorbed due to protonation. To separate acid from salt, an acid retardation unit was introduced successively to adsorb sulfuric acid by strong base anion exchange resin (201×7). After the acid retardation unit and mild neutralization reaction, the last column filled with NDA-99 was applied to trap neutral m-toluidine from the salty effluent. Moreover, the eluent of the acid retardation unit was utilized as the regenerant to recover m-toluidine, and the recycled high-acidity and low-salinity solution of m-toluidine was directly used to produce m-cresol as the raw material. Therefore, the proposed method not only efficiently recycled m-cresol and m-toluidine, but also reduced the consumption of alkali dramatically (saving 0.1628t/t wastewater). These findings will inspire design of integrated adsorptive techniques for treating complex organic wastewater with high efficiency and low cost.

  18. INVESTIGATION OF DISSOLVED SULPHATE IN VARIOUS GEOTHERMAL FIELDS OF SUMATRA USING OXYGEN AND SULPHUR ISOTOPES

    Directory of Open Access Journals (Sweden)

    E. Ristin Pujiindiyati

    2010-06-01

    Full Text Available There are at least 30 high temperature systems; eleven active volcanoes, five degassing volcanoes and one caldera volcano controlled by Sumatra Fault Zone over a length of 1700 km. To understand this geothermal field system, some information about geochemistry including isotope composition in its fluid is needed. Sulphur-34 and oxygen-18 isotopes in dissolved sulphate pair have been used to determine the origin of acidic fluid of sulphate and to evaluate the process involved. The fluids from eight hot springs, two fumaroles, four deep wells and crater have been collected in along Sumatra geothermal fields. Sulphur-34 (d 34S (SO4, 0/00 CDT and oxygen-18 (d 18O (SO4, 0/00 SMOW in sulphate is analyzed according to Robinson-Kusakabe and Rafter method, respectively. The d 34S (SO4 values from Sibayak wells are more enriched of 16.8 0/00 to 18.2 0/0 that may indicate the dissolution of anhydrite minerals or isotope partitioning in hydration of SO2. The d 34S (SO4 values from two fumaroles (Pusuk Bukit - North Sumatra and Rantau Dadap - South Sumatra are at depleted value of -0.150/00 and 1.80/00, those are close to d 34S from magmatic sulphur.  In general, the d 34S (SO4 of springs spread in a wide range of 5.250/00 to14.20/00 and show a mixing process between atmospheric sulphate and sulphate from deep wells. The d 18O (SO4 from wells exhibits depleted value around -3.60/00 suggesting that 87.5% of sulphate oxygen is derived from groundwater oxygen and 12.5% is derived from atmospheric molecular oxygen in sulphide oxidation reaction. In the other hand, hot springs (except Semurup, crater and fumaroles have enriched value of d 18O (SO4. These enriched values suggest that a higher percentage of atmospherically derived oxygen compared to those from the depth.   Keywords: isotope, geothermal, Sumatra

  19. A sulphur deficiency-induced gene, sdi1, involved in the utilization of stored sulphate pools under sulphur-limiting conditions has potential as a diagnostic indicator of sulphur nutritional status.

    Science.gov (United States)

    Howarth, Jonathan R; Parmar, Saroj; Barraclough, Peter B; Hawkesford, Malcolm J

    2009-02-01

    A sulphate deficiency-induced gene, sdi1, has been identified by cDNA-amplified fragment length polymorphism (AFLP) analysis utilizing field-grown, nutrient-deficient wheat (Triticum aestivum var. Hereward). The expression of sdi1 was specifically induced in leaf and root tissues in response to sulphate deficiency, but was not induced by nitrogen, phosphorus, potassium or magnesium deficiency. Expression was also shown to increase in plant tissues as the external sulphate concentration in hydroponically grown plants was reduced from 1.0 to 0.0 mm. On this basis, sdi1 gene expression has potential as a sensitive indicator of sulphur nutritional status in wheat. Genome-walking techniques were used to clone the 2.7-kb region upstream of sdi1 from genomic DNA, revealing several cis-element motifs previously identified as being associated with sulphur responses in plants. The Arabidopsis thaliana gene most highly homologous to sdi1 is At5g48850, which was also demonstrated to be induced by sulphur deficiency, an observation confirmed by the analysis of microarray data available in the public domain. The expression of Atsdi1 was induced more rapidly than previously characterized sulphur-responsive genes in the period immediately following the transfer of plants to sulphur-deficient medium. Atsdi1 T-DNA 'knockout' mutants were shown to maintain higher tissue sulphate concentrations than wild-type plants under sulphur-limiting conditions, indicating a role in the utilization of stored sulphate under sulphur-deficient conditions. The structural features of the sdi1 gene and its application in the genetic determination of the sulphur nutritional status of wheat crops are discussed.

  20. Electron transfer dynamics across self-assembled N-(2-mercaptoethyl) octadecanamide/mycolic acid layers: impedimetric insights into the structural integrity and interaction with anti-mycolic acid antibodies

    CSIR Research Space (South Africa)

    Ozoemena, KI

    2010-01-01

    Full Text Available The integrity and properties of mycolic acid (MA) antigens integrated into a self-assembled monolayer (SAM) of N-(2-mercaptoethyl)octadecanamide, (MEODA), on a gold electrode have been interrogated using cyclic voltammetry (CV) and electrochemical...

  1. The impacts of future climate change and sulphur emission reductions on acidification recovery at Plastic Lake, Ontario

    Directory of Open Access Journals (Sweden)

    J. Aherne

    2008-03-01

    Full Text Available Climate-induced drought events have a significant influence on sulphate export from forested catchments in central Ontario, subsequently delaying the recovery of surface waters from acidification. In the current study, a model chain that employed a statistical downscaling model, a hydrological model and two hydrochemical models was used to forecast the chemical recovery of Plastic Lake sub-catchment 1 (PC1 from acidification under proposed deposition reductions and the A2 emission scenario of the Intergovernmental Panel on Climate Change. Any predicted recovery in stream acid neutralising capacity and pH owing to deposition reductions were clearly offset by large acid effluxes from climate-induced drought events. By 2100, ANC is predicted to show large variations ranging between 10 and −30 μmolc L−1. Similarly, predicted pH in 2100 is lower (>0.05 of a pH unit than the value simulated for 2000 (pH 4.35. Despite emission reductions, the future scenario paints a bleak picture of reacidification at PC1 to levels commensurate with those of the late 1970s. The principal process behind this reacidification is the oxidation of previously stored (reduced sulphur compounds in wetlands during periods of low-flow (or drought, with subsequent efflux of sulphate upon re-wetting. Simulated catchment runoff under the A2 emissions scenario predictes increased intensity and frequency of low-flow events from approximately 2030 onwards. The Integrated Catchments model for Carbon indicated that stream DOC concentrations at PC1 will also increase under the future climate scenario, with temperature being the principal driver. Despite the predicted (significant increase in DOC, pH is not predicted to further decline (beyond the climate-induced oxidation scenario, instead pH shows greater variability throughout the simulation. As echoed by many recent studies, hydrochemical models and model frameworks need to incorporate the drivers

  2. The impacts of future climate change and sulphur emission reductions on acidification recovery at Plastic Lake, Ontario

    Directory of Open Access Journals (Sweden)

    J. Aherne

    2007-09-01

    Full Text Available Climate-induced drought events have a significant influence on sulphate export from forested catchments in central Ontario, subsequently delaying the recovery of surface waters from acidification. In the current study, a model chain that employed a statistical downscaling model, a hydrological model and two hydrochemical models was used to forecast the chemical recovery of Plastic Lake sub-catchment 1 (PC1 from acidification under proposed deposition reductions and the A2 emission scenario of the Intergovernmental Panel on Climate Change. Any predicted recovery in stream acid neutralising capacity and pH owing to deposition reductions were clearly offset by large acid effluxes from climate-induced drought events. By 2100, ANC is predicted to show large variations ranging between 10 and −30 μmolc L−1. Similarly, predicted pH in 2100 is lower (>0.05 of a pH unit than the value simulated for 2000 (pH 4.35. Despite emission reductions, the future scenario paints a bleak picture of reacidification at PC1 to levels commensurate with those of the late 1970s. The principal process behind this reacidification is the oxidation of previously stored (reduced sulphur compounds in wetlands during periods of low-flow (or drought, with subsequent efflux of sulphate upon re-wetting. Simulated catchment runoff under the A2 emissions scenario predictes increased intensity and frequency of low-flow events from approximately 2030 onwards. The Integrated Catchments model for Carbon indicated that stream DOC concentrations at PC1 will also increase under the future climate scenario, with temperature being the principal driver. Despite the predicted (significant increase in DOC, pH is not predicted to further decline (beyond the climate-induced oxidation scenario, instead pH shows greater variability throughout the simulation. As echoed by many recent studies, hydrochemical models and model frameworks need to incorporate the drivers

  3. Oxidative coulometric trace determination of sulphur in hydrocarbons.

    Science.gov (United States)

    Cedergren, A

    1973-07-01

    A new combustion system for the oxidative coulometric determination of sulphur in liquid hydrocarbons is described. The conditions were selected so that the recovery as SO(2) was close to 100%. The relative standard deviation was < 1% for sulphur in the range 2-1000 mg/l., with thiophene in cyclohexane as a test substance. Thermodynamic data on the equilibrium between SO(2), O(2) and SO(3) were used to select the operating conditions. To increase the recovery of SO(2) the combustion gas mixture was diluted with an inert gas to lower the partial pressure of oxygen. A temperature of 1000 degrees in the equilibrium zone resulted in a recovery of 99%. The SO(2) was titrated with coulometrically generated iodine, the concentration of which was controlled by a Pt-redox electrode. The response of this electrode has been examined. A rather high concentration of I(-) was used to suppress iodine losses during the analysis. The time of analysis was 2-5 min, and sample sizes were 3-7 mul. An LKB 16300 Coulometric Analyzer governed the titration procedure.

  4. Potential influence of sulphur bacteria on Palaeoproterozoic phosphogenesis

    Science.gov (United States)

    Lepland, Aivo; Joosu, Lauri; Kirsimäe, Kalle; Prave, Anthony R.; Romashkin, Alexander E.; Črne, Alenka E.; Martin, Adam P.; Fallick, Anthony E.; Somelar, Peeter; Üpraus, Kärt; Mänd, Kaarel; Roberts, Nick M. W.; van Zuilen, Mark A.; Wirth, Richard; Schreiber, Anja

    2014-01-01

    All known forms of life require phosphorus, and biological processes strongly influence the global phosphorus cycle. Although the record of life on Earth extends back to 3.8billion years ago and the advent of biological phosphate processing can be tracked to at least 3.5billion years ago, the earliest known P-rich deposits appeared only 2billion years ago. The onset of P deposition has been attributed to the rise of atmospheric oxygen 2.4-2.3billion years ago and the related profound biogeochemical shifts, which increased the riverine input of phosphate to the ocean and boosted biological productivity and phosphogenesis. However, the P-rich deposits post-date the rise of oxygen by about 300million years. Here we use microfabric, trace element and carbon isotope analyses to assess the environmental setting and redox conditions of the 2-billion-year-old P-rich deposits of the vent- or seep-influenced Zaonega Formation, northwest Russia. We identify phosphatized microorganism fossils that resemble modern methanotrophic archaea and sulphur-oxidizing bacteria, analogous to organisms found in modern seep settings and upwelling zones with a sharp redoxcline. We therefore propose that the P-rich deposits in the Zaonega Formation were formed by phosphogenesis mediated by sulphur bacteria, similar to modern sites, and by the precipitation of calcium phosphate minerals on microbial templates during early diagenesis.

  5. Sulphur chemistry in the envelopes of massive young stars

    CERN Document Server

    Van der Tak, F F S; Van Dishoeck, E F

    2002-01-01

    We present submillimeter observations of SO, SO2, H2S, H2CS, OCS, NS and HCS+ toward nine massive young stars. The outflow contributes ~50% to the SO and SO2 emission in 15-20'' beams, more than for CS, where it is 10%. The SO2 abundance increases from dark cloud levels in the outer envelope (T100 K). Molecular abundances are consistent with a model of ice evaporation in an envelope with gradients in temperature and density for a chemical age of ~30000 yr. The high observed abundance of OCS, the fact that T_ex (OCS) >> T_ex (H2S), and the data on solid OCS and H2S all suggest that the major sulphur carrier in grain mantles is OCS rather than H2S. For most other sulphur-bearing molecules, the source-to-source abundance variations by factors of up to 10 do not correlate with previously established evolutionary trends in temperature tracers. These species probe the chemically inactive outer envelope. Our data set does not constrain the abundances of H2S and SO in the inner envelope, which, together with SO2, are...

  6. Effect of acetic acid in recycling water on ethanol production for cassava in an integrated ethanol-methane fermentation process.

    Science.gov (United States)

    Yang, Xinchao; Wang, Ke; Zhang, Jianhua; Tang, Lei; Mao, Zhonggui

    2016-11-01

    Recently, the integrated ethanol-methane fermentation process has been studied to prevent wastewater pollution. However, when the anaerobic digestion reaction runs poorly, acetic acid will accumulate in the recycling water. In this paper, we studied the effect of low concentration of acetic acid (≤25 mM) on ethanol fermentation at different initial pH values (4.2, 5.2 or 6.2). At an initial pH of 4.2, ethanol yields increased by 3.0% and glycerol yields decreased by 33.6% as the acetic acid concentration was increased from 0 to 25 mM. Raising the concentration of acetic acid to 25 mM increased the buffering capacity of the medium without obvious effects on biomass production in the cassava medium. Acetic acid was metabolized by Saccharomyces cerevisiae for the reason that the final concentration of acetic acid was 38.17% lower than initial concentration at pH 5.2 when 25 mM acetic acid was added. These results confirmed that a low concentration of acetic acid in the process stimulated ethanol fermentation. Thus, reducing the acetic acid concentration to a controlled low level is more advantageous than completely removing it.

  7. Copper recovery from gold contained sulphuric slag by acid leaching —Industrial production practices of gold recovery by CIP%含金硫酸烧渣酸浸铜—氰化炭浆法提金工艺生产实践

    Institute of Scientific and Technical Information of China (English)

    张静茹; 李晓文

    2012-01-01

    Bench scale tests on cyanidation - CIP process to leach gold and the industrial production practices indicate that it is technically viable to use CIP to deal with gold contained sulphuric slag. It not only achieves satisfactory technical indexes but also saves the infrastructural construction investment and shortens the construction term. The hematite content in the slag has less than considerable impact on the carbon adsorption.%陕西省某黄金冶炼厂含金硫酸烧渣酸浸铜—氰化炭浆法提金工艺的小型试验及工业生产实践的结果表明:采用炭浆法处理含金硫酸烧渣在技术上是可行的,不仅可以取得较好的技术指标,而且可以节省基建投资和缩短基建工期.含金硫酸烧渣中的赤铁矿对活性炭影响不大.

  8. Circulating nucleic acids damage DNA of healthy cells by integrating into their genomes

    Indian Academy of Sciences (India)

    Indraneel Mittra; Naveen Kumar Khare; Gorantla Venkata Raghuram; Rohan Chaubal; Fatema Khambatti; Deepika Gupta; Ashwini Gaikwad; Preeti Prasannan; Akshita Singh; Aishwarya Iyer; Ankita Singh; Pawan Upadhyay; Naveen Kumar Nair; Pradyumna Kumar Mishra; Amit Dutt

    2015-03-01

    Whether nucleic acids that circulate in blood have any patho-physiological functions in the host have not been explored. We report here that far from being inert molecules, circulating nucleic acids have significant biological activities of their own that are deleterious to healthy cells of the body. Fragmented DNA and chromatin (DNAfs and Cfs) isolated from blood of cancer patients and healthy volunteers are readily taken up by a variety of cells in culture to be localized in their nuclei within a few minutes. The intra-nuclear DNAfs and Cfs associate themselves with host cell chromosomes to evoke a cellular DNA-damage-repair-response (DDR) followed by their incorporation into the host cell genomes. Whole genome sequencing detected the presence of tens of thousands of human sequence reads in the recipient mouse cells. Genomic incorporation of DNAfs and Cfs leads to dsDNA breaks and activation of apoptotic pathways in the treated cells. When injected intravenously into Balb/C mice, DNAfs and Cfs undergo genomic integration into cells of their vital organs resulting in activation of DDR and apoptotic proteins in the recipient cells. Cfs have significantly greater activity than DNAfs with respect to all parameters examined, while both DNAfs and Cfs isolated from cancer patients are more active than those from normal volunteers. All the above pathological actions of DNAfs and Cfs described above can be abrogated by concurrent treatment with DNase I and/or anti-histone antibody complexed nanoparticles both in vitro and in vivo. Taken together, our results that circulating DNAfs and Cfs are physiological, continuously arising, endogenous DNA damaging agents with implications to ageing and a multitude of human pathologies including initiation of cancer.

  9. Transport of metals and sulphur in magmas by flotation of sulphide melt on vapour bubbles

    Science.gov (United States)

    Mungall, J. E.; Brenan, J. M.; Godel, B.; Barnes, S. J.; Gaillard, F.

    2015-03-01

    Emissions of sulphur and metals from magmas in Earth’s shallow crust can have global impacts on human society. Sulphur-bearing gases emitted into the atmosphere during volcanic eruptions affect climate, and metals and sulphur can accumulate in the crust above a magma reservoir to form giant copper and gold ore deposits, as well as massive sulphur anomalies. The volumes of sulphur and metals that accumulate in the crust over time exceed the amounts that could have been derived from an isolated magma reservoir. They are instead thought to come from injections of multiple new batches of vapour- and sulphide-saturated magmas into the existing reservoirs. However, the mechanism for the selective upward transfer of sulphur and metals is poorly understood because their main carrier phase, sulphide melt, is dense and is assumed to settle to the bottoms of magma reservoirs. Here we use laboratory experiments as well as gas-speciation and mass-balance models to show that droplets of sulphide melt can attach to vapour bubbles to form compound drops that float. We demonstrate the feasibility of this mechanism for the upward mobility of sulphide liquids to the shallow crust. Our work provides a mechanism for the atmospheric release of large amounts of sulphur, and contradicts the widely held assumption that dense sulphide liquids rich in sulphur, copper and gold will remain sequestered in the deep crust.

  10. Nickel boride: An improved desulphurizing agent for sulphur-rich geomacromolecules in polar and asphaltene fractions

    NARCIS (Netherlands)

    Sinninghe Damsté, J.S.; Schouten, S.; Pavlovic, D.; Leeuw, J.W. de

    1993-01-01

    Nickel boride, a novel desulphurizing agent, was investigated for the desulphurization of sulphur-rich geomacromolecules in polar and asphaltene fractions. It was found to be as effective as the conventional desulphurizing agent, Raney nickel, for sulphur-rich geomacromolecules in polar fractions, b

  11. THE SEVERAL SPECIAL USES OF SULPHUR%硫磺的几种专门应用

    Institute of Scientific and Technical Information of China (English)

    胡文宾; 高淑美; 郝国阳; 唐昭峥

    2000-01-01

    With the improvement of processing amount of sour crude and the development of deep processing of crude oil, the sulphur production was increasing every day. It was very important to explore the new way out of sulphur and develop the use of sulphur. The sulphur had wild application in the industry of agriculture, medicine, rubber, building material and powder. The special uses of sulphur combining the developing conditions at home and abroad, especially including insoluble sulphur, sulphur coated urea, sulphur concrete, sodium sulfur battery were introduced.%随着含硫原油加工量的增加和原油深度加工的发展,硫磺的产量日益增加,探索硫磺产品的出路并开发新的用途显得日益重要。硫磺广泛应用于农业、医药、橡胶、建材、火药等行业,其中专用硫磺在国民经济中占有特殊地位,本文结合国内外的发展情况,介绍了硫磺的几种专门应用,主要包括聚合硫、硫磺尿素、硫磺混凝土和Na-S电池的开发。

  12. 78 FR 64526 - Information Collection Activities: Sulphur Operations; Submitted for Office of Management and...

    Science.gov (United States)

    2013-10-29

    ...; 134E1700D2 EEEE500000 ET1SF0000.DAQ000] Information Collection Activities: Sulphur Operations; Submitted for Office of Management and Budget (OMB) Review; Comment Request ACTION: 30-day Notice. SUMMARY: To comply... regulations under Subpart P, Sulphur Operations. This notice also provides the public a second opportunity...

  13. Chelated Nitrogen-Sulphur-Codoped TiO2: Synthesis, Characterization, Mechanistic, and UV/Visible Photocatalytic Studies

    Directory of Open Access Journals (Sweden)

    Hayat Khan

    2017-01-01

    Full Text Available This study presents in detail the physicochemical, photoluminescent, and photocatalytic properties of carboxylic acid chelated nitrogen-sulphur-codoped TiO2. From the Fourier transform infrared spectroscopic study, it was revealed that the formate group formed bidentate bridging linkage while the acetate group coordinated in a bidentate chelating mode with a titanium precursor. In compliance with X-ray diffraction data, the anatase to rutile transformation temperature was extended due to carboxylic acid chelation and NS codoping. Raman analysis indicated four Raman peaks at 146, 392, 512, and 632 cm−1 for the precalcined chelated TiO2; on incorporation with NS dopants, an increase in Raman intensity for these peaks was recorded, indicating the structure stability of the anatase phase. Furthermore, X-ray photoelectron spectroscopic study revealed the presence of anionic doping of nitrogen and cationic doping of sulphur in the lattice of TiO2. When evaluating the UV-visible photodegradation rate of 4-chlorophenol, the modified TiO2 (NS0.06-TFA showed the highest photocatalytic activity. In connection with the activity tests, several scavenger agents were employed to elucidate the significance of the different reactive oxidizing species during the photocatalytic process. Moreover, the transfer pathways of photogenerated carriers and the photocatalytic reaction mechanism of modified TiO2 were also explained in detail.

  14. Integration

    DEFF Research Database (Denmark)

    Emerek, Ruth

    2004-01-01

    Bidraget diskuterer de forskellige intergrationsopfattelse i Danmark - og hvad der kan forstås ved vellykket integration......Bidraget diskuterer de forskellige intergrationsopfattelse i Danmark - og hvad der kan forstås ved vellykket integration...

  15. Three-decade changes in chemical composition of precipitation in Guangzhou city, southern China: has precipitation recovered from acidification following sulphur dioxide emission control?

    Directory of Open Access Journals (Sweden)

    Yunting Fang

    2013-09-01

    Full Text Available We examined if precipitation had recovered from acidification in Guangzhou, the third biggest city in China, and if sulphur deposition in precipitation had decreased, and to what extent if yes, following abatement strategies in sulphur dioxide (SO2 emission and energy use implemented since 2001. SO2 emissions were decreasing steadily since 2001, but a marked recovery of precipitation acidity occurred only since 2005; precipitation pH values decreased from 4.65 in 2001 to 4.34 in 2005 and then increased to 5.08 in 2010, while in the same period acid rain (pH<5.6 frequency increased from 70% to 81% and then decreased to 48%. During this period, the change in pH value and sulphate concentration more reflected the patterns of SO2 emission at provincial and national scales than at the local scale, suggesting that precipitation chemical composition was largely controlled by the emissions of pollutants from surrounding areas of the study city. Since 2001, sulphate deposition in precipitation decreased significantly (by 40% but nitrogen deposition remained unaltered. More importantly, the current sulphur (43 kg S ha−1 yr−1 as sulphate and nitrogen depositions (35 kg N ha−1 yr−1 as ammonium plus nitrate in 2010 were still among the highest in China. These results highlight the fact that ambient sulphur and nitrogen deposition still pose a threat to the health of both terrestrial and aquatic ecosystems. Precipitation may become more acidified in the future because the deposition of alkaline dusts containing calcium is also likely to decrease with stricter SO2 emission control policy and reduced construction activities. Additionally, we recommend that a reduction of emissions of nitrogen and chlorine bearing pollutants is urgently required for complete control on acid deposition.

  16. Long-life Li/polysulphide batteries with high sulphur loading enabled by lightweight three-dimensional nitrogen/sulphur-codoped graphene sponge

    Science.gov (United States)

    Zhou, Guangmin; Paek, Eunsu; Hwang, Gyeong S.; Manthiram, Arumugam

    2015-07-01

    Lithium-sulphur batteries with a high theoretical energy density are regarded as promising energy storage devices for electric vehicles and large-scale electricity storage. However, the low active material utilization, low sulphur loading and poor cycling stability restrict their practical applications. Herein, we present an effective strategy to obtain Li/polysulphide batteries with high-energy density and long-cyclic life using three-dimensional nitrogen/sulphur codoped graphene sponge electrodes. The nitrogen/sulphur codoped graphene sponge electrode provides enough space for a high sulphur loading, facilitates fast charge transfer and better immobilization of polysulphide ions. The hetero-doped nitrogen/sulphur sites are demonstrated to show strong binding energy and be capable of anchoring polysulphides based on first-principles calculations. As a result, a high specific capacity of 1,200 mAh g-1 at 0.2C rate, a high-rate capacity of 430 mAh g-1 at 2C rate and excellent cycling stability for 500 cycles with ~0.078% capacity decay per cycle are achieved.

  17. Acid/base switching of the tautomerism and conformation of a dioxoporphyrin for integrated binary subtraction.

    Science.gov (United States)

    Ding, Yubin; Li, Xin; Hill, Jonathan P; Ariga, Katsuhiko; Agren, Hans; Andréasson, Joakim; Zhu, Weihong; Tian, He; Xie, Yongshu

    2014-09-26

    Compared with most of the reported logic devices based on the supramolecular approach, systems based on individual molecules can avoid challenging construction requirements. Herein, a novel dioxoporphyrin DPH22 was synthesized and two of its tautomers were characterized by single-crystal X-ray diffraction studies. Compound DPH22 exhibits multichannel controllable stepwise tautomerization, protonation, and deprotonation processes through interactions with H(+) and F(-) ions. By using the addition of H(+) and F(-) ions as inputs and UV/Vis absorption values at λ=412, 510, 562, and 603 nm as outputs, the controlled tautomerism of DPH22 has been successfully used for the construction of an integrated molecular level half-subtractor and comparator. In addition, this acid/base-switched tautomerism is reversible, thus endowing the system with ease of reset and recycling; consequently, there is no need to modulate complicated intermolecular interactions and electron-/charge-transfer processes. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  18. Nacre-inspired integrated strong and tough reduced graphene oxide-poly(acrylic acid) nanocomposites

    Science.gov (United States)

    Wan, Sijie; Hu, Han; Peng, Jingsong; Li, Yuchen; Fan, Yuzun; Jiang, Lei; Cheng, Qunfeng

    2016-03-01

    Inspired by the relationship between interface interactions and the high performance mechanical properties of nacre, a strong and tough nacre-inspired nanocomposite was demonstrated based on graphene oxide (GO) and polyacrylic acid (PAA) prepared via a vacuum-assisted filtration self-assembly process. The abundant hydrogen bonding between GO and PAA results in both high strength and toughness of the bioinspired nanocomposites, which are 2 and 3.3 times higher than that of pure reduced GO film, respectively. In addition, the effect of environmental relative humidity on the mechanical properties of bioinspired nanocomposites is also investigated, and is consistent with previous theoretical predictions. Moreover, this nacre-inspired nanocomposite also displays high electrical conductivity of 108.9 S cm-1. These excellent physical properties allow this type of nacre-inspired nanocomposite to be used in many applications, such as flexible electrodes, aerospace applications, and artificial muscles etc. This nacre-inspired strategy also opens an avenue for constructing integrated high performance graphene-based nanocomposites in the near future.

  19. The implications of the new sulphur limits on the European Ro-Ro sector

    DEFF Research Database (Denmark)

    Zis, Thalis; Psaraftis, Harilaos N.

    2017-01-01

    In an effort to reduce the environmental impacts of maritime transportation, the International Maritime Organization (IMO) designated special Sulphur Emission Control Areas (SECAs) where ships are required to use low-sulphur fuel. In January 2015, the sulphur limit within SECAs was lowered to 0......-based alternatives. The exact repercussions of the new sulphur limits are difficult to identify in the wake of significant recent reductions of the fuel prices for both low-sulphur and heavy fuel oil. This paper presents a modal split model that estimates modal shifts vis-a-vis competing maritime and land...... and the redistribution of transport. Recommendations to mitigate and reverse the negative side-effects of such environmental legislation are proposed....

  20. The implications of the new sulphur limits on the European Ro-Ro sector

    DEFF Research Database (Denmark)

    Zis, Thalis; Psaraftis, Harilaos N.

    In an effort to reduce the environmental impacts of maritime transportation, the International Maritime Organization (IMO) designated special Sulphur Emission ControlAreas (SECAs) where ships are required to use low-sulphur fuel. In January 2015, the sulphur limit within SECAs was lowered to 0......-based alternatives. The exact repercussions of the new sulphur limits are difficult to identify in the wake of significant recent reductions of the fuel prices for both low-sulphur and heavy fuel oil. This paper presents a modal split model that estimates modal shifts vis-a-vis competing maritime and land...... and the redistribution of transport. Recommendations to mitigate and reverse the negative side-effects of such environmental legislation are proposed....

  1. Polyimido sulphur anions S(NR)$^{m-}_{n}$: Free radicals and coordination behaviour

    Indian Academy of Sciences (India)

    Dietmar Stalke

    2000-06-01

    In a reaction sequence of amide addition followed by halogen oxidation the triazasulphite S(NR)$^{2-}_{3}$ and the tetrazasulphate S(NR)$^{2-}_{4}$ are readily accessible from sulphur diimide S(NR)2 via sulphur triimide S(NR)3. Addition of lithium organics to sulphur triimide provides a general route to triazasulphonates RS(NR)$^{2-}_{3}$. All these anions resemble potential tripodal coordination behaviour because of their nitrogen donor centres. Furthermore, the sulphur polyimido ligands are capable of responding to the various requirements of different metals (even in mixed metal species) by charge (de)localization. This paper deals with the synthetic routes of the sulphur nitrogen anions and their coordination behaviour. Their reactivity, mainly towards main group metal synthons, is also discussed.

  2. Reduction of Sulphur-containing Aromatic Nitro Compounds with Hydrazine Hydrate over Iron(Ⅲ) Oxide-MgO Catalyst

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Sulphur-containing aromatic amines were prepared efficiently in good to excellent yields by reduction of the corresponding sulphur-containing aromatic nitro compounds with hydrazine hydrate in the presence of iron(Ⅲ) oxide-MgO catalyst. The catalyst exhibited high activity and stability for the reduction of sulphur-containing aromatic nitro compounds. The yields of sulphur-containing aromatic amines were up to 91-99 % at 355 K after reduction for 1-4 h over this catalyst.

  3. Identification and distribution of sulfate reducing bacteria and sulphur-oxidising bacteria in northern South China Sea

    Science.gov (United States)

    Mao, S.; Zhu, X.; Guan, H.; Wu, D.; Wu, N.

    2015-12-01

    Fatty acids are one of the major components in modern marine sediments. It is well known that the saturated short-chain FAs were typically to be from vascular plants, algae, bacteria, and other sources, while the saturated long-chain FAs are the major components found in leaf waxes, suberin, and cutin in terrestrial higher plants. So the lipid biomarkers of fatty acids in Site 4B from Shenhu Area, northern South China Sea were investigated in Recent research supported from the 973 Program (2009CB219506), and the resources of branched fatty acids and monounsaturated fatty acids were mainly discussed. The results reveal that i/a15:0, i/a17:0, 16:1ω5, 18:1ω9 and 10me16:0 are derived from sulfate reducing bacteria (SRB), while 16:1ω7t/c and 18:1ω7 are originated from sulphur-oxidising bacteria (SOB). The biomakers of methanotrophs such as 16:1ω6/8 and 18:1ω6/8 were not detected in the sediments which coincide with more positive carbon isotope values of the fatty acids in the sediments. The stable relationship between SRB and SOB below 97cm in the sediments reflects the relative stable oxidative and reductive depositional environment which may be connected with the sulphur cycle in the sediments, that is carried out as sulfate is reduced to sulfide, and then sulfide is oxidized to sulfate and elemental sulfur, at last elemental sulfur is disproportionated to sulfide and sulfate. The frequently changed relationship of SRB and SOB above 97cm in the sediments indicates intensely changing oxidative and reductive sedimental environment, that may related with diapir structure around Site 4B, which also brings about hydrocarbon seepage leading to increasing biomass at 97cm.

  4. Spatial distributions of sulphur species and sulphate-reducing bacteria provide insights into sulphur redox cycling and biodegradation hot-spots in a hydrocarbon-contaminated aquifer

    Science.gov (United States)

    Einsiedl, Florian; Pilloni, Giovanni; Ruth-Anneser, Bettina; Lueders, Tillman; Griebler, Christian

    2015-05-01

    Dissimilatory sulphate reduction (DSR) has been proven to be one of the most relevant redox reactions in the biodegradation of contaminants in groundwater. However, the possible role of sulphur species of intermediate oxidation state, as well as the role of potential re-oxidative sulphur cycling in biodegradation particularly at the groundwater table are still poorly understood. Here we used a combination of stable isotope measurements of SO42-, H2S, and S0 as well as geochemical profiling of sulphur intermediates with special emphasis on SO32-, S2O32-, and S0 to unravel possible sulphur cycling in the biodegradation of aromatics in a hydrocarbon-contaminated porous aquifer. By linking these results to the quantification of total bacterial rRNA genes and respiratory genes of sulphate reducers, as well as pyrotag sequencing of bacterial communities over depth, light is shed on possible key-organisms involved. Our results substantiate the role of DSR in biodegradation of hydrocarbons (mainly toluene) in the highly active plume fringes above and beneath the plume core. In both zones the concentration of sulphur intermediates (S0, SO32- and S2O32-) was almost twice that of other sampling-depths, indicating intense sulphur redox cycling. The dual isotopic fingerprint of oxygen and sulphur in dissolved sulphate suggested a re-oxidation of reduced sulphur compounds to sulphate especially at the upper fringe zone. An isotopic shift in δ34S of S0 of nearly +4‰ compared to the δ34S values of H2S from the same depth linked to a high abundance (∼10%) of sequence reads related to Sulphuricurvum spp. (Epsilonproteobacteria) in the same depth were indicative of intensive oxidation of S0 to sulphate in this zone. At the lower plume fringe S0 constituted the main inorganic sulphur species, possibly formed by abiotic re-oxidation of H2S with Fe(III)oxides subsequent to sulphate reduction. These results provide first insights into intense sulphur redox cycling in a hydrocarbon

  5. 76 FR 52963 - Information Collection Activity: Prospecting for Minerals Other Than Oil, Gas, and Sulphur on the...

    Science.gov (United States)

    2011-08-24

    ...: Prospecting for Minerals Other Than Oil, Gas, and Sulphur on the Outer Continental Shelf, Revision of a... for Minerals Other than Oil, Gas, and Sulphur on the Outer Continental Shelf (OMB No. 1010-0072), and... Minerals Other than Oil, Gas, and Sulphur on the Outer Continental Shelf. BOEMRE Form(s): 0134. OMB...

  6. Structural enzymology of sulphur metabolism in Mycobacterium tuberculosis.

    Science.gov (United States)

    Schnell, Robert; Schneider, Gunter

    2010-05-21

    The emergence of multidrug-resistant strains of Mycobacterium tuberculosis poses a serious threat to human health and has led to world-wide efforts focusing on the development of novel vaccines and antibiotics against this pathogen. Sulphur metabolism in this organism has been linked to essential processes such as virulence and redox defence. The cysteine biosynthetic pathway is up-regulated in models of persistent M. tuberculosis infections and provides potential targets for novel anti-mycobacterial agents, directed specifically toward the pathogen in its persistent phase. Functional and structural characterization of enzymes from sulfur metabolism establishes a necessary framework for the design of strong binding inhibitors that might be developed into new drugs. This review summarizes recent progress in the elucidation of the structural enzymology of the sulphate reduction and cysteine biosynthesis pathways.

  7. [Integrity].

    Science.gov (United States)

    Gómez Rodríguez, Rafael Ángel

    2014-01-01

    To say that someone possesses integrity is to claim that that person is almost predictable about responses to specific situations, that he or she can prudentially judge and to act correctly. There is a closed interrelationship between integrity and autonomy, and the autonomy rests on the deeper moral claim of all humans to integrity of the person. Integrity has two senses of significance for medical ethic: one sense refers to the integrity of the person in the bodily, psychosocial and intellectual elements; and in the second sense, the integrity is the virtue. Another facet of integrity of the person is la integrity of values we cherish and espouse. The physician must be a person of integrity if the integrity of the patient is to be safeguarded. The autonomy has reduced the violations in the past, but the character and virtues of the physician are the ultimate safeguard of autonomy of patient. A field very important in medicine is the scientific research. It is the character of the investigator that determines the moral quality of research. The problem arises when legitimate self-interests are replaced by selfish, particularly when human subjects are involved. The final safeguard of moral quality of research is the character and conscience of the investigator. Teaching must be relevant in the scientific field, but the most effective way to teach virtue ethics is through the example of the a respected scientist.

  8. Long-term sedimentary recycling of rare sulphur isotope anomalies.

    Science.gov (United States)

    Reinhard, Christopher T; Planavsky, Noah J; Lyons, Timothy W

    2013-05-01

    The accumulation of substantial quantities of O2 in the atmosphere has come to control the chemistry and ecological structure of Earth's surface. Non-mass-dependent (NMD) sulphur isotope anomalies in the rock record are the central tool used to reconstruct the redox history of the early atmosphere. The generation and initial delivery of these anomalies to marine sediments requires low partial pressures of atmospheric O2 (p(O2); refs 2, 3), and the disappearance of NMD anomalies from the rock record 2.32 billion years ago is thought to have signalled a departure from persistently low atmospheric oxygen levels (less than about 10(-5) times the present atmospheric level) during approximately the first two billion years of Earth's history. Here we present a model study designed to describe the long-term surface recycling of crustal NMD anomalies, and show that the record of this geochemical signal is likely to display a 'crustal memory effect' following increases in atmospheric p(O2) above this threshold. Once NMD anomalies have been buried in the upper crust they are extremely resistant to removal, and can be erased only through successive cycles of weathering, dilution and burial on an oxygenated Earth surface. This recycling results in the residual incorporation of NMD anomalies into the sedimentary record long after synchronous atmospheric generation of the isotopic signal has ceased, with dynamic and measurable signals probably surviving for as long as 10-100 million years subsequent to an increase in atmospheric p(O2) to more than 10(-5) times the present atmospheric level. Our results can reconcile geochemical evidence for oxygen production and transient accumulation with the maintenance of NMD anomalies on the early Earth, and suggest that future work should investigate the notion that temporally continuous generation of new NMD sulphur isotope anomalies in the atmosphere was likely to have ceased long before their ultimate disappearance from the rock record.

  9. Comparative study on sulphur reduction from heavy petroleum - Solvent extraction and microwave irradiation approach

    Energy Technology Data Exchange (ETDEWEB)

    Mohammed, Abdullahi Dyadya; Isah, Abubakar Garba; Umaru, Musa; Ahmed, Shehu [Department of Chemical Engineering, Federal University of Technology, P.M.B 65, Minna (Nigeria); Abdullahi, Yababa Nma [National Petroleum Investment Management Services (Nigeria National Petroleum Corporation), Lagos (Nigeria)

    2012-07-01

    Sulphur- containing compounds in heavy crude oils are undesirable in refining process as they affect the quality of the final product, cause catalyst poisoning and deactivation in catalytic converters as well as causing corrosion problems in oil pipelines, pumps and refining equipment aside environmental pollution from their combustion and high processing cost. Sulphur reduction has being studied using microwave irradiation set at 300W for 10 and 15minutes and oxidative- solvent extraction method using n- heptane and methanol by 1:1, 1:2 and 1:3 crude- solvent ratios after being oxidized with hydrogen peroxide, H2O2 oxidants. Percentage sulphur removal with n- heptane solvent by 1:1 and 1:2 are 81.73 and 85.47%; but extraction using methanol by different observed ratios gave less sulphur reduction. Indeed when microwave irradiated at 300W for 10 and 15minutes, 53.68 and 78.45% reduction were achieved. This indicates that microwave irradiation had caused oxidation by air in the oven cavity and results to formation of alkyl radicals and sulphoxide from sulphur compound in the petroleum. The prevailing sulphur found in the crude going by FT-IR results is sulphides which oxidized to sulphoxide or sulphones. It is clear that sulphur extraction with heptane is more efficient than microwave irradiation but economically due to demands for solvent and its industrial usage microwave irradiation can serve as alternative substitute for sulphur reduction in petroleum. Sulphur reduction by microwave radiation should be up- scaled from laboratory to a pilot plant without involving extraction column in the refining.

  10. Comparative study on sulphur reduction from heavy petroleum - Solvent extraction and microwave irradiation approach

    Directory of Open Access Journals (Sweden)

    Abdullahi Dyadya Mohammed, Abubakar Garba Isah, Musa Umaru, Shehu Ahmed, Yababa Nma Abdullahi

    2012-01-01

    Full Text Available Sulphur- containing compounds in heavy crude oils are undesirable in refining process as they affect the quality of the final product, cause catalyst poisoning and deactivation in catalytic converters as well as causing corrosion problems in oil pipelines, pumps and refining equipment aside environmental pollution from their combustion and high processing cost. Sulphur reduction has being studied using microwave irradiation set at 300W for 10 and 15minutes and oxidative- solvent extraction method using n- heptane and methanol by 1:1, 1:2 and 1:3 crude- solvent ratios after being oxidized with hydrogen peroxide, H2O2 oxidants. Percentage sulphur removal with n- heptane solvent by 1:1 and 1:2 are 81.73 and 85.47%; but extraction using methanol by different observed ratios gave less sulphur reduction. Indeed when microwave irradiated at 300W for 10 and 15minutes, 53.68 and 78.45% reduction were achieved. This indicates that microwave irradiation had caused oxidation by air in the oven cavity and results to formation of alkyl radicals and sulphoxide from sulphur compound in the petroleum. The prevailing sulphur found in the crude going by FT-IR results is sulphides which oxidized to sulphoxide or sulphones. It is clear that sulphur extraction with heptane is more efficient than microwave irradiation but economically due to demands for solvent and its industrial usage microwave irradiation can serve as alternative substitute for sulphur reduction in petroleum. Sulphur reduction by microwave radiation should be up- scaled from laboratory to a pilot plant without involving extraction column in the refining.

  11. Geological controls on the sulphur content of coal seams in the Northumberland Coalfield, Northeast England

    Energy Technology Data Exchange (ETDEWEB)

    Turner, Brian R. [Department of Earth Sciences, Science Laboratories, University of Durham, South Road, Durham DH1 3LE (United Kingdom); Richardson, David [H.J. Banks and Co. Ltd, Bishop Auckland DL13 4HG (United Kingdom)

    2004-12-03

    The sulphur content of coal is an important consideration when developing reserves for exploitation, driven by emission limits from power stations becoming more stringent. Variations in the sulphur content of Westphalian A and B coals from the predominantly freshwater Northumberland Coalfield, Northeast England, were studied according to their regional, stratigraphic and in-seam location. The observed variation in sulphur content spatially increases towards the source area away from more marine influenced areas, with increased sulphur content through time linked to changes in the general depositional environment as conditions became more marine-influenced. A model of basinal surface water and groundwater flow driven by post-depositional source area tectonism is thought to have played only a minor role in contributing secondary sulphur to the coal. However, the isotopic composition of coal pyrite shows a similar range in composition to that of pyrite and other sulphides from the North Pennine Orefield along the southern margin of the coalfield, suggesting an additional potential source of secondary sulphur, as sulphur-rich fluids were expelled northwards through the coal measures during early Permian Variscan transpression from the south. The Westphalian A and B are interpreted as third-order depositional sequences, defined by third-order maximum flooding surfaces. Each sequence is made up of several coal-bearing fourth-order parasequences, which tend to be more brackish to marine in character, on either side of the third-order maximum flooding surfaces when base level was relatively high. The lowest sulphur coals are confined to the lower to middle, relative low stand part of the Westphalian A third-order base level curve and the lowest part of the Westphalian B third-order base level curve. This difference is attributed to a more rapid rise of base level in the Westphalian B. The stratigraphic and spatial distribution of coal sulphur has been used as a guide to

  12. Natural oils affect the human skin integrity and the percutaneous penetration of benzoic acid dose-dependently

    DEFF Research Database (Denmark)

    Nielsen, Jesper Bo

    2006-01-01

    Abstract: Natural oils are extensively used in cosmetics and as treatment for a growing number of more or less specific ailments. Skin irritation and cases of allergy have repeatedly been described in the literature following exposure to these oils. The present study evaluated the extent to which...... three natural oils (eucalyptus oil, tea tree oil, peppermint oil) would affect the skin integrity and the percutaneous penetration of benzoic acid when applied topically in relevant concentrations. An experimental in vitro model using static diffusion cells mounted with human breast or abdominal skin...... was applied. The three natural oils decreased the skin integrity dose-dependently. Concomitant dermal exposure to low concentrations of peppermint oil reduced the percutaneous penetration of benzoic acid. The present study lends support to the notion that low concentrations of peppermint oil may act...

  13. Substrate integrated Lead-Carbon hybrid ultracapacitor with flooded, absorbent glass mat and silica-gel electrolyte configurations

    OpenAIRE

    Banerjee, A.; Ravikumar, MK; Jalajakshi, A; Kumar, Suresh P; Gaffoor, SA; Shukla, AK

    2012-01-01

    Lead-Carbon hybrid ultracapacitors (Pb-C HUCs) with flooded, absorbent-glass-mat (AGM) and silica-gel sulphuric acid electrolyte configurations are developed and performance tested. Pb-C HUCs comprise substrate-integrated PbO2 (SI-PbO2) as positive electrodes and high surface-area carbon with graphite-sheet substrate as negative electrodes. The electrode and silica-gel electrolyte materials are characterized by XRD, XPS, SEM, TEM, Rheometry, BET surface area, and FTIR spectroscopy in conjunct...

  14. Enhanced lithium ion storage in TiO2 nanoparticles, induced by sulphur and carbon co-doping

    Science.gov (United States)

    Ivanov, Svetlozar; Barylyak, Adriana; Besaha, Khrystyna; Dimitrova, Anna; Krischok, Stefan; Bund, Andreas; Bobitski, Jaroslav

    2016-09-01

    Sulphur and carbon codoped anatase nanoparticles are synthesized by one-step approach based on interaction between thiourea and metatitanic acid. Electron microscopy shows micrometer-sized randomly distributed crystal aggregates, consisting of many 25-40 nm TiO2 nanoparticles. The obtained phase composition and chemical states of the elements in the structure are analyzed by means of X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). XRD shows that after doping the tetragonal anatase structure is preserved. Further data assessment by Rietveld refinement allows detection of a slight increase of the c lattice parameter and volume related to incorporation of the doping elements. XPS confirms the coexistence of both elemental and oxide carbon forms, which are predominantly located on the TiO2 particle surface. According to XPS analysis sulphur occupies titanium sites and the element is present in S6+ sulfate environment. Analysis based on cyclic voltammetry and galvanostatic intermittent titration (GITT) suggests an accelerated Li+ transport in the doped TiO2 structure. The synthesized S and C co-doped anatase has an excellent electrochemical performance in terms of capacity and very fast lithiation kinetics, superior to the non-doped TiO2. The material displays 83% capacity retention for 500 galvanostatic cycles and nearly 100% current efficiency.

  15. The incorporation of radiolabelled sulphur from captan into protein and its impact on a DNA binding study.

    Science.gov (United States)

    Provan, W M; Eyton-Jones, H; Lappin, G; Pritchard, D; Moore, R B; Green, T

    1995-05-19

    Repeated administration of high doses of captan is known to produce tumours specifically in the duodenum of mice. Captan is not carcinogenic in the rat. In this study, DNA purified from the liver, stomach, duodenum and jejenum of mice dosed with 35S radiolabelled captan was found to contain radioactivity equivalent to Covalent Binding Indices in the range 38-91; that from the bone marrow had a CBI of 2.8. The distribution of radioactivity between the various tissues did not reflect the target organ specificity of captan. Attempts to further purify the DNA samples using caesium chloride gradients resulted in partial separation of the radioactivity from the DNA suggesting that covalent binding to the DNA may not have occurred. A study of the chemical breakdown of captan showed that captan is unstable, producing a variety of potentially reactive species containing sulphur. Evidence was further obtained to show that the sulphur of captan is incorporated into endogenous amino acids and protein. Hepatic DNA from mice dosed with 35S radiolabelled N-acetylcysteine, and two thiazolidine derivatives which are analogous to known metabolites of captan, was radiolabelled to a similar extent to that from captan treated mice. Furthermore, the DNA from each of these treatments had similar properties on caesium chloride gradients. It was concluded that the radioactivity associated with DNA in the captan DNA binding study was present in the low levels of protein which are always associated with purified DNA samples.

  16. High pressure treatments accelerate changes in volatile composition of sulphur dioxide-free wine during bottle storage.

    Science.gov (United States)

    Santos, Mickael C; Nunes, Cláudia; Rocha, M Angélica M; Rodrigues, Ana; Rocha, Sílvia M; Saraiva, Jorge A; Coimbra, Manuel A

    2015-12-01

    The impact of high hydrostatic pressure (HHP) treatments on volatile composition of sulphur dioxide-free wines during bottle storage was studied. For this purpose, white and red wines were produced without sulphur dioxide (SO2) and, at the end of the alcoholic fermentation, the wines were pressurised at 500 MPa and 425 MPa for 5 min. Wine with 40 ppm of SO2 and a wine without a preservation treatment were used as controls. More than 160 volatile compounds, distributed over 12 chemical groups, were identified in the wines by an advanced gas chromatography technique. The pressurised wines contained a higher content of furans, aldehydes, ketones, and acetals, compared with unpressurised wines after 9 months of storage. The changes in the volatile composition indicate that HHP treatments accelerated the Maillard reaction, and alcohol and fatty acid oxidation, leading to wines with a volatile composition similar to those of faster aged and/or thermally treated wines. Copyright © 2015 Elsevier Ltd. All rights reserved.

  17. Past and future trends in concentrations of sulphur and nitrogen compounds in the Arctic

    DEFF Research Database (Denmark)

    Hole, Lars R.; Christensen, Jesper H.; Ruoho-Airola, Tuija

    2009-01-01

    Recent trends in nitrogen and sulphur compounds in air and precipitation from a range of Arctic monitoring stations are presented, with seasonal data from the late 70s to 2004 or 2005. Earlier findings of declining sulphur concentrations are confirmed for most stations, while the pattern is less......-2000 is reasonably well reproduced at most stations using an Eulerian, hemispherical model. Results for nitrogen compounds are weaker. Scenario studies show that even if large sulphur emission reductions take place in important source regions in South-East Asia in the coming decades, only small changes in Arctic...

  18. Effects of sulphur dioxide on southern bean mosaic and maize dwarf mosaic

    Energy Technology Data Exchange (ETDEWEB)

    Laurence, J.A.; Aluisio, A.L.; Weinstein, L.H.; McCune, D.C.

    1981-01-01

    Sub-acute doses of sulphur dioxide (SO/sub 2/) (either 262 or 524 ..mu..g m/sup -3/) for 5-10 days caused small but consistent increases in the titre of southern bean mosaic virus (SBMV) in Bountiful bean and maize dwarf mosaic virus (MDMV) in maize. Exposure to SO/sub 2/ also increased infection and intensified symptoms caused by MDMV. Sulphur uptake by the host plant was not affected by either virus; however, pre- and post-inoculation exposures of bean plants to SO/sub 2/ resulted in greater than additive effects on sulphur uptake.

  19. Preparation of high-purity bismuth by sulphur deleadization in vacuum distillation

    Institute of Scientific and Technical Information of China (English)

    熊利芝; 何则强; 刘文萍; 麻成金; 戴永年

    2004-01-01

    The feasibility of separation of impurities in refined bismuth and sulphur deleadization with vacuum distillation was studied theoretically. Experimental studies on sulphur deleadization were carried out under vacuum.The influences of amount of sulphur, distillation temperature, vacuum degree and distillation time on deleadization were investigated and an optimal technical condition was achieved. The content of lead in refined bismuth can be decreased from 30 μg/g to 0.21 μg/g, which has reached the level of "5N" high-purity bismuth. Other impurities in refined bismuth can be also removed effectively under certain conditions.

  20. Lipids and Composition of Fatty Acids of Saccharina latissima Cultivated Year-round in Integrated Multi-trophic Aquaculture

    DEFF Research Database (Denmark)

    Silva Marinho, Goncalo; Holdt, Susan Løvstad; Jacobsen, Charlotte

    2015-01-01

    in January was significantly different from all the other sampling months. The dissimilarities were mainly explained by changes in the relative abundance of 20:5n-3 (13.12%-33.35%), 14:0 (11.07%-29.37%) and 18:1n-9 (10.15%-16.94%). Polyunsaturated fatty acids (PUFA's) made up more than half of the fatty...... acids with a maximum in July (52.3%-54.0% fatty acid methyl esters; FAME). This including the most appreciated health beneficial PUFA's, eicosapentaenoic (EPA; 20:5n-3) and docosahexaenoic acid (DHA; 22:6n-3), but also arachidonic (ARA) and stearidonic acid (SDA), which are not found in land vegetables......This study is evaluating the seasonal lipid and fatty acid composition of the brown seaweed Saccharina latissima. Biomass was sampled throughout the year (bi-monthly) at the commercial cultivation site near a fish farm in an integrated multi-trophic aquaculture (IMTA) and at a reference site...

  1. Characterizing the interaction between uranyl ion and fulvic acid using regional integration analysis (RIA) and fluorescence quenching.

    Science.gov (United States)

    Zhu, Bingqi; Ryan, David K

    2016-03-01

    The development of chemometric methods has substantially improved the quantitative usefulness of the fluorescence excitation-emission matrix (EEM) in the analysis of dissolved organic matter (DOM). In this study, Regional Integration Analysis (RIA) was used to quantitatively interpret EEMs and assess fluorescence quenching behavior in order to study the binding between uranyl ion and fulvic acid. Three fulvic acids including soil fulvic acid (SFA), Oyster River fulvic acid (ORFA) and Suwannee River fulvic acid (SRFA) were used and investigated by the spectroscopic techniques. The EEM spectra obtained were divided into five regions according to fluorescence structural features and two distinct peaks were observed in region III and region V. Fluorescence quenching analysis was conducted for these two regions with the stability constants, ligand concentrations and residual fluorescence values calculated using the Ryan-Weber model. Results indicated a relatively strong binding ability between uranyl ion and fulvic acid samples at low pH (log K value varies from 4.11 to 4.67 at pH 3.50). Fluorophores in region III showed a higher binding ability with fewer binding sites than in region V. Stability constants followed the order, SFA > ORFA > SRFA, while ligand concentrations followed the reverse order, SRFA > ORFA > SFA. A comparison between RIA and Parallel Factor Analysis (PARAFAC) data treatment methods was also performed and good agreement between these two methods (less than 4% difference in log K values) demonstrates the reliability of the RIA method in this study.

  2. Production of D-lactic acid in a continuous membrane integrated fermentation reactor by genetically modified Saccharomyces cerevisiae: enhancement in D-lactic acid carbon yield.

    Science.gov (United States)

    Mimitsuka, Takashi; Sawai, Kenji; Kobayashi, Koji; Tsukada, Takeshi; Takeuchi, Norihiro; Yamada, Katsushige; Ogino, Hiroyasu; Yonehara, Tetsu

    2015-01-01

    Poly d-lactic acid is an important polymer because it improves the thermostability of poly l-lactic acid by stereo complex formation. To demonstrate potency of continuous fermentation using a membrane-integrated fermentation reactor (MFR) system, continuous fermentation using genetically modified Saccharomyces cerevisiae which produces d-lactic acid was performed at the low pH and microaerobic conditions. d-Lactic acid continuous fermentation using the MFR system by genetically modified yeast increased production rate by 11-fold compared with batch fermentation. In addition, the carbon yield of d-lactic acid in continuous fermentation was improved to 74.6 ± 2.3% compared to 39.0 ± 1.7% with batch fermentation. This dramatic improvement in carbon yield could not be explained by a reduction in carbon consumption to form cells compared to batch fermentation. Further detailed analysis at batch fermentation revealed that the carbon yield increased to 76.8% at late stationary phase. S. cerevisiae, which exhibits the Crabtree-positive effect, demonstrated significant changes in metabolic activities at low sugar concentrations (Rossignol et al., Yeast, 20, 1369-1385, 2003). Moreover, lactate-producing S. cerevisiae requires ATP supplied not only from the glycolytic pathway but also from the TCA cycle (van Maris et al., Appl. Environ. Microbiol., 70, 2898-2905, 2004). Our finding was revealed that continuous fermentation, which can maintain the conditions of both a low sugar concentration and air supply, results in Crabtree-positive and lactate-producing S. cerevisiae for suitable conditions of d-lactic acid production with respect to redox balance and ATP generation because of releasing the yeast from the Crabtree effect.

  3. [Integral bread development with soybean, chia, linseed, and folic acid as a functional food for women].

    Science.gov (United States)

    Justo, Mayela Bautista; Alfaro, Alejandra Denisse Castro; Aguilar, Ernesto Camarena; Wrobel, Katarzyna; Wrobel, Kazimierz; Guzmán, Guadalupe Alanís; Sierra, Zeferino Gamiño; Zanella, Victor Da Mota

    2007-03-01

    Six bread formulations were developed, using different proportions of whole-wheat flour, chia seeds and flaxseed flour. All of our formulations were added with folic acid. Sensorial and texture evaluations were performed, showing good acceptance of the products. Proximal chemical analysis was carried out; in addition, the following parameters were determined: calcium, phosphorus, total dietary fiber, folic acid, water hydration capacity, Glucose Dialysis Retardation Index (GDRI) and fatty acids. The results obtained showed higher protein levels in the developed breads (23.23-30.24 (g/100g dry matter) as compared to a control (21.00% of proteins in bread elaborated without chia or flaxseed). Furthermore, the breads contained 10.07-12.15 of lipids (g/100g dry matter) (linoleic acid: 2.43-4.05%; linolenic acid: 1.12-4.46 %; oleic acid: 2.93-6.13 %), GDRI values were between 89.1 and 98.1 % and folic acid was in the range 699.44 - 991.3 (microg/100g dry matter). The same parameters were determined in the chia seed and in the flaxseed flour. It was concluded that; due to their high levels of protein, insaturated fatty acids (omega-3 and omega-6), dietary fiber and folic acid, these breads have a high nutritional value, so they could have special benefits for woman.

  4. An integrated bioconversion process for the production of L-lactic acid from starchy feedstocks

    Energy Technology Data Exchange (ETDEWEB)

    Tsai, S.P.; Moon, S.H.

    1997-07-01

    The potential market for lactic acid as the feedstock for biodegradable polymers, oxygenated chemicals, and specialty chemicals is significant. L-lactic acid is often the desired enantiomer for such applications. However, stereospecific lactobacilli do not metabolize starch efficiently. In this work, Argonne researchers have developed a process to convert starchy feedstocks into L-lactic acid. The processing steps include starch recovery, continuous liquefaction, and simultaneous saccharification and fermentation. Over 100 g/L of lactic acid was produced in less than 48 h. The optical purity of the product was greater than 95%. This process has potential economical advantages over the conventional process.

  5. Uncertainty quantification and integration of machine learning techniques for predicting acid rock drainage chemistry: a probability bounds approach.

    Science.gov (United States)

    Betrie, Getnet D; Sadiq, Rehan; Morin, Kevin A; Tesfamariam, Solomon

    2014-08-15

    Acid rock drainage (ARD) is a major pollution problem globally that has adversely impacted the environment. Identification and quantification of uncertainties are integral parts of ARD assessment and risk mitigation, however previous studies on predicting ARD drainage chemistry have not fully addressed issues of uncertainties. In this study, artificial neural networks (ANN) and support vector machine (SVM) are used for the prediction of ARD drainage chemistry and their predictive uncertainties are quantified using probability bounds analysis. Furthermore, the predictions of ANN and SVM are integrated using four aggregation methods to improve their individual predictions. The results of this study showed that ANN performed better than SVM in enveloping the observed concentrations. In addition, integrating the prediction of ANN and SVM using the aggregation methods improved the predictions of individual techniques.

  6. Chemical characterization of sulphur-iodine thermochemical cycle flowstreams by Raman spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Liberatore, Raffaele; Falconieri, Mauro; Lanchi, Michela; Spadoni, Annarita [ENEA CR, Casaccia (Italy)

    2010-07-01

    The Sulphur-Iodine (S-I) thermochemical cycle for hydrogen production from water is one of the widest investigated cycles in the world. Considered the complexity of the S-I process scheme, the focus on chemical characterization of the flowstreams in the loop plant is crucial in order to fully understand chemical equilibriums involved at varying hydriodic acid: (HI:I{sub 2}) ratio in the mixtures and to determine HI and I{sub 2} contents as well. Raman spectroscopy has been widely used to investigate iodine solutions, however few works deals with I{sub 2} in HI aqueous mixtures. The aim of the present study is to use Raman spectroscopy for a rapid qualitative and quantitative characterization of the HI-H{sub 2}O-I{sub 2} mixtures involved in the S-I process. At this purpose, Raman spectra of solutions with known HI and I{sub 2} concentration have been recorded at varying I{sub 2} and HI compositions. It has been found that the chemistry of these solutions is highly dependant on HI:I{sub 2} molar ratio. For ratio up to 1:1, the dominant iodine compounds are I{sub 3}{sup -} and its corresponding ion pair HI{sub 3}. At higher values, close to those of the hydriodic phase HIx of the Bunsen reaction, there is experimental evidence of the formation of higher polyiodine and polyiodides compounds. (orig.)

  7. Impregnated silica nanoparticles for the reactive removal of sulphur mustard from solutions.

    Science.gov (United States)

    Singh, Beer; Saxena, Amit; Nigam, Anil Kumar; Ganesan, Kumaran; Pandey, Pratibha

    2009-01-30

    High surface area (887.3m(2)/g) silica nanoparticles were synthesized using aerogel route and thereafter, characterized by N(2)-Brunauer-Emmet-Teller (BET), SEM and TEM techniques. The data indicated the formation of nanoparticles of silica in the size range of 24-75 nm with mesoporous characteristics. Later, these were impregnated with reactive chemicals such as N-chloro compounds, oxaziridines, polyoxometalates, etc., which have already been proven to be effective against sulphur mustard (HD). Thus, developed novel mesoporous reactive sorbents were tested for their self-decontaminating feature by conducting studies on kinetics of adsorptive removal of HD from solution. Trichloroisocyanuric acid impregnated silica nanoparticles (10%, w/w)-based system was found to be the best with least half-life value (t(1/2)=2.8 min) among prepared systems to remove and detoxify HD into nontoxic degradation products. Hydrolysis, dehydrohalogenation and oxidation reactions were found to be the route of degradation of HD over prepared sorbents. The study also inferred that 10% loading of impregnants over high surface area and low density silica nanoparticles enhances the rate of reaction kinetics and seems to be useful in the field of heterogeneous reaction kinetics.

  8. [Influence of calcic and magnesic sulphurous thermal water on the metabolism of lipoproteins in the rat].

    Science.gov (United States)

    Toussaint, C; Peuchant, E; Nguyen, B C; Jensen, R; Canellas, J

    1986-06-01

    We have studied in rats fed hypercholesterolemic diet the action of calcic and magnesic sulphurous water from Capvern on the modification of the lipoproteins metabolism caused by hypercholesterolemia. The rats subjected to a hypercholesterolemic diet with thermal water of Capvern was found to have a plasma level of cholesterol significantly less increased (P less than 0.01) compared to those subjected to the same diet with ordinary drinking water (25%). We demonstrated after 105 days of experimentation on tested rats that thermal water may affect the cholesterol catabolism by increased level of cholesterol HDL (52%) and stabilizing level of cholesterol LDL comparatively to the controls. These data suggest that the thermal water from Capvern enhanced the transformation of cholesterol to biliary acids and their biliary secretion. A possible relationship between the influence of the thermal water and the metabolism of lipoproteins would be explained by a possible increase of hepatic receptors which identify apolipoproteins B (LDL) and E (HDLc) on cholesterol fed rats, suggesting a great synthesis of nascent apolipoproteins HDL which are antiatherogenic.

  9. Transformation and Deposition of Sulphur and Nitrogen Compounds in the Marine Boundary Layer

    Energy Technology Data Exchange (ETDEWEB)

    Hertel, O.

    1995-10-01

    In this thesis the author performs a model study of the transformation and deposition of sulphur and nitrogen compounds in the marine boundary layer, including source-receptor relationships. The central part of the study is the development and testing of a variable scale trajectory model for Europe, with special emphasis on modelling the concentrations of gases and aerosols in the marine atmosphere and the deposition to sea. A one-dimensional version of the model was developed to model the chemical degradation of dimethyl sulphide (DMS) in the marine boundary layer. Although the model reproduces the observed levels of DMS and methane sulphonic acid (MSA) well, the calculated DMS concentration is not always in phase with observed levels, probably because of a local coastal emission that is correlated with the shifting tide. Another version of the trajectory model, Atmospheric Chemistry and Deposition model (ACDEP), was developed to study the deposition of nitrogen compounds to the Danish sea waters. This model uses a new numerical scheme, the Eulerian Backward Iterative method. The model is able to reproduce observations of air concentrations and wet deposition fairly well; data for dry deposition were not available. The model was also used for calculation of deposition of nitrogen compounds to the Kattegat. Finally, a sensitivity study was performed on the model. 175 refs., 87 figs., 32 tabs.

  10. Integration of succinic acid and ethanol production within a corn or barley biorefinery

    Science.gov (United States)

    Production of succinic acid from glucose by Escherichia coli strain AFP184 was studied in a batch fermentor. The bases used for pH control included NaOH, KOH, NH4OH, and Na2CO3. The yield of succinic acid without and with carbon dioxide supplied by an adjacent ethanol fermentor using either corn or ...

  11. Integrated treatment of acid mine drainage using cryptocrystalline magnesite and barium chloride

    CSIR Research Space (South Africa)

    Masindi, Vhahangwele

    2017-08-01

    Full Text Available This study endeavours to report the efficiency of a hybrid approach in the treatment of acid mine drainage. Cryptocrystalline magnesite was used to pre-treat acid mine drainage and barium chloride was used to remove the residual sulphate through...

  12. Integration of chlorogenic acid recovery and bioethanol production from spent coffee grounds

    DEFF Research Database (Denmark)

    Burniol Figols, Anna; Cenian, Katarzyna; Skiadas, Ioannis V.

    2016-01-01

    Spent coffee grounds (SCG) are an abundant by-product of the coffee industry with a complex composition that makes them a promising feedstock for a biorefinery. The objective of this study was to evaluate SCG as a substrate for combined chlorogenic acid and bioethanol production after dilute acid...

  13. Sulphur functionality study of steam pyrolyzed 'Mequinenza' lignite using reductive pyrolysis technique coupled with MS and GC/MS detection systems

    Energy Technology Data Exchange (ETDEWEB)

    Marinov, S.P.; Stefanova, M.; Stamenova, V. [Institute of Organic Chemistry, Bulgarian Academy of Sciences, Sofia (Bulgaria); Carleer, R.; Yperman, J. [Laboratory of Applied Chemistry, CMK, Limburgs Universitair Centrum, B-3590 Diepenbeek (Belgium)

    2005-02-25

    Atmospheric pressure-temperature programmed reduction (AP-TPR) and its analogous in oxidative atmosphere coupled 'on-line' with a mass spectrometer (MS) were used to study the behaviour of organic sulphur forms of 'Mequinenza' lignite during their mild steam pyrolysis. The obtained data were confirmed and completed by the AP-TPR-GC/MS 'off-line' analysis. Samples under study were pyrolyzed at different processing parameters (temperature and flow gas). Some peculiarities in the distribution of non-thiophenic sulphur forms depending on experimental conditions were found. Namely, their amounts decreased with temperature increase at the steam treatment. The experiment performed at 500 {sup o}C in water vapor flow proved the C-S bond splitting in dibenzothiophene with biphenyl formation. Sulphonic acid compounds were also systematically removed. At higher temperature of the steam pyrolyzed treatment, this effect was more pronounced. At the same time, a relative increase in sulphones was found.The following organic sulphur species in demineralised lignite were detected by the 'off-line' AP-TPR-GC/MS technique: methyl- and benzenethiols; mono- and disulphides; alkylthiolanes; alkenyl thiophenes; alkylbenzo[b]thiophenes and alkyldibenzo[bd]thiophenes. Their relative intensities as a function of temperature were followed. A strong preponderance of benzo[b]thiophene and its alkylated homologues above 450 {sup o}C were observed. Thiophene presence was temperature independent.

  14. Mycolic Acid Cyclopropanation is Essential for Viability, Drug Resistance, and Cell Wall Integrity of Mycobacterium tuberculosis

    Energy Technology Data Exchange (ETDEWEB)

    Barkan, Daniel; Liu, Zhen; Sacchettini, James C.; Glickman, Michael S.; (MSKCC); (TAM)

    2009-12-01

    Mycobacterium tuberculosis infection remains a major global health problem complicated by escalating rates of antibiotic resistance. Despite the established role of mycolic acid cyclopropane modification in pathogenesis, the feasibility of targeting this enzyme family for antibiotic development is unknown. We show through genetics and chemical biology that mycolic acid methyltransferases are essential for M. tuberculosis viability, cell wall structure, and intrinsic resistance to antibiotics. The tool compound dioctylamine, which we show acts as a substrate mimic, directly inhibits the function of multiple mycolic acid methyltransferases, resulting in loss of cyclopropanation, cell death, loss of acid fastness, and synergistic killing with isoniazid and ciprofloxacin. These results demonstrate that mycolic acid methyltransferases are a promising antibiotic target and that a family of virulence factors can be chemically inhibited with effects not anticipated from studies of each individual enzyme.

  15. Semicontinuous Production of Lactic Acid From Cheese Whey Using Integrated Membrane Reactor

    Science.gov (United States)

    Li, Yebo; Shahbazi, Abolghasem; Coulibaly, Sekou; Mims, Michele M.

    Semicontinuous production of lactic acid from cheese whey using free cells of Bifidobacterium longum with and without nanofiltration was studied. For the semicontinuous fermentation without membrane separation, the lactic acid productivity of the second and third runs is much lower than the first run. The semicontinuous fermentation with nanoseparation was run semicontinuously for 72 h with lactic acid to be harvested every 24 h using a nanofiltration membrane unit. The cells and unutilized lactose were kept in the reactor and mixed with newly added cheese whey in the subsequent runs. Slight increase in the lactic acid productivity was observed in the second and third runs during the semicontinuous fermentation with nanofiltration. It can be concluded that nanoseparation could improve the lactic acid productivity of the semicontinuous fermentation process.

  16. Investigation of sulphur isotope variation due to different processes applied during uranium ore concentrate production.

    Science.gov (United States)

    Krajkó, Judit; Varga, Zsolt; Wallenius, Maria; Mayer, Klaus; Konings, Rudy

    The applicability and limitations of sulphur isotope ratio as a nuclear forensic signature have been studied. The typically applied leaching methods in uranium mining processes were simulated for five uranium ore samples and the n((34)S)/n((32)S) ratios were measured. The sulphur isotope ratio variation during uranium ore concentrate (UOC) production was also followed using two real-life sample sets obtained from industrial UOC production facilities. Once the major source of sulphur is revealed, its appropriate application for origin assessment can be established. Our results confirm the previous assumption that process reagents have a significant effect on the n((34)S)/n((32)S) ratio, thus the sulphur isotope ratio is in most cases a process-related signature.

  17. Investigation of the possibility of binding fly ash particles by elemental sulphur

    Directory of Open Access Journals (Sweden)

    Vidojković V.

    2006-01-01

    Full Text Available Thermal power plants in Serbia use lignite for electrical power production The secondary product of coal combustion is fly ash in the amount of 17%. Fly ash causes the pollution of air, water and soil, and also cause many human, especially lung diseases. Secondary sulphur is a product of crude oil refining. The aim of this study was to investigate the use of sulphur as a bonding material in ultra fine particle agglomeration (smaller than 63 μm in fly ash. The agglomeration should make the ash particles larger and heavy enough to fall without flying fractions. The experiments showed that during the homogenization of the ashes and sulphur from 150 to 170 °C in a reactor with intensive mixing, an amount of 15% sulphur was sufficient to bond particles and cause agglomeration without visible flying fractions.

  18. Low surface area graphene/cellulose composite as a host matrix for lithium sulphur batteries

    Science.gov (United States)

    Patel, Manu U. M.; Luong, Nguyen Dang; Seppälä, Jukka; Tchernychova, Elena; Dominko, Robert

    2014-05-01

    Graphene/cellulose composites were prepared and studied as potential host matrixes for sulphur impregnation and use in Li-S batteries. We demonstrate that with the proper design of a relatively low surface area graphene/cellulose composite, a high electrochemical performance along with good cyclability can be achieved. Graphene cellulose composites are built from two constituents: a two-dimensional electronic conductive graphene and cellulose fibres as a structural frame; together they form a laminar type of pore. The graphene sheets that uniformly anchor sulphur molecules provide confinement ability for polysulphides, sufficient space to accommodate sulphur volumetric expansion, a large contact area with the sulphur and a short transport pathway for both electrons and lithium ions. Nano-cellulose prevents the opening of graphene sheets due to the volume expansion caused by dissolved polysulphides during battery operation. This, in turn, prevents the diffusion of lithium polysulphides into the electrolyte, enabling a long cycle life.

  19. Isoprene, sulphoxy radical-anions and acidity

    Science.gov (United States)

    Rudziński, K. J.; Gmachowski, L.; Kuznietsova, I.

    2008-12-01

    Transformation of isoprene coupled with autoxidation of SIV in aqueous solutions was studied experimentally and by chemical-kinetic modelling over broad range of solution acidities (pH=3-9) to complement the research on aqueous-phase and heterogeneous transformation of isoprene reported recently by many laboratories. Isoprene significantly slowed down the autoxidation in acidic and basic solutions, and accelerated it slightly in neutral solutions. Simultaneously, production of sulphate ions and formation of solution acidity were significantly reduced. Formation of sulphite and sulphate derivatives of isoprene - sulphurous acid mono-(2-methyl-4-oxo-but-2-enyl) ester (m/z=162.9), sulphurous acid mono-(4-hydroxy-2-methyl-but-2-enyl) ester (m/z=164.9), sulphuric acid mono-(2-methyl-4-oxo-but-2-enyl) ester (m/z=178.9), sulphuric acid mono-(4-hydroxy-2-methyl-but-2-enyl) ester (m/z=180.9) - was indicated by mass spectroscopic analysis of post-reaction mixtures. The results of experiments were explained by changes in a subtle quantitative balance of three superimposed processes whose rates depended in different manner on the acidity of reacting solutions - the scavenging of sulphoxy radicals by isoprene, the formation of sulphoxy radicals during further reactions of isoprene radicals, and the autoxidation of SIV itself. A chemical mechanism based on this idea was explored numerically to show good agreement with experimental data. Interaction of isoprene with sulphur(IV) species and oxygen can possibly result in formation of new organosulphate components of atmospheric aerosols and waters, and influence distribution of reactive sulphur and oxygen species in isoprene-emitting organisms exposed to SIV pollutants.

  20. Isoprene, sulphoxy radical-anions and acidity

    Directory of Open Access Journals (Sweden)

    K. J. Rudziński

    2008-12-01

    Full Text Available Transformation of isoprene coupled with autoxidation of SIV in aqueous solutions was studied experimentally and by chemical-kinetic modelling over broad range of solution acidities (pH=3–9 to complement the research on aqueous-phase and heterogeneous transformation of isoprene reported recently by many laboratories. Isoprene significantly slowed down the autoxidation in acidic and basic solutions, and accelerated it slightly in neutral solutions. Simultaneously, production of sulphate ions and formation of solution acidity were significantly reduced. Formation of sulphite and sulphate derivatives of isoprene – sulphurous acid mono-(2-methyl-4-oxo-but-2-enyl ester (m/z=162.9, sulphurous acid mono-(4-hydroxy-2-methyl-but-2-enyl ester (m/z=164.9, sulphuric acid mono-(2-methyl-4-oxo-but-2-enyl ester (m/z=178.9, sulphuric acid mono-(4-hydroxy-2-methyl-but-2-enyl ester (m/z=180.9 – was indicated by mass spectroscopic analysis of post-reaction mixtures. The results of experiments were explained by changes in a subtle quantitative balance of three superimposed processes whose rates depended in different manner on the acidity of reacting solutions – the scavenging of sulphoxy radicals by isoprene, the formation of sulphoxy radicals during further reactions of isoprene radicals, and the autoxidation of SIV itself. A chemical mechanism based on this idea was explored numerically to show good agreement with experimental data. Interaction of isoprene with sulphur(IV species and oxygen can possibly result in formation of new organosulphate components of atmospheric aerosols and waters, and influence distribution of reactive sulphur and oxygen species in isoprene-emitting organisms exposed to SIV pollutants.

  1. Study on Friction and Wear Characteristics and Structure of Compound Layer from Combined Treatment of Ion Nitrocarburizing-Ion Sulphurizing of CrMoCu Alloy Cast Iron

    Institute of Scientific and Technical Information of China (English)

    MAShi-ning; HUChun-hua; LIXin; QIUJi

    2004-01-01

    The technics of combined treatment of ion nitrocarburizing-ion sulpburizing of CrMoCu alloy cast iron has been investigated and the compound layer with nitrocabonide and sulphide has been made on the surface of CrMoCu alloy cast iron. The compound layer is composed of sulfide surface layer and the nitrocarbonide hypo-surface layer and its diffusing laye. The size of sulfide globular grains distributing equably on the surface is in nano-micmn-scale, and the phase structure of the compound layer is composed of FeS, FeS2, Fe2C and FerN. Under dry sliding condition, the friction-reducing of sulphurized surface is good, but its function time can't last vet3. long, The nitrocarbonided+sulphurized surface can gready improve the wear-resistance and the friction-reducing of CrMoCu alloy cast iron, and its integrated friction and wear properties are better than plain and sulphurized surfaces.

  2. Effects of humic acids from landfill leachate on plants: An integrated approach using chemical, biochemical and cytogenetic analysis.

    Science.gov (United States)

    Morozesk, Mariana; Bonomo, Marina Marques; Souza, Iara da Costa; Rocha, Lívia Dorsch; Duarte, Ian Drumond; Martins, Ian Oliveira; Dobbss, Leonardo Barros; Carneiro, Maria Tereza Weitzel Dias; Fernandes, Marisa Narciso; Matsumoto, Silvia Tamie

    2017-10-01

    Biological process treatment of landfill leachate produces a significant amount of sludge, characterized by high levels of organic matter from which humic acids are known to activate several enzymes of energy metabolism, stimulating plant growth. This study aimed to characterize humic acids extracted from landfill sludge and assess the effects on plants exposed to different concentrations (0.5, 1, 2 and 4 mM C L(-1)) by chemical and biological analysis, to elucidate the influence of such organic material and minimize potential risks of using sludge in natura. Landfill humic acids showed high carbon and nitrogen levels, which may represent an important source of nutrients for plants. Biochemical analysis demonstrated an increase of enzyme activity, especially H(+)-ATPase in 2 mM C L(-1) landfill humic acid. Additionally, cytogenetic alterations were observed in meristematic and F1 cells, through nuclear abnormalities and micronuclei. Multivariate statistical analysis provided integration of physical, chemical and biological data. Despite all the nutritional benefits of humic acids and their activation of plant antioxidant systems, the observed biological effects showed concerning levels of mutagenicity. Copyright © 2017 Elsevier Ltd. All rights reserved.

  3. Tobacco LSU-like protein couples sulphur-deficiency response with ethylene signalling pathway

    OpenAIRE

    Moniuszko, Grzegorz; Skoneczny, Marek; Zientara-Rytter, Katarzyna; Wawrzyńska, Anna; Głów, Dawid; Cristescu, Simona M; Harren, Frans J. M.; Sirko, Agnieszka

    2013-01-01

    Most genes from the plant-specific family encoding Response to Low Sulphur (LSU)-like proteins are strongly induced in sulphur (S)-deficient conditions. The exact role of these proteins remains unclear; however, some data suggest their importance for plants’ adjustment to nutrient deficiency and other environmental stresses. This work established that the regulation of ethylene signalling is a part of plants’ response to S deficiency and showed the interaction between UP9C, a tobacco LSU fami...

  4. Evolution of the Total Sulphur Content in Full-Scale Wastewater Sludge Treatment

    OpenAIRE

    Dewil, Raf; Baeyens, Jan; Roels, Joris; Van De Steene, Boudewijn

    2009-01-01

    The present research studies the evolution of sulphur concentrations during wastewater treatment for various full-scale treatment plants and reveals that a significant amount of S is released as highly soluble sulphates with the sludge water during sludge thickening when sludge is still in aerobic conditions. During digestion, sulphur concentrations in the sludge (expressed as mg S/kg of dry solids) generally increased due to destruction of organic material, and relatively low release of H2S....

  5. Investigation of pitch-sulphur mixtures used as binder in the preparation of black ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Clausse, V.; Bastien, T.; Hoppe, S.; Mareche, J.F.; Fierro, V.; Celzard, A. [Nancy University, Nancy (France)

    2009-08-15

    Since tens of years, sulphur is a very classical additive in the composition of black ceramics because, if added in small amounts (i.e., less than 10 wt.% of the binder), it improves their mechanical properties without strongly degrading their graphitability and their conductivity. Macroscopic properties of black ceramics strongly depend on the quality of the interfaces between grains of solid filler (graphite, carbon black) and coke originating from the pyrolysis of the binder; thus, the binder should correctly wet the filler prior to the carbonisation process. Coal-tar pitch usually exhibits a high affinity for carbon grains. In the effect of the amount of sulphur on the viscosity of the molten binder and on the way the present work, it wets the solid filler was investigated. For that purpose, the penetration of mixtures of coal-tar pitch and sulphur inside a bed of carbon particles was studied as a function of temperature. The influence of the sulphur content on composition, optical texture, and transport properties of the derived black ceramics, as well as the way it was mixed with the other constituents, were also examined. It was found that the preparation of black ceramics may be achieved easily and in safe conditions, without evolution of H{sub 2}S, using pitch-sulphur mixtures first molten in a bladed mixer, and having sulphur contents within the range 10-20 wt.%. The presence of sulphur increases the coke yield but lowers the ability to graphitise, thus limiting the transport properties of the resultant black ceramic. The optimal concentration of sulphur should thus be a compromise between mechanical strength and other physical properties.

  6. Formation and colloidal behaviour of elemental sulphur produced from the biological oxidation of hydrogensulphide.

    OpenAIRE

    Janssen, A.J.H.

    1996-01-01

    The formation and aggregation of elemental sulphur from the microbiological oxidation of hydrogensulphide (H 2 S) by a mixed population of aerobic Thiobacillus -like bacteria has been investigated. Sulphide is formed during the anaerobic treatment of wastewaters which contain oxidized sulphur compounds such as thiosulphate, sulphite and sulphate. This sulphide has to be removed from the effluent solution of anaerobic reactors because of its detrimental characteristics e.g. toxicity, corrosive...

  7. Hydrogen adsorption on sulphur-doped SiC nanotubes

    Science.gov (United States)

    Sevak Singh, Ram

    2016-07-01

    Hydrogen (H2) is an energy carrier and clean fuel that can be used for a broad range of applications that include fuel cell vehicles. Therefore, development of materials for hydrogen storage is demanded. Nanotubes, in this context, are appropriate materials. Recently, silicon carbide nanotube (SiCNTs) have been predicted as potential nanomaterials for hydrogen storage, and atomic doping into the nanotubes improves the H2 adsorption. Here, we report H2 adsorption properties of sulphur-doped (S-doped) SiCNTs using first-principles calculations based on density functional theory. The H2 adsorption properties are investigated by calculations of energy band structures, density of states (DOS), adsorption energy and Mulliken charge population analysis. Our findings show that, compared to the intrinsic SiCNT, S-doped SiCNT is more sensitive to H2 adsorption. H2 gas adsorption on S-doped C-sites of SiCNT brings about significant modulation of the electronic structure of the nanotube, which results in charge transfer from the nanotube to the gas, and dipole-dipole interactions cause chemisorptions of hydrogen. However, in the case of H2 gas adsorption on S-doped Si-sites of the nanotube, lesser charge transfer from the nanotube to the gas results in physisorptions of the gas. The efficient hydrogen sensing properties of S-doped SiCNTs, studied here, may have potential for its practical realization for hydrogen storage application.

  8. Integration of general amino acid control and target of rapamycin (TOR) regulatory pathways in nitrogen assimilation in yeast.

    Science.gov (United States)

    Staschke, Kirk A; Dey, Souvik; Zaborske, John M; Palam, Lakshmi Reddy; McClintick, Jeanette N; Pan, Tao; Edenberg, Howard J; Wek, Ronald C

    2010-05-28

    Two important nutrient-sensing and regulatory pathways, the general amino acid control (GAAC) and the target of rapamycin (TOR), participate in the control of yeast growth and metabolism during changes in nutrient availability. Amino acid starvation activates the GAAC through Gcn2p phosphorylation of translation factor eIF2 and preferential translation of GCN4, a transcription activator. TOR senses nitrogen availability and regulates transcription factors such as Gln3p. We used microarray analyses to address the integration of the GAAC and TOR pathways in directing the yeast transcriptome during amino acid starvation and rapamycin treatment. We found that GAAC is a major effector of the TOR pathway, with Gcn4p and Gln3p each inducing a similar number of genes during rapamycin treatment. Although Gcn4p activates a common core of 57 genes, the GAAC directs significant variations in the transcriptome during different stresses. In addition to inducing amino acid biosynthetic genes, Gcn4p in conjunction with Gln3p activates genes required for the assimilation of secondary nitrogen sources such as gamma-aminobutyric acid (GABA). Gcn2p activation upon shifting to secondary nitrogen sources is suggested to occur by means of a dual mechanism. First, Gcn2p is induced by the release of TOR repression through a mechanism involving Sit4p protein phosphatase. Second, this eIF2 kinase is activated by select uncharged tRNAs, which were shown to accumulate during the shift to the GABA medium. This study highlights the mechanisms by which the GAAC and TOR pathways are integrated to recognize changing nitrogen availability and direct the transcriptome for optimal growth adaptation.

  9. Polioencephalomalacia in ruminants caused by excessive amount of sulphur - a review

    Directory of Open Access Journals (Sweden)

    Lutnicki Krzysztof

    2014-06-01

    Full Text Available Polioencephalomalacia as a result of sulphur excess is a growing problem in cattle and sheep, mainly in young, growing animals. It is common in different regions of the world. The disease develops favoured by certain conditions such as sustained provision of feed and water with high sulphur content, use of dietary supplements containing sulphur, and a habitat with high hydrogen sulphide concentration. Pathogenesis of the disease is complex, but very important are oxidative-antioxidative imbalance, dysfunction of vessels, and secondary cerebral cortex ischaemia as a result of direct and/or indirect action of sulphur metabolites, namely hydrogen sulphide, sulphides, and sulphites. Clinical signs and changes in the cerebral cortex in the form of degenerative necrotic lesions are similar to those observed in polioencephalomalacia caused by vitamin B1 deficiency, and lead and salt intoxication. Highly increased sulphur content (more than 0.3-0.4 of dry matter in the diet is the basis for differential diagnosis, as well the high concentration of hydrogen sulphide in gas and sulphides in rumen fluid. In prophylaxis and treatment the most important measure is to limit sulphur intake and in acute cases to neutralise low pH in rumen and administer vitamin B1 injections.

  10. Continuous esterification of free fatty acids in crude biodiesel by an integrated process of supercritical methanol and sodium methoxide catalyst.

    Science.gov (United States)

    Zeng, Dan; Li, Ruosong; Feng, Mingjun; Fang, Tao

    2014-10-01

    An integrated process of supercritical methanol (SCM) and sodium methoxide catalyst was developed to produce fatty acid methyl esters (FAMEs) via continuous esterification from crude biodiesel. The crude biodiesel with high free fatty acid (FFA) content must be refined to reduce the acid value (AV) for meeting the quality standards. The process parameters were studied by Box-Behnken design (BBD) of response surface methodology (RSM). The experimental results revealed that the AV of crude biodiesel decreased from 18.66 to 0.55 mg KOH g(-1) at the reaction conditions of 350 °C, 0.5 % amount of sodium methoxide catalyst, and 10 MPa. Temperature shows the most significant effect on the esterification, followed by pressure and amount of sodium methoxide catalyst. This integrated process proved to be a potential route to refine the crude biodiesel because of its continuity, high efficiency, and less energy consumption with relatively moderate reaction conditions compared with conventional methods.

  11. Distribution and integrated assessment of lead in an abandoned lead-acid battery site in Southwest China before redevelopment.

    Science.gov (United States)

    Wang, Mei; Zhang, Chao; Zhang, Zhuo; Li, Fasheng; Guo, Guanlin

    2016-06-01

    Lead-acid battery sites have contributed enormous amounts of lead to the environment, significantly affecting its global biogeochemical cycle and leaving the potential risks to human health. An abandoned lead-acid battery site prepared for redevelopment was selected in order to study the distribution of lead in soils, plants, rhizosphere soils and soil solutions. In total, 197 samples from 77 boreholes were collected and analyzed. Single extractions by acetic acid (HOAc) were conducted to assess the bioavailability and speciation of lead in soils for comparison with the parts of the plants that are aboveground. Health risks for future residential development were evaluated by the integrated exposure uptake biokinetic (IEUBK) model. The results indicated that lead concentrations in 83% of the soil samples exceeded the Chinese Environmental Quality Standard for soil (350 mg/kg for Pb) and mainly occurred at depths between 0 and 1.5 m while accumulating at the surface of demolished construction waste and miscellaneous fill. Lead concentrations in soil solutions and HOAc extraction leachates were linked closely to the contents of aboveground Broussonetia papyrifera and Artemisia annua, two main types of local plants that were found at the site. The probability density of lead in blood (PbB) in excess of 10 µg/dL could overtake the 99% mark in the residential scenario. The findings provided a relatively integrated method to illustrate the onsite investigations and assessment for similar sites before remediation and future development from more comprehensive aspects.

  12. Managing Consistency Anomalies in Distributed Integrated Databases with Relaxed ACID Properties

    DEFF Research Database (Denmark)

    Frank, Lars; Ulslev Pedersen, Rasmus

    2014-01-01

    In central databases the consistency of data is normally implemented by using the ACID (Atomicity, Consistency, Isolation and Durability) properties of a DBMS (Data Base Management System). This is not possible if distributed and/or mobile databases are involved and the availability of data also...... has to be optimized. Therefore, we will in this paper use so called relaxed ACID properties across different locations. The objective of designing relaxed ACID properties across different database locations is that the users can trust the data they use even if the distributed database temporarily...... been committed and completed, the execution has the consistency property. The above definition of the consistency property is not useful in distributed databases with relaxed ACID properties because such a database is almost always inconsistent. In the following, we will use the concept Consistency...

  13. Integrated evaluation of malonyl ginsenosides, amino acids and polysaccharides in fresh and processed ginseng.

    Science.gov (United States)

    Wan, Jin-Yi; Fan, Yong; Yu, Qing-Tao; Ge, Ya-Zhong; Yan, Chen-Pu; Alolga, Raphael N; Li, Ping; Ma, Zhong-Hua; Qi, Lian-Wen

    2015-03-25

    Many analytical methods have been developed to characterize ginsenosides in ginseng. Relatively less attention has been paid to the malonyl ginsenosides, amino acids and polysaccharides in various processing ginsengs. In this study, malonyl ginsenosides were characterized by LC-Q-TOF/MS. In positive mode, the most abundant ions at m/z 425.38 were observed corresponding to the protopanoxadiol-type ginsenosides. A rich diagnostic ion at 835.48 was shown representing the malonyl ginsenosides with at least two glucosides. Twelve malonyl ginsenosides were rapidly screened using 835.48-835.49 to restructure ion chromatograms. In negative mode, besides the high deprotonated ion, a neutral loss of 44 Da (CO2) was found. High-energy collision-induced dissociation at 50 V produced the most abundant product ion [M-H-malonyl](-) by a neutral loss of 86 Da. Determination of 17 common amino acids was performed on an automatic amino acid analyzer. Arginine, glutamic acid, and aspartic acid were abundant. The contents of amino acids were 9.1% in fresh ginseng and 3.1% in black ginseng. Phenol-sulfuric acid method was applied to analysis of polysaccharides. The contents of polysaccharides were 29.1% in fresh ginseng and 11.1% in black ginseng. The optimal growth age for the accumulation of constituents was supposed to be 5-6 years. In conclusion, the contents of malonyl ginsenosides, amino acids, and polysaccharides, based on decreasing order, ranked as follows: fresh ginseng>frozen ginseng>white ginseng>stoved ginseng>red ginseng>black ginseng. Processing should be paid more attention for the quality control of ginseng products. Copyright © 2014 Elsevier B.V. All rights reserved.

  14. Biogenic sulphur emissions and inferred non-sea-salt-sulphate cloud condensation nuclei in and around Antarctica

    Science.gov (United States)

    O'Dowd, Colin D.; Lowe, Jason A.; Smith, Michael H.; Davison, Brian; Hewitt, C. Nicholas; Harrison, Roy M.

    1997-06-01

    Accumulation mode aerosol properties and biogenic sulphur emissions over the South Atlantic and Antarctic Oceans are examined. Two contrasting air masses, polar and maritime, each possessing distinct aerosol properties, were encountered during the summer months. By examining aerosol volatile properties, polar air masses arriving from the Antarctic continent were shown to consist primarily Of H2SO4 in the accumulation mode size range, with inferred NH+4 to SO=4 molar ratios close to zero. By comparison, air masses of temperate maritime origin were significantly neutralized with molar ratios of ≈1. These results suggest a deficit of ammonia in polar air masses compared with that in maritime air masses. Dimethyl sulphide (DMS) exhibited no correlation with its putative aerosol oxidation products, although spatial coherence in atmospheric concentrations of DMS, methane sulphonic acid (MSA), and non-sea-salt (nss)-sulphate mass was observed. Volatility analysis, used to infer nss-sulphate cloud condensation nuclei (nss-sCCN) active at a supersaturation of ≈0.2%, indicates that nss-sCCN mass and number concentration were best correlated with MSA mass (r≈0.63). Aerosol volatility identified the presence of MSA in submicron non-sea-salt aerosol; however, its contribution to the aerosol mass was small relative to the contribution of sulphuric acid and ammonium bisulphate/sulphate aerosol. The marine sulphur cycle appears strongly coupled to the sea-salt cycle with, typically, 80-90% of nss-sulphate thought to be internally mixed with sea-salt aerosol. During the austral Summer of 1992/1993, a period of strong biological productivity in the Weddell Sea and sub-Antarctic Ocean, particularly during ice-melt, the cruise-average DMS flux of 61 μg m-2 d-1 corresponded to a very modest average nss-sCCN concentration of 21 cm-3. Observed peak values of DMS flux and inferred nss-CCN concentrations during the cruise were 477 μg m-2 d-1 and 64 cm-3, respectively. Events of new

  15. Integrating microbial decontamination with organic acids in HACCP programmes for muscle foods: prospects and controversies.

    Science.gov (United States)

    Smulders, F J; Greer, G G

    1998-11-10

    A considerable literature reports the antibacterial efficacy of dilute solutions of organic acids (lactic, acetic). With carcasses an overall reduction in surface contaminants of 1.5 log cycles can be expected. Carcass decontamination may not improve the safety of the resultant meat, but laboratory trials confirm that acid decontamination of subprimal and retail cuts is more efficacious. An advantage over many other intervention strategies is that residual antimicrobial activity is demonstrable over extended periods of storage. These studies have also shown that some meatborne pathogens are particularly sensitive to organic acids (i.e., Yersinia enterocolitica) while others are resistant (i.e., E. coli O157:H7). Dilute solutions of organic acids (1 to 3%) are generally without effect on the desirable sensory properties of meat when used as a carcass decontaminant. However, dependent on treatment conditions, lactic and acetic acid can produce adverse sensory changes when applied directly to meat cuts, with irreversible changes in appearance being a frequent occurrence. It is speculated that organic acid decontamination will be implemented in American abattoirs in an effort to meet specified performance standards for pathogen reduction as part of an overall HACCP program. In contrast, the EU advocates that strictly controlled processing hygiene is sufficient to ensure the safety of the product. Additional research is necessary to establish a set of treatment conditions that may permit a practicable reduction in bacterial contamination throughout the processing chain with a measurable effect on safety and storage life, without imposing any change in sensory properties. It will also be necessary to develop standard, objective measures to assess HACCP and the efficacy of decontamination procedures. Without such commercial studies controversy on the practicality of acid decontamination will persist.

  16. Automatic bionalyzer using an integrated amperometric biosensor for the determination of L-malic acid in wines.

    Science.gov (United States)

    Vargas, E; Ruiz, M A; Ferrero, F J; Campuzano, S; Ruiz-Valdepeñas Montiel, V; Reviejo, A J; Pingarrón, J M

    2016-09-01

    A new automatic bioanalyzer for L-malic acid using an integrated amperometric biosensor as detector is reported for the first time in this work. The biosensor is constructed by gold film sputtering deposition on a stainless steel disk electrode and co-immobilization of the enzymes malate dehydrogenase (MDH) and diaphorase (DP) together with the redox mediator tetrathiafulvalene (TTF) by means of dialysis membrane. The analytical performance of the biosensor was evaluated when it was used as amperometric detector in three different analytical methodologies: stirred solutions, semiautomatic FIA system and automatic bioanalyzer. The bienzyme biosensor exhibited great analytical performance in terms of sensitivity, selectivity and reproducibility of the measurements and its usefulness was demonstrated by analyzing wine reference materials with certified content of L-malic acid. The attractive analytical and operational characteristics demonstrated by the automatic bioanalyzer make it a promising simple, rapid and field-based tool for routine wine and fruit control.

  17. Origin and diagenetic transformations of C25 and C30 highly branched isoprenoid sulphur compounds : further evidence for the formation of organic sulphur compounds during early diagenesis

    NARCIS (Netherlands)

    Sinninghe Damsté, J.S.; Kohnen, M.E.L.; Rullkotter, J.; Haven, H.L. ten

    1990-01-01

    A number of C₂₅ and C₃₀ highly branched isoprenoid (HBI) sulphur compounds (e. g. , thiolanes, l-oxo-thiolanes, thiophenes, and benzo[b]thiophenes) with 2, 6, 10, 14-tetramethyl-7-(3-methylpentyl) pentadecane and 2, 6, 10, 14, 18-pentamethyl-7-(3-methylpentyl)nonadecane carbon skeletons were identif

  18. Sulphur-bound steroid and phytane carbon skeletons in geomacromolecules: Implications for the mechanism of incorporation of sulphur into organic matter

    NARCIS (Netherlands)

    Sinninghe Damsté, J.S.; Kohnen, M.E.L.; Baas, M.; Kock-van Dalen, A.C.

    1993-01-01

    Sulphur-bound steroid and phytane moieties in macromolecules present in the polar fractions of six immature samples (both crude oils and sediment extracts) have been analyzed using S-selective chemolysis methods and analytical pyrolysis. The identifications of the methylthioethers released from the

  19. Tailoring folic acid and methotrexate-attributed quantum dots for integrated cancer cell imaging and therapy

    Science.gov (United States)

    Fahmi, Mochamad Zakki; Chang, Jia-Yaw

    2016-03-01

    Potential application of folic acid and methotrexate-attributed AgInS2-ZnS quantum dots on both detection and therapeutic of cancer cell were intensively investigated on this study. In the initial step, the bright luminescent of QDs, with % QY up to 55.3, were synthesized with one-pot two-step process resulting narrow particle distribution and successfully transferred to water phase without significant effect on optical properties. The water-soluble AgInS2-ZnS quantum dots (QDs) encapsulated with oleylamine have been successfully prepared by ultrasonication assisting. Several aspect including QDs characterization, pH stability, ionic strength, and bonding properties were investigated to reach desired condition of water-soluble AgInS2-ZnS QDs. Folic acid was further conjugated to QDs for HeLa and MCF7 cancer cell imaging to performs the targeting capability. Moreover, folic acid is efficiently internalized into cell through the receptor-mediated endocytosis even when conjugated with a wide variety of molecules. Confocal imaging characterization further informs folic acid-conjugated AgInS2-ZnS QDs could most specific targeted to the human cervical (HeLa) cells. The therapeutic feature of QDs on HeLa cancer cell was conjugated by attributing methotrexate on the QDs, instead of folic acid, and the design could improve on inhibiting the cancer cell viability as well as its fluorescent intensity.

  20. Peracetic acid is a suitable disinfectant for recirculating fish-microalgae integrated multi-trophic aquaculture systems

    DEFF Research Database (Denmark)

    Liu, Dibo; Behrens, Sascha; Pedersen, Lars-Flemming

    2016-01-01

    tIntegrated multi-trophic aquaculture (IMTA) is a promising direction for the sustainable developmentof aquaculture. Microalgae have good potential to be integrated with recirculating aquaculture sys-tems because they can use the nitrogen excreted from fish and share the same optimal pH value asin...... aquaculture. As a byproduct, the microalgae biomass can be used for fish feed or biofuel. How-ever, the recirculating fish-microalgae IMTA system is under constant threat from fish pathogens andphytoplankton-lytic bacteria. Therefore, it is necessary to apply proper disinfectants as prophylaxis ortreatment...... which are effective against these threats, but safe to fish and microalgae. For this purpose,peracetic acid (PAA) is a valid option because it is highly effective against fish pathogens and bacteria atlow concentrations and degrades spontaneously to harmless residues. In the present study, we exposedthe...

  1. Car-Parrinello and path integral molecular dynamics study of the hydrogen bond in the chloroacetic acid dimer system.

    Science.gov (United States)

    Durlak, Piotr; Morrison, Carole A; Middlemiss, Derek S; Latajka, Zdzislaw

    2007-08-14

    We have studied the double proton transfer (DPT) reaction in the cyclic dimer of chloroacetic acid using both classical and path integral Car-Parrinello molecular dynamics. We also attempt to quantify the errors in the potential energy surface that arise from the use of a pure density functional. In the classical dynamics a clear reaction mechanism can be identified, where asynchronized DPT arises due to coupling between the O-H stretching oscillator and several low energy intermolecular vibrational modes. This mechanism is considerably altered when quantum tunneling is permitted in the simulation. The introduction of path integrals leads to considerable changes in the thermally averaged molecular geometry, leading to shorter and more centered hydrogen bond linkages.

  2. Car-Parrinello and path integral molecular dynamics study of the hydrogen bond in the chloroacetic acid dimer system

    Science.gov (United States)

    Durlak, Piotr; Morrison, Carole A.; Middlemiss, Derek S.; Latajka, Zdzislaw

    2007-08-01

    We have studied the double proton transfer (DPT) reaction in the cyclic dimer of chloroacetic acid using both classical and path integral Car-Parrinello molecular dynamics. We also attempt to quantify the errors in the potential energy surface that arise from the use of a pure density functional. In the classical dynamics a clear reaction mechanism can be identified, where asynchronized DPT arises due to coupling between the O-H stretching oscillator and several low energy intermolecular vibrational modes. This mechanism is considerably altered when quantum tunneling is permitted in the simulation. The introduction of path integrals leads to considerable changes in the thermally averaged molecular geometry, leading to shorter and more centered hydrogen bond linkages.

  3. Peracetic acid is a suitable disinfectant for recirculating fish-microalgae integrated multi-trophic aquaculture systems

    DEFF Research Database (Denmark)

    Liu, Dibo; Behrens, Sascha; Pedersen, Lars-Flemming

    2016-01-01

    tIntegrated multi-trophic aquaculture (IMTA) is a promising direction for the sustainable developmentof aquaculture. Microalgae have good potential to be integrated with recirculating aquaculture sys-tems because they can use the nitrogen excreted from fish and share the same optimal pH value asin...... aquaculture. As a byproduct, the microalgae biomass can be used for fish feed or biofuel. How-ever, the recirculating fish-microalgae IMTA system is under constant threat from fish pathogens andphytoplankton-lytic bacteria. Therefore, it is necessary to apply proper disinfectants as prophylaxis ortreatment...... which are effective against these threats, but safe to fish and microalgae. For this purpose,peracetic acid (PAA) is a valid option because it is highly effective against fish pathogens and bacteria atlow concentrations and degrades spontaneously to harmless residues. In the present study, we exposedthe...

  4. Sulphur dioxide from Nyiragongo volcano measured from UV camera

    Science.gov (United States)

    Brenot, Hugues; Theys, Nicolas; Minani, Abel; d'Oreye, Nicolas; Yalire Mapendano, Mathieu; Syauswa, Muhindo; Celli, Gilles; Kervyn, François; Van Roozendael, Michel

    2017-04-01

    Nyiragongo and Nyamuragira, DR Congo, are the most active African volcanoes, and pose a direct threat to local populations. The Remote Sensing and In Situ Detection and Tracking of Geohazards project (RESIST; http://resist.africamuseum.be) aims at a more in-depth understanding of the source mechanisms driving volcanic eruptions and landslides in the Kivu region. A key objective of RESIST is to combine complementary data sets from ground-based instrument networks (seismic, infrasound, GNSS), field surveys and Earth Observation techniques (SAR, DOAS, TRMM) to obtain added value information. This study focuses on retrieving the emission of sulphur dioxide from Nyiragongo, using a ground-based fast sampling UV camera (Envicam3) providing insight on emissions changes, at different temporal scales. This camera has been installed in December 2015 at Rusayo site, located 8 km on the south-east side of Nyiragongo volcano. The view of the camera is generally perpendicular to the mean direction of the wind in this area (NW-SE) giving an opportunity for estimating the SO2 flux emitted from this volcano. However the Kivu region is a tricky area for operating such an instrument (societal and meteorological reasons). The ideal cloud free conditions are extremely rare in this place and usually restricted to some early morning or the late afternoon time windows. The technique to retrieve SO2 emission from the UV images requires some knowledge about the background in order to apply the necessary correction. The camera is operating automatically from a fixed point. No clear sky data can be measured on a daily routine. The only way to obtain the background correction is to implement a synthetic background. An automatized strategy to obtain such background will be presented and illustrated with the analysis of one year of data.

  5. Postmagmatic sulphur loss in the Skaergaard Intrusion: Implications for the formation of the Platinova Reef

    Science.gov (United States)

    Andersen, Jens C. Ø.

    2006-11-01

    The stratabound Platinova Au-Pd Reef in the Skaergaard Intrusion is intimately linked to Cu-Fe sulphide minerals and occurs at a level that shows changes in the sulphur concentration and the Cu/S ratio. These features suggest that the reef is related to silicate-sulphide liquid immiscibility in the Skaergaard magma. However, although the evidence is strong, present day sulphur concentrations are too low to support such a model. The detailed knowledge of the shape, volume, and compositional relations of the Skaergaard lithologies allows for numerical modeling of sulphur and copper concentrations during fractionation of the magma. These data can be evaluated with the current models for sulphur saturation in iron-rich mafic magmas to assess the original sulphur concentrations, the extent of fractionation, the composition of sulphide liquids, and the extent of postmagmatic sulphur loss. Mass balance modeling yields initial copper and sulphur concentrations of 250 and 894 ppm for the parental magma to the Lower Zone a. Prior to sulphur saturation, Cu behaves as an incompatible element with a bulk partition coefficient in the cumulus material, DcumulusCu of 0.13 indicating some incorporation of Cu into mafic silicates (probably augite). Sulphur can be assumed to be perfectly incompatible in the cumulus minerals, although it will be included as a component of the interstitial liquid. These values yield sulphur saturation at around 635 ppm Cu and 2607 ppm S. Assuming the sulphur to originally be present as a mixture of monosulphide (MSS) and intermediate solid-solution sulphide (ISS), the primary sulphides in the cumulates would amount to 0.07 modal % through Lower and Middle Zones and 0.53 modal % on average through Upper Zone. The expected weight proportion of primary chalcopyrite / pyrrhotite evolves from 30 : 70 at the base of LZa through 26 : 74 at the level of the Platinova Reef to 18 : 82 at the Sandwich Horizon. The present-day bornite-magnetite mineral assemblage

  6. Binder free three-dimensional sulphur/few-layer graphene foam cathode with enhanced high-rate capability for rechargeable lithium sulphur batteries

    Science.gov (United States)

    Xi, Kai; Kidambi, Piran R.; Chen, Renjie; Gao, Chenlong; Peng, Xiaoyu; Ducati, Caterina; Hofmann, Stephan; Kumar, R. Vasant

    2014-05-01

    A novel ultra-lightweight three-dimensional (3-D) cathode system for lithium sulphur (Li-S) batteries has been synthesised by loading sulphur on to an interconnected 3-D network of few-layered graphene (FLG) via a sulphur solution infiltration method. A free-standing FLG monolithic network foam was formed as a negative of a Ni metallic foam template by CVD followed by etching away of Ni. The FLG foam offers excellent electrical conductivity, an appropriate hierarchical pore structure for containing the electro-active sulphur and facilitates rapid electron/ion transport. This cathode system does not require any additional binding agents, conductive additives or a separate metallic current collector thus decreasing the weight of the cathode by typically ~20-30 wt%. A Li-S battery with the sulphur-FLG foam cathode shows good electrochemical stability and high rate discharge capacity retention for up to 400 discharge/charge cycles at a high current density of 3200 mA g-1. Even after 400 cycles the capacity decay is only ~0.064% per cycle relative to the early (e.g. the 5th cycle) discharge capacity, while yielding an average columbic efficiency of ~96.2%. Our results indicate the potential suitability of graphene foam for efficient, ultra-light and high-performance batteries.A novel ultra-lightweight three-dimensional (3-D) cathode system for lithium sulphur (Li-S) batteries has been synthesised by loading sulphur on to an interconnected 3-D network of few-layered graphene (FLG) via a sulphur solution infiltration method. A free-standing FLG monolithic network foam was formed as a negative of a Ni metallic foam template by CVD followed by etching away of Ni. The FLG foam offers excellent electrical conductivity, an appropriate hierarchical pore structure for containing the electro-active sulphur and facilitates rapid electron/ion transport. This cathode system does not require any additional binding agents, conductive additives or a separate metallic current collector

  7. Environmental impacts of producing bioethanol and biobased lactic acid from standalone and integrated biorefineries using a consequential and an attributional life cycle assessment approach

    DEFF Research Database (Denmark)

    Parajuli, Ranjan; Knudsen, Marie Trydeman; Birkved, Morten

    2017-01-01

    : a standalone system producing bioethanol from winter wheat-straw (system A), a standalone system producing biobased lactic acid from alfalfa (system B), and an integrated biorefinery system (system C) combining the two standalone systems and producing both bioethanol and lactic acid. The synergy...

  8. Efficacy of eight commercial formulations of lime sulphur on in vitro growth inhibition of Microsporum canis.

    Science.gov (United States)

    Diesel, Alison; Verbrugge, Maria; Moriello, Karen A

    2011-04-01

    Lime sulphur is a common topical treatment for dermatophytosis in animals. Until recently, a single veterinary lime sulphur formulation was available. The purpose of this study was to compare the efficacy of eight lime sulphur products for in vitro growth inhibition of Microsporum canis using the isolated infected spore model. Infective M. canis spores were isolated from hairs collected from untreated cats. Hairs were macerated in Triton-X solution and isolated according to a previously published protocol. Equal volumes of spore suspension and lime sulphur solutions were incubated for 5 min and plated onto modified BBL™ Mycosel™ agar (Becton, Dickinson and Company; Sparks, MD, USA) plates. Five plates were inoculated for each sample solution. Distilled water and bleach were used as controls. Colony forming units were counted daily for 21 days; positive control plates contained >300 colony forming units/plate. Seven of the products were supplied as concentrates and they were tested at the manufacturer's recommended dilution, twice label concentration and half label concentration. A prediluted product SulfaDip(®) (Trask Research, Inc.; Daluca, GA, USA) was tested at the label and half label concentration. All veterinary products formed recommended treatment dilutions of 3% sulphurated lime solution except one (LymDyp(®), IVX Animal Health Inc.; St Joseph, MO, USA), which formed a 2.4% sulphurated lime solution. Results of the study showed complete growth inhibition of M. canis spores by all products at all dilutions tested. These results indicate that all tested lime sulphur-containing products were equivalent. Field studies are needed to test product equivalency in vivo.

  9. Dietary acid load, trabecular bone integrity, and mineral density in an ageing population: the Rotterdam study

    NARCIS (Netherlands)

    E.A.L. de Jonge (Ester); F. Koromani (Fjorda); A. Hofman (Albert); A.G. Uitterlinden (André); O.H. Franco (Oscar); F. Rivadeneira Ramirez (Fernando); J.C. Kiefte-de Jong (Jessica)

    2017-01-01

    textabstractSummary: We studied the relation between a diet that is high in acid-forming nutrients (e.g. proteins) and low in base-forming nutrients (e.g. potassium) and bone structure. We showed a negative relation, which was more prominent if proteins were of animal rather than of vegetable origin

  10. Integrated iron(II) oxidation and limestone neutralisation of acid mine water

    CSIR Research Space (South Africa)

    Maree, JP

    1999-01-01

    Full Text Available Volumetric iron (II) oxidation rates exceeding 100 g/(l.d) were achieved by dosing powdered limestone to a bio-reactor treating artificial acid mine water. Neutralisation and partial sulphate removal were achieved as well. The rate is highly...

  11. Acid Gas Removal by Customized Sorbents for Integrated Gasification Fuel Cell Systems

    Energy Technology Data Exchange (ETDEWEB)

    Kapfenberger, J.; Sohnemann, J.; Schleitzer, D.; Loewen, A.

    2002-09-20

    In order to reduce exergy losses, gas cleaning at high temperatures is favored in IGFC systems. As shown by thermodynamic data, separation efficiencies of common sorbents decrease with increasing temperature. Therefore, acid gas removal systems have to be developed for IGFC applications considering sorbent capacity, operation temperature, gasification feedstock composition and fuel cell threshold values.

  12. National Acid Precipitation Assessment Program Report to Congress: An Integrated Assessment

    Energy Technology Data Exchange (ETDEWEB)

    Uhart, M.; et al,

    2005-08-01

    Under Title IX of the 1990 Clean Air Act Amendments, Congress reauthorized the National Acid Precipitation Assessment Program (NAPAP) to continue coordinating acid rain research and monitoring, as it had done during the previous decade, and to provide Congress with periodic reports. In particular, Congress asked NAPAP to assess all available data and information to answer two questions: (1) What are the costs, benefits, and effectiveness of Title IV? This question addresses the costs and economic impacts of complying with the Acid Rain Program as well as benefit analyses associated with the various human health and welfare effects, including reduced visibility, damages to materials and cultural resources, and effects on ecosystems. (2) What reductions in deposition rates are needed to prevent adverse ecological effects? This complex questions addresses ecological systems and the deposition levels at which they experience harmful effects. The results of the assessment of the effects of Title IV and of the relationship between acid deposition rates and ecological effects were to be reported to Congress quadrennially, beginning with the 1996 report to Congress. The objective of this Report is to address the two main questions posed by Congress and fully communicate the results of the assessment to decision-makers. Given the primary audience, most of this report is not written as a technical document, although information supporting the conclusions is provided along with references.

  13. A theoretical study of the interference from chlorine in the oxidative coulometric method for trace determination of sulphur in hydrocarbons.

    Science.gov (United States)

    Cedergren, A

    1975-12-01

    A theoretical investigation has been made of the interference from chlorine in the oxidative coulometric method for trace sulphur determinations. A computer program (SOLGAS), based on the free-energy minimization principle, has been used to predict equilibrium compositions of the products resulting from combustion of a hydrocarbon sample containing sulphur and chlorine. The theoretical possibilities of overcoming the interference from chlorine and maintaining a high recovery of sulphur are described.

  14. Peracetic acid is an optimal disinfectant for fish-microalgae integrated multi-trophic aquaculture systems

    Science.gov (United States)

    Integrated multi-trophic aquaculture is a promising direction for the sustainable development of aquaculture. Instead of releasing nutrition-rich waste to the environment or decomposition of nutrients via the biofilter, the ‘waste’ from fish can be recycled to produce byproducts (e.g., algae, plants...

  15. Technology development for phosphoric acid fuel cell powerplant (phase 2). [on site integrated energy systems

    Science.gov (United States)

    Christner, L.

    1980-01-01

    Progress is reported in the development of material, cell components, and reformers for on site integrated energy systems. Internal resistance and contact resistance were improved. Dissolved gases (O2, N2, and CO2) were found to have no effect on the electrochemical corrosion of phenolic composites. Stack performance was increased by 100 mV over the average 1979 level.

  16. A fully integrated paperfluidic molecular diagnostic chip for the extraction, amplification, and detection of nucleic acids from clinical samples.

    Science.gov (United States)

    Rodriguez, Natalia M; Wong, Winnie S; Liu, Lena; Dewar, Rajan; Klapperich, Catherine M

    2016-02-21

    Paper diagnostics have successfully been employed to detect the presence of antigens or small molecules in clinical samples through immunoassays; however, the detection of many disease targets relies on the much higher sensitivity and specificity achieved via nucleic acid amplification tests (NAAT). The steps involved in NAAT have recently begun to be explored in paper matrices, and our group, among others, has reported on paper-based extraction, amplification, and detection of DNA and RNA targets. Here, we integrate these paper-based NAAT steps into a single paperfluidic chip in a modular, foldable system that allows for fully integrated fluidic handling from sample to result. We showcase the functionality of the chip by combining nucleic acid isolation, isothermal amplification, and lateral flow detection of human papillomavirus (HPV) 16 DNA directly from crude cervical specimens in less than 1 hour for rapid, early detection of cervical cancer. The chip is made entirely of paper and adhesive sheets, making it low-cost, portable, and disposable, and offering the potential for a point-of-care molecular diagnostic platform even in remote and resource-limited settings.

  17. Seasonal and annual deposition rates of sulphur, nitrogen and chloride species to an oak forest in north-eastern austria (wolkersdorf, 240 m a.s.l.)

    Science.gov (United States)

    Puxbaum, Hans; Gregori, Martin

    Dry deposition estimates of sulphur, nitrogen and chloride components to an oak forest in north-eastern Austria were performed using an "Inferential model." The deposition calculations were performed with a modified Hicks et al. (1985) model based on chemical measurement data with 0.5 h (SO 2, NO, NO 2) and 24 h (HCl, HNO 3, NH 3, particulate chloride, nitrate, sulphate and ammonium) time resolution. Annual dry deposition rates of sulphur (SO 2+pSO 4) were estimated to amount around 13 kg ha -1, of oxidised nitrogen (NO+NO 2+HNO 3+pNO 3) 8.4 kg ha -1, of reduced nitrogen (NH 3+pNH 4) 5.6 kg ha -1 and of chloride (HCl+pCl) 2.1 kg ha -1. The relative contribution of dry to total (dry+wet) deposition is 68% for sulphur, 77% for oxidised nitrogen, 55% for reduced nitrogen and 40% for chloride species. Total deposition of sulphur and reduced nitrogen species showed good agreement with data from throughfall measurements and a canopy exchange model. For oxidised nitrogen species the inferential modeling approach yielded a considerably higher deposition which could be explained by the inability of the canopy exchange model to account for stomatal uptake of NO 2. A comparison of dry and wet fluxes of sulphur and nitrogen species at European and U.S. sites indicates that in both environments large regional differences occur. Thus the hypothesis, that European forests receive substantially higher inputs of "major ions" than U.S. forests ( Lindberg et al., 1990) cannot be generalised. "Dry+wet" deposition of nitrogen species at two Austrian sites is well within the range of deposition at 11 forested sites in the U.S., while at one Austrian site it is slightly higher than the highest N-deposition reported for U.S. sites. Compared sites from the U.S. are from the Mountain Cloud Chemistry Project and the Integrated Forest Study ( Lovett and Lindberg, 1993).

  18. 'Integration'

    DEFF Research Database (Denmark)

    Olwig, Karen Fog

    2011-01-01

    After a long history dominated by out-migration, Denmark, Norway and Sweden have, in the past 50 years, become immigration societies. This article compares how these Scandinavian welfare societies have sought to incorporate immigrants and refugees into their national communities. It suggests that......, while the countries have adopted disparate policies and ideologies, differences in the actual treatment and attitudes towards immigrants and refugees in everyday life are less clear, due to parallel integration programmes based on strong similarities in the welfare systems and in cultural notions...... of equality in the three societies. Finally, it shows that family relations play a central role in immigrants’ and refugees’ establishment of a new life in the receiving societies, even though the welfare society takes on many of the social and economic functions of the family....

  19. Assessment of nitrogen and sulphur cycle bacteria and shrimp production in ponds treated with biological products

    Institute of Scientific and Technical Information of China (English)

    Thangapalam Jawahar Abraham; Shubhadeep Ghosh; Debasis Sasmal

    2015-01-01

    Objective:To study the influence of biological products on the levels of nitrogen and sulphur cycle bacteria in shrimp culture systems of West Bengal, India. Methods: The pond water and sediment samples were analyzed for physico-chemical parameters as per standard methods. The bacteria involved in ammonification, nitrification, denitrification, sulphate reduction and sulphur oxidation were enumerated by most probable number technique. Results:The semi-intensive and modified extensive shrimp farms used a variety of biological products during various stages of production. No biological products were used in traditional farms. The water and sediment samples of modified extensive system recorded significantly higher mean heterotrophic bacterial counts. The counts of ammonia, nitrite and sulphur oxidizers, and nitrate and sulphate reducers varied among the systems. The cycling of nitrogen and sulphur appeared to be affected with the intensification of culture practices. Conclusions:The application of biological products in certain systems helped to maintain the bacteria involved in nitrogen and sulphur cycles and safe levels of ammonia, nitrite and nitrate. An assessment of these metabolically active bacteria in shrimp culture ponds and the application of right kind microbial products would help ameliorate the organic pollution in shrimp aquaculture.

  20. Isotopic links between atmospheric chemistry and the deep sulphur cycle on Mars.

    Science.gov (United States)

    Franz, Heather B; Kim, Sang-Tae; Farquhar, James; Day, James M D; Economos, Rita C; McKeegan, Kevin D; Schmitt, Axel K; Irving, Anthony J; Hoek, Joost; Dottin, James

    2014-04-17

    The geochemistry of Martian meteorites provides a wealth of information about the solid planet and the surface and atmospheric processes that occurred on Mars. The degree to which Martian magmas may have assimilated crustal material, thus altering the geochemical signatures acquired from their mantle sources, is unclear. This issue features prominently in efforts to understand whether the source of light rare-earth elements in enriched shergottites lies in crustal material incorporated into melts or in mixing between enriched and depleted mantle reservoirs. Sulphur isotope systematics offer insight into some aspects of crustal assimilation. The presence of igneous sulphides in Martian meteorites with sulphur isotope signatures indicative of mass-independent fractionation suggests the assimilation of sulphur both during passage of magmas through the crust of Mars and at sites of emplacement. Here we report isotopic analyses of 40 Martian meteorites that represent more than half of the distinct known Martian meteorites, including 30 shergottites (28 plus 2 pairs, where pairs are separate fragments of a single meteorite), 8 nakhlites (5 plus 3 pairs), Allan Hills 84001 and Chassigny. Our data provide strong evidence that assimilation of sulphur into Martian magmas was a common occurrence throughout much of the planet's history. The signature of mass-independent fractionation observed also indicates that the atmospheric imprint of photochemical processing preserved in Martian meteoritic sulphide and sulphate is distinct from that observed in terrestrial analogues, suggesting fundamental differences between the dominant sulphur chemistry in the atmosphere of Mars and that in the atmosphere of Earth.

  1. Survival patterns of Dekkera bruxellensis in wines and inhibitory effect of sulphur dioxide.

    Science.gov (United States)

    Barata, A; Caldeira, J; Botelheiro, R; Pagliara, D; Malfeito-Ferreira, M; Loureiro, V

    2008-01-31

    The wine spoilage yeast species Dekkera bruxellensis, after inoculation in red wines, displayed three survival patterns characterized by: i) initial lag phase followed by growth and sequential death; ii) initial death phase leading to reduced viable counts followed by growth and sequential death; and iii) death phase leading to complete loss of viability. These survival patterns were observed for the same strain in different dry red wine blends with 12% (v/v) ethanol and pH 3.50, in the absence of free sulphur dioxide. For the same wine blend, these patterns also varied with the tested strain. Under laboratory conditions the addition of 150 mg/l of potassium metabisulphite (PMB) to dry red wine with 12% (v/v) ethanol and pH 3.50 reduced initial cell counts by more than 6 logarithmic cycles, inducing full death within less than 24 h. Winery trials showed that D. bruxellensis blooms were only prevented in the presence of about 40 mg/l of free sulphur dioxide in dry red wine, with 13.8% (v/v) ethanol and pH 3.42, matured in oak barrels. These different amounts of PMB and sulphur dioxide corresponded to about 1 mg/l of molecular sulphur dioxide. Our results therefore demonstrate that the control of populations of D. bruxellensis growing in red wine can only be achieved under the presence of relatively high doses of molecular sulphur dioxide.

  2. Contributions of polyunsaturated fatty acids (PUFA) on cerebral neurobiology: an integrated omics approach with epigenomic focus

    Science.gov (United States)

    2016-12-01

    November 2016; accepted 15 December 2016Abstract The epigenetic landscape is vulnerable to diets. Here, we investigated the influence of different...accredited by the Association for the Assessment and Accreditation of Laboratory Animal Care, International. The protocol was approved by the IACUC...brain molecular landscape [33]. The left hemibrains were collected for multiomics analysis. For nucleic acid extraction, ice cold hemibrain in Trizol

  3. Clinical validation of integrated nucleic acid and protein detection on an electrochemical biosensor array for urinary tract infection diagnosis.

    Directory of Open Access Journals (Sweden)

    Ruchika Mohan

    Full Text Available BACKGROUND: Urinary tract infection (UTI is a common infection that poses a substantial healthcare burden, yet its definitive diagnosis can be challenging. There is a need for a rapid, sensitive and reliable analytical method that could allow early detection of UTI and reduce unnecessary antibiotics. Pathogen identification along with quantitative detection of lactoferrin, a measure of pyuria, may provide useful information towards the overall diagnosis of UTI. Here, we report an integrated biosensor platform capable of simultaneous pathogen identification and detection of urinary biomarker that could aid the effectiveness of the treatment and clinical management. METHODOLOGY/PRINCIPAL FINDINGS: The integrated pathogen 16S rRNA and host lactoferrin detection using the biosensor array was performed on 113 clinical urine samples collected from patients at risk for complicated UTI. For pathogen detection, the biosensor used sandwich hybridization of capture and detector oligonucleotides to the target analyte, bacterial 16S rRNA. For detection of the protein biomarker, the biosensor used an analogous electrochemical sandwich assay based on capture and detector antibodies. For this assay, a set of oligonucleotide probes optimized for hybridization at 37°C to facilitate integration with the immunoassay was developed. This probe set targeted common uropathogens including E. coli, P. mirabilis, P. aeruginosa and Enterococcus spp. as well as less common uropathogens including Serratia, Providencia, Morganella and Staphylococcus spp. The biosensor assay for pathogen detection had a specificity of 97% and a sensitivity of 89%. A significant correlation was found between LTF concentration measured by the biosensor and WBC and leukocyte esterase (p<0.001 for both. CONCLUSION/SIGNIFICANCE: We successfully demonstrate simultaneous detection of nucleic acid and host immune marker on a single biosensor array in clinical samples. This platform can be used for

  4. Concentration levels and spatial distribution of sulphur and metals in fine-grained sediments in western Finland

    Directory of Open Access Journals (Sweden)

    M. ÅSTRÖM

    2008-12-01

    Full Text Available On the coastal plains of Finland, widespread Holocene marine and lacustrine sediments have developed into acid sulphate soil as a result of extensive artificial drainage for agricultural purposes. This has caused a variety of environmental problems. The aim of this study was to determine the concentration levels and spatial distribution of sulphur, carbon and metals [titanium, vanadium, chromium, manganese (Mn, iron, cobalt (Co, nickel (Ni, copper (Cu, zinc (Zn] in these sediments, in order to increase the geochemical understanding of the parent materials from which acid sulphate soil develops. Sediment samples were collected at 317 sites from a depth of 1.5–3 m. While the sediments have high S (sulphide concentrations (median = 0.54% and thus a strong acidification potential, they carry transition metals mainly in smallsized silicates close to “background concentrations” far below contamination limits. The previously documented extensive release of Co, Cu, Mn, Ni and Zn from oxidised and acidified layers of these sediments (i.e. acid sulphate soil is thus not explained by anomalously high natural or anthropogenic metal concentrations of the soils/sediments, but by an inherent highly mobile metal pool. Spatial-distribution maps highlight areas of elevated S and Mn concentrations, where it is likely that ditching and subsequent oxidation will result in an exceptionally large release of protons and Mn respectively.;

  5. The 2016 Al-Mishraq sulphur plant fire: source and risk area estimation

    CERN Document Server

    Björnham, Oscar; von Schoenberg, Pontus; Waleij, Annica; Liljedahl, Birgitta; Brännström, Niklas

    2016-01-01

    On October 20:th 2016, Daesh (Islamic State) set fire to the sulphur production site Al-Mishraq as the battle of Mosul became more intense. A huge plume of toxic sulphur dioxide and hydrogen sulphide caused comprising casualties. The intensity of the release was reaching levels of minor volcanic eruptions which was observed by several satellites. By investigation of the measurement data from the MetOp-A, MetOp-B, Aura, and Meteosat-10 satellites we have estimated the time-dependent source term for sulphur dioxide which in total amounted to 271 kton released into the atmosphere during six days. The long-range dispersion model PELLO was utilized to simulate the atmospheric transport over the Middle East. The ground-level concentrations predicted by the simulation were validated against observation from the Turkey National Air Quality Monitoring Network. Finally, the simulation data provided an estimate of the risk area using a probit analysis.

  6. Continental Scale Antarctic deposition of sulphur and black carbon from anthropogenic and volcanic sources

    Directory of Open Access Journals (Sweden)

    H.-F. Graf

    2009-12-01

    Full Text Available While Antarctica is often described as a pristine environment, the potential threats from local pollution sources including tourist ships and emissions associated with scientific activities have recently been raised. However, to date there has been no systematic attempt to model the impacts of such pollutants at the continental scale. Indeed, until very recently there was not even a sulphur emission budget available for Antarctica. Here we present the first comprehensive study of atmospheric pollution in Antarctica using a limited area chemistry climate model, and a monthly emissions inventory for sulphur from maintenance of research stations, ground and air traffic, shipping and the active volcano Mt. Erebus. We find that ship emissions, both sulphurous and black carbon, dominate anthropogenic pollution near the ground. These are likely to rise considerably if recent trends in tourism continue.

  7. Structure and compatibility of a magnesium electrolyte with a sulphur cathode.

    Science.gov (United States)

    Kim, Hee Soo; Arthur, Timothy S; Allred, Gary D; Zajicek, Jaroslav; Newman, John G; Rodnyansky, Alexander E; Oliver, Allen G; Boggess, William C; Muldoon, John

    2011-08-09

    Magnesium metal is an ideal rechargeable battery anode material because of its high volumetric energy density, high negative reduction potential and natural abundance. Coupling Mg with high capacity, low-cost cathode materials such as electrophilic sulphur is only possible with a non-nucleophilic electrolyte. Here we show how the crystallization of the electrochemically active species formed from the reaction between hexamethyldisilazide magnesium chloride and aluminum trichloride enables the synthesis of a non-nucleophilic electrolyte. Furthermore, crystallization was essential in the identification of the electroactive species, [Mg(2)(μ-Cl)(3)·6THF](+), and vital to improvements in the voltage stability and coulombic efficiency of the electrolyte. X-ray photoelectron spectroscopy analysis of the sulphur electrode confirmed that the electrochemical conversion between sulphur and magnesium sulfide can be successfully performed using this electrolyte.

  8. Continental scale Antarctic deposition of sulphur and black carbon from anthropogenic and volcanic sources

    Directory of Open Access Journals (Sweden)

    H.-F. Graf

    2010-03-01

    Full Text Available While Antarctica is often described as a pristine environment, there is an increasing awareness of the potential threats from local pollution sources including tourist ships and emissions associated with scientific activities. However, to date there has been no systematic attempt to model the impacts of such pollutants at the continental scale. Indeed, until very recently there was not even a sulphur emission budget available for Antarctica. Here we present the first comprehensive study of atmospheric pollution in Antarctica using a limited area chemistry climate model, and a monthly emissions inventory for sulphur from maintenance of research stations, ground and air traffic, shipping and the active Erebus volcano. We find that ship emissions, both sulphurous and black carbon, dominate anthropogenic pollution near the ground. Their prevalence is likely to rise dramatically if recent trends in tourism continue.

  9. A modified oxidative microcoulometric method for determination of sulphur in hydrocarbons containing large amounts of chlorine.

    Science.gov (United States)

    Cedergren, A

    1977-01-01

    The oxidative coulometric method for trace sulphur determinations has been modified and a procedure is described which includes the elimination of the interferences caused by chlorine whilst retaining a high recovery of sulphur. The liquid hydrocarbon sample is combusted in an excess of oxygen at 1000 K followed by dilution with a proper flow of carbon monoxide at 1300 K. In this way the partial pressure of oxygen is kept small and the interfering chlorine compounds are effectively converted into hydrogen chloride which does not interfere with the coulometric titration. A recovery of sulphur of 96 +/- 1% was found for thiophene in mixtures of chlorobenzene (0-10%) and cyclohexane, thus indicating the absence of significant interference.

  10. Manganese modified zeolite silicalite-1 as polysulphide sorbent in lithium sulphur batteries

    Science.gov (United States)

    Lapornik, Vida; Novak Tusar, Natasa; Ristic, Alenka; Chellappan, Rajesh Kumar; Foix, Dominique; Dedryvère, Rémi; Gaberscek, Miran; Dominko, Robert

    2015-01-01

    Discharge/charge process of classical lithium sulphur battery proceeds through intermediate polysulphides which are soluble in classical electrolyte systems. Due to concentration gradient soluble polysulphides easily diffuse/migrate out from cathode composite forming non-uniform distribution of the sulphur within cathode. Eventually polysulphides can be completely reduced on the metallic lithium anode. In this work we compare the sorption properties of manganese modified zeolite silicalite-1 (MnS-1) with a cathode composite containing SBA-15 additive and a cathode composite without additive. Careful analysis using XPS and FIB microscopy equipped with EDX show improved retention of polysulphide species within cathode composite in the case of MnS-1 zeolite as an additive. Interestingly, the amount of sulphur species detected by XPS on the metallic lithium is very similar regardless on cathode composite we use. Finally, similar cycling behaviour can be observed if MnS-1 zeolite is used as an interlayer between composite cathode and separator.

  11. The disposal of flue gas desulphurisation waste: sulphur gas emissions and their control.

    Science.gov (United States)

    Raiswell, R; Bottrell, S H

    1991-06-01

    Flue gas desulphurisation (FGD) equipment to be fitted to UK coal-fired power stations will produce more than 0.8 Mtonnes of calcium sulphate, as gypsum. Most gypsum should be of commercial quality, but any low grade material disposed as waste has the potential to generate a range of sulphur gases, including H2S, COS, CS2, DMS and DMDS. Literature data from the USA indicates that well-oxidised waste with a high proportion of calcium sulphate (the main UK product of FGD) has relatively low emissions of sulphur gases, which are comparable to background levels from inland soils. However, sulphur gas fluxes are greatly enhanced where reducing conditions become established within the waste, hence disposal strategies should be formulated to prevent the sub-surface consumption of oxygen.

  12. Process integration for the conversion of glucose to 2,5-furandicarboxylic acid

    DEFF Research Database (Denmark)

    Boisen, A.; Christensen, T.B.; Fu, Wenjing

    2009-01-01

    The development of biorefineries means that a key feedstock for many new processes will be sugars in various forms, such as glucose or fructose. From these feedstocks a range of chemicals can be synthesized using heterogeneous catalysis, immobilized enzymes, homogeneous catalysts, soluble enzymes......, fermentations or combinations thereof. This presents a particularly interesting process integration challenge since the optimal conditions for each conversion step will be considerably different from each other. Furthermore, compared to oil-based refineries the feedstock represents a relatively high proportion...

  13. Utilización de azufre micronizado en la corrección del pH de compost de residuos de poda Correction of the pH of pruning waste compost with micronized sulphur

    Directory of Open Access Journals (Sweden)

    L.A. Barbaro

    2010-12-01

    Full Text Available Los compost actualmente son muy utilizados como componentes de sustratos, aunque en algunos casos presentan pH alcalinos y causan problemas nutricionales. Por ello se recomienda hacer una corrección previa a su utilización o luego de elaborar el sustrato. Algunas alternativas para bajar el pH es mezclando el compost con materiales ácidos o mediante la adición de azufre, sulfato ferroso u otros compuestos azufrados. El objetivo de este trabajo fue corregir el pH de un compost de residuos de poda con azufre micronizado y hallar la dosis adecuada para el pH deseado. Se conformaron siete tratamientos, incorporando al compost de poda diferentes dosis de azufre micronizado: 0, 1, 2, 3, 4, 6 y 8 g/litro. Al compost de cada tratamiento se le midió el pH semanalmente y una vez estabilizados se analizó la conductividad eléctrica, concentración de nitrato, calcio, magnesio, potasio y sodio. Para un pH entre 5,3 y 6,2 se necesitaron 2 a 3 g de azufre/litro. El pH del compost disminuyó con el incremento de la dosis de azufre, y la CE aumentó. El azufre micronizado es una alternativa viable para corregir el pH del compost de restos de poda a los valores deseados.Nowadays, composts are widely used for incorporation into substrates and in some cases they present alkaline pH, causing nutritional problems. Therefore, it is suggested that a correction should be made prior to its use or after its preparation. Some alternatives to decrease pH values are mixing compost with acid materials or adding sulphur, ferrous sulphate or other sulphur compounds. The aim of this work was to correct the pH of pruning waste compost with micronized sulphur and find the appropriate dose for the desired pH. Seven treatments were performed incorporating different doses of micronized sulphur: 0, 1, 2, 3, 4, 6 and 8 g per liter of compost. Compost pH was measured weekly in each treatment. Once stabilized, electrical conductivity and concentration of nitrate, calcium, magnesium

  14. Identifying sources and processes controlling the sulphur cycle in the Canyon Creek watershed, Alberta, Canada.

    Science.gov (United States)

    Nightingale, Michael; Mayer, Bernhard

    2012-01-01

    Sources and processes affecting the sulphur cycle in the Canyon Creek watershed in Alberta (Canada) were investigated. The catchment is important for water supply and recreational activities and is also a source of oil and natural gas. Water was collected from 10 locations along an 8 km stretch of Canyon Creek including three so-called sulphur pools, followed by the chemical and isotopic analyses on water and its major dissolved species. The δ(2)H and δ(18)O values of the water plotted near the regional meteoric water line, indicating a meteoric origin of the water and no contribution from deeper formation waters. Calcium, magnesium and bicarbonate were the dominant ions in the upstream portion of the watershed, whereas sulphate was the dominant anion in the water from the three sulphur pools. The isotopic composition of sulphate (δ(34)S and δ(18)O) revealed three major sulphate sources with distinct isotopic compositions throughout the catchment: (1) a combination of sulphate from soils and sulphide oxidation in the bedrock in the upper reaches of Canyon Creek; (2) sulphide oxidation in pyrite-rich shales in the lower reaches of Canyon Creek and (3) dissolution of Devonian anhydrite constituting the major sulphate source for the three sulphur pools in the central portion of the watershed. The presence of H(2)S in the sulphur pools with δ(34)S values ∼30 ‰ lower than those of sulphate further indicated the occurrence of bacterial (dissimilatory) sulphate reduction. This case study reveals that δ(34)S values of surface water systems can vary by more than 20 ‰ over short geographic distances and that isotope analyses are an effective tool to identify sources and processes that govern the sulphur cycle in watersheds.

  15. Biofertilzers with natural phosphate, sulphur and Acidithiobacillus in a siol with low available-P

    Directory of Open Access Journals (Sweden)

    Stamford Newton Pereira

    2003-01-01

    Full Text Available The production of mineral fertilizers is a expensive process, since it requires high energy consumption, and cannot be produced by small farmers. Laboratory assays were conducted to produce P-biofertilizers from natural phosphate (B5, B10, B15, B20, applying sulphur at different rates (5; 10; 15 and 20% inoculated with Acidithiobacillus (S* and testing increasing periods of incubation. A greenhouse experiment was carried out to evaluate the effect of the biofertilizers in a soil with low available P (Typic Fragiudult from the "Zona da Mata" of Pernambuco State, grown with yam bean (Pachyrhizus erosus in two consecutive harvests. The treatments were: Natural Phosphate (NP; biofertilizers produced in laboratory (B5, B10, B15, B20 with sulphur and Acidithiobacillus (NP+S*; natural phosphate with sulphur (20% without Acidithiobacillus (NP+S; triple super phosphate (TSP and a control without phosphorus. Plants were inoculated with a mixture of rhizobia strains (NFB 747 and NFB 748 or did not receive rhizobia inoculation. In bioassays pH and available P in the biofertilizers were analyzed. In the greenhouse experiment shoot dry matter, total N and total P in shoots, soil pH and available P were determined. Higher rates of available P were obtained in biofertilizers with sulphur and Acidithiobacillus (NP+S* and in triple super phosphate (TSP, and biofertilizers with sulphur and Acidithiobacillus (FN+S* and triple super phosphate (TSP increased plant parameters. Native rhizobia were as effective as the strains applied in inoculation. After the two harvests soil presented lower pH values and higher rates of available P when the biofertilizers B15 and B20 with sulphur and Acidithiobacillus were applied.

  16. Development of a Linear Flow Channel Reactor for sulphur removal ...

    African Journals Online (AJOL)

    2013-09-23

    Sep 23, 2013 ... in acid mine wastewater treatment operations ... 2Department of Biochemistry, Microbiology and Biotechnology, Rhodes University, Grahamstown, 6140, South Africa. ABSTRACT ... and, with certain Roman mine workings in Britain and Europe ... using industrial grade sodium sulphate (Protea Chemicals),.

  17. Atmospheric oxidation of sulphur dioxide in water droplets in presence of ammonia

    Energy Technology Data Exchange (ETDEWEB)

    McKay, H.A.C.

    1971-01-01

    The kinetics of the conversion of ammonia and sulphur dioxide to ammonium sulphate in water droplets in the atmosphere in the absence of metal ion catalysts has been reconsidered. It is concluded that the reaction is an order of magnitude faster than earlier work suggested, and that lowering the temperature increases the rate by a large factor. In a cloud or a thick mist appreciable amounts of ammonium sulphate may be formed in a few minutes; nevertheless a substantial proportion of unreacted ammonia may sometimes persist for hours, even though excess sulphur dioxide is present and the initial reaction is fast.

  18. Rapid total sulphur reduction in coal samples using various dilute alkaline leaching reagents under microwave heating: preventing sulphur emissions during coal processing.

    Science.gov (United States)

    Mketo, Nomvano; Nomngongo, Philiswa Nosizo; Ngila, Jane Catherine

    2017-07-07

    Currently in South Africa, online flue gas desulphurisation (FGD) is being utilized as one of the most effective methods for total sulphur reduction in coal samples during the combustion process. However, the main disadvantage associated with FGD is the formation of its by-products (FGD gypsum). The latter is mostly formed in low grade quality, thereby bringing secondary pollution problems and extra disposal costs. Therefore, the current study describes the development of total sulphur extraction in coal under microwave heating using different dilute alkaline solutions such as NaOH, NaOH-H2O2, NH4OH, and NH4OH-H2O2. The experimental conditions were as follows: 150 °C, 5 min and 10% (m/v or v/v) for temperature, extraction time and reagent concentration, respectively. The most effective alkaline reagent for coal desulphurisation was observed to be NaOH-H2O2 with total sulphur reduction of 55% (from the inductively coupled plasma-optical emission spectrometry (ICP-OES) results). The NaOH-H2O2 reagent also showed significant morphological changes in coal as observed from the SEM images and effective demineralisation as revealed by the powder X-ray diffractometer (P-XRD) results. Additionally, desulphurisation results obtained from the developed microwave-assisted dilute alkaline extraction (MW-ADAE) method were quite comparable with the published work. The proposed total sulphur reduction method is advantageous as compared to some of the literature reported coal desulphurisation methods as it requires a short period (5 min) of time to reach its completion. Additionally, the proposed method shows excellent reproducibility (% RSD from 0.5 to 1); therefore, it can be utilized for routine analysis. Graphical abstract ᅟ.

  19. Lipids and Composition of Fatty Acids of Saccharina latissima Cultivated Year-Round in Integrated Multi-Trophic Aquaculture.

    Science.gov (United States)

    Marinho, Gonçalo S; Holdt, Susan L; Jacobsen, Charlotte; Angelidaki, Irini

    2015-07-15

    This study is evaluating the seasonal lipid and fatty acid composition of the brown seaweed Saccharina latissima. Biomass was sampled throughout the year (bi-monthly) at the commercial cultivation site near a fish farm in an integrated multi-trophic aquaculture (IMTA) and at a reference site in Denmark (2013-2014). Generally, there was no difference in the biomass composition between sites; however, significant seasonal changes were found. The lipid concentration varied from 0.62%-0.88% dry weight (DW) in July to 3.33%-3.35% DW in November (p seaweed species contains higher proportions of ARA and SDA, but lower EPA (only cod) and DHA. Conclusively, the season of harvest is important for the choice of lipid quantity and quality, but the marine vegetables provide better sources of EPA, DHA and long-chain (LC)-PUFA's in general compared to traditional vegetables.

  20. 77 FR 9962 - Information Collection; Prospecting for Minerals Other Than Oil, Gas, and Sulphur on the Outer...

    Science.gov (United States)

    2012-02-21

    ... Bureau of Ocean Energy Management Information Collection; Prospecting for Minerals Other Than Oil, Gas... paperwork requirements in the regulations under Prospecting for Minerals Other than Oil, Gas, and Sulphur on...: 30 CFR Part 580, Prospecting for Minerals Other than Oil, Gas, and Sulphur on the Outer...

  1. 78 FR 66066 - Proposed Information Collection for OMB Review; Comment Request: Leasing of Sulphur or Oil and...

    Science.gov (United States)

    2013-11-04

    ...: Leasing of Sulphur or Oil and Gas in the Outer Continental Shelf and Pipeline Rights of Way ACTION: 60-day... paperwork requirements in the regulations under 30 CFR 556, Leasing of Sulphur or Oil and Gas in the OCS; 30 CFR 550, Subpart J, Pipelines and Pipeline Rights-of-Way; and 30 CFR 560, OCS Oil and Gas...

  2. Incisional Colopexy for Treatment of Chronic, Recurrent Colocloacal Prolapse in a Sulphur-Crested Cockatoo (Cacatua galerita)

    NARCIS (Netherlands)

    van Zeeland, Yvonne; Schoemaker, Nico; van Sluijs, Freek

    2014-01-01

    Objective To report a surgical technique for treatment of chronic, recurrent cloacal prolapse in a sulphur-crested cockatoo (Cacatua galerita). Study Design Clinical report Animals Sulphur-crested cockatoo (n = 1) Methods The bird was admitted with a 2-year history of periodic lethargy, decreased ap

  3. Dispersion of sulphur in the northern hemisphere. A study with a 3-dimensional time-resolved model

    Energy Technology Data Exchange (ETDEWEB)

    Tarrason, L.

    1995-12-31

    This thesis on atmospheric dispersion of sulphur presents a calculation of intercontinental transport of oxidized sulphur and allocates different contributions to sulphur background levels over Europe. It is found that a significant fraction of anthropogenic sulphur (AS) is transported out of continental boundaries thus affecting the background levels over major parts of the northern hemisphere. Over Europe, the contribution of AS from North America is similar in amount to that of Asian AS and natural sources from the North Atlantic Ocean. Although the yearly contribution of intercontinental transport to deposition of sulphur over Europe is quite small, it can be much more important over certain areas and seasons and is comparable to the contributions from individual European countries. The calculations are based on a three-dimensional Eulerian time-resolved model that describes sulphur dispersion in the atmosphere in connection with large-scale synoptic flows and agree well with observations. The thesis emphasizes the role of synoptic scale atmospheric motions in determining intercontinental transport of sulphur. It indicates the need to resolve individual cyclones and anticyclones in order to describe the dispersion and distribution of atmospheric sulphur in the northern hemisphere and stresses the value of comparing model calculations with observations, both in atmospheric chemistry studies and in climate applications. 260 refs., 50 figs., 17 tabs.

  4. CLINICAL EXPERIENCE OF CANCER IMMUNOTHERAPY INTEGRATED WITH OLEIC ACID COMPLEXED WITH DE-GLYCOSYLATED VITAMIN D BINDING PROTEIN

    Directory of Open Access Journals (Sweden)

    Emma Ward

    2014-01-01

    Full Text Available Proteins highly represented in milk such as α-lactalbumin and lactoferrin bind Oleic Acid (OA to form complexes with selective anti-tumor activity. A protein present in milk, colostrum and blood, vitamin D binding protein is the precursor of a potent Macrophage Activating Factor (GcMAF and in analogy with other OA-protein complexes, we proposed that OA-GcMAF could demonstrate a greater immunotherapeutic activity than that of GcMAF alone. We describe a preliminary experience treating patients with advanced cancers, often labelled as “incurable” with an integrative immunotherapy centred on OA-GcMAF. Patients with advanced cancer were treated at the Immuno Biotech Treatment Centre with OA-GcMAF-based integrative immunotherapy in combination with a very low carbohydrate, high protein diet, fermented milk products containing naturally produced GcMAF, vitamin D3 and low-dose acetylsalicylic acid. When the primary tumor or a metastasis could be measured by ultrasonographic techniques, we observed, on average, a decrease of tumor volume of approximately 25% in a week. We also observed a consistent increase in splenic blood flow that was interpreted in the context of generalised immune system activation and allowed to assess the degree of responsiveness of the individual patient. The results reported here are consistent with the results previously described in the experimental animal harbouring a human hepatocellular carcinoma as well as with the results reported for neoadjuvant chemotherapy. OA-protein complexes are bound to play a leading role in cancer therapy thanks to selectivity of antitumoral effects, absence of any side effects, safety and oral availability. We hypothesise that OA-GcMAF, combines the known anticancer effects OA-protein complexes with the well established immune stimulating effects of GcMAF.

  5. Endothelium-derived hyperpolarization and coronary vasodilation: diverse and integrated roles of epoxyeicosatrienoic acids, hydrogen peroxide and gap junctions

    Science.gov (United States)

    Ellinsworth, David C.; Sandow, Shaun L.; Shukla, Nilima; Liu, Yanping; Jeremy, Jamie Y.; Gutterman, David D.

    2015-01-01

    Myocardial perfusion and coronary vascular resistance are regulated by signalling metabolites released from the local myocardium that act either directly on the vascular smooth muscle cells (VSMC) or indirectly via stimulation of the endothelium. A prominent mechanism of vasodilation is endothelium-derived hyperpolarization (EDH) of the arteriolar smooth muscle, with epoxyeicosatrienoic acids (EETs) and hydrogen peroxide (H2O2) playing important roles in EDH in the coronary microcirculation. In some cases, EETs and H2O2 are released as transferable hyperpolarizing factors (EDHFs) that act directly on the VSMCs. By contrast, EETs and H2O2 can also promote endothelial Ca2+-activated K+ channel activity secondary to the amplification of extracellular Ca2+ influx and Ca2+ mobilization from intracellular stores, respectively. The resulting endothelial hyperpolarization may subsequently conduct to the media via myoendothelial gap junctions, or potentially lead to the release of a chemically-distinct factor(s). Furthermore, in human isolated coronary arterioles dilator signalling involving EETs and H2O2 may be integrated; being either complimentary or inhibitory depending on the stimulus. With an emphasis on the human coronary microcirculation, this review addresses the diverse and integrated mechanisms by which EETs and H2O2 regulate vessel tone, and also examines the hypothesis that myoendothelial microdomain signalling facilitates EDH activity in the human heart. PMID:26541094

  6. Integrated isolation and quantitative analysis of exosome shuttled proteins and nucleic acids using immunocapture approaches.

    Science.gov (United States)

    Zarovni, Natasa; Corrado, Antonietta; Guazzi, Paolo; Zocco, Davide; Lari, Elisa; Radano, Giorgia; Muhhina, Jekatarina; Fondelli, Costanza; Gavrilova, Julia; Chiesi, Antonio

    2015-10-01

    Clinical implementation of exosome based diagnostic and therapeutic applications is still limited by the lack of standardized technologies that integrate efficient isolation of exosomes with comprehensive detection of relevant biomarkers. Conventional methods for exosome isolation based on their physical properties such as size and density (filtration, ultracentrifugation or density gradient), or relying on their differential solubility (chemical precipitation) are established primarily for processing of cell supernatants and later adjusted to complex biological samples such as plasma. Though still representing gold standard in the field, these methods are clearly suboptimal for processing of routine clinical samples and have intrinsic limits that impair their use in biomarker discovery and development of novel diagnostics. Immunoisolation (IA) offers unique advantages for the recovery of exosomes from complex and viscous fluids, in terms of increased efficiency and specificity of exosome capture, integrity and selective origin of isolated vesicles. We have evaluated several commercially available solutions for immunoplate- and immunobead-based affinity isolation and have further optimized protocols to decrease non-specific binding due to exosomes complexity and matrix contaminants. In order to identify best molecular targets for total exosome capture from diverse biological sources, as well as for selective enrichment in populations of interest (e.g. tumor derived exosomes) several exosome displayed proteins and respective antibodies have been evaluated for plate and bead functionalisation. Moreover, we have optimized and directly implemented downstream steps allowing on-line quantification and characterization of bound exosome markers, namely proteins and RNAs. Thus assembled assays enabled rapid overall quantification and validation of specific exosome associated targets in/on plasma exosomes, with multifold increased yield and enrichment ratio over benchmarking

  7. Methoxistasis: integrating the roles of homocysteine and folic acid in cardiovascular pathobiology.

    Science.gov (United States)

    Joseph, Jacob; Loscalzo, Joseph

    2013-08-15

    Over the last four decades, abnormalities in the methionine-homocysteine cycle and associated folate metabolism have garnered great interest due to the reported link between hyperhomocysteinemia and human pathology, especially atherothrombotic cardiovascular disease. However, clinical trials of B-vitamin supplementation including high doses of folic acid have not demonstrated any benefit in preventing or treating cardiovascular disease. In addition to the fact that these clinical trials may have been shorter in duration than appropriate for modulating chronic disease states, it is likely that reduction of the blood homocysteine level may be an oversimplified approach to a complex biologic perturbation. The methionine-homocysteine cycle and folate metabolism regulate redox and methylation reactions and are, in turn, regulated by redox and methylation status. Under normal conditions, a normal redox-methylation balance, or "methoxistasis", exists, coordinated by the methionine-homocysteine cycle. An abnormal homocysteine level seen in pathologic states may reflect a disturbance of methoxistasis. We propose that future research should be targeted at estimating the deviation from methoxistasis and how best to restore it. This approach could lead to significant advances in preventing and treating cardiovascular diseases, including heart failure.

  8. Planning of an Integrated Acidification Study and Survey on Acid Rain Impacts in China. Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Lydersen, Espen; Angell, Valter; Eilertsen, Odd; Muniz, Ivar P. [Norsk Inst. for Naturforskning, Trondheim (Norway); Larssen, Thorbjoern; Seip, Hans Martin; Aagaard, Per; Vogt, Rolf D. [Oslo Univ. (Norway); Mulder, Jan

    1997-12-31

    This is the final report from the PIAC project, which was a multidisciplinary survey on acid rain in China. One goal was to document effects of airborne acidifying compounds on vegetation, soil, soil- and surface-water and aquatic biota. Other goals were to exchange knowledge between Chinese and Norwegian scientists, and to visit research sites in highly polluted areas in China and evaluate their need of support in a future collaborative monitoring and research programme. Samples have been collected from over 20 sites in three areas. Negative effects of air pollution are found on all ecosystem levels investigated. The concentration of sulfur in the air in urban and near-urban areas is very high. The concentration of volatile organic compounds is generally high, which means that increased NOx emissions in coming years may increase the ozone problems. Reduced photosynthesis activities were found in some plants and acidification observed in soil and surface water. Aquatic biota also reflect the acidification status of the surface waters investigated. However, it is difficult to assess the degree of damage in these regions because the survey includes too few sites. Surface water acidification is currently not a major environmental problem in China and is unlikely to be one during the next decades. The report includes a status report on acidification in China and a proposed framework for a monitoring programme based on Norwegian experiences. 139 refs., 16 figs., 45 tabs.

  9. Short communication: Differential loss of bovine mammary epithelial barrier integrity in response to lipopolysaccharide and lipoteichoic acid.

    Science.gov (United States)

    Wellnitz, Olga; Zbinden, Christina; Huang, Xiao; Bruckmaier, Rupert M

    2016-06-01

    In the mammary gland, the blood-milk barrier prevents an uncontrolled intermixture of blood and milk constituents and hence maintains the osmotic gradient to draw water into the mammary secretion. During mastitis, the permeability of the blood-milk barrier is increased, which is reflected by the transfer of blood constituents into milk and vice versa. In this study, we aimed to investigate changes in the barrier function of mammary epithelial cells in vitro as induced by cell wall components of different pathogens. Primary bovine mammary epithelial cells from 3 different cows were grown separately on Transwell (Corning Inc., Corning, NY) inserts. The formation of tight junctions between adjacent epithelial cells was shown by transmission electron microscopy and by immunofluorescence staining of the tight junction protein zona occludens-1. The integrity of the epithelial barrier was assayed by means of transepithelial electrical resistance, as well as by diffusion of the fluorophore Lucifer yellow across the cell layer. The release of lactate dehydrogenase (LDH) was used as an indicator for cytotoxic effects. In response to a 24-h challenge with bacterial endotoxin, barrier integrity was reduced after 3 or 7h, respectively, in response to 0.5mg/mL lipopolysaccharide (LPS) from Escherichia coli or 20mg/mL lipoteichoic acid (LTA) from Staphylococcus aureus. No paracellular leakage was observed in response to 0.2mg/mL LPS or 2mg/mL LTA. Although LPS and LTA affected barrier permeability, most likely by opening the tight junctions, only LPS caused cell damage, reflected by increased LDH concentrations in cell culture medium. These results prove a pathogen-specific loss of blood-milk barrier integrity during mastitis, which is characterized by tight junction opening by both LPS and LTA and by additional epithelial cell destruction through LPS. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

  10. Transcriptome profiling identifies candidate genes associated with the accumulation of distinct γ-glutamyl sulphur dipeptides in Phaseolus vulgaris and Vigna mungo seeds

    Directory of Open Access Journals (Sweden)

    Dengqun eLiao

    2013-03-01

    Full Text Available Common bean (Phaseolus vulgaris and black gram (Vigna mungo accumulate γ-glutamyl-S-methylcysteine and γ-glutamyl-methionine in seed, respectively. Transcripts were profiled by 454 pyrosequencing at a similar developmental stage coinciding with the beginning of the accumulation of these metabolites. Expressed sequence tags were assembled into Unigenes, which were assigned to specific genes in the early release chromosomal assembly of the P. vulgaris genome. Genes involved in multiple sulphur metabolic processes were expressed in both species. Expression of Sultr3 members was predominant in P. vulgaris, whereas expression of Sultr5 members predominated in V. mungo. Expression of the cytosolic SERAT1;1 and -1;2 was approximately four-fold higher in P. vulgaris while expression of the plastidic SERAT2;1 was two-fold higher in V. mungo. Among BSAS family members, BSAS4;1, encoding a cytosolic cysteine desulphydrase, and BSAS1;1, encoding a cytosolic O-acetylserine sulphydrylase were most highly expressed in both species. This was followed by BSAS3;1 encoding a plastidic β-cyanoalanine synthase which was more highly expressed by 10-fold in P. vulgaris. The data identify BSAS3;1 as a candidate enzyme for the biosynthesis of S-methyl-cysteine through the use of methanethiol as substrate instead of cyanide. Expression of GLC1 would provide a complete sequence leading to the biosynthesis of γ-glutamyl-S-methylcysteine in plastids. The detection of S-methylhomoglutathione in P. vulgaris suggested that homoglutathione synthetase may accept, to some extent, γ-glutamyl-S-methylcysteine as substrate, which might lead to the formation of S-methylated phytochelatins. In conclusion, 454 sequencing was effective at revealing differences in the expression of sulphur metabolic genes, providing information on candidate genes for the biosynthesis of distinct sulphur amino acid γ-glutamyl dipeptides between P. vulgaris and V. mungo.

  11. Integrated systems biology analysis of transcriptomes reveals candidate genes for acidity control in developing fruits of sweet orange (Citrus sinensis L. Osbeck

    Directory of Open Access Journals (Sweden)

    Dingquan eHuang

    2016-04-01

    Full Text Available Organic acids, such as citrate and malate, are important contributors for the sensory traits of fleshy fruits. Although their biosynthesis has been illustrated, regulatory mechanisms of acid accumulation remain to be dissected. To provide transcriptional architecture and identify candidate genes for citrate accumulation in fruits, we have selected for transcriptome analysis four varieties of sweet orange (Citrus sinensis L. Osbeck with varying fruit acidity, Succari (acidless, Bingtang (low acid, and Newhall and Xinhui (normal acid. Fruits of these varieties at 45 days post anthesis (DPA, which corresponds to Stage I (cell division, had similar acidity, but they displayed differential acid accumulation at 142 DPA (Stage II, cell expansion. Transcriptomes of fruits at 45 and 142 DPA were profiled using RNA sequencing and analyzed with three different algorithms (Pearson correlation, gene coexpression network and surrogate variable analysis. Our network analysis shows that the acid-correlated genes belong to three distinct network modules. Several of these candidate fruit acidity genes encode regulatory proteins involved in transport (such as AH10, degradation (such as APD2 and transcription (such as AIL6 and act as hubs in the citrate accumulation gene networks. Taken together, our integrated systems biology analysis has provided new insights into the fruit citrate accumulation gene network and led to the identification of candidate genes likely associated with the fruit acidity control.

  12. Lung and renal uptake of techneticum Tc 99m sulphur colloid related to disseminated intravascular coagulation

    Energy Technology Data Exchange (ETDEWEB)

    Jelle Teertstra, H.; Verdegaal, W.P.; Ras, G.J.

    1985-01-01

    In addition to a recently published case study, we present another three cases in which we observed both lung and renal uptake of technetium Tc 99m sulphur colloid which was related to a period of disseminated intravascular coagulation. Being familiar with this relationship may influence the diagnosis and course of the illness in certain patients.

  13. Corrosion of stainless steels by sulphur dioxide and chlorine in atmospheric conditions

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, S.; Dhirendra, Dr.; Sanyal, B.; Pandey, G.N.

    1982-10-01

    This paper deals with the effect of sulphur dioxide and chlorine on stainless steels (AISI 304 and 321) under different atmospheric conditions. 70% RH value was found to be critical giving maximum corrosion. Potassium dichromate has been found to be a suitable passivating agent for protection against corrosion due to chlorine. (5 refs.)

  14. Dispersion of sulphur dioxide around the thermal power plant at Ahmedabad, India

    Science.gov (United States)

    Naik, Medha S.

    Air quality due to the release of sulphur dioxide from the thermal power plant within the city limits of Ahmedabad has been computed employing a point, area and line dispersion model. To estimate probable air quality, the meteorological data for 3 consecutive days in the middle of each month of 1983 is used. The concentration of sulphur dioxide is computed at a distance of every 500 m in 16 directions up to the city limit. The air quality in the worst case is estimated in downwind distances under unfavourable meteorological conditions. The probable zones of high concentrations of sulphur dioxide over residential, commercial and industrial areas of the city are below the ambient air quality standards set by the U.S. EPA in 1971 almost throughout the year. However, in the months of April and October the zone of high concentration (500 μg m -3) exceeds the EPA standard. Also, under the most unfavourable meteorological conditions, the estimated high ground-level concentration of sulphur dioxide can reach up to 1000 μg m -3 at a distance of 1.25 km from the thermal power plant. This may be attributed to the effect of fumigation.

  15. Rare isotopic species of sulphur monoxide: the rotational spectrum in the THz region

    CERN Document Server

    Lattanzi, Valerio; Puzzarini, Cristina

    2015-01-01

    Many sulphur-bearing species have been detected in different astronomical environments and have allowed to derive important information about the chemical and physical composition of interstellar regions. In particular, these species have also been showed to trace and probe hot-core environment time evolution. Among the most prominent sulphur-bearing molecules, SO, sulphur monoxide radical, is one of the more ubiquitous and abundant, observed also in its isotopic substituted species such as $^{34}$SO and S$^{18}$O. Due to the importance of this simple diatomic system and to face the challenge of modern radioastronomical facilities, an extension to THz range of the rare isotopologues of sulphur monoxide has been performed. High-resolution rotational molecular spectroscopy has been employed to extend the available dataset of four isotopic species, SO, $^{34}$SO, S$^{17}$O, and S$^{18}$O up to the 1.5 THz region. The frequency coverage and the spectral resolution of our measurements allowed a better constraint o...

  16. 78 FR 42538 - Information Collection Activities: Sulphur Operations, Proposed Collection; Comment Request

    Science.gov (United States)

    2013-07-16

    ... that a discovered sulphur deposit can be classified as capable of production in paying quantities... request. 1605(f) Submit application for installation of Burden covered under (1014- fixed drilling.... deposit can produce in paying quantities. 1605(e)(5) Request copy of directional survey (by 1. holder of...

  17. 75 FR 15718 - MMS Information Collection Activity: 1010-0086, Sulphur Operations, Extension of a Collection...

    Science.gov (United States)

    2010-03-30

    ... Minerals Management Service MMS Information Collection Activity: 1010-0086, Sulphur Operations, Extension... of extension of an information collection (1010-0086). SUMMARY: To comply with the Paperwork...; Herndon, Virginia 20170-4817. Please reference ICR 1010-0086 in your comment and include your name...

  18. Adsorption enhancement of elemental mercury onto sulphur-functionalized silica gel adsorbents.

    Science.gov (United States)

    Johari, Khairiraihanna; Saman, Norasikin; Mat, Hanapi

    2014-01-01

    In this study, elemental mercury (EM) adsorbents were synthesized using tetraethyl orthosilicate (TEOS) and 3-mercaptopropyl trimethoxysilane as silica precursors. The synthesized silica gel (SG)-TEOS was further functionalized through impregnation with elemental sulphur and carbon disulphide (CS2). The SG adsorbents were then characterized by using scanning electron microscope, Fourier transform infra-red spectrophotometer, nitrogen adsorption/desorption, and energy-dispersive X-ray diffractometer. The EM adsorption of the SG adsorbents was determined using fabricated fixed-bed adsorber. The EM adsorption results showed that the sulphur-functionalized SG adsorbents had a greater Hgo breakthrough adsorption capacity, confirming that the presence of sulphur in silica matrices can improve Hgo adsorption performance due to their high affinity towards mercury. The highest Hgo adsorption capacity was observed for SG-TEOS(CS2) (82.62 microg/g), which was approximately 2.9 times higher than SG-TEOS (28.47 microg/g). The rate of Hgo adsorption was observed higher for sulphur-impregnated adsorbents, and decreased with the increase in the bed temperatures.

  19. Rubber composites cured with sulphur and peroxide and incorporated with strontium ferrite

    Indian Academy of Sciences (India)

    JÁN KRUŽELÁK; RASTISLAV DOSOUDIL; RICHARD SÝKORA; IVAN HUDEC

    2017-02-01

    In the present work, rubber magnetic composites were prepared by incorporation of strontium ferrite into rubber matrices based on natural rubber (NR) and acrylonitrile–butadiene rubber (NBR). Sulphur, peroxide and mixed sulphur/peroxide curing systems were introduced in cross-linking of rubber matrices. The aim was to investigate the influence of curing system composition on physical–mechanical, thermo-physical and magnetic properties of prepared rubber composites and the curing process. Then, the determination of cross-link density and the structure of cross-links were under consideration. The achieved results showed that all investigated parameters were changed depending on the composition of curing system, but also on the type of rubber matrix. While the tensile strength of composites based on NR increased with increasing amount of sulphur in mixed curing systems, in case of composites based on NBR, the highest value of tensile strength reached the value of the sample cured with equivalent ratio of sulphur and peroxide. On the other hand, thermo-physical and magnetic characteristics were found not to be dependent on the curing system composition. The results revealed that not only the composition of curingsystem, but also the type of rubber matrix plays an important role when preparing the final materials.

  20. Sulphur-oxidizing and sulphate-reducing communities in Brazilian mangrove sediments.

    Science.gov (United States)

    Varon-Lopez, Maryeimy; Dias, Armando Cavalcante Franco; Fasanella, Cristiane Cipolla; Durrer, Ademir; Melo, Itamar Soares; Kuramae, Eiko Eurya; Andreote, Fernando Dini

    2014-03-01

    Mangrove soils are anaerobic environments rich in sulphate and organic matter. Although the sulphur cycle is one of the major actors in this ecosystem, little is known regarding the sulphur bacteria communities in mangrove soils. We investigated the abundance, composition and diversity of sulphur-oxidizing (SOB) and sulphate-reducing (SRB) bacteria in sediments from three Brazilian mangrove communities: two contaminated, one with oil (OilMgv) and one with urban waste and sludge (AntMgv), and one pristine (PrsMgv). The community structures were assessed using quantitative real-time polymerase chain reaction (qPCR), polymerase chain reaction-denaturing gradient gel electrophoresis (PCR-DGGE) and clone libraries, using genes for the enzymes adenosine-5'-phosphosulphate reductase (aprA) and sulphite reductase (Dsr) (dsrB). The abundance for qPCR showed the ratio dsrB/aprA to be variable among mangroves and higher according to the gradient observed for oil contamination in the OilMgv. The PCR-DGGE patterns analysed by Nonmetric Multidimensional Scaling revealed differences among the structures of the three mangrove communities. The clone libraries showed that Betaproteobacteria, Gammaproteobacteria and Deltaproteobacteria were the most abundant groups associated with sulphur cycling in mangrove sediments. We conclude that the microbial SOB and SRB communities in mangrove soils are different in each mangrove forest and that such microbial communities could possibly be used as a proxy for contamination in mangrove forests.

  1. Sulphur geochemistry and sapropel formation : syngenetic and diagenetic signals in eastern Mediterranean sediments

    NARCIS (Netherlands)

    Passier, Hilde Françoise

    1998-01-01

    In this thesis the sulphur geochemistry of eastern Mediterranean sediments is studied. The sediments discussed were recovered during the 1987 ABC cruise with R/V Tyro (core ABC27), the 1988 BAMO-3 expedition of R/V Bannock (cores GC17 and GC21), the 1991 Marflux cruise with R/V Marion Dufresne

  2. Adsorption of aromatic hydrocarbons and organic sulphur compounds by zeolite NaX

    Energy Technology Data Exchange (ETDEWEB)

    Fatkhi, A.; Eltekov, Yu.A.; Falkovich, M.I.; Gureev, A.A.; Solodovnikova, V.T.

    1981-01-01

    The article describes the equilibrium characteristics of the adsorption by zeolity NaX of several aromatic and organic sulphur compounds from isooctane solutions. The characteristics are necessary in studying the possible use of zeolite for the deep purification of hydrocarbons.

  3. Synthesis, Characterization and Biological activity of Some Novel Sulphur Bridged Pyrazoles

    Directory of Open Access Journals (Sweden)

    Singaravel Mohan,

    2010-10-01

    Full Text Available Mercaptoheterocyclic compounds on treatment with ethyl bromoacetate in the presence of base afforded thioacetate derivative of mercaptoheterocyclic compounds. These on subsequent treatment with hydrazine hydrate yielded acylated hydrazine derivative of ercaptoheterocyclic compounds. Reaction of these acylated hydrazinederivatives of mercaptoheterocyclic compounds with ketene dithioacetal derivative afforded sulphur bridged pyrazole derivatives.

  4. Formation and colloidal behaviour of elemental sulphur produced from the biological oxidation of hydrogensulphide.

    NARCIS (Netherlands)

    Janssen, A.J.H.

    1996-01-01

    The formation and aggregation of elemental sulphur from the microbiological oxidation of hydrogensulphide (H 2 S) by a mixed population of aerobic Thiobacillus -like bacteria has been investigated. Sulphide is formed during the anaerobic treatment of wastewaters whi

  5. Effect of elemental sulphur and compost on pH, electrical ...

    African Journals Online (AJOL)

    Effect of elemental sulphur and compost on pH, electrical conductivity and ... Suitable plant nutrition is one of the most important factors in the quantity and quality of crops' ... Soil water content was held close to field capacity and green house ...

  6. Natural occurrence of microbial sulphur oxidation by long-range electron transport in the seafloor

    NARCIS (Netherlands)

    Malkin, S.Y.; Rao, A.M.F.; Seitaj, D.; Vasquez-Cardenas, D.; Zetsche, E.-M.; Hidalgo-Martinez, S.; Boschker, H.T.S.; Meysman, F.J.R.

    2014-01-01

    Recently, a novel mode of sulphur oxidation was described in marine sediments, in which sulphide oxidation in deeper anoxic layers was electrically coupled to oxygen reduction at the sediment surface. Subsequent experimental evidence identified that long filamentous bacteria belonging to the family

  7. Sulphur-impregnated flow cathode to enable high-energy-density lithium flow batteries

    Science.gov (United States)

    Chen, Hongning; Zou, Qingli; Liang, Zhuojian; Liu, Hao; Li, Quan; Lu, Yi-Chun

    2015-01-01

    Redox flow batteries are promising technologies for large-scale electricity storage, but have been suffering from low energy density and low volumetric capacity. Here we report a flow cathode that exploits highly concentrated sulphur-impregnated carbon composite, to achieve a catholyte volumetric capacity 294 Ah l-1 with long cycle life (>100 cycles), high columbic efficiency (>90%, 100 cycles) and high energy efficiency (>80%, 100 cycles). The demonstrated catholyte volumetric capacity is five times higher than the all-vanadium flow batteries (60 Ah l-1) and 3-6 times higher than the demonstrated lithium-polysulphide approaches (50-117 Ah l-1). Pseudo-in situ impedance and microscopy characterizations reveal superior electrochemical and morphological reversibility of the sulphur redox reactions. Our approach of exploiting sulphur-impregnated carbon composite in the flow cathode creates effective interfaces between the insulating sulphur and conductive carbon-percolating network and offers a promising direction to develop high-energy-density flow batteries.

  8. Microbial carbon metabolism associated with electrogenic sulphur oxidation in coastal sediments

    NARCIS (Netherlands)

    Vasquez-Cardenas, Diana; van de Vossenberg, Jack; Polerecky, Lubos; Malkin, Sairah Y.; Schauer, Regina; Hidalgo-Martinez, Silvia; Confurius, Veronique; Middelburg, Jack J.; Meysman, Filip J R; Boschker, Henricus T S

    2015-01-01

    Recently, a novel electrogenic type of sulphur oxidation was documented in marine sediments, whereby filamentous cable bacteria (Desulfobulbaceae) are mediating electron transport over cm-scale distances. These cable bacteria are capable of developing an extensive network within days, implying a hig

  9. Polymerization of anthracene oil by thermal treatment in the presence of sulphur

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez, A.L.; Granda, M.; Bermejo, J.; Menendez, R. [Inst. Nacional del Carbon, Oviedo (Spain); Bernad, P. [Univ. de Oviedo (Spain). Dept. de Quimica Organometalica

    1997-12-31

    Anthracene oil was treated with sulphur in several concentrations, in the temperature range of 250-300 C, in order to promote polymerization of its components and produce pitch-like materials. Kinetics and possible mechanisms of the process were investigated. (orig.)

  10. Sulphur simulations for East Asia using the MATCH model with meteorological data from ECMWF

    Energy Technology Data Exchange (ETDEWEB)

    Engardt, Magnuz

    2000-03-01

    As part of a model intercomparison exercise, with participants from a number of Asian, European and American institutes, sulphur transport and conversion calculations were conducted over an East Asian domain for 2 different months in 1993. All participants used the same emission inventory and simulated concentration and deposition at a number of prescribed geographic locations. The participants were asked to run their respective model both with standard parameters, and with a set of given parameters, in order to examine the different behaviour of the models. The study included comparison with measured data and model-to-model intercomparisons, notably source-receptor relationships. We hereby describe the MATCH model, used in the study, and report some typical results. We find that although the standard and the prescribed set of model parameters differed significantly in terms of sulphur conversion and wet scavenging rate, the resulting change in atmospheric concentrations and surface depositions only change marginally. We show that it is often more critical to choose a representative gridbox value than selecting a parameter from the suite available. The modelled, near-surface, atmospheric concentration of sulphur in eastern China is typically 5- 10 {mu}g S m{sup -3}, with large areas exceeding 20 {mu}g S m{sup -3}. In southern Japan the values range from 2-5 {mu}g S m{sup -3} . Atmospheric SO{sub 2} dominates over sulphate near the emission regions while sulphate concentrations are higher over e.g. the western Pacific. The sulphur deposition exceeds several g sulphur m{sup -2} year{sup -1} in large areas of China. Southern Japan receives 03-1 g S m{sup -2} year{sup -1}. In January, the total wet deposition roughly equals the dry deposition, in May - when it rains more in the domain - total wet deposition is ca. 50% larger than total dry deposition.

  11. Amino acid composition of some Mexican foods.

    Science.gov (United States)

    Morales de León, Josefina; Camacho, M Elena; Bourges, Héctor

    2005-06-01

    Knowledge of the amino acid composition of foods is essential to calculate their chemical score, which is used to predict protein quality of foods and diets. Though amino acid composition of many foods is reasonably well established, better knowledge is needed on native foods consumed in different regions and countries. This paper presents the amino acid composition of different presentations of raw and processed foods produced and consumed in Mexico. The amino acid composition was determined using Beckman amino acid analyzers (models 116 and 6300). Tryptophan was determined using the Spies and Chambers method. Of the different foods analyzed, some comments are made on native or basic foods in Mexico: Spirulin, where lysine is the limiting amino acid, with a chemical score of 67%, is a good source of tryptophan (1.16g/16 gN); amaranth contains high levels of sulphur amino acids (4.09 to 5.34 g/16gN), with a protein content of 15 g/100g; and pulque, a Pre-Hispanic beverage that contains high levels of tryptophan (2.58 g/16 gN) and sulphur amino acids (2.72 g/16 gN). Finally, insects are good sources of sulphur amino acids and lysine.

  12. KINETICS OF DISSOLUTION OF PHOSPHORITE IN ACID MIXTURES

    African Journals Online (AJOL)

    The effect of hydrochloric acid on the dissolution of fluorapatite by sulphuric acid was studied at various H2SO_,_:HCl volume ratios ranging from 100 to 0 volume % of the ... Indeed only diffusion controlled processes are affected by the stirring speed [27]. ... surface area of the dissolving mineral [30], in this case fluorapatite.

  13. Pretreatment efficiency and structural characterization of rice straw by an integrated process of dilute-acid and steam explosion for bioethanol production.

    Science.gov (United States)

    Chen, Wen-Hua; Pen, Ben-Li; Yu, Ching-Tsung; Hwang, Wen-Song

    2011-02-01

    The combined pretreatment of rice straw using dilute-acid and steam explosion followed by enzymatic hydrolysis was investigated and compared with acid-catalyzed steam explosion pretreatment. In addition to measuring the chemical composition, including glucan, xylan and lignin content, changes in rice straw features after pretreatment were investigated in terms of the straw's physical properties. These properties included crystallinity, surface area, mean particle size and scanning electron microscopy imagery. The effect of acid concentration on the acid-catalyzed steam explosion was studied in a range between 1% and 15% acid at 180°C for 2 min. We also investigated the influence of the residence time of the steam explosion in the combined pretreatment and the optimum conditions for the dilute-acid hydrolysis step in order to develop an integrated process for the dilute-acid and steam explosion. The optimum operational conditions for the first dilute-acid hydrolysis step were determined to be 165°C for 2 min with 2% H(2)SO(4) and for the second steam explosion step was to be carried out at 180°C for 20 min; this gave the most favorable combination in terms of an integrated process. We found that rice straw pretreated by the dilute-acid/steam explosions had a higher xylose yield, a lower level of inhibitor in the hydrolysate and a greater degree of enzymatic hydrolysis; this resulted in a 1.5-fold increase in the overall sugar yield when compared to the acid-catalyzed steam explosion.

  14. Late Neoproterozoic to early Cambrian sulphur cycle-An isotopic investigation of sedimentary rocks from the Yangtze Platform

    Institute of Scientific and Technical Information of China (English)

    Tatiana GOLDBERG; Harald STRAUSS; GUO Qingjun; LIU Congqiang

    2003-01-01

    The sulphur cycle responds to changes in seawater chemistry, biological evolution and tectonic activity. We follow an isotopic approach in order to constrain the state of the ocean/atmosphere system during late Neoproterozoic and early Cambrian. For this purpose, a sedimentary succession deposited on the Yangtze Platform, South China, was analysed for its sulphur isotopic composition in different S-bearing phases. Redox changes were defined by the degree of pyritization (DOP) values in order to show variations in the oxygenation of the depositional environment. The sulphur isotopic composition of late Neoproterozoic to early Cambrian seawater sulphate ranges from +30‰ to +35‰ as evident from trace sulphate in unaltered carbonates and phosphorites. The isotopic composition for pyrite and organic sulphur varies between -16‰ and +23‰. The apparent sulphur isotopic fractionation between seawater sulphate and pyrite as well as organically bound sulphur varies between 7‰ and 50‰. This large fractionation, as well as its variability suggests a biological origin for pyrite and organically bound sulphur. The temporal evolution of different geochemical proxy signals is comparable for different successions across the Yangtze Platform.

  15. A Comparative Study on Corrosion Inhibition of Mild Steel Using Piper Nigrum L. in Different Acid Medium

    Directory of Open Access Journals (Sweden)

    B. Anand

    2010-01-01

    Full Text Available The inhibition of corrosion of mild steel using Piper nigrum L in different acid medium by weight loss method was investigated. The corrosion inhibition was studied in hydrochloric acid and sulphuric acid by weight loss method at different time interval at room temperature. The result showed that the corrosion inhibition efficiency of this compound was found to vary with different time interval and different acid concentration. Also, it was found that the corrosion inhibition behavior of Piper nigrum L is greater in sulphuric acid than hydrochloric acid. So, Piper nigrum L can be used as a good inhibitor for preventing mild steel material.

  16. Chemical and sulphur isotope compositions of pyrite in the Jaduguda U (-Cu-Fe) deposit, Singhbhum shear zone, eastern India: Implications for sulphide mineralization

    Science.gov (United States)

    Pal, Dipak C.; Sarkar, Surajit; Mishra, Biswajit; Sarangi, A. K.

    2011-06-01

    The Jaduguda U (-Cu-Fe) deposit in the Singhbhum shear zone has been the most productive uranium deposit in India. Pyrite occurs as disseminated grains or in sulphide stringers and veins in the ore zone. Veins, both concordant and discordant to the pervasive foliation, are mineralogically either simple comprising pyrite ± chalcopyrite or complex comprising pyrite + chalcopyrite + pentlandite + millerite. Nickel-sulphide minerals, though fairly common in concordant veins, are very rare in the discordant veins. Pyrite in Ni-sulphide association is commonly replaced by pentlandite at the grain boundary or along micro-cracks. Based on concentrations of Co and Ni, pyrite is classified as: type-A - high Co (up to 30800 ppm), no/low Ni; type-B - moderate Co (up to 16500 ppm) and moderate to high Ni (up to 32700 ppm); type-C - no/low Co and high Ni (up to 43000 ppm); type-D - neither Co nor Ni. Textural and compositional data of pyrites suggest that the hydrothermal fluid responsible for pre-/early-shearing mineralization evolved from Co-rich to Ni-rich and the late-/post-shearing fluid was largely depleted in minor elements. Sulphur isotope compositions of pyrite mostly furnish positive values ranging between -0.33 and 12.06‰. Composite samples of pyrites with only type-A compositions and mixed samples of type-A and type-B are consistently positive. However, pyrite with mixed type-A and type-C and pyrite with type-D compositions have negative values but close to 0‰. By integrating minor element and sulphur isotope compositions of pyrite in conjunction with other published data on the Jaduguda deposit, it is proposed that reduced sulphur for the precipitation of most pyrites (type-A, type-B) was likely derived from isotopically heavy modified seawater. However, some later sulphur might be magmatic in origin remobilized from existing sulphides in the mafic volcanic rocks in the shear zone.

  17. Chemical and sulphur isotope compositions of pyrite in the Jaduguda U (–Cu–Fe) deposit, Singhbhum shear zone, eastern India: Implications for sulphide mineralization

    Indian Academy of Sciences (India)

    Dipak C Pal; Surajit Sarkar; Biswajit Mishra; A K Sarangi

    2011-06-01

    The Jaduguda U (–Cu–Fe) deposit in the Singhbhum shear zone has been the most productive uranium deposit in India. Pyrite occurs as disseminated grains or in sulphide stringers and veins in the ore zone. Veins, both concordant and discordant to the pervasive foliation, are mineralogically either simple comprising pyrite ± chalcopyrite or complex comprising pyrite + chalcopyrite + pentlandite + millerite. Nickel-sulphide minerals, though fairly common in concordant veins, are very rare in the discordant veins. Pyrite in Ni-sulphide association is commonly replaced by pentlandite at the grain boundary or along micro-cracks. Based on concentrations of Co and Ni, pyrite is classified as: type-A — high Co (up to 30800 ppm), no/low Ni; type-B — moderate Co (up to 16500 ppm) and moderate to high Ni (up to 32700 ppm); type-C — no/low Co and high Ni (up to 43000 ppm); type-D — neither Co nor Ni. Textural and compositional data of pyrites suggest that the hydrothermal fluid responsible for pre-/early-shearing mineralization evolved from Co-rich to Ni-rich and the late-/post-shearing fluid was largely depleted in minor elements. Sulphur isotope compositions of pyrite mostly furnish positive values ranging between -0.33 and 12.06%. Composite samples of pyrites with only type-A compositions and mixed samples of type-A and type-B are consistently positive. However, pyrite with mixed type-A and type-C and pyrite with type-D compositions have negative values but close to 0. By integrating minor element and sulphur isotope compositions of pyrite in conjunction with other published data on the Jaduguda deposit, it is proposed that reduced sulphur for the precipitation of most pyrites (type-A, type-B) was likely derived from isotopically heavy modified seawater. However, some later sulphur might be magmatic in origin remobilized from existing sulphides in the mafic volcanic rocks in the shear zone.

  18. Energy optimization of integrated process plants

    Energy Technology Data Exchange (ETDEWEB)

    Sandvig Nielsen, J.

    1996-10-01

    A general approach for viewing the process synthesis as an evolutionary process is proposed. Each step is taken according to the present level of information and knowledge. This is formulated in a Process Synthesis Cycle. Initially the synthesis is conducted at a high abstraction level maximizing use of heuristics (prior experience, rules of thumbs etc). When further knowledge and information are available, heuristics will gradually be replaced by exact problem formulations. The principles in the Process Synthesis Cycle, is used to develop a general procedure for energy synthesis, based on available tools. The procedure is based on efficient use of process simulators with integrated Pinch capabilities (energy targeting). The proposed general procedure is tailored to three specific problems (Humid Air Turbine power plant synthesis, Nitric Acid process synthesis and Sulphuric Acid synthesis). Using the procedure reduces the problem dimension considerable and thus allows for faster evaluation of more alternatives. At more detailed level a new framework for the Heat Exchanger Network synthesis problem is proposed. The new framework is object oriented based on a general functional description of all elements potentially present in the heat exchanger network (streams, exchangers, pumps, furnaces etc.). (LN) 116 refs.

  19. Peracetic acid is a suitable disinfectant for recirculating fish-microalgae integrated multi-trophic aquaculture systems

    Directory of Open Access Journals (Sweden)

    Dibo Liu

    2016-11-01

    Full Text Available Integrated multi-trophic aquaculture (IMTA is a promising direction for the sustainable development of aquaculture. Microalgae have good potential to be integrated with recirculating aquaculture systems because they can use the nitrogen excreted from fish and share the same optimal pH value as in aquaculture. As a byproduct, the microalgae biomass can be used for fish feed or biofuel. However, the recirculating fish-microalgae IMTA system is under constant threat from fish pathogens and phytoplankton-lytic bacteria. Therefore, it is necessary to apply proper disinfectants as prophylaxis or treatment which are effective against these threats, but safe to fish and microalgae. For this purpose, peracetic acid (PAA is a valid option because it is highly effective against fish pathogens and bacteria at low concentrations and degrades spontaneously to harmless residues. In the present study, we exposed the culture of a marine microalgae Tetraselmis chuii once per day for four days to four PAA products with differing hydrogen peroxide (H2O2/PAA proportions at two concentrations (1 and 2 mg L−1 PAA. The H2O2 solutions at equivalent total peroxide (H2O2 + PAA concentrations were tested in parallel. The results show that the growth and photosynthesis of T. chuii were not affected by three of the PAA products (Wofasteril® E400, Wofasteril® E250 and Applichem® 150 and equivalent H2O2 solutions at both concentrations. In contrast, Wofasteril® Lspez and an equivalent H2O2 solution at both concentrations caused irreversible culture collapse, photosynthesis dysfunction and irreversible cell damage. In conclusion, PAA products with low proportions of H2O2 are optimal disinfectants for fish-microalgae IMTA systems.

  20. Vibrational spectroscopic and crystallographic study of the novel guanylurea salts with sulphuric and selenic acids

    Science.gov (United States)

    Matulková, I.; Fridrichová, M.; Císařová, I.; Vaněk, P.; Uhlík, F.; Němec, I.

    2017-03-01

    The family of known guanylurea(1+) sulphates was extended for two novel triclinic (space group P-1) members - bis(guanylurea(1+)) sulphate dihydrate and tetrakis(guanylurea(1+)) bis(hydrogen sulphate) sulphate. Additionally, the monoclinic (space group P21/n) guanylurea(1+) hydrogen selenate was also isolated and characterised. Besides of X-ray diffraction study these novel guanylurea chalcogenates were studied by the methods of vibrational spectroscopy. The study of thermal behaviour of the prepared salts revealed reversible λ-shaped anomaly for tetrakis(guanylurea(1+)) bis(hydrogen sulphate) sulphate at 354 K. This effect was studied in detail by the combination of DSC and temperature-dependent IR and Raman spectroscopies.