Municipal water pollution prevention program

International Nuclear Information System (INIS)

1991-03-01

EPA believes that the most effective and equitable means of assuring viability of this infrastructure is through environmentally preferred pollution prevention approaches especially through application of Municipal Water Pollution Prevention (MWPP). These approaches may enhance worker safety, improve the usability of sludge, increase the ability for local community expansion, and reduce operation and compliance costs. State-based municipal pollution prevention programs focus attention on a series of actions to prevent pollution in advance rather than taking more expensive corrective actions. MWPP encourages resource conservation to reduce water and energy use, appropriate pricing, toxicity reductions at the source, BOD reductions, recycling, proper treatment of wastes, and beneficial uses of sludge

Oxy-fuel combustion with integrated pollution control

Science.gov (United States)

Patrick, Brian R [Chicago, IL; Ochs, Thomas Lilburn [Albany, OR; Summers, Cathy Ann [Albany, OR; Oryshchyn, Danylo B [Philomath, OR; Turner, Paul Chandler [Independence, OR

2012-01-03

An oxygen fueled integrated pollutant removal and combustion system includes a combustion system and an integrated pollutant removal system. The combustion system includes a furnace having at least one burner that is configured to substantially prevent the introduction of air. An oxygen supply supplies oxygen at a predetermine purity greater than 21 percent and a carbon based fuel supply supplies a carbon based fuel. Oxygen and fuel are fed into the furnace in controlled proportion to each other and combustion is controlled to produce a flame temperature in excess of 3000 degrees F. and a flue gas stream containing CO2 and other gases. The flue gas stream is substantially void of non-fuel borne nitrogen containing combustion produced gaseous compounds. The integrated pollutant removal system includes at least one direct contact heat exchanger for bringing the flue gas into intimated contact with a cooling liquid to produce a pollutant-laden liquid stream and a stripped flue gas stream and at least one compressor for receiving and compressing the stripped flue gas stream.

Waste Minimization/Pollution Prevention Crosscut Plan, 1994

International Nuclear Information System (INIS)

1994-01-01

This plan establishes a Department-wide goal to reduce total releases of toxic chemicals to the environment and off-site transfers of such toxic chemicals by 50 percent by December 31, 1999, in compliance with Executive Order 12856. Each site that meets the threshold quantities of toxic chemicals established in the Emergency Planning and Community Right-to-Know Act (EPCRA) will participate in this goal. In addition, each DOE site will establish site-specific goals to reduce generation of hazardous, radioactive, radioactive mixed, and sanitary wastes and pollutants, as applicable. Implementation of this plan will represent a major step toward the environmental risks and costs associated with DOE operations and increasing the Department's use of preventive environmental management practices. Investing in Waste Minimization Pollution Prevention (WMin/PP) steadily reduce hazardous and radioactive waste generation and will reduce the need for waste management and unnecessary expenditures for waste treatment, storage, and disposal. A preventive approach to waste management will help solve current environmental and regulatory issues and reduce the need for costly future corrective actions. The purpose of this plan is to establish the strategic framework for integrating WMin/PP into all DOE internal activities. This program includes setting DOE policy and goals for reducing the generation of wastes and pollutants, increasing recycling activities, and establishing an infrastructure to achieve and measure the goals throughout the DOE complex. Waste Minimization and Pollution Prevention Awareness Plans, submitted to Headquarters by DOE field sites, will incorporate the WMin/PP activities and goals outlined in this plan. Success of the DOE WMin/PP program is dependent upon each field operation becoming accountable for resources used, wastes and pollutants generated, and wastes recycled

Grant Programs for Pollution Prevention

Science.gov (United States)

The Office of Pollution Prevention and Toxics is responsible for overseeing several grant programs for tribes and states which promote pollution prevention through source reduction and resource conservation.

Pollution prevention: The new environmental ethic

International Nuclear Information System (INIS)

Breen, J.J.; Dellarco, M.J.

1991-01-01

EPA is embarking on a new major environmental policy initiative: pollution prevention. It obviates the short-comings of end-of-pipe regulations and fosters efforts for industry to modify production practices to prevent pollution. For its part, the Agency has adopted this initiative in research and development, regulatory program development, and technology transfer activities. Research and Development programs are being established to address chemical substitution, reductions in chemical usage, product life cycles, and recycling. Regulatory programs are incorporating pollution prevention in major strategies of product stewardship and hazardous waste management. Technology transfer activities are designed to inform and educate industry and the public through Agency sponsored programs with the Pollution Prevention Information Center and the American Pollution Prevention Institute

Pollution prevention opportunity assessment: Foundation of pollution prevention for waste management

International Nuclear Information System (INIS)

Damewood, R.W.

1994-01-01

The objective of this paper is to promote the Pollution Prevention Opportunity Assessment (PPOA) technique as a fundamental of pollution prevention for waste management. All key elements of an effective PPOA program are presented. These key elements include impacts of environmental laws on pollution prevention, PPOA concepts and overview, waste minimization opportunities assessment, reporting and monitoring waste minimization progress, and PPOA program implementation. As environmental laws evolve the focus is shifting from end-of-pipe pollution control to front-end source reduction. Waste minimization was mistakenly interpreted to mean the reduction of hazardous waste after generation in the past. The Pollution Prevention Act of 1990 has clearly defined its requirement on resource reduction. Waste reduction can be viewed as a criterion to assess all industrial processes and operations. The fundamental approach of PPOA focuses on a mass balance concept. This concept deals with tracking of chemicals from the point of purchase, through storage, utilization in the process, and waste generation at the end of process. In other words, PPOA is a technique to analyze this input/output process. By applying PPOA techniques, the framework of applicable compliance requirements to the current operation process is established. Furthermore, documentation of PPOA itself can meet as documentation requirements for environmental compliance. In general, the PPOA process consists of two phases. The first phase involves input and output process description and waste characterization. The second phase is an opportunities assessment for waste minimization from input/output waste characterization. These two phases are explained in detail in the paper

The planned EC Directive on 'Integrated Pollution Prevention and Control' (IPC)

International Nuclear Information System (INIS)

Sellner, D.; Schnutenhaus, J.

1993-01-01

This EC Directive is intended to incorporate integrated pollution control as a mandatory obligation in the legal provisions governing industrial installations licensing within the EC. The article in hand presents an assessment of the Directive and discusses some possible impacts on the German national law in the field of pollution control, which hitherto has been defined on the basis of a preferably medium-oriented approach. A serious point of deviation from the German approach is seen in the fact that the draft's provisions relating to the licensing of industrial installations defines certain pre-conditions allowing a plant in a low-polluted area to be licensed, although the pollution control systems of the plant do not them come up to the state-of-the-art in pollution abatement technology. This is seen as a fact jeopardizing the principle of precantionary measures which has been firmly established in German pollution control law. (orig./HP) [de

Good Practice Guide Waste Minimization/Pollution Prevention; TOPICAL

International Nuclear Information System (INIS)

J Dorsey

1999-01-01

This Good Practice Guide provides tools, information, and examples for promoting the implementation of pollution prevention during the design phases of U.S. Department of Energy (DOE) projects. It is one of several Guides for implementing DOE Order 430.1, Life-cycle Asset Management. DOE Order 430.1 provides requirements for DOE, in partnership with its contractors, to plan, acquire, operate, maintain, and dispose of physical assets. The goals of designing for pollution prevention are to minimize raw material consumption, energy consumption, waste generation, health and safety impacts, and ecological degradation over the entire life of the facility (EPA 1993a). Users of this Guide will learn to translate national policy and regulatory requirements for pollution prevention into action at the project level. The Guide was written to be applicable to all DOE projects, regardless of project size or design phase. Users are expected to interpret the Guide for their individual project's circumstances, applying a graded approach so that the effort is consistent with the anticipated waste generation and resource consumption of the physical asset. This Guide employs a combination of pollution prevention opportunity assessment (PPOA) methods and design for environment (DfE) philosophies. The PPOA process was primarily developed for existing products, processes, and facilities. The PPOA process has been modified in this Guide to address the circumstances of the DOE design process as delineated in DOE Order 430.1 and its associated Good Practice Guides. This modified form of the PPOA is termed the Pollution Prevention Design Assessment (P2DA). Information on current nationwide methods and successes in designing for the environment also have been reviewed and are integrated into this guidance

Integration of biotechnology in remediation and pollution prevention activities

International Nuclear Information System (INIS)

Strong-Gunderson, J.M.

1996-01-01

The North American Free Trade Agreement/North American Agreement on Environmental Cooperation provides a mechanism for an international collaboration between the US, Canada, and Mexico to jointly develop, modify, or refine technologies that remediate or protect the environment. These countries have a vested interest in this type of collaboration because contaminants do not respect the boundaries of a manufacturing site, region, city, state, or country. The Environmental Sciences Division (ESD) at Oak Ridge National Laboratory (ORNL) consists of a diverse group of individuals who address a variety of environmental issues. ESD is involved in basic and applied research on the fate, transport, and remediation of contaminants; environmental assessment; environmental engineering; and demonstrations of advanced remediation technologies. The remediation and protection of the environment includes water, air, and soils for organic, inorganic, and radioactive contaminants. In addition to remediating contaminated sites, research also focuses on life-cycle analyses of industrial processes and the production of green technologies. The author focuses this discussion on subsurface remediation and pollution prevention; however, the research activities encompass water, soil and air and many of the technologies are applicable to all environments. The discussion focuses on the integration of biotechnology with remediation activities and subsequently linking these biological processes to other remediation technologies

The History of Petroleum Pollution in Malaysia; Urgent Need for Integrated Prevention Approach

OpenAIRE

Mahyar Sakari

2010-01-01

Petroleum pollution is known as point and non-point source of contaminations in the environment. A major class of petroleum contaminant is groups of compounds consist of two or more fused benzene rings called polycyclic aromatic hydrocarbons (PAHs) that are carcinogenic, mutagenic and toxic. Source identification of petroleum pollution is necessary to prevent pollution entry into the environment. Eight sedimentary cores were obtained from developed and developing areas around Peninsular Malay...

The History of Petroleum Pollution in Malaysia; Urgent Need for Integrated Prevention Approach

Directory of Open Access Journals (Sweden)

Mahyar Sakari

2010-01-01

Full Text Available Petroleum pollution is known as point and non-point source of contaminations in the environment. A major class of petroleum contaminant is groups of compounds consist of two or more fused benzene rings called polycyclic aromatic hydrocarbons (PAHs that are carcinogenic, mutagenic and toxic. Source identification of petroleum pollution is necessary to prevent pollution entry into the environment. Eight sedimentary cores were obtained from developed and developing areas around Peninsular Malaysia to investigate the historical profile of PAHs, their characteristics and its possible origins. The results showed that the PAHs concentrations varied from very minimum to 2400 ng/g d. w. in average quarter century intervals. Most of the studied locations showed high contribution of PAHs from combusted fuel, coal, biomasses and wood materials except for the southern part of Peninsular Malaysia in which revealed dominance of petroleum products. The findings indicate that PAHs are delivered from different intermediate materials such as asphalt, street dust, vehicular emission and crankcase oil. However, there has been a decline of PAHs input into the marine environment in recent years; petroleum is shown to be a significant cause of marine pollution since the second quarter of 20th century. An overview on sourced materials of petroleum pollution indicates multi-approach necessity toward pollution control, regardless of concentration and possible degradation processes. Various sectors both governmental and non-governmental are needed for prevention and control of petroleum pollution where different sources apparently contribute to the pollution generation process.

Industrial pollution prevention handbook

International Nuclear Information System (INIS)

Freeman, H.M.

1995-01-01

This book presents the techniques, technologies, regulations, and strategies that define pollution prevention. The subject is addressed from many perspectives by prominent experts. In many ways pollution prevention, rather than being a specialty field itself, is actually a convergence of fields drawing upon knowledge in a wide variety of more typical fields of expertise. Individual chapters have been processed separately for inclusion in the appropriate data bases

Environmental Pollution Prevention, Control and Abatement

Science.gov (United States)

1977-08-30

AD-A271 117 fDATE August 30. 1977 ASD (ORA&L) Department of Defense Instruction SUBJECT: Environmental Pollution Prevention, Control and Abatement...Ensure that any funds appropriated and apportioned for the prevention, control, and abatement of environmental pollution are not used for any other...77 References (a) Executive Order 11752, "Prevention, Control, and Abatement of Environmental Pollution at Federal Facilities," December 19, 1973 (b

Executive summary, Hanford Site Pollution Prevention Plan

International Nuclear Information System (INIS)

1992-08-01

A pollution prevention plan is an organized, comprehensive, and continual effort to systematically reduce waste generation. The Hanford Site Pollution Prevention Plan is designed to eliminate or minimize pollutant releases to all environmental media from all aspects of Site operations. These efforts offer increased protection of public health and the environment. This plan reflects the goals and policies for pollution prevention at the Hanford Site and represents an ongoing effort to make pollution prevention part of the Site operating philosophy. The plan encompasses hazardous waste only and excludes radioactive waste and radioactive mixed waste

Pollution prevention constraints within DOE facilities

International Nuclear Information System (INIS)

Walzer, A.E.

1992-01-01

The signing of the Pollution Prevention Act of 1990, has marked a new environmental era. The 1990s environmental movement is shifting from ''end of the pipe'' treatment towards a philosophy of source reduction (predicated by the Pollution Prevention Act), where engineering solutions and materials substitution are sought to reduce the volume and toxicity of waste. This change comes after 20 years of treatment legislation, where in many cases the location or media in which our pollution is deposited was merely changed. This problem is exemplified by the enormous environmental problems created by waste sites. Our inability to deal with the substantial waste generated has produced the environmental legacy on the Department of Energy (DOE) sites, a legacy that will cost billions of dollars to remediate. How then do we solve our waste problems and avoid future legacies? This paper outlines some of the obstacles to pollution prevention within the DOE system and explores opportunities to remove these barriers. Industry, whose foundation is economics, has found it attractive to reduce their wastes, particularly in the wake of escalating waste disposal costs. However, within federal facilities where basic economic principles do not prevail, incentives towards pollution prevention need to be evaluated. Our current system of segregated DOE programs creates obstacles for waste generators to work productively with other programs. Certain policies and practices also limit the generators' responsibility and costs for their waste, which is counter productive to waste minimization and pollution prevention. To meet new environmental challenges and to be proactive in pollution prevention we must evaluate our systems and remove barriers that impede progress toward pollution prevention

Pollution prevention and energy conservation: Understanding the interactions

International Nuclear Information System (INIS)

Purcell, A.H.

1992-01-01

The traditional view holds that pollution prevention is good for energy conservation and vice versa. Analysis of pollution prevention and energy conservation activities indicates, however, that interactions and synergies between environmental and energy factors can mean that pollution prevention can be energy intensive and, conversely, that energy conservation can lead to increased pollution. Full cost accounting, taking into account all media, must be performed before precise pollution prevention-energy conservation interrelationships can be characterized and quantified. Use of a pollution prevention-energy conservation matrix can further this understanding

Orientation to pollution prevention for facility design

Energy Technology Data Exchange (ETDEWEB)

Raney, E.A.; Whitehead, J.K.; Encke, D.B. [Westinghouse Hanford Co., Richland, WA (United States); Dorsey, J.A. [Kaiser Engineers Hanford Co., Richland, WA (United States)

1994-01-01

This material was developed to assist engineers in incorporating pollution prevention into the design of new or modified facilities within the U.S. Department of Energy (DOE). The material demonstrates how the design of a facility can affect the generation of waste throughout a facility`s entire life and it offers guidance on how to prevent the generation of waste during design. Contents include: Orientation to pollution prevention for facility design training course booklet; Pollution prevention design guideline; Orientation to pollution prevention for facility design lesson plan; Training participant survey and pretest; and Training facilitator`s guide and schedule.

46 CFR 189.25-38 - Pollution prevention.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Pollution prevention. 189.25-38 Section 189.25-38... AND CERTIFICATION Inspection for Certification § 189.25-38 Pollution prevention. At each inspection... meets the vessel design and equipment requirements for pollution prevention in 33 CFR part 155, subpart...

Turbo-gas emissions and integrated pollution prevention and control (IPPC)

International Nuclear Information System (INIS)

Mariani, M.; Sera, B.

2005-01-01

The present paper considers the gas-turbine pollution and joints out that the NO, is the most important pollutant among others pollutants as well as the carbon oxide and the volatile organic compounds because the NO x , has a high mass production rate (in the combustion chamber), elevated toxicity to the ecosystem and because of being in the atmosphere a precursor of secondary ultrafine particles PM 2,5 . In with reference to the integrated pollution and control (IPPC) the job shows schemes of chain chemical reactions which are on the base of the formation of different types of NO x , thermal and organic, and it illustrates the influence of some operative parameters on the combustion's efficiency and then on the NO x , production rate. Also, the study gives the best absolvable techniques (BAT) to reduce the NO x , production rate and to demolish it before its introduction, as well as gas exhaust, in the atmosphere. At the end, the work shows that the gas-turbine are to consider thermal engines with a little environment impact index specially when they make use of the natural gas, as well as fuel [it

Contacts in the Office of Pesticide Programs, Biopesticides and Pollution Prevention Division

Science.gov (United States)

Contact the Biopesticides and Pollution Prevention Division (BPPD) about regulatory activities associated with biologically-based pesticides, implementation of integrated pest management and the Pesticide Environmental Stewardship Program.

46 CFR 91.25-38 - Pollution prevention.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Pollution prevention. 91.25-38 Section 91.25-38 Shipping... CERTIFICATION Inspection for Certification § 91.25-38 Pollution prevention. At each inspection for certification... design and equipment requirements for pollution prevention in 33 CFR part 155, subpart B. [CGD 71-161R...

46 CFR 71.25-37 - Pollution prevention.

Science.gov (United States)

2010-10-01

... 46 Shipping 3 2010-10-01 2010-10-01 false Pollution prevention. 71.25-37 Section 71.25-37 Shipping... Annual Inspection § 71.25-37 Pollution prevention. At each inspection for certification, the inspector... pollution prevention in 33 CFR part 155, subpart B. [CGD 71-161R, 37 FR 28262, Dec. 21, 1972] ...

Integrated environmental assessment and pollution prevention in Vietnam: the case of anthracite production

Energy Technology Data Exchange (ETDEWEB)

Chinh, L.D.; Gheewala, S.H.; Bonnet, S. [King Mongkuts University of Technology at Thonburi, Bangkok (Thailand)

2007-07-01

Abstract: Using the concept of life cycle analysis, the whole life cycle of anthracite production in Vietnam was assessed and the environmental 'hot-spots' were identified. These include (I) dust pollution at coal transfer points or piles in storage; (ii) noise pollution resulting from the usage of heavy equipment, and (iii) high volume of acid and turbid mine water discharged into the environment. Pollution prevention and treatment options were identified and discussed in this study which consists of wet treatment of dust, planning, collection and treatment of mine water, planting of trees for dust and noise reduction as well as minimization of erosion. Some recommendations are made for pollution abatement from coal production and improvement of anthracite production in the region.

Pollution prevention program implementation plan

International Nuclear Information System (INIS)

Engel, J.A.

1996-09-01

The Pollution Prevention Program Implementation Plan (the Plan) describes the Pacific Northwest National Laboratory's (PNNL) Pollution Prevention (P2) Program. The Plan also shows how the P2 Program at PNNL will be in support of and in compliance with the Hanford Site Waste Minimization and Pollution Prevention (WMin/P2) Awareness Program Plan and the Hanford Site Guide for Preparing and Maintaining Generator Group Pollution Prevention Program Documentation. In addition, this plan describes how PNNL will demonstrate compliance with various legal and policy requirements for P2. This plan documents the strategy for implementing the PNNL P2 Program. The scope of the P2 Program includes implementing and helping to implement P2 activities at PNNL. These activities will be implemented according to the Environmental Protection Agency's (EPA) hierarchy of source reduction, recycling, treatment, and disposal. The PNNL P2 Program covers all wastes generated at the Laboratory. These include hazardous waste, low-level radioactive waste, radioactive mixed waste, radioactive liquid waste system waste, polychlorinated biphenyl waste, transuranic waste, and sanitary waste generated by activities at PNNL. Materials, resource, and energy conservation are also within the scope of the PNNL P2 Program

Annotated Bibliography of Law-Related Pollution Prevention Sources.

Science.gov (United States)

Lynch, Holly; Murphy, Elaine

This annotated bibliography of law-related pollution prevention sources was prepared by the National Pollution Prevention Center for Higher Education. Some topics of the items include waste reduction, hazardous wastes, risk reduction, environmental policy, pollution prevention, environmental protection, environmental leadership, environmental…

DOE's Pollution Prevention Information Clearinghouse (EPIC)

International Nuclear Information System (INIS)

Otis, P.T.

1994-05-01

The US Department of Energy's (DOE's) Pollution Prevention Information Clearinghouse (EPIC) is a computer system intended for the exchange of pollution prevention information DOE-wide. EPIC is being developed as a distributed system that will allow access to other databases and applications. The first prototype of EPIC (Prototype I) was put on-line in January 1994. Prototype I contains information on EM-funded pollution prevention projects; relevant laws, regulations, guidance, and policy; facility and DOE contacts; and meetings and conferences. Prototype I also gives users access to the INEL Hazardous Solvent Substitution Data System (HSSDS) and to information contained on the US Environmental Protection Agency's (EPNS) Pollution Prevention Infbrmation Exchange System (PIES) as a test of the distributed system concept. An initial user group of about 35 is testing and providing feedback on Prototype I. Prototype II, with a Graphical User Interface (GUI), is planned for the end of CY94. This paper describes the current state of EPIC in terms of architecture, user interface, and information content. Plans for Prototype II and the final system are then discussed. The EPIC development effort is being coordinated with EPA and US Department of Defense (DoD) efforts to develop or upgrade their pollution prevention information exchange systems

An investigation of air emission levels from distinct iron and steel production processes with the adoption of pollution control and pollution prevention alternatives

International Nuclear Information System (INIS)

Costa, M.M.; Schaeffer, R.

1999-01-01

This paper aims to investigate environmental aspects from different iron and steel production processes. A methodology based on material flows is developed in order to verify some air emission levels attained by Pollution Control and Pollution Prevention alternatives. The data basis for modeling energy and materials flows in iron and steel production is obtained from a literature review on different technological processes, energy and materials consumption and pollutant releases to the environmental Modeling combines both process analysis and input-output techniques to simulate the different iron and steel production routes and to estimate the resulting total atmospheric pollution releases based on air emission factors for several pollutants by each production step. Processes examined include: (1) Conventional Integrated (100% ore-based and partly scrap-based); (2) Mini-mill with EAF (100% scrap-based and partly DRI-based); and (3) New Integrated based on the COREX smelting reduction process. Among the alternatives considered for air emissions reductions are those related to Pollution Control (mainly gas cleaning systems) and to Pollution Prevention (change/reduction in input materials, operational procedures and housekeeping improvements, on-site recycling and technology innovations and modifications). Results indicate higher air pollution intensity for the Conventional Integrated Route over the Mini-mill with EAF and COREX smelting reduction processes, though pointing out that final figures are strongly affected by the systems' boundaries and the different air emission levels of each production step

Fiscal Year 2015 Pollution Prevention Grant Summaries

Science.gov (United States)

The Office of Pollution Prevention and Toxics is responsible for overseeing several grant programs for tribes and states which promote pollution prevention through source reduction and resource conservation.

Fiscal Year 2014 Pollution Prevention Grant Summaries

Science.gov (United States)

The Office of Pollution Prevention and Toxics is responsible for overseeing several grant programs for tribes and states which promote pollution prevention through source reduction and resource conservation.

Application of environmental accounting to pollution prevention assessments

International Nuclear Information System (INIS)

Del Mar, R.A.

1997-08-01

Environmental accounting represents a major paradigm shift in the way most companies account for costs and benefits. However, it is a change that must be made if pollution prevention is to become institutionalized into the corporate and government mainstream. Pollution prevention investments must be justified on an economic basis; without environmental accounting tools, pollution prevention investments cannot show their true profitability. This is because traditional accounting methods only track billable costs, thus ignoring some of the major benefits of pollution prevention investments, which are indirect savings resulting from a lessening of a company's regulatory compliance burden and present and future liabilities. This paper discusses how to apply environmental accounting principles to pollution prevention assessments to improve the outcome of profitability analyses

Guide to Pollution Prevention in Your Community.

Science.gov (United States)

Luppino, Tony; Gilbert, Reg

The purpose of this guide is to help citizen advocates create and improve the environmental practices of industry and government in the Great Lakes Basin. The practices advocated focus on pollution prevention instead of relying solely on pollution control. An introduction examines the larger issues of pollution prevention and zero discharge as the…

Pollution prevention and air quality

International Nuclear Information System (INIS)

Fuentes Hector; Tsihrintzis Vassilios

1997-01-01

Pollution prevention (P2) results from the combined effect of the public opinion, a new environmental value system, government regulation, but above all, the search for an economic development within the context of environmental protection. The reasons for prevention are fundamental: profit from a new economic frontier; reduced potential for civil and criminal liability; and the effective and economic protection of the environment. This paper addresses, among other relevant issues, the following topics: justification and objective of pollution prevention; strategy and methodology for its implementation; examples of successes and tools; benefits and barriers and some recommendation

76 FR 64245 - Oil Pollution Prevention; Spill Prevention, Control, and Countermeasure (SPCC) Rule-Compliance...

Science.gov (United States)

2011-10-18

... Oil Pollution Prevention; Spill Prevention, Control, and Countermeasure (SPCC) Rule--Compliance Date... burden to comply with the regulations contained in 40 CFR part 112--Oil Pollution Prevention. However, in... rule will be effective November 7, 2011. List of Subjects in 40 CFR Part 112 Oil pollution prevention...

76 FR 72120 - Oil Pollution Prevention; Spill Prevention, Control, and Countermeasure (SPCC) Rule-Compliance...

Science.gov (United States)

2011-11-22

... Oil Pollution Prevention; Spill Prevention, Control, and Countermeasure (SPCC) Rule--Compliance Date... rule will be effective November 22, 2011. List of Subjects in 40 CFR Part 112 Oil pollution prevention... Regulations is amended as follows: PART 112--OIL POLLUTION PREVENTION 0 1. The authority citation for part 112...

Hanford Site waste minimization and pollution prevention awareness program plan

International Nuclear Information System (INIS)

Place, B.G.

1998-01-01

This plan, which is required by US Department of Energy (DOE) Order 5400. 1, provides waste minimization and pollution prevention guidance for all Hanford Site contractors. The plan is primary in a hierarchical series that includes the Hanford Site Waste Minimization and Pollution Prevention Awareness Program Plan, Prime contractor implementation plans, and the Hanford Site Guide for Preparing and Maintaining Generator Group Pollution Prevention Program Documentation (DOE-RL, 1997a) describing programs required by Resource Conservation and Recovery Act of 1976 (RCRA) 3002(b) and 3005(h) (RCRA and EPA, 1994). Items discussed include the pollution prevention policy and regulatory background, organizational structure, the major objectives and goals of Hanford Site's pollution prevention program, and an itemized description of the Hanford Site pollution prevention program. The document also includes US Department of Energy, Richland Operations Office's (RL's) statement of policy on pollution prevention as well as a listing of regulatory drivers that require a pollution prevention program

Preventing pollution from plutonium processing

International Nuclear Information System (INIS)

Pillay, K.K.S.

1993-01-01

The plutonium processing facility at Los Alamos has adopted the strategic goal of becoming a facility that processes plutonium in a way that produces only environmentally benign waste streams. Pollution prevention through source reduction and environmentally sound recycling are being pursued. General approaches to waste reductions are administrative controls, modification of process technologies, and additional waste polishing. Recycling of waste materials, such as spent acids and salts, are technical possibilities and are being pursued to accomplish additional waste reduction. Liquid waste stream polishing to remove final traces of plutonium and hazardous chemical constituents is accomplished through (a) process modifications, (b) use of alternative chemicals and sorbents for residue removal, (c) acid recycling, and (d) judicious use of a variety of waste polishing technologies. Technologies that show promise in waste minimization and pollution prevention are identified. Working toward this goal of pollution prevention is a worthwhile endeavor, not only for Los Alamos, but for the Nuclear Complex of the future

Preventing pollution from plutonium processing

International Nuclear Information System (INIS)

Pillay, K.K.S.

1995-01-01

The plutonium processing facility at Los Alamos has adopted the strategic goal of becoming a facility that processes plutonium in a way that produces only environmentally benign waste streams. Pollution prevention through source reduction and environmentally sound recycling are being pursued. General approaches to waste reductions are administrative controls, modification of process technologies, and additional waste polishing. Recycling of waste materials, such as spent acids and salts, are technical possibilities and are being pursued to accomplish additional waste reduction. Liquid waste stream polishing to remove final traces of plutonium and hazardous chemical constituents is accomplished through process modifications, use of alternative chemicals and sorbents for residue removal, acid recycling, and judicious use of a variety of waste polishing technologies. Technologies that show promise in waste minimization and pollution prevention are identified. Working toward this goal of pollution prevention is a worthwhile endeavor , not only for Los Alamos, but for the Nuclear Complex of the future. (author) 12 refs.; 2 figs

Information resources for US Department of Energy pollution prevention programs

Energy Technology Data Exchange (ETDEWEB)

Peterson, K.L.; Snowden-Swan, L.J.; Butner, R.S.

1994-01-01

In support of the US Department of Energy`s (DOE`s) pollution prevention efforts being conducted under the aegis of DOE`s Office of Environmental Restoration and Waste Management (EM) program, Pacific Northwest Laboratory was tasked with evaluating pollution prevention information resources. The goal of this activity was to improve the effectiveness of DOE`s pollution prevention activities through improved information flow, both within the complex, and more specifically, between DOE and other organizations that share similar pollution prevention challenges. This report presents our findings with respect to the role of information collection and dissemination within the complex, opportunities for teaming from successes of the private sector, and specific information needs of the DOE pollution prevention community. These findings were derived from a series of interviews with pollution prevention coordinators from across the DOE complex, review of DOE site and facility pollution prevention plans, and workshops with DOE information users as well as an information resources workshop that brought together information specialists from private industry, non-profit organizations, as well as state and regional pollution prevention assistance programs.

Pollution Prevention Information Network (PPIN) Grant Summaries 2014

Science.gov (United States)

The Office of Pollution Prevention and Toxics is responsible for overseeing several grant programs for tribes and states which promote pollution prevention through source reduction and resource conservation.

Pollution Prevention in Air Force System Acquisition Programs

Science.gov (United States)

1994-09-01

noise requirements, handling radioactive materials, etc. The values should 278 be expressed in terms of indicators that, either quantitatively or...Structure pollhtion prevention ana~lysis Polution Prevention Analysis (PPA)? NEPA w/pollution prevention information - pollution Change prevention...Accumulation Procedures PS 81,04 Waste Jet Fuel Handling and Disposal Safe Practice Instructions (SPI) SPI 104 Radioactive Waste SPI 206 Mercury

Pollution prevention opportunity assessments, a training and resource guide

Energy Technology Data Exchange (ETDEWEB)

VALERO, O.J.

1998-11-03

The intention of the ''Pollution Prevention Opportunity Assessment Training and Resource Guide'' is to help Hanford waste generators identify ways to reduce waste through the Pollution Prevention Opportunity Assessment (P20A) process. This document presents pollution prevention tools and provides a step-by-step approach for conducting assessments.

B Plant Complex pollution prevention plan. Revision 1

International Nuclear Information System (INIS)

Beam, T.G.

1994-01-01

The US Department of Energy (DOE) has directed Westinghouse Hanford Company (WHC) to develop an effective strategy to minimize the generation of hazardous, radioactive, and mixed wastes at Hanford in compliance with state and federal regulations. WHC has formalized a pollution prevention program composed of management policies, management requirements and procedures. This plan addresses pollution prevention for B Plant Complex. A pollution prevention team is in place and has been assigned responsibility for implementing the plan. This plan includes actions and goals for reducing volume and toxicity of waste generated, as well as a basis for evaluation of progress. Descriptions of waste streams, current specific goals, general pollution prevention methods, and specific accomplishments are in the appendices of this plan

75 FR 45572 - Oil Pollution Prevention; Spill Prevention, Control, and Countermeasure (SPCC) Rule-Proposed...

Science.gov (United States)

2010-08-03

... Oil Pollution Prevention; Spill Prevention, Control, and Countermeasure (SPCC) Rule--Proposed... Federal Regulations is proposed to be amended as follows: PART 112--OIL POLLUTION PREVENTION 1. The... certain facilities must prepare or amend their Spill Prevention, Control, and Countermeasure (SPCC) Plans...

Pollution prevention initiatives at US EPA: 'Green Lights'

International Nuclear Information System (INIS)

Lawson, J.; Kwartin, R.

1991-01-01

US EPA is initiating a pollution prevention approach to supplement its historic command-control, regulatory approach to environmental protection. EPA believes polllution prevention, where applicable and possible, represents a quicker, less expensive and even profitable strategy for environmental protection. Most clearly, energy-efficiency provides an opportunity to prevent significant amounts of pollution related to the inefficeint generation and use of electricity. EPA's first energy productivity and pollution prevention program is Green Lights. Beyond its own merits, Green Lights will also provide important experience to EPA as it develops its Green Machines program to accelerate the market for efficient appliances and equipment

46 CFR 131.935 - Prevention of oil pollution.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Prevention of oil pollution. 131.935 Section 131.935... Miscellaneous § 131.935 Prevention of oil pollution. Each vessel must be operated in compliance with— (a) Section 311 of the Federal Water Pollution Control Act, as amended (33 U.S.C. 1321); and (b) 33 CFR parts...

Pollution prevention in the petroleum refining industry - bibliography

International Nuclear Information System (INIS)

Fournier, M.

1995-03-01

The Great Lakes Pollution Prevention Centre has compiled a list of references to assist the petroleum refining industry in adopting pollution prevention as an important environmental management strategy. Items included were divided into 14 categories of pollution types, such as air emissions, alternative fuels, chemical substitution, grounds keeping, leaks and spills, paints, waste management plan and others

76 FR 64296 - Oil Pollution Prevention; Spill Prevention, Control, and Countermeasure (SPCC) Rule-Compliance...

Science.gov (United States)

2011-10-18

... Oil Pollution Prevention; Spill Prevention, Control, and Countermeasure (SPCC) Rule--Compliance Date... Federal Register. List of Subjects in 40 CFR Part 112 Oil pollution prevention, Farms, Compliance date... proposing to amend the date by which farms must prepare or amend, and implement their Spill Prevention...

Pressures on industry to move to pollution prevention

International Nuclear Information System (INIS)

Poiasek, R.B.

1991-01-01

In a recent EPA report entitled Reducing Risk: Sorting Priorities and Strategies for Environmental Protection, a recommendation was made that EPA should emphasize pollution prevention as the preferred option for reducing risk. A significant number of states have adopted legislation requiring industry to conduct pollution prevention planning activities and submit reports to the state agencies. Federal legislation may be on the way. Industrial trade organizations are looking at the Chemical Manufacturing Association's Responsible Care: Program. Institutional investment groups are looking at initiatives like the Valdez Principles when selecting its portfolio, each of these initiatives have pollution prevention components. Environmentalists are demanding further attention be paid to pollution prevention. Industry is responding with a variety of programs designed to move them away from the classic end-of-the pipe controls which EPA mandated in previous regulations

Waste Minimization and Pollution Prevention Awareness Plan

International Nuclear Information System (INIS)

1992-01-01

The purpose of this plan is to document the Lawrence Livermore National Laboratory (LLNL) Waste Minimization and Pollution Prevention Awareness Program. The plan specifies those activities and methods that are or will be employed to reduce the quantity and toxicity of wastes generated at the site. It is intended to satisfy Department of Energy (DOE) and other legal requirements that are discussed in Section C, below. The Pollution Prevention Awareness Program is included with the Waste Minimization Program as suggested by DOE Order 5400.1. The intent of this plan is to respond to and comply with the Department's policy and guidelines concerning the need for pollution prevention. The Plan is composed of a LLNL Waste Minimization and Pollution Prevention Awareness Program Plan and, as attachments, Directorate-, Program- and Department-specific waste minimization plans. This format reflects the fact that waste minimization is considered a line management responsibility and is to be addressed by each of the Directorates, Programs and Departments. Several Directorates have been reorganized, necessitating changes in the Directorate plans that were published in 1991

Environmental Restoration Contractor Waste Minimization and Pollution Prevention Plan

International Nuclear Information System (INIS)

Lewis, R.A.

1994-11-01

The purpose of this plan is to establish the Environmental Restoration Contractor (ERC) Waste Minimization and Pollution Prevention (WMin/P2) Program and outline the activities and schedules that will be employed to reduce the quantity and toxicity of wastes generated as a result of restoration and remediation activities. It is intended to satisfy the US Department of Energy (DOE) and other legal requirements. As such, the Pollution Prevention Awareness program required by DOE Order 5400.1 is included with the Pollution Prevention Program. This plan is also intended to aid projects in meeting and documenting compliance with the various requirements for WMin/P2, and contains the policy, objectives, strategy, and support activities of the WMin/P2 program. The basic elements of the plan are pollution prevention goals, waste assessments of major waste streams, implementation of feasible waste minimization opportunities, and a process for reporting achievements. Various pollution prevention techniques will be implemented with the support of employee training and awareness programs to reduce waste and still meet applicable requirements. Information about the Hanford Site is in the Hanford Site Waste Minimization and Pollution Prevention Awareness Program Plan

Air pollution: impact and prevention.

Science.gov (United States)

Sierra-Vargas, Martha Patricia; Teran, Luis M

2012-10-01

Air pollution is becoming a major health problem that affects millions of people worldwide. In support of this observation, the World Health Organization estimates that every year, 2.4 million people die because of the effects of air pollution on health. Mitigation strategies such as changes in diesel engine technology could result in fewer premature mortalities, as suggested by the US Environmental Protection Agency. This review: (i) discusses the impact of air pollution on respiratory disease; (ii) provides evidence that reducing air pollution may have a positive impact on the prevention of disease; and (iii) demonstrates the impact concerted polices may have on population health when governments take actions to reduce air pollution. © 2012 The Authors. Respirology © 2012 Asian Pacific Society of Respirology.

Air pollution prevention at the Hanford Site: Status and recommendations

International Nuclear Information System (INIS)

Engel, J.A.

1995-08-01

With the introduction of the Clean Air Act Amendments of 1990 and other air and pollution prevention regulations, there has been increased focus on both pollution prevention and air emissions at US DOE sites. The Pollution Prevention (P2) Group of WHC reviewed the status of air pollution prevention with the goal of making recommendations on how to address air emissions at Hanford through pollution prevention. Using the air emissions inventory from Hanford's Title V permit, the P2 Group was able to identify major and significant air sources. By reviewing the literature and benchmarking two other DOE Sites, two major activities were recommended to reduce air pollution and reduce costs at the Hanford Site. First, a pollution prevention opportunity assessment (P2OA) should be conducted on the significant painting sources in the Maintenance group and credit should be taken for reducing the burning of tumbleweeds, another significant source of air pollution. Since they are significant sources, reducing these emissions will reduce air emission fees, as well as have the potential to reduce material and labor costs, and increase worker safety. Second, a P2OA should be conducted on alternatives to the three coal-fired powerhouses (steam plants) on-site, including a significant costs analysis of alternatives. This analysis could be of significant value to other DOE sites. Overall, these two activities would reduce pollution, ease regulatory requirements and fees, save money, and help Hanford take a leadership role in air pollution prevention

Integrated pollution prevention and control for heavy ceramic industry in Galicia (NW Spain).

Science.gov (United States)

Barros, M C; Bello, P; Roca, E; Casares, J J

2007-03-22

The heavy ceramic industry (building materials and refractory products manufacture) is an important source of pollutants to the environment. For this reason these industrial sub-sectors are included in prevention and control pollution policies, specifically those of the European Union. The IPPC Directive pays particular attention to the mineral industries, not least to the ceramic industry (epigraph 3.5, Annex I). In this paper, a methodology which is being applied to support IPPC installations and the competent administrative authority in Galicia (NW Spain) is presented. For that, the Galician heavy ceramic industry is analysed, as also are the ways to study the Best Available Techniques (BAT) with a view to establishing the emission limit values (ELV) for each specific case. Hence, a technological state of the art has been carried out for both sub-sectors, from the point of view of implementation of the IPPC in Galicia. Following this, the processes are described briefly and an analysis of the consumption and emission levels of the main pollutants is made. An inventory that includes the best environmental practices and the preventive and abatement candidate techniques as BAT was elaborated for both considered sub-sectors. An information data sheet for each candidate BAT is presented as a method to help both the industries and the competent authority to identify a candidate technique of the inventory as BAT. Three illustrative examples of the application of this procedure are presented for different emissions to environmental media for Galician installations.

Local government`s pollution prevention program

Energy Technology Data Exchange (ETDEWEB)

Swanson, D. [Boulder Country Pollution Prevention Program, Boulder, CO (United States)

1996-12-31

The pollution prevention program operated by the Health Department of Boulder County is called Business Partners for a Clean Environment (Business Partners). It is a cooperative effort among local businesses, the City of Boulder, Boulder County, and the Boulder Chamber of Commerce. This nonregulatory, incentive-based program provides industry with pollution prevention information and technical assistance necessary to reduce and/or eliminate environmental waste. This paper provides an overview of the program development, creation of partnerships and trust, and some of the results from implementation of the program. Following the first 18 months of the program, 35 businesses were recognized as Business Partners. The Business Partners program has also received an achievement award from the National Association of Counties for promoting {open_quotes}responsible, responsive, and effective government{close_quotes} and two governor`s awards from the State of Colorado. Participating businesses have demonstrated that a pollution prevention program can reduce environmental waste, increase employee safety, and decrease costs. 4 refs., 4 figs., 5 tabs.

Waste minimization and pollution prevention awareness plan

International Nuclear Information System (INIS)

1991-01-01

The purpose of this plan is to document the Lawrence Livermore National Laboratory (LLNL) Waste Minimization and Pollution Prevention Awareness Program. The plan specifies those activities and methods that are or will be employed to reduce the quantity and toxicity of wastes generated at the site. The intent of this plan is to respond to and comply with (DOE's) policy and guidelines concerning the need for pollution prevention. The Plan is composed of a LLNL Waste Minimization and Pollution Prevention Awareness Program Plan and, as attachments, Program- and Department-specific waste minimization plans. This format reflects the fact that waste minimization is considered a line management responsibility and is to be addressed by each of the Programs and Departments. 14 refs

Waste minimization and pollution prevention awareness plan

Energy Technology Data Exchange (ETDEWEB)

1991-05-31

The purpose of this plan is to document the Lawrence Livermore National Laboratory (LLNL) Waste Minimization and Pollution Prevention Awareness Program. The plan specifies those activities and methods that are or will be employed to reduce the quantity and toxicity of wastes generated at the site. The intent of this plan is to respond to and comply with (DOE's) policy and guidelines concerning the need for pollution prevention. The Plan is composed of a LLNL Waste Minimization and Pollution Prevention Awareness Program Plan and, as attachments, Program- and Department-specific waste minimization plans. This format reflects the fact that waste minimization is considered a line management responsibility and is to be addressed by each of the Programs and Departments. 14 refs.

33 CFR 151.19 - International Oil Pollution Prevention (IOPP) Certificates.

Science.gov (United States)

2010-07-01

... International Oil Pollution Prevention (IOPP) Certificates. (a) Each U.S. oil tanker of 150 gross tons and above... Oil Pollution Prevention (IOPP) Certificate. (b) Each oil tanker of 150 gross tons and above and each... construction, equipment, fittings, or arrangements required by the pollution prevention requirements of parts...

A proposed framework for conducting pollution prevention design assessments (P2DAs) on U.S. Department of Energy design projects

International Nuclear Information System (INIS)

Dorsey, J.A.

1995-03-01

The purpose of this manual is to provide a framework for project managers, engineers, and designers to integrate pollution prevention principles and features into DOE design projects. The framework suggested is referred to as the pollution prevention design assessment (P2DA). The P2DA is based on DOE's method for conducting pollution prevention opportunity assessments (PPOAs) on existing waste-generating operations, but the P2DA is modified because the facility or process it assesses does not physically exist during design. Before the P2DA framework is introduced in the manual, recommendations for establishing the P2DA team and budget are provided. Specific pollution prevention requirements and opportunities for each design stage as delineated in DOE Order 4700.1 Project Management System are also discussed and a sample format for drafting a P2DA report is provided in the appendix. The scope of this manual includes not only the P2DA framework, but also a background discussion of pollution prevention and related topics; the regulatory requirements mandating design for pollution prevention; the benefits and barriers of designing for pollution prevention; and the impact that pollution prevention and related environmental avoidance concepts have had on the engineering profession

Evidence-based integrated environmental solutions for secondary lead smelters: Pollution prevention and waste minimization technologies and practices

Energy Technology Data Exchange (ETDEWEB)

Genaidy, A.M., E-mail: world_tek_inc@yahoo.com [University of Cincinnati, Cincinnati, Ohio (United States); Sequeira, R. [University of Cincinnati, Cincinnati, Ohio (United States); Tolaymat, T. [U.S. Environmental Protection Agency, Office of Research and Development, Cincinnati, Ohio (United States); Kohler, J. [US Environmental Protection Agency, Office of Solid Waste and Emergency Response, Washington DC (United States); Rinder, M. [WorldTek Inc, Cincinnati (United States)

2009-05-01

An evidence-based methodology was adopted in this research to establish strategies to increase lead recovery and recycling via a systematic review and critical appraisal of the published literature. In particular, the research examines pollution prevention and waste minimization practices and technologies that meet the following criteria: (a) reduce/recover/recycle the largest quantities of lead currently being disposed of as waste, (b) technically and economically viable, that is, ready to be diffused and easily transferable, and (c) strong industry interest (i.e., industry would consider implementing projects with higher payback periods). The following specific aims are designed to achieve the study objectives: Aim 1 - To describe the recycling process of recovering refined lead from scrap; Aim 2 - To document pollution prevention and waste management technologies and practices adopted by US stakeholders along the trajectory of LAB and lead product life cycle; Aim 3 - To explore improved practices and technologies which are employed by other organizations with an emphasis on the aforementioned criteria; Aim 4 - To demonstrate the economic and environmental costs and benefits of applying improved technologies and practices to existing US smelting operations; and Aim 5 - To evaluate improved environmental technologies and practices using an algorithm that integrates quantitative and qualitative criteria. The process of identifying relevant articles and reports was documented. The description of evidence was presented for current practices and technologies used by US smelters as well as improved practices and technologies. Options for integrated environmental solutions for secondary smelters were introduced and rank ordered on the basis of costs (i.e., capital investment) and benefits (i.e., production increases, energy and flux savings, and reduction of SO2 and slag). An example was provided to demonstrate the utility of the algorithm by detailing the costs and

Evidence-based integrated environmental solutions for secondary lead smelters: pollution prevention and waste minimization technologies and practices.

Science.gov (United States)

Genaidy, A M; Sequeira, R; Tolaymat, T; Kohler, J; Rinder, M

2009-05-01

An evidence-based methodology was adopted in this research to establish strategies to increase lead recovery and recycling via a systematic review and critical appraisal of the published literature. In particular, the research examines pollution prevention and waste minimization practices and technologies that meet the following criteria: (a) reduce/recover/recycle the largest quantities of lead currently being disposed of as waste, (b) technically and economically viable, that is, ready to be diffused and easily transferable, and (c) strong industry interest (i.e., industry would consider implementing projects with higher payback periods). The following specific aims are designed to achieve the study objectives: Aim 1 - To describe the recycling process of recovering refined lead from scrap; Aim 2 - To document pollution prevention and waste management technologies and practices adopted by US stakeholders along the trajectory of LAB and lead product life cycle; Aim 3 - To explore improved practices and technologies which are employed by other organizations with an emphasis on the aforementioned criteria; Aim 4 - To demonstrate the economic and environmental costs and benefits of applying improved technologies and practices to existing US smelting operations; and Aim 5 - To evaluate improved environmental technologies and practices using an algorithm that integrates quantitative and qualitative criteria. The process of identifying relevant articles and reports was documented. The description of evidence was presented for current practices and technologies used by US smelters as well as improved practices and technologies. Options for integrated environmental solutions for secondary smelters were introduced and rank ordered on the basis of costs (i.e., capital investment) and benefits (i.e., production increases, energy and flux savings, and reduction of SO(2) and slag). An example was provided to demonstrate the utility of the algorithm by detailing the costs and

Purpose and methods of a Pollution Prevention Awareness Program

Energy Technology Data Exchange (ETDEWEB)

Flowers, P.A.; Irwin, E.F.; Poligone, S.E.

1994-08-15

The purpose of the Pollution Prevention Awareness Program (PPAP), which is required by DOE Order 5400.1, is to foster the philosophy that prevention is superior to remediation. The goal of the program is to incorporate pollution prevention into the decision-making process at every level throughout the organization. The objectives are to instill awareness, disseminate information, provide training and rewards for identifying the true source or cause of wastes, and encourage employee participation in solving environmental issues and preventing pollution. PPAP at the Oak Ridge Y-12 Plant was created several years ago and continues to grow. We believe that we have implemented several unique methods of communicating environmental awareness to promote a more active work force in identifying ways of reducing pollution.

Federalism and entrepreneurship: Explaining American and Canadian innovation in pollution prevention and regulatory integration

Energy Technology Data Exchange (ETDEWEB)

Rabe, B.G.

1999-07-01

Conventional wisdom provides an increasingly strong endorsement of far-reaching decentralization and delegation of authority to bureaucratic agents as the most likely mechanisms to attain such central environmental policy goals as pollution prevention,cross-media regulatory integration, and development of reliable measures of environmental outcomes. Canada would appear an unusually fertile context for such innovation, given its far-reaching deference to individual provinces and their environment ministries in environmental policy. Comparative analysis of select subnational governments in Canada and the United States suggests that the states in general are far ahead of their provincial counterparts in most of these areas of innovation. Despite all the opprobrium heaped on the American environmental policy system, a combination of federal policy tools and state policy entrepreneurship appear to contribute directly to this innovation in some states and are almost completely absent in the Canadian system. These findings suggest a need for careful study of the mix of intergovernmental policy tools and principal-agent relations most likely to realize desired environmental policy goals.

Waste Minimization and Pollution Prevention Awareness Plan

International Nuclear Information System (INIS)

1994-04-01

The purpose of this plan is to document Lawrence Livermore National Laboratory (LLNL) projections for present and future waste minimization and pollution prevention. The plan specifies those activities and methods that are or will be used to reduce the quantity and toxicity of wastes generated at the site. It is intended to satisfy Department of Energy (DOE) requirements. This Plan provides an overview of projected activities from FY 1994 through FY 1999. The plans are broken into site-wide and problem-specific activities. All directorates at LLNL have had an opportunity to contribute input, to estimate budget, and to review the plan. In addition to the above, this plan records LLNL's goals for pollution prevention, regulatory drivers for those activities, assumptions on which the cost estimates are based, analyses of the strengths of the projects, and the barriers to increasing pollution prevention activities

Pollution prevention: The role of a university

Energy Technology Data Exchange (ETDEWEB)

Barkenbus, J.N. [Univ. of Tennessee, Knoxville, TN (United States)

1995-12-01

Pollution prevention is at the top of the waste management hierarchy in the United States. If you don`t create pollution in the first place, concerns about transportation, treatment, storage, and disposal of waste are moot. While industry is on the front line in accomplishing significant pollution prevention, universities can play a meaningful role in its accomplishment as well. Universities can do this through three basic missions: education, research, and public service. Examples of how this is carried out at the University of Tennessee, Knoxville are provided. To be fully effective, universities need to organize in an interdisciplinary manner and adopt a public outreach agenda.

Pollution Prevention Successes Database (P2SDb) user guide

International Nuclear Information System (INIS)

1995-07-01

When Pollution Prevention Opportunity Assessments (P2OAs) were launched at the Hanford Site during the summer of 1994, the first comment received from those using them expressed the desire for a method to report assessments electronically. As a temporary measure, macros were developed for use on word processing systems, but a more formal database was obviously needed. Additionally, increased DOE and Washington state reporting requirements for pollution prevention suggested that a database system would streamline the reporting process. The Pollution Prevention Group of Westinghouse Hanford Company (WHC) contracted with the Data Automation Engineering Department from ICF Kaiser Hanford Company (ICFKH) to develop the system. The scope was to develop a database that will track P2OAs conducted by the facilities and contractors at the Hanford Site. It will also track pollution prevention accomplishments that are not the result of P2OAs and document a portion of the Process Waste Assessments conducted in the past. To accommodate the above criteria, yet complete the system in a timely manner, the Pollution Prevention Successes Database (P2SDb) is being implemented in three phases. The first phase will automate the worksheets to provide both input and output of the data associated with the worksheets. The second phase will automate standard summary reports and ad hoc reports. The third phase will provide automated searching of the database to facilitate the sharing of pollution prevention experiences among various users. This User's Guide addresses only the Phase 1 system

Environmental policies and the pollution prevention principle. Das Vorsorgeprinzip in der Umweltpolitik

Energy Technology Data Exchange (ETDEWEB)

Beyer, H M

1992-01-01

The pollution prevention principle has become the dominant environmental-policy guideline in the Federal Republic of Germany and in the European Communities. The compatibility of the pollution prevention principle with the dominating ecological-economics theory is analyzed, and the differences between the pollution prevention and the polluter principle as a significant, economically founded guideline are defined on the basis of the results obtained. The implementation of the pollution prevention principle, which is understood as an extensive ecologization of the socio-economic structures, is discussed evaluating the contribution of normative and empirical ethics and investigating three closely related aspects, i.e. the development of a pollution prevention target system, the suitability of environmental-policy instruments with regard to different levels of prevention, and the national and democratic institutional prerequisites. The prospects of the pollution prevention principle within the European Communities are discussed on the basis of these findings. (orig.).

Regulatory barriers to pollution prevention: A position paper of the implementation council of the American institute for pollution prevention

International Nuclear Information System (INIS)

Byers, R.L.

1991-01-01

Pollution prevention/waste minimization is a win-win-win situation for government, industry, and the public, which offers more than just protection of the environment for all. Industry gains from reduced capital and operating costs, reduced liabilities, cleaner and safer working conditions, conservation of energy and material resources, and the opportunity for government and industry to work together in a cooperative manner. However, a number of regulatory barriers exist which discourage pollution prevention/waste minimization. This paper provides examples for the aluminum, chemical, petroleum, and wood treating industries of how these regulatory barriers become disincentives. To promote pollusion prevention/waste minimization, Congress and the US EPA need to reexamine those RCRA provisions which support a command and control strategy that creates the barriers. The barriers include the distinction between value and valueless materials, offsite storage requirements prior to reuse/recycle, the Derived from Rule, the Burning for Fuel Rule, land ban technology standards, and RD and D restrictions. A new RCRA Pollution Prevention/Waste Minimization subtitle is proposed to eliminate or minimize these barriers

Design strategies for pollution prevention in industries (life cycle design)

International Nuclear Information System (INIS)

Saleemi, A.R.

1997-01-01

Pollution prevention and adoption of clean technologies in the industry are to be the proper strategies to flight against the growing industrial pollution in Pakistan. These strategies will not only reduce the existing pollution load and will also help to have sustainable industrial development in Pakistan in is well established that the concept of pollution prevention demands use of minimum, resources with maximum efficiency to achieve double benefits such as resource conservation and environmental protection. The application of cleaner production and waste minimization in thousand of industries in other part of world has proved beyond doubt that the use of cleaner technology is cheaper as compared to installation of waste treatment plants for end of pipe treatment. Waste treatment plants have been blamed not to solve any pollution problem, but only to transfer pollution from one environmental media to another. The adoption of waste treatment technologies have also created lot of other problems. Thousand of industries in the world have change their focus of activities from end of pipe treatment to pollution prevention techniques. It is the right time to start pollution prevention activities in industry. The design of a product system in the industry can be represented logically as a series of decision and choices made individually and collectively by design participant. The choices range from the selection of materials and manufacturing processes to choices relating to shape, from and function of a product. The product life cycle design provides a logical system for addressing pollution prevention because the full range of environmental consequence associated with the product can be considered and it is a powerful tool for identifying and maximizing the environmental benefits of pollution prevention. The life cycle assesment (LCA) concept suggests that decision making should be based on consideration of the cradle-to grave characteristics of the product, process

Waste minimization and pollution prevention awareness plan. Revision 1

International Nuclear Information System (INIS)

1994-07-01

The purpose of this plan is to document Lawrence Livermore National Laboratory (LLNL) projections for present and future waste minimization and pollution prevention. The plan specifies those activities and methods that are or will be used to reduce the quantity and toxicity of wastes generated at the site. It is intended to satisfy Department of Energy (DOE) requirements. This Waste Minimization and Pollution Prevention Awareness Plan provides an overview of projected activities from FY 1994 through FY 1999. The plans are broken into site-wide and problem-specific activities. All directorates at LLNL have had an opportunity to contribute input, estimate budgets, and review the plan. In addition to the above, this plan records LLNL's goals for pollution prevention, regulatory drivers for those activities, assumptions on which the cost estimates are based, analyses of the strengths of the projects, and the barriers to increasing pollution prevention activities

Pollution prevention program for new projects -- Lessons learned

Energy Technology Data Exchange (ETDEWEB)

Lum, J. [Dept. of Energy, Washington, DC (United States)

1993-03-01

The purpose of this presentation is to relay the experience of the Office of New Production Reactors (NP) in developing and implementing its pollution prevention program. NP was established to plan, design, and construct a new safe and environmentally acceptable nuclear reactor capacity necessary to provide an assured supply of tritium to maintain the nation`s long-term deterrent capability. The Program offered the Department of Energy an opportunity to demonstrate its commitment to environmental protection via minimization of environmental releases; new design offers the best opportunity for pollution prevention. The NP pollution prevention program was never fully implemented because NP`s tritium production design activity was recovery terminated. The information in this paper represented lessons learned from the last three years of NP operation.

Pollution prevention projects in the Netherlands

NARCIS (Netherlands)

de Bruijn, Theo; Coenen, Franciscus H.J.M.; Lulofs, Kristiaan R.D.

1996-01-01

As part of its waste matter prevention policy, the Dutch government has tried over the past few years to stimulate pollution prevention in firms by means of so-called stimulation and learning projects. To be able to determine the effectiveness of future policies, an extensive evaluation study was

46 CFR 184.702 - Pollution prevention equipment and procedures.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Pollution prevention equipment and procedures. 184.702 Section 184.702 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS... Pollution prevention equipment and procedures. A vessel must comply with the applicable design, equipment...

46 CFR 121.702 - Pollution prevention equipment and procedures.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Pollution prevention equipment and procedures. 121.702 Section 121.702 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS... CONTROL AND MISCELLANEOUS SYSTEMS AND EQUIPMENT Miscellaneous § 121.702 Pollution prevention equipment and...

Pollution prevention program plan 1996

International Nuclear Information System (INIS)

1996-01-01

This plan serves as the principal crosscutting guidance to Department of Energy (DOE) Headquarters, Operations Office, laboratory, and contractor management to fully implement pollution prevention programs within the DOE complex between now and 2000. To firmly demonstrate DOE's commitment to pollution prevention, the Secretary of Energy has established goals, to be achieved by December 31, 1999, that will aggressively reduce DOE's routine generation of radioactive, mixed, and hazardous wastes, and total releases and offsite transfers of toxic chemicals. The Secretary also has established sanitary waste reduction, recycling, and affirmative procurement goals. Site progress in meeting these goals will be reported annually to the Secretary in the Annual Report on Waste Generation and Waste Minimization Progress, using 1993 as the baseline year. Implementation of this plan will represent a major step toward reducing the environmental risks and costs associated with DOE operations

Environmental Restoration Program waste minimization and pollution prevention self-assessment

International Nuclear Information System (INIS)

1994-10-01

The Environmental Restoration (ER) Program within Martin Marietta Energy Systems, Inc. is currently developing a more active waste minimization and pollution prevention program. To determine areas of programmatic improvements within the ER Waste Minimization and Pollution Prevention Awareness Program, the ER Program required an evaluation of the program across the Oak Ridge K-25 Site, the Oak Ridge National Laboratory, the Oak Ridge Y-12 Plant, the Paducah Environmental Restoration and Waste Minimization Site, and the Portsmouth Environmental Restoration and Waste Minimization Site. This document presents the status of the overall program as of fourth quarter FY 1994, presents pollution prevention cost avoidance data associated with FY 1994 activities, and identifies areas for improvement. Results of this assessment indicate that the ER Waste Minimization and Pollution Prevention Awareness Program is firmly established and is developing rapidly. Several procedural goals were met in FY 1994 and many of the sites implemented ER waste minimization options. Additional growth is needed, however, for the ER Waste Minimization and Pollution Prevention Awareness Program

30 CFR 250.806 - Safety and pollution prevention equipment quality assurance requirements.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Safety and pollution prevention equipment... Gas Production Safety Systems § 250.806 Safety and pollution prevention equipment quality assurance... install only certified safety and pollution prevention equipment (SPPE) in wells located on the OCS. SPPE...

Transferring the Integrated Pollution Prevention and Control (IPPC Approach and Best Available Techniques (BAT Concepts to Egypt, Tunisia and Morocco

Directory of Open Access Journals (Sweden)

Víctor Vázquez Calvo

2013-07-01

Full Text Available The principles introduced by the Directive Concerning Integrated Pollution Prevention and Control (IPPC (currently known as the Industrial Emissions Directive (2010/75/EU are innovative and have raised interests in the framework of the literature debate on environmental regulation. Many articles describe and analyze the application of the Directive in European countries, but only a few articles focus on how the interest for the Directive’s principles, including the integrated approach, have reached countries outside the European Union. This paper aims to contribute to this topic, describing the experience of the authors in carrying out an EU-funded project on transferring the IPPC approach and Best Available Techniques (BAT concepts to three Arab countries, i.e., Egypt, Morocco and Tunisia. The paper presents the experience referring to two sectors falling within the scope of the IPPC Directive: the textile and dairy sector. The objectives, methodologies, activities and experiences are described and can be used and valorized to integrate the IPPC approach and BAT concepts in the current environmental legislation of the three countries.

48 CFR 52.223-5 - Pollution Prevention and Right-to-Know Information.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 2 2010-10-01 2010-10-01 false Pollution Prevention and... Provisions and Clauses 52.223-5 Pollution Prevention and Right-to-Know Information. As prescribed in 23.1005, insert the following clause: Pollution Prevention and Right-to-Know Information (AUG 2003) (a...

Web-based expert system for foundry pollution prevention

Science.gov (United States)

Moynihan, Gary P.

2004-02-01

Pollution prevention is a complex task. Many small foundries lack the in-house expertise to perform these tasks. Expert systems are a type of computer information system that incorporates artificial intelligence. As noted in the literature, they provide a means of automating specialized expertise. This approach may be further leveraged by implementing the expert system on the internet (or world-wide web). This will allow distribution of the expertise to a variety of geographically-dispersed foundries. The purpose of this research is to develop a prototype web-based expert system to support pollution prevention for the foundry industry. The prototype system identifies potential emissions for a specified process, and also provides recommendations for the prevention of these contaminants. The system is viewed as an initial step toward assisting the foundry industry in better meeting government pollution regulations, as well as improving operating efficiencies within these companies.

Annual report of waste generation and pollution prevention progress 1999

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-09-01

This Annual Report summarizes and highlights waste generation, waste reduction, pollution prevention accomplishments, and cost avoidance for 44 U.S. Department of Energy reporting sites for Calendar Year 1999. This section summarizes Calendar Year 1999 Complex-wide waste generation and pollution prevention accomplishments.

Annual report of waste generation and pollution prevention progress 1999

International Nuclear Information System (INIS)

2000-01-01

This Annual Report summarizes and highlights waste generation, waste reduction, pollution prevention accomplishments, and cost avoidance for 44 U.S. Department of Energy reporting sites for Calendar Year 1999. This section summarizes Calendar Year 1999 Complex-wide waste generation and pollution prevention accomplishments

Pollution Prevention Information Network (PPIN) Grant Summaries for 2011 and 2013

Science.gov (United States)

The Office of Pollution Prevention and Toxics is responsible for overseeing several grant programs for tribes and states which promote pollution prevention through source reduction and resource conservation.

Pollution prevention applications in batch manufacturing operations

Science.gov (United States)

Sykes, Derek W.; O'Shaughnessy, James

2004-02-01

Older, "low-tech" batch manufacturing operations are often fertile grounds for gains resulting from pollution prevention techniques. This paper presents a pollution prevention technique utilized for wastewater discharge permit compliance purposes at a batch manufacturer of detergents, deodorants, and floor-care products. This manufacturer generated industrial wastewater as a result of equipment rinses required after each product batch changeover. After investing a significant amount of capital on end of pip-line wastewater treatment technology designed to address existing discharge limits, this manufacturer chose to investigate alternate, low-cost approaches to address anticipated new permit limits. Mass balances using spreadsheets and readily available formulation and production data were conducted on over 300 products to determine how each individual product contributed to the total wastewater pollutant load. These mass balances indicated that 22 products accounted for over 55% of the wastewater pollutant. Laboratory tests were conducted to determine whether these same products could accept their individual changeover rinse water as make-up water in formulations without sacrificing product quality. This changeover reuse technique was then implement at the plant scale for selected products. Significant reductions in wastewater volume (25%) and wastewater pollutant loading (85+%) were realized as a direct result of this approach.

Role of the American Institute for Pollution Prevention in reducing environmental risk

International Nuclear Information System (INIS)

Hauser, T.R.

1991-01-01

The EPA Science Advisory Board recommended that in the decade of the 1990's, EPA strategy should focus on the long-term goal of preventing and reducing environmental risk and should shift from end-of-pipe controls to preventing the generation of pollution. To assist EPA in developing and implementing this philosophy, the American Institute for Pollution Prevention (AIPP) was founded jointly by EPA and the University of Cincinnati in June, 1989. The mission of the Institute is to generate broad support from private and public sectors and to assist EPA in achieving widespread and expeditious adoption of pollution prevention concepts. AIPP will provide a novel communication bridge between EPA and industry. AIPP will provide and promote liasion between professionals in the field of pollution and those who need to employ new and improved pollution prevention techniques

75 FR 63093 - Oil Pollution Prevention; Spill Prevention, Control, and Countermeasure (SPCC) Rule-Compliance...

Science.gov (United States)

2010-10-14

... Oil Pollution Prevention; Spill Prevention, Control, and Countermeasure (SPCC) Rule--Compliance Date... certain facilities must prepare or amend their Spill Prevention, Control, and Countermeasure (SPCC) Plans... facilities must prepare or amend their Spill Prevention, Control, and Countermeasure (SPCC) Plans (or ``Plan...

Hanford Site waste minimization and pollution prevention awareness program plan

International Nuclear Information System (INIS)

1994-05-01

The Hanford Site WMin/P2 program is an organized, comprehensive, and continual effort to systematically reduce the quantity and toxicity of hazardous, radioactive, mixed, and sanitary wastes; conserve resources; and prevent or minimize pollutant releases to all environmental media from all Site activities. The Hanford Site WMin/P2 program plan reflects national and DOE waste minimization and pollution prevention goals and policies, and represents an ongoing effort to make WMin/P2 part of the Site operating philosophy. In accordance with these policies, a hierarchical approach to environmental management has been adopted and is applied to all types of polluting and waste generating activities. Pollution prevention and waste minimization through source reduction are first priority in the Hanford WMin/P2 program, followed by environmentally safe recycling. Treatment to reduce the quantity, toxicity, and/or mobility will be considered only when prevention or recycling are not possible or practical. Environmentally safe disposal is the last option

GIS, Pollution Prevention and Public Health

Science.gov (United States)

Using examples of preventing pollution and reducing risk of exposure to communities, this guide answers basic interest and start-up questions, addresses benefits and limitations and illustrates the value of GIS for local health departments.

Pollution Prevention Guideline for Academic Laboratories.

Science.gov (United States)

Li, Edwin; Barnett, Stanley M.; Ray, Barbara

2003-01-01

Explains how to manage waste after a classroom laboratory experiment which generally has the potential to generate large amounts of waste. Focuses on pollution prevention and the selection processes to eliminate or minimize waste. (YDS)

40 CFR 52.2227 - Prevention of air pollution emergency episodes.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Prevention of air pollution emergency episodes. 52.2227 Section 52.2227 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS (CONTINUED) Tennessee § 52.2227 Prevention of air pollution emergency...

40 CFR 52.1934 - Prevention of air pollution emergency episodes.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Prevention of air pollution emergency episodes. 52.1934 Section 52.1934 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS (CONTINUED) Oklahoma § 52.1934 Prevention of air pollution emergency...

Pollution prevention opportunity assessments. Guidance for the Hanford Site

International Nuclear Information System (INIS)

Engel, J.A.

1994-10-01

The purpose of this document is to provide help to you, Hanford waste generators, in finding ways to reduce waste through Pollution Prevention (P2) and Pollution Prevention Opportunity Assessments (P2OAs). It is based on guidance from other sites, and serves to compliment the Hanford-specific training on P2OAs offered by the Pollution Prevention group at Westinghouse Hanford Company (WHC). The chapters of this document include help on how to choose major waste generating activities, how to conduct a P2OA, how to get results, and how to show progress. There is also a chapter on special situations and problems your facility may encounter. This first chapter tells you why you should consider conducting P2OAs and why they may be required

Developing the strategic plan for pollution prevention in defense programs

International Nuclear Information System (INIS)

Marchetti, John A.; Betschart, James F.; Suffern, J. Samuel

1992-01-01

In order to provide effective leadership and to ensure a consistent pollution prevention effort in all of its production facilities and laboratories, Defense Programs (DP) Headquarters, in close cooperation with the Field, has developed a strategic plan for its Pollution Prevention Program. The strategic plan is built upon the history of waste minimization, waste reduction, and pollution prevention activity to date, and articulates both long- and short-term strategies to ensure program initiation, growth, and stability. The organization of the program, including Headquarters staffing and linkages to the Geld, is described. Life-cycle analysis of program barriers and bottlenecks, along with associated initiatives and action plans are discussed. (author)

RESEARCH AREA -- ARTIFICIAL INTELLIGENCE CONTROL (AIR POLLUTION TECHNOLOGY BRANCH, AIR POLLUTION PREVENTION AND CONTROL DIVISION, NRMRL)

Science.gov (United States)

The Air Pollution Technology Branch (APTB) of NRMRL's Air Pollution Prevention and Control Division in Research Triangle Park, NC, has conducted several research projects for evaluating the use of artificial intelligence (AI) to improve the control of pollution control systems an...

40 CFR 52.1639 - Prevention of air pollution emergency episodes.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Prevention of air pollution emergency episodes. 52.1639 Section 52.1639 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS (CONTINUED) New Mexico § 52.1639 Prevention of air pollution emergency...

40 CFR 52.11 - Prevention of air pollution emergency episodes.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 3 2010-07-01 2010-07-01 false Prevention of air pollution emergency episodes. 52.11 Section 52.11 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS General Provisions § 52.11 Prevention of air pollution emergency episodes. ...

Pollution-Prevention Information Campaigns for Small Businesses: An Audience Analysis.

Science.gov (United States)

Boiarsky, Greg; Long, Marilee; Zimmerman, Donald E.

1999-01-01

Explores the results of a random phone survey of 300 small businesses in order to develop a pollution-prevention campaign. Results indicate that respondents understood the concept of pollution prevention and were taking steps to reduce their part in it. Businesses preferred to obtain their information from suppliers, publications, and other…

40 CFR 63.2495 - How do I comply with the pollution prevention standard?

Science.gov (United States)

2010-07-01

... Manufacturing Alternative Means of Compliance § 63.2495 How do I comply with the pollution prevention standard? (a) You may elect to comply with the pollution prevention alternative requirements specified in... comply by using the pollution prevention alternative must begin with the same starting material(s) and...

40 CFR Table 8 to Part 455 - List of Pollution Prevention Alternative Practices

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false List of Pollution Prevention... of Pollution Prevention Alternative Practices A modification to the list of practices on this table that an individual facility must comply with to be eligible for the pollution prevention alternative is...

Sandia National Laboratories, California Pollution Prevention Program annual report.

Energy Technology Data Exchange (ETDEWEB)

Harris, Janet S.; Farren, Laurie J.

2010-03-01

The annual program report provides detailed information about all aspects of the SNL/CA Pollution Prevention Program for a given calendar year. It functions as supporting documentation to the SNL/CA Environmental Management System Program Manual. The program report describes the activities undertaken during the past year, and activities planned in future years to implement the Pollution Prevention Program, one of six programs that supports environmental management at SNL/CA.

NASA LANGLEY RESEARCH CENTER AND THE TIDEWATER INTERAGENCY POLLUTION PREVENTION PROGRAM

Science.gov (United States)

National Aeronautics and Space Administration (NASA)'s Langley Research Center (LaRC) is an 807-acre research center devoted to aeronautics and space research. aRC has initiated a broad-based pollution prevention program guided by a Pollution Prevention Program Plan and implement...

Application of integrated GIS and multimedia modeling on NPS pollution evaluation.

Science.gov (United States)

Lin, C E; Kao, C M; Lai, Y C; Shan, W L; Wu, C Y

2009-11-01

In Taiwan, nonpoint source (NPS) pollution is one of the major causes of the impairment of surface waters. I-Liao Creek, located in southern Taiwan, flows approximately 90 km and drains toward the Kaoping River. Field investigation results indicate that NPS pollution from agricultural activities is one of the main water pollution sources in the I-Liao Creek Basin. Assessing the potential of NPS pollution to assist in the planning of best management practice (BMP) is significant for improving pollution prevention and control in the I-Liao Creek Basin. In this study, land use identification in the I-Liao Creek Basin was performed by properly integrating the skills of geographic information system (GIS) and global positioning system (GPS). In this analysis, 35 types of land use patterns in the watershed area of the basin are classified with the aid of Erdas Imagine process system and ArcView GIS system. Results indicate that betel palm farms, orchard farms, and tea gardens dominate the farmland areas in the basin, and are scattered around on both sides of the river corridor. An integrated watershed management model (IWMM) was applied for simulating the water quality and evaluating NPS pollutant loads to the I-Liao Creek. The model was calibrated and verified with collected water quality and soil data, and was used to investigate potential NPS pollution management plans. Simulated results indicate that NPS pollution has significant contributions to the nutrient loads to the I-Liao Creek during the wet season. Results also reveal that NPS pollution plays an important role in the deterioration of downstream water quality and caused significant increase in nutrient loads into the basin's water bodies. Simulated results show that source control, land use management, and grassy buffer strip are applicable and feasible BMPs for NPS nutrient loads reduction. GIS system is an important method for land use identification and waste load estimation in the basin. Linking the

77 FR 63803 - Federal Acquisition Regulation; Information Collection; Pollution Prevention and Right-to-Know...

Science.gov (United States)

2012-10-17

...; Information Collection; Pollution Prevention and Right-to-Know Information (FAR 52.223-5) AGENCY: Department... previously approved information collection requirement concerning pollution prevention and right-to-know..., Pollution Prevention and Right-to-Know Information'' on your attached document. Fax: 202-501-4067. Mail...

77 FR 52341 - Information Collection Activity: Subpart C, Pollution Prevention and Control; Submitted for...

Science.gov (United States)

2012-08-29

...-0001; OMB Number 1014-NEW] Information Collection Activity: Subpart C, Pollution Prevention and Control... the regulations under Subpart C, Pollution Prevention and Control. This notice also provides the... information. SUPPLEMENTARY INFORMATION: Title: 30 CFR 250, Subpart C, Pollution Prevention and Control. OMB...

Smart City Environmental Pollution Prevention and Control Design Based on Internet of Things

Science.gov (United States)

Peng, He; Bohong, Zheng; Qinpei, Kuang

2017-11-01

Due to increasingly serious urban pollution, this paper proposes an environmental pollution prevention and control system in combination with Internet of things. The system transfers data through the Internet, which also utilizes sensor, pH sensor and smoke sensor to obtain environmental data. Besides, combined with the video data acquired through monitoring, the data are transferred to data center to analyze the haze pollution, water pollution and fire disaster in environment. According to the results, multi-purpose vehicles are mobilized to complete the tasks such as spraying water to relieve haze, water source purification and fire fighting in city environment. Experiments show that the environmental pollution prevention and control system designed in this paper can automatically complete the urban environmental pollution detection, prevention and control, which thus reduces human and material resources and improves the efficiency of pollution prevention and control. Therefore, it possesses greatly practical significance to the construction of smart city.

Pollution Prevention Programs in Your Community.

Science.gov (United States)

Stenstrup, Al

1995-01-01

Provides details of an activity in which students in grades 5-12 study businesses in their community to discover what efforts are being made to reduce pollution. Integrates science and social studies content. (DDR)

A pollution prevention chargeback system at Sandia National Laboratories, New Mexico

International Nuclear Information System (INIS)

Davis, R.; Fish, J.; Brown, C.

1994-08-01

Sandia National Laboratories, New Mexico (Sandia/NM) has successfully developed and implemented a chargeback system to fund the implementation of Pollution Prevention activities. In the process of establishing this system, many valuable lessons have been learned. This paper describes how the chargeback system currently functions, the benefits and drawbacks of implementing such a system, and recommendations for implementing a chargeback system at other facilities. The initial goals in establishing a chargeback system were to create (1) funding for pollution prevention implementation, including specific pollution prevention projects; and (2) awareness on the part of the line organizations of the quantities and types of waste that they generate, thus providing them with a direct incentive to reduce that waste. The chargeback system inputs waste generation data and then filters and sorts the data to serve two purposes: (1) the operation of the chargeback system; and (2) the detailed waste generation reporting used for assessing processes and identifying pollution prevention opportunities

Environmental Restoration Contractor Waste Minimization and Pollution Prevention Plan

International Nuclear Information System (INIS)

Duvon, D. K.

1998-01-01

This plan contains the Pollution Prevention (P2) Program for the Environmental Restoration Contractor (ERC). The plan outlines the activities and schedules developed by the Bechtel Hanford, Inc.(BHI) to reduce the quantity and toxicity of waste dispositioned as a result of restoration and remediation activities. The purpose of this plan is to guide ERC projects in meeting and documenting compliance with requirements for pollution prevention. This plan contains the objectives, strategy, and support activities of the ERC P2 Program

The U.S. Department of Energy pollution prevention program: Applications for small business

Energy Technology Data Exchange (ETDEWEB)

Betsch, M.D.

1997-05-14

This report shows the benefits small businesses can realize by instituting cost-effective pollution prevention improvements. It is a series of pollution prevention assessments that were conducted at small businesses in Richland, Washington. It describes a technology transfer test of US Department of Energy (USDOE) pollution prevention methods to small businesses through eleven pollution prevention assessments conducted at small businesses in the city of Richland. The assessment method tested was first developed at the USDOE Hanford Site, located in Richland, Washington. Two pilot studies were initially conducted to determine the usefulness of the assessment method for small businesses. Then, four additional pollution prevention assessments were conducted using a refined process. In order to determine the assessment method`s usefulness by different practitioners, a number of the assessments contained in this report were conducted by the undergraduate and graduate students at Washington State University at Tri-Cities as part of their class projects. These students were trained in the pollution prevention assessment process by the author of this report and conducted five small business assessments using the same methods and materials as in the remainder of the study.

The U.S. Department of Energy pollution prevention program: Applications for small business

International Nuclear Information System (INIS)

Betsch, M.D.

1997-01-01

This report shows the benefits small businesses can realize by instituting cost-effective pollution prevention improvements. It is a series of pollution prevention assessments that were conducted at small businesses in Richland, Washington. It describes a technology transfer test of US Department of Energy (USDOE) pollution prevention methods to small businesses through eleven pollution prevention assessments conducted at small businesses in the city of Richland. The assessment method tested was first developed at the USDOE Hanford Site, located in Richland, Washington. Two pilot studies were initially conducted to determine the usefulness of the assessment method for small businesses. Then, four additional pollution prevention assessments were conducted using a refined process. In order to determine the assessment method's usefulness by different practitioners, a number of the assessments contained in this report were conducted by the undergraduate and graduate students at Washington State University at Tri-Cities as part of their class projects. These students were trained in the pollution prevention assessment process by the author of this report and conducted five small business assessments using the same methods and materials as in the remainder of the study

Chemicals and excess materials disposition during deactivation as a means of pollution prevention

International Nuclear Information System (INIS)

Godfrey, S.D.

1998-01-01

This paper presents several innovative and common sense approaches to pollution prevention that have been employed during facility deactivation at the Hanford Site in South Central Washington. It also presents several pollution prevention principles applicable to other projects. Innovative pollution prevention ideas employed at the Hanford site during facility deactivation included: (1) Recycling more than 185,000 gallons of radioactively contaminated nitric acid by sending it to an operating nuclear fuels reprocessing facility in England; (2) Recycling millions of pounds of chemicals and excess materials to other industries for reuse; (3) Evaporating flush water at a low rate and discharging it into the facility exhaust air stream to avoid discharging thousands of gallons of liquid to the soil column; and (4) Decontaminating and disposing of thousands of gallons of radioactively contaminated organic solvent waste to a RCRA licensed, power-producing, commercial incinerator. Common sense pollution prevention ideas that were employed include recycling office furniture, recycling paper from office files, and redeploying tools and miscellaneous process equipment. Additional pollution prevention occurred as the facility liquid and gaseous discharge streams were deactivated. From the facilities deactivation experiences at Hanford and the ensuing efforts to disposition excess chemicals and materials, several key pollution prevention principles should be considered at other projects and facilities, especially during the operational periods of the facility's mission. These principles include: Institute pollution prevention as a fundamental requirement early in the planning stage of a project or during the operational phase of a facility's mission; Promote recognition and implementation of pollution prevention initiatives; Instill pollution prevention as a value in all participants in the project or facility work scope; Minimize the amount of chemical products and materials

Hanford Site pollution prevention progress report 1999

International Nuclear Information System (INIS)

BETSCH, M.D.

1999-01-01

The Richland Operations Office (RL) and Office of River Protection (ORP) are pleased to issue the attached Pollution Prevention Progress Report. We have just met the most aggressive waste reduction and A recycling goals to date and are publishing this report to recognize A the site's progress, and to ensure it will sustain success beyond 1 Fiscal Year 2000. This report was designed to inform the been made by RL and ORP in Waste Minimization (WMin) and Pollution Prevention (P2). RL, ORP and their contractors are committed to protecting the environment, and we reiterate pollution prevention should continue to be at the forefront of the environmental cleanup and research efforts. As you read the attached report, we believe you will see a clear demonstration of RL and ORP's outstanding performance as it has been responsible and accountable to the nation, its employees, and the community in which we live and work. commitment that all employees have for environmental stewardship. The report provides useful information about the U.S. Department of Energy's (DOE'S) environmental policy and programs, and contains countless examples of waste minimization projects. This year was the first year our site received the White House Closing the Circle in the category of Affirmative Procurement. This Award recognizes our site for designing a comprehensive strategy for achieving 100 percent purchases of the U.S.Environmenta1 Protection Agency designated recycled items. DOE-Headquarters also acknowledged the site in 1999 for its public outreach efforts in communicating pollution prevention to Hanford Site employees and the community. Our site is truly a recognized leader in outreach as it has kept this title for two consecutive years. In previous years, we received the White House Closing the Circle Honorable Mention in Affirmative Procurement and several other National DOE Awards. Through partnership with the local community and stakeholders, the site and its contractors have a clear

Hanford Site pollution prevention progress report; FINAL

International Nuclear Information System (INIS)

BETSCH, M.D.

1999-01-01

The Richland Operations Office (RL) and Office of River Protection (ORP) are pleased to issue the attached Pollution Prevention Progress Report. We have just met the most aggressive waste reduction and A recycling goals to date and are publishing this report to recognize A the site's progress, and to ensure it will sustain success beyond 1 Fiscal Year 2000. This report was designed to inform the been made by RL and ORP in Waste Minimization (WMin) and Pollution Prevention (P2). RL, ORP and their contractors are committed to protecting the environment, and we reiterate pollution prevention should continue to be at the forefront of the environmental cleanup and research efforts. As you read the attached report, we believe you will see a clear demonstration of RL and ORP's outstanding performance as it has been responsible and accountable to the nation, its employees, and the community in which we live and work. commitment that all employees have for environmental stewardship. The report provides useful information about the U.S. Department of Energy's (DOE'S) environmental policy and programs, and contains countless examples of waste minimization projects. This year was the first year our site received the White House Closing the Circle in the category of Affirmative Procurement. This Award recognizes our site for designing a comprehensive strategy for achieving 100 percent purchases of the U.S.Environmenta1 Protection Agency designated recycled items. DOE-Headquarters also acknowledged the site in 1999 for its public outreach efforts in communicating pollution prevention to Hanford Site employees and the community. Our site is truly a recognized leader in outreach as it has kept this title for two consecutive years. In previous years, we received the White House Closing the Circle Honorable Mention in Affirmative Procurement and several other National DOE Awards. Through partnership with the local community and stakeholders, the site and its contractors have a clear

Annual report of waste generation and pollution prevention progress 2000 [USDOE] [9th edition

International Nuclear Information System (INIS)

None

2001-01-01

This ninth edition of the Annual Report of Waste Generation and Pollution Prevention Progress highlights waste reduction, pollution prevention accomplishments, and cost savings/avoidance for the U.S. Department of Energy (DOE) Pollution Prevention Program for Fiscal Year 2000. This edition marks the first time that progress toward meeting the 2005 Pollution Prevention Goals, issued by the Secretary of Energy in November 1999, is being reported. In addition, the Annual Report has a new format, and now contains information on a fiscal year basis, which is consistent with other DOE reports

Potential pollution prevention and waste minimization for Department of Energy operations

International Nuclear Information System (INIS)

Griffin, J.; Ischay, C.; Kennicott, M.; Pemberton, S.; Tull, D.

1995-10-01

With the tightening of budgets and limited resources, it is important to ensure operations are carried out in a cost-effective and productive manner. Implementing an effective Pollution Prevention strategy can help to reduce the costs of waste management and prevent harmful releases to the environment. This document provides an estimate of the Department of Energy's waste reduction potential from the implementation of Pollution Prevention opportunities. A team of Waste Minimization and Pollution Prevention professionals was formed to collect the data and make the estimates. The report includes a list of specific reduction opportunities for various waste generating operations and waste types. A generic set of recommendations to achieve these reduction opportunities is also provided as well as a general discussion of the approach and assumptions made for each waste generating operation

Pollution prevention and waste minimization opportunity assessment in environmental restoration

International Nuclear Information System (INIS)

Roybal, J.A.; Willison, C.P.

1997-01-01

The Environmental Restoration (ER) Project at Sandia National Laboratories implicitly subscribed to the philosophy of pollution prevention and waste minimization. As a result of a Department of Energy (DOE) offer, Pollution Prevention Opportunity Assessments (PPOA) were conducted at two ER sites and a decontamination and Demolition (D and D) site. The purpose of one of the PPOAs was to identify pollution prevention (P2) opportunities during environmental remediation at the Classified Waste Landfill located at Sandia National Laboratories, New Mexico (SNL/NM). The remediation activities at this site are scheduled to begin in the fall of 1997. The PPOA included presentations by the team members, a tour of the site, and a brainstorming session to list the waste streams, identify P2 opportunities and rank them in order of priority. Twenty-five P2 opportunities were identified during the brainstorming session of which twenty-two opportunities were selected for further investigation. Those twenty-two opportunities are discussed in this paper. A cost benefit analysis was performed for each P2 opportunity based on the estimated waste volume, feasibility, and cost. Pollution Prevention by Design (P2D) was incorporated into the PPOA to introduce waste minimization techniques that can be used during the planning phase of restoration projects

Pollution prevention opportunity assessment benchmarking: Recommendations for Hanford

Energy Technology Data Exchange (ETDEWEB)

Engel, J.A.

1994-05-01

Pollution Prevention Opportunity Assessments (P2OAs) are an important first step in any pollution prevention program. While P2OAs have been and are being conducted at Hanford, there exists no standard guidance, training, tracking, or systematic approach to identifying and addressing the most important waste streams. The purpose of this paper then is to serve as a guide to the Pollution Prevention group at Westinghouse Hanford in developing and implementing P2OAs at Hanford. By searching the literature and benchmarks other sites and agencies, the best elements from those programs can be incorporated and pitfalls more easily avoided. This search began with the 1988 document that introduces P2OAs (then called Process Waste Assessments, PWAS) by the Environmental Protection Agency. This important document presented the basic framework of P20A features which appeared in almost all later programs. Major Department of Energy programs were also examined, with particular attention to the Defense Programs P20A method of a graded approach, as presented at the Kansas City Plant. The graded approach is a system of conducting P2OAs of varying levels of detail depending on the size and importance of the waste stream. Finally, private industry programs were examined briefly. While all the benchmarked programs had excellent features, it was determined that the size and mission of Hanford precluded lifting any one program for use. Thus, a series of recommendations were made, based on the literature review, in order to begin an extensive program of P2OAs at Hanford. These recommendations are in the areas of: facility Pollution Prevention teams, P20A scope and methodology, guidance documents, training for facilities (and management), technical and informational support, tracking and measuring success, and incentives.

Safety installation for preventing pollution by pipelines

Energy Technology Data Exchange (ETDEWEB)

Wittgenstein, G F

1972-10-25

A safety installation for preventing pollution by pipelines, particularly those used for transporting liquid hydrocarbons, is described. It is applicable to any pipeline, but particularly to underground or submarine pipelines, whether made of steel, plastics, or any other material. The 4 essential objects of the invention are to insure reliable prevention of pollution of the environment due to leakage of a hydrocarbon through cracks in the pipe; to evacuate the leakage flow without delay to a vessel; to signal almost instantaneously the existence of a leak; and to effect remote control of operations by which the dynamic pressure in the pipe is cancelled. Each equipped section consists of a fluid-type jacket of plastic material which surrounds the pipe, which at its ends is sealed off. It is these seals which delimit the sections. (7 claims)

DEVELOPMENT OF THE U.S. EPA'S METAL FINISHING FACILITY POLLUTION PREVENTION TOOL

Science.gov (United States)

Metal finishing processes are a type of chemical processes and can be modeled using Computer Aided Process Engineering (CAPE). Currently, the U.S. EPA is developing the Metal Finishing Facility Pollution Prevention Tool (MFFP2T), a pollution prevention software tool for the meta...

Prevention and Control of Agricultural Non-Point Source Pollutions in UK and Suggestions to China

OpenAIRE

Liu, Kun; Ren, Tianzhi; Wu, Wenliang; Meng, Fanquiao; Bellarby, Jessica; Smith, Laurence

2016-01-01

Currently, the world is facing challenges of maintaining food production growth while improving agricultural ecological environmental quality. The prevention and control of agricultural non-point source pollution, a key component of these challenges, is a systematic program which integrates many factors such as technology and its extension, relevant regulation and policies. In the project of UK-China Sustainable Agriculture Innovation Network, we undertook a comprehensive analysis of the prev...

76 FR 18894 - Oil Pollution Prevention

Science.gov (United States)

2011-04-06

... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 112 Oil Pollution Prevention CFR Correction In Title 40 of the Code of Federal Regulations, Parts 100 to 135, revised as of July 1, 2010, on page 71, in Appendix E to Part 112, the second section 5.1 is removed. [FR Doc. 2011-8328 Filed 4-5-11; 8:45 am...

A computer based system for prioritizing pollution prevention opportunity assessments at SNL/NM

International Nuclear Information System (INIS)

Custer, M.S.; Leishman, N.L.; Walsh, M.L.; Nelson, J.D.; Davis, R.L.; Bueno, N.C.

1996-01-01

Prioritizing waste generators is necessary to determine which are the best candidates for Pollution Prevention Opportunity Assessments (PPOAs). This paper describes the Sandia National Laboratories/New Mexico (SNL/NM) PPOA Ranking System. The system uses a multimedia approach that considers hazardous and radioactive waste disposal data, and hazardous chemical usage data (from which air emissions are extrapolated). Pollution prevention information is included, from the SNL Pollution Prevention Opportunities database that identifies waste streams that have readily apparent pollution prevention opportunities. The system also considers the relative costs of waste management and the chargeback fees paid for waste generation. From these data, organizations are ranked with an algorithm developed in Microsoft Access trademark on a personal computer. The concept could readily be transferred to other facilities needing to decide where to perform PPOAs

Pollution prevention and industrial transformation; Evoking structural changes within companies

NARCIS (Netherlands)

de Bruijn, Theo; Hofman, Peter

2000-01-01

Pollution prevention has developed as an attractive method for improving the environmental performance of companies. Often the concept is promoted in a project format, for instance in a regional perspective or for a specific sector of industry. This article analyzes the contribution of pollution

78 FR 30304 - Federal Acquisition Regulation; Submission for OMB Review; Pollution Prevention and Right-to-Know...

Science.gov (United States)

2013-05-22

...; Submission for OMB Review; Pollution Prevention and Right-to-Know Information (FAR 52.223-5) AGENCY... previously approved information collection requirement concerning pollution prevention and right-to-know... by Information Collection 9000- 0147, Pollution Prevention and Right-to-Know Information by any of...

Report: EPA Needs Accurate Data on Results of Pollution Prevention Grants to Maintain Program Integrity and Measure Effectiveness of Grants

Science.gov (United States)

Report #15-P-0276, September 4, 2015. Inaccurate reporting of results misrepresents the impacts of pollution prevention activities provided to the public, and misinforms EPA management on the effectiveness of its investment in the program.

Hanford site pollution prevention plan progress report, 1993

Energy Technology Data Exchange (ETDEWEB)

Kirkendall, J.R.

1996-08-26

This report tracks progress made during 1995 against the goals stated in DOE/RL-92-62, Executive Summary, Hanford Site Pollution Prevention Plan. The Executive Summary of the plan was submitted to the Washington State Department of Ecology (Ecology) in September 1992. The plan, Executive Summary, and the progress reports are elements of a pollution prevention planning program that is required by WAC 173-307,`Plans,` for all hazardous substance users and/or all hazardous waste generators regulated by Ecology. These regulations implement RCW 70.95C, `Waste Reduction,` an act relating to hazardous waste reduction. The act encourages voluntary efforts to redesign industrial processes to help reduce or eliminate hazardous substances and hazardous waste byproducts, and to maximize the in- process reuse or reclamation of valuable spent material.

Hanford Site Guide for Preparing and Maintaining Fenerator Group Pollution Prevention Program Documentation

International Nuclear Information System (INIS)

PLACE, B.G.

1999-01-01

This document provides guidance to generator groups for preparing and maintaining documentation of Pollution Prevention/Waste Minimization (P2/WMin) Program activities. The guidance is one of a hierarchical series that includes the Hanford Site Waste Minimization and Pollution Prevention Awareness Program Plan (DOE-RL, 1998a) and Prime Contractor implementation plans describing programs required by Resource Conservation and Recovery Act of 1976 (RCRA) 3002(b) and (300501) (RCRA and EPA, 1994). Documentation guidance for the following five P2/WMin elements are discussed: Fiscal Year (FY) Goals; Budget and Staffing; Waste Minimization (WMinn ) Assessments (WMAs); Pollution Prevention (P2) Reporting; WMin Certification

Recent developments in the DOE Waste Minimization Pollution Prevention Program

International Nuclear Information System (INIS)

Hancock, J.K.

1993-01-01

The U.S. Department of Energy (DOE) is involved in a wide variety of research and development, remediation, and production activities at more than 100 sites throughout the United States. The wastes generated cover a diverse spectrum of sanitary, hazardous, and radioactive waste streams, including typical office environments, power generation facilities, laboratories, remediation sites, production facilities, and defense facilities. The DOE's initial waste minimization activities pre-date the Pollution Prevention Act of 1990 and focused on the defense program. Little emphasis was placed on nonproduction activities. In 1991 the Office of Waste Management Operations developed the Waste Minimization Division with the intention of coordinating and expanding the waste minimization pollution prevention approach to the entire complex. The diverse nature of DOE activities has led to several unique problems in addressing the needs of waste minimization and pollution prevention. The first problem is developing a program that addresses the geographical and institutional hurdles that exist; the second is developing a monitoring and reporting mechanism that one can use to assess the overall performance of the program

Hanford Site Guide for Preparing and Maintaining Generator Group Pollution Prevention Documentation

International Nuclear Information System (INIS)

PLACE, B.G.

2000-01-01

This document provides guidance to generator groups for preparing and maintaining documentation of Pollution Prevention/Waste Minimization (P2/WMin) Program activities. The guidance is one of a hierarchical series that includes the Hanford Site Waste Minimization and Pollution Prevention Awareness Program Plan (DOE-RL, 2000) and Prime Contractor implementation plans describing programs required by Resource Conservation and Recovery Act of 1976 (RCRA) 3002(b) and 3005(h) (RCRA and EPA, 1994) and Department of Energy Acquisition Regulations (DEAR) (48 CFR 970.5204-2 and 48 CFR 970.5204-78). Documentation guidance for the following five P2/WMin elements is discussed: Fiscal Year (FY) Goals; Budget and Staffing; Pollution Prevention (P2) Reporting; WMin Certification; and Waste Minimization (WMin) Assessments (WMAs)

Design an effective storm water pollution prevention plan

International Nuclear Information System (INIS)

Vivona, M.A.

1995-01-01

A case history shows ''how'' to plan and organize a storm water pollution prevention program (SWPPP). Using easy-to-use worksheets and guidelines, hydrocarbon processing industry (HPI) operators can build upon existing best management practices (i.e., housekeeping procedures, visual inspections, spill prevention programs, etc.) to meet tighter restrictions set by National Pollutant Discharge Elimination system (NPDES) permits. Especially in high rainfall areas, storm water poses an intermittent, but large volume problem. The facility's site size is another factor that impacts the scope and cost for SWPPP. The five steps to implementing a SWPPP are: Planning and organization; Assessment; Best management practice (BMP) identification; Implementation; Evaluation and monitoring. Initially, HPI operators must identify all potential contamination sources and past spills and leak areas. Following the SWPP guidelines, operators can map out a cost-effective storm water program that meets all NPDES requirements

Hanford Site guide for preparing and maintaining generator group pollution prevention program documentation

International Nuclear Information System (INIS)

Place, B.G.

1998-01-01

This document provides guidance to generator groups for preparing and maintaining documentation of Pollution Prevention Waste Minimization (P2/WMin) Program activities. The guidance is one of a hierarchical series that includes the Hanford Site Waste Minimization and Pollution Prevention Awareness Program Plan (DOE-RL, 1998a) and Prime contractor implementation plans describing programs required by Resource Conservation and Recovery Act of 1976 (RCRA) 3002(b) and 3005(h) (RCRA and EPA, 1994). Documentation guidance for the following five P2/WMin elements are discussed: Fiscal Year (FY) Goals; Budget and Staffing; Waste Minimization (WMin) Assessments (WMAs); Quarterly Pollution Prevention (P2) Reporting WMin Certification

Mine water pollution in Scotland. Nature, extent and preventative strategies

Energy Technology Data Exchange (ETDEWEB)

Younger, P.L. [Water Resource Systems Research Laboratory, Department of Civil Engineering, University of Newcastle, NE1 7RU Newcastle Upon Tyne (United Kingdom)

2001-01-29

Scotland was one of the world's first industrialised countries, and has therefore also been one of the first countries to experience wholesale post-industrial dereliction. Water pollution arising from abandoned mines, particularly abandoned coal mines, is second only to sewage as a source of freshwater pollution nation-wide, and in many coalfield catchments it is the pre-eminent source. Most of the pollution is due to net-alkaline ferruginous waters emerging from deep mines. Scrutiny of records from 80 deep mine discharges reveals that iron concentrations in these waters are only likely to exceed 20 mg/l, and the pH to be below 6.5, where the discharge emerges within 0.5 km of the outcrop of the shallowest mined seam. The bulk of mature near-outcrop mine water discharges in Scotland have<50 mg/l total Fe, and concentrations>100 mg/l are only likely where a marine bed lies within 25 m of the worked seam. Where the nearest marine bed is more than 80 m above or below the seam, then the total iron will be less than 4 mg/l, and in most cases less than 1 mg/l. Net-acidic mine waters are far more rare than net-alkaline waters in Scotland, and are most commonly associated with unreclaimed spoil heaps (bings). Both net-alkaline and net-acidic discharges have detrimental effects on the hydrochemistry and biological integrity of receiving waters. Scotland has recently pioneered the use of pre-emptive pump-and-treat solutions to prevent mine water pollution, and has also experienced the successful introduction of passive treatment technology for both abandoned and active workings.

Pollution prevention and control procedure case study: an application for petroleum refineries.

Science.gov (United States)

Rodríguez, Encarnación; Martínez, Jose-Luis

2005-06-01

There is global environmental concern about the pollution from industries and other organizations that should not only be controlled but also prevented. Many alternatives are available to those in charge of environmental protection, but they should be able to draw on a systematic procedure to help implement prevention and control measures. At present, there are three immediate tasks: defining the objective of any environmental study, identifying the potential pollution sources, and selecting alternatives to these sources. However, it is necessary to evaluate these alternatives by using as large a number of criteria as possible and making them cumulative so as to enable the classification and selection of the best available techniques for each pollution source. The petroleum refining industry plays an important role in the developed economies and also has a potential for pollution generation that must be controlled. The best solution for all (i.e., petroleum companies, the public, and the environment) is pollution prevention, because this option will protect all of them and will also reduce costs in terms of lower raw materials consumption as well as reducing potential fines. The procedure we have presented in this article has been applied successfully.

Pollution prevention opportunity assessment for Technical Art

International Nuclear Information System (INIS)

Torres, H.M.

1995-09-01

This pollution prevention opportunity assessment was conducted to evaluate Technical Art, which is part of the Technical Communications Department at Sandia National Laboratories/California. It is located in Building 912, Room 138. This assessment documents the processes, identifies the hazardous chemical waste streams generated by these processes, and recommends possible ways to minimize waste

Pollution prevention opportunity assessment for Sandia National Laboratories/California recycling programs.

Energy Technology Data Exchange (ETDEWEB)

Wrons, Ralph Jordan; Vetter, Douglas Walter

2007-07-01

This Pollution Prevention Opportunity Assessment (PPOA) was conducted for the Sandia National Laboratories/California (SNL/CA) Environmental Management Department between May 2006 and March 2007, to evaluate the current site-wide recycling program for potential opportunities to improve the efficiency of the program. This report contains a summary of the information collected and analyses performed with recommended options for implementation. The SNL/NM Pollution Prevention (P2) staff worked with the SNL/CA P2 Staff to arrive at these options.

Air Pollution Prevention and Control Policy in China.

Science.gov (United States)

Huang, Cunrui; Wang, Qiong; Wang, Suhan; Ren, Meng; Ma, Rui; He, Yiling

2017-01-01

With rapid urbanization and development of transport infrastructure, air pollution caused by multiple-pollutant emissions and vehicle exhaust has been aggravated year by year in China. In order to improve air quality, the Chinese authorities have taken a series of actions to control air pollution emission load within a permissible range. However, although China has made positive progress on tackling air pollution, these actions have not kept up with its economy growth and fossil-fuel use. The traditional single-pollutant approach is far from enough in China now, and in the near future, air pollution control strategies should move in the direction of the multiple-pollutant approach. In addition, undesirable air quality is usually linked with the combination of high emissions and adverse weather conditions. However, few studies have been done on the influence of climate change on atmospheric chemistry in the global perspective. Available evidence suggested that climate change is likely to exacerbate certain kinds of air pollutants including ozone and smoke from wildfires. This has become a major public health problem because the interactions of global climate change, urban heat islands, and air pollution have adverse effects on human health. In this chapter, we first review the past and current circumstances of China's responses to air pollution. Then we discuss the control challenges and future options for a better air quality in China. Finally, we begin to unravel links between air pollution and climate change, providing new opportunities for integrated research and actions in China.

e-compendium - Air Pollution Prevention in an International and EU Environmental Law Perspective, Summer 2014

DEFF Research Database (Denmark)

Steen, Ulla

2014-01-01

E-compendium Air Pollution Prevention in an International and EU Environmental Law Perspective, Summer 2014......E-compendium Air Pollution Prevention in an International and EU Environmental Law Perspective, Summer 2014...

Pollution prevention/waste minimization program 1998 fiscal year work plan - WBS 1.11.2.1

International Nuclear Information System (INIS)

Howald, S.C.; Merry, D.S.

1997-09-01

Pollution Prevention/Waste Minimization (P2/WMin) is the Department of Energy's preferred approach to environmental management. The P2/WMin mission is to eliminate or minimize waste generation, pollutant releases to the environment, use of toxic substances, and to conserve resources by implementing cost-effective pollution prevention technologies, practices, and polices

Annual report of waste generation and pollution prevention progress, 1994

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-09-01

This Report summarizes the waste generation and pollution prevention activities of the major operational sites in the Department of Energy (DOE). We are witnessing progress in waste reduction from routine operations that are the focus of Department-wide reduction goals set by the Secretary on May 3,1996. The goals require that by the end of 1999, we reduce, recycle, reuse, and otherwise avoid waste generation to achieve a 50 percent reduction over 1993 levels. This Report provides the first measure of our progress in waste reduction and recycling against our 1993 waste generation baseline. While we see progress in reducing waste from our normal operations, we must begin to focus attention on waste generated by cleanup and facilities stabilization activities that are the major functions of the Office of Environmental Management. Reducing the generation of waste is one of the seven principles that I have established for the Office of Environmental Management Ten Year Plan. As part of our vision to complete a major portion of the environmental cleanup at DOE sites over the next ten years, we must utilize the potential of the pollution prevention program to reduce the cost of our cleanup program. We have included the Secretarial goals as part of the performance measures for the Ten Year Plan, and we are committed to implementing pollution prevention ideas. Through the efforts of both Federal and contractor employees, our pollution prevention program has reduced waste and the cost of our operations. I applaud their efforts and look forward to reporting further waste reduction progress in the next annual update of this Report.

Annual report of waste generation and pollution prevention progress, 1994

International Nuclear Information System (INIS)

1996-09-01

This Report summarizes the waste generation and pollution prevention activities of the major operational sites in the Department of Energy (DOE). We are witnessing progress in waste reduction from routine operations that are the focus of Department-wide reduction goals set by the Secretary on May 3,1996. The goals require that by the end of 1999, we reduce, recycle, reuse, and otherwise avoid waste generation to achieve a 50 percent reduction over 1993 levels. This Report provides the first measure of our progress in waste reduction and recycling against our 1993 waste generation baseline. While we see progress in reducing waste from our normal operations, we must begin to focus attention on waste generated by cleanup and facilities stabilization activities that are the major functions of the Office of Environmental Management. Reducing the generation of waste is one of the seven principles that I have established for the Office of Environmental Management Ten Year Plan. As part of our vision to complete a major portion of the environmental cleanup at DOE sites over the next ten years, we must utilize the potential of the pollution prevention program to reduce the cost of our cleanup program. We have included the Secretarial goals as part of the performance measures for the Ten Year Plan, and we are committed to implementing pollution prevention ideas. Through the efforts of both Federal and contractor employees, our pollution prevention program has reduced waste and the cost of our operations. I applaud their efforts and look forward to reporting further waste reduction progress in the next annual update of this Report

Governance by Green Taxes: Making Pollution Prevention Pay

DEFF Research Database (Denmark)

Andersen, Mikael Skou

a comparative study of the water policies of Denmark, France, Germany and the Netherlands, he shows how, in contrast to administrative regulation, green taxes have made pollution prevention pay and promoted the "ecological modernization" of industry. He goes on, however, to challenge the prevailing orthodoxy...

Joint Group on Pollution Prevention: Partnering for Progress

Science.gov (United States)

Hill, R.

2001-01-01

This viewgraph presentation outlines the Joint Group on Pollution Prevention (JG-PP) partnership. Details are given on what groups comprise JG-PP, the proven methodology for what JG-PP can accomplish, the common problems, joint solutions, and shared efforts, and some of the JG-PP projects.

Electric Arc Furnace as a Source of Emission of Polychlorinated Dibenzo-p-Dioxins and Polychlorinated Dibenzofurans in Perspective of the Council Directive 96/61 EC Concerning Integrated Pollution Prevention and Control

Directory of Open Access Journals (Sweden)

Sofilić, T.

2008-01-01

Full Text Available As the accumulation of PCDDs/Fs in the natural environment poses a great threat, and the pollution of the environment with these highly toxic compounds from various emitters needs to be prevented, many countries have conducted an inventory of industrial sources and their emissions in order to obtain better insight into the share of particular sources in the total emission of PCDDs/Fs and to develop strategies to reduce these emissions.Metallurgical processes like sintering of iron ore, production of steel and non-ferrous and light metals from scrap material belong to a group of stationary PCDDs/Fs emitters and their share in the total PCDDs/Fs emission into the environment is very significant. The relative significance of particular metallurgical processes varies from country to country, depending on the nature of a particular process, installed capacities and annual output levels.As the modern approach to observing the environment includes preventive measures, as opposed to corrective post-event measures that were common practice in the past, the owners/operators of metallurgical processes are developing and introducing pollution monitoring and surveillance systems, based on which they take appropriate measures.One of the frequently applied measures is to build and implement the ISO 14001 environmental management system that very efficiently runs production processes along with maintenance of environmental protection on a daily basis. Since the adoption of the ISO 14001 environmental management system is a voluntary decision to be made by each organization, in 1996 the European Union adopted, for the purpose of environmental protection and pollution prevention, the Directive 96/61 EC or IPPC Directive on Integrated Pollution Prevention and Control (IPPC requiring from industrial installations, depending on their type and output level, to obtain environmental permits to run production processes using best available techniques, thus maintaining

40 CFR 63.1213 - How can the compliance date be extended to install pollution prevention or waste minimization...

Science.gov (United States)

2010-07-01

... to install pollution prevention or waste minimization controls? 63.1213 Section 63.1213 Protection of... pollution prevention or waste minimization controls? (a) Applicability. You may request from the... must contain the following information: (i) A description of pollution prevention or waste minimization...

Westinghouse Hanford Company waste minimization and pollution prevention awareness program plan

International Nuclear Information System (INIS)

Craig, P.A.; Nichols, D.H.; Lindsey, D.W.

1991-08-01

The purpose of this plan is to establish the Westinghouse Hanford Company's Waste Minimization Program. The plan specifies activities and methods that will be employed to reduce the quantity and toxicity of waste generated at Westinghouse Hanford Company (Westinghouse Hanford). It is designed to satisfy the US Department of Energy (DOE) and other legal requirements that are discussed in Subsection C of the section. The Pollution Prevention Awareness Program is included with the Waste Minimization Program as permitted by DOE Order 5400.1 (DOE 1988a). This plan is based on the Hanford Site Waste Minimization and Pollution Prevention Awareness Program Plan, which directs DOE Field Office, Richland contractors to develop and maintain a waste minimization program. This waste minimization program is an organized, comprehensive, and continual effort to systematically reduce waste generation. The Westinghouse Hanford Waste Minimization Program is designed to prevent or minimize pollutant releases to all environmental media from all aspects of Westinghouse Hanford operations and offers increased protection of public health and the environment. 14 refs., 2 figs., 1 tab

Integrated ultrasonic/microbiological treatment of toxic and refractory pollutants

Energy Technology Data Exchange (ETDEWEB)

Tiehm, A. [Water Technology Center, Karlsruhe (Germany)

2002-07-01

The elimination of environmental pollutants by biodegradation in many cases represents an efficient and reliable method, e.g. in waste waster treatment, treatment of solid wastes, and in the remediation of contaminated soil. Nevertheless, there are situations where biological treatment alone does not result in a successful elimination of the target pollutants. For example, the presence of toxic compounds, an insufficient period of adaptation or a low bioavailability of the pollutants hinder a rapid biodegradation. Physico-chemical techniques, e.g. sonochemical degradation, provide an alternative to eliminate pollutants that are poorly biodegradable. It is the aim of this paper to demonstrate the potential of integrated ultrasound/biodegradation processes in the light of the underlying mechanisms. Optimisation of sonication is discussed with respect to ultrasound frequency and pH of the aqueous phase. Examplarily, two successful combinations of the integrated process are presented: (i) Application of ultrasound to reduce the toxicity of chlorophenols and (ii) ultrasonic irradiation to increase mass transfer and biodegradation of polyaromatic hydrocarbons. (orig.)

Integrated monitoring and assessment of air pollution

Energy Technology Data Exchange (ETDEWEB)

Hertel, O.

2009-09-15

Improved quality, better understanding of processes and optimisation of allocated resources, these are the main advantages of applying Integrated Monitoring and Assessment (IMA) in air quality management. The IMA is defined as the combined use of measurements and model calculations. The use of IMA is demonstrated with examples with different aims: to obtain data for air pollution in urban streets, to assess human exposure to traffic air pollution, and to assess atmospheric deposition of nitrogen compounds to marine and terrestrial ecosystems. (author)

Oak Ridge K-25 Site chlorinated solvent pollution prevention opportunity assessment

Energy Technology Data Exchange (ETDEWEB)

1994-08-01

A pollution prevention opportunity assessment (PPOA) was conducted at the Oak Ridge K-25 Site to identify opportunities to reduce and better manage the use of chlorinated solvents. At the K-25 Site, 67 control areas were examined for their potential use of chlorinated solvents. Of these areas, 27 were found to be using (1) chlorinated solvents for cleaning, degreasing, and lubricating; (2) laboratory standards and solvents; and (3) test medium. Current management practices encourage the identification and use of nonhazardous chemicals, including the use of chlorinated solvents. The main pollution prevention principles are source reduction and recycling, and a number of pollution prevention options based on these principles were identified and evaluated as part of this chlorinated solvent PPOA. Source reduction options evaluated for the K-25 Site include the substitution of chlorinated solvents with nonchlorinated solvents. Recycling was identified for those areas that would benefit most from the reuse of the chlorinated solvents in use. The pollution prevention options that offer the greatest opportunity for success at the K-25 Site are the implementation of substitutes at the 10 control areas using chlorinated solvents for cleaning, degreasing, and lubrication. A change in the process may be all that is needed to eliminate the use of a chlorinated solvent. Once a decision is made to implement a substitution, the information should be communicated to all shops and laboratories. Another option to consider is the installation of recycling units to recycle the large amounts of methylene chloride used in the analytical sampling procedure.

Oak Ridge K-25 Site chlorinated solvent pollution prevention opportunity assessment

International Nuclear Information System (INIS)

1994-08-01

A pollution prevention opportunity assessment (PPOA) was conducted at the Oak Ridge K-25 Site to identify opportunities to reduce and better manage the use of chlorinated solvents. At the K-25 Site, 67 control areas were examined for their potential use of chlorinated solvents. Of these areas, 27 were found to be using (1) chlorinated solvents for cleaning, degreasing, and lubricating; (2) laboratory standards and solvents; and (3) test medium. Current management practices encourage the identification and use of nonhazardous chemicals, including the use of chlorinated solvents. The main pollution prevention principles are source reduction and recycling, and a number of pollution prevention options based on these principles were identified and evaluated as part of this chlorinated solvent PPOA. Source reduction options evaluated for the K-25 Site include the substitution of chlorinated solvents with nonchlorinated solvents. Recycling was identified for those areas that would benefit most from the reuse of the chlorinated solvents in use. The pollution prevention options that offer the greatest opportunity for success at the K-25 Site are the implementation of substitutes at the 10 control areas using chlorinated solvents for cleaning, degreasing, and lubrication. A change in the process may be all that is needed to eliminate the use of a chlorinated solvent. Once a decision is made to implement a substitution, the information should be communicated to all shops and laboratories. Another option to consider is the installation of recycling units to recycle the large amounts of methylene chloride used in the analytical sampling procedure

Directory of Pollution Prevention in Higher Education: Faculty and Programs 1992. Doc #93-2.

Science.gov (United States)

Bakshani, Nandkumar; Allen, David

This survey reports the current state of development of pollution prevention education in Universities in the United States based on a national survey conducted between December 1991 and February 1992. Over 140 individuals (from 80 institutions) believed to be active in pollution prevention education were contacted and of these 89 (from 59…

Pollution Prevention Opportunity Assessment for the SNL/NM cafeterias.

Energy Technology Data Exchange (ETDEWEB)

McCord, Samuel Adam

2005-12-01

This Pollution Prevention Opportunity Assessment (PPOA) was conducted for the two Sandia National Laboratories/New Mexico cafeteria facilities between May and August 2005. The primary purpose of this PPOA is to assess waste and resource reduction opportunities and issue Pollution Prevention (P2) recommendations for Sandia's food service facilities. This PPOA contains recommendations for energy, water and resource reduction, as well as material substitution based upon environmentally preferable purchasing. Division 3000 has requested the PPOA report as part of the Division's compliance effort to implement the Environmental Management System (EMS) per DOE Order 450.1. This report contains a summary of the information collected and analyses performed with recommended options for implementation. The SNL/NM P2 Group will work with Division 3000 and the respective cafeteria facilities to implement these options.

An Innovative Partnership Approach for Environmental Management and Pollution Prevention.

Science.gov (United States)

Erten-Unal, Mujde; Aydlett, Guy M.

1997-01-01

A partnership between a university and a government regulatory agency sought to assist industries with pollution prevention and waste management. Economic incentives were developed to promote waste minimization. (SK)

Integrative Medicine in Preventive Medicine Education

Science.gov (United States)

Jani, Asim A.; Trask, Jennifer; Ali, Ather

2016-01-01

During 2012, the USDHHS’s Health Resources and Services Administration funded 12 accredited preventive medicine residencies to incorporate an evidence-based integrative medicine curriculum into their training programs. It also funded a national coordinating center at the American College of Preventive Medicine, known as the Integrative Medicine in Preventive Medicine Education (IMPriME) Center, to provide technical assistance to the 12 grantees. To help with this task, the IMPriME Center established a multidisciplinary steering committee, versed in integrative medicine, whose primary aim was to develop integrative medicine core competencies for incorporation into preventive medicine graduate medical education training. The competency development process was informed by central integrative medicine definitions and principles, preventive medicine’s dual role in clinical and population-based prevention, and the burgeoning evidence base of integrative medicine. The steering committee considered an interdisciplinary integrative medicine contextual framework guided by several themes related to workforce development and population health. A list of nine competencies, mapped to the six general domains of competence approved by the Accreditation Council of Graduate Medical Education, was operationalized through an iterative exercise with the 12 grantees in a process that included mapping each site’s competency and curriculum products to the core competencies. The competencies, along with central curricular components informed by grantees’ work presented elsewhere in this supplement, are outlined as a roadmap for residency programs aiming to incorporate integrative medicine content into their curricula. This set of competencies adds to the larger efforts of the IMPriME initiative to facilitate and enhance further curriculum development and implementation by not only the current grantees but other stakeholders in graduate medical education around integrative medicine

An integrated approach to manage coastal ecosystems and prevent marine pollution effects

Science.gov (United States)

Marcelli, Marco; Bonamano, Simone; Carli, Filippo Maria; Giovacchini, Monica; Madonia, Alice; Mancini, Emanuele; Molino, Chiara; Piermattei, Viviana; Manfredi Frattarelli, Francesco

2016-04-01

This work focuses an integrated approach based on Sea-Use-Map (SUM), backed by a permanent monitoring system (C-CEMS-Civitavecchia Coastal Environmental Monitoring System). This tool supports the management of the marine coastal area, contributing substantially to ecosystem benefits evaluation and to minimize pollution impacts. Within the Blue Growth strategy, the protection of marine ecosystems is considered a priority for the sustainable growth of marine and maritime sectors. To face this issue, the European MSP and MSFD directives (2014/89/EU; 2008/56/EC) strongly promote the adoption of an ecosystem-based approach, paying particular attention to the support of monitoring networks that use L-TER (long-term ecological research) observations and integrate multi-disciplinary data sets. Although not largely used in Europe yet, the Environmental Sensitivity Index (ESI), developed in 1979 by NOAA (and promoted by IMO in 2010), can be considered an excellent example of ecosystem-based approach to reduce the environmental consequences of an oil spill event in a coastal area. SUM is an ecosystem oriented cartographic tool specifically designed to support the sustainable management of the coastal areas, such as the selection of the best sites for the introduction of new uses or the identification of the coastal areas subjected to potential impacts. It also enables a rapid evaluation of the benefits produced by marine areas as well as of their anthropogenic disturbance. SUM integrates C-CEMS dataset, geomorphological and ecological features and knowledge on the coastal and maritime space uses. The SUM appliance allowed to obtain relevant operational results in the Civitavecchia coastal area (Latium, Italy), characterized by high variability of marine and coastal environments, historical heritage and affected by the presence of a big harbour, relevant industrial infrastructures, and touristic features. In particular, the valuation of marine ecosystem services based on

Pollution prevention for cleaner air: EPA's air and energy engineering research laboratory

International Nuclear Information System (INIS)

Shaver, E.M.

1992-01-01

The article discusses the role of EPA's Air and Energy Engineering Research Laboratory (AEERL) in pollution prevention research for cleaner air. For more than 20 years, AEERL has been conducting research to identify control approaches for the pollutants and sources which contribute to air quality problems. The Laboratory has successfully developed and demonstrated cost-effective sulfur dioxide, nitrogen oxides, and particulate control technologies for fossil fuel combustion sources. More recently, it has expanded its research activities to include indoor air quality, radon, organic control, stratospheric ozone depletion, and global warming. AEERL also develops inventories of air emissions of many types. Over the last several years, it has made substantial efforts to expand research on pollution prevention as the preferred choice for air emissions reduction

Hanford Site Pollution Prevention Plan Progress report, 1993

Energy Technology Data Exchange (ETDEWEB)

1994-08-01

This report tracks progress against the goals stated in the Hanford Site 5-year Pollution Prevention Plan. The executive summary of the plan was submitted to the Washington State Department of Ecology (Ecology) in September 1992. The plan, executive summary, and the progress reports are elements of a pollution prevention planning program that is required by Washington Administrative Code (WAC) 173-307 for all hazardous substance users and/or all hazardous waste generators regulated by Ecology. These regulations implement Chapter 70.95C, Revised Code of Washington, an act relating to hazardous waste reduction. The act encourages voluntary efforts to redesign industrial processes to help reduce or eliminate hazardous substances and hazardous waste byproducts, and to maximize the inprocess reuse or reclamation of valuable spent material. Although the Hanford Site is exempt, it is voluntarily complying with this state regulatory-mandated program. This is the first year the Hanford Site is submitting a progress report. It covers calendar year 1993 plus the last quarter of 1992. What is reported, in accordance with WAC 173-307, are reductions in hazardous substance use and hazardous waste generated. A system of Process Waste Assessments (PWA) was chosen to meet the requirements of the program. The PWAs were organized by a physical facility or company organization. Each waste-generating facility/organization performed PWAs to identify, screen, and analyze their own reduction options. Each completed PWA identified any number of reduction opportunities, that are listed individually in the plan and summarized by category in the executive summary. These opportunities were to be implemented or evaluated further over the duration of the 5-year plan. The basis of this progress report is to track action taken on these PWA reduction opportunities in relationship to achieving the goals stated in the Pollution Prevention Plan.

Hanford Site Pollution Prevention Plan Progress report, 1993

International Nuclear Information System (INIS)

1994-08-01

This report tracks progress against the goals stated in the Hanford Site 5-year Pollution Prevention Plan. The executive summary of the plan was submitted to the Washington State Department of Ecology (Ecology) in September 1992. The plan, executive summary, and the progress reports are elements of a pollution prevention planning program that is required by Washington Administrative Code (WAC) 173-307 for all hazardous substance users and/or all hazardous waste generators regulated by Ecology. These regulations implement Chapter 70.95C, Revised Code of Washington, an act relating to hazardous waste reduction. The act encourages voluntary efforts to redesign industrial processes to help reduce or eliminate hazardous substances and hazardous waste byproducts, and to maximize the inprocess reuse or reclamation of valuable spent material. Although the Hanford Site is exempt, it is voluntarily complying with this state regulatory-mandated program. This is the first year the Hanford Site is submitting a progress report. It covers calendar year 1993 plus the last quarter of 1992. What is reported, in accordance with WAC 173-307, are reductions in hazardous substance use and hazardous waste generated. A system of Process Waste Assessments (PWA) was chosen to meet the requirements of the program. The PWAs were organized by a physical facility or company organization. Each waste-generating facility/organization performed PWAs to identify, screen, and analyze their own reduction options. Each completed PWA identified any number of reduction opportunities, that are listed individually in the plan and summarized by category in the executive summary. These opportunities were to be implemented or evaluated further over the duration of the 5-year plan. The basis of this progress report is to track action taken on these PWA reduction opportunities in relationship to achieving the goals stated in the Pollution Prevention Plan

ADDRESSING POLLUTION PREVENTION ISSUES IN THE DESIGN OF A NEW NUCLEAR RESEARCH FACILITY

International Nuclear Information System (INIS)

Cournoyer, Michael E.; Corpion, Juan; Nelson, Timothy O.

2003-01-01

The Chemistry and Metallurgical Research (CMR) Facility was designed in 1949 and built in 1952 at Los Alamos National Laboratory (LANL) to support analytical chemistry, metallurgical studies, and actinide research and development on samples of plutonium and other nuclear materials for the Atomic Energy Commission's nuclear weapons program. These primary programmatic uses of the CMR Facility have not changed significantly since it was constructed. In 1998, a seismic fault was found to the west of the CMR Facility and projected to extend beneath two wings of the building. As part of the overall Risk Management Strategy for the CMR Facility, the Department of Energy (DOE) proposed to replace it by 2010 with what is called the CMR Facility Replacement (CMRR). In an effort to make this proposed new nuclear research facility environmentally sustainable, several pollution prevention/waste minimization initiatives are being reviewed for potential incorporation during the design phase. A two-phase approach is being adopted; the facility is being designed in a manner that integrates pollution prevention efforts, and programmatic activities are being tailored to minimize waste. Processes and procedures that reduce waste generation compared to current, prevalent processes and procedures are identified. Some of these ''best practices'' include the following: (1) recycling opportunities for spent materials; (2) replacing lithium batteries with alternate current adaptors; (3) using launderable contamination barriers in Radiological Control Areas (RCAs); (4) substituting mercury thermometers and manometers in RCAs with mercury-free devices; (5) puncturing and recycling aerosol cans; (6) using non-hazardous low-mercury fluorescent bulbs where available; (7) characterizing low-level waste as it is being generated; and (8) utilizing lead alternatives for radiological shielding. Each of these pollution prevention initiatives are being assessed for their technical validity, relevancy

Pollution prevention opportunity assessment approach, training, and technical assistance for DOE contractors. FY 1995 report

Energy Technology Data Exchange (ETDEWEB)

Pemberton, S.

1996-02-01

The Department of Energy and its contractors are faced with environmental concerns and large waste management costs. Federal legislation and DOE Orders require sites to develop waste minimization/pollution prevention programs. In response to these requirements, the Kansas City Plant developed a pollution prevention tool called a pollution prevention opportunity assessment (PPOA). Pilot assessments resulted in the development of a graded approach to reduce the amount of effort required for activities that utilized nonhazardous and/or low-volume waste streams. The project`s objectives in FY95 were to validate DOE`s PPOA Graded Approach methodology, provide PPOA training and technical assistance to interested DOE personnel and DOE contractors, enhance the methodology with energy analysis and tools for environmental restoration activities, implement a DOE-wide PPOA database, and provide support to DOE EM-334 in the completion of a report which estimates the future potential for pollution prevention and waste minimization in the DOE complex.

Pollution prevention opportunity assessment approach, training, and technical assistance for DOE contractors. FY 1995 report

International Nuclear Information System (INIS)

Pemberton, S.

1996-02-01

The Department of Energy and its contractors are faced with environmental concerns and large waste management costs. Federal legislation and DOE Orders require sites to develop waste minimization/pollution prevention programs. In response to these requirements, the Kansas City Plant developed a pollution prevention tool called a pollution prevention opportunity assessment (PPOA). Pilot assessments resulted in the development of a graded approach to reduce the amount of effort required for activities that utilized nonhazardous and/or low-volume waste streams. The project's objectives in FY95 were to validate DOE's PPOA Graded Approach methodology, provide PPOA training and technical assistance to interested DOE personnel and DOE contractors, enhance the methodology with energy analysis and tools for environmental restoration activities, implement a DOE-wide PPOA database, and provide support to DOE EM-334 in the completion of a report which estimates the future potential for pollution prevention and waste minimization in the DOE complex

An Integrated Approach for Pollution Monitoring: Smart Acquirement and Smart Information

Science.gov (United States)

Arco, E.; Boccardo, P.; Gandino, F.; Lingua, A.; Noardo, F.; Rebaudengo, M.

2016-09-01

Air quality is a factor of primary importance for the quality of life. The increase of the pollutants percentage in the air can cause serious problems to the human and environmental health. For this reason it is essential to monitor its values to prevent the consequences of an excessive concentration, to reduce the pollution production or to avoid the contact with major pollutant concentration through the available tools. Some recently developed tools for the monitoring and sharing of the data in an effective system permit to manage the information in a smart way, in order to improve the knowledge of the problem and, consequently, to take preventing measures in favour of the urban air quality and human health. In this paper, the authors describe an innovative solution that implements geomatics sensors (GNSS) and pollutant measurement sensors to develop a low cost sensor for the acquisition of pollutants dynamic data using a mobile platform based on bicycles. The acquired data can be analysed to evaluate the local distribution of pollutant density and shared through web platforms that use standard protocols for an effective smart use.

AN INTEGRATED APPROACH FOR POLLUTION MONITORING: SMART ACQUIREMENT AND SMART INFORMATION

Directory of Open Access Journals (Sweden)

E. Arco

2016-09-01

Full Text Available Air quality is a factor of primary importance for the quality of life. The increase of the pollutants percentage in the air can cause serious problems to the human and environmental health. For this reason it is essential to monitor its values to prevent the consequences of an excessive concentration, to reduce the pollution production or to avoid the contact with major pollutant concentration through the available tools. Some recently developed tools for the monitoring and sharing of the data in an effective system permit to manage the information in a smart way, in order to improve the knowledge of the problem and, consequently, to take preventing measures in favour of the urban air quality and human health. In this paper, the authors describe an innovative solution that implements geomatics sensors (GNSS and pollutant measurement sensors to develop a low cost sensor for the acquisition of pollutants dynamic data using a mobile platform based on bicycles. The acquired data can be analysed to evaluate the local distribution of pollutant density and shared through web platforms that use standard protocols for an effective smart use.

Environmental Restoration Program pollution prevention performance measures for FY 1993 and 1994 remedial investigations

International Nuclear Information System (INIS)

1993-03-01

The Martin Marietta Energy Systems, Inc., Environmental Restoration (ER) Program adopted a Pollution Prevention Program in March 1991. The program's mission is to minimize waste and prevent pollution in remedial investigations (RI), feasibility studies (FS), decontamination and decommissioning (D ampersand D), and surveillance and maintenance (S ampersand M) site program activities. Mission success will result in volume and/or toxicity reduction of generated waste. Energy Systems is producing a fully developed a Numerical Scoring System (NSS) and actually scoring the generators of Investigation Derived Waste (IDW) at six ER sites: Oak Ridge National Laboratory (ORNL), the Oak Ridge Y-12 Plant, the Oak Ridge K-25 site, Paducah Gaseous Diffusion Plant (Paducah), and Portsmouth Uranium Enrichment Complex (Portsmouth). This report summarizes the findings of this initial numerical scoring evaluation and shows where improvements in the overall ER Pollution prevention program may be required. This report identifies a number of recommendations that, if implemented, would help to improve site-performance measures. The continued development of the NSS will support generators in maximizing their Pollution Prevention/Waste Minimization efforts. Further refinements of the NSS, as applicable suggest comments and/or recommendations for improvement

Educational understanding of pollution prevention in decontamination and decommissioning/environmental restoration activities

International Nuclear Information System (INIS)

Betsch, M.D.; Lewis, R.A.

1995-05-01

Demolishing outdated structures from the US Department of Energy Hanford Site in Washington, generates large quantities of waste which can be minimized. The Hanford cleanup is one of the world's largest and most complex environmental restoration efforts. Approximately 280 square miles of ground water and soil are contaminated; there are more than 80 surplus facilities, including nine shut-down nuclear reactors in various stages of decay; and there are 177 underground waste storage tanks containing highly radioactive waste. In all, 1,500 cleanup sites have been identified and the Environmental Restoration Contractor (ERC) is currently responsible for surveillance and maintenance of 170 structures. A two hour orientation training in pollution prevention was developed by the Westinghouse Hanford Company to provide all Decontamination and Decommissioning/Environmental Restoration (D ampersand D/ER) personnel with the knowledge to apply waste minimization principles during their cleanup activities. The ERC Team Pollution Prevention Workshop serves to communicate pollution prevention philosophies and influences the way D ampersand D/ER projects are conducted at the Hanford Site

POLLUTION PREVENTION OPPORTUNITY ASSESSMENT - GEOCHEMISTRY LABORATORY AT SANDIA NATIONAL LABORATORIES

Science.gov (United States)

These reports summarize pollution prevention opportunity assessments conducted jointly by EPA and DOE at the Geochemistry Laboratory and the Manufacturing and Fabrication Repair Laboratory at the Department of Energy's Sandia National Laboratories facility in Albuquerque, New Mex...

Labor and pollution prevention in Canada.

Science.gov (United States)

Bennett, Dave

2012-01-01

This article gives an account of Canadian Chemicals Policy over the past three decades, including the project for the "virtual elimination" of toxic chemicals and the federal government's Chemical Management Plan. The latter is what remained when the virtual elimination program achieved few results. The article then embarks on its central theme: explaining how the labor movement introduced the concept and the practice of Pollution Prevention (P2) to Canada, as well as its impact on legislation and policies over the use reduction of chemical pesticides. The Appendix is a glossary of terms and concepts used in the article.

Assessment of pollution prevention and control technology for plating operations

Science.gov (United States)

Chalmer, Paul D.; Sonntag, William A.; Cushnie, George C., Jr.

1995-01-01

The National Center for Manufacturing Sciences (NCMS) is sponsoring an on-going project to assess pollution prevention and control technology available to the plating industry and to make this information available to those who can benefit from it. Completed project activities include extensive surveys of the plating industry and vendors of technologies and an indepth literature review. The plating industry survey was performed in cooperation with the National Association of Metal Finishers. The contractor that conducted the surveys and prepared the project products was CAI Engineering. The initial products of the project were made available in April, 1994. These products include an extensive report that presents the results of the surveys and literature review and an electronic database. The project results are useful for all those associated with pollution prevention and control in the plating industry. The results show which treatment, recovery and bath maintenance technologies have been most successful for different plating processes and the costs for purchasing and operating these technologies. The project results also cover trends in chemical substitution, the identification of compliance-problem pollutants, sludge generation rates, off-site sludge recovery and disposal options, and many other pertinent topics.

Prosperity without pollution: The prevention strategy for industry and consumers

International Nuclear Information System (INIS)

Hirschhorn, J.S.; Oldenburg, K.V.

1990-01-01

Here is the first book to explain why only a preventative environmental strategy can work: because growing population, consumption and industrialization cripple current, rather haphazard, remedial efforts. This book shows how our society can make more with less, be more competitive and less polluting, while maintaining our standard of living by reducing and eventually eliminating the production of wastes and pollutants from industry, commerce, homes, farms, and institutions. This may seem far-fetched, but be prepared to discover in this book that there can be a middle ground between ecology and economy - and that you can help achieve it. You'll find data and examples that any person can use, from engineers in industry to office workers to activists. Every concerned citizen will also want to consider the authors' innovative suggestions for taxing wastes and using the proceeds to help companies and communities switch to new industrial processes. Also, you should evaluate their proposals to reburies meaningful waste and toxicity information on product labels, to make bans on chemicals and products a more credible and available corrective measure, and to secure permanent, high-level government support for pollution prevention

Westinghouse Hanford Company Pollution Prevention Program Implementation Plan

International Nuclear Information System (INIS)

Floyd, B.C.

1994-10-01

This plan documents Westinghouse Hanford Company's (WHC) Pollution Prevention (P2) (formerly Waste Minimization) program. The program includes WHC; BCS Richland, Inc. (BCSR); and ICF Kaiser Hanford Company (ICF KH). The plan specifies P2 program activities and schedules for implementing the Hanford Site Waste Minimization and Pollution Prevention Awareness (WMin/P2) Program Plan requirements (DOE 1994a). It is intended to satisfy the U.S. Department of Energy (DOE) and other legal requirements that are discussed in both the Hanford Site WMin/P2 plan and paragraph C of this plan. As such, the Pollution Prevention Awareness Program required by DOE Order 5400.1 (DOE 1988) is included in the WHC P2 program. WHC, BCSR, and ICF KH are committed to implementing an effective P2 program as identified in the Hanford Site WMin/P2 Plan. This plan provides specific information on how the WHC P2 program will develop and implement the goals, activities, and budget needed to accomplish this. The emphasis has been to provide detailed planning of the WHC P2 program activities over the next 3 years. The plan will guide the development and implementation of the program. The plan also provides background information on past program activities. Because the plan contains greater detail than in the past, activity scope and implementation schedules may change as new priorities are identified and new approaches are developed and realized. Some activities will be accelerated, others may be delayed; however, all of the general program elements identified in this plan and contractor requirements identified in the Site WMin/P2 plan will be developed and implemented during the next 3 years. This plan applies to all WHC, BCSR, and ICF KH organizations and subcontractors. It will be distributed to those with defined responsibilities in this plan; and the policy, goals, objectives, and strategy of the program will be communicated to all WHC, BCSR, and ICF KH employees

Integrative Medicine in Preventive Medicine Education

OpenAIRE

Jani, Asim A.; Trask, Jennifer; Ali, Ather

2015-01-01

During 2012, the USDHHS?s Health Resources and Services Administration funded 12 accredited preventive medicine residencies to incorporate an evidence-based integrative medicine curriculum into their training programs. It also funded a national coordinating center at the American College of Preventive Medicine, known as the Integrative Medicine in Preventive Medicine Education (IMPriME) Center, to provide technical assistance to the 12 grantees. To help with this task, the IMPriME Center esta...

POLLUTION PREVENTION CASE STUDIES: LOW-VOC/HAP WOOD FURNITURE COATINGS

Science.gov (United States)

This article provides a brief profile of the wood furniture industry, discusses pollution prevention activities typically implemented, describes the four low-VOC/HAP coating technologies studied. and summarizes one case study for each of the low-VOC/HAP coating yechnologies inves...

Method for screening prevention and control measures and technologies based on groundwater pollution intensity assessment

Energy Technology Data Exchange (ETDEWEB)

Li, Juan, E-mail: lijuan@craes.org.cn [College of Water Sciences, Beijing Normal University, Beijing 100875 (China); Chinese Research Academy of Environmental Sciences, Beijing 100012 (China); State Environmental Protection Key Laboratory of Simulation and Control of Groundwater Pollution, Beijing, 100012 (China); Yang, Yang [College of Environment, Beijing Normal University, Beijing 100875 (China); Chinese Research Academy of Environmental Sciences, Beijing 100012 (China); State Environmental Protection Key Laboratory of Simulation and Control of Groundwater Pollution, Beijing, 100012 (China); Huan, Huan; Li, Mingxiao [Chinese Research Academy of Environmental Sciences, Beijing 100012 (China); State Environmental Protection Key Laboratory of Simulation and Control of Groundwater Pollution, Beijing, 100012 (China); Xi, Beidou, E-mail: xibd413@yeah.net [Chinese Research Academy of Environmental Sciences, Beijing 100012 (China); State Environmental Protection Key Laboratory of Simulation and Control of Groundwater Pollution, Beijing, 100012 (China); Lanzhou Jiaotong University, Lanzhou 730070 (China); Lv, Ningqing [Chinese Research Academy of Environmental Sciences, Beijing 100012 (China); State Environmental Protection Key Laboratory of Simulation and Control of Groundwater Pollution, Beijing, 100012 (China); Wu, Yi [Guizhou Academy of Environmental Science and Designing, Guizhou 550000 (China); Xie, Yiwen, E-mail: qin3201@126.com [School of Chemical and Environmental Engineering, Dongguan University of Technology, Dongguan, 523808 (China); Li, Xiang; Yang, Jinjin [Chinese Research Academy of Environmental Sciences, Beijing 100012 (China); State Environmental Protection Key Laboratory of Simulation and Control of Groundwater Pollution, Beijing, 100012 (China)

2016-05-01

This paper presents a system for determining the evaluation and gradation indices of groundwater pollution intensity (GPI). Considering the characteristics of the vadose zone and pollution sources, the system decides which anti-seepage measures should be implemented at the contaminated site. The pollution sources hazards (PSH) and groundwater intrinsic vulnerability (GIV) are graded by the revised Nemerow Pollution Index and an improved DRTAS model, respectively. GPI is evaluated and graded by a double-sided multi-factor coupling model, which is constructed by the matrix method. The contaminated sites are categorized as prior, ordinary, or common sites. From the GPI results, we develop guiding principles for preventing and removing pollution sources, procedural interruption and remediation, and end treatment and monitoring. Thus, we can select appropriate prevention and control technologies (PCT). To screen the technological schemes and optimize the traditional analytical hierarchy process (AHP), we adopt the technique for order preference by the similarity to ideal solution (TOPSIS) method. Our GPI approach and PCT screening are applied to three types of pollution sites: the refuse dump of a rare earth mine development project (a potential pollution source), a chromium slag dump, and a landfill (existing pollution sources). These three sites are identified as ordinary, prior, and ordinary sites, respectively. The anti-seepage materials at the refuse dump should perform as effectively as a 1.5-m-thick clay bed. The chromium slag dump should be preferentially treated by soil flushing and in situ chemical remediation. The landfill should be treated by natural attenuation technology. The proposed PCT screening approach was compared with conventional screening methods results at the three sites and proved feasible and effective. The proposed method can provide technical support for the monitoring and management of groundwater pollution in China. - Highlights: • An

Method for screening prevention and control measures and technologies based on groundwater pollution intensity assessment

International Nuclear Information System (INIS)

Li, Juan; Yang, Yang; Huan, Huan; Li, Mingxiao; Xi, Beidou; Lv, Ningqing; Wu, Yi; Xie, Yiwen; Li, Xiang; Yang, Jinjin

2016-01-01

This paper presents a system for determining the evaluation and gradation indices of groundwater pollution intensity (GPI). Considering the characteristics of the vadose zone and pollution sources, the system decides which anti-seepage measures should be implemented at the contaminated site. The pollution sources hazards (PSH) and groundwater intrinsic vulnerability (GIV) are graded by the revised Nemerow Pollution Index and an improved DRTAS model, respectively. GPI is evaluated and graded by a double-sided multi-factor coupling model, which is constructed by the matrix method. The contaminated sites are categorized as prior, ordinary, or common sites. From the GPI results, we develop guiding principles for preventing and removing pollution sources, procedural interruption and remediation, and end treatment and monitoring. Thus, we can select appropriate prevention and control technologies (PCT). To screen the technological schemes and optimize the traditional analytical hierarchy process (AHP), we adopt the technique for order preference by the similarity to ideal solution (TOPSIS) method. Our GPI approach and PCT screening are applied to three types of pollution sites: the refuse dump of a rare earth mine development project (a potential pollution source), a chromium slag dump, and a landfill (existing pollution sources). These three sites are identified as ordinary, prior, and ordinary sites, respectively. The anti-seepage materials at the refuse dump should perform as effectively as a 1.5-m-thick clay bed. The chromium slag dump should be preferentially treated by soil flushing and in situ chemical remediation. The landfill should be treated by natural attenuation technology. The proposed PCT screening approach was compared with conventional screening methods results at the three sites and proved feasible and effective. The proposed method can provide technical support for the monitoring and management of groundwater pollution in China. - Highlights: • An

DOE pollution prevention in the 21st century

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-10-01

This document presents abstracts of the topics covered in the DOE Pollution Prevention in the 21st Century conference held July 9-11, 1996. These topics include: model facilities; Federal/NEPA/stake- holders; microchemistry; solvents and reduction; education and outreach; return on investments; energy management; decontamination and decommissioning; planning and regulations; environmental restoration; recycling; affirmative procurement in the executive branch; construction and demolition; materials exchange; and ISO 2000.

DOE pollution prevention in the 21st century

International Nuclear Information System (INIS)

1996-01-01

This document presents abstracts of the topics covered in the DOE Pollution Prevention in the 21st Century conference held July 9-11, 1996. These topics include: model facilities; Federal/NEPA/stake- holders; microchemistry; solvents and reduction; education and outreach; return on investments; energy management; decontamination and decommissioning; planning and regulations; environmental restoration; recycling; affirmative procurement in the executive branch; construction and demolition; materials exchange; and ISO 2000

Storm water pollution prevention plan for the Oak Ridge Y-12 Plant

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

The Environmental Protection Agency (EPA) published the final storm water regulation on November 16, 1990. The storm water regulation is included in the National Pollutant Discharge Elimination System (NPDES) regulations. An NPDES permit was issued for the Y-12 Plant on April 28, 1995, and was effective on July 1, 1995. The permit requires that a Storm Water Pollution Prevention Plan (SWP3) be developed by December 28, 1995, and be fully implemented by July 1, 1996; this plan has been developed to fulfill that requirement. The outfalls and monitoring points described in this plan contain storm water discharges associated with industrial activities as defined in the NPDES regulations. For storm water discharges associated with industrial activity, including storm water discharges associated with construction activity, that are not specifically monitored or limited in this permit, Y-12 Plant personnel will meet conditions of the General Storm Water Rule 1200-4-10. This document presents the programs and physical controls that are in place to achieve the following objectives: ensure compliance with Section 1200-4-10-.04(5) of the TDEC Water Quality Control Regulations and Part 4 of the Y-12 Plant NPDES Permit (TN0002968); provide operating personnel with guidance relevant to storm water pollution prevention and control requirements for their facility and/or project; and prevent or reduce pollutant discharge to the environment, in accordance with the Clean Water Act (CWA) and the Tennessee Water Quality Control Act.

Storm water pollution prevention plan for the Oak Ridge Y-12 Plant

International Nuclear Information System (INIS)

1995-09-01

The Environmental Protection Agency (EPA) published the final storm water regulation on November 16, 1990. The storm water regulation is included in the National Pollutant Discharge Elimination System (NPDES) regulations. An NPDES permit was issued for the Y-12 Plant on April 28, 1995, and was effective on July 1, 1995. The permit requires that a Storm Water Pollution Prevention Plan (SWP3) be developed by December 28, 1995, and be fully implemented by July 1, 1996; this plan has been developed to fulfill that requirement. The outfalls and monitoring points described in this plan contain storm water discharges associated with industrial activities as defined in the NPDES regulations. For storm water discharges associated with industrial activity, including storm water discharges associated with construction activity, that are not specifically monitored or limited in this permit, Y-12 Plant personnel will meet conditions of the General Storm Water Rule 1200-4-10. This document presents the programs and physical controls that are in place to achieve the following objectives: ensure compliance with Section 1200-4-10-.04(5) of the TDEC Water Quality Control Regulations and Part 4 of the Y-12 Plant NPDES Permit (TN0002968); provide operating personnel with guidance relevant to storm water pollution prevention and control requirements for their facility and/or project; and prevent or reduce pollutant discharge to the environment, in accordance with the Clean Water Act (CWA) and the Tennessee Water Quality Control Act

Pollution prevention opportunity assessments at Hanford

Energy Technology Data Exchange (ETDEWEB)

Betsch, M.D., Westinghouse Hanford

1996-06-26

The Pollution Prevention Opportunity Assessment (PPOA) is a pro- active way to look at a waste generating activity and identify opportunities to minimize wastes through a cost benefit analysis. Hanford`s PPOA process is based upon the graded approach developed by the Kansas City Plant. Hanford further streamlined the process while building in more flexibility for the individual users. One of the most challenging aspects for implementing the PPOA process at Hanford is one overall mission which is environmental restoration, Now that the facilities are no longer in production, each has a different non- routine activity making it difficult to quantify the inputs and outputs of the activity under consideration.

Hanford Site Pollution Prevention Plan progress report, 1994. Revision 1

International Nuclear Information System (INIS)

1995-09-01

This report tracks progress made during 1994 against the goals stated in DOE/RL-92-62, Executive Summary, Hanford Site Pollution Prevention Plan. The Executive Summary of the plan was submitted to the Washington State Department of Ecology (Ecology) in September 1992. The plan, Executive Summary, and the progress reports are elements of a pollution prevention planning program that is required by WAC 173-307, ''Plans,'' for all hazardous substance users and/or all hazardous waste generators regulated by Ecology. These regulations implement RCW 70.95C, ''Waste Reduction,'' an act relating to hazardous waste reduction. The act encourages voluntary efforts to redesign industrial processes to help reduce or eliminate hazardous substances and hazardous waste byproducts, and to maximize the in-process reuse or reclamation of valuable spent material. The Hanford Site is voluntarily complying with this state regulatory-mandated program. All treatment, storage, or disposal (TSD) facilities are exempt from participating; the Hanford Site is classified as a TSD

Waste minimization/pollution prevention study of high-priority waste streams

International Nuclear Information System (INIS)

Ogle, R.B.

1994-03-01

Although waste minimization has been practiced by the Metals and Ceramics (M ampersand C) Division in the past, the effort has not been uniform or formalized. To establish the groundwork for continuous improvement, the Division Director initiated a more formalized waste minimization and pollution prevention program. Formalization of the division's pollution prevention efforts in fiscal year (FY) 1993 was initiated by a more concerted effort to determine the status of waste generation from division activities. The goal for this effort was to reduce or minimize the wastes identified as having the greatest impact on human health, the environment, and costs. Two broad categories of division wastes were identified as solid/liquid wastes and those relating to energy use (primarily electricity and steam). This report presents information on the nonradioactive solid and liquid wastes generated by division activities. More specifically, the information presented was generated by teams of M ampersand C staff members empowered by the Division Director to study specific waste streams

Hanford Site Pollution Prevention Plan progress report, 1994. Revision 1

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

This report tracks progress made during 1994 against the goals stated in DOE/RL-92-62, Executive Summary, Hanford Site Pollution Prevention Plan. The Executive Summary of the plan was submitted to the Washington State Department of Ecology (Ecology) in September 1992. The plan, Executive Summary, and the progress reports are elements of a pollution prevention planning program that is required by WAC 173-307, ``Plans,`` for all hazardous substance users and/or all hazardous waste generators regulated by Ecology. These regulations implement RCW 70.95C, ``Waste Reduction,`` an act relating to hazardous waste reduction. The act encourages voluntary efforts to redesign industrial processes to help reduce or eliminate hazardous substances and hazardous waste byproducts, and to maximize the in-process reuse or reclamation of valuable spent material. The Hanford Site is voluntarily complying with this state regulatory-mandated program. All treatment, storage, or disposal (TSD) facilities are exempt from participating; the Hanford Site is classified as a TSD.

Integrated modelling of Priority Pollutants in stormwater systems

DEFF Research Database (Denmark)

Vezzaro, Luca; Ledin, Anna; Mikkelsen, Peter Steen

2012-01-01

The increasing focus on urban diffuse sources of Priority Pollutants (PPs) has highlighted stormwater as an important contributor to contamination of natural water bodies. This study presents an example of an integrated model developed to be able to quantify PP loads discharged by stormwater...

Evaluation of implementation an Integrated Safety and Preventive Maintenance System for Improving of Safety Indexes

Directory of Open Access Journals (Sweden)

I mohammadfam

2014-03-01

Full Text Available Accident analysis shows that one of the main reasons for accidents is non-integration of maintenance units with safety. Merging these two processes through an integrated system can reduce and or eliminate accidents, diseases, and environmental pollution. These issues lead to improvement in organizational performance, as well. The aim of this study is to design and establish an integrated system for obtaining the aforementioned goal. Integration was carried out at Nirou Moharreke Machine Tools Company via Structured System Analysis & Design Method (SSADM. In order to measure the effectiveness of the system, selected indexes were compared using statistical methods prior and after system establishment. Results show that the accident severity index reduced from 135.46 in 2010, to 43.85 in 2012. Moreover, system effectiveness improved equipment reliability and availability (e.g. reliability of the Pfeiffer Milling machine (P (t>50 increased from 0.89 in 2010, to 0.9 in 2012. This system by forecasting various failures, and planning and designing the required operations for preventing occurrence of these failures, plays an important role in improving safety conditions of equipment, and increasing organizational performance, and is capable of presenting an excellent accident prevention program.

Special issue review of pollution prevention management within the Department of Energy, final report

International Nuclear Information System (INIS)

1994-08-01

The Department of Energy's (DOE) national role and overall mission has been undergoing significant change. In the post-Cold War era, a new emphasis on cleaning up the wastes from the past has emerged. These changes provide both significant challenges as well as new opportunities for DOE. While the challenges may seem overwhelming as DOE realizes the magnitude of its environmental problems, its network of national laboratories and sites provide the resources to become a leader in environmental management through the development of new technologies and management practices. Because of the growing importance of pollution prevention in the United States and more specifically to DOE's environmental management strategy, the Office of Environmental Audit (EH-24) identified this as an area worthy of a Special Issue Review. A Special Issue Review is not an audit but rather an in-depth review of key environmental programs or activities which cut across organizational boundaries. The purpose of a Special Issue Review is to identify strengths and weaknesses of a program as well as significant crosscutting issues or challenges that are important to the future success of that program. The scope of the review included an assessment of pollution prevention program activities at Headquarters, selected operations offices, and selected sites offices and contractor organizations. All aspects of a pollution prevention program were considered including program strategy, infrastructure, management systems, and implementation practices. Also summarized are future pollution prevention challenges and recommendations

77 FR 62452 - Approval and Promulgation of Implementation Plans; State of Arizona; Prevention of Air Pollution...

Science.gov (United States)

2012-10-15

... Promulgation of Implementation Plans; State of Arizona; Prevention of Air Pollution Emergency Episodes AGENCY... (SIP) revision submitted by the State of Arizona to address the requirements regarding air pollution... air pollution emergency episodes in CAA section 110(a)(2)(G). Section 110(a)(2)(G) requires that each...

[Analysis and prevention of dust pollution caused by 5 common prosthetic materials].

Science.gov (United States)

Yang, Xiang-Wen; Wei, Bin; Zhu, Cao-Yun; Qian, Liang; Li, Yi-Han

2017-10-01

To analyze and evaluate dust pollution in prosthodontic clinic and make proposal for reasonable protection. This study analyzed the particle size, element composition and dust concentration of 5 materials which were commonly used in dental restorations (veneering ceramics, cobalt-chromium alloy, photosensitive plastic, hard base resin, advanced artificial teeth) by using scanning electron microscopy (SEM), X-ray energy dispersive spectrometer（EDS） and dust concentration laser tester, in order to assess the effects of prosthodontic dust posed on medical staff health and put forward reasonable suggestions for prevention and control of dust pollution. The particle size of veneering ceramics, cobalt-chromium alloy, photosensitive plastic, hard base resin and advanced artificial teeth was (2.15±3.00), (33.78±24.33), (7.78±11.86), (31.16±44.35) and (28.45±39.21)μm, respectively. The time weighted average respirable dust concentration of veneering ceramics was 0.393 mg/m 2 which was beyond the scope of national security. Dust pollution is serious in prosthodontic clinic to which we should pay more attention and take appropriate prevention measures.

A Study of Innovation: ERD Takes Pollution Prevention to a New Level

International Nuclear Information System (INIS)

Southmayd, A.

1999-01-01

ERD approaches its mission with a vision of continuously exceeding customer needs and expectations and continuously improving. It's this vision of continuous improvement that drives the ERD pollution prevention program towards innovation

Pollution prevention in the oil and soap industry: a case study

International Nuclear Information System (INIS)

Abou-Elela, S.I.; Zaher, F.

1998-01-01

Industrial audit of a complex oil and soap factory has been carried out. The factory produces edible oils, fatty acids, soap, crude, industrial and pharmaceutical glycerin, powdered detergents, animal fodder, sodium and potassium silicates, sodium hypochlorite and hypochloric acid. The audit shows that there were a wide range of pollution prevention opportunities which could be implemented with significant financial advantages for the factory as well as reducing environmental pollution. Cost benefits for the recommended environmental improvements have been estimated. Many of the improvements had short payback periods. (author)

Pollution prevention in the oil and soap industry: a case study

Energy Technology Data Exchange (ETDEWEB)

Abou-Elela, S.I. [National Research Center, Gizza (Egypt). Water Pollution Control Dept.; Zaher, F. [National Research Center, Gizza (Egypt). Fats and Oil Dept.

1998-12-31

Industrial audit of a complex oil and soap factory has been carried out. The factory produces edible oils, fatty acids, soap, crude, industrial and pharmaceutical glycerin, powdered detergents, animal fodder, sodium and potassium silicates, sodium hypochlorite and hypochloric acid. The audit shows that there were a wide range of pollution prevention opportunities which could be implemented with significant financial advantages for the factory as well as reducing environmental pollution. Cost benefits for the recommended environmental improvements have been estimated. Many of the improvements had short payback periods. (author)

Preliminary tests of an electrokinetic barrier to prevent heavy metal pollution of soils

International Nuclear Information System (INIS)

Lynch, R.J.; Muntoni, A.; Ruggeri, R.; Winfield, K.C.

2007-01-01

Sardinia has to deal with significant environmental problems related to heavy-metal contamination, mainly located at its abandoned mining districts. In particular, acid mine drainage management and groundwater pollution are typical problems associated with mining activities which constitute a serious threat to human health. To prevent contaminant spread over the adjacent environment, it is of great interest to consider using an electric field as a containment fence to counteract pollutant transport. In this application, contaminant transport due to a hydraulic gradient driving force is prevented by the combined effect of electro-osmosis and electro-migration. Although there are other alternative containment technologies, the electrokinetic fence offers many advantages, as it is easy to operate, there is a minimal exposure to the operating personnel and it is likely to be effective for a wide range of contaminants. In this work, both one-dimensional (1D) and two-dimensional (2D) tests have been carried out. In the 1D tests, the efficiency of an electrokinetic barrier to prevent cadmium from polluting an uncontaminated sample was investigated; soil pH, metal concentration and current intensity have been monitored; results indicate that the barrier can prevent or significantly reduce heavy-metal contamination from spreading against a hydraulic gradient of 7. In 2D tests, two rows of electrodes inserted in a horizontally flat soil tank were used to generate an electric field. It was found that an electric field of 125 V m -1 was sufficient to prevent significant copper incursion from a contaminant flow under a hydraulic gradient of 1.3

Role of marine pollutants in impairment of DNA integrity.

Digital Repository Service at National Institute of Oceanography (India)

Sarker, S.; Sarkar, A.

In this article, we present an overview on the role of marine pollutants in impairment of DNA integrity in marine gastropods exposed to xenobiotics released from various sources into the coastal ecosystem. We provide an insight into the impact...

Multi-media pollution prevention: A case study of a refinery

International Nuclear Information System (INIS)

Schmitt, R.E.; Podar, M.K.

1994-01-01

In late 1989, Amoco Corporation and the United States Environmental Protection Agency began a voluntary, joint project to study pollution prevention opportunities at an industrial facility. Amoco proposed use of its refinery at Yorktown, Virginia, to conduct a multi-media assessment of releases to the environment, then to develop and evaluate options to reduce these releases. A Workgroup composed of state, federal, and Amoco representatives provided oversight to the Project. Monthly Workgroup meetings provided Project oversight, a forum for presentations on different Project components, and an opportunity for informal discussion of different viewpoints about environmental management. The Workgroup identified four objectives for this study: (1) Inventory refinery releases to the environment to define their chemical type, quantity, source, and medium of release; (2) develop options to reduce selected releases identified, as well as rank and prioritize the options based on a variety of criteria and perspectives; (3) identify and evaluate factors as technical, legislative, regulatory, institutional, permitting, and economic, that impede or encourage pollution prevention; and (4) enhance participates' knowledge of refinery and regulatory systems

A Study of Innovation: ERD Takes Pollution Prevention to a New Level

Energy Technology Data Exchange (ETDEWEB)

Southmayd, A.

1999-01-20

ERD approaches its mission with a vision of continuously exceeding customer needs and expectations and continuously improving. It's this vision of continuous improvement that drives the ERD pollution prevention program towards innovation.

CONSTRUCTED WETLAND TECHNOLOGY TO PREVENT WATER RESOURCES POLLUTION

Directory of Open Access Journals (Sweden)

Zeki Gökalp

2016-07-01

Full Text Available Discharge of untreated waste waters into surface waters creates significant pollution in these resources. Wastewaters are most of the time discharged into seas, rivers and other water bodies without any treatments due to high treatment costs both in Turkey and throughout the world. Constructed wetlands, also called as natural treatment systems, are used as an alternative treatment system to conventional high-cost treatment systems because of their low construction, operation and maintenance costs, energy demands, easy operation and low sludge generation. Today, constructed wetland systems are largely used to treat domestic wastewaters, agricultural wastewaters, industrial wastewater and runoff waters and ultimately to prevent water pollution and to improve water quality of receiving water bodies. In present study, currently implemented practices in design, construction, operation and maintenance of constructed wetlands were assessed and potential mistakes made in different phases these systems were pointed out and possible solutions were proposed to overcome these problems.

Healing and Preventing Pain: Complementary and Integrative Approaches

Science.gov (United States)

... page please turn JavaScript on. Feature: Pain Management Healing and Preventing Pain, Complementary and Integrative Approaches Past ... Pain Management" Articles Putting A Pause In Pain / Healing and Preventing Pain Complementary and Integrative Approaches / Pain ...

Study on the relationship between the opening of environmental tax and the prevention and control of air pollution in China

Science.gov (United States)

Gao, Guilin; Wang, Tianyi

2018-03-01

This article systematically expounds the status quo and sources of air pollution, the experience of foreign environmental tax policy, the advantages and disadvantages of environmental taxes levied in our country through literature research, historical analysis and comparative analysis and put forward recommendations on tax policy of prevention and control of air pollution by combining with the specific national conditions in our country. As one of the basic means of national macro-control, the tax policy is the major countermeasure that cannot be ignored in the prevention and control of air pollution. Studying the tax policy of prevention and control of air pollution will help to effectively control air pollution, develop a green economy and recycle economy and achieve the goal of improving environmental quality.

Environmental Restoration Progam Waste Minimization and Pollution Prevention Awareness Program Plan

Energy Technology Data Exchange (ETDEWEB)

Grumski, J. T.; Swindle, D. W.; Bates, L. D.; DeLozier, M. F.P.; Frye, C. E.; Mitchell, M. E.

1991-09-30

In response to DOE Order 5400.1 this plan outlines the requirements for a Waste Minimization and Pollution Prevention Awareness Program for the Environmental Restoration (ER) Program at Martin Marietta Energy System, Inc. Statements of the national, Department of Energy, Energy Systems, and Energy Systems ER Program policies on waste minimization are included and reflect the attitudes of these organizations and their commitment to the waste minimization effort. Organizational responsibilities for the waste minimization effort are clearly defined and discussed, and the program objectives and goals are set forth. Waste assessment is addressed as being a key element in developing the waste generation baseline. There are discussions on the scope of ER-specific waste minimization techniques and approaches to employee awareness and training. There is also a discussion on the process for continual evaluation of the Waste Minimization Program. Appendixes present an implementation schedule for the Waste Minimization and Pollution Prevention Program, the program budget, an organization chart, and the ER waste minimization policy.

Environmental Restoration Progam Waste Minimization and Pollution Prevention Awareness Program Plan

International Nuclear Information System (INIS)

1991-01-01

In response to DOE Order 5400.1 this plan outlines the requirements for a Waste Minimization and Pollution Prevention Awareness Program for the Environmental Restoration (ER) Program at Martin Marietta Energy System, Inc. Statements of the national, Department of Energy, Energy Systems, and Energy Systems ER Program policies on waste minimization are included and reflect the attitudes of these organizations and their commitment to the waste minimization effort. Organizational responsibilities for the waste minimization effort are clearly defined and discussed, and the program objectives and goals are set forth. Waste assessment is addressed as being a key element in developing the waste generation baseline. There are discussions on the scope of ER-specific waste minimization techniques and approaches to employee awareness and training. There is also a discussion on the process for continual evaluation of the Waste Minimization Program. Appendixes present an implementation schedule for the Waste Minimization and Pollution Prevention Program, the program budget, an organization chart, and the ER waste minimization policy

Pollution prevention at a profit in the production of iron and steel

International Nuclear Information System (INIS)

Fine, H.A.; Molbug, J.; Gorsevski, V.; Briskin, J.; Worrell, E.; Price, L.; Martin, N.

1997-01-01

Many different processes and flow sheets exist for the production of iron and steel. These individual processes and process combinations consume differing amounts of energy and result in differing carbon dioxide emissions, greatly complicating evaluation of new, energy conserving technologies. Not only does a large array of competing energy saving technologies exist, but these technologies must be applied to this diverse set of production facilities. A methodology now under development for performing a multiple pathways analysis that characterizes both energy usage and carbon emissions is described in this article. This methodology can examine multiple options at each step in the process for the production of iron and steel, and the potential economic and pollution prevention opportunities that each may have. A first order estimate of the role of energy and materials conservation in returning historical investment is also provided, demonstrating past pollution prevention at a profit. Finally, a preliminary analysis of selected strategies for further prevention at a profit in the production of iron and steel is provided

DOE pollution prevention in the 21st century. Proceedings

Energy Technology Data Exchange (ETDEWEB)

1996-12-31

This CD-ROM contains the proceedings from the DOE Pollution Prevention in the 21st Century Conference XII held July 9-11, 1996. Topics included model facilities, federal and NEPA stakeholders, microchemistry, source 4 solvents and reduction, education and outreach planning, return on investment, energy management, decontamination and decommissioning, planning and regulations, environmental restoration, solid waste, recycling, affirmative procurement in the executive branch, construction and demolition, international and ISO 14000, and poster sessions.

DOE pollution prevention in the 21st century. Proceedings

International Nuclear Information System (INIS)

1996-01-01

This CD-ROM contains the proceedings from the DOE Pollution Prevention in the 21st Century Conference XII held July 9-11, 1996. Topics included model facilities, federal and NEPA stakeholders, microchemistry, source 4 solvents and reduction, education and outreach planning, return on investment, energy management, decontamination and decommissioning, planning and regulations, environmental restoration, solid waste, recycling, affirmative procurement in the executive branch, construction and demolition, international and ISO 14000, and poster sessions

Environmental Restoration Program pollution prevention performance measures for FY 1993 and 1994 remedial investigations: Generator training manual

International Nuclear Information System (INIS)

1993-03-01

This computer-based program is designed to help waste generators in the Environmental Restoration (ER) Program prevent pollution at the DOE Oak Ridge Field Office (DOE-OR) facilities in Oak Ridge, Paducah, and Portsmouth. The Numerical Scoring System (NSS) is an interactive system designed to maintain data on ER Program pollution prevention efforts and to measure the success of these efforts through the ER Program life cycle

Environmental Restoration Program pollution prevention performance measures for FY 1993 and 1994 remedial investigations: Management training manual

International Nuclear Information System (INIS)

1993-03-01

This computer-based program is designed to help waste generators in the Environmental Restoration (ER) Program prevent pollution at the DOE Oak Ridge Field Office (DOE-OR) facilities in Oak Ridge, Paducah, and Portsmouth. The Numerical Scoring System (NSS) is an interactive system designed to maintain data on ER Program pollution prevention efforts and to measure the success of these efforts through the ER Program life cycle

An integrated assessment of climate change, air pollution, and energy security policy

International Nuclear Information System (INIS)

Bollen, Johannes; Hers, Sebastiaan; Van der Zwaan, Bob

2010-01-01

This article presents an integrated assessment of climate change, air pollution, and energy security policy. Basis of our analysis is the MERGE model, designed to study the interaction between the global economy, energy use, and the impacts of climate change. For our purposes we expanded MERGE with expressions that quantify damages incurred to regional economies as a result of air pollution and lack of energy security. One of the main findings of our cost-benefit analysis is that energy security policy alone does not decrease the use of oil: global oil consumption is only delayed by several decades and oil reserves are still practically depleted before the end of the 21st century. If, on the other hand, energy security policy is integrated with optimal climate change and air pollution policy, the world's oil reserves will not be depleted, at least not before our modeling horizon well into the 22nd century: total cumulative demand for oil decreases by about 24%. More generally, we demonstrate that there are multiple other benefits of combining climate change, air pollution, and energy security policies and exploiting the possible synergies between them. These benefits can be large: for Europe the achievable CO 2 emission abatement and oil consumption reduction levels are significantly deeper for integrated policy than when a strategy is adopted in which one of the three policies is omitted. Integrated optimal energy policy can reduce the number of premature deaths from air pollution by about 14,000 annually in Europe and over 3 million per year globally, by lowering the chronic exposure to ambient particulate matter. Only the optimal strategy combining the three types of energy policy can constrain the global average atmospheric temperature increase to a limit of 3 C with respect to the pre-industrial level. (author)

Amoco-US Environmental Protection Agency, pollution prevention project, Yorktown, Virginia: Solid waste data

International Nuclear Information System (INIS)

Kizior, G.J.

1991-01-01

In late 1989 Amoco and the US Environmental Protection Agency initiated a joint project to review pollution prevention alternatives at Amoco Oil Company's Yorktown, Virginia, Refinery as a case study site. The report summarizes the solid waste emissions inventory, solids source identification, and the solid waste sampling program that was conducted at the Amoco Yorktown Refinery on September 25-27, 1990, in support of the Pollution Prevention Project. Major findings showed that the majority of solid waste generation occurs as end-of-pipe solids resulting from the treatment of wastewaters from the refinery sewer. Based on a regression analysis of the composition data for samples collected during this project, major upstream contributors to these solids appear to be soils. Solids from process units are also significant contributors

Pollution prevention at the Kansas City Division through process waste assessments

International Nuclear Information System (INIS)

Pemberton, S.E.; Gentile, C.C.

1992-01-01

Allied-Signal Inc., Kansas City Division (KCD) is committed to the hazardous waste minimization requirements set forth under RCRA as amended by the Pollution Prevention Act and DOE Order 5400.1. To assure compliance with these regulations, the KCD has developed a comprehensive Pollution Prevention Program which focuses on the elimination or minimization of all material releases to all environmental media. The ownership of waste minimization is given to all of the waste generators through Departmental Pollution Prevention Plans. These plans include tools to achieve the waste minimization goals. One of these tools is the process waste assessment (PWA). A PWA is a planned procedure with the objective of identifying opportunities and methods to reduce or eliminate waste. A material balance is performed around a specific process which qualifies and quantifies the materials entering and exiting the process. These materials are further defined to the hazardous component level. The exiting materials are separated into what goes into the product, sent to waste management, and what is released to the air (fugitive or point source). Next, opportunities are identified and evaluated for the ability to eliminate or minimize the waste streams exiting the process. Therefore, the PWA provides the basic tool for the creation of a comprehensive process baseline and identification of opportunities to eliminate/minimize the release of hazardous and non-hazardous wastes. This presentation will describe the status and activities of the program conceived to initiate PWAs at the Kansas City Division (KCD) of Allied-Signal Inc.. This program is organized through business units Which consist of manufacturing, quality, and engineering personnel from a specific product line. The departments that these business units represent are the generators of the major process waste at the KCD. Included in the update will be a brief overview of the lessons learned from the methodology development and

Transforming environmental permitting and compliance policies to promote pollution prevention: Removing barriers and providing incentives to foster technology innovation, economic productivity, and environmental protection. Final report

International Nuclear Information System (INIS)

Berg, D.R.; Kerr, R.L.; Fleischer, S.; Gorsen, M.; Harris, E.

1993-04-01

The Technology Innovation and Economics (TIE) Committee, a standing committee of EPA's National Advisory Council for Environmental Policy and Technology (NACEPT), has concluded that major changes are needed in federal and state permitting and compliance programs to encourage adoption of practical pollution prevention approaches to environmental protection. The Committee recommends seven major areas for improvement, including: (1) Redesigning permit procedures to encourage regulated facilities to expand multi-media and pollution prevention environmental improvement efforts; (2) Accelerating development and use of innovative pollution prevention technologies and techniques through special permitting and review procedures during RD ampersand D and commercialization phases; (3) Developing and expanding federal and state pollution prevention enforcement initiative; (4) Supporting state initiatives in pollution prevention facility planning; (5) Expanding pollution prevention-related training, educational and technology diffusion efforts to better reach managers in all sectors of the economy; (6) Altering personnel reward systems to encourage EPA staff to champion pollution prevention; (7) Expanding and publicizing the system of national awards honoring outstanding pollution prevention research, training and technology implementation

Physiological Integration Affects Expansion of an Amphibious Clonal Plant from Terrestrial to Cu-Polluted Aquatic Environments

Science.gov (United States)

Xu, Liang; Zhou, Zhen-Feng

2017-03-01

The effects of physiological integration on clonal plants growing in aquatic and terrestrial habitats have been extensively studied, but little is known about the role in the extension of amphibious clonal plants in the heterogeneous aquatic-terrestrial ecotones, especially when the water environments are polluted by heavy metals. Ramets of the amphibious clonal herb Alternanthera philoxeroides were rooted in unpolluted soil and polluted water at three concentrations of Cu. The extension of populations from unpolluted terrestrial to polluted aqueous environments mainly relied on stem elongation rather than production of new ramets. The absorbed Cu in the ramets growing in polluted water could be spread horizontally to other ramets in unpolluted soil via physiological integration and redistributed in different organs. The performances of ramets in both terrestrial and aquatic habitats were negatively correlated with Cu intensities in different organs of plants. It is concluded that physiological integration might lessen the fitness of connected ramets in heterogeneously polluted environments. The mechanical strength of the stems decreased with increasing Cu levels, especially in polluted water. We suggest that, except for direct toxicity to growth and expansion, heavy metal pollution might also increase the mechanical risk in breaking failure of plants.

Pollution prevention opportunity assessment for MicroFab and SiFab facilities at Sandia National Laboratories.

Energy Technology Data Exchange (ETDEWEB)

Gerard, Morgan Evan

2011-12-01

This Pollution Prevention Opportunity Assessment (PPOA) was conducted for the MicroFab and SiFab facilities at Sandia National Laboratories/New Mexico in Fiscal Year 2011. The primary purpose of this PPOA is to provide recommendations to assist organizations in reducing the generation of waste and improving the efficiency of their processes and procedures. This report contains a summary of the information collected, the analyses performed, and recommended options for implementation. The Sandia National Laboratories Environmental Management System (EMS) and Pollution Prevention (P2) staff will continue to work with the organizations to implement the recommendations.

Pollution Prevention through Peer Education: A Community Health Worker and Small and Home-Based Business Initiative on the Arizona-Sonora Border.

Science.gov (United States)

Ramírez, Denise Moreno; Ramírez-Andreotta, Mónica D; Vea, Lourdes; Estrella-Sánchez, Rocío; Wolf, Ann Marie A; Kilungo, Aminata; Spitz, Anna H; Betterton, Eric A

2015-09-09

Government-led pollution prevention programs tend to focus on large businesses due to their potential to pollute larger quantities, therefore leaving a gap in programs targeting small and home-based businesses. In light of this gap, we set out to determine if a voluntary, peer education approach led by female, Hispanic community health workers (promotoras) can influence small and home-based businesses to implement pollution prevention strategies on-site. This paper describes a partnership between promotoras from a non-profit organization and researchers from a university working together to reach these businesses in a predominately Hispanic area of Tucson, Arizona. From 2008 to 2011, the promotora-led pollution prevention program reached a total of 640 small and home-based businesses. Program activities include technical trainings for promotoras and businesses, generation of culturally and language appropriate educational materials, and face-to-face peer education via multiple on-site visits. To determine the overall effectiveness of the program, surveys were used to measure best practices implemented on-site, perceptions towards pollution prevention, and overall satisfaction with the industry-specific trainings. This paper demonstrates that promotoras can promote the implementation of pollution prevention best practices by Hispanic small and home-based businesses considered "hard-to-reach" by government-led programs.

Pollution Prevention through Peer Education: A Community Health Worker and Small and Home-Based Business Initiative on the Arizona-Sonora Border

Directory of Open Access Journals (Sweden)

Denise Moreno Ramírez

2015-09-01

Full Text Available Government-led pollution prevention programs tend to focus on large businesses due to their potential to pollute larger quantities, therefore leaving a gap in programs targeting small and home-based businesses. In light of this gap, we set out to determine if a voluntary, peer education approach led by female, Hispanic community health workers (promotoras can influence small and home-based businesses to implement pollution prevention strategies on-site. This paper describes a partnership between promotoras from a non-profit organization and researchers from a university working together to reach these businesses in a predominately Hispanic area of Tucson, Arizona. From 2008 to 2011, the promotora-led pollution prevention program reached a total of 640 small and home-based businesses. Program activities include technical trainings for promotoras and businesses, generation of culturally and language appropriate educational materials, and face-to-face peer education via multiple on-site visits. To determine the overall effectiveness of the program, surveys were used to measure best practices implemented on-site, perceptions towards pollution prevention, and overall satisfaction with the industry-specific trainings. This paper demonstrates that promotoras can promote the implementation of pollution prevention best practices by Hispanic small and home-based businesses considered “hard-to-reach” by government-led programs.

Pollution Prevention through Peer Education: A Community Health Worker and Small and Home-Based Business Initiative on the Arizona-Sonora Border

Science.gov (United States)

Moreno Ramírez, Denise; Ramírez-Andreotta, Mónica D.; Vea, Lourdes; Estrella-Sánchez, Rocío; Wolf, Ann Marie A.; Kilungo, Aminata; Spitz, Anna H.; Betterton, Eric A.

2015-01-01

Government-led pollution prevention programs tend to focus on large businesses due to their potential to pollute larger quantities, therefore leaving a gap in programs targeting small and home-based businesses. In light of this gap, we set out to determine if a voluntary, peer education approach led by female, Hispanic community health workers (promotoras) can influence small and home-based businesses to implement pollution prevention strategies on-site. This paper describes a partnership between promotoras from a non-profit organization and researchers from a university working together to reach these businesses in a predominately Hispanic area of Tucson, Arizona. From 2008 to 2011, the promotora-led pollution prevention program reached a total of 640 small and home-based businesses. Program activities include technical trainings for promotoras and businesses, generation of culturally and language appropriate educational materials, and face-to-face peer education via multiple on-site visits. To determine the overall effectiveness of the program, surveys were used to measure best practices implemented on-site, perceptions towards pollution prevention, and overall satisfaction with the industry-specific trainings. This paper demonstrates that promotoras can promote the implementation of pollution prevention best practices by Hispanic small and home-based businesses considered “hard-to-reach” by government-led programs. PMID:26371028

Waste minimization and pollution prevention technology transfer : the Airlie House Projects

International Nuclear Information System (INIS)

Gatrone, R.; McHenry, J.; Myron, H.; Thout, J. R.

1998-01-01

The Airlie House Pollution Prevention Technology Transfer Projects were a series of pilot projects developed for the US Department of Energy with the intention of transferring pollution prevention technology to the private sector. The concept was to develop small technology transfer initiatives in partnership with the private sector. Argonne National Laboratory developed three projects: the microscale chemistry in education project, the microscale cost benefit study project, and the Bethel New Life recycling trainee project. The two microscale chemistry projects focused on introducing microscale chemistry technologies to secondary and college education. These programs were inexpensive to develop and received excellent evaluations from participants and regulators. The Bethel New Life recycling trainee project provided training for two participants who helped identify recycling and source reduction opportunities in Argonne National Laboratory's solid waste stream. The pilot projects demonstrated that technology transfer initiatives can be developed and implemented with a small budget and within a short period of time. The essential components of the pilot projects were identifying target technologies that were already available, identifying target audiences, and focusing on achieving a limited but defined objective

Air pollution: Impact and prevention

OpenAIRE

SIERRA-VARGAS, MARTHA PATRICIA; TERAN, LUIS M

2012-01-01

ABSTRACT Air pollution is becoming a major health problem that affects millions of people worldwide. In support of this observation, the World Health Organization estimates that every year, 2.4 million people die because of the effects of air pollution on health. Mitigation strategies such as changes in diesel engine technology could result in fewer premature mortalities, as suggested by the US Environmental Protection Agency. This review: (i) discusses the impact of air pollution on respirat...

Method for Assessing the Integrated Risk of Soil Pollution in Industrial and Mining Gathering Areas

Science.gov (United States)

Guan, Yang; Shao, Chaofeng; Gu, Qingbao; Ju, Meiting; Zhang, Qian

2015-01-01

Industrial and mining activities are recognized as major sources of soil pollution. This study proposes an index system for evaluating the inherent risk level of polluting factories and introduces an integrated risk assessment method based on human health risk. As a case study, the health risk, polluting factories and integrated risks were analyzed in a typical industrial and mining gathering area in China, namely, Binhai New Area. The spatial distribution of the risk level was determined using a Geographic Information System. The results confirmed the following: (1) Human health risk in the study area is moderate to extreme, with heavy metals posing the greatest threat; (2) Polluting factories pose a moderate to extreme inherent risk in the study area. Such factories are concentrated in industrial and urban areas, but are irregularly distributed and also occupy agricultural land, showing a lack of proper planning and management; (3) The integrated risks of soil are moderate to high in the study area. PMID:26580644

Method for Assessing the Integrated Risk of Soil Pollution in Industrial and Mining Gathering Areas.

Science.gov (United States)

Guan, Yang; Shao, Chaofeng; Gu, Qingbao; Ju, Meiting; Zhang, Qian

2015-11-13

Industrial and mining activities are recognized as major sources of soil pollution. This study proposes an index system for evaluating the inherent risk level of polluting factories and introduces an integrated risk assessment method based on human health risk. As a case study, the health risk, polluting factories and integrated risks were analyzed in a typical industrial and mining gathering area in China, namely, Binhai New Area. The spatial distribution of the risk level was determined using a Geographic Information System. The results confirmed the following: (1) Human health risk in the study area is moderate to extreme, with heavy metals posing the greatest threat; (2) Polluting factories pose a moderate to extreme inherent risk in the study area. Such factories are concentrated in industrial and urban areas, but are irregularly distributed and also occupy agricultural land, showing a lack of proper planning and management; (3) The integrated risks of soil are moderate to high in the study area.

The air pollution: sources, effects, prevention

International Nuclear Information System (INIS)

Elichegaray, C.

2008-01-01

The author offers a detailed and illustrated panorama of the air pollution sources and effects. The study is realized at the individual scale with the indoor pollution and at a global scale with the consequences of the greenhouse effect gases. Added to classical pollutants, the book takes into account new pollutants (organic, nano particulates, biological) and the epidemiology. (A.L.B.)

Method for screening prevention and control measures and technologies based on groundwater pollution intensity assessment.

Science.gov (United States)

Li, Juan; Yang, Yang; Huan, Huan; Li, Mingxiao; Xi, Beidou; Lv, Ningqing; Wu, Yi; Xie, Yiwen; Li, Xiang; Yang, Jinjin

2016-05-01

This paper presents a system for determining the evaluation and gradation indices of groundwater pollution intensity (GPI). Considering the characteristics of the vadose zone and pollution sources, the system decides which anti-seepage measures should be implemented at the contaminated site. The pollution sources hazards (PSH) and groundwater intrinsic vulnerability (GIV) are graded by the revised Nemerow Pollution Index and an improved DRTAS model, respectively. GPI is evaluated and graded by a double-sided multi-factor coupling model, which is constructed by the matrix method. The contaminated sites are categorized as prior, ordinary, or common sites. From the GPI results, we develop guiding principles for preventing and removing pollution sources, procedural interruption and remediation, and end treatment and monitoring. Thus, we can select appropriate prevention and control technologies (PCT). To screen the technological schemes and optimize the traditional analytical hierarchy process (AHP), we adopt the technique for order preference by the similarity to ideal solution (TOPSIS) method. Our GPI approach and PCT screening are applied to three types of pollution sites: the refuse dump of a rare earth mine development project (a potential pollution source), a chromium slag dump, and a landfill (existing pollution sources). These three sites are identified as ordinary, prior, and ordinary sites, respectively. The anti-seepage materials at the refuse dump should perform as effectively as a 1.5-m-thick clay bed. The chromium slag dump should be preferentially treated by soil flushing and in situ chemical remediation. The landfill should be treated by natural attenuation technology. The proposed PCT screening approach was compared with conventional screening methods results at the three sites and proved feasible and effective. The proposed method can provide technical support for the monitoring and management of groundwater pollution in China. Copyright © 2015

POLLUTION PREVENTION OPPORTUNITY ASSESSMENT - MANUFACTURING AND FABRICATION REPAIR LABORATORY AT SANDIA NATIONAL LABORATORIES

Science.gov (United States)

These reports summarize pollution prevention opportunity assessments conducted jointly by EPA and DOE at the Geochemistry Laboratory and the Manufacturing and Fabrication Repair Laboratory at the Department of Energy's Sandia National Laboratories facility in Albuquerque, New Mex...

Stormwater Pollution Prevention Plan - TA-60 Asphalt Batch Plant

Energy Technology Data Exchange (ETDEWEB)

Sandoval, Leonard Frank [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2018-01-31

This Storm Water Pollution Prevention Plan (SWPPP) was developed in accordance with the provisions of the Clean Water Act (33 U.S.C. §§1251 et seq., as amended), and the Multi-Sector General Permit for Storm Water Discharges Associated with Industrial Activity (U.S. EPA, June 2015) issued by the U.S. Environmental Protection Agency (EPA) for the National Pollutant Discharge Elimination System (NPDES) and using the industry specific permit requirements for Sector P-Land Transportation and Warehousing as a guide. This SWPPP applies to discharges of stormwater from the operational areas of the TA-60-01 Asphalt Batch Plant at Los Alamos National Laboratory. Los Alamos National Laboratory (also referred to as LANL or the “Laboratory”) is owned by the Department of Energy (DOE), and is operated by Los Alamos National Security, LLC (LANS). Throughout this document, the term “facility” refers to the TA-60 Asphalt Batch Plant and associated areas. The current permit expires at midnight on June 4, 2020.

Stormwater Pollution Prevention Plan - TA-60 Material Recycling Facility

Energy Technology Data Exchange (ETDEWEB)

Sandoval, Leonard Frank [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2018-01-31

This Storm Water Pollution Prevention Plan (SWPPP) was developed in accordance with the provisions of the Clean Water Act (33 U.S.C. §§1251 et seq., as amended), and the Multi-Sector General Permit for Storm Water Discharges Associated with Industrial Activity (U.S. EPA, June 2015) issued by the U.S. Environmental Protection Agency (EPA) for the National Pollutant Discharge Elimination System (NPDES) and using the industry specific permit requirements for Sector P-Land Transportation and Warehousing as a guide. This SWPPP applies to discharges of stormwater from the operational areas of the TA- 60 Material Recycling Facility at Los Alamos National Laboratory. Los Alamos National Laboratory (also referred to as LANL or the “Laboratory”) is owned by the Department of Energy (DOE), and is operated by Los Alamos National Security, LLC (LANS). Throughout this document, the term “facility” refers to the TA-60 Material Recycling Facility. The current permit expires at midnight on June 4, 2020.

Stormwater Pollution Prevention Plan TA-60 Asphalt Batch Plant Revision 2: January 2017

Energy Technology Data Exchange (ETDEWEB)

Sandoval, Leonard Frank [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-02-01

The Stormwater Pollution Prevention Team (PPT) is applicable to operations at the Technical Area (TA)- 60 Asphalt Batch Plant (ABP) located on Eniwetok Drive/Sigma Mesa, in Los Alamos County, New Mexico at Los Alamos National Laboratory (LANL).

Annual report of waste generation and pollution prevention progress 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

This seventh Annual Report presents and analyzes DOE Complex-wide waste generation and pollution prevention activities at 45 reporting sites from 1993 through 1998. This section summarizes Calendar Year 1998 Complex-wide waste generation and pollution prevention accomplishments. More detailed information follows this section in the body of the Report. In May 1996, the Secretary of Energy established a 50 percent Complex-Wide Waste Reduction Goal (relative to the 1993 baseline) for routine operations radioactive, mixed, and hazardous waste generation, to be achieved by December31, 1999. DOE has achieved its Complex-Wide Waste Reduction Goals for routine operations based upon a comparison of 1998 waste generation to the 1993 baseline. Excluding sanitary waste, routine operations waste generation decreased 67 percent overall from 1993 to 1998. However, for the first time since 1994, the total amount of materials recycled by the Complex decreased from 109,600 metric tons in 1997 to 92,800 metric tons in 1998. This decrease is attributed to the fact that in 1997, several large ''one-time only'' recycling projects were conducted throughout the Complex. In order to demonstrate commitment to DOE's Complex-wide recycling goal, it is important for sites to identify all potential large-scale recycling/reuse opportunities.

Air Pollution and Allergic Airway Diseases: Social Determinantsand Sustainability in the Control and Prevention.

Science.gov (United States)

Paramesh, H

2018-04-01

Air pollution, global warming and climate change are the major contributing factors in causing the increase prevalence of allergic airway diseases like asthma and allergic rhinitis and they will be the defining issues for health system in the twenty-first century. Asthma is an early onset non-communicable environmental disease with global epidemic and contributes a greatest psycho socio economic burden. Nearly 8 million global deaths are from air pollution. Over one billion population are the sufferers during 2015 and will increase to 4 billion by 2050. Air pollution not only triggers the asthma episodes but also changes the genetic pattern in initiating the disease process. Over the years our concept of management of allergic airway disease has changed from control of symptoms to prevention of the disease. To achieve this we need positive development on clean air policies with standard norms, tracking progress, monitoring and evaluation, partnership and conventions with local and global authorities. We do have challenges to overcome like rapid urbanization, lack of multisectorial policy making, lack of finance for research and development and lack of monitoring exposure to health burden from air pollution. We need to prioritize our strategy by sustainable, safe, human settlement, cities, sustainable energy, industrialization, and research. The measures to be adopted are highlighted in this review article. With effective measures by all stake holders we can reduce air pollution and prevent the global warming by 2030, along with 194 countries as adopted by WHO in May 2015.

Annual report of waste generation and pollution prevention progress 1995

International Nuclear Information System (INIS)

1997-02-01

This fourth Annual Report presents and analyzes 1995 DOE complex-wide waste generation and pollution prevention activities at 40 reporting sites in 25 States, and trends DOE waste generation from 1991 through 1995. DOE has established a 50% reduction goal (relative to the 1993 baseline) for routine operations radioactive and hazardous waste generation, due by December 31, 1999. Routine operations waste generation decreased 37% from 1994 to 1995, and 43% overall from 1993--1995

An environmental assessment strategy for the identification of pollution prevention opportunities in the southern Urals Region of Russia

International Nuclear Information System (INIS)

Gonzalez, M.A.; Ott, R.L.

1993-01-01

The serious environmental problems of the South Urals Region of Russia have been broadly described in a report coauthored by Russian weapons scientists. The importance of taking the first steps to prevent further environmental damage and adverse public health effects has been recognized by the international scientific community. Scientists at the Lawrence Livermore National Laboratory have initiated a project to assist the Russians in their pollution prevention efforts. The specific objectives of this project are to: (1) conduct a pragmatic survey of the industrial and governmental pollution sources in a limited geographic region of the South Urals and (2) identify the priorities for pollution prevention and for food and water supply improvements at distribution points. The emphasis is on preventing adverse impacts to human health and improving industrial productivity. This project focuses on immediate pollution problems resulting from current operations and their solutions, not on long-term research related to the large-scale cleanup of legacy wastes. The project emphasizes near-term cost effective solutions to prevent pollution while longer term research aimed at contamination from past practices is pursued by other scientists. The project is being conducted in collaboration with environmental and physical scientists from institutes associated with the Ural Branch of the Russian Academy of Sciences; government officials at the national, regional, and local levels; and non-governmental Russian environmental groups. A broad cross section of Russian technical, political, and environmental abilities and interests is mandatory. This cross section will ensure the technical quality, the political acceptability, and the popular credibility of the project results to the affected Russians in the South Urals. Progress on this project is presented in this paper

Prevention, Minimization and Control of Environmental Pollution at Mexico Sugar Mill

Directory of Open Access Journals (Sweden)

Dominguez-Manjarrez Candi Ashanti

2014-10-01

Full Text Available This research paper aims to recommend control measures directed towards preventing and minimizing pollution, looking forward to the improvement of the environmental management on the sugar industry in Mexico. This issue has been put on hold due to the necessity to address the economic, social and technological issues affecting it over time. In order to better understand the productive process and the actual problem that the industry is facing, while proposing effective and possible actions for improvement, a sugar mill type was selected as a case of study. A comprehensive assessment of the production process for the standard sugar was made, considering the activities in the field and at the mill. The proposed measures in the sugar mill allowed savings in consumption of ground water average 3,620 cubic meters per day, during the period of study, reduction in solid waste generated average 325 kilograms per day by implementing a waste separation program, and reducing atmospheric emissions of particles acting as fuel for a boiler operated with bagasse. The prevention, minimization and pollution control measures proposed can be applied to other mills in the country with the appropriate adaptations.

The U.S. DOE new production reactor/heavy water reactor facility pollution prevention/waste minimization program

International Nuclear Information System (INIS)

Kaczmarsky, Myron M.; Tsang, Irving; Stepien, Walter P.

1992-01-01

A Pollution Prevention/Waste Minimization Program was established during the early design phase of the U.S. DOE's New Production Reactor/Heavy Water Reactor Facility (NPR/HWRF) to encompass design, construction, operation and decommissioning. The primary emphasis of the program was given to waste elimination, source reduction and/or recycling to minimize the quantity and toxicity of material before it enters the waste stream for treatment or disposal. The paper discusses the regulatory and programmatic background as it applies to the NPR/HWRF and the waste assessment program developed as a phased approach to pollution prevention/waste minimization for the NPR/HWRF. Implementation of the program will be based on various factors including life cycle cost analysis, which will include costs associated with personnel, record keeping, transportation, pollution control equipment, treatment, storage, disposal, liability, compliance and oversight. (author)

Environmental engineering and pollution prevention. European network of excellence and partnership

International Nuclear Information System (INIS)

Wotte, J.; Halang, W.A.; Kraemer, B.J.

1996-01-01

The primary purpose of the workshop was to present and discuss the main goals, contents, projects, partners, and implications of a proposed non-profit European Research Network, which aims at establishing research nodes at key locations in European NATO and CP countries. All projects are directed to solutions for the heavily polluted 'Black Triangle' Bohemia, Saxony, and Silesia, which was selected as a nucleus for the network because of its geographical location and cross-border environmental problems. Papers are presented under the following subject headings: disarmament; environment; human resources; high technology; and health. They include papers on soil remediation at manufactured gas plants, and power generation in the Czech Republic and its contribution to air pollution prevention in Central Europe

[Pollution prevention and control of aqueous extract of astragali radix processed with ZrO2 inorganic ceramic membrane micro-filtration].

Science.gov (United States)

Pan, Lin-Men; Huang, Min-Yan; Guo, Li-Wei

2012-11-01

To study the measures for preventing and controlling the pollution of aqueous extract of Astragali Radix proceeded with inorganic ceramic membrane micro-filtration, in order to find effective measures for preventing and controlling the membrane pollution. The resistance distribution, polymer removal and changes in physical and chemical parameters of the zirconium oxide film of different pore diameters were determined to analyze the state or location of pollutants as well as the regularity of formation. Meanwhile, recoil and ultrasonic physical measures were adopted to strengthen the membrane process, in order to explore the methods for preventing and controlling the membrane pollution. When 0.2 microm of ZrO2 micro-filtrated aqueous extract of Astragali Radix, the rate of pollution was as high as 44.9%. The hole blocking resistance and the concentration polarization resistance were the main filtration resistances, while the surface deposit resistance decreased with the increase in the membrane's hold diameter; after micro-filtration, the liquid turbidity significantly reduced, with slight changes in both pH and viscosity. The 0.2 microm ZrO2 micro-filtration membrane performed better than the 0.05 microm pore size membrane in terms of conductivity. The 0. 2 microm and 0.05 microm pore diameter membranes showed better performance in the removal of pectin. The ultrasonic measure to strengthen membranes is more suitable to this system, with a flux rate up by 41.7%. The membrane optimization process adopts appropriate measures for preventing and controlling the membrane pollution, in order to reduce the membrane pollution, recover membrane performance and increase filtration efficiency.

Strategy for Meeting the Secretary of Energy and Hanford Site FY 2001 Pollution Prevention Goals

International Nuclear Information System (INIS)

CLARK, D.E.

2000-01-01

The purpose of this strategy is to identify the Fiscal Year (FY) 2001 Hanford Site waste reduction, sanitary recycling and affirmative procurement goals and identify the action required to ensure that the Secretary of Energy's FY 2005 pollution prevention and the FY 2001 Hanford Site goals are met. The strategy and plan to ensure that the Secretary of Energy's routine waste reduction, recycling, cleanup/stabilization waste and affirmative procurement goals are met consists of four phases. The first phase is to ensure that the infrastructure is in place to support planning and organization. This phase involves ensuring that roles and responsibilities are identified; requirement documents are current; goals and successes are communicated; and accurate and current waste information is available. Roles and responsibilities are identified and the RL requirement documents (i.e., the Hanford Site Waste Minimization and Pollution Prevention Awareness Program Plan and Hanford Site Guide for Preparing and Maintaining Generator Group Pollution Prevention Program Documentation) will specify the Secretary of Energy's goals. Goals will be communicated formally and informally via the Hanford Reach, training sessions, meetings and correspondence. Sharing of pollution prevention successes and goal progress are encouraged at the Pollution Prevention/Waste Minimization (PZ/WMin) quarterly meetings. Existing site waste generation databases will be utilized to provide current waste generation data. The second phase of the strategy and plan is to establish and allocate goals by prime contractor (i.e. Fluor Hanford, Inc. (FH), Pacific Northwest National Laboratory (PNNL), Bechtel Hanford Inc. (BHI), and CH2MHill Hanford Group (CHG)). This requires determining current status toward meeting the Secretary of Energy's goals; establishing the Hanford Site FY goals, and allocating waste reduction goals by prime contractor. The third phase of the strategy and plan is goal implementation. This

DEVELOPMENT OF AN INTEGRATED AIR POLLUTION MAPS ON KEY PLOT OF KRASNOYARSK REGION

Directory of Open Access Journals (Sweden)

E. A. Bozhilina

2016-01-01

Full Text Available The paper suggested the construction of a comprehensive air pollution map as an example of the key area of the Krasnoyarsk Territory. To create a map developed an original technique for limiting emissions spread zones in the atmosphere from industrial plants near the cities on the basis of climatic data. The proposed method is based on taking into account the repeatability wind speed and direction and length of time of pollutants in the atmosphere. The used methods of cartographic representation – quantitative background (emissions per unit area within the zones of the potential spread of contaminants, localized diagrams (emissions and air pollution index for the city, contour lines (the value of air pollution potential. Using an integrated map allows you to specify the impact of the transfer of pollutants in the formation of the level of pollution in the city, together with the volumes and values of emissions of air pollution potential.

[The development of an integrated suicide-violence prevention program for adolescents].

Science.gov (United States)

Park, Hyun Sook

2008-08-01

The purpose of this study was to develop an integrated suicide-violence prevention program for adolescents. Another purpose was to evaluate the effects of the integrated suicide-violence prevention program on self-esteem, parent-child communication, aggression, and suicidal ideation in adolescents. The study employed a quasi-experimental design. Participants for the study were high school students, 24 in the experimental group and 25 in the control group. Data was analyzed by using the SPSS/WIN. 11.5 program with chi2 test, t-test, and 2-way ANOVA. Participants in the integrated suicide-violence prevention program reported increased self-esteem scores, which was significantly different from those in the control group. Participants in the integrated suicide-violence prevention program reported decreased aggression and suicidal ideation scores, which was significantly different from those in the control group. The integrated suicide-violence prevention program was effective in improving self-esteem and decreasing aggression and suicidal ideation for adolescents. Therefore, this approach is recommended as the integrated suicide-violence prevention strategy for adolescents.

Theoretical integration and the psychology of sport injury prevention.

Science.gov (United States)

Chan, Derwin King-Chung; Hagger, Martin S

2012-09-01

Integrating different theories of motivation to facilitate or predict behaviour change has received an increasing amount of attention within the health, sport and exercise science literature. A recent review article in Sports Medicine, by Keats, Emery and Finch presented an integrated model using two prominent theories in social psychology, self-determination theory (SDT) and the theory of planned behaviour (TPB), aimed at explaining and enhancing athletes' adherence to sport injury prevention. While echoing their optimistic views about the utility of these two theories to explain adherence in this area and the virtues of theoretical integration, we would like to seize this opportunity to clarify several conceptual principles arising from the authors' integration of the theories. Clarifying the theoretical assumptions and explaining precisely how theoretical integration works is crucial not only for improving the comprehensiveness of the integrated framework for predicting injury prevention behaviour, but also to aid the design of effective intervention strategies targeting behavioural adherence. In this article, we use the integration of SDT and TPB as an example to demonstrate how theoretical integration can advance the understanding of injury prevention behaviour in sport.

Amoco/Environmental Protection Agency Pollution Prevention Project, Yorktown refinery. Refinery release inventory. Final report

International Nuclear Information System (INIS)

Klee, H.; Kizier, G.J.; Baloo, S.; Hockman, E.L.; Couzens-Roberts, C.

1992-07-01

The report volume summarizes physical data obtained during a 2-year pollution prevention study of Amoco Oil Company's Yorktown Virginia Refinery. The study was jointly sponsored as a cooperative effort of Amoco Corporation and the United States Environmental Protection Agency. A multi-media sampling program was used to identify potential pollution sources within the Refinery. Sampling and analysis included air, surface water, groundwater, and solid waste data. Public perceptions about environmental issues of concern in the vicinity of the Refinery were also surveyed. The inventory showed that nearly 99 percent of the releases were airborne at the facility. Most of the remainder involved land disposal of solid wastes. Specific sources of major pollutants are identified

Integral biostimulation of soil polluted by 60000 ppm of motor waste oil

Directory of Open Access Journals (Sweden)

Saucedo-Martínez Blanca Celeste

2017-08-01

Full Text Available Waste motor oil (WMO is a mixture of hydrocarbons (HICO soil pollutants. An alternative solution for its elimination is the biostimulation (BIS, secuancial, complementary and accumulative or integral which requires at first BIS by detergents to emulsify WMO, the second one following by enrichment by mineral solution, H2O2 as a O2 source for oxidation of WMO and controlling moisture soil content at 80% field capacity for exchange gases in soil to stimulate WMO mineralization The aim of the work was: i analyze in the integral BIS of contaminated soil by 60000 ppm of WMO. The first BIS was applying detergents to emulsify the WMO, the second BIS by mineral solution, then by H2O2, under humidity control at 80% of field capacity, for the best oxidation of WMO. Additionally bacterial population oxidant WMO was meas-ured, to select those which synthetized detergent related to WMO degradation, finally the type of bacteria were molecular identify. Results showed than integral BIS by an anionic / nonionic detergent, then en-richment with mineral solution, and 0.5% H2O2, reduced WMO from 60000 ppm to 27200 ppm in 23 days. Density of bacterial WMO oxidant population was 268 X 106 CFU/g dry soil, from which the domi-nant ones were selected and identified 47 bacterial genera divided into: Actinomycetes, Firmicutes and Proteobacteria. These results showed that soil pollution by high concentration level of WMO demanded at integrated BIS, also was found some bacterial genus which synthetized detergent with potential used in soil polluted by WMO.

Integrated effects of air pollution and climate change on forests: a northern hemisphere perspective.

Science.gov (United States)

Bytnerowicz, Andrzej; Omasa, Kenji; Paoletti, Elena

2007-06-01

Many air pollutants and greenhouse gases have common sources, contribute to radiative balance, interact in the atmosphere, and affect ecosystems. The impacts on forest ecosystems have been traditionally treated separately for air pollution and climate change. However, the combined effects may significantly differ from a sum of separate effects. We review the links between air pollution and climate change and their interactive effects on northern hemisphere forests. A simultaneous addressing of the air pollution and climate change effects on forests may result in more effective research, management and monitoring as well as better integration of local, national and global environmental policies.

D and D TECHNOLOGIES FOR POLLUTION PREVENTION

International Nuclear Information System (INIS)

Tripp, Julia L.

2003-01-01

A new Accelerated Site Technology Deployment (ASTD) project was awarded in FY 2002 to the Idaho National Engineering and Environmental Laboratory (INEEL) to deploy technologies that decrease pollution and waste in the areas of facility characterization, sludge treatment, dust and contamination control, and concrete demolition. This project was called ''D and D Technologies for Pollution Prevention'' and planned to deploy four different technologies. To reduce protective equipment requirements, waste generation, and risk of radiation exposure during facility characterization, the Russian Gamma Locater Device (GLD) and Isotopic Identification Device (IID) for remote characterization was investigated. The GLD detects gamma ray readings and video images remotely and uses radio communication to transmit the readings to personnel located a safe distance from the contaminated area. The IID, an integral part of the GLD, provides real-time spectrometric analysis of radiation sources for remotely identifying the specific radioactive isotopes present in the facility. At the INEEL, sludge has accumulated in the bottom of a fuel storage pool and the presence of heavy metals in the sludge makes it a mixed waste. This project planned to use LEADX(reg s ign) to treat sludge in place to effectively make all heavy metals in the sludge insoluble. LEADX(reg s ign) is a dry granular chemical additive (apatite) used for in-situ treatment of heavy-metal-contaminated material. LEADX(reg s ign) chemically bonds to any free heavy metals that it contacts and forms a stable, non-leachable molecule. After treating the sludge with LEADX(reg s ign), it was to be left in the basin and the pool filled with grout. The successful treatment of the sludge with LEADX(reg s ign) will reduce the amount of waste to be disposed at the burial ground by eliminating the need to remove the sludge from the basin. Many off-gas and duct systems being dismantled contain dust and lint that has been contaminated

Application of Model Project Based Learning on Integrated Science in Water Pollution

Science.gov (United States)

Yamin, Y.; Permanasari, A.; Redjeki, S.; Sopandi, W.

2017-09-01

The function of this research was to analyze the influence model Project Based Learning (PjBl) on integrated science about the concept mastery for junior high school students. Method used for this research constitutes the quasi of experiment method. Population and sample for this research are the students junior high school in Bandung as many as two classes to be experiment and control class. The instrument that used for this research is the test concept mastery, assessment questionnaire of product and the questionnaire responses of the student about learning integrated science. Based on the result of this research get some data that with accomplishment the model of PjBl. Learning authority of integrated science can increase the concept mastery for junior high school students. The highest increase in the theme of pollution water is in the concept of mixtures and the separation method. The students give a positive response in learning of integrated science for the theme of pollution of the water used model PjBL with questionnaire of the opinion aspect in amount of 83.5%, the anxiety of the students in amount of 95.5%, the profit learning model of PjBL in amount of 96.25% and profit learning of integrated science in amount of 95.75%.

Annual report of waste generation and pollution prevention progress 1998; ANNUAL

International Nuclear Information System (INIS)

NONE

1999-01-01

This seventh Annual Report presents and analyzes DOE Complex-wide waste generation and pollution prevention activities at 45 reporting sites from 1993 through 1998. This section summarizes Calendar Year 1998 Complex-wide waste generation and pollution prevention accomplishments. More detailed information follows this section in the body of the Report. In May 1996, the Secretary of Energy established a 50 percent Complex-Wide Waste Reduction Goal (relative to the 1993 baseline) for routine operations radioactive, mixed, and hazardous waste generation, to be achieved by December31, 1999. DOE has achieved its Complex-Wide Waste Reduction Goals for routine operations based upon a comparison of 1998 waste generation to the 1993 baseline. Excluding sanitary waste, routine operations waste generation decreased 67 percent overall from 1993 to 1998. However, for the first time since 1994, the total amount of materials recycled by the Complex decreased from 109,600 metric tons in 1997 to 92,800 metric tons in 1998. This decrease is attributed to the fact that in 1997, several large ''one-time only'' recycling projects were conducted throughout the Complex. In order to demonstrate commitment to DOE's Complex-wide recycling goal, it is important for sites to identify all potential large-scale recycling/reuse opportunities

Geostatistical integration and uncertainty in pollutant concentration surface under preferential sampling

Directory of Open Access Journals (Sweden)

Laura Grisotto

2016-04-01

Full Text Available In this paper the focus is on environmental statistics, with the aim of estimating the concentration surface and related uncertainty of an air pollutant. We used air quality data recorded by a network of monitoring stations within a Bayesian framework to overcome difficulties in accounting for prediction uncertainty and to integrate information provided by deterministic models based on emissions meteorology and chemico-physical characteristics of the atmosphere. Several authors have proposed such integration, but all the proposed approaches rely on representativeness and completeness of existing air pollution monitoring networks. We considered the situation in which the spatial process of interest and the sampling locations are not independent. This is known in the literature as the preferential sampling problem, which if ignored in the analysis, can bias geostatistical inferences. We developed a Bayesian geostatistical model to account for preferential sampling with the main interest in statistical integration and uncertainty. We used PM10 data arising from the air quality network of the Environmental Protection Agency of Lombardy Region (Italy and numerical outputs from the deterministic model. We specified an inhomogeneous Poisson process for the sampling locations intensities and a shared spatial random component model for the dependence between the spatial location of monitors and the pollution surface. We found greater predicted standard deviation differences in areas not properly covered by the air quality network. In conclusion, in this context inferences on prediction uncertainty may be misleading when geostatistical modelling does not take into account preferential sampling.

Economic analysis of the CLC/FC regime as an oil pollution prevention instrument

International Nuclear Information System (INIS)

Hay, J.

2006-09-01

The aim of this research is to discuss the effectiveness of CLC/IOPC (Civil Liability Convention) liability regime in the field of oil pollution prevention. This study is mainly carried out from a law and economics perspective, although reference is also made to the economic analysis of international environmental agreements. The first two chapters explore the deterrent potential of the international regime in terms of oil spill prevention, from a theoretical and empirical perspective. The analysis of the effectiveness of the regime as such consists in, on the one hand, considering the ability of the international regime to compensate the entire social costs of oil spills (chapter 3) and, on the other hand, to examine the incentives given to operators in maritime oil transport to prevent accidental pollution (chapters 4 and 5). Sixth chapter considers the impacts of the voluntary nature of the international regime on its deterrent potential. The results obtained from this analysis enable to identify several mechanisms by which the deterrent effect of the existing regime could be increased. However, the overall effectiveness of the international regime appears to be limited by several factors that can not be corrected by means of a modification of the CLC and IOPC conventions. (author)

Integrated effects of air pollution and climate change on forests: A northern hemisphere perspective

International Nuclear Information System (INIS)

Bytnerowicz, Andrzej; Omasa, Kenji; Paoletti, Elena

2007-01-01

Many air pollutants and greenhouse gases have common sources, contribute to radiative balance, interact in the atmosphere, and affect ecosystems. The impacts on forest ecosystems have been traditionally treated separately for air pollution and climate change. However, the combined effects may significantly differ from a sum of separate effects. We review the links between air pollution and climate change and their interactive effects on northern hemisphere forests. A simultaneous addressing of the air pollution and climate change effects on forests may result in more effective research, management and monitoring as well as better integration of local, national and global environmental policies. - Simultaneous addressing air pollution and climate change effects on forests is an opportunity for capturing synergies in future research and monitoring

Application of local exhaust ventilation system and integrated collectors for control of air pollutants in mining company.

Science.gov (United States)

Ghorbani Shahna, Farshid; Bahrami, Abdulrahman; Farasati, Farhad

2012-01-01

Local exhaust ventilation (LEV) systems and integrated collectors were designed and implemented in a mining company in order to control emitted air pollutant from furnaces. The LEV was designed for capture and transition of air pollutants emitted from furnaces to the integrated collectors. The integrated collectors including four high efficiency Stairmand model cyclones for control of particulate matter, a venturi scrubber for control of the fine particles, SO(2) and a part of H(2)S to follow them, and a packed scrubber for treatment of the residual H(2)S and SO(2) were designed. Pollutants concentration were measured to determine system effectiveness. The results showed that the effectiveness of LEV for reducing workplace pollution is 91.83%, 96.32% and 83.67% for dust, SO(2) and H(2)S, respectively. Average removal efficiency of particles by combination of cyclone and venturi scrubber was 98.72%. Average removal efficiency of SO(2) and H(2)S were 95.85% and 47.13% for the venturi scrubber and 68.45% and 92.7% for the packed bed scrubber. The average removal efficiency of SO(2) and H(2)S were increased to 99.1% and 95.95% by the combination of venturi and packed bed scrubbers. According to the results, integrated collectors are a good air pollution control option for industries with economic constraints and ancient technologies.

Integrative Application of Life Cycle Assessment and Risk Assessment to Environmental Impacts of Anthropogenic Pollutants at a Watershed Scale.

Science.gov (United States)

Lin, Xiaodan; Yu, Shen; Ma, Hwongwen

2018-01-01

Intense human activities have led to increasing deterioration of the watershed environment via pollutant discharge, which threatens human health and ecosystem function. To meet a need of comprehensive environmental impact/risk assessment for sustainable watershed development, a biogeochemical process-based life cycle assessment and risk assessment (RA) integration for pollutants aided by geographic information system is proposed in this study. The integration is to frame a conceptual protocol of "watershed life cycle assessment (WLCA) for pollutants". The proposed WLCA protocol consists of (1) geographic and environmental characterization mapping; (2) life cycle inventory analysis; (3) integration of life-cycle impact assessment (LCIA) with RA via characterization factor of pollutant of interest; and (4) result analysis and interpretation. The WLCA protocol can visualize results of LCIA and RA spatially for the pollutants of interest, which might be useful for decision or policy makers for mitigating impacts of watershed development.

Climate change and local pollution effects. An integrated approach

International Nuclear Information System (INIS)

Aaheim, H.A.; Kristin, A.; Seip, H.M.

1999-01-01

Few studies on measures for mitigation of damage caused by man-made emissions to the environment have tried to consider all major effects. We illustrate the importance of an integrated approach by estimating costs and benefits of a proposed energy saving program for Hungary, originally designed to reduce CO 2 emissions. The dominant benefit of implementing the program is likely to be reduced health damage from local pollutants. Also reduced costs of material damage and to a lesser extent vegetation damage contribute to make the net benefit considerable. Compared to the reduction in these local and regional effects, the benefits from reducing greenhouse gases are likely to be minor. Since local effects in general occur much earlier after measures have been implemented than effects of increased emissions of greenhouse gases, inclusion of local effects makes evaluation of climate policy less dependent on the choice of discount rate. In our opinion, similar results are likely for many measures originally designed to reduce emissions of greenhouse gases particularly in some areas in developing countries with high local pollution levels. Main uncertainties in the analysis, e.g. in the relationships between damage and pollution level, are discussed. 72 refs

Benzimidazole for the prevention of toxic effects of air pollutants on plants

Energy Technology Data Exchange (ETDEWEB)

Takaoka, I; Fukuda, M; Kitano, H; Shinohara, T

1974-02-02

Tobacco plants were sprayed with benzimidazole before being exposed to 30 ppM of photochemical oxidants for a period of two hours. The plants were observed 48 hours after exposure and found to have suffered no toxic effects from the oxidants. It may be concluded that benzimidazole is an effective agent for preventing the toxic effects of air pollutants, such as photochemical oxidants on plants.

What drives successful implementation of pollution prevention and cleaner technology strategy? The role of innovative capability.

Science.gov (United States)

Bhupendra, Kumar Verma; Sangle, Shirish

2015-05-15

Firms that are dynamic and prepared to implement environmental strategies have a potential competitive advantage over their industry counterparts. Therefore, it is important to understand, what capabilities are required to implement proactive environmental strategies. The paper discusses the attributes of innovative capability required by firms in order to adopt pollution prevention and cleaner technology strategies. Empirical results show that process and behavioral innovativeness are required by firms to implement a pollution prevention strategy. In addition to process and behavioral innovativeness, firms need a top management with high risk-taking ability as well as market, product, and strategic innovativeness to implement a cleaner technology strategy. The paper proposes some important managerial implications on the basis of the above research findings. Copyright © 2015 Elsevier Ltd. All rights reserved.

Amoco-US Environmental Protection Agency, pollution prevention project, Yorktown, Virginia: Surface water data

International Nuclear Information System (INIS)

Baloo, S.

1991-08-01

The report summarizes the surface water sampling program at the Amoco Refinery at Yorktown, Virginia. This was undertaken as a part of the joint project between Amoco Corporation and the United States Environmental Protection Agency to review pollution prevention alternatives at a petroleum refinery. The surface water data provides a snapshot of surface water pollutant generation and discharge from the refinery. Different process units contribute to the total wastewater flow of 460 GPM in the refinery. Water in the ditch system, which is non-process water, is free of organic contamination. Oil and grease, phenols, ammonia and sulfides are the significant components measured in the process wastewater. The concentrations of organics in most water streams leaving the individual process units are relatively low, in the 1-5 parts per million (ppm) range. A few individual streams such as the crude desalter brine and tank water draws have high pollutant loadings. Concentrations of metals in the refinery wastewater are very low. The wastewater treatment plant is very effective in reducing the pollutant loading in the water with overall removal efficiencies greater than 99% for most organics and inorganics

Arima and integrated arfima models for forecasting air pollution index in Shah Alam, Selangor

International Nuclear Information System (INIS)

Lim, Ying Siew; Lim, Ying Chin; Pauline, Mah Jin Wee

2008-01-01

Air pollution is one of the major issues that has been affecting human health, agricultural crops, forest species and ecosystems. Since 1980, Malaysia has had a series of haze episodes and the worst ever was reported in 1997. As a result, the government has established the Malaysia Air Quality Guidelines, the Air Pollution Index (API) and Haze Action Plan, to improve the air quality. The API was introduced as an index system for classifying and reporting the ambient air quality in Malaysia. The API for a given period is calculated based on the sub-index value (sub-API) for all the five air pollutants, namely sulphur dioxide (SO 2 ), nitrogen dioxide (NO 2 ), ozone (O 3 ), carbon monoxide (CO) and particulate matter below 10 micron size (PM 10 ). The forecast of air pollution can be used for air pollution assessment and management. It can serve as information and warning to the public in cases of high air pollution levels and for policy management of many different chemical compounds. Hence, the objective of this project is to fit and illustrate the use of time series models in forecasting the API in Shah Alam, Selangor. The data used in this study consists of 70 monthly observations of API (from March 1998 to December 2003) published in the Annual Reports of the Department of Environment, Selangor. The time series models that were being considered were the Integrated Autoregressive Moving Average (ARIMA) and the Integrated Long Memory Model (ARFIMA) models. The lowest MAE, RMSE and MAPE values were used as the model selection criteria. Between these two models considered, the integrated ARFIMA model appears to be the better model as it has the lowest MAPE value. However, the actual value of May 2003 falls outside the 95% forecast interval, probably due to emissions from mobile sources (i.e., motor vehicles), industrial emissions, burning of solid wastes and forest fires. (author)

Preventing industrial pollution at its source: the final report of the Michigan source reduction initiative

Energy Technology Data Exchange (ETDEWEB)

None

1999-09-01

This report describes a collaborative effort between NRDC, Dow Chemical, and Michigan Environmental Groups. The effort resulted in the identification and implementation of 17 pollution prevention projects that reduced substantial quantities of wastes and emissions and saved Dow considerable money.

POLLUTION PREVENTION OPPORTUNITY ASSESSMENT OF THE UNITED STATES ARMY CORPS OF ENGINEERS GARRISON DAM HYDRO- ELECTRIC POWERPLANT - RIVERDALE, NORTH DAKOTA

Science.gov (United States)

The report describes the results of pollution prevention opportunity assessments conducted at a representative U.S. Army Corps of Engineers civil works dam and hydroelectric power plant. ecommended methods for reducing pollution resulting primarily from the operation of these fac...

15 CFR 291.4 - National industry-specific pollution prevention and environmental compliance resource centers.

Science.gov (United States)

2010-01-01

... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false National industry-specific pollution prevention and environmental compliance resource centers. 291.4 Section 291.4 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade NATIONAL INSTITUTE OF STANDARDS AND TECHNOLOGY, DEPARTMENT OF COMMERCE NIST EXTRAMURAL PROGRAM...

Achieving multiple compliance objectives through a storm water pollution prevention plan

Energy Technology Data Exchange (ETDEWEB)

Wagner, K.J.; Cataldo, R. [ENSR, Acton, MA (United States)

1997-09-01

All across the US, facility managers and environmental staff are trying to keep up with proliferating regulations and associated filing and reporting requirements. Added to the already full plate of regulations is the National Pollutant Discharge Elimination System (NPDES) program for storm water management. The NPDES program requires a permit for the discharge of runoff from facilities based on Standard Industrial Classification (SIC) code. Some businesses do not yet need to comply with NPDES, as not all types of facilities were included in the Phase 1 list of regulated activities (September 1992). However, most businesses will be included as part of Phase 2 by 2002. Furthermore, states adopting administration of the NPDES program have the option of accelerating the process. In addition to filing for a permit, the NPDES storm water program requires the preparation and implementation of a Storm Water Pollution Prevention Plan (SWPPP). A properly prepared SWPPP can help facilities more easily comply with regulatory requirements and serve as an overall facility management tool.

An Integrative Study of Photochemical Air Pollution in Hong Kong: an Overview

Science.gov (United States)

Wang, T.

2014-12-01

Hong Kong is situated in the Pearl River delta of Southern China. This region has experienced phenomenal economic growth in the past 30 years. Emissions of large amount of pollutants from urban areas and various industries coupled with subtropical climate have led to frequent occurrences of severe photochemical air pollution. Despite the long-term control efforts of the Hong Kong government, the atmospheric levels of ozone have been increasing in the past decade. To obtain an updated and more complete understanding of photochemical smog, an integrative study has been conducted during 2010-2014. Several intensive measurement campaigns were carried out at urban, suburban and rural sites in addition to the routine observations at fourteen air quality monitoring stations in Hong Kong. Meteorological, photochemical, and chemical-transport modeling studies were conducted to investigate the causes/processes of elevated photochemical pollution . The main activities of this study were to (1) examine the situation and trends of photochemical air pollution in Hong Kong, (2) understand some underlying chemical processes in particular the poorly-understood heterogeneous processes of reactive nitrogen oxides, (3) quantify the local, regional, and super-regional contributions to the ozone pollution in Hong Kong, and (4) review the control policy and make further recommendations based on the science. This paper will give an overview of this study and present some key results on the trends and chemistry of the photochemical pollution in this polluted subtropical region.

Stormwater Pollution Prevention Plan TA-60 Roads and Grounds Facility and Associated Sigma Mesa Staging Area

Energy Technology Data Exchange (ETDEWEB)

Sandoval, Leonard Frank [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-02-01

This Stormwater Pollution Prevention Plan (SWPPP) is applicable to operations at the Technical Area -60 (TA-60) Roads and Grounds Facility and Associated Sigma Mesa Staging Area off Eniwetok Drive, in Los Alamos County, New Mexico.

Climate change and occupational allergies: an overview on biological pollution, exposure and prevention.

Science.gov (United States)

D'Ovidio, Maria Concetta; Annesi-Maesano, Isabella; D'Amato, Gennaro; Cecchi, Lorenzo

2016-01-01

Climate change, air pollution, temperature increase and other environmental variables are modifying air quality, contributing to the increase of prevalence of allergic respiratory diseases. Allergies are complex diseases characterized by multilevel interactions between individual susceptibility, response to immune modulation and environmental exposures to physical, chemical and biological agents. Occupational allergies introduce a further complexity to these relationships by adding occupational exposure to both the indoor and outdoor ones in the living environment. The aim of this paper is to overview climate-related allergy affecting environmental and occupational health, as literature data are scanty in this regard, and to suggest a management model of this risk based on a multidisciplinary approach, taking the case of biological pollution, with details on exposure and prevention. The management of climate-related occupational allergy should take into account preventive health strategies, environmental, public and occupational interventions, as well as to develop, implement, evaluate, and improve guidelines and standards protecting workers health under changing climatic conditions; new tools and strategies based on local conditions will have to be developed. Experimental studies and acquisition of environmental and personal data have to be matched to derive useful information for the scope of occupational health and safety.

Pollution prevention opportunity assessment for the K-25 Site Steam Plant -- Level 3

International Nuclear Information System (INIS)

1995-09-01

A Level 3 pollution prevention opportunity assessment (PPOA) was performed for the K-1501 Steam Plant at the K-25 Site. The primary objective was to identify and evaluate pollution prevention (P2) options to reduce the quantities of each waste stream generated by the Steam Plant. For each of the waste streams, P2 options were evaluated to first reduce the quantity of waste generated and second to recycle the waste. This report provides a process description of the facility; identification, evaluation, and recommendations of P2 options; an implementation schedule with funding sources; and conclusions. Largely for economic reasons, only 3 of the 14 P2 options are being recommended for implementation. All are source reduction options. When implemented, these three options are estimated to reduce the annual generation of waste by 658,412 kg and will result in a cost savings of approximately $29,232/year for the K-25 Site. The recommended options are to: install a flue gas return System in Boiler 7; reduce steam loss from traps; and increase lapse time between rinses. The four boilers currently in operation at the Steam Plant use natural gas or fuel oil as fuel sources

L'IIASA and the integrated simulation of the trans-border atmospheric pollution assessment and evaluation

International Nuclear Information System (INIS)

Soleille, S.; Brignon, J.M.; Farret, R.; Landrieu, G.; Le Gall, A.C.; Rouil, L.

2003-09-01

The RAINS model is an integrated evaluation model for many pollutants and many effects, developed by he IIASA. This model studies the emissions of 4 atmospheric pollutants (nitrogen oxides, sulfur oxides, ammonium and volatile organic compounds) and the necessary costs to reduce them and the dispersion of these pollutants and their effects (tropospheric ozone formation, acidification and eutrophication). The model can be used in activities scenario mode (energy, agriculture, transports...) to calculate the emissions and their effects or in optimization mode to calculate strategies of emissions control from environmental constraints. (A.L.B.)

Pollution prevention opportunity assessment for the K-25 Site Toxic Substances Control Act Incinerator Operations, Level III

International Nuclear Information System (INIS)

1995-09-01

A Level III pollution prevention opportunity assessment (PPOA) was performed for the Oak Ridge K-25 Site Toxic Substances Control Act (TSCA) Incinerator to evaluate pollution prevention (P2) options for various waste streams: The main objective of this study was to identify and evaluate options to reduce the quantities of each waste stream generated by the TSCA Incinerator operations to realize significant environmental and/or economic benefits from P2. For each of the waste streams, P2 options were evaluated following the US Environmental Protection Agency (EPA) hierarchy to (1) reduce the quantity of waste generated, (2) recycle the waste, and/or (3) use alternate waste treatment or segregation methods. This report provides process descriptions, identification and evaluation of P2 options, and final recommendations

Non point source pollution modelling in the watershed managed by Integrated Conctructed Wetlands: A GIS approach.

OpenAIRE

Vyavahare, Nilesh

2008-01-01

The non-point source pollution has been recognised as main cause of eutrophication in Ireland (EPA Ireland, 2001). Integrated Constructed Wetland (ICW) is a management practice adopted in Annestown stream watershed, located in the south county of Waterford in Ireland, used to cleanse farmyard runoff. Present study forms the annual pollution budget for the Annestown stream watershed. The amount of pollution from non-point sources flowing into the stream was simulated by using GIS techniques; u...

Information processing to determine waste minimization/pollution prevention strategies in the petroleum industry

Energy Technology Data Exchange (ETDEWEB)

Falcon, Mariali F. de [CORPOVEN, S.A. (Venezuela)

1994-12-31

With the passage of the 1984 Hazardous and Solid Waste Amendments to the Resource Conservation and Recovery Act in the United States, industries, and particularly the petroleum industry, have become more interested in their waste management practices. This works aims to present a methodology to organize the collected data concerning waste minimization and, or, pollution prevention in the petroleum industry into a bibliographic database

Information processing to determine waste minimization/pollution prevention strategies in the petroleum industry

Energy Technology Data Exchange (ETDEWEB)

Falcon, Mariali F. de [CORPOVEN, S.A. (Venezuela)

1993-12-31

With the passage of the 1984 Hazardous and Solid Waste Amendments to the Resource Conservation and Recovery Act in the United States, industries, and particularly the petroleum industry, have become more interested in their waste management practices. This works aims to present a methodology to organize the collected data concerning waste minimization and, or, pollution prevention in the petroleum industry into a bibliographic database

High-resolution modelling of health impacts from air pollution using the integrated model system EVA

Science.gov (United States)

Brandt, Jørgen; Andersen, Mikael S.; Bønløkke, Jakob; Christensen, Jesper H.; Geels, Camilla; Hansen, Kaj M.; Jensen, Steen S.; Ketzel, Matthias; Plejdrup, Marlene S.; Sigsgaard, Torben; Silver, Jeremy D.

2014-05-01

A high-resolution assessment of health impacts from air pollution and related external cost has been conducted for Denmark using the integrated EVA model system. The EVA system has been further developed by implementing an air quality model with a 1 km x 1 km resolution covering the whole of Denmark. New developments of the integrated model system will be presented as well as results for health impacts and related external costs over several decades. Furthermore, the sensitivity of health impacts to model resolution will be studied. We have developed an integrated model system EVA (Economic Valuation of Air pollution), based on the impact-pathway chain, to assess the health impacts and health-related economic externalities of air pollution resulting from specific emission sources or sectors. The system is used to support policymaking with respect to emission control. In Brandt et al. (2013a; 2013b), the EVA system was used to assess the impacts in Europe and Denmark from the past, present and future total air pollution levels as well as the contribution from the major anthropogenic emission sectors. The EVA system was applied using the hemispheric chemistry-transport model, the Danish Eulerian Hemispheric Model (DEHM), with nesting capability for higher resolution over Europe (50 km x 50 km) and Northern Europe (16.7 km x 16.7 km). In this study an Urban Background Model (UBM) has been further developed to cover the whole of Denmark with a 1 km x 1 km resolution and the model has been implemented as a part of the integrated model system, EVA. The EVA system is based on the impact-pathway methodology. The site-specific emissions will result (via atmospheric transport and chemistry) in a concentration distribution, which together with detailed population data, are used to estimate the population-level exposure. Using exposure-response functions and economic valuations, the exposure is transformed into impacts on human health and related external costs. In this study

Integrated fuel cell stack shunt current prevention arrangement

Energy Technology Data Exchange (ETDEWEB)

Roche, Robert P. (Cheshire, CT); Nowak, Michael P. (Bolton, CT)

1992-01-01

A fuel cell stack includes a plurality of fuel cells juxtaposed with one another in the stack and each including a pair of plate-shaped anode and cathode electrodes that face one another, and a quantity of liquid electrolyte present at least between the electrodes. A separator plate is interposed between each two successive electrodes of adjacent ones of the fuel cells and is unified therewith into an integral separator plate. Each integral separator plate is provided with a circumferentially complete barrier that prevents flow of shunt currents onto and on an outer peripheral surface of the separator plate. This barrier consists of electrolyte-nonwettable barrier members that are accommodated, prior to the formation of the integral separator plate, in corresponding edge recesses situated at the interfaces between the electrodes and the separator plate proper. Each barrier member extends over the entire length of the associated marginal portion and is flush with the outer periphery of the integral separator plate. This barrier also prevents cell-to-cell migration of any electrolyte that may be present at the outer periphery of the integral separator plate while the latter is incorporated in the fuel cell stack.

Integrated assessment of agricultural land use policies on nutrient pollution and sustainable development in Taihu Basin, China

NARCIS (Netherlands)

Reidsma, P.; Feng, S.; Loon, van M.; Luo, X.; Kang, C.; Lubbers, M.T.M.H.; Kanellopoulos, A.; Wolf, J.; Ittersum, van M.K.; Qu, F.

2012-01-01

Water pollution in Chinese lakes is a major problem. To reduce nutrient pollution and enhance sustainable development in Taihu Basin, China, an integrated assessment of the impacts of agricultural land use policies has been performed, using the technical coefficient generator TechnoGIN and the

Prevention and Control of Air Pollution in China: A Research Agenda for Science and Technology Studies

OpenAIRE

Hernandez, Rodolfo Andres

2016-01-01

China’s air pollution has reached a critical state, and is characterized by heavy coal smoke and a wide presence of ozone and particulate matter (PM2.5). From 2011, through the 12th five year plan, the prevention and control of air pollution entered a new ‘transition stage’ guided by the principles of sustainability and energy conservation, and also intensified by pressure from the society. This article is divided into two parts: first, it introduces the most important changes, problems and a...

The '333' integrated strategy for effective pollution control and its application to the heavily polluted Jialu River in north China.

Science.gov (United States)

Huang, Yu; Sun, Jie; Li, Aimin; Xie, Xianchuan

2018-05-01

In this study, an integrated approach named the '333' strategy was applied to pollution control in the Jialu River, in northern China, which is heavily burdened with anthropogenic pollution. Due to a deficiency of the natural ecological inflow, the Jialu River receives predominantly industrial and municipal effluent. The '333' strategy is composed of three steps of pollution control including industrial point-source pollution control, advanced treatment of municipal wastewater, and ecological restoration; three increased stringency emission standards; and three stages of reclamation. Phase 1 of the '333' strategy focuses on industrial point-source pollution control; phase 2 aims to harness municipal wastewater and minimize sewage effluents using novel techniques for advanced water purification; phase 3 of the '333' strategy focuses on the further purification of effluents flowing into Jialu River with the employment of an engineering-based ecological restoration project. The application of the '333' strategy resulted in the development of novel techniques for water purification including modified magnetic resins (NDMP resin), a two-stage internal circulation anaerobic reactor (IC reactor) and an ecological restoration system. The results indicate that water quality in the river was significantly improved, with increased concentrations of dissolved oxygen (DO), as well as reduction of COD by 42.8% and NH 3 -N by 61.4%. In addition, it was observed that the total population of phytoplankton in treated river water notably increased from only one prior to restoration to 8 following restoration. This system also provides a tool for pollution control of other similar industrial and anthropogenic source polluted rivers.

EVALUATION OF POLLUTION PREVENTION OPTIONS TO REDUCE STYRENE EMISSIONS FROM FIBER-REINFORCED PLASTIC OPEN MOLDING PROCESSES

Science.gov (United States)

Pollution prevention (P2) options to reduce styrene emissions, such as new materials, and application equipment, are commercially available to the operators of open molding processes. However, information is lacking on the emissions reduction that these options can achieve. To me...

Development of a method to evaluate the technical and environmental feasibility of particular pollution prevention opportunities.

Science.gov (United States)

2000-06-01

The Virginia Department of Transportation (VDOT) is obligated by House Joint Resolution 453 passed in 1995 by Virginia's General Assembly to develop and implement a pollution prevention (P2) program. The primary purpose of this study was to develop a...

Preventing industrial pollution at its source: the final report of the Michigan source reduction initiative; FINAL

International Nuclear Information System (INIS)

None

1999-01-01

This report describes a collaborative effort between NRDC, Dow Chemical, and Michigan Environmental Groups. The effort resulted in the identification and implementation of 17 pollution prevention projects that reduced substantial quantities of wastes and emissions and saved Dow considerable money

PREVENTING POLLUTION USING ISO 14001 AT A PARTICLE ACCELERATOR THE RELATIVISTIC HEAVY ION COLLIDER PROJECT

International Nuclear Information System (INIS)

BRIGGS, S.L.K.; MUSOLINO, S.V.

2001-01-01

In early 1997 Brookhaven National Laboratory (BNL) discovered that the spent fuel pool of their High Flux Beam Reactor was leaking tritium into the groundwater. Community members, activist groups, politicians and regulators were outraged with the poor environmental management practices at BNL. The reactor was shut down and the Department of Energy (DOE) terminated the contract with the existing Management Company. At this same time, a major new scientific facility, the Relativistic Heavy Ion Collider (RHIC), was nearing the end of construction and readying for commissioning. Although environmental considerations had been incorporated into the design of the facility; some interested parties were skeptical that this new facility would not cause significant environmental impacts. RHIC management recognized that the future of its operation was dependent on preventing pollution and allaying concerns of its stakeholders. Although never done at a DOE National Laboratory before Brookhaven Science Associates, the new management firm, committed to implementing an Environmental Management System (EMS) and RHIC managers volunteered to deploy it within their facility on an extremely aggressive schedule. Several of these IS0 requirements contribute directly to preventing pollution, an area where particular emphasis was placed. This paper describes how Brookhaven used the following key IS0 14001 elements to institutionalize Pollution Prevention concepts: Environmental Policy, Aspects, Objectives and Targets, Environmental Management Program, Structure and Responsibility, Operational Controls, Training, and Management Review. In addition, examples of implementation at the RHIC Project illustrate how BNL's premiere facility was able to demonstrate to interested parties that care had been taken to implement technological and administrative controls to minimize environmental impacts, while at the same time reduce the applicability of regulatory requirements to their operations

Environmental and risk screening for prioritizing pollution prevention opportunities in the U.S. printed wiring board manufacturing industry.

Science.gov (United States)

Lam, Carl W; Lim, Seong-Rin; Schoenung, Julie M

2011-05-15

Modern manufacturing of printed wiring boards (PWBs) involves extensive use of various hazardous chemicals in different manufacturing steps such as board preparation, circuit design transfer, etching and plating processes. Two complementary environmental screening methods developed by the U.S. EPA, namely: (i) the Tool for the Reduction and Assessment of Chemical and Other Environmental Impacts (TRACI) and (ii) Risk-Screening Environmental Indicators (RSEI), are used to quantify geographic and chemical environmental impacts in the U.S. PWB manufacturing industry based on Toxics Release Inventory (TRI) data. Although the release weight percentages of industrial chemicals such as methanol, glycol ethers and dimethylformamide comprise the larger fraction of reported air and water emissions, results indicate that lead, copper and their compounds' releases correspond to the highest environmental impact from toxicity potentials and risk-screening scores. Combining these results with further knowledge of PWB manufacturing, select alternative chemical processes and materials for pollution prevention are discussed. Examples of effective pollution prevention options in the PWB industry include spent etchant recovery technologies, and process and material substitutions. In addition, geographic assessment of environmental burden highlights states where promotion of pollution prevention strategies and emissions regulations can have the greatest effect to curb the PWB industry's toxic release impacts. Copyright © 2011 Elsevier B.V. All rights reserved.

Hanford site guide for preparing and maintaining generator group pollution prevention program documentation

International Nuclear Information System (INIS)

1995-12-01

This manual provides the necessary guidance to contractor generator groups for developing and maintaining documentation of their pollution prevention (P2) program activities. Preparation of program documentation will demonstrate compliance with contractor and U.S. Department of Energy (DOE) requirements, as well as state and federal regulations. Contractor waste generator groups are no longer required to prepare and update facility waste minimization plans. Developing and maintaining program documentation replace this requirement

Proceedings of pollution prevention and waste minimization tools workshop

International Nuclear Information System (INIS)

1995-01-01

Pollution Prevention (P2) has evolved into one of DOE's sprime strategies to meet environmental, fiscal, and worker safety obligations. P2 program planning, opportunity identification, and implementation tools were developed under the direction of the Waste Minimization Division (EM-334). Forty experts from EM, DP, ER and DOE subcontractors attended this 2-day workshop to formulate the incentives to drive utilization of these tools. Plenary and small working group sessions were held both days. Working Group 1 identified incentives to overcoming barriers in the area of P2 program planning and resource allocation. Working Group 2 identified mechanisms to drive the completion of P2 assessments and generation of opportunities. Working Group 3 compiled and documented a broad range of potential P2 incentives that address fundamental barriers to implementation of cost effective opportunities

Pollution from pipelines

International Nuclear Information System (INIS)

1991-01-01

During the 1980s, over 3,900 spills from land-based pipelines released nearly 20 million gallons of oil into U.S. waters-almost twice as much as was released by the March 1989 Exxon Valdez oil spill. Although the Department of Transportation is responsible for preventing water pollution from petroleum pipelines, GAO found that it has not established a program to prevent such pollution. DOT has instead delegated this responsibility to the Coast Guard, which has a program to stop water pollution from ships, but not from pipelines. This paper reports that, in the absence of any federal program to prevent water pollution from pipelines, both the Coast Guard and the Environmental Protection Agency have taken steps to plan for and respond to oil spills, including those from pipelines, as required by the Clean Water Act. The Coast Guard cannot, however, adequately plan for or ensure a timely response to pipeline spills because it generally is unaware of specific locations and operators of pipelines

REPORT TO CONGRESS: ASSESSMENT OF INTERNATIONAL AIR POLLUTION PREVENTION AND CONTROL TECHNOLOGY VOLUME 1. EXECUTIVE SUMMARY

Science.gov (United States)

The report gives results of a study that identifies new and innovative air pollution prevention and/or control technologies, of selected industrialized countries, that are not currently used extensively in the U.S. The technologies may be entirely new to the U.S., or they may be ...

Deployment of pollution prevention during design -- a case study

International Nuclear Information System (INIS)

Del Mar, R.A.; Ambalam, T.T.

1997-08-01

Traditionally, pollution prevention (P2) assessments have been performed on existing facilities and ongoing operations, well after the completion of design and construction. It has been theorized that more success can be achieved by moving P2 upstream into the design process, where an estimated 70% of a project's total life cycle costs are initially fixed. Decisions made during design to prevent or minimize the amount of waste generated can reap benefits for many years to come. This is especially true when designing systems for handling hazardous and radioactive wastes for treatment, storage, and disposal. P2 assessments performed during design of such projects can uncover significant savings to be reaped during project construction, operations, and/or decommissioning. However, many project managers are still reluctant to include some type of P2 review or assessment as part of the design effort, because the immediate payback to the design entity is difficult to quantify. This paper presents the results of a P2 assessment performed on a design project at Hanford which identified close to $500,000 in construction savings while minimizing low-level and mixed radioactive waste generation. This paper describes the process used to per-form the assessment, discusses its results, and provides lessons-learned for future P2 design assessments

Variable Structure PID Control to Prevent Integrator Windup

Science.gov (United States)

Hall, C. E.; Hodel, A. S.; Hung, J. Y.

1999-01-01

PID controllers are frequently used to control systems requiring zero steady-state error while maintaining requirements for settling time and robustness (gain/phase margins). PID controllers suffer significant loss of performance due to short-term integrator wind-up when used in systems with actuator saturation. We examine several existing and proposed methods for the prevention of integrator wind-up in both continuous and discrete time implementations.

Uranium Mill Tailings remedial action project waste minimization and pollution prevention awareness program plan

International Nuclear Information System (INIS)

1994-07-01

The purpose of this plan is to establish a waste minimization and pollution prevention awareness (WM/PPA) program for the U.S. Department of Energy's (DOE) Uranium Mill Tailings Remedial Action (UMTRA) Project. The program satisfies DOE requirements mandated by DOE Order 5400.1. This plan establishes planning objectives and strategies for conserving resources and reducing the quantity and toxicity of wastes and other environmental releases

Macro impact of the law on prevention and control of atmospheric pollution on power industry development

Energy Technology Data Exchange (ETDEWEB)

Wang, Z. [State Power Corporation (China). Dept. of Science, Technology and Environment

2001-07-01

The newly revised and enlarged main contents of China's Law of Prevention and Control of Atmospheric Pollution, which came into force on 1 September 2000, are described. The macro impacts of the law on the power industry development are analyzed mainly in respect to power demand and readjustment of power structure and layout, clean production and pollution control level, scientific management of environmental protection, in accordance with law as well as changes of construction and operation costs. Several questions worthy to be noted in course of implementation of the new law are enumerated. 1 tab.

An Integrated Computer-Aided Approach for Environmental Studies

DEFF Research Database (Denmark)

Gani, Rafiqul; Chen, Fei; Jaksland, Cecilia

1997-01-01

A general framework for an integrated computer-aided approach to solve process design, control, and environmental problems simultaneously is presented. Physicochemical properties and their relationships to the molecular structure play an important role in the proposed integrated approach. The sco...... and applicability of the integrated approach is highlighted through examples involving estimation of properties and environmental pollution prevention. The importance of mixture effects on some environmentally important properties is also demonstrated....

Oil pollution

International Nuclear Information System (INIS)

Mankabady, Samir.

1994-08-01

Oil enters the marine environment when it is discharged, or has escaped, during transport, drilling, shipping, accidents, dumping and offshore operations. This book serves as a reference both on the various complex international operational and legal matters of oil pollution using examples such as the Exxon Valdez, the Braer and Lord Donaldson's report. The chapters include the development of international rules on the marine environment, the prevention of marine pollution from shipping activities, liability for oil pollution damage, the conflict of the 1990 Oil Pollution Act and the 1992 protocols and finally the cooperation and response to pollution incidents. (UK)

"APEC blue"--The effects and implications of joint pollution prevention and control program.

Science.gov (United States)

Wang, Hongbo; Zhao, Laijun; Xie, Yujing; Hu, Qingmi

2016-05-15

To ensure good air quality in Beijing during Asia-Pacific Economic Cooperation (APEC) China 2014, Beijing and its neighboring five provinces and the associated cities were combined under the Joint Prevention and Control of Atmospheric Pollution (JPCAP) program, which implemented rigorous cooperative emission reduction measures. The program was a unique and large-scale artificial experiment that showed that such measures can achieve excellent results, and it led to the popular "APEC blue" catchphrase (i.e., Beijing's skies became blue as pollution levels decreased). This artificial experiment provided the means to effectively conduct JPCAP strategies in the future. Accordingly, our research focused on the characteristics of the six primary pollutants in Beijing. We found that the JPCAP measures directly reduced concentrations of all pollutants except O3. Through correlation analysis, we found that the band distribution of the cities with strong correlations in PM2.5 and PM10 concentrations was affected by wind conditions. Therefore, JPCAP measures should account for specific seasonal and climatic conditions. Based on cluster analysis using the results from the correlation analysis, we divided 13 cities within a 300-km radius of Beijing into different groups according to the similarity of their PM2.5 and PM10 correlation coefficients. For JPCAP measures relevant to PM2.5 and PM10, we found differences in the degrees of collaboration among cities. Therefore, depending upon the pollutant type, the JPCAP strategy should account for the cities involved, the scope of the core area, and the optimal cities to involve in the collaborative efforts based on cost-effectiveness and collaborative difficulty among the involved cities. Copyright © 2016 Elsevier B.V. All rights reserved.

Water pollution control technology and strategy for river-lake systems: a case study in Gehu Lake and Taige Canal.

Science.gov (United States)

Zhang, Yimin; Zhang, Yongchun; Gao, Yuexiang; Zhang, Houhu; Cao, Jianying; Cai, Jinbang; Kong, Xiangji

2011-07-01

The Taoge water system is located in the upstream of Taihu Lake basin and is characterized by its multi-connected rivers and lakes. In this paper, current analyses of hydrology, hydrodynamics and water pollution of Gehu Lake and Taige Canal are presented. Several technologies are proposed for pollution prevention and control, and water environmental protection in the Taihu Lake basin. These included water pollution control integration technology for the water systems of Gehu Lake, Taige Canal and Caoqiao River. Additionally, river-lake water quality and quantity regulation technology, ecological restoration technology for polluted and degraded water bodies, and water environmental integration management and optimization strategies were also examined. The main objectives of these strategies are to: (a) improve environmental quality of relative water bodies, prevent pollutants from entering Gehu Lake and Taige Canal, and ensure that the clean water after the pre-treatment through Gehu Lake is not polluted before entering the Taihu Lake through Taige Canal; (b) stably and efficiently intercept and decrease the pollution load entering the lake through enhancing the river outlet ecological system structure function and water self-purifying capacity, and (c) designate Gehu Lake as a regulation system for water quality and water quantity in the Taoge water system and thus guarantee the improvement of the water quality of the inflow into Taihu Lake.

EVALUATION OF A PORTABLE FOURIER TRANSFORM INFRARED GAS ANALYZER FOR MEASUREMENTS OF AIR TOXICS IN POLLUTION PREVENTION RESEARCH

Science.gov (United States)

A portable Fourier transform infrared gas analyzer with a photoacoustic detector performed reliably during pollution prevention research at two industrial facilities. It exhibited good agreement (within approximately 6%) with other analytical instruments (dispersive infrared and ...

Integrated waste load allocation for river water pollution control under uncertainty: a case study of Tuojiang River, China.

Science.gov (United States)

Xu, Jiuping; Hou, Shuhua; Yao, Liming; Li, Chaozhi

2017-07-01

This paper presents a bi-level optimization waste load allocation programming model under a fuzzy random environment to assist integrated river pollution control. Taking account of the leader-follower decision-making in the water function zones framework, the proposed approach examines the decision making feedback relationships and conflict coordination between the river basin authority and the regional Environmental Protection Agency (EPA) based on the Stackelberg-Nash equilibrium strategy. In the pollution control system, the river basin authority, as the leader, allocates equitable emissions rights to different subareas, and the then subarea EPA, as the followers, reallocates the limited resources to various functional zones to minimize pollution costs. This research also considers the uncertainty in the water pollution management, and the uncertain input information is expressed as fuzzy random variables. The proposed methodological approach is then applied to Tuojiang River in China and the bi-level linear programming model solutions are achieved using the Karush-Kuhn-Tucker condition. Based on the waste load allocation scheme results and various scenario analyses and discussion, some operational policies are proposed to assist decision makers (DMs) cope with waste load allocation problem for integrated river pollution control for the overall benefits.

40 CFR Appendix L to Part 51 - Example Regulations for Prevention of Air Pollution Emergency Episodes

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 2 2010-07-01 2010-07-01 false Example Regulations for Prevention of Air Pollution Emergency Episodes L Appendix L to Part 51 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS REQUIREMENTS FOR PREPARATION, ADOPTION, AND SUBMITTAL OF IMPLEMENTATION PLANS Pt. 51, App. L Appendix L to Par...

A new integrated evaluation method of heavy metals pollution control during melting and sintering of MSWI fly ash.

Science.gov (United States)

Li, Rundong; Li, Yanlong; Yang, Tianhua; Wang, Lei; Wang, Weiyun

2015-05-30

Evaluations of technologies for heavy metal control mainly examine the residual and leaching rates of a single heavy metal, such that developed evaluation method have no coordination or uniqueness and are therefore unsuitable for hazard control effect evaluation. An overall pollution toxicity index (OPTI) was established in this paper, based on the developed index, an integrated evaluation method of heavy metal pollution control was established. Application of this method in the melting and sintering of fly ash revealed the following results: The integrated control efficiency of the melting process was higher in all instances than that of the sintering process. The lowest integrated control efficiency of melting was 56.2%, and the highest integrated control efficiency of sintering was 46.6%. Using the same technology, higher integrated control efficiency conditions were all achieved with lower temperatures and shorter times. This study demonstrated the unification and consistency of this method. Copyright © 2015 Elsevier B.V. All rights reserved.

Airlie House Pollution Prevention Technology Transfer pilot projects

Energy Technology Data Exchange (ETDEWEB)

Thuot, J.R.; Myron, H.; Gatrone, R.; McHenry, J.

1996-08-01

The projects were a series of pilot projects developed for DOE with the intention of transferring pollution prevention technology to private industry. The concept was to develop small technology transfer initiatives in partnership with the private sector. Argonne National Laboratory developed three projects: the microscale chemistry in education program, the microscale cost benefit study, and the Bethel New Life recycling trainee program. The two microscale chemistry projects focused on introducing microscale chemistry technologies to secondary and college education. These programs were inexpensive to develop and received excellent evaluations from participants and regulators. The recycle trainee project provided training for two participants and identified recycling and source reduction opportunities in Argonne`s solid waste stream. The pilot projects demonstrated that technology transfer initiatives can be developed and implemented with a small budget and within a short period of time. The essential components of the pilot projects were identification of target technologies that were already available, identification of target audiences, and a focus of effort to achieve a limited but defined objective.

Analysis of industrial pollution prevention programs in selected Asian countries

Energy Technology Data Exchange (ETDEWEB)

Chiu, S.Y. [Argonne National Lab., IL (United States). Environmental Assessment Div.]|[East-West Center, Honolulu, HI (United States)

1995-05-01

Industrialization in developing countries is causing increasing environmental damage. Pollution prevention (P2) is an emerging environmental concept that could help developing countries achieve leapfrog goals, bypassing old and pollutive technologies and minimizing traditional control practices. The current P2 promotion activities in Hong Kong, the Republic of Korea, the Philippines, Singapore, Taiwan, and Thailand are discussed. These programs, generally initiated in the last 5 years, are classified into five categories: awareness promotion, education and training, information transfer, technical assistance, and financial incentives. All important at the early stages of P2 promotion, these programs should inform industries of the benefits of P2 and help them identify applicable P2 measures. Participation in these programs is voluntary. The limited data indicate that adoption of P2 measures in these countries is not yet widespread. Recommendations for expanding P2 promotion activities include (1) strengthening the design and enforcement of environmental regulations; (2) providing P2 training and education to government workers, nongovernmental organizations and labor unions officials, university faculties, and news media; (3) tracking the progress of P2 programs; (4) implementing selected P2 mandatory measures; (5) identifying cleaner production technologies for use in new facilities; (6) implementing special programs for small and medium enterprises; and (7) expanding P2 promotion to other sectors, such as agriculture and transportation, and encouraging green design and green consumerism.

Integrating Buddhism and HIV prevention in U.S. southeast Asian communities.

Science.gov (United States)

Loue, S; Lane, S D; Lloyd, L S; Loh, L

1999-02-01

Asian Pacific Islander communities in the United States have experienced an alarming increase in HIV infection over the past few years, possibly due to a lack of knowledge and the relative absence of appropriate educational interventions. The authors propose a new approach to the development of HIV prevention programs in U.S. southeast Asian communities. This article reviews the cultural and economic factors that may facilitate HIV transmission within these communities. Relying on the basic precepts of Buddhism, the dominant religion of many southeast Asian populations in the United States, the health belief model is utilized to demonstrate how recognizable, acceptable religious constructs can be integrated into the content of HIV prevention messages. This integration of religious concepts with HIV prevention messages may increase the likelihood that the message audience will accept the prevention messages as relevant. This nuanced approach to HIV prevention must be validated and refined through field research.

Korea's transition to the IPCC : Introduction of BAT-based Integrated ACT

Science.gov (United States)

Lee, Daegyun; Yoo, Heungmin; Kim, Younglan

2017-04-01

Recently, environmental pollution concerns have been increased in Korea more than ever before. So, The Ministry of Environment and the National Institute of Environmental Research(NIER) in Korea has forged a policy that can effectively reduce the environmental pollutants emitted from each business sectors. This policy nicknamed the "Integrated Environmental Management Act" will be implemented from January 2017. It is to consolidate the management method of each environment media (such as water/atmosphere, etc.) and discharge facility into single authorization and/or permission system for entire installation. In particular, it is the environmental management system in according to the "Act on Integrated Management of Environmental Pollution Facilities" that encourages active participation of companies, grant customized emission permits by considering the ambient environmental condition as well as best available techniques, and review the permitted items periodically. Throughout this optimal management policy, we expect the minimization of the environmental effect by reducing the production and emission of pollutants. The integrated environmental management system is a scientific and advanced whole new management system and it is also a policy that considers the environment and human health effect in a synthetically, and minimizes the emission of pollutants by applying the best available techniques. In this presentation, we will talk about the Korea's transition stage to IPCC(integrated pollution prevention and control) and introduce the whole new Integrated Environmental Management system of Korea.

Report: Pollution Prevention: Effectiveness of EPA’s Efforts to Encourage Purchase of Recycled Goods Has Not Been Demonstrated

Science.gov (United States)

Report #2003-P-00013, Sept 22, 2003. In an effort to prevent pollution and conserve natural resources and virgin materials, Congress requires that the Federal Government’s purchasing power be used to steer materials away from disposal toward recycling.

Environmental Compliance and Pollution Prevention Training Manual for Campus-Based Organizations--Operational and Facility Maintenance Personnel.

Science.gov (United States)

New York State Dept. of Environmental Conservation, Albany.

This manual was designed to be used as part of the Workshop on Environmental Compliance and Pollution Prevention for campus-based facilities. It contains basic information on New York state and federal laws, rules, and regulations for protecting the environment. The information presented is a summary with emphasis on those items believed to be…

A joint prevention and control mechanism for air pollution in the Beijing-Tianjin-Hebei region in china based on long-term and massive data mining of pollutant concentration

Science.gov (United States)

Wang, Hongbo; Zhao, Laijun

2018-02-01

China's Beijing-Tianjin-Hebei (BTH) region suffers from the country's worst air pollution. The problem has caused widespread concern both at home and abroad. Based on long-term and massive data mining of PM2.5 and PM10 concentration, we found that these pollutants showed similar variations in four seasons, but the most severe pollution was in winter. Through cluster analysis of the winter daily average concentration (DAC) of the two pollutants, we defined regions with similar variations in pollutant concentrations in winter. For the most polluted cities in BTH, the relationship between correlation coefficients for winter DAC and the distance between cities revealed that PM2.5 has regional, large-scale characteristics, with concentrated outbreaks, whereas PM10 has local, small-scale characteristics, with outbreaks at multiple locations. By selecting the key cities with the strongest linear relationship between the pollutant's DAC of each city and the daily individual air quality index values of the BTH region and through cluster analysis on the correlations between the pollutant DACs of the key cities, we defined regional divisions suitable for Joint Prevention and Control of Atmospheric Pollution (JPCAP) program to control PM2.5 and PM10. Comprehensively considering the degree of influence of regional atmospheric pollution control (RAPC) on air quality in BTH, as well as the elasticity and urgency of RAPC, we defined the control grades of the JPCAP regions. We found both the regions and corresponding control grades were consistent for PM2.5 and PM10. The thinking and methods of atmospheric pollution control we proposed will have broad significance for implementation of RAPC in other regions around the world.

Air pollution policies in Europe: efficiency gains from integrating climate effects with damage costs to health and crops

International Nuclear Information System (INIS)

Tollefsen, Petter; Rypdal, Kristin; Torvanger, Asbjorn; Rive, Nathan

2009-01-01

Emissions of air pollutants cause damage to health and crops, but several air pollutants also have an effect on climate through radiative forcing. We investigate efficiency gains achieved by integrating climate impacts of air pollutants into air quality strategies for the EU region. The pollutants included in this study are SO 2 , NH 3 , VOC, CO, NO x , black carbon, organic carbon, PM 2.5 , and CH 4 . We illustrate the relative importance of climate change effects compared to damage to health and crops, as well as monetary gains of including climate change contributions. The analysis considers marginal abatement costs and compares air quality and climate damage in Euros. We optimize abatement policies with respect to both climate and health impacts, which imply implementing all measures that yield a net benefit. The efficiency gains of the integrated policy are in the order of 2.5 billion Euros, compared to optimal abatement based on health and crop damage only, justifying increased abatement efforts of close to 50%. Climate effect of methane is the single most important factor. If climate change is considered on a 20- instead of a 100-year time-scale, the efficiency gain almost doubles. Our results indicate that air pollution policies should be supplemented with climate damage considerations.

Turbo-gas emissions and integrated pollution prevention and control (IPPC); Emissioni da turbogas e prevenzione e limitazione integrata dell'inquinamento

Energy Technology Data Exchange (ETDEWEB)

Mariani, M. [ISPESL/DIPIA, Roma (Italy); Sera, B. [Roccadarce (Italy)

2005-10-15

The present paper considers the gas-turbine pollution and joints out that the NO, is the most important pollutant among others pollutants as well as the carbon oxide and the volatile organic compounds because the NO{sub x}, has a high mass production rate (in the combustion chamber), elevated toxicity to the ecosystem and because of being in the atmosphere a precursor of secondary ultrafine particles PM{sub 2,5}. In with reference to the integrated pollution and control (IPPC) the job shows schemes of chain chemical reactions which are on the base of the formation of different types of NO{sub x}, thermal and organic, and it illustrates the influence of some operative parameters on the combustion's efficiency and then on the NO{sub x}, production rate. Also, the study gives the best absolvable techniques (BAT) to reduce the NO{sub x}, production rate and to demolish it before its introduction, as well as gas exhaust, in the atmosphere. At the end, the work shows that the gas-turbine are to consider thermal engines with a little environment impact index specially when they make use of the natural gas, as well as fuel. [Italian] Lo studio considera gli inquinanti emessi dalle turbine a gas ed evidenzia che l'ossido di azoto NO, e quell'inquinante che e degno di attenzione a causa del suo alto tasso di produzione in camera di combustione (notevolmente piu alto di quello dell'ossido di carbonio e dei composti organici volatili), della sua elevata tossicita nei confronti dell'ecosistema e per il fatto di essere in atmosfera un precursore del particolato secondario ultrafino PM{sub 2},{sub 5}. In riferimento. alla prevenzione e limitazione integrata dell'inquinamento lo studio espone gli schemi di reazioni chimiche che sono alla base della formazione dei vari tipi di NO{sub x}, quello termico e quello organico, che si generano in camera di combustione ed inoltre illustra l'influenza di alcuni parametri operativi sull'efficienza del

Radioactive marine pollution

International Nuclear Information System (INIS)

Pontavice, E. du

1976-01-01

Certain provision in international law aim to prevent radioactive marine pollution and others concern compensation of damage from nuclear pollution. Prevention requires regulation of the disposal of wastes from nuclear industry from the operation of nuclear powered ships and from transport of fissile materials. As regards damage, if the measures to limit the extent of the damage come under the law of the sea, the priority of nuclear law over maritime law is clear in respect of financial compensation. (Auth) [fr

Pollution prevention in the analytical laboratory--Microscale and other techniques do add up

International Nuclear Information System (INIS)

Erickson, M.D.; Alvarado, J.S.; Lu, C.-S.; Peterson, D.P.; Silzer, J.

1996-01-01

The principles of pollution prevention in the analytical laboratory have not been addressed sufficiently. Although the amount of reagent used per sample is often only a few milliliters, the aggregate of many routine test each day in thousands of laboratories becomes significant. Current recycling practices are not practical with small streams. Therefore, we have adopted the principles of microscale chemistry, along with other modern analytical approaches, to develop routine analytical methods that significantly curtail waste but still maintain acceptable analytical figures of merit and achieve cost savings through reduced reagent consumption and reduced labor cost

Integrative approach for wastewater treatment facilities with biomass transformation into energy

OpenAIRE

Anker Yaakov; Mualem David; Langstadter Hagai; Nakonechny Faina; Nisnevitch Marina

2017-01-01

Current industrial environmental regulations favor processes with Integrative Pollution Prevention and Control (IPPC). While several systems are regarded by different international directives as IPPC Best Available Techniques or Technologies (BAT), none of these systems are capable handling various pollutants of both gaseous and aquatic effluents. Additional hinder to a BAT-IPPC complete procedure are hazardous or uneconomical byproducts of the IPPC processes and significant auxiliary costs f...

[Integrated prevention and control strategy for dengue in Mesoamerica].

Science.gov (United States)

Gómez-Dantés, Héctor; San Martín, José Luis; Danis-Lozano, Rogelio; Manrique-Saide, Pablo

2011-01-01

Dengue in the Americas is a public health problem in ascent. The control strategies have not been effective when sustained in the intensive use of insecticides and poor community participation. The Mesoamerican Initiative for the Prevention and the Integrated Control of Dengue synthesizes the works generated by the Integrated Strategy of the Pan-American Health Organization (PAHO) and the risks stratification strategy designed by the countries of the Mesoamerican region. The objective is to progressively reduce the incidence of dengue cases until a 50% reduction is reached over a five years period. This document describes the elements for the risk stratification, the activities for prevention and control organized by levels of intensity and frequency and the indicators used to pursuit the objectives. To face the dispersion of the problem a concentration of efforts for control in the areas of greater risk is presented; the opportunity in the detection of cases is highlighted to tackle the fast dissemination of the infection; focus on the most productive breeding sites is proposed to battle against the vast dissemination of the breeding sites; and the severity of the infection must be addressed by capable clinical human resources. This strategy was designed along with the national representatives of the control programs to create master plans that provided the basis for the integrated prevention and control of dengue in the Mesoamerican region.

Pollution prevention at ports: clearing the air

International Nuclear Information System (INIS)

Bailey, Diane; Solomon, Gina

2004-01-01

Seaports are major hubs of economic activity and of environmental pollution in coastal urban areas. Due to increasing global trade, transport of goods through ports has been steadily increasing and will likely continue to increase in the future. Evaluating air pollution impacts of ports requires consideration of numerous sources, including marine vessels, trucks, locomotives, and off-road equipment used for moving cargo. The air quality impacts of ports are significant, with particularly large emissions of diesel exhaust, particulate matter, and nitrogen oxides. The health effects of these air pollutants to residents of local communities include asthma, other respiratory diseases, cardiovascular disease, lung cancer, and premature mortality. In children, there are links with asthma, bronchitis, missed school days, and emergency room visits. The significance of these environmental health impacts requires aggressive efforts to mitigate the problem. Approaches to mitigation encompass a range of possibilities from currently available, low-cost approaches, to more significant investments for cleaner air. Examples of the former include restrictions on truck idling and the use of low-sulfur diesel fuel; the latter includes shore-side power for docked ships, and alternative fuels. A precautionary approach to port-related air pollution would encourage local production of goods in order to reduce marine traffic, greener design for new terminals, and state-of-the art approaches to emissions-control that have been successfully demonstrated at ports throughout the world

Multi-objective group scheduling optimization integrated with preventive maintenance

Science.gov (United States)

Liao, Wenzhu; Zhang, Xiufang; Jiang, Min

2017-11-01

This article proposes a single-machine-based integration model to meet the requirements of production scheduling and preventive maintenance in group production. To describe the production for identical/similar and different jobs, this integrated model considers the learning and forgetting effects. Based on machine degradation, the deterioration effect is also considered. Moreover, perfect maintenance and minimal repair are adopted in this integrated model. The multi-objective of minimizing total completion time and maintenance cost is taken to meet the dual requirements of delivery date and cost. Finally, a genetic algorithm is developed to solve this optimization model, and the computation results demonstrate that this integrated model is effective and reliable.

GM`s PICOS initiative on resource conservation and pollution prevention: Greening the supply chain

Energy Technology Data Exchange (ETDEWEB)

Pritchett, T. [General Motors Corp., Detroit, MI (United States)

1997-12-31

This paper is comprised of reprints of several related articles from business publications. The first article, on supply-side economics, describes efforts by General Motors to cut costs by encouraging suppliers to reduce the environmental impacts of their products. The PICOS{trademark} program of General Motors helps industrial identify and implement energy efficiency and pollution prevention projects that lower operating costs while reducing emissions linked to global climate change. The second article also describes the program, focusing on aspects of global competition.

GeoMedStat: an integrated spatial surveillance system to track air pollution and associated healthcare events

Directory of Open Access Journals (Sweden)

Fazlay S. Faruque

2014-12-01

Full Text Available Air pollutants, such as particulate matter with a diameter ≤2.5 microns (PM2.5 and ozone (O3, are known to exacerbate asthma and other respiratory diseases. An integrated surveillance system that tracks such air pollutants and associated disease incidence can assist in risk assessment, healthcare preparedness and public awareness. However, the implementation of such an integrated environmental health surveillance system is a challenge due to the disparate sources of many types of data and the implementation becomes even more complicated for a spatial and real-time system due to lack of standardised technological components and data incompatibility. In addition, accessing and utilising health data that are considered as Protected Health Information (PHI require maintaining stringent protocols, which have to be supported by the system. This paper aims to illustrate the development of a spatial surveillance system (GeoMedStat that is capable of tracking daily environmental pollutants along with both daily and historical patient encounter data. It utilises satellite data and the groundmonitor data from the US National Aeronautics and Space Administration (NASA and the US Environemental Protection Agenecy (EPA, rspectively as inputs estimating air pollutants and is linked to hospital information systems for accessing chief complaints and disease classification codes. The components, developmental methods, functionality of GeoMedStat and its use as a real-time environmental health surveillance system for asthma and other respiratory syndromes in connection with with PM2.5 and ozone are described. It is expected that the framework presented will serve as an example to others developing real-time spatial surveillance systems for pollutants and hospital visits.

Investment strategy for sustainable society by development of regional economies and prevention of industrial pollutions in Japanese manufacturing sectors

International Nuclear Information System (INIS)

Sueyoshi, Toshiyuki; Goto, Mika

2014-01-01

A balance between industrial pollution prevention and economic growth becomes a world-wide issue to develop a sustainable society in many industrial nations. To discuss the issue, this study proposes a new use of DEA environmental assessment to determine how to effectively allocate capital for developing regional industries. The amount of capital is used to invest for technology innovation for both local economic growth and environmental protection. In this study, the proposed approach separates outputs into desirable and undesirable categories. Inputs are also separated into two categories, one of which indicates an amount of investment on capital assets. The other category is used for production activities. The proposed approach unifies them by two disposability concepts. This study has evaluated the performance of manufacturing industries in 47 prefectures (local government units in Japan) by Unified Efficiency under Natural disposability (UEN), Unified Efficiency under Managerial disposability (UEM) and Unified Efficiency under Natural and Managerial disposability (UENM). The UENM is further separated into its two cases: with and without a possible occurrence on desirable congestion, or technology innovation, on undesirable outputs. This study has empirically confirmed that Japanese manufacturing industries need to make their efforts to reduce greenhouse gas emissions and air pollution substances by investing in technology innovation. Furthermore, most of economic activities are currently located at metropolitan regions (e.g., Tokyo) in Japan. To develop a sustainable society, Japan needs to allocate capital into regions with a high level of investment effectiveness by shifting the manufacturing industries from the metropolitan regions to much promising local areas identified in this study. Such a shift, along with technology innovation, makes it possible to reduce air pollutions in the entire Japan by balancing economic growth and pollution prevention. This

Integrated forest management to prevent wildfires under Mediterranean environments

Directory of Open Access Journals (Sweden)

Piermaria Corona

2015-02-01

Full Text Available This review presents a multidisciplinary framework for integrating the ecological, regulatory, procedural and technical aspects of forest management for fires prevention under Mediterranean environments. The aims are to: i provide a foreground of wildfire scenario; ii illustrate the theoretical background of forest fuel management; iii describe the available fuel management techniques and mechanical operations for fire prevention in forest and wildland-urban interfaces, with exemplification of case-studies; iv allocate fire prevention activities under the hierarchy of forest planning. The review is conceived as an outline commentary discussion targeted to professionals, technicians and government personnel involved in forestry and environmental management.

Methodologies of health impact assessment as part of an integrated approach to reduce effects of air pollution

Energy Technology Data Exchange (ETDEWEB)

Aunan, K; Seip, H M

1995-12-01

Quantification of average frequencies of health effects on a population level is an essential part of an integrated assessment of pollution effects. Epidemiological studies seem to provide the best basis for such estimates. This paper gives an introduction to a methodology for health impact assessment and also the results from selected parts of a case study in Hungary. This case study is aimed at testing and improving the methodology for integrated assessment and focuses on energy production and consumption and implications for air pollution. Using monitoring data from Budapest, the paper gives estimates of excess frequencies of respiratory illness, mortality and other health end-points. For a number of health end-points, particles probably may serve as a good indicator component. Stochastic simulation is used to illustrate the uncertainties imbedded in the exposure-response function applied. The paper uses the ``bottom up approach`` to find cost-effective abatement strategies against pollution damages, where specific abatement measures such as emission standards for vehicles are explored in detail. It is concluded that in spite of large uncertainties in every step of the analysis, an integrated assessment of costs and benefits of different abatement measures is valuable as it clarifies the main objectives of an abatement policy and explicitly describes the adverse impacts of different activities and their relative importance. 46 refs., 11 figs., 2 tabs.

Convention on the Prevention of Marine Pollution by Dumping of Wastes and Other Matter

International Nuclear Information System (INIS)

1974-01-01

The Convention on the Prevention of Marine Pollution by Dumping of Wastes and Other Matter was drawn up at the Inter-Governmental Conference on the Dumping of Wastes at Sea, held in London from 30 October to 10 November 1972. The Governments of Mexico, the Union of Soviet Socialist Republics, the United Kingdom of Great Britain and Northern Ireland and the United States of America are the Depository Governments for instruments of ratification of, and accession to, the Convention, pursuant to Articles XVII and XVIII respectively [es

Convention on the Prevention of Marine Pollution by Dumping of Wastes and Other Matter

International Nuclear Information System (INIS)

1974-01-01

The Convention on the Prevention of Marine Pollution by Dumping of Wastes and Other Matter was drawn up at the Inter-Governmental Conference on the Dumping of Wastes at Sea, held in London from 30 October to 10 November 1972. The Governments of Mexico, the Union of Soviet Socialist Republics, the United Kingdom of Great Britain and Northern Ireland and the United States of America are the Depository Governments for instruments of ratification of, and accession to, the Convention, pursuant to Articles XVII and XVIII respectively

Environmental implementation plan: Chapter 5, Chemical management, pollution prevention and other compliance programs

International Nuclear Information System (INIS)

Peterson, G.L.

1993-01-01

Compliance with environmental regulations and US Department of Energy Orders (DOE) relating to environmental protection is an important part of SRS's program. Over the past few years, the number of environmental regulations has increased. The strategy to comply with new and existing environmental regulations and DOE orders is described in chapter two. In this chapter, the following environmental programs are described: Toxic Substances Control Act (TSCA); Federal Insecticide, Fungicide, and Rodenticide Act (FIFRA); Emergency Planning and Community Right-to-Know Act (EPCRA); and SPCC/BMP/Pollution Prevention Plans;The implementation section identifies issues and those responsible to achieve defined objectives

Full report: Assessment and opportunity identification of energy efficient pollution prevention technologies and processes

Energy Technology Data Exchange (ETDEWEB)

1994-11-01

US industry produces about 12 billion tons of waste a year, or two-thirds of the waste generated in the US. The costs of handling and disposing of these wastes are significant, estimated to be between $25 and $43 billion in 1991, and represent an increase of 66% since 1986. US industry also uses about one-third of all energy consumed in the nation, which adds to the environmental burden. Industrial wastes affect the environmental well-being of the nation and, because of their growing costs, the competitive abilities of US industry. As part of a national effort to reduce industrial wastes, the US Congress passed the Energy Policy Act (EPAct, P.L. 102-486). Section 2108, subsections (b) and (c), of EPAct requires the Department of Energy (DOE) to identify opportunities to demonstrate energy efficient pollution prevention technologies and processes; to assess their availability and the energy, environmental, and cost effects of such technologies; and to report the results. Work for this report clearly pointed to two things, that there is insufficient data on wastes and that there is great breadth and diversity in the US industrial sector. This report identifies: information currently available on industrial sector waste streams, opportunities for demonstration of energy efficient pollution prevention technologies in two industries that produce significant amounts of waste--chemicals and petroleum, characteristics of waste reducing and energy saving technologies identifiable in the public literature, and potential barriers to adoption of waste reducing technologies by industry.

The Federal Air Pollution Program.

Science.gov (United States)

National Air Pollution Control Administration (DHEW), Washington, DC.

Described is the Federal air pollution program as it was in 1967. The booklet is divided into these major topics: History of the Federal Program; Research; Assistance to State and Local Governments; Abatement and Prevention of Air Pollution; Control of Motor Vehicle Pollution; Information and Education; and Conclusion. Federal legislation has…

Air pollution in eastern Asia an integrated perspective

CERN Document Server

Wang, Xuemei; Brasseur, Guy

2017-01-01

This book, written by an international group of experts from China, Europe and the USA, presents a broad and comprehensive analysis of the chemical and meteorological processes responsible for the formation of air pollutants in eastern Asia, and in particular for the development of severe pollution episodes observed primarily during winter in the northeastern part of China. With the rapid population growth, economic development and urbanization occurring in Asia, air pollution has become a major environmental problem in this part of the world. The book is organized around six distinct parts. The first part of the volume offers a general perspective on issues related to air pollution including persistent haze events in eastern and southern Asia. The second part presents an overview of air pollution sources (i.e., anthropogenic and biomass burning sources). The third part analyzes in-situ observations of chemical species in China, while the fourth part focuses on space observations of gas-phase and aerosol spec...

Irradiance Impact on Pollution by Integrating Nephelometer Measurements

Directory of Open Access Journals (Sweden)

Maria Rita Perrone

2015-12-01

Full Text Available Three-wavelength integrating nephelometer measurements combined with short- (SW and long-wave (LW irradiance measurements were used to investigate the irradiance effects on the daily evolution of the particulate matter (PM at the ground level, and contribute to the characterization of the land–atmosphere interaction in pollution dispersal. The integrating nephelometer measurements have allowed characterizing the daily changes of the PM optical and microphysical properties by the aerosol scattering coefficient (σp and the scattering Ångström coefficient (å. We found that on a daily basis σp reached the minimum values when the irradiance reached the maximum values, since the convective motions, which favor the particle dispersion at the surface, increase with the irradiance. The å value, which is commonly used as qualitative indicator of the dominant particle size, has allowed evaluating the irradiance effects on the mean particle size distribution at the surface and revealed that the irradiance increase favors mainly the dispersion of the ground-level fine particles. Particle size-distribution measurements supported the last comment. Measurements were performed from 4 to 10 May 2015 when the study site was affected by a Saharan dust outbreak, to also evaluate the impact of long-range transported particles on the daily evolution of the ground-level particle’s properties and the SW and LW irradiance.

Integration of fall prevention into state policy in Connecticut.

Science.gov (United States)

Murphy, Terrence E; Baker, Dorothy I; Leo-Summers, Linda S; Bianco, Luann; Gottschalk, Margaret; Acampora, Denise; King, Mary B

2013-06-01

To describe the ongoing efforts of the Connecticut Collaboration for Fall Prevention (CCFP) to move evidence regarding fall prevention into clinical practice and state policy. A university-based team developed methods of networking with existing statewide organizations to influence clinical practice and state policy. We describe steps taken that led to funding and legislation of fall prevention efforts in the state of Connecticut. We summarize CCFP's direct outreach by tabulating the educational sessions delivered and the numbers and types of clinical care providers that were trained. Community organizations that had sustained clinical practices incorporating evidence-based fall prevention were subsequently funded through mini-grants to develop innovative interventional activities. These mini-grants targeted specific subpopulations of older persons at high risk for falls. Building collaborative relationships with existing stakeholders and care providers throughout the state, CCFP continues to facilitate the integration of evidence-based fall prevention into clinical practice and state-funded policy using strategies that may be useful to others.

L'IIASA and the integrated simulation of the trans-border atmospheric pollution assessment and evaluation; L'IIASA et la modelisation integree de la pollution atmospherique transfrontiere. Bilan et evaluation

Energy Technology Data Exchange (ETDEWEB)

Soleille, S.; Brignon, J.M.; Farret, R.; Landrieu, G.; Le Gall, A.C.; Rouil, L

2003-09-15

The RAINS model is an integrated evaluation model for many pollutants and many effects, developed by he IIASA. This model studies the emissions of 4 atmospheric pollutants (nitrogen oxides, sulfur oxides, ammonium and volatile organic compounds) and the necessary costs to reduce them and the dispersion of these pollutants and their effects (tropospheric ozone formation, acidification and eutrophication). The model can be used in activities scenario mode (energy, agriculture, transports...) to calculate the emissions and their effects or in optimization mode to calculate strategies of emissions control from environmental constraints. (A.L.B.)

Industrial Pollution Regulation in the EU and in Macedonia, Serbia And Croatia

Directory of Open Access Journals (Sweden)

Aleksandar Chavleski

2013-09-01

Full Text Available Industrial pollution control has substantial impact in the protection of the environment. In the European Union, there’s vast legislation in this field consisting mainly of the Directive on industrial emissions of 2010 aimed at consolidating the so far existing legislation in this field. The new Directive on industrial emissions aims to establish an integrated prevention and control of the pollution arising from industrial activities and it lays down rules designed to prevent or, where that is not practicable, to reduce emissions into air, water and land and to prevent the generation of waste, in order to achieve a high level of protection of the environment taken as a whole. Macedonia, Serbia and Croatia have made significant progress in this field in the recent years as part of their obligations under the Stabilization and Association Process. The purpose of this particular article is to evaluate the degree of alignment and implementation of the environmental legislation in this particular area with the legislation of EU as well its practical application, and to identify the existing deficiencies and necessary steps for action

Violence prevention in special education schools - an integrated practice?

Science.gov (United States)

Pihl, Patricia; Grytnes, Regine; Andersen, Lars Peter S

2018-06-01

Research has shown that employees in special education settings are at high risk for work-related threats and violence. Previous research has not yet been able to identify the essential components of training programs that offer protection from work-related threats and violence. Therefore, the aim of this study was to explore how employees in special education schools deal with prevention of work-related threats and violence. Group interviews were conducted with 14 employees working at 5 special education schools. Results show that employees use a wide range of prevention strategies drawing on specific violence prevention techniques as well as professional pedagogical approaches. We propose that the prevention of threats and violence in special education schools can be understood as an integrated pedagogical practice operating on three interrelated levels. Copyright © 2018 Elsevier Ltd. All rights reserved.

Coral-zooxanthellae meta-transcriptomics reveals integrated response to pollutant stress.

Science.gov (United States)

Gust, Kurt A; Najar, Fares Z; Habib, Tanwir; Lotufo, Guilherme R; Piggot, Alan M; Fouke, Bruce W; Laird, Jennifer G; Wilbanks, Mitchell S; Rawat, Arun; Indest, Karl J; Roe, Bruce A; Perkins, Edward J

2014-07-12

Corals represent symbiotic meta-organisms that require harmonization among the coral animal, photosynthetic zooxanthellae and associated microbes to survive environmental stresses. We investigated integrated-responses among coral and zooxanthellae in the scleractinian coral Acropora formosa in response to an emerging marine pollutant, the munitions constituent, 1,3,5-trinitro-1,3,5 triazine (RDX; 5 day exposures to 0 (control), 0.5, 0.9, 1.8, 3.7, and 7.2 mg/L, measured in seawater). RDX accumulated readily in coral soft tissues with bioconcentration factors ranging from 1.1 to 1.5. Next-generation sequencing of a normalized meta-transcriptomic library developed for the eukaryotic components of the A. formosa coral holobiont was leveraged to conduct microarray-based global transcript expression analysis of integrated coral/zooxanthellae responses to the RDX exposure. Total differentially expressed transcripts (DET) increased with increasing RDX exposure concentrations as did the proportion of zooxanthellae DET relative to the coral animal. Transcriptional responses in the coral demonstrated higher sensitivity to RDX compared to zooxanthellae where increased expression of gene transcripts coding xenobiotic detoxification mechanisms (i.e. cytochrome P450 and UDP glucuronosyltransferase 2 family) were initiated at the lowest exposure concentration. Increased expression of these detoxification mechanisms was sustained at higher RDX concentrations as well as production of a physical barrier to exposure through a 40% increase in mucocyte density at the maximum RDX exposure. At and above the 1.8 mg/L exposure concentration, DET coding for genes involved in central energy metabolism, including photosynthesis, glycolysis and electron-transport functions, were decreased in zooxanthellae although preliminary data indicated that zooxanthellae densities were not affected. In contrast, significantly increased transcript expression for genes involved in cellular energy production

Towards a multidisciplinary and integrated strategy in the assessment of adverse health effects related to air pollution: The case study of Cracow (Poland) and asthma

International Nuclear Information System (INIS)

Oudinet, Jean-Paul; Meline, Julie; Chelmicki, Wojciech; Sanak, Marek; Magdalena, Dutsch-Wicherek; Besancenot, Jean-Pierre; Wicherek, Stanislas; Julien-Laferriere, Bertrand; Gilg, Jean-Paul; Geroyannis, Helene; Szczeklik, Andrew; Krzemien, Kazimierz

2006-01-01

Complex interaction between anthropogenic activities, air quality and human health in urban areas, such as in Cracow sustains the need for the development of an interdisciplinary and integrated risk-assessment methodology. In such purpose, we propose a pilot study performed on asthmatics and based on a combined use of a biomarker, such as metallothionein 2A (MT-2A) in the characterization of human exposure to one or a mixture of pollutants and of Geographical Information Systems (G.I.S.) which integrates climatic and urban anthropogenic parameters in the assessment of spatio-temporal dispersion of air pollutants. Considering global incidence of air pollution on asthma and on peripheral blood lymphocytes MT-2A expression should provide a complementary information on biological risks linked to urban anthropogenic activities. Such study would help for the establishment of a sustainable development in urban areas that can maintain the integrity of air quality and preserve human health. - An integrative risk methodology based on both geographic and molecular biological approaches is proposed for the assessment of asthmatics exposure to urban air pollution

Gains of integrating sector-wise pollution regulation

DEFF Research Database (Denmark)

Jacobsen, Lars Bo; Nielsen, Max; Nielsen, Rasmus

2016-01-01

This paper extends the Orani-G Computable General Equilibrium model with an externality market. The externality market is modelled with a limited number of pollution permits that are traded between representative firms in different sectors. The model is applied to identify the gains of a common...... of introducing more coherent regulatory frameworks that include all polluters under the same regulatory system....

Integrated preventive maintenance and production decisions for imperfect processes

International Nuclear Information System (INIS)

Nourelfath, Mustapha; Nahas, Nabil; Ben-Daya, Mohamed

2016-01-01

This paper integrates production, maintenance, and quality for an imperfect process in a multi-period multi-product capacitated lot-sizing context. The production system is modeled as an imperfect machine, whose the status is considered to be either in-control or out-of-control. When the machine is out of control, it produces a fraction of nonconforming items. During each period, this machine is inspected and imperfect preventive maintenance activities are simultaneously performed to reduce its age, proportional to the preventive maintenance level. The objective is to minimize the total cost, while satisfying the demand for all products. Our optimization model allows for a joint selection of the optimal values of production plan, and the maintenance policy, while taking into account quality related costs. A solution algorithm is developed and illustrative numerical examples are presented. It is found that the increase in PM level leads to reductions in quality control costs. Furthermore, if the cost of performing PM is high to the point where it is not compensated for by reductions in the quality related costs, then performing PM is not justifiable. Finally, using non-periodic preventive maintenance with the possibility of different preventive maintenance levels may result in an improvement of the total cost. - Highlights: • We integrate production, maintenance, and quality. • We evaluate all the expected costs. • Our model allows for a joint selection of the optimal values. • A solution algorithm is developed. • Increasing PM level will decrease quality control costs.

Integral Design Methodology of Photocatalytic Reactors for Air Pollution Remediation

Directory of Open Access Journals (Sweden)

Claudio Passalía

2017-06-01

Full Text Available An integral reactor design methodology was developed to address the optimal design of photocatalytic wall reactors to be used in air pollution control. For a target pollutant to be eliminated from an air stream, the proposed methodology is initiated with a mechanistic derived reaction rate. The determination of intrinsic kinetic parameters is associated with the use of a simple geometry laboratory scale reactor, operation under kinetic control and a uniform incident radiation flux, which allows computing the local superficial rate of photon absorption. Thus, a simple model can describe the mass balance and a solution may be obtained. The kinetic parameters may be estimated by the combination of the mathematical model and the experimental results. The validated intrinsic kinetics obtained may be directly used in the scaling-up of any reactor configuration and size. The bench scale reactor may require the use of complex computational software to obtain the fields of velocity, radiation absorption and species concentration. The complete methodology was successfully applied to the elimination of airborne formaldehyde. The kinetic parameters were determined in a flat plate reactor, whilst a bench scale corrugated wall reactor was used to illustrate the scaling-up methodology. In addition, an optimal folding angle of the corrugated reactor was found using computational fluid dynamics tools.

Identifying inequitable exposure to toxic air pollution in racialized and low-income neighbourhoods to support pollution prevention

Directory of Open Access Journals (Sweden)

Suzanne Kershaw

2013-05-01

Full Text Available Numerous environmental justice studies have confirmed a relationship between population characteristics such as low-income or minority status and the location of environmental health hazards. However, studies of the health risks from exposure to harmful substances often do not consider their toxicological characteristics. We used two different methods, the unit-hazard and the distance-based approach, to evaluate demographic and socio-economic characteristics of the population residing near industrial facilities in the City of Toronto, Canada. In addition to the mass of air emissions obtained from the national pollutant release inventory (NPRI, we also considered their toxicity using toxic equivalency potential (TEP scores. Results from the unit-hazard approach indicate no significant difference in the proportion of low-income individuals living in host versus non-host census tracts (t(107 = 0.3, P = 0.735. However, using the distance-based approach, the proportion of low-income individuals was significantly higher (+5.1%, t(522 = 6.0, P <0.001 in host tracts, while the indicator for “racialized” communities (“visible minority” was 16.1% greater (t(521 = 7.2, P <0.001 within 2 km of a NPRI facility. When the most toxic facilities by non-carcinogenic TEP score were selected, the rate of visible minorities living near the most toxic NPRI facilities was significantly higher (+12.9%, t(352 = 3.5, P = 0.001 than near all other NPRI facilities. TEP scores were also used to identify areas in Toronto that face a double burden of poverty and air toxics exposure in order to prioritise pollution prevention.

Development and application of an integrated evaluation framework for preventive safety applications

NARCIS (Netherlands)

Scholliers, J.; Joshi, S.; Gemou, M.; Hendriks, F.; Ljung Aust, M.; Luoma, J.; Netto, M.; Engstrom, J.; Leanderson Olsson, S.; Kutzner, R.; Tango, F.; Amditis, A.J.; Blosseville, J.M.; Bekiaris, E.

2011-01-01

Preventive safety functions help drivers avoid or mitigate accidents. No quantitative methods have been available to evaluate the safety impact of these systems. This paper describes a framework for the assessment of preventive and active safety functions, which integrates procedures for technical

Hydrocarbons and air pollution

International Nuclear Information System (INIS)

Herz, O.

1992-01-01

This paper shows the influence of hydrocarbons vapors, emitted by transports or by volatile solvents using, on air pollution. Hydrocarbons are the principal precursors of photochemical pollution. After a brief introduction on atmospheric chemistry and photochemical reactions, the author describes the french prevention program against hydrocarbons emissions. In the last chapter, informations on international or european community programs for photochemical pollution study are given. 5 figs., 10 tabs

Integrated Watershed Pollution Control at Wujingang Canal, China

Science.gov (United States)

Zheng, Z.; Yang, X.; Luo, X.

2012-04-01

With a drainage area of 400 square kilometers, Wujingang Canal is located at the economically developed Yangtz Delta of eastern China. As a major tributary, the canal contributes a significant amount of pollutant load to the Lake Tai. Over the past many years, water quality of the canal and its tributaries could not meet the lowest Category V of Chinese surface water quality standard, indicating that its water is not suitable for the purposes of irrigation or scenic views. Major pollution sources in the watershed include industries, residential households, agriculture, fishery, and animal feedlot operations. A comprehensive plan with a budget of 2 billion RMB for the Wujingang watershed pollution control was developed in 2008 and has been implemented progressively ever since. Major components of the plan include: (1) advanced treatment of wastewater from industries and municipal sewage plants for further removal of nitrogen and phosphorous; (2) industrial wastewater reuse; (3) contiguous treatment of sewage from rural residential households with cost-effective technologies such as tower ecofilter system; (4) recycling of rural wastes to generate high-value added products using technologies such as multi-phase anaerobic co-digestion; and (5) making full use of the local landscape and configuring physical, chemical, and biological pollutant treatment structures to build the "clean river network" for treatment of mildly polluted agricultural discharge and surface runoff. Through the implementation of the above measures, water quality of the Wujingang Canal and its tributaries is expected to improve to meet Category IV of Chinese surface water quality standard by 2012, and Category III standard by 2020. Keywords watershed pollution control, non-point source pollution, rural sewage, rural waste, Lake Tai

Groundwater pollution: are we monitoring appropriate parameters?

CSIR Research Space (South Africa)

Tredoux, G

2004-01-01

Full Text Available Groundwater pollution is a worldwide phenomenon with potentially disastrous consequences. Prevention of pollution is the ideal approach. However, in practice groundwater quality monitoring is the main tool for timely detection of pollutants...

Atmospheric Pollution: Its Origins and Prevention.

Science.gov (United States)

Meetham, A. R.

Although atmospheric pollution can be reduced or eliminated in many different ways, each way involves questions of economics, the time factor, availability of materials, priority over other urgent reforms, and individual and social psychology. To provide a basis for consideration of these questions, this book gives information not only about the…

High-Resolution Modelling of Health Impacts from Air Pollution for Denmark using the Integrated Model System EVA

Science.gov (United States)

Brandt, Jørgen; Andersen, Mikael S.; Bønløkke, Jakob; Christensen, Jesper H.; Hansen, Kaj M.; Hertel, Ole; Im, Ulas; Jensen, Steen S.; Ketzel, Matthias; Nielsen, Ole-Kenneth; Plejdrup, Marlene S.; Sigsgaard, Torben; Geels, Camilla

2015-04-01

We have developed an integrated health impact assessment system EVA (Economic Valuation of Air pollution; Brandt et al., 2013a; 2013b), based on the impact-pathway chain, to assess the health impacts and health-related economic externalities of air pollution resulting from specific emission sources or sectors. The system is used to support policymaking with respect to emission control. The EVA system has previously been used to assess the health impacts based on results from a regional model DEHM (the Danish Eulerian Hemispheric Model; Brandt et al., 2012). In this study we have used a coupling of two chemistry transport models to calculate the air pollution concentration at different scales; the DEHM model to calculate the air pollution levels with a resolution down to 5.6 km x 5.6 km and the UBM model (Urban Background Model ; Berkowicz, 2000; Brandt et al., 2001) to further calculate the air pollution at 1 km x 1 km resolution for Denmark using results from DEHM as boundary conditions. Both the emission data based on the SPREAD model (Plejdrup and Gyldenkærne, 2011) as well as the population density has been represented in the model system with the same high resolution. The new developments of the integrated model system will be presented as well as results for health impacts and related external costs over the years 2006-2014 for Denmark. Furthermore, a sensitivity study of the health impact using coarse and fine resolutions in the model system has been carried out to evaluate the effect of improved description of the geographical population distribution with respect to location of local emissions. References Berkowicz, R., 2000. A Simple Model for Urban Background Pollution. Environmental Monitoring and Assessment, 65, 1/2, 259-267. Brandt, J., J. H. Christensen, L. M. Frohn, F. Palmgren, R. Berkowicz and Z. Zlatev, 2001: "Operational air pollution forecasts from European to local scale". Atmospheric Environment, Vol. 35, Sup. No. 1, pp. S91-S98, 2001 Brandt

Air pollution and respiratory illness

Energy Technology Data Exchange (ETDEWEB)

Indra, G. [DIET, Uttamasolapuram, Salem (India)

2005-07-01

This presentation provides an overview of air pollution and impacts on public health. It provides a definition of pollution according to the Oxford English dictionary and categorizes the different types of pollution according to air, water, land and noise. It discusses air pollution and its pollutants (gaseous and particulate pollutants) as well as the diameter of the pollutant (dust, smoke, and gas). The paper also illustrates the formation of acid rain and discusses the amount of pollutants in the atmosphere per year. It presents occupational diseases, discusses radio active pollutants, respiratory illnesses as well as pollution prevention and control. The paper concluded that more research is needed to obtain information on ways to reduce the quantity of pollutants being discharged from special processes. 3 refs., 2 figs., 2 tabs.

A new theory and method of preventing harmful waste landfill from pollution to groundwater

International Nuclear Information System (INIS)

Liu Changli; Zhang Yun; Song Shuhong; Hou Hongbing

2006-01-01

It is limited in conventional Soil Liner theory of waste landfill, we must update the theory and the calculational methods must be broke, so that the cost of waste landfill could be reduced in wide scope, this is important to develop economy and environment in sustaining rate. It is an innovation in the theory of the pollution control in the waste landfill groundwater through translated the theories of 'excluding infiltrate to groundwater' into 'insulating waste, allowing water into groundwater', the theory of waste landfill from pollution to groundwater came true. Clayey Soil not only can prevent seepage, but also can obstruct waste. If we can make use of its filtration adequately, just as using experimentation in laboratory to research filtration capability, calculation, we could made new testing technique and calculated technique of liner parameters. This paper take an example of which calculate to liner parameters, such as 'filtration capability' and 'adequacy thickness of effective liner', and make a programming of landfill site by this theory and method in Beijing plain. (authors)

Measures to prevent oil pollution in oceans, and their preservation effect; Kaiyo no abura osen no boshi taisaku to hozen koka ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Shinoda, T; Fukuchi, N; Fujii, H [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Sato, S

1996-04-10

It was intended to confirm, based on various problems surrounding oil flow-out accidents, that oil fences whose use is first considered when an oil flow-out accident occurs cause oil leakage due to oil pass-through phenomenon as the largest defect in performance of oil fences. Therefore, oil fence performance was analyzed by using a simulation. Furthermore, several types of diffusion prevention and avoidance measures, and combinations thereof were evaluated by using multi-criteria analysis. It was also elucidated how recognitions on the importance of methods to prevent oil pollution differ depending on standpoints. Difference in oil flow-out prevention performance of oil fences due to variation in tidal currents was made clear by combining a diffusion simulation using the finite element method with the prevention performance of oil fences relative to the tidal currents. In areas with no good hydrographic conditions where pollution spreads rapidly, it is necessary to suppress oil diffusion by extending oil fences double or triple, and using gelling agents. 4 refs., 8 figs.

Geodiametris: an integrated geoinformatic approach for monitoring land pollution from the disposal of olive oil mill wastes

Science.gov (United States)

Alexakis, Dimitrios D.; Sarris, Apostolos; Papadopoulos, Nikos; Soupios, Pantelis; Doula, Maria; Cavvadias, Victor

2014-08-01

The olive-oil industry is one of the most important sectors of agricultural production in Greece, which is the third in olive-oil production country worldwide. Olive oil mill wastes (OOMW) constitute a major factor in pollution in olivegrowing regions and an important problem to be solved for the agricultural industry. The olive-oil mill wastes are normally deposited at tanks, or directly in the soil or even on adjacent torrents, rivers and lakes posing a high risk to the environmental pollution and the community health. GEODIAMETRIS project aspires to develop integrated geoinformatic methodologies for performing monitoring of land pollution from the disposal of OOMW in the island of Crete -Greece. These methodologies integrate GPS surveys, satellite remote sensing and risk assessment analysis in GIS environment, application of in situ and laboratory geophysical methodologies as well as soil and water physicochemical analysis. Concerning project's preliminary results, all the operating OOMW areas located in Crete have been already registered through extensive GPS field campaigns. Their spatial and attribute information has been stored in an integrated GIS database and an overall OOMW spectral signature database has been constructed through the analysis of multi-temporal Landsat-8 OLI satellite images. In addition, a specific OOMW area located in Alikianos village (Chania-Crete) has been selected as one of the main case study areas. Various geophysical methodologies, such as Electrical Resistivity Tomography, Induced Polarization, multifrequency electromagnetic, Self Potential measurements and Ground Penetrating Radar have been already implemented. Soil as well as liquid samples have been collected for performing physico-chemical analysis. The preliminary results have already contributed to the gradual development of an integrated environmental monitoring tool for studying and understanding environmental degradation from the disposal of OOMW.

Peri-Urbanism in Globalizing India: A Study of Pollution, Health and Community Awareness.

Science.gov (United States)

Waldman, Linda; Bisht, Ramila; Saharia, Rajashree; Kapoor, Abhinav; Rizvi, Bushra; Hamid, Yasir; Arora, Meghana; Chopra, Ima; Sawansi, Kumud T; Priya, Ritu; Marshall, Fiona

2017-08-30

This paper examines the intersection between environmental pollution and people's acknowledgements of, and responses to, health issues in Karhera, a former agricultural village situated between the rapidly expanding cities of New Delhi (India's capital) and Ghaziabad (an industrial district in Uttar Pradesh). A relational place-based view is integrated with an interpretive approach, highlighting the significance of place, people's emic experiences, and the creation of meaning through social interactions. Research included surveying 1788 households, in-depth interviews, participatory mapping exercises, and a review of media articles on environment, pollution, and health. Karhera experiences both domestic pollution, through the use of domestic waste water, or gandapani , for vegetable irrigation, and industrial pollution through factories' emissions into both the air and water. The paper shows that there is no uniform articulation of any environment/health threats associated with gandapani . Some people take preventative actions to avoid exposure while others do not acknowledge health implications. By contrast, industrial pollution is widely noted and frequently commented upon, but little collective action addresses this. The paper explores how the characteristics of Karhera, its heterogeneous population, diverse forms of environmental pollution, and broader governance processes, limit the potential for citizen action against pollution.

DIDEM - An integrated model for comparative health damage costs calculation of air pollution

Science.gov (United States)

Ravina, Marco; Panepinto, Deborah; Zanetti, Maria Chiara

2018-01-01

Air pollution represents a continuous hazard to human health. Administration, companies and population need efficient indicators of the possible effects given by a change in decision, strategy or habit. The monetary quantification of health effects of air pollution through the definition of external costs is increasingly recognized as a useful indicator to support decision and information at all levels. The development of modelling tools for the calculation of external costs can provide support to analysts in the development of consistent and comparable assessments. In this paper, the DIATI Dispersion and Externalities Model (DIDEM) is presented. The DIDEM model calculates the delta-external costs of air pollution comparing two alternative emission scenarios. This tool integrates CALPUFF's advanced dispersion modelling with the latest WHO recommendations on concentration-response functions. The model is based on the impact pathway method. It was designed to work with a fine spatial resolution and a local or national geographic scope. The modular structure allows users to input their own data sets. The DIDEM model was tested on a real case study, represented by a comparative analysis of the district heating system in Turin, Italy. Additional advantages and drawbacks of the tool are discussed in the paper. A comparison with other existing models worldwide is reported.

Research plan for integrated ecosystem and pollutant monitoring at remote wilderness study sites

International Nuclear Information System (INIS)

Bruns, D.A.; Wiersma, G.B.

1988-03-01

This research plan outlines an approach to the measurement of pollutants and ecosystem parameters at remote, high-elevation, wilderness study sites. A multimedia, systems approach to environmental monitoring is emphasized. The primary purpose of the research is to apply and field test a technical report entitled ''Guidelines for measuring the physical, chemical, and biological condition of wilderness ecosystems.'' This document intended to provide Federal Land Managers with information to establish environmental monitoring programs in wilderness areas. To date, this monitoring document has yet to be evaluated under rigorous field conditions at a remote, high-elevation Rocky Mountain site. For the purpose of field testing approaches to monitoring of pollutants and ecosystems in remote, wilderness areas, evaluation criteria were developed. These include useability, cost-effectiveness, data variability, alternative approaches, ecosystems conceptual approach, and quality assurance. Both the Forest Service and INEL environmental monitoring techniques will be evaluated with these criteria. Another objective of this research plan is to obtain an integrated data base on pollutants and ecosystem structure and function at a remote study site. The methods tested in this project will be used to acquire these data from a systems approach. This includes multimedia monitoring of air and water quality, soils, and forest, stream, and lake ecosystems. 71 refs., 1 fig., 9 tabs

An integrated stewardship model : Antimicrobial, infection prevention and diagnostic (AID)

NARCIS (Netherlands)

Dik, Jan-Willem H.; Poelman, Randy; Friedrich, Alexander W.; Panday, Prashant Nannan; Lo-Ten-Foe, Jerome R.; van Assen, Sander; van Gemert-Pijnen, Julia E. W. C.; Niesters, Hubert G. M.; Hendrix, Ron; Sinha, Bhanu

2016-01-01

Considering the threat of antimicrobial resistance and the difficulties it entails in treating infections, it is necessary to cross borders and approach infection management in an integrated, multidisciplinary manner. We propose the antimicrobial, infection prevention and diagnostic stewardship

An integrated stewardship model: antimicrobial, infection prevention and diagnostic (AID)

NARCIS (Netherlands)

Dik, Jan-Willem H.; Poelman, Randy; Friedrich, Alexander W.; Panday, Prashant N.; Lo-Ten-Foe, Jerome R.; van Assen, Sander; van Gemert-Pijnen, Julia E.W.C.; Niesters, Hubert G.M.; Hendrix, Ron; Sinha, Bhanu

2015-01-01

Considering the threat of antimicrobial resistance and the difficulties it entails in treating infections, it is necessary to cross borders and approach infection management in an integrated, multidisciplinary manner. We propose the antimicrobial, infection prevention and diagnostic stewardship

Integrated assessment of air pollution by metals and source apportionment using ryegrass (Lolium multiflorum Lam.) in southern Brazil.

Science.gov (United States)

Illi, Júlia Carolina; Vancetta, Tafael; Alves, Darlan Daniel; Osório, Daniela Montanari Migliavacca; Bianchin, Liane; de Quevedo, Daniela Müller; Juchem, Fernando

2017-01-01

One of the biggest environmental problems existing today is air pollution, which is characterized by the presence of toxic gases and metal pollutants, the latter of which is generally associated with emissions of particulate matter (PM) from industries or automotive vehicles. Biomonitoring is a method that can be used to assess air pollution levels because it makes it possible to determine what effects these air pollutants cause in living organisms and their responses. The species Lolium multiflorum Lam., known as ryegrass, is considered a good bioindicator of metals, since it accumulates these substances during exposure. This study proposes to conduct an integrated assessment of air quality using two different monitoring methodologies: biomonitoring with L. multiflorum and active monitoring in areas with different levels of urbanization and industrialization. Concentrations found in ryegrass plants revealed high levels of Pb, Cr, Zn, and Cu, indicating that vehicular and industrial emissions were the main sources of pollution. Analysis of PM also revealed soot and biogenic particles, which can transport metals. Therefore, with the proposed method, the anthropogenic impact on air pollution in the investigated area could be clearly demonstrated.

Air pollutants and the leaf cuticle. Proceedings

International Nuclear Information System (INIS)

Percy, K.E.; Jagels, R.; Simpson, C.J.

1994-01-01

The leaf surface forms the interface between plants and a deteriorating atmospheric environment. It is, therefore, the first point of contact between plants and air pollutants and presents an effective barrier to pollutant entry. Outermost surfaces of leaves are covered by a thin, lipoidal, non-living membrane called a cuticle. Cuticle integrity is essential to plant survival and has many essential functions, including the prevention of excessive water loss, regulation of solute uptake and protection of sensitive underlying photosynthetic tissues against harmful irradiation such as enhanced UV-B resulting from stratospheric ozone depletion. The physicochemical properties of the cuticle vary greatly between and within species. They are known to be sensitive to change through natural and anthropogenic influences. This book comprises contributions made to a NATO-sponsored Advanced Research Workshop ''Air Pollutants and the Leaf Cuticle'' held October 4-9, 1993 in Fredericton, New Brunswick, Canada. The objective of the ARW was to bring together for the first time international expertise on the subject of air pollutant interactions with the cuticle. In order to facilitate a state-of-science review, the ARW was structured around four themes. They were as follows: 1. Cuticular physicochemical characteristics, physiological, regulatory, and protective roles. 2. Effects, mechanisms, and consequences of air pollutant interaction with leaf cuticles. 3. Non-anthropogenic and environmental influences on the cuticle and potential of the cuticle for biomonitoring and critical levels mapping. 4. New developments in experimental methodology and analytical techniques. (orig./vhe)

Environmental Restoration Program pollution prevention checklist guide for the surveillance and maintenance project phase

International Nuclear Information System (INIS)

1993-09-01

DOE Order 5820.2 mandates that a surveillance and maintenance program be established in all shut-down facilities to ensure adequate containment of contamination, provide physical safety and security, and reduce potential public and environmental hazards. A key consideration in this process is the prevention of any waste to be generated from these activities. The purpose of this checklist guide is to assist the user with incorporating pollution prevention/waste minimization (PP/WM) in all Surveillance and Maintenance (S ampersand M) phase projects of the Environmental Restoration (ER) Program. This guide will help users document their PP/WM activities for technology transfer and reporting requirements. Automated computer screens will be created from the checklist data to assist users with implementing and evaluating waste reduction. Users can then establish numerical performance measures to measure progress in planning, training, self-assessments, field implementation, documentation, and technology transfer. Cost savings result as users train and assess themselves and perform preliminary waste assessments

Integrated Assessment of Prevention and Restoration Actions to Combat Desertification

Science.gov (United States)

Bautista, S.; Orr, B. J.; Vallejo, R.

2009-12-01

Recent advances in desertification and land degradation research have provided valuable conceptual and analytical frameworks, degradation indicators, assessment tools and surveillance systems with respect to desertification drivers, processes, and impacts. These findings, together with stakeholders’ perceptions and local/regional knowledge, have helped to define and propose measures and strategies to combat land degradation. However, integrated and comprehensive assessment and evaluation of prevention and restoration strategies and techniques to combat desertification is still lacking, and knowledge on the feasibility and cost-effectiveness of the proposed strategies over a wide range of environmental and socio-economic conditions is very scarce. To address this challenge, we have launched a multinational project (PRACTICE - Prevention and Restoration Actions to Combat Desertification. An Integrated Assessment), funded by the European Commission, in order to link S & T advances and traditional knowledge on prevention and restoration practices to combat desertification with sound implementation, learning and adaptive management, knowledge sharing, and dissemination of best practices. The key activities for pursuing this goal are (1) to establish a platform and information system of long-term monitoring sites for assessing sustainable management and actions to combat desertification, (2) to define an integrated protocol for the assessment of these actions, and (3) to link project assessment and evaluation with training and education, adaptive management, and knowledge sharing and dissemination through a participatory approach involving scientists, managers, technicians, financial officers, and members of the public who are/were impacted by the desertification control projects. Monitoring sites are distributed in the Mediterranean Europe (Greece, Italy, Spain, and Portugal), Africa (Morocco, Namibia, South Africa), Middle East (Israel), China, and South and North

Groundwater pollution: Are we monitoring appropriate parameters ...

African Journals Online (AJOL)

Groundwater pollution is a worldwide phenomenon with potentially disastrous consequences. Prevention of pollution is the ideal approach. However, in practice groundwater quality monitoring is the main tool for timely detection of pollutants and protection of groundwater resources. Monitoring groundwater quality is a ...

HIA and pollution prevention control: What they can learn from each other

International Nuclear Information System (INIS)

Ahmad, Balsam; Pless-Mulloli, Tanja; Vizard, Catherine

2005-01-01

Following the implementation of the Pollution Prevention and Control (England and Wales) Regulations on 1st August 2000, health authorities (now Primary Care Trusts) became statutory consultees for permits issued to industry by the environmental regulators (the Environmental Agency, Local Authorities). The aims of this paper are to review the process of providing public health input in the light of its similarities to and differences from HIA and to identify the opportunities for both HIA and PPC to learn from each other's practice. We emphasise the challenges that are encountered by public health professionals who provide the public health input in the PPC. We use both our own experience of providing this input on behalf of health authorities and our expertise in HIA, environmental epidemiology and contaminated land

Special Operations can make a difference in integrated conflict prevention

DEFF Research Database (Denmark)

Jensen, Lars H. Ehrensvärd

The fifth brief in the series about special operations highlights the possible strategic role of special operations in connection with Denmark's revitalized vision of integration of the state's instruments to create security through preventive stabilization efforts. The brief offers suggestion...

Methodologies of health impact assessment as part of an integrated approach to reduce effects of air pollution

OpenAIRE

Aunan, Kristin; Seip, Hans Martin

1995-01-01

Quantification of average frequencies of health effects on a population level is an essential part of an integrated assessment of pollution effects. Epidemiological studies seem to provide the best basis for such estimates. This paper gives an introduction to a methodology for health impact assessment. It also gives results from some selected parts of a case-study in Hungary. This study is aimed at testing and improving the methodology for integrated assessment and focuses on energy productio...

Amoco-US Environmental Protection Agency, pollution prevention project, Yorktown, Virginia: Project peer review. Report of the Peer Review Committee of the Amoco/EPA Pollution Prevention Project at the Yorktown, Virginia refinery

International Nuclear Information System (INIS)

Klee, H.; Podar, M.

1991-01-01

The Amoco/EPA Pollution Prevention Project involved a number of representatives from federal and Virginia regulatory agencies, and Amoco's refining business. Participants believed that the Project could benefit from a broader perspective than these organizations along might provide. The Project Work Group selected an independent Peer Review Process which was conducted by Resource for the Future (RFF), a Washington DC think tank. A group of technical, policy and environmental experts from diverse backgrounds served as Peer Review members. The Peer Review Committee met on three occasions to discuss (1) the Project Work Plan (2) sampling data and interpretation and (3) project conclusions and recommendations. The focus of the meeting was on the general scope and content of the project

Annual report of waste generation and pollution prevention progress 1997

International Nuclear Information System (INIS)

1998-09-01

This sixth Annual Report presents and analyzes DOE Complex-wide waste generation and pollution prevention activities at 36 reporting sites from 1993 through 1997. In May 1996, the Secretary of Energy established a 50 percent Complex-Wide Waste Reduction Goal (relative to the 1993 baseline) for routine operations radioactive and hazardous waste generation, to be achieved by December 31, 1999. Excluding sanitary waste, routine operations waste generation increased three percent from 1996 to 1997, and decreased 61 percent overall from 1993 to 1997. DOE has achieved its Complex-Wide Waste Reduction Goals for routine operations based upon a comparison of 1997 waste generation to the 1993 baseline. However, it is important to note that increases in low-level radioactive and low-level mixed waste generation could reverse this achievement. From 1996 to 1997, low-level radioactive waste generation increased 10 percent, and low-level mixed waste generation increased slightly. It is critical that DOE sites continue to reduce routine operations waste generation for all waste types, to ensure that DOE's Complex-Wide Waste Reduction Goals are achieved by December 31, 1999

Integrated survey of water pollution in the Suquía River basin (Córdoba, Argentina).

Science.gov (United States)

Monferrán, Magdalena Victoria; Galanti, Lucas Nicolás; Bonansea, Rocío Inés; Amé, María Valeria; Wunderlin, Daniel Alberto

2011-02-01

We report a combined two-year seasonal monitoring of Suquía River basin using both chemical parameters and biomarkers measured in Jenynsia multidentata, aiming to correlate external levels of contaminants with the response of oxidative stress biomarkers in this fish. Identified pollution sources correspond to city sewage as well as agricultural and small industry activities downstream from Córdoba city. Physicochemical parameters integrated into a water quality index (WQI) were measured in Suquía River during dry and wet seasons. Ag, Mn, Cu, Cr, Ni, Fe, Pb and Zn were also monitored in water and sediment samples. Biomarkers include detoxication and antioxidant enzymes: catalase (CAT), glutathione peroxidase (GPX), glutathione S-transferase (GST) and glutathione reductase (GR). Enzymes showed a pollution dependent response, with increased activities in fish collected close to the sewage exit and progressive drop further downstream, matching changes in the Water Quality index. The combined use of biomarkers with water quality parameters allowed both the identification of pollution sources and the evaluation of effects of contaminants on the aquatic biota.

Integrated solutions for urban runoff pollution control in Brazilian metropolitan regions.

Science.gov (United States)

Morihama, A C D; Amaro, C; Tominaga, E N S; Yazaki, L F O L; Pereira, M C S; Porto, M F A; Mukai, P; Lucci, R M

2012-01-01

One of the most important causes for poor water quality in urban rivers in Brazil is the low collection efficiency of the sewer system due to unforeseen interconnections with the stormwater drainage system. Since the beginning of the 20th century, Brazilian cities have adopted separate systems for sanitary sewers and stormwater runoff. Gradually these two systems became interconnected. A major challenge faced today by water managers in Brazil is to find efficient and low cost solutions to deal with this mixed system. The current situation poses an important threat to the improvement of the water quality in urban rivers and lakes. This article presents an evaluation of the water quality parameters and the diffuse pollution loads during rain events in the Pinheiros River, a tributary of the Tietê River in São Paulo. It also presents different types of integrated solutions for reducing the pollution impact of combined systems, based on the European experience in urban water management. An evaluation of their performance and a comparison with the separate system used in most Brazilian cities is also presented. The study is based on an extensive water quality monitoring program that was developed for a special investigation in the Pinheiros River and lasted 2.5 years. Samples were collected on a daily basis and water quality variables were analyzed on a daily, weekly or monthly basis. Two hundred water quality variables were monitored at 53 sampling points. During rain events, additional monitoring was carried out using an automated sampler. Pinheiros River is one of the most important rivers in the São Paulo Metropolitan Region and it is also a heavily polluted one.

SANCOR marine pollution research programme 1986-1990

CSIR Research Space (South Africa)

SANCOR

1985-01-01

Full Text Available The Marine Pollution Research Programme is one of the series of SANCOR Programmes. Up to 1985 research into these aspects of oil pollution covered by the Prevention and combating of Pollution of the Sea by Oil Act (no. 6 of 1981) has been...

Preventive measures of water pollution in China; Chugoku ni okeru suishitsu odaku boshi taisaku

Energy Technology Data Exchange (ETDEWEB)

Qian, Y.; Huang, X.

1996-01-10

This paper describes the progress and the major results of research and development on technologies and measures to prevent water pollution in China. Tests and researches have been performed on an upward anaerobic sludge blanket (UASB), a vertical baffled anaerobic sludge blanket, two-phase anaerobic digestion, and an anaerobic fluidized bed. When anaerobically digested sludge and aerobic active sludge are inoculated in the UASB, particle-shaped sludge was formed well in both sludges. This technology has begun to be used in breweries and citric acid factories. With anaerobic treatment of waste water containing sulfate, the sulfate was recovered as sulfur by using the first and second phases. Research and development is being progressed on the oxidation ditch technology as an improved version of the active sludge method. In a pilot test of a soil treatment system and a stabilization pond treatment system as alternative technology for the active sludge method, the BOD in the treated water was found 2.5 mg{times}1/l. Attentions are drawn on primary treatment, a living organism contact oxidation method, and a continuous filtration treatment process as technologies to turn polluted water into resources. 6 refs., 1 tab.

Stress Prevention@Work : A study protocol for the evaluation of a multifaceted integral stress prevention strategy to prevent employee stress in a healthcare organization: a cluster controlled trial

NARCIS (Netherlands)

Hoek, R.J.A.; Havermans, B.M.; Houtman, I.L.D.; Brouwers, E.P.M.; Heerkens, Y.F.; Zijlstra-vlasveld, M.C.; Anema, J.R.; van der Beek, A.J.; Boot, C.R.L.

2018-01-01

Adequate implementation of work-related stress management interventions can reduce or prevent work-related stress and sick leave in organizations. We developed a multifaceted integral stress-prevention strategy for organizations from several sectors that includes a digital platform and collaborative

Stress Prevention@Work: a study protocol for the evaluation of a multifaceted integral stress prevention strategy to prevent employee stress in a healthcare organization: a cluster controlled trial

NARCIS (Netherlands)

Hoek, R.J.A.; Havermans, B.M.; Houtman, I.L.D.; Brouwers, E.P.M.; Heerkens, Y.F.; Zijlstra-Vlasveld, M.C.; Anema, J.R.; Beek, A.J. van der; Boot, C.R.L.

2017-01-01

Background. Adequate implementation of work-related stress management interventions can reduce or prevent work-related stress and sick leave in organizations. We developed a multifaceted integral stress-prevention strategy for organizations from several sectors that includes a digital platform and

Best management practices to reduce and prevent water pollution with herbicides from run-off and erosion

Directory of Open Access Journals (Sweden)

Gehring, Klaus

2014-02-01

Full Text Available The natural phenomenon of run-off and erosion lead to unpreventable pesticide water pollution in case of extreme weather conditions. In this relationship the use of herbicides involves a higher risk than other pesticides because of the specific terms of application. Directive 2009/128/EC for the sustainable use of pesticides aspires to enhanced water protection. German national action plan contains quantitative objectives which require strong reduction of water pollution by run-off and erosion of pesticides and accordingly herbicides. The European TOPPS prowadis project developed a consolidated and basic diagnosis concept for the first time to determine the field specific run-off risk. Compatible mitigation measures were linked to specific risk scenarios. Risk diagnosis and suitable mitigation measures determine best management practices for the prevention of run-off and erosion. Different new diagnosis methods and the implementation are presented. Further documents and information are available on the web [http://www.topps-life.org/].

Oil pollution control mechanisms - statutes and regulations

International Nuclear Information System (INIS)

1978-04-01

The purpose of this analysis is to provide a detailed picture of federal statutes and regulations, as well as case law, bearing on oil spill prevention and control. Emphasis has been placed on federal action occurring after a spill, although some effort is directed toward review of prevention statutes and regulations. In-depth consideration is given the control of oil pollution under the Federal Water Pollution Control Act but this analysis also touches lightly upon acts that have a lesser effect on oil pollution control. These acts being: The Refuse Act; The Ports and Waterways Safety Act of 1972; The Outer Continental Shelf Lands Act; The Oil Pollution Act of 1961; The Deepwater Port Act of 1974, and The Fish and Wildlife Coordination Act

Quantifying light pollution

International Nuclear Information System (INIS)

Cinzano, P.; Falchi, F.

2014-01-01

In this paper we review new available indicators useful to quantify and monitor light pollution, defined as the alteration of the natural quantity of light in the night environment due to introduction of manmade light. With the introduction of recent radiative transfer methods for the computation of light pollution propagation, several new indicators become available. These indicators represent a primary step in light pollution quantification, beyond the bare evaluation of the night sky brightness, which is an observational effect integrated along the line of sight and thus lacking the three-dimensional information. - Highlights: • We review new available indicators useful to quantify and monitor light pollution. • These indicators are a primary step in light pollution quantification. • These indicators allow to improve light pollution mapping from a 2D to a 3D grid. • These indicators allow carrying out a tomography of light pollution. • We show an application of this technique to an Italian region

Waste minimization and pollution prevention in D ampersand D operations at the Argonne National Laboratory-East site

International Nuclear Information System (INIS)

Boing, L.E.; Coffey, M.J.; Ditch, R.W.; Fellhauer, C.R.; Rose, R.W.

1996-01-01

Argonne National Laboratory (ANL) is implementing waste minimization and pollution prevention activities into its conduct of decontamination and decommissioning (D ampersand D) projects. Many of these activities are rather straight forward and simple approaches, yet they are often overlooked and not implemented as often as they should or could be. Specific activities involving recycling and reuse of materials and structures, which have proven useful in lowering decommissioning and disposal costs on D ampersand D projects at ANL are presented

Radioactive contamination, what actions for the polluted sites

International Nuclear Information System (INIS)

2004-01-01

The nuclear safety authority and the direction of prevention of pollutions and risks have organised the first edition of the national colloquium: radioactive contamination: what actions for polluted sites. Four axes can be taken to follow this colloquium: prevention, outstanding tools to evaluate risks and rehabilitation, a better responsibility of operators and memory keeping. (N.C.)

[Role and integration of technical prevention figures in the management system].

Science.gov (United States)

Bartolucci, G B; Santantonio, P; Casciani, M; Dagazzini, I

2010-01-01

The multifarious issues of health and safety at work require multi-disciplinary skills, both in the risk assessment and in the subsequent definition and management of preventive measures, and this requires a renewed operational protocol that supports integration and co-operation between the technical prevention figures. Thus, between occupational physicians and technical advisers there should be a concrete and fruitful interaction, which should not be episodic or occasional, but a modus operandi systematic and constant. In this contribution is discussed as the technical prevention figures should be included in the Health and Safety Management System and should make a specific contribution in defining corporate policies on prevention. In particular it is outlined the role that the occupational physician may play in the development of prevention and health promotion activities within the strategies of corporate social responsibility.

ENVIRONMENTAL POLLUTION

OpenAIRE

Reyna Ramos, julio

2014-01-01

The article shows the complexity of the problem of environmental pollution and what can be the possible solutions to the problem. Also, how the Industrial Engineering can contribute to the prevention and control of pollution. El artículo muestra la complejidad del problema de la contaminación ambiental y cuáles pueden ser las propuestas de solución al problema. Así mismo, cómo la Ingeniería Industrial puede contribuir a la prevención y control de la contaminación.

Evaluating the effect of human activity patterns on air pollution exposure using an integrated field-based and agent-based modelling framework

Science.gov (United States)

Schmitz, Oliver; Beelen, Rob M. J.; de Bakker, Merijn P.; Karssenberg, Derek

2015-04-01

Constructing spatio-temporal numerical models to support risk assessment, such as assessing the exposure of humans to air pollution, often requires the integration of field-based and agent-based modelling approaches. Continuous environmental variables such as air pollution are best represented using the field-based approach which considers phenomena as continuous fields having attribute values at all locations. When calculating human exposure to such pollutants it is, however, preferable to consider the population as a set of individuals each with a particular activity pattern. This would allow to account for the spatio-temporal variation in a pollutant along the space-time paths travelled by individuals, determined, for example, by home and work locations, road network, and travel times. Modelling this activity pattern requires an agent-based or individual based modelling approach. In general, field- and agent-based models are constructed with the help of separate software tools, while both approaches should play together in an interacting way and preferably should be combined into one modelling framework, which would allow for efficient and effective implementation of models by domain specialists. To overcome this lack in integrated modelling frameworks, we aim at the development of concepts and software for an integrated field-based and agent-based modelling framework. Concepts merging field- and agent-based modelling were implemented by extending PCRaster (http://www.pcraster.eu), a field-based modelling library implemented in C++, with components for 1) representation of discrete, mobile, agents, 2) spatial networks and algorithms by integrating the NetworkX library (http://networkx.github.io), allowing therefore to calculate e.g. shortest routes or total transport costs between locations, and 3) functions for field-network interactions, allowing to assign field-based attribute values to networks (i.e. as edge weights), such as aggregated or averaged

Optimizing production and imperfect preventive maintenance planning's integration in failure-prone manufacturing systems

International Nuclear Information System (INIS)

Aghezzaf, El-Houssaine; Khatab, Abdelhakim; Tam, Phuoc Le

2016-01-01

This paper investigates the issue of integrating production and maintenance planning in a failure-prone manufacturing system. It is assumed that the system's operating state is stochastically predictable, in terms of its operating age, and that it can accordingly be preventively maintained during preplanned periods. Preventive maintenance is assumed to be imperfect, that is when performed, it brings the manufacturing system to an operating state that lies between ‘as bad as old’ and ‘as good as new’. Only an overhauling of the system brings it to a ‘as good as new’ operating state again. A practical integrated production and preventive maintenance planning model, that takes into account the system's manufacturing capacity and its operational reliability state, is developed. The model is naturally formulated as a mixed-integer non-linear optimization problem, for which an extended mixed-integer linear reformulation is proposed. This reformulation, while it solves the proposed integrated planning problem to optimality, remains quite demanding in terms of computational time. A fix-and-optimize procedure, that takes advantage of some properties of the original model, is then proposed. The reformulation and the fix-and-optimize procedure are tested on some test instances adapted from those available in the literature. The results show that the proposed fix-and-optimize procedure performs quite well and opens new research direction for future improvements. - Highlights: • Integration of production planning and imperfect preventive maintenance is explored. • Imperfect maintenance is modeled using a fitting age reduction hybrid hazard rate. • A practical approximate optimization model for this integration is proposed. • The resulting naturally MINL optimization model is reformulated and solved as a MILP. • An effective fix-and-optimize procedure is proposed for large instances of this MILP.

Environmental pollution and kidney diseases.

Science.gov (United States)

Xu, Xin; Nie, Sheng; Ding, Hanying; Hou, Fan Fan

2018-05-01

The burden of disease and death attributable to environmental pollution is becoming a public health challenge worldwide, especially in developing countries. The kidney is vulnerable to environmental pollutants because most environmental toxins are concentrated by the kidney during filtration. Given the high mortality and morbidity of kidney disease, environmental risk factors and their effect on kidney disease need to be identified. In this Review, we highlight epidemiological evidence for the association between kidney disease and environmental pollutants, including air pollution, heavy metal pollution and other environmental risk factors. We discuss the potential biological mechanisms that link exposure to environmental pollutants to kidney damage and emphasize the contribution of environmental pollution to kidney disease. Regulatory efforts should be made to control environmental pollution and limit individual exposure to preventable or avoidable environmental risk. Population studies with accurate quantification of environmental exposure in polluted regions, particularly in developing countries, might aid our understanding of the dose-response relationship between pollutants and kidney diseases.

Air pollution control policy in Switzerland

Energy Technology Data Exchange (ETDEWEB)

Leutert, G. [Forests and Landscape, Berne (Switzerland). Federal Office of Environment

1995-12-31

The legal basis of the Swiss air pollution control policy is set by the Federal Law on the Protection of the Environment, which came into force in 1985. It aims to protect human beings, animals and plants, their biological communities and habitats against harmful effects or nuisances and to maintain the fertility of the soil. The law is source-oriented (by emission standards) as well as effect-oriented (by ambient air quality standards). To link both elements a two-stage approach is applied. In the first stage preventive measures are taken at the emitting sources, irrespective of existing air pollution levels. Emissions have to be limited by early preventive measures as much as technical and operational conditions allow and as far as economically acceptable (prevention principle). By this, air pollution shall be kept as low as possible as a matter of principle, without the environment having to be in danger first. In a second stage the measures are strengthened or backed up by additional measures if ambient air quality standards laid down in the Ordinance on Air Pollution Control are exceeded. At this second stage, protection of man and his environment has priority over economic considerations. (author)

Air pollution control policy in Switzerland

Energy Technology Data Exchange (ETDEWEB)

Leutert, G [Forests and Landscape, Berne (Switzerland). Federal Office of Environment

1996-12-31

The legal basis of the Swiss air pollution control policy is set by the Federal Law on the Protection of the Environment, which came into force in 1985. It aims to protect human beings, animals and plants, their biological communities and habitats against harmful effects or nuisances and to maintain the fertility of the soil. The law is source-oriented (by emission standards) as well as effect-oriented (by ambient air quality standards). To link both elements a two-stage approach is applied. In the first stage preventive measures are taken at the emitting sources, irrespective of existing air pollution levels. Emissions have to be limited by early preventive measures as much as technical and operational conditions allow and as far as economically acceptable (prevention principle). By this, air pollution shall be kept as low as possible as a matter of principle, without the environment having to be in danger first. In a second stage the measures are strengthened or backed up by additional measures if ambient air quality standards laid down in the Ordinance on Air Pollution Control are exceeded. At this second stage, protection of man and his environment has priority over economic considerations. (author)

Management of polluted deposit in lake and river

Energy Technology Data Exchange (ETDEWEB)

Lee, Chang Hee; Kim, Eun Jung [Korea Environment Institute, Seoul (Korea)

1998-12-01

In this study, the perception and problem of polluted deposit in Korea, which does not have a clear concept of it, were analyzed and the need of a comprehensive polluted deposit management, including the present condition of pollution, assessment, pollution prevention, and disposal of polluted deposit, was presented. Based on the analysis on foreign management system, the framework of polluted deposit management in Korea was provided. 84 refs., 11 figs., 40 tabs.

Prevention of air pollution: guidebook of the French techniques of dedusting and purification of gases and smokes in the industry; Prevention de la pollution de l'air: guide des techniques francaises de depoussierage et d'epuration des gaz et fumees dans l'industrie

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

This new edition favours the multi-pollutants approach and integrates the improvements made in the European standardization of emission measurements. It contributes to the diffusion of the French techniques in the domain of gases dedusting and purification. (J.S.)

Amoco-US Environmental Protection Agency, pollution prevention project, Yorktown, Virginia: Yorktown refinery project workplan

International Nuclear Information System (INIS)

Curran, L.; Grieves, C.; Browning, R.; Hanlon, D.; Crane, C.

1990-09-01

The report provides a detailed workplan for obtaining data and analyzing results for a 2-year pollution prevention study of Amoco Oil Company's Yorktown Virginia Refinery. The study was jointly sponsored as a cooperative effort of Amoco Corporation and the United States Environmental Protection Agency. The goals of the study include (1) a multi-media inventory of all releases entering the environment from the Refinery, (2) development of possible engineering options to reduce the releases, (3) analysis of each option in terms of release reduction potential, impact on human health risk, ecological impact, changes in future liability, etc. and (4) identification of obstacles and incentives for implementation of any of the options considered

Integrating environmental taxes on local air pollutants with fiscal reform in Hungary: simulations with a computable general equilibrium model

International Nuclear Information System (INIS)

Morris, Glenn E.; Revesz, Tamas; Zalai, Ernoe; Fucsko, Jozsef

1999-01-01

This paper describes the Fiscal Environmental Integration Model (FEIM) and its use to examine the merits of introducing a set of air pollutant emission taxes and stringent abatement requirements based on best commonly available control technology. These environmental protection strategies are examined both independently and in combination. In addition, Hungary has very high VAT, employment, and income tax rates and therefore might receive more than the usual advantage from using environmental tax revenues to reduce other taxes. We therefore also examine the economic and environmental implications of different uses of the revenues generated by the air pollutant emissions taxes. FEIM is a CGE model of the Hungarian economy that includes sectoral air pollution control costs functions and execution options that allow examination of the key policy choices involved. We developed and ran a baseline and seven scenarios with FEIM. The scenarios centered on introduction of environmental load fees (ELF) on emissions of SO 2 , NO x , and particulates and emission abatement requirements (EAR) for these pollutants. (Author)

Pricing Mechanism Design for Centralized Pollutant Treatment with SME Alliances

Directory of Open Access Journals (Sweden)

Yuyu Li

2016-06-01

Full Text Available In this paper, we assume that a professional pollutant treatment enterprise treats all of the pollutants emitted by multiple small and medium-sized enterprises (SMEs. In order to determine the treatment price, SMEs can bargain with the pollutant treatment enterprise individually, or through forming alliances. We propose a bargaining game model of centralized pollutant treatment to study how the pollutant treatment price is determined through negotiation. Then, we consider that there is a moral hazard from SMEs in centralized pollutant treatment; in other words, they may break their agreement concerning their quantities of production and pollutant emissions with the pollutant treatment enterprise. We study how the pollutant treatment enterprise can prevent this by pricing mechanism design. It is found that the pollutant treatment enterprise can prevent SMEs’ moral hazard through tiered pricing. If the marginal treatment cost of the pollutant treatment enterprise is a constant, SMEs could bargain with the pollutant treatment enterprise individually, otherwise, they should form a grand alliance to bargain with it as a whole.

Pricing Mechanism Design for Centralized Pollutant Treatment with SME Alliances.

Science.gov (United States)

Li, Yuyu; Huang, Bo; Tao, Fengming

2016-06-22

In this paper, we assume that a professional pollutant treatment enterprise treats all of the pollutants emitted by multiple small and medium-sized enterprises (SMEs). In order to determine the treatment price, SMEs can bargain with the pollutant treatment enterprise individually, or through forming alliances. We propose a bargaining game model of centralized pollutant treatment to study how the pollutant treatment price is determined through negotiation. Then, we consider that there is a moral hazard from SMEs in centralized pollutant treatment; in other words, they may break their agreement concerning their quantities of production and pollutant emissions with the pollutant treatment enterprise. We study how the pollutant treatment enterprise can prevent this by pricing mechanism design. It is found that the pollutant treatment enterprise can prevent SMEs' moral hazard through tiered pricing. If the marginal treatment cost of the pollutant treatment enterprise is a constant, SMEs could bargain with the pollutant treatment enterprise individually, otherwise, they should form a grand alliance to bargain with it as a whole.

A Study of Heavy Metal Pollution in China: Current Status, Pollution-Control Policies and Countermeasures

Directory of Open Access Journals (Sweden)

Hui Hu

2014-09-01

Full Text Available In the past 30 years, China’s economy has experienced rapid development, which led to a vast increase in energy consumption and serious environmental pollution. Among the different types of pollution, heavy metal pollution has become one of the major environmental issues in China. A number of studies show that high level of heavy metal exposure is a frequent cause of permanent intellectual and developmental disabilities. In recent years, some traditional pollutants, such as sulfur dioxide and carbon dioxide, have been put under control in China. However, heavy metal pollution, which poses even greater risks to public health and sustainable development, has yet to gain policymakers’ attention. The purpose of this paper is to explore effective countermeasures for heavy metal pollution in China. The present study reviews the current status of China’s heavy metal pollution and analyzes related public policies and countermeasures against that pollution. It also presents a few recommendations and measures for prevention of heavy metal pollution.

An integrated assessment of regional air pollution and climate change in Europe: findings of the AIR-CLIM project

NARCIS (Netherlands)

Alcamo, J.; Mayerhofer, P.; Guardans, R.; Harmelen, T. van; Minnen, J. van; Onigkeit, J.; Posch, M.; Vries, B. de

2002-01-01

This paper presents results of an assessment of the linkages between regional air pollution and climate change in Europe (the AIR-CLIM Project). The main research tool was an integrated modeling framework and the main product was a consistent set of long-term scenarios covering Europe between 1995

An integrated environmental decision support system for water pollution control based on TMDL--A case study in the Beiyun River watershed.

Science.gov (United States)

Zhang, Shanghong; Li, Yueqiang; Zhang, Tianxiang; Peng, Yang

2015-06-01

This paper details the development and application of an integrated environmental decision support system (EDSS) for water pollution control based on total maximum daily load (TMDL). The system includes an infrastructure, simulation, and application platforms. Using the water pollution control of Beiyun River in China as a case study, the key development processes and technologies of the EDSS are discussed including relations and links between various environmental simulation models, and model integration, visualization and real-time simulation methods. A loose coupling method is used to connect the environmental models, and an XML file is used to complete data exchange between different models. Project configuration and scheme configuration are used for simulation data organization. The integration approach is easy to implement and enables different development languages and reuse of existing models. The EDSS has been applied to water environment management of Beiyun River, and can be applied to other geographic regions. Copyright © 2015 Elsevier Ltd. All rights reserved.

Using local biodiversity to prevent pollution transfers to environmental components of a Mediterranean semi-arid ecosystem

Science.gov (United States)

Heckenroth, Alma; Rabier, Jacques; Laffont-Schwob, Isabelle

2014-05-01

In arid and semi-arid Mediterranean coastal areas, metals and metalloids (MM) pollution coming from unreclaimed brownfields has increased the negative environmental stresses leading to ecosystems degradations as soil erosion and losses of organic matter and biodiversity. On these sites, maintaining or restoring a local vegetation cover is considered as a key step to stop the degradation cycle. Furthermore, in a context of high pollution occurring in natural areas, phytoremediation is considered as an attractive alternative to conventional soil remediation techniques, the first reducing pollution transfers, improving the soil quality. In protected or natural areas, it is also important to perceive then design phytoremediation as a way to assist ecosystems recovery, using the restoration ecology concepts. However, only few works in the literature deal with the potential use of native Mediterranean plant species for phytoremediation. On the South-East coast of Marseille (France), the activity of the former smelting factory of l'Escalette, ceased since 1925. However, its brownfield is still a source of pollution by trace metals and metalloids for abiotic and biotic components of the surrounding massif. This massif hosts a rich biodiversity with rare and protected plant species despite the metallic pollution and this area has been included in the recently created first peri-urban French National Park of Calanques. In this context, an integrated research project is being conducted with local actors and stakeholders, from the selection of native plant species, assessment and optimization of phytostabilization capacities of selected species, to the development of ecological engineering techniques well adapted to local constraints and phytostabilization field trials. The first part of this study has been conducted on two areas, corresponding to different pollution pattern, plant communities and environmental drivers: a halophytic area, characterized by typical coastal

Science Shop and NGO activities related to air pollution

DEFF Research Database (Denmark)

Jørgensen, Michael Søgaard; Brodersen, Søsser

2005-01-01

The paper describes activities, which these organisations and science shops carry out within the field of air pollution and its analysis, abatement and prevention. The activities have been mapped and analysed through dialogue with a number of these organisations. The activities include activities...... with focus on development of citizens' capacity for measurement and assessment of air pollution and strategies for abatement and prevention of air pollution. The paper discusses also possibilities for further development of dialogue and co-operation between civil society, science shops and ACCENT researchers....

Assessment of Pressure Sources and Water Body Resilience: An Integrated Approach for Action Planning in a Polluted River Basin.

Science.gov (United States)

Mirauda, Domenica; Ostoich, Marco

2018-02-23

The present study develops an integrated methodology combining the results of the water-quality classification, according to the Water Framework Directive 2000/60/EC-WFD, with those of a mathematical integrity model. It is able to analyse the potential anthropogenic impacts on the receiving water body and to help municipal decision-makers when selecting short/medium/long-term strategic mitigation actions to be performed in a territory. Among the most important causes of water-quality degradation in a river, the focus is placed on pollutants from urban wastewater. In particular, the proposed approach evaluates the efficiency and the accurate localisation of treatment plants in a basin, as well as the capacity of its river to bear the residual pollution loads after the treatment phase. The methodology is applied to a sample catchment area, located in northern Italy, where water quality is strongly affected by high population density and by the presence of agricultural and industrial activities. Nearly 10 years of water-quality data collected through official monitoring are considered for the implementation of the system. The sample basin shows different real and potential pollution conditions, according to the resilience of the river and surroundings, together with the point and diffuse pressure sources acting on the receiving body.

Assessment of Pressure Sources and Water Body Resilience: An Integrated Approach for Action Planning in a Polluted River Basin

Directory of Open Access Journals (Sweden)

Domenica Mirauda

2018-02-01

Full Text Available The present study develops an integrated methodology combining the results of the water-quality classification, according to the Water Framework Directive 2000/60/EC—WFD, with those of a mathematical integrity model. It is able to analyse the potential anthropogenic impacts on the receiving water body and to help municipal decision-makers when selecting short/medium/long-term strategic mitigation actions to be performed in a territory. Among the most important causes of water-quality degradation in a river, the focus is placed on pollutants from urban wastewater. In particular, the proposed approach evaluates the efficiency and the accurate localisation of treatment plants in a basin, as well as the capacity of its river to bear the residual pollution loads after the treatment phase. The methodology is applied to a sample catchment area, located in northern Italy, where water quality is strongly affected by high population density and by the presence of agricultural and industrial activities. Nearly 10 years of water-quality data collected through official monitoring are considered for the implementation of the system. The sample basin shows different real and potential pollution conditions, according to the resilience of the river and surroundings, together with the point and diffuse pressure sources acting on the receiving body.

Impact of Sustainable Environmental Expenditures Policy on Air Pollution Reduction, During European Integration Framework

Directory of Open Access Journals (Sweden)

Ionel Bostan

2016-05-01

Full Text Available Pursuant to the growth of society, against the boosting of scientific and technological progress, also arises the negative effect of pollution acceleration. In this context, we relate to risks that imply the growth of pollution, especially against nuisance air pollution increase (CO, SO2, NO etc. with major implications on the growth of greenhouse effect, the melting of the ice fields, respectively the pollution of the soil with nitrates from fertilizers intensively used in agriculture. Our study is up-to-date, as pursuant to the ONU Conference from Paris (France 2015, Conference on Climate Changes, they reached an agreement and the adopted text admits the menace of climate modifications is far more important than previously acknowledged and engages the participants to reduce their pollutant emissions. The researchers’ current concerns focus on studying the effects of the redistribution of financial resources obtained by practising the ‘green’ fiscal policy on dependent variables. Observing them, we integrate the respective variables into complex models analysed by multiple regression (both standard and robust and the fixed effects panel on 20 European countries which also reflect the different effects on the environmental policy and the expenses it incurred. The main purpose of the analysis we aim to accomplish is the impact of the policy for environment expenditure tenable within the European framework on against nuisance air pollution attenuation. The statistical analysis aims at identifying these effects by means of regression equations (OLS, robust regression (M method, fixed and random effects, using panel data from 18 EU countries, as well as Switzerland and Turkey due to their position in relation to the community block; we will analyse the period between 1995-2013. Further to the application of multiple regression statistical methods (OLS and robust M, our results show that teimiqgdp expenses played a major role in the reduction

Stormwater Pollution Prevention Plan - TA-60 Roads and Grounds Facility and Associated Sigma Mesa Staging Area

Energy Technology Data Exchange (ETDEWEB)

Sandoval, Leonard Frank [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2018-01-31

This Storm Water Pollution Prevention Plan (SWPPP) was developed in accordance with the provisions of the Clean Water Act (33 U.S.C. §§1251 et seq., as amended), and the Multi-Sector General Permit for Storm Water Discharges Associated with Industrial Activity (U.S. EPA, June 2015) issued by the U.S. Environmental Protection Agency (EPA) for the National Pollutant Discharge Elimination System (NPDES) and using the industry specific permit requirements for Sector P-Land Transportation and Warehousing as a guide. This SWPPP applies to discharges of stormwater from the operational areas of the TA-60 Roads and Grounds and Associated Sigma Mesa Staging Area at Los Alamos National Laboratory. Los Alamos National Laboratory (also referred to as LANL or the “Laboratory”) is owned by the Department of Energy (DOE), and is operated by Los Alamos National Security, LLC (LANS). Throughout this document, the term “facility” refers to the TA-60 Roads and Grounds and Associated Sigma Mesa Staging Area. The current permit expires at midnight on June 4, 2020.

Exposure to traffic-generated air pollutants mediates alterations in brain microvascular integrity in wildtype mice on a high-fat diet.

Science.gov (United States)

Suwannasual, Usa; Lucero, JoAnn; McDonald, Jacob D; Lund, Amie K

2018-01-01

Air pollution-exposure is associated with detrimental outcomes in the central nervous system (CNS) such as cerebrovascular disorders, including stroke, and neurodegenerative diseases. While the mechanisms of these CNS-related outcomes involved have not been fully elucidated, exposure to traffic-generated air pollutants has been associated with altered blood brain barrier (BBB) integrity and permeability. The current study investigated whether inhalation exposure to mixed vehicle emissions (MVE) alters cerebral microvascular integrity in healthy 3 mo old C57BL/6 mice, as well as whether exposure-mediated effects were exacerbated by a high-fat (HF) vs. low-fat (LF) diet. Mice on each diet were randomly assigned to be exposed to either filtered air (FA) or MVE [100PM/m 3 vehicle emissions mixture: 30µg PM/m 3 gasoline engine + 70µg PM/m 3 diesel engine emissions; median size ~ 60nm; particle mass size distribution median of ~ 1µm (range: diet, results in altered BBB integrity and increased ox-LDL signaling in the cerebral vasculature in a wildtype animal model. Copyright © 2017 Elsevier Inc. All rights reserved.

Environmental Restoration Program pollution prevention checklist guide for the facility characterization project phase

International Nuclear Information System (INIS)

1993-09-01

A facility characterization (FC) is conducted to determine the nature and extent contamination at a potential hazardous facility waste site. The information gathered during an FC includes (1) data on the volume and chemical nature of the waste, (2) information on the extent of contamination and the migration potential of the contaminants, (3) preliminary information on evaluation of alternative concepts that can or cannot be considered, and (4)supportive technical and cost data. For the purposes of identification, the following operational phases will be used for definition for this phase of the decommissioning and decontamination process (1) facility characterization before clean up, (2) characterization during clean up, (3) characterization of waste materials, and (4) site characterization after clean up. A key consideration in this process is the prevention of any waste to be generated from these characterization activities. The purpose of this checklist guide is to assist users with incorporating pollution prevention/waste minimization (PP/WM) in all FC phase projects of the Environmental Restoration (ER) Program. This guide will help users document PP/WM activities for technology transfer and reporting requirements. Automated computer screens will be created from the checklist data to assist users with implementing and evaluating waste reduction

Integrated analytical approaches for food traceability and pollution control

International Nuclear Information System (INIS)

2012-11-01

It developed in the laboratory of Food Science of the Montevideo commissariat a regional workshop with the following aims:To evaluate the effect of vegetable matrices on the determination of pesticides through analysis by GC / M S. For the implementation and application of these tests, it was applied the Laboratory s protocol which it was distributed to all members of the working group. It worked with a matrix lettuce, chard and a mix of green leafy vegetables , evaluating the matrix effect in the following pesticides: chloropyrifos, procimidione, L-cyhalothrin, azoxystrobin, trifluralin and fenbuconazole, using heptachlor as internal standard.They carried out in five concentration levels, in triplicate tests, applying the techniques of extraction by QuEChERS (kit agile nt). Prepared samples are injected into the GC / M S equipment, an analysis of the results were evaluated by the working group. Furthermore this regional workshop was about nuclear techniques role in agricultural practice, the traceability and pollution control, laboratory services and farmers relationships, environmental, economic, social and political impact, pest prevention and animal diseases, risk, the human health, environment protection in the agricultural and the pesticides uses.

Integrating Hazardous Materials Characterization and Assessment Tools to Guide Pollution Prevention in Electronic Products and Manufacturing

Science.gov (United States)

Lam, Carl

Due to technology proliferation, the environmental burden attributed to the production, use, and disposal of hazardous materials in electronics have become a worldwide concern. The major theme of this dissertation is to develop and apply hazardous materials assessment tools to systematically guide pollution prevention opportunities in the context of electronic product design, manufacturing and end-of-life waste management. To this extent, a comprehensive review is first provided on describing hazard traits and current assessment methods to evaluate hazardous materials. As a case study at the manufacturing level, life cycle impact assessment (LCIA)-based and risk-based screening methods are used to quantify chemical and geographic environmental impacts in the U.S. printed wiring board (PWB) industry. Results from this industrial assessment clarify priority waste streams and States to most effectively mitigate impact. With further knowledge of PWB manufacturing processes, select alternative chemical processes (e.g., spent copper etchant recovery) and material options (e.g., lead-free etch resist) are discussed. In addition, an investigation on technology transition effects for computers and televisions in the U.S. market is performed by linking dynamic materials flow and environmental assessment models. The analysis forecasts quantities of waste units generated and maps shifts in environmental impact potentials associated with metal composition changes due to product substitutions. This insight is important to understand the timing and waste quantities expected and the emerging toxic elements needed to be addressed as a consequence of technology transition. At the product level, electronic utility meter devices are evaluated to eliminate hazardous materials within product components. Development and application of a component Toxic Potential Indicator (TPI) assessment methodology highlights priority components requiring material alternatives. Alternative

Using a novel "Integrated Biomarker Proteomic" index to assess the effects of freshwater pollutants in European eel peripheral blood mononuclear cells.

Science.gov (United States)

Roland, Kathleen; Kestemont, Patrick; Dieu, Marc; Raes, Martine; Silvestre, Frédéric

2016-03-30

Using proteomic data as biomarkers of environmental pollution has the potential to be of a great interest in ecological risk assessment as they constitute early warning indicators of ecologically relevant effects on biological systems. To develop such specific and sensitive biomarkers, the use of a set of proteins is required and the identification of protein expression signatures (PES) may reflect the exposure to specific classes of pollutants. Using 2D-DIGE (Differential in Gel Electrophoresis) methodology, this study aimed at identifying specific PES on European eel (Anguilla anguilla) peripheral blood mononuclear cells (PBMC) after 48 h in vitro exposure to two sublethal concentrations of dichlorodiphenyltrichloroethane (p,p'-DDT) (10 μg/L and 1mg/L) or cadmium (Cd) (1 μg/L and 100 μg/L). The present results have been supplemented with data of a first in vitro study on cells exposed to perfluorooctane sulfonate (PFOS) (10 μg/L and 1mg/L). A total of thirty-four protein spots, belonging to 18 different identified proteins found in all conditions, have been selected as possible biomarkers to develop a synthetic Integrated Biomarker Proteomic (IBP) index. IBP follows a dose-response relationship with higher values at the highest tested concentration for each pollutant (Cd: 9.96; DDT: 7.44; PFOS: 7.94) compared to the lowest tested concentration (Cd: 3.81; DDT: 2.91; PFOS: 2.06). In a second step, star plot graphs have been applied to proteomic data in order to allow visual integration of a set of early warning responses measured with protein biomarkers. Such star plots permit to discriminate the type of pollutant inducing a proteomic response. We conclude that using IBP is relevant in environmental risk assessment, giving to this index the potential to be applied as a global index of proteome alteration in endangered species such as the European eel. In this study, 34 protein spots have been selected as possible biomarkers to develop a synthetic Integrated

Integrating Early Child Development and Violence Prevention Programs: A Systematic Review

Science.gov (United States)

Efevbera, Yvette; McCoy, Dana C.; Wuermli, Alice J.; Betancourt, Theresa S.

2018-01-01

Limited evidence describes promoting development and reducing violence in low- and middle-income countries (LMICs), a missed opportunity to protect children and promote development and human capital. This study presents a systematic literature review of integrated early childhood development plus violence prevention (ECD+VP) interventions in…

The Impact of Pollution Prevention on Toxic Environmental Releases from U.S. Manufacturing Facilities.

Science.gov (United States)

Ranson, Matthew; Cox, Brendan; Keenan, Cheryl; Teitelbaum, Daniel

2015-11-03

Between 1991 and 2012, the facilities that reported to the U.S. Environmental Protection Agency's Toxic Release Inventory (TRI) Program conducted 370,000 source reduction projects. We use this data set to conduct the first quasi-experimental retrospective evaluation of how implementing a source reduction (pollution prevention) project affects the quantity of toxic chemicals released to the environment by an average industrial facility. We use a differences-in-differences methodology, which measures how implementing a source reduction project affects a facility's releases of targeted chemicals, relative to releases of (a) other untargeted chemicals from the same facility, or (b) the same chemical from other facilities in the same industry. We find that the average source reduction project causes a 9-16% decrease in releases of targeted chemicals in the year of implementation. Source reduction techniques vary in effectiveness: for example, raw material modification causes a large decrease in releases, while inventory control has no detectable effect. Our analysis suggests that in aggregate, the source reduction projects carried out in the U.S. since 1991 have prevented between 5 and 14 billion pounds of toxic releases.

An integrated approach to model the biomagnification of organic pollutants in aquatic food webs of the Yangtze Three Gorges Reservoir ecosystem using adapted pollution scenarios.

Science.gov (United States)

Scholz-Starke, Björn; Ottermanns, Richard; Rings, Ursula; Floehr, Tilman; Hollert, Henner; Hou, Junli; Li, Bo; Wu, Ling Ling; Yuan, Xingzhong; Strauch, Katrin; Wei, Hu; Norra, Stefan; Holbach, Andreas; Westrich, Bernhard; Schäffer, Andreas; Roß-Nickoll, Martina

2013-10-01

The impounding of the Three Gorges Reservoir (TGR) at the Yangtze River caused large flooding of urban, industrial, and agricultural areas, and profound land use changes took place. Consequently, substantial amounts of organic and inorganic pollutants were released into the reservoir. Additionally, contaminants and nutrients are entering the reservoir by drift, drainage, and runoff from adjacent agricultural areas as well as from sewage of industry, aquacultures, and households. The main aim of the presented research project is a deeper understanding of the processes that determines the bioaccumulation and biomagnification of organic pollutants, i.e., mainly pesticides, in aquatic food webs under the newly developing conditions of the TGR. The project is part of the Yangtze-Hydro environmental program, financed by the German Ministry of Education and Science. In order to test combinations of environmental factors like nutrients and pollution, we use an integrated modeling approach to study the potential accumulation and biomagnification. We describe the integrative modeling approach and the consecutive adaption of the AQUATOX model, used as modeling framework for ecological risk assessment. As a starting point, pre-calibrated simulations were adapted to Yangtze-specific conditions (regionalization). Two exemplary food webs were developed by a thorough review of the pertinent literature. The first typical for the flowing conditions of the original Yangtze River and the Daning River near the city of Wushan, and the second for the stagnant reservoir characteristics of the aforementioned region that is marked by an intermediate between lake and large river communities of aquatic organisms. In close cooperation with German and Chinese partners of the Yangtze-Hydro Research Association, other site-specific parameters were estimated. The MINIBAT project contributed to the calibration of physicochemical and bathymetric parameters, and the TRANSMIC project delivered

Cancer prevention.

Science.gov (United States)

Tubiana, M

1999-01-01

Over 70% of human cancers are associated with lifestyle and about half of cancer deaths could be prevented by relatively simple individual actions: no smoking, moderate consumption of alcohol, increased consumption of fruit and vegetables, avoidance of sunbathing, obesity and a too high consumption of saturated lipids. Most of these efforts would also markedly decrease the incidence of cardiovascular and respiratory diseases. However, the concept of prevention is currently neither well accepted nor understood by the medical community and the general public. It is often felt that it restricts freedom, imposes a choice between pleasure and duty, and that passing judgement on lifestyle is a form of intolerance. The case of tobacco illustrates the difficulties encountered by prevention, notably among adolescents. The fight against smoking requires information, a societal approach (ban on advertising, increase in price), and a reduction of the example given by adult smoking (parents, peers, teachers, physicians, TV presenters, movie stars, have a great influence on adolescents), while tobacco cessation programs must be promoted. The various approaches should be integrated into a global program of health prevention, including health education at school from 5 to 12 years of age. The efficacy of each of the global program's components should be evaluated. Misconceptions such as overestimation of the impact of pollution on health should also be corrected. Health is created and experienced by people within the setting of their daily lives, in particular during childhood. Prevention is the responsibility of individual members of the community but also of the community as a whole.

Design of Polymeric Nanofiber Gauze Mask to Prevent Inhaling PM2.5 Particles from Haze Pollution

Directory of Open Access Journals (Sweden)

Xingzhou Li

2015-01-01

Full Text Available Recently, PM2.5 (particulate matter with diameter of 2.5 micron or less has become a major health hazard from the polluted air in many cities in China. The regular gauze masks are used to prevent inhaling the PM2.5 fine particles; however, those masks are not able to filter out the PM2.5 because of the large porosity of the mask materials. Some well-prevented masks usually have poor breathability, which increases other health risks. In this study, a polysulfone based nanofiber for mask filtration material was synthesized by electrospinning. That nanofiber mask material was characterized by SEM, air permeability test, and PM2.5 trapping experiment. The results indicate that nanofiber mask material can efficiently filter out the PM2.5 particles and simultaneously preserve a good breathability. We attribute such improvement to the nanoscaled fibers, having the same porosity as that of regular gauze mask but with extremely reduced local interfiber space.

Integrated biomass gasification using the waste heat from hot slags: Control of syngas and polluting gas releases

International Nuclear Information System (INIS)

Sun, Yongqi; Seetharaman, Seshadri; Liu, Qianyi; Zhang, Zuotai; Liu, Lili; Wang, Xidong

2016-01-01

In this study, the thermodynamics of a novel strategy, i.e., biomass/CO 2 gasification integrated with heat recovery from hot slags in the steel industry, were systemically investigated. Both the target syngas yield and the polluting gas release were considered where the effect of gasifying conditions including temperature, pressure and CO 2 reacted was analyzed and then the roles of hot slags were further clarified. The results indicated that there existed an optimum temperature for the maximization of H 2 production. Compared to blast furnace slags, steel slags remarkably increased the CO yield at 600–1400 °C due to the existence of iron oxides and decreased the S-containing gas releases at 400–700 °C, indicating potential desulfurizing ability. The identification of biomass/CO 2 gasification thermodynamics in presence of slags could thus provide important clues not only for the deep understanding of biomass gasification but also for the industrial application of this emerging strategy from the viewpoint of syngas optimization and pollution control. - Highlights: • Biomass/CO 2 gasification was integrated with the heat recovery from hot slags. • Both syngas yield and polluting gas release during gasification were determined. • There existed an optimum temperature for the maximization of H 2 production. • Steel slags increased CO yield at 600–1400 °C due to the existence of iron oxides. • Steel slags remarkably decreased the releases of S-containing gas at 400–700 °C.

The (cost-)effectiveness of preventive, integrated care for community-dwelling frail older people: A systematic review.

Science.gov (United States)

Looman, Wilhelmina Mijntje; Huijsman, Robbert; Fabbricotti, Isabelle Natalina

2018-04-17

Integrated care is increasingly promoted as an effective and cost-effective way to organise care for community-dwelling frail older people with complex problems but the question remains whether high expectations are justified. Our study aims to systematically review the empirical evidence for the effectiveness and cost-effectiveness of preventive, integrated care for community-dwelling frail older people and close attention is paid to the elements and levels of integration of the interventions. We searched nine databases for eligible studies until May 2016 with a comparison group and reporting at least one outcome regarding effectiveness or cost-effectiveness. We identified 2,998 unique records and, after exclusions, selected 46 studies on 29 interventions. We assessed the quality of the included studies with the Effective Practice and Organization of Care risk-of-bias tool. The interventions were described following Rainbow Model of Integrated Care framework by Valentijn. Our systematic review reveals that the majority of the reported outcomes in the studies on preventive, integrated care show no effects. In terms of health outcomes, effectiveness is demonstrated most often for seldom-reported outcomes such as well-being. Outcomes regarding informal caregivers and professionals are rarely considered and negligible. Most promising are the care process outcomes that did improve for preventive, integrated care interventions as compared to usual care. Healthcare utilisation was the most reported outcome but we found mixed results. Evidence for cost-effectiveness is limited. High expectations should be tempered given this limited and fragmented evidence for the effectiveness and cost-effectiveness of preventive, integrated care for frail older people. Future research should focus on unravelling the heterogeneity of frailty and on exploring what outcomes among frail older people may realistically be expected. © 2018 The Authors. Health and Social Care in the Community

Path-integral method for the source apportionment of photochemical pollutants

Science.gov (United States)

Dunker, A. M.

2015-06-01

A new, path-integral method is presented for apportioning the concentrations of pollutants predicted by a photochemical model to emissions from different sources. A novel feature of the method is that it can apportion the difference in a species concentration between two simulations. For example, the anthropogenic ozone increment, which is the difference between a simulation with all emissions present and another simulation with only the background (e.g., biogenic) emissions included, can be allocated to the anthropogenic emission sources. The method is based on an existing, exact mathematical equation. This equation is applied to relate the concentration difference between simulations to line or path integrals of first-order sensitivity coefficients. The sensitivities describe the effects of changing the emissions and are accurately calculated by the decoupled direct method. The path represents a continuous variation of emissions between the two simulations, and each path can be viewed as a separate emission-control strategy. The method does not require auxiliary assumptions, e.g., whether ozone formation is limited by the availability of volatile organic compounds (VOCs) or nitrogen oxides (NOx), and can be used for all the species predicted by the model. A simplified configuration of the Comprehensive Air Quality Model with Extensions (CAMx) is used to evaluate the accuracy of different numerical integration procedures and the dependence of the source contributions on the path. A Gauss-Legendre formula using three or four points along the path gives good accuracy for apportioning the anthropogenic increments of ozone, nitrogen dioxide, formaldehyde, and nitric acid. Source contributions to these increments were obtained for paths representing proportional control of all anthropogenic emissions together, control of NOx emissions before VOC emissions, and control of VOC emissions before NOx emissions. There are similarities in the source contributions from the

Diving center contribution in preventing radioactive pollution

International Nuclear Information System (INIS)

Rus, Simona; Flesteriu, Catalin; Diaconu, Mihai

2004-01-01

Applying and developing constructive environment protection measures offers real and long lasting solutions that consolidate our future. In this context the Diving Center contribution in preventing radioactive pollution is enrolled. Our Center performed high quality services with authorised personal. Using their rich human, technological and scientific resources, the armed forces in general and our unity in this case, plays already an important role in supporting the development and natural environment, but results could be even greater and of high impact if the military and civilian requirements would be aligned, valorizing the qualified resources belonging to the military. The environment protection measures are an essential component of the sustainable development, which correctly and duly applied may provide a necessary and realistic option in the eternal confrontation between human activity and correct exploitation of environment. During pressure tests performed over years at the nuclear reactor from Cernavoda, the divers provided: - pressure test at Unit 1 reactor containment (test performed at a pressure of 128 kPa) in order to evaluate the loss rate; - solving previous problems of the sealing system of reactor containment and tracks of electrical cables, pipes, etc; - providing safety procedures for the Cernavoda NPP specialised personnel, after their entering the working area through the small transfer gate; - technical assistance and first aid in case of diving accidents, using the bi-place chamber (fitted with medication transfer sass) provided on site; - supervising the enforcement of legal procedures concerning training, organising and work protection in diving activities; - in case of a collective decompression accident, we had the responsibility to provide necessary treatment of personnel affected in the hyperbaric laboratory. All these activities, even though developed for specific military requirements, may satisfy the saving and protecting needs

An integrated production, inventory and preventive maintenance model for a multi-product production system

International Nuclear Information System (INIS)

Liu, Xuejuan; Wang, Wenbin; Peng, Rui

2015-01-01

This paper considers a production system that can produce multiple products alternately. Products go through the system in a sequence and a complete run of all products forms a production cycle. An integrated production, inventory and preventive maintenance model is constructed, which is characterized by the delay-time concept. Two different situations are studied based on whether the unqualified products and downtime caused by the failures of the system, set-up and preventive maintenance can be ignored or not. Three cases are considered for each situation, depending on the position of the preventive maintenance epochs: the first case, where preventive maintenance is carried out at the end of each production cycle; the second case, where preventive maintenance is carried out at each set-up time of the products; and the third case, where preventive maintenance is carried out at some set-up times only, since it may not always be optimal to carry out preventive maintenance at the end of the production cycle or at each set-up time. The modeling objectives are to find the optimal number of production cycles per year and the optimal position of preventive maintenance that will maximize the expected profit per unit time. Numerical examples, using real data, are presented to illustrate the model. - Highlights: • We propose an integrated economic production quantity and preventive maintenance model. • The situation that multiple products are produced on the same system alternately is studied. • Two situations are studied based on whether the downtime and the product quality can be ignored or not. • We use enumeration method and analytical method to select the optimal preventive maintenance policy, respectively. • We use the delay-time concept to model the preventive maintenance policy

Environmental Restoration Program pollution prevention checklist guide for the feasibility study project phase

International Nuclear Information System (INIS)

1993-09-01

Feasibility studies (FS) determine what remedial alternatives are presented to regulators for site cleanup. A key consideration in this process is the waste to be generated. Minimizing the volume and toxicity of this waste will ultimately contribute to the selection of the best remedial option. The purpose of this checklist guide is to assist the user in incorporating pollution prevention/waste minimization (PP/WM) in all FS phase projects of the Environmental Restoration (ER) Program. This guide will help users document PP/WM activities for technology transfer and reporting requirements. Automated computer screens will be created from the checklist data to assist users with implementing and evaluating waste reduction. Users can then establish numerical performance measures to measure progress in planning, training, self-assessments, field implementation, documentation, and technology transfer. Cost savings result as users train and assess themselves and perform preliminary waste assessments

Control and prevention of industrial air pollution: Special issue; Bestrijding en preventie van industriele luchtverontreiniging: Thema

Energy Technology Data Exchange (ETDEWEB)

Waque, W.P.G.M. [Bureau Vergunningen en Bedrijven, DCMR Milieudienst Rijnmond, Schiedam (Netherlands); Zijlstra, W.M. [Bureau Milieu en Ruimtelijke Ordening, VNO/NCW, The Hague (Netherlands); Buisman, C.J.N.; Dijkman, H. [Paques, Balk (Netherlands); Prins, W.L.; Verbraak, P. [Biostar Development, Balk (Netherlands); Den Hartog, A.J. [Hoogovens Corporate Research Laboratorium, IJmuiden (Netherlands); Jol, A. [Sector Milieutechnologie, DHV Milieu en Infrastructuur, Amersfoort (Netherlands); Van Ham, J. [ed.

1994-12-01

In four articles in this special issue of the magazine attention is paid to new techniques by which emissions to the air from the industry can be controlled and/or prevented. In the first article an overview is given of sources of air pollution, caused by dust. In the second article intermediate results of the KWS 2000 program (aimed at 50% reduction of the emission of volatile organic matter for the year 2000) are outlined. In the third article a cooperative biological (flue) gas desulfurization pilot plant project is discussed. In the fourth and last article the most important possible techniques to reduce the emission of volatile organic matter are highlighted

Understanding environmental pollution: a primer. 2nd ed.

Energy Technology Data Exchange (ETDEWEB)

Marquita K. Hill [University of Maine, Orono, MN (United States)

2004-08-15

The book moves from the definition of pollution and how pollutants behave, to air and water pollution basics, pollution and global change, solid waste, and pollution in the home. It also discusses persistent and bioaccumulative chemicals, and pesticides, and it places greater stress on global pollutants. The relationship between energy generation and use, and pollution is stressed, as well as the importance of going beyond pollution control, to pollution prevention. Impacts on human and environmental health are emphasized throughout. Contents are: 1. Understanding pollution; 2. Reducing pollution; 3. Chemical toxicity; 4. Chemical exposures and risk assessment; 5. Ambient air pollution; 6. Acid deposition; 7. Global climate change; 8. Stratispheric ozone depletion; 9. Water pollution; 10. Drinking water; 11. Solid waste; 12. Hazardous waste; 13. Energy; 14. Persistent, bioaccumulative and toxic; 15. Metals; 16. Pesticides; 17. Pollution at home; and 18. Zero waste, zero emissions. 69 figs., 42 tabs.

Identification of Major Risk Sources for Surface Water Pollution by Risk Indexes (RI) in the Multi-Provincial Boundary Region of the Taihu Basin, China.

Science.gov (United States)

Yao, Hong; Li, Weixin; Qian, Xin

2015-08-21

Environmental safety in multi-district boundary regions has been one of the focuses in China and is mentioned many times in the Environmental Protection Act of 2014. Five types were categorized concerning the risk sources for surface water pollution in the multi-provincial boundary region of the Taihu basin: production enterprises, waste disposal sites, chemical storage sites, agricultural non-point sources and waterway transportations. Considering the hazard of risk sources, the purification property of environmental medium and the vulnerability of risk receptors, 52 specific attributes on the risk levels of each type of risk source were screened out. Continuous piecewise linear function model, expert consultation method and fuzzy integral model were used to calculate the integrated risk indexes (RI) to characterize the risk levels of pollution sources. In the studied area, 2716 pollution sources were characterized by RI values. There were 56 high-risk sources screened out as major risk sources, accounting for about 2% of the total. The numbers of sources with high-moderate, moderate, moderate-low and low pollution risk were 376, 1059, 101 and 1124, respectively, accounting for 14%, 38%, 5% and 41% of the total. The procedure proposed could be included in the integrated risk management systems of the multi-district boundary region of the Taihu basin. It could help decision makers to identify major risk sources in the risk prevention and reduction of surface water pollution.

Integrating multiple fish biomarkers and risk assessment as indicators of metal pollution along the Red Sea coast of Hodeida, Yemen Republic.

Science.gov (United States)

Omar, Wael A; Saleh, Yousef S; Marie, Mohamed-Assem S

2014-12-01

The marine environment of the Red Sea coast of Yemen Republic is subjected to increasing anthropogenic activities. The present field study assesses the impacts of metal pollutants on two common marine fish species; Pomadasys hasta and Lutjanus russellii collected from a reference site in comparison to two polluted sites along the Red Sea coast of Hodeida, Yemen Republic. Concentrations of heavy metals (Fe, Cu, Zn, Cd and Pb) in fish vital organs, metal pollution index (MPI), indicative biochemical parameters of liver functions (alanine aminotransferase [ALT] and aspartate aminotransferase [AST]) and kidney functions (urea and creatinine) as well as histopathological changes in gills, liver and kidney of both fish species are integrated as biomarkers of metal pollution. These biomarkers showed species-specific and/or site-specific response. The hazard index (HI) was used as an indicator of human health risks associated with fish consumption. The detected low HI values in most cases doesn't neglect the fact that the cumulative risk effects for metals together give an alarming sign and that the health of fish consumers is endangered around polluted sites. The levels of ALT, AST and urea in plasma of both fish species collected from the polluted sites showed significant increase in comparison to those of reference site. Histopathological alterations and evident damage were observed in tissues of fish collected from the polluted sites. The investigated set of biomarkers proved to be efficient and reliable in biomonitoring the pollution status along different pollution gradients. Copyright © 2014 Elsevier Inc. All rights reserved.

Pollution control in pulp and paper industrial effluents using integrated chemical-biological treatment sequences.

Science.gov (United States)