WorldWideScience

Sample records for integrated multidisciplinary design

  1. Multi-disciplinary coupling for integrated design of propulsion systems

    Science.gov (United States)

    Chamis, C. C.; Singhal, S. N.

    1993-01-01

    Effective computational simulation procedures are described for modeling the inherent multi-disciplinary interactions for determining the true response of propulsion systems. Results are presented for propulsion system responses including multi-discipline coupling effects via (1) coupled multi-discipline tailoring, (2) an integrated system of multidisciplinary simulators, (3) coupled material-behavior/fabrication-process tailoring, (4) sensitivities using a probabilistic simulator, and (5) coupled materials/structures/fracture/probabilistic behavior simulator. The results show that the best designs can be determined if the analysis/tailoring methods account for the multi-disciplinary coupling effects. The coupling across disciplines can be used to develop an integrated interactive multi-discipline numerical propulsion system simulator.

  2. Integrating Multibody Simulation and CFD: toward Complex Multidisciplinary Design Optimization

    Science.gov (United States)

    Pieri, Stefano; Poloni, Carlo; Mühlmeier, Martin

    This paper describes the use of integrated multidisciplinary analysis and optimization of a race car model on a predefined circuit. The objective is the definition of the most efficient geometric configuration that can guarantee the lowest lap time. In order to carry out this study it has been necessary to interface the design optimization software modeFRONTIER with the following softwares: CATIA v5, a three dimensional CAD software, used for the definition of the parametric geometry; A.D.A.M.S./Motorsport, a multi-body dynamic simulation software; IcemCFD, a mesh generator, for the automatic generation of the CFD grid; CFX, a Navier-Stokes code, for the fluid-dynamic forces prediction. The process integration gives the possibility to compute, for each geometrical configuration, a set of aerodynamic coefficients that are then used in the multiboby simulation for the computation of the lap time. Finally an automatic optimization procedure is started and the lap-time minimized. The whole process is executed on a Linux cluster running CFD simulations in parallel.

  3. Multi-disciplinary coupling effects for integrated design of propulsion systems

    Science.gov (United States)

    Chamis, C. C.; Singhal, S. N.

    1993-01-01

    Effective computational simulation procedures are described for modeling the inherent multi-disciplinary interactions which govern the accurate response of propulsion systems. Results are presented for propulsion system responses including multi-disciplinary coupling effects using coupled multi-discipline thermal, structural, and acoustic tailoring; an integrated system of multi-disciplinary simulators; coupled material behavior/fabrication process tailoring; sensitivities using a probabilistic simulator; and coupled materials, structures, fracture, and probabilistic behavior simulator. The results demonstrate that superior designs can be achieved if the analysis/tailoring methods account for the multi-disciplinary coupling effects. The coupling across disciplines can be used to develop an integrated coupled multi-discipline numerical propulsion system simulator.

  4. Integrating Multidisciplinary Engineering Knowledge

    Science.gov (United States)

    Wolff, Karin; Luckett, Kathy

    2013-01-01

    In order to design two distinct engineering qualification levels for an existing University of Technology programme, empirical evidence based on the current diploma is necessary to illuminate the nature of and the relationship between the "contextual" and "conceptual" elements underpinning a multidisciplinary engineering…

  5. A conceptual design of multidisciplinary-integrated C.F.D. simulation on parallel computers

    International Nuclear Information System (INIS)

    Onishi, Ryoichi; Ohta, Takashi; Kimura, Toshiya.

    1996-11-01

    A design of a parallel aeroelastic code for aircraft integrated simulations is conducted. The method for integrating aerodynamics and structural dynamics software on parallel computers is devised by using the Euler/Navier-Stokes equations coupled with wing-box finite element structures. A synthesis of modern aircraft requires the optimizations of aerodynamics, structures, controls, operabilities, or other design disciplines, and the R and D efforts to implement Multidisciplinary Design Optimization environments using high performance computers are made especially among the U.S. aerospace industries. This report describes a Multiple Program Multiple Data (MPMD) parallelization of aerodynamics and structural dynamics codes with a dynamic deformation grid. A three-dimensional computation of a flowfield with dynamic deformation caused by a structural deformation is performed, and a pressure data calculated is used for a computation of the structural deformation which is input again to a fluid dynamics code. This process is repeated exchanging the computed data of pressures and deformations between flowfield grids and structural elements. It enables to simulate the structure movements which take into account of the interaction of fluid and structure. The conceptual design for achieving the aforementioned various functions is reported. Also the future extensions to incorporate control systems, which enable to simulate a realistic aircraft configuration to be a major tool for Aircraft Integrated Simulation, are investigated. (author)

  6. An architecture for integration of multidisciplinary models

    DEFF Research Database (Denmark)

    Belete, Getachew F.; Voinov, Alexey; Holst, Niels

    2014-01-01

    Integrating multidisciplinary models requires linking models: that may operate at different temporal and spatial scales; developed using different methodologies, tools and techniques; different levels of complexity; calibrated for different ranges of inputs and outputs, etc. On the other hand......, Enterprise Application Integration, and Integration Design Patterns. We developed an architecture of a multidisciplinary model integration framework that brings these three aspects of integration together. Service-oriented-based platform independent architecture that enables to establish loosely coupled...

  7. Integrated Multidisciplinary Optimization Objects

    Science.gov (United States)

    Alston, Katherine

    2014-01-01

    OpenMDAO is an open-source MDAO framework. It is used to develop an integrated analysis and design environment for engineering challenges. This Phase II project integrated additional modules and design tools into OpenMDAO to perform discipline-specific analysis across multiple flight regimes at varying levels of fidelity. It also showcased a refined system architecture that allows the system to be less customized to a specific configuration (i.e., system and configuration separation). By delivering a capable and validated MDAO system along with a set of example applications to be used as a template for future users, this work greatly expands NASA's high-fidelity, physics-based MDAO capabilities and enables the design of revolutionary vehicles in a cost-effective manner. This proposed work complements M4 Engineering's expertise in developing modeling and simulation toolsets that solve relevant subsonic, supersonic, and hypersonic demonstration applications.

  8. Integration of Multifidelity Multidisciplinary Computer Codes for Design and Analysis of Supersonic Aircraft

    Science.gov (United States)

    Geiselhart, Karl A.; Ozoroski, Lori P.; Fenbert, James W.; Shields, Elwood W.; Li, Wu

    2011-01-01

    This paper documents the development of a conceptual level integrated process for design and analysis of efficient and environmentally acceptable supersonic aircraft. To overcome the technical challenges to achieve this goal, a conceptual design capability which provides users with the ability to examine the integrated solution between all disciplines and facilitates the application of multidiscipline design, analysis, and optimization on a scale greater than previously achieved, is needed. The described capability is both an interactive design environment as well as a high powered optimization system with a unique blend of low, mixed and high-fidelity engineering tools combined together in the software integration framework, ModelCenter. The various modules are described and capabilities of the system are demonstrated. The current limitations and proposed future enhancements are also discussed.

  9. An experiment in multidisciplinary digital design

    NARCIS (Netherlands)

    Tuncer, B.; De Ruiter, P.; Mulders, S.

    2008-01-01

    The design and realization of complex buildings requires multidisciplinary design collaboration from early on in the design process. The intensive use of digital design environments in this process demands new knowledge and skills from the involved players including integrating and managing digital

  10. Adopting a Design-Thinking Multidisciplinary Learning Approach: Integrating Mobile Applications into a Marketing Research Course

    Science.gov (United States)

    Zarzosa, Jennifer

    2018-01-01

    This article seeks to address the gap between marketing education and marketing practice by integrating a design-thinking (DT) methodology to the marketing research (MR) framework to achieve learning objectives that will enhance cross-functional, collaborative, conceptual, and technical skills. The mobile application marketing research project…

  11. Integrated, multidisciplinary care for hand eczema: design of a randomized controlled trial and cost-effectiveness study

    Directory of Open Access Journals (Sweden)

    Boot Cécile RL

    2009-12-01

    Full Text Available Abstract Background The individual and societal burden of hand eczema is high. Literature indicates that moderate to severe hand eczema is a disease with a poor prognosis. Many patients are hampered in their daily activities, including work. High costs are related to high medical consumption, productivity loss and sick leave. Usual care is suboptimal, due to a lack of optimal instruction and coordination of care, and communication with the general practitioner/occupational physician and people involved at the workplace. Therefore, an integrated, multidisciplinary intervention involving a dermatologist, a care manager, a specialized nurse and a clinical occupational physician was developed. This paper describes the design of a study to investigate the effectiveness and cost-effectiveness of integrated care for hand eczema by a multidisciplinary team, coordinated by a care manager, consisting of instruction on avoiding relevant contact factors, both in the occupational and in the private environment, optimal skin care and treatment, compared to usual, dermatologist-led care. Methods The study is a multicentre, randomized, controlled trial with an economic evaluation alongside. The study population consists of patients with chronic, moderate to severe hand eczema, who visit an outpatient clinic of one of the participating 5 (three university and two general hospitals. Integrated, multidisciplinary care, coordinated by a care manager, including allergo-dermatological evaluation by a dermatologist, occupational intervention by a clinical occupational physician, and counselling by a specialized nurse on optimizing topical treatment and skin care will be compared with usual care by a dermatologist. The primary outcome measure is the cumulative difference in reduction of the clinical severity score HECSI between the groups. Secondary outcome measures are the patient's global assessment, specific quality of life with regard to the hands, generic quality

  12. Initial Multidisciplinary Design and Analysis Framework

    Science.gov (United States)

    Ozoroski, L. P.; Geiselhart, K. A.; Padula, S. L.; Li, W.; Olson, E. D.; Campbell, R. L.; Shields, E. W.; Berton, J. J.; Gray, J. S.; Jones, S. M.; hide

    2010-01-01

    Within the Supersonics (SUP) Project of the Fundamental Aeronautics Program (FAP), an initial multidisciplinary design & analysis framework has been developed. A set of low- and intermediate-fidelity discipline design and analysis codes were integrated within a multidisciplinary design and analysis framework and demonstrated on two challenging test cases. The first test case demonstrates an initial capability to design for low boom and performance. The second test case demonstrates rapid assessment of a well-characterized design. The current system has been shown to greatly increase the design and analysis speed and capability, and many future areas for development were identified. This work has established a state-of-the-art capability for immediate use by supersonic concept designers and systems analysts at NASA, while also providing a strong base to build upon for future releases as more multifidelity capabilities are developed and integrated.

  13. Design of high performance mechatronics high-tech functionality by multidisciplinary system integration

    CERN Document Server

    Munnig Schmidt, R; Rankers, A

    2014-01-01

    Since they entered our world around the middle of the 20th century, the application of mechatronics has enhanced our lives with functionality based on the integration of electronics, control systems and electric drives.This book deals with the special class of mechatronics that has enabled the exceptional levels of accuracy and speed of high-tech equipment applied in the semiconductor industry, realising the continuous shrink in detailing of micro-electronics and MEMS.As well as the more frequently presented standard subjects of dynamics, motion control, electronics and electromechanics, this

  14. The design of high performance mechatronics high-tech functionality by multidisciplinary system integration

    CERN Document Server

    Munnig Schmidt, R; van Eijk, J

    2011-01-01

    Since they entered our world around the middle of the 20th century, the application of mechatronics has enhanced our lives with functionality based on the integration of electronics, control systems and electric drives. This book deals with the special class of mechatronics that has enabled the exceptional levels of accuracy and speed of high-tech equipment applied in the semiconductor industry, realising the continuous shrink in detailing of micro-electronics and MEMS. As well as the more frequently presented standard subjects of dynamics, motion control, electronics and electromechanics, thi

  15. Optimal Design of Integrated Systems Health Management (ISHM) Systems for improving safety in NASA's Exploration Vehicles: A Two-Level Multidisciplinary Design Approach

    Science.gov (United States)

    Mehr, Ali Farhang; Tumer, Irem; Barszcz, Eric

    2005-01-01

    Integrated Vehicle Health Management (ISHM) systems are used to detect, assess, and isolate functional failures in order to improve safety of space systems such as Orbital Space Planes (OSPs). An ISHM system, as a whole, consists of several subsystems that monitor different components of an OSP including: Spacecraft, Launch Vehicle, Ground Control, and the International Space Station. In this research, therefore, we propose a new methodology to design and optimize ISHM as a distributed system with multiple disciplines (that correspond to different subsystems of OSP safety). A paramount amount of interest has been given in the literature to the multidisciplinary design optimization of problems with such architecture (as will be reviewed in the full paper).

  16. Developing a Collaborative Multidisciplinary Online Design Course

    Directory of Open Access Journals (Sweden)

    Diane M. Bender, Ph.D.

    2005-07-01

    Full Text Available Technology is transforming the practice of architecture and design from the conceptual stages right down to the actual construction. One would assume technology is being readily integrated into current design education. Unfortunately, this is not the case. The purpose of this study is to explore the integration of online education into the curriculum of architecture and design. The three primary obstacles to integrating technology with education in these disciplines are identified as: 1 the limited evidence of online education in the fields of architecture and design (Sagun, Demirkan, & Goktepe, 2001; 2 the reluctance of design educators to teach in an online environment (Bender & Good, 2003; and 3 the lack of multidisciplinary coursework currently available between architecture, design, and other related fields (IIDA Report, 1998. This paper will discuss online education in the context of traditional architecture and design studio instruction. A case study of the development of a collaborative, multidisciplinary online course offered between five major universities will be presented as a catalyst for change. The paper concludes with reflections on the pedagogical advantages and disadvantages of this new educational model and its implications for instructors involved in online education.

  17. Integrated Multidisciplinary Optimization Objects, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — M4 Engineering proposes to implement physics-based, multidisciplinary analysis and optimization objects that will be integrated into a Python, open-source framework...

  18. Multi-Disciplinary Design Optimization Using WAVE

    Science.gov (United States)

    Irwin, Keith

    2000-01-01

    The current preliminary design tools lack the product performance, quality and cost prediction fidelity required to design Six Sigma products. They are also frequently incompatible with the tools used in detailed design, leading to a great deal of rework and lost or discarded data in the transition from preliminary to detailed design. Thus, enhanced preliminary design tools are needed in order to produce adequate financial returns to the business. To achieve this goal, GEAE has focused on building the preliminary design system around the same geometric 3D solid model that will be used in detailed design. With this approach, the preliminary designer will no longer convert a flowpath sketch into an engine cross section but rather, automatically create 3D solid geometry for structural integrity, life, weight, cost, complexity, producibility, and maintainability assessments. Likewise, both the preliminary design and the detailed design can benefit from the use of the same preliminary part sizing routines. The design analysis tools will also be integrated with the 3D solid model to eliminate manual transfer of data between programs. GEAE has aggressively pursued the computerized control of engineering knowledge for many years. Through its study and validation of 3D CAD programs and processes, GEAE concluded that total system control was not feasible at that time. Prior CAD tools focused exclusively on detail part geometry and Knowledge Based Engineering systems concentrated on rules input and data output. A system was needed to bridge the gap between the two to capture the total system. With the introduction of WAVE Engineering from UGS, the possibilities of an engineering system control device began to formulate. GEAE decided to investigate the new WAVE functionality to accomplish this task. NASA joined GEAE in funding this validation project through Task Order No. 1. With the validation project complete, the second phase under Task Order No. 2 was established to

  19. Multidisciplinary design of electrical drives

    Energy Technology Data Exchange (ETDEWEB)

    Blaabjerg, F.; Rasmussen, P.O.; Pedersen, J.K.

    1999-07-01

    Traditionally, simulation tools for drives can simulate electrical parameters, torque and different loads. Those parameters are in many cases appropriate. However, power electronics in drives will also influence on torque ripple, temperature, vibration and acoustical noise from the motor and it is necessary to include those phenomena in the next generation of simulation tools for electrical drives. This paper describes a new design program where acoustic noise of electromagnetic origin can be simulated and even be heard by the motor and drives designer. The design program is based on a simple vibrational/acoustic model where the parameters can be calculated based on the geometry of the motor. Examples of vibrational/acoustical modelling are included and verified in both time and frequency domain. Special emphasis is on the switched reluctance motor. (au)

  20. A Web-Based Monitoring System for Multidisciplinary Design Projects

    Science.gov (United States)

    Rogers, James L.; Salas, Andrea O.; Weston, Robert P.

    1998-01-01

    In today's competitive environment, both industry and government agencies are under pressure to reduce the time and cost of multidisciplinary design projects. New tools have been introduced to assist in this process by facilitating the integration of and communication among diverse disciplinary codes. One such tool, a framework for multidisciplinary computational environments, is defined as a hardware and software architecture that enables integration, execution, and communication among diverse disciplinary processes. An examination of current frameworks reveals weaknesses in various areas, such as sequencing, displaying, monitoring, and controlling the design process. The objective of this research is to explore how Web technology, integrated with an existing framework, can improve these areas of weakness. This paper describes a Web-based system that optimizes and controls the execution sequence of design processes; and monitors the project status and results. The three-stage evolution of the system with increasingly complex problems demonstrates the feasibility of this approach.

  1. Integrated Multidisciplinary Design of High Pressure Multistage Compressor Systems (la Conception integree des compresseurs multi-etage a haute performance)

    Science.gov (United States)

    1998-09-01

    development ONERA and SNECMA and is described in [Nicoud, 91]. This methodology [ Karadimas , 1997]. The aim of all efforts method solves the Quasi-3D...computer power, 1994 2-11 BERTHILLIER, M., DUPONT, C., MONDAL, R., KARADIMAS , G. : New Ways for the Design the BARRAU, J.J. : Blade Forced Response

  2. ASTROS: A multidisciplinary automated structural design tool

    Science.gov (United States)

    Neill, D. J.

    1989-01-01

    ASTROS (Automated Structural Optimization System) is a finite-element-based multidisciplinary structural optimization procedure developed under Air Force sponsorship to perform automated preliminary structural design. The design task is the determination of the structural sizes that provide an optimal structure while satisfying numerous constraints from many disciplines. In addition to its automated design features, ASTROS provides a general transient and frequency response capability, as well as a special feature to perform a transient analysis of a vehicle subjected to a nuclear blast. The motivation for the development of a single multidisciplinary design tool is that such a tool can provide improved structural designs in less time than is currently needed. The role of such a tool is even more apparent as modern materials come into widespread use. Balancing conflicting requirements for the structure's strength and stiffness while exploiting the benefits of material anisotropy is perhaps an impossible task without assistance from an automated design tool. Finally, the use of a single tool can bring the design task into better focus among design team members, thereby improving their insight into the overall task.

  3. Integrated Multidisciplinary Constrained Optimization of Offshore Support Structures

    International Nuclear Information System (INIS)

    Haghi, Rad; Molenaar, David P; Ashuri, Turaj; Van der Valk, Paul L C

    2014-01-01

    In the current offshore wind turbine support structure design method, the tower and foundation, which form the support structure are designed separately by the turbine and foundation designer. This method yields a suboptimal design and it results in a heavy, overdesigned and expensive support structure. This paper presents an integrated multidisciplinary approach to design the tower and foundation simultaneously. Aerodynamics, hydrodynamics, structure and soil mechanics are the modeled disciplines to capture the full dynamic behavior of the foundation and tower under different environmental conditions. The objective function to be minimized is the mass of the support structure. The model includes various design constraints: local and global buckling, modal frequencies, and fatigue damage along different stations of the structure. To show the usefulness of the method, an existing SWT-3.6-107 offshore wind turbine where its tower and foundation are designed separately is used as a case study. The result of the integrated multidisciplinary design optimization shows 12.1% reduction in the mass of the support structure, while satisfying all the design constraints

  4. Robust Parameter Coordination for Multidisciplinary Design

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    This paper introduced a robust parameter coordination method to analyze parameter uncertainties so as to predict conflicts and coordinate parameters in multidisciplinary design. The proposed method is based on constraints network, which gives a formulated model to analyze the coupling effects between design variables and product specifications. In this model, interval boxes are adopted to describe the uncertainty of design parameters quantitatively to enhance the design robustness. To solve this constraint network model, a general consistent algorithm framework is designed and implemented with interval arithmetic and the genetic algorithm, which can deal with both algebraic and ordinary differential equations. With the help of this method, designers could infer the consistent solution space from the given specifications. A case study involving the design of a bogie dumping system demonstrates the usefulness of this approach.

  5. Multidisciplinary systems engineering architecting the design process

    CERN Document Server

    Crowder, James A; Demijohn, Russell

    2016-01-01

    This book presents Systems Engineering from a modern, multidisciplinary engineering approach, providing the understanding that all aspects of systems design, systems, software, test, security, maintenance and the full life-cycle must be factored in to any large-scale system design; up front, not factored in later. It lays out a step-by-step approach to systems-of-systems architectural design, describing in detail the documentation flow throughout the systems engineering design process. It provides a straightforward look and the entire systems engineering process, providing realistic case studies, examples, and design problems that will enable students to gain a firm grasp on the fundamentals of modern systems engineering.  Included is a comprehensive design problem that weaves throughout the entire text book, concluding with a complete top-level systems architecture for a real-world design problem.

  6. Integrated Structural Design Education

    DEFF Research Database (Denmark)

    Bjerregaard Jensen, Lotte; Almegaard, Henrik

    2011-01-01

    to EU legislation. And a successful engineering student must be prepared to work in the open-ended, multidisciplinary environment necessary to produce structures which comply with EIA demands. This paper describes an innovative course developed at the Technical University of Denmark which integrates...... landscaping and structural design. The integrated courses create a setting for learning about the design of large-scale structures and involve geometry, statics, computer simulation, graphical design and landscape architecture. Together, they educate engineers who can take part in the early design phases...... of a project, function well in design teams, and comply with EU EIA demands....

  7. Design Environment for Multifidelity and Multidisciplinary Components

    Science.gov (United States)

    Platt, Michael

    2014-01-01

    One of the greatest challenges when developing propulsion systems is predicting the interacting effects between the fluid loads, thermal loads, and structural deflection. The interactions between technical disciplines often are not fully analyzed, and the analysis in one discipline often uses a simplified representation of other disciplines as an input or boundary condition. For example, the fluid forces in an engine generate static and dynamic rotor deflection, but the forces themselves are dependent on the rotor position and its orbit. It is important to consider the interaction between the physical phenomena where the outcome of each analysis is heavily dependent on the inputs (e.g., changes in flow due to deflection, changes in deflection due to fluid forces). A rigid design process also lacks the flexibility to employ multiple levels of fidelity in the analysis of each of the components. This project developed and validated an innovative design environment that has the flexibility to simultaneously analyze multiple disciplines and multiple components with multiple levels of model fidelity. Using NASA's open-source multidisciplinary design analysis and optimization (OpenMDAO) framework, this multifaceted system will provide substantially superior capabilities to current design tools.

  8. The INGECAD multidisciplinary integrated computer aided engineering system

    International Nuclear Information System (INIS)

    Kisielewicz, L.T.

    1989-01-01

    The purpose of this paper is to define the key criteria of an integrated CAE system, and to discuss the solution developed by Ingevision to match these criteria. An information flow model of process plant engineering is presented as a background to the key criteria of CAE systems. This model includes multidisciplinary interfaces and project changes up to the as-built stage. The key quality criteria of CAE systems correspond to managerial issues, such as project control, to technical issues, consistency and quality assurance, and to economical issues, such as cost optimization. The INGECAD system answers these criteria with a tripod nucleus underlying a set of specialized applications. The nucleus includes a Data Base Management System, basic Graphical Tools, and a Decision Support System. The paper overviews the different modules of the INGECAD system emphasizing the general architecture and the basic tools. Specific examples are developed in functional design, cost optimized items selection, and semi-automated routing of piping system. These examples are not intended to illustrate exhaustively the capabilities of the INGECAD system, but rather to highlight some of the advantages the multidisciplinary integration of the system provides to the users. (orig./HP)

  9. Integrated Design

    DEFF Research Database (Denmark)

    Lenau, Torben Anker

    1999-01-01

    A homepage on the internet with course material, lecture plan, student exercises, etc. Continuesly updated during the course Integrated Design (80402, 80403)......A homepage on the internet with course material, lecture plan, student exercises, etc. Continuesly updated during the course Integrated Design (80402, 80403)...

  10. The KNOMAD Methodology for Integration of Multi-Disciplinary Engineering Knowledge within Aerospace Production

    NARCIS (Netherlands)

    Curran, R.; Verhagen, W.J.C.; Van Tooren, M.J.L.

    2010-01-01

    The paper is associated with the integration of multi-disciplinary knowledge within a Knowledge Based Engineering (KBE)-enabled design framework. To support this integration effort, the KNOMAD methodology has been devised. KNOMAD stands for Knowledge Optimized Manufacture And Design and is a

  11. A Multidisciplinary Approach to Mixer-Ejector Analysis and Design

    Science.gov (United States)

    Hendricks, Eric, S.; Seidel, Jonathan, A.

    2012-01-01

    The design of an engine for a civil supersonic aircraft presents a difficult multidisciplinary problem to propulsion system engineers. There are numerous competing requirements for the engine, such as to be efficient during cruise while yet quiet enough at takeoff to meet airport noise regulations. The use of mixer-ejector nozzles presents one possible solution to this challenge. However, designing a mixer-ejector which will successfully address both of these concerns is a difficult proposition. Presented in this paper is an integrated multidisciplinary approach to the analysis and design of these systems. A process that uses several low-fidelity tools to evaluate both the performance and acoustics of mixer-ejectors nozzles is described. This process is further expanded to include system-level modeling of engines and aircraft to determine the effects on mission performance and noise near airports. The overall process is developed in the OpenMDAO framework currently being developed by NASA. From the developed process, sample results are given for a notional mixer-ejector design, thereby demonstrating the capabilities of the method.

  12. Integrated Multidisciplinary Optimization Objects, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — During Phase I, M4 Engineering integrated a prototype system into OpenMDAO, a NASA GRC open-source framework. This prototype system was a proof-of-concept that M4...

  13. Integrated Design

    DEFF Research Database (Denmark)

    Jørgensen, Michael; Nielsen, M. W.; Strømann-Andersen, Jakob Bjørn

    2011-01-01

    and describe the decision process. Specific attention is given to how the engineering input was presented and how it was able to facilitate the design development. Site and context, building shape, organization of functions and HVAC-systems were all included to obtain a complete picture of the building......, low-energy consumption, and high-quality indoor environment. We use this case study to investigate how technical knowledge about building performance can be integrated into the conceptual design stage. We have selected certain points during the design process that represented design challenges...

  14. Multidisciplinary Design Optimization for High Reliability and Robustness

    National Research Council Canada - National Science Library

    Grandhi, Ramana

    2005-01-01

    .... Over the last 3 years Wright State University has been applying analysis tools to predict the behavior of critical disciplines to produce highly robust torpedo designs using robust multi-disciplinary...

  15. An Integrated Design Process

    DEFF Research Database (Denmark)

    Petersen, Mads Dines; Knudstrup, Mary-Ann

    2010-01-01

    Present paper is placed in the discussion about how sustainable measures are integrated in the design process by architectural offices. It presents results from interviews with four leading Danish architectural offices working with sustainable architecture and their experiences with it, as well...... as the requirements they meet in terms of how to approach the design process – especially focused on the early stages like a competition. The interviews focus on their experiences with working in multidisciplinary teams and using digital tools to support their work with sustainable issues. The interviews show...... the environmental measures cannot be discarded due to extra costs....

  16. Integrated Energy Design

    DEFF Research Database (Denmark)

    Brunsgaard, Camilla; Dvořáková, Pavla; Wyckmans, Annemie

    2014-01-01

    the development, it is essential that educational institutions foster professionals with such knowledge, skills and competences. An initiative toward this direction is the EUproject of IDES-EDU: “Master and Post-Graduate education and training in multi-disciplinary teams”. The paper describes the necessity...... of more integrated and cross-disciplinary approaches to building design through state-of-the-art of the building sector and educational initiatives in the participating countries in the project, and through theory of design processes. The paper also communicates the results of newly developed cross...

  17. Transforming Multidisciplinary Customer Requirements to Product Design Specifications

    Science.gov (United States)

    Ma, Xiao-Jie; Ding, Guo-Fu; Qin, Sheng-Feng; Li, Rong; Yan, Kai-Yin; Xiao, Shou-Ne; Yang, Guang-Wu

    2017-09-01

    With the increasing of complexity of complex mechatronic products, it is necessary to involve multidisciplinary design teams, thus, the traditional customer requirements modeling for a single discipline team becomes difficult to be applied in a multidisciplinary team and project since team members with various disciplinary backgrounds may have different interpretations of the customers' requirements. A new synthesized multidisciplinary customer requirements modeling method is provided for obtaining and describing the common understanding of customer requirements (CRs) and more importantly transferring them into a detailed and accurate product design specifications (PDS) to interact with different team members effectively. A case study of designing a high speed train verifies the rationality and feasibility of the proposed multidisciplinary requirement modeling method for complex mechatronic product development. This proposed research offersthe instruction to realize the customer-driven personalized customization of complex mechatronic product.

  18. The development of a design behaviour questionnaire for multidisciplinary teams

    NARCIS (Netherlands)

    Peeters, M.A.G.; Tuijl, van H.F.J.M.; Reymen, I.M.M.J.; Rutte, C.G.

    2007-01-01

    The relationship between design behaviours and successful design task completion is studied for multidisciplinary design teams. In this research, no observational methods such as audio–visual recordings or ethnographic fieldwork were used, as often the case in design research, but a questionnaire

  19. Design of efficient and safe neural stimulators a multidisciplinary approach

    CERN Document Server

    van Dongen, Marijn

    2016-01-01

    This book discusses the design of neural stimulator systems which are used for the treatment of a wide variety of brain disorders such as Parkinson’s, depression and tinnitus. Whereas many existing books treating neural stimulation focus on one particular design aspect, such as the electrical design of the stimulator, this book uses a multidisciplinary approach: by combining the fields of neuroscience, electrophysiology and electrical engineering a thorough understanding of the complete neural stimulation chain is created (from the stimulation IC down to the neural cell). This multidisciplinary approach enables readers to gain new insights into stimulator design, while context is provided by presenting innovative design examples. Provides a single-source, multidisciplinary reference to the field of neural stimulation, bridging an important knowledge gap among the fields of bioelectricity, neuroscience, neuroengineering and microelectronics;Uses a top-down approach to understanding the neural activation proc...

  20. Research on Multidisciplinary Optimization Design of Bridge Crane

    Directory of Open Access Journals (Sweden)

    Tong Yifei

    2013-01-01

    Full Text Available Bridge crane is one of the most widely used cranes in our country, which is indispensable equipment for material conveying in the modern production. In this paper, the framework of multidisciplinary optimization for bridge crane is proposed. The presented research on crane multidisciplinary design technology for energy saving includes three levels, respectively: metal structures level, transmission design level, and electrical system design level. The shape optimal mathematical model of the crane is established for shape optimization design of metal structure level as well as size optimal mathematical model and topology optimal mathematical model of crane for topology optimization design of metal structure level is established. Finally, system-level multidisciplinary energy-saving optimization design of bridge crane is further carried out with energy-saving transmission design results feedback to energy-saving optimization design of metal structure. The optimization results show that structural optimization design can reduce total mass of crane greatly by using the finite element analysis and multidisciplinary optimization technology premised on the design requirements of cranes such as stiffness and strength; thus, energy-saving design can be achieved.

  1. Formalizing an integrative, multidisciplinary cancer therapy discovery workflow

    Science.gov (United States)

    McGuire, Mary F.; Enderling, Heiko; Wallace, Dorothy I.; Batra, Jaspreet; Jordan, Marie; Kumar, Sushil; Panetta, John C.; Pasquier, Eddy

    2014-01-01

    Although many clinicians and researchers work to understand cancer, there has been limited success to effectively combine forces and collaborate over time, distance, data and budget constraints. Here we present a workflow template for multidisciplinary cancer therapy that was developed during the 2nd Annual Workshop on Cancer Systems Biology sponsored by Tufts University, Boston, MA in July 2012. The template was applied to the development of a metronomic therapy backbone for neuroblastoma. Three primary groups were identified: clinicians, biologists, and scientists (mathematicians, computer scientists, physicists and engineers). The workflow described their integrative interactions; parallel or sequential processes; data sources and computational tools at different stages as well as the iterative nature of therapeutic development from clinical observations to in vitro, in vivo, and clinical trials. We found that theoreticians in dialog with experimentalists could develop calibrated and parameterized predictive models that inform and formalize sets of testable hypotheses, thus speeding up discovery and validation while reducing laboratory resources and costs. The developed template outlines an interdisciplinary collaboration workflow designed to systematically investigate the mechanistic underpinnings of a new therapy and validate that therapy to advance development and clinical acceptance. PMID:23955390

  2. Multidisciplinary Design and Optimization Framework for Aircraft Box Structures

    NARCIS (Netherlands)

    Van Dijk, R.E.C.; Zhao, X.; Wang, H.; Van Dalen, F.

    2012-01-01

    Competitive aircraft box structures are a perfect compromise between weight and price. The conceptual design process of these structures is a typical Multidisciplinary Design and Optimization effort, normally conducted by human engineers. The iterative nature of MDO turns development into a long and

  3. Educating engineering designers for a multidisciplinary future

    DEFF Research Database (Denmark)

    engineering design education. Educating engineering designers today significantly differs from traditional engineering education (McAloone, et.al., 2007). However, a broader view of design activities gains little attention. The project course Product/Service-Systems, which is coupled to the lecture based...... course Product life and Environmental issues at the Technical University of Denmark (DTU) and the master programme Product Development Processes at the Luleå University of Technology (LTU), Sweden, are both curriculums with a broader view than traditional (mechanical) engineering design. Based...... on these two representatives of a Scandinavian approach, the purpose in this presentation is to describe two ways of educating engineering designers to enable them to develop these broader competencies of socio-technical aspects of engineering design. Product Development Processes at LTU A process, called...

  4. Hypersonic drone vehicle design: A multidisciplinary experience

    Science.gov (United States)

    1988-01-01

    UCLA's Advanced Aeronautic Design group focussed their efforts on design problems of an unmanned hypersonic vehicle. It is felt that a scaled hypersonic drone is necesary to bridge the gap between present theory on hypersonics and the future reality of the National Aerospace Plane (NASP) for two reasons: (1) to fulfill a need for experimental data in the hypersonic regime, and (2) to provide a testbed for the scramjet engine which is to be the primary mode of propulsion for the NASP. The group concentrated on three areas of great concern to NASP design: propulsion, thermal management, and flight systems. Problem solving in these areas was directed toward design of the drone with the idea that the same design techniques could be applied to the NASP. A 70 deg swept double-delta wing configuration, developed in the 70's at the NASA Langley, was chosen as the aerodynamic and geometric model for the drone. This vehicle would be air launched from a B-1 at Mach 0.8 and 48,000 feet, rocket boosted by two internal engines to Mach 10 and 100,000 feet, and allowed to cruise under power of the scramjet engine until burnout. It would then return to base for an unpowered landing. Preliminary energy calculations based on flight requirements give the drone a gross launch weight of 134,000 pounds and an overall length of 85 feet.

  5. Hypersonic drone design: A multidisciplinary experience

    Science.gov (United States)

    1988-01-01

    Efforts were focused on design problems of an unmanned hypersonic vehicle. It is felt that a scaled hypersonic drone is necessary to bridge the gap between present theory on hypersonics and the future reality of the National Aerospace Plane (NASP) for two reasons: to fulfill a need for experimental data in the hypersonic regime, and to provide a testbed for the scramjet engine which is to be the primary mode of propulsion for the NASP. Three areas of great concern to NASP design were examined: propulsion, thermal management, and flight systems. Problem solving in these areas was directed towards design of the drone with the idea that the same design techniques could be applied to the NASP. A seventy degree swept double delta wing configuration, developed in the 70's at NASA Langley, was chosen as the aerodynamic and geometric model for the drone. This vehicle would be air-launched from a B-1 at Mach 0.8 and 48,000 feet, rocket boosted by two internal engines to Mach 10 and 100,000 feet, and allowed to cruise under power of the scramjet engine until burnout. It would then return to base for an unpowered landing. Preliminary energy calculations based upon the flight requirements give the drone a gross launch weight of 134,000 lb. and an overall length of 85 feet.

  6. Multidisciplinary management--an opportunity for service integration.

    Science.gov (United States)

    Cameron, M

    1997-01-01

    The management team of the future will enter an environment requiring facilitation, participation, clinical, and empowerment skills. Those individuals who possess a clinical orientation as well as business expertise will be sought to manage multidisciplinary units. The rapid changes in the health-care environment have forced organizations to restructure their operations. To achieve quality care, customer satisfaction, cost-effectiveness, and efficiency, service integration across the organization will be required. As we approach the 21st century, this standard will evolve until "all levels are managing patient care." Some of the restructuring trends occurring in the health-care industry have been collaboration service integration, management consolidation, and job elimination. The emphasis for the multidisciplinary manager of the future will include integrating the professional and clinical services, managing information, building community partnerships, promoting physician collaboration, and managing the change process. A model organization in the next century will move toward a people-oriented system with inclusion and empowerment initiatives. Service integration will affect all organizations, but the disciplines within the Clinical Support System will be the most affected. Future opportunities of leadership will exist for pathologists, nurses, or medical technologists as the professional silos of managers and clinicians continue to crumble.

  7. Thinking Tracks for Multidisciplinary System Design

    Directory of Open Access Journals (Sweden)

    Gerrit Maarten Bonnema

    2016-11-01

    Full Text Available Systems engineering is, for a large part, a process description of how to bring new systems to existence. It is valuable as it directs the development effort. Tools exist that can be used in this process. System analysis investigates existing and/or desired situations. However, how to create a system that instantiates the desired situation depends significantly on human creativity and insight; the required human trait here is commonly called systems thinking. In literature, this trait is regularly used, but information on how to do systems thinking is scarce. Therefore, we have introduced earlier twelve thinking tracks that are concrete and help system designers to make an optimal fit between the system under design, the identified issue, the user, the environment and the rest of the world. The paper provides the scientific rationale for the thinking tracks based on literature. Secondly, the paper presents three cases of application, leading to the conclusion that the tracks are usable and effective.

  8. Aeroelastic multidisciplinary design optimization of a swept wind turbine blade

    DEFF Research Database (Denmark)

    Pavese, Christian; Tibaldi, Carlo; Zahle, Frederik

    2017-01-01

    Mitigating loads on a wind turbine rotor can reduce the cost of energy. Sweeping blades produces a structural coupling between flapwise bending and torsion, which can be used for load alleviation purposes. A multidisciplinary design optimization (MDO) problem is formulated including the blade sweep...

  9. Systems design and engineering : facilitating multidisciplinary development projects

    NARCIS (Netherlands)

    Bonnema, Gerrit Maarten; Veenvliet, Karel; Broenink, Johannes F.

    2016-01-01

    As its name implies, the aim of Systems Design and Engineering: Facilitating Multidisciplinary Development Projects is to help systems engineers develop the skills and thought processes needed to successfully develop and implement engineered systems. Such expertise typically does not come through

  10. System Design and Engineering, lubricating multidisciplinary development projects

    NARCIS (Netherlands)

    Bonnema, Gerrit Maarten; Veenvliet, Karel; Broenink, Johannes F.

    This text book introduces systems engineering for designing systems in multidisciplinary projects. First an overview of the systems engineering process is given. Several systems thinking tracks are presented, to think about the system in a number of ways, its context, its user, its functionality,

  11. Reduced design load basis for ultimate blade loads estimation in multidisciplinary design optimization frameworks

    DEFF Research Database (Denmark)

    Pavese, Christian; Tibaldi, Carlo; Larsen, Torben J.

    2016-01-01

    The aim is to provide a fast and reliable approach to estimate ultimate blade loads for a multidisciplinary design optimization (MDO) framework. For blade design purposes, the standards require a large amount of computationally expensive simulations, which cannot be efficiently run each cost...... function evaluation of an MDO process. This work describes a method that allows integrating the calculation of the blade load envelopes inside an MDO loop. Ultimate blade load envelopes are calculated for a baseline design and a design obtained after an iteration of an MDO. These envelopes are computed...... for a full standard design load basis (DLB) and a deterministic reduced DLB. Ultimate loads extracted from the two DLBs with the two blade designs each are compared and analyzed. Although the reduced DLB supplies ultimate loads of different magnitude, the shape of the estimated envelopes are similar...

  12. A surrogate based multistage-multilevel optimization procedure for multidisciplinary design optimization

    OpenAIRE

    Yao, W.; Chen, X.; Ouyang, Q.; Van Tooren, M.

    2011-01-01

    Optimization procedure is one of the key techniques to address the computational and organizational complexities of multidisciplinary design optimization (MDO). Motivated by the idea of synthetically exploiting the advantage of multiple existing optimization procedures and meanwhile complying with the general process of satellite system design optimization in conceptual design phase, a multistage-multilevel MDO procedure is proposed in this paper by integrating multiple-discipline-feasible (M...

  13. Multidisciplinary Analysis and Optimal Design: As Easy as it Sounds?

    Science.gov (United States)

    Moore, Greg; Chainyk, Mike; Schiermeier, John

    2004-01-01

    The viewgraph presentation examines optimal design for precision, large aperture structures. Discussion focuses on aspects of design optimization, code architecture and current capabilities, and planned activities and collaborative area suggestions. The discussion of design optimization examines design sensitivity analysis; practical considerations; and new analytical environments including finite element-based capability for high-fidelity multidisciplinary analysis, design sensitivity, and optimization. The discussion of code architecture and current capabilities includes basic thermal and structural elements, nonlinear heat transfer solutions and process, and optical modes generation.

  14. Multi-Disciplinary Multi-Fidelity Design Environment, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Phoenix Integration will develop a collaborative simulation and design environment that will seamlessly integrate the people, data, and tools required for analyzing...

  15. PARAMETER COORDINATION AND ROBUST OPTIMIZATION FOR MULTIDISCIPLINARY DESIGN

    Institute of Scientific and Technical Information of China (English)

    HU Jie; PENG Yinghong; XIONG Guangleng

    2006-01-01

    A new parameter coordination and robust optimization approach for multidisciplinary design is presented. Firstly, the constraints network model is established to support engineering change, coordination and optimization. In this model, interval boxes are adopted to describe the uncertainty of design parameters quantitatively to enhance the design robustness. Secondly, the parameter coordination method is presented to solve the constraints network model, monitor the potential conflicts due to engineering changes, and obtain the consistency solution space corresponding to the given product specifications. Finally, the robust parameter optimization model is established, and genetic arithmetic is used to obtain the robust optimization parameter. An example of bogie design is analyzed to show the scheme to be effective.

  16. Health care multidisciplinary teams: The sociotechnical approach for an integrated system-wide perspective.

    Science.gov (United States)

    Marsilio, Marta; Torbica, Aleksandra; Villa, Stefano

    The current literature on the enabling conditions of multidisciplinary teams focuses on the singular dimensions of the organizations (i.e., human resources, clinical pathways, objects) without shedding light on to the way in which these organizational factors interact and mutually influence one another. Drawing on a system perspective of organizations, the authors analyze the organizational patterns that promote and support multidisciplinary teams and how they interrelate and interact to enforce the organization work system. The authors develop a modified sociotechnical system (STS) model to understand how the two dimensions of technical (devices/tools, layout/organization of space, core process standardization) and social (organizational structure, management of human resources and operations) can facilitate the implementation of multidisciplinary teams in health care. The study conducts an empirical analysis based on a sample of hospital adopters of transcatheter aortic valve implantation using the revised STS model. The modified STS model applied to the case studies improves our understanding of the critical implementation factors of a multidisciplinary approach and the importance of coordinating radical changes in the technical and the social subsystems of health care organizations. The analysis informs that the multidisciplinary effort is not a sequential process and that the interplay between the two subsystems needs to be managed efficaciously as an integrated organizational whole to deliver the goals set. Hospital managers must place equal focus on the closely interrelated technical and social dimensions by investing in (a) shared layouts and spaces that cross the boundaries of the specialized health care units, (b) standardization of the core processes through the implementation of local clinical pathways, (c) structured knowledge management mechanisms, (d) the creation of clinical directorates, and (e) the design of a planning and budgeting system that

  17. Uncertainty quantification using evidence theory in multidisciplinary design optimization

    International Nuclear Information System (INIS)

    Agarwal, Harish; Renaud, John E.; Preston, Evan L.; Padmanabhan, Dhanesh

    2004-01-01

    Advances in computational performance have led to the development of large-scale simulation tools for design. Systems generated using such simulation tools can fail in service if the uncertainty of the simulation tool's performance predictions is not accounted for. In this research an investigation of how uncertainty can be quantified in multidisciplinary systems analysis subject to epistemic uncertainty associated with the disciplinary design tools and input parameters is undertaken. Evidence theory is used to quantify uncertainty in terms of the uncertain measures of belief and plausibility. To illustrate the methodology, multidisciplinary analysis problems are introduced as an extension to the epistemic uncertainty challenge problems identified by Sandia National Laboratories. After uncertainty has been characterized mathematically the designer seeks the optimum design under uncertainty. The measures of uncertainty provided by evidence theory are discontinuous functions. Such non-smooth functions cannot be used in traditional gradient-based optimizers because the sensitivities of the uncertain measures are not properly defined. In this research surrogate models are used to represent the uncertain measures as continuous functions. A sequential approximate optimization approach is used to drive the optimization process. The methodology is illustrated in application to multidisciplinary example problems

  18. Complex multidisciplinary system composition for aerospace vehicle conceptual design

    Science.gov (United States)

    Gonzalez, Lex

    Although, there exists a vast amount of work concerning the analysis, design, integration of aerospace vehicle systems, there is no standard for how this data and knowledge should be combined in order to create a synthesis system. Each institution creating a synthesis system has in house vehicle and hardware components they are attempting to model and proprietary methods with which to model them. This leads to the fact that synthesis systems begin as one-off creations meant to answer a specific problem. As the scope of the synthesis system grows to encompass more and more problems, so does its size and complexity; in order for a single synthesis system to answer multiple questions the number of methods and method interface must increase. As a means to curtail the requirement that the increase of an aircraft synthesis systems capability leads to an increase in its size and complexity, this research effort focuses on the idea that each problem in aerospace requires its own analysis framework. By focusing on the creation of a methodology which centers on the matching of an analysis framework towards the problem being solved, the complexity of the analysis framework is decoupled from the complexity of the system that creates it. The derived methodology allows for the composition of complex multi-disciplinary systems (CMDS) through the automatic creation and implementation of system and disciplinary method interfaces. The CMDS Composition process follows a four step methodology meant to take a problem definition and progress towards the creation of an analysis framework meant to answer said problem. The unique implementation of the CMDS Composition process take user selected disciplinary analysis methods and automatically integrates them, together in order to create a syntactically composable analysis framework. As a means of assessing the validity of the CMDS Composition process a prototype system (AVDDBMS) has been developed. AVD DBMS has been used to model the

  19. Multidisciplinary Teaching-Changing Collaboration During Building Design

    DEFF Research Database (Denmark)

    Dederichs, Anne; Karlshøj, Jan

    2011-01-01

    Traditionally the design phase was carried out by one single person – the master builder. Industrialization and technical development led to a split of the role of the design master into two: the architect and the engineer. Today, demands on functionality such as energy and cost efficiency led...... to be found within on specific profession. The team-structure was generally flat and decisions were mostly made in consensus. It is worthwhile to offer a multidisciplinary course and give engineering students experience in collaboration methods....

  20. LMI–based robust controller design approach in aircraft multidisciplinary design optimization problem

    Directory of Open Access Journals (Sweden)

    Qinghua Zeng

    2015-07-01

    Full Text Available This article proposes a linear matrix inequality–based robust controller design approach to implement the synchronous design of aircraft control discipline and other disciplines, in which the variation in design parameters is treated as equivalent perturbations. Considering the complicated mapping relationships between the coefficient arrays of aircraft motion model and the aircraft design parameters, the robust controller designed is directly based on the variation in these coefficient arrays so conservative that the multidisciplinary design optimization problem would be too difficult to solve, or even if there is a solution, the robustness of design result is generally poor. Therefore, this article derives the uncertainty model of disciplinary design parameters based on response surface approximation, converts the design problem of the robust controller into a problem of solving a standard linear matrix inequality, and theoretically gives a less conservative design method of the robust controller which is based on the variation in design parameters. Furthermore, the concurrent subspace approach is applied to the multidisciplinary system with this kind of robust controller in the design loop. A multidisciplinary design optimization of a tailless aircraft as example is shown that control discipline can be synchronous optimal design with other discipline, especially this method will greatly reduce the calculated amount of multidisciplinary design optimization and make multidisciplinary design optimization results more robustness of flight performance.

  1. High-Fidelity Multidisciplinary Design Optimization of Aircraft Configurations

    Science.gov (United States)

    Martins, Joaquim R. R. A.; Kenway, Gaetan K. W.; Burdette, David; Jonsson, Eirikur; Kennedy, Graeme J.

    2017-01-01

    To evaluate new airframe technologies we need design tools based on high-fidelity models that consider multidisciplinary interactions early in the design process. The overarching goal of this NRA is to develop tools that enable high-fidelity multidisciplinary design optimization of aircraft configurations, and to apply these tools to the design of high aspect ratio flexible wings. We develop a geometry engine that is capable of quickly generating conventional and unconventional aircraft configurations including the internal structure. This geometry engine features adjoint derivative computation for efficient gradient-based optimization. We also added overset capability to a computational fluid dynamics solver, complete with an adjoint implementation and semiautomatic mesh generation. We also developed an approach to constraining buffet and started the development of an approach for constraining utter. On the applications side, we developed a new common high-fidelity model for aeroelastic studies of high aspect ratio wings. We performed optimal design trade-o s between fuel burn and aircraft weight for metal, conventional composite, and carbon nanotube composite wings. We also assessed a continuous morphing trailing edge technology applied to high aspect ratio wings. This research resulted in the publication of 26 manuscripts so far, and the developed methodologies were used in two other NRAs. 1

  2. Multi-Fidelity Multi-Strategy and Multi-Disciplinary Design Optimization Environment, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Multidisciplinary design and optimization (MDO) tools developed to perform multi-disciplinary analysis based on low fidelity computation methods have been used in...

  3. Laser and photonic systems design and integration

    CERN Document Server

    Nof, Shimon Y; Cheng, Gary J

    2014-01-01

    New, significant scientific discoveries in laser and photonic technologies, systems perspectives, and integrated design approaches can improve even further the impact in critical areas of challenge. Yet this knowledge is dispersed across several disciplines and research arenas. Laser and Photonic Systems: Design and Integration brings together a multidisciplinary group of experts to increase understanding of the ways in which systems perspectives may influence laser and photonic innovations and application integration.By bringing together chapters from leading scientists and technologists, ind

  4. Multidisciplinary integrated Parent and Child Centres in Amsterdam: a qualitative study

    Directory of Open Access Journals (Sweden)

    Vincent Busch

    2013-04-01

    Full Text Available Background: In several countries centres for the integrated delivery of services to the parent and child have been established. In the Netherlands family health care service centres, called Parent and Child Centres (PCCs involve multidisciplinary teams. Here doctors, nurses, midwives, maternity help professionals and educationists are integrated into multidisciplinary teams in neighbourhood-based centres. To date there has been little research on the implementation of service delivery in these centres.Study Design: A SWOT analysis was performed by use of triangulation data; this took place by integrating all relevant published documents on the origin and organization of the PCCs and the results from interviews with PCC experts and with PCC professionals (N=91. Structured interviews were performed with PCC-professionals (health care professionals (N=67 and PCC managers N=12 and PCC-experts (N=12 in Amsterdam and qualitatively analysed thematically. The interview themes were based on a pre-set list of codes, derived from a prior documentation study and a focus group with PCC experts. Results: Perceived advantages of PCCs were more continuity of care, shorter communication lines, low-threshold contact between professionals and promising future perspectives. Perceived challenges included the absence of uniform multidisciplinary guidelines, delays in communication with hospitals and midwives, inappropriate accommodation for effective professional integration, differing expectations regarding the PCC-manager role among PCC-partners and the danger of professionals' needs dominating clients' needs.Conclusions: Professionals perceive PCCs as a promising development in the integration of services. Remaining challenges involved improvements at the managerial and organizational level. Quantitative research into the improvements in quality of care and child health is recommended.

  5. Multidisciplinary integrated Parent and Child Centres in Amsterdam: a qualitative study

    Directory of Open Access Journals (Sweden)

    Vincent Busch

    2013-04-01

    Full Text Available Background: In several countries centres for the integrated delivery of services to the parent and child have been established. In the Netherlands family health care service centres, called Parent and Child Centres (PCCs involve multidisciplinary teams. Here doctors, nurses, midwives, maternity help professionals and educationists are integrated into multidisciplinary teams in neighbourhood-based centres. To date there has been little research on the implementation of service delivery in these centres. Study Design: A SWOT analysis was performed by use of triangulation data; this took place by integrating all relevant published documents on the origin and organization of the PCCs and the results from interviews with PCC experts and with PCC professionals (N=91. Structured interviews were performed with PCC-professionals (health care professionals (N=67 and PCC managers N=12 and PCC-experts (N=12 in Amsterdam and qualitatively analysed thematically. The interview themes were based on a pre-set list of codes, derived from a prior documentation study and a focus group with PCC experts.  Results: Perceived advantages of PCCs were more continuity of care, shorter communication lines, low-threshold contact between professionals and promising future perspectives. Perceived challenges included the absence of uniform multidisciplinary guidelines, delays in communication with hospitals and midwives, inappropriate accommodation for effective professional integration, differing expectations regarding the PCC-manager role among PCC-partners and the danger of professionals' needs dominating clients' needs. Conclusions: Professionals perceive PCCs as a promising development in the integration of services. Remaining challenges involved improvements at the managerial and organizational level. Quantitative research into the improvements in quality of care and child health is recommended.

  6. Multidisciplinary design and optimization (MDO) methodology for the aircraft conceptual design

    Science.gov (United States)

    Iqbal, Liaquat Ullah

    An integrated design and optimization methodology has been developed for the conceptual design of an aircraft. The methodology brings higher fidelity Computer Aided Design, Engineering and Manufacturing (CAD, CAE and CAM) Tools such as CATIA, FLUENT, ANSYS and SURFCAM into the conceptual design by utilizing Excel as the integrator and controller. The approach is demonstrated to integrate with many of the existing low to medium fidelity codes such as the aerodynamic panel code called CMARC and sizing and constraint analysis codes, thus providing the multi-fidelity capabilities to the aircraft designer. The higher fidelity design information from the CAD and CAE tools for the geometry, aerodynamics, structural and environmental performance is provided for the application of the structured design methods such as the Quality Function Deployment (QFD) and the Pugh's Method. The higher fidelity tools bring the quantitative aspects of a design such as precise measurements of weight, volume, surface areas, center of gravity (CG) location, lift over drag ratio, and structural weight, as well as the qualitative aspects such as external geometry definition, internal layout, and coloring scheme early in the design process. The performance and safety risks involved with the new technologies can be reduced by modeling and assessing their impact more accurately on the performance of the aircraft. The methodology also enables the design and evaluation of the novel concepts such as the blended (BWB) and the hybrid wing body (HWB) concepts. Higher fidelity computational fluid dynamics (CFD) and finite element analysis (FEA) allow verification of the claims for the performance gains in aerodynamics and ascertain risks of structural failure due to different pressure distribution in the fuselage as compared with the tube and wing design. The higher fidelity aerodynamics and structural models can lead to better cost estimates that help reduce the financial risks as well. This helps in

  7. Design Analysis Method for Multidisciplinary Complex Product using SysML

    Directory of Open Access Journals (Sweden)

    Liu Jihong

    2017-01-01

    Full Text Available In the design of multidisciplinary complex products, model-based systems engineering methods are widely used. However, the methodologies only contain only modeling order and simple analysis steps, and lack integrated design analysis methods supporting the whole process. In order to solve the problem, a conceptual design analysis method with integrating modern design methods has been proposed. First, based on the requirement analysis of the quantization matrix, the user’s needs are quantitatively evaluated and translated to system requirements. Then, by the function decomposition of the function knowledge base, the total function is semi-automatically decomposed into the predefined atomic function. The function is matched into predefined structure through the behaviour layer using function-structure mapping based on the interface matching. Finally based on design structure matrix (DSM, the structure reorganization is completed. The process of analysis is implemented with SysML, and illustrated through an aircraft air conditioning system for the system validation.

  8. Virtual reality as a multidisciplinary convergence tool in the product design process

    Directory of Open Access Journals (Sweden)

    Gaël Guerlesquin

    2012-02-01

    Full Text Available Nowadays firms have to use concurrent design to meet customers’ expectations. A plural approach to the design process is essential. Unfortunately, the design activity involves experts specialized in various aspects of the product such as aesthetics, ergonomics and mechanics. Thus the collaboration between these experts is particularly difficult in the convergence steps and often results in complex adjustments. This paper details a proposition of design methodology based on a multidisciplinary approach, using virtual reality tools. Our goal is to facilitate the integration of ergonomics and aesthetics in a mechanical design process. In this context, we consider virtual reality as an intermediary design tool useful for collaborative decision support during convergence phases. We present our methodology and associated tools tested during an industrial project, by focusing on an aesthetics-mechanics convergence step.

  9. Multi-disciplinary design optimization and performance evaluation of a single stage transonic axial compressor

    International Nuclear Information System (INIS)

    Lee, Sae Il; Lee, Dong Ho; Kim, Kyu Hong; Park, Tae Choon; Lim, Byeung Jun; Kang, Young Seok

    2013-01-01

    The multidisciplinary design optimization method, which integrates aerodynamic performance and structural stability, was utilized in the development of a single-stage transonic axial compressor. An approximation model was created using artificial neural network for global optimization within given ranges of variables and several design constraints. The genetic algorithm was used for the exploration of the Pareto front to find the maximum objective function value. The final design was chosen after a second stage gradient-based optimization process to improve the accuracy of the optimization. To validate the design procedure, numerical simulations and compressor tests were carried out to evaluate the aerodynamic performance and safety factor of the optimized compressor. Comparison between numerical optimal results and experimental data are well matched. The optimum shape of the compressor blade is obtained and compared to the baseline design. The proposed optimization framework improves the aerodynamic efficiency and the safety factor.

  10. Design and Analysis of an Airborne, solid Propelled, Nanosatellite Launch Vehicle using Multidisciplinary Design Optimization

    NARCIS (Netherlands)

    Van Kesteren, M.W.; Zandbergen, B.T.C.; Naeije, M.C.; Van Kleef, A.J.P.

    2015-01-01

    The work focusses on the use of multidisciplinary optimization to design a cost optimized airborne nanosatellite launch vehicle capable of bringing a 10 kg payload into low earth orbit (LEO). Piggyback or shared launch options currently available for nanosatellites are relatively low cost (~45,000

  11. How to Learn Multidisciplinary Design: Biomedical Engineering in Cross Cultural Seminar

    OpenAIRE

    Shigehiro Hashimoto

    2016-01-01

    The way to learn multidisciplinary design has been discussed. "Biomedical engineering" is exemplified for multidisciplinary field. "Biomedical Engineering" makes the multidisciplinary research area, which includes biology, medicine, engineering, and others. The cross-cultural student seminars on biomedical engineering have been exemplified as the case studies. In the group work, students are divided into the small cross cultural groups. Each group finds a problem, methods to solve the problem...

  12. Multidisciplinary Design, Analysis, and Optimization Tool Development Using a Genetic Algorithm

    Science.gov (United States)

    Pak, Chan-gi; Li, Wesley

    2009-01-01

    Multidisciplinary design, analysis, and optimization using a genetic algorithm is being developed at the National Aeronautics and Space Administration Dryden Flight Research Center (Edwards, California) to automate analysis and design process by leveraging existing tools to enable true multidisciplinary optimization in the preliminary design stage of subsonic, transonic, supersonic, and hypersonic aircraft. This is a promising technology, but faces many challenges in large-scale, real-world application. This report describes current approaches, recent results, and challenges for multidisciplinary design, analysis, and optimization as demonstrated by experience with the Ikhana fire pod design.!

  13. A Web-Based System for Monitoring and Controlling Multidisciplinary Design Projects

    Science.gov (United States)

    Salas, Andrea O.; Rogers, James L.

    1997-01-01

    In today's competitive environment, both industry and government agencies are under enormous pressure to reduce the time and cost of multidisciplinary design projects. A number of frameworks have been introduced to assist in this process by facilitating the integration of and communication among diverse disciplinary codes. An examination of current frameworks reveals weaknesses in various areas such as sequencing, displaying, monitoring, and controlling the design process. The objective of this research is to explore how Web technology, in conjunction with an existing framework, can improve these areas of weakness. This paper describes a system that executes a sequence of programs, monitors and controls the design process through a Web-based interface, and visualizes intermediate and final results through the use of Java(Tm) applets. A small sample problem, which includes nine processes with two analysis programs that are coupled to an optimizer, is used to demonstrate the feasibility of this approach.

  14. Multidisciplinary Design Techniques Applied to Conceptual Aerospace Vehicle Design. Ph.D. Thesis Final Technical Report

    Science.gov (United States)

    Olds, John Robert; Walberg, Gerald D.

    1993-01-01

    Multidisciplinary design optimization (MDO) is an emerging discipline within aerospace engineering. Its goal is to bring structure and efficiency to the complex design process associated with advanced aerospace launch vehicles. Aerospace vehicles generally require input from a variety of traditional aerospace disciplines - aerodynamics, structures, performance, etc. As such, traditional optimization methods cannot always be applied. Several multidisciplinary techniques and methods were proposed as potentially applicable to this class of design problem. Among the candidate options are calculus-based (or gradient-based) optimization schemes and parametric schemes based on design of experiments theory. A brief overview of several applicable multidisciplinary design optimization methods is included. Methods from the calculus-based class and the parametric class are reviewed, but the research application reported focuses on methods from the parametric class. A vehicle of current interest was chosen as a test application for this research. The rocket-based combined-cycle (RBCC) single-stage-to-orbit (SSTO) launch vehicle combines elements of rocket and airbreathing propulsion in an attempt to produce an attractive option for launching medium sized payloads into low earth orbit. The RBCC SSTO presents a particularly difficult problem for traditional one-variable-at-a-time optimization methods because of the lack of an adequate experience base and the highly coupled nature of the design variables. MDO, however, with it's structured approach to design, is well suited to this problem. The result of the application of Taguchi methods, central composite designs, and response surface methods to the design optimization of the RBCC SSTO are presented. Attention is given to the aspect of Taguchi methods that attempts to locate a 'robust' design - that is, a design that is least sensitive to uncontrollable influences on the design. Near-optimum minimum dry weight solutions are

  15. MOS integrated circuit design

    CERN Document Server

    Wolfendale, E

    2013-01-01

    MOS Integral Circuit Design aims to help in the design of integrated circuits, especially large-scale ones, using MOS Technology through teaching of techniques, practical applications, and examples. The book covers topics such as design equation and process parameters; MOS static and dynamic circuits; logic design techniques, system partitioning, and layout techniques. Also featured are computer aids such as logic simulation and mask layout, as well as examples on simple MOS design. The text is recommended for electrical engineers who would like to know how to use MOS for integral circuit desi

  16. Multidisciplinary Conceptual Design for Reduced-Emission Rotorcraft

    Science.gov (United States)

    Silva, Christopher; Johnson, Wayne; Solis, Eduardo

    2018-01-01

    Python-based wrappers for OpenMDAO are used to integrate disparate software for practical conceptual design of rotorcraft. The suite of tools which are connected thus far include aircraft sizing, comprehensive analysis, and parametric geometry. The tools are exercised to design aircraft with aggressive goals for emission reductions relative to fielded state-of-the-art rotorcraft. Several advanced reduced-emission rotorcraft are designed and analyzed, demonstrating the flexibility of the tools to consider a wide variety of potentially transformative vertical flight vehicles. To explore scale effects, aircraft have been sized for 5, 24, or 76 passengers in their design missions. Aircraft types evaluated include tiltrotor, single-main-rotor, coaxial, and side-by-side helicopters. Energy and drive systems modeled include Lithium-ion battery, hydrogen fuel cell, turboelectric hybrid, and turboshaft drive systems. Observations include the complex nature of the trade space for this simple problem, with many potential aircraft design and operational solutions for achieving significant emission reductions. Also interesting is that achieving greatly reduced emissions may not require exotic component technologies, but may be achieved with a dedicated design objective of reducing emissions.

  17. Application of analytical target cascading method in multidisciplinary design optimization of ship conceptual design

    Directory of Open Access Journals (Sweden)

    WANG Jian

    2017-10-01

    Full Text Available [Objectives] Ship conceptual design requires the coordination of many different disciplines for comprehensive optimization, which presents a complicated system design problem affecting several fields of technology. However, the development of overall ship design is relatively slow compared with other subjects. [Methods] The decomposition and coordination strategy of ship design is presented, and the analytical target cascading (ATC method is applied to the multidisciplinary design optimization of the conceptual design phase of ships on this basis. A tank ship example covering the 5 disciplines of buoyancy and stability, rapidity, maneuverability, capacity and economy is established to illustrate the analysis process in the present study. [Results] The results demonstrate the stability, convergence and validity of the ATC method in dealing with the complex coupling effect occurring in ship conceptual design.[Conclusions] The proposed method provides an effective basis for optimization of ship conceptual design.

  18. A surrogate based multistage-multilevel optimization procedure for multidisciplinary design optimization

    NARCIS (Netherlands)

    Yao, W.; Chen, X.; Ouyang, Q.; Van Tooren, M.

    2011-01-01

    Optimization procedure is one of the key techniques to address the computational and organizational complexities of multidisciplinary design optimization (MDO). Motivated by the idea of synthetically exploiting the advantage of multiple existing optimization procedures and meanwhile complying with

  19. A Web Centric Architecture for Deploying Multi-Disciplinary Engineering Design Processes

    Science.gov (United States)

    Woyak, Scott; Kim, Hongman; Mullins, James; Sobieszczanski-Sobieski, Jaroslaw

    2004-01-01

    There are continuous needs for engineering organizations to improve their design process. Current state of the art techniques use computational simulations to predict design performance, and optimize it through advanced design methods. These tools have been used mostly by individual engineers. This paper presents an architecture for achieving results at an organization level beyond individual level. The next set of gains in process improvement will come from improving the effective use of computers and software within a whole organization, not just for an individual. The architecture takes advantage of state of the art capabilities to produce a Web based system to carry engineering design into the future. To illustrate deployment of the architecture, a case study for implementing advanced multidisciplinary design optimization processes such as Bi-Level Integrated System Synthesis is discussed. Another example for rolling-out a design process for Design for Six Sigma is also described. Each example explains how an organization can effectively infuse engineering practice with new design methods and retain the knowledge over time.

  20. Multidisciplinary Modeling Software for Analysis, Design, and Optimization of HRRLS Vehicles

    Science.gov (United States)

    Spradley, Lawrence W.; Lohner, Rainald; Hunt, James L.

    2011-01-01

    The concept for Highly Reliable Reusable Launch Systems (HRRLS) under the NASA Hypersonics project is a two-stage-to-orbit, horizontal-take-off / horizontal-landing, (HTHL) architecture with an air-breathing first stage. The first stage vehicle is a slender body with an air-breathing propulsion system that is highly integrated with the airframe. The light weight slender body will deflect significantly during flight. This global deflection affects the flow over the vehicle and into the engine and thus the loads and moments on the vehicle. High-fidelity multi-disciplinary analyses that accounts for these fluid-structures-thermal interactions are required to accurately predict the vehicle loads and resultant response. These predictions of vehicle response to multi physics loads, calculated with fluid-structural-thermal interaction, are required in order to optimize the vehicle design over its full operating range. This contract with ResearchSouth addresses one of the primary objectives of the Vehicle Technology Integration (VTI) discipline: the development of high-fidelity multi-disciplinary analysis and optimization methods and tools for HRRLS vehicles. The primary goal of this effort is the development of an integrated software system that can be used for full-vehicle optimization. This goal was accomplished by: 1) integrating the master code, FEMAP, into the multidiscipline software network to direct the coupling to assure accurate fluid-structure-thermal interaction solutions; 2) loosely-coupling the Euler flow solver FEFLO to the available and proven aeroelasticity and large deformation (FEAP) code; 3) providing a coupled Euler-boundary layer capability for rapid viscous flow simulation; 4) developing and implementing improved Euler/RANS algorithms into the FEFLO CFD code to provide accurate shock capturing, skin friction, and heat-transfer predictions for HRRLS vehicles in hypersonic flow, 5) performing a Reynolds-averaged Navier-Stokes computation on an HRRLS

  1. Multidisciplinary teaching – Engineering course in advanced building design

    DEFF Research Database (Denmark)

    Dederichs, Anne; Karlshøj, Jan; Hertz, Kristian Dahl

    2011-01-01

    Collaboration within the building process is difficult. This calls for employees who are experienced in collaborating in interdisciplinary teams. To fulfil this demand a multidisciplinary course in “Advanced building design” has been developed at the Technical University of Denmark. The goal....... The students could experience that collaboration can be improved. The traditional role distribution can be broken and generally a flat team structure, where decisions are made in consensus, can be induced. The transprofessionalism during the course was appreciated but it was also described as a challenge...

  2. Rotorcraft Optimization Tools: Incorporating Rotorcraft Design Codes into Multi-Disciplinary Design, Analysis, and Optimization

    Science.gov (United States)

    Meyn, Larry A.

    2018-01-01

    One of the goals of NASA's Revolutionary Vertical Lift Technology Project (RVLT) is to provide validated tools for multidisciplinary design, analysis and optimization (MDAO) of vertical lift vehicles. As part of this effort, the software package, RotorCraft Optimization Tools (RCOTOOLS), is being developed to facilitate incorporating key rotorcraft conceptual design codes into optimizations using the OpenMDAO multi-disciplinary optimization framework written in Python. RCOTOOLS, also written in Python, currently supports the incorporation of the NASA Design and Analysis of RotorCraft (NDARC) vehicle sizing tool and the Comprehensive Analytical Model of Rotorcraft Aerodynamics and Dynamics II (CAMRAD II) analysis tool into OpenMDAO-driven optimizations. Both of these tools use detailed, file-based inputs and outputs, so RCOTOOLS provides software wrappers to update input files with new design variable values, execute these codes and then extract specific response variable values from the file outputs. These wrappers are designed to be flexible and easy to use. RCOTOOLS also provides several utilities to aid in optimization model development, including Graphical User Interface (GUI) tools for browsing input and output files in order to identify text strings that are used to identify specific variables as optimization input and response variables. This paper provides an overview of RCOTOOLS and its use

  3. Compressor and Turbine Multidisciplinary Design for Highly Efficient Micro-gas Turbine

    Science.gov (United States)

    Barsi, Dario; Perrone, Andrea; Qu, Yonglei; Ratto, Luca; Ricci, Gianluca; Sergeev, Vitaliy; Zunino, Pietro

    2018-06-01

    Multidisciplinary design optimization (MDO) is widely employed to enhance turbomachinery components efficiency. The aim of this work is to describe a complete tool for the aero-mechanical design of a radial inflow turbine and a centrifugal compressor. The high rotational speed of such machines and the high exhaust gas temperature (only for the turbine) expose blades to really high stresses and therefore the aerodynamics design has to be coupled with the mechanical one through an integrated procedure. The described approach employs a fully 3D Reynolds Averaged Navier-Stokes (RANS) solver for the aerodynamics and an open source Finite Element Analysis (FEA) solver for the mechanical integrity assessment. Due to the high computational cost of both these two solvers, a meta model, such as an artificial neural network (ANN), is used to speed up the optimization design process. The interaction between two codes, the mesh generation and the post processing of the results are achieved via in-house developed scripting modules. The obtained results are widely presented and discussed.

  4. Multidisciplinary design optimization of large wind turbines—Technical, economic, and design challenges

    International Nuclear Information System (INIS)

    Ashuri, Turaj; Zaaijer, Michiel B.; Martins, Joaquim R.R.A.; Zhang, Jie

    2016-01-01

    Highlights: • 5, 10 and 20 MW wind turbines are developed using multidisciplinary design optimization. • Technical feasibility and economy of large wind turbines are investigated. • Critical upscaling trends of existing wind turbines are presented up to 20 MW. • Design challenges of large wind turbines are identified, and design solutions proposed. • With no design innovation, upscaling of existing turbines will increase the costs. - Abstract: Wind energy has experienced a continuous cost reduction in the last decades. A popular cost reduction technique is to increase the rated power of the wind turbine by making it larger. However, it is not clear whether further upscaling of the existing wind turbines beyond the 5–7 MW range is technically feasible and economically attractive. To address this question, this study uses 5, 10, and 20 MW wind turbines that are developed using multidisciplinary design optimization as upscaling data points. These wind turbines are upwind, 3-bladed, pitch-regulated, variable-speed machines with a tubular tower. Based on the design data and properties of these wind turbines, scaling trends such as loading, mass, and cost are developed. These trends are used to study the technical and economical aspects of upscaling and its impact on the design and cost. The results of this research show the technical feasibility of the existing wind turbines up to 20 MW, but the design of such an upscaled machine is cost prohibitive. Mass increase of the rotor is identified as a main design challenge to overcome. The results of this research support the development of alternative lightweight materials and design concepts such as a two-bladed downwind design for upscaling to remain a cost effective solution for future wind turbines.

  5. Integrated design of MEMS

    DEFF Research Database (Denmark)

    De Grave, Arnaud; Brissaud, Daniel

    2007-01-01

    Emerging technologies of Micro-Electromechanical Systems (MEMS) are applications such as airbag accelerometers. Micro-products present many physical differences from macro-products. Moreover, there is a high level of integration in multiple fields of physics with strongly coupled effects...... industrial immersion to propose a socio-technological description of the design process and MEMS design tools....

  6. Recent experience with multidisciplinary analysis and optimization in advanced aircraft design

    Science.gov (United States)

    Dollyhigh, Samuel M.; Sobieszczanski-Sobieski, Jaroslaw

    1990-01-01

    narrowed as more sophisticated methods are developed in the specialist's area of expertise. The results have been a decrease in the awareness of the impact of his decisions on other disciplines. This paper will outline the progress and problems encountered in the analysis, design, optimization sensitivity analysis, mathematical modeling, and configurations control and the means by which they are being solved. The breadth versus depth dilemma in analysis and design and the means for coping with that dilemma will be discussed. Finally, the all-important human aspects and the need for a new 'culture ' for doing business in an integrated, multidisciplinary design environment are discussed.

  7. Framework for Multidisciplinary Analysis, Design, and Optimization with High-Fidelity Analysis Tools

    Science.gov (United States)

    Orr, Stanley A.; Narducci, Robert P.

    2009-01-01

    A plan is presented for the development of a high fidelity multidisciplinary optimization process for rotorcraft. The plan formulates individual disciplinary design problems, identifies practical high-fidelity tools and processes that can be incorporated in an automated optimization environment, and establishes statements of the multidisciplinary design problem including objectives, constraints, design variables, and cross-disciplinary dependencies. Five key disciplinary areas are selected in the development plan. These are rotor aerodynamics, rotor structures and dynamics, fuselage aerodynamics, fuselage structures, and propulsion / drive system. Flying qualities and noise are included as ancillary areas. Consistency across engineering disciplines is maintained with a central geometry engine that supports all multidisciplinary analysis. The multidisciplinary optimization process targets the preliminary design cycle where gross elements of the helicopter have been defined. These might include number of rotors and rotor configuration (tandem, coaxial, etc.). It is at this stage that sufficient configuration information is defined to perform high-fidelity analysis. At the same time there is enough design freedom to influence a design. The rotorcraft multidisciplinary optimization tool is built and substantiated throughout its development cycle in a staged approach by incorporating disciplines sequentially.

  8. Critical Issues Forum: A multidisciplinary educational program integrating computer technology

    Energy Technology Data Exchange (ETDEWEB)

    Alexander, R.J.; Robertson, B.; Jacobs, D. [Los Alamos National Lab., NM (United States)

    1998-09-01

    The Critical Issues Forum (CIF) funded by the US Department of Energy is a collaborative effort between the Science Education Team of Los Alamos National Laboratory (LANL) and New Mexico high schools to improve science education throughout the state of New Mexico as well as nationally. By creating an education relationship between the LANL with its unique scientific resources and New Mexico high schools, students and teachers participate in programs that increase not only their science content knowledge but also their critical thinking and problem-solving skills. The CIF program focuses on current, globally oriented topics crucial to the security of not only the US but to that of all nations. The CIF is an academic-year program that involves both teachers and students in the process of seeking solutions for real world concerns. Built around issues tied to LANL`s mission, participating students and teachers are asked to critically investigate and examine the interactions among the political, social, economic, and scientific domains while considering diversity issues that include geopolitical entities and cultural and ethnic groupings. Participants are expected to collaborate through telecommunications during the research phase and participate in a culminating multimedia activity, where they produce and deliver recommendations for the current issues being studied. The CIF was evaluated and found to be an effective approach for teacher professional training, especially in the development of skills for critical thinking and questioning. The CIF contributed to students` ability to integrate diverse disciplinary content about science-related topics and supported teachers in facilitating the understanding of their students using the CIF approach. Networking technology in CIF has been used as an information repository, resource delivery mechanism, and communication medium.

  9. Development of an Integrated Subspecialist Multidisciplinary Neuro-oncology Service

    Science.gov (United States)

    Price, Stephen J; Guilfoyle, Mathew; J Jefferies, Sarah; Harris, Fiona; Oberg, Ingela; G Burnet, Neil; Santarius, Thomas; Watts, Colin

    2013-01-01

    Traditionally, the poor outcome for patients with malignant brain tumours led to therapeutic nihilism. In turn, this resulted in lack of interest in neurosurgical oncology subspecialisation, and less than ideal patient pathways. One problem of concern was the low rate of tumour resection. Between 1997 and 2006, 685 treated glioblastomas were identified. In the first four years only 40% of patients underwent tumour resection, rising to 55% in the last four years. Before revision of the pathway, the median length of hospital stay was 8 days, and 35% of patients received the results of their histology outside of a clinic setting. A pathway of care was established, in which all patients were discussed pre-operatively in an MDT meeting and then directed into a new surgical neuro-oncology clinic providing first point of contact. This limited the number of surgeons operating on adult glioma patients and aided recruitment into research studies. Now, three consultant neurosurgeons run this service, easily fulfilling IOG requirement to spend >50% of programmed activities in neuro-oncology. Nursing support has been critical to provide an integrated service. This model has allowed increased recruitment to clinical trials. The introduction of this service led to an increase in patients discussed pre-operatively in an MDT (66% rising to 87%; P=0.027), an increase in the rate of surgical resection (from 40% to 80%) and more patients being admitted electively (from 25% to 80%; P<0.001). There was a reduction in the median length of stay (8 days reduced to 4.5 days; P<0.001). For the cohort of GBM patients that went on to have chemoradiotherapy we improved median survival to 18 months, with 35% of patients alive at two years, comparable to international outcomes. Implementing a specialist neurosurgical oncology service begins with understanding the patient care pathway. Our patients have benefitted from the culture of subspecialisation and the excellent inter-disciplinary working

  10. Multidisciplinary Design Optimization of a Swash-Plate Axial Piston Pump

    Directory of Open Access Journals (Sweden)

    Guangjun Liu

    2016-12-01

    Full Text Available This work proposes an MDO (multidisciplinary design optimization procedure for a swash-plate axial piston pump based on co-simulation and integrated optimization. The integrated hydraulic-mechanical model of the pump is built to reflect its actual performance, and a hydraulic-mechanical co-simulation is conducted through data exchange between different domains. The flow ripple of the pump is optimized by using a MDO procedure. A CFD (Computational Fluid Dynamics simulation of the pump’s flow field is done, which shows that the hydrodynamic shock of the pump is improved after optimization. To verify the MDO effect, an experimental system is established to test the optimized piston pump. Experimental results show that the simulated and experimental curves are similar. The flow ripple is improved by the MDO procedure. The peak of the pressure curve is lower than before optimization, and the pressure pulsation is reduced by 0.21 MPa, which shows that the pressure pulsation is improved with the decreasing of the flow ripple. Comparing the experimental and simulation results shows that MDO method is effective and feasible in the optimization design of the pump.

  11. Multi-Disciplinary Multi-Fidelity Design Environment, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — To meet the design challenges of tomorrow, NASA and industry require advancements in the state-of-the-art for physics-based design and analysis frameworks. In...

  12. Baseball Stadium Design: Teaching Engineering Economics and Technical Communication in a Multi-Disciplinary Setting.

    Science.gov (United States)

    Dahm, Kevin; Newell, James

    2001-01-01

    Reports on a course at Rowan University, based on the economic design of a baseball stadium, that offers an introduction to multidisciplinary engineering design linked with formal training in technical communication. Addresses four pedagogical goals: (1) developing public speaking skills in a realistic, business setting; (2) giving students…

  13. Construction management and economics: the epistemology of a multidisciplinary design science

    NARCIS (Netherlands)

    Voordijk, Johannes T.

    2009-01-01

    Research in the field of construction management and economics (CME) can be characterized as a multidisciplinary design science. Results from the sciences and humanities are necessary inputs for this field of research that deals with design, production and operation of the built environment. The

  14. Multi-Disciplinary Design Support using Hardware-in-the-Loop Simulation

    NARCIS (Netherlands)

    Visser, P.M.; Groothuis, M.A.; Broenink, Johannes F.

    2004-01-01

    This paper describes a method using Hardware-in-the-Loop Simulation as a means for multidisciplinary design support. The method presented here, aims at supporting the design of heterogeneous embedded control systems. The method considers the implementation process as a stepwise refinement from

  15. Development and Evaluation of an Undergraduate Multidisciplinary Project Activity in Engineering and Design

    Science.gov (United States)

    Smith, David R.; Cole, Joanne

    2012-01-01

    The School of Engineering and Design Multidisciplinary Project (MDP) at Brunel University is a one week long project based activity involving first year undergraduate students from across the School subject areas of Electronic and Computer Engineering, Mechanical Engineering, Civil Engineering and Design. This paper describes the main aims of the…

  16. Multidisciplinary Design Optimization Techniques: Implications and Opportunities for Fluid Dynamics Research

    Science.gov (United States)

    Zang, Thomas A.; Green, Lawrence L.

    1999-01-01

    A challenge for the fluid dynamics community is to adapt to and exploit the trend towards greater multidisciplinary focus in research and technology. The past decade has witnessed substantial growth in the research field of Multidisciplinary Design Optimization (MDO). MDO is a methodology for the design of complex engineering systems and subsystems that coherently exploits the synergism of mutually interacting phenomena. As evidenced by the papers, which appear in the biannual AIAA/USAF/NASA/ISSMO Symposia on Multidisciplinary Analysis and Optimization, the MDO technical community focuses on vehicle and system design issues. This paper provides an overview of the MDO technology field from a fluid dynamics perspective, giving emphasis to suggestions of specific applications of recent MDO technologies that can enhance fluid dynamics research itself across the spectrum, from basic flow physics to full configuration aerodynamics.

  17. Integrated, Multidisciplinary and Technology-Enhanced Science Education: The Next Frontier

    OpenAIRE

    Dinov, Ivo D.

    2008-01-01

    Contemporary science education at all levels presents several critical pedagogical and social challenges to educators and learners alike. Among these challenges are the widening Intergenerational Information Technology (IIT) divide and the need for a comprehensive and balanced multidisciplinary training. In the past few years, it has become clear that one significant hurdle impedes the efforts to integrate information technology in the classroom – the Intergenerational IT divide. The IIT gap ...

  18. An integrated methodology for process improvement and delivery system visualization at a multidisciplinary cancer center.

    Science.gov (United States)

    Singprasong, Rachanee; Eldabi, Tillal

    2013-01-01

    Multidisciplinary cancer centers require an integrated, collaborative, and stream-lined workflow in order to provide high quality of patient care. Due to the complex nature of cancer care and continuing changes to treatment techniques and technologies, it is a constant struggle for centers to obtain a systemic and holistic view of treatment workflow for improving the delivery systems. Project management techniques, Responsibility matrix and a swim-lane activity diagram representing sequence of activities can be combined for data collection, presentation, and evaluation of the patient care. This paper presents this integrated methodology using multidisciplinary meetings and walking the route approach for data collection, integrated responsibility matrix and swim-lane activity diagram with activity time for data representation and 5-why and gap analysis approach for data analysis. This enables collection of right detail of information in a shorter time frame by identifying process flaws and deficiencies while being independent of the nature of the patient's disease or treatment techniques. A case study of a multidisciplinary regional cancer centre is used to illustrate effectiveness of the proposed methodology and demonstrates that the methodology is simple to understand, allowing for minimal training of staff and rapid implementation. © 2011 National Association for Healthcare Quality.

  19. Human Pathogens on Plants: Designing a Multidisciplinary Strategy for Research.

    Science.gov (United States)

    Fletcher, Jacqueline; Leach, Jan E; Eversole, Kellye; Tauxe, Robert

    2014-10-15

    cross-over issues that pertain also to HPOP research, and can suggest logical strategies for minimizing the risk of microbial contamination. Continued interactions and communication among these two disciplinary communities is essential and can be achieved by the creation of an interdisciplinary research coordination network. We hope that this article, an introduction to the multidisciplinary HPOP arena, will be useful to researchers in many related fields.

  20. Human pathogens on plants: designing a multidisciplinary strategy for research.

    Science.gov (United States)

    Fletcher, Jacqueline; Leach, Jan E; Eversole, Kellye; Tauxe, Robert

    2013-04-01

    cross-over issues that pertain also to HPOP research, and can suggest logical strategies for minimizing the risk of microbial contamination. Continued interactions and communication among these two disciplinary communities is essential and can be achieved by the creation of an interdisciplinary research coordination network. We hope that this article, an introduction to the multidisciplinary HPOP arena, will be useful to researchers in many related fields.

  1. Multidisciplinary integration in the context of integrated care – results from the North West London Integrated Care Pilot

    Directory of Open Access Journals (Sweden)

    Matthew Harris

    2013-10-01

    Full Text Available Background: In the context of integrated care, Multidisciplinary Group (MDG meetings involve participants from diverse professional groups and organizations and are potential vehicles to advance efficiency improvements within the local health economy.  We advance a novel method to evaluate the effectiveness of MDGs by measuring the extent to which participants integrate within MDG meetings and whether this integration leads to improved working. Methods: We purposively selected four MDG meetings, and conducted a content analysis of audio-recorded and transcribed case discussions. Two coders independently coded utterances according to their ‘integrative intensity’ which was defined against three a priori independent domains – the Level (i.e. Individual, Collective and Systems; the Valence (Problem, Information and Solution; the Focus (Concrete and Abstract. Inter- and intra-rater reliability was tested with Kappa scores on one randomly selected Case Discussion.  Standardized weighted mean integration scores were calculated for Case Discussions across utterance deciles, indicating how integrative intensity changed during the conversations. Results: Twenty-three Case Discussions in four different MDG groups were transcribed and coded. Inter- and intra-rater reliability was good as shown by the Prevalence and Bias Adjusted Kappa Scores for one randomly selected Case Discussion.  There were differences in the proportion of utterances per participant type (Consultant 14.6%; Presenting GP 38.75%; Chair 7.8%; Non-Presenting GP 2.25%; Allied Health Professional 4.8%. Utterances were predominantly coded at low levels of integrative intensity; however there was a gradual increase (R2=0.66 in integrative intensity during the Case Discussions.  Based on analysis of the minutes and action points arising from the Case Discussions, this improved integration did not translate into actions moving forward. Interpretation: We characterize the MDGs as

  2. Development of multidisciplinary design optimization procedures for smart composite wings and turbomachinery blades

    Science.gov (United States)

    Jha, Ratneshwar

    Multidisciplinary design optimization (MDO) procedures have been developed for smart composite wings and turbomachinery blades. The analysis and optimization methods used are computationally efficient and sufficiently rigorous. Therefore, the developed MDO procedures are well suited for actual design applications. The optimization procedure for the conceptual design of composite aircraft wings with surface bonded piezoelectric actuators involves the coupling of structural mechanics, aeroelasticity, aerodynamics and controls. The load carrying member of the wing is represented as a single-celled composite box beam. Each wall of the box beam is analyzed as a composite laminate using a refined higher-order displacement field to account for the variations in transverse shear stresses through the thickness. Therefore, the model is applicable for the analysis of composite wings of arbitrary thickness. Detailed structural modeling issues associated with piezoelectric actuation of composite structures are considered. The governing equations of motion are solved using the finite element method to analyze practical wing geometries. Three-dimensional aerodynamic computations are performed using a panel code based on the constant-pressure lifting surface method to obtain steady and unsteady forces. The Laplace domain method of aeroelastic analysis produces root-loci of the system which gives an insight into the physical phenomena leading to flutter/divergence and can be efficiently integrated within an optimization procedure. The significance of the refined higher-order displacement field on the aeroelastic stability of composite wings has been established. The effect of composite ply orientations on flutter and divergence speeds has been studied. The Kreisselmeier-Steinhauser (K-S) function approach is used to efficiently integrate the objective functions and constraints into a single envelope function. The resulting unconstrained optimization problem is solved using the

  3. A Systematic Approach for Quantitative Analysis of Multidisciplinary Design Optimization Framework

    Science.gov (United States)

    Kim, Sangho; Park, Jungkeun; Lee, Jeong-Oog; Lee, Jae-Woo

    An efficient Multidisciplinary Design and Optimization (MDO) framework for an aerospace engineering system should use and integrate distributed resources such as various analysis codes, optimization codes, Computer Aided Design (CAD) tools, Data Base Management Systems (DBMS), etc. in a heterogeneous environment, and need to provide user-friendly graphical user interfaces. In this paper, we propose a systematic approach for determining a reference MDO framework and for evaluating MDO frameworks. The proposed approach incorporates two well-known methods, Analytic Hierarchy Process (AHP) and Quality Function Deployment (QFD), in order to provide a quantitative analysis of the qualitative criteria of MDO frameworks. Identification and hierarchy of the framework requirements and the corresponding solutions for the reference MDO frameworks, the general one and the aircraft oriented one were carefully investigated. The reference frameworks were also quantitatively identified using AHP and QFD. An assessment of three in-house frameworks was then performed. The results produced clear and useful guidelines for improvement of the in-house MDO frameworks and showed the feasibility of the proposed approach for evaluating an MDO framework without a human interference.

  4. Affordable Design: A Methodolgy to Implement Process-Based Manufacturing Cost into the Traditional Performance-Focused Multidisciplinary Design Optimization

    Science.gov (United States)

    Bao, Han P.; Samareh, J. A.

    2000-01-01

    The primary objective of this paper is to demonstrate the use of process-based manufacturing and assembly cost models in a traditional performance-focused multidisciplinary design and optimization process. The use of automated cost-performance analysis is an enabling technology that could bring realistic processbased manufacturing and assembly cost into multidisciplinary design and optimization. In this paper, we present a new methodology for incorporating process costing into a standard multidisciplinary design optimization process. Material, manufacturing processes, and assembly processes costs then could be used as the objective function for the optimization method. A case study involving forty-six different configurations of a simple wing is presented, indicating that a design based on performance criteria alone may not necessarily be the most affordable as far as manufacturing and assembly cost is concerned.

  5. Process Cost Modeling for Multi-Disciplinary Design Optimization

    Science.gov (United States)

    Bao, Han P.; Freeman, William (Technical Monitor)

    2002-01-01

    For early design concepts, the conventional approach to cost is normally some kind of parametric weight-based cost model. There is now ample evidence that this approach can be misleading and inaccurate. By the nature of its development, a parametric cost model requires historical data and is valid only if the new design is analogous to those for which the model was derived. Advanced aerospace vehicles have no historical production data and are nowhere near the vehicles of the past. Using an existing weight-based cost model would only lead to errors and distortions of the true production cost. This report outlines the development of a process-based cost model in which the physical elements of the vehicle are costed according to a first-order dynamics model. This theoretical cost model, first advocated by early work at MIT, has been expanded to cover the basic structures of an advanced aerospace vehicle. Elemental costs based on the geometry of the design can be summed up to provide an overall estimation of the total production cost for a design configuration. This capability to directly link any design configuration to realistic cost estimation is a key requirement for high payoff MDO problems. Another important consideration in this report is the handling of part or product complexity. Here the concept of cost modulus is introduced to take into account variability due to different materials, sizes, shapes, precision of fabrication, and equipment requirements. The most important implication of the development of the proposed process-based cost model is that different design configurations can now be quickly related to their cost estimates in a seamless calculation process easily implemented on any spreadsheet tool. In successive sections, the report addresses the issues of cost modeling as follows. First, an introduction is presented to provide the background for the research work. Next, a quick review of cost estimation techniques is made with the intention to

  6. Integrated Program of Multidisciplinary Education and Research in Mechanics and Physics of Earthquakes

    Science.gov (United States)

    Lapusta, N.

    2011-12-01

    Studying earthquake source processes is a multidisciplinary endeavor involving a number of subjects, from geophysics to engineering. As a solid mechanician interested in understanding earthquakes through physics-based computational modeling and comparison with observations, I need to educate and attract students from diverse areas. My CAREER award has provided the crucial support for the initiation of this effort. Applying for the award made me to go through careful initial planning in consultation with my colleagues and administration from two divisions, an important component of the eventual success of my path to tenure. Then, the long-term support directed at my program as a whole - and not a specific year-long task or subject area - allowed for the flexibility required for a start-up of a multidisciplinary undertaking. My research is directed towards formulating realistic fault models that incorporate state-of-the-art experimental studies, field observations, and analytical models. The goal is to compare the model response - in terms of long-term fault behavior that includes both sequences of simulated earthquakes and aseismic phenomena - with observations, to identify appropriate constitutive laws and parameter ranges. CAREER funding has enabled my group to develop a sophisticated 3D modeling approach that we have used to understand patterns of seismic and aseismic fault slip on the Sunda megathrust in Sumatra, investigate the effect of variable hydraulic properties on fault behavior, with application to Chi-Chi and Tohoku earthquake, create a model of the Parkfield segment of the San Andreas fault that reproduces both long-term and short-term features of the M6 earthquake sequence there, and design experiments with laboratory earthquakes, among several other studies. A critical ingredient in this research program has been the fully integrated educational component that allowed me, on the one hand, to expose students from different backgrounds to the

  7. Multidisciplinary design optimization of film-cooled gas turbine blades

    OpenAIRE

    Shashishekara S. Talya; J. N. Rajadas; A. Chattopadhyay

    1999-01-01

    Design optimization of a gas turbine blade geometry for effective film cooling toreduce the blade temperature has been done using a multiobjective optimization formulation. Three optimization formulations have been used. In the first, the average blade temperature is chosen as the objective function to be minimized. An upper bound constraint has been imposed on the maximum blade temperature. In the second, the maximum blade temperature is chosen as the objective function to be minimized with ...

  8. How I learned to appreciate our tame social scientist : experiences in integrating design research and the behavioural sciences

    NARCIS (Netherlands)

    Reint-Jan Renes; Sander Hermsen; Remko van der Lugt; Sander Mulder

    2016-01-01

    Designing solutions for complex behaviour change processes can be greatly aided by integrating insights from the behavioural sciences into design practice. However, this integration is hampered by the relative inaccessibility of behavioral scientific knowledge. Working in a multidisciplinary of

  9. Multidisciplinary design optimization of film-cooled gas turbine blades

    Directory of Open Access Journals (Sweden)

    Talya Shashishekara S.

    1999-01-01

    Full Text Available Design optimization of a gas turbine blade geometry for effective film cooling toreduce the blade temperature has been done using a multiobjective optimization formulation. Three optimization formulations have been used. In the first, the average blade temperature is chosen as the objective function to be minimized. An upper bound constraint has been imposed on the maximum blade temperature. In the second, the maximum blade temperature is chosen as the objective function to be minimized with an upper bound constraint on the average blade temperature. In the third formulation, the blade average and maximum temperatures are chosen as objective functions. Shape optimization is performed using geometric parameters associated with film cooling and blade external shape. A quasi-three-dimensional Navier–Stokes solver for turbomachinery flows is used to solve for the flow field external to the blade with appropriate modifications to incorporate the effect of film cooling. The heat transfer analysis for temperature distribution within the blade is performed by solving the heat diffusion equation using the finite element method. The multiobjective Kreisselmeier–Steinhauser function approach has been used in conjunction with an approximate analysis technique for optimization. The results obtained using both formulations are compared with reference geometry. All three formulations yield significant reductions in blade temperature with the multiobjective formulation yielding largest reduction in blade temperature.

  10. Multidisciplinary Design Optimisation (MDO) Methods: Their Synergy with Computer Technology in the Design Process

    Science.gov (United States)

    Sobieszczanski-Sobieski, Jaroslaw

    1999-01-01

    The paper identifies speed, agility, human interface, generation of sensitivity information, task decomposition, and data transmission (including storage) as important attributes for a computer environment to have in order to support engineering design effectively. It is argued that when examined in terms of these attributes the presently available environment can be shown to be inadequate. A radical improvement is needed, and it may be achieved by combining new methods that have recently emerged from multidisciplinary design optimisation (MDO) with massively parallel processing computer technology. The caveat is that, for successful use of that technology in engineering computing, new paradigms for computing will have to be developed - specifically, innovative algorithms that are intrinsically parallel so that their performance scales up linearly with the number of processors. It may be speculated that the idea of simulating a complex behaviour by interaction of a large number of very simple models may be an inspiration for the above algorithms; the cellular automata are an example. Because of the long lead time needed to develop and mature new paradigms, development should begin now, even though the widespread availability of massively parallel processing is still a few years away.

  11. Multidisciplinary Design Optimization (MDO) Methods: Their Synergy with Computer Technology in Design Process

    Science.gov (United States)

    Sobieszczanski-Sobieski, Jaroslaw

    1998-01-01

    The paper identifies speed, agility, human interface, generation of sensitivity information, task decomposition, and data transmission (including storage) as important attributes for a computer environment to have in order to support engineering design effectively. It is argued that when examined in terms of these attributes the presently available environment can be shown to be inadequate a radical improvement is needed, and it may be achieved by combining new methods that have recently emerged from multidisciplinary design optimization (MDO) with massively parallel processing computer technology. The caveat is that, for successful use of that technology in engineering computing, new paradigms for computing will have to be developed - specifically, innovative algorithms that are intrinsically parallel so that their performance scales up linearly with the number of processors. It may be speculated that the idea of simulating a complex behavior by interaction of a large number of very simple models may be an inspiration for the above algorithms, the cellular automata are an example. Because of the long lead time needed to develop and mature new paradigms, development should be now, even though the widespread availability of massively parallel processing is still a few years away.

  12. The multidisciplinary design optimization of a distributed propulsion blended-wing-body aircraft

    Science.gov (United States)

    Ko, Yan-Yee Andy

    The purpose of this study is to examine the multidisciplinary design optimization (MDO) of a distributed propulsion blended-wing-body (BWB) aircraft. The BWB is a hybrid shape resembling a flying wing, placing the payload in the inboard sections of the wing. The distributed propulsion concept involves replacing a small number of large engines with many smaller engines. The distributed propulsion concept considered here ducts part of the engine exhaust to exit out along the trailing edge of the wing. The distributed propulsion concept affects almost every aspect of the BWB design. Methods to model these effects and integrate them into an MDO framework were developed. The most important effect modeled is the impact on the propulsive efficiency. There has been conjecture that there will be an increase in propulsive efficiency when there is blowing out of the trailing edge of a wing. A mathematical formulation was derived to explain this. The formulation showed that the jet 'fills in' the wake behind the body, improving the overall aerodynamic/propulsion system, resulting in an increased propulsive efficiency. The distributed propulsion concept also replaces the conventional elevons with a vectored thrust system for longitudinal control. An extension of Spence's Jet Flap theory was developed to estimate the effects of this vectored thrust system on the aircraft longitudinal control. It was found to provide a reasonable estimate of the control capability of the aircraft. An MDO framework was developed, integrating all the distributed propulsion effects modeled. Using a gradient based optimization algorithm, the distributed propulsion BWB aircraft was optimized and compared with a similarly optimized conventional BWB design. Both designs are for an 800 passenger, 0.85 cruise Mach number and 7000 nmi mission. The MDO results found that the distributed propulsion BWB aircraft has a 4% takeoff gross weight and a 2% fuel weight. Both designs have similar planform shapes

  13. Multidisciplinary group performance – measuring integration intensity in the context of the North West London Integrated Care Pilot

    Directory of Open Access Journals (Sweden)

    Matthew Harris

    2013-02-01

    Full Text Available Introduction: Multidisciplinary Group meeting (MDGs are seen as key facilitators of integration, moving from individual to multi-disciplinary decision making, and from a focus on individual patients to a focus on patient groups.  We have developed a method for coding MDG transcripts to identify whether they are or are not vehicles for delivering the anticipated efficiency improvements across various providers and apply it to a test case in the North West London Integrated Care Pilot.  Methods:  We defined 'integrating' as the process within the MDG meeting that enables or promotes an improved collaboration, improved understanding, and improved awareness of self and others within the local healthcare economy such that efficiency improvements could be identified and action taken.  Utterances within the MDGs are coded according to three distinct domains grounded in concepts from communication, group decision-making, and integrated care literatures - the Valence, the Focus, and the Level.  Standardized weighted integrative intensity scores are calculated across ten time deciles in the Case Discussion providing a graphical representation of its integrative intensity. Results: Intra- and Inter-rater reliability of the coding scheme was very good as measured by the Prevalence and Bias-adjusted Kappa Score.  Standardized Weighted Integrative Intensity graph mirrored closely the verbatim transcript and is a convenient representation of complex communication dynamics. Trend in integrative intensity can be calculated and the characteristics of the MDG can be pragmatically described. Conclusion: This is a novel and potentially useful method for researchers, managers and practitioners to better understand MDG dynamics and to identify whether participants are integrating.  The degree to which participants use MDG meetings to develop an integrated way of working is likely to require management, leadership and shared values.

  14. Multidisciplinary group performance – measuring integration intensity in the context of the North West London Integrated Care Pilot

    Directory of Open Access Journals (Sweden)

    Matthew Harris

    2013-02-01

    Full Text Available Introduction: Multidisciplinary Group meeting (MDGs are seen as key facilitators of integration, moving from individual to multi-disciplinary decision making, and from a focus on individual patients to a focus on patient groups.  We have developed a method for coding MDG transcripts to identify whether they are or are not vehicles for delivering the anticipated efficiency improvements across various providers and apply it to a test case in the North West London Integrated Care Pilot. Methods:  We defined 'integrating' as the process within the MDG meeting that enables or promotes an improved collaboration, improved understanding, and improved awareness of self and others within the local healthcare economy such that efficiency improvements could be identified and action taken.  Utterances within the MDGs are coded according to three distinct domains grounded in concepts from communication, group decision-making, and integrated care literatures - the Valence, the Focus, and the Level.  Standardized weighted integrative intensity scores are calculated across ten time deciles in the Case Discussion providing a graphical representation of its integrative intensity.Results: Intra- and Inter-rater reliability of the coding scheme was very good as measured by the Prevalence and Bias-adjusted Kappa Score.  Standardized Weighted Integrative Intensity graph mirrored closely the verbatim transcript and is a convenient representation of complex communication dynamics. Trend in integrative intensity can be calculated and the characteristics of the MDG can be pragmatically described.Conclusion: This is a novel and potentially useful method for researchers, managers and practitioners to better understand MDG dynamics and to identify whether participants are integrating.  The degree to which participants use MDG meetings to develop an integrated way of working is likely to require management, leadership and shared values.

  15. GLobal Integrated Design Environment

    Science.gov (United States)

    Kunkel, Matthew; McGuire, Melissa; Smith, David A.; Gefert, Leon P.

    2011-01-01

    The GLobal Integrated Design Environment (GLIDE) is a collaborative engineering application built to resolve the design session issues of real-time passing of data between multiple discipline experts in a collaborative environment. Utilizing Web protocols and multiple programming languages, GLIDE allows engineers to use the applications to which they are accustomed in this case, Excel to send and receive datasets via the Internet to a database-driven Web server. Traditionally, a collaborative design session consists of one or more engineers representing each discipline meeting together in a single location. The discipline leads exchange parameters and iterate through their respective processes to converge on an acceptable dataset. In cases in which the engineers are unable to meet, their parameters are passed via e-mail, telephone, facsimile, or even postal mail. The result of this slow process of data exchange would elongate a design session to weeks or even months. While the iterative process remains in place, software can now exchange parameters securely and efficiently, while at the same time allowing for much more information about a design session to be made available. GLIDE is written in a compilation of several programming languages, including REALbasic, PHP, and Microsoft Visual Basic. GLIDE client installers are available to download for both Microsoft Windows and Macintosh systems. The GLIDE client software is compatible with Microsoft Excel 2000 or later on Windows systems, and with Microsoft Excel X or later on Macintosh systems. GLIDE follows the Client-Server paradigm, transferring encrypted and compressed data via standard Web protocols. Currently, the engineers use Excel as a front end to the GLIDE Client, as many of their custom tools run in Excel.

  16. Improving sustainability during hospital design and operation a multidisciplinary evaluation tool

    CERN Document Server

    Bottero, Marta; Buffoli, Maddalena; Lettieri, Emanuele

    2015-01-01

    This book describes the Sustainable High Quality Healthcare (SustHealth) project, which had the goal of developing an original multidisciplinary evaluation tool that can be applied to assess and improve hospitals’ overall sustainability. The comprehensive nature of the appraisal offered by this tool exceeds the scope of most current rating systems, which typically permit a thorough evaluation of relevant environmental factors when designing a new building but fail to consider social and economic impacts of the design phase or the performance of the hospital’s operational structure in these fields. The multidisciplinary evaluation system was developed, from its very inception through to its testing, by following a scientific experimental method in which a global perspective was constantly maintained, as opposed to a focus only on specific technical issues. Application of the SustHealth rating tool to a currently functioning hospital, or one under design, will identify weaknesses and guide users to potentia...

  17. Complex multidisciplinary systems decomposition for aerospace vehicle conceptual design and technology acquisition

    Science.gov (United States)

    Omoragbon, Amen

    Although, the Aerospace and Defense (A&D) industry is a significant contributor to the United States' economy, national prestige and national security, it experiences significant cost and schedule overruns. This problem is related to the differences between technology acquisition assessments and aerospace vehicle conceptual design. Acquisition assessments evaluate broad sets of alternatives with mostly qualitative techniques, while conceptual design tools evaluate narrow set of alternatives with multidisciplinary tools. In order for these two fields to communicate effectively, a common platform for both concerns is desired. This research is an original contribution to a three-part solution to this problem. It discusses the decomposition step of an innovation technology and sizing tool generation framework. It identifies complex multidisciplinary system definitions as a bridge between acquisition and conceptual design. It establishes complex multidisciplinary building blocks that can be used to build synthesis systems as well as technology portfolios. It also describes a Graphical User Interface Designed to aid in decomposition process. Finally, it demonstrates an application of the methodology to a relevant acquisition and conceptual design problem posed by the US Air Force.

  18. Efficient Multidisciplinary Analysis Approach for Conceptual Design of Aircraft with Large Shape Change

    Science.gov (United States)

    Chwalowski, Pawel; Samareh, Jamshid A.; Horta, Lucas G.; Piatak, David J.; McGowan, Anna-Maria R.

    2009-01-01

    The conceptual and preliminary design processes for aircraft with large shape changes are generally difficult and time-consuming, and the processes are often customized for a specific shape change concept to streamline the vehicle design effort. Accordingly, several existing reports show excellent results of assessing a particular shape change concept or perturbations of a concept. The goal of the current effort was to develop a multidisciplinary analysis tool and process that would enable an aircraft designer to assess several very different morphing concepts early in the design phase and yet obtain second-order performance results so that design decisions can be made with better confidence. The approach uses an efficient parametric model formulation that allows automatic model generation for systems undergoing radical shape changes as a function of aerodynamic parameters, geometry parameters, and shape change parameters. In contrast to other more self-contained approaches, the approach utilizes off-the-shelf analysis modules to reduce development time and to make it accessible to many users. Because the analysis is loosely coupled, discipline modules like a multibody code can be easily swapped for other modules with similar capabilities. One of the advantages of this loosely coupled system is the ability to use the medium- to high-fidelity tools early in the design stages when the information can significantly influence and improve overall vehicle design. Data transfer among the analysis modules are based on an accurate and automated general purpose data transfer tool. In general, setup time for the integrated system presented in this paper is 2-4 days for simple shape change concepts and 1-2 weeks for more mechanically complicated concepts. Some of the key elements briefly described in the paper include parametric model development, aerodynamic database generation, multibody analysis, and the required software modules as well as examples for a telescoping wing

  19. A New Multidisciplinary Design Optimization Method Accounting for Discrete and Continuous Variables under Aleatory and Epistemic Uncertainties

    Directory of Open Access Journals (Sweden)

    Hong-Zhong Huang

    2012-02-01

    Full Text Available Various uncertainties are inevitable in complex engineered systems and must be carefully treated in design activities. Reliability-Based Multidisciplinary Design Optimization (RBMDO has been receiving increasing attention in the past decades to facilitate designing fully coupled systems but also achieving a desired reliability considering uncertainty. In this paper, a new formulation of multidisciplinary design optimization, namely RFCDV (random/fuzzy/continuous/discrete variables Multidisciplinary Design Optimization (RFCDV-MDO, is developed within the framework of Sequential Optimization and Reliability Assessment (SORA to deal with multidisciplinary design problems in which both aleatory and epistemic uncertainties are present. In addition, a hybrid discrete-continuous algorithm is put forth to efficiently solve problems where both discrete and continuous design variables exist. The effectiveness and computational efficiency of the proposed method are demonstrated via a mathematical problem and a pressure vessel design problem.

  20. Selection of a turbine cooling system applying multi-disciplinary design considerations.

    Science.gov (United States)

    Glezer, B

    2001-05-01

    The presented paper describes a multi-disciplinary cooling selection approach applied to major gas turbine engine hot section components, including turbine nozzles, blades, discs, combustors and support structures, which maintain blade tip clearances. The paper demonstrates benefits of close interaction between participating disciplines starting from early phases of the hot section development. The approach targets advancements in engine performance and cost by optimizing the design process, often requiring compromises within individual disciplines.

  1. Creation of a Rapid High-Fidelity Aerodynamics Module for a Multidisciplinary Design Environment

    Science.gov (United States)

    Srinivasan, Muktha; Whittecar, William; Edwards, Stephen; Mavris, Dimitri N.

    2012-01-01

    surrogate model, which captures the relationships between input variables and responses into regression equations. Depending on the dimensionality of the problem and the fidelity of the code for which a surrogate model is being created, the initial DOE can itself be computationally prohibitive to run. Cokriging, a modeling approach from the field of geostatistics, provides a desirable compromise between computational expense and fidelity. To do this, cokriging leverages a large body of data generated by a low fidelity analysis, combines it with a smaller set of data from a higher fidelity analysis, and creates a kriging surrogate model with prediction fidelity approaching that of the higher fidelity analysis. When integrated into a multidisciplinary environment, a disciplinary analysis module employing cokriging can raise the analysis fidelity without drastically impacting the expense of design iterations. This is demonstrated through the creation of an aerodynamics analysis module in NASA s OpenMDAO framework. Aerodynamic analyses including Missile DATCOM, APAS, and USM3D are leveraged to create high fidelity aerodynamics decks for parametric vehicle geometries, which are created in NASA s Vehicle Sketch Pad (VSP). Several trade studies are performed to examine the achieved level of model fidelity, and the overall impact to vehicle design is quantified.

  2. Multidisciplinary design of a rocket-based combined cycle SSTO launch vehicle using Taguchi methods

    Science.gov (United States)

    Olds, John R.; Walberg, Gerald D.

    1993-01-01

    Results are presented from the optimization process of a winged-cone configuration SSTO launch vehicle that employs a rocket-based ejector/ramjet/scramjet/rocket operational mode variable-cycle engine. The Taguchi multidisciplinary parametric-design method was used to evaluate the effects of simultaneously changing a total of eight design variables, rather than changing them one at a time as in conventional tradeoff studies. A combination of design variables was in this way identified which yields very attractive vehicle dry and gross weights.

  3. Future integrated design environments

    DEFF Research Database (Denmark)

    Christiansson, Per; Svidt, Kjeld; Sørensen, Kristian Birch

    2009-01-01

    and modeling of explicit and implicit end-user needs and requirements on both the building to be designed and the supporting design tools. The paper provides grounds to higher success rate in capture of explicit and implicit end user needs and requirements on functional performance in use and re...

  4. Computational Design Tools for Integrated Design

    DEFF Research Database (Denmark)

    Holst, Malene Kirstine; Kirkegaard, Poul Henning

    2010-01-01

    In an architectural conceptual sketching process, where an architect is working with the initial ideas for a design, the process is characterized by three phases: sketching, evaluation and modification. Basically the architect needs to address three areas in the conceptual sketching phase......: aesthetical, functional and technical requirements. The aim of the present paper is to address the problem of a vague or not existing link between digital conceptual design tools used by architects and designers and engineering analysis and simulation tools. Based on an analysis of the architectural design...... process different digital design methods are related to tasks in an integrated design process....

  5. Morgellons disease: experiences of an integrated multidisciplinary dermatology team to achieve positive outcomes.

    Science.gov (United States)

    Mohandas, Padma; Bewley, Anthony; Taylor, Ruth

    2018-03-01

    In recent years, there has been a reported increase in affliction of the skin with small fibres or other particles. The condition has been referred to as Morgellons disease. Patients present with stinging, burning or crawling sensations of the skin, with perceived extrusion of inanimate material alongside fatigue and other systemic symptoms. Sufferers often experience significant morbidity and reduction in quality of life. We aimed to explore the various clinical presentations, management strategies and outcomes employed to treat this condition in our patients. We conducted a retrospective case notes review of 35 patients referred to our multidisciplinary psycho-dermatology clinic at the Royal London Hospital between January 2004 and January 2017. The majority of patients were women (25) 71.4%, with a mean age of 54.6 years (26-80 years). Most (26) 74.2% were living alone. The average duration of illness prior to presentation was 3.8 years (4 months-20 years). Many patients had perceived precipitating factors (54.2%) and often self-diagnosed (28.5%). Psychiatric co-morbidities included 42.8% with depressive symptoms and 25.7% with anxiety. Substance misuse was elicited in five patients (14%). Management of patients included both the treatment of skin disease and psychosocial co-morbidities. Out of the 35 patients who attended (14) 40% cleared or showed significant improvement. Sixteen (45.7%) patients were stable and under review. One patient declined treatment and three did not attend review. One patient died from disease unrelated to her skin condition. Morgellons disease is a condition, which is widely discussed on the internet and patients often self-diagnose. The course of the disease can be chronic and debilitating. For a positive outcome, it is important that a strong physican-patient relationship is cultivated. As demonstrated in this case series, managing patients holistically in an integrated multidisciplinary dermatology setting helps achieve

  6. Integration of Airfoil Design during the design of new blades

    Energy Technology Data Exchange (ETDEWEB)

    Sartori, L.; Bottasso, L.; Croce, A. [Politecnico di Milano, Milan (Italy); Grasso, F. [ECN Wind Power, Petten (Netherlands)

    2013-09-15

    Despite the fact that the design of a new blade is a multidisciplinary task, often the different disciplines are combined together at later stage. Looking at the aerodynamic design, it is common practice design/select the airfoils first and then design the blade in terms of chord and twist based on the initial selection of the airfoils. Although this approach is quite diffused, it limits the potentialities of obtaining optimal performance. The present work is focused on investigating the benefits of designing the external shape of the blade including the airfoil shapes together with chord and twist. To accomplish this, a design approach has been developed, where an advanced gradient based optimization algorithm is able to control the shape of the blade. The airfoils described in the work are the NACA 4 digits, while the chord distribution and the twist distribution are described through Bezier curves. In this way, the complexity of the problem is limited while a versatile geometrical description is kept. After the details of the optimization scheme are illustrated, several numerical examples are shown, demonstrating the advantages in terms of performance and development time of integrating the design of the airfoils during the optimization of the blade.

  7. Multidisciplinary design optimization of the diesel particulate filter in the composite regeneration process

    International Nuclear Information System (INIS)

    Zhang, Bin; E, Jiaqiang; Gong, Jinke; Yuan, Wenhua; Zuo, Wei; Li, Yu; Fu, Jun

    2016-01-01

    Highlights: • The multidisciplinary design optimization (MDO) for the DPF is presented. • MDO model and multi-objective functions of the DPF are established. • The optimal design parameters are obtained and DPF’s performances are improved. • The optimized results are verified by experiments. • The composite regeneration process of the optimized DPF allows a higher energy saving. - Abstract: In our previous works, the diesel particulate filter (DPF) using a new composite regeneration mode by coupling microwave and ceria-manganese base catalysts is verified as an effective way to reduce the particulate matter emission of the diesel engine. In order to improve the overall performance of this DPF, its multidisciplinary design optimization (MDO) model is established based on objective functions such as pressure drop, regeneration performance, microwave energy consumption, and thermal shock resistance. Then, the DPF is optimized by using MDO method based on adaptive mutative scale chaos optimization algorithm. The optimization results show that with the help of MDO, DPF’s pressure drop is decreased by 14.5%, regeneration efficiency is increased by 17.3%, microwave energy consumption is decreased by 17.6%, and thermal deformation is decreased by 25.3%. The optimization results are also verified by experiments, and the experimental results indicate that the optimized DPF has larger filtration efficiency, better emission performance and regeneration performance, smaller pressure drop, lower wall temperature and temperature gradient, and lower microwave energy consumption.

  8. Issues and Strategies for Establishing Work-Integrated Learning for Multidisciplinary Teams: A Focus on Degrees in Sustainability

    Science.gov (United States)

    Wilson, Robyn Fay

    2015-01-01

    This study was conducted to identify challenges and potential strategies to streamline work-integrated learning placements for multidisciplinary teams of students undertaking degrees in sustainability. Face-to-face interviews using a semi-structured questionnaire were conducted with 15 academics and senior university staff, from four universities…

  9. STARS: An Integrated, Multidisciplinary, Finite-Element, Structural, Fluids, Aeroelastic, and Aeroservoelastic Analysis Computer Program

    Science.gov (United States)

    Gupta, K. K.

    1997-01-01

    A multidisciplinary, finite element-based, highly graphics-oriented, linear and nonlinear analysis capability that includes such disciplines as structures, heat transfer, linear aerodynamics, computational fluid dynamics, and controls engineering has been achieved by integrating several new modules in the original STARS (STructural Analysis RoutineS) computer program. Each individual analysis module is general-purpose in nature and is effectively integrated to yield aeroelastic and aeroservoelastic solutions of complex engineering problems. Examples of advanced NASA Dryden Flight Research Center projects analyzed by the code in recent years include the X-29A, F-18 High Alpha Research Vehicle/Thrust Vectoring Control System, B-52/Pegasus Generic Hypersonics, National AeroSpace Plane (NASP), SR-71/Hypersonic Launch Vehicle, and High Speed Civil Transport (HSCT) projects. Extensive graphics capabilities exist for convenient model development and postprocessing of analysis results. The program is written in modular form in standard FORTRAN language to run on a variety of computers, such as the IBM RISC/6000, SGI, DEC, Cray, and personal computer; associated graphics codes use OpenGL and IBM/graPHIGS language for color depiction. This program is available from COSMIC, the NASA agency for distribution of computer programs.

  10. Integrated circuit design using design automation

    International Nuclear Information System (INIS)

    Gwyn, C.W.

    1976-09-01

    Although the use of computer aids to develop integrated circuits is relatively new at Sandia, the program has been very successful. The results have verified the utility of the in-house CAD design capability. Custom IC's have been developed in much shorter times than available through semiconductor device manufacturers. In addition, security problems were minimized and a saving was realized in circuit cost. The custom CMOS IC's were designed at less than half the cost of designing with conventional techniques. In addition to the computer aided design, the prototype fabrication and testing capability provided by the semiconductor development laboratory and microelectronics computer network allows the circuits to be fabricated and evaluated before the designs are transferred to the commercial semiconductor manufacturers for production. The Sandia design and prototype fabrication facilities provide the capability of complete custom integrated circuit development entirely within the ERDA laboratories

  11. Analog Integrated Circuit Design for Spike Time Dependent Encoder and Reservoir in Reservoir Computing Processors

    Science.gov (United States)

    2018-01-01

    HAS BEEN REVIEWED AND IS APPROVED FOR PUBLICATION IN ACCORDANCE WITH ASSIGNED DISTRIBUTION STATEMENT. FOR THE CHIEF ENGINEER : / S / / S...bridged high-performance computing, nanotechnology , and integrated circuits & systems. 15. SUBJECT TERMS neuromorphic computing, neuron design, spike...multidisciplinary effort encompassed high-performance computing, nanotechnology , integrated circuits, and integrated systems. The project’s architecture was

  12. The Component Packaging Problem: A Vehicle for the Development of Multidisciplinary Design and Analysis Methodologies

    Science.gov (United States)

    Fadel, Georges; Bridgewood, Michael; Figliola, Richard; Greenstein, Joel; Kostreva, Michael; Nowaczyk, Ronald; Stevenson, Steve

    1999-01-01

    This report summarizes academic research which has resulted in an increased appreciation for multidisciplinary efforts among our students, colleagues and administrators. It has also generated a number of research ideas that emerged from the interaction between disciplines. Overall, 17 undergraduate students and 16 graduate students benefited directly from the NASA grant: an additional 11 graduate students were impacted and participated without financial support from NASA. The work resulted in 16 theses (with 7 to be completed in the near future), 67 papers or reports mostly published in 8 journals and/or presented at various conferences (a total of 83 papers, presentations and reports published based on NASA inspired or supported work). In addition, the faculty and students presented related work at many meetings, and continuing work has been proposed to NSF, the Army, Industry and other state and federal institutions to continue efforts in the direction of multidisciplinary and recently multi-objective design and analysis. The specific problem addressed is component packing which was solved as a multi-objective problem using iterative genetic algorithms and decomposition. Further testing and refinement of the methodology developed is presently under investigation. Teaming issues research and classes resulted in the publication of a web site, (http://design.eng.clemson.edu/psych4991) which provides pointers and techniques to interested parties. Specific advantages of using iterative genetic algorithms, hurdles faced and resolved, and institutional difficulties associated with multi-discipline teaming are described in some detail.

  13. A multi-disciplinary approach for the integrated assessment of water alterations under climate change

    Science.gov (United States)

    Sperotto, Anna; Torresan, Silvia; Molina, Jose Luis; Pulido Velazquez, Manuel; Critto, Andrea; Marcomini, Antonio

    2017-04-01

    Understanding the co-evolution and interrelations between natural and human pressures on water systems is required to ensure a sustainable management of resources under uncertain climate change conditions. To pursue multi-disciplinary research is therefore necessary to consider the multiplicity of stressors affecting water resources, take into account alternative perspectives (i.e. social, economic and environmental objective and priorities) and deal with uncertainty which characterize climate change scenarios. However, approaches commonly adopted in water quality assessment are predominantly mono-disciplinary, single-stressors oriented and apply concepts and models specific of different academic disciplines (e.g. physics, hydrology, ecology, sociology, economy) which, in fact, seldom shed their conceptual blinders failing to provide truly integrated results. In this context, the paper discusses the benefits and limits of adopting a multi-disciplinary approach where different knowledge domains collaborate and quantitative and qualitative information, coming from multiple conceptual and model-based research, are integrated in a harmonic manner. Specifically, Bayesian Networks are used as meta-modelling tool for structuring and combining the probabilistic information available in existing hydrological models, climate change and land use projections, historical observations and expert opinion. The developed network allows to perform a stochastic multi-risk assessment considering the interlacing between climate (i.e. irregularities in water regime) and land use changes (i.e. agriculture, urbanization) and their cascading impacts on water quality parameters (i.e. nutrients loadings). Main objective of the model is the development of multi-risk scenarios to assess and communicate the probability of not meeting a "Good chemical water status" over future timeframe taking into account projected climatic and not climatic conditions. The outcomes are finally used to identify

  14. Integrated Safety in Design

    DEFF Research Database (Denmark)

    Schultz, Casper Siebken; Jørgensen, Kirsten

    2014-01-01

    An on-going research project investigates the inclusion of health and safety considerations in the design phase as a means to achieve a higher level of health and safety in the construction industry. Moreover, the approach is coupled to the overall quality efforts. Two architectural firms and two...... consulting engineering firms are project participants. The hypothesis is that health and safety problems in execution can be prevented through better planning in the early stages of the construction processes and that accidents are prevented by providing safety. In the first stage of the research project...... a theoretical framework is developed from a combination of existing literature on health and safety and a mapping of existing practices based on interviews in all four companies. The interviews revealed that the basic knowledge on OHS among architects and engineers is limited. Also currently designers typically...

  15. Integrated Building Design

    DEFF Research Database (Denmark)

    Heiselberg, Per

    In the first half of the 20th century, HVAC systems and artificial lighting were developed to meet indoor comfort needs. Before the introduction of mechanical systems, climate - not building style or appearance - was the major determinant of building form. Comfort was achieved through passive means...... and architectural features built into the design. However, with the advent of new technologies, architects were no longer constrained by the need to ensure that buildings had ample daylighting, remained airy and cool in the summer and warm in the winter. Since HVAC systems and artificial lighting could satisfy...

  16. OpenMDAO: Framework for Flexible Multidisciplinary Design, Analysis and Optimization Methods

    Science.gov (United States)

    Heath, Christopher M.; Gray, Justin S.

    2012-01-01

    The OpenMDAO project is underway at NASA to develop a framework which simplifies the implementation of state-of-the-art tools and methods for multidisciplinary design, analysis and optimization. Foremost, OpenMDAO has been designed to handle variable problem formulations, encourage reconfigurability, and promote model reuse. This work demonstrates the concept of iteration hierarchies in OpenMDAO to achieve a flexible environment for supporting advanced optimization methods which include adaptive sampling and surrogate modeling techniques. In this effort, two efficient global optimization methods were applied to solve a constrained, single-objective and constrained, multiobjective version of a joint aircraft/engine sizing problem. The aircraft model, NASA's nextgeneration advanced single-aisle civil transport, is being studied as part of the Subsonic Fixed Wing project to help meet simultaneous program goals for reduced fuel burn, emissions, and noise. This analysis serves as a realistic test problem to demonstrate the flexibility and reconfigurability offered by OpenMDAO.

  17. Integrating computer programs for engineering analysis and design

    Science.gov (United States)

    Wilhite, A. W.; Crisp, V. K.; Johnson, S. C.

    1983-01-01

    The design of a third-generation system for integrating computer programs for engineering and design has been developed for the Aerospace Vehicle Interactive Design (AVID) system. This system consists of an engineering data management system, program interface software, a user interface, and a geometry system. A relational information system (ARIS) was developed specifically for the computer-aided engineering system. It is used for a repository of design data that are communicated between analysis programs, for a dictionary that describes these design data, for a directory that describes the analysis programs, and for other system functions. A method is described for interfacing independent analysis programs into a loosely-coupled design system. This method emphasizes an interactive extension of analysis techniques and manipulation of design data. Also, integrity mechanisms exist to maintain database correctness for multidisciplinary design tasks by an individual or a team of specialists. Finally, a prototype user interface program has been developed to aid in system utilization.

  18. Integrated aerodynamic-structural design of a forward-swept transport wing

    Science.gov (United States)

    Haftka, Raphael T.; Grossman, Bernard; Kao, Pi-Jen; Polen, David M.; Sobieszczanski-Sobieski, Jaroslaw

    1989-01-01

    The introduction of composite materials is having a profound effect on aircraft design. Since these materials permit the designer to tailor material properties to improve structural, aerodynamic and acoustic performance, they require an integrated multidisciplinary design process. Futhermore, because of the complexity of the design process, numerical optimization methods are required. The utilization of integrated multidisciplinary design procedures for improving aircraft design is not currently feasible because of software coordination problems and the enormous computational burden. Even with the expected rapid growth of supercomputers and parallel architectures, these tasks will not be practical without the development of efficient methods for cross-disciplinary sensitivities and efficient optimization procedures. The present research is part of an on-going effort which is focused on the processes of simultaneous aerodynamic and structural wing design as a prototype for design integration. A sequence of integrated wing design procedures has been developed in order to investigate various aspects of the design process.

  19. Product Design Engineering--A Global Education Trend in Multidisciplinary Training for Creative Product Design

    Science.gov (United States)

    de Vere, Ian; Melles, Gavin; Kapoor, Ajay

    2010-01-01

    Product design is the convergence point for engineering and design thinking and practices. Until recently, product design has been taught either as a component of mechanical engineering or as a subject within design schools but increasingly there is global recognition of the need for greater synergies between industrial design and engineering…

  20. The reablement team’s voice: a qualitative study of how an integrated multidisciplinary team experiences participation in reablement

    Directory of Open Access Journals (Sweden)

    Hjelle KM

    2016-11-01

    Full Text Available Kari Margrete Hjelle,1,2 Olbjørg Skutle,2,3 Oddvar Førland,2,4 Herdis Alvsvåg4 1Department of Occupational Therapy, Physiotherapy and Radiography, Faculty of Health and Social Sciences, Bergen University College, Bergen, Norway; 2Centre for Care Research Western Norway, Bergen University College, Bergen, Norway; 3Department of Health and Social Educators, Faculty of Health and Social Sciences, Bergen University College, Bergen, Norway; 4VID Specialized University, Bergen, Norway Background: Reablement is an early and time-limited home-based rehabilitation intervention that emphasizes intensive, goal-oriented, and multidisciplinary assistance for people experiencing functional decline. Few empirical studies to date have examined the experiences of the integrated multidisciplinary teams involved in reablement. Accordingly, the aim of this study was to explore and describe how an integrated multidisciplinary team in Norway experienced participation in reablement.Methods: An integrated multidisciplinary team consisting of health care professionals with a bachelor’s degree (including a physiotherapist, a social educator, occupational therapists, and nurses and home-based care personnel without a bachelor’s degree (auxiliary nurses and nursing assistants participated in focus group discussions. Qualitative content analysis was used to analyze the resulting data.Results: Three main themes emerged from the participants’ experiences with participating in reablement, including “the older adult’s goals are crucial”, “a different way of thinking and acting – a shift in work culture”, and “a better framework for cooperation and application of professional expertise and judgment”. The integrated multidisciplinary team and the older adults collaborated and worked in the same direction to achieve the person’s valued goals. The team supported the older adults in performing activities themselves rather than completing tasks for them. To

  1. Multifidelity, Multidisciplinary Design Under Uncertainty with Non-Intrusive Polynomial Chaos

    Science.gov (United States)

    West, Thomas K., IV; Gumbert, Clyde

    2017-01-01

    The primary objective of this work is to develop an approach for multifidelity uncertainty quantification and to lay the framework for future design under uncertainty efforts. In this study, multifidelity is used to describe both the fidelity of the modeling of the physical systems, as well as the difference in the uncertainty in each of the models. For computational efficiency, a multifidelity surrogate modeling approach based on non-intrusive polynomial chaos using the point-collocation technique is developed for the treatment of both multifidelity modeling and multifidelity uncertainty modeling. Two stochastic model problems are used to demonstrate the developed methodologies: a transonic airfoil model and multidisciplinary aircraft analysis model. The results of both showed the multifidelity modeling approach was able to predict the output uncertainty predicted by the high-fidelity model as a significant reduction in computational cost.

  2. Implications of intelligent, integrated microsystems for product design and development

    International Nuclear Information System (INIS)

    MYERS, DAVID R.; MCWHORTER, PAUL J.

    2000-01-01

    Intelligent, integrated microsystems combine some or all of the functions of sensing, processing information, actuation, and communication within a single integrated package, and preferably upon a single silicon chip. As the elements of these highly integrated solutions interact strongly with each other, the microsystem can be neither designed nor fabricated piecemeal, in contrast to the more familiar assembled products. Driven by technological imperatives, microsystems will best be developed by multi-disciplinary teams, most likely within the flatter, less hierarchical organizations. Standardization of design and process tools around a single, dominant technology will expedite economically viable operation under a common production infrastructure. The production base for intelligent, integrated microsystems has elements in common with the mathematical theory of chaos. Similar to chaos theory, the development of microsystems technology will be strongly dependent on, and optimized to, the initial product requirements that will drive standardization--thereby further rewarding early entrants to integrated microsystem technology

  3. Designing eHealth that Matters via a Multidisciplinary Requirements Development Approach.

    Science.gov (United States)

    Van Velsen, Lex; Wentzel, Jobke; Van Gemert-Pijnen, Julia Ewc

    2013-06-24

    Requirements development is a crucial part of eHealth design. It entails all the activities devoted to requirements identification, the communication of requirements to other developers, and their evaluation. Currently, a requirements development approach geared towards the specifics of the eHealth domain is lacking. This is likely to result in a mismatch between the developed technology and end user characteristics, physical surroundings, and the organizational context of use. It also makes it hard to judge the quality of eHealth design, since it makes it difficult to gear evaluations of eHealth to the main goals it is supposed to serve. In order to facilitate the creation of eHealth that matters, we present a practical, multidisciplinary requirements development approach which is embedded in a holistic design approach for eHealth (the Center for eHealth Research roadmap) that incorporates both human-centered design and business modeling. Our requirements development approach consists of five phases. In the first, preparatory, phase the project team is composed and the overall goal(s) of the eHealth intervention are decided upon. Second, primary end users and other stakeholders are identified by means of audience segmentation techniques and our stakeholder identification method. Third, the designated context of use is mapped and end users are profiled by means of requirements elicitation methods (eg, interviews, focus groups, or observations). Fourth, stakeholder values and eHealth intervention requirements are distilled from data transcripts, which leads to phase five, in which requirements are communicated to other developers using a requirements notation template we developed specifically for the context of eHealth technologies. The end result of our requirements development approach for eHealth interventions is a design document which includes functional and non-functional requirements, a list of stakeholder values, and end user profiles in the form of

  4. Design Integration of Facilities Management

    DEFF Research Database (Denmark)

    Jensen, Per Anker

    2009-01-01

    One of the problems in the building industry is a limited degree of learning from experiences of use and operation of existing buildings. Development of professional facilities management (FM) can be seen as the missing link to bridge the gap between building operation and building design....... Strategies, methods and barriers for the transfer and integration of operational knowledge into the design process are discussed. Multiple strategies are needed to improve the integration of FM in design. Building clients must take on a leading role in defining and setting up requirements and procedures...... on literature studies and case studies from the Nordic countries in Europe, including research reflections on experiences from a main case study, where the author, before becoming a university researcher, was engaged in the client organization as deputy project director with responsibility for the integration...

  5. Integrating pulmonary rehabilitation into the multidisciplinary management of lung cancer: a review.

    Science.gov (United States)

    Rivas-Perez, Hiram; Nana-Sinkam, Patrick

    2015-04-01

    Lung cancer is the number one cause of cancer related deaths. It is increasingly recognized that a multidisciplinary approach to the diagnosis and management of patients with lung cancer represents the ideal model for health care delivery. Given the high incidence of comorbid lung disease in lung cancer patients, strategies targeted at improving or optimizing these conditions may improve outcomes. Pulmonary rehabilitation (PR) has proven to be a useful management strategy for patients with chronic lung diseases including chronic obstructive pulmonary disease, interstitial lung disease and pulmonary hypertension. PR improves both exercise capacity and dyspnea. The effects of PR have also been studied in patients with lung cancer prior to and following surgical resection. Investigators have demonstrated significant improvements in six minute walk distance and lower extremity strength. In addition, patient recovery time is shorter when inpatient pulmonary rehabilitation is integrated prior to or following surgery. There are also positive reports regarding the benefits of exercise training in lung cancer patients receiving definite chemotherapy and radiotherapy. Pilot studies have demonstrated improvement in dyspnea scores as well as exercise capacity objectively measured by six minute walk distance. PR also offers an educational component in which patients have the opportunity to be educated regarding management of their disease as well as discuss goals of care. PR can be included as the standard of care for patients with advanced lung cancer with the goal of optimizing quality of life. Here, we provide a review of the current knowledge regarding PR in the management of patients with lung cancer. Published by Elsevier Ltd.

  6. Integration of design and inspection

    Science.gov (United States)

    Simmonds, William H.

    1990-08-01

    Developments in advanced computer integrated manufacturing technology, coupled with the emphasis on Total Quality Management, are exposing needs for new techniques to integrate all functions from design through to support of the delivered product. One critical functional area that must be integrated into design is that embracing the measurement, inspection and test activities necessary for validation of the delivered product. This area is being tackled by a collaborative project supported by the UK Government Department of Trade and Industry. The project is aimed at developing techniques for analysing validation needs and for planning validation methods. Within the project an experimental Computer Aided Validation Expert system (CAVE) is being constructed. This operates with a generalised model of the validation process and helps with all design stages: specification of product requirements; analysis of the assurance provided by a proposed design and method of manufacture; development of the inspection and test strategy; and analysis of feedback data. The kernel of the system is a knowledge base containing knowledge of the manufacturing process capabilities and of the available inspection and test facilities. The CAVE system is being integrated into a real life advanced computer integrated manufacturing facility for demonstration and evaluation.

  7. Product design engineering - a global education trend in multidisciplinary training for creative product design

    Science.gov (United States)

    de Vere, Ian; Melles, Gavin; Kapoor, Ajay

    2010-03-01

    Product design is the convergence point for engineering and design thinking and practices. Until recently, product design has been taught either as a component of mechanical engineering or as a subject within design schools but increasingly there is global recognition of the need for greater synergies between industrial design and engineering training. Product design engineering (PDE) is a new interdisciplinary programme combining the strengths of the industrial design and engineering. This paper examines the emergence of PDE in an environment of critique of conventional engineering education and exemplifies the current spread of programmes endorsing a hybrid programme of design and engineering skills. The paper exemplifies PDE with the analysis of the programme offered at Swinburne University of Technology (Australia), showing how the teaching of 'designerly' thinking to engineers produces a new graduate particularly suited to the current and future environment of produce design practice. The paper concludes with reflections on the significance of this innovative curriculum model for the field of product design and for engineering design in general.

  8. SPHERE's 'Dress Sense' a Multi-disciplinary approach to designing wearable technology to improve health

    Directory of Open Access Journals (Sweden)

    Amelia Martin

    2015-10-01

    Full Text Available Background Healthcare systems face financial challenges, with a greater number of the population living longer with long term conditions. In order to deliver safe, high quality care within these constraints, we must place more emphasis on preventing illness than treating illness. We can use the science of behaviour change, health, and technology to create solutions to these problems. An example of innovation in this field include SPHERE’s multidisciplinary project entitled ‘Dress Sense’, with the aim to create a piece of wearable technology to improve health. Description This competition was run by SPHERE (Sensor Platform for HEalthcare in a Residential Environment which focuses on developing sensor systems to monitor health and wellbeing in the home. The teams comprised of computer scientists, medical professionals, students and school children, engineers, fashion designers and textile artists. They were provided with a kit including Arduino software, sensors and other items to make wearable computers. There were no constraints on what they could produce, except for a deadline of 3 weeks. The end project was judged according to the innovation and usefulness of the overall concept; the functionality, usability and desirability (aesthetics of the constructed device and the multi-displinary component. The idea was to foster open innovation in order to share ideas between specialities. Conclusions Ideas included tackling diabetic medical adherence through a wearable band to sensors woven into socks to prevent deep vein thrombosis. The winning concept was, ‘Yo’ a support system to aid cognitive behaviour therapy, through wearable products and accessories, to help those who begin CBT, stay motivated to engage effectively with therapy. This project highlighs how through multi-disciplinary collaboration and including the younger generation, innovative effective ideas can be found to harness digital technology to improve health.

  9. The Integrated Design Process (IDP)

    DEFF Research Database (Denmark)

    Hansen, Hanne Tine Ring; Knudstrup, Mary-Ann

    2005-01-01

    the different parameters and products can interact, and which consequences this would have on a project. The IDP does not ensure aesthetic or sustainable solutions, but it enables the designer to control the many parameters that must be considered and integrated in the project when creating more holistic...

  10. Man-machine design integration

    Energy Technology Data Exchange (ETDEWEB)

    Carrera, J.P. [Westinghouse Electric Corp., Monroeville, PA (United States). Nuclear Technology Div.; Haentjens, J. [Westinghouse Electric Corp., Brussels (Belgium). Nuclear Technology Div.

    1995-12-31

    The presentation overviews the bases for Man-Machine Interface (MMI) designs that are part of three other presentations during the same conference: Advanced Alarm Management System, Functional Displays and System for Emergency Procedure Execution Monitoring. The MMD group history, team and goals are summarized to give some context to the core of the MMD philosophy and integration. (10 refs., 5 figs.).

  11. Toolbox for super-structured and super-structure free multi-disciplinary building spatial design optimisation

    NARCIS (Netherlands)

    Boonstra, S.; van der Blom, K.; Hofmeyer, H.; Emmerich, M.T.M.; van Schijndel, A.W.M.; de Wilde, P.

    2018-01-01

    Multi-disciplinary optimisation of building spatial designs is characterised by large solution spaces. Here two approaches are introduced, one being super-structured and the other super-structure free. Both are different in nature and perform differently for large solution spaces and each requires

  12. Human Integration Design Processes (HIDP)

    Science.gov (United States)

    Boyer, Jennifer

    2014-01-01

    The purpose of the Human Integration Design Processes (HIDP) document is to provide human-systems integration design processes, including methodologies and best practices that NASA has used to meet human systems and human rating requirements for developing crewed spacecraft. HIDP content is framed around human-centered design methodologies and processes in support of human-system integration requirements and human rating. NASA-STD-3001, Space Flight Human-System Standard, is a two-volume set of National Aeronautics and Space Administration (NASA) Agency-level standards established by the Office of the Chief Health and Medical Officer, directed at minimizing health and performance risks for flight crews in human space flight programs. Volume 1 of NASA-STD-3001, Crew Health, sets standards for fitness for duty, space flight permissible exposure limits, permissible outcome limits, levels of medical care, medical diagnosis, intervention, treatment and care, and countermeasures. Volume 2 of NASASTD- 3001, Human Factors, Habitability, and Environmental Health, focuses on human physical and cognitive capabilities and limitations and defines standards for spacecraft (including orbiters, habitats, and suits), internal environments, facilities, payloads, and related equipment, hardware, and software with which the crew interfaces during space operations. The NASA Procedural Requirements (NPR) 8705.2B, Human-Rating Requirements for Space Systems, specifies the Agency's human-rating processes, procedures, and requirements. The HIDP was written to share NASA's knowledge of processes directed toward achieving human certification of a spacecraft through implementation of human-systems integration requirements. Although the HIDP speaks directly to implementation of NASA-STD-3001 and NPR 8705.2B requirements, the human-centered design, evaluation, and design processes described in this document can be applied to any set of human-systems requirements and are independent of reference

  13. Utilizing Uncertainty Multidisciplinary Design Optimization for Conceptual Design of Space Systems

    NARCIS (Netherlands)

    Yao, W.; Guo, J.; Chen, X.; Van Tooren, M.

    2010-01-01

    With progress of space technology and increase of space mission demand, requirements for robustness and reliability of space systems are ever-increasing. For the whole space mission life cycle, the most important decisions are made in the conceptual design phase, so it is very crucial to take

  14. Implementing Universal Design Strategies in Municipalities - A Multidisciplinary Approach to Universal Design and Public Health.

    Science.gov (United States)

    Jensen, Roger

    2016-01-01

    Based on a national program, the regional authorities stimulated each of the 18 municipalities in Telemark 2012-15 to plan and build promenades with universal design. The cooperation between different disciplines was an important factor for good results. The project continues from 2016.

  15. Radiological controls integrated into design

    Energy Technology Data Exchange (ETDEWEB)

    Kindred, G.W. [Cleveland Electric Illuminating Co., Perry, OH (United States)

    1995-03-01

    Radiological controls are required by law in the design of commercial nuclear power reactor facilities. These controls can be relatively minor or significant, relative to cost. To ensure that radiological controls are designed into a project, the health physicist (radiological engineer) must be involved from the beginning. This is especially true regarding keeping costs down. For every radiological engineer at a nuclear power plant there must be fifty engineers of other disciplines. The radiological engineer cannot be an expert on every discipline of engineering. However, he must be knowledgeable to the degree of how a design will impact the facility from a radiological perspective. This paper will address how to effectively perform radiological analyses with the goal of radiological controls integrated into the design package.

  16. Status of integrated multidisciplinary rotorcraft optimization research at the Langley Research Center

    Science.gov (United States)

    Mantay, Wayne R.; Adelman, Howard M.

    1990-01-01

    This paper describes a joint NASA/Army research activity at the Langley Research Center to develop optimization procedures aimed at improving the rotor blade design process by integrating appropriate disciplines and accounting for important interactions among the disciplines. The activity is being guided by a Steering Committee made up of key NASA and Army researchers and managers. The paper describes the optimization formulation in terms of the objective function, design variables, and constraints. The analysis aspects are discussed, and the interdisciplinary interactions are defined in terms of the information that must be transferred among disciplinary analyses as well as the trade-offs between disciplines in determining the details of the design. At this writing, some significant progress has been made. Results given in the paper represent accomplishments in rotor aerodynamic performance optimization for minimum horsepower, rotor dynamic optimization for vibration reduction, approximate analysis of frequencies and mode shapes, rotor structural optimization for minimum weight, and integrated aerodynamic load/dynamics optimization for minimum vibration and weight.

  17. Integrated project delivery : The designer as integrator

    NARCIS (Netherlands)

    Wamelink, J.W.F.; Koolwijk, J.S.J.; van Doorn, A.J.

    2012-01-01

    Process innovation related to integrated project delivery is an important topic in the building industry. Studies on process innovation through the use of integrated contracts usually focus on contractors, and particularly on the possibility of forward integration into the building process. Three

  18. Aircraft System Design and Integration

    Directory of Open Access Journals (Sweden)

    D. P. Coldbeck

    2000-01-01

    Full Text Available In the 1980's the British aircraft industry changed its approach to the management of projects from a system where a project office would manage a project and rely on a series of specialist departments to support them to a more process oriented method, using systems engineering models, whose most outwardly visible signs were the introduction of multidisciplinary product teams. One of the problems with the old method was that the individual departments often had different priorities and projects would get uneven support. The change in the system was only made possible for complex designs by the electronic distribution of data giving instantaneous access to all involved in the project. In 1997 the Defence and Aerospace Foresight Panel emphasised the need for a system engineering approach if British industry was to remain competitive. The Royal Academy of Engineering recognised that the change in working practices also changed what was required of a chartered engineer and redefined their requirements in 1997 [1]. The result of this is that engineering degree courses are now judged against new criteria with more emphasis placed on the relevance to industry rather than on purely academic content. At the University of Glasgow it was realized that the students ought to be made aware of current working practices and that there ought to be a review to ensure that the degrees give students the skills required by industry. It was decided to produce a one week introduction course in systems engineering for Masters of Engineering (MEng students to be taught by both university lecturers and practitioners from a range of companies in the aerospace industry with the hope of expanding the course into a module. The reaction of the students was favourable in terms of the content but it seems ironic that the main criticism was that there was not enough discussion involving the students. This paper briefly describes the individual teaching modules and discusses the

  19. Concurrent multidisciplinary mechanical design based on design task analysis and knowledge sharing; Sekkei task bunseki to joho kyoyu ni yoru mechatronics kyocho sekkei

    Energy Technology Data Exchange (ETDEWEB)

    Kondo, K.; Ozawa, M.; Mori, T. [Toshiba Corp., Tokyo (Japan)

    1999-09-01

    We have developed a systematic design task planning method based on a design structure matrix(DSM) and a lumped model- based framework for knowledge sharing in a concurrent design environment as key techniques for developing higher quality products in a shorter design time. The DSM facilitates systematic analysis of dependencies among design tasks and optimization of the design process. The framework based on a lumped model description of mechanical systems enables concurrent and cooperative work among multidisciplinary designers at an early stage of the design process. In this paper, we also discuss the relationships between these techniques and the product development flow from product definition to detailed design. (author)

  20. Development of Integrative STEM Curriculum: A Multiple Case Study of Multi-Disciplinary Teams in Two Pennsylvania High Schools

    Science.gov (United States)

    Rider-Bertrand, Joey H.

    At the start of the 21st century, STEM education was a new priority in many schools as the focus shifted from separate disciplines to integrative STEM education. Unfortunately, there was limited research to offer guidance to practitioners (Brown, 2012; Honey, Pearson & Schweingruber, 2014). This qualitative, multiple case study explored the experiences of two multi-disciplinary teams of secondary teachers from Pennsylvania who developed and implemented integrative STEM curriculum. Four teachers from a rural high school and four teachers from a suburban high school participated in the study. A document review of integrative STEM curriculum and semi-structured interviews were conducted to learn about the curriculum development process and teachers' perceptions regarding conditions that support or hinder success. Individual and cross-case analyses were performed to establish findings and themes. Although the individual case themes varied slightly, the cross-case themes and assertions that emerged provided highly sought after guidance to practitioners and added to the limited body of research on integrative STEM education. This study found that current curriculum models do not fit integrative STEM curriculum, the development process is fluid, and substantial administrative support and resources are necessary to develop, implement, and sustain integrative STEM education programs. The results offered implications for all educators, as well as two examples of how teachers navigated the terrain of integrative STEM curriculum.

  1. Stochastic integer programming for multi-disciplinary outpatient clinic planning

    NARCIS (Netherlands)

    Leeftink, A. G.; Vliegen, I. M.H.; Hans, E. W.

    2017-01-01

    Scheduling appointments in a multi-disciplinary clinic is complex, since coordination between disciplines is required. The design of a blueprint schedule for a multi-disciplinary clinic with open access requirements requires an integrated optimization approach, in which all appointment schedules are

  2. A General Multidisciplinary Turbomachinery Design Optimization system Applied to a Transonic Fan

    Science.gov (United States)

    Nemnem, Ahmed Mohamed Farid

    The blade geometry design process is integral to the development and advancement of compressors and turbines in gas generators or aeroengines. A new airfoil section design capability has been added to an open source parametric 3D blade design tool. Curvature of the meanline is controlled using B-splines to create the airfoils. The curvature is analytically integrated to derive the angles and the meanline is obtained by integrating the angles. A smooth thickness distribution is then added to the airfoil to guarantee a smooth shape while maintaining a prescribed thickness distribution. A leading edge B-spline definition has also been implemented to achieve customized airfoil leading edges which guarantees smoothness with parametric eccentricity and droop. An automated turbomachinery design and optimization system has been created. An existing splittered transonic fan is used as a test and reference case. This design was more general than a conventional design to have access to the other design methodology. The whole mechanical and aerodynamic design loops are automated for the optimization process. The flow path and the geometrical properties of the rotor are initially created using the axi-symmetric design and analysis code (T-AXI). The main and splitter blades are parametrically designed with the created geometry builder (3DBGB) using the new added features (curvature technique). The solid model creation of the rotor sector with a periodic boundaries combining the main blade and splitter is done using MATLAB code directly connected to SolidWorks including the hub, fillets and tip clearance. A mechanical optimization is performed with DAKOTA (developed by DOE) to reduce the mass of the blades while keeping maximum stress as a constraint with a safety factor. A Genetic algorithm followed by Numerical Gradient optimization strategies are used in the mechanical optimization. The splittered transonic fan blades mass is reduced by 2.6% while constraining the maximum

  3. Designing Critique for Knowledge Integration

    Science.gov (United States)

    Sato, Mie Elissa

    Generating explanations is central to science and has the potential to have a powerful impact on students' conceptual understanding in science instruction. However, improving conceptual understanding by generating explanations is a fraught affair: students may struggle with the sense of false clarity that may arise from generating explanations, fail to detect gaps in their understanding, and dismiss salient information that contradict their beliefs. Critiquing explanations has the potential to counteract these pitfalls by exposing students to alternative ideas to contrast with their own. This dissertation seeks to clarify how to design critique in technology-enhanced science instruction to support students in revising their explanations about scientific phenomena, and in doing so, refining their conceptual understanding. Using the Knowledge Integration framework, I revised two technology-enhanced curriculum units, Plate Tectonics and Global Climate Change, in a design partnership between teachers, researchers, and technologists. I conducted a series of studies with sixth-grade students to investigate the conditions under which guided critique of explanations can support revision. The pilot critique study investigated the impact of the revised Plate Tectonics unit on students' understanding of convection, as well as of a preliminary design of critique where students generated and applied their own criteria for what makes a good explanation in science. The guidance study explored how incorporating a complex selection task that features meta-explanatory criteria into critique supports students in distinguishing among different criteria, as well as how students use peer or expert guidance on their initial explanation during revision. The critique study investigated how designing critique with a complex selection task that features plausible alternative ideas and giving guidance on students' critiques support students in distinguishing among a range of relevant ideas

  4. The Role of Guidance, Navigation, and Control in Hypersonic Vehicle Multidisciplinary Design and Optimization

    Science.gov (United States)

    Ouzts, Peter J.; Soloway, Donald I.; Moerder, Daniel D.; Wolpert, David H.; Benavides, Jose Victor

    2009-01-01

    Airbreathing hypersonic systems offer distinct performance advantages over rocket-based systems for space access vehicles. However, these performance advantages are dependent upon advances in current state-of-the-art technologies in many areas such as ram/scramjet propulsion integration, high temperature materials, aero-elastic structures, thermal protection systems, transition to hypersonics and hypersonic control elements within the framework of complex physics and new design methods. The complex interactions between elements of an airbreathing hypersonic vehicle represent a new paradigm in vehicle design to achieve the optimal performance necessary to meet space access mission objectives. In the past, guidance, navigation, and control (GNC) analysis often follows completion of the vehicle conceptual design process. Individual component groups design subsystems which are then integrated into a vehicle configuration. GNC is presented the task of developing control approaches to meet vehicle performance objectives given that configuration. This approach may be sufficient for vehicles where significant performance margins exist. However, for higher performance vehicles engaging the GNC discipline too late in the design cycle has been costly. For example, the X-29 experimental flight vehicle was built as a technology demonstrator. One of the many technologies to be demonstrated was the use of light-weight material composites for structural components. The use of light-weight materials increased the flexibility of the X- 29 beyond that of conventional metal alloy constructed aircraft. This effect was not considered when the vehicle control system was designed and built. The impact of this is that the control system did not have enough control authority to compensate for the effects of the first fundamental structural mode of the vehicle. As a result, the resulting pitch rate response of the vehicle was below specification and no post-design changes could recover the

  5. High Integrity Can Design Interfaces

    International Nuclear Information System (INIS)

    Shaber, E.L.

    1998-01-01

    The National Spent Nuclear Fuel Program is chartered with facilitating the disposition of DOE-owned spent nuclear fuel to allow disposal at a geologic repository. This is done through coordination with the repository program and by assisting DOE Site owners of SNF with needed information, standardized requirements, packaging approaches, etc. The High Integrity Can (HIC) will be manufactured to provide a substitute or barrier enhancement for normal fuel geometry and cladding. The can would be nested inside the DOE standardized canister which is designed to interface with the repository waste package. The HIC approach may provide the following benefits over typical canning approaches for DOE SNF. (a) It allows ready calculation and management of criticality issues for miscellaneous. (b) It segments and further isolates damaged or otherwise problem materials from normal SNF in the repository package. (c) It provides a very long term corrosion barrier. (d) It provides an extra internal pressure barrier for particulates, gaseous fission products, hydrogen, and water vapor. (e) It delays any potential release of fission products to the repository environment. (f) It maintains an additional level of fuel geometry control during design basis accidents, rock-fall, and seismic events. (g) When seal welded, it could provide the additional containment required for shipments involving plutonium content in excess of 20 Ci. (10 CFR 71.63.b) if integrated with an appropriate cask design. Long term corrosion protection is central to the HIC concept. The material selected for the HIC (Hastelloy C-22) has undergone extensive testing for repository service. The most severe theoretical interactions between iron, repository water containing chlorides and other repository construction materials have been tested. These expected chemical species have not been shown capable of corroding the selected HIC material. Therefore, the HIC should provide a significant barrier to DOE SNF dispersal

  6. Four Ways of Knowing: A Multidisciplinary Approach to Teaching Community-based Design

    Directory of Open Access Journals (Sweden)

    Sally Harrison

    2012-11-01

    Full Text Available Design education, especially in an undergraduate course of study, seeks to prepare students for professions and for citizenship in a world they hardly know. The studio typically provides only a surrogate experience in addressing formal and spatial problems, and is limited by time, by its geographic space, and by a dialogue that is more often than not, self-referential. It very rarely engages systemic questions of public policy, or the specific challenges of implementing at full scale ideas that are conceived through representational means. The constrained intellectual context is most poignantly seen in the urban design studios where problems are situated in the real world, and where issues outside the purview of design are found embedded in a place. Form-focused studio exercises that are necessarily a part of beginning architecture education are inadequate for exploring the indeterminacy of urban space and the complexity of human environments. When students enter an urban design studio, especially when they undertake community-based projects, they must take up the mantle of citizenship and engage in an enterprise that is fundamentally relational and grounded in experience. They need more information and more ways of knowing the world than traditionally the design disciplines can offer. This paper presents the outcomes of an experimental neighborhood-based teaching project undertaken as a collaboration among classes in architecture, landscape architecture, urban geography and the fine arts at Temple University. Although initiated through the architecture faculty’s desire to enrich its own undergraduate urban design studio, all the collaborators shared our concern about the narrowing effects of disciplinary bracketing on student learning, especially when the goal was to address real world situations. Each discipline brought to the project its particular disciplinary culture -- its language, methodology and areas of concern -- and a shared

  7. Towards Multidisciplinary HIV-Cure Research: Integrating Social Science with Biomedical Research.

    Science.gov (United States)

    Grossman, Cynthia I; Ross, Anna Laura; Auerbach, Judith D; Ananworanich, Jintanat; Dubé, Karine; Tucker, Joseph D; Noseda, Veronica; Possas, Cristina; Rausch, Dianne M

    2016-01-01

    The quest for a cure for HIV remains a timely and key challenge for the HIV research community. Despite significant scientific advances, current HIV therapy regimens do not completely eliminate the negative impact of HIV on the immune system; and the economic impact of treating all people infected with HIV globally, for the duration of their lifetimes, presents significant challenges. This article discusses, from a multidisciplinary approach, critical social, behavioral, ethical, and economic issues permeating the HIV-cure research agenda. As part of a search for an HIV cure, both the perspective of patients/participants and clinical researchers should be taken into account. In addition, continued efforts should be made to involve and educate the broader community. Published by Elsevier Ltd.

  8. Effectiveness of a multidisciplinary care program on recovery and return to work of patients after gynaecological surgery; design of a randomized controlled trial

    Directory of Open Access Journals (Sweden)

    Vonk Noordegraaf Antonie

    2012-02-01

    Full Text Available Abstract Background Return to work after gynaecological surgery takes much longer than expected, irrespective of the level of invasiveness. In order to empower patients in recovery and return to work, a multidisciplinary care program consisting of an e-health intervention and integrated care management including participatory workplace intervention was developed. Methods/Design We designed a randomized controlled trial to assess the effect of the multidisciplinary care program on full sustainable return to work in patients after gynaecological surgery, compared to usual clinical care. Two hundred twelve women (18-65 years old undergoing hysterectomy and/or laparoscopic adnexal surgery on benign indication in one of the 7 participating (university hospitals in the Netherlands are expected to take part in this study at baseline. The primary outcome measure is sick leave duration until full sustainable return to work and is measured by a monthly calendar of sickness absence during 26 weeks after surgery. Secondary outcome measures are the effect of the care program on general recovery, quality of life, pain intensity and complications, and are assessed using questionnaires at baseline, 2, 6, 12 and 26 weeks after surgery. Discussion The discrepancy between expected physical recovery and actual return to work after gynaecological surgery contributes to the relevance of this study. There is strong evidence that long periods of sick leave can result in work disability, poorer general health and increased risk of mental health problems. We expect that this multidisciplinary care program will improve peri-operative care, contribute to a faster return to work of patients after gynaecological surgery and, as a consequence, will reduce societal costs considerably. Trial registration Netherlands Trial Register (NTR: NTR2087

  9. Landing Gear Integration in Aircraft Conceptual Design. Revision

    Science.gov (United States)

    Chai, Sonny T.; Mason, William H.

    1997-01-01

    The design of the landing gear is one of the more fundamental aspects of aircraft design. The design and integration process encompasses numerous engineering disciplines, e.g., structure, weights, runway design, and economics, and has become extremely sophisticated in the last few decades. Although the design process is well-documented, no attempt has been made until now in the development of a design methodology that can be used within an automated environment. As a result, the process remains to be a key responsibility for the configuration designer and is largely experience-based and graphically-oriented. However, as industry and government try to incorporate multidisciplinary design optimization (MDO) methods in the conceptual design phase, the need for a more systematic procedure has become apparent. The development of an MDO-capable design methodology as described in this work is focused on providing the conceptual designer with tools to help automate the disciplinary analyses, i.e., geometry, kinematics, flotation, and weight. Documented design procedures and analyses were examined to determine their applicability, and to ensure compliance with current practices and regulations. Using the latest information as obtained from industry during initial industry survey, the analyses were in terms modified and expanded to accommodate the design criteria associated with the advanced large subsonic transports. Algorithms were then developed based on the updated analysis procedures to be incorporated into existing MDO codes.

  10. Deficiencies in provision of integrated multidisciplinary podiatry care for patients with inflammatory arthritis: a UK district general hospital experience.

    Science.gov (United States)

    Juarez, M; Price, E; Collins, D; Williamson, L

    2010-01-01

    Foot problems are highly prevalent in inflammatory arthritis (IA), especially rheumatoid arthritis (RA). Chronic inflammation can lead to permanent structural changes, deformity and disability. Early podiatry intervention in RA improves long term outcomes. National guidelines recommend that patients should be treated by a multidisciplinary team with dedicated podiatry services. In clinical practice funding constraints limit availability of these services. To assess prevalence of foot problems and quality and availability of foot care services at a UK district general hospital. 1200 IA patients in Swindon (Wiltshire, UK) were invited to complete an anonymised questionnaire regarding access to foot care services and education/information on foot problems. 448 patients. Prevalence of foot problems: 68%. Only 31% of patients had access to appropriate foot specialist. 24% had received foot assessment within 3 months of diagnosis of IA and 17% yearly review thereafter. Despite high prevalence of foot problems in our population we identified significant deficiencies in provision of integrated multidisciplinary podiatry care. The data we present could be used by others to support business cases to obtain funding to improve the links between rheumatology and podiatry services. Copyright 2010 Elsevier Ltd. All rights reserved.

  11. Impact of specialized multi-disciplinary approach and an integrated pathway on outcomes in hilar cholangiocarcinoma.

    Science.gov (United States)

    Gomez, D; Patel, P B; Lacasia-Purroy, C; Byrne, C; Sturgess, R P; Palmer, D; Fenwick, S; Poston, G J; Malik, H Z

    2014-01-01

    To assess the outcomes of patients with hilar cholangiocarcinoma following referral to a specialist multi-disciplinary team. Over an 11-year period, patients referred with hilar cholangiocarcinoma were identified from a prospectively maintained registry. Collated data included demographics, operative findings and histo-pathological data. Survival differences and prognostic factors were determined. 345 patients were referred with hilar cholangiocarcinoma, of which 57 (16.5%) patients had surgery. Prior to 2008, of 143 patients referred, only 17 (11.9%) patients underwent surgery, compared to 40 (19.8%) of 202 patients referred from 2008 onwards (p = 0.051). In the surgery group, the majority of patients underwent left hemi-hepatectomy (n = 19). In addition, portal vein (n = 5), hepatic artery (n = 2) and inferior vena cava (n = 3) resections were performed. The R0 resection rate was 73.7%. The morbidity and mortality rates were 59.6% and 14.0%, respectively. The median disease-free survival was 16 (4-101) months. The presence of lymph node metastasis (p = 0.002) was the only predictor of poorer disease-free survival. The 5-year overall survival was 39.5% and was significantly better than that of the palliative group (p hilar cholangiocarcinoma and is associated with better overall survival. Prompt referral to tertiary centres with a core team of clinicians to manage this difficult condition may allow more patients to come to potentially curative surgical resections. Copyright © 2013. Published by Elsevier Ltd.

  12. Effectiveness of a multidisciplinary care program on recovery and return to work of patients after gynaecological surgery; design of a randomized controlled trial.

    Science.gov (United States)

    Vonk Noordegraaf, Antonie; Huirne, Judith A F; Brölmann, Hans A M; Emanuel, Mark H; van Kesteren, Paul J M; Kleiverda, Gunilla; Lips, Jos P; Mozes, Alexander; Thurkow, Andreas L; van Mechelen, Willem; Anema, Johannes R

    2012-02-01

    Return to work after gynaecological surgery takes much longer than expected, irrespective of the level of invasiveness. In order to empower patients in recovery and return to work, a multidisciplinary care program consisting of an e-health intervention and integrated care management including participatory workplace intervention was developed. We designed a randomized controlled trial to assess the effect of the multidisciplinary care program on full sustainable return to work in patients after gynaecological surgery, compared to usual clinical care. Two hundred twelve women (18-65 years old) undergoing hysterectomy and/or laparoscopic adnexal surgery on benign indication in one of the 7 participating (university) hospitals in the Netherlands are expected to take part in this study at baseline. The primary outcome measure is sick leave duration until full sustainable return to work and is measured by a monthly calendar of sickness absence during 26 weeks after surgery. Secondary outcome measures are the effect of the care program on general recovery, quality of life, pain intensity and complications, and are assessed using questionnaires at baseline, 2, 6, 12 and 26 weeks after surgery. The discrepancy between expected physical recovery and actual return to work after gynaecological surgery contributes to the relevance of this study. There is strong evidence that long periods of sick leave can result in work disability, poorer general health and increased risk of mental health problems. We expect that this multidisciplinary care program will improve peri-operative care, contribute to a faster return to work of patients after gynaecological surgery and, as a consequence, will reduce societal costs considerably. Netherlands Trial Register (NTR): NTR2087.

  13. Multidisciplinary design optimization of the belt drive system considering both structure and vibration characteristics based on improved genetic algorithm

    Science.gov (United States)

    Yuan, Yongliang; Song, Xueguan; Sun, Wei; Wang, Xiaobang

    2018-05-01

    The dynamic performance of a belt drive system is composed of many factors, such as the efficiency, the vibration, and the optimal parameters. The conventional design only considers the basic performance of the belt drive system, while ignoring its overall performance. To address all these challenges, the study on vibration characteristics and optimization strategies could be a feasible way. This paper proposes a new optimization strategy and takes a belt drive design optimization as a case study based on the multidisciplinary design optimization (MDO). The MDO of the belt drive system is established and the corresponding sub-systems are analyzed. The multidisciplinary optimization is performed by using an improved genetic algorithm. Based on the optimal results obtained from the MDO, the three-dimension (3D) model of the belt drive system is established for dynamics simulation by virtual prototyping. From the comparison of the results with respect to different velocities and loads, the MDO method can effectively reduce the transverse vibration amplitude. The law of the vibration displacement, the vibration frequency, and the influence of velocities on the transverse vibrations has been obtained. Results show that the MDO method is of great help to obtain the optimal structural parameters. Furthermore, the kinematics principle of the belt drive has been obtained. The belt drive design case indicates that the proposed method in this paper can also be used to solve other engineering optimization problems efficiently.

  14. MUSE: Challenges to integrate the Multi-Disciplinary field of BB access in one project

    NARCIS (Netherlands)

    Fatome, J.; Pitois, S.; Kamagate, A.; Maillotte, H.; Massoubre., D.; González-Herráez, G.-H.; Smedt, A. de; Brink, R. van den

    2006-01-01

    The present paper discusses the managerial challenges of the MUSE integrated project on multi service broadband access. It addresses different aspects such as matrix organisation, project office, consensus process, standardisation, dissemination, and quality control.

  15. Integrated Radiation Analysis and Design Tools

    Data.gov (United States)

    National Aeronautics and Space Administration — The Integrated Radiation Analysis and Design Tools (IRADT) Project develops and maintains an integrated tool set that collects the current best practices, databases,...

  16. Transitions of Care Between Acute and Chronic Heart Failure: Critical Steps in the Design of a Multidisciplinary Care Model for the Prevention of Rehospitalization.

    Science.gov (United States)

    Comín-Colet, Josep; Enjuanes, Cristina; Lupón, Josep; Cainzos-Achirica, Miguel; Badosa, Neus; Verdú, José María

    2016-10-01

    Despite advances in the treatment of heart failure, mortality, the number of readmissions, and their associated health care costs are very high. Heart failure care models inspired by the chronic care model, also known as heart failure programs or heart failure units, have shown clinical benefits in high-risk patients. However, while traditional heart failure units have focused on patients detected in the outpatient phase, the increasing pressure from hospital admissions is shifting the focus of interest toward multidisciplinary programs that concentrate on transitions of care, particularly between the acute phase and the postdischarge phase. These new integrated care models for heart failure revolve around interventions at the time of transitions of care. They are multidisciplinary and patient-centered, designed to ensure continuity of care, and have been demonstrated to reduce potentially avoidable hospital admissions. Key components of these models are early intervention during the inpatient phase, discharge planning, early postdischarge review and structured follow-up, advanced transition planning, and the involvement of physicians and nurses specialized in heart failure. It is hoped that such models will be progressively implemented across the country. Copyright © 2016 Sociedad Española de Cardiología. Published by Elsevier España, S.L.U. All rights reserved.

  17. Multidisciplinary design and analytic approaches to advance prospective research on the multilevel determinants of child health.

    Science.gov (United States)

    Johnson, Sara B; Little, Todd D; Masyn, Katherine; Mehta, Paras D; Ghazarian, Sharon R

    2017-06-01

    Characterizing the determinants of child health and development over time, and identifying the mechanisms by which these determinants operate, is a research priority. The growth of precision medicine has increased awareness and refinement of conceptual frameworks, data management systems, and analytic methods for multilevel data. This article reviews key methodological challenges in cohort studies designed to investigate multilevel influences on child health and strategies to address them. We review and summarize methodological challenges that could undermine prospective studies of the multilevel determinants of child health and ways to address them, borrowing approaches from the social and behavioral sciences. Nested data, variation in intervals of data collection and assessment, missing data, construct measurement across development and reporters, and unobserved population heterogeneity pose challenges in prospective multilevel cohort studies with children. We discuss innovations in missing data, innovations in person-oriented analyses, and innovations in multilevel modeling to address these challenges. Study design and analytic approaches that facilitate the integration across multiple levels, and that account for changes in people and the multiple, dynamic, nested systems in which they participate over time, are crucial to fully realize the promise of precision medicine for children and adolescents. Copyright © 2017 Elsevier Inc. All rights reserved.

  18. Intraoperative computed tomography with integrated navigation system in a multidisciplinary operating suite.

    Science.gov (United States)

    Uhl, Eberhard; Zausinger, Stefan; Morhard, Dominik; Heigl, Thomas; Scheder, Benjamin; Rachinger, Walter; Schichor, Christian; Tonn, Jörg-Christian

    2009-05-01

    in the existing surgical protocol and work flow. Imaging and updating of the NNS can be performed at any time during surgery with very limited time and modification of the surgical setup. Multidisciplinary use increases utilization of the system and thus improves the cost-efficiency relationship.

  19. Integrating Augmented Reality in Higher Education: A Multidisciplinary Study of Student Perceptions

    Science.gov (United States)

    Delello, Julie A.; McWhorter, Rochell R.; Camp, Kerri M.

    2015-01-01

    Augmented reality (AR) is an emerging technology that blends physical objects with virtual reality. Through the integration of digital and print media, a gap between the "on and offline" worlds are merged, radically shifting student-computer interaction in the classroom. This research examined the results of a multiple case study on the…

  20. Developing a Participatory Pedagogical and Multidisciplinary Approach for Integrating HIV/AIDS into University Curriculum

    Science.gov (United States)

    Mulwo, Abraham Kiprop; Chemai, Lemmy

    2015-01-01

    The current framework for integrating HIV/AIDS into university curriculum is mainly informed by the need to make HIV/AIDS education relevant to specific disciplines, and to equip graduates with necessary skills to respond to HIV/AIDS in their professional capacities. This strategy mainly emphasizes content and knowledge and largely ignores the…

  1. Issues and Challenges Identified in the Development of a Broad Multidisciplinary Work Integrated Learning Package

    Science.gov (United States)

    Sutherland, Karen; Symmons, Mark

    2013-01-01

    Work integrated learning (WIL) units can be discipline specific and constructed for majors or degrees with a strong vocational orientation. This paper describes an undergraduate unit with its genesis in a public relations internship. The original unit enjoyed strong support from industry partners and was instrumental in many graduates securing…

  2. Integrated design and engineering using Building Information Modelling: A pilot project of small-scale housing development in The Netherlands

    NARCIS (Netherlands)

    Sebastian, R.

    2010-01-01

    During the design phase, decisions aremade that affect, on average, 70% of the life-cycle cost of a building. Therefore, collaborative design relying on multidisciplinary knowledge of the building life cycle is essential. Building information modelling (BIM) makes it possible to integrate knowledge

  3. Augmented Reality for Multi-disciplinary Collaboration

    OpenAIRE

    Wang, Xiangyu; Rui,

    2010-01-01

    This chapter presents a framework for multi-disciplinary collaboration. Tangible Augmented Reality has been raised as one of suitable systems for design collaboration. Furthermore, it emphasizes the advantages of Tangible Augmented Reality to illustrate the needs for integrating the Tangible User Interfaces and Augmented Reality Systems.

  4. The Saale-Project -A multidisciplinary approach towards sustainable integrative catchment management -

    Science.gov (United States)

    Bongartz, K.; Flügel, W. A.

    2003-04-01

    In the joint research project “Development of an integrated methodology for the sustainable management of river basins The Saale River Basin example”, coordinated by the Centre of Environmental Research (UFZ), concepts and tools for an integrated management of large river basins are developed and applied for the Saale river basin. The ultimate objective of the project is to contribute to the holistic assessment and benchmarking approaches in water resource planning, as required by the European Water Framework Directive. The study presented here deals (1) with the development of a river basin information and modelling system, (2) with the refinement of a regionalisation approach adapted for integrated basin modelling. The approach combines a user friendly basin disaggregation method preserving the catchment’s physiographic heterogeneity with a process oriented hydrological basin assessment for scale bridging integrated modelling. The well tested regional distribution concept of Response Units (RUs) will be enhanced by landscape metrics and decision support tools for objective, scale independent and problem oriented RU delineation to provide the spatial modelling entities for process oriented and distributed simulation of vertical and lateral hydrological transport processes. On basis of this RUs suitable hydrological modelling approaches will be further developed with strong respect to a more detailed simulation of the lateral surface and subsurface flows as well as the channel flow. This methodical enhancement of the well recognised RU-concept will be applied to the river basin of the Saale (Ac: 23 179 km2) and validated by a nested catchment approach, which allows multi-response-validation and estimation of uncertainties of the modelling results. Integrated modelling of such a complex basin strongly influenced by manifold human activities (reservoirs, agriculture, urban areas and industry) can only be achieved by coupling the various modelling approaches

  5. Multidisciplinary design and optimization of a plastic injection mold using an integrated design and engineering environment

    NARCIS (Netherlands)

    Van Dijk, R.E.C.; d’Ippolito, R.; Tosi, G.; La Rocca, G.

    2011-01-01

    In order to remain competitive with respect to low-cost overseas markets, domestic moldmakers will have to increase the productivity of their engineers and maintain high quality standard, while dealing with the problem of an aging workforce. To increase the competitiveness of the European automotive

  6. Integrating reliability analysis and design

    International Nuclear Information System (INIS)

    Rasmuson, D.M.

    1980-10-01

    This report describes the Interactive Reliability Analysis Project and demonstrates the advantages of using computer-aided design systems (CADS) in reliability analysis. Common cause failure problems require presentations of systems, analysis of fault trees, and evaluation of solutions to these. Results have to be communicated between the reliability analyst and the system designer. Using a computer-aided design system saves time and money in the analysis of design. Computer-aided design systems lend themselves to cable routing, valve and switch lists, pipe routing, and other component studies. At EG and G Idaho, Inc., the Applicon CADS is being applied to the study of water reactor safety systems

  7. Integrated design for space transportation system

    CERN Document Server

    Suresh, B N

    2015-01-01

    The book addresses the overall integrated design aspects of a space transportation system involving several disciplines like propulsion, vehicle structures, aerodynamics, flight mechanics, navigation, guidance and control systems, stage auxiliary systems, thermal systems etc. and discusses the system approach for design, trade off analysis, system life cycle considerations, important aspects in mission management, the risk assessment, etc. There are several books authored to describe the design aspects of various areas, viz., propulsion, aerodynamics, structures, control, etc., but there is no book which presents space transportation system (STS) design in an integrated manner. This book attempts to fill this gap by addressing systems approach for STS design, highlighting the integrated design aspects, interactions between various subsystems and interdependencies. The main focus is towards the complex integrated design to arrive at an optimum, robust and cost effective space transportation system. The orbit...

  8. Multi-Disciplinary Research Experiences Integrated with Industry –Field Experiences

    Directory of Open Access Journals (Sweden)

    Suzanne Lunsford

    2015-10-01

    Full Text Available The purpose of this environmentally inquiry-based lab was to allow the students to engage into real-world concepts that integrate industry setting (Ohio Aggregate Industrial Mineral Association with the academia setting. Our students are engaged into a field trip where mining occurs to start the problem based learning of how the heavy metals leak in the mining process. These heavy metals such as lead and indium in the groundwater are a serious concern for the environment (Environmental Protection Agency from the mining process. The field experiences at the mining process assist in building our students interest in developing sensors to detect heavy metals of concern such as lead and indium simultaneously by a unique electrochemistry technique called Square Wave Anodic Stripping Voltammetry (SWASV. The field experience assists building the students interest in real –world application and what qualities do they want the electrochemical sensor to possess to be successful for real world usage. During the field trip the students are engaged into learning novel instrumentation such as an SEM (Scanning Electron Microscope to study the working electrode sensor developed to understand the sensor surface morphology properties better as well. The integration of industry setting with academia has been a positive experience for our students that has allowed their understanding of real-world science research needs to succeed in an industrial setting of research.

  9. Challenges of Aircraft Design Integration

    Science.gov (United States)

    2003-03-01

    predicted by the conceptual stick model and the full FEM of the Challenger wing without winglets . Advanced aerodynamic wing design methods To design wings...Piperni, E. Laurendeau Advanced Aerodynamics Bombardier Aerospace 400 CMte Vertu Road Dorval, Quebec, Canada, H4S 1Y9 Fassi.Kafyeke @notes.canadair.ca Tel...514) 855-7186 Abstract The design of a modern airplane brings together many disciplines: structures, aerodynamics , controls, systems, propulsion

  10. Passive solar offices: integrated design

    Energy Technology Data Exchange (ETDEWEB)

    Evans, B

    1992-05-06

    Passive solar design in out-of-town offices can remove the need for air-conditioning by making greater use of daylight and natural ventilation. To promote the use of passive solar energy a series of design studies are being run by the Energy Technology Support Unit on behalf of the Department of Energy. The three reported here are designs for out-of-town business buildings. Each is a hypothetical building designed to a realistic brief for an organisation taking the role of real client. (author).

  11. Integrating product design into the supply chain

    DEFF Research Database (Denmark)

    Khan, Omera; Stolte, Terje; Creazza, Alessandro

    2016-01-01

    Purpose: The aim of the research is to illustrate how companies can create competitive capabilities through integration of product design into the supply chain. In doing so the paper reveals the challenges and the opportunities that companies face when integrating product design and supply chain...... of opportunities and challenges when integrating product design and the supply chain and subsequently a step-by-step guide is developed to address these. Practical Implications: The research provides key recommendations to companies on how to create competitive capabilities by integrating product design...... into the supply chain. Originality/Value: This paper provides novel insights to both practitioners and researchers. For practitioners detailed recommendations are given on how they can maximise benefits through integrating product design into the supply chain. The RBV has been harnessed to highlight how...

  12. Integrating product design into the supply chain

    DEFF Research Database (Denmark)

    Khan, Omera; Stolte, Terje; Creazza, Alessandro

    2016-01-01

    into the supply chain. Originality/Value: This paper provides novel insights to both practitioners and researchers. For practitioners detailed recommendations are given on how they can maximise benefits through integrating product design into the supply chain. The RBV has been harnessed to highlight how......Purpose: The aim of the research is to illustrate how companies can create competitive capabilities through integration of product design into the supply chain. In doing so the paper reveals the challenges and the opportunities that companies face when integrating product design and supply chain...... of opportunities and challenges when integrating product design and the supply chain and subsequently a step-by-step guide is developed to address these. Practical Implications: The research provides key recommendations to companies on how to create competitive capabilities by integrating product design...

  13. Inside the polygonal walls of Amelia (Central Italy): A multidisciplinary data integration, encompassing geodetic monitoring and geophysical prospections

    Science.gov (United States)

    Ercoli, M.; Brigante, R.; Radicioni, F.; Pauselli, C.; Mazzocca, M.; Centi, G.; Stoppini, A.

    2016-04-01

    We investigate a portion of the ancient (VI and IV centuries BC) polygonal walls of Amelia, in Central Italy. After the collapse of a portion of the walls which occurred in January 2006, a wide project started in order to monitor their external facade and inspect the characteristics of the internal structure, currently not clearly known. In this specific case, the preservation of such an important cultural heritage was mandatory, therefore invasive methods like drilling or archaeological essays cannot be used. For this purpose, a multidisciplinary approach represents an innovative way to shed light on their inner structure. We combine several non-invasive techniques such as Ground Penetrating Radar (GPR) and Electrical Resistivity Tomography (ERT), specifically adapted for this study, Laser Scanning and Digital Terrestrial Photogrammetry, integrated with other geomatic measures provided by a Total Station and Global Navigation Satellite Systems (GNSS). After collecting some historical information, we gather the whole datasets exploring for their integration an interpretation approach borrowed from the reflection seismic (attribute analysis and three dimensional visualization). The results give rise for the first time to the internal imaging of this ancient walls, highlighting features associable to different building styles related to different historical periods. Among the result, we define a max wall thickness of about 3.5 m for the cyclopic sector, we show details of the internal block organization and we detect low resistivity values interpretable with high water content behind the basal part of the walls. Then, quantitative analyses to assess their reliable geotechnical stability are done, integrating new geometrical constrains provided by the geophysics and geo-technical ground parameters available in literature. From this analysis, we highlight how the Amelia walls are interested, in the investigated sector, by a critical pseudo-static equilibrium.

  14. Intergenerational Transmission of Self-Regulation: A Multidisciplinary Review and Integrative Conceptual Framework

    Science.gov (United States)

    Bridgett, David J.; Burt, Nicole M.; Edwards, Erin S.; Deater-Deckard, Kirby

    2014-01-01

    This review examines mechanisms contributing to the intergenerational transmission of self-regulation. To provide an integrated account of how self-regulation is transmitted across generations, we draw from over 75 years of accumulated evidence, spanning case studies to experimental approaches, in literatures covering developmental, social, and clinical psychology, and criminology, physiology, genetics, and human and animal neuroscience (among others). First, we present a taxonomy of what self-regulation is and then examine how it develops – overviews that guide the main foci of the review. Next, studies supporting an association between parent and child self-regulation are reviewed. Subsequently, literature that considers potential social mechanisms of transmission, specifically parenting behavior, inter-parental (i.e., marital) relationship behaviors, and broader rearing influences (e.g., household chaos) are considered. Finally, literature providing evidence that prenatal programming may be the starting point of the intergenerational transmission of self-regulation is covered, along with key findings from the behavioral and molecular genetics literatures. To integrate these literatures, we introduce the Self-Regulation Intergenerational Transmission Model, a framework that brings together prenatal, social, and neurobiological mechanisms (spanning endocrine, neural, and genetic levels, including gene-environment interplay and epigenetic processes) to explain the intergenerational transmission of self-regulation. This model also incorporates potential transactional processes between generations (e.g., children’s self-regulation and parent-child interaction dynamics that may affect parents’ self-regulation) that further influence intergenerational processes. In pointing the way forward, we note key future directions and ways to address limitations in existing work throughout the review and in closing. We also conclude by noting several implications for

  15. Integrating ergonomic knowledge into engineering design processes

    DEFF Research Database (Denmark)

    Hall-Andersen, Lene Bjerg

    Integrating ergonomic knowledge into engineering design processes has been shown to contribute to healthy and effective designs of workplaces. However, it is also well-recognized that, in practice, ergonomists often have difficulties gaining access to and impacting engineering design processes...... employed in the same company, constituted a supporting factor for the possibilities to integrate ergonomic knowledge into the engineering design processes. However, the integration activities remained discrete and only happened in some of the design projects. A major barrier was related to the business...... to the ergonomic ambitions of the clients. The ergonomists’ ability to navigate, act strategically, and compromise on ergonomic inputs is also important in relation to having an impact in the engineering design processes. Familiarity with the engineering design terminology and the setup of design projects seems...

  16. A multi-disciplinary approach for the integrated assessment of multiple risks in delta areas.

    Science.gov (United States)

    Sperotto, Anna; Torresan, Silvia; Critto, Andrea; Marcomini, Antonio

    2016-04-01

    The assessment of climate change related risks is notoriously difficult due to the complex and uncertain combinations of hazardous events that might happen, the multiplicity of physical processes involved, the continuous changes and interactions of environmental and socio-economic systems. One important challenge lies in predicting and modelling cascades of natural and man -made hazard events which can be triggered by climate change, encompassing different spatial and temporal scales. Another regard the potentially difficult integration of environmental, social and economic disciplines in the multi-risk concept. Finally, the effective interaction between scientists and stakeholders is essential to ensure that multi-risk knowledge is translated into efficient adaptation and management strategies. The assessment is even more complex at the scale of deltaic systems which are particularly vulnerable to global environmental changes, due to the fragile equilibrium between the presence of valuable natural ecosystems and relevant economic activities. Improving our capacity to assess the combined effects of multiple hazards (e.g. sea-level rise, storm surges, reduction in sediment load, local subsidence, saltwater intrusion) is therefore essential to identify timely opportunities for adaptation. A holistic multi-risk approach is here proposed to integrate terminology, metrics and methodologies from different research fields (i.e. environmental, social and economic sciences) thus creating shared knowledge areas to advance multi risk assessment and management in delta regions. A first testing of the approach, including the application of Bayesian network analysis for the assessment of impacts of climate change on key natural systems (e.g. wetlands, protected areas, beaches) and socio-economic activities (e.g. agriculture, tourism), is applied in the Po river delta in Northern Italy. The approach is based on a bottom-up process involving local stakeholders early in different

  17. Integration of multidisciplinary technologies for real time target visualization and verification for radiotherapy.

    Science.gov (United States)

    Chang, Wen-Chung; Chen, Chin-Sheng; Tai, Hung-Chi; Liu, Chia-Yuan; Chen, Yu-Jen

    2014-01-01

    The current practice of radiotherapy examines target coverage solely from digitally reconstructed beam's eye view (BEV) in a way that is indirectly accessible and that is not in real time. We aimed to visualize treatment targets in real time from each BEV. The image data of phantom or patients from ultrasound (US) and computed tomography (CT) scans were captured to perform image registration. We integrated US, CT, US/CT image registration, robotic manipulation of US, a radiation treatment planning system, and a linear accelerator to constitute an innovative target visualization system. The performance of this algorithm segmented the target organ in CT images, transformed and reconstructed US images to match each orientation, and generated image registration in real time mode with acceptable accuracy. This image transformation allowed physicians to visualize the CT image-reconstructed target via a US probe outside the BEV that was non-coplanar to the beam's plane. It allowed the physicians to remotely control the US probe that was equipped on a robotic arm to dynamically trace and real time monitor the coverage of the target within the BEV during a simulated beam-on situation. This target visualization system may provide a direct remotely accessible and real time way to visualize, verify, and ensure tumor targeting during radiotherapy.

  18. Development of a Medication Monitoring System for an Integrated Multidisciplinary Program of Assertive Community Treatment (IMPACT Team

    Directory of Open Access Journals (Sweden)

    Nicole B. Washington, DO, Assistant Professor

    2012-01-01

    Full Text Available Purpose: The primary goal was to improve medication management oversight for a severely mentally ill (SMI community-based population by developing a medication monitoring system based on current guidelines to optimize pharmacotherapy and minimize potential medication-related adverse effects. The secondary goal was improvement in coordination of care between healthcare providers. Methods: Guidelines for medication used for psychiatric indications were reviewed. A database of medication for psychiatric indications with monitoring recommendation was developed. Results: Medication regimens for 68 members of the Integrated Multidisciplinary Program of Assertive Community Treatment (IMPACT program qualified for review. Fourteen medications, carbamazepine, chlorpromazine, clozapine, fluphenazine and fluphenazine long-acting injections (LAI, haloperidol and haloperidol LAI, lithium, lurasidone, olanzapine, paliperidone and paliperidone LAI, perphenazine, quetiapine, risperidone and risperidone LAI, valproic acid/divalproex, and ziprasidone, were identified. In total, 111 medications are used on a monthly basis. Each member receives more than one medication qualifying for review. Additional monitoring parameters that were evaluated included changes in laboratory orders for members with insulin-dependent diabetes. Annual lipid panels were changed to every 6 months, if applicable. Conclusions and Future Directions: This medication monitoring program was developed to help ensure IMPACT members receive the most effective care and minimize potential medication-related adverse effects. The secondary goal was to improve coordination of care. Medication monitoring will be added as a continuous quality assurance measure. Lab results will be reviewed at least monthly. The medication monitoring program will be evaluated annually.

  19. Neoplastic pleural effusion and intrathoracic metastasis of a scapular osteosarcoma in a dog: a multidisciplinary integrated diagnostic approach.

    Science.gov (United States)

    Mesquita, Luis; Mortier, Jeremy; Ressel, Lorenzo; Finotello, Riccardo; Silvestrini, Paolo; Piviani, Martina

    2017-06-01

    A 10-year-old, female spayed mixed-breed or cross-bred dog was referred to the Small Animal Teaching Hospital of the University of Liverpool due to tachypnea, dyspnea, and pleural effusion not responding to diuretics and antibiotics. The chest was drained and cytology of the pleural fluid was consistent with a modified transudate with presence of atypical cells initially attributed to mesothelial hyperplasia and dysplasia. Computed tomography detected, in addition to the bilateral pleural effusion, diffuse pleural thickening, multiple pleural and pulmonary nodules, and a mineralized and lytic mass in the left scapula. Imaging findings were suggestive of a primary bone tumor with intrathoracic metastasis. Cytology of the left scapular and pleural masses revealed a malignant neoplasm highly suggestive of osteosarcoma. The diagnosis was confirmed by demonstration of a positive cytochemical reaction for alkaline phosphatase on prestained cytology slides. This finding prompted review of the initial interpretation of the pleural effusion cytology. The presence of neoplastic osteoblasts in the thoracic fluid was identified by a combination of cytochemistry, cell pellet immunohistochemistry, and transmission electron microscopy findings. In this report, a multidisciplinary integrated diagnostic approach was used to diagnose and confirm a neoplastic pleural effusion due to osteosarcoma metastasis in a dog. © 2017 American Society for Veterinary Clinical Pathology.

  20. Decision-Based Design Integrating Consumer Preferences into Engineering Design

    CERN Document Server

    Chen, Wei; Wassenaar, Henk Jan

    2013-01-01

    Building upon the fundamental principles of decision theory, Decision-Based Design: Integrating Consumer Preferences into Engineering Design presents an analytical approach to enterprise-driven Decision-Based Design (DBD) as a rigorous framework for decision making in engineering design.  Once the related fundamentals of decision theory, economic analysis, and econometrics modelling are established, the remaining chapters describe the entire process, the associated analytical techniques, and the design case studies for integrating consumer preference modeling into the enterprise-driven DBD framework. Methods for identifying key attributes, optimal design of human appraisal experiments, data collection, data analysis, and demand model estimation are presented and illustrated using engineering design case studies. The scope of the chapters also provides: •A rigorous framework of integrating the interests from both producer and consumers in engineering design, •Analytical techniques of consumer choice model...

  1. [Application of digital design of orthodontic-prosthodontic multidisciplinary treatment plan in esthetic rehabilitation of anterior teeth].

    Science.gov (United States)

    Liu, Y S; Li, Z; Zhao, Y J; Ye, H Q; Zhou, Y Q; Hu, W J; Liu, Y S; Xun, C L; Zhou, Y S

    2018-02-18

    To develop a digital workflow of orthodontic-prosthodontic multidisciplinary treatment plan which can be applied in complicated anterior teeth esthetic rehabilitation, in order to enhance the efficiency of communication between dentists and patients, and improve the predictability of treatment outcome. Twenty patients with the potential needs of orthodontic-prosthodontic multidisciplinary treatment to solve their complicated esthetic problems in anterior teeth were recruited in this study. Digital models of patients' both dental arches and soft tissues were captured using intra oral scanner. Direct prosthodontic (DP) treatment plan and orthodontic-prosthodontic (OP) treatment plan were carried out for each patient. For DP treatment plans, digital wax-up models were directly designed on original digital models using prosthodontic design system. For OP treatment plans, virtual-setups were performed using orthodontic analyze system according to orthodontic and esthetic criteria and imported to prosthodontic design system to finalize the digital wax-up models. These two treatment plans were shown to the patients and demonstrated elaborately. Each patient rated two treatment plans using visual analogue scales and the medians of scores of two treatment plans were analyzed using signed Wilcoxon test. Having taken into consideration various related factors, including time, costs of treatment, each patient chose a specific treatment plan. For the patients chose DP treatment plans, digital wax-up models were exported and printed into resin diagnostic models which would be utilized in the prosthodontic treatment process. For the patients chose OP treatment plans, virtual-setups were used to fabricate aligners or indirect bonding templates and digital wax-up models were also exported and printed into resin diagnostic models for prosthodontic treatment after orthodontic treatment completed. The medians of scores of DP treatment plan and OP treatment plan were calculated and

  2. Integration of multidisciplinary technologies for real time target visualization and verification for radiotherapy

    Directory of Open Access Journals (Sweden)

    Chang WC

    2014-06-01

    Full Text Available Wen-Chung Chang,1,* Chin-Sheng Chen,2,* Hung-Chi Tai,3 Chia-Yuan Liu,4,5 Yu-Jen Chen3 1Department of Electrical Engineering, National Taipei University of Technology, Taipei, Taiwan; 2Graduate Institute of Automation Technology, National Taipei University of Technology, Taipei, Taiwan; 3Department of Radiation Oncology, Mackay Memorial Hospital, Taipei, Taiwan; 4Department of Internal Medicine, Mackay Memorial Hospital, Taipei, Taiwan; 5Department of Medicine, Mackay Medical College, New Taipei City, Taiwan  *These authors contributed equally to this work Abstract: The current practice of radiotherapy examines target coverage solely from digitally reconstructed beam's eye view (BEV in a way that is indirectly accessible and that is not in real time. We aimed to visualize treatment targets in real time from each BEV. The image data of phantom or patients from ultrasound (US and computed tomography (CT scans were captured to perform image registration. We integrated US, CT, US/CT image registration, robotic manipulation of US, a radiation treatment planning system, and a linear accelerator to constitute an innovative target visualization system. The performance of this algorithm segmented the target organ in CT images, transformed and reconstructed US images to match each orientation, and generated image registration in real time mode with acceptable accuracy. This image transformation allowed physicians to visualize the CT image-reconstructed target via a US probe outside the BEV that was non-coplanar to the beam's plane. It allowed the physicians to remotely control the US probe that was equipped on a robotic arm to dynamically trace and real time monitor the coverage of the target within the BEV during a simulated beam-on situation. This target visualization system may provide a direct remotely accessible and real time way to visualize, verify, and ensure tumor targeting during radiotherapy. Keywords: ultrasound, computerized tomography

  3. Pragmatic trial of a multidisciplinary lung cancer care model in a community healthcare setting: study design, implementation evaluation, and baseline clinical results

    Science.gov (United States)

    Smeltzer, Matthew P.; Rugless, Fedoria E.; Jackson, Bianca M.; Berryman, Courtney L.; Faris, Nicholas R.; Ray, Meredith A.; Meadows, Meghan; Patel, Anita A.; Roark, Kristina S.; Kedia, Satish K.; DeBon, Margaret M.; Crossley, Fayre J.; Oliver, Georgia; McHugh, Laura M.; Hastings, Willeen; Osborne, Orion; Osborne, Jackie; Ill, Toni; Ill, Mark; Jones, Wynett; Lee, Hyo K.; Signore, Raymond S.; Fox, Roy C.; Li, Jingshan; Robbins, Edward T.; Ward, Kenneth D.; Klesges, Lisa M.

    2018-01-01

    Background Responsible for 25% of all US cancer deaths, lung cancer presents complex care-delivery challenges. Adoption of the highly recommended multidisciplinary care model suffers from a dearth of good quality evidence. Leading up to a prospective comparative-effectiveness study of multidisciplinary vs. serial care, we studied the implementation of a rigorously benchmarked multidisciplinary lung cancer clinic. Methods We used a mixed-methods approach to conduct a patient-centered, combined implementation and effectiveness study of a multidisciplinary model of lung cancer care. We established a co-located multidisciplinary clinic to study the implementation of this care-delivery model. We identified and engaged key stakeholders from the onset, used their input to develop the program structure, processes, performance benchmarks, and study endpoints (outcome-related process measures, patient- and caregiver-reported outcomes, survival). In this report, we describe the study design, process of implementation, comparative populations, and how they contrast with patients within the local and regional healthcare system. Trial Registration: ClinicalTrials.gov Identifier: NCT02123797. Results Implementation: the multidisciplinary clinic obtained an overall treatment concordance rate of 90% (target >85%). Satisfaction scores were high, with >95% of patients and caregivers rating themselves as being “very satisfied” with all aspects of care from the multidisciplinary team (patient/caregiver response rate >90%). The Reach of the multidisciplinary clinic included a higher proportion of minority patients, more women, and younger patients than the regional population. Comparative effectiveness: The comparative effectiveness trial conducted in the last phase of the study met the planned enrollment per statistical design, with 178 patients in the multidisciplinary arm and 348 in the serial care arm. The multidisciplinary cohort had older age and a higher percentage of racial

  4. A multidisciplinary, integrated approach for the elimination of schistosomiasis: a longitudinal study in a historically hyper-endemic region in the lower reaches of the Yangtze River, China from 2005 to 2014.

    Science.gov (United States)

    Sun, Le-Ping; Wang, Wei; Zuo, Yin-Ping; Hong, Qing-Biao; Du, Guang-Lin; Ma, Yu-Cai; Wang, Jian; Yang, Guo-Jing; Zhu, Dao-Jian; Liang, You-Sheng

    2017-03-14

    Although great success has been achieved, schistosomiasis remains a major public health concern in China, and the remaining core endemic regions are concentrated along the middle and lower reaches of the Yangtze River. In this longitudinal study, we evaluated the effectiveness of a multidisciplinary, integrated approach for schistosomiasis elimination in a historically hyper-endemic region in the lower reaches of the Yangtze River, China over the 10-year period from 2005 through 2014. A three-step roadmap for schistosomiasis elimination was designed in the study site, and multidisciplinary, integrated interventions were implemented by the health, agriculture, water resources development, land and resources, and forestry sectors from 2005 to 2014, including chemotherapy for infected individuals, health education, management of the source of Schistosoma japonicum infection, and intermediate host snail control. The annual number of schistosomiasis patients, S. japonicum infection in humans, bovines and Oncomelania hupensis snails, and water infectivity were observed to assess the effectiveness of the multidisciplinary, integrated approach for the elimination of schistosomiasis. There was a tendency towards a gradual decline in both the number of schistosomiasis cases and the prevalence of S. japonicum human infection across the study period from 2005 through 2014. No S. japonicum human infection was detected since 2012, and no acute infection was seen since 2006. During the study period, no infection was found in bovines, and a 0.03% overall infection rate was observed in O. hupensis snails. Since 2009, no infected snails were identified, and the area of both snail habitats and infected snail habitats appeared a reduction over the study period. Following the 3-year multidisciplinary, integrated control, infection control was achieved, and transmission control was achieved after 6-year implementation, with all infected snails and water infectivity eliminated; in

  5. Hudson Canyon benthic habitats characterization and mapping by integrated analysis of multidisciplinary data

    Science.gov (United States)

    Pierdomenico, Martina; Guida, Vincent G.; Rona, Peter A.; Macelloni, Leonardo; Scranton, Mary I.; Asper, Vernon; Diercks, Arne

    2013-04-01

    . Previously described hummocky terrain associated with extensive, long-term burrowing activity by golden tilefish (Lopholatilus chamaeleonticeps) was clearly delineated along the canyon rims. Bedform fields and potential current deposits observed along the upper portion of canyon walls suggest the presence of intense bottom currents flowing parallel to canyon axis. A benthic habitat map of Hudson Canyon head was produced by integration of the different datasets. The distribution of habitats was primarily inferred from geophysical data characteristics. Furthermore habitat characteristics can be related to sedimentary and oceanographic processes acting on the seafloor. Comparison and refinement of bathymetric and backscatter imagery with ground truth data enabled validation of acoustic classification of the seafloor, allowing the definition of morpho-acoustic classes corresponding to as many habitats, and to extend the predictive results over larger areas.

  6. Importance of physiotherapy/nursing multidisciplinary integration about update newborn position in the neonatal intensive care unit

    Directory of Open Access Journals (Sweden)

    Vanessa da Silva Neves Moreira Arakaki

    Full Text Available AbstractIntroduction The high-risk newborns may require long periods of hospitalization until they reach clinical stability for hospital discharge. Avoiding babies to be in only one body position may be an effective way to cause respiratory and neuro-psycho-motor benefits, comfort and preventing pressure ulcers.Objectives This study investigated the impact of physiotherapy/nursing integration in update on body positioning of the newborn in the Neonatal Intensive Care Unit.Methods A questionnaire was administered to nurses and nursing technicians of the neonatal unit of Maternity School of UFRJ and nurses of the Advanced Course in Neonatal Nursing from the same institution. Two classes were taught by the physical therapist of the sector and the questions answered before and after these lessons. It was also a brief characterization of professional participants of the study. We used the Student's t test to compare the correct answers before (PRE and after (POST the classes, considering p < 0.05.Results There was a significant increase in the degree of knowledge of nurses and nursing technicians when compared the responses before (nurses: 68.8%; technicians: 70.1% and after classes (nurses: 78.4 %; technicians: 88.9%. The nurses were less than five years of graduated (45% and little time of professional experience in neonatology (60%. Forty-seven percent of technicians had less than five years of training and 82% had less than 10 years of experience.Conclusion The use of training by the nursing staff was significant, showing the importance of multidisciplinary approach and the integration of knowledge in the search for a humanized and effective care.

  7. Simulation Integrated Design for Logistics

    NARCIS (Netherlands)

    Veeke, H.P.M.

    2003-01-01

    The design of an innovative logistic system is a complex problem in the solution of which many disciplines are involved. Each discipline developed its own way of conceptual modeling for a logistic system based on a mono disciplinary perception. In essence this leads to a communication problem

  8. Semiconductors integrated circuit design for manufacturability

    CERN Document Server

    Balasinki, Artur

    2011-01-01

    Because of the continuous evolution of integrated circuit manufacturing (ICM) and design for manufacturability (DfM), most books on the subject are obsolete before they even go to press. That's why the field requires a reference that takes the focus off of numbers and concentrates more on larger economic concepts than on technical details. Semiconductors: Integrated Circuit Design for Manufacturability covers the gradual evolution of integrated circuit design (ICD) as a basis to propose strategies for improving return-on-investment (ROI) for ICD in manufacturing. Where most books put the spotl

  9. Managing Increasing Complexity in Undergraduate Digital Media Design Education: The Impact and Benefits of Multidisciplinary Collaboration

    Science.gov (United States)

    Fleischmann, Katja; Daniel, Ryan

    2013-01-01

    Increasing complexity is one of the most pertinent issues when discussing the role and future of design, designers and their education. The evolving nature of digital media technology has resulted in a profession in a state of flux with increasingly complex communication and design problems. The ability to collaborate and interact with other…

  10. Effectiveness of a multidisciplinary care program on recovery and return to work of patients after gynaecological surgery; design of a randomized controlled trial

    NARCIS (Netherlands)

    Vonk Noordegraaf, A.; Huirne, J.A.F.; Brölmann, H.A.M.; Emanuel, M.H.; van Kesteren, P.; Kleiverda, G.; Lips, J.P.; Mozes, A.; Thurkow, A.L.; van Mechelen, W.; Anema, J.R.

    2012-01-01

    Background: Return to work after gynaecological surgery takes much longer than expected, irrespective of the level of invasiveness. In order to empower patients in recovery and return to work, a multidisciplinary care program consisting of an e-health intervention and integrated care management

  11. Experiences of multidisciplinary development team members during user-centered design of telecare products and services: a qualitative study.

    Science.gov (United States)

    Vermeulen, Joan; Verwey, Renée; Hochstenbach, Laura M J; van der Weegen, Sanne; Man, Yan Ping; de Witte, Luc P

    2014-05-19

    User-centered design (UCD) methodologies can help take the needs and requirements of potential end-users into account during the development of innovative telecare products and services. Understanding how members of multidisciplinary development teams experience the UCD process might help to gain insight into factors that members with different backgrounds consider critical during the development of telecare products and services. The primary objective of this study was to explore how members of multidisciplinary development teams experienced the UCD process of telecare products and services. The secondary objective was to identify differences and similarities in the barriers and facilitators they experienced. Twenty-five members of multidisciplinary development teams of four Research and Development (R&D) projects participated in this study. The R&D projects aimed to develop telecare products and services that can support self-management in elderly people or patients with chronic conditions. Seven participants were representatives of end-users (elderly persons or patients with chronic conditions), three were professional end-users (geriatrician and nurses), five were engineers, four were managers (of R&D companies or engineering teams), and six were researchers. All participants were interviewed by a researcher who was not part of their own development team. The following topics were discussed during the interviews: (1) aim of the project, (2) role of the participant, (3) experiences during the development process, (4) points of improvement, and (5) what the project meant to the participant. Experiences of participants related to the following themes: (1) creating a development team, (2) expectations regarding responsibilities and roles, (3) translating user requirements into technical requirements, (4) technical challenges, (5) evaluation of developed products and services, and (6) valorization. Multidisciplinary team members from different backgrounds often

  12. Advanced Space Vehicle Design Taking into Account Multidisciplinary Couplings and Mixed Epistemic/Aleatory Uncertainties

    OpenAIRE

    Balesdent , Mathieu; Brevault , Loïc; Price , Nathaniel; Defoort , Sébastien; Le Riche , Rodolphe; Kim , Nam-Ho; Haftka , Raphael T.; Bérend , Nicolas

    2016-01-01

    International audience; Space vehicle design is a complex process involving numerous disciplines such as aerodynamics, structure, propulsion and trajectory. These disciplines are tightly coupled and may involve antagonistic objectives that require the use of specific methodologies in order to assess trade-offs between the disciplines and to obtain the global optimal configuration. Generally, there are two ways to handle the system design. On the one hand, the design may be considered from a d...

  13. Multi-fidelity and multi-disciplinary design optimization of supersonic business jets

    Science.gov (United States)

    Choi, Seongim

    Supersonic jets have been drawing great attention after the end of service for the Concorde was announced on April of 2003. It is believed, however, that civilian supersonic aircraft may make a viable return in the business jet market. This thesis focuses on the design optimization of feasible supersonic business jet configurations. Preliminary design techniques for mitigation of ground sonic boom are investigated while ensuring that all relevant disciplinary constraints are satisfied (including aerodynamic performance, propulsion, stability & control and structures.) In order to achieve reasonable confidence in the resulting designs, high-fidelity simulations are required, making the entire design process both expensive and complex. In order to minimize the computational cost, surrogate/approximate models are constructed using a hierarchy of different fidelity analysis tools including PASS, A502/Panair and Euler/NS codes. Direct search methods such as Genetic Algorithms (GAs) and a nonlinear SIMPLEX are employed to designs in searches of large and noisy design spaces. A local gradient-based search method can be combined with these global search methods for small modifications of candidate optimum designs. The Mesh Adaptive Direct Search (MADS) method can also be used to explore the design space using a solution-adaptive grid refinement approach. These hybrid approaches, both in search methodology and surrogate model construction, are shown to result in designs with reductions in sonic boom and improved aerodynamic performance.

  14. Three Course Connections: Integrated Event Design

    Science.gov (United States)

    Johnson, Corey W.; Pate, Joseph A.

    2013-01-01

    Integrated Event Design (IED) capitalizes on three distinct courses to achieve a blended course delivery: Event Management, Research and Evaluation (for undergraduate students), and Experiential Education (for graduate students). Through the use of an event management company metaphor that fully integrates the diverse curricular concepts, course…

  15. Integrated NTP Vehicle Radiation Design

    Science.gov (United States)

    Caffrey, Jarvis; Rodriquez, Mitchell

    2018-01-01

    The development of a nuclear thermal propulsion stage requires consideration for radiation emitted from the nuclear reactor core. Applying shielding mass is an effective mitigating solution, but a better alternative is to incorporate some mitigation strategies into the propulsion stage and crew habitat. In this way, the required additional mass is minimized and the mass that must be applied may in some cases be able to serve multiple purposes. Strategies for crew compartment shielding are discussed that reduce dose from both engine and cosmic sources, and in some cases may also serve to reduce life support risks by permitting abundant water reserves. Early consideration for integrated mitigation solutions in a crewed nuclear thermal propulsion (NTP) vehicle will enable reduced radiation burden from both cosmic and nuclear sources, improved thrust-to-weight ratio or payload capacity by reducing 'dead mass' of shielding, and generally support a more robust risk posture for a NTP-powered Mars mission by permitting shorter trip times and increased water reserves

  16. Integrated NTP Vehicle Radiation Design

    Science.gov (United States)

    Caffrey, Jarvis A.; Rodriquez, Mitchell A.

    2018-01-01

    The development of a nuclear thermal propulsion stage requires consideration for radiation emitted from the nuclear reactor core. Applying shielding mass is an effective mitigating solution, but a better alternative is to incorporate some mitigation strategies into the propulsion stage and crew habitat. In this way, the required additional mass is minimized and the mass that must be applied may in some cases be able to serve multiple purposes. Strategies for crew compartment shielding are discussed that reduce dose from both engine and cosmic sources, and in some cases may also serve to reduce life support risks by permitting abundant water reserves. Early consideration for integrated mitigation solutions in a crewed nuclear thermal propulsion (NTP) vehicle will enable reduced radiation burden from both cosmic and nuclear sources, improved thrust-to-weight ratio or payload capacity by reducing 'dead mass' of shielding, and generally support a more robust risk posture for a NTP-powered Mars mission by permitting shorter trip times and increased water reserves.

  17. An analog integrated circuit design laboratory

    OpenAIRE

    Mondragon-Torres, A.F.; Mayhugh, Jr.; Pineda de Gyvez, J.; Silva-Martinez, J.; Sanchez-Sinencio, E.

    2003-01-01

    We present the structure of an analog integrated circuit design laboratory to instruct at both, senior undergraduate and entry graduate levels. The teaching material includes: a laboratory manual with analog circuit design theory, pre-laboratory exercises and circuit design specifications; a reference web page with step by step instructions and examples; the use of mathematical tools for automation and analysis; and state of the art CAD design tools in use by industry. Upon completion of the ...

  18. Multi-objective and multidisciplinary design optimization of large sports building envelopes : A case study

    NARCIS (Netherlands)

    Yang, D.; Sun, Y.; Turrin, M.; von Buelow, P.; Paul, J.C.

    2015-01-01

    Currently, in the conceptual envelope design of sports facilities, multiple engineering performance feedbacks (e.g. daylight, energy and structural performance) are expected to assist architectural design decision-making. In general, it is known as Building Performance Optimization in the conceptual

  19. Sensitivity analysis and multidisciplinary optimization for aircraft design: Recent advances and results

    Science.gov (United States)

    Sobieszczanski-Sobieski, Jaroslaw

    1988-01-01

    Optimization by decomposition, complex system sensitivity analysis, and a rapid growth of disciplinary sensitivity analysis are some of the recent developments that hold promise of a quantum jump in the support engineers receive from computers in the quantitative aspects of design. Review of the salient points of these techniques is given and illustrated by examples from aircraft design as a process that combines the best of human intellect and computer power to manipulate data.

  20. Teaching Process Design through Integrated Process Synthesis

    Science.gov (United States)

    Metzger, Matthew J.; Glasser, Benjamin J.; Patel, Bilal; Hildebrandt, Diane; Glasser, David

    2012-01-01

    The design course is an integral part of chemical engineering education. A novel approach to the design course was recently introduced at the University of the Witwatersrand, Johannesburg, South Africa. The course aimed to introduce students to systematic tools and techniques for setting and evaluating performance targets for processes, as well as…

  1. Prototyping of Tangible Programming - An Iterative Approach to a Multidisciplinary Design Problem

    OpenAIRE

    Reime, Thov

    2015-01-01

    The Fibo Car is a game interface consisting of a kit of car parts. A virtual model of the assembled parts is generated on a computer and used in a physics engine based gameplay. This product vision is the source of this master s thesis task where the main goal was to develop a critical function prototype of the physical/virtual interface. The challenge of this task was to create a prototype that contained integrated technology from multiple engineering disciplines. After six weeks, a funct...

  2. EDITORIAL: Siberia Integrated Regional Study: multidisciplinary investigations of the dynamic relationship between the Siberian environment and global climate change

    Science.gov (United States)

    Gordov, E. P.; Vaganov, E. A.

    2010-03-01

    -Biosphere Program: integrated regional study of contemporary natural and climatic changes' is one of several funded interdisciplinary projects, and it serves to unite regional studies from 14 RAS and SB RAS institutes and 5 universities. In the course of this and similar national1 and international projects, ENVIROMIS and ENVIROMIS-2 (Environmental Observations, Modelling and Information Systems) was formed, which is the SIRS professional community comprising regional, national and international specialists dealing with Siberian environmental dynamics studies. Results of those and parallel projects were analyzed in by coordinated activities: 'Enviro-RISKS-Man-induced Environmental Risks: monitoring, management and remediation of man-made changes in Siberia' [12]. Currently, a new set of SB RAS integrated2 and international projects within the Asia-Pacific Network for Global Change Study (APN) and ISTC are under way. While a number of projects have been initiated and clustered under the SIRS umbrella and their results and data are distributed through the SIRS web portal (http://sirs.scert.ru/), the organizational SIRS infrastructure is inadequate. SIRS has neither SB RAS stable funding nor a dedicated Project Office. Both obstacles are a major concern for the SIRS governing body. Information-computational infrastructure development The SIRS informational-computational infrastructure, which is currently under extensive development, is designed to stimulate national and international cooperative Earth science investigations, easily exchange data and knowledge, coordinate activities, and optimize the usage of resources, services and applications [13]. The infrastructure is organized as a set of thematic, bilingual (Russian and English), internet-accessible informational-computational systems, the first of which is the scientific web portal ATMOS (http://atmos.iao.ru/). ATMOS is an integrated set of distributed topical websites, combining standard multimedia information with research

  3. The Integrated Computational Environment for Airbreathing Hypersonic Flight Vehicle Modeling and Design Evaluation, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — An integrated computational environment for multidisciplinary, physics-based simulation and analyses of airbreathing hypersonic flight vehicles will be developed....

  4. Integrating sustainability in interior design studio

    OpenAIRE

    Karslı, Umut Tuğlu

    2013-01-01

    Teaching methods on concept of sustainability are frequently searched in the interior architecture education. The purpose of this study is to propose a model for integrating sustainability in interior design studio. In this context, the first part of the research defines relationship between sustainability and interior architecture and determines sustainable interior design principles. In the second part, an interior design studio model is proposed and principles determined in the first part ...

  5. Combining Critical Reflection and Design Thinking to Develop Integrative Learners

    Science.gov (United States)

    Welsh, M. Ann; Dehler, Gordon E.

    2013-01-01

    In this article, we argue for advancing grounded curricula, which explicitly link theory and pedagogy, and executing them in authentic and multidisciplinary settings as a means to facilitate student growth into integrative learners. We describe the development of a student-centered learning experience that combines elements of critical management…

  6. Multi-Disciplinary Design Optimization of Hypersonic Air-Breathing Vehicle

    Science.gov (United States)

    Wu, Peng; Tang, Zhili; Sheng, Jianda

    2016-06-01

    A 2D hypersonic vehicle shape with an idealized scramjet is designed at a cruise regime: Mach number (Ma) = 8.0, Angle of attack (AOA) = 0 deg and altitude (H) = 30kms. Then a multi-objective design optimization of the 2D vehicle is carried out by using a Pareto Non-dominated Sorting Genetic Algorithm II (NSGA-II). In the optimization process, the flow around the air-breathing vehicle is simulated by inviscid Euler equations using FLUENT software and the combustion in the combustor is modeled by a methodology based on the well known combination effects of area-varying pipe flow and heat transfer pipe flow. Optimization results reveal tradeoffs among total pressure recovery coefficient of forebody, lift to drag ratio of vehicle, specific impulse of scramjet engine and the maximum temperature on the surface of vehicle.

  7. Multidisciplinary Simulation of Graphite-Composite and Cermet Fuel Elements for NTP Point of Departure Designs

    Science.gov (United States)

    Stewart, Mark E.; Schnitzler, Bruce G.

    2015-01-01

    This paper compares the expected performance of two Nuclear Thermal Propulsion fuel types. High fidelity, fluid/thermal/structural + neutronic simulations help predict the performance of graphite-composite and cermet fuel types from point of departure engine designs from the Nuclear Thermal Propulsion project. Materials and nuclear reactivity issues are reviewed for each fuel type. Thermal/structural simulations predict thermal stresses in the fuel and thermal expansion mis-match stresses in the coatings. Fluid/thermal/structural/neutronic simulations provide predictions for full fuel elements. Although NTP engines will utilize many existing chemical engine components and technologies, nuclear fuel elements are a less developed engine component and introduce design uncertainty. Consequently, these fuel element simulations provide important insights into NTP engine performance.

  8. Multidisciplinary Product Decomposition and Analysis Based on Design Structure Matrix Modeling

    DEFF Research Database (Denmark)

    Habib, Tufail

    2014-01-01

    Design structure matrix (DSM) modeling in complex system design supports to define physical and logical configuration of subsystems, components, and their relationships. This modeling includes product decomposition, identification of interfaces, and structure analysis to increase the architectural...... interactions across subsystems and components. For this purpose, Cambridge advanced modeler (CAM) software tool is used to develop the system matrix. The analysis of the product (printer) architecture includes clustering, partitioning as well as structure analysis of the system. The DSM analysis is helpful...... understanding of the system. Since product architecture has broad implications in relation to product life cycle issues, in this paper, mechatronic product is decomposed into subsystems and components, and then, DSM model is developed to examine the extent of modularity in the system and to manage multiple...

  9. Multidisciplinary Aerodynamic Design of a Rotor Blade for an Optimum Rotor Speed Helicopter

    Directory of Open Access Journals (Sweden)

    Jiayi Xie

    2017-06-01

    Full Text Available The aerodynamic design of rotor blades is challenging, and is crucial for the development of helicopter technology. Previous aerodynamic optimizations that focused only on limited design points find it difficult to balance flight performance across the entire flight envelope. This study develops a global optimum envelope (GOE method for determining blade parameters—blade twist, taper ratio, tip sweep—for optimum rotor speed helicopters (ORS-helicopters, balancing performance improvements in hover and various freestream velocities. The GOE method implements aerodynamic blade design by a bi-level optimization, composed of a global optimization step and a secondary optimization step. Power loss as a measure of rotor performance is chosen as the objective function, referred to as direct power loss (DPL in this study. A rotorcraft comprehensive code for trim simulation with a prescribed wake method is developed. With the application of the GOE method, a DPL reduction of as high as 16.7% can be achieved in hover, and 24% at high freestream velocity.

  10. Multidisciplinary Graduate Training in Social Research Methodology and Computer-Assisted Qualitative Data Analysis: A Hands-On/Hands-Off Course Design

    Science.gov (United States)

    Bourque, Claude Julie; Bourdon, Sylvain

    2017-01-01

    Drawing on the experience of training graduate students and researchers in qualitative and mixed-methods analysis since the mid-1990s, the authors reflect on the evolution of a multidisciplinary graduate course developed in a Canadian university since 2007. The hands-on/hands-off course design based on the use of NVivo was developed in parallel…

  11. Behavioural design: A process for integrating behaviour change and design

    DEFF Research Database (Denmark)

    Cash, Philip; Hartlev, Charlotte Gram; Durazo, Christine Boysen

    2017-01-01

    Nudge, persuasion, and the influencing of human behaviour through design are increasingly important topics in design research and in the wider public consciousness. However, current theoretical approaches to behaviour change have yet to be operationalized this in design process support....... Specifically, there are few empirically grounded processes supporting designers in realising behaviour change projects. In response to this, 20 design projects from a case company are analysed in order to distil a core process for behavioural design. Results show a number of process stages and activities...... associated with project success, pointing to a new perspective on the traditional design process, and allowing designers to integrate key insights from behaviour change theory. Using this foundation we propose the Behavioural Design process....

  12. Multidisciplinary treatment

    International Nuclear Information System (INIS)

    Hayabuchi, Naofumi; Jingu, Kenichi; Matsuura, Keiichi

    1985-01-01

    Multidisciplinary treatment for malignant lymphoma is reported in terms of indication, current status, and outcome of this approach to Hodgkin's disease (HD) and non-Hodgkin's lymphomas (NLH). HD is considered to be most successfully managed with multidisciplinary treatment. Success of treatment of HD in European countries and the US, which has resulted from accurate staging of HD and developments in radiotherapy and chemotherapy, is reviewed in the literature. Problems in the treatment of HD in Japan are presented. A treatment policy for NHL is discussed according to the original site, i.e. lymph nodes, Waldeyer's ring or other sites of tumor involvement. (Namekawa, K.)

  13. Power management techniques for integrated circuit design

    CERN Document Server

    Chen, Ke-Horng

    2016-01-01

    This book begins with the premise that energy demands are directing scientists towards ever-greener methods of power management, so highly integrated power control ICs (integrated chip/circuit) are increasingly in demand for further reducing power consumption. * A timely and comprehensive reference guide for IC designers dealing with the increasingly widespread demand for integrated low power management * Includes new topics such as LED lighting, fast transient response, DVS-tracking and design with advanced technology nodes * Leading author (Chen) is an active and renowned contributor to the power management IC design field, and has extensive industry experience * Accompanying website includes presentation files with book illustrations, lecture notes, simulation circuits, solution manuals, instructors manuals, and program downloads.

  14. Integrated plant information technology design support functionality

    International Nuclear Information System (INIS)

    Kim, Yeon Seung; Kim, Dae Jin; Barber, P. W.; Goland, D.

    1996-06-01

    This technical report was written as a result of Integrated Plant Information System (IPIS) feasibility study on CANDU 9 project which had been carried out from January, 1994 to March, 1994 at AECL (Atomic Energy Canada Limited) in Canada. From 1987, AECL had done endeavour to change engineering work process from paper based work process to computer based work process through CANDU 3 project. Even though AECL had a lot of good results form computerizing the Process Engineering, Instrumentation Control and Electrical Engineering, Mechanical Engineering, Computer Aided Design and Drafting, and Document Management System, but there remains the problem of information isolation and integration. On this feasibility study, IPIS design support functionality guideline was suggested by evaluating current AECL CAE tools, analyzing computer aided engineering task and work flow, investigating request for implementing integrated computer aided engineering and describing Korean request for future CANDU design including CANDU 9. 6 figs. (Author)

  15. Integrated plant information technology design support functionality

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Yeon Seung; Kim, Dae Jin [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of); Barber, P W; Goland, D [Atomic Energy Canada Ltd., (Canada)

    1996-06-01

    This technical report was written as a result of Integrated Plant Information System (IPIS) feasibility study on CANDU 9 project which had been carried out from January, 1994 to March, 1994 at AECL (Atomic Energy Canada Limited) in Canada. From 1987, AECL had done endeavour to change engineering work process from paper based work process to computer based work process through CANDU 3 project. Even though AECL had a lot of good results form computerizing the Process Engineering, Instrumentation Control and Electrical Engineering, Mechanical Engineering, Computer Aided Design and Drafting, and Document Management System, but there remains the problem of information isolation and integration. On this feasibility study, IPIS design support functionality guideline was suggested by evaluating current AECL CAE tools, analyzing computer aided engineering task and work flow, investigating request for implementing integrated computer aided engineering and describing Korean request for future CANDU design including CANDU 9. 6 figs. (Author).

  16. Multidisciplinary Design Optimization for Glass-Fiber Epoxy-Matrix Composite 5 MW Horizontal-Axis Wind-Turbine Blades

    Science.gov (United States)

    Grujicic, M.; Arakere, G.; Pandurangan, B.; Sellappan, V.; Vallejo, A.; Ozen, M.

    2010-11-01

    A multi-disciplinary design-optimization procedure has been introduced and used for the development of cost-effective glass-fiber reinforced epoxy-matrix composite 5 MW horizontal-axis wind-turbine (HAWT) blades. The turbine-blade cost-effectiveness has been defined using the cost of energy (CoE), i.e., a ratio of the three-blade HAWT rotor development/fabrication cost and the associated annual energy production. To assess the annual energy production as a function of the blade design and operating conditions, an aerodynamics-based computational analysis had to be employed. As far as the turbine blade cost is concerned, it is assessed for a given aerodynamic design by separately computing the blade mass and the associated blade-mass/size-dependent production cost. For each aerodynamic design analyzed, a structural finite element-based and a post-processing life-cycle assessment analyses were employed in order to determine a minimal blade mass which ensures that the functional requirements pertaining to the quasi-static strength of the blade, fatigue-controlled blade durability and blade stiffness are satisfied. To determine the turbine-blade production cost (for the currently prevailing fabrication process, the wet lay-up) available data regarding the industry manufacturing experience were combined with the attendant blade mass, surface area, and the duration of the assumed production run. The work clearly revealed the challenges associated with simultaneously satisfying the strength, durability and stiffness requirements while maintaining a high level of wind-energy capture efficiency and a lower production cost.

  17. Design of analog integrated circuits and systems

    CERN Document Server

    Laker, Kenneth R

    1994-01-01

    This text is designed for senior or graduate level courses in analog integrated circuits or design of analog integrated circuits. This book combines consideration of CMOS and bipolar circuits into a unified treatment. Also included are CMOS-bipolar circuits made possible by BiCMOS technology. The text progresses from MOS and bipolar device modelling to simple one and two transistor building block circuits. The final two chapters present a unified coverage of sample-data and continuous-time signal processing systems.

  18. Integrating Anatomy Training into Radiation Oncology Residency: Considerations for Developing a Multidisciplinary, Interactive Learning Module for Adult Learners

    Science.gov (United States)

    Labranche, Leah; Johnson, Marjorie; Palma, David; D'Souza, Leah; Jaswal, Jasbir

    2015-01-01

    Radiation oncologists require an in-depth understanding of anatomical relationships for modern clinical practice, although most do not receive formal anatomy training during residency. To fulfill the need for instruction in relevant anatomy, a series of four multidisciplinary, interactive learning modules were developed for a cohort of radiation…

  19. SUBSURFACE REPOSITORY INTEGRATED CONTROL SYSTEM DESIGN

    International Nuclear Information System (INIS)

    Randle, D.C.

    2000-01-01

    The primary purpose of this document is to develop a preliminary high-level functional and physical control system architecture for the potential repository at Yucca Mountain. This document outlines an overall control system concept that encompasses and integrates the many diverse process and communication systems being developed for the subsurface repository design. This document presents integrated design concepts for monitoring and controlling the diverse set of subsurface operations. The Subsurface Repository Integrated Control System design will be composed of a series of diverse process systems and communication networks. The subsurface repository design contains many systems related to instrumentation and control (I andC) for both repository development and waste emplacement operations. These systems include waste emplacement, waste retrieval, ventilation, radiological and air monitoring, rail transportation, construction development, utility systems (electrical, lighting, water, compressed air, etc.), fire protection, backfill emplacement, and performance confirmation. Each of these systems involves some level of I andC and will typically be integrated over a data communications network throughout the subsurface facility. The subsurface I andC systems will also interface with multiple surface-based systems such as site operations, rail transportation, security and safeguards, and electrical/piped utilities. In addition to the I andC systems, the subsurface repository design also contains systems related to voice and video communications. The components for each of these systems will be distributed and linked over voice and video communication networks throughout the subsurface facility. The scope and primary objectives of this design analysis are to: (1) Identify preliminary system-level functions and interfaces (Section 6.2). (2) Examine the overall system complexity and determine how and on what levels the engineered process systems will be monitored

  20. Integrated design strategy for product life-cycle management

    Science.gov (United States)

    Johnson, G. Patrick

    2001-02-01

    Two major trends suggest new considerations for environmentally conscious manufacturing (ECM) -- the continuation of dematerialization and the growing trend toward goods becoming services. A diversity of existing research could be integrated around those trends in ways that can enhance ECM. Major research-based achievements in information, computation, and communications systems, sophisticated and inexpensive sensing capabilities, highly automated and precise manufacturing technologies, and new materials continue to drive the phenomenon of dematerialization - the reduction of the material and energy content of per capita GDP. Knowledge is also growing about the sociology, economics, mathematics, management and organization of complex socio-economic systems. And that has driven a trend towards goods evolving into services. But even with these significant trends, the value of material, energy, information and human resources incorporated into the manufacture, use and disposal of modern products and services often far exceeds the benefits realized. Multi-disciplinary research integrating these drivers with advances in ECM concepts could be the basis for a new strategy of production. It is argued that a strategy of integrating information resources with physical and human resources over product life cycles, together with considering products as streams of service over time, could lead to significant economic payoff. That strategy leads to an overall design concept to minimize costs of all resources over the product life cycle to more fully capture benefits of all resources incorporated into modern products. It is possible by including life cycle monitoring, periodic component replacement, re-manufacture, salvage and human factor skill enhancement into initial design.

  1. Design Creativity: Future Directions for Integrated Visualisation

    Directory of Open Access Journals (Sweden)

    Jack Steven Goulding

    2015-11-01

    Full Text Available The Architecture, Engineering and Construction (AEC sectors are facing unprecedented challenges, not just with increased complexity of projects per se, but design-related integration. This requires stakeholders to radically re-think their existing business models (and thinking that underpins them, but also the technological challenges and skills required to deliver these projects. Whilst opponents will no doubt cite that this is nothing new as the sector as a whole has always had to respond to change; the counter to this is that design ‘creativity’ is now much more dependent on integration from day one. Given this, collaborative processes embedded in Building Information Modelling (BIM models have been proffered as a panacea solution to embrace this change and deliver streamlined integration. The veracity of design teams’ “project data” is increasingly becoming paramount - not only for the coordination of design, processes, engineering services, fabrication, construction, and maintenance; but more importantly, facilitate ‘true’ project integration and interchange – the actualisation of which will require firm consensus and commitment. This Special Issue envisions some of these issues, challenges and opportunities (from a future landscape perspective, by highlighting a raft of concomitant factors, which include: technological challenges, design visualisation and integration, future digital tools, new and anticipated operating environments, and training requirements needed to deliver these aspirations. A fundamental part of this Special Issue’s ‘call’ was to capture best practice in order to demonstrate how design, visualisation and delivery processes (and technologies affect the finished product viz: design outcome, design procedures, production methodologies and construction implementation. In this respect, the use of virtual environments are now particularly effective at supporting the design and delivery processes. In

  2. High-frequency analog integrated circuit design

    CERN Document Server

    1995-01-01

    To learn more about designing analog integrated circuits (ICs) at microwave frequencies using GaAs materials, turn to this text and reference. It addresses GaAs MESFET-based IC processing. Describes the newfound ability to apply silicon analog design techniques to reliable GaAs materials and devices which, until now, was only available through technical papers scattered throughout hundred of articles in dozens of professional journals.

  3. Integrated computer aided design simulation and manufacture

    OpenAIRE

    Diko, Faek

    1989-01-01

    Computer Aided Design (CAD) and Computer Aided Manufacture (CAM) have been investigated and developed since twenty years as standalone systems. A large number of very powerful but independent packages have been developed for Computer Aided Design,Aanlysis and Manufacture. However, in most cases these packages have poor facility for communicating with other packages. Recently attempts have been made to develop integrated CAD/CAM systems and many software companies a...

  4. Integrated Energy Design of the Building Envelope

    DEFF Research Database (Denmark)

    Nielsen, Martin Vraa

    This thesis describes the outcome of the PhD project Integrated energy design of the building envelope carried out through a combination of scientific dissemination reported through peer-reviewed journals and a wide range of affiliated projects involved in at an architectural firm. The research...

  5. A new integrated microwave SQUID circuit design

    International Nuclear Information System (INIS)

    Erne, S.N.; Finnegan, T.F.

    1980-01-01

    In this paper we consider the design and operation of a planar thin-film rf-SQUID circuit which can be realized via microwave-integrated-circuit (MIC) techniques and which differs substantially from pervious microwave SQUID configurations involving either mechanical point-contact or cylindrical thin-film micro-bridge geometries. (orig.)

  6. Integrated analysis of wind turbines - The impact of power systems on wind turbine design

    DEFF Research Database (Denmark)

    Barahona Garzón, Braulio

    Megawatt-size wind turbines nowadays operate in very complex environmental conditions, and increasingly demanding power system requirements. Pursuing a cost-effective and reliable wind turbine design is a multidisciplinary task. However nowadays, wind turbine design and research areas...... conditions that stem from disturbances in the power system. An integrated simulation environment, wind turbine models, and power system models are developed in order to take an integral perspective that considers the most important aeroelastic, structural, electrical, and control dynamics. Applications...... of the integrated simulation environment are presented. The analysis of an asynchronous machine, and numerical simulations of a fixedspeed wind turbine in the integrated simulation environment, demonstrate the effects on structural loads of including the generator rotor fluxes dynamics in aeroelastic studies. Power...

  7. Design Considerations for Proposed Fermilab Integrable RCS

    Energy Technology Data Exchange (ETDEWEB)

    Eldred, Jeffrey [Fermilab; Valishev, Alexander

    2017-03-02

    Integrable optics is an innovation in particle accelerator design that provides strong nonlinear focusing while avoiding parametric resonances. One promising application of integrable optics is to overcome the traditional limits on accelerator intensity imposed by betatron tune-spread and collective instabilities. The efficacy of high-intensity integrable accelerators will be undergo comprehensive testing over the next several years at the Fermilab Integrable Optics Test Accelerator (IOTA) and the University of Maryland Electron Ring (UMER). We propose an integrable Rapid-Cycling Synchrotron (iRCS) as a replacement for the Fermilab Booster to achieve multi-MW beam power for the Fermilab high-energy neutrino program. We provide a overview of the machine parameters and discuss an approach to lattice optimization. Integrable optics requires arcs with integer-pi phase advance followed by drifts with matched beta functions. We provide an example integrable lattice with features of a modern RCS - long dispersion-free drifts, low momentum compaction, superperiodicity, chromaticity correction, separate-function magnets, and bounded beta functions.

  8. Three-dimensional integrated circuit design

    CERN Document Server

    Xie, Yuan; Sapatnekar, Sachin S

    2009-01-01

    This book presents an overview of the field of 3D IC design, with an emphasis on electronic design automation (EDA) tools and algorithms that can enable the adoption of 3D ICs, and the architectural implementation and potential for future 3D system design. The aim of this book is to provide the reader with a complete understanding of: the promise of 3D ICs in building novel systems that enable the chip industry to continue along the path of performance scaling, the state of the art in fabrication technologies for 3D integration, the most prominent 3D-specific EDA challenges, along with solutio

  9. Integrated Design Engineering Analysis (IDEA) Environment Automated Generation of Structured CFD Grids using Topology Methods

    Science.gov (United States)

    Kamhawi, Hilmi N.

    2012-01-01

    This report documents the work performed from March 2010 to March 2012. The Integrated Design and Engineering Analysis (IDEA) environment is a collaborative environment based on an object-oriented, multidisciplinary, distributed framework using the Adaptive Modeling Language (AML) as a framework and supporting the configuration design and parametric CFD grid generation. This report will focus on describing the work in the area of parametric CFD grid generation using novel concepts for defining the interaction between the mesh topology and the geometry in such a way as to separate the mesh topology from the geometric topology while maintaining the link between the mesh topology and the actual geometry.

  10. Development, implementation, and evaluation of an integrated multidisciplinary Objective Structured Clinical Examination (OSCE) in primary health care settings within limited resources.

    Science.gov (United States)

    Abdelaziz, Adel; Hany, Mohamed; Atwa, Hani; Talaat, Wagdy; Hosny, Somaya

    2016-01-01

    In ordinary circumstances, objective structured clinical examination (OSCE) is a resource-intensive assessment method. In case of developing and implementing multidisciplinary OSCE, there is no doubt that the cost will be greater. Through this study a research project was conducted to develop, implement and evaluate a multidisciplinary OSCE model within limited resources. This research project went through the steps of blueprinting, station writing, resources reallocation, implementation and finally evaluation. The developed model was implemented in the Primary Health Care (PHC) program which is one of the pillars of the Community-Based undergraduate curriculum of the Faculty of Medicine, Suez Canal University (FOM-SCU). Data for evaluation of the implemented OSCE model were derived from two resources. First, feedback of the students and assessors through self-administered questionnaires was obtained. Second, evaluation of the OSCE psychometrics was done. The deliverables of this research project included a set of validated integrated multi-disciplinary and low cost OSCE stations with an estimated reliability index of 0.6. After having this experience, we have a critical mass of faculty members trained on blueprinting and station writing and a group of trained assessors, facilitators and role players. Also there is a state of awareness among students on how to proceed in this type of OSCE which renders future implementation more feasible.

  11. SUBSURFACE REPOSITORY INTEGRATED CONTROL SYSTEM DESIGN

    International Nuclear Information System (INIS)

    C.J. Fernado

    1998-01-01

    The purpose of this document is to develop preliminary high-level functional and physical control system architectures for the proposed subsurface repository at Yucca Mountain. This document outlines overall control system concepts that encompass and integrate the many diverse systems being considered for use within the subsurface repository. This document presents integrated design concepts for monitoring and controlling the diverse set of subsurface operations. The subsurface repository design will be composed of a series of diverse systems that will be integrated to accomplish a set of overall functions and objectives. The subsurface repository contains several Instrumentation and Control (I andC) related systems including: waste emplacement systems, ventilation systems, communication systems, radiation monitoring systems, rail transportation systems, ground control monitoring systems, utility monitoring systems (electrical, lighting, water, compressed air, etc.), fire detection and protection systems, retrieval systems, and performance confirmation systems. Each of these systems involve some level of I andC and will typically be integrated over a data communication network. The subsurface I andC systems will also integrate with multiple surface-based site-wide systems such as emergency response, health physics, security and safeguards, communications, utilities and others. The scope and primary objectives of this analysis are to: (1) Identify preliminary system level functions and interface needs (Presented in the functional diagrams in Section 7.2). (2) Examine the overall system complexity and determine how and on what levels these control systems will be controlled and integrated (Presented in Section 7.2). (3) Develop a preliminary subsurface facility-wide design for an overall control system architecture, and depict this design by a series of control system functional block diagrams (Presented in Section 7.2). (4) Develop a series of physical architectures

  12. SUBSURFACE REPOSITORY INTEGRATED CONTROL SYSTEM DESIGN

    Energy Technology Data Exchange (ETDEWEB)

    C.J. Fernado

    1998-09-17

    The purpose of this document is to develop preliminary high-level functional and physical control system architectures for the proposed subsurface repository at Yucca Mountain. This document outlines overall control system concepts that encompass and integrate the many diverse systems being considered for use within the subsurface repository. This document presents integrated design concepts for monitoring and controlling the diverse set of subsurface operations. The subsurface repository design will be composed of a series of diverse systems that will be integrated to accomplish a set of overall functions and objectives. The subsurface repository contains several Instrumentation and Control (I&C) related systems including: waste emplacement systems, ventilation systems, communication systems, radiation monitoring systems, rail transportation systems, ground control monitoring systems, utility monitoring systems (electrical, lighting, water, compressed air, etc.), fire detection and protection systems, retrieval systems, and performance confirmation systems. Each of these systems involve some level of I&C and will typically be integrated over a data communication network. The subsurface I&C systems will also integrate with multiple surface-based site-wide systems such as emergency response, health physics, security and safeguards, communications, utilities and others. The scope and primary objectives of this analysis are to: (1) Identify preliminary system level functions and interface needs (Presented in the functional diagrams in Section 7.2). (2) Examine the overall system complexity and determine how and on what levels these control systems will be controlled and integrated (Presented in Section 7.2). (3) Develop a preliminary subsurface facility-wide design for an overall control system architecture, and depict this design by a series of control system functional block diagrams (Presented in Section 7.2). (4) Develop a series of physical architectures that

  13. Learning robots : teaching design students in integrating intelligence

    NARCIS (Netherlands)

    Barakova, E.I.; Hu, J.

    2011-01-01

    The present day society requires specialists with multidisciplinary knowledge and skills. We discuss the possibilities to educate professionals that design intelligent products and systems as a result of a competency based education. In particular this paper features a teaching method that makes the

  14. Approaches to Integrated Building Design Environments

    DEFF Research Database (Denmark)

    Bagger-Petersen, Susanne C; Andersen, Tom

    1996-01-01

    This report discusses functional requirements and specification which needs to be defined and fulfilled to initiate development of an integrated building design environment. The purpose is to outline specifications for further discussion and development. The report documents the first phase...... in an ongoing project at the Technical University of Denmark. The overall project objective is to provide a theoretically well-founded prototype of an integrated IT-system which can serve as a device of feedback from practice and as a test-bed for the developed concept and architecture....

  15. Evolutionary optimization and game strategies for advanced multi-disciplinary design applications to aeronautics and UAV design

    CERN Document Server

    Periaux, Jacques; Lee, Dong Seop Chris

    2015-01-01

    Many complex aeronautical design problems can be formulated with efficient multi-objective evolutionary optimization methods and game strategies. This book describes the role of advanced innovative evolution tools in the solution, or the set of solutions of single or multi disciplinary optimization. These tools use the concept of multi-population, asynchronous parallelization and hierarchical topology which allows different models including precise, intermediate and approximate models with each node belonging to the different hierarchical layer handled by a different Evolutionary Algorithm. The efficiency of evolutionary algorithms for both single and multi-objective optimization problems are significantly improved by the coupling of EAs with games and in particular by a new dynamic methodology named “Hybridized Nash-Pareto games”. Multi objective Optimization techniques and robust design problems taking into account uncertainties are introduced and explained in detail. Several applications dealing with c...

  16. Nuclear integrated database and design advancement system

    International Nuclear Information System (INIS)

    Ha, Jae Joo; Jeong, Kwang Sub; Kim, Seung Hwan; Choi, Sun Young.

    1997-01-01

    The objective of NuIDEAS is to computerize design processes through an integrated database by eliminating the current work style of delivering hardcopy documents and drawings. The major research contents of NuIDEAS are the advancement of design processes by computerization, the establishment of design database and 3 dimensional visualization of design data. KSNP (Korea Standard Nuclear Power Plant) is the target of legacy database and 3 dimensional model, so that can be utilized in the next plant design. In the first year, the blueprint of NuIDEAS is proposed, and its prototype is developed by applying the rapidly revolutionizing computer technology. The major results of the first year research were to establish the architecture of the integrated database ensuring data consistency, and to build design database of reactor coolant system and heavy components. Also various softwares were developed to search, share and utilize the data through networks, and the detailed 3 dimensional CAD models of nuclear fuel and heavy components were constructed, and walk-through simulation using the models are developed. This report contains the major additions and modifications to the object oriented database and associated program, using methods and Javascript.. (author). 36 refs., 1 tab., 32 figs

  17. Go4it; study design of a randomised controlled trial and economic evaluation of a multidisciplinary group intervention for obese adolescents for prevention of diabetes mellitus type 2

    Directory of Open Access Journals (Sweden)

    Weijs Peter JM

    2008-12-01

    Full Text Available Abstract Background In the Netherlands, the first adolescents with diabetes mellitus type 2 as a result of obesity have recently been diagnosed. Therefore, it is very important that programs aiming at the prevention of type 2 diabetes of obese adolescents are developed and evaluated. Methods Go4it is a multidisciplinary group treatment that focuses on: 1 increasing awareness of the current dietary and physical activity behaviour (i.e. energy balance behaviour, 2 improving diet, 3 decreasing sedentary behaviour, 4 increasing levels of physical activity, and 5 coping with difficult situations. Go4it consists of 7 sessions with an interval of 2–3 weeks. The effectiveness of the multidisciplinary group treatment compared with usual care (i.e. referral to a dietician was evaluated in a randomised controlled trial. We examined effects on BMI(sds, body composition, energy expenditure, glucose tolerance and insulin resistance (primary outcome measure, as well as dietary and physical activity behaviour and quality of life. An economic evaluation from a societal perspective was conducted alongside the randomised trial to evaluate the cost-effectiveness of the multidisciplinary treatment program vs. usual care. Discussion In this paper we described a multidisciplinary treatment program (Go4it for obese adolescents and the design of a randomised controlled trial and economic evaluation to evaluate its effectiveness and cost-effectiveness. Trial registration Netherlands Trial Register (ISRCTN27626398.

  18. AP1000 design and construction integration

    International Nuclear Information System (INIS)

    Winters, James W.; Clelland, Jill A.

    2004-01-01

    Construction costs of commercial nuclear generating plants must be reduced in order to expand the future use of nuclear energy. Two of the drivers of plant construction costs are the cost of financing during the construction duration and the substantial amount of skilled craft labor hours needed on site during construction. The application of information technology (IT) has been used to understand and reduce both of these drivers by establishing parallel construction paths using modules and integrating construction sequence review into the design process. In a program sponsored by EPRI, Westinghouse has modeled the construction of AP1000 in '4D' to show its viability, to improve its logic, to improve the plant design for constructibility and overall to reduce time and risk in the construction schedule. The design of most of AP1000 was constrained to be a duplicate of AP600 except where components required expansion for the higher power level. As a result, the construction schedule for AP1000 is as mature and as robust as that for AP600. Two areas important to the construction of AP1000 did require some design work because they could not remain the same as AP1000. First, the turbine building had to be redesigned to accommodate the larger turbine and its support systems. Again, as much of the AP600 design and philosophy as possible was retained. The building required enlargement and the basemat, foundations, steel structure and structural modules required modification. As concrete, steel, and equipment were defined by the designers, they were matched to the original AP600 turbine building schedule. This forced designers to assemble files to be consistent with building assembly activities and to think about constructibility as they defined the final design. Second, the reinforcement structure within the concrete under and supporting the containment vessel required detail design. Westinghouse was fortunate to have the constructor Obayashi of Japan recommend a detailed

  19. Towards the Successful Integration of Design Thinking in Industrial Design Education

    Science.gov (United States)

    Mubin, Omar; Novoa, Mauricio; Al Mahmud, Abdullah

    2016-01-01

    This paper narrates a case study on design thinking based education work in an industrial design honours program. Student projects were developed in a multi-disciplinary setting across a Computing and Engineering faculty that allowed promoting technologically and user driven innovation strategies. A renewed culture and environment for Industrial…

  20. Multi-disciplinary decision making in general practice.

    Science.gov (United States)

    Kirby, Ann; Murphy, Aileen; Bradley, Colin

    2018-04-09

    Purpose Internationally, healthcare systems are moving towards delivering care in an integrated manner which advocates a multi-disciplinary approach to decision making. Such an approach is formally encouraged in the management of Atrial Fibrillation patients through the European Society of Cardiology guidelines. Since the emergence of new oral anticoagulants switching between oral anticoagulants (OACs) has become prevalent. This case study considers the role of multi-disciplinary decision making, given the complex nature of the agents. The purpose of this paper is to explore Irish General Practitioners' (GPs) experience of switching between all OACs for Arial Fibrillation (AF) patients; prevalence of multi-disciplinary decision making in OAC switching decisions and seeks to determine the GP characteristics that appear to influence the likelihood of multi-disciplinary decision making. Design/methodology/approach A probit model is used to determine the factors influencing multi-disciplinary decision making and a multinomial logit is used to examine the factors influencing who is involved in the multi-disciplinary decisions. Findings Results reveal that while some multi-disciplinary decision-making is occurring (64 per cent), it is not standard practice despite international guidelines on integrated care. Moreover, there is a lack of patient participation in the decision-making process. Female GPs and GPs who have initiated prescriptions for OACs are more likely to engage in multi-disciplinary decision-making surrounding switching OACs amongst AF patients. GPs with training practices were less likely to engage with cardiac consultants and those in urban areas were more likely to engage with other (non-cardiac) consultants. Originality/value For optimal decision making under uncertainty multi-disciplinary decision-making is needed to make a more informed judgement and to improve treatment decisions and reduce the opportunity cost of making the wrong decision.

  1. Simulation of integrated beam experiment designs

    International Nuclear Information System (INIS)

    Grote, D.P.; Sharp, W.M.

    2004-01-01

    Simulation of designs of an Integrated Beam Experiment (IBX) class accelerator have been carried out. These simulations are an important tool for validating such designs. Issues such as envelope mismatch and emittance growth can be examined in a self-consistent manner, including the details of injection, accelerator transitions, long-term transport, and longitudinal compression. The simulations are three-dimensional and time-dependent, and begin at the source. They continue up through the end of the acceleration region, at which point the data is passed on to a separate simulation of the drift compression. Results are be presented

  2. An integral design of NHR-200

    International Nuclear Information System (INIS)

    Xue Dazhi; Li Jicai; Chang Dafeng

    1997-01-01

    Nuclear heating application has received a wide attention in China due to the favourable economic and environmental aspects. The Nuclear Heating Plant NHR-200 is seen to provide the required energy for district heating, industrial processes and seawater desalination for many sites in China and possibly abroad. The paper summarizes the technical description of the plant and give its main characteristics related to the integral design approach. (author)

  3. TOWARDS TOTAL INTEGRATION IN DESIGN STUDIO

    Directory of Open Access Journals (Sweden)

    Shireesh A Deshpande

    2010-07-01

    Full Text Available Transmission of knowledge has been defined as “bringing the right knowledge by the right route at the right time to the right places.” In this context there is need to analyze the various pedagogical shifts associated with the decisive process of transmission and transaction of knowledge in design studio. Critical understanding of the importance of tangential knowledge and its integration within the design studio, leading to a comprehensive whole, is a significant aspect to be properly evolved and nourished in the studio. It can be argued that knowledge is not a substitute for architectural imagination but inadequate knowledge would handicap the general level of design. Being satisfied to manipulate formal configurations does not provide insights into the human experience. If the different types of knowledge that architecture requires are ignored, the profession will lose its credibility in the eyes of society. With the body of knowledge expanding diversely with the escalating wants of the user, and to further sustain the built environment with further progression, it’s quite certain to have an innovative design process that has a feel of antecedents yet is nourished by rationalism. Architectural Design is to an extent the yield of a creative process brought out through a refined approach, skill, and dexterity to suit the purpose. The assessors, the jury, or the teacher has created an aura of mystique around good design, without much explaining what good design is. Architectural education involves application of a theory of knowledge – what is known and how it is to be known. Nothing is taught unless it is learnt (Bono. Does the key to these issues lie in shifting from conventional mode to Total Integration Mode of Education?

  4. Integrated energy design of the building envelope

    Energy Technology Data Exchange (ETDEWEB)

    Vraa Nielsen, M.

    2012-07-01

    This thesis describes the outcome of the PhD project Integrated energy design of the building envelope carried out through a combination of scientific dissemination reported through peer-reviewed journals and a wide range of affiliated projects involved in at an architectural firm. The research project analysed how the implementation of technical knowledge early in the building design process can quantify the effect of a building's facades on its energy efficiency and indoor climate and thereby facilitate a more qualified design development. The project was structured in the following way: 1) the importance of integrating knowledge in the early stages of design, and how it can be done; 2) understanding the facade's typology; and 3) the complex notion of comfort. The project touched not only on the technical capabilities and requirements governing facade design, but also the process by which it takes place. This was done by applying the methodology of Integrated Energy Design (IED) and analysing its applicability in the design of facades. A major part of the project was an actual engagement in the architectural process to test out incorporating a consciousness about energy and comfort as part of a more holistic performance evaluation. The research project illustrates the great potential in taking passive properties into account through a geometrical optimisation inherent in the development of the architectural concept. It demonstrates that integration of technical knowledge at the early stages of design not only can qualify the geometrical processing, but also facilitate the design development of the facade. Thereby a more holistic performance optimisation can be obtained through parameters such as overall facade geometry and orientation, functional organisation, room height and depth, facade layout, window geometry and transparency, design of the window aperture, etc. Through the wide range of affiliated project involved in at the architectural firm over

  5. "Usability of data integration and visualization software for multidisciplinary pediatric intensive care: a human factors approach to assessing technology".

    Science.gov (United States)

    Lin, Ying Ling; Guerguerian, Anne-Marie; Tomasi, Jessica; Laussen, Peter; Trbovich, Patricia

    2017-08-14

    Intensive care clinicians use several sources of data in order to inform decision-making. We set out to evaluate a new interactive data integration platform called T3™ made available for pediatric intensive care. Three primary functions are supported: tracking of physiologic signals, displaying trajectory, and triggering decisions, by highlighting data or estimating risk of patient instability. We designed a human factors study to identify interface usability issues, to measure ease of use, and to describe interface features that may enable or hinder clinical tasks. Twenty-two participants, consisting of bedside intensive care physicians, nurses, and respiratory therapists, tested the T3™ interface in a simulation laboratory setting. Twenty tasks were performed with a true-to-setting, fully functional, prototype, populated with physiological and therapeutic intervention patient data. Primary data visualization was time series and secondary visualizations were: 1) shading out-of-target values, 2) mini-trends with exaggerated maxima and minima (sparklines), and 3) bar graph of a 16-parameter indicator. Task completion was video recorded and assessed using a use error rating scale. Usability issues were classified in the context of task and type of clinician. A severity rating scale was used to rate potential clinical impact of usability issues. Time series supported tracking a single parameter but partially supported determining patient trajectory using multiple parameters. Visual pattern overload was observed with multiple parameter data streams. Automated data processing using shading and sparklines was often ignored but the 16-parameter data reduction algorithm, displayed as a persistent bar graph, was visually intuitive. However, by selecting or automatically processing data, triggering aids distorted the raw data that clinicians use regularly. Consequently, clinicians could not rely on new data representations because they did not know how they were

  6. Inviscid/Boundary-Layer Aeroheating Approach for Integrated Vehicle Design

    Science.gov (United States)

    Lee, Esther; Wurster, Kathryn E.

    2017-01-01

    A typical entry vehicle design depends on the synthesis of many essential subsystems, including thermal protection system (TPS), structures, payload, avionics, and propulsion, among others. The ability to incorporate aerothermodynamic considerations and TPS design into the early design phase is crucial, as both are closely coupled to the vehicle's aerodynamics, shape and mass. In the preliminary design stage, reasonably accurate results with rapid turn-representative entry envelope was explored. Initial results suggest that for Mach numbers ranging from 9-20, a few inviscid solutions could reasonably sup- port surface heating predictions at Mach numbers variation of +/-2, altitudes variation of +/-10 to 20 kft, and angle-of-attack variation of +/- 5. Agreement with Navier-Stokes solutions was generally found to be within 10-15% for Mach number and altitude, and 20% for angle of attack. A smaller angle-of-attack increment than the 5 deg around times for parametric studies and quickly evolving configurations are necessary to steer design decisions. This investigation considers the use of an unstructured 3D inviscid code in conjunction with an integral boundary-layer method; the former providing the flow field solution and the latter the surface heating. Sensitivity studies for Mach number, angle of attack, and altitude, examine the feasibility of using this approach to populate a representative entry flight envelope based on a limited set of inviscid solutions. Each inviscid solution is used to generate surface heating over the nearby trajectory space. A subset of a considered in this study is recommended. Results of the angle-of-attack sensitivity studies show that smaller increments may be needed for better heating predictions. The approach is well suited for application to conceptual multidisciplinary design and analysis studies where transient aeroheating environments are critical for vehicle TPS and thermal design. Concurrent prediction of aeroheating

  7. A multidisciplinary environmental integrated approach to better understand the Tegnue Reefs formation, offshore Chioggia, Northern Adriatic Sea.

    Science.gov (United States)

    Bergamasco, Andrea; Donnici, Sandra; Tosi, Luigi; Tagliapietra, Davide; Zaggia, Luca; Bonaldo, Davide; Braga, Federica; Da Lio, Cristina; Keppel, Erica; Lorenzetti, Giuliano; Manfè, Giorgia; Franceschini, Gianluca; Giovanardi, Otello; Carol, Eleonora; Fornaro, Elena; Grant, Carley

    2014-05-01

    Several hard substrata cover the northwestern Adriatic shelf around 20 m depth as patchy reefs called 'Tegnue'. These submerged reefs form many discrete sets from offshore Grado south to the Po river delta with a large field located off Chioggia. Even if the outer part of the reef is constituted by a thick biogenic formation the underlying structure, mainly buried, is made by cemented sand and this seems to be correlated with its origin not yet fully understood. Different genetic interpretations have been proposed thus far, contemplating among other cementation due to beach-rock like processes (e.g., Stefanon, 1969, Bonardi and Tosi, 2002, Bonardi et al., 2006) or the action of ascending fluids enriched in hydrocarbons (e.g., Gabbianelli et al., 1997, Casellato and Stefanon, 2008). An on-going project, mainly a multidisciplinary integrated approach, combining physical, biological, geological, geomorphological, hydrogeological and geochemical data, supported by a detailed bathymetric mapping, an overall general circulation modeling at high resolution, a robust geophysical evidence, and detailed underwater surveys performed by a team of scuba-diver scientists, aims to better understand the genetic processes backing the distribution, early genesis and evolution of such relevant habitats. Actually, using all the new available data, our plan is to verify which previous interpretations on the origin of the Tegnue core better match with the diagenetic processes that led to the cementation of the sand layers lying at the base of the organic reefs. Preliminary results suggest that the Tegnue reefs formed along paleochannels features related to the former alluvial plain and submerged by the Holocene transgression. Whatever their genesis, once exposed such rocky substrata are then quickly colonized by living organisms, which contribute to the growth and expansion of the reef. Calcareous algae and in general the organic concretion could have a role during the reef accretion

  8. Design of integral magnetic field sensor

    International Nuclear Information System (INIS)

    Ma Liang; Cheng Yinhui; Wu Wei; Li Baozhong; Zhou Hui; Li Jinxi; Zhu Meng

    2010-01-01

    Magnetic field is one of the important physical parameters in the measuring process of pulsed EMP. We researched on anti-interference and high-sensitivity measurement technique of magnetic field in this report. Semi rigid cables were to bent into ringed antenna so that the antenna was shielded from electric-field interference and had little inductance; In order to have high sensitivity, operational transconductance amplifier was used to produce an active integrator; We designed an optical-electronic transferring module to upgrade anti-interference capability of the magnetic-field measurement system. A measurement system of magnetic field was accomplished. The measurement system was composed of antenna, integrator, and optical-electric transferring module and so on. We calibrated the measurement system in coaxial TEM cell. It indicates that, the measurement system's respondence of rise time is up to 2.5 ns, and output width at 90%-maximum of the pulse is wider than 200 ns. (authors)

  9. Conceptual design of inherently safe integral reactor

    Energy Technology Data Exchange (ETDEWEB)

    Kim, J. I.; Chang, M. H.; Lee, D. J. and others

    1999-03-01

    The design concept of a 300 MWt inherently safe integral reactor(ISIR) for the propulsion of extra large and superhigh speed container ship was developed in this report. The scope and contents of this report are as follows : 1. The state of the art of the technology for ship-mounted reactor 2. Design requirements for ISIR 3. Fuel and core design 4. Conceptual design of fluid system 5. Conceptual design of reactor vessel assembly and primary components 6. Performance analyses and safety analyses. Installation of two ISIRs with total thermal power of 600MWt and efficiency of 21% is capable of generating shaft power of 126,000kW which is sufficient to power a container ship of 8,000TEU with 30knot cruise speed. Larger and speedier ship can be considered by installing 4 ISIRs. Even though the ISIR was developed for ship propulsion, it can be used also for a multi-purpose nuclear power plant for electricity generation, local heating, or seawater desalination by mounting on a movable floating barge. (author)

  10. Integrated design of the SSC linac injector

    International Nuclear Information System (INIS)

    Evans, D.; Valiecnti, R.; Wood, F.

    1992-01-01

    The Ion Source, Low Energy Beam Transport (LEBT), and Radio Frequency Quadrupole (RFQ) of the Superconducting Super Collider (SSC) Linac act as a unit (referred to as the Linac Injector), the Ion Source and LEBT being cantilevered off of the RFQ. Immediately adjacent to both ends of the RFQ cavity proper are endwall chambers containing beam instrumentation and independently-operated vacuum isolation valves. The Linac Injector delivers 30 mA of H - beam at 2.5 MeV. This paper describes the design constraints imposed on the endwalls, aspects of the integration of the Ion Source and LEBT including attachment to the RFQ, maintainability and interchangeability of LEBTs, vacuum systems for each component, and the design of necessary support structure. (Author) 2 tab

  11. Integrated safeguards and facility design and operations

    International Nuclear Information System (INIS)

    Tape, J.W.; Coulter, C.A.; Markin, J.T.; Thomas, K.E.

    1987-01-01

    The integration of safeguards functions to deter or detect unauthorized actions by an insider requires the careful communication and management of safeguards-relevant information on a timely basis. The traditional separation of safeguards functions into physical protection, materials control, and materials accounting often inhibits important information flows. Redefining the major safeguards functions as authorization, enforcement, and verification, and careful attention to management of information from acquisition to organization, to analysis, to decision making can result in effective safeguards integration. The careful inclusion of these ideas in facility designs and operations will lead to cost-effective safeguards systems. The safeguards authorization function defines, for example, personnel access requirements, processing activities, and materials movements/locations that are permitted to accomplish the mission of the facility. Minimizing the number of authorized personnel, limiting the processing flexibility, and maintaining up-to-date flow sheets will facilitate the detection of unauthorized activities. Enforcement of the authorized activities can be achieved in part through the use of barriers, access control systems, process sensors, and health and safety information. Consideration of safeguards requirements during facility design can improve the enforcement function. Verification includes the familiar materials accounting activities as well as auditing and testing of the other functions

  12. Designing TSVs for 3D Integrated Circuits

    CERN Document Server

    Khan, Nauman

    2013-01-01

    This book explores the challenges and presents best strategies for designing Through-Silicon Vias (TSVs) for 3D integrated circuits.  It describes a novel technique to mitigate TSV-induced noise, the GND Plug, which is superior to others adapted from 2-D planar technologies, such as a backside ground plane and traditional substrate contacts. The book also investigates, in the form of a comparative study, the impact of TSV size and granularity, spacing of C4 connectors, off-chip power delivery network, shared and dedicated TSVs, and coaxial TSVs on the quality of power delivery in 3-D ICs. The authors provide detailed best design practices for designing 3-D power delivery networks.  Since TSVs occupy silicon real-estate and impact device density, this book provides four iterative algorithms to minimize the number of TSVs in a power delivery network. Unlike other existing methods, these algorithms can be applied in early design stages when only functional block- level behaviors and a floorplan are available....

  13. Applied Integrated Design in Composite UAV Development

    Science.gov (United States)

    Vasić, Zoran; Maksimović, Stevan; Georgijević, Dragutin

    2018-04-01

    This paper presents a modern approach to integrated development of Unmanned Aerial Vehicle made of laminated composite materials from conceptual design, through detail design, strength and stiffness analyses, definition and management of design and production data, detailed tests results and other activities related to development of laminated composite structures with main of its particularities in comparison to metal structures. Special attention in this work is focused to management processes of product data during life cycle of an UAV and experimental tests of its composite wing. Experience shows that the automation management processes of product data during life cycle, as well as processes of manufacturing, are inevitable if a company wants to get cheaper and quality composite aircraft structures. One of the most effective ways of successful management of product data today is Product Life cycle Management (PLM). In terms of the PLM, a spectrum of special measures and provisions has to be implemented when defining fiber-reinforced composite material structures in comparison to designing with metals which is elaborated in the paper.

  14. Integrated computer-aided design using minicomputers

    Science.gov (United States)

    Storaasli, O. O.

    1980-01-01

    Computer-Aided Design/Computer-Aided Manufacturing (CAD/CAM), a highly interactive software, has been implemented on minicomputers at the NASA Langley Research Center. CAD/CAM software integrates many formerly fragmented programs and procedures into one cohesive system; it also includes finite element modeling and analysis, and has been interfaced via a computer network to a relational data base management system and offline plotting devices on mainframe computers. The CAD/CAM software system requires interactive graphics terminals operating at a minimum of 4800 bits/sec transfer rate to a computer. The system is portable and introduces 'interactive graphics', which permits the creation and modification of models interactively. The CAD/CAM system has already produced designs for a large area space platform, a national transonic facility fan blade, and a laminar flow control wind tunnel model. Besides the design/drafting element analysis capability, CAD/CAM provides options to produce an automatic program tooling code to drive a numerically controlled (N/C) machine. Reductions in time for design, engineering, drawing, finite element modeling, and N/C machining will benefit productivity through reduced costs, fewer errors, and a wider range of configuration.

  15. Integrating conceptualizations of experience into the interaction design process

    DEFF Research Database (Denmark)

    Dalsgaard, Peter

    2010-01-01

    From a design perspective, the increasing awareness of experiential aspects of interactive systems prompts the question of how conceptualizations of experience can inform and potentially be integrated into the interaction design process. This paper presents one approach to integrating theoretical...

  16. Process Improvement Through Tool Integration in Aero-Mechanical Design

    Science.gov (United States)

    Briggs, Clark

    2010-01-01

    Emerging capabilities in commercial design tools promise to significantly improve the multi-disciplinary and inter-disciplinary design and analysis coverage for aerospace mechanical engineers. This paper explores the analysis process for two example problems of a wing and flap mechanical drive system and an aircraft landing gear door panel. The examples begin with the design solid models and include various analysis disciplines such as structural stress and aerodynamic loads. Analytical methods include CFD, multi-body dynamics with flexible bodies and structural analysis. Elements of analysis data management, data visualization and collaboration are also included.

  17. Integrated design of SIGMA uranium enrichment plants

    International Nuclear Information System (INIS)

    Rivarola, Martin E.; Brasnarof, Daniel O.

    1999-01-01

    In the present work, we describe a preliminary analysis of the design feedbacks in a Uranium Enrichment Plant, using the SIGMA concept. Starting from the result of this analysis, a computer code has been generated, which allows finding the optimal configurations of plants, for a fixed production rate. The computer code developed includes the model of the Thermohydraulic loop of a SIGMA module. The model contains numerical calculations of the main components of the circuit. During the calculations, the main components are dimensioned, for a posterior cost compute. The program also makes an estimation of the enrichment gain of the porous membrane, for each separation stage. Once the dimensions of the main components are known, using the enrichment cascade calculation, the capital and operation costs of the plant could be determined. At this point it is simple to calculate a leveled cost of the Separative Work Unit (SWU). A numerical optimizer is also included in the program. This optimizer finds the optimal cascade configuration, for a given set of design parameters. The whole-integrated program permits to investigate in detail the feedback in the component design. Therefore, the sensibility of the more relevant parameters can be computed, with respect of the economical variables of the plant. (author)

  18. Toward integrated design of waste management technologies

    International Nuclear Information System (INIS)

    Carnes, S.A.; Wolfe, A.K.

    1994-01-01

    Implementation of waste management technologies has been hindered by the intervention of diverse interests. Relying on a perceived history of inadequate and improper management, operations, and technological design, critics have stymied the implementation of scientifically and governmentally approved technologies and facilities, leading to a critical shortage of hazardous, mixed, and radioactive waste management capacity. The research and development (R ampersand D) required to identify technologies that are simultaneously (1) scientifically valid, (2) economically sound, and (3) publicly acceptable must necessarily address, in an integrated and interdisciplinary manner, these three criteria and how best to achieve the integration of stakeholders early in the technology implementation process (i.e., R ampersand D, demonstration, and commercialization). The goal of this paper is to initiate an identification of factors likely to render radioactive and hazardous waste management technologies publicly acceptable and to provide guidance on how technological R ampersand D might be revised to enhance the acceptability of alternative waste management technologies. Principal among these factors are the equitable distribution of costs, risks, and benefits of waste management policies and technologies, the equitable distribution of authority for making waste management policy and selecting technologies for implementation, and the equitable distribution of responsibility for resolving waste management problems. Stakeholder participation in assessing the likely distribution of these factors and mitigative mechanisms to enhance their equitable distribution, together with stakeholder participation in policy and technology R ampersand D, as informed by stakeholder assessments, should enhance the identification of acceptable policies and technologies

  19. DEMO port plug design and integration studies

    Science.gov (United States)

    Grossetti, G.; Boccaccini, L. V.; Cismondi, F.; Del Nevo, A.; Fischer, U.; Franke, T.; Granucci, G.; Hernández, F.; Mozzillo, R.; Strauß, D.; Tran, M. Q.; Vaccaro, A.; Villari, R.

    2017-11-01

    The EUROfusion Consortium established in 2014 and composed by European Fusion Laboratories, and in particular the Power Plant Physics and Technology department aims to develop a conceptual design for the Fusion DEMOnstration Power Plant, DEMO. With respect to present experimental machines and ITER, the main goals of DEMO are to produce electricity continuously for a period of about 2 h, with a net electrical power output of a few hundreds of MW, and to allow tritium self-sufficient breeding with an adequately high margin in order to guarantee its planned operational schedule, including all planned maintenance intervals. This will eliminate the need to import tritium fuel from external sources during operations. In order to achieve these goals, extensive engineering efforts as well as physics studies are required to develop a design that can ensure a high level of plant reliability and availability. In particular, interfaces between systems must be addressed at a very early phase of the project, in order to proceed consistently. In this paper we present a preliminary design and integration study, based on physics assessments for the EU DEMO1 Baseline 2015 with an aspect ratio of 3.1 and 18 toroidal field coils, for the DEMO port plugs. These aim to host systems like electron cyclotron heating launchers currently developed within the Work Package Heating and Current Drive that need an external radial access to the plasma and through in-vessel systems like the breeder blanket. A similar approach shown here could be in principle followed by other systems, e.g. other heating and current drive systems or diagnostics. The work addresses the interfaces between the port plug and the blanket considering the helium-cooled pebble bed and the water cooled lithium lead which are two of four breeding blanket concepts under investigation in Europe within the Power Plant Physics and Technology Programme: the required openings will be evaluated in terms of their impact onto the

  20. Designing Mechatronic Products - Achieving Integration by Means of Modelling Dependencies

    DEFF Research Database (Denmark)

    Torry-Smith, Jonas

    of a joint effort between mechanical, electronics and software development. Companies engaged in multi-disciplinary product development face the challenge of coordinating different engineering disciplines to pursue a synergistic effect and to avoid failures when solutions from the different engineering...... disciplines have to be combined and function in an integrated fashion. The holistic view of the product concept is sometimes missing in projects and engineering disciplines are reluctant to interact. Investigations of literature, cases from industry and practical experience are used for dissecting...

  1. Integrated Business and Engineering Framework for Synthesis and Design of Enterprise-Wide Processing Networks

    DEFF Research Database (Denmark)

    Quaglia, Alberto; Sarup, Bent; Sin, Gürkan

    2012-01-01

    The synthesis and design of processing networks is a complex and multidisciplinary problem, which involves many strategic and tactical decisions at business (considering financial criteria, market competition, supply chain network, etc) and engineering levels (considering synthesis, design...... and optimisation of production technology, R&D, etc), all of which have a deep impact on the profitability of processing industries. In this study, an integrated business and engineering framework for synthesis and design of processing networks is presented. The framework employs a systematic approach to manage...... the complexity while solving simultaneously both the business and the engineering aspects of problems, allowing at the same time, comparison of a large number of alternatives at their optimal points. The results identify the optimal raw material, the product portfolio and select the process technology...

  2. Integrated Task And Data Parallel Programming: Language Design

    Science.gov (United States)

    Grimshaw, Andrew S.; West, Emily A.

    1998-01-01

    his research investigates the combination of task and data parallel language constructs within a single programming language. There are an number of applications that exhibit properties which would be well served by such an integrated language. Examples include global climate models, aircraft design problems, and multidisciplinary design optimization problems. Our approach incorporates data parallel language constructs into an existing, object oriented, task parallel language. The language will support creation and manipulation of parallel classes and objects of both types (task parallel and data parallel). Ultimately, the language will allow data parallel and task parallel classes to be used either as building blocks or managers of parallel objects of either type, thus allowing the development of single and multi-paradigm parallel applications. 1995 Research Accomplishments In February I presented a paper at Frontiers '95 describing the design of the data parallel language subset. During the spring I wrote and defended my dissertation proposal. Since that time I have developed a runtime model for the language subset. I have begun implementing the model and hand-coding simple examples which demonstrate the language subset. I have identified an astrophysical fluid flow application which will validate the data parallel language subset. 1996 Research Agenda Milestones for the coming year include implementing a significant portion of the data parallel language subset over the Legion system. Using simple hand-coded methods, I plan to demonstrate (1) concurrent task and data parallel objects and (2) task parallel objects managing both task and data parallel objects. My next steps will focus on constructing a compiler and implementing the fluid flow application with the language. Concurrently, I will conduct a search for a real-world application exhibiting both task and data parallelism within the same program m. Additional 1995 Activities During the fall I collaborated

  3. Architectures for Green-Field Supply Chain Integration: Supply Chain Integration Design

    OpenAIRE

    Radanliev, Petar

    2015-01-01

    This paper applied case study research to design architectures for green-field supply chain integration. The integration design is based on a case study of a supply chain integration of 5 companies, operating in different, but supply chain complimenting industry sectors. The case study research is applied to design and validate the architectures in a real world scenario. The supply\\ud chain integration architectures enable the conversion of individual into integrated strategies. The architect...

  4. Design integration of liquid surface divertors

    International Nuclear Information System (INIS)

    Nygren, R.E.; Cowgill, D.F.; Ulrickson, M.A.; Nelson, B.E.; Fogarty, P.J.; Rognlien, T.D.; Rensink, M.E.; Hassanein, A.; Smolentsev, S.S.; Kotschenreuther, M.

    2004-01-01

    The US Enabling Technology Program in fusion is investigating the use of free flowing liquid surfaces facing the plasma. We have been studying the issues in integrating a liquid surface divertor into a configuration based upon an advanced tokamak, specifically the ARIES-RS configuration. The simplest form of such a divertor is to extend the flow of the liquid first wall into the divertor and thereby avoid introducing additional fluid streams. In this case, one can modify the flow above the divertor to enhance thermal mixing. For divertors with flowing liquid metals (or other electrically conductive fluids) MHD (magneto-hydrodynamics) effects are a major concern and can produce forces that redirect flow and suppress turbulence. An evaluation of Flibe (a molten salt) as a working fluid was done to assess a case in which the MHD forces could be largely neglected. Initial studies indicate that, for a tokamak with high power density, an integrated Flibe first wall and divertor does not seem workable. We have continued work with molten salts and replaced Flibe with Flinabe, a mixture of lithium, sodium and beryllium fluorides, that has some potential because of its lower melting temperature. Sn and Sn-Li have also been considered, and the initial evaluations on heat removal with minimal plasma contamination show promise, although the complicated 3D MHD flows cannot yet be fully modeled. Particle pumping in these design concepts is accomplished by conventional means (ports and pumps). However, trapping of hydrogen in these flowing liquids seems plausible and novel concepts for entrapping helium are also being studied

  5. Ground Vehicle System Integration (GVSI) and Design Optimization Model

    National Research Council Canada - National Science Library

    Horton, William

    1996-01-01

    This report documents the Ground Vehicle System Integration (GVSI) and Design Optimization Model GVSI is a top-level analysis tool designed to support engineering tradeoff studies and vehicle design optimization efforts...

  6. Integration of design applications with building models

    DEFF Research Database (Denmark)

    Eastman, C. M.; Jeng, T. S.; Chowdbury, R.

    1997-01-01

    This paper reviews various issues in the integration of applications with a building model... (Truncated.)......This paper reviews various issues in the integration of applications with a building model... (Truncated.)...

  7. From user needs to system specifications: multi-disciplinary thematic seminars as a collaborative design method for development of health information systems.

    Science.gov (United States)

    Scandurra, I; Hägglund, M; Koch, S

    2008-08-01

    This paper presents a new multi-disciplinary method for user needs analysis and requirements specification in the context of health information systems based on established theories from the fields of participatory design and computer supported cooperative work (CSCW). Whereas conventional methods imply a separate, sequential needs analysis for each profession, the "multi-disciplinary thematic seminar" (MdTS) method uses a collaborative design process. Application of the method in elderly homecare resulted in prototypes that were well adapted to the intended user groups. Vital information in the points of intersection between different care professions was elicited and a holistic view of the entire care process was obtained. Health informatics-usability specialists and clinical domain experts are necessary to apply the method. Although user needs acquisition can be time-consuming, MdTS was perceived to efficiently identify in-context user needs, and transformed these directly into requirements specifications. Consequently the method was perceived to expedite the entire ICT implementation process.

  8. Designing interaction behaviour in service-oriented enterprise application integration

    NARCIS (Netherlands)

    Dirgahayu, T.; Quartel, Dick; van Sinderen, Marten J.

    In this paper we present an approach for designing interaction behaviour in service-oriented enterprise application integration. The approach enables business analysts to actively participate in the design of an integration solution. In this way, we expect that the solution meets its integration

  9. Integral Design methodology for Industrial Collaboration Design of Sustainable Industrial Flexible Demountable buildings

    NARCIS (Netherlands)

    Zeiler, W.; Quanjel, E.M.C.J.; Bauer, M.; Lima, C.

    2007-01-01

    Starting in 1998 from developing and designing their own office Kropman, a major Dutch Building Services contractor, developed a new methodology for structuring and documenting integral design processes. Integral design is meant to integrate the different disciplines involved in the building design

  10. Integrated network design and scheduling problems :

    Energy Technology Data Exchange (ETDEWEB)

    Nurre, Sarah G.; Carlson, Jeffrey J.

    2014-01-01

    We consider the class of integrated network design and scheduling problems. These problems focus on selecting and scheduling operations that will change the characteristics of a network, while being speci cally concerned with the performance of the network over time. Motivating applications of INDS problems include infrastructure restoration after extreme events and building humanitarian distribution supply chains. While similar models have been proposed, no one has performed an extensive review of INDS problems from their complexity, network and scheduling characteristics, information, and solution methods. We examine INDS problems under a parallel identical machine scheduling environment where the performance of the network is evaluated by solving classic network optimization problems. We classify that all considered INDS problems as NP-Hard and propose a novel heuristic dispatching rule algorithm that selects and schedules sets of arcs based on their interactions in the network. We present computational analysis based on realistic data sets representing the infrastructures of coastal New Hanover County, North Carolina, lower Manhattan, New York, and a realistic arti cial community CLARC County. These tests demonstrate the importance of a dispatching rule to arrive at near-optimal solutions during real-time decision making activities. We extend INDS problems to incorporate release dates which represent the earliest an operation can be performed and exible release dates through the introduction of specialized machine(s) that can perform work to move the release date earlier in time. An online optimization setting is explored where the release date of a component is not known.

  11. Flexible heat pipes with integrated bioinspired design

    Directory of Open Access Journals (Sweden)

    Chao Yang

    2015-02-01

    Full Text Available In this work we report the facile fabrication and performance evaluation of flexible heat pipes that have integrated bioinspired wick structures and flexible polyurethane polymer connector design between the copper condenser and evaporator. Inside the heat pipe, a bioinspired superhydrophilic strong-base-oxidized copper mesh with multi-scale micro/nano-structures was used as the wicking material and deionized water was selected as working fluid. Thermal resistances of the fabricated flexible heat pipes charged with different filling ratios were measured under thermal power inputs ranging from 2 W to 12 W while the device was bent at different angles. The fabricated heat pipes with a 30% filling ratio demonstrated a low thermal resistance less than 0.01 K/W. Compared with the vertically oriented straight heat pipes, bending from 30° up to 120° has negligible influence on the heat-transfer performance. Furthermore, repeated heating tests indicated that the fabricated flexible heat pipes have consistent and reliable heat-transfer performance, thus would have important applications for advanced thermal management in three dimensional and flexible electronic devices.

  12. Building multidisciplinary health workforce capacity to support the implementation of integrated, people-centred Models of Care for musculoskeletal health.

    Science.gov (United States)

    Chehade, M J; Gill, T K; Kopansky-Giles, D; Schuwirth, L; Karnon, J; McLiesh, P; Alleyne, J; Woolf, A D

    2016-06-01

    To address the burden of musculoskeletal (MSK) conditions, a competent health workforce is required to support the implementation of MSK models of care. Funding is required to create employment positions with resources for service delivery and training a fit-for-purpose workforce. Training should be aligned to define "entrustable professional activities", and include collaborative skills appropriate to integrated and people-centred care and supported by shared education resources. Greater emphasis on educating MSK healthcare workers as effective trainers of peers, students and patients is required. For quality, efficiency and sustainability of service delivery, education and research capabilities must be integrated across disciplines and within the workforce, with funding models developed based on measured performance indicators from all three domains. Greater awareness of the societal and economic burden of MSK conditions is required to ensure that solutions are prioritised and integrated within healthcare policies from local to regional to international levels. These healthcare policies require consumer engagement and alignment to social, economic, educational and infrastructure policies to optimise effectiveness and efficiency of implementation. Copyright © 2016 Elsevier Ltd. All rights reserved.

  13. Integral Design workshops: organization, structure and testing

    OpenAIRE

    Zeiler, W Wim; Savanovic, P Perica

    2010-01-01

    The purpose of this paper is to achieve an understanding of design activities in the context of building design. The starting point is an overview of design research and design methodology. From the insights gained by this analysis of design in this specific context, we present an 'organization structure and design' workshop approach for collaborative multi-discipline design management. The workshops set-up, used to implement and to test the approach, are presented as well as the experiences ...

  14. Integral Design workshops: organization, structure and testing

    NARCIS (Netherlands)

    Zeiler, W.; Savanovic, P.

    2010-01-01

    The purpose of this paper is to achieve an understanding of design activities in the context of building design. The starting point is an overview of design research and design methodology. From the insights gained by this analysis of design in this specific context, we present an ‘organization

  15. Designing Integrated Product- Service System Solutions in Manufacturing Industries

    DEFF Research Database (Denmark)

    Costa, Nina; Patrício, Lia; Morelli, Nicola

    2015-01-01

    Manufacturing firms are increasingly evolving towards the design of integrated product-service solutions but servitization literature does not provide specific guidance on how to design these integrated solutions. Building upon ProductService System (PSS) and Service Design (SD) approaches...... how it brings new insights to manufacturing companies moving to a service, value cocreation perspective....

  16. A multidisciplinary weight of evidence approach for environmental risk assessment at the Costa Concordia wreck: Integrative indices from Mussel Watch.

    Science.gov (United States)

    Regoli, Francesco; Pellegrini, David; Cicero, Anna Maria; Nigro, Marco; Benedetti, Maura; Gorbi, Stefania; Fattorini, Daniele; D'Errico, Giuseppe; Di Carlo, Marta; Nardi, Alessandro; Gaion, Andrea; Scuderi, Alice; Giuliani, Silvia; Romanelli, Giulia; Berto, Daniela; Trabucco, Benedetta; Guidi, Patrizia; Bernardeschi, Margherita; Scarcelli, Vittoria; Frenzilli, Giada

    2014-05-01

    A complex framework of chemical, biological and oceanographic activities was immediately activated after the Costa Concordia shipwreck, to assess possible contamination events and the environmental impact during both emergency and wreck removal operations. In the present paper, we describe the results obtained with caged mussels, Mytilus galloprovincialis, chosen as bioindicator organisms to detect variations of bioavailability and the early onset of molecular and cellular effects (biomarkers). Seven translocation experiments were carried out during the first year from the incident, with organisms deployed at 2 depths in 3 different sites. After 4-6 weeks, tissue concentrations were measured for the main classes of potentially released chemicals (trace metals, polycyclic aromatic hydrocarbons, volatile and aliphatic hydrocarbons, polychlorinated biphenyls, halogenated pesticides, organotin compounds, brominated flame retardants, anionic surfactants); a wide battery of biomarkers covered responses indicative of exposure, detoxification, oxidative stress, cell damage and genotoxic effects. Results excluded serious contamination events or a consistent increase of environmental pollution although some episodic spills with reversible effects were detected. Data were elaborated within a quantitative weight of evidence (WOE) model which provided synthetic hazard indices for each typology of data, before their overall integration in an environmental risk index, which generally ranged from slight to moderate. The proposed WOE model was confirmed a useful tool to summarize large datasets of complex data in integrative indices, and to simplify the interpretation for stakeholders and decision makers, thus supporting a more comprehensive process of "site-oriented" management decisions. Copyright © 2013 Elsevier Ltd. All rights reserved.

  17. Building Integrated Design Practice under the Concept of Sustainable Development

    Science.gov (United States)

    Liu, Xuexin

    2018-03-01

    With the continuous development of social economy, people are more demanding for architecture. Some advanced design concepts are gradually applied to the design of buildings. Under the concept of sustainable development, building integration design has also been widely used to promote the rapid development of architectural design. Integrated design concepts and sustainable development concepts play an important role to meet people’s requirements. This article will explore the concept of sustainable development under the concept of integrated architectural design and practice analysis, propose appropriate measures.

  18. The ICOS Experience: Integration of Multi-disciplinary Data and Beyond Its Domains Into a Network of Networks

    Science.gov (United States)

    Vermeulen, A. T.; Hellström, M.; Mirzov, O.; Juurola, E.; Lavric, J. V.; Kutsch, W. L.

    2016-12-01

    ICOS as long-term observational system for the carbon cycle has a long history in Europe, but has only recently been established formally as one of the first European Research Infrastructure Consortia (ERIC). ICOS data will be provided through the ICOS Carbon Portal and data usage will be absolutely unrestricted under the Creative Commons Attribution 4.0 International (CC4.0BY) license. ICOS strives to further integrate its data streams internally across the domains and externally, building on scalable open access tools and open data technologies. Through the ENVRIplus project, led by ICOS, and the EUDAT2020 project, the work on interoperability and scalability is now progressing quickly in the European environmental Research Infrastructures domain. In this presentation we will demonstrate the recent progress in ICOS in implementing the Carbon Portal as the one stop shop for ICOS data.

  19. Integrated Intelligent Modeling, Design and Control of Crystal Growth Processes

    National Research Council Canada - National Science Library

    Prasad, V

    2000-01-01

    .... This MURI program took an integrated approach towards modeling, design and control of crystal growth processes and in conjunction with growth and characterization experiments developed much better...

  20. Strategic Mobility 21: Integrated Tracking System Analysis and Concept Design

    National Research Council Canada - National Science Library

    Mallon, Lawrence G; Savacool, Edwin

    2007-01-01

    ... (ITS). This ITS design document identifies the technical and functional requirements for developing, procuring, and integrating components of an ITS capable of supporting an inland regional port, multi...

  1. Integrated optimization on aerodynamics-structure coupling and flight stability of a large airplane in preliminary design

    Directory of Open Access Journals (Sweden)

    Xiaozhe WANG

    2018-06-01

    Full Text Available The preliminary phase is significant during the whole design process of a large airplane because of its enormous potential in enhancing the overall performance. However, classical sequential designs can hardly adapt to modern airplanes, due to their repeated iterations, long periods, and massive computational burdens. Multidisciplinary analysis and optimization demonstrates the capability to tackle such complex design issues. In this paper, an integrated optimization method for the preliminary design of a large airplane is proposed, accounting for aerodynamics, structure, and stability. Aeroelastic responses are computed by a rapid three-dimensional flight load analysis method combining the high-order panel method and the structural elasticity correction. The flow field is determined by the viscous/inviscid iteration method, and the cruise stability is evaluated by the linear small-disturbance theory. Parametric optimization is carried out using genetic algorithm to seek the minimal weight of a simplified plate-beam wing structure in the cruise trim condition subject to aeroelastic, aerodynamic, and stability constraints, and the optimal wing geometry shape, front/rear spar positions, and structural sizes are obtained simultaneously. To reduce the computational burden of the static aeroelasticity analysis in the optimization process, the Kriging method is employed to predict aerodynamic influence coefficient matrices of different aerodynamic shapes. The multidisciplinary analyses guarantee computational accuracy and efficiency, and the integrated optimization considers the coupling effect sufficiently between different disciplines to improve the overall performance, avoiding the limitations of sequential approaches utilized currently. Keywords: Aeroelasticity, Integrated optimization, Multidisciplinary analysis, Large airplane, Preliminary design

  2. Hermeneutics framework: integration of design rationale and optimizing software modules

    NARCIS (Netherlands)

    Aksit, Mehmet; Malakuti Khah Olun Abadi, Somayeh

    To tackle the evolution challenges of adaptive systems, this paper argues on the necessity of hermeneutic approaches that help to avoid too early elimination of design alternatives. This visionary paper proposes the Hermeneutics Framework, which computationally integrates a design rationale

  3. Process Variations and Probabilistic Integrated Circuit Design

    CERN Document Server

    Haase, Joachim

    2012-01-01

    Uncertainty in key parameters within a chip and between different chips in the deep sub micron era plays a more and more important role. As a result, manufacturing process spreads need to be considered during the design process.  Quantitative methodology is needed to ensure faultless functionality, despite existing process variations within given bounds, during product development.   This book presents the technological, physical, and mathematical fundamentals for a design paradigm shift, from a deterministic process to a probability-orientated design process for microelectronic circuits.  Readers will learn to evaluate the different sources of variations in the design flow in order to establish different design variants, while applying appropriate methods and tools to evaluate and optimize their design.  Trains IC designers to recognize problems caused by parameter variations during manufacturing and to choose the best methods available to mitigate these issues during the design process; Offers both qual...

  4. Collaborative integral design of active roofs

    NARCIS (Netherlands)

    Zeiler, W.; Quanjel, E.M.C.J.; Borsboom, W.A.

    2009-01-01

    The application of photo-voltaic elements is the most economical on the roof. Still this often leads to severe problems due to poor coordination of all the design and practical aspects involved. This paper describes the research methodology, based on Methodical Design, as used in a design approach

  5. Study and implementation of urogenital schistosomiasis elimination in Zanzibar (Unguja and Pemba islands using an integrated multidisciplinary approach

    Directory of Open Access Journals (Sweden)

    Knopp Stefanie

    2012-10-01

    Full Text Available Abstract Background Schistosomiasis is a parasitic infection that continues to be a major public health problem in many developing countries being responsible for an estimated burden of at least 1.4 million disability-adjusted life years (DALYs in Africa alone. Importantly, morbidity due to schistosomiasis has been greatly reduced in some parts of the world, including Zanzibar. The Zanzibar government is now committed to eliminate urogenital schistosomiasis. Over the next 3–5 years, the whole at-risk population will be administered praziquantel (40 mg/kg biannually. Additionally, snail control and behaviour change interventions will be implemented in selected communities and the outcomes and impact measured in a randomized intervention trial. Methods/Design In this 5-year research study, on both Unguja and Pemba islands, urogenital schistosomiasis will be assessed in 45 communities with urine filtration and reagent strips in 4,500 schoolchildren aged 9–12 years annually, and in 4,500 first-year schoolchildren and 2,250 adults in years 1 and 5. Additionally, from first-year schoolchildren, a finger-prick blood sample will be collected and examined for Schistosoma haematobium infection biomarkers. Changes in prevalence and infection intensity will be assessed annually. Among the 45 communities, 15 were randomized for biannual snail control with niclosamide, in concordance with preventive chemotherapy campaigns. The reduction of Bulinus globosus snail populations and S. haematobium-infected snails will be investigated. In 15 other communities, interventions triggering behaviour change have been designed and will be implemented in collaboration with the community. A change in knowledge, attitudes and practices will be assessed annually through focus group discussions and in-depth interviews with schoolchildren, teachers, parents and community leaders. In all 45 communities, changes in the health system, water and sanitation infrastructure will

  6. Managing brain metastases patients with and without radiotherapy: initial lessonsfrom a team-based consult service through a multidisciplinary integrated palliative oncology clinic.

    Science.gov (United States)

    Jung, Hellen; Sinnarajah, Aynharan; Enns, Bert; Voroney, Jon-Paul; Murray, Alison; Pelletier, Guy; Wu, Jackson Sai-Yiu

    2013-12-01

    A new ambulatory consultative clinic with integrated assessments by palliative care, radiation oncology, and allied health professionals was introduced to (1) assess patients with brain metastases at a regional comprehensive cancer center and (2) inform and guide patients on management strategies, including palliative radiotherapy, symptom control, and end-of-life care issues. We conducted a quality assurance study to inform clinical program development. Between January 2011 and May 2012, 100 consecutive brain metastases patients referred and assessed through a multidisciplinary clinic were evaluated for baseline characteristics, radiotherapy use, and supportive care decisions. Overall survival was examined by known prognostic groups. Proportion of patients receiving end-of-life radiotherapy (death within 30 and 14 days of brain radiotherapy) was used as a quality metric. The median age was 65 years, with non-small cell lung cancer (n = 38) and breast cancer (n = 23) being the most common primary cancers. At least 57 patients were engaged in advance care planning discussions at first consult visit. In total, 75 patients eventually underwent brain radiotherapy, whereas 25 did not. The most common reasons for nonradiotherapy management were patient preference and rapid clinical deterioration. Overall survival for prognostic subgroups was consistent with literature reports. End-of-life brain radiotherapy was observed in 9 % (death within 30 days) and 1 % (within 14 days) of treated patients. By integrating palliative care expertise to address the complex needs of patients with newly diagnosed brain metastases, end-of-life radiotherapy use appears acceptable and improved over historical rates at our institution. An appreciable proportion of patients are not suitable for palliative brain radiotherapy or opt against this treatment option, but the team approach involving nurses, palliative care experts, allied health, and clinical oncologists facilitates

  7. Global design of an active integrated antenna for millimeter wave

    OpenAIRE

    Marzolf, Eric; Drissi, M’hamed

    2001-01-01

    An active integrated antenna working in the millimeter wave has been realized in a monolithic process. The concept of active integrated antenna is first introduced, then the design of the integrated circuit based on a global approach, following electromagnetic and circuit simulations, is presented. The obtained performances of the active antenna are discussed and compared to a passive one.

  8. Multidisciplinary Approaches to Allergies

    NARCIS (Netherlands)

    Gao Zhongshan,; Shen, Hua-Hao; Zheng, M.; Frewer, L.J.; Gilissen, L.J.W.J.

    2012-01-01

    Allergy is an immunological disease caused by multiple factors and characterized by variability, specificity and complexity. "Multidisciplinary Approaches to Allergies" covers diverse aspects ranging from basic molecular mechanisms to societal issues within the framework of multidisciplinary

  9. Design of 3D integrated circuits and systems

    CERN Document Server

    Sharma, Rohit

    2014-01-01

    Three-dimensional (3D) integration of microsystems and subsystems has become essential to the future of semiconductor technology development. 3D integration requires a greater understanding of several interconnected systems stacked over each other. While this vertical growth profoundly increases the system functionality, it also exponentially increases the design complexity. Design of 3D Integrated Circuits and Systems tackles all aspects of 3D integration, including 3D circuit and system design, new processes and simulation techniques, alternative communication schemes for 3D circuits and sys

  10. Advanced Concept Architecture Design and Integrated Analysis (ACADIA)

    Science.gov (United States)

    2017-11-03

    1 Advanced Concept Architecture Design and Integrated Analysis (ACADIA) Submitted to the National Institute of Aerospace (NIA) on...Research Report 20161001 - 20161030 Advanced Concept Architecture Design and Integrated Analysis (ACADIA) W911NF-16-2-0229 8504Cedric Justin, Youngjun

  11. The Exploration of Green Architecture Design Integration Teaching Mode

    Science.gov (United States)

    Shuang, Liang; Yibin, Han

    2016-01-01

    With the deepening of the concept of green building design, the course of university education gradually exposed many problems in the teaching of architectural design theory; based on the existing mode of teaching and combined with the needs of architectural design practice it proposed the "integrated" method of green building design. It…

  12. Information Management for a Large Multidisciplinary Project

    Science.gov (United States)

    Jones, Kennie H.; Randall, Donald P.; Cronin, Catherine K.

    1992-01-01

    In 1989, NASA's Langley Research Center (LaRC) initiated the High-Speed Airframe Integration Research (HiSAIR) Program to develop and demonstrate an integrated environment for high-speed aircraft design using advanced multidisciplinary analysis and optimization procedures. The major goals of this program were to evolve the interactions among disciplines and promote sharing of information, to provide a timely exchange of information among aeronautical disciplines, and to increase the awareness of the effects each discipline has upon other disciplines. LaRC historically has emphasized the advancement of analysis techniques. HiSAIR was founded to synthesize these advanced methods into a multidisciplinary design process emphasizing information feedback among disciplines and optimization. Crucial to the development of such an environment are the definition of the required data exchanges and the methodology for both recording the information and providing the exchanges in a timely manner. These requirements demand extensive use of data management techniques, graphic visualization, and interactive computing. HiSAIR represents the first attempt at LaRC to promote interdisciplinary information exchange on a large scale using advanced data management methodologies combined with state-of-the-art, scientific visualization techniques on graphics workstations in a distributed computing environment. The subject of this paper is the development of the data management system for HiSAIR.

  13. EPR design tools. Integrated data processing tools

    International Nuclear Information System (INIS)

    Kern, R.

    1997-01-01

    In all technical areas, planning and design have been supported by electronic data processing for many years. New data processing tools had to be developed for the European Pressurized Water Reactor (EPR). The work to be performed was split between KWU and Framatome and laid down in the Basic Design contract. The entire plant was reduced to a logical data structure; the circuit diagrams and flowsheets of the systems were drafted, the central data pool was established, the outlines of building structures were defined, the layout of plant components was planned, and the electrical systems were documented. Also building construction engineering was supported by data processing. The tasks laid down in the Basic Design were completed as so-called milestones. Additional data processing tools also based on the central data pool are required for the phases following after the Basic Design phase, i.e Basic Design Optimization; Detailed Design; Management; Construction, and Commissioning. (orig.) [de

  14. Integrated Design as an Evolutive Transdisciplinary Strategy

    OpenAIRE

    Bujar Bajçinovci; Florina Jerliu

    2016-01-01

    New challenges should stimulate new research, in order to provide better and higher quality of life. The essence of transdisciplinary design consists of different professions closely related to architectural design aiming for better and qualitative solutions, which with new findings exceed the usual and conventional disciplinary boundaries. Incentive mechanism for lateral thinking in the design process is accomplished when all the team members overcome a conventional barrier, in creating fund...

  15. Design of Integrated Circuits Approaching Terahertz Frequencies

    DEFF Research Database (Denmark)

    Yan, Lei

    In this thesis, monolithic microwave integrated circuits(MMICs) are presented for millimeter-wave and submillimeter-wave or terahertz(THz) applications. Millimeter-wave power generation from solid state devices is not only crucial for the emerging high data rate wireless communications but also...... heterodyne receivers with requirements of room temperature operation, low system complexity, and high sensitivity, monolithic integrated Schottky diode technology is chosen for the implementation of submillimeterwave components. The corresponding subharmonic mixer and multiplier for a THz radiometer system...

  16. “Partners rather than just providers…”: A qualitative study on health care professionals’ views on implementation of multidisciplinary group meetings in the North West London Integrated Care Pilot

    Directory of Open Access Journals (Sweden)

    Angelos P Kassianos

    2015-09-01

    Full Text Available Introduction: Multidisciplinary group meetings are one of the key drivers of facilitating integrated care. Health care professionals attending such groups have a key role in the success of these discussions and hence, in the forming of multi-professional integrated care. The study aimed to explore the professionals’ experiences and views of participating and implementing the groups in integrated care context. Methods: A qualitative study including 25 semi-structured interviews with professionals participating in the Northwest London Integrated Care Pilot analysed using thematic content analysis. Results: Participants mentioned a number of benefits of participating in the meetings, including shared learning and shared decision-making between different services and specialties. Yet, they perceived barriers that diminish the efficiency of the groups, such as time constraints, group dynamics and technicalities. The participants felt that the quality of discussions and facilitation could be improved, as well as technical arrangements that would make them easier to participate. Most of the participants perceived the groups to be beneficial for providers mostly questioning the benefits for patient care. Conclusion: Findings provide an insight into how health professionals’ views of their participation to the multidisciplinary group meetings can be more effectively translated into more tangible benefits to the patients. To benefit patient care, the multidisciplinary groups need to be more patient-oriented rather than provider-oriented, while overcoming professional boundaries for participating.

  17. Integrated magnetics design for HF-link power converters

    Energy Technology Data Exchange (ETDEWEB)

    Ljusev, P.; Andersen, Michael A.E.

    2005-07-01

    This paper deals with the design of integrated magnetics for HF-link converters, where the two integrated magnetic components on the same core do not necessarily belong to the same voltage loop. Depending on the specific HF-link converter topology, the proposed integrated magnetics can either alleviate the derivation of independent auxiliary supply voltages from the main transformer or integrate other magnetic structures, thus saving board space and cutting costs. (au)

  18. Integrating Mediators and Moderators in Research Design

    Science.gov (United States)

    MacKinnon, David P.

    2011-01-01

    The purpose of this article is to describe mediating variables and moderating variables and provide reasons for integrating them in outcome studies. Separate sections describe examples of moderating and mediating variables and the simplest statistical model for investigating each variable. The strengths and limitations of incorporating mediating…

  19. Integrated Design Tools for Embedded Control Systems

    NARCIS (Netherlands)

    Jovanovic, D.S.; Hilderink, G.H.; Broenink, Johannes F.; Karelse, F.

    2001-01-01

    Currently, computer-based control systems are still being implemented using the same techniques as 10 years ago. The purpose of this project is the development of a design framework, consisting of tools and libraries, which allows the designer to build high reliable heterogeneous real-time embedded

  20. Cost-effectiveness of a multifaceted implementation strategy for the Dutch multidisciplinary guideline for nonspecific low back pain: design of a stepped-wedge cluster randomised controlled trial.

    Science.gov (United States)

    Suman, Arnela; Schaafsma, Frederieke G; Elders, Petra J M; van Tulder, Maurits W; Anema, Johannes R

    2015-05-31

    Low back pain (LBP) is one of the most prevalent and expensive health care problems in industrialised countries. LBP leads to high health care utility and productivity losses; leaving the individual, the employer, and society with substantial costs. To improve the care for LBP patients and reduce the high societal and financial burden of LBP, in 2010 the 'Multidisciplinary care guideline for nonspecific low back pain' was developed in the Netherlands. The current paper describes the design of a study aiming to evaluate the (cost-) effectiveness of a multifaceted strategy to implement this guideline. In a cluster-randomised controlled trial, the (cost-) effectiveness of a multifaceted implementation strategy will be compared to passive guideline dissemination. Using a stepped-wedge approach, participating general practitioners, physiotherapists, and occupational physicians are allocated into clusters and will attend a multidisciplinary continuing medical education training session. The timing these clusters receive the training is the unit of randomisation. LBP patients visiting the participating health care providers are invited to participate in the trial and will receive access to a multimedia intervention aimed at improving beliefs, cognitions, and self-management. The primary outcome measure of this study is patient back beliefs. Secondary outcome measures on patient level include pain, functional status, quality of life, health care utility, and productivity losses. Outcome measures on professional level include knowledge and attitude towards the guideline, and guideline adherence. A process evaluation for the implementation strategy will be performed among the health care providers and the patients. Furthermore, a qualitative subgroup analysis among patients with various ethnic backgrounds will be performed. This study will give insight into the (cost-) effectiveness of a multifaceted implementation strategy for the Dutch multidisciplinary guideline for non

  1. An Overview of NASA's Integrated Design and Engineering Analysis (IDEA) Environment

    Science.gov (United States)

    Robinson, Jeffrey S.

    2011-01-01

    Historically, the design of subsonic and supersonic aircraft has been divided into separate technical disciplines (such as propulsion, aerodynamics and structures), each of which performs design and analysis in relative isolation from others. This is possible, in most cases, either because the amount of interdisciplinary coupling is minimal, or because the interactions can be treated as linear. The design of hypersonic airbreathing vehicles, like NASA's X-43, is quite the opposite. Such systems are dominated by strong non-linear interactions between disciplines. The design of these systems demands that a multi-disciplinary approach be taken. Furthermore, increased analytical fidelity at the conceptual design phase is highly desirable, as many of the non-linearities are not captured by lower fidelity tools. Only when these systems are designed from a true multi-disciplinary perspective, can the real performance benefits be achieved and complete vehicle systems be fielded. Toward this end, the Vehicle Analysis Branch at NASA Langley Research Center has been developing the Integrated Design and Engineering Analysis (IDEA) Environment. IDEA is a collaborative environment for parametrically modeling conceptual and preliminary designs for launch vehicle and high speed atmospheric flight configurations using the Adaptive Modeling Language (AML) as the underlying framework. The environment integrates geometry, packaging, propulsion, trajectory, aerodynamics, aerothermodynamics, engine and airframe subsystem design, thermal and structural analysis, and vehicle closure into a generative, parametric, unified computational model where data is shared seamlessly between the different disciplines. Plans are also in place to incorporate life cycle analysis tools into the environment which will estimate vehicle operability, reliability and cost. IDEA is currently being funded by NASA?s Hypersonics Project, a part of the Fundamental Aeronautics Program within the Aeronautics

  2. Design-based online teacher professional development to introduce integration of STEM in Pakistan

    Science.gov (United States)

    Anwar, Tasneem

    In today's global society where innovations spread rapidly, the escalating focus on science, technology, engineering and mathematics (STEM) has quickly intensified in the United States, East Asia and much of Western Europe. Our ever-changing, increasingly global society faces many multidisciplinary problems, and many of the solutions require the integration of multiple science, technology, engineering, and mathematics (STEM) concepts. Thus, there is a critical need to explore the integration of STEM subjects in international education contexts. This dissertation study examined the exploration of integration of STEM in the unique context of Pakistan. This study used three-phase design-based methodological framework derived from McKenney and Reeves (2012) to explore the development of a STEM focused online teacher professional development (oTPD-STEM) and to identify the design features that facilitate teacher learning. The oTPD-STEM program was designed to facilitate eight Pakistani elementary school teachers' exploration of the new idea of STEM integration through both practical and theoretical considerations. This design-based study employed inductive analysis (Strauss and Corbin, 1998) to analyze multiple data sources of interviews, STEM perception responses, reflective learning team conversations, pre-post surveys and artifacts produced in oTPD-STEM. Findings of this study are presented as: (1) design-based decisions for oTPD-STEM, and (2) evolution in understanding of STEM by sharing participant teachers' STEM model for Pakistani context. This study advocates for the potential of school-wide oTPD for interdisciplinary collaboration through support for learner-centered practices.

  3. Cooling water systems design using process integration

    CSIR Research Space (South Africa)

    Gololo, KV

    2010-09-01

    Full Text Available Cooling water systems are generally designed with a set of heat exchangers arranged in parallel. This arrangement results in higher cooling water flowrate and low cooling water return temperature thus reducing cooling tower efficiency. Previous...

  4. Design Tools for Integrated Asynchronous Electronic Circuits

    National Research Council Canada - National Science Library

    Martin, Alain

    2003-01-01

    ..., simulation, verification, at the logical and physical levels. Situs has developed a business model for the commercialization of the CAD tools, and has designed the prototype of the tool suite based on this business model and the Caltech approach...

  5. Integrated Approach to Industrial Packaging Design

    Science.gov (United States)

    Vorobeva, O.

    2017-11-01

    The article reviews studies in the field of industrial packaging design. The major factors which influence technological, ergonomic, economic and ecological features of packaging are established. The main modern trends in packaging design are defined, the principles of marketing communications and their influence on consumers’ consciousness are indicated, and the function of packaging as a transmitter of brand values is specified. Peculiarities of packaging technology and printing techniques in modern printing industry are considered. The role of designers in the stage-by-stage development of the construction, form and graphic design concept of packaging is defined. The examples of authentic packaging are given and the mention of the tetrahedron packaging history is made. At the end of the article, conclusions on the key research aspects are made.

  6. Integration of MGDS design into the licensing process

    International Nuclear Information System (INIS)

    1997-12-01

    This paper presents an overview of how the Mined Geologic Disposal System (MGDS) design for a potential repository is integrated into the licensing process. The integration process employs a two-told approach: (1) ensure that the MGDS design complies with applicable Nuclear Regulatory Commission (NRC) licensing requirements, and (2) ensure that the MGDS design is appropriately reflected in a license application that is acceptable to the NRC for performing acceptance and compliance reviews

  7. Design of Integrated Circuits Approaching Terahertz Frequencies

    OpenAIRE

    Yan, Lei; Johansen, Tom Keinicke

    2013-01-01

    In this thesis, monolithic microwave integrated circuits(MMICs) are presented for millimeter-wave and submillimeter-wave or terahertz(THz) applications. Millimeter-wave power generation from solid state devices is not only crucial for the emerging high data rate wireless communications but also important for driving THz signal sources. To meet the requirement of high output power, amplifiers based on InP double heterojunction bipolar transistor (DHBT) devices from the III-V Lab in Marcoussic,...

  8. Integrated circuits, and design and manufacture thereof

    Science.gov (United States)

    Auracher, Stefan; Pribbernow, Claus; Hils, Andreas

    2006-04-18

    A representation of a macro for an integrated circuit layout. The representation may define sub-circuit cells of a module. The module may have a predefined functionality. The sub-circuit cells may include at least one reusable circuit cell. The reusable circuit cell may be configured such that when the predefined functionality of the module is not used, the reusable circuit cell is available for re-use.

  9. Integrated Design Tools for Embedded Control Systems

    OpenAIRE

    Jovanovic, D.S.; Hilderink, G.H.; Broenink, Johannes F.; Karelse, F.

    2001-01-01

    Currently, computer-based control systems are still being implemented using the same techniques as 10 years ago. The purpose of this project is the development of a design framework, consisting of tools and libraries, which allows the designer to build high reliable heterogeneous real-time embedded systems in a very short time at a fraction of the present day costs. The ultimate focus of current research is on transformation control laws to efficient concurrent algorithms, with concerns about...

  10. Safety design integrated in the building delivery system

    DEFF Research Database (Denmark)

    Jørgensen, Kirsten

    2013-01-01

    . The purpose of this article is to demonstrate how safety and health can be integrated in the design phases integrated in the management delivery systems within construction, The method for the research was to go through the building delivery system step by step and create a normative description of what, when......In construction, it is important to view safety and health as an integrated part of the way that “designers” are working. The designers cowers architects, constructors, engineers and others who carry out their consulting services in the design phase of a construction project. The philosophy...... and how to fully integrate safety in each part of the process. The result is a concept and guideline including control forms for how to integrate safety design in the Building Delivery System plus what to do and when. The concept has been tested in an educational context. The practical value...

  11. Novel integrated design framework for radio frequency quadrupoles

    International Nuclear Information System (INIS)

    Jolly, Simon; Easton, Matthew; Lawrie, Scott; Letchford, Alan; Pozimski, Jürgen; Savage, Peter

    2014-01-01

    A novel design framework for Radio Frequency Quadrupoles (RFQs), developed as part of the design of the FETS RFQ, is presented. This framework integrates several previously disparate steps in the design of RFQs, including the beam dynamics design, mechanical design, electromagnetic, thermal and mechanical modelling and beam dynamics simulations. Each stage of the design process is described in detail, including the various software options and reasons for the final software suite selected. Results are given for each of these steps, describing how each stage affects the overall design process, with an emphasis on the resulting design choices for the FETS RFQ

  12. Integrating 3D modeling, photogrammetry and design

    CERN Document Server

    Foster, Shaun

    2014-01-01

    This book looks at the convergent nature of technology and its relationship to the field of photogrammetry and 3D design. This is a facet of a broader discussion of the nature of technology itself and the relationship of technology to art, as well as an examination of the educational process. In the field of technology-influenced design-based education it is natural to push for advanced technology, yet within a larger institution the constraints of budget and adherence to tradition must be accepted. These opposing forces create a natural balance; in some cases constraints lead to greater creat

  13. Integrated Energy Design in Master Planning

    DEFF Research Database (Denmark)

    Strømann-Andersen, Jakob Bjørn

    This PhD thesis considers urban structure and buildings in an energy correlation and use the knowledge to design energy- and comfort-optimized cities and buildings. The parameters are: the structure of nature, the city and the landscape, both in terms of geometry and interrelationships and in terms...... in character as daylight is taken into account. Furthermore the results suggest that there are limits to urban densification (200-300%) as an energy optimization strategy. The solar energy and daylight potential should be considered, and indeed protected, as a common resource in urban design. The most...

  14. On the Integration of Digital Design and Analysis Tools

    DEFF Research Database (Denmark)

    Klitgaard, Jens; Kirkegaard, Poul Henning

    2006-01-01

    The aim of this research is to look into integrated digital design and analysis tools in order to find out if it is suited for use by architects and designers or only by specialists and technicians - and if not, then to look at what can be done to make them more available to architects and design...

  15. High School Engineering and Technology Education Integration through Design Challenges

    Science.gov (United States)

    Mentzer, Nathan

    2011-01-01

    This study contextualized the use of the engineering design process by providing descriptions of how each element in a design process was integrated in an eleventh grade industry and engineering systems course. The guiding research question for this inquiry was: How do students engage in the engineering design process in a course where technology…

  16. Model reduction in integrated controls-structures design

    Science.gov (United States)

    Maghami, Peiman G.

    1993-01-01

    It is the objective of this paper to present a model reduction technique developed for the integrated controls-structures design of flexible structures. Integrated controls-structures design problems are typically posed as nonlinear mathematical programming problems, where the design variables consist of both structural and control parameters. In the solution process, both structural and control design variables are constantly changing; therefore, the dynamic characteristics of the structure are also changing. This presents a problem in obtaining a reduced-order model for active control design and analysis which will be valid for all design points within the design space. In other words, the frequency and number of the significant modes of the structure (modes that should be included) may vary considerably throughout the design process. This is also true as the locations and/or masses of the sensors and actuators change. Moreover, since the number of design evaluations in the integrated design process could easily run into thousands, any feasible order-reduction method should not require model reduction analysis at every design iteration. In this paper a novel and efficient technique for model reduction in the integrated controls-structures design process, which addresses these issues, is presented.

  17. Design Thinking: Employing an Effective Multidisciplinary Pedagogical Framework to Foster Creativity and Innovation in Rural and Remote Education

    Science.gov (United States)

    Anderson, Neil

    2012-01-01

    This paper outlines a project to develop and track "design thinking" skills within groups of students in late primary and early secondary years of schooling in order to strengthen their creative skills and innovative mindsets. The outcome of the research will be the development of a model for the broad-based implementation of design…

  18. Food product design. An integrated approach

    NARCIS (Netherlands)

    Linnemann, A.R.; Boekel, van M.A.J.S.

    2007-01-01

    This book explains how to apply barrier technology in food production to improve product stability and the possibilities of modelling and statistics in food product design are elaborated. Attention is given to Life Cycle Assessment as a method to determine the environmental impact of a food from

  19. Thinking Tracks for Integrated Systems Design

    NARCIS (Netherlands)

    Bonnema, Gerrit Maarten; Denkena, B.; Gausemeijer, J.; Scholz-Reiter, B.

    2012-01-01

    The paper investigates systems thinking and systems engineering. After a short literature review, the paper presents, as a means for systems thinking, twelve thinking tracks. The tracks can be used as creativity starter, checklist, and as means to investigate effects of design decisions taken early

  20. Integration of Design and Control through Model Analysis

    DEFF Research Database (Denmark)

    Russel, Boris Mariboe; Henriksen, Jens Peter; Jørgensen, Sten Bay

    2002-01-01

    A systematic computer aided analysis of the process model is proposed as a pre-solution step for integration of design and control problems. The process model equations are classified in terms of balance equations, constitutive equations and conditional equations. Analysis of the phenomena models...... (structure selection) issues for the integrated problems are considered. (C) 2002 Elsevier Science Ltd. All rights reserved....... representing the constitutive equations identify the relationships between the important process and design variables, which help to understand, define and address some of the issues related to integration of design and control. Furthermore, the analysis is able to identify a set of process (control) variables...

  1. Multidisciplinary outpatient care program for patients with chronic low back pain: design of a randomized controlled trial and cost-effectiveness study [ISRCTN28478651

    Directory of Open Access Journals (Sweden)

    Anema Johannes R

    2007-09-01

    Full Text Available Abstract Background Chronic low back pain (LBP is a major public and occupational health problem, which is associated with very high costs. Although medical costs for chronic LBP are high, most costs are related to productivity losses due to sick leave. In general, the prognosis for return to work (RTW is good but a minority of patients will be absent long-term from work. Research shows that work related problems are associated with an increase in seeking medical care and sick leave. Usual medical care of patients is however, not specifically aimed at RTW. The objective is to present the design of a randomized controlled trial, i.e. the BRIDGE-study, evaluating the effectiveness in improving RTW and cost-effectiveness of a multidisciplinary outpatient care program situated in both primary and outpatient care setting compared with usual clinical medical care for patients with chronic LBP. Methods/Design The design is a randomized controlled trial with an economic evaluation alongside. The study population consists of patients with chronic LBP who are completely or partially sick listed and visit an outpatient clinic of one of the participating hospitals in Amsterdam (the Netherlands. Two interventions will be compared. 1. a multidisciplinary outpatient care program consisting of a workplace intervention based on participatory ergonomics, and a graded activity program using cognitive behavioural principles. 2. usual care provided by the medical specialist, the occupational physician, the patient's general practitioner and allied health professionals. The primary outcome measure is sick leave duration until full RTW. Sick leave duration is measured monthly by self-report during one year. Data on sick leave during one-year follow-up are also requested form the employers. Secondary outcome measures are pain intensity, functional status, pain coping, patient satisfaction and quality of life. Outcome measures are assessed before randomization and 3, 6

  2. Workspace design: Integrating ergonomics into the design of production systems

    DEFF Research Database (Denmark)

    Broberg, Ole

    2006-01-01

    The work practice of ergonomists in workplace-making processes was studied by a socio-technical framework. This resulted in the term ‘political reflective navigator’ as a conceptualization of the identified work practice and competencies. In order to strengthen the impact of ergonomists it was fo......The work practice of ergonomists in workplace-making processes was studied by a socio-technical framework. This resulted in the term ‘political reflective navigator’ as a conceptualization of the identified work practice and competencies. In order to strengthen the impact of ergonomists...... it was found that new ways and tools for influencing the design of production systems are needed. The concept of workspace design and ‘staging the workspace design’ is suggested as a new framework for seeing and guiding ergonomists when taking part in design of workplaces and production systems....

  3. MICRO & NANO TECHNOLOGIES – APPLICATIONS, DESIGN AND INTEGRATION

    Directory of Open Access Journals (Sweden)

    Dorin LEŢ

    2010-05-01

    Full Text Available The science of micro-nano technologies represents a multidisciplinary research domain, which provokes active participation of specialist from multiple domains (physics, chemistry, biology, mathematics, electronics, medicine, a.o.. Nanotechnology is an applied science domain focusing the design, synthesis and characterization of materials and devices starting from individual atoms and molecules level up to supramolecular level of strains of molecules with 100 molecular diameters. Operations at this dimensions implies the understanding of new scientific principles and new materials properties, which take place at micro and nano scale and are used in the development of materials, devices and systems with new and improved functions and performances. The properties and basic functions of structures and material systems at nano scale may be changed based on the organization of the living mater on molecular “weak” interactions (hydrogen binds, electrostatic dipole, Van der Waals forces, surface forces, electrofluidic forces, a.o..

  4. Blue green component and integrated urban design

    Directory of Open Access Journals (Sweden)

    Stanković Srđan M.

    2016-01-01

    Full Text Available This paper aims to demonstrate the hidden potential of blue green components, in a synergetic network, not as separate systems, like used in past. The innovative methodology of the project Blue Green Dream is presented through examples of good practice. A new approach in the project initiate thoughtful planning and remodeling of the settlement for the modern man. Professional and scientific public is looking for way to create more healthy and stimulating place for living. However, offered integrative solutions still remain out of urban and architectural practice. Tested technologies in current projects confirmed measurability of innovative approaches and lessons learned. Scientific and professional contributions are summarized in master's and doctoral theses that have been completed or are in process of writing.

  5. Slide layout and integrated design (SLIDE) program

    International Nuclear Information System (INIS)

    Roberts, S.G.

    1975-01-01

    SLIDE is a FORTRAN IV program for producing 35 mm color slides on the Control Data CYBER-74. SLIDE interfaces with the graphics package, DISSPLA, on the CYBER-74. It was designed so that persons with no previous computer experience can easily and quickly generate their own textual 35 mm color slides for verbal presentations. SLIDE's features include seven different colors, five text sizes, ten tab positions, and two page sizes. As many slides as desired may be produced during any one run of the program. Each slide is designed to represent an 8 1 / 2 in. x 11 in. or an 11 in. x 8 1 / 2 in. page. The input data cards required to run the SLIDE program and the program output are described. Appendixes contain a sample program run showing input, output, and the resulting slides produced and a FORTRAN listing of the SLIDE program. (U.S.)

  6. X-traktor: A Rookie Robot, Simple, Yet Complex, Impeccably Designed, a Very Innovative Multidisciplinary Engineering Masterpiece

    Science.gov (United States)

    Henderson, A. J., Jr.

    2001-01-01

    FIRST is the acronym of For Inspiration and Recognition of Science and Technology. FIRST is a 501.C.3 non-profit organization whose mission is to generate an interest in science and engineering among today's young adults and youth. This mission is accomplished through a robot competition held annually in the spring of each year. NASAs Marshall Space Flight Center, Education Programs Department, awarded a grant to Lee High School, the sole engineering magnet school in Huntsville, Alabama. MSFC awarded the grant in hopes of fulfilling its goal of giving back invaluable resources to its community and engineers, as well as educating tomorrow's work force in the high-tech area of science and technology. Marshall engineers, Lee High School students and teachers, and a host of other volunteers and parents officially initiated this robot design process and competitive strategic game plan. The FIRST Robotics Competition is a national engineering contest, which immerses high school students in the exciting world of science and engineering. Teaming with engineers from government agencies, businesses, and universities enables the students to learn about the engineering profession. The students and engineers have six weeks to work together to brainstorm, design, procure, construct, and test their robot. The team then competes in a spirited, 'no-holds barred' tournament, complete with referees, other FIRST-designed robots, cheerleaders, and time clocks. The partnerships developed between schools, government agencies, businesses, and universities provide an exchange of resources and talent that build cooperation and expose students to new and rewarding career options. The result is a fun, exciting, and stimulating environment in which all participants discover the important connections between classroom experiences and real-world applications. This paper will highlight the story, engineering development, and evolutionary design of Xtraktor, the rookie robot, a manufacturing

  7. Methodology for sensitivity analysis, approximate analysis, and design optimization in CFD for multidisciplinary applications. [computational fluid dynamics

    Science.gov (United States)

    Taylor, Arthur C., III; Hou, Gene W.

    1992-01-01

    Fundamental equations of aerodynamic sensitivity analysis and approximate analysis for the two dimensional thin layer Navier-Stokes equations are reviewed, and special boundary condition considerations necessary to apply these equations to isolated lifting airfoils on 'C' and 'O' meshes are discussed in detail. An efficient strategy which is based on the finite element method and an elastic membrane representation of the computational domain is successfully tested, which circumvents the costly 'brute force' method of obtaining grid sensitivity derivatives, and is also useful in mesh regeneration. The issue of turbulence modeling is addressed in a preliminary study. Aerodynamic shape sensitivity derivatives are efficiently calculated, and their accuracy is validated on two viscous test problems, including: (1) internal flow through a double throat nozzle, and (2) external flow over a NACA 4-digit airfoil. An automated aerodynamic design optimization strategy is outlined which includes the use of a design optimization program, an aerodynamic flow analysis code, an aerodynamic sensitivity and approximate analysis code, and a mesh regeneration and grid sensitivity analysis code. Application of the optimization methodology to the two test problems in each case resulted in a new design having a significantly improved performance in the aerodynamic response of interest.

  8. Designing with ethnography : an integrative approach to CSCW design

    NARCIS (Netherlands)

    Iqbal, Rahat; James, A.; Gatward, R.

    2005-01-01

    This paper presents a part of wider research endeavor within the field of Computer Supported Cooperative Work (CSCW) to leverage the use of ethnography for systems design. It investigates the role of ethnography in the development of CSCW systems and its relevance to real world problems,

  9. The difference in communication between architects and engineers and the effectiveness within integral design

    NARCIS (Netherlands)

    Zeiler, W.; Bohemia, E.; Eger, A.; Eggink, W.; Kovacevic, A.; Parkinson, B.; Wits, W.

    2014-01-01

    Within the building industry there is a clear need for more sustainable solutions, with as ultimate goal energy positive buildings. This makes building design more complex. Building design transfers from a mainly architect led process into a multi-disciplinary design team process to cope with the

  10. Strategic Mobility 21: Integrated Tracking System Analysis and Concept Design

    National Research Council Canada - National Science Library

    Mallon, Lawrence G; Savacool, Edwin

    2007-01-01

    .... This design document supports the SM21 efforts in developing a dual-use multi-modal node at the Southern California Logistics Airport in Victorville, CA that will be supported by an Integrated Tracking System...

  11. Sensitivity Analysis for Design Optimization Integrated Software Tools, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — The objective of this proposed project is to provide a new set of sensitivity analysis theory and codes, the Sensitivity Analysis for Design Optimization Integrated...

  12. On the logistics effects of integrated product and package design

    DEFF Research Database (Denmark)

    Bramklev, Caroline; Hansen, Claus Thorp

    2007-01-01

    obtaining error-free deliveries, saving costs and avoiding quality problems. Thus, the authors of this paper see a challenge in developing the theory and methodology for Integrated Product and Package Design. In this paper we take a first step in this direction. Firstly, we have carried out a broad review...... of literature, which shows that there is a need for research into Integrated Product and Package Design. Secondly, we have analysed three cases from industrial practice, which show that a conscious and integrated design of product and package has positive logistics effects, whereas neglecting this issue might...... result in higher costs and quality problems. On the basis of these cases we have made an initial cross-case analysis, which indicates that it is possible to develop the terminology and methodology for Integrated Product and Package Design....

  13. Integration of case study approach, project design and computer ...

    African Journals Online (AJOL)

    Integration of case study approach, project design and computer modeling in managerial accounting education ... Journal of Fundamental and Applied Sciences ... in the Laboratory of Management Accounting and Controlling Systems at the ...

  14. Conceptual design of main coolant pump for integral reactor SMART

    Energy Technology Data Exchange (ETDEWEB)

    Park, Jin Seok; Kim, Jong In; Kim, Min Hwan [Korea Atomic Energy Research Institute, Taejon (Korea)

    1999-12-01

    The conceptual design for MCP to be installed in the integral reactor SMART was carried out. Canned motor pump was adopted in the conceptual design of MCP. Three-dimensional modeling was performed to visualize the conceptual design of the MCP and to check interferences between the parts. The theoretical design procedure for the impeller was developed. The procedures for the flow field and structural analysis of impeller was also developed to assess the design validity and to verify its structural integrity. A computer program to analyze the dynamic characteristics of the rotor shaft of MCP was developed. The rotational speed sensor was designed and its performance test was conducted to verify the possibility of operation. A prototypes of the canned motor was manufactured and tested to confirm the validity of the design concept. The MCP design concept was also investigated for fabricability by establishing the manufacturing procedures. 41 refs., 96 figs., 10 tabs. (Author)

  15. Design dis-integration Silent, Partial, and Disparate Design

    OpenAIRE

    Stevens, John; Moultrie, James; Crilly, Nathan

    2009-01-01

    Michael Porter’s frameworks for analysing and planning competitive differentiation (Porter 1980, 1985) are established ‘textbook’ tools, widely taught to business students today. As the claim of design’s strategic importance is increasingly heard, we ask where does design fit in established strategy thinking? This paper documents a proposed conceptual model based on Porter’s value chain model for strategic planning. The concept outlined is the result of the first stage of a larger study of ...

  16. Implementing Integrated Multicultural Instructional Design in Management Education

    Science.gov (United States)

    Schultz, Jennifer L.; Higbee, Jeanne L.

    2011-01-01

    This purpose of this paper is to summarize the principles of integrated multicultural instructional design (IMID; Higbee, Goff, & Schultz, in press; Higbee, Schultz, & Goff, 2010) and present specific strategies for incorporating IMID in management education. The primary goal of IMID is to promote the integration of multicultural content…

  17. Integrated structure/control design - Present methodology and future opportunities

    Science.gov (United States)

    Weisshaar, T. A.; Newsom, J. R.; Zeiler, T. A.; Gilbert, M. G.

    1986-01-01

    Attention is given to current methodology applied to the integration of the optimal design process for structures and controls. Multilevel linear decomposition techniques proved to be most effective in organizing the computational efforts necessary for ISCD (integrated structures and control design) tasks. With the development of large orbiting space structures and actively controlled, high performance aircraft, there will be more situations in which this concept can be applied.

  18. Study on integrated design and analysis platform of NPP

    International Nuclear Information System (INIS)

    Lu Dongsen; Gao Zuying; Zhou Zhiwei

    2001-01-01

    Many calculation software have been developed to nuclear system's design and safety analysis, such as structure design software, fuel design and manage software, thermal hydraulic analysis software, severe accident simulation software, etc. This study integrates those software to a platform, develops visual modeling tool for Retran, NGFM90. And in this platform, a distribution calculation method is also provided for couple calculation between different software. The study will improve the design and analysis of NPP

  19. Engineering and industrial design : an integrated interdisciplinary design theory

    OpenAIRE

    Brezing, Alexander Nikolaus; Löwer, Manuel

    2009-01-01

    It is generally accepted that superior products result from a balanced consideration of both “technology” and “aesthetic design”. Nonetheless, the gap between the two professions of the “design engineer“ and the “industrial designer“ has not been bridged since their origination in the course of industrialization [7]. One possible approach to enhance the collaboration of both disciplines is to teach the basics of the respective other’s. In Germany, the main work following this approach of tryi...

  20. Multidisciplinary System Reliability Analysis

    Science.gov (United States)

    Mahadevan, Sankaran; Han, Song; Chamis, Christos C. (Technical Monitor)

    2001-01-01

    The objective of this study is to develop a new methodology for estimating the reliability of engineering systems that encompass multiple disciplines. The methodology is formulated in the context of the NESSUS probabilistic structural analysis code, developed under the leadership of NASA Glenn Research Center. The NESSUS code has been successfully applied to the reliability estimation of a variety of structural engineering systems. This study examines whether the features of NESSUS could be used to investigate the reliability of systems in other disciplines such as heat transfer, fluid mechanics, electrical circuits etc., without considerable programming effort specific to each discipline. In this study, the mechanical equivalence between system behavior models in different disciplines are investigated to achieve this objective. A new methodology is presented for the analysis of heat transfer, fluid flow, and electrical circuit problems using the structural analysis routines within NESSUS, by utilizing the equivalence between the computational quantities in different disciplines. This technique is integrated with the fast probability integration and system reliability techniques within the NESSUS code, to successfully compute the system reliability of multidisciplinary systems. Traditional as well as progressive failure analysis methods for system reliability estimation are demonstrated, through a numerical example of a heat exchanger system involving failure modes in structural, heat transfer and fluid flow disciplines.

  1. Multidisciplinary Computational Research

    National Research Council Canada - National Science Library

    Visbal, Miguel R

    2006-01-01

    The purpose of this work is to develop advanced multidisciplinary numerical simulation capabilities for aerospace vehicles with emphasis on highly accurate, massively parallel computational methods...

  2. Integration of rocket turbine design and analysis through computer graphics

    Science.gov (United States)

    Hsu, Wayne; Boynton, Jim

    1988-01-01

    An interactive approach with engineering computer graphics is used to integrate the design and analysis processes of a rocket engine turbine into a progressive and iterative design procedure. The processes are interconnected through pre- and postprocessors. The graphics are used to generate the blade profiles, their stacking, finite element generation, and analysis presentation through color graphics. Steps of the design process discussed include pitch-line design, axisymmetric hub-to-tip meridional design, and quasi-three-dimensional analysis. The viscous two- and three-dimensional analysis codes are executed after acceptable designs are achieved and estimates of initial losses are confirmed.

  3. Integral design small nuclear power plant UNITHERM

    International Nuclear Information System (INIS)

    Adamovich, L. A.; Grechko, G. I.; Ulasevich, V. K.; Shishkin, V. A.

    1995-01-01

    The need to erect expensive energy transmission lines to these places demands to use independent local energy sources. Therefore, a reasonable alternative to the plants fired fossil fuel, mostly hydrocarbon fuel, may come from the nuclear power plants (NPP) of relatively small capacity which are nonattended, shipped to the site by large-assembled modules and completely withdrawable from the site during decommissioning. Application of NPPs for power and heat supply may prove to be cost-efficient and rather positive from social and ecological point of view. UNITHERM NPP belongs to such energy sources and may be used for heat and power supply. Heat can be provided both as hot water and superheated steam. The consumers are able to specify heat/energy supply ratio. NPP design provides for independent energy supply to the consumers and the possibility to disconnect each of them without disruption of operation of the others. Thermal hydraulic diagram of UNITHERM NPP provides for the use of three interconnected, process circuits. The consumers of thermal energy (turbogenerator unit and boilers of the central heating unit) are arranged in the last circuit

  4. How to integrate geology, biology, and modern wireless technologies to assess biotic-abiotic interactions on coastal dune systems: a new multidisciplinary approach

    Science.gov (United States)

    Sarti, Giovanni; Bertoni, Duccio; Bini, Monica; Ciccarelli, Daniela; Ribolini, Adriano; Ruocco, Matteo; Pozzebon, Alessandro; Alquini, Fernanda; Giaccari, Riccardo; Tordella, Stefano

    2014-05-01

    Coastal dune systems are arguably one of the most dynamic environments because their evolution is controlled by many factors, both natural and human-related. Hence, they are often exposed to processes leading to erosion, which in turn determine serious naturalistic and economic losses. Most recent studies carried out on different dune fields worldwide emphasized the notion that a better definition of this environment needs an approach that systematically involves several disciplines, striving to merge every data collected from any individual analyses. Therefore, a new multidisciplinary method to study coastal dune systems has been conceived in order to integrate geology, biology, and modern wireless technologies. The aim of the work is threefold: i) to check the reliability of this new approach; ii) to provide a dataset as complete as ever about the factors affecting the evolution of coastal dunes; and iii) to evaluate the influence of any biotic and abiotic factors on plant communities. The experimentation site is located along the Pisa coast within the Migliarino - S. Rossore - Massaciuccoli Regional Park, a protected area where human influence is low (Tuscany, Italy). A rectangle of 100 x 200 m containing 50 grids of 20 x 20 m was established along the coastal dune systems from the coastline to the pinewood at the landward end of the backdune area. Sampling from each grid determined grain-size analysis carried out on surface sediment samples such as geologic aspects; topographic surveys performed by means of DGPS-RTK instruments; geophysical surveys conducted with a GPR equipment, which will be matched with core drilling activities; digital image analysis of high definition pictures taken by means of a remote controlled aircraft drone flying over the study area; biological data obtained by percent cover of each vascular plant species recorded in the sampling unit. Along with geologic and biologic methodologies, this research implemented the use of informatics

  5. Development of integrated platform for computational material design

    Energy Technology Data Exchange (ETDEWEB)

    Kiyoshi, Matsubara; Kumi, Itai; Nobutaka, Nishikawa; Akifumi, Kato [Center for Computational Science and Engineering, Fuji Research Institute Corporation (Japan); Hideaki, Koike [Advance Soft Corporation (Japan)

    2003-07-01

    The goal of our project is to design and develop a problem-solving environment (PSE) that will help computational scientists and engineers develop large complicated application software and simulate complex phenomena by using networking and parallel computing. The integrated platform, which is designed for PSE in the Japanese national project of Frontier Simulation Software for Industrial Science, is defined by supporting the entire range of problem solving activity from program formulation and data setup to numerical simulation, data management, and visualization. A special feature of our integrated platform is based on a new architecture called TASK FLOW. It integrates the computational resources such as hardware and software on the network and supports complex and large-scale simulation. This concept is applied to computational material design and the project 'comprehensive research for modeling, analysis, control, and design of large-scale complex system considering properties of human being'. Moreover this system will provide the best solution for developing large and complicated software and simulating complex and large-scaled phenomena in computational science and engineering. A prototype has already been developed and the validation and verification of an integrated platform will be scheduled by using the prototype in 2003. In the validation and verification, fluid-structure coupling analysis system for designing an industrial machine will be developed on the integrated platform. As other examples of validation and verification, integrated platform for quantum chemistry and bio-mechanical system are planned.

  6. Development of integrated platform for computational material design

    International Nuclear Information System (INIS)

    Kiyoshi, Matsubara; Kumi, Itai; Nobutaka, Nishikawa; Akifumi, Kato; Hideaki, Koike

    2003-01-01

    The goal of our project is to design and develop a problem-solving environment (PSE) that will help computational scientists and engineers develop large complicated application software and simulate complex phenomena by using networking and parallel computing. The integrated platform, which is designed for PSE in the Japanese national project of Frontier Simulation Software for Industrial Science, is defined by supporting the entire range of problem solving activity from program formulation and data setup to numerical simulation, data management, and visualization. A special feature of our integrated platform is based on a new architecture called TASK FLOW. It integrates the computational resources such as hardware and software on the network and supports complex and large-scale simulation. This concept is applied to computational material design and the project 'comprehensive research for modeling, analysis, control, and design of large-scale complex system considering properties of human being'. Moreover this system will provide the best solution for developing large and complicated software and simulating complex and large-scaled phenomena in computational science and engineering. A prototype has already been developed and the validation and verification of an integrated platform will be scheduled by using the prototype in 2003. In the validation and verification, fluid-structure coupling analysis system for designing an industrial machine will be developed on the integrated platform. As other examples of validation and verification, integrated platform for quantum chemistry and bio-mechanical system are planned

  7. Electronic medical history designed by a multidisciplinary unit mastology; Historia clinica electronica disenada por una unidad de mastologia multidisciplinaria

    Energy Technology Data Exchange (ETDEWEB)

    Camejo, N.; Castillo, C.; Vaca, N.; Camargo, B.; Artagaveytia, N.; Acuna, S.; Milans, S.; Lavina, G.; Carzoglio, J.; Jacobo, O.; Pressa, C.; Delgado, L. [Servicio de Oncologia, Hospital de Clinicas, Montevideo (Uruguay)

    2012-11-15

    Full text: Objective: To facilitate the collection, organization and analysis of data from patients Unit assisted in Mastology by producing an electronic health record. Materials and Methods: We evaluated forms provided by medical oncologists, radio therapists, radiologists, pathologists, and plastic surgeons mastologists collect data interrogation, physical examination, complementary examinations, diagnoses, anatomy pathological evolution and treatment instituted and generating the system was computerized {sup U}nit Mastology - Electronic Health Record ( UMAHCE){sup .} Results: The story was designed in modules that collect data on instances arising diagnostic, treatment and monitoring of patients. Each module is represented by an icon that changes color to enter data, allowing the objectify doctor if they are or not the data for that module. The system can attach images recorded by breast exam photos, photos of study, imaging (mammography, CT, MRI) in the same way that the surgeon to enter the protocol surgical or anatomical pathologist enter a pathological report of a study untimely or after definitive surgery. The system can generate an automatic report of the input data that can be printed and placed in the patient's medical history. It also can generate the e mail alerts doctors on pathological results were entered into regarding the diagnosis or treatment breast cancer (eg, mammography B I-Rads 4 or 5, report positive cytologic puncture malignancy, H R and Her status). Conclusions: We developed an electronic medical record that allows different doctors involved in the management of breast disease can be accessed through the web regardless of where they are ( pathology laboratory, room radiology reports, clinic, operation theater), both for information about a patient to enter data the same in relation to their specialty. Moreover, homogenize manages the type and quality of the data and therefore can improve the care and research activities as well as

  8. TECNOB: study design of a randomized controlled trial of a multidisciplinary telecare intervention for obese patients with type-2 diabetes

    Directory of Open Access Journals (Sweden)

    Tuzzi Cristina

    2010-04-01

    Full Text Available Abstract Background Obesity is one of the most important medical and public health problems of our time: it increases the risk of many health complications such as hypertension, coronary heart disease and type 2 diabetes, needs long-lasting treatment for effective results and involves high public and private costs. Therefore, it is imperative that enduring and low-cost clinical programs for obesity and related co-morbidities are developed and evaluated. Methods/Design TECNOB (TEChnology for OBesity is a comprehensive two-phase stepped down program enhanced by telemedicine for the long-term treatment of obese people with type 2 diabetes seeking intervention for weight loss. Its core features are the hospital-based intensive treatment (1-month, that consists of diet therapy, physical training and psychological counseling, and the continuity of care at home using new information and communication technologies (ICT such as internet and mobile phones. The effectiveness of the TECNOB program compared with usual care (hospital-based treatment only will be evaluated in a randomized controlled trial (RCT with a 12-month follow-up. The primary outcome is weight in kilograms. Secondary outcome measures are energy expenditure measured using an electronic armband, glycated hemoglobin, binge eating, self-efficacy in eating and weight control, body satisfaction, healthy habit formation, disordered eating-related behaviors and cognitions, psychopathological symptoms and weight-related quality of life. Furthermore, the study will explore what behavioral and psychological variables are predictive of treatment success among those we have considered. Discussion The TECNOB study aims to inform the evidence-based knowledge of how telemedicine may enhance the effectiveness of clinical interventions for weight loss and related type-2 diabetes, and which type of obese patients may benefit the most from such interventions. Broadly, the study aims also to have a effect on

  9. The Application of Integrated Design System for HTR-PM Design

    International Nuclear Information System (INIS)

    Qi Shi; Xiaojing Kang

    2014-01-01

    SmartPlant Enterprise(SPE) developed by Intergraph from America is a new generation integrated solution for engineering design. Combined with the application in a nuclear engineering, this paper introduced the composition and the data flow of Integrated Design System established by SPE, analyzed the advantages and the insufficiency, and provided the direction of continuous improvement. (author)

  10. Formative Assessment Design for PDA Integrated Ecology Observation

    Science.gov (United States)

    Hung, Pi-Hsia; Lin, Yu-Fen; Hwang, Gwo-Jen

    2010-01-01

    Ubiquitous computing and mobile technologies provide a new perspective for designing innovative outdoor learning experiences. The purpose of this study is to propose a formative assessment design for integrating PDAs into ecology observations. Three learning activities were conducted in this study. An action research approach was applied to…

  11. Integrating ergonomics into engineering design: The role of objects

    DEFF Research Database (Denmark)

    Hall-Andersen, Lene Bjerg; Broberg, Ole

    2014-01-01

    The objective of this study was to explore the role of objects in integrating ergonomic knowledge in engineering design processes. An engineering design case was analyzed using the theoretical concepts of boundary objects and intermediary objects: Boundary objects facilitate collaboration between...

  12. Developing an Integrated Design Strategy for Chip Layout Optimization

    NARCIS (Netherlands)

    Wits, Wessel Willems; Jauregui Becker, Juan Manuel; van Vliet, Frank Edward; te Riele, G.J.

    2011-01-01

    This paper presents an integrated design strategy for chip layout optimization. The strategy couples both electric and thermal aspects during the conceptual design phase to improve chip performances; thermal management being one of the major topics. The layout of the chip circuitry is optimized

  13. Integration of Design and Control Through Model Analysis

    DEFF Research Database (Denmark)

    Russel, Boris Mariboe; Henriksen, Jens Peter; Jørgensen, Sten Bay

    2000-01-01

    of the phenomena models representing the process model identify the relationships between the important process and design variables, which help to understand, define and address some of the issues related to integration of design and control issues. The model analysis is highlighted through examples involving...... processes with mass and/or energy recycle. (C) 2000 Elsevier Science Ltd. All rights reserved....

  14. Design Process for Integrated Concepts with Responsive Building Elements

    DEFF Research Database (Denmark)

    Aa, Van der A.; Heiselberg, Per

    2008-01-01

    An integrated building concept is a prerequisite to come to an energy efficient building with a good and healthy IAQ indoor comfort. A design process that defines the targets and boundary conditions in the very first stage of the design and guarantees them until the building is finished and used...... is needed. The hard question is however: how to make the right choice of the combination of individual measures from building components and building services elements. Within the framework of IEA-ECBCS Annex 44 research has been conducted about the design process for integrated building concepts...

  15. Consequence Based Design. An approach for integrating computational collaborative models (Integrated Dynamic Models) in the building design phase

    DEFF Research Database (Denmark)

    Negendahl, Kristoffer

    relies on various advancements in the area of integrated dynamic models. It also relies on the application and test of the approach in practice to evaluate the Consequence based design and the use of integrated dynamic models. As a result, the Consequence based design approach has been applied in five...... and define new ways to implement integrated dynamic models for the following project. In parallel, seven different developments of new methods, tools and algorithms have been performed to support the application of the approach. The developments concern: Decision diagrams – to clarify goals and the ability...... affect the design process and collaboration between building designers and simulationists. Within the limits of applying the approach of Consequence based design to five case studies, followed by documentation based on interviews, surveys and project related documentations derived from internal reports...

  16. A design approach for integrating thermoelectric devices using topology optimization

    International Nuclear Information System (INIS)

    Soprani, S.; Haertel, J.H.K.; Lazarov, B.S.; Sigmund, O.; Engelbrecht, K.

    2016-01-01

    Highlights: • The integration of a thermoelectric (TE) cooler into a robotic tool is optimized. • Topology optimization is suggested as design tool for TE integrated systems. • A 3D optimization technique using temperature dependent TE properties is presented. • The sensitivity of the optimization process to the boundary conditions is studied. • A working prototype is constructed and compared to the model results. - Abstract: Efficient operation of thermoelectric devices strongly relies on the thermal integration into the energy conversion system in which they operate. Effective thermal integration reduces the temperature differences between the thermoelectric module and its thermal reservoirs, allowing the system to operate more efficiently. This work proposes and experimentally demonstrates a topology optimization approach as a design tool for efficient integration of thermoelectric modules into systems with specific design constraints. The approach allows thermal layout optimization of thermoelectric systems for different operating conditions and objective functions, such as temperature span, efficiency, and power recovery rate. As a specific application, the integration of a thermoelectric cooler into the electronics section of a downhole oil well intervention tool is investigated, with the objective of minimizing the temperature of the cooled electronics. Several challenges are addressed: ensuring effective heat transfer from the load, minimizing the thermal resistances within the integrated system, maximizing the thermal protection of the cooled zone, and enhancing the conduction of the rejected heat to the oil well. The design method incorporates temperature dependent properties of the thermoelectric device and other materials. The 3D topology optimization model developed in this work was used to design a thermoelectric system, complete with insulation and heat sink, that was produced and tested. Good agreement between experimental results and

  17. System 80+ integrated design of a complete plant

    International Nuclear Information System (INIS)

    Turk, R.S.; Stamm, S.L.; Fox, W.A.

    1992-01-01

    In 1985, ABB-Combustion Engineering Nuclear Power (ABB-CENP) and elements of Duke Power Company [now Duke Engineering ampersand Services (DE ampersand S)] joined forces under the aegis of the Electric Power Research Institute (EPRI) Advanced Light Water Reactor (ALWR) Program to develop, with the sponsoring utilities, the design requirements for the next generation of nuclear power plants. With support from the US Department of Energy, ABB-CENP and DE ampersand S again teamed up the following year to initiate a project to design and license the System 80+ standard plant design, an advanced pressurized water reactor that meets these utility requirements. A distinguishing feature of the System 80+ standard design is that it is an essentially complete plant, predesigned and prelicensed to ensure rapid and economical construction. This is in stark contrast to typical prior conduct, where the reactor vendor offered only the nuclear steam supply system and the plant was built on a design-as-you-go basis with constant pressure to release individual elements of the plant design for construction or procurement as soon as possible. Now, however, the design process can be integrated over the total plant, ensuring that the goals set for ALWRs can be met. This integrated design process is manifested in several ways: (1) broad-based participation during the design process by involving designers, analysts, suppliers, constructors, and operators; (2) use of probabilistic risk assessment (PRA) as a design tool to aid in evaluating design features on a total-plant basis; (3) application of human factors engineering methods to a total plant distributed control system to improve the human-machine interface in the design; and (4) use of computer-aided design to enhance assessment of interactions and impacts of all aspects of the total plant. Each of these aspects of integrated plant design is discussed in this paper

  18. Development of core design and analyses technology for integral reactor

    Energy Technology Data Exchange (ETDEWEB)

    Zee, Sung Quun; Lee, C. C.; Song, J. S. and others

    1999-03-01

    Integral reactors are developed for the applications such as sea water desalination, heat energy for various industries, and power sources for large container ships. In order to enhance the inherent and passive safety features, low power density concept is chosen for the integral reactor SMART. Moreover, ultra-longer cycle and boron-free operation concepts are reviewed for better plant economy and simple design of reactor system. Especially, boron-free operation concept brings about large difference in core configurations and reactivity controls from those of the existing large size commercial nuclear power plants and also causes many differences in the safety aspects. The ultimate objectives of this study include detailed core design of a integral reactor, development of the core design system and technology, and finally acquisition of the system design certificate. The goal of the first stage is the conceptual core design, that is, to establish the design bases and requirements suitable for the boron-free concept, to develop a core loading pattern, to analyze the nuclear, thermal and hydraulic characteristics of the core and to perform the core shielding design. Interface data for safety and performance analyses including fuel design data are produced for the relevant design analysis groups. Nuclear, thermal and hydraulic, shielding design and analysis code systems necessary for the core conceptual design are established through modification of the existing design tools and newly developed methodology and code modules. Core safety and performance can be improved by the technology development such as boron-free core optimization, advaned core monitoring and operational aid system. Feasiblity study on the improvement of the core protection and monitoring system will also contribute toward core safety and performance. Both the conceptual core design study and the related technology will provide concrete basis for the next design phase. This study will also

  19. Development of core design and analyses technology for integral reactor

    International Nuclear Information System (INIS)

    Zee, Sung Quun; Lee, C. C.; Song, J. S. and others

    1999-03-01

    Integral reactors are developed for the applications such as sea water desalination, heat energy for various industries, and power sources for large container ships. In order to enhance the inherent and passive safety features, low power density concept is chosen for the integral reactor SMART. Moreover, ultra-longer cycle and boron-free operation concepts are reviewed for better plant economy and simple design of reactor system. Especially, boron-free operation concept brings about large difference in core configurations and reactivity controls from those of the existing large size commercial nuclear power plants and also causes many differences in the safety aspects. The ultimate objectives of this study include detailed core design of a integral reactor, development of the core design system and technology, and finally acquisition of the system design certificate. The goal of the first stage is the conceptual core design, that is, to establish the design bases and requirements suitable for the boron-free concept, to develop a core loading pattern, to analyze the nuclear, thermal and hydraulic characteristics of the core and to perform the core shielding design. Interface data for safety and performance analyses including fuel design data are produced for the relevant design analysis groups. Nuclear, thermal and hydraulic, shielding design and analysis code systems necessary for the core conceptual design are established through modification of the existing design tools and newly developed methodology and code modules. Core safety and performance can be improved by the technology development such as boron-free core optimization, advaned core monitoring and operational aid system. Feasiblity study on the improvement of the core protection and monitoring system will also contribute toward core safety and performance. Both the conceptual core design study and the related technology will provide concrete basis for the next design phase. This study will also

  20. Spacecraft System Integration and Test: SSTI Lewis critical design audit

    Science.gov (United States)

    Brooks, R. P.; Cha, K. K.

    1995-01-01

    The Critical Design Audit package is the final detailed design package which provides a comprehensive description of the SSTI mission. This package includes the program overview, the system requirements, the science and applications activities, the ground segment development, the assembly, integration and test description, the payload and technology demonstrations, and the spacecraft bus subsystems. Publication and presentation of this document marks the final requirements and design freeze for SSTI.

  1. Integral Monitored Retrievable Storage (MRS) Facility conceptual basis for design

    International Nuclear Information System (INIS)

    1985-10-01

    The purpose of the Conceptual Basis for Design is to provide a control document that establishes the basis for executing the conceptual design of the Integral Monitored Retrievable Storage (MRS) Facility. This conceptual design shall provide the basis for preparation of a proposal to Congress by the Department of Energy (DOE) for construction of one or more MRS Facilities for storage of spent nuclear fuel, high-level radioactive waste, and transuranic (TRU) waste. 4 figs., 25 tabs

  2. Digital integrated circuit design using Verilog and SystemVerilog

    CERN Document Server

    Mehler, Ronald W

    2014-01-01

    For those with a basic understanding of digital design, this book teaches the essential skills to design digital integrated circuits using Verilog and the relevant extensions of SystemVerilog. In addition to covering the syntax of Verilog and SystemVerilog, the author provides an appreciation of design challenges and solutions for producing working circuits. The book covers not only the syntax and limitations of HDL coding, but deals extensively with design problems such as partitioning and synchronization, helping you to produce designs that are not only logically correct, but will actually

  3. Parametric design and analysis framework with integrated dynamic models

    DEFF Research Database (Denmark)

    Negendahl, Kristoffer

    2014-01-01

    of building energy and indoor environment, are generally confined to late in the design process. Consequence based design is a framework intended for the early design stage. It involves interdisciplinary expertise that secures validity and quality assurance with a simulationist while sustaining autonomous...... control with the building designer. Consequence based design is defined by the specific use of integrated dynamic modeling, which includes the parametric capabilities of a scripting tool and building simulation features of a building performance simulation tool. The framework can lead to enhanced...

  4. Integrated Design Process in Problem-Based Learning

    DEFF Research Database (Denmark)

    Knudstrup, Mary-Ann

    2004-01-01

    This article reports and reflects on the learning achievements and the educational experiences in connection with the first years of the curriculum in Architecture at Aalborg University ?s Civil Engineer Education in Architecture & Design. In the article I will focus on the learning activity and ...... the students need in order to concentrate, mobilize creativity and find the personal design language which is a precondition for making good architecture....... and the method that are developed during the semester when working with an Integrated Design Process combining architecture, design, functional aspects, energy consumption, indoor environment, technology, and construction. I will emphasize the importance of working with different tools in the design process, e...

  5. Cryogenic propellant management: Integration of design, performance and operational requirements

    Science.gov (United States)

    Worlund, A. L.; Jamieson, J. R., Jr.; Cole, T. W.; Lak, T. I.

    1985-01-01

    The integration of the design features of the Shuttle elements into a cryogenic propellant management system is described. The implementation and verification of the design/operational changes resulting from design deficiencies and/or element incompatibilities encountered subsequent to the critical design reviews are emphasized. Major topics include: subsystem designs to provide liquid oxygen (LO2) tank pressure stabilization, LO2 facility vent for ice prevention, liquid hydrogen (LH2) feedline high point bleed, pogo suppression on the Space Shuttle Main Engine (SSME), LO2 low level cutoff, Orbiter/engine propellant dump, and LO2 main feedline helium injection for geyser prevention.

  6. Integrating Thermal Tools Into the Mechanical Design Process

    Science.gov (United States)

    Tsuyuki, Glenn T.; Siebes, Georg; Novak, Keith S.; Kinsella, Gary M.

    1999-01-01

    The intent of mechanical design is to deliver a hardware product that meets or exceeds customer expectations, while reducing cycle time and cost. To this end, an integrated mechanical design process enables the idea of parallel development (concurrent engineering). This represents a shift from the traditional mechanical design process. With such a concurrent process, there are significant issues that have to be identified and addressed before re-engineering the mechanical design process to facilitate concurrent engineering. These issues also assist in the integration and re-engineering of the thermal design sub-process since it resides within the entire mechanical design process. With these issues in mind, a thermal design sub-process can be re-defined in a manner that has a higher probability of acceptance, thus enabling an integrated mechanical design process. However, the actual implementation is not always problem-free. Experience in applying the thermal design sub-process to actual situations provides the evidence for improvement, but more importantly, for judging the viability and feasibility of the sub-process.

  7. Development of mechanical design technology for integral reactor

    International Nuclear Information System (INIS)

    Park, Keun Bae; Choi, Suhn; Kim, Kang Soo; Kim, Tae Wan; Jeong, Kyeong Hoon; Lee, Gyu Mahn

    1999-03-01

    While Korean nuclear reactor strategy seems to remain focused on the large capacity power generation, it is expected that demand of small and medium size reactor will arise for multi-purpose application such as small capacity power generation, co-generation and sea water desalination. With this in mind, an integral reactor SMART is under development. Design concepts, system layout and types of equipment of integral reactor are significantly different from those of loop type reactor. Conceptual design development of mechanical structures of integral reactor SMART is completed through the first stage of the project. Efforts were endeavored for the establishment of design basis and evaluation of applicable codes and standards. Design and functional requirements of major structural components were set up, and three dimensional structural modelling of SMART reactor vessel assembly was prepared. Also, maintenance and repair scheme as well as preliminary fabricability evaluation were carried out. Since small integral reactor technology includes sensitive technologies and know-how's, it is hard to achieve systematic and comprehensive technology transfer from nuclear-advanced countries. Thus, it is necessary to develop the related design technology and to verify the adopted methodologies through test and experiments in order to assure the structural integrity of reactor system. (author)

  8. Development of mechanical design technology for integral reactor

    Energy Technology Data Exchange (ETDEWEB)

    Park, Keun Bae; Choi, Suhn; Kim, Kang Soo; Kim, Tae Wan; Jeong, Kyeong Hoon; Lee, Gyu Mahn

    1999-03-01

    While Korean nuclear reactor strategy seems to remain focused on the large capacity power generation, it is expected that demand of small and medium size reactor will arise for multi-purpose application such as small capacity power generation, co-generation and sea water desalination. With this in mind, an integral reactor SMART is under development. Design concepts, system layout and types of equipment of integral reactor are significantly different from those of loop type reactor. Conceptual design development of mechanical structures of integral reactor SMART is completed through the first stage of the project. Efforts were endeavored for the establishment of design basis and evaluation of applicable codes and standards. Design and functional requirements of major structural components were setup, and three dimensional structural modelling of SMART reactor vessel assembly was prepared. Also, maintenance and repair scheme as well as preliminary fabricability evaluation were carried out. Since small integral reactor technology includes sensitive technologies and know-how's, it is hard to achieve systematic and comprehensive technology transfer from nuclear-advanced countries. Thus, it is necessary to develop the related design technology and to verify the adopted methodologies through test and experiments in order to assure the structural integrity of reactor system. (author)

  9. Integrating Safeguards and Security with Safety into Design

    International Nuclear Information System (INIS)

    Bean, Robert S.; Hockert, John W.; Hebditch, David J.

    2009-01-01

    There is a need to minimize security risks, proliferation hazards, and safety risks in the design of new nuclear facilities in a global environment of nuclear power expansion, while improving the synergy of major design features and raising operational efficiency. In 2008, the U.S. Department of Energy (DOE), National Nuclear Security Administration (NNSA) launched the Next Generation Safeguards Initiative (NGSI) covering many safeguards areas. One of these, launched by NNSA with support of the DOE Office of Nuclear Energy, was a multi-laboratory project, led by the Idaho National Laboratory (INL), to develop safeguards by design. The proposed Safeguards-by-Design (SBD) process has been developed as a structured approach to ensure the timely, efficient, and cost effective integration of international safeguards and other nonproliferation barriers with national material control and accountability, physical security, and safety objectives into the overall design process for the nuclear facility lifecycle. A graded, iterative process was developed to integrate these areas throughout the project phases. It identified activities, deliverables, interfaces, and hold points covering both domestic regulatory requirements and international safeguards using the DOE regulatory environment as exemplar to provide a framework and guidance for project management and integration of safety with security during design. Further work, reported in this paper, created a generalized SBD process which could also be employed within the licensed nuclear industry and internationally for design of new facilities. Several tools for integrating safeguards, safety, and security into design are discussed here. SBD appears complementary to the EFCOG TROSSI process for security and safety integration created in 2006, which focuses on standardized upgrades to enable existing DOE facilities to meet a more severe design basis threat. A collaborative approach is suggested.

  10. Design of an integrated I and C system

    International Nuclear Information System (INIS)

    Lee, C. K.; Oh, I. S.; Kim, D. H.

    2004-08-01

    The final goal of this project is to develop an integrated I and C systems, and through this project the localized equipment and systems being developed should secure the safety, the reliability, their applicability and technical competitiveness. As well, the technical interfaces among sub-projects should be maintained for integration. The results of this project are as following ; 1. Development of an integrated I and C system architecture: Development of the design concepts for KNICS and the design requirements for each I and C system, Development of the design requirements of control systems based on DCS, Design of the communication systems, Design of the interface signals among systems and analysis of traffic load for networks, Conceptual design of measuring and monitoring systems, Review of the structure of computer systems for information processing, Development of architectures for each system and KOICS 2. Technological integration and management of projects: Development of evaluation criteria for DCS and network systems, Evaluation of the DCS prototype, Design review of KNICS protection system, Review of the functions and design requirements of I and C systems in NPP, Analysis of the I and C system H/W in NPP and the APR1400 I and C system design, Review of the technology criteria and the regulatory trend for licensing issues, Extracting items for preparing the technical description of I and C systems, a part of proposal to invitation to bid (ITB), Planning for KNICS to be of practical use The results of this project will be applied as design bases during the development of 2nd phase KNICS. As well it is expected that the results of this project will be finally applied for the technical self-reliance of component design and manufacturing of NPP I and C systems

  11. CopperCore Service Integration, Integrating IMS Learning Design and IMS Question and Test Interoperability

    NARCIS (Netherlands)

    Vogten, Hubert; Martens, Harrie; Nadolski, Rob; Tattersall, Colin; Van Rosmalen, Peter; Koper, Rob

    2006-01-01

    Vogten, H., Martens, H., Nadolski, R., Tattersall, C., Rosmalen, van, P., Koper, R., (2006). CopperCore Service Integration, Integrating IMS Learning Design and IMS Question and Test Interoperability. Proceedings of the 6th IEEE International Conference on Advanced Learning Technologies (pp.

  12. Integrating IMS Learning Design and IMS Question and Test Interoperability using CopperCore Service Integration

    NARCIS (Netherlands)

    Vogten, Hubert; Martens, Harrie; Nadolski, Rob; Tattersall, Colin; Van Rosmalen, Peter; Koper, Rob

    2006-01-01

    Please, cite this publication as: Vogten, H., Martens, H., Nadolski, R., Tattersall, C., van Rosmalen, P., & Koper, R. (2006). Integrating IMS Learning Design and IMS Question and Test Interoperability using CopperCore Service Integration. Proceedings of International Workshop in Learning Networks

  13. Suspended Integrated Strip-line Transition Design for Highly Integrated Radar Systems

    Science.gov (United States)

    2017-03-01

    technology. The measured results show good correlation to the simulated results with a return loss and insertion loss of less than 10 dB and greater...SSS); Suspended Integrated Strip-line (SISL) RF packaging; Ultra-wideband (UWB). Introduction The next generation of highly integrated radar...RF Circuit Design,” Second Edition, Pearson Education, 2009. 3. B. Ma, A. Chousseaud, and S. Toutain, “A new design of compact planar microstrip

  14. Opus: A Coordination Language for Multidisciplinary Applications

    Directory of Open Access Journals (Sweden)

    Barbara Chapman

    1997-01-01

    Full Text Available Data parallel languages, such as High Performance Fortran, can be successfully applied to a wide range of numerical applications.However, many advanced scientific and engineering applications are multidisciplinary and heterogeneous in nature, and thus do not fit well into the data parallel paradigm. In this paper we present Opus, a language designed to fill this gap. The central concept of Opus is a mechanism called ShareD Abstractions (SDA. An SDA can be used as a computation server, i.e., a locus of computational activity, or as a data repository for sharing data between asynchronous tasks. SDAs can be internally data parallel, providing support for the integration of data and task parallelism as well as nested task parallelism. They can thus be used to express multidisciplinary applications in a natural and efficient way. In this paper we describe the features of the language through a series of examples and give an overview of the runtime support required to implement these concepts in parallel and distributed environments.

  15. Requirements of Integrated Design Teams While Evaluating Advanced Energy Retrofit Design Options in Immersive Virtual Environments

    Directory of Open Access Journals (Sweden)

    Xue Yang

    2015-12-01

    Full Text Available One of the significant ways to save energy use in buildings is to implement advanced energy retrofits in existing buildings. Improving energy performance of buildings through advanced energy retrofitting requires a clear understanding of the cost and energy implications of design alternatives from various engineering disciplines when different retrofit options are considered. The communication of retrofit design alternatives and their energy implications is essential in the decision-making process, as it affects the final retrofit selections and hence the energy efficiency of the retrofitted buildings. The objective of the research presented here was to identify a generic list of information requirements that are needed to be shared and collectively analyzed by integrated design teams during advanced energy retrofit design review meetings held in immersive settings. While identifying such requirements, the authors used an immersive environment based iterative requirements elicitation approach. The technology was used as a means to better identify the information requirements of integrated design teams to be analyzed as a group. This paper provides findings on information requirements of integrated design teams when evaluating retrofit options in immersive virtual environments. The information requirements were identified through interactions with sixteen experts in design and energy modeling domain, and validated with another group of participants consisting of six design experts who were experienced in integrated design processes. Industry practitioners can use the findings in deciding on what information to share with integrated design team members during design review meetings that utilize immersive virtual environments.

  16. A design approach for integrating thermoelectric devices using topology optimization

    DEFF Research Database (Denmark)

    Soprani, Stefano; Haertel, Jan Hendrik Klaas; Lazarov, Boyan Stefanov

    2016-01-01

    Efficient operation of thermoelectric devices strongly relies on the thermal integration into the energy conversion system in which they operate. Effective thermal integration reduces the temperature differences between the thermoelectric module and its thermal reservoirs, allowing the system...... to operate more efficiently. This work proposes and experimentally demonstrates a topology optimization approach as a design tool for efficient integration of thermoelectric modules into systems with specific design constraints. The approach allows thermal layout optimization of thermoelectric systems...... for different operating conditions and objective functions, such as temperature span, efficiency, and power recoveryrate. As a specific application, the integration of a thermoelectric cooler into the electronics section ofa downhole oil well intervention tool is investigated, with the objective of minimizing...

  17. Multidisciplinary team care in rehabilitation

    DEFF Research Database (Denmark)

    Momsen, A.-M.; Nielsen, C.V.; Rasmussen, J.O.

    2012-01-01

    Objectives: To systematically investigate current scientific evidence about the effectiveness of multidisciplinary team rehabilitation for different health problems. Data sources: A comprehensive literature search was conducted in Cochrane, Medline, DARE, Embase, and Cinahl databases, and research...... for adults, without restrictions in terms of study population or outcomes. The most recent reviews examining a study population were selected. Data extraction: Two reviewers independently extracted information about study populations, sample sizes, study designs, rehabilitation settings, the team...

  18. Mathematical modeling with multidisciplinary applications

    CERN Document Server

    Yang, Xin-She

    2013-01-01

    Features mathematical modeling techniques and real-world processes with applications in diverse fields Mathematical Modeling with Multidisciplinary Applications details the interdisciplinary nature of mathematical modeling and numerical algorithms. The book combines a variety of applications from diverse fields to illustrate how the methods can be used to model physical processes, design new products, find solutions to challenging problems, and increase competitiveness in international markets. Written by leading scholars and international experts in the field, the

  19. DESIGN OF INFORMATION MANAGEMENT SYSTEM OF VERTICALLY INTEGRATED AGRICULTURAL HOLDINGS

    Directory of Open Access Journals (Sweden)

    Александр Витальевич ШМАТКО

    2015-05-01

    Full Text Available The paper deals with an approach to the design and development of information systems for the management and optimization of the organizational structure of vertically integrated agricultural holdings. A review of the problems of building and improving the organizational structure of vertically integrated agricultural holding is made. A method of constructing a discrete model management structure agricultural holding, which minimizes the costs associated with attracting applicants to work, is proposed.

  20. Grid integration impacts on wind turbine design and development

    DEFF Research Database (Denmark)

    Hansen, Anca Daniela; Cutululis, Nicolaos Antonio; Sørensen, Poul Ejnar

    2009-01-01

    This paper presents an overall perspective on contemporary issues like wind power plants and grid integration. The purpose is to present and discuss the impacts of emerging new grid connection requirements on modern wind turbines. The grid integration issue has caused several new challenges......, the grid integration aspect has also an effect on wind turbines' role in the power system, on wind turbine technologies' survival on the market, as well as on the wind turbines' loads. Over the last years, it became obviously, that there it is an increasing need for design and research of wind turbines...... to the wind turbine design and development. The survival of different wind turbine concepts and controls is strongly conditioned by their ability to comply with stringent grid connection requirements, imposed by utility companies. Beside its impact on the mechanical design and control of wind turbines...

  1. Availability objectives integration to design. The CIDEM approach

    International Nuclear Information System (INIS)

    Degrave, C.; Martin-Onraet, M.

    1994-01-01

    Considering the operation experience feedback from its nuclear park and from foreign parks, and considering new approaches and design tools such as concurrent engineering, total quality, etc., EDF (Electricite de France) has decided to start the CIDEM approach (integration of availability, operating experience feedback and maintenance into design), an analytical and systematical study process for new projects (REP2000 (or PWR2000)), in order to optimize as much as possible the design phase while integrating maintenance, availability and safety objectives, with the view of a minimized kWh cost. This process, already used in other industries, employs concepts such as RAM (Reliability Availability Maintainability), RCM (Reliability Centered Maintenance) and ILS (Integrated Logistic Support). The availability and maintenance scheduling studies for the REP2000 project are detailed. 10 fig., 6 tab

  2. Design and evaluation of an integrated safeguards system: principles

    International Nuclear Information System (INIS)

    Markin, J.T.; Coulter, C.A.; Gutmacher, R.G.; Whitty, W.J.

    1984-07-01

    An integrated safeguards system is defined as a collection of safeguards activities in which system components are coordinated to meet safeguards objectives efficiently within constraints imposed by safeguards resources, facility operations, potential adversaries, and regulatory requirements. This paper describes principles for designing and evaluating an integrated safeguards system that consists of four parts: (1) a problem definition phase that specifies resources and constraints composing the problem boundary values; (2) a system analysis/synthesis phase that describes how to select and integrate safeguards activities for efficient attainment of system objectives; (3) a system evaluation/optimization phase that defines measures of safeguards performance and develops methods for evaluating them; and (4) a decision-making phase that develops principles for selecting admissible designs and preference-ordering designs. 6 references, 4 figures, 5 tables

  3. Design and evaluation of an integrated safeguards system: principles

    International Nuclear Information System (INIS)

    Markin, J.T.; Coulter, C.A.; Gutmacher, R.G.; Whitty, W.J.

    1984-01-01

    An integrated safeguards system is defined as a collection of safeguards activities in which system components are coordinated to meet safeguards objectives efficiently within constraints imposed by safeguards resources, facility operations, potential adversaries, and regulatory requirements. This paper describes principles for designing and evaluating an integrated safeguards system that consists of four parts: a problem definition phase that specifies resources and constraints composing the problem boundary values, a system analysis/synthesis phase that describes how to select and integrate safeguards activities for efficient attainment of system objectives, a system evaluation/optimization phase that defines measures of safeguards performance and develops methods for evaluating them, and a decision-making phase that develops principles for selecting admissible designs and preference-ordering designs

  4. The computational design of Geological Disposal Technology Integration System

    International Nuclear Information System (INIS)

    Ishihara, Yoshinao; Iwamoto, Hiroshi; Kobayashi, Shigeki; Neyama, Atsushi; Endo, Shuji; Shindo, Tomonori

    2002-03-01

    In order to develop 'Geological Disposal Technology Integration System' that is intended to systematize as knowledge base for fundamental study, the computational design of an indispensable database and image processing function to 'Geological Disposal Technology Integration System' was done, the prototype was made for trial purposes, and the function was confirmed. (1) Database of Integration System which systematized necessary information and relating information as an examination of a whole of repository composition and managed were constructed, and the system function was constructed as a system composed of image processing, analytical information management, the repository component management, and the system security function. (2) The range of the data treated with this system and information was examined, the design examination of the database structure was done, and the design examination of the image processing function of the data preserved in an integrated database was done. (3) The prototype of the database concerning a basic function, the system operation interface, and the image processing function was manufactured to verify the feasibility of the 'Geological Disposal Technology Integration System' based on the result of the design examination and the function was confirmed. (author)

  5. Design and control of integrated chromatography column sequences.

    Science.gov (United States)

    Andersson, Niklas; Löfgren, Anton; Olofsson, Marianne; Sellberg, Anton; Nilsson, Bernt; Tiainen, Peter

    2017-07-01

    To increase the productivity in biopharmaceutical production, a natural step is to introduce integrated continuous biomanufacturing which leads to fewer buffer and storage tanks, smaller sizes of integrated unit operations, and full automation of the operation. The main contribution of this work is to illustrate a methodology for design and control of a downstream process based on integrated column sequences. For small scale production, for example, pre-clinical studies, integrated column sequences can be implemented on a single chromatography system. This makes for a very efficient drug development platform. The proposed methodology is composed of four steps and is governed by a set of tools, that is presented, that makes the transition from batch separations to a complete integrated separation sequence as easy as possible. This methodology, its associated tools and the physical implementation is presented and illustrated on a case study where the target protein is separated from impurities through an integrated four column sequence. This article shows that the design and control of an integrated column sequence was successfully implemented for a tertiary protein separation problem. © 2017 American Institute of Chemical Engineers Biotechnol. Prog., 33:923-930, 2017. © 2017 American Institute of Chemical Engineers.

  6. Integral Monitored Retrievable Storage (MRS) Facility conceptual design report

    International Nuclear Information System (INIS)

    1985-09-01

    This report presents a summary design description of the Conceptual Design for an Integral Monitored Retrievable Storage (MRS) Facility, as prepared by The Ralph M. Parsons Company under an A-E services contract with the Richland Operations Office of the Department of Energy. More detailed design requirements and design data are set forth in the Basis for Design and Design Report, bound under separate cover and available for reference by those desiring such information. The design data provided in this Design Report Executive Summary, the Basis for Design, and the Design Report include contributions by the Waste Technology Services Division of Westinghouse Electric Corporation (WEC), which was responsible for the development of the waste receiving, packaging, and storage systems, and Golder Associates Incorporated (GAI), which supported the design development with program studies. The MRS Facility design requirements, which formed the basis for the design effort, were prepared by Pacific Northwest Laboratory for the US Department of Energy, Richland Operations Office, in the form of a Functional Design Criteria (FDC) document, Rev. 4, August 1985. 9 figs., 6 tabs

  7. Challenges and opportunities in integration of design and control

    DEFF Research Database (Denmark)

    Huusom, Jakob Kjøbsted

    2015-01-01

    Process synthesis and design of plant operation are related topics but current industrial practice solves these problems sequentially. The implication of this sequential strategy may result in design of processing systems which are very hard to control. This paper presents a discussion on drivers...... for an integrated approach and outlines the challenges in formulation of such a multi-objective synthesis problem. This discussion is viewed in relation to some of the changing trends in the industry. Significant results have been published which in different ways seek to handle the integrated problem. Further...

  8. A Novel Analog Integrated Circuit Design Course Covering Design, Layout, and Resulting Chip Measurement

    Science.gov (United States)

    Lin, Wei-Liang; Cheng, Wang-Chuan; Wu, Chen-Hao; Wu, Hai-Ming; Wu, Chang-Yu; Ho, Kuan-Hsuan; Chan, Chueh-An

    2010-01-01

    This work describes a novel, first-year graduate-level analog integrated circuit (IC) design course. The course teaches students analog circuit design; an external manufacturer then produces their designs in three different silicon chips. The students, working in pairs, then test these chips to verify their success. All work is completed within…

  9. Design criteria of integrated reactors based on transients

    International Nuclear Information System (INIS)

    Zanocco, P.; Gimenez, M.; Delmastro, D.

    1999-01-01

    A new tendency in integrated reactors conceptual design is to include safety criteria through accident analysis. In this work, the effect of design parameters in a Loss of Heat Sink transient using design maps is analyzed. Particularly, geometry related parameters and reactivity coefficients are studied. Also the effect of primary relief/safety valve during the transient is evaluated. A design map for valve area vs. coolant density reactivity coefficient is obtained. A computer code (HUARPE) is developed in order to simulate these transients. Coolant, steam dome, pressure vessel structures and core models are implemented. This code is checked against TRAC with satisfactory results. (author)

  10. Toshiba integrated information system for design of nuclear power plants

    International Nuclear Information System (INIS)

    Abe, Yoko; Kawamura, Hirobumi; Sasaki, Norio; Takasaka, Kiyoshi

    1993-01-01

    TOSHIBA aims to secure safety, increase reliability and improve efficiency through the engineering for nuclear power plants and has been introducing Computer Aided Engineering (CAE). Up to the present, TOSHIBA has been developing computer systems which support each field of design and applying them to the design of nuclear power plants. The new design support system has been developed to integrate each of those systems in order to realize much greater improvement in accuracy and increase of reliability in design using state-of-the-art computer technology

  11. Integrating design and purchasing [in nuclear engineering] with Ingecad

    International Nuclear Information System (INIS)

    Anon.

    1989-01-01

    Ingecad was developed by the Ingevision division of Framatome to overcome deficiencies in traditional computer-aided design. It was developed for nuclear power project engineering around the principle of the shared management of a common database, thus making it possible to integrate several engineering disciplines. The multiuser database is managed and accessed by the different application softwares, corresponding to particular aspects of the engineering task: electrical and process control schematics; plant piping design; pressurized equipment design etc. The use of a common database ensures coherence between the different engineering disciplines, particularly between the process engineering, the plant layout design, the piping, and the instrumentation and control engineering. (author)

  12. Integrated airfoil and blade design method for large wind turbines

    DEFF Research Database (Denmark)

    Zhu, Wei Jun; Shen, Wen Zhong; Sørensen, Jens Nørkær

    2014-01-01

    This paper presents an integrated method for designing airfoil families of large wind turbine blades. For a given rotor diameter and a tip speed ratio, optimal airfoils are designed based on the local speed ratios. To achieve a high power performance at low cost, the airfoils are designed...... with the objectives of high Cp and small chord length. When the airfoils are obtained, the optimum flow angle and rotor solidity are calculated which forms the basic input to the blade design. The new airfoils are designed based on a previous in-house designed airfoil family which was optimized at a Reynolds number...... of 3 million. A novel shape perturbation function is introduced to optimize the geometry based on the existing airfoils which simplifies the design procedure. The viscous/inviscid interactive code XFOIL is used as the aerodynamic tool for airfoil optimization at a Reynolds number of 16 million...

  13. The challenge of integrating evidence-based design.

    Science.gov (United States)

    Martin, Caren S

    2009-01-01

    This paper discusses the integration of evidence-based design (EBD) into the design process as an innovation, illuminates the significance and progress of the diffusion of this innovation, and identifies EBD advocates and the consequences of meeting the EBD challenge. A free tool for engaging in EBD is explored. Healthcare designers are leading the EBD charge, because their clients depend on it. But not all designers engage in EBD, because it may be beyond the resources of a firm or outside its culture. However, as with other meaningful design innovations, designers who do not practice EBD could fall by the wayside. EBD is a product of the diffusion of the innovation of evidence-based medicine. The academy (i.e., the collective of institutions of higher education), design organizations, design communities, and the media all contribute to the diffusion of EBD. However, the quantity, quality, and understandability of evidence continue to challenge its broad adoption. InformeDesign®, a free, Internet-based tool, presents information to designers in a concise, understandable way. Firms must invest in EBD incrementally as a value-added component of design to meet current and future challenges. It is important for designers to realize that engaging in EBD is not a rejection of creativity, but a means by which to elevate their design solutions. ©2009 VENDOME GROUP, LLC

  14. Multidisciplinary Optimization Branch Experience Using iSIGHT Software

    Science.gov (United States)

    Padula, S. L.; Korte, J. J.; Dunn, H. J.; Salas, A. O.

    1999-01-01

    The Multidisciplinary Optimization (MDO) Branch at NASA Langley is investigating frameworks for supporting multidisciplinary analysis and optimization research. A framework provides software and system services to integrate computational tasks and allows the researcher to concentrate more on the application and less on the programming details. A framework also provides a common working environment and a full range of optimization tools, and so increases the productivity of multidisciplinary research teams. Finally, a framework enables staff members to develop applications for use by disciplinary experts in other organizations. This year, the MDO Branch has gained experience with the iSIGHT framework. This paper describes experiences with four aerospace applications, including: (1) reusable launch vehicle sizing, (2) aerospike nozzle design, (3) low-noise rotorcraft trajectories, and (4) acoustic liner design. Brief overviews of each problem are provided, including the number and type of disciplinary codes and computation time estimates. In addition, the optimization methods, objective functions, design variables, and constraints are described for each problem. For each case, discussions on the advantages and disadvantages of using the iSIGHT framework are provided as well as notes on the ease of use of various advanced features and suggestions for areas of improvement.

  15. Barriers and Challenges in the Integrated Design Process Approcach

    DEFF Research Database (Denmark)

    Knudstrup, Mary-Ann

    2006-01-01

    ABSTRACT: In the future, it will be a huge challenge to make sustainable building design by using a more holistic and innovative approach in order to be able to decrease or reduce the use of energy for heating and cooling in new building projects. This is seen in the perspective of the Kyoto agre....... It also describes the barriers and the challenges that must be overcome when trying to cross the borders between the two fields of engineering and architecture to design sustainable architecture....... agreement for reducing the global heating. This paper will briefly present the method of the Integrated Design Process, IDP [1]. It describes the background and means for developing a new method for designing integrated architecture in an interdisciplinary approach between architecture and engineering...

  16. Analog integrated circuits design for processing physiological signals.

    Science.gov (United States)

    Li, Yan; Poon, Carmen C Y; Zhang, Yuan-Ting

    2010-01-01

    Analog integrated circuits (ICs) designed for processing physiological signals are important building blocks of wearable and implantable medical devices used for health monitoring or restoring lost body functions. Due to the nature of physiological signals and the corresponding application scenarios, the ICs designed for these applications should have low power consumption, low cutoff frequency, and low input-referred noise. In this paper, techniques for designing the analog front-end circuits with these three characteristics will be reviewed, including subthreshold circuits, bulk-driven MOSFETs, floating gate MOSFETs, and log-domain circuits to reduce power consumption; methods for designing fully integrated low cutoff frequency circuits; as well as chopper stabilization (CHS) and other techniques that can be used to achieve a high signal-to-noise performance. Novel applications using these techniques will also be discussed.

  17. Design and development of small and medium integral reactor core

    International Nuclear Information System (INIS)

    Zee, Sung Quun; Chang, M. H.; Lee, C. C.; Song, J. S.; Cho, B. O.; Kim, K. Y.; Kim, S. J.; Park, S. Y.; Lee, K. B.; Lee, C. H.; Chun, T. H.; Oh, D. S.; In, W. K.; Kim, H. K.; Lee, C. B.; Kang, H. S.; Song, K. N.

    1997-07-01

    Recently, the role of small and medium size integral reactors is remarkable in the heat applications rather than the electrical generations. Such a range of possible applications requires extensive used of inherent safety features and passive safety systems. It also requires ultra-longer cycle operations for better plant economy. Innovative and evolutionary designs such as boron-free operations and related reactor control methods that are necessary for simple reactor system design are demanded for the small and medium reactor (SMR) design, which are harder for engineers to implement in the current large size nuclear power plants. The goals of this study are to establish preliminary design criteria, to perform the preliminary conceptual design and to develop core specific technology for the core design and analysis for System-integrated Modular Advanced ReacTor (SMART) of 330 MWt power. Based on the design criteria of the commercial PWR's, preliminary design criteria will be set up. Preliminary core design concept is going to be developed for the ultra-longer cycle and boron-free operation and core analysis code system is constructed for SMART. (author). 100 refs., 40 tabs., 92 figs

  18. NASA Subsonic Rotary Wing Project-Multidisciplinary Analysis and Technology Development: Overview

    Science.gov (United States)

    Yamauchi, Gloria K.

    2009-01-01

    This slide presentation reviews the objectives of the Multidisciplinary Analysis and Technology Development (MDATD) in the Subsonic Rotary Wing project. The objectives are to integrate technologies and analyses to enable advanced rotorcraft and provide a roadmap to guide Level 1 and 2 research. The MDATD objectives will be met by conducting assessments of advanced technology benefits, developing new or enhanced design tools, and integrating Level 2 discipline technologies to develop and enable system-level analyses and demonstrations.

  19. Integral Engine Inlet Particle Separator. Volume 2. Design Guide

    Science.gov (United States)

    1975-08-01

    herein will be used in the design of integral inlet particle separators for future Army aircraft gas turbine engines. Apprupriate technical personnel...into the comprensor at some future date. 5. A typical scavenge vane design Js; shown in Figures 85 and 86. The important features of the scavenge...service passageweys, for cooling of oil, and for directing sand and air into the scroll. Orientetion of the vanes is set by collection efficiency

  20. Development of core design and analyses technology for integral reactor

    International Nuclear Information System (INIS)

    Zee, Sung Quun; Lee, C. C.; Kim, K. Y.

    2002-03-01

    In general, small and medium-sized integral reactors adopt new technology such as passive and inherent safety concepts to minimize the necessity of power source and operator actions, and to provide the automatic measures to cope with any accidents. Specifically, such reactors are often designed with a lower core power density and with soluble boron free concept for system simplification. Those reactors require ultra long cycle operation for higher economical efficiency. This cycle length requirement is one of the important factors in the design of burnable absorbers as well as assurance of shutdown margin. Hence, both computer code system and design methodology based on the today's design technology for the current commercial reactor cores require intensive improvement for the small and medium-sized soluble boron free reactors. New database is also required for the development of this type of reactor core. Under these technical requirements, conceptual design of small integral reactor SMART has been performed since July 1997, and recently completed under the long term nuclear R and D program. Thus, the final objectives of this work is design and development of an integral reactor core and development of necessary indigenous design technology. To reach the goal of the 2nd stage R and D program for basic design of SMART, design bases and requirements adequate for ultra long cycle and soluble boron free concept are established. These bases and requirements are satisfied by the core loading pattern. Based on the core loading pattern, nuclear, and thermal and hydraulic characteristics are analyzed. Also included are fuel performance analysis and development of a core protection and monitoring system that is adequate for the soluble boron free core of an integral reactor. Core shielding design analysis is accomplished, too. Moreover, full scope interface data are produced for reactor safety and performance analyses and other design activities. Nuclear, thermal and

  1. Integrating rock mechanics issues with repository design through design process principles and methodology

    International Nuclear Information System (INIS)

    Bieniawski, Z.T.

    1996-01-01

    A good designer needs not only knowledge for designing (technical know-how that is used to generate alternative design solutions) but also must have knowledge about designing (appropriate principles and systematic methodology to follow). Concepts such as open-quotes design for manufactureclose quotes or open-quotes concurrent engineeringclose quotes are widely used in the industry. In the field of rock engineering, only limited attention has been paid to the design process because design of structures in rock masses presents unique challenges to the designers as a result of the uncertainties inherent in characterization of geologic media. However, a stage has now been reached where we are be able to sufficiently characterize rock masses for engineering purposes and identify the rock mechanics issues involved but are still lacking engineering design principles and methodology to maximize our design performance. This paper discusses the principles and methodology of the engineering design process directed to integrating site characterization activities with design, construction and performance of an underground repository. Using the latest information from the Yucca Mountain Project on geology, rock mechanics and starter tunnel design, the current lack of integration is pointed out and it is shown how rock mechanics issues can be effectively interwoven with repository design through a systematic design process methodology leading to improved repository performance. In essence, the design process is seen as the use of design principles within an integrating design methodology, leading to innovative problem solving. In particular, a new concept of open-quotes Design for Constructibility and Performanceclose quotes is introduced. This is discussed with respect to ten rock mechanics issues identified for repository design and performance

  2. Achieving integration in mixed methods designs-principles and practices.

    Science.gov (United States)

    Fetters, Michael D; Curry, Leslie A; Creswell, John W

    2013-12-01

    Mixed methods research offers powerful tools for investigating complex processes and systems in health and health care. This article describes integration principles and practices at three levels in mixed methods research and provides illustrative examples. Integration at the study design level occurs through three basic mixed method designs-exploratory sequential, explanatory sequential, and convergent-and through four advanced frameworks-multistage, intervention, case study, and participatory. Integration at the methods level occurs through four approaches. In connecting, one database links to the other through sampling. With building, one database informs the data collection approach of the other. When merging, the two databases are brought together for analysis. With embedding, data collection and analysis link at multiple points. Integration at the interpretation and reporting level occurs through narrative, data transformation, and joint display. The fit of integration describes the extent the qualitative and quantitative findings cohere. Understanding these principles and practices of integration can help health services researchers leverage the strengths of mixed methods. © Health Research and Educational Trust.

  3. Integrated design and manufacturing for the high speed civil transport

    Science.gov (United States)

    1993-01-01

    In June 1992, Georgia Tech's School of Aerospace Engineering was awarded a NASA University Space Research Association (USRA) Advanced Design Program (ADP) to address 'Integrated Design and Manufacturing for the High Speed Civil Transport (HSCT)' in its graduate aerospace systems design courses. This report summarizes the results of the five courses incorporated into the Georgia Tech's USRA ADP program. It covers AE8113: Introduction to Concurrent Engineering, AE4360: Introduction to CAE/CAD, AE4353: Design for Life Cycle Cost, AE6351: Aerospace Systems Design One, and AE6352: Aerospace Systems Design Two. AE8113: Introduction to Concurrent Engineering was an introductory course addressing the basic principles of concurrent engineering (CE) or integrated product development (IPD). The design of a total system was not the objective of this course. The goal was to understand and define the 'up-front' customer requirements, their decomposition, and determine the value objectives for a complex product, such as the high speed civil transport (HSCT). A generic CE methodology developed at Georgia Tech was used for this purpose. AE4353: Design for Life Cycle Cost addressed the basic economic issues for an HSCT using a robust design technique, Taguchi's parameter design optimization method (PDOM). An HSCT economic sensitivity assessment was conducted using a Taguchi PDOM approach to address the robustness of the basic HSCT design. AE4360: Introduction to CAE/CAD permitted students to develop and utilize CAE/CAD/CAM knowledge and skills using CATIA and CADAM as the basic geometric tools. AE6351: Aerospace Systems Design One focused on the conceptual design refinement of a baseline HSCT configuration as defined by Boeing, Douglas, and NASA in their system studies. It required the use of NASA's synthesis codes FLOPS and ACSYNT. A criterion called the productivity index (P.I.) was used to evaluate disciplinary sensitivities and provide refinements of the baseline HSCT

  4. The GOTTHARD charge integrating readout detector: design and characterization

    International Nuclear Information System (INIS)

    Mozzanica, A; Bergamaschi, A; Dinapoli, R; Greiffenberg, D; Henrich, B; Johnson, I; Valeria, R; Schmitt, B; Xintian, S; Graafsma, H; Lohmann, M

    2012-01-01

    A charge integrating readout ASIC (Application Specific Integrated Circuit) for silicon strip sensors has been developed at PSI in collaboration with DESY. The goal of the project is to provide a charge integrating readout system able to cope with the pulsed beam of XFEL machines and at the same time to retain the high dynamic range and single photon resolution performances typical for photon counting systems. The ASIC, designed in IBM 130 nm CMOS technology, takes advantage of its three gain stages with automatic stage selection to achieve a dynamic range of 10000 12 keV photons and a noise better than 300 e.n.c.. The 4 analog outputs of the ASIC are optimized for speed, allowing frame rates higher than 1 MHz, without compromises on linearity and noise performances. This work presents the design features of the ASIC, and reports the characterization results of the chip itself.

  5. Integrated seismic design of structure and control systems

    CERN Document Server

    Castaldo, Paolo

    2014-01-01

    The structural optimization procedure presented in this book makes it possible to achieve seismic protection through integrated structural/control system design. In particular, it is explained how slender structural systems with a high seismic performance can be achieved through inclusion of viscous and viscoelastic dampers as an integral part of the system. Readers are provided with essential introductory information on passive structural control and passive energy dissipation systems. Dynamic analyses of both single and multiple degree of freedom systems are performed in order to verify the achievement of pre-assigned performance targets, and it is explained how the optimal integrated design methodology, also relevant to retrofitting of existing buildings, should be applied. The book illustrates how structural control research is opening up new possibilities in structural forms and configurations without compromising structural performance.

  6. On CAD-integrated Structural Topology and Design Optimization

    DEFF Research Database (Denmark)

    Olhoff, Niels; Bendsøe, M.P.; Rasmussen, John

    1991-01-01

    Concepts underlying an interactive CAD-based engineering design optimization system are developed, and methods of optimizing the topology, shape and sizing of mechanical components are presented. These methods are integrated in the system, and the method for determining the optimal topology is used...

  7. Designing the Distributed Model Integration Framework – DMIF

    NARCIS (Netherlands)

    Belete, Getachew F.; Voinov, Alexey; Morales, Javier

    2017-01-01

    We describe and discuss the design and prototype of the Distributed Model Integration Framework (DMIF) that links models deployed on different hardware and software platforms. We used distributed computing and service-oriented development approaches to address the different aspects of

  8. Overview of design issues in product-integrated Photovoltaics

    NARCIS (Netherlands)

    Apostolou, G.; Reinders, Angelina H.M.E.

    2014-01-01

    This paper presents an overview of the design features and characteristics of photovoltaic (PV)-powered products based on a literature study on product-integrated PV and an analysis of 90 PV-powered products executed during 2011–2013. The aim of this paper is to provide insight into the current

  9. Design and control of integrated styrene aniline production plant

    NARCIS (Netherlands)

    Partenie, O.; Van der Last, V.; Sorin Bildea, C.; Altimari, P.

    2009-01-01

    This paper illustrates the operational difficulties arising from simultaneously performing exothermic and endothermic reactions, and demonstrates that a plant can be built and safely operated by integrating the design and plantwide control issues. The behaviour of reactor – separation – recycle

  10. The design of high performance weak current integrated amplifier

    International Nuclear Information System (INIS)

    Chen Guojie; Cao Hui

    2005-01-01

    A design method of high performance weak current integrated amplifier using ICL7650 operational amplifier is introduced. The operating principle of circuits and the step of improving amplifier's performance are illustrated. Finally, the experimental results are given. The amplifier has programmable measurement range of 10 -9 -10 -12 A, automatic zero-correction, accurate measurement, and good stability. (authors)

  11. Human-Centered Design as an Integrating Discipline

    Directory of Open Access Journals (Sweden)

    Guy André Boy

    2017-02-01

    Full Text Available What is research today? Good research has to be indexed within appropriate mechanisms to be visible, considered and finally useful. These mechanisms are based on quantitative research methods and codes that are often very academic. Consequently, they impose rigorous constraints on the way results should be obtained and presented. In addition, everything people learn in academia needs to be graded. This leads to standard packaging of what should be learned and results in making people executants and not creators nor inventors. In other words, this academic standardization precludes freedom for innovation. This paper proposes Human-Centered Design (HCD as a solution to override these limitations and roadblocks. HCD involves expertise, experience, participation, modeling and simulation, complexity analysis and qualitative research. What is education today? Education is organized in silos with little attempt to integrate individual academic disciplines. Large system integration is almost never learned in engineering schools, and Human- Systems Integration (HSI even less. Instead, real-life problemsolving requires integration skills. What is design research? We often hear that design has nothing to do with research, and conversely. Putting design and research together, as complementary disciplines, contributes to combine creativity, rigorous demonstration and validation. This is somehow what HCD is about.

  12. Optical System Design and Integration of the Mercury Laser Altimeter

    Science.gov (United States)

    Ramos-Izquierdo, Luis; Scott, V. Stanley, III; Schmidt, Stephen; Britt, Jamie; Mamakos, William; Trunzo, Raymond; Cavanaugh, John; Miller, Roger

    2005-01-01

    The Mercury Laser Altimeter (MLA). developed for the 2004 MESSENGER mission to Mercury, is designed to measure the planet's topography via laser ranging. A description of the MLA optical system and its measured optical performance during instrument-level and spacecraft-level integration and testing are presented.

  13. Integrating ergonomics into engineering design: the role of objects.

    Science.gov (United States)

    Hall-Andersen, Lene Bjerg; Broberg, Ole

    2014-05-01

    The objective of this study was to explore the role of objects in integrating ergonomic knowledge in engineering design processes. An engineering design case was analyzed using the theoretical concepts of boundary objects and intermediary objects: Boundary objects facilitate collaboration between different knowledge domains, while the aim of an intermediary object is to circulate knowledge and thus produce a distant effect. Adjustable layout drawings served as boundary objects and had a positive impact on the dialog between an ergonomist and designers. An ergonomic guideline document was identified as an intermediary object. However, when the ergonomic guidelines were circulated in the design process, only some of the guidelines were transferred to the design of the sterile processing plant. Based on these findings, recommendations for working with objects in design processes are included. Copyright © 2013 Elsevier Ltd and The Ergonomics Society. All rights reserved.

  14. Integrated airfoil and blade design method for large wind turbines

    DEFF Research Database (Denmark)

    Zhu, Wei Jun; Shen, Wen Zhong

    2013-01-01

    This paper presents an integrated method for designing airfoil families of large wind turbine blades. For a given rotor diameter and tip speed ratio, the optimal airfoils are designed based on the local speed ratios. To achieve high power performance at low cost, the airfoils are designed...... with an objective of high Cp and small chord length. When the airfoils are obtained, the optimum flow angle and rotor solidity are calculated which forms the basic input to the blade design. The new airfoils are designed based on the previous in-house airfoil family which were optimized at a Reynolds number of 3...... million. A novel shape perturbation function is introduced to optimize the geometry on the existing airfoils and thus simplify the design procedure. The viscos/inviscid code Xfoil is used as the aerodynamic tool for airfoil optimization where the Reynolds number is set at 16 million with a free...

  15. Multidisciplinary management of chronic heart failure: principles and future trends.

    Science.gov (United States)

    Davidson, Patricia M; Newton, Phillip J; Tankumpuan, Thitipong; Paull, G; Dennison-Himmelfarb, Cheryl

    2015-10-01

    Globally, the management of chronic heart failure (CHF) challenges health systems. The high burden of disease and the costs associated with hospitalization adversely affect individuals, families, and society. Improved quality, access, efficiency, and equity of CHF care can be achieved by using multidisciplinary care approaches if there is adherence and fidelity to the program's elements. The goal of this article was to summarize evidence and make recommendations for advancing practice, education, research, and policy in the multidisciplinary management of patients with CHF. Essential elements of multidisciplinary management of CHF were identified from meta-analyses and clinical practice guidelines. The study factors were discussed from the perspective of the health care system, providers, patients, and their caregivers. Identified gaps in evidence were used to identify areas for future focus in CHF multidisciplinary management. Although there is high-level evidence (including several meta-analyses) for the efficacy of management programs for CHF, less evidence exists to determine the benefit attributable to individual program components or to identify the specific content of effective components and the manner of their delivery. Health care system, provider, and patient factors influence health care models and the effective management of CHF and require focus and attention. Extrapolating trial findings to clinical practice settings is limited by the heterogeneity of study populations and the implementation of models of intervention beyond academic health centers, where practice environments differ considerably. Ensuring that individual programs are both developed and assessed that consider these factors is integral to ensuring adherence and fidelity with the core dimensions of disease management necessary to optimize patient and organizational outcomes. Recognizing the complexity of the multidisciplinary CHF interventions will be important in advancing the design

  16. ITER design, integration and assembly studies assisted by virtual reality

    Energy Technology Data Exchange (ETDEWEB)

    Keller, D., E-mail: delphine.keller@cea.fr [CEA, IRFM, F-13108 St-Paul-Lez-Durance (France); ITER Organization, Route de Vinon-sur-Verdon, F-13115 St-Paul-Lez-Durance (France); Doceul, L.; Ferlay, F.; Jiolat, G. [CEA, IRFM, F-13108 St-Paul-Lez-Durance (France); Cordier, J.J.; Kuehn, I.; Manfreo, B.; Reich, J. [ITER Organization, Route de Vinon-sur-Verdon, F-13115 St-Paul-Lez-Durance (France)

    2013-10-15

    Highlights: ► VR technologies applied to Fusion enable to better and faster understand integration issues. ► Problems are solved and validated on a numerical mock up. ► Integration and accessibility issues can be identified in the earliest design. ► VR technologies are very helpful for assembly and maintenance operation simulations. ► New tools for real time simulations of hands-on operations are currently under development. -- Abstract: In a project like ITER where schedule, resources and cost is continuously optimized, emphasis has to be put on developing long lead items first while keeping other designs very low in definition. Hence, at a particular stage of the project, several components have to coexist in the integrated system while handling different level of maturity. Therefore, all the difficulty consists in managing the interfaces between all these components and to minimize the risk of design changes on the most advanced components. As a future exploitant, ITER is in charge of managing these interfaces and to ensure that maintenance of especially safety important class components (SIC) is feasible. These operation and maintenance constraints have to be taken into account since the earliest design of the components itselves. In this context, CEA IRFM is taking the benefit of using its virtual reality (VR) platform and simulation tools to assist ITER Organization in improving the efficiency of the inconsistencies identification and the machine sub-system design optimization. Currently, two contracts are on-going: the first one concerns the cryostat and in-vessel components; the second one concerns the overall Tokamak (TKM) and diagnostic buildings. This paper describes how VR tools applied to fusion and especially to ITER can help design and Integration with taking into account assembly and maintenance requirements at early stage in the design of complex systems.

  17. ITER design, integration and assembly studies assisted by virtual reality

    International Nuclear Information System (INIS)

    Keller, D.; Doceul, L.; Ferlay, F.; Jiolat, G.; Cordier, J.J.; Kuehn, I.; Manfreo, B.; Reich, J.

    2013-01-01

    Highlights: ► VR technologies applied to Fusion enable to better and faster understand integration issues. ► Problems are solved and validated on a numerical mock up. ► Integration and accessibility issues can be identified in the earliest design. ► VR technologies are very helpful for assembly and maintenance operation simulations. ► New tools for real time simulations of hands-on operations are currently under development. -- Abstract: In a project like ITER where schedule, resources and cost is continuously optimized, emphasis has to be put on developing long lead items first while keeping other designs very low in definition. Hence, at a particular stage of the project, several components have to coexist in the integrated system while handling different level of maturity. Therefore, all the difficulty consists in managing the interfaces between all these components and to minimize the risk of design changes on the most advanced components. As a future exploitant, ITER is in charge of managing these interfaces and to ensure that maintenance of especially safety important class components (SIC) is feasible. These operation and maintenance constraints have to be taken into account since the earliest design of the components itselves. In this context, CEA IRFM is taking the benefit of using its virtual reality (VR) platform and simulation tools to assist ITER Organization in improving the efficiency of the inconsistencies identification and the machine sub-system design optimization. Currently, two contracts are on-going: the first one concerns the cryostat and in-vessel components; the second one concerns the overall Tokamak (TKM) and diagnostic buildings. This paper describes how VR tools applied to fusion and especially to ITER can help design and Integration with taking into account assembly and maintenance requirements at early stage in the design of complex systems

  18. The design of a compact integral medium size PWR

    International Nuclear Information System (INIS)

    Shirvan, Koroush; Hejzlar, Pavel; Kazimi, Mujid S.

    2012-01-01

    Highlights: ► We model the IRIS reactor in RELAP5 and VIPRE codes. ► We use Printed Circuit Heat Exchangers and internally and externally cooled fuel pins in IRIS. ► We increase the IRIS power by 50% and demonstrate adequate safety performance. ► We show significant potential gain in economics for any integral PWR reactor design. - Abstract: Integral reactors have been proposed in recent years as a means to eliminate loss of coolant events, and reduce the number of large vessels of a nuclear power plant. In this paper the focus on how to further increase the power that can be derived from a given vessel volume. The example is applied to the International Reactor Innovative and Secure (IRIS), a medium size, light water reactor rated at 1000 MWt. The IRIS is an integral design containing all pumps and steam generators along with a traditional PWR core inside the reactor vessel. IRIS was designed with 8 Once-Through Helically Coiled Steam Generators (OTHSG), located above the core, in an annular region between the riser and the pressure vessel wall. This work examines ideas to increase its power output in the same vessel size while maintaining or improving the safety margins. The combination of Printed Circuit Heat Exchangers (PCHE) and Internally and EXternally cooled Annular Fuel (IXAF) is proposed to implement such improvement in otherwise the reference IRIS design. Safety implications of such steam generator and fuel design changes for the same reactor size are examined, under both steady state and transients, using the RELAP5 and VIPRE codes. It is found that the IRIS reactor power can be increased by 50% by using the PCHE and IXAF. The proposed design is found to be less expensive per unit electric power produced, these improvements and analyses can be applied to any integral reactor design.

  19. Biomedical data integration in computational drug design and bioinformatics.

    Science.gov (United States)

    Seoane, Jose A; Aguiar-Pulido, Vanessa; Munteanu, Cristian R; Rivero, Daniel; Rabunal, Juan R; Dorado, Julian; Pazos, Alejandro

    2013-03-01

    In recent years, in the post genomic era, more and more data is being generated by biological high throughput technologies, such as proteomics and transcriptomics. This omics data can be very useful, but the real challenge is to analyze all this data, as a whole, after integrating it. Biomedical data integration enables making queries to different, heterogeneous and distributed biomedical data sources. Data integration solutions can be very useful not only in the context of drug design, but also in biomedical information retrieval, clinical diagnosis, system biology, etc. In this review, we analyze the most common approaches to biomedical data integration, such as federated databases, data warehousing, multi-agent systems and semantic technology, as well as the solutions developed using these approaches in the past few years.

  20. Ship Design and Construction. An Integrated University Course

    DEFF Research Database (Denmark)

    Andersen, Poul; Jensen, Jørgen Juncher

    1996-01-01

    This paper describes an integrated course in design and construction of merchant ships taught at the Department of Naval Architecture andOffshore Engineering, the Technical University of Denmark. During the course, the students make a preliminary design of a ship of selected type and also design...... its engine room. The teaching combines lectures with laboratory work at the drawing tables and computer terminals. During the summer holiday, sea time on board ships of the relevant types are offered. Experienced naval architects from shipyards and ship consultancies give lectures and instructions...

  1. NSSS Component Control System Design of Integral Reactor

    International Nuclear Information System (INIS)

    Lee, Joon Koo; Kwon, Ho Je; Jeong, Kwong Il; Park, Heui Youn; Koo, In Soo

    2005-01-01

    MMIS(Man Machine Interface System) of an integral reactor is composed of a Control Room, Plant Protection System, Control System and Monitoring System which are related with the overall plant operation. MMIS is being developed with a new design concept and digital technology to reduce the Human Factor Error and improve the systems' safety, reliability and availability. And CCS(component control system) is also being developed with a new design concept and digital hardware technology A fully digitalized system and design concept are introduced in the NSSS CCS

  2. Preliminary design concepts of an advanced integral reactor

    International Nuclear Information System (INIS)

    Moon, Kap S.; Lee, Doo J.; Kim, Keung K.; Chang, Moon H.; Kim, Si H.

    1997-01-01

    An integral reactor on the basis of PWR technology is being conceptually developed at KAERI. Advanced technologies such as intrinsic and passive safety features are implemented in establishing the design concepts of the reactor to enhance the safety and performance. Research and development including laboratory-scale tests are concurrently underway for confirming the technical adoption of those concepts to the rector design. The power output of the reactor will be in the range of 100MWe to 600MWe which is relatively small compared to the existing loop type reactors. The detailed analysis to assure the design concepts is in progress. (author). 3 figs, 1 tab

  3. Integral Monitored Retrievable Storage (MRS) Facility conceptual design report

    International Nuclear Information System (INIS)

    1985-09-01

    The Basis for Design established the functional requirements and design criteria for an Integral Monitored Retrievable Storage (MRS) facility. The MRS Facility design, described in this report, is based on those requirements and includes all infrastructure, facilities, and equipment required to routinely receive, unload, prepare for storage, and store spent fuel (SF), high-level waste (HLW), and transuranic waste (TRU), and to decontaminate and return shipping casks received by both rail and truck. The facility is complete with all supporting facilities to make the MRS Facility a self-sufficient installation

  4. Analysis and Evaluation of Statistical Models for Integrated Circuits Design

    Directory of Open Access Journals (Sweden)

    Sáenz-Noval J.J.

    2011-10-01

    Full Text Available Statistical models for integrated circuits (IC allow us to estimate the percentage of acceptable devices in the batch before fabrication. Actually, Pelgrom is the statistical model most accepted in the industry; however it was derived from a micrometer technology, which does not guarantee reliability in nanometric manufacturing processes. This work considers three of the most relevant statistical models in the industry and evaluates their limitations and advantages in analog design, so that the designer has a better criterion to make a choice. Moreover, it shows how several statistical models can be used for each one of the stages and design purposes.

  5. Computer-integrated design and information management for nuclear projects

    International Nuclear Information System (INIS)

    Gonzalez, A.; Martin-Guirado, L.; Nebrera, F.

    1987-01-01

    Over the past seven years, Empresarios Agrupados has been developing a comprehensive, computer-integrated system to perform the majority of the engineering, design, procurement and construction management activities in nuclear, fossil-fired as well as hydro power plant projects. This system, which is already in a production environment, comprises a large number of computer programs and data bases designed using a modular approach. Each software module, dedicated to meeting the needs of a particular design group or project discipline, facilitates the performance of functional tasks characteristic of the power plant engineering process

  6. Strategically Integrated Design – Helping Brands to Keep Their Promises

    Directory of Open Access Journals (Sweden)

    Krohn Michael

    2015-11-01

    Full Text Available Many companies incorporate design into their processes much too late and work sequentially instead of in an integrated manner. If, however, the important conceptual, technical or market-relevant decisions have already been made and the product or service is almost ready for launch, then design “cosmetics” will not help much. Design creates images that stick in your mind, and if these images are thought out at the last minute, there’s a risk that they will not optimally promote the overall brand image.

  7. Integrated, multidisciplinary care for hand eczema: design of a randomized controlled trial and cost-effectiveness study.

    NARCIS (Netherlands)

    Gils, R.F. van; Valk, P.G.M. van der; Bruynzeel, D.; Coenraads, P.J.; Boot, C.R.L.; Mechelen, W. van; Anema, J.R.

    2009-01-01

    BACKGROUND: The individual and societal burden of hand eczema is high. Literature indicates that moderate to severe hand eczema is a disease with a poor prognosis. Many patients are hampered in their daily activities, including work. High costs are related to high medical consumption, productivity

  8. Design Development and Verification of a System Integrated Modular PWR

    International Nuclear Information System (INIS)

    Kim, S.-H.; Kim, K. K.; Chang, M. H.; Kang, C. S.; Park, G.-C.

    2002-01-01

    An advanced PWR with a rated thermal power of 330 MW has been developed at the Korea Atomic Energy Research Institute (KAERI) for a dual purpose: seawater desalination and electricity generation. The conceptual design of SMART ( System-Integrated Modular Advanced ReacTor) with a desalination system was already completed in March of 1999. The basic design for the integrated nuclear desalination system is currently underway and will be finished by March of 2002. The SMART co-generation plant with the MED seawater desalination process is designed to supply forty thousand (40,000) tons of fresh water per day and ninety (90) MW of electricity to an area with approximately a ten thousand (100,000) population or an industrialized complex. This paper describes advanced design features adopted in the SMART design and also introduces the design and engineering verification program. In the beginning stage of the SMART development, top-level requirements for safety and economics were imposed for the SMART design features. To meet the requirements, highly advanced design features enhancing the safety, reliability, performance, and operability are introduced in the SMART design. The SMART consists of proven KOFA (Korea Optimized Fuel Assembly), helical once-through steam generators, a self-controlled pressurizer, control element drive mechanisms, and main coolant pumps in a single pressure vessel. In order to enhance safety characteristics, innovative design features adopted in the SMART system are low core power density, large negative Moderator Temperature Coefficient (MTC), high natural circulation capability and integral arrangement to eliminate large break loss of coolant accident, etc. The progression of emergency situations into accidents is prevented with a number of advanced engineered safety features such as passive residual heat removal system, passive emergency core cooling system, safeguard vessel, and passive containment over-pressure protection. The preliminary

  9. Development of mechanical design technology for integral reactor

    International Nuclear Information System (INIS)

    Park, Keun Bae; Choi, Suhn; Kim, Kang Soo; Kim, Tae Wan; Jeong, Kyeong Hoon; Lee, Gyu Mahn; Kim, Jong Wook; Choi, Woo Seok

    2002-03-01

    This report is the final documentation of the 'Development of Mechanical Design Technology for Integral Reactor' which describes the design activities including reactor vessel assembly structural modelling, normal operation and transient analysis, preparation of design specification, major component stress analysis, evaluation of structural integrity, review of fabricability, maintenance and repair scheme, etc. To establish the design requirements and applicable codes and standards, each GDC criterion was reviewed regarding the SMART structural characteristics and design status, and then the applicability and point of issues were evaluated. To accomodate the result of the core optimization program, modification of pressure vessel and reactor internal components were carried out. SG nozzles were rearranged to penetrate the pressure vessel wall instead of the annular cover. Coolant flow path through the MCP impeller was revised and the adjacent structures were modified. Dynamic analysis model was developed reflecting all the structural changes to perform the seismic and BLPB analysis. Fracture mechanics evaluation on the structural integrity of the reactor pressure vessel was also conducted. Besides, equipment maintenance and replacement plan including the refueling scheme was discussed to confirm the embodiment of SMART through construction and operation

  10. Multidisciplinary Analysis of a Hypersonic Engine

    Science.gov (United States)

    Suresh, Ambady; Stewart, Mark

    2003-01-01

    The objective is to develop high fidelity tools that can influence ISTAR design In particular, tools for coupling Fluid-Thermal-Structural simulations RBCC/TBCC designers carefully balance aerodynamic, thermal, weight, & structural considerations; consistent multidisciplinary solutions reveal details (at modest cost) At Scram mode design point, simulations give details of inlet & combustor performance, thermal loads, structural deflections.

  11. Integrated Design Validation: Combining Simulation and Formal Verification for Digital Integrated Circuits

    Directory of Open Access Journals (Sweden)

    Lun Li

    2006-04-01

    Full Text Available The correct design of complex hardware continues to challenge engineers. Bugs in a design that are not uncovered in early design stages can be extremely expensive. Simulation is a predominantly used tool to validate a design in industry. Formal verification overcomes the weakness of exhaustive simulation by applying mathematical methodologies to validate a design. The work described here focuses upon a technique that integrates the best characteristics of both simulation and formal verification methods to provide an effective design validation tool, referred as Integrated Design Validation (IDV. The novelty in this approach consists of three components, circuit complexity analysis, partitioning based on design hierarchy, and coverage analysis. The circuit complexity analyzer and partitioning decompose a large design into sub-components and feed sub-components to different verification and/or simulation tools based upon known existing strengths of modern verification and simulation tools. The coverage analysis unit computes the coverage of design validation and improves the coverage by further partitioning. Various simulation and verification tools comprising IDV are evaluated and an example is used to illustrate the overall validation process. The overall process successfully validates the example to a high coverage rate within a short time. The experimental result shows that our approach is a very promising design validation method.

  12. An Integrated Methodology for Emulsified Formulated Product Design

    DEFF Research Database (Denmark)

    Mattei, Michele

    are mixed together to determine the desired emulsified product. They are still mainly designed and analysed through trial - and - error based exper- imental techniques, therefore a systematic approach , integrating model-based as well a s experiment - based techniques, for design of these products could......The consumer oriented chemical based products are used every day by millions of people. They are structured products constituted of numerous chemicals, and many of them, especially household and personal care products, are emulsions where active ingredients, solvents, additives and surfactants...... significantly reduce both time and cost connected to product development by doing only the necessary experi- ments , and ensuring chances for innovation . The main contribution of this project i s the development of an integrated methodology for the design of emulsified formulated products. The methodology...

  13. Safety design integrated in the Building Delivery System

    DEFF Research Database (Denmark)

    Jørgensen, Kirsten

    2012-01-01

    phases of the building delivery system by using the principle of the lean construction modelling. The method for the research was to go through the lean construction building delivery system step by step and create a normative description of what to do, when to do and how to do to fully integration...... of safety in each process. The group of participants who created the description had a high experience in a combination of research, safety and health in general and especial in construction and knowledge of the lean construction processes both from the clients perspective as well as from the designers...... and the consultants. The result is a concept and guideline including control schemes for how to integrate safety design in the lean construction building delivery system including what to do and when. The concept has been tested in an educational context and found useful by the designers. The practical value...

  14. Learning Multidisciplinary Collaboration with Games

    DEFF Research Database (Denmark)

    Henriksen, Thomas Duus

    2015-01-01

    This chapter describes the design of a game-based learning process for developing communication in public organisations. The game-design presented here emphasises those parts of public organisations that tend to employ multidisciplinary teams for solving wicked problems. As such teams employ...... members from different, professional backgrounds, the game Public Professional sought to develop new understandings among team members and across professions. The purpose of this game was to facilitate an understanding among team members and across professions, a game-based learning process named Public...... from the game’s core mechanics....

  15. Tour Guide Robots: An Integrated Research and Design Platform to Prepare Engineering and Technology Students

    Science.gov (United States)

    Yelamarthi, Kumar

    2016-01-01

    Many interesting research and design questions occur at the intersections of traditional disciplines, yet most coursework and research programs for undergraduate engineering students are focused on one discipline. This leads to underutilization of the potential in better preparing students through multidisciplinary projects. Identifying this…

  16. Vertical Integration of System-on-Chip Concepts in the Digital Design Curriculum

    Science.gov (United States)

    Tang, Ying; Head, L. M.; Ramachandran, R. P.; Chatman, L. M.

    2011-01-01

    The rapid evolution of System-on-Chip (SoC) challenges academic curricula to keep pace with multidisciplinary/interdisciplinary system thinking. This paper presents a curricular prototype that cuts across artificial course boundaries and provides a meaningful exploration of diverse facets of SoC design. Specifically, experimental contents of a…

  17. An integrated computer aided system for integrated design of chemical processes

    DEFF Research Database (Denmark)

    Gani, Rafiqul; Hytoft, Glen; Jaksland, Cecilia

    1997-01-01

    In this paper, an Integrated Computer Aided System (ICAS), which is particularly suitable for solving problems related to integrated design of chemical processes; is presented. ICAS features include a model generator (generation of problem specific models including model simplification and model ...... form the basis for the toolboxes. The available features of ICAS are highlighted through a case study involving the separation of binary azeotropic mixtures. (C) 1997 Elsevier Science Ltd....

  18. New ways of integrating material knowledge into the design process

    DEFF Research Database (Denmark)

    Højris, Anders; Nielsen, Louise Møller

    2013-01-01

    – based on technical performance, no longer apply. Accordingly the approach in this paper is to view information and knowledge about materials through the perspective of organizational memory and technology brokering. This paper is build upon two cases from the German based design studio: designaffairs...... libraries and thereby access to information on new material possibilities has also changed the way designers integrate knowledge about materials into the design process. This means that the traditional design process model, where the selection of materials takes place after the design of form and function...... in order to help clients to find the right material among hundreds of samples. Furthermore a number of material libraries have also been developed into online database, which provides detailed information about new material and makes the information accessible from almost everywhere. The access to material...

  19. Argentinean integrated small reactor design and scale economy analysis of integrated reactor

    International Nuclear Information System (INIS)

    Florido, P. C.; Bergallo, J. E.; Ishida, M. V.

    2000-01-01

    This paper describes the design of CAREM, which is Argentinean integrated small reactor project and the scale economy analysis results of integrated reactor. CAREM project consists on the development, design and construction of a small nuclear power plant. CAREM is an advanced reactor conceived with new generation design solutions and standing on the large experience accumulated in the safe operation of Light Water Reactors. The CAREM is an indirect cycle reactor with some distinctive and characteristic features that greatly simplify the reactor and also contribute to a highly level of safety: integrated primary cooling system, self pressurized, primary cooling by natural circulation and safety system relying on passive features. For a fully doupled economic evaluation of integrated reactors done by IREP (Integrated Reactor Evaluation Program) code transferred to IAEA, CAREM have been used as a reference point. The results shows that integrated reactors become competitive with power larger than 200MWe with Argentinean cheapest electricity option. Due to reactor pressure vessel construction limit, low pressure drop steam generator are used to reach power output of 200MWe for natural circulation. For forced circulation, 300MWe can be achieved. (author)

  20. Sustainable Design Re-Examined: Integrated Approach to Knowledge Creation for Sustainable Interior Design

    Science.gov (United States)

    Lee, Young S.

    2014-01-01

    The article focuses on a systematic approach to the instructional framework to incorporate three aspects of sustainable design. It also aims to provide an instruction model for sustainable design stressing a collective effort to advance knowledge creation as a community. It develops a framework conjoining the concept of integrated process in…

  1. Multidisciplinary Collaborative Care for Depressive Disorder in the Occupational Health Setting: design of a randomised controlled trial and cost-effectiveness study

    Directory of Open Access Journals (Sweden)

    Beekman Aartjan TF

    2008-05-01

    Full Text Available Abstract Background Major depressive disorder (MDD has major consequences for both patients and society, particularly in terms of needlessly long sick leave and reduced functioning. Although evidence-based treatments for MDD are available, they show disappointing results when implemented in daily practice. A focus on work is also lacking in the treatment of depressive disorder as well as communication of general practitioners (GPs and other health care professionals with occupational physicians (OPs. The OP may play a more important role in the recovery of patients with MDD. Purpose of the present study is to tackle these obstacles by applying a collaborative care model, which has proven to be effective in the USA, with a focus on return to work (RTW. From a societal perspective, the (costeffectiveness of this collaborative care treatment, as a way of transmural care, will be evaluated in depressed patients on sick leave in the occupational health setting. Methods/Design A randomised controlled trial in which the treatment of MDD in the occupational health setting will be evaluated in the Netherlands. A transmural collaborative care model, including Problem Solving Treatment (PST, a workplace intervention, antidepressant medication and manual guided self-help will be compared with care as usual (CAU. 126 Patients with MDD on sick leave between 4 and 12 weeks will be included in the study. Care in the intervention group will be provided by a multidisciplinary team of a trained OP-care manager and a consultant psychiatrist. The treatment is separated from the sickness certification. Data will be collected by means of questionnaires at baseline and at 3, 6, 9 and 12 months after baseline. Primary outcome measure is reduction of depressive symptoms, secondary outcome measure is time to RTW, tertiary outcome measure is the cost effectiveness. Discussion The high burden of MDD and the high level of sickness absence among people with MDD contribute to

  2. Design optimization of radiation-hardened CMOS integrated circuits

    International Nuclear Information System (INIS)

    1975-01-01

    Ionizing-radiation-induced threshold voltage shifts in CMOS integrated circuits will drastically degrade circuit performance unless the design parameters related to the fabrication process are properly chosen. To formulate an approach to CMOS design optimization, experimentally observed analytical relationships showing strong dependences between threshold voltage shifts and silicon dioxide thickness are utilized. These measurements were made using radiation-hardened aluminum-gate CMOS inverter circuits and have been corroborated by independent data taken from MOS capacitor structures. Knowledge of these relationships allows one to define ranges of acceptable CMOS design parameters based upon radiation-hardening capabilities and post-irradiation performance specifications. Furthermore, they permit actual design optimization of CMOS integrated circuits which results in optimum pre- and post-irradiation performance with respect to speed, noise margins, and quiescent power consumption. Theoretical and experimental results of these procedures, the applications of which can mean the difference between failure and success of a CMOS integrated circuit in a radiation environment, are presented

  3. Lightweight structure design for wind energy by integrating nanostructured materials

    International Nuclear Information System (INIS)

    Li, Ying; Lu, Jian

    2014-01-01

    Highlights: • Integrate high-strength nano-materials into lightweight design. • Lightweight design scheme for wind turbine tower application. • Expand the bending formulae for tapered tubular structures with varying thickness. • We rewrite the Secant Formula for a tapered beam under eccentric compression. - Abstract: Wind power develops very fast nowadays with high expectation. Although at the mean time, the use of taller towers, however, smacks head-on into the issue of transportability. The engineering base and computational tools have to be developed to match machine size and volume. Consequently the research on the light weight structures of tower is carrying out in the main countries which are actively developing wind energy. This paper reports a new design scheme of light weight structure for wind turbine tower. This design scheme is based on the integration of the nanostructured materials produced by the Surface Mechanical Attrition Treatment (SMAT) process. The objective of this study is to accomplish the weight reduction by optimizing the wall thickness of the tapered tubular structure. The basic methods include the identification of the critical zones and the distribution of the high strength materials according to different necessities. The equivalent strength or stiffness design method and the high strength material properties after SMAT process are combined together. Bending and buckling are two main kinds of static loads concerned in consideration. The study results reveal that there is still enough margin for weight reduction in the traditional wind turbine tower design

  4. Integrated design optimization research and development in an industrial environment

    Science.gov (United States)

    Kumar, V.; German, Marjorie D.; Lee, S.-J.

    1989-01-01

    An overview is given of a design optimization project that is in progress at the GE Research and Development Center for the past few years. The objective of this project is to develop a methodology and a software system for design automation and optimization of structural/mechanical components and systems. The effort focuses on research and development issues and also on optimization applications that can be related to real-life industrial design problems. The overall technical approach is based on integration of numerical optimization techniques, finite element methods, CAE and software engineering, and artificial intelligence/expert systems (AI/ES) concepts. The role of each of these engineering technologies in the development of a unified design methodology is illustrated. A software system DESIGN-OPT has been developed for both size and shape optimization of structural components subjected to static as well as dynamic loadings. By integrating this software with an automatic mesh generator, a geometric modeler and an attribute specification computer code, a software module SHAPE-OPT has been developed for shape optimization. Details of these software packages together with their applications to some 2- and 3-dimensional design problems are described.

  5. How Multidisciplinary Are the Multidisciplinary Journals Science and Nature?

    Science.gov (United States)

    Solomon, Gregg E A; Carley, Stephen; Porter, Alan L

    2016-01-01

    Interest in cross-disciplinary research knowledge interchange runs high. Review processes at funding agencies, such as the U.S. National Science Foundation, consider plans to disseminate research across disciplinary bounds. Publication in the leading multidisciplinary journals, Nature and Science, may signify the epitome of successful interdisciplinary integration of research knowledge and cross-disciplinary dissemination of findings. But how interdisciplinary are they? The journals are multidisciplinary, but do the individual articles themselves draw upon multiple fields of knowledge and does their influence span disciplines? This research compares articles in three fields (Cell Biology, Physical Chemistry, and Cognitive Science) published in a leading disciplinary journal in each field to those published in Nature and Science. We find comparable degrees of interdisciplinary integration and only modest differences in cross-disciplinary diffusion. That said, though the rate of out-of-field diffusion might be comparable, the sheer reach of Nature and Science, indicated by their potent Journal Impact Factors, means that the diffusion of knowledge therein can far exceed that of leading disciplinary journals in some fields (such as Physical Chemistry and Cognitive Science in our samples).

  6. How Multidisciplinary Are the Multidisciplinary Journals Science and Nature?

    Science.gov (United States)

    Solomon, Gregg E. A.; Carley, Stephen; Porter, Alan L.

    2016-01-01

    Interest in cross-disciplinary research knowledge interchange runs high. Review processes at funding agencies, such as the U.S. National Science Foundation, consider plans to disseminate research across disciplinary bounds. Publication in the leading multidisciplinary journals, Nature and Science, may signify the epitome of successful interdisciplinary integration of research knowledge and cross-disciplinary dissemination of findings. But how interdisciplinary are they? The journals are multidisciplinary, but do the individual articles themselves draw upon multiple fields of knowledge and does their influence span disciplines? This research compares articles in three fields (Cell Biology, Physical Chemistry, and Cognitive Science) published in a leading disciplinary journal in each field to those published in Nature and Science. We find comparable degrees of interdisciplinary integration and only modest differences in cross-disciplinary diffusion. That said, though the rate of out-of-field diffusion might be comparable, the sheer reach of Nature and Science, indicated by their potent Journal Impact Factors, means that the diffusion of knowledge therein can far exceed that of leading disciplinary journals in some fields (such as Physical Chemistry and Cognitive Science in our samples). PMID:27043924

  7. Bringing service design to manufacturing companies: integrating PSS and service design approaches

    DEFF Research Database (Denmark)

    Costa, Nina; Patrício, Lia; Morelli, Nicola

    2018-01-01

    in a manufacturing industry. This paper details how the application supports the design of product–service system solutions from the exploration to the implementation stages, highlighting the physical evidence of service, and contributes to advance design research at the intersection of PSS and Service Design.......Manufacturing companies increasingly try to innovate in their offers to consumers by creating more complete solutions that combine product and service components. However, shifting from a product-centric perspective to a solution-oriented perspective is challenging. The present study adopted...... a design research methodology and built on Service-Dominant logic, integrating the human-oriented perspective of Service Design with an organizational network-oriented perspective of Product–Service System. It creates a new Integrative PSS approach, evolves design models, and provides an application...

  8. Design Integration - a theroretical and empirical study of design integration in small and medium sized Danish companies

    DEFF Research Database (Denmark)

    Erichsen, Pia Geisby

    er drivkræft. Afhandlingen bidrager til design management feltet med en ny måde at tale om og forstå design integration. Yderligere bidrager den med ny viden omkring dynamikken omkring design integration. Sidst men ikke mindst biddrager den til, at designledelseskonsulenter samt små og mellemstore...... organisatorisk kontekst?’ - blev søgt besvaret gennem to litteraturstudier af henholdsvis design management og design. Litteraturstudiet af design management gav imidlertid kun begrænsede svar på spørgsmålet ’hvad er design?’. Designfeltet derimod kunne give et mere nuanceret svar, hvilket resulterede i en ny...... blev det identificeret, at det var relevant, at se på barrierer og drivkræfter et dynamisk perspektiv. Via observationsstudiet blev designtrappen identificeret som relevant i forhold til forskningsspørgsmålet, men modellen havde også nogle indbyggede barrierer, hvorfor der blev søgt efter andre...

  9. Concise Review: Organ Engineering: Design, Technology, and Integration.

    Science.gov (United States)

    Kaushik, Gaurav; Leijten, Jeroen; Khademhosseini, Ali

    2017-01-01

    Engineering complex tissues and whole organs has the potential to dramatically impact translational medicine in several avenues. Organ engineering is a discipline that integrates biological knowledge of embryological development, anatomy, physiology, and cellular interactions with enabling technologies including biocompatible biomaterials and biofabrication platforms such as three-dimensional bioprinting. When engineering complex tissues and organs, core design principles must be taken into account, such as the structure-function relationship, biochemical signaling, mechanics, gradients, and spatial constraints. Technological advances in biomaterials, biofabrication, and biomedical imaging allow for in vitro control of these factors to recreate in vivo phenomena. Finally, organ engineering emerges as an integration of biological design and technical rigor. An overall workflow for organ engineering and guiding technology to advance biology as well as a perspective on necessary future iterations in the field is discussed. Stem Cells 2017;35:51-60. © 2016 AlphaMed Press.

  10. Computer graphics application in the engineering design integration system

    Science.gov (United States)

    Glatt, C. R.; Abel, R. W.; Hirsch, G. N.; Alford, G. E.; Colquitt, W. N.; Stewart, W. A.

    1975-01-01

    The computer graphics aspect of the Engineering Design Integration (EDIN) system and its application to design problems were discussed. Three basic types of computer graphics may be used with the EDIN system for the evaluation of aerospace vehicles preliminary designs: offline graphics systems using vellum-inking or photographic processes, online graphics systems characterized by direct coupled low cost storage tube terminals with limited interactive capabilities, and a minicomputer based refresh terminal offering highly interactive capabilities. The offline line systems are characterized by high quality (resolution better than 0.254 mm) and slow turnaround (one to four days). The online systems are characterized by low cost, instant visualization of the computer results, slow line speed (300 BAUD), poor hard copy, and the early limitations on vector graphic input capabilities. The recent acquisition of the Adage 330 Graphic Display system has greatly enhanced the potential for interactive computer aided design.

  11. Integrating chemical engineering fundamentals in the capstone process design project

    DEFF Research Database (Denmark)

    von Solms, Nicolas; Woodley, John; Johnsson, Jan Erik

    2010-01-01

    Reaction Engineering. In order to incorporate reactor design into process design in a meaningful way, the teachers of the respective courses need to collaborate (Standard 9 – Enhancement of Faculty CDIO skills). The students also see that different components of the chemical engineering curriculum relate......All B.Eng. courses offered at the Technical University of Denmark (DTU) must now follow CDIO standards. The final “capstone” course in the B.Eng. education is Process Design, which for many years has been typical of chemical engineering curricula worldwide. The course at DTU typically has about 30...... of the CDIO standards – especially standard 3 – Integrated Curriculum - means that the course projects must draw on competences provided in other subjects which the students are taking in parallel with Process Design – specifically Process Control and Reaction Engineering. In each semester of the B...

  12. Integrated Human Factors Design Guidelines for Sound Interface

    International Nuclear Information System (INIS)

    Lee, Jung Woon; Lee, Yong Hee; Oh, In Seok; Lee, Hyun Chul; Cha, Woo Chang

    2004-05-01

    Digital MMI, such as CRT, LCD etc., has been used increasingly in the design of main control room of the Korean standard nuclear power plants following the YGN units 3 and 4. The utilization of digital MMI may introduce various kind of sound interface into the control room design. In this project, for five top-level guideline items, including Sound Formats, Alarms, Sound Controls, Communications, and Environments, a total of 147 detail guidelines were developed and a database system for these guidelines was developed. The integrated human factors design guidelines for sound interface and the database system developed in this project will be useful for the design of sound interface of digital MMI in Korean NPPs

  13. Integrated Human Factors Design Guidelines for Sound Interface

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Jung Woon; Lee, Yong Hee; Oh, In Seok; Lee, Hyun Chul [KAERI, Daejeon (Korea, Republic of); Cha, Woo Chang [Kumoh National Univ. of Technology, Gumi (Korea, Republic of)

    2004-05-15

    Digital MMI, such as CRT, LCD etc., has been used increasingly in the design of main control room of the Korean standard nuclear power plants following the YGN units 3 and 4. The utilization of digital MMI may introduce various kind of sound interface into the control room design. In this project, for five top-level guideline items, including Sound Formats, Alarms, Sound Controls, Communications, and Environments, a total of 147 detail guidelines were developed and a database system for these guidelines was developed. The integrated human factors design guidelines for sound interface and the database system developed in this project will be useful for the design of sound interface of digital MMI in Korean NPPs.

  14. Trends in integrated circuit design for particle physics experiments

    International Nuclear Information System (INIS)

    Atkin, E V

    2017-01-01

    Integrated circuits are one of the key complex units available to designers of multichannel detector setups. A whole number of factors makes Application Specific Integrated Circuits (ASICs) valuable for Particle Physics and Astrophysics experiments. Among them the most important ones are: integration scale, low power dissipation, radiation tolerance. In order to make possible future experiments in the intensity, cosmic, and energy frontiers today ASICs should provide new level of functionality at a new set of constraints and trade-offs, like low-noise high-dynamic range amplification and pulse shaping, high-speed waveform sampling, low power digitization, fast digital data processing, serialization and data transmission. All integrated circuits, necessary for physical instrumentation, should be radiation tolerant at an earlier not reached level (hundreds of Mrad) of total ionizing dose and allow minute almost 3D assemblies. The paper is based on literary source analysis and presents an overview of the state of the art and trends in nowadays chip design, using partially own ASIC lab experience. That shows a next stage of ising micro- and nanoelectronics in physical instrumentation. (paper)

  15. Integrated design approach of the pebble bed modular using models

    International Nuclear Information System (INIS)

    Venter, P.J.

    2005-01-01

    The Pebble Bed Modular Reactor (PBMR) is the first pebble bed reactor that will be utilised in a high temperature direct Brayton cycle configuration. This implies that there are a number of unique features in the PBMR that extend from the German experience base. One of the challenges in the design of the PBMR is managing the integrated design process between the designers, the physicists and the analysts. This integrated design process is managed through model-based development work. Three-dimensional CAD models are constructed of the components and parts in the reactor. From the CAD models, CFD models, neutronic models, shielding models, FEM models and other thermodynamic models are derived. These models range from very simple models to extremely detailed and complex models. The models are used in legacy software as well as commercial off-the-shelf software. The different models are also used in code-to-code comparisons to verify the results. This paper will briefly discuss the different models and the interaction between the models, showing the iterative design process that is used in the development of the reactor at PBMR. (author)

  16. DESIGN ANALYSIS OF ELECTRICAL MACHINES THROUGH INTEGRATED NUMERICAL APPROACH

    Directory of Open Access Journals (Sweden)

    ARAVIND C.V.

    2016-02-01

    Full Text Available An integrated design platform for the newer type of machines is presented in this work. The machine parameters are evaluated out using developed modelling tool. With the machine parameters, the machine is modelled using computer aided tool. The designed machine is brought to simulation tool to perform electromagnetic and electromechanical analysis. In the simulation, conditions setting are performed to setup the materials, meshes, rotational speed and the excitation circuit. Electromagnetic analysis is carried out to predict the behavior of the machine based on the movement of flux in the machines. Besides, electromechanical analysis is carried out to analyse the speed-torque characteristic, the current-torque characteristic and the phase angle-torque characteristic. After all the results are analysed, the designed machine is used to generate S block function that is compatible with MATLAB/SIMULINK tool for the dynamic operational characteristics. This allows the integration of existing drive system into the new machines designed in the modelling tool. An example of the machine design is presented to validate the usage of such a tool.

  17. High Fidelity Multidisciplinary Tool Development for Helicopter Quieting

    National Research Council Canada - National Science Library

    Chen, Chung-Lung; Chen, Ya-Chi; Chen, Bing; Jain, Rohit; Lund, Tom; Zhao, Hongwu; Wang, Z.-J; Sun, Yuzhi; Saberi, Hossein; Shih, T.-H

    2007-01-01

    .... The problem is indeed multidisciplinary. Current helicopter blade designers use computational models, which depend heavily on experimental data and cannot be used to predict any novel design, which is a significant departure from existing designs...

  18. The Aged Residential Care Healthcare Utilization Study (ARCHUS): a multidisciplinary, cluster randomized controlled trial designed to reduce acute avoidable hospitalizations from long-term care facilities.

    Science.gov (United States)

    Connolly, Martin J; Boyd, Michal; Broad, Joanna B; Kerse, Ngaire; Lumley, Thomas; Whitehead, Noeline; Foster, Susan

    2015-01-01

    To assess effect of a complex, multidisciplinary intervention aimed at reducing avoidable acute hospitalization of residents of residential aged care (RAC) facilities. Cluster randomized controlled trial. RAC facilities with higher than expected hospitalizations in Auckland, New Zealand, were recruited and randomized to intervention or control. A total of 1998 residents of 18 intervention facilities and 18 control facilities. A facility-based complex intervention of 9 months' duration. The intervention comprised gerontology nurse specialist (GNS)-led staff education, facility bench-marking, GNS resident review, and multidisciplinary (geriatrician, primary-care physician, pharmacist, GNS, and facility nurse) discussion of residents selected using standard criteria. Primary end point was avoidable hospitalizations. Secondary end points were all acute admissions, mortality, and acute bed-days. Follow-up was for a total of 14 months. The intervention did not affect main study end points: number of acute avoidable hospital admissions (RR 1.07; 95% CI 0.85-1.36; P = .59) or mortality (RR 1.11; 95% CI 0.76-1.61; P = .62). This multidisciplinary intervention, packaging selected case review, and staff education had no overall impact on acute hospital admissions or mortality. This may have considerable implications for resourcing in the acute and RAC sectors in the face of population aging. Australian and New Zealand Clinical Trials Registry (ACTRN12611000187943). Copyright © 2015 AMDA – The Society for Post-Acute and Long-Term Care Medicine. Published by Elsevier Inc. All rights reserved.

  19. Supplier integration for new product developments: antecedents for supplier integration in modular product designs

    NARCIS (Netherlands)

    Eggers, Justus Erich

    2016-01-01

    Original equipment manufacturers (OEMs) increasingly integrate supplier resources in new product developments (NPD) to overcome bottlenecks of resource and to create competitive advantages. At the same time, OEMs react to the new market challenges by implementing modular product designs. Despite the

  20. Integration of distributed system simulation tools for a holistic approach to integrated building and system design

    NARCIS (Netherlands)

    Radosevic, M.; Hensen, J.L.M.; Wijsman, A.J.T.M.; Hensen, J.L.M.; Lain, M.

    2004-01-01

    Advanced architectural developments require an integrated approach to design where simulation tools available today deal. only with a small subset of the overall problem. The aim of this study is to enable run time exchange of necessary data at suitable frequency between different simulation

  1. The design features of integrated modular water reactor (IMR)

    International Nuclear Information System (INIS)

    Kanagawa, T.; Goto, M.; Usui, S.; Suzuta, T.; Serizawa, A.; Kunugi, T.; Yamauchi, T.; Itoh, G.; Matsumura, T.

    2004-01-01

    Small-to-medium-sized (300-600 MWe) reactors are required for the electric power market in the near future (2010-2030). The main theme in the development of small-to-medium-sized reactor is how to realize competitive cost against other energy sources. As measures to this disadvantage, greatly simplified and small-scale design is needed. From such point of view, Integrated Modular Water Reactor (IMR), whose electric output power is 350 MWe, adopts integrated and high temperature two-phase natural circulation system for the primary system. In this design, main coolant pipes, a pressurizer, and reactor coolant pumps are not needed, and the sizes of the reactor vessel and steam generators are minimized. Additionally, to enhance the economy of the whole plant, fluid systems, and Instrumentation and Control systems of IMR have also been reviewed to make them simplest and smallest taking the advantage of the IMR concept and the state of the art technologies. For example, the integrated primary system and the stand-alone direct heat removal system make the safety system very simple, i.e., no injection, no containment spray, no emergency AC power, etc. The chemical and volume control system is also simplified by eliminating the boron control system and the seal water system of reactor coolant pumps. In this paper, the status of the IMR development and the outline of the IMR design efforts to achieve the simplest and smallest plant are presented. (authors)

  2. Safeguards-by-Design: An Element of 3S Integration

    International Nuclear Information System (INIS)

    Bean, R.S.; Bjornard, T.A.; Hebdich, D.J.

    2009-01-01

    In 2008, the '20/20 Vision for the Future' background report by the IAEA Director General identified the possibility of integrating certain activities related to safeguards, safety, and security. Later in the year, the independent Commission report prepared at the request of the IAEA Director General noted that the Agency's's roles in nuclear safeguards, safety, and security (3S) complement and can mutually reinforce each other. Safeguards-by-design (SBD) is a practical measure that strengthens 3S integration, especially for the stage of nuclear facility design and construction, but also with ramifications for other stages of the facility life-cycle. This paper describes the SBD concept, with examples for diverse regulatory environments, being developed in the U.S under the U.S. Department of Energy (DOE) Next Generation Safeguards Initiative and the Advanced Fuel Cycle Initiative. This is compared with related international SBD work performed in the recent IAEA workshop on 'Facility Design and Plant Operation Features that Facilitate the Implementation of IAEA Safeguards'. Potential future directions for further development of SBD and its integration within 3S are identified.

  3. White Paper Report of the 2011 RAD-AID Conference on International Radiology for Developing Countries: Integrating Multidisciplinary Strategies for Imaging Services in the Developing World

    Science.gov (United States)

    Mazal, Jonathan; Lexa, Frank; Starikovsky, Anna; Jimenez, Pablo; Jain, Sanjay; DeStigter, Kristen K.; Nathan, Robert; Krebs, Elizabeth; Noble, Vicki; Marks, William; Hirsh, Richard N.; Short, Brad; Sydnor, Ryan; Timmreck-Jackson, Emily; Lungren, Matthew P.; Maxfield, Charles; Azene, Ezana M.; Garra, Brian S.; Choi, Brian G.; Lewin, Jonathan S.; Mollura, Daniel J.

    2016-01-01

    The 2011 RAD-AID Conference on International Radiology for Developing Countries discussed data, experiences and models pertaining to radiology in the developing world, where widespread shortages of imaging services significantly reduce health care quality and increase health care disparity. This white paper from the 2011 RAD-AID Conference represents consensus advocacy of multidisciplinary strategies to improve planning, accessibility and quality of imaging services in the developing world. Conference presenters and participants discussed numerous solutions to imaging and healthcare disparities including: (1) economic development for radiology service planning, (2) public health mechanisms to address disease and prevention at the population and community levels, (3) comparative clinical models to implement various clinical and workflow strategies adapted to unique developing world community contexts, (4) education to improve training and optimize service quality, and (5) technology innovation to bring new technical capabilities to limited-resource regions. PMID:22748790

  4. Designing to target cost: one approach to design/construction integration

    DEFF Research Database (Denmark)

    Jørgensen, Bo

    2005-01-01

    One approach to a more integrated construction delivery process is the concept of ‘designing to target cost’ of which the first examples of application within a lean construction framework have recently been seen. This paper introduces the main principles of the design to target cost method...... and discusses the applicability of this approach to construction. The low degree of organizational and technical continuity from one construction project to the next limits the applicability of the design for target cost approach when compared to its origin in product development of mass manufactured artefacts....... It can be argued that design to target cost may also provide a frame for developing the supply chain towards better coordination and collaboration. Thus methods of design to target cost may serve to facilitate the development of a more integrated supply chain....

  5. An integrated knowledge-based framework for synthesis and design of enterprise-wide processing networks

    DEFF Research Database (Denmark)

    Sin, Gürkan

    material, product portfolio and process technology selection for a given market scenario, their sustainability metrics and risk of investment under market uncertainties enabling risk-aware decision making. The framework is highlighted with successful applications for soybean oil processing (food technology......, the synthesis and design of processing networks is a complex and multidisciplinary problem, which involves many strategic and tactical decisions at business (considering financial criteria, market competition, supply chain network, etc) and engineering levels (considering synthesis, design and optimization...

  6. Stochastic simulation and robust design optimization of integrated photonic filters

    Directory of Open Access Journals (Sweden)

    Weng Tsui-Wei

    2016-07-01

    Full Text Available Manufacturing variations are becoming an unavoidable issue in modern fabrication processes; therefore, it is crucial to be able to include stochastic uncertainties in the design phase. In this paper, integrated photonic coupled ring resonator filters are considered as an example of significant interest. The sparsity structure in photonic circuits is exploited to construct a sparse combined generalized polynomial chaos model, which is then used to analyze related statistics and perform robust design optimization. Simulation results show that the optimized circuits are more robust to fabrication process variations and achieve a reduction of 11%–35% in the mean square errors of the 3 dB bandwidth compared to unoptimized nominal designs.

  7. Integrating Emotional Attachment and Sustainability in Electronic Product Design

    Directory of Open Access Journals (Sweden)

    Alex Lobos

    2013-03-01

    Full Text Available Current models for Information and Communication Technology (ICT products encourage frequent product replacement with newer versions that offer only minor incremental improvements. This pattern, named planned obsolescence, diminishes user experience and shortens product lifespan. This paper presents the conceptual basis for a two-part integrated approach to combating planned obsolescence in ICT devices. First, design for emotional attachment, which creates products that users enjoy, value, and use for longer. Second, technological adaptability, which anticipates product upgrades and repairs as new technologies emerge. A model interdisciplinary design course in industrial design and sustainability, also described herein, trains students to apply this approach to create innovative ICT products with smaller environmental footprints.

  8. How can design approaches be integrated into entrepreneurship education?

    DEFF Research Database (Denmark)

    Færgemann, Helle Meibom; Nørgård, Rikke Toft; Robinson, Sarah

    reflection about the intention and how the elements fit with the entrepreneurship field. The proposed process model presented (Fig 3) primarily has potential to strengthen the awareness of the need to alternate between divergence and convergence many times through an entrepreneurial process. Apart from......Questions we care about: When educating students through entrepreneurship we are interested in how can design approaches and processes be integrated into Entrepreneurship Education and what effect does this have on entrepreneurial learning? Approach: This is a conceptual paper which draws on data...... from a classic entrepreneurship course (mix of for- and through-approach) as well as a classic design course. Furthermore data from the iterative development of an entrepreneurship course with substantial design elements is a key data source. Overall, products and processes in the course have been...

  9. Software features and applications in process design, integration and operation

    Energy Technology Data Exchange (ETDEWEB)

    Dhole, V. [Aspen Tech Limited, Warrington (United Kingdom)

    1999-02-01

    Process engineering technologies and tools have evolved rapidly over the last twenty years. Process simulation/modeling, advanced process control, on-line optimisation, production planning and supply chain management are some of the examples of technologies that have rapidly matured from early commercial prototypes and concepts to established tools with significant impact on profitability of process industry today. Process Synthesis or Process Integration (PI) in comparison is yet to create its impact and still remains largely in the domain of few expert users. One of the key reasons as to why PI has not taken off is because the PI tools have not become integral components of the standard process engineering environments. On the last 15 years AspenTech has grown from a small process simulation tool provider to a large multinational company providing a complete suite of process engineering technologies and services covering process design, operation, planning and supply chain management. Throughout this period, AspenTech has acquired experience in rapidly evolving technologies from their early prototype stage to mature products and services. The paper outlines AspenTech`s strategy of integrating PI with other more established process design and operational improvement technologies. The paper illustrates the key elements of AspenTech`s strategy via examples of software development initiatives and services projects. The paper also outlines AspenTech`s future vision of the role of PI in process engineering. (au)

  10. Development of fluid system design technology for integral reactor

    Energy Technology Data Exchange (ETDEWEB)

    Lee, D. J.; Chang, M. H.; Kang, D. J. and others

    1999-03-01

    This study presents the technology development of the system design concepts of SMART, a multi-purposed integral reactor with enhanced safety and operability, for use in diverse usages and applications of the nuclear energy. This report contains the following; - Design characteristics - Performance and safety related design criteria - System description: Primary system, Secondary system, Residual heat removal system, Make-up system, Component cooling system, Safety system - Development of design computer code: Steam generator performance(ONCESG), Pressurizer performance(COLDPZR), Steam generator flow instability(SGINS) - Development of component module and modeling using MMS computer code - Design calculation: Steam generator thermal sizing, Analysis of feed-water temperature increase at a low flow rate, Evaluation of thermal efficiency in the secondary system, Inlet orifice throttling coefficient for the prevention of steam generator flow instability, Analysis of Nitrogen gas temperature in the pressurizer during heat-up process, evaluation of water chemistry and erosion etc. The results of this study can be utilized not only for the foundation technology of the next phase basic system design of the SMART but also for the basic model in optimizing the system concepts for future advanced reactors. (author)

  11. Accurate Complex Systems Design: Integrating Serious Games with Petri Nets

    Directory of Open Access Journals (Sweden)

    Kirsten Sinclair

    2016-03-01

    Full Text Available Difficulty understanding the large number of interactions involved in complex systems makes their successful engineering a problem. Petri Nets are one graphical modelling technique used to describe and check proposed designs of complex systems thoroughly. While automatic analysis capabilities of Petri Nets are useful, their visual form is less so, particularly for communicating the design they represent. In engineering projects, this can lead to a gap in communications between people with different areas of expertise, negatively impacting achieving accurate designs.In contrast, although capable of representing a variety of real and imaginary objects effectively, behaviour of serious games can only be analysed manually through interactive simulation. This paper examines combining the complementary strengths of Petri Nets and serious games. The novel contribution of this work is a serious game prototype of a complex system design that has been checked thoroughly. Underpinned by Petri Net analysis, the serious game can be used as a high-level interface to communicate and refine the design.Improvement of a complex system design is demonstrated by applying the integration to a proof-of-concept case study.   

  12. Social research design: framework for integrating philosophical and practical elements.

    Science.gov (United States)

    Cunningham, Kathryn Burns

    2014-09-01

    To provide and elucidate a comprehensible framework for the design of social research. An abundance of information exists concerning the process of designing social research. The overall message that can be gleaned is that numerable elements - both philosophical (ontological and epistemological assumptions and theoretical perspective) and practical (issue to be addressed, purpose, aims and research questions) - are influential in the process of selecting a research methodology and methods, and that these elements and their inter-relationships must be considered and explicated to ensure a coherent research design that enables well-founded and meaningful conclusions. There is a lack of guidance concerning the integration of practical and philosophical elements, hindering their consideration and explication. The author's PhD research into loneliness and cancer. This is a methodology paper. A guiding framework that incorporates all of the philosophical and practical elements influential in social research design is presented. The chronological and informative relationships between the elements are discussed. The framework presented can be used by social researchers to consider and explicate the practical and philosophical elements influential in the selection of a methodology and methods. It is hoped that the framework presented will aid social researchers with the design and the explication of the design of their research, thereby enhancing the credibility of their projects and enabling their research to establish well-founded and meaningful conclusions.

  13. Design and performance of an integrated ground and space sensor web for monitoring active volcanoes.

    Science.gov (United States)

    Lahusen, Richard; Song, Wenzhan; Kedar, Sharon; Shirazi, Behrooz; Chien, Steve; Doubleday, Joshua; Davies, Ashley; Webb, Frank; Dzurisin, Dan; Pallister, John

    2010-05-01

    An interdisciplinary team of computer, earth and space scientists collaborated to develop a sensor web system for rapid deployment at active volcanoes. The primary goals of this Optimized Autonomous Space In situ Sensorweb (OASIS) are to: 1) integrate complementary space and in situ (ground-based) elements into an interactive, autonomous sensor web; 2) advance sensor web power and communication resource management technology; and 3) enable scalability for seamless addition sensors and other satellites into the sensor web. This three-year project began with a rigorous multidisciplinary interchange that resulted in definition of system requirements to guide the design of the OASIS network and to achieve the stated project goals. Based on those guidelines, we have developed fully self-contained in situ nodes that integrate GPS, seismic, infrasonic and lightning (ash) detection sensors. The nodes in the wireless sensor network are linked to the ground control center through a mesh network that is highly optimized for remote geophysical monitoring. OASIS also features an autonomous bidirectional interaction between ground nodes and instruments on the EO-1 space platform through continuous analysis and messaging capabilities at the command and control center. Data from both the in situ sensors and satellite-borne hyperspectral imaging sensors stream into a common database for real-time visualization and analysis by earth scientists. We have successfully completed a field deployment of 15 nodes within the crater and on the flanks of Mount St. Helens, Washington. The demonstration that sensor web technology facilitates rapid network deployments and that we can achieve real-time continuous data acquisition. We are now optimizing component performance and improving user interaction for additional deployments at erupting volcanoes in 2010.

  14. Multidisciplinary care of craniosynostosis

    Directory of Open Access Journals (Sweden)

    Buchanan EP

    2017-07-01

    Full Text Available Edward P Buchanan,1 Yunfeng Xue,1 Amy S Xue,1 Asaf Olshinka,1 Sandi Lam2 1Michael E. DeBakey Department of Surgery, Division of Plastic Surgery, 2Michael E. DeBakey Department of Surgery, Division of Neurosurgery, Baylor College of Medicine, Houston, TX, USA Abstract: The management of craniosynostosis, especially in the setting of craniofacial syndromes, is ideally done in a multidisciplinary clinic with a team focused toward comprehensive care. Craniosynostosis is a congenital disorder of the cranium, caused by the premature fusion of one or more cranial sutures. This fusion results in abnormal cranial growth due to the inability of the involved sutures to accommodate the growing brain. Skull growth occurs only at the patent sutures, resulting in an abnormal head shape. If cranial growth is severely restricted, as seen in multisuture craniosynostosis, elevation in intracranial pressure can occur. Whereas most patients treated in a multidisciplinary craniofacial clinic have non-syndromic or isolated craniosynostosis, the most challenging patients are those with syndromic craniosynostosis. The purpose of this article was to discuss the multidisciplinary team care required to treat both syndromic and non-syndromic craniosynostosis. Keywords: multidisciplinary team care, syndromic craniosynostosis, nonsyndromic craniosynostosis

  15. Multidisciplinary team functioning.

    Science.gov (United States)

    Kovitz, K E; Dougan, P; Riese, R; Brummitt, J R

    1984-01-01

    This paper advocates the need to move beyond interdisciplinary team composition as a minimum criterion for multidisciplinary functioning in child abuse treatment. Recent developments within the field reflect the practice of shared professional responsibility for detection, case management and treatment. Adherence to this particular model for intervention requires cooperative service planning and implementation as task related functions. Implicitly, this model also carries the potential to incorporate the supportive functioning essential to effective group process. However, explicit attention to the dynamics and process of small groups has been neglected in prescriptive accounts of multidisciplinary child abuse team organization. The present paper therefore focuses upon the maintenance and enhancement aspects of multidisciplinary group functioning. First, the development and philosophy of service for the Alberta Children's Hospital Child Abuse Program are reviewed. Second, composition of the team, it's mandate for service, and the population it serves are briefly described. Third, the conceptual framework within which the program functions is outlined. Strategies for effective group functioning are presented and the difficulties encountered with this model are highlighted. Finally, recommendations are offered for planning and implementing a multidisciplinary child abuse team and for maintaining its effective group functioning.

  16. Designing neutral-atom nanotraps with integrated optical waveguides

    International Nuclear Information System (INIS)

    Burke, James P. Jr.; Chu, S.-T.; Bryant, Garnett W.; Williams, C.J.; Julienne, P.S.

    2002-01-01

    Integrated optical structures offer the intriguing potential of compact, reproducible waveguide arrays, rings, Y junctions, etc., that could be used to design evanescent field traps to transport, store, and interact atoms in networks as complicated as any integrated optical waveguide circuit. We theoretically investigate three approaches to trapping atoms above linear integrated optical waveguides. A two-color scheme balances the decaying evanescent fields of red- and blue-detuned light to produce a potential minimum above the guide. A one-color surface trap proposal uses blue-detuned light and the attractive surface interaction to provide a potential minimum. A third proposal uses blue-detuned light in two guides positioned above and below one another. The atoms are confined to the 'dark' spot in the vacuum gap between the guides. We find that all three approaches can be used to trap atoms in two or three dimensions with approximately 100 mW of laser power. We show that the dark spot guide is robust to light scatter and provides the most viable approach for constructing integrated optical circuits that could be used to transport and manipulate atoms in a controlled manner

  17. Design automation for integrated nonlinear logic circuits (Conference Presentation)

    Science.gov (United States)

    Van Vaerenbergh, Thomas; Pelc, Jason; Santori, Charles; Bose, Ranojoy; Kielpinski, Dave; Beausoleil, Raymond G.

    2016-05-01

    A key enabler of the IT revolution of the late 20th century was the development of electronic design automation (EDA) tools allowing engineers to manage the complexity of electronic circuits with transistor counts now reaching into the billions. Recently, we have been developing large-scale nonlinear photonic integrated logic circuits for next generation all-optical information processing. At this time a sufficiently powerful EDA-style software tool chain to design this type of complex circuits does not yet exist. Here we describe a hierarchical approach to automating the design and validation of photonic integrated circuits, which can scale to several orders of magnitude higher complexity than the state of the art. Most photonic integrated circuits developed today consist of a small number of components, and only limited hierarchy. For example, a simple photonic transceiver may contain on the order of 10 building-block components, consisting of grating couplers for photonic I/O, modulators, and signal splitters/combiners. Because this is relatively easy to lay out by hand (or simple script) existing photonic design tools have relatively little automation in comparison to electronics tools. But demonstrating all-optical logic will require significantly more complex photonic circuits containing up to 1,000 components, hence becoming infeasible to design manually. Our design framework is based off Python-based software from Luceda Photonics which provides an environment to describe components, simulate their behavior, and export design files (GDS) to foundries for fabrication. At a fundamental level, a photonic component is described as a parametric cell (PCell) similarly to electronics design. PCells are described by geometric characteristics of their layout. A critical part of the design framework is the implementation of PCells as Python objects. PCell objects can then use inheritance to simplify design, and hierarchical designs can be made by creating composite

  18. Design and Integration of Wearable Devices in Textiles

    Directory of Open Access Journals (Sweden)

    Isabel G. TRINDADE

    2014-12-01

    Full Text Available In this article, the design, production method, integration and characterization of textile sensors for the continuous monitoring of cardiac and respiration vital signals are presented. Textile electrodes, capacitive and piezoresistive sensors and respective interconnect plate were developed and integrated in elastic and adjustable chest bands, using a 6-needle digital embroidery machine and electrically conductive commercial threads. The signal's waveforms were recorded via PC with a data acquisition module and a LabView program. The signal to noise ratio of textile electrodes, having distinctive surface morphologies, that were either textured or smooth accordingly with the embroidery pattern used, were analyzed with Matlab. The quantitative method indicated differences between the two types of textile electrodes but performances comparable to standard Ag/AgCl gel electrodes. The sensors and interconnect plate were fully realized with the embroidery stitching method with textile fabrics and threads, and have a compact design, are lightweight and washable. The method offers great versatility for custom demand, in terms of sensor design and materials.

  19. Integrated heat exchanger design for a cryogenic storage tank

    Energy Technology Data Exchange (ETDEWEB)

    Fesmire, J. E.; Bonner, T.; Oliveira, J. M.; Johnson, W. L.; Notardonato, W. U. [NASA Kennedy Space Center, Cryogenics Test Laboratory, NE-F6, KSC, FL 32899 (United States); Tomsik, T. M. [NASA Glenn Research Center, 21000 Brookpark Road, Cleveland, OH 44135 (United States); Conyers, H. J. [NASA Stennis Space Center, Building 3225, SSC, MS 39529 (United States)

    2014-01-29

    Field demonstrations of liquid hydrogen technology will be undertaken for the proliferation of advanced methods and applications in the use of cryofuels. Advancements in the use of cryofuels for transportation on Earth, from Earth, or in space are envisioned for automobiles, aircraft, rockets, and spacecraft. These advancements rely on practical ways of storage, transfer, and handling of liquid hydrogen. Focusing on storage, an integrated heat exchanger system has been designed for incorporation with an existing storage tank and a reverse Brayton cycle helium refrigerator of capacity 850 watts at 20 K. The storage tank is a 125,000-liter capacity horizontal cylindrical tank, with vacuum jacket and multilayer insulation, and a small 0.6-meter diameter manway opening. Addressed are the specific design challenges associated with the small opening, complete modularity, pressure systems re-certification for lower temperature and pressure service associated with hydrogen densification, and a large 8:1 length-to-diameter ratio for distribution of the cryogenic refrigeration. The approach, problem solving, and system design and analysis for integrated heat exchanger are detailed and discussed. Implications for future space launch facilities are also identified. The objective of the field demonstration will be to test various zero-loss and densified cryofuel handling concepts for future transportation applications.

  20. Design and Fabrication of Vertically-Integrated CMOS Image Sensors

    Science.gov (United States)

    Skorka, Orit; Joseph, Dileepan

    2011-01-01

    Technologies to fabricate integrated circuits (IC) with 3D structures are an emerging trend in IC design. They are based on vertical stacking of active components to form heterogeneous microsystems. Electronic image sensors will benefit from these technologies because they allow increased pixel-level data processing and device optimization. This paper covers general principles in the design of vertically-integrated (VI) CMOS image sensors that are fabricated by flip-chip bonding. These sensors are composed of a CMOS die and a photodetector die. As a specific example, the paper presents a VI-CMOS image sensor that was designed at the University of Alberta, and fabricated with the help of CMC Microsystems and Micralyne Inc. To realize prototypes, CMOS dies with logarithmic active pixels were prepared in a commercial process, and photodetector dies with metal-semiconductor-metal devices were prepared in a custom process using hydrogenated amorphous silicon. The paper also describes a digital camera that was developed to test the prototype. In this camera, scenes captured by the image sensor are read using an FPGA board, and sent in real time to a PC over USB for data processing and display. Experimental results show that the VI-CMOS prototype has a higher dynamic range and a lower dark limit than conventional electronic image sensors. PMID:22163860