WorldWideScience

Sample records for integrated methodology trim

  1. Active Trimming of Hybrid Integrated Circuits

    OpenAIRE

    Németh, P.; Krémer, P.

    1984-01-01

    One of the more important fields of the microelectronics industry is the manufacturing of hybrid integrated circuits.An important part of the manufacturing process is concerned with the trimming of the hybrid integratedl circuits. This article deals with the basic principles of active trimming and introduces a microprocessor controlled trimming machine. By comparing active trimming with passive techniques, it can be shown that the active system has some advantages. This article outlines these...

  2. Trim cut machining and surface integrity analysis of Nimonic 80A alloy using wire cut EDM

    Directory of Open Access Journals (Sweden)

    Amitesh Goswami

    2017-02-01

    Full Text Available This present work deals with the features of trim cut wire EDM machining of Nimonic 80A in terms of machining parameters, to predict material removal rate (MRR, surface roughness (Ra, wire wear ratio (WWR and microstructure analysis. Trim cut is performed after rough cut to remove the rough layer deposited after machining due to melting and re-solidification of the eroded metal from workpiece as well as from wire electrode. Taguchi’s design of experiments methodology has been used for planning and designing the experiments. The relative significance of various factors has also been evaluated and analyzed using ANOVA. The results clearly indicate trim cut potential for high surface finish compared to rough cut machining.

  3. A fully integrated 16 channel digitally trimmed pulse shaping amplifier

    International Nuclear Information System (INIS)

    Hearn, W.E.; Wright, M.E.

    1993-11-01

    A fully integrated CMOS pulse shaping amplifier has been developed at LBL. All frequency dependent networks are included on the chip. Provision is made for tuning to compensate for process variations. The overall architecture and details of the circuitry are discussed. Test results are presented

  4. EVALUATION OF THE GRAI INTEGRATED METHODOLOGY AND THE IMAGIM SUPPORTWARE

    Directory of Open Access Journals (Sweden)

    J.M.C. Reid

    2012-01-01

    Full Text Available This paper describes the GRAI Integrated Methodology and identifies the need for computer tools to support enterprise modelling,design and integration. The IMAGIM tool is then evaluated in terms of its ability to support the GRAI Integrated Methodology. The GRAI Integrated Methodology is an Enterprise Integration methodology developed to support the design of CIM systems . The GRAI Integrated Methodology consists of the GRAI model and a structured approach. The latest addition to the methodology is the IMAGIM software tool developed by the GRAI research group for the specific purpose of supporting the methodology.

  5. Integrated Management System - Scope, Possibilities And Methodology

    Science.gov (United States)

    Čekanová, Katarína

    2015-06-01

    Organizations are becoming more aware of the importance of integrated management systems (IMS). Interest in this subject indicates that IMS are seen as "management systems of the future". Based on this, the aim of this articles characterizes the possibility of building IMS through the identification of common elements and specific requirements in accordance with the ISO 9001, ISO 14001 and OHSAS 18001 professional references. Part of the article is the methodology of building IMS in the organization.

  6. NCSX Trim Coil Design

    International Nuclear Information System (INIS)

    Kalish, M.; Brooks, A.; Rushinski, J.; Upcavage, R.

    2009-01-01

    The National Compact Stellarator Experiment (NCSX) was being constructed at the Princeton Plasma Physics Laboratory in partnership with Oak Ridge National Laboratory before work was stopped in 2008. The objective of this experiment was to develop the stellarator concept and evaluate it's potential as a model for future fusion power plants. Stellarator design requires very precisely positioned Modular Coils of complex shape to form 3D plasmas. In the design of NCSX, Trim Coils were required to compensate for both the positioning of the coils during assembly and the fabrication tolerances of the Modular Coils. Use of the Trim Coils allowed for larger tolerances increasing ease of assembly and decreasing overall cost. A set of Trim coils was developed to suppress the toroidal flux in island regions due to misalignment, magnetic materials, and eddy currents. The requirement imposed upon the design forced the toroidal flux in island regions below 10% of the total toroidal flux in the plasma. An analysis was first performed to evaluate candidate Trim Coil configurations iterating both the size, number, and position of the coils. The design was optimized considering both performance and cost while staying within the tight restraints presented by the space limited geometry. The final design of the Trim Coils incorporated a 48 Coil top bottom symmetric set. Fabrication costs were minimized by having only two coil types and using a planar conventional design with off the shelf commercial conductor. The Trim Coil design incorporated supports made from simple structural shapes assembled together in a way which allowed for adjustment as well as accommodation for the tolerance build up on the mating surfaces. This paper will summarize the analysis that led to the optimization of the Trim Coils set, the trim coil mechanical design, thermal and stress analysis, and the design of the supporting Trim Coil structure

  7. Methodology, Algorithms, and Emerging Tool for Automated Design of Intelligent Integrated Multi-Sensor Systems

    Directory of Open Access Journals (Sweden)

    Andreas König

    2009-11-01

    Full Text Available The emergence of novel sensing elements, computing nodes, wireless communication and integration technology provides unprecedented possibilities for the design and application of intelligent systems. Each new application system must be designed from scratch, employing sophisticated methods ranging from conventional signal processing to computational intelligence. Currently, a significant part of this overall algorithmic chain of the computational system model still has to be assembled manually by experienced designers in a time and labor consuming process. In this research work, this challenge is picked up and a methodology and algorithms for automated design of intelligent integrated and resource-aware multi-sensor systems employing multi-objective evolutionary computation are introduced. The proposed methodology tackles the challenge of rapid-prototyping of such systems under realization constraints and, additionally, includes features of system instance specific self-correction for sustained operation of a large volume and in a dynamically changing environment. The extension of these concepts to the reconfigurable hardware platform renders so called self-x sensor systems, which stands, e.g., for self-monitoring, -calibrating, -trimming, and -repairing/-healing systems. Selected experimental results prove the applicability and effectiveness of our proposed methodology and emerging tool. By our approach, competitive results were achieved with regard to classification accuracy, flexibility, and design speed under additional design constraints.

  8. A Methodology for Integrating Maintainability Using Software Metrics

    OpenAIRE

    Lewis, John A.; Henry, Sallie M.

    1989-01-01

    Maintainability must be integrated into software early in the development process. But for practical use, the techniques used must be as unobtrusive to the existing software development process as possible. This paper defines a methodology for integrating maintainability into large-scale software and describes an experiment which implemented the methodology into a major commercial software development environment.

  9. Trim coil power supplies

    International Nuclear Information System (INIS)

    Haisler, R.; Peeler, H.; Zajicek, W.

    1985-01-01

    The 18 trim coil power supplies have been constructed and are now in place in the K500 pit and pit mezzanine. Final wiring of the primary power and control power is proceeding along with installation of cooling water supplies. The supplies are expected to be ready for final testing into resistive loads at the beginning of June, 1985

  10. Development Methodology for an Integrated Legal Cadastre

    NARCIS (Netherlands)

    Hespanha, J.P.

    2012-01-01

    This Thesis describes the research process followed in order to achieve a development methodology applicable to the reform of cadastral systems with a legal basis. It was motivated by the author’s participation in one of the first surveying and mapping operations for a digital cadastre in Portugal,

  11. [Quality and integrity in the production and publication of scientific results: data trimming, manipulation and (self) plagiarism].

    Science.gov (United States)

    Lüscher, T F

    2014-08-01

    The publication of scientific manuscripts is an essential part in the research process and in the attempt to produce novel knowledge: only what is published exists. It is the aim of research to produce reproducible and sustainable knowledge. Reproducible knowledge is based on precise observation, the use of modern methodologies and an appropriate statistical analysis. As a consequence, it must be the intention of any scientist to report the truth and nothing but the truth. This principle requires precision and honesty. Deviation from such a behavior may lead to scientific misconduct: It encompasses the use of inappropriate methods and/or statistics, double publication of data, sloppy data presentation and processing, up to data massaging, manipulation, data theft or fabrication. Famous examples can be found throughout the history of research but it appears that such behavior has recently become more common possibly due to excessive competition, the crucial role of grants for scientific productivity and funding as well as promotion. Accordingly, in the training of researchers it seems essential to emphasize the importance of precise data acquisition and analysis to ascertain reproducible data. Similarly, it must be assured that data sets are only published once, that authors have contributed technically and/or intellectually in an important manner and that the work of other scientists is cited appropriately. Editors and reviewers should carefully assess the quality of submitted manuscripts. In fact, it is the aim of the peer review process to assure as much as possible that the quality of submitted manuscripts meets current methodological as well as ethical standards.

  12. Integrated Deterministic-Probabilistic Safety Assessment Methodologies

    Energy Technology Data Exchange (ETDEWEB)

    Kudinov, P.; Vorobyev, Y.; Sanchez-Perea, M.; Queral, C.; Jimenez Varas, G.; Rebollo, M. J.; Mena, L.; Gomez-Magin, J.

    2014-02-01

    IDPSA (Integrated Deterministic-Probabilistic Safety Assessment) is a family of methods which use tightly coupled probabilistic and deterministic approaches to address respective sources of uncertainties, enabling Risk informed decision making in a consistent manner. The starting point of the IDPSA framework is that safety justification must be based on the coupling of deterministic (consequences) and probabilistic (frequency) considerations to address the mutual interactions between stochastic disturbances (e.g. failures of the equipment, human actions, stochastic physical phenomena) and deterministic response of the plant (i.e. transients). This paper gives a general overview of some IDPSA methods as well as some possible applications to PWR safety analyses. (Author)

  13. A Quality-Driven Methodology for Information Systems Integration

    Directory of Open Access Journals (Sweden)

    Iyad Zikra

    2017-10-01

    Full Text Available Information systems integration is an essential instrument for organizations to attain advantage in today’s growing and fast changing business and technology landscapes. Integration solutions generate added value by combining the functionality and services of heterogeneous and diverse systems. Existing integration environments tend to rely heavily on technical, platform-dependent skills. Consequently, the solutions that they enable are not optimally aligned with the envisioned business goals of the organization. Furthermore, the gap between the goals and the solutions complicates the task of evaluating the quality of integration solutions. To address these challenges, we propose a quality-driven, model-driven methodology for designing and developing integration solutions. The methodology spans organizational and systems design details, providing a holistic view of the integration solution and its underlying business goals. A multi-view meta-model provides the basis for the integration design. Quality factors that affect various aspects of the integration solution guide and inform the progress of the methodology. An example business case is presented to demonstrate the application of the methodology.

  14. METHODOLOGY FRAMEWORK FOR PROCESS INTEGRATION AND SERVICE MANAGEMENT

    Directory of Open Access Journals (Sweden)

    Darko Galinec

    2007-06-01

    Full Text Available History of information systems development was driven by business system's functions automation and mergers and acquisitions - business subjects integration into a whole. Modern business requires business processes integration through their dynamics and thus enterprise application integration (EAI as well. In this connection it is necessary to find ways and means of application integration and interaction in a consistent and reliable way. The real-time enterprise (RTE monitors, captures and analyzes root causes and overt events that are critical to its success the instant those events occur [6]. EAI is determined by business needs and business requirements. It must be based on business process repository and models, business integration methodology (BIM and information flow as well. Decisions concerning technology must be in function of successful application integration. In this paper EAI methodological framework and technological concepts for its achievements are introduced.

  15. Integration of infrared thermography into various maintenance methodologies

    Science.gov (United States)

    Morgan, William T.

    1993-04-01

    Maintenance methodologies are in developmental stages throughout the world as global competitiveness drives all industries to improve operational efficiencies. Rapid progress in technical advancements has added an additional strain on maintenance organizations to progressively change. Accompanying needs for advanced training and documentation is the demand for utilization of various analytical instruments and quantitative methods. Infrared thermography is one of the primary elements of engineered approaches to maintenance. Current maintenance methodologies can be divided into six categories; Routine ('Breakdown'), Preventive, Predictive, Proactive, Reliability-Based, and Total Productive (TPM) maintenance. Each of these methodologies have distinctive approaches to achieving improved operational efficiencies. Popular though is that infrared thermography is a Predictive maintenance tool. While this is true, it is also true that it can be effectively integrated into each of the maintenance methodologies for achieving desired results. The six maintenance strategies will be defined. Infrared applications integrated into each will be composed in tabular form.

  16. Methodology and integrated studies for the strategic regional uranium prospects

    International Nuclear Information System (INIS)

    Andrade Tolentino, J. de.

    1984-01-01

    An integrated methodology alternative to the traditional one used for uranium prospecting is presented. For this purpose a detailed revision of some methods for finding uranium was made. Then a geological unit located in Minas Gerais, Brazil, was chosen due to its geographical proximity to the Lagoa Real deposit in the Brazilian Bahia State. The methodology applied to this unit gave a preliminary indications of areas to be prospected in detail. 36 refs, 44 figs, 20 tabs

  17. Environmental impact assessment for energy pathways: an integrated methodology

    International Nuclear Information System (INIS)

    Sommereux-Blanc, Isabelle

    2010-01-01

    This document presents the synthesis of my research work contributing to the development of an integrated methodology of environmental impact assessment for energy pathways. In the context of world globalization, environmental impact assessments issues are highly linked with the following questioning: Which environmental impacts? for which demand? at which location? at which temporal scale? My work is built upon the definition of a conceptual framework able to handle these issues and upon its progressive implementation. The integration of the spatial and temporal issues within the methodology are key elements. Fundamental cornerstones of this framework are presented along the DPSIR concept (Driving forces, Pressures, State, Impacts, Responses). They cover a comprehensive analysis of the limits and the relevance of life cycle analysis and the development of a geo-spatialized environmental performance approach for an electrical production pathway. Perspectives linked with the development of this integrated methodology are detailed for energy pathways. (author)

  18. An Integrated Safety Assessment Methodology for Generation IV Nuclear Systems

    International Nuclear Information System (INIS)

    Leahy, Timothy J.

    2010-01-01

    The Generation IV International Forum (GIF) Risk and Safety Working Group (RSWG) was created to develop an effective approach for the safety of Generation IV advanced nuclear energy systems. Early work of the RSWG focused on defining a safety philosophy founded on lessons learned from current and prior generations of nuclear technologies, and on identifying technology characteristics that may help achieve Generation IV safety goals. More recent RSWG work has focused on the definition of an integrated safety assessment methodology for evaluating the safety of Generation IV systems. The methodology, tentatively called ISAM, is an integrated 'toolkit' consisting of analytical techniques that are available and matched to appropriate stages of Generation IV system concept development. The integrated methodology is intended to yield safety-related insights that help actively drive the evolving design throughout the technology development cycle, potentially resulting in enhanced safety, reduced costs, and shortened development time.

  19. Networks as integrated in research methodologies in PER

    DEFF Research Database (Denmark)

    Bruun, Jesper

    2016-01-01

    of using networks to create insightful maps of learning discussions. To conclude, I argue that conceptual blending is a powerful framework for constructing "mixed methods" methodologies that may integrate diverse theories and other methodologies with network methodologies.......In recent years a number of researchers within the PER community have started using network analysis as a new methodology to extend our understanding of teaching and learning physics by viewing these as complex systems. In this paper, I give examples of social, cognitive, and action mapping...... networks and how they can be analyzed. In so doing I show how a network can be methodologically described as a set of relations between a set of entities, and how a network can be characterized and analyzed as a mathematical object. Then, as an illustrative example, I discuss a relatively new example...

  20. A 3D Hybrid Integration Methodology for Terabit Transceivers

    DEFF Research Database (Denmark)

    Dong, Yunfeng; Johansen, Tom Keinicke; Zhurbenko, Vitaliy

    2015-01-01

    integration are described. An equivalent circuit model of the via-throughs connecting the RF circuitry to the modulator is proposed and its lumped element parameters are extracted. Wire bonding transitions between the driving and RF circuitry were designed and simulated. An optimized 3D interposer design......This paper presents a three-dimensional (3D) hybrid integration methodology for terabit transceivers. The simulation methodology for multi-conductor structures are explained. The effect of ground vias on the RF circuitry and the preferred interposer substrate material for large bandwidth 3D hybrid...

  1. Integrated structure/control design - Present methodology and future opportunities

    Science.gov (United States)

    Weisshaar, T. A.; Newsom, J. R.; Zeiler, T. A.; Gilbert, M. G.

    1986-01-01

    Attention is given to current methodology applied to the integration of the optimal design process for structures and controls. Multilevel linear decomposition techniques proved to be most effective in organizing the computational efforts necessary for ISCD (integrated structures and control design) tasks. With the development of large orbiting space structures and actively controlled, high performance aircraft, there will be more situations in which this concept can be applied.

  2. Qualitative case study methodology in nursing research: an integrative review.

    Science.gov (United States)

    Anthony, Susan; Jack, Susan

    2009-06-01

    This paper is a report of an integrative review conducted to critically analyse the contemporary use of qualitative case study methodology in nursing research. Increasing complexity in health care and increasing use of case study in nursing research support the need for current examination of this methodology. In 2007, a search for case study research (published 2005-2007) indexed in the CINAHL, MEDLINE, EMBASE, PsychINFO, Sociological Abstracts and SCOPUS databases was conducted. A sample of 42 case study research papers met the inclusion criteria. Whittemore and Knafl's integrative review method guided the analysis. Confusion exists about the name, nature and use of case study. This methodology, including terminology and concepts, is often invisible in qualitative study titles and abstracts. Case study is an exclusive methodology and an adjunct to exploring particular aspects of phenomena under investigation in larger or mixed-methods studies. A high quality of case study exists in nursing research. Judicious selection and diligent application of literature review methods promote the development of nursing science. Case study is becoming entrenched in the nursing research lexicon as a well-accepted methodology for studying phenomena in health and social care, and its growing use warrants continued appraisal to promote nursing knowledge development. Attention to all case study elements, process and publication is important in promoting authenticity, methodological quality and visibility.

  3. AN INTEGRATED METHODOLOGY FOR CUSTOMER RELATIONSHIP MANAGEMENT CUSTOMIZATION

    Directory of Open Access Journals (Sweden)

    Ricardo Colomo Palacios

    2008-02-01

    Full Text Available The importance and presence of technological solutions in organizations supporting CRM are a vital business fact from the late nineties. Presently, the manufacturers figure in the market has dramatically decreased because of continuous takeovers and merges, but it has on the other hand gained momentum because of the sudden open-source and on-demand solutions appearance. In this scope, a unified methodology centered on CRM solutions is of paramount importance since it has traditionally been linked to either system integration or overall solution design. Based on the two de-facto complementary standards for the implementation and development of Information Systems, namely the ESA and Dyché CRM systems implementation methodology, in this paper, we provide a CRM business solutions customization methodology which pertains independently to the integration and tool maker perspective.

  4. Integral Methodological Pluralism in Science Education Research: Valuing Multiple Perspectives

    Science.gov (United States)

    Davis, Nancy T.; Callihan, Laurie P.

    2013-01-01

    This article examines the multiple methodologies used in educational research and proposes a model that includes all of them as contributing to understanding educational contexts and research from multiple perspectives. The model, based on integral theory (Wilber in a theory of everything. Shambhala, Boston, 2000) values all forms of research as…

  5. Integrating Shamanic Methodology into the Spirituality of Addictions Recovery Work

    Science.gov (United States)

    Rich, Marcia L.

    2012-01-01

    Responding to an increased recognition of the importance of spirituality in the aetiology and treatment of addictions, this article provides an overview of the potential contributions of both transpersonal psychology and shamanic methodology for the addictions field. A case study is provided to illustrate the integration of conventional,…

  6. Effects of varying laser trimming geometries on thin film\\ud resistors

    OpenAIRE

    Alafogianni, Maria; Birkett, Martin; Penlington, Roger

    2017-01-01

    Purpose - This paper studies the effects of varying laser trim patterns on several performance parameters of thin film resistors such as the temperature coefficient of resistance (TCR) and target resistance value.\\ud \\ud Design/methodology/approach - The benefits and limitations of basic trim patterns are taken into consideration and the plunge cut, double plunge cut and the curved L-cut were selected to be modelled and tested experimentally. A computer simulation of the laser trim patterns h...

  7. Application of integrated fuzzy VIKOR & AHP methodology to contractor ranking

    Directory of Open Access Journals (Sweden)

    Mohamad Rahim Ramezaniyan

    2012-08-01

    Full Text Available Contractor selection is a critical activity, which plays an important role in the overall success of any construction project. The implementation of fuzzy multiple criteria decision attribute (MCDA in selecting contractors has the advantage of rendering subjective and implicit decision making more objective and transparent. An additional merit of fuzzy MCDA is the ability to accommodate quantitative and qualitative information. In this paper, an integrated VIKOR–AHP methodology is proposed to make a selection among the alternative contractors in one of Iranian construction industry projects. In the proposed methodology, the weights of the selection criteria are determined by fuzzy pairwise comparison matrices of AHP.

  8. An Introduction To PC-TRIM.

    Science.gov (United States)

    John R. Mills

    1989-01-01

    The timber resource inventory model (TRIM) has been adapted to run on person al computers. The personal computer version of TRIM (PC-TRIM) is more widely used than its mainframe parent. Errors that existed in previous versions of TRIM have been corrected. Information is presented to help users with program input and output management in the DOS environment, to...

  9. Methodology for dimensional variation analysis of ITER integrated systems

    International Nuclear Information System (INIS)

    Fuentes, F. Javier; Trouvé, Vincent; Cordier, Jean-Jacques; Reich, Jens

    2016-01-01

    Highlights: • Tokamak dimensional management methodology, based on 3D variation analysis, is presented. • Dimensional Variation Model implementation workflow is described. • Methodology phases are described in detail. The application of this methodology to the tolerance analysis of ITER Vacuum Vessel is presented. • Dimensional studies are a valuable tool for the assessment of Tokamak PCR (Project Change Requests), DR (Deviation Requests) and NCR (Non-Conformance Reports). - Abstract: The ITER machine consists of a large number of complex systems highly integrated, with critical functional requirements and reduced design clearances to minimize the impact in cost and performances. Tolerances and assembly accuracies in critical areas could have a serious impact in the final performances, compromising the machine assembly and plasma operation. The management of tolerances allocated to part manufacture and assembly processes, as well as the control of potential deviations and early mitigation of non-compliances with the technical requirements, is a critical activity on the project life cycle. A 3D tolerance simulation analysis of ITER Tokamak machine has been developed based on 3DCS dedicated software. This integrated dimensional variation model is representative of Tokamak manufacturing functional tolerances and assembly processes, predicting accurate values for the amount of variation on critical areas. This paper describes the detailed methodology to implement and update the Tokamak Dimensional Variation Model. The model is managed at system level. The methodology phases are illustrated by its application to the Vacuum Vessel (VV), considering the status of maturity of VV dimensional variation model. The following topics are described in this paper: • Model description and constraints. • Model implementation workflow. • Management of input and output data. • Statistical analysis and risk assessment. The management of the integration studies based on

  10. Methodology for dimensional variation analysis of ITER integrated systems

    Energy Technology Data Exchange (ETDEWEB)

    Fuentes, F. Javier, E-mail: FranciscoJavier.Fuentes@iter.org [ITER Organization, Route de Vinon-sur-Verdon—CS 90046, 13067 St Paul-lez-Durance (France); Trouvé, Vincent [Assystem Engineering & Operation Services, rue J-M Jacquard CS 60117, 84120 Pertuis (France); Cordier, Jean-Jacques; Reich, Jens [ITER Organization, Route de Vinon-sur-Verdon—CS 90046, 13067 St Paul-lez-Durance (France)

    2016-11-01

    Highlights: • Tokamak dimensional management methodology, based on 3D variation analysis, is presented. • Dimensional Variation Model implementation workflow is described. • Methodology phases are described in detail. The application of this methodology to the tolerance analysis of ITER Vacuum Vessel is presented. • Dimensional studies are a valuable tool for the assessment of Tokamak PCR (Project Change Requests), DR (Deviation Requests) and NCR (Non-Conformance Reports). - Abstract: The ITER machine consists of a large number of complex systems highly integrated, with critical functional requirements and reduced design clearances to minimize the impact in cost and performances. Tolerances and assembly accuracies in critical areas could have a serious impact in the final performances, compromising the machine assembly and plasma operation. The management of tolerances allocated to part manufacture and assembly processes, as well as the control of potential deviations and early mitigation of non-compliances with the technical requirements, is a critical activity on the project life cycle. A 3D tolerance simulation analysis of ITER Tokamak machine has been developed based on 3DCS dedicated software. This integrated dimensional variation model is representative of Tokamak manufacturing functional tolerances and assembly processes, predicting accurate values for the amount of variation on critical areas. This paper describes the detailed methodology to implement and update the Tokamak Dimensional Variation Model. The model is managed at system level. The methodology phases are illustrated by its application to the Vacuum Vessel (VV), considering the status of maturity of VV dimensional variation model. The following topics are described in this paper: • Model description and constraints. • Model implementation workflow. • Management of input and output data. • Statistical analysis and risk assessment. The management of the integration studies based on

  11. An Integrated Methodology for Emulsified Formulated Product Design

    DEFF Research Database (Denmark)

    Mattei, Michele

    are mixed together to determine the desired emulsified product. They are still mainly designed and analysed through trial - and - error based exper- imental techniques, therefore a systematic approach , integrating model-based as well a s experiment - based techniques, for design of these products could......The consumer oriented chemical based products are used every day by millions of people. They are structured products constituted of numerous chemicals, and many of them, especially household and personal care products, are emulsions where active ingredients, solvents, additives and surfactants...... significantly reduce both time and cost connected to product development by doing only the necessary experi- ments , and ensuring chances for innovation . The main contribution of this project i s the development of an integrated methodology for the design of emulsified formulated products. The methodology...

  12. Integrated Management System – Scope, Possibilities And Methodology

    Directory of Open Access Journals (Sweden)

    Čekanová Katarína

    2015-06-01

    Full Text Available Organizations are becoming more aware of the importance of integrated management systems (IMS. Interest in this subject indicates that IMS are seen as “management systems of the future”. Based on this, the aim of this articles characterizes the possibility of building IMS through the identification of common elements and specific requirements in accordance with the ISO 9001, ISO 14001 and OHSAS 18001 professional references. Part of the article is the methodology of building IMS in the organization.

  13. Methodological Problems on the Way to Integrative Human Neuroscience

    Science.gov (United States)

    Kotchoubey, Boris; Tretter, Felix; Braun, Hans A.; Buchheim, Thomas; Draguhn, Andreas; Fuchs, Thomas; Hasler, Felix; Hastedt, Heiner; Hinterberger, Thilo; Northoff, Georg; Rentschler, Ingo; Schleim, Stephan; Sellmaier, Stephan; Tebartz Van Elst, Ludger; Tschacher, Wolfgang

    2016-01-01

    Neuroscience is a multidisciplinary effort to understand the structures and functions of the brain and brain-mind relations. This effort results in an increasing amount of data, generated by sophisticated technologies. However, these data enhance our descriptive knowledge, rather than improve our understanding of brain functions. This is caused by methodological gaps both within and between subdisciplines constituting neuroscience, and the atomistic approach that limits the study of macro- and mesoscopic issues. Whole-brain measurement technologies do not resolve these issues, but rather aggravate them by the complexity problem. The present article is devoted to methodological and epistemic problems that obstruct the development of human neuroscience. We neither discuss ontological questions (e.g., the nature of the mind) nor review data, except when it is necessary to demonstrate a methodological issue. As regards intradisciplinary methodological problems, we concentrate on those within neurobiology (e.g., the gap between electrical and chemical approaches to neurophysiological processes) and psychology (missing theoretical concepts). As regards interdisciplinary problems, we suggest that core disciplines of neuroscience can be integrated using systemic concepts that also entail human-environment relations. We emphasize the necessity of a meta-discussion that should entail a closer cooperation with philosophy as a discipline of systematic reflection. The atomistic reduction should be complemented by the explicit consideration of the embodiedness of the brain and the embeddedness of humans. The discussion is aimed at the development of an explicit methodology of integrative human neuroscience, which will not only link different fields and levels, but also help in understanding clinical phenomena. PMID:27965548

  14. Methodological Problems on the Way to Integrative Human Neuroscience.

    Science.gov (United States)

    Kotchoubey, Boris; Tretter, Felix; Braun, Hans A; Buchheim, Thomas; Draguhn, Andreas; Fuchs, Thomas; Hasler, Felix; Hastedt, Heiner; Hinterberger, Thilo; Northoff, Georg; Rentschler, Ingo; Schleim, Stephan; Sellmaier, Stephan; Tebartz Van Elst, Ludger; Tschacher, Wolfgang

    2016-01-01

    Neuroscience is a multidisciplinary effort to understand the structures and functions of the brain and brain-mind relations. This effort results in an increasing amount of data, generated by sophisticated technologies. However, these data enhance our descriptive knowledge , rather than improve our understanding of brain functions. This is caused by methodological gaps both within and between subdisciplines constituting neuroscience, and the atomistic approach that limits the study of macro- and mesoscopic issues. Whole-brain measurement technologies do not resolve these issues, but rather aggravate them by the complexity problem. The present article is devoted to methodological and epistemic problems that obstruct the development of human neuroscience. We neither discuss ontological questions (e.g., the nature of the mind) nor review data, except when it is necessary to demonstrate a methodological issue. As regards intradisciplinary methodological problems, we concentrate on those within neurobiology (e.g., the gap between electrical and chemical approaches to neurophysiological processes) and psychology (missing theoretical concepts). As regards interdisciplinary problems, we suggest that core disciplines of neuroscience can be integrated using systemic concepts that also entail human-environment relations. We emphasize the necessity of a meta-discussion that should entail a closer cooperation with philosophy as a discipline of systematic reflection. The atomistic reduction should be complemented by the explicit consideration of the embodiedness of the brain and the embeddedness of humans. The discussion is aimed at the development of an explicit methodology of integrative human neuroscience , which will not only link different fields and levels, but also help in understanding clinical phenomena.

  15. Integral Design Methodology of Photocatalytic Reactors for Air Pollution Remediation

    Directory of Open Access Journals (Sweden)

    Claudio Passalía

    2017-06-01

    Full Text Available An integral reactor design methodology was developed to address the optimal design of photocatalytic wall reactors to be used in air pollution control. For a target pollutant to be eliminated from an air stream, the proposed methodology is initiated with a mechanistic derived reaction rate. The determination of intrinsic kinetic parameters is associated with the use of a simple geometry laboratory scale reactor, operation under kinetic control and a uniform incident radiation flux, which allows computing the local superficial rate of photon absorption. Thus, a simple model can describe the mass balance and a solution may be obtained. The kinetic parameters may be estimated by the combination of the mathematical model and the experimental results. The validated intrinsic kinetics obtained may be directly used in the scaling-up of any reactor configuration and size. The bench scale reactor may require the use of complex computational software to obtain the fields of velocity, radiation absorption and species concentration. The complete methodology was successfully applied to the elimination of airborne formaldehyde. The kinetic parameters were determined in a flat plate reactor, whilst a bench scale corrugated wall reactor was used to illustrate the scaling-up methodology. In addition, an optimal folding angle of the corrugated reactor was found using computational fluid dynamics tools.

  16. THERP and HEART integrated methodology for human error assessment

    Science.gov (United States)

    Castiglia, Francesco; Giardina, Mariarosa; Tomarchio, Elio

    2015-11-01

    THERP and HEART integrated methodology is proposed to investigate accident scenarios that involve operator errors during high-dose-rate (HDR) treatments. The new approach has been modified on the basis of fuzzy set concept with the aim of prioritizing an exhaustive list of erroneous tasks that can lead to patient radiological overexposures. The results allow for the identification of human errors that are necessary to achieve a better understanding of health hazards in the radiotherapy treatment process, so that it can be properly monitored and appropriately managed.

  17. INTEGRATED METHODOLOGY FOR PRODUCT PLANNING USING MULTI CRITERIA ANALYSIS

    Directory of Open Access Journals (Sweden)

    Tarun Soota

    2016-09-01

    Full Text Available Integrated approach to multi-criteria decision problems is proposed using quality function deployment and analytical network process. The objective of the work is to rationalize and improve the method of analyzing and interpreting customer needs and technical requirements. The methodology is used to determine, prioritize engineering requirements based on customer needs for development of best product. Framework allows decision maker to decompose a complex problem in a hierarchical structure to show relationship between objective and criteria. Multi-criteria decision modeling is used for extending the hierarchy process to both dependence and feedback. A case study on bikes is presented for the proposed model.

  18. Statistical Methodologies to Integrate Experimental and Computational Research

    Science.gov (United States)

    Parker, P. A.; Johnson, R. T.; Montgomery, D. C.

    2008-01-01

    Development of advanced algorithms for simulating engine flow paths requires the integration of fundamental experiments with the validation of enhanced mathematical models. In this paper, we provide an overview of statistical methods to strategically and efficiently conduct experiments and computational model refinement. Moreover, the integration of experimental and computational research efforts is emphasized. With a statistical engineering perspective, scientific and engineering expertise is combined with statistical sciences to gain deeper insights into experimental phenomenon and code development performance; supporting the overall research objectives. The particular statistical methods discussed are design of experiments, response surface methodology, and uncertainty analysis and planning. Their application is illustrated with a coaxial free jet experiment and a turbulence model refinement investigation. Our goal is to provide an overview, focusing on concepts rather than practice, to demonstrate the benefits of using statistical methods in research and development, thereby encouraging their broader and more systematic application.

  19. Integrated Methodology for Estimating Water Use in Mediterranean Agricultural Areas

    Directory of Open Access Journals (Sweden)

    George C. Zalidis

    2009-08-01

    Full Text Available Agricultural use is by far the largest consumer of fresh water worldwide, especially in the Mediterranean, where it has reached unsustainable levels, thus posing a serious threat to water resources. Having a good estimate of the water used in an agricultural area would help water managers create incentives for water savings at the farmer and basin level, and meet the demands of the European Water Framework Directive. This work presents an integrated methodology for estimating water use in Mediterranean agricultural areas. It is based on well established methods of estimating the actual evapotranspiration through surface energy fluxes, customized for better performance under the Mediterranean conditions: small parcel sizes, detailed crop pattern, and lack of necessary data. The methodology has been tested and validated on the agricultural plain of the river Strimonas (Greece using a time series of Terra MODIS and Landsat 5 TM satellite images, and used to produce a seasonal water use map at a high spatial resolution. Finally, a tool has been designed to implement the methodology with a user-friendly interface, in order to facilitate its operational use.

  20. A case on vendor selection methodology: An integrated approach

    Directory of Open Access Journals (Sweden)

    Nikhil C. Shil

    2009-11-01

    Full Text Available Vendor selection methodology is a highly researched area in supply chain management l terature and a very significant decision taken by supply chain managers due to technological advances in the manufacturing process. Such research has two basic dimensions: one is related to the identification of variables affecting the performance of the vendors and the other deals with the methodology to be applied. Most of the research conducted in this area deal with the upfront selection of vendors. However, it is very common to have a list of dedicated vendors due to the development of sophisticated production technologies like just in time (JIT, a lean or agile manufacturing process where continuous flow of materials is a requirement. This paper addresses the issue of selecting the optimal vendor from the internal database of a company. Factor analysis, analytical hierarchy process and regression analysis is used in an integrated way to supplement the vendor selection process. The methodology presented here is simply a proposal where every possible room for adjustment is available.

  1. Integrating FMEA in a Model-Driven Methodology

    Science.gov (United States)

    Scippacercola, Fabio; Pietrantuono, Roberto; Russo, Stefano; Esper, Alexandre; Silva, Nuno

    2016-08-01

    Failure Mode and Effects Analysis (FMEA) is a well known technique for evaluating the effects of potential failures of components of a system. FMEA demands for engineering methods and tools able to support the time- consuming tasks of the analyst. We propose to make FMEA part of the design of a critical system, by integration into a model-driven methodology. We show how to conduct the analysis of failure modes, propagation and effects from SysML design models, by means of custom diagrams, which we name FMEA Diagrams. They offer an additional view of the system, tailored to FMEA goals. The enriched model can then be exploited to automatically generate FMEA worksheet and to conduct qualitative and quantitative analyses. We present a case study from a real-world project.

  2. Methodology for Selecting Best Management Practices Integrating Multiple Stakeholders and Criteria. Part 1: Methodology

    Directory of Open Access Journals (Sweden)

    Mauricio Carvallo Aceves

    2016-02-01

    Full Text Available The implementation of stormwater Best Management Practices (BMPs could help re-establish the natural hydrological cycle of watersheds after urbanization, with each BMP presenting a different performance across a range of criteria (flood prevention, pollutant removal, etc.. Additionally, conflicting views from the relevant stakeholders may arise, resulting in a complex selection process. This paper proposes a methodology for BMP selection based on the application of multi-criteria decision aid (MCDA methods, integrating multiple stakeholder priorities and BMP combinations. First, in the problem definition, the MCDA methods, relevant criteria and design guidelines are selected. Next, information from the preliminary analysis of the watershed is used to obtain a list of relevant BMPs. The third step comprises the watershed modeling and analysis of the BMP alternatives to obtain performance values across purely objective criteria. Afterwards, a stakeholder analysis based on survey applications is carried out to obtain social performance values and criteria priorities. Then, the MCDA methods are applied to obtain the final BMP rankings. The last step considers the sensitivity analysis and rank comparisons in order to draw the final conclusions and recommendations. Future improvements to the methodology could explore inclusion of multiple objective analysis, and alternative means for obtaining social performance values.

  3. Usefulness of alternative integrative assessment methodologies in public decision making

    Energy Technology Data Exchange (ETDEWEB)

    Erickson, L. E.; Litchfield, J. W.; Currie, J. W.; McDonald, C. L.; Adams, R. C.

    1978-07-01

    Many diverse social, economic, and environmental effects are associated with each of the available energy development alternatives. The assessment of the costs, risks, and benefits of these energy development options is an important function of the U. S. Department of Energy. This task is more difficult when no single alternative is better than the others in all respects. This paper compares benefit-cost and multi-attribute utility analysis as decision aids for these more difficult and more common assessment cases. PNL has developed expertise in making these assessments through its involvement since the Calvert Cliffs decision in both the preparation of Environmental Impact Statements and the development of methods to make these statements more thorough and responsive to the spirit of the National Environmental Protection Act (NEPA). Since 1973 PNL has had continuing efforts to quantify, value, and compare all of the major factors which influence the overall impacts of energy development options. An important part of this work has been the measurement and incorporation of the relative values which community groups place on these conflicting factors. Such difficult assessment problems could be approached in many ways including the use of benefit-cost or multi-attribute utility analysis. This paper addresses the following questions: (1) Should an integrative assessment methodology be used for the overall assessment of these costs, risks, and benefits. (2) If an integrative assessment methodology is to be used, what alternative methods are available and what should be the basis for selecting a method. (3) Is it possible to use one of the available alternatives for one portion of the assessment and another for another portion of the assessment. The answers to these questions presented in this report are applicable to most public decision problems.

  4. Trends in scenario development methodologies and integration in NUMO's approach

    International Nuclear Information System (INIS)

    Ebashi, Takeshi; Ishiguro, Katsuhiko; Wakasugi, Keiichiro; Kawamura, Hideki; Gaus, Irina; Vomvoris, Stratis; Martin, Andrew J.; Smith, Paul

    2011-01-01

    The development of scenarios for quantitative or qualitative analysis is a key element of the assessment of the safety of geological disposal systems. As an outcome of an international workshop attended by European and the Japanese implementers, a number of features common to current methodologies could be identified, as well as trends in their evolution over time. In the late nineties, scenario development was often described as a bottom-up process, whereby scenarios were said to be developed in essence from FEP databases. Nowadays, it is recognised that, in practice, the approaches actually adopted are better described as top-down or 'hybrid', taking as their starting point an integrated (top-down) understanding of the system under consideration including uncertainties in initial state, sometimes assisted by the development of 'storyboards'. A bottom-up element remains (hence the term 'hybrid') to the extent that FEP databases or FEP catalogues (including interactions) are still used, but the focus is generally on completeness checking, which occurs parallel to the main assessment process. Recent advances focus on the consistent treatment of uncertainties throughout the safety assessment and on the integration of operational safety and long term safety. (author)

  5. An integrated approach of composting methodologies for solid waste management

    Directory of Open Access Journals (Sweden)

    K. Kumaresan

    2016-03-01

    Full Text Available Organic fraction of solid waste, which upon degradation produces foul smell and generates pathogens, if not properly managed. Composting is not a method of waste disposal but it is a method of waste recycling and used for agricultural purposes. An integrated approach of composting methodology was tested for municipal solid waste management. Solid waste first was composted and after 22 days, was further processed by vermicomposting. Samples were routinely taken for analysis of carbon, nitrogen, moisture content, pH and temperature to determine the quality of composting. Decrease in moisture content to 32.1 %, relative decrease in carbon and nitrogen content were also observed. Among the different types of treatment, municipal solid waste + activated sludge integration showed promising results, followed by vermicomposting municipal solid waste + activated sludge combination, compared to the combinations of dried activated sludge, municipal solid waste + activated sludge semisolid and municipal solid waste + sewage water. Thus, windrow composting followed by vermicomposting gave a better result than other methods. Thus this method would serve as a potential alternative for solid waste management.

  6. An integrated approach of composting methodologies for solid waste management

    International Nuclear Information System (INIS)

    Kumaresan, K.; Balan, R.; Sridhar, A.; Aravind, J.; Kanmani, P.

    2016-01-01

    Organic fraction of solid waste, which upon degradation produces foul smell and generates pathogens, if not properly managed. Composting is not a method of waste disposal but it is a method of waste recycling and used for agricultural purposes. An integrated approach of composting methodology was tested for municipal solid waste management. Solid waste first was composted and after 22 days, was further processed by vermicomposting. Samples were routinely taken for analysis of carbon, nitrogen, moisture content, p H and temperature to determine the quality of composting. Decrease in moisture content to 32.1 %, relative decrease in carbon and nitrogen content were also observed. Among the different types of treatment, municipal solid waste + activated sludge integration showed promising results, followed by vermicomposting municipal solid waste + activated sludge combination, compared to the combinations of dried activated sludge, municipal solid waste + activated sludge semisolid and municipal solid waste + sewage water. Thus, windrow composting followed by vermicomposting gave a better result than other methods. Thus this method would serve as a potential alternative for solid waste management.

  7. A novel integrated assessment methodology of urban water reuse.

    Science.gov (United States)

    Listowski, A; Ngo, H H; Guo, W S; Vigneswaran, S

    2011-01-01

    Wastewater is no longer considered a waste product and water reuse needs to play a stronger part in securing urban water supply. Although treatment technologies for water reclamation have significantly improved the question that deserves further analysis is, how selection of a particular wastewater treatment technology relates to performance and sustainability? The proposed assessment model integrates; (i) technology, characterised by selected quantity and quality performance parameters; (ii) productivity, efficiency and reliability criteria; (iii) quantitative performance indicators; (iv) development of evaluation model. The challenges related to hierarchy and selections of performance indicators have been resolved through the case study analysis. The goal of this study is to validate a new assessment methodology in relation to performance of the microfiltration (MF) technology, a key element of the treatment process. Specific performance data and measurements were obtained at specific Control and Data Acquisition Points (CP) to satisfy the input-output inventory in relation to water resources, products, material flows, energy requirements, chemicals use, etc. Performance assessment process contains analysis and necessary linking across important parametric functions leading to reliable outcomes and results.

  8. Methodology of Adaptive Integrated Accounting System in Information Environment

    Directory of Open Access Journals (Sweden)

    Bochulya Tetyana V.

    2013-12-01

    Full Text Available The goal of the article lies in the study of logical and methodological justification of formation of the integrated system of accounting based on realities of the co-ordinated transformation of the society and economy and development of a new knowledge about formation and adjustment of the accounting system in it’s a priori new information competence with expansion of functionality for the justified idea of existence and development of business. Taking developments of the best representatives of the leading scientific society as a basis, the article offers a new vision of organisation of the accounting system, based on the modern projection of information competence and harmonisation of main processes of information service for adaptation of the system for multi-vector inquiries of consumers of information. Pursuant to results of the conducted study, the article makes an effort to change the established opinion about information and professional competences of the accounting system and attach a new qualitative significance to them. The article makes a proposal with respect to calculation of quality of the information system on the basis of key indicators of its information service. It lays the foundation of the prospective study of the problems of building the accounting system in such a projection, so that realities of internal and external processes were maximally co-ordinated based on the idea of their information development.

  9. Project INTEGRATE - a common methodological approach to understand integrated health care in Europe

    Directory of Open Access Journals (Sweden)

    Lucinda Cash-Gibson

    2014-12-01

    Full Text Available Background: The use of case studies in health services research has proven to be an excellent methodology for gaining in-depth understanding of the organisation and delivery of health care. This is particularly relevant when looking at the complexity of integrated healthcare programmes, where multifaceted interactions occur at the different levels of care and often without a clear link between the interventions (new and/or existing and their impact on outcomes (in terms of patients health, both patient and professional satisfaction and cost-effectiveness. Still, integrated care is seen as a core strategy in the sustainability of health and care provision in most societies in Europe and beyond. More specifically, at present, there is neither clear evidence on transferable factors of integrated care success nor a method for determining how to establish these specific success factors. The drawback of case methodology in this case, however, is that the in-depth results or lessons generated are usually highly context-specific and thus brings the challenge of transferability of findings to other settings, as different health care systems and different indications are often not comparable. Project INTEGRATE, a European Commission-funded project, has been designed to overcome these problems; it looks into four chronic conditions in different European settings, under a common methodology framework (taking a mixed-methods approach to try to overcome the issue of context specificity and limited transferability. The common methodological framework described in this paper seeks to bring together the different case study findings in a way that key lessons may be derived and transferred between countries, contexts and patient-groups, where integrated care is delivered in order to provide insight into generalisability and build on existing evidence in this field.Methodology: To compare the different integrated care experiences, a mixed-methods approach has

  10. Reliability evaluation methodologies for ensuring container integrity of stored transuranic (TRU) waste

    International Nuclear Information System (INIS)

    Smith, K.L.

    1995-06-01

    This report provides methodologies for providing defensible estimates of expected transuranic waste storage container lifetimes at the Radioactive Waste Management Complex. These methodologies can be used to estimate transuranic waste container reliability (for integrity and degradation) and as an analytical tool to optimize waste container integrity. Container packaging and storage configurations, which directly affect waste container integrity, are also addressed. The methodologies presented provide a means for demonstrating Resource Conservation and Recovery Act waste storage requirements

  11. Value and Vision-based Methodology in Integrated Design

    DEFF Research Database (Denmark)

    Tollestrup, Christian

    on empirical data from workshop where the Value and Vision-based methodology has been taught. The research approach chosen for this investigation is Action Research, where the researcher plays an active role in generating the data and gains a deeper understanding of the investigated phenomena. The result...... of this thesis is the value transformation from an explicit set of values to a product concept using a vision based concept development methodology based on the Pyramid Model (Lerdahl, 2001) in a design team context. The aim of this thesis is to examine how the process of value transformation is occurring within...... is divided in three; the systemic unfolding of the Value and Vision-based methodology, the structured presentation of practical implementation of the methodology and finally the analysis and conclusion regarding the value transformation, phenomena and learning aspects of the methodology....

  12. Trimming and clustering sugarcane ESTs

    Directory of Open Access Journals (Sweden)

    Guilherme P. Telles

    2001-12-01

    Full Text Available The original clustering procedure adopted in the Sugarcane Expressed Sequence Tag project (SUCEST had many problems, for instance too many clusters, the presence of ribosomal sequences, etc. We therefore redesigned the clustering procedure entirely, including a much more careful initial trimming of the reads. In this paper the new trimming and clustering strategies are described in detail and we give the new official figures for the project, 237,954 expressed sequence tags and 43,141 clusters.O método de clustering adotado no Projeto SUCEST (Sugarcane EST Project tinha vários problemas (muitos clusters, presença de seqüências de ribossomo etc. Nós assumimos a tarefa de reprojetar todo o processo de clustering, propondo uma "limpeza" inicial mais cuidadosa das seqüências. Neste artigo as estratégias de limpeza das seqüências e de clustering são descritas em detalhe, incluindo os números oficiais do projeto (237,954 ESTs e 43,141 clusters.

  13. Resistor trimming geometry; past, present and future

    International Nuclear Information System (INIS)

    Alafogianni, M; Penlington, R; Birkett, M

    2016-01-01

    This paper explores the key developments in thin film resistive trimming geometry for use in the fabrication of discrete precision resistors. Firstly an introduction to the laser trimming process is given with respect to well established trim geometries such as the plunge, 'L' and serpentine cuts. The effect of these trim patterns on key electrical properties of resistance tolerance and temperature co-efficient of resistance (TCR) of the thin films is then discussed before the performance of more recent geometries such as the three-contact and random trim approaches are reviewed. In addition to the properties of the standard trim patterns, the concept of the heat affected zone (HAZ) and ablation energy and the effect of introducing a 'fine' trim in areas of low current density to improve device performance are also studied. It is shown how trimming geometry and laser parameters can be systematically controlled to produce thin film resistors of the required properties for varying applications such as high precision, long term stability and high power pulse performance

  14. 14 CFR 23.677 - Trim systems.

    Science.gov (United States)

    2010-01-01

    ... to the pilot the position of the trim device with respect to both the range of adjustment and, in the... a position or range within which it has been demonstrated that take-off is safe for all center of gravity positions and each flap position approved for takeoff. (b) Trimming devices must be designed so...

  15. Origin and diversification of TRIM ubiquitin ligases.

    Directory of Open Access Journals (Sweden)

    Ignacio Marín

    Full Text Available Most proteins of the TRIM family (also known as RBCC family are ubiquitin ligases that share a peculiar protein structure, characterized by including an N-terminal RING finger domain closely followed by one or two B-boxes. Additional protein domains found at their C termini have been used to classify TRIM proteins into classes. TRIMs are involved in multiple cellular processes and many of them are essential components of the innate immunity system of animal species. In humans, it has been shown that mutations in several TRIM-encoding genes lead to diverse genetic diseases and contribute to several types of cancer. They had been hitherto detected only in animals. In this work, by comprehensively analyzing the available diversity of TRIM and TRIM-like protein sequences and evaluating their evolutionary patterns, an improved classification of the TRIM family is obtained. Members of one of the TRIM subfamilies defined, called Subfamily A, turn to be present not only in animals, but also in many other eukaryotes, such as fungi, apusozoans, alveolates, excavates and plants. The rest of subfamilies are animal-specific and several of them originated only recently. Subfamily A proteins are characterized by containing a MATH domain, suggesting a potential evolutionary connection between TRIM proteins and a different type of ubiquitin ligases, known as TRAFs, which contain quite similar MATH domains. These results indicate that the TRIM family emerged much earlier than so far thought and contribute to our understanding of its origin and diversification. The structural and evolutionary links with the TRAF family of ubiquitin ligases can be experimentally explored to determine whether functional connections also exist.

  16. Human-Systems Integration (HSI) Methodology Development for NASA

    Data.gov (United States)

    National Aeronautics and Space Administration — Human-Systems Integration (HSI) refers to design activities associated with ensuring that manpower, personnel, training, human factors engineering, safety, health...

  17. Analyzing the Feasibility of Using Secure Application Integration Methodology (SAIM) for Integrating DON Enterprise Resource Planning (ERP) Applications

    National Research Council Canada - National Science Library

    Marin, Ramon

    2004-01-01

    ...) would provide useful information about a beneficial methodology. SAIM is analyzed, by accessing its step by step directions, for suitability in the integration of the Enterprise Resource Planning (ERP...

  18. A vision on methodology for integrated sustainable urban development: bequest

    NARCIS (Netherlands)

    Bentivegna, V.; Curwell, S.; Deakin, M.; Lombardi, P.; Mitchell, G.; Nijkamp, P.

    2002-01-01

    The concepts and visions of sustainable development that have emerged in the post-Brundtland era are explored in terms laying the foundations for a common vision of sustainable urban development (SUD). The described vision and methodology for SUD resulted from the activities of an international

  19. Assessment of Wind Turbine Structural Integrity using Response Surface Methodology

    DEFF Research Database (Denmark)

    Toft, Henrik Stensgaard; Svenningsen, Lasse; Moser, Wolfgang

    2016-01-01

    Highlights •A new approach to assessment of site specific wind turbine loads is proposed. •The approach can be applied in both fatigue and ultimate limit state. •Two different response surface methodologies have been investigated. •The model uncertainty introduced by the response surfaces...

  20. Integral Design methodology for Industrial Collaboration Design of Sustainable Industrial Flexible Demountable buildings

    NARCIS (Netherlands)

    Zeiler, W.; Quanjel, E.M.C.J.; Bauer, M.; Lima, C.

    2007-01-01

    Starting in 1998 from developing and designing their own office Kropman, a major Dutch Building Services contractor, developed a new methodology for structuring and documenting integral design processes. Integral design is meant to integrate the different disciplines involved in the building design

  1. Design of Sustainable Blended Products using an Integrated Methodology

    DEFF Research Database (Denmark)

    Yunus, Nor Alafiza Binti; Gernaey, Krist; Woodley, John

    2013-01-01

    This paper presents a systematic methodology for designing blended products consisting of three stages; product design, process identification and experimental verification. The product design stage is considered in this paper. The objective of this stage is to screen and select suitable chemicals...... to be used as building blocks in the mixture design, and then to propose the blend formulations that fulfill the desired product attributes. The result is a set of blends that match the constraints, the compositions, values of the target properties and information about their miscibility. The methodology has...... been applied to design several blended products. A case study on design of blended lubricants is highlighted. The objective is to identify blended products that satisfy the product attributes with at least similar or better performance compared to conventional products....

  2. Are Earth Sciences lagging behind in data integration methodologies?

    CSIR Research Space (South Africa)

    Paasche, H

    2013-11-01

    Full Text Available This article reflects discussions German and South African Earth scientists, statisticians and risk analysts had on occasion of two bilateral workshops on Data Integration Technologies for Earth System Modelling and Resource Management...

  3. Resistive RAMs as analog trimming elements

    Science.gov (United States)

    Aziza, H.; Perez, A.; Portal, J. M.

    2018-04-01

    This work investigates the use of Resistive Random Access Memory (RRAM) as an analog trimming device. The analog storage feature of the RRAM cell is evaluated and the ability of the RRAM to hold several resistance states is exploited to propose analog trim elements. To modulate the memory cell resistance, a series of short programming pulses are applied across the RRAM cell allowing a fine calibration of the RRAM resistance. The RRAM non volatility feature makes the analog device powers up already calibrated for the system in which the analog trimmed structure is embedded. To validate the concept, a test structure consisting of a voltage reference is evaluated.

  4. A changing climate: impacts on human exposures to O3 using an integrated modeling methodology

    Science.gov (United States)

    Predicting the impacts of changing climate on human exposure to air pollution requires future scenarios that account for changes in ambient pollutant concentrations, population sizes and distributions, and housing stocks. An integrated methodology to model changes in human exposu...

  5. Integrated vehicle-based safety systems light-vehicle field operational test, methodology and results report.

    Science.gov (United States)

    2010-12-01

    "This document presents the methodology and results from the light-vehicle field operational test conducted as part of the Integrated Vehicle-Based Safety Systems program. These findings are the result of analyses performed by the University of Michi...

  6. Integrated approach methodology: A handbook for power plant assessment

    International Nuclear Information System (INIS)

    Roush, M.L.; Modarres, M.; Hunt, R.N.M.; Kreps, D.; Pearce, R.

    1987-10-01

    This handbook is a practical document that provides the principles and steps of a method to help a utility's decision-making process on matters concerning plant safety and economy. It provides a framework for analyzing the manner in which plant equipment and personnel work together to achieve successful operation; also making possible the quantitative evaluation of individual contributors to success in overall plant operation. The methodology does not purport to instruct utilities on the proper way to run a power plant. Rather, it is an analytical tool to aid a utility in using plant data and other hands-on knowledge of its own personnel to solve practical problems

  7. The integrated approach methodology for operator information evaluation

    International Nuclear Information System (INIS)

    Stroube, K.; Modarres, M.; Roush, M.; Hunt, N.; Pearce, R.

    1986-01-01

    The Integrated Approach has developed a complete method for evaluating the relative importance of operation information improvements. By use of decision trees the impact of information on success probability of a function or system can be evaluated. This approach couples goal trees and human success likelihoods to estimate anticipated consequences of a given information system

  8. Peak-Seeking Control for Trim Optimization

    Data.gov (United States)

    National Aeronautics and Space Administration — Innovators have developed a peak-seeking algorithm that can reduce drag and improve performance and fuel efficiency by optimizing aircraft trim in real time. The...

  9. Trim waste minimization at the Pinellas Plant

    International Nuclear Information System (INIS)

    DeLaneuville, D.

    1992-01-01

    Bacteria counts and several methods of slowing bacterial growth in machine trim coolant are suggested to reduce the frequency of coolant replacement without risking employee health or the longevity of the product or machinery. On-site treatment and disposal of waste trim are recommended to further reduce waste volume. This paper discusses the benefits of these efforts, including projected cost savings based on partial implementation at the Department of Energy's Pinellas Plant

  10. Proposal of Integrated Safety Assessment Methodology for Embedded System

    International Nuclear Information System (INIS)

    Sun, Wei; Kageyama, Makoto; Kanemoto, Shigeru

    2011-01-01

    To do risk analysis and risk evaluation for complicated safety critical embedded systems, there are three things should be paid a good attention: 1) an efficient and integrated model expression of embedded systems: 2) systematic risk analysis based on integrated system model: 3) quantitative risk evaluation for software and hardware integrated system. In this paper, taken electric water boiler as a target system, a proposal of risk analysis and risk evaluation for the embedded system is presented to meet these three purposes. In risk analysis, MFM is used and FT is generated automatically from MFM following some rules: And in risk evaluation, GO-FLOW is used to evaluate the reliability of sensors. And furthermore, FIT is applied to evaluate the safety software logic based on the diversity design concept. Although the electric water boiler is a simple example, it includes the key components of the embedded system like sensors, actuators, and software component. So, the process of modeling, analysis, and evaluation could be applied to other kinds of complicated embedded systems

  11. GO-FLOW methodology. Basic concept and integrated analysis framework for its applications

    International Nuclear Information System (INIS)

    Matsuoka, Takeshi

    2010-01-01

    GO-FLOW methodology is a success oriented system analysis technique, and is capable of evaluating a large system with complex operational sequences. Recently an integrated analysis framework of the GO-FLOW has been developed for the safety evaluation of elevator systems by the Ministry of Land, Infrastructure, Transport and Tourism, Japanese Government. This paper describes (a) an Overview of the GO-FLOW methodology, (b) Procedure of treating a phased mission problem, (c) Common cause failure analysis, (d) Uncertainty analysis, and (e) Integrated analysis framework. The GO-FLOW methodology is a valuable and useful tool for system reliability analysis and has a wide range of applications. (author)

  12. A METHODOLOGICAL MODEL FOR INTEGRATING CHARACTER WITHIN CONTENT AND LANGUAGE INTEGRATED LEARNING IN SOCIOLOGY OF RELIGION

    Directory of Open Access Journals (Sweden)

    Moh Yasir Alimi

    2014-02-01

    Full Text Available AbstractIn this article, I describe a methodological model I used in a experimental study on how to integrate character within the practice of Content and Language Integrated Learning (CLIL at the higher education Indonesia.This research can be added to research about character education and CLIL in tertiary education, giving nuances to the practice of CLIL so far predominantly a practice in primary and secondary schools.The research was conducted in Semarang State University, in the Department of Sociology and Anthropology, in Sociology of Religion bilingual class. The research indicates that the integration of character within CLIL enrich the perspective of CLIL by strengthening the use of CLIL for intellectual growth and moral development. On the other side, the use of CLIL with character education gives methods and perspectives to the practice of character education which so far only emphasise contents reforms without learning methods reforms. The research also reveals that the weakness of CLIL in using text for classroom learning can be overcome by the use of specific reading and writing strategies. I develop a practical text strategy which can be effectively used in highly conceptual subject such as sociology of religion. AbstrakArtikel ini bertujuan untuk mendeskripsikan model metodologis yang saya pakai untuk mengintegrasikannya karakter dalam Content and Language Integrated Learning (CLIL pada pendidikan tinggi di Indonesia. Penelitian ini memperkaya penelitian mengenai pendidikan karakter dan penerapan CLIL di perguruan tinggi, selama ini penelitian semacam itu hanya biasa di level lebih rendah. Penelitian dilakukan di Universitas Negeri Semarang, pada kelas bilingual yang diikuti 25 mahasiswa, dan diujikan pada mata kuliah Sosiologi Agama. Pelajaran dari penelitian ini adalah integrasi karakter dalam CLIL dapat memperkaya CLIL. Sebaliknya penggunaan CLIL untuk mendidikkan karakter di kelas bilingual mampu menjawab berbagai tantangan

  13. Airplane automatic control force trimming device for asymmetric engine failures

    Science.gov (United States)

    Stewart, Eric C. (Inventor)

    1987-01-01

    The difference in dynamic pressure in the propeller slipstreams as measured by sensors is divided by the freestream dynamic pressure generating a quantity proportional to the differential thrust coefficient. This quantity is used to command an electric trim motor to change the position of trim tab thereby retrimming the airplane to the new asymmetric power condition. The change in position of the trim tab produced by the electric trim motor is summed with the pilot's input to produce the actual trim tab position.

  14. On the Integration of Academic and Artistic Methodologies

    DEFF Research Database (Denmark)

    Heinrich, Falk

    2013-01-01

    The paper reflects upon the integration of academic-scientific methods and artistic strategies for art and technology projects that address user participation in a socially defined domain. The paper begins by describing its field of inquiry as an extended art field in which artistic enterprises...... (tightly coupled constituents) as a theoretical and heuristic tool for productive interferences between artistic and scientific methods. Art and technology projects operate within a field of existing forms (social patterns, urban spaces, etc.), which must be de-coupled prior to decisions related to new...

  15. A Comparison of Various Software Development Methodologies: Feasibility and Methods of Integration

    Directory of Open Access Journals (Sweden)

    Samir Abou El-Seoud

    2016-12-01

    Full Text Available System development methodologies which have being used in the academic and commercial environments during last two decades have advantages and disadvantages. Researchers had tried to identify objectives, scope …etc. of the methodologies by following different approaches. Each approach has its Limitation, specific interest, coverage …etc. In this paper, we tried to perform a comparative study of those methodologies which are popular and commonly used in banking and commercial environment. We tried in our study to determine objectives, scope, tools and other features of the methodologies. We also, tried to determine how and to what extent the methodologies incorporate the facilities such as project management, cost benefit analysis, documentation …etc. One of the most important aspects of our study was how to integrate the methodologies and develop a global methodology which covers the complete span of the software development life cycle? A prototype system which integrates the selected methodologies has been developed. The developed system helps analysts and designers how to choose suitable tools or to obtain guidelines on what to do in a particular situation. The prototype system has been tested during the development of a software for an ATM “Auto Teller Machine” by selecting and applying SASD methodology during software development. This resulted in the development of high quality and well documented software system.

  16. Integrated modeling and analysis methodology for precision pointing applications

    Science.gov (United States)

    Gutierrez, Homero L.

    2002-07-01

    Space-based optical systems that perform tasks such as laser communications, Earth imaging, and astronomical observations require precise line-of-sight (LOS) pointing. A general approach is described for integrated modeling and analysis of these types of systems within the MATLAB/Simulink environment. The approach can be applied during all stages of program development, from early conceptual design studies to hardware implementation phases. The main objective is to predict the dynamic pointing performance subject to anticipated disturbances and noise sources. Secondary objectives include assessing the control stability, levying subsystem requirements, supporting pointing error budgets, and performing trade studies. The integrated model resides in Simulink, and several MATLAB graphical user interfaces (GUI"s) allow the user to configure the model, select analysis options, run analyses, and process the results. A convenient parameter naming and storage scheme, as well as model conditioning and reduction tools and run-time enhancements, are incorporated into the framework. This enables the proposed architecture to accommodate models of realistic complexity.

  17. The KNOMAD Methodology for Integration of Multi-Disciplinary Engineering Knowledge within Aerospace Production

    NARCIS (Netherlands)

    Curran, R.; Verhagen, W.J.C.; Van Tooren, M.J.L.

    2010-01-01

    The paper is associated with the integration of multi-disciplinary knowledge within a Knowledge Based Engineering (KBE)-enabled design framework. To support this integration effort, the KNOMAD methodology has been devised. KNOMAD stands for Knowledge Optimized Manufacture And Design and is a

  18. Methodology used in the integrated assessment of PIUS-600 safety

    International Nuclear Information System (INIS)

    Fullwood, R.; Higgins, J.; Kroegar, P.

    1993-01-01

    The revolutionary reactor design, PIUS-600 as described in the Preliminary Safety Analysis Report (PSID) was subjected to analysis consisting of Failure Modes, Effects and Criticality Analysis (FMECA), Hazards and Operability (HAZOP) analysis, and conventional engineering review of the stress, neutronics, thermal hydraulics, and corrosion. These results were integrated in the PIUS Intermediate Table (PIT) from which accident initiators and mitigators were identified and categorized into seven estimated frequency intervals. Accident consequences were classified as: CC-1, minor radiological release, CC-2, clad release, CC-3, major release. The systems were analyzed using event sequence diagrams (ESDs) and event trees (ETs). The resulting accident sequences of the ET, were categorized into Event conditions (ECs) based on initiator frequency and combinations of failures. System interactions were considered in the FMECAs, ESDs, ETs and in an interaction table that also identified system safety classifications

  19. Methodology used in the integrated assessment of PIUS-600 safety

    International Nuclear Information System (INIS)

    Fullwood, R.; Higgins, J.; Kroeger, P.

    1993-01-01

    The revolutionary reactor design, PIUS-600 as described in the Preliminary Safety Analysis Report (PSID) was subject to analyses consisting of Failure Modes. Effects and Criticality Analysis (FMECA), Hazards and Operability (HAZOP) analysis, and conventional engineering review of the stress, neutronics, thermal hydraulics, and corrosion. These results were integrated in the PIUS Intermediate Table (PIT) from which accident initiators and mitigators were identified and categorized into seven estimated frequency intervals. Accident consequences were classified as: CC-1, minor radiological release, CC-2, clad release, CC-3, major release. The systems were analyzed using event sequence diagrams (ESDs) and event trees (ETs). The resulting accident sequences of the ET, were categorized into Event conditions (ECs) based on initiator frequency and combinations of failures. System interactions were considered in the FMECAs, ESDs, ETs and in an interaction table that also identified system safety classifications

  20. Methodology for coupling computational fluid dynamics and integral transport neutronics

    International Nuclear Information System (INIS)

    Thomas, J. W.; Zhong, Z.; Sofu, T.; Downar, T. J.

    2004-01-01

    The CFD code STAR-CD was coupled to the integral transport code DeCART in order to provide high-fidelity, full physics reactor simulations. An interface program was developed to perform the tasks of mapping the STAR-CD mesh to the DeCART mesh, managing all communication between STAR-CD and DeCART, and monitoring the convergence of the coupled calculations. The interface software was validated by comparing coupled calculation results with those obtained using an independently developed interface program. An investigation into the convergence characteristics of coupled calculations was performed using several test models on a multiprocessor LINUX cluster. The results indicate that the optimal convergence of the coupled field calculation depends on several factors, to include the tolerance of the STAR-CD solution and the number of DeCART transport sweeps performed before exchanging data between codes. Results for a 3D, multi-assembly PWR problem on 12 PEs of the LINUX cluster indicate the best performance is achieved when the STAR-CD tolerance and number of DeCART transport sweeps are chosen such that the two fields converge at approximately the same rate. (authors)

  1. Methodology of the Integrated Analysis of Company's Financial Status and Its Performance Results

    OpenAIRE

    Mackevičius, Jonas; Valkauskas, Romualdas

    2010-01-01

    Information about company's financial status and its performance results is very important for the objective evaluation of company's position in the market and competitive possibilities in the future. Such information is provided in the financial statement. It is important to apply and investigate this information properly. The methodology of company's financial status and performance results integrated analysis is recommended in this article. This methodology consists of these three elements...

  2. A solar reserve methodology for renewable energy integration studies based on sub-hourly variability analysis

    Energy Technology Data Exchange (ETDEWEB)

    Ibanez, Eduardo; Brinkman, Gregory; Hummon, Marissa [National Renewable Energy Lab. (NREL), Golden, CO (United States); Lew, Debra

    2012-07-01

    Increasing penetration of wind and solar energy are raising concerns among electric system operators because of the variability and uncertainty associated with the power sources. Previous work focused on the quantification of reserves for systems with wind power. This paper presents a new methodology that allows the determination of necessary reserves for high penetrations of photovoltaic power and compares it to the wind-based methodology. The solar reserve methodology was applied to Phase 2 of the Western Wind and Solar Integration Study. A summary of the results is included. (orig.)

  3. The IDEAL (Integrated Design and Engineering Analysis Languages) modeling methodology: Capabilities and Applications

    Science.gov (United States)

    Evers, Ken H.; Bachert, Robert F.

    1987-01-01

    The IDEAL (Integrated Design and Engineering Analysis Languages) modeling methodology has been formulated and applied over a five-year period. It has proven to be a unique, integrated approach utilizing a top-down, structured technique to define and document the system of interest; a knowledge engineering technique to collect and organize system descriptive information; a rapid prototyping technique to perform preliminary system performance analysis; and a sophisticated simulation technique to perform in-depth system performance analysis.

  4. Integrated cost estimation methodology to support high-performance building design

    Energy Technology Data Exchange (ETDEWEB)

    Vaidya, Prasad; Greden, Lara; Eijadi, David; McDougall, Tom [The Weidt Group, Minnetonka (United States); Cole, Ray [Axiom Engineers, Monterey (United States)

    2007-07-01

    Design teams evaluating the performance of energy conservation measures (ECMs) calculate energy savings rigorously with established modelling protocols, accounting for the interaction between various measures. However, incremental cost calculations do not have a similar rigor. Often there is no recognition of cost reductions with integrated design, nor is there assessment of cost interactions amongst measures. This lack of rigor feeds the notion that high-performance buildings cost more, creating a barrier for design teams pursuing aggressive high-performance outcomes. This study proposes an alternative integrated methodology to arrive at a lower perceived incremental cost for improved energy performance. The methodology is based on the use of energy simulations as means towards integrated design and cost estimation. Various points along the spectrum of integration are identified and characterized by the amount of design effort invested, the scheduling of effort, and relative energy performance of the resultant design. It includes a study of the interactions between building system parameters as they relate to capital costs. Several cost interactions amongst energy measures are found to be significant.The value of this approach is demonstrated with alternatives in a case study that shows the differences between perceived costs for energy measures along various points on the integration spectrum. These alternatives show design tradeoffs and identify how decisions would have been different with a standard costing approach. Areas of further research to make the methodology more robust are identified. Policy measures to encourage the integrated approach and reduce the barriers towards improved energy performance are discussed.

  5. Propulsion integration of hypersonic air-breathing vehicles utilizing a top-down design methodology

    Science.gov (United States)

    Kirkpatrick, Brad Kenneth

    In recent years, a focus of aerospace engineering design has been the development of advanced design methodologies and frameworks to account for increasingly complex and integrated vehicles. Techniques such as parametric modeling, global vehicle analyses, and interdisciplinary data sharing have been employed in an attempt to improve the design process. The purpose of this study is to introduce a new approach to integrated vehicle design known as the top-down design methodology. In the top-down design methodology, the main idea is to relate design changes on the vehicle system and sub-system level to a set of over-arching performance and customer requirements. Rather than focusing on the performance of an individual system, the system is analyzed in terms of the net effect it has on the overall vehicle and other vehicle systems. This detailed level of analysis can only be accomplished through the use of high fidelity computational tools such as Computational Fluid Dynamics (CFD) or Finite Element Analysis (FEA). The utility of the top-down design methodology is investigated through its application to the conceptual and preliminary design of a long-range hypersonic air-breathing vehicle for a hypothetical next generation hypersonic vehicle (NHRV) program. System-level design is demonstrated through the development of the nozzle section of the propulsion system. From this demonstration of the methodology, conclusions are made about the benefits, drawbacks, and cost of using the methodology.

  6. Non-local means filter for trim statics

    KAUST Repository

    Huang, Yunsong; Wang, Xin; Schuster, Gerard T.

    2014-01-01

    this problem, we propose a trim statics inspired by the non-local means algorithm originally developed for image denoising. This method differs from the conventional one in two fundamental respects. First, the trim statics are computed by comparing image

  7. The Integration of Project-Based Methodology into Teaching in Machine Translation

    Science.gov (United States)

    Madkour, Magda

    2016-01-01

    This quantitative-qualitative analytical research aimed at investigating the effect of integrating project-based teaching methodology into teaching machine translation on students' performance. Data was collected from the graduate students in the College of Languages and Translation, at Imam Muhammad Ibn Saud Islamic University, Riyadh, Saudi…

  8. Top-down design and verification methodology for analog mixed-signal integrated circuits

    NARCIS (Netherlands)

    Beviz, P.

    2016-01-01

    The current report contains the introduction of a novel Top-Down Design and Verification methodology for AMS integrated circuits. With the introduction of new design and verification flow, more reliable and efficient development of AMS ICs is possible. The assignment incorporated the research on the

  9. Multicriteria decision methodology for selecting technical alternatives in the Mixed Waste Integrated Program

    International Nuclear Information System (INIS)

    Ferrada, J.J.; Berry, J.B.

    1993-11-01

    The US Department of Energy (DOE) Mixed Waste Integrated Program (MWIP) has as one of its tasks the identification of a decision methodology and key decision criteria for the selection methodology. The aim of a multicriteria analysis is to provide an instrument for a systematic evaluation of distinct alternative projects. Determination of this methodology will clarify (1) the factors used to evaluate these alternatives, (2) the evaluator's view of the importance of the factors, and (3) the relative value of each alternative. The selected methodology must consider the Comprehensive Environmental Response Compensation and Liability Act (CERCLA) decision-making criteria for application to the analysis technology subsystems developed by the DOE Office of Technology Development. This report contains a compilation of several decision methodologies developed in various national laboratories, institutions, and universities. The purpose of these methodologies may vary, but the core of the decision attributes are very similar. Six approaches were briefly analyzed; from these six, in addition to recommendations made by the MWIP technical support group leaders and CERCLA, the final decision methodology was extracted. Slight variations are observed in the many methodologies developed by different groups, but most of the analyzed methodologies address similar aspects for the most part. These common aspects were the core of the methodology suggested in this report for use within MWIP for the selection of technologies. The set of criteria compiled and developed for this report have been grouped in five categories: (1) process effectiveness, (2) developmental status, (3) life-cycle cost, (4) implementability, and (5) regulatory compliance

  10. TRIM65 negatively regulates p53 through ubiquitination

    Energy Technology Data Exchange (ETDEWEB)

    Li, Yang [Department of Respiration, The First Hospital of Jilin University, Changchun 130021 (China); Ma, Chengyuan [Department of Neurosurgery, The First Hospital of Jilin University, Changchun 130021 (China); Zhou, Tong [Department of Endocrinology, The First Hospital of Jilin University, Changchun 130021 (China); Liu, Ying [Department of Respiration, The First Hospital of Jilin University, Changchun 130021 (China); Sun, Luyao [Department of Infectious Diseases, The First Hospital of Jilin University, Changchun 130021 (China); Yu, Zhenxiang, E-mail: zhenxiangyu2015@gmail.com [Department of Respiration, The First Hospital of Jilin University, Changchun 130021 (China)

    2016-04-22

    Tripartite-motif protein family member 65 (TRIM65) is an important protein involved in white matter lesion. However, the role of TRIM65 in human cancer remains less understood. Through the Cancer Genome Atlas (TCGA) gene alteration database, we found that TRIM65 is upregulated in a significant portion of non-small cell lung carcinoma (NSCLC) patients. Our cell growth assay revealed that TRIM65 overexpression promotes cell proliferation, while knockdown of TRIM65 displays opposite effect. Mechanistically, TRIM65 binds to p53, one of the most critical tumor suppressors, and serves as an E3 ligase toward p53. Consequently, TRIM65 inactivates p53 through facilitating p53 poly-ubiquitination and proteasome-mediated degradation. Notably, chemotherapeutic reagent cisplatin induction of p53 is markedly attenuated in response to ectopic expression of TRIM65. Cell growth inhibition by TRIM65 knockdown is more significant in p53 positive H460 than p53 negative H1299 cells, and knockdown of p53 in H460 cells also shows compromised cell growth inhibition by TRIM65 knockdown, indicating that p53 is required, at least in part, for TRIM65 function. Our findings demonstrate TRIM65 as a potential oncogenic protein, highly likely through p53 inactivation, and provide insight into development of novel approaches targeting TRIM65 for NSCLC treatment, and also overcoming chemotherapy resistance. - Highlights: • TRIM65 expression is elevated in NSCLC. • TRIM65 inactivates p53 through mediating p53 ubiquitination and degradation. • TRIM65 attenuates the response of NSCLC cells to cisplatin.

  11. Automatic Edging and Trimming of Hardwood Lumber

    Science.gov (United States)

    D. Earl Kline; Eugene M. Wengert; Philip A. Araman

    1990-01-01

    Studies have shown that there is a potential to increase hardwood lumber value by more than 20 percent through optimum edging and trimming. Even a small portion of this percentage can boost the profitability of hardwood lumber manufacturers substantially. The objective of this research project is to develop an automated system which would assist in correct edging and...

  12. 14 CFR 25.255 - Out-of-trim characteristics.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Out-of-trim characteristics. 25.255 Section 25.255 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT...-trim characteristics. (a) From an initial condition with the airplane trimmed at cruise speeds up to...

  13. An integrated methodology for characterizing flow and transport processes in fractured rock

    International Nuclear Information System (INIS)

    Wu, Yu-Shu

    2007-01-01

    To investigate the coupled processes involved in fluid and heat flow and chemical transport in the highly heterogeneous, unsaturated-zone (UZ) fractured rock of Yucca Mountain, we present an integrated modeling methodology. This approach integrates a wide variety of moisture, pneumatic, thermal, and geochemical isotopic field data into a comprehensive three-dimensional numerical model for modeling analyses. The results of field applications of the methodology show that moisture data, such as water potential and liquid saturation, are not sufficient to determine in situ percolation flux, whereas temperature and geochemical isotopic data provide better constraints to net infiltration rates and flow patterns. In addition, pneumatic data are found to be extremely valuable in estimating large-scale fracture permeability. The integration of hydrologic, pneumatic, temperature, and geochemical data into modeling analyses is thereby demonstrated to provide a practical modeling approach for characterizing flow and transport processes in complex fractured formations

  14. A Methodology for Conducting Integrative Mixed Methods Research and Data Analyses

    Science.gov (United States)

    Castro, Felipe González; Kellison, Joshua G.; Boyd, Stephen J.; Kopak, Albert

    2011-01-01

    Mixed methods research has gained visibility within the last few years, although limitations persist regarding the scientific caliber of certain mixed methods research designs and methods. The need exists for rigorous mixed methods designs that integrate various data analytic procedures for a seamless transfer of evidence across qualitative and quantitative modalities. Such designs can offer the strength of confirmatory results drawn from quantitative multivariate analyses, along with “deep structure” explanatory descriptions as drawn from qualitative analyses. This article presents evidence generated from over a decade of pilot research in developing an integrative mixed methods methodology. It presents a conceptual framework and methodological and data analytic procedures for conducting mixed methods research studies, and it also presents illustrative examples from the authors' ongoing integrative mixed methods research studies. PMID:22167325

  15. A brief history of TRIM5alpha.

    Science.gov (United States)

    Newman, Ruchi M; Johnson, Welkin E

    2007-01-01

    In spite of the fact that the first isolates of HIV-1 became available more than 20 years ago, there is still no robust animal model for HIV-1 replication and pathogenesis. This is largely due to the existence of multiple genetic barriers to HIV-1 replication in most nonhuman primates, including a severe block targeting the early, post-entry phase of the viral replication cycle. It is now known that a protein called TRIM5alpha mediates this early restriction in nonhuman primate cells. Tissue culture experiments, together with genetic association studies involving multiple HIV/AIDS cohorts, indicate that the human orthologue of TRIM5alpha does not have a significant impact on HIV-1 replication. However, most human alleles encode a functional protein that can restrict at least one retrovirus unrelated to HIV-1 (N-tropic murine leukemia virus), although one deleterious mutation (H43Y) is present at high frequency in human populations. Phylogenetic analyses of the TRIM5 locus reveal that prehistoric retroviral epidemics, not unlike the current HIV/AIDS pandemic, played a significant role in the evolutionary history of humans and their primate relatives. The discovery of TRIM5alpha's antiretroviral activity sparked the imaginations of many laboratories, and considerable effort has now been channeled into characterizing the protein and determining its possible mechanism(s) of action. It is hoped that research on TRIM5alpha will contribute to the establishment of new and improved models for HIV replication and AIDS pathogenesis, point the way towards novel therapeutic targets to stem the tide of the human AIDS epidemic, provide an experimental window onto the early, post-entry stages of the retroviral replication cycle, and even inspire the search for other cellular factors that modulate retroviral infection.

  16. An integrated methodology for the dynamic performance and reliability evaluation of fault-tolerant systems

    International Nuclear Information System (INIS)

    Dominguez-Garcia, Alejandro D.; Kassakian, John G.; Schindall, Joel E.; Zinchuk, Jeffrey J.

    2008-01-01

    We propose an integrated methodology for the reliability and dynamic performance analysis of fault-tolerant systems. This methodology uses a behavioral model of the system dynamics, similar to the ones used by control engineers to design the control system, but also incorporates artifacts to model the failure behavior of each component. These artifacts include component failure modes (and associated failure rates) and how those failure modes affect the dynamic behavior of the component. The methodology bases the system evaluation on the analysis of the dynamics of the different configurations the system can reach after component failures occur. For each of the possible system configurations, a performance evaluation of its dynamic behavior is carried out to check whether its properties, e.g., accuracy, overshoot, or settling time, which are called performance metrics, meet system requirements. Markov chains are used to model the stochastic process associated with the different configurations that a system can adopt when failures occur. This methodology not only enables an integrated framework for evaluating dynamic performance and reliability of fault-tolerant systems, but also enables a method for guiding the system design process, and further optimization. To illustrate the methodology, we present a case-study of a lateral-directional flight control system for a fighter aircraft

  17. Design of an Integrated Methodology for Analytical Design of Complex Supply Chains

    Directory of Open Access Journals (Sweden)

    Shahid Rashid

    2012-01-01

    Full Text Available A literature review and gap analysis indentifies key limitations of industry best practice when modelling of supply chains. To address these limitations the paper reports on the conception and development of an integrated modelling methodology designed to underpin the analytical design of complex supply chains. The methodology is based upon a systematic deployment of EM, CLD, and SM techniques; the integration of which is achieved via common modelling concepts and decomposition principles. Thereby the methodology facilitates: (i graphical representation and description of key “processing”, “resourcing” and “work flow” properties of supply chain configurations; (ii behavioural exploration of currently configured supply chains, to facilitate reasoning about uncertain demand impacts on supply, make, delivery, and return processes; (iii predictive quantification about relative performances of alternative complex supply chain configurations, including risk assessments. Guidelines for the application of each step of the methodology are described. Also described are recommended data collection methods and expected modelling outcomes for each step. The methodology is being extensively case tested to quantify potential benefits & costs relative to current best industry practice. The paper reflects on preliminary benefits gained during industry based case study modelling and identifies areas of potential improvement.

  18. Innovation and Integrity in Intervention Research: Conceptual Issues, Methodology, and Knowledge Translation.

    Science.gov (United States)

    Malti, Tina; Beelmann, Andreas; Noam, Gil G; Sommer, Simon

    2018-04-01

    In this article, we introduce the special issue entitled Innovation and Integrity in Intervention Science. Its focus is on essential problems and prospects for intervention research examining two related topics, i.e., methodological issues and research integrity, and challenges in the transfer of research knowledge into practice and policy. The main aims are to identify how to advance methodology in order to improve research quality, examine scientific integrity in the field of intervention science, and discuss future steps to enhance the transfer of knowledge about evidence-based intervention principles into sustained practice, routine activities, and policy decisions. Themes of the special issue are twofold. The first includes questions about research methodology in intervention science, both in terms of research design and methods, as well as data analyses and the reporting of findings. Second, the issue tackles questions surrounding the types of knowledge translation frameworks that might be beneficial to mobilize the transfer of research-based knowledge into practice and public policies. The issue argues that innovations in methodology and thoughtful approaches to knowledge translation can enable transparency, quality, and sustainability of intervention research.

  19. Methodology for optimization of process integration schemes in a biorefinery under uncertainty

    International Nuclear Information System (INIS)

    Marta Abreu de las Villas (Cuba))" data-affiliation=" (Departamento de Ingeniería Química. Facultad de Química y Farmacia. Universidad Central Marta Abreu de las Villas (Cuba))" >González-Cortés, Meilyn; Marta Abreu de las Villas (Cuba))" data-affiliation=" (Departamento de Ingeniería Química. Facultad de Química y Farmacia. Universidad Central Marta Abreu de las Villas (Cuba))" >Martínez-Martínez, Yenisleidys; Marta Abreu de las Villas (Cuba))" data-affiliation=" (Departamento de Ingeniería Química. Facultad de Química y Farmacia. Universidad Central Marta Abreu de las Villas (Cuba))" >Albernas-Carvajal, Yailet; Marta Abreu de las Villas (Cuba))" data-affiliation=" (Departamento de Ingeniería Química. Facultad de Química y Farmacia. Universidad Central Marta Abreu de las Villas (Cuba))" >Pedraza-Garciga, Julio; Marta Abreu de las Villas (Cuba))" data-affiliation=" (Departamento de Ingeniería Química. Facultad de Química y Farmacia. Universidad Central Marta Abreu de las Villas (Cuba))" >Morales-Zamora, Marlen

    2017-01-01

    The uncertainty has a great impact in the investment decisions, operability of the plants and in the feasibility of integration opportunities in the chemical processes. This paper, presents the steps to consider the optimization of process investment in the processes integration under conditions of uncertainty. It is shown the potentialities of the biomass cane of sugar for the integration with several plants in a biorefinery scheme for the obtaining chemical products, thermal and electric energy. Among the factories with potentialities for this integration are the pulp and paper and sugar factories and other derivative processes. Theses factories have common resources and also have a variety of products that can be exchange between them so certain products generated in a one of them can be raw matter in another plant. The methodology developed guide to obtaining of feasible investment projects under uncertainty. As objective function was considered the maximization of net profitable value in different scenarios that are generated from the integration scheme. (author)

  20. Application of the integrated safety assessment methodology to the protection of electric systems

    International Nuclear Information System (INIS)

    Hortal, Javier; Izquierdo, Jose M.

    1996-01-01

    The generalization of classical techniques for risk assessment incorporating dynamic effects is the main objective of the Integrated Safety Assessment Methodology, as practical implementation of Protection Theory. Transient stability, contingency analysis and protection setpoint verification in electric power systems are particularly appropriate domains of application, since the coupling of reliability and dynamic analysis in the protection assessment process is being increasingly demanded. Suitable techniques for dynamic simulation of sequences of switching events in power systems are derived from the use of quasi-linear equation solution algorithms. The application of the methodology, step by step, is illustrated in a simple but representative example

  1. Methodological Bases for Describing Risks of the Enterprise Business Model in Integrated Reporting

    Directory of Open Access Journals (Sweden)

    Nesterenko Oksana O.

    2017-12-01

    Full Text Available The aim of the article is to substantiate the methodological bases for describing the business and accounting risks of an enterprise business model in integrated reporting for their timely detection and assessment, and develop methods for their leveling or minimizing and possible prevention. It is proposed to consider risks in the process of forming integrated reporting from two sides: first, risks that arise in the business model of an organization and should be disclosed in its integrated report; second, accounting risks of integrated reporting, which should be taken into account by members of the cross-sectoral working group and management personnel in the process of forming and promulgating integrated reporting. To develop an adequate accounting and analytical tool for disclosure of information about the risks of the business model and integrated reporting, their leveling or minimization, in the article a terminological analysis of the essence of entrepreneurial and accounting risks is carried out. The entrepreneurial risk is defined as an objective-subjective economic category that characterizes the probability of negative or positive consequences of economic-social-ecological activity within the framework of the business model of an enterprise under uncertainty. The accounting risk is suggested to be understood as the probability of unfavorable consequences as a result of organizational, methodological errors in the integrated accounting system, which present threat to the quality, accuracy and reliability of the reporting information on economic, social and environmental activities in integrated reporting as well as threat of inappropriate decision-making by stakeholders based on the integrated report. For the timely identification of business risks and maximum leveling of the influence of accounting risks on the process of formation and publication of integrated reporting, in the study the place of entrepreneurial and accounting risks in

  2. Fusion integral experiments and analysis and the determination of design safety factors - I: Methodology

    International Nuclear Information System (INIS)

    Youssef, M.Z.; Kumar, A.; Abdou, M.A.; Oyama, Y.; Maekawa, H.

    1995-01-01

    The role of the neutronics experimentation and analysis in fusion neutronics research and development programs is discussed. A new methodology was developed to arrive at estimates to design safety factors based on the experimental and analytical results from design-oriented integral experiments. In this methodology, and for a particular nuclear response, R, a normalized density function (NDF) is constructed from the prediction uncertainties, and their associated standard deviations, as found in the various integral experiments where that response, R, is measured. Important statistical parameters are derived from the NDF, such as the global mean prediction uncertainty, and the possible spread around it. The method of deriving safety factors from many possible NDFs based on various calculational and measuring methods (among other variants) is also described. Associated with each safety factor is a confidence level, designers may choose to have, that the calculated response, R, will not exceed (or will not fall below) the actual measured value. An illustrative example is given on how to construct the NDFs. The methodology is applied in two areas, namely the line-integrated tritium production rate and bulk shielding integral experiments. Conditions under which these factors could be derived and the validity of the method are discussed. 72 refs., 17 figs., 4 tabs

  3. Environmental integrated impact assessment for waste treatment activity: methodology and case-study application

    International Nuclear Information System (INIS)

    Lonati, G.; Panzeri, A.

    2008-01-01

    A literature method for the environmental integrated impact assessment, according to the IPPC Directive, has been critically analysed and adjusted in order to be used for the environmental performance assessment of waste treatment activities. The assessment parameters, sorted in eight treatment and combined pollution categories, have been partly redefined and re balanced. The adjusted methodology has been applied to a real case-study, a chemical- physical waste treatment plant, in order to calculate the current performance (Actual Integrated Index) and the ideal performance (Actual Integrated Index) achievable by technical and operational improvements. The adjusted methodology has also been used as a decision support system, in order to estimate the value of the expected environmental performances improvement after the execution achievable from the introduction of a single one or a set of improvement actions. The valuation of the Integrated Index percentage reduction, along with the action achievable, made the best actions able to be identified, both in comparative way and in the cost-effective one. The results, 50 as Effective Integrated Index and 42 as Ideal Integrated Index, in a 10-100 scale, show a medium impact level and point out an appreciable improvement margin on all the environmental performances, especially in air emission control and water consumption [it

  4. Integration of an iterative methodology for exergoeconomic improvement of thermal systems with a process simulator

    International Nuclear Information System (INIS)

    Vieira, Leonardo S.; Donatelli, Joao L.; Cruz, Manuel E.

    2004-01-01

    In this paper, we present the development and automated implementation of an iterative methodology for exergoeconomic improvement of thermal systems integrated with a process simulator, so as to be applicable to real, complex plants. The methodology combines recent available exergoeconomic techniques with new qualitative and quantitative criteria for the following tasks: (i) identification of decision variables that affect system total cost and exergetic efficiency; (ii) hierarchical classification of components; (iii) identification of predominant terms in the component total cost; and (iv) choice of main decision variables in the iterative process. To show the strengths and potential advantages of the proposed methodology, it is here applied to the benchmark CGAM cogeneration system. The results obtained are presented and discussed in detail and are compared to those reached using a mathematical optimization procedure

  5. Integrating rock mechanics issues with repository design through design process principles and methodology

    International Nuclear Information System (INIS)

    Bieniawski, Z.T.

    1996-01-01

    A good designer needs not only knowledge for designing (technical know-how that is used to generate alternative design solutions) but also must have knowledge about designing (appropriate principles and systematic methodology to follow). Concepts such as open-quotes design for manufactureclose quotes or open-quotes concurrent engineeringclose quotes are widely used in the industry. In the field of rock engineering, only limited attention has been paid to the design process because design of structures in rock masses presents unique challenges to the designers as a result of the uncertainties inherent in characterization of geologic media. However, a stage has now been reached where we are be able to sufficiently characterize rock masses for engineering purposes and identify the rock mechanics issues involved but are still lacking engineering design principles and methodology to maximize our design performance. This paper discusses the principles and methodology of the engineering design process directed to integrating site characterization activities with design, construction and performance of an underground repository. Using the latest information from the Yucca Mountain Project on geology, rock mechanics and starter tunnel design, the current lack of integration is pointed out and it is shown how rock mechanics issues can be effectively interwoven with repository design through a systematic design process methodology leading to improved repository performance. In essence, the design process is seen as the use of design principles within an integrating design methodology, leading to innovative problem solving. In particular, a new concept of open-quotes Design for Constructibility and Performanceclose quotes is introduced. This is discussed with respect to ten rock mechanics issues identified for repository design and performance

  6. Teaching writing of scientific abstracts in English: CLIL methodology in an integrated English and Medicine course

    Directory of Open Access Journals (Sweden)

    Philippa Mungra

    2010-10-01

    Full Text Available In the I Faculty at the University of Rome “La Sapienza” Medical School, one of the several methodology courses aims at developing approaches by physicians to patient queries. One such course comprises several disciplines: Pathology, Immunology, Medical Statistics, Internal Medicine and English, with the specific aim of furnishing students, all Italian speakers, with skills for searching and evaluating the medical literature for answers to patient queries regarding risks and effectiveness of therapy. This paper describes the integration of English into a Methodology Course and delineates how the language component uses a Content and Language Integrated Learning (CLIL approach to train students to write the highly specific genre of journal abstracts for medical experimental research articles. A corpus of student writing is presented and discussed with the aim of furnishing one didactic model for language teaching within the Italian Medical Curriculum.

  7. How to conduct a qualitative meta-analysis: Tailoring methods to enhance methodological integrity.

    Science.gov (United States)

    Levitt, Heidi M

    2018-05-01

    Although qualitative research has long been of interest in the field of psychology, meta-analyses of qualitative literatures (sometimes called meta-syntheses) are still quite rare. Like quantitative meta-analyses, these methods function to aggregate findings and identify patterns across primary studies, but their aims, procedures, and methodological considerations may vary. This paper explains the function of qualitative meta-analyses and their methodological development. Recommendations have broad relevance but are framed with an eye toward their use in psychotherapy research. Rather than arguing for the adoption of any single meta-method, this paper advocates for considering how procedures can best be selected and adapted to enhance a meta-study's methodological integrity. Through the paper, recommendations are provided to help researchers identify procedures that can best serve their studies' specific goals. Meta-analysts are encouraged to consider the methodological integrity of their studies in relation to central research processes, including identifying a set of primary research studies, transforming primary findings into initial units of data for a meta-analysis, developing categories or themes, and communicating findings. The paper provides guidance for researchers who desire to tailor meta-analytic methods to meet their particular goals while enhancing the rigor of their research.

  8. New methodology for analytical calculation of resonance integrals in an heterogeneous medium

    International Nuclear Information System (INIS)

    Campos, T.P.R. de; Martinez, A.S.

    1986-01-01

    A new methodology for analytical calculation of Resonance Integral in a typical fuel cell is presented. The expression obtained for the Resonance Integral presents the advantage of being analytical. Its constituent terms are combinations of the well known function J(xi,β) with its partial derivatives in regard to β. This is a general expression for all types of resonance. The parameters used in this method depend on the resonance type and are obtained as a function of the parameter lambda. A simple expression, depending on resonance parameters is proposed for this variable. (Author) [pt

  9. QFD: a methodological tool for integration of ergonomics at the design stage.

    Science.gov (United States)

    Marsot, Jacques

    2005-03-01

    As a marked increase in the number of musculoskeletal disorders was noted in many industrialized countries and more specifically in companies that require the use of hand tools, the French National Research and Safety Institute launched in 1999 a research program on the topic of integrating ergonomics into hand tool design. After a brief review of the problems of integrating ergonomics at the design stage, the paper shows how the "Quality Function Deployment" method has been applied to the design of a boning knife and it highlights the difficulties encountered. Then, it demonstrates how this method can be a methodological tool geared to greater ergonomics consideration in product design.

  10. Methodology for Supply Chain Integration: A Case Study in the Artisan Industry of Footwear

    OpenAIRE

    Pérez-Gallardo, Jorge Raúl; Hernández-Vera, Beatriz; Moras Sánchez, Constantino Gerardo; Aguilar Lasserre, Alberto Alfonso; Posada-Gómez, Rubén; Juárez-Martínez, Ulises; Alor-Hernández, Giner

    2014-01-01

    The supply chain is a major issue in a global market. The efficient relationship between supplier-producer-retailer conforms the perfect combination to achieve a high level of competitiveness according to the needs of increasingly demanding and changing markets. The difficulty of synchronizing the members within the SC is related to the inherent uncertain factors. This paper proposes a methodology for integrating the supply chain that can be applied in any type of business. To demonstrate its...

  11. A Methodology to Integrate Security and Cost-effectiveness in ATM

    OpenAIRE

    Matarese, Francesca; Montefusco, Patrizia; Neves, José; Rocha, André

    2014-01-01

    The objective of this paper is the definition of a new methodology for carrying out security risk assessment in the air traffic management (ATM) domain so as to enhance security awareness and integrate secure and cost-effective design objectives. This process is carried out by modelling the system, identifying the assets, threats and vulnerabilities, prioritizing the threats and proposing cost-effective countermeasures for the weaknesses found. ATM security is concerned with securing ATM a...

  12. Methodological procedures and analytical instruments to evaluate an indicators integrated archive for urban management

    International Nuclear Information System (INIS)

    Del Ciello, R.; Napoleoni, S.

    1998-01-01

    This guide provides the results of a research developed at ENEA (National Agency for new Technology, Energy and the Environment) Casaccia center (Rome, Italy) aimed to define methodological procedures and analytical instruments needed to carry out an indicators integrated archive for urban management. The guide also defines the scheme of a negotiation process aimed to reach and exchange data and information among governmental and local administrations, non-governmental organizations and scientific bodies [it

  13. Framework methodology for increased energy efficiency and renewable feedstock integration in industrial clusters

    International Nuclear Information System (INIS)

    Hackl, Roman; Harvey, Simon

    2013-01-01

    Highlights: • Framework methodology for energy efficiency of process plants and total sites. • Identification of suitable biorefinery based on host site future energy systems. • Case study results show large energy savings of site wide heat integration. • Case study on refrigeration systems: 15% shaft work savings potential. • Case study on biorefinery integration: utility savings potential of up to 37%. - Abstract: Energy intensive industries, such as the bulk chemical industry, are facing major challenges and adopting strategies to face these challenges. This paper investigates options for clusters of chemical process plants to decrease their energy and emission footprints. There is a wide range of technologies and process integration opportunities available for achieving these objectives, including (i) decreasing fossil fuel and electricity demand by increasing heat integration within individual processes and across the total cluster site; (ii) replacing fossil feedstocks with renewables and biorefinery integration with the existing cluster; (iii) increasing external utilization of excess process heat wherever possible. This paper presents an overview of the use of process integration methods for development of chemical clusters. Process simulation, pinch analysis, Total Site Analysis (TSA) and exergy concepts are combined in a holistic approach to identify opportunities to improve energy efficiency and integrate renewable feedstocks within such clusters. The methodology is illustrated by application to a chemical cluster in Stenungsund on the West Coast of Sweden consisting of five different companies operating six process plants. The paper emphasizes and quantifies the gains that can be made by adopting a total site approach for targeting energy efficiency measures within the cluster and when investigating integration opportunities for advanced biorefinery concepts compared to restricting the analysis to the individual constituent plants. The

  14. An optimization methodology for identifying robust process integration investments under uncertainty

    International Nuclear Information System (INIS)

    Svensson, Elin; Berntsson, Thore; Stroemberg, Ann-Brith; Patriksson, Michael

    2009-01-01

    Uncertainties in future energy prices and policies strongly affect decisions on investments in process integration measures in industry. In this paper, we present a five-step methodology for the identification of robust investment alternatives incorporating explicitly such uncertainties in the optimization model. Methods for optimization under uncertainty (or, stochastic programming) are thus combined with a deep understanding of process integration and process technology in order to achieve a framework for decision-making concerning the investment planning of process integration measures under uncertainty. The proposed methodology enables the optimization of investments in energy efficiency with respect to their net present value or an environmental objective. In particular, as a result of the optimization approach, complex investment alternatives, allowing for combinations of energy efficiency measures, can be analyzed. Uncertainties as well as time-dependent parameters, such as energy prices and policies, are modelled using a scenario-based approach, enabling the identification of robust investment solutions. The methodology is primarily an aid for decision-makers in industry, but it will also provide insight for policy-makers into how uncertainties regarding future price levels and policy instruments affect the decisions on investments in energy efficiency measures. (author)

  15. An optimization methodology for identifying robust process integration investments under uncertainty

    Energy Technology Data Exchange (ETDEWEB)

    Svensson, Elin; Berntsson, Thore [Department of Energy and Environment, Division of Heat and Power Technology, Chalmers University of Technology, SE-412 96 Goeteborg (Sweden); Stroemberg, Ann-Brith [Fraunhofer-Chalmers Research Centre for Industrial Mathematics, Chalmers Science Park, SE-412 88 Gothenburg (Sweden); Patriksson, Michael [Department of Mathematical Sciences, Chalmers University of Technology and Department of Mathematical Sciences, University of Gothenburg, SE-412 96 Goeteborg (Sweden)

    2009-02-15

    Uncertainties in future energy prices and policies strongly affect decisions on investments in process integration measures in industry. In this paper, we present a five-step methodology for the identification of robust investment alternatives incorporating explicitly such uncertainties in the optimization model. Methods for optimization under uncertainty (or, stochastic programming) are thus combined with a deep understanding of process integration and process technology in order to achieve a framework for decision-making concerning the investment planning of process integration measures under uncertainty. The proposed methodology enables the optimization of investments in energy efficiency with respect to their net present value or an environmental objective. In particular, as a result of the optimization approach, complex investment alternatives, allowing for combinations of energy efficiency measures, can be analyzed. Uncertainties as well as time-dependent parameters, such as energy prices and policies, are modelled using a scenario-based approach, enabling the identification of robust investment solutions. The methodology is primarily an aid for decision-makers in industry, but it will also provide insight for policy-makers into how uncertainties regarding future price levels and policy instruments affect the decisions on investments in energy efficiency measures. (author)

  16. An integrated methodology for process improvement and delivery system visualization at a multidisciplinary cancer center.

    Science.gov (United States)

    Singprasong, Rachanee; Eldabi, Tillal

    2013-01-01

    Multidisciplinary cancer centers require an integrated, collaborative, and stream-lined workflow in order to provide high quality of patient care. Due to the complex nature of cancer care and continuing changes to treatment techniques and technologies, it is a constant struggle for centers to obtain a systemic and holistic view of treatment workflow for improving the delivery systems. Project management techniques, Responsibility matrix and a swim-lane activity diagram representing sequence of activities can be combined for data collection, presentation, and evaluation of the patient care. This paper presents this integrated methodology using multidisciplinary meetings and walking the route approach for data collection, integrated responsibility matrix and swim-lane activity diagram with activity time for data representation and 5-why and gap analysis approach for data analysis. This enables collection of right detail of information in a shorter time frame by identifying process flaws and deficiencies while being independent of the nature of the patient's disease or treatment techniques. A case study of a multidisciplinary regional cancer centre is used to illustrate effectiveness of the proposed methodology and demonstrates that the methodology is simple to understand, allowing for minimal training of staff and rapid implementation. © 2011 National Association for Healthcare Quality.

  17. Determining the number of kanbans for dynamic production systems: An integrated methodology

    Directory of Open Access Journals (Sweden)

    Özlem Uzun Araz

    2016-08-01

    Full Text Available Just-in-time (JIT is a management philosophy that reduces the inventory levels and eliminates manufacturing wastes by producing only the right quantity at the right time. A kanban system is one of the key elements of JIT philosophy. Kanbans are used to authorize production and to control movement of materials in JIT systems. In Kanban systems, the efficiency of the manufacturing system depends on several factors such as number of kanbans, container size etc. Hence, determining the number of kanbans is a critical decision in Kanban systems. The aim of this study is to develop a methodology that can be used in order to determine the number of kanbans in a dynamic production environment. In this methodology, the changes in system state is monitored in real time manner, and the number of the kanbans are dynamically re-arranged. The proposed methodology integrates simulation, neural networks and Mamdani type fuzzy inference system. The methodology is modelled in simulation environment and applied on a hypothetic production system. We also performed several comparisons for different control policies to show the effectiveness of the proposed methodology.

  18. Water level management of lakes connected to regulated rivers: An integrated modeling and analytical methodology

    Science.gov (United States)

    Hu, Tengfei; Mao, Jingqiao; Pan, Shunqi; Dai, Lingquan; Zhang, Peipei; Xu, Diandian; Dai, Huichao

    2018-07-01

    Reservoir operations significantly alter the hydrological regime of the downstream river and river-connected lake, which has far-reaching impacts on the lake ecosystem. To facilitate the management of lakes connected to regulated rivers, the following information must be provided: (1) the response of lake water levels to reservoir operation schedules in the near future and (2) the importance of different rivers in terms of affecting the water levels in different lake regions of interest. We develop an integrated modeling and analytical methodology for the water level management of such lakes. The data-driven method is used to model the lake level as it has the potential of producing quick and accurate predictions. A new genetic algorithm-based synchronized search is proposed to optimize input variable time lags and data-driven model parameters simultaneously. The methodology also involves the orthogonal design and range analysis for extracting the influence of an individual river from that of all the rivers. The integrated methodology is applied to the second largest freshwater lake in China, the Dongting Lake. The results show that: (1) the antecedent lake levels are of crucial importance for the current lake level prediction; (2) the selected river discharge time lags reflect the spatial heterogeneity of the rivers' impacts on lake level changes; (3) the predicted lake levels are in very good agreement with the observed data (RMSE ≤ 0.091 m; R2 ≥ 0.9986). This study demonstrates the practical potential of the integrated methodology, which can provide both the lake level responses to future dam releases and the relative contributions of different rivers to lake level changes.

  19. MODEL - INTEGRAL METHODOLOGY FOR SUCCESSFUL DESIGNING AND IMPLEMENTING OF TQM SYSTEM IN MACEDONIAN COMPANIES

    Directory of Open Access Journals (Sweden)

    Elizabeta Mitreva

    2011-12-01

    Full Text Available The subject of this paper is linked with the valorization of the meaning and the perspectives of Total Quality Management (TQM system design and implementation within the domestic companies and creating a model-methodology for improved performance, efficiency and effectiveness. The research is designed as an attempt to depict the existing condition in the Macedonian companies regarding quality system design and implementation, analysed through 4 polls in the "house of quality" whose top is the ultimate management, and as its bases measurement, evaluation, analyzing and comparison of the quality are used. This "house" is being held by 4 subsystems e.g. internal standardization, methods and techniques for flawless work performance, education and motivation and analyses of the quality costs. The data received from the research and the proposal of the integral methodology for designing and implementing of TQM system are designed in turn to help and present useful directions to all Macedonian companies tending to become "world class" organizations. The basis in the creation of this model is the redesign of the business processes which afterword begins as a new phase of the business performance - continued improvement, rolling of Deming's Quality Circle (Plan-Do-Check-Act. The model-methodology proposed in this paper is integral and universal which means that it is applicable to all companies regardless of the business area.

  20. Development of a methodology for conducting an integrated HRA/PRA --

    International Nuclear Information System (INIS)

    Luckas, W.J.; Barriere, M.T.; Brown, W.S.; Wreathall, J.; Cooper, S.E.

    1993-01-01

    During Low Power and Shutdown (LP ampersand S) conditions in a nuclear power plant (i.e., when the reactor is subcritical or at less than 10--15% power), human interactions with the plant's systems will be more frequent and more direct. Control is typically not mediated by automation, and there are fewer protective systems available. Therefore, an assessment of LP ampersand S related risk should include a greater emphasis on human reliability than such an assessment made for power operation conditions. In order to properly account for the increase in human interaction and thus be able to perform a probabilistic risk assessment (PRA) applicable to operations during LP ampersand S, it is important that a comprehensive human reliability assessment (HRA) methodology be developed and integrated into the LP ampersand S PRA. The tasks comprising the comprehensive HRA methodology development are as follows: (1) identification of the human reliability related influences and associated human actions during LP ampersand S, (2) identification of potentially important LP ampersand S related human actions and appropriate HRA framework and quantification methods, and (3) incorporation and coordination of methodology development with other integrated PRA/HRA efforts. This paper describes the first task, i.e., the assessment of human reliability influences and any associated human actions during LP ampersand S conditions for a pressurized water reactor (PWR)

  1. Multicriteria renewable energy planning using an integrated fuzzy VIKOR and AHP methodology: The case of Istanbul

    International Nuclear Information System (INIS)

    Kaya, Tolga; Kahraman, Cengiz

    2010-01-01

    The purpose of this study is twofold: first, it is aimed at determining the best renewable energy alternative for Istanbul by using an integrated VIKOR-AHP methodology. Second, a selection among alternative energy production sites in this city is made using the same approach. In the proposed VIKOR-AHP methodology, the weights of the selection criteria are determined by pairwise comparison matrices of AHP. In energy decision making problems, the judgments of decision makers are usually vague. As it is relatively difficult for decision makers to provide exact values for the criteria, the evaluation data for the alternative energy policies should be expressed in linguistic terms. In order to model this kind of uncertainty in human preferences, fuzzy logic is applied very successfully. Thus, both classical VIKOR and classical AHP procedures are performed under fuzzy environment. The originality of the paper comes from the application of the proposed integrated VIKOR-AHP methodology to the selection of the best energy policy and production site. It is found that wind energy is the most appropriate renewable energy option and Catalca district is the best area among the alternatives for establishing wind turbines in Istanbul.

  2. Development of a methodology for conducting an integrated HRA/PRA --

    Energy Technology Data Exchange (ETDEWEB)

    Luckas, W.J.; Barriere, M.T.; Brown, W.S. (Brookhaven National Lab., Upton, NY (United States)); Wreathall, J. (Wreathall (John) and Co., Dublin, OH (United States)); Cooper, S.E. (Science Applications International Corp., McLean, VA (United States))

    1993-01-01

    During Low Power and Shutdown (LP S) conditions in a nuclear power plant (i.e., when the reactor is subcritical or at less than 10--15% power), human interactions with the plant's systems will be more frequent and more direct. Control is typically not mediated by automation, and there are fewer protective systems available. Therefore, an assessment of LP S related risk should include a greater emphasis on human reliability than such an assessment made for power operation conditions. In order to properly account for the increase in human interaction and thus be able to perform a probabilistic risk assessment (PRA) applicable to operations during LP S, it is important that a comprehensive human reliability assessment (HRA) methodology be developed and integrated into the LP S PRA. The tasks comprising the comprehensive HRA methodology development are as follows: (1) identification of the human reliability related influences and associated human actions during LP S, (2) identification of potentially important LP S related human actions and appropriate HRA framework and quantification methods, and (3) incorporation and coordination of methodology development with other integrated PRA/HRA efforts. This paper describes the first task, i.e., the assessment of human reliability influences and any associated human actions during LP S conditions for a pressurized water reactor (PWR).

  3. Energy Level Composite Curves-a new graphical methodology for the integration of energy intensive processes

    International Nuclear Information System (INIS)

    Anantharaman, Rahul; Abbas, Own Syed; Gundersen, Truls

    2006-01-01

    Pinch Analysis, Exergy Analysis and Optimization have all been used independently or in combination for the energy integration of process plants. In order to address the issue of energy integration, taking into account composition and pressure effects, the concept of energy level as proposed by [X. Feng, X.X. Zhu, Combining pinch and exergy analysis for process modifications, Appl. Therm. Eng. 17 (1997) 249] has been modified and expanded in this work. We have developed a strategy for energy integration that uses process simulation tools to define the interaction between the various subsystems in the plant and a graphical technique to help the engineer interpret the results of the simulation with physical insights that point towards exploring possible integration schemes to increase energy efficiency. The proposed graphical representation of energy levels of processes is very similar to the Composite Curves of Pinch Analysis-the interpretation of the Energy Level Composite Curves reduces to the Pinch Analysis case when dealing with heat transfer. Other similarities and differences are detailed in this work. Energy integration of a methanol plant is taken as a case study to test the efficacy of this methodology. Potential integration schemes are identified that would have been difficult to visualize without the help of the new graphical representation

  4. An Implentation Methodology for Integrated Resource Management in Urban Water Planning

    Science.gov (United States)

    Ebrahimi, G.; Thurm, B.; Klein, D. R.; Öberg, G.

    2014-12-01

    Urban water management requires innovative and integrative approaches to improve sustainability in cities keeping in touch with science progress. Integrated Resource Management (IRM) is one of these strategies and has been developed to integrate various natural and human resources. However, it is becoming increasingly clear that it is challenging to move from vision to implementation. The aim of this paper is to identify strengths and weaknesses of IRM and analyze if the approach might facilitate implementation of sustainability objectives in the water management field. A literature review was performed on peer-reviewed papers that were identified through Google Scholar search for the term 'Integrated Resource Management'. It was found that IRM has been used in a number of contexts such as urban planning, forestry, and management of waste and livestock. Significant implementation challenges are highlighted in the literature. Based on the lessons learned in many different fields, from forestry to communication sciences, important characteristics of IRM approach were found such as the need for adequate governance and strong leaderships, stakeholder's involvement, the learning process and the critical need of appropriate evaluation criteria. We conclude developing an implementation methodology and presenting several recommendations to implement IRM in urban management. While Integrated Water Resource Management (IWRM) is recognized as a fruitful approach to achieve sustainable water management, this study suggests that a shift toward Integrated Resource Management (IRM) can be beneficial as it is designed to facilitate consideration of the interrelationships between various natural and human resources.

  5. A quantitative flood risk analysis methodology for urban areas with integration of social research data

    Directory of Open Access Journals (Sweden)

    I. Escuder-Bueno

    2012-09-01

    Full Text Available Risk analysis has become a top priority for authorities and stakeholders in many European countries, with the aim of reducing flooding risk, considering the population's needs and improving risk awareness. Within this context, two methodological pieces have been developed in the period 2009–2011 within the SUFRI project (Sustainable Strategies of Urban Flood Risk Management with non-structural measures to cope with the residual risk, 2nd ERA-Net CRUE Funding Initiative. First, the "SUFRI Methodology for pluvial and river flooding risk assessment in urban areas to inform decision-making" provides a comprehensive and quantitative tool for flood risk analysis. Second, the "Methodology for investigation of risk awareness of the population concerned" presents the basis to estimate current risk from a social perspective and identify tendencies in the way floods are understood by citizens. Outcomes of both methods are integrated in this paper with the aim of informing decision making on non-structural protection measures. The results of two case studies are shown to illustrate practical applications of this developed approach. The main advantage of applying the methodology herein presented consists in providing a quantitative estimation of flooding risk before and after investing in non-structural risk mitigation measures. It can be of great interest for decision makers as it provides rational and solid information.

  6. A quantitative flood risk analysis methodology for urban areas with integration of social research data

    Science.gov (United States)

    Escuder-Bueno, I.; Castillo-Rodríguez, J. T.; Zechner, S.; Jöbstl, C.; Perales-Momparler, S.; Petaccia, G.

    2012-09-01

    Risk analysis has become a top priority for authorities and stakeholders in many European countries, with the aim of reducing flooding risk, considering the population's needs and improving risk awareness. Within this context, two methodological pieces have been developed in the period 2009-2011 within the SUFRI project (Sustainable Strategies of Urban Flood Risk Management with non-structural measures to cope with the residual risk, 2nd ERA-Net CRUE Funding Initiative). First, the "SUFRI Methodology for pluvial and river flooding risk assessment in urban areas to inform decision-making" provides a comprehensive and quantitative tool for flood risk analysis. Second, the "Methodology for investigation of risk awareness of the population concerned" presents the basis to estimate current risk from a social perspective and identify tendencies in the way floods are understood by citizens. Outcomes of both methods are integrated in this paper with the aim of informing decision making on non-structural protection measures. The results of two case studies are shown to illustrate practical applications of this developed approach. The main advantage of applying the methodology herein presented consists in providing a quantitative estimation of flooding risk before and after investing in non-structural risk mitigation measures. It can be of great interest for decision makers as it provides rational and solid information.

  7. Welfare Consequences of Omitting Beak Trimming in Barn Layers

    DEFF Research Database (Denmark)

    Riber, Anja Brinch; Hinrichsen, Lena Karina

    2017-01-01

    Beak trimming is used worldwide as a method of reducing the damage to feathers and skin caused by injurious pecking in laying hens. However, beak trimming also causes some welfare issues as trimming the beak results in pain and sensory loss. Due to this dilemma, there is an ongoing discussion...... in several European countries about whether to ban beak trimming. In this study, we investigated the welfare consequences of keeping layers with intact beaks and examined for links between injurious pecking damage and keel bone damage on an individual level. A study was conducted on 10 commercial farms...... housing laying hens in the barn system. Each farm participated with a flock of beak-trimmed hens (T) and a flock of non-trimmed (NT) hens that were visited around 32 and 62 weeks of age. During visits, the condition of plumage, skin, feet, and keel bone of 100 hens was assessed. Mortality was recorded...

  8. Measuring core inflation in India: An asymmetric trimmed mean approach

    Directory of Open Access Journals (Sweden)

    Naresh Kumar Sharma

    2015-12-01

    Full Text Available The paper seeks to obtain an optimal asymmetric trimmed mean-based core inflation measure in the class of trimmed mean measures when the distribution of price changes is leptokurtic and skewed to the right for any given period. Several estimators based on asymmetric trimmed mean approach are constructed and estimates generated by use of these estimators are evaluated on the basis of certain established empirical criteria. The paper also provides the method of trimmed mean expression “in terms of percentile score.” This study uses 69 monthly price indices which are constituent components of Wholesale Price Index for the period, April 1994 to April 2009, with 1993–1994 as the base year. Results of the study indicate that an optimally trimmed estimator is found when we trim 29.5% from the left-hand tail and 20.5% from the right-hand tail of the distribution of price changes.

  9. Methodologies for Wind Turbine and STATCOM Integration in Wind Power Plant Models for Harmonic Resonances Assessment

    DEFF Research Database (Denmark)

    Freijedo Fernandez, Francisco Daniel; Chaudhary, Sanjay Kumar; Guerrero, Josep M.

    2015-01-01

    -domain. As an alternative, a power based averaged modelling is also proposed. Type IV wind turbine harmonic signature and STATCOM active harmonic mitigation are considered for the simulation case studies. Simulation results provide a good insight of the features and limitations of the proposed methodologies.......This paper approaches modelling methodologies for integration of wind turbines and STATCOM in harmonic resonance studies. Firstly, an admittance equivalent model representing the harmonic signature of grid connected voltage source converters is provided. A simplified type IV wind turbine modelling...... is then straightforward. This linear modelling is suitable to represent the wind turbine in the range of frequencies at which harmonic interactions are likely. Even the admittance method is suitable both for frequency and time domain studies, some limitations arise in practice when implementing it in the time...

  10. Methodology for the Integration of Safety in the Optimization of the Advanced Reactors Design

    International Nuclear Information System (INIS)

    Grinblat, P.; Schlamp, M.; Brasnarof, D.; Gimenez, M.

    2003-01-01

    In this work a new methodology has been developed and implemented for taking into account the safety levels of the reactor in a design optimization process, by using Design Maps.They represent a new technique for comparing critical variables in case an accidental sequenced happened, with limit values set by the design criteria.So a good balance is achieved, without allowing the economic performance search to cause a too risky reactor, and guaranteeing the competitiveness of it in spite of the safety costs.Up to the moment, there is no design tool able to accomplish this task in an integrated way.A computational tool based on this methodology has been implemented.These tool specially programmed routines allow carrying out the mentioned tasks

  11. Applied methodology for replacement pipe arcs in integral pipelines TE 'Oslomej'

    Directory of Open Access Journals (Sweden)

    Temelkoska Bratica K.

    2016-01-01

    Full Text Available The integral pipelines in thermal power plants present a linear spatial bearing construction with high operating parameters, complex static and dynamic load. The integral pipelines along its entire length are hanging on construction spring hangers from the boiler building, where the boiler is placed, next to the machine hall where the turbine is placed. Therefore, it is important to monitor the condition and to remove any possible defects from the applied methods. This paper describes the methodology of replacement of the pipe arch on one of the integral pipelines-the line for hot superheated steam. In addition, in this paper are given the method methods that led to this methodology for testing and evaluation of the condition of the pipe arch material that had been in exploitation and the new pipe arch that will be embedded. Furthermore the approach, the technology of replacement, anchoring of the steam line, technology of welding etc., as well as the preparation of the final design of constructed condition are also covered in this paper.

  12. Methodology of Integration for Competitive Technical Intelligence with Blue Ocean Strategy: Application to an exotic fruit

    Directory of Open Access Journals (Sweden)

    Marisela Rodríguez Salvador

    2011-12-01

    Full Text Available This article presents a new methodology that integrates Competitive Technical Intelligence with Blue Ocean Strategy. We explore new business niches taking advantage of the synergy that both areas offer, developing a model based on cyclic interactions through a process developed in two stages: Understanding opportunity that arise from idea formulation to decision making and strategic development. The validity of our approach (first stage was observed in the evaluation of an exotic fruit, Anacardium Occidentale, in the South of the State of Veracruz, Mexico with the support of the university ITESM, Campus Monterrey. We identified critical factors for success, opportunities and threats. Results confirm the attractiveness of this crop.

  13. Integrated management of operations in Santos Basin: methodology applied to a new philosophy of operations

    Energy Technology Data Exchange (ETDEWEB)

    Pereira, Leandro Leonardo; Lima, Claudio Benevenuto de Campos [Petroleo Brasileiro S.A. (PETROBRAS), Rio de Janeiro, RJ (Brazil); Derenzi Neto, Dario [Accenture, Rio de Janeiro, RJ (Brazil); Pinto, Vladimir Steffen [Soda IT, Rio de Janeiro, RJ (Brazil); Lima, Gilson Brito Alves [Universidade Federal Fluminense (UFF), Niteroi, RJ (Brazil)

    2012-07-01

    The objective of this paper is to present the methodology used to develop the Integrated Management of Operations (GIOp) project in Santos Basin Operational Unit (UO-BS) in the South-Southeast Exploration and Production area of PETROBRAS. The following text describes how the activities were carried out to gather improvements opportunities and to design To-Be processes, considering the challenging environment of the Santos Basin in the coming years. At the end of more than 12 months of work, more than 50 processes and sub-processes were redesigned, involving a multidisciplinary team in the areas of operations, maintenance, safety, health and environment, flow assurance, wells, reservoirs and planning. (author)

  14. Stable isogeometric analysis of trimmed geometries

    Science.gov (United States)

    Marussig, Benjamin; Zechner, Jürgen; Beer, Gernot; Fries, Thomas-Peter

    2017-04-01

    We explore extended B-splines as a stable basis for isogeometric analysis with trimmed parameter spaces. The stabilization is accomplished by an appropriate substitution of B-splines that may lead to ill-conditioned system matrices. The construction for non-uniform knot vectors is presented. The properties of extended B-splines are examined in the context of interpolation, potential, and linear elasticity problems and excellent results are attained. The analysis is performed by an isogeometric boundary element formulation using collocation. It is argued that extended B-splines provide a flexible and simple stabilization scheme which ideally suits the isogeometric paradigm.

  15. Internal trim coils for CBA superconducting magnets

    International Nuclear Information System (INIS)

    Thompson, P.A.; Aronson, S.; Cottingham, J.G.; Garber, M.; Hahn, H.; Sampson, W.B.

    1983-01-01

    In order to correct iron saturation effects and shape the beam working line, superconducting trim coils have been constructed, which operate inside the main coils. Detailed studies of mechanical properties, quench behavior, fields produced, and hysteresis have lead to the production of accelerator-quality coils generating the required-strength harmonics up to cos (7theta). These are routinely installed in CBA main magnets and operate at 80% of short sample with negligible training in an ambient field of more than 5.3T

  16. UPCaD: A Methodology of Integration Between Ontology-Based Context-Awareness Modeling and Relational Domain Data

    Directory of Open Access Journals (Sweden)

    Vinícius Maran

    2018-01-01

    Full Text Available Context-awareness is a key feature for ubiquitous computing scenarios applications. Currently, technologies and methodologies have been proposed for the integration of context-awareness concepts in intelligent information systems to adapt them to the execution of services, user interfaces and data retrieval. Recent research proposed conceptual modeling alternatives to the integration of the domain modeling in RDBMS and context-awareness modeling. The research described using highly expressiveness ontologies. The present work describes the UPCaD (Unified Process for Integration between Context-Awareness and Domain methodology, which is composed of formalisms and processes to guide the data integration considering RDBMS and context modeling. The methodology was evaluated in a virtual learning environment application. The evaluation shows the possibility to use a highly expressive context ontology to filter the relational data query and discusses the main contributions of the methodology compared with recent approaches.

  17. The application of life cycle assessment to integrated solid waste management. Pt. 1: Methodology

    Energy Technology Data Exchange (ETDEWEB)

    Clift, R.; Doig, A.; Finnveden, G.

    2000-07-01

    Integrated Waste Management is one of the holistic approaches to environmental and resource management which are emerging from applying the concept of sustainable development. Assessment of waste management options requires application of Life Cycle Assessment (LCA). This paper summarizes the methodology for applying LCA to Integrated Waste Management of Municipal Solid Wastes (MSW) developed for and now used by the UK Environment Agency, including recent developments in international fora. Particular attention is devoted to system definition leading to rational and clear compilation of the Life Cycle Inventory, with appropriate 'credit' for recovering materials and/or energy from the waste. LCA of waste management is best seen as a way of structuring information to help decision processes. (Author)

  18. Measurements of integrated components' parameters versus irradiation doses gamma radiation (60Co) dosimetry-methodology-tests

    International Nuclear Information System (INIS)

    Fuan, J.

    1991-01-01

    This paper describes the methodology used for the irradiation of the integrated components and the measurements of their parameters, using Quality Insurance of dosimetry: - Measurement of the integrated dose using the competences of the Laboratoire Central des Industries Electriques (LCIE): - Measurement of irradiation dose versus source/component distance, using a calibrated equipment. - Use of ALANINE dosimeters, placed on the support of the irradiated components. - Assembly and polarization of components during the irradiations. Selection of the irradiator. - Measurement of the irradiated components's parameters, using the competences of the societies: - GenRad: GR130 tests equipement placed in the DEIN/SIR-CEN SACLAY. - Laboratoire Central des Industries Electriques (LCIE): GR125 tests equipment and this associated programmes test [fr

  19. TRIM45, a novel human RBCC/TRIM protein, inhibits transcriptional activities of ElK-1 and AP-1

    International Nuclear Information System (INIS)

    Wang Yuequn; Li Yongqing; Qi Xinzhu; Yuan Wuzhou; Ai Jianping; Zhu Chuanbing; Cao Lei; Yang Hong; Liu Fang; Wu Xiushan; Liu Mingyao

    2004-01-01

    The tripartite motif (TRIM) proteins play important roles in a variety of cellular functions including cell proliferation, differentiation, development, oncogenesis, and apoptosis. In this study, we report the identification and characterization of the human tripartite motif-containing protein 45 (TRIM45), a novel member of the TRIM family, from a human embryonic heart cDNA library. TRIM45 has a predicted 580 amino acid open reading frame, encoding a putative 64-kDa protein. The N-terminal region harbors a RING finger, two B-boxes, and a predicted α-helical coiled-coil domain, which together form the RBCC/TRIM motif found in a large family of proteins, whereas the C-terminal region contains a filamin-type immunoglobulin (IG-FLMN) domain. Northern blot analysis indicates that TRIM45 is expressed in a variety of human adult and embryonic tissues. In the cell, TRIM45 protein is expressed both in cytoplasm and in cell nucleus. Overexpression of TRIM45 in COS-7 cells inhibits the transcriptional activities of ElK-1 and AP-1. These results suggest that TRIM45 may act as a new transcriptional repressor in mitogen-activated protein kinase signaling pathway

  20. Methodologies of health impact assessment as part of an integrated approach to reduce effects of air pollution

    OpenAIRE

    Aunan, Kristin; Seip, Hans Martin

    1995-01-01

    Quantification of average frequencies of health effects on a population level is an essential part of an integrated assessment of pollution effects. Epidemiological studies seem to provide the best basis for such estimates. This paper gives an introduction to a methodology for health impact assessment. It also gives results from some selected parts of a case-study in Hungary. This study is aimed at testing and improving the methodology for integrated assessment and focuses on energy productio...

  1. Vedic division methodology for high-speed very large scale integration applications

    Directory of Open Access Journals (Sweden)

    Prabir Saha

    2014-02-01

    Full Text Available Transistor level implementation of division methodology using ancient Vedic mathematics is reported in this Letter. The potentiality of the ‘Dhvajanka (on top of the flag’ formula was adopted from Vedic mathematics to implement such type of divider for practical very large scale integration applications. The division methodology was implemented through half of the divisor bit instead of the actual divisor, subtraction and little multiplication. Propagation delay and dynamic power consumption of divider circuitry were minimised significantly by stage reduction through Vedic division methodology. The functionality of the division algorithm was checked and performance parameters like propagation delay and dynamic power consumption were calculated through spice spectre with 90 nm complementary metal oxide semiconductor technology. The propagation delay of the resulted (32 ÷ 16 bit divider circuitry was only ∼300 ns and consumed ∼32.5 mW power for a layout area of 17.39 mm^2. Combination of Boolean arithmetic along with ancient Vedic mathematics, substantial amount of iterations were reduced resulted as ∼47, ∼38, 34% reduction in delay and ∼34, ∼21, ∼18% reduction in power were investigated compared with the mostly used (e.g. digit-recurrence, Newton–Raphson, Goldschmidt architectures.

  2. Analysis of cold leg LOCA with failed HPSI by means of integrated safety assessment methodology

    International Nuclear Information System (INIS)

    Gonzalez-Cadelo, J.; Queral, C.; Montero-Mayorga, J.

    2014-01-01

    Highlights: • Results of ISA for considered sequences endorse EOPs guidance in an original way. • ISA allows to obtain accurate available times for accident management actions. • RCP-trip adequacy and available time for beginning depressurization are evaluated. • ISA minimizes the necessity of expert judgment to perform safety assessment. - Abstract: The integrated safety assessment (ISA) methodology, developed by the Spanish Nuclear Safety Council (CSN), has been applied to a thermal–hydraulic analysis of cold leg LOCA sequences with unavailable High Pressure Injection System in a Westinghouse 3-loop PWR. This analysis has been performed with TRACE 5.0 patch 1 code. ISA methodology allows obtaining the Damage Domain (the region of space of parameters where a safety limit is exceeded) as a function of uncertain parameters (break area) and operator actuation times, and provides to the analyst useful information about the impact of these uncertain parameters in safety concerns. In this work two main issues have been analyzed: the effect of reactor coolant pump trip and the available time for beginning of secondary-side depressurization. The main conclusions are that present Emergency Operating Procedures (EOPs) are adequate for managing this kind of sequences and the ISA methodology is able to take into account time delays and parameter uncertainties

  3. A New Integrated Threshold Selection Methodology for Spatial Forecast Verification of Extreme Events

    Science.gov (United States)

    Kholodovsky, V.

    2017-12-01

    Extreme weather and climate events such as heavy precipitation, heat waves and strong winds can cause extensive damage to the society in terms of human lives and financial losses. As climate changes, it is important to understand how extreme weather events may change as a result. Climate and statistical models are often independently used to model those phenomena. To better assess performance of the climate models, a variety of spatial forecast verification methods have been developed. However, spatial verification metrics that are widely used in comparing mean states, in most cases, do not have an adequate theoretical justification to benchmark extreme weather events. We proposed a new integrated threshold selection methodology for spatial forecast verification of extreme events that couples existing pattern recognition indices with high threshold choices. This integrated approach has three main steps: 1) dimension reduction; 2) geometric domain mapping; and 3) thresholds clustering. We apply this approach to an observed precipitation dataset over CONUS. The results are evaluated by displaying threshold distribution seasonally, monthly and annually. The method offers user the flexibility of selecting a high threshold that is linked to desired geometrical properties. The proposed high threshold methodology could either complement existing spatial verification methods, where threshold selection is arbitrary, or be directly applicable in extreme value theory.

  4. [Problems of world outlook and methodology of science integration in biological studies].

    Science.gov (United States)

    Khododova, Iu D

    1981-01-01

    Problems of worldoutlook and methodology of the natural-science knowledge are considered basing on the analysis of tendencies in the development of the membrane theory of cell processes and the use of principles of biological membrane functioning when solving some scientific and applied problems pertaining to different branches of chemistry and biology. The notion scientific knowledge integration is defined as interpenetration of approaches, methods and ideas of different branches of knowledge and enrichment on this basis of their content resulting in knowledge augmentation in each field taken separately. These processes are accompanied by appearance of new branches of knowledge - sciences "on junction" and their subsequent differentiations. The analysis of some gnoseological situations shows that integration of sciences contributes to coordination and some agreement of thinking styles of different specialists, puts forward keen personality of a scientist demanding, in particular, his high professional mobility. Problems of scientific activity organization are considered, which involve social sciences into the integration processes. The role of philosophy in the integration processes is emphasized.

  5. An integrated methodology to evaluate a spent nuclear fuel storage system

    International Nuclear Information System (INIS)

    Yoon, Jeong Hyoun

    2008-02-01

    This study introduced a methodology that can be applied for development of a dry storage system for spent nuclear fuels. It consisted of several design activities that includes development of a simplified program to analyze the amount of spent nuclear fuels from reflecting the practical situation in spent nuclear fuel management and a simplified program to evaluate the cost of 4 types of representing storage system to choose the most competitive option considering economic factor. As verification of the implementation of the reference module to practical purpose, a simplified thermal analysis code was suggested that can see fulfillment of limitation of temperature in long term storage and oxidation analysis. From the thermal related results, the reference module can accommodate full range of PHWR spent nuclear fuels and significant portion of PWR ones too. From the results, the reference storage system can be concluded that has fulfilled the important requirements in terms of long term integrity and radiological safety. Also for the purpose of solving scattered radiation along with deep penetration problems in cooling storage system, small but efficient design alternation was suggested together with its efficiency that can reduce scattered radiation by 1/3 from the original design. Along with the countermeasure for the shielding problem, in consideration of PWR spent nuclear fuels, simplified criticality analysis methodology retaining conservativeness was proposed. The results show the reference module is efficient low enrichment PWR spent nuclear fuel and even relatively high enrichment fuels too if burnup credit is taken. As conclusive remark, the methodology is simple but efficient to plan a concept design of convective cooling type of spent nuclear fuels storage. It can be also concluded that the methodology derived in this study and the reference module has feasibility in practical implementation to mitigate the current complex situation in spent fuel

  6. Design methodology for integrated downstream separation systems in an ethanol biorefinery

    Science.gov (United States)

    Mohammadzadeh Rohani, Navid

    and obtaining energy security. On the other hand, Process Integration (PI) as defined by Natural Resource Canada as the combination of activities which aim at improving process systems, their unit operations and their interactions in order to maximize the efficiency of using water, energy and raw materials can also help biorefineries lower their energy consumptions and improve their economics. Energy integration techniques such as pinch analysis adopted by different industries over the years have ensured using heat sources within a plant to supply the demand internally and decrease the external utility consumption. Therefore, adopting energy integration can be one of the ways biorefinery technology owners can consider in their process development as well as their business model in order to improve their overall economics. The objective of this thesis is to propose a methodology for designing integrated downstream separation in a biorefinery. This methodology is tested in an ethanol biorefinery case study. Several alternative separation techniques are evaluated in their energy consumption and economics in three different scenarios; stand-alone without energy integration, stand-alone with internal energy integration and integrated-with Kraft. The energy consumptions and capital costs of separation techniques are assessed in each scenario and the cost and benefit of integration are determined and finally the best alternative is found through techno-economic metrics. Another advantage of this methodology is the use of a graphical tool which provides insights on decreasing energy consumption by modifying the process condition. The pivot point of this work is the use of a novel energy integration method called Bridge analysis. This systematic method which originally is intended for retrofit situation is used here for integration with Kraft process. Integration potentials are identified through this method and savings are presented for each design. In stand-alone with

  7. D Integrated Methodologies for the Documentation and the Virtual Reconstruction of AN Archaeological Site

    Science.gov (United States)

    Balletti, C.; Guerra, F.; Scocca, V.; Gottardi, C.

    2015-02-01

    Highly accurate documentation and 3D reconstructions are fundamental for analyses and further interpretations in archaeology. In the last years the integrated digital survey (ground-based survey methods and UAV photogrammetry) has confirmed its main role in the documentation and comprehension of excavation contexts, thanks to instrumental and methodological development concerning the on site data acquisition. The specific aim of the project, reported in this paper and realized by the Laboratory of Photogrammetry of the IUAV University of Venice, is to check different acquisition systems and their effectiveness test, considering each methodology individually or integrated. This research focuses on the awareness that the integration of different survey's methodologies can as a matter of fact increase the representative efficacy of the final representations; these are based on a wider and verified set of georeferenced metric data. Particularly the methods' integration allows reducing or neutralizing issues related to composite and complex objects' survey, since the most appropriate tools and techniques can be chosen considering the characteristics of each part of an archaeological site (i.e. urban structures, architectural monuments, small findings). This paper describes the experience in several sites of the municipality of Sepino (Molise, Italy), where the 3d digital acquisition of cities and structure of monuments, sometimes hard to reach, was realized using active and passive techniques (rage-based and image based methods). This acquisition was planned in order to obtain not only the basic support for interpretation analysis, but also to achieve models of the actual state of conservation of the site on which some reconstructive hypotheses can be based on. Laser scanning data were merged with Structure from Motion techniques' clouds into the same reference system, given by a topographical and GPS survey. These 3d models are not only the final results of the metric

  8. Performance of trim coils made by a novel method

    International Nuclear Information System (INIS)

    Wanderer, P.; Anerella, M.; Cottingham, J.; Ganetis, G.; Garber, M.; Ghosh, A.; Goodzeit, C.; Greene, A.; Gupta, R.; Herrera, J.; Kahn, S.; Kelly, E.; Meade, A.; Morgan, G.; Muratore, J.; Prodell, A.; Rehak, M.; Rohrer, E.P.; Sampson, W.; Shutt, R.; Skaritka, J.; Thompson, P.; Willen, E.

    1991-01-01

    A precision, automated method of manufacturing trim coils based on printed circuit technology has been developed. Excellent quench performance and increased radiation resistance have been achieved in recently-tested models of sextupole trim coils developed for operation inside 40 mm-aperture SSC Main Collider dipoles. 6 refs., 2 figs

  9. Surveillance for Intracellular Antibody by Cytosolic Fc Receptor TRIM21

    Directory of Open Access Journals (Sweden)

    William A. McEwan

    2016-11-01

    Full Text Available TRIM21 has emerged as an atypical Fc receptor that is broadly conserved and widely expressed in the cytoplasm of mammalian cells. Viruses that traffic surface-bound antibodies into the cell during infection recruit TRIM21 via a high affinity interaction between Fc and TRIM21 PRYSPRY domain. Following binding of intracellular antibody, TRIM21 acts as both antiviral effector and sensor for innate immune signalling. These activities serve to reduce viral replication by orders of magnitude in vitro and contribute to host survival during in vivo infection. Neutralization occurs rapidly after detection and requires the activity of the ubiquitin-proteasome system. The microbial targets of this arm of intracellular immunity are still being identified: TRIM21 activity has been reported following infection by several non-enveloped viruses and intracellular bacteria. These findings extend the sphere of influence of antibodies to the intracellular domain and have broad implications for immunity. TRIM21 has been implicated in the chronic auto-immune condition systemic lupus erythematosus and is itself an auto-antigen in Sjögren’s syndrome. This review summarises our current understanding of TRIM21’s role as a cytosolic Fc receptor and briefly discusses pathological circumstances where intracellular antibodies have been described, or are hypothesized to occur, and may benefit from further investigations of the role of TRIM21.

  10. Improvement of Springback Predictability after forming and trimming

    NARCIS (Netherlands)

    Avetisyan, Marianna; Meinders, Vincent T.; Huetink, Han; Storen, S.

    2004-01-01

    When a sheet metal forming operation, such as deep drawing, is followed by a trimming operation the numerical springback after trimming is influenced by physical parameters and loss of product stiffness due to cutting off the material. Moreover, it is affected by the finite element mesh disturbance

  11. Role of TRIM33 in Wnt signaling during mesendoderm differentiation.

    Science.gov (United States)

    Xia, Xiaojie; Zuo, Feifei; Luo, Maoguo; Sun, Ye; Bai, Jianbo; Xi, Qiaoran

    2017-10-01

    Tripartite motif 33 (TRIM33), a member of the transcription intermediate factor 1 (TIF1) family of transcription cofactors, mediates transforming growth factor-beta (TGF-β) signaling through its PHD-Bromo cassette in mesendoderm differentiation during early mouse embryonic development. However, the role of the TRIM33 RING domain in embryonic differentiation is less clear. Here, we report that TRIM33 mediates Wnt signaling by directly regulating the expression of a specific subset of Wnt target genes, and this action is independent of its RING domain. We show that TRIM33 interacts with β-catenin, a central player in Wnt signaling in mouse embryonic stem cells (mESCs). In contrast to previous reports in cancer cell lines, the RING domain does not appear to function as the E3 ligase for β-catenin, since neither knockout nor overexpression of TRIM33 had an effect on β-catenin protein levels in mESCs. Furthermore, we show that although TRIM33 seems to be dispensable for Wnt signaling through a reporter assay, loss of TRIM33 significantly impairs the expression of a subset of Wnt target genes, including Mixl1, in a Wnt signaling-dependent manner. Together, our results indicate that TRIM33 regulates Wnt signaling independent of the E3 ligase activity of its RING domain for β-catenin in mESCs.

  12. The Socio-ecological Fit of Human Responses to Environmental Degradation: An Integrated Assessment Methodology.

    Science.gov (United States)

    Briassoulis, Helen

    2015-12-01

    The scientific and policy interest in the human responses to environmental degradation usually focuses on responses sensu stricto and 'best practices' that potentially abate degradation in affected areas. The transfer of individual, discrete instruments and 'best practices' to different contexts is challenging, however, because socio-ecological systems are complex and environmental degradation is contextual and contingent. To sensibly assess the effectiveness of formal and informal interventions to combat environmental degradation, the paper proposes an integrative, non-reductionist analytic, the 'response assemblage', for the study of 'responses-in-context,' i.e., products of human decisions to utilize environmental resources to satisfy human needs in socio-ecological systems. Response assemblages are defined as geographically and historically unique, provisional, open, territorial wholes, complex compositions emerging from processes of assembling biophysical and human components, including responses sensu stricto, from affected focal and other socio-ecological systems, to serve human goals, one of which may be combatting environmental degradation. The degree of match among the components, called the socio-ecological fit of the response assemblage, indicates how effectively their contextual and contingent interactions maintain the socio-ecological resilience, promote sustainable development, and secure the continuous provision of ecosystem services in a focal socio-ecological system. The paper presents a conceptual approach to the analysis of the socio-ecological fit of response assemblages and details an integrated assessment methodology synthesizing the resilience, assemblage, and 'problem of fit' literature. Lastly, it summarizes the novelty, value, and policy relevance of conceptualizing human responses as response assemblages and of the integrated assessment methodology, reconsiders 'best practices' and suggests selected future research directions.

  13. The Socio-ecological Fit of Human Responses to Environmental Degradation: An Integrated Assessment Methodology

    Science.gov (United States)

    Briassoulis, Helen

    2015-12-01

    The scientific and policy interest in the human responses to environmental degradation usually focuses on responses sensu stricto and `best practices' that potentially abate degradation in affected areas. The transfer of individual, discrete instruments and `best practices' to different contexts is challenging, however, because socio-ecological systems are complex and environmental degradation is contextual and contingent. To sensibly assess the effectiveness of formal and informal interventions to combat environmental degradation, the paper proposes an integrative, non-reductionist analytic, the `response assemblage', for the study of `responses-in-context,' i.e., products of human decisions to utilize environmental resources to satisfy human needs in socio-ecological systems. Response assemblages are defined as geographically and historically unique, provisional, open, territorial wholes, complex compositions emerging from processes of assembling biophysical and human components, including responses sensu stricto, from affected focal and other socio-ecological systems, to serve human goals, one of which may be combatting environmental degradation. The degree of match among the components, called the socio- ecological fit of the response assemblage, indicates how effectively their contextual and contingent interactions maintain the socio-ecological resilience, promote sustainable development, and secure the continuous provision of ecosystem services in a focal socio-ecological system. The paper presents a conceptual approach to the analysis of the socio-ecological fit of response assemblages and details an integrated assessment methodology synthesizing the resilience, assemblage, and `problem of fit' literature. Lastly, it summarizes the novelty, value, and policy relevance of conceptualizing human responses as response assemblages and of the integrated assessment methodology, reconsiders `best practices' and suggests selected future research directions.

  14. Methodology of structural integrity assesment of CANDU-6 NPP fuel channels

    International Nuclear Information System (INIS)

    Radu, Vasile

    2004-01-01

    The paper describes the methodology of assessing the structural integrity in the CANDU-6 fuel channels making use of alternative methods of evaluation. An evaluation of the structural integrity of a CANDU-6 pressure tube made of Zr-2,5%Nb presenting both sharp and blunted defects is done. These analyses are made in compliance with the Canadian guide 'Pressure Tubes Fitness-for-service', and other two Recognizing procedures internationally adopted: the British procedure R6/Rev.4 and the American procedure API 579. Previously, the data base containing the data on materials property as well as the heat and dynamical loads in normal operation in CANDU-6 pressure tubes was established. Obtaining complete diagrams for structural integrity of pressure tubes with sharp and blunted defects in conditions of normal operation and long-term irradiation is the next step of the methodology to be developed. Modelling sharp and blunted defects on the inner side of pressure tubes, which can occur in normal reactor operating conditions is achieved by means of capabilities of pre-processing of two finite element analysis codes namely FEA-Crack and FEA-Flaw. The second part of the work deals with the analyses by finite element method of the fracture mechanics by means of the FEA-Crack code and with the evaluation of sharp and blunted defects by FAD diagrams in compliance with the British procedure R6/Rev.4. For typical models of blunted defects and thermo-mechanical loads specific to normal operation finite element analyses by FEA-Flaw codes were performed. Then FAD-iDHC diagrams were constructed to evaluate the initiation of the slow cracking under hydrogen/deuterium absorption, the known phenomenon of delayed hydride cracking (DHC)

  15. Safety studies on Korean fusion DEMO plant using integrated safety assessment methodology

    International Nuclear Information System (INIS)

    Oh, Kyemin; Kang, Myoung-suk; Heo, Gyunyoung; Kim, Hyoung-chan

    2014-01-01

    Highlights: •The purpose of this paper is to suggest methodology that can investigate safety issues and provides a case study for Korean fusion DEMO plant. •The concepts of integrated safety assessment methodology (ISAM) that can be applied in addressing regulatory requirements and recognizing safety issues for K-DEMO were emphasized. •Phenomena identification and ranking table (PIRT) was proposed. It can recognize vulnerabilities of systems and identify the gaps in technical areas requiring additional researches. •This work is expected to contribute on the conceptual design of safety features for K-DEMO to design engineers and the guidance for regulatory requirements to licensers. -- Abstract: The purpose of this paper is to suggest methodology that can investigate safety issues and provides a case study for Korean fusion DEMO plant (K-DEMO) as a part of R and D program through the National Fusion Research Institute of Korea. Even though nuclear regulation and licensing framework is well setup due to the operating and design experience of Pressurized Water Reactors (PWRs) since 1970s, the regulatory authority of South Korea has concerns on the challenge of facing new nuclear facilities including K-DEMO due to the differences in systems, materials, and inherent safety feature from conventional PWRs. Even though the follow-up of the ITER license process facilitates to deal with significant safety issues of fusion facilities, a licensee as well as a licenser should identify the gaps between ITER and DEMO in terms of safety issues. First we reviewed the methods of conducting safety analysis for unprecedented nuclear facilities such as Generation IV reactors, particularly very high temperature reactor (VHTR), which is called as integrated safety assessment methodology (ISAM). Second, the analysis for the conceptual design of K-DEMO on the basis of ISAM was conducted. The ISAM consists of five analytical tools to develop the safety requirements from licensee

  16. Safety studies on Korean fusion DEMO plant using integrated safety assessment methodology

    Energy Technology Data Exchange (ETDEWEB)

    Oh, Kyemin; Kang, Myoung-suk [Kyung Hee University, Youngin-si, Gyeonggi-do 446-701 (Korea, Republic of); Heo, Gyunyoung, E-mail: gheo@khu.ac.kr [Kyung Hee University, Youngin-si, Gyeonggi-do 446-701 (Korea, Republic of); Kim, Hyoung-chan [National Fusion Research Institute, Daejeon-si 305-333 (Korea, Republic of)

    2014-10-15

    Highlights: •The purpose of this paper is to suggest methodology that can investigate safety issues and provides a case study for Korean fusion DEMO plant. •The concepts of integrated safety assessment methodology (ISAM) that can be applied in addressing regulatory requirements and recognizing safety issues for K-DEMO were emphasized. •Phenomena identification and ranking table (PIRT) was proposed. It can recognize vulnerabilities of systems and identify the gaps in technical areas requiring additional researches. •This work is expected to contribute on the conceptual design of safety features for K-DEMO to design engineers and the guidance for regulatory requirements to licensers. -- Abstract: The purpose of this paper is to suggest methodology that can investigate safety issues and provides a case study for Korean fusion DEMO plant (K-DEMO) as a part of R and D program through the National Fusion Research Institute of Korea. Even though nuclear regulation and licensing framework is well setup due to the operating and design experience of Pressurized Water Reactors (PWRs) since 1970s, the regulatory authority of South Korea has concerns on the challenge of facing new nuclear facilities including K-DEMO due to the differences in systems, materials, and inherent safety feature from conventional PWRs. Even though the follow-up of the ITER license process facilitates to deal with significant safety issues of fusion facilities, a licensee as well as a licenser should identify the gaps between ITER and DEMO in terms of safety issues. First we reviewed the methods of conducting safety analysis for unprecedented nuclear facilities such as Generation IV reactors, particularly very high temperature reactor (VHTR), which is called as integrated safety assessment methodology (ISAM). Second, the analysis for the conceptual design of K-DEMO on the basis of ISAM was conducted. The ISAM consists of five analytical tools to develop the safety requirements from licensee

  17. Assessment of gamma irradiation heating and damage in miniature neutron source reactor vessel using computational methods and SRIM - TRIM code

    International Nuclear Information System (INIS)

    Appiah-Ofori, F. F.

    2014-07-01

    its location within the vessel. The Numerical Algorithms were simulated using MATLAB Code developed for solution by Gaussian Elimination method. The methodology also employed SRIM - TRIM Code, to determine the number of defects produced by a primary knock-on atom (pka). In the SRIM - TRIM code, Detailed Calculation with Full Damage Cascades option was selected as the damage type with Tables 3.1 and 3.2 as the Ion and Target Data and input parameters. Cobalt ion of energy 5000 keV was directed to the target atom, AI, to interact with the lattice atoms (500) which produced 14052 vacancies and 14783 interstitials as microscopic defects. The vessel absorbed energy of 1.09 MeV and lattice atoms of the vessel (AI) were shifted or displaced from their site by 0.0207 times. DPA is a measure of amount of radiation damage in a solid induced by gamma irradiation. The Analytical and Numerical (CVFDM) solutions obtained from the models developed were far below the value of the melting point 933.47 K while the result obtained from the thermal stresses were also far below the yield stress 480 MPa (properties of the vessel) indicated that the induced maximum effective thermal stress due to the absorption of gamma ray of energy 5.0 MeV originating from the reactor core had relatively no effect or can posed no danger on the structural integrity of GHARR-I reactor vessel during operation. (au)

  18. Study of the methodology for sensitivity calculations of fast reactors integral parameters

    International Nuclear Information System (INIS)

    Renke, C.A.C.

    1981-06-01

    A study of the methodology for sensitivity calculations of integral parameters of fast reactors for the adjustment of multigroup cross sections is presented. A description of several existent methods and theories is given, with special emphasis being regarded to variational perturbation theory, integrant of the sensitivity code VARI-1D used in this work. Two calculational systems are defined and a set of procedures and criteria is structured gathering the necessary conditions for the determination of the sensitivity coefficients. These coefficients are then computed by both the direct method and the variational perturbation theory. A reasonable number of sensitivity coefficients are computed and analyzed for three fast critical assemblies, covering a range of special interest of the spectrum. These coefficients are determined for severa integral parameters, for the capture and fission cross sections of the U-238 and Pu-239, covering all the energy up to 14.5 MeV. The nuclear data used were obtained the CARNAVAL II calculational system of the Instituto de Engenharia Nuclear. An optimization for sensitivity computations in a chainned sequence of procedures is made, yielding the sensitivities in the energy macrogroups as the final stage. (Author) [pt

  19. A hybrid design methodology for structuring an Integrated Environmental Management System (IEMS) for shipping business.

    Science.gov (United States)

    Celik, Metin

    2009-03-01

    The International Safety Management (ISM) Code defines a broad framework for the safe management and operation of merchant ships, maintaining high standards of safety and environmental protection. On the other hand, ISO 14001:2004 provides a generic, worldwide environmental management standard that has been utilized by several industries. Both the ISM Code and ISO 14001:2004 have the practical goal of establishing a sustainable Integrated Environmental Management System (IEMS) for shipping businesses. This paper presents a hybrid design methodology that shows how requirements from both standards can be combined into a single execution scheme. Specifically, the Analytic Hierarchy Process (AHP) and Fuzzy Axiomatic Design (FAD) are used to structure an IEMS for ship management companies. This research provides decision aid to maritime executives in order to enhance the environmental performance in the shipping industry.

  20. Methodology for Supply Chain Integration: A Case Study in the Artisan Industry of Footwear

    Directory of Open Access Journals (Sweden)

    Jorge Raúl Pérez-Gallardo

    2014-01-01

    Full Text Available The supply chain is a major issue in a global market. The efficient relationship between supplier-producer-retailer conforms the perfect combination to achieve a high level of competitiveness according to the needs of increasingly demanding and changing markets. The difficulty of synchronizing the members within the SC is related to the inherent uncertain factors. This paper proposes a methodology for integrating the supply chain that can be applied in any type of business. To demonstrate its relevance, a case study is performed at a handmade shoe company. An improved demand forecasting, an optimal balanced production line, a proper inventory management of raw materials, and an efficient calculation of the delivery time to the customer represent some of the main results.

  1. Trimming and procrastination as inversion techniques

    Science.gov (United States)

    Backus, George E.

    1996-12-01

    By examining the processes of truncating and approximating the model space (trimming it), and by committing to neither the objectivist nor the subjectivist interpretation of probability (procrastinating), we construct a formal scheme for solving linear and non-linear geophysical inverse problems. The necessary prior information about the correct model xE can be either a collection of inequalities or a probability measure describing where xE was likely to be in the model space X before the data vector y0 was measured. The results of the inversion are (1) a vector z0 that estimates some numerical properties zE of xE; (2) an estimate of the error δz = z0 - zE. As y0 is finite dimensional, so is z0, and hence in principle inversion cannot describe all of xE. The error δz is studied under successively more specialized assumptions about the inverse problem, culminating in a complete analysis of the linear inverse problem with a prior quadratic bound on xE. Our formalism appears to encompass and provide error estimates for many of the inversion schemes current in geomagnetism, and would be equally applicable in geodesy and seismology if adequate prior information were available there. As an idealized example we study the magnetic field at the core-mantle boundary, using satellite measurements of field elements at sites assumed to be almost uniformly distributed on a single spherical surface. Magnetospheric currents are neglected and the crustal field is idealized as a random process with rotationally invariant statistics. We find that an appropriate data compression diagonalizes the variance matrix of the crustal signal and permits an analytic trimming of the idealized problem.

  2. Evaluating perceptual integration: uniting response-time- and accuracy-based methodologies.

    Science.gov (United States)

    Eidels, Ami; Townsend, James T; Hughes, Howard C; Perry, Lacey A

    2015-02-01

    This investigation brings together a response-time system identification methodology (e.g., Townsend & Wenger Psychonomic Bulletin & Review 11, 391-418, 2004a) and an accuracy methodology, intended to assess models of integration across stimulus dimensions (features, modalities, etc.) that were proposed by Shaw and colleagues (e.g., Mulligan & Shaw Perception & Psychophysics 28, 471-478, 1980). The goal was to theoretically examine these separate strategies and to apply them conjointly to the same set of participants. The empirical phases were carried out within an extension of an established experimental design called the double factorial paradigm (e.g., Townsend & Nozawa Journal of Mathematical Psychology 39, 321-359, 1995). That paradigm, based on response times, permits assessments of architecture (parallel vs. serial processing), stopping rule (exhaustive vs. minimum time), and workload capacity, all within the same blocks of trials. The paradigm introduced by Shaw and colleagues uses a statistic formally analogous to that of the double factorial paradigm, but based on accuracy rather than response times. We demonstrate that the accuracy measure cannot discriminate between parallel and serial processing. Nonetheless, the class of models supported by the accuracy data possesses a suitable interpretation within the same set of models supported by the response-time data. The supported model, consistent across individuals, is parallel and has limited capacity, with the participants employing the appropriate stopping rule for the experimental setting.

  3. Conceptual and methodological challenges to integrating SEA and cumulative effects assessment

    International Nuclear Information System (INIS)

    Gunn, Jill; Noble, Bram F.

    2011-01-01

    The constraints to assessing and managing cumulative environmental effects in the context of project-based environmental assessment are well documented, and the potential benefits of a more strategic approach to cumulative effects assessment (CEA) are well argued; however, such benefits have yet to be clearly demonstrated in practice. While it is widely assumed that cumulative effects are best addressed in a strategic context, there has been little investigation as to whether CEA and strategic environmental assessment (SEA) are a 'good fit' - conceptually or methodologically. This paper identifies a number of conceptual and methodological challenges to the integration of CEA and SEA. Based on results of interviews with international experts and practitioners, this paper demonstrates that: definitions and conceptualizations of CEA are typically weak in practice; approaches to effects aggregation vary widely; a systems perspective lacks in both SEA and CEA; the multifarious nature of SEA complicates CEA; tiering arrangements between SEA and project-based assessment are limited to non-existing; and the relationship of SEA to regional planning remains unclear.

  4. Vocalist - an international programme for the validation of constraint based methodology in structural integrity

    International Nuclear Information System (INIS)

    Lidbury, D.; Bass, R.; Gilles, Ph.; Connors, D.; Eisele, U.; Keim, E.; Keinanen, H.; Marie, St.; Nagel, G.; Taylor, N.; Wadier, Y.

    2001-01-01

    The pattern of crack-tip stresses and strains causing plastic flow and fracture in components is different to that in test specimens. This gives rise to the so-called constraint effect. Crack-tip constraint in components is generally lower than in test specimens. Effective toughness is correspondingly higher. The fracture toughness measured on test specimens is thus likely to underestimate that exhibited by cracks in components. A 36-month programme was initiated in October 2000 as part of the Fifth Framework of the European Atomic Energy Community (EURATOM), with the objective of achieving (i) an improved defect assessment methodology for predicting safety margins; (ii) improved lifetime management arguments. The programme VOCALIST (Validation of Constraint Based Methodology in Structural Integrity) is one of a 'cluster' of Fifth Framework projects in the area of Plant Life Management (Nuclear Fission). VOCALIST is also an associated project of NESC (Network for Evaluating Steel Components). The present paper describes the aims and objectives of VOCALIST, its interactions with NESC, and gives details of its various Work Packages. (authors)

  5. Vocalist - an international programme for the validation of constraint based methodology in structural integrity

    Energy Technology Data Exchange (ETDEWEB)

    Lidbury, D. [AEA Technology, Consulting (United Kingdom); Bass, R. [Oak Ridge National Lab., TN (United States); Gilles, Ph. [FRAMATOME, 92 - Paris-La-Defence (France); Connors, D. [BNFL Magnox Generation (United Kingdom); Eisele, U. [Multiphoton Absorption, MPA, Stuttgart (Germany); Keim, E. [Framatome ANP GmbH (Germany); Keinanen, H. [VTT Energy, Espoo (Finland); Marie, St. [CEA Saclay, Dept. de Mecanique et de Technologie, 91 - Gif sur Yvette (France); Nagel, G. [E.ON Kernraft (Germany); Taylor, N. [Joint Research Center, JRC-IAM (Netherlands); Wadier, Y. [Electricite de France (EDF), 93 - Saint-Denis (France). Dept. de Radioprotection

    2001-07-01

    The pattern of crack-tip stresses and strains causing plastic flow and fracture in components is different to that in test specimens. This gives rise to the so-called constraint effect. Crack-tip constraint in components is generally lower than in test specimens. Effective toughness is correspondingly higher. The fracture toughness measured on test specimens is thus likely to underestimate that exhibited by cracks in components. A 36-month programme was initiated in October 2000 as part of the Fifth Framework of the European Atomic Energy Community (EURATOM), with the objective of achieving (i) an improved defect assessment methodology for predicting safety margins; (ii) improved lifetime management arguments. The programme VOCALIST (Validation of Constraint Based Methodology in Structural Integrity) is one of a 'cluster' of Fifth Framework projects in the area of Plant Life Management (Nuclear Fission). VOCALIST is also an associated project of NESC (Network for Evaluating Steel Components). The present paper describes the aims and objectives of VOCALIST, its interactions with NESC, and gives details of its various Work Packages. (authors)

  6. Structural integrity assessments of steam generator tubes using the FAD methodology

    Energy Technology Data Exchange (ETDEWEB)

    Bergant, Marcos A., E-mail: marcos.bergant@cab.cnea.gov.ar [Gerencia CAREM, Centro Atómico Bariloche (CNEA), Av. Bustillo 9500, San Carlos de Bariloche 8400 (Argentina); Yawny, Alejandro A., E-mail: yawny@cab.cnea.gov.ar [División Física de Metales, Centro Atómico Bariloche (CNEA)/CONICET, Av. Bustillo 9500, San Carlos de Bariloche 8400 (Argentina); Perez Ipiña, Juan E., E-mail: juan.perezipina@fain.uncoma.edu.ar [Grupo Mecánica de Fractura, Universidad Nacional del Comahue/CONICET, Buenos Aires 1400, Neuquén 8300 (Argentina)

    2015-12-15

    Highlights: • The Failure Assessment Diagram (FAD) is used to assess cracked steam generator tubes. • Typical loading conditions and reported tensile and fracture properties are used. • The FAD is capable to predict the failure mode for different cracks and loads. • The FAD can be used to reduce the conservatism of the current plugging criteria. • Appropriate tensile and fracture properties at operating conditions are required. - Abstract: Steam generator tubes (SGTs) represents up to 60% of the total primary pressure retaining boundary area of a nuclear power plant. They have been found susceptible to diverse degradation mechanisms during service. Due to the significance of a SGT failure on the plant safe operation, nuclear regulatory authorities have established tube plugging or repairing criteria which are based on the defect depth. The widespreadly used “40% criterion” proposed in the 70s is an example whose use is still recommended in the last editions of the ASME Boiler and Pressure Vessel Code. In the present work, an alternative, more realistic and less conservative methodology for SGT integrity evaluation is proposed. It is based on the Failure Assessment Diagram (FAD) and takes advantage of the recent developments in non-destructive techniques which allow a more comprehensive characterization of tube defects, i.e., depth, length, orientation and type. The proposed approach has been applied to: the study of the influence of primary and secondary stresses on tube integrity; the prediction of failure mode (i.e., ductile fracture or plastic collapse) of defective SGTs for varied crack geometries and loading conditions; the analysis of the sensibility of tensile and fracture properties with temperature. The potentiality of the FAD as a comprehensive methodology for predicting the failure loads and failure modes of flawed SGTs is highlighted.

  7. Structural integrity assessments of steam generator tubes using the FAD methodology

    International Nuclear Information System (INIS)

    Bergant, Marcos A.; Yawny, Alejandro A.; Perez Ipiña, Juan E.

    2015-01-01

    Highlights: • The Failure Assessment Diagram (FAD) is used to assess cracked steam generator tubes. • Typical loading conditions and reported tensile and fracture properties are used. • The FAD is capable to predict the failure mode for different cracks and loads. • The FAD can be used to reduce the conservatism of the current plugging criteria. • Appropriate tensile and fracture properties at operating conditions are required. - Abstract: Steam generator tubes (SGTs) represents up to 60% of the total primary pressure retaining boundary area of a nuclear power plant. They have been found susceptible to diverse degradation mechanisms during service. Due to the significance of a SGT failure on the plant safe operation, nuclear regulatory authorities have established tube plugging or repairing criteria which are based on the defect depth. The widespreadly used “40% criterion” proposed in the 70s is an example whose use is still recommended in the last editions of the ASME Boiler and Pressure Vessel Code. In the present work, an alternative, more realistic and less conservative methodology for SGT integrity evaluation is proposed. It is based on the Failure Assessment Diagram (FAD) and takes advantage of the recent developments in non-destructive techniques which allow a more comprehensive characterization of tube defects, i.e., depth, length, orientation and type. The proposed approach has been applied to: the study of the influence of primary and secondary stresses on tube integrity; the prediction of failure mode (i.e., ductile fracture or plastic collapse) of defective SGTs for varied crack geometries and loading conditions; the analysis of the sensibility of tensile and fracture properties with temperature. The potentiality of the FAD as a comprehensive methodology for predicting the failure loads and failure modes of flawed SGTs is highlighted.

  8. Antibody- and TRIM21-dependent intracellular restriction of Salmonella enterica.

    Science.gov (United States)

    Rakebrandt, Nikolas; Lentes, Sabine; Neumann, Heinz; James, Leo C; Neumann-Staubitz, Petra

    2014-11-01

    TRIM21 ('tripartite motif-containing protein 21', Ro52) is a ubiquitously expressed cytosolic Fc receptor, which has a potent role in protective immunity against nonenveloped viruses. TRIM21 mediates intracellular neutralisation of antibody-coated viruses, a process called ADIN (antibody-dependent intracellular neutralisation). Our results reveal a similar mechanism to fight bacterial infections. TRIM21 is recruited to the intracellular pathogen Salmonella enterica in epithelial cells early in infection. TRIM21 does not bind directly to S. enterica, but to antibodies opsonising it. Most importantly, bacterial restriction is dependent on TRIM21 as well as on the opsonisation state of the bacteria. Finally, Salmonella and TRIM21 colocalise with the autophagosomal marker LC3, and intracellular defence is enhanced in starved cells suggesting an involvement of the autophagocytic pathway. Our data extend the protective role of TRIM21 from viruses to bacteria and thereby strengthening the general role of ADIN in cellular immunity. © 2014 Federation of European Microbiological Societies. Published by John Wiley & Sons Ltd. All rights reserved.

  9. A Methodology for Multiple Rule System Integration and Resolution Within a Singular Knowledge Base

    Science.gov (United States)

    Kautzmann, Frank N., III

    1988-01-01

    Expert Systems which support knowledge representation by qualitative modeling techniques experience problems, when called upon to support integrated views embodying description and explanation, especially when other factors such as multiple causality, competing rule model resolution, and multiple uses of knowledge representation are included. A series of prototypes are being developed to demonstrate the feasibility of automating the process of systems engineering, design and configuration, and diagnosis and fault management. A study involves not only a generic knowledge representation; it must also support multiple views at varying levels of description and interaction between physical elements, systems, and subsystems. Moreover, it will involve models of description and explanation for each level. This multiple model feature requires the development of control methods between rule systems and heuristics on a meta-level for each expert system involved in an integrated and larger class of expert system. The broadest possible category of interacting expert systems is described along with a general methodology for the knowledge representation and control of mutually exclusive rule systems.

  10. An integrated probabilistic risk analysis decision support methodology for systems with multiple state variables

    International Nuclear Information System (INIS)

    Sen, P.; Tan, John K.G.; Spencer, David

    1999-01-01

    Probabilistic risk analysis (PRA) methods have been proven to be valuable in risk and reliability analysis. However, a weak link seems to exist between methods for analysing risks and those for making rational decisions. The integrated decision support system (IDSS) methodology presented in this paper attempts to address this issue in a practical manner. In consists of three phases: a PRA phase, a risk sensitivity analysis (SA) phase and an optimisation phase, which are implemented through an integrated computer software system. In the risk analysis phase the problem is analysed by the Boolean representation method (BRM), a PRA method that can deal with systems with multiple state variables and feedback loops. In the second phase the results obtained from the BRM are utilised directly to perform importance and risk SA. In the third phase, the problem is formulated as a multiple objective decision making problem in the form of multiple objective reliability optimisation. An industrial example is included. The resultant solutions of a five objective reliability optimisation are presented, on the basis of which rational decision making can be explored

  11. Elastic-Plastic J-Integral Solutions or Surface Cracks in Tension Using an Interpolation Methodology

    Science.gov (United States)

    Allen, P. A.; Wells, D. N.

    2013-01-01

    No closed form solutions exist for the elastic-plastic J-integral for surface cracks due to the nonlinear, three-dimensional nature of the problem. Traditionally, each surface crack must be analyzed with a unique and time-consuming nonlinear finite element analysis. To overcome this shortcoming, the authors have developed and analyzed an array of 600 3D nonlinear finite element models for surface cracks in flat plates under tension loading. The solution space covers a wide range of crack shapes and depths (shape: 0.2 less than or equal to a/c less than or equal to 1, depth: 0.2 less than or equal to a/B less than or equal to 0.8) and material flow properties (elastic modulus-to-yield ratio: 100 less than or equal to E/ys less than or equal to 1,000, and hardening: 3 less than or equal to n less than or equal to 20). The authors have developed a methodology for interpolating between the goemetric and material property variables that allows the user to reliably evaluate the full elastic-plastic J-integral and force versus crack mouth opening displacement solution; thus, a solution can be obtained very rapidly by users without elastic-plastic fracture mechanics modeling experience. Complete solutions for the 600 models and 25 additional benchmark models are provided in tabular format.

  12. Integrated analytical methodologies for the study of corrosion processes in archaeological bronzes

    Energy Technology Data Exchange (ETDEWEB)

    Alberghina, Maria Francesca; Barraco, Rosita; Brai, Maria; Schillaci, Tiziano, E-mail: tschillaci@unipa.it; Tranchina, Luigi

    2011-02-15

    The investigations on structure and micro-chemical composition of archaeological metal alloys are needed in archaeometry. The aim of this study is devoted both to acquire information about their provenance and production technology, and to improve our understanding about the corrosion processes. In this paper we present the study of the corrosion phenomena of bronze samples, laboratory-made according to binary, ternary and quaternary alloys typical of Roman archaeometallurgical production through an integrated methodology based on the use of non or micro invasive physical techniques. Among the analysed samples, two were artificially aged through burial in the archaeological site of Tharros, along the west coast of Sardinia (Italy). The corrosion products, typical of the bronzes in archaeological sites near the sea, have been characterized by non invasive and micro-destructive measurements. In particular, the corrosion patinas were examined through optical microscopy, scanning electron microscopy and microanalysis, X-ray fluorescence and laser ablation spectroscopy. The use of integrated technologies allowed us to determine both the elemental composition and surface morphology of the patina, highlighting the correlation between patina nature and chemical composition of the burial context. Moreover, data obtained by the laser-induced breakdown spectroscopy along the depth profile on the samples, have yielded information about the stratigraphic layers of corrosion products and their growth. Finally, the depth profiles allowed us to verify both the chemical elements constituting the patina, the metal ions constituting the alloy and the occurrence of migration phenomena from bulk to the surface.

  13. Integrated analytical methodologies for the study of corrosion processes in archaeological bronzes

    International Nuclear Information System (INIS)

    Alberghina, Maria Francesca; Barraco, Rosita; Brai, Maria; Schillaci, Tiziano; Tranchina, Luigi

    2011-01-01

    The investigations on structure and micro-chemical composition of archaeological metal alloys are needed in archaeometry. The aim of this study is devoted both to acquire information about their provenance and production technology, and to improve our understanding about the corrosion processes. In this paper we present the study of the corrosion phenomena of bronze samples, laboratory-made according to binary, ternary and quaternary alloys typical of Roman archaeometallurgical production through an integrated methodology based on the use of non or micro invasive physical techniques. Among the analysed samples, two were artificially aged through burial in the archaeological site of Tharros, along the west coast of Sardinia (Italy). The corrosion products, typical of the bronzes in archaeological sites near the sea, have been characterized by non invasive and micro-destructive measurements. In particular, the corrosion patinas were examined through optical microscopy, scanning electron microscopy and microanalysis, X-ray fluorescence and laser ablation spectroscopy. The use of integrated technologies allowed us to determine both the elemental composition and surface morphology of the patina, highlighting the correlation between patina nature and chemical composition of the burial context. Moreover, data obtained by the laser-induced breakdown spectroscopy along the depth profile on the samples, have yielded information about the stratigraphic layers of corrosion products and their growth. Finally, the depth profiles allowed us to verify both the chemical elements constituting the patina, the metal ions constituting the alloy and the occurrence of migration phenomena from bulk to the surface.

  14. An IMM-Aided ZUPT Methodology for an INS/DVL Integrated Navigation System.

    Science.gov (United States)

    Yao, Yiqing; Xu, Xiaosu; Xu, Xiang

    2017-09-05

    Inertial navigation system (INS)/Doppler velocity log (DVL) integration is the most common navigation solution for underwater vehicles. Due to the complex underwater environment, the velocity information provided by DVL always contains some errors. To improve navigation accuracy, zero velocity update (ZUPT) technology is considered, which is an effective algorithm for land vehicles to mitigate the navigation error during the pure INS mode. However, in contrast to ground vehicles, the ZUPT solution cannot be used directly for underwater vehicles because of the existence of the water current. In order to leverage the strengths of the ZUPT method and the INS/DVL solution, an interactive multiple model (IMM)-aided ZUPT methodology for the INS/DVL-integrated underwater navigation system is proposed. Both the INS/DVL and INS/ZUPT models are constructed and operated in parallel, with weights calculated according to their innovations and innovation covariance matrices. Simulations are conducted to evaluate the proposed algorithm. The results indicate that the IMM-aided ZUPT solution outperforms both the INS/DVL solution and the INS/ZUPT solution in the underwater environment, which can properly distinguish between the ZUPT and non-ZUPT conditions. In addition, during DVL outage, the effectiveness of the proposed algorithm is also verified.

  15. Utilization of smoked salmon trim in extruded smoked salmon jerky.

    Science.gov (United States)

    Kong, J; Dougherty, M P; Perkins, L B; Camire, M E

    2012-06-01

    During smoked salmon processing, the dark meat along the lateral line is removed before packaging; this by-product currently has little economic value. In this study, the dark meat trim was incorporated into an extruded jerky. Three formulations were processed: 100% smoked trim, 75% : 25% smoked trim : fresh salmon fillet, and 50% : 50% smoked trim : fresh salmon blends (w/w basis). The base formulation contained salmon (approximately 83.5%), tapioca starch (8%), pregelatinized potato starch (3%), sucrose (4%), salt (1.5%), sodium nitrate (0.02%), and ascorbyl palmitate (0.02% of the lipid content). Blends were extruded in a laboratory-scale twin-screw extruder and then hot-smoked for 5 h. There were no significant differences among formulations in moisture, water activity, and pH. Protein was highest in the 50 : 50 blend jerky. Ash content was highest in the jerky made with 100% trim. Total lipids and salt were higher in the 100% trim jerky than in the 50 : 50 blend. Hot smoking did not adversely affect docosahexaenoic acid (DHA) and eicosapentaenoic acid (EPA) content in lipids from 100% smoked trim jerky. Servings of salmon jerky made with 75% and 100% smoked trim provided at least 500 mg of EPA and DHA. The 50 : 50 formulation had the highest Intl. Commission on Illumination (CIE) L*, a*, and b* color values. Seventy consumers rated all sensory attributes as between "like slightly" and "like moderately." With some formulation and processing refinements, lateral line trim from smoked salmon processors has potential to be incorporated into acceptable, healthful snack products. Dark meat along the lateral line is typically discarded by smoked salmon processors. This omega-3 fatty acid rich by-product can be used to make a smoked salmon jerky that provides a convenient source of these healthful lipids for consumers. © 2012 Institute of Food Technologists®

  16. Application of Various Lasers to Laser Trimming Resistance System

    Institute of Scientific and Technical Information of China (English)

    SUN Ji-feng

    2007-01-01

    Though the laser trimming resistance has been an old laser machining industry for over 30 years, the development of technology brings new alternative lasers which can be used for the traditional machining. The paper describes application of various lasers to laser trimming resistance system including early traditional krypton arc lamp pumped Nd:YAG to laser, modern popular diode pumped solid state laser and the present advanced harmonic diode pumped solid state laser. Using the new alternative lasers in the laser trimming resistance system can dramatically improve the yields and equipment performance.

  17. Technical Report on Preliminary Methodology for Enhancing Risk Monitors with Integrated Equipment Condition Assessment

    Energy Technology Data Exchange (ETDEWEB)

    Ramuhalli, Pradeep; Coles, Garill A.; Coble, Jamie B.; Hirt, Evelyn H.

    2013-09-17

    Small modular reactors (SMRs) generally include reactors with electric output of ~350 MWe or less (this cutoff varies somewhat but is substantially less than full-size plant output of 700 MWe or more). Advanced SMRs (AdvSMRs) refer to a specific class of SMRs and are based on modularization of advanced reactor concepts. AdvSMRs may provide a longer-term alternative to traditional light-water reactors (LWRs) and SMRs based on integral pressurized water reactor concepts currently being considered. Enhancing affordability of AdvSMRs will be critical to ensuring wider deployment. AdvSMRs suffer from loss of economies of scale inherent in small reactors when compared to large (~greater than 600 MWe output) reactors. Some of this loss can be recovered through reduced capital costs through smaller size, fewer components, modular fabrication processes, and the opportunity for modular construction. However, the controllable day-to-day costs of AdvSMRs will be dominated by operation and maintenance (O&M) costs. Technologies that help characterize real-time risk are important for controlling O&M costs. Risk monitors are used in current nuclear power plants to provide a point-in-time estimate of the system risk given the current plant configuration (e.g., equipment availability, operational regime, and environmental conditions). However, current risk monitors are unable to support the capability requirements listed above as they do not take into account plant-specific normal, abnormal, and deteriorating states of active components and systems. This report documents technology developments that are a step towards enhancing risk monitors that, if integrated with supervisory plant control systems, can provide the capability requirements listed and meet the goals of controlling O&M costs. The report describes research results from an initial methodology for enhanced risk monitors by integrating real-time information about equipment condition and POF into risk monitors.

  18. A combined reaction class approach with integrated molecular orbital+molecular orbital (IMOMO) methodology: A practical tool for kinetic modeling

    International Nuclear Information System (INIS)

    Truong, Thanh N.; Maity, Dilip K.; Truong, Thanh-Thai T.

    2000-01-01

    We present a new practical computational methodology for predicting thermal rate constants of reactions involving large molecules or a large number of elementary reactions in the same class. This methodology combines the integrated molecular orbital+molecular orbital (IMOMO) approach with our recently proposed reaction class models for tunneling. With the new methodology, we show that it is possible to significantly reduce the computational cost by several orders of magnitude while compromising the accuracy in the predicted rate constants by less than 40% over a wide range of temperatures. Another important result is that the computational cost increases only slightly as the system size increases. (c) 2000 American Institute of Physics

  19. An integrated methodology to forecast the efficiency of nourishment strategies in eroding deltas.

    Science.gov (United States)

    Bergillos, Rafael J; López-Ruiz, Alejandro; Principal-Gómez, Daniel; Ortega-Sánchez, Miguel

    2018-02-01

    Many deltas across the globe are retreating, and nearby beaches are undergoing strong erosion as a result. Among soft and prompt solutions, nourishments are the most heavily used. This paper presents an integrated methodology to forecast the efficiency of nourishment strategies by means of wave climate simulations, wave propagations with downscaling techniques, computation of longshore sediment transport rates and application of the one-line model. It was applied to an eroding deltaic beach (Guadalfeo, southern Spain), where different scenarios as a function of the nourished coastline morphology, input volume and grain size were tested. For that, the evolution of six scenarios of coastline geometry over a two-year period (lifetime of nourishment projects at the study site) was modelled and the uncertainty of the predictions was also quantified through Monte Carlo techniques. For the most efficient coastline shape in terms of gained dry beach area, eight sub-scenarios with different nourished volumes were defined and modelled. The results indicate that an input volume around 460,000m 3 is the best strategy since nourished morphologies with higher volumes are more exposed to the prevailing storm directions, inducing less efficient responses. After setting the optimum coastline morphology and input sediment volume, eleven different nourished grain sizes were modelled; the most efficient coastline responses were obtained for sediment sizes greater than 0.01m. The availability of these sizes in the sediment accumulated upstream of a dam in the Guadalfeo River basin allows for the conclusion that this alternative would not only mitigate coastal erosion problems but also sedimentation issues in the reservoir. The methodology proposed in this work is extensible to other coastal areas across the world and can be helpful to support the decision-making process of artificial nourishment projects and other environmental management strategies. Copyright © 2017 Elsevier B.V. All

  20. The molluscan RING-finger protein L-TRIM is essential for neuronal outgrowth

    NARCIS (Netherlands)

    van Diepen, M. T.; Spencer, G.E.; Minnen, J.; Gouwenberg, Y.; Bouwman, J.G.; Smit, A. B.; van Kesteren, R.E.

    2005-01-01

    The tripartite motif proteins TRIM-2 and TRIM-3 have been put forward as putative organizers of neuronal outgrowth and structural plasticity. Here, we identified a molluscan orthologue of TRIM-2/3, named L-TRIM, which is up-regulated during in vitro neurite outgrowth of central neurons. In adult

  1. Automatic channel trimming for control systems: A concept

    Science.gov (United States)

    Vandervoort, R. J.; Sykes, H. A.

    1977-01-01

    Set of bias signals added to channel inputs automatically normalize differences between channels. Algorithm and second feedback loop compute trim biases. Concept could be applied to regulators and multichannel servosystems for remote manipulators in undersea mining.

  2. Old trims for new: the cheaper solution to valve problems

    Energy Technology Data Exchange (ETDEWEB)

    Katz, B [Control Components, Inc., Rancho Santa Margarita, CA (United States)

    1994-01-01

    Rather than replacing a faulty valve - or one that is simply not up to the job - it has been possible to retrofit a variety of valve types used in nuclear plants with new trims which are described briefly. (Author).

  3. Old trims for new: the cheaper solution to valve problems

    International Nuclear Information System (INIS)

    Katz, B.

    1994-01-01

    Rather than replacing a faulty valve - or one that is simply not up to the job - it has been possible to retrofit a variety of valve types used in nuclear plants with new trims which are described briefly. (Author)

  4. Wrinkling reduction of membrane structure by trimming edges

    Directory of Open Access Journals (Sweden)

    Mingjun Liu

    2017-05-01

    Full Text Available Thin membranes have negligible bending stiffness, compressive stresses inevitably lead to wrinkling. Therefore, it is important to keep the surface of membrane structures flat in order to guarantee high precision. Edge-trimming is an effective method to passively diminish wrinkles, however a key difficulty in this process is the determination of the optimal trimming level. In this paper, regular polygonal membrane structures subjected to equal radial forces were analyzed, and a new stress field distribution model for arc-edge square membrane structure was proposed to predict the optimal trimming level. This model is simple and applicable to any polygonal membrane structures. Comparison among the results of the finite element analysis, and the experimental and analytical results showed that the proposed model accurately described the stress field distribution and guaranteed that there are no wrinkles appear inside the effective inscribed circle region for the optimal trimming level.

  5. Investigation of an automatic trim algorithm for restructurable aircraft control

    Science.gov (United States)

    Weiss, J.; Eterno, J.; Grunberg, D.; Looze, D.; Ostroff, A.

    1986-01-01

    This paper develops and solves an automatic trim problem for restructurable aircraft control. The trim solution is applied as a feed-forward control to reject measurable disturbances following control element failures. Disturbance rejection and command following performances are recovered through the automatic feedback control redesign procedure described by Looze et al. (1985). For this project the existence of a failure detection mechanism is assumed, and methods to cope with potential detection and identification inaccuracies are addressed.

  6. An Updated Methodology for Enhancing Risk Monitors with Integrated Equipment Condition Assessment

    Energy Technology Data Exchange (ETDEWEB)

    Ramuhalli, Pradeep [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Hirt, Evelyn H. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Coles, Garill A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Bonebrake, Christopher A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Ivans, William J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wootan, David W. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Mitchell, Mark R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2014-07-18

    Small modular reactors (SMRs) generally include reactors with electric output of ~350 MWe or less (this cutoff varies somewhat but is substantially less than full-size plant output of 700 MWe or more). Advanced SMRs (AdvSMRs) refer to a specific class of SMRs and are based on modularization of advanced reactor concepts. Enhancing affordability of AdvSMRs will be critical to ensuring wider deployment, as AdvSMRs suffer from loss of economies of scale inherent in small reactors when compared to large (~greater than 600 MWe output) reactors and the controllable day-to-day costs of AdvSMRs will be dominated by operation and maintenance (O&M) costs. Technologies that help characterize real-time risk are important for controlling O&M costs. Risk monitors are used in current nuclear power plants to provide a point-in-time estimate of the system risk given the current plant configuration (e.g., equipment availability, operational regime, and environmental conditions). However, current risk monitors are unable to support the capability requirements listed above as they do not take into account plant-specific normal, abnormal, and deteriorating states of active components and systems. This report documents technology developments towards enhancing risk monitors that, if integrated with supervisory plant control systems, can provide the capability requirements listed and meet the goals of controlling O&M costs. The report describes research results on augmenting an initial methodology for enhanced risk monitors that integrate real-time information about equipment condition and POF into risk monitors. Methods to propagate uncertainty through the enhanced risk monitor are evaluated. Available data to quantify the level of uncertainty and the POF of key components are examined for their relevance, and a status update of this data evaluation is described. Finally, we describe potential targets for developing new risk metrics that may be useful for studying trade-offs for economic

  7. Trimming the UCERF2 hazard logic tree

    Science.gov (United States)

    Porter, Keith A.; Field, Edward H.; Milner, Kevin

    2012-01-01

    The Uniform California Earthquake Rupture Forecast 2 (UCERF2) is a fully time‐dependent earthquake rupture forecast developed with sponsorship of the California Earthquake Authority (Working Group on California Earthquake Probabilities [WGCEP], 2007; Field et al., 2009). UCERF2 contains 480 logic‐tree branches reflecting choices among nine modeling uncertainties in the earthquake rate model shown in Figure 1. For seismic hazard analysis, it is also necessary to choose a ground‐motion‐prediction equation (GMPE) and set its parameters. Choosing among four next‐generation attenuation (NGA) relationships results in a total of 1920 hazard calculations per site. The present work is motivated by a desire to reduce the computational effort involved in a hazard analysis without understating uncertainty. We set out to assess which branching points of the UCERF2 logic tree contribute most to overall uncertainty, and which might be safely ignored (set to only one branch) without significantly biasing results or affecting some useful measure of uncertainty. The trimmed logic tree will have all of the original choices from the branching points that contribute significantly to uncertainty, but only one arbitrarily selected choice from the branching points that do not.

  8. Printed board dipole trim magnet design for 20 MeV LIA

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Chengjun; Zhu, Wenjun; Zhang, Kaizhi; Zhang, Wenwei; Yu, Haijun [China Academy of Engineering Physics., Chengdu (China). Inst. of Fluid Physics

    1997-12-31

    The printed board dipole trim magnet design for a 20 MeV LIA is presented. The prototype dipole magnet with the sin/cos distributed windings has demonstrated more than 650 Gs-cm integrated dipole field and 1% integrated dipole field homogeneity within 5 cm in radius, which is about 40% of the magnet radius. Numerical modeling of two prototype magnet designs using the 3D magnetic field code SCMAG is presented as well as data from magnetic field measurements of the two magnets. The agreement between the calculations and measurements is accurate to 2-3%. (author). 3 figs., 4 refs.

  9. Loss of heterozygosity of TRIM3 in malignant gliomas

    International Nuclear Information System (INIS)

    Boulay, Jean-Louis; Stiefel, Urs; Taylor, Elisabeth; Dolder, Béatrice; Merlo, Adrian; Hirth, Frank

    2009-01-01

    Malignant gliomas are frequent primary brain tumors associated with poor prognosis and very limited response to conventional chemo- and radio-therapies. Besides sharing common growth features with other types of solid tumors, gliomas are highly invasive into adjacent brain tissue, which renders them particularly aggressive and their surgical resection inefficient. Therefore, insights into glioma formation are of fundamental interest in order to provide novel molecular targets for diagnostic purposes and potential anti-cancer drugs. Human Tripartite motif protein 3 (TRIM3) encodes a structural homolog of Drosophila brain tumor (brat) implicated in progenitor cell proliferation control and cancer stem cell suppression. TRIM3 is located within the loss of allelic heterozygosity (LOH) hotspot of chromosome segment 11p15.5, indicating a potential role in tumor suppression. ... Here we analyze 70 primary human gliomas of all types and grades and report somatic deletion mapping as well as single nucleotide polymorphism analysis together with quantitative real-time PCR of chromosome segment 11p15.5. Our analysis identifies LOH in 17 cases (24%) of primary human glioma which defines a common 130 kb-wide interval within the TRIM3 locus as a minimal area of loss. We further detect altered genomic dosage of TRIM3 in two glioma cases with LOH at 11p15.5, indicating homozygous deletions of TRIM3. Loss of heterozygosity of chromosome segment 11p15.5 in malignant gliomas suggests TRIM3 as a candidate brain tumor suppressor gene

  10. An integrated methodology on the suitability of offshore sites for wind farm development

    Science.gov (United States)

    Patlakas, Platon; Galanis, George; Péray, Marie; Filipot, Jean-François; Kalogeri, Christina; Spyrou, Christos; Diamantis, Dimitris; Kallos, Gerorge

    2016-04-01

    During, the last decades the potential and interest in wind energy investments has been constantly increasing in the European countries. As technology changes rapidly, more and more areas can be identified as suitable for energy applications. Offshore wind farms perfectly illustrate how new technologies allow to build bigger, more efficient and resistant in extreme conditions wind power plants. The current work proposes an integrated methodology to determine the suitability of an offshore marine area for the development of wind farm structures. More specifically, the region of interest is evaluated based both on the natural resources, connected to the local environmental characteristics, and potential constrains set by anthropogenic or other activities. State of the art atmospheric and wave models and a 10-year hindcast database are utilized in conjunction with local information for a number of potential constrains, leading to a 5-scale suitability index for the whole area. In this way, sub regions are characterized, at a high resolution mode, as poorly or highly suitable for wind farm development, providing a new tool for technical/research teams and decision makers. In addition, extreme wind and wave conditions and their 50-years return period are analyzed and used to define the safety level of the wind farms structural characteristics.

  11. Methodological integrative review of the work sampling technique used in nursing workload research.

    Science.gov (United States)

    Blay, Nicole; Duffield, Christine M; Gallagher, Robyn; Roche, Michael

    2014-11-01

    To critically review the work sampling technique used in nursing workload research. Work sampling is a technique frequently used by researchers and managers to explore and measure nursing activities. However, work sampling methods used are diverse making comparisons of results between studies difficult. Methodological integrative review. Four electronic databases were systematically searched for peer-reviewed articles published between 2002-2012. Manual scanning of reference lists and Rich Site Summary feeds from contemporary nursing journals were other sources of data. Articles published in the English language between 2002-2012 reporting on research which used work sampling to examine nursing workload. Eighteen articles were reviewed. The review identified that the work sampling technique lacks a standardized approach, which may have an impact on the sharing or comparison of results. Specific areas needing a shared understanding included the training of observers and subjects who self-report, standardization of the techniques used to assess observer inter-rater reliability, sampling methods and reporting of outcomes. Work sampling is a technique that can be used to explore the many facets of nursing work. Standardized reporting measures would enable greater comparison between studies and contribute to knowledge more effectively. Author suggestions for the reporting of results may act as guidelines for researchers considering work sampling as a research method. © 2014 John Wiley & Sons Ltd.

  12. Transboundary Water: Improving Methodologies and Developing Integrated Tools to Support Water Security

    Science.gov (United States)

    Hakimdavar, Raha; Wood, Danielle; Eylander, John; Peters-Lidard, Christa; Smith, Jane; Doorn, Brad; Green, David; Hummel, Corey; Moore, Thomas C.

    2018-01-01

    River basins for which transboundary coordination and governance is a factor are of concern to US national security, yet there is often a lack of sufficient data-driven information available at the needed time horizons to inform transboundary water decision-making for the intelligence, defense, and foreign policy communities. To address this need, a two-day workshop entitled Transboundary Water: Improving Methodologies and Developing Integrated Tools to Support Global Water Security was held in August 2017 in Maryland. The committee that organized and convened the workshop (the Organizing Committee) included representatives from the National Aeronautics and Space Administration (NASA), the US Army Corps of Engineers Engineer Research and Development Center (ERDC), and the US Air Force. The primary goal of the workshop was to advance knowledge on the current US Government and partners' technical information needs and gaps to support national security interests in relation to transboundary water. The workshop also aimed to identify avenues for greater communication and collaboration among the scientific, intelligence, defense, and foreign policy communities. The discussion around transboundary water was considered in the context of the greater global water challenges facing US national security.

  13. Optimization of a High Temperature PEMFC micro-CHP System by Formulation and Application of a Process Integration Methodology

    DEFF Research Database (Denmark)

    Arsalis, Alexandros; Nielsen, Mads Pagh; Kær, Søren Knudsen

    2013-01-01

    A 1 kWe micro combined heat and power (CHP) system based on high temperature proton exchange membrane fuel cell (PEMFC) technology is modeled and optimized by formulation and application of a process integration methodology. The system can provide heat and electricity for a singlefamily household...

  14. Validation of an Integrative Methodology to Assess and Monitor Reductive Dechlorination of Chlorinated Ethenes in Contaminated Aquifers

    Czech Academy of Sciences Publication Activity Database

    Tarnawski, S.E.; Rossi, P.; Brennerová, Mária; Stavělová, M.; Holliger, Ch.

    2016-01-01

    Roč. 4, February (2016), s. 7 E-ISSN 2296-665X R&D Projects: GA TA ČR TA02020534 Institutional support: RVO:61388971 Keywords : dechlorination * integrative methodology * chlorinated ethenes Subject RIV: EE - Microbiology, Virology

  15. Application of Decomposition Methodology to Solve Integrated Process Design and Controller Design Problems for Reactor-Separator-Recycle System

    DEFF Research Database (Denmark)

    Abd.Hamid, Mohd-Kamaruddin; Sin, Gürkan; Gani, Rafiqul

    2010-01-01

    This paper presents the integrated process design and controller design (IPDC) for a reactor-separator-recycle (RSR) system and evaluates a decomposition methodology to solve the IPDC problem. Accordingly, the IPDC problem is solved by decomposing it into four hierarchical stages: (i) pre...... the design of a RSR system involving consecutive reactions, A B -> C and shown to provide effective solutions that satisfy design, control and cost criteria. The advantage of the proposed methodology is that it is systematic, makes use of thermodynamic-process knowledge and provides valuable insights......-analysis, (ii) design analysis, (iii) controller design analysis, and (iv) final selection and verification. The methodology makes use of thermodynamic-process insights and the reverse design approach to arrive at the final process-controller design decisions. The developed methodology is illustrated through...

  16. Crack Growth-Based Predictive Methodology for the Maintenance of the Structural Integrity of Repaired and Nonrepaired Aging Engine Stationary Components

    National Research Council Canada - National Science Library

    Barron, Michael

    1999-01-01

    .... Specifically, the FAA's goal was to develop "Crack Growth-Based Predictive Methodologies for the Maintenance of the Structural Integrity of Repaired and Nonrepaired Aging Engine Stationary Components...

  17. Interrelationships between man, energy, and water quality: a new methodology for integrative analyses

    International Nuclear Information System (INIS)

    Kaplan, E.; Thode, H.C. Jr.

    1979-01-01

    The STORET/MSP option was used to obtain county aggregated information on ambient water quality for sixty parameters during the period 1950 to 1978. Masks, extended EXTRACT specifications and bounds on allowable values limited inclusion of erroneous data. Remark codes were required to aggregate STORET parameters to obtain increased numbers of observations. Numerous statistical analyses led to the conclusions that medians were more useful than means, that trimming on number of observations was required to eliminate counties with extreme values, and that many parameters required logarithmic transformation to be useful in regional analyses. County aggregated data for nineteen water quality parameters were examined in terms of their ability to describe qualitative chemical characteristics of water. Anion--cation balances as well as expected relationships between conductivity and other parameters were correctly accounted for. Factor analysis indicated the existence of three principal components describing patterns between metal ions, non-metal ions, and alkalinity-bicarbonate, respectively. These factors were used in place of the original complete set of water quality parameters in a structural equation approach describing relationships between variables of mans activites. It was found that counties with high industrial electric consumption, farming and mineral shipments tended to have increased levels of most water quality parameters. It was also found that simpler path diagrams may be indicated to reduce the effects of redundancy in adequately describing energy--water relationships

  18. Methodology and software to detect viral integration site hot-spots

    Science.gov (United States)

    2011-01-01

    Background Modern gene therapy methods have limited control over where a therapeutic viral vector inserts into the host genome. Vector integration can activate local gene expression, which can cause cancer if the vector inserts near an oncogene. Viral integration hot-spots or 'common insertion sites' (CIS) are scrutinized to evaluate and predict patient safety. CIS are typically defined by a minimum density of insertions (such as 2-4 within a 30-100 kb region), which unfortunately depends on the total number of observed VIS. This is problematic for comparing hot-spot distributions across data sets and patients, where the VIS numbers may vary. Results We develop two new methods for defining hot-spots that are relatively independent of data set size. Both methods operate on distributions of VIS across consecutive 1 Mb 'bins' of the genome. The first method 'z-threshold' tallies the number of VIS per bin, converts these counts to z-scores, and applies a threshold to define high density bins. The second method 'BCP' applies a Bayesian change-point model to the z-scores to define hot-spots. The novel hot-spot methods are compared with a conventional CIS method using simulated data sets and data sets from five published human studies, including the X-linked ALD (adrenoleukodystrophy), CGD (chronic granulomatous disease) and SCID-X1 (X-linked severe combined immunodeficiency) trials. The BCP analysis of the human X-linked ALD data for two patients separately (774 and 1627 VIS) and combined (2401 VIS) resulted in 5-6 hot-spots covering 0.17-0.251% of the genome and containing 5.56-7.74% of the total VIS. In comparison, the CIS analysis resulted in 12-110 hot-spots covering 0.018-0.246% of the genome and containing 5.81-22.7% of the VIS, corresponding to a greater number of hot-spots as the data set size increased. Our hot-spot methods enable one to evaluate the extent of VIS clustering, and formally compare data sets in terms of hot-spot overlap. Finally, we show that the

  19. Conservatism in methodologies for moderator subcooling sufficiency for fuel channel integrity upon pressure tube and calandria tube contact

    Energy Technology Data Exchange (ETDEWEB)

    Sun, L., E-mail: LSun@nbpower.com [Point Lepreau Generating Station, Lepreau, NB, (Canada)

    2015-07-01

    During a postulated large LOCA event in CANDU reactors, the pressure tube may balloon to contact with its surrounding calandria tube to transfer heat to the moderator. To confirm the integrity of the fuel channel in this case, many experiments have been performed in the last three decades. Based on the extant database of the pressure tube/calandria tube (PT/CT) contact, an analytical methodology was developed by Canadian Nuclear Industry to determine the sufficiency of moderator subcooling for fuel channel integrity. At the same time a semi-empirical methodology with an idea of Equivalent Moderator Subcooling (EMS) was also developed to judge the sufficiency of the moderator. In this work, some discussions were made over the two methodologies on their conservatism and it is demonstrated that the analytical approach is over conservative comparing with the EMS methodology. By using the EMS methodology, it is demonstrated that applying glass-peened calandria tubes, the requirement to moderator subcooling can be reduced by 10{sup o}C from that for smooth calandria tubes. (author)

  20. Proposition of a modeling and an analysis methodology of integrated reverse logistics chain in the direct chain

    Directory of Open Access Journals (Sweden)

    Faycal Mimouni

    2016-04-01

    Full Text Available Purpose: Propose a modeling and analysis methodology based on the combination of Bayesian networks and Petri networks of the reverse logistics integrated the direct supply chain. Design/methodology/approach: Network modeling by combining Petri and Bayesian network. Findings: Modeling with Bayesian network complimented with Petri network to break the cycle problem in the Bayesian network. Research limitations/implications: Demands are independent from returns. Practical implications: Model can only be used on nonperishable products. Social implications: Legislation aspects: Recycling laws; Protection of environment; Client satisfaction via after sale service. Originality/value: Bayesian network with a cycle combined with the Petri Network.

  1. An integrated impact assessment and weighting methodology: evaluation of the environmental consequences of computer display technology substitution.

    Science.gov (United States)

    Zhou, Xiaoying; Schoenung, Julie M

    2007-04-01

    Computer display technology is currently in a state of transition, as the traditional technology of cathode ray tubes is being replaced by liquid crystal display flat-panel technology. Technology substitution and process innovation require the evaluation of the trade-offs among environmental impact, cost, and engineering performance attributes. General impact assessment methodologies, decision analysis and management tools, and optimization methods commonly used in engineering cannot efficiently address the issues needed for such evaluation. The conventional Life Cycle Assessment (LCA) process often generates results that can be subject to multiple interpretations, although the advantages of the LCA concept and framework obtain wide recognition. In the present work, the LCA concept is integrated with Quality Function Deployment (QFD), a popular industrial quality management tool, which is used as the framework for the development of our integrated model. The problem of weighting is addressed by using pairwise comparison of stakeholder preferences. Thus, this paper presents a new integrated analytical approach, Integrated Industrial Ecology Function Deployment (I2-EFD), to assess the environmental behavior of alternative technologies in correlation with their performance and economic characteristics. Computer display technology is used as the case study to further develop our methodology through the modification and integration of various quality management tools (e.g., process mapping, prioritization matrix) and statistical methods (e.g., multi-attribute analysis, cluster analysis). Life cycle thinking provides the foundation for our methodology, as we utilize a published LCA report, which stopped at the characterization step, as our starting point. Further, we evaluate the validity and feasibility of our methodology by considering uncertainty and conducting sensitivity analysis.

  2. Integrating environmental restoration management within DOE using an alternative identification and evaluation procedure: A methodology and a case history

    International Nuclear Information System (INIS)

    Devaurs, M.; Brooks, D.; Kelly, E.; Wagner, S.; Vocke, R.

    1992-01-01

    The process of identifying and evaluating alternative corrective measures is a fundamental integrating part of Environmental Restoration (ER) activities. The process used in the Los Alamos National Laboratory (the Laboratory) ER Program is based on principles and tools from multiattribute decision analysis, a well-developed and proven method for evaluating options in decision situations involving multiple objectives, uncertainty, multiple interested stakeholders in the final decision, and the need for technical input from disparate disciplines. The process provides a methodology that has been extensively developed and reviewed over the past five decades; it provides a methodological structure for incorporating the concepts espoused in the streamlined approach as well as more specific guidelines such as data quality objectives (DQOs). The application of this methodology to the ER Program at Los Alamos is described in this paper

  3. Electrocoagulation and nanofiltration integrated process application in purification of bilge water using response surface methodology.

    Science.gov (United States)

    Akarsu, Ceyhun; Ozay, Yasin; Dizge, Nadir; Elif Gulsen, H; Ates, Hasan; Gozmen, Belgin; Turabik, Meral

    Marine pollution has been considered an increasing problem because of the increase in sea transportation day by day. Therefore, a large volume of bilge water which contains petroleum, oil and hydrocarbons in high concentrations is generated from all types of ships. In this study, treatment of bilge water by electrocoagulation/electroflotation and nanofiltration integrated process is investigated as a function of voltage, time, and initial pH with aluminum electrode as both anode and cathode. Moreover, a commercial NF270 flat-sheet membrane was also used for further purification. Box-Behnken design combined with response surface methodology was used to study the response pattern and determine the optimum conditions for maximum chemical oxygen demand (COD) removal and minimum metal ion contents of bilge water. Three independent variables, namely voltage (5-15 V), initial pH (4.5-8.0) and time (30-90 min) were transformed to coded values. The COD removal percent, UV absorbance at 254 nm, pH value (after treatment), and concentration of metal ions (Ti, As, Cu, Cr, Zn, Sr, Mo) were obtained as responses. Analysis of variance results showed that all the models were significant except for Zn (P > 0.05), because the calculated F values for these models were less than the critical F value for the considered probability (P = 0.05). The obtained R(2) and Radj(2) values signified the correlation between the experimental data and predicted responses: except for the model of Zn concentration after treatment, the high R(2) values showed the goodness of fit of the model. While the increase in the applied voltage showed negative effects, the increases in time and pH showed a positive effect on COD removal efficiency; also the most effective linear term was found as time. A positive sign of the interactive coefficients of the voltage-time and pH-time systems indicated synergistic effect on COD removal efficiency, whereas interaction between voltage and pH showed an antagonistic

  4. Matlab Stability and Control Toolbox: Trim and Static Stability Module

    Science.gov (United States)

    Crespo, Luis G.; Kenny, Sean P.

    2006-01-01

    This paper presents the technical background of the Trim and Static module of the Matlab Stability and Control Toolbox. This module performs a low-fidelity stability and control assessment of an aircraft model for a set of flight critical conditions. This is attained by determining if the control authority available for trim is sufficient and if the static stability characteristics are adequate. These conditions can be selected from a prescribed set or can be specified to meet particular requirements. The prescribed set of conditions includes horizontal flight, take-off rotation, landing flare, steady roll, steady turn and pull-up/ push-over flight, for which several operating conditions can be specified. A mathematical model was developed allowing for six-dimensional trim, adjustable inertial properties, asymmetric vehicle layouts, arbitrary number of engines, multi-axial thrust vectoring, engine(s)-out conditions, crosswind and gyroscopic effects.

  5. Non-local means filter for trim statics

    KAUST Repository

    Huang, Yunsong

    2014-08-05

    Structures will be mispositioned across prestack migration gathers in the presence of inaccuracies in the velocity model. Stacking these misaligned gathers runs the risk of destroying important structures in the stacked migration image. To mitigate this problem, we propose a trim statics inspired by the non-local means algorithm originally developed for image denoising. This method differs from the conventional one in two fundamental respects. First, the trim statics are computed by comparing image patches instead of individual image traces. Second, no global pilot trace is needed because only two migration images at a time participate in trim statics and are stacked into one image. A multitude of migration images are stacked recursively in this two-to-one fashion. Tests with a Gulf of Mexico dataset show a noticeable improvement in the feature coherency of the stacked migration image.

  6. Demonstration and Methodology of Structural Monitoring of Stringer Runs out Composite Areas by Embedded Optical Fiber Sensors and Connectors Integrated during Production in a Composite Plant.

    Science.gov (United States)

    Miguel Giraldo, Carlos; Zúñiga Sagredo, Juan; Sánchez Gómez, José; Corredera, Pedro

    2017-07-21

    Embedding optical fibers sensors into composite structures for Structural Health Monitoring purposes is not just one of the most attractive solutions contributing to smart structures, but also the optimum integration approach that insures maximum protection and integrity of the fibers. Nevertheless this intended integration level still remains an industrial challenge since today there is no mature integration process in composite plants matching all necessary requirements. This article describes the process developed to integrate optical fiber sensors in the Production cycle of a test specimen. The sensors, Bragg gratings, were integrated into the laminate during automatic tape lay-up and also by a secondary bonding process, both in the Airbus Composite Plant. The test specimen, completely representative of the root joint of the lower wing cover of a real aircraft, is comprised of a structural skin panel with the associated stringer run out. The ingress-egress was achieved through the precise design and integration of miniaturized optical connectors compatible with the manufacturing conditions and operational test requirements. After production, the specimen was trimmed, assembled and bolted to metallic plates to represent the real triform and buttstrap, and eventually installed into the structural test rig. The interrogation of the sensors proves the effectiveness of the integration process; the analysis of the strain results demonstrate the good correlation between fiber sensors and electrical gauges in those locations where they are installed nearby, and the curvature and load transfer analysis in the bolted stringer run out area enable demonstration of the consistency of the fiber sensors measurements. In conclusion, this work presents strong evidence of the performance of embedded optical sensors for structural health monitoring purposes, where in addition and most importantly, the fibers were integrated in a real production environment and the ingress

  7. M&A Performance and Economic Impact: Integration and Critical Assessment of Methodological Approach

    Directory of Open Access Journals (Sweden)

    Karolis Andriuskevicius

    2017-11-01

    Full Text Available Purpose of the article: Existing methodologies employed within the M&A performance framework are investigated and critically discuss. Methodology/methods: The research has been carried out as a structured assessment of past literature. The findings from scientific articles and studies by various scholars have been categorized, grouped and summarized to discern a meta-analytic view of the work carried out to date. Scientific aim: The conducted research seeks to ascertain and evaluate theoretically existing methodologies used in empirical studies that would allow proper and critical understanding of the results of various findings in the holistic and global M&As area. Findings: The research elaborates on several key developments in M&A methodology and performance studies carried out in empirical works during the last two decades. The findings help to independently and objectively assess performance of M&A from a holistic perspective. Conclusions: Each methodology measuring either M&A performance on a corporate level or effects of M&A on the economy level shall be interpreted and relied on with caution as each of them dispose their limitations whereas application of these methodologies is subject to data availability and case specific.

  8. Quantifying biopsychosocial aspects in everyday contexts: an integrative methodological approach from the behavioral sciences

    Science.gov (United States)

    Portell, Mariona; Anguera, M Teresa; Hernández-Mendo, Antonio; Jonsson, Gudberg K

    2015-01-01

    Contextual factors are crucial for evaluative research in psychology, as they provide insights into what works, for whom, in what circumstances, in what respects, and why. Studying behavior in context, however, poses numerous methodological challenges. Although a comprehensive framework for classifying methods seeking to quantify biopsychosocial aspects in everyday contexts was recently proposed, this framework does not contemplate contributions from observational methodology. The aim of this paper is to justify and propose a more general framework that includes observational methodology approaches. Our analysis is rooted in two general concepts: ecological validity and methodological complementarity. We performed a narrative review of the literature on research methods and techniques for studying daily life and describe their shared properties and requirements (collection of data in real time, on repeated occasions, and in natural settings) and classification criteria (eg, variables of interest and level of participant involvement in the data collection process). We provide several examples that illustrate why, despite their higher costs, studies of behavior and experience in everyday contexts offer insights that complement findings provided by other methodological approaches. We urge that observational methodology be included in classifications of research methods and techniques for studying everyday behavior and advocate a renewed commitment to prioritizing ecological validity in behavioral research seeking to quantify biopsychosocial aspects. PMID:26089708

  9. Loss of heterozygosity of TRIM3 in malignant gliomas

    Directory of Open Access Journals (Sweden)

    Dolder Béatrice

    2009-02-01

    Full Text Available Abstract Background Malignant gliomas are frequent primary brain tumors associated with poor prognosis and very limited response to conventional chemo- and radio-therapies. Besides sharing common growth features with other types of solid tumors, gliomas are highly invasive into adjacent brain tissue, which renders them particularly aggressive and their surgical resection inefficient. Therefore, insights into glioma formation are of fundamental interest in order to provide novel molecular targets for diagnostic purposes and potential anti-cancer drugs. Human Tripartite motif protein 3 (TRIM3 encodes a structural homolog of Drosophila brain tumor (brat implicated in progenitor cell proliferation control and cancer stem cell suppression. TRIM3 is located within the loss of allelic heterozygosity (LOH hotspot of chromosome segment 11p15.5, indicating a potential role in tumor suppression. ... Methods Here we analyze 70 primary human gliomas of all types and grades and report somatic deletion mapping as well as single nucleotide polymorphism analysis together with quantitative real-time PCR of chromosome segment 11p15.5. Results Our analysis identifies LOH in 17 cases (24% of primary human glioma which defines a common 130 kb-wide interval within the TRIM3 locus as a minimal area of loss. We further detect altered genomic dosage of TRIM3 in two glioma cases with LOH at 11p15.5, indicating homozygous deletions of TRIM3. Conclusion Loss of heterozygosity of chromosome segment 11p15.5 in malignant gliomas suggests TRIM3 as a candidate brain tumor suppressor gene.

  10. INTEGRATED METHODOLOGY OF I.I. MECHNIKOV AND MODERN ADDRESS IMMUNOCORRECTION AT MYASTHENIA

    Directory of Open Access Journals (Sweden)

    Klimova E.M.

    2015-05-01

    Full Text Available Introduction. There is carried out reconstruction of the past in the field of integrated discoveries of well-known scientist I.I. Mechnikov for research of aspects of phagocytic function of immune cells and infectious factors in etiology and pathogenesis of progressing myasthenia. There are analyzed the leading factors which have generated scientific outlook and integrated analytical methodology of knowledge of I.I. Mechnikov – the native of the Kharkov province, the graduate student of the Kharkov Imperial University of 1864, the Nobel prize winner of 1908 for creation of the theory of phagocytosis and the author of set of works in the field of microbiology, immunology and virology. Material & methods. The work studied the mechanisms of disorder of various stages of barrier phagocytic function of neutrophils and frequency of occurrence and various degree of expression of virus persistence at patients with myasthenia is determined. Phagocytosis disturbance leads to uncontrollable development of infections at myasthenia. Advance of muscular delicacy and morph-functional disturbances in thymus, obviously, depend on the individual mechanisms which affect various stages of immune disbalance. The whole century has passed from the moment of creation of the phagocytic theory. For this time all stages of this process have been studied, methodical approaches are developed for an estimation of specific features of this phenomenon, from light microscopy to flowing cytofluorometry. Possibilities of light microscopy allow to visualize the stages of phagocytosis from chemotaxis and adhesions to completeness of digestion by neutrophils in dynamics. And Nitro Blue Tetrazolium Reduction Test (NBTR is used for an estimation of enzymatic activity of phagocytes for initiation of formation of active forms of oxygen at the phagosoma formation stage. The given method allows to investigate stages of oxygen-dependent metabolism of neutrophils. Along with these methods

  11. Methodology for the optimal design of an integrated first and second generation ethanol production plant combined with power cogeneration.

    Science.gov (United States)

    Bechara, Rami; Gomez, Adrien; Saint-Antonin, Valérie; Schweitzer, Jean-Marc; Maréchal, François

    2016-08-01

    The application of methodologies for the optimal design of integrated processes has seen increased interest in literature. This article builds on previous works and applies a systematic methodology to an integrated first and second generation ethanol production plant with power cogeneration. The methodology breaks into process simulation, heat integration, thermo-economic evaluation, exergy efficiency vs. capital costs, multi-variable, evolutionary optimization, and process selection via profitability maximization. Optimization generated Pareto solutions with exergy efficiency ranging between 39.2% and 44.4% and capital costs from 210M$ to 390M$. The Net Present Value was positive for only two scenarios and for low efficiency, low hydrolysis points. The minimum cellulosic ethanol selling price was sought to obtain a maximum NPV of zero for high efficiency, high hydrolysis alternatives. The obtained optimal configuration presented maximum exergy efficiency, hydrolyzed bagasse fraction, capital costs and ethanol production rate, and minimum cooling water consumption and power production rate. Copyright © 2016 Elsevier Ltd. All rights reserved.

  12. Advantages of Westinghouse BWR control rod drop accidents methodology utilizing integrated POLCA-T code

    International Nuclear Information System (INIS)

    Panayotov, Dobromir

    2008-01-01

    The paper focuses on the activities pursued by Westinghouse in the development and licensing of POLCA-T code Control Rod Drop Accident (CRDA) Methodology. The comprehensive CRDA methodology that utilizes PHOENIX4/POLCA7/POLCA-T calculation chain foresees complete cycle-specific analysis. The methodology consists of determination of candidates of control rods (CR) that could cause a significant reactivity excursion if dropped throughout the entire fuel cycle, selection of limiting initial conditions for CRDA transient simulation and transient simulation itself. The Westinghouse methodology utilizes state-of-the-art methods. Unnecessary conservatisms in the methodology have been avoided to allow the accurate prediction of margin to design bases. This is mainly achieved by using the POLCA-T code for dynamic CRDA evaluations. The code belongs to the same calculation chain that is used for core design. Thus the very same reactor, core, cycle and fuel data base is used. This allows also reducing the uncertainties of input data and parameters that determine the energy deposition in the fuel. Uncertainty treatment, very selective use of conservatisms, selection of the initial conditions for limiting case analyses, incorporation into POLCA-T code models of the licensed fuel performance code are also among the means of performing realistic CRDA transient analyses. (author)

  13. CFD-Based Over-Determined Trim Analysis for Optimum Aerodynamic Efficiency, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — The overall objective of this Phase I project is to develop a nonlinear trim module in FUN3D for enabling the determined and over-determined trim analyses to be...

  14. TRIM E3 ligases interfere with early and late stages of the retroviral life cycle.

    Directory of Open Access Journals (Sweden)

    Pradeep D Uchil

    2008-02-01

    Full Text Available Members of the TRIpartite interaction Motif (TRIM family of E3 ligases have been shown to exhibit antiviral activities. Here we report a near comprehensive screen for antiretroviral activities of 55 TRIM proteins (36 human, 19 mouse. We identified approximately 20 TRIM proteins that, when transiently expressed in HEK293 cells, affect the entry or release of human immunodeficiency virus 1 (HIV, murine leukemia virus (MLV, or avian leukosis virus (ALV. While TRIM11 and 31 inhibited HIV entry, TRIM11 enhanced N-MLV entry by interfering with Ref1 restriction. Strikingly, many TRIM proteins affected late stages of the viral life cycle. Gene silencing of endogenously expressed TRIM 25, 31, and 62 inhibited viral release indicating that they play an important role at late stages of the viral life cycle. In contrast, downregulation of TRIM11 and 15 enhanced virus release suggesting that these proteins contribute to the endogenous restriction of retroviruses in cells.

  15. Application of the Integrated Safety Assessment methodology to safety margins. Dynamic Event Trees, Damage Domains and Risk Assessment

    International Nuclear Information System (INIS)

    Ibánez, L.; Hortal, J.; Queral, C.; Gómez-Magán, J.; Sánchez-Perea, M.; Fernández, I.; Meléndez, E.; Expósito, A.; Izquierdo, J.M.; Gil, J.; Marrao, H.; Villalba-Jabonero, E.

    2016-01-01

    The Integrated Safety Assessment (ISA) methodology, developed by the Consejo de Seguridad Nuclear, has been applied to an analysis of Zion NPP for sequences with Loss of the Component Cooling Water System (CCWS). The ISA methodology proposal starts from the unfolding of the Dynamic Event Tree (DET). Results from this first step allow assessing the sequence delineation of standard Probabilistic Safety Analysis results. For some sequences of interest of the outlined DET, ISA then identifies the Damage Domain (DD). This is the region of uncertain times and/or parameters where a safety limit is exceeded, which indicates the occurrence of certain damage situation. This paper illustrates application of this concept obtained simulating sequences with MAAP and with TRACE. From information of simulation results of sequence transients belonging to the DD and the time-density probability distributions of the manual actions and of occurrence of stochastic phenomena, ISA integrates the dynamic reliability equations proposed to obtain the sequence contribution to the global Damage Exceedance Frequency (DEF). Reported results show a slight increase in the DEF for sequences investigated following a power uprate from 100% to 110%. This demonstrates the potential use of the method to help in the assessment of design modifications. - Highlights: • This paper illustrates an application of the ISA methodology to safety margins. • Dynamic Event Trees are useful tool for verifying the standard PSA Event Trees. • The ISA methodology takes into account the uncertainties in human action times. • The ISA methodology shows the Damage Exceedance Frequency increase in power uprates.

  16. Application of Master Curve Methodology for Structural Integrity Assessments of Nuclear Components

    Energy Technology Data Exchange (ETDEWEB)

    Sattari-Far, Iradj [Det Norske Veritas, Stockholm (Sweden); Wallin, Kim [VTT, Esbo (Finland)

    2005-10-15

    The objective was to perform an in-depth investigation of the Master Curve methodology and also based on this method develop a procedure for fracture assessments of nuclear components. The project has sufficiently illustrated the capabilities of the Master Curve methodology for fracture assessments of nuclear components. Within the scope of this work, the theoretical background of the methodology and its validation on small and large specimens has been studied and presented to a sufficiently large extent, as well as the correlations between the charpy-V data and the Master Curve T{sub 0} reference temperature in the evaluation of fracture toughness. The work gives a comprehensive report of the background theory and the different applications of the Master Curve methodology. The main results of the work have shown that the cleavage fracture toughness is characterized by a large amount of statistical scatter in the transition region, it is specimen size dependent and it should be treated statistically rather than deterministically. The Master Curve methodology is able to make use of statistical data in a consistent way. Furthermore, the Master Curve methodology provides a more precise prediction of the fracture toughness of embrittled materials in comparison with the ASME K{sub IC} reference curve, which often gives over-conservative results. The suggested procedure in this study, concerning the application of the Master Curve method in fracture assessments of ferritic steels in the transition region and the low shelf regions, is valid for the temperatures range T{sub 0}-50{<=}T{<=}T{sub 0}+50 deg C. If only approximate information is required, the Master Curve may well be extrapolated outside this temperature range. The suggested procedure has also been illustrated for some examples.

  17. TechIP: A Methodology for Emerging Information Technology Insertion & Integration

    National Research Council Canada - National Science Library

    Patel, Has

    2004-01-01

    ...) processing and software agents. To implement these requirements, the system designers are required to insert, integrate and manage proven advances in Emerging Information Technology (EIT) in to the...

  18. Compensation of the AKT signaling by ERK signaling in transgenic mice hearts overexpressing TRIM72

    International Nuclear Information System (INIS)

    Ham, Young-Mi; Mahoney, Sarah Jane

    2013-01-01

    The AKT and ERK signaling pathways are known to be involved in cell hypertrophy, proliferation, survival and differentiation. Although there is evidence for crosstalk between these two signaling pathways in cellulo, there is less evidence for cross talk in vivo. Here, we show that crosstalk between AKT and ERK signaling in the hearts of TRIM72-overexpressing transgenic mice (TRIM72-Tg) with alpha-MHC promoter regulates and maintains their heart size. TRIM72, a heart- and skeletal muscle-specific protein, downregulates AKT-mTOR signaling via IRS-1 degradation and reduces the size of rat cardiomyocytes and the size of postnatal TRIM72-Tg hearts. TRIM72 expression was upregulated by hypertrophic inducers in cardiomyocytes, while IRS-1 was downregulated by IGF-1. TRIM72 specifically regulated IGF-1-dependent AKT-mTOR signaling, resulting in a reduction of the size of cardiomyocytes. Postnatal TRIM72-Tg hearts were smaller than control-treated hearts with inhibition of AKT-mTOR signaling. However, adult TRIM72-Tg hearts were larger than of control despite the suppression of AKT-mTOR signaling. Activation of ERK, PKC-α, and JNK were observed to be elevated in adult TRIM72-Tg, and these signals were mediated by ET-1 via the ET receptors A and B. Altogether, these results suggest that AKT signaling regulates cardiac hypertrophy in physiological conditions, and ERK signaling compensates for the absence of AKT signaling during TRIM72 overexpression, leading to pathological hypertrophy. -- Highlights: • TRIM72 inhibits AKT signaling through ubiquitination of IRS-1 in cardiac cells. • TRIM72 regulates the size of cardiac cells. • TRIM72 regulates size of postnatal TRIM72-overexpressing transgenic mice hearts. • Adult TRIM72-overexpressing transgenic mice hearts showed cardiac dysfunction. • Adult TRIM72 transgenic mice hearts showed higher expression of endothelin receptors

  19. Compensation of the AKT signaling by ERK signaling in transgenic mice hearts overexpressing TRIM72

    Energy Technology Data Exchange (ETDEWEB)

    Ham, Young-Mi, E-mail: youngmi_ham@hms.harvard.edu [College of Life Science and Biotechnology, Korea University, Seoul (Korea, Republic of); Department of Cell Biology, Harvard Medical School, Boston, MA 02115 (United States); Mahoney, Sarah Jane [Department of Cell Biology, Harvard Medical School, Boston, MA 02115 (United States)

    2013-06-10

    The AKT and ERK signaling pathways are known to be involved in cell hypertrophy, proliferation, survival and differentiation. Although there is evidence for crosstalk between these two signaling pathways in cellulo, there is less evidence for cross talk in vivo. Here, we show that crosstalk between AKT and ERK signaling in the hearts of TRIM72-overexpressing transgenic mice (TRIM72-Tg) with alpha-MHC promoter regulates and maintains their heart size. TRIM72, a heart- and skeletal muscle-specific protein, downregulates AKT-mTOR signaling via IRS-1 degradation and reduces the size of rat cardiomyocytes and the size of postnatal TRIM72-Tg hearts. TRIM72 expression was upregulated by hypertrophic inducers in cardiomyocytes, while IRS-1 was downregulated by IGF-1. TRIM72 specifically regulated IGF-1-dependent AKT-mTOR signaling, resulting in a reduction of the size of cardiomyocytes. Postnatal TRIM72-Tg hearts were smaller than control-treated hearts with inhibition of AKT-mTOR signaling. However, adult TRIM72-Tg hearts were larger than of control despite the suppression of AKT-mTOR signaling. Activation of ERK, PKC-α, and JNK were observed to be elevated in adult TRIM72-Tg, and these signals were mediated by ET-1 via the ET receptors A and B. Altogether, these results suggest that AKT signaling regulates cardiac hypertrophy in physiological conditions, and ERK signaling compensates for the absence of AKT signaling during TRIM72 overexpression, leading to pathological hypertrophy. -- Highlights: • TRIM72 inhibits AKT signaling through ubiquitination of IRS-1 in cardiac cells. • TRIM72 regulates the size of cardiac cells. • TRIM72 regulates size of postnatal TRIM72-overexpressing transgenic mice hearts. • Adult TRIM72-overexpressing transgenic mice hearts showed cardiac dysfunction. • Adult TRIM72 transgenic mice hearts showed higher expression of endothelin receptors.

  20. An integrative approach to the design methodology for 3-phase power conditioners in Photovoltaic Grid-Connected systems

    International Nuclear Information System (INIS)

    Rey-Boué, Alexis B.; García-Valverde, Rafael; Ruz-Vila, Francisco de A.; Torrelo-Ponce, José M.

    2012-01-01

    Highlights: ► A design methodology for Photovoltaic grid-connected systems is presented. ► Models of the Photovoltaic Generator and the 3-phase Inverter are described. ► The power factor and the power quality are regulated with vector control. ► Simulation and experimental results validate the design methodology. ► The proposed methodology can be extended to any Renewable or Industrial System. - Abstract: A novel methodology is presented in this paper, for the design of the Power and Control Subsystems of a 3-phase Photovoltaic Grid-Connected system in an easy and comprehensive way, as an integrative approach. At the DC side of the Power Subsystem, the Photovoltaic Generator modeling is revised and a simple model is proposed, whereas at the AC side, a vector analysis is done to deal with the instantaneous 3-phase variables of the grid-connected Voltage Source Inverter. A d–q control approach is established in the Control Subsystem, along with its specific tuned parameters, as a vector control alternative which will allow the decoupled control of the instantaneous active and reactive powers. A particular Case of Study is presented to illustrate the behavior of the design methodology regarding the fulfillment of the Photovoltaic plant specifications. Some simulations are run to study the performance of the Photovoltaic Generator together with the exerted d–q control to the grid-connected 3-phase inverter, and some experimental results, obtained from a built flexible platform, are also shown. The simulations and the experimental results validate the overall performance of the 3-phase Photovoltaic Grid-Connected system due to the attained unitary power factor operation together with good power quality. The final validation of the proposed design methodology is also achieved.

  1. A Computer-Based System Integrating Instruction and Information Retrieval: A Description of Some Methodological Considerations.

    Science.gov (United States)

    Selig, Judith A.; And Others

    This report, summarizing the activities of the Vision Information Center (VIC) in the field of computer-assisted instruction from December, 1966 to August, 1967, describes the methodology used to load a large body of information--a programed text on basic opthalmology--onto a computer for subsequent information retrieval and computer-assisted…

  2. A food quality management research methodology integrating technological and managerial theories

    NARCIS (Netherlands)

    Luning, P.A.; Marcelis, W.J.

    2009-01-01

    In this article it is argued how the complexity of food quality management combined with the high requirements on food quality requires a specific research methodology. It is concluded that food quality management research has to deal with two quite different paradigms, the one from technological

  3. Design of integrated autopilot/autothrottle for NASA TSRV airplane using integral LQG methodology. [transport systems research vehicle

    Science.gov (United States)

    Kaminer, Isaac; Benson, Russell A.

    1989-01-01

    An integrated autopilot/autothrottle control system has been developed for the NASA transport system research vehicle using a two-degree-of-freedom approach. Based on this approach, the feedback regulator was designed using an integral linear quadratic regulator design technique, which offers a systematic approach to satisfy desired feedback performance requirements and guarantees stability margins in both control and sensor loops. The resulting feedback controller was discretized and implemented using a delta coordinate concept, which allows for transient free controller switching by initializing all controller states to zero and provides a simple solution for dealing with throttle limiting cases.

  4. Robust estimators based on generalization of trimmed mean

    Czech Academy of Sciences Publication Activity Database

    Adam, Lukáš; Bejda, P.

    (2018) ISSN 0361-0918 Institutional support: RVO:67985556 Keywords : Breakdown point * Estimators * Geometric median * Location * Trimmed mean Subject RIV: BA - General Mathematics Impact factor: 0.457, year: 2016 http://library.utia.cas.cz/separaty/2017/MTR/adam-0481224.pdf

  5. Influence of an accurate trimming operation on springback

    NARCIS (Netherlands)

    Avetisyan, Marianna; Meinders, Vincent T.; Huetink, Han

    2006-01-01

    When a sheet metal forming operation, such as deep drawing, is followed by a trimming operation the numerical springback is influenced by various physical parameters and numerical factors. Two techniques of taking into the account the stress state change due to cutting in the FE plate model are

  6. TRIM timber projections: an evaluation based on forest inventory measurements.

    Science.gov (United States)

    John R. Mills

    1989-01-01

    Two consecutive timberland inventories collected from permanent plots in the natural pine type in North Carolina were used to evaluate the timber resource inventory model (TRIM). This study compares model predictions with field measurements and examines the effect of inventory data aggregation on the accuracy of projections. Projections were repeated for two geographic...

  7. Prognostic indicators and the importance of trimming in noninfective ...

    African Journals Online (AJOL)

    Prognostic indicators and the importance of trimming in noninfective claw disorders in cattle. ... features of chronic laminitis occurred concurrently with heel or sole erosion, white line separation, sole ulcers, horizontal hoof wall fissures and double soles. In most smallholder farms, cows with these disorders were neglected to ...

  8. 33 CFR 401.30 - Ballast water and trim.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Ballast water and trim. 401.30... OF TRANSPORTATION SEAWAY REGULATIONS AND RULES Regulations Seaway Navigation § 401.30 Ballast water... exclusive economic zone must agree to comply with the “Code of Best Practices for Ballast Water Management...

  9. Methodology to translate policy assessment problems into scenarios: the example of the SEAMLESS integrated framework

    NARCIS (Netherlands)

    Therond, O.; Belhouchette, H.; Janssen, S.J.C.; Louhichi, K.; Ewert, F.; Bergez, J.E.; Wery, J.; Heckelei, T.; Olsson, J.A.; Leenhardt, D.; Ittersum, van M.K.

    2009-01-01

    Scenario-based approaches in environmental and policy assessment studies are increasingly applied within integrated assessment and modelling frameworks. The SEAMLESS project develops such an integrated framework (SEAMLESS-IF) aiming to assess, ex-ante, impacts of alternative agro-environmental

  10. Integrating Ethics into International Business Teaching: Challenges and Methodologies in the Greater China Context

    Science.gov (United States)

    Whitla, Paul

    2011-01-01

    This paper examines the process of integrating ethics into the teaching of international business within the Greater China region. An example of how ethics is integrated into a required undergraduate international business course at a Hong Kong based university is presented. The contextual challenges of developing a course for use in the Greater…

  11. Benefits of using an optimization methodology for identifying robust process integration investments under uncertainty-A pulp mill example

    International Nuclear Information System (INIS)

    Svensson, Elin; Berntsson, Thore; Stroemberg, Ann-Brith

    2009-01-01

    This paper presents a case study on the optimization of process integration investments in a pulp mill considering uncertainties in future electricity and biofuel prices and CO 2 emissions charges. The work follows the methodology described in Svensson et al. [Svensson, E., Berntsson, T., Stroemberg, A.-B., Patriksson, M., 2008b. An optimization methodology for identifying robust process integration investments under uncertainty. Energy Policy, in press, (doi:10.1016/j.enpol.2008.10.023)] where a scenario-based approach is proposed for the modelling of uncertainties. The results show that the proposed methodology provides a way to handle the time dependence and the uncertainties of the parameters. For the analyzed case, a robust solution is found which turns out to be a combination of two opposing investment strategies. The difference between short-term and strategic views for the investment decision is analyzed and it is found that uncertainties are increasingly important to account for as a more strategic view is employed. Furthermore, the results imply that the obvious effect of policy instruments aimed at decreasing CO 2 emissions is, in applications like this, an increased profitability for all energy efficiency investments, and not as much a shift between different alternatives

  12. Benefits of using an optimization methodology for identifying robust process integration investments under uncertainty-A pulp mill example

    Energy Technology Data Exchange (ETDEWEB)

    Svensson, Elin [Department of Energy and Environment, Division of Heat and Power Technology, Chalmers University of Technology, SE-412 96 Goeteborg (Sweden)], E-mail: elin.svensson@chalmers.se; Berntsson, Thore [Department of Energy and Environment, Division of Heat and Power Technology, Chalmers University of Technology, SE-412 96 Goeteborg (Sweden); Stroemberg, Ann-Brith [Fraunhofer-Chalmers Research Centre for Industrial Mathematics, Chalmers Science Park, SE-412 88 Gothenburg (Sweden)

    2009-03-15

    This paper presents a case study on the optimization of process integration investments in a pulp mill considering uncertainties in future electricity and biofuel prices and CO{sub 2} emissions charges. The work follows the methodology described in Svensson et al. [Svensson, E., Berntsson, T., Stroemberg, A.-B., Patriksson, M., 2008b. An optimization methodology for identifying robust process integration investments under uncertainty. Energy Policy, in press, (doi:10.1016/j.enpol.2008.10.023)] where a scenario-based approach is proposed for the modelling of uncertainties. The results show that the proposed methodology provides a way to handle the time dependence and the uncertainties of the parameters. For the analyzed case, a robust solution is found which turns out to be a combination of two opposing investment strategies. The difference between short-term and strategic views for the investment decision is analyzed and it is found that uncertainties are increasingly important to account for as a more strategic view is employed. Furthermore, the results imply that the obvious effect of policy instruments aimed at decreasing CO{sub 2} emissions is, in applications like this, an increased profitability for all energy efficiency investments, and not as much a shift between different alternatives.

  13. Benefits of using an optimization methodology for identifying robust process integration investments under uncertainty. A pulp mill example

    Energy Technology Data Exchange (ETDEWEB)

    Svensson, Elin; Berntsson, Thore [Department of Energy and Environment, Division of Heat and Power Technology, Chalmers University of Technology, SE-412 96 Goeteborg (Sweden); Stroemberg, Ann-Brith [Fraunhofer-Chalmers Research Centre for Industrial Mathematics, Chalmers Science Park, SE-412 88 Gothenburg (Sweden)

    2009-03-15

    This paper presents a case study on the optimization of process integration investments in a pulp mill considering uncertainties in future electricity and biofuel prices and CO{sub 2} emissions charges. The work follows the methodology described in Svensson et al. [Svensson, E., Berntsson, T., Stroemberg, A.-B., Patriksson, M., 2008b. An optimization methodology for identifying robust process integration investments under uncertainty. Energy Policy, in press, doi:10.1016/j.enpol.2008.10.023] where a scenario-based approach is proposed for the modelling of uncertainties. The results show that the proposed methodology provides a way to handle the time dependence and the uncertainties of the parameters. For the analyzed case, a robust solution is found which turns out to be a combination of two opposing investment strategies. The difference between short-term and strategic views for the investment decision is analyzed and it is found that uncertainties are increasingly important to account for as a more strategic view is employed. Furthermore, the results imply that the obvious effect of policy instruments aimed at decreasing CO{sub 2} emissions is, in applications like this, an increased profitability for all energy efficiency investments, and not as much a shift between different alternatives. (author)

  14. The Timber Resource Inventory Model (TRIM): a projection model for timber supply and policy analysis.

    Science.gov (United States)

    P.L. Tedder; R.N. La Mont; J.C. Kincaid

    1987-01-01

    TRIM (Timber Resource Inventory Model) is a yield table projection system developed for timber supply projections and policy analysis. TRIM simulates timber growth, inventories, management and area changes, and removals over the projection period. Programs in the TRIM system, card-by-card descriptions of required inputs, table formats, and sample results are presented...

  15. Research on the Special Railway Intelligence Transportation Hierarchy and System Integration Methodology

    Directory of Open Access Journals (Sweden)

    Meng-Jie WANG

    2013-05-01

    Full Text Available Following the rapid development of information technology in the field of railway transportation, the problems of establishing a digital, integrated and intelligent special railway system need to be solved immediately. This paper designs and implements the intelligent transportation information system based on the unique pattern of transportation organization, the characteristics of transportation operations and the workflow of special railway. Through the detailed analysis of system architecture and framework design, the main subsystems and the internal comprehensive integrated principle, business system from a system integration perspective of the special railway is optimized, which can be able to realize the integration of all kinds of information resources. The implementation of integration and the special railway intelligent system is a great change in terms of maximizing transportation capacity, improving efficiency and guaranteeing the safety of special railway transportation.

  16. Use of neutron diffraction and laser-induced plasma spectroscopy in integrated authentication methodologies of copper alloy artefacts

    International Nuclear Information System (INIS)

    Siano, S.; Bartol, L.; Mencaglia, A.A.; Agresti, J.; Miccio, M.

    2009-01-01

    The present study approaches the general problem of the authentication of copper alloy artefacts of art and historical interest using non-invasive analytical techniques. It aims to demonstrate that a suitable combination of time-of-flight neutron diffraction and laser-induced plasma spectroscopy in integrated multidisciplinary authentication methodologies can provide crucial data for discriminating between genuine archaeological objects and modern counterfeits. After introducing the methodology, which is dedicated in particular to copper alloy figurines of ancient style, two representative authentication case studies are discussed. The results of the work provide evidence that the combination of multiphase analysis using TOF-N D and elemental depth profiles provided by Lips makes it possible to solve most of the present authentication problems.

  17. Comparative economic analysis of the Integral Molten Salt Reactor and an advanced PWR using the G4-ECONS methodology

    International Nuclear Information System (INIS)

    Samalova, Ludmila; Chvala, Ondrej; Maldonado, G. Ivan

    2017-01-01

    The assessment of economic viability of a new reactor concept is crucial particularly during the early stages of its concept development. The G4-ECONS methodology provides a standardized top-down estimate of electricity cost and parametric sensitivities, not specifically targeted toward an accurate prediction of the final cost when deployed, but rather seeking an approximation of cost variations relative to other systems. This study presents an analysis of the Integral Molten Salt Reactor (IMSR) concept in comparison with a consistent analysis of an advanced PWR reactor (represented by AP1000). Estimation of levelized unit electricity costs, as well as sensitivity analyses to the discount rate and uranium or SWU prices, are presented using this methodology.

  18. Development of a standard methodology for integrating non-food crop production in rural areas with niche energy markets. Proceedings

    International Nuclear Information System (INIS)

    1996-09-01

    This project was supported as a Concerted Action under the EC DGVI AIR programme from 1993-1996. It has successfully developed a standard methodology to help integrate non-food crop production in rural areas with niche energy markets. The methodology was used to compare the costs of different energy crop production and conversion options across the six participating nations. The partners provide a representative cross-section of European agriculture and energy expertise. All partners agreed on three niche markets favourable for biomass and biofuels: small-scale heat markets (less than 1 MW th ) for agro-industry, domestic and commercial buildings, medium-scale heat markets (1-10MW th ), including cogeneration for light industry and district heating, and liquid biofuels as substitutes for fossil fuels in transport, heat and power applications. (Author)

  19. Methodologies of health impact assessment as part of an integrated approach to reduce effects of air pollution

    Energy Technology Data Exchange (ETDEWEB)

    Aunan, K; Seip, H M

    1995-12-01

    Quantification of average frequencies of health effects on a population level is an essential part of an integrated assessment of pollution effects. Epidemiological studies seem to provide the best basis for such estimates. This paper gives an introduction to a methodology for health impact assessment and also the results from selected parts of a case study in Hungary. This case study is aimed at testing and improving the methodology for integrated assessment and focuses on energy production and consumption and implications for air pollution. Using monitoring data from Budapest, the paper gives estimates of excess frequencies of respiratory illness, mortality and other health end-points. For a number of health end-points, particles probably may serve as a good indicator component. Stochastic simulation is used to illustrate the uncertainties imbedded in the exposure-response function applied. The paper uses the ``bottom up approach`` to find cost-effective abatement strategies against pollution damages, where specific abatement measures such as emission standards for vehicles are explored in detail. It is concluded that in spite of large uncertainties in every step of the analysis, an integrated assessment of costs and benefits of different abatement measures is valuable as it clarifies the main objectives of an abatement policy and explicitly describes the adverse impacts of different activities and their relative importance. 46 refs., 11 figs., 2 tabs.

  20. Integrating Ontology Debugging and Matching into the eXtreme Design Methodology

    OpenAIRE

    Dragisic, Zlatan; Lambrix, Patrick; Blomqvist, Eva

    2015-01-01

    Ontology design patterns (ODPs) and related ontology development methodologies were designed as ways of sharing and reusing best practices in ontology engineering. However, while the use of these reduces the number of issues in the resulting ontologies defects can still be introduced into the ontology due to improper use or misinterpretation of the patterns. Thus, the quality of the developed ontologies is still a major concern. In this paper we address this issue by describing how ontology d...

  1. 76 FR 72978 - Premier Trim, LLC, Spectrum Trim, LLC and Grant Products International, Inc. D/B/A Spectrum Grant...

    Science.gov (United States)

    2011-11-28

    ..., Spectrum Trim, LLC and Grant Products International, Inc. D/B/A Spectrum Grant De Mexico Including Workers Whose Unemployment Insurance (UI) Wages Are Paid Through Grant Products International, Inc... Brownsville, TX; Amended Certification Regarding Eligibility To Apply for Worker Adjustment Assistance In...

  2. An engineering methodology for implementing and testing VLSI (Very Large Scale Integrated) circuits

    Science.gov (United States)

    Corliss, Walter F., II

    1989-03-01

    The engineering methodology for producing a fully tested VLSI chip from a design layout is presented. A 16-bit correlator, NPS CORN88, that was previously designed, was used as a vehicle to demonstrate this methodology. The study of the design and simulation tools, MAGIC and MOSSIM II, was the focus of the design and validation process. The design was then implemented and the chip was fabricated by MOSIS. This fabricated chip was then used to develop a testing methodology for using the digital test facilities at NPS. NPS CORN88 was the first full custom VLSI chip, designed at NPS, to be tested with the NPS digital analysis system, Tektronix DAS 9100 series tester. The capabilities and limitations of these test facilities are examined. NPS CORN88 test results are included to demonstrate the capabilities of the digital test system. A translator, MOS2DAS, was developed to convert the MOSSIM II simulation program to the input files required by the DAS 9100 device verification software, 91DVS. Finally, a tutorial for using the digital test facilities, including the DAS 9100 and associated support equipments, is included as an appendix.

  3. Methodology for Selecting Best Management Practices Integrating Multiple Stakeholders and Criteria. Part 2: Case Study

    Directory of Open Access Journals (Sweden)

    Mauricio Carvallo Aceves

    2016-02-01

    Full Text Available The selection of stormwater Best Management Practices (BMPs for mitigating the effects of urbanization on the hydrological cycle could be a complex process due to conflicting stakeholder views, and varying levels of performance of BMPs across a range of criteria (runoff reduction, erosion control, etc.. Part 1 of this article proposed a methodology based on the application of multi-criteria decision aid (MCDA methods, which was tested here on a residential stormwater network in the Montreal area. The case study considered green roofs, rain gardens, rain barrels and pervious pavement over a range of economic, social, and water quality and quantity criteria by applying 4 MCDA methods under three different stakeholder views. The results indicated Elimination et Choix Traduisant la Réalité (ELECTRE III to be the most appropriate method for the methodology, presenting flexibility concerning threshold values, criteria weights, and showing shared top choices across stakeholders (rain gardens, and rain gardens in combination with pervious pavement. The methodology shows potential for more formal applications and research opportunities. Future work may lie in the inclusion of multiple objective optimization, better stakeholder engagement, estimation of economic benefits, water quality modeling, long-term hydrological simulations, and estimating real BMP pollutant removal rates.

  4. Integrated methodology for production related risk management of vehicle electronics (IMPROVE)

    OpenAIRE

    Geis, Stefan Rafael

    2006-01-01

    This scientific work is designated to provide an innovative and integrated conceptional approach to improve the assembly quality of automotive electronics. This is achieved by the reduction and elimination of production related risks of automotive electronics and the implementation of a sustainable solution process. The focus is the development and implementation of an integrated technical risk management approach for automotive electronics throughout the vehicle life cycle and the vehicle pr...

  5. Considering axiological integrity: a methodological analysis of qualitative evidence syntheses, and its implications for health professions education.

    Science.gov (United States)

    Kelly, Martina; Ellaway, Rachel H; Reid, Helen; Ganshorn, Heather; Yardley, Sarah; Bennett, Deirdre; Dornan, Tim

    2018-05-14

    Qualitative evidence synthesis (QES) is a suite of methodologies that combine qualitative techniques with the synthesis of qualitative knowledge. They are particularly suited to medical education as these approaches pool findings from original qualitative studies, whilst paying attention to context and theoretical development. Although increasingly sophisticated use is being made of qualitative primary research methodologies in health professions education (HPE) the use of secondary qualitative reviews in HPE remains underdeveloped. This study examined QES methods applied to clinical humanism in healthcare as a way of advancing thinking around the use of QES in HPE in general. A systematic search strategy identified 49 reviews that fulfilled the inclusion criteria. Meta-study was used to develop an analytic summary of methodological characteristics, the role of theory, and the synthetic processes used in QES reviews. Fifteen reviews used a defined methodology, and 17 clearly explained the processes that led from data extraction to synthesis. Eight reviews adopted a specific theoretical perspective. Authors rarely described their reflexive relationship with their data. Epistemological positions tended to be implied rather than explicit. Twenty-five reviews included some form of quality appraisal, although it was often unclear how authors acted on its results. Reviewers under-reported qualitative approaches in their review methodologies, and tended to focus on elements such as systematicity and checklist quality appraisal that were more germane to quantitative evidence synthesis. A core concern was that the axiological (value) dimensions of the source materials were rarely considered let alone accommodated in the synthesis techniques used. QES can be used in HPE research but only with careful attention to maintaining axiological integrity.

  6. Proposition of a modeling and an analysis methodology of integrated reverse logistics chain in the direct chain

    Energy Technology Data Exchange (ETDEWEB)

    Mimouni, F.; Abouabdellah, A.

    2016-07-01

    Propose a modeling and analysis methodology based on the combination of Bayesian networks and Petri networks of the reverse logistics integrated the direct supply chain. Network modeling by combining Petri and Bayesian network. Modeling with Bayesian network complimented with Petri network to break the cycle problem in the Bayesian network. Demands are independent from returns. Model can only be used on nonperishable products. Legislation aspects: Recycling laws; Protection of environment; Client satisfaction via after sale service. Bayesian network with a cycle combined with the Petri Network. (Author)

  7. Criteria for quantitative and qualitative data integration: mixed-methods research methodology.

    Science.gov (United States)

    Lee, Seonah; Smith, Carrol A M

    2012-05-01

    Many studies have emphasized the need and importance of a mixed-methods approach for evaluation of clinical information systems. However, those studies had no criteria to guide integration of multiple data sets. Integrating different data sets serves to actualize the paradigm that a mixed-methods approach argues; thus, we require criteria that provide the right direction to integrate quantitative and qualitative data. The first author used a set of criteria organized from a literature search for integration of multiple data sets from mixed-methods research. The purpose of this article was to reorganize the identified criteria. Through critical appraisal of the reasons for designing mixed-methods research, three criteria resulted: validation, complementarity, and discrepancy. In applying the criteria to empirical data of a previous mixed methods study, integration of quantitative and qualitative data was achieved in a systematic manner. It helped us obtain a better organized understanding of the results. The criteria of this article offer the potential to produce insightful analyses of mixed-methods evaluations of health information systems.

  8. Methodology for the integral comparison of nuclear reactors: selecting a reactor for Mexico

    International Nuclear Information System (INIS)

    Reyes R, R.; Martin del Campo M, C.

    2006-01-01

    In this work it was built a methodology to compare nuclear reactors of third generation that can be contemplated for future electric planning in Mexico. This methodology understands the selection of the reactors to evaluate eliminating the reactors that still are not sufficiently mature at this time of the study. A general description of each reactor together with their main ones characteristic is made. It was carried out a study for to select the group of parameters that can serve as evaluation indicators, which are the characteristics of the reactors with specific values for each considered technology, and it was elaborated an evaluation matrix indicators including the reactors in the columns and those indicators in the lines. Since that none reactor is the best in all the indicators were necessary to use a methodology for multi criteria taking decisions that we are presented. It was used the 'Fuzzy Logic' technique, the which is based in those denominated diffuse groups and in a system of diffuse inference based on heuristic rules in the way 'If Then consequence> ', where the linguistic values of the condition and of the consequence is defined by diffuse groups, it is as well as the rules always they transform a diffuse group into another. Later on they combine all the diffuse outputs to create a single output and an inverse transformation is made that it transfers the output from the diffuse domain to the real one. They were carried out two studies one with the entirety of the indicators and another in which the indicators were classified in three approaches: the first one refers to indicators related with the planning of the plants inside the context of the general electric sector, the second approach includes indicators related with the characteristics of the fuel and the third it considers indicators related with the acting of the plant in safety and environmental impact. This second study allowed us to know the qualities of each reactor in each one of the

  9. Mixed methods in psychotherapy research: A review of method(ology) integration in psychotherapy science.

    Science.gov (United States)

    Bartholomew, Theodore T; Lockard, Allison J

    2018-06-13

    Mixed methods can foster depth and breadth in psychological research. However, its use remains in development in psychotherapy research. Our purpose was to review the use of mixed methods in psychotherapy research. Thirty-one studies were identified via the PRISMA systematic review method. Using Creswell & Plano Clark's typologies to identify design characteristics, we assessed each study for rigor and how each used mixed methods. Key features of mixed methods designs and these common patterns were identified: (a) integration of clients' perceptions via mixing; (b) understanding group psychotherapy; (c) integrating methods with cases and small samples; (d) analyzing clinical data as qualitative data; and (e) exploring cultural identities in psychotherapy through mixed methods. The review is discussed with respect to the value of integrating multiple data in single studies to enhance psychotherapy research. © 2018 Wiley Periodicals, Inc.

  10. Multi-Layer Integration Methodology for development of ICT competences in SMEs

    DEFF Research Database (Denmark)

    Nunez, Heilyn Camacho

    2013-01-01

    (ICT) is a challenge for many small and medium-sized enterprises (SMEs). As it is clear the important role of the SMEs for the countries development, this paper proposes a methodology that aims to interconnect external forces that can facilitate the removal or mitigation of some of the constraints......To modern enterprises, information technology has a multi-value, such as improving products, customer satisfaction and quality; it also facilitates administrative processes, reduces cost and improves competitiveness, among other things. Taking advantage of information and communication technologies...

  11. Building an integrated methodology of learning that can optimally support improvements in healthcare.

    Science.gov (United States)

    Lynn, Joanne

    2011-04-01

    The methods for healthcare reform are strikingly underdeveloped, with much reliance on political power. A methodology that combined methods from sources such as clinical trials, experience-based wisdom, and improvement science could be among the aims of the upcoming work in the USA on comparative effectiveness and on the agenda of the Center for Medicare and Medicaid Innovation in the Centers for Medicare and Medicaid Services. Those working in quality improvement have an unusual opportunity to generate substantial input into these processes through professional organisations such as the Academy for Healthcare Improvement and dominant leadership organisations such as the Institute for Healthcare Improvement.

  12. A Methodology to Integrate Security and Cost-effectiveness in ATM

    Directory of Open Access Journals (Sweden)

    Francesca Matarese

    2014-01-01

    prioritizing the threats and proposing cost-effective countermeasures for the weaknesses found. ATM security is concerned with securing ATM assets in order to prevent threats and limit their effects on the overall aviation network. This effect limitation can be achieved by removing the vulnerability from the system and/or increasing the tolerance in case of component failures due to attacks. The security risk assessment methodology proposed is based on what is currently being done by the industry (the International Civil Aviation Organization (ICAO and the International Standard Organization (ISO, etc..

  13. MEAPA - Integrated methodology for alternative energy sources map pin in the State of Para - Brazil; MEAPA - Metodologias integradas para o mapeamento de energias alternativas no Estado do Para

    Energy Technology Data Exchange (ETDEWEB)

    Monteiro, Claudio; Lopes, J. Pecas; Va, Kowk P.; Herold, Helmut [Instituto de Engenharia de Sistemas e Computadores (INESC), Porto (Portugal). Power System Unit. E-mail: cmonteiro@inescn.pt; Rocha, Brigida; Pinheiro, Helten; Rocha, Olavo [Para Univ., Belem, PA (Brazil). Dept. de Engenharia Eletrica. E-mail: rocha@interconect.com.br; Silva, Isa O. [Para Univ., Belem, PA (Brazil). Dept. de Meteorologia; Moraes, Sinfronio [Para Univ., Belem, PA (Brazil). Dept. de Mecanica

    1999-07-01

    This paper describes the MEAPA project for the development of methodologies which support the renewable energy sources integration in the Marajo island - Para - Brazil. The methodologies used will be described including the construction of a geographical database, renewable resources (wind, solar and biomass) mapping, transport costs, cost of electric power produced by various systems and electrification sceneries and comparison of electrification solutions.

  14. Nursing home staff members' subjective frames of reference on residents' achievement of ego integrity: A Q-methodology study.

    Science.gov (United States)

    Lim, Sun-Young; Chang, Sung-Ok

    2018-01-01

    To discover the structure of the frames of reference for nursing home staff members' subjective judgment of residents' achievement of ego integrity. Q-methodology was applied. Twenty-eight staff members who were working in a nursing home sorted 34 Q-statements into the shape of a normal distribution. A centroid factor analysis and varimax rotation, using the PQ-method program, revealed four factors: identifying clues to residents' positive acceptance of their whole life span, identifying residents' ways of enjoying their current life, referencing residents' attitudes and competencies toward harmonious relationships, and identifying residents' integrated efforts to establish self-esteem. These subjective frames of reference need to be investigated in order to improve the relationships with nursing home residents and their quality of life. Consequently, the fundamental monitoring tools to help staff members make subjective judgments can be formed. © 2017 Japan Academy of Nursing Science.

  15. Integrating cost information with health management support system: an enhanced methodology to assess health care quality drivers.

    Science.gov (United States)

    Kohli, R; Tan, J K; Piontek, F A; Ziege, D E; Groot, H

    1999-08-01

    Changes in health care delivery, reimbursement schemes, and organizational structure have required health organizations to manage the costs of providing patient care while maintaining high levels of clinical and patient satisfaction outcomes. Today, cost information, clinical outcomes, and patient satisfaction results must become more fully integrated if strategic competitiveness and benefits are to be realized in health management decision making, especially in multi-entity organizational settings. Unfortunately, traditional administrative and financial systems are not well equipped to cater to such information needs. This article presents a framework for the acquisition, generation, analysis, and reporting of cost information with clinical outcomes and patient satisfaction in the context of evolving health management and decision-support system technology. More specifically, the article focuses on an enhanced costing methodology for determining and producing improved, integrated cost-outcomes information. Implementation issues and areas for future research in cost-information management and decision-support domains are also discussed.

  16. TRIM5α association with cytoplasmic bodies is not required for antiretroviral activity

    International Nuclear Information System (INIS)

    Song, Byeongwoon; Diaz-Griffero, Felipe; Park, Do Hyun; Rogers, Thomas; Stremlau, Matthew; Sodroski, Joseph

    2005-01-01

    The tripartite motif (TRIM) protein, TRIM5α, restricts infection by particular retroviruses. Many TRIM proteins form cytoplasmic bodies of unknown function. We investigated the relationship between cytoplasmic body formation and the structure and antiretroviral activity of TRIM5α. In addition to diffuse cytoplasmic staining, the TRIM5α proteins from several primate species were located in cytoplasmic bodies of different sizes; by contrast, TRIM5α from spider monkeys did not form cytoplasmic bodies. Despite these differences, all of the TRIM5α proteins exhibited the ability to restrict infection by particular retroviruses. Treatment of cells with geldanamycin, an Hsp90 inhibitor, resulted in disappearance or reduction of the TRIM5α-associated cytoplasmic bodies, yet exerted little effect on the restriction of retroviral infection. Studies of green fluorescent protein-TRIM5α fusion proteins indicated that no TRIM5α domain is specifically required for association with cytoplasmic bodies. Apparently, the formation of cytoplasmic bodies is not required for the antiretroviral activity of TRIM

  17. A methodology for analysis of impacts of grid integration of renewable energy

    International Nuclear Information System (INIS)

    George, Mel; Banerjee, Rangan

    2011-01-01

    Present electricity grids are predominantly thermal (coal, gas) and hydro based. Conventional power planning involves hydro-thermal scheduling and merit order dispatch. In the future, modern renewables (hydro, solar and biomass) are likely to have a significant share in the power sector. This paper presents a method to analyse the impacts of renewables in the electricity grid. A load duration curve based approach has been developed. Renewable energy sources have been treated as negative loads to obtain a modified load duration curve from which capacity savings in terms of base and peak load generation can be computed. The methodology is illustrated for solar, wind and biomass power for Tamil Nadu (a state in India). The trade-offs and interaction between renewable sources are analysed. The impacts on capacity savings by varying the wind regime have also been shown. Scenarios for 2021-22 have been constructed to illustrate the methodology proposed. This technique can be useful for power planners for an analysis of renewables in future electricity grids. - Research highlights: → A new method to analyse impacts of renewables in the electricity grid. → Effects of wind, solar PV and biomass power on load duration curve and capacity savings are shown. → Illustration of intermittent renewables and their interplay for sites in India and the UK. → Future scenarios constructed for generation expansion planning with higher levels of renewable.

  18. Development of a Graphical Tool to integrate the Prometheus AEOlus methodology and Jason Platform

    Directory of Open Access Journals (Sweden)

    Rafhael CUNHA

    2017-07-01

    Full Text Available Software Engineering (SE is an area that intends to build high-quality software in a systematic way. However, traditional software engineering techniques and methods do not support the demand for developing Multiagent Systems (MAS. Therefore a new subarea has been studied, called Agent Oriented Software Engineering (AOSE. The AOSE area proposes solutions to issues related to the development of agent oriented systems. There is still no standardization in this subarea, resulting in several methodologies. Another issue of this subarea is that there are very few tools that are able to automatically generate code. In this work we propose a tool to support the Prometheus AEOlus Methodology because it provides modelling artifacts to all MAS dimensions: agents, environment, interaction, and organization. The tool supports all Prometheus AEOlus artifacts and can automatically generated code to the agent and interaction dimensions in the AgentSpeak Language, which is the language used in the Jason Platform. We have done some validations with the proposed tool and a case study is presented.

  19. Integrated methodology for the evaluation of the vulnerability of archaeological sites: the Roman Theater of Verona

    International Nuclear Information System (INIS)

    Cescatti, Elvis; Lorenzoni, Filippo; Caldon, Mauro; Modena, Claudio; Da Porto, Francesca

    2016-01-01

    The knowledge-based methodologies for assessing the structural safety and vulnerability of historical buildings are based on the application of an operational approach that is divided into several phases including historical research, the execution of non-destructive or moderately destructive investigations, monitoring and structural analysis. Monitoring is a useful tool to be used throughout the whole process of knowledge not only in the preliminary diagnosis, but also for the control of the quality and effectiveness of the interventions, in the context of appropriate conservation programs e protection of the object being studied. From this point of view, monitoring becomes essential for: (i) the evaluation of the real structural behavior and the identification of vulnerabilities, prior to the execution of any intervention; (ii) minimization and optimization of interventions, firstly by providing indications regarding those that are not necessary and / or invasive. This methodology has been recently applied and valid from the authors to an archaeological site of particular relevance: the Roman Theater of Verona. The deepening of the knowledge phase (historical analysis, survey, study of the subsoil, properties of materials), combined with the installation of a permanent monitoring system and the structural modeling, allowed to obtain a reliable assessment of the site's vulnerabilities with the aim of guaranteeing in an effective and careful protection and enhancement.

  20. A new integrative methodology for desertification studies based on magnetic and short-lived radioisotope measurements

    International Nuclear Information System (INIS)

    Oldfield, F.; Higgitt, S.R.; Maher, B.A.; Appleby, P.G.; Scoullos, M.

    1986-01-01

    The use of mineral magnetic measurements and short-lived radioisotope studies with 210 Pb and 137 Cs is discussed within the ecosystem watershed conceptual framework. Used in conjunction with geomorphological, sedimentological, palaeoecological and geochemical techniques, these methods can form the core of an integrated multidisciplinary study of desertification and erosion processes on all relevant temporal and spatial scales. 30 refs.; 4 figs

  1. Integrated watershed management: a planning methodology for construction of new dams in Ethiopia

    NARCIS (Netherlands)

    Bezuayehu, Tefera; Stroosnijder, L.

    2007-01-01

    Integrated watershed management (IWM) is emerging as an alternative to the centrally planned and sectoral approaches that currently characterize the planning process for dam construction in Ethiopia. This report clarifies the concept of IWM, and reviews the major social, environmental and economic

  2. A METHODOLOGY BASED ON AN ECOLOGICAL ECONOMY APPROACH FOR THE INTEGRATING MANAGEMENT OF THE SULPHUROUS WATER IN AN OIL REFINERY

    Directory of Open Access Journals (Sweden)

    Gabriel Orlando Lobelles Sardiñas

    2016-10-01

    Full Text Available Despite the current highly stringent international standards regulating the contaminating emissions to the environment, the Oil refinery of Cienfuegos is still generating liquid and gaseous emissions contaminating the environment. The construction of new units as part of the Refinery expansion leads to an increase of these emissions due to the lack of technologies for the reutilization of the sulphurous water. The objective of this paper is to propose a methodology for the integral management of the sulphurous residual water in the oil refining process, including the evaluation and selection of the most feasible technological variant to minimize the sulphur contamination of water and the resulting emissions during the process. The methodology is based on the ecological economy tools, allowing a comprehensible evaluation of six technological variants at the refinery of Cienfuegos. The Life Cycle Assessment was applied (ACV by its Spanish acronym, by means of the software SimaPro 7.1. It was evaluated through the Eco Speed Method, to minimize the possible uncertainty. An economic evaluation was performed, taking into account the external costs for a more comprehensive analysis, enabling, along with the ecological indicators, the selection of the best technological variant, achieving a methodology based on a comprehensive evaluation, and as a positive impact, the implementation of the chosen variant (V5, 98.27% of the process water was recovered, as well as the sulphur that recovered from 94 to 99.8 %, reducing the emissions from 12 200 to 120 mg/Nm3 as SO2.

  3. Reactor building integrity testing: A novel approach at Gentilly 2 - principles and methodology

    International Nuclear Information System (INIS)

    Collins, N.; Lafreniere, P.

    1991-01-01

    In 1987, Hydro-Quebec embarked on an ambitious development program to provide the Gentilly 2 nuclear power station with an effective, yet practical reactor building Integrity Test. The Gentilly 2 Integrity Test employs an innovative approach based on the reference volume concept. It is identified as the Temperature Compensation Method (TCM) System. This configuration has been demonstrated at both high and low test pressure and has achieved extraordinary precision in the leak rate measurement. The Gentilly 2 design allows the Integrity Test to be performed at a nominal 3 kPa(g) test pressure during an (11) hour period with the reactor at full power. The reactor building Pressure Test by comparison, is typically performed at high pressure 124 kPa(g)) in a 7 day window during an annual outage. The Integrity Test was developed with the goal of demonstrating containment availability. Specifically it was purported to detect a leak or hole in the 'bottled-up' reactor building greater in magnitude than an equivalent pipe of 25 mm diameter. However it is considered feasible that the high precision of the Gentilly 2 TCM System Integrity Test and a stable reactor building leak characteristic will constitute sufficient grounds for the reduction of the Pressure Test frequency. It is noted that only the TCM System has, to this date, allowed a relevant determination of the reactor building leak rate at a nominal test pressure of 3 kPa(g). Classical method tests at low pressure have lead to inconclusive results due to the high lack of precision

  4. Integrated HTA-FMEA/FMECA methodology for the evaluation of robotic system in urology and general surgery.

    Science.gov (United States)

    Frosini, Francesco; Miniati, Roberto; Grillone, Saverio; Dori, Fabrizio; Gentili, Guido Biffi; Belardinelli, Andrea

    2016-11-14

    The following study proposes and tests an integrated methodology involving Health Technology Assessment (HTA) and Failure Modes, Effects and Criticality Analysis (FMECA) for the assessment of specific aspects related to robotic surgery involving safety, process and technology. The integrated methodology consists of the application of specific techniques coming from the HTA joined to the aid of the most typical models from reliability engineering such as FMEA/FMECA. The study has also included in-site data collection and interviews to medical personnel. The total number of robotic procedures included in the analysis was 44: 28 for urology and 16 for general surgery. The main outcomes refer to the comparative evaluation between robotic, laparoscopic and open surgery. Risk analysis and mitigation interventions come from FMECA application. The small sample size available for the study represents an important bias, especially for the clinical outcomes reliability. Despite this, the study seems to confirm the better trend for robotics' surgical times with comparison to the open technique as well as confirming the robotics' clinical benefits in urology. More complex situation is observed for general surgery, where robotics' clinical benefits directly measured are the lowest blood transfusion rate.

  5. METHODOLOGY OF ORGANIZATION OF INTEGRATED LESSONS OF NATURAL-SCIENCE CYCLE (ON THE EXAMPLE OF TEACHING SPE STUDENTS

    Directory of Open Access Journals (Sweden)

    Alsou Raufovna Kamaleeva

    2015-09-01

    Full Text Available In the process of transition of Russian organizations of secondary professional education to educational standards of the third generation educational process is reduced to formation of students’ competences. This article presents methodology of creating integrated lessons of natural-science cycle (for example, in physics and informatics. These lessons are constructed on the basis of interdisciplinary integration and focused on task solution. The main purpose is to teach students how to solve particular tasks in physics with the use of informatics, in particular on the basis of algorithmization and programming (Pascal language. Didactic conditions, which are the basis of the algorithm of designing corresponding tasks, are described in this article. Structural components of the integrated lessons created on the traditional principle are marked out. During the research we observed that realization of all stages of the corresponding lessons in practice allows the teacher to create educational process over the borders of disciplinary basis. This approach helps to form generalization of knowledge. Being one of the most optimal forms of education, an integrated lesson allows students to solve various educational and professional problems in non-standard situations and stimulates their cognitive activity and their involvement in the process of education and their responsibility for the result which promotes an intensification of educational process.

  6. A Alternative Analog Circuit Design Methodology Employing Integrated Artificial Intelligence Techniques

    Science.gov (United States)

    Tuttle, Jeffery L.

    In consideration of the computer processing power now available to the designer, an alternative analog circuit design methodology is proposed. Computer memory capacities no longer require the reduction of the transistor operational characteristics to an imprecise formulation. Therefore, it is proposed that transistor modelling be abandoned in favor of fully characterized transistor data libraries. Secondly, availability of the transistor libraries would facilitate an automated selection of the most appropriate device(s) for the circuit being designed. More specifically, a preprocessor computer program to a more sophisticated circuit simulator (e.g. SPICE) is developed to assist the designer in developing the basic circuit topology and the selection of the most appropriate transistor. Once this is achieved, the circuit topology and selected transistor data library would be downloaded to the simulator for full circuit operational characterization and subsequent design modifications. It is recognized that the design process is enhanced by the use of heuristics as applied to iterative design results. Accordingly, an artificial intelligence (AI) interface is developed to assist the designer in applying the preprocessor results. To demonstrate the retrofitability of the AI interface to established programs, the interface is specifically designed to be as non-intrusive to the host code as possible. Implementation of the proposed methodology offers the potential to speed the design process, since the preprocessor both minimizes the required number of simulator runs and provides a higher acceptance potential of the initial and subsequent simulator runs. Secondly, part count reductions may be realizable since the circuit topologies are not as strongly driven by transistor limitations. Thirdly, the predicted results should more closely match actual circuit operations since the inadequacies of the transistor models have been virtually eliminated. Finally, the AI interface

  7. Comparison of fungal spores concentrations measured with wideband integrated bioaerosol sensor and Hirst methodology

    Science.gov (United States)

    Fernández-Rodríguez, S.; Tormo-Molina, R.; Lemonis, N.; Clot, B.; O'Connor, D. J.; Sodeau, John R.

    2018-02-01

    The aim of this work was to provide both a comparison of traditional and novel methodologies for airborne spores detection (i.e. the Hirst Burkard trap and WIBS-4) and the first quantitative study of airborne fungal concentrations in Payerne (Western Switzerland) as well as their relation to meteorological parameters. From the traditional method -Hirst trap and microscope analysis-, sixty-three propagule types (spores, sporangia and hyphae) were identified and the average spore concentrations measured over the full period amounted to 4145 ± 263.0 spores/m3. Maximum values were reached on July 19th and on August 6th. Twenty-six spore types reached average levels above 10 spores/m3. Airborne fungal propagules in Payerne showed a clear seasonal pattern, increasing from low values in early spring to maxima in summer. Daily average concentrations above 5000 spores/m3 were almost constant in summer from mid-June onwards. Weather parameters showed a relevant role for determining the observed spore concentrations. Coniferous forest, dominant in the surroundings, may be a relevant source for airborne fungal propagules as their distribution and predominant wind directions are consistent with the origin. The comparison between the two methodologies used in this campaign showed remarkably consistent patterns throughout the campaign. A correlation coefficient of 0.9 (CI 0.76-0.96) was seen between the two over the time period for daily resolutions (Hirst trap and WIBS-4). This apparent co-linearity was seen to fall away once increased resolution was employed. However at higher resolutions upon removal of Cladosporium species from the total fungal concentrations (Hirst trap), an increased correlation coefficient was again noted between the two instruments (R = 0.81 with confidence intervals of 0.74 and 0.86).

  8. Methodological Approaches to Designing Integrated Systems of Management of Food Service Enterprises

    Directory of Open Access Journals (Sweden)

    Yatsun Leonid M.

    2016-02-01

    Full Text Available The article presents materials of studying the processes of designing functions and structures of management of food service enterprises by criteria of composition of the enterprise objectives, their participation in the integration process of production, sales and organization of consumption of food products and services. There have been defined a qualimetric estimation of parameters for enterprises of different size by types of tasks — manufacture of products, marketing activities, customer service, personnel management, etc. Balance schemes of the production and economic system of enterprises regarding cost components and output of food products and services have been developed. The integrated approaches to designing management systems of food service enterprises on the basis of coordination of parameters of the target, linear, functional and resource subsystems have been proposed.

  9. A Model-Based Methodology for Integrated Design and Operation of Reactive Distillation Processes

    DEFF Research Database (Denmark)

    Mansouri, Seyed Soheil; Sales-Cruz, Mauricio; Huusom, Jakob Kjøbsted

    2015-01-01

    and resolved. A new approach isto tackle process intensification and controllability issues in an integrated manner, in the early stages of process design. This integrated and simultaneous synthesis approach provides optimal operation and moreefficient control of complex intensified systems that suffice...... calculation of reactive bubble points. For an energy-efficient design, the driving-forc eapproach (to determine the optimal feed location) for a reactive system has been employed. For both thereactive McCabe-Thiele and driving force method, vapor-liquid equilibrium data are based on elements. Thereactive...... system of compounds (methanol, isobutene and MTBE) to a binary system ofelements (elements A and B). For a binary element system, a simple reactive McCabe-Thiele-type method (to determine the number of reactive stages) has been used. The reactive equilibrium curve is constructed through sequential...

  10. Development of probabilistic evaluation methodology for structural integrity of nuclear components

    International Nuclear Information System (INIS)

    Lee, Gang Yong; Yang, Jee Hyeok; Shin, Jeong Woo; Hong, Soon Won; Lee, Won Gyu; Kim, Goo Yeong

    1999-03-01

    Since integrity is very important in Nuclear Power Plants, there have been a lot of researches and several rules are provided. But these are mostly based on the concept of the deterministic fracture mechanics and in many cases, those rules are unrealistic or conservative. Therefore, the concept of the probabilistic fracture mechanics considering the realistic failure of the structure and the quantitative failure probability is introduced in many fields. There have been many researches on the probabilistic fracture mechanics in world, but a few in Korea. The final object of our research os to develop the code years. In the first year study, we obtained the concept of the probabilistic fracture mechanics by reviewing the papers about the integrity evaluation of the nuclear pressure vessel on the base of the probabilistic fracture mechanics and selected the important random variables by comparing the effects of random variables on the failure probability using the existing code

  11. A New Methodology for the Integration of Performance Materials into the Clothing Curriculum

    OpenAIRE

    Power, Jess

    2014-01-01

    This paper presents a model for integrating the study of performance materials into the clothing curriculum. In recent years there has been an increase in demand for stylish, functional and versatile sports apparel. Analysts predict this will reach US$126.30 billion by 2015. This growth is accredited to dramatic lifestyle changes and increasing participation in sports/leisurely pursuits particularly by women. The desire to own performance clothing for specific outdoor pursuits is increasing a...

  12. A Performance Measurement and Implementation Methodology in a Department of Defense CIM (Computer Integrated Manufacturing) Environment

    Science.gov (United States)

    1988-01-24

    vanes.-The new facility is currently being called the Engine Blade/ Vape Facility (EB/VF). There are three primary goals in automating this proc..e...earlier, the search led primarily into the areas of CIM Justification, Automation Strategies , Performance Measurement, and Integration issues. Of...of living, has been steadily eroding. One dangerous trend that has developed in keenly competitive world markets , says Rohan [33], has been for U.S

  13. Bidirectional Retroviral Integration Site PCR Methodology and Quantitative Data Analysis Workflow.

    Science.gov (United States)

    Suryawanshi, Gajendra W; Xu, Song; Xie, Yiming; Chou, Tom; Kim, Namshin; Chen, Irvin S Y; Kim, Sanggu

    2017-06-14

    Integration Site (IS) assays are a critical component of the study of retroviral integration sites and their biological significance. In recent retroviral gene therapy studies, IS assays, in combination with next-generation sequencing, have been used as a cell-tracking tool to characterize clonal stem cell populations sharing the same IS. For the accurate comparison of repopulating stem cell clones within and across different samples, the detection sensitivity, data reproducibility, and high-throughput capacity of the assay are among the most important assay qualities. This work provides a detailed protocol and data analysis workflow for bidirectional IS analysis. The bidirectional assay can simultaneously sequence both upstream and downstream vector-host junctions. Compared to conventional unidirectional IS sequencing approaches, the bidirectional approach significantly improves IS detection rates and the characterization of integration events at both ends of the target DNA. The data analysis pipeline described here accurately identifies and enumerates identical IS sequences through multiple steps of comparison that map IS sequences onto the reference genome and determine sequencing errors. Using an optimized assay procedure, we have recently published the detailed repopulation patterns of thousands of Hematopoietic Stem Cell (HSC) clones following transplant in rhesus macaques, demonstrating for the first time the precise time point of HSC repopulation and the functional heterogeneity of HSCs in the primate system. The following protocol describes the step-by-step experimental procedure and data analysis workflow that accurately identifies and quantifies identical IS sequences.

  14. A path integral methodology for obtaining thermodynamic properties of nonadiabatic systems using Gaussian mixture distributions

    Science.gov (United States)

    Raymond, Neil; Iouchtchenko, Dmitri; Roy, Pierre-Nicholas; Nooijen, Marcel

    2018-05-01

    We introduce a new path integral Monte Carlo method for investigating nonadiabatic systems in thermal equilibrium and demonstrate an approach to reducing stochastic error. We derive a general path integral expression for the partition function in a product basis of continuous nuclear and discrete electronic degrees of freedom without the use of any mapping schemes. We separate our Hamiltonian into a harmonic portion and a coupling portion; the partition function can then be calculated as the product of a Monte Carlo estimator (of the coupling contribution to the partition function) and a normalization factor (that is evaluated analytically). A Gaussian mixture model is used to evaluate the Monte Carlo estimator in a computationally efficient manner. Using two model systems, we demonstrate our approach to reduce the stochastic error associated with the Monte Carlo estimator. We show that the selection of the harmonic oscillators comprising the sampling distribution directly affects the efficiency of the method. Our results demonstrate that our path integral Monte Carlo method's deviation from exact Trotter calculations is dominated by the choice of the sampling distribution. By improving the sampling distribution, we can drastically reduce the stochastic error leading to lower computational cost.

  15. Fundamentals of equine podiatry: balanced trimming and physiological shoeing

    OpenAIRE

    Estrada, Manuel

    2014-01-01

    The concepts of balanced trimming and physiological shoeing of the equine hoof as a way to prevent asymmetrical weight bearing and related orthopedic problems are discussed in this paper. Suggestions are given for the technical training of the personnel involved.  Considering the quantity and quality of the existing equine herd in Costa Rica, it is recommended to create a Farrier School as well as to coordinate the necessary efforts with other educational institutions related to the animal in...

  16. TRIMS: Validating T2 Molecular Effects for Neutrino Mass Experiments

    Science.gov (United States)

    Lin, Ying-Ting; Trims Collaboration

    2017-09-01

    The Tritium Recoil-Ion Mass Spectrometer (TRIMS) experiment examines the branching ratio of the molecular tritium (T2) beta decay to the bound state (3HeT+). Measuring this branching ratio helps to validate the current molecular final-state theory applied in neutrino mass experiments such as KATRIN and Project 8. TRIMS consists of a magnet-guided time-of-flight mass spectrometer with a detector located on each end. By measuring the kinetic energy and time-of-flight difference of the ions and beta particles reaching the detectors, we will be able to distinguish molecular ions from atomic ones and hence derive the ratio in question. We will give an update on the apparatus, simulation software, and analysis tools, including efforts to improve the resolution of our detectors and to characterize the stability and uniformity of our field sources. We will also share our commissioning results and prospects for physics data. The TRIMS experiment is supported by U.S. Department of Energy Office of Science, Office of Nuclear Physics, Award Number DE-FG02-97ER41020.

  17. Integration of a solar thermal system in a medium-sized brewery using pinch analysis: Methodology and case study

    International Nuclear Information System (INIS)

    Eiholzer, Tobias; Olsen, Donald; Hoffmann, Sebastian; Sturm, Barbara; Wellig, Beat

    2017-01-01

    Highlights: • Methodologies to reduce energy consumption in batch processes are presented. • Pinch analysis is used to improve energy efficiency. • Integration potential for solar heat is presented on a Scottish brewery case study. • Governmental support is important in a company’s investment in renewables. - Abstract: In the food industry a major portion of thermal energy is required for low temperature applications (below 100 °C). As a consequence, there is a significant potential to substitute fossil fuels by the use of solar heat. This paper presents a methodology that first uses pinch analysis to optimize a medium-sized Scottish brewery from a direct heat recovery perspective followed by the integration of a solar thermal system. Both the time average model and time slice model were used to determine direct and indirect heat recovery potentials. In a second stage, an optimization of a chosen integration point was conducted to assess the viability of the resulting design concept. The economic analysis includes an assessment of the impact of restrictions in the UK government’s Renewable Heat Incentive program. It was determined that since solar thermal systems are financially supported up to an installed capacity of 200 kW, solar heat can only account for a maximum of 7.7% of the heat demand based on the investigated brewery. However, if there was no limitation in capacity, from an economic point of view, the solar fraction could almost be doubled drawing into question the need for the restriction. Nevertheless, a CO_2 saving potential of approximately 38 tons per year in conjunction with a payback period of 6.4 years was determined.

  18. Digital System Categorization Methodology to Support Integration of Digital Instrumentation and Control Models into PRAs

    International Nuclear Information System (INIS)

    Arndt, Steven A.

    2011-01-01

    It has been suggested that by categorizing the various digital systems used in safety critical applications in nuclear power plants, it would be possible to determine which systems should be modeled in the analysis of the larger plant wide PRA, at what level of detail the digital system should be modeled and using which methods. The research reported in this paper develops a categorization method using system attributes to permit a modeler to more effectively model the systems that will likely have the most critical contributions to the overall plant safety and to more effectively model system interactions for those digital systems where the interactions are most important to the overall accuracy and completeness of the plant PRA. The proposed methodology will categorize digital systems based on certain attributes of the systems themselves and how they will be used in the specific application. This will help determine what digital systems need to be modeled and at what level of detail, and can be used to guide PRA analysis and regulatory reviews. The three-attribute categorization strategy that was proposed by Arndt is used as the basis for the categorization methodology developed here. The first attribute, digital system complexity, is based on Type Il interactions defined by Aldemir and an overall digital system size and complexity index. The size and complexity index used are previously defined software complexity metrics. Potential sub-attributes of digital system complexity include, design complexity, software complexity, hardware complexity, system function complexity and testability. The second attribute, digital system interactions/inter-conductivity, is a combination of Rushby's coupling and Ademir's Type I interactions. Digital systems that are loosely coupled and/or have very few Type I interaction would not interact dynamically with the overall system and would have a low interactions/inter-conductivity score. Potential sub-attributes of digital system

  19. Digital System Categorization Methodology to Support Integration of Digital Instrumentation and Control Models into PRAs

    Energy Technology Data Exchange (ETDEWEB)

    Arndt, Steven A. [U.S. Nuclear Regulatory Commission, Washington D.C. (United States)

    2011-08-15

    It has been suggested that by categorizing the various digital systems used in safety critical applications in nuclear power plants, it would be possible to determine which systems should be modeled in the analysis of the larger plant wide PRA, at what level of detail the digital system should be modeled and using which methods. The research reported in this paper develops a categorization method using system attributes to permit a modeler to more effectively model the systems that will likely have the most critical contributions to the overall plant safety and to more effectively model system interactions for those digital systems where the interactions are most important to the overall accuracy and completeness of the plant PRA. The proposed methodology will categorize digital systems based on certain attributes of the systems themselves and how they will be used in the specific application. This will help determine what digital systems need to be modeled and at what level of detail, and can be used to guide PRA analysis and regulatory reviews. The three-attribute categorization strategy that was proposed by Arndt is used as the basis for the categorization methodology developed here. The first attribute, digital system complexity, is based on Type Il interactions defined by Aldemir and an overall digital system size and complexity index. The size and complexity index used are previously defined software complexity metrics. Potential sub-attributes of digital system complexity include, design complexity, software complexity, hardware complexity, system function complexity and testability. The second attribute, digital system interactions/inter-conductivity, is a combination of Rushby's coupling and Ademir's Type I interactions. Digital systems that are loosely coupled and/or have very few Type I interaction would not interact dynamically with the overall system and would have a low interactions/inter-conductivity score. Potential sub-attributes of

  20. THE METHODOLOGY OF DEVELOPING VALUE INDICATORS TO INTEGRALLY ASSESS RESOURCE POTENTIAL IN AGRICULTURAL UNITS

    Directory of Open Access Journals (Sweden)

    Elena TIMOFTI

    2014-06-01

    Full Text Available The problem of increasing the economic efficiency of resource use in agricultural production is very important. Its solution directly depends on the economic security of the country and its constant supply with agricultural products.There are three basic factors in agricultural production: nature (land, labour and capital, which have differentmeasure units. Comparability is necessary to express the value of the integral potential that gives the possibility totake into account the main resources involved in producing and obtaining results from the agricultural sector.

  1. A Methodology to Integrate Magnetic Resonance and Acoustic Measurements for Reservoir Characterization

    Energy Technology Data Exchange (ETDEWEB)

    Parra, Jorge O.; Hackert, Chris L.; Collier, Hughbert A.; Bennett, Michael

    2002-01-29

    The objective of this project was to develop an advanced imaging method, including pore scale imaging, to integrate NMR techniques and acoustic measurements to improve predictability of the pay zone in hydrocarbon reservoirs. This is accomplished by extracting the fluid property parameters using NMR laboratory measurements and the elastic parameters of the rock matrix from acoustic measurements to create poroelastic models of different parts of the reservoir. Laboratory measurement techniques and core imaging are being linked with a balanced petrographical analysis of the core and theoretical model.

  2. Development of a practical methodology for integrating shoreline oil-holding capacity into modeling

    International Nuclear Information System (INIS)

    Schmidt Etkin, D.; French-McCay, D.; Rowe, J.; Michel, J.; Boufadel, M.; Li, H.

    2008-01-01

    The factors that influence the behaviour of oil in the aftermath of an oil spill on water include oil type and characteristics; oil thickness on the shoreline; time until shoreline impact; timing with regards to tides; weathering during and after the spill; and nearshore wave energy. The oil behaviour also depends on the shoreline characteristics, particularly porosity and permeability. The interactions of spilled oil with sediments on beaches must be well understood in order to model the oil spill trajectory, fate and risk. The movement of oil can be most accurately simulated if the algorithm incorporates an estimate of shoreline oil retention. This paper presented a literature review of relevant shoreline oiling studies and considered the relevance of study findings for inclusion in modelling. Survey data from a detailed shoreline cleanup assessment team (SCAT) were analyzed for patterns in oil penetration and oil-holding capacity by shoreline sediment type and oil type for potential use in modelling algorithms. A theoretical beach hydraulics model was then developed for use in a stochastic spill model. Gaps in information were identified, including the manner in which wave action and other environmental variables have an impact on the dynamic processes involved in shoreline oiling. The methodology presented in this paper can be used to estimate the amount of oil held by a shoreline upon impact to allow a trajectory model to more accurately project the total spread of oil. 27 refs., 13 tabs., 3 figs

  3. State-of-The-Art of Modeling Methodologies and Optimization Operations in Integrated Energy System

    Science.gov (United States)

    Zheng, Zhan; Zhang, Yongjun

    2017-08-01

    Rapid advances in low carbon technologies and smart energy communities are reshaping future patterns. Uncertainty in energy productions and demand sides are paving the way towards decentralization management. Current energy infrastructures could not meet with supply and consumption challenges, along with emerging environment and economic requirements. Integrated Energy System(IES) whereby electric power, natural gas, heating couples with each other demonstrates that such a significant technique would gradually become one of main comprehensive and optimal energy solutions with high flexibility, friendly renewables absorption and improving efficiency. In these global energy trends, we summarize this literature review. Firstly the accurate definition and characteristics of IES have been presented. Energy subsystem and coupling elements modeling issues are analyzed. It is pointed out that decomposed and integrated analysis methods are the key algorithms for IES optimization operations problems, followed by exploring the IES market mechanisms. Finally several future research tendencies of IES, such as dynamic modeling, peer-to-peer trading, couple market design, sare under discussion.

  4. INTEGRATED SURVEY FOR ARCHITECTURAL RESTORATION: A METHODOLOGICAL COMPARISON OF TWO CASE STUDIES

    Directory of Open Access Journals (Sweden)

    G. Bianchi

    2016-06-01

    Full Text Available A preliminary survey campaign is essential in projects of restoration, urban renewal, rebuilding or promotion of architectural heritage. Today several survey techniques allow full 3D object restitution and modelling that provides a richer description than simple 2D representations. However, the amount of data to collect increases dramatically and a trade-off between efficiency and productivity from one side and assuring accuracy and completeness of the results on the other must be found. Depending on the extent and the complexity of the task, a single technique or a combination of several ones might be employed. Especially when documentation at different scales and with different levels of detail are foreseen, the latter will likely be necessary. The paper describes two architectural surveys in Italy: the old village of Navelli (AQ, affected by the earthquake in 2009, and the two most relevant remains in Codiponte (MS, damaged by the earthquake in 2013, both in the context of a project of restoration and conservation. In both sites, a 3D survey was necessary to represent effectively the objects. An integrated survey campaign was performed in both cases, which consists of a GPS network as support for georeferencing, an aerial survey and a field survey made by laser scanner and close range photogrammetry. The two case studies, thanks to their peculiarities, can be taken as exemplar to wonder if the integration of different surveying techniques is today still mandatory or, considering the technical advances of each technology, it is in fact just optional.

  5. Integrating 3D seismic curvature and curvature gradient attributes for fracture characterization: Methodologies and interpretational implications

    Energy Technology Data Exchange (ETDEWEB)

    Gao, Dengliang

    2013-03-01

    In 3D seismic interpretation, curvature is a popular attribute that depicts the geometry of seismic reflectors and has been widely used to detect faults in the subsurface; however, it provides only part of the solutions to subsurface structure analysis. This study extends the curvature algorithm to a new curvature gradient algorithm, and integrates both algorithms for fracture detection using a 3D seismic test data set over Teapot Dome (Wyoming). In fractured reservoirs at Teapot Dome known to be formed by tectonic folding and faulting, curvature helps define the crestal portion of the reservoirs that is associated with strong seismic amplitude and high oil productivity. In contrast, curvature gradient helps better define the regional northwest-trending and the cross-regional northeast-trending lineaments that are associated with weak seismic amplitude and low oil productivity. In concert with previous reports from image logs, cores, and outcrops, the current study based on an integrated seismic curvature and curvature gradient analysis suggests that curvature might help define areas of enhanced potential to form tensile fractures, whereas curvature gradient might help define zones of enhanced potential to develop shear fractures. In certain fractured reservoirs such as at Teapot Dome where faulting and fault-related folding contribute dominantly to the formation and evolution of fractures, curvature and curvature gradient attributes can be potentially applied to differentiate fracture mode, to predict fracture intensity and orientation, to detect fracture volume and connectivity, and to model fracture networks.

  6. Protocol: An updated integrated methodology for analysis of metabolites and enzyme activities of ethylene biosynthesis

    Directory of Open Access Journals (Sweden)

    Geeraerd Annemie H

    2011-06-01

    Full Text Available Abstract Background The foundations for ethylene research were laid many years ago by researchers such as Lizada, Yang and Hoffman. Nowadays, most of the methods developed by them are still being used. Technological developments since then have led to small but significant improvements, contributing to a more efficient workflow. Despite this, many of these improvements have never been properly documented. Results This article provides an updated, integrated set of protocols suitable for the assembly of a complete picture of ethylene biosynthesis, including the measurement of ethylene itself. The original protocols for the metabolites 1-aminocyclopropane-1-carboxylic acid and 1-(malonylaminocyclopropane-1-carboxylic acid have been updated and downscaled, while protocols to determine in vitro activities of the key enzymes 1-aminocyclopropane-1-carboxylate synthase and 1-aminocyclopropane-1-carboxylate oxidase have been optimised for efficiency, repeatability and accuracy. All the protocols described were optimised for apple fruit, but have been proven to be suitable for the analysis of tomato fruit as well. Conclusions This work collates an integrated set of detailed protocols for the measurement of components of the ethylene biosynthetic pathway, starting from well-established methods. These protocols have been optimised for smaller sample volumes, increased efficiency, repeatability and accuracy. The detailed protocol allows other scientists to rapidly implement these methods in their own laboratories in a consistent and efficient way.

  7. TRIM37 defective in mulibrey nanism is a novel RING finger ubiquitin E3 ligase

    International Nuclear Information System (INIS)

    Kallijaervi, Jukka; Lahtinen, Ulla; Haemaelaeinen, Riikka; Lipsanen-Nyman, Marita; Palvimo, Jorma J.; Lehesjoki, Anna-Elina

    2005-01-01

    Mulibrey nanism is an autosomal recessive prenatal-onset growth disorder characterized by dysmorphic features, cardiomyopathy, and hepatomegaly. Mutations in TRIM37 encoding a tripartite motif (TRIM, RING-B-box-coiled-coil)-family protein underlie mulibrey nanism. We investigated the ubiquitin ligase activity predicted for the RING domain of TRIM37 by analyzing its autoubiquitination. Full-length TRIM37 and its TRIM domain were highly polyubiquitinated when co-expressed with ubiquitin. Polyubiquitination was decreased in a mutant protein with disrupted RING domain (Cys35Ser;Cys36Ser) and in the Leu76Pro mutant protein, a disease-associated missense mutation affecting the TRIM domain of TRIM37. Bacterially produced GST-TRIM domain fusion protein, but not its Cys35Ser;Cys36Ser or Leu76Pro mutants, were polyubiquitinated in cell-free conditions, implying RING-dependent modification. Ubiquitin was also identified as an interaction partner for TRIM37 in a yeast two-hybrid screen. Ectopically expressed TRIM37 rapidly formed aggregates that were ubiquitin-, proteasome subunit-, and chaperone-positive in immunofluorescence analysis, defining them as aggresomes. The Cys35Ser;Cys36Ser mutant and the Leu76Pro and Gly322Val patient mutant proteins were markedly less prone to aggregation, implying that aggresomal targeting reflects a physiological function of TRIM37. These findings suggest that TRIM37 acts as a TRIM domain-dependent E3 ubiquitin ligase and imply defective ubiquitin-dependent degradation of an as-yet-unidentified target protein in the pathogenesis of mulibrey nanism

  8. The Potential Role of Mental Model Methodologies in Multistakeholder Negotiations: Integrated Water Resources Management in South Africa

    Directory of Open Access Journals (Sweden)

    Derick R. Du Toit

    2011-09-01

    Full Text Available Equitable redistribution of resources is an emergent phenomenon in democratizing countries, and attempts are often characterized by decentralized decision making within a framework of multistakeholder negotiations. South Africa offers a unique opportunity to explore the manifestations of these relationships, particularly through Integrated Water Resources Management and its National Water Act of 1998. The Integrated Water Resources Management framework provides for collaborative strategic planning, shared visioning, consideration to water resource protection, attention to the regulation of use, operational planning, and implementation of management plans. Water users, with different stakes and views of how the resource should be managed, are expected to arrive at a single strategic plan for a specific hydrological region. Clearly this complex planning situation creates a need for tools that assist in producing a measure of convergence in thinking and enough of a shared rationale to allow stakeholder participation to produce an integrated management outcome. Several such tools are available in the overall catchment management strategy, but these would benefit from clearer understanding of the positions from which different stakeholders are operating and a way of knowing whether these positions are aligning. In this paper challenges posed by differences in meaning and understanding amongst stakeholders are examined against the need to engage stakeholders in water resources management. We deliberate on the prospects of employing mental model methodologies within the context of the strategic management framework for water management described.

  9. Using integrated control methodology to optimize energy performance for the guest rooms in UAE hospitality sector

    International Nuclear Information System (INIS)

    AlFaris, Fadi; Abu-Hijleh, Bassam; Abdul-Ameer, Alaa

    2016-01-01

    Highlights: • Energy efficiency in 4 and 5 star luxury hotels in the United Arab Emirates. • The normalized energy use index (EUI) ranges between 241.5 and 348.4 kWh/m"2/year for post 2003 hotels. • The normalized energy use index (EUI) ranges between 348.4 and 511.1 kWh/m"2/year for pre 2003 hotels. • Integrated HVAC and lighting control strategies can reduce total energy consumption by up to 31.5%. - Abstract: The hospitality sector is growing rapidly in the UAE and especially in Dubai. As a result, it contributes substantially in the UAE's carbon footprint. This research was conducted to measure, evaluate and increase the energy efficiency in 4 and 5 star luxury hotels in UAE. Energy benchmarking analysis was used to analyze the energy data of 19 hotel buildings to differentiate between usual and best practice of energy performance. Moreover, the normalized energy use index (EUI) kWh/m"2/year has been identified for the best, usual and poor practice hotels. It was found that the normalized EUI ranges between 241.5 kWh/m"2/year or less as a best practice to more than 361.3 kWh/m"2/year of the poor energy practice for the hotels constructed after the year of 2003. Whereas the hotels' energy data showed higher values for those constructed before 2003, as the normalized EUI varies between 348.4 kWh/m"2/year as best practice to more than 511.1 kWh/m"2/year. An integrated control strategy has been employed to improve the energy performance and assess the energy saving for the guestroom. This technique showed that the overall energy performance improvement reached to 31.5% out of entire energy consumption of the hotel including electricity and gas. This reduction resulted in 43.2% savings from the cooling system and 13.2% from the lighting system due to the installing of the integrated control system in the guestrooms.

  10. The Effect of Various Parameters of Solution Methodology on a Flexible Integrated Supply Chain Model

    Directory of Open Access Journals (Sweden)

    Elham Behmanesh

    2018-01-01

    Full Text Available A successful supply chain must be able to operate at the lowest cost while providing the best customer service as well as environmental protection. As industrial players are under pressure but mostly unprepared to take back products after their usage, logistics network design becomes an even more important issue. To allow for a maximum of flexibility and efficiency, we consider an integrated design of the forward/reverse logistics network using full delivery graph. We apply a Memetic Algorithm with a novel population generation to find a near optimal solution for large size problems. The effect of different parameters on the behavior of the proposed Metaheuristic Algorithm is investigated. Using the experimental work to find the best parameters for this problem is the outlook of these researches.

  11. An integrated multi-criteria decision-making methodology for conveyor system selection

    Directory of Open Access Journals (Sweden)

    Pairat Jiamruangjarus

    2016-12-01

    Full Text Available Material handling equipment (MHE is important for every industry because it has an effect on the productivity of manufacturing. Conveyor systems are presently one popular type of MHE. This paper presents an integration of the analytic network process (ANP with the benefits, opportunities, costs and risk (BOCR model in order to select the best conveyor system. The proposed model established a network with four merits, six strategies criteria, and twenty six sub-criteria with four alternatives (present, roller conveyor, chain conveyor, and monorail. The ANP is to determine the relative weights of an evaluative criteria and decision alternatives. Therefore, the final ranking of the alternatives are calculated by synthesizing the score of each alternative under BOCR. The results showed that the best alternative under all five methods is the chain conveyor. These research results can be easily applied, adapted and used to improve performance of selecting the conveyer system in small and medium enterprises through large industries.

  12. Integrated Data Processing Methodology for Airborne Repeat-pass Differential SAR Interferometry

    Science.gov (United States)

    Dou, C.; Guo, H.; Han, C.; Yue, X.; Zhao, Y.

    2014-11-01

    Short temporal baseline and multiple ground deformation information can be derived from the airborne differential synthetic aperture radar Interforemetry (D-InSAR). However, affected by the turbulence of the air, the aircraft would deviate from the designed flight path with high frequent vibrations and changes both in the flight trajectory and attitude. Restricted by the accuracy of the position and orientation system (POS), these high frequent deviations can not be accurately reported, which would pose great challenges in motion compensation and interferometric process. Thus, these challenges constrain its wider applications. The objective of this paper is to investigate the accurate estimation and compensation of the residual motion errors in the airborne SAR imagery and time-varying baseline errors between the diffirent data acquirations, furthermore, to explore the integration data processing theory for the airborne D-InSAR system, and thus help to accomplish the correct derivation of the ground deformation by using the airborne D-InSAR measurements.

  13. Continental mapping of groundwater dependent ecosystems: A methodological framework to integrate diverse data and expert opinion

    Directory of Open Access Journals (Sweden)

    Tanya M. Doody

    2017-04-01

    New hydrological insights: It was identified that 34% of Australia’s landscape potentially contains GDEs of which 5% are classified with a high GDE potential. In addition, new continental scale insights into landscape processes where provided by the derivation and integration of remote sensing products using MODIS and Landsat. These products identify landscapes which are ‘wetter’ or ‘greener’ than surrounding areas, indicating these landscapes are accessing additional water, such as groundwater, supplementary to rainfall. The method reported also demonstrates the importance of expert knowledge, obtained through literature and expert elicitation, in order to provide a conceptual understanding of regional ecohydrological processes to develop rules of GDE dependency that would guide the extrapolation of known GDEs.

  14. WOMEN, FOOTBALL AND EUROPEAN INTEGRATION. AIMS AND QUESTIONS, METHODOLOGICAL AND THEORETICAL APPROACHES

    Directory of Open Access Journals (Sweden)

    Gertrud Pfister

    2013-12-01

    Full Text Available The aim of this article is to introduce a new research topic and provide information about a European research project focusing on football as a means of European integration. Using the results of available studies of the author and other scholars, it is to be discussed whether and how women can participate in football cultures and contribute to a European identity. Based on theoretical approaches to national identity, gender and socialization, as well as and on the analysis of various intersections between gender, football and fandom, it can be concluded that women are still outsiders in the world of football and that it is doubtful whether female players and fans will contribute decisively to Europeanization processes.

  15. Development of an integrated methodology for the sustainable environmental and socio-economic management of river ecosystems.

    Science.gov (United States)

    Koundouri, P; Ker Rault, P; Pergamalis, V; Skianis, V; Souliotis, I

    2016-01-01

    The development of the Water Framework Directive aimed to establish an integrated framework of water management at European level. This framework revolves around inland surface waters, transitional waters, coastal waters and ground waters. In the process of achieving the environment and ecological objectives set from the Directive, the role of economics is put in the core of the water management. An important feature of the Directive is the recovery of total economic cost of water services by all users. The total cost of water services can be disaggregated into environmental, financial and resource costs. Another important aspect of the directive is the identification of major drivers and pressures in each River Basin District. We describe a methodology that is aiming to achieve sustainable and environmental and socioeconomic management of freshwater ecosystem services. The Ecosystem Services Approach is in the core of the suggested methodology for the implementation of a more sustainable and efficient water management. This approach consists of the following three steps: (i) socio-economic characterization of the River Basin area, (ii) assessment of the current recovery of water use cost, and (iii) identification and suggestion of appropriate programs of measures for sustainable water management over space and time. This methodology is consistent with a) the economic principles adopted explicitly by the Water Framework Directive (WFD), b) the three-step WFD implementation approach adopted in the WATECO document, c) the Ecosystem Services Approach to valuing freshwater goods and services to humans. Furthermore, we analyze how the effects of multiple stressors and socio-economic development can be quantified in the context of freshwater resources management. We also attempt to estimate the value of four ecosystem services using the benefit transfer approach for the Anglian River Basin, which showed the significance of such services. Copyright © 2015. Published by

  16. Methodological study of the adjustment of multigroup cross sections for fast reactors, by means of integral data

    International Nuclear Information System (INIS)

    Bastos, H.F.B.N.

    1979-01-01

    In this work a study of the methodology of the adjustment of multigroup cross sections by means of integral data is presented. A synthesis of the principal methods existent and the mathematical development of the adaptation of one of them are made. A calculational system is built from this reference method, with the basic conditions for the operation of the process of adjustment. In order to test the system developed and analyze several problems related to the adjustment, a series of trial adjustments was made with the value of the U 235 fission cross section from the infinite dilution library used in the calculational system for fast reactors of the Instituto de Engenharia Nuclear. (author)

  17. Integrated methodology for standard-setting norms of innovative product in the new competitive environment

    Science.gov (United States)

    Polyakova, Marina; Rubin, Gennadiy

    2017-07-01

    Modern theory of technological and economical development is based on long-term cycles. So far it has been proved that the technological structure of the economy can be subdivided into groups of technological complexes, which are inter-related with each other by similar technological links, so called technological modes. Technological mode is defined as a complex of interrelated production units of similar technological level, which develop simultaneously. In order to provide competitiveness of products in the new changing conditions, it is necessary to make sure that they meet all the regulatory requirements specified in standards. But the existing and the fast changing situation on the merchandise markets causes disbalance between the growing customer requirements and the technological capabilities of the manufacturer. This makes the issue of standardization development even more urgent both from the point of view of establishing the current positions and from the point of view of possible promising development trends in technology. In the paper scientific and engineering principles of developing standardization as a science are described. It is shown that further development of standardization is based on the principles of advanced standardization the main idea of which is to set up the prospective requirements to the innovative product. Modern approaches of advanced standardization are shown in this paper. The complexity of the negotiation procedure between customer and manufacturer as a whole and achieving of consensus, in particular, make it necessary to find conceptually new approaches to developing mathematical models. The developed methodology picture the process of achieving the consensus between customer and manufacturer while developing the standard norms in the form of decreasing S-curve diagram. It means that in the end of the negotiation process, there is no difference between customer and manufacturer positions. It makes it possible to provide the

  18. CI-Miner: A Semantic Methodology to Integrate Scientists, Data and Documents through the Use of Cyber-Infrastructure

    Science.gov (United States)

    Pinheiro da Silva, P.; CyberShARE Center of Excellence

    2011-12-01

    Scientists today face the challenge of rethinking the manner in which they document and make available their processes and data in an international cyber-infrastructure of shared resources. Some relevant examples of new scientific practices in the realm of computational and data extraction sciences include: large scale data discovery; data integration; data sharing across distinct scientific domains, systematic management of trust and uncertainty; and comprehensive support for explaining processes and results. This talk introduces CI-Miner - an innovative hands-on, open-source, community-driven methodology to integrate these new scientific practices. It has been developed in collaboration with scientists, with the purpose of capturing, storing and retrieving knowledge about scientific processes and their products, thereby further supporting a new generation of science techniques based on data exploration. CI-Miner uses semantic annotations in the form of W3C Ontology Web Language-based ontologies and Proof Markup Language (PML)-based provenance to represent knowledge. This methodology specializes in general-purpose ontologies, projected into workflow-driven ontologies(WDOs) and into semantic abstract workflows (SAWs). Provenance in PML is CI-Miner's integrative component, which allows scientists to retrieve and reason with the knowledge represented in these new semantic documents. It serves additionally as a platform to share such collected knowledge with the scientific community participating in the international cyber-infrastructure. The integrated semantic documents that are tailored for the use of human epistemic agents may also be utilized by machine epistemic agents, since the documents are based on W3C Resource Description Framework (RDF) notation. This talk is grounded upon interdisciplinary lessons learned through the use of CI-Miner in support of government-funded national and international cyber-infrastructure initiatives in the areas of geo

  19. Optimization of integrated chemical-biological degradation of a reactive azo dye using response surface methodology

    Energy Technology Data Exchange (ETDEWEB)

    Sudarjanto, Gatut [Advanced Wastewater Management Centre, The University of Queensland, Qld 4072 (Australia); Keller-Lehmann, Beatrice [Advanced Wastewater Management Centre, The University of Queensland, Qld 4072 (Australia); Keller, Jurg [Advanced Wastewater Management Centre, The University of Queensland, Qld 4072 (Australia)]. E-mail: j.keller@awmc.uq.edu.au

    2006-11-02

    The integrated chemical-biological degradation combining advanced oxidation by UV/H{sub 2}O{sub 2} followed by aerobic biodegradation was used to degrade C.I. Reactive Azo Red 195A, commonly used in the textile industry in Australia. An experimental design based on the response surface method was applied to evaluate the interactive effects of influencing factors (UV irradiation time, initial hydrogen peroxide dosage and recirculation ratio of the system) on decolourisation efficiency and optimizing the operating conditions of the treatment process. The effects were determined by the measurement of dye concentration and soluble chemical oxygen demand (S-COD). The results showed that the dye and S-COD removal were affected by all factors individually and interactively. Maximal colour degradation performance was predicted, and experimentally validated, with no recirculation, 30 min UV irradiation and 500 mg H{sub 2}O{sub 2}/L. The model predictions for colour removal, based on a three-factor/five-level Box-Wilson central composite design and the response surface method analysis, were found to be very close to additional experimental results obtained under near optimal conditions. This demonstrates the benefits of this approach in achieving good predictions while minimising the number of experiments required.

  20. Optimization of integrated chemical-biological degradation of a reactive azo dye using response surface methodology

    International Nuclear Information System (INIS)

    Sudarjanto, Gatut; Keller-Lehmann, Beatrice; Keller, Jurg

    2006-01-01

    The integrated chemical-biological degradation combining advanced oxidation by UV/H 2 O 2 followed by aerobic biodegradation was used to degrade C.I. Reactive Azo Red 195A, commonly used in the textile industry in Australia. An experimental design based on the response surface method was applied to evaluate the interactive effects of influencing factors (UV irradiation time, initial hydrogen peroxide dosage and recirculation ratio of the system) on decolourisation efficiency and optimizing the operating conditions of the treatment process. The effects were determined by the measurement of dye concentration and soluble chemical oxygen demand (S-COD). The results showed that the dye and S-COD removal were affected by all factors individually and interactively. Maximal colour degradation performance was predicted, and experimentally validated, with no recirculation, 30 min UV irradiation and 500 mg H 2 O 2 /L. The model predictions for colour removal, based on a three-factor/five-level Box-Wilson central composite design and the response surface method analysis, were found to be very close to additional experimental results obtained under near optimal conditions. This demonstrates the benefits of this approach in achieving good predictions while minimising the number of experiments required

  1. ANN-PSO Integrated Optimization Methodology for Intelligent Control of MMC Machining

    Science.gov (United States)

    Chandrasekaran, Muthumari; Tamang, Santosh

    2017-08-01

    Metal Matrix Composites (MMC) show improved properties in comparison with non-reinforced alloys and have found increased application in automotive and aerospace industries. The selection of optimum machining parameters to produce components of desired surface roughness is of great concern considering the quality and economy of manufacturing process. In this study, a surface roughness prediction model for turning Al-SiCp MMC is developed using Artificial Neural Network (ANN). Three turning parameters viz., spindle speed ( N), feed rate ( f) and depth of cut ( d) were considered as input neurons and surface roughness was an output neuron. ANN architecture having 3 -5 -1 is found to be optimum and the model predicts with an average percentage error of 7.72 %. Particle Swarm Optimization (PSO) technique is used for optimizing parameters to minimize machining time. The innovative aspect of this work is the development of an integrated ANN-PSO optimization method for intelligent control of MMC machining process applicable to manufacturing industries. The robustness of the method shows its superiority for obtaining optimum cutting parameters satisfying desired surface roughness. The method has better convergent capability with minimum number of iterations.

  2. A singular methodology to design cement sheath integrity exposed to steam stimulation

    Energy Technology Data Exchange (ETDEWEB)

    Garnier, A.; Saint-Marc, J. [Total SA, Paris (France); Bois, A.P. [CurisTec (France); Kermanac' h, Y. [Total E and P Canada Ltd., Calgary, AB (Canada)

    2008-10-15

    Oil well cements must be capable of providing zonal isolation as well as casing support and casing protection. However, steam assisted gravity drainage (SAGD) processes often place significant stresses on well casings and cement sheath boundaries. This paper presented a barrier design developed to ensure long-term cement sheath integrity in shallow reservoir conditions. Rock mechanics simulations were conducted in order to evaluate stresses in the field. The thermal gradient in well components was simulated. Thermo-hydraulic simulations of SAGD processes were conducted in order to evaluate thermal loadings and develop a series of temperature grids. Well trajectory, architecture and geology were considered, as well as formation properties, pore pressures, in situ stress states, and applied loadings. The results of both studies were then analyzed in order to determine the mechanical properties required by the cement in order to withstand thermal stresses. Various cement systems were then triaxial tested in order to validate simulation results. The method was used to design a cement system with low Young's modulus and high tensile strength at a well in the Joslyn field in Canada. The method is now being used by Total in fields throughout the world. 19 refs., 5 tabs., 16 figs.

  3. Structure and catalytic activation of the TRIM23 RING E3 ubiquitin ligase: DAWIDZIAK et al.

    Energy Technology Data Exchange (ETDEWEB)

    Dawidziak, Daria M. [Department of Molecular Physiology and Biological Physics, University of Virginia, Charlottesville Virginia; Sanchez, Jacint G. [Department of Molecular Physiology and Biological Physics, University of Virginia, Charlottesville Virginia; Wagner, Jonathan M. [Department of Molecular Physiology and Biological Physics, University of Virginia, Charlottesville Virginia; Ganser-Pornillos, Barbie K. [Department of Molecular Physiology and Biological Physics, University of Virginia, Charlottesville Virginia; Pornillos, Owen [Department of Molecular Physiology and Biological Physics, University of Virginia, Charlottesville Virginia

    2017-07-24

    Tripartite motif (TRIM) proteins comprise a large family of RING-type ubiquitin E3 ligases that regulate important biological processes. An emerging general model is that TRIMs form elongated antiparallel coiled-coil dimers that prevent interaction of the two attendant RING domains. The RING domains themselves bind E2 conjugating enzymes as dimers, implying that an active TRIM ligase requires higher-order oligomerization of the basal coiled-coil dimers. Here, we report crystal structures of the TRIM23 RING domain in isolation and in complex with an E2–ubiquitin conjugate. Our results indicate that TRIM23 enzymatic activity requires RING dimerization, consistent with the general model of TRIM activation.

  4. Helicopter Non-Unique Trim Strategies for Blade-Vortex Interaction (BVI) Noise Reduction

    Science.gov (United States)

    Malpica, Carlos; Greenwood, Eric; Sim, Ben W.

    2016-01-01

    An acoustics parametric analysis of the effect of fuselage drag and pitching moment on the Blade-Vortex Interaction (BVI) noise radiated by a medium lift helicopter (S-70UH-60) in a descending flight condition was conducted. The comprehensive analysis CAMRAD II was used for the calculation of vehicle trim, wake geometry and integrated air loads on the blade. The acoustics prediction code PSU-WOPWOP was used for calculating acoustic pressure signatures for a hemispherical grid centered at the hub. This paper revisits the concept of the X-force controller for BVI noise reduction, and investigates its effectiveness on an S-70 helicopter. The analysis showed that further BVI noise reductions were achievable by controlling the fuselage pitching moment. Reductions in excess of 6 dB of the peak BVI noise radiated towards the ground were demonstrated by compounding the effect of airframe drag and pitching moment simultaneously.

  5. The TE coupled RELAP5/PANTHER/COBRA code package and methodology for integrated PWR accident analysis

    International Nuclear Information System (INIS)

    Schneidesch, Christophe R.; Zhang, Jinzhao; Ammirabile, Luca; Dalleur, Jean-Paul

    2006-01-01

    coupled thermal hydraulic-neutronic transient calculations allow realistic simulations and hence better understanding the key physical phenomena. The TE coupled code package will be applied to develop coupled analysis methodologies for integrated safety analysis of other PWR accidents. (authors)

  6. The TE coupled RELAP5/PANTHER/COBRA code package and methodology for integrated PWR accident analysis

    Energy Technology Data Exchange (ETDEWEB)

    Schneidesch, Christophe R.; Zhang, Jinzhao; Ammirabile, Luca; Dalleur, Jean-Paul [Suez-Tractebel Engineering, Avenue Ariane 7, B-1200 Brussels (Belgium)

    2006-07-01

    coupled thermal hydraulic-neutronic transient calculations allow realistic simulations and hence better understanding the key physical phenomena. The TE coupled code package will be applied to develop coupled analysis methodologies for integrated safety analysis of other PWR accidents. (authors)

  7. An integrative review of the methodology and findings regarding dietary adherence in end stage kidney disease.

    Science.gov (United States)

    Lambert, Kelly; Mullan, Judy; Mansfield, Kylie

    2017-10-23

    Dietary modification is an important component of the management of end stage kidney disease (ESKD). The diet for ESKD involves modifying energy and protein intake, and altering sodium, phosphate, potassium and fluid intake. There have been no comprehensive reviews to date on this topic. The aims of this integrative review were to (i) describe the methods used to measure dietary adherence (ii) determine the rate of dietary adherence and (iii) describe factors associated with dietary adherence in ESKD. The Web of Science and Scopus databases were searched using the search terms 'adherence' and 'end stage kidney disease'. Of the 787 potentially eligible papers retrieved, 60 papers of 24,743 patients were included in this review. Of these papers, 44 reported the rate of dietary adherence and 44 papers described factors associated with adherence. Most of the evidence regarding dietary adherence is derived from studies of hemodialysis patients (72% of patients). The most common method of measuring dietary adherence in ESKD was subjective techniques (e.g. food diaries or adherence questionnaires). This was followed by indirect methods (e.g. serum potassium, phosphate or interdialytic weight gain). The weighted mean adherence rate to ESKD dietary recommendations was 31.5% and 68.5% for fluid recommendations. Adherence to protein, sodium, phosphate, and potassium recommendations were highly variable due to differences in measurement methods used, and were often derived from a limited evidence base. Socioeconomic status, age, social support and self-efficacy were associated with dietary adherence. However, factors such as taste, the impact of the diet on social eating occasions; and dietetic staffing also appear to play a role in dietary adherence. Dietary adherence rates in people with ESKD are suboptimal. Further research is required on dietary adherence in patients with ESKD from different social, educational, economic and ethnic groups. This research may identify other

  8. Integrated detoxification methodology of hazardous phenolic wastewaters in environmentally based trickle-bed reactors: Experimental investigation and CFD simulation

    International Nuclear Information System (INIS)

    Lopes, Rodrigo J.G.; Almeida, Teresa S.A.; Quinta-Ferreira, Rosa M.

    2011-01-01

    Centralized environmental regulations require the use of efficient detoxification technologies for the secure disposal of hazardous wastewaters. Guided by federal directives, existing plants need reengineering activities and careful analysis to improve their overall effectiveness and to become environmentally friendly. Here, we illustrate the application of an integrated methodology which encompasses the experimental investigation of catalytic wet air oxidation and CFD simulation of trickle-bed reactors. As long as trickle-bed reactors are determined by the flow environment coupled with chemical kinetics, first, on the optimization of prominent numerical solution parameters, the CFD model was validated with experimental data taken from a trickle bed pilot plant specifically designed for the catalytic wet oxidation of phenolic wastewaters. Second, several experimental and computational runs were carried out under unsteady-state operation to evaluate the dynamic performance addressing the TOC concentration and temperature profiles. CFD computations of total organic carbon conversion were found to agree better with experimental data at lower temperatures. Finally, the comparison of test data with simulation results demonstrated that this integrated framework was able to describe the mineralization of organic matter in trickle beds and the validated consequence model can be exploited to promote cleaner remediation technologies of contaminated waters.

  9. Integrated detoxification methodology of hazardous phenolic wastewaters in environmentally based trickle-bed reactors: Experimental investigation and CFD simulation.

    Science.gov (United States)

    Lopes, Rodrigo J G; Almeida, Teresa S A; Quinta-Ferreira, Rosa M

    2011-05-15

    Centralized environmental regulations require the use of efficient detoxification technologies for the secure disposal of hazardous wastewaters. Guided by federal directives, existing plants need reengineering activities and careful analysis to improve their overall effectiveness and to become environmentally friendly. Here, we illustrate the application of an integrated methodology which encompasses the experimental investigation of catalytic wet air oxidation and CFD simulation of trickle-bed reactors. As long as trickle-bed reactors are determined by the flow environment coupled with chemical kinetics, first, on the optimization of prominent numerical solution parameters, the CFD model was validated with experimental data taken from a trickle bed pilot plant specifically designed for the catalytic wet oxidation of phenolic wastewaters. Second, several experimental and computational runs were carried out under unsteady-state operation to evaluate the dynamic performance addressing the TOC concentration and temperature profiles. CFD computations of total organic carbon conversion were found to agree better with experimental data at lower temperatures. Finally, the comparison of test data with simulation results demonstrated that this integrated framework was able to describe the mineralization of organic matter in trickle beds and the validated consequence model can be exploited to promote cleaner remediation technologies of contaminated waters. Copyright © 2011 Elsevier B.V. All rights reserved.

  10. A quality control method by ultrasonic vibration energy and diagnosis system at trimming process

    International Nuclear Information System (INIS)

    Suh, Chang Min; Song, Gil Ho; Pyoun, Young Shik

    2007-01-01

    In this paper, the characteristics in mechanical properties of ultrasonic cold forging treatment (UCFT) used for the trimming knife and the effects of ultrasonic vibration energy (UVE) into the trimming process on the state of the strip cutting face were studied. And a diagnosis system to quality control for trimming knife and strip cutting face was developed and installed in plant. By the plant application of UCFT, service life of knife was more increased over 100% than that of conventional knife and using the developed diagnosis system, the knife breakage and saw ear have been perfectly detected and quality control of trimming face is effectively obtained

  11. TRIM45 negatively regulates NF-κB-mediated transcription and suppresses cell proliferation

    International Nuclear Information System (INIS)

    Shibata, Mio; Sato, Tomonobu; Nukiwa, Ryota; Ariga, Tadashi; Hatakeyama, Shigetsugu

    2012-01-01

    Highlights: ► NF-κB plays an important role in cell survival and carcinogenesis. ► TRIM45 negatively regulates TNFα-induced NF-κB-mediated transcription. ► TRIM45 overexpression suppresses cell growth. ► TRIM45 acts as a repressor for the NF-κB signal and regulates cell growth. -- Abstract: The NF-κB signaling pathway plays an important role in cell survival, immunity, inflammation, carcinogenesis, and organogenesis. Activation of NF-κB is regulated by several posttranslational modifications including phosphorylation, neddylation and ubiquitination. The NF-κB signaling pathway is activated by two distinct signaling mechanisms and is strictly modulated by the ubiquitin–proteasome system. It has been reported that overexpression of TRIM45, one of the TRIM family ubiquitin ligases, suppresses transcriptional activities of Elk-1 and AP-1, which are targets of the MAPK signaling pathway. In this study, we showed that TRIM45 also negatively regulates TNFα-induced NF-κB-mediated transcription by a luciferase reporter assay and that TRIM45 lacking a RING domain also has an activity to inhibit the NF-κB signal. Moreover, we found that TRIM45 overexpression suppresses cell growth. These findings suggest that TRIM45 acts as a repressor for the NF-κB signal and regulates cell growth.

  12. Microstructural investigations of the trimmed edge of DP980 steel sheets

    Science.gov (United States)

    Bhattacharya, S.; Green, D. E.; Sohmshetty, R.; Alpas, A. T.

    2017-10-01

    In order to reduce vehicle weight while maintaining crashworthiness, advanced high strength steels (AHSSs), such as DP980, are extensively used for manufacturing automotive body components. During trimming operations, the high tensile strength of DP980 sheets tends to cause damage of the trim edge of D2 die inserts, which result in deterioration of the edge quality. The objective of this work is to study the damage microstructures at the trimmed edge of DP980 steel sheets as a function of the number of trimming cycles. A mechanical press equipped with AISI D2 tool steel inserts was used to continuously trim 1.4 mm thick sheets of DP980 at a rate of 30 strokes/min. Cross-sectional SEM images of the trimmed edges revealed that the sheared edge quality of the DP980 sheets decreased, indicated by an increase in the burr width, with an increase in the number of trims from 40,000 to 70,000. Plastic strains were estimated using the displacements of the martensite plates within plastic flow fields of ferrite. Site-specific cross-sectional TEM samples, excised from the trimmed edge using the in-situ `lift-out' technique by focused ion-beam (FIB)-milling, revealed cracking at the ferrite/martensite interfaces after 70,000 cycles indicating an increase in the depth of deformation zone possibly due to trimming with a chipped and blunted die edge.

  13. Enviro-HIRLAM online integrated meteorology–chemistry modelling system: strategy, methodology, developments and applications (v7.2

    Directory of Open Access Journals (Sweden)

    A. Baklanov

    2017-08-01

    Full Text Available The Environment – High Resolution Limited Area Model (Enviro-HIRLAM is developed as a fully online integrated numerical weather prediction (NWP and atmospheric chemical transport (ACT model for research and forecasting of joint meteorological, chemical and biological weather. The integrated modelling system is developed by the Danish Meteorological Institute (DMI in collaboration with several European universities. It is the baseline system in the HIRLAM Chemical Branch and used in several countries and different applications. The development was initiated at DMI more than 15 years ago. The model is based on the HIRLAM NWP model with online integrated pollutant transport and dispersion, chemistry, aerosol dynamics, deposition and atmospheric composition feedbacks. To make the model suitable for chemical weather forecasting in urban areas, the meteorological part was improved by implementation of urban parameterisations. The dynamical core was improved by implementing a locally mass-conserving semi-Lagrangian numerical advection scheme, which improves forecast accuracy and model performance. The current version (7.2, in comparison with previous versions, has a more advanced and cost-efficient chemistry, aerosol multi-compound approach, aerosol feedbacks (direct and semi-direct on radiation and (first and second indirect effects on cloud microphysics. Since 2004, the Enviro-HIRLAM has been used for different studies, including operational pollen forecasting for Denmark since 2009 and operational forecasting atmospheric composition with downscaling for China since 2017. Following the main research and development strategy, further model developments will be extended towards the new NWP platform – HARMONIE. Different aspects of online coupling methodology, research strategy and possible applications of the modelling system, and fit-for-purpose model configurations for the meteorological and air quality communities are discussed.

  14. Response Surface Methodology and Aspen Plus Integration for the Simulation of the Catalytic Steam Reforming of Ethanol

    Directory of Open Access Journals (Sweden)

    Bernay Cifuentes

    2017-01-01

    Full Text Available The steam reforming of ethanol (SRE on a bimetallic RhPt/CeO2 catalyst was evaluated by the integration of Response Surface Methodology (RSM and Aspen Plus (version 9.0, Aspen Tech, Burlington, MA, USA, 2016. First, the effect of the Rh–Pt weight ratio (1:0, 3:1, 1:1, 1:3, and 0:1 on the performance of SRE on RhPt/CeO2 was assessed between 400 to 700 °C with a stoichiometric steam/ethanol molar ratio of 3. RSM enabled modeling of the system and identification of a maximum of 4.2 mol H2/mol EtOH (700 °C with the Rh0.4Pt0.4/CeO2 catalyst. The mathematical models were integrated into Aspen Plus through Excel in order to simulate a process involving SRE, H2 purification, and electricity production in a fuel cell (FC. An energy sensitivity analysis of the process was performed in Aspen Plus, and the information obtained was used to generate new response surfaces. The response surfaces demonstrated that an increase in H2 production requires more energy consumption in the steam reforming of ethanol. However, increasing H2 production rebounds in more energy production in the fuel cell, which increases the overall efficiency of the system. The minimum H2 yield needed to make the system energetically sustainable was identified as 1.2 mol H2/mol EtOH. According to the results of the integration of RSM models into Aspen Plus, the system using Rh0.4Pt0.4/CeO2 can produce a maximum net energy of 742 kJ/mol H2, of which 40% could be converted into electricity in the FC (297 kJ/mol H2 produced. The remaining energy can be recovered as heat.

  15. Body-induced vortical flows: a common mechanism for self-corrective trimming control in boxfishes.

    Science.gov (United States)

    Bartol, Ian K; Gharib, Morteza; Webb, Paul W; Weihs, Daniel; Gordon, Malcolm S

    2005-01-01

    Boxfishes (Teleostei: Ostraciidae) are marine fishes having rigid carapaces that vary significantly among taxa in their shapes and structural ornamentation. We showed previously that the keels of the carapace of one species of tropical boxfish, the smooth trunkfish, produce leading edge vortices (LEVs) capable of generating self-correcting trimming forces during swimming. In this paper we show that other tropical boxfishes with different carapace shapes have similar capabilities. We conducted a quantitative study of flows around the carapaces of three morphologically distinct boxfishes (spotted boxfish, scrawled cowfish and buffalo trunkfish) using stereolithographic models and three separate but interrelated analytical approaches: digital particle image velocimetry (DPIV), pressure distribution measurements, and force balance measurements. The ventral keels of all three forms produced LEVs that grew in circulation along the bodies, resembling the LEVs produced around delta-winged aircraft. These spiral vortices formed above the keels and increased in circulation as pitch angle became more positive, and formed below the keels and increased in circulation as pitch angle became more negative. Vortices also formed along the eye ridges of all boxfishes. In the spotted boxfish, which is largely trapezoidal in cross section, consistent dorsal vortex growth posterior to the eye ridge was also present. When all three boxfishes were positioned at various yaw angles, regions of strongest concentrated vorticity formed in far-field locations of the carapace compared with near-field areas, and vortex circulation was greatest posterior to the center of mass. In general, regions of localized low pressure correlated well with regions of attached, concentrated vorticity, especially around the ventral keels. Although other features of the carapace also affect flow patterns and pressure distributions in different ways, the integrated effects of the flows were consistent for all forms

  16. Human factors analysis and design methods for nuclear waste retrieval systems. Human factors design methodology and integration plan

    Energy Technology Data Exchange (ETDEWEB)

    Casey, S.M.

    1980-06-01

    The purpose of this document is to provide an overview of the recommended activities and methods to be employed by a team of human factors engineers during the development of a nuclear waste retrieval system. This system, as it is presently conceptualized, is intended to be used for the removal of storage canisters (each canister containing a spent fuel rod assembly) located in an underground salt bed depository. This document, and the others in this series, have been developed for the purpose of implementing human factors engineering principles during the design and construction of the retrieval system facilities and equipment. The methodology presented has been structured around a basic systems development effort involving preliminary development, equipment development, personnel subsystem development, and operational test and evaluation. Within each of these phases, the recommended activities of the human engineering team have been stated, along with descriptions of the human factors engineering design techniques applicable to the specific design issues. Explicit examples of how the techniques might be used in the analysis of human tasks and equipment required in the removal of spent fuel canisters have been provided. Only those techniques having possible relevance to the design of the waste retrieval system have been reviewed. This document is intended to provide the framework for integrating human engineering with the rest of the system development effort. The activities and methodologies reviewed in this document have been discussed in the general order in which they will occur, although the time frame (the total duration of the development program in years and months) in which they should be performed has not been discussed.

  17. SafeNet: a methodology for integrating general-purpose unsafe devices in safe-robot rehabilitation systems.

    Science.gov (United States)

    Vicentini, Federico; Pedrocchi, Nicola; Malosio, Matteo; Molinari Tosatti, Lorenzo

    2014-09-01

    Robot-assisted neurorehabilitation often involves networked systems of sensors ("sensory rooms") and powerful devices in physical interaction with weak users. Safety is unquestionably a primary concern. Some lightweight robot platforms and devices designed on purpose include safety properties using redundant sensors or intrinsic safety design (e.g. compliance and backdrivability, limited exchange of energy). Nonetheless, the entire "sensory room" shall be required to be fail-safe and safely monitored as a system at large. Yet, sensor capabilities and control algorithms used in functional therapies require, in general, frequent updates or re-configurations, making a safety-grade release of such devices hardly sustainable in cost-effectiveness and development time. As such, promising integrated platforms for human-in-the-loop therapies could not find clinical application and manufacturing support because of lacking in the maintenance of global fail-safe properties. Under the general context of cross-machinery safety standards, the paper presents a methodology called SafeNet for helping in extending the safety rate of Human Robot Interaction (HRI) systems using unsafe components, including sensors and controllers. SafeNet considers, in fact, the robotic system as a device at large and applies the principles of functional safety (as in ISO 13489-1) through a set of architectural procedures and implementation rules. The enabled capability of monitoring a network of unsafe devices through redundant computational nodes, allows the usage of any custom sensors and algorithms, usually planned and assembled at therapy planning-time rather than at platform design-time. A case study is presented with an actual implementation of the proposed methodology. A specific architectural solution is applied to an example of robot-assisted upper-limb rehabilitation with online motion tracking. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

  18. Human factors analysis and design methods for nuclear waste retrieval systems. Human factors design methodology and integration plan

    International Nuclear Information System (INIS)

    Casey, S.M.

    1980-06-01

    The purpose of this document is to provide an overview of the recommended activities and methods to be employed by a team of human factors engineers during the development of a nuclear waste retrieval system. This system, as it is presently conceptualized, is intended to be used for the removal of storage canisters (each canister containing a spent fuel rod assembly) located in an underground salt bed depository. This document, and the others in this series, have been developed for the purpose of implementing human factors engineering principles during the design and construction of the retrieval system facilities and equipment. The methodology presented has been structured around a basic systems development effort involving preliminary development, equipment development, personnel subsystem development, and operational test and evaluation. Within each of these phases, the recommended activities of the human engineering team have been stated, along with descriptions of the human factors engineering design techniques applicable to the specific design issues. Explicit examples of how the techniques might be used in the analysis of human tasks and equipment required in the removal of spent fuel canisters have been provided. Only those techniques having possible relevance to the design of the waste retrieval system have been reviewed. This document is intended to provide the framework for integrating human engineering with the rest of the system development effort. The activities and methodologies reviewed in this document have been discussed in the general order in which they will occur, although the time frame (the total duration of the development program in years and months) in which they should be performed has not been discussed

  19. TRIM8 downregulation in glioma affects cell proliferation and it is associated with patients survival

    International Nuclear Information System (INIS)

    Micale, Lucia; Fusco, Carmela; Fontana, Andrea; Barbano, Raffaela; Augello, Bartolomeo; De Nittis, Pasquelena; Copetti, Massimiliano; Pellico, Maria Teresa; Mandriani, Barbara; Cocciadiferro, Dario; Parrella, Paola; Fazio, Vito Michele; Dimitri, Lucia Maria Cecilia; D’Angelo, Vincenzo; Novielli, Chiara; Larizza, Lidia; Daga, Antonio; Merla, Giuseppe

    2015-01-01

    Human gliomas are a heterogeneous group of primary malignant brain tumors whose molecular pathogenesis is not yet solved. In this regard, a major research effort has been directed at identifying novel specific glioma-associated genes. Here, we investigated the effect of TRIM8 gene in glioma. TRIM8 transcriptional level was profiled in our own glioma cases collection by qPCR and confirmed in the independent TCGA glioma cohort. The association between TRIM8 expression and Overall Survival and Progression-free Survival in TCGA cohort was determined by using uni-multivariable Cox regression analysis. The effect of TRIM8 on patient glioma cell proliferation was evaluated by performing MTT and clonogenic assays. The mechanisms causing the reduction of TRIM8 expression were explored by using qPCR and in vitro assays. We showed that TRIM8 expression correlates with unfavorable clinical outcome in glioma patients. We found that a restored TRIM8 expression induced a significant reduction of clonogenic potential in U87MG and patient’s glioblastoma cells. Finally we provide experimental evidences showing that miR-17 directly targets the 3′ UTR of TRIM8 and post-transcriptionally represses the expression of TRIM8. Our study provides evidences that TRIM8 may participate in the carcinogenesis and progression of glioma and that the transcriptional repression of TRIM8 might have potential value for predicting poor prognosis in glioma patients. The online version of this article (doi:10.1186/s12885-015-1449-9) contains supplementary material, which is available to authorized users

  20. SUMO-interacting motifs of human TRIM5α are important for antiviral activity.

    Directory of Open Access Journals (Sweden)

    Gloria Arriagada

    2011-04-01

    Full Text Available Human TRIM5α potently restricts particular strains of murine leukemia viruses (the so-called N-tropic strains but not others (the B- or NB-tropic strains during early stages of infection. We show that overexpression of SUMO-1 in human 293T cells, but not in mouse MDTF cells, profoundly blocks N-MLV infection. This block is dependent on the tropism of the incoming virus, as neither B-, NB-, nor the mutant R110E of N-MLV CA (a B-tropic switch are affected by SUMO-1 overexpression. The block occurred prior to reverse transcription and could be abrogated by large amounts of restricted virus. Knockdown of TRIM5α in 293T SUMO-1-overexpressing cells resulted in ablation of the SUMO-1 antiviral effects, and this loss of restriction could be restored by expression of a human TRIM5α shRNA-resistant plasmid. Amino acid sequence analysis of human TRIM5α revealed a consensus SUMO conjugation site at the N-terminus and three putative SUMO interacting motifs (SIMs in the B30.2 domain. Mutations of the TRIM5α consensus SUMO conjugation site did not affect the antiviral activity of TRIM5α in any of the cell types tested. Mutation of the SIM consensus sequences, however, abolished TRIM5α antiviral activity against N-MLV. Mutation of lysines at a potential site of SUMOylation in the CA region of the Gag gene reduced the SUMO-1 block and the TRIM5α restriction of N-MLV. Our data suggest a novel aspect of TRIM5α-mediated restriction, in which the presence of intact SIMs in TRIM5α, and also the SUMO conjugation of CA, are required for restriction. We propose that at least a portion of the antiviral activity of TRIM5α is mediated through the binding of its SIMs to SUMO-conjugated CA.

  1. Marrying Step Feed with Secondary Clarifier Improvements to Significantly Increase Peak Wet Weather Treatment Capacity: An Integrated Methodology.

    Science.gov (United States)

    Daigger, Glen T; Siczka, John S; Smith, Thomas F; Frank, David A; McCorquodale, J A

    2017-08-01

      The need to increase the peak wet weather secondary treatment capacity of the City of Akron, Ohio, Water Reclamation Facility (WRF) provided the opportunity to test an integrated methodology for maximizing the peak wet weather secondary treatment capacity of activated sludge systems. An initial investigation, consisting of process modeling of the secondary treatment system and computational fluid dynamics (CFD) analysis of the existing relatively shallow secondary clarifiers (3.3 and 3.7 m sidewater depth in 30.5 m diameter units), indicated that a significant increase in capacity from 416 000 to 684 000 m3/d or more was possible by adding step feed capabilities to the existing bioreactors and upgrading the existing secondary clarifiers. One of the six treatment units at the WRF was modified, and an extensive 2-year testing program was conducted to determine the total peak wet weather secondary treatment capacity achievable. The results demonstrated that a peak wet weather secondary treatment capacity approaching 974 000 m3/d is possible as long as secondary clarifier solids and hydraulic loadings could be separately controlled using the step feed capability provided. Excellent sludge settling characteristics are routinely experienced at the City of Akron WRF, raising concerns that the identified peak wet weather secondary treatment capacity could not be maintained should sludge settling characteristics deteriorate for some reason. Computational fluid dynamics analysis indicated that the impact of the deterioration of sludge settling characteristics could be mitigated and the identified peak wet weather secondary treatment capacity maintained by further use of the step feed capability provided to further reduce secondary clarifier solids loading rates at the identified high surface overflow rates. The results also demonstrated that effluent limits not only for total suspended solids (TSS) and five-day carbonaceous biochemical oxygen demand (cBOD5) could be

  2. Steps in creating a methodology for interpreting a geodiversity element -integrating a geodiversity element in the popular knowledge

    Science.gov (United States)

    Toma, Cristina; Andrasanu, Alexandru

    2017-04-01

    Conserving geodiversity and especially geological heritage is not very well integrated in the general knowledge as biodiversity is, for example. Keeping that in mind we are trying, through this research, to find a better way of transmitting a geological process to the general public. The means to integrate a geodiversity element in the popular knowledge is through interpretation. Interpretation "translates" the scientific information into a common language with very well known facts by the general public. The purpose of this paper is creating a framework for a methodology necessary in interpreting a geodiversity element - salt - in Buzau Land Geopark. We will approach the salt subject through a scheme in order to have a general view of the process and to better understand and explain it to the general public. We will look into the subject from three scientific points of view: GEODIVERSITY, ANTHROPOLOGY, and the SOCIO-ECONOMICAL aspect. Each of these points of view or domains will be divided into themes. For GEODIVERSITY we will have the following themes: Formation, Accumulation, Diapirism process, Chemical formula, Landscape (here we will include also the specific biodiversity with the halophile plants), Landforms, Hazard. For ANTHROPOLOGY will contain themes of tangible and intangible heritage like: Salt symbolistic, Stories and ritual usage, Recipes, How the knowledge is transmitted. The SOCIO-ECONOMIC aspect will be reflected through themes like: Extractive methods, Usage, Interdictions, Taxes, Commercial exchanges. Each theme will have a set of keywords that will be described and each one will be at the base of the elements that together will form the interpretation of the geodiversity element - the salt. The next step will be to clearly set the scope of the interpretation, to which field of expertise is our interpretation process addressed: Education (Undergraduate or post-graduate Students), Science, Geotourism, Entrepreneurship. After putting together the

  3. Finite Element Modelling and Analysis of Damage Detection Methodology in Piezo Electric Sensor and Actuator Integrated Sandwich Cantilever Beam

    Science.gov (United States)

    Pradeep, K. R.; Thomas, A. M.; Basker, V. T.

    2018-03-01

    Structural health monitoring (SHM) is an essential component of futuristic civil, mechanical and aerospace structures. It detects the damages in system or give warning about the degradation of structure by evaluating performance parameters. This is achieved by the integration of sensors and actuators into the structure. Study of damage detection process in piezoelectric sensor and actuator integrated sandwich cantilever beam is carried out in this paper. Possible skin-core debond at the root of the cantilever beam is simulated and compared with undamaged case. The beam is actuated using piezoelectric actuators and performance differences are evaluated using Polyvinylidene fluoride (PVDF) sensors. The methodology utilized is the voltage/strain response of the damaged versus undamaged beam against transient actuation. Finite element model of piezo-beam is simulated in ANSYSTM using 8 noded coupled field element, with nodal degrees of freedoms are translations in the x, y directions and voltage. An aluminium sandwich beam with a length of 800mm, thickness of core 22.86mm and thickness of skin 0.3mm is considered. Skin-core debond is simulated in the model as unmerged nodes. Reduction in the fundamental frequency of the damaged beam is found to be negligible. But the voltage response of the PVDF sensor under transient excitation shows significantly visible change indicating the debond. Piezo electric based damage detection system is an effective tool for the damage detection of aerospace and civil structural system having inaccessible/critical locations and enables online monitoring possibilities as the power requirement is minimal.

  4. Theoretical and methodological elements for integrating ethics as a foundation into the education of professional and design disciplines.

    Science.gov (United States)

    d'Anjou, Philippe

    2004-04-01

    The paper addresses the integration of ethics into professional education related to the disciplines responsible for the conception and creation of the artificial (artefactual or technology). The ontological-epistemological paradigm of those disciplines is understood within the frame of the sciences of the artificial as established by Herbert Simon (1969). According to that paradigm, those sciences include disciplines not only related to the production of artefacts (technology), such as engineering, architecture, industrial design, etc, but also disciplines related to devised courses of action aimed at changing existing situations into preferred ones, like medicine, law, education, etc. They are centered on intentional action and at their core is the activity of design, which is their common foundation and attitude, or their common culture. The science of design becomes the broader foundational discipline for any professions engaged in the intentional transformation of the world. The main distinction between design disciplines and scientific ones rests on the object-project dichotomy. Indeed, contrary to Science that sees the world as an object to be observed, Design sees the world as a project and acts upon the world through projects, which are grounded in intentions, ends, and values. Design disciplines are meant to transform the world, or part of it, and are teleological. Being so, they are embodied in an act that is ethical and their ontology-epistemology must be addressed also through practical reason to resituate all professional disciplines according to their involved nature. The paper introduces theoretical, methodological, and ethical elements to establish a model that integrates ethics into the education of the professional disciplines, design-based disciplines, responsible for the creation of the artificial, artefactual or technological, world. The model is articulated around the notions of ethical engagement and responsibility through the act of design

  5. Effect of two trimming methods of dairy cattle on concrete or rubber-covered slatted floors

    NARCIS (Netherlands)

    Ouweltjes, W.; Holzhauer, M.; Tol, van der P.P.J.; Werf, van der J.T.N.

    2009-01-01

    This study monitored claw health, claw conformation, locomotion, activity, and step traits of cows from a single dairy herd that were trimmed according to the standard Dutch method or with an alternative "concave" trimming method. Half of the cows were kept in a stall section with concrete slatted

  6. Nuclear TRIM25 Specifically Targets Influenza Virus Ribonucleoproteins to Block the Onset of RNA Chain Elongation.

    Science.gov (United States)

    Meyerson, Nicholas R; Zhou, Ligang; Guo, Yusong R; Zhao, Chen; Tao, Yizhi J; Krug, Robert M; Sawyer, Sara L

    2017-11-08

    TRIM25 is an E3 ubiquitin ligase that activates RIG-I to promote the antiviral interferon response. The NS1 protein from all strains of influenza A virus binds TRIM25, although not all virus strains block the interferon response, suggesting alternative mechanisms for TRIM25 action. Here we present a nuclear role for TRIM25 in specifically restricting influenza A virus replication. TRIM25 inhibits viral RNA synthesis through a direct mechanism that is independent of its ubiquitin ligase activity and the interferon pathway. This activity can be inhibited by the viral NS1 protein. TRIM25 inhibition of viral RNA synthesis results from its binding to viral ribonucleoproteins (vRNPs), the structures containing individual viral RNA segments, the viral polymerase, and multiple viral nucleoproteins. TRIM25 binding does not inhibit initiation of capped-RNA-primed viral mRNA synthesis by the viral polymerase. Rather, the onset of RNA chain elongation is inhibited because TRIM25 prohibits the movement of RNA into the polymerase complex. Copyright © 2017 Elsevier Inc. All rights reserved.

  7. Genome-wide association study for claw disorders and trimming status in dairy cattle

    NARCIS (Netherlands)

    Spek, van der D.; Arendonk, van J.A.M.; Bovenhuis, H.

    2015-01-01

    Performing a genome-wide association study (GWAS) might add to a better understanding of the development of claw disorders and the need for trimming. Therefore, the aim of the current study was to perform a GWAS on claw disorders and trimming status and to validate the results for claw disorders

  8. Effect of Hardwood Sawmill Edging and Trimming Practices on Furniture Part Production

    Science.gov (United States)

    D. Earl Kline; Carmen Regalado; Eugene M. Wengert; Fred M. Lamb; Philip A. Araman

    1993-01-01

    In a recent edging and trimming study at three hardwood sawmills, it was observed that the lumber volume produced was approximately 10 percent less than would be necessary to make the most valuable lumber. Furthermore, the excess portion of wood that was removed from the edging and trimming process contained a large percentage of clear wood. In light of rising costs...

  9. A methodological approach to be used in integrated coastal zone management processes: the case of the Catalan Coast (Catalonia, Spain)

    Science.gov (United States)

    Sardá, Rafael; Avila, Conxita; Mora, Joan

    2005-02-01

    Since early 1999, we have been working on an environmental information system as a preliminary phase to develop the National Strategy of the Catalan Coast. Using the tourism industry as the main pressuring driver and the municipality as the territorial unit, we have compiled a vast amount of information that has been converted into an information platform for the general public, politicians, and public administrators. Working in close co-operation with the planning authorities of the Generalitat of Catalonia, we developed decision support tools as a methodological approach for coastal management. The decision support system is composed by: (a) the development of an environmental indicator-based report; (b) the use of a geographical information system (GIS); and (c) the incorporation of different types of graphical packages. These tools have been applied to the 70 municipalities of the Catalan Coast and a specific development of the system was carried out in the region of La Selva, municipalities of Blanes, Lloret de Mar, and Tossa de Mar (southern Costa Brava, Girona). The system has been designed to help coastal managers in Catalonia, and it is thought to be used in the process of developing the National Strategy for Integrated Coastal Zone Management (ICZM) of the Catalan Coast following the EC Recommendation (COM/00/545).

  10. Bioinspired methodology for preparing magnetic responsive chitosan beads to be integrated in a tubular bioreactor for biomedical applications.

    Science.gov (United States)

    Song, Wenlong; Oliveira, Mariana B; Sher, Praveen; Gil, Sara; Nóbrega, J Miguel; Mano, João F

    2013-08-01

    Magnetic responsive chitosan beads were prepared using a methodology inspired by the rolling of water droplets over lotus leaves. Liquid precursors containing chitosan and magnetic microparticles were dispensed in the form of spherical droplets and crosslinked with genipin over synthetic superhydrophobic surfaces. Scanning electronic microscopy, histology and micro-computed tomography were employed to characterize the structure of the prepared composite beads and the inner distribution of the magnetic particles. Cellular metabolic activity tests showed that fibroblasts-like (L929 cell line) can adhere and proliferate on the prepared chitosan beads. We hypothesize that such spherical biomaterials could be integrated in a new concept of tubular bioreactor. The magnetic beads can be immobilized by an external magnetic field at specific positions and may be transported along the bioreactor by the drag of the culture medium flow. The system behavior was also studied through numerical modeling, which allowed to identify the relative importance of the main parameters, and to conclude that the distance between carrier beads plays a major role on their interaction with the culture medium and, consequently, on the overall system performance. In an up-scaled version of this bioreactor, the herein presented system may comprise different chambers in serial or parallel configurations. This constitutes a simple way of preparing magnetic responsive beads combined with a new design of bioreactor, which may find application in biomedicine and biotechnology, including in cell expansion for tissue engineering or for the production of therapeutic proteins to be used in cell therapies.

  11. Integration of educational methods and physical settings: design guidelines for High/Scope methodology in pre-schools

    Directory of Open Access Journals (Sweden)

    Shirin Izadpanah

    2014-06-01

    Full Text Available Quality design and appropriate space organization in preschool settings can support preschool children's educational activities. Although the relationship between the well-being and development of children and physical settings has been emphasized by many early childhood researchers, there is still a need for theoretical design guidelines that are geared towards the improvement of this issue. This research focuses on High/Scope education and aims to shape a theoretical guideline that raises teachers' awareness about the potential of learning spaces and guides them to improve the quality of the physical spaces. To create a theoretical framework, reliable sources are investigated in the light of High/Scope education and the requirements of pre-school children educational spaces. Physical space characteristics, the preschool child's requirements and High/Scope methodology identified design inputs, design considerations and recommendations that shape the final guideline for spatial arrangement in a High/Scope setting are integrated. Discussions and suggestions in this research benefit both designers and High/ Scope teaching staff. Results help High/Scope teaching staff increase the quality of a space in an educational setting without having an architectural background. The theoretical framework of the research allows designers to consider key features and users' possible activities in High/ Scope settings and shape their designs accordingly.

  12. Integration of Methodologies for the Evaluation of Offer Curves in Energy and Capacity Markets through Energy Efficiency and Demand Response

    Directory of Open Access Journals (Sweden)

    Antonio Gabaldón

    2018-02-01

    Full Text Available The objectives of improving the efficiency, and integration, of renewable sources by 2030–2050 are complex in practice and should be linked to an increase of demand-side flexibility. The main challenges to achieving this flexibility are the lack of incentives and an adequate framework. For instance, customers’ revenue is usually low, the volatility of prices is high and there is not any practical feedback to customers from smart meters. The possibility of increasing customer revenue could reduce the uncertainty with respect to economic concerns, improving investments in efficiency, enabling technology and thus, engaging more customers in these policies. This objective could be achieved by the participation of customers in several markets. Moreover, Demand Response and Energy Efficiency can share ICT technologies but this participation needs to perform an aggregation of demand. The idea of this paper is to present some methodologies for facilitating the definition and evaluation of energy versus cost curves; and subsequently to estimate potential revenues due to Demand Response. This can be accomplished by models that estimate: demand and energy aggregation; economic opportunities and benefits; impacts on customer convenience; customer feedback and price analysis. By doing so, we would have comprehensive information that can help customers and aggregators to define energy packages and their monetary value with the objective of fostering their market participation.

  13. Bioinspired methodology for preparing magnetic responsive chitosan beads to be integrated in a tubular bioreactor for biomedical applications

    International Nuclear Information System (INIS)

    Song, Wenlong; Oliveira, Mariana B; Sher, Praveen; Gil, Sara; Mano, João F; Nóbrega, J Miguel

    2013-01-01

    Magnetic responsive chitosan beads were prepared using a methodology inspired by the rolling of water droplets over lotus leaves. Liquid precursors containing chitosan and magnetic microparticles were dispensed in the form of spherical droplets and crosslinked with genipin over synthetic superhydrophobic surfaces. Scanning electronic microscopy, histology and micro-computed tomography were employed to characterize the structure of the prepared composite beads and the inner distribution of the magnetic particles. Cellular metabolic activity tests showed that fibroblasts-like (L929 cell line) can adhere and proliferate on the prepared chitosan beads. We hypothesize that such spherical biomaterials could be integrated in a new concept of tubular bioreactor. The magnetic beads can be immobilized by an external magnetic field at specific positions and may be transported along the bioreactor by the drag of the culture medium flow. The system behavior was also studied through numerical modeling, which allowed to identify the relative importance of the main parameters, and to conclude that the distance between carrier beads plays a major role on their interaction with the culture medium and, consequently, on the overall system performance. In an up-scaled version of this bioreactor, the herein presented system may comprise different chambers in serial or parallel configurations. This constitutes a simple way of preparing magnetic responsive beads combined with a new design of bioreactor, which may find application in biomedicine and biotechnology, including in cell expansion for tissue engineering or for the production of therapeutic proteins to be used in cell therapies. (paper)

  14. An application of the value tree analysis methodology within the integrated risk informed decision making for the nuclear facilities

    International Nuclear Information System (INIS)

    Borysiewicz, Mieczysław; Kowal, Karol; Potempski, Sławomir

    2015-01-01

    A new framework of integrated risk informed decision making (IRIDM) has been recently developed in order to improve the risk management of the nuclear facilities. IRIDM is a process in which qualitatively different inputs, corresponding to different types of risk, are jointly taken into account. However, the relative importance of the IRIDM inputs and their influence on the decision to be made is difficult to be determined quantitatively. An improvement of this situation can be achieved by application of the Value Tree Analysis (VTA) methods. The aim of this article is to present the VTA methodology in the context of its potential usage in the decision making on nuclear facilities. The benefits of the VTA application within the IRIDM process were identified while making the decision on fuel conversion of the research reactor MARIA. - Highlights: • New approach to risk informed decision making on nuclear facilities was postulated. • Value tree diagram was developed for decision processes on nuclear installations. • An experiment was performed to compare the new approach with the standard one. • Benefits of the new approach were reached in fuel conversion of a research reactor. • The new approach makes the decision making process more transparent and auditable

  15. Genetic parameters for claw disorders and the effect of preselecting cows for trimming.

    Science.gov (United States)

    van der Spek, D; van Arendonk, J A M; Vallée, A A A; Bovenhuis, H

    2013-09-01

    Claw disorders are important traits relevant to dairy cattle breeding from an economical and welfare point of view. Selection for reduced claw disorders can be based on hoof trimmer records. Typically, not all cows in a herd are trimmed. Our objectives were to estimate heritabilities and genetic correlations for claw disorders and investigate the effect of selecting cows for trimming. The data set contained 50,238 cows, of which 20,474 cows had at least one claw trimming record, with a total of 29,994 records. Six claw trimmers scored 14 different claw disorders: abscess (AB), corkscrew claw (CC), (inter-)digital dermatitis or heel erosion (DER), double sole (DS), hardship groove (HG), interdigital hyperplasia (IH), interdigital phlegmon (IP), sand crack (SC), super-foul (SF), sole hemorrhage (SH), sole injury (SI), sole ulcer (SU), white line separation (WLS), yellow discoloration of the sole (YD), and a combined claw disorder trait. Frequencies of the claw disorders for trimmed cows ranged from 0.1% (CC, YD, HG) to 23.8% (DER). More than half of the cows scored had at least one claw disorder. Heritability on the observed scale ranged from 0.02 (DS, SH) to 0.14 (IH) and on the underlying scale from 0.05 to 0.43 in trimmed cows. Genetic correlations between laminitis-related claw disorders were moderate to high, and the same was found for hygiene-related claw disorders. The effect of selecting cows for trimming was first investigated by including untrimmed cows in the analyses and assuming they were not affected by claw disorders. Heritabilities on the underlying scale showed only minor changes. Second, different subsets of the data were created based on the percentage of trimmed cows in the herd. Heritabilities for IH, DER, and SU tended to decrease when a higher percentage of cows in the herd were trimmed. Finally, a bivariate model with a claw disorder and the trait "trimming status" was used, but heritabilities were similar. Heritability for trimming status was

  16. A methodological study of environmental simulation in architecture and engineering. Integrating daylight and thermal performance across the urban and building scales

    DEFF Research Database (Denmark)

    Sattrup, Peter Andreas; Strømann-Andersen, Jakob Bjørn

    2011-01-01

    This study presents a methodological and conceptual framework that allows for the integration and creation of knowledge across professional borders in the field of environmental simulation. The framework has been developed on the basis of interviews with leading international practitioners, key...... in pointing out the need for improving metrics, software and not least the performance of the built environment itself....

  17. TRIM15 is a focal adhesion protein that regulates focal adhesion disassembly

    Science.gov (United States)

    Uchil, Pradeep D.; Pawliczek, Tobias; Reynolds, Tracy D.; Ding, Siyuan; Hinz, Angelika; Munro, James B.; Huang, Fang; Floyd, Robert W.; Yang, Haitao; Hamilton, William L.; Bewersdorf, Joerg; Xiong, Yong; Calderwood, David A.; Mothes, Walther

    2014-01-01

    ABSTRACT Focal adhesions are macromolecular complexes that connect the actin cytoskeleton to the extracellular matrix. Dynamic turnover of focal adhesions is crucial for cell migration. Paxillin is a multi-adaptor protein that plays an important role in regulating focal adhesion dynamics. Here, we identify TRIM15, a member of the tripartite motif protein family, as a paxillin-interacting factor and a component of focal adhesions. TRIM15 localizes to focal contacts in a myosin-II-independent manner by an interaction between its coiled-coil domain and the LD2 motif of paxillin. Unlike other focal adhesion proteins, TRIM15 is a stable focal adhesion component with restricted mobility due to its ability to form oligomers. TRIM15-depleted cells display impaired cell migration and reduced focal adhesion disassembly rates, in addition to enlarged focal adhesions. Thus, our studies demonstrate a cellular function for TRIM15 as a regulatory component of focal adhesion turnover and cell migration. PMID:25015296

  18. Trimming of mammalian transcriptional networks using network component analysis

    Directory of Open Access Journals (Sweden)

    Liao James C

    2010-10-01

    Full Text Available Abstract Background Network Component Analysis (NCA has been used to deduce the activities of transcription factors (TFs from gene expression data and the TF-gene binding relationship. However, the TF-gene interaction varies in different environmental conditions and tissues, but such information is rarely available and cannot be predicted simply by motif analysis. Thus, it is beneficial to identify key TF-gene interactions under the experimental condition based on transcriptome data. Such information would be useful in identifying key regulatory pathways and gene markers of TFs in further studies. Results We developed an algorithm to trim network connectivity such that the important regulatory interactions between the TFs and the genes were retained and the regulatory signals were deduced. Theoretical studies demonstrated that the regulatory signals were accurately reconstructed even in the case where only three independent transcriptome datasets were available. At least 80% of the main target genes were correctly predicted in the extreme condition of high noise level and small number of datasets. Our algorithm was tested with transcriptome data taken from mice under rapamycin treatment. The initial network topology from the literature contains 70 TFs, 778 genes, and 1423 edges between the TFs and genes. Our method retained 1074 edges (i.e. 75% of the original edge number and identified 17 TFs as being significantly perturbed under the experimental condition. Twelve of these TFs are involved in MAPK signaling or myeloid leukemia pathways defined in the KEGG database, or are known to physically interact with each other. Additionally, four of these TFs, which are Hif1a, Cebpb, Nfkb1, and Atf1, are known targets of rapamycin. Furthermore, the trimmed network was able to predict Eno1 as an important target of Hif1a; this key interaction could not be detected without trimming the regulatory network. Conclusions The advantage of our new algorithm

  19. Potential role of TRIM3 as a novel tumour suppressor in colorectal cancer (CRC) development.

    Science.gov (United States)

    Piao, Mei-Yu; Cao, Hai-Long; He, Na-Na; Xu, Meng-Que; Dong, Wen-Xiao; Wang, Wei-Qiang; Wang, Bang-Mao; Zhou, Bing

    2016-01-01

    Colorectal cancer (CRC) is the third leading cause of cancer-related mortality in the United States. Recent cancer genome-sequencing efforts and complementary functional studies have led to the identification of a collection of candidate 'driver' genes involved in CRC tumorigenesis. Tripartite motif (TRIM3) is recently identified as a tumour suppressor in glioblastoma but this tumour-suppressive function has not been investigated in CRC. In this study, we investigated the potential role of TRIM3 as a tumour suppressor in CRC development by manipulating the expression of TRIM3 in two authentic CRC cell lines, HCT116 and DLD1, followed by various functional assays, including cell proliferation, colony formation, scratch wound healing, soft agar, and invasion assays. Xenograft experiment was performed to examine in vivo tumour-suppressive properties of TRIM3. Small-interfering RNA (siRNA) mediated knockdown of TRIM3 conferred growth advantage in CRC cells. In contrast, overexpression of TRIM3 affected cell survival, cell migration, anchorage independent growth and invasive potential in CRC cells. In addition, TRIM3 was found to be down-regulated in human colon cancer tissues compared with matched normal colon tissues. Overexpression of TRIM3 significantly inhibited tumour growth in vivo using xenograft mouse models. Mechanistic investigation revealed that TRIM3 can regulate p53 protein level through its stabilisation. TRIM3 functions as a tumour suppressor in CRC progression. This tumour-suppressive function is exerted partially through regulation of p53 protein. Therefore, this protein may represent a novel therapeutic target for prevention or intervention of CRC.

  20. Safety and reliability of pressure components with special emphasis on the contribution of component and large specimen testing to structural integrity assessment methodology. Vol. 1 and 2

    International Nuclear Information System (INIS)

    1987-01-01

    The 51 papers of the 13. MPA-seminar contribute to structural integrity assessment methodology with special emphasis on the component and large specimen testing. 8 of the papers deal with fracture mechanics, 6 papers with dynamic loading, 13 papers with nondestructive testing, 2 papers with radiation embrittlement, 5 papers with pipe failure, 4 papers with components, 2 papers with thermal shock loading, 5 papers with the high temperature behaviour, 4 papers with the integrity of vessels and 3 papers with the integrity of welded joints. Especially also the fracture behaviour of steel material is verificated. All papers are separately indexed and analysed for the database. (DG) [de

  1. 77 FR 67399 - Trim Systems Operating Corp., a Subsidiary of Commercial Vehicle Group, Inc., Including On-Site...

    Science.gov (United States)

    2012-11-09

    ... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-81,393] Trim Systems Operating..., applicable to workers and former workers of Trim Systems Operating Corp., a subsidiary of Commercial Vehicle.... The amended notice applicable to TA-W-81,393 is hereby issued as follows: All workers of Trim Systems...

  2. Efficient running of steam generator trims fuel cost

    International Nuclear Information System (INIS)

    Selim, M.; Eltouny, S.A.

    1993-01-01

    E scaling energy prices have led to drastic changes in the operating philosophy of the worldwide industry. About 50% of the thermal energy in industry is being consumed in steam boilers. The new energy reduction programs that have been adopted in egypt draw attention to the boilers, not only to trim energy consumption and improve the production of steam but also to save as much money as possible in doing it. Organization for energy planning (OEP) has started a program for 'Boiler efficiency improvement' in industry since 2 years. The program aimed at performing energy audits in a selective number of industries in both public and private sectors using fire tube boilers produced locally by El Nasr company. As a result of audits an evaluation of performance of this type of boilers was,performed. The energy profiles and the common problems affecting the efficiency of boilers were determined. Energy conservation opportunities (ECO) were identified. 9 figs

  3. Epoxy resin casting of trim coils for superconducting cyclotron

    International Nuclear Information System (INIS)

    Hajra, D.P.; Sarkar, S.C.; Saha, Subimal; Chaudhuri, J.; Bhandari, R.K.

    2006-01-01

    The life of any magnet depends on the soundness of the coil insulation, its aging properties and initial and final endurance limitations. The insulation of water-cooled trim coils for superconducting cyclotron is made of glass fibre tape with heat cured unfilled epoxy resin combination. This type of insulation has been selected to achieve excellent stability against thermal and electromagnetic stresses, tight dimensional control, good dielectric strength, non-hygroscopic and considerably low vapour-pressure as it will be inside rough vacuum. The process development and the difficulties encountered for appropriate selection of epoxy resin combination, potting, vacuum process, curing cycle, control of coil dimension to achieve a sound coil absolutely free from cracks, trapped air and voids has been discussed. (author)

  4. High resolution micro ultrasonic machining for trimming 3D microstructures

    International Nuclear Information System (INIS)

    Viswanath, Anupam; Li, Tao; Gianchandani, Yogesh

    2014-01-01

    This paper reports on the evaluation of a high resolution micro ultrasonic machining (HR-µUSM) process suitable for post fabrication trimming of complex 3D microstructures made from fused silica. Unlike conventional USM, the HR-µUSM process aims for low machining rates, providing high resolution and high surface quality. The machining rate is reduced by keeping the micro-tool tip at a fixed distance from the workpiece and vibrating it at a small amplitude. The surface roughness is improved by an appropriate selection of abrasive particles. Fluidic modeling is performed to study interaction among the vibrating micro-tool tip, workpiece, and the slurry. Using 304 stainless steel (SS304) tool tips of 50 µm diameter, the machining performance of the HR-µUSM process is characterized on flat fused silica substrates. The depths and surface finish of machined features are evaluated as functions of slurry concentrations, separation between the micro-tool and workpiece, and machining time. Under the selected conditions, the HR-µUSM process achieves machining rates as low as 10 nm s −1  averaged over the first minute of machining of a flat virgin sample. This corresponds to a mass removal rate of ≈20 ng min −1 . The average surface roughness, S a , achieved is as low as 30 nm. Analytical and numerical modeling are used to explain the typical profile of the machined features as well as machining rates. The process is used to demonstrate trimming of hemispherical 3D shells made of fused silica. (paper)

  5. Identification of TRIM27 as a novel degradation target of herpes simplex virus 1 ICP0.

    Science.gov (United States)

    Conwell, Sara E; White, Anne E; Harper, J Wade; Knipe, David M

    2015-01-01

    The herpes simplex virus 1 (HSV-1) immediate early protein ICP0 performs many functions during infection, including transactivation of viral gene expression, suppression of innate immune responses, and modification and eviction of histones from viral chromatin. Although these functions of ICP0 have been characterized, the detailed mechanisms underlying ICP0's complex role during infection warrant further investigation. We thus undertook an unbiased proteomic approach to identifying viral and cellular proteins that interact with ICP0 in the infected cell. Cellular candidates resulting from our analysis included the ubiquitin-specific protease USP7, the transcriptional repressor TRIM27, DNA repair proteins NBN and MRE11A, regulators of apoptosis, including BIRC6, and the proteasome. We also identified two HSV-1 early proteins involved in nucleotide metabolism, UL39 and UL50, as novel candidate interactors of ICP0. Because TRIM27 was the most statistically significant cellular candidate, we investigated the relationship between TRIM27 and ICP0. We observed rapid, ICP0-dependent loss of TRIM27 during HSV-1 infection. TRIM27 protein levels were restored by disrupting the RING domain of ICP0 or by inhibiting the proteasome, arguing that TRIM27 is a novel degradation target of ICP0. A mutant ICP0 lacking E3 ligase activity interacted with endogenous TRIM27 during infection as demonstrated by reciprocal coimmunoprecipitation and supported by immunofluorescence data. Surprisingly, ICP0-null mutant virus yields decreased upon TRIM27 depletion, arguing that TRIM27 has a positive effect on infection despite being targeted for degradation. These results illustrate a complex interaction between TRIM27 and viral infection with potential positive or negative effects of TRIM27 on HSV under different infection conditions. During productive infection, a virus must simultaneously redirect multiple cellular pathways to replicate itself while evading detection by the host's defenses. To

  6. General Model for Retroviral Capsid Pattern Recognition by TRIM5 Proteins.

    Science.gov (United States)

    Wagner, Jonathan M; Christensen, Devin E; Bhattacharya, Akash; Dawidziak, Daria M; Roganowicz, Marcin D; Wan, Yueping; Pumroy, Ruth A; Demeler, Borries; Ivanov, Dmitri N; Ganser-Pornillos, Barbie K; Sundquist, Wesley I; Pornillos, Owen

    2018-02-15

    Restriction factors are intrinsic cellular defense proteins that have evolved to block microbial infections. Retroviruses such as HIV-1 are restricted by TRIM5 proteins, which recognize the viral capsid shell that surrounds, organizes, and protects the viral genome. TRIM5α uses a SPRY domain to bind capsids with low intrinsic affinity ( K D of >1 mM) and therefore requires higher-order assembly into a hexagonal lattice to generate sufficient avidity for productive capsid recognition. TRIMCyp, on the other hand, binds HIV-1 capsids through a cyclophilin A domain, which has a well-defined binding site and higher affinity ( K D of ∼10 μM) for isolated capsid subunits. Therefore, it has been argued that TRIMCyp proteins have dispensed with the need for higher-order assembly to function as antiviral factors. Here, we show that, consistent with its high degree of sequence similarity with TRIM5α, the TRIMCyp B-box 2 domain shares the same ability to self-associate and facilitate assembly of a TRIMCyp hexagonal lattice that can wrap about the HIV-1 capsid. We also show that under stringent experimental conditions, TRIMCyp-mediated restriction of HIV-1 is indeed dependent on higher-order assembly. Both forms of TRIM5 therefore use the same mechanism of avidity-driven capsid pattern recognition. IMPORTANCE Rhesus macaques and owl monkeys are highly resistant to HIV-1 infection due to the activity of TRIM5 restriction factors. The rhesus macaque TRIM5α protein blocks HIV-1 through a mechanism that requires self-assembly of a hexagonal TRIM5α lattice around the invading viral core. Lattice assembly amplifies very weak interactions between the TRIM5α SPRY domain and the HIV-1 capsid. Assembly also promotes dimerization of the TRIM5α RING E3 ligase domain, resulting in synthesis of polyubiquitin chains that mediate downstream steps of restriction. In contrast to rhesus TRIM5α, the owl monkey TRIM5 homolog, TRIMCyp, binds isolated HIV-1 CA subunits much more tightly

  7. Genetic evaluation of claw health traits accounting for potential preselection of cows to be trimmed.

    Science.gov (United States)

    Croué, Iola; Fikse, Freddy; Johansson, Kjell; Carlén, Emma; Thomas, Gilles; Leclerc, Hélène; Ducrocq, Vincent

    2017-10-01

    Claw lesions are one of the most important health issues in dairy cattle. Although the frequency of claw lesions depends greatly on herd management, the frequency can be lowered through genetic selection. A genetic evaluation could be developed based on trimming records collected by claw trimmers; however, not all cows present in a herd are usually selected by the breeder to be trimmed. The objectives of this study were to investigate the importance of the preselection of cows for trimming, to account for this preselection, and to estimate genetic parameters of claw health traits. The final data set contained 25,511 trimming records of French Holstein cows. Analyzed claw lesion traits were digital dermatitis, heel horn erosion, interdigital hyperplasia, sole hemorrhage circumscribed, sole hemorrhage diffused, sole ulcer, and white line fissure. All traits were analyzed as binary traits in a multitrait linear animal model. Three scenarios were considered: including only trimmed cows in a 7-trait model (scenario 1); or trimmed cows and contemporary cows not trimmed but present at the time of a visit (considering that nontrimmed cows were healthy) in a 7-trait model (scenario 2); or trimmed cows and contemporary cows not trimmed but present at the time of a visit (considering lesion records for trimmed cows only), in an 8-trait model, including a 0/1 trimming status trait (scenario 3). For scenario 3, heritability estimates ranged from 0.02 to 0.09 on the observed scale. Genetic correlations clearly revealed 2 groups of traits (digital dermatitis, heel horn erosion, and interdigital hyperplasia on the one hand, and sole hemorrhage circumscribed, sole hemorrhage diffused, sole ulcer, and white line fissure on the other hand). Heritabilities on the underlying scale did not vary much depending on the scenario: the effect of the preselection of cows for trimming on the estimation of heritabilities appeared to be negligible. However, including untrimmed cows as healthy

  8. Testing multistage gain and offset trimming in a single photon counting IC with a charge sharing elimination algorithm

    International Nuclear Information System (INIS)

    Krzyżanowska, A.; Gryboś, P.; Szczygieł, R.; Maj, P.

    2015-01-01

    Designing a hybrid pixel detector readout electronics operating in a single photon counting mode is a very challenging process, where many main parameters are optimized in parallel (e.g. gain, noise, and threshold dispersion). Additional requirements for a smaller pixel size with extended functionality push designers to use new deep sub-micron technologies. Minimizing the channel size is possible, however, with a decreased pixel size, the charge sharing effect becomes a more important issue. To overcome this problem, we designed an integrated circuit prototype produced in CMOS 40 nm technology, which has an extended functionality of a single pixel. A C8P1 algorithm for the charge sharing effect compensation was implemented. In the algorithm's first stage the charge is rebuilt in a signal rebuilt hub fed by the CSA (charge sensitive amplifier) outputs from four neighbouring pixels. Then, the pixel with the biggest amount of charge is chosen, after a comparison with all the adjacent ones. In order to process the data in such a complicated way, a certain architecture of a single channel was proposed, which allows for: ⋅ processing the signal with the possibility of total charge reconstruction (by connecting with the adjacent pixels), ⋅ a comparison of certain pixel amplitude to its 8 neighbours, ⋅ the extended testability of each block inside the channel to measure CSA gain dispersion, shaper gain dispersion, threshold dispersion (including the simultaneous generation of different pulse amplitudes from different pixels), ⋅ trimming all the necessary blocks for proper operation. We present a solution for multistage gain and offset trimming implemented in the IC prototype. It allows for minimization of the total charge extraction errors, minimization of threshold dispersion in the pixel matrix and minimization of errors of comparison of certain pixel pulse amplitudes with all its neighbours. The detailed architecture of a single channel is presented

  9. Cyclophilin A potentiates TRIM5α inhibition of HIV-1 nuclear import without promoting TRIM5α binding to the viral capsid.

    Directory of Open Access Journals (Sweden)

    Mallori Burse

    Full Text Available The host immunophilin cyclophilin A (CypA binds to the capsid protein (CA of HIV-1 and regulates its infectivity. Depending on the target cell type, CypA can either promote or inhibit HIV-1 infection. The ability of CypA to promote HIV-1 infection has been extensively studied and linked to several steps in early replication including uncoating, reverse transcription and nuclear import. By contrast, the mechanism by which CypA inhibits infection is less well understood. We investigated the mechanism by which CypA potentiates restriction of HIV-1 by the tripartite motif-containing protein 5 (TRIM5α. Depletion of TRIM5α in the African green monkey cell line Vero, resulted in a loss of inhibition of infection by CypA, demonstrating that inhibition by CypA is mediated by TRIM5α. Complementary genetic and biochemical assays failed to demonstrate an ability of CypA to promote binding of TRIM5α to the viral capsid. TRIM5α inhibits HIV-1 reverse transcription in a proteasome-dependent manner; however, we observed that inhibition of proteasome activity did not reduce the ability of CypA to inhibit infection, suggesting that CypA acts at a step after reverse transcription. Accordingly, we observed a CypA-dependent reduction in the accumulation of nuclear HIV-1 DNA, indicating that CypA specifically promotes TRIM5α inhibition of HIV-1 nuclear import. We also observed that the ability of CypA to inhibit HIV-1 infection is abolished by amino acid substitutions within the conserved CPSF6-binding surface in CA. Our results indicate that CypA inhibits HIV-1 infection in Vero cells not by promoting TRIM5α binding to the capsid but by blocking nuclear import of the HIV-1 preintegration complex.

  10. Effects of high voltage pulse trimming on structural properties of thick-film resistors

    Directory of Open Access Journals (Sweden)

    Stanimirović Zdravko

    2017-01-01

    Full Text Available Nowadays, compact and reliable electronic devices including up-to-date ceramic micro-electro-mechanical systems require thick-film resistors with significantly reduced dimensions and stable and precise resistance values. For that reason, instead of standard laser trimming method, high voltage pulse trimming of thick-film resistors is being introduced. This method allows controlled and reliable resistance adjustment regardless of resistor position or dimensions and without the presence of cuts. However, it causes irreversible structural changes in the pseudorandom network formed during sintering causing the changes in conducting mechanisms. In this paper results of the experimental investigation of high voltage pulse trimming of thick-film resistors are presented. Obtained results are analyzed and correlations between resistance and low-frequency noise changes and changes in conducting mechanisms in resistors due to high voltage pulse trimming are observed. Sources of measured fluctuations are identified and it is shown that this type of trimming is a valid alternative trimming method to the dominant laser trimming. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. III44003 and III45007

  11. TRIM32 ubiquitin E3 ligase, one enzyme for several pathologies: From muscular dystrophy to tumours.

    Science.gov (United States)

    Lazzari, Elisa; Meroni, Germana

    2016-10-01

    TRIM32 is a member of the TRIpartite Motif family characterised by the presence of an N-terminal three-domain-module that includes a RING domain, which confers E3 ubiquitin ligase activity, one or two B-box domains and a Coiled-Coil region that mediates oligomerisation. Several TRIM32 substrates were identified including muscular proteins and proteins involved in cell cycle regulation and cell motility. As ubiquitination is a versatile post-translational modification that can affect target turnover, sub-cellular localisation or activity, it is likely that diverse substrates may be differentially affected by TRIM32-mediated ubiquitination, reflecting its multi-faceted roles in muscle physiology, cancer and immunity. With particular relevance for muscle physiology, mutations in TRIM32 are associated with autosomal recessive Limb-Girdle Muscular Dystrophy 2H, a muscle-wasting disease with variable clinical spectrum ranging from almost asymptomatic to wheelchair-bound patients. In this review, we will focus on the ability of TRIM32 to mark specific substrates for proteasomal degradation discussing how the TRIM32-proteasome axis may (i) be important for muscle homeostasis and for the pathogenesis of muscular dystrophy; and (ii) define either an oncogenic or tumour suppressive role for TRIM32 in the context of different types of cancer. Copyright © 2016 Elsevier Ltd. All rights reserved.

  12. The effect of Trim5 polymorphisms on the clinical course of HIV-1 infection.

    Directory of Open Access Journals (Sweden)

    Daniëlle van Manen

    2008-02-01

    Full Text Available The antiviral factor tripartite interaction motif 5alpha (Trim5alpha restricts a broad range of retroviruses in a species-specific manner. Although human Trim5alpha is unable to block HIV-1 infection in human cells, a modest inhibition of HIV-1 replication has been reported. Recently two polymorphisms in the Trim5 gene (H43Y and R136Q were shown to affect the antiviral activity of Trim5alpha in vitro. In this study, participants of the Amsterdam Cohort studies were screened for polymorphisms at amino acid residue 43 and 136 of the Trim5 gene, and the potential effects of these polymorphisms on the clinical course of HIV-1 infection were analyzed. In agreement with the reported decreased antiviral activity of Trim5alpha that contains a Y at amino acid residue 43 in vitro, an accelerated disease progression was observed for individuals who were homozygous for the 43Y genotype as compared to individuals who were heterozygous or homozygous for the 43H genotype. A protective effect of the 136Q genotype was observed but only after the emergence of CXCR4-using (X4 HIV-1 variants and when a viral load of 10(4.5 copies per ml plasma was used as an endpoint in survival analysis. Interestingly, naive CD4 T cells, which are selectively targeted by X4 HIV-1, revealed a significantly higher expression of Trim5alpha than memory CD4 T cells. In addition, we observed that the 136Q allele in combination with the -2GG genotype in the 5'UTR was associated with an accelerated disease progression. Thus, polymorphisms in the Trim5 gene may influence the clinical course of HIV-1 infection also underscoring the antiviral effect of Trim5alpha on HIV-1 in vivo.

  13. The Effect of Trim5 Polymorphisms on the Clinical Course of HIV-1 Infection

    Science.gov (United States)

    van Manen, Daniëlle; Rits, Maarten A. N; Beugeling, Corrine; van Dort, Karel; Schuitemaker, Hanneke; Kootstra, Neeltje A

    2008-01-01

    The antiviral factor tripartite interaction motif 5α (Trim5α) restricts a broad range of retroviruses in a species-specific manner. Although human Trim5α is unable to block HIV-1 infection in human cells, a modest inhibition of HIV-1 replication has been reported. Recently two polymorphisms in the Trim5 gene (H43Y and R136Q) were shown to affect the antiviral activity of Trim5α in vitro. In this study, participants of the Amsterdam Cohort studies were screened for polymorphisms at amino acid residue 43 and 136 of the Trim5 gene, and the potential effects of these polymorphisms on the clinical course of HIV-1 infection were analyzed. In agreement with the reported decreased antiviral activity of Trim5α that contains a Y at amino acid residue 43 in vitro, an accelerated disease progression was observed for individuals who were homozygous for the 43Y genotype as compared to individuals who were heterozygous or homozygous for the 43H genotype. A protective effect of the 136Q genotype was observed but only after the emergence of CXCR4-using (X4) HIV-1 variants and when a viral load of 104.5 copies per ml plasma was used as an endpoint in survival analysis. Interestingly, naive CD4 T cells, which are selectively targeted by X4 HIV-1, revealed a significantly higher expression of Trim5α than memory CD4 T cells. In addition, we observed that the 136Q allele in combination with the −2GG genotype in the 5′UTR was associated with an accelerated disease progression. Thus, polymorphisms in the Trim5 gene may influence the clinical course of HIV-1 infection also underscoring the antiviral effect of Trim5α on HIV-1 in vivo. PMID:18248091

  14. Characterization and biological function analysis of the TRIM47 gene from common carp (Cyprinus carpio).

    Science.gov (United States)

    Wang, Yeda; Kuang, Ming; Lu, Yuanan; Lin, Li; Liu, Xueqin

    2017-09-05

    The TRIM family protein was known to play an important role in many cellular processes, including potential antiviral activity, which has attracted lots of attention. In this study, a TRIM47 homolog from common carp (Cyprinus carpio) was cloned and the full length coding DNA sequence (CDS) of this gene was analyzed, results showed that there was a 97% similarity between common carp and zebrafish (Danio rerio), but only 18% similarity with that of human (Homo sapiens) and mouse (Mus musculus). The tissue distribution analysis showed TRIM47 had the highest mRNA level in the brain, a few immune related organs such as liver and kidney also had a relatively high level of TRIM47 expression. SVCV infection decreased TRIM47 mRNA level significantly both in vitro and in vivo, but its expression was not affected by the virus at the protein level. The recombinant plasmid pcDNA4-TRIM47-His was constructed, the subcellular localization in FHM cells showed that TRIM47 uniformly distributed in the cytoplasm at the form of tiny spots, and partially localized in the mitochondria. Overexpression TRIM47 in FHM cells significantly decreased the mRNA level of SVCV-G gene, and it was accompanied with the increasing of IFN1, a member of type I IFN, at the case of SVCV stimulation. In summary, our results had first demonstrated that TRIM47 of the common carp played an important role in viral resistance processes as well as the regulation of IFN signaling pathway. Copyright © 2017. Published by Elsevier B.V.

  15. Development of the SSC [Superconducting Super Collider] trim coil beam tube assembly

    International Nuclear Information System (INIS)

    Skaritka, J.; Kelly, E.; Schneider, W.

    1987-01-01

    The Superconducting Super Collider uses ≅9600 dipole magnets. The magnets have been carefully designed to exhibit minimal magnetic field harmonics. However, because of superconductor magnetization effects, iron saturation and conductor/coil positioning errors, certain harmonic errors are possible and must be corrected by use of multipole correctors called trim coils. For the most efficient use of axial space in the magnet, and lowest possible current, a distributed internal correction coil design is planned. The trim coil assembly is secured to the beam tube, a uhv tube with special strength, size, conductivity and vacuum. The report details the SSC trim coil/beam tube assembly specifications, history, and ongoing development

  16. A Unified Methodology for Aerospace Systems Integration Based on Entropy and the Second Law of Thermodynamics: Aerodynamics Assessment

    National Research Council Canada - National Science Library

    Camberos, Jose A; Nomura, Shohei; Stewart, Jason; Figliola, Richard

    2004-01-01

    .... The objective of this project is to relate work-potential losses (exergy destruction) to the aerodynamics forces in an attempt to validate a new design methodology based on the second law of thermodynamic...

  17. An integrated quality function deployment and capital budgeting methodology for occupational safety and health as a systems thinking approach: the case of the construction industry.

    Science.gov (United States)

    Bas, Esra

    2014-07-01

    In this paper, an integrated methodology for Quality Function Deployment (QFD) and a 0-1 knapsack model is proposed for occupational safety and health as a systems thinking approach. The House of Quality (HoQ) in QFD methodology is a systematic tool to consider the inter-relationships between two factors. In this paper, three HoQs are used to consider the interrelationships between tasks and hazards, hazards and events, and events and preventive/protective measures. The final priority weights of events are defined by considering their project-specific preliminary weights, probability of occurrence, and effects on the victim and the company. The priority weights of the preventive/protective measures obtained in the last HoQ are fed into a 0-1 knapsack model for the investment decision. Then, the selected preventive/protective measures can be adapted to the task design. The proposed step-by-step methodology can be applied to any stage of a project to design the workplace for occupational safety and health, and continuous improvement for safety is endorsed by the closed loop characteristic of the integrated methodology. Copyright © 2013 Elsevier Ltd. All rights reserved.

  18. Life-cycle energy optimisation : A proposed methodology for integrating environmental considerations early in the vehicle engineering design process

    OpenAIRE

    O'Reilly, Ciarán J.; Göransson, Peter; Funazaki, Atsushi; Suzuki, Tetsuya; Edlund, Stefan; Gunnarsson, Cecilia; Lundow, Jan-Olov; Cerin, Pontus; Cameron, Christopher J.; Wennhage, Per; Potting, José

    2016-01-01

    To enable the consideration of life cycle environmental impacts in the early stages of vehicle design, a methodology using the proxy of life cycle energy is proposed in this paper. The trade-offs in energy between vehicle production, operational performance and end-of-life are formulated as a mathematical problem, and simultaneously balanced with other transport-related functionalities, and may be optimised. The methodology is illustrated through an example design study, which is deliberately...

  19. Methodological exemplar of integrating quantitative and qualitative evidence - supportive care for men with prostate cancer:what are the most important components?

    OpenAIRE

    Huntley, Alyson; King, Anna J L; Moore, Theresa H M; Paterson, Charlotte; Persad, Raj; Sharp, Debbie J; Evans, Maggie A

    2017-01-01

    AIMS: To present a methodological exemplar of integrating findings from a quantitative and qualitative review on the same topic to provide insight into components of care that contribute to supportive care that is acceptable to men with prostate cancer.BACKGROUND: Men with prostate cancer are likely to live a long time with the disease, experience side effects from treatment and therefore have ongoing supportive care needs. Quantitative and qualitative reviews have been published but the find...

  20. Reducing hospital-acquired pressure ulcers using bundle methodology in pediatric and neonatal patients receiving extracorporeal membrane oxygenation therapy: An integrative review and call to action.

    Science.gov (United States)

    Courtwright, Suzanne E; Mastro, Kari A; Preuster, Christa; Dardashti, Navid; McGill, Sandra; Madelon, Myrlene; Johnson, Donna

    2017-10-01

    This review focuses on identifying (1) evidence of the effectiveness of care bundle methodology to reduce hospital-acquired pressure ulcers (HAPUs) in pediatric and neonatal patients receiving extracorporeal membrane oxygenation (ECMO) therapy and (2) barriers to implementing HAPU care bundles in this at-risk population. An integrative review was conducted and reported following the Preferred Reporting Items for Systematic Reviews and Meta-Analyses guidelines. A search of the scientific literature was performed. Studies included were published between January 2011 and February 2016. A total of seven articles met inclusion criteria. Data were extracted from each published article and analyzed to identify common themes, specifically bundle methodology and barriers to implementing HAPU bundles, in this population. There is limited research on effectiveness of care bundle methodology in reducing HAPUs in children, and no research specific to its effectiveness in pediatric or neonatal ECMO patients. No research was identified studying barriers to implementation of HAPU care bundles in this population. Nurses are well poised to test innovative strategies to prevent HAPUs. Nurses should consider implementing and testing bundle methodology to reduce HAPU in this at-risk population, and conduct research to identify any barriers to implementing this strategy. There is literature to support the use of nurses as unit-based skin care champions to facilitate teamwork and reliable use of the bundle, both critical components to the success of bundle methodology. © 2017 Wiley Periodicals, Inc.

  1. International Comprehensive Ocean-Atmosphere Data Set (ICOADS) with Enhanced Trimming, Release 3

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains the latest official release of International Comprehensive Ocean-Atmosphere Data Set (ICOADS) with Enhanced Trimming, provided in a common...

  2. Synchronization Of TRIMs Principles In The Legislation Of Mining Sector In Indonesia

    Directory of Open Access Journals (Sweden)

    Agus Lanini

    2015-08-01

    Full Text Available The aims of this research are to know and explain synchronizing the principles of TRIMs at the foreign direct investment FDI and mining regulation in Indonesia. The research using normative research that conducted through library or document study such legal resources as primary sources secondary and tertiary sources that will be studied with applied legal approach comparative history and conceptual approach. Research results are revealing that synchronizing between the principles of TRIMs and Investment act 2007and Mineral and Coal act 2009 were not harmonized. It should be TRIMs and investment act 2007 have some similarity principles as harmonized even though Mineral and Coal act 2009 does not enough accessibility for the principles of TRIMs. Implication of the Mineral and Coal act 2009 raise a strong and real authority of the state even central or local government. Those policy results an overlap regulation caused state management system over natural resources ineffective.

  3. Novel trimming technique for tunable HTS microstrip filters

    Energy Technology Data Exchange (ETDEWEB)

    Sekiya, N. [Department of Electrical Engineering, Yamanashi University, Nakagawa-Sekiya Laboratory, 4-3-11 Takeda, Kofu 400-8511 (Japan)], E-mail: nsekiya@yamanashi.ac.jp; Nakagawa, Y. [Department of Electrical Engineering, Yamanashi University, Nakagawa-Sekiya Laboratory, 4-3-11 Takeda, Kofu 400-8511 (Japan); Saito, A.; Ohshima, S. [Yamagata University, 4-3-16 Johnan, Yonezawa 992-8510 (Japan)

    2008-09-15

    We have developed a method using additional electric pads for trimming tunable high-temperature superconducting (HTS) microstrip filters. These filters are generally tuned by adjusting the gap between a dielectric floating plate above the filter. When the floating plate approached the filter, the center frequency was shifted to a lower frequency. However, the insertion loss increases due to variation in the external quality factors varying from the design parameter. The external quality factors are usually controlled by adjusting the length of the input/output (I/O) coupled-line elements and the gap between the elements and the resonator. In our method, additional electric pads are distributed at the open-end of the I/O coupled-line elements of a 3-pole hairpin bandpass filter to enable adjustment of the external quality factors so as to reduce insertion loss. The electric pads consist of line-and-space patterns. They are eclectically connected to the coupled-line elements to adjust the line length and gap width and thereby control the external quality factors. An electromagnetic simulator was used for the design and analysis. The simulation results showed that the additional electric pads are effective in improving the insertion loss of the HTS bandpass filter after tuning.

  4. Novel trimming technique for tunable HTS microstrip filters

    International Nuclear Information System (INIS)

    Sekiya, N.; Nakagawa, Y.; Saito, A.; Ohshima, S.

    2008-01-01

    We have developed a method using additional electric pads for trimming tunable high-temperature superconducting (HTS) microstrip filters. These filters are generally tuned by adjusting the gap between a dielectric floating plate above the filter. When the floating plate approached the filter, the center frequency was shifted to a lower frequency. However, the insertion loss increases due to variation in the external quality factors varying from the design parameter. The external quality factors are usually controlled by adjusting the length of the input/output (I/O) coupled-line elements and the gap between the elements and the resonator. In our method, additional electric pads are distributed at the open-end of the I/O coupled-line elements of a 3-pole hairpin bandpass filter to enable adjustment of the external quality factors so as to reduce insertion loss. The electric pads consist of line-and-space patterns. They are eclectically connected to the coupled-line elements to adjust the line length and gap width and thereby control the external quality factors. An electromagnetic simulator was used for the design and analysis. The simulation results showed that the additional electric pads are effective in improving the insertion loss of the HTS bandpass filter after tuning

  5. Modeling of trim panels in the energy finite element analysis

    Science.gov (United States)

    Moravaeji, Seyed-Javid

    Modeling a trim panel is divided into finding the power exchange through two different paths: (i) the connection of the outer and inner panels (ii) through the layers directly. The vibrational power exchanged through the mounts is modeled as the connection of two parallel plates connected via a beam. Wave matrices representing plates and beams are derived separately; then a matrix method is proposed to solve for the wave amplitudes and hence the vibrational power exchange between the plates accordingly. A closed form formula for the case of connection of two identical plates is derived. For the power transmission loss directly through the layers, first transfer matrices representing layers made of different materials is considered. New matrices for a porous layer are derived. A method of finding the layered structure transfer matrix is proposed. It is concluded that in general a single isotropic layer cannot replace a structure accurately. Finally, on the basis of an equivalent transfer matrix, an optimization process for is proposed to replace the panel by a suitable set of layers.

  6. MATLAB Stability and Control Toolbox Trim and Static Stability Module

    Science.gov (United States)

    Kenny, Sean P.; Crespo, Luis

    2012-01-01

    MATLAB Stability and Control Toolbox (MASCOT) utilizes geometric, aerodynamic, and inertial inputs to calculate air vehicle stability in a variety of critical flight conditions. The code is based on fundamental, non-linear equations of motion and is able to translate results into a qualitative, graphical scale useful to the non-expert. MASCOT was created to provide the conceptual aircraft designer accurate predictions of air vehicle stability and control characteristics. The code takes as input mass property data in the form of an inertia tensor, aerodynamic loading data, and propulsion (i.e. thrust) loading data. Using fundamental nonlinear equations of motion, MASCOT then calculates vehicle trim and static stability data for the desired flight condition(s). Available flight conditions include six horizontal and six landing rotation conditions with varying options for engine out, crosswind, and sideslip, plus three take-off rotation conditions. Results are displayed through a unique graphical interface developed to provide the non-stability and control expert conceptual design engineer a qualitative scale indicating whether the vehicle has acceptable, marginal, or unacceptable static stability characteristics. If desired, the user can also examine the detailed, quantitative results.

  7. On the optimal trimming of high-throughput mRNA sequence data

    Directory of Open Access Journals (Sweden)

    Matthew D MacManes

    2014-01-01

    Full Text Available The widespread and rapid adoption of high-throughput sequencing technologies has afforded researchers the opportunity to gain a deep understanding of genome level processes that underlie evolutionary change, and perhaps more importantly, the links between genotype and phenotype. In particular, researchers interested in functional biology and adaptation have used these technologies to sequence mRNA transcriptomes of specific tissues, which in turn are often compared to other tissues, or other individuals with different phenotypes. While these techniques are extremely powerful, careful attention to data quality is required. In particular, because high-throughput sequencing is more error-prone than traditional Sanger sequencing, quality trimming of sequence reads should be an important step in all data processing pipelines. While several software packages for quality trimming exist, no general guidelines for the specifics of trimming have been developed. Here, using empirically derived sequence data, I provide general recommendations regarding the optimal strength of trimming, specifically in mRNA-Seq studies. Although very aggressive quality trimming is common, this study suggests that a more gentle trimming, specifically of those nucleotides whose Phred score < 2 or < 5, is optimal for most studies across a wide variety of metrics.

  8. Neuroanatomy-based matrix-guided trimming protocol for the rat brain.

    Science.gov (United States)

    Defazio, Rossella; Criado, Ana; Zantedeschi, Valentina; Scanziani, Eugenio

    2015-02-01

    Brain trimming through defined neuroanatomical landmarks is recommended to obtain consistent sections in rat toxicity studies. In this article, we describe a matrix-guided trimming protocol that uses channels to reproduce coronal levels of anatomical landmarks. Both setup phase and validation study were performed on Han Wistar male rats (Crl:WI(Han)), 10-week-old, with bodyweight of 298 ± 29 (SD) g, using a matrix (ASI-Instruments(®), Houston, TX) fitted for brains of rats with 200 to 400 g bodyweight. In the setup phase, we identified eight channels, that is, 6, 8, 10, 12, 14, 16, 19, and 21, matching the recommended landmarks midway to the optic chiasm, frontal pole, optic chiasm, infundibulum, mamillary bodies, midbrain, middle cerebellum, and posterior cerebellum, respectively. In the validation study, we trimmed the immersion-fixed brains of 60 rats using the selected channels to determine how consistently the channels reproduced anatomical landmarks. Percentage of success (i.e., presence of expected targets for each level) ranged from 89 to 100%. Where 100% success was not achieved, it was noted that the shift in brain trimming was toward the caudal pole. In conclusion, we developed and validated a trimming protocol for the rat brain that allow comparable extensiveness, homology, and relevance of coronal sections as the landmark-guided trimming with the advantage of being quickly learned by technicians. © 2014 by The Author(s).

  9. Multi-attribute Evaluation of Website Quality in E-business Using an Integrated Fuzzy AHPTOPSIS Methodology

    Directory of Open Access Journals (Sweden)

    Tolga Kaya

    2010-09-01

    Full Text Available Success of an e-business company is strongly associated with the relative quality of its website compared to that of its competitors. The purpose of this study is to propose a multi-attribute e-business website quality evaluation methodology based on a modified fuzzy TOPSIS approach. In the proposed methodology, weights of the evaluation criteria are generated by a fuzzy AHP procedure. In performance evaluation problems, the judgments of the experts may usually be vague in form. As fuzzy logic can successfully deal with this kind of uncertainty in human preferences, both classical TOPSIS and classical AHP procedures are implemented under fuzzy environment. The proposed TOPSIS-AHP methodology has successfully been applied to a multi-attribute website quality evaluation problem in Turkish e-business market. Nine sub-criteria under four main categories are used in the evaluation of the most popular e-business websites of Turkey. A sensitivity analysis is also provided.

  10. Shrinkage covariance matrix approach based on robust trimmed mean in gene sets detection

    Science.gov (United States)

    Karjanto, Suryaefiza; Ramli, Norazan Mohamed; Ghani, Nor Azura Md; Aripin, Rasimah; Yusop, Noorezatty Mohd

    2015-02-01

    Microarray involves of placing an orderly arrangement of thousands of gene sequences in a grid on a suitable surface. The technology has made a novelty discovery since its development and obtained an increasing attention among researchers. The widespread of microarray technology is largely due to its ability to perform simultaneous analysis of thousands of genes in a massively parallel manner in one experiment. Hence, it provides valuable knowledge on gene interaction and function. The microarray data set typically consists of tens of thousands of genes (variables) from just dozens of samples due to various constraints. Therefore, the sample covariance matrix in Hotelling's T2 statistic is not positive definite and become singular, thus it cannot be inverted. In this research, the Hotelling's T2 statistic is combined with a shrinkage approach as an alternative estimation to estimate the covariance matrix to detect significant gene sets. The use of shrinkage covariance matrix overcomes the singularity problem by converting an unbiased to an improved biased estimator of covariance matrix. Robust trimmed mean is integrated into the shrinkage matrix to reduce the influence of outliers and consequently increases its efficiency. The performance of the proposed method is measured using several simulation designs. The results are expected to outperform existing techniques in many tested conditions.

  11. Development and Operation of an Automatic Rotor Trim Control System for the UH-60 Individual Blade Control Wind Tunnel Test

    Science.gov (United States)

    Theodore, Colin R.; Tischler, Mark B.

    2010-01-01

    An automatic rotor trim control system was developed and successfully used during a wind tunnel test of a full-scale UH-60 rotor system with Individual Blade Control (IBC) actuators. The trim control system allowed rotor trim to be set more quickly, precisely and repeatably than in previous wind tunnel tests. This control system also allowed the rotor trim state to be maintained during transients and drift in wind tunnel flow, and through changes in IBC actuation. The ability to maintain a consistent rotor trim state was key to quickly and accurately evaluating the effect of IBC on rotor performance, vibration, noise and loads. This paper presents details of the design and implementation of the trim control system including the rotor system hardware, trim control requirements, and trim control hardware and software implementation. Results are presented showing the effect of IBC on rotor trim and dynamic response, a validation of the rotor dynamic simulation used to calculate the initial control gains and tuning of the control system, and the overall performance of the trim control system during the wind tunnel test.

  12. Identification and characterization of a nuclear localization signal of TRIM28 that overlaps with the HP1 box

    International Nuclear Information System (INIS)

    Moriyama, Tetsuji; Sangel, Percival; Yamaguchi, Hiroki; Obuse, Chikashi; Miyamoto, Yoichi; Oka, Masahiro; Yoneda, Yoshihiro

    2015-01-01

    Tripartite motif-containing 28 (TRIM28) is a transcription regulator, which forms a repressor complex containing heterochromatin protein 1 (HP1). Here, we report identification of a nuclear localization signal (NLS) within the 462-494 amino acid region of TRIM28 that overlaps with its HP1 binding site, HP1 box. GST-pulldown experiments revealed the interaction of the arginine-rich TRIM28 NLS with various importin α subtypes (α1, α2 and α4). In vitro transport assay demonstrated that nuclear localization of GFP-TRIM28 NLS is mediated by importin αs, in conjunction with importin β1 and Ran. Further, we demonstrated that HP1 and importin αs compete for binding to TRIM28. Together, our findings suggest that importin α has an essential role in the nuclear delivery and preferential HP1 interaction of TRIM28. - Highlights: • TRIM28 contains an NLS within the 462-494 amino acid region. • The nuclear import of TRIM28 is mediated by importin α/importin β1. • TRIM28 NLS overlaps with HP1 Box. • HP1 and importin α compete for binding to TRIM28

  13. Identification and characterization of a nuclear localization signal of TRIM28 that overlaps with the HP1 box

    Energy Technology Data Exchange (ETDEWEB)

    Moriyama, Tetsuji; Sangel, Percival [Laboratory of Nuclear Transport Dynamics, National Institutes of Biomedical Innovation, Health and Nutrition (NIBIOHN), Osaka 567-0085 (Japan); Yamaguchi, Hiroki [School of Medicine, Osaka University, Osaka 565-0871 (Japan); Obuse, Chikashi [Graduate School of Life Science, Hokkaido University, Sapporo 001-0021 (Japan); Miyamoto, Yoichi [Laboratory of Nuclear Transport Dynamics, National Institutes of Biomedical Innovation, Health and Nutrition (NIBIOHN), Osaka 567-0085 (Japan); Oka, Masahiro, E-mail: moka@nibiohn.go.jp [Laboratory of Nuclear Transport Dynamics, National Institutes of Biomedical Innovation, Health and Nutrition (NIBIOHN), Osaka 567-0085 (Japan); Laboratory of Biomedical Innovation, Graduate School of Pharmaceutical Sciences, Osaka University, Osaka 565-0871 (Japan); Yoneda, Yoshihiro, E-mail: y-yoneda@nibiohn.go.jp [National Institutes of Biomedical Innovation, Health and Nutrition (NIBIOHN), Osaka 567-0085 (Japan); Laboratory of Biomedical Innovation, Graduate School of Pharmaceutical Sciences, Osaka University, Osaka 565-0871 (Japan)

    2015-07-03

    Tripartite motif-containing 28 (TRIM28) is a transcription regulator, which forms a repressor complex containing heterochromatin protein 1 (HP1). Here, we report identification of a nuclear localization signal (NLS) within the 462-494 amino acid region of TRIM28 that overlaps with its HP1 binding site, HP1 box. GST-pulldown experiments revealed the interaction of the arginine-rich TRIM28 NLS with various importin α subtypes (α1, α2 and α4). In vitro transport assay demonstrated that nuclear localization of GFP-TRIM28 NLS is mediated by importin αs, in conjunction with importin β1 and Ran. Further, we demonstrated that HP1 and importin αs compete for binding to TRIM28. Together, our findings suggest that importin α has an essential role in the nuclear delivery and preferential HP1 interaction of TRIM28. - Highlights: • TRIM28 contains an NLS within the 462-494 amino acid region. • The nuclear import of TRIM28 is mediated by importin α/importin β1. • TRIM28 NLS overlaps with HP1 Box. • HP1 and importin α compete for binding to TRIM28.

  14. TRIM44 Is a Poor Prognostic Factor for Breast Cancer Patients as a Modulator of NF-κB Signaling.

    Science.gov (United States)

    Kawabata, Hidetaka; Azuma, Kotaro; Ikeda, Kazuhiro; Sugitani, Ikuko; Kinowaki, Keiichi; Fujii, Takeshi; Osaki, Akihiko; Saeki, Toshiaki; Horie-Inoue, Kuniko; Inoue, Satoshi

    2017-09-08

    Many of the tripartite motif (TRIM) proteins function as E3 ubiquitin ligases and are assumed to be involved in various events, including oncogenesis. In regard to tripartite motif-containing 44 (TRIM44), which is an atypical TRIM family protein lacking the RING finger domain, its pathophysiological significance in breast cancer remains unknown. We performed an immunohistochemical study of TRIM44 protein in clinical breast cancer tissues from 129 patients. The pathophysiological role of TRIM44 in breast cancer was assessed by modulating TRIM44 expression in MCF-7 and MDA-MB-231 breast cancer cells. TRIM44 strong immunoreactivity was significantly associated with nuclear grade ( p = 0.033), distant disease-free survival ( p = 0.031) and overall survival ( p = 0.027). Multivariate analysis revealed that the TRIM44 status was an independent prognostic factor for distant disease-free survival ( p = 0.005) and overall survival ( p = 0.002) of patients. siRNA-mediated TRIM44 knockdown significantly decreased the proliferation of MCF-7 and MDA-MB-231 cells and inhibited the migration of MDA-MB-231 cells. Microarray analysis and qRT-PCR showed that TRIM44 knockdown upregulated CDK19 and downregulated MMP1 in MDA-MB-231 cells. Notably, TRIM44 knockdown impaired nuclear factor-kappa B (NF-κB)-mediated transcriptional activity stimulated by tumor necrosis factor α (TNFα). Moreover, TRIM44 knockdown substantially attenuated the TNFα-dependent phosphorylation of the p65 subunit of NF-κB and IκBα in both MCF-7 and MDA-MB-231 cells. TRIM44 would play a role in the progression of breast cancer by promoting cell proliferation and migration, as well as by enhancing NF-κB signaling.

  15. Selecting Health Care Improvement Projects: A Methodology Integrating Cause-and-Effect Diagram and Analytical Hierarchy Process.

    Science.gov (United States)

    Testik, Özlem Müge; Shaygan, Amir; Dasdemir, Erdi; Soydan, Guray

    It is often vital to identify, prioritize, and select quality improvement projects in a hospital. Yet, a methodology, which utilizes experts' opinions with different points of view, is needed for better decision making. The proposed methodology utilizes the cause-and-effect diagram to identify improvement projects and construct a project hierarchy for a problem. The right improvement projects are then prioritized and selected using a weighting scheme of analytical hierarchy process by aggregating experts' opinions. An approach for collecting data from experts and a graphical display for summarizing the obtained information are also provided. The methodology is implemented for improving a hospital appointment system. The top-ranked 2 major project categories for improvements were identified to be system- and accessibility-related causes (45%) and capacity-related causes (28%), respectively. For each of the major project category, subprojects were then ranked for selecting the improvement needs. The methodology is useful in cases where an aggregate decision based on experts' opinions is expected. Some suggestions for practical implementations are provided.

  16. Implications of the Integration of Computing Methodologies into Conventional Marketing Research upon the Quality of Students' Understanding of the Concept

    Science.gov (United States)

    Ayman, Umut; Serim, Mehmet Cenk

    2004-01-01

    It has been an ongoing concern among academicians teaching social sciences to develop a better methodology to ease understanding of students. Since verbal emphasis is at the core of the concepts within such disciplines it has been observed that the adequate or desired level of conceptual understanding of the students to transforms the theories…

  17. 76 FR 50188 - Notice of Proposed Methodology for the Delaware River and Bay Integrated List Water Quality...

    Science.gov (United States)

    2011-08-12

    ... Integrated List Water Quality Assessment AGENCY: Delaware River Basin Commission. ACTION: Notice. SUMMARY... Integrated List Water Quality Assessment is available for review and comment. DATES: Comments must be... should have the phrase ``Water Quality Assessment 2012'' in the subject line and should include the name...

  18. Development of a methodology for conducting an integrated HRA/PRA --. Task 1, An assessment of human reliability influences during LP&S conditions PWRs

    Energy Technology Data Exchange (ETDEWEB)

    Luckas, W.J.; Barriere, M.T.; Brown, W.S. [Brookhaven National Lab., Upton, NY (United States); Wreathall, J. [Wreathall (John) and Co., Dublin, OH (United States); Cooper, S.E. [Science Applications International Corp., McLean, VA (United States)

    1993-06-01

    During Low Power and Shutdown (LP&S) conditions in a nuclear power plant (i.e., when the reactor is subcritical or at less than 10--15% power), human interactions with the plant`s systems will be more frequent and more direct. Control is typically not mediated by automation, and there are fewer protective systems available. Therefore, an assessment of LP&S related risk should include a greater emphasis on human reliability than such an assessment made for power operation conditions. In order to properly account for the increase in human interaction and thus be able to perform a probabilistic risk assessment (PRA) applicable to operations during LP&S, it is important that a comprehensive human reliability assessment (HRA) methodology be developed and integrated into the LP&S PRA. The tasks comprising the comprehensive HRA methodology development are as follows: (1) identification of the human reliability related influences and associated human actions during LP&S, (2) identification of potentially important LP&S related human actions and appropriate HRA framework and quantification methods, and (3) incorporation and coordination of methodology development with other integrated PRA/HRA efforts. This paper describes the first task, i.e., the assessment of human reliability influences and any associated human actions during LP&S conditions for a pressurized water reactor (PWR).

  19. Uma abordagem metodológica para o desenvolvimento de sistemas automatizados e integrados de manufatura A methodological approach to automated and integrated manufacturing systems development

    Directory of Open Access Journals (Sweden)

    Marco Antonio Busetti de Paula

    2008-01-01

    Full Text Available Este trabalho apresenta uma metodologia de projeto aplicada a sistemas automatizados e integrados de manufatura. A metodologia consiste em um desenvolvimento cíclico de três etapas - modelagem, síntese e implementação - até o atendimento da aplicação demandada para o sistema real, resultando no projeto do sistema automatizado integrado. Esta forma de desenvolvimento permite uma revisão contínua dos resultados obtidos em cada etapa. Para testar e validar a metodologia, é apresentado um exemplo de re-projeto de um protótipo de sistema de manufatura em função da necessidade de inserção de um novo produto.This paper presents a methodology of project applied to automated and integrated manufacturing systems. The methodology consists of a cyclic three stages development - modeling, synthesis and implementation - till the accomplishment of the application required by the real system, resulting in the project of the automated and integrated system. This kind of development allows a continuous revision of the results of each stage. To submit to a test and to validate the methodology, it is given an example of a re-project of a prototype of a manufacturing system at the time of the introduction of a new product on the market.

  20. Dynamic event Tress applied to sequences Full Spectrum LOCA. Calculating the frequency of excedeence of damage by integrated Safety Analysis Methodology

    International Nuclear Information System (INIS)

    Gomez-Magan, J. J.; Fernandez, I.; Gil, J.; Marrao, H.; Queral, C.; Gonzalez-Cadelo, J.; Montero-Mayorga, J.; Rivas, J.; Ibane-Llano, C.; Izquierdo, J. M.; Sanchez-Perea, M.; Melendez, E.; Hortal, J.

    2013-01-01

    The Integrated Safety Analysis (ISA) methodology, developed by the Spanish Nuclear Safety council (CSN), has been applied to obtain the dynamic Event Trees (DETs) for full spectrum Loss of Coolant Accidents (LOCAs) of a Westinghouse 3-loop PWR plant. The purpose of this ISA application is to obtain the Damage Excedence Frequency (DEF) for the LOCA Event Tree by taking into account the uncertainties in the break area and the operator actuation time needed to cool down and de pressurize reactor coolant system by means of steam generator. Simulations are performed with SCAIS, a software tool which includes a dynamic coupling with MAAP thermal hydraulic code. The results show the capability of the ISA methodology to obtain the DEF taking into account the time uncertainty in human actions. (Author)

  1. METODOLOGÍA DE DISEÑO ORGANIZACIONAL INTEGRANDO ENFOQUE A PROCESOS Y COMPETENCIAS / METHODOLOGY OF ORGANIZATIONAL DESIGN INTEGRATING PROCESS APPROACH AND COMPETENCIES

    Directory of Open Access Journals (Sweden)

    Iraida Justina Rodríguez-González

    2012-04-01

    Full Text Available La Metodología de Diseño Organizacional responde a la introducción de formas organizativas basadas en el diseño de procesos, la estrategia y la gestión por competencias; integradas con los sistemas y tecnologías de la información. El modelo de diseño tiene como objetivo fundamental brindar una herramienta que permita diseñar una organización de nueva creación al tiempo que se va construyendo, sustentado en una plataforma integrada. La aplicación realizada en el Complejo de Investigaciones Tecnológicas Integradas (CITI demuestra la factibilidad de la metodología en las condiciones actuales y los resultados obtenidos avalan los procedimientos que la hacen funcional para Cuba y adaptable a objetivos similares en otros países.AbstractThe Methodology of Organizational Design corresponds to the introduction of organizational forms based on process design, strategy and management by competencies, which are integrated with the systems and information technologies. The design model aims to provide a tool to design a new organization while it is constructed, based on an integrated platform. The application carried out in the Complex of Integrated Technological Investigations (CITI, in its Spanish acronym, demonstrates the feasibility of the methodology under the current conditions and the obtained results endorse the procedures that make it functional for Cuba and adaptable to similar objectives in other countries.

  2. Exploring the integration of the human as a flexibility factor in CPS enabled manufacturing environments: Methodology and results

    OpenAIRE

    Fantini, P.; Tavola, G.; Taisch, M.; Barbosa, José; Leitão, Paulo; Liu, Y.; Sayed, M.S.; Lohse, N.

    2016-01-01

    Cyber Physical Systems (CPS) are expected to shape the evolution of production towards the fourth industrial revolution named Industry 4.0. The increasing integration of manufacturing processes and the strengthening of the autonomous capabilities of manufacturing systems make investigating the role of humans a primary research objective in view of emerging social and demographic megatrends. Understanding how the employees can be better integrated to enable increased flexibility in manufacturi...

  3. Regulatory road maps for the integration of intermittent electricity generation: Methodology development and the case of The Netherlands

    International Nuclear Information System (INIS)

    Welle, Adriaan J. van der; Joode, Jeroen de

    2011-01-01

    The envisaged increase in the share of electricity generation from intermittent renewable energy sources (RES-E) like wind and photovoltaics will pose challenges to the existing electricity system. A successful integration of these sources requires a cost-efficient use of system flexibility. The literature on the options to improve system flexibility, and thus the costs of successfully integrating intermittent electricity generating units, is still growing but what is lacking is an overarching systematic view on when to adopt which option in particular energy systems. This paper aims to bridge this gap in literature. We use existing insights on market and network integration of intermittent electricity sources within a regulatory road map framework. The framework allows policy makers and other electricity system stakeholders to arrive at a consistent strategy in dealing with integration issues over a longer period of time. In this contribution we present and explain the framework and apply it for the case of The Netherlands. - Highlights: → Successful integration of intermittent electricity generation requires a cost-efficient use of system flexibility. → An overarching systematic view on when to adopt which flexibility option in particular energy systems was lacking. → We identify a consistent strategy in dealing with integration issues over a longer period of time. → We present this regulatory road map framework and apply it for the case of The Netherlands.

  4. TRIM24 promotes glioma progression and enhances chemoresistance through activation of the PI3K/Akt signaling pathway.

    Science.gov (United States)

    Zhang, L-H; Yin, A-A; Cheng, J-X; Huang, H-Y; Li, X-M; Zhang, Y-Q; Han, N; Zhang, X

    2015-01-29

    The tripartite motif protein TRIM24 (tripartite motif-containing 24) has been found to play distinct roles in tumor development and progression, according to different tumor contexts. However, it remains elusive whether TRIM24 plays a role in malignant gliomas that are the most common and deadly primary brain tumors in adults. We report here that TRIM24 expression is positively correlated with glioma malignancy and is negatively associated with prognosis of patients with newly diagnosed glioblastoma, which is the most malignant form of gliomas but displays highly heterogeneous clinical outcome. The multivariate Cox regression analysis demonstrates the independent predictive value of TRIM24 expression level for overall and progression-free survival. Knockdown of TRIM24 suppresses cell proliferation, cell cycle progression, clone formation and in vivo tumor development, whereas overexpression of TRIM24 promotes cell growth. Chromatin immunoprecipitation, real-time reverse transcription-PCR and mutation analyses demonstrate that TRIM24 binds to the PIK3CA promoter via its PHD-Bromo domain to activate the transcription of PIK3CA gene, thus enhancing phosphatidylinositide 3-kinase (PI3K)/Akt signaling. The pan-PI3K inhibitor LY294002 and small interfering RNA targeting PIK3CA both abrogate the growth-promoting effect of TRIM24. Moreover, TRIM24 regulates the expression of DNA repair enzyme O(6)-methylguanine-DNA methyltransferase (MGMT) through PI3K/Akt/nuclear factor-κB signaling transduction and enhances resistance to temozolomide, the standard chemotherapeutic agent for glioblastoma. Finally, glioblastoma patients with low TRIM24 expression benefit from chemotherapy, whereas those with high TRIM24 expression do not have such benefit. Our results suggest that TRIM24 might serve as a potential prognostic marker and therapeutic target for the management of malignant gliomas.

  5. The Transcriptional Repressive Activity of KRAB Zinc Finger Proteins Does Not Correlate with Their Ability to Recruit TRIM28.

    Directory of Open Access Journals (Sweden)

    Kristin E Murphy

    Full Text Available KRAB domain Zinc finger proteins are one of the most abundant families of transcriptional regulators in higher vertebrates. The prevailing view is that KRAB domain proteins function as potent transcriptional repressors by recruiting TRIM28 and promoting heterochromatin spreading. However, the extent to which all KRAB domain proteins are TRIM28-dependent transcriptional repressors is currently unclear. Our studies on mouse ZFP568 revealed that TRIM28 recruitment by KRAB domain proteins is not sufficient to warrant transcriptional repressive activity. By using luciferase reporter assays and yeast two-hybrid experiments, we tested the ability of ZFP568 and other mouse KRAB domain proteins to repress transcription and bind TRIM28. We found that some mouse KRAB domain proteins are poor transcriptional repressors despite their ability to recruit TRIM28, while others showed strong KRAB-dependent transcriptional repression, but no TRIM28 binding. Together, our results show that the transcriptional repressive activity of KRAB-ZNF proteins does not correlate with their ability to recruit TRIM28, and provide evidence that KRAB domains can regulate transcription in a TRIM28-independent fashion. Our findings challenge the current understanding of the molecular mechanisms used by KRAB domain proteins to control gene expression and highlight that a high percentage of KRAB domain proteins in the mouse genome differ from the consensus KRAB sequence at amino acid residues that are critical for TRIM28 binding and/or repressive activity.

  6. Molecular characterization of a CpTRIM35-like protein and its splice variants from whitespotted bamboo shark (Chiloscyllium plagiosum)

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Xinshang, E-mail: sanmaosound@163.com; Zhao, Heng, E-mail: hengzhao2000@gmail.com; Chen, Yeyu, E-mail: cyyleaf@126.com; Luo, Huiying, E-mail: luohuiying@caas.cn; Yao, Bin, E-mail: binyao@caas.cn

    2014-10-24

    Highlights: • A TRIM gene and three splice variants were firstly cloned from elasmobranch fish. • The genes were constitutively expressed with high levels in spleen and kidney. • The gene products were distributed in cytoplasm alone or cytoplasm and nucleus. • As E3 ubiquitin ligases, the proteins differed in immune responses to challenges. - Abstract: The tripartite motif (TRIM) proteins play important roles in a broad range of biological processes, including apoptosis, cell proliferation and innate immunity response. In this study, a TRIM gene and its three splice variants were cloned from an elasmobranch fish—whitespotted bamboo shark (Chiloscyllium plagiosum Bennett). Phylogenetic analysis indicated that the gene was closely related to TRIM35 homologs, thus termed CpTRIM35-like. Deduced CpTRIM35 has a RBCC-PRY/SPRY structure typical of TRIM proteins, and its splice variants (CpTRIM35-1–3) have different truncations at the C-terminus. The gene products were constitutively expressed in adult sharks with the highest levels in spleen and kidney. The different subcellular locations, upregulation upon LPS and poly I:C stimulation, and significant E3 ubiquitin ligase activities suggested their different roles in immune responses as an E3 ubiquitin ligase. This is the first TRIM protein ever characterized in elasmobranch fish.

  7. Molecular characterization of a CpTRIM35-like protein and its splice variants from whitespotted bamboo shark (Chiloscyllium plagiosum)

    International Nuclear Information System (INIS)

    Zhang, Xinshang; Zhao, Heng; Chen, Yeyu; Luo, Huiying; Yao, Bin

    2014-01-01

    Highlights: • A TRIM gene and three splice variants were firstly cloned from elasmobranch fish. • The genes were constitutively expressed with high levels in spleen and kidney. • The gene products were distributed in cytoplasm alone or cytoplasm and nucleus. • As E3 ubiquitin ligases, the proteins differed in immune responses to challenges. - Abstract: The tripartite motif (TRIM) proteins play important roles in a broad range of biological processes, including apoptosis, cell proliferation and innate immunity response. In this study, a TRIM gene and its three splice variants were cloned from an elasmobranch fish—whitespotted bamboo shark (Chiloscyllium plagiosum Bennett). Phylogenetic analysis indicated that the gene was closely related to TRIM35 homologs, thus termed CpTRIM35-like. Deduced CpTRIM35 has a RBCC-PRY/SPRY structure typical of TRIM proteins, and its splice variants (CpTRIM35-1–3) have different truncations at the C-terminus. The gene products were constitutively expressed in adult sharks with the highest levels in spleen and kidney. The different subcellular locations, upregulation upon LPS and poly I:C stimulation, and significant E3 ubiquitin ligase activities suggested their different roles in immune responses as an E3 ubiquitin ligase. This is the first TRIM protein ever characterized in elasmobranch fish

  8. TRIM32 promotes retinoic acid receptor α-mediated differentiation in human promyelogenous leukemic cell line HL60

    International Nuclear Information System (INIS)

    Sato, Tomonobu; Okumura, Fumihiko; Iguchi, Akihiro; Ariga, Tadashi; Hatakeyama, Shigetsugu

    2012-01-01

    Highlights: ► TRIM32 enhanced RARα-mediated transcriptional activity even in the absence of RA. ► TRIM32 stabilized RARα in the human promyelogenous leukemic cell line HL60. ► Overexpression of TRIM32 in HL60 cells induced granulocytic differentiation. ► TRIM32 may function as a coactivator for RARα-mediated transcription in APL cells. -- Abstract: Ubiquitination, one of the posttranslational modifications, appears to be involved in the transcriptional activity of nuclear receptors including retinoic acid receptor α (RARα). We previously reported that an E3 ubiquitin ligase, TRIM32, interacts with several important proteins including RARα and enhances transcriptional activity of RARα in mouse neuroblastoma cells and embryonal carcinoma cells. Retinoic acid (RA), which acts as a ligand to nuclear receptors including RARα, plays crucial roles in development, differentiation, cell cycles and apoptosis. In this study, we found that TRIM32 enhances RARα-mediated transcriptional activity even in the absence of RA and stabilizes RARα in the human promyelogenous leukemic cell line HL60. Moreover, we found that overexpression of TRIM32 in HL60 cells suppresses cellular proliferation and induces granulocytic differentiation even in the absence of RA. These findings suggest that TRIM32 functions as one of the coactivators for RARα-mediated transcription in acute promyelogenous leukemia (APL) cells, and thus TRIM32 may become a potentially therapeutic target for APL.

  9. Molecular Characterization, Tissue Distribution and Expression, and Potential Antiviral Effects of TRIM32 in the Common Carp (Cyprinus carpio)

    Science.gov (United States)

    Wang, Yeda; Li, Zeming; Lu, Yuanan; Hu, Guangfu; Lin, Li; Zeng, Lingbing; Zhou, Yong; Liu, Xueqin

    2016-01-01

    Tripartite motif-containing protein 32 (TRIM32) belongs to the tripartite motif (TRIM) family, which consists of a large number of proteins containing a RING (Really Interesting New Gene) domain, one or two B-box domains, and coiled coil motif followed by different C-terminal domains. The TRIM family is known to be implicated in multiple cellular functions, including antiviral activity. However, it is presently unknown whether TRIM32 of common carp (Cyprinus carpio) has the antiviral effect. In this study, the sequence, expression, and antiviral function of TRIM32 homolog from common carp were analyzed. The full-length coding sequence region of trim32 was cloned from common carp. The results showed that the expression of TRIM32 (mRNA) was highest in the brain, remained stably expressed during embryonic development, and significantly increased following spring viraemia of carp virus (SVCV) infection. Transient overexpression of TRIM32 in affected Epithelioma papulosum cyprinid cells led to significant decrease of SVCV production as compared to the control group. These results suggested a potentially important role of common carp TRIM32 in enhancing host immune response during SVCV infection both in vivo and in vitro. PMID:27735853

  10. Methodological guide for the integration of the evaluation in the study plan d at “Nancy Uranga Romagoza” Faculty

    Directory of Open Access Journals (Sweden)

    Bienvenido Emilio Viera-Sánchez

    2013-08-01

    Full Text Available The integrating evaluation conception in the Study Plan D of the Physical Culture career will be always a pertinent and current topic, according to the new orientations about evaluation which indicate the final test realization in all subjects. This fact demands from a revision of the integration as a way to establish an appropriate equilibration of the evaluation in the academic year, as well as the inclusion of the state test like a form of studies' ending, occasion when the student shall solve a physical culture problem in one of the professional performance fields, which solution will certainly have a remarkable integrating character. As a result of a carried out study there is an instructive material for the teachers that contains different ways to integrate the contents of the subjects, disciplines and academic years in the third school year integrating test of Physical Education Didactics. In this kind of evaluation it can be better seen the students' difficulties on professional competences. Besides the exam's numbers reduced and the self preparation time saving, as well as result's quality are improved.

  11. TRIM56-mediated monoubiquitination of cGAS for cytosolic DNA sensing.

    Science.gov (United States)

    Seo, Gil Ju; Kim, Charlotte; Shin, Woo-Jin; Sklan, Ella H; Eoh, Hyungjin; Jung, Jae U

    2018-02-09

    Intracellular nucleic acid sensors often undergo sophisticated modifications that are critical for the regulation of antimicrobial responses. Upon recognition of DNA, the cytosolic sensor cyclic GMP-AMP (cGAMP) synthase (cGAS) produces the second messenger cGAMP, which subsequently initiates downstream signaling to induce interferon-αβ (IFNαβ) production. Here we report that TRIM56 E3 ligase-induced monoubiquitination of cGAS is important for cytosolic DNA sensing and IFNαβ production to induce anti-DNA viral immunity. TRIM56 induces the Lys335 monoubiquitination of cGAS, resulting in a marked increase of its dimerization, DNA-binding activity, and cGAMP production. Consequently, TRIM56-deficient cells are defective in cGAS-mediated IFNαβ production upon herpes simplex virus-1 (HSV-1) infection. Furthermore, TRIM56-deficient mice show impaired IFNαβ production and high susceptibility to lethal HSV-1 infection but not to influenza A virus infection. This adds TRIM56 as a crucial component of the cytosolic DNA sensing pathway that induces anti-DNA viral innate immunity.

  12. Endoscopic removal and trimming of distal self-expandable metallic biliary stents

    Science.gov (United States)

    Ishii, Kentaro; Itoi, Takao; Sofuni, Atsushi; Itokawa, Fumihide; Tsuchiya, Takayoshi; Kurihara, Toshio; Tsuji, Shujiro; Ikeuchi, Nobuhito; Umeda, Junko; Moriyasu, Fuminori; Tsuchida, Akihiko

    2011-01-01

    AIM: To evaluate the efficacy and safety of endoscopic removal and trimming of self-expandable metallic stents (SEMS). METHODS: All SEMS had been placed for distal biliary strictures. Twenty-seven endoscopic procedures were performed in 19 patients in whom SEMS (one uncovered and 18 covered) removal had been attempted, and 8 patients in whom stent trimming using argon plasma coagulation (APC) had been attempted at Tokyo Medical University Hospital. The APC settings were: voltage 60-80 W and gas flow at 1.5 L/min. RESULTS: The mean stent indwelling period for all patients in whom stent removal had been attempted was 113.7 ± 77.6 d (range, 8-280 d). Of the 19 patients in whom removal of the SEMS had been attempted, the procedure was successful in 14 (73.7%) without procedure-related adverse events. The indwelling period in the stent removable group was shorter than that in the unremovable group (94.9 ± 71.5 d vs 166.2 ± 76.2 d, P = 0.08). Stent trimming was successful for all patients with one minor adverse event consisting of self-limited hemorrhage. Trimming time ranged from 11 to 16 min. CONCLUSION: Although further investigations on larger numbers of cases are necessary to accumulate evidence, the present data suggested that stent removal and stent trimming is feasible and effective for stent-related complications. PMID:21677835

  13. Moving characteristics of single file passengers considering the effect of ship trim and heeling

    Science.gov (United States)

    Sun, Jinlu; Lu, Shouxiang; Lo, Siuming; Ma, Jian; Xie, Qimiao

    2018-01-01

    Ship listing and motion affects the movement pattern of passengers on board, thus pedestrian traffic and evacuation dynamics would be significantly different from those on level ground. To quantify the influence of ship listing and motion on passenger evacuation, we designed a ship corridor simulator, with which we performed single-file pedestrian movement experiments considering the effect of trim and heeling. Results indicated that density is not the only factor that affects pedestrian speed under ship trim or heeling conditions, for that both individual walking speed and group walking speed would be greatly attenuated due to the influence of the trim angles. However, heeling angles show less impact on speed when compared with trim angles. In addition, the speed correlation coefficient between the adjacent experimental subjects would be higher with larger angles and lower speed. Moreover, both female and male experimental subjects need similar distance headway for walking in different trim or heeling conditions. Furthermore, experimental subjects with lower individual walking speed need longer time headway to keep enough distance headway. This work will provide fundamental guidance to the development of evacuation models and the design of evacuation facilities on board.

  14. EHR-based disease registries to support integrated care in a health neighbourhood: an ontology-based methodology.

    Science.gov (United States)

    Liaw, Siaw-Teng; Taggart, Jane; Yu, Hairong

    2014-01-01

    Disease registries derived from Electronic Health Records (EHRs) are widely used for chronic disease management. We approached registries from the perspective of integrated care in a health neighbourhood, considering data quality issues such as semantic interoperability (consistency), accuracy, completeness and duplication. Our proposition is that a realist ontological approach is required to accurately identify patients in an EHR or data repository, assess data quality and fitness for use by the multidisciplinary integrated care team. We report on this approach with routinely collected data in a practice based research network in Australia.

  15. Application of an integrated multi-criteria decision making AHP-TOPSIS methodology for ETL software selection.

    Science.gov (United States)

    Hanine, Mohamed; Boutkhoum, Omar; Tikniouine, Abdessadek; Agouti, Tarik

    2016-01-01

    Actually, a set of ETL software (Extract, Transform and Load) is available to constitute a major investment market. Each ETL uses its own techniques for extracting, transforming and loading data into data warehouse, which makes the task of evaluating ETL software very difficult. However, choosing the right software of ETL is critical to the success or failure of any Business Intelligence project. As there are many impacting factors in the selection of ETL software, the same process is considered as a complex multi-criteria decision making (MCDM) problem. In this study, an application of decision-making methodology that employs the two well-known MCDM techniques, namely Analytic Hierarchy Process (AHP) and Technique for Order Preference by Similarity to Ideal Solution (TOPSIS) methods is designed. In this respect, the aim of using AHP is to analyze the structure of the ETL software selection problem and obtain weights of the selected criteria. Then, TOPSIS technique is used to calculate the alternatives' ratings. An example is given to illustrate the proposed methodology. Finally, a software prototype for demonstrating both methods is implemented.

  16. Contribution to the integration methodology of environment in the small and medium enterprises or industries: evaluation of environmental performances

    International Nuclear Information System (INIS)

    Personne, M.

    1998-01-01

    The integration of environmental criteria into industrial plants working is nowadays an obligation for companies. Implementation of an Environmental Management System (EMS) is a mean to integrate these criteria, and the system registration (by ISO 14001 or EMAS standards) enables companies to demonstrate the validity of their environmental behaviour to interested parties. Our experience in Small and Medium Enterprises (SMEs) has allowed us to note the inadequacy between their environmental integration level and EMS requirements. In addition to that, we have observed that environmental assessment methods, which could enable SMEs to make up for lost time, were not adapted to their specificities. However, two recent approaches are innovative: the first one is based on a progressive processes, the second one on an environmental information system, based on indicators construction. On the basis of existing methods study, improved with our SMEs experience, our approach consists of developing an environmental integration method, joining the progressive aspect (construction of a 'multi-phases' method) and the information treatment (exploitation of environmental data by indicators construction). We propose a four phases method, - environmental performance evaluation, internal and external results exploitation, process perpetuation -, setting up an information treatment system, by means of compliance, progress and monitoring indicators. Leading to implementation of an environmental performance continuous improvement cycle, this process enables companies to step forward EMS implementation. (author)

  17. Development of an integrated methodology for the sustainable environmental and socio-economic management of river ecosystems

    NARCIS (Netherlands)

    Koundouri, P.; Ker Rault, P.A.; Pergamalis, V.; Skianis, V.; Souliotis, I.

    2016-01-01

    The development of the Water Framework Directive aimed to establish an integrated framework of water management at European level. This framework revolves around inland surface waters, transitional waters, coastal waters and ground waters. In the process of achieving the environment and ecological

  18. Methodology for calculating perception of the user experience of the quality of monitored integrated telecommunications operator services

    NARCIS (Netherlands)

    2011-01-01

    The invention relates to a method for calculating perception of the user experience of the quality of monitored integrated telecommunications operator services. For this purpose, data from the monitoring of user services is used, along with questionnaires previously completed by a representative

  19. Integrated procedures and monitoring methodologies for thermographic investigations of architectural heritage: two applicative cases in Sicily, Italy

    International Nuclear Information System (INIS)

    Bianco, A.

    2013-01-01

    The paper explains some opportunities and limitations of thermographic investigations in terms of their capability to define the conservative conditions of architectural heritage and in terms of the historical recollection for a technical diagnosis. Different approaches are demonstrated in two case studies: the first integrates thermography with other investigative methods; the second combines thermographic monitoring with hygrothermal monitoring. (author)

  20. A Physics-Based Engineering Methodology for Calculating Soft Error Rates of Bulk CMOS and SiGe Heterojunction Bipolar Transistor Integrated Circuits

    Science.gov (United States)

    Fulkerson, David E.

    2010-02-01

    This paper describes a new methodology for characterizing the electrical behavior and soft error rate (SER) of CMOS and SiGe HBT integrated circuits that are struck by ions. A typical engineering design problem is to calculate the SER of a critical path that commonly includes several circuits such as an input buffer, several logic gates, logic storage, clock tree circuitry, and an output buffer. Using multiple 3D TCAD simulations to solve this problem is too costly and time-consuming for general engineering use. The new and simple methodology handles the problem with ease by simple SPICE simulations. The methodology accurately predicts the measured threshold linear energy transfer (LET) of a bulk CMOS SRAM. It solves for circuit currents and voltage spikes that are close to those predicted by expensive 3D TCAD simulations. It accurately predicts the measured event cross-section vs. LET curve of an experimental SiGe HBT flip-flop. The experimental cross section vs. frequency behavior and other subtle effects are also accurately predicted.

  1. A Systems Engineering Methodology for Designing and Planning the Built Environment—Results from the Urban Research Laboratory Nuremberg and Their Integration in Education

    Directory of Open Access Journals (Sweden)

    Philipp Geyer

    2014-04-01

    Full Text Available Sustainable urban development requires a long-term sector-integrative approach. This paper proposes a method of system analysis and partial simulation for urban structures for this purpose. It couples a discussion-based holistic approach for systems analysis and modelling of urban structures with quantitative modelling and simulation of partial scenarios that serve to examine specific questions regarding the long-term development of urban structures. In the first part, the application in the City Lab Nuremberg West, a multidisciplinary urban research laboratory, serves to develop the methodology and its illustration. The main objective is to examine the transition of the existing underperforming quarter to a sustainable and livable urban environment. Scenario-based experiments with respect to development paths determine robustness and risks of different configurations. The second part of the paper describes the transfer of the methodology to education. The approach serves to teach students in the Energy-Efficient and Sustainable Building master course program an integrative way of planning a sustainable built environment. The definition of educational objectives concerning the students’ understanding and management of systemic interdependencies of sustainability help assess the use of the method in the classroom. The aim is to provide them with the competence to develop strategies for complex situations while planning a sustainable built environment.

  2. Targeting TRIM5α in HIV Cure Strategies for the CRISPR-Cas9 Era

    Directory of Open Access Journals (Sweden)

    Daryl Anne Victoria Weatherley

    2017-11-01

    Full Text Available In the past decade, studies of innate immune activity against HIV-1 and other retroviruses have revealed a powerful array of host factors that can attack the virus at various stages of its life cycle in human and primate cells, raising the prospect that these antiviral factors could be manipulated in immunotherapeutic strategies for HIV infection. This has not proved straightforward: while HIV accessory genes encode proteins that subvert or destroy many of these restriction factors, others, such as human TRIM5α show limited potency against HIV-1. However, HIV-1 is much more susceptible to simian versions of TRIM5α: could this information be translated into the development of an effective gene therapy for HIV infection? Reigniting research into the restriction factor TRIM5α in the era of superior gene editing technology such as CRISPR-Cas9 presents an exciting opportunity to revisit this prospect.

  3. HIRFL-SSC trim coil currents calculation by conjugate gradients method

    International Nuclear Information System (INIS)

    Liu, W.

    2005-01-01

    For accelerating different kinds of ions to various energies, the HIRFL-SSC should form the corresponding isochronous magnetic field by its main coil and trim coils. Previously, there were errors in fitting the theoretical isochronous magnetic field in the small radius region, which led to some operation difficulties for ion acceleration in the inject region. After further investigation of the restrictive condition of the maximum current limitation, the trim coil currents for fitting the theoretical isochronous magnetic field were recalculated by the conjugate gradients method. Better results were obtained in the operation of HIRFL-SSC. This article introduces the procedure to calculate the trim coil currents. The calculation method of conjugate gradients is introduced and the fitting error is analysed. (author)

  4. Study of an integrated multi-criteria evaluation methodology on energy and environmental system based on MFM

    International Nuclear Information System (INIS)

    Liu, Jingquan; Yoshikawa, Hidekazu; Zhou, Yangping; Ouyang, Jun

    2005-01-01

    This paper presents a multi-criteria evaluation methodology based on Multilevel Flow Model (MFM), a graphical modeling language and embedding the perspective of sustainable development for energy and environmental system. A set of indicators reflecting resource utility efficiency, environmental effect, social and economic criteria according to the different concerns of stakeholder are defined. The graphical assessment process and outcome can provide help for general people to understand the evaluated object and its variables and to get better decision-making. Extension Evaluation Method is the first applied in the graphical assessment. The once-through option and reprocessing option of nuclear fuel cycle system will be examined by using the proposed approach. (author)

  5. Methodology for the integral comparison of nuclear reactors: selecting a reactor for Mexico; Metodologia para la comparacion integral de reactores nucleares: seleccion de un reactor para Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Reyes R, R.; Martin del Campo M, C. [UNAM, Facultad de Ingenieria, Laboratorio de Analisis de Ingenieria de Reactores Nucleares, Paseo Cuauhnahuac 8532, 62550 Jiutepec, Morelos (Mexico)]. e-mail: ricarera@yahoo.com.mx

    2006-07-01

    In this work it was built a methodology to compare nuclear reactors of third generation that can be contemplated for future electric planning in Mexico. This methodology understands the selection of the reactors to evaluate eliminating the reactors that still are not sufficiently mature at this time of the study. A general description of each reactor together with their main ones characteristic is made. It was carried out a study for to select the group of parameters that can serve as evaluation indicators, which are the characteristics of the reactors with specific values for each considered technology, and it was elaborated an evaluation matrix indicators including the reactors in the columns and those indicators in the lines. Since that none reactor is the best in all the indicators were necessary to use a methodology for multi criteria taking decisions that we are presented. It was used the 'Fuzzy Logic' technique, the which is based in those denominated diffuse groups and in a system of diffuse inference based on heuristic rules in the way 'If Then consequence> ', where the linguistic values of the condition and of the consequence is defined by diffuse groups, it is as well as the rules always they transform a diffuse group into another. Later on they combine all the diffuse outputs to create a single output and an inverse transformation is made that it transfers the output from the diffuse domain to the real one. They were carried out two studies one with the entirety of the indicators and another in which the indicators were classified in three approaches: the first one refers to indicators related with the planning of the plants inside the context of the general electric sector, the second approach includes indicators related with the characteristics of the fuel and the third it considers indicators related with the acting of the plant in safety and environmental impact. This second study allowed us to know the qualities of

  6. Integrated HPTLC-based Methodology for the Tracing of Bioactive Compounds in Herbal Extracts Employing Multivariate Chemometrics. A Case Study on Morus alba.

    Science.gov (United States)

    Chaita, Eliza; Gikas, Evagelos; Aligiannis, Nektarios

    2017-03-01

    In drug discovery, bioassay-guided isolation is a well-established procedure, and still the basic approach for the discovery of natural products with desired biological properties. However, in these procedures, the most laborious and time-consuming step is the isolation of the bioactive constituents. A prior identification of the compounds that contribute to the demonstrated activity of the fractions would enable the selection of proper chromatographic techniques and lead to targeted isolation. The development of an integrated HPTLC-based methodology for the rapid tracing of the bioactive compounds during bioassay-guided processes, using multivariate statistics. Materials and Methods - The methanol extract of Morus alba was fractionated employing CPC. Subsequently, fractions were assayed for tyrosinase inhibition and analyzed with HPTLC. PLS-R algorithm was performed in order to correlate the analytical data with the biological response of the fractions and identify the compounds with the highest contribution. Two methodologies were developed for the generation of the dataset; one based on manual peak picking and the second based on chromatogram binning. Results and Discussion - Both methodologies afforded comparable results and were able to trace the bioactive constituents (e.g. oxyresveratrol, trans-dihydromorin, 2,4,3'-trihydroxydihydrostilbene). The suggested compounds were compared in terms of R f values and UV spectra with compounds isolated from M. alba using typical bioassay-guided process. Chemometric tools supported the development of a novel HPTLC-based methodology for the tracing of tyrosinase inhibitors in M. alba extract. All steps of the experimental procedure implemented techniques that afford essential key elements for application in high-throughput screening procedures for drug discovery purposes. Copyright © 2017 John Wiley & Sons, Ltd. Copyright © 2017 John Wiley & Sons, Ltd.

  7. Electronic health records and disease registries to support integrated care in a health neighbourhood: an ontology-based methodology.

    Science.gov (United States)

    Liaw, Siaw-Teng; Taggart, Jane; Yu, Hairong; Rahimi, Alireza

    2014-01-01

    Disease registries derived from Electronic Health Records (EHRs) are widely used for chronic disease management (CDM). However, unlike national registries which are specialised data collections, they are usually specific to an EHR or organization such as a medical home. We approached registries from the perspective of integrated care in a health neighbourhood, considering data quality issues such as semantic interoperability (consistency), accuracy, completeness and duplication. Our proposition is that a realist ontological approach is required to systematically and accurately identify patients in an EHR or data repository of EHRs, assess intrinsic data quality and fitness for use by members of the multidisciplinary integrated care team. We report on this approach as applied to routinely collected data in an electronic practice based research network in Australia.

  8. Trimming algorithm of frequency modulation for CIAE-230 MeV proton superconducting synchrocyclotron model cavity

    Energy Technology Data Exchange (ETDEWEB)

    Li, Pengzhan, E-mail: lipengzhan@ciae.ac.cn; Zhang, Tianjue; Ji, Bin; Hou, Shigang; Guo, Juanjuan; Yin, Meng; Xing, Jiansheng; Lv, Yinlong; Guan, Fengping; Lin, Jun

    2017-01-21

    A new project, the 230 MeV proton superconducting synchrocyclotron for cancer therapy, was proposed at CIAE in 2013. A model cavity is designed to verify the frequency modulation trimming algorithm featuring a half-wave structure and eight sets of rotating blades for 1 kHz frequency modulation. Based on the electromagnetic (EM) field distribution analysis of the model cavity, the variable capacitor works as a function of time and the frequency can be written in Maclaurin series. Curve fitting is applied for theoretical frequency and original simulation frequency. The second-order fitting excels at the approximation given its minimum variance. Constant equivalent inductance is considered as an important condition in the calculation. The equivalent parameters of theoretical frequency can be achieved through this conversion. Then the trimming formula for rotor blade outer radius is found by discretization in time domain. Simulation verification has been performed and the results show that the calculation radius with minus 0.012 m yields an acceptable result. The trimming amendment in the time range of 0.328–0.4 ms helps to reduce the frequency error to 0.69% in Simulation C with an increment of 0.075 mm/0.001 ms, which is half of the error in Simulation A (constant radius in 0.328–0.4 ms). The verification confirms the feasibility of the trimming algorithm for synchrocyclotron frequency modulation. - Highlights: • A model cavity is designed to verify the trimming algorithm of frequency modulation. • The RF frequency is expressed by fitting approximation and Maclaurin series. • The variable capacitor of the cavity works as a function of time. • The trimming formula for blade radius is found by discretization in time domain. • The amendment solution helps to reduce the frequency error.

  9. S-nitrosylation of TRIM72 at cysteine 144 is critical for protection against oxidation-induced protein degradation and cell death.

    Science.gov (United States)

    Kohr, Mark J; Evangelista, Alicia M; Ferlito, Marcella; Steenbergen, Charles; Murphy, Elizabeth

    2014-04-01

    Oxidative stress and membrane damage following myocardial ischemia/reperfusion injury are important contributors to cardiomyocyte death and the loss of myocardial function. Our previous study identified cysteine 144 (C144) of tripartite motif-containing protein 72 (TRIM72) as a potential site for S-nitrosylation (SNO). TRIM72 is a cardioprotective membrane repair protein that can be both activated and targeted for degradation by different oxidative modifications. Consistent with the potential regulation of TRIM72 by various oxidative modifications, we found that SNO levels increased at C144 of TRIM72 with ischemic preconditioning. Therefore, to investigate the role of C144 in the regulation of TRIM72 function, we mutated C144 of TRIM72 to a serine residue (TRIM72(C144S)), and expressed either TRIM72(WT) or TRIM72(C144S) in HEK-293 cells, which lack endogenous TRIM72, in order to examine the effect of this mutation on the functional stability of TRIM72 and on cell survival. We hypothesized that SNO of TRIM72 stabilizes the protein, thus allowing for membrane repair and enhanced cell survival. Upon treatment with hydrogen peroxide (H2O2), we found that TRIM72(WT) levels were decreased, but not TRIM72(C144S) and this correlated with increased H2O2-induced cell death in TRIM72(WT) cells. Additionally, we found that treatment with the cardioprotective S-nitrosylating agent S-nitrosoglutathione (GSNO), was able to preserve TRIM72(WT) protein levels and enhance TRIM72(WT)-mediated cell survival, but had no effect on TRIM72(C144S) levels. Consistent with our hypothesis, GSNO was also found to increase SNO levels and inhibit H2O2-induced irreversible oxidation for TRIM72(WT) without affecting TRIM72(C144S). In further support of our hypothesis, GSNO blocked the ischemia/reperfusion-induced decrease in TRIM72 levels and reduced infarct size in a Langendorff-perfused heart model. The results of these studies have important implications for cardioprotection and suggest that

  10. Aircraft interior noise models - Sidewall trim, stiffened structures, and cabin acoustics with floor partition

    Science.gov (United States)

    Pope, L. D.; Wilby, E. G.; Willis, C. M.; Mayes, W. H.

    1983-01-01

    As part of the continuing development of an aircraft interior noise prediction model, in which a discrete modal representation and power flow analysis are used, theoretical results are considered for inclusion of sidewall trim, stiffened structures, and cabin acoustics with floor partition. For validation purposes, predictions of the noise reductions for three test articles (a bare ring-stringer stiffened cylinder, an unstiffened cylinder with floor and insulation, and a ring-stringer stiffened cylinder with floor and sidewall trim) are compared with measurements.

  11. Laser Trimming of CuAlMo Thin-Film Resistors: Effect of Laser Processing Parameters

    Science.gov (United States)

    Birkett, Martin; Penlington, Roger

    2012-08-01

    This paper reports the effect of varying laser trimming process parameters on the electrical performance of a novel CuAlMo thin-film resistor material. The films were prepared on Al2O3 substrates by direct-current (DC) magnetron sputtering, before being laser trimmed to target resistance value. The effect of varying key laser parameters of power, Q-rate, and bite size on the resistor stability and tolerance accuracy were systematically investigated. By reducing laser power and bite size and balancing this with Q-rate setting, significant improvements in resistor stability and resistor tolerance accuracies of less than ±0.5% were achieved.

  12. tclust: An R Package for a Trimming Approach to Cluster Analysis

    Directory of Open Access Journals (Sweden)

    2012-04-01

    Full Text Available Outlying data can heavily influence standard clustering methods. At the same time, clustering principles can be useful when robustifying statistical procedures. These two reasons motivate the development of feasible robust model-based clustering approaches. With this in mind, an R package for performing non-hierarchical robust clustering, called tclust, is presented here. Instead of trying to “fit” noisy data, a proportion α of the most outlying observations is trimmed. The tclust package efficiently handles different cluster scatter constraints. Graphical exploratory tools are also provided to help the user make sensible choices for the trimming proportion as well as the number of clusters to search for.

  13. The ability of White Leghorn hens with trimmed comb and wattles to thermoregulate.

    Science.gov (United States)

    Al-Ramamneh, D S; Makagon, M M; Hester, P Y

    2016-08-01

    It is estimated that each year over 19 million pullets in the United States have their combs partially trimmed at a young age to improve egg production and feed efficiency. A possible disadvantage of trimming is that the comb and wattles may be essential for thermoregulation during hot weather allowing for conductive cooling of the blood through vasodilation of superficial vessels in these integumentary tissues. The objective of this study was to investigate the effects of partial comb and wattle removal, performed at 21 d of age, on the ability of White Leghorns to thermoregulate before, during, and after an imposed heating episode that averaged 34.6°C for 50.5 h. An increase in mortality at 20 h and body temperature at 48 h post initiation of the heating episode demonstrated that hens with trimmed comb and wattles were not able to cope with heat stress as effectively as controls. The increase in wattle temperature in controls as compared to trimmed hens during the heating episode and following heat stress provides supportive evidence that blood pools to the peripheral surface for conductive heat loss. During high temperatures typical of summer, trimmed hens attempted to compensate for their lack of ability to transfer heat from their comb and wattles to the environment through increased proportion of panting and wing spreading. Under less extreme conditions with lowered ambient temperatures, the trimming of the comb and wattles did not impair the ability of hens to thermoregulate, as body temperatures and behavior were similar to controls with no mortality. Egg weight was the only production parameter adversely affected by the trimming of the comb and wattles as compared to controls. The implication is that hens need their combs and wattles to thermoregulate effectively during periods of high environmental temperature. Pullets should not be subjected to a comb and wattle trim if they are housed in laying facilities that are not appropriately cooled during the

  14. Integrated dynamic policy management methodology and system for strategic environmental assessment of golf course installation policy in Taiwan

    International Nuclear Information System (INIS)

    Chen, Ching-Ho; Liu, Wei-Lin; Liaw, Shu-Liang

    2011-01-01

    Strategic environmental assessment (SEA) focuses primarily on assessing how policies, plans, and programs (PPPs) influence the sustainability of the involved regions. However, the processes of assessing policies and developing management strategies for pollution load and resource use are usually separate in the current SEA system. This study developed a policy management methodology to overcome the defects generated during the above processes. This work first devised a dynamic management framework using the methods of systems thinking, system dynamics, and Managing for Results (MFRs). Furthermore, a driving force-pressure-state-impact-response (DPSIR) indicator system was developed. The golf course installation policy was applied as a case study. Taiwan, counties of Taiwan, and the golf courses within those individual counties were identified as a system, subsystems, and objects, respectively. This study identified an object-linked double-layer framework with multi-stage-option to simultaneously to quantify golf courses in each subsystem and determine ratios of abatement and allocation for pollution load and resource use of each golf course. The DPSIR indicator values for each item of each golf course in each subsystem are calculated based on the options taken in the two decision layers. The summation of indicator values for all items of all golf courses in all subsystems according to various options is defined as the sustainability value of the policy. An optimization model and a system (IDPMS) were developed to obtain the greatest sustainability value of the policy, while golf course quantity, human activity intensity, total quantities of pollution load and resource use are simultaneously obtained. The solution method based on enumeration of multiple bounds for objectives and constraints (EMBOC) was developed for the problem with 1.95 x 10 128 combinations of possible options to solve the optimal solution in ten minutes using a personal computer with 3.0 GHz CPU

  15. The effect of routine hoof trimming on locomotion score, ruminating time, activity and milk yield of dairy cows

    NARCIS (Netherlands)

    Hertem, van T.; Parmet, Y.; Steensels, M.; Maltz, E.; Antler, A.; Schlageter Tello, A.A.; Lokhorst, C.; Romanini, C.E.B.; Viazzi, S.; Bahr, C.; Berckmans, D.; Halachmi, I.

    2014-01-01

    The objective of this study was to quantify the effect of hoof trimming on cow behavior (ruminating time, activity, and locomotion score) and performance (milk yield) over time. Data were gathered from a commercial dairy farm in Israel where routine hoof trimming is done by a trained hoof trimmer

  16. The effect of preventive trimming on weight bearing and force balance on the claws of dairy cattle

    NARCIS (Netherlands)

    Tol, van der P.P.J.; Beek, van der S.S.; Metz, J.H.M.; Noordhuizen-Stassen, E.N.; Back, E.; Braam, C.R.; Weijs, W.A.

    2004-01-01

    Claw disorders and lameness in dairy cattle are an increasing problem of the modern dairy industry. To prevent claw disorders from evolving from the subclinical to the clinical stage, trimming is the management practice most routinely applied. The goal of preventive trimming (Toussaint-Raven method)

  17. Expression of TRIM28 correlates with proliferation and Bortezomib-induced apoptosis in B-cell non-Hodgkin lymphoma.

    Science.gov (United States)

    Zhang, Pei-Pei; Ding, Da-Zhi; Shi, Bing; Zhang, Shu-Qing; Gu, Ling-Li; Wang, Yu-Chan; Cheng, Chun

    2018-03-23

    Tripartite motif containing 28 (TRIM28) as a transcriptional co-repressor has been reported playing a role in regulating DNA damage response (DDR), cell differentiation, immune response, and tumorigenesis. The present study was performed to explore the biological function and clinical significance of TRIM28 in B-cell non-Hodgkin lymphoma (B-NHL). Results of the study displayed that high expression of TRIM28 was positively associated with the poorer survival of B-NHL patients as an independent prognostic factor. In addition, TRIM28 could promote the B-NHL cells proliferation through modulating cell cycle progression. The change of cyclinA, P21, and PCNA expression after TRIM28 expression modified further illustrated the mechanism in which TRIM28 participated in cell proliferation progression. Moreover, inhibition TRIM28 expression in B-NHL cells enhanced the sensibility to Bortezomib by regulating p53-mediated apoptosis pathway. Taken together, the present study showed that TRIM28 functions as a tumor promoter in B-NHL and may be a novel target for drug resistance to Bortezomib.

  18. Integration of biomass into urban energy systems for heat and power. Part I: An MILP based spatial optimization methodology

    International Nuclear Information System (INIS)

    Pantaleo, Antonio M.; Giarola, Sara; Bauen, Ausilio; Shah, Nilay

    2014-01-01

    Highlights: • MILP tool for optimal sizing and location of heating and CHP plants to serve residential energy demand. • Trade-offs between local vs centralized heat generation, district heating vs natural gas distribution systems. • Assessment of multi-biomass supply chains and biomass to biofuel processing technologies. • Assessment of the key factors influencing the use of biomass and district heating in residential areas. - Abstract: The paper presents a mixed integer linear programming (MILP) approach to optimize multi-biomass and natural gas supply chain strategic design for heat and power generation in urban areas. The focus is on spatial and temporal allocation of biomass supply, storage, processing, transport and energy conversion (heat and CHP) to match the heat demand of residential end users. The main aim lies on the representation of the relationships between the biomass processing and biofuel energy conversion steps, and on the trade-offs between centralized district heating plants and local heat generation systems. After a description of state of the art and research trends in urban energy systems and bioenergy modelling, an application of the methodology to a generic case study is proposed. With the assumed techno-economic parameters, biomass based thermal energy generation results competitive with natural gas, while district heating network results the main option for urban areas with high thermal energy demand density. Potential further applications of this model are also described, together with main barriers for development of bioenergy routes for urban areas

  19. Engaging Future Clinical Oncology Researchers: An Initiative to Integrate Teaching of Biostatistics and Research Methodology into Specialty Training.

    Science.gov (United States)

    Turner, S; Sundaresan, P; Mann, K; Pryor, D; Gebski, V; Shaw, T

    2016-05-01

    To evaluate the learner's perspectives on a novel workshop programme designed to improve skills in biostatistics, research methodology and critical appraisal in oncology. Trainees were surveyed anonymously at the completion of each annual workshop from 2012 to 2015. In total, 103 trainees in years 2-4 of training in radiation oncology responded, giving a 94% survey response rate. A 1 day workshop, designed by biostatisticians and radiation oncologist facilitators, is the central component of a programme teaching skills in biostatistics, research methods and critical appraisal. This links short didactic lectures about statistical concepts to interactive trainee discussions around discipline-related publications. The workshop was run in conjunction with the major radiation oncology clinical trials group meeting with alternating programmes (A and B). Most of the participants (44-47/47 for A and 48-55/56 for B), reported that their understanding of one or more individual topics improved as a result of teaching. Refinement of the workshop over time led to a more favourable perception of the 'optimal' balance between didactic/interactive teaching: nine of 27 (33%) 'optimal' responses seen in 2013 compared with 23 of 29 (79%) in 2015 (P research to illuminate key statistical concepts. Copyright © 2015 The Royal College of Radiologists. Published by Elsevier Ltd. All rights reserved.

  20. The research and practice of integrating conservation and development: Self-reflections by researchers on methodologies, objectives and influence

    Directory of Open Access Journals (Sweden)

    Maya Pasgaard

    2017-01-01

    Full Text Available This study examines the application of mixed-method and participatory approaches to conservation and development research. Both approaches were applied in a research project on the relationship between ecosystem governance and the wellbeing of local communities adjacent to a protected area in Laos. By encouraging four of the involved field researchers to reflect upon and expose their practical approaches as scientific experts (in terms of methodologies, objectives, reliability of results and research influence, this article aims to improve our learning from research practice and to promote reflexivity in research. The reflexive study presented here emphasizes the social and political context or real world situation against which research outputs can and should be evaluated, and retrospectively sheds light on the barriers to reach research objectives. In essence, the article addresses the relation between science and policy, and underlines the political undercurrent of conservation and development research in facilitating institutional change. The article outlines the very role of researchers in developing conservation policies, and provides a foundation for institutions and individual researchers to promote critical and constructive self-reflections in scientific practices.

  1. THE METHODOLOGY OF THE ANALYSIS OF CASE STUDY THROUGH THE INTEGRATION OF THE ROMA MINORITY INTO THE SOCIAL SYSTEM

    Directory of Open Access Journals (Sweden)

    Jelena Maksimović

    2017-06-01

    Full Text Available The Roma are an ethnic group that is spread throughout the world. Although there are poor ethnographic and historical notes about the origin of Roma on the basis of a study of legends and oral traditions, researchers who are engaged in Roma studies, often confirm that they originate from India. Their culture, habits, customs were mostly transmitted through the living word, from generation to generation. This research analyzed case studies of integration of the Roma minority in the social system. Special emphasis in research is aimed at analyzing stereotypes that arise from cultural patterns of Roma, given the fact that for them there are many different prejudices, while on the other hand, there is no access with critical analysis and does not indicate their specialty, which has its downside exactly in culture and patterns of behavior. The study analyzed how the traditional culture is important in the lives of Roma and how the social system treats this ethnic minority. Being a Rom in its original sense means to be human and to be equal with everyone, but paradoxically it is expected that non-Roma nation sets free of stereotypes and prejudices and to contribute to the integration and acceptance of Roma in our social system.

  2. Integrating Prevention of Mother to Child HIV Transmission competencies into the nursing curriculum: Methodological lessons from a university-based undergraduate programme.

    Science.gov (United States)

    Mbombo, Nomafrench; Bimerew, Million

    2012-11-14

    South Africa (SA) has the highest number of women infected with HIV and AIDS during pregnancy, which results in more than 70 000 infected babies being born each year AIDS is the major contributor to maternal and child morbidities and mortalities in the country. To combat this, the SA government has developed a national policy to prevent mother-to-child HIV transmission (PMTCT). However, for effective implementation of this policy, there is a dire need for a competent, skilled health worker to render the service. In response to this, the School of Nursing at the University of the Western Cape has integrated PMTCT competencies into the undergraduate Bachelor of Nursing Science curriculum. In this paper, we described teaching and learning approaches used to integrate PMTCT competencies, including the skills laboratory methodology and case-based learning, as well as a portfolio of evidence assessment tool. A quantitative descriptive design was used to analyse data collected from students in regard to assessment of PMTCT competencies achieved. The study used the conceptual framework of Lenburg's competency outcomes and performance assessment model, which focuses on competency development and assessment in a clinical environment. HIV competencies, including PMTCT, should be integrated both theoretically and at service delivery into other nursing and midwifery competencies, including assessment strategies. Provincial policies in provision of antiretrovirals by nurses and midwives become barriers to successful implementation of PMTCT, resulting in limited learning opportunities for students to practice PMTCT competencies. Further research is required to assess an attribute, affect, which is another prong for competencies.

  3. The Challenge of Integrating OHS into Industrial Project Risk Management: Proposal of a Methodological Approach to Guide Future Research (Case of Mining Projects in Quebec, Canada

    Directory of Open Access Journals (Sweden)

    Adel Badri

    2015-06-01

    Full Text Available Although risk management tools are put to good use in many industrial sectors, some large projects have been met with numerous problems due to failure to take occupational health and safety (OHS into consideration. In spite of the high level of risk and uncertainty associated with many industrial projects, the number of studies of methods for managing all known risks systematically remains small. Under effervescent economic conditions, industries must meet several challenges associated with frequent project start-ups. In highly complex and uncertain environments, rigorous management of risk remains indispensable for avoiding threats to the success of projects. Many businesses seek continually to create and improve integrated approaches to risk management. This article puts into perspective the complexity of the challenge of integrating OHS into industrial project risk management. A conceptual and methodological approach is proposed to guide future research focused on meeting this challenge. The approach is based on applying multi-disciplinary research modes to a complex industrial context in order to identify all scenarios likely to contain threats to humans or the environment. A case study is used to illustrate the potential of the proposed approach for application and its contribution to meeting the challenge of taking OHS into consideration. On-site researchers were able to develop a new approach that helped two mining companies in Quebec (Canada to achieve successful integration of OHS into expansion projects.

  4. An integrated model for reliability estimation of digital nuclear protection system based on fault tree and software control flow methodologies

    International Nuclear Information System (INIS)

    Kim, Man Cheol; Seong, Poong Hyun

    2000-01-01

    In the nuclear industry, the difficulty of proving the reliabilities of digital systems prohibits the widespread use of digital systems in various nuclear application such as plant protection system. Even though there exist a few models which are used to estimate the reliabilities of digital systems, we develop a new integrated model which is more realistic than the existing models. We divide the process of estimating the reliability of a digital system into two phases, a high-level phase and a low-level phase, and the boundary of two phases is the reliabilities of subsystems. We apply software control flow method to the low-level phase and fault tree analysis to the high-level phase. The application of the model to Dynamic Safety System(DDS) shows that the estimated reliability of the system is quite reasonable and realistic

  5. An integrated model for reliability estimation of digital nuclear protection system based on fault tree and software control flow methodologies

    International Nuclear Information System (INIS)

    Kim, Man Cheol; Seong, Poong Hyun

    2000-01-01

    In nuclear industry, the difficulty of proving the reliabilities of digital systems prohibits the widespread use of digital systems in various nuclear application such as plant protection system. Even though there exist a few models which are used to estimate the reliabilities of digital systems, we develop a new integrated model which is more realistic than the existing models. We divide the process of estimating the reliability of a digital system into two phases, a high-level phase and a low-level phase, and the boundary of two phases is the reliabilities of subsystems. We apply software control flow method to the low-level phase and fault tree analysis to the high-level phase. The application of the model of dynamic safety system (DSS) shows that the estimated reliability of the system is quite reasonable and realistic. (author)

  6. The methodological foundations of mutual integration of scientific knowledge in the field of physical education and sports and related sciences.

    Directory of Open Access Journals (Sweden)

    Kozina Zh.L.

    2012-02-01

    Full Text Available Possibilities of application of scientific knowledge in physical education and sport in contiguous scientific directions are considered. The advanced studies of leading specialists in area of physical education and sport are analysed. It is rotined that on the modern stage scientific developments in area of physical education and sport attained a level, when can be utillized in fundamental and applied sciences. Scientific researches in area of physical education and sport to the application scientific areas, such as pedagogics, psychology, design, programming et al are related. One of examples of mutual integration of scientific knowledge in area of physical education and sport there is theoretical conception of individualization of preparation of sportsmen.

  7. Integrating the Self and the Spirit: Strategies for Aligning Qualitative Research Teaching with Indigenous Methods, Methodologies, and Epistemology

    Directory of Open Access Journals (Sweden)

    Sarah K. Knudson

    2015-07-01

    Full Text Available Many universities internationally now make concerted efforts to promote curriculum development and classroom and campus cultures that recognize diversity in student viewpoints and life experiences. Increasingly, these efforts have involved promoting recognition and inclusion of indigenous knowledges in the university setting. If adopted in the classroom, the promotion of indigenous perspectives suggests exciting possibilities for teaching qualitative research critically. Existing educational resources, however, offer little guidance on achieving this through undergraduate qualitative methods teaching. Using examples of Canadian undergraduate teaching initiatives, I suggest that by integrating indigenous methods, perspectives, and epistemology, particularly through student opportunities for community-engaged learning and exposure to participatory action research, teaching qualitative research can promote critical recognition of multiple ways of knowing. URN: http://nbn-resolving.de/urn:nbn:de:0114-fqs150347

  8. TRIM29 Overexpression Promotes Proliferation and Survival of Bladder Cancer Cells through NF-κB Signaling.

    Science.gov (United States)

    Tan, Shu-Tao; Liu, Sheng-Ye; Wu, Bin

    2016-10-01

    TRIM29 overexpression has been reported in several human malignancies and showed correlation with cancer cell malignancy. The aim of the current study is to examine its clinical significance and biological roles in human bladder cancer tissues and cell lines. A total of 102 cases of bladder cancer tissues were examined for TRIM29 expression by immunohistochemistry. siRNA and plasmid transfection were performed in 5637 and BIU-87 cell lines. Cell Counting Kit-8, flow cytometry, western blot, and real-time polymerase chain reaction were performed to examine its biological roles and mechanism in bladder cancer cells. We found that TRIM29 overexpression showed correlation with invading depth (p=0.0087). Knockdown of TRIM29 expression in bladder cancer cell line 5637 inhibited cell growth rate and cell cycle transition while its overexpression in BIU-87 cells accelerated cell proliferation and cell cycle progression. TRIM29 overexpression also inhibited cell apoptosis induced by cisplatin. In addition, we demonstrated that TRIM29 depletion decreased while its overexpression led to upregulated expression of cyclin D1, cyclin E, and Bcl-2. We also showed that TRIM29 knockdown inhibited protein kinase C (PKC) and nuclear factor κB (NF-κB) signaling while its overexpression stimulated the PKC and NF-κB pathways. BAY 11-7082 (NF-κB inhibitor) partly attenuated the effect of TRIM29 on expression of cyclin and Bcl-2. Treatment with PKC inhibitor staurosporine resulted in ameliorated TRIM29 induced activation of NF-κB. The current study demonstrated that TRIM29 upregulates cyclin and Bcl family proteins level to facilitate malignant cell growth and inhibit drug-induced apoptosis in bladder cancer, possibly through PKC-NF-κB signaling pathways.

  9. Sample Size Determination for One- and Two-Sample Trimmed Mean Tests

    Science.gov (United States)

    Luh, Wei-Ming; Olejnik, Stephen; Guo, Jiin-Huarng

    2008-01-01

    Formulas to determine the necessary sample sizes for parametric tests of group comparisons are available from several sources and appropriate when population distributions are normal. However, in the context of nonnormal population distributions, researchers recommend Yuen's trimmed mean test, but formulas to determine sample sizes have not been…

  10. Application of a Broadband Active Vibration Control System to a Helicopter Trim Panel

    Science.gov (United States)

    Cabell, Randolph H.; Schiller, Noah H.; Simon, Frank

    2013-01-01

    This paper discusses testing of a broadband active vibration control concept on an interior trim panel in a helicopter cabin mockup located at ONERA's Centre de Toulouse. The control system consisted of twelve diamond-shaped piezoelectric actuators distributed around a 1.2m x 1.2m trim panel. Accelerometers were mounted at the four vertices of each diamond. The aspect ratio of the diamond was based on the dielectric constants of the piezoelectric material in order to create an actuator-sensor pair that was collocated over a broad frequency range. This allowed robust control to be implemented using simple, low power analog electronics. Initial testing on a thick acrylic window demonstrated the capability of the controller, but actuator performance was less satisfactory when mounted on a composite sandwich trim panel. This may have been due to the orthotropic nature of the trim panel, or due to its much higher stiffness relative to the acrylic window. Insights gained from a finite element study of the actuator-sensor-structural system are discussed.

  11. Introducing trimming and function ranking to Solid Works based on function analysis

    NARCIS (Netherlands)

    Chechurin, Leonid S.; Wits, Wessel Willems; Bakker, Hans M.; Cascini, G.; Vaneker, Thomas H.J.

    2011-01-01

    TRIZ based Function Analysis models existing products based on functional interactions between product parts. Such a function model description is the ideal starting point for product innovation. Design engineers can apply (TRIZ) methods such as trimming and function ranking to this function model

  12. Introducing Trimming and Function Ranking to SolidWorks based on Function Analysis

    NARCIS (Netherlands)

    Chechurin, L.S.; Wits, Wessel Willems; Bakker, Hans M.; Vaneker, Thomas H.J.

    2015-01-01

    TRIZ based Function Analysis models existing products based on functional interactions between product parts. Such a function model description is the ideal starting point for product innovation. Design engineers can apply (TRIZ) methods such as trimming and function ranking to this function model

  13. Mountain Plains Learning Experience Guide: Electrical Wiring. Course: Electrical Wiring Trim-Out.

    Science.gov (United States)

    Arneson, R.; And Others

    One of two individualized courses included in an electrical wiring curriculum, this course covers electrical materials installation for the trim-out stage. The course is comprised of five units: (1) Outlets, (2) Fixtures, (3) Switches, (4) Appliances, and (5) Miscellaneous. Each unit begins with a Unit Learning Experience Guide that gives…

  14. The influence of fat score and fat trimming on primal cut composition ...

    African Journals Online (AJOL)

    The objectives of this study were to evaluate the primal cut composition of South African lamb carcasses with different fat scores, and to identify cuts suitable for fat trimming. Sixty grain fed Dorper lambs (rams and ewes) were divided into three groups and slaughtered at 30, 36 and 42 kg. Chilled carcass sides were ...

  15. Glucosidase trimming inhibitors preferentially perturb T cell activation induced by CD2 mAb

    NARCIS (Netherlands)

    van Kemenade, F. J.; Rotteveel, F. T.; van den Broek, L. A.; Baars, P. A.; van Lier, R. A.; Miedema, F.

    1994-01-01

    Glycosidase trimming inhibitors may be used to study contribution of N-linked glycan moieties in T cell function. We have studied the effects of castanospermine (Cas), swainsonine (Swain), 1-deoxynojirimycin (dNM), and 1-deoxymannojirimycin (dMM) on T cell activation and differentiation. Our

  16. Genetic parameters for claw disorders and the effect of preselecting cows for trimming

    NARCIS (Netherlands)

    Spek, van der D.; Arendonk, van J.A.M.; Vallee, A.A.A.; Bovenhuis, H.

    2013-01-01

    Abstract Claw disorders are important traits relevant to dairy cattle breeding from an economical and welfare point of view. Selection for reduced claw disorders can be based on hoof trimmer records. Typically, not all cows in a herd are trimmed. Our objectives were to estimate heritabilities and

  17. Scoring of digital dermatitis during milking as an alternative to scoring in a hoof trimming chute

    DEFF Research Database (Denmark)

    Thomsen, Peter; Klaas, Ilka Christine; Bach, K.

    2008-01-01

    Digital dermatitis is a serious problem in dairy production in many countries. In many settings, it is important to evaluate the digital dermatitis status of individual cows or an entire dairy herd. Such an evaluation has traditionally been done in a hoof trimming chute. An evaluation in the milk......Digital dermatitis is a serious problem in dairy production in many countries. In many settings, it is important to evaluate the digital dermatitis status of individual cows or an entire dairy herd. Such an evaluation has traditionally been done in a hoof trimming chute. An evaluation...... in the milking parlor can take place without disturbing the cows to a large extent, it can be done using less labor compared with an evaluation in a hoof trimming chute, and is cheaper than using a chute. The objective was to evaluate the sensitivity and specificity of a rapid screening method for digital...... dermatitis in the milking parlor, without using any specialized tools and taking approximately 15 s/cow. All lactating cows in 3 commercial Danish dairy herds were included. Cows were first scored for the presence of digital dermatitis during milking and the next day all cows were scored during hoof trimming...

  18. Limit law of the iterated logarithm for B-valued trimmed sums

    Indian Academy of Sciences (India)

    Limit law of the iterated logarithm for B-valued trimmed sums. KE-ANG FU1, YUYANG QIU1,∗ and YELING TONG2. 1School of Statistics and Mathematics, Zhejiang Gongshang University,. Hangzhou 310018, China. 2Zhejiang Institute of Traditional Chinese Medicine, Hangzhou 310028, China. *Corresponding author.

  19. Limit law of the iterated logarithm for B-valued trimmed sums

    Indian Academy of Sciences (India)

    Annual Meetings · Mid Year Meetings · Discussion Meetings · Public Lectures · Lecture Workshops · Refresher Courses · Symposia · Live Streaming. Home; Journals; Proceedings – Mathematical Sciences; Volume 125; Issue 2. Limit law of the iterated logarithm for -valued trimmed sums. Ke-Ang Fu Yuyang Qiu Yeling ...

  20. Sensitivity of TRIM projections to management, harvest, yield, and stocking adjustment assumptions.

    Science.gov (United States)

    Susan J. Alexander

    1991-01-01

    The Timber Resource Inventory Model (TRIM) was used to make several projections of forest industry timber supply for the Douglas-fir region. The sensitivity of these projections to assumptions about management and yields is discussed. A base run is compared to runs in which yields were altered, stocking adjustment was eliminated, harvest assumptions were changed, and...

  1. Automotive Body Trim and Glass; Automotive Mechanics 2: 9045.05.

    Science.gov (United States)

    Dade County Public Schools, Miami, FL.

    This document presents an outline for a 135-hour course designed to help students become employable with skills, knowledge, attitudes, and values necessary for performing the required service of the automotive trim and glass mechanic. The course of study includes an orientation to the course, service tools and bench skills development, and a study…

  2. Some aspects of Trim-algorithm modernization for Monte-Carlo method

    International Nuclear Information System (INIS)

    Dovnar, S.V.; Grigor'ev, V.V.; Kamyshan, M.A.; Leont'ev, A.V.; Yanusko, S.V.

    2001-01-01

    Some aspects of Trim-algorithm modernization in Monte-Carlo method are discussed. This modification permits to raise the universality of program work with various potentials of ion-atom interactions and to improve the calculation precision for scattering angle θ c

  3. Evaluation of beef trim sampling methods for detection of Shiga toxin-producing Escherichia coli (STEC)

    Science.gov (United States)

    Presence of Shiga toxin-producing Escherichia coli (STEC) is a major concern in ground beef. Several methods for sampling beef trim prior to grinding are currently used in the beef industry. The purpose of this study was to determine the efficacy of the sampling methods for detecting STEC in beef ...

  4. Influence of tumbling, tumbling time, trim and sodium tripolyphosphate on quality and yield of cured hams

    NARCIS (Netherlands)

    Krause, R.J.; Ockerman, H.W.; Krol, B.; Moerman, P.C.; et al.

    1978-01-01

    Forty‐four boneless, cured hams were assigned to treatment groups to study the effect of tumbling, tumbling time (18 hr intermittent, 9.5 hr intermittent, 3 hr continuous), tumbling temperature (5°C and 15°C), sodium tripolyphosphate (TPP) pickle level (0 and 3.3%), and trim (lean, regular, and fat)

  5. Construction and assembling of the trim coils for the Milan superconducting cyclotron

    International Nuclear Information System (INIS)

    Baccaglioni, G.; Cartegni, G.C.; Fusetti, M.; Gini, L.; Grilli, L.

    1986-01-01

    This paper presents the main characteristics of the trim coils realized for the heavy ions superconducting cyclotron under construction at the Milan University. The guidelines in the choice of the conductor size, of the insulation and cooling parameters are discussed in some details. The main operations in the coils construction, as winding, impregnation, electrical tests and assembling, are described

  6. Integration of Value Stream Map and Healthcare Failure Mode and Effect Analysis into Six Sigma Methodology to Improve Process of Surgical Specimen Handling

    Directory of Open Access Journals (Sweden)

    Sheng-Hui Hung

    2015-01-01

    Full Text Available Specimen handling is a critical patient safety issue. Problematic handling process, such as misidentification (of patients, surgical site, and specimen counts, specimen loss, or improper specimen preparation can lead to serious patient harms and lawsuits. Value stream map (VSM is a tool used to find out non-value-added works, enhance the quality, and reduce the cost of the studied process. On the other hand, healthcare failure mode and effect analysis (HFMEA is now frequently employed to avoid possible medication errors in healthcare process. Both of them have a goal similar to Six Sigma methodology for process improvement. This study proposes a model that integrates VSM and HFMEA into the framework, which mainly consists of define, measure, analyze, improve, and control (DMAIC, of Six Sigma. A Six Sigma project for improving the process of surgical specimen handling in a hospital was conducted to demonstrate the effectiveness of the proposed model.

  7. Integration of Value Stream Map and Healthcare Failure Mode and Effect Analysis into Six Sigma Methodology to Improve Process of Surgical Specimen Handling.

    Science.gov (United States)

    Hung, Sheng-Hui; Wang, Pa-Chun; Lin, Hung-Chun; Chen, Hung-Ying; Su, Chao-Ton

    2015-01-01

    Specimen handling is a critical patient safety issue. Problematic handling process, such as misidentification (of patients, surgical site, and specimen counts), specimen loss, or improper specimen preparation can lead to serious patient harms and lawsuits. Value stream map (VSM) is a tool used to find out non-value-added works, enhance the quality, and reduce the cost of the studied process. On the other hand, healthcare failure mode and effect analysis (HFMEA) is now frequently employed to avoid possible medication errors in healthcare process. Both of them have a goal similar to Six Sigma methodology for process improvement. This study proposes a model that integrates VSM and HFMEA into the framework, which mainly consists of define, measure, analyze, improve, and control (DMAIC), of Six Sigma. A Six Sigma project for improving the process of surgical specimen handling in a hospital was conducted to demonstrate the effectiveness of the proposed model.

  8. New methodology to investigate potential contaminant mass fluxes at the stream-aquifer interface by combining integral pumping tests and streambed temperatures

    International Nuclear Information System (INIS)

    Kalbus, E.; Schmidt, C.; Bayer-Raich, M.; Leschik, S.; Reinstorf, F.; Balcke, G.U.; Schirmer, M.

    2007-01-01

    The spatial pattern and magnitude of mass fluxes at the stream-aquifer interface have important implications for the fate and transport of contaminants in river basins. Integral pumping tests were performed to quantify average concentrations of chlorinated benzenes in an unconfined aquifer partially penetrated by a stream. Four pumping wells were operated simultaneously for a time period of 5 days and sampled for contaminant concentrations. Streambed temperatures were mapped at multiple depths along a 60 m long stream reach to identify the spatial patterns of groundwater discharge and to quantify water fluxes at the stream-aquifer interface. The combined interpretation of the results showed average potential contaminant mass fluxes from the aquifer to the stream of 272 μg m -2 d -1 MCB and 71 μg m -2 d -1 DCB, respectively. This methodology combines a large-scale assessment of aquifer contamination with a high-resolution survey of groundwater discharge zones to estimate contaminant mass fluxes between aquifer and stream. - We provide a new methodology to quantify the potential contaminant mass flux from an aquifer to a stream

  9. [Tripartite motif-containing protein 34 (TRIM34) colocalized with micronuclei chromosome and hampers its movement to equatorial plate during the metaphase stage of mitosis].

    Science.gov (United States)

    Sun, Dakang; An, Xinye; Ji, Bing; Cheng, Yanli; Gao, Honglian; Tian, Mingming

    2016-06-01

    Objective To examine whether tripartite motif-containing protein 34 (TRIM34) is colocalized with micronuclei and investigate the influence on the movement of micronuclei chromosome in mitosis. Methods The eukaryotic expression vector TRIM34-pEGFP-N3 was constructed, identified and then transfected into HEK293T cells. With 4', 6-diamidino-2-phenylindole 2HCI (DAPI) staining, the colocalization between TRIM34 and micronuclei was observed under a fluorescence microscope. Moreover, MitoTracker(R)Deep Red was used to identify the colocalization between the complex of TRIM34-micronulei and mitochondria under a confocal microscope. Finally, the effect of TRIM34 on the movement of micronuclei chromosome in mitosis was examined. Results DNA sequencing confirmed that the vector TRIM34-pEGFP-N3 was constructed successfully. A fluorescence microscope revealed that TRIM34 could be colocalized with micronuclei in HEK293T cells transfected with TRIM34-pEGFP-N3. In the same manner, a confocal microscope distinctly showed that TRIM34 was colocalized with micronuclei similarly in appearance. However, there was no distinguished colocalization relationship between the complex of TRIM34-micronulei and mitochondria. Interestingly, the micronuclei chromosome conjugated with TRIM34 was hardly transferred to equatorial plate during the metaphase stage of mitosis. Conclusion TRIM34 is colocalized with micronuclei chromosome and hampers its movement to equatorial plate in mitosis.

  10. A methodology for developing high-integrity knowledge base using document analysis and ECPN matrix analysis with backward simulation

    International Nuclear Information System (INIS)

    Park, Joo Hyun

    1999-02-01

    When transitions occur in large systems such as nuclear power plants (NPPs) or industrial process plants, it is often difficult to diagnose them. Various computer-based operator-aiding systems have been developed in order to help operators diagnose the transitions of the plants. In procedures for developing knowledge base system like operator-aiding systems, the knowledge acquisition and the knowledge base verification are core activities. This dissertation describes a knowledge acquisition method and a knowledge base verification method for developing high-integrity knowledge base system of NPP expert systems. The knowledge acquisition is one of the most difficult and time-consuming activities in developing knowledge base systems. There are two kinds of knowledge acquisition methods in view of knowledge sources. One is an acquisition method from human expert. This method, however, is not adequate to acquire the knowledge of NPP expert systems because the number of experts is not sufficient. In this work, we propose a novel knowledge acquisition method through documents analysis. The knowledge base can be built correctly, rapidly, and partially automatically through this method. This method is especially useful when it is difficult to find domain experts. Reliability of knowledge base systems depends on the quality of their knowledge base. Petri Net has been used to verify knowledge bases due to their formal outputs. The methods using Petri Net however are difficult to apply to large and complex knowledge bases because the Net becomes very large and complex. Also, with Petri Net, it is difficult to find proper input patterns that make anomalies occur. In order to overcome this difficulty, in this work, the anomaly candidates detection methods are developed based on Extended CPN (ECPN) matrix analysis. This work also defines the backward simulation of CPN to find compact input patterns for anomaly detection, which starts simulation from the anomaly candidates

  11. How to treat a patient with chronic low back pain - methodology and results of the first international case conference of integrative medicine.

    Science.gov (United States)

    Brinkhaus, Benno; Lewith, George; Rehberg, Benno; Heusser, Peter; Cummings, Mike; Michalsen, Andreas; Teut, Michael; Willich, Stefan N; Irnich, Dominik

    2011-02-01

    Complementary and alternative medicine (CAM) is frequently used in patients in industrialised countries. Despite this popularity, there remains a considerable deficit of discourse and cooperation between physicians practicing CAM and conventional medicine. The aim is to present the methodology and results of the first international case conference on integrative medicine (IM) dealing with a patient with low back pain. In this paper the methodological tool "case conference on IM" is also described. The interactive case conference took place on November 20th, 2009 as part of the "2nd European Congress of IM" in Berlin, Germany. An experienced expert panel from both conventional medicine and CAM developed integrative medical diagnoses and therapeutic strategies using as their starting point an individual patient case on chronic low back pain (LBP). The case was selected because LBP is a common diagnosis with considerable economic impact and a problem which is often treated with CAM. In this case conference, the expert panel agreed on a diagnosis of "chronic non-specific LBP with somatic and psychological factors" and proposed multi-modal short- and long-term treatment including of CAM. The importance of the patient-physician-relationship and the consultation process with appropriate consultation time for treatment success was highlighted. There was consensus that the diagnostic process and resulting treatment plan should be individualised and focussed on the patient as a complete person, identifying the significance the disease has for the patient and not just on the disease for itself. Considerable differences were found amongst the experts regarding the first steps of treatment and each expert saw possibilities of "effective and adequate treatment" being met by their own individual treatment method. The case conference on integrative medicine stimulated an intensive exchange between the approaches used by conventional medicine and CAM clarifying different treatment

  12. The Methodology for Integral Assessment of the Impact of Renewable Energy on the Environment under Non-Stationary Economy

    Directory of Open Access Journals (Sweden)

    Petrakov Iaroslav V.

    2017-12-01

    Full Text Available The need to reduce anthropogenic load, eliminate threats to environmental safety and provide ecologically oriented development are one of the main global challenges of our time. At the same time, the replacement of traditional energy sources with alternatives ones requires a quantitative assessment of direct and indirect environmental impacts. The article analyzes the dynamics and structure of pollution in Ukraine in terms of its sources and forms as well as their impact on the carbon productivity of the GDP. It is proposed to assess the impact of alternative energy on the environment under non-stationary economy using an integral indicator that takes into account a number of factors, in particular the change in the share of RES in the total primary energy supply, share of renewable energy production, the index of greenhouse gases by the energy sector, change in the quality of atmospheric air in the urban populated area, amount of investment in reducing CO2 emissions, carbon intensity of energy production, share of thermal generation capacity that meets the ecological requirements of the EU.

  13. Lead intoxication in dogs: risk assessment of feeding dogs trimmings of lead-shot game.

    Science.gov (United States)

    Høgåsen, Helga R; Ørnsrud, Robin; Knutsen, Helle K; Bernhoft, Aksel

    2016-07-25

    Expanding lead-based bullets, commonly used for hunting of big game, produce a scattering of lead particles in the carcass around the wound channel. Trimmings around this channel, which are sometimes fed to dogs, may contain lead particles. The aim of this study was to assess potential health effects of feeding dogs such trimmings. Lead ingestion most commonly causes gastrointestinal and neurological clinical signs, although renal, skeletal, haematological, cardiovascular and biochemical effects have also been reported. Experimental data indicate that a daily dose of around 1 mg lead as lead acetate/kg body weight for ten days may be considered as a Lowest Observed Effect Level in dogs. Acute toxicity documentation from the Centers for Disease Control and Prevention indicates 300 mg/kg body weight as the lowest dose of lead acetate causing death in dogs after oral ingestion. Our assessment suggests that dogs fed trimmings of lead-shot game may be affected by the amounts of lead present, and that even deadly exposure could occasionally occur. The intestinal absorption of lead from bullets was assumed to be 10-80 % of that of lead acetate, reflecting both the variability in particle size and uncertainty about the bioavailability of metallic lead in dogs. Despite data gaps, this study indicates that feeding dogs trimmings of lead-shot game may represent a risk of lead intoxication. More research is needed to assess the exact consequences, if lead-based bullets are still to be used. Meanwhile, we recommend that trimmings close to the wound channel should be made inaccessible to dogs, as well as to other domestic or wild animals.

  14. Integrated technology selection for energy conservation and PAHs control in iron and steel industry: Methodology and case study

    International Nuclear Information System (INIS)

    Li, Li; Lu, Yonglong; Shi, Yajuan; Wang, Tieyu; Luo, Wei; Gosens, Jorrit; Chen, Peng; Li, Haiqian

    2013-01-01

    Energy conservation and PAHs (polycyclic aromatic hydrocarbon) control are two challenges for the iron and steel industry, especially where the industry has developed at high speed. How to select appropriate technologies to improve energy efficiency and control pollution from PAHs simultaneously is encountered by both the researchers and the decision makers. This study sets up a framework on technology selection and combination which integrates technology assessment, multiple objective programming and scenario analysis. It can predict proper technology combination for different emission controls, energy conservation targets and desired levels of production. An iron and steel factory in Southwestern China is cited as a case. It is shown that stricter PAHs control will drive the transformation from process control technology to alternative smelting technology. In low PAHs limit, 25% energy reduction is a threshold. Before inclusion of a restraint on energy consumption at 25% reduction, PAHs emission is the key limiting factor for the technology selection; while after inclusion of this restraint, energy consumption becomes the key limiting factor. The desired level of production will also influence the technology selection. This study can help decision makers to select appropriate technologies to meet the PAHs control objectives and energy conservation strategies in energy-intensive industries. - Highlights: ► We predict technical strategy for energy and PAHs reduction in iron and steel mill. ► With low PAHs control objectives, process control technologies are preferable. ► With medium and high PAHs control goals, alternative smelting technology is dominate. ► In low PAHs control objective, 25% energy reduction is a threshold

  15. Glocal clinical registries: pacemaker registry design and implementation for global and local integration--methodology and case study.

    Directory of Open Access Journals (Sweden)

    Kátia Regina da Silva

    facilitate data integration between healthcare and research settings, also being a useful framework to be used in other biomedical registries.

  16. A New Perspective on Binaural Integration Using Response Time Methodology: Super Capacity Revealed in Conditions of Binaural Masking Release

    Directory of Open Access Journals (Sweden)

    Jennifer eLentz

    2014-08-01

    Full Text Available This study applied reaction-time based methods to assess the workload capacity of binaural integration by comparing reaction time distributions for monaural and binaural tone-in-noise detection tasks. In the diotic contexts, an identical tone + noise stimulus was presented to each ear. In the dichotic contexts, an identical noise was presented to each ear, but the tone was presented to one of the ears 180o out of phase with respect to the other ear. Accuracy-based measurements have demonstrated a much lower signal detection threshold for the dichotic versus the diotic conditions, but accuracy-based techniques do not allow for assessment of system dynamics or resource allocation across time. Further, reaction times allow comparisons between these conditions at the same signal-to-noise ratio. Here, we apply a reaction-time based capacity coefficient, which provides an index of workload efficiency and quantifies the resource allocations for single ear versus two ear presentations. We demonstrate that the release from masking generated by the addition of an identical stimulus to one ear is limited-to-unlimited capacity (efficiency typically less than 1, consistent with less gain than would be expected by probability summation. However, the dichotic presentation leads to a significant increase in workload capacity (increased efficiency – most specifically at lower signal-to-noise ratios. These experimental results provide further evidence that configural processing plays a critical role in binaural masking release, and that these mechanisms may operate more strongly when the signal stimulus is difficult to detect, albeit still with nearly 100% accuracy.

  17. A new perspective on binaural integration using response time methodology: super capacity revealed in conditions of binaural masking release.

    Science.gov (United States)

    Lentz, Jennifer J; He, Yuan; Townsend, James T

    2014-01-01

    This study applied reaction-time based methods to assess the workload capacity of binaural integration by comparing reaction time (RT) distributions for monaural and binaural tone-in-noise detection tasks. In the diotic contexts, an identical tone + noise stimulus was presented to each ear. In the dichotic contexts, an identical noise was presented to each ear, but the tone was presented to one of the ears 180° out of phase with respect to the other ear. Accuracy-based measurements have demonstrated a much lower signal detection threshold for the dichotic vs. the diotic conditions, but accuracy-based techniques do not allow for assessment of system dynamics or resource allocation across time. Further, RTs allow comparisons between these conditions at the same signal-to-noise ratio. Here, we apply a reaction-time based capacity coefficient, which provides an index of workload efficiency and quantifies the resource allocations for single ear vs. two ear presentations. We demonstrate that the release from masking generated by the addition of an identical stimulus to one ear is limited-to-unlimited capacity (efficiency typically less than 1), consistent with less gain than would be expected by probability summation. However, the dichotic presentation leads to a significant increase in workload capacity (increased efficiency)-most specifically at lower signal-to-noise ratios. These experimental results provide further evidence that configural processing plays a critical role in binaural masking release, and that these mechanisms may operate more strongly when the signal stimulus is difficult to detect, albeit still with nearly 100% accuracy.

  18. An integrated methodology for sub-surface fracture characterization using microseismic data: A case study at the NW Geysers

    Science.gov (United States)

    Aminzadeh, Fred; Tafti, Tayeb A.; Maity, Debotyam

    2013-04-01

    Geothermal and unconventional hydrocarbon reservoirs are often characterized by low permeability and porosity. So, they are difficult to produce and require stimulation techniques, such as thermal shear deactivation and hydraulic fracturing. Fractures provide porosity for fluid storage and permeability for fluid movement and play an important role in production from this kind of reservoirs. Hence, characterization of fractures has become a vitally important consideration in every aspect of exploration, development and production so as to provide additional energy resources for the world. During the injection or production of fluid, induced seismicity (micro-seismic events) can be caused by reactivated shears created fractures or the natural fractures in shear zones and faults. Monitoring these events can help visualize fracture growth during injection stimulation. Although the locations of microseismic events can be a useful characterization tool and have been used by many authors, we go beyond these locations to characterize fractures more reliably. Tomographic inversion, fuzzy clustering, and shear wave splitting are three methods that can be applied to microseismic data to obtain reliable characteristics about fractured areas. In this article, we show how each method can help us in the characterization process. In addition, we demonstrate how they can be integrated with each other or with other data for a more holistic approach. The knowledge gained might be used to optimize drilling targets or stimulation jobs to reduce costs and maximize production. Some of the concepts discussed in this paper are general in nature, and may be more applicable to unconventional hydrocarbon reservoirs than the metamorphic and igneous reservoir rocks at The Geysers geothermal field.

  19. Glocal Clinical Registries: Pacemaker Registry Design and Implementation for Global and Local IntegrationMethodology and Case Study

    Science.gov (United States)

    da Silva, Kátia Regina; Costa, Roberto; Crevelari, Elizabeth Sartori; Lacerda, Marianna Sobral; de Moraes Albertini, Caio Marcos; Filho, Martino Martinelli; Santana, José Eduardo; Vissoci, João Ricardo Nickenig; Pietrobon, Ricardo; Barros, Jacson V.

    2013-01-01

    . Such approach has the potential to facilitate data integration between healthcare and research settings, also being a useful framework to be used in other biomedical registries. PMID:23936257

  20. Integrated Methodologies (SWOT, TOWS, LCA for Improving Production Chains and Environmental Sustainability of Kiwifruit and Baby Kiwi in Italy

    Directory of Open Access Journals (Sweden)

    Claudio Baudino

    2017-09-01

    Full Text Available Italy’s kiwifruit growers are considered to be world-leading players of the past 20 years. However, with this success come its challenges. In the last five years, a bacterial canker of kiwifruit known as Pseudomonas syringae pv. actinidiae (Psa has caused a dramatic reduction in the size of the areas cultivated, leading to several experienced Piedmontese Actinidia deliciosa growers beginning to cultivate the A. arguta. To better understand the potential for replacing the common kiwifruit in Italy’s Piedmont region with plantations of A. arguta and to attain a systematic approach and support for decision situations; we assessed the environmental impact of the two production chains (field and storage from a technical-operational perspective. The assessment was conducted through interviews with producers, field and warehouse technicians and sales managers in order to reveal the strengths and weaknesses of the two systems. The work presented below considers the application of the Life Cycle Assessment (LCA method for the field system (two different phases of the plantation and the SWOT (Strengths, Weaknesses, Opportunities, Threats analysis for the entire supply chain (field and warehouse management. Finally, a TOWS analysis (Threats, Opportunities, Weakness, Strengths integrated the results of both LCA and SWOT analyses and permitted to highlight the development strategies for A. arguta in Piedmont. The total orchard cycle for A. arguta presents an impact of 0.14 kg CO2 eq (GWP and for A. deliciosa an impact of 0.11 kg CO2 eq (GWP. Based on the synthesis of results from our TOWS analysis, we identified the following development strategies to help to shape the future A. arguta supply chain in Piedmont: Large-scale oriented; Berry fruits oriented; Export and organic oriented and Niche oriented.

  1. Advancement of the methodology for automated integration of external hazards into level 1 PSA modeling. Technical report; Weiterentwicklung der Methodik zur automatisierten Integration uebergreifender Einwirkungen in PSA-Modelle der Stufe 1. Technischer Fachbericht

    Energy Technology Data Exchange (ETDEWEB)

    Berner, Nadine; Herb, Joachim

    2017-03-15

    In the course of the research and development project RS1539 funded by the German Federal Ministry for Economics and Energy (BMWi) the methodology for the automated integration of hazards in Level 1 PSA models has been enhanced. Thereby, the analysis tool pyRiskRobot provides the methodological framework for mapping a generic spectrum of internal and external hazards onto complex PSA plant models. The reimplementation of the software tool via the programming language python extends the applicability and facilitates the handling of pyRiskRobot in comparison to the previous Ruby-based version RiskRobot. Moreover, the development of functions to perform the topological modelling of fault trees and the probabilistic specification of modified fault tree elements have been continued. Due to the reimplementation and further developments, the tool enables to systematically generate fault trees of varying complexity, to flexibly integrate fault trees in existing PSA models and to automatically duplicate interconnected topologies. Thus, pyRiskRobot allows the efficient and traceable realization of hazard specific, usually laborious modifications of PSA models. In addition, pyRiskRobot has been extended to serve as a functional interface between the data compilations comprising the potential influences of hazards on PSA relevant components and the data base of a PSA plant model. Based on this conceptual design, additional analyses of the data can be carried out prior to the integration within the PSA model topology. The reimplemented functionalities of pyRiskRobot have been validated with respect to reference applications, such as the modelling of an internal fire scenario, against the previous version RiskRobot. The existing method collection for the automated modification of fault tree topologies has been extended based on the requirements for further applications, among others the modelling of an external flooding scenario. The deduced hazard specific modelling approaches

  2. Study on seismic reliability for foundation grounds and surrounding slopes of nuclear power plants. Proposal of evaluation methodology and integration of seismic reliability evaluation system

    International Nuclear Information System (INIS)

    Ohtori, Yasuki; Kanatani, Mamoru

    2006-01-01

    This paper proposes an evaluation methodology of annual probability of failure for soil structures subjected to earthquakes and integrates the analysis system for seismic reliability of soil structures. The method is based on margin analysis, that evaluates the ground motion level at which structure is damaged. First, ground motion index that is strongly correlated with damage or response of the specific structure, is selected. The ultimate strength in terms of selected ground motion index is then evaluated. Next, variation of soil properties is taken into account for the evaluation of seismic stability of structures. The variation of the safety factor (SF) is evaluated and then the variation is converted into the variation of the specific ground motion index. Finally, the fragility curve is developed and then the annual probability of failure is evaluated combined with seismic hazard curve. The system facilitates the assessment of seismic reliability. A generator of random numbers, dynamic analysis program and stability analysis program are incorporated into one package. Once we define a structural model, distribution of the soil properties, input ground motions and so forth, list of safety factors for each sliding line is obtained. Monte Carlo Simulation (MCS), Latin Hypercube Sampling (LHS), point estimation method (PEM) and first order second moment (FOSM) implemented in this system are also introduced. As numerical examples, a ground foundation and a surrounding slope are assessed using the proposed method and the integrated system. (author)

  3. Methodology of the design of an integrated telecommunications and computer network in a control information system for artillery battalion fire support

    Directory of Open Access Journals (Sweden)

    Slobodan M. Miletić

    2012-04-01

    Full Text Available A Command Information System (CIS in a broader sense can be defined as a set of hardware and software solutions by which one achieves real-time integration of organizational structures, doctrine, technical and technological systems and facilities, information flows and processes for efficient and rational decision-making and functioning. Time distribution and quality of information directly affect the implementation of the decision making process and criteria for evaluating the effectiveness of the system in which the achievement of the most important role is an integrated telecommunications and computer network (ITCN, dimensioned to the spatial distribution of tactical combat units connecting all the elements in a communications unit. The aim is to establish the design methodology as a way of the ITCN necessary to conduct analysis and extract all the necessary elements for modeling that are mapped to the elements of network infrastructure, and then analyzed from the perspective of telecommunications communication standards and parameters of the layers of the OSI network model. A relevant way to verify the designed model ITCN is the development of a simulation model with which adequate results can be obtained. Conclusions on the compliance with the requirements of tactical combat and tactical communication requirements are drawn on the basis of these results.

  4. Conceptual design of a thermo-electrical energy storage system based on heat integration of thermodynamic cycles – Part A: Methodology and base case

    International Nuclear Information System (INIS)

    Morandin, Matteo; Maréchal, François; Mercangöz, Mehmet; Buchter, Florian

    2012-01-01

    The interest in large scale electricity storage (ES) with discharging time longer than 1 h and nominal power greater than 1 MW, is increasing worldwide as the increasing share of renewable energy, typically solar and wind energy, imposes severe load management issues. Thermo-electrical energy storage (TEES) based on thermodynamic cycles is currently under investigation at ABB corporate research as an alternative solution to pump hydro and compressed air energy storage. TEES is based on the conversion of electricity into thermal energy during charge by means of a heat pump and on the conversion of thermal energy into electricity during discharge by means of a thermal engine. The synthesis and the thermodynamic optimization of a TEES system based on hot water, ice storage and transcritical CO 2 cycles, is discussed in two papers. In this first paper a methodology for the conceptual design of a TEES system based on the analysis of the thermal integration between charging and discharging cycles through Pinch Analysis tools is introduced. According to such methodology, the heat exchanger network and temperatures and volumes of storage tanks are not defined a priori but are determined after the cycle parameters are optimized. For this purpose a heuristic procedure based on the interpretation of the composite curves obtained by optimizing the thermal integration between the cycles was developed. Such heuristic rules were implemented in a code that allows finding automatically the complete system design for given values of the intensive parameters of the charging and discharging cycles only. A base case system configuration is introduced and the results of its thermodynamic optimization are discussed here. A maximum roundtrip efficiency of 60% was obtained for the base case configuration assuming turbomachinery and heat exchanger performances in line with indications from manufacturers. -- Highlights: ► Energy storage based on water, ice, and transcritical CO 2 cycles is

  5. Trim9 Deletion Alters the Morphogenesis of Developing and Adult-Born Hippocampal Neurons and Impairs Spatial Learning and Memory.

    Science.gov (United States)

    Winkle, Cortney C; Olsen, Reid H J; Kim, Hyojin; Moy, Sheryl S; Song, Juan; Gupton, Stephanie L

    2016-05-04

    During hippocampal development, newly born neurons migrate to appropriate destinations, extend axons, and ramify dendritic arbors to establish functional circuitry. These developmental stages are recapitulated in the dentate gyrus of the adult hippocampus, where neurons are continuously generated and subsequently incorporate into existing, local circuitry. Here we demonstrate that the E3 ubiquitin ligase TRIM9 regulates these developmental stages in embryonic and adult-born mouse hippocampal neurons in vitro and in vivo Embryonic hippocampal and adult-born dentate granule neurons lacking Trim9 exhibit several morphological defects, including excessive dendritic arborization. Although gross anatomy of the hippocampus was not detectably altered by Trim9 deletion, a significant number of Trim9(-/-) adult-born dentate neurons localized inappropriately. These morphological and localization defects of hippocampal neurons in Trim9(-/-) mice were associated with extreme deficits in spatial learning and memory, suggesting that TRIM9-directed neuronal morphogenesis may be involved in hippocampal-dependent behaviors. Appropriate generation and incorporation of adult-born neurons in the dentate gyrus are critical for spatial learning and memory and other hippocampal functions. Here we identify the brain-enriched E3 ubiquitin ligase TRIM9 as a novel regulator of embryonic and adult hippocampal neuron shape acquisition and hippocampal-dependent behaviors. Genetic deletion of Trim9 elevated dendritic arborization of hippocampal neurons in vitro and in vivo Adult-born dentate granule cells lacking Trim9 similarly exhibited excessive dendritic arborization and mislocalization of cell bodies in vivo These cellular defects were associated with severe deficits in spatial learning and memory. Copyright © 2016 the authors 0270-6474/16/364940-19$15.00/0.

  6. Reliability Centered Maintenance - Methodologies

    Science.gov (United States)

    Kammerer, Catherine C.

    2009-01-01

    Journal article about Reliability Centered Maintenance (RCM) methodologies used by United Space Alliance, LLC (USA) in support of the Space Shuttle Program at Kennedy Space Center. The USA Reliability Centered Maintenance program differs from traditional RCM programs because various methodologies are utilized to take advantage of their respective strengths for each application. Based on operational experience, USA has customized the traditional RCM methodology into a streamlined lean logic path and has implemented the use of statistical tools to drive the process. USA RCM has integrated many of the L6S tools into both RCM methodologies. The tools utilized in the Measure, Analyze, and Improve phases of a Lean Six Sigma project lend themselves to application in the RCM process. All USA RCM methodologies meet the requirements defined in SAE JA 1011, Evaluation Criteria for Reliability-Centered Maintenance (RCM) Processes. The proposed article explores these methodologies.

  7. Genome-wide association study for claw disorders and trimming status in dairy cattle.

    Science.gov (United States)

    van der Spek, D; van Arendonk, J A M; Bovenhuis, H

    2015-02-01

    Performing a genome-wide association study (GWAS) might add to a better understanding of the development of claw disorders and the need for trimming. Therefore, the aim of the current study was to perform a GWAS on claw disorders and trimming status and to validate the results for claw disorders based on an independent data set. Data consisted of 20,474 cows with phenotypes for claw disorders and 50,238 cows with phenotypes for trimming status. Recorded claw disorders used in the current study were double sole (DS), interdigital hyperplasia (IH), sole hemorrhage (SH), sole ulcer (SU), white line separation (WLS), a combination of infectious claw disorders consisting of (inter-)digital dermatitis and heel erosion, and a combination of laminitis-related claw disorders (DS, SH, SU, and WLS). Of the cows with phenotypes for claw disorders, 1,771 cows were genotyped and these cow data were used for the GWAS on claw disorders. A SNP was considered significant when the false discovery rate≤0.05 and suggestive when the false discovery rate≤0.20. An independent data set of 185 genotyped bulls having at least 5 daughters with phenotypes (6,824 daughters in total) for claw disorders was used to validate significant and suggestive SNP detected based on the cow data. To analyze the trait "trimming status" (i.e., the need for claw trimming), a data set with 327 genotyped bulls having at least 5 daughters with phenotypes (18,525 daughters in total) was used. Based on the cow data, in total 10 significant and 45 suggestive SNP were detected for claw disorders. The 10 significant SNP were associated with SU, and mainly located on BTA8. The suggestive SNP were associated with DS, IH, SU, and laminitis-related claw disorders. Three of the suggestive SNP were validated in the data set of 185 bulls, and were located on BTA13, BTA14, and BTA17. For infectious claw disorders, SH, and WLS, no significant or suggestive SNP associations were detected. For trimming status, 1 significant

  8. Comparison of some properties of four provisional restorations resin: Trim, Tempron, Acropars TRII & Duralay (Aria Dent

    Directory of Open Access Journals (Sweden)

    Monzavi A.

    2006-08-01

    Full Text Available Background and Aim: Use of provisional restorations is one of the important phases in the treatment of patients who need fixed prosthesis. Some physical properties are required for these materials. The purpose of this study was the comparison of some physical properties of 4 kinds of resins: Trim, Tempron, Duralay (Aria Dent and Acropars TRII. Materials and Methods: In this experimental study, transverse-strength (TS, setting time (ST, polymerization shrinkage (PS and temperature rise (TR during polymerization were tested. In transverse strength test, 5 samples of each resin were made. TS testing was done with an Instron testing machine. ST testing (5 samples in each group was done with Gilmore needle. In PS test, 11 cylindric samples were prepared from each resin and the shrinkage was examined with digital micrometer (up to 24 hours. In TR test, after mixing the powder and liquid of resins (8 samples in each group, the temperature rise was recorded with 10 seconds interval (up to 15 minutes. Data were analyzed with one-way ANOVA and Tukey HSD tests with p<0.05 as the limit of significance. Results: In TS test, all samples of Trim were bent and no fracture was observed, while Tempron and Duralay showed no significant difference. Both Tempron and Duralay revealed high significant difference with Acropars TRII (P <0.01. In ST test, the difference between groups was significant (P<0.01. The lowest ST was observed in Acropars TRII (7 min, and the highest in Tempron (9.53 min. In PS test, significant difference was observed between Trim and Acropars TRII (P<0.01. PS was completed after 120 min in Tempron and Trim groups. However, PS continued to increase in other groups. In TR test, the difference between groups was significant (P<0.05. Duralay showed the highest TR and the lowest was seen in Trim. Conclusion: In this study, Trim showed better properties than other studied groups. Acropars TRII had the lowest strength. The highest temperature rise

  9. A study on the methodology of integrated safety assessment on low and intermediate level waste (LILW) managed in temporary storage facility at NPP

    International Nuclear Information System (INIS)

    Ahn, Min Ho

    2010-02-01

    Since 1978, the KHNP has been operating 20 NPPs (16 PWRs and 4 CANDUs) and generating about 67,000 drums (200 L) of LILW (as of December 31, 2005), which have been stored in the temporary storage facility (TSF) at each NPP due to the absence of a repository for the disposal of LILW. Therefore, the period of temporary storage of LILW is so long compared to other countries. Furthermore, the details with respect to the safety analyse on the TSF have not been considered in PSAR and FSAR. Especially, the risk assessment on the TSF has scarcely been conducted as opposed to many researches on the disposal of LILW. Since 2003, however, the IAEA has been recognized on the importance of predispoal management of LILW. And then, the regulatory frame of U.S. NRC was being shifted to risk-based regulation from the deterministic approach. Therefore, most of radioactive wastes including the LILW will be managed in terms of the risk-based graded approach to future regulation system called RIR (risk informed regulation). If the radioactive wastes do not quantitatively deal with the risk-based regulation, the radiological risk on some of radioactive wastes might be overestimated or underestimated regardless of the degree of the risk. According to a consequence of these situations, the numbers of the researches on the predisposal management of LILW have been required for the preparation on new regulatory frame. In this study, the main objective of this study is to establish the methodology of integrated safety assessment on LILW managed in the TSF at NPP, and to develop the integrated safety assessment code for routine operating condition and for for accident analysis on LILW managed in the TSF. In order to establish the methodology of integrated safety assessment on LILW managed in the TSF at NPP, three main parameters were considered: risk-based accident scenarios, radionuclide inventory, and atmospheric dispersion factor (χ/Q). Arbitrary accidents related to LILW management in the

  10. Integration

    DEFF Research Database (Denmark)

    Emerek, Ruth

    2004-01-01

    Bidraget diskuterer de forskellige intergrationsopfattelse i Danmark - og hvad der kan forstås ved vellykket integration......Bidraget diskuterer de forskellige intergrationsopfattelse i Danmark - og hvad der kan forstås ved vellykket integration...

  11. The Formulation of Binding Agent Concentration on Raw Restructured Goat Meat Trimming Product

    Directory of Open Access Journals (Sweden)

    Rini Mastuti

    2012-02-01

    Full Text Available The utilization of raw materials and formulation method would affect the quality of the processed meat product. Therefore, a research on the processing method to produce a raw structured product should be conducted. The research was testing a single factor comprises of following parameters: control (without binding agent; 0.3%, 0.5% and 0.7% sodium alginat and 0.3%, 0.5% and 0.7% carragenan, respectively. The results showed that the goat meat trimming could be used as raw materials in the production of the best restructured meat using 0.5% carragenan. This raw restructured meat produced had a loss weight of 1.67%, pH value  7.89, WHC  48.345, and moisture content  75.20%.   Keywords : sodium alginat, carragenan, raw restructured goat meat trimming.

  12. Investigation Of Adhesion Formation In New Stainless Steel Trim Spring Operated Pressure Relief Valves

    Energy Technology Data Exchange (ETDEWEB)

    Gross, Robert E. [Savannah River Site (SRS), Aiken, SC (United States); Bukowski, Julia V. [Villanova University, Villanova, PA (United States); Goble, William M. [exida, Sellersville, PA (United States)

    2013-04-16

    Examination of proof test data for new (not previously installed) stainless steel (SS) trim spring operated pressure relief valves (SOPRV) reveals that adhesions form between the seat and disc in about 46% of all such SOPRV. The forces needed to overcome these adhesions can be sufficiently large to cause the SOPRV to fail its proof test (FPT) prior to installation. Furthermore, a significant percentage of SOPRV which are found to FPT are also found to ''fail to open'' (FTO) meaning they would not relief excess pressure in the event of an overpressure event. The cases where adhesions result in FTO or FPT appear to be confined to SOPRV with diameters < 1 in and set pressures < 150 psig and the FTO are estimated to occur in 0.31% to 2.00% of this subpopulation of SS trim SOPRV. The reliability and safety implications of these finding for end-users who do not perform pre-installation testing of SOPRV are discussed.

  13. A trim-loss minimization in a produce-handling vehicle production plant

    Directory of Open Access Journals (Sweden)

    Apichai Ritvirool

    2007-01-01

    Full Text Available How to cut out the required pieces from raw materials by minimizing waste is a trim-loss problem. The integer linear programming (ILP model was developed to solve this problem. In addition, this ILPmodel could be used for planning an order over some future time period. Time horizon of ordering raw material including weekly, monthly, quarterly, and annually could be planned to reduce the trim loss. Thenumerical examples using an industrial case study of a produce-handling vehicle production plant were presented to illustrate how the proposed ILP model could be applied to actual systems and the types ofinformation that was obtained relative to implementation. The results showed that the proposed ILP model can be used as a decision support tool for selecting time horizon of order planning and cutting patterns todecrease material cost and waste from cutting raw material.

  14. an Integrated science based methodology

    Data.gov (United States)

    U.S. Environmental Protection Agency — The data is secondary in nature. Meaning that no data was generated as part of this review effort. Rather, data that was available in the peer-reviewed literature...

  15. The Host E3-Ubiquitin Ligase TRIM6 Ubiquitinates the Ebola Virus VP35 Protein and Promotes Virus Replication.

    Science.gov (United States)

    Bharaj, Preeti; Atkins, Colm; Luthra, Priya; Giraldo, Maria Isabel; Dawes, Brian E; Miorin, Lisa; Johnson, Jeffrey R; Krogan, Nevan J; Basler, Christopher F; Freiberg, Alexander N; Rajsbaum, Ricardo

    2017-09-15

    Ebola virus (EBOV), a member of the Filoviridae family, is a highly pathogenic virus that causes severe hemorrhagic fever in humans and is responsible for epidemics throughout sub-Saharan, central, and West Africa. The EBOV genome encodes VP35, an important viral protein involved in virus replication by acting as an essential cofactor of the viral polymerase as well as a potent antagonist of the host antiviral type I interferon (IFN-I) system. By using mass spectrometry analysis and coimmunoprecipitation assays, we show here that VP35 is ubiquitinated on lysine 309 (K309), a residue located on its IFN antagonist domain. We also found that VP35 interacts with TRIM6, a member of the E3-ubiquitin ligase tripartite motif (TRIM) family. We recently reported that TRIM6 promotes the synthesis of unanchored K48-linked polyubiquitin chains, which are not covalently attached to any protein, to induce efficient antiviral IFN-I-mediated responses. Consistent with this notion, VP35 also associated noncovalently with polyubiquitin chains and inhibited TRIM6-mediated IFN-I induction. Intriguingly, we also found that TRIM6 enhances EBOV polymerase activity in a minigenome assay and TRIM6 knockout cells have reduced replication of infectious EBOV, suggesting that VP35 hijacks TRIM6 to promote EBOV replication through ubiquitination. Our work provides evidence that TRIM6 is an important host cellular factor that promotes EBOV replication, and future studies will focus on whether TRIM6 could be targeted for therapeutic intervention against EBOV infection. IMPORTANCE EBOV belongs to a family of highly pathogenic viruses that cause severe hemorrhagic fever in humans and other mammals with high mortality rates (40 to 90%). Because of its high pathogenicity and lack of licensed antivirals and vaccines, EBOV is listed as a tier 1 select-agent risk group 4 pathogen. An important mechanism for the severity of EBOV infection is its suppression of innate immune responses. The EBOV VP35

  16. Evaluation of the UnTRIM model for 3-D tidal circulation

    Science.gov (United States)

    Cheng, R.T.; Casulli, V.; ,

    2001-01-01

    A family of numerical models, known as the TRIM models, shares the same modeling philosophy for solving the shallow water equations. A characteristic analysis of the shallow water equations points out that the numerical instability is controlled by the gravity wave terms in the momentum equations and by the transport terms in the continuity equation. A semi-implicit finite-difference scheme has been formulated so that these terms and the vertical diffusion terms are treated implicitly and the remaining terms explicitly to control the numerical stability and the computations are carried out over a uniform finite-difference computational mesh without invoking horizontal or vertical coordinate transformations. An unstructured grid version of TRIM model is introduced, or UnTRIM (pronounces as "you trim"), which preserves these basic numerical properties and modeling philosophy, only the computations are carried out over an unstructured orthogonal grid. The unstructured grid offers the flexibilities in representing complex study areas so that fine grid resolution can be placed in regions of interest, and coarse grids are used to cover the remaining domain. Thus, the computational efforts are concentrated in areas of importance, and an overall computational saving can be achieved because the total number of grid-points is dramatically reduced. To use this modeling approach, an unstructured grid mesh must be generated to properly reflect the properties of the domain of the investigation. The new modeling flexibility in grid structure is accompanied by new challenges associated with issues of grid generation. To take full advantage of this new model flexibility, the model grid generation should be guided by insights into the physics of the problems; and the insights needed may require a higher degree of modeling skill.

  17. UrQt: an efficient software for the Unsupervised Quality trimming of NGS data.

    Science.gov (United States)

    Modolo, Laurent; Lerat, Emmanuelle

    2015-04-29

    Quality control is a necessary step of any Next Generation Sequencing analysis. Although customary, this step still requires manual interventions to empirically choose tuning parameters according to various quality statistics. Moreover, current quality control procedures that provide a "good quality" data set, are not optimal and discard many informative nucleotides. To address these drawbacks, we present a new quality control method, implemented in UrQt software, for Unsupervised Quality trimming of Next Generation Sequencing reads. Our trimming procedure relies on a well-defined probabilistic framework to detect the best segmentation between two segments of unreliable nucleotides, framing a segment of informative nucleotides. Our software only requires one user-friendly parameter to define the minimal quality threshold (phred score) to consider a nucleotide to be informative, which is independent of both the experiment and the quality of the data. This procedure is implemented in C++ in an efficient and parallelized software with a low memory footprint. We tested the performances of UrQt compared to the best-known trimming programs, on seven RNA and DNA sequencing experiments and demonstrated its optimality in the resulting tradeoff between the number of trimmed nucleotides and the quality objective. By finding the best segmentation to delimit a segment of good quality nucleotides, UrQt greatly increases the number of reads and of nucleotides that can be retained for a given quality objective. UrQt source files, binary executables for different operating systems and documentation are freely available (under the GPLv3) at the following address: https://lbbe.univ-lyon1.fr/-UrQt-.html .

  18. Development and validation of the Treatment Related Impact Measure of Weight (TRIM-Weight

    Directory of Open Access Journals (Sweden)

    Lessard Suzanne

    2010-02-01

    Full Text Available Abstract Background The use of prescription anti-obesity medication (AOM is becoming increasingly common as treatment options grow and become more accessible. However, AOM may not be without a wide range of potentially negative impacts on patient functioning and well being. The Treatment Related Impact Measure (TRIM-Weight is an obesity treatment-specific patient reported outcomes (PRO measure designed to assess the key impacts of prescription anti-obesity medication. This paper will present the validation findings for the TRIM-Weight. Methods The online validation battery survey was administered in four countries (the U.S., U.K., Australia, and Canada. Eligible subjects were over age eighteen, currently taking a prescription AOM and were currently or had been obese during their life. Validation analyses were conducted according to an a priori statistical analysis plan. Item level psychometric and conceptual criteria were used to refine and reduce the preliminary item pool and factor analysis to identify structural domains was performed. Reliability and validity testing was then performed and the minimally importance difference (MID explored. Results Two hundred and eight subjects completed the survey. Twenty-one of the 43 items were dropped and a five-factor structure was achieved: Daily Life, Weight Management, Treatment Burden, Experience of Side Effects, and Psychological Health. A-priori criteria for internal consistency and test-retest coefficients for the total score and all five subscales were met. All pre-specified hypotheses for convergent and known group validity were also met with the exception of the domain of Daily Life (proven in an ad hoc analysis as well as the 1/2 standard deviation threshold for the MID. Conclusion The development and validation of the TRIM-Weight has been conducted according to well-defined principles for the creation of a PRO measure. Based on the evidence to date, the TRIM-Weight can be considered a brief

  19. Severe trimming and enhanced competition of laterals as a tool to delay ripening in Tempranillo vineyards under semiarid conditions

    Directory of Open Access Journals (Sweden)

    Luis Gonzaga Santesteban

    2017-05-01

    Significance and impact of the study: this study proves the potentiality of the joint use of trimming and increased irrigation to delay ripening, although it is necessary to analyze the implications the obtained delay has on other quality aspects. The lower anthocyanin and phenolic values observed in trimmed vines were not solely due to delayed ripening, as lower values were observed even when data were compared for a given total soluble solid content.

  20. UAV-Based Photogrammetry and Integrated Technologies for Architectural Applications—Methodological Strategies for the After-Quake Survey of Vertical Structures in Mantua (Italy)

    Science.gov (United States)

    Achille, Cristiana; Adami, Andrea; Chiarini, Silvia; Cremonesi, Stefano; Fassi, Francesco; Fregonese, Luigi; Taffurelli, Laura

    2015-01-01

    This paper examines the survey of tall buildings in an emergency context like in the case of post-seismic events. The after-earthquake survey has to guarantee time-savings, high precision and security during the operational stages. The main goal is to optimize the application of methodologies based on acquisition and automatic elaborations of photogrammetric data even with the use of Unmanned Aerial Vehicle (UAV) systems in order to provide fast and low cost operations. The suggested methods integrate new technologies with commonly used technologies like TLS and topographic acquisition. The value of the photogrammetric application is demonstrated by a test case, based on the comparison of acquisition, calibration and 3D modeling results in case of use of a laser scanner, metric camera and amateur reflex camera. The test would help us to demonstrate the efficiency of image based methods in the acquisition of complex architecture. The case study is Santa Barbara Bell tower in Mantua. The applied survey solution allows a complete 3D database of the complex architectural structure to be obtained for the extraction of all the information needed for significant intervention. This demonstrates the applicability of the photogrammetry using UAV for the survey of vertical structures, complex buildings and difficult accessible architectural parts, providing high precision results. PMID:26134108

  1. Methodological procedures and analytical instruments to evaluate an indicators integrated archive for urban management; Guida metodologica per la costruzione di un archivio integrato di indicatori urbani

    Energy Technology Data Exchange (ETDEWEB)

    Del Ciello, R; Napoleoni, S [ENEA, Centro Ricerche Casaccia, Rome (Italy). Dipt. Ambiente

    1998-07-01

    This guide provides the results of a research developed at ENEA (National Agency for new Technology, Energy and the Environment) Casaccia center (Rome, Italy) aimed to define methodological procedures and analytical instruments needed to carry out an indicators integrated archive for urban management. The guide also defines the scheme of a negotiation process aimed to reach and exchange data and information among governmental and local administrations, non-governmental organizations and scientific bodies. [Italian] Il lavoro presenta una sintesi dei risultati di una ricerca condotta presso il C.R. Casaccia dell'ENEA, relativia alla definizione di procedure metodologiche e strumenti di analisi ed elaborazione per realizzare un archivio integrato di indicatori per la gestione dei sistemi urbani. La guida, rivolta ai responsabili delle politiche urbane, deifinisce uno schema dei processi di condivisione degli indicatori urbani attraverso l'organizzazione di opportuni tavoli negoziali, costituiti da rappresentanti delle amministrazioni locali, dell'amministrazione centrale, delle categorie produttive e sociali e delle strutture tecniche operanti sul territorio.

  2. UAV-Based Photogrammetry and Integrated Technologies for Architectural Applications—Methodological Strategies for the After-Quake Survey of Vertical Structures in Mantua (Italy

    Directory of Open Access Journals (Sweden)

    Cristiana Achille

    2015-06-01

    Full Text Available This paper examines the survey of tall buildings in an emergency context like in the case of post-seismic events. The after-earthquake survey has to guarantee time-savings, high precision and security during the operational stages. The main goal is to optimize the application of methodologies based on acquisition and automatic elaborations of photogrammetric data even with the use of Unmanned Aerial Vehicle (UAV systems in order to provide fast and low cost operations. The suggested methods integrate new technologies with commonly used technologies like TLS and topographic acquisition. The value of the photogrammetric application is demonstrated by a test case, based on the comparison of acquisition, calibration and 3D modeling results in case of use of a laser scanner, metric camera and amateur reflex camera. The test would help us to demonstrate the efficiency of image based methods in the acquisition of complex architecture. The case study is Santa Barbara Bell tower in Mantua. The applied survey solution allows a complete 3D database of the complex architectural structure to be obtained for the extraction of all the information needed for significant intervention. This demonstrates the applicability of the photogrammetry using UAV for the survey of vertical structures, complex buildings and difficult accessible architectural parts, providing high precision results.

  3. UAV-Based Photogrammetry and Integrated Technologies for Architectural Applications--Methodological Strategies for the After-Quake Survey of Vertical Structures in Mantua (Italy).

    Science.gov (United States)

    Achille, Cristiana; Adami, Andrea; Chiarini, Silvia; Cremonesi, Stefano; Fassi, Francesco; Fregonese, Luigi; Taffurelli, Laura

    2015-06-30

    This paper examines the survey of tall buildings in an emergency context like in the case of post-seismic events. The after-earthquake survey has to guarantee time-savings, high precision and security during the operational stages. The main goal is to optimize the application of methodologies based on acquisition and automatic elaborations of photogrammetric data even with the use of Unmanned Aerial Vehicle (UAV) systems in order to provide fast and low cost operations. The suggested methods integrate new technologies with commonly used technologies like TLS and topographic acquisition. The value of the photogrammetric application is demonstrated by a test case, based on the comparison of acquisition, calibration and 3D modeling results in case of use of a laser scanner, metric camera and amateur reflex camera. The test would help us to demonstrate the efficiency of image based methods in the acquisition of complex architecture. The case study is Santa Barbara Bell tower in Mantua. The applied survey solution allows a complete 3D database of the complex architectural structure to be obtained for the extraction of all the information needed for significant intervention. This demonstrates the applicability of the photogrammetry using UAV for the survey of vertical structures, complex buildings and difficult accessible architectural parts, providing high precision results.

  4. Methodological procedures and analytical instruments to evaluate an indicators integrated archive for urban management; Guida metodologica per la costruzione di un archivio integrato di indicatori urbani

    Energy Technology Data Exchange (ETDEWEB)

    Del Ciello, R.; Napoleoni, S. [ENEA, Centro Ricerche Casaccia, Rome (Italy). Dipt. Ambiente

    1998-07-01

    This guide provides the results of a research developed at ENEA (National Agency for new Technology, Energy and the Environment) Casaccia center (Rome, Italy) aimed to define methodological procedures and analytical instruments needed to carry out an indicators integrated archive for urban management. The guide also defines the scheme of a negotiation process aimed to reach and exchange data and information among governmental and local administrations, non-governmental organizations and scientific bodies. [Italian] Il lavoro presenta una sintesi dei risultati di una ricerca condotta presso il C.R. Casaccia dell'ENEA, relativia alla definizione di procedure metodologiche e strumenti di analisi ed elaborazione per realizzare un archivio integrato di indicatori per la gestione dei sistemi urbani. La guida, rivolta ai responsabili delle politiche urbane, deifinisce uno schema dei processi di condivisione degli indicatori urbani attraverso l'organizzazione di opportuni tavoli negoziali, costituiti da rappresentanti delle amministrazioni locali, dell'amministrazione centrale, delle categorie produttive e sociali e delle strutture tecniche operanti sul territorio.

  5. A New Methodology for Open Pit Slope Design in Karst-Prone Ground Conditions Based on Integrated Stochastic-Limit Equilibrium Analysis

    Science.gov (United States)

    Zhang, Ke; Cao, Ping; Ma, Guowei; Fan, Wenchen; Meng, Jingjing; Li, Kaihui

    2016-07-01

    Using the Chengmenshan Copper Mine as a case study, a new methodology for open pit slope design in karst-prone ground conditions is presented based on integrated stochastic-limit equilibrium analysis. The numerical modeling and optimization design procedure contain a collection of drill core data, karst cave stochastic model generation, SLIDE simulation and bisection method optimization. Borehole investigations are performed, and the statistical result shows that the length of the karst cave fits a negative exponential distribution model, but the length of carbonatite does not exactly follow any standard distribution. The inverse transform method and acceptance-rejection method are used to reproduce the length of the karst cave and carbonatite, respectively. A code for karst cave stochastic model generation, named KCSMG, is developed. The stability of the rock slope with the karst cave stochastic model is analyzed by combining the KCSMG code and the SLIDE program. This approach is then applied to study the effect of the karst cave on the stability of the open pit slope, and a procedure to optimize the open pit slope angle is presented.

  6. Investigation and optimization of the novel UASB-MFC integrated system for sulfate removal and bioelectricity generation using the response surface methodology (RSM).

    Science.gov (United States)

    Zhang, Baogang; Zhang, Jing; Yang, Qi; Feng, Chuanping; Zhu, Yuling; Ye, Zhengfang; Ni, Jinren

    2012-11-01

    COD/sulfate ratio and hydraulic residence time (HRT), both of which influence sulfate loadings jointly, are recognized as the most two important affecting factors for sulfate removal and bioelectricity generation in the novel up-flow anaerobic sludge blanket reactor-microbial fuel cell (UASB-MFC) integrated system. The response surface methodology (RSM) was employed for the optimization of this system and the optimum condition with COD/sulfate ratio of 2.3 and HRT of 54.3h was obtained with the target of maximizing the power output. In terms of maximizing the total sulfate removal efficiency, the obtained optimum condition was COD/sulfate ratio of 3.7 and HRT of 55.6h. Experimental results indicated the undistorted simulation and reliable optimized results. These demonstrated that RSM was effective to evaluate and optimize the UASB-MFC system for sulfate removal and energy recovery, providing a promising guide to further improvement of the system for potential applications. Copyright © 2012 Elsevier Ltd. All rights reserved.

  7. Resampling nucleotide sequences with closest-neighbor trimming and its comparison to other methods.

    Directory of Open Access Journals (Sweden)

    Kouki Yonezawa

    Full Text Available A large number of nucleotide sequences of various pathogens are available in public databases. The growth of the datasets has resulted in an enormous increase in computational costs. Moreover, due to differences in surveillance activities, the number of sequences found in databases varies from one country to another and from year to year. Therefore, it is important to study resampling methods to reduce the sampling bias. A novel algorithm-called the closest-neighbor trimming method-that resamples a given number of sequences from a large nucleotide sequence dataset was proposed. The performance of the proposed algorithm was compared with other algorithms by using the nucleotide sequences of human H3N2 influenza viruses. We compared the closest-neighbor trimming method with the naive hierarchical clustering algorithm and [Formula: see text]-medoids clustering algorithm. Genetic information accumulated in public databases contains sampling bias. The closest-neighbor trimming method can thin out densely sampled sequences from a given dataset. Since nucleotide sequences are among the most widely used materials for life sciences, we anticipate that our algorithm to various datasets will result in reducing sampling bias.

  8. [Integrity].

    Science.gov (United States)

    Gómez Rodríguez, Rafael Ángel

    2014-01-01

    To say that someone possesses integrity is to claim that that person is almost predictable about responses to specific situations, that he or she can prudentially judge and to act correctly. There is a closed interrelationship between integrity and autonomy, and the autonomy rests on the deeper moral claim of all humans to integrity of the person. Integrity has two senses of significance for medical ethic: one sense refers to the integrity of the person in the bodily, psychosocial and intellectual elements; and in the second sense, the integrity is the virtue. Another facet of integrity of the person is la integrity of values we cherish and espouse. The physician must be a person of integrity if the integrity of the patient is to be safeguarded. The autonomy has reduced the violations in the past, but the character and virtues of the physician are the ultimate safeguard of autonomy of patient. A field very important in medicine is the scientific research. It is the character of the investigator that determines the moral quality of research. The problem arises when legitimate self-interests are replaced by selfish, particularly when human subjects are involved. The final safeguard of moral quality of research is the character and conscience of the investigator. Teaching must be relevant in the scientific field, but the most effective way to teach virtue ethics is through the example of the a respected scientist.

  9. Design of a Rad-Hard eFuse Trimming Circuit for Bandgap Voltage Reference for LHC Experiments Upgrades

    CERN Document Server

    Besirli, Mustafa; Koukab, Adil; Michelis, Stefano

    A precise and stable reference voltage is required to generate a stable output voltage in DC/DC converters. This reference voltage must be independent of temperature, power supply, radiation, intrinsic technology mismatch and process variation. This master's thesis reports the development of a rad-hard bandgap voltage reference with electrical fuse (eFuse) based analog calibration circuit in a commercial 130nm technology. According to the test results, the maximum error in the bandgap voltage (300mV in this application) was reduced from ±30mV to less than ±0.6mV thanks to the eFuse trimming. A temperature, power supply, radiation, mismatch and process-independent reference voltage was generated to provide reference voltage to first (bPOL12V) and second (bPOL2V5) stage DC/DC converters. This circuit will be integrated in bPOL12V and bPOL2V5 converters for high-luminosity LHC upgrades.

  10. Development and Operation of an Automatic Rotor Trim Control System for use During the UH-60 Individual Blade Control Wind Tunnel Test

    Science.gov (United States)

    Theodore, Colin R.

    2010-01-01

    A full-scale wind tunnel test to evaluate the effects of Individual Blade Control (IBC) on the performance, vibration, noise and loads of a UH-60A rotor was recently completed in the National Full-Scale Aerodynamics Complex (NFAC) 40- by 80-Foot Wind Tunnel [1]. A key component of this wind tunnel test was an automatic rotor trim control system that allowed the rotor trim state to be set more precisely, quickly and repeatably than was possible with the rotor operator setting the trim condition manually. The trim control system was also able to maintain the desired trim condition through changes in IBC actuation both in open- and closed-loop IBC modes, and through long-period transients in wind tunnel flow. This ability of the trim control system to automatically set and maintain a steady rotor trim enabled the effects of different IBC inputs to be compared at common trim conditions and to perform these tests quickly without requiring the rotor operator to re-trim the rotor. The trim control system described in this paper was developed specifically for use during the IBC wind tunnel test

  11. Methodology and analysis for effects of energy and angular distributions of secondary neutrons in fusion blankets and application to integral beryllium experiments

    International Nuclear Information System (INIS)

    Song, P.M.

    1990-01-01

    The main objective of the US/JAERI (Japan Atomic Energy Research Institute) collaborative experiment program on Fusion Breeder Neutronics is to estimate the uncertainties involved in predicting the TBR in Li 2 O. Beryllium has been used as a neutron multiplier in several experiments performed in that program. The shape of the C/E values (calculation/experiment) for the tritium production rate (TPR) from 6 Li, T 6 observed in these experiments indicate that there is underestimation in T 6 just behind the Be layer. This feature could be related to the Be cross-sections, especially in secondary energy (SED) and angular distribution (SAD) of emitted neutrons from reaction. These SED and SAD of the 9 Be(n,2n) cross-sections are subject to large uncertainties because of inadequate representation of the energy/angle distribution of the emitted neutrons. To access the uncertainty in predicting TPR that results from the current uncertainties in the cross-section data and SED/SAD of emitted neutrons, an extensive two-dimensional sensitivity/uncertainty analysis was performed with the current FORSS module, and new codes, JULIX, VARIX, and UNGSS which were specifically developed to incorporate the new methodology of the present work in treating SED/SAD sensitivity analyses. When analyses were performed, it was found that the local standard deviation in T 6 is 2.1 to 9.3% in the integrated cross-section, 5.2 to 11.2% in the SED (direct variation with the ENDF/BLANL), and 0.14% to 1.37% in the SAD, respectively, with largest uncertainties occurring inside the beryllium layer. The uncertainty in T 6 is mainly attributed to the current uncertainties in 9 Be(n,elastic), 16 O and 7 Li data

  12. TRIMe7-CypA, an alternative splicing isoform of TRIMCyp in rhesus macaque, negatively modulates TRIM5α activity

    Energy Technology Data Exchange (ETDEWEB)

    Na, Lei [Harbin Veterinary Research Institute of the Chinese Academy of Agricultural Sciences, Harbin 150001 (China); Tang, Yan-Dong [Harbin Veterinary Research Institute of the Chinese Academy of Agricultural Sciences, Harbin 150001 (China); Biotechnology Institute of Southern Medical University, Guangzhou 510515 (China); Liu, Jian-Dong; Yu, Chang-Qing; Sun, Liu-Ke; Lin, Yue-Zhi; Wang, Xue-Feng [Harbin Veterinary Research Institute of the Chinese Academy of Agricultural Sciences, Harbin 150001 (China); Wang, Xiaojun, E-mail: xjw@hvri.ac.cn [Harbin Veterinary Research Institute of the Chinese Academy of Agricultural Sciences, Harbin 150001 (China); Zhou, Jian-Hua, E-mail: jianhua_uc@126.com [Harbin Veterinary Research Institute of the Chinese Academy of Agricultural Sciences, Harbin 150001 (China); Harbin Pharmaceutical Group Biovaccine Company, Harbin 150069 (China)

    2014-04-04

    Highlights: • TRIMe7-CypA expresses in rhesus and pig-tailed, but not long-tailed macaques. • TRIMe7-CypA does not show the restriction to a HIV-GFP report virus in vitro. • It acts as a negative modulator to TRIM5α likely by competitive inhibition. - Abstract: The existence of innate, host-specific restriction factors is a major obstacle to the development of nonhuman primate models for AIDS studies, and TRIM5α is one of the most important of these restriction factors. In recent years, a TRIM5 chimeric gene that was retrotransposed by a cyclophilin A (CypA) cDNA was identified in certain macaque species. The TRIM5α-CypA fusion protein, TRIMCyp, which was expressed in these monkeys, had lost its restriction ability toward HIV-1. We previously found that TRIMe7-CypA, an alternative splicing isoform of the TRIMCyp transcripts, was expressed in pig-tailed and rhesus macaques but absent in long-tailed macaques. In this study, the anti-HIV-1 activity of TRIMe7-CypA in the rhesus macaque (RhTRIMe7-CypA) was investigated. The over-expression of RhTRIMe7-CypA in CrFK, HeLa and HEK293T cells did not restrict the infection or replication of an HIV-1-GFP reporter virus in these cells. As a positive control, rhesus (rh)TRIM5α strongly inhibited the reporter virus. Intriguingly, the anti-HIV-1 activity of RhTRIM5α was significantly reduced in a dose-dependent manner by the co-repression of RhTRIMe7-CypA. Our data indicate that although the RhTRIMe7-CypA isoform does not appear to restrict HIV-1, it may act as a negative modulator of TRIM family proteins, presumably by competitive inhibition.

  13. TRIMe7-CypA, an alternative splicing isoform of TRIMCyp in rhesus macaque, negatively modulates TRIM5α activity

    International Nuclear Information System (INIS)

    Na, Lei; Tang, Yan-Dong; Liu, Jian-Dong; Yu, Chang-Qing; Sun, Liu-Ke; Lin, Yue-Zhi; Wang, Xue-Feng; Wang, Xiaojun; Zhou, Jian-Hua

    2014-01-01

    Highlights: • TRIMe7-CypA expresses in rhesus and pig-tailed, but not long-tailed macaques. • TRIMe7-CypA does not show the restriction to a HIV-GFP report virus in vitro. • It acts as a negative modulator to TRIM5α likely by competitive inhibition. - Abstract: The existence of innate, host-specific restriction factors is a major obstacle to the development of nonhuman primate models for AIDS studies, and TRIM5α is one of the most important of these restriction factors. In recent years, a TRIM5 chimeric gene that was retrotransposed by a cyclophilin A (CypA) cDNA was identified in certain macaque species. The TRIM5α-CypA fusion protein, TRIMCyp, which was expressed in these monkeys, had lost its restriction ability toward HIV-1. We previously found that TRIMe7-CypA, an alternative splicing isoform of the TRIMCyp transcripts, was expressed in pig-tailed and rhesus macaques but absent in long-tailed macaques. In this study, the anti-HIV-1 activity of TRIMe7-CypA in the rhesus macaque (RhTRIMe7-CypA) was investigated. The over-expression of RhTRIMe7-CypA in CrFK, HeLa and HEK293T cells did not restrict the infection or replication of an HIV-1-GFP reporter virus in these cells. As a positive control, rhesus (rh)TRIM5α strongly inhibited the reporter virus. Intriguingly, the anti-HIV-1 activity of RhTRIM5α was significantly reduced in a dose-dependent manner by the co-repression of RhTRIMe7-CypA. Our data indicate that although the RhTRIMe7-CypA isoform does not appear to restrict HIV-1, it may act as a negative modulator of TRIM family proteins, presumably by competitive inhibition

  14. An end-users oriented methodology for enhancing the integration of knowledge on soil-water-sediment systems in River Basin Management: an illustration from the AquaTerra project.

    Science.gov (United States)

    Merly, Corinne; Chapman, Antony; Mouvet, Christophe

    2012-01-01

    Research results in environmental and socio-economic sciences are often under-used by stakeholders involved in the management of natural resources. To minimise this gap, the FP6 EU interdisciplinary project AquaTerra (AT) developed an end-users' integration methodology in order to ensure that the data, knowledge and tools related to the soil-water-sediment system that were generated by the project were delivered in a meaningful way for end-users, thus improving their uptake. The methodology and examples of its application are presented in this paper. From the 408 project deliverables, 96 key findings were identified, 53 related to data and knowledge, and 43 describing advanced tools. River Basin Management (RBM) stakeholders workshops identified 8 main RBM issues and 25 specific stakeholders' questions related to RBM which were classified into seven groups of cross-cutting issues, namely scale, climate change, non-climatic change, the need for systemic approaches, communication and participation, international and inter-basin coordination and collaboration, and the implementation of the Water Framework Directive. The integration methodology enabled an assessment of how AT key findings meet stakeholders' demands, and for each main RBM issue and for each specific question, described the added-value of the AT project in terms of knowledge and tools generated, key parameters to consider, and recommendations that can be made to stakeholders and the wider scientific community. Added value and limitations of the integration methodology and its outcomes are discussed and recommendations are provided to further improve integration methodology and bridge the gaps between scientific research data and their potential uptake by end-users.

  15. Over-expression of TRIM37 promotes cell migration and metastasis in hepatocellular carcinoma by activating Wnt/β-catenin signaling

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Jianxin; Yu, Chao; Chen, Meiyuan; Tian, She; Sun, Chengyi, E-mail: chenyisun11@163.com

    2015-09-04

    Hepatocellular carcinoma (HCC) is the most common cancer in the world especially in East Asia and Africa. Advanced stage, metastasis and frequent relapse are responsible for the poor prognosis of HCC. However, the precise mechanisms underlying HCC remained unclear. So it is urgent to identify the pathological processes and relevant molecules of HCC. TRIM37 is an E3 ligase and has been observed deregulated expression in various tumors. Recent studies of TRIM37 have implicated that TRIM37 played critical roles in cell proliferation and other processes. In the present study, we demonstrated that TRIM37 expression was notably up-regulated in HCC samples and was associated with advanced stage and tumor volume, which all indicating the poor outcomes. We also found that TRIM37 could serve as an independent prognostic factor of HCC. During the course of in vitro and in vivo work, we showed that TRIM37 promoted HCC cells migration and metastasis by inducing EMT. Furthermore, we revealed that the effect of TRIM37 mediated EMT in HCC cells was achieved by the activation of Wnt/β-catenin signaling. These finding may provide insight into the understanding of TRIM37 as a novel critical factor of HCC and a candidate target for HCC treatment. - Highlights: • Highly expression of TRIM37 is found in HCC samples compared with nontumorous samples. • TRIM37 expression is correlated with advanced HCC stages and could be an independent prognostic factor. • TRIM37 promotes cell proliferation and metastasis. • We report an E3 ligase TRIM37 affects Wnt/β-catenin signaling.

  16. Design and manufacturing status of trim coils for the Wendelstein 7-X stellarator experiment

    Energy Technology Data Exchange (ETDEWEB)

    Riße, K., E-mail: konrad.risse@ipp.mpg.de [Max-Planck-Institut für Plasmaphysik, Greifswald (Germany); Rummel, Th.; Freundt, S.; Dudek, A.; Renard, S.; Bykov, V.; Köppen, M. [Max-Planck-Institut für Plasmaphysik, Greifswald (Germany); Langish, S.; Neilson, G.H.; Brown, Th.; Chrzanowski, J.; Mardenfeld, M.; Malinowski, F.; Khodak, A.; Zhao, X. [Princeton Plasma Physics Laboratory, Princeton, NJ (United States); Eksaa, G. [Everson Tesla Inc., Nazareth, PA (United States)

    2013-10-15

    Highlights: ► The trim coil system will fine tune the main magnetic field during plasma operation by reducing the magnetic field errors. ► The coil design and operational parameters are fixed, the manufacturing is running. ► The coils are equipped with temperature sensors and a voltage tap system to monitor the coil temperature. ► The max. operational deflection is in the order of 4.5 mm; the max. shearing stress across bond planes is of order 16 MPa. ► Special clamps equipped with elastomeric pads allow fixing the coils on the outer cryostat wall. -- Abstract: The stellarator fusion experiment Wendelstein 7-X (W7-X) is currently under construction at the Max-Planck-Institut für Plasmaphysik in Greifswald, Germany. The main magnetic field will be provided by a superconducting magnet system which generates a fivefold toroidal periodic magnetic field. However, unavoidable tolerances can result in small deviations of the magnetic field which disturb the toroidal periodicity. In order to have a tool to influence these field errors five additional normal conducting trim coils were designed to allow fine tuning of the main magnetic field during plasma operation. In the frame of an international cooperation the trim coils will be contributed by the US partners. Princeton Plasma Physics Laboratory has accomplished several tasks to develop the final design ready for manufacturing e.g. detailed manufacturing design for the winding and for the coil connection area. The design work was accompanied by a detailed analysis of resulting forces and moments to prove the design. The manufacturing of the coils is running at Everson Tesla Inc; the first two coils were received at IPP.

  17. The Salmonella Effector Protein SopA Modulates Innate Immune Responses by Targeting TRIM E3 Ligase Family Members.

    Directory of Open Access Journals (Sweden)

    Jana Kamanova

    2016-04-01

    Full Text Available Salmonella Typhimurium stimulates inflammatory responses in the intestinal epithelium, which are essential for its ability to replicate within the intestinal tract. Stimulation of these responses is strictly dependent on the activity of a type III secretion system encoded within its pathogenicity island 1, which through the delivery of effector proteins, triggers signaling pathways leading to inflammation. One of these effectors is SopA, a HECT-type E3 ligase, which is required for the efficient stimulation of inflammation in an animal model of Salmonella Typhimurium infection. We show here that SopA contributes to the stimulation of innate immune responses by targeting two host E3 ubiquitin ligases, TRIM56 and TRIM65. We also found that TRIM65 interacts with the innate immune receptor MDA5 enhancing its ability to stimulate interferon-β signaling. Therefore, by targeting TRIM56 and TRIM65, SopA can stimulate signaling through two innate immune receptors, RIG-I and MDA5. These findings describe a Salmonella mechanism to modulate inflammatory responses by directly targeting innate immune signaling mechanisms.

  18. PENGARUH KARAKTERISTIK PEKERJAAN DAN IKLIM KOMUNIKASI TERHADAP KEPUASAN KERJA KARYAWAN OPERATOR BAGIAN TRIMMING I PT KRAMA YUDHA RATU MOTOR

    Directory of Open Access Journals (Sweden)

    Agung AWS Waspodo

    2013-09-01

    Full Text Available The purpose of the research are: 1 To know the description of job characteristics, communication climate, and job satisfaction employees at trimming 1 PT Krama Yudha Ratu Motor. 2 To know about the influence of job characteristics toward job satisfaction trimming 1 employee’s at PT Krama Yudha Ratu Motor. 3 To know about the influence of communication climate toward job satisfaction trimming 1 employee’s at PT Krama Yudha Ratu Motor. 4 To know about the influence of job characteristics and communication climate toward job satisfaction trimming 1 employee’s at PT Krama Yudha Ratu Motor. The analysis implemented in this research are descriptive and explanatory analysis. This research is taken 71 trimming 1 employee’s at PT Krama Yudha Ratu Motor. While data collection by using questionnaire and cultivated processed using SPSS 16. The result showed that: 1 Job characteristics has a significant influence on job satisfaction. 2 communication climate has a significant influence on job satisfaction. 3 job characteristics and communication climate has a significant influence on job satisfaction.

  19. Frequent silencing of the candidate tumor suppressor TRIM58 by promoter methylation in early-stage lung adenocarcinoma.

    Science.gov (United States)

    Kajiura, Koichiro; Masuda, Kiyoshi; Naruto, Takuya; Kohmoto, Tomohiro; Watabnabe, Miki; Tsuboi, Mitsuhiro; Takizawa, Hiromitsu; Kondo, Kazuya; Tangoku, Akira; Imoto, Issei

    2017-01-10

    In this study, we aimed to identify novel drivers that would be epigenetically altered through aberrant methylation in early-stage lung adenocarcinoma (LADC), regardless of the presence or absence of tobacco smoking-induced epigenetic field defects. Through genome-wide screening for aberrantly methylated CpG islands (CGIs) in 12 clinically uniform, stage-I LADC cases affecting six non-smokers and six smokers, we identified candidate tumor-suppressor genes (TSGs) inactivated by hypermethylation. Through systematic expression analyses of those candidates in panels of additional tumor samples and cell lines treated or not treated with 5-aza-deoxycitidine followed by validation analyses of cancer-specific silencing by CGI hypermethylation using a public database, we identified TRIM58 as the most prominent candidate for TSG. TRIM58 was robustly silenced by hypermethylation even in early-stage primary LADC, and the restoration of TRIM58 expression in LADC cell lines inhibited cell growth in vitro and in vivo in anchorage-dependent and -independent manners. Our findings suggest that aberrant inactivation of TRIM58 consequent to CGI hypermethylation might stimulate the early carcinogenesis of LADC regardless of smoking status; furthermore, TRIM58 methylation might be a possible early diagnostic and epigenetic therapeutic target in LADC.

  20. Two impulse trajectory optimization for the RAE-B orbit trim problem

    Science.gov (United States)

    Payne, M. H.; Pines, S.; Horsewood, J. L.

    1972-01-01

    The results are reported of work on an appropriate approach to the solution of the optimum two-impulse transfer problem between orbits of specified inclination. The task included a literature search to identify the current state of the art and a definition of the suggested approach for the specific application of a lunar orbit trim. The applications of the results to the problem are included. The formulation for a computer program developed under this task following a more conventional approach is also included.